WorldWideScience

Sample records for surface-piercing central flotation

  1. Modified Contact Line Dynamics about a Surface-Piercing Hydrofoil

    Science.gov (United States)

    Grivel, Morgane; Jeon, David; Gharib, Morteza

    2016-11-01

    The contact line around a surface-piercing hydrofoil is modified by introducing alternating hydrophobic and hydrophilic bands along one side of the body. These bands are either aligned perpendicular or parallel to the flow direction. The other side of the hydrofoil is un-patterned and retains its original, uniformly hydrophilic properties. The hydrofoil is mounted onto air bearings, such that it can freely move side-to-side in the water tunnel. A force sensor is attached to the setup via a universal joint in order to measure the forces acting on the body for several Reynolds numbers (ranging from 104 to 105) and angles of attack (ranging from -10o to 10o) . Cameras are also used to record the resulting flow structures and free surface elevation. The generation of wave trains and an altered free-surface elevation (also associated with the generation of surface waves) are observed over a wide range flow conditions. Force measurements elucidate how introducing these flow features impacts the forces acting on the hydrofoil, specifically with regards to the generation of lateral forces due to the asymmetric wetting conditions on either side of the hydrofoil. Work is funded by ONR Grant N00014-11-1-0031 and NSF GRFP Grant DGE-1144469.

  2. Differences in scour around a single surface-piercing cylinder and a submerged cylinder

    Science.gov (United States)

    Beninati, M. L.; Volpe, M. A.; Riley, D. R.; Krane, M.

    2011-12-01

    The equilibrium state of scour for a single surface piercing cylinder and a submerged cylinder of specific aspect ratio are presented. The equilibrium state is defined by a scour depth and associated time interval for a given set of flow conditions. Control variables such as sediment coarseness (or grain size) and cylinder size are held constant, while the flow intensity is varied. Sediment bed form topology is characterized with a series of two-dimensional slices across the bed for both the surface-piercing and submerged cylinder cases. Test results will help identify the geometry and pattern of the scour around the cylinders to aid in the optimal design of marine hydrokinetic (MHK) support structures in an effort to help minimize the deleterious impact of these devices on the local substrate. This study is performed in the small-scale testing platform in the hydraulic flume facility (32 ft long, 4 ft wide and 1.25 ft deep) in the Environmental Fluid Mechanics and Hydraulics Laboratory (EFM&H) at Bucknell University. The cylinders, of the same material and diameter, are placed centrally in the sediment filled test section (2.5 ft long, 2 ft wide and 0.75 ft deep) of the platform. Flow field measurements are taken with a 16-MHz Micro Acoustic Doppler Velocimeter while water depth is acquired using an ultrasonic distance sensor. These devices are attached to a gantry system that can be accurately positioned anywhere in the test section. Clear-water conditions (in the absence of live-bed scour) are maintained to study the effect of the horseshoe and wake vortices on the displacement of sediment around the cylinder as well as downstream of the device. Bed form topology is measured using an HR Wallingford 2D Sediment Bed Profiler with a low-powered laser distance sensor to accurately characterize changes in bed form around the cylinders. Additionally, specifications for testing such as operational procedures for start-up and shut-down of the facility are given.

  3. An efficient domain decomposition strategy for wave loads on surface piercing circular cylinders

    DEFF Research Database (Denmark)

    Paulsen, Bo Terp; Bredmose, Henrik; Bingham, Harry B.

    2014-01-01

    A fully nonlinear domain decomposed solver is proposed for efficient computations of wave loads on surface piercing structures in the time domain. A fully nonlinear potential flow solver was combined with a fully nonlinear Navier–Stokes/VOF solver via generalized coupling zones of arbitrary shape....... Sensitivity tests of the extent of the inner Navier–Stokes/VOF domain were carried out. Numerical computations of wave loads on surface piercing circular cylinders at intermediate water depths are presented. Four different test cases of increasing complexity were considered; 1) weakly nonlinear regular waves...

  4. Differences in Scour for Submerged and Surface Piercing Circular Cylinders in Tandem

    Science.gov (United States)

    Pulvino, N. T.; Riley, D.; Beninati, M. L.; Krane, M.; Fontaine, A.

    2012-12-01

    An experimental study was conducted to investigate how the scour hole of surface piercing and submerged cylinders in tandem is affected by the separation of the cylinders. The study was motivated by the need to predict the environmental effects of Marine Hydrokinetic (MHK) turbines arrays where the cylinders used represent the bluff bodies of MHK turbines. Small scale experiments were performed to find scour rate and scour statistics; including: scour size and deposition. The cases studied were tandem cylinders separated by 1, 2, 3, 4, 6, 8, 10, and 12 diameters (D = 2.54 cm). These studies were performed in a test section in the hydraulic flume facility (1.22-m-wide, 0.38-m-deep, and 9.75-m-long) at Bucknell University. The bottoms of each cylinder tested were taped in 0.318 cm color-coded increments and buried beneath the sediment. This allowed for visual determination of the scour rate by looking at how many strips had been uncovered at intervals over three hours of testing at live bed conditions. Subsequently, bed form topology was measured using an HR Wallingford 2D Sediment Bed Profiler with a low-powered laser distance sensor. Results show that surface piercing cylinders in tandem consistently have a wider scour hole than submerged cylinders. Furthermore, it is determined that the threshold for when the tandem cylinders have separate scour holes occurring at a separation of 10 diameters for both sets of cylinders.

  5. Analysis of Ventilation Regimes of the Oblique Wedge-Shaped Surface Piercing Hydrofoil During Initial Water Entry Process

    Directory of Open Access Journals (Sweden)

    Ghadimi Parviz

    2018-03-01

    Full Text Available The suction side of a surface piercing hydrofoil, as a section of a Surface Piercing Propeller (SPP, is usually exposed to three phases of flow consisting air, water, and vapour. Hence, ventilation and cavitation pattern of such section during the initial phase of water entry plays an essential role for the propeller’s operational curves. Accordingly, in the current paper a numerical simulation of a simple surface piercing hydrofoil in the form of an oblique wedge is conducted in three-phase environment by using the coupled URANS and VOF equations. The obtained results are validated against water entry experiments and super-cavitation tunnel test data. The resulting pressure curves and free surface profiles of the wedge water entry are presented for different velocity ratios ranging from 0.12 to 0.64. Non-dimensional forces and efficiency relations are defined in order to present the wedge water entry characteristics. Congruent patterns are observed between the performance curves of the propeller and the wedge in different fully ventilated or partially cavitated operation modes. The transition trend from fully ventilated to partially cavitated operation of the surface piercing section of a SPP is studied and analyzed through wedge’s performance during the transitional period.

  6. Control of a flexible, surface-piercing hydrofoil for high-speed, small-scale applications

    Science.gov (United States)

    Bousquet, Gabriel; Triantafyllou, Michael; Slotine, Jean-Jacques

    2016-11-01

    In recent years, hydrofoils have become ubiquitous in the design of high performance surface vehicles such as sailboats. They have proven particularly useful at small scales: while the speed of displacement-hull sailboats of length L is limited by their hull speed √{ gL } , due to wave making resistance, such limitations do not apply to hydrofoil crafts and sailboats. Such crafts of length O(1 - 10 m) are capable of reaching speeds in excess of 45 kts, often far faster than the wind. Besides, in the quest for super-maneuverability, actuated hydrofoils enable the efficient generation and control of large forces. With the intent to ultimately enable the design of small-scale, high-speed, and super-maneuverable surface vehicles, we investigate the problem of controlling the lift force generated by a flexible, surface-piercing hydrofoil traveling at high speed through a random wave field. We design a test platform composed of a rudder-like vertical foil, which is actuated in pitch, and instrumented with velocity, force, and immersion sensors. We present a feedback linearization controller, designed to operate over a wide range of velocities and sea states. Validation experiments are carried out on-the-field at speeds ranging from 3 to 10+m/s.

  7. Water Surface Ripples Generated by the Turbulent Boundary Layer of a Surface-Piercing Moving Wall

    Science.gov (United States)

    Washuta, N.; Masnadi, N.; Duncan, J. H.

    2014-11-01

    Free surface ripples created by subsurface turbulence along a surface-piercing moving wall are studied experimentally. In this experiment, a meter-wide stainless steel belt travels horizontally in a loop around two rollers with vertically oriented axes, which are separated by 7.5 meters. One of the two 7.5-m-long belt sections between the rollers is in contact with the water in a large open-surface water tank and the water level is adjusted so that the top of the belt pierces the water free surface. The belt is launched from rest with a 3 g acceleration in order to quickly reach a steady state velocity. This belt motion creates a temporally evolving boundary layer analogous to the spatially evolving boundary layer created along the side of a ship hull moving at the belt velocity, with a length equivalent to the length of belt that has passed the measurement region. The water surface ripples generated by the subsurface turbulence are measured in a plane normal to the belt using a cinematic LIF technique. It is found that the overall RMS surface fluctuations increase linearly with belt speed and that the spatial distributions of the fluctuations show a sharp increase near the wall. The support of the Office of Naval Research is gratefully acknowledged.

  8. Recent Results from Analysis of Flow Structures and Energy Modes Induced by Viscous Wave around a Surface-Piercing Cylinder

    Directory of Open Access Journals (Sweden)

    Giancarlo Alfonsi

    2017-01-01

    Full Text Available Due to its relevance in ocean engineering, the subject of the flow field generated by water waves around a vertical circular cylinder piercing the free surface has recently started to be considered by several research groups. In particular, we studied this problem starting from the velocity-potential framework, then the implementation of the numerical solution of the Euler equations in their velocity-pressure formulation, and finally the performance of the integration of the Navier-Stokes equations in primitive variables. We also developed and applied methods of extraction of the flow coherent structures and most energetic modes. In this work, we present some new results of our research directed, in particular, toward the clarification of the main nonintuitive character of the phenomenon of interaction between a wave and a surface-piercing cylinder, namely, the fact that the wave exerts its maximum force and exhibits its maximum run-up on the cylindrical obstacle at different instants. The understanding of this phenomenon becomes of crucial importance in the perspective of governing the entity of the wave run-up on the obstacle by means of wave-flow-control techniques.

  9. Classification of Flotation Frothers

    Directory of Open Access Journals (Sweden)

    Jan Drzymala

    2018-02-01

    Full Text Available In this paper, a scheme of flotation frothers classification is presented. The scheme first indicates the physical system in which a frother is present and four of them i.e., pure state, aqueous solution, aqueous solution/gas system and aqueous solution/gas/solid system are distinguished. As a result, there are numerous classifications of flotation frothers. The classifications can be organized into a scheme described in detail in this paper. The frother can be present in one of four physical systems, that is pure state, aqueous solution, aqueous solution/gas and aqueous solution/gas/solid system. It results from the paper that a meaningful classification of frothers relies on choosing the physical system and next feature, trend, parameter or parameters according to which the classification is performed. The proposed classification can play a useful role in characterizing and evaluation of flotation frothers.

  10. Flotation of Biological Materials

    Directory of Open Access Journals (Sweden)

    George Z. Kyzas

    2014-03-01

    Full Text Available Flotation constitutes a gravity separation process, which originated from the minerals processing field. However, it has, nowadays, found several other applications, as for example in the wastewater treatment field. Concerning the necessary bubble generation method, typically dispersed-air or dissolved-air flotation was mainly used. Various types of biological materials were tested and floated efficiently, such as bacteria, fungi, yeasts, activated sludge, grape stalks, etc. Innovative processes have been studied in our Laboratory, particularly for metal ions removal, involving the initial abstraction of heavy metal ions onto a sorbent (including a biosorbent: in the first, the application of a flotation stage followed for the efficient downstream separation of metal-laden particles. The ability of microorganisms to remove metal ions from dilute aqueous solutions (as most wastewaters are is a well-known property. The second separation process, also applied effectively, was a new hybrid cell of microfiltration combined with flotation. Sustainability in this field and its significance for the chemical and process industry is commented.

  11. Bibliometric analysis on kaolinite flotation

    Directory of Open Access Journals (Sweden)

    Gabriela Lieberknecht

    Full Text Available Abstract The current work presents a bibliometric discussion on articles published worldwide concerning kaolinite flotation in international journals from 1992 to 2015. In total, 39 articles were selected from Elsevier's database, SciVerse ScienceDirect. This work allowed to recognize and identify which are the thematic and methodological trends that are being used, in addition to the main collectors used in kaolinite flotation. The results show that a significant amount of articles is produced by Chinese authors, especially from 2013, as China is the second highest aluminum producer in the world, and kaolinite is the reject in the reverse flotation process of diaspore. The results showed the difficulty of working with kaolinite flotation individually and confirmed that there is scientific collaboration among authors. Bibliometric analysis showed that the reagents used in kaolinite flotation tests are mostly derived from cationic nitrogenated compounds. Additionally, best recovery results from kaolinite flotation occurred in acidic media.

  12. Flotation of PAH contaminated dredged sludge

    NARCIS (Netherlands)

    Mulleneers, H.; Roubroeks, S.; Bruning, H.; Rulkens, W.H.; Koopal, L.K.

    2000-01-01

    The applicability of dissolved air flotation to remediate contaminated sediments of "Overschie" (Rotterdam) and "Petrol Harbor" (Amsterdam) is studied. Several flotation reagents (Diesel Fuel, Montanol, Aerophine, Aerofroth) are applied to enhance the flotation efficiency. The physical chemical

  13. Hydrodynamic aspects of flotation separation

    Directory of Open Access Journals (Sweden)

    Peleka Efrosyni N.

    2016-01-01

    Full Text Available Flotation separation is mainly used for removing particulates from aqueous dispersions. It is widely used for ore beneficiation and recovering valuable materials. This paper reviews the hydrodynamics of flotation separations and comments on selected recent publications. Units are distinguished as cells of ideal and non-ideal flow. A brief introduction to hydrodynamics is included to explain an original study of the hybrid flotation-microfiltration cell, effective for heavy metal ion removal.

  14. Pyrolitics Oils in Coal Flotation

    Czech Academy of Sciences Publication Activity Database

    Čáblík, V.; Išek, J.; Herková, M.; Halas, J.; Čáblíková, L.; Vaculíková, Lenka

    2014-01-01

    Roč. 34, č. 2 (2014), s. 9-14 ISSN 1640-4920 Institutional support: RVO:68145535 Keywords : pyrolytic oils * flotation, black coal * new flotation reagents Subject RIV: CB - Analytical Chemistry, Separation http://homen.vsb.cz/hgf/546/IM_2014_02.pdf

  15. Wastewater treatment by flotation

    Directory of Open Access Journals (Sweden)

    F.P. Puget

    2000-12-01

    Full Text Available This work deals with the performance analysis of a separation set-up characterized by the ejector-hydrocyclone association, applied in the treatment of a synthetic dairy wastewater effluent. The results obtained were compared with the results from a flotation column (cylindrical body of a hydrocyclone operated both batch and continuously. As far as the experimental set-up studied in this work and the operating conditions imposed to the process, it is possible to reach a 25% decrease in the total effluent chemical oxygen demand (COD. This corresponds approximately to 60% of the COD of the material in suspension. The best results are obtained for ratios air flow rate-feed flow rate (Qair/Q L greater then 0.15 and for ratios underflow rate-overflow rate (Qu/Qo lower than 1.0.

  16. Waste water treatment by flotation

    Directory of Open Access Journals (Sweden)

    Camelia Badulescu

    2005-11-01

    Full Text Available The flotation is succesfully applied as a cleaning method of waste water refineries, textile fabrics (tissues, food industry, paper plants, oils plants, etc. In the flotation process with the released air, first of all, the water is saturated with air compressed at pressures between 0,3 – 3 bar, followed by the relaxed phenomenon of the air-water solution in a flotation cell with slowly flowing. The supersaturation could be applied in the waste water treatment. In this case the waste water, which is in the atmospheric equilibrum, is introduced in a closed space where the depression is 0,3 – 0,5 bar. Our paper presents the hypobaric flotation cell and the technological flow of cleaning of domestic waste waters

  17. Mechanisms of beryl flotation: a literature review

    International Nuclear Information System (INIS)

    Torem, M.L.

    1988-01-01

    This paper shows a review about the investigations that have been done on the mechanisms of flotation of beryl and its dependence in relation to the presence of fluoride species. It is also analised the anionic flotation of the mineral and the effect of cations in the pulp of flotation. (author) [pt

  18. Roles of surfactants in flotation deinking

    Science.gov (United States)

    Yulin Zhao; Yulin Deng; J.Y. Zhu

    2004-01-01

    Flotation deinking is a common practice for removing ink from wastepaper, and it is becoming a key process in many recycling paper mills. Flotation deinking was successfully introduced to the paper recycling industry in the 1980s, and its applications in wax removal, sticky control, and fiber fractionation have attracted great research interest. A successful flotation...

  19. Cationic flotation of some lithium ores

    International Nuclear Information System (INIS)

    Valadao, G.E.S.; Peres, A.E.C.; Silva, H.C. da

    1984-01-01

    The cationic flotation of some lithium ores (spodumene, amblygonite, petalite, lepidolite) is studied by the measure of zeta potential and micro-flotation tests in Hallimond tube. The effect of some modifier agents (corn starch, meta sodium silicate) on the lithium flotation is studied. (M.A.C.) [pt

  20. Thermodynamic condition for ''Gamma'' flotation

    International Nuclear Information System (INIS)

    Kaoma, J.; Yarar, B.

    1989-01-01

    Using the definition of the critical surface tension of wetting solids (Γc) and Gibb's adsorption isotherm, coupled with Young-Dupre's equation, the equilibrium thermodynamic condition for 'GAMMA' flotation has been derived. It is defined by the relation, Cos Oe=Γc/Γlg. At equilibrium for 'Gamma' flotation to occur, the liquid/gas interfacial tension (9γlg) should be larger than the critical surface tension of wetting of the solid surface, meaning that the equilibrium contact angle (Oe) should be greater than Zero, or cos Oe < 1, a Pre- requisite for the solid/gas bubble attachment. This definition holds for solid surfaces in the absence of any specific adsorption at the solid/liquid and solid/gas inter faces. Contact angle and flotation data are presented to sustain this definition. (author)., 15 refs., 9 figs

  1. Oil removal from industrial wastewater using flotation in a ...

    African Journals Online (AJOL)

    This paper investigates the flotation of oil from wastewater in a laboratory-scale mechanically agitated flotation cell. Mechanical flotation cells are used commercially for oil flotation but, to the authors' best knowledge, there are no studies on their flotation performance in the literature. Some researchers have suggested that ...

  2. Assessment of the controlling factors in TurboFlotation by statistical analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ofori, P.K.; Firth, B.A.; Howes, T. [CSIRO Division of Energy Technology, Qld. (Australia)

    2000-07-01

    TurboFlotation is a new flotation system that has the advantage of large throughput per unit volume and low fluid inventory. The influence of process and design parameters on the performance of the TurboFlotation system as applied to coal flotation has been studied and statistical models developed to predict the performance of the system under various operating conditions. The study was done in two stages. The first part of the study involved the use of the Plackett-Burman screening experimental design to identify the important factors affecting the process performance, followed by a central composite design to optimize the system. Frother concentration, collector dosage, feed percent solids and feed flowrate were identified as the factors with significant effect on process performance. 12 refs., 20 figs., 8 tabs.

  3. Chemical Deinking Flotation Efficiency Of Coloured Toner

    Directory of Open Access Journals (Sweden)

    Višnja Mikac Dadić

    2009-01-01

    Full Text Available Recycling of paper printed with colour laser printer xerox phaser 7700 has been investigated in this work. The recycling was performed by chemical deinking with double stage flotation with the usage of anion surfactant. Froths collected by flotation were re-floated in purpose to increase the usage of fibers. The efficiency of first flotation of magenta particles (98.3%, cyan (96.9% and carbon ones (91.5% was calculated from results of the image analysis method. The same method was not effective for the identification of the yellow toner particles. The particle size is important characteristic for flotation efficiency. The efficiency of the first flotation is the best for smallest particles (magenta and for them the second flotation is unnecessary, while for bigger toner particles (cyan, carbon second flotation is desirable. The efficiency of second (abf flotation as a function of each colour (cyan 78.0%, magenta 58.6% and carbon 61.4% of particle number detected by image analysis method has shown that double stage flotation is successful method of improving the usage of fibers in recycling process.

  4. Chemical Deinking Flotation Efficiency Of Coloured Toner

    Directory of Open Access Journals (Sweden)

    Zeljka Barbaric-Mikocevic

    2009-11-01

    Full Text Available Recycling of paper printed with colour laser printer xerox phaser 7700 has been investigated in this work. The recycling was performed by chemical deinking with double stage flotation with the usage of anion surfactant. Froths collected by flotation were re-floated in purpose to increase the usage of fibers. The efficiency of first flotation of magenta particles (98.3%, cyan (96.9% and carbon ones (91.5% was calculated from results of the image analysis method. The same method was not effective for the identification of the yellow toner particles. The particle size is important characteristic for flotation efficiency. The efficiency of the first flotation is the best for smallest particles (magenta and for them the second flotation is unnecessary, while for bigger toner particles (cyan, carbon second flotation is desirable. The efficiency of second (abf flotation as a function of each colour (cyan 78.0%, magenta 58.6% and carbon 61.4% of particle number detected by image analysis method has shown that double stage flotation is successful method of improving the usage of fibres in recycling process.

  5. Further Investigations on Simultaneous Ultrasonic Coal Flotation

    Directory of Open Access Journals (Sweden)

    Safak Gokhan Ozkan

    2017-09-01

    Full Text Available This study investigates the flotation performance of a representative hard coal slime sample (d80 particle size of minus 0.2 mm obtained from the Prosper-Haniel coal preparation plant located in Bottrop, Germany. Flotation was carried out with a newly designed flotation cell refurbished from an old ultrasonic cleaning bath (2.5 L volume equipped with a single frequency (35 kHz and two different power levels (80–160 W and a sub-aeration-type flotation machine operating at a stable impeller speed (1200 rpm and air rate (2.5 L/min. The reagent combination for conventional and simultaneous ultrasonic coal flotation tests was Ekofol-440 at variable dosages (40–300 g/t with controlling water temperature (20–25 °C at natural pH (6.5–7.0. The batch coal flotation results were analyzed by comparing the combustible recovery (% and separation efficiency (% values, taking mass yield and ash concentrations of the froths and tailings into account. It was found that simultaneous ultrasonic coal flotation increased yield and recovery values of the floated products with lower ash values than the conventional flotation despite using similar reagent dosages. Furthermore, particle size distribution of the ultrasonically treated and untreated coals was measured. Finely distributed coal particles seemed to be agglomerated during the ultrasonic treatment, while ash-forming slimes were removed by hydrodynamic cavitation.

  6. On fiber rejection loss in flotation deinking

    Science.gov (United States)

    J.Y. Zhu; Freya Tan

    2005-04-01

    Reducing fiber rejection loss in flotation deinking is very important to conserve natural resources and reduce the cost of secondary fibers in paper recycling. This study examined two aspects of the problem, fiber consistency in the rejection stream and rate of Froth (or wet stream) rejection. Flotation experiments were conducted using both nylon and wood fibers in...

  7. Recovery of primary cassiterite by flotation

    International Nuclear Information System (INIS)

    Oliveira, J.F. de; Penna, M.T.M.; Adamian, R.

    1985-01-01

    The flotation of cassiterite ores using samples of primary ore from Pela Ema, Brazil is studied. The cassiterite was characterized by X-ray fluorescence analysis. The samples were submitted to size reduction up ro minus loo m in order to obtain liberation of cassiterite in excess of 95%. The flotation tests were carried out without desliming. Several collectors and depressants were investigated, as well as the influence of the concentration of these reactants and the pH factor upon flotation of cassiterite. The results were analysed considering the flotability of the minerals, and the electrophoretic mobility of cassiterite, both in the presence and absence of selected collectors. (Author) [pt

  8. Influence of flotation cell volume and solids mass on kinetics of sulfide ore flotation

    OpenAIRE

    Plawski Michal; Bakalarz Alicja

    2016-01-01

    The paper presents studies on the influence of flotation cell capacity and mass of solids in the suspension on the flotation kinetics of sulfide copper ore. A sample of copper ore that was collected from the Polkowice Mine of KGHM Polska Miedz S.A. in Poland was used in the experiments. It was determined that neither the volume of flotation cell nor the mass of solids had influence on the type of kinetics equation of flotation. Copper-bearing minerals floated according to the second-order equ...

  9. Latex for selective flotation of coal slurry

    Energy Technology Data Exchange (ETDEWEB)

    Tsyrlov, M.Ya.; Kovrizhko, L.F.; Nikitin, I.N.; Preobrazhenskii, B.P.

    1982-01-01

    The study relates to an attempt to develop a latex with reduced foam-formation for use in flotation of coal slurries. It was established that latex synthesised with paraffinate and more especially with a colophony emulsifier, should not give rise to excessive foaming during flotation. The mix formula and colloid-chemical properties of the two butadiene-styrene latices developed are described. 2 references.

  10. Flotation separation of waste plastics for recycling-A review.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Fu, Jian-gang; Liu, You-nian

    2015-07-01

    The sharp increase of plastic wastes results in great social and environmental pressures, and recycling, as an effective way currently available to reduce the negative impacts of plastic wastes, represents one of the most dynamic areas in the plastics industry today. Froth flotation is a promising method to solve the key problem of recycling process, namely separation of plastic mixtures. This review surveys recent literature on plastics flotation, focusing on specific features compared to ores flotation, strategies, methods and principles, flotation equipments, and current challenges. In terms of separation methods, plastics flotation is divided into gamma flotation, adsorption of reagents, surface modification and physical regulation. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Uranium(6) ionic flotation from carbonate solutions

    International Nuclear Information System (INIS)

    Pavlenko, S.N.; Legenchenko, I.A.; Menchuk, V.V.

    1983-01-01

    Regularities and the mechanism of the process of U(6) flotation separation with bromine N-alkylpyridinium salts are investigated. Bromine hexadecylpyrinium is proved to be the most effective of the collectors studied (10 to 16 carbon atoms in the alkyl circuit). It is shown that within the range of 20 to 34 deg C the temperature does not have a noticeable effect on the flotation process. A further temperature increase brings about a sharp decrease in the extraction. The process parameters versus of the pH value of the solution are also studied. The maximum extraction is achieved in the range of pH=5-6. The investigation into the effect of collector consumption on the flotation extraction rate has shown that an extraction maximum is achieved in the range of 3 to 4 moles of the collector per 1 mole of the colligating agent. The diagram of the sublate formation is presented

  12. Coal flotation optimization using modified flotation parameters and combustible recovery in a Jameson cell

    International Nuclear Information System (INIS)

    Vapur, Hueseyin; Bayat, Oktay; Ucurum, Metin

    2010-01-01

    This study discusses a new coal flotation optimization approach. It is conducted using modified flotation parameters and combustible recovery. The experimental work was evaluated in two stages. In the first stage, recoveries (1, 2, 3, 5 and 8 min of flotation times) of Jameson flotation operating parameters were fitted to first-order kinetic model, R = R ∞ [1 - exp (-kt)] where R was recovery at t time, R ∞ was ultimate recovery and k was the first-order rate constant to draw the time recovery curves in the experimental study. Two parameters, the ultimate recovery (R ∞ ) and first-order rate constant (k), were then obtained from the model to fit an experimental time recovery curve. A modified flotation rate constant (K m ) defined as product of R ∞ and k, i.e., K m = R ∞ * k, and selectivity index (SI) defined as the ratio of the modified rate constant of coal to the modified rate constant of ash (SI)=K m of Coal/K m of Ash), which could be collectively called 'modified flotation parameters'. It was used to determine of the sub and upper values of operation variables. In the second one, combustible recovery (%) and ash content (%) were used to optimization of the Jameson flotation variables and it was found that d 80 = 0.250 mm particle size, 1/1 vegetable oil acids/kerosene ratio, 20% solids pulp density, 0.600 L/min wash water rate and 40 cm downcomer immersion dept could be used to separate efficiently coal from ash. Final concentrate was obtained with 94.83% combustible recovery and 17.86% ash content at optimum conditions after 8 min flotation time.

  13. Effect of flotation on preparation of coal-water slurries

    Energy Technology Data Exchange (ETDEWEB)

    Ding, K.; Laskowski, J.S. [University of British Columbia, Vancouver, BC (Canada)

    2009-07-01

    In order to study the effect of flotation reagents on the properties of coal-water slurry, a sub-bituminous coal was cleaned via either forward flotation or reverse flotation. The froth product from the forward flotation, obtained with the use of diesel oil and MIBC, and the tailings of the reverse flotation, carried out with dextrin-tannic acid depressants and dodecyltrimethylammonium chloride collector, were used in the preparation of coal-water slurries. It was shown that while it was possible to obtain the coal-water slurry with a high-solids content from the coal rendered hydrophilic (tailings from the coal reverse flotation), in the case of the hydrophobic product (froth product from the forward flotation) a dispersing agent was required to obtain the coal-water slurry of the same high-solids content.

  14. (2-PYRIDYLAZO)RESORCINOL FOR FLOTATION

    African Journals Online (AJOL)

    PS-2, COOMET No. 0002-1999 BG, SOD No. 311а-98; and PS-3, COOMET No. 0003-1999 BG, SOD No. 312а-. 98) and zinc sulfide concentrates. KEY WORDS: Iron(II), Fe-PAR complex, Flotation, Spectrophotometry, Soils, Zinc sulfide concentrates. INTRODUCTION. 4-(2-Pyridylazo)resorcinol (PAR) is one of the most ...

  15. Flotation of uraniferous phosphorus ore from Itataia

    International Nuclear Information System (INIS)

    Aquino, J.A. de

    1984-01-01

    Flotation conditions, in laboratory and pilot scale, were established in a sample of Itataia uraniferous phosphorus ore which was basically constitute of apatite and calcite. The system of reagents-tall oil, collamil and sodium silicate-was studied in rougher, scavenger and cleaner stage. (M.A.C.) [pt

  16. Influence of flotation cell volume and solids mass on kinetics of sulfide ore flotation

    Directory of Open Access Journals (Sweden)

    Plawski Michal

    2016-01-01

    Full Text Available The paper presents studies on the influence of flotation cell capacity and mass of solids in the suspension on the flotation kinetics of sulfide copper ore. A sample of copper ore that was collected from the Polkowice Mine of KGHM Polska Miedz S.A. in Poland was used in the experiments. It was determined that neither the volume of flotation cell nor the mass of solids had influence on the type of kinetics equation of flotation. Copper-bearing minerals floated according to the second-order equation, while the remaining components according to the first-order equation. The kinetic rate constants and maximum recovery of the studied components decreased with increasing solids mass in the flotation cell, regardless of the capacity of the cell. The best results were obtained for tests using a 1.0 dm3 cell, while the less favorable kinetics results were observed in the test with the smallest cell of 0.75 dm3 volume. The obtained results can be helpful in choosing the most appropriate methodology of upgrading the sulfide copper ore from Poland in order to obtain the best kinetics results.

  17. Improved algal harvesting using suspended air flotation.

    Science.gov (United States)

    Wiley, Patrick E; Brenneman, Kristine J; Jacobson, Arne E

    2009-07-01

    Current methods to remove algae from a liquid medium are energy intensive and expensive. This study characterized algae contained within a wastewater oxidation pond and sought to identify a more efficient harvesting technique. Analysis of oxidation pond wastewater revealed that algae, consisting primarily of Chlorella and Scenedesmus, composed approximately 80% of the solids inventory during the study period. Results demonstrated that suspended air flotation (SAF) could harvest algae with a lower air:solids (A/S) ratio, lower energy requirements, and higher loading rates compared to dissolved air flotation (DAF) (P plants by enabling cost effective means to reduce solids content of the final effluent. Furthermore, use of SAF to harvest commercially grown Chlorella and Scenedesmus may reduce manufacturing costs of algal-based products such as fuel, fertilizer, and fish food.

  18. Ultrasonic flotational separation of syrup with polyacrylamide

    International Nuclear Information System (INIS)

    Zeng SiXian; Qiu TaiQiu; Xie XiongFei; Hu SongQing

    1998-01-01

    A 60 degrees Bx solution of Australian raw sugar was treated at 80 degrees C with 300 ppm phosphoric acid and neutralized to pH 7 with Ca(OH)2. The resulting syrup (as model cane syrup rather than phosphatated liquor?) was subjected to flotational separation with and without ultrasonic vibration (16.5-33 kHz, 20-300 W) and/or addition of polyacrylamide (PAM; dose not stated)

  19. Dissolved Air Flotation of arsenic adsorbent particles

    Directory of Open Access Journals (Sweden)

    Mario Enrique Santander Muñoz

    2015-01-01

    Full Text Available The removal of arsenic from synthetic effluent was studied using the adsorbent particle flotation technique (APF and dissolved air flotation (DAF. A sample of an iron mineral was used as adsorbent particles of arsenic, ferric chloride as coagulant, cationic poly-acrylamide (NALCO 9808 as flocculants, and sodium oleate as collector. Adsorption studies to determine the pH influence, contact time, and adsorbent particles concentration on the adsorption of arsenic were carried out along with flotation studies to determine the removal efficiency of adsorbents particles. The results achieved indicate that the adsorption kinetic of arsenic is very rapid and that in range of pH’s from 2 to 7 the adsorption percentages remain constant. The equilibrium conditions were achieved in 60 minutes and about 95% of arsenic was adsorbed when used an adsorbent concentration of 2 g/L and pH 6.3. The maximum adsorption capacity of adsorbent particles was 4.96 mg/g. The mean free energy of adsorption (E was found to be 2.63 kJ/mol, which suggests physisorption. The results of the flotation studies demonstrated that when synthetic effluents with 8.9 mg/L of arsenic were treated under the following experimental conditions; 2 g/L of adsorbent particles, 120 mg/L of Fe(III, 2 mg/L of Nalco 9808, 20 mg/L of sodium oleate, and 40% of recycle ratio in the DAF, it was possible to reach 98% of arsenic removal and 6.3 NTU of residual turbidity in clarified synthetic effluent.

  20. Flotation separation of strontium via phosphate precipitation.

    Science.gov (United States)

    Thanh, Luong H V; Liu, J C

    2017-06-01

    Flotation separation of strontium (Sr) from wastewater via phosphate precipitation was investigated. While 37.33% of Sr precipitated at highly alkaline pH in the absence of PO 4 3- , it completely precipitated as Sr 3 (PO 4 ) 2 at a molar ratio ([PO 4 3- ]:[Sr 2+ ]) of 0.62 at a lower pH value. The presence of Ca 2+ hindered Sr precipitation, yet it could be overcome by increasing the PO 4 3- dose. Sodium dodecyl sulfate (SDS) was a better collector for dispersed air flotation of Sr 3 (PO 4 ) 2 than cetyl trimethyl ammonium bromide, or mixed collector systems of SDS and saponin. The highest separation efficiency of 97.5% was achieved at an SDS dose of 40 mg/L. The main mechanism in the precipitate flotation is adsorption of anionic SDS on the positively charged surface of colloidal Sr 3 (PO 4 ) 2 via electrostatic interaction. SDS enhanced the aggregation of Sr 3 (PO 4 ) 2 precipitates as the size increased from 1.65 to 28.0 μm, which was beneficial to separation as well.

  1. Flotation machine and process for removing impurities from coals

    Science.gov (United States)

    Szymocha, K.; Ignasiak, B.; Pawlak, W.; Kulik, C.; Lebowitz, H.E.

    1995-12-05

    The present invention is directed to a type of flotation machine that combines three separate operations in a single unit. The flotation machine is a hydraulic separator that is capable of reducing the pyrite and other mineral matter content of a coal. When the hydraulic separator is used with a flotation system, the pyrite and certain other mineral particles that may have been entrained by hydrodynamic forces associated with conventional flotation machines and/or by the attachment forces associated with the formation of microagglomerates are washed and separated from the coal. 4 figs.

  2. The Influence of Backwater Al3+ on Diaspore Bauxite Flotation

    Directory of Open Access Journals (Sweden)

    Chaojun Fang

    2017-10-01

    Full Text Available The effect of Al3+ in backwater on the flotation of diaspore bauxite was investigated by micro-flotation tests and the underlying mechanisms were investigated by inductively coupled plasma (ICP measurement, zeta potential measurements, solution chemistry analyses, and synchrotron near edge X-ray absorption fine structure (NEXAFS analyses. The ICP measurement results show the concentration of Al3+ in backwater was up to 1 × 10−4 mol/L. The micro-flotation results indicated that backwater Al3+ reduced the flotation recovery of diaspore and improved the flotation recovery of kaolinite at pH 9, which was the pH value used in the industrial flotation. The adsorption of Al3+ species changed the zeta potential, the Al atomic abundance, and the number of active sites on the mineral surface. In particular, the result of solution chemistry analyses and synchrotron NEXAFS analyses show that the Al3+ in backwater was adsorbed on the mineral surface in the form of Al(OH3 (s, and the bond of –Al–O–Al–(OH2 or –Al/Si–O–Al–(OH2 was formed at pH 9. It changed the intensity of hydrogen bond force between minerals and collectors, and resulted in the depression of diaspore flotation and the activation of kaolinite flotation. This study can be used to guide the application of backwater in the flotation of diaspore bauxite in industry.

  3. Influence of agitation intensity on flotation rate of apatite particles

    Directory of Open Access Journals (Sweden)

    Francisco Gregianin Testa

    Full Text Available Abstract The agitation intensity has a directly influence on flotation performance, lifting the particles and promoting the contact of bubbles and particles. In this paper, the energy input by the agitation on apatite flotation was investigated. The influence of pulp agitation in the flotation rate of particles with different sizes and two dosage levels was evaluated by batch testing. The flotation tests were conducted in an oscillating grid flotation cell (OGC, developed to promote a near isotropic turbulence environment. The cell is able to control the intensity of agitation and measure the energy transferred to the pulp phase. A sample of pure apatite was crushed (P80=310µm, characterized and floated with sodium oleate as collector. Four levels of energy dissipation, from 0.1 to 2 kWm-3, and two levels of collector dosage are used during the tests. The flotation kinetics by particle size were determined in function of the energy transferred. The results show a strong influence of the agitation intensity on the apatite flotation rate with both low and high dosage. For fine particles, when increasing the energy input, the flotation rate increase too, and this fact can be attributed to elevation of bubble-particle collisions. The kinetic result for the coarse particles demonstrated a reduction of the flotation rate whenever the energy input for this particle size was increased, whereby the turbulence caused by the agitation promotes the detachment of bubble-particle.

  4. Separation of oily materials in radioactive waste waters by flotation. Flotation kinetics

    International Nuclear Information System (INIS)

    Flores E, R.M.; Ortiz O, H.B.

    2003-01-01

    The rate of separation of oil and total cobalt in the oleaginous residual water previously treated by coagulation/flocculation with a quaternary ammonium amine (25 mgL -1 ) and with modified anionic polyacrylamide (1.5 mgL -1 ) (pH = 7, G 1 = 300 s -1 and G 2 = 30 s -1 ) was determined. The experimental essays to determine the flotation kinetics, its were carried out using as operation and control parameters the air/solids relationship (G/S 0.35), pressure (P =620 kPa) and volume of air-water mixture (V = 37% of V f ), obtained in previous essays, at two different pressure levels and volume of discharged mixture. The kinetic studies of flotation obtained for the flotation system with conventional air dissolved (DAF) its suggest a first order kinetics that it can be represented by the SCC model. At the same time its show that the separation of the present pollutants in the residual water is governed by the removal velocity of the oil. Meanwhile, the concentration of total Co below 1 mgL -1 , on the other hand, the concentration of the 60 Co at the end of the flotation process resulted smaller than 0.008 Bq/ml, as long as the one 54 Mn were not detectable. (Author)

  5. Development of zero conditioning procedure for coal reverse flotation

    Energy Technology Data Exchange (ETDEWEB)

    D.P. Patil; J.S. Laskowski [University of British Columbia, Vancouver, BC (Canada). Mining Engineering Department

    2008-04-15

    The zero conditioning method was developed to facilitate the flotation of gangue minerals in the reverse coal flotation process. Batch and continuous methods were developed to maintain the zero conditioning principle during reverse flotation. Batch zero conditioning was achieved by adding the required amount of DTAB in one step, as soon as the air was introduced into the system. The continuous zero conditioning method involves uninterrupted addition of DTAB through a specially built sparger in the form of aerosol during the flotation experiment. This produces active bubbles that carry collector. The addition of DTAB in the form of aerosol during reverse flotation proved to be better in reducing the ash of a sub-bituminous (LS-26) coal from 34.7% to 22.9% with a froth product (gangue) yield of 36.8% without any depressant. In the presence of coal depressant (dextrin, 0.5 kg/t), the ash content of LS-26 coal was reduced from 34.7% to 16.5% at a clean coal yield of 55%, whereas the conventional (forward) flotation with fuel oil provided a clean coal containing 16.5% ash with only 29.2% yield. These results prove that flotation of gangue minerals is very much improved by maintaining zero conditioning time conditions in a coal reverse flotation process.

  6. Selective separation of fine particles by a new flotation approach

    NARCIS (Netherlands)

    Mulleneers, H.A.E.; Koopal, L.K.; Bruning, H.; Rulkens, W.H.

    2002-01-01

    Fine particles often create problems in flotation applications. In this article a new laboratory flotation system for the selective separation of small particles was designed and tested. The device contains an active counter current sedimentation that should prevent entrainment of the fine

  7. Characterization and dewatering of flotation technological tailings

    Directory of Open Access Journals (Sweden)

    Grigorova I.

    2014-01-01

    Full Text Available The treatment of flotation tailings is today a subject of interest in mineral processing because of the potential of wasted materials as an actual mineral resource and because of environmental reasons. Decantation ponds are found at almost every mine in the world. They are large earth fill dams containing the residue of the milling process to extract metals from mined ores. Traditional wet tailings disposal has been problematic due to the risk of ground water contamination and the difficulty in rehabilitating storage sites. Tailings dams are at risk of failure due to leakage, instability, liquefaction, and poor design. In the last few years the use of paste technology in the disposal of mine tailings is increasingly studied as an option to conventional tailings dams. The Lucky Invest Concentrator is located in the Eastern Rhodopes Mountain of Bulgaria. Since 1959 lead-zinc ores are dressed. Finally, during the flotation cycle lead and zinc concentrates are produced. The final technological processing waste precipitates in tailing pond. Research and development program has started to established opportunities to obtain dry deposit of the ore processing residue and analyses the feature of new tailing disposal method. The tailings particle size distributions and chemical compositions were determined. The data from laboratory and pilot scale tests clearly illustrate that there are the possibilities to obtaine lead-zinc dewatered tailings. The experimental results show that new cyclone modifications have a potential in dewatering technology of flotation tailings. It appears that dewatering cyclones can be an approach on new tailings pond elimination technology.

  8. Immersion Suit Flotation Testing REACT Report

    Science.gov (United States)

    2016-08-01

    flotation after a two-week period. 1 CG-ENG-4 email, 11 Apr 16 2 46CFR160.171-11. Immersion...right side B‐Leveled out again 16‐Jun‐16 0730 KT E 2 5‐6 8 7‐1/2 8 8 No notable changes 16‐Jun‐16 1400 KT NE barely  breezy 2‐3 8 8 8 8 A‐Still greatly

  9. The sensitivity of direct faecal examination, direct faecal flotation, modified centrifugal faecal flotation and centrifugal sedimentation/flotation in the diagnosis of canine spirocercosis

    Directory of Open Access Journals (Sweden)

    J. Christie

    2011-04-01

    Full Text Available Several faecal examination techniques have shown variable sensitivity in demonstrating Spirocerca lupi (S. lupi eggs. The objective of this study was to determine which faecal examination technique, including a novel modified centrifugal flotation technique, was most sensitive to diagnose spirocercosis. Ten coproscopic examinations were performed on faeces collected from 33 dogs confirmed endoscopically to have spirocercosis. The tests included a direct faecal examination, a faecal sedimentation/flotation test, 4 direct faecal flotations and 4 modified faecal centrifugal flotations. These latter 2 flotation tests utilised 4 different faecal flotation solutions:NaNO3 (SG 1.22,MgSO4 (SG 1.29,ZnSO4 (SG 1.30 and sugar (SG 1.27. The sensitivity of the tests ranged between 42 %and 67 %, with theNaNO3 solution showing the highest sensitivity in both the direct and modified-centrifugal flotations. The modified NaNO3 centrifugal method ranked 1st with the highest mean egg count (45.24±83, and was superior (i.e. higher egg count and significantly different (P< 0.05 compared with the routine saturated sugar,ZnSO4 andMgSO4 flotation methods. The routine NaNO3 flotation method was also superior and significantly different (P < 0.05 compared with the routine ZnSO4 andMgSO4 flotation methods. Fifteen per cent (n=5 of dogs had neoplastic oesophageal nodules and a further 18 % (n = 6 had both neoplastic and non-neoplastic nodules. S. lupi eggs were demonstrated in 40%of dogs with neoplastic nodules only and 72.9 % of the dogs with non-neoplastic nodules. The mean egg count in the non-neoplastic group (61 was statistically greater (P = 0.02 than that of the neoplastic group (1. The results show that faecal examination using a NaNO3 solution is the most sensitive in the diagnosis of spirocercosis. The modified centrifugal flotation faecal method using this solution has the highest egg count. The study also found that dogs with neoplastic nodules shed

  10. Concentration of uranium in seawater by flotation

    International Nuclear Information System (INIS)

    Nozaki, Toru; Yamashita, Hiroshi

    1986-01-01

    A method has been developed for the concentration of uranium in seawater by precipitation flotation-carbonate extraction-ion flotation. Uranium in seawater was coprecipitated with hydrated iron (III) oxide by adjusting the pH to 5.5 after addition of 1.0 x 10 -3 mol/l of iron (III) and agitating for 1 hr, and the precipitate was floated with 1.0 x 10 -5 mol/l of sodium oleate and 5.0 x 10 -5 mol/l of sodium lauryl sulfate by bubbling nitrogen through the seawater for 15 min. Uranium was extracted from the precipitate scum at the yield of 89 % with 100 ml of 1.8 % of ammonium carbonate solution by agitating for 2 hr, and floated with 1.2 x 10 -3 mol/l of cetylpyridinium chloride by bubbling nitrogen through the extract diluted 5-fold for 30 min in the recovery of about 100 %. The fairly selective recovery of uranium was obtained from 4 l of seawater at the yield of 87 % throughout the entire process. (author)

  11. Kaolinite removal from bauxite by flotation

    Directory of Open Access Journals (Sweden)

    Otávia Martins Silva Rodrigues

    Full Text Available Abstract This paper presents a potential condition to separate kaolinite through flotation when it is present in bauxite ore. This research anticipates a Brazilian industry requirement, considering the tendency towards the need for aluminosilicates removal from bauxite ores, as has already occurred in China. Kaolinite is the most abundant aluminosilicate, and gibbsite is the main aluminum bearing mineral in Brazilian bauxite ores. The first step was a fundamental study involving microflotation experiments with pure samples of kaolinite and gibbsite. Ammonium quaternary salts and amines were used as the collector and corn starch as the depressant. In a fundamental study, the best conditions determined in the first step were evaluated for the flotation of kaolinite from bauxite ore using laboratory scale experiments. Tests with AQ142/starch (pH 10 and CTAB (pH 7 led to satisfactory results. In general, the highest values of alumina/silica mass ratio were obtained with AQ142/starch and the highest values of mass recovery and metallurgical recovery were achieved with CTAB.

  12. Highly Polluted Wastewaters Treatment by Improved Dissolved Air Flotation Technology

    Science.gov (United States)

    Moga, I. C.; Covaliu, C. I.; Matache, M. G.; Doroftei, B. I.

    2017-06-01

    Numerous investigations are oriented towards the development of new wastewater treatment technologies, having high efficiencies for removing even low concentrations of pollutants found in water. These efforts were determined by the destroyer impact of the pollutants to the environment and human’s health. For this reason this paper presents our study concerning an improved dissolved air flotation technology for wastewater treatment. There is described a dissolved air flotation (DAF) installation composed by two equipments: pressurized capsule and lamellar settling. Also, there are presented some advantages of using nanoparticles as flotation collectors.

  13. Swimming kinematic and flotation analysis of conscious and sedated dogs using 3 canine flotation devices.

    Science.gov (United States)

    Corum, China Prentice; Wichtowski, Maja; Hetts, Suzanne; Estep, Dan; Bertone, Joseph J

    2014-12-01

    Canine flotation devices (CFDs) are very popular; however, their efficacy is still under debate. There is no oversight to standardize device testing, certification, or qualification for use. We set out to assess the biomechanical and behavioral effects of 3 CFDs on swim and flotation characteristics of dogs. High-speed video recordings were used to measure behavior, range of motion (ROM), maximum flexion angle, and cycles of motion per minute while swimming and roll, yaw, and fear or panic scoring while floating. Predictably, swimming with no CFD yielded the largest ROM and flexion angles. CFDINF was associated with the least ROM. During flotation, CFDAB and CFDRW caused significant rolling and fear, whereas CFDINF was the most stable. CFDAB was associated with cranial downpitch in 2 dogs. Interpretation of the kinematics for CFDAB and CFDRW suggests that decreased stability in the water leads to a greater forced ROM when the position of the dog was conducive to swimming. When positioning forced the dog into a downward pitch, ROM was decreased because of the increased effort for the dogs to keep their head above water. CFDINF was most stable overall owing to a decreased swim effort, with most dogs showing the lowest fear scores and absolute relaxation. CFDAB and CFDRW caused the dogs significant rolling, fear, and distress, with obvious fighting of sedation. We hope to disseminate these results to dog owners in the hopes of providing a valid assessment of these devices. Copyright © 2014 Elsevier Inc. All rights reserved.

  14. Treatment of oily water by flotation

    International Nuclear Information System (INIS)

    Ortiz O, H.B.

    2002-01-01

    The operation of the nuclear power plants such as Laguna Verde (CLV) with nuclear reactors of the boiling water type (BWR) produce radioactive waste solids, liquids and gaseous which require of a special treatment in their operation and arrangement. Such is the case of the liquid wastes from CLV which are a mixture of water and synthetic oils coming from leaks and spilling by pressure of maintenance of electro-mechanical equipment associated to the performance of the nuclear power plant. This mixture of water and spent oils is pretreated by means of sedimentation, centrifugation and evaporation. However the realized efforts by the CLV, the spent oil obtained from the pretreatment contains concentrations of radioactive material higher than the tolerance limits established in the normative in force in radiological safety (0.37 Bq m L -1 for 60 Co and 54 Mn). In this context it was necessary to design an efficient treatment system and economically profitable which separates the oil, the heavy metals and the leftovers of radioactive material that could be present in water, with the purpose of fulfil with the Mexican Official Standards corresponding for its unload or even it can reuse it in the wash process of treated oil. The treatment system of oily water waste consists of: a) Coagulation-flocculation, b) Flotation system with modified air dissolved (DAFm). The proposed flotation process allows to reach a higher separation efficiencies of: Concentration of greases and oils: 94.11 %; Turbidity: 98.6 %; 60 Co: 82.3 % ; Co: 94.8 % and Cr: 99.9 % (Author)

  15. Raman spectroscopic study of some chalcopyrite-xanthate flotation products

    CSIR Research Space (South Africa)

    Andreev, GN

    2003-12-16

    Full Text Available of normal vibrations of the corresponding individual compounds. The latter facilitated the Raman spectroscopic elucidation of the reaction products formed on the chalcopyrite surface in real industrial flotation conditions with a sodium isopropyl xanthate...

  16. A study of the flotation of oxidized Amasra Coal

    Energy Technology Data Exchange (ETDEWEB)

    Karsilayan, H.; Afsar, I.; Yanic, C.; Yilmaz, N. (Yildiz University, Istanbul (Turkey). Dept. of Chemistry)

    1992-01-01

    The flotation of oxidized Amasra Coal which was collected between 1973-1978 and stored under atmospheric conditions was examined in this work. Coal samples were fractioned by wet screening to [plus]0.560 mm, -0.560 [plus]0.140 mm, [minus]0.140 mm particle sizes and first fraction was ground to -0.560 mm before flotation. Motorin and pine oil which had been heated at 125[degree]C for 5 hours were used as flotation reagents. The influence of impeller speed, aeration rate, solid content of the pulp, reagent amounts were examined and optimum values were determined. Increase of the pine oil amount added to the pulp, increased the coal recovery on the flotation of this oxidized coal. 10 refs., 10 tabs.

  17. Coal desulfurization by bacterial treatment and column flotation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kawatra, S.K. [Michigan Technological Univ., Houghton, MI (United States)

    1994-06-01

    A review of the literature showed that bacterial leaching, using the microorganism Thiobacillus ferrooxidans, was a very effective technique for removing pyrite from coal, as it could dissolve even the finest pyrite particles without the need for expensive reagents or extreme processing conditions. Unfortunately, bacterial leaching is also rather slow, and so the initial goal of this research was to decrease the leaching time as much as possible. However, this still left the bacteria needing approximately a week to remove half of the pyritic sulfur, and so a faster technique was sought. Since it had been reported in the literature that T. ferrooxidans could be used to depress the flotation of pyrite during froth flotation of coal, this was investigated further. By studying the recovery mechanisms of coal-pyrite in froth flotation, it was found that pyrite was being recovered by entrainment and by locking to coal particles, not by true flotation of hydrophobic pyrite. Therefore, no pyrite depressant could be of any significant benefit for keeping pyrite out of the coal froth product, and it was much more important to prevent entrainment from occurring. Countercurrent flotation columns were invented to essentially eliminate entrainment effects, by washing the froth and reducing mixing of the froth and tailings products. Existing flotation columns tend to be quite simple, and in order to give reasonable product quality they must be very tall (typically 30--45 feet). As a result, they have difficulty in handling the high froth volumes which occur in coal flotation, and are awkward to install in existing plants. The bulk of this project therefore concentrated on developing an improved coal flotation column, and testing it under actual plant conditions.

  18. Human body flotation and organic responses to water immersion

    OpenAIRE

    Llana Belloch, Salvador; Lucas Cuevas, Angel Gabriel; Pérez Soriano, Pedro; Priego Quesada, José Ignacio

    2013-01-01

    Swimming is a physical activity performed in an environment where human beings are not adapted from an evolutionary point of view. For this reason, swimming for humans is considered an ontogenetic movement and not a phylogenetic one such as walking or running on land. Locomotion into the water has some very specific characteristics for the human being, since the body experiences a situation of hydrostatic microgravity which in most cases enables flotation. Flotation capacity is affected by th...

  19. Boiling treatment of ABS and PS plastics for flotation separation.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Wu, Bao-xin; Liu, Qun

    2014-07-01

    A new physical method, namely boiling treatment, was developed to aid flotation separation of acrylonitrile-butadiene-styrene (ABS) and polystyrene (PS) plastics. Boiling treatment was shown to be effective in producing a hydrophilic surface on ABS plastic. Fourier Transform Infrared analysis was conducted to investigate the mechanism of boiling treatment of ABS. Surface rearrangement of polymer may be responsible for surface change of boiling treated ABS, and the selective influence of boiling treatment on the floatability of boiling treated plastics may be attributed to the difference in the molecular mobility of polymer chains. The effects of flotation time, frother concentration and particle size on flotation behavior of simple plastic were investigated. Based on flotation behavior of simple plastic, flotation separation of boiling treatment ABS and PS with different particle sizes was achieved efficiently. The purity of ABS and PS was up to 99.78% and 95.80%, respectively; the recovery of ABS and PS was up to 95.81% and 99.82%, respectively. Boiling treatment promotes the industrial application of plastics flotation and facilitates plastic recycling. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Interfacial interactions between plastic particles in plastics flotation.

    Science.gov (United States)

    Wang, Chong-qing; Wang, Hui; Gu, Guo-hua; Fu, Jian-gang; Lin, Qing-quan; Liu, You-nian

    2015-12-01

    Plastics flotation used for recycling of plastic wastes receives increasing attention for its industrial application. In order to study the mechanism of plastics flotation, the interfacial interactions between plastic particles in flotation system were investigated through calculation of Lifshitz-van der Waals (LW) function, Lewis acid-base (AB) Gibbs function, and the extended Derjaguin-Landau-Verwey-Overbeek potential energy profiles. The results showed that van der Waals force between plastic particles is attraction force in flotation system. The large hydrophobic attraction, caused by the AB Gibbs function, is the dominant interparticle force. Wetting agents present significant effects on the interfacial interactions between plastic particles. It is found that adsorption of wetting agents promotes dispersion of plastic particles and decreases the floatability. Pneumatic flotation may improve the recovery and purity of separated plastics through selective adsorption of wetting agents on plastic surface. The relationships between hydrophobic attraction and surface properties were also examined. It is revealed that there exists a three-order polynomial relationship between the AB Gibbs function and Lewis base component. Our finding provides some insights into mechanism of plastics flotation. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Optimizing dissolved air flotation design system

    Directory of Open Access Journals (Sweden)

    L.A. Féris

    2000-12-01

    Full Text Available Dissolved Air (Pressure Flotation-DAF, is a well-established separation process that employs micro-bubbles as a carrier phase. This work shows results concerning bubble generation at low working pressures in modified DAF-units to improve the collection of fragile coagula by bubbles. DAF of Fe (OH3 (as model was studied as a function of saturation pressure in the absence and presence of surfactants in the saturator. DAF was possible at 2 atm by lowering the air/water surface tension. This fact, which leads to substantial energy savings, was explained in terms of decreasing the "minimum" energy required for bubble nucleation and cavity in the nozzle. More, bubbles-fragile coagula attachment was improved by dividing the recycling water into two: 1 the inclined inlet to the cell (traditional and 2 inside the separation tank through a water flow inlet situated below the floating bed using a "mushroom" type diffuser. Because of the reduction observed in the degree of turbulence in the conventional collection zone, DAF performance improved yielding high precipitate recoveries.

  2. Flocculation of flotation tailings using thermosensitive polymers

    Directory of Open Access Journals (Sweden)

    Bogacz Wojciech

    2017-09-01

    Full Text Available The key feature of thermosensitive polymers is the reversible transition between the hydrophilic and hydrophopic forms depending on the temperature. Although the main research efforts are focused on their application in different kinds of drug delivery systems, this phenomenon also allows one to precisely control the stability of solid-liquid dispersions. In this paper research on the application of poly(N-isopropylacrylamide copolymers in processing of minerals is presented. In the experiments tailings from flotation plant of one of the coal mines of Jastrzębska Spółka Węglowa S.A. (Poland were used. A laser particle sizer Fritsch Analysette 22 was used in order to determine the Particle Size Distribution (PSD. It was proved that there are some substantial issues associated with the application of thermosensitive polymers in industrial practice which may exclude them from the common application. High salinity of suspension altered the value of Lower Critical Solution Temperature (LCST. Moreover, the co-polymers used in research proved to be efficient flocculating agents without any temperature rise. Finally, the dosage needed to achieve steric stabilization of suspension was greatly beyond economic justification.

  3. Effects of Flotation-REST on Muscle Tension Pain

    Directory of Open Access Journals (Sweden)

    Anette Kjellgren

    2001-01-01

    Full Text Available The purpose of the present study was to investigate whether the floating form of the restricted environmental stimulation technique (REST may be applied within the field of pain relief. Flotation-REST consists of a procedure whereby an individual is immersed in a tank filled with water of an extremely high salt concentration. Thirty-seven patients (14 men and 23 women suffering from chronic pain consisting of aching muscles in the neck and back area participated in the study. They were randomly assigned to either a control group (17 participants or an experimental group (20 participants. The experimental group received nine opportunities to use the flotation-REST technique in the water tank over a three-week period. The results indicated that the most severe perceived pain intensity was significantly reduced, whereas low perceived pain intensity was not influenced by the floating technique. Further, the results indicated that circulating levels of the noradrenaline metabolite 3-methoxy-4-hydroxyphenylethyleneglycol were reduced significantly in the experimental group but not in the control group following treatment, whereas endorphin levels were not affected by flotation. Flotation-REST treatment also elevated the participants' optimism and reduced the degree of anxiety or depression; at nighttime, patients who underwent flotation fell asleep more easily. The present findings describe possible changes, for the better, in patients presenting with chronic pain complaints.

  4. Immobilization of copper flotation waste using red mud and clinoptilolite.

    Science.gov (United States)

    Coruh, Semra

    2008-10-01

    The flash smelting process has been used in the copper industry for a number of years and has replaced most of the reverberatory applications, known as conventional copper smelting processes. Copper smelters produce large amounts of copper slag or copper flotation waste and the dumping of these quantities of copper slag causes economic, environmental and space problems. The aim of this study was to perform a laboratory investigation to assess the feasibility of immobilizing the heavy metals contained in copper flotation waste. For this purpose, samples of copper flotation waste were immobilized with relatively small proportions of red mud and large proportions of clinoptilolite. The results of laboratory leaching demonstrate that addition of red mud and clinoptilolite to the copper flotation waste drastically reduced the heavy metal content in the effluent and the red mud performed better than clinoptilolite. This study also compared the leaching behaviour of metals in copper flotation waste by short-time extraction tests such as the toxicity characteristic leaching procedure (TCLP), deionized water (DI) and field leach test (FLT). The results of leach tests showed that the results of the FLT and DI methods were close and generally lower than those of the TCLP methods.

  5. Multi-Stage Flotation for the Removal of Ash from Fine Graphite Using Mechanical and Centrifugal Forces

    Directory of Open Access Journals (Sweden)

    Xiangning Bu

    2018-01-01

    Full Text Available Graphite ore collected from Hunan province, south China was characterized by chemical analysis, X-ray diffraction, and optical microscopy. Rougher and multi-stage flotation tests using a mechanical flotation cell and a flotation column containing an additional centrifugal force field were carried out to promote its grade and economic value. In rougher flotation, both the mechanical flotation cell and flotation column reduced the ash content of the graphite ore from 15.43% to 10.8%, while the yield of the flotation column (91.41% was much higher than that of the mechanical flotation cell (50%. In the presence of hydrophobic graphite, the seriously entrained gangue restricted further improvement in the quality and economic value of the graphite ore. Therefore, multi-stage flotation circuits were employed to diminish this entrainment. Multi-stage flotation circuits using the two flotation devices further decreased the ash content of the graphite ore to ~8%, while the yield when using the flotation column was much higher than that obtained from the mechanical flotation cell employed. On the other hand, the ash removal efficiency of the flotation column was 3.82-fold higher than that observed for the mechanical flotation cell. The Cleaner 3 flotation circuit using the flotation column decreased the ash content in graphite from 15.43% to 7.97% with a yield of 77.53%.

  6. Influence of some ions on the apatite flotation of Itataia ore

    International Nuclear Information System (INIS)

    Aquino, J.A. de.

    1987-01-01

    The production process by flotation for uranium phosphor ore in Itataia-Ce, Brazil is shown. A flotation scheme with mass balance and characterization on the samples is analyzed. The analysis methods with some results of concentration effect of Ca 2+ , Mg 2+ , Cl - e Na + in the direct flotation are demonstrated. (M.J.C.) [pt

  7. Evaluation of column flotation results with a film flotation method; Film fusenho wo mochiita column fusen kekkan no hyoka

    Energy Technology Data Exchange (ETDEWEB)

    Fujimoto, H.; Matsukata, M.; Ueyama, K. [Osaka University, Osaka (Japan). Faculty of Engineering Science

    1996-10-28

    Change in wettability of coal particle surfaces due to kerosene adsorption was studied by using a film flotation method. The applicability of a film flotation method to coals modified by kerosene adsorption was first confirmed. In experiment, film flotation was applied to Illinois coal modified by aqueous methanol solution and kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface and kerosene in aqueous methanol solution were analyzed to verify the applicability of a film flotation method. Film flotation was applied to Datong and Illinois coals modified by kerosene adsorption, and the weight percent of residual particles on a gas-liquid interface was plotted to surface tension of liquid. As a result, the weight percent of hydrophobic particles within 50mN/m in surface tension slightly increased in Datong coal and remarkably increased in Illinois coal with kerosene addition. It was thus suggested that in addition to surface tension, the distributions of hydrophilic and hydrophobic strengths on the surface of each coal particle should be considered to understand attachment of coal particles and bubbles. 6 refs., 4 figs.

  8. Intensification of the Reverse Cationic Flotation of Hematite Ores with Optimization of Process and Hydrodynamic Parameters of Flotation Cell

    Science.gov (United States)

    Poperechnikova, O. Yu; Filippov, L. O.; Shumskaya, E. N.; Filippova, I. V.

    2017-07-01

    The demand of high grade iron ore concentrates is a major issue due to the depletion of rich iron-bearing ores and high competitiveness in the iron ore market. Iron ore production is forced out to upgrade flowsheets to decrease the silica content in the pelettes. Different types of ore have different mineral composition and texture-structural features which require different mineral processing methods and technologies. The paper presents a comparative study of the cationic and anionic flotation routes to process a fine-grain oxidized iron ore. The modified carboxymethyl cellulose was found as the most efficient depressant in reverse cationic flotation. The results of flotation optimization of hematite ores using matrix of second-order center rotatable uniform design allowed to define the collector concentration, impeller rotation speed and air flowrate as the main flotation parameters impacting on the iron ore concentrate quality and iron recovery in a laboratory flotation machine. These parameters have been selected as independent during the experiments.

  9. The flotation of gold, uranium, and pyrite from Witwatersrand ores

    International Nuclear Information System (INIS)

    Lloyd, P.J.D.

