WorldWideScience

Sample records for surface poisoning processes

  1. Rejuvenation processes applied to 'poisoned' anion exchangers in uranium processing

    International Nuclear Information System (INIS)

    Gilmore, A.J.

    1979-11-01

    The removal of 'poisons' from anion exchangers in uranium processing of Canadian radioactive ores is commonly called rejuvenation or regeneration. The cost of the ion exchange recovery of uranium is adversely affected by a decrease in the capacity and efficiency of the anion exchangers, due to their being 'poisoned' by silica, elemental sulphur, molybdenum and tetrathionates. These 'poisons' have a high affinity for the anion exchangers, are adsorbed in preference to the uranyl complex, and do not desorb with the reagents used normally in the uranyl desorption phase. The frequency of rejuvenation and the reagents required for rejuvenation are determined by the severity of the 'poisoning' accumulated by the exchanger in contact with the uranium leach liquor. Caustic soda (NaOH) at approximately equal to 18 cents/lb is commonly used to remove uranium anion exchangers of tetrathionate ((S 4 0 6 )/-/-) 'poisons'. A potential saving in operating cost would be of consequence if other reagents, e.g. sodium carbonate (Na 2 CO 3 ) at approximately equal to 3.6 cents/lb or calcium hydroxide (Ca(OH) 2 ) at approximately equal to 1.9 cents/lb, were effective in removing (S 4 0 6 )/-/-) from a 'poisoned' exchanger. A rejuvenation process for a test program was adopted after a perusal of the literature

  2. Poisoning

    Science.gov (United States)

    ... your home. Regularly test and replace the batteries. Poisoning treatment Treatment depends on the person and the type ... Injury Prevention, Prevention and Wellness, Staying HealthyTags: chemical ... poison treatments, snakebite, syrup of ipecac July 12, 2017 Featured ...

  3. Processing of poison rods with a view to disposal

    International Nuclear Information System (INIS)

    Bichet, R.; Charamathieu, A.; Lasseur, C.; Golicheff, I.; Pouteaux, M.

    1979-01-01

    In the core of the French 900 and 1300 MW reactors, a certain number of rods have to be processed as wastes, particularly the burnable poison rods used during reactor start-up (900 MW: 68 rods; 1300 MW: 96 rods). Several solutions are possible: cutting and conditionning in reactor pool; transfer of the poison rods to a cutting and conditionning facility; transfer of the poison rods and fuel assemblies to a storage area where they are cutted and stored. Each of these solutions are studied, the advantages and disadvantages being presented

  4. Evaluation of processed borax as antidote for aconite poisoning.

    Science.gov (United States)

    Sarkar, Prasanta Kumar; Prajapati, Pradeep K; Shukla, Vinay J; Ravishankar, Basavaiah

    2017-06-09

    Aconite root is very poisonous; causes cardiac arrhythmias, ventricular fibrillation and ventricular tachycardia. There is no specific antidote for aconite poisoning. In Ayurveda, dehydrated borax is mentioned for management of aconite poisoning. The investigation evaluated antidotal effect of processed borax against acute and sub-acute toxicity, cardiac toxicity and neuro-muscular toxicity caused by raw aconite. For acute protection Study, single dose of toxicant (35mg/kg) and test drug (22.5mg/kg and 112.5mg/kg) was administered orally, and then 24h survival of animals was observed. The schedule was continued for 30 days in sub-acute protection Study with daily doses of toxicant (6.25mg/kg), test drug (22.5mg/kg and 112.5mg/kg) and vehicle. Hematological and biochemical tests of blood and serum, histopathology of vital organs were carried out. The cardiac activity Study was continued for 30 days with daily doses of toxicant (6.25mg/kg), test drug (22.5mg/kg), processed borax solution (22.5mg/kg) and vehicle; ECG was taken after 1h of drug administration on 1 TB , 15th and on 30th day. For neuro-muscular activity Study, the leech dorsal muscle response to 2.5µg of acetylcholine followed by response of toxicant at 25µg and 50µg doses and then response of test drug at 25µg dose were recorded. Protection index indicates that treated borax gave protection to 50% rats exposed to the lethal dose of toxicant in acute protection Study. Most of the changes in hematological, biochemical parameters and histopathological Study induced by the toxicant in sub-acute protection Study were reversed significantly by the test drug treatment. The ventricular premature beat and ventricular tachyarrhythmia caused by the toxicant were reversed by the test drug indicate reversal of toxicant induced cardio-toxicity. The acetylcholine induced contractions in leech muscle were inhibited by toxicant and it was reversed by test drug treatment. The processed borax solution is found as an

  5. A consolidation process for spent burnable poison rod assemblies

    International Nuclear Information System (INIS)

    Yamamoto, Y.; Harada, M.; Komatsu, Y.

    1985-01-01

    A new consolidation system for the spent burnable poison assembly utilizing a sequence control robot operated under water was proposed. A credible accident in the system was analyzed mainly from the viewpoint of tritium release, based on the diffusion analysis of tritium in borosilicate glass. It was found that the amount of tritium released would be small even after the rupture of burnable poison rods. An experiment on a new consolidation system was performed using spent burnable poison assemblies. The volume of burnable poison assemblies was reduced safely and securely by a factor of 7 to 14 for burnable poison rods and by 22 for hold-down portions. It was proved that the consolidation system is collectively feasible

  6. The manufacture process and properties of (U, Gd)O2 burnable poisonous fuel pellets

    International Nuclear Information System (INIS)

    Yi Wei; Tang Yueming; Dai Shengping; Yang Youqing; Zuo Guoping; Wu Shihong; Gu Xiaofei; Gu Mingfei

    2006-03-01

    The main properties of important raw powder materials used in the (U, Gd)O 2 burnable poisonous fuel pellets production line of NPIC are presented. The powders included UO 2 , Gd 2 O 3 , (U, Gd) 3 O 8 and necessary additives, such as ammonium oxalate and zinc stearate. And the main properties of (U, Gd)O 2 burnable poisonous fuel pellets and the manufacture processes, such as ball-milling blending, granulation, pressing, sintering and grinding are also described. Moreover, the main effect of the process parameters controlled in the manufacture process have been discussed. (authors)

  7. Mercurial poisoning

    Energy Technology Data Exchange (ETDEWEB)

    Gorton, B

    1924-01-01

    Cats which had been kept in a thermometer factory to catch rats were afflicted with mercury poisoning. So were the rats they were supposed to eat. The symptoms of mercury poisoning were the same in both species. The source of mercury for these animals is a fine film of the metal which coats floors, a result of accidental spills during the manufacturing process.

  8. Permanganate oxidation of sulfur compounds to prevent poisoning of Pd catalysts in water treatment processes.

    Science.gov (United States)

    Angeles-Wedler, Dalia; Mackenzie, Katrin; Kopinke, Frank-Dieter

    2008-08-01

    The practical application of Pd-catalyzed water treatment processes is impeded by catalyst poisoning by reduced sulfur compounds (RSCs). In this study, the potential of permanganate as a selective oxidant for the removal of microbially generated RSCs in water and as a regeneration agent for S-poisoned catalysts was evaluated. Hydrodechlorination using Pd/Al2O3 was carried out as a probe reaction in permanganate-pretreated water. The activity of the Pd catalysts in the successfully pretreated reaction medium was similar to that in deionized water. The catalyst showed no deactivation behavior in the presence of permanganate at a concentration level or = 0.08 mM, a significant but temporary inhibition of the catalytic dechlorination was observed. Unprotected Pd/Al2O3, which had been completely poisoned by sulfide, was reactivated by a combined treatment with permanganate and hydrazine. However, the anthropogenic water pollutants thiophene and carbon disulfide were resistant against permanganate. Together with the preoxidation of catalyst poisons, hydrophobic protection of the catalysts was studied. Pd/zeolite and various hydrophobically coated catalysts showed a higher stability against ionic poisons and permanganate than the uncoated catalyst. By means of a combination of oxidative water pretreatment and hydrophobic catalyst protection, we provide a new tool to harness the potential of Pd-catalyzed hydrodehalogenation for the treatment of real waters.

  9. Process for the manufacture of plates containing neutron poison from aluminium and aluminium alloys

    International Nuclear Information System (INIS)

    Bauer, G.; Pollmann, E.; Srostlik, P.

    1985-01-01

    A process for guaranteeing sub-critical arrangements of nuclear fuel in tranport and/or storage containers is described, in which a homogeneous distribution of neutron poison in the aluminium matrix is guaranteed. A homogeneous mixture of aluminium powder and neutron poison powder is produced, this is pressed into plates in several stages, dried and made into hollow aluminium profiles of rectangular cross-section. The open ends of the hollow profile are then closed and this is rolled to the required dimension at 470-500 0 C. (orig./HP) [de

  10. Nuclear fuel clad clothed with burnable poison and obtainment process

    International Nuclear Information System (INIS)

    Diez, P.; Netter, P.

    1994-01-01

    This clad has preferentially on its inner surface a boron compound such boron carbide or boron nitrogen deposited by Chemical Vapor Deposition or by Physical Vapor Deposition without any temperature elevation injurious to its mechanical properties. 3 figs

  11. Ciguatera fish poisoning and sea surface temperatures in the Caribbean Sea and the West Indies.

    Science.gov (United States)

    Tester, Patricia A; Feldman, Rebecca L; Nau, Amy W; Kibler, Steven R; Wayne Litaker, R

    2010-10-01

    Ciguatera fish poisoning (CFP) is a circumtropical disease caused by ingestion of a variety of reef fish that bioaccumulate algal toxins. Distribution and abundance of the organisms that produce these toxins, chiefly dinoflagellates of the genus Gambierdiscus, are reported to correlate positively with water temperature. Consequently, there is growing concern that increasing temperatures associated with climate change could increase the incidence of CFP. This concern prompted experiments on the growth rates of six Gambierdiscus species at temperatures between 18 degrees C and 33 degrees C and the examination of sea surface temperatures in the Caribbean and West Indies for areas that could sustain rapid Gambierdiscus growth rates year-round. The thermal optimum for five of six Gambierdiscus species tested was >/=29 degrees C. Long-term SST data from the southern Gulf of Mexico indicate the number of days with sea surface temperatures >/=29 degrees C has nearly doubled (44 to 86) in the last three decades. To determine how the sea surface temperatures and Gambierdiscus growth data correlate with CFP incidences in the Caribbean, a literature review and a uniform, region-wide survey (1996-2006) of CFP cases were conducted. The highest CFP incidence rates were in the eastern Caribbean where water temperatures are warmest and least variable. Published by Elsevier Ltd.

  12. Canning process that diminishes paralytic shellfish poison in naturally contaminated mussels (Mytilus galloprovincialis).

    Science.gov (United States)

    Vieites, J M; Botana, L M; Vieytes, M R; Leira, F J

    1999-05-01

    Changes in toxin profile and total toxicity levels of paralytic shellfish poison (PSP)-containing mussels were monitored during the standard canning process of pickled mussels and mussels in brine using mouse bioassays and high-performance liquid chromatography. Detoxification percentages for canned mussel meat exceeded 50% of initial toxicity. Total toxicity reduction did not fully correspond to toxin destruction, which was due to the loss of PSP to cooking water and packing media of the canned product. Significant differences in detoxification percentages were due to changes in toxin profile during heat treatment in packing media. Toxin conversion phenomena should be determined to validate detoxification procedures in the canning industry.

  13. Effect of Cu Alloying on S Poisoning of Ni Surfaces and Nanoparticle Morphologies Using Ab-Initio Thermodynamics Calculations.

    Science.gov (United States)

    Kim, Ji-Su; Kim, Byung-Kook; Kim, Yeong-Cheol

    2015-10-01

    We investigated the effect of Cu alloying on S poisoning of Ni surfaces and nanoparticle morphologies using ab-initio thermodynamics calculations. Based on the Cu segregation energy and the S adsorption energy, the surface energy and nanoparticle morphology of pure Ni, pure Cu, and NiCu alloys were evaluated as functions of the chemical potential of S and the surface orientations of (100), (110), and (111). The constructed nanoparticle morphology was varied as a function of chemical potential of S. We find that the Cu added to Ni for NiCu alloys is strongly segregated into the top surface, and increases the S tolerance of the NiCu nanoparticles.

  14. Effect of cytokine treatment on the neurogenesis process in the brain of soman-poisoned mice

    International Nuclear Information System (INIS)

    Collombet, Jean-Marc; Four, Elise; Burckhart, Marie-France; Masqueliez, Catherine; Bernabe, Denis; Baubichon, Dominique; Herodin, Francis; Lallement, Guy

    2005-01-01

    We previously described that enhanced proliferation of neural progenitors occurred in the subgranular zone (SGZ) of the dentate gyrus and in the subventricular zone (SVZ) of the mouse brain following soman poisoning. Then, a discrete number of these cells seemed to migrate and engraft into the main damaged brain regions (hippocampus; septum and amygdala) and subsequently differentiate into neurons. In the present study, the effect of a cytokine treatment on the neurogenesis process was evaluated. For this purpose, subcutaneous injection of a cocktail of 40 μg/kg epidermal growth factor (EGF) and basic fibroblast growth factor (bFGF) was administered daily to soman-poisoned mice (110 μg/kg soman and 5.0 mg/kg methyl nitrate atropine), from post-soman days 1 to 8. To label replicating neural progenitors, 200 mg/kg bromodeoxyuridine (BrdU) was injected twice a day between post-soman days 6 and 8. Mice were sacrificed on post-soman day 9 or 34. On post-soman day 9, the cytokine treatment had no effect on the proliferation of neural progenitors in the SVZ and SGZ, as assessed by BrdU immunochemistry. However, this treatment seemed to promote the migration of neural precursor cells from the proliferative areas towards damaged brain regions. Indeed, in the CA1 hippocampal layer of soman-poisoned mice, on post-soman day 34, the cytokine treatment increased the number of healthy pyramidal neurons stained by hemalun-eosin dye. The cytokine treatment also augmented the number of BrdU-labeled cells in the CA1 hippocampal layer and amygdala. Interestingly, the administration of cytokines resulted in the differentiation of BrdU-positive cells into new neurons in the CA1 hippocampal layer, whereas astrocytic differentiation was preferentially observed in the amygdala

  15. Dieffenbachia poisoning

    Science.gov (United States)

    Dumbcane poisoning; Leopard lily poisoning; Tuft root poisoning ... Get the following information: Person's age, weight, and condition Parts of the plant that were eaten, if known Time swallowed Amount swallowed

  16. Mistletoe poisoning

    Science.gov (United States)

    ... if known Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  17. Detergent poisoning

    Science.gov (United States)

    ... if known) Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  18. Kerosene poisoning

    Science.gov (United States)

    ... if known) Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  19. Zinc poisoning

    Science.gov (United States)

    ... help if this information is not immediately available. Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  20. Foxglove poisoning

    Science.gov (United States)

    ... if known Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  1. Cologne poisoning

    Science.gov (United States)

    ... the product Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  2. Bee poison

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/002847.htm Bee poison To use the sharing features on this page, ... Time of the sting Location of the sting Poison Control Your local poison center can be reached ...

  3. Oleander poisoning

    Science.gov (United States)

    ... if known Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  4. Insecticide poisoning

    Science.gov (United States)

    ... if known) Time it was swallowed Amount swallowed Poison Control Your local poison control center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  5. Ammonia poisoning

    Science.gov (United States)

    ... if known) Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  6. Yew poisoning

    Science.gov (United States)

    ... if known Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  7. Philodendron poisoning

    Science.gov (United States)

    ... if known Time it was swallowed Amount swallowed Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  8. Poison Ivy Dermatitis

    Science.gov (United States)

    ... than the other two. Poison ivy clings to tree trunks and other vertical surfaces with hair-like ... urushiol". These are called Rhus plants after the old scientific name (it was changed to toxidendron). A ...

  9. Superhydrophobic surfaces by electrochemical processes.

    Science.gov (United States)

    Darmanin, Thierry; Taffin de Givenchy, Elisabeth; Amigoni, Sonia; Guittard, Frederic

    2013-03-13

    This review is an exhaustive representation of the electrochemical processes reported in the literature to produce superhydrophobic surfaces. Due to the intensive demand in the elaboration of superhydrophobic materials using low-cost, reproducible and fast methods, the use of strategies based on electrochemical processes have exponentially grown these last five years. These strategies are separated in two parts: the oxidation processes, such as oxidation of metals in solution, the anodization of metals or the electrodeposition of conducting polymers, and the reduction processed such as the electrodeposition of metals or the galvanic deposition. One of the main advantages of the electrochemical processes is the relative easiness to produce various surface morphologies and a precise control of the structures at a micro- or a nanoscale. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Merthiolate poisoning

    Science.gov (United States)

    Merthiolate poisoning is difficult to treat. How well a person does depends on the amount of poison swallowed and how quickly treatment was received. The faster a person gets medical help, the better the chance for recovery. Kidney dialysis ( ...

  11. Benzene poisoning

    Science.gov (United States)

    ... may be admitted to the hospital if the poisoning is severe. ... benzene they swallowed and how quickly they receive treatment. The ... Poisoning can cause rapid death. However, deaths have occurred ...

  12. Malathion poisoning

    Science.gov (United States)

    ... Prolonged treatment often is needed to reverse the poisoning. This may include staying in the hospital intensive care unit and getting long-term therapy. Some effects of the poison may last for ...

  13. Diazinon poisoning

    Science.gov (United States)

    ... Prolonged treatment often is needed to reverse the poisoning. This may include staying in the hospital intensive care unit and getting long-term therapy. Some effects of the poison may last for ...

  14. Effect of Na poisoning catalyst (V2O5-WO3/TiO2) on denitration process and SO3 formation

    Science.gov (United States)

    Xiao, Haiping; Chen, Yu; Qi, Cong; Ru, Yu

    2018-03-01

    This paper aims to study the effect of alkali metal sodium (Na) poisoning on the performance of the Selective Catalytic Reduction (SCR) catalyst. The result showed that Na2SO4 poisoning leads to a reduced denitration rate of the SCR catalyst and an increase in the SO3 generation rate. Na2O poisoning leads to a significant reduction in the denitration rate of the SCR catalyst and marginally improves the formation of SO3. The maximum of the SO3 generation rate for a Na2SO4-poisoned catalyst reached 1.35%, whereas it was only 0.85% for the SCR catalyst. When the SO2 was contained in flue gas, the denitration rate for the Na2O-poisoned catalyst clearly increased by more than 28%. However, the effect of SO2 on the Na2SO4-poisoned catalyst was very slight. The denitration rate of the SCR catalyst decreased with an increase in the Na content. The BET and XRD results showed that Na poisoning of the catalyst decreased the number of acid sites, the reducibility of the catalyst, the surface area, and pore volume. The H2-TPR and NH3-TPD results show that Na decreases the number of acid sites and the reducibility of the catalyst. The FT-IR and XPS results showed that Na2O poisoning led to the decrease of V5+dbnd O bonds and the consumptions of oxygen atoms. Na2SO4 poisoning can improve surface adsorbed oxygen, which was beneficial for the SO2-SO3 conversion reaction.

  15. Nanoscale processes on insulating surfaces

    National Research Council Canada - National Science Library

    Gnecco, Enrico; Szymoński, Marek

    2009-01-01

    ... the group of Prof. Ernst Meyer in Basel, where he investigated friction processes on alkali halide surfaces in ultra high vacuum (UHV). The main result was the observation of a logarithmic velocity dependence of atomic friction, which was interpreted within a combination of the classical Tomlinson and Eyring models. After his Ph.D. he joined the ...

  16. Surface poisoning in the nucleation and growth of palladium atomic layer deposition with Pd(hfac){sub 2} and formalin

    Energy Technology Data Exchange (ETDEWEB)

    Goldstein, D.N. [Department of Chemistry and Biochemistry, University of Colorado, 215 UCB, Boulder, CO 80309 (United States); George, S.M., E-mail: Steven.George@Colorado.Edu [Department of Chemistry and Biochemistry, University of Colorado, 215 UCB, Boulder, CO 80309 (United States); Department of Chemical and Biological Engineering, University of Colorado, 424 UCB, Boulder, CO (United States)

    2011-06-01

    Palladium (Pd) atomic layer deposition (ALD) can be performed with Pd(hfac){sub 2} (hfac = hexafluoroacetyl-acetone) and formalin as the reactants. For Pd ALD on oxide surfaces, the nucleation of Pd ALD has been observed to require between 20 and 100 ALD cycles. To understand the long nucleation periods, this study explored the surface reactions occurring during Pd ALD nucleation and growth on hydroxylated Al{sub 2}O{sub 3} substrates. In situ Fourier transform infrared (FTIR) spectroscopy on high surface area nanopowders was used to observe the surface species. The adsorption of Pd(hfac){sub 2} on hydroxylated Al{sub 2}O{sub 3} substrates was found to yield both Pd(hfac)* and Al(hfac)* surface species. The identity of the Al(hfac)* species was confirmed by separate FTIR studies of hfacH adsorption on the hydroxylated Al{sub 2}O{sub 3} substrates. Isothermal loss of the Al(hfac)* species revealed second-order kinetics at 448-523 K with an activation barrier of E{sub d} = 39.4 kcal/mol. The lack of correlation between Al(hfac)* and AlOH* species during the loss of Al(hfac)* species suggested that the Al(hfac)* species may desorb as Al(hfac){sub 3}. After Pd(hfac){sub 2} exposure and the subsequent formalin exposure on hydroxylated Al{sub 2}O{sub 3} substrates, only hfac ligands from Pd(hfac)* species were removed from the surface. In addition, the formalin exposure added formate species. The Al(hfac)* species was identified as the cause of the long nucleation period because Al(hfac)* behaves as a site blocker. The surface poisoning by Al(hfac)* species was corroborated by adsorbing hfacH prior to the Pd(hfac){sub 2} exposures. The amount of Pd(hfac)* species after Pd(hfac){sub 2} exposures decreased progressively versus the previous hfacH exposure. Pd ALD occurred gradually during the subsequent Pd ALD cycles as the Al(hfac)* species were slowly removed from the Al{sub 2}O{sub 3} surface. Ex situ transmission electron microscopy analysis revealed Pd nanoclusters

  17. Śodhana: An Ayurvedic process for detoxification and modification of therapeutic activities of poisonous medicinal plants

    Directory of Open Access Journals (Sweden)

    Santosh Kumar Maurya

    2015-01-01

    Full Text Available Ayurveda involves the use of drugs obtained from plants, animals, and mineral origin. All the three sources of drugs can be divided under poisonous and nonpoisonous category. There are various crude drugs, which generally possess unwanted impurities and toxic substances, which can lead to harmful health problems. Many authors have reported that not all medicinal plants are safe to use since they can bear many toxic and harmful phytoconstituents in them. Śodhana (detoxification/purification is the process, which involves the conversion of any poisonous drug into beneficial, nonpoisonous/nontoxic ones. Vatsanābha (Aconitum species, Semecarpus anacardium, Strychnos nux-vomica, Acorus calamus, Abrus precatorius etc., are some of the interesting examples of toxic plants, which are still used in the Indian system of medicine. Aconite, bhilawanols, strychnine, β-asarone, abrin are some of the toxic components present in these plants and are relatively toxic in nature. Śodhana process involves the purification as well as reduction in the levels of toxic principles which sometimes results in an enhanced therapeutic efficacy. The present review is designed to extensively discuss and understand the scientific basis of the alternative use of toxic plants as a medicine after their purification process.

  18. Śodhana: An Ayurvedic process for detoxification and modification of therapeutic activities of poisonous medicinal plants

    Science.gov (United States)

    Maurya, Santosh Kumar; Seth, Ankit; Laloo, Damiki; Singh, Narendra Kumar; Gautam, Dev Nath Singh; Singh, Anil Kumar

    2015-01-01

    Ayurveda involves the use of drugs obtained from plants, animals, and mineral origin. All the three sources of drugs can be divided under poisonous and nonpoisonous category. There are various crude drugs, which generally possess unwanted impurities and toxic substances, which can lead to harmful health problems. Many authors have reported that not all medicinal plants are safe to use since they can bear many toxic and harmful phytoconstituents in them. Śodhana (detoxification/purification) is the process, which involves the conversion of any poisonous drug into beneficial, nonpoisonous/nontoxic ones. Vatsanābha (Aconitum species), Semecarpus anacardium, Strychnos nux-vomica, Acorus calamus, Abrus precatorius etc., are some of the interesting examples of toxic plants, which are still used in the Indian system of medicine. Aconite, bhilawanols, strychnine, β–asarone, abrin are some of the toxic components present in these plants and are relatively toxic in nature. Śodhana process involves the purification as well as reduction in the levels of toxic principles which sometimes results in an enhanced therapeutic efficacy. The present review is designed to extensively discuss and understand the scientific basis of the alternative use of toxic plants as a medicine after their purification process. PMID:26283803

  19. Beryllium poisonings

    International Nuclear Information System (INIS)

    Alibert, S.

    1959-03-01

    This note reports a bibliographical study of beryllium toxicity. Thus, this bibliographical review addresses and outlines aspects and issues like aetiology, cases of acute poisoning (cutaneous manifestations, pulmonary manifestations), chronic poisoning (cutaneous, pulmonary and bone manifestations), excretion and localisation, and prognosis

  20. Understanding the effect of steps, strain, poisons, and alloying: Methane activation on Ni surfaces

    DEFF Research Database (Denmark)

    Abild-Pedersen, Frank; Greeley, Jeffrey Philip; Nørskov, Jens Kehlet

    2005-01-01

    It is shown that a single parameter characterizing the electronic structure of a transition metal surface, the d-band center (epsilon(d)), can be used to provide a unified description of a range of phenomena in heterogeneous catalysis. Using methane activation on Ni surfaces as an example, we show...

  1. Childhood Lead Poisoning Associated with Gold Ore Processing: a Village-Level Investigation—Zamfara State, Nigeria, October–November 2010

    Science.gov (United States)

    Lo, Yi-Chun; Dooyema, Carrie A.; Neri, Antonio; Durant, James; Jefferies, Taran; Medina-Marino, Andrew; de Ravello, Lori; Thoroughman, Douglas; Davis, Lora; Dankoli, Raymond S.; Samson, Matthias Y.; Ibrahim, Luka M.; Okechukwu, Ossai; Umar-Tsafe, Nasir T.; Dama, Alhassan H.

    2012-01-01

    Background: During May–June 2010, a childhood lead poisoning outbreak related to gold ore processing was confirmed in two villages in Zamfara State, Nigeria. During June–September of that year, villages with suspected or confirmed childhood lead poisoning continued to be identified in Zamfara State. Objectives: We investigated the extent of childhood lead poisoning [≥ 1 child with a blood lead level (BLL) ≥ 10 µg/dL] and lead contamination (≥ 1 soil/dust sample with a lead level > 400 parts per million) among villages in Zamfara State and identified villages that should be prioritized for urgent interventions. Methods: We used chain-referral sampling to identify villages of interest, defined as villages suspected of participation in gold ore processing during the previous 12 months. We interviewed villagers, determined BLLs among children lead. Results: We identified 131 villages of interest and visited 74 (56%) villages in three local government areas. Fifty-four (77%) of 70 villages that completed the survey reported gold ore processing. Ore-processing villages were more likely to have ≥ 1 child lead poisoning (68% vs. 50%, p = 0.17) or death following convulsions (74% vs. 44%, p = 0.02). Soil/dust contamination and BLL ≥ 45 µg/dL were identified in ore-processing villages only [50% (p lead poisoning or lead contamination was 3.5 times as high in ore-processing villages than the other villages (95% confidence interval: 1.1, 11.3). Conclusion: Childhood lead poisoning and lead contamination were widespread in surveyed areas, particularly among villages that had processed ore recently. Urgent interventions are required to reduce lead exposure, morbidity, and mortality in affected communities. PMID:22766030

  2. Gasoline poisoning

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002806.htm Gasoline poisoning To use the sharing features on this ... This article discusses the harmful effects from swallowing gasoline or breathing in its fumes. This article is ...

  3. Poison Prevention

    Science.gov (United States)

    ... Safely , for more information . If you use an e-cigarette, keep the liquid nicotine refills locked up out ... to a child. See Liquid Nicotine Used in E-Cigarettes Can Kill Children . Never place poisonous products in ...

  4. Sachet poisoning

    Science.gov (United States)

    ... of perfumed powder or a mix of dried flowers, herbs, spices, and aromatic wood shavings (potpourri). Some ... further instructions. This is a free and confidential service. All local poison control centers in the United ...

  5. Deodorant poisoning

    Science.gov (United States)

    ... Poisoning and Drug Overdose . 4th ed. Philadelphia, PA: Elsevier Saunders; 2007:chap 100. Farmer B, Seger DL. ... Textbook of Critical Care . 7th ed. Philadelphia, PA: Elsevier; 2017:chap 153. Meehan TJ. Approach to the ...

  6. Acetone poisoning

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002480.htm Acetone poisoning To use the sharing features on this page, please enable JavaScript. Acetone is a chemical used in many household products. ...

  7. Surface migration in sorption processes

    International Nuclear Information System (INIS)

    Rasmuson, A.; Neretnieks, J.

    1983-03-01

    Diffusion rates of sorbing chemical species in granites and clays are in several experiments within the KBS study, higher than can be explained by pore diffusion only. One possible additional transport mechanism is transport of of sorbed molecules/ions along the intrapore surfaces. As a first step a literature investigation on on solid surfaces has been conducted. A lot of experimental evidence of the mobility of the sorbed molecules has been gathered through the years, particulary for metal surfaces and chemical engineering systems. For clays however, there are only a few articles, and for granites none. Two types of surface migration models have been proposed in the litterature: i) Surface flow as a result of a gradient in spreading pressure. ii) Surface diffusion as a result of a gradient in concentration. The surface flow model has only been applied to gaseous systems. However, it should be equally applicable to liquid systems. The models i) and ii) are conceptually very different. However, the resulting expressions for surface flux are complicated and it will not be an easy task to distinguish between them. There seem to be three ways of discriminating between the transport mechanisms: a) Temperature dependence. b) Concentration dependence. c) Order of magnitude. (Forf)

  8. Poisoning - fish and shellfish

    Science.gov (United States)

    Fish poisoning; Dinoflagellate poisoning; Seafood contamination; Paralytic shellfish poisoning; Ciguatera poisoning ... algae and algae-like organisms called dinoflagellates. Small fish that eat the algae become contaminated. If larger ...

  9. Surface studies of plasma processed Nb samples

    International Nuclear Information System (INIS)

    Tyagi, Puneet V.; Doleans, Marc; Hannah, Brian S.; Afanador, Ralph; Stewart, Stephen; Mammosser, John; Howell, Matthew P; Saunders, Jeffrey W; Degraff, Brian D; Kim, Sang-Ho

    2015-01-01

    Contaminants present at top surface of superconducting radio frequency (SRF) cavities can act as field emitters and restrict the cavity accelerating gradient. A room temperature in-situ plasma processing technology for SRF cavities aiming to clean hydrocarbons from inner surface of cavities has been recently developed at the Spallation Neutron Source (SNS). Surface studies of the plasma-processed Nb samples by Secondary ion mass spectrometry (SIMS) and Scanning Kelvin Probe (SKP) showed that the NeO_2 plasma processing is very effective to remove carbonaceous contaminants from top surface and improves the surface work function by 0.5 to 1.0 eV.

  10. Particle beam experiments for the analysis of reactive sputtering processes in metals and polymer surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Corbella, Carles; Grosse-Kreul, Simon; Kreiter, Oliver; Arcos, Teresa de los; Benedikt, Jan; Keudell, Achim von [RD Plasmas with Complex Interactions, Ruhr-Universität Bochum, Universitätsstr. 150, 44780 Bochum (Germany)

    2013-10-15

    A beam experiment is presented to study heterogeneous reactions relevant to plasma-surface interactions in reactive sputtering applications. Atom and ion sources are focused onto the sample to expose it to quantified beams of oxygen, nitrogen, hydrogen, noble gas ions, and metal vapor. The heterogeneous surface processes are monitored in situ by means of a quartz crystal microbalance and Fourier transform infrared spectroscopy. Two examples illustrate the capabilities of the particle beam setup: oxidation and nitriding of aluminum as a model of target poisoning during reactive magnetron sputtering, and plasma pre-treatment of polymers (PET, PP)

  11. Surface Modification and Surface - Subsurface Exchange Processes on Europa

    Science.gov (United States)

    Phillips, C. B.; Molaro, J.; Hand, K. P.

