WorldWideScience

Sample records for surface thermal activity

  1. Surface dielectric relaxation: probing technique and its application to thermal activation dynamics of polymer surface.

    Science.gov (United States)

    Ishii, Masashi

    2010-09-01

    For dynamic analyses of a polymer surface, a dielectric relaxation measurement technique with parallel electrodes placed away from the surface was developed. In this technique, a liquid heating medium was filled in the space between the polymer surface and the electrodes. The construction that maintains the surface can clarify the physical interactions between the liquid and the bare surface and controlling the temperature of the liquid reveals the thermal activation property of the surface. The dielectric relaxation spectrum of the surface convoluted into the bulk and liquid spectra can be obtained by a reactance analysis and the surface spectrum is expressed with an equivalent resistance-capacitance parallel circuit. On the basis of the electromechanical analogy, the electric elements can be converted into mechanical elements that indicate the viscoelasticity of the polymer surface. Using these measurement and analysis techniques, the electric and mechanical properties of the surface of a gelatinized chloroprene rubber sample were analyzed.

  2. Experimental and Numerical Investigation of Design Parameters for Hydronic Embedded Thermally Active Surfaces

    DEFF Research Database (Denmark)

    Marcos-Meson, Victor; Pomianowski, Michal Zbigniew; E. Poulsen, Søren

    2015-01-01

    This paper evaluates the principal design parameters affecting the thermal performance of embedded hydronic Thermally Active Surfaces (TAS), combining the Response Surface Method (RSM) with the Finite Elements Method (FEM). The study ranks the combined effects of the parameters on the heat flux...

  3. Surface thermal oxidation on titanium implants to enhance osteogenic activity and in vivo osseointegration

    Science.gov (United States)

    Wang, Guifang; Li, Jinhua; Lv, Kaige; Zhang, Wenjie; Ding, Xun; Yang, Guangzheng; Liu, Xuanyong; Jiang, Xinquan

    2016-08-01

    Thermal oxidation, which serves as a low-cost, effective and relatively simple/facile method, was used to modify a micro-structured titanium surface in ambient atmosphere at 450 °C for different time periods to improve in vitro and in vivo bioactivity. The surface morphology, crystallinity of the surface layers, chemical composition and chemical states were evaluated by field-emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Cell behaviours including cell adhesion, attachment, proliferation, and osteogenic differentiation were observed in vitro study. The ability of the titanium surface to promote osseointegration was evaluated in an in vivo animal model. Surface thermal oxidation on titanium implants maintained the microstructure and, thus, both slightly changed the nanoscale structure of titanium and enhanced the crystallinity of the titanium surface layer. Cells cultured on the three oxidized titanium surfaces grew well and exhibited better osteogenic activity than did the control samples. The in vivo bone-implant contact also showed enhanced osseointegration after several hours of oxidization. This heat-treated titanium enhanced the osteogenic differentiation activity of rBMMSCs and improved osseointegration in vivo, suggesting that surface thermal oxidation could potentially be used in clinical applications to improve bone-implant integration.

  4. Textural, surface, thermal and sorption properties of the functionalized activated carbons and carbon nanotubes

    Directory of Open Access Journals (Sweden)

    Nowicki Piotr

    2015-12-01

    Full Text Available Two series of functionalised carbonaceous adsorbents were prepared by means of oxidation and nitrogenation of commercially available activated carbon and multi-walled carbon nanotubes. The effect of nitrogen and oxygen incorporation on the textural, surface, thermal and sorption properties of the adsorbents prepared was tested. The materials were characterized by elemental analysis, low-temperature nitrogen sorption, thermogravimetric study and determination of the surface oxygen groups content. Sorptive properties of the materials obtained were characterized by the adsorption of methylene and alkali blue 6B as well as copper(II ions. The final products were nitrogen- and oxygen-enriched mesoporous adsorbents of medium-developed surface area, showing highly diverse N and O-heteroatom contents and acidic-basic character of the surface. The results obtained in our study have proved that through a suitable choice of the modification procedure of commercial adsorbents it is possible to produce materials with high sorption capacity towards organic dyes as well as copper(II ions.

  5. Surface valence transformation during thermal activation and hydrogenation thermodynamics of Mg-Ni-Y melt-spun ribbons

    Science.gov (United States)

    Zhang, Tiebang; Song, Wenjie; Kou, Hongchao; Li, Jinshan

    2016-05-01

    In this work, phase compositions and chemical valence states on the surface and subsurface of Mg67Ni33-xYx (x = 0, 1, 3, 6) ribbons during thermal activation have been investigated by X-ray photoelectron spectroscopy (XPS). The results indicate that the surface contaminants of melt-spun ribbons are mainly MgO, NiO, Y2O3 and organics. The oxides/hydroxides of Mg67Ni33-xYx (x = 0, 1, 3, 6) melt-spun ribbons are removed from the surface during thermal activation. Surface chemical valence firstly transforms from oxidized state to the metallic one during thermal activation, which accounts for hydrogenation of Mg67Ni33-xYx melt-spun ribbons. Hydrogen absorption capacities of Mg67Ni33-xYx (x = 0, 1, 3, 6) melt-spun ribbons are enhanced with the increase of cycle numbers during thermal activation. Hydrogenation thermodynamics of activated Mg67Ni33-xYx (x = 0, 1, 3, 6) melt-spun ribbons have been also compared and correlated with the surface valence transformation. The obtained enthalpy of hydride formation is -55.5, -50.5, -46.9 and -48.6 kJ/mol for Mg67Ni33-xYx melt-spun ribbons with x = 0, 1, 3 and 6, respectively.

  6. Thermal activity on Enceladus

    Science.gov (United States)

    Tobie, G.; Besserer, J.; Behounkova, M.; Cadek, O.; Choblet, G.; Sotin, C.

    2009-04-01

    Observations by Cassini have revealed that Enceladus' souh pole is highly active, with jets of icy particles and water vapour emanated from narrow tectonic ridges, called "tiger stripes". This jet activity is associated to a very high thermal emission mainly focused along the tectonic ridges. Heat power required to sustain such an activity is probably related to the dissipation of mechanical energy due to tidal forces exerted by Saturn. However, the dissipation process and its relation to the tectonic features are not clearly established. Both shear heating along the tectonic ridges and viscous dissipation in the convective part of the ice shell could contribute to the energy budget (Nimmo et al. 2007, Tobie et al. 2008). Tobie et al. (2008) pointed out that only interior models with a liquid water layer at depth, covering at least ~2/3 of the southern hemisphere, can explain the observed magnitude of dissipation and its particular location at the south pole. However, the long term stability of such a liquid reservoir remains problematic (Roberts and Nimmo 2007) and the possible link between the liquid reservoir and the surface activities is unknown. Concentration of tidal stresses along the tiger ridges have also been invoked as a mechanism to trigger the eruptive processes (Hurtford et al. 2007, Smith-Konter et al. 2008). However, those models do not take into account a realistic rheological structure for the ice shell when computing the fluctuating stress field. Moreover, the effect of the faults on the background tidal stress is neglected. In particular, low viscosity values are expected to be associated with the shear zone along the tiger stripes and may have a significant impact of the global tidal stress field. In order to self-consistently determine the tidal deformation and its impact on the thermal activity on Enceladus, we are currently developing a 3D model that combines a thermal convection code in spherical geometry (Choblet et al. 2007) and a

  7. Improving spatio-temporal resolution of infrared images to detect thermal activity of defect at the surface of inorganic glass

    Science.gov (United States)

    Corvec, Guillaume; Robin, Eric; Le Cam, Jean-Benoît; Sangleboeuf, Jean-Christophe; Lucas, Pierre

    2016-07-01

    This paper proposes a noise suppression methodology to improve the spatio-temporal resolution of infrared images. The methodology is divided in two steps. The first one consists in removing the noise from the temporal signal at each pixel. Three basic temporal filters are considered for this purpose: average filter, cost function minimization (FIT) and short time Fast Fourier Transform approach (STFFT). But while this step effectively reduces the temporal signal noise at each pixel, the infrared images may still appear noisy. This is due to a random distribution of a residual offset value of pixels signal. Hence in the second step, the residual offset is identified by considering thermal images for which no mechanical loading is applied. In this case, the temperature variation field is homogeneous and the value of temperature variation at each pixel is theoretically equal to zero. The method is first tested on synthetic images built from infrared computer-generated images combined with experimental noise. The results demonstrate that this approach permits to keep the spatial resolution of infrared images equal to 1 pixel. The methodology is then applied to characterize thermal activity of a defect at the surface of inorganic glass submitted to cyclic mechanical loading. The three basic temporal filters are quantitatively compared and contrasted. Results obtained demonstrate that, contrarily to a basic spatio-temporal approach, the denoising method proposed is suitable to characterize low thermal activity combined to strong spatial gradients induced by cyclic heterogeneous deformations.

  8. Vesta surface thermal properties map

    Science.gov (United States)

    Capria, Maria Teresa; Tosi, F.; De Santis, Maria Cristina; Capaccioni, F.; Ammannito, E.; Frigeri, A.; Zambon, F; Fonte, S.; Palomba, E.; Turrini, D.; Titus, T.N.; Schroder, S.E.; Toplis, M.J.; Liu, J.Y.; Combe, J.-P.; Raymond, C.A.; Russell, C.T.

    2014-01-01

    The first ever regional thermal properties map of Vesta has been derived from the temperatures retrieved by infrared data by the mission Dawn. The low average value of thermal inertia, 30 ± 10 J m−2 s−0.5 K−1, indicates a surface covered by a fine regolith. A range of thermal inertia values suggesting terrains with different physical properties has been determined. The lower thermal inertia of the regions north of the equator suggests that they are covered by an older, more processed surface. A few specific areas have higher than average thermal inertia values, indicative of a more compact material. The highest thermal inertia value has been determined on the Marcia crater, known for its pitted terrain and the presence of hydroxyl in the ejecta. Our results suggest that this type of terrain can be the result of soil compaction following the degassing of a local subsurface reservoir of volatiles.

  9. Surface chemistry of Au/TiO2: Thermally and photolytically activated reactions

    Science.gov (United States)

    Panayotov, Dimitar A.; Morris, John R.

    2016-03-01

    The fascinating particle size dependence to the physical, photophysical, and chemical properties of gold has motivated thousands of studies focused on exploring the ability of supported gold nanoparticles to catalyze chemical transformations. In particular, titanium dioxide-supported gold (Au/TiO2) nanoparticles may provide the right combination of electronic structure, structural dynamics, and stability to affect catalysis in important practical applications from environmental remediation to selective hydrogenation to carbon monoxide oxidation. Harnessing the full potential of Au/TiO2 will require a detailed atomic-scale understanding of the thermal and photolytic processes that accompany chemical conversion. This review describes some of the unique properties exhibited by particulate gold before delving into how those properties affect chemistry on titania supports. Particular attention is given first to thermally driven reactions on single crystal system. This review then addresses nanoparticulate samples in an effort begin to bridge the so-called materials gap. Building on the foundation provided by the large body of work in the field of thermal catalysis, the review describes new research into light-driven catalysis on Au/TiO2. Importantly, the reader should bear in mind throughout this review that thermal chemistry and thermal effects typically accompany photochemistry. Distinguishing between thermally-driven stages of a reaction and photo-induced steps remains a significant challenge, but one that experimentalists and theorists are beginning to decipher with new approaches. Finally, a summary of several state-of-the-art studies describes how they are illuminating new frontiers in the quest to exploit Au/TiO2 as an efficient catalyst and low-energy photocatalyst.

  10. Thermal modification of activated carbon surface chemistry improves its capacity as redox mediator for azo dye reduction

    OpenAIRE

    Pereira, Luciana; Pereira, Ricardo; Pereira, M. F. R.; Van der Zee, F. P.; Cervantes, F. J.; Alves, M.M.

    2010-01-01

    The surface chemistry of a commercial AC (AC0) was selectively modified, without changing significantly its textural properties, by chemical oxidation with HNO3 (ACHNO3 ) and O2 (ACO2 ), and thermal treatments under H2 (ACH2) or N2 (ACN2 ) flow. The effect of modified AC on anaerobic chemical dye reduction was assayed with sulphide at different pH values 5, 7 and 9. Four dyes were tested: Acid Orange 7, Reactive Red 2, Mordant Yellow 10 and Direct Blue 71. Batch experiments with l...

  11. Thermal Activated Envelope

    DEFF Research Database (Denmark)

    Foged, Isak Worre; Pasold, Anke

    2015-01-01

    search procedure, the combination of materials and their bonding temperature is found in relation to the envelope effect on a thermal environment inside a defined space. This allows the designer to articulate dynamic composites with time-based thermal functionality, related to the material dynamics......, environmental dynamics and occupancy dynamics. Lastly, a physical prototype is created, which illustrates the physical expression of the bi-materials and the problems related to manufacturing of these composite structures....

  12. Incorporation of low energy activated nitrogen onto HOPG surface: Chemical states and thermal stability studies by in-situ XPS and Raman spectroscopy

    Science.gov (United States)

    Chandran, Maneesh; Shasha, Michal; Michaelson, Shaul; Hoffman, Alon

    2016-09-01

    In this paper we report the chemical states analysis of activated nitrogen incorporated highly oriented pyrolytic graphite (HOPG) surface under well-controlled conditions. Nitrogen incorporation is carried out by two different processes: an indirect RF nitrogen plasma and low energy (1 keV) N2+ implantation. Bonding configuration, concentration and thermal stability of the incorporated nitrogen species by aforesaid processes are systematically compared by in-situ X-ray photoelectron spectroscopy (XPS). Relatively large concentration of nitrogen is incorporated onto RF nitride HOPG surface (16.2 at.%), compared to N2+ implanted HOPG surface (7.7 at.%). The evolution of N 1s components (N1, N2, N3) with annealing temperature is comprehensively discussed, which indicates that the formation and reorganization of local chemical bonding states are determined by the process of nitridation and not by the prior chemical conditioning (i.e., amorphization or hydrogenation) of the HOPG surface. A combined XPS and Raman spectroscopy studies revealed that N2+ implantation process resulted in a high level of defects to the HOPG surface, which cannot be annealed-out by heat treatment up to 1000 °C. On the other hand, the RF nitrogen plasma process did not produce a high level of surface defects, while incorporating nearly the same amount of stable nitrogen species.

  13. Thermal smoothing of rough surfaces in vacuo

    Science.gov (United States)

    Wahl, G.

    1986-01-01

    The derivation of equations governing the smoothing of rough surfaces, based on Mullins' (1957, 1960, and 1963) theories of thermal grooving and of capillarity-governed solid surface morphology is presented. As an example, the smoothing of a one-dimensional sine-shaped surface is discussed.

  14. Multipole surface solitons in layered thermal media

    CERN Document Server

    Kartashov, Yaroslav V; Torner, Lluis

    2008-01-01

    We address the existence and properties of multipole solitons localized at a thermally insulating interface between uniform or layered thermal media and a linear dielectric. We find that in the case of uniform media, only surface multipoles with less than three poles can be stable. In contrast, we reveal that periodic alternation of the thermo-optic coefficient in layered thermal media makes possible the stabilization of higher order multipoles.

  15. On orbit surfacing of thermal control surfaces

    Science.gov (United States)

    Racette, G. W.

    1984-01-01

    Substrates to be contaminated and contamination source were prepared. Additional information on paint spray method apparatus was obtained. Silver teflon second surface mirror samples and S 13 GLO paint samples were mounted, photographed under the microscope and measured to establish baseline data. Atomic oxygen cleaning and spray painting are being considered. Electrostatic powder and plasma spray coating systems appear to have serious drawbacks.

  16. Thermally activated technologies: Technology Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2003-05-01

    The purpose of this Technology Roadmap is to outline a set of actions for government and industry to develop thermally activated technologies for converting America’s wasted heat resources into a reservoir of pollution-free energy for electric power, heating, cooling, refrigeration, and humidity control. Fuel flexibility is important. The actions also cover thermally activated technologies that use fossil fuels, biomass, and ultimately hydrogen, along with waste heat.

  17. Thermally activated technologies: Technology Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2003-05-01

    The purpose of this Technology Roadmap is to outline a set of actions for government and industry to develop thermally activated technologies for converting America’s wasted heat resources into a reservoir of pollution-free energy for electric power, heating, cooling, refrigeration, and humidity control. Fuel flexibility is important. The actions also cover thermally activated technologies that use fossil fuels, biomass, and ultimately hydrogen, along with waste heat.

  18. Silicide induced surface defects in FePt nanoparticle fcc-to-fct thermally activated phase transition

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Shu; Lee, Stephen L. [School of Physics and Astronomy, SUPA, University of St Andrews, St Andrews KY16 9SS (United Kingdom); André, Pascal, E-mail: pjpandre@riken.jp [School of Physics and Astronomy, SUPA, University of St Andrews, St Andrews KY16 9SS (United Kingdom); RIKEN, Wako 351-0198 (Japan); Department of Physics, CNRS-Ewha International Research Center (CERC), Ewha W. University, Seoul 120-750 (Korea, Republic of)

    2016-11-01

    Magnetic nanoparticles (MnPs) are relevant to a wide range of applications including high density information storage and magnetic resonance imaging to name but a few. Among the materials available to prepare MnPs, FePt is attracting growing attention. However, to harvest the strongest magnetic properties of FePt MnPs, a thermal annealing is often required to convert face-centered cubic as synthesized nPs into its tetragonal phase. Rarely addressed are the potential side effects of such treatments on the magnetic properties. In this study, we focus on the impact of silica shells often used in strategies aiming at overcoming MnP coalescence during the thermal annealing. While we show that this shell does prevent sintering, and that fcc-to-fct conversion does occur, we also reveal the formation of silicide, which can prevent the stronger magnetic properties of fct-FePt MnPs from being fully realised. This report therefore sheds lights on poorly investigated and understood interfacial phenomena occurring during the thermal annealing of MnPs and, by doing so, also highlights the benefits of developing new strategies to avoid silicide formation.

  19. D Surface Generation from Aerial Thermal Imagery

    Science.gov (United States)

    Khodaei, B.; Samadzadegan, F.; Dadras Javan, F.; Hasani, H.

    2015-12-01

    Aerial thermal imagery has been recently applied to quantitative analysis of several scenes. For the mapping purpose based on aerial thermal imagery, high accuracy photogrammetric process is necessary. However, due to low geometric resolution and low contrast of thermal imaging sensors, there are some challenges in precise 3D measurement of objects. In this paper the potential of thermal video in 3D surface generation is evaluated. In the pre-processing step, thermal camera is geometrically calibrated using a calibration grid based on emissivity differences between the background and the targets. Then, Digital Surface Model (DSM) generation from thermal video imagery is performed in four steps. Initially, frames are extracted from video, then tie points are generated by Scale-Invariant Feature Transform (SIFT) algorithm. Bundle adjustment is then applied and the camera position and orientation parameters are determined. Finally, multi-resolution dense image matching algorithm is used to create 3D point cloud of the scene. Potential of the proposed method is evaluated based on thermal imaging cover an industrial area. The thermal camera has 640×480 Uncooled Focal Plane Array (UFPA) sensor, equipped with a 25 mm lens which mounted in the Unmanned Aerial Vehicle (UAV). The obtained results show the comparable accuracy of 3D model generated based on thermal images with respect to DSM generated from visible images, however thermal based DSM is somehow smoother with lower level of texture. Comparing the generated DSM with the 9 measured GCPs in the area shows the Root Mean Square Error (RMSE) value is smaller than 5 decimetres in both X and Y directions and 1.6 meters for the Z direction.

  20. Thermal Tomography of Asteroid Surface Structure

    Science.gov (United States)

    Harris, Alan W.; Drube, Line

    2016-12-01

    Knowledge of the surface thermal inertia of an asteroid can provide insight into its surface structure: porous material has a lower thermal inertia than rock. We develop a means to estimate thermal inertia values of asteroids and use it to show that thermal inertia appears to increase with spin period in the case of main-belt asteroids (MBAs). Similar behavior is found on the basis of thermophysical modeling for near-Earth objects (NEOs). We interpret our results in terms of rapidly increasing material density and thermal conductivity with depth, and provide evidence that thermal inertia increases by factors of 10 (MBAs) to 20 (NEOs) within a depth of just 10 cm. Our results are consistent with a very general picture of rapidly changing material properties in the topmost regolith layers of asteroids and have important implications for calculations of the Yarkovsky effect, including its perturbation of the orbits of potentially hazardous objects and those of asteroid family members after the break-up event. Evidence of a rapid increase of thermal inertia with depth is also an important result for studies of the ejecta-enhanced momentum transfer of impacting vehicles (“kinetic impactors”) in planetary defense.

  1. Thermal Tomography of Asteroid Surface Structure

    CERN Document Server

    Harris, Alan

    2016-01-01

    Knowledge of the surface thermal inertia of an asteroid can provide insight into surface structure: porous material has a lower thermal inertia than rock. We develop a means to estimate thermal inertia values of asteroids and use it to show that thermal inertia appears to increase with spin period in the case of main-belt asteroids (MBAs). Similar behavior is found on the basis of thermophysical modeling for near-Earth objects (NEOs). We interpret our results in terms of rapidly increasing material density and thermal conductivity with depth, and provide evidence that thermal inertia increases by factors of 10 (MBAs) to 20 (NEOs) within a depth of just 10 cm. Our results are consistent with a very general picture of rapidly changing material properties in the topmost regolith layers of asteroids and have important implications for calculations of the Yarkovsky effect, including its perturbation of the orbits of potentially hazardous objects and those of asteroid family members after the break-up event. Eviden...

  2. Metallic superhydrophobic surfaces via thermal sensitization

    Science.gov (United States)

    Vahabi, Hamed; Wang, Wei; Popat, Ketul C.; Kwon, Gibum; Holland, Troy B.; Kota, Arun K.

    2017-06-01

    Superhydrophobic surfaces (i.e., surfaces extremely repellent to water) allow water droplets to bead up and easily roll off from the surface. While a few methods have been developed to fabricate metallic superhydrophobic surfaces, these methods typically involve expensive equipment, environmental hazards, or multi-step processes. In this work, we developed a universal, scalable, solvent-free, one-step methodology based on thermal sensitization to create appropriate surface texture and fabricate metallic superhydrophobic surfaces. To demonstrate the feasibility of our methodology and elucidate the underlying mechanism, we fabricated superhydrophobic surfaces using ferritic (430) and austenitic (316) stainless steels (representative alloys) with roll off angles as low as 4° and 7°, respectively. We envision that our approach will enable the fabrication of superhydrophobic metal alloys for a wide range of civilian and military applications.

  3. Thermal radiation from magnetic neutron star surfaces

    CERN Document Server

    Pérez-Azorin, J F; Pons, J A

    2005-01-01

    We investigate the thermal emission from magnetic neutron star surfaces in which the cohesive effects of the magnetic field have produced the condensation of the atmosphere and the external layers. This may happen for sufficiently cool atmospheres with moderately intense magnetic fields. The thermal emission from an isothermal bare surface of a neutron star shows no remarkable spectral features, but it is significantly depressed at energies below some threshold energy. However, since the thermal conductivity is very different in the normal and parallel directions to the magnetic field lines, the presence of the magnetic field is expected to produce a highly anisotropic temperature distribution, depending on the magnetic field geometry. In this case, the observed flux of such an object looks very similar to a BB spectrum, but depressed in a nearly constant factor at all energies. This results in a systematic underestimation of the area of the emitter (and therefore its size) by a factor 5-10 (2-3).

  4. Characteristic analysis on different thermal active surfaces in canopy gap of tropical secondary forest.%热带次生林林窗不同热力作用面特征分析

    Institute of Scientific and Technical Information of China (English)

    张一平; 王进欣; 马友鑫; 刘玉洪

    2001-01-01

    Microclimatic measurements were conducted in the canopy gap of tropical secondary forest in Xishuangbanna in fog cool and dry-hot season. The daytime thermal effect of different thermal active surface in the canopy gap was dis cussed, and the variations of trunk surface temperature near gap edge and of surface temperature on the gap were ana lyzed. The result shows that the woody-wall surface is new thermal active surface on the vicinage of canopy gap, with the exception of the forest canopy surface, soil surface in the forest gap, and soil surface of the interior. Because of the influence of season, situs and time, the thermal effect of different thermal active surface of gap was sigrnificant different. Being subject to fog, the soil surface on the center of canopy gap is an important thermal active surface in the morning; wbhile in the midday and afternoon, because of the influence of incident radiation, the woody wall and soil surface of edge on the east and the woody wall surface of edge on the north are the key thermal active surface of the canopy gap. In the midday, the thermal active was salient on the surface of gap, and in the afternoon, it was salient on the woody wall. The thermal variations of canopy gap of forest are controlled by the thermal characteristics of different thermal active surfaces and by their interaction, affecting the growth of plants.%利用热带次生林林窗边缘树表温和林窗区域地表温的观测资料,探讨了昼间林窗各热力作用面的热 力效应及其变化规律.通过分析林窗边缘树表温和林窗地表温的变化,指出在林窗区域林窗边缘墙面是林冠 面、林窗地面、林内地面之外的新的第4热力作用面;各个热力作用面的热力效应随季节、位置和时刻的不同有 着明显差异.在受浓雾影响的上午,林窗地面热力作用较强;在中午和下午林窗东侧林缘壁面、林窗东侧-东北侧 地面的热力作用显著,中午以林

  5. THERMAL ACTIVATION OF IMMOBILIZED PAPAIN

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    Papain (Papainase, EC 3.4.22.2) was immobilized on porous silica beads by cross linking with glutaraldehyde. The thermal activation of this immobilized papain in aqueous system was found at a temperature range from 50 to 90℃. The higher the temperature, the more active the immobilized papain will possess. At the same time,the durability of the immobilized papain on heating was greatly improved. The effect of additives and salts on the activity of the immobilized papain were also studied. The results showed that the additives and some of the salts studied could markedly enhance the activity of the immobilized papain at elevated temperature.

  6. Building unique surface structure on aramid fibers through a green layer-by-layer self-assembly technique to develop new high performance fibers with greatly improved surface activity, thermal resistance, mechanical properties and UV resistance

    Science.gov (United States)

    Zhou, Lifang; Yuan, Li; Guan, Qingbao; Gu, Aijuan; Liang, Guozheng

    2017-07-01

    Combining green preparation and high performance is becoming the direction of sustainable development of materials. How to simultaneously overcome the two bottlenecks (poor surface activity and UV resistance) of aramid fibers (AFs) while improving thermal and mechanical properties through a green process is still an interesting issue with big challenge. Herein, new AFs (BL-AFs) were prepared by alternately self-assembling SiO2 and MgAlFe layered double hydroxide (LDH) on surfaces of AFs, successively, through a green layer-by-layer (LBL) self-assembly technique without using high temperature and organic solvent. The structures and properties of BL-AFs were systematically studied, which are controllable by adjusting the number of self-assembly cycle. The new fibers with three or more self-assembly cycles have remarkably improved surface activity, thermal resistance, mechanical properties and UV resistance compared with AFs. Typically, with three self-assembly cycles, the initial degradation temperature and char yield of the new fiber (3BL-AF) are as high as 552.9 °C and 81.2%, about 92 °C and 25.2% higher than those of AF, respectively; after 168 h-UV irradiation, the retention of tensile performances of 3BL-AF fiber is as high as 91-95%, about 29-14% higher than that of AF, showing the best overall performances among all modified AFs prepared using a green technique reported so far. The origin behind the attractive performances of BL-AFs is revealed through correlating with structures of original and modified fibers. The excellent comprehensive properties of BL-AFs demonstrate that the green method provided in this study is facile and effective to completely solve the bottlenecks of aramid fibers, and developing higher performance organic fibers.

  7. A new multicomponent salt of imidazole and tetrabromoterepthalic acid: Structural, optical, thermal, electrical transport properties and antibacterial activity along with Hirshfeld surface analysis

    Science.gov (United States)

    Dey, Sanjoy Kumar; Saha, Rajat; Singha, Soumen; Biswas, Susobhan; Layek, Animesh; Middya, Somnath; Ray, Partha Pratim; Bandhyopadhyay, Debasis; Kumar, Sanjay

    2015-06-01

    Herein, we report the structural, optical, thermal and electrical transport properties of a new multicomponent salt (TBTA2-)·2(IM+)·(water) [TBTA-IM] of tetrabromoterepthalic acid (TBTA) with imidazole (IM). The crystal structure of TBTA-IM is determined by both the single crystal and powder X-ray diffraction techniques. The structural analysis has revealed that the supramolecular charge assisted O-⋯Hsbnd N+ hydrogen bonding and Br⋯π interactions play the most vital role in formation of this multicomponent supramolecular assembly. The Hirshfeld surface analysis has been carried out to investigate supramolecular interactions and associated 2D fingerprint plots reveal the relative contribution of these interactions in the crystal structure quantitatively. According to theoretical analysis the HOMO-LUMO energy gap of the salt is 2.92 eV. The salt has been characterized by IR, UV-vis and photoluminescence spectroscopic studies. It shows direct optical transition with band gaps of 4.1 eV, which indicates that the salt is insulating in nature. The photoluminescence spectrum of the salt is significantly different from that of TBTA. Further, a comparative study on the antibacterial activity of the salt with respect to imidazole, Gatifloxacin and Ciprofloxacin has been performed. Moreover, the current-voltage (I-V) characteristic of ITO/TBTA-IM/Al sandwich structure exhibits good rectifying property and the electron tunneling process governs the electrical transport mechanism of the device.

  8. Microbial Characterization of Internal Active Thermal Control System (IATCS) Hardware Surfaces after Five Years of Operation in the International Space Station

    Science.gov (United States)

    Roman, Monsi C.; Weir, Natalee E.; Wilson, Mark E.; Pyle, Barry H.

    2006-01-01

    A flex hose assembly containing aqueous coolant from the International Space Station (ISS) Internal Active Thermal Control System (IATCS) consisting of a 2 foot section of Teflon hose and quick disconnects (QDs) and a Special Performance Checkout Unit (SPCU) heat exchanger containing separate channels of IATCS coolant and iodinated water used to cool spacesuits and Extravehicular Mobility Units (EMUS) were returned for destructive analyses on Shuttle return to flight mission STS-114. The original aqueous IATCS coolant used in Node 1, the Laboratory Module, and the Airlock consisted of water, borate (pH buffer), phosphate (corrosion control), and silver sulfate (microbiological control) at a pH of 9.5 +/- 0.5. Chemical changes occurred after on-orbit implementation including a decrease to pH 8.4 due to the diffusion of carbon dioxide through the Teflon hoses, an increase in nickel ions due to general corrosion of heat exchanger braze coatings, a decrease in phosphate concentration due to precipitation of nickel phosphate, and the rapid disappearance of silver ions due to deposition on hardware surfaces. Also associated with the coolant chemistry changes was an increase in planktonic microorganisms from less than 100 colony forming units (CFU) per 100 ml to approximately 1 million CFU per 100 ml. Attachment and growth of microorganisms to the system surfaces (biofilm) was suspected due to the levels of planktonic microorganisms in the coolant. Biofilms can reduce coolant flow, reduce heat transfer, amplify degradation of system materials initiated by chemical corrosion, and enhance mineral scale formation.

  9. Thermal characterization of nanoporous 'black silicon' surfaces

    Science.gov (United States)

    Nichols, Logan; Duan, Wenqi; Toor, Fatima

    2016-09-01

    In this work we characterize the thermal conductivity properties of nanoprous `black silicon' (bSi). We fabricate the nanoporous bSi using the metal assisted chemical etching (MACE) process utilizing silver (Ag) metal as the etch catalyst. The MACE process steps include (i) electroless deposition of Ag nanoparticles on the Si surface using silver nitrate (AgNO3) and hydrofluoric acid (HF), and (ii) a wet etch in a solution of HF and hydrogen peroxide (H2O2). The resulting porosity of bSi is dependent on the ratio of the concentration of HF to (HF + H2O2); the ratio is denoted as rho (ρ). We find that as etch time of bSi increases the thermal conductivity of Si increases as well. We also analyze the absorption of the bSi samples by measuring the transmission and reflection using IR spectroscopy. This study enables improved understanding of nanoporous bSi surfaces and how they affect the solar cell performance due to the porous structures' thermal properties.

  10. Thermal Cameras in School Laboratory Activities

    Science.gov (United States)

    Haglund, Jesper; Jeppsson, Fredrik; Hedberg, David; Schönborn, Konrad J.

    2015-01-01

    Thermal cameras offer real-time visual access to otherwise invisible thermal phenomena, which are conceptually demanding for learners during traditional teaching. We present three studies of students' conduction of laboratory activities that employ thermal cameras to teach challenging thermal concepts in grades 4, 7 and 10-12. Visualization of…

  11. Bioadhesion to model thermally responsive surfaces

    Science.gov (United States)

    Andrzejewski, Brett Paul

    This dissertation focuses on the characterization of two surfaces: mixed self-assembled monolayers (SAMs) of hexa(ethylene glycol) and alkyl thiolates (mixed SAM) and poly(N-isopropylacrylamide) (PNIPAAm). The synthesis of hexa(ethylene gylcol) alkyl thiol (C11EG 6OH) is presented along with the mass spectrometry and nuclear magnetic resonance results. The gold substrates were imaged prior to SAM formation with atomic force micrscopy (AFM). Average surface roughness of the gold substrate was 0.44 nm, 0.67 nm, 1.65 nm for 15, 25 and 60 nm gold thickness, respectively. The height of the mixed SAM was measured by ellipsometry and varied from 13 to 28°A depending on surface mole fraction of C11EG6OH. The surface mole fraction of C11EG6OH for the mixed SAM was determined by X-ray photoelectron spectroscopy (XPS) with optimal thermal responsive behavior in the range of 0.4 to 0.6. The mixed SAM surface was confirmed to be thermally responsive by contact angle goniometry, 35° at 28°C and ˜55° at 40°C. In addition, the mixed SAM surfaces were confirmed to be thermally responsive for various aqueous mediums by tensiometry. Factors such as oxygen, age, and surface mole fraction and how they affect the thermal responsive of the mixed SAM are discussed. Lastly, rat fibroblasts were grown on the mixed SAM and imaged by phase contrast microscopy to show inhibition of attachment at temperatures below the molecular transition. Qualitative and quantitative measurements of the fibroblast adhesion data are provided that support the hypothesis of the mixed SAM exhibits a dominantly non-fouling molecular conformation at 25°C whereas it exhibits a dominantly fouling molecular conformation at 40°C. The adhesion of six model proteins: bovine serum albumin, collagen, pyruvate kinase, cholera toxin subunit B, ribonuclease, and lysozyme to the model thermally responsive mixed SAM were examined using AFM. All six proteins possessed adhesion to the pure component alkyl thiol, in

  12. A note on thermal activation

    CERN Document Server

    Boyanovsky, D; Lee, D S; Silva, J P; Daniel Boyanovsky; Richard Holman; Da-Shin Lee; Joao P Silva

    1994-01-01

    Thermal activation is mediated by field configurations that correspond to saddle points of the energy functional. The rate of probability flow along the unstable functional directions, i.e the activation rate, is usually obtained from the imaginary part of a suitable analytic continuation of the equilibrium free energy. In this note we provide a real-time, non-equilibrium interpretation of this imaginary part which is analogous to the real-time interpretation of the imaginary part of the one-loop effective potential in theories with symmetry breaking. We argue that in situations in which the system is strongly out of equilibrium the rate will be time dependent and illustrate this with an example.

  13. Methane Lunar Surface Thermal Control Test

    Science.gov (United States)

    Plachta, David W.; Sutherlin, Steven G.; Johnson, Wesley L.; Feller, Jeffrey R.; Jurns, John M.

    2012-01-01

    NASA is considering propulsion system concepts for future missions including human return to the lunar surface. Studies have identified cryogenic methane (LCH4) and oxygen (LO2) as a desirable propellant combination for the lunar surface ascent propulsion system, and they point to a surface stay requirement of 180 days. To meet this requirement, a test article was prepared with state-of-the-art insulation and tested in simulated lunar mission environments at NASA GRC. The primary goals were to validate design and models of the key thermal control technologies to store unvented methane for long durations, with a low-density high-performing Multi-layer Insulation (MLI) system to protect the propellant tanks from the environmental heat of low Earth orbit (LEO), Earth to Moon transit, lunar surface, and with the LCH4 initially densified. The data and accompanying analysis shows this storage design would have fallen well short of the unvented 180 day storage requirement, due to the MLI density being much higher than intended, its substructure collapse, and blanket separation during depressurization. Despite the performance issue, insight into analytical models and MLI construction was gained. Such modeling is important for the effective design of flight vehicle concepts, such as in-space cryogenic depots or in-space cryogenic propulsion stages.

  14. Amphoteric surface active agents

    Directory of Open Access Journals (Sweden)

    Eissa, A.M. F.

    1995-10-01

    Full Text Available 2-[trimethyl ammonium, triethyl ammonium, pyridinium and 2-amino pyridinium] alkanoates, four series of surface active agents containing carbon chain C12, C14, C16 and C18carbon atoms, were prepared. Their structures were characterized by microanalysis, infrared (IR and nuclear magnetic resonance (NMR. Surface and interfacial tension, Krafft point, wetting time, emulsification power, foaming height and critical micelle concentration (cmc were determined and a comparative study was made between their chemical structure and surface active properties. Antimicrobial activity of these surfactants was also determined.

    Se prepararon cuatro series de agentes tensioactivos del tipo 2-[trimetil amonio, trietil amonio, piridinio y 2-amino piridinio] alcanoatos, que contienen cadenas carbonadas con C12, C14, C16 y C18 átomos de carbono.
    Se determinaron la tensión superficial e interfacial, el punto de Krafft, el tiempo humectante, el poder de emulsionamiento, la altura espumante y la concentración critica de miscela (cmc y se hizo un estudio comparativo entre la estructura química y sus propiedades tensioactivas. Se determinó también la actividad antimicrobiana de estos tensioactivos. Estas estructuras se caracterizaron por microanálisis, infrarrojo (IR y resonancia magnética nuclear (RMN.

  15. Autonomous Aerobraking Using Thermal Response Surface Analysis

    Science.gov (United States)

    Prince, Jill L.; Dec, John A.; Tolson, Robert H.

    2007-01-01

    Aerobraking is a proven method of significantly increasing the science payload that can be placed into low Mars orbits when compared to an all propulsive capture. However, the aerobraking phase is long and has mission cost and risk implications. The main cost benefit is that aerobraking permits the use of a smaller and cheaper launch vehicle, but additional operational costs are incurred during the long aerobraking phase. Risk is increased due to the repeated thermal loading of spacecraft components and the multiple attitude and propulsive maneuvers required for successful aerobraking. Both the cost and risk burdens can be significantly reduced by automating the aerobraking operations phase. All of the previous Mars orbiter missions that have utilized aerobraking have increasingly relied on onboard calculations during aerobraking. Even though the temperature of spacecraft components has been the limiting factor, operational methods have relied on using a surrogate variable for mission control. This paper describes several methods, based directly on spacecraft component maximum temperature, for autonomously predicting the subsequent aerobraking orbits and prescribing apoapsis propulsive maneuvers to maintain the spacecraft within specified temperature limits. Specifically, this paper describes the use of thermal response surface analysis in predicting the temperature of the spacecraft components and the corresponding uncertainty in this temperature prediction.

  16. Autonomous Aerobraking: Thermal Analysis and Response Surface Development

    Science.gov (United States)

    Dec, John A.; Thornblom, Mark N.

    2011-01-01

    A high-fidelity thermal model of the Mars Reconnaissance Orbiter was developed for use in an autonomous aerobraking simulation study. Response surface equations were derived from the high-fidelity thermal model and integrated into the autonomous aerobraking simulation software. The high-fidelity thermal model was developed using the Thermal Desktop software and used in all phases of the analysis. The use of Thermal Desktop exclusively, represented a change from previously developed aerobraking thermal analysis methodologies. Comparisons were made between the Thermal Desktop solutions and those developed for the previous aerobraking thermal analyses performed on the Mars Reconnaissance Orbiter during aerobraking operations. A variable sensitivity screening study was performed to reduce the number of variables carried in the response surface equations. Thermal analysis and response surface equation development were performed for autonomous aerobraking missions at Mars and Venus.

  17. Thermal instability of DLC film surface morphology - an AFM study

    Science.gov (United States)

    Maheswaran, R.; Thiruvadigal, D. John; Gopalakrishnan, C.

    2012-06-01

    The surface morphology of the DLC film during thermal annealing at particular temperature above the graphitization temperature shows blistering and buckling and also delaminates from the substrate. The DLC film shows poor thermal stability at higher temperature.

  18. Thermal slip for liquids at rough solid surfaces

    Science.gov (United States)

    Zhang, Chengbin; Chen, Yongping; Peterson, G. P.

    2014-06-01

    Molecular dynamics simulation is used to examine the thermal slip of liquids at rough solid surfaces as characterized by fractal Cantor structures. The temperature profiles, potential energy distributions, thermal slip, and interfacial thermal resistance are investigated and evaluated for a variety of surface topographies. In addition, the effects of liquid-solid interaction, surface stiffness, and boundary condition on thermal slip length are presented. Our results indicate that the presence of roughness expands the low potential energy regions in adjacent liquids, enhances the energy transfer at liquid-solid interface, and decreases the thermal slip. Interestingly, the thermal slip length and thermal resistance for liquids in contact with solid surfaces depends not only on the statistical roughness height, but also on the fractal dimension (i.e., topographical spectrum).

  19. Surface Active Components: Review

    Directory of Open Access Journals (Sweden)

    Z. Shafiei

    2014-03-01

    Full Text Available Biosurfactant or surface active components are produced by many different microorganisms. Biosurfactants are amphiphilic molecules with both hydrophilic and hydrophobic (generally hydrocarbon moieties that partition preferentially a within the interface between fluid phases with some other degrees of polarity and hydrogen bonding including oil/water or air/water interfaces. These properties render surfactants able to reducing surface and interfacial tension and forming microemulsion where hydrocarbons can solubilize in water or where water can solubilize in hydrocarbons, the majority of surfactants have gained importance in the fields of enhanced oil recovery, environmental bioremediation, food processing and pharmaceuticals. However, large-scale production of these molecules has not been realized as a result of low yields in production processes and high recovery and purification costs. This review article represents a classification of biosurfactant in addition to their microbial origin and effect of some nutrition and environmental factor for high production of biosurfactant. The nitrogen, carbon sources and environmental factors can make a difference key to the regulating biosurfactants synthesis Fascination with microbial surfactants have been steadily increasing recently because of advantages over the chemical surfactants for example environmentally friendly nature, lower toxicity, higher biodegradability, higher selectivity and specific gravity at extreme temperature, pH and salinity. For this reason the demand of biosurfactant are increasing day by day.

  20. Vegetation impact on the thermal regimes of the active layer and near-surface permafrost in the Greater Hinggan Mountains, Northeastern China

    Institute of Scientific and Technical Information of China (English)

    XiaoLi Chang; ShaoPeng Yu; HuiJun Jin; YanLin Zhang

    2014-01-01

    The ground temperature and active layer are greatly influenced by vegetation in the Greater Hinggan Mountains in Northeastern China. However, vegetation, as a complex system, is difficult to separate the influence of its different components on the ground thermal regime. In this paper, four vegetation types, including a Larix dahurica-Ledum palustre var. dilatatum-Bryum forest (P1), a L. dahurica-Betula fruticosa forest (P2), a L. dahurica-Carex tato forest (P3) in the China Forest Ecological Research Network Station in Genhe, and a Carex tato swamp (P4) at the permafrost observation site in Yitulihe, have been selected to study and compare their seasonal and annual influence on the ground thermal regime. Results show that the vegetation insulates the ground resulting in a relatively high ground temperature variability in the Carex tato swamp where there are no tree stands and shrubs when compared with three forested vegetation types present in the area. Vegetation thickness, structure, and coverage are the most important factors that determine the insulating prop-erties of the vegetation. In particular, the growth of ground cover, its water-holding capacity and ability to intercept snow exert a significant effect on the degree of insulation of the soil under the same vegetation.

  1. Surface and Electrical Properties of Electro-Coagulated Thermal Waste

    Science.gov (United States)

    Yesilkaya, S. S.; Okutan, M.; Içelli, O.; Yalçın, Z.

    2015-05-01

    The Electro-Coagulated Thermal Waste (ECTW) sample of the impedance spectroscopy investigation for electrical modulus and conductivity are presented. Electrical properties via temperature and frequency dependent impedance spectroscopy were investigated. Real and imaginary parts of electrical modulus were measured at various frequencies and a related Cole-Cole plot was acquired as well. The surface resistivity of the ECTW was measured by the four-point probe measurement technique, yielding a relatively high surface resistivity. As a result of this study, an effective building shielding material, which is a cost effective alternative, is proposed. The activation energy values were calculated from the Arrhenius plots at different frequencies. The transition region in this plot may be attributed to activation of ionic conductivity at lower temperatures.

  2. Near-field thermal imaging of nanostructured surfaces

    Science.gov (United States)

    Kittel, A.; Wischnath, U. F.; Welker, J.; Huth, O.; Rüting, F.; Biehs, S.-A.

    2008-11-01

    We show that a near-field scanning thermal microscope, which essentially detects the local density of states of the thermally excited electromagnetic modes at nanometer distances from some material, can be employed for nanoscale imaging of structures on that material's surface. This finding is explained theoretically by an approach which treats the surface structure perturbatively.

  3. Understanding Thermal Equilibrium through Activities

    Science.gov (United States)

    Pathare, Shirish; Huli, Saurabhee; Nachane, Madhura; Ladage, Savita; Pradhan, Hemachandra

    2015-01-01

    Thermal equilibrium is a basic concept in thermodynamics. In India, this concept is generally introduced at the first year of undergraduate education in physics and chemistry. In our earlier studies (Pathare and Pradhan 2011 "Proc. episteme-4 Int. Conf. to Review Research on Science Technology and Mathematics Education" pp 169-72) we…

  4. Observed Asteroid Surface Area in the Thermal Infrared

    Science.gov (United States)

    Nugent, C. R.; Mainzer, A.; Masiero, J.; Wright, E. L.; Bauer, J.; Grav, T.; Kramer, E.; Sonnett, S.

    2017-02-01

    The rapid accumulation of thermal infrared observations and shape models of asteroids has led to increased interest in thermophysical modeling. Most of these infrared observations are unresolved. We consider what fraction of an asteroid’s surface area contributes the bulk of the emitted thermal flux for two model asteroids of different shapes over a range of thermal parameters. The resulting observed surface in the infrared is generally more fragmented than the area observed in visible wavelengths, indicating high sensitivity to shape. For objects with low values of the thermal parameter, small fractions of the surface contribute the majority of thermally emitted flux. Calculating observed areas could enable the production of spatially resolved thermal inertia maps from non-resolved observations of asteroids.

  5. Laser pulse heating of surfaces and thermal stress analysis

    CERN Document Server

    Yilbas, Bekir S; Al-Aqeeli, Nasser; Al-Qahtani, Hussain M

    2013-01-01

    This book introduces laser pulse heating and thermal stress analysis in materials surface. Analytical temperature treatments and stress developed in the surface region are also explored. The book will help the reader analyze the laser induced stress in the irradiated region and presents solutions for the stress field. Detailed thermal stress analysis in different laser pulse heating situations and different boundary conditions are also presented. Written for surface engineers.

  6. Variable Surface Area Thermal Radiator Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Due to increased complexity of spacecraft and longer expected life, more sophisticated and complex thermal management schemes are needed that will be capable of...

  7. Thermal properties of alkali-activated aluminosilicates

    Science.gov (United States)

    Florian, Pavel; Valentova, Katerina; Fiala, Lukas; Zmeskal, Oldrich

    2017-07-01

    The paper is focused on measurements and evaluation of thermal properties of alkali-activated aluminosilicates (AAA) with various carbon admixtures. Such composites consisting of blast-furnace slag, quartz sand, water glass as alkali activator and small amount of electrically conductive carbon admixture exhibit better electric and thermal properties than the reference material. Such enhancement opens up new practical applications, such as designing of snow-melting, de-icing or self-sensing systems that do not need any external sensors to detect current condition of building material. Thermal properties of the studied materials were measured by the step-wise transient method and mutually compared.

  8. Patterns of thermal constraint on ectotherm activity.

    Science.gov (United States)

    Gunderson, Alex R; Leal, Manuel

    2015-05-01

    Thermal activity constraints play a major role in many aspects of ectotherm ecology, including vulnerability to climate change. Therefore, there is strong interest in developing general models of the temperature dependence of activity. Several models have been put forth (explicitly or implicitly) to describe such constraints; nonetheless, tests of the predictive abilities of these models are lacking. In addition, most models consider activity as a threshold trait instead of considering continuous changes in the vigor of activity among individuals. Using field data for a tropical lizard (Anolis cristatellus) and simulations parameterized by our observations, we determine how well various threshold and continuous-activity models match observed activity patterns. No models accurately predicted activity under all of the thermal conditions that we considered. In addition, simulations showed that the performance of threshold models decreased as temperatures increased, which is a troubling finding given the threat of global climate change. We also find that activity rates are more sensitive to temperature than are the physiological traits often used as a proxy for fitness. We present a model of thermal constraint on activity that integrates aspects of both the threshold model and the continuous-activity model, the general features of which are supported by activity data from other species. Overall, our results demonstrate that greater attention should be given to fine-scale patterns of thermal constraint on activity.

  9. Thermal surveillance of active volcanoes

    Science.gov (United States)

    Friedman, J. D. (Principal Investigator)

    1973-01-01

    The author has identified the following significant results. There are three significant scientific results of the discovery of 48 pinpoint anomalies on the upper flanks of Mt. Rainier: (1) Many of these points may actually be the location of fumarolic vapor emission or warm ground considerably below the summit crater. (2) Discovery of these small anomalies required specific V/H scanner settings for precise elevation on Mt. Rainier's flank, to avoid smearing the anomalies to the point of nonrecognition. Several past missions flown to map the thermal anomalies of the summit area did not/detect the flank anomalies. (3) This illustrates the value of the aerial IR scanner as a geophysical tool suited to specific problem-oriented missions, in contrast to its more general value in a regional or reconnaissance anomaly-mapping role.

  10. Emergent geometry, thermal CFT and surface/state correspondence

    Science.gov (United States)

    Gan, Wen-Cong; Shu, Fu-Wen; Wu, Meng-He

    2017-09-01

    We study a conjectured correspondence between any codimension-two convex surface and a quantum state (SS-duality for short). By applying thermofield double formalism to the SS-duality, we show that thermal geometries naturally emerge as a result of hidden quantum entanglement between two boundary CFTs. We therefore propose a general framework to emerge the thermal geometry from CFT at finite temperature, without knowing many details about the thermal CFT. As an example, the case of 2d CFT is considered. We calculate its information metric and show that it is either BTZ black hole or thermal AdS as expected.

  11. Decorative Surfaces Obtained through Thermal Zyncking

    Directory of Open Access Journals (Sweden)

    Tamara Radu

    2010-06-01

    Full Text Available The surface morphology of the galvanized sheets is formed after the solidification of the melted metal, carried along the carrier strap during its extraction from the zinc bath. The surface layer quality depends on the fluidity of the melting, on its superficial tension and on the solidification characteristics, according to the chemical composition of the melting. The elements of micro-alloys can improve the surface of galvanized steel with qualities such as: uniformity, texture, luminosity. Depending on the combination elements of micro-alloying the surface can have different types of metallic layers with an important effect on the coating morphology. The research we made revealed the important effect it had for alloys with Al, Sn, Bi, Pb on the coating layer morphology.

  12. Hybrid energy harvesting using active thermal backplane

    Science.gov (United States)

    Kim, Hyun-Wook; Lee, Dong-Gun

    2016-04-01

    In this study, we demonstrate the concept of a new hybrid energy harvesting system by combing solar cells with magneto-thermoelectric generator (MTG, i.e., thermal energy harvesting). The silicon solar cell can easily reach high temperature under normal operating conditions. Thus the heated solar cell becomes rapidly less efficient as the temperature of solar cell rises. To increase the efficiency of the solar cell, air or water-based cooling system is used. To surpass conventional cooling devices requiring additional power as well as large working space for air/water collectors, we develop a new technology of pairing an active thermal backplane (ATB) to solar cell. The ATB design is based on MTG technology utilizing the physics of the 2nd order phase transition of active ferromagnetic materials. The MTG is cost-effective conversion of thermal energy to electrical energy and is fundamentally different from Seebeck TEG devices. The ATB (MTG) is in addition to being an energy conversion system, a very good conveyor of heat through both conduction and convection. Therefore, the ATB can provide dual-mode for the proposed hybrid energy harvesting. One is active convective and conductive cooling for heated solar cell. Another is active thermal energy harvesting from heat of solar cell. These novel hybrid energy harvesting device have potentially simultaneous energy conversion capability of solar and thermal energy into electricity. The results presented can be used for better understanding of hybrid energy harvesting system that can be integrated into commercial applications.

  13. Active thermal testing of moisture in bricks

    Science.gov (United States)

    Bison, Paolo G.; Bressan, Chiara; Grinzato, Ermanno G.; Marinetti, Sergio; Vavilov, Vladimir P.

    1993-04-01

    Measurement by active thermal testing of effusivity on porous moistened material is analyzed. Moistened bricks show that thermal properties of this porous solid depend on water content. Various solutions of the heat transfer problem are taken into account and approximations introduced to simplify the data reduction are discussed. Error analysis is also considered to justify the adoption of relative technique. Errors analysis speaks strongly in favor of reference method which allows to avoid the measurement of incident energy and optical properties of a specimen. This procedure allows to introduce a rather simple expression to extract moisture values from one-side thermal test. Diffusivity measurement trough flash method is proposed to determine the influence of moisture on the variation of thermal conductivity.

  14. Ground-based measurement of surface temperature and thermal emissivity

    Science.gov (United States)

    Owe, M.; Van De Griend, A. A.

    1994-01-01

    Motorized cable systems for transporting infrared thermometers have been used successfully during several international field campaigns. Systems may be configured with as many as four thermal sensors up to 9 m above the surface, and traverse a 30 m transect. Ground and canopy temperatures are important for solving the surface energy balance. The spatial variability of surface temperature is often great, so that averaged point measurements result in highly inaccurate areal estimates. The cable systems are ideal for quantifying both temporal and spatial variabilities. Thermal emissivity is also necessary for deriving the absolute physical temperature, and measurements may be made with a portable measuring box.

  15. Thermal activation of serpentine for adsorption of cadmium

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Chun-Yan [College of Land and Environment, Shenyang Agricultural University, Shenyang (China); College of Chemistry, Chemical Engineering and Food Safety, Bohai University, Jinzhou (China); Liang, Cheng-Hua, E-mail: liang110161@163.com [College of Land and Environment, Shenyang Agricultural University, Shenyang (China); Yin, Yan [Institute of Applied Ecology, Chinese Academy of Sciences, Shenyang (China); Du, Li-Yu [College of Land and Environment, Shenyang Agricultural University, Shenyang (China)

    2017-05-05

    Highlights: • Thermal activated serpentine was prepared by changing heated temperature. • Thermal activated serpentine exhibited excellent adsorption behavior for cadmium. • The adsorption mechanisms could be explained as formation of CdCO{sub 3} and Cd(OH){sub 2}. • The adsorption obeyed Langmuir model and pseudo second order kinetics model. - Abstract: Thermal activated serpentine with high adsorption capacity for heavy metals was prepared. The batch experiment studies were conducted to evaluate the adsorption performance of Cd{sup 2+} in aqueous solution using thermal activated serpentine as adsorbent. These samples before and after adsorption were characterized by XRD, FT-IR, SEM, XPS, and N{sub 2} adsorption-desorption at low temperature. It was found that serpentine with layered structure transformed to forsterite with amorphous structure after thermal treatment at over 700 °C, while the surface area of the samples was increased with activated temperature and the serpentine activated at 700 °C (S-700) presented the largest surface area. The pH of solution after adsorption was increased in different degrees due to hydrolysis of MgO in serpentine, resulting in enhancing adsorption of Cd{sup 2+}. The S-700 exhibited the maximum equilibrium adsorption capacity (15.21 mg/g), which was 2 times more than pristine serpentine. Langmuir isotherm was proved to describe the equilibrium adsorption data better than Freundlich isotherm and pseudo second order kinetics model could fit the adsorption kinetics processes well. Based on the results of characterization with XPS and XRD, the adsorption mechanisms could be explained as primarily formation of CdCO{sub 3} and Cd(OH){sub 2} precipitation on the surface of serpentine.

  16. Human suspicious activity recognition in thermal infrared video

    Science.gov (United States)

    Hossen, Jakir; Jacobs, Eddie; Chowdhury, Fahmida K.

    2014-10-01

    Detecting suspicious behaviors is important for surveillance and monitoring systems. In this paper, we investigate suspicious activity detection in thermal infrared imagery, where human motion can be easily detected from the background regardless of the lighting conditions and colors of the human clothing and surfaces. We use locally adaptive regression kernels (LARK) as patch descriptors, which capture the underlying local structure of the data exceedingly well, even in the presence of significant distortions. Patch descriptors are generated for each query patch and for each database patch. A statistical approach is used to match the query activity with the database to make the decision of suspicious activity. Human activity videos in different condition such as, walking, running, carrying a gun, crawling, and carrying backpack in different terrains were acquired using thermal infrared camera. These videos are used for training and performance evaluation of the algorithm. Experimental results show that the proposed approach achieves good performance in suspicious activity recognition.

  17. 3D SURFACE GENERATION FROM AERIAL THERMAL IMAGERY

    Directory of Open Access Journals (Sweden)

    B. Khodaei

    2015-12-01

    Full Text Available Aerial thermal imagery has been recently applied to quantitative analysis of several scenes. For the mapping purpose based on aerial thermal imagery, high accuracy photogrammetric process is necessary. However, due to low geometric resolution and low contrast of thermal imaging sensors, there are some challenges in precise 3D measurement of objects. In this paper the potential of thermal video in 3D surface generation is evaluated. In the pre-processing step, thermal camera is geometrically calibrated using a calibration grid based on emissivity differences between the background and the targets. Then, Digital Surface Model (DSM generation from thermal video imagery is performed in four steps. Initially, frames are extracted from video, then tie points are generated by Scale-Invariant Feature Transform (SIFT algorithm. Bundle adjustment is then applied and the camera position and orientation parameters are determined. Finally, multi-resolution dense image matching algorithm is used to create 3D point cloud of the scene. Potential of the proposed method is evaluated based on thermal imaging cover an industrial area. The thermal camera has 640×480 Uncooled Focal Plane Array (UFPA sensor, equipped with a 25 mm lens which mounted in the Unmanned Aerial Vehicle (UAV. The obtained results show the comparable accuracy of 3D model generated based on thermal images with respect to DSM generated from visible images, however thermal based DSM is somehow smoother with lower level of texture. Comparing the generated DSM with the 9 measured GCPs in the area shows the Root Mean Square Error (RMSE value is smaller than 5 decimetres in both X and Y directions and 1.6 meters for the Z direction.

  18. Drop formation by thermal fluctuations at an ultralow surface tension.

    Science.gov (United States)

    Hennequin, Y; Aarts, D G A L; van der Wiel, J H; Wegdam, G; Eggers, J; Lekkerkerker, H N W; Bonn, Daniel

    2006-12-15

    We present experimental evidence that drop breakup is caused by thermal noise in a system with a surface tension that is more than 10(6) times smaller than that of water. We observe that at very small scales classical hydrodynamics breaks down and the characteristic signatures of pinch-off due to thermal noise are observed. Surprisingly, the noise makes the drop size distribution more uniform, by suppressing the formation of satellite droplets of the smallest sizes. The crossover between deterministic hydrodynamic motion and stochastic thermally driven motion has repercussions for our understanding of small-scale hydrodynamics, important in many problems such as micro- or nanofluidics and interfacial singularities.

  19. Geothermal reservoir characterization through active thermal testing

    Science.gov (United States)

    Jung, Martin; Klepikova, Maria; Jalali, Mohammadreza; Fisch, Hansruedi; Loew, Simon; Amann, Florian

    2016-04-01

    Development and deployment of Enhanced Geothermal Systems (EGS) as renewable energy resources are part of the Swiss Energy Strategy 2050. To pioneer further EGS projects in Switzerland, a decameter-scale in-situ hydraulic stimulation and circulation (ISC) experiment has been launched at the Grimsel Test Site (GTS). The experiments are hosted in a low fracture density volume of the Grimsel granodiorite, similar to those expected at the potential enhanced geothermal system sites in the deep basement rocks of Northern Switzerland. One of the key goals of this multi-disciplinary experiment is to provide a pre- and post-stimulation characterization of the hydraulic and thermal properties of the stimulated fracture network with high resolution and to determine natural structures controlling the fluid flow and heat transport. Active thermal tests including thermal dilution tests and heat tracer tests allow for investigation of groundwater fluid flow and heat transport. Moreover, the spatial and temporal integrity of distributed temperature sensing (DTS) monitoring upgrades the potential and applicability of thermal tests in boreholes (e.g. Read et al., 2013). Here, we present active thermal test results and discuss the advantages and limitations of this method compared to classical approaches (hydraulic packer tests, solute tracer tests, flowing fluid electrical conductivity logging). The experimental tests were conducted in two boreholes intersected by a few low to moderately transmissive fault zones (fracture transmissivity of about 1E-9 m2/s - 1E-7 m2/s). Our preliminary results show that even in low-permeable environments active thermal testing may provide valuable insights into groundwater and heat transport pathways. Read T., O. Bour, V. Bense, T. Le Borgne, P. Goderniaux, M.V. Klepikova, R. Hochreutener, N. Lavenant, and V. Boschero (2013), Characterizing groundwater flow and heat transport in fractured rock using Fiber-Optic Distributed Temperature Sensing

  20. Local thermal properties of the surface of Vesta

    Science.gov (United States)

    Capria, M. T.; Tosi, F.; Capaccioni, F.; De Sanctis, M. C.; Palomba, E.; Ammannito, E.; Carraro, F.; Fonte, S.; Titus, T. N.; Combe, J.-P.; Toplis, M.; Sunshine, J.; Fulchignoni, M.; Russel, C. T.; Raymond, C. A.

    2012-04-01

    Temperature information has been obtained from the Dawn/VIR (Visible InfraRed imaging spectrometer) spectra acquired during the Vesta campaign. When combined with a thermophysical model, these temperatures can be used to derive surface thermal properties. Thermal properties are sensitive to several physical characteristics of the surface that are not all spatially resolved. Thus, the derivation of surface temperatures and thermal inertia can lead to the characterization of surface and sub-surface properties of Vesta and the determination of regolith properties. The model we are using solves the heat conduction equation and provide the temperature as a function of thermal conductivity, albedo, emissivity, density and specific heat. The model is applied to the actual shape of Vesta: for any given location, characterized by a well-defined illumination condition and a given UTC time to compute the thermal inertia that results in model temperatures providing a best-fit to surface temperatures as retrieved by VIR. The model has been already applied to the first Vesta full-disk data to derive the global average thermal inertia of Vesta. The values obtained are typical of fine-grained, unconsolidated materials (i.e. dust) and suggest a surface in which a dust layer is wide-spread on coarser regolith. The model is now being applied on small regions of the surface of Vesta. Specific regions are selected because they are interesting for some reason or appear different from the surroundings, such as, for example, dark and bright spots and other peculiar features. Given a location, the thermophysical code is applied until the obtained temperatures are matching (best-fit techniques are used) the temperatures derived from the VIR spectra. The thermal inertia, thermal conductivity, albedo and roughness values are then assumed to be characterizing the location under analysis. The results of the model must be carefully checked and interpreted by taking into account the context (from

  1. Active Free Surface Density Maps

    Science.gov (United States)

    Çelen, S.

    2016-10-01

    Percolation problems were occupied to many physical problems after their establishment in 1957 by Broadbent and Hammersley. They can be used to solve complex systems such as bone remodeling. Volume fraction method was adopted to set some algorithms in the literature. However, different rate of osteoporosis could be observed for different microstructures which have the same mass density, mechanical stimuli, hormonal stimuli and nutrition. Thus it was emphasized that the bone might have identical porosity with different specific surfaces. Active free surface density of bone refers the used total area for its effective free surface. The purpose of this manuscript is to consolidate a mathematical approach which can be called as “active free surface density maps” for different surface patterns and derive their formulations. Active free surface density ratios were calculated for different Archimedean lattice models according to Helmholtz free energy and they were compared with their site and bond percolation thresholds from the background studies to derive their potential probability for bone remodeling.

  2. Thermal Diffusion Processes in Metal-Tip-Surface Interactions: Contact Formation and Adatom Mobility

    DEFF Research Database (Denmark)

    Sørensen, Mads Reinholdt; Jacobsen, Karsten Wedel; Jonsson, Hannes

    1996-01-01

    We have carried out computer simulations to identify and characterize various thermally activated atomic scale processes that can play an important role in room temperature experiments where a metal tip is brought close to a metal surface. We find that contact formation between the tip...... and the surface can occur by a sequence of atomic hop and exchange processes which become active on a millisecond time scale when the tip is about 3-5 Angstrom from the surface. Adatoms on the surface are stabilized by the presence of the tip and energy barriers for diffusion processes in the region under the tip...

  3. Modeling the impact of solid surfaces in thermal degradation processes

    NARCIS (Netherlands)

    Tuma, Christian; Laino, Teodoro; Martin, Elyette; Stolz, Steffen; Curioni, Alessandro

    2013-01-01

    First-principles simulations are carried out to generate reaction profiles for the initial steps of the thermal decomposition of glycerol, propylene glycol, and triacetin over the surfaces of pseudo-amorphous carbon and silica, crystalline zirconia [001], and crystalline alumina (0001).

  4. Sea surface temperature mapping using a thermal infrared scanner

    Digital Repository Service at National Institute of Oceanography (India)

    RameshKumar, M.R.; Pandya, R.M.; Mathur, K.M.; Charyulu, R.J.K.; Rao, L.V.G.

    1 metre water column below the sea surface. A thermal infrared scanner developed by the Space Applications Centre (ISRO), Ahmedabad was operated on board R.V. Gaveshani in April/May 1984 for mapping SST over the eastern Arabian Sea. SST values...

  5. Nano-Localized Thermal Analysis and Mapping of Surface and Sub-Surface Thermal Properties Using Scanning Thermal Microscopy (SThM).

    Science.gov (United States)

    Pereira, Maria J; Amaral, Joao S; Silva, Nuno J O; Amaral, Vitor S

    2016-12-01

    Determining and acting on thermo-physical properties at the nanoscale is essential for understanding/managing heat distribution in micro/nanostructured materials and miniaturized devices. Adequate thermal nano-characterization techniques are required to address thermal issues compromising device performance. Scanning thermal microscopy (SThM) is a probing and acting technique based on atomic force microscopy using a nano-probe designed to act as a thermometer and resistive heater, achieving high spatial resolution. Enabling direct observation and mapping of thermal properties such as thermal conductivity, SThM is becoming a powerful tool with a critical role in several fields, from material science to device thermal management. We present an overview of the different thermal probes, followed by the contribution of SThM in three currently significant research topics. First, in thermal conductivity contrast studies of graphene monolayers deposited on different substrates, SThM proves itself a reliable technique to clarify the intriguing thermal properties of graphene, which is considered an important contributor to improve the performance of downscaled devices and materials. Second, SThM's ability to perform sub-surface imaging is highlighted by thermal conductivity contrast analysis of polymeric composites. Finally, an approach to induce and study local structural transitions in ferromagnetic shape memory alloy Ni-Mn-Ga thin films using localized nano-thermal analysis is presented.

  6. HIGH VELOCITY THERMAL GUN FOR SURFACE PREPARATION AND TREATMENT

    Directory of Open Access Journals (Sweden)

    I.A. Gorlach

    2012-01-01

    Full Text Available Many surface preparation and treatment processes utilise compressed air to propel particles against surfaces in order to clean and treat them. The effectiveness of the processes depends on the velocity of the particles, which in turn depends on the pressure of the compressed air. This paper describes a thermal gun built on the principles of High Velocity Air Fuel (HVAF and High Velocity Oxy Fuel (HVOF processes. The designed apparatus can be used for abrasive blasting, coating of surfaces, cutting of rocks, removing rubber from mining equipment, cleaning of contaminations etc.

  7. Emergent geometry, thermal CFT and surface/state correspondence

    CERN Document Server

    Gan, Wen-Cong; Wu, Meng-He

    2016-01-01

    We study a conjectured correspondence between any codimension two convex surface and a quantum state (SS-duality for short). By generalizing thermofield double formalism to continuum version of the multi-scale entanglement renormalization ansatz (cMERA) and using the SS-duality, we propose a general framework to emerge the thermal geometry from CFT at finite temperature. As an example, the case of $2d$ CFT is considered carefully. We calculate its information metric and show that it is the BTZ black hole or the thermal AdS as expectation.

  8. Dual active surface heat flux gage probe

    Science.gov (United States)

    Liebert, Curt H.; Kolodziej, Paul

    1995-02-01

    A unique plug-type heat flux gage probe was tested in the NASA Ames Research Center 2x9 turbulent flow duct facility. The probe was fabricated by welding a miniature dual active surface heat flux gage body to the end of a hollow metal cylindrical bolt containing a metal inner tube. Cooling air flows through the inner tube, impinges onto the back of the gage body and then flows out through the annulus formed between the inner tube and the hollow bolt wall. Heat flux was generated in the duct facility with a Huels arc heater. The duct had a rectangular cross section and one wall was fabricated from 2.54 centimeter thick thermal insulation rigid surface material mounted onto an aluminum plate. To measure heat flux, the probe was inserted through the plate and insulating materials with the from of the gage located flush with the hot gas-side insulation surface. Absorbed heat fluxes measured with the probe were compared with absorbed heat fluxes measured with six water-cooled reference calorimeters. These calorimeters were located in a water-cooled metal duct wall which was located across from the probe position. Correspondence of transient and steady heat fluxes measured with the reference calorimeters and heat flux gage probe was generally within a satisfactory plus or minus 10 percent. This good correspondence was achieved even though the much cooler probe caused a large surface temperature disruption of 1000K between the metal gage and the insulation. However, this temperature disruption did not seriously effect the accuracy of the heat flux measurement. A current application for dual active surface heat flux gages is for transient and steady absorbed heat flux, surface temperature and heat transfer coefficient measurements on the surface of an oxidizer turbine inlet deflector operating in a space shuttle test bed engine.

  9. Thermal activation in boundary lubricated friction

    Energy Technology Data Exchange (ETDEWEB)

    Michael, P.C. [Francis Bitter National Magnet Lab. and Dept. of Mechanical Engineering, Massachusetts Inst. of Tech., Cambridge, MA (United States); Rabinowicz, E. [Francis Bitter National Magnet Lab. and Dept. of Mechanical Engineering, Massachusetts Inst. of Tech., Cambridge, MA (United States); Iwasa, Y. [Francis Bitter National Magnet Lab. and Dept. of Mechanical Engineering, Massachusetts Inst. of Tech., Cambridge, MA (United States)

    1996-05-01

    The friction coefficients for copper pairs lubricated with fatty acids and fluorinated fatty acids have been measured over a wide range of sliding speeds and temperatures. Sliding speeds in the range 10{sup -7}-10{sup -2} m s{sup -1} and temperatures in the range 4.2-300 K were used. The friction coefficients near 300 K are generally low and increase with sliding speed, while the friction coefficients at low temperatures are markedly higher and relatively independent of velocity. Each lubricant`s friction vs. velocity behavior over the temperature range 150-300 K can be described by a friction-velocity master curve derived from a thermal activation model for the lubricant`s shear strength. The activation energies deduced from this friction model are identical to those obtained in the same temperature range for a vibrational mode associated with low temperature mechanical relaxations in similarly structured polymers. These results suggest that thermally activated interfacial shear is responsible for the fatty acids` positive-sloped friction vs. velocity characteristics at low sliding speeds near room temperature. (orig.)