    1981-01-01

    The Witwatersrand reefs contain gold, uranium, and pyrite in the following average concentrations: 0,001 per cent, 0,02 per cent, and 1,7 per cent respectively. The paper discusses the flotation of pyrite to produce a sulphide concentrate, reviews work done on the production of gold concentrates, discusses attempts to produce maximum concentrates, and closes with a review of processes for the simultaneous flotation of these three species. It is concluded that high recoveries of all three species can be achieved only if a rougher concentrate of perhaps 20 per cent of the feed (by mass) is produced, and it is suggested that reverse leaching (leaching before cyanidation) of this concentrate, followed by a cleaning flotation step for the recovery of the pyrite, would be more efficient than the routes employed at present [af

  10. Selective flotation of PVC using gelatin and lignin alkali.

    Science.gov (United States)

    Yenial, Unzile; Kangal, Olgaç; Güney, Ali

    2013-06-01

    Recycling has become one of the most important issues as a result of increasing waste mass in present day. This is especially important for polymer wastes as they are hard to degenerate in nature. Today, most of the practical methods used for the recycling of waste mass, such as hand sorting, gravity separation, etc., cannot be performed successfully owing to close densities of polymers. Froth flotation can be used successfully and economically for this purpose. The main objective of this study was to investigate the effect of plasticizer reagents and the success of froth flotation at plastic recycling. In this study, lignin alkali and gelatin were used as plasticizer reagents. The effect of these reagents was searched with the parameters of pH, concentration, conditioning and flotation time. In the case of post-consumed polyethylene terephthalate and polyvinyl chloride (PVC), 98.9% purity of PVC was obtained at optimum conditions.

  11. Removal of arsenic in flotation of galena and sphalerite

    Science.gov (United States)

    Yu, Dae-hwan; Kim, Min-kyu; Han, Oh-hyung; Park, Chul-hyun

    2017-04-01

    In Korea, Janggun mine that produces the concentrate of galena (PbS) /sphalerite (ZnS) containing arsenic of 1.3% charges a penalty of US 3/ton to LS-Nikko smelter. Hence in this work, flotation tests for removal of arsenopyrite (FeAsS) from sulfide minerals were carried out using lab scale flotation cell, which maintain grade and recovery of PbS and ZnS in comparison to flotation plant. Particularly, this study was focused on investigating the combination of several chemical reagents such as depressant, collector, activator and etc. that affect flotation performance. In the straight differential flotation for PbS, a PbS grade of 67.80% and a recovery of 80.2% could be obtained with FeAsS removal of 84.1% (0.2% As) under the conditions of 20% feed solids concentration, pH 8.5, 50g/t frother (AF65), 50g/t collector (AP242) and 600g/t As depressant (NaHSO3) and 600g/t Zn depressant (ZnSO4). In the ZnS flotation, the maximum separation achievable for ZnS has been shown to be a grade of 50.27% and a recovery of 88.7%. At this time, FeAsS removal of 87.8% (0.16% As) could be successfully accomplished under pH 11, and 1.2kg/t Zn activator (CuSO4), 100g/t frother (AF65), 100g/t collector (AP211) and 400g/t As depressant (NaHSO3). Acknowledgments This work was supported by the Energy and Resources Engineering Program Grant funded by the Ministry of Trade, Industry and Energy, Korea

  12. Flotation thermodynamics: Can we learn anything from it?

    Energy Technology Data Exchange (ETDEWEB)

    Laskowski, J.S. [University of British Columbia, Vancouver, BC (Canada). Dept. of Mining Engineering

    2007-07-15

    The role of bubbles in the transportation of hydrophobic particles to a froth phase in flotation is well established. However, analysis of available data reveals that the bubbles are important most of all because they are the primary means of transportation of flotation agents to the points of bubble-to-particle attachment. The common view is that bubbles attach and lift hydrophobic particles to a froth layer. The thermodynamic analysis presented in this paper also leads to the conclusion that also the particles which become hydrophobic during the particle-bubble collision and attachment can be captivated by bubbles.

  13. CHAIN EXTENDER AND EMULSIFIER APPLICATION IN IRON ORE FLOTATION

    Directory of Open Access Journals (Sweden)

    José Pedro da Silva

    2013-06-01

    Full Text Available The present study aims to evaluate the reverse flotation performance of iron ore, using collector (amine, in the presence and absence of chain extender (diesel oil and emulsifier (sodium lauryl sulfate.Six tests were realized with duplicate. Tests using amine, diesel oil and sodium lauryl sulphate show the better results, with metallurgical recovery of 91.82% and the concentrate silica equal 1.68%. Thus, it is found that the use of emulsifier and chain extender together with the amine, shows better results in the flotation, in terms of metal recovery and selectivity, when compared to using only amine or amine and diesel oil.

  14. Method for enhancing selectivity and recovery in the fractional flotation of particles in a flotation column

    Science.gov (United States)

    Klunder, Edgar B [Bethel Park, PA

    2011-08-09

    The method relates to particle separation from a feed stream. The feed stream is injected directly into the froth zone of a vertical flotation column in the presence of a counter-current reflux stream. A froth breaker generates a reflux stream and a concentrate stream, and the reflux stream is injected into the froth zone to mix with the interstitial liquid between bubbles in the froth zone. Counter-current flow between the plurality of bubbles and the interstitial liquid facilitates the attachment of higher hydrophobicity particles to bubble surfaces as lower hydrophobicity particles detach. The height of the feed stream injection and the reflux ratio may be varied in order to optimize the concentrate or tailing stream recoveries desired based on existing operating conditions.

  15. Chemical and colloidal aspects of collectorless flotation behavior of sulfide and non-sulfide minerals.

    Science.gov (United States)

    Aghazadeh, Sajjad; Mousavinezhad, Seyed Kamal; Gharabaghi, Mahdi

    2015-11-01

    Flotation has been widely used for separation of valuable minerals from gangues based on their surface characterizations and differences in hydrophobicity on mineral surfaces. As hydrophobicity of minerals widely differs from each other, their separation by flotation will become easier. Collectors are chemical materials which are supposed to make selectively valuable minerals hydrophobic. In addition, there are some minerals which based on their surface and structural features are intrinsically hydrophobic. However, their hydrophobicities are not strong enough to be floatable in the flotation cell without collectors such as sulfide minerals, coal, stibnite, and so forth. To float these minerals in a flotation cell, their hydrophobicity should be increased in specific conditions. Various parameters including pH, Eh, size distribution, mill types, mineral types, ore characterization, and type of reaction in flotation cells affect the hydrophobicity of minerals. Surface analysis results show that when sulfide minerals experience specific flotation conditions, the reactions on the surface of these minerals increase the amount of sulfur on the surface. These phenomenons improve the hydrophobicity of these minerals due to strong hydrophobic feature of sulfurs. Collectorless flotation reduces chemical material consumption amount, increases flotation selectivity (grade increases), and affects the equipment quantities; however, it can also have negative effects. Some minerals with poor surface floatability can be increased by adding some ions to the flotation system. Depressing undesirable minerals in flotation is another application of collectorless flotation.

  16. Ionic flotation of uranium contained in industrial phosphoric acid

    International Nuclear Information System (INIS)

    Jdid; Blazy; Bessiere

    1983-01-01

    A new process for uranium recovery from industrial phosphoric acid at 30% of P 2 O 5 is applied by the ionic flotation process. Research is carried out on determination of the nature of ionic species of U in H 3 PO 4 5.5 M and the behavior of reagents from CECA Co. in very acid media. Reagents able to form complexes directly with uranium and stable in phosphoric acid selected are: potassium ethylene diamine tetra (methylene phosphonate) (INIPOL AD32) and sodium dialkyldiphosphonate (34S). Uranium IV, obtained by reduction of uranium VI with iron powder, is precipitated by these reagents. Flotation of the precipitate obtained with INIPOL AD 32 is realized by addition of hexylamino bis (methylene phosphonic acid). A recovery of 80 wt% is obtained. Flotation of the coprecipitate 34S-U(IV) is obtained without any other additions because 34S is a surfactant. Metal recovery is better than 90% and the coprecipitate contains more than 10% U. The process is fast precipitation 10 minutes and flotation 5 minutes and is efficient even at 60 0 C [fr

  17. resorcinol for flotation-spectrophotometric determination of iron

    African Journals Online (AJOL)

    2-pyridylazo)resorcinol (PAR) based on a 1:2 FeII-PAR complex were found to be as follows: flotation solvent (chloroform), shaking time (2 min), pH (4.5±0.5), concentration of PAR (2.0×10–4 mol L–1), reducing agent (hydroxylamine ...

  18. Beneficiation of Iranian magnesite ores by reverse flotation process ...

    Indian Academy of Sciences (India)

    Bricks and monolithic ramming mixes which were made from these aggregates were analysed and their mechanical and physical properties, studied. The results of this investigation showed that the application of reverse flotation process on the magnesite ore of eastern part of Iran causes an acceptable reduction on the ...

  19. Dissolved Air Flotation Process for Algae Removal | Mulaku ...

    African Journals Online (AJOL)

    This study investigated the performance of the Dissolved Air Flotation (DAF) process as an alternative to sedimentation for algae removal in surface water treatment in Kenya. Batch DAF experiments were carried out in the laboratory using algae laden surface water samples collected from the river and laboratory cultured ...

  20. Selective recovery of micrometer bioparticles using aggregation and air flotation

    NARCIS (Netherlands)

    Van Hee, P.

    2006-01-01

    Air flotation is a separation technique that makes use of the air-water interface for separation of particles and molecules from mixtures. This thesis discusses its use for separation of bioparticle mixtures. Particulate bioproducts, such as crystals, inclusion bodies, virus-like particles and

  1. Influence of attrition variables on iron ore flotation

    Directory of Open Access Journals (Sweden)

    Fabiana Fonseca Fortes

    Full Text Available Abstract The presence of slimes is harmful to the flotation process: the performance and consumption of reagents are negatively affected. Traditionally, the desliming stage has been responsible for removing slimes. However, depending on the porosity of the mineral particles, desliming may not be sufficient to maximize the concentration results. An attrition process before the desliming operation can improve the removal of slime, especially when slimes cover the surface and/or are confined to the cavities/pores of the mineral particles. Attrition is present in the flowcharts of the beneficiation process of phosphate and industrial sand (silica sand. Research has been undertaken for its application to produce pre-concentrates of zircon and iron ore. However, there is still little knowledge of the influence of the attrition variables on the beneficiation process of iron ore. This study presents a factorial design and analysis of the effects of these variables on the reverse flotation of iron ore. The standard of the experimental procedures for all tests included the attrition of pulp, under the conditions of dispersion, desliming and flotation. The parameter analysed (variable response was the metallurgical recovery in reverse flotation tests. The planning and analysis of the full factorial experiment indicated that with 95% reliability, the rotation speed of the attrition cell impeller was the main variable in the attrition process of the iron ore. The percentage of solid variables in the pulp and the time of the attrition, as well as their interactions, were not indicated to be significant.

  2. Flotation and remediation of contaminated sludge and soil

    NARCIS (Netherlands)

    Koopal, L.K.; Mulleneers, H.A.E.

    2003-01-01

    Flotation, traditionally applied in mineralogy, has been used more recently in wastewater treatment, soil and sediment remediation and paper de-inking. The latter types of application may differ from mineral separation by the fact that the particles that should be floated are often partially

  3. Drainage and fractionation of wood fibers in a flotation froth

    Science.gov (United States)

    J.Y. Zhu; Freya Tan

    2005-01-01

    Understanding fiber fractionation in a froth is very important to the quality of recovered fibers in flotation deinking operations. Fiber length is a very important fiber quality parameter in paper-making. For example, long fibers tend to produce a paper with higher tear strength than short fibers. In this study, fibers in froth collected at different froth drainage...

  4. Flotation mechanisms of molybdenite fines by neutral oils

    Science.gov (United States)

    Lin, Qing-quan; Gu, Guo-hua; Wang, Hui; Liu, You-cai; Fu, Jian-gang; Wang, Chong-qing

    2018-01-01

    The flotation mechanisms of molybdenite fines by neutral oils were investigated through microflotation test, turbidity measurements, infrared spectroscopy, and interfacial interaction calculations. The results of the flotation test show that at pH 2-11, the floatability of molybdenite fines in the presence of transformer oil is markedly better than that in the presence of kerosene and diesel oil. The addition of transformer oil, which enhances the floatability of molybdenite fines, promotes the aggregation of molybdenite particles. Fourier transform infrared measurements illustrate that physical interaction dominates the adsorption mechanism of neutral oil on molybdenite. Interfacial interaction calculations indicate that hydrophobic attraction is the crucial force that acts among the oil collector, water, and molybdenite. Strong hydrophobic attraction between the oily collector and water provides the strong dispersion capability of the collector in water. Furthermore, the dispersion capability of the collector, not the interaction strength between the oily collectors and molybdenite, has a highly significant role in the flotation system of molybdenite fines. Our findings provide insights into the mechanism of molybdenite flotation.

  5. Method and apparatus for production of subsea hydrocarbon formations

    Science.gov (United States)

    Blandford, J.W.

    1995-01-17

    A system for controlling, separating, processing and exporting well fluids produced from subsea hydrocarbon formations is disclosed. The subsea well tender system includes a surface buoy supporting one or more decks above the water surface for accommodating equipment to process oil, gas and water recovered from the subsea hydrocarbon formation. The surface buoy includes a surface-piercing central flotation column connected to one or more external flotation tanks located below the water surface. The surface buoy is secured to the sea bed by one or more tendons which are anchored to a foundation with piles imbedded in the sea bed. The system accommodates multiple versions on the surface buoy configuration. 20 figures.

  6. Study on the flotation technology for deep-cleaning of coal slime

    Energy Technology Data Exchange (ETDEWEB)

    Fu Xiao-heng; Shan Xiao-yun; Jiang He-jin; Li Xiang-li [China University of Mining and Technology, Beijing (China). School of Chemical and Environmental Engineering

    2006-07-01

    The paper introduced the basic principle and special features of deep-cleaning of coal slime by flotation, first, separating the slime by conventional flotation to give a relatively low ash concentrate, a tailing containing an ash as high as possible, followed by flocculation-flotation to recover additional low ash concentrate. The regressive release flotation test and microphoto indicated that the middling consists mainly of intergrowth particles of coal and minerals. Comparison between deep-cleaning and conventional flotation results denoted that, at approximately same concentrate ash, its yield by deep-cleaning was 46.06 percent point higher, and at similar yield, its concentrate ash, 1.78 percent point lower. The performance by deep-cleaning is even better than that by regressive release flotation test. 4 refs., 2 figs., 6 tabs.

  7. Coal-oil gold agglomeration assisted flotation to recover gold from refractory ore

    Science.gov (United States)

    Otsuki, A.; Yue, C.

    2017-07-01

    This study aimed to investigate the applicability of coal-oil gold agglomeration (CGA) assisted flotation to recover gold from a refractory ore. The ore with the grade of 2-5 g/t was tested with the CGA-flotation process in six different size fractions from 38 to 300 urn using different collector types and dosages. In addition, the flotation without CGA was performed under the same condition for comparison. The results showed that the higher gold grade and recovery were achieved by applying the CGA-flotation, compared with the flotation without CGA. More than 20-60 times grade increase from the head grade was obtained with CGA-flotation. The elemental analysis of gold and sulphur explained their relationship with gold recovery. The results well indicated the applicability of CGA to upgrade the refractory gold ore.

  8. In-plant testing of microbubble column flotation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, R.H.; Luttrell, G.H.; Adel, G.T.; Mankosa, M.J.

    1991-07-31

    Microbubble column flotation (MCF) was developed at the Virginia Center for Coal and Minerals Processing (VCCMP) for the selective recovery of fine particles. Bench-scale test work conducted at VCCMP, largely under the sponsorship of the U.S. Department of Energy (DOE), showed that the technology worked well for both coal and mineral applications. For the technology to be commercially successful, however, a full-scale demonstration of the MCF technology was deemed necessary. This report summarizes the results of work performed under the DOE project entitled ``In-plant Testing of Microbubble Column Flotation.`` The objectives of this research and development effort were to duplicate the bench-scale performance of the MCF process in a full-scale unit, to verify the scale-up procedure developed in an earlier project, and to demonstrate the applicability of the MCF technology to the coal industry.

  9. The flotation of rare earths - a contribution to industrial hygiene

    International Nuclear Information System (INIS)

    Andrews, W.H.; Collins, D.N.; Hollick, C.T.

    1990-01-01

    Conventional processing of heavy mineral deposits containing radioactive rare earth minerals such as monazite and xenotime may cause industrial hygiene problems through atmospheric dust and contamination of product concentrates. An alternative procedure has been developed by Wimmera Industrial Mineral Pty. Ltd. at the Drung South deposit in Victoria. The radioactive minerals are removed from bulk heavy mineral concentrates by flotation with little loss of other economic minerals. With fine ores, recoveries of over 95% have been achieved and with coarse ores over 80%. The potential for generation of radioactive dust or product contamination in subsequent processing is correspondingly reduced. Several flotation regimes, which have proven effective are discussed. 7 refs., 7 tabs., 1 fig

  10. State of the art on ion and precipitate flotation

    International Nuclear Information System (INIS)

    Jung, In Ha; Yang, Myung Seung; Bae, Ki Kwang; Shon, Jong Sik; Cho, Young Hyun

    1997-08-01

    This report is contained research status of foam separation technique and thus theoretical backgrounds, the kinds of surfactants using for the foam separation technique, their characteristics, general structure and role, surfactant absorption mechanism at liquid/vapor/solid interfaces, effectiveness and efficiency were interpreted with well known models. Ion flotation and precipitate flotation which are applicable for the treatment of very low radioactive liquid wastes were analyzed on the effect of pH, foreign ions, initial concentration of metal ion through the recent presented papers. As the result of technical analysis of foam separation technique, foam separation technique seems to be applicable for the treatment of very low radioactive liquid wastes such as laundry and shower waste. (author). 42 refs., 2 tabs., 37 figs

  11. In-plant testing of microbubble column flotation

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, R.H.; Luttrell, G.H.; Adel, G.T.; Mankosa, M.J.

    1991-07-31

    Microbubble column flotation (MCF) was developed at the Virginia Center for Coal and Minerals Processing (VCCMP) for the selective recovery of fine particles. Bench-scale test work conducted at VCCMP, largely under the sponsorship of the U.S. Department of Energy (DOE), showed that the technology worked well for both coal and mineral applications. For the technology to be commercially successful, however, a full-scale demonstration of the MCF technology was deemed necessary. This report summarizes the results of work performed under the DOE project entitled In-plant Testing of Microbubble Column Flotation.'' The objectives of this research and development effort were to duplicate the bench-scale performance of the MCF process in a full-scale unit, to verify the scale-up procedure developed in an earlier project, and to demonstrate the applicability of the MCF technology to the coal industry.

  12. Watertightness in anti-flotation slabs: MIS-RJ case

    Directory of Open Access Journals (Sweden)

    C. Britez

    Full Text Available It is common in coastal cities as Rio de Janeiro, that buildings located close to the shoreline have their basements below water table level. In most cases, the engineering solution for these buildings is to design a massive anti-flotation slab to satisfy, principally, the issues related to structural dimensioning and calculation hypothesis. On the other hand, the execution of this solution imply in significant construction problems related to reinforced concrete watertightness and durability. This paper presents a case study about challenges and solutions devised to execute an anti-flotation, 1m thick, 1200m³ reinforced concrete slab for the new Museu de Imagem e Som (MIS - Sound and Image Museum, located at 50m from the seashore, at Copacabana in Rio de Janeiro, RJ. The results show that concrete proportions, concreting plan and pouring method adopted were decisive in obtaining a watertight structure, avoiding thus the employment of traditional waterproofing alternatives.

  13. Flotation of phosphorous-uraniferous minerals from Itataia

    International Nuclear Information System (INIS)

    Aquino, J.A. de.

    1984-01-01

    Experimental conditions were established, in laboratory and pilot scales, for the flotation of a sample of a phosphorus-uraniferous mineral from Itataia mines (CE, Brazil), basically composed of apatite and calcite. Laboratory investigations led to the optimization of the most important flotation variables and of the reagents system (tall-oil, collamil and sodium silicate) in the roughing, scavenging and cleaning steps of the process. In pilot scale, flowsheet tests were performed under the same conditions proposed for laboratory studies. The optimization of laboratory conditions led to the following yields: 29.3% of P 2 O 5 concentrates and 73.5% P 2 O 5 recovery. In the pilot scale tests, 28.4% of P 2 O 5 concentrates and 76.7% P 2 O 5 recovery yields were obtained. (Author) [pt

  14. Utilization of used motor oils as non-ionogenic collectors in the flotation process

    Science.gov (United States)

    Závada, J.; Sobková, I.; Surmová, M.; Bouchal, T.; Mudruňka, J.

    2017-10-01

    This paper deals with the possibility of the utilization of used motor oils as non-ionic collectors in the flotation separation. Flotation tests were performed on a sample of coal from Poland. The criterion was to achieve the yield of concentrate over 70% and ash content below 10%. The results of laboratory investigations have shown that the application of used motor oils as flotation agents is possible.

  15. An In-Plant Evaluation of Froth Washing on Conventional Flotation Cells for Coal

    OpenAIRE

    McKeon, Timothy Josiah

    2001-01-01

    Column flotation cells have become increasingly popular in the coal industry due to their ability to improve flotation selectivity. The improvement can be largely attributed to the use of froth washing, which minimizes the nonselective entrainment of ultrafine minerals matter into the froth product. Unfortunately, the practice of adding wash water in conventional flotation machines has been largely unsuccessful in industrial trials. In order to better understand the causes of these failure...

  16. Fine particles flotation of the Moatize coal/Mozambique

    Science.gov (United States)

    Castro, Amilton; de Brum, Irineu A. S.

    2017-11-01

    This study was done from a sample of coal mined at the Vale-Mozambique mine, located in Moatize district, Tete Province. The aim of this work is to analyze the reagent system in the flotation of coal fines belonging to the UCB layer. Among coal processing methods, flotation stands out as one of the most important for the concentration of this material, in particular in the treatment of fine particles. The total feed of the Vale-Mozambique processing plant is 8000 tph of coal, where 10% of this feed corresponds to the fine fraction that feeds the flotation circuit. The material used in this study had a particle size of 96% smaller than 0.25 mm. The reagents used in the flotation tests were Betacol and diesel oil as hydrophobizing agents and MIBC as frother. The range of Betacol concentrations in the first test phase was 200 g / t at 500 g / t, and in the second phase 200 g / t at 500 g / t of diesel oil and MIBC were kept constant at 300 g / t. The immediate analysis followed the Brazilian standards: NBR 8289, NBR 8293, NBR 8290, NBR 8299. The results showed that it is possible, from a feed with the ash content around 22.84%, to obtain products with levels below of 10% ash, with a mass recovery around 50%. The recovery of carbonaceous matter was also evaluated and presented positive results. Complementing this study, the effect of H2O recovery was evaluated and it was observed that for the concentrations of Betacol the recoveries ranged from 6 to 9%, and for diesel oil plus MIBC were 4 to 7%.

  17. Flotation separation of hafnium(IV) from aqueous solutions

    International Nuclear Information System (INIS)

    Downey, D.M.; Narick, C.N.; Cohen, T.A.

    1985-01-01

    A simple, rapid method for the separation of hafnium from aqueous solutions was investigated using sup(175+181)Hf tracer. Cationic hafnium complex ions were floated from dilute acid solutions with sodium lauryl sulfate (SLS) and anionic hafnium complexes were floated from basic and oxalic acid solutions with hexadecyltrimethyl ammonium bromide (HTMAB). The conditions necessary for quantitative recovery of the metal and mechanisms of flotation are described. (author)

  18. Impact of flocculation on flotation tailing's hydro-cycloning properties

    Directory of Open Access Journals (Sweden)

    Knežević Dinko N.

    2014-01-01

    Full Text Available Research results of hydro-cycloning of flocculated and non-flocculated flotation tailing from the lead and zinc open pit mine 'Suplja stijena', Sula - Montenegro have been shown in this paper. Reason for this research was finding conditions in order to separate fraction that is suitable for embankment erection. Flotation tailings has been tested in the very state that it goes out from the flotation process and tailings which is flocculated by anionic flocculant. The object was to determine the impact of flocculation on properties of hydro-cycloning products and disposal process. In hydro-cycloning process greater underflow mass is being separated with non-flocculated tailing. Values of geomechanical parameters are significantly different, especially hydro-cyclone's underflow. All geomechanical parameters of hydro-cyclone's underflow are suitable for erecting embankment which shall be made from non-flocculated tailing. Underflow drainage of non-flocculated tailing is faster while overflow drainage is slower and problematic with both tailings.

  19. Flotation and flocculation chemistry of coal and oxidized coals

    Energy Technology Data Exchange (ETDEWEB)

    Somasundaran, P.

    1990-01-01

    The objective of this research project is to understand the fundamentals involved in the flotation and flocculation of coal and oxidized coals and elucidate mechanisms by which surface interactions between coal and various reagents enhance coal beneficiation. An understanding of the nature of the heterogeneity of coal surfaces arising from the intrinsic distribution of chemical moieties is fundamental to the elucidation of mechanism of coal surface modification and its role in interfacial processes such as flotation, flocculation and agglomeration. A new approach for determining the distribution in surface properties of coal particles was developed in this study and various techniques capable of providing such information were identified. Distributions in surface energy, contact angle and wettability were obtained using novel techniques such as centrifugal immersion and film flotation. Changes in these distributions upon oxidation and surface modifications were monitored and discussed. An approach to the modelling of coal surface site distributions based on thermodynamic information obtained from gas adsorption and immersion calorimetry is proposed. Polyacrylamide and dodecane was used to alter the coal surface. Methanol adsorption was also studied. 62 figs.

  20. Treatment of wastewater containing dissolved metals by extraction-flotation

    International Nuclear Information System (INIS)

    Puget, Flavia Pereira

    2002-02-01

    In this work an alternative process for treating a wastewater containing dissolved metals (uranium and zirconium) is considered. In order to develop this work, a continuous separation unit, characterized by the association of solvent extraction and liquid-liquid flotation is used. Alamina 336 (a mixture of tri-octyl and tri-decyl amines) is used as extractant in the the extraction process, carried out inward the ejector. The splitting of the amine-water emulsion formed is carried out in a continuously operated flotation column (of approximately 2.5 L volume). The solvent extraction results showed that it is possible to reach an efficiency of about 95% for the uranium and zirconium extraction, for a metal in the feed concentration of 10 ppm and for a Q fa /Q fo ratio around 200. An efficiency of about 80% is reached in the flotation column when the liquid flowrate is equal 0.05 Lmin -1 and the air flowrate is equal 3.3 Lmin -1 . (author)

  1. Estimated water requirements for the conventional flotation of copper ores

    Science.gov (United States)

    Bleiwas, Donald I.

    2012-01-01

    This report provides a perspective on the amount of water used by a conventional copper flotation plant. Water is required for many activities at a mine-mill site, including ore production and beneficiation, dust and fire suppression, drinking and sanitation, and minesite reclamation. The water required to operate a flotation plant may outweigh all of the other uses of water at a mine site, [however,] and the need to maintain a water balance is critical for the plant to operate efficiently. Process water may be irretrievably lost or not immediately available for reuse in the beneficiation plant because it has been used in the production of backfill slurry from tailings to provide underground mine support; because it has been entrapped in the tailings stored in the TSF, evaporated from the TSF, or leaked from pipes and (or) the TSF; and because it has been retained as moisture in the concentrate. Water retained in the interstices of the tailings and the evaporation of water from the surface of the TSF are the two most significant contributors to water loss at a conventional flotation circuit facility.

  2. Coal Recycling from Tailings using Flotation with 2-Level Experimental Design Techniques

    Directory of Open Access Journals (Sweden)

    Sajjad Jannesar Malakooti

    2012-12-01

    Full Text Available In this study, the possibility of producing coal with less than 11% ash from tailings of flotation process was investigated. The effect of six flotation parameters: collector type, collector consumption, frother type, frother consumption, pulp density and mixing rate were studied on a sample from a tailing dam. A software based experimental design approach (DX7 was applied to determine and model effective parameters as well as flotation optimization through fractional factorial. It was shown that collector type and flotation machine mixing rate were the most effective parameters on ash content of concentrate. The results indicated that the production of a desired ash content concentrate, i.e.

  3. Optimizing the grain size distribution for talc-magnesite ore flotation

    Directory of Open Access Journals (Sweden)

    Škvarla Jiøí

    2001-06-01

    Full Text Available Flotation is the only separation method with an universal utilization. Along with the separation of particulate valuable or hazardous components from primary and seconadry mineral raw materials, it is of usage in biotechnologies and water cleaning. The success of the flotation separation crucially depends on the particle size distribution or composition of the ore charge entering the process. The paper deals with the problem of flotation treatment of talc-magnesite ore. The main components of the ore, i.e. talc and magnesite are appreciably different in their grindability and floatability. For such a type of raw material, grinding of the charge plays a very important role in the process. The (unwanted influence of ultrafine particles on the course of the flotation process is well known. On the other hand, in order to liberate and subsequently to selectively separate both the components, a maximum particle size has to be respected.An influence of artificial samples of selected particle size fractions on the flotation efficiency has been studied experimentally by the quantitative evaluation of flotation products. The flotation experiments on the samples provided an information not obtainable from traditional flotation tests. An adverse effect of the size fraction 0 – 0.04 mm was revealed, decreasing the flotation selectivity appreciably. These results are of theoretical and practical importance.

  4. Flotation: A promising microalgae harvesting and dewatering technology for biofuels production.

    Science.gov (United States)

    Ndikubwimana, Theoneste; Chang, Jingyu; Xiao, Zongyuan; Shao, Wenyao; Zeng, Xianhai; Ng, I-Son; Lu, Yinghua

    2016-03-01

    Microalgal biomass as renewable energy source is believed to be of great potential for reliable and sustainable biofuels production. However, microalgal biomass production is pinned by harvesting and dewatering stage thus hindering the developing and growing microalgae biotechnology industries. Flotation technology applied in mineral industry could be potentially applied in microalgae harvesting and dewatering, however substantial knowledge on different flotation units is essential. This paper presents an overview on different flotation units as promising cost-effective technologies for microalgae harvesting thus bestowing for further research in development and commercialization of microalgae based biofuels. Dispersed air flotation was found to be less energy consuming. Moreover, Jameson cell flotation and dispersed ozone flotation are believed to be energy efficient microalgae flotation approaches. Microalgae harvesting and dewatering by flotation is still at embryonic stage, therefore extended studies with the focus on life cycle assessment, sustainability of the flotation unit, optimization of the operating parameters using different algal species is imperative. Though there are a number of challenges in microalgae harvesting and dewatering, with well designed and developed cultivation, harvesting/dewatering, extraction and conversion technologies, progressively, microalgae technology will be of great potential for biological carbon sequestration, biofuels and biochemicals production. Copyright © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Ambient Temperature Flotation of Sedimentary Phosphate Ore Using Cottonseed Oil as a Collector

    Directory of Open Access Journals (Sweden)

    Yaoyang Ruan

    2017-04-01

    Full Text Available The mid-low grade sedimentary phosphate ore, abundant in silicate and carbonate gangue minerals, exhibits a poor processability. It is conventionally enriched using high temperature flotation to remove silicate gangues with fatty acid as a collector. Cottonseed oil has been proved to be an efficient collector for achieving ambient temperature flotation of the sedimentary phosphate ore used in this study. Flotation kinetics was investigated to ascertain the excellent collecting performance of cottonseed oil, as compared with oleic acid, and the phosphate flotation fitted well with the first-order flotation model. Based on the analysis of flotation reagent effect on the direct flotation process using the response surface methodology (RSM, a closed circuit of direct-reverse flotation for stepwise removing silicate and carbonate gangues from the sedimentary phosphate ore was established. Consequently, a required high quality of phosphate concentrate containing 30.16% P2O5 was obtained, with a recovery of 90.90%. Scanning electron microscopy (SEM and X-ray diffraction analysis (XRD of the flotation products confirmed that the majority of silicate and carbonate gangues were effectively removed from the concentrate products.

  6. Local evolution of seed flotation in Arabidopsis.

    OpenAIRE

    Susana Saez-Aguayo; Corinne Rondeau-Mouro; Audrey Macquet; Ilkka Kronholm; Marie-Christine Ralet; Adeline Berger; Christine Sallé; Damien Poulain; Fabienne Granier; Lucy Botran; Olivier Loudet; Juliette de Meaux; Annie Marion-Poll; Helen M North

    2014-01-01

    Arabidopsis seeds rapidly release hydrophilic polysaccharides from the seed coat on imbibition. These form a heavy mucilage layer around the seed that makes it sink in water. Fourteen natural Arabidopsis variants from central Asia and Scandinavia were identified with seeds that have modified mucilage release and float. Four of these have a novel mucilage phenotype with almost none of the released mucilage adhering to the seed and the absence of cellulose microfibrils. Mucilage release was mod...

  7. Local Evolution of Seed Flotation in Arabidopsis

    OpenAIRE

    Saez Aguayo, S.; Rondeau Mouro, C.; Macquet, A.; Kronholm, I.; Ralet, M.C.; Berger, A.; Sallé, C.; Poulain, D.; Granier, F.; Botran, L.; Loudet, O.; De Meaux, J.; Marion-Poll, A.; North, H.; Botran, L.

    2014-01-01

    Arabidopsis seeds rapidly release hydrophilic polysaccharides from the seed coat on imbibition. These form a heavy mucilage layer around the seed that makes it sink in water. Fourteen natural Arabidopsis variants from central Asia and Scandinavia were identified with seeds that have modified mucilage release and float. Four of these have a novel mucilage phenotype with almost none of the released mucilage adhering to the seed and the absence of cellulose microfibrils. Mucilage release was mod...

  8. Using flotation in ethanol to separate filled and empty seeds of Pinus ...

    African Journals Online (AJOL)

    In this study, the separation of filled and empty seeds of Crimean pine [Pinus nigra Arn. ssp. pallasiana (Lamb.) Holmboe] by flotation in ethanol and the effect of this treatment on seed germination were investigated. Flotation tests in 96% ethanol by the density method and then germination tests were made on the seeds ...

  9. Effect of mechanical and chemical clay removals by hydrocyclone and dispersants on coal flotation

    Energy Technology Data Exchange (ETDEWEB)

    Oats, W.J.; Ozdemir, O.; Nguyen, A.V. [University of Queensland, Brisbane, Qld. (Australia). School of Chemical Engineering

    2010-04-15

    Fine minerals, mostly clays, are known to have a detrimental effect on coal flotation. This paper focuses on the effect of mechanical and chemical removals of fine minerals by hydrocyclone and dispersants on coal flotation. The experimental results showed that the flotation recovery slightly increased from medium acidic to medium alkaline ranges. The flotation experiments carried out with dispersants at different dosages showed that the dispersants did not enhance the flotation recovery significantly. However, the removal of the fine fraction from the feed using a hydrocyclone significantly increased the flotation recovery. The bubble-particle attachment tests also indicated that the attachment time between an air bubble and the coal particles increased in the presence of clay particles. These attachment time results clearly showed that the clay particles adversely affected the flotation of coal particles by covering the coal surfaces which reduced the efficiency of bubble-coal attachment. An analysis based on the colloid stability theory showed that the clay coating was governed by the van der Waals attraction and that the double-layer interaction played a secondary role. It was also concluded that the best way to increase the flotation recovery in the presence of clays was to remove these fine minerals by mechanical means such as hydrocylones.

  10. Evaluation of Gas Phase Dispersion in Flotation under Predetermined Hydrodynamic Conditions

    Science.gov (United States)

    Młynarczykowska, Anna; Oleksik, Konrad; Tupek-Murowany, Klaudia

    2018-03-01

    Results of various investigations shows the relationship between the flotation parameters and gas distribution in a flotation cell. The size of gas bubbles is a random variable with a specific distribution. The analysis of this distribution is useful to make mathematical description of the flotation process. The flotation process depends on many variable factors. These are mainly occurrences like collision of single particle with gas bubble, adhesion of particle to the surface of bubble and detachment process. These factors are characterized by randomness. Because of that it is only possible to talk about the probability of occurence of one of these events which directly affects the speed of the process, thus a constant speed of flotation process. Probability of the bubble-particle collision in the flotation chamber with mechanical pulp agitation depends on the surface tension of the solution, air consumption, degree of pul aeration, energy dissipation and average feed particle size. Appropriate identification and description of the parameters of the dispersion of gas bubbles helps to complete the analysis of the flotation process in a specific physicochemical conditions and hydrodynamic for any raw material. The article presents the results of measurements and analysis of the gas phase dispersion by the size distribution of air bubbles in a flotation chamber under fixed hydrodynamic conditions. The tests were carried out in the Laboratory of Instrumental Methods in Department of Environmental Engineering and Mineral Processing, Faculty of Mining and Geoengineerin, AGH Univeristy of Science and Technology in Krakow.

  11. Neural network modelling and prediction of the flotation deinking behaviour of industrial paper recycling processes

    CSIR Research Space (South Africa)

    Pauck, WJ

    2014-01-01

    Full Text Available The removal of ink from recovered papers by flotation deinking is considered to be the “heart” of the paper recycling process. Attempts to model the deinking flotation process from first principles has resulted in complex and not readily usable...

  12. Flotation performances and surface properties of chalcopyrite with xanthate collector added before and after grinding

    Science.gov (United States)

    Peng, Huiqing; Wu, Di; Abdelmonem, Mohamed

    In this study, effects of the collector added before grinding and after grinding on the subsequent flotation and mineral surface properties were investigated. The pH was controlled at 10 during the grinding and flotation processes opened to the atmosphere. With enough amounts of sodium butyl xanthate addition, adding the collector before grinding recovered more chalcopyrite than adding it after grinding in single mineral flotation. The Eh of each ground pulp before and after conditioning were measured and it was found that adding collector before grinding obtained higher and relatively suitable pulp potential for chalcopyrite flotation. Particle size analyses of the flotation products indicate that the different flotation recoveries occurred due to the different flotation losses in fine particles (<20 μm). XPS analyses focused on the fine particles of flotation feedings and found that more carbon and oxygen, and less iron were remained on mineral surfaces when the collector was added before grinding, due to the higher collector adsorption capacity, larger free oxygen adsorbance and less iron oxide/hydroxide species.

  13. Froth conductivity for in situ monitoring of fiber (solid) and wet rejects in flotation deinking

    Science.gov (United States)

    J. Y. Zhu; M. Fleischmann; R. Gleisner

    2006-01-01

    Reduced fiber rejection in flotation deinking is very important to reduce the cost of secondary fibers in paper recycling and to conserve natural resources. Online monitoring of fiber rejection is a prerequisite to achieving process control for the reduction of fiber rejection in flotation deinking. It also can improve understanding of the effects of various operating...

  14. Using flotation in ethanol to separate filled and empty seeds of Pinus ...

    African Journals Online (AJOL)

    USER

    2010-06-21

    Jun 21, 2010 ... and empty seeds by the flotation method. It is quite important not to damage the seed embryo and con- sequently seed germination ability during or after the flotation treatment by these liquids that have different densities. On the other hand, when Crimean pine seeds are left in water, the seeds generally ...

  15. Evaluation of Gas Phase Dispersion in Flotation under Predetermined Hydrodynamic Conditions

    Directory of Open Access Journals (Sweden)

    Młynarczykowska Anna

    2018-01-01

    Full Text Available Results of various investigations shows the relationship between the flotation parameters and gas distribution in a flotation cell. The size of gas bubbles is a random variable with a specific distribution. The analysis of this distribution is useful to make mathematical description of the flotation process. The flotation process depends on many variable factors. These are mainly occurrences like collision of single particle with gas bubble, adhesion of particle to the surface of bubble and detachment process. These factors are characterized by randomness. Because of that it is only possible to talk about the probability of occurence of one of these events which directly affects the speed of the process, thus a constant speed of flotation process. Probability of the bubble-particle collision in the flotation chamber with mechanical pulp agitation depends on the surface tension of the solution, air consumption, degree of pul aeration, energy dissipation and average feed particle size. Appropriate identification and description of the parameters of the dispersion of gas bubbles helps to complete the analysis of the flotation process in a specific physicochemical conditions and hydrodynamic for any raw material. The article presents the results of measurements and analysis of the gas phase dispersion by the size distribution of air bubbles in a flotation chamber under fixed hydrodynamic conditions. The tests were carried out in the Laboratory of Instrumental Methods in Department of Environmental Engineering and Mineral Processing, Faculty of Mining and Geoengineerin, AGH Univeristy of Science and Technology in Krakow.

  16. Local evolution of seed flotation in Arabidopsis.

    Directory of Open Access Journals (Sweden)

    Susana Saez-Aguayo

    2014-03-01

    Full Text Available Arabidopsis seeds rapidly release hydrophilic polysaccharides from the seed coat on imbibition. These form a heavy mucilage layer around the seed that makes it sink in water. Fourteen natural Arabidopsis variants from central Asia and Scandinavia were identified with seeds that have modified mucilage release and float. Four of these have a novel mucilage phenotype with almost none of the released mucilage adhering to the seed and the absence of cellulose microfibrils. Mucilage release was modified in the variants by ten independent causal mutations in four different loci. Seven distinct mutations affected one locus, coding the MUM2 β-D-galactosidase, and represent a striking example of allelic heterogeneity. The modification of mucilage release has thus evolved a number of times independently in two restricted geographical zones. All the natural mutants identified still accumulated mucilage polysaccharides in seed coat epidermal cells. Using nuclear magnetic resonance (NMR relaxometry their production and retention was shown to reduce water mobility into internal seed tissues during imbibition, which would help to maintain seed buoyancy. Surprisingly, despite released mucilage being an excellent hydrogel it did not increase the rate of water uptake by internal seed tissues and is more likely to play a role in retaining water around the seed.

  17. Local evolution of seed flotation in Arabidopsis.

    Science.gov (United States)

    Saez-Aguayo, Susana; Rondeau-Mouro, Corinne; Macquet, Audrey; Kronholm, Ilkka; Ralet, Marie-Christine; Berger, Adeline; Sallé, Christine; Poulain, Damien; Granier, Fabienne; Botran, Lucy; Loudet, Olivier; de Meaux, Juliette; Marion-Poll, Annie; North, Helen M

    2014-03-01

    Arabidopsis seeds rapidly release hydrophilic polysaccharides from the seed coat on imbibition. These form a heavy mucilage layer around the seed that makes it sink in water. Fourteen natural Arabidopsis variants from central Asia and Scandinavia were identified with seeds that have modified mucilage release and float. Four of these have a novel mucilage phenotype with almost none of the released mucilage adhering to the seed and the absence of cellulose microfibrils. Mucilage release was modified in the variants by ten independent causal mutations in four different loci. Seven distinct mutations affected one locus, coding the MUM2 β-D-galactosidase, and represent a striking example of allelic heterogeneity. The modification of mucilage release has thus evolved a number of times independently in two restricted geographical zones. All the natural mutants identified still accumulated mucilage polysaccharides in seed coat epidermal cells. Using nuclear magnetic resonance (NMR) relaxometry their production and retention was shown to reduce water mobility into internal seed tissues during imbibition, which would help to maintain seed buoyancy. Surprisingly, despite released mucilage being an excellent hydrogel it did not increase the rate of water uptake by internal seed tissues and is more likely to play a role in retaining water around the seed.

  18. Influence of liberation of sulphide minerals on flotation of sedimentary copper ore

    Directory of Open Access Journals (Sweden)

    Bakalarz Alicja

    2017-01-01

    Full Text Available Ore liberation is one of the most important parameter in mineral processing, especially in flotation. To separate the valuable components from gangue minerals, it is necessary to liberate one from others. It is achieve primarily through crushing and grinding. These stages are one of the most expensive of mineral production. It is important to determine the adequate mineral liberation which would result in huge savings in the overall cost of flotation plant. The aim of the paper was the analysis of the influence of milling time on the laboratory flotation of the copper ore from stratiform Polish deposit. Three different milling time of copper ore in laboratory ball mill was applied. The flotation results were presented as the recovery-recovery and grade-recovery upgrading curves. The liberation of sulphides and the particle size of sulphides in flotation product were analysed and compared.

  19. Dissolved air flotation of polishing wastewater from semiconductor manufacturer.

    Science.gov (United States)

    Liu, J C; Lien, C Y

    2006-01-01

    The feasibility of the dissolved air flotation (DAF) process in treating chemical mechanical polishing (CMP) wastewater was evaluated in this study. Wastewater from a local semiconductor manufacturer was sampled and characterised. Nano-sized silica (77.6 nm) with turbidity of 130 +/- 3 NTU was found in the slightly alkaline wastewater with traces of other pollutants. Experimental results indicated removal efficiency of particles, measured as suspended particle or turbidity, increased with increasing concentration of cationic collector cetyltrimethyl ammonium bromide (CTAB). When CTAB concentration was 30 mg/L, pH of 6.5 +/- 0.1 and recycle ratio of 30%, very effective removal of particles (> 98%) was observed in saturation pressure range of 4 to 6 kg/cm2, and the reaction proceeded faster under higher pressure. Similarly, the reaction was faster under the higher recycle ratio, while final removal efficiency improved slightly as the recycle ratio increased from 20 to 40%. An insignificant effect of pH on treatment efficiency was found as pH varied from 4.5 to 8.5. The presence of activator, Al3+ and Fe3+, enhanced the system performance. It is proposed that CTAB adsorbs on silica particles in polishing wastewater through electrostatic interaction and makes particles more hydrophobic. The increase in hydrophobicity results in more effective bubble-particle collisions. In addition, flocculation of silica particles through bridging effect of collector was found; it is believed that flocculation of particles also contributed to flotation. Better attachment between gas bubble and solid, higher buoyancy and higher air to solid ratio all lead to effective flotation.

  20. Improving the performance of conventional and column froth flotation cells

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, B.J. [CQ Inc., Homer City, PA (United States)

    1995-11-01

    Many existing mining operations hover on the brink of producing competitively priced fuel with marginally acceptable sulfur levels. To remain competitive, these operations need to improve the yield of their coal processing facilities, lower the sulfur content of their clean coal, or lower the ash content of their clean coal. Fine coal cleaning processes offer the best opportunity for coal producers to increase their yield of high quality product. Over 200 coal processing plants in the U.S. already employ some type of conventional or column flotation device to clean fines. an increase in efficiency in these existing circuits could be the margin required to make these coal producers competitive.

  1. The kinetics of fossil resin extraction from a flotation concentrate

    Energy Technology Data Exchange (ETDEWEB)

    Li, L.; Yu, Q.; Miller, J.D. [Univ. of Utah, Salt Lake City, UT (United States)

    1995-11-01

    The kinetics of fossil resin extraction from a flotation concentrate by heptane were investigated as a function of process variables using monosize particles. Experimental results provide for a better understanding of the refining process and the basis for subsequent design and construction of a continuous resin refining circuit. Based on the effect of process variables (particle size, stirring speed, and temperature) the resin extraction rate appears to be controlled by surface solvation phenomena. The initial extraction rate was found to be inversely proportional to the initial particle size and a kinetic model is being developed to describe the experimental results.

  2. Cadmium elemination from phosphoric acid by ionic flotation

    International Nuclear Information System (INIS)

    Brikci-Nigassa, Mounir; Hamouche, Hafida

    1995-11-01

    The ion flotation process for the recovery of cadmium from wet phosphoric acid (30%P2O5) has been studied. This technique combines a chemical recation between the collector and the cadmium to form a precipitate (sublate) which is carried to the surface of the solution by air bubbles. the resulting foam containing the cadmium may then separated from solution. The influence of parameters such as collector and cadmium concentration as well as iron content have been investigated for the case a synthetic acid (30% P2O5). The result have been applied to the industrial phosphoric acid produced from Djebel Onk's phosphates (Algeria)

  3. KOMBINASI ULTRAFILTRASI DAN DISSOLVED AIR FLOTATION UNTUK PEMEKATAN MIKROALGA

    Directory of Open Access Journals (Sweden)

    I Nyoman Widiasa

    2014-05-01

    Full Text Available Abstrak Mikroalga merupakan mikroorganisme fotosintetik prokariotik atau eukariotik yang dapat tumbuh dengan cepat. Pemanfaatan mikroalga tidak hanya berorientasi sebagai pakan alami untuk akuakultur, tetapi terus berkembang untuk bahan baku produksi pakan ternak, pigmen warna, bahan farmasi (β-carotene, antibiotik, asam lemak omega-3, bahan kosmetik, pupuk organik, dan biofuel (biodiesel, bioetanol, biogas, dan biohidrogen. Studi ini bertujuan untuk menginvestigasi kombinasi ultrafiltrasi (UF – dissolved air flotation (DAF untuk pemekatan mikroalga skala laboratorium. Hasil penelitian menunjukkan bahwa penurunan fluks membran UF secara tajam sebagai akibat dari deposisi sel mikroalga terjadi pada 20 menit pertama proses filtrasi. Backwash pada interval 20 menit selama 10 detik dengan tekanan 1 bar memberikan pengendalian fouling yang efektif dalam nilai kestabilan fluks yang layak. Membran UF yang digunakan dapat memberikan selektivitas pemisahan biomassa mikroalga ~ 100%. Kualitas permeat sangat stabil, yaitu kekeruhan < 0,5 NTU, kandungan organik < 10 mg/L, dan warna < 10 PCU. Lebih lanjut, pemekatan retentat membran dengan DAF pada tekanan saturasi 6 bar dapat menghasilkan pasta mikroalga dengan konsentrasi 20 g/L. Koagulan PAC perlu ditambahkan kedalam umpan DAF dengan dosis 1,3–1,6 mg PAC/mg padatan tersuspensi.   Kata Kunci: ultrafiltrasi; dissolved air flotation; pemanenan mikroalga; pemekatan mikroalga   Abstract COMBINATION OF Ultrafiltration and Dissolved Air Flotation for Microalgae CONCENTRATION. Microalgae is a prokaryotic photosynthetic microorganism or eukaryotic microorganism  that proliferate rapidly. Cultivation of the microalgae is not only oriented  as natural food for aquacultures, but also developed  for animal food, color pigment, pharmaceutical raw material (β-carotene, antibiotic, fatty acid omega-3, cosmetic raw material, organic fertilizer, and biofuels (biodiesel, bioethanol, biogas, and biohydrogen. This

  4. Coal surface control for advanced fine coal flotation

    Energy Technology Data Exchange (ETDEWEB)

    Fuerstenau, D.W.; Hanson, J.S.; Diao, J.; Harris, G.H.; De, A.; Sotillo, F. (California Univ., Berkeley, CA (United States)); Somasundaran, P.; Harris, C.C.; Vasudevan, T.; Liu, D.; Li, C. (Columbia Univ., New York, NY (United States)); Hu, W.; Zou, Y.; Chen, W. (Utah Univ., Salt Lake City, UT (United States)); Choudhry, V.; Shea, S.; Ghosh, A.; Sehgal, R. (Praxis Engineers, Inc., Milpitas, CA (United States))

    1992-03-01

    The initial goal of the research project was to develop methods of coal surface control in advanced froth flotation to achieve 90% pyritic sulfur rejection, while operating at Btu recoveries above 90% based on run-of-mine quality coal. Moreover, the technology is to concomitantly reduce the ash content significantly (to six percent or less) to provide a high-quality fuel to the boiler (ash removal also increases Btu content, which in turn decreases a coal's emission potential in terms of lbs SO{sub 2}/million Btu). (VC)

  5. Dolomite flotation of high magnesium phosphate ores using fatty acid soap collectors

    Science.gov (United States)

    Gu, Zhengxing

    The separation of dolomite from apatite has been recognized as one of the most difficult subjects in mineral processing due to the similarities in their physiochemical properties. In this study, selective surfactants were used with a fatty acid soap collector to improve the flotation performance of separating dolomite from high magnesium phosphate ores. Three surfactants, diethyl phthalate (DP), Tween-80 (TW) and derivative of sulfonate salt (DSS1) were used. Hallimond cell flotation was conducted using pure dolomite sample to determine the effects of various factors including dosages, particle size, Ca2+ ions and slimes on the dolomite flotation recovery. The results showed that the surfactants can significantly improve dolomite flotation performance by increasing collecting ability and tolerating the effect of calcium ions and slime contents. The stirrer-tank cell batch flotation tests were carried out using two natural high magnesium phosphate ore samples containing 3.3% and 1.5% MgO. The test results showed that the surfactant DP could improve dolomite flotation at low dosages, and DSS1 could enhance the separation of dolomite from phosphate by improving both collecting ability and flotation selectivity. When 10% of DSS1 was used with the fatty acid soap as collector, at least 10% more dolomite can be removed with less P2O5 loss. The effectiveness of the surfactant DSS1 in enhancing dolomite flotation was further demonstrated in modified packed column flotation with natural dolomitic phosphate ore sample. The addition of the surfactant DSS1 into fatty acid soap collector could improve its frothability and froth stability, and reduce the bubble size. It has been found that the dolomite flotation performance has a close relationship with the frothability and froth stability of the collector.

  6. THE MECHANISM OF FLOTATION ISOLATION FINE-EMULSIFIED FATTY ACIDS

    Directory of Open Access Journals (Sweden)

    V. F. Sazonova

    2015-02-01

    Full Text Available It is positioned, that the flotation mechanism fine-emulsified fatty acids is defined by a sign and value of an electrokinetic potential of fatty acids drops and air bubbles, and also a parity of attractive forces and pushing away between drops and air bubbles which, in turn, are functions pH medium. It is shown, that in the subacidic medium (pH 6 extraction degree makes 97 %, flotation process is described by the kinetic equation of the first order, and interaction of drops and air bubbles is carried out in absence of energy barrier of pushing away between them. At increase in acidity of medium (pH 2 extraction degree decreases to 40 %, order of the kinetic equation changes from the first on the second, and fastening of drops on a surface of air bubbles occurs as a result of distant interaction (in a distant potential minimum on the graph of potential energy of interaction of drops and air bubbles from distances between them.

  7. Determination of molybdenum in flotation concentrates by atomic absorption spectrophotometry

    International Nuclear Information System (INIS)

    Ise, Kazuo

    1978-01-01

    Molybdenum was determined by atomic absorption spectrophotometry in 0.05 N ammoniacal solution after the decomposition of the concentrate with aqua regia. Negros ore from Philippines was used as a flotation feed, which contained chalcopyrites and calcium-magnesium minerals. Among the metals tested copper, iron and the alkaline earths interfered. Less than 50 ppm of copper yielded lower results for molybdenum. Higher results came out with more than 50 ppm of copper. In the presence of iron and citric acid (0.4 g/100 ml) which is a suppressor for hydroxide formation, a lower estimation resulted for molybdenum. Calcium interfered, lower results by 2 and >10% being obtained with respective 2.5 and 20 ppm of calcium. More than 20 ppm of magnesium behaved similarly. Sodium sulfate (0.5 g/100 ml) served as the suppressor for copper, iron and citric acid; 100 ppm each of copper and iron did not interfere in this way. Interferences due to calcium and magnesium (less than 60 ppm) was able to be masked by the addition of sodium silicate (200 ppm as silica). The analysis of flotation products and synthetic samples consisting of molybdenite, chalcopyrite, calcium chloride and magnesium sulfate revealed that the atomic absorption method can be applied to the analysis of the concentrates for molybdenum with an error of about 2%. (auth.)

  8. Recovery of uranium low grade ores by froth flotation: study of the texture and synergetic effects of flotation reagents

    International Nuclear Information System (INIS)

    Duverger, Agathe

    2013-01-01

    Due to the energy growing demand, uranium low grade ores may be those exploited in the future. Uranium ores conventional treatment does not often use mineral processing such as concentration methods for reducing leaching reagent consumption. The aim of this work is to develop an upgrading process to improve the operating process (alkaline heap leaching) taking into account the mineralogical and textural variability of the ore. The Trekkopje deposit is composed of calcrete and a gypscrete. The uranium bearing mineral is carnotite (K 2 (UO 2 ) 2 [VO 4 ] 2 .3H 2 O). The gangue minerals are composed by silicates, such as quartz, feldspars, micas and Ca-minerals, calcite and gypsum (XRD and ICP-MS analysis). A SEM image processing was used to study the textural properties and the exposed free surface of mineral inclusions in clay clusters. In calcrete milled to -200 μm, 50 % of all carnotite is associated with clay clusters, which are composed by 98 % of palygorskite, 2 % of illite, montmorillonite, and interbedded clays (XRD and microprobe analysis). The carnotite grain size is 95 % less than 70 μm. Calcite is the main inclusion in clay clusters. Indeed, the calcite inclusions average rate in the clay clusters is 12 % and 5 % for carnotite inclusion. And the free exposed surface percentage of these minerals in clay clusters is 3 % and 6 %, thus indicating that the inclusions should not affect the behavior of mixed clay particles. However, ore flotation essays did not verify this hypothesis. Three minerals separation have been proposed based on the mineral ability to consume leaching reagents: separating Ca-minerals from silicates, palygorskite from gangue minerals and carnotite from gangue minerals. A study of silicates and Ca-minerals electrokinetic properties (electrophoresis) was carried out to select the collectors and the optimum pH range for selective flotation. Basic pH near neutral was proved to be optimal for the separation of gangue minerals with cationic

  9. Comparison of common fecal flotation techniques for the recovery of parasite eggs and oocysts.

    Science.gov (United States)

    Dryden, M W; Payne, P A; Ridley, R; Smith, V

    2005-01-01

    A variety of procedures are available to detect parasite eggs or oocysts in feces. This study compared the efficacy of simple flotation, a commercial assay, and various centrifugation techniques and three common flotation solutions. Results indicate that centrifugation consistently recovered more eggs than other methods. Proper technique is critical, including ensuring that the specific gravity of the flotation solution is correct and allowing the sample to stand for a sufficient amount of time before examining the coverslip. Because of the zoonotic health risks of many companion animal parasites, veterinarian and their staff should better utilize fecal examinations in their routine diagnostic plan.

  10. The effect of water chemistry and fibre-size distribution on dissolved air flotation efficiency

    OpenAIRE

    Sjölander, Anna

    2009-01-01

    The purpose of this diploma work was to investigate the problem of insufficient fibre recovery in the dissolved air flotation-cell at the new thermomechanical pulping-line at Braviken Paper Mill. An investigation of the effect of process parameters on the removal efficiency in the micro-flotation process was undertaken. The experiments were carried out for two setups at the Noss pilot plant with a small-scale flotation unit. Factorial design helped plan the experiments and four factors were c...

  11. Estimation of metallurgical parameters of flotation process from froth visual features

    Directory of Open Access Journals (Sweden)

    Mohammad Massinaei

    2015-06-01

    Full Text Available The estimation of metallurgical parameters of flotation process from froth visual features is the ultimate goal of a machine vision based control system. In this study, a batch flotation system was operated under different process conditions and metallurgical parameters and froth image data were determined simultaneously. Algorithms have been developed for measuring textural and physical froth features from the captured images. The correlation between the froth features and metallurgical parameters was successfully modeled, using artificial neural networks. It has been shown that the performance parameters of flotation process can be accurately estimated from the extracted image features, which is of great importance for developing automatic control systems.

  12. An Investigation of Variables in a Fecal Flotation Technique

    Science.gov (United States)

    O'Grady, M. R.; Slocombe, J. O. D.

    1980-01-01

    Several variables in a standard vial fecal gravitational flotation technique were investigated. These were the specific gravity of the sodium nitrate flotation solution, duration of flotation and mesh sizes of strainers. The number of eggs which floated and adhered to a coverslip were counted and estimates of the number of eggs remaining in the strained fecal suspension and in the feces trapped on the strainer were made. Eggs from hookworms, Trichuris vulpis and Toxocara canis in feces from dogs, Nematodirus spp. from sheep and Parascaris equorum from horses floated equally well in solutions with specific gravities (SpGr) ranging from 1.22-1.38. Taenia spp. from dogs had a slightly narrower range (SpGr 1.27-1.38) for best recovery. Eggs from Haemonchus contortus from sheep appeared to float best between SpGr 1.22- 1.32. Strongyles from one horse floated best with SpGr 1.27-1.32 and from another with SpGr 1.11-1.38. Coccidial oocysts from sheep floated best in a narrow range of SpGr from 1.22-1.27. However, as the SpGr of the solution was increased the recognition of eggs under the coverslip was increasingly difficult and especially so at SpGr 1.38 with sheep feces. This was due to the increasing amount of debris and the more rapid formation of crystals with evaporation with solutions of higher SpGr. It appeared, therefore, that solutions with SpGr of 1.22-1.35 would be best for routine laboratory use. At specific gravity 1.27, there appeared to be no difference in the number of eggs recovered for a four, eight and 12 min flotation period. Only 3-7% of the eggs in 4 g of feces were counted under the coverslip. This poor efficacy resulted first because approximately 50% of the eggs were trapped in the feces and retained on the strainer. Secondly, only one half of the strained fecal suspension, containing approximately 25% of the eggs, was placed in the vial for examination. Thirdly, of those eggs in the vial only 16-29% were counted under the coverslip. When the

  13. Comparative evaluation of a modified zinc sulfate flotation technique.

    Science.gov (United States)

    Bartlett, M S; Harper, K; Smith, N; Verbanac, P; Smith, J W

    1978-01-01

    A modified zinc sulfate flotation technique using Formalinized fecal specimens (F-ZnSO4) was compared to the Formalin-ether (FE) concentration method for the laboratory diagnosis of intestinal parasites. Many laboratories have difficulty storing, using, and disposing of either and need a procedure for concentrating fecal specimens which does not require ether. Comparative data were obtained for the recovery of protozoan cysts and helminth eggs and larvae from feces preserved in Formalin less than and longer than 1 month. Whereas the FE method was found generally to be more efficient, F-ZnSO4 was apparently more effective for the recovery of some species of parasites. F-ZnSO4 was not satisfactory for recovery of schistosome eggs. We conclude that, except for schistosomes, F-ZnSO4 compares favorably to the FE method for detecting infections of clinical significance. PMID:566767

  14. Coal-oil assisted flotation for the gold recovery

    Energy Technology Data Exchange (ETDEWEB)

    Sen, S.; Seyrankaya, A.; Cilingir, Y. [Dokuz Eylul University, Izmir (Turkey). Mining Engineering Department

    2005-09-01

    Using coal-oil agglomeration method for free or native gold recovery has been a research subject for many researchers over the years. In this study, a new approach 'coal-oil assisted gold flotation' was used to recover gold particles. The coal-oil-gold agglomeration process considers the preferential wetting of coal and gold particles. The method takes advantage of the greater hydrophobicity and oleophilicity of coal and gold compared to that the most gangue materials. Unlike the previous studies about coal-oil-gold agglomeration, this method uses a very small amount of coal and agglomerating agents. Some experiments were conducted on synthetic gold ore samples to reveal the reaction of the coal-oil assisted gold flotation process against the size and the number of gold particles in the feed. It was observed that there is no significant difference in process gold recoveries for feeds assaying different Au. Although there was a slight decrease for coarse gold particles, the process seems to be effective for the recovery of gold grains as coarse as 300 {mu} m. The decrease in the finest size ({lt} 53 {mu} m) is considered to be the decrease in the collision efficiency between the agglomerates and the finest gold particles. The effect of changing coal quantity for constant ore and oil amounts was also investigated. The experiments showed that the process gives very similar results for both artificial and natural ore samples; the best results have been obtained by using 30/1 coal-oil ratio.

  15. Kinetics of Cu (II) separation by ion flotation techniques, in cells with flexible spargers

    International Nuclear Information System (INIS)

    Reyes, M.; Tavera, F. J.; Escudero, R.; Patino, F.; Salinas, E.; Rivera, I.

    2010-01-01

    This research studies and experimentally determines the kinetic parameters and effect of modifying the hydrodynamics and chemical conditions of the air-liquid dispersions during the Cu (II) extraction by ion flotation techniques in cells with porous spargers. Results show that the elimination of Cu (II) from solution can be carried out by ion flotation in one stage, obtaining efficiencies of 68% and 56% for the flat and cylindrical sparger respectively with a xanthate concentration of 0,02 g/l. In multistage systems five cells, recoveries over 92 % were achieved for both sparger geometries. The behavior of the flotation apparent kinetic constant is linear to the parameters that characterize dispersion (Jg, eg y Db), until a point is achieved where the process instability makes the system inoperable. The results show that removing base metal ions by ion flotation is strongly affected by the following factors: collector concentration [C], Jg, eg, Db, Jl and Sb. (Author) 20 refs

  16. Thermodynamics of ultra-sonic cavitation bubbles in flotation ore processes

    Science.gov (United States)

    Royer, J. J.; Monnin, N.; Pailot-Bonnetat, N.; Filippov, L. O.; Filippova, I. V.; Lyubimova, T.

    2017-07-01

    Ultra-sonic enhanced flotation ore process is a more efficient technique for ore recovery than classical flotation method. A classical simplified analytical Navier-Stokes model is used to predict the effect of the ultrasonic waves on the cavitations bubble behaviour. Then, a thermodynamics approach estimates the temperature and pressure inside a bubble, and investigates the energy exchanges between flotation liquid and gas bubbles. Several gas models (including ideal gas, Soave-Redlich-Kwong, and Peng-Robinson) assuming polytropic transformations (from isothermal to adiabatic) are used to predict the evolution of the internal pressure and temperature inside the bubble during the ultrasonic treatment, together with the energy and heat exchanges between the gas and the surrounding fluid. Numerical simulation illustrates the suggest theory. If the theory is verified experimentally, it predicts an increase of the temperature and pressure inside the bubbles. Preliminary ultrasonic flotation results performed on a potash ore seem to confirm the theory.

  17. Extraction of a low grade zinc ore using gravity and froth flotation ...

    African Journals Online (AJOL)

    Extraction of a low grade zinc ore using gravity and froth flotation methods. Alabi Oladunni Oyelola, Dalhatu Aboki Abdu, Abere Dare Victor, Magnus T Igonwelundu, Bala Meshack Bosan, Araoye Babatunde Oyebode ...

  18. Effect of some ions in the flotation of phosphorus uraniferous ore from Itataia

    International Nuclear Information System (INIS)

    Claus, O.L.