    2017-12-01

    The surface of Jupiter's moon Europa is modified by exogenic processes such as sputtering, gardening, radiolysis, sulfur ion implantation, and thermal processing, as well as endogenic processes including tidal shaking, mass wasting, and the effects of subsurface tectonic and perhaps cryovolcanic activity. New materials are created or deposited on the surface (radiolysis, micrometeorite impacts, sulfur ion implantation, cryovolcanic plume deposits), modified in place (thermal segregation, sintering), transported either vertically or horizontally (sputtering, gardening, mass wasting, tectonic and cryovolcanic activity), or lost from Europa completely (sputtering, plumes, larger impacts). Some of these processes vary spatially, as visible in Europa's leading-trailing hemisphere brightness asymmetry. Endogenic geologic processes also vary spatially, depending on terrain type. The surface can be classified into general landform categories that include tectonic features (ridges, bands, cracks); disrupted "chaos-type" terrain (chaos blocks, matrix, domes, pits, spots); and impact craters (simple, complex, multi-ring). The spatial distribution of these terrain types is relatively random, with some differences in apex-antiapex cratering rates and latitudinal variation in chaos vs. tectonic features. In this work, we extrapolate surface processes and rates from the top meter of the surface in conjunction with global estimates of transport and resurfacing rates. We combine near-surface modification with an estimate of surface-subsurface (and vice versa) transport rates for various geologic terrains based on an average of proposed formation mechanisms, and a spatial distribution of each landform type over Europa's surface area. Understanding the rates and mass balance for each of these processes, as well as their spatial and temporal variability, allows us to estimate surface - subsurface exchange rates over the average surface age ( 50myr) of Europa. Quantifying the timescale

  12. Lithium Poisoning

    DEFF Research Database (Denmark)

    Baird-Gunning, Jonathan; Lea-Henry, Tom; Hoegberg, Lotte C G

    2017-01-01

    Lithium is a commonly prescribed treatment for bipolar affective disorder. However, treatment is complicated by lithium's narrow therapeutic index and the influence of kidney function, both of which increase the risk of toxicity. Therefore, careful attention to dosing, monitoring, and titration...... is required. The cause of lithium poisoning influences treatment and 3 patterns are described: acute, acute-on-chronic, and chronic. Chronic poisoning is the most common etiology, is usually unintentional, and results from lithium intake exceeding elimination. This is most commonly due to impaired kidney...... function caused by volume depletion from lithium-induced nephrogenic diabetes insipidus or intercurrent illnesses and is also drug-induced. Lithium poisoning can affect multiple organs; however, the primary site of toxicity is the central nervous system and clinical manifestations vary from asymptomatic...

  13. Description of two-process surface topography

    International Nuclear Information System (INIS)

    Grabon, W; Pawlus, P

    2014-01-01

    After two machining processes, a large number of surface topography measurements were made using Talyscan 150 stylus measuring equipment. The measured samples were divided into two groups. The first group contained two-process surfaces of random nature, while the second group used random-deterministic textures of random plateau parts and portions of deterministic valleys. For comparison, one-process surfaces were also analysed. Correlation and regression analysis was used to study the dependencies among surface texture parameters in 2D and 3D systems. As the result of this study, sets of parameters describing multi-process surface topography were obtained for two-process surfaces of random and of random-deterministic types. (papers)

  14. Earth Surface Processes, Landforms and Sediment Deposits

    Science.gov (United States)

    Bridge, John; Demicco, Robert

    Earth surface processes, landforms and sediment deposits are intimately related - involving erosion of rocks, generation of sediment, and transport and deposition of sediment through various Earth surface environments. These processes, and the landforms and deposits that they generate, have a fundamental bearing on engineering, environmental and public safety issues; on recovery of economic resources; and on our understanding of Earth history. This unique textbook brings together the traditional disciplines of sedimentology and geomorphology to explain Earth surface processes, landforms and sediment deposits in a comprehensive and integrated way. It is the ideal resource for a two-semester course in sedimentology, stratigraphy, geomorphology, and Earth surface processes from the intermediate undergraduate to beginning graduate level. The book is also accompanied by a website hosting illustrations and material on field and laboratory methods for measuring, describing and analyzing Earth surface processes, landforms and sediments.

  15. Extracorporeal treatment for barbiturate poisoning

    DEFF Research Database (Denmark)

    Mactier, Robert; Laliberté, Martin; Mardini, Joelle

    2014-01-01

    The EXTRIP (Extracorporeal Treatments in Poisoning) Workgroup conducted a systematic review of barbiturate poisoning using a standardized evidence-based process to provide recommendations on the use of extracorporeal treatment (ECTR) in patients with barbiturate poisoning. The authors reviewed all...... treatment should be continued during ECTR. (4) Cessation of ECTR is indicated when clinical improvement is apparent. This report provides detailed descriptions of the rationale for all recommendations. In summary, patients with long-acting barbiturate poisoning should be treated with ECTR provided at least......-acting barbiturates are dialyzable and short-acting barbiturates are moderately dialyzable. Four key recommendations were made. (1) The use of ECTR should be restricted to cases of severe long-acting barbiturate poisoning. (2) The indications for ECTR in this setting are the presence of prolonged coma, respiratory...

  16. Plasma surface interaction processes and possible synergisms

    International Nuclear Information System (INIS)

    Behrisch, R.; Roberto, J.B.

    1984-08-01

    The process determining the plasma surface interaction in today's high temperature plasma experiments are investigated following several lines. First, in plasma devices, the particle and energy fluxes to the different first wall areas the fluxes from the walls back into the plasma are measured and the boundary plasma parameters are determined. The surface composition and structure of the walls, limiters and divertor plates are analyzed following exposure to many discharges. Secondly, the different surface processes which are expected to contribute to the plasma surface interaction (particularly to hydrogen particle balance and impurity introduction) are studied in simulation experiments using well defined particle beams

  17. Surface Energy and Setting Process of Contacting Surfaces

    Directory of Open Access Journals (Sweden)

    M. V. Musokhranov

    2014-01-01

    Full Text Available The paper deals with a challenge in terms of ensuring an accuracy of the relative position of the conjugated surfaces that is to determine a coefficient of friction. To solve it, there is a proposal to use the surface energy, as a tool that influences the contacting parts nature. Presently, energy of the surface layers at best is only stated, but not used in practice.Analysis of the conditions of interaction between two contacting surfaces, such as seizing and setting cannot be explained only from the position of the roughness parameters. It is found that these phenomena are explained by the appearing gripe (setting bridges, which result from the energy of interaction between two or more adjacent surfaces. The emerging phenomenon such as micro welding, i.e. occurring bonds, is caused by the overflow of energy, according to the theory of physics, from the surface with a high level of energy to the surface with the smaller one to balance the system as a whole.The paper shows that through the use of process, controlling the depth of the surface layer and creating a certain structure, the energy level of the material as a whole can be specified. And this will allow us to provide the necessary performance and mechanical properties. It means to create as many gripe bridges as possible to ensure continuous positioning i.e. a fixed connection of the contacting surfaces.It was determined that to increase a value of the friction coefficient, the physical and mechanical properties of the surface layer of the parts material must be taken into account, namely, in the part body accumulate the energy to be consumed for forming the surface.The paper gives recommendations for including the parts of the surface energy in the qualitative indicators of characteristics. This will make a technologist, when routing a process, to choose such operations and modes to provide the designer-specified parameters not only of the accuracy and surface finish, but also of the

  18. Poison Ivy Rash

    Science.gov (United States)

    Poison ivy rash Overview Poison ivy rash is caused by an allergic reaction to an oily resin called urushiol (u-ROO-she-ol). This oil is in the leaves, stems and roots of poison ivy, poison oak and poison sumac. Wash your ...

  19. Processing and finishing of granite surfaces

    OpenAIRE

    Klich, J. (Jiří); Hlaváček, P. (Petr); Ščučka, J. (Jiří); Sitek, L. (Libor); Foldyna, J. (Josef); Georgiovská, L. (Lucie); Souček, K. (Kamil); Staš, L. (Lubomír); Bortolussi, A.

    2013-01-01

    The article deals with granite surface processing and finishing by various methods including bush hammering, flaming, polishing, continuous and pulsating water jetting. Both optical and CT X-ray methods are used for analysis of surface and subsurface areas of tested samples. Advantages of pulsating water jetting compared to other techniques are discussed.

  20. Radon transport processes below the earth's surface

    International Nuclear Information System (INIS)

    Wilkening, M.

    1980-01-01

    Processes by which 222 Rn is transported from the soil to the earth's surface are reviewed. The mechanisms effective in transporting 222 Rn to the surface are related to the size and configuration of the spaces occupied by the soil gas which may vary from molecular interstices to large underground caverns. The near-surface transport processes are divided into two categories: (1) a microscopic process that includes molecular diffusion and viscous flow in fine capillaries and (2) macroscopic flow in fissures and channels. Underground air rich in 222 Rn can also reach the surface through cracks, fissures, and underground channels. This type of transport is shown for (1) a horizontal tunnel penetrating a fractured hillside, (2) a large underground cave, and (3) volcanic activity. Pressure differentials having various natural origins and thermal gradients are responsible for the transport in these examples. 222 Rn transport by ordinary molecular diffusion appears to be the dominant process

  1. Lead poisoning

    Energy Technology Data Exchange (ETDEWEB)

    Beijers, J A

    1952-01-01

    Three cases of acute lead poisoning of cattle herds via ingestion are reported, and reference is made to several other incidents of lead in both humans and animals. The quantity of lead which was found in the livers of the dead cows varied from 6.5 to 19 mg/kg, while 1160 mg/kg of lead in the liver was found for a young cow which was poisoned experimentally with 5 gms of lead acetate per day; hence, there appears to be great variability in the amounts deposited that can lead to intoxication and death. No evidence was found for a lead seam around the teeth, prophyrinuria, or basophil granules in the erythrocytes during acute or chronic lead poisoning of cattle or horses examined. Reference is made to attempts of finding the boundary line between increased lead absorption and lead intoxication in humans, and an examination of 60 laborers in an offset-printing office containing a great deal of inhalable lead (0.16 to 1.9 mg/cu m air) is reviewed. Physical deviation, basophylic granulation of erythrocytes, increased lead content of the urine, and porphyrinuria only indicate an increased absorption of lead; the use of the term intoxication is justified if, in addition, there are complaints of lack of appetite, constipation, fatigue, abdominal pain, and emaciation.

  2. Mechanisms and energetics of surface atomic processes

    International Nuclear Information System (INIS)

    Tsong, T.T.

    1991-01-01

    The energies involved in various surface atomic processes such as surface diffusion, the binding of small atomic clusters on the surface, the interaction between two adsorbed atoms, the dissociation of an atom from a small cluster or from a surface layer, the binding of kink size atoms or atoms at different adsorption sites to the surface etc., can be derived from an analysis of atomically resolved field ion microscope images and a kinetic energy measurement of low temperature field desorbed ions using the time-of-flight atom-probe field ion microscope. These energies can be used to compare with theories and to understand the transport of atoms on the surface in atomic reconstructions, epitaxial growth of surface layers and crystal growth, adsorption layer superstructure formation, and also why an atomic ordering or atomic reconstruction at the surface is energetically favored. Mechanisms of some of the surface atomic processes are also clarified from these quantitative, atomic resolution studies. In this paper work in this area is bris briefly reviewed

  3. Poison Control Centers

    Science.gov (United States)

    ... 1222 immediately. Name State American Association of Poison Control Centers Address AAPCC Central Office NOT A POISON ... not for emergency use. Arkansas ASPCA Animal Poison Control Center Address 1717 S. Philo Road, Suite 36 Urbana, ...

  4. Bug spray poisoning

    Science.gov (United States)

    ... was swallowed or inhaled Amount swallowed or inhaled Poison Control Your local poison center can be reached directly by calling the national toll-free Poison Help hotline (1-800-222-1222) from anywhere ...

  5. Leaching the Poison--The Importance of Process and Partnership in Working with Yolngu

    Science.gov (United States)

    Marika, Rarriwuy; Yunupingu, Yalmay; Marika-Mununggiritj, Raymattja; Muller, Samantha

    2009-01-01

    The popular construction of rural places as "white" spaces has significant repercussions for ethnic, Indigenous and "other" groups who do not always fit within prescribed dominant processes. This paper provides new insights for rural scholarship through an engagement with Indigenous specific experiences of governance and…

  6. Quantitative Modeling of Earth Surface Processes

    Science.gov (United States)

    Pelletier, Jon D.

    This textbook describes some of the most effective and straightforward quantitative techniques for modeling Earth surface processes. By emphasizing a core set of equations and solution techniques, the book presents state-of-the-art models currently employed in Earth surface process research, as well as a set of simple but practical research tools. Detailed case studies demonstrate application of the methods to a wide variety of processes including hillslope, fluvial, aeolian, glacial, tectonic, and climatic systems. Exercises at the end of each chapter begin with simple calculations and then progress to more sophisticated problems that require computer programming. All the necessary computer codes are available online at www.cambridge.org/9780521855976. Assuming some knowledge of calculus and basic programming experience, this quantitative textbook is designed for advanced geomorphology courses and as a reference book for professional researchers in Earth and planetary science looking for a quantitative approach to Earth surface processes. More details...

  7. Surface quality in rapid prototype MMD process

    Directory of Open Access Journals (Sweden)

    Lisandro Vargas Henríquez

    2004-09-01

    Full Text Available This article summarises a Manufacturing Materials and Processes MSc thesis written for the Mechanical and Electrical Engineering Department. The paper shows the interaction of process, gap (deposition distance and extursion terminal velocity modelled process parameters for CEIF's (Centro de Equipos Interfacultades rapid prototype molten material deposit (MMD Titan SH-1 machine by analysing prototupes improved surface quality and resistence to tension and characterising material. The project applies experimental design criteria for orientating the selection of experimental process parameters. Acrylonitrile-buttadin-styrene (ABS had alredy been mechanically and physicochemically characterised (i.e the material used in the MMD process.

  8. THE PRODUCT DESIGN PROCESS USING STYLISTIC SURFACES

    Directory of Open Access Journals (Sweden)

    Arkadiusz Gita

    2017-06-01

    Full Text Available The increasing consumer requirements for the way what everyday use products look like, forces manufacturers to put more emphasis on product design. Constructors, apart from the functional aspects of the parts created, are forced to pay attention to the aesthetic aspects. Software for designing A-class surfaces is very helpful in this case. Extensive quality analysis modules facilitate the work and allow getting models with specific visual features. The authors present a design process of the product using stylistic surfaces based on the front panel of the moped casing. In addition, methods of analysis of the design surface and product technology are presented.

  9. House of Poison: Poisons in the Home.

    Science.gov (United States)

    Keller, Rosanne

    One of a series of instructional materials produced by the Literacy Council of Alaska, this booklet provides information about common household poisons. Using a simplified vocabulary and shorter sentences, it provides statistics concerning accidental poisonings; a list of the places poisons are usually found in the home; steps to make the home…

  10. Extracorporeal Treatment in Phenytoin Poisoning

    DEFF Research Database (Denmark)

    Anseeuw, Kurt; Mowry, James B; Burdmann, Emmanuel A

    2016-01-01

    The Extracorporeal Treatments in Poisoning (EXTRIP) Workgroup conducted a systematic literature review using a standardized process to develop evidence-based recommendations on the use of extracorporeal treatment (ECTR) in patients with phenytoin poisoning. The authors reviewed all articles......) despite its high protein binding and made the following recommendations. ECTR would be reasonable in select cases of severe phenytoin poisoning (neutral recommendation, 3D). ECTR is suggested if prolonged coma is present or expected (graded 2D) and it would be reasonable if prolonged incapacitating ataxia...... is present or expected (graded 3D). If ECTR is used, it should be discontinued when clinical improvement is apparent (graded 1D). The preferred ECTR modality in phenytoin poisoning is intermittent hemodialysis (graded 1D), but hemoperfusion is an acceptable alternative if hemodialysis is not available...

  11. Surface analytical techniques applied to minerals processing

    International Nuclear Information System (INIS)

    Smart, R.St.C.

    1991-01-01

    An understanding of the chemical and physical forms of the chemically altered layers on the surfaces of base metal sulphides, particularly in the form of hydroxides, oxyhydroxides and oxides, and the changes that occur in them during minerals processing lies at the core of a complete description of flotation chemistry. This paper reviews the application of a variety of surface-sensitive techniques and methodologies applied to the study of surface layers on single minerals, mixed minerals, synthetic ores and real ores. Evidence from combined XPS/SAM/SEM studies have provided images and analyses of three forms of oxide, oxyhydroxide and hydroxide products on the surfaces of single sulphide minerals, mineral mixtures and complex sulphide ores. 4 refs., 2 tabs., 4 figs

  12. Process for cleaning radioactively contaminated metal surfaces

    International Nuclear Information System (INIS)

    Mihram, R.G.; Snyder, G.A.

    1975-01-01

    A process is described for removing radioactive scale from a ferrous metal surface, including the steps of initially preconditioning the surface by contacting it with an oxidizing solution (such as an aqueous solution of an alkali metal permanganate or hydrogen peroxide), then, after removal or decomposition of the oxidizing solution, the metallic surface is contacted with a cleaning solution which is a mixture of a mineral acid and a complexing agent (such as sulfuric acid and oxalic acid), and which preferably contains a corrosion inhibitor. A final step in the process is the treatment of the spent cleaning solution containing radioactive waste materials in solution by adding a reagent selected from the group consisting of calcium hydroxide or potassium permanganate and an alkali metal hydroxide to thereby form easily recovered metallic compounds containing substantially all of the dissolved metals and radioactivity. (auth)

  13. Metal Poisons for Criticality in Waste Streams

    International Nuclear Information System (INIS)

    Williamson, T.G.; Goslen, A.Q.

    1996-01-01

    Many of the wastes from processing fissile materials contain metals which may serve as nuclear criticality poisons. It would be advantageous to the criticality evaluation of these wastes to demonstrate that the poisons remain with the fissile materials and to demonstrate an always safe poison-to-fissile ratio. The first task, demonstrating that the materials stay together, is the job of the chemist, the second, calculating an always safe ratio, is an object of this paper

  14. Food poisoning. Pt. 2

    Energy Technology Data Exchange (ETDEWEB)

    Askar, A.; Treptow, H.

    1982-01-15

    In the present study information about food poisoning is compared and reviewed. From the viewpoint of a food technologist the toxic substances are represented in four sections: 1. Residues of substances used by plants and animals: pesticides, antibiotics, sexual hormones and psychopharmaces. 2. Environmental contaminants: heavy metals, radionuclides and polycyclic hydrocarbons. 3. Substances developing during the manufacture: food additives, asbest, parts of packing materials, and residual solvents. 4. Substances arising from processing: smoked and roasted food, non enzymatic reaction, oxidized and heated fats and irradiated foods. The mere presence of toxic substances does not make food unsafe or poisonous. Dangerous, because of their toxic or carcinogenic effects are: Pesticides (especially chlorinated organic pesticides), heavy metals (especially lead, mercury and cadmium), polycyclic hydrocarbons (3,4-benzpyren), nitrosamines and vinyl chloride. The other components are only dangerous if they are present in large ammounts. A good and responsible practise of agriculture and food manufacture processes, a watchful and competent official food control and well informed consumers can limit the danger of food poisoning and human health.

  15. Ciguatera poisoning.

    Science.gov (United States)

    Achaibar, Kira C; Moore, Simon; Bain, Peter G

    2007-10-01

    Ciguatera is a form of poisoning that occurs after eating tropical and subtropical ciguatoxic fish. The ciguatoxins are a family of heat stable, lipid soluble cyclic polyether compounds that bind to and open voltage-sensitive Na(+) channels at resting membrane potential, resulting in neural hyperexcitability, as well as swelling of the nodes of Ranvier. The authors describe a 45-year-old man who developed acute gastrointestinal symptoms in Antigua soon after eating red snapper and grouper, potentially "ciguatoxic fish". This was followed by neurological symptoms 24-48 hours later, including temperature reversal (paradoxical dysaesthesia), intense pruritus and increased nociception as a result of a small fibre peripheral neuropathy. The patient's symptoms and small fibre neuropathy improved over a period of 10 months.

  16. Surface-Assisted Dynamic Search Processes.

    Science.gov (United States)

    Shin, Jaeoh; Kolomeisky, Anatoly B

    2018-03-01

    Many chemical and biological systems exhibit intermittent search phenomena when participating particles alternate between dynamic regimes with different dimensionalities. Here we investigate theoretically a dynamic search process of finding a small target on a two-dimensional surface starting from a bulk solution, which is an example of such an intermittent search process. Both continuum and discrete-state stochastic descriptions are developed. It is found that depending on the scanning length λ, which describes the area visited by the reacting molecule during one search cycle, the system can exhibit three different search regimes: (i) For small λ values, the reactant finds the target mostly via three-dimensional bulk diffusion; (ii) for large λ values, the reactant molecule associates to the target mostly via surface diffusion; and (iii) for intermediate λ values, the reactant reaches the target via a combination of three-dimensional and two-dimensional search cycles. Our analysis also shows that the mean search times have different scalings as a function of the size of the surface segment depending on the nature of the dynamic search regime. Search dynamics are also sensitive to the position of the target for large scanning lengths. In addition, it is argued that the continuum description underestimates mean search times and does not always correctly describe the most optimal conditions for the surface-assisted dynamic processes. The importance of our findings for real natural systems is discussed.

  17. Array processing for seismic surface waves

    Energy Technology Data Exchange (ETDEWEB)

    Marano, S.

    2013-07-01

    This dissertation submitted to the Swiss Federal Institute of Technology ETH in Zurich takes a look at the analysis of surface wave properties which allows geophysicists to gain insight into the structure of the subsoil, thus avoiding more expensive invasive techniques such as borehole drilling. This thesis aims at improving signal processing techniques for the analysis of surface waves in various directions. One main contribution of this work is the development of a method for the analysis of seismic surface waves. The method also deals with the simultaneous presence of multiple waves. Several computational approaches to minimize costs are presented and compared. Finally, numerical experiments that verify the effectiveness of the proposed cost function and resulting array geometry designs are presented. These lead to greatly improved estimation performance in comparison to arbitrary array geometries.

  18. Array processing for seismic surface waves

    International Nuclear Information System (INIS)

    Marano, S.

    2013-01-01

    This dissertation submitted to the Swiss Federal Institute of Technology ETH in Zurich takes a look at the analysis of surface wave properties which allows geophysicists to gain insight into the structure of the subsoil, thus avoiding more expensive invasive techniques such as borehole drilling. This thesis aims at improving signal processing techniques for the analysis of surface waves in various directions. One main contribution of this work is the development of a method for the analysis of seismic surface waves. The method also deals with the simultaneous presence of multiple waves. Several computational approaches to minimize costs are presented and compared. Finally, numerical experiments that verify the effectiveness of the proposed cost function and resulting array geometry designs are presented. These lead to greatly improved estimation performance in comparison to arbitrary array geometries

  19. Electrolytic plasma processing of steel surfaces

    International Nuclear Information System (INIS)

    Bejar, M.A; Araya, R.N; Baeza, B

    2006-01-01

    The thermo-chemical treatments of steels with plasma is normally carried out in low-pressure ionized gaseous atmospheres. Among the treatments used most often are: nitruration, carburization and boronized. A plasma can also generate at atmospheric pressure. One way to produce it is with an electrochemical cell that works at a relatively high inter-electrode voltage and under conditions of heavy gas generation. This type of plasma is known as electrolytic plasma. This work studies the feasibility of using electrolytic plasma for the surface processing of steels. Two processes were selected: boronized and nitruration., for the hardening of two types of steel: one with low carbon (1020) and one with low alloy (4140). In the case of the nitruration, the 1020 steel was first aluminized. The electrolytes were aqueous solutions of borax for the boronizing and urea for the nitruration. The electrolytic plasmas were classified qualitatively, in relation with their luminosity by low, medium and high intensity. The boronizing was carried out with low intensity plasmas for a period of one hour. The nitruration was performed with plasmas of different intensities and for period of a few minutes to half an hour. The test pieces processed by electrolytic plasma were characterized by micro-hardness tests and X-ray diffraction. The maximum surface hardnesses obtained for the 1020 and 4140 steels were the following: 300 and 700 HV for the boronizing, and 1650 and 1200 HV for the nitruration, respectively. The utilization of an electrolytic plasma permits the surface processing of steels, noticeably increasing their hardness. With this type of plasma some thermo-chemical surface treatments can be done very rapidly as well (CW)

  20. ENVISAT Land Surface Processes. Phase 2

    Science.gov (United States)

    vandenHurk, B. J. J. M.; Su, Z.; Verhoef, W.; Menenti, M.; Li, Z.-L.; Wan, Z.; Moene, A. F.; Roerink, G.; Jia, I.

    2002-01-01

    This is a progress report of the 2nd phase of the project ENVISAT- Land Surface Processes, which has a 3-year scope. In this project, preparative research is carried out aiming at the retrieval of land surface characteristics from the ENVISAT sensors MERIS and AATSR, for assimilation into a system for Numerical Weather Prediction (NWP). Where in the 1st phase a number of first shot experiments were carried out (aiming at gaining experience with the retrievals and data assimilation procedures), the current 2nd phase has put more emphasis on the assessment and improvement of the quality of the retrieved products. The forthcoming phase will be devoted mainly to the data assimilation experiments and the assessment of the added value of the future ENVISAT products for NWP forecast skill. Referring to the retrieval of albedo, leaf area index and atmospheric corrections, preliminary radiative transfer calculations have been carried out that should enable the retrieval of these parameters once AATSR and MERIS data become available. However, much of this work is still to be carried out. An essential part of work in this area is the design and implementation of software that enables an efficient use of MODTRAN(sub 4) radiative transfer code, and during the current project phase familiarization with these new components has been achieved. Significant progress has been made with the retrieval of component temperatures from directional ATSR-images, and the calculation of surface turbulent heat fluxes from these data. The impact of vegetation cover on the retrieved component temperatures appears manageable, and preliminary comparison of foliage temperature to air temperatures were encouraging. The calculation of surface fluxes using the SEBI concept,which includes a detailed model of the surface roughness ratio, appeared to give results that were in reasonable agreement with local measurements with scintillometer devices. The specification of the atmospheric boundary conditions

  1. Pesticides poisoning

    International Nuclear Information System (INIS)

    Ahmad, I.

    1999-01-01

    Pesticides are chemical toxicants which are used to kill by their toxic actions, the pest organisms, known to incur significant economic losses or threaten human life, his health and that of his domesticated animals. These toxicants are seldom species-specific. The presence of these or their metabolites may scientific be vouched not only in the environment they are used, but in the entire ecosystem, in the subsoil, in the underwater reservoirs and in the food chain of all non-target species including man, his friends i.e. predator and parasite organisms which be uses against the pests, and in his cherished domesticated animals. In the present paper a survey is made of different groups of toxic chemicals generally used to manage pests, in the ecosystem, food chain and tissues and body parts of non-target species including man and the ones dear to him. Toxicology and biochemistry of these toxic materials and their important metabolites are also briefly discussed with special reference to ways and means through which these poison the above non-target species. (author)

  2. Two photon processes in surface photovoltage spectroscopy

    International Nuclear Information System (INIS)

    Craig, R.P.; Thurgate, S.M.

    1996-01-01

    Full text: A significant mid-gap effect has been found in Surface Photovoltage Spectroscopy measurements of cleaved GaAs, InP and Si wafer which is normally interpreted as arising from transitions between surface states and band edges. This large mid-gap effect common to various materials is puzzling as such a high proportion of mid-gap states seems unlikely. Most theories of surface states predict states that tail from the band edges into the gap or states that have a well defined energy in the gap. None propose a large state exactly at E G /2. We recently investigated the variation in SPS spectra with flux density. We find a non-linear correlation in the magnitude of Band-Bending arising from mid-gap and band-gap photon energies. We suggest that the mid-gap feature is due to a two photon absorption process leading to carrier pair generation mediated by mid-gap states in the continuum of band-gap surface states

  3. Poisoning first aid

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/007579.htm Poisoning first aid To use the sharing features on this page, ... burns Stupor Unconsciousness (coma) Unusual breath odor Weakness First Aid Seek immediate medical help. For poisoning by swallowing ...

  4. Bubble bath soap poisoning

    Science.gov (United States)

    ... medlineplus.gov/ency/article/002762.htm Bubble bath soap poisoning To use the sharing features on this page, please enable JavaScript. Bubble bath soap poisoning occurs when someone swallows bubble bath soap. ...

  5. Isopropanol alcohol poisoning

    Science.gov (United States)

    Rubbing alcohol poisoning; Isopropyl alcohol poisoning ... Isopropyl alcohol can be harmful if it is swallowed or gets in the eyes. ... These products contain isopropanol: Alcohol swabs Cleaning supplies ... Rubbing alcohol Other products may also contain isopropanol.

  6. Mercuric chloride poisoning

    Science.gov (United States)

    ... page: //medlineplus.gov/ency/article/002474.htm Mercuric chloride poisoning To use the sharing features on this page, please enable JavaScript. Mercuric chloride is a very poisonous form of mercury. It ...

  7. Diagnosis of acute poisoning

    African Journals Online (AJOL)

    Chantel

    functional tissue damage in ... cury or alcohol) .... †The degree of poisoning, together with drug or poison levels, usually determines the .... monoxide, caffeine and the sym- .... the brain. It usually occurs when two or more drugs, which increase.

  8. Hair straightener poisoning

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002706.htm Hair straightener poisoning To use the sharing features on this page, please enable JavaScript. Hair straightener poisoning occurs when someone swallows products that ...

  9. Hair spray poisoning

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002705.htm Hair spray poisoning To use the sharing features on this page, please enable JavaScript. Hair spray poisoning occurs when someone breathes in (inhales) ...

  10. Hydrochloric acid poisoning

    Science.gov (United States)

    Hydrochloric acid is a clear, poisonous liquid. It is highly corrosive, which means it immediately causes severe damage, such ... poisoning due to swallowing or breathing in hydrochloric acid. This article is for information only. Do NOT ...

  11. Burnable poison rod

    International Nuclear Information System (INIS)

    Natsume, Tomohiro.

    1988-01-01

    Purpose: To decrease the effect of water elimination and the effect of burn-up residue boron, thereby reduce the effect of burnable poison rods as the neutron poisons at the final stage of reactor core lifetime. Constitution: In a burnable poison rod according to the present invention, a hollow burnable poison material is filled in an external fuel can, an inner fuel can mounted with a carbon rod is inserted to the hollow portion of the burnable poison material and helium gases are charged in the outer fuel can. In such a burnable poison rod, the reactivity worths after the burning are reduced to one-half as compared with the conventional case. Accordingly, since the effect of the burnable poison as the neutron poisons is reduced at the final stage of the reactor core of lifetime, the excess reactivity of the reactor core is increased. (Horiuchi, T.)

  12. Surface processing by high power excimer laser

    Energy Technology Data Exchange (ETDEWEB)

    Stehle, M [SOPRA, 92 - Bois-Colombes (France)

    1995-03-01

    Surface processing with lasers is a promising field of research and applications because lasers bring substantial advantages : laser beams work at distance, laser treatments are clean in respect of environment consideration and they offer innovative capabilities for surface treatment which cannot be reached by other way. Excimer lasers are pulsed, gaseous lasers which emit in UV spectral range - the most common are XeCl (308 nm), KrF (248 nm), ArF (193 nm). From 1980 up to 1994, many of them have been used for research, medical and industrial applications such as spectroscopy, PRK (photo-refractive keratotomy) and micro-machining. In the last six years, from 1987 up to 1993, efforts have been done in order to jump from 100 W average power up to 1 kW for XeCl laser at {lambda} = 308 nm. It was the aim of AMMTRA project in Japan as EU205 and EU213 Eureka projects in Europe. In this framework, SOPRA developed VEL (Very large Excimer Laser). In 1992, 1 kW (10 J x 100 Hz) millstone has been reached for the first time, this technology is based on X-Ray preionization and large laser medium (5 liters). Surface treatments based on this laser source are the main purpose of VEL Lasers. Some of them are given for instance : (a) Turbine blades made with metallic substrate and ceramic coatings on the top, are glazed in order to increase corrosion resistance of ceramic and metal sandwich. (b) Selective ablation of organic coatings deposited on fragile composite material is investigated in Aerospace industry. (c) Chock hardening of bulk metallic materials or alloys are investigated for automotive industry in order to increase wear resistance. (d) Ablation of thin surface oxides of polluted steels are under investigation in nuclear industry for decontamination. (J.P.N.).