  10. Determination of thermal/dynamic characteristics of lava flow from surface thermal measurements

    Science.gov (United States)

    Ismail-Zadeh, Alik; Melnik, Oleg; Korotkii, Alexander; Tsepelev, Igor; Kovtunov, Dmitry

    2016-04-01

    Rapid development of ground based thermal cameras, drones and satellite data allows getting repeated thermal images of the surface of the lava flow. Available instrumentation allows getting a large amount of data during a single lava flow eruption. These data require development of appropriate quantitative techniques to link subsurface dynamics with observations. We present a new approach to assimilation of thermal measurements at lava's surface to the bottom of the lava flow to determine lava's thermal and dynamic characteristics. Mathematically this problem is reduced to solving an inverse boundary problem. Namely, using known conditions at one part of the model boundary we determine the missing condition at the remaining part of the boundary. Using an adjoint method we develop a numerical approach to the mathematical problem based on the determination of the missing boundary condition and lava flow characteristics. Numerical results show that in the case of smooth input data lava temperature and velocity can be determined with a high accuracy. A noise imposed on the smooth input data results in a less accurate solution, but still acceptable below some noise level. The proposed approach to assimilate measured data brings an opportunity to estimate thermal budget of the lava flow.

  11. Flue Gas Desulfurization by Mechanically and Thermally Activated Sodium Bicarbonate

    Directory of Open Access Journals (Sweden)

    Walawska Barbara

    2014-09-01

    Full Text Available This paper presents the results of study on structural parameters (particle size, surface area, pore volume and the sorption ability of mechanically and thermally activated sodium bicarbonate. The sorption ability of the modified sorbent was evaluated by: partial and overall SO2 removal efficiency, conversion rate, normalized stoichiometric ratio (NSR. Sodium bicarbonate was mechanically activated by various grinding techniques, using three types of mills: fluid bed opposed jet mill, fine impact mill and electromagnetic mill, differing in grinding technology. Grounded sorbent was thermally activated, what caused a significant development of surface area. During the studies of SO2 sorption, a model gas with a temperature of 300°C, of composition: sulfur dioxide at a concentration of 6292 mg/mn3, oxygen, carbon dioxide and nitrogen as a carrier gas, was used. The best development of surface area and the highest SO2 removal efficiency was obtained for the sorbent treated by electromagnetic grinding, with simultaneous high conversion rate.

  12. THERMAL FRACTURE OF FUNCTIONALLY GRADED PLATE WITH PARALLEL SURFACE CRACKS

    Institute of Scientific and Technical Information of China (English)

    Yuezhong Feng; Zhihe Jin

    2009-01-01

    This work examines the fracture behavior of a functionally graded material (FGM) plate containing parallel surface cracks with alternating lengths subjected to a thermal shock. The thermal stress intensity factors (TSIFs) at the tips of long and short cracks are calculated using a singular integral equation technique. The critical thermal shock △T_c that causes crack initiation is calculated using a stress intensity factor criterion. Numerical examples of TSIFs and △T_c for an Al_2O_3/Si_3N_4 FGM plate are presented to illustrate the effects of thermal property gradation, crack spacing and crack length ratio on the TSIFs and △T_c. It is found that for a given crack length ratio, the TSIFs at the tips of both long and short cracks can be reduced significantly and △T_c can be enhanced by introducing appropriate material gradation. The TSIFs also decrease dramatically with a decrease in crack spacing. The TSIF at the tips of short cracks may be higher than that for the long cracks under certain crack geometry conditions. Hence, the short cracks instead of long cracks may first start to grow under the thermal shock loading.

  13. Improving Energy Efficiency In Thermal Oil Recovery Surface Facilities

    Energy Technology Data Exchange (ETDEWEB)

    Murthy Nadella, Narayana

    2010-09-15

    Thermal oil recovery methods such as Cyclic Steam Stimulation (CSS), Steam Assisted Gravity Drainage (SAGD) and In-situ Combustion are being used for recovering heavy oil and bitumen. These processes expend energy to recover oil. The process design of the surface facilities requires optimization to improve the efficiency of oil recovery by minimizing the energy consumption per barrel of oil produced. Optimization involves minimizing external energy use by heat integration. This paper discusses the unit processes and design methodology considering thermodynamic energy requirements and heat integration methods to improve energy efficiency in the surface facilities. A design case study is presented.

  14. Thermal analysis of dry eye subjects and the thermal impulse perturbation model of ocular surface.

    Science.gov (United States)

    Zhang, Aizhong; Maki, Kara L; Salahura, Gheorghe; Kottaiyan, Ranjini; Yoon, Geunyoung; Hindman, Holly B; Aquavella, James V; Zavislan, James M

    2015-03-01

    In this study, we explore the usage of ocular surface temperature (OST) decay patterns to distinguished between dry eye patients with aqueous deficient dry eye (ADDE) and meibomian gland dysfunction (MGD). The OST profiles of 20 dry eye subjects were measured by a long-wave infrared thermal camera in a standardized environment (24 °C, and relative humidity (RH) 40%). The subjects were instructed to blink every 5 s after 20 ∼ 25 min acclimation. Exponential decay curves were fit to the average temperature within a region of the central cornea. We find the MGD subjects have both a higher initial temperature (p thermal impulse perturbation (TIP) model. We conclude that long-wave-infrared thermal imaging is a plausible tool in assisting with the classification of dry eye patient.

  15. Laser-induced thermal desorption of aniline from silica surfaces

    Science.gov (United States)

    Voumard, Pierre; Zenobi, Renato

    1995-10-01

    A complete study on the energy partitioning upon laser-induced thermal desorption of aniline from silica surfaces was undertaken. The measurements include characterization of the aniline-quartz adsorption system using temperature-programmed desorption, the extrapolation of quasiequilibrium desorption temperatures to the regime of laser heating rates on the order of 109-1010 K/s by computational means, measurement of the kinetic energy distributions of desorbing aniline using a pump-probe method, and the determination of internal energies with resonance-enhanced multiphoton ionization spectroscopy. The measurements are compared to calculations of the surface temperature rise and the resulting desorption rates, based on a finite-difference mathematical description of pulsed laser heating. While the surface temperature of laser-heated silica reaches about 600-700 K at the time of desorption, the translational temperature of laser-desorbed aniline was measured to be Tkin=420±60 K, Tvib was 360±60 K, and Trot was 350±100 K. These results are discussed using different models for laser-induced thermal desorption from surfaces.

  16. Thermal annealing of laser damage precursors on fused silica surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Shen, N; Miller, P E; Bude, J D; Laurence, T A; Suratwala, T I; Steele, W A; Feit, M D; Wang, L L

    2012-03-19

    Previous studies have identified two significant precursors of laser damage on fused silica surfaces at fluenes below {approx} 35 J/cm{sup 2}, photoactive impurities in the polishing layer and surface fractures. In the present work, isothermal heating is studied as a means of remediating the highly absorptive, defect structure associated with surface fractures. A series of Vickers indentations were applied to silica surfaces at loads between 0.5N and 10N creating fracture networks between {approx} 10{micro}m and {approx} 50{micro}m in diameter. The indentations were characterized prior to and following thermal annealing under various times and temperature conditions using confocal time-resolved photo-luminescence (CTP) imaging, and R/1 optical damage testing with 3ns, 355nm laser pulses. Significant improvements in the damage thresholds, together with corresponding reductions in CTP intensity, were observed at temperatures well below the glass transition temperature (T{sub g}). For example, the damage threshold on 05.N indentations which typically initiates at fluences <8 J/cm{sup 2} could be improved >35 J/cm{sup 2} through the use of a {approx} 750 C thermal treatment. Larger fracture networks required longer or higher temperature treatment to achieve similar results. At an annealing temperature > 1100 C, optical microscopy indicates morphological changes in some of the fracture structure of indentations, although remnants of the original fracture and significant deformation was still observed after thermal annealing. This study demonstrates the potential of using isothermal annealing as a means of improving the laser damage resistance of fused silica optical components. Similarly, it provides a means of further understanding the physics associated with optical damage and related mitigation processes.

  17. Thermally activated depinning motion of contact lines in pseudopartial wetting.

    Science.gov (United States)

    Du, Lingguo; Bodiguel, Hugues; Colin, Annie

    2014-07-01

    We investigate pressure-driven motion of liquid-liquid menisci in circular tubes, for systems in pseudopartial wetting conditions. The originality of this type of wetting lies in the coexistence of a macroscopic contact angle with a wetting liquid film covering the solid surface. Focusing on small capillary numbers, we report observations of an apparent contact angle hysteresis at first sight similar to the standard partial wetting case. However, this apparent hysteresis exhibits original features. We observe very long transient regimes before steady state, up to several hundreds of seconds. Furthermore, in steady state, the velocities are nonzero, meaning that the contact line is not strongly pinned to the surface defects, but are very small. The velocity of the contact line tends to vanish near the equilibrium contact angle. These observations are consistent with the thermally activated depinning theory that has been proposed to describe partial wetting systems on disordered substrates and suggest that a single physical mechanism controls both the hysteresis (or the pinning) and the motion of the contact line. The proposed analysis leads to the conclusion that the depinning activated energy is lower with pseudopartial wetting systems than with partial wetting ones, allowing the direct observation of the thermally activated motion of the contact line.

  18. Local thermal property analysis by scanning thermal microscopy of an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment

    Energy Technology Data Exchange (ETDEWEB)

    Guo, F.A. [Suzhou Institute for Nonferrous Metals Processing Technology, No. 200 Shenxu Road, Suzhou Industrial Park, Suzhou 215021 (China) and Unite de Thermique et d' Analyse Physique, Laboratoire d' Energetique et d' Optique, Universite de Reims, BP 1039, 51687 Reims Cedex 2 (France)]. E-mail: guofuan@yahoo.com; JI, Y.L. [Suzhou Institute for Nonferrous Metals Processing Technology, No. 200 Shenxu Road, Suzhou Industrial Park, Suzhou 215021 (China); Trannoy, N. [Unite de Thermique et d' Analyse Physique, Laboratoire d' Energetique et d' Optique, Universite de Reims, BP 1039, 51687 Reims Cedex 2 (France); Lu, J. [LASMIS, Universite de Technologie de Troyes, 12 Rue Marie Curie, Troyes 10010 (France)

    2006-06-15

    Scanning thermal microscopy (SThM) was used to map thermal conductivity images in an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment (SMAT). It is found that the deformed surface layer shows different thermal conductivities that strongly depend on the grain size of the microstructure: the thermal conductivity of the nanostructured surface layer decreases obviously when compared with that of the coarse-grained matrix of the sample. The role of the grain boundaries in thermal conduction is analyzed in correlation with the heat conduction mechanism in pure metal. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

  19. Characters of surface deformation and surface wave in thermal capillary convection

    Institute of Scientific and Technical Information of China (English)

    DUAN; Li; KANG; Qi; HU; Wenrei

    2006-01-01

    In the field of fluid mechanics, free surface phenomena is one of the most important physical processes. In the present research work, the surface deformation and surface wave caused by temperature difference of sidewalls in a rectangular cavity have been investigated. The horizontal cross-section of the container is 52 mm×42 mm, and there is a silicon oil layer of height 3.5 mm in the experimental cavity. Temperature difference between the two side walls of the cavity is increased gradually, and the flow on the liquid layer will develop from stable convection to un-stable convection. An optical diagnostic system consisting of a modified Michelson interferometer and image processor has been developed for study of the surface deformation and surface wave of thermal capillary convection. The Fourier transformation method is used to interferometer fringe analysis. The quantitative results of surface deformation and surface wave have been calculated from a serial of the interference fringe patterns. The characters of surface deformation and surface wave have been obtained. They are related with temperature gradient and surface tension. Surface deformation is fluctuant with time, which shows the character of surface wave. The cycle period of the wave is 4.8 s, and the amplitudes are from 0 to 0.55 μm. The phase of the wave near the cool side of the cavity is opposite and correlative to that near the hot side. The present experiment proves that the surface wave of thermal capillary convection exists on liquid free surface, and it is wrapped in surface deformation.

  20. Photophysics of thermally activated delayed fluorescence molecules

    Science.gov (United States)

    Dias, Fernando B.; Penfold, Thomas J.; Monkman, Andrew P.

    2017-03-01

    Thermally activated delayed fluorescence (TADF) has recently emerged as one of the most attractive methods for harvesting triplet states in metal-free organic materials for application in organic light emitting diodes (OLEDs). A large number of TADF molecules have been reported in the literature with the purpose of enhancing the efficiency of OLEDs by converting non-emissive triplet states into emissive singlet states. TADF emitters are able to harvest both singlets and triplet states through fluorescence (prompt and delayed), the latter due to the thermally activated reverse intersystem crossing mechanism that allows up-conversion of low energy triplet states to the emissive singlet level. This allows otherwise pure fluorescent OLEDs to overcome their intrinsic limit of 25% internal quantum efficiency (IQE), which is imposed by the 1:3 singlet-triplet ratio arising from the recombination of charges (electrons and holes). TADF based OLEDS with IQEs close to 100% are now routinely fabricated in the green spectral region. There is also significant progress for blue emitters. However, red emitters still show relatively low efficiencies. Despite the significant progress that has been made in recent years, still significant challenges persist to achieve full understanding of the TADF mechanism and improve the stability of these materials. These questions need to be solved in order to fully implement TADF in OLEDs and expand their application to other areas. To date, TADF has been exploited mainly in the field of OLEDs, but applications in other areas, such as sensing and fluorescence microscopies, are envisaged. In this review, the photophysics of TADF molecules is discussed, summarising current methods to characterise these materials and the current understanding of the TADF mechanism in various molecular systems.

  1. Tailorable Surface Morphology of 3D Scaffolds by Combining Additive Manufacturing with Thermally Induced Phase Separation.

    Science.gov (United States)

    Di Luca, Andrea; de Wijn, Joost R; van Blitterswijk, Clemens A; Camarero-Espinosa, Sandra; Moroni, Lorenzo

    2017-08-01

    The functionalization of biomaterials substrates used for cell culture is gearing towards an increasing control over cell activity. Although a number of biomaterials have been successfully modified by different strategies to display tailored physical and chemical surface properties, it is still challenging to step from 2D substrates to 3D scaffolds with instructive surface properties for cell culture and tissue regeneration. In this study, additive manufacturing and thermally induced phase separation are combined to create 3D scaffolds with tunable surface morphology from polymer gels. Surface features vary depending on the gel concentration, the exchanging temperature, and the nonsolvent used. When preosteoblasts (MC-3T3 cells) are cultured on these scaffolds, a significant increase in alkaline phosphatase activity is measured for submicron surface topography, suggesting a potential role on early cell differentiation. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Characteristics of Turbulent Airflow Deduced from Rapid Surface Thermal Fluctuations: An Infrared Surface Anemometer

    Science.gov (United States)

    Aminzadeh, Milad; Breitenstein, Daniel; Or, Dani

    2017-07-01

    The intermittent nature of turbulent airflow interacting with the surface is readily observable in fluctuations of the surface temperature resulting from the thermal imprints of eddies sweeping the surface. Rapid infrared thermography has recently been used to quantify characteristics of the near-surface turbulent airflow interacting with the evaporating surfaces. We aim to extend this technique by using single-point rapid infrared measurements to quantify properties of a turbulent flow, including surface exchange processes, with a view towards the development of an infrared surface anemometer. The parameters for the surface-eddy renewal (α and β ) are inferred from infrared measurements of a single-point on the surface of a heat plate placed in a wind tunnel with prescribed wind speeds and constant mean temperatures of the surface. Thermally-deduced parameters are in agreement with values obtained from standard three-dimensional ultrasonic anemometer measurements close to the plate surface (e.g., α = 3 and β = 1/26 (ms)^{-1} for the infrared, and α = 3 and β = 1/19 (ms)^{-1} for the sonic-anemometer measurements). The infrared-based turbulence parameters provide new insights into the role of surface temperature and buoyancy on the inherent characteristics of interacting eddies. The link between the eddy-spectrum shape parameter α and the infrared window size representing the infrared field of view is investigated. The results resemble the effect of the sampling height above the ground in sonic anemometer measurements, which enables the detection of larger eddies with higher values of α . The physical basis and tests of the proposed method support the potential for remote quantification of the near-surface momentum field, as well as scalar-flux measurements in the immediate vicinity of the surface.

  3. Thermal instability of GaSb surface oxide

    Science.gov (United States)

    Tsunoda, K.; Matsukura, Y.; Suzuki, R.; Aoki, M.

    2016-05-01

    In the development of InAs/GaSb Type-II superlattice (T2SL) infrared photodetectors, the surface leakage current at the mesa sidewall must be suppressed. To achieve this requirement, both the surface treatment and the passivation layer are key technologies. As a starting point to design these processes, we investigated the GaSb oxide in terms of its growth and thermal stability. We found that the formation of GaSb oxide was very different from those of GaAs. Both Ga and Sb are oxidized at the surface of GaSb. In contrast, only Ga is oxidized and As is barely oxidized in the case of GaAs. Interestingly, the GaSb oxide can be formed even in DI water, which results in a very thick oxide film over 40 nm after 120 minutes. To examine the thermal stability, the GaSb native oxide was annealed in a vacuum and analyzed by XPS and Raman spectroscopy. These analyses suggest that SbOx in the GaSb native oxide will be reduced to metallic Sb above 300°C. To directly evaluate the effect of oxide instability on the device performance, a T2SL p-i-n photodetector was fabricated that has a cutoff wavelength of about 4 μm at 80 K. As a result, the surface leakage component was increased by the post annealing at 325°C. On the basis of these results, it is possible to speculate that a part of GaSb oxide on the sidewall surface will be reduced to metallic Sb, which acts as an origin of additional leakage current path.

  4. Abnormal thermal effects on the surface plasmon resonance of Ag nanoparticles on the surface of silicon

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Han; Ding, Ruiqiang [State Key Laboratory for Alternate Electrical Power System with Renewable Energy Sources, School of Renewable Energy, North China Electric Power University, Beijing 102206 (China); Li, Meicheng, E-mail: mcli@ncepu.edu.cn [State Key Laboratory for Alternate Electrical Power System with Renewable Energy Sources, School of Renewable Energy, North China Electric Power University, Beijing 102206 (China); Suzhou Institute, North China Electric Power University, Suzhou 215123 (China); Li, Yingfeng; Yang, Ganghai; Song, Dandan; Yu, Yue; Trevor, Mwenya [State Key Laboratory for Alternate Electrical Power System with Renewable Energy Sources, School of Renewable Energy, North China Electric Power University, Beijing 102206 (China)

    2015-06-01

    The thermal effects on the surface plasmon resonance (SPR) of Ag nanoparticles on the silicon surface have been studied. It is found that unusual blue shifts and narrowing of the SPR troughs occur as the temperature increases from 323 K to 363 K. At low temperature range (from 273 K to 323 K), the SPR troughs have the normal red shifts and broadening as in previous studies. The change of SPR is attributed to the thermal induced electron transport between particles and substrate, and is analyzed using samples with different particle sizes. This work reveals the mechanism of thermal effects on the plasmonic properties of Ag nanoparticles on the surface of silicon and offers useful information for designing of SPR devices. - Highlights: • Unusual blue shift of the SPR troughs is observed at 343 K. • Red shift of the SPR troughs is observed at 323 K. • The mechanism relies on the thermal induced surface electron transport. • Particle sizes play an important role in the change of the SPR troughs.

  5. Thermal hehavior of Surface Mounted Devices (SMD) packaging

    Science.gov (United States)

    Bloch, Werner; Moeller, Werner

    The thermal behavior of Surface Mounted Devices (SMD) packaging was investigated on an easily variable type. The effect of basic materials, chip carriers, and bonding, soldering, glueing and casting techniques was examined, considering the most important quantities, switching time and power. The test results show that cooling measures in the chip domain, such as chip bonding, chip casting, and chip carrier lining, are especially efficient for short switching times. The basic materials, even with heat sinks, become only important for longer switching times. The chip temperature of a conventional FR4/LCCC packaging was halved by the application of novel packaging materials, without changing the cooling mechanisms and the power.

  6. Surface interactions with electromagnetic spectrum relevant to solar thermal propulsion

    Science.gov (United States)

    Bonometti, Joseph Alexander John

    1997-11-01

    Elements of solar thermal rocket propulsion systems were experimentally examined to quantify the most significant physical parameters related to concentrating and capturing solar energy. A detailed examination of the sun's electromagnetic flux impingement upon a solar concentrator, redirection to a secondary reflector or refractor optic and absorption in an opaque cavity surface are presented. Research performed includes the analysis and design of a unique high temperature solar laboratory at the University of Alabama in Huntsville, its construction and subsequent operation. The entire facility was a prerequisite to conducting this experimental research and is the result of an initial two-year research effort. Four primary elements were experimentally examined and their relationship to the solar heating profile analyzed to optimize it for use in a solar thermal upper stage. The first was the comparison of concentrator types to define the incident energy profile with the conclusion that their type or quality was insignificant to the thermal heating profile in an absorber cavity. Rigid, thin-film and Fresnel concentrators were experimentally assessed. The second element was the evaluation of the absorber geometry's length-to-diameter ratio of a cylindrical cavity and included the addition of a secondary optic. The secondary optic was recognized as a requirement in the solar thermal rocket and could either improve the flux distribution on the cavity wall using a refractor with extractor rod, or hinder it as in using a parabolic reflector. The third was direct measurement of absorber material properties at elevated temperatures. Reflectivity, absorptivity and emissivity were determined for rhenium at 1000 Kelvin. The reflectivity measurements included both diffuse and specular reflection components and sample coupons of rhenium and niobium were shown to decrease in reflectivity when heated to temperatures approaching 1200 degrees Kelvin. The methodology was unique in

  7. Thermal imaging of Erta 'Ale active lava lake (Ethiopia)

    Science.gov (United States)

    Spampinato, L.; Oppenheimer, C.; Calvari, S.; Cannata, A.; Montalto, P.

    2009-04-01

    Active lava lakes represent the uppermost portion of a volume of convective magma exposed to the atmosphere, and provide open windows on magma dynamics within shallow reservoirs. Erta ‘Ale volcano located within the Danakil Depression in Ethiopia, hosts one of the few permanent convecting lava lakes, active at least since the last century. We report here the main features of Erta ‘Ale lake surface investigated using a hand-held infrared thermal camera between 11 and 12 November 2006. In both days, the lake surface was mainly characterized by efficient magma circulation reflecting in the formation of well-marked incandescent cracks and wide crust plates. These crossed the lake from the upwelling to the downwelling margin with mean speeds ranging between 0.01 and 0.15 m s-1. Hot spots opened eventually in the middle of crust plates and/or along cracks. These produced explosive activity lasting commonly between ~10 and 200 sec. Apparent temperatures at cracks ranged between ~700 and 1070˚C, and between ~300 and 500˚C at crust plates. Radiant power output of the lake varied between ~45 and 76 MW according to the superficial activity and continuous resurfacing of the lake. Time series analysis of the radiant power output data reveals cyclicity with a period of ~10 min. The combination of visual and thermal observations with apparent mean temperatures and convection rates allows us to interpret these signals as the periodic release of hot overpressured gas bubbles at the lake surface.

  8. Surface active monomers synthesis, properties, and application

    CERN Document Server

    Borzenkov, Mykola

    2014-01-01

    This brief includes information on the background?of and development of synthesis of various types of surface active monomers. The authors explain the importance of utilization of surface active monomers for creation of surface active polymers? and the various biomedical applications of such compounds . This brief introduces techniques for the synthesis of novel types of surface active monomers, their colloidal and polymerizable properties and application for needs of medicine and biology.

  9. Sensitivity enhancement of surface thermal lens technique with a short-wavelength probe beam: Experiment

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xiaorong [Institute of Optics and Electronics, Chinese Academy of Sciences and Key Laboratory of Optical Engineering, Chinese Academy of Sciences, Chengdu 610209 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Li, Bincheng [Institute of Optics and Electronics, Chinese Academy of Sciences and Key Laboratory of Optical Engineering, Chinese Academy of Sciences, Chengdu 610209 (China)

    2015-02-15

    Surface thermal lens is a highly sensitive photothermal technique to measure low absorption losses of various solid materials. In such applications, the sensitivity of surface thermal lens is a key parameter for measuring extremely low absorption. In this paper, we experimentally investigated the influence of probe beam wavelength on the sensitivity of surface thermal lens for measuring the low absorptance of optical laser components. Three probe lasers with wavelength 375 nm, 633 nm, and 1570 nm were used, respectively, to detect the surface thermal lens amplitude of a highly reflective coating sample excited by a cw modulated Gaussian beam at 1064 nm. The experimental results showed that the maximum amplitude of surface thermal lens signal obtained at corresponding optimized detection distance was inversely proportional to the wavelength of the probe beam, as predicted by previous theoretical model. The sensitivity of surface thermal lens could, therefore, be improved by detecting surface thermal lens signal with a short-wavelength probe beam.

  10. Behavior of phenol adsorption on thermal modified activated carbon☆

    Institute of Scientific and Technical Information of China (English)

    Dengfeng Zhang; Peili Huo; Wei Liu

    2016-01-01

    Adsorption process is acknowledged as an effective option for phenolic wastewater treatment. In this work, the activated carbon (AC) samples after thermal modification were prepared by using muffle furnace. The phenol ad-sorption kinetics and equilibrium measurements were carried out under static conditions at temperature ranging from 25 to 55 °C. The test results show that the thermal modification can enhance phenol adsorption on AC samples. The porous structure and surface chemistry analyses indicate that the decay in pore morphology and decrease of total oxygen-containing functional groups are found for the thermal modified AC samples. Thus, it can be further inferred that the decrease of total oxygen-containing functional groups on the modified AC sam-ples is the main reason for the enhanced phenol adsorption capacity. For both the raw sample and the optimum modified AC sample at 900 °C, the pseudo-second order kinetics and Langmuir models are found to fit the exper-imental data very well. The maximum phenol adsorption capacity of the optimum modified AC sample can reach 144.93 mg·g−1 which is higher than that of the raw sample, i.e. 119.53 mg·g−1. Adsorption thermodynamics analysis confirms that the phenol adsorption on the optimum modified AC sample is an exothermic process and mainly via physical adsorption.

  11. Thermal control of sequential on-surface transformation of a hydrocarbon molecule on a copper surface

    Science.gov (United States)

    Kawai, Shigeki; Haapasilta, Ville; Lindner, Benjamin D.; Tahara, Kazukuni; Spijker, Peter; Buitendijk, Jeroen A.; Pawlak, Rémy; Meier, Tobias; Tobe, Yoshito; Foster, Adam S.; Meyer, Ernst

    2016-09-01

    On-surface chemical reactions hold the potential for manufacturing nanoscale structures directly onto surfaces by linking carbon atoms in a single-step reaction. To fabricate more complex and functionalized structures, the control of the on-surface chemical reactions must be developed significantly. Here, we present a thermally controlled sequential three-step chemical transformation of a hydrocarbon molecule on a Cu(111) surface. With a combination of high-resolution atomic force microscopy and first-principles computations, we investigate the transformation process in step-by-step detail from the initial structure to the final product via two intermediate states. The results demonstrate that surfaces can be used as catalysing templates to obtain compounds, which cannot easily be synthesized by solution chemistry.

  12. Wettability Control of Gold Surfaces Modified with Benzenethiol Derivatives: Water Contact Angle and Thermal Stability.

    Science.gov (United States)

    Tatara, Shingo; Kuzumoto, Yasutaka; Kitamura, Masatoshi

    2016-04-01

    The water wettability of Au surfaces has been controlled using various benzenethiol derivatives including 4-methylbenzenethiol, pentafluorobenzenethiol, 4-flubrobenzenethiol, 4-methoxy-benzenethiol, 4-nitrobenzenethiol, and 4-hydroxybenzenethiol. The water contact angle of the Au surface modified with the benzenethiol derivative was found to vary in the wide range of 30.9° to 88.3°. The contact angle of the modified Au films annealed was also measured in order to investigate their thermal stability. The change in the contact angle indicated that the modified surface is stable at temperatures below about 400 K. Meanwhile, the activation energy of desorption from the modified surface was estimated from the change in the contact angle. The modified Au surface was also examined using X-ray photoelectron spectroscopy.

  13. Quantitative reconstruction of thermal and dynamic characteristics of lava flow from surface thermal measurements

    Science.gov (United States)

    Korotkii, Alexander; Kovtunov, Dmitry; Ismail-Zadeh, Alik; Tsepelev, Igor; Melnik, Oleg

    2016-06-01

    We study a model of lava flow to determine its thermal and dynamic characteristics from thermal measurements of the lava at its surface. Mathematically this problem is reduced to solving an inverse boundary problem. Namely, using known conditions at one part of the model boundary we determine the missing condition at the remaining part of the boundary. We develop a numerical approach to the mathematical problem in the case of steady-state flow. Assuming that the temperature and the heat flow are prescribed at the upper surface of the model domain, we determine the flow characteristics in the entire model domain using a variational (adjoint) method. We have performed computations of model examples and showed that in the case of smooth input data the lava temperature and the flow velocity can be reconstructed with a high accuracy. As expected, a noise imposed on the smooth input data results in a less accurate solution, but still acceptable below some noise level. Also we analyse the influence of optimization methods on the solution convergence rate. The proposed method for reconstruction of physical parameters of lava flows can also be applied to other problems in geophysical fluid flows.

  14. Evaluation of thermal resistance of building insulations with reflective surfaces

    Science.gov (United States)

    Št'astník, S.

    2012-09-01

    The thermal resistance of advanced insulation materials, applied namely in civil engineering, containing reflective surfaces and air gaps, cannot be evaluated correctly using the valid European standards because of presence of the dominant nonlinear radiative heat transfer and other phenomena not included in the recommended computational formulae. The proper general physical analysis refers to rather complicated problems from classical thermodynamics, whose both existence theory and numerical analysis contain open questions and cannot be done in practice when the optimization of composition of insulation layers is required. This paper, coming from original experimental results, demonstrates an alternative simplified computational approach, taking into account the most important physical processes, useful in the design of modern insulation systems.

  15. Thermal analysis of activated carbons modified with silver metavanadate

    Energy Technology Data Exchange (ETDEWEB)

    Goscianska, Joanna; Nowicki, Piotr; Nowak, Izabela [Faculty of Chemistry, Adam Mickiewicz University in Poznan, Grunwaldzka 6, 60-780 Poznan (Poland); Pietrzak, Robert, E-mail: pietrob@amu.edu.pl [Faculty of Chemistry, Adam Mickiewicz University in Poznan, Grunwaldzka 6, 60-780 Poznan (Poland)

    2012-08-10

    Highlights: Black-Right-Pointing-Pointer Preparation of the activated carbons from waste materials as new supports for AgVO{sub 3}. Black-Right-Pointing-Pointer Decomposition of AgVO{sub 3} to V{sub 2}O{sub 5} and Ag{sup 0} for the samples 1 and 3 wt.% Ag-V is observed. Black-Right-Pointing-Pointer Samples containing 5 wt.% Ag-V decompose to vanadyl species as intermediate compounds. - Abstract: The effect of silver metavanadate doping on physicochemical properties and thermal behaviour of the activated carbons obtained from waste materials was investigated. The carbonaceous supports were subjected to carbonisation at 400 or 600 Degree-Sign C. The samples carbonised at 600 Degree-Sign C have much more developed surface area and porous structure than the analogous samples obtained at 400 Degree-Sign C. Impregnation of activated carbons with silver metavanadate leads to a decrease in their surface area and pore volume. According to thermal analysis (TG, DTG) in the samples containing 1 and 3 wt.% of silver metavanadate, AgVO{sub 3} is fully decomposed to do vanadium oxide and Ag, with no intermediate products, while in the samples containing 5 wt.% AgVO{sub 3}, this salt is decomposed to vanadyl species as intermediate compounds at 350 Degree-Sign C before the formation of V{sub 2}O{sub 5} at 500 Degree-Sign C. Moreover, in all samples impregnated with silver metavanadate the nanoparticles of silver undergo crystallisation leading to reduction of Ag{sup +} ions from the vanadium salt to Ag{sup 0}.

  16. Porous Materials from Thermally Activated Kaolinite: Preparation, Characterization and Application

    Directory of Open Access Journals (Sweden)

    Jun Luo

    2017-06-01

    Full Text Available In the present study, porous alumina/silica materials were prepared by selective leaching of silicon/aluminum constituents from thermal-activated kaolinite in inorganic acid or alkali liquor. The correlations between the characteristics of the prepared porous materials and the dissolution properties of activated kaolinite were also investigated. The results show that the specific surface area (SSA of porous alumina/silica increases with silica/alumina dissolution, but without marked change of the BJH pore size. Furthermore, change in pore volume is more dependent on activation temperature. The porous alumina and silica obtained from alkali leaching of kaolinite activated at 1150 °C for 15 min and acid leaching of kaolinite activated at 850 °C for 15 min are mesoporous, with SSAs, BJH pore sizes and pore volumes of 55.8 m2/g and 280.3 m2/g, 6.06 nm and 3.06 nm, 0.1455 mL/g and 0.1945 mL/g, respectively. According to the adsorption tests, porous alumina has superior adsorption capacities for Cu2+, Pb2+ and Cd2+ compared with porous silica and activated carbon. The maximum capacities of porous alumina for Cu2+, Pb2+ and Cd2+ are 134 mg/g, 183 mg/g and 195 mg/g, respectively, at 30 °C.

  17. Lava lake surface characterization by thermal imaging: Erta 'Ale volcano (Ethiopia)

    Science.gov (United States)

    Spampinato, L.; Oppenheimer, C.; Calvari, S.; Cannata, A.; Montalto, P.

    2008-12-01

    Active lava lakes represent the exposed, uppermost part of convecting magma systems and provide windows into the dynamics of magma transport and degassing. Erta 'Ale volcano located within the Danakil Depression in Ethiopia hosts one of the few permanent convecting lava lakes, probably active for a century or more. We report here on the main features of the lava lake surface based on observations from an infrared thermal camera made on 11 November 2006. Efficient magma circulation was reflected in the sustained transport of the surface, which was composed of pronounced incandescent cracks that separated wide plates of cooler crust. These crossed the lake from the upwelling to the downwelling margin with mean speeds ranging between 0.01 and 0.15 m s-1. Hot spots eventually opened in the middle of crust plates and/or along cracks. These produced mild explosive activity lasting commonly between ˜10 and ˜200 s. Apparent temperatures of cracks ranged between ˜700 and 1070°C, and of crust between ˜300 and 500°C. Radiant power output of the lake varied between ˜45 and 76 MW according to the superficial activity and continuous resurfacing of the lake. Time series analysis of the radiant power output data reveals cyclicity with a period of ˜10 min. The combination of visual and thermal observations with apparent mean temperatures and convection rates allows us to interpret these signals as the periodic release of hot overpressured gas bubbles at the lake surface.

  18. Thermally tailored gradient topography surface on elastomeric thin films.

    Science.gov (United States)

    Roy, Sudeshna; Bhandaru, Nandini; Das, Ritopa; Harikrishnan, G; Mukherjee, Rabibrata

    2014-05-14

    We report a simple method for creating a nanopatterned surface with continuous variation in feature height on an elastomeric thin film. The technique is based on imprinting the surface of a film of thermo-curable elastomer (Sylgard 184), which has continuous variation in cross-linking density introduced by means of differential heating. This results in variation of viscoelasticity across the length of the surface and the film exhibits differential partial relaxation after imprinting with a flexible stamp and subjecting it to an externally applied stress for a transient duration. An intrinsic perfect negative replica of the stamp pattern is initially created over the entire film surface as long as the external force remains active. After the external force is withdrawn, there is partial relaxation of the applied stresses, which is manifested as reduction in amplitude of the imprinted features. Due to the spatial viscoelasticity gradient, the extent of stress relaxation induced feature height reduction varies across the length of the film (L), resulting in a surface with a gradient topography with progressively varying feature heights (hF). The steepness of the gradient can be controlled by varying the temperature gradient as well as the duration of precuring of the film prior to imprinting. The method has also been utilized for fabricating wettability gradient surfaces using a high aspect ratio biomimetic stamp. The use of a flexible stamp allows the technique to be extended for creating a gradient topography on nonplanar surfaces as well. We also show that the gradient surfaces with regular structures can be used in combinatorial studies related to pattern directed dewetting.

  19. Improvements to a Response Surface Thermal Model for Orion

    Science.gov (United States)

    Miller, Stephen W.; Walker, William Q.

    2011-01-01

    A study was performed to determine if a Design of Experiments (DOE)/Response Surface Methodology could be applied to on-orbit thermal analysis and produce a set of Response Surface Equations (RSE) that predict Orion vehicle temperatures within 10 F. The study used the Orion Outer Mold Line model. Five separate factors were identified for study: yaw, pitch, roll, beta angle, and the environmental parameters. Twenty-three external Orion components were selected and their minimum and maximum temperatures captured over a period of two orbits. Thus, there are 46 responses. A DOE case matrix of 145 runs was developed. The data from these cases were analyzed to produce a fifth order RSE for each of the temperature responses. For the 145 cases in the DOE matrix, the agreement between the engineering data and the RSE predictions was encouraging with 40 of the 46 RSEs predicting temperatures within the goal band. However, the verification cases showed most responses did not meet the 10 F goal. After reframing the focus of the study to better align the RSE development with the purposes of the model, a set of RSEs for both the minimum and maximum radiator temperatures was produced which predicted the engineering model output within +/-4 F. Therefore, with the correct application of the DOE/RSE methodology, RSEs can be developed that provide analysts a fast and easy way to screen large numbers of environments and assess proposed changes to the RSE factors.

  20. Attenuating the surface Urban Heat Island within the Local Thermal Zones through land surface modification.

    Science.gov (United States)

    Wang, Jiong; Ouyang, Wanlu

    2017-02-01

    Inefficient mitigation of excessive heat is attributed to the discrepancy between the scope of climate research and conventional planning practice. This study approaches this problem at both domains. Generally, the study, on one hand, claims that the climate research of the temperature phenomenon should be at local scale, where implementation of planning and design strategies can be more feasible. On the other hand, the study suggests that the land surface factors should be organized into zones or patches, which conforms to the urban planning and design manner. Thus in each zone, the land surface composition of those excessively hot places can be compared to the zonal standard. The comparison gives guidance to the modification of the land surface factors at the target places. Specifically, this study concerns the Land Surface Temperature (LST) in Wuhan, China. The land surface is classified into Local Thermal Zones (LTZ). The specifications of temperature sensitive land surface factors are relative homogeneous in each zone and so is the variation of the LST. By extending the city scale analysis of Urban Heat Island into local scale, the Local Surface Urban Heat Islands (LSUHIs) are extracted. Those places in each zone that constantly maintain as LSUHI and exceed the homogenous LST variation are considered as target places or hotspots with higher mitigation or adaptation priority. The operation is equivalent to attenuate the abnormal LST variation in each zone. The framework is practical in the form of prioritization and zoning, and mitigation strategies are essentially operated locally.

  1. Thermal expansion compensator having an elastic conductive element bonded to two facing surfaces

    Science.gov (United States)

    Determan, William (Inventor); Matejczyk, Daniel Edward (Inventor)

    2012-01-01

    A thermal expansion compensator is provided and includes a first electrode structure having a first surface, a second electrode structure having a second surface facing the first surface and an elastic element bonded to the first and second surfaces and including a conductive element by which the first and second electrode structures electrically and/or thermally communicate, the conductive element having a length that is not substantially longer than a distance between the first and second surfaces.

  2. Casimir-Polder forces in the presence of thermally excited surface modes

    CERN Document Server

    Laliotis, Athanasios; Maurin, Isabelle; Ducloy, Martial; Bloch, Daniel

    2014-01-01

    The temperature dependence of the Casimir-Polder interaction addresses fundamental issues for understanding vacuum and thermal fluctuations. It is highly sensitive to surface waves which, in the near field, govern the thermal emission of a hot surface. Here we use optical reflection spectroscopy to monitor the atom-surface interaction between a Cs*(7D3/2) atom and a hot sapphire surface at a distance ~ 100 nm. In our experiments, that explore a large range of temperatures (500-1000K) the hot surface is at thermal equilibrium with the vacuum. The observed increase of the interaction with temperature, by up to 50 %, relies on the coupling between atomic virtual transitions in the infrared range and thermally excited surface-polariton modes. We extrapolate our findings to a broad distance range, from the isolated free atom to the short distances relevant to physical chemistry. Our work also opens the prospect of controlling atom surface interactions by engineering thermal fields.

  3. Feasibility of culvert IED detection using thermal neutron activation

    Science.gov (United States)

    Faust, Anthony A.; McFee, John E.; Clifford, Edward T. H.; Andrews, Hugh Robert; Mosquera, Cristian; Roberts, William C.

    2012-06-01

    Bulk explosives hidden in culverts pose a serious threat to the Canadian and allied armies. Culverts provide an opportunity to conceal insurgent activity, avoid the need for detectable surface disturbances, and limit the applicability of conventional sub-surface sensing techniques. Further, in spite of the large masses of explosives that can be employed, the large sensor{target separation makes detection of the bulk explosive content challeng- ing. Defence R&D Canada { Sueld and Bubble Technology Industries have been developing thermal neutron activation (TNA) sensors for detection of buried bulk explosives for over 15 years. The next generation TNA sensor, known as TNA2, incorporates a number of improvements that allow for increased sensor-to-target dis- tances, making it potentially feasible to detect large improvised explosive devices (IEDs) in culverts using TNA. Experiments to determine the ability of TNA2 to detect improvised explosive devices in culverts are described, and the resulting signal levels observed for relevant quantities of explosives are presented. Observations conrm that bulk explosives detection using TNA against a culvert-IED is possible, with large charges posing a detection challenge at least as dicult as that of a deeply buried anti-tank landmine. Because of the prototype nature of the TNA sensor used, it is not yet possible to make denitive statements about the absolute sensitivity or detection time. Further investigation is warranted.

  4. Dislocation Pile-Ups, Material Strength Levels, and Thermal Activation

    Science.gov (United States)

    Armstrong, Ronald W.

    2016-12-01

    A review dedicated to James C.M. Li is given of dislocation pile-ups and their connection to the Hall-Petch dependence of polycrystalline strength and fracture mechanics properties on an inverse square root of grain size basis, with such grain size dependence now very importantly extended to nanopolycrystalline material behaviors. An analogous H-P dependence is described for the inverse activation volume parameter obtained from the strain rate (and thermal) dependencies contained in the model dislocation thermal activation-strain rate analysis, also relating to pioneering contributions of Li to the topic of thermally activated dislocation dynamics.

  5. Thermal anomaly at the Earth's surface associated with a lava tube

    Science.gov (United States)

    Piombo, Antonello; Di Bari, Marco; Tallarico, Andrea; Dragoni, Michele

    2016-10-01

    Lava tubes are frequently encountered in volcanic areas. The formation of lava tubes has strong implications on the volcanic hazard during effusive eruptions. The thermal dissipation of lava flowing in a tube is reduced in respect to the lava flowing in an open channel so the lava may threaten areas that would not be reached by flows in open channels: for this reason it is important to detect the presence of lava tubes. In this work we propose a model to detect the presence and the characteristics of lava tubes by their thermal footprint at the surface. We model numerically the temperature distribution and the heat flow, both in the steady and the transient state, and we take into account the principal thermal effects due to the presence of an active lava tube, i.e. the conduction to the ground and the atmosphere, the convection and the radiation in the atmosphere. We assume that lava fluid is at high temperature, in motion inside a sloping tube under the gravity force. The thermal profile across the tube direction, in particular the width of the temperature curve, allows to evaluate the depth of the tube. The values of maximum temperature and of tube depth allow to estimate the area of the tube section. The shape of the temperature curve and its asymmetry can give information about the geometry of the tube. If we observe volcanic areas at different times by thermal cameras, we can detect anomalies and evaluate their causes during an eruption; in particular, we can evaluate whether they are due to active lava flows or not and what is their state. For lava tubes, we can connect thermal anomalies with lava tube position, characteristics and state.

  6. YAG laser welding with surface activating flux

    Institute of Scientific and Technical Information of China (English)

    樊丁; 张瑞华; 田中学; 中田一博; 牛尾诚夫

    2003-01-01

    YAG laser welding with surface activating flux has been investigated, and the influencing factors and mechanism are discussed. The results show that both surface activating flux and surface active element S have fantastic effects on the YAG laser weld shape, that is to obviously increase the weld penetration and D/W ratio in various welding conditions. The mechanism is thought to be the change of weld pool surface tension temperature coefficient, thus, the change of fluid flow pattern in weld pool due to the flux.

  7. Practical Calculation of Thermal Deformation and Manufacture Error uin Surface Grinding

    Institute of Scientific and Technical Information of China (English)

    周里群; 李玉平

    2002-01-01

    The paper submits a method to calculate thermal deformation and manufacture error in surface grinding.The author established a simplified temperature field model.and derived the thermal deformaiton of the ground workpiece,It is found that there exists not only a upwarp thermal deformation,but also a parallel expansion thermal deformation.A upwarp thermal deformation causes a concave shape error on the profile of the workpiece,and a parallel expansion thermal deformation causes a dimension error in height.The calculations of examples are given and compared with presented experiment data.

  8. Thermal neutrons' flux near the Earth's surface as an evidence of the crustal stress

    Science.gov (United States)

    Sigaeva, Ekaterina; Nechayev, Oleg; Volodichev, Nikolay; Antonova, Valentina; Kryukov, Sergey; Chubenko, Alexander; Shchepetov, Alexander

    There are some ideas about the Earth’s global seismic activity appearance due to tidal forces. At the same time, the correlations between the big series of the earthquakes and the New and Full Moons and between the New and Full Moons and the increasings of the thermal neutrons’ flux from the Earth’s crust were observed. It is as though there are internal links between these three natural phenomena and the physical reasons for their appearance are the same. The paper presents the results of the ground-based thermal neutrons observations during different time periods characterized with phenomena in the near-Earth space (for instance, the New and Full Moon). Basing on the up-to-date conception of the tidal waves influence on the Earth's crust the authors confirm the role of the Moon in the production of the neutron flux near the Earth's surface.

  9. Thermally activated, single component epoxy systems

    KAUST Repository

    Unruh, David A.

    2011-08-23

    A single component epoxy system in which the resin and hardener components found in many two-component epoxies are combined onto the same molecule is described. The single molecule precursor to the epoxy resin contains both multiple epoxide moieties and a diamine held latent by thermally degradable carbamate linkages. These bis-carbamate "single molecule epoxies" have an essentially infinite shelf life and access a significant range in curing temperatures related to the structure of the carbamate linkages used. © 2011 American Chemical Society.

  10. Directional Characteristics of Thermal-Infrared Beaming from Atmosphereless Planetary Surfaces - A New Thermophysical Model

    CERN Document Server

    Rozitis, Ben

    2012-01-01

    We present a new rough-surface thermophysical model (Advanced Thermophysical Model or ATPM) that describes the observed directional thermal emission from any atmosphereless planetary surface. It explicitly incorporates partial shadowing, scattering of sunlight, selfheating and thermal-infrared beaming (re-radiation of absorbed sunlight back towards the Sun as a result of surface roughness). The model is verified by accurately reproducing ground-based directional thermal emission measurements of the lunar surface using surface properties that are consistent with the findings of the Apollo missions and roughness characterised by an RMS slope of ~32 degrees. By considering the wide range of potential asteroid surface properties, the model implies a beaming effect that cannot be described by a simple parameter or function. It is highly dependent on the illumination and viewing angles as well as surface thermal properties and is predominantly caused by macroscopic rather than microscopic roughness. Roughness alter...

  11. Thermally activated conductance of a silicon inversion layer by electrons excited above the mobility edge

    NARCIS (Netherlands)

    Niederer, H.H.J.M.; Mattey, A.P.M.; Sparnaay, M.J.

    1981-01-01

    The thermally activated conductivity sigma of an n-type inversion layer on a (100) oriented silicon surface and its derivative d sigma /dT were measured in the temperature range 1.4K-4.2K. Above T approximately=2.5K both the temperature dependence of (T/ sigma ) (d sigma /dT) and the relation betwee

  12. Thermal Technology Development Activities at the Goddard Space Flight Center: 2001

    Science.gov (United States)

    Butler, Dan; Powers, Edward I. (Technical Monitor)

    2001-01-01

    Activities include the development of two phase systems which are composed of 1) heat pipes and variable conductance heat pipes, 2)capillary pumped loops, 3) loop heat pipes, 4) vapor compression systems (heat pumps), 5) phase change materials. Also in the development phase are variable emittance surfaces, advanced coatings, high conductivity materials, and electrohydrodynamic (EHD) thermal control systems.

  13. Advanced deposition model for thermal activated chemical vapor deposition

    Science.gov (United States)

    Cai, Dang

    Thermal Activated Chemical Vapor Deposition (TACVD) is defined as the formation of a stable solid product on a heated substrate surface from chemical reactions and/or dissociation of gaseous reactants in an activated environment. It has become an essential process for producing solid film, bulk material, coating, fibers, powders and monolithic components. Global market of CVD products has reached multi billions dollars for each year. In the recent years CVD process has been extensively used to manufacture semiconductors and other electronic components such as polysilicon, AlN and GaN. Extensive research effort has been directed to improve deposition quality and throughput. To obtain fast and high quality deposition, operational conditions such as temperature, pressure, fluid velocity and species concentration and geometry conditions such as source-substrate distance need to be well controlled in a CVD system. This thesis will focus on design of CVD processes through understanding the transport and reaction phenomena in the growth reactor. Since the in situ monitor is almost impossible for CVD reactor, many industrial resources have been expended to determine the optimum design by semi-empirical methods and trial-and-error procedures. This approach has allowed the achievement of improvements in the deposition sequence, but begins to show its limitations, as this method cannot always fulfill the more and more stringent specifications of the industry. To resolve this problem, numerical simulation is widely used in studying the growth techniques. The difficulty of numerical simulation of TACVD crystal growth process lies in the simulation of gas phase and surface reactions, especially the latter one, due to the fact that very limited kinetic information is available in the open literature. In this thesis, an advanced deposition model was developed to study the multi-component fluid flow, homogeneous gas phase reactions inside the reactor chamber, heterogeneous surface

  14. Comparison of Observed Surface Temperatures of 4 Vesta to the KRC Thermal Model

    Science.gov (United States)

    Titus, T. N.; Becker, K. J.; Anderson, J. A.; Capria, M. T.; Tosi, F.; DeSanctis, M. C.; Palomba, E.; Grassi, D.; Capaccioni, F.; Ammannito, E.; Combe, J.-P.; McCord, T. B.; Li, J.-Y.; Russell, C. T.; Ryamond, C. A.; Mittlefehldt, D.; Toplis, M.; Forni, O.; Sykes, M. V.

    2012-01-01

    In this work, we will compare ob-served temperatures of the surface of Vesta using data acquired by the Dawn [1] Visible and Infrared Map-ping Spectrometer (VIR-MS) [2] during the approach phase to model results from the KRC thermal model. High thermal inertia materials, such as bedrock, resist changes in temperature while temperatures of low thermal inertia material, such as dust, respond quickly to changes in solar insolation. The surface of Vesta is expected to have low to medium thermal inertia values, with the most commonly used value being extremely low at 15 TIU [4]. There are several parameters which affect observed temperatures in addition to thermal inertia: bond albedo, slope, and surface roughness. In addition to these parameters, real surfaces are rarely uniform monoliths that can be described by a single thermal inertia value. Real surfaces are often vertically layered or are mixtures of dust and rock. For Vesta's surface, with temperature extremes ranging from 50 K to 275 K and no atmosphere, even a uniform monolithic surface may have non-uniform thermal inertia due to temperature dependent thermal conductivity.

  15. Implementation of Active Thermal Control (ATC) for the Soil Moisture Active and Passive (SMAP) Radiometer

    Science.gov (United States)

    Mikhaylov, Rebecca; Kwack, Eug; French, Richard; Dawson, Douglas; Hoffman, Pamela

    2014-01-01

    NASA's Earth Observing Soil Moisture Active and Passive (SMAP) Mission is scheduled to launch in November 2014 into a 685 kilometer near-polar, sun-synchronous orbit. SMAP will provide comprehensive global mapping measurements of soil moisture and freeze/thaw state in order to enhance understanding of the processes that link the water, energy, and carbon cycles. The primary objectives of SMAP are to improve worldwide weather and flood forecasting, enhance climate prediction, and refine drought and agriculture monitoring during its three year mission. The SMAP instrument architecture incorporates an L-band radar and an L-band radiometer which share a common feed horn and parabolic mesh reflector. The instrument rotates about the nadir axis at approximately 15 revolutions per minute, thereby providing a conically scanning wide swath antenna beam that is capable of achieving global coverage within three days. In order to make the necessary precise surface emission measurements from space, the electronics and hardware associated with the radiometer must meet tight short-term (instantaneous and orbital) and long-term (monthly and mission) thermal stabilities. Maintaining these tight thermal stabilities is quite challenging because the sensitive electronics are located on a fast spinning platform that can either be in full sunlight or total eclipse, thus exposing them to a highly transient environment. A passive design approach was first adopted early in the design cycle as a low-cost solution. With careful thermal design efforts to cocoon and protect all sensitive components, all stability requirements were met passively. Active thermal control (ATC) was later added after the instrument Preliminary Design Review (PDR) to mitigate the threat of undetected gain glitches, not for thermal-stability reasons. Gain glitches are common problems with radiometers during missions, and one simple way to avoid gain glitches is to use the in-flight set point programmability that ATC

  16. Solar Thermal Propulsion Investigation Activities in NAL

    Science.gov (United States)

    Sahara, Hironori; Shimizu, Morio

    2004-03-01

    We successfully developed the ultra-light single shell paraboloidal concentrators made of a sheet of aluminized or silvered polymer membrane, formed via plastic deformation due to stress relaxation under high temperature condition by means of Straight Formation Method. Furthermore, we improved the precision of the concentrators by taking the elastic deformation of residual stress into consideration, and obtained the best concentration performance equivalent to a highly precise paraboloidal glass mirror. In solar concentration, the diameter of solar focal image via the single shell polymer concentrator is almost equal to that via the glass mirror and they are twice as large as that of the theoretical. The ultra-light single shell polymer concentrators are very useful for the concentrator in solar thermal propulsion system and solar power station in particular, and also promising item for beamed energy propulsion.

  17. Active thermal figure control for the TOPS II primary mirror

    Science.gov (United States)

    Angel, Roger; Kang, Tae; Cuerden, Brian; Guyon, Olivier; Stahl, Phil

    2007-09-01

    TOPS (Telescope to Observe Planetary Systems) is the first coronagraphic telescope concept designed specifically to take advantage of Guyon's method of Phase Induced Amplitude Apodization PIAA).1 The TOPS primary mirror may incorporates active figure control to help achieve the desired wavefront control to approximately 1 angstrom RMS accurate across the spectral bandwidth. Direct correction of the primary figure avoids the need for a separate small deformable mirror. Because of Fresnel propagation, correction at a separate surface can introduce serious chromatic errors unless it is precisely conjugated to the primary. Active primary control also reduces complexity and mass and increases system throughput, and will likely enable a full system test to the 10-10 level in the 1 g environment before launch. We plan to use thermal actuators with no mechanical disturbance, using radiative heating or cooling fingers distributed inside the cells of a honeycomb mirror. The glass would have very small but finite coefficient of expansion of ~ 5x10 -8/C. Low order modes would be controlled by front-to-back gradients and high order modes by local rib expansion and contraction. Finite element models indicate that for a mirror with n cells up to n Zernike modes can be corrected to better than 90% fidelity, with still higher accuracy for the lower modes. An initial demonstration has been made with a borosilicate honeycomb mirror. Interferometric measurements show a single cell influence function with 300 nm stroke and ~5 minute time constant.

  18. Tuning thermal transport in ultrathin silicon membranes by surface nanoscale engineering.

    Science.gov (United States)

    Neogi, Sanghamitra; Reparaz, J Sebastian; Pereira, Luiz Felipe C; Graczykowski, Bartlomiej; Wagner, Markus R; Sledzinska, Marianna; Shchepetov, Andrey; Prunnila, Mika; Ahopelto, Jouni; Sotomayor-Torres, Clivia M; Donadio, Davide

    2015-04-28

    A detailed understanding of the connections of fabrication and processing to structural and thermal properties of low-dimensional nanostructures is essential to design materials and devices for phononics, nanoscale thermal management, and thermoelectric applications. Silicon provides an ideal platform to study the relations between structure and heat transport since its thermal conductivity can be tuned over 2 orders of magnitude by nanostructuring. Combining realistic atomistic modeling and experiments, we unravel the origin of the thermal conductivity reduction in ultrathin suspended silicon membranes, down to a thickness of 4 nm. Heat transport is mostly controlled by surface scattering: rough layers of native oxide at surfaces limit the mean free path of thermal phonons below 100 nm. Removing the oxide layers by chemical processing allows us to tune the thermal conductivity over 1 order of magnitude. Our results guide materials design for future phononic applications, setting the length scale at which nanostructuring affects thermal phonons most effectively.

  19. Nanoporosity development in the thermal-shock KOH activation of brown coal

    Energy Technology Data Exchange (ETDEWEB)

    Kucherenko, V.A.; Shendrik, T.G.; Tamarkina, Y.V.; Mysyk, R.D. [LM Litvinenko Institute of Physical Organic & Coal Chemistry, Donetsk (Ukraine)

    2010-12-15

    Thermal-shock KOH activation of brown coal (800 degrees C, KOH/coal ratio 1 g/g) was shown to produce nanoporous activated carbon with more developed surface area than thermally-programmed heating (S-BET up to 1700 vs 1000 m{sup 2}/g). Increasing the KOH/coal ratio (up to 1 g/g) in the activated mixture increases the total pore volume (0.14-1.0 cm{sup 3}/g), the micropore volume (0.03-0.71 cm{sup 3}/g), and also the volume of subnanometer pores (0.01-0.40 cm{sup 3}/g). Thermal shock produces nanoporosity at lower KOH/coal ratios (0.5-1.0 g/g) than respective low-rate heating KOH activation.

  20. Immobilization of Active Bacteriophages on Polyhydroxyalkanoate Surfaces.

    Science.gov (United States)

    Wang, Chanchan; Sauvageau, Dominic; Elias, Anastasia

    2016-01-20

    A rapid, efficient technique for the attachment of bacteriophages (phages) onto polyhydroxyalkanoate (PHA) surfaces has been developed and compared to three reported methods for phage immobilization. Polymer surfaces were modified to facilitate phage attachment using (1) plasma treatment alone, (2) plasma treatment followed by activation by 1-ethyl-3-(3-(dimethylamino)propyl)carbodiimide hydrochloride (EDC) and N-hydroxysulfosuccinimide (sulfo-NHS), (3) plasma-initiated acrylic acid grafting, or (4) plasma-initiated acrylic acid grafting with activation by EDC and sulfo-NHS. The impact of each method on the surface chemistry of PHA was investigated using contact angle analysis and X-ray photoelectron spectroscopy. Each of the four treatments was shown to result in both increased hydrophilicity and in the modification of the surface functional groups. Modified surfaces were immersed in suspensions of phage T4 for immobilization. The highest level of phage binding was observed for the surfaces modified by plasma treatment alone. The change in chemical bond states observed for surfaces that underwent plasma treatment is suspected to be the cause of the increased binding of active phages. Plasma-treated surfaces were further analyzed through phage-staining and fluorescence microscopy to assess the surface density of immobilized phages and their capacity to capture hosts. The infective capability of attached phages was confirmed by exposing the phage-immobilized surfaces to the host bacteria Escherichia coli in both plaque and infection dynamic assays. Plasma-treated surfaces with immobilized phages displayed higher infectivity than surfaces treated with other methods; in fact, the equivalent initial multiplicity of infection was 2 orders of magnitude greater than with other methods. Control samples - prepared by immersing polymer surfaces in phage suspensions (without prior plasma treatment) - did not show any bacterial growth inhibition, suggesting they did not bind

  1. Kertész line of thermally activated breakdown phenomena

    KAUST Repository

    Yoshioka, Naoki

    2010-11-12

    Based on a fiber bundle model we substantially extend the phase-transition analogy of thermally activated breakdown of homogeneous materials. We show that the competition of breaking due to stress enhancement and due to thermal fluctuations leads to an astonishing complexity of the phase space of the system: varying the load and the temperature a phase boundary emerges, separating a Griffith-type regime of abrupt failure analogous to first-order phase transitions from disorder dominated fracture where a spanning cluster of cracks emerges. We demonstrate that the phase boundary is the Kertész line of the system along which thermally activated fracture appears as a continuous phase transition analogous to percolation. The Kertész line has technological relevance setting the boundary of safe operation for construction components under high thermal loads. © 2010 The American Physical Society.

  2. Modeling thermally active building components using space mapping

    DEFF Research Database (Denmark)

    Pedersen, Frank; Weitzmann, Peter; Svendsen, Svend

    2005-01-01

    simplified models of the components do not always provide useful solutions, since they are not always able to reproduce the correct thermal behavior. The space mapping technique transforms a simplified, but computationally inexpensive model, in order to align it with a detailed model or measurements....... This paper describes the principle of the space mapping technique, and introduces a simple space mapping technique. The technique is applied to a lumped parameter model of a thermo active component, which provides a model of the thermal performance of the component as a function of two design parameters......In order to efficiently implement thermally active building components in new buildings, it is necessary to evaluate the thermal interaction between them and other building components. Applying parameter investigation or numerical optimization methods to a differential-algebraic (DAE) model...

  3. Understanding the mechanism of surface modification through enhanced thermal and electrochemical stabilities of N-doped graphene oxide

    Energy Technology Data Exchange (ETDEWEB)

    Mehetre, Shantilal S., E-mail: shantilalmehetre@gmail.com; Maktedar, Shrikant S., E-mail: shrikantmaktedar@gmail.com; Singh, Man, E-mail: mansingh50@hotmail.com

    2016-03-15

    Highlights: • The N-doped graphene oxide was confirmed with FTIR, EDS, HR-TEM, SAED, HRXPS, UV, TGA, DSC and CV. • The N-doped graphene oxide was found suitable for thermal and electrochemical applications. • The proposed mechanisms of thermal and electrochemical stabilities were experimentally verified. • The cyclic voltammetry N-doped graphene oxide implies its potential for manifold electrochemical applications. - Abstract: The kinetically active two dimensional surface of graphene oxide (GrO) plays an important role in understanding the chemistry of graphene. The GrO is comprises of carbon and oxygen while the f-(6-AIND) GrO contains nitrogen along with carbon and oxygen. The prominent thermal instability of GrO is widely explored. However, due to the synergistic impact of their constituting elements, the thermal and electrochemical stability of f-(6-AIND) GrO enhances after N-doping with nitrogen containing heterocycles like 6-Aminoindazole. Hence it is essential to probe the mutual impact of various functionalities present over the surface of GrO, to understand the mechanism of direct functionalization of GrO with thermal and electrochemical stabilities. Therefore, the decomposition kinetics of discrete atomic domains and their effect on thermal stability of f-(6-AIND) GrO was revealed with spectroscopic analysis and thermal assessment. Additionally, the mechanism of thermal transformation is precisely developed to demonstrate the impact of heat on weight loss due to the mass transfer. Likewise, the electrochemical properties can be well understood with the help of mechanism of electrochemical activity and cyclic voltammetry experiments. Also, the f-(6-AIND) GrO is confirmed with the help of various surface analysis techniques like FTIR, EDS, HR-XPS, HR-TEM, CV, SAED, TGA, DSC and UV-vis.

  4. Thermal surveillance of active volcanoes. [infrared scanner recordings of thermal anomalies of Mt. Baker volcano

    Science.gov (United States)

    Friedman, J. D. (Principal Investigator)

    1974-01-01

    The author has identified the following significant results. By the end of 1973, aerial infrared scanner traverses for thermal anomaly recordings of all Cascade Range volcanoes were essentially completed. Amplitude level slices of the Mount Baker anomalies were completed and compiled at a scale of 1:24,000, thus producing, for the first time, an accurate map of the distribution and intensity of thermal activity on Mount Baker. The major thermal activity is concentrated within the crater south of the main summit and although it is characterized by intensive solfataric activity and warm ground, it is largely subglacial, causing the development of sizable glacier perforation features. The outgoing radiative flux from the east breach anomalies is sufficient to account for the volume of ice melted to form the glacier perforations. DCP station 6251 has been monitoring a thermally anomalous area on the north slope of Mount Baker. The present thermal activity of Mount Baker accounts for continuing hydrothermal alteration in the crater south of the main summit and recurrent debris avalanches from Sherman Peak on its south rim. The infrared anomalies mapped as part of the experiment SR 251 are considered the basic evidence of the subglacial heating which was the probable triggering mechanism of an avalanche down Boulder Glacier on August 20-21, 1973.

  5. Dynamic characterization for tumor- and deformation-induced thermal contrasts on breast surface: a simulation study

    Science.gov (United States)

    Jiang, Li; Zhan, Wang; Loew, Murray H.

    2009-02-01

    Understanding the complex relationship between the thermal contrasts on the breast surface and the underlying physiological and pathological factors is important for thermogram-based breast cancer detection. Our previous work introduced a combined thermal-elastic modeling method with improved ability to simultaneously characterize both elastic-deformation-induced and tumor-induced thermal contrasts on the breast. In this paper, the technique is further extended to investigate the dynamic behaviors of the breast thermal contrasts during cold stress and thermal recovery procedures in the practice of dynamic thermal imaging. A finite-element method (FEM) has been developed for dynamic thermal and elastic modeling. It is combined with a technique to address the nonlinear elasticity of breast tissues, as would arise in the large deformations caused by gravity. Our simulation results indicate that different sources of the thermal contrasts, such as the presence of a tumor, and elastic deformation, have different transient time courses in dynamic thermal imaging with cold-stress and thermal-recovery. Using appropriate quantifications of the thermal contrasts, we find that the tumor- and deformation-induced thermal contrasts show opposite changes in the initial period of the dynamic courses, whereas the global maxima of the contrast curves are reached at different time points during a cold-stress or thermal-recovery procedure. Moreover, deeper tumors generally lead to smaller peaks but have larger lags in the thermal contrast time course. These findings suggest that dynamic thermal imaging could be useful to differentiate the sources of the thermal contrast on breast surface and hence to enhance tumor detectability.

  6. Mid-infrared thermal imaging for an effective mapping of surface materials and sub-surface detachments in mural paintings: integration of thermography and thermal quasi-reflectography

    Science.gov (United States)

    Daffara, C.; Parisotto, S.; Mariotti, P. I.

    2015-06-01

    Cultural Heritage is discovering how precious is thermal analysis as a tool to improve the restoration, thanks to its ability to inspect hidden details. In this work a novel dual mode imaging approach, based on the integration of thermography and thermal quasi-reflectography (TQR) in the mid-IR is demonstrated for an effective mapping of surface materials and of sub-surface detachments in mural painting. The tool was validated through a unique application: the "Monocromo" by Leonardo da Vinci in Italy. The dual mode acquisition provided two spatially aligned dataset: the TQR image and the thermal sequence. Main steps of the workflow included: 1) TQR analysis to map surface features and 2) to estimate the emissivity; 3) projection of the TQR frame on reference orthophoto and TQR mosaicking; 4) thermography analysis to map detachments; 5) use TQR to solve spatial referencing and mosaicking for the thermal-processed frames. Referencing of thermal images in the visible is a difficult aspect of the thermography technique that the dual mode approach allows to solve in effective way. We finally obtained the TQR and the thermal maps spatially referenced to the mural painting, thus providing the restorer a valuable tool for the restoration of the detachments.

  7. Highly active thermally stable nanoporous gold catalyst

    Science.gov (United States)

    Biener, Juergen; Wittstock, Arne; Biener, Monika M.; Bagge-Hansen, Michael; Baeumer, Marcus; Wichmann, Andre; Neuman, Bjoern

    2016-12-20

    In one embodiment, a system includes a nanoporous gold structure and a plurality of oxide particles deposited on the nanoporous gold structure; the oxide particles are characterized by a crystalline phase. In another embodiment, a method includes depositing oxide nanoparticles on a nanoporous gold support to form an active structure and functionalizing the deposited oxide nanoparticles.

  8. Highly active thermally stable nanoporous gold catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Biener, Juergen; Wittstock, Arne; Biener, Monika M.; Bagge-Hansen, Michael; Baeumer, Marcus; Wichmann, Andre; Neuman, Bjoern

    2016-12-20

    In one embodiment, a system includes a nanoporous gold structure and a plurality of oxide particles deposited on the nanoporous gold structure; the oxide particles are characterized by a crystalline phase. In another embodiment, a method includes depositing oxide nanoparticles on a nanoporous gold support to form an active structure and functionalizing the deposited oxide nanoparticles.

  9. Active Thermal Control Experiments for LISA Ground Verification Testing

    Science.gov (United States)

    Higuchi, Sei; DeBra, Daniel B.

    2006-11-01

    The primary mission goal of LISA is detecting gravitational waves. LISA uses laser metrology to measure the distance between proof masses in three identical spacecrafts. The total acceleration disturbance to each proof mass is required to be below 3 × 10-15 m/s2√Hz . Optical path length variations on each optical bench must be kept below 40 pm/√Hz over 1 Hz to 0.1 mHz. Thermal variations due to, for example, solar radiation or temperature gradients across the proof mass housing will distort the spacecraft causing changes in the mass attraction and sensor location. We have developed a thermal control system developed for the LISA gravitational reference sensor (GRS) ground verification testing which provides thermal stability better than 1 mK/√Hz to f control for the LISA spacecraft to compensate solar irradiation. Thermally stable environment is very demanded for LISA performance verification. In a lab environment specifications can be met with considerable amount of insulation and thermal mass. For spacecraft, the very limited thermal mass calls for an active control system which can meet disturbance rejection and stability requirements simultaneously in the presence of long time delay. A simple proportional plus integral control law presently provides approximately 1 mK/√Hz of thermal stability for over 80 hours. Continuing development of a model predictive feed-forward algorithm will extend performance to below 1 mK/√Hz at f < 1 mHz and lower.

  10. Magnetic avalanches in granular ferromagnets: thermal activated collective behavior

    Science.gov (United States)

    Chern, Gia-Wei

    2017-02-01

    We present a numerical study on the thermal activated avalanche dynamics in granular materials composed of ferromagnetic clusters embedded in a non-magnetic matrix. A microscopic dynamical simulation based on the reaction-diffusion process is developed to model the magnetization process of such systems. The large-scale simulations presented here explicitly demonstrate inter-granular collective behavior induced by thermal activation of spin tunneling. In particular, we observe an intriguing criticality controlled by the rate of energy dissipation. We show that thermal activated avalanches can be understood in the framework of continuum percolation and the emergent dissipation induced criticality is in the universality class of 3D percolation transition. Implications of these results to the phase-separated states of colossal magnetoresistance materials and other artificial granular magnetic systems are also discussed.