    1985-01-01

    The influence of several ions in the flotation of phosphorus - uraniferous ore from Itataia were evaluated. Testing with distillated water, water from Itataia region and water prepared in laboratory by nitrate ion addition were done. (E.G.) [pt

  19. Dual effects of sodium sulfide on the flotation behavior of chalcopyrite: I. Effect of pulp potential

    Science.gov (United States)

    Taheri, Bijan; Abdollahy, Mahmoud; Tonkaboni, Sied Ziaedin Shafaei; Javadian, Soheyla; Yarahmadi, Mohammadreza

    2014-05-01

    This study explores the flotation behavior of chalcopyrite in the presence of different concentrations of sodium sulfide (Na2S·9H2O) at pH 12 under controlled potential conditions. It was observed that the flotation of chalcopyrite is not depressed completely when the pulp potential is low, even at high concentrations of sodium sulfide, i.e., 10-1-10-2 mol/L. However, a partial and controlled oxidation of pulp does enhance the effectiveness of sodium sulfide on the depression of chalcopyrite. Characterization of the chalcopyrite particle surface by X-ray photoelectron spectroscopy allowed the identification of hydrophilic and hydrophobic surface species, which are responsible for the depression and flotation of chalcopyrite. Changes in pulp potential were found to be an effective float controlling parameter, by which Na2S can be used to initiate or depress the flotation behavior of chalcopyrite.

  20. Effect of dissolution kinetics on flotation response of calcite with oleate

    Directory of Open Access Journals (Sweden)

    D. G. Horta

    Full Text Available Abstract Phosphate flotation performance can be influenced by the dissolution kinetics of the minerals that compose the ore. The purpose of this work was to investigate the effect of dissolution kinetics on flotation response with oleate (collector of calcites from different origins and genesis. The calcite samples were first purified and characterized by x-ray Fluorescence (XRF and the Rietveld method applied to x-ray Diffractometry data (RXD. Experiments of calcite dissolution and microflotationwere performed at pH 8 and pH 10.The pH effect on the calcite dissolution and flotation indicates the possible influence of the carbonate/bicarbonate ions provided by the CO2 present in the air. In addition, the flotation response is greater as the dissolution increases, making more Ca2+ ions available to interact with collector molecules. This result corroborates the surface precipitation mechanism proposed foroleate adsorption on the calcite surface.

  1. Effect of some column flotation parameters on the fine concentration of phosphate from Itataia, Brazil

    International Nuclear Information System (INIS)

    Reis Junior, J.B.

    1987-01-01

    The present investigation aims, at a higher detail level, to identify, from systematic studies, the most important variables of the column flotation and also to check continuous flotation circuits ntegrating columns and mechanical cells to process the -10μm + 3μm fraction from the Itataia ore. The results obtained with the use of only one column as the rougher stage of direct flotation demonstrated a good selectivity, leading to P 2 O 5 and R 2 O 3 (Fe 2 O 3 + Al 2 O 3 ) grade of 24.2 % and 2.79 %, respectively, with p 2 O 5 recovery of 68.5 %. The results of this investigation indicate that the combination of the column concentrate with that of the conventional flotation circuit increases the overall recovery of P 2 O 5 an U 3 O 5 in 5%, in the physical concentration, without impairing the utilization of the final concentrate. (author) [pt

  2. Effects of particle size and chain length on flotation of quaternary ammonium salts onto kaolinite

    Science.gov (United States)

    Longhua, Xu; Yuehua, Hu; Faqin, Dong; Hao, Jiang; Houqin, Wu; Zhen, Wang; Ruohua, Liu

    2015-06-01

    Effects of particle size and chain length on flotation of quaternary ammonium salts (QAS) onto kaolinite have been investigated by flotation tests. Dodecyltrimethylammonium chloride (DTAC) and cetyltrimethylammonium chloride (CTAC) were used as collectors for kaolinite in different particle size fractions (0.075 ~ 0.01 mm, 0.045 ~ 0.075 mm, 0 ~ 0.045 mm). The anomalous flotation behavior of kaolinite have been further explained based on crystal structure considerations by adsorption tests and molecular dynamics (MD) simulation. The results show that the flotation recovery of kaolinite in all different particle size fractions decreases with an increase in pH. As the concentration of collectors increases, the flotation recovery increases. The longer the carbon chain of QAS is, the higher the recoveries of coarse kaolinite (0.075 ~ 0.01 mm and 0.045 ~ 0.075 mm) are. But the flotation recovery of the finest kaolinite (0 ~ 0.045 mm) decreases with chain lengths of QAS collectors increasing, which is consistent with the flotation results of unscreened kaolinite (0 ~ 0.075 mm). It is explained by the froth stability related to the residual concentration of QAS collector in mineral pulp. In lower residual concentration, the froth stability becomes worse. Within the range of flotation collector concentration, it's easy of CTAC to be completely adsorbed by kaolinite in the particle size fraction (0-0.045 mm), which led to lower flotation recovery. Moreover, it is interesting that the coarser particle size of kaolinite is, the higher flotation recovery is. The anomalous flotation behavior of kaolinite is rationalized based on crystal structure considerations. The results of MD simulations show that the (001) kaolinite surface has the strongest interaction with DTAC, compared with the (00 1) face, (010) and (110) edges. On the other hand, when particle size of kaolinite is altered, the number of basal planes and edge planes is changed. It is observed that the finer kaolinite

  3. Pilot scale direct flotation of a phosphate ore with silicate-carbonate gangue.

    OpenAIRE

    Albuquerque, Rodrigo O.; Peres, Antônio Eduardo Clark; Aquino, José Aury de; Praes, Plínio Eduardo; Pereira, Carlos Alberto

    2012-01-01

    The present pilot scale study addresses the direct flotation route for the concentration of a phosphate ore bearing a silicate-carbonate gangue. The target was to selectively separate apatite from a phosphate ore bearing silicate/carbonate gangue using flotation columns. Based on the results of a previous laboratory scale investigation, a reagents scheme was selected and tested, using, under alkaline conditions, corn starch and a natural collector extracted from the distillation of coconut oi...

  4. Influence of liberation of sulphide minerals on flotation of sedimentary copper ore

    OpenAIRE

    Bakalarz Alicja; Duchnowska Magdalena; Luszczkiewicz Andrzej

    2017-01-01

    Ore liberation is one of the most important parameter in mineral processing, especially in flotation. To separate the valuable components from gangue minerals, it is necessary to liberate one from others. It is achieve primarily through crushing and grinding. These stages are one of the most expensive of mineral production. It is important to determine the adequate mineral liberation which would result in huge savings in the overall cost of flotation plant. The aim of the paper was the analys...

  5. Evaluation of Sulfonate-Based Collectors with Different Hydrophobic Tails for Flotation of Fluorite

    OpenAIRE

    Renji Zheng; Zijie Ren; Huimin Gao; Yupeng Qian

    2018-01-01

    This investigation aims to demonstrate the effects of hydrophobic tails on the affinity and relevant flotation response of sulfonate-based collectors for fluorite. For this purpose, a series of alkyl sulfonates with different hydrophobic tails, namely sodium decanesulfonate (C10), sodium dodecylsulfate (C12), sodium hexadecanesulfonate (C16), and sodium dodecylbenzenesulfonate (C12B) were applied. The flotation tests showed that C12 and C12B had a better collecting performance than C10 and C1...

  6. The effect of fine presence in flotation of phosphate from Itataia-Brazil

    International Nuclear Information System (INIS)

    Dantas, J.O.C.; Adamian, R.

    1987-01-01

    Some important aspects in the flotation of phosphorus-uraniferous ore from Itataia, Brazil, are presented. The effect of particle size and problems caused by the presence of calcite in the gangue which engages the selectivity of the process are studied. The mineral characterization, grinding tests and flotation tests were done. The Kinetic parameters: maximum extrapolated recovery and kinetic constant were calculated. (M.C.K.) [pt

  7. Influence of particle size on the recovery of galene in electro flotation

    International Nuclear Information System (INIS)

    Ntampaka, B.

    1987-01-01

    The difficulties to recovery very small particles by conventional flotation need the development of all methods likely to give the best results. And this owing to the actual tendency which consists in including in the stocks of valorized ores, those with mineral particles finely scattered needing a very advanced grinding. Among these methods (va cum flotation, ionic flotation, column flotation, etc...), the electro flotation, which uses the electrolysis of pulp for it's airing seems to have a great interest but in fortunately its still on a laboratory scale. The passage to the industrial scale needs the putting in a conspicuous position of all possibilities of the method. However the studies have shown that the method should particularly be effective in recovering of several minerals finely ground. In this article, we have confirmed the fact in the case of galene. We have furthermore showed that the rate of recuperation increases with the decreasing of the size of the particles. The recovering is maximal for the particles under μm. This phenomen is different from the one observed in conventional flotation. We have given the reasons of this difference in this article.

  8. Improvement of ore recovery efficiency in a flotation column cell using ultra-sonic enhanced bubbles

    Science.gov (United States)

    Filippov, L. O.; Royer, J. J.; Filippova, I. V.

    2017-07-01

    The ore process flotation technique is enhanced by using external ultra-sonic waves. Compared to the classical flotation method, the application of ultrasounds to flotation fluids generates micro-bubbles by hydrodynamic cavitation. Flotation performances increase was modelled as a result of increased probabilities of the particle-bubble attachment and reduced detachment probability under sonication. A simplified analytical Navier-Stokes model is used to predict the effect of ultrasonic waves on bubble behavior. If the theory is verified by experimentation, it predicts that the ultrasonic waves would create cavitation micro-bubbles, smaller than the flotation bubble added by the gas sparger. This effect leads to increasing the number of small bubbles in the liquid which promote particle-bubble attachment through coalescence between bubbles and micro-bubbles. The decrease in the radius of the flotation bubbles under external vibration forces has an additional effect by enhancing the bubble-particle collision. Preliminary results performed on a potash ore seem to confirm the theory.

  9. Flotation separation of polyvinyl chloride and polyethylene terephthalate plastics combined with surface modification for recycling.

    Science.gov (United States)

    Wang, Chongqing; Wang, Hui; Fu, Jiangang; Zhang, Lingling; Luo, Chengcheng; Liu, Younian

    2015-11-01

    Surface modification with potassium permanganate (KMnO4) solution was developed for separation of polyvinyl chloride (PVC) and polyethylene terephthalate (PET) waste plastics. The floatability of PVC decreases with increasing of KMnO4 concentration, treatment time, temperature and stirring rate, while that of PET is unaffected. Fourier transform infrared (FT-IR) analysis confirms that mechanism of surface modification may be due to oxidization reactions occurred on PVC surface. The optimum conditions are KMnO4 concentration 1.25 mM/L, treatment time 50 min, temperature 60°C, stirring rate 300 r/min, frother concentration 17.5 g/L and flotation time 1 min. PVC and PET with different particle sizes were separated efficiently through two-stage flotation. Additionally, after ultrasonic assisted surface modification, separation of PVC and PET with different mass ratios was obtained efficiently through one-stage flotation. The purity and the recovery of the obtained products after flotation separation are up to 99.30% and 99.73%, respectively. A flotation process was designed for flotation separation of PVC and PET plastics combined with surface modification. This study provides technical insights into physical separation of plastic wastes for recycling industry. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Separation of polyethylene terephthalate from municipal waste plastics by froth flotation for recycling industry

    International Nuclear Information System (INIS)

    Wang, Chong-Qing; Wang, Hui; Liu, You-Nian

    2015-01-01

    Highlights: • Factors of NaOH treatment were studied by orthogonal and single factor experiments. • Mechanism of alkaline treatment for facilitating flotation was manifested. • Flotation separation of PET was achieved with high purity and efficiency. • A flow sheet of purification PET from MWP was designed. - Abstract: Recycling is an effective way to manage plastic wastes and receives considerable attention. Since plastic mixtures are difficult to recycle because of their intrinsic characteristics, separation of mixed plastics is the key problem for recycling. Separation of polyethylene terephthalate (PET) from municipal waste plastics (MWP) by froth flotation combined with alkaline pretreatment was investigated for recycling industry. The effect of process variables was estimated by L 9 (3 4 ) orthogonal array of experiments and single factor experiments. The optimum conditions of alkaline pretreatment are 10 wt% sodium hydroxide, 20 min and 70 °C. After alkaline pretreatment under optimum conditions, flotation separation PET from acrylonitrile–butadiene–styrene, polystyrene, polycarbonate or polyvinyl chloride was achieved with high purity and efficiency. The purity of PET is up to 98.46% and the recovery is above 92.47%. A flow sheet of separation PET from MWP by a combination of froth flotation and sink float separation was designed. This study facilitates industrial application of plastics flotation and provides technical insights into recycling of waste plastics

  11. Ammonia modification for flotation separation of polycarbonate and polystyrene waste plastics.

    Science.gov (United States)

    Wang, Chong-Qing; Wang, Hui; Gu, Guo-Hua; Lin, Qing-Quan; Zhang, Ling-Ling; Huang, Luo-Luo; Zhao, Jun-Yao

    2016-05-01

    A promising method, ammonia modification, was developed for flotation separation of polycarbonate (PC) and polystyrene (PS) waste plastics. Ammonia modification has little effect on flotation behavior of PS, while it changes significantly that of PC. The PC recovery in the floated product drops from 100% to 3.17% when modification time is 13min and then rises to 100% after longer modification. The mechanism of ammonia modification was studied by contact angle, and Fourier transform infrared (FT-IR) and X-ray photoelectron spectroscopy (XPS) measurements. Contact angle of PC indicates the decline of PC recovery in the floated product is ascribed to an increase in surface wettability. FT-IR and XPS spectra suggest that ammonia modification causes chemical reactions occurred on PC surface. Flotation behavior of ammonia-modified PC and PS was investigated with respect to flotation time, frother concentration and particle sizes. Flotation separation of PC and PS waste plastics was conducted based on the flotation behavior of single plastic. PC and PS mixtures with different particle sizes are separated efficiently, implying that the technology possesses superior applicability to particle sizes of plastics. The purity of PS and PC is up to 99.53% and 98.21%, respectively, and the recovery of PS and PC is larger than 92.06%. A reliable, cheap and effective process is proposed for separation of PC and PS waste plastics. Copyright © 2016 Elsevier Ltd. All rights reserved.

  12. Separation of plastics: The importance of kinetics knowledge in the evaluation of froth flotation.

    Science.gov (United States)

    Censori, Matteo; La Marca, Floriana; Carvalho, M Teresa

    2016-08-01

    Froth flotation is a promising technique to separate polymers of similar density. The present paper shows the need for performing kinetic tests to evaluate and optimize the process. In the experimental study, batch flotation tests were performed on samples of ABS and PS. The floated product was collected at increasing flotation time. Two variables were selected for modification: the concentration of the depressor (tannic acid) and airflow rate. The former is associated with the chemistry of the process and the latter with the transport of particles. It was shown that, like mineral flotation, plastics flotation can be adequately assumed as a first order rate process. The results of the kinetic tests showed that the kinetic parameters change with the operating conditions. When the depressing action is weak and the airflow rate is low, the kinetic is fast. Otherwise, the kinetic is slow and a variable percentage of the plastics never floats. Concomitantly, the time at which the maximum difference in the recovery of the plastics in the floated product is attained changes with the operating conditions. The prediction of flotation results, process evaluation and comparisons should be done considering the process kinetics. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Preliminary study on collectorless flotation of chalcocite, bornite and copper-bearing shale in the presence of selected frothers

    OpenAIRE

    Drzymala Jan; Swebodzinska Alicja; Duchnowska Magdalena; Bakalarz Alicja; Luszczkiewicz Andrzej; Kowalczuk Przemyslaw B.

    2016-01-01

    Flotation of carbonaceous copper-bearing shale and copper sulfide minerals such as chalcocite and bornite in the presence of only frother was investigated. It was determined that all investigated solids did not float in pure water in the absence of flotation reagents. However, an addition of a frother rendered both shale and bornite floatable, while the recovery of chalcocite was negligible. These findings suggest that removal of carbonaceous matter from the ore by the so-called pre-flotation...

  14. The effect of process water salinity on flotation of copper ore from Lubin mining region (SW Poland)

    OpenAIRE

    Bakalarz Alicja; Duchnowska Magdalena; Luszczkiewicz Andrzej

    2017-01-01

    The process water used for the flotation of sedimentary copper ore in ore concentration plants in KGHM Polska Miedz S.A. were characterized. The process water used in the flotation circuits is heavily saline. It contains between 25 and 45 g/dm3 of soluble components, and the main constituent, in about 75%, is NaCl. Process water used for flotation consists of reclaimed water from the tailing dam and mine water. The effect of process water salinity on the processes of copper flotation from the...

  15. Optimizing mixing mode and intensity to prevent sludge flotation in sulfidogenic anaerobic sludge bed reactors.

    Science.gov (United States)

    Wang, Bo; Wu, Di; Ekama, George A; Huang, Hao; Lu, Hui; Chen, Guang-Hao

    2017-10-01

    Sludge flotation is a notorious problem in anaerobic wastewater treatment that can occur under various operational conditions and even cause the anaerobic process to completely fail. Despite having been documented for over three decades, its causes and remedies remain elusive, particularly for low-gas-production anaerobic processes such as sulfidogenic and anammox processes. This paper systematically studies sludge flotation in an anaerobic sulfidogenic process for saline domestic sewage treatment. Three lab-scale sulfidogenic reactors were operated in parallel with different modes of mixing (hydraulic, mechanical and pneumatic) at various mixing intensity levels at shear rates ranging from 0.7 to 6.6 s -1 to investigate reactor performance and sludge properties and their relationships with sludge flotation potential. The results indicate that a sulfidogenic reactor with low flotation potential have sludge with low hydrophobicity, low viscosity, and low (more negative) surface charge, while the sludge particle surfaces have high compactness and low roughness. These sludge properties enabled a sludge flotation potential of less than 20% to be maintained. Furthermore, our results show that i) mixing and extracellular polymeric substances (EPS), ii) EPS and sludge properties, and iii) sludge properties and sludge flotation potential are all strongly correlated (all the Spearman's rank correlation coefficients (R s ) are either over 0.64 (if positively correlated) or under -0.64 (if negatively correlated), at the 95% confidence level). Accordingly, sludge flotation can be resolved by controlling reactor mixing. Our findings provide a method to optimize the design and operation of anaerobic sulfidogenic reactors that can be extended to similar low-gas-production anaerobic bioreactors. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Separation of oily materials in radioactive waste waters by flotation. Flotation kinetics; Separacion de materiales oleosos en aguas residuales radiactivas por flotacion. Cinetica de flotacion

    Energy Technology Data Exchange (ETDEWEB)

    Flores E, R.M.; Ortiz O, H.B. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: rosyperus@hotmail.com

    2003-07-01

    The rate of separation of oil and total cobalt in the oleaginous residual water previously treated by coagulation/flocculation with a quaternary ammonium amine (25 mgL{sup -1}) and with modified anionic polyacrylamide (1.5 mgL{sup -1}) (pH = 7, G{sub 1} = 300 s{sup -1} and G{sub 2} = 30 s{sup -1}) was determined. The experimental essays to determine the flotation kinetics, its were carried out using as operation and control parameters the air/solids relationship (G/S 0.35), pressure (P =620 kPa) and volume of air-water mixture (V = 37% of V{sub f}), obtained in previous essays, at two different pressure levels and volume of discharged mixture. The kinetic studies of flotation obtained for the flotation system with conventional air dissolved (DAF) its suggest a first order kinetics that it can be represented by the SCC model. At the same time its show that the separation of the present pollutants in the residual water is governed by the removal velocity of the oil. Meanwhile, the concentration of total Co below 1 mgL{sup -1}, on the other hand, the concentration of the {sup 60} Co at the end of the flotation process resulted smaller than 0.008 Bq/ml, as long as the one {sup 54} Mn were not detectable. (Author)

  17. Comparison of passive fecal flotation run by veterinary students to zinc-sulfate centrifugation flotation run in a diagnostic parasitology laboratory.

    Science.gov (United States)

    Gates, Maureen C; Nolan, Thomas J

    2009-10-01

    The sensitivity of fecal examination methods can be influenced by both technician error and methodology. In this analysis, we compared the results of 335 passive fecal flotation examinations performed on the feces of stray dogs by 3rd-yr veterinary students at the University of Pennsylvania, School of Veterinary Medicine, to the results obtained through zinc-sulfate centrifugation performed by the diagnostic parasitology laboratory on the same fecal samples. The students' passive flotation results agreed with the laboratory zinc-sulfate centrifugation for only 62.4% of samples. Students were able to diagnose 75.0% of Ancylostoma caninum cases, 71.4% of Toxocara canis cases, 54.2% of Trichuris vulpis cases, 26.7% of Cystoisospora spp. (C. ohioensis-like and C. canis) cases, and 14.7% of Giardia lamblia cases. There were also 70 instances where students reported the presence of parasites in the sample that were not diagnosed by zinc-sulfate centrifugation. Based on the overall study findings, passive fecal flotation examinations run in private practice could be missing up to 50.5% of infected dogs, due to either technician error or inherent limitations to the passive fecal flotation technique.

  18. Dissolved Air Flotation for Fiber Removal from Clear Water

    Directory of Open Access Journals (Sweden)

    Bruna Luiza Manago

    2018-02-01

    Full Text Available ABSTRACT We investigated the use of dissolved air flotation (DAF to treat clear water effluent from the paper industry in order to remove fibers. The dosage of polyaluminium chloride (PAC was varied in the following concentrations: 0, 75, 100, 125, 150 and 175 mg/L; as well as bubble rise velocity of 18 and 9 cm/min for two types of paper wastewater: print and gloss. Data were statistically analyzed through factorial arrangement 6x2x2. The treatment of the print paper effluent showed better performance in removing the analyzed parameters with an optimal dosage of 100 mg/L PAC, whereas the gloss paper effluent treatment had satisfactory removal of analyzed parameters with an optimal dosage of 150 mg/L of PAC. This led to the observation that the high efficiency directly obtained with the DAF in conjunction with the use of PAC coagulant was an excellent primary treatment option for effluent resulting from the paper industry.

  19. Flotation and flocculation chemistry of coal and oxidized coals

    Energy Technology Data Exchange (ETDEWEB)

    Somasundaran, P.; Ramesh, R.

    1989-01-01

    This project is designed to develop an understanding of the fundamentals involved in flotation and flocculation of coal, and of coal in various states of oxidation. The main objective of this study is to accurately characterize the coal surface and elucidate mechanisms by which surface interactions between coal and various reagents enhance beneficiation of coals. Effects of oxidation on the modification of surface characteristics of coal by various reagents will also be studied. This quarter, the following studies were conducted in order to further develop our understanding of the role of heterogeneity in interfacial phenomena. (1) Since surface characterization is an important aspect in this project, ESCA (Electron Spectroscopy for Chemical Analysis) study of the coal surface was conducted. Surface derivatization, a technique often used in the preparation of organic compounds for gas-liquid chromatography, uses site specific molecular tags'' that bond to key chemical groups on the surface. Application of derivatization in conjunction with ESCA is a relatively new technique for quantifying functional groups on the surface which has not been possible till now. (2) A distribution of contact angles on the surface of coal (pseudo theta map) is presented based on our earlier results and other published information. The role of heterogeneity in contact angle studies is also examined. 14 refs., 2 tabs.

  20. Electro-coagulation-flotation process for algae removal

    International Nuclear Information System (INIS)

    Gao Shanshan; Yang Jixian; Tian Jiayu; Ma Fang; Tu Gang; Du Maoan

    2010-01-01

    Algae in surface water have been a long-term issue all over the world, due to their adverse influence on drinking water treatment process as well as drinking water quality. The algae removal by electro-coagulation-flotation (ECF) technology was investigated in this paper. The results indicated that aluminum was an excellent electrode material for algae removal as compared with iron. The optimal parameters determined were: current density = 1 mA/cm 2 , pH = 4-7, water temperature = 18-36 deg. C, algae density = 0.55 x 10 9 -1.55 x 10 9 cells/L. Under the optimal conditions, 100% of algae removal was achieved with the energy consumption as low as 0.4 kWh/m 3 . The ECF performed well in acid and neutral conditions. At low initial pH of 4-7, the cell density of algae was effectively removed in the ECF, mainly through the charge neutralization mechanism; while the algae removal worsened when the pH increased (7-10), and the main mechanism shifted to sweeping flocculation and enmeshment. The mechanisms for algae removal at different pH were also confirmed by atomic force microscopy (AFM) analysis. Furthermore, initial cell density and water temperature could also influence the algae removal. Overall, the results indicated that the ECF technology was effective for algae removal, from both the technical and economical points of view.

  1. Determination of molybdenum (VI) in sea water with preliminary concentration by the method of ion flotation

    International Nuclear Information System (INIS)

    Andreeva, I. Yu.; Drapchinskaya, O.L.; Lebedeva, L.I.

    1985-01-01

    The purpose of this paper is to assess the feasibility of using the method of ion flotation for the concentration of microamounts of molybdenum (VI) during determination in sea water. The ion flotation method is used for the purification of industrial sewage from the ions of nonferrous metals, including molybdenum (VI) with its content of up to 50 mg/liter. A 1.10 -4 M solution of sodium molybdate in 0.1M NaOH was used. The effect of different factors on the ion flotation process of molybdenum (VI) was investigated: pH of the solution, flotation times, concentrations of surface-active substances (SAS), molybdenum (IV), extraneous salts. Data presented show that the ion flotation method in conjunction with the photometric method of determining molybdenum with brompyrogallol red (BPR) and cetylpridinium chloride (CP) (limit of detection 0.02 micrograms/liter) allows the content of molybdenum (VI) in sea water to be established with sufficient reliability and reproducibility

  2. A study of the interfacial chemistry of pyrite and coal in fine coal cleaning using flotation

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Chengliang [Univ. of Kentucky, Lexington, KY (United States)

    1993-01-01

    Surface oxidation, surface charge, and flotation properties have been systematically studied for coal, coal-pyrite and ore-pyrite. Electrochemical studies show that coal-pyrite exhibits much higher and more complex surface oxidation than ore-pyrite and its oxidation rate depends strongly on the carbon/coal content. Flotation studies indicate that pyrites have no self-induced floatability. Fuel oil significantly improves the floatability of coal and induces considerable flotation for coal-pyrite due to the hydrophobic interaction of fuel oil with the carbon/coal inclusions on the pyrite surface. Xanthate is a good collector for ore-pyrite but a poor collector for coal and coal-pyrite. The results from thermodynamic calculations, flotation and zeta potential measurements show that iron ions greatly affect the flotation of pyrite with xanthate and fuel oil. Various organic and inorganic chemicals have been examined for depressing coal-pyrite. It was found, for the first time, that sodium pyrophosphate is an effective depressant for coal-pyrite. Solution chemistry shows that pyrophosphate reacts with iron ions to form stable iron pyrophosphate complexes. Using pyrophosphate, the complete separation of pyrite from coal can be realized over a wide pH range at relatively low dosage.

  3. The Effect of Quartz on the Flotation of Fine Wolframite with Octyl Hydroxamic Acid

    Directory of Open Access Journals (Sweden)

    Qingyou Meng

    2017-09-01

    Full Text Available The influence of quartz on the flotation of fine wolframite using octyl hydroxamic acid (OHA as the collector was investigated by micro-flotation tests, inductively coupled plasma (ICP measurements, adsorption experiments, zeta potential, and Fourier transform infrared spectroscopy (FT-IR analysis. Micro-flotation tests showed that a large difference in floatability existed between fine wolframite and quartz in the pH range of 7.0 to 10.0. However, in a synthetic mixture, the flotation separation of fine wolframite from quartz became more difficult as the particle size of the latter decreased. When a dissolved solution of wolframite was used as the flotation medium, quartz floatability improved significantly. Zeta potentials of quartz particles shifted positively in the dissolved solution of wolframite compared to distilled water, especially at a pH level of 7.0–10.0, which was attributed to the metal ions dissolved from the wolframite being adsorbed onto the quartz surface. The surface activation of quartz led to an increase in the OHA adsorption and made the surface hydrophobic. FT-IR analysis further demonstrated that OHA could adsorb onto the activated quartz surface through a dominantly chemical process.

  4. Anglesite and silver recovery from jarosite residues through roasting and sulfidization-flotation in zinc hydrometallurgy.

    Science.gov (United States)

    Han, Haisheng; Sun, Wei; Hu, Yuehua; Jia, Baoliang; Tang, Honghu

    2014-08-15

    Hazardous jarosite residues contain abundant valuable minerals that are difficult to be recovered by traditional flotation process. This study presents a new route, roasting combined with sulfidization-flotation, for the recovery of anglesite and silver from jarosite residues of zinc hydrometallurgy. Surface appearance and elemental distribution of jarosite residues was examined by scanning electron microscopy and energy dispersive X-ray spectrometry analysis, respectively. Decomposition and transformation mechanisms of jarosite residues were illustrated by differential thermal analysis. Results showed that after roasting combined with flotation, the grade and recovery of lead were 43.89% and 66.86%, respectively, and those of silver were 1.3 kg/t and 81.60%, respectively. At 600-700 °C, jarosite was decomposed to release encapsulated valuable minerals such as anglesite (PbSO4) and silver mineral; silver jarosite decomposed into silver sulfate (Ag2SO4); and zinc ferrite (ZnO · Fe2O3) decomposed into zinc sulfate (ZnSO4) and hematite (Fe2O3). Bared anglesite and silver minerals were modified by sodium sulfide and easily collected by flotation collectors. This study demonstrates that the combination of roasting and sulfidization-flotation provides a promising process for the recovery of zinc, lead, and silver from jarosite residues of zinc hydrometallurgy. Copyright © 2014 Elsevier B.V. All rights reserved.

  5. Results of fibre and toner flotation depending on oleic acid dosage.

    Science.gov (United States)

    Trumic, Maja S; Trumic, Milan Z; Vujic, Bogdana; Andric, Ljubisa; Bogdanovic, Grozdanka

    2016-09-01

    The literature was reviewed with respect to deinking flotation methods with toner samples, specifically emphasizing the speciation of copy machine and laser printing, which produce an increasing quantity of paper that is difficult to recycle. Speciation here refers to the physical-chemical characteristics of the toner, which change because of the polymerization (fusion) and oxidation process, due to exposure to heat, light and oxygen (air) during the printing process. To simulate the deinking flotation, after the ideal disintegration process, samples of toner were prepared in order to provide free toner particles. Synthetic toner has iron content and the same physical-chemical features as free disintegrated printed toner particles.We report the toner (I) and fibre (Y) recovery and the brightness (B) of laboratory filter pads formed of deinked product as deinking efficiencies. The application of oleic acid as the collector in the flotation stage gives a better flotation recovery in alkaline than in acidic conditions. The highest brightness (BF = 93.66%) and flotation recoveries (I = 90, Y = 92.82%) were achieved during testing at an oleic acid concentration of 3.38·10(-6) mol l(-1), which is the lowest dose used. This makes the use of oleic acid economical and environmentally friendly. © The Author(s) 2016.

  6. Beneficiation of a Sedimentary Phosphate Ore by a Combination of Spiral Gravity and Direct-Reverse Flotation

    Directory of Open Access Journals (Sweden)

    Xin Liu

    2016-04-01

    Full Text Available In China, direct-reverse flotation is proved to be applicable to most phosphate ores. However, because the ratio of froth product is generally high, current direct-reverse technology faces challenges in terms of high reagent consumptions and cost. A new gravity and flotation combined process has been developed for the recovery of collophanite from sedimentary phosphate ore from the beneficiation plant of Hubei, China. In this process, 53% of the collophanite was firstly recovered by gravity separation, reducing the mass flow to direct flotation. The gravity tailing was the feed for the direct flotation. The flotation concentrate, mixed with gravity concentrate, was then subjected to reverse flotation. A final concentrate with a grade of 30.41% P2O5 at a recovery of 91.5% was produced from the feed analyzing 21.55% P2O5. Compared to the conventional direct-reverse flotation 86.1% recovery at 31.69% P2O5, it was found that pre-recovery of collophanite by spiral separation could significantly reduce the flotation reagent consumption and lead to improved overall collophanite recovery. The benefits of the new process in terms of cost savings were also discussed.

  7. Separation of packaging plastics by froth flotation in a continuous pilot plant.

    Science.gov (United States)

    Carvalho, Teresa; Durão, Fernando; Ferreira, Célia

    2010-11-01

    The objective of the research was to apply froth flotation to separate post-consumer PET (Polyethylene Terephthalate) from other packaging plastics with similar density, in a continuously operated pilot plant. A representative sample composed of 85% PET, 2.5% PVC (Polyvinyl Chloride) and 11.9% PS (Polystyrene) was subjected to a combination of alkaline treatment and surfactant adsorption followed by froth flotation. A mineral processing pilot plant, owned by a Portuguese mining company, was adapted for this purpose. The experimentation showed that it is possible to produce an almost pure concentrate of PET, containing 83% of the PET in feed, in a single bank of mechanical flotation cells. The concentrate grade attained was 97.2% PET, 1.1% PVC and 1.1% PS. By simulation it was shown that the Portuguese recycling industry specifications can be attained if one cleaning and one scavenger stages are added to the circuit. Copyright © 2010 Elsevier Ltd. All rights reserved.

  8. Hemimorphite Flotation with 1-hydroxydodecylidene-1,1-diphosphonic acid and Its Mechanism

    Directory of Open Access Journals (Sweden)

    Wen Tan

    2018-01-01

    Full Text Available 1-hydroxydodecylidene-1,1-diphosphonic acid (HDDPA was prepared and first applied in flotation of hemimorphite. HDDPA exhibited superior flotation performances for recovery of hemimorphite in comparison with lauric acid, and it also possessed good selectivity against quartz flotation under pH 7.0–11.0. Contact angle results revealed that HDDPA preferred to attach on hemimorphite rather than quartz and promoted the hydrophobicity of hemimorphite surfaces. In the presence of HDDPA anions, the zeta potential of hemimorphite particles shifted to more negative value even if hemimorphite was negatively charged, inferring a strong chemisorption of hemimorphite to HDDPA. The Fourier transform infrared (FTIR recommended that HDDPA might anchor on hemimorphite surfaces through bonding the oxygen atoms of its P(=O–O groups with surface Zn(II atoms. X-ray photoelectron spectroscopy (XPS gave additional evidence that the Zn(II-HDDPA surface complexes were formed on hemimorphite.

  9. Utilization of starch graft copolymers as selective depressants for lizardite in the flotation of pentlandite

    Science.gov (United States)

    Cao, Jian; Luo, Yong-Chun; Xu, Guo-Qiang; Qi, Li; Hu, Xiu-Qin; Xu, Peng-Fei; Zhang, Liu-Yi; Cheng, Shao-Yi

    2015-05-01

    This paper investigates the detrimental effect of lizardite surface characteristics on pentlandite flotation. To reduce the effect, two different starch graft copolymers, starch-graft-polyacrylamide (S-g-PAM) and starch-graft-polyacrylic acid (S-g-PAA) were synthesized as depressants for lizardite. The flotation results show that at pH value of 8, where the flotation of lizardite and pentlandite are routinely performed, S-g-PAM and S-g-PAA improve pentlandite recovery efficiently, compared with the traditional depressant carboxymethyl cellulose (CMC). Experimental results demonstrate that S-g-PAM and S-g-PAA disperse the hydrophilic lizardite particles from the pentlandite surface and also flocculate lizardite particles.

  10. Modelling of the dispersed air flotation process applied to dairy wastewater treatment

    Directory of Open Access Journals (Sweden)

    F. P. Puget

    2004-06-01

    Full Text Available The aim of this work was to develop a mathematical model for a continuously operating flotation tank to provide the scale-up and optimization of the separation system. The fluid dynamic of the tank was assumed to be a perfect mixture and the flotation kinetics to be a first-order reaction, as suggested by the batch operation. The experiments were carried out in a continuously operating 60 L tank, used in the treatment of a synthetic dairy waste at its isoelectric point. A mathematical model that describes the behavior of a continuously operating flotation tank used in the treatment of a synthetic dairy waste at its isoelectric point is not only proposed, but also validated with experimental data.

  11. Separation of packaging plastics by froth flotation in a continuous pilot plant

    International Nuclear Information System (INIS)

    Carvalho, Teresa; Durao, Fernando; Ferreira, Celia

    2010-01-01

    The objective of the research was to apply froth flotation to separate post-consumer PET (Polyethylene Terephthalate) from other packaging plastics with similar density, in a continuously operated pilot plant. A representative sample composed of 85% PET, 2.5% PVC (Polyvinyl Chloride) and 11.9% PS (Polystyrene) was subjected to a combination of alkaline treatment and surfactant adsorption followed by froth flotation. A mineral processing pilot plant, owned by a Portuguese mining company, was adapted for this purpose. The experimentation showed that it is possible to produce an almost pure concentrate of PET, containing 83% of the PET in feed, in a single bank of mechanical flotation cells. The concentrate grade attained was 97.2% PET, 1.1% PVC and 1.1% PS. By simulation it was shown that the Portuguese recycling industry specifications can be attained if one cleaning and one scavenger stages are added to the circuit.

  12. Flotation performances and adsorption mechanism of α-hydroxyoctyl phosphinic acid to cassiterite

    Science.gov (United States)

    Li, Fangxu; Zhong, Hong; Zhao, Gang; Wang, Shuai; Liu, Guangyi

    2015-10-01

    In this paper, the flotation performances and adsorption mechanism of α-hydroxyoctyl phosphinic acid (HPA) to cassiterite were investigated by adsorption experiments, micro-flotation tests, zeta potential measurements, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses. The micro-flotation results indicated that compared with styrene phosphonic acid (SPA), diphosphonic acid (DPA), benzohydroxamic acid (BHA) and salicylhydroxamic acid (SHA), HPA exhibited excellent collecting power to cassiterite and superior selectivity against magnetite or hematite over a wide pH range. The results of adsorption experiments and zeta potential deduced that HPA chemisorb on cassiterite surfaces. The results of FTIR inferred HPA chemisorb onto cassiterite surfaces through its P and O atoms with the P-H and O-H bonds broken. XPS analysis further demonstrated HPA react with Sn species by formation of Sn-O-P and Sn-P bond.

  13. Dissolved air flotation and centrifugation as methods for oil recovery from ruptured microalgal cells.

    Science.gov (United States)

    Ghasemi Naghdi, Forough; Schenk, Peer M

    2016-10-01

    Solvent-free microalgal lipid recovery is highly desirable for safer, more sustainable and more economical microalgal oil production. Dispersed air flotation and centrifugation were evaluated for the ability to separate oil and debris from a slurry mixture of osmotically fractured Chaetoceros muelleri cells with and without utilizing collectors. Microalgal oil partially phase-separated as a top layer and partially formed an oil-in-water emulsion. Although collectors, such as sodium dodecyl sulphate enhanced selective flotation, by just adjusting the pH and cell concentration of the mixture, up to 78% of the lipids were recovered in the froth. Using centrifugation of fractured microalgal slurry resulted in removal of 60% cell debris and up to 68.5% of microalgal oil was present in the supernatant. Both methods, centrifugation and flotation provided options for separation of microalgal oil from C. muelleri slurry with similar fatty acid recoveries of 57% and 60%, respectively. Copyright © 2016. Published by Elsevier Ltd.

  14. Preliminary study on collectorless flotation of chalcocite, bornite and copper-bearing shale in the presence of selected frothers

    Directory of Open Access Journals (Sweden)

    Drzymala Jan

    2016-01-01

    Full Text Available Flotation of carbonaceous copper-bearing shale and copper sulfide minerals such as chalcocite and bornite in the presence of only frother was investigated. It was determined that all investigated solids did not float in pure water in the absence of flotation reagents. However, an addition of a frother rendered both shale and bornite floatable, while the recovery of chalcocite was negligible. These findings suggest that removal of carbonaceous matter from the ore by the so-called pre-flotation process can be a suitable procedure to reduce the amount of organic carbon in the concentrates provided that the feed does not contain bornite. Otherwise, simple pre-flotation must be replaced with a more sophisticated process in which flotation of bornite is suppressed.

  15. The effect of process water salinity on flotation of copper ore from Lubin mining region (SW Poland

    Directory of Open Access Journals (Sweden)

    Bakalarz Alicja

    2017-01-01

    Full Text Available The process water used for the flotation of sedimentary copper ore in ore concentration plants in KGHM Polska Miedz S.A. were characterized. The process water used in the flotation circuits is heavily saline. It contains between 25 and 45 g/dm3 of soluble components, and the main constituent, in about 75%, is NaCl. Process water used for flotation consists of reclaimed water from the tailing dam and mine water. The effect of process water salinity on the processes of copper flotation from the Lubin mine area was described. The results of laboratory flotation experiments conducted in tap water and in water of different salinity levels were compared. The effect of the salinity of water within specified concentration limits was generally found to be beneficial for upgrading of the examined ore.

  16. Anglesite and silver recovery from jarosite residues through roasting and sulfidization-flotation in zinc hydrometallurgy

    Energy Technology Data Exchange (ETDEWEB)

    Han, Haisheng; Sun, Wei, E-mail: hanhaishengjingji@126.com; Hu, Yuehua; Jia, Baoliang; Tang, Honghu

    2014-08-15

    Highlights: • Jarosite precipitate hindered the recovery of valuable minerals. • Under 600–700 °C, jarosite decomposed and released the encapsulated valuable minerals. • The bared valuable minerals were easily collected by flotation process. • The new process was promising for dealing with jarosite residues. - Abstract: Hazardous jarosite residues contain abundant valuable minerals that are difficult to be recovered by traditional flotation process. This study presents a new route, roasting combined with sulfidization-flotation, for the recovery of anglesite and silver from jarosite residues of zinc hydrometallurgy. Surface appearance and elemental distribution of jarosite residues was examined by scanning electron microscopy and energy dispersive X-ray spectrometry analysis, respectively. Decomposition and transformation mechanisms of jarosite residues were illustrated by differential thermal analysis. Results showed that after roasting combined with flotation, the grade and recovery of lead were 43.89% and 66.86%, respectively, and those of silver were 1.3 kg/t and 81.60%, respectively. At 600–700 °C, jarosite was decomposed to release encapsulated valuable minerals such as anglesite (PbSO{sub 4}) and silver mineral; silver jarosite decomposed into silver sulfate (Ag{sub 2}SO{sub 4}); and zinc ferrite (ZnO·Fe{sub 2}O{sub 3}) decomposed into zinc sulfate (ZnSO{sub 4}) and hematite (Fe{sub 2}O{sub 3}). Bared anglesite and silver minerals were modified by sodium sulfide and easily collected by flotation collectors. This study demonstrates that the combination of roasting and sulfidization-flotation provides a promising process for the recovery of zinc, lead, and silver from jarosite residues of zinc hydrometallurgy.

  17. Effect of foamability index of short chain alkyl amines on flotation of quartz

    Directory of Open Access Journals (Sweden)

    Szczerkowska Sabina

    2016-01-01

    Full Text Available Amines can be used for flotation of various minerals, especially quartz. The flotation efficiency of quartz depends on the amine type and dose. It was proved that the shorter alkyl amine, higher amine concentration has to be used to recover quartz at the same level. In flotation amines play a role of both collectors and frothers. The ability of a amine to collect particles can be expressed in the form of contact angle, while the foaming properties by different parameters including dynamic foamability index (DFI and critical coalescence concentration (CCC. Determination of DFI and CCC requires advanced techniques and methods. Therefore, in this paper a rapid and facile method for determination of foaming properties of amines and also other surfactants was used. It was based on measuring the initial foam and froth heights in a conventional flotation machine at different concentrations of surfactants. The foam height-concentration curve was described by utilizing an empirical equation which was based on one-adjustable parameter called the foamability index (FI. In this work the foamability index was determined for butylamine (ButNH2, hexylamine (HexNH2 and octylamine (OctNH2 as examples of short chain alkyl amines. The determined foamability indices were 92, 12 and 4 mg/dm3 for ButNH2, HexNH2 and OctNH2, respectively. It was shown that when the flotation results of quartz were presented in the form of recovery versus normalized amine concentration in relation to the foamability index (c/FI, all the experimental data points converged to one curve. It indicates that amines act similarly but at different concentrations expressed as FI. The foamability index seems to be a useful parameter for characterizing any flotation frother.

  18. Coal froth flotation: effects of reagent adsorption on the froth structure

    Energy Technology Data Exchange (ETDEWEB)

    Meryem Ozmak; Zeki Aktas [Ankara University, Ankara (Turkey). Faculty of Engineering, Department of Chemical Engineering

    2006-05-15

    The amount and quality of concentrate obtained from froth flotation of a coal are very important to determine the efficiency of the separation process. The shape and size of the bubbles in the froth directly affect the amount and purity of the concentrate overflowed during the froth flotation of the coal. The froth structure is significantly dependent on parameters such as the size of the solid particles, the surface properties of the particles, the chemical structure of surface active agents, the reagents adsorbed onto solid particles, and the reagents remaining in water. This work was performed to determine the relationship between the reagents adsorbed on the solid particles, froth structure, and froth flotation performance. The -53 {mu}m size fraction of a bituminous coal was used to perform froth flotation experiments. The froth flotation of the coal used was performed in the presence of two nonionic surfactants, Triton x-100 (poly(ethylene glycol) tert-octylphenyl ether) and MIBC (methyl isobutyl carbinol), and an anionic surfactant, SDS (sodium dodecyl sulfate). The results showed that the adsorption of a high amount of reagent on the particles decreased the ability of separation, thus a substantial amount of mineral particles overflowed along with the hydrophobic coal particles. The use of MIBC with Triton x-100 or SDS as mixture increased solid recovery, and it was concluded that MIBC selectively adsorbed on solids acting as collector as well as a frother. Reagent adsorption has a crucial effect on the froth structure, which is strongly related to flotation performance. 33 refs., 18 figs.

  19. A novel process for separation of polycarbonate, polyvinyl chloride and polymethyl methacrylate waste plastics by froth flotation.

    Science.gov (United States)

    Wang, Chong-Qing; Wang, Hui; Huang, Luo-Luo

    2017-07-01

    A novel process was proposed for separation of ternary waste plastics by froth flotation. Pretreatment of plastics with potassium permanganate (KMnO 4 ) solution was conducted to aid flotation separation of polycarbonate (PC), polyvinyl chloride (PVC) and polymethyl methacrylate (PMMA) plastics. The effect of pretreatment parameters including KMnO 4 concentration, treatment time, temperature and stirring rate on flotation recovery were investigated by single factor experiments. Surface treatment with KMnO 4 changes selectively the flotation behavior of PC, PVC and PMMA, enabling separation of the plastics by froth flotation. Mechanism of surface treatment was studied by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and X-ray photoelectron spectrum (XPS). Effect of frother concentration and flotation time on flotation behavior of plastic mixtures was further studied for flotation separation. The optimized conditions for separation of PC are KMnO 4 concentration 2mmolL -1 , treatment time 10min, temperature 60°C, stirring rate 300rpm, flotation time 1min and frother concentration 17.5mgL -1 . Under optimum conditions, PVC and PMMA mixtures are also separated efficiently by froth flotation associated with KMnO 4 treatment. The purity of PC, PVC and PMMA is up to 100%, 98.41% and 98.68%, while the recovery reaches 96.82%, 98.71% and 98.38%, respectively. Economic analysis manifests remarkable profits of the developed process. Reusing KMnO 4 solution is feasible, enabling the process greener. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Laboratory and in situ flotation rates of lecithotrophic eggs from the bathyal echinoid Phormosoma placenta

    Science.gov (United States)

    Young, Craig M.; Cameron, J. Lane

    1987-09-01

    The large, lecithotrophic eggs of the bathyal echinothuriid echinoid Phormosoma placenta are positively buoyant both in vitro and in situ to depths of at least 608 m. Eggs attain terminal velocity in less than 5 cm. At constant salinity, flotation rate is related linearly to temperature; eggs move more slowly at lower temperatures. This effect is attributed to increased water viscosity at lower temperatures, not differential changes in egg and water density. Based on an average flotation velocity of 0.42 cm s -1, it is predicted that eggs produced at bathyal depths will reach the surface in approximately 2 days.

  1. Effects of oxide nanomaterials used in flotation process in wastewater treatment.

    Directory of Open Access Journals (Sweden)

    CRISTINA COVALIU

    2017-05-01

    Full Text Available Important challenges in the global water situation, mainly resulting from worldwide population growth and climate change, require novel innovative water technologies in order to ensure a supply of drinking water and reduce global water pollution. For this purpose, highly advanced nanotechnology offers new opportunities in technological developments for advanced water and wastewater technology processes. This paper presents an important method used in the wastewater treatment and in the mineral separation, named the flotation. Also, this paper presents the factors that influence the froth flotation process, such as: nanoparticle hydrophobicity, nanoparticle diameter, particle softness etc.

  2. Effect of the composition of creosotes on the flotation of coal

    Energy Technology Data Exchange (ETDEWEB)

    Mario Diaz, J.; Sastre, H.; Hernanz, J.F.

    1979-07-01

    The treatment of coal by flotation is influenced by the chemical characteristics of the frother; if creosotes are used, the concentration of phenols seems to be an important factor. In this work the effect of oil and phenols in creosote on the flotation of coal and their ash selectivity is examined. The effect of adding HCl and NaOH for modifying the pH is studied as well. The increase of flotability with major concentration of phenols and the influence of the remaining factors has not been related with the value of contact angles and surface tension which we determined in similar conditions.

  3. Seed flotation and germination of salt marsh plants: The effects of stratification, salinity, and/or inundation regime

    Science.gov (United States)

    Elsey-Quirk, T.; Middleton, B.A.; Proffitt, C.E.

    2009-01-01

    We examined the effects of cold stratification and salinity on seed flotation of eight salt marsh species. Four of the eight species were tested for germination success under different stratification, salinity, and flooding conditions. Species were separated into two groups, four species received wet stratification and four dry stratification and fresh seeds of all species were tested for flotation and germination. Fresh seeds of seven out of eight species had flotation times independent of salinity, six of which had average flotation times of at least 50 d. Seeds of Spartina alterniflora and Spartina patens had the shortest flotation times, averaging 24 and 26 d, respectively. Following wet stratification, the flotation time of S. alterniflora seeds in higher salinity water (15 and 36 ppt) was reduced by over 75% and germination declined by more than 90%. Wet stratification reduced the flotation time of Distichlis spicata seeds in fresh water but increased seed germination from 2 to 16% in a fluctuating inundation regime. Fresh seeds of Iva frutescens and S. alternflora were capable of germination and therefore are non-dormant during dispersal. Fresh seeds of I. frutescens had similar germination to dry stratified seeds ranging 25-30%. Salinity reduced seed germination for all species except for S. alterniflora. A fluctuating inundation regime was important for seed germination of the low marsh species and for germination following cold stratification. The conditions that resulted in seeds sinking faster were similar to the conditions that resulted in higher germination for two of four species. ?? 2009 Elsevier B.V.

  4. The Effects of Calcium Ions on the Flotation of Sillimanite Using Dodecylammonium Chloride

    Directory of Open Access Journals (Sweden)

    Zhijie Chen

    2017-02-01

    Full Text Available The effects of Ca2+ ions on the flotation of sillimanite using dodecylammonium chloride as a collector were investigated by micro-flotation tests, zeta potential measurements, solution chemistry analysis and molecular dynamics (MD simulation. The micro-flotation results indicated that Ca2+ ions remarkably inhibit the flotation of sillimanite in the pH range of 2.0–9.0. The point of zero charge (PZC of sillimanite changed from 5.4 to 6.1 with the addition of Ca2+ ions. Meanwhile, the calculated concentration of RNH3+ in the sillimanite interface layer decreased in the presence of Ca2+ ions. The results of MD simulation revealed that Ca2+ ions have strong binding energy with the sillimanite (010 surface, and the binding energy of RNH3+ with sillimanite (010 surface reduced in the presence of Ca2+ ions. The conclusions drawn from the computations are in good agreement with the experimental results.

  5. Anisotropic surface physicochemical properties of spodumene and albite crystals: Implications for flotation separation

    Science.gov (United States)

    Xu, Longhua; Peng, Tiefeng; Tian, Jia; Lu, Zhongyuan; Hu, Yuehua; Sun, Wei

    2017-12-01

    Aluminosilicate minerals (e.g., spodumene, albite) have complex crystal structures and similar surface chemistries, but they have poor selectivity compared to traditional fatty acid collectors, making flotation separation difficult. Previous research has mainly considered the mineral crystal structure as a whole. In contrast, the surface characteristics at the atomic level and the effects of different crystal interfaces on the flotation behavior have rarely been investigated. This study focuses on investigating the surface anisotropy quantitatively, including the chemical bond characteristics, surface energies, and broken bond densities, using density functional theory and classical theoretical calculations. In addition, the anisotropy of the surface wettability and adsorption characteristics were examined using contact angle, zeta potential, and Fourier-transform infrared measurements. Finally, these surface anisotropies with different flotation behaviors were investigated and interpreted using molecular dynamics simulations, scanning electron microscopy, and X-ray photoelectron spectroscopy. This systematic research offers new ideas concerning the selective grinding and stage flotation of aluminosilicate minerals based on the crystal characteristics.

  6. Performance Recognition for Sulphur Flotation Process Based on Froth Texture Unit Distribution

    Directory of Open Access Journals (Sweden)

    Mingfang He

    2013-01-01

    Full Text Available As an important indicator of flotation performance, froth texture is believed to be related to operational condition in sulphur flotation process. A novel fault detection method based on froth texture unit distribution (TUD is proposed to recognize the fault condition of sulphur flotation in real time. The froth texture unit number is calculated based on texture spectrum, and the probability density function (PDF of froth texture unit number is defined as texture unit distribution, which can describe the actual textual feature more accurately than the grey level dependence matrix approach. As the type of the froth TUD is unknown, a nonparametric kernel estimation method based on the fixed kernel basis is proposed, which can overcome the difficulty when comparing different TUDs under various conditions is impossible using the traditional varying kernel basis. Through transforming nonparametric description into dynamic kernel weight vectors, a principle component analysis (PCA model is established to reduce the dimensionality of the vectors. Then a threshold criterion determined by the TQ statistic based on the PCA model is proposed to realize the performance recognition. The industrial application results show that the accurate performance recognition of froth flotation can be achieved by using the proposed method.

  7. Estimation of bacterial quality of cod fillets with the disc flotation method

    International Nuclear Information System (INIS)

    Boismenu, D.; Lepine, F.; Thibault, C.; Gagnon, M.; Charbonneau, R.; Dugas, H.

    1991-01-01

    Spoilage bacteria of cod fillets were desorbed off the fillet surface by ultrasonication. Catalase activity of these bacteria was determined using the disc flotation method after selective heat inactivation of the endogenous cod catalase and then correlated with the colony forming units. The method was applied to cod fillets from ten retail sources with satisfactory results

  8. The Effect of Seaweed Glue in the Separation of Copper–Molybdenum Sulphide Ore by Flotation

    Directory of Open Access Journals (Sweden)

    Zhixiang Chen

    2018-01-01

    Full Text Available Flotation separation of chalcopyrite from molybdenite was studied using seaweed glue (SEG as a depressant. Flotation process and mechanism were examined by response surface methodology, flotation tests, adsorption tests, zeta potential measurements and fourier transform infrared (FT-IR spectra. Response surface methodology with a Box–Behnken design suggested the optimal reagent schedule: pH 4, depressant seaweed glue 197 mg/L, collector amyl xanthate 16 mg/L and frother (methyl isobutyl carbinol 20 mg/L, and selective separation of chalcopyrite and molybdenite was achieved by flotation. Comparison of SEG and traditional depressants indicated that the SEG could achieve a similar separation efficiency, and exhibited the advantages of environmental compatibility and economic adaptability. Co-adsorption of seaweed glue and amyl xanthate occurred on the surface of molybdenite, and is explained to happen through distinct mechanisms due to the heterogeneous nature of the surface. It is likely that seaweed glue depresses molybdenite by covering the dixanthogen resulting from adsorption of xanthate ions. It is shown that seaweed glue is as effective a depressant of Cu/Mo separation as cyanide.

  9. 46 CFR 28.110 - Life preservers or other personal flotation devices.

    Science.gov (United States)

    2010-10-01

    ... be equipped with at least one immersion suit, exposure suit, or wearable personal flotation device of..., from both the individual's normal work station and berthing area. If there is no location accessible to both the work station and the berthing area, an appropriate device must be stowed in both locations...

  10. Separation of polyethylene terephthalate from municipal waste plastics by froth flotation for recycling industry.

    Science.gov (United States)

    Wang, Chong-Qing; Wang, Hui; Liu, You-Nian

    2015-01-01

    Recycling is an effective way to manage plastic wastes and receives considerable attention. Since plastic mixtures are difficult to recycle because of their intrinsic characteristics, separation of mixed plastics is the key problem for recycling. Separation of polyethylene terephthalate (PET) from municipal waste plastics (MWP) by froth flotation combined with alkaline pretreatment was investigated for recycling industry. The effect of process variables was estimated by L9 (3(4)) orthogonal array of experiments and single factor experiments. The optimum conditions of alkaline pretreatment are 10 wt% sodium hydroxide, 20 min and 70°C. After alkaline pretreatment under optimum conditions, flotation separation PET from acrylonitrile-butadiene-styrene, polystyrene, polycarbonate or polyvinyl chloride was achieved with high purity and efficiency. The purity of PET is up to 98.46% and the recovery is above 92.47%. A flow sheet of separation PET from MWP by a combination of froth flotation and sink float separation was designed. This study facilitates industrial application of plastics flotation and provides technical insights into recycling of waste plastics. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. A Simple Flotation De-Linking Experiment for the Recycling of Paper

    Science.gov (United States)

    Venditti, Richard A.

    2004-01-01

    A laboratory exercise for the flotation de-linking of wastepaper is described, which consists of disintegrating printed wastepaper in a blender and then removing the ink or toner contaminants by pumping air bubbles through suspension using an aquarium pump or other source of air bubbles. The exercise has proven extremely reliable and consistent in…

  12. Flotation of Mineral and Dyes: A Laboratory Experiment for Separation Method Molecular Hitchhikers

    Science.gov (United States)

    Rappon, Tim; Sylvestre, Jarrett A.; Rappon, Manit

    2016-01-01

    Flotation as a method of separation is widely researched and is applied in many industries. It has been used to address a wide range of environmental issues including treatment of wastewater, recovery of heavy metals for recycling, extraction of minerals in mining, and so forth. This laboratory attempts to show how such a simple method can be used…

  13. The Activation Mechanism of Bi3+ Ions to Rutile Flotation in a Strong Acidic Environment

    Directory of Open Access Journals (Sweden)

    Wei Xiao

    2017-07-01

    Full Text Available Lead hydroxyl compounds are known as rutile flotation of the traditional activated component, but the optimum pH range for flotation is 2–3 using styryl phosphoric acid (SPA as collector, without lead hydroxyl compounds in slurry solution. In this study, Bi3+ ions as a novel activator was investigated. The results revealed that the presence of Bi3+ ions increased the surface potential, due to the specific adsorption of hydroxyl compounds, which greatly increases the adsorption capacity of SPA on the rutile surface. Bi3+ ions increased the activation sites through the form of hydroxyl species adsorbing on the rutile surface and occupying the steric position of the original Ca2+ ions. The proton substitution reaction occurred between the hydroxyl species of Bi3+ ions (Bi(OHn+(3−n and the hydroxylated rutile surface, producing the compounds of Ti-O-Bi2+. The micro-flotation tests results suggested that Bi3+ ions could improve the flotation recovery of rutile from 61% to 90%, and from 61% to 64% for Pb2+ ions.

  14. Performance Comparison between Neutralization Tailings and Flotation Tailings Used for Backfill Mix and Mechanism Analysis

    Directory of Open Access Journals (Sweden)

    Bin Han

    2016-01-01

    Full Text Available A comparison test of different tailings used for underground backfill was conducted, using neutralized tailings from BIOX and flotation tailings of Jinfeng Mine. Laboratory comparison test results show that, with neutralized tailings, when the cement dosage is at 19%, backfill UCS after 7 days, 14 days, and 28 days are 105%–163%, 80%–102%, and 33%–43%, respectively, which are higher than those of flotation tailings. When the cement dosage is at 12%, backfill UCS after 7 days, 14 days, and 28 days are 58%–77%, 50%–60%, and 28%–51%, respectively, which are higher than those of flotation tailings. Slurry fluidity of neutralized tailings is lower than that of flotation tailings, while, in these two tailings, the difference of slump and diffusivity values is less than 6%, which is not a significant difference in slurry fluidity. The reason for neutralized tailings showing higher UCS is as follows: during backfill curing, neutralization tailings produce abundant crystals of CaSO4·2H2O in interlaced structure which helps in combining aggregates closely; CaSO4·2H2O hydrates with C3A C4AF contained in the cement and forms clavate cement bacillus which works as a micro reinforcing steel bar. The test proved that neutralized tailings are more optimal for backfilling.

  15. N-(6-(hydroxyamino)-6-oxohexyl) decanamide collector: Flotation performance and adsorption mechanism to diaspore

    Science.gov (United States)

    Deng, Lanqing; Wang, Shuai; Zhong, Hong; Liu, Guangyi

    2015-08-01

    In this paper, a novel surfactant, N-(6-(hydroxyamino)-6-oxohexyl)decanamide (NHOD) was synthesized and used as a collector for flotation separation of diaspore and aluminosilicate minerals. The adsorption mechanism of NHOD onto diaspore was also investigated by FTIR spectra, zeta potential measurement and XPS. The flotation results demonstrated that NHOD exhibited superior collecting power to diaspore and selectivity against kaolinite and illite and could effectively realize flotation recovery of diaspore from bauxite ores contained aluminosilicate minerals under neutral conditions. The results of XPS, FTIR spectra and zeta potential illustrated that at around pH 7.0, NHOD might chemisorb on diaspore surfaces through Alsbnd O coordination bonds formed by binding its sbnd C(dbnd O)NHOH or sbnd C(dbnd O)NHsbnd chelate groups with aluminum atoms on diaspore surfaces. NHOD's unique properties, such as characteristic bond patterns onto diaspore surfaces, two hydrophobic groups, and intermolecular hydrogen bonds between neighboring NHOD molecules coated on diaspore surfaces, rendered it to be a superior flotation collector for diaspore.

  16. Flotation performances and adsorption mechanism of α-hydroxyoctyl phosphinic acid to cassiterite

    Energy Technology Data Exchange (ETDEWEB)

    Li, Fangxu; Zhong, Hong, E-mail: zhongh@csu.edu.cn; Zhao, Gang; Wang, Shuai; Liu, Guangyi, E-mail: guangyi.liu@163.com

    2015-10-30

    Highlights: • Flotation of cassiterite is carried out using a new collector HPA. • Phosphorous and oxygen of HPA forms chelation with Sn. • HPA exhibits good selectivity to cassiterite against magnetite and hematite. • HPA chemisorbs on cassiterite surface by form of Sn–P and Sn–O–P bond. - Abstract: In this paper, the flotation performances and adsorption mechanism of α-hydroxyoctyl phosphinic acid (HPA) to cassiterite were investigated by adsorption experiments, micro-flotation tests, zeta potential measurements, Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) analyses. The micro-flotation results indicated that compared with styrene phosphonic acid (SPA), diphosphonic acid (DPA), benzohydroxamic acid (BHA) and salicylhydroxamic acid (SHA), HPA exhibited excellent collecting power to cassiterite and superior selectivity against magnetite or hematite over a wide pH range. The results of adsorption experiments and zeta potential deduced that HPA chemisorb on cassiterite surfaces. The results of FTIR inferred HPA chemisorb onto cassiterite surfaces through its P and O atoms with the P–H and O–H bonds broken. XPS analysis further demonstrated HPA react with Sn species by formation of Sn–O–P and Sn–P bond.

  17. Synthesis of nanoparticle emulsion collector HNP and its application in microfine chalcopyrite flotation

    Science.gov (United States)

    He, G. C.; Ding, J.; Huang, C. H.; Kang, Q.

    2018-01-01

    Hydrophobic polystyrene nanoparticles bearing thiazole groups named HNP were used as collectors to improve recovery of microfine chalcopyrite in flotation. HNP adsorbs onto microfine particles selectively, which were modified hydrophobically to induce flotation effectively. Particle size and scanning electron microscope analysis for HNP show that HNP is a spherical nano particles with small size, uniform distribution and good dispersion. Infrared spectrum analysis for HNP proved that functional monomer 2-mercapto styrene acrylic thiazole was bonded chemically onto styrene. Flotation test results indicate that HNP is the right collector of chalcopyrite. Especially, the recovery of chalcopyrite is higher than 95% in neutral and acid media. FTIR results reveal that the flotation selectivity of collector HNP is due to strong chemical absorption onto chalcopyrite surface. Zeta potential analysis shows that the zeta potential of chalcopyrite decreased more quickly after interaction with HNP with the increase of pulp pH value, confirming that collector HNP is an anionic collector. Scanning electron microscope conform that HNP has good selective adsorption on chalcopyrite.

  18. Ion Flotation of Copper(II) and Lead(II) from Environmental Water ...

    African Journals Online (AJOL)

    The present study aims to develop a simple, rapid and economic procedure for copper(II) and lead(II) removal under the optimum conditions investigated. It is based on the complex formation between Cu2+ and Pb2+ ions and diphenylcarbazone (HDPC) followed by flotation with oleic acid (HOL) surfactant. The different ...

  19. Testing of pyrite flotation techniques on selected Ohio coals: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Arnold, B. J.; Torak, E. R.

    1989-05-01

    The project was conceived to demonstrate the combining of conventional physical coal cleaning with emerging advanced physical coal cleaning technologies in a cost-effective manner. The objectives of the program were to demonstrate that conventional coal cleaning followed by advanced coal cleaning of a crushed mid-gravity portion of the run-of-mine coal would produce a clean coal, suitable for use as a thermal coal, having a lower ash content and a lower sulfur dioxide emission potential than a coal cleaned only be current conventional cleaning technologies. As part of this program a number of advanced flotation techniques were tested to determine the feasibility of including them in the design of their Advanced Coal Preparation Facility. The program consisted of testing the Pittsburgh seam, the Middle Kittanning seam, and the Meigs Creek seam coals in the pilot flotation circuit at EPRI's Coal Quality Development Center (CQDC) in Homer City, Pennsylvania. This report contains all the data from OCDO's pilot flotation test program at the CQDC and the test data from the Middle Kittanning and Meigs Creek reverse flotation tests. 13 figs., 40 tabs.