  13. Surface processing by high power excimer laser

    International Nuclear Information System (INIS)

    Stehle, M.

    1995-01-01

    Surface processing with lasers is a promising field of research and applications because lasers bring substantial advantages : laser beams work at distance, laser treatments are clean in respect of environment consideration and they offer innovative capabilities for surface treatment which cannot be reached by other way. Excimer lasers are pulsed, gaseous lasers which emit in UV spectral range - the most common are XeCl (308 nm), KrF (248 nm), ArF (193 nm). From 1980 up to 1994, many of them have been used for research, medical and industrial applications such as spectroscopy, PRK (photo-refractive keratotomy) and micro-machining. In the last six years, from 1987 up to 1993, efforts have been done in order to jump from 100 W average power up to 1 kW for XeCl laser at λ = 308 nm. It was the aim of AMMTRA project in Japan as EU205 and EU213 Eureka projects in Europe. In this framework, SOPRA developed VEL (Very large Excimer Laser). In 1992, 1 kW (10 J x 100 Hz) millstone has been reached for the first time, this technology is based on X-Ray preionization and large laser medium (5 liters). Surface treatments based on this laser source are the main purpose of VEL Lasers. Some of them are given for instance : a) Turbine blades made with metallic substrate and ceramic coatings on the top, are glazed in order to increase corrosion resistance of ceramic and metal sandwich. b) Selective ablation of organic coatings deposited on fragile composite material is investigated in Aerospace industry. c) Chock hardening of bulk metallic materials or alloys are investigated for automotive industry in order to increase wear resistance. d) Ablation of thin surface oxides of polluted steels are under investigation in nuclear industry for decontamination. (J.P.N.)

  14. Lead Poisoning (For Parents)

    Science.gov (United States)

    ... Staying Safe Videos for Educators Search English Español Lead Poisoning KidsHealth / For Parents / Lead Poisoning What's in ... Print en español La intoxicación por plomo About Lead Poisoning If you have young kids, it's important ...

  15. Marijuana poisoning.

    Science.gov (United States)

    Fitzgerald, Kevin T; Bronstein, Alvin C; Newquist, Kristin L

    2013-02-01

    , tremors, hypothermia, and bradycardia. Higher dosages may additionally cause nystagmus, agitation, tachypnea, tachycardia, ataxia, hyperexcitability, and seizures. Treatment of marijuana ingestion in animals is largely supportive. Vital signs including temperature and heart rate and rhythm must be continually monitored. Stomach content and urine can be tested for cannabinoids. Gas chromatography and mass spectrometry can be utilized for THC detection but usually may take several days and are not practical for initiation of therapy. Human urine drug-screening tests can be unreliable for confirmation of marijuana toxicosis in dogs owing to the interference of a large number of the metabolites in canine urine. False negatives may also arise if testing occurs too recently following THC ingestion. Thus, the use of human urine drug-screening tests in dogs remains controversial. No specific antidote presently exists for THC poisoning. Sedation with benzodiazepines may be necessary if dogs are severely agitated. Intravenous fluids may be employed to counter prolonged vomiting and to help control body temperature. Recently, the use of intralipid therapy to bind the highly lipophilic THC has been utilized to help reduce clinical signs. The majority of dogs experiencing intoxication after marijuana ingestion recover completely without sequellae. Differential diagnoses of canine THC toxicosis include human pharmaceuticals with central nervous system stimulatory effects, drugs with central nervous system depressant effects, macrolide parasiticides, xylitol, and hallucinogenic mushrooms. Copyright © 2013 Elsevier Inc. All rights reserved.

  16. Outsmarting Poison Ivy and Other Poisonous Plants

    Science.gov (United States)

    ... poison sumac. Protectants such as baking soda or colloidal oatmeal relieve minor irritation and itching. Aluminum acetate ... Food and Drug Administration 10903 New Hampshire Avenue Silver Spring, MD 20993 1-888-INFO-FDA (1- ...

  17. Photochemical Transformation Processes in Sunlit Surface Waters

    Science.gov (United States)

    Vione, D.

    2012-12-01

    Photochemical reactions are major processes in the transformation of hardly biodegradable xenobiotics in surface waters. They are usually classified into direct photolysis and indirect or sensitised degradation. Direct photolysis requires xenobiotic compounds to absorb sunlight, and to get transformed as a consequence. Sensitised transformation involves reaction with transient species (e.g. °OH, CO3-°, 1O2 and triplet states of chromophoric dissolved organic matter, 3CDOM*), photogenerated by so-called photosensitisers (nitrate, nitrite and CDOM). CDOM is a major photosensitiser: is it on average the main source of °OH (and of CO3-° as a consequence, which is mainly produced upon oxidation by °OH of carbonate and bicarbonate) and the only important source of 1O2 and 3CDOM* [1, 2]. CDOM origin plays a key role in sensitised processes: allochthonous CDOM derived from soil runoff and rich in fulvic and humic substances is usually more photoactive than autochthonous CDOM (produced by in-water biological processes and mainly consisting of protein-like material) or of CDOM derived from atmospheric deposition. An interesting gradual evolution of CDOM origin and photochemistry can be found in mountain lakes across the treeline, which afford a gradual transition of allochthonous- autochtonous - atmopheric CDOM when passing from trees to alpine meadows to exposed rocks [3]. Another important issue is the sites of reactive species photoproduction in CDOM. While there is evidence that smaller molecular weight fractions are more photoactive, some studies have reported considerable 1O2 reactivity in CDOM hydrophobic sites and inside particles [4]. We have recently addressed the problem and found that dissolved species in standard humic acids (hydrodynamic diameter pollutants to be assessed and modelled. For instance, it is possible to predict pollutant half-life times by knowing absorption spectrum, direct photolysis quantum yield and reaction rate constants with °OH, CO3

  18. Revisiting the association between sea surface temperature and the epidemiology of fish poisoning in the South Pacific: reassessing the link between ciguatera and climate change.

    Science.gov (United States)

    Llewellyn, Lyndon E

    2010-10-01

    The most detailed dataset of ciguatera intensity is that produced by the South Pacific Epidemiological and Health Information Service (SPEHIS) of the Secretariat of the Pacific Community. The SPEHIS fish poisoning database has been previously analysed yielding statistically significant correlations between the Southern Oscillation Index (SOI) and ciguatera case numbers in several countries raising concerns this affliction will increase as oceans warm. Mapping of the SPEHIS records and other data hints at ciguatera not only being restricted to warm waters but that the Indo-Pacific Warm Pool, a body of water that remains hot throughout much of the year, may inhibit ciguatera prevalence. A qualitative assessment of ciguatera intensity and sea surface temperature (SST) behaviour within the EEZ of selected South Pacific nations supported the notion that ciguatera intensity was highest when SST was between an upper and lower limit. Many more climate and SST indices beyond the SOI are now available, including some that measure the abovementioned phenomenon of oceanic warm pools. Statistically significant, positive and negative cross-correlations were obtained between time series of annual ciguatera case rates from the SPEHIS dataset and the Pacific Warm Pool Index and several ENSO related indices which had been lagged for up to 2 years before the ciguatera time series. This further supports the possibility that when considering the impact of climate change on ciguatera, one has to consider two thresholds, namely waters that remain warm enough for a long enough period can lead to ciguatera and that extended periods where the water remains too hot may depress ciguatera case rates. Such a model would complicate projections of the effects of climate change upon ciguatera beyond that of a simple relationship where increased SST may cause more ciguatera. Crown Copyright 2009. Published by Elsevier Ltd. All rights reserved.

  19. Excimer laser surface modification: Process and properties

    Energy Technology Data Exchange (ETDEWEB)

    Jervis, T.R.; Nastasi, M. [Los Alamos National Lab., NM (United States); Hirvonen, J.P. [Technical Research Institute, Espoo (Finland). Metallurgy Lab.

    1992-12-01

    Surface modification can improve materials for structural, tribological, and corrosion applications. Excimer laser light has been shown to provide a rapid means of modifying surfaces through heat treating, surface zone refining, and mixing. Laser pulses at modest power levels can easily melt the surfaces of many materials. Mixing within the molten layer or with the gas ambient may occur, if thermodynamically allowed, followed by rapid solidification. The high temperatures allow the system to overcome kinetic barriers found in some ion mixing experiments. Alternatively, surface zone refinement may result from repeated melting-solidification cycles. Ultraviolet laser light couples energy efficiently to the surface of metallic and ceramic materials. The nature of the modification that follows depends on the properties of the surface and substrate materials. Alloying from both gas and predeposited layer sources has been observed in metals, semiconductors, and ceramics as has surface enrichment of Cr by zone refinement of stainless steel. Rapid solidification after melting often results in the formation of nonequilibrium phases, including amorphous materials. Improved surface properties, including tribology and corrosion resistance, are observed in these materials.

  20. Phosphorus poisoning in waterfowl

    Science.gov (United States)

    Coburn, D.R.; DeWitt, J.B.; Derby, J.V.; Ediger, E.

    1950-01-01

    Black ducks and mallards were found to be highly susceptible to phosphorus poisoning. 3 mg. of white phosphorus per kg. of body weight given in a single dose resulted in death of a black duck in 6 hours. Pathologic changes in both acute and chronic poisoning were studied. Data are presented showing that diagnosis can be made accurately by chemical analysis of stored tissues in cases of phosphorus poisoning.

  1. Hair dye poisoning

    Science.gov (United States)

    Hair tint poisoning ... Different types of hair dye contain different harmful ingredients. The harmful ingredients in permanent dyes are: Naphthylamine Other aromatic amino compounds Phenylenediamines Toluene ...

  2. Process of treating surfaces of metals

    International Nuclear Information System (INIS)

    Kimura, T.; Murao, A.; Kuwahara, T.

    1975-01-01

    Both higher corrosion resistance and paint adherence are given to films formed on the surfaces of metals by treating the surfaces with aqueous solutions of one or more materials selected from the group consisting of water soluble vinyl monomer or water soluble high polymer and then irradiating with ionizing radioactive rays on the nearly dried surface film. When a water soluble inorganic compound is mixed with the above mentioned aqueous solution, the film properties are greatly improved. The inorganic ionic material should contain a cation from the group consisting of Ca, Mg, Zn, Cr, Al, Fe, and Ni. Electron beams may be used. (U.S.)

  3. Modification of surfaces and surface layers by non equilibrium processes

    International Nuclear Information System (INIS)

    Beamson, G.; Brennan, W.J.; Clark, D.T.; Howard, J.

    1988-01-01

    Plasmas are examples of non-equilibrium phenomena which are being used increasingly for the synthesis and modification of materials impossible by conventional routes. This paper introduces methods available by describing the construction and characteristics of some equipment used for the production of different types of plasmas and other non-equilibrium phenomena. This includes high energy ion beams. The special features, advantages and disadvantages of the techniques will be described. There are a multitude of potential application relevant to electronic, metallic, ceramic, and polymeric materials. However, scale-up from the laboratory to production equipment depends on establishing a better understanding of both the physics and chemistry of plasma as well as plasma-solid interactions. Examples are given of how such an understanding can be gained. The chemical analysis of polymer surfaces undergoing modification by inert gas, hydrogen or oxygen plasmas is shown to give physical information regarding the relative roles of diffusion of active species, and direct and radiative energy transfer from the plasma. Surface modification by plasma depositing a new material onto an existing substrate is discussed with particular reference to the deposition of amorphous carbon films. Applications of the unique properties of these films are outlined together with our current understanding of these properties based on chemical and physical methods of analysis of both the films and the plasmas producing them. Finally, surface modification by ion beams is briefly illustrated using examples from the electronics and metals industries where the modification has had a largely physical rather than chemical effect on the starting material. (orig.)

  4. Poison 1 - a programme for calculation of reactivity transients due to fission product poisoning and its application in continuous determination of xenon and samarium poisoning in reactor KS-150

    International Nuclear Information System (INIS)

    Rana, S.B.

    1973-12-01

    The report contains a user's description of the 3-dimensional programme POISON 1 for calculating reactivity transients due to fission-product poisoning during changes of reactor power. The chapter dealing with Xe poisoning contains a description of Xe tables, the method of operational determination of Xe poisoning, use of Xe transients for calibrating control rods and means of shutting down the reactor without being overriden by Xe poisoning. Sm poisoning is determined continuously on the basis of the power diagram of reactor operation. In conclusion a possibility of using the programme in a process computer in combination with self-powered detectors as local power sensors is indicated. (author)

  5. Diffusion processes in bombardment-induced surface topography

    International Nuclear Information System (INIS)

    Robinson, R.S.

    1984-01-01

    A treatment is given of the problem of surface diffusion processes occurring during surface topography development, whenever a surface is simultaneously seeded with impurities and ion bombarded. The development of controllable topography and the importance of surface diffusion parameters, which can be obtained during these studies, are also analyzed. 101 refs.; 7 figs.; 2 tabs

  6. Histamine fish poisoning revisited.

    Science.gov (United States)

    Lehane, L; Olley, J

    2000-06-30

    Histamine (or scombroid) fish poisoning (HFP) is reviewed in a risk-assessment framework in an attempt to arrive at an informed characterisation of risk. Histamine is the main toxin involved in HFP, but the disease is not uncomplicated histamine poisoning. Although it is generally associated with high levels of histamine (> or =50 mg/100 g) in bacterially contaminated fish of particular species, the pathogenesis of HFP has not been clearly elucidated. Various hypotheses have been put forward to explain why histamine consumed in spoiled fish is more toxic than pure histamine taken orally, but none has proved totally satisfactory. Urocanic acid, like histamine, an imidazole compound derived from histidine in spoiling fish, may be the "missing factor" in HFP. cis-Urocanic acid has recently been recognised as a mast cell degranulator, and endogenous histamine from mast cell degranulation may augment the exogenous histamine consumed in spoiled fish. HFP is a mild disease, but is important in relation to food safety and international trade. Consumers are becoming more demanding, and litigation following food poisoning incidents is becoming more common. Producers, distributors and restaurants are increasingly held liable for the quality of the products they handle and sell. Many countries have set guidelines for maximum permitted levels of histamine in fish. However, histamine concentrations within a spoiled fish are extremely variable, as is the threshold toxic dose. Until the identity, levels and potency of possible potentiators and/or mast-cell-degranulating factors are elucidated, it is difficult to establish regulatory limits for histamine in foods on the basis of potential health hazard. Histidine decarboxylating bacteria produce histamine from free histidine in spoiling fish. Although some are present in the normal microbial flora of live fish, most seem to be derived from post-catching contamination on board fishing vessels, at the processing plant or in the

  7. Amnesic Shellfish Poisoning

    Science.gov (United States)

    ... Since then, the death or stranding of other marine animals, including whales, has been suspected or confirmed to ... sickened or die due to domoic acid poisoning. Animals poisoned by domoic acid include seabirds and marine mammals, including sea lions, sea otters, whales. Domoic- ...

  8. Poisoning - Multiple Languages

    Science.gov (United States)

    ... Well-Being 6 - Poison Safety - Amarɨñña / አማርኛ (Amharic) MP3 Siloam Family Health Center Arabic (العربية) Expand Section ... Well-Being 6 - Poison Safety - myanma bhasa (Burmese) MP3 Siloam Family Health Center Dari (دری) Expand Section ...

  9. Arsenical poisoning of racehorses

    Energy Technology Data Exchange (ETDEWEB)

    Sutherland, G.N.; Fawell, E.V.; Brown, J.K.

    1964-03-07

    A case of arsenic poisoning in a training stable of Thoroughbred racehorses is described. This was due to the accidental spilling of an arsenical rat poison into the corn bin. Nine horses were affected. The mortality rate was 100 per cent. 1 table.

  10. Amnesic Shellfish Poisoning (ASP)

    DEFF Research Database (Denmark)

    Ravn, H.

    HAB Publ. Ser. vol 1 is a supplement to Chapter 7 Mehtods for Domoic Acid, the Amnesic Shellfish Poisons in the IOC Manual of Harmful Marine Microalgae......HAB Publ. Ser. vol 1 is a supplement to Chapter 7 Mehtods for Domoic Acid, the Amnesic Shellfish Poisons in the IOC Manual of Harmful Marine Microalgae...

  11. Gaseous poison injection device

    International Nuclear Information System (INIS)

    Kubota, Ryuji; Sugisaki, Toshihiko; Inada, Ikuo.

    1983-01-01

    Purpose: To rapidly control the chain reaction due to thermal neutrons in a reactor core by using gaseous poisons as back-up means for control rod drives. Constitution: Gaseous poisons having a large neutron absorption cross section are used as back-up means for control rod drives. Upon failure of control rod insertion, the gaseous poisons are injected into the lower portion of the reactor core to control the reactor power. As the gaseous poisons, vapors at a high temperature and a higher pressure than that of the coolants in the reactor core are injected to control the reactor power due to the void effects. Since the gaseous poisons thus employed rapidly reach the reactor core and form gas bubbles therein, the deccelerating effect of the thermal neutrons is decreased to reduce the chain reaction. (Moriyama, K.)

  12. Mineralogy of the Martian Surface: Crustal Composition to Surface Processes

    Science.gov (United States)

    Mustard, John F.

    1999-01-01

    Over the course of this award we have: 1) Completed and published the results of a study of the effects of hyperfine particles on reflectance spectra of olivine and quartz, which included the development of scattering codes. Research has also progressed in the analysis of the effects of fine particle sizes on clay spectra. 2) Completed the analysis of the mineralogy of dark regions, showed the insitu compositions are highly correlated to the SNC meteorites, and determined that the martian mantle was depleted in aluminum prior to 2-3 GA ago; Studies of the mineralogic heterogeneity of surficial materials on Mars have also been conducted. and 3) Performed initial work on the study of the physical and chemical processes likely to form and modify duricrust. This includes assessments of erosion rates, solubility and transport of iron in soil environments, and models of pedogenic crust formation.

  13. Surface processing: existing and potential applications of ultraviolet light.

    Science.gov (United States)

    Manzocco, Lara; Nicoli, Maria Cristina

    2015-01-01

    Solid foods represent optimal matrices for ultraviolet processing with effects well beyond nonthermal surface disinfection. UV radiation favors hormetic response in plant tissues and degradation of toxic compound on the product surface. Photoinduced reactions can also provide unexplored possibilities to steer structure and functionality of food biopolymers. The possibility to extensively exploit this technology will depend on availability of robust information about efficacious processing conditions and adequate strategies to completely and homogeneously process food surface.

  14. Lead poisoning in dogs

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, M R; Lewis, G

    1963-08-03

    Within a short period, 14 cases of lead poisoning in the dogs have been encountered. A detailed record appears justified as no published reference can be found to this condition occurring in Britain and because reports from other countries stress the similarity of the clinical manifestations of lead poisoning to those of the common infections of the dog. Five of the 14 clinical cases of lead poisoning are described. The available literature is reviewed and the diagnosis and significance of the condition discussed. 19 references, 2 tables.

  15. Zerodur polishing process for high surface quality and high efficiency

    International Nuclear Information System (INIS)

    Tesar, A.; Fuchs, B.

    1992-08-01

    Zerodur is a glass-ceramic composite importance in applications where temperature instabilities influence optical and mechanical performance, such as in earthbound and spaceborne telescope mirror substrates. Polished Zerodur surfaces of high quality have been required for laser gyro mirrors. Polished surface quality of substrates affects performance of high reflection coatings. Thus, the interest in improving Zerodur polished surface quality has become more general. Beyond eliminating subsurface damage, high quality surfaces are produced by reducing the amount of hydrated material redeposited on the surface during polishing. With the proper control of polishing parameters, such surfaces exhibit roughnesses of < l Angstrom rms. Zerodur polishing was studied to recommend a high surface quality polishing process which could be easily adapted to standard planetary continuous polishing machines and spindles. This summary contains information on a polishing process developed at LLNL which reproducibly provides high quality polished Zerodur surfaces at very high polishing efficiencies

  16. Auger processes in ion-surface collisions

    International Nuclear Information System (INIS)

    Zampieri, Guillermo.

    1985-01-01

    Bombardment of solid targets with low-energy noble gas ions can produce Auger electron emission from the target atoms and/or from the projectiles. In the case of Auger emission from the projectile, Auger emission was observed during the bombardment of Na, Mg, Al and Si with Ne + ions. This emission was studied as a function of the energy, incidence angle and charge state of the projectile. From the analysis, it is concluded that the emission originates in the decay in vacuum of excited and reflected Ne atoms, moving outside the surface. Auger emission was not observed during the bombardment of K, V and Ni with Ar + ions; Zr and Cs with Kr + , and Xe + ions, respectively; and Li and Be with He + ions. In the case of Auger emission from the target, studies of certain aspects of the Na, Mg and Al Auger electron emission spectra were made. The results allow to identify two components in the Auger feature, coresponding to two kinds of Auger transition. The total spectra results from the superposition of both kinds of emission. Auger spectra from K obtained during Ar + and K + bombardment of K-implanted Be, Mg, Al and Cu were also analyzed. Similar to the Na, Mg and Al Auger spectra, the K Auger feature is composed of an atomic like peak superimposed on a bandlike structure. Both components correspond to Auger transitions in K atoms with a 3p vacancy, occuring in vacuum and inside the solid, respectively. (M.E.L.) [es

  17. Study on the treatment of acute thallium poisoning.

    Science.gov (United States)

    Zhang, Hong-Tao; Qiao, Bao-Ping; Liu, Bao-Ping; Zhao, Xian-Guo

    2014-05-01

    Acute thallium poisoning rarely occurs but is a serious and even fatal medical condition. Currently, patients with acute thallium poisoning are usually treated with Prussian blue and blood purification therapy. However, there are few studies about these treatments for acute thallium poisoning. Nine patients with acute thallium poisoning from 1 family were treated successfully with Prussian blue and different types of blood purification therapies and analyzed. Prussian blue combined with sequential hemodialysis, hemoperfusion and/or continuous veno-venous hemofiltration were effective for the treatment of patients with acute thallium poisoning, even after delayed diagnosis. Blood purification therapies help in the clearance of thallium in those with acute thallium poisoning. Prussian blue treatment may do the benefit during this process.

  18. Sodium hydroxide poisoning

    Science.gov (United States)

    Sodium hydroxide is a very strong chemical. It is also known as lye and caustic soda. This ... poisoning from touching, breathing in (inhaling), or swallowing sodium hydroxide. This article is for information only. Do ...

  19. Carbon Monoxide Poisoning

    Science.gov (United States)

    ... found in fumes produced any time you burn fuel in cars or trucks, small engines, stoves, lanterns, ... prevent CO poisoning in my home? Install a battery-operated or battery back-up CO detector in ...

  20. Swimming pool cleaner poisoning

    Science.gov (United States)

    Swimming pool cleaner poisoning occurs when someone swallows this type of cleaner, touches it, or breathes in ... The harmful substances in swimming pool cleaner are: Bromine ... copper Chlorine Soda ash Sodium bicarbonate Various mild acids

  1. Drain cleaner poisoning

    Science.gov (United States)

    ... Activated charcoal, which is used to treat other types of poisoning does not effectively treat (adsorb) sodium hydroxide. For skin exposure, treatment may include: Surgical removal of burned skin (debridement) Transfer to a hospital that specializes in burn ...

  2. Poison Ivy Dermatitis

    Science.gov (United States)

    ... Category: Share: Yes No, Keep Private Poison Ivy Dermatitis Share | "Leaves of three - let it be!" aptly ... is caused by an allergic reaction ( allergic contact dermatitis ) to the oily coating that covers of these ...

  3. Asphalt cement poisoning

    Science.gov (United States)

    ... petroleum material that hardens when it cools. Asphalt cement poisoning occurs when someone swallows asphalt. If hot ... found in: Road paving materials Roofing materials Tile cements Asphalt may also be used for other purposes.

  4. Jerusalem cherry poisoning

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/002871.htm Jerusalem cherry poisoning To use the sharing features on this page, please enable JavaScript. The Jerusalem cherry is a plant that belongs to the ...

  5. Chicken and Food Poisoning

    Science.gov (United States)

    ... this? Submit What's this? Submit Button Past Emails Chicken and Food Poisoning Language: English (US) Español (Spanish) ... on Facebook Tweet Share Compartir Americans eat more chicken every year than any other meat. Chicken can ...

  6. Tips to Prevent Poisonings

    Science.gov (United States)

    ... hours a day, 7 days a week. Be Smart about Storage Store all medicines and household products ... call medicine "candy." Identify poisonous plants in your house and yard and place them out of reach ...

  7. Sodium hypochlorite poisoning

    Science.gov (United States)

    ... that can cause choking and serious breathing problems. Symptoms of sodium hypochlorite poisoning may include: Burning, red eyes Chest pain Coma Coughing (from the fumes) Delirium Gagging sensation Low blood pressure Pain in the ...

  8. Sodium carbonate poisoning

    Science.gov (United States)

    Sodium carbonate (known as washing soda or soda ash) is a chemical found in many household and industrial products. This article focuses on poisoning due to sodium carbonate. This article is for information only. Do NOT ...

  9. [Suicidal poisoning with benzodiazepines].

    Science.gov (United States)

    Chodorowski, Z; Sein Anand, J

    1997-01-01

    In the period from 1987 to 1996, 103 patients with suicidal benzodiazepines poisoning were treated, including 62 women and 41 men from 16 to 79 (mean 34) years old. 23 persons were poisoned only by benzodiazepines, in 80 remaining cases intoxications were mixed eg. including benzodiazepines and alcohol, tricyclic antidepressants, barbiturates, opioids, phenothiazines. The main causes of suicides were mainly depression, drug addiction and alcoholism. Nobody died in the benzodiazepines group, while mortality rate in the group of mixed poisoning was 4%. Prescribing benzodiazepines by physicians was quite often not justified and facilitated, among others, accumulation of the dose sufficient for suicide attempt. Flumazenil was efficient for leading out from coma in 86% of cases with poisoning only by benzodiazepines and 13% of cases with mixed intoxications mainly containing benzodiazepines and alcohol or carbamazepine.

  10. Lip moisturizer poisoning

    Science.gov (United States)

    ... Science of Poisons . 8th ed. New York, NY: McGraw-Hill Education/Medical; 2013:chap 6. Review Date ... urac.org). URAC's accreditation program is an independent audit to verify that A.D.A.M. follows ...

  11. Nail polish poisoning

    Science.gov (United States)

    ... Science of Poisons . 8th ed. New York, NY: McGraw-Hill Medical; 2013:chap 24. Kulig K. General ... urac.org). URAC's accreditation program is an independent audit to verify that A.D.A.M. follows ...

  12. Burnable poison rod

    International Nuclear Information System (INIS)

    Natsume, Tomohiro.

    1988-01-01

    Purpose: To increase the reactor core lifetime by decreasing the effect of neutron absorption of burnable poison rods by using material with less neutron absorbing effect. Constitution: Stainless steels used so far as the coating material for burnable poison rods have relatively great absorption in the thermal neutral region and are not preferred in view of the neutron economy. Burnable poison rods having fuel can made of zirconium alloy shows absorption the thermal neutron region lower by one digit than that of stainless steels but they shows absorption in the resonance region and the cost is higher. In view of the above, the fuel can of the burnable poison material is made of aluminum or aluminu alloy. This can reduce the neutron absorbing effect by stainless steel fuel can and effectively utilize neutrons that have been wastefully absorbed and consumed in stainless steels. (Takahashi, M.)

  13. Benzodiazepine poisoning in elderly

    OpenAIRE

    Perković-Vukčević Nataša; Vuković-Ercegović Gordana; Šegrt Zoran; Đorđević Snežana; Jović-Stošić Jasmina

    2016-01-01

    Background/Aim. Benzodiazepines are among the most frequently ingested drugs in self-poisonings. Elderly may be at greater risk compared with younger individuals due to impaired metabolism and increased sensitivity to benzodiazepines. The aim of this study was to assess toxicity of benzodiazepines in elderly attempted suicide. Methods. A retrospective study of consecutive presentations to hospital after self-poisoning with benzodiazepines was done. Collecte...

  14. Snakebite poisoning in Spain.

    Science.gov (United States)

    Martín-Sierra, Cristina; Nogué-Xarau, Santiago; Pinillos Echeverría, Miguel Ángel; Rey Pecharromán, José Miguel

    2018-01-01

    Emergencies due to snakebites, although unusual in Spain, are potentially serious. Of the 13 species native to the Iberian peninsula, only 5 are poisonous: 2 belong to the Colubridae family and 3 to the Viperidae family. Bites from these venemous snakes can be life-threatening, but the venomous species can be easily identified by attending to certain physical traits. Signs denoting poisoning from vipers, and the appropriate treatment to follow, have changed in recent years.

  15. Cartap Hydrochloride Poisoning.

    Science.gov (United States)

    Kalyaniwala, Kimmin; Abhilash, Kpp; Victor, Peter John

    2016-08-01

    Cartap hydrochloride is a moderately hazardous nereistoxin insecticide that is increasingly used for deliberate self-harm in India. It can cause neuromuscular weakness resulting in respiratory failure. We report a patient with 4% Cartap hydrochloride poisoning who required mechanical ventilation for 36-hours. He recovered without any neurological deficits. We also review literature on Cartap hydrochloride poisoning. © Journal of the Association of Physicians of India 2011.

  16. Superhydrophobic coatings for aluminium surfaces synthesized by chemical etching process

    Directory of Open Access Journals (Sweden)

    Priya Varshney

    2016-10-01

    Full Text Available In this paper, the superhydrophobic coatings on aluminium surfaces were prepared by two-step (chemical etching followed by coating and one-step (chemical etching and coating in a single step processes using potassium hydroxide and lauric acid. Besides, surface immersion time in solutions was varied in both processes. Wettability and surface morphologies of treated aluminium surfaces were characterized using contact angle measurement technique and scanning electron microscopy, respectively. Microstructures are formed on the treated aluminium surfaces which lead to increase in contact angle of the surface (>150°. Also on increasing immersion time, contact angle further increases due to increase in size and depth of microstructures. Additionally, these superhydrophobic coatings show excellent self-cleaning and corrosion-resistant behavior. Water jet impact, floatation on water surface, and low temperature condensation tests assert the excellent water-repellent nature of coatings. Further, coatings are to be found mechanically, thermally, and ultraviolet stable. Along with, these coatings are found to be excellent regeneration ability as verified experimentally. Although aforesaid both processes generate durable and regenerable superhydrophobic aluminium surfaces with excellent self-cleaning, corrosion-resistant, and water-repellent characteristics, but one-step process is proved more efficient and less time consuming than two-step process and promises to produce superhydrophobic coatings for industrial applications.