  11. Activation of interfacial enzymes at membrane surfaces

    DEFF Research Database (Denmark)

    Mouritsen, Ole G.; Andresen, Thomas Lars; Halperin, Avi;

    2006-01-01

    A host of water-soluble enzymes are active at membrane surfaces and in association with membranes. Some of these enzymes are involved in signalling and in modification and remodelling of the membranes. A special class of enzymes, the phospholipases, and in particular secretory phospholipase A2 (s......PLA2), are only activated at the interface between water and membrane surfaces, where they lead to a break-down of the lipid molecules into lysolipids and free fatty acids. The activation is critically dependent on the physical properties of the lipid-membrane substrate. A topical review is given...

  12. Aspherical surfaces design for extreme ultraviolet lithographic objective with correction of thermal aberration

    Science.gov (United States)

    Liu, Yan; Li, Yanqiu

    2016-09-01

    At present, few projection objectives for extreme ultraviolet (EUV) lithography pay attention to correct thermal aberration in optical design phase, which would lead to poor image quality in a practical working environment. We present an aspherical modification method for helping the EUV lithographic objective additionally correct the thermal aberration. Based on the thermal aberration and deformation predicted by integrated optomechanical analysis, the aspherical surfaces in an objective are modified by an iterative algorithm. The modified aspherical surfaces could correct the thermal aberration and maintain the initial high image quality in a practical working environment. A six-mirror EUV lithographic objective with 0.33-numerical aperture is taken as an example to illustrate the presented method. The results show that the thermal aberration can be corrected effectively, and the image quality of the thermally deformed system is improved to the initial design level, which proves the availability of the method.

  13. Active micromixer using surface acoustic wave streaming

    Science.gov (United States)

    Branch; Darren W. , Meyer; Grant D. , Craighead; Harold G.

    2011-05-17

    An active micromixer uses a surface acoustic wave, preferably a Rayleigh wave, propagating on a piezoelectric substrate to induce acoustic streaming in a fluid in a microfluidic channel. The surface acoustic wave can be generated by applying an RF excitation signal to at least one interdigital transducer on the piezoelectric substrate. The active micromixer can rapidly mix quiescent fluids or laminar streams in low Reynolds number flows. The active micromixer has no moving parts (other than the SAW transducer) and is, therefore, more reliable, less damaging to sensitive fluids, and less susceptible to fouling and channel clogging than other types of active and passive micromixers. The active micromixer is adaptable to a wide range of geometries, can be easily fabricated, and can be integrated in a microfluidic system, reducing dead volume. Finally, the active micromixer has on-demand on/off mixing capability and can be operated at low power.

  14. Thermal and Photochemical Reactions of NO2 on a Chromium (III) Oxide Surface

    Science.gov (United States)

    Nishino, N.; Finlayson-Pitts, B. J.

    2011-12-01

    Chromium oxide (Cr2O3) is a major component of the oxide layer on stainless steel surfaces. It is also widely used as pigment in paints and roofs and as a protective coating on various surfaces. While many studies have focused on the catalytic activity of Cr2O3 surfaces for selective catalytic reduction (SCR), less attention has been paid to its surface chemistry involving atmospherically important species such as NO2 under atmospheric conditions. In this study, we have investigated thermal and photochemical reactions of NO2 in the presence and the absence of water vapor, using a thin layer of Cr2O3 as a model for the surface of stainless steel as well as other similarly coated surfaces in the boundary layer. A 30 nm thick Cr2O3 film was deposited on a germanium attenuated total reflectance (ATR) crystal, and the changes in the surface species were monitored by Fourier Transform Infrared (FTIR) spectroscopy. Upon NO2 adsorption, nitrate (NO3-) ions appeared likely coordinated to Cr3+ ion(s). The NO3- peaks reversibly shifted when water vapor was added, suggesting that NO3- become solvated. Irradiation at 311 nm led to a decrease in NO3- ions under both dry and humid conditions. The major gas-phase species formed by the irradiation was NO under dry conditions, while NO2 was mainly formed in the presence of H2O. Possible mechanisms and the implications for heterogeneous NO2 chemistry in the boundary layer will be discussed. The results will also be compared to similar chemistry on other surfaces.

  15. RESEARCH ON DISTURBED MECHANISM OF THERMAL NOISES OF THE SURFACE IN ABRUPT GEOTHERMAL ANOMALY

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Geothermal anomaly as a physical phenomenon of an active and latent volcanic area would be well recognized, and abrupt geothermal anomaly should also be understood. However, in practical work, thermal infrared remote sensing techniques are frequently used to monitor geothermal flows of the earth. But then, except for this type of thermal source in the surface thermal field, there still exist a lot of noises in the area where the abrupt geothermal anomaly is generated. By Analyzing the reason, we find that it is brought about by the non-boundless projectioncharacteristics of objects.These noises may be divided into two classes: system noises and random noises. If disturbednoises have comparative stable time sequence law and space sequence law, the noises are called system noises. And because system noises have a certain law, it is easy toremove the noises. On the contrary, if disturbed noises have not law oftime sequence and space sequence, the noises are called random noises. The random noises have the character of non-linearity, uncertainty and indeterminism. For this case, this paper discusses the disturbed mechanism of these noises as well as how to remove them.

  16. Surface Coatings for Low Emittance in the Thermal Surveillance Band

    Science.gov (United States)

    1984-08-01

    radiation emanating from the sky during the day and at night [13]; 2 - (2) -the geometry, surface topography, and surface cleanliness of the target and the... surface cleanliness . A description of terms and definitions used in reflectometry is provided by Judd [19] and Overington (20]. Measurement standards

  17. Thermally activated deformation of irradiated reactor pressure vessel steel

    Science.gov (United States)

    Böhmert, J.; Müller, G.

    2002-03-01

    Temperature and strain rate change tensile tests were performed on two VVER 1000-type reactor pressure vessel welds with different contents of nickel in unirradiated and irradiated conditions in order to determine the activation parameters of the contribution of the thermally activated deformation. There are no differences of the activation parameters in the unirradiated and the irradiated conditions as well as for the two different materials. This shows that irradiation hardening preferentially results from a friction hardening mechanism by long-range obstacles.

  18. Thermal Performance of Hollow Clay Brick with Low Emissivity Treatment in Surface Enclosures

    OpenAIRE

    Roberto Fioretti; Paolo Principi

    2014-01-01

    External walls made with hollow clay brick or block are widely used for their thermal, acoustic and structural properties. However, the performance of the bricks frequently does not conform with the minimum legal requirements or the values required for high efficiency buildings, and for this reason, they need to be integrated with layers of thermal insulation. In this paper, the thermal behavior of hollow clay block with low emissivity treatment on the internal cavity surfaces has been invest...

  19. Active thermal control for the 1.8-m primary mirror of the solar telescope CLST

    Science.gov (United States)

    Liu, Yangyi; Gu, Naiting; Li, Cheng; Cheng, Yuntao; Yao, Benxi; Wang, Zhiyong; Rao, Changhui

    2016-07-01

    The 1.8-m primary mirror of solar telescope is heated by the solar radiation and introduce harmful mirror seeing degrading the imaging quality. For the Chinese Large Solar Telescope (CLST), the thermal requirement based on the quantitative evaluation on mirror seeing effect shows that the temperature rise on mirror surface should be within 1 kelvin. To meet the requirement, an active thermal control system design for the CLST primary mirror is proposed, and realized on the subscale prototype of the CLST. The experimental results show that the temperature on the mirror surface is well controlled. The average and maximum thermal controlled error are less than 0.3 and 0.7 kelvins respectively, which completely meets the requirements.

  20. Surface Response of Brominated Carbon Media on Laser and Thermal Excitation: Optical and Thermal Analysis Study

    Science.gov (United States)

    Multian, Volodymyr V.; Kinzerskyi, Fillip E.; Vakaliuk, Anna V.; Grishchenko, Liudmyla M.; Diyuk, Vitaliy E.; Boldyrieva, Olga Yu.; Kozhanov, Vadim O.; Mischanchuk, Oleksandr V.; Lisnyak, Vladyslav V.; Gayvoronsky, Volodymyr Ya.

    2017-02-01

    The present study is objected to develop an analytical remote optical diagnostics of the functionalized carbons surface. Carbon composites with up to 1 mmol g-1 of irreversibly adsorbed bromine were produced by the room temperature plasma treatment of an activated carbon fabric (ACF) derived from polyacrylonitrile textile. The brominated ACF (BrACF) was studied by elastic optical scattering indicatrix analysis at wavelength 532 nm. The obtained data were interpreted within results of the thermogravimetric analysis, X-ray photoelectron spectroscopy and temperature programmed desorption mass spectrometry. The bromination dramatically reduces the microporosity producing practically non-porous material, while the incorporated into the micropores bromine induces the dielectric and structural impact on surface polarizability and conductivity due to the charging effect. We have found that the elastic optical scattering in proper solid angles in the forward and the backward hemispheres is sensitive to the kind of the bromine bonding, e.g., physical adsorption or chemisorption, and the bromination level, respectively, that can be utilized for the express remote fabrication control of the nanoscale carbons with given interfaces.

  1. Adsorption of atrazine on hemp stem-based activated carbons with different surface chemistry

    OpenAIRE

    Lupul, Iwona; Yperman, Jan; Carleer, Robert; Gryglewicz, Grazyna

    2015-01-01

    Surface-modified hemp stem-based activated carbons (HACs) were prepared and used for the adsorption of atrazine from aqueous solution, and their adsorption performance was examined. A series of HACs were prepared by potassium hydroxide activation of hemp stems, followed by subsequent modification by thermal annealing, oxidation with nitric acid and amination. The resultant HACs differed in surface chemistry, while possessing similar porous structure. The surface group characteristics were exa...

  2. Thermal Performance of Hollow Clay Brick with Low Emissivity Treatment in Surface Enclosures

    Directory of Open Access Journals (Sweden)

    Roberto Fioretti

    2014-10-01

    Full Text Available External walls made with hollow clay brick or block are widely used for their thermal, acoustic and structural properties. However, the performance of the bricks frequently does not conform with the minimum legal requirements or the values required for high efficiency buildings, and for this reason, they need to be integrated with layers of thermal insulation. In this paper, the thermal behavior of hollow clay block with low emissivity treatment on the internal cavity surfaces has been investigated. The purpose of this application is to obtain a reduction in the thermal conductivity of the block by lowering the radiative heat exchange in the enclosures. The aims of this paper are to indicate a methodology for evaluating the thermal performance of the brick and to provide information about the benefits that should be obtained. Theoretical evaluations are carried out on several bricks (12 geometries simulated with two different thermal conductivities of the clay, using a finite elements model. The heat exchange procedure is implemented in accordance with the standard, so as to obtain standardized values of the thermal characteristics of the block. Several values of emissivity are hypothesized, related to different kinds of coating. Finally, the values of the thermal transmittance of walls built with the evaluated blocks have been calculated and compared. The results show how coating the internal surface of the cavity provides a reduction in the thermal conductivity of the block, of between 26% and 45%, for a surface emissivity of 0.1.

  3. The thermal energy of a scalar field on a unidimensional Riemann surface

    CERN Document Server

    Elizalde, E

    2002-01-01

    We discuss some controverted aspects of the evaluation of the thermal energy of a scalar field on a unidimensional Riemann surface. The calculations are carried out using a generalised zeta function approach.

  4. Surface complex formation between aliphatic nitrile molecules and transition metal atoms for thermally stable lithium-ion batteries.

    Science.gov (United States)

    Kim, Young-Soo; Lee, Hochun; Song, Hyun-Kon

    2014-06-11

    Non-flammability of electrolyte and tolerance of cells against thermal abuse should be guaranteed for widespread applications of lithium-ion batteries (LIBs). As a strategy to improve thermal stability of LIBs, here, we report on nitrile-based molecular coverage on surface of cathode active materials to block or suppress thermally accelerated side reactions between electrode and electrolyte. Two different series of aliphatic nitriles were introduced as an additive into a carbonate-based electrolyte: di-nitriles (CN-[CH2]n-CN with n = 2, 5, and 10) and mono-nitriles (CH3-[CH2]m-CN with m = 2, 5, and 10). On the basis of the strong interaction between the electronegativity of nitrile functional groups and the electropositivity of cobalt in LiCoO2 cathode, aliphatic mono- and di-nitrile molecules improved the thermal stability of lithium ion cells by efficiently protecting the surface of LiCoO2. Three factors, the surface coverage θ, the steric hindrance of aliphatic moiety within nitrile molecule, and the chain polarity, mainly affect thermal tolerance as well as cell performances at elevated temperature.

  5. Self-activated, self-limiting reactions on Si surfaces

    DEFF Research Database (Denmark)

    Morgen, Per; Hvam, Jeanette; Bahari, Ali

    The direct thermally activated reactions of oxygen and ammonia with Si surfaces in furnaces have been used for a very long time in the semiconductor industry for the growth of thick oxides and nitride layers respectively. The oxidation mechanism was described in the Deal-Grove model as a diffusion...... limited transport of oxygen to the oxide/silicon interface. For thin oxides the deal-Grove growth rate is initially constant, but for ultrathin oxides (a couple of nm thick) this is not true and the Deal-Grove model does not explain the mechanism. In a series of recent reports we have found a new...

  6. Formation of Embedded Microstructures by Thermal Activated Solvent Bonding

    CERN Document Server

    Ng, S H; Wang, Z F; Lu, A C W; Rodriguez, I; De Rooij, N

    2008-01-01

    We present a thermal activated solvent bonding technique for the formation of embedded microstrucutres in polymer. It is based on the temperature dependent solubility of polymer in a liquid that is not a solvent at room temperature. With thermal activation, the liquid is transformed into a solvent of the polymer, creating a bonding capability through segmental or chain interdiffusion at the bonding interface. The technique has advantages over the more commonly used thermal bonding due to its much lower operation temperature (30 degrees C lower than the material's Tg), lower load, as well as shorter time. Lap shear test indicated bonding shear strength of up to 2.9 MPa. Leak test based on the bubble emission technique showed that the bonded microfluidic device can withstand at least 6 bars (87 psi) of internal pressure (gauge) in the microchannel. This technique can be applied to other systems of polymer and solvent.

  7. Modeling thermally active building components using space mapping

    DEFF Research Database (Denmark)

    Pedersen, Frank; Weitzmann, Peter; Svendsen, Svend

    2005-01-01

    In order to efficiently implement thermally active building components in new buildings, it is necessary to evaluate the thermal interaction between them and other building components. Applying parameter investigation or numerical optimization methods to a differential-algebraic (DAE) model....... This paper describes the principle of the space mapping technique, and introduces a simple space mapping technique. The technique is applied to a lumped parameter model of a thermo active component, which provides a model of the thermal performance of the component as a function of two design parameters...... of a building provides a systematic way of estimating efficient building designs. However, using detailed numerical calculations of the components in the building is a time consuming process, which may become prohibitive if the DAE model is to be used for parameter variation or optimization. Unfortunately...

  8. Two-Phase Thermal Switching System for a Small, Extended Duration Lunar Surface Science Platform

    Science.gov (United States)

    Bugby, David C.; Farmer, Jeffery T.; OConnor, Brian F.; Wirzburger, Melissa J.; Abel, Elisabeth D.; Stouffer, Chuck J.

    2010-01-01

    This paper describes a novel thermal control system for the Warm Electronics Box (WEB) on board a small lunar surface lander intended to support science activities anywhere on the lunar surface for an extended duration of up to 6 years. Virtually all lander electronics, which collectively dissipate about 60 W in the reference mission, are contained within the WEB. These devices must be maintained below 323 K (with a goal of 303 K) during the nearly 15-earth-day lunar day, when surface temperatures can reach 390K, and above 263 K during the nearly 15-earth-day lunar night, when surface temperatures can reach 100K. Because of the large temperature swing from lunar day-to-night, a novel thermal switching system was required that would be able to provide high conductance from WEB to radiator(s) during the hot lunar day and low (or negligible) conductance during the cold lunar night. The concept that was developed consists of ammonia variable conductance heat pipes (VCHPs) to collect heat from WEB components and a polymer wick propylene loop heat pipe (LHP) to transport the collected heat to the radiator(s). The VCHPs autonomously maximize transport when the WEB is warm and autonomously shut down when the WEB gets cold. The LHP autonomously shuts down when the VCHPs shut down. When the environment transitions from lunar night to day, the VCHPs and LHP autonomously turn back on. Out of 26 analyzed systems, this novel arrangement was able to best achieve the combined goals of zero control power, autonomous operation, long life, low complexity, low T, and landed tilt tolerance.

  9. Thermal diffusion of potassium on the modified iron surface

    Energy Technology Data Exchange (ETDEWEB)

    Narkiewicz, U. [Institute of Chemical and Environment Engineering, Technical University of Szczecin, PuIaskiego 10, 70-322 Szczecin (Poland)]. E-mail: urszula.narkiewicz@ps.pl; Moszynski, D. [Institute of Chemical and Environment Engineering, Technical University of Szczecin, PuIaskiego 10, 70-322 Szczecin (Poland); BrosIawski, M. [Institute of Chemical and Environment Engineering, Technical University of Szczecin, PuIaskiego 10, 70-322 Szczecin (Poland)

    2005-10-31

    The diffusion of potassium on the polycrystalline iron surface modified by adsorbed oxygen and nitrogen has been studied by means of AES. The migration of potassium atoms has been observed independently on the constitution of the iron surface in the temperature range between 300 and 450 deg. C. The final concentration of potassium on the iron surface increases with temperature from 300 to 400 deg. C, irrespective of what atoms accompany potassium on the surface. At 450 deg. C, the final level of potassium concentration is decreased. The profiles of the concentration on the surface along the line crossing the source of potassium were also acquired. Applying the diffusion model of finite source, the diffusion coefficient of potassium for oxygen-covered and nitrogen-covered surfaces were evaluated.

  10. JCMT active surface control system: implementation

    Science.gov (United States)

    Smith, Ian A.

    1998-05-01

    The James Clerk Maxwell Telescope on the summit of Mauna Kea in Hawaii is a 15 meter sub-millimeter telescope which operates in the 350 microns to 2 millimeter region. The primary antenna surface consists of 276 panels, each of which is positioned by 3 stepper motors. In order to achieve the highest possible surface accuracy we are embarking upon a project to actively control the position of the panels adjuster system is based on a 6809 micro connected to the control computer by a GPIB interface. This system is slow and inflexible and it would prove difficult to build an active surface control system with it. Part of the upgrade project is to replace the existing micro with a 68060 VME micro. The poster paper will describe how the temperature of the antenna is monitored with the new system, how a Finite Element Analyses package transforms temperature changes into a series of panel adjuster moves, and how these moves are then applied to the surface. The FEA package will run on a high end Sun workstation. A series of DRAMA tasks distributed between the workstation and the Baja 68060 VxWorks Active Surface Control System micro will control the temperature monitoring, FEA and panel adjustment activities. Users can interact with the system via a Tcl/TK based GUI.

  11. Investigation of thermal effect on exterior wall surface of building material at urban city area

    OpenAIRE

    Mohd Fadhil Md Din, Hazlini Dzinun, M. Ponraj, Shreeshivadasan Chelliapan, Zainura Zainun Noor, Dilshah Remaz, Kenzo Iwao

    2012-01-01

    This paper describes the investigation of heat impact on the vertical surfaces of buildings based on their thermal behavior. The study was performed based on four building materials that is commonly used in Malaysia; brick, concrete, granite and white concrete tiles. The thermal performances on the building materials were investigated using a surface temperature sensor, data logging system and infrared thermography. Results showed that the brick had the capability to absorb and store heat gre...

  12. Thermal migration of deuterium implanted in graphite: Influence of free surface proximity and structure

    Science.gov (United States)

    Le Guillou, M.; Moncoffre, N.; Toulhoat, N.; Pipon, Y.; Ammar, M. R.; Rouzaud, J. N.; Deldicque, D.

    2016-03-01

    This paper is a contribution to the study of the behavior of activation products produced in irradiated nuclear graphite, graphite being the moderator of the first French generation of CO2 cooled nuclear fission reactors. This paper is focused on the thermal release of Tritium, a major contributor to the initial activity, taking into account the role of the free surfaces (open pores and graphite surface). Two kinds of graphite were compared. On one hand, Highly Oriented Pyrolitic Graphite (HOPG), a model well graphitized graphite, and on the other hand, SLA2, a porous less graphitized nuclear graphite. Deuterium ion implantation at three different energies 70, 200 and 390 keV allows simulating the presence of Tritium at three different depths, corresponding respectively to projected ranges Rp of 0.75, 1.7 and 3.2 μm. The D isotopic tracing is performed thanks to the D(3He,p)4He nuclear reaction. The graphite structure is studied by Raman microspectrometry. Thermal annealing is performed in the temperature range 200-1200 °C up to 300 h annealing time. As observed in a previous study, the results show that the D release occurs according to three kinetic regimes: a rapid permeation through open pores, a transient regime corresponding to detrapping and diffusion of D located at low energy sites correlated to the edges of crystallites and finally a saturation regime attributed to detrapping of interstitial D located at high energy sites inside the crystallites. Below 600 °C, D release is negligible whatever the implantation depth and the graphite type. The present paper clearly puts forward that above 600 °C, the D release decreases at deeper implantation depths and strongly depends on the graphite structure. In HOPG where high energy sites are more abundant, the D release is less dependent on the surface proximity compared to SLA2. In SLA2, in which the low energy sites prevail, the D release curves are clearly shifted towards lower temperatures when D is located

  13. Thermal migration of deuterium implanted in graphite: Influence of free surface proximity and structure

    Energy Technology Data Exchange (ETDEWEB)

    Le Guillou, M. [Institut de Physique Nucléaire de Lyon, CNRS/IN2P3 UMR 5822, Université Claude Bernard Lyon 1, Université de Lyon, F-69622 Villeurbanne cedex (France); Moncoffre, N., E-mail: n.moncoffre@ipnl.in2p3.fr [Institut de Physique Nucléaire de Lyon, CNRS/IN2P3 UMR 5822, Université Claude Bernard Lyon 1, Université de Lyon, F-69622 Villeurbanne cedex (France); Toulhoat, N. [Institut de Physique Nucléaire de Lyon, CNRS/IN2P3 UMR 5822, Université Claude Bernard Lyon 1, Université de Lyon, F-69622 Villeurbanne cedex (France); CEA/DEN – Centre de Saclay, F-91191 Gif-sur-Yvette cedex (France); Pipon, Y. [Institut de Physique Nucléaire de Lyon, CNRS/IN2P3 UMR 5822, Université Claude Bernard Lyon 1, Université de Lyon, F-69622 Villeurbanne cedex (France); Institut Universitaire Technologique, Université Claude Bernard Lyon 1, Université de Lyon, F-69622 Villeurbanne cedex (France); Ammar, M.R. [CNRS, CEMHTI UPR3079, Université Orléans, CS90055, F-45071 Orléans cedex 2 (France); Rouzaud, J.N.; Deldicque, D. [Laboratoire de Géologie de l’Ecole Normale Supérieure, Paris, UMR CNRS ENS 8538, F-75231 Paris cedex 5 (France)

    2016-03-15

    This paper is a contribution to the study of the behavior of activation products produced in irradiated nuclear graphite, graphite being the moderator of the first French generation of CO{sub 2} cooled nuclear fission reactors. This paper is focused on the thermal release of Tritium, a major contributor to the initial activity, taking into account the role of the free surfaces (open pores and graphite surface). Two kinds of graphite were compared. On one hand, Highly Oriented Pyrolitic Graphite (HOPG), a model well graphitized graphite, and on the other hand, SLA2, a porous less graphitized nuclear graphite. Deuterium ion implantation at three different energies 70, 200 and 390 keV allows simulating the presence of Tritium at three different depths, corresponding respectively to projected ranges R{sub p} of 0.75, 1.7 and 3.2 μm. The D isotopic tracing is performed thanks to the D({sup 3}He,p){sup 4}He nuclear reaction. The graphite structure is studied by Raman microspectrometry. Thermal annealing is performed in the temperature range 200–1200 °C up to 300 h annealing time. As observed in a previous study, the results show that the D release occurs according to three kinetic regimes: a rapid permeation through open pores, a transient regime corresponding to detrapping and diffusion of D located at low energy sites correlated to the edges of crystallites and finally a saturation regime attributed to detrapping of interstitial D located at high energy sites inside the crystallites. Below 600 °C, D release is negligible whatever the implantation depth and the graphite type. The present paper clearly puts forward that above 600 °C, the D release decreases at deeper implantation depths and strongly depends on the graphite structure. In HOPG where high energy sites are more abundant, the D release is less dependent on the surface proximity compared to SLA2. In SLA2, in which the low energy sites prevail, the D release curves are clearly shifted towards lower

  14. One-dimensional models of thermal activation under shear stress

    CSIR Research Space (South Africa)

    Nabarro, FRN

    2003-01-01

    Full Text Available The analysis of thermal activation under shear stress in three- and even two-dimensional models presents unresolved problems. The analysis of one-dimensional models presented here may illuminate the study of more realistic models. For the model...

  15. Cyclic softening and thermally activated deformation of titanium and zirconium

    Energy Technology Data Exchange (ETDEWEB)

    Dickson, J.I.; Handfield, L.; L' Esperance, G. (Ecole Polytechnique, Montreal, Quebec (Canada). Dept. de Genie Metallurgique)

    1983-08-01

    Cyclic softening in commercial purity zirconium and titanium corresponds principally to a decrease in effective stress and to an increase in screw dislocation mobility. This result indicates that the thermally activated deformation of these metals is not controlled by the overcoming of individual interstitial solute atoms by dislocations as usually proposed.

  16. Behaviour of Self-Standing CVD Diamond Film with Different Dominant Crystalline Surfaces in Thermal-Iron Plate Polishing

    Institute of Scientific and Technical Information of China (English)

    CHEN Guang-Chao; ZHOU Zu-Yuan; LI Bin; ZHOU You-Liang; J. Askri; LI Cheng-Ming; TANG Wei-Zhong; TONG Yu-Mei; LU Fan-Xiu

    2006-01-01

    @@ Self-standing CVD diamond films with different dominant crystalline surfaces are polished by the thermal-iron plate polishing method. The influence of the dominant crystalline surfaces on polishing efficiency is investigated by measuring the removal rate and final roughness. The smallest rms roughness of 0.14μm is measured with smallest removal rate in the films with the initial (220) dominant crystalline surface. Activation energy for the polishing is analysed by the Arrhenius relation. It is found that the values are 170kJ/mol, 222kJ/mol and 214kJ/mol for the film with t hree different dominant crystalline surfaces. Based on these values, the polishing cause is regarded as the graphitization-controlling process. In the experiment, we find that transformation of the dominant crystalline surfaces from (111) to (220) always appears in the polishing process when we polish the (111) dominant surface.

  17. Surface state of GaN after rapid-thermal-annealing using AlN cap-layer

    Science.gov (United States)

    El-Zammar, G.; Khalfaoui, W.; Oheix, T.; Yvon, A.; Collard, E.; Cayrel, F.; Alquier, D.

    2015-11-01

    Critical issues need to be overcome to produce high performance Schottky diodes on gallium nitride (GaN). To activate dopant, high temperature thermal treatments are required but damage GaN surface where hexagonal pits appear and prevent any device processing. In this paper, we investigated the efficiency of cap-layers on GaN during thermal treatments to avoid degradation. Aluminum nitride (AlN) and silicon oxide (SiOx) were grown on GaN by direct current reactive magnetron sputtering and plasma-enhanced chemical vapor deposition, respectively. AlN growth parameters were studied to understand their effect on the grown layers and their protection efficiency. Focused ion beam was used to measure AlN layer thickness. Crystalline quality and exact composition were verified using X-ray diffraction and energy dispersive X-ray spectroscopy. Two types of rapid thermal annealing at high temperatures were investigated. Surface roughness and pits density were evaluated using atomic force microscopy and scanning electron microscopy. Cap-layers wet etching was processed in H3PO4 at 120 °C for AlN and in HF (10%) for SiOx. This work reveals effective protection of GaN during thermal treatments at temperatures as high as 1150 °C. Low surface roughness was obtained. Furthermore, no hexagonal pit was observed on the surface.

  18. Near-surface Thermal Infrared Imaging of a Mixed Forest

    Science.gov (United States)

    Aubrecht, D. M.; Helliker, B. R.; Richardson, A. D.

    2014-12-01

    Measurement of an organism's temperature is of basic physiological importance and therefore necessary for ecosystem modeling, yet most models derive leaf temperature from energy balance arguments or assume it is equal to air temperature. This is because continuous, direct measurement of leaf temperature outside of a controlled environment is difficult and rarely done. Of even greater challenge is measuring leaf temperature with the resolution required to understand the underlying energy balance and regulation of plant processes. To measure leaf temperature through the year, we have mounted a high-resolution, thermal infrared camera overlooking the canopy of a temperate deciduous forest. The camera is co-located with an eddy covariance system and a suite of radiometric sensors. Our camera measures longwave thermal infrared (λ = 7.5-14 microns) using a microbolometer array. Suspended in the canopy within the camera FOV is a matte black copper plate instrumented with fine wire thermocouples that acts as a thermal reference for each image. In this presentation, I will discuss the challenges of continuous, long-term field operation of the camera, as well as measurement sensitivity to physical and environmental parameters. Based on this analysis, I will show that the uncertainties in converting radiometric signal to leaf temperature are well constrained. The key parameter for minimizing uncertainty is the emissivity of the objects being imaged: measuring the emissivity to within 0.01 enables leaf temperature to be calculated to within 0.5°C. Finally, I will present differences in leaf temperature observed amongst species. From our two-year record, we characterize high frequency, daily, and seasonal thermal signatures of leaves and crowns, in relation to environmental conditions. Our images are taken with sufficient spatial and temporal resolution to quantify the preferential heating of sunlit portions of the canopy and the cooling effect of wind gusts. Future work will

  19. Electron beam induced surface activation of oxide surfaces for nanofabrication

    Energy Technology Data Exchange (ETDEWEB)

    Vollnhals, Florian; Seiler, Steffen; Walz, Marie-Madeleine; Steinrueck, Hans-Peter; Marbach, Hubertus [Lehrstuhl fuer Physikalische Chemie II and Interdisciplinary Center for Molecular Materials (ICMM), Friedrich-Alexander-Universitaet Erlangen-Nuernberg, Erlangen (Germany); Woolcot, Tom; Thornton, Geoff [London Centre for Nanotechnology and Department of Chemistry, University College London (United Kingdom)

    2012-07-01

    The controlled fabrication of structures on the nanoscale is a major challenge in science and engineering. Direct-write techniques like Electron Beam Induced Deposition (EBID) were shown to be suitable tools in this context. Recently, Electron Beam Induced Surface Activation (EBISA) has been introduced as a new focused electron beam technique. In EBISA, a surface, e.g. SiO{sub 2}, is irradiated by a focused electron beam, resulting in an activation of the exposed area. The activated area can then react and decompose precursor gases like iron pentacarbonyl, Fe(CO){sub 5}. This leads to a primary deposit, which continues to grow autocatalytically as long as Fe(CO){sub 5} is supplied, resulting in pure (> 90 % at.), crystalline iron nanostructures. We expand the use of this concept by exploring EBISA to produce metallic nanostructures on TiO{sub 2}(110) in UHV; atomistic insight into the process is obtained via Scanning Tunneling Microscopy (STM) and chemical insight via Auger Electron Spectroscopy (AES).

  20. Pharmacological activities in thermal proteins: relationships in molecular evolution

    Science.gov (United States)

    Fox, S. W.; Hefti, F.; Hartikka, J.; Junard, E.; Przybylski, A. T.; Vaughan, G.

    1987-01-01

    The model of protobiological events that has been presented in these pages has increasing relevance to pharmacological research. The thermal proteins that function as key substances in the proteinoid theory have recently been found to prolong the survival of rat forebrain neurons in culture and to stimulate the growth of neurites. A search for such activity in thermal proteins added to cultures of modern neurons was suggested by the fact that some of the microspheres assembled from proteinoids rich in hydrophobic amino acids themselves generate fibrous outgrowths.

  1. The surface roughness of (433) Eros as measured by thermal-infrared beaming

    Science.gov (United States)

    Rozitis, B.

    2017-01-01

    In planetary science, surface roughness is regarded to be a measure of surface irregularity at small spatial scales, and causes the thermal-infrared beaming effect (i.e. re-radiation of absorbed sunlight back towards to the Sun). Typically, surface roughness exhibits a degeneracy with thermal inertia when thermophysical models are fitted to disc-integrated thermal-infrared observations of asteroids because of this effect. In this work, it is demonstrated how surface roughness can be constrained for near-Earth asteroid (433) Eros (i.e. the target of NASA's NEAR Shoemaker mission) when using the Advanced Thermophysical Model with thermal-infrared observations taken during an `almost pole-on' illumination and viewing geometry. It is found that the surface roughness of (433) Eros is characterized by an rms slope of 38 ± 8° at the 0.5-cm spatial scale associated with its thermal-infrared beaming effect. This is slightly greater than the rms slope of 25 ± 5° implied by the NEAR Shoemaker laser ranging results when extrapolated to this spatial scale, and indicates that other surface shaping processes might operate, in addition to collisions and gravity, at spatial scales under one metre in order to make asteroid surfaces rougher. For other high-obliquity asteroids observed during `pole-on' illumination conditions, the thermal-infrared beaming effect allows surface roughness to be constrained when the sub-solar latitude is greater than 60°, and if the asteroids are observed at phase angles of less than 40°. They will likely exhibit near-Earth asteroid thermal model beaming parameters that are lower than expected for a typical asteroid at all phase angles up to 100°.

  2. A novel approach to generate random surface thermal loads in piping

    Energy Technology Data Exchange (ETDEWEB)

    Costa Garrido, Oriol, E-mail: oriol.costa@ijs.si; El Shawish, Samir; Cizelj, Leon

    2014-07-01

    Highlights: • Approach for generating continuous and time-dependent random thermal fields. • Temperature fields simulate fluid mixing thermal loads at fluid–wall interface. • Through plane-wave decomposition, experimental temperature statistics are reproduced. • Validation of the approach with a case study from literature. • Random surface thermal loads generation for future thermal fatigue analyses of piping. - Abstract: There is a need to perform three-dimensional mechanical analyses of pipes, subjected to complex thermo-mechanical loadings such as the ones evolving from turbulent fluid mixing in a T-junction. A novel approach is proposed in this paper for fast and reliable generation of random thermal loads at the pipe surface. The resultant continuous and time-dependent temperature fields simulate the fluid mixing thermal loads at the fluid–wall interface. The approach is based on reproducing discrete fluid temperature statistics, from experimental readings or computational fluid dynamic simulation's results, at interface locations through plane-wave decomposition of temperature fluctuations. The obtained random thermal fields contain large scale instabilities such as cold and hot spots traveling at flow velocities. These low frequency instabilities are believed to be among the major causes of the thermal fatigue in T-junction configurations. The case study found in the literature has been used to demonstrate the generation of random surface thermal loads. The thermal fields generated with the proposed approach are statistically equivalent (within the first two moments) to those from CFD simulations results of similar characteristics. The fields maintain the input data at field locations for a large set of parameters used to generate the thermal loads. This feature will be of great advantage in future sensitivity fatigue analyses of three-dimensional pipe structures.

  3. Infrared thermal mapping of the martian surface and atmosphere: first results.

    Science.gov (United States)

    Kieffer, H H; Chase, S C; Miner, E D; Palluconi, F D; Münch, G; Neugebauer, G; Martin, T Z

    1976-08-27

    The Viking infrared thermal mapper measures the thermal emission of the martian surface and atmosphere and the total reflected sunlight. With the high resolution and dense coverage being achieved, planetwide thermal structure is apparent at large and small scales. The thermal behavior of the best-observed areas, the landing sites, cannot be explained by simple homogeneous models. The data contain clear indications for the relevance of additional factors such as detailed surface texture and the occurrence of clouds. Areas in the polar night have temperatures distinctly lower than the CO(2) condensation point at the surface pressure. This observation implies that the annual atmospheric condensation is less than previously assumed and that either thick CO(2) clouds exist at the 20-kilometer level or that the polar atmosphere is locally enriched by noncondensable gases.

  4. Infrared thermal mapping of the Martian surface and atmosphere - First results

    Science.gov (United States)

    Kieffer, H. H.; Martin, T. Z.; Chase, S. C., Jr.; Miner, E. D.; Palluconi, F. D.; Muench, G.; Neugebauer, G.

    1976-01-01

    The Viking infrared thermal mapper measures the thermal emission of the Martian surface and atmosphere and the total reflected sunlight. With the high resolution and dense coverage being achieved, planetwide thermal structure is apparent at large and small scales. The thermal behavior of the best-observed areas, the landing sites, cannot be explained by simple homogeneous models. The data contain clear indications for the relevance of additional factors such as detailed surface texture and the occurrence of clouds. Areas in the polar night have temperatures distinctly lower than the CO2 condensation point at the surface pressure. This observation implies that the annual atmospheric condensation is less than previously assumed and that either thick CO2 clouds exist at the 20-kilometer level or that the polar atmosphere is locally enriched by noncondensable gases.

  5. Enhanced Thermal Transport of Surfaces with Superhydrophobic Coatings

    Science.gov (United States)

    2015-07-01

    Deposition 4 3. Results/ Analysis 5 4. Conclusion 7 5. References 8 Distribution List 9 iv List of Figures Fig. 1 Contact angle...by measuring the contact angle (σ) formed between a droplet of liquid and the surface (Fig. 1). Qualitatively , surfaces with a water contact angle...several seconds and dried with filtered nitrogen. The samples were then immersed in 0.01-M aqueous solution of silver nitrate for 20 s. The deposition

  6. Thermal desorption from surfaces with laser-induced defects

    Energy Technology Data Exchange (ETDEWEB)

    Szabelski, Pawel; Panczyk, Tomasz; Rudzinski, Wladyslaw

    2002-12-30

    Monte Carlo simulation method was used to mimic surface damage development caused by short laser pulses. The influence of pulsed laser irradiation on the creation of defect concentration was examined in the case of a model surface. In particular, the dependence of the intact surface area on a number of laser scans was studied and compared with the experimental results obtained for Rh(1 1 1) crystal face. Changes in the adsorptivoperties of the surface produced by laser irradiation are explained with the help of a simple geometric model connecting the laser intensity and the disordered area generated by a single laser shot. It was demonstrated that exponential decay of the Low Energy Electron Diffraction (LEED) signal with the number of laser scans, which is observed experimentally, may result directly from the overlapping of the laser spots created on the surface. This effect becomes enhanced when the laser intensity, hence the spot size, increases. The importance of laser-induced defects in the kinetics of catalytic/separation processes was examined in the case of temperature programmed desorption (TPD) spectra from surfaces subjected to a different number of laser shots. The spectra were simulated by employing the Monte Carlo method as well as by application of the absolute rate theory (ART) coupled with the mean field approximation. The results obtained with both methods were in a good agreement even when weak lateral interactions in the adsorbed phase were allowed.

  7. The surface quasiliquid melt acceleration and the role of thermodynamic phase in the thermal decomposition of crystalline organic explosives

    Energy Technology Data Exchange (ETDEWEB)

    Henson, Bryan F [Los Alamos National Laboratory

    2010-01-01

    We show that melt acceleration in the thermal decomposition of crystalline organic solids is a manifestation of the surface quasiliquid phase. We derive a single universal rate law for melt acceleration that is a simple function of the metastable liquid activity below the melting point, and has a zero order term proportional to the quasiliquid thickness. We argue that the underlying mechanisms of this model will provide a molecular definition for the stability of the class of secondary explosives.

  8. Mechanotransductive surfaces for reversible biocatalysis activation

    Science.gov (United States)

    Mertz, Damien; Vogt, Cédric; Hemmerlé, Joseph; Mutterer, Jérôme; Ball, Vincent; Voegel, Jean-Claude; Schaaf, Pierre; Lavalle, Philippe

    2009-09-01

    Fibronectin, like other proteins involved in mechanotransduction, has the ability to exhibit recognition sites under mechanical stretch. Such cryptic sites are buried inside the protein structure in the native fold and become exposed under an applied force, thereby activating specific signalling pathways. Here, we report the design of new active polymeric nanoassembled surfaces that show some similarities to these cryptic sites. These nanoassemblies consist of a first polyelectrolyte multilayer stratum loaded with enzymes and capped with a second polyelectrolyte multilayer acting as a mechanically sensitive nanobarrier. The biocatalytic activity of the film is switched on/off reversibly by mechanical stretching, which exposes enzymes through the capping barrier, similarly to mechanisms involved in proteins during mechanotransduction. This first example of a new class of biologically inspired surfaces should have great potential in the design of various devices aimed to trigger and modulate chemical reactions by mechanical action with applications in the field of microfluidic devices or mechanically controlled biopatches for example.

  9. Thermal dynamics of silver clusters grown on rippled silica surfaces

    Science.gov (United States)

    Bhatnagar, Mukul; Ranjan, Mukesh; Jolley, Kenny; Lloyd, Adam; Smith, Roger; Mukherjee, Subroto

    2017-02-01

    Silver nanoparticles have been deposited on silicon rippled patterned templates at an angle of incidence of 70° to the surface normal. The templates are produced by oblique incidence argon ion bombardment and as the fluence increases, the periods and heights of the structures increase. Structures with periods of 20 nm, 35 nm and 45 nm have been produced. Moderate temperature vacuum annealing shows the phenomenon of cluster coalescence following the contour of the more exposed faces of the ripple for the case of 35 nm and 45 nm but not at 20 nm where the silver aggregates into larger randomly distributed clusters. In order to understand this effect, the morphological changes of silver nanoparticles deposited on an asymmetric rippled silica surface are investigated through the use of molecular dynamics simulations for different deposition angles of incidence between 0° and 70° and annealing temperatures between 500 K and 900 K. Near to normal incidence, clusters are observed to migrate over the entire surface but for deposition at 70°, a similar patterning is observed as in the experiment. The random distribution of clusters for the periodicity ≈ of 20 nm is linked to the geometry of the silica surface which has a lower ripple height than the longer wavelength structures. Calculations carried out on a surface with such a lower ripple height also demonstrate a similar effect.

  10. Self-activated, self-limiting reactions on Si surfaces

    DEFF Research Database (Denmark)

    Morgen, Per; Hvam, Jeanette; Bahari, Ali

    mechanism for the direct growth of ultrathin films (0-3 nm) of oxides and nitrides under ultrahigh vacuum conditions. Neutral oxygen and a microwave excited nitrogen plasma interact directly with Si surfaces kept at different temperatures during the reaction. The gas pressures are around 10-6 Torr......The direct thermally activated reactions of oxygen and ammonia with Si surfaces in furnaces have been used for a very long time in the semiconductor industry for the growth of thick oxides and nitride layers respectively. The oxidation mechanism was described in the Deal-Grove model as a diffusion......, and the temperatures vary from room temperature to 10000C.The growth is in these cases self-limiting, with the optimal oxide thickness around 0.7-0.8 nm, at 5000C, and up to a few nm for nitride. The self-limiting oxide case was recently predicted by Alex Demkov in a structural optimization to minimise the total...

  11. The effect of surface roughness on thermal-elasto-hydrodynamic model of contact mechanical seals

    Science.gov (United States)

    Wen, QingFeng; Liu, Ying; Huang, WeiFeng; Suo, ShuangFu; Wang, YuMing

    2013-10-01

    In this paper, the effect of surface roughness on sealing clearance, pressure distribution, friction torque and leakage is studied by the thermal-elasto-hydrodynamic mixed lubrication model. A convergent nominal clearance is formed by the pressure deformation and thermal deformation of the seal faces. This causes more serious wear in the inner side than that of the outer side of the contact area. Mass leakage increases with the growing of the surface roughness. The temperature and thermal deformation on the seal surface increases substantially if the roughness is reduced. The contact mechanical seals have consistent performance when the standard deviation of surface roughness is approximately 0.2 μm. In order to validate the theoretical analysis model, a method combining the measurement of three-dimensioned profile and Raman spectrum is proposed.

  12. Chemical reactions in dense monolayers: in situ thermal cleavage of grafted esters for preparation of solid surfaces functionalized with carboxylic acids.

    Science.gov (United States)

    Dugas, Vincent; Chevalier, Yves

    2011-12-06

    The thermodynamics of a chemical reaction confined at a solid surface was investigated through kinetic measurements of a model unimolecular reaction. The thermal cleavage of ester groups grafted at the surface of solid silica was investigated together with complementary physicochemical characterization of the grafted species. The ester molecules were chemically grafted to the silica surface and subsequently cleaved into the carboxylic acids. A grafting process of a reproducible monolayer was designed using the reaction of monofunctional organosilane from its gas phase. The thermal deprotection step of the ester end-group was investigated. The thermal deprotection reaction behaves in quite a specific manner when it is conducted at a surface in a grafted layer. Different organosilane molecules terminated by methyl, isopropyl and tert-butyl ester groups were grafted to silica surface; such functionalized materials were characterized by elemental analysis, IR and NMR spectroscopy, and thermogravimetric analysis, and the thermodynamic parameters of the thermal elimination reaction at the surface were measured. The limiting factor of such thermal ester cleavage reaction is the thermal stability of grafted ester group according to the temperature order: tert-butyl groups were not selectively cleaved by temperature. The thermal deprotection of i-propyl ester groups took place at a temperature close to the thermal degradation of the organofunctional tail of the silane. The low thermolysis temperature of the grafted tert-butyl esters allowed their selective cleavage. There is a definite influence of the surface on the reaction. The enthalpy of activation is lower than in the gas phase because of the polarity of the reaction site. The major contribution is entropic; the negative entropy of activation comes from lateral interactions with the neighbor grafted molecules because of the high grafting density. Such reaction is an original strategy to functionalize the silica

  13. Thermal impact of waste emplacement and surface cooling associated with geologic disposal of nuclear waste

    Energy Technology Data Exchange (ETDEWEB)

    Wang, J.S.Y.; Mangold, D.C.; Spencer, R.K.; Tsang, C.F.

    1982-08-01

    The thermal effects associated with the emplacement of aged radioactive wastes in a geologic repository were studied, with emphasis on the following subjects: the waste characteristics, repository structure, and rock properties controlling the thermally induced effects; the current knowledge of the thermal, thermomechanical, and thermohydrologic impacts, determined mainly on the basis of previous studies that assume 10-year-old wastes; the thermal criteria used to determine the repository waste loading densities; and the technical advantages and disadvantages of surface cooling of the wastes prior to disposal as a means of mitigating the thermal impacts. The waste loading densities determined by repository designs for 10-year-old wastes are extended to older wastes using the near-field thermomechanical criteria based on room stability considerations. Also discussed are the effects of long surface cooling periods determined on the basis of far-field thermomechanical and thermohydrologic considerations. The extension of the surface cooling period from 10 years to longer periods can lower the near-field thermal impact but have only modest long-term effects for spent fuel. More significant long-term effects can be achieved by surface cooling of reprocessed high-level waste.

  14. Coupled computational fluid-thermal investigation of hypersonic flow over a quilted dome surface

    Science.gov (United States)

    Ostoich, Christopher; Bodony, Daniel; Geubelle, Philippe

    2009-11-01

    The hypersonic environment is characterized by the high temperatures that are generated in the fluid at a vehicle surface. In the effort to enable the operation of lightweight, reusable hypersonic vehicles, flexible, thin thermal protection panels have been considered to mitigate thermal loads. High surface temperatures create through-the-thickness thermal gradients which cause the panels to bow, resulting in changes to the external flow field and leading to a fully coupled fluid-thermal-structural problem. Certain aspects of the fluid-thermal (no structural) coupling were examined in a 1980s NASA Langley experiment of a Mach 5.74 laminar boundary past an array of spherical domes. We reexamine this case computationally using a high-fidelity Navier-Stokes solver coupled with a thermal solver to investigate the effects on the flow and resulting heat load on the structure due to the bowed panels. Specifically the surface temperature, surface heat flux, and downstream boundary developments are reported, and compared with experiment.

  15. Application of thermal analysis techniques in activated carbon production

    Science.gov (United States)

    Donnals, G.L.; DeBarr, J.A.; Rostam-Abadi, M.; Lizzio, A.A.; Brady, T.A.

    1996-01-01

    Thermal analysis techniques have been used at the ISGS as an aid in the development and characterization of carbon adsorbents. Promising adsorbents from fly ash, tires, and Illinois coals have been produced for various applications. Process conditions determined in the preparation of gram quantities of carbons were used as guides in the preparation of larger samples. TG techniques developed to characterize the carbon adsorbents included the measurement of the kinetics of SO2 adsorption, the performance of rapid proximate analyses, and the determination of equilibrium methane adsorption capacities. Thermal regeneration of carbons was assessed by TG to predict the life cycle of carbon adsorbents in different applications. TPD was used to determine the nature of surface functional groups and their effect on a carbon's adsorption properties.

  16. [Study on Hollow Brick Wall's Surface Temperature with Infrared Thermal Imaging Method].

    Science.gov (United States)

    Tang, Ming-fang; Yin, Yi-hua

    2015-05-01

    To address the characteristic of uneven surface temperature of hollow brick wall, the present research adopts soft wares of both ThermaCAM P20 and ThermaCAM Reporter to test the application of infrared thermal image technique in measuring surface temperature of hollow brick wall, and further analyzes the thermal characteristics of hollow brick wall, and building material's impact on surface temperature distribution including hollow brick, masonry mortar, and so on. The research selects the construction site of a three-story-high residential, carries out the heat transfer experiment, and further examines the exterior wall constructed by 3 different hollow bricks including sintering shale hollow brick, masonry mortar and brick masonry. Infrared thermal image maps are collected, including 3 kinds of sintering shale hollow brick walls under indoor heating in winter; and temperature data of wall surface, and uniformity and frequency distribution are also collected for comparative analysis between 2 hollow bricks and 2 kinds of mortar masonry. The results show that improving heat preservation of hollow brick aid masonry mortar can effectively improve inner wall surface temperature and indoor thermal environment; non-uniformity of surface temperature decreases from 0. 6 to 0. 4 °C , and surface temperature frequency distribution changes from the asymmetric distribution into a normal distribution under the condition that energy-saving sintering shale hollow brick wall is constructed by thermal mortar replacing cement mortar masonry; frequency of average temperature increases as uniformity of surface temperature increases. This research provides a certain basis for promotion and optimization of hollow brick wall's thermal function.

  17. Reduced near-surface thermal inversions in 2005-06 in the southeastern Arabian Sea (Lakshadweep Sea)

    Digital Repository Service at National Institute of Oceanography (India)

    Nisha, K.; Rao, S.A.; Gopalakrishna, V.V.; Rao, R.R.; GirishKumar, M.S.; Pankajakshan, T.; Ravichandran, M.; Rajesh, S.; Girish, K.; Johnson, Z.; Anuradha, M.; Gavaskar, S.S.M.; Suneel, V.; Krishna, S.M.

    relatively cooler near-surface thermal regime persisted owing to prolonged upwelling until November 2005. In addition, the observed local surface wind field was relatively stronger, and the net surface heat gain to the ocean was weaker over the Lakshadweep...

  18. Variation with thermal cycling in microstructure and area specific resistance of a ferritic stainless steel having rough surfaces

    Science.gov (United States)

    Song, Myoung Youp; Mumm, Daniel R.; Song, Jiunn

    2013-03-01

    Crofer22 APU specimens were prepared by grinding with grit 120 and 400 SiC grinding papers, and were then thermally cycled. The variation in oxidation behavior with thermal cycling was then investigated. Observation of microstructures, measurement of area-specific resistance (ASR), analysis of the atomic percentages of the elements by EDX, and XRD analysis were performed. XRD patterns showed that the (Cr, Mn)3O4 spinel phase grew on the surface of the Crofer22 APU samples ground using grit 120. For the samples ground with grit 400, ASR increased as the number of thermal cycles ( n) increased. Plots of ln (ASR/T) vs. 1/ T for the samples ground with grit 400 after n = 4, 20, and 40 exhibited good linearity, and the apparent activation energies were between 73.4 kJ/mole and 82.5 kJ/mole.

  19. Simultaneous inversion of multiple land surface parameters from MODIS optical-thermal observations

    Science.gov (United States)

    Ma, Han; Liang, Shunlin; Xiao, Zhiqiang; Shi, Hanyu

    2017-06-01

    Land surface parameters from remote sensing observations are critical in monitoring and modeling of global climate change and biogeochemical cycles. Current methods for estimating land surface variables usually focus on individual parameters separately even from the same satellite observations, resulting in inconsistent products. Moreover, no efforts have been made to generate global products from integrated observations from the optical to Thermal InfraRed (TIR) spectrum. Particularly, Middle InfraRed (MIR) observations have received little attention due to the complexity of the radiometric signal, which contains both reflected and emitted radiation. In this paper, we propose a unified algorithm for simultaneously retrieving six land surface parameters - Leaf Area Index (LAI), Fraction of Absorbed Photosynthetically Active Radiation (FAPAR), land surface albedo, Land Surface Emissivity (LSE), Land Surface Temperature (LST), and Upwelling Longwave radiation (LWUP) by exploiting MODIS visible-to-TIR observations. We incorporate a unified physical radiative transfer model into a data assimilation framework. The MODIS visible-to-TIR time series datasets include the daily surface reflectance product and MIR-to-TIR surface radiance, which are atmospherically corrected from the MODIS data using the Moderate Resolution Transmittance program (MODTRAN, ver. 5.0). LAI was first estimated using a data assimilation method that combines MODIS daily reflectance data and a LAI phenology model, and then the LAI was input to the unified radiative transfer model to simulate spectral surface reflectance and surface emissivity for calculating surface broadband albedo and emissivity, and FAPAR. LST was estimated from the MIR-TIR surface radiance data and the simulated emissivity, using an iterative optimization procedure. Lastly, LWUP was estimated using the LST and surface emissivity. The retrieved six parameters were extensively validated across six representative sites with

  20. Effect of deformation on the thermal conductivity of granular porous media with rough grain surface

    Science.gov (United States)

    Askari, Roohollah; Hejazi, S. Hossein; Sahimi, Muhammad

    2017-08-01

    Heat transfer in granular porous media is an important phenomenon that is relevant to a wide variety of problems, including geothermal reservoirs and enhanced oil recovery by thermal methods. Resistance to flow of heat in the contact area between the grains strongly influences the effective thermal conductivity of such porous media. Extensive experiments have indicated that the roughness of the grains' surface follows self-affine fractal stochastic functions, and thus, the contact resistance cannot be accounted for by models based on smooth surfaces. Despite the significance of rough contact area, the resistance has been accounted for by a fitting parameter in the models of heat transfer. In this Letter we report on a study of conduction in a packing of particles that contains a fluid of a given conductivity, with each grain having a rough self-affine surface, and is under an external compressive pressure. The deformation of the contact area depends on the fractal dimension that characterizes the grains' rough surface, as well as their Young's modulus. Excellent qualitative agreement is obtained with experimental data. Deformation of granular porous media with grains that have rough self-affine fractal surface is simulated. Thermal contact resistance between grains with rough surfaces is incorporated into the numerical simulation of heat conduction under compressive pressure. By increasing compressive pressure, thermal conductivity is enhanced more in the grains with smoother surfaces and lower Young's modulus. Excellent qualitative agreement is obtained with the experimental data.

  1. Changing the surface properties on naval steel as result of non-thermal plasma treatment

    Science.gov (United States)

    Hnatiuc, B.; Sabău, A.; Dumitrache, C. L.; Hnatiuc, M.; Crețu, M.; Astanei, D.

    2016-08-01

    The problem of corrosion, related to Biofouling formation, is an issue with very high importance in the maritime domain. According to new rules, the paints and all the technologies for the conditioning of naval materials must fulfil more restrictive environmental conditions. In order to solve this issue, different new clean technologies have been proposed. Among them, the use of non-thermal plasmas produced at atmospheric pressure plays a very important role. This study concerns the opportunity of plasma treatment for preparation or conditioning of naval steel OL36 type. The plasma reactors chosen for the experiments can operate at atmospheric pressure and are easy to use in industrial conditions. They are based on electrical discharges GlidArc and Spark, which already proved their efficiency for the surface activation or even for coatings of the surface. The non-thermal character of the plasma is ensured by a gas flow blown through the electrical discharges. One power supply has been used for reactors that provide a 5 kV voltage and a maximum current of 100 mA. The modifications of the surface properties and composition have been studied by XPS technique (X-ray Photoelectron Spectroscopy). There were taken into consideration 5 samples: 4 of them undergoing a Mini-torch plasma, a Gliding Spark, a GlidArc with dry air and a GlidArc with CO2, respectively the fifth sample which is the untreated witness. Before the plasma treatment, samples of naval steel were processed in order to obtain mechanical gloss. The time of treatment was chosen to 12 minutes. In the spectroscopic analysis, done on a ULVAC-PHI, Inc. PHI 5000 Versa Probe scanning XPS microprobe, a monocromated Al Kα X-ray source with a spot size of 100 μm2 was used to scan each sample while the photoelectrons were collected at a 45-degree take-off angle. Differences were found between atomic concentrations in each individual case, which proves that the active species produced by each type of plasma affects

  2. Thermal activation of dislocations in large scale obstacle bypass

    Science.gov (United States)

    Sobie, Cameron; Capolungo, Laurent; McDowell, David L.; Martinez, Enrique

    2017-08-01

    Dislocation dynamics simulations have been used extensively to predict hardening caused by dislocation-obstacle interactions, including irradiation defect hardening in the athermal case. Incorporating the role of thermal energy on these interactions is possible with a framework provided by harmonic transition state theory (HTST) enabling direct access to thermally activated reaction rates using the Arrhenius equation, including rates of dislocation-obstacle bypass processes. Moving beyond unit dislocation-defect reactions to a representative environment containing a large number of defects requires coarse-graining the activation energy barriers of a population of obstacles into an effective energy barrier that accurately represents the large scale collective process. The work presented here investigates the relationship between unit dislocation-defect bypass processes and the distribution of activation energy barriers calculated for ensemble bypass processes. A significant difference between these cases is observed, which is attributed to the inherent cooperative nature of dislocation bypass processes. In addition to the dislocation-defect interaction, the morphology of the dislocation segments pinned to the defects play an important role on the activation energies for bypass. A phenomenological model for activation energy stress dependence is shown to describe well the effect of a distribution of activation energies, and a probabilistic activation energy model incorporating the stress distribution in a material is presented.

  3. The Surface Roughness of (433) Eros as Measured by Thermal-Infrared Beaming

    CERN Document Server

    Rozitis, Ben

    2016-01-01

    In planetary science, surface roughness is regarded to be a measure of surface irregularity at small spatial scales, and causes the thermal-infrared beaming effect (i.e. re-radiation of absorbed sunlight back towards to the Sun). Typically, surface roughness exhibits a degeneracy with thermal inertia when thermophysical models are fitted to disc-integrated thermal-infrared observations of asteroids because of this effect. In this work, it is demonstrated how surface roughness can be constrained for near-Earth asteroid (433) Eros (i.e. the target of NASA's NEAR Shoemaker mission) when using the Advanced Thermophysical Model with thermal-infrared observations taken during an "almost pole-on" illumination and viewing geometry. It is found that the surface roughness of (433) Eros is characterised by an RMS slope of 38 $\\pm$ 8{\\deg} at the 0.5-cm spatial scale associated with its thermal-infrared beaming effect. This is slightly greater than the RMS slope of 25 $\\pm$ 5{\\deg} implied by the NEAR Shoemaker laser ran...

  4. Active surfaces: Ferrofluid-impregnated surfaces for active manipulation of droplets

    Science.gov (United States)

    Khalil, Karim; Mahmoudi, Seyed Reza; Abu-Dheir, Numan; Varanasi, Kripa

    2014-11-01

    Droplet manipulation and mobility on non-wetting surfaces is of practical importance for diverse applications ranging from micro-fluidic devices, anti-icing, dropwise condensation, and biomedical devices. The use of active external fields has been explored via electric, acoustic, and vibrational, yet moving highly conductive and viscous fluids remains a challenge. Magnetic fields have been used for droplet manipulation; however, usually, the fluid is functionalized to be magnetic, and requires enormous fields of superconducting magnets when transitioning to diamagnetic materials such as water. Here we present a class of active surfaces by stably impregnating active fluids such as ferrofluids into a textured surface. Droplets on such ferrofluid-impregnated surfaces have extremely low hysteresis and high mobility such that they can be propelled by applying relatively low magnetic fields. Our surface is able to manipulate a variety of materials including diamagnetic, conductive and highly viscous fluids, and additionally solid particles.

  5. Modeling the surface stored thermal energy in asphalt concrete pavements

    Directory of Open Access Journals (Sweden)

    Matić Bojan J.

    2016-01-01

    Full Text Available Regression analysis is used to develop models for minimal daily pavement surface temperature, using minimal daily air temperature, day of the year, wind speed and solar radiation as predictors, based on data from Awbari, Lybia,. Results were compared with existing SHRP and LTPP models. This paper also presents the models to predict surface pavement temperature depending on the days of the year using neural networks. Four annual periods are defined and new models are formulated for each period. Models using neural networks are formed on the basis of data gathered on the territory of the Republic of Serbia and are valid for that territory. [Projekat Ministarstva nauke Republike Srbije, br. TR 36017

  6. Platelet surface glutathione reductase-like activity.

    Science.gov (United States)

    Essex, David W; Li, Mengru; Feinman, Richard D; Miller, Anna

    2004-09-01

    We previously found that reduced glutathione (GSH) or a mixture of GSH/glutathione disulfide (GSSG) potentiated platelet aggregation. We here report that GSSG, when added to platelets alone, also potentiates platelet aggregation. Most of the GSSG was converted to GSH by a flavoprotein-dependent platelet surface mechanism. This provided an appropriate redox potential for platelet activation. The addition of GSSG to platelets generated sulfhydryls in the beta subunit of the alpha(IIb)beta(3) fibrinogen receptor, suggesting a mechanism for facilitation of agonist-induced platelet activation.

  7. Radar, visual and thermal characteristics of Mars - Rough planar surfaces

    Science.gov (United States)

    Schaber, G. G.

    1980-05-01

    High-resolution Viking Orbiter images contain significant information on Martian surface roughness at 25- to 100-m lateral scales, while earth-based radar observations of Mars are sensitive to roughness at lateral scales of 1 to 30 m or more. High-rms slopes predicted for the Tharsis-Memnonia-Amazonis volcanic plains from extremely weak radar returns are qualitatively confirmed by the Viking image data. Large-scale, curvilinear ridges on lava flows in the Memnonia Fossae region are interpreted as innate flow morphology caused by compressional foldover of moving lava sheets of possible rhyolite-dacite composition. The presence or absence of a recent mantle of fine-grained eolian material on the volcanic surfaces studied was determined by the visibility of fresh impact craters with diameters less than 50 m. Lava flows with surfaces modified by eolian erosion and deposition occur west-northwest of Apollinaris Patera at the border of the cratered equatorial uplands and southern Elysium Planitia. Nearby yardangs, for which radar observations indicate very high-rms slopes, are similar to terrestrial features of similar origin.

  8. Thermal Conductance of a Surface Phonon-Polariton Crystal Made up of Polar Nanorods

    Science.gov (United States)

    Ordonez-Miranda, Jose; Joulain, Karl; Ezzahri, Younes

    2017-02-01

    We demonstrate that the energy transport of surface phonon-polaritons can be large enough to be observable in a crystal made up of a three-dimensional assembly of nanorods of silicon carbide. The ultralow phonon thermal conductivity of this nanostructure along with its high surface area-to-volume ratio allows the predominance of the polariton energy over that generated by phonons. The dispersion relation, propagation length, and thermal conductance of polaritons are numerically determined as functions of the radius and temperature of the nanorods. It is shown that the thermal conductance of a crystal with nanorods at 500 K and diameter (length) of 200 nm (20 μm) is 0.55 nW·K-1, which is comparable to the quantum of thermal conductance of polar nanowires.

  9. Analytical prediction of sub surface thermal history in translucent tissue phantoms during plasmonic photo thermotherapy

    CERN Document Server

    Dhar, Purbarun; Narasimhan, Arunn; Das, Sarit K

    2015-01-01

    Knowledge of thermal history in biological tissues during laser based hyperthermia is essential to achieve necrosis of tumour orcarcinoma cells. A semi analytical model to predict sub surface thermal history in translucent, soft, bio tissue mimics has been proposed. The model can accurately predict the spatio temporal temperature variations along depth and the anomalous thermal behaviour in such media, viz. occurrence of sub surface temperature peaks. Based on opto thermal properties, the augmented temperature and shift of the peak positions in case of gold nanostructure mediated tissue phantom hyperthermia can be predicted. Employing inverse approach, the absorbance coefficient of nano graphene infused tissue mimics is determined from the peak temperature and found to provide appreciably accurate predictions along depth. Furthermore, a simplistic, dimensionally consistent correlation to theoretically determine the position of the peak in such media is proposed and found to be consistent with experiments and ...

  10. Robust and thermal-healing superhydrophobic surfaces by spin-coating of polydimethylsiloxane.

    Science.gov (United States)

    Long, Mengying; Peng, Shan; Deng, Wanshun; Yang, Xiaojun; Miao, Kai; Wen, Ni; Miao, Xinrui; Deng, Wenli

    2017-12-15

    Superhydrophobic surfaces easily lose their excellent water-repellency after damages, which limit their broad applications in practice. Thus, the fabrication of superhydrophobic surfaces with excellent durability and thermal healing should be taken into consideration. In this work, robust superhydrophobic surfaces with thermal healing were successfully fabricated by spin-coating method. To achieve superhydrophobicity, cost-less and fluoride-free polydimethylsiloxane (PDMS) was spin-coated on rough aluminum substrates. After being spin-coated for one cycle, the superhydrophobic PDMS coated hierarchical aluminum (PDMS-H-Al) surfaces showed excellent tolerance to various chemical and mechanical damages in lab, and outdoor damages for 90days. When the PDMS-H-Al surfaces underwent severe damages such as oil contamination (peanut oil with high boiling point) or sandpaper abrasion (500g of force for 60cm), their superhydrophobicity would lose. Interestingly, through a heating process, cyclic oligomers generating from the partially decomposed PDMS acted as low-surface-energy substance on the damaged rough surfaces, leading to the recovery of superhydrophobicity. The relationship between the spin-coating cycles and surface wettability was also investigated. This paper provides a facile, fluoride-free and efficient method to fabricate superhydrophobic surfaces with thermal healing. Copyright © 2017. Published by Elsevier Inc.

  11. Numerical Study of Thermal Boundary Layer on a Continuous Moving Surface in Power Law Fluids

    Institute of Scientific and Technical Information of China (English)

    Hao ZHANG; Xinxin ZHANG; Liancun ZHENG

    2007-01-01

    This paper investigates flow and heat transfer of power law fluids on a continuous moving surface. The temperature distribution is obtained numerically by considering the effect of the power law viscosity on thermal diffusivity and the characteristics of the flow and heat transfer are analyzed. The results show that the distribution of the thermal boundary layer depends not only on the velocity ratio parameter of the plate, but also on the power law index and Prandtl number of fluids.

  12. Thermoregulation and heat exchange in a nonuniform thermal environment during simulated extended EVA. Extravehicular activities

    Science.gov (United States)

    Koscheyev, V. S.; Leon, G. R.; Hubel, A.; Nelson, E. D.; Tranchida, D.

    2000-01-01

    BACKGROUND: Nonuniform heating and cooling of the body, a possibility during extended duration extravehicular activities (EVA), was studied by means of a specially designed water circulating garment that independently heated or cooled the right and left sides of the body. The purpose was to assess whether there was a generalized reaction on the finger in extreme contradictory temperatures on the body surface, as a potential heat status controller. METHOD: Eight subjects, six men and two women, were studied while wearing a sagittally divided experimental garment with hands exposed in the following conditions: Stage 1 baseline--total body garment inlet water temperature at 33 degrees C; Stage 2--left side inlet water temperature heated to 45 degrees C; right side cooled to 8 degrees C; Stage 3--left side inlet water temperature cooled to 8 degrees C, right side heated to 45 degrees C. RESULTS: Temperatures on each side of the body surface as well as ear canal temperature (Tec) showed statistically significant Stage x Side interactions, demonstrating responsiveness to the thermal manipulations. Right and left finger temperatures (Tfing) were not significantly different across stages; their dynamic across time was similar. Rectal temperature (Tre) was not reactive to prevailing cold on the body surface, and therefore not informative. Subjective perception of heat and cold on the left and right sides of the body was consistent with actual temperature manipulations. CONCLUSIONS: Tec and Tre estimates of internal temperature do not provide accurate data for evaluating overall thermal status in nonuniform thermal conditions on the body surface. The use of Tfing has significant potential in providing more accurate information on thermal status and as a feedback method for more precise thermal regulation of the astronaut within the EVA space suit.

  13. Assessing thermal conductivity of composting reactor with attention on varying thermal resistance between compost and the inner surface.

    Science.gov (United States)

    Wang, Yongjiang; Niu, Wenjuan; Ai, Ping

    2016-12-01

    Dynamic estimation of heat transfer through composting reactor wall was crucial for insulating design and maintaining a sanitary temperature. A model, incorporating conductive, convective and radiative heat transfer mechanisms, was developed in this paper to provide thermal resistance calculations for composting reactor wall. The mechanism of thermal transfer from compost to inner surface of structural layer, as a first step of heat loss, was important for improving insulation performance, which was divided into conduction and convection and discussed specifically in this study. It was found decreasing conductive resistance was responsible for the drop of insulation between compost and reactor wall. Increasing compost porosity or manufacturing a curved surface, decreasing the contact area of compost and the reactor wall, might improve the insulation performance. Upon modeling of heat transfers from compost to ambient environment, the study yielded a condensed and simplified model that could be used to conduct thermal resistance analysis for composting reactor. With theoretical derivations and a case application, the model was applicable for both dynamic estimation and typical composting scenario. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Periodic changes in shallow lunat crust caused by Sun's heating and thermal diffusivity near the surface

    Science.gov (United States)

    Tanimoto, T.; Eitzel, M.; Yano, T.

    2007-12-01

    Analysis of Apollo 17 data (continuous data from 1976 to 1977) by the cross-correlation approach for seismic noise led us to two new discoveries, one related to the source of noise and the other on the periodic changes in seismic parameters due to extreme temperature changes near the surface. It has been shown previously by Larose et al. (2005) that Green's functions, dominated by Rayleigh waves, can be retrieved from cross-correlation of seismic noise in Apollo 17 data. We first confirmed their correlation results and further analyzed the details in GreenA?"qfs functions. The first discovery is that the sources of noise that lead to construction of Green's functions are (most likely) thermal moonquakes. This is suggested in the Rayleigh-wave observations that show diurnal variation (29.5 days) in amplitudes, but one can directly confirm a correlation between the statistics of thermal moonquakes and Rayleigh wave amplitudes. This is in contrast to the terrestrial case where ocean-generated seismic noise plays a critical role in the cross-correlation approach. This has implications for future planetary seismology as many planets lack oceans but may have thermal quakes caused by drastic temperature changes near the surface. Second, diurnal temporal variations in group velocity are detected, showing a strong correlation with the temporal variation of lunar surface temperature. This can be explained by the Sun's thermal effects which cause changes in density and seismic velocities near the surface. These effects are measurable on the moon since surface temperature changes as much as 270 K within the diurnal period. Depending on the thermal diffusivity of the medium, the depth extent of this thermal effect varies considerably. Inversion for thermal diffusivity using the changes in group velocity dispersion resulted in an estimate 10**(-7) (m**2/s) for the upper few meters.