  20. Laboratory-and mill-scale study of surfactant spray flotation deinking

    Science.gov (United States)

    Greg Delozier; Yulin Zhao; Yulin Deng; David White; Junyong Zhu; Mark Prein

    2005-01-01

    As the cost of quality waste paper continues to escalate in response to an increased global demand for this finite resource, loss of saleable fiber within flotation rejects becomes both environmentally and economically unacceptable. The ability of surfactant spray technology to reduce fiber loss without detriment to pulp brightness gains has been demonstrated during...

  1. Optimization of chemical composition in the manufacturing process of flotation balls based on intelligent soft sensing

    Directory of Open Access Journals (Sweden)

    Dučić Nedeljko

    2016-01-01

    Full Text Available This paper presents an application of computational intelligence in modeling and optimization of parameters of two related production processes - ore flotation and production of balls for ore flotation. It is proposed that desired chemical composition of flotation balls (Mn=0.69%; Cr=2.247%; C=3.79%; Si=0.5%, which ensures minimum wear rate (0.47 g/kg during copper milling is determined by combining artificial neural network (ANN and genetic algorithm (GA. Based on the results provided by neuro-genetic combination, a second neural network was derived as an ‘intelligent soft sensor’ in the process of white cast iron production. The proposed ANN 12-16-12-4 model demonstrated favourable prediction capacity, and can be recommended as a ‘intelligent soft sensor’ in the alloying process intended for obtaining favourable chemical composition of white cast iron for production of flotation balls. In the development of intelligent soft sensor data from the two real production processes was used. [Projekat Ministarstva nauke Republike Srbije, br. TR35037 i br. TR35015

  2. Coagulation of fines in fluorite froth flotation; Coagulacion de finos en la flotacion de la fluorita

    Energy Technology Data Exchange (ETDEWEB)

    Sarquis, P. E.; Gonzalez, M.; Moyano, A.; Bazan, V.

    2011-07-01

    Fluorite, a valuable mineral in the metallurgical industry, can be found together with silicates, carbonates and oxides in ore deposits. Commercial concentrates with more than 95 % of CaF{sub 2} are obtained processing the mineral in flotation plants and using oleic acid as fluorite collector. Depressor reagents such as sodium silicate, tannin and sodium carbonate are commonly employed to allow the oleic acid selective performance. These reagents cause a dispersant effect separating the solid-liquid solution on tailing plants. Fine particles in the recovered water enter the circuit and affect the flotation efficiency. The effect of coagulant ions was studied as a method to clarify the returned water. The problem of the presence of these ions is related to its reactions with the collector by the formation of compounds and possibly on the selectivity. Variable quantities of Al{sup 3}+, Fe{sup 3}+ and Ca{sup 2}+ ions were added to the flotation to evaluate its effect on the fluorite recovery, in the selectivity and in solids content in recirculation water. Results show that some ions fail to improve water quality and are detrimental to flotation. On the contrary, some ions contribute to reduce fine content in suspension. Therefore, although there is a recovery reduction, such effect can be counteracted increasing the collector consumption a little. (Author) 21 refs.

  3. Beneficiation of low grade graphite ore of eastern India by two-stage grinding and flotation

    Directory of Open Access Journals (Sweden)

    Vasumathi N.

    2014-01-01

    Full Text Available A low grade graphite run-of-mine (r.o.m ore from eastern India was studied for its amenability to beneficiation by flotation technique. The petrography studies indicate that the ore primarily consists of quartz and graphite with minor quantity of mica. It analyzed 89.89% ash and 8.59% fixed carbon. The ore was crushed in stages followed by primary coarse wet grinding to 212 μm (d80. Rougher flotation was carried out in Denver flotation cell to eliminate gangue as much as possible in the form of primary tailings with minimal loss of carbon. Diesel & pine oil were used as collector and frother respectively. Regrinding of rougher concentrate to150 μm (d80 was resorted to further liberate the graphite values and was followed by multi-stage cleaning. This two-stage grinding approach involving a primary coarse grinding and regrinding of rougher float followed by its multi-stage cleaning was found to yield required grade of concentrate for applications such as refractories, batteries and high temperature lubricants. This approach is supposed to retain the flake size of coarse, free and liberated graphite, if available, during primary coarse grinding and rougher flotation stage with minimal grinding energy costs as against the usual practice of single stage grinding in the case of many ores. A final concentrate of 8.97% weight recovery with 5.80% ash and 92.13% fixed carbon could be achieved.

  4. Treatment and Recycling of the Process Water in Iron Ore Flotation of Yuanjiacun Iron Mine

    Directory of Open Access Journals (Sweden)

    Wen-li Jiang

    2017-01-01

    Full Text Available Coagulating sedimentation and oxidation treatment of process water in iron ore flotation of Yuanjiacun iron mine had been studied. The process water of this mine carried residual polyacrylamide (PAM, poly(diallyldimethylammonium chloride (PDADMAC, and Ca2+ from the flotation and caused decrease of the iron flotation recovery or grade of the concentrate. The studies on high-intensity magnetic separation (HIMS tailings for coagulating sedimentation showed that the settling performance of coagulant (named CYH was better than that of PDADMAC. The analyses of FTIR spectra and zeta potential demonstrated that CYH is adsorbed mainly through electrostatic attraction onto HIMS tailings. Sodium hypochlorite was adopted to oxidize the residual organics in tailings wastewater. When sodium hypochlorite is at the dosage of 1.0 g/L, reaction temperature is of 20°C, and reaction time is of 30 minutes, the removal rates of PAM, COD, and Ca2+ were 90.48%, 83.97%, and 85.00%, respectively. Bench-scale flotation studies on the treated tailings wastewater indicated that the iron recovery and grade of concentrate were close to those of freshwater.

  5. Application of pyrolysis residue from waste materials in black coal flotation

    Czech Academy of Sciences Publication Activity Database

    Fečko, P.; Kašpárková, A.; Pertile, E.; Kříž, Vlastimil; Tora, B.; Jarosinski, A.; Janáková, I.

    2010-01-01

    Roč. 12, č. 2 (2010), s. 62-66 ISSN 1509-8117 Institutional research plan: CEZ:AV0Z30460519 Keywords : flotation * black coal * pyrolysis Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 0.333, year: 2010

  6. Separation of plastics by froth flotation. The role of size, shape and density of the particles.

    Science.gov (United States)

    Pita, Fernando; Castilho, Ana

    2017-02-01

    Over the last few years, new methods for plastic separation in mining have been developed. Froth flotation is one of these techniques, which is based on hydrophobicity differences between particles. Unlike minerals, most of the plastics are naturally hydrophobic, thus requiring the addition of chemicals that promote the selective wettability of one of its components, for a flotation separation. The floatability of six granulated post-consumer plastic - Polystyrene (PS), Polymethyl methacrylate (PMMA), Polyethylene Terephthalate (PET-S, PET-D) and Polyvinyl Chloride (PVC-M, PVC-D) - in the presence of tannic acid (wetting agent), and the performance of the flotation separation of five bi-component plastic mixtures - PS/PMMA, PS/PET-S, PS/PET-D, PS/PVC-M and PS/PVC-D - were evaluated. Moreover, the effect of the contact angle, density, size and shape of the particles was also analysed. Results showed that all plastics were naturally hydrophobic, with PS exhibiting the highest floatability. The contact angle and the flotation recovery of six plastics decreased with increasing tannic acid concentration, occurring depression of plastics at very low concentrations. Floatability differed also with the size and shape of plastic particles. For regular-shaped plastics (PS, PMMA and PVC-D) floatability decreased with the increase of particle size, while for lamellar-shaped particles (PET-D) floatability was slightly greater for coarser particles. Thus, plastic particles with small size, lamellar shape and low density present a greater floatability. The quality of separation varied with the mixture type, depending not only on the plastics hydrophobicity, but also on the size, density and shape of the particles, i.e. the particle weight. Flotation separation of plastics can be enhanced by differences in hydrophobicity. In addition, flotation separation improves if the most hydrophobic plastic, that floats, has a lamellar shape and lower density and if the most hydrophilic

  7. Sensitivity of double centrifugation sugar fecal flotation for detecting intestinal helminths in coyotes (Canis latrans).

    Science.gov (United States)

    Liccioli, Stefano; Catalano, Stefano; Kutz, Susan J; Lejeune, Manigandan; Verocai, Guilherme G; Duignan, Padraig J; Fuentealba, Carmen; Ruckstuhl, Kathreen E; Massolo, Alessandro

    2012-07-01

    Fecal analysis is commonly used to estimate prevalence and intensity of intestinal helminths in wild carnivores, but few studies have assessed the reliability of fecal flotation compared to analysis of intestinal tracts. We investigated sensitivity of the double centrifugation sugar fecal flotation and kappa agreement between fecal flotation and postmortem examination of intestines for helminths of coyotes (Canis latrans). We analyzed 57 coyote carcasses that were collected between October 2010 and March 2011 in the metropolitan area of Calgary and Edmonton, Alberta, Canada. Before analyses, intestines and feces were frozen at -80 C for 72 hr to inactivate Echinococcus eggs, protecting operators from potential exposure. Five species of helminths were found by postmortem examination, including Toxascaris leonina, Uncinaria stenocephala, Ancylostoma caninum, Taenia sp., and Echinococcus multilocularis. Sensitivity of fecal flotation was high (0.84) for detection of T. leonina but low for Taenia sp. (0.27), E. multilocularis (0.46), and U. stenocephala (0.00). Good kappa agreement between techniques was observed only for T. leonina (0.64), for which we detected also a significant correlation between adult female parasite intensity and fecal egg counts (R(s)=0.53, P=0.01). Differences in sensitivity may be related to parasite characteristics that affect recovery of eggs on flotation. Fecal parasitologic analyses are highly applicable to study the disease ecology of urban carnivores, and they often provide important information on environmental contamination and potential of zoonotic risks. However, fecal-based parasitologic surveys should first assess the sensitivity of the techniques to understand their biases and limitations.

  8. Separation of polyvinyl chloride (PVC) from automobile shredder residue (ASR) by froth flotation with ozonation

    International Nuclear Information System (INIS)

    Reddy, Mallampati Srinivasa; Kurose, Keisuke; Okuda, Tetsuji; Nishijima, Wataru; Okada, Mitsumasa

    2007-01-01

    The purpose of this study is to develop froth flotation to separate polyvinyl chloride (PVC) from automobile shredder residue (ASR) plastic mixtures of variable composition. Some polymers in ASR polymer mixtures have similar density and hydrophobicity with PVC and thus selective flotation of PVC from ASR polymer mixtures cannot be achieved. The present study focused on the surface modification of PVC with ozonation, and then the modified PVC can be separated from other polymers by the following froth flotation. The results of this study indicate that the selective recovery of PVC from real ASR polyethylene tetra pethelate (PET), polymethyl methacrylate (PMMA), polybutyl methacralate (PBMA), ethyl acrylate (EA), polycarbonate (PC) and rubber mixtures can be accomplished in a three-step process involving a gravity separation, ozonation and froth flotation. The rubber was removed from other heavy ASR (PVC, PET, PMMA, PBMA, EA and PC) polymers by froth flotation without mixing. It was found that ozonation process produced the desired difference in contact angle required (from 89.5 to 73.0 o ) for separation of PVC from other heavy ASR polymers, whereas the contact angles of other polymers was slightly decreased. The most of the load ASR, i.e. about 72.4% is floated away and 27.6% was settled down. The highest component 96.7% of PVC was recovered in the settled fraction. As a result of this research effort, the surface modification of PVC with ozonation can be efficiently useful to separate the PVC from other similar density ASR mixed polymers

  9. Recovery of copper ion by flotation with potassium amylxanthate; Recuperacion de iones cobre por flotacion con amilxantato de potasio

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez-Serrano, B.; Coello-Velazquez, A. L.; Bernardo, A.; Afif, E.; Menendez-Aguado, J. M.

    2012-11-01

    In this paper a study about the column flotation process of copper ion employing potassium amylxanthate as collector reagent is carried out. The effect on the recovery of copper ion by the modification of variables such as collector/metal relation and surface velocity of gas and liquid was determined experimentally by the analysis of the statistic-mathematical model of the copper flotation process, as well as the physico-chemical phenomena that take place, showing the effect of the collector/metal relation in the process. The effect of pH as the main properties of the chemical system in the recovery and the kinetic of the flotation process is made too. The experimental results shows that the recovery of copper in the pH range of 4,5 - 12 is possible with prevalence of precipitate flotation. (Author) 43 refs.

  10. Feasibility of flotation concentration of fungal spores as a method to identify toxigenic mushrooms

    Directory of Open Access Journals (Sweden)

    Bazzle LJ

    2014-12-01

    Full Text Available Lisa J Bazzle,1 Marc A Cubeta,2 Steven L Marks,1 David C Dorman3 1Department of Clinical Sciences, College of Veterinary Medicine, 2Department of Plant Pathology, College of Agriculture and Life Sciences, Center for Integrated Fungal Research, 3Department of Molecular and Biomedical Sciences, College of Veterinary Medicine, North Carolina State University, Raleigh, NC, USA Purpose: Mushroom poisoning is a recurring and challenging problem in veterinary medicine. Diagnosis of mushroom exposure in animals is hampered by the lack of rapid diagnostic tests. Our study evaluated the feasibility of using flotation concentration and microscopic evaluation of spores for mushroom identification. Evaluation of this method in living animals exposed to toxigenic mushrooms is limited by ethical constraints; therefore, we relied upon the use of an in vitro model that mimics the oral and gastric phases of digestion. Methods: In our study, mycologist-identified toxigenic (poisonous and nontoxigenic fresh mushrooms were collected in North Carolina, USA. In phase 1, quantitative spore recovery rates were determined following magnesium sulfate, modified Sheather's sugar solution, and zinc sulfate flotation (n=16 fungal species. In phase 2, mushrooms (n=40 fungal species were macerated and digested for up to 2 hours in a salivary and gastric juice simulant. The partially digested material was acid neutralized, filtered, and spores concentrated using zinc sulfate flotation followed by microscopic evaluation of spore morphology. Results: Mean spore recovery rates for the three flotation fluids ranged from 32.5% to 41.0% (P=0.82. Mean (± standard error of the mean Amanita spp. spore recovery rates were 38.1%±3.4%, 36.9%±8.6%, and 74.5%±1.6% (P=0.0012 for the magnesium sulfate, Sheather's sugar, and zinc sulfate solutions, respectively. Zinc sulfate flotation following in vitro acid digestion (phase 2 yielded spore numbers adequate for microscopic visualization in

  11. Cleansing of oil-contaminated soils using flotation; Depollution par flottation de sols contamines par des huiles

    Energy Technology Data Exchange (ETDEWEB)

    Niewiadomski, M.; Nalaskowski, J. [Universite de l' Utah, Salt Lake City, UT (United States); Hupka, J.; Miller, J.D. [Universite Technique de Gdansk (Poland)

    2001-03-01

    Cleansing of oil contaminated soils using flotation is performed in two steps: removal of the oil from the soil, and separation of the obtained emulsion using flotation. Tests have been performed to determine the optimum operating conditions of both steps using a contaminated sand in suspension with ionic and non-ionic activators, and with and without the use of ultrasounds. Abstract only. (J.S.)

  12. Effect of inorganic and organic depressants on the cationic flotation and surface charge of rhodonite-rhodochrosite

    OpenAIRE

    Duarte, Renata Santos; Lima, Rosa Malena Fernandes; Leão, Versiane Albis

    2015-01-01

    Abstract Silicates (rhodonite, tephroite, spessartine) and the carbonate (rhodochrosite) of manganese are of economic interest in silicate-carbonated manganese ores. The recovery of both mineral classes by flotation constitutes a challenge; rhodochrosite is a slightly soluble mineral that can release Mn2+ ions in pulp. In this work, the effects of inorganic and organic depressants on the cationic flotation at pH 10 with ether amine acetate and the surface charges of rhodonite and rhodochrosit...

  13. Adsorption of surfactants and polymers on iron oxides:implications for flotation and agglomeration of iron ore

    OpenAIRE

    Potapova, Elisaveta

    2011-01-01

    Iron ore pellets are an important refined product used as a raw material in the production of steel. In order to meet the requirements of the processes for iron production, the iron ore is upgraded in a number of steps including, among others, reverse flotation. Under certain circumstances the flotation collector may inadvertently adsorb on the iron ore particles increasing the hydrophobicity of the iron ore concentrate, which in turn has been shown to have an adverse effect on pellet strengt...

  14. Separation of rare-earth (RE) ions by flotation with the aid of citric acid and hexadecylamine

    International Nuclear Information System (INIS)

    Skrylev, L.D.; Sazonova, V.F.; Pavlenko, S.N.; Karpenko, L.I.

    1989-01-01

    The aim of the present work was to develop further the flotation method for separating RE ions, namely, to examine the possibility of separating Re ions by converting them into citrate complexes and subsequently binding them with the aid of hexadecylamine in difficultly soluble and easily floatable compounds, sublates. Thus, these investigations showed that it is possible in principle to separate RE ions by conversion into citrate complexes followed by flotation separation of the latter from solutions with the aid of hexadecylamine

  15. Separation of unburned carbon from coal fly ash through froth flotation; Sekitanbai no shisshiki datsutanso gijutsu kaihatsu shiken

    Energy Technology Data Exchange (ETDEWEB)

    Miwa, T. [Center for Coal Utilization, Japan, Tokyo (Japan); Murakami, T. [The Coal Mining Research Center, Japan, Tokyo (Japan)

    1996-09-01

    Coal ash tends to become containing more unburned carbon and porous substances depending on conditions of combustion, whose adverse effects to products due to water adsorbability, absorbability and color tones create obstacles in its utilization. Therefore, research and development works have been progressed on wet type carbon removing technology which is characterized in that coal is pulverized to preferable degrees and subjected to flotation. This paper reports the results obtained during fiscal 1995. The results may be summarized as follows: as a result of the comparison test on a column flotation machine and an FW type flotation machine of machine stirring type, the former machine showed better flotation efficiency; several methods were investigated on crushing as a treatment prior to flotation, whereas a mixer with greater circumferential speed and a homo mixer showed the highest efficiency; strength of the impact to the flotation efficiency was found to decrease in the order of pulp concentration > pretreatment time > collector addition ratio; and as a result of the evaluation on refined ash as a cement admixture and carbons as fuel, possibilities were found in them for practical application. 16 figs., 2 tabs.

  16. High precision density comparison measurement of silicon crystals by the pressure of flotation method

    Science.gov (United States)

    Waseda, A.; Fujii, K.

    2001-12-01

    The development of a new density comparison measurement system for silicon crystals using the pressure of flotation method (PFM) is described. The effective isothermal compressibility of a flotation liquid mixture of 1,2,3-tribromopropane and 1,2-dibromoethane is obtained. Density comparison measurements are presented for silicon spheres of mass 1 kg from the National Research Laboratory of Metrology (NRLM) for the density standard and the determination of the Avogadro constant. The combined relative uncertainty of PFM density comparison measurement for S4 and S5 NRLM silicon spheres is 5×10-8. Adjusted densities are calculated from the comparison and absolute measurements based on a least-squares analysis through a matrix formulation.

  17. Flotation in column applied to fines of the Itataia phosphoro-uraniferous ore, CE, Brazil

    International Nuclear Information System (INIS)

    Furtado, J.R.V.; Peres, A.E.C.

    1985-01-01

    An adequate process to treat the fine fraction was developed in the present investigation, after size and chemical characterization of the fines,. Emphasis was placed on construction, assembling and operation of a 5.2 cm diameter and 6.0 m high continuos flotation column. The column was fed with the pilot plant desliming cyclone overflow, below 10 m. Tests were also carried out with the underflow of the same cyclone and with the very fine underflow of a 20 mm cyclone. The column presented a better performance than a rougher laboratory mechanical cell when tested with the underflow of 20 mm cyclone. Concentrates with 24.5% P 2 O 5 , with recovery levels above 60% were achieved from feed grades of 10.3%P 2 O 5 , it is worth mentioning that the rougher flotation reagents scheme is not effective to deppress carbonatic gangue irrespective of the size range. (Author) [pt

  18. A novel method to harvest Chlorella sp. by co-flocculation/air flotation.

    Science.gov (United States)

    Zhang, Haiyang; Lin, Zhe; Tan, Daoyong; Liu, Chunhua; Kuang, Yali; Li, Zhu

    2017-01-01

    To develop a more effective dissolved air flotation process for harvesting microalgae biomass, a co-flocculation/air flotation (CAF) system was developed that uses an ejector followed by a helix tube flocculation reactor (HTFR) as a co-flocculation device to harvest Chlorella sp. 64.01. The optimal size distribution of micro-bubbles and an air release efficiency of 96 % were obtained when the flow ratio of inlet fluid (raw water) to motive fluid (saturated water) of the ejector was 0.14. With a reaction time of 24 s in the HTFR, microalgae cells and micro-bubbles were well flocculated, and these aerated flocs caused a fast rising velocity (96 m/h) and high harvesting efficiency (94 %). In a CAF process, micro-bubbles can be encapsulated into microalgae flocs, which makes aerated flocs more stable. CAF is an effective approach to harvesting microalgae.

  19. Taguchi optimization: Case study of gold recovery from amalgamation tailing by using froth flotation method

    Science.gov (United States)

    Sudibyo, Aji, B. B.; Sumardi, S.; Mufakir, F. R.; Junaidi, A.; Nurjaman, F.; Karna, Aziza, Aulia

    2017-01-01

    Gold amalgamation process was widely used to treat gold ore. This process produces the tailing or amalgamation solid waste, which still contains gold at 8-9 ppm. Froth flotation is one of the promising methods to beneficiate gold from this tailing. However, this process requires optimal conditions which depends on the type of raw material. In this study, Taguchi method was used to optimize the optimum conditions of the froth flotation process. The Taguchi optimization shows that the gold recovery was strongly influenced by the particle size which is the best particle size at 150 mesh followed by the Potassium amyl xanthate concentration, pH and pine oil concentration at 1133.98, 4535.92 and 68.04 gr/ton amalgamation tailing, respectively.

  20. Characterization and potential application of pataua vegetable oil in apatite flotation

    International Nuclear Information System (INIS)

    Oliveira, P.S. de; Mansur, H.S.; Peres, A.E.C.

    2016-01-01

    The present research characterizes the Pataua palm (Oenocarpus bataua) oil regarding to its fatty acids profile and acidity index, and evaluates its use for apatite flotation. The Pataua oil evaluated is unsaturated e predominantly composed of cis-9-octadecenoic acid (oleic acid). The mineral sample characterization revealed a material composed by a fluoroapatite deficient in fluorine, a possibly result of isomorphic substitution, and with quartz and monazite inclusions. The analysis of the mineral after reagent conditioning, by Fourier Transform Infrared Spectroscopy (FTIR), pointed to the presence of characteristic bands of carbon chains and carboxylate group, suggesting the collector adsorption through the mechanisms of chemisorption and insoluble calcium salts precipitation. Thus, it is proposed the Pataua oil potential use in flotation systems aiming apatite recovery. (author)

  1. Evaluation of sorptive flotation technique for enhanced removal of radioactive Eu(III) from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Ezzat, Amir; Saad, Ebtissam A. [Ain Shams Univ., Cairo (Egypt). Chemistry Dept.; Mahmoud, Mamdoh R. [Atomic Energy Authority, Cairo (Egypt). Nuclear Chemistry Dept.; Soliman, Mohamed A. [Atomic Energy Authority, Cairo (Egypt). Egypt Second Research Reactor; Kandil, Abdelhakim [Helwan Univ., Cairo (Egypt). Chemistry Dept.

    2017-06-01

    The present study aims at the removal of Eu(III) from aqueous solutions by sorptive flotation process. This process involves adsorption of Eu(III) onto bentonite and kaolinite clays followed by floatation using sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB) collectors. The effect of adsorption parameters (pH, contact time, clay weight, Eu(III) concentration, ionic strength) as well as flotation parameters (collector and frother concentrations, bubbling time, concentrations of foreign cations and anions) on the removal efficiency of Eu(III) were studied. The obtained results show that Eu(III) ions are removed efficiently (R% ∝ 95%) at pH=4 after 1 h shaking with clay and 15 min floatation. The adsorption kinetics of Eu(III) onto the employed clays followed the pseudo-second-order model and the equilibrium data fitted well to the Freundlich isotherm model.

  2. A study on the effects of ozone dosage on dissolved-ozone flotation (DOF) process performance.

    Science.gov (United States)

    Jin, Xin; Jin, Pengkang; Wang, Xiaochang

    2015-01-01

    Dissolved-ozone flotation (DOF) is a tertiary wastewater treatment process, which combines ozonation and flotation. In this paper, a pilot-scale DOF system fed by secondary effluent from a wastewater treatment plant (WWTP) in China was used to study the effect of ozone dosage on the DOF process performance. The results show that an ozone dosage could affect the DOF performance to a large extent in terms of color and organic matter removal as well as disinfection performance. The optimal color and organic matter removal was achieved at an ozone dosage of 0.8 mg/l. For disinfection, significant improvement in performance could be achieved only when the organic matter removal was optimal. The optimal ozone dosage of at least 1.6 mg/l was put forward, in this case, in order to achieve the optimal color, turbidity, organic matter and disinfection performance.

  3. Ionic flotation of uranium and of cadmium in concentrated phosphoric acid media

    International Nuclear Information System (INIS)

    Jdid, E.; Bessiere, J.; Blazy, P.

    1984-01-01

    The ionic flotation technique has been applied to concentrated phosphoric acid media (with 30% P 2 O 5 or H 3 PO 4 5.5 M) as a new process for the recovery of uranium and the elimination of cadmium. The results obtained seem to indicate that in these hyperacid media the anionic collectors are better suited than the cationic collectors and that they then permit the flotation of the uranium and cadmium ions with a very rapid kinetics and the achievement of efficiencies of over 90%. In the case of uranium, the collector used remains efficient up to a temperature of 60 0 C with a satisfactory selectivity in the face of others cations present in the commercial phosphoric acid, and which have a penalizing effect on the uraniferous concentrates, and the floated uranium concentrate assays approximately 10% U on a dry basis [fr

  4. Effect of Oxygen and Micro-Cracking on the Flotation of Low Grade Nickel Sulphide Ore

    OpenAIRE

    Edison Muzenda; Ayo S Afolabi

    2010-01-01

    This study investigated the effect of oxygen and micro-cracking on the flotation of low grade nickel sulphide ore. The ore treated contained serpentine minerals which have a history of being difficult to process efficiently. The use of oxygen as a bubbling gas has been noted to be effective because it increases the pulp potential. The desired effect of micro cracking the ore is that the nickel sulphide minerals will become activated and this activation will render these m...

  5. Bench scale flotation of spodume/quartz and lepidolite/quartz synthetic mixtures

    International Nuclear Information System (INIS)

    Valadao, G.E.S.; Gontijo, C.F.; Peres, A.E.C.

    1985-01-01

    Based on results of zeta potential determinations and microflotation tests, bench scale flotation experiments were carried out using spodume/quartz and lepodolite/quartz synthetic mixtures. Pure natural samples, further purified in laboratory, and commercial reagents were employed. The minerals were characterized by X-ray diffraction technique. Selectivity between spodume and quartz was achieved through modification with corn starch and between lepidolite and quartz through pH control in the acidic range. (Author) [pt

  6. Recovery of Chromium Ions From Electroplating Wastewater by Flotation, Gamma Irradiation and Adsorption onto Hydrogels

    International Nuclear Information System (INIS)

    Eid, M.; Dessouki, A.M.; Omar, A.M.

    2005-01-01

    At present, the wastewater treatment facilities in many plating plants are approaching their time for replacement. On this occasion there is a strong requirement to re-evaluate the wastewater treatment measures from the point of view of treatment technology. Laboratory investigation was undertaken on the flotation of Cr (VI) from aqueous suspension over whole ph range, aiming at the separation of chromium by flotation. The cationic surfactant (hexadecyl triethyl ammonium bromide) was applied as a collector. Surface properties, in particular the critical micelle concentration, the effectiveness of surface tension reduction, efficiency, surface excess and the minimum surface area were measured at 30 μ C. The electro-flotation was applied with and without the collector at different times for the removal of chromium (VI). The results were discussed in term of surface properties of the collectors at the solution/air interface. Further work took place by irradiating the water samples by gamma- irradiation to reduce the highly toxic Cr(VI) to the much less toxic and less soluble Cr1 in water; therefore, there is a potential for the complete removal of chromium from aqueous solutions. The possibility of using hydrogels for the uptake of irradiated chromium solutions by different hydrogels was investigated. The structure of the hydrogels was estimated by using FT1R and the pore structure of the hydrogels before and after dictating with chromium ions was monitored by SEM. The adsorption studies show that, it is ph dependent. Lowering of the chromium concentration below the maximum permissible value have been achieved after the treatment of chromium solution by flotation, gamma irradiation and adsorption onto hydrogels

  7. Silver recovery from the waste materials by the method of flotation process

    Directory of Open Access Journals (Sweden)

    B. Oleksiak

    2018-01-01

    Full Text Available During the leaching process of zinc concentrates, the waste materials rich in various metals such as eg. silver are produced. So far no attempts of silver recovery from the mentioned waste materials have been made due to the lack of any method which would be both effective and beneficial. The paper presents some possibilities of application of flotation process in silver recovery form waste materials generated during zinc production.

  8. Use of depressants in the direct flotation of a silicate-carbonate phosphate ore

    OpenAIRE

    Souza, Adalberto Leles de; Albuquerque, Rodrigo Oscar de; Lameiras, Fernando Soares; Praes, Plínio Eduardo; Peres, Antônio Eduardo Clark

    2014-01-01

    A high demand for mineral resources observed in recent decades has led to an expansion in production in the mining industry. Different process alternatives have been proposed for selective separation between apatite and contaminants (carbonates and silicates) present in phosphate ores. Magnetic separation, calcination and gravity separation processes are methods that present low efficiency and high cost. Flotation is the most common process; however the selectivity is hampered by the superfic...

  9. Use of coagulants in treatment of olive oil wastewater model solutions by induced air flotation.

    Science.gov (United States)

    Meyssami, B; Kasaeian, A B

    2005-02-01

    Natural polyelectrolytes are suitable coagulants for the treatment of industrial and minicipal wastewaters because they are safe and have environmental benefits. Chitosan, a natural cationic polyelectrolyte, and other similar coagulants were used in the treatment of an olive oil water suspension as a model for the processing wastewater. The effect of chitosan, starch, alum and ferric chloride on the coagulation of oil droplets were determined by the jar test apparatus and turbidometric measurements. Olive oil emulsion samples were prepared by the use of surface active agents and other agents that could form stable oil water emulsions. The effect of parameters such as pH, ionic strength and optimum dosage of the coagulants were determined in the jar test experiments. Following the jar experiments, with the optimum concentration of the suitable coagulant, the emulsions were placed in an induced air flotation (IAF) cell to separate the coagulated oil droplets from solution. In the air flotation experiments, the effect of temperature, surfactant concentration and air flowrate were determined on the decrease of turbidity and COD of the emulsion samples. In the jar experiments, chitosan and alum used together at concentrations of 15 and 25 ppm, respectively, at pH 6 produced the lowest turbidity values. In the air flotation experiments, a concentration of 100 ppm of chitosan, an air flowrate of 3 l/min, aeration time of 45 s, temperature of 20 degrees C and pH 6 produced optimum levels. At optimum conditions of coagulation and flotation stages, the COD of the olive oil emulsion could be reduced by 95%.

  10. Optimizing the air flotation water treatment process. Final report, May 1997

    Energy Technology Data Exchange (ETDEWEB)

    Barnett, B.

    1998-09-01

    The injection water for the Nelson Project is a combination of produced and make-up water, typical of many Eastern Kansas operations. The make-up water is a low-salinity salt water from the Arbuckle Formation and contains dissolved minerals and sulfides. The produced water contains suspended oil, suspended clay and silt particles, along with a combination of other dissolved minerals. The combination of the two waters causes several undesirable reactions. The suspended solids load contained in the combined waters would plug a 75-micron plant bag filter within one day. Wellhead filters of 75-micron size were also being used on the injection wells. The poor water quality resulted in severe loss of injectivity and frequent wellbore cleaning of the injection wells. Various mechanical and graded-bed filtration methods were considered for cleaning the water. These methods were rejected due to the lack of field equipment and service availability. A number of vendors did not even respond to the author`s request. The air flotation process was selected as offering the best hope for a long-term solution. The objective of this work is to: increase the cost effectiveness of the process through optimizing process design factors and operational parameters. A vastly modified air flotation system is the principal tool for accomplishing the project objective. The air flotation unit, as received from manufacturer Separation Specialist, was primarily designed to remove oil from produced water. The additional requirement for solids removal necessitated major physical changes in the unit. Problems encountered with the air flotation unit and specific modifications are detailed in the body of the report.

  11. Influence of some ions on the flotation of apatite from Itataia, in Brazil

    International Nuclear Information System (INIS)

    Aquino, J.A. de.

    1987-01-01

    The influence of ionic composition in the water from Itataia dam in flotation process for phosphate recovery contained in the ore from Itataia reserve CE, in Brazil, is studied. A water treatment system to assure levels of content and recovery obtained during ore dressing stage is defined. Laboratory tests to verify variation of P 2 O 5 recovery in function of different ion concentration were done. (M.C.K.) [pt

  12. Method for the flotation oil extraction of light filth from ground capsicums.

    Science.gov (United States)

    Thrasher, J J; Colliflower, E J

    1977-05-01

    The present official first action method for ground capsicums, 44.123, was adopted in 1945 and there have been great changes in processing and examination of spices since that time. The proposed method involves isopropanol pretreatment, followed by wet sieving and extraction of the light filth from 60% ethanol with flotation oil. The filter papers were clean and recoveries were good (95%) for 5 different lots of capsicums and annato spiked with insect fragments and rodent hairs.

  13. Flotation in column-recovery of fine uranium phosphate ore from Itataia, in Brazil

    International Nuclear Information System (INIS)

    Reis Junior, J.B.; Peres, A.E.C.

    1987-01-01

    A systematic study of main variables of the flotation column and, the study of different pillot circuits integrated by flotation cells in colunm and mechanic cells, aiming at reduction the loss of the sludges for processing uranium phosphate from Itataia, in Brazil, are presented. A recovery of 49% of P 2 O 5 for a content of 24% of P 2 O 5 and 0,185% of U 3 O 8 in the concentrate, using a circuit with two columns, a rougher and scavenger, was obtained. For a content of 33.4% of P 2 O 5 and 0.240% of U 3 O 8 , a recovery of 38% of P 2 O 5 was obtained, using a circuit composed by a mechanical cell as scavenger and two columns as rougher and cleaner. The circuit used to obtain these parameters operated with 7,6 Kg/h solid flow in the grain size range of 10μm and 3μm and the flotation column with 5 cm of diameter and 6m of high. (M.C.K.) [pt

  14. Condutivity effect in electro-coagulation-flotation applied to physico-chemical wastewater treatment

    Directory of Open Access Journals (Sweden)

    Francisco Javier Cuba Terán

    2007-03-01

    Full Text Available This study reports on the effect of conductivity on the simultaneous applicability of water electrolysis , chemical coagulation and flotation fundamentals in the treatment of wastewater with large amounts of suspended matter, characterizing electro-coagulation-flotation (ECF . Results from experiments carried out in a pilot study implanted and operated in the Laboratory of Environment Control (LCA, at the State University of Campinas in Limeira are presented. ECF was developed in an electrolytic reactor where water passed through aluminum electrodes connected to a power supply. Electrochemical reactions promoted Al3+ ions emission from anode, neutralizing repulsive pollutant forces, forming flakes. An evolution of micro hydrogen bubbles occurred, carrying the flakes to the top of the solution, causing flotation and polluter removal. System monitoring aimed at reaching optimal operation conditions regarding time of liquid permanence in the reactor, influence of the NaC1 addition on the increase of affluent conductivity, and influence of polarity inversion over cathodic passivation. Results from carwash wastewater treatment reported 86% efficiency rate for color, 90,15% for turbidity and 85,43% for oil and axle-grease removal.

  15. An Investigation of Reverse Flotation Separation of Sericite from Graphite by Using a Surfactant: MF

    Directory of Open Access Journals (Sweden)

    Yangshuai Qiu

    2016-06-01

    Full Text Available In this paper, a surfactant, atlox4862 (formaldehyde condensate of methyl naphthalene sulfonic sodium salt (MF, was introduced as a depressant for reverse flotation separation of sericite from graphite. Natural flake graphite has a strong hydrophobic property. After interacting with MF, the graphite became moderately hydrophilic. The flotation results showed that MF had a depressing ability for both sericite and graphite and that the flotation separation of sericite from graphite was attributed to the different declining levels of recovery between graphite and sericite with increased MF concentration. For a pulp pH of 8 and a MF concentration of 250 mg/L, the recovery rates of sericite and graphite were 89.7% and 11.3%, respectively. The results of the FTIR spectra and zeta potential measurements demonstrated that the interaction of MF with graphite and sericite is mainly through electrostatic attraction. MF was preferred to adsorb on the surface of graphite, decreasing its zeta potential and improving its hydrophilicity more than that of sericite.

  16. The role of phenols from bagasse vacuum pyrolysis bio-oil in cupper sulfured ore flotation

    Directory of Open Access Journals (Sweden)

    L. E. Brossard

    2008-12-01

    Full Text Available Vacuum pyrolysis bagasse bio-oil collected in a series of sequential fractions was analyzed for total percentage of phenols and levoglucosan components. It was established that the ratio total phenols- to-levoglucosan could be used as an indicator of the performance of alkaline solutions of bio-oil fractions (SABO when they are used as foaming agents to benefit flotation of sulfured cupper minerals. A high total phenol-to-levoglucosan ratio results in high percentages of Cu in cupper flotation concentrates, L Cu. A closer look at the role of individual phenols reveals that p-cresol is the main phenol, although not the only one, responsible for the observed behavior. Additionally it was noted that rather high doses of these foaming agents must be used to obtain desirable results in flotation processes. A production cost estimate allows consideration of SABO as an alternative to others commercial foaming agents, especially if an optimization study reduces doses of SABO.

  17. Flotability and flotation separation of polymer materials modulated by wetting agents.

    Science.gov (United States)

    Wang, Hui; Wang, Chong-qing; Fu, Jian-gang; Gu, Guo-hua

    2014-02-01

    The surface free energy, surface tension and contact angles were performed to investigate the properties of wetting agents. Adsorption of wetting agents changes wetting behavior of polymer resins. Flotability of polymer materials modulated by wetting agents was studied, and wetting agents change significantly flotability of polymer materials. The flotability decreases with increasing the concentration of wetting agents, and the wetting ability is lignin sulfonate (LS)>tannic acid (TA)>methylcellulose (MC)>triton X-100 (TX-100) (from strong to weak). There is significant difference in the flotability between polymer resins and plastics due to the presence of additives in the plastics. Flotation separation of two-component and multicomponent plastics was conducted based on the flotability modulated by wetting agents. The two-component mixtures can be efficiently separated using proper wetting agent through simple flotation flowsheet. The multicomponent plastic mixtures can be separated efficiently through multi-stage flotation using TA and LS as wetting agents, and the purity of separated component was above 94%, and the recovery was more than 93%. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Surface modification of malachite with ethanediamine and its effect on sulfidization flotation

    Science.gov (United States)

    Feng, Qicheng; Zhao, Wenjuan; Wen, Shuming

    2018-04-01

    Ethanediamine was used to modify the mineral surface of malachite to improve its sulfidization and flotation behavior. The activation mechanism was investigated by adsorption experiments, X-ray photoelectron spectroscopy (XPS) analysis, and zeta potential measurements. Microflotation experiments showed that the flotation recovery of malachite was enhanced after the pretreatment of the mineral particles with ethanediamine prior to the addition of Na2S. Adsorption tests revealed that numerous sulfide ion species in the pulp solution were transferred onto the mineral surface through the formation of more copper sulfide species. This finding was confirmed by the results of the XPS measurements. Ethanediamine modification not only increased the contents of copper sulfide species on the malachite surface but also enhanced the reactivity of the sulfidization products. During sulfidization, Cu(II) species on the mineral surface were reduced into Cu(I) species, and the percentages of S22- and Sn2- relative to the total S increased after modification, resulting in increased surface hydrophobicity. The results of zeta potential measurements showed that the ethanediamine-modified mineral surface adsorbed with more sulfide ion species was advantageous to the attachment of xanthate species, thereby improving malachite floatability. The proposed ethanediamine modification followed by sulfidization xanthate flotation exhibits potential for industrial application.

  19. Effect of using dissolved air flotation system on industrial wastewater treatment in pilot scale

    International Nuclear Information System (INIS)

    Yahya, Habibzadeh

    2010-01-01

    In the present paper the application of Dissolved Air Flotation (DAF) system for wastewater treatment, especially for industrial wastewater on a designed pilot system has been investigated. It is for the first time in dissolved air flotation system that instead of air dissolving tube, hydro cyclone technology is used to dissolve air in water with ratio of 1:1 (almost 100 percent) in the form of small air bubbles and a circular flotation tank instead of rectangular tank. The advantage of usage of circular tank in DAF system is the capability of being treated in higher rate of mass, so less space is needed. Although application of hydro cyclone with different diameters of holes for producing mixing energy which also has the capability of direct injection of chemical coagulant and polymeric materials leads to the higher efficiency of treatment and so reduces the cost of pump and consumed air. Investigations on the efficiency of this system was done by providing and analyzing samples of wastewater with and without adding of PAC (Poly-Aluminium-Chloride). Sampling and analyzing was done according to standard methods. The results of the analyses show that pilot system has high efficiency, especially for oil removal

  20. Bioleaching of copper from old flotation tailings samples (Copper Mine Bor, Serbia

    Directory of Open Access Journals (Sweden)

    Stanković Srđan

    2015-01-01

    Full Text Available Bioleaching of samples taken from depths of 10, 15, and 20 meters from old flotation tailings of the Copper Mine Bor was conducted in shaken flasks using extremely acidic water of Lake Robuleas lixiviant. Yield of copper after five weeks of the bioleaching experiment was 68.34±1.21% for 15 m sample, 72.57±0.57% for 20 m sample and 97.78±5.50% for 10 m sample. The obtained results were compared to the results of acid leaching of the same samples and it was concluded that bioleaching was generally more efficient for the treatment of samples taken from depths of 10 m and 20 m. The content of pyrite in the 20 m sample, which contained the highest amount of this mineral, was reduced after bioleaching. Benefits of this approach are: recovery of substantial amounts of copper, reducing the environmental impact of flotation tailings and the application of abundant and free water from the Robule acidic lake as lixiviant. Results of the experiment showed that bioleaching can be more efficient than acid leaching for copper extraction from flotation tailings with higher sulfide contents. [Projekat Ministarstva nauke Republike Srbije, br. 176016 i br. 173048

  1. Separation of oily materials in radioactive waste waters by flotation. Determination of operation and control parameters

    International Nuclear Information System (INIS)

    Ortiz O, H.B.; Flores E, R.M.

    2003-01-01

    In this work the determination of the operation and control parameters (air/solids ratio G/S, retention time Θ, pressure P and de pressurized volume of mixed air-water V), of the flotation system used in the treatment of oleaginous residual water (polluted mainly with 60 Co) coming from the decontamination process of worn out oils, using as response parameters the concentration of oleaginous material and the residual turbidity. The obtained results allowed to observe the dependence of G/S with the pressure and volume of air-water given. At the same time it was settled down that the set of operation conditions that offers the greater separation percentage of G As and turbidity in the smallest time, they are those obtained by V 2 = 0.0012 m 3 and P 2 = 620 kPa, (G/S = 0.30 - 0.35, = 14-16 min) for what were employees as the ideal values of operation and control in the flotation system. As long as, the concentration of total Co is found under 1 mgL -1 . Finally, the selected flotation system showed high separation levels of 60 Co, whose specific activity are below of 0.007 BqmL -1 . (Author)

  2. Synthesis of Novel Ether Thionocarbamates and Study on Their Flotation Performance for Chalcopyrite

    Directory of Open Access Journals (Sweden)

    Gang Zhao

    2016-09-01

    Full Text Available Novel ether thionocarbamates, O-butoxy isopropyl-N-ethoxycarbonyl thionocarbamate (BIPECTC and O-(2-butoxy-1-methylethoxy isopropyl-N-ethoxycarbonyl thionocarbamate (BMIPECTC, were synthesized in this study. Their collecting efficiencies in the flotation of chalcopyrite were investigated using flotation tests, adsorption measurements, ultraviolet spectra (UV and Fourier transform-infrared spectroscopy (FT-IR and density functional theory (DFT calculations. The synthesized ether thionocarbamates showed better frothing properties than methyl-isobutyl-carbinol (MIBC and stronger affinity to chalcopyrite compared with O-isopropyl-N-ethyl thionocarbamate (IPETC and O-isobutyl-N-ethoxycarbonyl thionocarbamate (IBECTC. UV spectra analysis showed that the ether thionocarbamates react with Cu2+, with the exception of Fe2+, Ni2+, Zn2+ and Pb2+. Additionally, it was further confirmed by FTIR spectra that a chemical reaction occurs between copper ion and BIPECTC and BMIPECTC. The adsorption capacity measurements revealed that chalcopyrite exhibits good adsorption ability for ether thionocarbamates at an approximate pH of 8–10, which agrees with the flotation tests. The quantum chemistry calculation results indicated that the ether thionocarbamates exhibit stronger collecting ability for copper mineral in terms of frontier molecular orbital analysis, binding model simulation with copper ions and the molecular hydrophobicity compared with IPETC and IBECTC. The computational results are in very good agreement with the experimental results.

  3. Waster water treatment with Cavitation Air Flotation (CAF) system; Tratamiento de las aguas residuales utilizando el sistema de flotacion por aire inducido (CAF)

    Energy Technology Data Exchange (ETDEWEB)

    Escofet Lugstenmann, I.

    1998-12-01

    In wastewater treatment from industries, the flotation process as physical-chemical treatment or primary treatment, based on the difference of densities of the solid-liquid suspension, is an important step for the elimination of the contaminant material, both as suspended solids and oils and greases. The Cavitation Air Flotation (CAF) system is an unique, innovative and very easy method which introduces air into the flotation system. It was created to come over the problems and limitations of more conventional techniques of Dissolved Air Flotation (DAF). (Author) 9 refs.

  4. Synergistic Adsorption and Flotation of New Mixed Cationic/Nonionic Collectors on Muscovite

    Directory of Open Access Journals (Sweden)

    Hao Jiang

    2017-05-01

    Full Text Available The mixed cationic collector cetyltrimethylammonium chloride (CTAC and nonionic collector octanol (OCT was found to exhibit a synergistic effect on the flotation and adsorption of muscovite. To understand the underlying synergistic mechanism, flotation, contact angle, surface tension, and adsorption measurements were carried out. The results obtained from flotation measurements indicated that the mixed CTAC/OCT exhibits a better collecting ability than CTAC or OCT. The recovery of muscovite with CTAC only rapidly decreased from 97.25% at pH 2.64 to 75.26% at pH 5.82, followed by a flat horizontal at a pH is higher than 6. In contrast, a high recovery of greater than 85% muscovite was observed using mixed CTAC/OCT at α CTAC = 0.67 (the mole ratio of CTAC:OCT = 2:1 over the investigated pH range. From the surface activity parameters (CMC, γ CMC, Γmax, Amin estimated from surface measurements and interaction parameters (βm, βσ, in addition to the micellar and interfacial compositions ( x 1 m , x 1 σ obtained from the theory of regular solutions, a synergistic effect is evident in the mixed micelle and at the water/air interface. Moreover, the mixed CTAC/OCT at α CTAC = 0.67 exhibited the maximum synergistic interaction. The results obtained from surface tension measurements indicated that the mixed CTAC/OCT exhibits considerably higher surface activities compared to single CTAC or OCT. The contact angle results confirmed that the mixed CTAC/OCT is a better collector than the individual CTAC or OCT for the flotation of muscovite. According to the results obtained from adsorption experiments, compared with that of individual CTAC or OCT, the amounts of CTAC and OCT adsorbed on the muscovite surface are considerably increase in the mixed systems because of co-adsorption. Based on these results, the mixed CTAC/OCT exhibits a remarkable synergistic effect during the flotation and adsorption of muscovite.

  5. Clarification of Muscat musts using wheat proteins and the flotation technique.

    Science.gov (United States)

    Marchal, Richard; Lallement, Armelle; Jeandet, Philippe; Establet, Gérard

    2003-03-26

    The bovine spongiform encephalopathy (BSE, mad cow) crisis has led some wine-makers to question gelatin as a fining agent and to reject the use of these animal proteins. The search for a substitute for gelatin was begun by comparing vegetable proteins (particularly gluten) with gelatin fining treatments. Clairette de Die (French-controlled appellation) is a sparkling sweet wine. The alcoholic fermentation begins in a tank, continues in a crown-cap bottle, and stops before the complete consumption of sugar. All particles present in the bottle have to be removed before corking, and it is important to have a must as clear as possible. This study concerned the clarifying of a Muscat must, treated with pectinases, using a very efficient flotation technique. The must is fined with bentonite/silica/protein (fish gelatin, wheat gluten, or lupin isolate) to induce flocculation and then pressurized (6 bar). After depressurization, microbubbles cling to flocculates and climb to the top of the flotation tank (this flotation foam is clarified using a rotary filter). At laboratory scale, gluten (20 g/hL) and gelatin (10 g/hL) (each combined with bentonite and silica gel) gave turbidities of 50 and 35 NTU, respectively (6.5 and 4.1% of that of the nontreated must). The Muscat must was also clarified by static settling. The turbidity decreased by 86% for the gluten/bentonite fining and by 60% for the gelatin/bentonite fining. Visually, gluten flocculation takes longer to occur and flocculates sedimentation is longer than with gelati, but the removal of insoluble particles is more complete and leads to lower turbidities. At an industrial scale, gluten (20 g/hL) and gelatin (10 g/hL) (each combined with bentonite and silica gel) gave turbidities of 60 and 48 NTU, respectively. Turbidities measured in the tanks 14 h after the flotation showed a better efficiency for the wheat gluten (24 NTU) compared to gelatin (28 NTU). This is explained by the static settling that completed the

  6. Polyethoxylated carboxylic surfactant for ion foam flotation: fundamental study from solution to foam

    International Nuclear Information System (INIS)

    Micheau, Cyril

    2013-01-01

    Ion foam flotation allows to concentrate ions in a foam phase formed by a soap. For classical systems, the strong interaction between ions and surfactant generally leads to the formation of precipitates and of froth. When the froth collapses, the solid residue thus recovered requires a recycling or conversion. In order to remedy this, the present work uses as collector a polyethoxylated carboxylic surfactant, AKYPO RO 90 VG, which forms soluble ion/surfactant complexes, even with multi-charge ions. This work presents a detailed study of the fundamental mechanisms that govern the extraction of ions by foaming. In the first part, surface activity and acid/base properties of the surfactant in solution are determined by combining numerous independent techniques which are pH-metric dosage, tensiometry and small angle scattering. The evolution of these properties in the presence of different nitrate salts (Nd, Eu, Ca, Sr, Cu, Li, Na, Cs) coupled with electrophoretic measurements give a first approach to selectivity. Finally, all of these data combined with a study of the formation of surfactant/ion complexes allow us to determine the speciation of Nd/AKYPO system as a function of pH. In the second part, the analysis of the foam by conductivity and neutron scattering provides information on the wetness and foam film thickness, parameters governing foam stability. The pH and the nature of the added ions, their number of charge and also their chemical nature thus appear to be major parameters that governed wetness and foam film thickness. The last part is devoted to the understanding of the ion extraction/separation experiments by flotation based on all previous results. It is shown that the flotation of neodymium is strongly related to its speciation, which could lead to its re-extraction or its flotation in precipitated form. It is shown that, neodymium induces a phenomenon of mono-charge ion depletion in the foam. This ionic specificity allows to consider the studied

  7. Numerical Simulations of Two-Phase Flow in a Self-Aerated Flotation Machine and Kinetics Modeling

    KAUST Repository

    Fayed, Hassan E.

    2015-03-30

    A new boundary condition treatment has been devised for two-phase flow numerical simulations in a self-aerated minerals flotation machine and applied to a Wemco 0.8 m3 pilot cell. Airflow rate is not specified a priori but is predicted by the simulations as well as power consumption. Time-dependent simulations of two-phase flow in flotation machines are essential to understanding flow behavior and physics in self-aerated machines such as the Wemco machines. In this paper, simulations have been conducted for three different uniform bubble sizes (db = 0.5, 0.7 and 1.0 mm) to study the effects of bubble size on air holdup and hydrodynamics in Wemco pilot cells. Moreover, a computational fluid dynamics (CFD)-based flotation model has been developed to predict the pulp recovery rate of minerals from a flotation cell for different bubble sizes, different particle sizes and particle size distribution. The model uses a first-order rate equation, where models for probabilities of collision, adhesion and stabilization and collisions frequency estimated by Zaitchik-2010 model are used for the calculation of rate constant. Spatial distributions of dissipation rate and air volume fraction (also called void fraction) determined by the two-phase simulations are the input for the flotation kinetics model. The average pulp recovery rate has been calculated locally for different uniform bubble and particle diameters. The CFD-based flotation kinetics model is also used to predict pulp recovery rate in the presence of particle size distribution. Particle number density pdf and the data generated for single particle size are used to compute the recovery rate for a specific mean particle diameter. Our computational model gives a figure of merit for the recovery rate of a flotation machine, and as such can be used to assess incremental design improvements as well as design of new machines.

  8. Accuracy of egg flotation throughout incubation to determine embryo age and incubation day in water bird nests

    Science.gov (United States)

    Ackerman, Joshua T.; Eagles-Smith, Collin A.

    2010-01-01

    Floating bird eggs to estimate their age is a widely used technique, but few studies have examined its accuracy throughout incubation. We assessed egg flotation for estimating hatch date, day of incubation, and the embryo's developmental age in eggs of the American Avocet (Recurvirostra americana), Black-necked Stilt (Himantopus mexicanus), and Forster's Tern (Sterna forsteri). Predicted hatch dates based on egg flotation during our first visit to a nest were highly correlated with actual hatch dates (r = 0.99) and accurate within 2.3 ?? 1.7 (SD) days. Age estimates based on flotation were correlated with both day of incubation (r = 0.96) and the embryo's developmental age (r = 0.86) and accurate within 1.3 ?? 1.6 days and 1.9 ?? 1.6 days, respectively. However, the technique's accuracy varied substantially throughout incubation. Flotation overestimated the embryo's developmental age between 3 and 9 days, underestimated age between 12 and 21 days, and was most accurate between 0 and 3 days and 9 and 12 days. Age estimates based on egg flotation were generally accurate within 3 days until day 15 but later in incubation were biased progressively lower. Egg flotation was inaccurate and overestimated embryo age in abandoned nests (mean error: 7.5 ?? 6.0 days). The embryo's developmental age and day of incubation were highly correlated (r = 0.94), differed by 2.1 ?? 1.6 days, and resulted in similar assessments of the egg-flotation technique. Floating every egg in the clutch and refloating eggs at subsequent visits to a nest can refine age estimates. ?? The Cooper Ornithological Society 2010.

  9. Quantification of Campylobacter spp. in chicken rinse samples by using flotation prior to real-time PCR.

    Science.gov (United States)

    Wolffs, Petra; Norling, Börje; Hoorfar, Jeffrey; Griffiths, Mansel; Rådström, Peter

    2005-10-01

    Real-time PCR is fast, sensitive, specific, and can deliver quantitative data; however, two disadvantages are that this technology is sensitive to inhibition by food and that it does not distinguish between DNA originating from viable, viable nonculturable (VNC), and dead cells. For this reason, real-time PCR has been combined with a novel discontinuous buoyant density gradient method, called flotation, in order to allow detection of only viable and VNC cells of thermotolerant campylobacters in chicken rinse samples. Studying the buoyant densities of different Campylobacter spp. showed that densities changed at different time points during growth; however, all varied between 1.065 and 1.109 g/ml. These data were then used to develop a flotation assay. Results showed that after flotation and real-time PCR, cell concentrations as low as 8.6 x 10(2) CFU/ml could be detected without culture enrichment and amounts as low as 2.6 x 10(3) CFU/ml could be quantified. Furthermore, subjecting viable cells and dead cells to flotation showed that viable cells were recovered after flotation treatment but that dead cells and/or their DNA was not detected. Also, when samples containing VNC cells mixed with dead cells were treated with flotation after storage at 4 or 20 degrees C for 21 days, a similar percentage resembling the VNC cell fraction was detected using real-time PCR and 5-cyano-2,3-ditolyl tetrazolium chloride-4',6'-diamidino-2-phenylindole staining (20% +/- 9% and 23% +/- 4%, respectively, at 4 degrees C; 11% +/- 4% and 10% +/- 2%, respectively, at 20 degrees C). This indicated that viable and VNC Campylobacter cells could be positively selected and quantified using the flotation method.

  10. Personal Flotation Devices Research. Volume 2. Research Report.

    Science.gov (United States)

    1978-01-01

    ESTIMA’~ED PERCENTAGE OF ADULT RECREAT IONAL SOA T ISO ~CCTrEN T V1CTi ~ S ANNIJAL LY 0.4 - 14.0 1.1 - 7 7 78.3 - 98.5...of PFDs which interview subjects reportedly keep accessible on a norma l outing. It should be emphasized that the interview data are all self-reports...of random variables. According to the central limit theorem , the distribution of Fw and FA scores for a specified PFD should approach a norma l

  11. Flotation removal of the microalga Nannochloropsis sp. using Moringa protein-oil emulsion: A novel green approach.

    Science.gov (United States)

    Kandasamy, Ganesan; Shaleh, Sitti Raehanah Muhamad

    2018-01-01

    A new approach to recover microalgae from aqueous medium using a bio-flotation method is reported. The method involves utilizing a Moringa protein extract - oil emulsion (MPOE) for flotation removal of Nannochloropsis sp. The effect of various factors has been assessed using this method, including operating parameters such as pH, MPOE dose, algae concentration and mixing time. A maximum flotation efficiency of 86.5% was achieved without changing the pH condition of algal medium. Moreover, zeta potential analysis showed a marked difference in the zeta potential values when increase the MPOE dose concentration. An optimum condition of MPOE dosage of 50ml/L, pH 8, mixing time 4min, and a flotation efficiency of greater than 86% was accomplished. The morphology of algal flocs produced by protein-oil emulsion flocculant were characterized by microscopy. This flotation method is not only simple, but also an efficient method for harvesting microalgae from culture medium. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Treatment of produced water: is a flotation viable process?; Tratamento da agua produzida: a flotacao e um processo viavel?

    Energy Technology Data Exchange (ETDEWEB)

    Santana, Claudia Ramos; Freitas, Andrea Goncalves Bueno de; Silva, Gabriel Francisco da; Paixao, Ana Eleonora Almeida [Universidade Federal de Sergipe (UFS), Aracaju, SE (Brazil); Oliveira, Rosivania da Paixao Silva [Fundacao de Apoio a Pesquisa e Extensao de Sergipe (FAPESE), Aracaju, SE (Brazil)

    2008-07-01

    In petroleum oil wells there comes a situation when most of the oil drilled accompanies a large amount of water. This may be due to the proper conditions of the reservoir or as a consequence of the water injection in the secondary recovery processes from the well. The amount of produced water together with oil can vary to a great extent and it frequently attains to about 50% of the drilled oil. One technique employed for the treatment of industrial effluents, mainly the oily ones which is of great interest is that of flotation. This phenomenon is being extensively used for oil removal from emulsified oils in various areas, such as that of dissolved air flotation (DAF) and the induced air flotation (IAF). The conventional flotation processes consist of the following stages: bubble gas generation (normally air) from the interior of the effluent; collision between the gas bubbles and the suspended oil drops in the water; adhesion of the gas bubbles in the oil drops and ascension of aggregate oil drops/bubbles until the surface, where the oil is removed. This work seeks to contribute for the understanding of the factors which contribute for the selection of the flotation process as one of the methods most viable for the treatment of the produced water. (author)

  13. systematic investigations of foam separation of Nickel (l l) from dilute aqueous solutions; separation by adsorbing colloid flotation

    International Nuclear Information System (INIS)

    Beheir, Sh.G.; Shakir, K.; Aziz, M.

    2004-01-01

    in the preceding parts we dealt with the application of the foam separation processes: ion and precipitate flotations for the separation of Ni (l l) from dilute aqueous solutions. Adsorbing colloid flotation (ACF), another type that has proved very useful, is the subject of this paper. ACF of Ni(l l) was investigated using Al (OH) 3 as a colloidal carrier, cetyl trimethyl ammonium bromide (CTAB) or sodium lauryl sulphate (NaLs) either singly or in combination with gelatin as collectors. the precipitate flotation curve obtained for the carrier Al(OH) 3 , was compared with the corresponding theoretical one calculated from the data published for Al(I I I) hydrolysis. the effects of the different parameters that can influence the flotation process were determined . removals approaching 100% could be achieved under the optimum conditions. the results obtained were discussed with respect to the chemical state of Ni (l l), the ionization behaviour of the collectors, and properties of the carrier precipitate , and are compared with those results obtained by the ion and precipitate flotation techniques. the developed ACF process was successfully applied to the removal of Ni (l l) from radioactive wastewater

  14. A novel process for separation of hazardous poly(vinyl chloride) from mixed plastic wastes by froth flotation.

    Science.gov (United States)

    Wang, Jianchao; Wang, Hui; Wang, Chongqing; Zhang, Lingling; Wang, Tao; Zheng, Long

    2017-11-01

    A novel method, calcium hypochlorite (CHC) treatment, was proposed for separation of hazardous poly(vinyl chloride) (PVC) plastic from mixed plastic wastes (MPWs) by froth flotation. Flotation behavior of single plastic indicates that PVC can be separated from poly(ethylene terephthalate) (PET), poly(acrylonitrile-co-butadiene-co-styrene) (ABS), polystyrene (PS), polycarbonate (PC) and poly(methyl methacrylate) (PMMA) by froth flotation combined with CHC treatment. Mechanism of CHC treatment was examined by contact angle measurement, scanning electron microscopy, Fourier transform infrared and X-ray photoelectron spectroscopy. Under the optimum conditions, separation of PVC from binary plastics with different particle sizes is achieved efficiently. The purity of PC, ABS, PMMA, PS and PET is greater than 96.8%, 98.5%, 98.8%, 97.4% and 96.3%, respectively. Separation of PVC from multi-plastics was further conducted by two-stage flotation. PVC can be separated efficiently from MPWs with residue content of 0.37%. Additionally, reusing CHC solution is practical. This work indicates that separation of hazardous PVC from MPWs is effective by froth flotation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Effects of Flotation-Restricted Environmental Stimulation Technique on Stress-Related Muscle Pain: What Makes the Difference in Therapy - Attention-Placebo or the Relaxation Response?

    Directory of Open Access Journals (Sweden)

    Sven A Bood

    2005-01-01

    Full Text Available INTRODUCTION: The purpose of the present study was to examine the potential effects of attention-placebo on flotation tank therapy. Flotation-restricted environmental stimulation technique is a method whereby an individual lies in a floating tank and all stimuli are reduced to a minimum.

  16. Flotation of Toxocara canis Eggs in Commercial Bleach and Effects of Bleach Treatment Times on Larval Development in These Eggs.

    Science.gov (United States)

    von Dohlen, Alexa Rosypal; Houk-Miles, Alice E; Zajac, Anne M; Lindsay, David S

    2017-04-01

    Toxocara canis is a common intestinal nematode of young dogs. Puppies contaminate the environment with large numbers of eggs that can embryonate and become infective in less than a month. Embryonated eggs are infectious for humans and other paratenic hosts. Most T. canis infections in humans are asymptomatic; however, migration of T. canis larvae in the eye and in the central nervous system can result in vision loss, blindness, and even death. The eggs of T. canis are highly resistant to harsh environmental conditions and routinely used chemical disinfectants. The objective of this study was to evaluate the effects of full-strength commercial bleach (5.25% sodium hypochlorite solution) treatment on development of T. canis eggs and to report our serendipitous finding that T. canis eggs in dog feces can float in passive fecal flotation tests using bleach. We also demonstrated that T. canis eggs could be identified using the McMaster's fecal eggs counting test using 100% bleach. Toxocara canis eggs collected from the feces of naturally infected 4-8 wk old puppies were treated with full-strength bleach (5.25% sodium hypochlorite solution) for 15 min, 30 min, 60 min, and 120 min; washed free of bleach smell by centrifugation; and resuspended in 0.1 N sulfuric acid solution to undergo larval development at room temperature for 18 days after exposure to bleach. Motile larvae were observed in T. canis eggs in all groups treated for 15-120 min and eggs continuously exposed to bleach for 18 days. Our results indicate that bleach may not be an appropriate disinfectant for dog kennels, cages, or laboratory utensils and work surfaces. Toxocara canis eggs are resistant to bleach treatment and continue to pose a risk for canine and human infections. Further study is needed to find the most appropriate methods for disinfection and removal of eggs to reduce the risk of transmission of this parasite.

  17. The increase of efficiency of pine oil by heating and usage in the flotation of oxidized Amasra coal

    Energy Technology Data Exchange (ETDEWEB)

    Karsilayan, H.; Afsar, H.; Yilmaz, N.; Yanic, C. (Yildiz University, Istanbul (Turkey). Dept. of Chemistry)

    1992-01-01

    The effect of heating temperature and time on the efficiency of pine oil was examined in the flotation of oxidized Amasra coal in this work. Samples were taken from waste heap Amasra coal which were collected in 1973-1978 and stored in atmospheric conditions. The optimized impeller speed was 1000 rpm, aeration rate was 35 ml/s and solid content of the pulp was 20% in the flotation tests. Motorin was added to the pulp as a collector. The pine oil was heated to 50, 75, 100, 125, 150, 175, 200{degree}C and used as a frother. The flotation results indicated that 125{degree}C was a suitable temperature for heating. Increasing the heating time increased the efficiency of pine oil. The recovery of combustibles also increased depending on the increase in the amount of oil heated for 5 hours at 125{degree}C. 11 refs., 3 figs., 5 tabs.