  17. Finding of CT and clinical in paraquat poisoning pulmonary injury

    International Nuclear Information System (INIS)

    He Zaifang; Li Hongbing; Cheng Shoulin; Li Qixiang; Huang Zhen; Zeng Jianguo

    2012-01-01

    Objective: To investigate the CT features of pulmonary injury in paraquat poisoning. Methods: The chest CT image of lung injury in 6 cases of paraquat poisoning were analyzed retrospectively. According to different period of poisoning, the 6 cases were divided into 3 types:the early stage of poisoning (within 2 d), the middle stage of poisoning (3-14 d), the late stage of poisoning (>14 d). A comparison between CT signs and the pathological features of patients was made. Results: Among this 6 cases, 3 cases died, 2 cases pulmonary fibrosis was noted, 1 cases recovered. According to different period of poisoning, the 6 cases were divided into 3 stages: in the early stage of poisoning (within 2 d), 3 cases of all patients showed nothing remarkable, 2 cases showed ground-glass opacity, 1 case showed fuzzy lung-marking.In the middle stage of poisoning (3-14 d), all 6 cases showed ground-glass opacity, mosaic attenuation; 6 cases showed pulmonary consolidation; 4 cases showed subpleural lines; 4 cases showed bronchiectasis; 2 cases showed mid-lower pleural effusion. In the late stage of poisoning (>14 d), 4 cases showed pulmonary consolidation and pulmonary fibrosis, 3 cases showed ground-glass opacity and mosaic attenuation, 1 case showed mid-lower pleural effusion; 1 case showed mediastinal emphysema. Conclusion: The clinical pathology process of paraquat poisoning was in line with CT finding which was related with clinical stage and was helpful for clinical assessment of paraquat poisoning promptly and to guide the clinical treatment. (authors)

  18. SURFACE CAST IRON STRENGTHENING USING COMBINED LASER AND ULTRASONIC PROCESSING

    Directory of Open Access Journals (Sweden)

    O. G. Devojno

    2013-01-01

    Full Text Available The paper provides an analysis of ultrasonic surface plastic deformation and subsequent laser thermal strengthening of gray cast iron parts in the regime of hardening from a solid state with the purpose to obtain strengthened surface layers of bigger depth and less roughness of the processed surface. Program complex ANSYS 11.0 has been used for calculation of temperature fields induced by laser exposure.  The appropriate regime of laser processing without surface fusion has been selected on the basis of the applied complex. The possibility of displacement in the bottom boundary of α–γ-transformation temperature  for СЧ20 with 900 °С up to 800 °С is confirmed due to preliminary ultrasonic surface plastic deformation of the surface that allows to expand technological opportunities of laser quenching  of gray  cast iron from a solid state. 

  19. A restrospective study of acute systemic poisoning of ...

    African Journals Online (AJOL)

    Paraphenylenediamine (PPD) is commonly used in several industries (dyeing furs, photochemical processes, tyre vulcanisation industries, oxidisable hair dye, etc.). Its allergic effect is well established and many studies are devoted to the subject, but PPD systemic poisoning is not understood. Several acute PPD poisoning ...

  20. Diffusion processes in bombardment-induced surface topography

    International Nuclear Information System (INIS)

    Robinson, R.S.

    1984-01-01

    The bombardment of surfaces with moderate energy ions can lead to the development of various micron-sized surface structures. These structures include ridges, ledges, flat planes, pits and cones. The causal phenomena in the production of these features are sputtering, ion reflection, redeposition of sputtered material, and surface diffusion of both impurity and target-atom species. The authors concentrate on the formation of ion bombardment-induced surface topography wherein surface diffusion is a dominant process. The most thoroughly understood aspect of this topography development is the generation of cone-like structures during sputtering. The formation of cones during sputtering has been attributed to three effects. These are: (1) the presence of asperities, defects, or micro-inclusions in the surface layers, (2) the presence of impurities on the surfaces, and (3) particular crystal orientations. (Auth.)

  1. Benzodiazepine poisoning in elderly.

    Science.gov (United States)

    Vukcević, Natasa Perković; Ercegović, Gordana Vuković; Segrt, Zoran; Djordjević, Snezana; Stosić, Jasmina Jović

    2016-03-01

    Benzodiazepines are among the most frequently ingested drugs in self-poisonings. Elderly may be at greater risk compared with younger individuals due to impaired metabolism and increased sensitivity to benzodiazepines. The aim of this study was to assess toxicity of benzodiazepines in elderly attempted suicide. A retrospective study of consecutive presentations to hospital after self-poisoning with benzodiazepines was done. Collected data consisted of patient's characteristics (age, gender), benzodiazepine ingested with its blood concentrations at admission, clinical findings including vital signs and Glasgow coma score, routine blood chemistry, complications of poisoning, details of management, length of hospital stay and outcome. According the age, patients are classified as young (15-40-year old), middle aged (41-65-year old) and elderly (older than 65). During a 2-year observational period 387 patients were admitted because of pure benzodiazepine poisoning. The most frequently ingested drug was bromazepam, the second was diazepam. The incidence of coma was significantly higher, and the length of hospital stay significantly longer in elderly. Respiratory failure and aspiration pneumonia occurred more frequently in old age. Also, flumazenil was more frequently required in the group of elderly patients. Massive benzodiazepines overdose in elderly may be associated with a significant morbidity, including deep coma with aspiration pneumonia, respiratory failure, and even death. Flumazenil is indicated more often to reduce CNS depression and prevent complications of prolonged unconsciousness, but supportive treatment and proper airway management of comatose patients is the mainstay of the treatment of acute benzodiazepine poisoning.

  2. Apparatus and process for the surface treatment of carbon fibers

    Science.gov (United States)

    Paulauskas, Felix Leonard; Ozcan, Soydan; Naskar, Amit K.

    2016-05-17

    A method for surface treating a carbon-containing material in which carbon-containing material is reacted with decomposing ozone in a reactor (e.g., a hollow tube reactor), wherein a concentration of ozone is maintained throughout the reactor by appropriate selection of at least processing temperature, gas stream flow rate, reactor dimensions, ozone concentration entering the reactor, and position of one or more ozone inlets (ports) in the reactor, wherein the method produces a surface-oxidized carbon or carbon-containing material, preferably having a surface atomic oxygen content of at least 15%. The resulting surface-oxidized carbon material and solid composites made therefrom are also described.

  3. Oil-based paint poisoning

    Science.gov (United States)

    Paint - oil-based - poisoning ... Hydrocarbons are the primary poisonous ingredient in oil paints. Some oil paints have heavy metals such as lead, mercury, cobalt, and barium added as pigment. These heavy metals can cause additional ...

  4. Poison ivy - oak - sumac rash

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/000027.htm Poison ivy - oak - sumac rash To use the sharing features on this page, please enable JavaScript. Poison ivy, oak, and sumac are plants that commonly ...

  5. Poison control center - emergency number

    Science.gov (United States)

    For a POISON EMERGENCY call: 1-800-222-1222 ANYWHERE IN THE UNITED STATES This national hotline number will let you ... is a free and confidential service. All local poison control centers in the United States use this ...

  6. An investigation of laser processing of silica surfaces

    International Nuclear Information System (INIS)

    Weber, A.J.; Stewart, A.F.; Exarhos, G.J.; Stowell, W.K.

    1988-01-01

    An initial set of experiments has been conducted to determine the practicality of laser processing of optical substrates. In contrast to earlier work, a high average power CO 2 laser was used to flood load the entire surface of each test sample. Fused silica substrates were laser polished on both surfaces at power densities ranging from 150 to 350 W/cm 2 . During each test sequence sample surface temperatures were recorded using a thermal imaging system. Extensive pre- and post-test characterization revealed that surface roughness and scattering of bare silica surfaces were reduced while internal stress increased. Laser damage thresholds were found to increase only for certain conditions. Changes in the microstructure were observed. These preliminary experiments demonstrate that laser processing can dramatically improve the optical properties of fused silica substrates

  7. Amitraz poisoning: case report

    Directory of Open Access Journals (Sweden)

    Jaime Alexander Molina-Bolaños

    2017-10-01

    Full Text Available Amitraz is an insecticide compound used worldwide for controlling pests, especially in agricultural and livestock areas. However, amitraz poisoning in Colombia is rare. This article reports the case of an 18-year-old female patient who was admitted in the emergency service 3 hours after the intake of an unknown amount of Triatox® (amitraz. The patient presented with a depressed level of consciousness, respiratory distress, hypotension, bradycardia, myosis and metabolic acidosis compensated with respiratory alkalosis. Initial treatment was provided using life support measures in the emergency ward, and subsequent transfer and support in the intensive care unit. She was discharged 24 hours after admission. This case considers the clinical similarity between amitraz poisoning and poisoning caused by other more frequent toxic compounds such as carbamates, organophosphates and opioids, which require different management.

  8. Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    Alisa Wray

    2016-07-01

    Full Text Available Audience: This oral boards case is appropriate for all emergency medicine learners (residents, interns, and medical students. Introduction: Carbon monoxide (CO is a colorless and odorless gas that typically results from combustion. It binds hemoglobin, dissociating oxygen, causing headache, weakness, confusion and possible seizure or coma. Pulse oxygen levels may be falsely elevated. Practitioners should maintain a high index of suspicion for carbon monoxide poisoning. If caught early CO poisoning is reversible with oxygen or hyperbaric oxygen therapy. Objectives: The learner will assess a patient with altered mental status and weakness, ultimately identifying that the patient has carbon monoxide poisoning. The learner will treat the patient with oxygen and admit/transfer the patient for hyperbaric oxygenation. Method: Oral boards case

  9. [Electronic poison information management system].

    Science.gov (United States)

    Kabata, Piotr; Waldman, Wojciech; Kaletha, Krystian; Sein Anand, Jacek

    2013-01-01

    We describe deployment of electronic toxicological information database in poison control center of Pomeranian Center of Toxicology. System was based on Google Apps technology, by Google Inc., using electronic, web-based forms and data tables. During first 6 months from system deployment, we used it to archive 1471 poisoning cases, prepare monthly poisoning reports and facilitate statistical analysis of data. Electronic database usage made Poison Center work much easier.

  10. Extracorporeal treatment for thallium poisoning

    DEFF Research Database (Denmark)

    Ghannoum, Marc; Nolin, Thomas D; Goldfarb, David S

    2012-01-01

    The EXtracorporeal TReatments In Poisoning (EXTRIP) workgroup was formed to provide recommendations on the use of extracorporeal treatment (ECTR) in poisoning. To test and validate its methods, the workgroup reviewed data for thallium (Tl).......The EXtracorporeal TReatments In Poisoning (EXTRIP) workgroup was formed to provide recommendations on the use of extracorporeal treatment (ECTR) in poisoning. To test and validate its methods, the workgroup reviewed data for thallium (Tl)....

  11. Carbon Monoxide (CO) Poisoning Prevention

    Science.gov (United States)

    ... family by acting wisely in case of a power outage and learning the symptoms of CO poisoning. How to Recognize CO Poisoning The most common symptoms of CO poisoning are headache, dizziness, weakness, nausea, vomiting, chest pain, and confusion. People who are sleeping or who ...

  12. Black-spot poison ivy.

    Science.gov (United States)

    Schram, Sarah E; Willey, Andrea; Lee, Peter K; Bohjanen, Kimberly A; Warshaw, Erin M

    2008-01-01

    In black-spot poison ivy dermatitis, a black lacquerlike substance forms on the skin when poison ivy resin is exposed to air. Although the Toxicodendron group of plants is estimated to be the most common cause of allergic contact dermatitis in the United States, black-spot poison ivy dermatitis is relatively rare.

  13. Carbon Monoxide Poisoning

    Directory of Open Access Journals (Sweden)

    Kamal Mishra

    2016-01-01

    Full Text Available Introduction: Carbon monoxide is known as the silent killer, being colorless, odourless, and tasteless. Initially non-irritating, it is very difficult for people to detect Carbon monoxide is a product of incomplete combustion of organic matter due to insufficient oxygen supply that prevents complete oxidation of carbon to C02. During World War II, Nazis used gas vans to kill an estimated over 700,000 prisoners by carbon monoxide poisoning. This method was also used in the gas chambers ofseveral death camps. The true number of incidents of carbon monoxide poisoning is unknown, since many non-lethal exposures go undetected From the available data, carbon monoxide poisoning is the most common cause of injury and death due to poisoning worldwide. Clinical features and management: The signs of carbon monoxide poisoning vary with concentration and length of exposure. Subtle cardiovascular or neurobehavioural effects occur at low concentration. The onset of chronic poisoning is usually insidious and easily mistaken for viral prodrome, depression, or gastroenteritis in children. The classic sign of carbon monoxide poisoning which is actually more often seen in the dead than the living is appearing red-cheeked and healthy. Cherry pink colour develops in nails, skin and mucosa. In acute poisoning, common abnormalities of posture and tone are cogwheel rigidity, opisthotonus, spasticity or flaccidity and seizures. Retinal haemorrhages and the classic cherry red skin colour are seldom seen. Different people andpopulations may have different carbon monoxide tolerance levels. On average, exposures at 100ppm or greater is dangerous to human health. Treatment and prevention: The mainstay of treatment is 100% oxygen administration until the COHb level is normal When the patient is stable enough to be transported, hyperbaric oxygen (HBOT should be considered This treatment is safe and well tolerated Public education about the danger of carbon monoxide, with

  14. Plasma nitriding - an eco friendly surface hardening process

    International Nuclear Information System (INIS)

    Mukherjee, S.

    2015-01-01

    Surface hardening is a process of heating the metal such that the surface gets only hardened. This process is adopted for many components like gears, cams, and crankshafts, which desire high hardness on the outer surface with a softer core to withstand the shocks. So, to attain such properties processes like carburising, nitriding, flame hardening and induction hardening are employed. Amongst these processes nitriding is the most commonly used process by many industries. In nitriding process the steel material is heated to a temperature of around 550 C and then exposed to atomic nitrogen. This atomic nitrogen reacts with iron and other alloying elements and forms nitrides, which are very hard in nature. By this process both wear resistance and hardness of the product can be increased. The atomic nitrogen required for this process can be obtained using ammonia gas (gas nitriding), cyanide based salt bath (liquid nitriding) and plasma medium (plasma nitriding). However, plasma nitriding has recently received considerable industrial interest owing to its characteristic of faster nitrogen penetration, short treatment time, low process temperature, minimal distortion, low energy use and easier control of layer formation compared with conventional techniques such as gas and liquid nitriding. This process can be used for all ferrous materials including stainless steels. Plasma nitriding is carried out using a gas mixture of nitrogen and hydrogen gas at sub atmospheric pressures hence, making it eco-friendly in nature. Plasma nitriding allows modification of the surface layers and hardness profiles by changing the gas mixture and temperature. The wide applicable temperature range enables a multitude of applications, beyond the possibilities of gas or salt bath processes. This has led to numerous applications of this process in industries such as the manufacture of machine parts for plastics and food processing, packaging and tooling as well as pumps and hydraulic, machine

  15. Surface processing for bulk niobium superconducting radio frequency cavities

    Science.gov (United States)

    Kelly, M. P.; Reid, T.

    2017-04-01

    The majority of niobium cavities for superconducting particle accelerators continue to be fabricated from thin-walled (2-4 mm) polycrystalline niobium sheet and, as a final step, require material removal from the radio frequency (RF) surface in order to achieve performance needed for use as practical accelerator devices. More recently bulk niobium in the form of, single- or large-grain slices cut from an ingot has become a viable alternative for some cavity types. In both cases the so-called damaged layer must be chemically etched or electrochemically polished away. The methods for doing this date back at least four decades, however, vigorous empirical studies on real cavities and more fundamental studies on niobium samples at laboratories worldwide have led to seemingly modest improvements that, when taken together, constitute a substantial advance in the reproducibility for surface processing techniques and overall cavity performance. This article reviews the development of niobium cavity surface processing, and summarizes results of recent studies. We place some emphasis on practical details for real cavity processing systems which are difficult to find in the literature but are, nonetheless, crucial for achieving the good and reproducible cavity performance. New approaches for bulk niobium surface treatment which aim to reduce cost or increase performance, including alternate chemical recipes, barrel polishing and ‘nitrogen doping’ of the RF surface, continue to be pursued and are closely linked to the requirements for surface processing.

  16. Important Poisonous Plants in Tibetan Ethnomedicine

    Directory of Open Access Journals (Sweden)

    Lijuan Ma

    2015-01-01

    Full Text Available Tibetan ethnomedicine is famous worldwide, both for its high effectiveness and unique cultural background. Many poisonous plants have been widely used to treat disorders in the Tibetan medicinal system. In the present review article, some representative poisonous plant species are introduced in terms of their significance in traditional Tibetan medicinal practices. They are Aconitum pendulum, Strychnos nux-vomica, Datura stramonium and Anisodus tanguticus, for which the toxic chemical constituents, bioactivities and pharmacological functions are reviewed herein. The most important toxins include aconitine, strychnine, scopolamine, and anisodamine. These toxic plants are still currently in use for pain-reduction and other purposes by Tibetan healers after processing.

  17. Certain cases of poisoning by arsenic

    Energy Technology Data Exchange (ETDEWEB)

    Cristol, P; Fourcade, J; Ravoire, J; Bezenech, C

    1939-05-01

    Cases of acute and chronic poisoning by arsenic are reported. Diffuse pains, angor, edema of the limbs and genitals, complicated by heptic insufficiency and chronic bronchitis were determined in a subject having lived near an industrial plant processing arseniferous ores for several years. The plant emitted several hundred kg of finely dispersed arsenic oxide daily which settled on forage and vegetables. Symptoms of poisoning by arsenic were also detected in cattle in the same area. The installation of Cottrell type dust separators has helped to suppress the arsenic oxide emissions.

  18. Surface engineering of glazing materials and structures using plasma processes

    International Nuclear Information System (INIS)

    Anders, Andre; Monteiro, Othon R.

    2003-01-01

    A variety of coatings is commercially produced on a very large scale, including transparent conducting oxides and multi-layer silver-based low-emissivity and solar control coatings. A very brief review of materials and manufacturing process is presented and illustrated by ultrathin silver films and chevron copper films. Understanding the close relation between manufacturing processes and bulk and surface properties of materials is crucial for film growth and self-assembly processes

  19. Surface topography of parallel grinding process for nonaxisymmetric aspheric lens

    International Nuclear Information System (INIS)

    Zhang Ningning; Wang Zhenzhong; Pan Ri; Wang Chunjin; Guo Yinbiao

    2012-01-01

    Workpiece surface profile, texture and roughness can be predicted by modeling the topography of wheel surface and modeling kinematics of grinding process, which compose an important part of precision grinding process theory. Parallel grinding technology is an important method for nonaxisymmetric aspheric lens machining, but there is few report on relevant simulation. In this paper, a simulation method based on parallel grinding for precision machining of aspheric lens is proposed. The method combines modeling the random surface of wheel and modeling the single grain track based on arc wheel contact points. Then, a mathematical algorithm for surface topography is proposed and applied in conditions of different machining parameters. The consistence between the results of simulation and test proves that the algorithm is correct and efficient. (authors)

  20. Plasma assisted surface coating/modification processes: An emerging technology

    Science.gov (United States)

    Spalvins, T.

    1986-01-01

    A broad understanding of the numerous ion or plasma assisted surface coating/modification processes is sought. An awareness of the principles of these processes is needed before discussing in detail the ion nitriding technology. On the basis of surface modifications arising from ion or plasma energizing and interactions, it can be broadly classified as deposition of distinct overlay coatings (sputtering-dc, radio frequency, magnetron, reactive; ion plating-diode, triode) and surface property modification without forming a discrete coating (ion implantation, ion beam mixing, laser beam irradiation, ion nitriding, ion carburizing, plasma oxidation). These techniques offer a great flexibility and are capable in tailoring desirable chemical and structural surface properties independent of the bulk properties.

  1. Plasma assisted surface coating/modification processes - An emerging technology

    Science.gov (United States)

    Spalvins, T.

    1987-01-01

    A broad understanding of the numerous ion or plasma assisted surface coating/modification processes is sought. An awareness of the principles of these processes is needed before discussing in detail the ion nitriding technology. On the basis of surface modifications arising from ion or plasma energizing and interactions, it can be broadly classified as deposition of distinct overlay coatings (sputtering-dc, radio frequency, magnetron, reactive; ion plating-diode, triode) and surface property modification without forming a discrete coating (ion implantation, ion beam mixing, laser beam irradiation, ion nitriding, ion carburizing, plasma oxidation. These techniques offer a great flexibility and are capable in tailoring desirable chemical and structural surface properties independent of the bulk properties.

  2. Chelation Therapy for Mercury Poisoning

    Directory of Open Access Journals (Sweden)

    Rong Guan

    2009-01-01

    Full Text Available Chelation therapy has been the major treatment for heavy metal poisoning. Various chelating agents have been developed and tested for treatment of heavy metal intoxications, including mercury poisoning. It has been clearly shown that chelating agents could rescue the toxicity caused by heavy metal intoxication, but the potential preventive role of chelating agents against heavy metal poisoning has not been explored much. Recent paper by Siddiqi and colleagues has suggested a protective role of chelating agents against mercury poisoning, which provides a promising research direction for broader application of chelation therapy in prevention and treatment of mercury poisoning.

  3. ANFIS Modeling of the Surface Roughness in Grinding Process

    OpenAIRE

    H. Baseri; G. Alinejad

    2011-01-01

    The objective of this study is to design an adaptive neuro-fuzzy inference system (ANFIS) for estimation of surface roughness in grinding process. The Used data have been generated from experimental observations when the wheel has been dressed using a rotary diamond disc dresser. The input parameters of model are dressing speed ratio, dressing depth and dresser cross-feed rate and output parameter is surface roughness. In the experimental procedure the grinding conditions...

  4. Oven cleaner poisoning

    Science.gov (United States)

    ... do so by poison control or a health care provider. If the chemical is on the skin or in the eyes, flush with lots of water for at least 15 minutes. If the chemical was swallowed, immediately give the person water or milk, unless instructed otherwise by a provider. If the ...

  5. Metal cleaner poisoning

    Science.gov (United States)

    ... do so by poison control or a health care provider. If the chemical is on the skin or in the eyes, flush with lots of water for at least 15 minutes. If the person swallowed the metal cleaner, give them water or milk right away, unless a provider tells you not ...

  6. Carbon monoxide poisoning

    Science.gov (United States)

    ... Animals can also be poisoned by carbon monoxide. People who have pets at home may notice that their animals become ... or unresponsive from carbon monoxide exposure. Often the pets will ... these conditions. This can lead to a delay in getting help.

  7. Sulfur poisoning in cattle

    Energy Technology Data Exchange (ETDEWEB)

    Julian, R J; Harrison, K B

    1975-01-01

    A case of sulfur poisoning is described in which 12 of 20 cattle died following the feeding of sulfur. Respiratory distress and abdominal pain were the prominent signs. Examination of one animal revealed vasculitis and necrosis of the rumen and abomasal wall. The possible toxic effects of sulfur are discussed.

  8. Poison ivy - oak - sumac

    Science.gov (United States)

    ... done more than 1 hour after touching the plant's sap. Flush the eyes out with water. Take care to clean under the fingernails well to remove ... room. If you are concerned, call your health care provider or poison control. At the ... Take a sample of the plant with you to the doctor or hospital, if ...

  9. Heterogeneous burnable poisons:

    International Nuclear Information System (INIS)

    Leiva, Sergio; Agueda, Horacio; Russo, Diego

    1989-01-01

    The use of materials possessing high neutron absorption cross-section commonly known as 'burnable poisons' have its origin in BWR reactors with the purpose of improving the efficiency of the first fuel load. Later on, it was extended to PWR to compensate of initial reactivity without infringing the requirement of maintaining a negative moderator coefficient. The present tendency is to increase the use of solid burnable poisons to extend the fuel cycle life and discharge burnup. There are two concepts for the burnable poisons utilization: 1) heterogeneously distributions in the form of rods, plates, etc. and 2) homogeneous dispersions of burnable poisons in the fuel. The purpose of this work is to present the results of sinterability studies, performed on Al 2 O 3 -B 4 C and Al 2 O 3 -Gd 2 O 3 systems. Experiments were carried on pressing at room temperature mixtures of powders containing up to 5 wt % of B 4 C or Gd 2 O 3 in Al 2 O 3 and subsequently sintering at 1750 deg C in reducing atmosphere. Evaluation of density, porosity and microstructures were done and a comparison with previous experiences is shown. (Author) [es

  10. Poison Prevention Program

    Science.gov (United States)

    Office of Substance Misuse and Addiction Prevention Finance & Management Services Health Care , Technology: For more info about the national Poison Help program and to request materials visit: http Seniors & Disabilities Services Substance Misuse and Addiction Prevention State of Alaska myAlaska My

  11. Scaling behaviour of randomly alternating surface growth processes

    CERN Document Server

    Raychaudhuri, S

    2002-01-01

    The scaling properties of the roughness of surfaces grown by two different processes randomly alternating in time are addressed. The duration of each application of the two primary processes is assumed to be independently drawn from given distribution functions. We analytically address processes in which the two primary processes are linear and extend the conclusions to nonlinear processes as well. The growth scaling exponent of the average roughness with the number of applications is found to be determined by the long time tail of the distribution functions. For processes in which both mean application times are finite, the scaling behaviour follows that of the corresponding cyclical process in which the uniform application time of each primary process is given by its mean. If the distribution functions decay with a small enough power law for the mean application times to diverge, the growth exponent is found to depend continuously on this power-law exponent. In contrast, the roughness exponent does not depe...

  12. [Plant poisoning cases in Turkey].

    Science.gov (United States)

    Oztekin-Mat, A

    1994-01-01

    In Turkey, the majority of the population live in rural areas where they use wild plants as food and medicine. The confusion of an edible plant with a poisonous one give rise to serious poisoning which may even result in death. The incidence of plant poisoning in Turkey is about 6% and especially high among children between ages of 2 and 11 living in rural areas. The number of species that cause poisoning is around twenty and Hyoscyamus niger (Solanaceae), Colchicum species (Liliaceae), Conium maculatum (Umbelliferae) and Prunus species (Rosaceae) are the most important. Mushroom poisoning is more frequent in spring and fall. The main reasons are their widespread usage as food and the inexperience of the gatherers in distinguishing the edibles from the poisonous. Amanita phalloides, A. verna, A. muscaria, A. pantherina are responsible for severe cases of poisoning.

  13. Benzodiazepine poisoning in elderly

    Directory of Open Access Journals (Sweden)

    Perković-Vukčević Nataša

    2016-01-01

    Full Text Available Background/Aim. Benzodiazepines are among the most frequently ingested drugs in self-poisonings. Elderly may be at greater risk compared with younger individuals due to impaired metabolism and increased sensitivity to benzodiazepines. The aim of this study was to assess toxicity of benzodiazepines in elderly attempted suicide. Methods. A retrospective study of consecutive presentations to hospital after self-poisoning with benzodiazepines was done. Collected data consisted of patient's characteristics (age, gender, benzodiazepine ingested with its blood concentrations at admission, clinical findings including vital signs and Glasgow coma score, routine blood chemistry, complications of poisoning, details of management, length of hospital stay and outcome. According the age, patients are classified as young (15-40-year old, middle aged (41-65-year old and elderly (older than 65. Results. During a 2-year observational period 387 patients were admitted because of pure benzodiazepine poisoning. The most frequently ingested drug was bromazepam, the second was diazepam. The incidence of coma was significantly higher, and the length of hospital stay significantly longer in elderly. Respiratory failure and aspiration pneumonia occurred more frequently in old age. Also, flumazenil was more frequently required in the group of elderly patients. Conclusion. Massive benzodiazepines overdose in elderly may be associated with a significant morbidity, including deep coma with aspiration pneumonia, respiratory failure, and even death. Flumazenil is indicated more often to reduce CNS depression and prevent complications of prolonged unconsciousness, but supportive treatment and proper airway management of comatose patients is the mainstay of the treatment of acute benzodiazepine poisoning.

  14. High surface area carbon and process for its production

    Energy Technology Data Exchange (ETDEWEB)

    Romanos, Jimmy; Burress, Jacob; Pfeifer, Peter; Rash, Tyler; Shah, Parag; Suppes, Galen

    2016-12-13

    Activated carbon materials and methods of producing and using activated carbon materials are provided. In particular, biomass-derived activated carbon materials and processes of producing the activated carbon materials with prespecified surface areas and pore size distributions are provided. Activated carbon materials with preselected high specific surface areas, porosities, sub-nm (<1 nm) pore volumes, and supra-nm (1-5 nm) pore volumes may be achieved by controlling the degree of carbon consumption and metallic potassium intercalation into the carbon lattice during the activation process.

  15. Scaling behaviour of randomly alternating surface growth processes

    International Nuclear Information System (INIS)

    Raychaudhuri, Subhadip; Shapir, Yonathan

    2002-01-01

    The scaling properties of the roughness of surfaces grown by two different processes randomly alternating in time are addressed. The duration of each application of the two primary processes is assumed to be independently drawn from given distribution functions. We analytically address processes in which the two primary processes are linear and extend the conclusions to nonlinear processes as well. The growth scaling exponent of the average roughness with the number of applications is found to be determined by the long time tail of the distribution functions. For processes in which both mean application times are finite, the scaling behaviour follows that of the corresponding cyclical process in which the uniform application time of each primary process is given by its mean. If the distribution functions decay with a small enough power law for the mean application times to diverge, the growth exponent is found to depend continuously on this power-law exponent. In contrast, the roughness exponent does not depend on the timing of the applications. The analytical results are supported by numerical simulations of various pairs of primary processes and with different distribution functions. Self-affine surfaces grown by two randomly alternating processes are common in nature (e.g., due to randomly changing weather conditions) and in man-made devices such as rechargeable batteries

  16. The pattern of acute poisoning in a teaching hospital, north-west Ethiopia.

    Science.gov (United States)

    Abula, Teferra; Wondmikun, Yared

    2006-04-01

    Poisoning by means of hazardous chemicals through ignorance, mishap or intentionally is becoming a serious health problem worldwide. Epidemiological data on this important health issue are, however, scarce in Ethiopia. The purpose of this study is to assess the pattern of acute poisonings and determine the approaches employed for the management of poisoning. The medical records of patients with acute poisonings presented to the Gondar University hospital between July 2001 and June 2004 were reviewed retrospectively. One hundred and two patients presenting to the emergency department of the hospital were due to acute poisoning; accounting for about 0.45% of emergency room admissions. Organophosphates, rat poison and alcohol were the commonly encountered poisoning agents (in about 70% of cases) mainly in adults possibly with suicidal or para-suicidal intention. The approaches employed in the management of poisoning mainly involved gastrointestinal decontamination procedures. Specific antidotes were used in a substantial number of patients. The fatality rate was 2.4%. Poisoning with suicidal intention is becoming a serious health problem particularly in adults. Pesticides are commonly used toxicants. The approaches in the management of poisoning are justifiable in some cases. However, much is to be done to improve the recording of patient-related information and record-keeping processes. Further large scale studies are required to investigate national trends of poisoning and factors associated with poisoning.

  17. EXPERIMENTAL VALIDATION OF CUMULATIVE SURFACE LOCATION ERROR FOR TURNING PROCESSES

    Directory of Open Access Journals (Sweden)

    Adam K. Kiss

    2016-02-01

    Full Text Available The aim of this study is to create a mechanical model which is suitable to investigate the surface quality in turning processes, based on the Cumulative Surface Location Error (CSLE, which describes the series of the consecutive Surface Location Errors (SLE in roughing operations. In the established model, the investigated CSLE depends on the currently and the previously resulted SLE by means of the variation of the width of cut. The phenomenon of the system can be described as an implicit discrete map. The stationary Surface Location Error and its bifurcations were analysed and flip-type bifurcation was observed for CSLE. Experimental verification of the theoretical results was carried out.

  18. Particle dry deposition to water surfaces: Processes and consequences

    DEFF Research Database (Denmark)

    Pryor, S.C.; Barthelmie, R.J.

    2000-01-01

    flux to coastal waters, atmosphere-surface exchange represents a significant component of the total flux and may be particularly critical during the summertime when both the riverine input and ambient nutrient concentrations are often at a minimum. In this chapter, we present an overview...... of the physical and chemical processes which dictate the quantity (and direction) of atmosphere-surface fluxes of trace chemicals to (and above) water surfaces with particular emphasis on the role of particles. Dry deposition (transfer to the surface in the absence of precipitation) of particles is determined...... efforts to simulate and measure fluxes close to the coastline. These arise in part from the complexity of atmospheric flow in this region where energy and chemical fluxes are highly inhomogeneous in space and time and thermally generated atmospheric circulations are commonplace. (C) 2000 Elsevier Science...

  19. Monitoring tablet surface roughness during the film coating process

    DEFF Research Database (Denmark)

    Seitavuopio, Paulus; Heinämäki, Jyrki; Rantanen, Jukka

    2006-01-01

    The purpose of this study was to evaluate the change of surface roughness and the development of the film during the film coating process using laser profilometer roughness measurements, SEM imaging, and energy dispersive X-ray (EDX) analysis. Surface roughness and texture changes developing during...... the process of film coating tablets were studied by noncontact laser profilometry and scanning electron microscopy (SEM). An EDX analysis was used to monitor the magnesium stearate and titanium dioxide of the tablets. The tablet cores were film coated with aqueous hydroxypropyl methylcellulose, and the film...... coating was performed using an instrumented pilot-scale side-vented drum coater. The SEM images of the film-coated tablets showed that within the first 30 minutes, the surface of the tablet cores was completely covered with a thin film. The magnesium signal that was monitored by SEM-EDX disappeared after...