  15. Integrated surface/subsurface permafrost thermal hydrology: Model formulation and proof-of-concept simulations

    Science.gov (United States)

    Painter, Scott L.; Coon, Ethan T.; Atchley, Adam L.; Berndt, Markus; Garimella, Rao; Moulton, J. David; Svyatskiy, Daniil; Wilson, Cathy J.

    2016-08-01

    The need to understand potential climate impacts and feedbacks in Arctic regions has prompted recent interest in modeling of permafrost dynamics in a warming climate. A new fine-scale integrated surface/subsurface thermal hydrology modeling capability is described and demonstrated in proof-of-concept simulations. The new modeling capability combines a surface energy balance model with recently developed three-dimensional subsurface thermal hydrology models and new models for nonisothermal surface water flows and snow distribution in the microtopography. Surface water flows are modeled using the diffusion wave equation extended to include energy transport and phase change of ponded water. Variation of snow depth in the microtopography, physically the result of wind scour, is modeled phenomenologically with a diffusion wave equation. The multiple surface and subsurface processes are implemented by leveraging highly parallel community software. Fully integrated thermal hydrology simulations on the tilted open book catchment, an important test case for integrated surface/subsurface flow modeling, are presented. Fine-scale 100 year projections of the integrated permafrost thermal hydrological system on an ice wedge polygon at Barrow Alaska in a warming climate are also presented. These simulations demonstrate the feasibility of microtopography-resolving, process-rich simulations as a tool to help understand possible future evolution of the carbon-rich Arctic tundra in a warming climate.

  16. Measuring thermal budgets of active volcanoes by satellite remote sensing

    Science.gov (United States)

    Glaze, L.; Francis, P. W.; Rothery, D. A.

    1989-01-01

    Thematic Mapper measurements of the total radiant energy flux Q at Lascar volcano in north Chile for December 1984 are reported. The results are consistent with the earlier suggestion that a lava lake is the source of a reported thermal budget anomaly, and with values for 1985-1986 that are much lower, suggesting that fumarolic activity was then a more likely heat source. The results show that satellite remote sensing may be used to monitor the activity of a volcano quantitatively, in a way not possible by conventional ground studies, and may provide a method for predicting eruptions.

  17. New perspectives on thermal and hyperthermal oxidation of silicon surfaces

    Science.gov (United States)

    Khalilov, Umedjon

    The growth of (ultra)thin silica (SiO2) layers on crystalline silicon (c-Si) and controlling the thickness of SiO2 is an important issue in the fabrication of microelectronics and photovoltaic devices (e.g., MOSFETs, solar cells, optical fibers etc.). Such ultrathin oxide can be grown and tuned even at low temperature (including room temperature), by hyperthermal oxidation or when performed on non-planar Si surfaces (e.g., Si nanowires or spheres). However, hyperthermal silica growth as well as small Si-NW oxidation in general and the initial stages in particular have not yet been investigated in full detail. This work is therefore devoted to controlling ultrathin silica thickness on planar and non-planar Si surfaces, which can open new perspectives in nanodevice fabrication. The simulation of hyperthermal (1-100 eV) Si oxidation demonstrate that at low impact energy (nanotechnology. Above the transition temperature such core-shell nanowires are completely converted to a-SiO2 nanowires. It can be concluded that an accurate control over the interfacial stress by choosing a suitable oxidation temperature and Si-NW diameter can lead to precise nanoscale control over the Si-core radius. All investigations were carried out by applying molecular dynamics calculations using the ReaxFF potential, allowing a accurately study of the underpinning physical and chemical processes.

  18. Compositional variability across Mercury's surface revealed by MESSENGER measurements of variations in thermal neutron count rates

    Science.gov (United States)

    Peplowski, P. N.; Lawrence, D. J.; Goldsten, J. O.; Nittler, L. R.; Solomon, S. C.

    2013-12-01

    Measurements by MESSENGER's Gamma-Ray and Neutron Spectrometer (GRNS) have revealed variations in the flux of thermal neutrons across Mercury's northern hemisphere. These variations are interpreted to originate from spatial variations in surface elemental composition. In particular, the measurements are sensitive to the near-surface abundances of elements that absorb thermal neutrons, including major rock-forming elements such as Fe and Ti, minor elements such as Mn and Cl, and rare-earth elements such as Gd and Sm. We have constructed a map of thermal neutron variability across the surface and compared it with known variations in elemental composition and with the distribution of geologic units. Development of the map included the derivation of the macroscopic thermal neutron absorption cross section across the surface, a quantity whose value and variability provides useful constraints on the formation and geochemical evolution of Mercury's crust. Finally, by combining the thermal neutron measurements with previously reported elemental measurements from the GRNS and MESSENGER's X-Ray Spectrometer, we have derived constraints on the abundances of neutron-absorbing elements, including previously unreported limits for some minor and rare-earth elements.

  19. Size Scaling and Bursting Activity in Thermally Activated Breakdown of Fiber Bundles

    KAUST Repository

    Yoshioka, Naoki

    2008-10-03

    We study subcritical fracture driven by thermally activated damage accumulation in the framework of fiber bundle models. We show that in the presence of stress inhomogeneities, thermally activated cracking results in an anomalous size effect; i.e., the average lifetime tf decreases as a power law of the system size tf ∼L-z, where the exponent z depends on the external load σ and on the temperature T in the form z∼f(σ/T3/2). We propose a modified form of the Arrhenius law which provides a comprehensive description of thermally activated breakdown. Thermal fluctuations trigger bursts of breakings which have a power law size distribution. © 2008 The American Physical Society.

  20. Wear measurement by surface layer activation

    Energy Technology Data Exchange (ETDEWEB)

    Blatchley, C.

    1987-05-01

    The purpose of these projects was to demonstrate the capability for precisely but remotely measuring small increments of wear, erosion or corrosion in utility components using detectors mounted outside the system to monitor the presence of radionuclide surface markers. These gamma ray emitting markers are produced by surface layer activation (SLA) using a high energy particle beam from a Van de Graaff or cyclotron particle accelerator. The work was divided into three major projects: (1) determination of the feasibility of applying SLA based surface monitoring techniques to key power plant systems; (2) a field demonstration of SLA monitoring in steam turbine components subject to severe solid particle erosion; and (3) a field demonstration of SLA wear or corrosion monitoring of components in boiler auxiliaries. In the field tests, surface material removal was successfully measured from both selected systems, demonstrating the feasibility of the technique for long term diagnostic condition monitoring. Three bearing components in a boiler circulation pump were monitored almost continuously for a period of over 5 months until the pump was stopped due to electrical problems unrelated to the wear measurements. Solid particle erosion from two stop valve bypass valves was measured during a series of nine startup cycles. Both test demonstrations confirmed the earlier feasibility estimates and showed how SLA markers can be used to provide valuable diagnostic information to plant operators. 22 refs., 63 figs., 29 tabs.

  1. The influence of the base material surface preparation on the properties of thermally sprayed coatings

    Directory of Open Access Journals (Sweden)

    V. Marušić

    2010-01-01

    Full Text Available Using specimens, a research was conducted to determine the influence of the base material surface preparation for 42CrMo4 on the final coating, prior to actual thermal spraying. During thermal spraying, an Al-Ni-alloy was used as an interlayer before the actual coating with Cr-Mo-Ni. The surface hardness and the hardness distribution across the thickness of the sprayed coating were measured and the structure of respective sprayed coatings was photographed. A comparison of experimental results enabled the identification of the particular material preparation method with an optimal ratio of the satisfactory coating thickness and its hardness.

  2. Pathogenic and nonpathogenic Acanthamoeba spp. in thermally polluted discharges and surface waters

    Energy Technology Data Exchange (ETDEWEB)

    de Jonckheere, J.F.

    1981-02-01

    During spring and autumn, the total number of amoebae and the number of acanthamoeba species able to grow at 37 degrees C were determined in six thermally polluted factory discharges and the surrounding surface waters. The isolated Acanthamoeba strains were studied for growth in axenic medium, cytopathic effect in Vito cell cultures, and virulence in mice. Although more amoebae were isolated in autumn, the number of Acanthamoeba species was lower than in spring, when the percent of pathogenic strains among the isolates was highest. Higher concentrations of amoebae were found in warm discharges, and more virulent strains occurred in thermal discharges than in surface waters.

  3. [The surface degradation of various light-cured composite resins by thermal cycling].

    Science.gov (United States)

    Hirabayashi, S; Nomoto, R; Harashima, I; Hirasawa, T

    1990-01-01

    The durability of four commercially available light-cured composite resins was investigated by thermal cycling, GR containing inorganic fillers treated with the graft polymerization of acryl ester, LF inorganic fillers treated with a silane coupling agent, PC silanized inorganic fillers and organic composite fillers, and the MFR-type SI containing the organic composite fillers. These materials were given 10,000, 30,000 and 50,000 thermal cycles (4 degrees C-60 degrees C) and the deterioration of materials by thermal cycling was evaluated by the measurement of the mechanical properties and the SEM observations of the surface of the thermocycled materials. Compressive strength and bending elastic moduli for all materials did not change greatly by thermal cycling. However, bending strength, toothbrush abrasion resistance and surface hardness decreased with increasing number of thermal cycles between 0 and 30,000, and changed little after 30,000 cycles. The percentage of bending strength after 50,000 thermal cycles to that of the non-thermocycled sample was 75% for GR, 60% for LF, 50% for PC and 65% for SI, respectively. Deterioration of materials was observed as cracks on the surface, which generated at the interface of the filler and matrix. The cracks generated relatively earlier during thermal cycling for SI and PC which contained the organic composite filler, later for LF which contained the silanized inorganic fillers, and the number of cracks on LF were fewer than SI and PC. On the other hand, for GR, no cracks were observed even after 50,000 thermal cycles. From these results, it can be presumed that the pre-treatment of filler by the graft polymerization is more effective to improve the durability of composite resin.

  4. Thermally activated retainer means utilizing shape memory alloy

    Science.gov (United States)

    Grimaldi, Margaret E. (Inventor); Hartz, Leslie S. (Inventor)

    1993-01-01

    A retainer member suitable for retaining a gap filler placed in gaps between adjacent tile members is presented. One edge of the retainer member may be attached to the gap filler and another edge may be provided with a plurality of tab members which in an intermediate position do not interfere with placement or removal of the gap filler between tile members. The retainer member may be fabricated from a shape memory alloy which when heated to a specified memory temperature will thermally activate the tab members to predetermined memory positions engaging the tile members to retain the gap filler in the gap. This invention has particular application to the thermal tiles on space vehicles such as the Space Shuttle Orbiter.

  5. Thermal and hydrodynamic modelling of active catheters for interventional radiology.

    Science.gov (United States)

    Marchandise, Emilie; Flaud, Patrice; Royon, Laurent; Blanc, Raphaël; Szewczyk, Jérome

    2011-07-01

    Interventional radiologists desire to improve their operating tools such as catheters. Active catheters in which the tip is moved using shape memory alloy actuators activated using the Joule effect present a promising approach for easier navigation in the small vessels. However, the increase in temperature caused by this Joule effect must be controlled in order to prevent damage to blood cells and tissues. This paper is devoted to the simulation and experimental validation of a fluid-thermal model of an active catheter prototype. Comparisons between computer-predicted and experimentally measured temperatures are presented for both experiments in air and water at 37°C. Good agreement between the computational and experimental results is found, demonstrating the validity of the developed computer model. These comparisons enable us to highlight some important issues in the modelling process and to determine the optimal current for the activation of the catheter.

  6. Detectability of thermal signatures associated with active formation of ‘chaos terrain’ on Europa

    Science.gov (United States)

    Abramov, Oleg; Rathbun, J.; Schmidt, Britney E.; Spencer, John R.

    2013-01-01

    A recent study by Schmidt et al. (2011) suggests that Thera Macula, one of the “chaos regions” on Europa, may be actively forming over a large liquid water lens. Such a process could conceivably produce a thermal anomaly detectable by a future Europa orbiter or flyby mission, allowing for a direct verification of this finding. Here, we present a set of models that quantitatively assess the surface and subsurface temperatures associated with an actively resurfacing chaos region using constraints from Thera Macula. The results of this numerical study suggest that the surface temperature over an active chaos region can be as high as ∼200 K. However, low-resolution Galileo Photo-Polarimeter Radiometer (PPR) observations indicate temperatures below 120 K over Thera Macula. This suggests that Thera Macula is not currently active unless an insulating layer of at least a few centimeters in thickness is present, or activity is confined to small regions, reducing the overall intensity of the thermal signature. Alternatively, Thera may have been cooling for at least 10–100 yr and still contain a subsurface lake, which can take ∼300,000 yr to crystallize. According to the present study, a more sensitive instrument capable of detecting anomalies ∼5 K above ambient could detect activity at Thera Macula even if an insulating layer of ∼50 cm is present.

  7. Influence of surface scattering on the thermal properties of spatially confined GaN nanofilm

    Science.gov (United States)

    Hou, Yang; Zhu, Lin-Li

    2016-08-01

    Gallium nitride (GaN), the notable representative of third generation semiconductors, has been widely applied to optoelectronic and microelectronic devices due to its excellent physical and chemical properties. In this paper, we investigate the surface scattering effect on the thermal properties of GaN nanofilms. The contribution of surface scattering to phonon transport is involved in solving a Boltzmann transport equation (BTE). The confined phonon properties of GaN nanofilms are calculated based on the elastic model. The theoretical results show that the surface scattering effect can modify the cross-plane phonon thermal conductivity of GaN nanostructures completely, resulting in the significant change of size effect on the conductivity in GaN nanofilm. Compared with the quantum confinement effect, the surface scattering leads to the order-of-magnitude reduction of the cross-plane thermal conductivity in GaN nanofilm. This work could be helpful for controlling the thermal properties of GaN nanostructures in nanoelectronic devices through surface engineering. Project supported by the National Natural Science Foundation of China (Grant Nos. 11302189 and 11321202) and the Doctoral Fund of Ministry of Education of China (Grant No. 20130101120175).

  8. Physicochemical and porosity characteristics of thermally regenerated activated carbon polluted with biological activated carbon process.

    Science.gov (United States)

    Dong, Lihua; Liu, Wenjun; Jiang, Renfu; Wang, Zhansheng

    2014-11-01

    The characteristics of thermally regenerated activated carbon (AC) polluted with biological activated carbon (BAC) process were investigated. The results showed that the true micropore and sub-micropore volume, pH value, bulk density, and hardness of regenerated AC decreased compared to the virgin AC, but the total pore volume increased. XPS analysis displayed that the ash contents of Al, Si, and Ca in the regenerated AC respectively increased by 3.83%, 2.62% and 1.8%. FTIR spectrum showed that the surface functional groups of virgin and regenerated AC did not change significantly. Pore size distributions indicated that the AC regeneration process resulted in the decrease of micropore and macropore (D>10 μm) volume and the increase of mesopore and macropore (0.1 μm

  9. Corrosion and biofouling on the non-heat-exchanger surfaces of an ocean thermal energy conversion power plant: a survey

    Energy Technology Data Exchange (ETDEWEB)

    Castelli, V.J. (ed.)

    1979-05-01

    Of the many foreseeable problems confronting economical ocean thermal energy conversion operation, two major items are the deterioration of the structural and functional components, which prevents efficient operation, and the biofouling of the surfaces, which adds excess weight to the floating ocean platform. The techniques required for effective long-term control of deterioration and corrosion have been investigated actively for many years, and successful solutions for most situations have been developed. For the most part, these solutions can be directly transferred to the ocean thermal energy conversion plant. The majority of problems in these areas are expected to be associated with scale-up and will require some advanced development due to the immensity of the ocean thermal energy conversion platform. Current antifouling control systems are not effective for long-term fouling prevention. Commercially available antifouling coatings are limited to a 3-year service life in temperate waters, and even shorter in tropical waters. However, underwater cleaning techniques and some fouling-control systems presently being used by conventional power plants may find utility on an ocean thermal energy conversion plant. In addition, some recent major advances in long-term antifouling coatings sponsored by the Navy may be applicable to ocean thermal energy conversion. 132 references.

  10. Experimental investigation on the thermal performance of heat storage walls coupled with active solar systems

    Science.gov (United States)

    Zhao, Chunyu; You, Shijun; Zhu, Chunying; Yu, Wei

    2016-12-01

    This paper presents an experimental investigation of the performance of a system combining a low-temperature water wall radiant heating system and phase change energy storage technology with an active solar system. This system uses a thermal storage wall that is designed with multilayer thermal storage plates. The heat storage material is expanded graphite that absorbs a mixture of capric acid and lauric acid. An experiment is performed to study the actual effect. The following are studied under winter conditions: (1) the temperature of the radiation wall surface, (2) the melting status of the thermal storage material in the internal plate, (3) the density of the heat flux, and (4) the temperature distribution of the indoor space. The results reveal that the room temperature is controlled between 16 and 20 °C, and the thermal storage wall meets the heating and temperature requirements. The following are also studied under summer conditions: (1) the internal relationship between the indoor temperature distribution and the heat transfer within the regenerative plates during the day and (2) the relationship between the outlet air temperature and inlet air temperature in the thermal storage wall in cooling mode at night. The results indicate that the indoor temperature is approximately 27 °C, which satisfies the summer air-conditioning requirements.

  11. Mathematical modeling of temperature mapping over skin surface and its implementation in thermal disease diagnostics.

    Science.gov (United States)

    Deng, Zhong-Shan; Liu, Jing

    2004-09-01

    In non-invasive thermal diagnostics, accurate correlations between the thermal image on skin surface and interior human pathophysiology are often desired, which require general solutions for the bioheat equation. In this study, the Monte Carlo method was implemented to solve the transient three-dimensional bio-heat transfer problem with non-linear boundary conditions (simultaneously with convection, radiation and evaporation) and space-dependent thermal physiological parameters. Detailed computations indicated that the thermal states of biological bodies, reflecting physiological conditions, could be correlated to the temperature or heat flux mapping recorded at the skin surface. The effect of the skin emissivity and humidity, the convective heat transfer coefficient, the relative humidity and temperature of the surrounding air, the metabolic rate and blood perfusion rate in the tumor, and the tumor size and number on the sensitivity of thermography are comprehensively investigated. Moreover, several thermal criteria for disease diagnostic were proposed based on statistical principles. Implementations of this study for the clinical thermal diagnostics are discussed.

  12. Thermal Stability of Surface Layer Microstructures of Commercially Pure Titanium Treated by High Energy Shot Peening

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yu-juan; CHEN Chun-huan; REN Rui-ming

    2004-01-01

    Commercially pure titanium was treated by high energy shot peening, and annealed at a series of temperatures. The surface layers are characterized by means of scan electronic microscope, X-Ray diffraction, transmission electronic microscope and micro-hardness testing machine. The results showed that microhardness of surface layers decreases with anneal temperature, the tendency of microhardness is similar to unannealed one, in other words, the more close to the surface, the more rapidly the hardness decreases, after reaches the depth of 50 μm, the decrease becomes steadily. But the sub-surface microhardness decreased suddenly over 500 ℃, From 550 ℃ to 650 ℃, the microhardness of surface layers almost unchanged.Observing by TEM and SEM, the grain sizes of pure titanium surface layers have increased below 500 ℃; Deformation twins begin disappearing obviously at 550 ℃; The nano-scaled grains within about 10 micrometers from surface existed even at 550℃.Surface nanocrystallization is well known as one of important methods to improve surface properties. The thermal stability of nanocrystalline microstructures was related to their preparation and application. The commercial pure Ti thermal stability of nanocrystalline and deformed microstructures induced by high-energy-shot-peening (HESP) technique was investigated. The nanostructured surface and deformed sub-surface layers of specimens were prepared through HESP treatment. The thermal stability was characterized through XRD analyses of surface layers, SEM and TEM microstructure observation and microhardness measurement of specimens annealed in different temperature in the air after HESP treatments. The results showed that after HESP treatment, the microhardness of surface layers increased with treatment time, especially in the rang of about 40 micrometers from the surface, the microhardness increase was obvious. The surface microhardness decreased gradually with annealing temperature, but the sub-surface

  13. The Wear behavior of UHMWPE against Surface Modified CP-Titanium by Thermal Oxidation

    Directory of Open Access Journals (Sweden)

    B.T. Prayoga

    2016-12-01

    Full Text Available The effects of thermal oxidation duration on hardness, roughness, and wettability of the CP-titanium surfaces were investigated in this paper. The thermal oxidation treatment was done at 700 oC for 12-36 hours in an air atmosphere. The wear behavior of the UHMWPE sliding against treated thermal oxidation of the CP-titanium was tested by a pin-on-plate tribometer under lubrication of the solution of 75 % distilled water and 25 % bovine serum. The results showed that the layer of the oxide titanium was formed on the surface after being treated by the thermal oxidation for 12-36 hours. The oxide titanium layer was dominated by rutile form of TiO2, that offers an improvement of hardness and wettability of the CP-titanium surfaces. The average wear factor of the UHMWPE reduced significantly when the sliding against of the CP-titanium was modified by the thermal oxidation, and the lowest average wear factor was reached when the sliding against the 12 hour oxidized CP-titanium counterfaces.

  14. Surface modification of cellulose acetate membrane using thermal annealing to enhance produced water treatment

    Energy Technology Data Exchange (ETDEWEB)

    Kusworo, T. D., E-mail: tdkusworo@che.undip.ac.id; Aryanti, N., E-mail: nita.aryanti@gmail.com; Firdaus, M. M. H.; Sukmawati, H. [Chemical Engineering, Faculty of Engineering, Diponegoro University Prof. Soedarto Street, Tembalang, Semarang, 50239, Phone/Fax : (024)7460058 (Indonesia)

    2015-12-29

    This study is performed primarily to investigate the effect of surface modification of cellulose acetate using thermal annealing on the enhancement of membrane performance for produced water treatment. In this study, Cellulose Acetate membranes were casted using dry/wet phase inversion technique. The effect of additive and post-treatment using thermal annealing on the membrane surface were examined for produced water treatment. Therma annealing was subjected to membrane surface at 60 and 70 °C for 5, 10 and 15 second, respectively. Membrane characterizations were done using membrane flux and rejection with produced water as a feed, Scanning Electron Microscopy (SEM) and Fourier Transform Infra Red (FTIR) analysis. Experimental results showed that asymmetric cellulose acetate membrane can be made by dry/wet phase inversion technique. The results from the Scanning Electron Microscopy (FESEM) analysis was also confirmed that polyethylene glycol as additivie in dope solution and thermal annealing was affected the morphology and membrane performance for produced water treatment, respectively. Scanning electron microscopy micrographs showed that the selective layer and the substructure of membrane became denser and more compact after the thermal annealing processes. Therefore, membrane rejection was significantly increased while the flux was slighty decreased, respectively. The best membrane performance is obtained on the composition of 18 wt % cellulose acetate, poly ethylene glycol 5 wt% with thermal annealing at 70° C for 15 second.

  15. Rayleigh surface waves, phonon mode conversion, and thermal transport in nanostructures

    Science.gov (United States)

    Maurer, Leon; Knezevic, Irena

    We study the effects of phonon mode conversion and Rayleigh (surface) waves on thermal transport in nanostructures. We present a technique to calculate thermal conductivity in the elastic-solid approximation: a finite-difference time-domain (FDTD) solution of the elastic or scalar wave equations combined with the Green-Kubo formula. The technique is similar to an equilibrium molecular dynamics simulation, captures phonon wave behavior, and scales well to nanostructures that are too large to simulate with many other techniques. By imposing fixed or free boundary conditions, we can selectively turn off mode conversion and Rayleigh waves to study their effects. In the example case of graphenelike nanoribbons with rough edges, we find that mode conversion among bulk modes has little effect on thermal transport, but that conversion between bulk and Rayleigh waves can significantly reduce thermal conductivity. With increasing surface disorder, Rayleigh waves readily become trapped by the disorder and draw energy away from the propagating bulk modes, which lowers thermal conductivity. We discuss the implications on the accuracy of popular phonon-surface scattering models that stem from scalar wave equations and cannot capture mode conversion to Rayleigh waves.

  16. An efficient plate heater with uniform surface temperature engineered with effective thermal materials

    CERN Document Server

    Liu, Yichao; He, Sailing; Ma, Yungui

    2014-01-01

    Extended from its electromagnetic counterpart, transformation thermodynamics applied to thermal conduction equations can map a virtual geometry into a physical thermal medium, realizing the manipulation of heat flux with almost arbitrarily desired diffusion paths, which provides unprecedented opportunities to create thermal devices unconceivable or deemed impossible before. In this work we employ this technique to design an efficient plate heater that can transiently achieve a large surface of uniform temperature powered by a small thermal source. As opposed to the traditional approach of relying on the deployment of a resistor network, our approach fully takes advantage of an advanced functional material system to guide the heat flux to achieve the desired temperature heating profile. A different set of material parameters for the transformed device has been developed, offering the parametric freedom for practical applications. As a proof of concept, the proposed devices are implemented with engineered therm...

  17. Understanding Thermal Activation Processes in Exchange Bias Systems

    Science.gov (United States)

    O'Grady, Kevin

    2007-03-01

    The phenomenon of exchange bias has been of major scientific interest and technological importance since the 1980s following its discovery by Meiklejohn and Bean in 1956 [1,2]. Following initial seminal work by Fulcomer and Charap [3] it has recently become clear that a major contribution to the phenomena of exchange bias derives from the fact that the grains in the antiferromagnetic (AF) layer are capable of thermally activated reorientation due to the exchange field from the ferromagnetic (F) layer. In this work careful measurement protocols will be presented that enable the thermal activation process to be analysed in considerable detail. More recently Hoffman [4] has described a spin reorientation process that occurs after the AF layer is set which leads to a large shift in the forward going hysteresis loop on the first reversal of the F layer. This effect, coupled to the thermal activation process, gives rise to the phenomenon of training whereby the loop progressively shifts from its original set direction towards the origin. Lastly we have observed a spin freezing phenomena at the interface that can be induced by either temperature or applied field which results in a systematic variation of the exchange bias. We interpret this effect as being due to paramagnetic like spins at the interface whose ordering leads to a significant increase in the overall value of the exchange bias. Thus we show that exchange bias is a complex convolution of at least three distinct effects, all of which will be described in detail. This explains why single theories of how this effect arises have been so unsuccessful during the last 50 years. [1] Meiklejohn and Bean: Physical Review vol.102 p.1413 (1956) [2] Nogues and Schuller: Journal of Magnetism and Magnetic Materials vol.192 p.203 (1999) [3] Fulcomer and Charap: Journal of Applied Physics vol.43 p.4190 (1972) [4] Hoffmann: Physical Review Letters vol.93 p.097203 (2004)

  18. Surface activity of a monoclonal antibody.

    Science.gov (United States)

    Mahler, Hanns-Christian; Senner, Frank; Maeder, Karsten; Mueller, Robert

    2009-12-01

    The development of high concentration antibody formulations presents a major challenge for the formulation scientist, as physical characteristics and stability behavior change compared to low concentration protein formulations. The aim of this study was to investigate the potential correlation between surface activity and shaking stress stability of a model antibody-polysorbate 20 formulation. The surface activities of pure antibody and polysorbate 20 were compared, followed by a study on the influence of a model antibody on the apparent critical micelle concentration (CMC) of polysorbate 20 over a protein concentration range from 10 to 150 mg/mL. In a shaking stress experiment, the stability of 10, 75, and 150 mg/mL antibody formulations was investigated containing different concentrations of polysorbate 20, both below and above the CMC. The antibody increased significantly the apparent CMC of antibody-polysorbate 20 mixtures in comparison to the protein-free buffer. However, the concentration of polysorbate required for stabilization of the model antibody in a shaking stress experiment did not show dependence on the CMC. A polysorbate 20 level of 0.005% was found sufficient to stabilize both at low and high antibody concentration against antibody aggregation and precipitation.

  19. Surface-impedance approach solves problems with the thermal Casimir force between real metals

    CERN Document Server

    Geyer, B; Mostepanenko, V M

    2003-01-01

    The surface impedance approach to the description of the thermal Casimir effect in the case of real metals is elaborated starting from the free energy of oscillators. The Lifshitz formula expressed in terms of the dielectric permittivity depending only on frequency is shown to be inapplicable in the frequency region where a real current may arise leading to Joule heating of the metal. The standard concept of a fluctuating electromagnetic field on such frequencies meets difficulties when used as a model for the zero-point oscillations or thermal photons in the thermal equilibrium inside metals. Instead, the surface impedance permits not to consider the electromagnetic oscillations inside the metal but taking the realistic material properties into account by means of the effective boundary condition. An independent derivation of the Lifshitz-type formulas for the Casimir free energy and force between two metal plates is presented within the impedance approach. It is shown that they are free of the contradiction...

  20. Thermal Advantages for Solar Heating Systems with a Glass Cover with Antireflection Surfaces

    DEFF Research Database (Denmark)

    Furbo, Simon; Shah, Louise Jivan

    2003-01-01

    Investigations elucidate how a glass cover with antireflection surfaces can improve the efficiency of a solar collector and the thermal performance of solar heating systems. The transmittances for two glass covers for a flat-plate solar collector were measured for different incidence angles...... was determined for different solar heating systems. Three systems were investigated: solar domestic hot water systems, solar heating systems for combined space heating demand and domestic hot water supply, and large solar heating plants. The yearly thermal performance of the systems was calculated by detailed...... simulation models with collectors with a normal glass cover and with a glass cover with antireflection surfaces. The calculations were carried out for different solar fractions and temperature levels of the solar heating systems. These parameters influence greatly the thermal performance associated...

  1. Thermal evolution of structure and photocatalytic activity in polymer microsphere templated TiO2 microbowls

    Science.gov (United States)

    Erdogan, Deniz Altunoz; Polat, Meryem; Garifullin, Ruslan; Guler, Mustafa O.; Ozensoy, Emrah

    2014-07-01

    Polystyrene cross-linked divinyl benzene (PS-co-DVB) microspheres were used as an organic template in order to synthesize photocatalytic TiO2 microspheres and microbowls. Photocatalytic activity of the microbowl surfaces were demonstrated both in the gas phase via photocatalytic NO(g) oxidation by O2(g) as well as in the liquid phase via Rhodamine B degradation. Thermal degradation mechanism of the polymer template and its direct influence on the TiO2 crystal structure, surface morphology, composition, specific surface area and the gas/liquid phase photocatalytic activity data were discussed in detail. With increasing calcination temperatures, spherical polymer template first undergoes a glass transition, covering the TiO2 film, followed by the complete decomposition of the organic template to yield TiO2 exposed microbowl structures. TiO2 microbowl systems calcined at 600 °C yielded the highest per-site basis photocatalytic activity. Crystallographic and electronic properties of the TiO2 microsphere surfaces as well as their surface area play a crucial role in their ultimate photocatalytic activity. It was demonstrated that the polymer microsphere templated TiO2 photocatalysts presented in the current work offer a promising and a versatile synthetic platform for photocatalytic DeNOx applications for air purification technologies.

  2. Mobility activation in thermally deposited CdSe thin films

    Indian Academy of Sciences (India)

    Kangkan Sarmah; Ranjan Sarma

    2009-08-01

    Effect of illumination on mobility has been studied from the photocurrent decay characteristics of thermally evaporated CdSe thin films deposited on suitably cleaned glass substrate held at elevated substrate temperatures. The study indicates that the mobilities of the carriers of different trap levels are activated due to the energy of incident illumination, which results in the existence of two distinct trap levels. In each trap depth the energy of the trap increases linearly. It infers that there is a linear distribution of traps of different energies below the conduction band.

  3. Thermal activation in statistical clusters of magnetic nanoparticles

    Science.gov (United States)

    Hovorka, O.

    2017-02-01

    This article presents a kinetic Monte-Carlo study of thermally activated magnetisation dynamics in clusters of statistically distributed magnetic nanoparticles. The structure of clusters is assumed to be of fractal nature, consistently with recent observations of magnetic particle aggregation in cellular environments. The computed magnetisation relaxation decay and frequency-dependent hysteresis loops are seen to significantly depend on the fractal dimension of aggregates, leading to accelerated magnetisation relaxation and reduction in the size of hysteresis loops as the fractal dimension increases from one-dimensional-like to three-dimensional-like clusters. Discussed are implications for applications in nanomedicine, such as magnetic hyperthermia or magnetic particle imaging.

  4. Surface morphology changes of graphene on flexible PET substrate upon thermal annealing.

    Science.gov (United States)

    Samal, Monica; Lee, Jong Min; Park, Won Il; Yi, Dong Kee; Paik, Ungyu; Lee, Chang-Lyoul

    2011-11-01

    The performance of a polymer photovoltaic device using multilayered graphene on an amorphous PET substrate as the electrode was studied. The changes in surface morphology of graphene coated polyethylene terephthalate (PETG) substrate upon thermal annealing were investigated by atomic force microscopy (AFM), field emission scanning electron microscope (FE-SEM) and current-voltage characteristics. The root mean square (RMS) roughness of PETG substrate before annealing was 36.5 nm that decreased to 11.5 nm after 10 min thermal annealing at 110 degrees C. The mean grain size of the substrate decreased from 2301 nm2 to 848 nm2. The PETG surface became smooth when thermally annealed as the voids created by the bubbles in the graphene layer were filled up with thermal expansion of the PET substrate. However, cracks present initially on the graphene due to surface stress between the graphene and PET layer grew further upon annealing that deteriorated the device performance. This study on the graphene surface morphology change upon annealing and the consequent drop in device performance vis-à-vis an ITO glass electrode shows potential drawback of solar cell device fabrication on such flexible substrates.

  5. Estimation of Thermal Contact Conductance between Blank and Tool Surface in Hot Stamping Process

    Science.gov (United States)

    Taha, Zahari; Hanafiah Shaharudin, M. A.

    2016-02-01

    In hot stamping, the determination of the thermal contact conductance values between the blank and tool surface during the process is crucial for the purpose of simulating the blank rapid cooling inside the tool using finite element analysis (FEA). The thermal contact conductance value represents the coefficient of the heat transfer at the surface of two solid bodies in contact and is known to be influenced greatly by the applied pressure. In order to estimate the value and its dependency on applied pressure, the process of hot stamping was replicated and simplified into a process of compression of heated flat blank in between the tool at different applied pressure. The temperature of the blank and tool surface were measured by means of thermocouples installed inside the tool. Based on the measured temperature, the thermal contact conductance between the surfaces was calculated using Newton's cooling law equation. The calculated value was then used to simulate the blank cooling inside the tool using FEA commercial software. This paper describes an experimental approach to estimate the thermal contact conductance between a blank made of Boron Steel (USIBOR 1500) and tool made of Tool Steel (STAVAX). Its dependency on applied pressure is also studied and the experimental results were then compared with FEA simulations.

  6. Thermal and Dynamic Properties of Volcanic Lava Inferred from Measurements on its Surface

    Science.gov (United States)

    Ismail-Zadeh, A.; Korotkii, A.; Kovtunov, D.; Tsepelev, I.; Melnik, O. E.

    2015-12-01

    Modern remote sensing technologies allow for detecting the absolute temperature at the surface of volcanic lava, and the heat flow could be then inferred from the Stefan-Boltzmann law. Is it possible to use these surface thermal data to constrain the thermal and dynamic conditions inside the lava? We propose a quantitative approach to reconstruct temperature and velocity in the steady-state volcanic lava flow from thermal observations at its surface. This problem is reduced to a combination of the direct and inverse problems of mass- and heat transport. Namely, using known conditions at the lava surface we determine the missing condition at the bottom of lava (the inverse problem) and then search for the physical properties of lava - temperature and flow velocity - inside the lava (the direct problem). Assuming that the lava rheology and the thermal conductivity are temperature-dependent, we determine the flow characteristics in the model domain using an adjoint method. We show that in the case of smooth input data (observations) the lava temperature and the flow velocity can be reconstructed with a high accuracy. The noise imposed on the smooth input data results in a less accurate solution, but still acceptable below some noise level.

  7. The Surface-to-Volume Ratio in Thermal Physics: From Cheese Cube Physics to Animal Metabolism

    Science.gov (United States)

    Planinsic, Gorazd; Vollmer, Michael

    2008-01-01

    The surface-to-volume ratio is an important quantity in thermal physics. For example it governs the behaviour of heating or cooling of physical objects as a function of size like, e.g. cubes or spheres made of different material. The starting point in our paper is the simple physics problem of how cheese cubes of different sizes behave if heated…

  8. Temperature Mapping of Air Film-Cooled Thermal Barrier Coated Surfaces Using Phosphor Thermometry

    Science.gov (United States)

    Eldridge, Jeffrey I.

    2016-01-01

    While the effects of thermal barrier coating (TBC) thermal protection and air film cooling effectiveness for jet engine components are usually studied separately, their contributions to combined cooling effectiveness are interdependent and are not simply additive. Therefore, combined cooling effectiveness must be measured to achieve an optimum balance between TBC thermal protection and air film cooling. Phosphor thermometry offers several advantages for mapping temperatures of air film cooled surfaces. While infrared thermography has been typically applied to study air film cooling effectiveness, temperature accuracy depends on knowing surface emissivity (which may change) and correcting for effects of reflected radiation. Because decay time-based full-field phosphor thermometry is relatively immune to these effects, it can be applied advantageously to temperature mapping of air film-cooled TBC-coated surfaces. In this presentation, an overview will be given of efforts at NASA Glenn Research Center to perform temperature mapping of air film-cooled TBC-coated surfaces in a burner rig test environment. The effects of thermal background radiation and flame chemiluminescence on the measurements are investigated, and the strengths and limitations of this method for studying air film cooling effectiveness are discussed.

  9. Anaerobic digestion of waste activated sludge—comparison of thermal pretreatments with thermal inter-stage treatments

    DEFF Research Database (Denmark)

    Bangsø Nielsen, Henrik; Thygesen, Anders; Thomsen, Anne Belinda

    2011-01-01

    BACKGROUND: Treatment methods for improved anaerobic digestion (AD) of waste activated sludge were evaluated. Pretreatments at moderate thermal (water bath at 80 °C), high thermal (loop autoclave at 130–170 °C) and thermo-chemical (170 °C/pH 10) conditions prior to AD in batch vials (40 days/37 °C...

  10. Thermal Behaviour of Unusual Local-Scale Surface Features on Vesta

    Science.gov (United States)

    Tosi, F.; Capria, M. T.; De Sanctis, M. C.; Palomba, E.; Grassi, D.; Capaccioni, F.; Ammannito, E.; Combe, J.-Ph.; Sunshine, J. M.; McCord, T. B.; Titus, T. N.; Russell, C. T.; Raymond, C. A.; Mittlefehldt, D. W.; Toplis, M. J.; Forni, O.; Sykes, M. V.

    2012-01-01

    On Vesta, the region of the infrared spectrum beyond approximately 3.5 micrometers is dominated by the thermal emission of the asteroid's surface, which can be used to determine surface temperature by means of temperature-retrieval algorithms. The thermal behavior of areas of unusual albedo seen at the local scale can be related to physical properties that can provide information about the origin of those materials. Dawn's Visible and Infrared Mapping Spectrometer (VIR) hyperspectral cubes are used to retrieve surface temperatures, with high accuracy as long as temperatures are greater than 180 K. Data acquired in the Survey phase (23 July through 29 August 2011) show several unusual surface features: 1) high-albedo (bright) and low-albedo (dark) material deposits, 2) spectrally distinct ejecta, 3) regions suggesting finer-grained materials. Some of the unusual dark and bright features were re-observed by VIR in the subsequent High-Altitude Mapping Orbit (HAMO) and Low-Altitude Mapping Orbit (LAMO) phases at increased pixel resolution. To calculate surface temperatures, we applied a Bayesian approach to nonlinear inversion based on the Kirchhoff law and the Planck function. These results were cross-checked through application of alternative methods. Here we present temperature maps of several local-scale features that were observed by Dawn under different illumination conditions and different local solar times. Some bright terrains have an overall albedo in the visible as much as 40% brighter than surrounding areas. Data from the IR channel of VIR show that bright regions generally correspond to regions with lower thermal emission, i.e. lower temperature, while dark regions correspond to areas with higher thermal emission, i.e. higher temperature. This behavior confirms that many of the dark appearances in the VIS mainly reflect albedo variations. In particular, it is shown that during maximum daily insolation, dark features in the equatorial region may rise to

  11. Does Titan have an Active Surface?

    Science.gov (United States)

    Nelson, R.

    2009-12-01

    ammonia, a compound expected in Titan’s interior. This, combined with the previous evidence from VIMS and RADAR images, creates a strong case for Titan having a presently active surface, possibly due to cryovolcanism. Cassini encountered Titan at very close range on 2008-11-19-13:58 and again on 2008-12-05-12:38. These epochs are called T47 and T48. Comparison of earlier lower resolution data (T5) with the recent T47 and T48 data reveal changes of the surface reflectance and morphology in the Hotei region. This is the first evidence from VIMS that confirms the RADAR report that Hotei Reggio has morphology consistent with volcanic terrain. It has not escaped our attention that ammonia, in association with methane and nitrogen, the principal species of Titan’s atmosphere, closely replicates the environment at the time that live first emerged on earth. If Titan is currently active then these results raise the following questions: What is the full extent of current geologic activity? What are the ongoing processes? Are Titan’s chemical processes today supporting a prebiotic chemistry similar to that under which life evolved on Earth? This work done at JPL under contract with NASA. Refs: [1]R. M. Nelson et al., Icarus 199 (2009) 429-441. [2]R. M. Nelson et al., GRL, VOL. 36, L04202, doi:10.1029/2008GL036206, 2009. [3]S. D. Wall GRL, VOL. 36, L04203, doi:10.1029/2008GL036415, 2009

  12. The Surface Finish of Thermally Aged Carbon Fibre Reinforced Composites Using E-glass as a Surface Barrier

    Science.gov (United States)

    de Souza, M. L.; Fox, B. L.

    2015-10-01

    This work investigated the effect of woven E-glass mass (25 g/m2, 50 g/m2, 85 g/m2, 135 g/m2) on the painted surface finish of various thermoset (EPIKOTETM RIM935, EPIKOTETM 04434, Ultratec LpTM ES300, Ultratec LpTM SPV6035) carbon fibre composite laminates, before and after aging at 95 °C for 168 h. The as-moulded laminate surfaces were evaluated using surface profilometry techniques and the painted and aged surfaces were evaluated using a wave-scan distinctness of image (DOI) instrument. It was found that the 25 g/m2 E-glass surface layer assisted with reducing the roughness of the as-moulded surfaces and the long-term waviness of the painted surfaces due to the increase in resin-richness at the surface. The EPIKOTETM 04434 resin system that contained diglycidyl ether of bisphenol F (DGEBF) epoxy had the least change in long-term waviness with thermal aging due to the rigid fluorene-based backbone in comparison to the diglycidyl ether of bisphenol A (DGEBA) systems.

  13. Solar-induced thermal activity and stratification in pond water

    CERN Document Server

    Brownridge, James D

    2015-01-01

    Ponds are universally used to store water for a large number of uses. With the increasing demand for more fresh water, ponds, lakes and reservoirs are likely to be constructed on a larger scale. We must understand the effects of environmental changes on fresh water if we are to most efficiently utilize this resource. This study undertakes to increase our understanding of the rate of thermal response of ponds and other bodies of water to every-day environmental changes. The central research agenda is to investigate how the temperature of pond water from top to bottom responds to the day/night cycle, changes in air temperature just above the surface, cloud conditions, and other sudden environmental changes. Data collection for this study spanned October 2007 to June 2011 and had a continuous time resolution of 50 seconds.

  14. Preparing Al-Mg Substrate for Thermal Spraying: Evaluation of Surface State After Different Pretreatments

    Science.gov (United States)

    Lukauskaitė, R.; Valiulis, A. V.; Černašėjus, O.; Škamat, J.; Rębiś, J. A.

    2016-08-01

    The article deals with the pretreatment technique for preparing the surface of aluminum alloy EN AW 5754 before thermal spray. The surface after different pretreatments, including degreasing with acetone, chemical etching with acidic and alkali solutions, grit-blasting, cathodic cleaning, and some combinations of these techniques, has been studied. The investigation of pre-treated surfaces covered the topographical study (using scanning electron microscopy, atomic force microscopy, and 3D profilometry), the chemical analysis by x-ray photoelectron spectroscopy, the evaluation of surface wettability (sessile drop method), and the assessment of surface free energy. Compared with all the techniques used in present work, the cathodic cleaning and its combination with grit-blasting provide the most preferable chemistry of the surface. Due to the absence of hydroxides at the surface and, possible, due to the diffusion of magnesium to the surface of substrate, the surface wettability and the surface free energy have been significantly improved. No direct correlation between the surface topography and the surface wettability has been established.

  15. Embedded active surfaces for volume visualization

    Science.gov (United States)

    Whitaker, Ross T.; Chen, David

    1994-05-01

    We propose a new technique for use in the visualization of sparse, fuzzy, or noisy 3D data. This technique incorporates the methods of deformable or active models that have been developed in 2D computer vision. In this paper we generalize such models to 3D in a manner that is both practical and mathematically elegant, and we thereby avoid many of the problems associated with previous attempts to generalize deformable models. When generalizing to 3D, deformable models have several drawbacks-- including their acute sensitivity to topology, parameterization, and initial conditions--which limit their effectiveness. Many of these problems stem from the underlying parameterization of the model. This paper presents an implicit representation of deformable models. The implicit representation is an embedding of objects as level sets of grayscale functions which serve as templates. The evolution equation associated with the energy minimization process for a model has an analogous partial differential equation which governs the behavior of the corresponding grayscale template. We show that the 'active blobs' associated with the embedding of active models have several useful properties. First, they are topologically flexible. Second, grayscale images represent families of models. Third, when surfaces are embedded as grayscale images, they are described by a natural scale space. This scale space provides the ability to solve these equations in a multi-scale manner. Several 2D examples of technique are presented, as well as some visualization results from 3D ultrasound.

  16. Microstructure evolution and surface cleaning of Cu nanoparticles during micro-forming fields activated sintering technology

    Directory of Open Access Journals (Sweden)

    Wu Mingxia

    2015-01-01

    Full Text Available For the purpose of extensive utilization of powder metallurgy to micro/nano- fabrication of materials, the micro gear was prepared by a novel method, named as micro- forming fields activated sintering technology (Micro-FAST. Surface-cleaning of particles, especially during the initial stage of sintering, is a crucial issue for the densification mechanism. However, up to date, the mechanism of surface-cleaning is too complicated to be known. In this paper, the process of surface-cleaning of Micro-FAST was studied, employing the high resolution transmission electron microscopy (HRTEM for observation of microstructure of micro-particles. According to the evolution of the microstructure, surface-cleaning is mainly ascribed to the effect of electro-thermal focusing. The process of surface-cleaning is achieved through rearrangement of grains, formation of vacancy, migration of vacancy and enhancement of electro-thermal focusing.

  17. Surface and thermal properties of collagen/hyaluronic acid blends containing chitosan.

    Science.gov (United States)

    Lewandowska, Katarzyna; Sionkowska, Alina; Grabska, Sylwia; Kaczmarek, Beata

    2016-11-01

    The structure and surface properties of binary and ternary blends containing collagen (Coll), hyaluronic acid (HA) and chitosan (Ch) were investigated by contact angle measurements, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and atomic force microscopy (AFM). Thin films of Coll/HA and Coll/HA/Ch blends have been formed by casting methods from aqueous acid solutions. The surface roughness, hydrophobic/hydrophilic character and thermal stability of Coll/HA were changed after addition of chitosan. Thermal stability of binary blends increase upon the addition of chitosan. The results of contact angle and the surface free energy revealed that hyaluronic acid films are more polar than collagen and chitosan films. The surface energy and its polar and dispersive components of binary and ternary blends were calculated and more hydrophilic films were produced by the addition of HA and chitosan, also resulting in more thermally stabile materials. These results demonstrate that collagen interacts with hyaluronic acid and chitosan changing the surface properties of polymer films.

  18. Thermal transport study across interface “nanostructured solid surface / fluid” by photoacoustic technique

    Science.gov (United States)

    Voitenko, K.; Isaiev, M.; Pastushenko, A.; Andrusenko, D.; Kuzmich, A.; Lysenko, V.; Burbelo, R.

    2017-01-01

    In the paper the experimental study of heat transport across the interface “porous silicon/liquid” by photoacoustic technique is reported. Two cases with and without liquid covering of porous silicon surface were considered. Thermal perturbations were excited at the surface of porous silicon as a result of absorption of the light with modulated intensity. The resulting thermal-elastic stresses arising in the system were registered with piezoelectric transducer. The amplitude-frequency dependencies of the voltage on the piezoelectric electrodes were measured. The presence of the liquid film leads to decreasing of the amplitude of photoacoustic signal as a result of the thermal energy evacuation from the porous silicon into the liquid. The experimental dependencies were fitted with the results of simulation that takes into account heat fluxes separation at the porous silicon/liquid interface. With the presented method one can precisely measure heat fluxes transferred from the solid into contacting fluid. Moreover, the presented approach can be easily adopted for the thermal conductivity study of the different nanofluids as well as thermal resistance at the interface nanostructured solid/fluid.

  19. Thermal, spectral, and surface properties of LED light-polymerized bulk fill resin composites.

    Science.gov (United States)

    Pişkin, Mehmet Burçin; Atalı, Pınar Yılmaz; Figen, Aysel Kantürk

    2015-02-01

    The aim of this study was to evaluate the thermal, spectral, and surface properties of four different bulk fill materials – SureFil SDR (SDR, Dentsplay DETREY), QuixFil (QF, Dentsplay DETREY), X-tra base (XB, Voco) X-tra fil (XF, Voco) – polymerized by light-emitting diode (LED). Resin matrix, filler type, size and amount, and photoinitiator types influence the degree of conversion. LED-cured bulk fill composites achieved sufficient polymerization. Scanning electron microscope (SEM) analysis revealed different patterns of surface roughness, depending on the composite material. Bulk fill materials showed surface characteristics similar to those of nanohybrid composites. Based on the thermal analysis results, glass transition (T(g)) and initial degradation (T(i)) temperatures changed depending on the bulk fill resin composites.

  20. Simultaneous dopant diffusion and surface passivation in a single rapid thermal cycle

    Energy Technology Data Exchange (ETDEWEB)

    Lachiq, A.; Slaoui, A.; Georgopoulos, L.; Ventura, L.; Monna, R.; Muller, J.C. [Laboratoire PHASE, 67 - Strasbourg (France)

    1996-09-01

    Results on simultaneous formation of emitter/back-surface field or emitter/surface passivation in a single rapid thermal cycle are presented. We have investigated the diffusion kinetics of dopant elements like phosphorus, boron (from a doped spin-on glass (SOD) film), aluminium (from evaporated films) or aluminium-boron (from an Al-B SOD film). In particular, we have shown that rapid thermal co-diffusion of P and Al (or Al-B) leads to low sheet resistances, optical emitter profiles and a high gettering effect. Furthermore, the possibility of using the remaining SOD films as a surface passivation layer was investigated. Dark saturation current measurements as deduced from the photoconductivity decay technique demonstrate the passivation effect of the remaining SOD film. The highest efficiency of 12.8% obtained was achieved on SOD oxide-coated solar cells. (author)

  1. Kinetics of Thermally Activated Physical Processes in Disordered Media

    Directory of Open Access Journals (Sweden)

    Bertrand Poumellec

    2015-07-01

    Full Text Available We describe a framework for modeling the writing and erasure of thermally-distributed activated processes that we can specifically apply to UV-induced refractive index change, particularly in fibers. From experimental measurements (isochrons and/or isotherms, this framework allows to find the distribution function of the activation energy by providing only a constant, which can be determined by a simple variable change when a few assumptions are fulfilled. From this modeling, it is possible to know the complete evolution in time of the system. It is also possible to determine the annealing conditions for extending a lifetime. This approach can also be used for other physical quantities, such as photodarkening, stress relaxation, and luminescence decay, provided that it can be described by a distribution function.

  2. Transient Thermal Model and Analysis of the Lunar Surface and Regolith for Cryogenic Fluid Storage

    Science.gov (United States)

    Christie, Robert J.; Plachta, David W.; Yasan, Mohammad M.

    2008-01-01

    A transient thermal model of the lunar surface and regolith was developed along with analytical techniques which will be used to evaluate the storage of cryogenic fluids at equatorial and polar landing sites. The model can provide lunar surface and subsurface temperatures as a function of latitude and time throughout the lunar cycle and season. It also accounts for the presence of or lack of the undisturbed fluff layer on the lunar surface. The model was validated with Apollo 15 and Clementine data and shows good agreement with other analytical models.

  3. Modification of proteins with cyclodextrins prevents aggregation and surface adsorption and increases thermal stability.

    Science.gov (United States)

    Prashar, Deepali; Cui, DaWei; Bandyopadhyay, Debjyoti; Luk, Yan-Yeung

    2011-11-01

    This work describes a general approach for preventing protein aggregation and surface adsorption by modifying proteins with β-cyclodextrins (βCD) via an efficient water-driven ligation. As compared to native unmodified proteins, the cyclodextrin-modified proteins (lysozyme and RNase A) exhibit significant reduction in aggregation, surface adsorption and increase in thermal stability. These results reveal a new chemistry for preventing protein aggregation and surface adsorption that is likely of different mechanisms than that by modifying proteins with poly(ethylene glycol).

  4. Thermal and electrochemical studies of carbons for Li-ion batteries. 2. Correlation of active sites and irreversible capacity loss

    Science.gov (United States)

    Tran, T.; Yebka, B.; Song, X.; Nazri, G.; Kinoshita, K.; Curtis, D.

    Thermal gravimetric analysis (TGA) and differential thermal analysis (DTA) involving air oxidation of fluid coke, coal-tar pitch delayed coke and needle coke suggested that active sites are present which can be correlated to the crystallographic parameters, La and Lc, and the d(002) spacing. This finding was extended to determine the relationship between active sites on carbon and their role in catalyzing electrolyte decomposition leading to irreversible capacity loss (ICL) in Li-ion batteries. Electrochemical data from this study with graphitizable carbons and from published literature were analyzed to determine the relationship between the physical properties of carbon and the ICL during the first charge/discharge cycle. Based on this analysis, we conclude that the active surface area, and not the total BET surface area, has an influence on the ICL of carbons for Li-ion batteries. This conclusion suggests that the carbon surface structure plays a significant role in catalyzing electrolyte decomposition.

  5. Effect of thermal post-treatment on some surface-related properties of oriented strandboards

    Directory of Open Access Journals (Sweden)

    Cláudio Henrique Soares Del Menezzi

    2008-07-01

    Full Text Available A very promising method for improving the dimensional stability of oriented strandboard (OSB has been studied in Brazil since 2001. According to this method, the OSB is thermally treated under mild conditions using a hot-press, where it is reheated without high level of compression stress. The properties of the treated OSB panels are different from and enhanced compared to those untreated ones. It means that the treated OSB can be used in more severe uses, like concrete formwork. This paper aims to evaluate the effect of the proposed thermal treatment on nail-holding capability and on surface hardness of OSB. Samples from 42 commercials OSB were thermally treated according to two levels of temperature (190°C and 220°C and three heating times (12, 16 and 20 min using a single opening hot-press. For comparison, control panels were kept untreated. The following surface-related properties were evaluated: Janka hardness, nail-holding capability in a plane normal to the surface, in the edge of the panel, water absorption and thickness swelling (TS of edge sealed samples, and four surface roughness parameters. According to the Dunnett test, there were significant differences between treated and untreated panels for nail-holding, dimensional stability and surface roughness. The factorial ANOVA identified that the temperature was the main factor governing these properties while the duration of the treatment had lesser effect. It was concluded that the proposed thermal treatment improved significantly dimensional stability and did not affect adversely the nail-holding capability and surface roughness of the treated OSB

  6. Structural, thermal and surface characterization of thermoplastic polyurethanes based on poly(dimethylsiloxane

    Directory of Open Access Journals (Sweden)

    Pergal Marija V.

    2014-01-01

    Full Text Available In this study, the synthesis, structure and physical properties of two series of thermoplastic polyurethanes based on hydroxypropyl terminated poly(dimethylsiloxane (HP-PDMS or hydroxyethoxy propyl terminated poly(dimethylsiloxane (EO-PDMS as a soft segment, and 4,4’-methylenediphenyl diisocyanate and 1,4-butanediol as a hard segment were investigated. Each series is composed of samples prepared with a different soft segment. The polyurethanes were synthesized by two-step polyaddition in solution. The effects of the type and content of PDMS segments on the structure, thermal and surface properties of copolymers were studied by 1H NMR, 13C NMR and two-dimensional NMR (HMBC and ROESY spectroscopy, GPC, DSC, TGA, WAXS, SEM, water contact angle and water absorption measurements. Thermal properties investigated by DSC indicated that the presence of soft PDMS segments lowers the glass transition and melting temperatures of the hard phase as well as the degree of crystallinity. SEM analysis of copolymers with a lower soft segment content confirmed the presence of spherulite superstructures, which arise from the crystallization of the hard segments. When compared with polyurethanes prepared from HP-PDMS, copolymers synthesized from EO-PDMS with the same content of the soft segments have higher degree of crystallinity, better thermal stability and less hydrophobic surface. Our results show that the synthesized polyurethanes have good thermal and surface properties, which could be further modified by changing the type or content of the soft segments.

  7. A dynamic tester to evaluate the thermal and moisture behaviour of the surface of textiles.

    Science.gov (United States)

    Li, Wenbin; Xu, Weilin; Wang, Hao; Wang, Xin

    2016-01-01

    The thermal and moisture behaviour of the microclimate of textiles is crucial in determining the physiological comfort of apparel, but it has not been investigated sufficiently due to the lack of particular evaluation techniques. Based on sensing, temperature controlling and wireless communicating technology, a specially designed tester has been developed in this study to evaluate the thermal and moisture behaviour of the surface of textiles in moving status. A temperature acquisition system and a temperature controllable hotplate have been established to test temperature and simulate the heat of human body, respectively. Relative humidity of the surface of fabric in the dynamic process has been successfully tested through sensing. Meanwhile, wireless communication technology was applied to transport the acquired data of temperature and humidity to computer for further processing. Continuous power supply was achieved by intensive contact between an elastic copper plate and copper ring on the rotating shaft. This tester provides the platform to evaluate the thermal and moisture behaviour of textiles. It enables users to conduct a dynamic analysis on the temperature and humidity together with the thermal and moisture transport behaviour of the surface of fabric in moving condition. Development of this tester opens the door of investigation on the micro-climate of textiles in real time service, and eventually benefits the understanding of the sensation comfort and wellbeing of apparel wearers.

  8. Design of Ag nanorods for sensitivity and thermal stability of surface-enhanced Raman scattering

    Science.gov (United States)

    Ma, Lingwei; Zhang, Zhengjun; Huang, Hanchen

    2017-10-01

    The technology of surface-enhanced Raman scattering (SERS) has found many applications and may find more if it can possess both sensitivity and thermal stability. This paper reports a rational design of Ag nanorods to simultaneously achieve two competing goals: the sensitivity and the thermal stability of SERS substrates. The Ag nanorods are designed and synthesized using physical vapor deposition under the condition of glancing angle incidence. The working pressure of the vacuum chamber is controlled so the mean free path of depositing atoms is comparable to the dimension of the chamber, so as to grow Ag nanorods with small diameter, and small but clear separation for optimal SERS sensitivity. Such Ag nanorods are further capped with Al2O3 on their top surfaces to reduce the diffusion-induced coarsening at high temperatures, and thereby to improve the thermal stability for SERS detections. Meanwhile, since the side surfaces of Ag nanorods are not coated with oxides in this approach, the SERS sensitivity is largely preserved while good thermal stability is achieved.

  9. An Analysis of Thermally-Related Surface Rainfall Budgets Associated with Convective and Stratiform Rainfall

    Institute of Scientific and Technical Information of China (English)

    ZHOU Yushu; Xiaofan LI

    2011-01-01

    Both water vapor and heat processes play key roles in producing surface rainfall.While the water vapor effects of sea surface temperature and cloud radiative and microphysical processes on surface rainfall have been investigated in previous studies,the thermal effects on rainfall are analyzed in this study using a series of two-dimensional equilibrium cloud-resolving model experiments forced by zonally-uniform,constant,large-scale zonal wind and zero large-scale vertical velocity.The analysis of thermally-related surface rainfall budget reveals that the model domain mean surface rain rate is primarily associated with the mean infrared cooling rate.Convective rainfall and transport of hydrometeor concentration from convective regions to raining stratiform regions corresponds to the heat divergence over convective regions,whereas stratiform rainfall corresponds to the transport of hydrometeor concentration from convective regions and heat divergence over raining stratiform regions.The heat divergence over convective regions is mainly balanced by the heat convergence over rainfall-free regions,which is,in turn,offset by the radiative cooling over rainfall-free regions.The sensitivity experiments of rainfall to the effects of sea surface temperature and cloud radiative and microphysical processes show that the sea surface temperature and cloud processes affect convective rainfall through the changes in infrared cooling rate over rainfall-free regions and transport rate of heat from convective regions to rainfall-free regions.

  10. Thermal Marangoni Convection of Two-phase Dusty Fluid Flow along a Vertical Wavy Surface

    Directory of Open Access Journals (Sweden)

    S. Siddiqa

    2017-01-01

    Full Text Available The paper considers the influence of thermal Marangoni convection on boundary layer flow of two-phase dusty fluid along a vertical wavy surface. The dimensionless boundary layer equations for two-phase problem are reduced to a convenient form by primitive variable transformations (PVF and then integrated numerically by employing the implicit finite difference method along with the Thomas Algorithm. The effect of thermal Marangoni convection, dusty water and sinusoidal waveform are discussed in detail in terms of local heat transfer rate, skin friction coefficient, velocity and temperature distributions. This investigation reveals the fact that the water-particle mixture reduces the rate of heat transfer, significantly.

  11. Methods for estimating pressure and thermal loads induced by elevon deflections on hypersonic-vehicle surfaces with turbulent boundary layers

    Science.gov (United States)

    Kaufman, L. G., II; Johnson, C. B.

    1981-01-01

    Empirical anaytic methods are presented for calculating thermal and pressure distributions in three-dimensional, shock-wave turbulent-boundary-layer, interaction-flow regions on the surface of controllable hypersonic aircraft and missiles. The methods, based on several experimental investigations, are useful and reliable for estimating both the extent and magnitude of the increased thermal and pressure loads on the vehicle surfaces.

  12. Surface modification of several dental substrates by non-thermal, atmospheric plasma brush

    Science.gov (United States)

    Chen, Mingsheng; Zhang, Ying; Driver, M. Sky; Caruso, Anthony N.; Yu, Qingsong; Wang, Yong

    2013-01-01

    Objective The purpose of this study was to reveal the effectiveness of non-thermal atmospheric plasma brush in surface wettability and modification of four dental substrates. Methods Specimens of dental substrates including dentin, enamel, and two composites Filtek Z250, Filtek LS Silorane were prepared (~2 mm thick, ~10 mm diameter). The prepared surfaces were treated for 5–45 s with a non-thermal atmospheric plasma brush working at temperatures from 36 to 38 °C. The plasma-treatment effects on these surfaces were studied with contact-angle measurement, X-ray photoemission spectroscopy (XPS) and scanning electron microscopy (SEM). Results The non-thermal atmospheric argon plasma brush was very efficient in improving the surface hydrophilicity of four substrates studied. The results indicated that water contact angle values decreased considerably after only 5 s plasma treatment of all these substrates. After 30 s treatment, the values were further reduced to <5°, which was close to a value for super hydrophilic surfaces. XPS analysis indicated that the percent of elements associated with mineral in dentin/enamel or fillers in the composites increased. In addition, the percent of carbon (%C) decreased while %O increased for all four substrates. As a result, the O/C ratio increased dramatically, suggesting that new oxygen-containing polar moieties were formed on the surfaces after plasma treatment. SEM surface images indicated that no significant morphology change was induced on these dental substrates after exposure to plasmas. Significance Without affecting the bulk properties, a super-hydrophilic surface could be easily achieved by the plasma brush treatment regardless of original hydrophilicity/hydrophobicity of dental substrates tested. PMID:23755823

  13. Thermal, Electrical and Surface Hydrophobic Properties of Electrospun Polyacrylonitrile Nanofibers for Structural Health Monitoring

    Directory of Open Access Journals (Sweden)

    Ibrahim M. Alarifi

    2015-10-01

    Full Text Available This paper presents an idea of using carbonized electrospun Polyacrylonitrile (PAN fibers as a sensor material in a structural health monitoring (SHM system. The electrospun PAN fibers are lightweight, less costly and do not interfere with the functioning of infrastructure. This study deals with the fabrication of PAN-based nanofibers via electrospinning followed by stabilization and carbonization in order to remove all non-carbonaceous material and ensure pure carbon fibers as the resulting material. Electrochemical impedance spectroscopy was used to determine the ionic conductivity of PAN fibers. The X-ray diffraction study showed that the repeated peaks near 42° on the activated nanofiber film were α and β phases, respectively, with crystalline forms. Contact angle, thermogravimetric analysis (TGA, differential scanning calorimetry (DSC and Fourier transform infrared spectroscopy (FTIR were also employed to examine the surface, thermal and chemical properties of the carbonized electrospun PAN fibers. The test results indicated that the carbonized PAN nanofibers have superior physical properties, which may be useful for structural health monitoring (SHM applications in different industries.

  14. Thermal, Electrical and Surface Hydrophobic Properties of Electrospun Polyacrylonitrile Nanofibers for Structural Health Monitoring.

    Science.gov (United States)

    Alarifi, Ibrahim M; Alharbi, Abdulaziz; Khan, Waseem S; Swindle, Andrew; Asmatulu, Ramazan

    2015-10-14

    This paper presents an idea of using carbonized electrospun Polyacrylonitrile (PAN) fibers as a sensor material in a structural health monitoring (SHM) system. The electrospun PAN fibers are lightweight, less costly and do not interfere with the functioning of infrastructure. This study deals with the fabrication of PAN-based nanofibers via electrospinning followed by stabilization and carbonization in order to remove all non-carbonaceous material and ensure pure carbon fibers as the resulting material. Electrochemical impedance spectroscopy was used to determine the ionic conductivity of PAN fibers. The X-ray diffraction study showed that the repeated peaks near 42° on the activated nanofiber film were α and β phases, respectively, with crystalline forms. Contact angle, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FTIR) were also employed to examine the surface, thermal and chemical properties of the carbonized electrospun PAN fibers. The test results indicated that the carbonized PAN nanofibers have superior physical properties, which may be useful for structural health monitoring (SHM) applications in different industries.

  15. Thermal development of latent fingermarks on porous surfaces--further observations and refinements.

    Science.gov (United States)

    Song, Di Fei; Sommerville, Daniel; Brown, Adam G; Shimmon, Ronald G; Reedy, Brian J; Tahtouh, Mark

    2011-01-30

    In a further study of the thermal development of fingermarks on paper and similar surfaces, it is demonstrated that direct contact heating of the substrate using coated or ceramic surfaces at temperatures in excess of 230°C produces results superior to those obtained using hot air. Fingermarks can also be developed in this way on other cellulose-based substrates such as wood and cotton fabric, though ridge detail is difficult to obtain in the latter case. Fluorescence spectroscopy indicates that the phenomena observed during the thermal development of fingermarks can be reproduced simply by heating untreated white copy paper or filter paper, or these papers treated with solutions of sodium chloride or alanine. There is no evidence to suggest that the observed fluorescence of fingermarks heated on paper is due to a reaction of fingermark constituents on or with the paper. Instead, we maintain that the ridge contrast observed first as fluorescence, and later as brown charring, is simply an acceleration of the thermal degradation of the paper. Thermal degradation of cellulose, a major constituent of paper and wood, is known to give rise to a fluorescent product if sufficient oxygen is available [1-5]. However, the absence of atmospheric oxygen has only a slight effect on the thermal development of fingermarks, indicating that there is sufficient oxygen already present in paper to allow the formation of the fluorescent and charred products. In a depletion study comparing thermal development of fingermarks on paper with development using ninhydrin, the thermal technique was found to be as sensitive as ninhydrin for six out of seven donors. When thermal development was used in sequence with ninhydrin and DFO, it was found that only fingermarks that had been developed to the fluorescent stage (a few seconds of heating) could subsequently be developed with the other reagents. In the reverse sequence, no useful further development was noted for fingermarks that were

  16. Ground surface thermal regime of rock glaciers in the High Tatra Mts., Slovakia

    Science.gov (United States)

    Uxa, Tomáš; Mida, Peter

    2017-04-01

    Numerous lobate- or tongue-shaped debris accumulations, mostly interpreted as rock glaciers, have recently been recognized in the High Tatra Mts., Slovakia (49˚ 10' N, 20˚ 08' E). These prominent landforms arise due to creep of voluminous debris-ice mixtures, and as such they are excellent indicators of present or past permafrost existence. Hence rock glaciers are extensively utilized to model the distribution of permafrost in mountain areas. However, commonly applied rules of thumb may not be entirely indicative to discriminate particularly between the inactive (permafrost in disequilibrium with present climate) and relict (without permafrost) rock glaciers, which may substantially complicate permafrost modelling. Accordingly, the information about their thermal state is essential to calibrate and validate regional permafrost models. Limited ground temperature data have been, however, available from the High Tatra Mts. to date and therefore, we bring the updated and enhanced results from the thermal investigations of eleven rock glaciers located in the Slavkovská dolina and Veľká Studená dolina valleys at elevations between 1832 and 2090 m asl. Ground surface temperature (GST) has been continuously monitored at seven rock glaciers between October 2014 and September 2016 using nine Minikin Tie (EMS Brno Inc.) and iButton DS1922L (Maxim Integrated Inc.) loggers with an accuracy of ±0.2 and ±0.5 ˚ C, respectively. In addition, the bottom temperature of snow (BTS) was measured at 306 locations during spring of 2015 and 2016 to map potential permafrost occurrence within all the surveyed rock glaciers and in their immediate surroundings. Mean annual ground surface temperature (MAGST) of the rock glaciers ranged between -1.3 ˚ C and +2.6 ˚ C and averaged +1.0 ˚ C and +0.8 ˚ C in 2014-2015 and 2015-2016, respectively. Two sites continually showed negative MAGST and two other sites were below +0.5 ˚ C and +1.0 ˚ C, respectively. This strongly contrasts with

  17. Monitoring Thermal Activity of Eastern Anatolian Volcanoes Using MODIS Images

    Science.gov (United States)

    Diker, Caner; Ulusoy, Inan

    2014-05-01

    MODIS (Moderate Resolution Imaging Spectroradiometer) instrument is used for imaging atmosphere, land and ocean with 36 bands. Both AQUA and TERRA platforms acquire 2 images daily (daytime and nighttime). Low temperature anomalies on volcanoes comprise important clues. Low temperature anomalies on Holocene volcanoes of Eastern Anatolia were investigated for these clues using MODIS Land Surface Temperature (LST) images. A total of 16800 daily LST images dated between 2001 and 2012 have been processed using a code written in IDL (Interactive Data Language). Factors like shadow, ice/snow and clouds that are affecting the reflectance data are masked. The mask is derived from MODIS reflectance data state image. Various LST images are calculated: Two nested region of interest (ROI) windows (square/rectangular) have been selected on the images. First is the bigger window, which covers the whole area of the volcano (Total volcano area). Second one is a smaller window which circumference the summit (crater and/or caldera) of the volcano (Summit cone) where thermal output is generally higher when compared to the flanks. Two data sets have been calculated using the ROI's for each volcano. The first set contains daytime and nighttime raw data without any correction. The second set contains topographically corrected images; daytime images are corrected using Cosine and Minnaert methods and nighttime images are corrected using three step normalization method. Calculated surface temperatures (Tmax, Tmin, Tmean) are plotted annually. On Nemrut Volcano as an example, maximum and minimum temperatures are between 26.31oC and -44.87oC on nighttime data for twelve years period. Temperature difference between total volcano area ROI and summit cone ROI are calculated (ΔT). High ΔT indicates that there is an increase of temperature at the summit cone when compared to the total volcano area. STA/LTA (Short Term Average/Long Term Average) filter was applied to maximum temperature and

  18. Structural and Computational Study of 4 New Solvatomorphs of Betulin: A Combined X-Ray, Hirshfeld Surface, and Thermal Analysis.