  18. Advanced treatment of oilfield production wastewater by an integration of coagulation/flotation, catalytic ozonation and biological processes.

    Science.gov (United States)

    Chen, Ke-Yong; Zhang, Xiao-Bing; Li, Jun

    2016-10-01

    In this study, advanced treatment of heavily polluted oilfield production wastewater (OPW) was investigated employing the combination of coagulation/dissolved air flotation, heterogeneous catalytic ozonation and sequencing batch reactor (SBR) processes. Two SBR reactors were separately set up before and after the ozonation unit. The results show that microbubble flotation was more efficient than macrobubble flotation in pollutant removal. Catalytic ozonation with the prepared Fe/activated carbon catalyst significantly enhanced pollutant removal in the second SBR by improving wastewater biodegradability and reducing wastewater microtoxicity. The treatment technique decreased oil, chemical oxygen demand and NH3-N by about 97%, 88% and 91%, respectively, allowing the discharge limits to be met. Therefore, the integrated process with efficient, economical and sustainable advantages was suitable for advanced treatment of real OPW.

  19. ETAAS determination of thallium and silver from water matrix after colloidal precipitate flotation using lead(II hexamethylenedithiocarbamate

    Directory of Open Access Journals (Sweden)

    TRAJCE STAFILOV

    2001-10-01

    Full Text Available Afast method for the preconcentration of thallium and silver in nanogram quantities in fresh drinking waters (source, well, tap and waters for irrigation using colloidal precipitate flotation is described. Lead(II hexamethylenedithiocarbamate, Pb(HMDTC2 played the role of flotation collector. The experimental conditions for the successful separation of thallium and silver (mass of Pb, amount ofHMDTC-, pHof the system, induction time, type of surfactant etc. were optimized. After flotation separation from the mother liquor, the solid sublate containing traces of thallium and silver was dissolved and the analytes were determined by electrothermal atomic absorption spectrometry (ETAAS. The results of the ETAAS analysis are compared with those obtained by inductively coupled plasma-atomic emission spectrometry. The detection limit for thallium by this method is 0.027 mg/l, and for silver 0.005 microg/l.

  20. Culture-independent qunatification of Salmonella enterica in carcass gauze swabs by flotation prior to real-time PCR

    DEFF Research Database (Denmark)

    Löfström, Charlotta; Schelin, Jenny; Norling, Börje

    2010-01-01

    To facilitate quantitative risk assessment in the meat production chain, there is a need for culture-independent quantification methods. The aim of this study was to evaluate the use of flotation, a non-destructive sample preparation method based on traditional buoyant density centrifugation......, for culture-independent quantification of intact Salmonella in pig carcass gauze swabs (100 cm2) prior to quantitative PCR (qPCR). A novel approach was investigated, excluding the homogenization step prior to flotation, to improve the detection limit and speed up the quantification procedure. The buoyant...... density of two Salmonella strains in different growth conditions was determined to be 1.065 – 1.092 g/ml. Based on these data, an optimal discontinuous flotation with three different density layers, ~1.200, 1.102 and 1.055 g/ml, was designed for extracting intact Salmonella cells from pig carcass swabs...

  1. Culture-independent quantification of Salmonella enterica in carcass gauze swabs by flotation prior to real-time PCR

    DEFF Research Database (Denmark)

    Löfström, Charlotta; Schelin, Jenny; Norling, Börje

    2011-01-01

    To facilitate quantitative risk assessment in the meat production chain, there is a need for culture-independent quantification methods. The aim of this study was to evaluate the use of flotation, a non-destructive sample preparation method based on traditional buoyant density centrifugation......, for culture-independent quantification of intact Salmonella in pig carcass gauze swabs (100 cm2) prior to quantitative PCR (qPCR). A novel approach was investigated, excluding the homogenization step prior to flotation, to improve the detection limit and speed up the quantification procedure. The buoyant...... density of two Salmonella strains in different growth conditions was determined to be 1.065 – 1.092 g/ml. Based on these data, an optimal discontinuous flotation with three different density layers, 1.200, 1.102 and 1.055 g/ml, was designed for extracting intact Salmonella cells from pig carcass swabs...

  2. Flotation techniques (FLOTAC and mini-FLOTAC for detecting gastrointestinal parasites in howler monkeys

    Directory of Open Access Journals (Sweden)

    Mayra Alejandra Alvarado-Villalobos

    2017-11-01

    Full Text Available Abstract Background Analyses of environmental correlates of the composition of gastrointestinal parasite communities in black howler monkeys (Alouatta pigra have been hindered by inadequate calibration techniques of detection and quantification methods of the parasites. Here we calibrate samples and compare the likelihood of parasite detection using two flotation techniques, FLOTAC and Mini-FLOTAC, and compare flotation solution, preservation method and dilution ratio for egg detection and counts of the most common parasites (Controrchis spp. and Trypanoxyuris spp. in howler monkeys. Results For samples preserved in 5% formalin, the Mini-FLOTAC technique was the best option for qualitative and quantitative copro-microscopic analysis. This technique displays an 83.3% and 100% detection of Controrchis spp. and Trypanoxyuris spp. infections, respectively. For the trematode Controrchis spp., more eggs per gram of feces (EPG were recorded with the flotation solution (FS #7 (zinc sulfate; specific gravity SG = 1.35 at 1:20 and 1:25 dilution than other methods. By contrast, for the nematode Trypanoxyuris spp., the best results were recorded with FS1 (sucrose and formaldehyde; SG = 1.20 at 1:10 dilution. Conclusions We recommend the Mini-FLOTAC technique for general use with parasite analysis on frugivore/folivores like the howler monkey, especially if many samples are analyzed. The technique has a high detection rate and the best EPG counts, allowing the qualitative and quantitative analysis of parasite load among the species or populations without the need for specialized equipment.

  3. Evaluation of Sulfonate-Based Collectors with Different Hydrophobic Tails for Flotation of Fluorite

    Directory of Open Access Journals (Sweden)

    Renji Zheng

    2018-02-01

    Full Text Available This investigation aims to demonstrate the effects of hydrophobic tails on the affinity and relevant flotation response of sulfonate-based collectors for fluorite. For this purpose, a series of alkyl sulfonates with different hydrophobic tails, namely sodium decanesulfonate (C10, sodium dodecylsulfate (C12, sodium hexadecanesulfonate (C16, and sodium dodecylbenzenesulfonate (C12B were applied. The flotation tests showed that C12 and C12B had a better collecting performance than C10 and C16 at pH < 10, and the flotation recovery of fluorite was higher when adopting C12B as a collector compared with C12 with a strong base. The adsorption behaviors of collectors on the fluorite surface were studied through zeta potential, Fourier transform infrared (FTIR, and X-ray photoelectron spectroscopy (XPS analyses. It was found that the affinity of alkyl sulfonates for fluorite was enhanced with the increase of the alkyl chain length from C10 to C16. The existence of phenyl in the hydrophobic tail of sulfonates could improve its activity for fluorite by reducing its surface tension. The abnormal phenomenon C16 with a high affinity for fluorite had a low collecting performance for fluorite mainly due to its overlong alkyl chain, resulting in low solubility in pulp, which restrained its interaction with fluorite. We concluded that C12B was the most applicable collector for fluorite among these reagents due to its high activity, high solubility, and low cost, which was further substantiated by calculating their molecular frontier orbital energy.

  4. Air-Sparged Hydrocyclone/Advanced Froth Flotation fine coal cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Stoessner, R.D. (Pennsylvania Electric Co., Johnstown, PA (USA)); Shirey, G.A.; Zawadzki, E.A. (Management and Technical Systems, McMurray, PA (USA)); Welsh, C.F. (Davy Dravo (USA)); Miller, J.D. (Utah Univ., Salt Lake City, UT (USA)); Shell, W.P. (Ebasco Services, Inc., New York, NY (USA))

    1990-05-27

    In May 1988, the Pennsylvania Electric Company (Penelec) and New York State Electric and Gas Corporation (NYSEG) were awarded a contract from the Department of Energy's Pittsburgh Energy and Technology Center (DOE-PETC) to evaluate the performance of a two-inch Air-Sparged Hydrocyclone (ASH) for cleaning fine minus-100-mesh coal. A 24-month study was successfully completed, optimizing the performance of the ASH for cleaning raw classified, naturally-occurring minus-100-mesh Upper Freeport coal, and comparing its performance with Advanced Froth Flotation (AFF), a procedure utilizing conventional flotation equipment operated in an advanced manner (low impeller speeds, starvation float, multiple-stage cleaning, etc.) with highly selective reagents to optimize ash and pyritic sulfur rejection. The economics of cleaning fine coal by both processes at commercial scale, for retrofit and greenfield applications were found to be comparable within the accuracy of the study. Technical performance of the two processes were also found to be essentially identical. Thus, the ASH would be the best choice for a retrofit installation into an existing plant because of requiring less space. Both processes were successful in achieving excellent separations when cleaning the Upper Freeport coal. Both the ASH and AFF circuits were able to produce a clean-coal product of yield (65--80 percent weight recovery) and quality (5--6 percent ash) equivalent to that as theoretically determined by float-sink washability analyses. Combining either of the two fine coal flotation processes with a classifying cyclone circuit resulted in pyritic sulfur rejection values of about 85 percent. 47 refs., 109 figs., 75 tabs.

  5. A comparative study of turbulence models for dissolved air flotation flow analysis

    Energy Technology Data Exchange (ETDEWEB)

    Park, Min A; Lee, Kyun Ho; Chung, Jae Dong [School of Mechanical and Aerospace Engineering, Sejong University, Seoul (Korea, Republic of); Seo, Seung Ho [Tops Engineering Co, Ltd., Gwangmyeong (Korea, Republic of)

    2015-07-15

    The dissolved air flotation (DAF) system is a water treatment process that removes contaminants by attaching micro bubbles to them, causing them to float to the water surface. In the present study, two-phase flow of air-water mixture is simulated to investigate changes in the internal flow analysis of DAF systems caused by using different turbulence models. Internal micro bubble distribution, velocity, and computation time are compared between several turbulence models for a given DAF geometry and condition. As a result, it is observed that the standard κ-ε model, which has been frequently used in previous research, predicts somewhat different behavior than other turbulence models.

  6. Evaluating the efficacy of a centrifugation-flotation method for extracting Ascaris ova from soil

    DEFF Research Database (Denmark)

    Cranston, Imogen; Teoh, Penelope J.; baker, Sarah M.

    2016-01-01

    method to extract STH ova from soil makes it challenging to examine whether the use of latrines may or may not have an effect on environmental contamination with ova. The present study evaluated the recovery rate of a method developed to extract STH ova from soil. Methods: The adapted centrifugation...... with increasing soil moisture content, particle size and organic matter content. The association between recovery rate and organic matter content was statistically significant. Conclusions: The present study identified a low recovery rate for an adapted centrifugation-flotation method, although this was similar...

  7. A comparative study of turbulence models for dissolved air flotation flow analysis

    International Nuclear Information System (INIS)

    Park, Min A; Lee, Kyun Ho; Chung, Jae Dong; Seo, Seung Ho

    2015-01-01

    The dissolved air flotation (DAF) system is a water treatment process that removes contaminants by attaching micro bubbles to them, causing them to float to the water surface. In the present study, two-phase flow of air-water mixture is simulated to investigate changes in the internal flow analysis of DAF systems caused by using different turbulence models. Internal micro bubble distribution, velocity, and computation time are compared between several turbulence models for a given DAF geometry and condition. As a result, it is observed that the standard κ-ε model, which has been frequently used in previous research, predicts somewhat different behavior than other turbulence models

  8. Coal surface control for advanced fine coal flotation. Final report, October 1, 1988--March 31, 1992

    Energy Technology Data Exchange (ETDEWEB)

    Fuerstenau, D.W.; Hanson, J.S.; Diao, J.; Harris, G.H.; De, A.; Sotillo, F. [California Univ., Berkeley, CA (United States); Somasundaran, P.; Harris, C.C.; Vasudevan, T.; Liu, D.; Li, C. [Columbia Univ., New York, NY (United States); Hu, W.; Zou, Y.; Chen, W. [Utah Univ., Salt Lake City, UT (United States); Choudhry, V.; Shea, S.; Ghosh, A.; Sehgal, R. [Praxis Engineers, Inc., Milpitas, CA (United States)

    1992-03-01

    The initial goal of the research project was to develop methods of coal surface control in advanced froth flotation to achieve 90% pyritic sulfur rejection, while operating at Btu recoveries above 90% based on run-of-mine quality coal. Moreover, the technology is to concomitantly reduce the ash content significantly (to six percent or less) to provide a high-quality fuel to the boiler (ash removal also increases Btu content, which in turn decreases a coal`s emission potential in terms of lbs SO{sub 2}/million Btu). (VC)

  9. Solvent extraction of Cu, Mo, V, and U from leach solutions of copper ore and flotation tailings.

    Science.gov (United States)

    Smolinski, Tomasz; Wawszczak, Danuta; Deptula, Andrzej; Lada, Wieslawa; Olczak, Tadeusz; Rogowski, Marcin; Pyszynska, Marta; Chmielewski, Andrzej Grzegorz

    2017-01-01

    Flotation tailings from copper production are deposits of copper and other valuable metals, such as Mo, V and U. New hydrometallurgical technologies are more economical and open up new possibilities for metal recovery. This work presents results of the study on the extraction of copper by mixed extractant consisting p -toluidine dissolved in toluene. The possibility of simultaneous liquid-liquid extraction of molybdenum and vanadium was examined. D2EHPA solutions was used as extractant, and recovery of individual elements compared for the representative samples of ore and copper flotation tailings. Radiometric methods were applied for process optimization.

  10. Quantification of Campylobacter spp. in chicken rinse samples by using flotation prior to real-time PCR

    DEFF Research Database (Denmark)

    Wolffs, Petra; Norling, Börje; Hoorfar, Jeffrey

    2005-01-01

    Real-time PCR is fast, sensitive, specific, and can deliver quantitative data; however, two disadvantages are that this technology is sensitive to inhibition by food and that it does not distinguish between DNA originating from viable, viable nonculturable (VNC), and dead cells. For this reason...... enrichment and amounts as low as 2.6 X 10(3) CFU/ml could be quantified. Furthermore, subjecting viable cells and dead cells to flotation showed that viable cells were recovered after flotation treatment but that dead cells and/or their DNA was not detected. Also, when samples containing VNC cells mixed...

  11. Separation of Molybdenum from Uranium based on sulphuric acid leaching by an ionic flotation technique

    International Nuclear Information System (INIS)

    Jdid, E.; Blazy, P.

    1989-01-01

    Molybdenum contained in uraniferous ores is made soluble during the leaching of the latter by sulphuric acid. It then can interfere in the uranium recovery operations and its throublesome effect depends on its concentration, or more particularly on the Mo/U ratio of the sulphuric solutions which result from the acid attack. The ionic flotation technique has been used in such cases to purify the uraniferous solutions from the molybdenum which they contain. The collector used to float molybdenum selectively in the presence of uranium is alpha-benzoid-oxime. The tests were carried out with synthetic H 2 SO 4 solutions and with commercial sulphuric leaching solutions. The recoveries obtained for a stoichiometric ratio of 1.5 are 99% and 86%, respectively, the uranium concentration being of the order of 5.10 -3 M. The floated concentrate assays approx. 15% in the case of synthetic solutions and approx. 14% for commercial solutions. The time for flotation is from 8 to 11 min. In the commercial solutions, the Mo/U ratio had been reduced from 0.5 to 0.09. 32 refs [fr

  12. Evaluation of the Cornell-Wisconsin centrifugal flotation technique for recovering trichostrongylid eggs from bovine feces.

    Science.gov (United States)

    Egwang, T G; Slocombe, J O

    1982-01-01

    Several variables in the Cornell-Wisconsin centrifugal flotation technique were studied using helminthologically sterile bovine feces to which known numbers of Haemonchus contortus eggs had been added. Neither mode of mixing (levigation versus conventional), volume (15-60 mL) of water used for making the feces water suspension nor specific gravity (1.20-1.33) of the sucrose flotation solution affected egg recovery. Optimal times for centrifugation at 264 x g of first the feces water and then the feces sucrose suspension were three and five minutes respectively. Under these conditions 62.6% of the eggs were recoverable and there was a linear relationship between the number of eggs recovered and those added to the feces. About 30% of the unrecovered eggs were found in the fecal debris retained on the strainer. About 5% of the unrecovered eggs were found in the supernatant discarded after the feces water centrifugation and also in the matrix of the viscous sucrose solution. Addition of the detergent Triton X-100 caused a decrease in egg recovery. False negatives were not encountered between 3 to 70 epg; at 1.44 epg there was only one in 14 samples. Optimum procedures for the technique are presented. PMID:7093809

  13. Bioleaching of a low grade sphalerite concentrate produced from flotation tailings

    Directory of Open Access Journals (Sweden)

    Javad Mehrabani

    2016-12-01

    Full Text Available In this research work, the zinc extraction was investigated, using bioleaching process from a low grade zinc concentrate which was produced from the accumulated flotation tailings. Zinc content was initially upgraded to 11.97% by flotation process. Bioleaching experiments were designed and carried out by a mixed culture of Acidithiobacillus ferrooxidans, Acidithiobacillus thiooxidans, Leptospirilium ferrooxidans, as well as a mixed moderate thermophile bacteria in the shake flasks. Effect of two types bacteria, indigenous bacteria accompany by concentrate sample, and added mixture of bacteria were evaluated. The term of indigenous bacteria refers to the bacteria which initially exist in the natural concentrate sample. The results showed that more than 87% and 94% of Zn was dissolved in the bioleaching condition of mesophile and moderate thermophile bacteria, respectively. Comparing bioleaching and leaching tests indicated that mesophile bacteria improved Zn extraction 36%, in which contribution of concentrate indigenous bacteria (test condition of non-inoculation and added mesophile mixed bacteria were equal to 34% and 66% of that improvement, respectively. In addition, moderate thermophile bacteria improved sphalerite leaching up to 38% in which contribution of concentrate indigenous bacteria and added moderate bacteria were about 50% separately.

  14. Improvement of calcium mineral separation contrast using anionic reagents: electrokinetics properties and flotation

    Science.gov (United States)

    Lafhaj, Z.; Filippov, L. O.; Filippova, I. V.

    2017-07-01

    The flotation separation of salt type calcium minerals is problematic, due to the similarities in their same active Ca2+ related site for interaction with anionic collectors and similar physicochemical characteristics such as solubility, zero-point charge, surface speciation and Ca-site density. The work was performed to achieve effective and selective separation of the calcium-minerals using pure minerals samples: orange calcite with Mg impurities, optic calcite with impurities level and an apatite. The pure samples surface was examined using techniques sensitive near-surface like infrared spectroscopy (FTIR) and chemical composition was obtained by ICPMS. The isoelectric point (IEP) and point of zero charge (PZC) in electrolyte were recorded using electrophoresis method at different ionic strengths of the solution. Mechanisms of charge development at the mineral-water interface are discussed. The time of contact as important parameter for the charge equilibrium was deduced from kinetics study and fixed to 30 minutes. The difference in the values obtained between IEP and PZSE can be explained by the presence of a specific adsorption of cations and anions on the surface. The effect of pure anionic collectors such as oleic and linoleic acid were studied. At low pH, both collectors lead to a good recovery for the calcites. The flotation recovery of optic calcite at pH 9 with sodium oleate is higher than with sodium linoleate. At alkaline pH, apatite showed a better recovery with sodium linoleate.

  15. Selective separation of virgin and post-consumer polymers (PET and PVC) by flotation method

    International Nuclear Information System (INIS)

    Burat, Firat; Gueney, Ali; Olgac Kangal, M.

    2009-01-01

    More and more polymer wastes are generated by industry and householders today. Recycling is an important process to reduce the amount of waste resulting from human activities. Currently, recycling technologies use relatively homogeneous polymers because hand-sorting waste is costly. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. At present, most waste polymers cause serious environmental problems. Burning polymers for recycling is not practiced since poisonous gases are released during the burning process. Particularly, polyvinyl chloride (PVC) materials among waste polymers generate hazardous HCl gas, dioxins containing Cl, etc., which lead to air pollution and shorten the life of the incinerator. In addition, they make other polymers difficult to recycle. Both polyethylene terephthalate (PET) and PVC have densities of 1.30-1.35 g/cm 3 and cannot be separated using conventional gravity separation techniques. For this reason, polymer recycling needs new techniques. Among these techniques, froth flotation, which is also used in mineral processing, can be useful because of its low cost and simplicity. The main objective of this research is to recycle PET and PVC selectively from post-consumer polymer wastes and virgin polymers by using froth flotation. According to the results, all PVC particles were floated with 98.8% efficiency in virgin polymer separation while PET particles were obtained with 99.7% purity and 57.0% efficiency in post-consumer polymer separation.

  16. Selective separation of virgin and post-consumer polymers (PET and PVC) by flotation method.

    Science.gov (United States)

    Burat, Firat; Güney, Ali; Olgaç Kangal, M

    2009-06-01

    More and more polymer wastes are generated by industry and householders today. Recycling is an important process to reduce the amount of waste resulting from human activities. Currently, recycling technologies use relatively homogeneous polymers because hand-sorting waste is costly. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. At present, most waste polymers cause serious environmental problems. Burning polymers for recycling is not practiced since poisonous gases are released during the burning process. Particularly, polyvinyl chloride (PVC) materials among waste polymers generate hazardous HCl gas, dioxins containing Cl, etc., which lead to air pollution and shorten the life of the incinerator. In addition, they make other polymers difficult to recycle. Both polyethylene terephthalate (PET) and PVC have densities of 1.30-1.35g /cm(3) and cannot be separated using conventional gravity separation techniques. For this reason, polymer recycling needs new techniques. Among these techniques, froth flotation, which is also used in mineral processing, can be useful because of its low cost and simplicity. The main objective of this research is to recycle PET and PVC selectively from post-consumer polymer wastes and virgin polymers by using froth flotation. According to the results, all PVC particles were floated with 98.8% efficiency in virgin polymer separation while PET particles were obtained with 99.7% purity and 57.0% efficiency in post-consumer polymer separation.

  17. Depressing Iron Mineral by Metallic-Starch Complex (MSC in Reverse Flotation and Its Mechanism

    Directory of Open Access Journals (Sweden)

    Tao Yue

    2018-02-01

    Full Text Available A series of metallic-starch complex (MSC solutions, synthesized by mixing relevant metallic ionic solutions with the caustic starch solution, were used as the flotation depressants to investigate their depressing effects on hematite ore. The MSC is a nano-sized colloidal complex which is configured by hydrophilic metallic hydroxide as the colloidal nucleus on which starch and hydroxyl complex are adsorbed, resulting in a larger molecule than starch itself. The flotation tests showed that the depressing abilities of various MSC (Fe3+, Zn2+, Pb2+ and Mg2+ on the iron minerals were higher than the caustic starch, and the order of depression ability was: Zn2+-starch > Pb2+-starch > Fe3+-starch > Mg2+-starch > caustic starch. Based on the adsorption analysis, the high depressing ability of the MSC arose from increasing the adsorption density of starch on iron minerals and slightly reducing the absorption of the collector dodecylamine. Adsorption behaviour also indicated that the adsorption of the MSC on mineral surfaces was thicker than the caustic starch, and among various MSC the adsorption of Fe3+-starch exhibited the thickest adsorption layer while that of Mg2+-starch the thinnest. Zeta potential indicated that with a weaker electronegativity than the caustic starch, MSC adsorbed onto iron minerals more easily, and the strong electrostatic adsorption with the aid of the hydrogen bonding and chemisorption agreed well with the high depressing ability of the MSC.

  18. Investigation of thermal treatment on selective separation of post consumer plastics prior to froth flotation

    International Nuclear Information System (INIS)

    Guney, Ali; Poyraz, M. Ibrahim; Kangal, Olgac; Burat, Firat

    2013-01-01

    Highlights: • Both PET and PVC have nearly the same densities. • The best pH value will be 4 for optimizing pH values. • Malic acid gave the best results for selective separation of PET and PVC. - Abstract: Plastics have become the widely used materials because of their advantages, such as cheapness, endurance, lightness, and hygiene. However, they cause waste and soil pollution and they do not easily decompose. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. Depending on their surface characteristics, these plastics can be separated from each other by flotation method which is useful mineral processing technique with its low cost and simplicity. The main objective of this study is to investigate the flotation characteristics of PET and PVC and determine the effect of plasticizer reagents on efficient plastic separation. For that purpose, various parameters such as pH, plasticizer concentration, plasticizer type, conditioning temperature and thermal conditioning were investigated. As a result, PET particles were floated with 95.1% purity and 65.3% efficiency while PVC particles were obtained with 98.1% purity and 65.3% efficiency

  19. Investigation of thermal treatment on selective separation of post consumer plastics prior to froth flotation.

    Science.gov (United States)

    Guney, Ali; Poyraz, M Ibrahim; Kangal, Olgac; Burat, Firat

    2013-09-01

    Plastics have become the widely used materials because of their advantages, such as cheapness, endurance, lightness, and hygiene. However, they cause waste and soil pollution and they do not easily decompose. Many promising technologies are being investigated for separating mixed thermoplastics, but they are still uneconomical and unreliable. Depending on their surface characteristics, these plastics can be separated from each other by flotation method which is useful mineral processing technique with its low cost and simplicity. The main objective of this study is to investigate the flotation characteristics of PET and PVC and determine the effect of plasticizer reagents on efficient plastic separation. For that purpose, various parameters such as pH, plasticizer concentration, plasticizer type, conditioning temperature and thermal conditioning were investigated. As a result, PET particles were floated with 95.1% purity and 65.3% efficiency while PVC particles were obtained with 98.1% purity and 65.3% efficiency. Copyright © 2013 Elsevier Ltd. All rights reserved.

  20. Application of dissolved air flotation process for industrial sludge thickening: A laboratory-scale study

    Directory of Open Access Journals (Sweden)

    Ali Atamaleki

    2017-01-01

    Full Text Available Aims: Increasing population density in cities has led to an increase in industrial and municipal wastewater sludge generation volume. Dissolved air flotation (DAF can widely be used for water and wastewater treatment. The aim of our study is to evaluate some DAF design parameters on biological sludge thickening which generated from an industrial wastewater treatment plant. Materials and Methods: This experimental research had been carried out as a laboratory-scale study on DAF process to thickening of the biological sludge. The required amount of sludge was taken once from the Amikabir industrial town wastewater treatment plant in Kashan, Iran. After determination of optimal recycling rate, pH, and coagulant dose, effects of pressure (3, 5, and 7 atm, flotation time (5 and 10 min, and coagulant addition were evaluated on DAF process efficiency. Results: According to this investigation results, the optimal pH and dose of coagulant were obtained 7.5 and 200 mg/L, respectively. Maximum process efficiency for the reduction of total dissolved solids (TDSs, total solids (TSs, and turbidity parameters was 61.01%, 84.02%, and 97%, respectively. Furthermore, the results showed that in contrast to time, coagulant addition and pressure have significant effect on DAF process. Conclusion: DAF process had suitable thickening efficiency to removal of TDS, TS, and turbidity on biological activated sludge.

  1. Evaluating the efficacy of a centrifugation-flotation method for extracting Ascaris ova from soil.

    Science.gov (United States)

    Cranston, Imogen; Teoh, Penelope J; Baker, Sarah M; Sengupta, Mita E; Ensink, Jeroen H J

    2016-07-01

    Soil transmitted helminths (STH) continue to be associated with high burdens of disease, with an estimated 1.45 billion people infected with STH globally. The promotion and construction of latrines is considered the first barrier to prevent transmission of STH. The absence of a reliable method to extract STH ova from soil makes it challenging to examine whether the use of latrines may or may not have an effect on environmental contamination with ova. The present study evaluated the recovery rate of a method developed to extract STH ova from soil. The adapted centrifugation and flotation technique was applied to 15 soil types, which were seeded with Ascaris suum ova. Soil type, soil moisture content, soil texture and organic matter content were assessed for each soil sample. The average ova recovery rate was 28.2%, with the recovery rate of the method decreasing with increasing soil moisture content, particle size and organic matter content. The association between recovery rate and organic matter content was statistically significant. The present study identified a low recovery rate for an adapted centrifugation-flotation method, although this was similar to the recovery rate demonstrated by other methods developed for soil. Soil organic matter content was significantly associated with ova recovery rates. © The Author 2016. Published by Oxford University Press on behalf of Royal Society of Tropical Medicine and Hygiene. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  2. Flotation Assembly of Large-Area Ultrathin MWCNT Nanofilms for Construction of Bioelectrodes

    Directory of Open Access Journals (Sweden)

    Andrew J. Gross

    2017-10-01

    Full Text Available We report a simple, versatile, and rapid method for the fabrication of optically-transparent large-area carbon nanotube (CNT films via flotation assembly. After solvent-induced assembly, floating films were transferred to a flat supporting substrate to form conductive and transparent CNT film electrodes. The resulting electrodes, with uniform 40 ± 20 nm multi-walled CNT (MWCNT layers, were characterized by electrochemical and microscopy methods. The flotation method does not require specialized thin-film instrumentation and avoids the need for surfactants and pre-oxidized CNTs which can hamper electrochemical performance. A proof-of-concept nanostructured bioelectrode demonstrating high sensitivity for glucose was developed with an electropolymerized poly(pyrene-adamantane layer for host–guest immobilization of active β-cyclodextrin tagged GOx enzymes. The polymer provides pyrene groups for cross-linking to CNTs and pendant adamantane groups for binding the β-cyclodextrin groups of the tagged enzyme. This demonstration offers a new approach for the preparation of stable and transparent CNT film electrodes with attractive electrochemical properties towards future photobio- and bio-electrochemical fuel cells, electrochemical sensors, and electroanalysis.

  3. The behavior of thiourea and flotation reagents in zinc electrowinning circuits

    Science.gov (United States)

    MacKinnon, D. J.; Dutrizac, J. E.; Brannen, J. M.; Hardy, D. J.

    1988-04-01

    The effect of thiourea and flotation reagents on the electrowinning of zinc from industrial electrolytes was studied, and all the compounds were found to reduce the zinc deposition current efficiency and to change the properties of the zinc deposits. The effectiveness of activated carbon, two-stage cementation, and hot acid leaching on the destruction/removal of the organic compounds also was addressed. Activated carbon pretreatment of thiourea-containing electrolytes restored the current efficiency for 1-hour zinc deposits to values comparable to those obtained for thiourea-free electrolytes. The activated carbon pretreatment, however, altered the deposit morphology and orientation, but produced a cyclic voltammogram similar to that of the thiourea-free solution. Two-stage cementation did not counteract the harmful effects of thiourea. Hot acid leaching destroyed the thiourea but generated large concentrations of ferrous ion that reduced the current efficiency. The ferrous concentrations, however, were readily controlled by KMnO4 or MnO2 oxidation. None of the treatment options (activated carbon, two-stage cementation, or hot acid leaching) was effective in controlling the flotation reagents, and their moderately harmful effect on zinc electrowinning persisted. Even low concentrations of these reagents polarized zinc deposition, and this resulted in a “glue-type” zinc deposit.

  4. Anisotropic adsorption of oleate on diaspore and kaolinite crystals: Implications for their flotation separation

    Science.gov (United States)

    Xu, Longhua; Hu, Yuehua; Dong, Faqin; Gao, Zhiyong; Wu, Houqin; Wang, Zhen

    2014-12-01

    Comparative studies of flotation of oleate on diaspore and kaolinite in different particle size fractions (0.075-0.038 mm, 0.038-0.01 mm, 0-0.01 mm) are presented to investigate the influences of particle size. The flotation results show that the kaolinite recovery increases with a decrease in particle size, while the case of diaspore is the opposite. Chemisorptions of anionic oleate collector on the surface Al sites of the negatively charged diaspore and kaolinite are confirmed by zeta potential and FTIR measurements. Anisotropic surface broken bond densities are calculated based on surface crystal chemistry to characterize anisotropic wettability of mineral crystals. The increasing order of broken bond densities (Db) and hydrophobicity for different crystal planes of diaspore and kaolinite correlate well with increasing the number of broken Alsbnd O bonds. The anisotropic adsorption of oleate on different crystal planes of diaspore and kaolinite are studied in terms of interaction energies computed by molecular dynamics (MD) simulations. The oleate is adsorbed more readily on (0 1 0) than (0 0 1) for diaspore. As for kaolinite, the oleate adsorption is considerably less on (0 0 1) as compared to (1 10). The conclusions drawn from purely theoretical computations are in good agreement with our experimental contact angle results.

  5. Effect of Dissolved Air Flotation Process on Thickening of Activated Sludge

    Directory of Open Access Journals (Sweden)

    Atamaleki A.

    2016-12-01

    Full Text Available Abstract Aims: Sludge is an inescapable component of all wastewaters that originated from their treatment. dissolved air flotation (DAF process as an alternative clarifier is used in treatment of drinking water, pretreatment of wastewater, and as a phase separator in sludge activation processes. This study aimed to calibrated the usage of DAF process in a laboratory scale and under various conditions, to achieve the optimum efficiency in recycling the activated sludge. Instrument & Methods: In this experimental study, of Kashan's Shahid Beheshti hospital and immediately transported to the laboratory. The optimal dose of polyaluminum chloride coagulant and pH was determined and then applied in DAF process. Finally turbidity, electrical conductivity (EC and total solids (TS parameters were measured and compared with control sample. Findings: The optimal pH and optimal dose of coagulant were 6.5 and 25mg/l, respectively. Also Optimal process efficiency to reduce EC, TS and turbidity parameters were 23.4, 44.5 and 88%, respectively. Conclusion: Dissolved air flotation process removes the turbidity, EC and TS effectively; however, it has minimal impact on EC and TS.

  6. Bioleaching of a low grade sphalerite concentrate produced from tailings flotation

    International Nuclear Information System (INIS)

    Mehrabani, J. V.; Shafaei, S. Z.; Noaparast, M.; Mousavi, S. M.

    2016-01-01

    In this research, the zinc extraction from a low grade zinc concentrate produced from the accumulated flotation tailings was investigated using the bio leaching process. Zinc content was initially upgraded to 11.97% through flotation process. Bio leaching experiments were designed and carried out by a mixed culture of Acidithiobacillus ferro oxidans, Acidithiobacillus thio oxidans, Leptospirilium ferro oxidans, as well as a mixed moderate thermophile bacteria in the shake flasks. The effect of two bacteria types, the indigenous bacteria accompanied by concentrate sample and added mixture of bacteria, were evaluated. The term of indigenous bacteria refers to the bacteria which initially exists in the natural concentrate sample. The results showed that more than 87% and 94% of Zn was dissolved in the bio leaching condition of mesophile and moderate thermophile bacteria, respectively. Comparing the bio leaching and leaching tests indicate that mesophile bacteria improves the Zn extraction by 36%, in which the contribution of concentrate indigenous bacteria (test condition of non-inoculation) and added mesophile mixed bacteria were equal to 34% and 66%, respectively. In addition, moderate thermophile bacteria improves the sphalerite leaching up to 38% in which contribution of the concentrate indigenous bacteria and added moderate thermophile bacteria were about 50% separately.

  7. Separation of polycarbonate and acrylonitrile–butadiene–styrene waste plastics by froth flotation combined with ammonia pretreatment

    International Nuclear Information System (INIS)

    Wang, Chong-qing; Wang, Hui; Liu, Qun; Fu, Jian-gang; Liu, You-nian

    2014-01-01

    Highlights: • Ammonia treatment changes selectively floatability of PC. • The effects of ammonia on PC were investigated through contact angle and XPS. • Reactions between ammonia and PC surface make PC more hydrophilic. • PC and ABS mixtures with different particle sizes were separated effectively. - Abstract: The objective of this research is flotation separation of polycarbonate (PC) and acrylonitrile–butadiene–styrene (ABS) waste plastics combined with ammonia pretreatment. The PC and ABS plastics show similar hydrophobicity, and ammonia treatment changes selectively floatability of PC plastic while ABS is insensitive to ammonia treatment. The contact angle measurement indicates the dropping of flotation recovery of PC is ascribed to a decline of contact angle. X-ray photoelectron spectroscopy demonstrates reactions occur on PC surface, which makes PC surface more hydrophilic. Separation of PC and ABS waste plastics was conducted based on the flotation behavior of single plastic. At different temperatures, PC and ABS mixtures were separated efficiently through froth flotation with ammonia pretreatment for different time (13 min at 23 °C, 18 min at 18 °C and 30 min at 23 °C). For both PC and ABS, the purity and recovery is more than 95.31% and 95.35%, respectively; the purity of PC and ABS is up to 99.72% and 99.23%, respectively. PC and ABS mixtures with different particle sizes were separated effectively, implying that ammonia treatment possesses superior applicability

  8. Discovery of a Novel Cationic Surfactant: Tributyltetradecyl-Phosphonium Chloride for Iron Ore Flotation: From Prediction to Experimental Verification

    Directory of Open Access Journals (Sweden)

    Pan Chen

    2017-12-01

    Full Text Available In this work, tributyltetradecyl-phosphonium chloride (TTPC, has been first introduced to be a novel and efficient cationic surfactant for cationic reverse flotation separation of quartz from magnetite. The first-principles density functional theory calculations, Zeta potential measurements and adsorption isotherm measurements consistently predict that TTPC may be a promising collector that is better than dodecyl triethyl ammonium chloride (DTAC, based on the facts that TTPC and DTAC both prefer to physically adsorb on the quartz surface owing to electrostatic force, but the active part (P+(C4H93 of TTPC takes much more positive charges than that (N+(CH33 of DTAC. The micro-flotation and Bench-scale flotation results further verify that TTPC presents a stronger collecting power and much better selectivity for iron ore reverse flotation in comparison to the conventional collector DTAC. Furthermore, the corresponding adsorption mechanism of TTPC on the quartz have also been investigated in detail. This work might show a good example to discover a potential candidate collector by analogy with a known excellent collector based on reasonable prediction.

  9. Separation of polycarbonate and acrylonitrile-butadiene-styrene waste plastics by froth flotation combined with ammonia pretreatment.

    Science.gov (United States)

    Wang, Chong-Qing; Wang, Hui; Liu, Qun; Fu, Jian-Gang; Liu, You-Nian

    2014-12-01

    The objective of this research is flotation separation of polycarbonate (PC) and acrylonitrile-butadiene-styrene (ABS) waste plastics combined with ammonia pretreatment. The PC and ABS plastics show similar hydrophobicity, and ammonia treatment changes selectively floatability of PC plastic while ABS is insensitive to ammonia treatment. The contact angle measurement indicates the dropping of flotation recovery of PC is ascribed to a decline of contact angle. X-ray photoelectron spectroscopy demonstrates reactions occur on PC surface, which makes PC surface more hydrophilic. Separation of PC and ABS waste plastics was conducted based on the flotation behavior of single plastic. At different temperatures, PC and ABS mixtures were separated efficiently through froth flotation with ammonia pretreatment for different time (13 min at 23 °C, 18 min at 18 °C and 30 min at 23 °C). For both PC and ABS, the purity and recovery is more than 95.31% and 95.35%, respectively; the purity of PC and ABS is up to 99.72% and 99.23%, respectively. PC and ABS mixtures with different particle sizes were separated effectively, implying that ammonia treatment possesses superior applicability. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Treating Stress-Related Pain with the Flotation Restricted Environmental Stimulation Technique: Are There Differences between Women and Men?

    Directory of Open Access Journals (Sweden)

    Sven Å Bood

    2009-01-01

    Full Text Available The aim of the present study was to explore, for the first time, sex differences among patients diagnosed with stress-related pain before and after flotation restricted environmental stimulation technique (REST treatment, delivered 12 times during seven weeks. The present study included 88 patients (69 women, 19 men from three different studies (post hoc analysis. They had been diagnosed by a physician as having chronic stress-related muscle tension pain. The analyses indicated that the flotation-REST treatment had beneficial effects on stress, anxiety, depression, sleep quality and pain and that there were few sex differences. Women were more depressed than men before treatment, but after treatment there was no difference between sexes. However, there was a sex difference in the ability to endure experimentally induced pain, suggesting that men exhibited greater endurance both before and after the flotation-REST treatment. The results also showed, for the first time, that both sexes improved their ability to endure experimentally induced pain (higher scores for upper pain threshold following the successful flotation-REST pain treatment.

  11. Design of a High Speed Planing Hull with a Cambered Step and Surface Piercing Hydrofoils

    Science.gov (United States)

    2014-06-01

    Knowing that the planing hull is symmetric, and accounting for the symmetry plane benefits, the inertial reference frame was cut in half, as...performing waterjet . a1=3.19e-1; %max = 3.81e-1 b=-2.25e-2; %max= -2.09e-2 c=-1.04e-3; %max = -3.84e-4 d=2.01e-4; %max = 2.05e-4

  12. Association of solvent extraction and liquid-liquid flotation processes for metal recovery

    International Nuclear Information System (INIS)

    Puget, Flavia P.; Mendonca, Luciano A. de; Massarani, Giulio

    2000-01-01

    From the batch solvent extraction process, in this work it has been carried out a preliminary study aiming the determination of the optimal operating conditions for zirconium recovery (10 ppm) using alamine 336 (tricaprylylamine) as extractor. The results have shown that the extraction takes place instantaneously (5s of manual agitation) and that at pH around 2.0 the extraction efficiency is up to 98-99% for an aqueous/organic phase volumetric ratio of 10. Based on these results, it is proposed to evaluate the possibility of using of a pioneering technology for metal recovery at low concentrations, using a experimental set-up that associates standard solvent extraction process with liquid-liquid flotation process. (author)

  13. Separation tests of heavy metals in samples of industrial wastes through flotation

    International Nuclear Information System (INIS)

    Abrego L, J.

    1995-12-01

    Samples of residual muds, taken at the exit of the filter-press of the water treatment plant of a galvanoplastics industry in Lerma, Estado de Mexico, its were prepared for its qualitative and quantitative analysis. Likewise, the residual waters of the cistern located at the end of the electrodeposition process, was subjected to qualitative chemical analysis for the neutron activation technique and to quantitative analysis by atomic absorption spectrometry. The samples were treated by a flotation process by means of the one which it was studied the heavy metals removal. The results show that the AP-845 collector is the one that better it fulfilled the objectives since, it solves the problem, unless by the copper that although their concentration in the residual waters drop a lot, it was not inside the standard. (Author)

  14. Engineering development of advanced physical fine coal cleaning technologies - froth flotation

    Energy Technology Data Exchange (ETDEWEB)

    Ferris, D.D.; Bencho, J.R. [ICF Kaiser Engineers, Inc., Pittsburgh, PA (United States)

    1995-11-01

    In 1988, ICF Kaiser Engineers was awarded DOE Contract No. DE-AC22-88PC88881 to research, develop, engineer and design a commercially acceptable advanced froth flotation coal cleaning technology. The DOE initiative is in support of the continued utilization of our most abundant energy resource. Besides the goal of commercialability, coal cleaning performance and product quality goals were established by the DOE for this and similar projects. primary among these were the goals of 85 percent energy recovery and 85 percent pyrite rejection. Three nationally important coal resources were used for this project: the Pittsburgh No. 8 coal, the Upper Freeport coal, and the Illinois No. 6 coal. Following is a summary of the key findings of this project.

  15. Evaluation of biosurfactant obtained from Lactobacillus pentosus as foaming agent in froth flotation.

    Science.gov (United States)

    Vecino, X; Devesa-Rey, R; Cruz, J M; Moldes, A B

    2013-10-15

    This study analyzes the kinetics of sediment sorption on two chemical surfactants (Tween 20 and SDS) and a biotechnologically produced surfactant (obtained from Lactobacillus pentosus). Biosurfactants were produced by fermentation of hemicellulosic sugars from vineyard pruning waste supplied as a substrate to L. pentosus. Results obtained showed that almost no SDS was adsorbed onto the sediments, whereas Tween 20 and biosurfactants from L. pentosus were absorbed after a few minutes. Kinetic models revealed that adsorption of surfactant onto riverbed sediments is governed not only by an intra-particle diffusion model (evaluated by the Weber and Morris model), but also by surface reaction models (evaluated by first, second, third order equations and Elovich equation), showing the best fit when employing the Elovich model. The adsorption properties showed by biosurfactant from L. pentosus onto sediments present it as a potential foaming agent in froth flotation. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Evaluation of dissolved air flotation and membrane filtration for drinking water treatment

    International Nuclear Information System (INIS)

    Van Benschoten, J.; Martin, C.; Schaefer, J.; Xu, L.; Franceschini, S.

    2002-01-01

    Laboratory and pilot-scale testing was conducted to evaluate the use of dissolved air flotation (DAF) followed by membrane filtration (MF) for drinking water treatment. At the laboratory scale, four water samples of varying water quality were tested. Pilot- scale DAF and MF plants located at the City of Buffalo Water Treatment facility utilized Lake Erie as a raw water source to evaluate this combination of treatment processes. A polyaluminum coagulant was used throughout the study. Study results demonstrated beneficial effects of coagulant addition in extending MF run time. Pilot testing showed additional benefits to using DAF as a pretreatment step to MF. In all testing, MF produced excellent water quality. Particulate matter appeared more important than concentration or type of dissolved organic matter in membrane fouling. (author)

  17. Ion flotation of uranium contained in industrial phosphoric acid with collector recycling

    International Nuclear Information System (INIS)

    Jdid, E.; Blazy, P.; Bessiere, J.

    1985-01-01

    Uranium has been recovered from wet-process phosphoric acid (30% P 2 O 5 ) by ion flotation with an anionic organophosphorous collector. Recoveries greater than 90% were obtained even at temperatures of about 60 C, the uranium concentrate, which was collected in the froth as a precipitate, containing 7 to 10% U. Collector consumption without recycling of the surface-active reagent was about 12 kg/kg U. Much of the reagent, however, can be recovered for recycling by attack with sodium hydroxide on the floated phase after filtration. This enables a precipitate containing about 30% U to be produced and decreases collector consumption to about 3 kg/kg U. The results were obtained in laboratory-scale experiments on industrial wet-process acid. (author)

  18. Treatment of oily water by flotation; Tratamiento de aguas oleosas por flotacion

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz O, H.B

    2002-07-01

    The operation of the nuclear power plants such as Laguna Verde (CLV) with nuclear reactors of the boiling water type (BWR) produce radioactive waste solids, liquids and gaseous which require of a special treatment in their operation and arrangement. Such is the case of the liquid wastes from CLV which are a mixture of water and synthetic oils coming from leaks and spilling by pressure of maintenance of electro-mechanical equipment associated to the performance of the nuclear power plant. This mixture of water and spent oils is pretreated by means of sedimentation, centrifugation and evaporation. However the realized efforts by the CLV, the spent oil obtained from the pretreatment contains concentrations of radioactive material higher than the tolerance limits established in the normative in force in radiological safety (0.37 Bq m L{sup -1} for {sup 60} Co and {sup 54} Mn). In this context it was necessary to design an efficient treatment system and economically profitable which separates the oil, the heavy metals and the leftovers of radioactive material that could be present in water, with the purpose of fulfil with the Mexican Official Standards corresponding for its unload or even it can reuse it in the wash process of treated oil. The treatment system of oily water waste consists of: a) Coagulation-flocculation, b) Flotation system with modified air dissolved (DAFm). The proposed flotation process allows to reach a higher separation efficiencies of: Concentration of greases and oils: 94.11 %; Turbidity: 98.6 %; {sup 60} Co: 82.3 % ; Co: 94.8 % and Cr: 99.9 % (Author)

  19. Isolation by sugar flotation has no direct effect on the hatching success of zooplankton resting eggs

    Directory of Open Access Journals (Sweden)

    Dunja Lukic

    2016-03-01

    Full Text Available Zooplankton in temporary waters produces resting stages to survive recurrent dry periods. Branchiopod crustaceans (i.e., cladocerans, large branchiopods overcome these periods in the form of resting eggs buried in the sediment. Examining the diversity in the resting egg banks allows for a more accurate estimation of biodiversity of aquatic ecosystems than looking only at the active communities. The isolation of resting eggs from the sediment may be achieved by the sugar flotation method, which usually results in higher density and diversity than untreated samples (i.e., incubated in the sediment. We tested the effect of sugar isolation and centrifugation on the hatching success of resting eggs already isolated from sediment in order to reveal any direct effects on hatching success. We used four different branchiopod species, Daphnia magna, Moina brachiata, Branchinecta orientalis, and Triops cancriformis. Although we hypothesised that osmotic stress caused by sugar and centrifuging influence the hatching success either positively (e.g., faster activation as a response to osmotic changes or negatively (destroyed by centrifugation, we found no significant difference either in the timing or rate of hatching between centrifuged and non-centrifuged eggs. Once the eggs are exposed to light and/or oxygen availability by being removed from the sediment, the centrifugation process does not have any additional effect on their hatching. Regardless of treatment, we found a significant difference in the hatching timing in the two major groups, with large branchiopods hatching earlier than cladocerans. We found that the sugar flotation method itself does not influence the hatching fraction of branchiopod resting eggs (implying no adverse effect on their viability and its success in enhancing hatching can be attributed to its efficiency in removing eggs from the sediment.

  20. Abnormal gel flotation caused by contrast media during adrenal vein sampling.

    Science.gov (United States)

    Lima-Oliveira, Gabriel; Lippi, Giuseppe; Salvagno, Gian Luca; Gelati, Matteo; Bassi, Antonella; Contro, Alberto; Pizzolo, Francesca; Guidi, Gian Cesare

    2016-10-15

    During adrenal venous sampling (AVS) procedure, radiologists administer a contrast agent via the catheter to visualize the proper catheter position. A patient with primary aldosteronism diagnostic-hypothesis was admitted for AVS. A venogram was performed to
confirm the catheter's position with 2mL of Iopamidol 300 mg/mL. Samples were collected with syringe connected to a hydrophilic coated catheter by low-pressure aspiration from each of the four collection sites: inferior vena cava in the suprarenal portion, inferior vena cava in the infrarenal portion, left adrenal vein, and right adrenal vein; then immediately transferred from syringe to tubes with gel separator. All tubes were centrifuged at 1200 x g for 10 minutes. At the end of centrifugation process, primary blood tubes containing blood from inferior vena cava and left adrenal vein exhibited the standard gel separator barrier, while tubes from right adrenal vein showed abnormal flotation of gel separator. The radiologist confirmed the usage of 2.6 mL instead of 2.0 mL of Iopamidol 300 mg/mL. This iodinated contrast media, with 1.33 g/cm 3 of density, was used close to the right adrenal vein due to some difficulty to access it. The abnormal flotation of gel separator in samples taken from right adrenal vein can be explained by the usage of the iodinated
contrast media. We suggest using plain-tubes (without gel separator) for AVS in order to avoid preanalytical nonconformities. Moreover, a blood volume equivalent to twice the catheter extension should be discarded to eliminate residual contrast media before collection of samples for laboratory assays.

  1. Optimization of Cu-Zn Massive Sulphide Flotation by Selective Reagents

    Science.gov (United States)

    Soltani, F.; Koleini, S. M. J.; Abdollahy, M.

    2014-10-01

    Selective floatation of base metal sulphide minerals can be achieved by using selective reagents. Sequential floatation of chalcopyrite-sphalerite from Taknar (Iran) massive sulphide ore with 3.5 % Zn and 1.26 % Cu was studied. D-optimal design of response surface methodology was used. Four mixed collector types (Aer238 + SIPX, Aero3477 + SIPX, TC1000 + SIPX and X231 + SIPX), two depressant systems (CuCN-ZnSO4 and dextrin-ZnSO4), pH and ZnSO4 dosage were considered as operational factors in the first stage of flotation. Different conditions of pH, CuSO4 dosage and SIPX dosage were studied for sphalerite flotation from first stage tailings. Aero238 + SIPX induced better selectivity for chalcopyrite against pyrite and sphalerite. Dextrin-ZnSO4 was as effective as CuCN-ZnSO4 in sphalerite-pyrite depression. Under optimum conditions, Cu recovery, Zn recovery and pyrite content in Cu concentrate were 88.99, 33.49 and 1.34 % by using Aero238 + SIPX as mixed collector, CuCN-ZnSO4 as depressant system, at ZnSO4 dosage of 200 g/t and pH 10.54. When CuCN was used at the first stage, CuSO4 consumption increased and Zn recovery decreased during the second stage. Maximum Zn recovery was 72.19 % by using 343.66 g/t of CuSO4, 22.22 g/t of SIPX and pH 9.99 at the second stage.

  2. Novel amphiphiles with preorganized functionalities-formation of Langmuir-films and efficiency in mineral flotation.

    Science.gov (United States)

    Müller, P U; Akpo, C C; Stöckelhuber, K W; Weber, E

    2005-06-30

    Based on the principle of supramolecular preorganization, three different types of new oligofunctional surfactants have been designed and prepared differing in both the degree of conformational flexibility and the hydrophilic-lipophilic balance of their structures due to the chosen building blocks including rather rigid and shape-persistent backbones or a dendritic subunit. Surface-active properties of the oligofunctional surfactants involving critical micellization concentration, surface tension at cmc, effectiveness of surface tension reduction, and the efficiency of adsorption were determined by use of the surface tension isotherms, respectively. In particular the amino-acid-based amphiphiles show remarkable surface-active properties with the adsorption at the air/water interface and also the aggregation to micelles starting at very low concentration. By analysis of the surface pressure-surface area isotherms interesting information on the packing behavior and orientation of the amphiphilic molecules in relation to the molecular structure could be obtained. Moreover, limiting area and collapse pressure of the Langmuir-films were determined. Morphological observation of the dynamic process of monolayer compression at the air/water interface was carried out by Brewster angle microscopy illustrating several phase states visualized as snap shots. Furthermore, the effectiveness of the new surfactants acting as collecting agents in the process of flotation using the model mineral fluorite was studied. A surprisingly high recovery of the mineral was obtained for the surfactants with constricted flexibility. The flotation plots clearly manifest that bundling of surfactant subunits by tethering to an aromatic core or by dendritic branching is profitable, indicating that effects of preorganization of the oligofunctional surfactant molecules are important.

  3. Removal of natural organic matter and arsenic from water by electrocoagulation/flotation continuous flow reactor

    International Nuclear Information System (INIS)

    Mohora, Emilijan; Rončević, Srdjan; Dalmacija, Božo; Agbaba, Jasmina; Watson, Malcolm; Karlović, Elvira; Dalmacija, Milena

    2012-01-01

    Highlights: ► A continuous electrocoagulation/flotation reactor was designed built and operated. ► Highest NOM removal according to UV 254 was 77% relative to raw groundwater. ► Highest NOM removal accordance to DOC was 71%, relative to raw groundwater. ► Highest As removal archived was 85% (6.2 μg/l), relative to raw groundwater. ► Specific reactor energy and electrode consumption was 1.7 kWh/m 3 and 66 g Al/m 3 . - Abstract: The performance of the laboratory scale electrocoagulation/flotation (ECF) reactor in removing high concentrations of natural organic matter (NOM) and arsenic from groundwater was analyzed in this study. An ECF reactor with bipolar plate aluminum electrodes was operated in the horizontal continuous flow mode. Electrochemical and flow variables were optimized to examine ECF reactor contaminants removal efficiency. The optimum conditions for the process were identified as groundwater initial pH 5, flow rate = 4.3 l/h, inter electrode distance = 2.8 cm, current density = 5.78 mA/cm 2 , A/V ratio = 0.248 cm −1 . The NOM removal according to UV 254 absorbance and dissolved organic matter (DOC) reached highest values of 77% and 71% respectively, relative to the raw groundwater. Arsenic removal was 85% (6.2 μg As/l) relative to raw groundwater, satisfying the drinking water standards. The specific reactor electrical energy consumption was 17.5 kWh/kg Al. The specific aluminum electrode consumption was 66 g Al/m 3 . According to the obtained results, ECF in horizontal continuous flow mode is an energy efficient process to remove NOM and arsenic from groundwater.

  4. Using statistical experimental design techniques to determine the most effective variables for the control of the flotation deinking of mixed recycled paper grades

    CSIR Research Space (South Africa)

    Pauck, WJ

    2012-01-01

    Full Text Available properties. Samples of newsprint, magazines, and two grades of mixed office waste were pulped and deinked by flotation and washing in the laboratory. Handsheets were formed and measured for brightness, residual ink concentration and yield. A Plackett...

  5. Adsorption of sodium dodecyl sulfate onto precipitate in treatment of vat dark blue BO by dissolved air flotation.

    Science.gov (United States)

    Xia, Hongyun; Zhao, Xuyun; Zhao, Xiang; Yao, Ping; Zhang, Haoyu

    2017-07-03

    Vat dark blue BO-simulated wastewater was treated by dissolved air flotation (DAF). In this process, the interactions of sodium dodecyl sulfate (SDS) and resulting DAF process precipitates were investigated by infrared spectroscopy and kinetic methods. Fourier transform infrared analysis revealed that γ values (cm -1 ) for asymmetric and symmetric stretching vibrations of CH 2 groups for SDS-treated precipitation shifted toward higher in comparison to pure SDS, showing strong SDS and precipitate interactions. This showed the chemical adsorption of SDS onto precipitate surfaces. Adsorption data were well described by a pseudo-second-order model, with an adsorption activation energy of 42.602 kJ mol -1 , further predicting an SDS chemisorption uptake process by the precipitate. SDS could be considered as one of the most efficient flotation agents for the removal of vat dark blue BO in DAF processing.

  6. Quality of Life with Flotation Therapy for a Person Diagnosed with Attention Deficit Disorder, Atypical Autism, PTSD, Anxiety and Depression

    OpenAIRE

    Kjellgren, Anette; Edebol, Hanna; Nordén, Tommy; Norlander, Torsten

    2013-01-01

    The aim of this single-subject study was to report experiences from one and a half years of regular floating as described by a person with neuropsychiatric and mental health disorders. Floating, or Flotation Restricted Environmental Stimulation Technique, involves relaxation and sensory deprivation by means of resting in a tank with highly salted and body-tempered water. The subject, a 24-year-old woman diagnosed with attention deficit hyperactivity disorder, atypical autism, post-traumatic s...

  7. Solvent extraction of Cu, Mo, V, and U from leach solutions of copper ore and flotation tailings

    OpenAIRE

    Smolinski, Tomasz; Wawszczak, Danuta; Deptula, Andrzej; Lada, Wieslawa; Olczak, Tadeusz; Rogowski, Marcin; Pyszynska, Marta; Chmielewski, Andrzej Grzegorz

    2017-01-01

    Flotation tailings from copper production are deposits of copper and other valuable metals, such as Mo, V and U. New hydrometallurgical technologies are more economical and open up new possibilities for metal recovery. This work presents results of the study on the extraction of copper by mixed extractant consisting p-toluidine dissolved in toluene. The possibility of simultaneous liquid–liquid extraction of molybdenum and vanadium was examined. D2EHPA solutions was used as extractant, and re...

  8. Implementation of reverse flotation method to reduce reactive and non-reactive silica in bauxite ore from West Kalimantan

    Science.gov (United States)

    Wulandari, Winny; Purwasasmita, Mubiar; Sanwani, Edy; Pixelina, Adinda Asri; Maulidan, Agus

    2017-01-01

    This paper reports a study that implements reverse flotation method to separate silica from West Kalimantan bauxite ores. The study is aimed to find the good process condition to obtain low-silica bauxite as the feed for the Bayer process. The experiments were carried out in a 1 L of flotation cell tank. Dodecylamine was used as the collector, starch as the depressant, and MIBC as the frother. The varied parameters were solid content to solution (15-30% w/w), and pH (6 - 10). The results of XRF of products show that in all reverse flotation experiments, the ratio of alumina to silica (Al/Si) are increased from 7 up to 14. The increase of solid percentage in the flotation gives a good result for Al/Si ratio as well as alumina and silica recovery in concentrate, with 30% w/w solid percentage to solution increases Al/Si ratio to 14.38, with silica recovery of 20%. The good separation with variation of depressants is obtained with depressant concentration of 400 g/ton bauxite, with Al/Si ratio in concentrate 15 and ratio in tailing 7. For the pH variation, the good condition is obtained at pH 8, while for collector concentration, the good condition is obtained at 200 g/ton bauxite. XRD analysis of the feed indicates that bauxite ore consists of gibbsite, diaspore, kaolinite, halloysite, quartz, boehmite, hematite and rutile. It is found that the concentrate has similar minerals, but halloysite became very minor or classified as a trace.

  9. Ionic flotation of complexing oxyanions. Thermodynamics of uranyl complexation in a sulfuric medium. Definition of selectivity conditions of the process

    International Nuclear Information System (INIS)

    Bouzat, G.

    1987-01-01

    Oxyanion ionic flotation process with dodecylamine hydrochloride as collector is studied by investigation of flotation and filtration recovery curves, suspension turbidity, conductimetric measurements, and solubility of ionic species. The process is controlled by chemical reactions of precipitation and by adsorption of surfactant confering hydrophobic or hydrophilic surface properties to the solid phase respectively when one or two monolayers of surfactant are successively adsorbed. Equilibrium constants (in terms of activity) of the uranium (VI) complexation with sulphate oxyanions are calculated through Raman spectroscopic study of uranyl sulphate aqueous solutions. The complexation results in a shift of the symmetrical stretching vibration band of U0 2 to low wavenumbers and an increase of their cross section. The solubility curves of ionic species in the precipitation of uranyl -sulphate complexes by dodecylamine hydrochloride are modelled. The knowledge of solubility products, activity coefficients of the species and critical micellar concentration of the surfactant allow the modelling of flotation recovery curves. Temperature and collector structure modifications are studied in terms of optimization parameters and uranium extraction of mine drainage water is processed. Residual concentration of surfactant is considerably lowered by adsorption on montmorillonite

  10. Increasing the Fine Flaky Graphite Recovery in Flotation via a Combined MultipleTreatments Technique of Middlings

    Directory of Open Access Journals (Sweden)

    Weijun Peng

    2017-11-01

    Full Text Available As the residual flaky graphite ores become miscellaneous and fine, a single treatment technique for the middlings from the flotation process of graphite ore cannot efficiently recover the valuable graphite in the multistage grinding-flotation technology. In the study, the existence form of graphite and relationship of graphite with the associated gangue minerals were estimated by optical microscope analysis. The results indicated that the fine flaky graphite particles embedded with gangue minerals like a honeycomb, making it difficult to be beneficiated using the typical flotation technique. A combination technique of individual process and concentrated returning for the treatment of middlings was used to increase the graphite recovery based on the co-existing relationship between graphite and gangue minerals in the middlings. The graphite recovery of the final concentrate upgraded from 51.81% to 91.14% at a fixed carbon (FC content of 92.01% by a beneficiation process consisted of once coarse (94.41% passing 74 μm and rougher, five stages regrinding and six stages cleaning. The proposed treatment technique for middlings is of great significance to increase the recovery of fine flaky graphite.

  11. Surface treatment with Fenton for separation of acrylonitrile-butadiene-styrene and polyvinylchloride waste plastics by flotation.

    Science.gov (United States)

    Wang, Jian-Chao; Wang, Hui; Huang, Luo-Luo; Wang, Chong-Qing

    2017-09-01

    Surface treatment with Fenton was applied to flotation separation of acrylonitrile-butadienestyrene (ABS) and polyvinylchloride (PVC). After treatment, the floatability of ABS has a dramatic decrease, while the floatability of PVC is not affected. Fourier transform infrared spectroscopy (FT-IR) spectra and X-ray photoelectron spectroscopy (XPS) spectra were recorded to ascertain the mechanism of Fenton treatment. FT-IR and XPS analysis confirms that the introduction of oxygen-containing group occurs on the surface of ABS. The optimum conditions are molar ration (H 2 O 2 :Fe 2+ ) 10000, H 2 O 2 concentration 0.4M/L, pH 5.8, treatment time 2min and temperature 25°C, frother concentration 15mg/L and flotation time 3min. Particle sizes and mixing ratios were also investigated. Plastic mixtures of ABS and PVC with different particle sizes and mixing ratios can be effectively separated. The purity of ABS and PVC are up to 100% and 99.78%, respectively; the recovery of ABS and PVC are up to 99.89% and 100%, respectively. A practical, environmentally friendly and effective reagent, namely Fenton, was originally applied to surface treatment of ABS and PVC waste plastics for flotation separation of their mixtures. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. A Survey of Intestinal Parasites of Domestic Dogs in Central Queensland

    Directory of Open Access Journals (Sweden)

    Simone Gillespie

    2017-11-01

    Full Text Available Australia has a very high rate of dog ownership, which in some circumstances may lead to exposure to zoonotic parasitic diseases from those companion animals. Domestic dog faecal samples (n = 300 were collected from public spaces and private property in the greater Rockhampton (Central Queensland region and tested for intestinal helminths and protozoa by direct microscopy, two flotation methods and a modified acid-fast stain for cryptosporidia. Intestinal parasites detected included hookworms (25%, Cystoisospora ohioensis complex (9%, Blastocystis hominis (3%, Giardia duodenalis (3%, Spirometra erinacei (1% and Toxocara canis (1%, Sarcocystis spp. (2%, Cryptosporidium spp. (2% and Cystoisospora canis (1%. One infection each with Trichuris vulpis, Dipylidium caninum and a protozoa belonging to the Entamoeba histolytica complex were identified. Sheather’s sucrose centrifugal flotation was more sensitive than saturated salt passive flotation, but no single test detected all cases of parasitic infection identified. The test methodologies employed are poor at recovering larva of Strongyloides stercoralis, Aleurostrongylus abstrussis and eggs of cestodes such as Echinococcus granulosis, so the potential presence of these parasites in Central Queensland domestic dogs cannot be excluded by this survey alone.

  13. Dissolved air flotation primary clarifier improves performance of biological waste treatment at a latex manufacturing facility

    Energy Technology Data Exchange (ETDEWEB)

    Miller, D.R.; Kerecz, B.J.; Davis, M.N.