  20. Surface Dynamic Process Simulation with the Use of Cellular Automata

    International Nuclear Information System (INIS)

    Adamska-Szatko, M.; Bala, J.

    2010-01-01

    Cellular automata are known for many applications, especially for physical and biological simulations. Universal cellular automata can be used for modelling complex natural phenomena. The paper presents simulation of surface dynamic process. Simulation uses 2-dimensional cellular automata algorithm. Modelling and visualisation were created by in-house developed software with standard OpenGL graphic library. (authors)

  1. Poison control services in China

    International Nuclear Information System (INIS)

    Wu Yiqun; Sun Chengye

    2004-01-01

    The following aspects are discussed: the public health problems of acute poisoning in China in recent years; the characteristics of acute poisoning; the negative effects of poison cases on the society and economy. The four stages of development of a poison control system in China are: (1) clinical hospital as the only facility used for detoxification; (2) institutes and hospitals of occupational medicine got involved in the program; (3) the traditional model of poison control changed to the modern National Poison Control Center (NPCC), and its network got established and it began to play a key role; (4) establishment of a multi-disciplinary network for dealing with emergencies in which chemical poison control is an important component. Introduction of the operations of the NPCC: the functions of the center are a 24 h hotline service, clinical consultants service, poison identification and diagnosis, laboratory analysis, education for public, training for physicians, coordination of anti-dotes, and the development of a network of poison control centers for dealing with chemical emergencies. The work practice and achievement of NPCC and its network in the field of poison control during the last 3 years is discussed. Lessons from SARS infection: to extend the network, to strengthen multi-disciplinary cooperation, enhance communication between centers, to pay attention to capacity building, to improve reporting systems, and to share resources

  2. Ciguatera poisoning in Vanuatu.

    Science.gov (United States)

    Goodman, Anna; Williams, Thomas N; Maitland, Kathryn

    2003-02-01

    Ciguatera poisoning is endemic in many tropical and subtropical countries. We conducted a retrospective study of admissions to two hospitals on the islands of Vanuatu in the southwestern Pacific region. We estimated the annual hospital admission rate for fish poisoning to be 65 (95% confidence interval [CI] = 55-75)/100,000 population on the island of Santo and 29 (95% CI = 19-43)/100,000 population on the island of Ambae. Hospital admission was more common in males 20-29 years old. Death was a rare complication. In the face of increases in both tourism and in the global trade in tropical and exotic fish, physicians in both endemic and non-endemic areas should be familiar with the epidemiology and clinical features of this important condition.

  3. Calcium channel blocker poisoning

    Directory of Open Access Journals (Sweden)

    Miran Brvar

    2005-04-01

    Full Text Available Background: Calcium channel blockers act at L-type calcium channels in cardiac and vascular smooth muscles by preventing calcium influx into cells with resultant decrease in vascular tone and cardiac inotropy, chronotropy and dromotropy. Poisoning with calcium channel blockers results in reduced cardiac output, bradycardia, atrioventricular block, hypotension and shock. The findings of hypotension and bradycardia should suggest poisoning with calcium channel blockers.Conclusions: Treatment includes immediate gastric lavage and whole-bowel irrigation in case of ingestion of sustainedrelease products. All patients should receive an activated charcoal orally. Specific treatment includes calcium, glucagone and insulin, which proved especially useful in shocked patients. Supportive care including the use of catecholamines is not always effective. In the setting of failure of pharmacological therapy transvenous pacing, balloon pump and cardiopulmonary by-pass may be necessary.

  4. Neuropsychology of thallium poisoning

    Science.gov (United States)

    McMillan, T; Jacobson, R; Gross, M

    1997-01-01

    Cases of thallium poisoning are rare and neuropsychological assessment has only been reported in detail in one other case. In the case reported here, neuropsychological assessments were carried out three, 12, and 54 months after diagnosis of thallium poisoning in a man who had acutely shown a number of neurological signs including confusion and disorientation and generalised slowing of EEG which was more prominent on the left. Evidence suggested that he had been exposed to thallium over a period of weeks. Neuropsychological assessment indicated an unexpected weakness in verbal abilities which persisted. This finding is consistent with the only other published case report which details neuropsychological effects after a single large dose of thallium and which also found a lateralised impairment.

 PMID:9285467

  5. Small dose... big poison.

    Science.gov (United States)

    Braitberg, George; Oakley, Ed

    2010-11-01

    It is not possible to identify all toxic substances in a single journal article. However, there are some exposures that in small doses are potentially fatal. Many of these exposures are particularly toxic to children. Using data from poison control centres, it is possible to recognise this group of exposures. This article provides information to assist the general practitioner to identify potential toxic substance exposures in children. In this article the authors report the signs and symptoms of toxic exposures and identify the time of onset. Where clear recommendations on the period of observation and known fatal dose are available, these are provided. We do not discuss management or disposition, and advise readers to contact the Poison Information Service or a toxicologist for this advice.

  6. The esa earth explorer land surface processes and interactions mission

    Science.gov (United States)

    Labandibar, Jean-Yves; Jubineau, Franck; Silvestrin, Pierluigi; Del Bello, Umberto

    2017-11-01

    The European Space Agency (ESA) is defining candidate missions for Earth Observation. In the class of the Earth Explorer missions, dedicated to research and pre-operational demonstration, the Land Surface Processes and Interactions Mission (LSPIM) will acquire the accurate quantitative measurements needed to improve our understanding of the nature and evolution of biosphere-atmosphere interactions and to contribute significantly to a solution of the scaling problems for energy, water and carbon fluxes at the Earth's surface. The mission is intended to provide detailed observations of the surface of the Earth and to collect data related to ecosystem processes and radiation balance. It is also intended to address a range of issues important for environmental monitoring, renewable resources assessment and climate models. The mission involves a dedicated maneuvering satellite which provides multi-directional observations for systematic measurement of Land Surface BRDF (BiDirectional Reflectance Distribution Function) of selected sites on Earth. The satellite carries an optical payload : PRISM (Processes Research by an Imaging Space Mission), a multispectral imager providing reasonably high spatial resolution images (50 m over 50 km swath) in the whole optical spectral domain (from 450 nm to 2.35 μm with a resolution close to 10 nm, and two thermal bands from 8.1 to 9.1 μm). This paper presents the results of the Phase A study awarded by ESA, led by ALCATEL Space Industries and concerning the design of LSPIM.

  7. Lead poisoning in mink

    Energy Technology Data Exchange (ETDEWEB)

    Purdy, J G

    1962-03-01

    This paper describes a case of lead poisoning in minks. The mink were housed in pens which had been painted with a bridge paint containing lead. They had chewed on the pen and ingested the paint. The animals that did not die were moved to new pens, and vitamin D and calcium gluconate were added to their diets. In three days, a marked improvement was seen in the food and water consumption, and convolutions became less frequent.

  8. Ethylene glycol poisoning

    African Journals Online (AJOL)

    Ethylene glycol poisoning. A 22-year-old male presented to the emergency centre after drinking 300 ml of antifreeze. Clinical examination was unremarkable except for a respiratory rate of 28 bpm, GCS of 9 and slight nystagmus. Arterial blood gas revealed: pH 7.167, pCO2. 3.01 kPa, pO2 13.0 kPa (on room air), HCO3-.

  9. Antidotes for Cyanide Poisoning

    Science.gov (United States)

    2013-01-01

    treatment, six task forces formulated recom- mendations for a national structure of prehospital EM by family physicians, ambulance nurses , and hospital...competencies between ambulance nurses and prehospital physicians. Eur J Emerg Med 2011; 18:322 327. Antidotes for cyanide poisoning Vikhyat S. Bebarta...the study model (limited to 60 min after the start of cyanide infusion) and the hemodynamic parameters as end points, instead of long-term sequelae

  10. Lead Poison Detection

    Science.gov (United States)

    1976-01-01

    With NASA contracts, Whittaker Corporations Space Science division has developed an electro-optical instrument to mass screen for lead poisoning. Device is portable and detects protoporphyrin in whole blood. Free corpuscular porphyrins occur as an early effect of lead ingestion. Also detects lead in urine used to confirm blood tests. Test is inexpensive and can be applied by relatively unskilled personnel. Similar Whittaker fluorometry device called "drug screen" can measure morphine and quinine in urine much faster and cheaper than other methods.

  11. Integrated system of production information processing for surface mines

    Energy Technology Data Exchange (ETDEWEB)

    Li, K.; Wang, S.; Zeng, Z.; Wei, J.; Ren, Z. [China University of Mining and Technology, Xuzhou (China). Dept of Mining Engineering

    2000-09-01

    Based on the concept of geological statistic, mathematical program, condition simulation, system engineering, and the features and duties of each main department in surface mine production, an integrated system for surface mine production information was studied systematically and developed by using the technology of data warehousing, CAD, object-oriented and system integration, which leads to the systematizing and automating of the information management, data processing, optimization computing and plotting. In this paper, its overall object, system design, structure and functions and some key techniques were described. 2 refs., 3 figs.

  12. Electronic dissipation processes during chemical reactions on surfaces

    CERN Document Server

    Stella, Kevin

    2012-01-01

    Hauptbeschreibung Every day in our life is larded with a huge number of chemical reactions on surfaces. Some reactions occur immediately, for others an activation energy has to be supplied. Thus it happens that though a reaction should thermodynamically run off, it is kinetically hindered. Meaning the partners react only to the thermodynamically more stable product state within a mentionable time if the activation energy of the reaction is supplied. With the help of catalysts the activation energy of a reaction can be lowered. Such catalytic processes on surfaces are widely used in industry. A

  13. Paraquat poisoning in the dog

    International Nuclear Information System (INIS)

    O'Sullivan, S.P.

    1989-01-01

    Recovery from paraquat poisoning in the dog is rare. This is a report of a case of recovery from confirmed paraquat poisoning in a clinical setting. The dog exhibited the usual signs of paraquat poisoning. The diagnosis was confirmed on toxicological analysis of urine using an ion exchange technique. The dog was treated with frusemide, nicotinamide, corticosteroids, α-tocopherol, vitamin A, etamiphylline camsylate and ampicillin. He recovered after seven weeks of intensive therapy. Alternative treatments are discussed

  14. Chelation Therapy for Mercury Poisoning

    OpenAIRE

    Rong Guan; Han Dai

    2009-01-01

    Chelation therapy has been the major treatment for heavy metal poisoning. Various chelating agents have been developed and tested for treatment of heavy metal intoxications, including mercury poisoning. It has been clearly shown that chelating agents could rescue the toxicity caused by heavy metal intoxication, but the potential preventive role of chelating agents against heavy metal poisoning has not been explored much. Recent paper by Siddiqi and colleagues has suggested a protective role o...

  15. Mechanical and tribological properties of ion beam-processed surfaces

    International Nuclear Information System (INIS)

    Kodali, P.

    1998-01-01

    The intent of this work was to broaden the applications of well-established surface modification techniques and to elucidate the various wear mechanisms that occur in sliding contact of ion-beam processed surfaces. The investigation included characterization and evaluation of coatings and modified surfaces synthesized by three surface engineering methods; namely, beam-line ion implantation, plasma-source ion implantation, and DC magnetron sputtering. Correlation among measured properties such as surface hardness, fracture toughness, and wear behavior was also examined. This dissertation focused on the following areas of research: (1) investigating the mechanical and tribological properties of mixed implantation of carbon and nitrogen into single crystal silicon by beam-line implantation; (2) characterizing the mechanical and tribological properties of diamond-like carbon (DLC) coatings processed by plasma source ion implantation; and (3) developing and evaluating metastable boron-carbon-nitrogen (BCN) compound coatings for mechanical and tribological properties. The surface hardness of a mixed carbon-nitrogen implant sample improved significantly compared to the unimplanted sample. However, the enhancement in the wear factor of this sample was found to be less significant than carbon-implanted samples. The presence of nitrogen might be responsible for the degraded wear behavior since nitrogen-implantation alone resulted in no improvement in the wear factor. DLC coatings have low friction, low wear factor, and high hardness. The fracture toughness of DLC coatings has been estimated for the first time. The wear mechanism in DLC coatings investigated with a ruby slider under a contact stress of 1 GPa was determined to be plastic deformation. The preliminary data on metastable BCN compound coatings indicated high friction, low wear factor, and high hardness

  16. Is Your Child Safe from Lead Poisoning?

    Centers for Disease Control (CDC) Podcasts

    In this podcast, Dr. Mary Jean Brown, chief of CDC's Lead Poisoning and Prevention Program, discusses the importance of testing children for lead poisoning, who should be tested, and what parents can do to prevent lead poisoning.

  17. Surface processes during purification of InP quantum dots

    Directory of Open Access Journals (Sweden)

    Natalia Mordvinova

    2014-08-01

    Full Text Available Recently, a new simple and fast method for the synthesis of InP quantum dots by using phosphine as phosphorous precursor and myristic acid as surface stabilizer was reported. Purification after synthesis is necessary to obtain samples with good optical properties. Two methods of purification were compared and the surface processes which occur during purification were studied. Traditional precipitation with acetone is accompanied by a small increase in photoluminescence. It occurs that during the purification the hydrolysis of the indium precursor takes place, which leads to a better surface passivation. The electrophoretic purification technique does not increase luminescence efficiency but yields very pure quantum dots in only a few minutes. Additionally, the formation of In(OH3 during the low temperature synthesis was explained. Purification of quantum dots is a very significant part of postsynthetical treatment that determines the properties of the material. But this subject is not sufficiently discussed in the literature. The paper is devoted to the processes that occur at the surface of quantum dots during purification. A new method of purification, electrophoresis, is investigated and described in particular.

  18. Application of Anodization Process for Cast Aluminium Surface Properties Enhancement

    Directory of Open Access Journals (Sweden)

    Włodarczyk-Fligier A.

    2016-09-01

    Full Text Available An huge interest is observed in last years in metal matrix composite, mostly light metal based, which have found their applications in many industry branches, among others in the aircraft industry, automotive-, and armaments ones, as well as in electrical engineering and electronics, where one of the most important issue is related to the corrosion resistance, especially on the surface layer of the used aluminium alloys. This elaboration presents the influence of ceramic phase on the corrosion resistance, quality of the surface layer its thickness and structure of an anodic layer formed on aluminium alloys. As test materials it was applied the aluminium alloys Al-Si-Cu and Al-Cu-Mg, for which heat treatment processes and corrosion tests were carried out. It was presented herein grindability test results and metallographic examination, as well. Hardness of the treated alloys with those ones subjected to corrosion process were compared.

  19. Estimation of surface absorptivity in laser surface heating process with experimental data

    International Nuclear Information System (INIS)

    Chen, H-T; Wu, X-Y

    2006-01-01

    This study applies a hybrid technique of the Laplace transform and finite-difference methods in conjunction with the least-squares method and experimental temperature data inside the test material to predict the unknown surface temperature, heat flux and absorptivity for various surface conditions in the laser surface heating process. In this study, the functional form of the surface temperature is unknown a priori and is assumed to be a function of time before performing the inverse calculation. In addition, the whole time domain is divided into several analysis sub-time intervals and then these unknown estimates on each analysis interval can be predicted. In order to show the accuracy of the present inverse method, comparisons are made among the present estimates, direct results and previous results, showing that the present estimates agree with the direct results for the simulated problem. However, the present estimates of the surface absorptivity deviate slightly from previous estimated results under the assumption of constant thermal properties. The effect of the surface conditions on the surface absorptivity and temperature is not negligible

  20. Probing Interfacial Processes on Graphene Surface by Mass Detection

    Science.gov (United States)

    Kakenov, Nurbek; Kocabas, Coskun

    2013-03-01

    In this work we studied the mass density of graphene, probed interfacial processes on graphene surface and examined the formation of graphene oxide by mass detection. The graphene layers were synthesized by chemical vapor deposition method on copper foils and transfer-printed on a quartz crystal microbalance (QCM). The mass density of single layer graphene was measured by investigating the mechanical resonance of the QCM. Moreover, we extended the developed technique to probe the binding dynamics of proteins on the surface of graphene, were able to obtain nonspecific binding constant of BSA protein of graphene surface in aqueous solution. The time trace of resonance signal showed that the BSA molecules rapidly saturated by filling the available binding sites on graphene surface. Furthermore, we monitored oxidation of graphene surface under oxygen plasma by tracing the changes of interfacial mass of the graphene controlled by the shifts in Raman spectra. Three regimes were observed the formation of graphene oxide which increases the interfacial mass, the release of carbon dioxide and the removal of small graphene/graphene oxide flakes. Scientific and Technological Research Council of Turkey (TUBITAK) grant no. 110T304, 109T209, Marie Curie International Reintegration Grant (IRG) grant no 256458, Turkish Academy of Science (TUBA-Gebip).

  1. The power of poison: pesticide poisoning of Africa's wildlife.

    Science.gov (United States)

    Ogada, Darcy L

    2014-08-01

    Poisons have long been used to kill wildlife throughout the world. An evolution has occurred from the use of plant- and animal-based toxins to synthetic pesticides to kill wildlife, a method that is silent, cheap, easy, and effective. The use of pesticides to poison wildlife began in southern Africa, and predator populations were widely targeted and eliminated. A steep increase has recently been observed in the intensity of wildlife poisonings, with corresponding population declines. However, the majority of poisonings go unreported. Under national laws, it is illegal to hunt wildlife using poisons in 83% of African countries. Pesticide regulations are inadequate, and enforcement of existing legislation is poor. Few countries have forensic field protocols, and most lack storage and testing facilities. Methods used to poison wildlife include baiting carcasses, soaking grains in pesticide solution, mixing pesticides to form salt licks, and tainting waterholes. Carbofuran is the most widely abused pesticide in Africa. Common reasons for poisoning are control of damage-causing animals, harvesting fish and bushmeat, harvesting animals for traditional medicine, poaching for wildlife products, and killing wildlife sentinels (e.g., vultures because their aerial circling alerts authorities to poachers' activities). Populations of scavengers, particularly vultures, have been decimated by poisoning. Recommendations include banning pesticides, improving pesticide regulations and controlling distribution, better enforcement and stiffer penalties for offenders, increasing international support and awareness, and developing regional pesticide centers. © 2014 New York Academy of Sciences.

  2. Diagnosis of acute poisoning | Tygerberg Poison Information Centre ...

    African Journals Online (AJOL)

    Continuing Medical Education. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 21, No 8 (2003) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. Diagnosis of acute poisoning. - Tygerberg Poison ...

  3. CIGUATERA POISONING: PACIFIC DISEASE, FOODBORNE POISONING FROM FISH IN WARM SEAS AND OCEANS. Review

    Directory of Open Access Journals (Sweden)

    Snezha Zlateva

    2017-02-01

    for months and years, there is a possibility that every medic can encounter its unusual symptoms, requiring specific treatment. The following toxins cause the poisoning: ciguatoxin, meitotoxin, ostreotoxin, domoic acid and some other unspecified toxins. They are lipid soluble, thermo stable and cannot be decomposed by culinary processing. These toxins have neurotoxic, cardiotoxic, hemolytic properties and cause diarrheic syndrome. Clinical presentation is characterized by average latent period of 12 hours after the consummation, vomiting and diarrhea next 24 hours and neurological symptoms that appear at the beginning of the poisoning with paresthesias along the body, changing feeling of hot and cold, strong myalgia. Disturbances in cardiac rhythm and conduction, strong dehydration or shock are possible in severe cases. Light cases pass over in several days, but, more often the poisoning has a chronic course – from 3-4 months to 1 year, with prevalence of neurologic symptoms: myalgia, paresthesias, skin itching with scratches, depression. The management is not specific and includes stomach lavage with activated charcoal, fluids replacement during the first 24 hours, corticosteroids, antiallergics, high doses of vitamins from group B (Vit. B1, Vit. B6, Vit. B12, mannitol IV, nootropic medicaments, antidepressants and other symptomatic medicaments. The prophylaxis is done by examining every fish with specific test for detecting ciguateratoxin.

  4. Detection of cracks on concrete surfaces by hyperspectral image processing

    Science.gov (United States)

    Santos, Bruno O.; Valença, Jonatas; Júlio, Eduardo

    2017-06-01

    All large infrastructures worldwide must have a suitable monitoring and maintenance plan, aiming to evaluate their behaviour and predict timely interventions. In the particular case of concrete infrastructures, the detection and characterization of crack patterns is a major indicator of their structural response. In this scope, methods based on image processing have been applied and presented. Usually, methods focus on image binarization followed by applications of mathematical morphology to identify cracks on concrete surface. In most cases, publications are focused on restricted areas of concrete surfaces and in a single crack. On-site, the methods and algorithms have to deal with several factors that interfere with the results, namely dirt and biological colonization. Thus, the automation of a procedure for on-site characterization of crack patterns is of great interest. This advance may result in an effective tool to support maintenance strategies and interventions planning. This paper presents a research based on the analysis and processing of hyper-spectral images for detection and classification of cracks on concrete structures. The objective of the study is to evaluate the applicability of several wavelengths of the electromagnetic spectrum for classification of cracks in concrete surfaces. An image survey considering highly discretized wavelengths between 425 nm and 950 nm was performed on concrete specimens, with bandwidths of 25 nm. The concrete specimens were produced with a crack pattern induced by applying a load with displacement control. The tests were conducted to simulate usual on-site drawbacks. In this context, the surface of the specimen was subjected to biological colonization (leaves and moss). To evaluate the results and enhance crack patterns a clustering method, namely k-means algorithm, is being applied. The research conducted allows to define the suitability of using clustering k-means algorithm combined with hyper-spectral images highly

  5. Novel CNC Grinding Process Control for Nanometric Surface Roughness for Aspheric Space Optical Surfaces

    Directory of Open Access Journals (Sweden)

    Jeong-Yeol Han

    2004-06-01

    Full Text Available Optics fabrication process for precision space optical parts includes bound abrasive grinding, loose abrasive lapping and polishing. The traditional bound abrasive grinding with bronze bond cupped diamond wheel leaves the machine marks of about 20 μm rms in height and the subsurface damage of about 1 μm rms in height to be removed by subsequent loose abrasive lapping. We explored an efficient quantitative control of precision CNC grinding. The machining parameters such as grain size, work-piece rotation speed and feed rate were altered while grinding the work-piece surfaces of 20-100 mm in diameter. The input grinding variables and the resulting surface quality data were used to build grinding prediction models using empirical and multi-variable regression analysis. The effectiveness of such grinding prediction models was then examined by running a series of precision CNC grinding operation with a set of controlled input variables and predicted output surface quality indicators. The experiment achieved the predictability down to ±20 nm in height and the surface roughness down to 36 nm in height. This study contributed to improvement of the process efficiency reaching directly the polishing and figuring process without the need for the loose abrasive lapping stage.

  6. Dynamics of gas-surface interactions atomic-level understanding of scattering processes at surfaces

    CERN Document Server

    Díez Muniño, Ricardo

    2013-01-01

    This book gives a representative survey of the state of the art of research on gas-surface interactions. It provides an overview of the current understanding of gas surface dynamics and, in particular, of the reactive and non-reactive processes of atoms and small molecules at surfaces. Leading scientists in the field, both from the theoretical and the experimental sides, write in this book about their most recent advances. Surface science grew as an interdisciplinary research area over the last decades, mostly because of new experimental technologies (ultra-high vacuum, for instance), as well as because of a novel paradigm, the ‘surface science’ approach. The book describes the second transformation which is now taking place pushed by the availability of powerful quantum-mechanical theoretical methods implemented numerically. In the book, experiment and theory progress hand in hand with an unprecedented degree of accuracy and control. The book presents how modern surface science targets the atomic-level u...

  7. UMTRA Surface Project management action process document: Final. Revision 2

    International Nuclear Information System (INIS)

    1996-06-01

    Title 1 of the UMTRCA authorized the DOE to undertake remedial actions at these designed sites and associated vicinity properties (VP), which contain uranium mill tailings and other residual radioactive materials (RRM) derived from the processing sites. Title 2 of the UMTRCA addresses uranium mill sites that were licensed at the time the UMTRCA was enacted. Cleanup of these Title 2 sites is the responsibility of the licensees. The cleanup of the Title 1 sites has been split into two separate projects: the Surface Project, which deals with the mill buildings, tailings, and contaminated soils at the sites and VPs; and the Ground Water Project, which is limited to the contaminated ground water at the sites. This management action process (MAP) document discusses the Uranium Mill Tailings Remedial Action (UMTRA) Surface Project. Since its inception through March 1996, the Surface Project (hereinafter called the Project) has cleaned up 16 of the 24 designated processing sites and approximately 5,000 VPs, reducing the risk to human health and the environment posed by the uranium mill tailings. Two of the 24 sites, Belfield and Bowman, North Dakota, will not be remediated at the request of the state, reducing the total number of sites to 22. By the start of FY1998, the remaining 6 processing sites and associated VPs will be cleaned up. The remedial action activities to be funded in FY1998 by the FY1998 budget request are remediation of the remaining Grand Junction, Colorado, VPs; closure of the Cheney disposal cell in Grand Junction, Colorado; and preparation of the completion reports for 4 completed sites

  8. UMTRA Surface Project management action process document: Final. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-06-01

    Title 1 of the UMTRCA authorized the DOE to undertake remedial actions at these designed sites and associated vicinity properties (VP), which contain uranium mill tailings and other residual radioactive materials (RRM) derived from the processing sites. Title 2 of the UMTRCA addresses uranium mill sites that were licensed at the time the UMTRCA was enacted. Cleanup of these Title 2 sites is the responsibility of the licensees. The cleanup of the Title 1 sites has been split into two separate projects: the Surface Project, which deals with the mill buildings, tailings, and contaminated soils at the sites and VPs; and the Ground Water Project, which is limited to the contaminated ground water at the sites. This management action process (MAP) document discusses the Uranium Mill Tailings Remedial Action (UMTRA) Surface Project. Since its inception through March 1996, the Surface Project (hereinafter called the Project) has cleaned up 16 of the 24 designated processing sites and approximately 5,000 VPs, reducing the risk to human health and the environment posed by the uranium mill tailings. Two of the 24 sites, Belfield and Bowman, North Dakota, will not be remediated at the request of the state, reducing the total number of sites to 22. By the start of FY1998, the remaining 6 processing sites and associated VPs will be cleaned up. The remedial action activities to be funded in FY1998 by the FY1998 budget request are remediation of the remaining Grand Junction, Colorado, VPs; closure of the Cheney disposal cell in Grand Junction, Colorado; and preparation of the completion reports for 4 completed sites.

  9. Using infrared thermography for understanding and quantifying soil surface processes

    Science.gov (United States)

    de Lima, João L. M. P.

    2017-04-01

    At present, our understanding of the soil hydrologic response is restricted by measurement limitations. In the literature, there have been repeatedly calls for interdisciplinary approaches to expand our knowledge in this field and eventually overcome the limitations that are inherent to conventional measuring techniques used, for example, for tracing water at the basin, hillslope and even field or plot scales. Infrared thermography is a versatile, accurate and fast technique of monitoring surface temperature and has been used in a variety of fields, such as military surveillance, medical diagnosis, industrial processes optimisation, building inspections and agriculture. However, many applications are still to be fully explored. In surface hydrology, it has been successfully employed as a high spatial and temporal resolution non-invasive and non-destructive imaging tool to e.g. access groundwater discharges into waterbodies or quantify thermal heterogeneities of streams. It is believed that thermal infrared imagery can grasp the spatial and temporal variability of many processes at the soil surface. Thermography interprets the heat signals and can provide an attractive view for identifying both areas where water is flowing or has infiltrated more, or accumulated temporarily in depressions or macropores. Therefore, we hope to demonstrate the potential for thermal infrared imagery to indirectly make a quantitative estimation of several hydrologic processes. Applications include: e.g. mapping infiltration, microrelief and macropores; estimating flow velocities; defining sampling strategies; identifying water sources, accumulation of waters or even connectivity. Protocols for the assessment of several hydrologic processes with the help of IR thermography will be briefly explained, presenting some examples from laboratory soil flumes and field.

  10. Influence of surface coverage on the chemical desorption process

    Energy Technology Data Exchange (ETDEWEB)

    Minissale, M.; Dulieu, F., E-mail: francois.dulieu@obspm.fr [LERMA, Université de Cergy Pontoise et Observatoire de Paris, UMR 8112 du CNRS. 5, mail Gay Lussac, 95031 Cergy Pontoise (France)

    2014-07-07

    In cold astrophysical environments, some molecules are observed in the gas phase whereas they should have been depleted, frozen on dust grains. In order to solve this problem, astrochemists have proposed that a fraction of molecules synthesized on the surface of dust grains could desorb just after their formation. Recently the chemical desorption process has been demonstrated experimentally, but the key parameters at play have not yet been fully understood. In this article, we propose a new procedure to analyze the ratio of di-oxygen and ozone synthesized after O atoms adsorption on oxidized graphite. We demonstrate that the chemical desorption efficiency of the two reaction paths (O+O and O+O{sub 2}) is different by one order of magnitude. We show the importance of the surface coverage: for the O+O reaction, the chemical desorption efficiency is close to 80% at zero coverage and tends to zero at one monolayer coverage. The coverage dependence of O+O chemical desorption is proved by varying the amount of pre-adsorbed N{sub 2} on the substrate from 0 to 1.5 ML. Finally, we discuss the relevance of the different physical parameters that could play a role in the chemical desorption process: binding energy, enthalpy of formation, and energy transfer from the new molecule to the surface or to other adsorbates.

  11. Decontamination Efficiency of Fish Bacterial Flora from Processing Surfaces

    Directory of Open Access Journals (Sweden)

    Birna Guðbjörnsdóttir

    2009-01-01

    Full Text Available There are numerous parameters that can influence bacterial decontamination during washing of machinery and equipment in a food processing establishment. Incomplete decontamination of bacteria will increase the risk of biofilm formation and consequently increase the risk of pathogen contamination or prevalence of other undesirable microorganisms such as spoilage bacteria in the processing line. The efficiency of a typical washing protocol has been determined by testing three critical parameters and their effects on bacterial decontamination. Two surface materials (plastic and stainless steel, water temperatures (7 and 25 °C and detergent concentrations (2 and 4 % were used for this purpose in combination with two types of detergents. Biofilm was prepared on the surfaces with undefined bacterial flora obtained from minced cod fillets. The bacterial flora of the biofilm was characterised by cultivation and molecular analysis of 16S rRNA genes. All different combinations of washing protocols tested were able to remove more than 99.9 % of the bacteria in the biofilm and reduce the cell number from 7 to 0 or 2 log units of bacteria/cm2. The results show that it is possible to use less diluted detergents than recommended with comparable success, and it is easier to clean surface material made of stainless steel compared to polyethylene plastic.