    Science.gov (United States)

    Yang, Dezhi; Gong, Ningbo; Zhang, Li; Lu, Yang; Du, Guanhua

    2017-03-01

    Four new solvatomorphs of betulin were reported and characterized by X-ray diffractometry as well as thermal and vibrational spectroscopic analyses. Single-crystal X-ray diffraction was used to analyze the X-ray structures of the compounds and confirmed the stoichiometric ratio between the host and guest molecules from thermal data. Results indicated that solvatomorphism occurred in several betulin solvates. Changes in intermolecular arrangements, stoichiometry, and hydrogen-bonding interactions of solvatomorphs were due to solvent incorporation to solvates. Hirshfeld surface analyses, especially dnorm surface and fingerprint plots, were used to determine intermolecular interactions in the crystal network. Solvent molecules played an important role in the construction of a 3D architecture. The stabilities of these solvates were evaluated by thermal analyses. Nonisothermal kinetic analysis was used to explain the kinetics of solid-solid phase transition (desolvation) of betulin solvates. The apparent activation energies were evaluated using Kissinger and Ozawa methods. Moreover, phase transitions were visually investigated by hot-stage microscopic analysis. Copyright © 2017. Published by Elsevier Inc.

  19. Thermal activation of an industrial sludge for a possible valorization

    Directory of Open Access Journals (Sweden)

    Lamrani Sanae

    2014-04-01

    Full Text Available This work fits within the framework of sustainable management of sludge generated from wastewater treatment in industrial network. The studied sludge comes from an industry manufacturing sanitary ware products.Physico-chemical and mineralogical characterization was performed to give an identity card to the sludge. We noted the absence of metal pollution.The industrial sludge has been subjected to thermal activation at various temperatures (650°C to 850°C. The pozzolanic activity was evaluated by physico- chemical and mechanical methods [1]. Pozzolanicity measurement was carried out based on Chapelle test and conductivity revealed the existence of pozzolanic properties of the calcined samples. The best pozzolanic reactivity was obtained for the sample calcined at 800°C. We noticed a decrease in the reactivity of the sample calcined at 850°C. In addition, analysis by means of X-ray diffraction and Fourier transform infrared spectroscopy showed that sludge recrystallization begins at a temperature of 850°C. Pozzolanicity index of the thermally treated samples was determined by measuring the mechanical resistance of mortar specimens previously kept in a saturated lime solution for 28 days (ASTM C618 [2]. The best pozzolanic activity index was obtained for the sample calcined at 800°C (109.1%.This work is a contribution to the research for new supplying sources of raw materials and additives in the field of construction. It presents a proposition of a promising solution for the valorization of waste material as an additive instead of being discharged into open air dumps causing a major environmental problem.

  20. The effect of polyether functional polydimethylsiloxane on surface and thermal properties of waterborne polyurethane

    Science.gov (United States)

    Zheng, Guikai; Lu, Ming; Rui, Xiaoping

    2017-03-01

    Waterborne polyurethanes (WPU) modified with polyether functional polydimethylsiloxane (PDMS) were synthesized by pre-polymerization method using isophorone diisocyanate (IPDI) and 1,4-butanediol (BDO) as hard segments and polybutylene adipate glycol (PBA) and polyether functional PDMS as soft segments. The effect of polyether functional PDMS on phase separation, thermal properties, surface properties including surface composition, morphology and wettability were investigated by FTIR, contact angle measurements, ARXPS, SEM-EDS, AFM, TG and DSC. The results showed that the compatibility between urethane hard segment and PDMS modified with polyether was good, and there was no distinct phase separation in both bulk and surface of WPU films. The degradation temperature and low temperature flexibility increased with increasing amounts of polyether functional PDMS. The enrichment of polyether functional PDMS with low surface energy on the surface imparted excellent hydrophobicity to WPU films.

  1. Investigation of thermal processes during test operation of ingot mould with composite surface layer

    Directory of Open Access Journals (Sweden)

    J. Szajnar

    2008-08-01

    Full Text Available The paper presents a method of usable properties of surface layers improvement of grey cast iron EN-GJL-200 ingot mould, by put directly in founding process a composite surface layer on the basis of corundum Al2O3 and quartz sand SiO2. Technology of composite surface layer guarantee mainly increase in hardness and abrasive wear resistance of cast steel and cast iron castings on machine elements. This technology can be competition for generally applied welding technology (surfacing by welding and thermal spraying. The results of studies show, that is positive influence of composite surface layer with ceramic particles on increase in life of cast iron ingot moulds.

  2. Tuning the surface chemistry of lubricant-derived phosphate thermal films: The effect of boron

    Science.gov (United States)

    Spadaro, F.; Rossi, A.; Lainé, E.; Woodward, P.; Spencer, N. D.

    2017-02-01

    Understanding the interactions among the various additives in a lubricant is important because they can have a major influence on the performance of blends under tribological conditions. The present investigation is focused on the interactions occurring between ZnDTP and dispersant molecules in an oil formulation, and on their reactivity under purely thermal conditions in the presence of air-oxidized iron surfaces. Nuclear magnetic resonance spectroscopy (NMR) was performed on undiluted blends at different temperatures, while angle-resolved X-ray photoelectron spectroscopy (ARXPS) was exploited to investigate the surface reactivity on oxidized iron surfaces. The results indicate that the dispersant, generally added to blends for preventing the deposition of sludge, varnish and soot on the surface, might also inhibit the reaction of all other additives with the steel surface.

  3. Chlorine isotopes of thermal springs in arc volcanoes for tracing shallow magmatic activity

    Science.gov (United States)

    Li, Long; Bonifacie, Magali; Aubaud, Cyril; Crispi, Olivier; Dessert, Céline; Agrinier, Pierre

    2015-03-01

    The evaluation of the status of shallow magma body (i.e., from the final intrusion stage, to quiescence, and back to activity), one of the key parameters that trigger and sustain volcanic eruptions, has been challenging in modern volcanology. Among volatile tracers, chlorine (Cl) uniquely exsolves at shallow depths and is highly hydrophilic. Consequently, Cl enrichment in volcanic gases and thermal springs has been proposed as a sign for shallow magmatic activities. However, such enrichment could also result from numerous other processes (e.g., water evaporation, dissolution of old chloride mineral deposits, seawater contamination) that are unrelated to magmatic activity. Here, based on stable isotope compositions of chloride and dissolved inorganic carbon, as well as previous published 3He/4He data obtained in thermal springs from two recently erupted volcanoes (La Soufrière in Guadeloupe and Montagne Pelée in Martinique) in the Lesser Antilles Arc, we show that the magmatic Cl efficiently trapped in thermal springs displays negative δ37Cl values (≤ - 0.65 ‰), consistent with a slab-derived origin but distinct from the isotope compositions of chloride in surface reservoirs (e.g. seawater, local meteoric waters, rivers and cold springs) displaying common δ37Cl values of around 0‰. Using this δ37Cl difference as an index of magmatic Cl, we further examined thermal spring samples including a 30-year archive from two thermal springs in Guadeloupe covering samples from its last eruption in 1976-1977 to 2008 and an island-wide sampling event in Martinique in 2008 to trace the evolution of magmatic Cl in the volcanic hydrothermal systems over time. The results show that magmatic Cl can be rapidly flushed out of the hydrothermal systems within <30 to 80 years after the eruption, much quicker than other volatile tracers such as CO2 and noble gases, which can exsolve at greater depths and constantly migrate to the surface. Because arc volcanoes often have well

  4. External Thermal Insulation Composite Systems: Critical Parameters for Surface Hygrothermal Behaviour

    Directory of Open Access Journals (Sweden)

    Eva Barreira

    2014-01-01

    Full Text Available External Thermal Insulation Composite Systems (ETICS are often used in Europe. Despite its thermal advantages, low cost, and ease of application, this system has serious problems of biological growth causing the cladding defacement. Recent studies pointed that biological growth is due to high values of surface moisture content, which mostly results from the combined effect of exterior surface condensation, wind-driven rain, and drying process. Based on numerical simulation, this paper points the most critical parameters involved in hygrothermal behaviour of ETICS, considering the influence of thermal and hygric properties of the external rendering, the effect of the characteristics of the façade, and the consequences of the exterior and interior climate on exterior surface condensation, wind-driven rain, and drying process. The model used was previously validated by comparison with the results of an “in situ” campaign. The results of the sensitivity analyses show that relative humidity and temperature of the exterior air, atmospheric radiation, and emissivity of the exterior rendering are the parameters that most influence exterior surface condensation. Wind-driven rain depends mostly on horizontal rain, building’s height, wind velocity, and orientation. The drying capacity is influenced by short-wave absorbance, incident solar radiation, and orientation.

  5. Surface and thermal effects on vibration of embedded alumina nanobeams based on novel Timoshenko beam model

    Institute of Scientific and Technical Information of China (English)

    B AMIRIAN; R HOSSEINI-ARA; H MOOSAVI

    2014-01-01

    This paper deals with the free vibration analysis of circular alumina (Al2O3) nanobeams in the presence of surface and thermal effects resting on a Pasternak foun-dation. The system of motion equations is derived using Hamilton’s principle under the assumptions of the classical Timoshenko beam theory. The effects of the transverse shear deformation and rotary inertia are also considered within the framework of the mentioned theory. The separation of variables approach is employed to discretize the governing equa-tions which are then solved by an analytical method to obtain the natural frequencies of the alumina nanobeams. The results show that the surface effects lead to an increase in the natural frequency of nanobeams as compared with the classical Timoshenko beam model. In addition, for nanobeams with large diameters, the surface effects may increase the natural frequencies by increasing the thermal effects. Moreover, with regard to the Pasternak elastic foundation, the natural frequencies are increased slightly. The results of the present model are compared with the literature, showing that the present model can capture correctly the surface effects in thermal vibration of nanobeams.

  6. Surface modification of austenitic thermal-spray coatings by low-temperature nitrocarburizing

    Science.gov (United States)

    Lindner, T.; Mehner, T.; Lampke, T.

    2016-03-01

    Thermal-spray coatings of austenitic materials are mainly used under corrosive conditions. The relatively poor wear resistance strongly limits their use. In comparative studies between nitrocarburized and untreated thermal-spray coatings, the influence of the nitrogen and carbon enrichment on the properties of the coatings and the microstructure was investigated. The cross-section micrograph of the nitrocarburized coating shows the S-phase formation in the surface layer region. The depth profile of the nitrogen and carbon concentration was determined by glow discharge optical emission spectroscopy (GDOS) analysis. A selective enrichment of the surface layer region with nitrogen and carbon by means of thermochemical heat treatment increases the wear resistance. The interstitially dissolved nitrogen and carbon causes the formation of strong compressive residual stresses and high surface hardness. Increases in the service life of existing applications or new material combinations with face-centred cubic friction partners are possible. In the absence of dimensional change, uniform as well as partial nitrogen enrichment of the thermal spray coating is possible. Nitrocarburized coatings demonstrate a significant improvement in adhesive wear resistance and extremely high surface hardness.

  7. Facile synthesis of thermally stable poly(N-vinylpyrrolidone)-modified gold surfaces by surface-initiated atom transfer radical polymerization.

    Science.gov (United States)

    Liu, Xiaoli; Sun, Kai; Wu, Zhaoqiang; Lu, Jianhong; Song, Bo; Tong, Weifang; Shi, Xiujuan; Chen, Hong

    2012-06-26

    Well-controlled polymerization of N-vinylpyrrolidone (NVP) on Au surfaces by surface-initiated atom transfer radical polymerization (SI-ATRP) was carried out at room temperature by a silanization method. Initial attempts to graft poly(N-vinylpyrrolidone) (PVP) layers from initiators attached to alkanethiol monolayers yielded PVP films with thicknesses less than 5 nm. The combined factors of the difficulty in the controllable polymerization of NVP and the instability of alkanethiol monolayers led to the difficulty in the controlled polymerization of NVP on Au surfaces. Therefore, the silanization method was employed to form an adhesion layer for initiator attachment. This method allowed well-defined ATRP polymerization to occur on Au surfaces. Water contact angle, X-ray photoelectron spectroscopy (XPS), and reflectance Fourier transform infrared (reflectance FTIR) spectroscopy were used to characterize the modified surfaces. The PVP-modified gold surface remained stable at 130 °C for 3 h, showing excellent thermal stability. Thus, postfunctionalization of polymer brushes at elevated temperatures is made possible. The silanization method was also applied to modify SPR chips and showed potential applications in biosensors and biochips.

  8. A Multi-Channel Method for Retrieving Surface Temperature for High-Emissivity Surfaces from Hyperspectral Thermal Infrared Images

    Directory of Open Access Journals (Sweden)

    Xinke Zhong

    2015-06-01

    Full Text Available The surface temperature (ST of high-emissivity surfaces is an important parameter in climate systems. The empirical methods for retrieving ST for high-emissivity surfaces from hyperspectral thermal infrared (HypTIR images require spectrally continuous channel data. This paper aims to develop a multi-channel method for retrieving ST for high-emissivity surfaces from space-borne HypTIR data. With an assumption of land surface emissivity (LSE of 1, ST is proposed as a function of 10 brightness temperatures measured at the top of atmosphere by a radiometer having a spectral interval of 800–1200 cm−1 and a spectral sampling frequency of 0.25 cm−1. We have analyzed the sensitivity of the proposed method to spectral sampling frequency and instrumental noise, and evaluated the proposed method using satellite data. The results indicated that the parameters in the developed function are dependent on the spectral sampling frequency and that ST of high-emissivity surfaces can be accurately retrieved by the proposed method if appropriate values are used for each spectral sampling frequency. The results also showed that the accuracy of the retrieved ST is of the order of magnitude of the instrumental noise and that the root mean square error (RMSE of the ST retrieved from satellite data is 0.43 K in comparison with the AVHRR SST product.

  9. Thermal Tracking in Mobile Robots for Leak Inspection Activities

    Directory of Open Access Journals (Sweden)

    Iñaki Maurtua

    2013-10-01

    Full Text Available Maintenance tasks are crucial for all kind of industries, especially in extensive industrial plants, like solar thermal power plants. The incorporation of robots is a key issue for automating inspection activities, as it will allow a constant and regular control over the whole plant. This paper presents an autonomous robotic system to perform pipeline inspection for early detection and prevention of leakages in thermal power plants, based on the work developed within the MAINBOT (http://www.mainbot.eu European project. Based on the information provided by a thermographic camera, the system is able to detect leakages in the collectors and pipelines. Beside the leakage detection algorithms, the system includes a particle filter-based tracking algorithm to keep the target in the field of view of the camera and to avoid the irregularities of the terrain while the robot patrols the plant. The information provided by the particle filter is further used to command a robot arm, which handles the camera and ensures that the target is always within the image. The obtained results show the suitability of the proposed approach, adding a tracking algorithm to improve the performance of the leakage detection system.

  10. Thermally activated charge transport in microbial protein nanowires.

    Science.gov (United States)

    Lampa-Pastirk, Sanela; Veazey, Joshua P; Walsh, Kathleen A; Feliciano, Gustavo T; Steidl, Rebecca J; Tessmer, Stuart H; Reguera, Gemma

    2016-03-24

    The bacterium Geobacter sulfurreducens requires the expression of conductive protein filaments or pili to respire extracellular electron acceptors such as iron oxides and uranium and to wire electroactive biofilms, but the contribution of the protein fiber to charge transport has remained elusive. Here we demonstrate efficient long-range charge transport along individual pili purified free of metal and redox organic cofactors at rates high enough to satisfy the respiratory rates of the cell. Carrier characteristics were within the orders reported for organic semiconductors (mobility) and inorganic nanowires (concentration), and resistivity was within the lower ranges reported for moderately doped silicon nanowires. However, the pilus conductance and the carrier mobility decreased when one of the tyrosines of the predicted axial multistep hopping path was replaced with an alanine. Furthermore, low temperature scanning tunneling microscopy demonstrated the thermal dependence of the differential conductance at the low voltages that operate in biological systems. The results thus provide evidence for thermally activated multistep hopping as the mechanism that allows Geobacter pili to function as protein nanowires between the cell and extracellular electron acceptors.

  11. Thermal tracking in mobile robots for leak inspection activities.

    Science.gov (United States)

    Ibarguren, Aitor; Molina, Jorge; Susperregi, Loreto; Maurtua, Iñaki

    2013-10-09

    Maintenance tasks are crucial for all kind of industries, especially in extensive industrial plants, like solar thermal power plants. The incorporation of robots is a key issue for automating inspection activities, as it will allow a constant and regular control over the whole plant. This paper presents an autonomous robotic system to perform pipeline inspection for early detection and prevention of leakages in thermal power plants, based on the work developed within the MAINBOT (http://www.mainbot.eu) European project. Based on the information provided by a thermographic camera, the system is able to detect leakages in the collectors and pipelines. Beside the leakage detection algorithms, the system includes a particle filter-based tracking algorithm to keep the target in the field of view of the camera and to avoid the irregularities of the terrain while the robot patrols the plant. The information provided by the particle filter is further used to command a robot arm, which handles the camera and ensures that the target is always within the image. The obtained results show the suitability of the proposed approach, adding a tracking algorithm to improve the performance of the leakage detection system.

  12. A militarily fielded thermal neutron activation sensor for landmine detection

    Energy Technology Data Exchange (ETDEWEB)

    Clifford, E.T.H. [Bubble Technology Industries, Chalk River (Canada); McFee, J.E. [Defence R and D Canada-Suffield, Medicine Hat (Canada)], E-mail: john.mcfee@drdc-rddc.gc.ca; Ing, H.; Andrews, H.R.; Tennant, D.; Harper, E. [Bubble Technology Industries, Chalk River (Canada); Faust, A.A. [Defence R and D Canada-Suffield, Medicine Hat (Canada)

    2007-08-21

    The Canadian Department of National Defence has developed a teleoperated, vehicle-mounted, multi-sensor system to detect anti-tank landmines on roads and tracks in peacekeeping operations. A key part of the system is a thermal neutron activation (TNA) sensor which is placed above a suspect location to within a 30 cm radius and confirms the presence of explosives via detection of the 10.835 MeV gamma ray associated with thermal neutron capture on {sup 14}N. The TNA uses a 100{mu}g{sup 252}Cf neutron source surrounded by four 7.62cmx7.62cm NaI(Tl) detectors. The system, consisting of the TNA sensor head, including source, detectors and shielding, the high-rate, fast pulse processing electronics and the data processing methodology are described. Results of experiments to characterize detection performance are also described. The experiments have shown that anti-tank mines buried 10 cm or less can be detected in roughly a minute or less, but deeper mines and mines significantly displaced horizontally take considerably longer time. Mines as deep as 30 cm can be detected for long count times (1000 s). Four TNA detectors are now in service with the Canadian Forces as part of the four multi-sensor systems, making it the first militarily fielded TNA sensor and the first militarily fielded confirmation sensor for landmines. The ability to function well in adverse climatic conditions has been demonstrated, both in trials and operations.

  13. H2S-mediated thermal and photochemical methane activation.

    Science.gov (United States)

    Baltrusaitis, Jonas; de Graaf, Coen; Broer, Ria; Patterson, Eric V

    2013-12-02

    Sustainable, low-temperature methods for natural gas activation are critical in addressing current and foreseeable energy and hydrocarbon feedstock needs. Large portions of natural gas resources are still too expensive to process due to their high content of hydrogen sulfide gas (H2S) mixed with methane, deemed altogether as sub-quality or "sour" gas. We propose a unique method of activation to form a mixture of sulfur-containing hydrocarbon intermediates, CH3SH and CH3SCH3 , and an energy carrier such as H2. For this purpose, we investigated the H2S-mediated methane activation to form a reactive CH3SH species by means of direct photolysis of sub-quality natural gas. Photoexcitation of hydrogen sulfide in the CH4 + H2S complex resulted in a barrierless relaxation by a conical intersection to form a ground-state CH3SH + H2 complex. The resulting CH3SH could further be coupled over acidic catalysts to form higher hydrocarbons, and the resulting H2 used as a fuel. This process is very different from conventional thermal or radical-based processes and can be driven photolytically at low temperatures, with enhanced control over the conditions currently used in industrial oxidative natural gas activation. Finally, the proposed process is CO2 neutral, as opposed to the current industrial steam methane reforming (SMR).

  14. Tables for simplifying calculations of activities produced by thermal neutrons

    Science.gov (United States)

    Senftle, F.E.; Champion, W.R.

    1954-01-01

    The method of calculation described is useful for the types of work of which examples are given. It is also useful in making rapid comparison of the activities that might be expected from several different elements. For instance, suppose it is desired to know which of the three elements, cobalt, nickel, or vanadium is, under similar conditions, activated to the greatest extent by thermal neutrons. If reference is made to a cross-section table only, the values may be misleading unless properly interpreted by a suitable comparison of half-lives and abundances. In this table all the variables have been combined and the desired information can be obtained directly from the values of A 3??, the activity produced per gram per second of irradiation, under the stated conditions. Hence, it is easily seen that, under similar circumstances of irradiation, vanadium is most easily activated even though the cross section of one of the cobalt isotopes is nearly five times that of vanadium and the cross section of one of the nickel isotopes is three times that of vanadium. ?? 1954 Societa?? Italiana di Fisica.

  15. Application of remote sensing to thermal pollution analysis. [satellite sea surface temperature measurement assessment

    Science.gov (United States)

    Hiser, H. W.; Lee, S. S.; Veziroglu, T. N.; Sengupta, S.

    1975-01-01

    A comprehensive numerical model development program for near-field thermal plume discharge and far field general circulation in coastal regions is being carried on at the University of Miami Clean Energy Research Institute. The objective of the program is to develop a generalized, three-dimensional, predictive model for thermal pollution studies. Two regions of specific application of the model are the power plants sites at the Biscayne Bay and Hutchinson Island area along the Florida coastline. Remote sensing from aircraft as well as satellites are used in parallel with in situ measurements to provide information needed for the development and verification of the mathematical model. This paper describes the efforts that have been made to identify problems and limitations of the presently available satellite data and to develop methods for enhancing and enlarging thermal infrared displays for mesoscale sea surface temperature measurements.

  16. Thermally driven transverse transports and magnetic dynamics on a topological surface capped with a ferromagnet strip

    Science.gov (United States)

    Deng, Ming-Xun; Zhong, Ming; Zheng, Shi-Han; Qiu, Jian-Ming; Yang, Mou; Wang, Rui-Qiang

    2016-02-01

    We theoretically study thermally driven transport of the Dirac fermions on the surface of a topological insulator capped with a ferromagnet strip. The generation and manipulation of anomalous Hall and Nernst effects are analyzed, in which the in-plane magnetization of the ferromagnet film is found to take a decisive role. This scenario is distinct from that modulated by Berry phase where the in-plane magnetization is independent. We further discuss the thermal spin-transfer torque as a backaction of the thermoelectric transports on the magnetization and calculate the dynamics of the anomalous Hall and Nernst effects self-consistently. It is found that the magnitude of the long-time steady Hall and Nernst conductance is determined by competition between the magnetic anisotropy and current-induced effective anisotropy. These results open up a possibility of magnetically controlling the transverse thermoelectric transports or thermally manipulating the magnet switching.

  17. Modification of a metallic surface in a vacuum arc discharge plasma using thermally stimulated ion diffusion

    Science.gov (United States)

    Muboyadzhyan, S. A.

    2008-12-01

    A new process for modifying a metallic surface in a vacuum arc discharge plasma using thermally stimulated ion diffusion is considered. The effect of the bias voltage (negative substrate potential) on the processes that occur on the surface of a treated part is studied when the substrate material interacts with an accelerated metallic-ion flow. The phase and elemental compositions of the modified layer are studied for substrates made of nickel-based superalloys, austenitic and martensitic steels, and titanium-based alloys. The heat resistance, the salt corrosion resistance, and the corrosion cracking resistance of steels and titanium-based alloys are investigated after their modification in vacuum arc plasmas of pure metals (Ti, Zr, Al, Cr, Y) and related alloys. The surface modification caused by the thermally stimulated ion saturation of the surfaces of parts made from structural materials is shown to change the structural-phase states of their surfaces and, correspondingly, the properties of these materials in relation to the state of the surface.

  18. Recent advances in organic thermally activated delayed fluorescence materials.

    Science.gov (United States)

    Yang, Zhiyong; Mao, Zhu; Xie, Zongliang; Zhang, Yi; Liu, Siwei; Zhao, Juan; Xu, Jiarui; Chi, Zhenguo; Aldred, Matthew P

    2017-02-06

    Organic materials that exhibit thermally activated delayed fluorescence (TADF) are an attractive class of functional materials that have witnessed a booming development in recent years. Since Adachi et al. reported high-performance TADF-OLED devices in 2012, there have been many reports regarding the design and synthesis of new TADF luminogens, which have various molecular structures and are used for different applications. In this review, we summarize and discuss the latest progress concerning this rapidly developing research field, in which the majority of the reported TADF systems are discussed, along with their derived structure-property relationships, TADF mechanisms and applications. We hope that such a review provides a clear outlook of these novel functional materials for a broad range of scientists within different disciplinary areas and attracts more researchers to devote themselves to this interesting research field.

  19. Stacking transition in bilayer graphene caused by thermally activated rotation

    Science.gov (United States)

    Zhu, Mengjian; Ghazaryan, Davit; Son, Seok-Kyun; Woods, Colin R.; Misra, Abhishek; He, Lin; Taniguchi, Takashi; Watanabe, Kenji; Novoselov, Kostya S.; Cao, Yang; Mishchenko, Artem

    2017-03-01

    Crystallographic alignment between two-dimensional crystals in van der Waals heterostructures brought a number of profound physical phenomena, including observation of Hofstadter butterfly and topological currents, and promising novel applications, such as resonant tunnelling transistors. Here, by probing the electronic density of states in graphene using graphene-hexagonal boron nitride-graphene tunnelling transistors, we demonstrate a structural transition of bilayer graphene from incommensurate twisted stacking state into a commensurate AB stacking due to a macroscopic graphene self-rotation. This structural transition is accompanied by a topological transition in the reciprocal space and by pseudospin texturing. The stacking transition is driven by van der Waals interaction energy of the two graphene layers and is thermally activated by unpinning the microscopic chemical adsorbents which are then removed by the self-cleaning of graphene.

  20. Influence of soil moisture content on surface albedo and soil thermal parameters at a tropical station

    Science.gov (United States)

    Sugathan, Neena; Biju, V.; Renuka, G.

    2014-06-01

    Half hourly data of soil moisture content, soil temperature, solar irradiance, and reflectance are measured during April 2010 to March 2011 at a tropical station, viz., Astronomical Observatory, Thiruvananthapuram, Kerala, India (76°59'E longitude and 8°29'N latitude). The monthly, seasonal and seasonal mean diurnal variation of soil moisture content is analyzed in detail and is correlated with the rainfall measured at the same site during the period of study. The large variability in the soil moisture content is attributed to the rainfall during all the seasons and also to the evaporation/movement of water to deeper layers. The relationship of surface albedo on soil moisture content on different time scales are studied and the influence of solar elevation angle and cloud cover are also investigated. Surface albedo is found to fall exponentially with increase in soil moisture content. Soil thermal diffusivity and soil thermal conductivity are also estimated from the subsoil temperature profile. Log normal dependence of thermal diffusivity and power law dependence of thermal conductivity on soil moisture content are confirmed.

  1. Influence of soil moisture content on surface albedo and soil thermal parameters at a tropical station

    Indian Academy of Sciences (India)

    Neena Sugathan; V Biju; G Renuka

    2014-07-01

    Half hourly data of soil moisture content, soil temperature, solar irradiance, and reflectance are measured during April 2010 to March 2011 at a tropical station, viz., Astronomical Observatory, Thiruvananthapuram, Kerala, India (76° 59’E longitude and 8°29’N latitude). The monthly, seasonal and seasonal mean diurnal variation of soil moisture content is analyzed in detail and is correlated with the rainfall measured at the same site during the period of study. The large variability in the soil moisture content is attributed to the rainfall during all the seasons and also to the evaporation/movement of water to deeper layers. The relationship of surface albedo on soil moisture content on different time scales are studied and the influence of solar elevation angle and cloud cover are also investigated. Surface albedo is found to fall exponentially with increase in soil moisture content. Soil thermal diffusivity and soil thermal conductivity are also estimated from the subsoil temperature profile. Log normal dependence of thermal diffusivity and power law dependence of thermal conductivity on soil moisture content are confirmed.

  2. Phonon surface scattering controlled length dependence of thermal conductivity of silicon nanowires.

    Science.gov (United States)

    Xie, Guofeng; Guo, Yuan; Li, Baohua; Yang, Liwen; Zhang, Kaiwang; Tang, Minghua; Zhang, Gang

    2013-09-21

    We present a kinetic model to investigate the anomalous thermal conductivity in silicon nanowires (SiNWs) by focusing on the mechanism of phonon-boundary scattering. Our theoretical model takes into account the anharmonic phonon-phonon scattering and the angle-dependent phonon scattering from the SiNWs surface. For SiNWs with diameter of 27.2 nm, it is found that in the case of specular reflection at lateral boundaries, the thermal conductivity increases as the length increases, even when the length is up to 10 μm, which is considerably longer than the phonon mean free path (MFP). Thus the phonon-phonon scattering alone is not sufficient for obtaining a normal diffusion in nanowires. However, in the case of purely diffuse reflection at lateral boundaries, the phonons diffuse normally and the thermal conductivity converges to a constant when the length of the nanowire is greater than 100 nm. Our model demonstrates that for observing the length dependence of thermal conductivity experimentally, nanowires with smooth and non-contaminated surfaces, and measuring at low temperature, are preferred.

  3. Non-Thermal Effects on CO-NO Surface Catalytic Reaction on Square Surface: Monte Carlo Study

    Institute of Scientific and Technical Information of China (English)

    M. Khalid; A. U. Qaisrani; W. Ahmad

    2005-01-01

    @@ A Monte Carlo simulation of the CO-NO heterogeneous catalytic reaction over a square surface has already been studied with a model based on the Langmuir-Hinshelwood (LH) mechanism. The results of this study are well known. Here we study the effects of transient non-thermal mobility of monomer (CO) based on precursor mechanism, diffusion of adsorbed nitrogen and oxygen atoms, on the phase diagram. The interesting feature of this model is the yield of a steady reactiw window, while simple LH mechanism is not capable of producing a steady reactive state.

  4. Whisker/Cone growth on the thermal control surfaces experiment no. S0069

    Science.gov (United States)

    Zwiener, James M.; Coston, James E., Jr.; Miller, Edgar R.; Mell, Richard J.; Wilkes, Donald R.

    1995-01-01

    An unusual surface 'growth' was found during scanning electron microscope (SEM) investigations of the Thermal Control Surface Experiment (TCSE) S0069 front thermal cover. This 'growth' is similar to the cone type whisker growth phenomena as studied by G. K. Wehner beginning in the 1960's. Extensive analysis has identified the most probable composition of the whiskers to be a silicate type glass. Sources of the growth material are outgassing products from the experiment and orbital atomic oxygen, which occurs naturally at the orbital altitudes of the LDEF mission in the form of neutral atomic oxygen. The highly ordered symmetry and directionality of the whiskers are attributed to the long term (5.8 year) stable flight orientation of the LDEF.

  5. Investigation of thermal effect on exterior wall surface of building material at urban city area

    Directory of Open Access Journals (Sweden)

    Mohd Fadhil Md Din, Hazlini Dzinun, M. Ponraj, Shreeshivadasan Chelliapan, Zainura Zainun Noor, Dilshah Remaz, Kenzo Iwao

    2012-01-01

    Full Text Available This paper describes the investigation of heat impact on the vertical surfaces of buildings based on their thermal behavior. The study was performed based on four building materials that is commonly used in Malaysia; brick, concrete, granite and white concrete tiles. The thermal performances on the building materials were investigated using a surface temperature sensor, data logging system and infrared thermography. Results showed that the brick had the capability to absorb and store heat greater than other materials during the investigation period. The normalized heat (total heat/solar radiation of the brick was 0.093 and produces high heat (51% compared to granite, confirming a substantial amount of heat being released into the atmosphere through radiation and convection. The most sensitive material that absorbs and stores heat was in the following order: brick > concrete > granite > white concrete tiles. It was concluded that the type of exterior wall material used in buildings had significant impact to the environment.

  6. Investigation of thermal effect on exterior wall surface of building material at urban city area

    Energy Technology Data Exchange (ETDEWEB)

    Md Din, Mohd Fadhil; Dzinun, Hazlini; Ponraj, M.; Chelliapan, Shreeshivadasan; Noor, Zainura Zainun [Institute of Environmental Water Resources and Management (IPASA), Faculty of Civil Engineering, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia); Remaz, Dilshah [Faculty of Built Environment, Universiti Teknologi Malaysia, 81310 UTM Skudai, Johor (Malaysia); Iwao, Kenzo [Nagoya Institute of Technology, Nagoya (Japan)

    2012-07-01

    This paper describes the investigation of heat impact on the vertical surfaces of buildings based on their thermal behavior. The study was performed based on four building materials that is commonly used in Malaysia; brick, concrete, granite and white concrete tiles. The thermal performances on the building materials were investigated using a surface temperature sensor, data logging system and infrared thermography. Results showed that the brick had the capability to absorb and store heat greater than other materials during the investigation period. The normalized heat (total heat/solar radiation) of the brick was 0.093 and produces high heat (51% compared to granite), confirming a substantial amount of heat being released into the atmosphere through radiation and convection. The most sensitive material that absorbs and stores heat was in the following order: brick > concrete > granite > white concrete tiles. It was concluded that the type of exterior wall material used in buildings had significant impact to the environment.

  7. Electrochemical and thermal grafting of alkyl grignard reagents onto (100) silicon surfaces.

    Science.gov (United States)

    Vegunta, Sri Sai S; Ngunjiri, Johnpeter N; Flake, John C

    2009-11-03

    Passivation of (100) silicon surfaces using alkyl Grignard reagents is explored via electrochemical and thermal grafting methods. The electrochemical behavior of silicon in methyl or ethyl Grignard reagents in tetrahydrofuran is investigated using cyclic voltammetry. Surface morphology and chemistry are investigated using atomic force microscopy, Fourier transform infrared spectroscopy, and X-ray photoelectron spectroscopy (XPS). Results show that electrochemical pathways provide an efficient and more uniform passivation method relative to thermal methods, and XPS results demonstrate that electrografted terminations are effective at limiting native oxide formation for more than 55 days in ambient conditions. A two-electron per silicon mechanism is proposed for electrografting a single (1:1) alkyl group per (100) silicon atom. The mechanism includes oxidation of two Grignard species and subsequent hydrogen abstraction and alkylation reaction resulting in a covalent attachment of alkyl groups with silicon.

  8. Design and construction of a compact module of surfaces treatment by thermal shock

    Energy Technology Data Exchange (ETDEWEB)

    Sylvester, G.; Zambra, M.; Soto, L. [Comision Chilena de Energia Nuclear, Casilla 188 D, Santiago (Chile); Feugeas, J.; Clausse, A.; Bruzzone, H. [Red Interinstitucional de Plasmas Densos y Magnetizados (PLADEMA) (Argentina)

    2002-07-01

    Research on surfaces treatment by thermal shock is currently being pursued at The Institute of Physics of the University of Rosario (IFUR), using plasma focus systems. Thus, the effect of the thermal shock, due to the incidence of highly energetic, short duration, plasma beams, on metallic surfaces, offers interesting possibilities for application in steels, increasing their resistance to the wear and microhardness. This work addresses the design and construction of a compact plasma focus module (30x30xl00 cm{sup 3}), generating pulses of ions, with a duration of 200 to 500 nanoseconds and an emission frequency under 10 Hz. The energy deposited is 10 J at a fluence of 10{sup 13} cm{sup -2} per pulse. (Author)

  9. Numerical modeling for analyzing thermal surface anomalies induced by underground coal fires

    Energy Technology Data Exchange (ETDEWEB)

    Wessling, Stefan; Kessels, Winfried; Wuttke, Manfred W. [Leibniz Institute for Applied Geosciences, Stilleweg 2, D-30655 Hannover (Germany); Kuenzer, Claudia [Institute of Photogrammetry and Remote Sensing, IPF, Vienna University of Technology, Gusshausstr. 27-29, A-1040 Wien (Austria)

    2008-05-07

    Coal seams burning underneath the surface are recognized all over the world and have drawn increasing public attention in the past years. Frequently, such fires are analyzed by detecting anomalies like increased exhaust gas concentrations and soil temperatures at the surface. A proper analysis presumes the understanding of involved processes, which determine the spatial distribution and dynamic behavior of the anomalies. In this paper, we explain the relevance of mechanical and energy transport processes with respect to the occurrence of temperature anomalies at the surface. Two approaches are presented, aiming to obtain insight into the underground coal fire situation: In-situ temperature mapping and numerical simulation. In 2000 to 2005, annual temperature mapping in the Wuda (Inner Mongolia, PR China) coal fire area showed that most thermal anomalies on the surface are closely related to fractures, where hot exhaust gases from the coal fire are released. Those fractures develop due to rock mechanical failure after volume reduction in the seams. The measured signals at the surface are therefore strongly affected by mechanical processes. More insight into causes and effects of involved energy transport processes is obtained by numerical simulation of the dynamic behavior of coal fires. Simulations show the inter-relation between release and transport of thermal energy in and around underground coal fires. Our simulation results show a time delay between the coal fire propagation and the observed appearance of the surface temperature signal. Additionally, the overall energy flux away from the burning coal seam into the surrounding bedrock is about 30-times higher than the flux through the surface. This is of particular importance for an estimation of the energy released based on surface temperature measurements. Finally, the simulation results also prove that a fire propagation rate estimated from the interpretation of surface anomalies can differ from the actual

  10. Detecting urbanization effects on surface and subsurface thermal environment--a case study of Osaka.

    Science.gov (United States)

    Huang, Shaopeng; Taniguchi, Makoto; Yamano, Makoto; Wang, Chung-ho

    2009-04-15

    Tremendous efforts have been devoted to improve our understanding of the anthropogenic effects on the atmospheric temperature change. In comparison, little has been done in the study of the human impacts on the subsurface thermal environment. The objective of this study is to analyze surface air temperature records and borehole subsurface temperature records for a better understanding of the urban heat island effects across the ground surface. The annual surface air temperature time series from six meteorological stations and six deep borehole temperature profiles of high qualities show that Osaka has been undergoing excess warming since late 19th century. The mean warming rate in Osaka surface air temperature is about 2.0 degrees C/100a over the period from 1883 to 2006, at least half of which can be attributed to the urban heat island effects. However, this surface air temperature warming is not as strong as the ground warming recorded in the subsurface temperature profiles. The surface temperature anomaly from the Osaka meteorological record can only account for part of the temperature anomaly recorded in the borehole temperature profiles. Surface air temperature is conventionally measured around 1.5 m above the ground; whereas borehole temperatures are measured from rocks in the subsurface. Heat conduction in the subsurface is much less efficient than the heat convection of the air above the ground surface. Therefore, the anthropogenic thermal impacts on the subsurface can be more persistent and profound than the impacts on the atmosphere. This study suggests that the surface air temperature records alone might underestimate the full extent of urban heat island effects on the subsurface environment.

  11. Thermal dynamics-based mechanism for intense laser-induced material surface vaporization

    Indian Academy of Sciences (India)

    N Kumar; S Dash; A K Tyagi; Baldev Raj

    2008-09-01

    Laser material processing involving welding, ablation and cutting involves interaction of intense laser pulses of nanosecond duration with a condensed phase. Such interaction involving high brightness radiative flux causes multitude of non-linear events involving thermal phase transition at soild–liquid–gas interfaces. A theoretical perspective involving thermal dynamics of the vaporization process and consequent non-linear multiple thermal phase transitions under the action of laser plasma is the subject matter of the present work. The computational calculations were carried out where titanium (Ti) was treated as a condensed medium. The solution to the partial differential equations governing the thermal dynamics and the underlying phase transition event in the multiphase system is based on non-stationary Eulerian variables. The Mach number depicts significant fluctuations due to thermal instabilities associated with the laser beam flux and intensity. A conclusive amalgamation has been established which relates material surface temperature profile to laser intensity, laser flux and the pressure in the plasma cloud.

  12. Active Aerothermoelastic Control of Hypersonic Double-wedge Lifting Surface

    Institute of Scientific and Technical Information of China (English)

    Laith K Abbas; Chen Qian; Piergiovanni Marzocca; Gürdal Zafer; Abdalla Mostafa

    2008-01-01

    Designing reentry space vehicles and high-speed aireraft requires special attention to the nonlinear thermoelastic and aerodynamic instability of their structural components. The thermal effects are important since temperature environment brings dramatic influences on the static and dynamic behaviors of flight structures in supersonic/hypersonic regimes and is likely to cause instability, catastrophic failure and oscillations resulting in structural failure due to fatigue. In order to understand the dynamic behaviors of these "hot"structures, a double-wedge lifting surface with combining freeplay and cubic structural nonlinearities in both plunging and pitching degrees-of-freedom operating in supersonic/hypersonic flight speed regimes has been analyzed. A third order piston theory aerodynamic isused to estimate the applied nonlinear unsteady aerodynamic loads. Also considered is the loss of torsiunal stiffness that may be incurredby lifting surfaces subject to axial stresses induced by aerodynamic heating. The aerodynamic heating effects are estimated based on theadiabatic wall temperature due to high speed airstreams. As a recently emerging technology, the active aerothermoelastic control isaimed at providing solutions to a large number of problems involving the aeronautica Faerospace flight vehicle structures. To preventsuch damaging phenomena from occurring, an application of linear and nonlinear active control methods on both flutter boundary andpost-flutter behavior has been fulfilled. In this paper, modeling issues as well as numerical simulation have been presented and pertinent conclusions outlined. It is evidenced that a serious loss of torsional stiffness may induce the dynamic instability; however active controlcan be used to expand the flutter boundary and convert unstable limit cycle oscillations (LCO) into the stable LCO and/or to shift the transition between these two states toward higher flight Mach numbers.

  13. Corrugated paraffin nanocomposite films as large stroke thermal actuators and self-activating thermal interfaces.

    Science.gov (United States)

    Copic, Davor; Hart, A John

    2015-04-22

    High performance active materials are of rapidly growing interest for applications including soft robotics, microfluidic systems, and morphing composites. In particular, paraffin wax has been used to actuate miniature pumps, solenoid valves, and composite fibers, yet its deployment is typically limited by the need for external volume constraint. We demonstrate that compact, high-performance paraffin actuators can be made by confining paraffin within vertically aligned carbon nanotube (CNT) films. This large-stroke vertical actuation is enabled by strong capillary interaction between paraffin and CNTs and by engineering the CNT morphology by mechanical compression before capillary-driven infiltration of the molten paraffin. The maximum actuation strain of the corrugated CNT-paraffin films (∼0.02-0.2) is comparable to natural muscle, yet the maximum stress is limited to ∼10 kPa by collapse of the CNT network. We also show how a CNT-paraffin film can serve as a self-activating thermal interface that closes a gap when it is heated. These new CNT-paraffin film actuators could be produced by large-area CNT growth, infiltration, and lamination methods, and are attractive for use in miniature systems due to their self-contained design.

  14. Retrieving Land Surface Temperature and Emissivity from Multispectral and Hyperspectral Thermal Infrared Instruments

    Science.gov (United States)

    Hook, Simon; Hulley, Glynn; Nicholson, Kerry

    2017-04-01

    Land Surface Temperature and Emissivity (LST&E) data are critical variables for studying a variety of Earth surface processes and surface-atmosphere interactions such as evapotranspiration, surface energy balance and water vapor retrievals. LST&E have been identified as an important Earth System Data Record (ESDR) by NASA and many other international organizations Accurate knowledge of the LST&E is a key requirement for many energy balance models to estimate important surface biophysical variables such as evapotranspiration and plant-available soil moisture. LST&E products are currently generated from sensors in low earth orbit (LEO) such as the NASA Moderate Resolution Imaging Spectroradiometer (MODIS) instruments on the Terra and Aqua satellites as well as from sensors in geostationary Earth orbit (GEO) such as the Geostationary Operational Environmental Satellites (GOES) and airborne sensors such as the Hyperspectral Thermal Emission Spectrometer (HyTES). LST&E products are generated with varying accuracies depending on the input data, including ancillary data such as atmospheric water vapor, as well as algorithmic approaches. NASA has identified the need to develop long-term, consistent, and calibrated data and products that are valid across multiple missions and satellite sensors. We will discuss the different approaches that can be used to retrieve surface temperature and emissivity from multispectral and hyperspectral thermal infrared sensors using examples from a variety of different sensors such as those mentioned, and planned new sensors like the ECOsystem Spaceborne Thermal Radiometer Experiment on Space Station (ECOSTRESS) and the Hyperspectral Infrared Imager (HyspIRI). We will also discuss a project underway at NASA to develop a single unified product from some the individual sensor products and assess the errors associated with the product.

  15. Quantifying riverine surface currents from time sequences of thermal infrared imagery

    Science.gov (United States)

    Puleo, J.A.; McKenna, T.E.; Holland, K.T.; Calantoni, J.

    2012-01-01

    River surface currents are quantified from thermal and visible band imagery using two methods. One method utilizes time stacks of pixel intensity to estimate the streamwise velocity at multiple locations. The other method uses particle image velocimetry to solve for optimal two-dimensional pixel displacements between successive frames. Field validation was carried out on the Wolf River, a small coastal plain river near Landon, Mississippi, United States, on 26-27 May 2010 by collecting imagery in association with in situ velocities sampled using electromagnetic current meters deployed 0.1 m below the river surface. Comparisons are made between mean in situ velocities and image-derived velocities from 23 thermal and 6 visible-band image sequences (5 min length) during daylight and darkness conditions. The thermal signal was a small apparent temperature contrast induced by turbulent mixing of a thin layer of cooler water near the river surface with underlying warmer water. The visible-band signal was foam on the water surface. For thermal imagery, streamwise velocities derived from the pixel time stack and particle image velocimetry technique were generally highly correlated to mean streamwise current meter velocities during darkness (r 2 typically greater than 0.9) and early morning daylight (r 2 typically greater than 0.83). Streamwise velocities from the pixel time stack technique had high correlation for visible-band imagery during early morning daylight hours with respect to mean current meter velocities (r 2 > 0.86). Streamwise velocities for the particle image velocimetry technique for visible-band imagery had weaker correlations with only three out of six correlations performed having an r 2 exceeding 0.6. Copyright 2012 by the American Geophysical Union.

  16. Thermally induced stresses in boulders on airless body surfaces, and implications for rock breakdown

    Science.gov (United States)

    Molaro, J. L.; Byrne, S.; Le, J.-L.

    2017-09-01

    This work investigates the macroscopic thermomechanical behavior of lunar boulders by modeling their response to diurnal thermal forcing. Our results reveal a bimodal, spatiotemporally-complex stress response. During sunrise, stresses occur in the boulders' interiors that are associated with large-scale temperature gradients developed due to overnight cooling. During sunset, stresses occur at the boulders' exteriors due to the cooling and contraction of the surface. Both kinds of stresses are on the order of 10 MPa in 1 m boulders and decrease for smaller diameters, suggesting that larger boulders break down more quickly. Boulders ≤ 30 cm exhibit a weak response to thermal forcing, suggesting a threshold below which crack propagation may not occur. Boulders of any size buried by regolith are shielded from thermal breakdown. As boulders increase in size (>1 m), stresses increase to several 10 s of MPa as the behavior of their surfaces approaches that of an infinite halfspace. As the thermal wave loses contact with the boulder interior, stresses become limited to the near-surface. This suggests that the survival time of a boulder is not only controlled by the amplitude of induced stress, but also by its diameter as compared to the diurnal skin depth. While stresses on the order of 10 MPa are enough to drive crack propagation in terrestrial environments, crack propagation rates in vacuum are not well constrained. We explore the relationship between boulder size, stress, and the direction of crack propagation, and discuss the implications for the relative breakdown rates and estimated lifetimes of boulders on airless body surfaces.

  17. Thermally Activated Palm Kernel Based Carbon as a Support for Edible Oil Hydrogenation Catalyst

    Directory of Open Access Journals (Sweden)

    Abdulmajid Alshaibani

    2013-01-01

    Full Text Available Activated carbon has distinctive properties as a support for hydrogenation catalysts. Thermally activated carbon has been prepared from palm kernel shell at 1073 K and placed under nitrogen flow for 2 h. It was impregnated by palladium using toluene solution of Pd (acac2. The Pd/C was reduced using a water solution of potassium borohydride (KBH4. The Pd-B/C was characterized by the Brunauer-Emmett-Teller surface area analysis (BET, scanning electron microscopy (SEM, transmission electron microscopy (TEM and inductively-coupled plasma mass spectrometry (ICP-MS. Pd-B/C was applied for sunflower oil hydrogenation at a temperature of 373 K, hydrogen pressure of 413.5 kPa and agitation of 1400 rpm for 1 h. Pd-B/C noticeably exhibited a higher overall catalyst activity in comparison to some recently published palladium catalysts.

  18. Rejection of surface background in thermal detectors: The ABSuRD project

    Energy Technology Data Exchange (ETDEWEB)

    Canonica, L., E-mail: lucia.canonica@lngs.infn.it [INFN, Laboratori Nazionali del Gran Sasso, Assergi, AQ (Italy); Biassoni, M.; Brofferio, C. [Università di Milano Bicocca e INFN Sezione di Milano Bicocca, Milano (Italy); Bucci, C.; Calvano, S.; Di Vacri, M.L. [INFN, Laboratori Nazionali del Gran Sasso, Assergi, AQ (Italy); Goett, J. [Los Alamos National Laboratory, Los Alamos, NM (United States); Gorla, P. [INFN, Laboratori Nazionali del Gran Sasso, Assergi, AQ (Italy); Pavan, M. [Università di Milano Bicocca e INFN Sezione di Milano Bicocca, Milano (Italy); Yeh, M. [Brookhaven National Laboratory, Upton, NY (United States)

    2013-12-21

    Thermal detectors have recently achieved a leading role in the fields of Neutrinoless Double Beta Decay and Dark Matter searches thanks to their excellent energy resolution and to the wide choice of absorber materials. In these fields the background coming from surface contaminations is frequently dominant. ABSuRD (A Background Surface Rejection Detector) is a scintillation-based approach for tagging this type of background. We discuss the innovative application of this technique in non-scintillating bolometric detectors which will allow for a more favorable signal to background ratio.

  19. Thermal infrared remote sensing of surface features for renewable resource applications

    Science.gov (United States)

    Welker, J. E.

    1981-01-01

    The subjects of infrared remote sensing of surface features for renewable resource applications is reviewed with respect to the basic physical concepts involved at the Earth's surface and up through the atmosphere, as well as the historical development of satellite systems which produce such data at increasingly greater spatial resolution. With this general background in hand, the growth of a variety of specific renewable resource applications using the developing thermal infrared technology are discussed, including data from HCMM investigators. Recommendations are made for continued growth in this field of applications.

  20. Atmospheric correction of LANDSAT TM thermal band using surface energy balance

    Science.gov (United States)

    Vidal, Alain; Devaux-Ros, Claire; Moran, M. Susan

    1994-01-01

    Thermal infrared data of LANDSAT Thematic Mapper (TM) are hardly used, probably due to the difficulties met when trying to correct them for atmospheric effects. A method for correcting these data was designed, based on surface energy balance estimation of known wet and dry targets included in the TM image to be corrected. This method, only using the image itself and local meteorological data was tested and validated on various surfaces: agricultural, forest and rangeland. The root mean square error on corrected temperatures is on the order of 1C.

  1. Self-Healing Thermal Annealing: Surface Morphological Restructuring Control of GaN Nanorods

    Energy Technology Data Exchange (ETDEWEB)

    Conroy, Michele; Li, Haoning; Zubialevich, Vitaly Z.; Kusch, Gunnar; Schmidt, Michael; Collins, Timothy; Glynn, Colm; Martin, Robert W.; O’Dwyer, Colm; Morris, Michael D.; Holmes, Justin D.; Parbrook, Peter J.

    2016-12-07

    With advances in nanolithography and dry etching, top-down methods of nanostructuring have become a widely used tool for improving the efficiency of optoelectronics. These nano dimensions can offer various benefits to the device performance in terms of light extraction and efficiency, but often at the expense of emission color quality. Broadening of the target emission peak and unwanted yellow luminescence are characteristic defect-related effects due to the ion beam etching damage, particularly for III–N based materials. In this article we focus on GaN based nanorods, showing that through thermal annealing the surface roughness and deformities of the crystal structure can be “self-healed”. Correlative electron microscopy and atomic force microscopy show the change from spherical nanorods to faceted hexagonal structures, revealing the temperature-dependent surface morphology faceting evolution. The faceted nanorods were shown to be strain- and defect-free by cathodoluminescence hyperspectral imaging, micro-Raman, and transmission electron microscopy (TEM). In-situ TEM thermal annealing experiments allowed for real time observation of dislocation movements and surface restructuring observed in ex-situ annealing TEM sampling. This thermal annealing investigation gives new insight into the redistribution path of GaN material and dislocation movement post growth, allowing for improved understanding and in turn advances in optoelectronic device processing of compound semiconductors.

  2. Carbon nanotubes dispersed polymer nanocomposites: mechanical, electrical, thermal properties and surface morphology

    Indian Academy of Sciences (India)

    Nitin Sankar; Mamilla Nagarjun Reddy; R Krishna Prasad

    2016-02-01

    The various properties and surface morphology of the carbon nanotubes (CNTs) dispersed polydimethyl siloxane (PDMS) matrix were studied to determine their usefulness in various applications. The tensile strength, Young's modulus and electrical breakdown strength of CNT/polymer composites were 0.35MPa, 1.2MPa and 8.1 kV, respectively. The thermal conductivity and dielectric constant for the material having 4.28 wt% CNT were 0.225 W m−1 K−1 and 2.329, respectively. The CNT/polymer composites are promising functional composites with improved mechanical and electrical properties. The scanning electron microscope analysis of surface morphology of PDMS/CNT composite showed that the rough surface texture on nanocomposite has large surface area with circular pores. The Fourier transform infrared spectroscopy showed the functional groups present in polymer nanocomposite.

  3. [Research progress of thermal control system for extravehicular activity space suit].

    Science.gov (United States)

    Wu, Z Q; Shen, L P; Yuan, X G

    1999-08-01

    New research progress of thermal control system for oversea Extravehicular Activity (EVA) space suit is presented. Characteristics of several thermal control systems are analyzed in detail. Some research tendencies and problems are discussed, which are worthwhile to be specially noted. Finally, author's opinion about thermal control system in the future is put forward.

  4. GRID based Thermal Images Processing for volcanic activity monitoring

    Science.gov (United States)

    Mangiagli, S.; Coco, S.; Drago, L.; Laudani, A.,; Lodato, L.; Pollicino, G.; Torrisi, O.

    2009-04-01

    Since 2001, the Catania Section of the National Institute of Geophysics and Volcanology (INGV) has been running the video stations recording the volcanic activity of Mount Etna, Stromboli and the Fossa Crater of Vulcano island. The video signals of 11 video cameras (seven operating in the visible band and four in infrared) are sent in real time to INGV Control Centre where they are visualized on monitors and archived on a dedicated NAS storage. The video surveillance of the Sicilian volcanoes, situated near to densely populated areas, helps the volcanologists providing the Civil Protection authorities with updates in real time on the on-going volcanic activity. In particular, five video cameras are operating on Mt. Etna and they record the volcano from the south and east sides 24 hours a day. During emergencies, mobile video stations may also be used to better film the most important phases of the activity. Single shots are published on the Catania Section intranet and internet websites. On June 2006 a A 40 thermal camera was installed in Vulcano La Fossa Crater. The location was in the internal and opposite crater flank (S1), 400 m distant from the fumarole field. The first two-year of data on temperature distribution frequency were recorded with this new methodology of acquisition, and automatically elaborated by software at INGV Catania Section. In fact a dedicated software developed in IDL, denominated Volcano Thermo Analysis (VTA), was appositely developed in order to extract a set of important features, able to characterize with a good approssimation the volcanic activity. In particular the program first load and opportunely convert the thermal images, then according to the Region Of Interest (ROI) and the temperature ranges defined by the user provide to automatic spatial and statistic analysis. In addition the VTA is able to analysis all the temporal series of images available in order to achieve the time-event analysis and the dynamic of the volcanic

  5. Synthesis, thermal stability, and photocatalytic activity of nanocrystalline titanium carbide

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Youjian; Zhang, Hong [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou, Zhejiang 325027 (China); Ma, DeKun [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou, Zhejiang 325027 (China); Nanomaterials and Chemistry Key Laboratory, Advanced Materials Research Center of Wenzhou, Wenzhou University, Wenzhou, Zhejiang 325027 (China); Ma, Jianhua, E-mail: mjh820@ustc.edu [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou, Zhejiang 325027 (China); Nanomaterials and Chemistry Key Laboratory, Advanced Materials Research Center of Wenzhou, Wenzhou University, Wenzhou, Zhejiang 325027 (China); Ye, Hongnan; Qian, Gaojin; Ye, Yi [Oujiang College, Wenzhou University, Wenzhou, Zhejiang 325027 (China)

    2011-11-15

    Highlights: {yields} The synthesized temperature is lower than some conventional methods. {yields} These raw materials are safe; all manipulations are rather safe and convenient. {yields} The product exhibits photocatalytic activity in degradation of Rhodamine-B. -- Abstract: Titanium carbide (TiC) was prepared via one simple route by the reaction of metallic magnesium powders with titanium dioxide (TiO{sub 2}) and potassium acetate (CH{sub 3}COOK) in an autoclave at 600 {sup o}C and 8 h. Phase structure and morphology were characterized by X-ray powder diffraction (XRD) and Scanning electron microscopy (SEM). The results indicated that the product was cubic TiC, which consisted of particles with an average size of about 100 nm in diameter. The product was also studied by the thermogravimetric analysis (TGA) and its photocatalysis. It had good thermal stability and oxidation resistance below 350 {sup o}C in air. In addition, we discovered that the cubic TiC powders exhibited photocatalytic activity in degradation of Rhodamine-B (RhB) under 500 W mercury lamp light irradiation.

  6. Surface-effects-dominated thermal and mechanical responses of zinc oxide nanobelts

    Institute of Scientific and Technical Information of China (English)

    A.J.Kulkarni; M.Zhou

    2006-01-01

    Molecular dynamics(MD)simulations are carried out to characterize the mechanical and thermal responses of [ol(l)o]-oriented ZnO nanobelts with lateral dimensions of 21.22(A)×18.95(A),31.02(A)×29.42(A) and 40.81(A)×39.89(A) over the temperature range of 300-1000 K. The Young's modulus and thermal conductivity of the nanobelts are evaluated. Significant surface effects on properties due to the highsurface-to-volume ratios of the nanobelts are observed. For the mechanical response, surface-stress-induced internal stress plays an important role. For the thermal response, surface scattering of phonons dominates. Calculations show that the Young's modulus is higher than the corresponding value for bulk ZnO and decreases by~33%as the lateral dimensions increase from 21.22(A)×18.95(A) to 40.8l(A)×39.89(A).The thermal conductivity is one order of magnitude lower than the corresponding value for bulk ZnO single crystal and decreases with wire size. Specifically, the conductivity of the 21.22(A)×18.95(A) beltis approximately(31-18)% lower than that of the 40.81(A)×39.89(A) belt over the temperature range analyzed. A significant dependence of properties on temperature is also observed. with the Young's modulus decreasing on average by 12% and the conductivity decreasing by 50% as temperature increases from 300 K to 1000 K.

  7. [The present status and development of thermal control system of spacesuits for extravehicular activity].

    Science.gov (United States)

    Zhao, C Y; Sun, J B; Yuan, X G

    1999-04-01

    With the extension of extravehicular activity (EVA) duration, the need for more effective thermal control of EVA spacesuits is required. The specific schemes investigated in heat sink system for EVA are discussed, including radiator, ice storage, metal hydride heat pump, phase-change storage/radiator and sublimator. The importance and requirements of automatic thermal control for EVA are also discussed. Existed automatic thermal control for EVA are reviewed. Prospects of further developments of thermal control of spacesuits for EVA are proposed.

  8. Effect of Activation Energies on Thermal Explosion in the Interior of the Earth

    OpenAIRE

    Amos Oladele Popoola

    2011-01-01

    Problem statement: Literatures have shown that thermal processes in the interior of the earth and the classical thermal explosion are analogous and that combustion processes are characterized by ignition and explosion. The heat released during the thermal explosion that occurs in the interior of the earth requires more attention. Approach: The study investigated the role of activation energies ratio in the thermal explosion that occurs in the earth interior during gravitat...

  9. Nitrate reducing activity pervades surface waters during upwelling.

    Digital Repository Service at National Institute of Oceanography (India)

    Fernandes, S.O.; Halarnekar, R.; Malik, A.; Vijayan, V.; Varik, S.; RituKumari; Jineesh V.K.; Gauns, M.U.; Nair, S.; LokaBharathi, P.A.

    Nitrate reducing activity (NRA) is known to be mediated by microaerophilic to anaerobic bacteria and generally occurs in the sub-surface waters. However, we hypothesize that NRA could become prominent in the surface waters during upwelling. Hence...

  10. Effect of Illumination Angle on the Performance of Dusted Thermal Control Surfaces in a Simulated Lunar Environment

    Science.gov (United States)

    Gaier, James R.

    2009-01-01

    JSC-1A lunar simulant has been applied to AZ93 and AgFEP thermal control surfaces on aluminum substrates in a simulated lunar environment. The temperature of these surfaces was monitored as they were heated with a solar simulator using varying angles of incidence and cooled in a 30 K coldbox. Thermal modeling was used to determine the solar absorptivity (a) and infrared emissivity (e) of the thermal control surfaces in both their clean and dusted states. It was found that even a sub-monolayer of dust can significantly raise the a of either type of surface. A full monolayer can increase the a/e ratio by a factor of 3 to 4 over a clean surface. Little angular dependence of the a of pristine thermal control surfaces for both AZ93 and AgFEP was observed, at least until 30 from the surface. The dusted surfaces showed the most angular dependence of a when the incidence angle was in the range of 25 to 35 . Samples with a full monolayer, like those with no dust, showed little angular dependence in a. The e of the dusted thermal control surfaces was within the spread of clean surfaces, with the exception of high dust coverage, where a small increase was observed at shallow angles.

  11. Development of non-thermal atmospheric pressure plasma system for surface modification of polymeric materials

    Science.gov (United States)

    Kasih, T. P.

    2017-04-01

    Non-thermal plasma has become one of the new technologies which are highly developed now days. This happens because the cold plasma using the principle of generated reactive gases that have the ability to modify the surface properties of a material or product without changing the original characteristics of the material. The purpose of this study is to develop a cold plasma system that operates at atmospheric pressure and investigates the effect of cold plasma treatment to change the surface characteristics of the polymer material polyethylene (PE) at various time conditions. We are successfully developing a non-thermal plasma system that can operate at atmospheric pressure and can be run with Helium or Argon gas. The characteristics of plasma will be discussed from the view of its electrical property, plasma discharge regime andoperation temperature. Experiment results on plasma treatment on PE material shows the changes of surface properties of originally hydrophobic material PE becomes hydrophilic by only few seconds of plasma treatment and level of hydrophilicity become greater with increasing duration of plasma treatment. Confirmation of this is shown by the measurement of contact angle of droplets of water on the surface of PE are getting smaller.

  12. Non-thermal desorption from interstellar dust grains via exothermic surface reactions

    CERN Document Server

    Garrod, R T; Herbst, E

    2007-01-01

    Aims: The gas-phase abundance of methanol in dark quiescent cores in the interstellar medium cannot be explained by gas-phase chemistry. In fact, the only possible synthesis of this species appears to be production on the surfaces of dust grains followed by desorption into the gas. Yet, evaporation is inefficient for heavy molecules such as methanol at the typical temperature of 10 K. It is necessary then to consider non-thermal mechanisms for desorption. But, if such mechanisms are considered for the production of methanol, they must be considered for all surface species. Methods: Our gas-grain network of reactions has been altered by the inclusion of a non-thermal desorption mechanism in which the exothermicity of surface addition reactions is utilized to break the bond between the product species and the surface. Our estimated rate for this process derives from a simple version of classical unimolecular rate theory with a variable parameter only loosely contrained by theoretical work. Results: Our results ...

  13. Optical and thermal properties in ultrafast laser surface nanostructuring on biodegradable polymer

    Science.gov (United States)

    Yada, Shuhei; Terakawa, Mitsuhiro

    2015-03-01

    We investigate the effect of optical and thermal properties in laser-induced periodic surface structures (LIPSS) formation on a poly-L-lactic acid (PLLA), a biodegradable polymer. Surface properties of biomaterials are known to be one of the key factors in tissue engineering. Methods to process biomaterial surfaces have been studied widely to enhance cell adhesive and anisotropic properties. LIPSS formation has advantages in a dry processing which is able to process complex-shaped surfaces without using a toxic chemical component. LIPSS, however, was difficult to be formed on PLLA due to its thermal and optical properties compared to other polymers. To obtain new perspectives in effect of these properties above, LIPSS formation dependences on wavelength, pulse duration and repetition rate have been studied. At 800 nm of incident wavelength, high-spatial frequency LIPSS (HSFL) was formed after applying 10000 femtosecond pulses at 1.0 J/cm2 in laser fluence. At 400 nm of the wavelength, HSFL was formed at fluences higher than 0.20 J/cm2 with more than 3000 pulses. Since LIPSS was less formed with lower repetition rate, certain heat accumulation may be required for LIPSS formation. With the pulse duration of 2.0 ps, higher laser fluence as well as number of pulses compared to the case of 120 fs was necessary. This indicates that multiphoton absorption process is essential for LIPSS formation. Study on biodegradation modification was also performed.

  14. Mechanical, Thermal Degradation, and Flammability Studies on Surface Modified Sisal Fiber Reinforced Recycled Polypropylene Composites

    Directory of Open Access Journals (Sweden)

    Arun Kumar Gupta

    2012-01-01

    Full Text Available The effect of surface treated sisal fiber on the mechanical, thermal, flammability, and morphological properties of sisal fiber (SF reinforced recycled polypropylene (RPP composites was investigated. The surface of sisal fiber was modified with different chemical reagent such as silane, glycidyl methacrylate (GMA, and O-hydroxybenzene diazonium chloride (OBDC to improve the compatibility with the matrix polymer. The experimental results revealed an improvement in the tensile strength to 11%, 20%, and 31.36% and impact strength to 78.72%, 77%, and 81% for silane, GMA, and OBDC treated sisal fiber reinforced recycled Polypropylene (RPP/SF composites, respectively, as compared to RPP. The thermogravimetric analysis (TGA, differential scanning calorimeter (DSC, and heat deflection temperature (HDT results revealed improved thermal stability as compared with RPP. The flammability behaviour of silane, GMA, and OBDC treated SF/RPP composites was studied by the horizontal burning rate by UL-94. The morphological analysis through scanning electron micrograph (SEM supports improves surface interaction between fiber surface and polymer matrix.

  15. Thermal inertia as an indicator of rockiness variegation on near-Earth asteroid surfaces

    Science.gov (United States)

    Ali-Lagoa, Victor; Delbo, Marco; Hanus, Josef

    2016-10-01

    Determining key physical properties of asteroids such as sizes and albedos or reflectance spectra is crucial to understand their origins and the processes that they have undergone during their evolution. In particular, one of the aims of NEOShield-2 project, funded by the European Union's Horizon 2020 Research and Innovation programme, is to physically characterize small near Earth asteroids (NEA) in an effort to determine effective mitigation strategies in case of impact with our planet [Harris et al. 2013 2013AcAau,90,80H].We performed thermophysical modelling of NEAs, such as (1685) Toro, and potentially hazardous asteroids (PHAs), such as (33342) 1998 WT24. In addition to size, thermophysical models (TPM) of asteroids can constrain the surface thermal inertia, which is related to the material composition and physical nature, namely its "rockiness" or typical size of the particles on its surface. These have observable effects on the surface temperature distribution as a function of time and thus on the thermal infrared fluxes we observe, to which we can fit our model.In the case of WT24, its thermal inertia has been previously constrained to be in the range 100-300 SI units [Harris et al. 2007, Icarus 188, 414H]. But this was based on a spherical shape model approximation since no shape model was available by the time. Such a low thermal inertia value seems in disagreement with a relatively high metal content of the enstatite chondrites, the meteorite type to which WT24, classified as an E-type [Lazzarin et al. 2004 A&A 425L, 25L], has been spectrally associated. Using a three-dimensional model and spin vector based on radar observations [Busch et al. 2008 Icarus 197, 375B], our TPM produces a higher best-fitting value of the thermal inertia. We also find the intriguing possibility that the hemisphere of WT24 dominated by concave terrains, possibly be the result of an impact crater, has a higher thermal inertia. This would be similar to the case of our Moon

  16. Polyphenol oxidase activity as a potential intrinsic index of adequate thermal pasteurization of apple cider.

    Science.gov (United States)

    Chen, L; Ingham, B H; Ingham, S C

    2004-05-01

    In response to increasing concerns about microbial safety of apple cider, the U.S. Food and Drug Administration has mandated treatment of cider sufficient for a 5-log reduction of the target pathogen. Pasteurization has been suggested as the treatment most likely to achieve a 5-log reduction, with Escherichia coli O157:H7 as the target pathogen. Regulators and processors need a reliable method for verifying pasteurization, and apple cider polyphenol oxidase (PPO) activity was studied as a potential intrinsic index for thermal pasteurization. The effect of pasteurization conditions and apple cider properties on PPO activity and survival of three pathogens (E. coli O157:H7, Salmonella, and Listeria monocytogenes) was studied using a Box-Behnken response surface design. Factors considered in the design were pasteurization conditions, i.e., hold temperature (60, 68, and 76 degrees C), preheat time (10, 20, 30 s), and hold time (0, 15, 30 s), pH, and sugar content ((o)Brix) of apple cider. Response surface contour plots were constructed to illustrate the effect of these factors on PPO activity and pathogen survival. Reduction in PPO activity of at least 50% was equivalent to a 5-log reduction in E. coli O157:H7 or L. monocytogenes for cider at pH 3.7 and 12.5 (o)Brix. Further studies, however, are needed to verify the relationship between PPO activity and pathogen reduction in cider with various pH and (o)Brix values.