    1996-12-31

    Air Products and Chemicals, Inc. operates a chemical manufacturing facility in Piedmont, SC which generates a high strength COD emulsion wastewater from latex manufacturing. The on-site wastewater treatment facility consisted of flow equalization, activated sludge treatment and gravity clarification. The inability of the biological system to assimilate the high strength emulsion wastwater loadings led to incomplete conversion within the activated sludge process and poor settling waste sludge with turbid final effluent high in COD, BOD and TSS. The facility installed a dissolved air flotation (DAF) clarifier to effectively remove greater than 99 percent of the wastewater emulsion solids ahead of the activated sludge system. An organic coagulant is used for emulsion destabilization instead of iron or aluminum metal coagulants, improving DAF clarifier performance and minimizing operational cost and system complexity. An innovative DAF float solids collection and handling system produces disposal solids concentrations of 50 - 60% total solids resulting in further waste disposal cost savings. By removing more than 99 percent of the emulsion solids with the DAF clarifier ahead of the activated sludge process, the waste-water treatment facility now consistently produces a high quality effluent low in COD, BOD, TSS and turbidity. Wastewater treatment performance improved dramatically, as evident by the facility receiving the Western Carolina Regional Sewer Authority`s {open_quotes}Best Pollution Prevention Program{close_quotes} award. In addition, the wastewater treatment facility can now process three times the pre-DAF waste loads.

  14. Zeta potential of Polish copper-bearing shale in the absence and presence of flotation frothers

    Directory of Open Access Journals (Sweden)

    Mengsu Peng

    2014-09-01

    Full Text Available In this paper, zeta potential as a function of pH of copper-bearing shale, which is mined in Poland by KGHM, was investigated. The measurements were conducted in water and aqueous solutions of selected flotation frothers. It was established that for investigated copper-bearing shale, after dispersion in water, the isoelectric point (IEP occurs at pH=3.5. Addition of frothers decreased the IEP on the pH scale and the IEP for butanol was 1.93, for MIBC 2.90 and for eicosaethylene glycol hexadecyl ether (C16E20 2.76. In the case of introducing frothers changed, the zeta potential becomes less negative. An empirical equation, having two adjustable parameters, was used in the paper to approximate the course of the zeta potential-pH curve. The equation showed a very good approximation of the zeta potential of the investigated shale either in water or frother aqueous solutions.

  15. Separation of copper flotation concentrates into density fractions by means of polytungstate aqueous solution

    Directory of Open Access Journals (Sweden)

    Luszczkiewicz Andrzej

    2016-01-01

    Full Text Available Industrial and laboratory flotation copper concentrates were subjected to separation into density fractions by means of heavy liquids in the form of sodium polytungstate aqueous solutions. For two samples, three densities factions were created, however in different density ranges. The density fractions were analyzed to establish the content of copper, lead, silver and organic carbon. The size of particles in both samples was similar (90-95% −0.071 mm. It was found that the lightest density fractions −2.45 and −2.0 g/cm3 still contained sulfide minerals scattered in the organic carbon bearing particles. Removal of the lightest density fraction (−2.0 g/cm3 from the industrial concentrate samples led to considerable reduction of organic carbon (92% and increasing its quality from 13 to 28% Cu. The mineralogical analysis of the heavy liquid separation products showed that most sulfide minerals were evenly dissemination in the heaviest density fractions with the recovery of 95-98%. The lightest density fraction of −2.0 g/cm3, being the richest in organic carbon, contained approximately 3% of unliberated sulfide minerals.

  16. Compliance with an Ordinance Requiring the Use of Personal Flotation Devices by Children in Public Waterways

    Directory of Open Access Journals (Sweden)

    Garen J. Wintemute

    2013-03-01

    Full Text Available Introduction: For children ages 1-14, 21.6% of drowning cases involve swimming, wading, orplaying in natural bodies of water, such as rivers and lakes. Personal flotation devices (PFDs arebelieved to be an effective prevention measure. We measure compliance with city and countyordinances, publicized but not actively enforced, requiring that PFDs be worn by children accessingpublic bodies of water in Sacramento County, California.Methods: During June-August 2010, volunteers conducted 79 observation sessions at threepopular local river beaches where PFDs were available for use at no cost. They recorded personalcharacteristics and PFD use for 1,727 children in or very near the water and believed to be 0-13years of age (the age covered by the ordinances. We used logistic regression to quantify differencesin use by subject characteristics and study site.Results: The prevalence of PFD use was 29.9% overall, with large and significant differencesby age: < 1, 55.6%; 1-4, 37.6%; 5-10, 29.4%; 10-13, 14.6%; P < 0.0001. Usage did not varysignificantly by sex or race/ethnicity, and was somewhat higher at one study site (33.1% than at theothers (25.9% and 27.3%, P = 0.009.Conclusion: The combination of a statutory requirement and a cost-elimination strategy wasassociated with moderate rates of PFD use that were highest among young children.

  17. Development of a flotation-spectrophotometric method for determination of cetylpyridinium chloride in pharmaceutical products

    Directory of Open Access Journals (Sweden)

    Hooshang Parham

    2011-01-01

    Full Text Available A new simple and sensitive flotation-spectrophotometric method for the determination of cetylpyridinium chloride (CPC is reported. The method is based on the formation of an ion- associate between CPC and Orange II (OR which is floated in the interface of aqueous phase and n-hexane by vigorous shaking. The aqueous solution was discarded and the adsorbed ion associate on to the wall of a separating funnel was dissolved in a small volume of methanol solvent and its absorbance was measured at 480 nm. The apparent molar absorptivity (Ε of the ion associate was determined to be 4.12 x 10(5 L mol-1 cm-1. The calibration graph was linear in the concentration range of 15-800 ng mL-1 of CPC with a correlation coefficient of 0.9988. The limit of detection (LOD was 10.8 ng mL-1. The relative standard deviation (RSD for determination of 100 and 800 ng mL-1 of CPC was 3.47 and 2.04% (n=7, respectively. The method was successfully applied to the determination of CPC in a commercial mouth washer product.

  18. Selective Attachment of Leptospirillum ferrooxidans for Separation of Chalcopyrite and Pyrite through Bio-Flotation

    Directory of Open Access Journals (Sweden)

    Belinda Bleeze

    2018-02-01

    Full Text Available The replacement of depressants used in sulfide mineral beneficiation, with bacteria and their metabolites, promises to reduce the environmental impact left by the mining industry. In this study, the attachment of Leptospirillum ferrooxidans, L.f, to chalcopyrite and pyrite was investigated through Scanning Electron Microscopy (SEM. The impact of selective attachment, bacterial growth conditions, and extracellular polymeric substances (EPS was investigated through bio-flotation. L.f exhibits selective attachment to pyrite between 0 h and 168 h exposure via an indirect contact mechanism. Separation of chalcopyrite from pyrite was achieved through exposing the minerals for 72 h with an L.f culture grown on either HH media, chalcopyrite, or pyrite. The results produced 80.4, 43.4, and 47.4% recovery of chalcopyrite, respectively. However, EPS supernatant extracted from L.f grown on chalcopyrite, conditioned for 48 h, provided the best separation efficiency by the selective depression of pyrite resulting in 95.8% Cu recovery. Polysaccharide-rich EPS selectively attaches to pyrite within 48 h, depressing its floatability and ensuring successful separation with a PIPX collector.

  19. Effectiveness of sodium silicate as gangue depressants in iron ore slimes flotation

    Science.gov (United States)

    Rao, Danda Srinivas; Vijayakumar, Tadiparthi Venkata; Rao, Sripada Subba; Prabhakar, Swarna; Raju, Guntamadugu Bhaskar

    2011-10-01

    The recovery of iron from the screw classifier overflow slimes by direct flotation was studied. The relative effectiveness of sodium silicates with different silica-to-soda mole ratios as depressants for silica and silicate bearing minerals was investigated. Silica-to-soda mole ratio and silicate dosage were found to have significant effect on the separation efficiency. The results show that an increase of Fe content in the concentrate is observed with concomitant reduction in SiO2 and Al2O3 levels when a particular type of sodium silicate at a proper dosage is used. The concentrate of 58.89wt% Fe, 4.68wt% SiO2, and 5.28wt% Al2O3 with the weight recovery of 38.74% and the metal recovery of 41.13% can be obtained from the iron ore slimes with 54.44wt% Fe, 6.72wt% SiO2, and 6.80wt% Al2O3, when Na2SiO3 with a silica-to-soda mole ratio of 2.19 is used as a depressant at a feed rate of 0.2 kg/t.

  20. Compliance with an ordinance requiring the use of personal flotation devices by children in public waterways.

    Science.gov (United States)

    Wintemute, Garen J; Anton, Amy; Andrada, Emily; Ribeira, Ryan

    2013-03-01

    For children ages 1-14, 21.6% of drowning cases involve swimming, wading, or playing in natural bodies of water, such as rivers and lakes. Personal flotation devices (PFDs) are believed to be an effective prevention measure. We measure compliance with city and county ordinances, publicized but not actively enforced, requiring that PFDs be worn by children accessing public bodies of water in Sacramento County, California. During June-August 2010, volunteers conducted 79 observation sessions at three popular local river beaches where PFDs were available for use at no cost. They recorded personal characteristics and PFD use for 1,727 children in or very near the water and believed to be 0-13 years of age (the age covered by the ordinances). We used logistic regression to quantify differences in use by subject characteristics and study site. The prevalence of PFD use was 29.9% overall, with large and significant differences by age: Usage did not vary significantly by sex or race/ethnicity, and was somewhat higher at one study site (33.1%) than at the others (25.9% and 27.3%), P = 0.009. The combination of a statutory requirement and a cost-elimination strategy was associated with moderate rates of PFD use that were highest among young children.

  1. Factors affecting degradation of polyethylene terephthalate (PET) during pre-flotation conditioning

    International Nuclear Information System (INIS)

    Caparanga, Alvin R.; Basilia, Blessie A.; Dagbay, Kevin B.; Salvacion, Jonathan W.L.

    2009-01-01

    In general, plastics are exposed to different degrading agents in every procedure involved in their recovery from waste mixture and from subsequent recycling. In this study, two methods of pre-flotation conditioning were used to determine how these methods affect the general properties of the pre-conditioned PET particles to be recovered from the PET-PVC mixture. The first method comprised the conditioning of PET samples using an alkaline solution of nonionic surfactant (Triton X-100) based on the patent by the Goodyear Tire and Rubber Company. The second method, developed in this study, was a conditioning process which used an alkali-less solution of the same nonionic surfactant (Triton X-100) used in the first method. The following analytical methods were used to characterize properties of the pre-conditioned PET samples that were correlated to relative degradation of the samples: differential scanning calorimetry (DSC), for thermal behavior of the samples; FT-IR spectroscopy, for functional groups present in the samples; and, Pohl's method, for carboxyl end-group concentration count. Results show that in addition to water the presence of NaOH in the conditioning solution contributes to the further degradation of the polymer.

  2. Simultaneous Removal of Turbidity and Humic Acid Using Electrocoagulation/Flotation Process in Aqua Solution

    Directory of Open Access Journals (Sweden)

    Abdolmotaleb Seid-Mohammadi

    2015-06-01

    Full Text Available In this study, the applicability of the Electrocoagulation/Flotation (ECF process in batch operation was investigated for the simultaneous removal of turbidity and Humic acid (HA using Fe and Al electrodes. The effects of solution pH (3 - 12, electrical potentials (10 - 30 V, initial turbidity concentration (300 - 1200 NTU, and reaction time (10 - 30 minutes with or without HA were investigated in an attempt to achieve higher turbidity removal efficiency. The batch experimental results revealed that with initial turbidity of 300 NTU, at voltage of 30 V, after 30 minutes reaction times, and at pH values of 6 and 8, the ECF process for Fe and Al electrodes removed over 97% and 88% of turbidity, respectively. The percentage of turbidity removal from solution dropped with a decrease in voltages for both electrodes. The results displayed that the Fe-Fe electrode arrangement attained the highest performance for turbidity removal rate. As a result, ECF process was shown to be a very efficient, cost-effective, and promising process for efficient treatment of high turbid water. Regarding HA, the results showed that in ECF process over 67% and 43% of UV254 has been removed for Al and Fe electrodes, respectively at the optimum pH, 30 minutes reaction time and 30 V applied voltage. Thus, it can be considered that Fe and Al are the best electrodes for removing turbidity and HA, respectively.

  3. Researching the technology of tar removal from coke-chemical plants’ wastewater by reagent flotation method

    Directory of Open Access Journals (Sweden)

    Anna V. Ivanchenko

    2015-03-01

    Full Text Available The study aims to identify process patterns of tars and oils removal from phenolic wastewater by reagent flotation with bringing those components’ content to acceptable concentrations. For the first time established is the effect of Al2(SO43, AlCl3, FeSO4, Fe2(SO43, Al2(OH5Cl and FeCl3 doses onto residual tar content in phenolic wastewater. Results obtained give the possibility to prevent air pollution resulting from the toxic substances emission at the wet quenching with water containing excessive oils and to increase the quality of wastewater biological treatment. It is shown experimentally that the most efficient are Fe2(SO43, FeCl3 and Al2(OH5Cl at optimum concentrations of 50, 30 and 30 mg/dm3 respectively. The Al2(OH5Cl can be recommended for implementation at industry on existing coking plants and municipal wastewater treatment plants to improve the environmental air and water resources condition in Ukraine.

  4. Optimizing the Air Dissolution Parameters in an Unpacked Dissolved Air Flotation System

    Directory of Open Access Journals (Sweden)

    Adam Dassey

    2011-12-01

    Full Text Available Due to the various parameters that influence air solubility and microbubble production in dissolved air flotation (DAF, a multitude of values that cover a large range for these parameters are suggested for field systems. An unpacked saturator and an air quantification unit were designed to specify the effects of power, pressure, temperature, hydraulic retention time, and air flow on the DAF performance. It was determined that a pressure of 621 kPa, hydraulic retention time of 18.2 min, and air flow of 8.5 L/h would be the best controlled parameters for maximum efficiency in this unit. A temperature of 7 °C showed the greatest microbubble production, but temperature control would not be expected in actual application. The maximum microbubble flow from the designed system produced 30 mL of air (±1.5 per L of water under these conditions with immediate startup. The maximum theoretical dissolved air volume of 107 mL (±6 was achieved at a retention time of 2 h and a pressure of 621 kPa. To isolate and have better control over the various DAF operational parameters, the DAF unit was operated without the unsaturated flow stream. This mode of operation led to the formation of large bubbles at peak bubble production rates. In a real-world application, the large bubble formation will be avoided by mixing with raw unsaturated stream and by altering the location of dissolved air output flow.

  5. Performance optimization of biological waste treatment by flotation clarification at a chemical manufacturing facility

    Energy Technology Data Exchange (ETDEWEB)

    Kerecz, B.J. [Air Products and Chemicals, Inc., Allentown, PA (United States); Miller, D.R. [Komline-Sanderson, Peapack, NJ (United States)

    1995-12-31

    Air Products and Chemicals, Inc., utilizes a deep-tank activated sludge wastewater treatment system with a dissolved air flotation clarifier (DAF) to effectively treat amine wastes containing residual organics, ammonia-nitrogen and organic nitrogen. The bio-system, a deep tank aeration system, produces a high quality final effluent low in biochemical oxygen demand (BOD), ammonia and organic nitrogen, turbidity and total suspended solids. Prior to installing the DAF, treatment performance was at risk with a gravity clarifier. Waste treatment performance was jeopardized by poor settling bio-flocs and uncontrollable solids-liquid separation problems within the gravity clarifier. The solids settleability problems resulted primarily from mixed liquor nitrogen supersaturation degassing in the clarifier. As a result of the degassing, biomass floated on the gravity clarifier or overflowed the effluent weir. As a result of biomass loss periodically organic carbon and total Kjeldahl nitrogen loadings had to be reduced in order to maintain optimal food-to-mass ratios. As biomass levels dropped within the aeration basin, waste treatment performance was at risk and waste loads had to be decreased causing waste inventories to increase in storage tanks.

  6. Flotation Bubble Delineation Based on Harris Corner Detection and Local Gray Value Minima

    Directory of Open Access Journals (Sweden)

    Weixing Wang

    2015-03-01

    Full Text Available Froth image segmentation is an important and basic part in an online froth monitoring system in mineral processing. The fast and accurate bubble delineation in a froth image is significant for the subsequent froth surface characterization. This paper proposes a froth image segmentation method combining image classification and image segmentation. In the method, an improved Harris corner detection algorithm is applied to classify froth images first. Then, for each class, the images are segmented by automatically choosing the corresponding parameters for identifying bubble edge points through extracting the local gray value minima. Finally, on the basis of the edge points, the bubbles are delineated by using a number of post-processing functions. Compared with the widely used Watershed algorithm and others for a number of lead zinc froth images in a flotation plant, the new method (algorithm can alleviate the over-segmentation problem effectively. The experimental results show that the new method can produce good bubble delineation results automatically. In addition, its processing speed can also meet the online measurement requirements.

  7. Optimal conditions for particle-bubble attachment in flotation: an experimental study

    Science.gov (United States)

    Sanchez Yanez, Aaron; Hernandez Sanchez, Jose Federico; Thoroddsen, Sigurdur T.

    2017-11-01

    Mineral flotation is a process used in the mining industry for separating solid particles of different sizes and densities. The separation is done by injecting bubbles into a slurry where the particles attach to them, forming floating aggregates. The attachment depends mainly on the bubbles and particles sizes as well as the hydrophobicity and roughness of the particles. We simplified the collective behavior in the industrial process to a single free particle-bubble collision, in contrast with previous studies where one of the two was kept fixed. We experimentally investigated the collision of spherical solid particles of a fixed diameter with bubbles of different sizes. By controlling the initial relative offset of the bubble and the particle, we conducted experiments observing their interaction. Recording with two synchronized high-speed cameras, perpendicular to each other, we can reconstruct the tridimensional trajectories of the bubble, the solid particle, and the aggregate. We describe the conditions for which the attachment happens in terms of dimensionless parameters such as the Ohnesorge number, the relative particle-bubble offset and the hydrophobicity of the particle surface. We furthermore investigate the role of the surface roughness in the attachment.

  8. Enhancing organic matter removal in desalination pretreatment systems by application of dissolved air flotation

    DEFF Research Database (Denmark)

    Shutova, Yulia; Karna, Barun Lal; Hambly, Adam C.

    2016-01-01

    Membrane fouling in reverse osmosis (RO) systems caused by organic matter (OM) remains a significant operational issue during desalination. Dissolved air flotation (DAF) has recently received attention as a pre-treatment option for seawater OM removal; however, only a limited number of studies have...... been undertaken. This may be because it is difficult to characterise OM in seawater due to the high salt content and low carbon concentration. In this study, DAF pre-treatment experiments were conducted using a model seawater solution, and real seawater and brackish water samples. DAF performance...... on the sample, respectively. The optimal normalised coagulant dose (Fe3+ to DOC ratio) was observed to be 0.5-4 at pH5.5 increasing to 4-12 at pH7.5. At pH5.5, the optimum coagulant dose increased with increasing humic character of the feed water. Overall, the OM removal efficiency by DAF observed in this study...

  9. Comparison of Adsorption of Phenol O-O and N-O Chelating Collectors at the Malachite/Water Interface in Flotation

    Directory of Open Access Journals (Sweden)

    Zhili Li

    2017-02-01

    Full Text Available To separate one base metal mineral from another by flotation, it is indispensable to identify chemical reagents that specifically interact with the surface metal sites of one mineral or a group of minerals. This work studies the interactions of chelating collectors which offer the best potential for collecting abilities and mineral specificity with a typical refractory oxide mineral (malachite. Zeta potential, adsorption and Fourier transform infrared (FTIR measurements are applied to differentiate the interactions of salicylaldoxime and salicyl hydroxamate on the malachite surface. Salicylaldoxime and salicyl hydroxamate are of molecular structures that resemble each other, but with different bond distances in the ligand atoms which result in their unusual adsorption behavior and collecting ability. Thus, the flotation of malachite behaves differently with the two chelating collectors. This study might provide useful clues for designing novel collectors in base metal oxide flotations.

  10. Combining ZnO/microwave treatment for changing wettability of WEEE styrene plastics (ABS and HIPS) and their selective separation by froth flotation

    Science.gov (United States)

    Thanh Truc, Nguyen Thi; Lee, Byeong-Kyu

    2017-10-01

    This study reports a simple froth flotation method to separate plastic wastes of acrylonitrile-butadiene-styrene (ABS) and high impact polystyrene (HIPS) after initial hydrophilization by coating the plastics with ZnO and microwave treatment. ABS and HIPS are typical styrene-based WEEE plastics having similar density and hydrophobicity, which hinders their separation for recycling. After coating with ZnO, 2-min microwave treatment rearranged the ABS surface and thus changed its molecular mobility and increased its hydrophilicity. The combined ZnO coating/microwave treatment facilitated the selective separation of ABS and HIPS with 100% and 95.2% recovery and 95.4% and 100% purity in froth flotation, respectively. The combination of ZnO coating-microwave treatment and froth flotation can be utilized as a selective ABS/HIPS separation technique for improved recycling of WEEE plastics.

  11. Utilization of ash from the Bor thermal power plant as a pH regulating agent in copper ore flotation plants

    Energy Technology Data Exchange (ETDEWEB)

    Stanojlovic, R.; Budic, I.; Knezevic, M.; Spasovski, B.; Radosevic, N.; Jovanovic, R.; Stanojlovic, D. (Tehnicki Fakultet, Bor (Yugoslavia))

    1987-02-01

    Highlights results of experiments carried out at the Bor Mining Faculty laboratories into the use of ash from the Bor thermal power plant as a pH regulating agent in the local copper flotation plant. Some 12,000 t of ash could be so used in place of lime, thereby saving 94 million dinar anually. In addition, ash disposal costs would decrease and environmental protection would be improved. Investigation details (ash analysis, flotation scheme, copper and pyrite yield coefficients of flotation process obtained using ash, lime, and a combination of the two) are presented in tables and illustrations. These investigations were successful; industrial use of ash as a pH regulator is expected to be profitable. 2 refs.

  12. X-PEEM, XPS and ToF-SIMS characterisation of xanthate induced chalcopyrite flotation: Effect of pulp potential

    Science.gov (United States)

    Kalegowda, Yogesh; Chan, Yuet-Loy; Wei, Der-Hsin; Harmer, Sarah L.

    2015-05-01

    Synchrotron-based X-ray photoemission electron microscopy (X-PEEM), X-ray photo-electron spectroscopy (XPS), time-of-flight secondary ion mass spectrometry (ToF-SIMS) and ultraviolet visible spectroscopy were used to characterize the flotation behaviour of chalcopyrite with xanthate at different processing conditions. The flotation recovery of chalcopyrite decreased from 97% under oxidative conditions (Eh ~ 385 mV SHE, pH 4) to 41% at a reductive potential of - 100 mV SHE (at pH 9). X-PEEM images constructed from the metal L3 absorption edges were used to produce near-edge X-ray absorption fine structure (NEXAFS) spectra from regions of interest, allowing the variability in mineral surface chemistry of each mineral particle to be analysed, and the effect of pulp potential (Eh) on the flotation of chalcopyrite to be determined. XPS, ToF-SIMS and NEXAFS analyses of chalcopyrite particles at oxidative conditions show that the surface was mildly oxidised and covered with adsorbed molecular CuEX. The Cu 2p XPS and Cu L2,3 NEXAFS spectra were dominated by CuI species attributed to bulk chalcopyrite and adsorbed CuEX. At a reductive potential of - 100 mV SHE, an increase in concentration of CuI and FeIII oxides and hydroxides was observed. X-PEEM analysis was able to show the presence of a low percentage of CuII oxides (CuO or Cu(OH)2) with predominantly CuI oxide (Cu2O) which is not evident in Cu 2p XPS spectra.

  13. Determination of Trace Amounts of Lead Using the Flotation-spectrophotometric method

    Directory of Open Access Journals (Sweden)

    Sabah Shiri

    2011-01-01

    Full Text Available The present study describes a simple and highly selective method for separation, preconcentration and spectrophotometric determination of extremely low concentrations of lead. It is based on flotation of a complex of Pb 2+ ions and Alizarin yellow between aqueous and n -hexane interface at pH = 6. The proposed procedure is also applied for determination of lead in both tap water and prepared sea water samples. Beer's Law was obeyed over the concentration range of 3.86 × 10 -8 To 8.20 × 10 -7 molL -1 (8-170 ngmL -1 with an apparent molar absorptivity of 1.33 × 10 6 molL -1 cm -1 for a 100 mL aliquot of the water sample. The detection limit (n = 10 was 8.7 × 10 -9 molL -1 (1.0 ngmL -1 and the Relative standard deviation (R.S.D, (n = 10 for 7.2 × 10 -7 molL -1 (150 ngmL -1 of Pb (II was 4.36%. A notable advantage of the method is that the determination of Pb (II is free from the interference of almost all cations and ions found in the environment and waste water samples. The determination of Pb (II in tap and synthetic seawater samples was also carried out by the present method. The results were satisfactorily comparable so that the applicability of the proposed method was confirmed to the real samples.

  14. Fe(II)-regulated moderate pre-oxidation of Microcystis aeruginosa and formation of size-controlled algae flocs for efficient flotation of algae cell and organic matter.

    Science.gov (United States)

    Qi, Jing; Lan, Huachun; Liu, Ruiping; Liu, Huijuan; Qu, Jiuhui

    2018-06-15

    The coagulation/flocculation/flotation (C/F/F) process is becoming a popular method for algae-laden water treatment. However, the efficiency of flotation is highly dependent on the ability of the preceding coagulation/flocculation process to form flocculated algae flocs. This study aims to improve the Microcystis aeruginosa flotation efficiency from algae cell and organic matter aspects by applying Fe(II)-regulated pretreatment enhanced Al coagulation process. The ability of the C/F/F process to remove cyanobacterial cells can be enhanced from 8% to 99% at a Fe(II) dose of 30 μM. The Al dose needed can be reduced by more than half while achieving successful flotation. The introduced Fe(II) after KMnO 4 can not only realize moderate pre-oxidation of cyanobacterial cells, but also form in-situ Fe(III). The DOC value can also be decreased significantly due to the formation of in-situ Fe(III), which is more efficient in dissolved organic matter (DOM) removal compared with pre-formed Fe(III). In addition, the gradually hydrolyzed in-situ Fe(III) can facilitate the hydrolysis of Al as a dual-coagulant and promote the clustering and cross-linking of Al hydrolyzates, which can enhance the formation of size-controlled algae flocs. Finally, the size-controlled algae flocs can be effectively floated by the bubbles released in the flotation process due to the efficient collision and attachment between flocs and bubbles. Therefore, the efficient flotation of algae cell and organic matter can be realized by the Fe(II) regulated moderate pre-oxidation of M. aeruginosa and formation of size-controlled algae flocs. Copyright © 2018 Elsevier Ltd. All rights reserved.

  15. Removal of wax and stickies from OCC by flotation. Progress report No. 2, April 1--June 30, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Doshi, M.R.; Dyer, J. [Doshi and Associates, Inc., Appleton, WI (United States); Heise, O. [Voith Sulzer Papertechnology, Appleton, WI (United States)

    1998-08-01

    During the second quarter of the study the authors examined the conditions necessary for repulping a mixture of wax-coated boards that would be conducive to the flotation of detached wax. Also important for the economic viability of a waxed-board repulping process is adequate defibering of the recovered paper. Several methods for the dewaxing of pulped waxed-boards were investigated. The authors have continued to survey the literature to determine what other efforts are being made to ameliorate the impact of waxed boards during the recycling of OCC.

  16. THERMOLYSIS OF FOAM PRODUCTS FORMED AT THE FLOTATION EXTRACTION OF COPPER AND NICKEL IONS BY HELP OF WAX PEAT

    Directory of Open Access Journals (Sweden)

    V. F. Sazonova

    2015-02-01

    Full Text Available There thermogravimetric study of foam product at the flotation extraction of cop­per and nickel ions by wax peat results are described. It shown that oxidizing roasting of foam products (i.e. hydrated soaps of polyvalent metals proceeds in several steps. At the first step (t<100 °С dehydration takes place. At the next ones (t=160^665 °С The thermic destruction and burning of organic compounds occurs. The residue is the of metal oxides.

  17. APLICATION OF FLOTATION PNEUMATC CELLS IN IRON ORE CONCENTRATION PROCESS AT SAMARCO MINERAÇÃO S.A.

    Directory of Open Access Journals (Sweden)

    Alexandro Uliana

    2013-12-01

    Full Text Available The Samarco Mineração, located between the cities of Mariana and Ouro Preto (MG, Brazil, has been studying alternatives and/or more efficient equipments for their unit operations of Iron Ore Concentration Plants – such as the flotation pneumatic cells. With the following advantages: higher productivity, no moving parts, lower retention time and generating smaller bubbles. Pilot scale tests were performed at L.C.P (Laboratório de Controle de Processo - Laboratory Process Control, a laboratory of Samarco. It was used the same samples that it is used in the mechanical flotation process – Wemco cells – in Concentrator I (CI for these tests. The goals to be achieved with the essays were: quartz content in the concentrate below 4% in terms of iron content in the tailings below 10% - data normally obtained in industrial scale in the stages rougher, cleaner, recleaner and scavenger – CI. For the pilot-scale pneumatic cell, the best result achieved was: 2,52% of quartz in the concentrate and 12,67% of iron in the tailing. This indicates that, after optimization, the desired especifications can be achieved.

  18. Latest generation flotation in applications with industrial waste waters; Flotacion de ultima generacion en aplicaciones con aguas industriales

    Energy Technology Data Exchange (ETDEWEB)

    Galdi, M.; Azzollini, G.

    2004-07-01

    The article provides an introduction to the historical development of water flotation equipment. Its earliest application was in paper-making factories where it was used to recover cellulose fibres. As it was improved, it was employed to treat waste waters with hydraulic loads of 4,8 m''3/m''2+h. Further improvements gave it a circular shape with the flocculation in the middle and a highly controlled radial flow and the speed increased to 5.4 m''3/m''2*/h. Recently, Ecomac, a flotation system whose performance is close to the ideal. has been developed. In this system the fluid is immobile, as the advanced design of the internal conduits eliminates turbulence by distributing the liquid right across the annular section of the tank and feeds compartments of decreasing cross sections. This arrangement allows it to cope with hydraulic loads of 8.4 m''3/m''2*h. Practical performance results obtained in the mechanical,food (yoghurt, preserves, wine) and textile dyeing industries are given. (Author)

  19. Separating dolomite from phosphate rock by reactive flotation: Fundamentals and application

    Science.gov (United States)

    El-Midany, Ayman A.

    Florida is currently one of the largest phosphate producers in the world. Unfortunately, the phosphate industry in Florida is suffering from depletion of the phosphate-rich ore. Dolomite, however, is a major impurity in the ores. The presence of MgO, in dolomite, can cause several problems during production of phosphoric acid and final fertilizers. Efforts to solve the dolomite problem have been reported by several researchers throughout the world. Yet, only heavy media separation process has been applied commercially. However, the process was discontinued because of its low separation efficiency in terms of grade and recovery. In this study, we tested an innovative idea based on simple fact that dolomite, as a carbonate mineral, generates CO2 when exposed to a slightly acidic solution, capturing CO2 bubbles at dolomite particle surface can selectively float the dolomite and separate it from phosphate. Formation of such bubbles requires a surface-active agent(s) at solution/dolomite interface. Preliminary tests indicated that polyvinyl alcohol (PVA) could serve this function. This process is called the Reactive Flotation, RF. To develop this process and to scale it up for industrial use, we conducted fundamental and applied research studies. Among these studies were optimizing of RF process by investigating the factors affecting the process (including bench and pilot scale tests) using statistical experimental designs. It was found that the acid concentration, PVA concentration, and particle size are the main factors. The optimum conditions were determined and applied to usage in a gravity separation device, (i.e., a sluice). Using such a device, a concentrate contains 0.65% MgO with >94 MgO % removal can be achieved. In addition, fundamental studies revealed that the hydrogen bonding is the adsorption mechanism confirmed by adsorption isotherm of PVA on dolomite and phosphate, adhesion of PVA to dolomite surface (using contact angle and surface tension), Fourier

  20. Obtention of high purity silica from the flotation waste of itabiritic ore

    International Nuclear Information System (INIS)

    Martins, Polyana Fabricia Fernandes

    2016-01-01

    Banded iron formations are exploited as iron mineral in 'Quadrilatero Ferrifero' of Minas Gerais (MG) State, Brazil. About half of the amount of extracted material becomes tailings, which are stored in tailing dams or used for filling mining pits. Tens of thousands of tons are generated daily in operating mines in this region, causing concern about the environmental liabilities, and costs to manage the tailing dams. Miners are committed to finding uses for these wastes in other productive chains. This thesis aimed to obtain high purity silica from the flotation tailings of banded iron formations using classical techniques for ore processing, such as particle size classification and magnetic separation, followed by hydrometallurgical leaching, also alkaline fusion and chemical precipitation. The tailings samples was collected in the tailings dam of Peak Mine operated by Vale A.S., in Itabirito – MG. This sample had initially 33.4% by weight SiO 2 , 57.4% wt Fe 2 O 3 and 8.31% wt Al 2 O 3 . After desliming for disposal of the fine particles (-37μm) the composition was 68.0% SiO 2 , 31.4% Fe 2 O 3 and 0.50% Al 2 O 3 . After magnetic separation, the composition was 93.8% SiO 2 , 1.16% Fe 2 O 3 and 3.80% Al 2 O 3 . After acid leaching l or digestion to remove impurities, it was possible to obtain silica with 98% purity. The fusion with sodium hydroxide, followed by alkaline leaching of sodium silicate and silica precipitation gave purities of about 99.5%. Values even higher may be possible with optimization of the parameters of alkaline fusion or by repeating the process from the product with purity of 99.5%. The iron oxide content and the aluminum main contaminants were 0.01% and 0.07%, respectively. Amorphous silica was obtained with high specific surface (322 m 2 /g) and particle size less than 200 nm. Depending on the application, a control should be made for the impurities, such as phosphorus, potassium and boron. (author)

  1. Simple fecal flotation is a superior alternative to guadruple Kato Katz smear examination for the detection of hookworm eggs in human stool

    DEFF Research Database (Denmark)

    Inpankaew, Tawin; Schär, Fabian; Khieu, Virak

    2014-01-01

    parameters of the Kato-Katz (KK) and simple sodium nitrate flotation technique (SNF) in terms of detection and quantification of hookworm eggs, with PCR as an additional reference test in stool, collected as part of a baseline cross-sectional study in Cambodia. METHODS/PRINCIPLE FINDINGS: Fecal samples...

  2. A perspective of stepwise utilisation of Bayer red mud: Step two--Extracting and recovering Ti from Ti-enriched tailing with acid leaching and precipitate flotation.

    Science.gov (United States)

    Huang, Yanfang; Chai, Wencui; Han, Guihong; Wang, Wenjuan; Yang, Shuzhen; Liu, Jiongtian

    2016-04-15

    The extraction and recovery of Ti from Ti-enriched tailing with acid leaching and precipitate flotation, as one of the critical steps, was proposed for the stepwise utilization of red mud. The factors influencing acid leaching and precipitate flotation were examined by factorial design. The leaching thermodynamics, kinetics of Ti(4+), Al(3+) and Fe(3+), and the mechanism of selectively Fe(3+) removal using [Hbet][Tf2N] as precipitating reagent were discussed. The extracting of Ti(4+), Al(3+) and Fe(3+) in concentrated H2SO4 is controlled by diffusion reactions, depending mainly upon leaching time and temperature. The maximum extracting efficiency of Ti(4+) is approximately 92.3%, whereas Al(3+) and Fe(3+) leaching are respectively 75.8% and 84.2%. [Hbet][Tf2N], as a precipitating reagent, operates through a coordination mechanism in flotation. The pH value is the key factor influencing the flotation recovery of Ti(4+), whereas the dosage of precipitating reagent is that for Al(3+) recovery. The maximum flotation recovery of Ti(4+) is 92.7%, whereas the maximum Al(3+) recovery is 93.5%. The total recovery rate for extracting and recovering titanium is 85.5%. The liquor with Ti(4+) of 15.5g/L, Al(3+) of 30.4g/L and Fe(3+) of 0.48g/L was obtained for the following hydrolysis step in the integrated process for red mud utilisation. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Flotation and adherence characteristics of Toxocara canis and T. cati and a reliable method for recovering Toxocara eggs from soil.

    Science.gov (United States)

    Kleine, Annika; Janecek, Elisabeth; Waindok, Patrick; Strube, Christina

    2016-08-30

    Toxocara canis and T. cati are worldwide distributed intestinal nematodes of canids and felids and pose a threat to public health due to possible clinical manifestations in humans. Different methods for detection of Toxocara eggs in soil have been described, but conducted studies deal with egg recovery rates of T. canis or "Toxocara spp." only whereas T. cati egg recovery has not been taken into consideration. Thus, flotation properties in sodium chloride solution and adherence characteristics to different substrates possibly coming into contact with Toxocara eggs before or during purification from soil were evaluated for both, T. canis and T. cati eggs. No significant difference was observed in flotation characteristics, but comparison of adherence properties revealed significantly less adherence of T. cati eggs on almost all evaluated substrates ("sand", side sealed bags, glass beaker, centrifuge tube) and different washing solutions (tap water, Tween(®) 80, Triton™ X-100). Mean adhesion rates of T. cati eggs ranged from 15.9% to 68.9%, those of T. canis eggs from 28.3% to 83.9%. While adherence of T. cati eggs on any substrate was significantly reduced when rinsing with Tween(®) 80 solution, no effect on T. canis eggs could be observed. Generally, Toxocara eggs adhere better on plastic than on glass. Evaluation of a method including only non-hazardous substances for purification of Toxocara eggs from soil resulted in a statistically significant higher recovery rate of T. canis (42.6% recovered eggs) compared to T. cati eggs (30.9% recovered eggs). As these percentages are above average for described methods to recover Toxocara eggs from soil, the presented method is considered reliable for prevalence studies. Copyright © 2016 Elsevier B.V. All rights reserved.

  4. Removal of methylene blue from its aqueous solution by froth flotation: hydrophobic silica nanoparticle as a collector

    Energy Technology Data Exchange (ETDEWEB)

    Hu, Nan; Liu, Wei; Ding, Linlin; Wu, Zhaoliang, E-mail: zhaoliangwu-hebut@163.com; Yin, Hao; Huang, Di; Li, Hongzhen; Jin, Lixue; Zheng, Huijie [Hebei University of Technology, School of Chemical Engineering and Technology (China)

    2017-02-15

    Dye pollution has been a severe problem faced by worldwide environmentalists. The use of nanoparticles as adsorbents has attracted widespread interests for effectively removing dyes, while the separation of them from an aqueous solution is a difficult and important subject. For achieving the simultaneous removal of methylene blue (MB) and nanoadsorbents, this work utilized a commercial hydrophobic silica nanoparticle (SNP) (200.0 ± 10.0 nm in average particle size) as a collector and then developed a novel froth flotation technology without using any surfactants. Under the suitable conditions of anhydrous ethanol dosage of 8 mL, pH of 9.0, SNP concentration of 600 mg/L, and flotation column height of 600 mm, the removal efficiencies of MB and SNPs and the volume ratio reached 91.1 ± 4.6%, 93.9 ± 4.7%, and 10.5 ± 0.5, respectively. Subsequently, the recovered MB-adsorbed SNPs in the foamate were separated by free setting due to their high concentration and massive agglomeration. After free setting, MB could be effectively separated from the recovered MB-adsorbed SNPs by using ethanol at pH 2.0 and repeating five cycles of washing-centrifugation. Additionally, the regenerated SNPs could be reused for removing MB up to five times. Overall, this work had a significant meaning for the treatment of dye-contaminated wastewaters.

  5. Enhanced independence and quality of life through treatment with flotation-Restricted Environmental Stimulation Technique of a patient with both Attention Deficit Hyperactivity Disorder and Aspergers syndrome: a case report.

    Science.gov (United States)

    Edebol, Hanna; Kjellgren, Anette; Bood, Sven-Ake; Norlander, Torsten

    2009-07-07

    The objective of this qualitative case report was to describe experiences of flotation-Restricted Environmental Stimulation Technique from the perspective of a woman with Attention Deficit Hyperactivity Disorder, Aspergers syndrome and experiences of depression and distress. The respondent is a 36-year-old woman from Sweden, assessed and diagnosed by a neuropsychological multi-professional team in 2006. The 19-session flotation series prolonged during almost one year. The positive development of arousal control, activity regulation, sensory integration and interpretation, cognitive functioning and emotional maturity created experiences of personal independence and quality of life. Flotation-restrictive environmental stimulation technique was experienced as a meaningful treatment. Additional studies of treatment for Attention Deficit Hyperactivity Disorder and comorbid disorders in adults using the flotation-restrictive environmental stimulation technique are strongly encouraged.

  6. Kinetics of Cu (II) separation by ion flotation techniques, in cells with flexible spargers; Cinetica de separacion de Cu(II) por tecnicas de flotacion ionica, en celdas con dispersores flexibles

    Energy Technology Data Exchange (ETDEWEB)

    Reyes, M.; Tavera, F. J.; Escudero, R.; Patino, F.; Salinas, E.; Rivera, I.

    2010-07-01

    This research studies and experimentally determines the kinetic parameters and effect of modifying the hydrodynamics and chemical conditions of the air-liquid dispersions during the Cu (II) extraction by ion flotation techniques in cells with porous spargers. Results show that the elimination of Cu (II) from solution can be carried out by ion flotation in one stage, obtaining efficiencies of 68% and 56% for the flat and cylindrical sparger respectively with a xanthate concentration of 0,02 g/l. In multistage systems five cells, recoveries over 92 % were achieved for both sparger geometries. The behavior of the flotation apparent kinetic constant is linear to the parameters that characterize dispersion (Jg, eg y Db), until a point is achieved where the process instability makes the system inoperable. The results show that removing base metal ions by ion flotation is strongly affected by the following factors: collector concentration [C], Jg, eg, Db, Jl and Sb. (Author) 20 refs.

  7. American Association of Veterinary Parasitologists' review of veterinary fecal flotation methods and factors influencing their accuracy and use--is there really one best technique?

    Science.gov (United States)

    Ballweber, L R; Beugnet, F; Marchiondo, A A; Payne, P A

    2014-07-30

    The principle of fecal flotation is based on the ability of a solution to allow less dense material (including parasite elements) to rise to the top. However, there are numerous factors that will influence the accuracy and use of such a theoretically simple technique. Whether or not centrifugation is used appears to have an impact on the ability to detect some parasites, but not others. Using a flotation solution with a relatively high specific gravity favors the simultaneous flotation of the diagnostic stages of many different parasites while, at the same time, making recognition of some more difficult because of distortion as well as the amount of debris in the preparation. Dilution methods tend to be less accurate because they require extrapolation; however, they are quicker to perform, in part, because of the cleaner preparation. Timing is a critical factor in the success of all flotation methods, as is technical ability of the personnel involved. Thus, simplicity, low costs and time savings have generally favored gravitational flotation techniques (including the McMaster technique and its modifications). How accurate the method needs to be is dependent upon the purpose of its use and choice of method requires an understanding of analytical sensitivity and expected levels of egg excretion. In some instances where the difference between, for example, 0 and 50 eggs per gram is insignificant with regards to management decisions, less accurate methods will suffice. In others, where the presence of a parasite means treatment of the animal regardless of the numbers of eggs present, methods with higher analytical sensitivities will be required, particularly for those parasites that pass few eggs. For other uses, such as the Fecal Egg Count Reduction Test, accuracy may become critical. Therefore, even though recommendations for standardized fecal flotation procedures have been promoted in the past, it is clear that the factors are too numerous to allow for the

  8. A perspective of stepwise utilisation of Bayer red mud: Step two—Extracting and recovering Ti from Ti-enriched tailing with acid leaching and precipitate flotation

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Yanfang; Chai, Wencui; Han, Guihong, E-mail: guihong-han@hotmail.com; Wang, Wenjuan; Yang, Shuzhen; Liu, Jiongtian

    2016-04-15

    Highlights: • An integrated process for the stepwise disposal of red mud was proposed. • Extracting and recovering Ti from Ti-enriched tailing was the second step. • The factors influencing acid leaching and precipitate flotation were examined. • The extracting of metals in concentrated H{sub 2}SO{sub 4} was controlled by diffusion reactions. • [Hbet][Tf{sub 2}N] was an effective precipitating reagent with its coordination mechanism. - Abstract: The extraction and recovery of Ti from Ti-enriched tailing with acid leaching and precipitate flotation, as one of the critical steps, was proposed for the stepwise utilization of red mud. The factors influencing acid leaching and precipitate flotation were examined by factorial design. The leaching thermodynamics, kinetics of Ti{sup 4+}, Al{sup 3+} and Fe{sup 3+}, and the mechanism of selectively Fe{sup 3+} removal using [Hbet][Tf{sub 2}N] as precipitating reagent were discussed. The extracting of Ti{sup 4+}, Al{sup 3+} and Fe{sup 3+} in concentrated H{sub 2}SO{sub 4} is controlled by diffusion reactions, depending mainly upon leaching time and temperature. The maximum extracting efficiency of Ti{sup 4+} is approximately 92.3%, whereas Al{sup 3+} and Fe{sup 3+} leaching are respectively 75.8% and 84.2%. [Hbet][Tf{sub 2}N], as a precipitating reagent, operates through a coordination mechanism in flotation. The pH value is the key factor influencing the flotation recovery of Ti{sup 4+}, whereas the dosage of precipitating reagent is that for Al{sup 3+} recovery. The maximum flotation recovery of Ti{sup 4+} is 92.7%, whereas the maximum Al{sup 3+} recovery is 93.5%. The total recovery rate for extracting and recovering titanium is 85.5%. The liquor with Ti{sup 4+} of 15.5 g/L, Al{sup 3+} of 30.4 g/L and Fe{sup 3+} of 0.48 g/L was obtained for the following hydrolysis step in the integrated process for red mud utilisation.

  9. Feed-Forward Neural Network Soft-Sensor Modeling of Flotation Process Based on Particle Swarm Optimization and Gravitational Search Algorithm

    Directory of Open Access Journals (Sweden)

    Jie-Sheng Wang

    2015-01-01

    Full Text Available For predicting the key technology indicators (concentrate grade and tailings recovery rate of flotation process, a feed-forward neural network (FNN based soft-sensor model optimized by the hybrid algorithm combining particle swarm optimization (PSO algorithm and gravitational search algorithm (GSA is proposed. Although GSA has better optimization capability, it has slow convergence velocity and is easy to fall into local optimum. So in this paper, the velocity vector and position vector of GSA are adjusted by PSO algorithm in order to improve its convergence speed and prediction accuracy. Finally, the proposed hybrid algorithm is adopted to optimize the parameters of FNN soft-sensor model. Simulation results show that the model has better generalization and prediction accuracy for the concentrate grade and tailings recovery rate to meet the online soft-sensor requirements of the real-time control in the flotation process.

  10. Characterization and potential application of pataua vegetable oil in apatite flotation; Caracterizacao e potencial aplicacao do oleo vegetal de pataua na floracao de apatita

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, P.S. de; Mansur, H.S.; Peres, A.E.C., E-mail: eng.priscila.oliveira@gmail.com [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil)

    2016-07-01

    The present research characterizes the Pataua palm (Oenocarpus bataua) oil regarding to its fatty acids profile and acidity index, and evaluates its use for apatite flotation. The Pataua oil evaluated is unsaturated e predominantly composed of cis-9-octadecenoic acid (oleic acid). The mineral sample characterization revealed a material composed by a fluoroapatite deficient in fluorine, a possibly result of isomorphic substitution, and with quartz and monazite inclusions. The analysis of the mineral after reagent conditioning, by Fourier Transform Infrared Spectroscopy (FTIR), pointed to the presence of characteristic bands of carbon chains and carboxylate group, suggesting the collector adsorption through the mechanisms of chemisorption and insoluble calcium salts precipitation. Thus, it is proposed the Pataua oil potential use in flotation systems aiming apatite recovery. (author)

  11. Simple Fecal Flotation Is a Superior Alternative to Guadruple Kato Katz Smear Examination for the Detection of Hookworm Eggs in Human Stool

    OpenAIRE

    Inpankaew, Tawin; Schär, Fabian; Khieu, Virak; Muth, Sinuon; Dalsgaard, Anders; Marti, Hanspeter; Traub, Rebecca J.; Odermatt, Peter

    2014-01-01

    BACKGROUND: Microscopy-based identification of eggs in stool offers simple, reliable and economical options for assessing the prevalence and intensity of hookworm infections, and for monitoring the success of helminth control programs. This study was conducted to evaluate and compare the diagnostic parameters of the Kato-Katz (KK) and simple sodium nitrate flotation technique (SNF) in terms of detection and quantification of hookworm eggs, with PCR as an additional reference test in stool, co...

  12. Comparison of formalin-ethyl ether sedimentation, formalin-ethyl acetate sedimentation, and zinc sulfate flotation techniques for detection of intestinal parasites.

    OpenAIRE

    Truant, A L; Elliott, S H; Kelly, M T; Smith, J H

    1981-01-01

    Formalin-ethyl ether sedimentation, Formalin-ethyl acetate sedimentation, and zinc sulfate flotation techniques were compared using over 250 clinical parasitology specimens. Fifty positive specimens were identified, and a variety of parasites, including amoebae, flagellates, cestodes, nematodes, and trematodes, were encountered. The Formalin-ether and Formalin-ethyl acetate sedimentation procedures gave identical results for the detection of cysts, ova, and larvae, and these methods offered a...

  13. Removal of rhodamine B (a basic dye) and thoron (an acidic dye) from dilute aqueous solutions and wastewater simulants by ion flotation.

    Science.gov (United States)

    Shakir, Kamal; Elkafrawy, Ahmed Faouzy; Ghoneimy, Hussein Fouad; Elrab Beheir, Shokry Gad; Refaat, Mamdoh

    2010-03-01

    The present work deals with removal, by ion flotation, of two dyes: a basic dye (rhodamine B (RB)) and an acidic one (thoron (TH)) from dilute aqueous solutions and simulated wastewaters. These dyes are widely used for analytical and biological staining purposes. Besides, RB is commonly used in dyeing of various industrial products. Therefore, wastewaters emanating from chemical and radiochemical laboratories, and biomedical and biological research laboratories may be contaminated with RB and TH. Ion flotation of these dyes has been investigated over a wide range of pH using the anionic surfactant, sodium lauryl sulfate (NaLS) and the cationic surfactant, cetyltrimethylammonium bromide (CTAB) as collectors. Successful removals could be achieved for RB and TH with the anionic collector, NaLS, and the cationic collector, CTAB, respectively. In addition to the effects of pH and type of collector on the efficiency of removal of each dye, the effects of collector and dye concentrations, frother dosage, ionic strength, bubbling time period and presence of foreign salts were investigated and the optimal removal conditions have been established. Removals exceeding 99.5 % and 99.9% could be achieved for RB and TH, respectively. The results obtained are discussed with respect to dissociation of dye, type of collector, ionic strength and sign and magnitude of charge of added foreign ions. Kinetics of flotation were also studied. Further studies demonstrate that under optimum conditions the developed flotation processes can be applied for the treatment of dye-contaminated wastewaters simulated to those generated at dyeing industries and radiochemical laboratories. Copyright 2009 Elsevier Ltd. All rights reserved.

  14. Hybrid selective surface hydrophilization and froth flotation separation of hazardous chlorinated plastics from E-waste with novel nanoscale metallic calcium composite

    Energy Technology Data Exchange (ETDEWEB)

    Mallampati, Srinivasa Reddy, E-mail: srireddys@ulsan.ac.kr; Heo, Je Haeng; Park, Min Hee

    2016-04-05

    Highlights: • Nanometallic Ca/CaO treatment significantly enhanced PVC surface hydrophilicity. • The contact angle of PVC significantly decreased compared to other E-waste plastics. • 100% of PVC was selectively separated with 96.4% purity from E-waste plastics. • SEM/XPS results indicated an oxidative degradation of chlorides on the PVC surface. • Hybrid treatment with nanometallic Ca/CaO and froth flotation is effective. - Abstract: Treatment by a nanometallic Ca/CaO composite has been found to selectively hydrophilize the surface of polyvinyl chloride (PVC), enhancing its wettability and thereby promoting its separation from E-waste plastics by means of froth flotation. The treatment considerably decreased the water contact angle of PVC, by about 18°. The SEM images of the PVC plastic after treatment displayed significant changes in their surface morphology compared to other plastics. The SEM-EDS results reveal that a markedly decrease of [Cl] concentration simultaneously with dramatic increase of [O] on the surface of the PCV samples. XPS results further confirmed an increase of hydrophilic functional groups on the PVC surface. Froth flotation at 100 rpm mixing speed was found to be optimal, separating 100% of the PVC into a settled fraction of 96.4% purity even when the plastics fed into the reactor were of nonuniform size and shape. The total recovery of PVC-free plastics in E-waste reached nearly 100% in the floated fraction, significantly improved from the 20.5 wt% of light plastics that can be recovered by means of conventional wet gravity separation. The hybrid method of nanometallic Ca/CaO treatment and froth flotation is effective in the separation of hazardous chlorinated plastics from E-waste plastics.

  15. Formation mechanism of channel segregation in carbon steels by inclusion flotation: X-ray microtomography characterization and multi-phase flow modeling

    International Nuclear Information System (INIS)

    Cao, Yan Fei; Chen, Yun; Li, Dian Zhong

    2016-01-01

    Recent experimental dissections of steel ingots and multi-scale simulations have led to the discovery of a potential driving force for channel segregation: the flotation of oxide-based inclusion (D. Li et al., Nat. Commun. 5:5572 (2014)). Further experimental analysis and numerical modeling are necessary to clarify this mechanism in detail. In this work, the inclusions in a carbon steel ingot that exhibits severe channel segregations were characterized by the 3D X-ray microtomography, which revealed a significant enrichment and growth of inclusions in the channels. Based on above microtomography characterization, a 2D macrosegregation model encompassing the inclusion flotation was established. In the model, the motions of solid inclusions and liquid were described using the multi-phase flow scheme within the Euler-Lagrange framework. The benchmark simulations showed that sufficient inclusion populations with appropriate sizes are capable of altering the local flow patterns and destabilize the mushy zone, initiating the subsequent channel segregation. The continuous interplay between melt convection, inclusion flotation and solidification eventually causes the formation of macroscale channel. The predicted sizes and volume fraction of inclusions that are able to trigger the channel segregation effectively are consistent with the data obtained via microtomography characterization. The macrosegregation model was then applied to predict the channel segregations in an industrial carbon steel ingot. A rather good agreement of A-segregates was achieved between the simulation and the dissected ingot.

  16. Hybrid selective surface hydrophilization and froth flotation separation of hazardous chlorinated plastics from E-waste with novel nanoscale metallic calcium composite.

    Science.gov (United States)

    Mallampati, Srinivasa Reddy; Heo, Je Haeng; Park, Min Hee

    2016-04-05

    Treatment by a nanometallic Ca/CaO composite has been found to selectively hydrophilize the surface of polyvinyl chloride (PVC), enhancing its wettability and thereby promoting its separation from E-waste plastics by means of froth flotation. The treatment considerably decreased the water contact angle of PVC, by about 18°. The SEM images of the PVC plastic after treatment displayed significant changes in their surface morphology compared to other plastics. The SEM-EDS results reveal that a markedly decrease of [Cl] concentration simultaneously with dramatic increase of [O] on the surface of the PCV samples. XPS results further confirmed an increase of hydrophilic functional groups on the PVC surface. Froth flotation at 100rpm mixing speed was found to be optimal, separating 100% of the PVC into a settled fraction of 96.4% purity even when the plastics fed into the reactor were of nonuniform size and shape. The total recovery of PVC-free plastics in E-waste reached nearly 100% in the floated fraction, significantly improved from the 20.5wt% of light plastics that can be recovered by means of conventional wet gravity separation. The hybrid method of nanometallic Ca/CaO treatment and froth flotation is effective in the separation of hazardous chlorinated plastics from E-waste plastics. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Challenges related to flotation cleaning of oil shales. Issues due to compositional and surface features and post-grinding surface behavior

    Directory of Open Access Journals (Sweden)

    Altun N. Emre

    2016-01-01

    Full Text Available Oil shale is an important energy resource alternative. Despite its recognition as an unconventional oil source, oil shale is also considered as an important solid fossil fuel alternative to coal and lignites due to the solid form and remarkable extent of organic content. Utilization possibilites, similar to coal and lignites, have been considered in the past decades and direct use of oil shales in thermal power production has been possible in countries like Estonia and China. In the perspective of utilization of oil shales in a similar manner to coal and lignites, problems and restrictions related to the inorganic ash-making and potentially pollutant constituents are applied. In this respect, cleaning of this important energy source through mineral processing methods, particularly by flotation, is an outstanding option. However, on the basis of unique features and distinctive characteristics, treatment of oil shales like a type of coal is a big perception and may be highly misleading. This paper discusses specific challenges regarding flotation behavior of oil shales with reference to the surface characteristics and behavior of oil shale entities – probably the most important aspect that determines the efficiency and success of the flotation based cleaning process.

  18. The Effect of Ozone and Zeolite Concentration to the Performance of the Treatment of Wastewater Containing Heavy Metal Using Flotation Process

    Directory of Open Access Journals (Sweden)

    Eva Karamah

    2010-10-01

    Full Text Available Industrial wastewater which contains heavy metal cannot be disposed to the environment directly, due to its toxicity. In this research, separation of metal from wastewater was conducted by sorptive flotation method, using Lampung natural zeolite as bonding agent. The most common diffuser used in the flotation process is air or oxygen. In this research, ozone is used as diffuser because it is a stronger oxidant and more dissolvable in water than oxygen. Besides, ozone is a coagulant aid and disinfectant. With ozone as diffuser, it is expected that the process become faster with higher efficiency. This research was conducted to determine ozone effectiveness as diffuser, compared with other diffuser, and also to determine optimum concentration and effectiveness of zeolite in flotation of iron, nickel and copper. The research result shows that separation of iron with air diffuser is 90.8%, air-oxygen diffuser is 95.7%, air-ozone (from air diffuser is 99.7%, and air-ozone (from oxygen diffuser is 99.7%. Natural zeolite is effective as bonding agent with optimum concentration equal to 2 gram/liter, producing separation percentage for iron equal to 99.70%, copper equal to 88.98% and Nickel equal to 98.46%.

  19. Flotation-spectrophotometric determination of ruthenium in the Ru(IV)-chloride-rhodamine 6G-toluene system

    International Nuclear Information System (INIS)

    Balcerzak, M.

    1985-01-01

    The reduction of RuO 4 in hydrochloric acid has been examined. A sensitive flotation-spectrophotometric method of the determination of ruthenium based on the ion associate formed by the anionic chlorid complex of ruthenium RuCl 2- 6 with the basic dye Rhodamine 6G (R6G) has been developed. The solution of the ion associate obeys Beer's law up to the concentration of 0.25 μg Ru/ml. The ion associate precipitates when the aqueous solution is shaken with toluene. The separated compound is dissolved in acetone. The molar absorptivity (epsilon) at 530 nm is 5.1 x 10 5 l x mole -1 x cm -1 . The relative standard deviation is 3-7%. The mole ratio of Ru:R6G in the complex is 1:5. Osmium reacts similarly. The determination of ruthenium can be selective after the preliminary separation of osmium as OsO 4 . The method was applied to the determination of microgram amounts of ruthenium in crucible platinum. (Author)

  20. A flotation/sieving method to detect Echinococcus multilocularis and Toxocara spp. eggs in soil by real-time PCR

    Directory of Open Access Journals (Sweden)

    Umhang Gérald

    2017-01-01

    Full Text Available Soil can be a source of human infection by many zoonotic helminth species including Echinococcus multilocularis and Toxocara spp. The prevention of alveolar echinococcosis could be greatly improved through the identification of at-risk areas. Yet very few data are available about the detection of E. multilocularis in soil, while more studies have been reported for Toxocara spp. Identification of soil contamination by E. multilocularis eggs requires the use of specific methods. This study describes the development of a method for the detection of E. multilocularis in soil samples with the concentration of eggs using a flotation/sieving method and detection by duplex real-time polymerase chain reaction (PCR. Toxocara spp. egg detection was also undertaken due to the widespread presence of this parasite in soil, despite it being considered less pathogenic. Method sensitivity of 100% was reached for the detection of 10 E. multilocularis eggs spiked in 10 g of soil. Concerning Toxocara spp., method sensitivity was lower but assumed to be due to the reduced effectiveness of the DNA extraction protocol. The parasitological status for E. multilocularis and Toxocara spp. of 63 carnivore fecal samples collected in highly endemic rural areas of France and of soil samples collected under and near these fecal samples was compared. The contamination of soil samples collected under positive fecal samples for E. multilocularis (n = 3 or Toxocara spp. (n = 19 confirmed the transfer of eggs from the definitive host to the environment.

  1. Rapid detection and quantification of Cryptosporidium baileyi oocysts in feces and organs of chickens using a microscopic slide flotation method.

    Science.gov (United States)

    Abbassi, H; Wyers, M; Cabaret, J; Naciri, M

    2000-03-01

    A simple semiquantitative microscopic slide flotation (MSF) method using modified Sheather's sugar solution (MSSS) is presented for the rapid detection and quantification of Cryptosporidium baileyi oocysts in the feces and mucosal and/or organ scrapings of chickens. Oocyst shedding was evaluated by examination of the surface of coverslips, and the average quantitative score (0-5) recorded for 10 microscopic fields (magnification x250) is reported. The equivalence between these scores and the actual number of oocysts counted per gram of feces was assessed (rs = 0.89; P < 0.001). The applicability of this method was tested by comparison of the kinetics of oocyst shedding in feces of inoculated chickens with those reported by other authors working under similar conditions. In organs the MSF method was compared to histology. Fewer false-negative results were obtained using MSF versus the histology method. The MSF method was particularly more efficient in tracheae with low levels of infection and in the lungs, regardless of the level of infection. The MSF method was also very efficient in detecting oocysts in air sacs from chickens with aerosacculitis. It provides a specific and sufficiently sensitive, simple, rapid, reliable, and low-cost means of diagnosing C. baileyi in the feces and organs of chickens. This method can be used in the routine diagnosis of cryptosporidia in chickens, and it could be extended to other avian species and used in epidemiology studies to evaluate the prevalence of cryptosporidiosis in fowl.

  2. Feasibility of electrocoagulation/flotation treatment of waste offset printing developer based on the response surface analysis

    Directory of Open Access Journals (Sweden)

    Savka Adamovic

    2016-01-01

    Full Text Available In the printing plate developing process, the offset printing developer undergoes changes, as well as enrichment by the various chemicals, i.e. metals, organic binders and photosensitive compounds. The objective of this study was to investigate the electrocoagulation/flotation (ECF treatment efficiency for the removal of copper, turbidity and organic substances from the waste offset printing developer (WOPD. The effect of operational parameters, such as electrode materials, current density, interelectrode distance and operating time, was studied. Also, the response surface analysis was applied to evaluate the effect of main operational variables and to get a balanced removal efficiency of investigated WOPD parameters by ECF treatment. The removal efficiency increases significantly with the increasing of operating time and mainly increases with the increasing of current density. The obtained results show that the interelectrode distance and combinations of electrodes determine the removal efficiency of copper, turbidity and organic substances. Based on the obtained results, the optimized parameters for the ECF treatment removal of investigated WOPD parameters were identified as: Al(−/Fe(+ electrode combination with interelectrode distance of 1.0 cm, operating time of 5 min and current density of 8 mA cm−2. This study confirms the practical feasibility of ECF method for treating real printing industrial effluent under optimum conditions.

  3. Central Solenoid

    CERN Multimedia

    2002-01-01

    The Central Solenoid (CS) is a single layer coil wound internally in a supporting cylinder housed in the cryostat of the Liquid Argon Calorimeter. It was successfully tested at Toshiba in December 2000 and was delivered to CERN in September 2001 ready for integration in the LAr Calorimeter in 2003. An intermediate test of the chimney and proximity cryogenics was successfully performed in June 2002.

  4. Central sleep apnea

    Science.gov (United States)

    Sleep apnea - central; Obesity - central sleep apnea; Cheyne-Stokes - central sleep apnea; Heart failure - central sleep apnea ... Central sleep apnea results when the brain temporarily stops sending signals to the muscles that control breathing. The condition ...

  5. Investigation of column flotation process on sulphide ore using 2-electrode capacitance sensor: The effect of air flow rate and solid percentage

    Science.gov (United States)

    Haryono, Didied; Harjanto, Sri; Wijaya, Rifky; Oediyani, Soesaptri; Nugraha, Harisma; Huda, Mahfudz Al; Taruno, Warsito Purwo

    2018-04-01

    Investigation of column flotation process on sulphide ore using 2-electrode capacitance sensor is presented in this paper. The effect of air flow rate and solid percentage on column flotation process has been experimentally investigated. The purpose of this paper is to understand the capacitance signal characteristic affected by the air flow rate and the solid percentage which can be used to determine the metallurgical performance. Experiments were performed using a laboratory column flotation cell which has a diameter of 5 cm and the total height of 140 cm. The sintered ceramic sparger and wash water were installed at the bottom and above of the column. Two-electrode concave type capacitance sensor was also installed at a distance of 50 cm from the sparger. The sensor was attached to the outer wall of the column, connected to data acquisition system, manufactured by CTECH Labs Edwar Technology and personal computer for further data processing. Feed consisting ZnS and SiO2 with the ratio of 3:2 was mixed with some reagents to make 1 litre of slurry. The slurry was fed into the aerated column at 100 cm above the sparger with a constant rate and the capacitance signals were captured during the process. In this paper, 7.5 and 10% of solid and 2-4 L/min of air flow rate with 0.5 L/min intervals were used as independent variables. The results show that the capacitance signal characteristics between the 7.5 and 10% of solid are different at any given air flow rate in which the 10% solid produced signals higher than those of 7.5%. Metallurgical performance and capacitance signal exhibit a good correlation.