  12. Nicotinic plant poisoning.

    Science.gov (United States)

    Schep, Leo J; Slaughter, Robin J; Beasley, D Michael G

    2009-09-01

    A wide range of plants contain nicotinic and nicotinic-like alkaloids. Of this diverse group, those that have been reported to cause human poisoning appear to have similar mechanisms of toxicity and presenting patients therefore have comparable toxidromes. This review describes the taxonomy and principal alkaloids of plants that contain nicotinic and nicotinic-like alkaloids, with particular focus on those that are toxic to humans. The toxicokinetics and mechanisms of toxicity of these alkaloids are reviewed and the clinical features and management of poisoning due to these plants are described. This review was compiled by systematically searching OVID MEDLINE and ISI Web of Science. This identified 9,456 papers, excluding duplicates, all of which were screened. Reviewed plants and their principal alkaloids. Plants containing nicotine and nicotine-like alkaloids that have been reported to be poisonous to humans include Conium maculatum, Nicotiana glauca and Nicotiana tabacum, Laburnum anagyroides, and Caulophyllum thalictroides. They contain the toxic alkaloids nicotine, anabasine, cytisine, n-methylcytisine, coniine, n-methylconiine, and gamma-coniceine. These alkaloids act agonistically at nicotinic-type acetylcholine (cholinergic) receptors (nAChRs). The nicotinic-type acetylcholine receptor can vary both in its subunit composition and in its distribution within the body (the central and autonomic nervous systems, the neuromuscular junctions, and the adrenal medulla). Agonistic interaction at these variable sites may explain why the alkaloids have diverse effects depending on the administered dose and duration of exposure. Nicotine and nicotine-like alkaloids are absorbed readily across all routes of exposure and are rapidly and widely distributed, readily traversing the blood-brain barrier and the placenta, and are freely distributed in breast milk. Metabolism occurs predominantly in the liver followed by rapid renal elimination. Following acute exposure

  13. Cadmium, an environmental poison

    Energy Technology Data Exchange (ETDEWEB)

    Oestergaard, A K

    1974-04-15

    In recent years, industrial employment of cadmium has increased considerably. Cadmium is now present in the environment and has caused acute and chronic poisoning. Inhalation of cadmium vapor or dust causes pulmonary damage while the kidney is the critical organ in absorption of cadmium. The element accumulates in the kidney and causes tubular damage or 200 ppm in the renal cortex. In animal experiments, cadmium may cause raised blood pressure, sterility and malignant tumors. On account of the pronounced tendency of cadmium to accumulate and its toxicity, it is important to trace sources and to reduce exposure of the population. 62 references.

  14. Lead poisoning: The invisible disease

    Science.gov (United States)

    Friend, Milton

    1989-01-01

    Lead poisoning is an intoxication resulting from absorption of hazardous levels of lead into body tissues. Lead pellets from shot shells, when ingested, are the most common source of lead poisoning in migratory birds. Other far less common sources include lead fishing sinkers, mine wastes, paint pigments, bullets, and other lead objects that are swallowed.

  15. Carbon Monoxide Poisoning in Children

    Directory of Open Access Journals (Sweden)

    Chi-Hsiun Cho

    2008-08-01

    Conclusion: Children with CO poisoning had good outcomes in this series. Although improperly vented exhaust from water heaters and house fires were the most common causes, intentional poisoning by parents through charcoal burning was also an important factor. Early identification of DNS risk factors might help to provide better care.

  16. Alcohol Poisoning Deaths PSA (:60)

    Centers for Disease Control (CDC) Podcasts

    This 60 second Public Service Announcement is based on the January 2015 CDC Vital Signs report. In the United States, an average of six people die every day from alcohol poisoning. Learn what you can do to prevent binge drinking and alcohol poisoning.

  17. Copper sulphate poisoning in horses

    Energy Technology Data Exchange (ETDEWEB)

    Bauer, M

    1975-01-01

    In the archives of the Clinic for Internal Diseases of Domestic Animals at the Veterinary Faculty of Zagreb University some thirty cases of horse disease diagnosed as copper sulphate poisoning were noted. The data correspond in many respects to the clinical findings of copper sulphate poisoning in other domestic animals. A series of experimental horse poisonings were undertaken in order to determine the toxicity of copper sulphate. The research results are as follows: Horses are sensitive to copper sulphate. Even a single application of 0.125 g/kg body weight in 1% concentration by means of incubation into the stomach causes stomach and gut disturbances and other poisoning symptoms. Poisoning occurs in two types: acute and chronic. The former appears after one to three applications of copper sulphate solution and is characterized by gastroenteritis, haemolysis, jaundice and haemoglobinuria with signs of consecutive damage of kidney, liver and other organs. The disease, from the first application to death lasts for two weeks. Chronic poisoning is caused by ingestion of dry copper sulphate in food (1% solution dried on hay or clover) for two or more months. There are chronic disturbances of stomach and gut and loss of weight, and consecutive (three to four) haemolytic crises similar to those of acute poisoning. From the beginning of poisoning to death six or more months can elapse.

  18. Extracorporeal treatment for acetaminophen poisoning

    DEFF Research Database (Denmark)

    Gosselin, S; Juurlink, D N; Kielstein, J T

    2014-01-01

    BACKGROUND: The Extracorporeal Treatments in Poisoning (EXTRIP) workgroup was created to provide evidence-based recommendations on the use of extracorporeal treatments (ECTR) in poisoning and the results are presented here for acetaminophen (APAP). METHODS: After a systematic review of the litera...... of NAC has not been definitively demonstrated....

  19. Extracorporeal Treatment for Lithium Poisoning

    DEFF Research Database (Denmark)

    Decker, Brian S; Goldfarb, David S; Dargan, Paul I

    2015-01-01

    The Extracorporeal Treatments in Poisoning Workgroup was created to provide evidence-based recommendations on the use of extracorporeal treatments in poisoning. Here, the EXTRIP workgroup presents its recommendations for lithium poisoning. After a systematic literature search, clinical and toxico......The Extracorporeal Treatments in Poisoning Workgroup was created to provide evidence-based recommendations on the use of extracorporeal treatments in poisoning. Here, the EXTRIP workgroup presents its recommendations for lithium poisoning. After a systematic literature search, clinical...... extraction of patient-level data. The workgroup concluded that lithium is dialyzable (Level of evidence=A) and made the following recommendations: Extracorporeal treatment is recommended in severe lithium poisoning (1D). Extracorporeal treatment is recommended if kidney function is impaired and the [Li...... treatment (1D), but continuous RRT is an acceptable alternative (1D). The workgroup supported the use of extracorporeal treatment in severe lithium poisoning. Clinical decisions on when to use extracorporeal treatment should take into account the [Li(+)], kidney function, pattern of lithium toxicity...

  20. Urbanization Process and Variation of Energy Budget of Land Surfaces

    Directory of Open Access Journals (Sweden)

    Ciro Gardi

    2007-06-01

    Full Text Available Urban areas are increasing at a rate much higher than human population growth in many part of the world; actually more than 73 towns in the world are larger than 1000 km2. The European Environmental Agency indicates an urban area average growth rate, over the last 20 years, of 20%. The urbanization process, and the consequent soil sealing, determines not only the losses of the ecological functions of the soil, but also a variation of the energy budget of land surfaces, that affect the microclimatic conditions (heat islands. The alteration of the energy budget are determined by the variations of albedo and roughness of surfaces, but especially by the net losses of evapotranspirating areas. In the present research we have assessed the variation of Parma territory energy budget, induced by the change in land use over the last 122 years. The urban area increase between 1881 and 2003 was 535%.

  1. Quantification of deexcitation processes for analyzing liquid surfaces

    International Nuclear Information System (INIS)

    Morgner, H.

    2014-01-01

    In the last two decades the mathematical tools for quantitative data evaluation have been developed for several surface spectroscopic techniques like Angular Resolved X-ray Photoelectron Spectroscopy (ARXPS), Neutral Impact Collision Ion Scattering Spectroscopy (NICISS) and Metastable Induced Electron Spectroscopy (MIES). Provided that the experimental data are of good quality, quantitative data processing can add a lot to the information that can be gained from surface spectroscopy. We give a selection of references that contain information on these methods. The emphasis of this contribution aims at providing motivation to apply quantitative data evaluation by presenting a few examples. We try to demonstrate, that careful data evaluation may lead to interesting insight into basic concepts as well as to results that are useful for practical applications

  2. Quantification of deexcitation processes for analyzing liquid surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Morgner, H., E-mail: hmorgner@rz.uni-leipzig.de

    2014-12-01

    In the last two decades the mathematical tools for quantitative data evaluation have been developed for several surface spectroscopic techniques like Angular Resolved X-ray Photoelectron Spectroscopy (ARXPS), Neutral Impact Collision Ion Scattering Spectroscopy (NICISS) and Metastable Induced Electron Spectroscopy (MIES). Provided that the experimental data are of good quality, quantitative data processing can add a lot to the information that can be gained from surface spectroscopy. We give a selection of references that contain information on these methods. The emphasis of this contribution aims at providing motivation to apply quantitative data evaluation by presenting a few examples. We try to demonstrate, that careful data evaluation may lead to interesting insight into basic concepts as well as to results that are useful for practical applications.

  3. Surface hardening of two cast irons by friction stir processing

    International Nuclear Information System (INIS)

    Fujii, Hidetoshi; Kikuchi, Toshifumi; Nogi, Kiyoshi; Yamaguchi, Yasufumi; Kiguchi, Shoji

    2009-01-01

    The Friction Stir Processing (FSP) was applied to the surface hardening of cast irons. Flake graphite cast iron (FC300) and nodular graphite cast iron (FCD700) were used to investigate the validity of this method. The matrices of the FC300 and FC700 cast irons are pearlite. The rotary tool is a 25mm diameter cylindrical tool, and the travelling speed was varied between 50 and 150mm/min in order to control the heat input at the constant rotation speed of 900rpm. As a result, it has been clarified that a Vickers hardness of about 700HV is obtained for both cast irons. It is considered that a very fine martensite structure is formed because the FSP generates the heat very locally, and a very high cooling rate is constantly obtained. When a tool without an umbo (probe) is used, the domain in which graphite is crushed and striated is minimized. This leads to obtaining a much harder sample. The hardness change depends on the size of the martensite, which can be controlled by the process conditions, such as the tool traveling speed and the load. Based on these results, it was clarified that the FSP has many advantages for cast irons, such as a higher hardness and lower distortion. As a result, no post surface heat treatment and no post machining are required to obtain the required hardness, while these processes are generally required when using the traditional methods.

  4. The microfluidic probe: operation and use for localized surface processing.

    Science.gov (United States)

    Perrault, Cecile M; Qasaimeh, Mohammad A; Juncker, David

    2009-06-04

    Microfluidic devices allow assays to be performed using minute amounts of sample and have recently been used to control the microenvironment of cells. Microfluidics is commonly associated with closed microchannels which limit their use to samples that can be introduced, and cultured in the case of cells, within a confined volume. On the other hand, micropipetting system have been used to locally perfuse cells and surfaces, notably using push-pull setups where one pipette acts as source and the other one as sink, but the confinement of the flow is difficult in three dimensions. Furthermore, pipettes are fragile and difficult to position and hence are used in static configuration only. The microfluidic probe (MFP) circumvents the constraints imposed by the construction of closed microfluidic channels and instead of enclosing the sample into the microfluidic system, the microfluidic flow can be directly delivered onto the sample, and scanned across the sample, using the MFP. . The injection and aspiration openings are located within a few tens of micrometers of one another so that a microjet injected into the gap is confined by the hydrodynamic forces of the surrounding liquid and entirely aspirated back into the other opening. The microjet can be flushed across the substrate surface and provides a precise tool for localized deposition/delivery of reagents which can be used over large areas by scanning the probe across the surface. In this video we present the microfluidic probe (MFP). We explain in detail how to assemble the MFP, mount it atop an inverted microscope, and align it relative to the substrate surface, and finally show how to use it to process a substrate surface immersed in a buffer.

  5. Interdependencies of Arctic land surface processes: A uniquely sensitive environment

    Science.gov (United States)

    Bowling, L. C.

    2007-12-01

    The circumpolar arctic drainage basin is composed of several distinct ecoregions including steppe grassland and cropland, boreal forest and tundra. Land surface hydrology throughout this diverse region shares several unique features such as dramatic seasonal runoff differences controlled by snowmelt and ice break-up; the storage of significant portions of annual precipitation as snow and in lakes and wetlands; and the effects of ephemeral and permanently frozen soils. These arctic land processes are delicately balanced with the climate and are therefore important indicators of change. The litany of recently-detected changes in the Arctic includes changes in snow precipitation, trends and seasonal shifts in river discharge, increases and decreases in the extent of surface water, and warming soil temperatures. Although not unique to the arctic, increasing anthropogenic pressures represent an additional element of change in the form of resource extraction, fire threat and reservoir construction. The interdependence of the physical, biological and social systems mean that changes in primary indicators have large implications for land cover, animal populations and the regional carbon balance, all of which have the potential to feed back and induce further change. In fact, the complex relationships between the hydrological processes that make the Artic unique also render observed historical change difficult to interpret and predict, leading to conflicting explanations. For example, a decrease in snow accumulation may provide less insulation to the underlying soil resulting in greater frost development and increased spring runoff. Similarly, melting permafrost and ground ice may lead to ground subsidence and increased surface saturation and methane production, while more complete thaw may enhance drainage and result in drier soil conditions. The threshold nature of phase change around the freezing point makes the system especially sensitive to change. In addition, spatial

  6. Lead poisoning in dogs

    International Nuclear Information System (INIS)

    Zook, B.C.; Carpenter, J.L.; Leeds, E.B.

    1969-01-01

    Lead poisoning was diagnosed and studied in 60 dogs. It was found that lead poisoning is a common disease of young dogs, especially in the summer and fall, and is related to their chewing and eating habits resulting in the ingestion of paint, linoleum, or other lead-containing materials. The signs were characterized by gastrointestinal dysfunction (colic, vomiting, and diarrhea) and nervous disorders (convulsions, hysteria, nervousness, behavioral changes). The blood findings, which the authors consider nearly pathognomonic, consisted of numerous stippled and immature (especially nucleated) erythrocytes in the absence of severe anemia. Protein and casts were frequently found in the urine. Radiography sometimes revealed lead-containing particles in the gastro-intestinal tract, and lead lines were occasionally detected in the metaphysis of long bones in immature dogs. Treatment with calcium ethylenediamine-tetraacetic acid resulted in rapid and often dramatic recoveries in nearly all instances. Removal of lead from the gastrointestinal tract and treatment to relieve pronounced central nervous disorders was sometimes necessary. 40 references, 6 figures, 7 tables

  7. Endosulfan poisoning: An overview.

    Science.gov (United States)

    Menezes, Ritesh G; Qadir, Tooba Fatima; Moin, Ariba; Fatima, Huda; Hussain, Syed Ather; Madadin, Mohammed; Pasha, Syed Bilal; Al Rubaish, Fatima A; Senthilkumaran, S

    2017-10-01

    Endosulfan, an organochlorine (OC) insecticide, is a widely used agricultural pesticide, despite its life threatening toxic effects. In this review, the pharmacokinetics of endosulfan, mechanism of endosulfan toxicity, clinical presentations and management, histopathological findings, and toxicological analysis are described, in addition to its environmental toxicity. The toxic effects of endosulfan can affect many organs and systems presenting in a wide array of signs and symptoms. Although termed a restricted OC-classed pesticide, it continues to be used, especially in the developing world, owing to its beneficial effects on agriculture. Several cases of endosulfan poisoning have been reported from different regions of the world. Whether accidental or intentional, endosulfan ingestion proves to be fatal unless immediate, aggressive treatment is initiated. Management is mainly supportive as no antidote exists for endosulfan poisoning as yet. The use of endosulfan needs to be strictly regulated and eventually banned worldwide altogether to lower the current morbidity and mortality resulting from this pesticide. Additionally, monitoring biological samples, using non-invasive techniques such as breast milk sampling, can provide an effective method of observing the elimination of this environmentally persistent organic pollutant from the general population. Copyright © 2017 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

  8. Organophosphorus poisoning (acute).

    Science.gov (United States)

    Blain, Peter G

    2011-05-17

    Acetylcholinesterase inhibition by organophosphorus pesticides or organophosphate nerve agents can cause acute parasympathetic system dysfunction, muscle weakness, seizures, coma, and respiratory failure. Prognosis depends on the dose and relative toxicity of the specific compound, as well as pharmacokinetic factors. We conducted a systematic review and aimed to answer the following clinical question: What are the effects of treatments for acute organophosphorus poisoning? We searched: Medline, Embase, The Cochrane Library, and other important databases up to April 2010 (Clinical Evidence reviews are updated periodically; please check our website for the most up-to-date version of this review). We included harms alerts from relevant organisations such as the US Food and Drug Administration (FDA) and the UK Medicines and Healthcare products Regulatory Agency (MHRA). We found 62 systematic reviews, RCTs, or observational studies that met our inclusion criteria. We performed a GRADE evaluation of the quality of evidence for interventions. In this systematic review we present information relating to the effectiveness and safety of the following interventions: activated charcoal (single or multiple doses), alpha(2) adrenergic receptor agonists, atropine, benzodiazepines, butyrylcholinesterase replacement therapy, cathartics, extracorporeal clearance, gastric lavage, glycopyrronium bromide (glycopyrrolate), ipecacuanha (ipecac), magnesium sulphate, milk or other home remedy immediately after ingestion, N-methyl-D-aspartate receptor antagonists, organophosphorus hydrolases, oximes, removing contaminated clothes and washing the poisoned person, and sodium bicarbonate.

  9. [Arsenic - Poison or medicine?].

    Science.gov (United States)

    Kulik-Kupka, Karolina; Koszowska, Aneta; Brończyk-Puzoń, Anna; Nowak, Justyna; Gwizdek, Katarzyna; Zubelewicz-Szkodzińska, Barbara

    2016-01-01

    Arsenic (As) is commonly known as a poison. Only a few people know that As has also been widely used in medicine. In the past years As and its compounds were used as a medicine for the treatment of such diseases as diabetes, psoriasis, syphilis, skin ulcers and joint diseases. Nowadays As is also used especially in the treatment of patients with acute promyelocytic leukemia. The International Agency for Research on Cancer (IARC) has recognized arsenic as an element with carcinogenic effect evidenced by epidemiological studies, but as previously mentioned it is also used in the treatment of neoplastic diseases. This underlines the specificity of the arsenic effects. Arsenic occurs widely in the natural environment, for example, it is present in soil and water, which contributes to its migration to food products. Long exposure to this element may lead to liver damages and also to changes in myocardium. Bearing in mind that such serious health problems can occur, monitoring of the As presence in the environmental media plays a very important role. In addition, the occupational risk of As exposure in the workplace should be identified and checked. Also the standards for As presence in food should be established. This paper presents a review of the 2015 publications based on the Medical database like PubMed and Polish Medical Bibliography. It includes the most important information about arsenic in both forms, poison and medicine. This work is available in Open Access model and licensed under a CC BY-NC 3.0 PL license.

  10. Surfaces: processing, coating, decontamination, pollution, etc. Surface mastering to prevent component corrosion; Surfaces: traitement, revetements, decontamination, pollution, etc. Maitrise de la surface pour prevenir la corrosion des composants

    Energy Technology Data Exchange (ETDEWEB)

    Foucault, M. [Departement Corrosion Chimie, AREVA Centre Technique, BP 181, 71205 Le Creusot (France)

    2012-07-01

    In the primary and secondary circuits of nuclear Pressurized Water Reactors, AREVA uses several nickel-based alloys or austenitic stainless steels for the manufacture of safety components. The experience feedback of the last twenty years allows us to point out the major role hold by the component surface state in their life duration. In this paper, we present four examples of problem encountered and solved by a surface study and the definition and implementation of processes for the surface control of the repaired components. Then, we propose some ideas about the present needs in term of analysis means to improve the surface knowledge and control of the manufactured components. (author)

  11. Surface photo reaction processes using synchrotron radiation; Hoshako reiki ni yoru hyomenko hanno process

    Energy Technology Data Exchange (ETDEWEB)

    Imaizumi, Y. [Tohoku University, Sendai (Japan). Institute for Materials Research; Yoshigoe, A. [Toyohashi University of Technology, Aichi (Japan); Urisu, T. [Toyohashi University of Technology, Aichi (Japan). Institute for Molecular Science

    1997-08-20

    This paper introduces the surface photo reaction processes using synchrotron radiation, and its application. A synchrotron radiation process using soft X-rays contained in electron synchrotron radiated light as an excited light source has a possibility of high-resolution processing because of its short wave length. The radiated light can excite efficiently the electronic state of a substance, and can induce a variety of photochemical reactions. In addition, it can excite inner shell electrons efficiently. In the aspect of its application, it has been found that, if radiated light is irradiated on surfaces of solids under fluorine-based reaction gas or Cl2, the surfaces can be etched. This technology is utilized practically. With regard to radiated light excited CVD process, it may be said that anything that can be deposited by the ordinary plasma CVD process can be deposited. Its application to epitaxial crystal growth may be said a nano processing application in thickness direction, such as forming an ultra-lattice structure, the application being subjected to expectation. In micromachine fabricating technologies, a possibility is searched on application of a photo reaction process of the radiated light. 5 refs., 6 figs.

  12. Textural Analysis of Fatique Crack Surfaces: Image Pre-processing

    Directory of Open Access Journals (Sweden)

    H. Lauschmann

    2000-01-01

    Full Text Available For the fatique crack history reconstitution, new methods of quantitative microfractography are beeing developed based on the image processing and textural analysis. SEM magnifications between micro- and macrofractography are used. Two image pre-processing operatins were suggested and proved to prepare the crack surface images for analytical treatment: 1. Normalization is used to transform the image to a stationary form. Compared to the generally used equalization, it conserves the shape of brightness distribution and saves the character of the texture. 2. Binarization is used to transform the grayscale image to a system of thick fibres. An objective criterion for the threshold brightness value was found as that resulting into the maximum number of objects. Both methods were succesfully applied together with the following textural analysis.

  13. Dual Electrolytic Plasma Processing for Steel Surface Cleaning and Passivation

    Science.gov (United States)

    Yang, L.; Zhang, P.; Shi, J.; Liang, J.; Tian, W. B.; Zhang, Y. M.; Sun, Z. M.

    2017-10-01

    To remove the rust on rebars and passivate the fresh surfaces, electrodes reversing electrolytic plasma processing (EPP) was proposed and conducted in a 10 wt.% Na2CO3 aqueous solution. The morphology and the composition of the surface were investigated by SEM and XPS. Experimental results show that the rust on the surface was removed effectively by cathode EPP, and a passive film containing Cr2O3 was achieved by the succeeding anode EPP treatment, by a simple operation of reversing the bias. The corrosion resistance was evaluated in a 3.5 wt.% NaCl aqueous solution using an electrochemical workstation. In comparison, the corrosion resistance was improved by the succeeding anode EPP treatment, which is evidenced by a positive shift of the open-circuit potential, an increase in the electrochemical impedance representing the inner layer by 76.8% and the decrease in the corrosion current density by 49.6%. This is an effective and environment-friendly technique to clean and passivate rebars and similar steel materials.

  14. Land use and surface process domains on alpine hillslopes

    Science.gov (United States)

    Kuhn, Nikolaus J.; Caviezel, Chatrina; Hunziker, Matthias

    2015-04-01

    Shrubs and trees are generally considered to protect hillslopes from erosion. As a consequence, shrub encroachment on mountain pastures after abandoning grazing is not considered a threat to soils. However, the abandonment of mown or grazed grasslands causes a shift in vegetation composition and thus a change in landscape ecology and geomorphology. On many alpine slopes, current changes in land use and vegetation cover are accompanied by climate change, potentially generating a new geomorphic regime. Most of the debate focuses on the effect of land abandonment on water erosion rates. Generally, an established perennial vegetation cover improves the mechanical anchoring of the soil and the regulation of the soil water budget, including runoff generation and erosion. However, changing vegetation composition affects many other above- and below-ground properties like root density, -diversity and -geometry, soil structure, pore volume and acidity. Each combination of these properties can lead to a distinct scenario of dominating surface processes, often not reflected by common erosion risk assessment procedures. The study of soil properties along a chronosequence of green alder (alnusviridis) encroachment on the Unteralptal in central Switzerland reveals that shrub encroachment changes soil and vegetation properties towards an increase of resistance to run-off related erosion processes, but a decrease of slope stability against shallow landslides. The latter are a particular threat because of the currently increasing frequency of slide-triggering high magnitude rainfalls. The potential change of process domain on alpine pastures highlights the need for a careful use of erosion models when assessing future land use and climate scenarios. In mountains, but also other intensively managed agricultural landscapes, risk assessment without the appropriate reflection on the shifting relevance of surface processes carries the risk of missing future threats to environmental

  15. Investigation of ammonia air-surface exchange processes in a ...

    Science.gov (United States)

    Recent assessments of atmospheric deposition in North America note the increasing importance of reduced (NHx = NH3 + NH4+) forms of nitrogen (N) relative to oxidized forms. This shift in in the composition of inorganic nitrogen deposition has both ecological and policy implications. Deposition budgets developed from inferential models applied at the landscape scale, as well as regional and global chemical transport models, indicate that NH3 dry deposition contributes a significant portion of inorganic N deposition in many areas. However, the bidirectional NH3 flux algorithms employed in these models have not been extensively evaluated for North American conditions (e.g, atmospheric chemistry, meteorology, biogeochemistry). Further understanding of the processes controlling NH3 air-surface exchange in natural systems is critically needed. Based on preliminary results from the Southern Appalachian Nitrogen Deposition Study (SANDS), this presentation examines processes of NH3 air-surface exchange in a deciduous montane forest at the Coweeta Hydrologic Laboratory in western North Carolina. A combination of measurements and modeling are used to investigate net fluxes of NH3 above the forest and sources and sinks of NH3 within the canopy and forest floor. Measurements of biogeochemical NH4+ pools are used to characterize emission potential and NH3 compensation points of canopy foliage (i.e., green vegetation), leaf litter, and soil and their relation to NH3 fluxes

  16. Process for growing a film epitaxially upon an oxide surface and structures formed with the process

    Science.gov (United States)

    McKee, Rodney A.; Walker, Frederick J.

    1995-01-01

    A process and structure wherein a film comprised of a perovskite or a spinel is built epitaxially upon a surface, such as an alkaline earth oxide surface, involves the epitaxial build up of alternating constituent metal oxide planes of the perovskite or spinel. The first layer of metal oxide built upon the surface includes a metal element which provides a small cation in the crystalline structure of the perovskite or spinel, and the second layer of metal oxide built upon the surface includes a metal element which provides a large cation in the crystalline structure of the perovskite or spinel. The layering sequence involved in the film build up reduces problems which would otherwise result from the interfacial electrostatics at the first atomic layers, and these oxides can be stabilized as commensurate thin films at a unit cell thickness or grown with high crystal quality to thicknesses of 0.5-0.7 .mu.m for optical device applications.

  17. 49 CFR 172.554 - POISON placard.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false POISON placard. 172.554 Section 172.554... SECURITY PLANS Placarding § 172.554 POISON placard. (a) Except for size and color, the POISON placard must be as follows: EC02MR91.057 (b) In addition to complying with § 172.519, the background on the POISON...

  18. MarsSI: Martian surface data processing information system

    Science.gov (United States)

    Quantin-Nataf, C.; Lozac'h, L.; Thollot, P.; Loizeau, D.; Bultel, B.; Fernando, J.; Allemand, P.; Dubuffet, F.; Poulet, F.; Ody, A.; Clenet, H.; Leyrat, C.; Harrisson, S.

    2018-01-01

    MarsSI (Acronym for Mars System of Information, https://emars.univ-lyon1.fr/MarsSI/, is a web Geographic Information System application which helps managing and processing martian orbital data. The MarsSI facility is part of the web portal called PSUP (Planetary SUrface Portal) developed by the Observatories of Paris Sud (OSUPS) and Lyon (OSUL) to provide users with efficient and easy access to data products dedicated to the martian surface. The portal proposes 1) the management and processing of data thanks to MarsSI and 2) the visualization and merging of high level (imagery, spectral, and topographic) products and catalogs via a web-based user interface (MarsVisu). The portal PSUP as well as the facility MarsVisu is detailed in a companion paper (Poulet et al., 2018). The purpose of this paper is to describe the facility MarsSI. From this application, users are able to easily and rapidly select observations, process raw data via automatic pipelines, and get back final products which can be visualized under Geographic Information Systems. Moreover, MarsSI also contains an automatic stereo-restitution pipeline in order to produce Digital Terrain Models (DTM) on demand from HiRISE (High Resolution Imaging Science Experiment) or CTX (Context Camera) pair-images. This application is funded by the European Union's Seventh Framework Programme (FP7/2007-2013) (ERC project eMars, No. 280168) and has been developed in the scope of Mars, but the design is applicable to any other planetary body of the solar system.

  19. Experimental lead poisoning in chickens

    Energy Technology Data Exchange (ETDEWEB)

    Silven, L.

    1967-01-01

    Poisoning of water fowl due to the intake of lead shot is not rare in the USA. In order to study this kind of poisoning more closely domestic fowl were given varying amounts of lead shot and lead powder. This treatment did not provoke any symptoms of poisoning. Chemical analyses of different organs, muscles, skeleton and eggs yielded low lead values. It is concluded that the low toxicity of lead administered as lead shot to the domestic fowl is due to a low absorption rate from the gastro-intestinal tract.

  20. Alcohol Withdrawal Mimicking Organophosphate Poisoning

    Directory of Open Access Journals (Sweden)

    Nezihat Rana Disel

    2014-02-01

    Full Text Available Organophosphates, which can cause occupational poisoning due to inappropriate personal protective measures, are widely used insecticides in agricultural regions of southern Turkey. Therefore, the classical clinical findings of this cholinergic poisoning are myosis, excessive secretions, bradicardia and fasciculations are easy to be recognized by local medical stuff. Diseases and conditions related to alcoholism such as mental and social impairments, coma, toxicity, withdrawal, and delirium are frequent causes of emergency visits of chronic alcoholic patients. Here we present a case diagnosed and treated as organophosphate poisoning although it was an alcohol withdrawal in the beginning and became delirium tremens, due to similar symptoms.

  1. [Ciguatera fish poisoning].

    Science.gov (United States)

    Oehler, Erwan; Bouchut, Jérémie

    2014-09-01

    Ciguatera, an ichtyosarcotoxism linked to the consumption of usually healthy coral fish is a common poisoning in the Pacific, Caribbean and Indian Ocean where it is endemic. However, increased tourism and commercial transportation of tropical fish for consumption make it an unexceptional intoxication in countries away from its endemic area. Environmental stresses such as climate changes also contribute to the expansion of its geographical area. The non-specific clinical symptomatology is characterized by the occurrence of gastrointestinal, cardiovascular, nervous and general signs few hours after eating a ciguatoxic fish. The diagnosis is clinical and relatively easy in endemic areas but much less for physicians who are rarely confronted with, which is a source of prolonged diagnostic delays and a significant increase in spending. Treatment of ciguatera is symptomatic but new treatments, still experimental, give a real hope for the future. Copyright © 2014 Elsevier Masson SAS. All rights reserved.

  2. Occult carbon monoxide poisoning.

    Science.gov (United States)

    Kirkpatrick, J N

    1987-01-01

    A syndrome of headache, fatigue, dizziness, paresthesias, chest pain, palpitations and visual disturbances was associated with chronic occult carbon monoxide exposure in 26 patients in a primary care setting. A causal association was supported by finding a source of carbon monoxide in a patient's home, workplace or vehicle; results of screening tests that ruled out other illnesses; an abnormally high carboxyhemoglobin level in 11 of 14 patients tested, and abatement or resolution of symptoms when the source of carbon monoxide was removed. Exposed household pets provided an important clue to the diagnosis in some cases. Recurrent occult carbon monoxide poisoning may be a frequently overlooked cause of persistent or recurrent headache, fatigue, dizziness, paresthesias, abdominal pain, diarrhea and unusual spells.

  3. Fatal aluminium phosphide poisoning

    Directory of Open Access Journals (Sweden)

    Meena Mahesh Chand

    2015-06-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide which is commonly used for grain preservation. AlP has currently aroused interest with a rising number of cases in the past four decades due to increased use for agricultural and non-agricultural purposes. Its easy availability in the markets has increased also its misuse for committing suicide. Phosphine inhibits cellular oxygen utilization and can induce lipid peroxidation. Poisoning with AlP has often occurred in attempts to commit suicide, and that more often in adults than in teenagers. This is a case of suicidal consumption of aluminium phosphide by a 32-year-old young medical anesthetist. Toxicological analyses detected aluminium phosphide. We believe that free access of celphos tablets in grain markets should be prohibited by law.