  17. Thermally aware, durable nanoengineered surfaces with high speed liquid impalement resistance

    Science.gov (United States)

    Tiwari, Manish; Peng, Chaoyi; Chen, Zhuyang

    2016-11-01

    Highly hydrophobic nanoengineered surfaces delaying freezing down to -20 degrees Centigrade for a day, sustaining dropwise steam condensation under high rate steam shear for several days, sustaining mechanical abrasion and high strains have attracted strong interest recently. Particularly, anti-icing and dropwise condensation promotion require thermally conductive surfaces with careful nucleation control - of ice germs or droplets, respectively - using precise surface nanotexture. Scalability of surface manufacture is an additional challenge. In the current presentation, we will demonstrate a pathway to address these needs. Anodisation of metallic substrate is first used to obtain nanotextured surfaces with a precision of approx. 200 nm. Next, rationally formulated nanocomposites comprising solution processed fluorinated copolymers and nanoparticle dispersions were spray coated on the anodized metals. The resulting nanocomposite coatings were superhydrophobic with approx. 20 nm precision in surface texture. The surface durability is assessed using tape peel, sand abrasion, and droplet and water jet impact tests up to 30 m/s. High speed jet splashing is recorded at speeds >10 m/s to demonstrate the influence of jet diameter on splashing characteristics. This work was partly supported by EPSRC Grant EP/N006577/1.

  18. Weathering performance of surface of thermally modified wood finished with nanoparticles-modified waterborne polyacrylate coatings

    Science.gov (United States)

    Miklečić, Josip; Turkulin, Hrvoje; Jirouš-Rajković, Vlatka

    2017-06-01

    In this research the samples of thermally modified (TMT) beech wood samples, finished with waterborne polyacrylate clear coatings modified with nano-sized ZnO and TiO2-rutil were naturally and artificially exposed to weathering conditions. To extend the lifetime of wood and maintain its natural look, the research and development of clear coatings with minimal use of harmful chemicals has become very important. Therefore nano-sized inorganic UV absorbers are increasingly used to enhance the durability of the coating and wood substrate, still retaining the transparency of the coating. During exposure the visual inspection was performed, further the changes of colour, gloss and adhesion were recorded. Interaction of the film with the thermally modified substrate surface were studied. Results showed that the addition of TiO2-rutil and ZnO nanoparticles to the waterborne polyacrylate coating improved the colour stability of thermally modified beech-wood. However, nano-sized ZnO increased the cracking and peeling, and caused the loss in adhesion strength of the film on thermally modified beech wood.

  19. Photo-thermal modulation of surface plasmon polariton propagation at telecommunication wavelengths.

    Science.gov (United States)

    Kaya, S; Weeber, J-C; Zacharatos, F; Hassan, K; Bernardin, T; Cluzel, B; Fatome, J; Finot, C

    2013-09-23

    We report on photo-thermal modulation of thin film surface plasmon polaritons (SPP) excited at telecom wavelengths and traveling at a gold/air interface. By operating a modulated continuous-wave or a Q-switched nanosecond pump laser, we investigate the photo-thermally induced modulation of SPP propagation mediated by the temperature-dependent ohmic losses in the gold film. We use a fiber-to-fiber characterization set-up to measure accurately the modulation depth of the SPP signal under photo-thermal excitation. On the basis of these measurements, we extract the thermo-plasmonic coefficient of the SPP mode defined as the temperature derivative of the SPP damping constant. Next, we introduce a figure of merit which is relevant to characterize the impact of temperature onto the properties of bounded or weakly leaky SPP modes supported by a given metal at a given wavelength. By combining our measurements with tabulated values of the temperature-dependent imaginary part of gold dielectric function, we compute the thermo-optical coefficients (TOC) of gold at telecom wavelengths. Finally, we investigate a pulsed photo-thermal excitation of the SPP in the nanosecond regime. The experimental SPP depth of modulation obtained in this situation are found to be in fair agreement with the modulation depths computed by using our values of gold TOC.

  20. Ground Plane and Near-Surface Thermal Analysis for NASA's Constellation Program

    Science.gov (United States)

    Gasbarre, Joseph F.; Amundsen, Ruth M.; Scola, Salvatore; Leahy, Frank F.; Sharp, John R.

    2008-01-01

    Most spacecraft thermal analysis tools assume that the spacecraft is in orbit around a planet and are designed to calculate solar and planetary fluxes, as well as radiation to space. On NASA Constellation projects, thermal analysts are also building models of vehicles in their pre-launch condition on the surface of a planet. This process entails making some modifications in the building and execution of a thermal model such that the radiation from the planet, both reflected albedo and infrared, is calculated correctly. Also important in the calculation of pre-launch vehicle temperatures are the natural environments at the vehicle site, including air and ground temperatures, sky radiative background temperature, solar flux, and optical properties of the ground around the vehicle. A group of Constellation projects have collaborated on developing a cohesive, integrated set of natural environments that accurately capture worst-case thermal scenarios for the pre-launch and launch phases of these vehicles. The paper will discuss the standardization of methods for local planet modeling across Constellation projects, as well as the collection and consolidation of natural environments for launch sites. Methods for Earth as well as lunar sites will be discussed.

  1. Surface Thermal Insulation and Pipe Cooling of Spillways during Concrete Construction Period

    Directory of Open Access Journals (Sweden)

    Wang Zhenhong

    2014-01-01

    Full Text Available Given that spillways adopt a hydraulic thin concrete plate structure, this structure is difficult to protect from cracks. The mechanism of the cracks in spillways shows that temperature stress is the major reason for cracks. Therefore, an effective way of preventing cracks is a timely and reasonable temperature-control program. Studies show that one effective prevention method is surface thermal insulation combined with internal pipe cooling. The major factors influencing temperature control effects are the time of performing thermal insulation and the ways of internal pipe cooling. To solve this problem, a spillway is taken as an example and a three-dimensional finite element program and pipe cooling calculation method are adopted to conduct simulation calculation and analysis on the temperature fields and stress fields of concretes subject to different temperature-control programs. The temperature-control effects are then compared. Optimization results show that timely and reasonable surface thermal insulation and water-flowing mode can ensure good temperature-control and anticrack effects. The method has reference value for similar projects.

  2. Thermally induced growth of ZnO nanocrystals on mixed metal oxide surfaces.

    Science.gov (United States)

    Inayat, Alexandra; Makky, Ayman; Giraldo, Jose; Kuhnt, Andreas; Busse, Corinna; Schwieger, Wilhelm

    2014-06-23

    An in situ method for the growth of ZnO nanocrystals on Zn/Al mixed metal oxide (MMO) surfaces is presented. The key to this method is the thermal treatment of Zn/Al layered double hydroxides (Zn/Al LDHs) in the presence of nitrate anions, which results in partial demixing of the LDH/MMO structure and the subsequent crystallization of ZnO crystals on the surface of the forming MMO layers. In a first experimental series, thermal treatment of Zn/Al LDHs with different fractions of nitrate and carbonate in the interlayer space was examined by thermogravimetry coupled with mass spectrometry (TG-MS) and in situ XRD. In a second experimental series, Zn/Al LDHs with only carbonate in the interlayer space were thermally treated in the presence of different amounts of an external nitrate source (NH4NO3). All obtained Zn/Al MMO samples were analysed by electron microscopy, nitrogen physisorption and powder X-ray diffraction. The gas phase formed during nitrate decomposition turned out to be responsible for the formation of crystalline ZnO nanoparticles. Accordingly, both interlayer nitrate and the presence of ammonium nitrate led to the formation of supported ZnO nanocrystals with mean diameters between 100 and 400 nm, and both methods offer the possibility to tailor the amount and size of the ZnO crystals by means of the amount of nitrate.

  3. Comparison of MESSENGER Optical Images with Thermal and Radar Data for the Surface of MERCURY

    Science.gov (United States)

    Blewett, D. T.; Coman, E. I.; Chabot, N. L.; Izenberg, N. R.; Harmon, J. K.; Neish, C.

    2010-12-01

    Images collected by the MESSENGER spacecraft during its three Mercury flybys cover nearly the entire surface of the planet that was not imaged by Mariner 10. The MESSENGER data now allow us to observe features at optical wavelengths that were previously known only through remote sensing in other portions of the electromagnetic spectrum. For example, the Mariner 10 infrared (IR) radiometer made measurements along a track on the night side of Mercury during the spacecraft's first encounter in 1974. Analysis of the IR radiometer data identified several thermal anomalies that we have correlated to craters with extensive rays or ejecta deposits, including Xiao Zhao and Eminescu. The thermal properties are consistent with a greater exposure of bare rock (exposed in steep walls or as boulders and cobbles) in and around these craters compared with the lower-thermal-inertia, finer-grained regolith of the surrounding older surface. The portion of Mercury not viewed by Mariner 10 has also been imaged by Earth-based radar. The radar backscatter gives information on the wavelength-scale surface roughness. Arecibo S-band (12.6-cm wavelength) radar observations have produced images of Eminescu and also revealed two spectacular rayed craters (Debussy and Hokusai) that have since been imaged by MESSENGER. We are examining radial profiles for these craters, extracted from both the radar images and MESSENGER narrow-angle camera mosaics, that extend from the crater center outwards to a distance of several crater diameters. Comparison of optical and radar profiles for the craters, as well as similar profiles for lunar craters, can provide insight into ejecta deposition, the effect of surface gravity on the cratering process, and space weathering.

  4. Atmospheric Pressure non-thermal plasmas for surface treatment of polymer films

    Science.gov (United States)

    Huang, Hsiao-Feng; Wen, Chun-Hsiang; Wei, Hsiao-Kuan; Kou, Chwung-Shan

    2006-10-01

    Interest has grown over the past few years in applying atmospheric pressure non-thermal plasmas to surface treatment. In this work, we used an asymmetric glow dielectric-barrier discharge (GDBD), at atmospheric pressure in nitrogen, to improve the surface hydrophilicity of three kinds of polymer films, biaxially oriented polypropylene (BOPP), polyimide (PI), and triacetyl cellulose (TAC). This set-up consists of two asymmetric electrodes covered by dielectrics. And to prevent the filamentary discharge occur, the frequency, gas flow rate and uniformity of gas flow distribution should be carefully controlled. The discharge performance is monitored through an oscilloscope, which is connected to a high voltage probe and a current monitor. The physical and chemical properties of polymer surfaces before and after GDBD treatment were analyzed via water contact angle (CA) measurements, atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS) techniques.

  5. Vibration analysis of viscoelastic inhomogeneous nanobeams incorporating surface and thermal effects

    Science.gov (United States)

    Ebrahimi, Farzad; Barati, Mohammad Reza

    2017-01-01

    This article deals with the free vibration investigation of nonlocal strain gradient-based viscoelastic functionally graded (FG) nanobeams on viscoelastic medium considering surface stress effects. Nonlocal strain gradient theory possesses a nonlocal stress field parameter and a length scale parameter for more accurate prediction of mechanical behavior of nanostructures. Surface energy effect is incorporate to the nonlocal strain gradient theory employing Gurtin-Murdoch elasticity theory. Thermo-elastic material properties of nanobeam are graded in thickness direction using power-law distribution. Hamilton's principal is utilized to obtain the governing equations of FG nanobeam embedded in viscoelastic medium. The effects of surface stress, length scale parameter, nonlocal parameter, viscoelastic medium, internal damping constant, thermal loading, power-law index and boundary conditions on vibration frequencies of viscoelastic FGM nanobeams are discussed in detail.

  6. Surface studies of the thermal decomposition of triethylgallium on GaAs (100)

    Science.gov (United States)

    Murrell, A. J.; Wee, A. T. S.; Fairbrother, D. H.; Singh, N. K.; Foord, J. S.; Davies, G. J.; Andrews, D. A.

    1990-10-01

    The adsorption and surface decomposition of triethylgallium (TEG) on GaAs (100) has been studied using XPS and thermal desorption techniques. TEG is found to adsorb in a molecular form on the Ga rich (4×1) surface below 150 K. As the surface temperature is raised, this molecular state dissociates to form Ga and adsorbed ethyl species. The overall cracking reaction occurs in competition with the desorption of TEG and diethylgallium (DEG). Under the conditions of our experiments the adsorbed ethyl species formed above are found to dissociate above 600 K to form mainly gas phase ethene and hydrogen with traces of ethane, resulting in the formation of a pure Ga layer within the sensitivity limits imposed by XPS.

  7. Microporous activated carbons prepared from palm shell by thermal activation and their application to sulfur dioxide adsorption.

    Science.gov (United States)

    Guo, Jia; Lua, Aik Chong

    2002-07-15

    Textural characterization of activated carbons prepared from palm shell by thermal activation with carbon dioxide (CO(2)) gas is reported in this paper. Palm shell (endocarp) is an abundant agricultural solid waste from palm-oil processing mills in many tropical countries such as Malaysia, Indonesia, and Thailand. The effects of activation temperature on the textural properties of the palm-shell activated carbons, namely specific surface area (BET method), porosity, and microporosity, were investigated. The activated carbons prepared from palm shell possessed well-developed porosity, predominantly microporosity, leading to potential applications in gas-phase adsorption for air pollution control. Static and dynamic adsorption tests for sulfur dioxide (SO(2)), a common gaseous pollutant, were carried out in a thermogravimetric analyzer and a packed column configuration respectively. The effects of adsorption temperature, adsorbate inlet concentration, and adsorbate superficial velocity on the adsorptive performance of the prepared activated carbons were studied. The palm-shell activated carbon was found to have substantial capability for the adsorption of SO(2), comparable to those of some commercial products and an adsorbent derived from another biomass.

  8. Nuclear Thermal Rocket Element Environmental Simulator (NTREES) Upgrade Activities

    Science.gov (United States)

    Emrich, William J., Jr.

    2014-01-01

    Over the past year the Nuclear Thermal Rocket Element Environmental Simulator (NTREES) has been undergoing a significant upgrade beyond its initial configuration. The NTREES facility is designed to perform realistic non-nuclear testing of nuclear thermal rocket (NTR) fuel elements and fuel materials. Although the NTREES facility cannot mimic the neutron and gamma environment of an operating NTR, it can simulate the thermal hydraulic environment within an NTR fuel element to provide critical information on material performance and compatibility. The first phase of the upgrade activities which was completed in 2012 in part consisted of an extensive modification to the hydrogen system to permit computer controlled operations outside the building through the use of pneumatically operated variable position valves. This setup also allows the hydrogen flow rate to be increased to over 200 g/sec and reduced the operation complexity of the system. The second stage of modifications to NTREES which has just been completed expands the capabilities of the facility significantly. In particular, the previous 50 kW induction power supply has been replaced with a 1.2 MW unit which should allow more prototypical fuel element temperatures to be reached. The water cooling system was also upgraded to so as to be capable of removing 100% of the heat generated during. This new setup required that the NTREES vessel be raised onto a platform along with most of its associated gas and vent lines. In this arrangement, the induction heater and water systems are now located underneath the platform. In this new configuration, the 1.2 MW NTREES induction heater will be capable of testing fuel elements and fuel materials in flowing hydrogen at pressures up to 1000 psi at temperatures up to and beyond 3000 K and at near-prototypic reactor channel power densities. NTREES is also capable of testing potential fuel elements with a variety of propellants, including hydrogen with additives to inhibit

  9. Ground surface temperature reconstructions: Using in situ estimates for thermal conductivity acquired with a fiber-optic distributed thermal perturbation sensor

    Energy Technology Data Exchange (ETDEWEB)

    Freifeld, B.M.; Finsterle, S.; Onstott, T.C.; Toole, P.; Pratt, L.M.

    2008-10-10

    We have developed a borehole methodology to estimate formation thermal conductivity in situ with a spatial resolution of one meter. In parallel with a fiber-optic distributed temperature sensor (DTS), a resistance heater is deployed to create a controlled thermal perturbation. The transient thermal data is inverted to estimate the formation's thermal conductivity. We refer to this instrumentation as a Distributed Thermal Perturbation Sensor (DTPS), given the distributed nature of the DTS measurement technology. The DTPS was deployed in permafrost at the High Lake Project Site (67 degrees 22 minutes N, 110 degrees 50 minutes W), Nunavut, Canada. Based on DTPS data, a thermal conductivity profile was estimated along the length of a wellbore. Using the thermal conductivity profile, the baseline geothermal profile was then inverted to estimate a ground surface temperature history (GSTH) for the High Lake region. The GSTH exhibits a 100-year long warming trend, with a present-day ground surface temperature increase of 3.0 {+-} 0.8 C over the long-term average.

  10. Characterization of an Active Thermal Erosion Site, Caribou Creek, Alaska

    Science.gov (United States)

    Busey, R.; Bolton, W. R.; Cherry, J. E.; Hinzman, L. D.

    2013-12-01

    The goal of this project is to estimate volume loss of soil over time from this site, provide parameterizations on erodibility of ice rich permafrost and serve as a baseline for future landscape evolution simulations. Located in the zone of discontinuous permafrost, the interior region of Alaska (USA) is home to a large quantity of warm, unstable permafrost that is both high in ice content and has soil temperatures near the freezing point. Much of this permafrost maintains a frozen state despite the general warming air temperature trend in the region due to the presence of a thick insulating organic mat and a dense root network in the upper sub-surface of the soil column. At a rapidly evolving thermo-erosion site, located within the Caribou-Poker Creeks Research Watershed (part of the Bonanza Creek LTER) near Chatanika, Alaska (N65.140, W147.570), the protective organic layer and associated plants were disturbed by an adjacent traditional use trail and the shifting of a groundwater spring. These triggers have led to rapid geomorphological change on the landscape as the soil thaws and sediment is transported into the creek at the valley bottom. Since 2006 (approximately the time of initiation), the thermal erosion has grown to 170 meters length, 3 meters max depth, and 15 meters maximum width. This research combines several data sets: DGPS survey, imagery from an extremely low altitude pole-based remote sensing (3 to 5 meters above ground level), and imagery from an Unmanned Aerial System (UAS) at about 60m altitude.

  11. Thermal cycling tests of actively cooled beryllium copper joints

    Energy Technology Data Exchange (ETDEWEB)

    Roedig, M.; Duwe, R.; Linke, J.; Schuster, A.; Wiechers, B. [Forschungszentrum Juelich GmbH (Germany)

    1998-01-01

    Screening tests (steady state heating) and thermal fatigue tests with several kinds of beryllium-copper joints have been performed in an electron beam facility. Joining techniques under investigation were brazing with silver containing and silver-free braze materials, hot isostatic pressing (HIP) and diffusion bonding (hot pressing). Best thermal fatigue performance was found for the brazed samples. (author)

  12. Environmental and Economic Analysis of Thermal Active Building System

    Directory of Open Access Journals (Sweden)

    Paulo Fabiano Reis Lessa

    2016-05-01

    Full Text Available This paper is regarding one promising technological solution – which is so called Thermal Active Building Systems (TABS –for one of the most critical problems both in environmental and economic aspects, which is the raising energy consumption. Buildings are the principal application target of the solution once that population spends most part of their time inside them. Therefore, more energy is required to supply an increasingly demand in lighting, air conditioning, heating, electronic devices and so on. In this context, TABS emerge like a possible solution. To ensure the system efficiency or, in other words, prove its viability, it will be applied an environmental management tool (SWOT Analysis weighting all the pros and comparing with its drawbacks, based on previous experiences in implantation of such system, available in literature. A basic theoretical background, which is extremely important to a better comprehension of the system, covering both engineering and environmental management areas, is presented on this paper. Results shown that TABS are efficient mechanisms in the reduction of power consumption, committed with sustainable development, and which worth the investments in a Life Cycle Cost evaluation

  13. [Quantitative estimation of CaO content in surface rocks using hyperspectral thermal infrared emissivity].

    Science.gov (United States)

    Zhang, Li-Fu; Zhang, Xue-Wen; Huang, Zhao-Qiang; Yang, Hang; Zhang, Fei-Zhou

    2011-11-01

    The objective of the present paper is to study the quantitative relationship between the CaO content and the thermal infrared emissivity spectra. The surface spectral emissivity of 23 solid rocks samples were measured in the field and the first derivative of the spectral emissivity was also calculated. Multiple linear regression (MLR), principal component analysis (PCR) and partial least squares regression (PLSR) were modeled and the regression results were compared. The results show that there is a good relationship between CaO content and thermal emissivity spectra features; emissivities become lower when CaO content increases in the 10.3-13 mm region; the first derivative spectra have a better predictive ability compared to the original emissivity spectra.

  14. Land surface thermal characterization of Asian-pacific region with Japanese geostationary satellite

    Science.gov (United States)

    Oyoshi, K.; Tamura, M.

    2010-12-01

    Land Surface Temperature (LST) is a significant indicator of energy balance at the Earth's surface. It is required for a wide variety of climate, hydrological, ecological, and biogeochemical studies. Although LST is highly variable both temporally and spatially, it is impossible for polar-orbiting satellite to detect hourly changes in LST, because the satellite is able to only collect data of the same area at most twice a day. On the other hand, geostationary satellite is able to collect hourly data and has a possibility to monitor hourly changes in LST, therefore hourly measurements of geostationary satellite enables us to characterize detailed thermal conditions of the Earth's surface and improve our understanding of the surface energy balance. Multi-functional Transport Satellite (MTSAT) is a Japanese geostationary satellite launched in 2005 and covers Asia-Pacific region. MTSAT provides hourly data with 5 bands including two thermal infrared (TIR) bands in the 10.5-12.5 micron region. In this research, we have developed a methodology to retrieve hourly LST from thermal infrared data of MTSAT. We applied Generalized Split-window (GSW) equation to estimate LST from TIR data. First, the brightness temperatures measured at sensor on MTSAT was simulated by radiative transfer code (MODTRAN), and the numerical coefficients of GSW equation were optimized based on the simulation results with non-linear minimization algorithm. The standard deviation of derived GSW equation was less than or equal to 1.09K in the case of viewing zenith angle lower than 40 degree and 1.73K in 60 degree. Then, spatial distributions of LST have been mapped optimized GSW equation with brightness temperatures of MTSAT IR1 and IR2 and emissivity map from MODIS product. Finally, these maps were validated with MODIS LST product (MOD11A1) over four Asian-pacific regions such as Bangkok, Tokyo, UlanBator and Jakarta , It is found that RMSE of these regions were 4.57K, 2.22K, 2.71K and 3.92K

  15. Thermal Inertia Determination of C-type Asteroid Ryugu from in-situ Surface Brightness Temperature Measurements

    Science.gov (United States)

    Hamm, Maximilian; Grott, Matthias; Knollenberg, Jörg; Kührt, Ekkehard; Pelivan, Ivanka

    2016-10-01

    The Japanese Hayabusa-2 mission is a sample-return mission currently on its way to the C-type asteroid Ryugu. Hayabusa-2 carries the small lander MASCOT (Mobile Asteroid Surface Scout), whose scientific payload includes the infrared radiometer MARA. The primary science goal of MARA is to determine Ryugu's surface brightness temperatures at the landing site for a full asteroid rotation, which will be measured using a long-pass filter, an 8 to 12 µm bandpass, as well as four narrow bandpasses centered at wavelengths between 5 and 15 µm. From these measurements, surface thermal inertia will be derived, but because MARA performs single pixel measurements, heterogeneity in the field of view cannot be resolved. Yet, the surface will likely exhibit different surface textures, and thermal inertia in the field of view could vary from 600 (small rocks) to 50 Jm-2s-0.5K-1 (fine regolith grains). Sub-pixel heterogeneity is a common problem when interpreting radiometer data, since the associated ambiguities cannot be resolved without additional information on surface texture. For MARA, this information will be provided by the MASCOT camera, and in the present paper we have investigated to what extent different thermal inertias can be retrieved from MARA data. To test the applied approach, we generated synthetic MARA data using a thermal model of Ryugu, assuming different thermal inertias for sections of the field of view. We find that sub-pixel heterogeneity systematically deforms the diurnal temperature curve so that it is not possible to fit the data using a single thermal inertia value. However, including the area fractions of the different surface sections enables us to reconstruct the different thermal inertias to within 10% assuming appropriate measurement noise. The presented approach will increase robustness of the Ryugu thermal inertia determination and results will serve as a ground truth for the global measurements performed by the thermal infrared mapper (TIR) on

  16. Global trends in lake surface temperatures observed using multi-sensor thermal infrared imagery

    Science.gov (United States)

    Schneider, Philipp; Hook, Simon J.; Radocinski, Robert G.; Corlett, Gary K.; Hulley, Glynn C.; Schladow, S. Geoffrey; Steissberg, Todd E.

    2010-05-01

    Recent research has shown that the temperature of lakes and other inland water bodies does not only act as a good indicator of climate variability but under certain conditions can even increase more rapidly than the regional air temperature. Further investigation of this phenomenon in particular and of the interaction between lake temperature and climate variability in general requires extensive observations of lake temperature on a global scale. Current in situ records are limited in their spatial and/or temporal coverage and are thus insufficient for this task. However, a nearly 30-year archive of satellite-derived thermal infrared imagery from multiple sensors is available at this point and can be used to fill this data gap. We describe research on utilizing the existing archive of spaceborne thermal infrared imagery to generate multi-decadal time series of lake surface temperature for 170 of the largest lakes worldwide. The data used for this purpose includes imagery from the Advanced Very High Resolution Radiometers (AVHRR), the series of (Advanced) Along-Track Scanning Radiometers ((A)ATSR), and the Moderate Resolution Imaging Spectroradiometer (MODIS). Used in combination, these data sets offer a gapless time series of daily to near-daily thermal infrared retrievals from 1981 through present. In this contribution we demonstrate using comprehensive in situ data at Lake Tahoe, California/Nevada, that lake water surface temperature can be estimated using these sensors with an accuracy of up to 0.2 K. We further show that accurate continuous time series of water surface temperature can be derived from the data and that these time series can be used to detect significant trends in the temporal thermal behavior of lakes and other inland water bodies worldwide. Complementing our recent case study for lakes in California and Nevada for which a rapid increase in mean nighttime summertime lake surface temperatures of 0.11 K per year on average was found, we present

  17. Experimental investigation of thermal conductivity coefficient and heat exchange between fluidized bed and inclined exchange surface

    Directory of Open Access Journals (Sweden)

    B. Stojanovic

    2009-06-01

    Full Text Available The paper presents experimental research of thermal conductivity coefficients of the siliceous sand bed fluidized by air and an experimental investigation of the particle size influence on the heat transfer coefficient between fluidized bed and inclined exchange surfaces. The measurements were performed for the specific fluidization velocity and sand particle diameters d p=0.3, 0.5, 0.9 mm. The industrial use of fluidized beds has been increasing rapidly in the past 20 years owing to their useful characteristics. One of the outstanding characteristics of a fluidized bed is that it tends to maintain a uniform temperature even with nonuniform heat release. On the basis of experimental research, the influence of the process's operational parameters on the obtained values of the bed's thermal conductivity has been analyzed. The results show direct dependence of thermal conductivity on the intensity of mixing, the degree of fluidization, and the size of particles. In the axial direction, the coefficients that have been treated have values a whole order higher than in the radial direction. Comparison of experimental research results with experimental results of other authors shows good agreement and the same tendency of thermal conductivity change. It is well known in the literature that the value of the heat transfer coefficient is the highest in the horizontal and the smallest in the vertical position of the heat exchange surface. Variation of heat transfer, depending on inclination angle is not examined in detail. The difference between the values of the relative heat transfer coefficient between vertical and horizontal heater position for all particle sizes reduces by approximately 15% with the increase of fluidization rate.

  18. Factorial Based Response Surface Modeling with Confidence Intervals for Optimizing Thermal Optical Transmission Analysis of Atmospheric Black Carbon

    Science.gov (United States)

    We demonstrate how thermal-optical transmission analysis (TOT) for refractory light-absorbing carbon in atmospheric particulate matter was optimized with empirical response surface modeling. TOT employs pyrolysis to distinguish the mass of black carbon (BC) from organic carbon (...

  19. Thermal activation of superheated lipid-coated perfluorocarbon drops.

    Science.gov (United States)

    Mountford, Paul A; Thomas, Alec N; Borden, Mark A

    2015-04-28

    This study explored the thermal conditions necessary for the vaporization of superheated perfluorocarbon nanodrops. Droplets C3F8 and C4F10 coated with a homologous series of saturated diacylphosphatidylcholines were formed by condensation of 4 μm diameter microbubbles. These drops were stable at room temperature and atmospheric pressure, but they vaporized back into microbubbles at higher temperatures. The vaporization transition was measured as a function of temperature by laser light extinction. We found that C3F8 and C4F10 drops experienced 90% vaporization at 40 and 75 °C, respectively, near the theoretical superheat limits (80-90% of the critical temperature). We therefore conclude that the metastabilty of these phase-change agents arises not from the droplet Laplace pressure altering the boiling point, as previously reported, but from the metastability of the pure superheated fluid to homogeneous nucleation. The rate of C4F10 drop vaporization was quantified at temperatures ranging from 55 to 75 °C, and an apparent activation energy barrier was calculated from an Arrhenius plot. Interestingly, the activation energy increased linearly with acyl chain length from C14 to C20, indicating that lipid interchain cohesion plays an important role in suppressing the vaporization rate. The vaporized drops (microbubbles) were found to be unstable to dissolution at high temperatures, particularly for C14 and C16. However, proper choice of the fluorocarbon and lipid species provided a nanoemulsion that could undergo at least ten reversible condensation/vaporization cycles. The vaporization properties presented in this study may facilitate the engineering of tunable phase-shift particles for diagnostic imaging, targeted drug delivery, tissue ablation, and other applications.

  20. [Correlative analysis of the diversity patterns of regional surface water, NDVI and thermal environment].

    Science.gov (United States)

    Duan, Jin-Long; Zhang, Xue-Lei

    2012-10-01

    Taking Zhengzhou City, the capital of Henan Province in Central China, as the study area, and by using the theories and methodologies of diversity, a discreteness evaluation on the regional surface water, normalized difference vegetation index (NDVI), and land surface temperature (LST) distribution was conducted in a 2 km x 2 km grid scale. Both the NDVI and the LST were divided into 4 levels, their spatial distribution diversity indices were calculated, and their connections were explored. The results showed that it was of operability and practical significance to use the theories and methodologies of diversity in the discreteness evaluation of the spatial distribution of regional thermal environment. There was a higher overlap of location between the distributions of surface water and the lowest temperature region, and the high vegetation coverage was often accompanied by low land surface temperature. In 1988-2009, the discreteness of the surface water distribution in the City had an obvious decreasing trend. The discreteness of the surface water distribution had a close correlation with the discreteness of the temperature region distribution, while the discreteness of the NDVI classification distribution had a more complicated correlation with the discreteness of the temperature region distribution. Therefore, more environmental factors were needed to be included for a better evaluation.

  1. Implications of Adhesion Studies for Dust Mitigation on Thermal Control Surfaces

    Science.gov (United States)

    Gaier, James R.; Berkebile, Stephen P.

    2012-01-01

    Experiments measuring the adhesion forces under ultrahigh vacuum conditions (10 (exp -10) torr) between a synthetic volcanic glass and commonly used space exploration materials have recently been described. The glass has a chemistry and surface structure typical of the lunar regolith. It was found that Van der Waals forces between the glass and common spacecraft materials was negligible. Charge transfer between the materials was induced by mechanically striking the spacecraft material pin against the glass plate. No measurable adhesion occurred when striking the highly conducting materials, however, on striking insulating dielectric materials the adhesion increased dramatically. This indicates that electrostatic forces dominate over Van der Waals forces under these conditions. The presence of small amounts of surface contaminants was found to lower adhesive forces by at least two orders of magnitude, and perhaps more. Both particle and space exploration material surfaces will be cleaned by the interaction with the solar wind and other energetic processes and stay clean because of the extremely high vacuum (10 (exp -12) torr) so the atomically clean adhesion values are probably the relevant ones for the lunar surface environment. These results are used to interpret the results of dust mitigation technology experiments utilizing textured surfaces, work function matching surfaces and brushing. They have also been used to reinterpret the results of the Apollo 14 Thermal Degradation Samples experiment.

  2. Thermally Sprayed Coatings as Effective Tool Surfaces in Sheet Metal Forming Applications

    Science.gov (United States)

    Franzen, V.; Witulski, J.; Brosius, A.; Trompeter, M.; Tekkaya, A. E.

    2011-06-01

    Two approaches to produce wear-resistant effective surfaces for deep drawing tools by thermal arc wire spraying of hard materials are presented. Arc wire spraying is a very economic coating technique due to a high deposition rate. The coated surface is very rough compared to that of conventional sheet metal forming tools. In the first approach, the coated surface is smoothed in a subsequent CNC-based incremental roller burnishing process. In this process, the surface asperities on the surface are flattened, and the roughness is significantly reduced. In the second approach, the hard material coatings are not sprayed directly on the tool but on a negative mould. Afterward, the rough "as-sprayed" side of the coating is backfilled with a polymer. The bonded hard metal shell is removed from the negative mould and acts as the surface of the hybrid sheet metal forming tool. Sheet metal forming experiments using tools based on these two approaches demonstrate that they are suitable to form high-strength steels. Owing to a conventional body of steel or cast iron, the first approach is suitable for large batch sizes. The application of the second approach lies within the range of small up to medium batch size productions.

  3. Thermal shock behaviour of blisters on W surface during combined steady-state/pulsed plasma loading

    Science.gov (United States)

    Jia, Y. Z.; Liu, W.; Xu, B.; Luo, G.-N.; Li, C.; Qu, S. L.; Morgan, T. W.; De Temmerman, G.

    2015-09-01

    The thermal shock behaviour of blister-covered W surfaces during combined steady-state/pulsed plasma loading was studied by scanning electron microscopy and electron backscatter diffraction. The W samples were first exposed to steady-state D plasma to induce blisters on the surface, and then the blistered surfaces were exposed to steady-state/pulsed plasma. Growth and cracking of blisters were observed after the exposure to the steady-state/pulsed plasma, while no obvious damage occurred on the surface area not covered with blisters. The results confirm that blisters induced by D plasma might represent weak spots on the W surface when exposed to transient heat load of ELMs. The cracks on blisters were different from the cracks due to the transient heat loads reported before, and they were assumed to be caused by stress and strain due to the gas expansion inside the blisters during the plasma pulses. Moreover, most of cracks were found to appear on the blisters formed on grains with surface orientation near [1 1 1].

  4. A thermal monitoring sheet with low influence from adjacent waterbolus for tissue surface thermometry during clinical hyperthermia.

    Science.gov (United States)

    Arunachalam, Kavitha; Maccarini, Paolo F; Stauffer, Paul R

    2008-10-01

    This paper presents a complete thermal analysis of a novel conformal surface thermometer design with directional sensitivity for real-time temperature monitoring during hyperthermia treatments of large superficial cancer. The thermal monitoring sheet (TMS) discussed in this paper consists of a 2-D array of fiberoptic sensors embedded between two layers of flexible, low-loss, and thermally conductive printed circuit board (PCB) film. Heat transfer across all interfaces from the tissue surface through multiple layers of insulating dielectrics surrounding the small buried temperature sensor and into an adjacent temperature-regulated water coupling bolus was studied using 3-D thermal simulation software. Theoretical analyses were carried out to identify the most effective differential TMS probe configuration possible with commercially available flexible PCB materials and to compare their thermal responses with omnidirectional probes commonly used in clinical hyperthermia. A TMS sensor design that employs 0.0508-mm Kapton MTB and 0.2032-mm Kapton HN flexible polyimide films is proposed for tissue surface thermometry with low influence from the adjacent waterbolus. Comparison of the thermal simulations with clinical probes indicates the new differential TMS probe design to outperform in terms of both transient response and steady-state accuracy in selectively reading the tissue surface temperature, while decreasing the overall thermal barrier of the probe between the coupling waterbolus and tissue surface.

  5. Tunable wideband-directive thermal emission from SiC surface using bundled graphene sheets

    Science.gov (United States)

    Inampudi, Sandeep; Mosallaei, Hossein

    2017-09-01

    Coherent thermal radiation emitters based on diffraction gratings inscribed on surface of a polar material, such as silicon carbide, always possess high angular dispersion resulting in wideband-dispersive or monochromatic-directive emission. In this paper, we identify roots of the high angular dispersion as the rapid surface phonon polariton (SPhP) resonance of the material surface and the misalignment of the dispersion curve of the diffraction orders of the grating with respect to light line. We minimize the rapid variation of SPhP resonance by compensating the material dispersion using bundled graphene sheets and mitigate the misalignment by a proper choice of the grating design. Utilizing a modified form of rigorous coupled wave analysis to simultaneously incorporate atomic-scale graphene sheets and bulk diffraction gratings, we accurately compute the emissivity profiles of the composite structure and demonstrate reduction in the angular dispersion of thermal emission from as high as 30∘ to as low as 4∘ in the SPhP dominant wavelength range of 11-12 μ m . In addition, we demonstrate that the graphene sheets via their tunable optical properties allow a fringe benefit of dynamical variation of the angular dispersion to a wide range.

  6. Influence of thermal and surface effects on vibration behavior of nonlocal rotating Timoshenko nanobeam

    Science.gov (United States)

    Ghadiri, Majid; Shafiei, Navvab; Akbarshahi, Amir

    2016-07-01

    This paper is proposed to study the free vibration of a rotating Timoshenko nanobeam based on the nonlocal theory considering thermal and surface elasticity effects. The governing equations and the related boundary conditions are derived using the Hamilton's principle. In order to solve the problem, generalized differential quadrature method is applied to discretize the governing differential equations corresponding to clamped-simply and clamped-free boundary conditions. In this article, the influences of some parameters such as nonlocal parameter, angular velocity, thickness of the nanobeam, and thermal and surface elasticity effects on the free vibration of the rotating nanobeam are investigated, and the results are compared for different boundary conditions. The results show that the surface effect and the nonlocal parameter and the temperature changes have significant roles, and they should not be ignored in the vibrational study of rotating nanobeams. Also, the angular velocity and the hub radius have more significant roles than temperature change effects on the nondimensional frequency. It is found that the nonlocal parameter behavior and the temperature change behavior on the frequency are different in the first mode for the rotating cantilever nanobeam.

  7. Thermal stability of the work function of NEA type surfaces. [Negative Electron Affinity

    Science.gov (United States)

    Edwards, D., Jr.; Peria, W. T.

    1978-01-01

    The work-function stability of both Si(100) and Ge(100) surfaces activated with adsorptions of cesium and oxygen has been determined. In general, it has been found that the highest temperature to which the optimized Ge surface could be heated without an increase in its work function (1.06 eV) was about 200 C, whereas the optimized Si surface could be heated to approximately 250 C without a significant increase in the optimized work function (0.93 eV). Details are also presented on various characteristics of cesium and oxygen adsorption-desorption on these surfaces.

  8. Tungsten Incorporation into Gallium Oxide: Crystal Structure, Surface and Interface Chemistry, Thermal Stability and Interdiffusion

    Energy Technology Data Exchange (ETDEWEB)

    Rubio, E. J.; Mates, T. E.; Manandhar, S.; Nandasiri, M.; Shutthanandan, V.; Ramana, C. V.

    2016-12-01

    Tungsten (W) incorporated gallium oxide (Ga2O3) (GWO) thin films were deposited by radio-frequency magnetron co-sputtering of W-metal and Ga2O3-ceramic targets. Films were produced by varying sputtering power applied to the W-target in order to achieve variable W-content (0-12 at%) into Ga2O3 while substrate temperature was kept constant at 500 °C. Chemical composition, chemical valence states, microstructure and crystal structure of as-deposited and annealed GWO films were evaluated as a function of W-content. The structural and chemical analyses indicate that the samples deposited without any W-incorporation are stoichiometric, nanocrystalline Ga2O3 films, which crystallize in β-phase monoclinic structure. While GWO films also crystallize in monoclinic β-Ga2O3 phase, W-incorporation induces surface amorphization as revealed by structural studies. The chemical valence state of Ga ions probed by X-ray photoelectron spectroscopic (XPS) analyses is characterized by the highest oxidation state i.e., Ga3+. No changes in Ga chemical state are noted for variable W-incorporation in the range of 0-12 at%. Rutherford backscattering spectrometry (RBS) analyses indicate the uniform distribution of W-content in the GWO films. However, XPS analyses indicate the formation of mixed valence states for W ions, which may be responsible for surface amorphization in GWO films. GWO films were stable up to 900 oC, at which point thermally induced secondary phase (W-oxide) formation was observed. A transition to mesoporous structure coupled with W interdiffusion occurs due to thermal annealing as derived from the chemical analyses at the GWO films’ surface as well as depth-profiling towards the GWO-Si interface. A model has been formulated to account for the mechanism of W-incorporation, thermal stability and interdiffusion via pore formation in GWO films.

  9. Active layer thermal monitoring at Fildes Peninsula, King George Island, Maritime Antarctica

    Directory of Open Access Journals (Sweden)

    R. F. M. Michel

    2014-07-01

    Full Text Available International attention to the climate change phenomena has grown in the last decade; the active layer and permafrost are of great importance in understanding processes and future trends due to their role in energy flux regulation. The objective of the this paper is to present active layer temperature data for one CALM-S site located at Fildes Peninsula, King George Island, Maritime Antarctica over an fifth seven month period (2008–2012. The monitoring site was installed during the summer of 2008 and consists of thermistors (accuracy of ± 0.2 °C, arranged vertically with probes at different depths, recording data at hourly intervals in a~high capacity data logger. A series of statistical analysis were performed to describe the soil temperature time series, including a linear fit in order to identify global trend and a series of autoregressive integrated moving average (ARIMA models were tested in order to define the best fit for the data. The controls of weather on the thermal regime of the active layer have been identified, providing insights about the influence of climate chance over the permafrost. The active layer thermal regime in the studied period was typical of periglacial environment, with extreme variation at the surface during summer resulting in frequent freeze and thaw cycles. The active layer thickness (ALT over the studied period showed variability related to different annual weather conditions, reaching a maximum of 117.5 cm in 2009. The ARIMA model was considered appropriate to treat the dataset, enabling more conclusive analysis and predictions when longer data sets are available. Despite the variability when comparing temperature readings and active layer thickness over the studied period, no warming trend was detected.

  10. Identification of a basaltic component on the Martian surface from Thermal Emission Spectrometer data

    Science.gov (United States)

    Christensen, P.R.; Bandfield, J.L.; Smith, M.D.; Hamilton, V.E.; Clark, R.N.

    2000-01-01

    The Mars Global Surveyor Thermal Emission Spectrometer (TES) instrument collected 4.8 ?? 106 spectra of Mars during the initial aerobraking and science-phasing periods of the mission (September 14, 1997, through April 29, 1998). Two previously developed atmosphere-removal models were applied to data from Cimmeria Terra (25?? S, 213?? W). The surface spectra derived for these two models agree well, indicating that the surface and atmosphere emission can be separated and that the exact atmosphere-removal model used has little effect on the derived surface composition. The Cimmeria spectra do not match terrestrial high-silica igneous rocks (granite and rhyolite), ultramafic igneous rocks, limestone, or quartz- and clay-rich sandstone and siltstone. A particulate (sand-sized) sample of terrestrial flood basalt does provide an excellent match in both spectral shape and band depth to the Cimmeria spectrum over the entire TES spectral range. No unusual particle size effects are required to account for the observed spectral shape and depth. The implied grain size is consistent with the thermal inertia and albedo of this region, which indicate a sand-sized surface with little dust. The identification of basalt is consistent with previous indications of pyroxene and basalt-like compositions from visible/ near-infrared and thermal-infrared spectral measurements. A linear spectral deconvolution model was applied to both surface-only Cimmeria spectra using a library of 60 minerals to determine the composition and abundance of the component minerals. Plagioclase feldspar (45%; 53%) and clinopyroxene (26%; 19%) were positively identified above an estimated detection threshold of 10-15% for these minerals. The TES observations provide the first identification of feldspars on Mars. The best fit to the Mars data includes only clinopyroxene compositions; no orthopyroxene compositions are required to match the Cimmeria spectra. Olivine (12%; 12%) and sheet silicate (15%; 11%) were

  11. Analysis of Viking infrared thermal mapping data of Mars. The effects of non-ideal surfaces on the derived thermal properties of Mars

    Science.gov (United States)

    Muhleman, D. O.; Jakosky, B. M.

    1979-01-01

    The thermal interia of the surface of Mars varies spatially by a factor of eight. This is attributable to changes in the average particle size of the fine material, the surface elevation, the atmospheric opacity due to dust, and the fraction of the surface covered by rocks and fine material. The effects of these non-ideal properties on the surface temperatures and derived thermal inertias are modeled, along with the the effects of slopes, CO2 condensed onto the surface, and layering of fine material upon solid rock. The non-ideal models are capable of producing thermal behavior similar to that observed by the Viking Infrared Thermal Mapper, including a morning delay in the post-dawn temperature rise and an enhanced cooling in the afternoon relative to any ideal, homogeneous model. The enhanced afternoon cooling observed at the Viking-1 landing site is reproduced by the non-ideal models while that atop Arsia Mons volcano is not, but may be attributed to the observing geometry.

  12. Importance of initial buoyancy field on evolution of mantle thermal structure: Implications of surface boundary conditions

    Directory of Open Access Journals (Sweden)

    Petar Glišović

    2015-01-01

    Full Text Available Although there has been significant progress in the seismic imaging of mantle heterogeneity, the outstanding issue that remains to be resolved is the unknown distribution of mantle temperature anomalies in the distant geological past that give rise to the present-day anomalies inferred by global tomography models. To address this question, we present 3-D convection models in compressible and self-gravitating mantle initialised by different hypothetical temperature patterns. A notable feature of our forward convection modelling is the use of self-consistent coupling of the motion of surface tectonic plates to the underlying mantle flow, without imposing prescribed surface velocities (i.e., plate-like boundary condition. As an approximation for the surface mechanical conditions before plate tectonics began to operate we employ the no-slip (rigid boundary condition. A rigid boundary condition demonstrates that the initial thermally-dominated structure is preserved, and its geographical location is fixed during the evolution of mantle flow. Considering the impact of different assumed surface boundary conditions (rigid and plate-like on the evolution of thermal heterogeneity in the mantle we suggest that the intrinsic buoyancy of seven superplumes is most-likely resolved in the tomographic images of present-day mantle thermal structure. Our convection simulations with a plate-like boundary condition reveal that the evolution of an initial cold anomaly beneath the Java-Indonesian trench system yields a long-term, stable pattern of thermal heterogeneity in the lowermost mantle that resembles the present-day Large Low Shear Velocity Provinces (LLSVPs, especially below the Pacific. The evolution of subduction zones may be, however, influenced by the mantle-wide flow driven by deeply-rooted and long-lived superplumes since Archean times. These convection models also detect the intrinsic buoyancy of the Perm Anomaly that has been identified as a unique

  13. Methods for coating conduit interior surfaces utilizing a thermal spray gun with extension arm

    Science.gov (United States)

    Moore, Karen A.; Zatorski, Raymond A.

    2007-10-02

    Systems and methods for applying a coating to an interior surface of a conduit. In one embodiment, a spray gun configured to apply a coating is attached to an extension arm which may be inserted into the bore of a pipe. The spray gun may be a thermal spray gun adapted to apply a powder coating. An evacuation system may be used to provide a volume area of reduced air pressure for drawing overspray out of the pipe interior during coating. The extension arm as well as the spray gun may be cooled to maintain a consistent temperature in the system, allowing for more consistent coating.

  14. Microstructure Analysis of Laser Remelting for Thermal Barrier Coatings on the Surface of Titanium Alloy

    Directory of Open Access Journals (Sweden)

    Lu Bin

    2016-01-01

    Full Text Available In this paper, the preparation and organization performance of thermal barrier coatings (TCBs on the surface of titanium were studied experimentally. Nanostructured 8 wt% yttria partially stabilized zirconia coatings were deposited by air plasma spraying. The microstructure of nanostructured and the conventional coating was studied after laser remelting. It has shown that formed a network of micro-cracks and pits after laser remelting on nanostructured coatings. With the decrease of the laser scanning speed, mesh distribution of micro cracks was gradually thinning on nanostructured coatings. Compared with conventional ceramic layers, the mesh cracks of nanostructured coating is dense and the crack width is small.

  15. Crossover from shear-driven to thermally activated drainage of liquid-infused microscale capillaries

    Science.gov (United States)

    Colosqui, Carlos E.; Wexler, Jason S.; Liu, Ying; Stone, Howard A.

    2016-10-01

    The shear-driven drainage of capillary grooves filled with viscous liquid is a dynamic wetting phenomenon relevant to numerous industrial processes and lubricant-infused surfaces for drag reduction and antifouling. Prior work has reported that a finite length L∞ of the capillary groove can remain indefinitely filled with liquid even when large shear stresses are applied. The mechanism preventing full drainage is attributed to a balance between the shear-driven flow and a counterflow driven by capillary pressures caused by deformation of the free surface. In this work, we examine closely the approach to the final equilibrium length L∞ and report a crossover to a slow drainage regime that cannot be described by conventional dynamic models considering solely hydrodynamic and capillary forces. The slow drainage regime observed in experiments can be instead modeled by a kinetic equation describing a sequence of random thermally activated transitions between multiple metastable states caused by surface defects with nanoscale dimensions. Our findings provide insights on the critical role that natural or engineered surface roughness with nanoscale dimensions can play in the imbibition and drainage of capillaries and other dynamic wetting processes in microscale systems.

  16. Structure dependence of Pt surface activated ammonia oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Santen, R A van; Offermans, W K [Schuit Institute of Catalysis, Laboratory of Inorganic Chemistry and Catalysis, Department of Chemical Engineering and Chemistry, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Ricart, J M; Novell-Leruth, G [Department of Chemical Physics and Inorganic Chemistry, University Rovira I Virgili, C/ Marcel.lI Domingo s/n, 43007 Tarragona (Spain); Perez-RamIrez, J [Institute of Chemical Research of Catalonia (ICIQ) and Catalan, Institution for Research and Advanced Studies (ICREA), Avinguda Paisos Catalans 16, 43007, Tarragona (Spain)], E-mail: r.a.v.santen@tue.nl

    2008-06-01

    Computational advances that enable the prediction of the structures and the energies of surface reaction intermediates are providing essential information to the formulation of theories of surface chemical reactivity. In this contribution this is illustrated for the activation of ammonia by coadsorbed oxygen and hydroxyl on the Pt(111), Pt(100), and Pt(211) surfaces.

  17. Experimental measurement of surface temperatures during flame-jet induced thermal spallation

    Science.gov (United States)

    Wilkinson, M. A.; Tester, J. W.

    1993-01-01

    Thermal spallation is a method whereby the surface of a rock is rapidly heated causing small (100 1000 μm) flakes or spalls, to form. When applied to drilling, a supersonic, high temperature (2600 K) gas jet is directed at the rock to provide the heat source and sweep away the spalls. Previous studies of thermal spallation drilling indicate that penetration rates of up to 30 m/hr (100 ft/hr), approximately ten times greater than commonly obtained using conventional rotary mechanical methods, can be achieved in competent, non-fractured hard rock such as granite. A total direct operating cost for drilling in granite using a flame-jet spallation drill was estimated by Browning (1981) to be approximately 9/m in 1991 (about 3/ft) compared to “trouble-free” well drilling costs for conventional rotary methods in similar rock to depths of 3 to 7 km (10000 to 21000 ft) of 300 to 900/m (100 to 300/ft) (Tester and Herzog, 1990, 1992). The Browning estimates for spallation drilling are obviously optimistic in that they don't include capital costs for the rig and associated hardware. However, the substantially higher penetration rates, significantly reduced wear of downhole components, and the high efficiency of rock communition in comparison to rotary methods suggest that substantial cost reductions could be possible in deep drilling applications. For example, in the construction of hot dry rock geothermal power plants where rotary mechanical methods are used for well drilling to depths of (4 to 5 km), about half of the initial capital cost would be required for well drilling alone (Tester and Herzog, 1992). The current study has focused on gaining a better understanding of both the rock failure mechanism that occurs during thermal spallation and the heat transfer from the gas jet to the rock surface. Rock mechanics modeling leads to an expression for the surface temperature during spallation as a function of rock physical properties and the incident heat flux. Surface

  18. Estimation of high-resolution near-surface freeze/thaw state by the integration of microwave and thermal infrared remote sensing data on the Tibetan Plateau

    Science.gov (United States)

    Zhao, Tianjie; Shi, Jiancheng; Hu, Tongxi; Zhao, Lin; Zou, Defu; Wang, Tianxing; Ji, Dabin; Li, Rui; Wang, Pingkai

    2017-08-01

    The objective of this study is to investigate how the complementarity between microwave and thermal infrared remote sensing can be exploited for a high-resolution near-surface freeze/thaw state estimation. The basic idea is to establish a feasible relationship between the microwave-derived freeze/thaw state and thermal infrared observations. A quantitative freeze/thaw index from microwave observations at 18.7 and 36.5 GHz is innovatively defined and is assumed to be linearly correlated with land surface temperature from thermal infrared observations. Thus, a linear regression method is proposed and verified to be effective over a multiscale network of Naqu of the Tibetan Plateau. In order to demonstrate the potentiality of the proposed method, it is implemented in the entire Tibetan Plateau. It is found that the linear relationship is quite reliable for most areas and can obtain a high-resolution near-surface soil freeze/thaw state with integrated information from microwave and thermal infrared remote sensing. The validation of the high-resolution freeze/thaw state against soil temperature measured at active layer monitoring sites along the Qinghai-Tibet Highway illustrates a moderate accuracy over a decade scale. This study provides new insights for high-resolution freeze/thaw mapping beyond the Soil Moisture Active Passive mission.

  19. Signal Modulation of Super Read Only Memory with Thermally Activated Aperture Model

    Science.gov (United States)

    Kim, June Seo; Kwak, Keumcheol; You, Chun-Yeol

    2008-07-01

    We describe the signal modulation of super read only memory (ROM) with thermally activated aperture model using a three-dimensional finite-difference time-domain method. The thermally activated aperture is modeled using a spatially varied refractive indices of the GeSbTe layer. No meaningful signal modulation is observed without thermally activated aperture below the resolution limit of 120 nm. When we open the thermally activated aperture by considering the temperature dependence of the refractive indices in the GeSbTe layer, the 2.8 and 1.7% signal modulations are observed for 120 and 80 nm pits, respectively. The experimentally observed signal modulation under the resolution limit can be explained using the thermally activated aperture model.

  20. Low thermal budget n-type doping into Ge(001) surface using ultraviolet laser irradiation in phosphoric acid solution

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, Kouta, E-mail: ktakahas@alice.xtal.nagoya-u.ac.jp, E-mail: kurosawa@alice.xtal.nagoya-u.ac.jp; Sakashita, Mitsuo; Takeuchi, Wakana; Nakatsuka, Osamu [Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Kurosawa, Masashi, E-mail: ktakahas@alice.xtal.nagoya-u.ac.jp, E-mail: kurosawa@alice.xtal.nagoya-u.ac.jp [Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Institute of Materials and Systems for Sustainability, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Institute for Advanced Research, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8601 (Japan); Ikenoue, Hiroshi [Graduate School of Information Science and Electrical Engineering, Kyushu University, 744 Motooka, Fukuoka 819-0395 (Japan); Zaima, Shigeaki [Graduate School of Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Institute of Materials and Systems for Sustainability, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan)

    2016-02-01

    We have investigated phosphorus (P) doping into Ge(001) surfaces by using ultraviolet laser irradiation in phosphoric acid solution at room temperature. We demonstrated that the diffusion depth of P in Ge and the concentration of electrically activated P can be controlled by the number of laser shots. Indeed, a high concentration of electrically activated P of 2.4 × 10{sup 19} cm{sup −3} was realized by 1000-times laser shots at a laser energy of 1.0 J/cm{sup 2}, which is comparable or better than the counterparts of conventional n-type doping using a high thermal budget over 600 °C. The generation current is dominant in the reverse bias condition for the laser-doped pn-junction diodes independent on the number of laser shots, thus indicating low-damage during the pn-junction formation. These results open up the possibility for applicable low thermal budget doping process for Ge-based devices fabricated on flexible substrates as well as Si electronics.

  1. A new surface catalytic model for silica-based thermal protection material for hypersonic vehicles

    Directory of Open Access Journals (Sweden)

    Li Kai

    2015-10-01

    Full Text Available Silica-based materials are widely employed in the thermal protection system for hypersonic vehicles, and the investigation of their catalytic characteristics is crucially important for accurate aerothermal heating prediction. By analyzing the disadvantages of Norman’s high and low temperature models, this paper combines the two models and proposes an eight-reaction combined surface catalytic model to describe the catalysis between oxygen and silica surface. Given proper evaluation of the parameters according to many references, the recombination coefficient obtained shows good agreement with experimental data. The catalytic mechanisms between oxygen and silica surface are then analyzed. Results show that with the increase of the wall temperature, the dominant reaction contributing to catalytic coefficient varies from Langmuir–Hinshelwood (LH recombination (TW  1350 K. The surface coverage of chemisorption areas varies evidently with the dominant reactions in the high temperature (HT range, while the surface coverage of physisorption areas varies within quite low temperature (LT range (TW < 250 K. Recommended evaluation of partial parameters is also given.

  2. Estimation of surface heat flux for ablation and charring of thermal protection material

    Science.gov (United States)

    Qian, Wei-qi; He, Kai-feng; Zhou, Yu

    2016-07-01

    Ablation of the thermal protection material of the reentry hypersonic flight vehicle is a complex physical and chemical process. To estimate the surface heat flux from internal temperature measurement is much more complex than the conventional inverse heat conduction problem case. In the paper, by utilizing a two-layer pyrogeneration-plane ablation model to model the ablation and charring of the material, modifying the finite control volume method to suit for the numerical simulation of the heat conduction equation with variable-geometry, the CGM along with the associated adjoint problem is developed to estimate the surface heat flux. This estimation method is verified with a numerical example at first, the results show that the estimation method is feasible and robust. The larger is the measurement noise, the greater is the deviation of the estimated result from the exact value, and the measurement noise of ablated surface position has a significant and more direct influence on the estimated result of surface heat flux. Furthermore, the estimation method is used to analyze the experimental data of ablation of blunt Carbon-phenolic material Narmco4028 in an arc-heater. It is shown that the estimated surface heat flux agrees with the heating power value of the arc-heater, and the estimation method is basically effective and potential to treat the engineering heat conduction problem with ablation.

  3. Sperm cell surface dynamics during activation and fertilization

    NARCIS (Netherlands)

    Boerke, A.

    2013-01-01

    Before the sperm cell can reach the oocyte it needs to be activated and to undergo a series of preparative steps. The sperm surface dynamics was studied in relation to this activation process and the modifications and removal of sperm surface components havebeen investigated. Bicarbonate-induced rad

  4. Post Irradiation Evaluation of Thermal Control Coatings and Solid Lubricants to Support Fission Surface Power Systems

    Science.gov (United States)

    Bowman, Cheryl L.; Jaworske, Donald A.; Stanford, Malcolm K.; Persinger, Justin A.; Khorsandi, Behrooz; Blue, Thomas E.

    2007-01-01

    The development of a nuclear power system for space missions, such as the Jupiter Icy Moons Orbiter or a lunar outpost, requires substantially more compact reactor design than conventional terrestrial systems. In order to minimize shielding requirements and hence system weight, the radiation tolerance of component materials within the power conversion and heat rejection systems must be defined. Two classes of coatings, thermal control paints and solid lubricants, were identified as material systems for which limited radiation hardness information was available. Screening studies were designed to explore candidate coatings under a predominately fast neutron spectrum. The Ohio State Research Reactor Facility staff performed irradiation in a well characterized, mixed energy spectrum and performed post irradiation analysis of representative coatings for thermal control and solid lubricant applications. Thermal control paints were evaluated for 1 MeV equivalent fluences from 1013 to 1015 n/cm2. No optical degradation was noted although some adhesive degradation was found at higher fluence levels. Solid lubricant coatings were evaluated for 1 MeV equivalent fluences from 1015 to 1016 n/cm2 with coating adhesion and flexibility used for post irradiation evaluation screening. The exposures studied did not lead to obvious property degradation indicating the coatings would have survived the radiation environment for the previously proposed Jupiter mission. The results are also applicable to space power development programs such as fission surface power for future lunar and Mars missions.

  5. Surface Study of Carbon Nanotubes Prepared by Thermal-CVD of Camphor Precursor

    Science.gov (United States)

    Azira, A. A.; Rusop, M.

    2010-03-01

    Surface morphology study on the influence of starting carbon materials by using thermal chemical vapor deposition (Thermal-CVD) to produced carbon nanotubes (CNTs) is investigated. The CNTs derived from camphor were synthesized as the precursor material due to low sublimation temperature, which indirectly maybe cost effective. The major parameters are also evaluated in order to obtain high-yield and high-quality CNTs. The prepared CNTs are examined using field emission scanning electron microscopy (FESEM) and high resolution transmission electron microscope (HR-TEM) to determine the microstructure of nanocarbons. The FESEM investigation of the CNTs formed on the support catalysts provides evidence that camphor is suitable as a precursor material for nanotubes formation. The high-temperature graphitization process induced by the Thermal-CVD enables the hydrocarbons to act as carbon sources and changes the aromatic species into the layered graphite structure of CNTs. The camphoric hydrocarbons not only found acts as the precursors but also enhances the production rate and the quality of CNTs.

  6. Post Irradiation Evaluation of Thermal Control Coatings and Solid Lubricants to Support Fission Surface Power Systems

    Science.gov (United States)

    Bowman, Cheryl L.; Jaworske, Donald A.; Stanford, Malcolm K.; Persinger, Justin A.; Khorsandi, Behrooz; Blue, Thomas E.

    2007-01-01

    The development of a nuclear power system for space missions, such as the Jupiter Icy Moons Orbiter or a lunar outpost, requires substantially more compact reactor design than conventional terrestrial systems. In order to minimize shielding requirements and hence system weight, the radiation tolerance of component materials within the power conversion and heat rejection systems must be defined. Two classes of coatings, thermal control paints and solid lubricants, were identified as material systems for which limited radiation hardness information was available. Screening studies were designed to explore candidate coatings under a predominately fast neutron spectrum. The Ohio State Research Reactor Facility staff performed irradiation in a well characterized, mixed energy spectrum and performed post irradiation analysis of representative coatings for thermal control and solid lubricant applications. Thermal control paints were evaluated for 1 MeV equivalent fluences from 10(exp 13) to 10(exp 15) n per square centimeters. No optical degradation was noted although some adhesive degradation was found at higher fluence levels. Solid lubricant coatings were evaluated for 1 MeV equivalent fluences from 10(exp 15) to 10(exp 16) n per square centimeters with coating adhesion and flexibility used for post irradiation evaluation screening. The exposures studied did not lead to obvious property degradation indicating the coatings would have survived the radiation environment for the previously proposed Jupiter mission. The results are also applicable to space power development programs such as fission surface power for future lunar and Mars missions.

  7. Surface, thermal, and mechanical properties of composites and nanocomposites of polyurethane/PTFE nanoparticles

    Science.gov (United States)

    Anbinder, P. S.; Peruzzo, P. J.; de Siervo, A.; Amalvy, J. I.

    2014-08-01

    Films from blends of polyurethane and nano-polytetrafluoroethylene aqueous dispersions (PU/nanoPTFE) were prepared, and the effect of the addition of different amounts of PTFE nanoparticles (50 nm) was studied. The changes in the superficial properties of the films were studied by means of XPS, ATR/FTIR, and contact angle measurements. SEM and TEM results are also included. The contact angle values confirm the surface hydrophobicity of composite films. Even though nanoparticles are present in the bulk, higher concentrations of particles appear at the surface in samples with lower nanoPTFE content (up to 10 wt%), as revealed by XPS. Higher amounts of nanoPTFE particles cause aggregation. The mechanical and thermal properties of composites are also discussed.

  8. The influence of surface functionalisation on the electrical properties and thermal stability of nanodiamonds

    Energy Technology Data Exchange (ETDEWEB)

    Welch, Joseph O; Li, Pei; Chaudhary, Aysha; Edgington, Robert; Jackman, Richard B., E-mail: r.jackman@ucl.ac.uk [London Centre for Nanotechnology and the Department of Electronic and Electrical Engineering, University College London, 17-19 Gordon Street, London WC1H 0AH (United Kingdom)

    2014-10-07

    Detonation nanodiamond (ND) has recently emerged as a useful new class of diamond material. However, to date there has been little investigation of the electrical properties of this material. Due to the nanoscale dimensions, the surface functionalisation of the individual ND is of particular importance to the characteristics of ND films. Here, hydrogen and oxygen termination of ND, verified using Fourier transform infrared spectroscopy, are shown to strongly influence the electronic properties of NDs. Hydrogen terminated ND exhibiting a far greater resilience to thermal decomposition when compared to the oxygen terminated NDs. Moreover, H-NDs also displayed so-called “surface conductivity,” a property displayed by hydrogen-terminated bulk diamond films, whilst O-NDs display properties high resistivity. These results indicate that under the correct conditions ND layers can display similar electrical properties to “bulk” diamond thin films.

  9. The influence of surface functionalisation on the electrical properties and thermal stability of nanodiamonds

    Science.gov (United States)

    Welch, Joseph O.; Li, Pei; Chaudhary, Aysha; Edgington, Robert; Jackman, Richard B.

    2014-10-01

    Detonation nanodiamond (ND) has recently emerged as a useful new class of diamond material. However, to date there has been little investigation of the electrical properties of this material. Due to the nanoscale dimensions, the surface functionalisation of the individual ND is of particular importance to the characteristics of ND films. Here, hydrogen and oxygen termination of ND, verified using Fourier transform infrared spectroscopy, are shown to strongly influence the electronic properties of NDs. Hydrogen terminated ND exhibiting a far greater resilience to thermal decomposition when compared to the oxygen terminated NDs. Moreover, H-NDs also displayed so-called "surface conductivity," a property displayed by hydrogen-terminated bulk diamond films, whilst O-NDs display properties high resistivity. These results indicate that under the correct conditions ND layers can display similar electrical properties to "bulk" diamond thin films.

  10. Crystalline silicon surface passivation by thermal ALD deposited Al doped ZnO thin films

    Directory of Open Access Journals (Sweden)

    Jagannath Panigrahi

    2017-03-01

    Full Text Available The evidence of good quality silicon surface passivation using thermal ALD deposited Al doped zinc oxide (AZO thin films is demonstrated. AZO films are prepared by introducing aluminium precursor in between zinc and oxygen precursors during the deposition. The formation of AZO is confirmed by ellipsometry, XRD and Hall measurements. Effective minority carrier lifetime (τeff greater than 1.5ms at intermediate bulk injection levels is realized for symmetrically passivated p-type silicon surfaces under optimised annealing conditions of temperature and time in hydrogen ambient. The best results are realised at 450°C annealing for >15min. Such a layer may lead to implied open circuit voltage gain of 80mV.

  11. Thermal Analysis of Unusual Local-scale Features on the Surface of Vesta

    Science.gov (United States)

    Tosi, F.; Capria, M. T.; DeSanctis, M. C.; Capaccioni, F.; Palomba, E.; Zambon, F.; Ammannito, E.; Blewett, D. T.; Combe, J.-Ph.; Denevi, B. W.; Li, J.-Y.; Mittlefehldt, D. W.; Palmer, E.; Sunshine, J. M.; Titus, T. N.; Raymond, C. A.; Russell, C. T.

    2013-01-01

    At 525 km in mean diameter, Vesta is the second-most massive object in the main asteroid belt of our Solar System. At all scales, pyroxene absorptions are the most prominent spectral features on Vesta and overall, Vesta mineralogy indicates a complex magmatic evolution that led to a differentiated crust and mantle [1]. The thermal behavior of areas of unusual albedo seen on the surface at the local scale can be related to physical properties that can provide information about the origin of those materials. Dawn's Visible and Infrared Mapping Spectrometer (VIR) [2] hyperspectral images are routinely used, by means of temperature-retrieval algorithms, to compute surface temperatures along with spectral emissivities. Here we present temperature maps of several local-scale features of Vesta that were observed by Dawn under different illumination conditions and different local solar times.

  12. Evaluation of lateral resolution of scanning surface microscopy by total internal reflection with thermal lens effect.

    Science.gov (United States)

    Shimosaka, Takuya; Izako, Masakazu; Uchiyama, Katsumi; Hobo, Toshiyuki

    2003-06-01

    We have developed a novel method for in situ and non-destructive surface analyses, or a total internal reflection with thermal lens spectroscopy (TIR-TLS), which has sufficient sensitivity to monitor phenomena in thin films, such as lipid bilayers. In this study, we applied TIR-TLS to microscopy for surface analyses, and we experimentally obtained its lateral resolution using the edge of a chromium film made by a photolithography technique. The obtained resolution was 20 microm, which was 60% of the diameter of an excitation beam at the interface. The estimated resolution with a simple model agreed with the experimental one, and from this model, TIR-TLS microscopy has the same resolution as that of ordinary optical microscopy. The microscopy by TIR-TLS was applied to a sample whose contrast was too weak to be visually seen, and an image of the sample was obtained without any loss of resolution.

  13. EFFECTS OF BLENDING CHITOSAN WITH PEG ON SURFACE MORPHOLOGY,CRYSTALLIZATION AND THERMAL PROPERTIES

    Institute of Scientific and Technical Information of China (English)

    Ling-hao He; Rui Xue; De-bin Yang; Ying Liu; Rui Song

    2009-01-01

    Biodegradable blend films composed of chitosan and PEG with various composition ratios were prepared. The chemical structure of the blend films was characterized with FTIR and X-ray, which showed no chemical bond formations but certain interactions probably coming from the hydrogen bonds. Morphologies of these blend films were viewed using AFM and SEM, suggesting that pure chitosan film had a smooth surface structure and the blend films surface showed a plenty of holes with varying size. Through the DMA measurement, it was found that there existed differences in the peak area and position of the blend films, and the peak at the glass transition temperature became significantly weaker and was markedly wider with the increasing content of PEG. The obtained results showed that the crystallinity of chitosan was suppressed and partially destroyed; and this should have an influence on the thermal behaviors and dynamic mechanical properties of the blend films.