  6. Impact of Kishnica and Badovci Flotation Tailing Dams on Levels of Heavy Metals in Water of Graçanica River (Kosovo

    Directory of Open Access Journals (Sweden)

    Fatbardh Gashi

    2017-01-01

    Full Text Available The main objective of this study was to perform assessment of water quality of Graçanica River (Kosovo, impacted by Kishnica and Badovci flotation tailing dams, using ICP-OES method. The obtained results show that the mean values of all heavy metals in studied river water samples were significantly high, with following maximal concentrations: As (0.033 mgL−1, Cd (0.002 mgL−1, Cr (0.225 mgL−1, Cu (0.015 mgL−1, Hg (0.004 mgL−1, Mn (15.66 mgL−1, Ni (0.255 mgL−1, Pb (0.013 mgL−1, and Zn (0.612 mgL−1, but only two samples from locations influenced by Kishnica and Badovci flotation tailing dams showed statistically anomalous values of Cr3+, Cu2+, Mn2+, Zn2+, and Hg2+. According to assessment based on Croatian standards, locations near both flotation tailing dams are significantly polluted with majority of studied metals, while downstream sampling stations are almost unpolluted or slightly polluted. Mercury is found to be the most significant contaminant. According to WHO recommended values for drinking water, on all locations values were within the limits for Al, Cd, Cu, and Zn, while for As, Cr, Hg, Mn, Ni, and Pb values exceed recommended values on some sampling stations. Further monitoring of water and possibly sediments of Graçanica River is advised, as well as performing of remediation of Kishnica and Badovci mine tailing dams.

  7. Overproduction of individual gas vesicle proteins perturbs flotation, antibiotic production and cell division in the enterobacterium Serratia sp. ATCC 39006.

    Science.gov (United States)

    Monson, Rita E; Tashiro, Yosuke; Salmond, George P C

    2016-09-01

    Gas vesicles are intracellular proteinaceous organelles that facilitate bacterial colonization of static water columns. In the enterobacterium Serratia sp. ATCC 39006, gas vesicle formation requires the proteins GvpA1, GvpF1, GvpG, GvpA2, GvpK, GvpA3, GvpF2 and GvpF3 and the three gas vesicle regulatory proteins GvrA, GvrB and GvrC. Deletion of gvpC alters gas vesicle robustness and deletion of gvpN or gvpV results in small bicone vesicles. In this work, we assessed the impacts on gas vesicle formation when each of these 14 essential proteins was overexpressed. Overproduction of GvpF1, GvpF2, GvrA, GvrB or GvrC all resulted in significantly reduced gas vesicle synthesis. Perturbations in gas vesicle formation were also observed when GvpV and GvpA3 were in excess. In addition to impacts on gas vesicle formation, overproduction of GvrA or GvrB led to elevated biosynthesis of the tripyrrole pigment, prodigiosin, a secondary metabolite of increasing medical interest due to its antimalarial and anticancer properties. Finally, when GvpG was overexpressed, gas vesicles were still produced, but the cells exhibited a growth defect. Further analysis showed that induction of GvpG arrested cell growth and caused a drop in viable count, suggesting a possible physiological role for this protein linking gas vesicle biogenesis and binary fission. These combined results demonstrate that the stoichiometry of individual gas vesicle proteins is crucially important for controlled organelle morphogenesis and flotation and provides evidence for the first link between gas vesicle assembly and cell division, to our knowledge.

  8. A flotation/sieving method to detect Echinococcus multilocularis and Toxocara spp. eggs in soil by real-time PCR.

    Science.gov (United States)

    Umhang, Gérald; Bastien, Matthieu; Renault, Camille; Faisse, Marine; Caillot, Christophe; Boucher, Jean-Marc; Hormaz, Vanessa; Poulle, Marie-Lazarine; Boué, Franck

    2017-01-01

    Soil can be a source of human infection by many zoonotic helminth species including Echinococcus multilocularis and Toxocara spp. The prevention of alveolar echinococcosis could be greatly improved through the identification of at-risk areas. Yet very few data are available about the detection of E. multilocularis in soil, while more studies have been reported for Toxocara spp. Identification of soil contamination by E. multilocularis eggs requires the use of specific methods. This study describes the development of a method for the detection of E. multilocularis in soil samples with the concentration of eggs using a flotation/sieving method and detection by duplex real-time polymerase chain reaction (PCR). Toxocara spp. egg detection was also undertaken due to the widespread presence of this parasite in soil, despite it being considered less pathogenic. Method sensitivity of 100% was reached for the detection of 10 E. multilocularis eggs spiked in 10 g of soil. Concerning Toxocara spp., method sensitivity was lower but assumed to be due to the reduced effectiveness of the DNA extraction protocol. The parasitological status for E. multilocularis and Toxocara spp. of 63 carnivore fecal samples collected in highly endemic rural areas of France and of soil samples collected under and near these fecal samples was compared. The contamination of soil samples collected under positive fecal samples for E. multilocularis (n = 3) or Toxocara spp. (n = 19) confirmed the transfer of eggs from the definitive host to the environment. © G. Umhang et al., published by EDP Sciences, 2017.

  9. Cryogenic XPS study of fast-frozen sulfide minerals: Flotation-related adsorption of n-butyl xanthate and beyond

    Energy Technology Data Exchange (ETDEWEB)

    Mikhlin, Yuri, E-mail: yumikh@icct.ru [Institute of Chemistry and Chemical Technology of the Siberian Branch of the Russian Academy of sciences, Akademgorodok, 50/24, Krasnoyarsk 660036 (Russian Federation); Karacharov, Anton; Tomashevich, Yevgeny [Institute of Chemistry and Chemical Technology of the Siberian Branch of the Russian Academy of sciences, Akademgorodok, 50/24, Krasnoyarsk 660036 (Russian Federation); Shchukarev, Andrey [Department of Chemistry, Umeå University, Umeå SE-901 87 (Sweden)

    2016-01-15

    Highlights: • Mineral/aqueous solution interfaces were studied with quasi in situ cryo-XPS. • Dibutyl dixanthogen was the major xanthate adsorption product on pyrite. • Dixanthogen and minor cuprous xanthate were uptaken by chalcopyrite. • Xanthate was chemisorbed at PbS. • Ice-repellent character of hydrophobic particles caused charging effects in XPS. - Abstract: Cryogenic XPS of wet particulate samples separated via centrifugation and fast-frozen allows quasi in situ examination of solid surfaces, adsorbates, and reaction products, largely preventing the loss both of volatiles and hydrated species at mineral/water interfaces. Here, the cryo-XPS has been applied to characterize the surfaces and interfacial layers of natural pyrite (FeS{sub 2}), chalcopyrite (CuFeS{sub 2}), and galena (PbS) in solutions of a common flotation collector, potassium n-butyl xanthate (KBX), in conjunction with zeta-potential measurement. It was found, in particular, that dibutyl dixanthogen was the major adsorbate at pyrite in 0.1 mM KBX and 10 mM KBX solutions; dixanthogen and cuprous xanthate in the next stage were formed on chalcopyrite, and predominant chemisorbed butyl xanthate was present at galena, including in 10 mM KBX solution. The results may suggest that the production of dixanthogens at the interface has been underestimated while the quantities of surface metal xanthates could be over evaluated in previous studies. Pronounced differential charging effects were observed in the XPS experiment for the samples moderately hydrophobized by the xanthate treatment; we proposed that the effect was due to electrically isolated mineral particles with hydrophobic and ice-repellent surfaces, which retained, however, some frozen water islets.

  10. The Challenge to Scavenge IRON from Tailings Produced By FLOTATION A New Approach: The Super-WHIMS & the BigFLUX Magnetic Matrix

    Directory of Open Access Journals (Sweden)

    José Pancrácio Ribeiro

    Full Text Available Abstract Tailings recovery has been a constant challenge for most engineers. Along more than five years, GAUSTEC joined major players in the mining Industry to scavenge Iron from tailings produced by flotation making use of WHIMS (Wet High Intensity Magnetic Separation. In the early 1980s, in USA, the US 4,192,738 patent was granted with promising results. Despite this, thirty years have passed with no significant application worldwide. One main reason is reported: the market missed a really high feed capacity WHIMS in order to avoid the huge number of the WHIMS that were available at that time (such projects would typically require more than 20 WHIMS to scavenge iron from tailings produced by flotation plants. Such a huge asset to scavenge low grade iron tailings would not payback. The Mega sized WHIMS launched by GAUSTEC in 2014, the GHX-1400, improved by the Super-WHIMS Technology (18.000 Gauss and BigFlow Magnetic Matrixes (Gaps smaller than 1.5 mm, faced this challenge. Specially designed ancillary equipment described here also played a decisive role in the scene.

  11. Sustainable and Selective Separation of PVC and ABS from a WEEE Plastic Mixture Using Microwave and/or Mild-Heat Treatment with Froth Flotation.

    Science.gov (United States)

    Thanh Truc, Nguyen Thi; Lee, Byeong-Kyu

    2016-10-04

    This study reports simple, selective, and sustainable separation of chlorinated plastic (polyvinyl chloride, PVC) and acrylonitrile butadiene styrene (ABS) containing brominated flame retardants (BFRs) from mixed waste electrical and electronic equipment (WEEE) plastics using microwave and/or mild-heat treatment. Microwave treatment after plastic coating with powdered activated carbon (PAC) selectively increased the hydrophilicity of the PVC surface, which facilitated PVC separation (100% recovery and purity) from the WEEE plastic mixture under the optimum flotation conditions. A further mild-heat treatment for 100 s facilitated selective separation with the highest recovery and purity (100%) of PAC-coated ABS containing BFRs from the remaining plastic mixture due to selective formation of a twisted structure with a lower density than water and the untreated ABS. Mild-heat treatment only of PAC-coated WEEE plastic mixture resulted in successful recovery of (100%) the ABS and PVC. However, the recovered PVC had slightly reduced purity (96.8%) as compared to that obtained using the combined heat and microwave treatments. The combination of both treatments with flotation facilitated selective and sustainable separation of PVC and ABS from WEEE plastics to improve their recycling quality.

  12. A Comparative Study on the Effect of Flotation Reagents on Growth and Iron Oxidation Activities of Leptospirillum ferrooxidans and Acidithiobacillus ferrooxidans

    Directory of Open Access Journals (Sweden)

    Mohammad Jafari

    2016-12-01

    Full Text Available Recently, extraction of metals from different resources using a simple, efficient, and low-cost technique-known as bioleaching-has been widely considered, and has turned out to be an important global technology. Leptospirillum ferrooxidans and Acidithiobacillus (Thiobacillus ferrooxidans are ubiquitous bacteria in the biomining industry. To date, the effects of commercial flotation reagents on the biooxidation activities of these bacteria have not been thoroughly studied. This investigation, by using various systematic measurement methods, studied the effects of various collectors and frothers (collectors: potassium amylxanthate, potassium isobutyl-xanthate, sodium ethylxanthate, potassium isopropylxanthate, and dithiophosphate; and frothers: pine oil and methyl isobutyl carbinol on L. ferrooxidans and A. ferrooxidans activities. In general, results indicate that in the presence of these collectors and frothers, L. ferrooxidans is less sensitive than T. ferrooxidans. In addition, the inhibition effect of collectors on both bacteria is recommended in the following order: for the collectors, potassium isobutyl-xanthate > dithiophosphate > sodium ethylxanthate > potassium isobutyl-xanthate > potassium amylxanthate; and for the frothers, methyl isobutyl carbinol > pine oil. These results can be used for the optimization of biometallurgical processes or in the early stage of a process design for selection of flotation reagents.

  13. Flotation separation of PET from a PET, PVC and PS mixture by the hydrofilization of the PET surface in NaOH solutions

    Directory of Open Access Journals (Sweden)

    Ľubica Kozáková

    2005-11-01

    Full Text Available Recycling is the most effective method of waste minimization created by the human activity. The idea of waste re-use as a result of environmental, social and economical factors is becoming very relevant in the last decades. The portion of plastics in the municipal waste is growing year by year as also is its use in the wrapping industry. A condition for recycling technologies is the input of highly pure plastics (without undesirable admixtures suitable for recycling. Various separation technologies can be used which provide separation of particular components of plastic waste and contaminants. Flotation is one of the separation methods used especially for the ore beneficiation but recently is widely also used for the separation of various types of waste. Plastics, which are not possible to be separated by gravitational methods (because they have almost the same density, PET from beverage bottles, PVC from bottles and foils and PS from beverage beakers, were studied. By changing the surface properties of PET from naturally hydrophobic to hydrophilic by the adjustment in a NaOH solution, PET with the recovery of up to 99 % in the non-foamy product and with the product purity of up to 98 % was acquired by the flotation.

  14. The effect of the natural bentonite to reduce COD in palm oil mill effluent by using a hybrid adsorption-flotation method

    Science.gov (United States)

    Dewi, Ratni; Sari, Ratna; Syafruddin

    2017-06-01

    Palm oil mill effluent is waste produced from palm oil processing activities. This waste are comingfrom condensate water, process water and hydrocyclone water. The high levels of contaminants in the palm oil mill effluent causes the waste becomes inappropriate to be discharged to water body before processing, one of the most major contaminants in wastewater is fats, oils and COD.This study investigated the effectiveness of chemically activated bentonite that serves as an alternative to reduce the COD in adsorption and floatation based palm oil effluent waste processing. Natural bentonite was activated by using nitrit acid and benzene. In the existing adsorption material to improve COD reduction capability whereas the flotation method was used to further remove residual effluent which is still remain after the adsorption process. An adsorption columns which operated in batch was used in the present study. By varying the circulation time and adsorbent treatment (activated and non-activated), it was shown that percentage of COD reduction reached 75% at the circulation time of 180 minutes for non activated adsorbent. On the other hand the percentof COD reduction in adsorption and flotation process using activated bentonite reached as high as 88% and 93% at the circulation time of 180 minutes.

  15. A Low Viscosity Lunar Magma Ocean Forms a Stratified Anorthitic Flotation Crust With Mafic Poor and Rich Units: Lunar Magma Ocean Viscosity

    Energy Technology Data Exchange (ETDEWEB)

    Dygert, Nick [Department of Geological Sciences, Jackson School of Geosciences, University of Texas at Austin, Austin TX USA; Planetary Geosciences Institute, Department of Earth and Planetary Sciences, University of Tennessee, Knoxville, Knoxville TN USA; Lin, Jung-Fu [Department of Geological Sciences, Jackson School of Geosciences, University of Texas at Austin, Austin TX USA; Marshall, Edward W. [Department of Geological Sciences, Jackson School of Geosciences, University of Texas at Austin, Austin TX USA; Kono, Yoshio [HPCAT, Geophysical Laboratory, Carnegie Institution of Washington, Argonne IL USA; Gardner, James E. [Department of Geological Sciences, Jackson School of Geosciences, University of Texas at Austin, Austin TX USA

    2017-11-21

    Much of the lunar crust is monomineralic, comprising >98% plagioclase. The prevailing model argues the crust accumulated as plagioclase floated to the surface of a solidifying lunar magma ocean (LMO). Whether >98% pure anorthosites can form in a flotation scenario is debated. An important determinant of the efficiency of plagioclase fractionation is the viscosity of the LMO liquid, which was unconstrained. Here we present results from new experiments conducted on a late LMO-relevant ferrobasaltic melt. The liquid has an exceptionally low viscosity of 0.22 $+0.11\\atop{-0.19}$to 1.45 $+0.46\\atop{-0.82}$ Pa s at experimental conditions (1,300–1,600°C; 0.1–4.4 GPa) and can be modeled by an Arrhenius relation. Extrapolating to LMO-relevant temperatures, our analysis suggests a low viscosity LMO would form a stratified flotation crust, with the oldest units containing a mafic component and with very pure younger units. Old, impure crust may have been buried by lower crustal diapirs of pure anorthosite in a serial magmatism scenario.

  16. Effects of toxic organic flotation reagent (aniline aerofloat) on an A/O submerged membrane bioreactor (sMBR): Microbial community dynamics and performance.

    Science.gov (United States)

    Lin, Weixiong; Sun, Shuiyu; Wu, Chun; Xu, Pingting; Ye, Ziwei; Zhuang, Shengwei

    2017-08-01

    Bio-treatment of flotation wastewater has been proven to be both effective and economical, as a treatment method. Despite this, little is known regarding the effects of toxic organic floatation reagents such as Dianilinodithiophosphoric acid (DDA), on the microbial community performance or dynamics, which are critical to the effective performance of the bio-treatment reactor. A submerged membrane bioreactor (sMBR) was constructed to continuously treat simulated wastewater contaminated with DDA, an organic flotation reagent that is now considered a significant pollutant. The performance of the sMBR system was investigated at different DDA loading concentrations, with assessment of the effects of DDA on the microbial communities within the sMBR, in particular the biodiversity and succession within the microbial community. Results showed that, with increased DDA loadings, the performance of the sMBR was initially negatively affected, but the system adapted efficiently and consistently reached a COD removal rate of up to 80%. Increased DDA loading concentrations had an adverse effect on the activity of both the activated sludge and microbial communities, resulting in a large alteration in microbial dynamics, especially during the start-up stage and the high DDA loading stage. Strains capable of adapting to the presence of DDA, capable of degrading DDA or utilizing its byproducts, were enriched within the sMBR community, such as Zoogloea, Clostridium, Sideroxydans lithotrophicus, Thiobacillus, Thauera amino aromatica and Alicycliphilus denitrificans. Copyright © 2017 Elsevier Inc. All rights reserved.

  17. A hybrid froth flotation-filtration system as a pretreatment for oil sands tailings pond recycle water management: Bench- and pilot-scale studies.

    Science.gov (United States)

    Loganathan, Kavithaa; Bromley, David; Chelme-Ayala, Pamela; Gamal El-Din, Mohamed

    2015-09-15

    Through sustainable water management, oil sands companies are working to reduce their reliance on fresh water by minimizing the amount of water required for their operations and by recycling water from tailings ponds. This study was the first pilot-scale testing of a hybrid technology consisting of froth flotation combined with filtration through precoated submerged stainless steel membranes used to treat recycle water from an oil sands facility. The results indicated that the most important factor affecting the performance of the hybrid system was the influent water quality. Any rise in the levels of suspended solids or total organic carbon of the feed water resulted in changes of chemical consumption rates, flux rates, and operating cycle durations. The selections of chemical type and dosing rates were critical in achieving optimal performance. In particular, the froth application rate heavily affected the overall recovery of the hybrid system as well as the performance of the flotation process. Optimum surfactant usage to generate froth (per liter of treated water) was 0.25 mL/L at approximately 2000 NTU of influent turbidity and 0.015 mL/L at approximately 200 NTU of influent turbidity. At the tested conditions, the optimal coagulant dose was 80 mg/L (as Al) at approximately 2000 NTU of influent turbidity and recycle water. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. RAPID AND SENSITIVE DETERMINATION OF PALLADIUM USING HOMOGENEOUS LIQUID-LIQUID MICROEXTRACTION VIA FLOTATION ASSISTANCE FOLLOWED BY GRAPHITE FURNACE ATOMIC ABSORPTION SPECTROMETRY

    Directory of Open Access Journals (Sweden)

    Mohammad Rezaee

    2015-05-01

    Full Text Available A method for the determination of trace amounts of palladium was developed using homogeneous liquid-liquid microextraction via flotation assistance (HLLME-FA followed by graphite furnace atomic absorption spectrometry (GFAAS. Ammonium pyrrolidine dithiocarbamate (APDC was used as a complexing agent. This was applied to determine palladium in three types of water samples. In this study, a special extraction cell was designed to facilitate collection of the low-density solvent extraction. No centrifugation was required in this procedure. The water sample solution was added to the extraction cell which contained an appropriate mixture of extraction and homogeneous solvents. By using air flotation, the organic solvent was collected at the conical part of the designed cell. Parameters affecting extraction efficiency were investigated and optimized. Under the optimum conditions, the calibration graph was linear in the range of 1.0-200 µg L-1 with a limit of detection of 0.3 µg L-1. The performance of the method was evaluated for the extraction and determination of palladium in water samples and satisfactory results were obtained. In order to verify the accuracy of the approach, the standard addition method was applied for the determination of palladium in spiked synthetic samples and satisfactory results were obtained.

  19. The influence of floc size and hydraulic detention time on the performance of a dissolved air flotation (DAF) pilot unit in the light of a mathematical model.

    Science.gov (United States)

    Moruzzi, R B; Reali, M A P

    2014-12-01

    The influence of floc size and hydraulic detention time on the performance of a dissolved air flotation (DAF) pilot unit was investigated in the light of a known mathematical model. The following design and operational parameters were considered: the hydraulic detention time (tdcz) and hydraulic loading rate in the contact zone, the down-flow loading rate in the clarification zone, the particle size distribution (d F), and the recirculation rate (p). As a reference for DAF performance analysis, the proposed β.td parameter from the above mentioned mathematical model was employed. The results indicated that tdcz is an important factor in DAF performance and that d F and floc size are also determinants of DAF efficiency. Further, β.td was sensitive to both design and operational parameters, which were varied in the DAF pilot plant. The performance of the DAF unit decreases with increasing β.td values because a higher td (considering a fixed β) or a higher β (e.g., higher hydrophobicity of the flocs for a fixed td) would be necessary in the reaction zone to reach desired flotation efficiency.

  20. Flotation of Magnetite Crystals upon Decompression - A Formation Model for Kiruna-type Iron Oxide-Apatite Deposits

    Science.gov (United States)

    Knipping, J. L.; Simon, A. C.; Fiege, A.; Webster, J. D.; Reich, M.; Barra, F.; Holtz, F.; Oeser-Rabe, M.

    2017-12-01

    after decompression in the upper part of the experimental products, indicating that magnetite flotation can be an efficient mechanism to separate and accumulate magnetite. [1] Hurwitz and Navon (1994) Earth Planet. Sci. Lett.122, 267-280 [2] Edmonds et al. (2014) Geol. Soc. London, Spec. Pub. 410. [3] Simon et al. (2004) Geochim. Cosmochim. Acta 68, 4905-4914.

  1. Evaluating the impact of water flotation and the state of the wood in archaeological wood charcoal remains: Implications for the reconstruction of past vegetation and identification of firewood gathering strategies at Tell Qarassa North (south Syria)

    DEFF Research Database (Denmark)

    Otaegui, Amaia Arranz

    2016-01-01

    they are present before and after flotation. To test some of the patterns observed in the archaeological material a small-scale experiment on modern wood charcoal remains is carried out. The results enable a critic reconstruction of the type of vegetation and firewood gathering strategies at Tell Qarassa North...

  2. Developments in gold and silver recovery through flotation in processing of gold ore slags; Avances en la recuperacion de oro y plata mediante flotacion en escorias de procesamiento de menas de oro

    Energy Technology Data Exchange (ETDEWEB)

    Hidalgo, N.; Diaz, A.; Bazan, V.; Sarquis, P.

    2015-07-01

    The aim of this work is to recover and improve the extraction of gold and silver present in smelting slags through various mineralogical processes applicable in gold ores. The slag was concentrated in a Knelson type centrifuge, two concentrates (C1 and C2 and a tailing T1) being obtained. In order to improve the recovery, three series of rougher flotation tests were conducted on the tailing T1. The variables analyzed were: particle size, type of collectors (xanthates, di-monothiophosphate) and flotation time. It was deduced that by applying gravity concentration, the recovery of Au and Ag (Knelson centrifuge) is 42.0% and 13.7%, respectively. Au recovery is improved by 87.7% through the flotation of the centrifuge separation tailings, whereas that for Ag is 47.4%. The optimum conditions were: particle size 200 mesh, collectors: PAX (15.8 g/t), F-C5439 (18.75 g/t), MIBC frother (12.5g/t) and 8.5 minutes of flotation time. (Author)

  3. Total flotation and backfill

    Directory of Open Access Journals (Sweden)

    Carlos Villachica León

    2001-03-01

    Full Text Available Kolektívna flotácia a zavážanie (TFB boli navrhnuté ako ve¾mi výhodný technologický postup pre dosiahnutie trvalého rozvoja pri podzemnej ažbe polymetalických rúd v Peru. Táto technológia zlepšuje ekonomiku, znaène znižuje väèšinu environmentálnych problémov, ktoré súvisia s prevádzkovaním jemných odpadov, kyslými vodami a nadmerným používaním chemikálií v úpravniach.Kolektívna flotácia (TF je založená na mimoriadne hrubom mletí a flotácii sulfidov neželezných kovov s výnimkou pyritu. Získaný produkt je kolektívny koncentrát s hmotnosou 15-25 % hmotnosti vyaženej rudy. Postup umožòuje ve¾mi jednoduchú schému aplikácie flotaèného režimu a flotaèného okruhu bez stupòov triedenia, zahusovania a filtrácie. Úpravne pracujúce v TF režime sú tak malé, že ich je možné inštalova v podzemí, èím sa znaène znížia náklady a infraštruktúra potrebné pre manipuláciu s rudou a jej dopravou na povrch.Odpady z TF prevádzkovanej v podzemí sú hrubozrné takže je možné ich zavážanie bez predchádzajúceho triedenia za úèelom odstránenia jemných podielov. Tým sa znižuje množstvo odpadu, ktoré sa má èerpa na povrch až na 5-10 % hmotnosti vyaženej rudy. Kolektívny koncentrát sa èerpá na povrch, kde sa premie¾a a separuje na koncentráty Cu, Pb a Zn a pyritový koncentrát. V prípade Peru táto separaèná jednotka (SP môže by vzdialená od miesta ažby.V prípade novej baníckej technológie TFB dochádza k dramatickým zmenám pri návrhu a projektovaní banského diela. Technológiu TFB je možné tiež úspešne aplikova v jestvujúcich baniach, kde je nutné aži hlboko uložené ložiská. V tejto práci sa popisujú skúšky s TFB technológiou pre Zn-Pb ložisko ve¾kej håbky. V týchto skúškach sa dosiahli výažnosti pre Zn a Pb do 90 % pre koncentrát tvoriaci 15 % vyaženej rudy pri hrubom mletí (25 % - 200 mesh pri porovnaní s jemným mletím (57-60 % - 200 mesh , ktoré sa aplikuje na štandardných úpravniach s produkciou selektívnych koncentrátov. Výsledky flotaèných testov pri jemnosti mletia 18 % - 200 mesh je potrebné zlepši doplòujúcou gravitaènou úpravou. Testy perlokácie ukázali, že odpady z TF procesu je možné priamo použi pre zavážanie banského diela.Pri štúdiu kinetiky flotácie sa zistilo, že v porovnaní so štandardným flotaèným okruhom je tiež výhodná a že pre TFB proces sa vyžadovali maximálne 2 flotaèné cely s èasom zdržania 10 minút. Stupeò kondiciovania sa vylúèil prípravou zmesi umožòujúcej simultánnu aktiváciu a nakoncentrovanie sulfidov Zn v rámci stupòa mletia. Vïaka tomuto postupu bolo možné uvažova o TFB ako o technologickom postupe.

  4. Soil contamination with Toxocara spp. eggs in the public parks of Isfahan City, Central Iran

    Directory of Open Access Journals (Sweden)

    Mohsen Ghomashlooyan

    2015-06-01

    Full Text Available Objective: To evaluate the contamination rate of the public parks of Isfahan city with Toxocara spp. eggs. Methods: A total of 140 soil samples were collected from 28 public parks of Isfahan City, Central Iran, during the summer of 2014. Soil samples were investigated for the presence of Toxocara eggs by flotation method using sucrose solution. The prepared wet mount slides were examined under light microscope using 10 × and 40 × objectives. Results: Toxocara spp. eggs were found in 21 (75% out of 28 studied public parks. Also Toxocara spp. eggs were observed in 40 (28.6% out of 140 collected soil samples. Conclusions: Contamination rate with Toxocara spp. eggs in Isfahan is fairly high. Isfahan is a city that has lots of parks and gardens. The stray dogs and cats that roam around the parks contaminate the soil. Therefore preventive measures, especially for children, should be implemented.

  5. Separation tests of heavy metals in samples of industrial wastes through flotation; Pruebas de separacion de metales pesados en muestras de residuos industriales mediante flotacion

    Energy Technology Data Exchange (ETDEWEB)

    Abrego L, J

    1995-12-15

    Samples of residual muds, taken at the exit of the filter-press of the water treatment plant of a galvanoplastics industry in Lerma, Estado de Mexico, its were prepared for its qualitative and quantitative analysis. Likewise, the residual waters of the cistern located at the end of the electrodeposition process, was subjected to qualitative chemical analysis for the neutron activation technique and to quantitative analysis by atomic absorption spectrometry. The samples were treated by a flotation process by means of the one which it was studied the heavy metals removal. The results show that the AP-845 collector is the one that better it fulfilled the objectives since, it solves the problem, unless by the copper that although their concentration in the residual waters drop a lot, it was not inside the standard. (Author)

  6. Central Diabetes Insipidus, Central Hypothyroidism, Renal Tubular ...

    African Journals Online (AJOL)

    diseases, primary hypothyroidism, and other disorders of the central nervous, gastrointestinal, genitourinary, and orthopedic systems. In this report, we describe a 3‑month‑old Saudi boy with the rare association of DWS with central diabetes insipidus, congenital central hypothyroidism, and type‑2 renal tubular acidosis.

  7. Comparison of Bispectral Index™ values during the flotation restricted environmental stimulation technique and results for stage I sleep: a prospective pilot investigation.

    Science.gov (United States)

    Dunham, C Michael; McClain, Jesse V; Burger, Amanda

    2017-11-29

    To determine whether Bispectral Index™ values obtained during flotation-restricted environment stimulation technique have a similar profile in a single observation compared to literature-derived results found during sleep and other relaxation-induction interventions. Bispectral Index™ values were as follows: awake-state, 96.6; float session-1, 84.3; float session-2, 82.3; relaxation-induction, 82.8; stage I sleep, 86.0; stage II sleep, 66.2; and stages III-IV sleep, 45.1. Awake-state values differed from float session-1 (%difference 12.7%; Cohen's d = 3.6) and float session-2 (%difference 14.8%; Cohen's d = 4.6). Relaxation-induction values were similar to float session-1 (%difference 1.8%; Cohen's d = 0.3) and float session-2 (%difference 0.5%; Cohen's d = 0.1). Stage I sleep values were similar to float session-1 (%difference 1.9%; Cohen's d = 0.4) and float session-2 (%difference 4.3%; Cohen's d = 1.0). Stage II sleep values differed from float session-1 (%difference 21.5%; Cohen's d = 4.3) and float session-2 (%difference 19.6%; Cohen's d = 4.0). Stages III-IV sleep values differed from float session-1 (%difference 46.5%; Cohen's d = 5.6) and float session-2 (%difference 45.2%; Cohen's d = 5.4). Bispectral Index™ values during flotation were comparable to those found in stage I sleep and nadir values described with other relaxation-induction techniques.

  8. A novel capillary electrophoresis method with pressure assisted field amplified sample injection in determination of thiol collectors in flotation process waters.

    Science.gov (United States)

    Sihvonen, T; Aaltonen, A; Leppinen, J; Hiltunen, S; Sirén, H

    2014-01-17

    A new capillary electrophoresis method was developed for the quantification of diisobutyldithiophosphate (DTP), diisobutyldithiophosphinate (DTPI) and ethyl and isobutyl xanthates (EX, IBX) all of which are used as thiol collectors in froth flotation. This method uses pressure assisted field amplified sample injection (PA-FASI) to concentrate the analytes at the capillary inlet. The background electrolyte in electrophoretic separation was 60millimolar (mM) from 3-(cyclohexylamino)propane-1-sulfonic acid (CAPS) in 40mM NaOH solution. The similar CAPS electrolyte solution has earlier been used for screening for diuretics that contained sulphonamide and/or carboxylic groups. In this study, the functional groups are xanthate, phosphate and phosphinate. The method was developed using actual flotation process waters. The results showed that the water delivered from the plant did not contain significant amount of collectors; therefore, method development was accomplished by spiking analytes in these waters. Separation of analytes was achieved in 15min. The range of quantification was 0.27-66.6mg/L (R(2) 0.9991-0.9999) for all analytes other than ethyl xanthate, for which the range was 0.09-66.6mg/L (R(2) 0.9999). LOD (S/N=3) and LOQ (S/N=10) values for DTP, DTPI, IBX and EX were 0.05, 0.07, 0.06 and 0.01mg/L and 0.16, 0.25, 0.21 and 0.04mg/L, respectively. No interference from the matrices was observed, when the method was tested at a gold concentrator plant. Copyright © 2014 Elsevier B.V. All rights reserved.

  9. Flow injection analysis of ethyl xanthate by gas diffusion and UV detection as CS2 for process monitoring of sulfide ore flotation.

    Science.gov (United States)

    Cordeiro, Thiago G; Hidalgo, Pilar; Gutz, Ivano G R; Pedrotti, Jairo J

    2010-07-15

    A sensitive and robust analytical method for spectrophotometric determination of ethyl xanthate, CH(3)CH(2)OCS(2)(-) at trace concentrations in pulp solutions from froth flotation process is proposed. The analytical method is based on the decomposition of ethyl xanthate, EtX(-), with 2.0 mol L(-1) HCl generating ethanol and carbon disulfide, CS(2). A gas diffusion cell assures that only the volatile compounds diffuse through a PTFE membrane towards an acceptor stream of deionized water, thus avoiding the interferences of non-volatile compounds and suspended particles. The CS(2) is selectively detected by UV absorbance at 206 nm (epsilon=65,000 L mol(-1) cm(-1)). The measured absorbance is directly proportional to EtX(-) concentration present in the sample solutions. The Beer's law is obeyed in a 1x10(-6) to 2x10(-4) mol L(-1) concentration range of ethyl xanthate in the pulp with an excellent correlation coefficient (r=0.999) and a detection limit of 3.1x10(-7) mol L(-1), corresponding to 38 microg L(-1). At flow rates of 200 microL min(-1) of the donor stream and 100 microL min(-1) of the acceptor channel a sampling rate of 15 injections per hour could be achieved with RSDapplications demonstrate the versatility of the FIA method: (i) evaluation the free EtX(-) concentration during a laboratory study of the EtX(-) adsorption capacity on pulverized sulfide ore (pyrite) and (ii) monitoring of EtX(-) at different stages (from starting load to washing effluents) of a flotation pilot plant processing a Cu-Zn sulfide ore. Copyright 2010 Elsevier B.V. All rights reserved.

  10. Bench-scale testing of on-line control of column flotation using a novel analyzer. Third quarterly technical progress report, April 1, 1993--June 30, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-08-24

    This document contains the third quarterly technical progress report for PTI`s Bench-Scale Testing Project of a circuit integrating PTI`s KEN-FLOTETM Column Flotation Technology and PTI`s On-Line Quality Monitor and Control System. The twelve-month project involves installation and testing of a 200--300 lb/hr. bench-scale flotation circuit at PETC`s Coal Preparation Process Research Facility (CPPRF) for two bituminous coals (Upper Freeport and Pittsburgh No. 8 Seam Raw Coals). Figure 1 contains the project plan, as well as the approach to completing the major tasks within the twelve-month project schedule. The project is broken down into three phases, which include: Phase I -- Preparation: The preparation phase was performed principally at PTI`s Calumet offices from October through December, 1992. It involved building of the equipment and circuitry, as well as some preliminary design and equipment testing; Phase II -- ET Circuit Installation and Testing: This installation and testing phase of the project was performed at PETC`s CPPRF from January through June, 1993, and was the major focus of the project. It involved testing of the continuous 200--300 lb/hr. circuit; and Phase III -- Project Finalization: The project finalization phase is occurring from July through September, 1993, at PTI`s Calumet offices and involves finalizing analytical work and data evaluation, as well as final project reporting. This Third Quarterly Technical Progress Report principally summarizes the results from the benchscale testing with the second coal (Pittsburgh No. 8 Seam Coal), which occurred in April through June, 1993. It also contains preliminary economic evaluations that will go into the Final Report, as well as the plan for the final reporting task.

  11. Central Nervous System Vasculitis

    Science.gov (United States)

    ... Forms of Vasculitis / Central Nervous System (CNS) Vasculitis Central Nervous System (CNS) Vasculitis Swap out your current Facebook Profile ... your Facebook personal page. Replace with this image. Central nervous system (CNS) vasculitis is inflammation of blood vessel walls ...

  12. Evaluating the impact of water flotation and the state of the wood in archaeological wood charcoal remains: Implications for the reconstruction of past vegetation and identification of firewood gathering strategies at Tell Qarassa North (south Syria)

    DEFF Research Database (Denmark)

    Otaegui, Amaia Arranz

    2016-01-01

    that in certain cases, hyper-fragmentation or complete destruction of charred plant macroremains occurs as soon as they come into contact with water. At the early Pre-Pottery Neolithic B site of Tell Qarassa North (south Syria) the destruction of wood charcoal remains was documented during the flotation process....... The aim of this work is to evaluate the assemblage and to determine the factors that conditioned the preservation or disintegration of wood charcoal remains. In particular, attention is paid to the distribution of the alterations (e.g. vitrification, decayed wood) by taxa, and the proportions with which...... they are present before and after flotation. To test some of the patterns observed in the archaeological material a small-scale experiment on modern wood charcoal remains is carried out. The results enable a critic reconstruction of the type of vegetation and firewood gathering strategies at Tell Qarassa North...

  13. Separation of oily materials in radioactive waste waters by flotation. Determination of operation and control parameters; Separacion de materiales oleosos en aguas residuales radiactivas por flotacion. Determinacion de parametros de operacion y control

    Energy Technology Data Exchange (ETDEWEB)

    Ortiz O, H.B.; Flores E, R.M. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: huemantzin@prodigy.net.mx

    2003-07-01

    In this work the determination of the operation and control parameters (air/solids ratio G/S, retention time {theta}, pressure P and de pressurized volume of mixed air-water V), of the flotation system used in the treatment of oleaginous residual water (polluted mainly with {sup 60} Co) coming from the decontamination process of worn out oils, using as response parameters the concentration of oleaginous material and the residual turbidity. The obtained results allowed to observe the dependence of G/S with the pressure and volume of air-water given. At the same time it was settled down that the set of operation conditions that offers the greater separation percentage of G As and turbidity in the smallest time, they are those obtained by V{sub 2} = 0.0012 m{sup 3} and P{sub 2} = 620 kPa, (G/S = 0.30 - 0.35, = 14-16 min) for what were employees as the ideal values of operation and control in the flotation system. As long as, the concentration of total Co is found under 1 mgL{sup -1}. Finally, the selected flotation system showed high separation levels of {sup 60} Co, whose specific activity are below of 0.007 BqmL{sup -1}. (Author)

  14. Observations of central stars

    International Nuclear Information System (INIS)

    Lutz, J.H.

    1978-01-01

    Difficulties occurring in the observation of central stars of planetary nebulae are reviewed with emphasis on spectral classifications and population types, and temperature determination. Binary and peculiar central stars are discussed. (U.M.G.)

  15. NIDDK Central Repository

    Data.gov (United States)

    U.S. Department of Health & Human Services — The NIDDK Central Repository stores biosamples, genetic and other data collected in designated NIDDK-funded clinical studies. The purpose of the NIDDK Central...

  16. Engineering Development of Advanced Physical Fine Coal Cleaning Technologies: Froth flotation. Quarterly technical progress report No. 21, October 1, 1993--December 31, 1993

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-31

    A study conducted by Pittsburgh Energy Technology Center of sulfur emissions from about 1,300 United States coal-fired utility boilers indicated that half of the emissions were the result of burning coals having greater than 1.2 pounds of SO{sub 2} per million BTU. This was mainly attributed to the high pyritic sulfur content of the boiler fuel. A significant reduction in SO{sub 2} emissions could be accomplished by removing the pyrite from the coals by advanced physical fine coal cleaning. The overall project scope of the engineering development project is to conceptually develop a commercial flowsheet to maximize pyritic sulfur reduction at practical energy recovery values. This is being accomplished by utilizing the basic research data on the surface properties of coal, mineral matter and pyrite obtained from the Coal Surface Control for Advanced Fine Coal Flotation Project, to develop this conceptual flowsheet. The conceptual flowsheet must be examined to identify critical areas that need additional design data. This data will then be developed using batch and semi-continuous bench scale testing. In addition to actual bench scale testing, other unit operations from other industries processing fine material will be reviewed for potential application and incorporated into the design if appropriate.

  17. Combination of flotation and flame atomic absorption spectrometry for determination, preconcentration and separation of trace amounts of metal ions in biological samples.

    Science.gov (United States)

    Ghaedi, Mehrorang; Niknam, Khodabakhsh; Nasiri kokhdan, Syamak; Soylak, Mustafa

    2013-05-01

    An efficient enrichment procedure based on the combination of flame atomic absorption spectrometry (FAAS) and flotation for determination of Cd(2+), Ag(+) and Zn(2+) ions in various biological samples using new collector is studied. The influence of pH, amount of 2-(((1H-benzo[d]imidazol-2-yl)methoxy)methyl)-1H-benzo[d]imidazole (HBIMMHBI) as collector, sample matrix, type and amount of eluting agent, type and amount of surfactant as floating agent, ionic strength and air flow rates on the extraction efficiency were evaluated and optimized. It is ascertained that under study metal ions is preconcentrated simultaneously from matrix in the presence of 0.005 M HBIMMHBI, 0.085% (w/v) of SDS form 750 mL at pH 6.5. The floated complexes metal ions eluted quantitatively with 6 mL of 1.0 M HNO3 in methanol lead to achieve preconcentration factor of 125. The detection limits for analyte ions were in the range of 1.3-2.4 ng mL(-1), with recoveries more than 95% and relative SD lower than 4%.

  18. Development of a flotation method for preconcentration-separation of trace amounts of some metal ions in plant tissues prior to their FAAS determinations

    Directory of Open Access Journals (Sweden)

    M. Ghaedi

    2010-01-01

    Full Text Available An efficient flotation method based on the combination of flame atomic absorption spectrometry (FAAS and separation and preconcentration step for determination of Cr3+, Cu 2+, Co2+, Ni2+, Zn2+, Cd 2+, Fe3+ and Pb2+ ions in various real samples by the possibility of applying bis(2-hydroxyacetophenone-1,4-butanediimine (BHABDI as a new collector was studied. The influence of pH, amount of BHABDI as collector, sample matrix, type and amount of eluting agent, type and amount of surfactant as floating agent, ionic strength and air flow rates i.e. variables affecting the efficiency of the extraction system was evaluated. It is ascertained that metal ions such as iron can be separated simultaneously from matrix in the presence of 0.012 mM ligand, 0.025% (w/v of CTAB to a test sample of 750 mL at pH 6.5. These ions can be eluted quantitatively with 6 mL of 1.0 mol L-1 HNO3 in methanol which lead to the enrichment factor of 125. The detection limits for analyte ions were in the range of 1.3-2.4 ng mL-1. The method has been successfully applied for determination of trace amounts of ions in various real samples.

  19. Insights into the selective adsorption mechanism of a novel flotation reagent 4-Amino-5-mercapto-1,2,4-triazole on chalcopyrite surface: an experimental and computational study.

    Science.gov (United States)

    Yin, Zhigang; Hu, Yuehua; Sun, Wei; Zhang, Chenyang; He, Jianyong; Xu, Zhijie; Zou, Jingxiang; Guan, Changping; Zhang, Chen Hu; Guan, Qingjun; Lin, Shangyong

    2018-02-28

    In the present study, a novel compound 4-Amino-5-mercapto-1,2,4-triazole was first synthesized and its selective adsorption mechanism on the surface of chalcopyrite was comprehensively investigated using UV-vis spectra, Zeta potential, Fourier Transform Infrared Spectroscopy(FTIR), X-ray Photoelectron Spectroscopy Measurements(XPS), and Time of Flight Secondary Ion Mass Spectrometry (ToF-SIMS) and first principle calculations. The experimental and computational results consistently demonstrated that AMT would chemisorb onto the chalcopyrite surface by the formation of a five-membered chelate ring. The first principle periodic calculations further indicated that AMT would prefer to adsorb onto Cu rather than Fe due to the more negative adsorption energy of AMT on Cu in the chalcopyrite (001) surface, which was further confirmed by the coordination bonding energies of AMT-Cu and AMT-Fe based on the simplified cluster models at a higher accuracy level (UB3LYP/Def2-TZVP). The bench scale results indicated that the selective index improved significantly when using AMT as a chalcopyrite depressant in Cu-Mo flotation separation.

  20. Oncoplastic central quadrantectomies

    Science.gov (United States)

    Pasta, Vittorio; D’Orazi, Valerio; Merola, Raffaele; Frusone, Federico; Amabile, Maria Ida; Buè, Rosanna; Monti, Marco

    2016-01-01

    Tumors localized in the central quadrant (centrally located breast tumors) have always represented a challenge for the surgeon because of the critical aesthetical matters related to the nipple-areola complex (NAC). Many years of experience with breast cancer patients treated by using various oncoplastic techniques, has allowed us to develop the modified hemibatwing for the treatment of central breast tumors, where the NAC is involved. Modified hemibatwing—along with the removal of the NAC—is a useful oncoplastic technique and it represents an ideal option for the treatment of central tumors because it assures oncological safety, a reduced surgical timetable and greater aesthetical results. PMID:27563564

  1. Central Laboratories Services

    Data.gov (United States)

    Federal Laboratory Consortium — The TVA Central Laboratories Services is a comprehensive technical support center, offering you a complete range of scientific, engineering, and technical services....

  2. Heterogeneous nano-Fe/Ca/CaO catalytic ozonation for selective surface hydrophilization of plastics containing brominated and chlorinated flame retardants (B/CFRs): separation from automobile shredder residue by froth flotation.

    Science.gov (United States)

    Mallampati, Srinivasa Reddy; Lee, Byoung Ho; Mitoma, Yoshiharu; Simion, Cristian

    2017-02-01

    One method of weakening the inherently hydrophobic surface of plastics relevant to flotation separation is heterogeneous nano-Fe/Ca/CaO catalytic ozonation. Nano-Fe/Ca/CaO-catalyzed ozonation for 15 min efficiently decreases the surface hydrophobicity of brominated and chlorinated flame retardant (B/CFR)-containing plastics (such as acrylonitrile-butadienestyrene (ABS), high-impact polystyrene (HIPS), and polyvinyl chloride (PVC)) in automobile shredder residue (ASR) to such an extent that their flotation ability is entirely depressed. Such a hydrophilization treatment also stimulates the ABS, HIPS, and PVC surface roughness, wetting of the surface, and the thermodynamic equilibrium conditions at the surface and ultimately changes surface polarity. SEM-EDS, AFM, and XPS analyses of the PVC and ABS surfaces demonstrated a marked decrease in [Cl/Br] and a significant increase in the number of hydrophilic groups, such as C-O, C=O, and (C=O)-O. Under froth flotation conditions at 50 rpm, about 99.5 % of ABS and 99.5 % of HIPS in ASR samples settled out, resulting in a purity of 98 and 98.5 % for ABS and HIPS in ASR samples, respectively. Furthermore, at 150 rpm, we also obtained 100 % PVC separation in the settled fraction, with 98 % purity in ASR. Total recovery of non-B/CFR-containing plastics reached nearly 100 % in the floating fraction. The amount of nano-Fe/Ca/CaO reagent employed during ozonation is very small, and additional removal of surface contaminants from the recycled ASR plastic surfaces by ozonation makes the developed process simpler, greener, and more effective.

  3. Simple fecal flotation is a superior alternative to guadruple Kato Katz smear examination for the detection of hookworm eggs in human stool.

    Directory of Open Access Journals (Sweden)

    Tawin Inpankaew

    2014-12-01

    Full Text Available Microscopy-based identification of eggs in stool offers simple, reliable and economical options for assessing the prevalence and intensity of hookworm infections, and for monitoring the success of helminth control programs. This study was conducted to evaluate and compare the diagnostic parameters of the Kato-Katz (KK and simple sodium nitrate flotation technique (SNF in terms of detection and quantification of hookworm eggs, with PCR as an additional reference test in stool, collected as part of a baseline cross-sectional study in Cambodia.Fecal samples collected from 205 people in Dong village, Rovieng district, Preah Vihear province, Cambodia were subjected to KK, SNF and PCR for the detection (and in case of microscopy-based methods, quantification of hookworm eggs in stool. The prevalence of hookworm detected using a combination of three techniques (gold standard was 61.0%. PCR displayed a highest sensitivity for hookworm detection (92.0% followed by SNF (44.0% and quadruple KK smears (36.0% compared to the gold standard. The overall eggs per gram feces from SNF tended to be higher than for quadruple KK and the SNF proved superior for detecting low egg burdens.As a reference, PCR demonstrated the higher sensitivity compared to SNF and the quadruple KK method for detection of hookworm in human stool. For microscopic-based quantification, a single SNF proved superior to the quadruple KK for the detection of hookworm eggs in stool, in particular for low egg burdens. In addition, the SNF is cost-effective and easily accessible in resource poor countries.

  4. Simple fecal flotation is a superior alternative to guadruple Kato Katz smear examination for the detection of hookworm eggs in human stool.

    Science.gov (United States)

    Inpankaew, Tawin; Schär, Fabian; Khieu, Virak; Muth, Sinuon; Dalsgaard, Anders; Marti, Hanspeter; Traub, Rebecca J; Odermatt, Peter

    2014-12-01

    Microscopy-based identification of eggs in stool offers simple, reliable and economical options for assessing the prevalence and intensity of hookworm infections, and for monitoring the success of helminth control programs. This study was conducted to evaluate and compare the diagnostic parameters of the Kato-Katz (KK) and simple sodium nitrate flotation technique (SNF) in terms of detection and quantification of hookworm eggs, with PCR as an additional reference test in stool, collected as part of a baseline cross-sectional study in Cambodia. Fecal samples collected from 205 people in Dong village, Rovieng district, Preah Vihear province, Cambodia were subjected to KK, SNF and PCR for the detection (and in case of microscopy-based methods, quantification) of hookworm eggs in stool. The prevalence of hookworm detected using a combination of three techniques (gold standard) was 61.0%. PCR displayed a highest sensitivity for hookworm detection (92.0%) followed by SNF (44.0%) and quadruple KK smears (36.0%) compared to the gold standard. The overall eggs per gram feces from SNF tended to be higher than for quadruple KK and the SNF proved superior for detecting low egg burdens. As a reference, PCR demonstrated the higher sensitivity compared to SNF and the quadruple KK method for detection of hookworm in human stool. For microscopic-based quantification, a single SNF proved superior to the quadruple KK for the detection of hookworm eggs in stool, in particular for low egg burdens. In addition, the SNF is cost-effective and easily accessible in resource poor countries.

  5. Characterization of Halomonas sp. ZM3 isolated from the Zelazny Most post-flotation waste reservoir, with a special focus on its mobile DNA.

    Science.gov (United States)

    Dziewit, Lukasz; Pyzik, Adam; Matlakowska, Renata; Baj, Jadwiga; Szuplewska, Magdalena; Bartosik, Dariusz

    2013-03-14

    Halomonas sp. ZM3 was isolated from Zelazny Most post-flotation mineral waste repository (Poland), which is highly contaminated with heavy metals and various organic compounds. Mobile DNA of the strain (i.e. plasmids and transposons) were analyzed in order to identify genetic information enabling adaptation of the bacterium to the harsh environmental conditions. The analysis revealed that ZM3 carries plasmid pZM3H1 (31,370 bp), whose replication system may be considered as an archetype of a novel subgroup of IncU-like replicons. pZM3H1 is a narrow host range, mobilizable plasmid (encodes a relaxase of the MOBV family) containing mercury resistance operon (mer) and czcD genes (mediate resistance to zinc and cobalt), which are part of a large truncated Tn3 family transposon. Further analysis demonstrated that the phenotypes determined by the pZM3H1 resistance cassette are highly dependent on the host strain. In another strand of the study, the trap plasmid pMAT1 was employed to identify functional transposable elements of Halomonas sp. ZM3. Using the sacB positive selection strategy two insertion sequences were identified: ISHsp1 - representing IS5 group of IS5 family and ISHsp2 - a distinct member of the IS630 family. This study provides the first detailed description of mobile DNA in a member of the family Halomonadaceae. The identified IncU plasmid pZM3H1 confers resistance phenotypes enabling adaptation of the host strain to the Zelazny Most environment. The extended comparative analysis has shed light on the distribution of related IncU plasmids among bacteria, which, in many cases, reflects the frequency and direction of horizontal gene transfer events. Our results also identify plasmid-encoded modules, which may form the basis of novel shuttle vectors, specific for this group of halophilic bacteria.

  6. The role of algal organic matter in the separation of algae and cyanobacteria using the novel "Posi" - Dissolved air flotation process.

    Science.gov (United States)

    Hanumanth Rao, Narasinga Rao; Yap, Russell; Whittaker, Michael; Stuetz, Richard M; Jefferson, Bruce; Peirson, William L; Granville, Anthony M; Henderson, Rita K

    2018-03-01

    Algae and cyanobacteria frequently require separation from liquid media in both water treatment and algae culturing for biotechnology applications. The effectiveness of cell separation using a novel dissolved air flotation process that incorporates positively charged bubbles (PosiDAF) has recently been of interest but has been shown to be dependent on the algae or cyanobacteria species tested. Previously, it was hypothesised that algal organic matter (AOM) could be impacting the separation efficiency. Hence, this study investigates the influence of AOM on cell separation using PosiDAF, in which bubbles are modified using a commercially available cationic polyelectrolyte poly(N, N-diallyl-N,N-dimethylammonium chloride) (PDADMAC). The separation of Chlorella vulgaris CS-42/7, Mychonastes homosphaera CS-556/01 and two strains of Microcystis aeruginosa (CS-564/01 and CS-555/1), all of which have similar cell morphology but different AOM character, was investigated. By testing the cell separation in the presence and absence of AOM, it was determined that AOM enhanced cell separation for all the strains but to different extents depending on the quantity and composition of carbohydrates and proteins in the AOM. By extracting AOM from the strain for which optimal separation was observed and adding it to the others, cell separation improved from 90%. This was attributed to elevated levels of acidic carbohydrates as well as glycoprotein-carbohydrate conjugations, which in turn were related to the nature and quantity of proteins and carbohydrates present in the AOM. Therefore, it was concluded that process optimisation requires an in-depth understanding of the AOM and its components. If culturing algae for biotechnology applications, this indicates that strain selection is not only important with respect to high value product content, but also for cell separation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Vacúolos de gás e flutuação em Difflugia mitriformis Wallich (Protista, Rhizopoda, Testaceolobosea Gas vacuoles and flotation in Diffugia mitriformis Wallich (Protista, Rhizopoda, Testaceolobosea

    Directory of Open Access Journals (Sweden)

    Vladimir Stolzenberg Torres

    1996-01-01

    Full Text Available The natural formation of gas vacuoles as a method of locomotion is described for Difflugia mitriformis Wallich, 1984. These vacuoles may contain different compositions of gases, basicly carbodioxyde or oxigen, with a membranous limitation similar or identical to other types of vacuoles. Those vacuoles are utilised by the organism as a mode of dislocation frorn the bottom to the water surface by flotation permiting better conditions for the survival of the individual, with the consequence of the perpetuance of the taxon.

  8. Central Diffraction at ALICE

    CERN Document Server

    Lämsä, Jerry W

    2011-01-01

    The ALICE experiment is shown to be well suited for studies of exclusive final states from central diffractive reactions. The gluon-rich environment of the central system allows detailed QCD studies and searches for exotic meson states, such as glueballs, hybrids and new charmonium-like states. It would also provide a good testing ground for detailed studies of heavy quarkonia. Due to its central barrel performance, ALICE can accurately measure the low-mass central systems with good purity. The efficiency of the Forward Multiplicity Detector (FMD) and the Forward Shower Counter (FSC) system for detecting rapidity gaps is shown to be adequate for the proposed studies. With this detector arrangement, valuable new data can be obtained by tagging central diffractive processes.

  9. Arsenic removal by using colloidal adsorption flotation utilizing Fe(OH)3 floc in a dissolved air flotation system; Eliminacion de arsenico mediante flotacion por adsorcion coloidal utilizando floculos de Fe(OH){sub 3} en un sistema de flotacion por aire disuelto

    Energy Technology Data Exchange (ETDEWEB)

    Pavez, O.; Palacios, J. M.; Aguilar, C.

    2009-07-01

    In the present work, the influence of Fe/As ratio on the As removal, from aqueous solutions, applying flotation by colloidal adsorption was studied. Ferric chloride was used as coagulant and dodec il sulfate as collector, and arsenic trioxide was utilized to preparing the solutions. The obtained results show that the highest arsenic removal was accomplished in the range of pH between 4 and 5,5, and the increasing of the initial concentration of Fe(III), increases the removal of arsenic from the solution. However, with the decreasing of the initial concentration of arsenic in the solution, it is required a larger Fe/As ratio for its removal. For solutions containing: 13,73, 1,71 and 0,105 mg/L of arsenic, it was shown that to remove around 95% of the dissolved arsenic, a Fe/As ratios of approximately 6/1, 18/1 and 800/1, respectively, are required. (Author) 31 refs.

  10. Homogeneous liquid-liquid extraction (HoLLE) via flotation combined with gas chromatography-flame ionization detection as a very simple, rapid and sensitive method for the determination of fenitrothion in water samples.

    Science.gov (United States)

    Mashayekhi, Hossein Ali

    2013-01-01

    Homogeneous liquid-liquid extraction via flotation assistance (HoLLE-FA) and gas chromatography-flame ionization detection (GC-FID) was presented for the extraction and determination of fenitrothion in water samples. In this work, a rapid, simple and efficient HoLLE-FA method was developed based on applying low-density organic solvents without employing centrifugation. A special extraction cell was designed to facilitate the collection of low-density solvent extraction in the determination of fenitrothion in water samples. The water sample solution was added into an extraction cell that contained an appropriate mixture of extraction and homogeneous solvents. By using air flotation, the organic solvent was collected at the conical part of the designed cell. Under the optimum conditions, the method performance was studied in terms of the linear dynamic range (LDR from 1.0 up to 100 μg L⁻¹), linearity (r² > 0.998), and precision (repeatability extraction and determination of fenitrothion in three different water samples.

  11. "Central Station" Londonis

    Index Scriptorium Estoniae

    2000-01-01

    Londoni galeriis Milch seitsme läti, leedu ja eesti kunstniku projekt "Central Station". Kuraatorid Lisa Panting, Sally Tallant. Eestist osalevad Hanno Soans (Catarina Campinoga koostöös valminud video), Kiwa, Kai Kaljo

  12. Central nervous system resuscitation

    DEFF Research Database (Denmark)

    McIntosh, T K; Garde, E; Saatman, K E

    1997-01-01

    Traumatic injury to the central nervous system induces delayed neuronal death, which may be mediated by acute and chronic neurochemical changes. Experimental identification of these injury mechanisms and elucidation of the neurochemical cascade following trauma may provide enhanced opportunities...

  13. Outsourcing central banking

    DEFF Research Database (Denmark)

    Khoury, Sarkis Joseph; Wihlborg, Clas

    2005-01-01

    The literature on Currency Boards (CB) stops at the water edge in terms of dealing with the totality of the functions of a central bank. Monetary policy, and banking supervisioncan be "outsourced" in an open economy with substantial foreign direct investment (FDI)in the banking sector if political...... nationalism does not trump economic rationality. An orthodox CB renders the central banking function redundant in terms of interest rate and exchange rate determination. FDI in banking could perform the same role for the supervisory function of central banks. We use the case of Estonia to illustrate...... the feasibility of, and constraints on, outsourcing of central bank functions. A brief discussion of the Argentinian experience is used for contrast.Key words: Currency Board, Foreign Banks, Supervision, Regional Integration,outsourcing....

  14. Central nervous system

    Science.gov (United States)

    The central nervous system is composed of the brain and spinal cord. Your brain and spinal cord serve as the main "processing center" for your entire nervous system. They control all the workings of your body.

  15. Isolated central vestibular syndrome.

    Science.gov (United States)

    Kim, Sung-Hee; Park, Seong-Ho; Kim, Hyo-Jung; Kim, Ji-Soo

    2015-04-01

    Isolated vestibular syndrome may occur all along the vestibular pathways from the peripheral labyrinth to the brain. By virtue of recent developments in clinical neurotology and neuroimaging, however, diagnosis of isolated central vestibulopathy is increasing. Here, we review five distinct syndromes of isolated central vestibular syndrome from lesions restricted to the vestibular nuclei, the nucleus prepositus hypoglossi, the flocculus, the tonsil, and the nodulus, and introduce a new vestibular syndrome from isolated involvement of the inferior cerebellar peduncle. Decreased responses to head impulses do not exclude a central lesion as a cause of isolated vestibular syndrome. Brain imaging, including diffusion-weighted magnetic resonance imaging (MRI), may be falsely negative during the acute phase in patients with isolated vestibular syndrome because of a stroke. Central signs should be sought carefully in patients with isolated vertigo, even when the patients show the features of peripheral vestibulopathy and negative MRIs. Recognition of these isolated central vestibular syndromes would aid in defining the lesions responsible for various vestibular manifestations in central vestibulopathy. © 2015 New York Academy of Sciences.

  16. Obtention of high purity silica from the flotation waste of itabiritic ore; Obtencao de silica de elevada pureza a partir do rejeito de flotacao de um minerio itabiritico

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Polyana Fabricia Fernandes

    2016-10-01

    Banded iron formations are exploited as iron mineral in 'Quadrilatero Ferrifero' of Minas Gerais (MG) State, Brazil. About half of the amount of extracted material becomes tailings, which are stored in tailing dams or used for filling mining pits. Tens of thousands of tons are generated daily in operating mines in this region, causing concern about the environmental liabilities, and costs to manage the tailing dams. Miners are committed to finding uses for these wastes in other productive chains. This thesis aimed to obtain high purity silica from the flotation tailings of banded iron formations using classical techniques for ore processing, such as particle size classification and magnetic separation, followed by hydrometallurgical leaching, also alkaline fusion and chemical precipitation. The tailings samples was collected in the tailings dam of Peak Mine operated by Vale A.S., in Itabirito – MG. This sample had initially 33.4% by weight SiO{sub 2}, 57.4% wt Fe{sub 2}O{sub 3} and 8.31% wt Al{sub 2}O{sub 3}. After desliming for disposal of the fine particles (-37μm) the composition was 68.0% SiO{sub 2}, 31.4% Fe{sub 2}O{sub 3} and 0.50% Al{sub 2}O{sub 3}. After magnetic separation, the composition was 93.8% SiO{sub 2}, 1.16% Fe{sub 2}O{sub 3} and 3.80% Al{sub 2}O{sub 3}. After acid leaching l or digestion to remove impurities, it was possible to obtain silica with 98% purity. The fusion with sodium hydroxide, followed by alkaline leaching of sodium silicate and silica precipitation gave purities of about 99.5%. Values even higher may be possible with optimization of the parameters of alkaline fusion or by repeating the process from the product with purity of 99.5%. The iron oxide content and the aluminum main contaminants were 0.01% and 0.07%, respectively. Amorphous silica was obtained with high specific surface (322 m{sup 2}/g) and particle size less than 200 nm. Depending on the application, a control should be made for the impurities, such as

  17. Hydroxamic acid interactions with solvated cerium hydroxides in the flotation of monazite and bastnäsite—Experiments and DFT study

    Energy Technology Data Exchange (ETDEWEB)

    Sarvaramini, A., E-mail: amin.sarvaramini.1@ulaval.ca; Azizi, D., E-mail: dariush.azizi.1@ulaval.ca; Larachi, F., E-mail: faical.larachi@gch.ulaval.ca

    2016-11-30

    Highlights: • Experimental and DFT studies of hydroxamic acid adsorption on monazite and bastnäsite. • Highest bastnäsite and monazite floatability observed at pH 7–9. • First solvation layer of cerium hydroxides consisted of up to 10 water molecules. • Solvated Ce(OH){sub 2}{sup +} and Ce(OH){sup 2+} cations interact with up to 3 collector anions. • Interaction of zero-charge solvated Ce(OH){sub 3} involves up to 2 collector anions. - Abstract: Density functional theory (DFT) simulations and experiments were performed to clarify the interaction mechanisms between hydroxamic acid collectors and cerium hydroxides during the flotation of bastnäsite and monazite minerals. These minerals showed considerable floatability at moderately alkaline pH which was related to the adsorption of hydroxamic acids on their surfaces as confirmed by vibrational spectroscopic and zeta potential measurements. DFT simulations showed that at moderately alkaline pH, the interactions between solvated Ce(OH){sup 2+} and Ce(OH){sub 2}{sup +} and heptyl-hydroxamic acid (HHA) anions resulted in the formation of, respectively, [Ce(OH)(HHA){sub x}(H{sub 2}O){sub y}]{sup 2−x} (x[y = ] = 1[6],2[3],3[1]) and [Ce(OH){sub 2}(HHA){sub x}(H{sub 2}O){sub y}]{sup 1−x} (x[y = ] = 1[5],2[1],3[0]) complexes. The collector anions were found to interact directly through formation of two covalent bonds between their two polar-head oxygen atoms and cerium in the hydroxide complexes. However, formation of such new bonds resulted in breakage of a few covalent/electrostatic bonds between cerium and water molecules initially present in the first hydration shell of the rare-earth metal cation. Building up in the electric double layer of the semi-soluble minerals, these complexes, and by extension, those from other rare-earth elements belonging to monazite and bastnäsite, are speculated to play a role in the interactions between rare-earth minerals and hydroxamic acid collectors.

  18. Aflatoxins, discolouration and insect damage in dried cowpea and pigeon pea in Malawi and the effectiveness of flotation/washing operation in eliminating the aflatoxins.