  4. Using poison center exposure calls to predict methadone poisoning deaths.

    Directory of Open Access Journals (Sweden)

    Nabarun Dasgupta

    Full Text Available PURPOSE: There are more drug overdose deaths in the Untied States than motor vehicle fatalities. Yet the US vital statistics reporting system is of limited value because the data are delayed by four years. Poison centers report data within an hour of the event, but previous studies suggested a small proportion of poisoning deaths are reported to poison centers (PC. In an era of improved electronic surveillance capabilities, exposure calls to PCs may be an alternate indicator of trends in overdose mortality. METHODS: We used PC call counts for methadone that were reported to the Researched Abuse, Diversion and Addiction-Related Surveillance (RADARS® System in 2006 and 2007. US death certificate data were used to identify deaths due to methadone. Linear regression was used to quantify the relationship of deaths and poison center calls. RESULTS: Compared to decedents, poison center callers tended to be younger, more often female, at home and less likely to require medical attention. A strong association was found with PC calls and methadone mortality (b=0.88, se=0.42, t=9.5, df=1, p<0.0001, R(2 =0.77. These findings were robust to large changes in a sensitivity analysis assessing the impact of underreporting of methadone overdose deaths. CONCLUSIONS: Our results suggest that calls to poison centers for methadone are correlated with poisoning mortality as identified on death certificates. Calls received by poison centers may be used for timely surveillance of mortality due to methadone. In the midst of the prescription opioid overdose epidemic, electronic surveillance tools that report in real-time are powerful public health tools.

  5. High resistance to sulfur poisoning of Ni with copper skin under electric field

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Xiaopei; Zhang, Yanxing [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China); Yang, Zongxian, E-mail: yzx@henannu.edu.cn [College of Physics and Materials Science, Henan Normal University, Xinxiang, Henan 453007 (China); Collaborative Innovation Center of Nano Functional Materials and Applications, Kaifeng, Henan Province (China)

    2017-02-12

    The effects of sulfur poisoning on the (1 0 0), (1 1 0) and (1 1 1) surfaces of pure Ni and Cu/Ni alloy are studied in consideration of the effect of electric field. The effects of Cu dopants on the S poisoning characteristics are analyzed by the means of the density functional theory results in combination with thermodynamics data using the ab initio atomistic thermodynamic method. When the Cu concentration increases to 50% on the surface layer of the Cu/Ni alloy, the (1 1 0) surface becomes the most vulnerable to the sulfur poisoning. Ni with a copper skin can mostly decrease the sulfur poisoning effect. Especially under the electric field of 1.0 V/Å, the sulfur adsorption and phase transition temperature can be further reduced. We therefore propose that Ni surfaces with copper skin can be very effective to improve the resistance to sulfur poisoning of the Ni anode under high electric field. - Highlights: • The electric field and Cu dopant effects on S poisoning feature of Ni are analyzed. • The present of large electric field can enhance S tolerance. • Cu dopant concentration affect the surface electronic structure of Ni. • 100% Cu doping on surface Ni layer can mostly decrease the sulfur poison.

  6. Optimization of vibratory welding process parameters using response surface methodology

    Energy Technology Data Exchange (ETDEWEB)

    Singh, Pravin Kumar; Kumar, S. Deepak; Patel, D.; Prasad, S. B. [National Institute of Technology Jamshedpur, Jharkhand (India)

    2017-05-15

    The current investigation was carried out to study the effect of vibratory welding technique on mechanical properties of 6 mm thick butt welded mild steel plates. A new concept of vibratory welding technique has been designed and developed which is capable to transfer vibrations, having resonance frequency of 300 Hz, into the molten weld pool before it solidifies during the Shielded metal arc welding (SMAW) process. The important process parameters of vibratory welding technique namely welding current, welding speed and frequency of the vibrations induced in molten weld pool were optimized using Taguchi’s analysis and Response surface methodology (RSM). The effect of process parameters on tensile strength and hardness were evaluated using optimization techniques. Applying RSM, the effect of vibratory welding parameters on tensile strength and hardness were obtained through two separate regression equations. Results showed that, the most influencing factor for the desired tensile strength and hardness is frequency at its resonance value, i.e. 300 Hz. The micro-hardness and microstructures of the vibratory welded joints were studied in detail and compared with those of conventional SMAW joints. Comparatively, uniform and fine grain structure has been found in vibratory welded joints.

  7. Broad beam ion sources and some surface processes

    International Nuclear Information System (INIS)

    Neumann, H.; Scholze, F.; Tarz, M.; Schindler, A.; Wiese, R.; Nestler, M.; Blum, T.

    2005-01-01

    Modern broad-beam multi-aperture ion sources are widely used in material and surface technology applications. Customizing the generated ion beam properties (i. e. the ion current density profile) for specific demands of the application is a main challenge in the improvement of the ion beam technologies. First we introduce ion sources based on different plasma excitation principles shortly. An overview of source plasma and ion beam measurement methods deliver input data for modelling methods. This beam profile modelling using numerical trajectory codes and the validation of the results by Faraday cup measurements as a basis for ion beam profile design are described. Furthermore possibilities for ex situ and in situ beam profile control are demonstrated, like a special method for in situ control of a linear ion source beam profile, a grid modification for circular beam profile design and a cluster principle for broad beam sources. By means of these methods, the beam shape may be adapted to specific technological demands. Examples of broad beam source application in ion beam figuring of optical surfaces, modification of stainless steel, photo voltaic processes and deposition of EUVL-multilayer stacks are finally presented. (Author)

  8. Use of Radiotracers to Study Surface Water Processes

    International Nuclear Information System (INIS)

    2015-03-01

    This publication represents a sound knowledge base for the conduct of radiotracer studies in the environment, with papers on radiotracer methodology, radiation protection and regulation, data analysis and modelling. Environmental case histories from five Member States - Australia, Brazil, France, the Republic of Korea and Sweden - provide information on conducting studies involving he use of radioactive tracers. These case histories are not meant as guidelines for preparing a field study but can rather serve as examples of the type, caution and extent of work involved in environmental studies using radiotracers. This publication can provide guidance for conducting potential future training events in the use of radioactive traces in the environment and can serve as a key reference to all concerned directly with surface water processes

  9. Multi-surface topography targeted plateau honing for the processing of cylinder liner surfaces of automotive engines

    Science.gov (United States)

    Lawrence, K. Deepak; Ramamoorthy, B.

    2016-03-01

    Cylinder bores of automotive engines are 'engineered' surfaces that are processed using multi-stage honing process to generate multiple layers of micro geometry for meeting the different functional requirements of the piston assembly system. The final processed surfaces should comply with several surface topographic specifications that are relevant for the good tribological performance of the engine. Selection of the process parameters in three stages of honing to obtain multiple surface topographic characteristics simultaneously within the specification tolerance is an important module of the process planning and is often posed as a challenging task for the process engineers. This paper presents a strategy by combining the robust process design and gray-relational analysis to evolve the operating levels of honing process parameters in rough, finish and plateau honing stages targeting to meet multiple surface topographic specifications on the final running surface of the cylinder bores. Honing experiments were conducted in three stages namely rough, finish and plateau honing on cast iron cylinder liners by varying four honing process parameters such as rotational speed, oscillatory speed, pressure and honing time. Abbott-Firestone curve based functional parameters (Rk, Rpk, Rvk, Mr1 and Mr2) coupled with mean roughness depth (Rz, DIN/ISO) and honing angle were measured and identified as the surface quality performance targets to be achieved. The experimental results have shown that the proposed approach is effective to generate cylinder liner surface that would simultaneously meet the explicit surface topographic specifications currently practiced by the industry.

  10. Mercury pOIsonIng

    African Journals Online (AJOL)

    A case of mercury poisoning is reported and clinical observations of 6 .... fish ingested and occupational exposure. .... exposed to mercury as a result of inadequate industrial safety standards, and ... WHO Tech Rep Ser 1980; No. 674: 102-115.

  11. Neurotoxic shellfish poisoning: A review

    NARCIS (Netherlands)

    Apeldoorn ME van; Egmond HP van; Speijers GJA; CSR; ARO

    2001-01-01

    This review contains information on the neurotoxic shellfish poisoning (NSP) syndrome and the provoking toxins called brevetoxins, produced by the dinoflagellate Gymnodinium breve. Data on chemical structures and detection methods for brevetoxins, sources for brevetoxins, marine organisms associated

  12. Neurotoxic shellfish poisoning: A review

    NARCIS (Netherlands)

    Apeldoorn ME van; Egmond HP van; Speijers GJA; CSR; ARO

    2001-01-01

    Dit literatuuroverzicht bevat informatie betreffende het "neurotoxic shellfish poisoning" (NSP) syndroom en de veroorzakende toxines, nl.de brevetoxines, welke geproduceerd worden door de dinoflagellaat Gymnodinium breve. Chemische structuren en detectie-methodes van de brevetoxines,

  13. RPV housed ATWS poison tank

    International Nuclear Information System (INIS)

    Oosterkamp, W.J.

    1992-01-01

    This patent describes a boiling water reactor (BWR) wherein housed within a reactor pressure vessel (RPV) is a nuclear core and an upper steam dome connected to a steam outlet in the RPV. The improvement comprises: a pressurized vessel disposed in the steam dome containing a neutron poison effective for inactivating the core and a first line for assaying the poison which first line runs to the outside of the RPV, the vessel being vented to the steam dome to pressurize the poison contained therein, the vessel being connected by a second line terminating beneath the core, the second line containing a valve which is actuable to release the poison through the line upon its actuation

  14. Grass and weed killer poisoning

    Science.gov (United States)

    ... medlineplus.gov/ency/article/002838.htm Grass and weed killer poisoning To use the sharing features on this page, please enable JavaScript. Many weed killers contain dangerous chemicals that are harmful if ...

  15. The poisoning of NRX pile

    International Nuclear Information System (INIS)

    Watson, W.H.

    1959-09-01

    The experimental methods used to study the poisoning of the NRX reactor are described and the operation of the reactor in relation to these methods is reviewed for the period February to September 1948. (author)

  16. Alcohol Poisoning Deaths PSA (:60)

    Centers for Disease Control (CDC) Podcasts

    2015-01-06

    This 60 second Public Service Announcement is based on the January 2015 CDC Vital Signs report. In the United States, an average of six people die every day from alcohol poisoning. Learn what you can do to prevent binge drinking and alcohol poisoning.  Created: 1/6/2015 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 1/6/2015.

  17. [A case of Veratrum poisoning].

    Science.gov (United States)

    Festa, M; Andreetto, B; Ballaris, M A; Panio, A; Piervittori, R

    1996-05-01

    A poisoning from a Veratrum album infusion mistaken for Gentiana lutea is described. Confusion between these two plants can easily occur because they are very similar, although flowers and disposition of leaves allow their botanic determinat: V. album leaves are alternate and flowers are white, while G. lutea leaves are opposite and flowers yellow. The poisoning involves gastrointestinal (pyrosis, vomiting) and cardiocirculatory systems (bradyarrhy-thmias, A-V dissociation, vasodilatation) Atropine is the drug of choice.

  18. Acute selenium poisoning in lambs

    Energy Technology Data Exchange (ETDEWEB)

    Gabbedy, B J; Dickson, J

    1969-10-01

    An outbreak of sodium selenite poisoning is reported in which 180 of 190 six-weeks-old lambs died. The estimated dose rate of the selenium was 6.4 mg/kg body weight. Liver concentrations of selenium at the time of poisoning averaged 64 ppM and 15 days later liver and kidney concentrations of selenium averaged 26 ppM and 7.4 ppM respectively.

  19. Scombroid fish poisoning: an overlooked marine food poisoning.

    Science.gov (United States)

    Wu, M L; Yang, C C; Yang, G Y; Ger, J; Deng, J F

    1997-08-01

    Scombroid fish poisoning is a food-borne chemical intoxication caused by certain spoiled fish that contain a large amount of histamine and some biogenic diamines. It has gradually become a world-wide medical problem and probably is the most common cause of fish poisoning. As the data on the incidents of scombroid fish poisoning in Taiwan remains scarce, we report 2 incidents of scombroid fish poisoning in Northern Taiwan. We collected data of the 2 outbreaks of suspected fish poisoning which were reported to us in 1996. An epidemiological investigation was undertaken. Questionnaire interviews were given to persons who ate lunch in the same cafeteria in outbreak 2. The leftover fish were sent for species identification and toxin analysis. The first incident involving 4 women occurred in March 1996. All cases experienced flush, dizziness, blurred vision and skin rashes after eating lunch. A non-scombroid fish of Makaira with histamine levels as high as 84.13 mg/100 g flesh was implicated in this incident. In August 1996, another incident involving some cases who ate lunch at the same cafeteria were investigated. A total of 146 questionnaires were distributed with a return of 132 questionnaires (90.4%). Fifty-five employees reported positive signs or symptoms; 48 persons who ate fish and 7 women who did not eat fish were ill. Fish was the only food associated with the illness with an attack rate of 73.8% (p < 0.001). The incriminated fish was later identified as a scombroid fish of Euthynnus with a histamine content of 271.9 mg/100 g flesh in 1 leftover piece and 118.5 mg/100 g flesh in another piece. Most cases in these 2 outbreaks received treatment with antihistamines and had rapid and complete recovery. The diagnosis of scombroid fish poisoning could be misdiagnosed as food allergy or bacterial food poisoning if physicians are not aware of such poisoning. The nonspecific but characteristic symptomatology of histamine food poisoning and previous consumption of fish

  20. Gestalten of today: early processing of visual contours and surfaces.

    Science.gov (United States)

    Kovács, I

    1996-12-01

    While much is known about the specialized, parallel processing streams of low-level vision that extract primary visual cues, there is only limited knowledge about the dynamic interactions between them. How are the fragments, caught by local analyzers, assembled together to provide us with a unified percept? How are local discontinuities in texture, motion or depth evaluated with respect to object boundaries and surface properties? These questions are presented within the framework of orientation-specific spatial interactions of early vision. Key observations of psychophysics, anatomy and neurophysiology on interactions of various spatial and temporal ranges are reviewed. Aspects of the functional architecture and possible neural substrates of local orientation-specific interactions are discussed, underlining their role in the integration of information across the visual field, and particularly in contour integration. Examples are provided demonstrating that global context, such as contour closure and figure-ground assignment, affects these local interactions. It is illustrated that figure-ground assignment is realized early in visual processing, and that the pattern of early interactions also brings about an effective and sparse coding of visual shape. Finally, it is concluded that the underlying functional architecture is not only dynamic and context dependent, but the pattern of connectivity depends as much on past experience as on actual stimulation.

  1. Process for integrating surface drainage constraints on mine planning

    Energy Technology Data Exchange (ETDEWEB)

    Sawatsky, L.F; Ade, F.L.; McDonald, D.M.; Pullman, B.J. [Golder Associates Ltd., Calgary, AB (Canada)

    2009-07-01

    Surface drainage for mine closures must be considered during all phases of mine planning and design in order to minimize environmental impacts and reduce costs. This paper discussed methods of integrating mine drainage criteria and associated mine planning constraints into the mine planning process. Drainage constraints included stream diversions; fish compensation channels; collection receptacles for the re-use of process water; separation of closed circuit water from fresh water; and the provision of storage ponds. The geomorphic approach replicated the ability of natural channels to respond to local and regional changes in hydrology as well as channel disturbances from extreme flood events, sedimentation, debris, ice jams, and beaver activity. The approach was designed to enable a sustainable system and provide conveyance capacity for extreme floods without spillage to adjacent watersheds. Channel dimensions, bank and bed materials, sediment loads, bed material supplies and the hydrologic conditions of the analogue stream were considered. Hydrologic analyses were conducted to determine design flood flow. Channel routes, valley slopes, sinuosity, width, and depth were established. It was concluded that by incorporating the geomorphic technique, mine operators and designers can construct self-sustaining drainage systems that require little or no maintenance in the long-term. 7 refs.

  2. [The comparative analysis of acute poisoning characteristics between cities and rural areas in Guangxi].

    Science.gov (United States)

    Jiang, Dong-fang; Liu, Qing-hua

    2012-06-01

    To compare the acute-poisoning characteristics between city and rural areas of Guangxi Province in order to provide clinical data for the formation of treatment strategies of acute poisoning in Guangxi. Data of acute poisoning patients as treated in 36 municipal and 12 county hospitals, and also 15 rural clinics in 11 cities of Guangxi during 2005 to 2009 were collected and analyzed according to poisoning population, poisoning site, poisoning process, and poisoning degree. By analysing 3678 and 2153 cases of acute poisoning patients in rural and urban areas, the gender [χ (2) = 5.53, P old (11.17% vs. 8.69%), farmers by occupation (74.84% vs. 2.79%), home (80.64% vs. 78.07%), sites of labor (11.83% vs. 3.07%) and other sites (4.08% vs. 2.97%), and the chief causes were professional (3.10% vs. 1.30%), taken by mistake (21.85% vs. 20.91%), homicide (0.30% vs. 0.28%), and suicide (39.07% vs. 18.77%), and by pesticide (60.94% vs. 12.13%), plant (7.08% vs. 2.88%) and animal poisons (7.73% vs. 6.56%), belonging to severe poisoning (25.86% vs. 19.04%) were higher than those in town. In the town, poisoning occurred predominantly in female (55.09% vs. 51.90%), age below 19 years old (23.78% vs. 19.44%), unemployed (33.35% vs. 13.76%), student (17.53% vs. 8.43%), industrial workers (31.95% vs. 2.69%), executives (10.84% vs. 0.22%) and other professional (3.53% vs. 0.05%); occurred in schools (8.78% vs. 0.82%), restaurants (5.48% vs. 1.55%), place of entertainment (1.63% vs. 1.09%), by accidental (52.23% vs. 31.27%), therapeutic (4.46% vs. 2.56%), and other reasons (2.04% vs. 1.85%); by chemicals (33.19% vs. 8.55%), medicines (24.31% vs. 9.12%), and other types of poison (20.92% vs. 6.59%); light and medium degree of poisoning (44.87% vs. 41.22%, 36.09% vs. 32.93%) were higher than those in rural areas. Regarding the acute poisoning in Guangxi, the composition of population, the poisoning sites and causes, the types of poisons, the poisoning degree are distinctly different

  3. What is the definition of a poisoning?

    Science.gov (United States)

    Uges, D R

    2001-03-01

    New insights in medicine and acceptable treatments necessitates an adjustment of the existing definition of clinical or forensic poisoning to: 'An individual's medical or social unacceptable condition as a consequence of being under influence of an exogenous substance in a dose too high for the person concerned'. For medical and legal purposes it is important to know how the victim became poisoned. In general, there are three ways of causing medical poisoning: accidental poisoning, including iatrogenic poisoning, experimental and intentional poisoning. Nowadays iatrogenic intoxication, poisoning caused by the Münchhausen's syndrome (by proxy) and experimental poisoning (designer drugs) have a major place in contemporary toxicology. Although some toxicologists use the word 'intoxication' only overdoses with central effects, in this article 'intoxication' and 'poisoning' are considered to be synonymous.

  4. Surface passivation process of compound semiconductor material using UV photosulfidation

    Science.gov (United States)

    Ashby, Carol I. H.

    1995-01-01

    A method for passivating compound semiconductor surfaces by photolytically disrupting molecular sulfur vapor with ultraviolet radiation to form reactive sulfur which then reacts with and passivates the surface of compound semiconductors.

  5. Shewanella putrefaciens adhesion and biofilm formation on food processing surfaces

    DEFF Research Database (Denmark)

    Bagge, Dorthe; Hjelm, M.; Johansen, C.

    2001-01-01

    Laboratory model systems were developed for studying Shewanella putrefaciens adhesion and biofilm formation under batch and flow conditions. S. putrefaciens plays a major role in food spoilage and may cause microbially induced corrosion on steel surfaces. S. putrefaciens bacteria suspended in buf...... from surfaces, and indirect conductometry and found this combination sufficient to quantify bacteria on surfaces...

  6. Sabatier Catalyst Poisoning Investigation

    Science.gov (United States)

    Nallette, Tim; Perry, Jay; Abney, Morgan; Knox, Jim; Goldblatt, Loel

    2013-01-01

    The Carbon Dioxide Reduction Assembly (CRA) on the International Space Station (ISS) has been operational since 2010. The CRA uses a Sabatier reactor to produce water and methane by reaction of the metabolic CO2 scrubbed from the cabin air and the hydrogen byproduct from the water electrolysis system used for metabolic oxygen generation. Incorporating the CRA into the overall air revitalization system has facilitated life support system loop closure on the ISS reducing resupply logistics and thereby enhancing longer term missions. The CRA utilizes CO2 which has been adsorbed in a 5A molecular sieve within the Carbon Dioxide Removal Assembly, CDRA. There is a potential of compounds with molecular dimensions similar to, or less than CO2 to also be adsorbed. In this fashion trace contaminants may be concentrated within the CDRA and subsequently desorbed with the CO2 to the CRA. Currently, there is no provision to remove contaminants prior to entering the Sabatier catalyst bed. The risk associated with this is potential catalyst degradation due to trace organic contaminants in the CRA carbon dioxide feed acting as catalyst poisons. To better understand this risk, United Technologies Aerospace System (UTAS) has teamed with MSFC to investigate the impact of various trace contaminants on the CRA catalyst performance at relative ISS cabin air concentrations and at about 200/400 times of ISS concentrations, representative of the potential concentrating effect of the CDRA molecular sieve. This paper summarizes our initial assessment results.

  7. Paracetamol (acetaminophen) poisoning.

    Science.gov (United States)

    Park, B Kevin; Dear, James W; Antoine, Daniel J

    2015-10-19

    Paracetamol directly causes around 150 deaths per year in UK. We conducted a systematic overview, aiming to answer the following clinical question: What are the effects of treatments for acute paracetamol poisoning? We searched: Medline, Embase, The Cochrane Library, and other important databases up to October 2014 (Clinical Evidence overviews are updated periodically; please check our website for the most up-to-date version of this overview). At this update, searching of electronic databases retrieved 127 studies. After deduplication and removal of conference abstracts, 64 records were screened for inclusion in the overview. Appraisal of titles and abstracts led to the exclusion of 46 studies and the further review of 18 full publications. Of the 18 full articles evaluated, one systematic review was updated and one RCT was added at this update. In addition, two systematic reviews and three RCTs not meeting our inclusion criteria were added to the Comment sections. We performed a GRADE evaluation for three PICO combinations. In this systematic overview we categorised the efficacy for six interventions, based on information about the effectiveness and safety of activated charcoal (single or multiple dose), gastric lavage, haemodialysis, liver transplant, methionine, and acetylcysteine.

  8. Lead poisoning in calves

    Energy Technology Data Exchange (ETDEWEB)

    Reeves, J E

    1964-01-01

    Over a three-year period a farmer lost seven calves in their second month of age. One year ago a tentative diagnosis of rabies was given and a brain was submitted to the Health of Animals Division for examination. No Negri bodies were found. The owner stated that the calves first appeared listless and later exhibited severe nervous signs. Deaths occurred in from one to 24 hours after onset of signs. Appetite and bowel movements were normal. There was no increase in temperature. The calf would lie quietly for an interval, then rise, run down the alley, press against a wall, and go into a convulsion. It acted as if it were in severe pain and during one of the intermittent convulsions, it jumped over a three-foot partition. This calf was sent to the Regional Veterinary Laboratory at Brighton for necropsy. The calf had been dead for 72 hours when submitted to the laboratory. The only gross findings were of mild pleurisy and hemorrhage on the kidney. A tentative diagnosis of lead poisoning was offered and specimens sent to the Division of Pharmacology and Toxicology, Ontario Veterinary College.

  9. Acoustic emission-based in-process monitoring of surface generation in robot-assisted polishing

    DEFF Research Database (Denmark)

    Pilny, Lukas; Bissacco, Giuliano; De Chiffre, Leonardo

    2016-01-01

    The applicability of acoustic emission (AE) measurements for in-process monitoring of surface generation in the robot-assisted polishing (RAP) was investigated. Surface roughness measurements require interruption of the process, proper surface cleaning and measurements that sometimes necessitate...... automatic detection of optimal process endpoint allow intelligent process control, creating fundamental elements in development of robust fully automated RAP process for its widespread industrial application....... removal of the part from the machine tool. In this study, stabilisation of surface roughness during polishing rotational symmetric surfaces by the RAP process was monitored by AE measurements. An AE sensor was placed on a polishing arm in direct contact with a bonded abrasive polishing tool...

  10. Using OSL dating to quantify rates of Earth surface processes

    Science.gov (United States)

    Rhodes, E. J.; Rittenour, T. M.

    2010-12-01

    In Optically Stimulated Luminescence (OSL), the dating signal is reset when mineral grains are exposed to light or heat, and gradually rebuilds during subsequent burial by interaction with ionising radiation. Quartz and feldspar provide useful OSL signals demonstrating rapid signal reduction in only seconds of light exposure. Age estimates ranging from under 1 year to around 200,000 years can be determined for a wide range of sedimentary contexts, including dunes, marine deposits, fluvial and glacial environments, and recent developments provide the framework for low temperature thermochronometric applications on timescales comparable with rapid climate fluctuations. In this presentation, we explore the range of applications for determining rates of Earth surface processes using OSL. We examine technical limitations, and provide a framework for overcoming current difficulties experienced in several specific regions and contexts. We will focus on OSL dating applications to glacigenic and fluvial records, along with use of the technique in tectonic and paleoseismic contexts. In many ways, these represent the most challenging environments for OSL; rapid high energy deposition is associated with incomplete signal zeroing, and the characteristics of quartz in many of these environments make it difficult to derive precise age estimates using this mineral. We will introduce innovative methods to overcome these limitations, both existing and those under development.

  11. Production method of burnable poison incorporated fuel pellet by coating

    International Nuclear Information System (INIS)

    Naito, Naoyoshi.

    1993-01-01

    A cylindrical member is formed with an organic material which is melted, decomposed or evaporated by heating. Such organic materials include polyethylene and polyvinyl alcohol, for example. A predetermined amount of burnable poisons are homogeneously incorporated in the cylindrical member by a means, such as melting before fabricating it into a cylindrical shape. UO 2 fuel pellets are inserted to the cylindrical member and heated, to scatter only the organic materials, so that non-volatile burnable poisons are homogeneously left on the surface of the pellets. It is preferred that the cylindrical member having pellets inserted therein is inserted to a cladding tube and applied with a heat treatment. With such procedures, a UO 2 pellet is coated with burnable poisons by a convenient and compact device. In addition, grinding step after the coating is unnecessary. (I.N.)

  12. Air plasma processing of poly(methyl methacrylate) micro-beads: Surface characterisations

    International Nuclear Information System (INIS)

    Liu Chaozong; Cui Naiyi; Osbeck, Susan; Liang He

    2012-01-01

    Highlights: ► PMMA micro-beads were processed using a rotary air plasma reactor. ► Surface chemistry and surface texture of PMMA micro-beads were characterised. ► Surface wettability was evaluated using “floating” water contact angle method. ► Surface oxidation and texture changes induced by air plasma attributed to the improvement of surface wettability. - Abstract: This paper reports the surface processing of poly(methyl methacrylate) (PMMA) micro-beads by using a rotary air plasma reactor, and its effects on surface properties. The surface properties, including surface wettability, surface chemistry and textures of the PMMA beads, were characterised. It was observed that the air plasma processing can improve the surface wettability of the PMMA microbeads significantly. A 15 min plasma processing can reduce the surface water contact angle of PMMA beads to about 50° from its original value of 80.3°. This was accompanied by about 8% increase in surface oxygen concentration as confirmed by XPS analysis. The optical profilometry examination revealed the air plasma processing resulted in a rougher surface that has a “delicate” surface texture. It is concluded that the surface chemistry and texture, induced by air plasma processing, co-contributed to the surface wettability improvement of PMMA micro-beads.

  13. Photochemical Transformation Processes in Sunlit Surface Waters (Invited)

    Science.gov (United States)

    Vione, D.

    2013-12-01

    Photochemical reactions are major processes in the transformation of hardly biodegradable xenobiotics in surface waters. They are usually classified into direct photolysis and indirect or sensitised degradation. Direct photolysis requires xenobiotic compounds to absorb sunlight, and to get transformed as a consequence. Sensitised transformation involves reaction with transient species (e.g. °OH, CO3-°, 1O2 and triplet states of chromophoric dissolved organic matter, 3CDOM*), photogenerated by so-called photosensitisers (nitrate, nitrite and CDOM). CDOM is a major photosensitiser: is it on average the main source of °OH (and of CO3-° as a consequence, which is mainly produced upon oxidation by °OH of carbonate and bicarbonate) and the only important source of 1O2 and 3CDOM* [1, 2]. CDOM origin plays a key role in sensitised processes: allochthonous CDOM derived from soil runoff and rich in fulvic and humic substances is usually more photoactive than autochthonous CDOM (produced by in-water biological processes and mainly consisting of protein-like material) or of CDOM derived from atmospheric deposition. An interesting gradual evolution of CDOM origin and photochemistry can be found in mountain lakes across the treeline, which afford a gradual transition of allochthonous- autochtonous - atmopheric CDOM when passing from trees to alpine meadows to exposed rocks [3]. Another important issue is the sites of reactive species photoproduction in CDOM. While there is evidence that smaller molecular weight fractions are more photoactive, some studies have reported considerable 1O2 reactivity in CDOM hydrophobic sites and inside particles [4]. We have recently addressed the problem and found that dissolved species in standard humic acids (hydrodynamic diameter pollutants to be assessed and modelled. For instance, it is possible to predict pollutant half-life times by knowing absorption spectrum, direct photolysis quantum yield and reaction rate constants with °OH, CO3

  14. Electron beam processed plasticized epoxy coatings for surface protection

    International Nuclear Information System (INIS)

    Ibrahim, Mervat S.; Mohamed, Heba A.; Kandile, Nadia G.; Said, Hossam M.; Mohamed, Issa M.

    2011-01-01

    Highlights: · Coating formulations with EA 70%, HD 20%, and castor oil 10% under 1 Mrad pass -1 irradiation dose showed the best adhesion and passed bending tests. · The prepared EP-SF-An adduct improve anti-corrosion properties of coatings without any significant effect on physical, mechanical and chemical properties of the cured film. The optimum amount of aniline adduct as corrosion inhibitor was found to be 0.4 g for 100 g of coating formulation. · The corrosion inhibition efficiency of the prepared adduct competed the commercial efficiency. - Abstract: Epoxy acrylate oligomer (EA) was plasticized by adding different plasticizers such as epoxidized soybean oil, glycerol and castor oil and cured by electron beam (EB). Different irradiation doses (1, 2.5 and 5 Mrad pass -1 ) were used in the curing process. The effect of both different irradiation doses and plasticizers on the end use performance properties of epoxy acrylate coating namely, pencil hardness, bending test, adhesion test, acid and alkali resistance test were studied. It was observed that incorporation of castor oil in epoxy acrylate diluted by 1,6-hexanediol diacrylate (HD) monomer with a ratio (EA 70%, HD 20%, castor oil 10%) under 1 Mrad pass -1 irradiation dose improved the physical, chemical and mechanical properties of cured films than the other plasticizer. Sunflower free fatty acid was epoxidized in situ under well established conditions. The epoxidized sunflower free fatty acids (ESFA) were subjected to react with aniline in sealed ampoules under inert atmosphere at 140 deg. C. The produced adducts were added at different concentrations to epoxy acrylate coatings under certain EB irradiation dose and then evaluated as corrosion inhibitors for carbon steel surfaces in terms of weight loss measurements and corrosion resistance tests. It was found that, addition of 0.4 g of aniline adduct to 100 g epoxy acrylate formula may give the best corrosion protection for carbon steel and compete the

  15. Electrochemical and morphological analyses on the titanium surface modified by shot blasting and anodic oxidation processes

    Energy Technology Data Exchange (ETDEWEB)

    Szesz, Eduardo M., E-mail: eszesz@neoortho.com.br [Neoortho Research Institute, Rua Ângelo Domingos Durigan, 607-Cascatinha, CEP 82025-100 Curitiba, PR (Brazil); Pereira, Bruno L., E-mail: brnl7@hotmail.com [Physics Department, Universidade Federal do Paraná, 81531-980 Curitiba, PR (Brazil); Kuromoto, Neide K., E-mail: kuromoto@fisica.ufpr.br [Physics Department, Universidade Federal do Paraná, 81531-980 Curitiba, PR (Brazil); Marino, Claudia E.B., E-mail: claudiamarino@yahoo.com [Mechanical Engineering Department, Universidade Federal do Paraná, 81531-980 Curitiba, PR (Brazil); Souza, Gelson B. de, E-mail: gelsonbs@uepg.br [Physics Department, Universidade Estadual de Ponta Grossa, 84051-510 Ponta Grossa, PR (Brazil); Soares, Paulo, E-mail: pa.soares@pucpr.br [Mechanical Engineering Department, Pontifícia Universidade Católica do Paraná, 80215-901 Curitiba, PR (Brazil)

    2013-01-01

    In recent years, many surface modification processes have been developed in order to induce the osseointegration on titanium surface and thus to improve the implants' biocompatibility. In this work, Ti surface has been modified by shot blasting followed by anodic oxidation process in order to associate the good surface characteristics of both processes to obtain a rough and porous surface able to promote the titanium surface bioactivity. Commercially pure titanium (grade 2) plates were used on the surface treatments that were as follows: Shot blasting (SB) performed using alumina (Al{sub 2}O{sub 3}) particles, and anodic oxidation (AO) using NaOH electrolyte. The morphology, structural changes and the open-circuit potentials (OCP) of the surfaces were analyzed. It can be observed that an increase on the roughness of the blasted surface and a rough and porous surface happens after the AO process. The anodic film produced is thin and followed the blasted surface topography. It can be observed that there are small pores with regular shape covering the entire surface. X-ray diffraction results showed the presence of the anatase and rutile phases on the blasted and anodized surface after heat treatment at 600 °C/1 h. Concerning electrochemical measurements, when the different samples were submitted to open-circuit conditions in a physiological electrolyte, the protective effect increases with the oxidation process due to the oxide layer. When the surface was blasted, the OCP was more negative when compared with the Ti surface without surface treatments. - Highlights: ► A combination of shot blasting and anodic oxidation surface treatments is proposed. ► Both processes produced an increase in roughness compared to the polished surface. ► The combination of processes produced a rough and porous surface. ► Open circuit results show that the protective effect increases with oxidation process. ► The combination of processes presents the better results in this

  16. Organophosphorus pesticide poisoning : cases and developments

    NARCIS (Netherlands)

    Aardema, H.; Ligtenberg, J. J. M.; Peters-Polman, O. M.; Tulleken, J. E.; Zijlstra, J. G.; Meertens, John H. J. M.