  14. Coordinated surface activities in Variovorax paradoxus EPS

    Directory of Open Access Journals (Sweden)

    Gregory Glenn A

    2009-06-01

    Full Text Available Abstract Background Variovorax paradoxus is an aerobic soil bacterium frequently associated with important biodegradative processes in nature. Our group has cultivated a mucoid strain of Variovorax paradoxus for study as a model of bacterial development and response to environmental conditions. Colonies of this organism vary widely in appearance depending on agar plate type. Results Surface motility was observed on minimal defined agar plates with 0.5% agarose, similar in nature to swarming motility identified in Pseudomonas aeruginosa PAO1. We examined this motility under several culture conditions, including inhibition of flagellar motility using Congo Red. We demonstrated that the presence of a wetting agent, mineral, and nutrient content of the media altered the swarming phenotype. We also demonstrated that the wetting agent reduces the surface tension of the agar. We were able to directly observe the presence of the wetting agent in the presence and absence of Congo Red, and found that incubation in a humidified chamber inhibited the production of wetting agent, and also slowed the progression of the swarming colony. We observed that swarming was related to both carbon and nitrogen sources, as well as mineral salts base. The phosphate concentration of the mineral base was critical for growth and swarming on glucose, but not succinate. Swarming on other carbon sources was generally only observed using M9 salts mineral base. Rapid swarming was observed on malic acid, d-sorbitol, casamino acids, and succinate. Swarming at a lower but still detectable rate was observed on glucose and sucrose, with weak swarming on maltose. Nitrogen source tests using succinate as carbon source demonstrated two distinct forms of swarming, with very different macroscopic swarm characteristics. Rapid swarming was observed when ammonium ion was provided as nitrogen source, as well as when histidine, tryptophan, or glycine was provided. Slower swarming was observed

  15. Coordinated surface activities in Variovorax paradoxus EPS.

    Science.gov (United States)

    Jamieson, W David; Pehl, Michael J; Gregory, Glenn A; Orwin, Paul M

    2009-06-12

    Variovorax paradoxus is an aerobic soil bacterium frequently associated with important biodegradative processes in nature. Our group has cultivated a mucoid strain of Variovorax paradoxus for study as a model of bacterial development and response to environmental conditions. Colonies of this organism vary widely in appearance depending on agar plate type. Surface motility was observed on minimal defined agar plates with 0.5% agarose, similar in nature to swarming motility identified in Pseudomonas aeruginosa PAO1. We examined this motility under several culture conditions, including inhibition of flagellar motility using Congo Red. We demonstrated that the presence of a wetting agent, mineral, and nutrient content of the media altered the swarming phenotype. We also demonstrated that the wetting agent reduces the surface tension of the agar. We were able to directly observe the presence of the wetting agent in the presence and absence of Congo Red, and found that incubation in a humidified chamber inhibited the production of wetting agent, and also slowed the progression of the swarming colony. We observed that swarming was related to both carbon and nitrogen sources, as well as mineral salts base. The phosphate concentration of the mineral base was critical for growth and swarming on glucose, but not succinate. Swarming on other carbon sources was generally only observed using M9 salts mineral base. Rapid swarming was observed on malic acid, d-sorbitol, casamino acids, and succinate. Swarming at a lower but still detectable rate was observed on glucose and sucrose, with weak swarming on maltose. Nitrogen source tests using succinate as carbon source demonstrated two distinct forms of swarming, with very different macroscopic swarm characteristics. Rapid swarming was observed when ammonium ion was provided as nitrogen source, as well as when histidine, tryptophan, or glycine was provided. Slower swarming was observed with methionine, arginine, or tyrosine. Large

  16. Shape, thermal and surface properties determination of a candidate spacecraft target asteroid (175706) 1996 FG3

    Science.gov (United States)

    Yu, LiangLiang; Ji, Jianghui; Wang, Su

    2014-04-01

    In this paper, a 3D convex shape model of (175706) 1996 FG3, which consists of 2040 triangle facets and 1022 vertices, is derived from the known light curves. The best-fitting orientation of the asteroid's spin axis is determined to be λ = 237.27° and β = -83.8° considering the observation uncertainties, and its rotation period is ˜3.5935 h. Using the derived shape model, we adopt the so-called advanced thermophysical model (ATPM) to fit three published sets of mid-infrared observations of 1996 FG3, so as to evaluate its surface properties. Assuming the primary and the secondary bear identical shape, albedo, thermal inertia and surface roughness, the best-fitting parameters are obtained from the observations. The geometric albedo and effective diameter of the asteroid are reckoned to be pv = 0.045 ± 0.002, D_eff=1.69^{+0.05}_{-0.02} km. The diameters of the primary and secondary are determined to be D1=1.63^{+0.04}_{-0.03} km and D2=0.45^{+0.04}_{-0.03} km, respectively. The surface thermal inertia Γ is derived to be a low value of 80 ± 40 Jm-2 s-0.5 K-1 with a roughness fraction fR of 0.8^{+0.2}_{-0.4}. This indicates that the primary possibly has a regolith layer on its surface, which is likely to be covered by a mixture of dust, fragmentary rocky debris and sand. The minimum regolith depth is estimated to be 5-20 mm from the simulations of subsurface temperature distribution, indicating that 1996 FG3 could be a very suitable target for a sample return mission.

  17. Stability of silanols and grafted alkylsilane monolayers on plasma-activated mica surfaces.

    Science.gov (United States)

    Liberelle, Benoît; Banquy, Xavier; Giasson, Suzanne

    2008-04-01

    We investigated the effect of physical and chemical modifications of mica surfaces induced by water vapor-based plasma treatments on the stability of silanols and grafted alkylsilane monolayers. The plasma-activated substrates were characterized using XPS, TOF-SIMS, and contact angle measurements. They revealed a large surface coverage of silanol groups (Si-OH) and a loss of aluminum atoms compared to freshly cleaved mica surfaces. The stability of plasma-induced silanol groups was investigated by contact angle measurements using ethylene glycol as a probe liquid. The Si-OH surface coverage decreased rapidly under vacuum or thermal treatment to give rise to hydrophobic dehydrated surfaces. The stability of end-grafted monofunctionalized n-alkylsilanes was investigated in different solvents and at different pH using water contact angle measurements. The degrafting of alkylsilanes from the activated mica was promoted in acidic aqueous solutions. This detachment was associated with the hydrolysis of covalent bonds between the alkylsilanes and the mica surface. The monolayer stability was enhanced by increasing the length of the alkyl chains that probably act as a hydrophobic protective layer against hydrolysis reactions. Stable alkylsilane monolayers in water with pH greater than 5.5 were obtained on mica surfaces activated at low plasma pressure. We attributed this stability to the loss of surface Al atoms induced by the plasma treatment.

  18. Specific Features of Chip Making and Work-piece Surface Layer Formation in Machining Thermal Coatings

    Directory of Open Access Journals (Sweden)

    V. M. Yaroslavtsev

    2016-01-01

    Full Text Available A wide range of unique engineering structural and performance properties inherent in metallic composites characterizes wear- and erosion-resistant high-temperature coatings made by thermal spraying methods. This allows their use both in manufacturing processes to enhance the wear strength of products, which have to operate under the cyclic loading, high contact pressures, corrosion and high temperatures and in product renewal.Thermal coatings contribute to the qualitative improvement of the technical level of production and product restoration using the ceramic composite materials. However, the possibility to have a significantly increased product performance, reduce their factory labour hours and materials/output ratio in manufacturing and restoration is largely dependent on the degree of the surface layer quality of products at their finishing stage, which is usually provided by different kinds of machining.When machining the plasma-sprayed thermal coatings, a removing process of the cut-off layer material is determined by its distinctive features such as a layered structure, high internal stresses, low ductility material, high tendency to the surface layer strengthening and rehardening, porosity, high abrasive properties, etc. When coatings are machined these coating properties result in specific characteristics of chip formation and conditions for formation of the billet surface layer.The chip formation of plasma-sprayed coatings was studied at micro-velocities using an experimental tool-setting microscope-based setup, created in BMSTU. The setup allowed simultaneous recording both the individual stages (phases of the chip formation process and the operating force factors.It is found that formation of individual chip elements comes with the multiple micro-cracks that cause chipping-off the small particles of material. The emerging main crack in the cut-off layer of material leads to separation of the largest chip element. Then all the stages

  19. AURORA: A FORTRAN program for modeling well stirred plasma and thermal reactors with gas and surface reactions

    Energy Technology Data Exchange (ETDEWEB)

    Meeks, E.; Grcar, J.F.; Kee, R.J. [Sandia National Labs., Livermore, CA (United States). Thermal and Plasma Processes Dept.; Moffat, H.K. [Sandia National Labs., Albuquerque, NM (United States). Surface Processing Sciences Dept.

    1996-02-01

    The AURORA Software is a FORTRAN computer program that predicts the steady-state or time-averaged properties of a well mixed or perfectly stirred reactor for plasma or thermal chemistry systems. The software was based on the previously released software, SURFACE PSR which was written for application to thermal CVD reactor systems. AURORA allows modeling of non-thermal, plasma reactors with the determination of ion and electron concentrations and the electron temperature, in addition to the neutral radical species concentrations. Well stirred reactors are characterized by a reactor volume, residence time or mass flow rate, heat loss or gas temperature, surface area, surface temperature, the incoming temperature and mixture composition, as well as the power deposited into the plasma for non-thermal systems. The model described here accounts for finite-rate elementary chemical reactions both in the gas phase and on the surface. The governing equations are a system of nonlinear algebraic relations. The program solves these equations using a hybrid Newton/time-integration method embodied by the software package TWOPNT. The program runs in conjunction with the new CHEMKIN-III and SURFACE CHEMKIN-III packages, which handle the chemical reaction mechanisms for thermal and non-thermal systems. CHEMKIN-III allows for specification of electron-impact reactions, excitation losses, and elastic-collision losses for electrons.

  20. Maximizing the Use of Satellite Thermal Infrared Data for Advancing Land Surface Temperature Analysis

    Science.gov (United States)

    Weng, Q.; Fu, P.; Gao, F.

    2014-12-01

    Land surface temperature (LST) is a crucial parameter in investigating environmental, ecological processes and climate change at various scales, and is also valuable in the studies of evapotranspiration, soil moisture conditions, surface energy balance, and urban heat islands. These studies require thermal infrared (TIR) images at both high temporal and spatial resolution to retrieve LST. However, currently, no single satellite sensors can deliver TIR data at both high temporal and spatial resolution. Thus, various algorithms/models have been developed to enhance the spatial or the temporal resolution of TIR data, but rare of those can enhance both spatial and temporal details. This paper presents a new data fusion algorithm for producing Landsat-like LST data by blending daily MODIS and periodic Landsat TM datasets. The original Spatial and Temporal Adaptive Reflectance Fusion Model (STARFM) was improved and modified for predicting thermal radiance and LST data by considering annual temperature cycle (ATC) and urban thermal landscape heterogeneity. The technique of linear spectral mixture analysis was employed to relate the Landsat radiance with the MODIS one, so that the temporal changes in radiance can be incorporated in the fusion model. This paper details the theoretical basis and the implementation procedures of the proposed data fusion algorithm, Spatio-temporal Adaptive Data Fusion Algorithm for Temperature mapping (SADFAT). A case study was conducted that predicted LSTs of five dates in 2005 from July to October in Los Angeles County, California. The results indicate that the prediction accuracy for the whole study area ranged from 1.3 K to 2 K. Like existing spatio-temporal data fusion models, the SADFAT method has a limitation in predicting LST changes that were not recorded in the MODIS and/or Landsat pixels due to the model assumption.

  1. Electrically and thermally activated ageing mechanisms in metallised polymer film capacitors

    CERN Document Server

    Lee, Y P

    2001-01-01

    This dissertation describes a combined computational and experimental study to understand the fundamental electrostatic, thermal, electromagnetic, and discharge related processes during the ageing of metallised polymer film capacitors. In the event of internal breakdowns, these capacitors are capable of 'self-healing' through a controlled isolation of defects on the electrode surfaces by mosaic patterning the electrode. The objective of this project is to develop viable computer models to unravel electrothermally activated ageing processes in capacitors. To provide the necessary validation to any capacitor models developed, our work is supported by comprehensive experiments including industrial standard accelerated life tests and associated breakdown damage analyses of tested capacitors. These have enabled an empirical identification of main factors affecting the reliability and lifetime of capacitors. Relevant raw data and the qualitative picture enabled by these data are crucial to the development and refin...

  2. Emission of Polycyclic Aromatic Hydrocarbons from the Exhalation Zones of Thermally Active Mine Waste Dumps

    Directory of Open Access Journals (Sweden)

    Patrycja Kuna-Gwoździewicz

    2013-01-01

    Full Text Available The article presents results of research carried out on the occurrence of polycyclic aromatic hydrocarbons (PAH in gases of exhalation zones, created on the surface of a thermally active coal mine waste dump. The oxidation and self-heating of mine waste are accompanied with the intensive emission of flue gases, including PAH group compounds. Taking into consideration the fact the hydrocarbons show strong genotoxic, mutagenic and carcinogenic properties, research was conducted to establish their content in the examined gases. The research object was a gangue dump located in Rybnik. The research was performed in 2012. In total, 24 samples of gas were collected with PUF (polyurethane foam sampling cartridges with a quartz fibre filter and an aspirator. The collected samples were analysed with the use of high performance liquid chromatography (HPLC and a fluorescence detector (FLD to evaluate the amount of PAH present.

  3. Experimental investigations on active cooling thermal protection structure of hydrocarbon-fueled scramjet combustor in arc heated facility

    Science.gov (United States)

    Jianqiang, Tu; Jinlong, Peng; Xianning, Yang; Lianzhong, Chen

    2016-10-01

    The active cooling thermal protection technology is the efficient method to resolve the long-duration work and reusable problems of hydrocarbon-fueled scramjet combustor, where worst thermo-mechanical loads occur. The fuel is passed through coolant channels adjacent to the heated surfaces to absorb heat from the heating exchanger panels, prior to injection into the combustor. The heating exchanger both cooled down the wall temperature of the combustor wall and heats and cracks the hydrocarbon fuel inside the panel to permit an easier combustion and satisfying combustion efficiency. The subscale active cooling metallic panels, with dimensions of 100×100 mm and different coolant channel sizes, have been tested under typical combustion thermal environment produced by arc heated Turbulent Flow Duct (TFD). The heat exchange ability of different coolant channel sizes has been obtained. The big-scale active cooling metallic panel, with dimensions of 100 × 750 mm and the coolant channel sizes of better heating exchange performance, has been made and tested in the big-scale arc heated TFD facility. The test results show that the local superheated ablation is easy to happen for the cooling fuel assigned asymmetrically in the bigscale active cooling metallic panel, and the cooling fuel rate can reduce 8%˜10% after spraying the Thermal Barrier Coating (TBC) in the heating surface.

  4. Experimental thermal transport evolution of silane activated nano-clay reinforced styrene butadiene elastomeric nanocomposites

    Science.gov (United States)

    Iqbal, S. S.; Iqbal, N.; Jamil, T.; Bashir, A.; Shahid, M.

    2016-08-01

    In this study, silane activated nanoclay was reinforced in styrene butadiene rubber (SBR) to enhance the thermal resistance/stability and mechanical properties of SBR. silane activated nanoclay with variant concentrations was impregnated in the rubber matrix to fabricate polymer nanocomposites under control processing conditions. Experimental thermal transport, thermal oxidation, phase transition study, and mechanical properties of the nanocomposite specimens were carried out. Thermal insulation, thermal stability, and heat flow response were remarkably enhanced with the addition of nanokaolinite in the polymer matrix. Phase transition temperatures, their corresponding enthalpies, tensile strength, elastic modulus, elongation at break and hardness of the rubber composites were positively influenced with the filler incorporation into the host matrix. The Even dispersion of nanoreinforcements, morphological and compositional analyses of the thermal transport tested specimens were performed using scanning electron microscopy and energy dispersive spectroscopy, respectively.

  5. Surface evolution of polycarbonate/polyethylene terephthalate blends induced by thermal treatments

    Energy Technology Data Exchange (ETDEWEB)

    Licciardello, A.; Auditore, A.; Samperi, F.; Puglisi, C

    2003-01-15

    Bisphenol-A polycarbonate (PC) and polyethyleneterephthalate (PET) blends are known to undergo, upon thermal treatment (melt mixing), exchange reactions leading to the formation of copolymers having a final structure that is also affected by consecutive reactions involving CO{sub 2} and ethylene carbonate losses. In this work we followed the evolution of the surface composition of this system during the melt mixing at 270 deg. C, both with and without catalysts, by means of time-of-flight secondary ion mass spectroscopy (ToF-SIMS). The static SIMS spectra obtained at different treatment times show the appearance of peaks related to newly formed structures and also the modification of the relative intensities of peaks characteristic of both the initial constituents of the blend. From the variation of the relative intensities of peaks related to the bisphenol-A unit of PC and to the phthalate structure of PET, it is shown that after the first stages of melt mixing the surface is PC enriched and that with the progressive formation of a random copolymer the phthalate units increase their concentration at the surface of the system. Hence, as final result of the melt mixing process, the surface composition tends to reflect the relative amount of the repeating units in the bulk.

  6. Surface evolution of polycarbonate/polyethylene terephthalate blends induced by thermal treatments

    Science.gov (United States)

    Licciardello, A.; Auditore, A.; Samperi, F.; Puglisi, C.

    2003-01-01

    Bisphenol-A polycarbonate (PC) and polyethyleneterephthalate (PET) blends are known to undergo, upon thermal treatment (melt mixing), exchange reactions leading to the formation of copolymers having a final structure that is also affected by consecutive reactions involving CO 2 and ethylene carbonate losses. In this work we followed the evolution of the surface composition of this system during the melt mixing at 270 °C, both with and without catalysts, by means of time-of-flight secondary ion mass spectroscopy (ToF-SIMS). The static SIMS spectra obtained at different treatment times show the appearance of peaks related to newly formed structures and also the modification of the relative intensities of peaks characteristic of both the initial constituents of the blend. From the variation of the relative intensities of peaks related to the bisphenol-A unit of PC and to the phthalate structure of PET, it is shown that after the first stages of melt mixing the surface is PC enriched and that with the progressive formation of a random copolymer the phthalate units increase their concentration at the surface of the system. Hence, as final result of the melt mixing process, the surface composition tends to reflect the relative amount of the repeating units in the bulk.

  7. Modification of the cellulosic component of hemp fibers using sulfonic acid derivatives: Surface and thermal characterization.

    Science.gov (United States)

    George, Michael; Mussone, Paolo G; Bressler, David C

    2015-12-10

    The aim of this study was to characterize the surface, morphological, and thermal properties of hemp fibers treated with two commercially available, inexpensive, and water soluble sulfonic acid derivatives. Specifically, the cellulosic component of the fibers were targeted, because cellulose is not easily removed during chemical treatment. These acids have the potential to selectively transform the surfaces of natural fibers for composite applications. The proposed method proceeds in the absence of conventional organic solvents and high reaction temperatures. Surface chemical composition and signature were measured using gravimetric analysis, X-ray photoelectron spectroscopy (XPS) and Fourier transform infra-red spectroscopy (FTIR). XPS data from the treated hemp fibers were characterized by measuring the reduction in O/C ratio and an increase in abundance of the C-C-O signature. FTIR confirmed the reaction with the emergence of peaks characteristic of disubstituted benzene and amino groups. Grafting of the sulfonic derivatives resulted in lower surface polarity. Thermogravimetric analysis revealed that treated fibers were characterized by lower percent degradation between 200 and 300 °C, and a higher initial degradation temperature.

  8. Relation between the Atmospheric Boundary Layer and Impact Factors under Severe Surface Thermal Conditions

    Directory of Open Access Journals (Sweden)

    Yinhuan Ao

    2017-01-01

    Full Text Available This paper reported a comprehensive analysis on the diurnal variation of the Atmospheric Boundary Layer (ABL in summer of Badain Jaran Desert and discussed deeply the effect of surface thermal to ABL, including the Difference in Surface-Air Temperature (DSAT, net radiation, and sensible heat, based on limited GPS radiosonde and surface observation data during two intense observation periods of experiments. The results showed that (1 affected by topography of the Tibetan Plateau, the climate provided favorable external conditions for the development of Convective Boundary Layer (CBL, (2 deep CBL showed a diurnal variation of three- to five-layer structure in clear days and five-layer ABL structure often occurred about sunset or sunrise, (3 the diurnal variation of DSAT influenced thickness of ABL through changes of turbulent heat flux, (4 integral value of sensible heat which rapidly converted by surface net radiation had a significant influence on the growth of CBL throughout daytime. The cumulative effect of thick RML dominated the role after CBL got through SBL in the development stage, especially in late summer, and (5 the development of CBL was promoted and accelerated by the variation of wind field and distribution of warm advection in high and low altitude.

  9. Effect of Simulant Type on the Absorptance and Emittance of Dusted Thermal Control Surfaces in a Simulated Lunar Environment

    Science.gov (United States)

    Gaier, James R.

    2010-01-01

    During the Apollo program the effects of lunar dust on thermal control surfaces was found to be more significant than anticipated, with several systems overheating due to deposition of dust on them. In an effort to reduce risk to future missions, a series of tests has been initiated to characterize the effects of dust on these surfaces, and then to develop technologies to mitigate that risk. Given the variations in albedo across the lunar surface, one variable that may be important is the darkness of the lunar dust, and this study was undertaken to address that concern. Three thermal control surfaces, AZ-93 white paint and AgFEP and AlFEP second surface mirrors were dusted with three different lunar dust simulants in a simulated lunar environment, and their integrated solar absorptance ( ) and thermal emittance ( ) values determined experimentally. The three simulants included JSC-1AF, a darker mare simulant, NU-LHT-1D, a light highlands simulant, and 1:1 mixture of the two. The response of AZ-93 was found to be slightly more pronounced than that of AgFEP. The increased with fractional dust coverage in both types of samples by a factor of 1.7 to 3.3, depending on the type of thermal control surface and the type of dust. The of the AZ-93 decreased by about 10 percent when fully covered by dust, while that of AgFEP increased by about 10 percent. It was found that / varied by more than a factor of two depending on the thermal control surface and the darkness of the dust. Given that the darkest simulant used in this study may be lighter than the darkest dust that could be encountered on the lunar surface, it becomes apparent that the performance degradation of thermal control surfaces due to dust on the Moon will be strongly dependent on the and of the dust in the specific locality

  10. A 1-D Analytical Model for the Thermally Induced Stresses in the Mould Surface During Die Casting

    DEFF Research Database (Denmark)

    Hattel, Jesper; Hansen, Preben

    1994-01-01

    This paper presents an anlytically based method for predicting the normal stresses in a die mold surface exposed to a thermal load. A example of application of the method is the high-pressure di casting process where the surface stresses in critical cases lead to cracks. Expressions for the normal...

  11. Evaluation of the surface urban heat island effect in the city of Madrid by thermal remote sensing

    NARCIS (Netherlands)

    Sobrino, J.; Oltra-Carrio, R; Jimenez-Munoz, J.C.; Franch, B.; Hidalgo, V.; Mattar, C.; Julien, Y.; Cuenca, J.; Romaguera, M.; Gomez, J.A.; Miguel, de E.; Bianchi, R.; Paganini, M.

    2013-01-01

    The surface urban heat island (SUHI) effect is defined as the increased surface temperatures in urban areas in contrast to cooler surrounding rural areas. In this article, the evaluation of the SUHI effect in the city of Madrid (Spain) from thermal infrared (TIR) remote-sensing data is presented. Th

  12. Surface enhanced Raman optical activity (SEROA)

    DEFF Research Database (Denmark)

    Abdali, Salim; Blanch, E.W.

    2008-01-01

    Raman optical activity (ROA) directly monitors the stereochemistry of chiral molecules and is now an incisive probe of biomolecular structure. ROA spectra contain a wealth of information on tertiary folding, secondary structure and even the orientation of individual residues in proteins and nucleic...

  13. Measuring temperature-dependent activation energy in thermally activated processes: a 2D Arrhenius plot method.

    Science.gov (United States)

    Li, Jian V; Johnston, Steven W; Yan, Yanfa; Levi, Dean H

    2010-03-01

    Thermally activated processes are characterized by two key quantities, activation energy (E(a)) and pre-exponential factor (nu(0)), which may be temperature dependent. The accurate measurement of E(a), nu(0), and their temperature dependence is critical for understanding the thermal activation mechanisms of non-Arrhenius processes. However, the classic 1D Arrhenius plot-based methods cannot unambiguously measure E(a), nu(0), and their temperature dependence due to the mathematical impossibility of resolving two unknown 1D arrays from one 1D experimental data array. Here, we propose a 2D Arrhenius plot method to solve this fundamental problem. Our approach measures E(a) at any temperature from matching the first and second moments of the data calculated with respect to temperature and rate in the 2D temperature-rate plane, and therefore is able to unambiguously solve E(a), nu(0), and their temperature dependence. The case study of deep level emission in a Cu(In,Ga)Se(2) solar cell using the 2D Arrhenius plot method reveals clear temperature dependent behavior of E(a) and nu(0), which has not been observable by its 1D predecessors.

  14. Evaluation of Haney-Type Surface Thermal Boundary Conditions Using a Coupled Atmosphere and Ocean Model

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A coupled atmosphere-ocean model developed at the Institute for Space Studies at NASA Goddard Space Flight Center (Russell et al., 1995) was used to verify the validity of Haney-type surface thermal boundary condition, which linearly connects net downward surface heat flux Q to air / sea temperature difference △T by a relaxation coefficient k. The model was initiated from the National Centers for Environmental Prediction (NCEP) atmospheric observations for 1 December 1977, and from the National Ocean Data Center (NODC) global climatological mean December temperature and salinity fields at 1° ×1° resolution. The time step is 7.5 minutes. We integrated the model for 450 days and obtained a complete model-generated global data set of daily mean downward net surface flux Q, surface air temperature TA,and sea surface temperature To. Then, we calculated the cross-correlation coefficients (CCC) between Q and △T. The ensemble mean CCC fields show (a) no correlation between Q and △T in the equatorial regions, and (b) evident correlation (CCC≥ 0.7) between Q and △T in the middle and high latitudes.Additionally, we did the variance analysis and found that when k= 120 W m-2K-1, the two standard deviations, σrq and σk△T, are quite close in the middle and high latitudes. These results agree quite well with a previous research (Chu et al., 1998) on analyzing the NCEP re-analyzed surface data, except that a smaller value of k (80 W m-2K-1) was found in the previous study.

  15. Simulated sensitivity of the tropical climate to extratropical thermal forcing: tropical SSTs and African land surface

    Science.gov (United States)

    Talento, Stefanie; Barreiro, Marcelo

    2016-08-01

    This study investigates the Intertropical Convergence Zone (ITCZ) response to extratropical thermal forcing applied to an atmospheric general circulation model coupled to slab ocean and land models. We focus on the relative roles of the atmosphere, tropical sea surface temperatures (SSTs) and continental surface temperatures in the ITCZ response to the imposed forcing. The forcing consists of cooling in one hemisphere and warming in the other poleward of 40°, with zero global average. Three sets of experiments are performed: in the first the slab ocean and land models are applied globally; in the second the tropical SSTs are kept fixed while the slab land model is applied globally; in the third, in addition, surface temperatures over Africa are kept fixed. Realistic boundary surface conditions are used. We find that the ITCZ shifts towards the warmer hemisphere and that the stronger the forcing, the larger the shift. When the constraint of fixed tropical SST is imposed we find that the ITCZ response is strongly weakened, but it is still not negligible in particular over the Atlantic Ocean and Africa where the precipitation anomalies are of the order of 20 and 60 %, respectively, of the magnitude obtained without the SST restriction. Finally, when the constraint of the African surface temperature is incorporated we find that the ITCZ response completely vanishes, indicating that the ITCZ response to the extratropical forcing is not possible just trough purely atmospheric processes, but needs the involvement of either the tropical SST or the continental surface temperatures. The clear-sky longwave radiation feedback is highlighted as the main physical mechanism operating behind the land-based extratropical to tropical communication.

  16. Verification of a thermal simulation tool for moving objects on the lunar surface

    Science.gov (United States)

    Hager, Philipp; Reiss, Philipp

    2013-04-01

    The thermal environment of the Moon is a challenge for the design and successful operation of rovers and scientific instruments, especially for dynamic, mobile situations. Examples range from transport and stability of volatile samples in transport devices at the lunar poles to an analysis instrument, to astronauts exploring varied terrain. A dynamic thermal simulation tool for moving objects on the lunar surface was created and its verification for several test cases against Lunar Reconnaissance Orbiter DIVINER brightness temperature data is presented here. The Thermal Moon Simulator (TherMoS) allows the prediction of incoming heat fluxes on a mobile object on the lunar surface and subsequent object temperatures. A model for regolith temperatures based on the models presented in [1,2] was set in a MATLAB simulation context. A time-marching numerical finite-difference approach was used to calculate the temperatures for log-distributed regolith depth nodes to a depth of 2m. The lunar interior heat flux was set to 0.033 [W ? m-2], based on the early publications of [3]. The incoming heat fluxes are calculated with a ray tracing algorithm. Parallel solar rays and their diffuse reflected components lead to the solar heat flux for each surface element. Additionally each surface element emits hemispherical, diffuse infrared rays that are absorbed by the object as well as other lunar surface elements. The lunar topography is represented in a triangular mesh. The topography is either derived from Kaguya LALT data or generated artificially. In the latter case craters and boulders are placed manually or randomly in a level terrain. This approach is restricted to bowl shaped primary craters with a boulder size and spatial distribution that takes into account the region (mare or highland) and the parent crater diameter [4,5,6]. A thermal boulder model is integrated, based on work performed by [7]. This model also uses a finite-difference numerical approach to compute boulder

  17. A Useful Tool for Atmospheric Correction and Surface Temperature Estimation of Landsat Infrared Thermal Data

    Science.gov (United States)

    Rivalland, Vincent; Tardy, Benjamin; Huc, Mireille; Hagolle, Olivier; Marcq, Sébastien; Boulet, Gilles

    2016-04-01

    Land Surface temperature (LST) is a critical variable for studying the energy and water budgets at the Earth surface, and is a key component of many aspects of climate research and services. The Landsat program jointly carried out by NASA and USGS has been providing thermal infrared data for 40 years, but no associated LST product has been yet routinely proposed to community. To derive LST values, radiances measured at sensor-level need to be corrected for the atmospheric absorption, the atmospheric emission and the surface emissivity effect. Until now, existing LST products have been generated with multi channel methods such as the Temperature/Emissivity Separation (TES) adapted to ASTER data or the generalized split-window algorithm adapted to MODIS multispectral data. Those approaches are ill-adapted to the Landsat mono-window data specificity. The atmospheric correction methodology usually used for Landsat data requires detailed information about the state of the atmosphere. This information may be obtained from radio-sounding or model atmospheric reanalysis and is supplied to a radiative transfer model in order to estimate atmospheric parameters for a given coordinate. In this work, we present a new automatic tool dedicated to Landsat thermal data correction which improves the common atmospheric correction methodology by introducing the spatial dimension in the process. The python tool developed during this study, named LANDARTs for LANDsat Automatic Retrieval of surface Temperature, is fully automatic and provides atmospheric corrections for a whole Landsat tile. Vertical atmospheric conditions are downloaded from the ERA Interim dataset from ECMWF meteorological organization which provides them at 0.125 degrees resolution, at a global scale and with a 6-hour-time step. The atmospheric correction parameters are estimated on the atmospheric grid using the commercial software MODTRAN, then interpolated to 30m resolution. We detail the processing steps

  18. Influence of deposition temperature of thermal ALD deposited Al2O3 films on silicon surface passivation

    Science.gov (United States)

    Batra, Neha; Gope, Jhuma; Vandana, Panigrahi, Jagannath; Singh, Rajbir; Singh, P. K.

    2015-06-01

    The effect of deposition temperature (Tdep) and subsequent annealing time (tanl) of atomic layer deposited aluminum oxide (Al2O3) films on silicon surface passivation (in terms of surface recombination velocity, SRV) is investigated. The pristine samples (as-deposited) show presence of positive fixed charges, QF. The interface defect density (Dit) decreases with increase in Tdep which further decreases with tanl up to 100s. An effective surface passivation (SRV<8 cm/s) is realized for Tdep ≥ 200 °C. The present investigation suggests that low thermal budget processing provides the same quality of passivation as realized by high thermal budget process (tanl between 10 to 30 min).

  19. Utilizing avidity to improve antifreeze protein activity: a type III antifreeze protein trimer exhibits increased thermal hysteresis activity.

    Science.gov (United States)

    Can, Özge; Holland, Nolan B

    2013-12-03

    Antifreeze proteins (AFPs) are ice growth inhibitors that allow the survival of several species living at temperatures colder than the freezing point of their bodily fluids. AFP activity is commonly defined in terms of thermal hysteresis, which is the difference observed for the solution freezing and melting temperatures. Increasing the thermal hysteresis activity of these proteins, particularly at low concentrations, is of great interest because of their wide range of potential applications. In this study, we have designed and expressed one-, two-, and three-domain antifreeze proteins to improve thermal hysteresis activity through increased binding avidity. The three-domain type III AFP yielded significantly greater activity than the one- and two-domain proteins, reaching a thermal hysteresis of >1.6 °C at a concentration of hysteresis activity.

  20. A Software Tool for Atmospheric Correction and Surface Temperature Estimation of Landsat Infrared Thermal Data

    Directory of Open Access Journals (Sweden)

    Benjamin Tardy

    2016-08-01

    Full Text Available Land surface temperature (LST is an important variable involved in the Earth’s surface energy and water budgets and a key component in many aspects of environmental research. The Landsat program, jointly carried out by NASA and the USGS, has been recording thermal infrared data for the past 40 years. Nevertheless, LST data products for Landsat remain unavailable. The atmospheric correction (AC method commonly used for mono-window Landsat thermal data requires detailed information concerning the vertical structure (temperature, pressure and the composition (water vapor, ozone of the atmosphere. For a given coordinate, this information is generally obtained through either radio-sounding or atmospheric model simulations and is passed to the radiative transfer model (RTM to estimate the local atmospheric correction parameters. Although this approach yields accurate LST data, results are relevant only near this given coordinate. To meet the scientific community’s demand for high-resolution LST maps, we developed a new software tool dedicated to processing Landsat thermal data. The proposed tool improves on the commonly-used AC algorithm by incorporating spatial variations occurring in the Earth’s atmosphere composition. The ERA-Interim dataset (ECMWFmeteorological organization was used to retrieve vertical atmospheric conditions, which are available at a global scale with a resolution of 0.125 degrees and a temporal resolution of 6 h. A temporal and spatial linear interpolation of meteorological variables was performed to match the acquisition dates and coordinates of the Landsat images. The atmospheric correction parameters were then estimated on the basis of this reconstructed atmospheric grid using the commercial RTMsoftware MODTRAN. The needed surface emissivity was derived from the common vegetation index NDVI, obtained from the red and near-infrared (NIR bands of the same Landsat image. This permitted an estimation of LST for the entire

  1. A Near-Infrared and Thermal Imager for Mapping Titan's Surface Features

    Science.gov (United States)

    Aslam, S.; Hewagma, T.; Jennings, D. E.; Nixon, C.

    2012-01-01

    Approximately 10% of the solar insolation reaches the surface of Titan through atmospheric spectral windows. We will discuss a filter based imaging system for a future Titan orbiter that will exploit these windows mapping surface features, cloud regions, polar storms. In the near-infrared (NIR), two filters (1.28 micrometer and 1.6 micrometer), strategically positioned between CH1 absorption bands, and InSb linear array pixels will explore the solar reflected radiation. We propose to map the mid, infrared (MIR) region with two filters: 9.76 micrometer and 5.88-to-6.06 micrometers with MCT linear arrays. The first will map MIR thermal emission variations due to surface albedo differences in the atmospheric window between gas phase CH3D and C2H4 opacity sources. The latter spans the crossover spectral region where observed radiation transitions from being dominated by thermal emission to solar reflected light component. The passively cooled linear arrays will be incorporated into the focal plane of a light-weight thin film stretched membrane 10 cm telescope. A rad-hard ASIC together with an FPGA will be used for detector pixel readout and detector linear array selection depending on if the field-of-view (FOV) is looking at the day- or night-side of Titan. The instantaneous FOV corresponds to 3.1, 15.6, and 31.2 mrad for the 1, 5, and 10 micrometer channels, respectively. For a 1500 km orbit, a 5 micrometer channel pixel represents a spatial resolution of 91 m, with a FOV that spans 23 kilometers, and Titan is mapped in a push-broom manner as determined by the orbital path. The system mass and power requirements are estimated to be 6 kg and 5 W, respectively. The package is proposed for a polar orbiter with a lifetime matching two Saturn seasons.

  2. Near-field thermal radiative emission of materials demonstrating near infrared surface polariton resonance

    Science.gov (United States)

    Petersen, Spencer Justin

    Surface polariton mediated near-field radiative transfer exceeds the blackbody limit by orders of magnitude and is quasimonochromatic. Thermophotovoltaic (TPV) power generation consists of converting thermal radiation into useful electrical energy and exhibits a peak performance near the TPV cell bandgap, which is typically located within the near infrared bandwidth. Therefore, an ideal emission source for a nanoscale gap TPV device, in which the emitter and cell are separated by no more than one peak emitted wavelength, will sustain surface polariton resonance at or near the TPV cell bandgap in the near infrared. To date, few materials have been identified that satisfy this requirement. The first objective of this dissertation is to theoretically explore dielectric Mie resonance-based (DMRB) electromagnetic metamaterials for the potential to sustain near infrared surface polariton resonance. Electromagnetic metamaterials are composite media, consisting of subwavelength, repeating unit structures called "meta-atoms." The microscopic configuration of the meta-atom can be engineered, dictating the effective macroscale electromagnetic properties of the bulk metamaterial, including the surface polariton resonance wavelength. DMRB metamaterials consist of dielectric nanoparticles within a host medium and are analyzed using an effective medium theory. The local density of electromagnetic states, an indicator of possibly harvestable energy near an emitting surface, is calculated for two DMRB metamaterials: spherical nanoparticles of 1) silicon carbide, and 2) silicon embedded in a host medium. Results show that the surface polariton resonance of these metamaterials is tunable and, for the silicon metamaterial only, is found in the near infrared bandwidth, making it a viable candidate for use in a nano-TPV device. In order to demonstrate the practicality thereof, the second objective is to fabricate and characterize DMRB metamaterials. Specimens are fabricated by hand

  3. A study of thermally activated Mg–Fe layered double hydroxides as potential environmental catalysts

    Directory of Open Access Journals (Sweden)

    MILICA S. HADNAĐEV-KOSTIĆ

    2010-09-01

    Full Text Available Layered double hydroxides (LDHs and mixed oxides derived after thermal decomposition of LDHs with different Mg–Fe contents were investigated. These materials were chosen because of the possibility to tailor their various properties, such as ion-exchange capability, redox and acid–base and surface area. Layered double hydroxides, [Mg1-xFex(OH2](CO3x/2×mH2O (where x presents the content of trivalent ions, x = M(III/(M(II + M(III were synthesized using the low supersaturation precipitation method. The influence of different Mg/Fe ratios on the structure and surface properties of the LDH and derived mixed oxides was investigated in correlation to their catalytic properties in the chosen test reaction (Fischer–Tropsch synthesis. It was determined that the presence of active sites in the mixed oxides is influenced by the structural properties of the initial LDH and by the presence of additional Fe phases. Furthermore, a synthesis outside the optimal range for the synthesis of single phase LDHs leads to the formation of metastable, multiphase systems with specific characteristics and active sites.

  4. Influence of surface morphology and microstructure on performance of CVD tungsten coating under fusion transient thermal loads

    Science.gov (United States)

    Lian, Youyun; Liu, Xiang; Wang, Jianbao; Feng, Fan; Lv, Yanwei; Song, Jiupeng; Chen, Jiming

    2016-12-01

    Thick tungsten coatings have been deposited by chemical vapor deposition (CVD) at a rapid growth rate. A series of tungsten coatings with different thickness and surface morphology were prepared. The surface morphology, microstructure and preferred orientation of the CVD tungsten coatings were investigated. Thermal shock analyses were performed by using an electron beam facility to study the influence of the surface morphology and the microstructure on the thermal shock resistance of the CVD tungsten coatings. Repetitive (100 pulses) ELMs-like thermal shock loads were applied at various temperatures between room temperature and 600 °C with pulse duration of 1 ms and an absorbed power density of up to 1 GW/m2. The results of the tests demonstrated that the specific surface morphology and columnar crystal structure of the CVD tungsten have significant influence on the surface cracking threshold and crack propagation of the materials. The CVD tungsten coatings with a polished surface show superior thermal shock resistance as compared with that of the as-deposited coatings with a rough surface.

  5. Laser thermal annealing of Ge, optimized for highly activated dopants and diode ION/IOFF ratios

    DEFF Research Database (Denmark)

    Shayesteh, M.; O'Connell, D.; Gity, F.;

    2014-01-01

    The authors compared the influence of laser thermal annealing (LTA) and rapid thermal annealing (RTA) on dopant activation and electrical performance of phosphorus and arsenic doped n+/p junction. High carrier concentration above 1020 cm-3 as well as an ION/IOFF ratio of approximately 105 and ide...

  6. Nonadiabatic spin torque investigated using thermally activated magnetic domain wall dynamics

    NARCIS (Netherlands)

    Eltschka, M.; Wötzel, M.; Rhensius, J.; Krzyk, S.; Nowak, U.; Kläui, M.; Kasama, T.; Dunin-Borkowski, R. E.; Heyderman, L. J.; van Driel, H.J.; Duine, R.A.

    2010-01-01

    Using transmission electron microscopy, we investigate the thermally activated motion of domain walls (DWs) between two positions in Permalloy (Ni80Fe20) nanowires at room temperature. We show that this purely thermal motion is well described by an Arrhenius law, allowing for a description of the DW

  7. Nonadiabatic Spin Torque Investigated Using Thermally Activated Magnetic Domain Wall Dynamics

    DEFF Research Database (Denmark)

    Eltschka, M.; Woetzel, Mathias; Rhensius, J.

    2010-01-01

    Using transmission electron microscopy, we investigate the thermally activated motion of domain walls (DWs) between two positions in Permalloy (Ni80Fe20) nanowires at room temperature. We show that this purely thermal motion is well described by an Arrhenius law, allowing for a description...

  8. On the early and developed stages of surface condensation: competition mechanism between interfacial and condensate bulk thermal resistances

    Science.gov (United States)

    Sun, Jie; Wang, Hua Sheng

    2016-10-01

    We use molecular dynamics simulation to investigate the early and developed stages of surface condensation. We find that the liquid-vapor and solid-liquid interfacial thermal resistances depend on the properties of solid and fluid, which are time-independent, while the condensate bulk thermal resistance depends on the condensate thickness, which is time-dependent. There exists intrinsic competition between the interfacial and condensate bulk thermal resistances in timeline and the resultant total thermal resistance determines the condensation intensity for a given vapor-solid temperature difference. We reveal the competition mechanism that the interfacial thermal resistance dominates at the onset of condensation and holds afterwards while the condensate bulk thermal resistance gradually takes over with condensate thickness growing. The weaker the solid-liquid bonding, the later the takeover occurs. This competition mechanism suggests that only when the condensate bulk thermal resistance is reduced after it takes over the domination can the condensation be effectively intensified. We propose a unified theoretical model for the thermal resistance analysis by making dropwise condensation equivalent to filmwise condensation. We further find that near a critical point (contact angle being ca. 153°) the bulk thermal resistance has the least opportunity to take over the domination while away from it the probability increases.

  9. Influence of Different Surface Treatments of H13 Hot Work Die Steel on Its Thermal Fatigue Behaviors

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Thermal fatigue checking is the general failure of hot work die steels, which is relative with the structures and properties of the steels and the stress alternated during the employment. The Uddeholm test method on thermal fatigue is used to compare the behaviors of different samples, which are treated with plasma nitriding、plasma sulfur-carbon-nitriding、 boronizing or not treated. The results show that the nitriding improves the thermal fatigue property of the tool steel, while the plasma sulfur-carbon-nitriding and the boronizing impair the property. The mechanisms are induced as follows. By increasing the hardness and changing the stress distribution in the surface layer, surface treatment can decrease the plastic deformation and the tensile stress during the cycling. Therefore,the generation and growth of the cracks are restrained. On the other hand, as results of surface treating, in the surface layer the toughness declines and the expanding coefficient ascendes; the latter change caused the strengthening of the tensile and compressive stress during the cycling. Thus the resistance to thermal fatigue is weakened. Whether or not the surface treatment is favor to thermal fatigue of tool steels relies on which factor is dominant.

  10. Enhanced active aluminum content and thermal behaviour of nano-aluminum particles passivated during synthesis using thermal plasma route

    Science.gov (United States)

    Mathe, Vikas L.; Varma, Vijay; Raut, Suyog; Nandi, Amiya Kumar; Pant, Arti; Prasanth, Hima; Pandey, R. K.; Bhoraskar, Sudha V.; Das, Asoka K.

    2016-04-01

    Here, we report synthesis and in situ passivation of aluminum nanoparticles using thermal plasma reactor. Both air and palmitc acid passivation was carried out during the synthesis in the thermal plasma reactor. The passivated nanoparticles have been characterized for their structural and morphological properties using X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques. In order to understand nature of passivation vibrational spectroscopic analysis have been carried out. The enhancement in active aluminum content and shelf life for a palmitic acid passivated nano-aluminum particles in comparison to the air passivated samples and commercially available nano Al powder (ALEX) has been observed. Thermo-gravimetric analysis was used to estimate active aluminum content of all the samples under investigation. In addition cerimetric back titration method was also used to estimate AAC and the shelf life of passivated aluminum particles. Structural, microstructural and thermogravomateric analysis of four year aged passivated sample also depicts effectiveness of palmitic acid passivation.

  11. Construction of Renewable Superhydrophobic Surfaces via Thermally Induced Phase Separation and Mechanical Peeling

    Institute of Scientific and Technical Information of China (English)

    Qi Zhu; Yuan Yu; Qing-Yun Wu; Lin Gu

    2017-01-01

    We report a simple preparation method of a renewable superhydrophobic surface by thermally induced phase separation (TIPS) and mechanical peeling.Porous polyvinylidene fluoride (PVDF) membranes with hierarchical structures were prepared by a TIPS process under different cooling conditions,which were confirmed by scanning electron microscopy and mercury intrusion porosimetry.After peeling off the top layer,rough structures with hundreds of nanometers to several microns were obtained.A digital microscopy determines that the surface roughness of peeled PVDF membranes is much higher than that of the original PVDF membrane,which is important to obtain the superhydrophobicity.Water contact angle and sliding angle measurements demonstrate that the peeled membrane surfaces display superhydrophobicity with a high contact angle (152°) and a low sliding angle (7.2°).Moreover,the superhydrophobicity can be easily recovered for many times by a simple mechanical peeling,identical to the original superhydrophobicity.This simple preparation method is low cost,and suitable for large-scale industrialization,which may offer more opportunities for practical applications.

  12. Surface Pre-treatment for Thermally Sprayed ZnAl15 Coatings

    Science.gov (United States)

    Bobzin, K.; Öte, M.; Knoch, M. A.

    2017-02-01

    Pre-treatment of substrates is an important step in thermal spraying. It is widely accepted that mechanical interlocking is the dominant adhesion mechanism for most substrate-coating combinations. To prevent premature failure, minimum coating adhesion strength, surface preparation grades, and roughness parameters are often specified. For corrosion-protection coatings for offshore wind turbines, an adhesion strength ≥ 5 MPa is commonly assumed to ensure adhesion over service lifetime. In order to fulfill this requirement, Rz > 80 µm and a preparation grade of Sa3 are common specifications. In this study, the necessity of these requirements is investigated using the widely used combination of twin-wire arc-sprayed ZnAl15 on S355J2 + N as a test case. By using different blasting media and parameters, the correlation between coating adhesion and roughness parameters is analyzed. The adhesion strength of these systems is measured using a test method allowing measurements on real parts. The results are compared to DIN EN 582:1993, the European equivalent of ASTM-C633. In another series of experiments, the influence of surface pre-treatment grades Sa2.5 and Sa3 is considered. By combining the results of these three sets of experiments, a guideline for surface pre-treatment and adhesion testing on real parts is proposed for the considered system.

  13. Surface thermal analysis of North Brabant cities and neighbourhoods during heat waves

    Directory of Open Access Journals (Sweden)

    Leyre Echevarria Icaza

    2016-03-01

    Full Text Available The urban heat island effect is often associated with large metropolises. However, in the Netherlands even small cities will be affected by the phenomenon in the future (Hove et al., 2011, due to the dispersed or mosaic urbanisation patterns in particularly the southern part of the country: the province of North Brabant. This study analyses the average night time land surface temperature (LST of 21 North-Brabant urban areas through 22 satellite images retrieved by Modis 11A1 during the 2006 heat wave and uses Landsat 5 Thematic Mapper to map albedo and normalized difference temperature index (NDVI values. Albedo, NDVI and imperviousness are found to play the most relevant role in the increase of night-time LST. The surface cover cluster analysis of these three parameters reveals that the 12 “urban living environment” categories used in the region of North Brabant can actually be reduced to 7 categories, which simplifies the design guidelines to improve the surface thermal behaviour of the different neighbourhoods thus reducing the Urban Heat Island (UHI effect in existing medium size cities and future developments adjacent to those cities.

  14. Hydrophilic modification of polyethersulfone porous membranes via a thermal-induced surface crosslinking approach

    Science.gov (United States)

    Mu, Li-Jun; Zhao, Wen-Zhen

    2009-05-01

    A thermal-induced surface crosslinking process was employed to perform a hydrophilic surface modification of PES porous membranes. Difunctional poly(ethylene glycol) diacrylate (PEGDA) was used as the main crosslinking modifier. The addition of trifunctional trimethylolpropane trimethylacrylate (TMPTMA) into the reaction solutions accelerated the crosslinking progress of PEGDA on PES membranes. The membrane surface morphology and chemical composition were characterized by scanning electron microscopy (SEM) and FTIR-ATR spectroscopy. The mass gains (MG) of the modified membranes could be conveniently modulated by varying the PEGDA concentration and crosslinking time. The measurements of water contact angle showed that the hydrophilicity of PES membranes was remarkably enhanced by the coating of crosslinked PEGDA layer. When a moderate mass gain of about 150 μg/cm 2 was reached, both the permeability and anti-fouling ability of PES membranes could be significantly improved. Excessive mass gain not only contributed little to the anti-fouling ability, but also brought a deteriorated permeability to PES membranes.

  15. EXPERIMENTAL EVALUATION OF THE THERMAL PERFORMANCE OF A WATER SHIELD FOR A SURFACE POWER REACTOR

    Energy Technology Data Exchange (ETDEWEB)

    REID, ROBERT S. [Los Alamos National Laboratory; PEARSON, J. BOSIE [Los Alamos National Laboratory; STEWART, ERIC T. [Los Alamos National Laboratory

    2007-01-16

    Water based reactor shielding is being investigated for use on initial lunar surface power systems. A water shield may lower overall cost (as compared to development cost for other materials) and simplify operations in the setup and handling. The thermal hydraulic performance of the shield is of significant interest. The mechanism for transferring heat through the shield is natural convection. Natural convection in a 100 kWt lunar surface reactor shield design is evaluated with 2 kW power input to the water in the Water Shield Testbed (WST) at the NASA Marshall Space Flight Center. The experimental data from the WST is used to validate a CFD model. Performance of the water shield on the lunar surface is then predicted with a CFD model anchored to test data. The experiment had a maximum water temperature of 75 C. The CFD model with 1/6-g predicts a maximum water temperature of 88 C with the same heat load and external boundary conditions. This difference in maximum temperature does not greatly affect the structural design of the shield, and demonstrates that it may be possible to use water for a lunar reactor shield.

  16. Experimental Evaluation of the Thermal Performance of a Water Shield for a Surface Power Reactor

    Science.gov (United States)

    Pearson, J. Boise; Stewart, Eric T.; Reid, Robert S.

    2007-01-01

    A water based shielding system is being investigated for use on initial lunar surface power systems. The use of water may lower overall cost (as compared to development cost for other materials) and simplify operations in the setup and handling. The thermal hydraulic performance of the shield is of significant interest. The mechanism for transferring heat through the shield is natural convection. Natural convection in a representative lunar surface reactor shield design is evaluated at various power levels in the Water Shield Testbed (WST) at the NASA Marshall Space Flight Center. The experimental data from the WST is used to anchor a CFD model. Performance of a water shield on the lunar surface is then predicted by CFD models anchored to test data. The accompanying viewgraph presentation includes the following topics: 1) Testbed Configuration; 2) Core Heater Placement and Instrumentation; 3) Thermocouple Placement; 4) Core Thermocouple Placement; 5) Outer Tank Thermocouple Placement; 6) Integrated Testbed; 7) Methodology; 8) Experimental Results: Core Temperatures; 9) Experimental Results; Outer Tank Temperatures; 10) CFD Modeling; 11) CFD Model: Anchored to Experimental Results (1-g); 12) CFD MOdel: Prediction for 1/6-g; and 13) CFD Model: Comparison of 1-g to 1/6-g.

  17. Surface laser-glazing of plasma-sprayed thermal barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Batista, C. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Portinha, A. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Ribeiro, R.M. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal)]. E-mail: ricardo@fisica.uminho.pt; Teixeira, V. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Costa, M.F. [University of Minho, Physics Department, Campus de Gualtar, 4710-057 Braga (Portugal); Oliveira, C.R. [Instituto de Desenvolvimentoe Inovacao Tecnologica (IDIT), 4520-102 Santa Maria da Feira (Portugal); University Lusiada, 4760-108 Vila Nova de Famalicao (Portugal)

    2005-07-15

    Atmospheric plasma-sprayed (APS) ZrO{sub 2}-8%WtY{sub 2}O{sub 3} thermal barrier coatings (TBCs) were subjected to a CO{sub 2} continuous wave laser-glazing process in order to generate an external dense layer produced by different processing parameters. For that purpose, different beam scanning speeds and track overlapping were chosen. Surface roughness has been reduced significantly after laser-glazing. Despite the surface crack network, all laser-glazed specimens presented a fully dense and porous free external layer with a columnar microstructure. Surface cracks along the densified layer were found to have tendency to be oriented in two perpendicular directions, one in the direction of the laser beam travel, the other perpendicular to it. Moreover, the cracks parallel to the beam moving direction are found to be on the overlapping zone, coinciding with the edge of the subsequent track. The cracks along the densified layer are vertical and tend to branch and deviate from the vertical direction within the porous PS coating. The largest overlapping allied to the smallest amount of irradiated energy generated the most uniform layer with the shortest crack branches within the PS coating. For the as-sprayed coating, the XRD results revealed mainly t' non-transformable tetragonal zirconia with a small percentage of residual monoclinic zirconia. All glazed coatings presented only t' non-transformable tetragonal zirconia with some variations on preferable crystal orientation.

  18. Parylene-based active micro space radiator with thermal contact switch

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, Ai; Suzuki, Yuji [Department of Mechanical Engineering, The University of Tokyo, Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan)

    2014-03-03

    Thermal management is crucial for highly functional spacecrafts exposed to large fluctuations of internal heat dissipation and/or thermal boundary conditions. Since thermal radiation is the only means for heat removal, effective control of radiation is required for advanced space missions. In the present study, a MEMS (Micro Electro Mechanical Systems) active radiator using the contact resistance change has been proposed. Unlike previous bulky thermal louvers/shutters, higher fill factor can be accomplished with an array of electrostatically driven micro diaphragms suspended with polymer tethers. With an early prototype developed with parylene MEMS technologies, radiation heat flux enhancement up to 42% has been achieved.

  19. A REVIEW OF OXYGEN-CONTAINING SURFACE GROUPS AND SURFACE MODIFICATION OF ACTIVATED CARBON

    Institute of Scientific and Technical Information of China (English)

    WU Yongwen; LI Zhong; XI Hongxia; XIA Qibin

    2004-01-01

    This review focused on the recent reports related to the function, characterization and modification of oxygen-containing surface groups of activated carbon (AC). The Oxygen-containing surface groups were briefly described, and the most frequently used techniques for characterization of the oxygen-containing surface groups on ACs were also briefly stated. A detailed discussion of the effects of the oxygen-containing surface groups on the adsorptive capacity of AC was given. The recent progresses in modification of the oxygen-containing surface groups of AC were also reviewed.

  20. Impact of various surface covers on water and thermal regime of Technosol

    Science.gov (United States)

    Kodešová, Radka; Fér, Miroslav; Klement, Aleš; Nikodem, Antonín; Teplá, Daniela; Neuberger, Pavel; Bureš, Petr

    2014-11-01

    Different soil covers influence water and thermal regimes in soils within urban areas. Knowledge of these regimes is needed, particularly when assessing effectiveness of energy gathering from soils using horizontal ground heat exchangers. The goal of this study was to calibrate the model HYDRUS-1D for simulating coupled water and thermal regime in Technosol type soils with grass cover, and to use this model for predicting water and thermal regimes under different materials covering the soil surface. For this purpose soil water contents were measured at depths of 10, 20, 30, 40, 60 and 100 cm at 4 locations and temperatures were measured at depths of 20, 40, 80, 120, 150 and 180 cm at three locations (all covered by grass) from June 2011 to December 2012. In addition sensors for simultaneous measuring soil water contents and temperatures were installed under different soil covers (grass, bark chips, sand, basalt gravel and concrete paving) at a depth of 7. The parameters of soil hydraulic properties were obtained on the 100-cm3 undisturbed soil samples using the multi-step outflow experiment and numerical inversion of the measured transient flow data using HYDRUS-1D. HYDRUS-1D was then used to simulated the water regime within the soil profile under the grass cover using climatic data from June 2011 to December 2012 and some of the soil hydraulic parameters were additionally numerically optimized using soil water contents measured at all depths. Water flow and heat transport were then simulated using these parameters, measured thermal properties and temperatures measured close to the surface applied as a top boundary condition. Simulated temperatures at all depths successfully approximated the measured data. Next, water and thermal regimes under another 4 different surface covers were simulated. Soil hydraulic properties of different materials were partly measured and partly optimized when simulating soil water regime from June 2011 to December 2012 using the soil

  1. Biomimetic Bacterial Identification Platform Based on Thermal Wave Transport Analysis (TWTA) through Surface-Imprinted Polymers.

    Science.gov (United States)

    Steen Redeker, Erik; Eersels, Kasper; Akkermans, Onno; Royakkers, Jeroen; Dyson, Simba; Nurekeyeva, Kunya; Ferrando, Beniamino; Cornelis, Peter; Peeters, Marloes; Wagner, Patrick; Diliën, Hanne; van Grinsven, Bart; Cleij, Thomas Jan

    2017-05-12

    This paper introduces a novel bacterial identification assay based on thermal wave analysis through surface-imprinted polymers (SIPs). Aluminum chips are coated with SIPs, serving as synthetic cell receptors that have been combined previously with the heat-transfer method (HTM) for the selective detection of bacteria. In this work, the concept of bacterial identification is extended toward the detection of nine different bacterial species. In addition, a novel sensing approach, thermal wave transport analysis (TWTA), is introduced, which analyzes the propagation of a thermal wave through a functional interface. The results presented here demonstrate that bacterial rebinding to the SIP layer resulted in a measurable phase shift in the propagated wave, which is most pronounced at a frequency of 0.03 Hz. In this way, the sensor is able to selectively distinguish between the different bacterial species used in this study. Furthermore, a dose-response curve was constructed to determine a limit of detection of 1 × 10(4) CFU mL(-1), indicating that TWTA is advantageous over HTM in terms of sensitivity and response time. Additionally, the limit of selectivity of the sensor was tested in a mixed bacterial solution, containing the target species in the presence of a 99-fold excess of competitor species. Finally, a first application for the sensor in terms of infection diagnosis is presented, revealing that the platform is able to detect bacteria in clinically relevant concentrations as low as 3 × 10(4) CFU mL(-1) in spiked urine samples.

  2. Enhanced diffusion due to active swimmers at a solid surface

    CERN Document Server

    Miño, Gaston; Darnige, Thierry; Hoyos, Mauricio; Dauchet, Jeremy; Dunstan, Jocelyn; Soto, Rodrigo; Wang, Yang; Rousselet, Annie; Clement, Eric

    2010-01-01

    We consider two systems of active swimmers moving close to a solid surface, one being a living population of wild-type \\textit{E. coli} and the other being an assembly of self-propelled Au-Pt rods. In both situations, we have identified two different types of motion at the surface and evaluated the fraction of the population that displayed ballistic trajectories (active swimmers) with respect to those showing random-like behavior. We studied the effect of this complex swimming activity on the diffusivity of passive tracers also present at the surface. We found that the tracer diffusivity is enhanced with respect to standard Brownian motion and increases linearly with the activity of the fluid, defined as the product of the fraction of active swimmers and their mean velocity. This result can be understood in terms of series of elementary encounters between the active swimmers and the tracers.

  3. Structural Characterization of Sputtered Silicon Thin Films after Rapid Thermal Annealing for Active-Matrix Organic Light Emitting Diode

    Science.gov (United States)

    Mugiraneza, Jean de Dieu; Miyahira, Tomoyuki; Sakamoto, Akinori; Chen, Yi; Okada, Tatsuya; Noguchi, Takashi; Itoh, Taketsugu

    2010-12-01

    The microcrystalline phase obtained by adopting a two-step rapid thermal annealing (RTA) process for rf-sputtered silicon films deposited on thermally durable glass was characterized. The optical properties, surface morphology, and internal stress of the annealed Si films are investigated. As the thermally durable glass substrate allows heating of the deposited films at high temperatures, micro-polycrystalline silicon (micro-poly-Si) films of uniform grain size with a smooth surface and a low internal stress could be obtained after annealing at 750 °C. The thermal stress in the Si films was 100 times lower than that found in the films deposited on conventional glass. Uniform grains with an average grain size of 30 nm were observed by transmission electron microscopy (TEM) in the films annealed at 800 °C. These micro-poly-Si films have potential application for fabrication of uniform and reliable thin film transistors (TFTs) for large scale active-matrix organic light emitting diode (AMOLED) displays.

  4. Thermal Fatigue Behaviour of Co-Based Alloy Coating Obtained by Laser Surface Melt-Casting on High Temperature Alloy

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A thermal fatigue behaviour of C o-based alloy coating obtained by laser surface melt-casting on the high tempe rature alloy GH33 was studied. The results show that after each time of thermal cycling, the final residual stress was formed in the melt-casting layer which is attributed to the thermal stress and structural stress. Through the first 50 times of thermal cycling, the morphology of coating still inherits the laser casting one, but the dendrites get bigger; After the second 50 times of thermal cycling, corrosion pits emerge from coating, and mostly in the places where coating and substrate meet. The fatigue damage type of coating belongs to stress corrosi on.

  5. Layer resolved spectroscopy of potassium adsorbed on a Ru(001) surface: Photoemission and thermal desorption study

    Energy Technology Data Exchange (ETDEWEB)

    Hrbek, J. (Chemistry Department, Brookhaven National Laboratory, Upton, New York 11973 (US)); Shek, M. (Department of Physics, Hunter College of CUNY, New York, New York 10021); Sham, T.K. (Department of Chemistry, University of Western Ontario, London, Ontario N6A 5B7, Canada); Xu, G. (Chemistry Department, Brookhaven National Laboratory, Upton, New York, 11973)

    1989-11-01

    High-resolution photoemission spectroscopy and thermal desorption were used to study the coverage dependence of the K 3{ital p}{sub 3/2,1/2} core levels of K overlayers on Ru(001). Three doublets were observed to evolve sequentially and to shift to higher binding energy with increasing coverage of potassium. The doublets were assigned to photoemission from the interface (first layer), bulk'' (second layer), and surface (third layer). Spin--orbit splitting was observed for the first time in the condensed potassium phase by photoemission. The results are discussed in terms of the equivalent core approximation using a Born--Haber cycle. In the thermal desorption data three coverage regimes can be distinguished: a first layer desorbing with first-order kinetics and a strongly decreasing heat of adsorption ({ital E}{sub {ital A}} =2.80--0.87 eV); a second layer with zero-order desorption kinetics and {ital E}{sub {ital A}} =0.78 eV; a third layer and multilayers with the same kinetic order but with {ital E}{sub {ital A}} increasing from 0.78 to 0.93 eV, which is close to the heat of sublimation of potassium.

  6. Thermal-hydraulics and safety analysis of sectored compact reactor for lunar surface power

    Energy Technology Data Exchange (ETDEWEB)

    Schriener, T. M. [Inst. for Space and Nuclear Power Studies, Univ. of New Mexico, Albuquerque, NM (United States); Chemical and Nuclear Engineering Dept., Univ. of New Mexico, Albuquerque, NM (United States); El-Genk, M. S. [Inst. for Space and Nuclear Power Studies, Univ. of New Mexico, Albuquerque, NM (United States); Chemical and Nuclear Engineering Dept., Univ. of New Mexico, Albuquerque, NM (United States); Mechanical Engineering Dept., Univ. of New Mexico, Albuquerque, NM (United States)

    2012-07-01

    The liquid NaK-cooled, fast-neutron spectrum, Sectored Compact Reactor (SCoRe-N 5) concept has been developed at the Univ. of New Mexico for lunar surface power applications. It is loaded with highly enriched UN fuel pins in a triangular lattice, and nominally operates at exit and inlet coolant temperatures of 850 K and 900 K. This long-life reactor generates up to 1 MWth continuously for {>=} 20 years. To avoid a single point failure in reactor cooling, the core is divided into 6 sectors that are neutronically and thermally coupled, but hydraulically independent. This paper performs a 3-D the thermal-hydraulic analysis of SCoRe--N 5 at nominal operation temperatures and a power level of 1 MWth. In addition, the paper investigates the potential of continuing reactor operation at a lower power in the unlikely event that one sector in the core experiences a loss of coolant (LOC). Redesigning the core with a contiguous steel matrix enhances the cooling of the sector experiencing a LOC. Results show that with a core sector experiencing a LOC, SCORE-N 5 could continue operating safely at a reduced power of 166.6 kWth. (authors)

  7. Contribution of ground surface altitude difference to thermal anomaly detection using satellite images: Application to volcanic/geothermal complexes in the Andes of Central Chile

    Science.gov (United States)

    Gutiérrez, Francisco J.; Lemus, Martín; Parada, Miguel A.; Benavente, Oscar M.; Aguilera, Felipe A.

    2012-09-01

    Detection of thermal anomalies in volcanic-geothermal areas using remote sensing methodologies requires the subtraction of temperatures, not provided by geothermal manifestations (e.g. hot springs, fumaroles, active craters), from satellite image kinetic temperature, which is assumed to correspond to the ground surface temperature. Temperatures that have been subtracted in current models include those derived from the atmospheric transmittance, reflectance of the Earth's surface (albedo), topography effect, thermal inertia and geographic position effect. We propose a model that includes a new parameter (K) that accounts for the variation of temperature with ground surface altitude difference in areas where steep relief exists. The proposed model was developed and applied, using ASTER satellite images, in two Andean volcanic/geothermal complexes (Descabezado Grande-Cerro Azul Volcanic Complex and Planchón-Peteroa-Azufre Volcanic Complex) where field data of atmosphere and ground surface temperature as well as radiation for albedo calibration were obtained in 10 selected sites. The study area was divided into three zones (Northern, Central and Southern zones) where the thermal anomalies were obtained independently. K value calculated for night images of the three zones are better constrained and resulted to be very similar to the Environmental Lapse Rate (ELR) determined for a stable atmosphere (ELR > 7 °C/km). Using the proposed model, numerous thermal anomalies in areas of ≥ 90 m × 90 m were identified that were successfully cross-checked in the field. Night images provide more reliable information for thermal anomaly detection than day images because they record higher temperature contrast between geothermal areas and its surroundings and correspond to more stable atmospheric condition at the time of image acquisition.

  8. Pulsar Polar Cap Heating and Surface Thermal X-Ray Emission I. Curvature Radiation Pair Fronts

    CERN Document Server

    Harding, A K; Harding, Alice K.; Muslimov, Alexander G.

    2001-01-01

    We investigate the effect of pulsar polar cap (PC) heating produced by positrons returning from the upper pair formation front. Our calculations are based on a self-consistent treatment of the pair dynamics and the effect of electric field screening by the returning positrons. We calculate the resultant X-ray luminosities, and discuss the dependence of the PC heating efficiencies on pulsar parameters, such as characteristic spin-down age, spin period, and surface magnetic field strength. In this study we concentrate on the regime where the pairs are produced in a magnetic field by curvature photons emitted by accelerating electrons. Our theoretical results are not in conflict with the available observational X-ray data and suggest that the effect of PC heating should significantly contribute to the thermal X-ray fluxes from middle-aged and old pulsars. The implications for current and future X-ray observations of pulsars are briefly outlined.

  9. The effect of surface roughness on lattice thermal conductivity of silicon nanowires

    Science.gov (United States)

    Wang, Zan; Ni, Zhonghua; Zhao, Ruijie; Chen, Minhua; Bi, Kedong; Chen, Yunfei

    2011-07-01

    A theoretic model is presented to take into account the roughness effects on phonon transport in Si nanowires (NWs). Based on the roughness model, an indirect Monte Carlo (MC) simulation is carried out to predict the lattice thermal conductivities of the NWs with different surface qualities. Through fitting the experimental data with the MC predictions, the scattering strength on phonons from the boundary, umklapp phonon-phonon processes and impurities can be estimated. It is found that the scattering on phonons by the roughness cell boundaries in a rough nanowire can reduce the phonon mean free path to be smaller than the nanowire diameter, the Casimir limit of the phonon mean free path in a flat nanowire for phonons engaged in completely diffused boundary scattering processes.

  10. Possible high absorptance and low emittance selective surface for high temperature solar thermal collectors.

    Science.gov (United States)

    Zhang, Q C; Kelly, J C; Mills, D R

    1991-05-01

    Optical reflectivity measurements show that the reflectivity of Ge is dramatically reduced in the wavelength 0.3-1.4-microm range after high dose oxygen ion implantation. To explain such greatly reduced reflectivity, a model has been developed for the reflectivity of high dose oxygen implanted germanium. Our experimentally measured and calculated reflectivities show that, for a layered structure consisting of a Ge and GeO(2) mixture on Ge on GeO(2) on a Cu substrate, a low reflectivity of 0-10% in the solar spectrum is obtained, together with a high reflectivity approximately 100% in the 1.7-25-microm wavelength range. This is close to that of an ideal selective surface for solar energy thermal collectors operating at high temperatures from 300 to 500 degrees C.

  11. Human thermal sensation: frequency response to sinusoidal stimuli at the surface of the skin

    DEFF Research Database (Denmark)

    Ring, J.W.; de Dear, Richard; Melikov, Arsen Krikor

    1993-01-01

    The question of how the human organism perceives changing thermal stimuli has been recently studied and reported in experiments where these stimuli were either ramps and plateaux or simply step changes. Other experiments have been done in which the stimuli have been periodically varying airflows...... function. This function is then compared with the functional form found in two experiments where the stimuli were pulsating airflows of differing frequency. The PSI model seems to simulate well the form of the response of the human skin system to varying temperature changes of a whole range of frequencies....... A psychosensory intensity (PSI) model has been developed to relate experimentally derived sensation data to simulated cutaneous thermoreceptor responses to the temperature ramp-plateaux and step stimuli applied to the skin surface by thermodes. From the point of view of signal processing, a natural extension...