    Science.gov (United States)

    Matumba, Limbikani; Singano, Lazarus; Pungulani, Lawrent; Mvula, Naomi; Matumba, Annie; Singano, Charles; Matita, Grey

    2017-05-01

    Aflatoxin contamination and biodeterioration were examined in 302 samples of dry cowpeas and pigeon peas that were randomly purchased from 9 districts of the Southern Region of Malawi during July and November 2015. Further, the impact of flotation/washing on aflatoxin levels on the pulses was elucidated. Aflatoxin analyses involved immunoaffinity column (IAC) clean-up and HPLC quantification with fluorescence detection (FLD) while legume biodeterioration assessments were done by visual inspection. Aflatoxins were frequently detected in cowpea (24%, max., 66 μg/kg) and pigeon pea (22%, max., 80 μg/kg) samples that were collected in the month of July. Lower aflatoxin incidence of 15% in cowpeas (max., 470 μg/kg) and 14% in pigeon peas (max., 377 μg/kg) was recorded in the November collection. Overall, aflatoxin levels were significantly higher in the pulses that were collected in November. However, there were no significant differences in the total aflatoxin (aflatoxin B 1 (AFB 1 ) + AFB 2 + AFG 1 + AFG 2 ) levels between the two types of pulses. Remarkably, in 76.2% of the aflatoxin positive cowpea and in 41.7% of the aflatoxin positive pigeon pea samples, aflatoxin G 1 concentration exceeded aflatoxin B 1. Insect damage percentage averaged at 18.1 ± 18.2% (mean ± SD) in the cowpeas and 16.1 ± 19.4% in pigeon peas. Mean discolouration percentage (number of pulses) of the cowpeas and pigeon peas was found to be at 6.7 ± 4.9 and 8.7 ± 6.2%, respectively. Washing and discarding the buoyant fraction was highly efficient in reducing aflatoxin levels; only 5.2 ± 11.1% of the initial aflatoxin level was found in the cleaned samples. In conclusion, cowpeas and pigeon peas sold on the local market in Malawi may constitute a hazard especially if floatation/washing step is skipped.

  19. Colloquium on Central Asia

    International Nuclear Information System (INIS)

    2005-01-01

    This colloquium on Azerbaijan was organized by the direction of international relations of the French Senate and the French center of foreign trade (CFCE). This document gathers the interventions of the participants and the debates with the audience following these interventions. The topics treated concern: - the present day political-economical situation of Central Asia countries (problem of borders, relations with Russia and China); - the economies of Central Asia countries: short term problems and medium-term perspectives; - the relations with the European Union (political, economical, trade and investments, perspectives); - the European energy stakes of Caspian sea (oil and gas reserves, development of hydrocarbon resources, exploitation and transport constraints, stakes for Europe and France); - TotalFinaElf company in Central Asia (Kazakhstan, Azerbaijan, enclavement problem); - the economical impacts of the TRACECA pathway (Transport Corridor Europe Caucasus Asia). (J.S.)

  20. The Naive Central Banker

    Directory of Open Access Journals (Sweden)

    Marcelo de Carvalho Griebeler

    2015-09-01

    Full Text Available There has been in some countries a trend of assigning other functions to central banks besides price stability. The most suggested function to be added to monetary authority’s obligations is to pursue economic growth or full employment. In this paper we characterize the behavior and analyse the optimal monetary policy of, what we call, a naive central banker. We describe the naive behavior as one that does face the inflation-unemployment trade-off, but it tries to minimize both variables simultaneously. Our findings, both under discretion and commitment, indicate that the naive central banker delivers lower expected inflation and inflation variance than the benchmark behavior whenever the economy is rigid enough. However, the degree of conservativeness also affects this result, such that the less conservative the naive policymaker, the more rigidity is necessary.

  1. The central nervous system

    International Nuclear Information System (INIS)

    Holmes, R.A.

    1984-01-01

    The first section presents a comprehensive evaluation of radionuclide imaging of the central nervous system and provides a comparison of the detection accuracies of radionuclide imaging (RNI) and XCT in certain lesions, realizing that the XCT results may vary when radiocontrast or newer generation XCT scanners are used. Although conventional radionuclide imaging of the central nervous system has experienced no significant changes over the last 7 years except for mild refinements, a new section has been added on positron emission tomography (PET). Most positron radiopharmaceuticals passively cross the intact blood-brain barrier, and their localization has catalyzed renewed interest in our ability to metabolically study and obtain images of the central nervous system. The section on radionuclide cisternography has been rewritten to reflect present day practice and the wider application of XCT in describing conditions affecting the ventricular system

  2. Central pancreatectomy without anastomosis

    Directory of Open Access Journals (Sweden)

    Pahuja Anil

    2009-08-01

    Full Text Available Abstract Background Central pancreatectomy has a unique application for lesions in the neck of the pancreas. It preserves the distal pancreas and its endocrine functions. It also preserves the spleen. Methods This is a retrospective review of 10 patients who underwent central pancreatectomy without pancreatico-enteric anastomosis between October 2005 and May 2009. The surgical indications, operative outcomes, and pathologic findings were analyzed. Results All 10 lesions were in the neck of the pancreas and included: 2 branch intraductal papillary mucinous neoplasms (IPMNs, a mucinous cyst, a lymphoid cyst, 5 neuroendocrine tumors, and a clear cell adenoma. Conclusion Central pancreatectomy without pancreatico-enteric anastomosis for lesions in the neck and proximal pancreas is a safe and effective procedure. Morbidity is low because there is no anastomosis. Long term endocrine and exocrine function has been maintained.

  3. SOCRATES Invades Central Europe

    Directory of Open Access Journals (Sweden)

    Joseph Slowinski

    1998-04-01

    Full Text Available The objective of this article is to explore the current reality faced by higher education students in Central and Eastern Europe and to draw out the implications of this current reality for policy makers in the future. In the article, I explore the influence of transnational corporations' training programs on education as it currently pertains to Central and Eastern European higher education and employment. In addition, multinational corporate entities exercise influence on European Union policy through the role of lobby organizations and activities. I explore the influence of these practices on education with an emphasis on the emerging importance of Western language skills. In addition, I focus on the European Union and its efforts to expand into Central and Eastern Europe in order to provide a focal point for analysis.

  4. Central Bank independence

    Directory of Open Access Journals (Sweden)

    Vasile DEDU

    2012-08-01

    Full Text Available In this paper we present the key aspects regarding central bank’s independence. Most economists consider that the factor which positively influences the efficiency of monetary policy measures is the high independence of the central bank. We determined that the National Bank of Romania (NBR has a high degree of independence. NBR has both goal and instrument independence. We also consider that the hike of NBR’s independence played an important role in the significant disinflation process, as headline inflation dropped inside the targeted band of 3% ± 1 percentage point recently.

  5. Atmospheres of central stars

    International Nuclear Information System (INIS)

    Hummer, D.G.

    1978-01-01

    The author presents a brief summary of atmospheric models that are of possible relevance to the central stars of planetary nebulae, and then discusses the extent to which these models accord with the observations of both nebulae and central stars. Particular attention is given to the significance of the very high Zanstra temperature implied by the nebulae He II lambda 4686 A line, and to the discrepancy between the Zanstra He II temperature and the considerably lower temperatures suggested by the appearance of the visual spectrum for some of these objects. (Auth.)

  6. Centralized mouse repositories.

    Science.gov (United States)

    Donahue, Leah Rae; Hrabe de Angelis, Martin; Hagn, Michael; Franklin, Craig; Lloyd, K C Kent; Magnuson, Terry; McKerlie, Colin; Nakagata, Naomi; Obata, Yuichi; Read, Stuart; Wurst, Wolfgang; Hörlein, Andreas; Davisson, Muriel T

    2012-10-01

    Because the mouse is used so widely for biomedical research and the number of mouse models being generated is increasing rapidly, centralized repositories are essential if the valuable mouse strains and models that have been developed are to be securely preserved and fully exploited. Ensuring the ongoing availability of these mouse strains preserves the investment made in creating and characterizing them and creates a global resource of enormous value. The establishment of centralized mouse repositories around the world for distributing and archiving these resources has provided critical access to and preservation of these strains. This article describes the common and specialized activities provided by major mouse repositories around the world.

  7. Gastrointestinal protists and helminths of habituated agile mangabeys (Cercocebus agilis) at Bai Hokou, Central African Republic.

    Science.gov (United States)

    Pafčo, Barbora; Tehlárová, Zuzana; Jirků Pomajbíková, Kateřina; Todd, Angelique; Hasegawa, Hideo; Petrželková, Klára J; Modrý, David

    2018-02-01

    Infectious diseases including those caused by parasites can be a major threat to the conservation of endangered species. There is thus a great need for studies describing parasite infections of these species in the wild. Here we present data on parasite diversity in an agile mangabey (Cercocebus agilis) group in Bai Hokou, Dzanga-Sangha Protected Areas (DSPA), Central African Republic. We coproscopically analyzed 140 mangabey fecal samples by concentration techniques (flotation and sedimentation). Agile mangabeys hosted a broad diversity of protistan parasites/commensals, namely amoebas (Entamoeba spp., Iodamoeba buetschlli), a Buxtonella-like ciliate and several parasitic helminths: strongylid and spirurid nematodes, Primasubulura sp., Enterobius sp., and Trichuris sp. Importantly, some of the detected parasite taxa might be of potential zoonotic importance, such as Entamoeba spp. and the helminths Enterobius sp., Trichuris sp., and strongylid nematodes. Detailed morphological examination of ciliate cysts found in mangabeys and comparison with cysts of Balantioides coli from domestic pigs showed no distinguishing structures, although significant differences in cyst size were recorded. Scanning or transmission electron microscopy combined with molecular taxonomy methods are needed to properly identify these ciliates. Further studies using molecular epidemiology are warranted to better understand cross-species transmission and the zoonotic potential of parasites in sympatric non-human primates and humans cohabiting DSPA. © 2018 Wiley Periodicals, Inc.

  8. Multicultural Central Asia.

    Science.gov (United States)

    Boyle, Eric D.

    This article addresses the multicultural aspect of Central Asia in response to the discussion on diversity in U.S. classrooms. Many areas of the world are more diverse than the U.S., and these areas experience successes and failures with many of the same issues the U.S. is currently struggling with. Comparing the U.S. diversity debate with similar…

  9. Testing for central symmetry

    NARCIS (Netherlands)

    Einmahl, John; Gan, Zhuojiong

    Omnibus tests for central symmetry of a bivariate probability distribution are proposed. The test statistics compare empirical measures of opposite regions. Under rather weak conditions, we establish the asymptotic distribution of the test statistics under the null hypothesis; it follows that they

  10. Central American Climatology

    Science.gov (United States)

    1985-04-01

    Central America, as where mean temperatures are relatively warm throughout the year de- so spite seasonal rainfall changes. 75 Elevation, solar angle...November 1982 Control Hidalgo Anos.1952-1963, Republica de Nicaragua, Ministerio de Formento Y O0.PP, Comision Nacional de Energia . Craig, Richard A., The

  11. Central Dogma Goes Digital.

    Science.gov (United States)

    Lin, Yihan; Elowitz, Michael B

    2016-03-17

    In this issue of Molecular Cell, Tay and colleagues (Albayrak et al., 2016) describe a new technique to digitally quantify the numbers of protein and mRNA in the same mammalian cell, providing a new way to look at the central dogma of molecular biology. Copyright © 2016 Elsevier Inc. All rights reserved.

  12. A centrality detector concept

    Energy Technology Data Exchange (ETDEWEB)

    Tarafdar, Sourav; Citron, Zvi; Milov, Alexander, E-mail: alexander.milov@weizmann.ac.il

    2014-12-21

    The nucleus–nucleus impact parameter and collision geometry of a heavy ion collision are typically characterized by assigning a collision “centrality”. In all present heavy ion experiments centrality is measured indirectly, by detecting the number of particles or the energy of the particles produced in the interactions, typically at high rapidity. Centrality parameters are associated to the measured detector response using the Glauber model. This approach suffers from systematic uncertainties related to the assumptions about the particle production mechanism and limitations of the Glauber model. In the collider based experiments there is a unique possibility to measure centrality parameters by registering spectator fragments remaining from the collision. This approach does not require model assumptions and relies on the fact that spectators and participants are related via the total number of nucleons in the colliding species. This paper describes the concept of a centrality detector for heavy ion experiment, which measures the total mass number of all fragments by measuring their deflection in the magnetic field of the collider elements.

  13. Central Serous Retinopathy Treatment

    Science.gov (United States)

    ... under the RPE. As a result, a small detachment forms under the retina, causing vision to become distorted. This image from ... a blister-like swelling in layers of the retina. Central serous chorioretinopathy usually affects just one ... is retinal detachment for people with high myopia? Mar 29, 2017 ...

  14. Central Cord Syndrome

    Science.gov (United States)

    ... finding better ways to prevent, treat, and ultimately cure neurological disorders such as central cord syndrome. Information from the National Library of Medicine’s MedlinePlus Spinal ... cord syndrome is the most common form of incomplete spinal cord injury characterized by impairment in the arms and hands and to a lesser extent in the legs. ...

  15. Flotation of agent for breach of emulsion oil/water aiming treatment of water produced for the industry petroleum; Agente de flotacao (Tanfloc) para quebra de emulsao oleo/agua visando tratamento de aguas produzidas pela industria do petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, A.C. de; Andrade, J.M. de; Melo, M.A.A.; Melo, D.M.A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2008-07-01

    This work was studied the action of an agent of flotation TanFloc broken emulsion in oil / water when its concentration varies and salinity. This material is used by Petroleum brazilian for removal of turbidity in the water from the petroleum industry. For the test set up a bench in the laboratory of the Environmental Technology UFRN for simulation of tests made on the field. To do so, was studied the concentration of TanFloc and it was found that the best concentration for removal of turbidity was 11ppm such material. It was found that the level of salinity affects particularly the results of turbidity therefore this was also one of the parameters studied. (author)

  16. ASSESSMENT OF THE PRESENCE OF Toxocara EGGS IN SOILS OF AN ARID AREA IN CENTRAL-WESTERN ARGENTINA

    Directory of Open Access Journals (Sweden)

    María Viviana Bojanich

    2015-02-01

    Full Text Available With the aim of studying the contamination of soils with eggs of Toxocara spp. in an arid area in the central-western region of Argentina, 76 soil samples were collected from 18 towns belonging to six provinces of central-western Argentina. They were processed by the centrifugal flotation method. No eggs of Toxocara spp. were found. It can be concluded that the negative results are directly related to the characteristics of the environment and climate present in the studied area. The finding of eggs in soils depends on several factors: the presence of canine or feline feces, the hygienic behavior of pet owners, the presence of stray animals without veterinary supervision, the weather and environmental conditions, and laboratory techniques used; and all these circumstances must be considered when comparing the results found in different geographical regions. In order to accurately define the importance of public spaces in the transmission of infection to humans, it is important to consider the role of backyards or green spaces around housing in small towns, where the population is not used to walking pets in public spaces, and in such cases a significant fraction of the population may acquire the infection within households.

  17. Spent fuel centralized storage

    International Nuclear Information System (INIS)

    Chometon, P.L.

    1985-01-01

    Nuclear energy producer countries have felt the need to build a centralized spent fuel storage before reprocessing (for example, COGEMA in FRANCE), either in an adjoining plant on an appropriate site, or isolated. More rarely, this storage enables to decide whether to reprocess or to definitely store spent fuel considered as being waste: for example CLAB in Sweden. Our Company is specialized in the design and construction of spent fuel centralized storage plants. Storage generally takes place in a pool in order to facilitate handling operations and retrieving of these fuels, but these operations may also be effected in a dry way, either in concrete structures or in storage casks. With respect to pools, which might currently be the most appropriate and flexible system, several improvements have recently been made in the design of cask reception facilities and spent fuel storage. These improvements are presented, hereafter [fr

  18. Spent fuel centralized storage

    International Nuclear Information System (INIS)

    Baillif, L.; Chometon, P.L.

    1986-01-01

    Nuclear energy producer countries have felt the need to build a centralized spent fuel storage before reprocessing, either in an adjoining plant on an appropriate site, or isolated. More rarely, this storage enables to decide whether to reprocess or to definitely store spent fuel considered as being waste: for example CLAB in Sweden. Our Company SGN is specialized among others in the design and construction of spent fuel centralized storage plants. Storage generally takes place in a pool in order to facilitate handling operations and retrieving of these fuels, but these operations may also be effected in a dry way, either in concrete structures or in storage casks. With respect to pools, which might currently be the most appropriate and flexible system, several improvements have recently been made in the design of cask reception facilities and spent fuel storage. These improvements are presented, hereafter [fr

  19. FNAL central email systems

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, Jack; Lilianstrom, Al; Pasetes, Ray; Hill, Kevin; /Fermilab

    2004-10-01

    The FNAL Email System is the primary point of entry for email destined for an employee or user at Fermilab. This centrally supported system is designed for reliability and availability. It uses multiple layers of protection to help ensure that: (1) SPAM messages are tagged properly; (2) All mail is inspected for viruses; and (3) Valid mail gets delivered. This system employs numerous redundant subsystems to accomplish these tasks.

  20. Centrally Banked Cryptocurrencies

    OpenAIRE

    Danezis, G.; Meiklejohn, S.

    2016-01-01

    Current cryptocurrencies, starting with Bitcoin, build a decentralized blockchain-based transaction ledger, maintained through proofs-of-work that also serve to generate a monetary supply. Such decentralization has benefits, such as independence from national political control, but also significant limitations in terms of computational costs and scalability. We introduce RSCoin, a cryptocurrency framework in which central banks maintain complete control over the monetary supply, but rely on...

  1. Central osteosclerosis with trichothiodystrophy

    International Nuclear Information System (INIS)

    Wakeling, Emma L.; Brady, Angela F.; Cruwys, Michele; Suri, Mohnish; Aylett, Sarah E.; Hall, Christine

    2004-01-01

    Trichothiodystrophy (TTD) is a rare, autosomal recessive, multisystem disorder associated with defects in nucleotide excision repair. We report a 7-year-old boy with TTD due to mutation in the XPD gene. The patient has classic features of this condition, including brittle, sulphur-deficient hair, ichthyosis, growth retardation and developmental delay. In addition, he has radiological evidence of progressive central osteosclerosis. Although similar radiological findings have previously been reported in a small number of patients, this association is not widely recognised. We review the radiological findings in this and other similar cases and discuss the natural history of these bony changes. (orig.)

  2. Central osteosclerosis with trichothiodystrophy

    Energy Technology Data Exchange (ETDEWEB)

    Wakeling, Emma L.; Brady, Angela F. [North West Thames Regional Genetics Service, Kennedy-Galton Centre, Level 8 V, North West London Hospitals NHS Trust, Watford Road, HAI 3UJ, Harrow, Middlesex (United Kingdom); Cruwys, Michele [Department of Paediatrics, Hillingdon Hospital, Hillingdon, Middlesex (United Kingdom); Suri, Mohnish [Clinical Genetics Service, City Hospital, Nottingham (United Kingdom); Aylett, Sarah E. [Neurosciences Unit, Great Ormond Street Hospital for Children NHS Trust, London (United Kingdom); Hall, Christine [Department of Radiology, Great Ormond Street Hospital for Children NHS Trust, London (United Kingdom)

    2004-07-01

    Trichothiodystrophy (TTD) is a rare, autosomal recessive, multisystem disorder associated with defects in nucleotide excision repair. We report a 7-year-old boy with TTD due to mutation in the XPD gene. The patient has classic features of this condition, including brittle, sulphur-deficient hair, ichthyosis, growth retardation and developmental delay. In addition, he has radiological evidence of progressive central osteosclerosis. Although similar radiological findings have previously been reported in a small number of patients, this association is not widely recognised. We review the radiological findings in this and other similar cases and discuss the natural history of these bony changes. (orig.)

  3. Central nervous system tumors

    International Nuclear Information System (INIS)

    Curran, W.J. Jr.

    1991-01-01

    Intrinsic tumors of the central nervous system (CNS) pose a particularly challenging problem to practicing oncologists. These tumors rarely metastasize outside the CNS, yet even histologically benign tumors can be life-threatening due to their local invasiveness and strategic location. The surrounding normal tissues of the nervous system is often incapable of full functional regeneration, therefore prohibiting aggressive attempts to use either complete surgical resection or high doses of irradiation. Despite these limitations, notable achievements have recently been recorded in the management of these tumors

  4. Central Hypothyroidism in Miniature Schnauzers

    NARCIS (Netherlands)

    Voorbij, Annemarie M W Y; Leegwater, Peter A J; Buijtels, Jenny J C W M; Daminet, Sylvie; Kooistra, Hans S

    2016-01-01

    BACKGROUND: Primary hypothyroidism is a common endocrinopathy in dogs. In contrast, central hypothyroidism is rare in this species. OBJECTIVES: The objective of this article is to describe the occurrence and clinical presentation of central hypothyroidism in Miniature Schnauzers. Additionally, the

  5. Central ignition scenarios for TFTR

    Energy Technology Data Exchange (ETDEWEB)

    Zweben, S.J.; Redi, M.H.; Bateman, G.

    1986-03-01

    The possibility of obtaining ignition in TFTR by means of very centrally peaked density profiles is examined. It is shown that local central alpha heating can be made to exceed local central energy losses (''central ignition'') under global conditions for which Q greater than or equal to 1. Time dependent 1-D transport simulations show that the normal global ignition requirements are substantially relaxed for plasmas with peaked density profiles. 18 refs., 18 figs.

  6. Central Banking after the Crisis

    OpenAIRE

    Frederick S. Mishkin

    2013-01-01

    This paper explores where central banking is heading after the recent financial crisis. First it discusses the central bank consensus before the crisis and then outlines the key facts learned from the crisis that require changes in the way central banks conduct their business. Finally, it discusses four main areas in which central banks are altering their policy frameworks: 1) the interaction between monetary and financial stability policies, 2) nonconventional monetary policy, 3) risk manage...

  7. Central ignition scenarios for TFTR

    International Nuclear Information System (INIS)

    Zweben, S.J.; Redi, M.H.; Bateman, G.

    1986-03-01

    The possibility of obtaining ignition in TFTR by means of very centrally peaked density profiles is examined. It is shown that local central alpha heating can be made to exceed local central energy losses (''central ignition'') under global conditions for which Q greater than or equal to 1. Time dependent 1-D transport simulations show that the normal global ignition requirements are substantially relaxed for plasmas with peaked density profiles. 18 refs., 18 figs

  8. Alpha current flow betweenness centrality

    NARCIS (Netherlands)

    Avrachenkov, K.; Litvak, Nelli; Medyanikov, V.; Sokol, M.

    2013-01-01

    A class of centrality measures called betweenness centralities reflects degree of participation of edges or nodes in communication between different parts of the network. The original shortest-path betweenness centrality is based on counting shortest paths which go through a node or an edge. One of

  9. The central Iowa project.

    Science.gov (United States)

    Allen, H M

    1994-10-01

    This project developed and tested a population-based survey, the HS Form, to examine health and health care in the Central Iowa community. Data from this new collection of proven sets of items were used to compare competing health plans, doctor offices, hospitals, and to develop preliminary norms of the community's insured, in two areas: system performance and health burden. The results showed that the survey: (1) was both feasible and efficient in delivering a comprehensive and generic assessment of consumers and patients; (2) revealed consistent, noteworthy differences between plans and between providers across both sets of criteria; and (3) indicated that there is substantial room for improvement in Central Iowa's health care delivery system from the public's perspective. Recommendations for next steps include: (1) following through on the June 1993 community forum (held to discuss the project's methods and results with local decision makers); (2) broadening the evaluation design to increase sample representativeness; and (3) implementing a pre/post approach to measure changes in plan and provider performance.

  10. Central pain control.

    Science.gov (United States)

    Calvino, Bernard; Grilo, Rose Marie

    2006-01-01

    We describe the anatomic and physiological components involved in pain physiology, with the goal of providing readers with the background information needed to understand central pain control mechanisms. These include spinal segmental controls, supraspinal excitatory and inhibitory controls, and diffuse noxious inhibitory controls (DNICs). Pain is a subjective sensation produced by an emotionally unpleasant experience considered to originate in adaptive processes taking place within neuron networks located at various levels of the central nervous system. The intensity of the components of pain is influenced by the stimulus characteristics, patient-related factors, and the setting in which the stimulus occurs. The various components of pain and the psychological and neurophysiological mechanisms that underlie the affective dimension of pain are reviewed. As a conclusion, phantom pain is used to illustrate the role for physiological systems independent from those involved in the physiology of nociception and pain, such as the motor cortex. This example highlights the extreme complexity of pain and pain control systems in humans.

  11. Orden monetario y bancos centrales Monetary order and Central Banks

    Directory of Open Access Journals (Sweden)

    Aglietta Michel

    1996-06-01

    Full Text Available Con el enfoque evolucionista e institucionalista de la economía de las convenciones francesa, este trabajo analiza el surgimiento histórico de la banca central y la creación institucional del 'arte de la banca central'. El artículo estudia los modelos formales del orden monetario, la banca libre y la banca central, y analiza los eventos históricos que llevaron a que el Banco de Inglaterra inventara el arte de manejar los bancos centrales en conjunción con el aprendizaje colectivo e institucional que lo hizo posible. Aglietta muestra que la banca central no es una creación del Estado sino una creación institucional endógena al sistema de mercado.With the evolutionist and institutionalist focus of the economics of the French conventions, this paper analyzes the historical rise of the central bank and the institutional creation of the 'art of the central bank'. The article studies formal models of the monetary order, free banking and the central bank, and analyzes the historie events that led to the Bank of England inventing the art of managing the central banks, in conjunction with the collective and institutional learning that made it possible. Aglietta shows that the central bank is not a creation of the State, but rather aninstitutional creation endogenous to the market system.

  12. UA2 central calorimeter

    CERN Document Server

    The UA2 central calorimeter measured the energy of individual particles created in proton-antiproton collisions. Accurate calibration allowed the W and Z masses to be measured with a precision of about 1%. The calorimeter had 24 slices like this one, each weighing 4 tons. The slices were arranged like orange segments around the collision point. Incoming particles produced showers of secondary particles in the layers of heavy material. These showers passed through the layers of plastic scintillator, generating light which was taken by light guides (green) to the data collection electronics. The amount of light was proportional to the energy of the original particle. The inner 23 cm of lead and plastic sandwiches measured electrons and photons; the outer 80 cm of iron and plastic sandwiches measured strongly interacting hadrons. The detector was calibrated by injecting light through optical fibres or by placing a radioactive source in the tube on the bottom edge.

  13. Central solar energy receiver

    Science.gov (United States)

    Drost, M. Kevin

    1983-01-01

    An improved tower-mounted central solar energy receiver for heating air drawn through the receiver by an induced draft fan. A number of vertically oriented, energy absorbing, fin-shaped slats are radially arranged in a number of concentric cylindrical arrays on top of the tower coaxially surrounding a pipe having air holes through which the fan draws air which is heated by the slats which receive the solar radiation from a heliostat field. A number of vertically oriented and wedge-shaped columns are radially arranged in a number of concentric cylindrical clusters surrounding the slat arrays. The columns have two mirror-reflecting sides to reflect radiation into the slat arrays and one energy absorbing side to reduce reradiation and reflection from the slat arrays.

  14. Central Station Design Options

    DEFF Research Database (Denmark)

    2011-01-01

    The purpose of EDISON Work Package 4.1 is the evaluation of possible Central (charging) Stations design options for making possible the public charging of Electric Vehicles (EVs). A number of scenarios for EVs are assessed, with special emphasis on the options of Fast Charging and Battery Swapping....... With the 3-phase AC quick charging options of 11, 22 kW and 43 kW, (IEC 62196, EN60038, EN 61851) both the Danish and Bornholm environments offer a good chance for EV integration [1]. Dealing with Fast Charging, the study determined that 300kW Fast Charging, which corresponds to 10 minutes charging for a 50...... charging, rated at 50 kW, fast charging would be easier in both Denmark and Bornholm scenarios. For each scenario and charging power level, the possible number of EVs is estimated and finally architectural design options are proposed. Technical assessment is performed for evaluating the benefits...

  15. Central serous chorioretinopathy

    DEFF Research Database (Denmark)

    Wang, M.; Munch, I.C.; Hasler, P.W.

    2008-01-01

    Central serous chorioretinopathy (CSC) is a disease of the retina characterize by serous detachment of the neurosensory retina secondary to one or more focal lesions of the retinal pigment epithelium (RPE). CSC occurs most frequently in mid-life and more often in men than in women. Major symptoms...... and hypercortisolism. Ophthalmoscopic signs of CSC range from mono- or paucifocal RPE lesions with prominent elevation of the neurosensory retina by clear fluid - typical of cases of recent onset - to shallow detachments overlying large patches of irregularly depigmented RPE. The spectrum of lesions includes RPE...... detachments. Granular or fibrinous material may accumulate in the subretinal cavity. Serous detachment often resolves spontaneously. From first contact, counselling about the potential relation to stress and glucocorticoid medication is warranted. After 3 months without resolution of acute CSC or in chronic...

  16. Central Accountability System (CLAS)

    International Nuclear Information System (INIS)

    Hairston, L.A.

    1991-01-01

    The Central Accountability System (CLAS) is a high level accountability system that consolidates data from the site's 39 material balance areas (MBA) for reporting to Westinghouse Savannah River Company (WSRC) management, Department of Energy (DOE) and the Nuclear Materials Management and Safeguards System (NMMSS) in Oak Ridge, TN. Development of the system began in 1989 and became operational in April, 1991. The CLAS system enhances data accuracy and accountability records, resulting in increased productivity and time and cost savings. This paper reports that the system is in compliance with DOE Orders and meets NMMSS reporting requirements. WSRC management is provided with the overall status of the site's nuclear material inventory. CLAS gives WSRC a leading edge in accounting technology and enhances good accounting practices

  17. Central America's shrinking forests.

    Science.gov (United States)

    1992-01-01

    This news brief reports that 66% of deforestation in Central America has happened in the past 40 years, based on World Conservation Union (WCU) data. Deforestation is expected to continue. The population of Central America and Mexico grew by 28% between 1977 and 1987. Growth is decreasing but remains high at 2.5% in all countries of the region except Panama. 29 million was the regional population in 1990; the projection is for 63 million by 2025. Population is migrating to urban centers. Forests declined by 13% and croplands increased from 4% to 13% of total land area and pasture land from 2% to 37%. There was an increase in unproductive land from 145 to 24%, i.e., 50% of El Salvador's land had soil degradation as does 30% of Guatemala's. In addition to deforestation and soil degradation, there has been soil erosion leading to sedimentation buildup near dam sites and in rivers, which diminishes hydroelectric power capability. Silting also affects groundwater resources, which impact on a safe drinking water supply. Population growth results in increased demand for fuelwood, urban land, and agricultural land. New techniques practiced widely are needed in order to meet the region's needs or demands. Slowing population growth buys time for adjusting to the necessary changes needed for sustaining the region's population. WCU urges conservation organizations to raise awareness about the role population plays in environmental degradation, and to support efforts to reduce birth rates. Women's status needs to be improved through income-generating projects, for instance, and cooperation is needed between conservation groups and organizations involved with improving maternal and child health.

  18. SECURITY THREATS IN CENTRAL ASIA

    Directory of Open Access Journals (Sweden)

    Çağla Gül Yesevi

    2013-07-01

    Full Text Available This study will analyze main security threats in Central Asia. It is obvious thatsince the end of Cold War, there have been many security threats in Central Asiaas internal weakness of Central Asian states, terrorism, transnational crime,economic insecurity, environmental issues, drug trafficking, ethnic violence,regional instability. This study will propose thatwith increasing interdependence,states need each other to solve these global security problems. In that sense,regional and sub-regional cooperation between Central Asian states and with otherregional actors has been witnessed. It is clear that the withdrawal of NATO fromAfghanistan will destabilize Central Asia. This study will investigate overallsecurity situation in Central Asia and affects andcontributions of regionalorganizations to Eurasian security

  19. Enhancement of Operating Efficiency Of The Central Coal-Preparation Plant of "MMK - UGOL" Ltd. Under Current Conditions

    Science.gov (United States)

    Basarygin, Maksim

    2017-11-01

    In this article the subject of enhancement of operating efficiency of the central coal-preparation plant of OOO "MMK-UGOL" is encompassed. Modern trends in the development of technologies and equipment for coal beneficiation are due to the following requirements: improving competitiveness of coal products, improvement of quality of marketable products, reduction of coal production cost, environmental requirements: polluting emission abatement, prepared coal saving, improvement of the effectiveness of resource conservation; complex mechanization and beneficiation process automation. In the article the contemporary problems of raw coal benefication under current conditions of the increased dilution of withdrawable coals with rock fractions are considered. Comparative analysis of efficiency of application of modern concentrating equipment under the conditions of the CCPP of OOO "MMK-UGOL" is carried out on the basis of research works. Particular attention is paid to dehydration of produced coal concentrate with content of volatile agents of more than 35.0% and content of fine-dispersed particles in flotation concentrate of more than 50.0%. Comparative analysis of the coal concentrate dehydration technologies is conducted.

  20. [MANAGEMENT OF CENTRAL HYPERSOMNIAS].

    Science.gov (United States)

    Dauvilliers, Yves; Lopez, Régis

    2016-06-01

    Central hypersomnias include narcolepsy type 1, type 2 and idiopathic hypersomnia with daytime sleepiness excessive in the foreground of the clinical symptoms. Despite major advances in our understanding of the mechanisms of the narcolepsy type 1 with a low level of hypocretin-1 in cerebrospinal fluid, its current management is only symptomatic. The current management is also only symptomatic for type 2 narcolepsy and idiopathic hypersomnia with an unknown pathophysiology. Treatment options may vary from a single drug targeting several symptoms or several drugs treating a specific symptom. The treatment of daytime sleepiness is based on modafinil in first intention. Other psychostimulants such as methylphenidate, pitolisant and exceptionally dextro-amfetamine may be considered. In narcolepsy type 1, antidepressants such as inhibitors of the reuptake of serotonin and noradrenaline will be considered to improve cataplexy. Sodium oxybate is an effective treatment on sleepiness, cataplexy and bad night sleep in narcolepsy. The management for other symptoms or comorbidities should be considered it necessary such as hallucinations, sleep paralysis, the disturbed nighttime sleep, unpleasant dreams, parasomnias, depressive symptoms, overweight/obesity, cardiovascular disease and obstructive sleep apnea syndrome. Important therapeutic perspectives are to be expected concerning new psychostimulant and anticataplectiques, but mainly on immune-based therapies administered as early as possible after disease onset and on hypocretin replacement therapy for patients with severe symptoms.

  1. Central metabolism of angiotensins

    International Nuclear Information System (INIS)

    Camara, C.G.

    1984-01-01

    High performance liquid chromatography analyses of the radioactivity derived from 125 I-angiotensins and bound to cellular receptors in the brain and peripheral tissue reveal that, first, the specifically bound radioactivity is a heterogeneous mixture of several molecular species. Second, the observed patterns of 125 I-angiotensin degradation are largely the result of the activity of membrane-bound amino peptidases, which are enriched in the crude mitochrondrial tissue fraction; third, in general, peptidase inhibitors decrease the apparent binding of 125 I-angiotensins to brain tissue, and they decrease this binding more than they decrease the degradation of the radioligands; fourth, peptidase inhibitors specific for individual enzymes, but not broad-spectrum peptidase inhibitors, actually decrease the amount of 125 I-angiotensin II bound to brain tissue, suggesting that angiotensin receptors in the brain may be associated with membrane-bound peptidases; fifth, tyrosine and other aromatic and branched-chain aliphatic amino acids, end products of angiotensin degradation by membrane peptidases, are quickly removed from the extracellular compartment by the activity of a high-affinity transport system, identical with the leucine-preferring uptake system, which is enriched in the crude mitochondrial tissue fraction, containing the synaptosomes; and sixth, the distribution of this uptake system in rat and gerbil brain is nearly identical and corresponds with the central distribution of 125 I-angiotensin binding in the gerbil, but neither with the distribution of 125 I-angiotensin II binding in the rat brain

  2. Mexico and Central America.

    Science.gov (United States)

    Bronfman, M

    1998-01-01

    This article reviews the literature on migration and HIV/AIDS in Mexico and Central America, including Belize, Costa Rica, El Salvador, Guatemala, Honduras, Mexico, Nicaragua, and Panama. Most migrants travel to the US through Mexico. US-Mexico trade agreements created opportunities for increased risk of HIV transmission. The research literature focuses on Mexico. Most countries, with the exception of Belize and Costa Rica, are sending countries. Human rights of migrants are violated in transit and at destination. Migration policies determine migration processes. The Mexican-born population in the US is about 3% of US population and 8% of Mexico's population. About 22% arrived during 1992-97, and about 500,000 are naturalized US citizens. An additional 11 million have a Mexican ethnic background. Mexican migrants are usually economically active men who had jobs before leaving and were urban people who settled in California, Texas, Illinois, and Arizona. Most Mexican migrants enter illegally. Many return to Mexico. The main paths of HIV transmission are homosexual, heterosexual, and IV-drug-injecting persons. Latino migrants frequently use prostitutes, adopt new sexual practices including anal penetration among men, greater diversity of sexual partners, and use of injectable drugs.

  3. CENTRAL EUROPE: Role models

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    Hungary is one of the newcomers to the CERN fold, having joined in 1992. The country's contributions are naturally in line with its slender resources and are not as immediately visible as those of the major Western European Member States. However the approach used and its consequent successes provide a good role model for a smaller nation in an international research environment. This was reflected on 24 September at a meeting of the European Committee for Future Accelerators (ECFA) convened in Budapest, continuing an ECFA tradition of holding meetings in national centres to learn more about the physics programmes of different countries. This tradition started with visits to major West European Centres, but last year ECFA held a meeting in Warsaw, its first in a central European country. By far the largest Hungarian population centre, Budapest is also a hub for national research in this sector, with university centres and the KFKI Research Institute for Particle and Nuclear Physics of the National Academy of Sciences. However important research work is also carried out in the eastern city of Debrecen. Hungarians look back to the classic investigations of Eotvos early this century as the starting point of their national tradition in fundamental physics. (In the mid-80s, these experiments briefly came back into vogue when there was a suggestion of an additional 'fifth force' contribution to nuclear masses.)

  4. Central Hypothyroidism in Miniature Schnauzers

    OpenAIRE

    Voorbij, Annemarie M W Y; Leegwater, Peter A J; Buijtels, Jenny J C W M; Daminet, Sylvie; Kooistra, Hans S

    2016-01-01

    Background: Primary hypothyroidism is a common endocrinopathy in dogs. In contrast, central hypothyroidism is rare in this species. Objectives: The objective of this article is to describe the occurrence and clinical presentation of central hypothyroidism in Miniature Schnauzers. Additionally, the possible role of the thyroid-stimulating hormone (TSH)-releasing hormone receptor (TRHR) gene and the TSH beta (TSHB) gene was investigated. Animals: Miniature Schnauzers with proven central...

  5. Central Asian Drug Trafficking Dilemma

    Science.gov (United States)

    2003-12-01

    Afghanistan and Central Asia have made the region a perfect environment for drug trafficking and use. Weakened governments, corrupt officials, lack of...expanding and increasing the role of the KOGG. If governments in Central Asia are serious about wanting stability, corruption is one of the most...concerning expanding and increasing the role of the KOGG. If governments in Central Asia are serious about wanting stability, corruption is one of the most

  6. Centralized vs. De-centralized Multinationals and Taxes

    DEFF Research Database (Denmark)

    Nielsen, Søren Bo; Raimondos-Møller, Pascalis; Schjelderup, Guttorm

    2005-01-01

    The paper examines how country tax differences affect a multinational enterprise's choice to centralize or de-centralize its decision structure. Within a simple model that emphasizes the multiple conflicting roles of transfer prices in MNEs - here, as a strategic pre-commitment device and a tax...

  7. The Regional Centrality of Vietnam’s Central Highlands

    DEFF Research Database (Denmark)

    Salemink, Oscar

    2018-01-01

    strategic value turned it into a battleground among various Vietnamese parties, France, and the United States. It was here that the outcome of the Indochina wars was determined, but at a terrible price for the local population. After the adoption of economic reforms in reunified Vietnam the Central......Vietnam’s Central Highlands—or Tây Nguyên—area is usually described as remote, backward, and primitive, but this region has played a central role in the history of the surrounding states and the wider East and Southeast Asia region. Far from isolated, the Central Highlands engaged in trade...... various rivalrous polities now known as Vietnam, Champa, Cambodia, Laos, and Thailand, the area occupied a strategic position in the wider mainland Southeast Asia region. With the emergence of a unified, neo-Confucianist Vietnamese state the region lost its centrality until the late colonial era, when its...

  8. Central nervous system tumors

    International Nuclear Information System (INIS)

    Gavin, P.R.; Fike, J.R.; Hoopes, P.J.

    1995-01-01

    Central nervous system (CNS) tumors are relatively common in veterinary medicine, with most diagnoses occurring in the canine and feline species. Numerous tumor types from various cells or origins have been identified with the most common tumors being meningiomas and glial cell tumors. Radiation therapy is often used as an aid to control the clinical signs associated with these neoplasms. In general, these tumors have a very low metastatic potential, such that local control offers substantial benefit. Experience in veterinary radiation oncology would indicate that many patients benefit from radiation treatment. Current practice indicates the need for computed tomography or magnetic resonance imaging studies. These highly beneficial studies are used for diagnosis, treatment planning, and to monitor treatment response. Improvements in treatment planning and radiation delivered to the tumor, while sparing the normal tissues, should improve local control and decrease potential radiation related problems to the CNS. When possible, multiple fractions of 3 Gy or less should be used. The tolerance dose to the normal tissue with this fractionation schedule is 50 to 55 Gy. The most common and serious complications of radiation for CNS tumors is delayed radiation myelopathy and necrosis. Medical management of the patient during radiation therapy requires careful attention to anesthetic protocols, and medications to reduce intracranial pressure that is often elevated in these patients. Canine brain tumors have served as an experimental model to test numerous new treatments. Increased availability of advanced imaging modalities has spawned increased detection of these neoplasms. Early detection of these tumors with appropriate aggressive therapy should prove beneficial to many patients

  9. Central African Republic.

    Science.gov (United States)

    1989-11-01

    The Central African Republic contains 242,000 square miles, which rolling terrain almost 2000 feet above sea level. The climate is tropical, and it has a population of 2.8 million people with a 2.5% growth rate. There are more than 80 ethnic groups including Baya 34%, Banda 28%, Sara 10%, Mandja 9%, Mboum 9%, and M'Baka 7%. The religions are traditional African 35%, protestant 25%, Roman Catholic 25%, and Muslim 15%, and the languages are French and Sangho. The infant mortality rate is 143/1000, with expectancy at 49 years and a 40% literacy rate. The work force of 1 million is 70% agricultural, industry 6% and commerce and service 6% and government 3%. The government consists of a president assisted by cabinet ministers and a single party. Natural resources include diamonds, uranium, timber, gold, and oil, and major industries are beverages, textiles, and soap. Agricultural products feature coffee, cotton, peanuts, tobacco, food crops and livestock. Most of the population live in rural areas and most of the 80 ethnic groups have their own language. This is one of the world's least developed countries, with a per capita income of $375/year. The main problems with development are the poor transportation infrastructure, and the weak internal and international marketing systems. The US and various international organizations have aided in agriculture development, health programs, and family planning. US investment is mainly in diamond and gold mining, and although oil drilling has been successful it is not economically feasible at current prices.

  10. Dublin South Central (DSC)

    LENUS (Irish Health Repository)

    O'Gorman, Clodagh S M

    2010-12-01

    Children who appear healthy, even if they have one or more recognized cardiovascular risk factors, do not generally have outcomes of cardiovascular or other vascular disease during childhood. Historically, pediatric medicine has not aggressively screened for or treated cardiovascular risk factors in otherwise healthy children. However, studies such as the P-Day Study (Pathobiological Determinants of Atherosclerosis in Youth), and the Bogalusa Heart Study, indicate that healthy children at remarkably young ages can have evidence of significant atherosclerosis. With the increasing prevalence of pediatric obesity, can we expect more health problems related to the consequences of pediatric dyslipidemia, hypertriglyceridemia, and atherosclerosis in the future? For many years, medications have been available and used in adult populations to treat dyslipidemia. In recent years, reports of short-term safety of some of these medications in children have been published. However, none of these studies have detailed long-term follow-up, and therefore none have described potential late side-effects of early cholesterol-lowering therapy, or potential benefits in terms of reduction of or delay in cardiovascular or other vascular end-points. In 2007, the American Heart Association published a scientific statement on the use of cholesterol-lowering therapy in pediatric patients. In this review paper, we discuss some of the current literature on cholesterol-lowering therapy in children, including the statins that are currently available for use in children, and some of the cautions with using these and other cholesterol-lowering medications. A central tenet of this review is that medications are not a substitute for dietary and lifestyle interventions, and that even in children on cholesterol-lowering medications, physicians should take every opportunity to encourage children and their parents to make healthy diet and lifestyle choices.

  11. Payments and Central Bank Policy

    DEFF Research Database (Denmark)

    Korsgaard, Søren

    outcomes in the money market. The third, "Collateralized Lending and Central Bank Collateral Policy", considers the emergence of credit constraints under collateralized lending, and how central banks use collateral policy to mitigate these constraints. While the chapters can be read independently...

  12. Central Clearing of OTC Derivatives

    DEFF Research Database (Denmark)

    Cont, Rama; Kokholm, Thomas

    2014-01-01

    We study the impact of central clearing of over-the-counter (OTC) transactions on counterparty exposures in a market with OTC transactions across several asset classes with heterogeneous characteristics. The impact of introducing a central counterparty (CCP) on expected interdealer exposure is de...

  13. CT diagnosis of central neurofibromatosis

    International Nuclear Information System (INIS)

    Jordanov, J.; Poptodorov, G.; Nacheva, N.; Shirov, T.

    1997-01-01

    Central neurofibromatosis (NF2) is a condition characterized by multiple tumors involving the central nervous system. The typical intracranial CT findings in five patients presenting NF2, and the natural history of the disease in three illustrative cases are described. The early diagnosis of asymptomatic lesions may prove of utmost importance for the patient

  14. Central presbycusis: an emerging view.

    Science.gov (United States)

    Gates, George A

    2012-07-01

    Age-related dysfunction of the central auditory system (central presbycusis) is common but rarely looked for by those who provide aural rehabilitation. Patients who complain of difficulty hearing in noise--the key symptom of central presbycusis--are generally disadvantaged with conventional rehabilitation. This symptom should be documented with commercially available speech-in-noise tests, which use materials that are uncomplicated to administer. Those patients who perform poorly on such tests should have a customized rehabilitation program aimed at optimizing their remaining communication abilities. Otolaryngologists who provide auditory rehabilitation may wish to consider expanding their practices to meet the communication needs of older patients with central presbycusis. Central presbycusis is an emerging area for basic and clinical research in auditory neurotology, particularly in the relation of cognitive dysfunction to impaired auditory processing.

  15. Central control of body temperature.

    Science.gov (United States)

    Morrison, Shaun F

    2016-01-01

    Central neural circuits orchestrate the behavioral and autonomic repertoire that maintains body temperature during environmental temperature challenges and alters body temperature during the inflammatory response and behavioral states and in response to declining energy homeostasis. This review summarizes the central nervous system circuit mechanisms controlling the principal thermoeffectors for body temperature regulation: cutaneous vasoconstriction regulating heat loss and shivering and brown adipose tissue for thermogenesis. The activation of these thermoeffectors is regulated by parallel but distinct efferent pathways within the central nervous system that share a common peripheral thermal sensory input. The model for the neural circuit mechanism underlying central thermoregulatory control provides a useful platform for further understanding of the functional organization of central thermoregulation, for elucidating the hypothalamic circuitry and neurotransmitters involved in body temperature regulation, and for the discovery of novel therapeutic approaches to modulating body temperature and energy homeostasis.

  16. Centralized digital control of accelerators

    International Nuclear Information System (INIS)

    Melen, R.E.

    1983-09-01

    In contrasting the title of this paper with a second paper to be presented at this conference entitled Distributed Digital Control of Accelerators, a potential reader might be led to believe that this paper will focus on systems whose computing intelligence is centered in one or more computers in a centralized location. Instead, this paper will describe the architectural evolution of SLAC's computer based accelerator control systems with respect to the distribution of their intelligence. However, the use of the word centralized in the title is appropriate because these systems are based on the use of centralized large and computationally powerful processors that are typically supported by networks of smaller distributed processors

  17. Central European gas market perspectives

    International Nuclear Information System (INIS)

    Vanous, Jan

    1999-01-01

    This presentation deals with (1) Definition of the Central European market, (2) Factors driving up consumption of natural gas in Central and Eastern Europe, (3) Role of natural gas in regional energy consumption, (4) Position of natural gas in individual country markets, (5) Future sources of imported natural gas into the region. The Central European market are the eleven countries Albania, Bulgaria, Croatia, Czech Republic, Hungary, Macedonia, Poland, Romania, Serbia and Montenegro, Slovakia, and Slovenia, with a total population of 121 million. This market is comparable to combined France and Italy in terms of population, but only 30% of its size in terms of GDP

  18. Demographic tensions in Central America.

    Science.gov (United States)

    1986-08-01

    This discussion of Central America focuses on the rapid growth of its population, its stagnating economy, and those countries that are socioeconomically advanced. Between 1950-85 the population of Central America tripled, from 9.1 million to 26. 4 million, due to marked mortality declines and the absence of off-setting fertility declines. The distribution of Central Americas's growing populations sets its population growth apart from that of other developing regions. Currently, almost half of all Central Americans live in cities. Although the average growth rate for Central American countries has fallen and is expected to drop further, the decline does not counterbalance the effect of the absolute rise in population numbers. The average annual growth rate of more than 3% annually in the 1960s fell to about 2.6% in recent years, but this decline is due primarily to socioeconomically advanced Costa Rica and Panama. Central America's age structure further complicates the population crisis. About 43% of Central Americans are under the age of 15. When the increasingly larger young population group enters it reproductive years, the potential for future growth (albeit the falling rate of population increase) is unparalleled. UN population projections show the region's population at 40 million by the year 2000. The 1973 oil crisis began a downward spiral for the buoyant post World War II Central American economy. Between 1950-79, real per capita income growth in Central America doubled, with Central American economies growing an average of 5.3% annually. By the early 1980s, overseas markets of the trade-dependent countries of Central America had dried up due to protectionism abroad and slumping basic commodity prices. These and other factors plunged Central America into its current economic malaise of falling real per capita income, rising unemployment, curtailed export led economic growth, and a rising cost of living. In general, economic growth in Central America

  19. The Central Trigger Processor (CTP)

    CERN Multimedia

    Franchini, Matteo

    2016-01-01

    The Central Trigger Processor (CTP) receives trigger information from the calorimeter and muon trigger processors, as well as from other sources of trigger. It makes the Level-1 decision (L1A) based on a trigger menu.

  20. Russia's Place in Central Asia

    National Research Council Canada - National Science Library

    Edwards, Jonathan

    2001-01-01

    .... Current United States policy toward Russia in Central Asia is tailored to isolate and minimize Russian influence due, in great part to a perception that Russian "heavy-handedness" is restricting...

  1. Percutaneously inserted central catheter - infants

    Science.gov (United States)

    PICC - infants; PQC - infants; Pic line - infants; Per-Q cath - infants ... A percutaneously inserted central catheter (PICC) is a long, very thin, soft plastic tube that is put into a small blood vessel. This article addresses PICCs in ...

  2. CENTRAL PLATEAU REMEDIATION OPTIMIZATION STUDY

    Energy Technology Data Exchange (ETDEWEB)

    BERGMAN, T. B.; STEFANSKI, L. D.; SEELEY, P. N.; ZINSLI, L. C.; CUSACK, L. J.

    2012-09-19

    THE CENTRAL PLATEAU REMEDIATION OPTIMIZATION STUDY WAS CONDUCTED TO DEVELOP AN OPTIMAL SEQUENCE OF REMEDIATION ACTIVITIES IMPLEMENTING THE CERCLA DECISION ON THE CENTRAL PLATEAU. THE STUDY DEFINES A SEQUENCE OF ACTIVITIES THAT RESULT IN AN EFFECTIVE USE OF RESOURCES FROM A STRATEGIC PERSPECTIVE WHEN CONSIDERING EQUIPMENT PROCUREMENT AND STAGING, WORKFORCE MOBILIZATION/DEMOBILIZATION, WORKFORCE LEVELING, WORKFORCE SKILL-MIX, AND OTHER REMEDIATION/DISPOSITION PROJECT EXECUTION PARAMETERS.

  3. Modelación matemática de la flotación de la maza superior de los molinos de caña de azúcar // Mathematical model for instant flotation of top shaft in sugar cane mills

    Directory of Open Access Journals (Sweden)

    Mario Javier Cabello‐Ulloa

    2012-01-01

    Full Text Available En el presente trabajo se desarrolla un modelo matemático de la flotación de la maza superior de losmolinos de caña de azúcar durante su funcionamiento, determinado a partir de medicionesexperimentales de dicha magnitud en el tiempo. Se realiza un ajuste adecuado a los valores medidosexperimentalmente y se obtiene una función analítica que permitirá considerar los efectos de la flotaciónen el estudio del funcionamiento y en los métodos de cálculo de los molinos y sus elementos. Se aplica aun molino en el Complejo Agroindustrial 14 de Julio en Cienfuegos. Se modelan cien segundos defuncionamiento obteniéndose una función que expresa la flotación la que al ser derivada permite obtenerla velocidad y aceleración con que varía la flotación instantánea. Los coeficientes y sus bondades sondados matricialmente para todos los ajustes efectuados al construir la función que define la flotacióninstantánea obtenida en este caso.Palabras claves: molino de caña de azúcar, flotación instantánea, modelación, cinemática del molino._________________________________________________________________AbstractA mathematical model for the instant flotation of the top shaft of sugar cane mill is developed andanalytical function for introduce in the study of other sugar cane mills parts is obtained. The model isapplied to July 14th sugar factory in Cienfuegos. One hundred seconds of work is modeled and a functionsfor floating, velocity and acceleration of floating are obtained. The coefficients and their goodness aregiven in matrix for all the fits made for to build the function that defines the instant flotation obtained in thiscase.Key words: sugar cane mill, instant flotation, modeling, mill kinematics.

  4. Network centrality of metro systems.

    Directory of Open Access Journals (Sweden)

    Sybil Derrible

    Full Text Available Whilst being hailed as the remedy to the world's ills, cities will need to adapt in the 21(st century. In particular, the role of public transport is likely to increase significantly, and new methods and technics to better plan transit systems are in dire need. This paper examines one fundamental aspect of transit: network centrality. By applying the notion of betweenness centrality to 28 worldwide metro systems, the main goal of this paper is to study the emergence of global trends in the evolution of centrality with network size and examine several individual systems in more detail. Betweenness was notably found to consistently become more evenly distributed with size (i.e. no "winner takes all" unlike other complex network properties. Two distinct regimes were also observed that are representative of their structure. Moreover, the share of betweenness was found to decrease in a power law with size (with exponent 1 for the average node, but the share of most central nodes decreases much slower than least central nodes (0.87 vs. 2.48. Finally the betweenness of individual stations in several systems were examined, which can be useful to locate stations where passengers can be redistributed to relieve pressure from overcrowded stations. Overall, this study offers significant insights that can help planners in their task to design the systems of tomorrow, and similar undertakings can easily be imagined to other urban infrastructure systems (e.g., electricity grid, water/wastewater system, etc. to develop more sustainable cities.

  5. CENTRAL MECHANISMS OF ACUPUNCTURE ANALGESIA

    Directory of Open Access Journals (Sweden)

    Eman S. Mansour

    2015-12-01

    Full Text Available Background: Acupuncture is an component of traditional Chinese medicine (TCM that has been used for three thousand years to treat diseases and relieve pain. Pain is found to be the most common reason for people to use acupuncture. Due to recent scientific findings, acupuncture treatment has been accepted worldwide. Numerous trials have been conducted especially in analgesia. The mechanisms of acupuncture analgesia has been widely investigated, however, the underlying mechanism still not clear. This article summarizes the central mechanisms of acupuncture analgesia and reviews recent studies on the topic. Method: We have focused on examining the recent literature on acupuncture analgesia. The central mechanisms of acupuncture analgesia and reviews recent studies on the topic. We focused on the studies related to central mechanisms of acupuncture analgesia from these aspects: (neurophysiology, neurochemistry and neuroanatomy. Result: The result revealed that acupuncture act on various parts of the central nervous system, including the spinal cord, brain stem, cerebral ganglia and cerebral cortex to alleviate pain. The central mechanisms underlying the effects of acupuncture include neurohumors and neurotransmitters, which are involved in analgesia. At spinal level, Spinal opioids, glutamate, norepinephrine and serotonin are the key elements acupuncture-induced analgesia. At brain level, Endogenous opioid peptides, limbic system play essential roles in mediating the analgesia. Conclusion: Acupuncture is an effective approach to pain management. There is good evidence in both experimental and clinical research that supports acupuncture efficacy in management of chronic pain through central nervous system. Acupuncture should be strongly used as a part of pain management plans. This work helps in improving our understanding of the scientific basis underlying acupuncture analgesia.

  6. Central Mandibular Nerve Sheath Myxoma

    Directory of Open Access Journals (Sweden)

    Narges Ghazi

    2018-03-01

    Full Text Available Nerve sheath myxoma has been described as a rare neural tumor arising from Schwann cells. It is observed most frequently in the central area of the face, neck and upper extremities. In the past the term neurothekeoma was used as synonym for nerve sheath myxoma but according to new reports, they are separate entities which can be confirmed by immunohistochemistry as in our case. Oral involvement of this tumor is extremely rare. Here, we present an unusual case of nerve sheath myxoma in the mandible of a 22-year old female patient. This case appears to be the first myxomatous variant which is centrally located in the mandible.

  7. Shared breastfeeding in central Africa

    NARCIS (Netherlands)

    Ramharter, Michael; Chai, Sanders K.; Adegnika, Ayola A.; Klöpfer, Anna; Längin, Matthias; Agnandji, Selidji T.; Oyakhirome, Sunny; Schwarz, Norbert G.; Grobusch, Martin P.; Issifou, Saadon; Kremsner, Peter G.

    2004-01-01

    In this study, shared breastfeeding is described asa novel risk factor for vertical HIV transmission. This cross-sectional survey conducted in the central African country Gabon found that 40% of lactating mothers also breastfed other children than their own, and as many children were additionally

  8. Copycats of the Central Himalayas

    NARCIS (Netherlands)

    P.A. Arora (Payal)

    2009-01-01

    textabstractThis case study highlights practices of a rarely documented group of neo-users of the Internet or newbies from Central Himalayas, serving as a catalyst for delving deeply into the act of ‘plagiarism’ in online learning By looking at such ‘learning’ practices away from schools, namely

  9. New Economy, Old Central Banks?

    NARCIS (Netherlands)

    Berk, Jan Marc

    2002-01-01

    Proponents of the so-called New Economy claim that it entails a structural change of the economy. Such a change, in turn, would require the central bank to rethink its monetary policy to the extent that traditional relationships between inf1ation and economic growth are no longer valid. But such a

  10. Central American Tactical Airlift Wing

    Science.gov (United States)

    2017-03-17

    homeland security, and airlift capabilities in particular, will depend on the proper and ingenious provision of needed resources. Central America...down cost includes construction and renovation of hangars, office space, and support buildings. It also includes utility infrastructure such as roads

  11. /S/ in Central American Spanish.

    Science.gov (United States)

    Lipski, John M.

    1985-01-01

    Describes the behavior of the phoneme /s/ in Central American Spanish by comparing the speech patterns of residents of Guatemala City, San Salvador, Tegucigalpa, San Jose, and Managua. Considers the possible diachronic processes which could have given rise to the current configurations and the theoretical consequences implied by the…

  12. Central pontine myelinolysis CASE REPORT

    African Journals Online (AJOL)

    Differential diagnosis of central pontine myelinolysis includes infarct, metastasis, glioma, multiple sclerosis, encephalitis, radiotherapy and chemotherapy.3 However concomitant involvement of the pons and basal ganglia is specific for osmotic myelinolysis.7 In such cases the imaging differential diagnosis includes hypoxia, ...

  13. Central pontine myelinolysis CASE REPORT

    African Journals Online (AJOL)

    Central pontine myelinolysis is a demyelinating disease of the pons characterised by loss of myelin and oligodendroglia with relative neuron sparing. This condition classically occurs in alcoholics, malnourished or chronically debilitated adults1 and usually occurs in the hospital setting, a few days following rapid correction ...

  14. Central African Journal of Medicine

    African Journals Online (AJOL)

    The Central African Journal of Medicine is a quarterly refereed general medical journal which seeks to promote the practice and science of medicine in Africa. Emphasis is placed on general medical topics, reflecting common and important conditions in the region. The journal also covers related medical fields. Submissions ...

  15. Centrality as a Prior Criterion.

    Science.gov (United States)

    Lincoln, Yvonna S.; Tuttle, Jane

    Program discontinuance at colleges and universities is often linked to issues of program demand and quality. However, neither low demand nor low quality is sufficient for program discontinuance without a judgment on the criterion of the centrality of the program to the institution's core mission. Colleges' retrenchment and survival mechanisms…

  16. Quantitative analysis of Nipah virus proteins released as virus-like particles reveals central role for the matrix protein

    Directory of Open Access Journals (Sweden)

    Eaton Bryan T

    2007-01-01

    Full Text Available Abstract Background Nipah virus (NiV is an emerging paramyxovirus distinguished by its ability to cause fatal disease in both animal and human hosts. Together with Hendra virus (HeV, they comprise the genus Henipavirus in the Paramyxoviridae family. NiV and HeV are also restricted to Biosafety Level-4 containment and this has hampered progress towards examining details of their replication and morphogenesis. Here, we have established recombinant expression systems to study NiV particle assembly and budding through the formation of virus-like particles (VLPs. Results When expressed by recombinant Modified Vaccinia virus Ankara (rMVA or plasmid transfection, individual NiV matrix (M, fusion (F and attachment (G proteins were all released into culture supernatants in a membrane-associated state as determined by sucrose density gradient flotation and immunoprecipitation. However, co-expression of F and G along with M revealed a shift in their distribution across the gradient, indicating association with M in VLPs. Protein release was also altered depending on the context of viral proteins being expressed, with F, G and nucleocapsid (N protein reducing M release, and N release dependent on the co-expression of M. Immunoelectron microscopy and density analysis revealed VLPs that were similar to authentic virus. Differences in the budding dynamics of NiV proteins were also noted between rMVA and plasmid based strategies, suggesting that over-expression by poxvirus may not be appropriate for studying the details of recombinant virus particle assembly and release. Conclusion Taken together, the results indicate that NiV M, F, and G each possess some ability to bud from expressing cells, and that co-expression of these viral proteins results in a more organized budding process with M playing a central role. These findings will aid our understanding of paramyxovirus particle assembly in general and could help facilitate the development of a novel vaccine

  17. A Randomized Central Limit Theorem

    International Nuclear Information System (INIS)

    Eliazar, Iddo; Klafter, Joseph

    2010-01-01

    The Central Limit Theorem (CLT), one of the most elemental pillars of Probability Theory and Statistical Physics, asserts that: the universal probability law of large aggregates of independent and identically distributed random summands with zero mean and finite variance, scaled by the square root of the aggregate-size (√(n)), is Gaussian. The scaling scheme of the CLT is deterministic and uniform - scaling all aggregate-summands by the common and deterministic factor √(n). This Letter considers scaling schemes which are stochastic and non-uniform, and presents a 'Randomized Central Limit Theorem' (RCLT): we establish a class of random scaling schemes which yields universal probability laws of large aggregates of independent and identically distributed random summands. The RCLT universal probability laws, in turn, are the one-sided and the symmetric Levy laws.

  18. Educated Cities and Regional Centralization

    DEFF Research Database (Denmark)

    Eriksen, Jesper

    This paper provides an overview of Danish student to population ratios in post-primary education from 1982 to 2013. Using administrative register data I document a nationally increased share of enrolled students to population over the 32 years period. The increase followed a pattern of regional...... centralization where the shares of students rose significantly more in urban municipalities than non-urban municipalities. The highest shares of students as well as fastest increases were seen in the municipalities of the four largest cities, Copenhagen, Århus, Odense, and Aalborg. At the national level...... and vocational education students to population both in 1982 and 2013. The paper is concluded with suggestions for future research linking these patterns of regional centralization to challenges such as technological skill-bias and an increasing importance of continuous learning, as well as inequality and social...

  19. A centralized audio presentation manager

    Energy Technology Data Exchange (ETDEWEB)

    Papp, A.L. III; Blattner, M.M.

    1994-05-16

    The centralized audio presentation manager addresses the problems which occur when multiple programs running simultaneously attempt to use the audio output of a computer system. Time dependence of sound means that certain auditory messages must be scheduled simultaneously, which can lead to perceptual problems due to psychoacoustic phenomena. Furthermore, the combination of speech and nonspeech audio is examined; each presents its own problems of perceptibility in an acoustic environment composed of multiple auditory streams. The centralized audio presentation manager receives abstract parameterized message requests from the currently running programs, and attempts to create and present a sonic representation in the most perceptible manner through the use of a theoretically and empirically designed rule set.

  20. Versatile central spectrometer for ISABELLE

    International Nuclear Information System (INIS)

    Cheng, D.; Goulianso, K.; Knapp, B.; Rosen, J.; Schlein, P.

    1975-01-01

    A large aperture magnetic spectrometer is proposed to study hadrons and leptons produced in the central region at Isabelle. The essential element of the spectrometer is a large double-dipole magnet system with common flux return straddling the intersection region. The air gaps provide magnetic analysis of charged particle for up to 50 percent of the azimuthal angular range. Drift chambers, Cherenkov counters and shower detectors positioned on both sides of the beam lines comprise two spectrometers for analysis of hadrons and electrons. Muons can be momentum analyzed over a large fraction at the azimuthal angle by utilizing the upper and lower sections on the magnet yoke to provide hadron filtering and magnetic deflection. Cylindrical chambers around the vacuum pipe provide multiplicity information for events of interest. The proposed magnet configuration allows unobscured coverage of smaller angle particles with the addition of septum magnet spectrometers downstream of the central magnet in both arms.