  12. Signals for a Transition from Surface to Bulk Emission in Thermal Multifragmentation

    CERN Document Server

    Beaulieu, L; Kwiatkowski, K K; De Souza, R T; Hsi, W C; Pienkowski, L; Back, B B; Bracken, D S; Breuer, H; Cornell, E A; Gimeno-Nogues, F; Ginger, D S; Gushue, S; Korteling, R G; Laforest, R; Martin, E; Morley, K B; Ramakrishnan, E; Remsberg, L P; Rowland, D; Ruangma, A; Viola, V E; Wang, G; Winchester, E M; Yennello, S J

    2000-01-01

    Excitation-energy-gated two-fragment correlation functions have been studied between 2 to 9A MeV of excitation energy for equilibrium-like sources formed in $\\pi^-$ and p + $^{197}$Au reactions at beam momenta of 8,9.2 and 10.2 GeV/c. Comparison of the data to an N-body Coulomb-trajectory code shows a decrease of one order of magnitude in the fragment emission time in the excitation energy interval 2-5A MeV, followed by a nearly constant breakup time at higher excitation energy. The observed decrease in emission time is shown to be strongly correlated with the increase of the fragment emission probability, and the onset of thermally-induced radial expansion. This result is interpreted as evidence consistent with a transition from surface-dominated to bulk emission expected for spinodal decomposition.

  13. Investigation on surface figuration and microstructure of laser glazed nanostructure zirconia thermal barrier coatings

    Institute of Scientific and Technical Information of China (English)

    HUANG Binghua; WANG Hongying; HAO Yunfei; TANG Weijie

    2009-01-01

    CO2 continuous wave laser beam had been applied to the laser glazing of plasma sprayed nanostructure zirconia thermal barrier coatings. The effects of luser glazing processing parameters on the surface figuration and microstructure change had been carried out, the microstructure and phase composition of the coatings had been evaluated by the scanning electron microscope (SEM) and the X-ray diffraction (XRD). SEM observation indicates that the microstructure of the as-glazed coating could be altered from single columnar structure to a combination of the columnar grain and fine equiaxed grain with the different laser glazing conditions. XRD analysis illustrates that the predominance phase of the as-glazed coating is the metastable tetragonal phase, and the glazed coating with the single columnar structure has shown the clear orientation in (220) and (400) peaks while the other coatings do not show that.

  14. Analysis of organic contaminants from silicon wafer and disk surfaces by thermal desorption-GC-MS

    Science.gov (United States)

    Camenzind, Mark J.; Ahmed, Latif; Kumar, Anurag

    1999-03-01

    Organic contaminants can affect semiconductor wafer processing including gate oxide integrity, polysilicon growth, deep ultraviolet photoresist line-width, and cleaning & etching steps. Organophosphates are known to counter dope silicon wafers. Organic contaminants in disk drives can cause failures due to stiction or buildup on the heads. Therefore, it is important to identify organic contaminants adsorbed on wafer or disk surfaces and find their sources so they can be either completely eliminated or at least controlled. Dynamic headspace TD-GC-MS (Thermal Desorption-Gas Chromatography-Mass Spectrometry) methods are very sensitive and can be used to identify organic contaminants on disks and wafers, in air, or outgassing from running drives or their individual components.

  15. Effect of surface modification of Grewia optiva fibres on their physicochemical and thermal properties

    Indian Academy of Sciences (India)

    Amar S Singha; Ashvinder K Rana

    2012-12-01

    This paper deals with the surface modification of Grewia optiva fibre through benzoylation and graft copolymerization process. Benzoylation of Grewia optiva fibre has been carried out on mercerized fibre with varying concentrations of benzoyl chloride solution. Graft copolymerization of acrylonitrile (AN) onto Grewia optiva fibre was carried out with ceric ammonium nitrate as the redox initiator in aqueous medium under the influence of microwave radiation. Raw, graft copolymerized and benzoylated fibres were subjected to evaluation of some of their properties like swelling behaviour, moisture absorbance and chemical resistance behaviour. It has been observed that 5% benzoyl chloride treated and graft copolymerized Grewia optiva show more resistance towards moisture, water and chemicals when compared with that of raw fibre. Further morphological, structural changes, thermal stability and crystallinity of raw, graft copolymerized, pretreated and benzoylated fibres have also been studied by SEM, FTIR, TGA and XRD techniques.

  16. Enhanced active aluminum content and thermal behaviour of nano-aluminum particles passivated during synthesis using thermal plasma route

    Energy Technology Data Exchange (ETDEWEB)

    Mathe, Vikas L., E-mail: vlmathe@physics.unipune.ac.in [Department of Physics, Savitribai Phule Pune University, Pune 411007, Maharashtra (India); Varma, Vijay; Raut, Suyog [Department of Physics, Savitribai Phule Pune University, Pune 411007, Maharashtra (India); Nandi, Amiya Kumar; Pant, Arti; Prasanth, Hima; Pandey, R.K. [High Energy Materials Research Lab, Sutarwadi, Pune 411021, Maharashtra (India); Bhoraskar, Sudha V. [Department of Physics, Savitribai Phule Pune University, Pune 411007, Maharashtra (India); Das, Asoka K. [Utkal University, VaniVihar, Bhubaneswar, Odisha 751004 (India)

    2016-04-15

    Graphical abstract: - Highlights: • Synthesis of nano crystalline Al (nAl) using DC thermal plasma reactor. • In situ passivation of nAl by palmitic acid and air. • Enhanced active aluminum content obtained for palmitic acid passivated nAl. • Palmitic acid passivated nAl are quite stable in humid atmospheres. - Abstract: Here, we report synthesis and in situ passivation of aluminum nanoparticles using thermal plasma reactor. Both air and palmitc acid passivation was carried out during the synthesis in the thermal plasma reactor. The passivated nanoparticles have been characterized for their structural and morphological properties using X-ray diffraction (XRD) and transmission electron microscopy (TEM) techniques. In order to understand nature of passivation vibrational spectroscopic analysis have been carried out. The enhancement in active aluminum content and shelf life for a palmitic acid passivated nano-aluminum particles in comparison to the air passivated samples and commercially available nano Al powder (ALEX) has been observed. Thermo-gravimetric analysis was used to estimate active aluminum content of all the samples under investigation. In addition cerimetric back titration method was also used to estimate AAC and the shelf life of passivated aluminum particles. Structural, microstructural and thermogravomateric analysis of four year aged passivated sample also depicts effectiveness of palmitic acid passivation.

  17. Enhanced surface plasmon polariton propagation induced by active dielectrics

    OpenAIRE

    Athanasopoulos, C.; Mattheakis, M.; Tsironis, G. P.

    2013-01-01

    We present numerical simulations for the propagation of surface plasmon polaritons in a dielectric-metal-dielectric waveguide using COMSOL multiphysics software. We show that the use of an active dielectric with gain that compensates metal absorption losses enhances substantially plasmon propagation. Furthermore, the introduction of the active material induces, for a specific gain value, a root in the imaginary part of the propagation constant leading to infinite propagation of the surface pl...

  18. A novel family of green ionic liquids with surface activities

    Institute of Scientific and Technical Information of China (English)

    ZHANG HaiBo; ZHOU XiaoHai; DONG JinFeng; ZHANG GaoYong; WANG CunXin

    2007-01-01

    Ionic liquids have many unique properties as a new and remarkable class of environmental benign solvents, which promises widespread applications in industry and other areas. However, the ionic liquids with surface activity are rarely reported. In this work, a series of novel ionic liquids was synthesized by using N-methyl-2-pyrrolidone and alkyl bromide. The physical properties of this family of ionic liquids have been characterized, which shows that these compounds have ionic liquids characteristics,surface activity and biocompatibility.

  19. Structural and compositional modification of a barium boroaluminosilicate glass surface by thermal poling

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Nicholas J. [The Pennsylvania State University, Department of Material Science and Engineering, Materials Research Institute, University Park, PA (United States); Science and Technology Division, Corning Incorporated, Corning, NY (United States); Pantano, Carlo G. [The Pennsylvania State University, Department of Material Science and Engineering, Materials Research Institute, University Park, PA (United States)

    2014-08-15

    In addition to inducing second-order nonlinear properties, significant structural and compositional alteration can be imparted to glass surfaces during the process of thermal poling. In this work, we focus on how thermal poling affects a structurally complex, nominally alkali-free boroaluminosilicate display glass composition. We provide evidence for electrolysis of the glass network, characterized by the migration of both cations (Ba{sup 2+}, Na{sup +}) and anions (O{sup -}, F{sup -}) towards opposing electrode interfaces. This process results in oxidation of the positively biased electrode and forms a network-former rich, modifier-depleted glass surface layer adjacent to the anodic interface. The modified glass layer thickness is qualitatively correlated to the oxidation resistance of the electrode material, while extrinsic ions such as H{sup +}/H{sub 3}O{sup +} at not found in the depletion layer to compensate for the migration of modifier cations out of the region. Rather, FTIR spectroscopy suggests a local restructuring of the B{sub 2}O{sub 3}-Al{sub 2}O{sub 3}-SiO{sub 2} network species to accommodate the charge imbalance created by the exodus of network-modifying cations, specifically the conversion of tetrahedral B(4) to trigonal B(3) as Ba or Na ions are removed from B-related sites in the parent network. The resultant poling-induced depletion layer exhibits enhanced hydrolytic resistance under acidic conditions, and the IR spectra are substantially unlike those produced by acid leaching the same glass. (orig.)

  20. Activated carbon fibers with a high content of surface functional groups by phosphoric acid activation of PPTA.

    Science.gov (United States)

    Castro-Muñiz, Alberto; Suárez-García, Fabián; Martínez-Alonso, Amelia; Tascón, Juan M D

    2011-09-01

    Activated carbon fibers (ACFs) were prepared by chemical activation of poly(p-phenylene terephthalamide (PPTA) with phosphoric acid, with a particular focus on the effects of impregnation ratio and carbonization temperature on both surface chemistry and porous texture. Thermogravimetric studies of the pyrolysis of PPTA impregnated with different amounts of phosphoric acid indicated that this reagent has a strong influence on the thermal degradation of the polymer, lowering the decomposition temperature and increasing the carbon yield. As concerns surface chemistry, TPD and chemical analysis results indicated that the addition of phosphoric acid increases the concentration of oxygenated surface groups, with a maximum at an impregnation ratio of 100 wt.%. The resulting materials present uncommon properties, namely a large amount of oxygen- and phosphorus-containing surface groups and a high nitrogen content. Porosity development following H(3)PO(4) activation was very significant, with values close to 1700 m(2)/g and 0.80 cm(3)/g being reached for the BET surface area and total pore volume, respectively. The pore size distributions remained confined to the micropore and narrow mesopore (<10 nm) range.

  1. Flightweight radiantly and actively cooled panel: Thermal and structural performance

    Science.gov (United States)

    Shore, C. P.; Nowak, R. J.; Kelly, H. N.

    1982-01-01

    A 2- by 4-ft flightweight panel was subjected to thermal/structural tests representative of design flight conditions for a Mach 6.7 transport and to off-design conditions simulating flight maneuvers and cooling system failures. The panel utilized Rene 41 heat shields backed by a thin layer of insulation to radiate away most of the 12 Btu/ft2-sec incident heating. A solution of ethylene glycol in water circulating through tubes in an aluminum-honeycomb-sandwich panel absorbed the remainder of the incident heating (0.8 Btu/sq ft-sec). The panel successfully withstood (1) 46.7 hr of radiant heating which included 53 thermal cycles and 5000 cycles of uniaxial inplane loading of + or - 1200 lfb/in; (2) simulated 2g-maneuver heating conditions and simulated cooling system failures without excessive temperatures on the structural panel; and (3) the extensive thermal/structural tests and the aerothermal tests reported in NASA TP-1595 without significant damage to the structural panel, coolant leaks, or hot-gas ingress to the structural panel.

  2. Thermal effects generated by high-intensity focused ultrasound beams at normal incidence to a bone surface.

    Science.gov (United States)

    Nell, Diane M; Myers, Matthew R

    2010-01-01

    Experiments and computations were performed to study factors affecting thermal safety when high-intensity focused ultrasound (HIFU) beams are normally incident (i.e., beam axis normal to the interface) upon a bone/soft-tissue interface. In particular, the temperature rise and thermal dose were determined as a function of separation between the beam focus and the interface. Under conditions representative of clinical HIFU procedures, it was found that the thermal dose at the bone surface can exceed the threshold for necrosis even when the beam focus is more than 4 cm from the bone. Experiments showed that reflection of the HIFU beam from the bone back into the transducer introduced temperature fluctuations of as much as +/-15% and may be an important consideration for safety analyses at sufficiently high acoustic power. The applicability of linear propagation models in predicting thermal dose near the interface was also addressed. Linear models, while underpredicting thermal dose at the focus, provided a conservative (slight overprediction) estimate of thermal dose at the bone surface. Finally, temperature rise due to absorption of shear waves generated by the HIFU beam in the bone was computed. Modeling shear-wave propagation in the thermal analysis showed that the predicted temperature rise off axis was as much as 30% higher when absorption of shear waves is included, indicating that enhanced heating due to shear-wave absorption is potentially important, even for normally incident HIFU beams.

  3. Interpreting Low Spatial Resolution Thermal Data from Active Volcanoes on Io and the Earth

    Science.gov (United States)

    Keszthelyi, L.; Harris, A. J. L.; Flynn, L.; Davies, A. G.; McEwen, A.

    2001-01-01

    The style of volcanism was successfully determined at a number of active volcanoes on Io and the Earth using the same techniques to interpret thermal remote sensing data. Additional information is contained in the original extended abstract.

  4. Surface functionalization on the thermal conductivity of graphene–polymer nanocomposites

    Directory of Open Access Journals (Sweden)

    Mingchao Wang

    2014-04-01

    Full Text Available Exploring thermal transport in graphene–polymer nanocomposite is significant to its applications with better thermal properties. Interfacial thermal conductance between graphene and polymer matrix plays a critical role in the improvement of thermal conductivity of graphene–polymer nanocomposite. Unfortunately, it is still challenging to understand the interfacial thermal transport between graphene nanofiller and polymer matrix at small material length scale. To this end, using nonequilibrium molecular dynamics (NEMD simulations, we investigate the interfacial thermal conductance of graphene–polyethylene (PE nanocomposite. The influence of functionalization with hydrocarbon chains on the interfacial thermal conductance of graphene–polymer nanocomposites was studied, taking into account the effects of model size and thermal conductivity of graphene. An analytical model is also used to calculate the thermal conductivity of nanocomposite. The results are considered to contribute to the development of new graphene–polymer nanocomposites with tailored thermal properties.

  5. New Activated Carbon with High Thermal Conductivity and Its Microwave Regeneration Performance

    Institute of Scientific and Technical Information of China (English)

    GU Xuexian; SU Zhanjun; XI Hongxia

    2016-01-01

    Using a walnut shell as a carbon source and ZnCl2 as an activating agent, we resolved the temperature gradient problems of activated carbon in the microwave desorption process. An appropriate amount of silicon carbide was added to prepare the composite activated carbon with high thermal conductivity while developing VOC adsorption-microwave regeneration technology. The experimental results show that the coefficient of thermal conductivity of SiC-AC is three times as much as those of AC and SY-6. When microwave power was 480 W in its microwave desorption , the temperature of the bed thermal desorption was 10℃ to 30℃below that of normal activated carbon prepared in our laboratory. The toluene desorption activation energy was 16.05 kJ∙mol-1, which was 15% less than the desorption activation energy of commercial activated carbon. This study testified that the process could maintain its high adsorption and regeneration desorption performances.

  6. Ultrasmooth reaction-sintered silicon carbide surface resulting from combination of thermal oxidation and ceria slurry polishing.

    Science.gov (United States)

    Shen, Xinmin; Dai, Yifan; Deng, Hui; Guan, Chaoliang; Yamamura, Kazuya

    2013-06-17

    An ultrasmooth reaction-sintered silicon carbide surface with an rms roughness of 0.424 nm is obtained after thermal oxidation for 30 min followed by ceria slurry polishing for 30 min. By SEM-EDX analysis, we investigated the thermal oxidation behavior of RS-SiC, in which the main components are Si and SiC. As the oxidation rate is higher in the area with defects, there are no scratches or cracks on the surface after oxidation. However, a bumpy structure is formed after oxidation because the oxidation rates of Si and SiC differ. Through a theoretical analysis of thermal oxidation using the Deal-Grove model and the removal of the oxide layer by ceria slurry polishing in accordance with the Preston equation, a model for obtaining an ultrasmooth surface is proposed and the optimal processing conditions are presented.

  7. A practical algorithm for estimating surface soil moisture using combined optical and thermal infrared data

    Science.gov (United States)

    Leng, Pei; Song, Xiaoning; Duan, Si-Bo; Li, Zhao-Liang

    2016-10-01

    Surface soil moisture (SSM) is a critical variable for understanding the energy and water exchange between the land and atmosphere. A multi-linear model was recently developed to determine SSM using ellipse variables, namely, the center horizontal coordinate (x0), center vertical coordinate (y0), semi-major axis (a) and rotation angle (θ), derived from the elliptical relationship between diurnal cycles of land surface temperature (LST) and net surface shortwave radiation (NSSR). However, the multi-linear model has a major disadvantage. The model coefficients are calculated based on simulated data produced by a land surface model simulation that requires sufficient meteorological measurements. This study aims to determine the model coefficients directly using limited meteorological parameters rather than via the complicated simulation process, decreasing the dependence of the model coefficients on meteorological measurements. With the simulated data, a practical algorithm was developed to estimate SSM based on combined optical and thermal infrared data. The results suggest that the proposed approach can be used to determine the coefficients associated with all ellipse variables based on historical meteorological records, whereas the constant term varies daily and can only be determined using the daily maximum solar radiation in a prediction model. Simulated results from three FLUXNET sites over 30 cloud-free days revealed an average root mean square error (RMSE) of 0.042 m3/m3 when historical meteorological records were used to synchronously determine the model coefficients. In addition, estimated SSM values exhibited generally moderate accuracies (coefficient of determination R2 = 0.395, RMSE = 0.061 m3/m3) compared to SSM measurements at the Yucheng Comprehensive Experimental Station.

  8. Structurally Integrated, Damage Tolerant Thermal Spray Coatings: Processing Effects on Surface and System Functionalities

    Science.gov (United States)

    Vackel, Andrew

    Thermal Spray (TS) coatings have seen extensive application as protective surfaces to enhance the service life of substrates prone to damage in their operating environment (wear, corrosion, heat etc.). With the advent of high velocity TS processes, the ability to deposit highly dense (>99%) metallic and cermet coatings has further enhanced the protective ability of these coatings. In addition to surface functionality, the influence of the coating application on the mechanical performance of a coated component is of great concern when such a component will experience either static or cyclic loading during service. Using a process mapping methodology, the processing-property interplay between coating materials meant to provide damage tolerant surface or for structural restoration are explored in terms of relevant mechanical properties. Most importantly, the residual stresses inherent in TS deposited coatings are shown to play a significant role in the integrated mechanical performance of these coatings. Unique to high velocity TS processes is the ability to produce compressive stresses within the deposit from the cold working induced by the high kinetic energy particles upon impact. The extent of these formation stresses are explored with different coating materials, as well as processing influence. The ability of dense TS coatings to carry significant structural load and synergistically strengthen coated tensile specimens is demonstrated as a function of coating material, processing, and thickness. The sharing of load between the substrate and otherwise brittle coating enables higher loads before yield for the bi-material specimens, offering a methodology to improve the tensile performance of coated components for structural repair or multi-functionality (surface and structure). The concern of cyclic fatigue damage in coated components is explored, since the majority of service application are designed for loading to be well below the yield point. The role of

  9. Thermal chemistry of copper acetamidinate atomic layer deposition precursors on silicon oxide surfaces studied by XPS

    Energy Technology Data Exchange (ETDEWEB)

    Yao, Yunxi; Zaera, Francisco, E-mail: zaera@ucr.edu [Department of Chemistry, University of California, Riverside, California 92521 (United States)

    2016-01-15

    The thermal surface chemistry of copper(I)-N,N′-di-sec-butylacetamidinate, [Cu({sup s}Bu-amd)]{sub 2}, a metalorganic complex recently proposed for the chemical-based deposition of copper films, has been characterized on SiO{sub 2} films under ultrahigh vacuum conditions by x-ray photoelectron spectroscopy (XPS). Initial adsorption at cryogenic temperatures results in the oxidation of the copper centers with Cu 2p{sub 3/2} XPS binding energies close to those seen for a +2 oxidation state, an observation that the authors interpret as the result of the additional coordination of oxygen atoms from the surface to the Cu atoms of the molecular acetamidinate dimer. Either heating to 300 K or dosing the precursor directly at that temperature leads to the loss of one of its two ligands, presumably via hydrogenation/protonation with a hydrogen/proton from a silanol group, or following a similar reaction on a defect site. By approximately 500 K the Cu 2p{sub 3/2}, C 1s, and N 1s XPS data suggest that the remaining acetamidinate ligand is displaced from the copper center and bonds to the silicon oxide directly, after which temperatures above 900 K need to be reached to promote further (and only partial) decomposition of those organic moieties. It was also shown that the uptake of the Cu precursor is self-limiting at either 300 or 500 K, although the initial chemistry is somewhat different at the two temperatures, and that the nature of the substrate also defines reactivity, with the thin native silicon oxide layer always present on Si(100) surfaces being less reactive than thicker films grown by evaporation, presumably because of the lower density of surface nucleation sites.

  10. Mars Thermal History: Core, Atmosphere, Mantle, Phobos and Surface (MaTH CAMPS)

    Science.gov (United States)

    Wicks, J. K.; Weller, M. B.; Towles, N. J.; Thissen, C.; Knezek, N. R.; Johnston, S.; Hongsresawat, S.; Duncan, M. S.; Black, B. A.; Schmerr, N. C.; Panning, M. P.; Montesi, L.; Manga, M.; Lognonne, P. H.

    2014-12-01

    The death of the Martian dynamo ~4.1 Ga and sustained volcanism throughout Martian history place fundamental constraints on the thermal history of the planet. To explore the implications for mantle structure, we constructed holistic models of Mars that include the core, mantle, lithosphere/surface, atmosphere, and an atmospheric capture of Phobos in a collaborative effort begun at the CIDER 2014 summer program. For our thermal model of the core, we employ an iterative solver and parameterized phase diagram to compute pressure, density, and temperature in the core for a variety of initial accretion temperatures and bulk compositions. We use this model to constrain core-mantle boundary (CMB) temperature and heat flow. We couple this model for the evolution of the core with a one-dimensional parameterized convection model for the mantle. The upper boundary condition is set by the state of the Martian atmosphere. We consider the effect of a distinct compositional layer at the base of the mantle that may represent dense magma ocean crystallization products or a primitive layer untouched by magma ocean processes. We find successful models that allow sufficient CMB heat flow to power an early dynamo and the potential of melt generation through extended periods of Mars' history. In addition to dynamo and magmatism timing, other diagnostics allow us to compare model outputs to modern observables. The mass, moment of inertia, and tidal Love number of our model planet are compared directly to measured values. Additionally, deformation and stress on the lithosphere due to internal volume changes and changes in surface loading predicted by our thermal evolution models could be recorded in the Martian crust. Finally, coupling temperature-dependent tidal dissipation affects Phobos' orbital secular evolution and gives constraint on mantle temperatures. These constraints are discussed for the different scenarios of Phobos capture. We present a suite of models that satisfy the

  11. Reducing Display Bottle Cooler Energy Consumption Using PCM As Active Thermal Storage

    OpenAIRE

    Beek, Marcel van; de Jong, Hans

    2014-01-01

    The final results of an analytical and experimental study in reducing the energy consumption of a display bottle cooler using Phase Change Material (PCM) as an active thermal storage are presented. The objective of the study was to design and built a 350 dm3 glass door bottle cooler having an appliance energy consumption reduction of over 75% compared to state of the art bottle coolers (2010 figures). Calculation results show that active thermal storage using PCM can be effectively applied to...

  12. Thermal Technology Development Activities at the Goddard Space Flight Center - 2001

    Science.gov (United States)

    Butler, Dan

    2002-01-01

    This presentation provides an overview of thermal technology development activities carried out at NASA's Goddard Space Flight Center during 2001. Specific topics covered include: two-phase systems (heat pipes, capillary pumped loops, vapor compression systems and phase change materials), variable emittance systems, advanced coatings, high conductivity materials and electrohydrodynamic (EHD) thermal coatings. The application of these activities to specific space missions is also discussed.

  13. Highly Efficient, Simplified, Solution-Processed Thermally Activated Delayed-Fluorescence Organic Light-Emitting Diodes.

    Science.gov (United States)

    Kim, Young-Hoon; Wolf, Christoph; Cho, Himchan; Jeong, Su-Hun; Lee, Tae-Woo

    2016-01-27

    Highly efficient, simplified, solution-processed thermally activated delayed-fluorescence organic light-emitting diodes can be realized by using pure-organic thermally activated delayed fluorescence emitters and a multifunctional buffer hole-injection layer, in which high EQE (≈24%) and current efficiency (≈73 cd A(-1) ) are demonstrated. High-efficiency fluorescence red-emitting and blue-emitting devices can also be fabricated in this manner.

  14. Recent National Solar Thermal Test Facility activities, in partnership with industry

    Science.gov (United States)

    Ghanbari, Cherly; Cameron, Christopher P.; Ralph, Mark E.; Pacheco, James E.; Rawlinson, K. Scott; Evans, Lindsey R.

    The National Solar Thermal Test Facility (NSTTF) at Sandia National Laboratories in Albuquerque, New Mexico, USA conducts testing of solar thermal components and systems, funded primarily by the US Department of Energy. Activities are conducted in support of Central Receiver Technology, Distributed Receiver Technology and Design Assistance projects. All activities are performed in support of various cost-shared government/industry joint ventures and, on a design assistance basis, in support of a number of other industry partners.

  15. Recent National Solar Thermal Test Facility activities, in partnership with industry

    Energy Technology Data Exchange (ETDEWEB)

    Ghanbari, C.; Cameron, C.P.; Ralph, M.E.; Pacheco, J.E.; Rawlinson, K.S. [Sandia National Labs., Albuquerque, NM (United States); Evans, L.R. [Ewing Technical Design, Albuquerque, NM (United States)

    1994-10-01

    The National Solar Thermal Test Facility (NSTTF) at Sandia National Laboratories in Albuquerque, New Mexico, USA conducts testing of solar thermal components and systems, funded primarily by the US Department of Energy. Activities are conducted in support of Central Receiver Technology, Distributed Receiver Technology and Design Assistance projects. All activities are performed in support of various cost-shared government/industry joint ventures and, on a design assistance basis, in support of a number of other industry partners.

  16. Thermal effects of λ = 808 nm GaAlAs diode laser irradiation on different titanium surfaces.

    Science.gov (United States)

    Giannelli, Marco; Lasagni, Massimo; Bani, Daniele

    2015-12-01

    Diode lasers are widely used in dental laser treatment, but little is known about their thermal effects on different titanium implant surfaces. This is a key issue because already a 10 °C increase over the normal body temperature can induce bone injury and compromise osseo-integration. The present study aimed at evaluating the temperature changes and surface alterations experienced by different titanium surfaces upon irradiation with a λ = 808 nm diode laser with different settings and modalities. Titanium discs with surfaces mimicking different dental implant surfaces including TiUnite and anodized, machined surfaces were laser-irradiated in contact and non-contact mode, and with and without airflow cooling. Settings were 0.5-2.0 W for the continuous wave mode and 10-45 μJ, 20 kHz, 5-20 μs for the pulsed wave mode. The results show that the surface characteristics have a marked influence on temperature changes in response to irradiation. The TiUnite surface, corresponding to the osseous interface of dental implants, was the most susceptible to thermal rise, while the machined surfaces, corresponding to the implant collar, were less affected. In non-contact mode and upon continuous wave emission, the temperature rose above the 50 °C tissue damage threshold. Scanning electron microscopy investigation of surface alterations revealed that laser treatment in contact mode resulted in surface scratches even when no irradiation was performed. These findings indicate that the effects of diode laser irradiation on implant surfaces depend on physical features of the titanium coating and that in order to avoid thermal or physical damage to implant surface the irradiation treatment has to be carefully selected.

  17. Bright sand/dark dust: The identification of active sand surfaces on the Earth and Mars

    Science.gov (United States)

    Blount, H. G., II; Greeley, R.; Christensen, P. R.; Arvidson, R.

    1987-05-01

    Field studies and analysis of LANDSAT Thematic Mapper data in the Gran Desierto, Mexico may shed light on a technique to distinguish active from inactive (relict) sand surfaces. Active sand bodies in the study area are consistently brighter (by an average of 20%) at visual and near infrared wavelengths and darker at thermal infrared wavelengths than compositionally similar inactive sands. The reasons for the albedo difference between active and inactive sands are reviewed and the mixing model of Johnson et al. is examined for tracing the provenance of sands based on albedo and spectral variations. Portions of the wavelengths covered by the Mars Orbiter correspond to the Thematic Mapper data. The identification of active sands on Earth, with a priori knowledge of bulk composition and grain size distribution, may allow the remote mapping of active sand surfaces on Mars. In conjuction with thermal infrared remote sensing for composition, it may also provide a method for the remote determination of grain size distributions within sand/silt mixtures.

  18. The Solar Thermal Design Assistance Center report of its activities and accomplishments in Fiscal Year 1993

    Energy Technology Data Exchange (ETDEWEB)

    Menicucci, D.F.

    1994-03-01

    The Solar Thermal Design Assistance Center (STDAC) at Sandia National Laboratories is a resource provided by the US Department of Energy`s Solar Thermal Program. Its major objectives are to accelerate the use of solar thermal systems through (a) direct technical assistance to users, (b) cooperative test, evaluation, and development efforts with private industry, and (c) educational outreach activities. This report outlines the major activities and accomplishments of the STDAC in Fiscal Year 1993. The report also contains a comprehensive list of persons who contacted the STDAC by telephone for information or technical consulting.

  19. An Active Thermal Control System for Extreme Environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Venus retains many secrets pertaining to its formation and evolution. NASA is interested in expanding its ability to explore the deep atmosphere and surface of Venus...

  20. Dynamics of freely suspended lyotropic films. I. An inelastic light scattering study of thermal surface fluctuations

    Science.gov (United States)

    Young, Charles Y.; Clark, Noel A.

    1981-04-01

    We have studied the spectrum and intensity of light scattered by thermal surface displacement fluctuations on freely suspended lyotropic films. Films consisted of a liquid core and surface soap layers and were drawn from solution containing water, glycerol, NaCl, and the ionic surfactant hexadecyltrimethyl ammonium bromide (HTAB). Two modes were observed: a propagating undulation mode in which the film surfaces move together and a damped peristaltic mode having oppositely moving surface soap layers. Dispersion relations for these modes, obtained from the dependence of the scattered light intensity correlation function on film thickness h and wave vector k, confirm the macroscopic hydrodynamic description of film motion. In particular, the overdamped peristaltic mode is shown to involve Poiseuille flow of the fluid core with the flow velocity zero within 2 Å of the surfactant-solution interface, indicating no significant slip or rigid interfacial water layer. No evidence of dispersion in the effective viscosity of the fluid core h(k,w) over the range 0surface waves in fluids. The dynamic surface tension term s(k,w) for k˜106 cm-1 and w˜6×10 sec-1 was found to be the same as the static value within experimental error. Analysis of the total scattered intensity and of the peristaltic mode dynamics allows the determination of R(h), that part of the film pressure due to electrostatic repulsive and van der Waals attractive forces. The measured R(h) are well represented by the sum of a repulsive screened electrostatic interaction and an attractive van der Waals term. The screened electrostatic interaction is consistent with the concentration of NaCl used and the attractive part of R could be fitted equally well by the simple nonretarded van der Waals form for a uniform dielectric slab, or the Ninham

  1. Biomedical Applications of Thermally Activated Shape Memory Polymers

    Energy Technology Data Exchange (ETDEWEB)

    Small IV, W; Singhal, P; Wilson, T S; Maitland, D J

    2009-04-10

    Shape memory polymers (SMPs) are smart materials that can remember a primary shape and can return to this primary shape from a deformed secondary shape when given an appropriate stimulus. This property allows them to be delivered in a compact form via minimally invasive surgeries in humans, and deployed to achieve complex final shapes. Here we review the various biomedical applications of SMPs and the challenges they face with respect to actuation and biocompatibility. While shape memory behavior has been demonstrated with heat, light and chemical environment, here we focus our discussion on thermally stimulated SMPs.

  2. Real-time thermal imaging of solid oxide fuel cell cathode activity in working condition.

    Science.gov (United States)

    Montanini, Roberto; Quattrocchi, Antonino; Piccolo, Sebastiano A; Amato, Alessandra; Trocino, Stefano; Zignani, Sabrina C; Faro, Massimiliano Lo; Squadrito, Gaetano

    2016-09-01

    Electrochemical methods such as voltammetry and electrochemical impedance spectroscopy are effective for quantifying solid oxide fuel cell (SOFC) operational performance, but not for identifying and monitoring the chemical processes that occur on the electrodes' surface, which are thought to be strictly related to the SOFCs' efficiency. Because of their high operating temperature, mechanical failure or cathode delamination is a common shortcoming of SOFCs that severely affects their reliability. Infrared thermography may provide a powerful tool for probing in situ SOFC electrode processes and the materials' structural integrity, but, due to the typical design of pellet-type cells, a complete optical access to the electrode surface is usually prevented. In this paper, a specially designed SOFC is introduced, which allows temperature distribution to be measured over all the cathode area while still preserving the electrochemical performance of the device. Infrared images recorded under different working conditions are then processed by means of a dedicated image processing algorithm for quantitative data analysis. Results reported in the paper highlight the effectiveness of infrared thermal imaging in detecting the onset of cell failure during normal operation and in monitoring cathode activity when the cell is fed with different types of fuels.

  3. Surface passivation of efficient nanotextured black silicon solar cells using thermal atomic layer deposition.

    Science.gov (United States)

    Wang, Wei-Cheng; Lin, Che-Wei; Chen, Hsin-Jui; Chang, Che-Wei; Huang, Jhih-Jie; Yang, Ming-Jui; Tjahjono, Budi; Huang, Jian-Jia; Hsu, Wen-Ching; Chen, Miin-Jang

    2013-10-09

    Efficient nanotextured black silicon solar cells passivated by an Al2O3 layer are demonstrated. The broadband antireflection of the nanotextured black silicon solar cells was provided by fabricating vertically aligned silicon nanowire (SiNW) arrays on the n(+) emitter. A highly conformal Al2O3 layer was deposited upon the SiNW arrays by the thermal atomic layer deposition (ALD) based on the multiple pulses scheme. The nanotextured black silicon wafer covered with the Al2O3 layer exhibited a low total reflectance of ∼1.5% in a broad spectrum from 400 to 800 nm. The Al2O3 passivation layer also contributes to the suppressed surface recombination, which was explored in terms of the chemical and field-effect passivation effects. An 8% increment of short-circuit current density and 10.3% enhancement of efficiency were achieved due to the ALD Al2O3 surface passivation and forming gas annealing. A high efficiency up to 18.2% was realized in the ALD Al2O3-passivated nanotextured black silicon solar cells.

  4. Chemical Surface, Thermal and Electrical Characterization of Nafion Membranes Doped with IL-Cations

    Directory of Open Access Journals (Sweden)

    María del Valle Martínez de Yuso

    2014-04-01

    Full Text Available Surface and bulk changes in a Nafion membrane as a result of IL-cation doping (1-butyl-3-methylimidazolium tetrafluoroborate or BMIM+BF4 and phenyltrimethylammonium chloride or TMPA+Cl− were studied by X-ray photoelectron spectroscopy (XPS, contact angle, differential scanning calorimetry (DSC and impedance spectroscopy (IS measurements performed with dry samples after 24 h in contact with the IL-cations BMIM+ and TMPA+. IL-cations were selected due to their similar molecular weight and molar volume but different shape, which could facilitate/obstruct the cation incorporation in the Nafion membrane structure by proton/cation exchange mechanism. The surface coverage of the Nafion membrane by the IL-cations was confirmed by XPS analysis and contact angle, while the results obtained by the other two techniques (DSC and IS seem to indicate differences in thermal and electrical behaviour depending on the doping-cation, being less resistive the Nafion/BMIM+ membrane. For that reason, determination of the ion transport number was obtained for this membrane by measuring the membrane or concentration potential with the samples in contact with HCl solutions at different concentrations. The comparison of these results with those obtained for the original Nafion membrane provides information on the effect of IL-cation BMIM+ on the transport of H+ across wet Nafion/BMIM+ doped membranes.

  5. Surface tungsten reduction during thermal decomposition of ammonium paratungstate tetrahydrate in oxidising atmosphere: A paradox?

    Energy Technology Data Exchange (ETDEWEB)

    Fait, Martin J.G., E-mail: martin.fait@catalysis.de [Leibniz-Institut für Katalyse e.V., Albert-Einstein-Strasse 29a, 18059 Rostock (Germany); Radnik, Jörg [Leibniz-Institut für Katalyse e.V., Albert-Einstein-Strasse 29a, 18059 Rostock (Germany); Lunk, Hans-Joachim [2858 Lake RD, Towanda, PA 18848 (United States)

    2016-06-10

    Highlights: • Detection of reduced tungsten ions at the solid’s surface in oxidising atmosphere. • Detection of gaseous ammonia liberated as oxidising agent. • Detection of ammonia’s oxidation products. • Quantification of the ammonia/tungsten redox process. - Abstract: The interaction of ammonia, liberated during thermal decomposition of ammonium paratungstate tetrahydrate in oxidising atmosphere, with tungsten has been studied employing a conventional microbalance combined with MS (Setaram’s instrument Sensys). Applying XPS a partial reduction of tungsten at the surface with the minimal tungsten oxidation number of +5.3 for a sample generated at 293 °C was detected. The balancing oxidation of ammonia to nitrogen/nitrogen oxides has been proven by MS. An amount of 0.049 mol e{sup −} per mol W was transferred which resulted in an ammonia conversion degree from 2.1 mol% (NO{sub 2} formation) to 3.0 mol% (N{sub 2} formation).

  6. Thermocouple Errors when Mounted on Cylindrical Surfaces in Abnormal Thermal Environments.

    Energy Technology Data Exchange (ETDEWEB)

    Nakos, James T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Suo-Anttila, Jill M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Zepper, Ethan T. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Koenig, Jerry J [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Valdez, Vincent A. [ECI Inc., Albuquerque, NM (United States)

    2017-05-01

    Mineral-insulated, metal-sheathed, Type-K thermocouples are used to measure the temperature of various items in high-temperature environments, often exceeding 1000degC (1273 K). The thermocouple wires (chromel and alumel) are protected from the harsh environments by an Inconel sheath and magnesium oxide (MgO) insulation. The sheath and insulation are required for reliable measurements. Due to the sheath and MgO insulation, the temperature registered by the thermocouple is not the temperature of the surface of interest. In some cases, the error incurred is large enough to be of concern because these data are used for model validation, and thus the uncertainties of the data need to be well documented. This report documents the error using 0.062" and 0.040" diameter Inconel sheathed, Type-K thermocouples mounted on cylindrical surfaces (inside of a shroud, outside and inside of a mock test unit). After an initial transient, the thermocouple bias errors typically range only about +-1-2% of the reading in K. After all of the uncertainty sources have been included, the total uncertainty to 95% confidence, for shroud or test unit TCs in abnormal thermal environments, is about +-2% of the reading in K, lower than the +-3% typically used for flat shrouds. Recommendations are provided in Section 6 to facilitate interpretation and use of the results. .

  7. Surface structure of crystalline and amorphous chromia catalysts for the selective catalytic reduction of nitric oxide. 2. Diffuse reflectance FTIR study of thermal treatment and oxygen adsorption

    Energy Technology Data Exchange (ETDEWEB)

    Schraml-Marth, M.; Wokaun, A. (Univ. of Bayreuth (Germany)); Curry-Hyde, H.E.; Baiker, A. (Swiss Federal Inst. of Tech., Zuerich (Switzerland))

    1992-02-01

    The activation of crystalline and amorphous chromia surfaces by thermal pretreatment in argon and oxygen adsorption at 473 K has been studied by diffuse reflectance FTIR and Raman spectroscopy. The formation of coordinatively unsaturated chromium sites during thermal activation is monitored by observing the evolution of Cr{double bond}O stretching absorptions both in the fundamental and overtone regions of the FTIR spectrum. On {alpha}-Cr{sub 2}O{sub 3}, labile surface oxygen species are largely removed at 498 K, whereas on the amorphous chromia surface, labile oxygen is more tightly bound. As a consequence, coordinatively unsaturated chromium sites are generated on amorphous chromia to a lesser extent than on {alpha}-Cr{sub 2}O{sub 3}. Upon high-temperature oxygen treatment, O{sub 2} is dissociatively adsorbed. Coordinatively unsaturated sites are occupied by the added oxygen, as manifested by an increase in the number of Cr{double bond}O oscillators. Fine structure in the Cr{double bond}O absorptions of the amorphous chromia is observed for the first time, and is tentatively assigned to various types of surface sites. Raman spectroscopic characterization of the amorphous chromia surface reveals laser-induced dehydration and creation of coordinatively unsaturated surface Cr{double bond}O sites, accompanied by progressive crystallization of the amorphous substrate. Differences between crystalline and amorphous chromia with respect to their SCR activity are correlated with the higher density of labile oxygen species available on the surface of amorphous chromia under SCR reaction conditions (423-473 K).

  8. Active downhole thermal property measurement system for characterization of gas hydrate-bearing formations

    Energy Technology Data Exchange (ETDEWEB)

    Fukuhara, Masafumi; Fujii, Kasumi; Tertychnyi, Vladimir; Shandrygin, Alexander; Popov, Yuri; Matsubayashi, Osamu; Kusaka, Koji; Yasuda, Masato

    2005-07-01

    Gas hydrates dissociate or form when temperature and/or pressure conditions cross the equilibrium border. When we consider gas hydrates as an energy resource, understanding those parameters is very important for developing efficient production schemes. Therefore, thermal measurement is one of the key components of the characterization of the gas hydrate-bearing formation, not only statically but also dynamically. To estimate thermal properties such as thermal conductivity and diffusivity of subsurface formations, the conventional method has been to monitor temperature passively at several underground locations and interpret collected information with assumptions such as steady heat flow or relaxation from thermal disturbance by fluid flow, etc. Because the thermal properties are estimated based on several assumptions, these passive measurement methods sometimes leave a lot of uncertainties. On the other hand, active thermal property measurement, which could minimize those uncertainties, is commonly used in a laboratory and many types of equipment exist commercially for the purpose. The concept of measurement is very simple: creating a known thermal disturbance with a thermal source and then monitoring the response of the specimen. However, simply applying this method to subsurface formation measurement has many technical and logistical difficulties. In this paper, newly developed thermal property measurement equipment and its measurement methodology are described. Also discussed are the theoretical background for the application of the methodology to a gas hydrate-bearing formation through numerical simulation and the experimental results of laboratory mockup in a controlled environment. (Author)

  9. The detection of intestinal spike activity on surface electroenterograms

    Energy Technology Data Exchange (ETDEWEB)

    Ye-Lin, Y; Garcia-Casado, J; Martinez-de-Juan, J L; Prats-Boluda, G [Instituto interuniversitario de investigacion en bioingenierIa y tecnologIa orientada al ser humano (I3BH), Universidad Politecnica de Valencia, Camino de Vera, s/n, Ed. 8E, Acceso N, 2a, planta 46022 Valencia (Spain); Ponce, J L [Department of Surgery, Hospital Universitario La Fe de Valencia, Avenida Campanar n0. 51, 46009 Valencia (Spain)], E-mail: yiye@eln.upv.es, E-mail: jgarciac@eln.upv.es, E-mail: jlmartinez@eln.upv.es, E-mail: geprabo@eln.upv.es, E-mail: drjlponce@ono.com

    2010-02-07

    Myoelectrical recording could provide an alternative technique for assessing intestinal motility, which is a topic of great interest in gastroenterology since many gastrointestinal disorders are associated with intestinal dysmotility. The pacemaker activity (slow wave, SW) of the electroenterogram (EEnG) has been detected in abdominal surface recordings, although the activity related to bowel contractions (spike bursts, SB) has to date only been detected in experimental models with artificially favored electrical conductivity. The aim of the present work was to assess the possibility of detecting SB activity in abdominal surface recordings under physiological conditions. For this purpose, 11 recording sessions of simultaneous internal and external myolectrical signals were conducted on conscious dogs. Signal analysis was carried out in the spectral domain. The results show that in periods of intestinal contractile activity, high-frequency components of EEnG signals can be detected on the abdominal surface in addition to SW activity. The energy between 2 and 20 Hz of the surface myoelectrical recording presented good correlation with the internal intestinal motility index (0.64 {+-} 0.10 for channel 1 and 0.57 {+-} 0.11 for channel 2). This suggests that SB activity can also be detected in canine surface EEnG recording.

  10. Thermally activated repolarization of antiferromagnetic particles: Monte Carlo dynamics

    Science.gov (United States)

    Soloviev, S. V.; Popkov, A. F.; Knizhnik, A. A.; Iskandarova, I. M.

    2017-02-01

    Based on the equation of motion of an antiferromagnetic moment, taking into account a random field of thermal fluctuations, we propose a Monte Carlo (MC) scheme for the numerical simulation of the evolutionary dynamics of an antiferromagnetic particle, corresponding to the Langevin dynamics in the Kramers theory for the two-well potential. Conditions for the selection of the sphere of fluctuations of random deviations of the antiferromagnetic vector at an MC time step are found. A good agreement with the theory of Kramers thermal relaxation is demonstrated for varying temperatures and heights of energy barrier over a wide range of integration time steps in an overdamped regime. Based on the developed scheme, we performed illustrative calculations of the temperature drift of the exchange bias under the fast annealing of a ferromagnet-antiferromagnet structure, taking into account the random variation of anisotropy directions in antiferromagnetic grains and their sizes. The proposed approach offers promise for modeling magnetic sensors and spintronic memory devices containing heterostructures with antiferromagnetic layers.

  11. Thermal oxidation of the surface of binary aluminum alloys with rare-earth metals

    Science.gov (United States)

    Akashev, L. A.; Popov, N. A.; Kuznetsov, M. V.; Shevchenko, V. G.

    2015-05-01

    The kinetics of oxidation of the surface of Al alloys with 1-2.5 at % rare-earth metals (REMs) at 400-500°C in air was studied by ellipsometry and X-ray photoelectron spectroscopy (XPS). The addition (1-2.5 at % REM) of all rare-earth metals to aluminum was shown to increase the thickness of the oxide layer. The addition of surfactant and chemically active REMs (Yb, Sm, La, and Ce) increased the rate of oxidation of solid aluminum most effectively. The oxidation can be accelerated by the polymorphic transformations of the individual REM oxides in the film. The surface activity of Sm with respect to solid Al was confirmed by XRS.

  12. Acid Aging Effects on Surfaces of PTFE Gaskets Investigated by Thermal Analysis

    Directory of Open Access Journals (Sweden)

    C. Fragassa

    2016-12-01

    Full Text Available This paper investigates the effect of a prolonged acid attack on the surface of PTFE by Thermogravimetric Analysis (TGA and Differential Scanning Calorimetry (DSC. PTFE is very non-reactive, partly because of the strength of carbon–fluorine bonds and for its high crystallinity, and, as a consequence, it is often used in containers and pipework with reactive and corrosive chemicals. The PTFE under analysis is commercialized by two alternative producers in form of Teflon tapes. These tapes are adopted, as gaskets, in process plants where tires moulds are cleaned by acid solutions inside a multistage ultrasonic process. In this case, PTFE shows, in a relatively short operation time, inexplicably phenomena of surface degradation, which could be related, in general terms, to an acid attack. But, even considering the combined effect of ultrasonic waves, temperature, humidity and acid attack, the PTFE properties of resistance nominally exclude the risk of the extreme erosion phenomena as observed. The present experimental research aim at investigating this contradiction. A possible explanation could be related to the presence in the cleaning solution of unexpected fluorides, able to produce fluorinating agents and, thus, degrade carbon-fluorine bonds. Considering more the 300 chemical elements a tire compound consists in, it is really complex to preserve the original chemical composition of the cleaning solution. In this research PTFE samples have been treated with different mixtures of acids with the aim at investigating the different aging effects. The thermal analysis has permitted the experimental characterization of PTFE surface properties after acid attack, providing evidence of the degradation phenomena. In particular, the different acid treatments adopted for accelerating the aging of gaskets have highlighted the different behaviour of the PTFE matrix, but also differences between manufacturers.

  13. Influence of diamond surface termination on thermal boundary conductance between Al and diamond

    Energy Technology Data Exchange (ETDEWEB)

    Monachon, Christian; Weber, Ludger [Laboratoire de Metallurgie Mecanique, Ecole Polytechnique Federale de Lausanne, Lausanne (Switzerland)

    2013-05-14

    The effect of diamond surface treatment on the Thermal Boundary Conductance (TBC) between Al and diamond is investigated. The treatments consist in either of the following: exposition to a plasma of pure Ar, Ar:H and Ar:O, and HNO{sub 3}:H{sub 2}SO{sub 4} acid dip for various times. The surface of diamond after treatment is analyzed by X-ray Photoelectron Spectroscopy, revealing hydrogen termination for the as-received and Ar:H plasma treated samples, pure sp{sup 2} termination for Ar treated ones and oxygen (keton-like) termination for the other treatments. At ambient, all the specific treatments improve the TBC between Al and diamond from 23 {+-} 2 MW m{sup -2} K{sup -1} for the as-received to 65 {+-} 5, 125 {+-} 20, 150 {+-} 20, 180 {+-} 20 MW m{sup -2} K{sup -1} for the ones treated by Ar:H plasma, acid, pure Ar plasma, and Ar:O plasma with an evaporated Al layer on top, respectively. The effect of these treatments on temperature dependence are also observed and compared with the most common models available in the literature as well as experimental values in the same system. The results obtained show that the values measured for an Ar:O plasma treated diamond with Al sputtered on top stay consistently higher than the values existing in the literature over a temperature range from 78 to 290 K, probably due a lower sample surface roughness. Around ambient, the TBC values measured lay close to or even somewhat above the radiation limit, suggesting that inelastic or electronic processes may influence the transfer of heat at this metal/dielectric interface.

  14. Analysis of Sensory/Active Piezoelectric Composite Structures in Thermal Environments

    Science.gov (United States)

    Lee, Ho-Jun; Saravanos, Dimitris A.

    1996-01-01

    Although there has been extensive development of analytical methods for modeling the behavior of piezoelectric structures, only a limited amount of research has been performed concerning the implications of thermal effects on both the active and sensory response of smart structures. Thermal effects become important when the piezoelectric structure has to operate in either extremely hot or cold temperature environments. Consequently, the purpose of this paper is to extend the previously developed discrete layer formulation of Saravanos and Heyliger to account for the coupled mechanical, electrical, and thermal response in modern smart composite beams. The mechanics accounts for thermal effects which may arise in the elastic and piezoelectric media at the material level through the constitutive equations. The displacements, electric potentials, and temperatures are introduced as state variables, allowing them to be modeled as variable fields through the laminate thickness. This unified representation leads to an inherent capability to model both the active compensation of thermal distortions in smart structures and the resultant sensory voltage when thermal loads are applied. The corresponding finite element formulation is developed and numerical results demonstrate the ability to model both the active and sensory modes of composite beams with heterogeneous plies with attached piezoelectric layers under thermal loadings.

  15. Surface activity, lipid profiles and their implications in cervical cancer.

    Directory of Open Access Journals (Sweden)

    Preetha A

    2005-01-01

    Full Text Available Background: The profiles of lipids in normal and cancerous tissues may differ revealing information about cancer development and progression. Lipids being surface active, changes in lipid profiles can manifest as altered surface activity profiles. Langmuir monolayers offer a convenient model for evaluating surface activity of biological membranes. Aims: The aims of this study were to quantify phospholipids and their effects on surface activity of normal and cancerous human cervical tissues as well as to evaluate the role of phosphatidylcholine (PC and sphingomyelin (SM in cervical cancer using Langmuir monolayers. Methods and Materials: Lipid quantification was done using thin layer chromatography and phosphorus assay. Surface activity was evaluated using Langmuir monolayers. Monolayers were formed on the surface of deionized water by spreading tissue organic phase corresponding to 1 mg of tissue and studying their surface pressure-area isotherms at body temperature. The PC and SM contents of cancerous human cervical tissues were higher than those of the normal human cervical tissues. Role of PC and SM were evaluated by adding varying amounts of these lipids to normal cervical pooled organic phase. Statistical analysis: Student′s t-test (p < 0.05 and one-way analysis of variance (ANOVA was used. Results: Our results reveals that the phosphatidylglycerol level in cancerous cervical tissue was nearly five folds higher than that in normal cervical tissue. Also PC and sphingomyelin SM were found to be the major phospholipid components in cancerous and normal cervical tissues respectively. The addition of either 1.5 µg DPPC or 0.5 µg SM /mg of tissue to the normal organic phase changed its surface activity profile to that of the cancerous tissues. Statistically significant surface activity parameters showed that PC and SM have remarkable roles in shifting the normal cervical lipophilic surface activity towards that of cancerous lipophilic

  16. Surface Modification of Fly Ash for Active Catalysis

    Directory of Open Access Journals (Sweden)

    Deepti Jain

    2013-01-01

    Full Text Available Fly ash based effective solid base catalyst (KF/Al2O3/fly ash473, KF/Al2O3/fly ash673, and KF/Al2O3/fly ash873 was synthesized by loading KF over chemically and thermally activated fly ash. The chemical activation was done by treating fly ash with aluminum nitrate via precipitation method followed by thermal activation at 650°C to increase the alumina content in fly ash. The increased alumina content was confirmed by SEM-EDX analysis. The alumina enriched fly ash was then loaded with KF (10 wt% and calcined at three different temperatures 473 K, 673 K and 873 K. The amount of loaded KF was monitored by XRD, FTIR spectroscopy, SEM-EDX, TEM and Flame Atomic Absorption Spectrophotometer. The catalytic activities of the catalysts were tested in the Claisen-Schmidt condensation of benzaldehyde and 4-methoxybenzaldehyde with 2′-hydroxyacetophenone to produce 2′-hydroxychalcone and 4-methoxy-2′-hydroxychalcone respectively. Higher conversion (83% of benzaldehyde and (89% of 4-methoxybenzaldehyde reveals that among these heterogeneous catalysts KF/Al2O3/fly ash673 is very active.

  17. Synthesis and surface active properties of cationic surface active agents from crude rice bran oil

    Directory of Open Access Journals (Sweden)

    El-Dougdoug, W. I. A.

    1999-10-01

    Full Text Available Cationic surfactants of 2-hidroxy-3-(2- alkylamidopolyethyl amino propane-1-triethylammonium hydroxides (ix-xuia-d were prepared from fatty acids (ia-d [palmitic, stearic, oleic, linoleic acid] and mixed fatty acids of crude rice bran oil ie [RBO]. The reaction of these acids with ethylenediamine, diethylenetriamine, triethylenetetramine andletraethylenepentamine (iia-d produced (iii-viia-d. The produced amidopolyethylamine (iii-viia-d reacted with 2-epoxypropylenetriethylammonium chloride (viii to give the cationic surfactants (ix-xiiia-d . The produced derivatives were purified and characterized by microanalysis, molecular weight determination, infra-red (IR, and proton nuclear magnetic resonance (1H NMR spectra. The surface active properties and inhibition efficiency of the prepared cationic surfactants were determined.

    Se han preparado tensioactivos catiónicos de hidróxidos de! 2-hidroxi-3-(2-alquilamidopolietilamino propano-1;trietilamonio (ix-xiiia-d a partir de los ácidos grasos (ia-d [ácido palmítico, esteárico, oleico y linoleico] y mezclas de ácidos grasos de aceite de germen de arroz crudo ie [RBO]. La reacción de estos ácidos con etilenodiamina, dietilenotriamina, trietilenotetramina y tetraetilenopentamina (iia-d produjo los compuestos (iv-viia-d . Los amidopolietilaminos producidos (iii-viia-d reaccionaron con el cloruro de 2-epoxipropilenotrietilamonio (viii para dar los tensioactivos catiónicos (ix-xiiia-d. Los derivados producidos se purificaron y caracterizaron por microanálisis, determinación del peso molecular, espectros de infrarrojo (IR y resonancia magnética nuclear de protón (1H NMR. Se determinaron las propiedades tensioactivas y la eficacia de inhibición de los tensioactivos cati

  18. Non-thermal plasma technology for the development of antimicrobial surfaces: a review

    Science.gov (United States)

    Nikiforov, Anton; Deng, Xiaolong; Xiong, Qing; Cvelbar, U.; DeGeyter, N.; Morent, R.; Leys, Christophe

    2016-05-01

    Antimicrobial coatings are in high demand in many fields including the biomaterials and healthcare sectors. Within recent progress in nanoscience and engineering at the nanoscale, preparation of nanocomposite films containing metal nanoparticles (such as silver nanoparticles, copper nanoparticles, zinc oxide nanoparticles) is becoming an important step in manufacturing biomaterials with high antimicrobial activity. Controlled release of antibiotic agents and eliminating free nanoparticles are of equal importance for engineering antimicrobial nanocomposite materials. Compared to traditional chemical ‘wet’ methods, plasma deposition and plasma polymerization are promising approaches for the fabrication of nanocomposite films with the advantages of gas phase dry processes, effective use of chemicals and applicability to various substrates. In this article, we present a short overview of state-of-the-art engineering of antimicrobial materials based on the use of non-thermal plasmas at low and atmospheric pressure.

  19. Adsorption of anionic and cationic dyes on activated carbons with different surface chemistries.

    Science.gov (United States)

    Faria, P C C; Orfão, J J M; Pereira, M F R

    2004-04-01

    The influence of the surface chemical groups of an activated carbon on the removal of different classes of dyes is evaluated. Starting from the same material (NORIT GAC 1240 PLUS), the following treatments were carried out in order to produce a series of samples with different surface chemical properties but with no major differences in their textural properties: oxidation in the liquid phase with 6M HNO(3) and 10 M H(2)O(2) (acid materials) and heat treatment at 700 degrees C in H(2) or N(2) flow (basic materials). The specific micropores volume and mesopores surface area of the materials were obtained from N(2) adsorption equilibrium isotherms at 77K. The surface chemistry was characterised by temperature programmed desorption, by the determination of the point of zero charge (pH(pzc)) and by the evaluation of the acidity/basicity of the samples. Elemental and proximate analyses were also carried out. Equilibrium isotherms of selected dyes (an acid, a basic and a reactive dye) on the mentioned samples were obtained and the results discussed in relation to their surface chemistry. In general, the Langmuir model provided the best fit for the adsorption data. It is shown that the surface chemistry of the activated carbon plays a key role in dye adsorption performance. The basic sample obtained by thermal treatment under H(2) flow at 700 degrees C is the best material for the adsorption of all the tested dyes.

  20. Nuclear Thermal Rocket Element Environmental Simulator (NTREES) Upgrade Activities

    Science.gov (United States)

    Emrich, William

    2013-01-01

    A key technology element in Nuclear Thermal Propulsion is the development of fuel materials and components which can withstand extremely high temperatures while being exposed to flowing hydrogen. NTREES provides a cost effective method for rapidly screening of candidate fuel components with regard to their viability for use in NTR systems. The NTREES is designed to mimic the conditions (minus the radiation) to which nuclear rocket fuel elements and other components would be subjected to during reactor operation. The NTREES consists of a water cooled ASME code stamped pressure vessel and its associated control hardware and instrumentation coupled with inductive heaters to simulate the heat provided by the fission process. The NTREES has been designed to safely allow hydrogen gas to be injected into internal flow passages of an inductively heated test article mounted in the chamber.

  1. Performance of thermally activated dolomite for the treatment of Ni and Zn in contaminated neutral drainage.

    Science.gov (United States)

    Calugaru, Iuliana Laura; Neculita, Carmen Mihaela; Genty, Thomas; Bussière, Bruno; Potvin, Robin

    2016-06-05

    Intensive research is ongoing for developing low-cost and highly efficient materials in metal removal from contaminated effluents. The present study evaluated dolomite [CaMg(CO3)2], both raw and modified by thermal activation (charring), for Ni and Zn treatment in contaminated neutral drainage (CND). Batch adsorption testing (equilibrium and kinetics) were conducted at pH 6, to evaluate the performance of initial vs. modified dolomite, and to assess potential mechanisms of metal removal. Charring of dolomite led to a rigid and porous material, mainly consisting of CaCO3 and MgO, which showed a sorption capacity increased sevenfold for Zn and doubled for Ni, relative to the raw material. In addition, Freundlich model best described the sorption of the both metals by dolomite, whereas the Langmuir model best described their sorption on charred dolomite. Plausible mechanisms of metal removal include cation exchange, surface precipitation and sorption processes, with carbonate ions and magnesium oxides acting as active centers. Based on these results, charred dolomite seems a promising option for the efficient treatment of Ni and Zn in CND.

  2. Role of surface fixed charge in the surface passivation of thermal atomic layer deposited Al2O3 on crystalline-Si

    Science.gov (United States)

    Dou, Y. N.; He, Y.; Huang, C. Y.; Zhou, C. L.; Ma, X. G.; Chen, R.; Chu, J. H.

    2012-11-01

    In this work, surface passivation of thermal atomic layer deposited (ALD) Al2O3 films on Si has been investigated. A quantitative analysis shows that field-effect passivation based on surface fixed charge combined with chemical passivation is assumed to contribute to the passivation performance and that a low defect density is critical to passivation quality. The surface fixed negative charge, which is exponentially modulated from ˜0 cm-2 to -2×1012 cm-2 by annealing, is proposed to have arisen from the reconstruction of the interfacial SiO x layer.

  3. Casson fluid flow and heat transfer past an exponentially porous stretching surface in presence of thermal radiation

    Directory of Open Access Journals (Sweden)

    S. Pramanik

    2014-03-01

    Full Text Available The present paper aims at investigating the boundary layer flow of a non-Newtonian fluid accompanied by heat transfer toward an exponentially stretching surface in presence of suction or blowing at the surface. Casson fluid model is used to characterize the non-Newtonian fluid behavior. Thermal radiation term is incorporated into the equation for the temperature field. With the help of similarity transformations, the governing partial differential equations corresponding to the momentum and heat transfer are reduced to a set of non-linear ordinary differential equations. Numerical solutions of these equations are then obtained. The effect of increasing values of the Casson parameter is seen to suppress the velocity field. But the temperature is enhanced with increasing Casson parameter. Thermal radiation enhances the effective thermal diffusivity and the temperature increases. It is found that the skin-friction coefficient increases with the increase in suction parameter.

  4. Experimental study of the surface thermal signature of gravity currents: application to the assessment of lava flow effusion rate

    Science.gov (United States)

    Garel, F.; Kaminski, E.; Tait, S.; Limare, A.

    2011-12-01

    During an effusive volcanic eruption, the crisis management is mainly based on the prediction of lava flows advance and its velocity. As the spreading of lava flows is mainly controlled by its rheology and the eruptive mass flux, the key question is how to evaluate them during the eruption (rather than afterwards.) A relationship between the heat flux lost by the lava at its surface and the eruption rate is likely to exist, based on the first-order argument that higher eruption rates should correspond to larger power radiated by a lava flow. The semi-empirical formula developed by Harris and co-workers (e.g. Harris et al., Bull. Volc. 2007) is currently used to estimate lava flow rate from satellite surveys yielding the surface temperatures and area of the lava flow field. However, this approach is derived from a static thermal budget of the lava flow and does not explicitly model the time-evolution of the surface thermal signal. Here we propose laboratory experiments and theoretical studies of the cooling of a viscous axisymmetric gravity current fed at constant flux rate. We first consider the isoviscous case, for which the spreading is well-know. The experiments using silicon oil and the theoretical model both reveal the establishment of a steady surface thermal structure after a transient time. The steady state is a balance between surface cooling and heat advection in the flow. The radiated heat flux in the steady regime, a few days for a basaltic lava flow, depends mainly on the effusion rate rather than on the viscosity. In this regime, one thermal survey of the radiated power could provide a consistent estimate of the flow rate if the external cooling conditions (wind) are reasonably well constrained. We continue to investigate the relationship between the thermal radiated heat flux and the effusion rate by using in the experiments fluids with temperature-dependent viscosity (glucose syrup) or undergoing solidification while cooling (PEG wax). We observe a

  5. Influence of thermal annealing on microstructural, morphological, optical properties and surface electronic structure of copper oxide thin films

    Energy Technology Data Exchange (ETDEWEB)

    Akgul, Funda Aksoy, E-mail: fundaaksoy01@gmail.com [Department of Physics, Nigde University, 51240 Nigde (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey); Akgul, Guvenc, E-mail: guvencakgul@gmail.com [Bor Vocational School, Nigde University, 51700 Nigde (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey); Yildirim, Nurcan [Department of Physics Engineering, Ankara University, 06100 Ankara (Turkey); Department of Metallurgical and Materials Engineering, Middle East Technical University, 06800 Ankara (Turkey); Unalan, Husnu Emrah [Department of Metallurgical and Materials Engineering, Middle East Technical University, 06800 Ankara (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey); Turan, Rasit [Department of Physics, Middle East Technical University, 06800 Ankara (Turkey); Center for Solar Energy Research and Applications, Middle East Technical University, 06800 Ankara (Turkey)

    2014-10-15

    In this study, effect of the post-deposition thermal annealing on copper oxide thin films has been systemically investigated. The copper oxide thin films were chemically deposited on glass substrates by spin-coating. Samples were annealed in air at atmospheric pressure and at different temperatures ranging from 200 to 600°C. The microstructural, morphological, optical properties and surface electronic structure of the thin films have been studied by diagnostic techniques such as X-ray diffraction (XRD), Raman spectroscopy, ultraviolet–visible (UV–VIS) absorption spectroscopy, field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The thickness of the films was about 520 nm. Crystallinity and grain size was found to improve with annealing temperature. The optical bandgap of the samples was found to be in between 1.93 and 2.08 eV. Cupric oxide (CuO), cuprous oxide (Cu{sub 2}O) and copper hydroxide (Cu(OH){sub 2}) phases were observed on the surface of as-deposited and 600 °C annealed thin films and relative concentrations of these three phases were found to depend on annealing temperature. A complete characterization reported herein allowed us to better understand the surface properties of copper oxide thin films which could then be used as active layers in optoelectronic devices such as solar cells and photodetectors. - Highlights: • Effect of post-deposition annealing on copper oxide thin films was investigated. • Structural, optical, and electronic properties of the thin films were determined. • Oxidation states of copper oxide thin films were confirmed by XPS analysis. • Mixed phases of CuO and Cu{sub 2}O were found to coexist in copper oxide thin films.

  6. Surface properties of pillared acid-activated bentonite as catalyst for selective production of linear alkylbenzene

    Science.gov (United States)

    Faghihian, Hossein; Mohammadi, Mohammad Hadi

    2013-01-01

    Acid-activated and pillared montmorillonite were prepared as novel catalysts for alkylation of benzene with 1-decene for production of linear alkylbenzene. The catalysts were characterized by X-ray diffraction, FT-IR spectroscopy, N2 adsorption isotherms, temperature programmed desorption of NH3, scanning electron microscopy and elemental and thermal analysis techniques. It was found that acid-activation of clays prior to pillaring increased the porosity, total specific surface area, total pore volume and surface acidity of the catalysts. Optimization of the reaction conditions was performed by varying catalyst concentration (0.25-1.75 wt%), reactants ratio (benzene to 1-decene of 8.75, 12 and 15) and temperature (115-145 °C) in a batch slurry reactor. Under optimized conditions more than 98% conversion of 1-decene, and complete selectivity for monoalkylbenzenes were achieved.

  7. Sensitivity analysis of radiative transfer for atmospheric remote sensing in thermal IR: atmospheric weighting functions and surface partials

    Science.gov (United States)

    Ustinov, E. A.

    2003-01-01

    In this presentation, we apply the adjoint sensitivity analysis of radiative transfer in thermal IR to the general case of the analytic evaluation of the weighting functions of atmospheric parameters together with the partial derivatives for the surface parameters. Applications to remote sensing of atmospheres of Mars and Venus are discussed.

  8. Role of nanoclay shape and surface characteristics on the morphology and thermal properties of polystyrene nanocomposites synthesized via emulsion polymerization

    CSIR Research Space (South Africa)

    Greesh, N

    2013-10-01

    Full Text Available This work evaluates the role of the surface properties and shape of clay type on the morphology, thermal, and thermo-mechanical properties of the polystyrene (PS)/clay nanocomposites prepared via free-radical emulsion polymerization. Attapulgite...

  9. Collisionally-activated dissociation in hyperthermal surface ionization of cholesterol

    Science.gov (United States)

    Dagan, Shai; Danon, Albert; Amirav, Aviv

    1992-03-01

    Cholesterol in a hydrogen-seeded supersonic molecular beam was scattered from a continuously oxidized rhenium foil. The hyperthermal surface scattering exhibited efficient molecular ionization with a controlled amount of molecular ion dissociation. At 5.3 eV incident molecular kinetic energy the hyperthermal surface ionization mass spectrum was dominated by the parent molecular ion. Upon the increase of the molecular kinetic energy, a gradual increase in the degree of ion dissociation was observed. At 22eV incident kinetic energy the parent ion was completely dissociated and the mass spectrum was dominated by an extensive consecutive fragmentation. An efficient kinetic-vibrational energy transfer was observed, and it is extimated to be over 18% of the available incident kinetic energy. The implication for surface collisionally-activated dissociation of polyatomic ions is discussed. Rhenium oxide is suggested as an optimal surface for this purpose, as well as for the hyperthermal surface ionization of neutral species.

  10. The Surface Groups and Active Site of Fibrous Mineral Materials

    Institute of Scientific and Technical Information of China (English)

    DONG Fa-qin; WAN Pu; FENG Qi-ming; SONG Gong-bao; PENG Tong-jiang; LI Ping; LI Guo-wu

    2004-01-01

    The exposed and transformed groups of fibrous brucite,wollastonite,chrysotile asbestos,sepiolite,palygorskite,clinoptilolite,crocidolite and diatomaceous earth mineral materials are analyzed by IR spectra after acid and alikali etching,strong mechanical and polarity molecular interaction.The results show the active sites concentrate on the ends in stick mineral materials and on the defect or hole edge in pipe mineral materials.The inside active site of mineral materials plays a main role in small molecular substance.The shape of minerals influence their distribution and density of active site.The strong mechanical impulsion and weak chemical force change the active site feature of minerals,the powder process enables minerals exposed more surface group and more combined types.The surface processing with the small polarity molecular or the brand of middle molecular may produce ionation and new coordinate bond,and change the active properties and level of original mineral materials.

  11. Response surface optimisation for activation of bentonite with microwave irradiation

    Directory of Open Access Journals (Sweden)

    Rožić Ljiljana S.

    2011-01-01

    Full Text Available In this study, the statistical design of the experimental method was applied on the acid activation process of bentonite with microwave irradiation. The influence of activation parameters (time, acid normality and microwave heating power on the selected process response of the activated bentonite samples was studied. The specific surface area was chosen for the process response, because