    Self-poisoning with organophosphate pesticides is a major health problem world-wide. Through the inhibition of acetylcholinesterase, organophosphorus poisoning is characterised by the clinical picture of acute cholinergic crisis. Other manifestations are the intermediate neurotoxic syndrome and

  17. Vital Signs-Alcohol Poisoning Deaths

    Centers for Disease Control (CDC) Podcasts

    This podcast is based on the January 2015 CDC Vital Signs report. In the United States, an average of six people die every day from alcohol poisoning. Learn what you can do to prevent binge drinking and alcohol poisoning.

  18. Thin film surface processing by ultrashort laser pulses (USLP)

    NARCIS (Netherlands)

    Scorticati, D.; Skolski, J.Z.P.; Romer, G.R.B.E.; Huis in 't Veld, A.J.; Workum, M.J.; Theelen, M.J.; Zeman, M.

    2012-01-01

    In this work, we studied the feasibility of surface texturing of thin molybdenum layers on a borosilicate glass substrate with Ultra-Short Laser Pulses (USLP). Large areas of regular diffraction gratings were produced consisting of Laserinduced periodic surface structures (LIPSS). A short pulsed

  19. [Ciguatera poisoning in Spanish travellers].

    Science.gov (United States)

    Gascón, Joaquim; Macià, Maria; Oliveira, Inés; Corachán, Manuel

    2003-05-31

    Ciguatera poisoning appears after ingestion of contaminated fish from tropical coral reefs. Due to the diversity of clinical symptoms and the absence of a specific test in humans, the diagnosis is often difficult. A retrospective study of 10 patients consulting for a clinical and epidemiological picture compatible with ciguatera poisoning after a trip to tropical countries between 1993 and 2000. Most infections but one were acquired in the Caribbean area and there were 8 females. Clinical manifestations started within the first 24 hours after fish ingestion. Chief symptoms were diarrhea and nausea, followed by neurological symptoms, mainly limbs paresthesias that persisted for several weeks. The severity of clinical symptoms was variable and not related to age or initial symptoms. Ciguatera poisoning has to be considered in the diagnosis of acute gastroenteritis affecting travellers to tropical areas.

  20. Nitric Acid Poisoning: Case Report

    International Nuclear Information System (INIS)

    Quintero Giraldo, Maria Paulina; Quiceno Calderon, William de Jesus; Melo Arango Catalina

    2011-01-01

    Nitric acid (HNO 3 ) is a corrosive fluid that, when in contact with reducing agents, generates nitrogen oxides that are responsible for inhalation poisoning. We present two cases of poisoning from nitric acid gas inhalation resulting from occupational exposure. Imaging findings were similar in both cases, consistent with adult respiratory distress syndrome (ARDS): bilaterally diffuse alveolar opacities on the chest X-ray and a cobblestone pattern on computed tomography (CT).one of the patients died while the other evolved satisfactorily after treatment with n-acetyl cysteine and mechanical ventilation. The diagnosis of nitric acid poisoning was made on the basis of the history of exposure and the way in which the radiological findings evolved.

  1. 49 CFR 172.430 - POISON label.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false POISON label. 172.430 Section 172.430... SECURITY PLANS Labeling § 172.430 POISON label. (a) Except for size and color, the POISON label must be as follows: EC02MR91.029 (b) In addition to complying with § 172.407, the background on the POISON label must...

  2. American Association of Poison Control Centers

    Science.gov (United States)

    ... add poison control as a contact in your smartphone. Take the pledge! National Poison Prevention Week is March 19-25! Be a part of the conversation by following #PreventPoison and #NPPW2017 on social media, and check out AAPCC's NPPW webpage and press ...

  3. Is Your Child Safe from Lead Poisoning?

    Centers for Disease Control (CDC) Podcasts

    2008-10-02

    In this podcast, Dr. Mary Jean Brown, chief of CDC's Lead Poisoning and Prevention Program, discusses the importance of testing children for lead poisoning, who should be tested, and what parents can do to prevent lead poisoning.  Created: 10/2/2008 by National Center for Environmental Health (NCEH).   Date Released: 10/2/2008.

  4. Is poisoning a problem in South Sudan?

    African Journals Online (AJOL)

    2011-11-04

    Nov 4, 2011 ... (e.g. mesothelioma caused by contact with asbestos). Criminal act of poisoning: e.g. “spiking” of a drink at a party. Poisoning in uganda. When I was working in Uganda I saw several cases of poisoning with organophosphates and was horrified by the mortality. Almost ten years ago, we carried out a simple.

  5. National Poison Prevention Week Promotional Materials.

    Science.gov (United States)

    Poison Prevention Week Council, Washington, DC.

    This collection of materials for parents, early childhood workers, the elderly, and anyone in situations requiring safeguards against poisoning, spans the years 1993 and 1994 and is intended to promote National Poison Prevention Week. The materials included are: (1) the 31-page, illustrated report on National Poison Prevention Week for 1993,…

  6. Extracorporeal Treatment for Metformin Poisoning

    DEFF Research Database (Denmark)

    Calello, Diane P; Liu, Kathleen D; Wiegand, Timothy J

    2015-01-01

    diverse professions, presents its systematic review and clinical recommendations for extracorporeal treatment in metformin poisoning. METHODS: A systematic literature search was performed, data extracted, findings summarized, and structured voting statements developed. A two-round modified Delphi method...... was used to achieve consensus on voting statements and RAND/UCLA Appropriateness Method to quantify disagreement. Anonymized votes and opinions were compiled and discussed. A second vote determined the final recommendations. RESULTS: One hundred seventy-five articles were identified, including 63 deaths...... appears to be amenable to extracorporeal treatments. Despite clinical evidence comprised mostly of case reports and suboptimal toxicokinetic data, the workgroup recommended extracorporeal removal in the case of severe metformin poisoning....

  7. Accidental poisoning with autumn crocus.

    Science.gov (United States)

    Gabrscek, Lucija; Lesnicar, Gorazd; Krivec, Bojan; Voga, Gorazd; Sibanc, Branko; Blatnik, Janja; Jagodic, Boris

    2004-01-01

    We describe a case of a 43-yr-old female with severe multiorgan injury after accidental poisoning with Colchicum autumnale, which was mistaken for wild garlic (Allium ursinum). Both plants grow on damp meadows and can be confused in the spring when both plants have leaves but no blossoms. The autumn crocus contains colchicine, which inhibits cellular division. Treatment consisted of supportive care, antibiotic therapy, and granulocyte-directed growth factor. The patient was discharged from the hospital after three weeks. Three years after recovery from the acute poisoning, the patient continued to complain of muscle weakness and intermittent episodes of hair loss.

  8. Lipid resuscitation in acute poisoning

    DEFF Research Database (Denmark)

    Hoegberg, Lotte C G; Gosselin, Sophie

    2017-01-01

    PURPOSE OF REVIEW: The decision to provide intravenous lipid emulsion (ILE) therapy as a treatment modality for the reversal of various drug toxicity was discovered in the last decade. Numerous publications, in both humans and animals attest to its clinical use, but current supporting evidence...... is inconsistent. RECENT FINDINGS: A recent systematic review reported evidence for benefit of ILE in bupivacaine toxicity. Human randomized trials, large observational studies as well as animal models of orogastric poisoning failed to report a clear benefit of ILE for nonlocal anesthetics poisoning. SUMMARY: ILE...

  9. Improving the work function of the niobium surface of SRF cavities by plasma processing

    Science.gov (United States)

    Tyagi, P. V.; Doleans, M.; Hannah, B.; Afanador, R.; McMahan, C.; Stewart, S.; Mammosser, J.; Howell, M.; Saunders, J.; Degraff, B.; Kim, S.-H.

    2016-04-01

    An in situ plasma processing technique using chemically reactive oxygen plasma to remove hydrocarbons from superconducting radio frequency cavity surfaces at room temperature has been developed at the spallation neutron source, at Oak Ridge National Laboratory. To understand better the interaction between the plasma and niobium surface, surface studies on small samples were performed. In this article, we report the results from those surface studies. The results show that plasma processing removes hydrocarbons from top surface and improves the surface work function by 0.5-1.0 eV. Improving the work function of RF surface of cavities can help to improve their operational performance.

  10. A Rare but Potentially Fatal Poisoning; Aluminum Phosphide Poisoning

    Directory of Open Access Journals (Sweden)

    Orkun Tolunay

    2017-04-01

    Full Text Available Phosphide, a very toxic gas, is used in our country as aluminium phosphide tablets impregnated in clay. It is widely used since it has a very high diffusion capacity, whereby it can eradicate all living creatures in any form of their life cycle and does not leave any remnants in agricultural products. Aluminum phosphide poisoning is among intoxications for which there are still no true antidotes. Mortality rate varies between 30% and 100%. This paper presents a case of aluminum phosphide poisoning caused by the uncompleted suicide attempt. A 14-year-old girl, who swallowed aluminum phosphate tablets, was brought to the emergency department with the complaints of nausea and vomiting. The patient was treated with gastric lavage and activated charcoal. Since the patient ingested a lethal amount of aluminum phosphide, she was referred to the pediatric intensive care unit. The patient was discharged in stable condition after supportive care and monitoring. Specific antidotes are life-saving in poisonings. However, this case was presented to show how general treatment principles and quick access to health services affect the result of treatment. Also, we aimed to highlight the uncontrolled selling of aluminum phosphate, which results in high mortality rates in case of poisoning.

  11. Manufacture of functional surfaces through combined application of tool manufacturing processes and Robot Assisted Polishing

    DEFF Research Database (Denmark)

    Eriksen, Rasmus Solmer; Arentoft, Mogens; Grønbæk, J.

    2012-01-01

    The tool surface topography is often a key parameter in the tribological performance of modern metal forming tools. A new generation of multifunctional surfaces is achieved by combination of conventional tool manufacturing processes with a novel Robot Assisted Polishing process. This novel surface...

  12. Coronal Structures as Tracers of Sub-Surface Processes

    Indian Academy of Sciences (India)

    tribpo

    dramatic differences in appearance and physical processes, all these structures share a common ... mena that indicate a close relationship between coronal and sub-photo- spheric processes. .... 8) maintaining the same chirality. Large scale ...

  13. Interaction of different poisons with MgCl{sub 2}/TiCl{sub 4} based Ziegler-Natta catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Bahri-Laleh, Naeimeh, E-mail: n.bahri@ippi.ac.ir

    2016-08-30

    Highlights: • The interactions between different classes of poison molecules and TiCl{sub 4}/MgCl{sub 2} type Ziegler-Natta catalyst is considered. • Poisons strongly stabilize MgCl{sub 2} crystal surfaces, mostly Ti active center relative to the unpoisoned solid. • Poison molecules decrease catalyst activity by increasing E{sub TS} in olefin polymerization. • Poison molecules do not have significant effect in stereospecifity of ZN catalysts in propylene polymerization. - Abstract: Adsorption of different poison molecules on activated MgCl{sub 2} is investigated within DFT using a cluster model of the MgCl{sub 2} surface with (MgCl{sub 2}){sub 16} formula containing four 4-coordinated and eight 5-coordinated Mg atoms as (110) and (104) surfaces, respectively. Studied poison molecules are chosen as possible impurities in hydrocarbon solvents and monomer feeds and contain water, hydrogensulfide, carbondioxide, molecular oxygen and methanol. First, adsorption of 1–4 molecules of different poisons to the (104) and (110) lateral cuts of MgCl{sub 2}, as well as their adsorption on [MgCl{sub 2}]/TiCl{sub 2}Et active center and AlEt{sub 3} cocatalyst is considered. Results reveal that poisons strongly stabilize both crystal surfaces, mostly Ti active center relative to the unpoisoned solid. Second, energy barrier (E{sub TS}) for ethylene insertion in the presence of different poisons located on the first and second Mg atom relative to the active Ti is calculated. While poison molecule located on the second Mg does not change E{sub TS}, coordination of it into the first Mg atom increases E{sub TS} by 0.9–1.2 kcal mol{sup −1}. In the last part of this manuscript, the stereoselective behavior of active Ti species, with and without poison molecules and external electron donor, is fully explored.

  14. Lunar rock surfaces as detectors of solar processes

    International Nuclear Information System (INIS)

    Hartung, J.B.; Hunter College, New York, NY)

    1980-01-01

    Lunar rock surfaces exposed at or just below the lunar surface are considered as detectors of the solar wind, solar flares and solar-derived magnetic fields through their interactions with galactic cosmic rays. The degradation of the solar detector capabilities of lunar surface rocks by meteoroid impact erosion, accreta deposition, loose dust, and sputtering, amorphous layer formation and accelerated diffusion due to solar particles and illumination is discussed, and it is noted that the complex interactions of factors affecting the outer micron of exposed surface material has so far prevented the development of a satisfactory model for a particle detector on the submicron scale. Methods for the determination of surface exposure ages based on the accumulation of light solar wind noble gases, Fe and Mg, impact craters, solar flare tracks, and cosmogenic Kr isotopes are examined, and the systematic variations in the ages determined by the various clocks are discussed. It is concluded that a means of obtaining satisfactory quantitative rate or flux data has not yet been established

  15. Surface processing with ionized cluster beams: computer simulation

    International Nuclear Information System (INIS)

    Insepov, Z.; Yamada, I.

    1999-01-01

    Molecular Dynamics (MD) and Monte Carlo (MC) models of energetic gas cluster irradiation of a solid surface have been developed to investigate the phenomena of crater formation, sputtering, surface treatment, and the material hardness evaluation by irradiation with cluster ions. Theoretical estimation of crater dimensions formed with Ar gas cluster ion irradiation of different substrates, based on hydrodynamics and MD simulation, are presented. The atomic scale shock waves arising from cluster impact were obtained by calculating the pressure, temperature and mass-velocity of the target atoms. The crater depth is given as a unique 1/3 dependence on the cluster energy and on the cold material Brinell hardness number (BHN). A new 'true material hardness' scale which can be very useful for example for thin film coatings deposited on a soft substrate, is defined. This finding could be used as a new technique for measuring of a material hardness. Evolution of surface morphology under cluster ion irradiation was described by the surface relaxation equation which contains a term of crater formation at cluster impact. The formation of ripples on a surface irradiated with oblique cluster ion beams was predicted. MD and MC models of Decaborane ion (B 10 H 14 ) implantation into Si and the following rapid thermal annealing (RTA) have been developed

  16. Active sites in the alkylation of toluene with methanol : a study by selective acid-base poisoning

    NARCIS (Netherlands)

    Borgna, A.; Sepulveda, J.; Magni, S.I.; Apesteguia, C.R.

    2004-01-01

    Selective acid–base poisoning of the alkylation of toluene with methanol was studied over alkali and alkaline-earth exchanged Y zeolites. Surface acid–base properties of the samples were determined by infrared spectroscopy using carbon dioxide and pyridine as probe molecules. Selective poisoning

  17. Advantages of surface treatment processes by ionic sputtering

    International Nuclear Information System (INIS)

    Gantois, M.

    1976-01-01

    The use of high intensity glow-discharge permits to realize a superficial thermochemical treatment. Ions formed by discharge are accelerated against the surfaces to be treated; by effect of ion bombardment, surfaces get heated and a chemical reaction is developed depending on the composition of the ionized gas. The technique presents advantages, as the potential of the active gas might be freely chosen, and as many gases might be used, the decomposition of gases by pyrolysis and a homogeneous treatment (concerning nature of phases and thickness) all over the surface being not necessary. It is possible to develop layers of various nature, looking for those which offer the best properties to solve a technological problem (wear, friction, fatigue toughness, etc.). Some examples of nitruration, carbonitruration are considered [fr

  18. Pulmonary edema in acute carbon monoxide poisoning

    International Nuclear Information System (INIS)

    Kim, Kun Sang; Chang, Kee Hyun; Lee, Myung Uk

    1974-01-01

    Acute carbon monoxide poisoning has frequently occurred in Korean, because of the coal briquette being widely used as fuel in Korean residences. Carbon monoxide poisoning has been extensively studied, but it has been sparsely reported that pulmonary edema may develop in acute CO poisoning. We have noticed nine cases of pulmonary edema in acute CO poisoning last year. Other possible causes of pulmonary edema could be exclude in all cases but one. The purpose of this paper is to describe nine cases of pulmonary edema complicated in acute CO poisoning and discuss the pathogenesis and the prognosis

  19. Article Commentary: Chelation Therapy for Mercury Poisoning

    Directory of Open Access Journals (Sweden)

    Rong Guan

    2009-01-01

    Full Text Available Chelation therapy has been the major treatment for heavy metal poisoning. Various chelating agents have been developed and tested for treatment of heavy metal intoxications, including mercury poisoning. It has been clearly shown that chelating agents could rescue the toxicity caused by heavy metal intoxication, but the potential preventive role of chelating agents against heavy metal poisoning has not been explored much. Recent paper by Siddiqi and colleagues has suggested a protective role of chelating agents against mercury poisoning, which provides a promising research direction for broader application of chelation therapy in prevention and treatment of mercury poisoning.

  20. Usage of burnable poison on research reactors

    International Nuclear Information System (INIS)

    Villarino, Eduardo Anibal

    2002-01-01

    The fuel assemblies with burnable poison are widely used on power reactors, but there are not commonly used on research reactors. This paper shows a neutronic analysis of the advantages and disadvantages of the burnable poison usage on research reactors. This paper analyses both burnable poison design used on research reactors: Boron on the lateral wall and Cadmium wires. Both designs include a parametric study on the design parameters like the amount and geometry of the burnable poison. This paper presents the design flexibility using burnable poisons, it does not find an optimal or final design, which it will strongly depend on the core characteristics and fuel management strategy. (author)

  1. Pulmonary edema in acute carbon monoxide poisoning

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kun Sang; Chang, Kee Hyun; Lee, Myung Uk [Seoul National University College of Medicine, Seoul (Korea, Republic of)

    1974-10-15

    Acute carbon monoxide poisoning has frequently occurred in Korean, because of the coal briquette being widely used as fuel in Korean residences. Carbon monoxide poisoning has been extensively studied, but it has been sparsely reported that pulmonary edema may develop in acute CO poisoning. We have noticed nine cases of pulmonary edema in acute CO poisoning last year. Other possible causes of pulmonary edema could be exclude in all cases but one. The purpose of this paper is to describe nine cases of pulmonary edema complicated in acute CO poisoning and discuss the pathogenesis and the prognosis.

  2. Upper Meter Processes: Short Wind Waves, Surface Flow, and Micro-Turbulence

    National Research Council Canada - National Science Library

    Jaehne, Bernd

    2000-01-01

    The primary goal of this project was to advance the knowledge of small-scale air-sea interaction processes at the ocean surface, focussing on the dynamics of short waves, the surface flow field and the micro-turbulence...

  3. Shewanella putrefaciens Adhesion and Biofilm Formation on Food Processing Surfaces

    Science.gov (United States)

    Bagge, Dorthe; Hjelm, Mette; Johansen, Charlotte; Huber, Ingrid; Gram, Lone

    2001-01-01

    Laboratory model systems were developed for studying Shewanella putrefaciens adhesion and biofilm formation under batch and flow conditions. S. putrefaciens plays a major role in food spoilage and may cause microbially induced corrosion on steel surfaces. S. putrefaciens bacteria suspended in buffer adhered readily to stainless steel surfaces. Maximum numbers of adherent bacteria per square centimeter were reached in 8 h at 25°C and reflected the cell density in suspension. Numbers of adhering bacteria from a suspension containing 108 CFU/ml were much lower in a laminar flow system (modified Robbins device) (reaching 102 CFU/cm2) than in a batch system (reaching 107 CFU/cm2), and maximum numbers were reached after 24 h. When nutrients were supplied, S. putrefaciens grew in biofilms with layers of bacteria. The rate of biofilm formation and the thickness of the film were not dependent on the availability of carbohydrate (lactate or glucose) or on iron starvation. The number of S. putrefaciens bacteria on the surface was partly influenced by the presence of other bacteria (Pseudomonas fluorescens) which reduced the numbers of S. putrefaciens bacteria in the biofilm. Numbers of bacteria on the surface must be quantified to evaluate the influence of environmental factors on adhesion and biofilm formation. We used a combination of fluorescence microscopy (4′,6′-diamidino-2-phenylindole staining and in situ hybridization, for mixed-culture studies), ultrasonic removal of bacteria from surfaces, and indirect conductometry and found this combination sufficient to quantify bacteria on surfaces. PMID:11319118

  4. Ciguatera fish poisoning: a review

    NARCIS (Netherlands)

    Fouw JC de; Egmond HP van; Speijers GJA; CSR

    2001-01-01

    This review on ciguatera fish poisoning contains information on the ciguatera intoxication syndrome and the provoking ciguatoxins (CTXs) and gambiertoxin-4b (GTX-4B), of which CTX-1 is a major component at the end of food chain (the carnivore fish). Data on chemical structures and detection methods

  5. Lead poisoning from souvenir earthenware.

    Science.gov (United States)

    Hellström-Lindberg, Eva; Björklund, Andreas; Karlson-Stiber, Christine; Harper, Pauline; Seldén, Anders I

    2006-02-01

    A case of massive lead poisoning from juice contained in a Greek earthenware jug as well as six satellite cases of high lead exposure of similar origin is reported. The intoxicated patient was successfully treated with dimercaptosuccinic acid. Ceramic producers should adhere to the longstanding European legislation.

  6. Therapeutic problems in cyanide poisoning

    NARCIS (Netherlands)

    van Heijst, A. N.; Douze, J. M.; van Kesteren, R. G.; van Bergen, J. E.; van Dijk, A.

    1987-01-01

    In three patients with severe acute cyanide poisoning, a cyanosis was observed instead of the bright pink skin coloration often mentioned as a sign in textbooks. Treatment of cardiopulmonary insufficiency is as essential as antidotal therapy and the use of sodium nitrite and 4-DMAP is not without

  7. Lead poisoning in domestic ducks

    Energy Technology Data Exchange (ETDEWEB)

    Rac, R; Crisp, C S

    1954-05-01

    The death of wild ducks, due to the ingestion of lead shop, occurs frequently and is well documented. This paper discusses the death of domestic ducks due to the ingestion of lead. It describes the symptoms, and pathology of the lead poisoning of a clutch of 11 ducklings which were being raised on a farm in Australia. 3 references, 1 table.

  8. Hemodialysis in the Poisoned Patient

    Directory of Open Access Journals (Sweden)

    Megan Boysen-Osborn

    2017-09-01

    Full Text Available Audience: This classic team based learning (cTBL didactic is aimed for emergency medicine residents and fourth year medical students entering emergency medicine. Introduction: Over one million visits per year to United States (US emergency departments (ED are related to poisonings.1 Extracorporeal treatment (ECTR, specifically hemodialysis (HD, is one potential method to enhance elimination of certain drugs and their toxic metabolites.2-12 While HD may be life-saving in certain poisonings, it may have no effect on others and it carries associated risks and costs. It is essential that emergency physicians know the indications for HD in the poisoned patient. This cTBL reviews many poisonings which may be managed by HD. Objectives: By the end of this cTBL, the learner will: 1 recognize laboratory abnormalities related to toxic alcohol ingestion; 2 calculate an anion gap and osmolal gap; 3 know the characteristics of drugs that are good candidates for HD; 4 discuss the management of patients with toxic alcohol ingestions; 5 discuss the management of patients with salicylate overdose; 6 know the indications for HD in patients with overdoses of antiepileptic drugs; 7 discuss the management of patients with lithium toxicity. Method: This didactic session is a cTBL (classic team based learning.

  9. Effect of finishing process on the surface quality of Co-Cr-Mo dental alloys

    Directory of Open Access Journals (Sweden)

    Dorota Klimecka -Tatar

    2016-09-01

    Full Text Available Preparatory procedures for the material have a significant influence on the surface stereometry of the material. This study investigated the effect of the electropolishing process on the surface quality of metallic prosthetic constructions based on Co-Cr-Mo alloys. It has been found that the process of electropolishing prevents to excessive development of the surface of a material and consequently improves surface quality.

  10. Bacterial desorption from food container and food processing surfaces.

    Science.gov (United States)

    McEldowney, S; Fletcher, M

    1988-03-01

    The desorption ofStaphylococcus aureus, Acinetobacter calcoaceticus, and a coryneform from the surfaces of materials used for manufacturing food containers (glass, tin plate, and polypropylene) or postprocess canning factory conveyor belts (stainless steel and nylon) was investigated. The effect of time, pH, temperature, and adsorbed organic layers on desorption was studied.S. aureus did not detach from the substrata at any pH investigated (between pH 5 and 9).A. calcoaceticus and the coryneform in some cases detached, depending upon pH and substratum composition. The degree of bacterial detachment from the substrata was not related to bacterial respiration at experimental pH values. Bacterial desorption was not affected by temperature (4-30°C) nor by an adsorbed layer of peptone and yeast extract on the substrata. The results indicate that bacterial desorption, hence bacterial removal during cleaning or their transfer via liquids flowing over colonized surfaces, is likely to vary with the surface composition and the bacterial species colonizing the surfaces.

  11. Nano surface generation of grinding process using carbon nano tubes

    Indian Academy of Sciences (India)

    Nano surface finish has become an important parameter in the semiconductor, optical, electrical and mechanical industries. The materials used in these industries are classified as difficult to machine materials such as ceramics, glasses and silicon wafers. Machining of these materials up to nano accuracy is a great ...

  12. Influence of surface effects on subsecond processes in liquid metals

    International Nuclear Information System (INIS)

    Tkachenko, S.I.; Vorob'ev, V.S.; Khishchenko, K.V.

    2001-01-01

    Full Text: We discuss a problem of experimental-data interpretation during subsecond measurements of thermophysical properties of matter at high temperatures and pressures. Peculiarity of these measurements is optical opaqueness of matter under interesting conditions (T∼1 eV, ρ∼10 4 kg m -3 ), so only at assuming of bulk specimen uniformity one can obtain a temperature dependencies of the specific properties of matter. Changing circuit current and changing sample geometry we can avoid a development of hydromagnetic instability and decrease a nonuniform heating due to skin effect. As temperature of wire surface reaches the boiling temperature under normal pressure so part of internal energy is lost because of evaporation and surface radiation at high temperature. So one can register a surface temperature and ascribe it to the whole sample bulk. Computer simulation of wire explosion taking into account surface radiation losses was carried out. Typical phase tracks for matter were obtained in both case as in consideration of radiation losses as without it. Comparison of the results with data concerning to isobaric-expansion experiments and semi-empirical multi-phase equation of state were carried out. It was proposed uniformity criterion for investigation of thermophysical properties of liquid metal by subsecond wire explosion. (author)

  13. Earthquake rupture process recreated from a natural fault surface

    Science.gov (United States)

    Parsons, Thomas E.; Minasian, Diane L.

    2015-01-01

    What exactly happens on the rupture surface as an earthquake nucleates, spreads, and stops? We cannot observe this directly, and models depend on assumptions about physical conditions and geometry at depth. We thus measure a natural fault surface and use its 3D coordinates to construct a replica at 0.1 m resolution to obviate geometry uncertainty. We can recreate stick-slip behavior on the resulting finite element model that depends solely on observed fault geometry. We clamp the fault together and apply steady state tectonic stress until seismic slip initiates and terminates. Our recreated M~1 earthquake initiates at contact points where there are steep surface gradients because infinitesimal lateral displacements reduce clamping stress most efficiently there. Unclamping enables accelerating slip to spread across the surface, but the fault soon jams up because its uneven, anisotropic shape begins to juxtapose new high-relief sticking points. These contacts would ultimately need to be sheared off or strongly deformed before another similar earthquake could occur. Our model shows that an important role is played by fault-wall geometry, though we do not include effects of varying fluid pressure or exotic rheologies on the fault surfaces. We extrapolate our results to large fault systems using observed self-similarity properties, and suggest that larger ruptures might begin and end in a similar way, though the scale of geometrical variation in fault shape that can arrest a rupture necessarily scales with magnitude. In other words, fault segmentation may be a magnitude dependent phenomenon and could vary with each subsequent rupture.

  14. Improving the work function of the niobium surface of SRF cavities by plasma processing

    International Nuclear Information System (INIS)

    Tyagi, P.V.; Doleans, M.; Hannah, B.; Afanador, R.; McMahan, C.; Stewart, S.; Mammosser, J.; Howell, M.; Saunders, J.; Degraff, B.; Kim, S.-H.

    2016-01-01

    Highlights: • An in situ plasma processing for SNS SRF cavities has been developed to remove hydrocarbons from cavity surface. • Reactive oxygen plasma is very effective to remove hydrocarbons from niobium top surface. • Reactive oxygen plasma processing increases the work function of niobium surface in the range of 0.5–1.0 eV. • It was observed that hydrocarbons can migrate at plasma cleaned top surface from near surface regions when waiting in vacuum at room temperature. • Multiple cycles of plasma processing with waiting periods in between was found beneficial to mitigate such hydrocarbons migration at plasma cleaned surface. - Abstract: An in situ plasma processing technique using chemically reactive oxygen plasma to remove hydrocarbons from superconducting radio frequency cavity surfaces at room temperature has been developed at the spallation neutron source, at Oak Ridge National Laboratory. To understand better the interaction between the plasma and niobium surface, surface studies on small samples were performed. In this article, we report the results from those surface studies. The results show that plasma processing removes hydrocarbons from top surface and improves the surface work function by 0.5–1.0 eV. Improving the work function of RF surface of cavities can help to improve their operational performance.

  15. Surface enhancement of cold work tool steels by friction stir processing with a pinless tool

    Science.gov (United States)

    Costa, M. I.; Verdera, D.; Vieira, M. T.; Rodrigues, D. M.

    2014-03-01

    The microstructure and mechanical properties of enhanced tool steel (AISI D2) surfaces produced using a friction stir welding (FSW) related procedure, called friction stir processing (FSP), are analysed in this work. The surface of the tool steel samples was processed using a WC-Co pinless tool and varying processing conditions. Microstructural analysis revealed that meanwhile the original substrate structure consisted of a heterogeneous distribution of coarse carbides in a ferritic matrix, the transformed surfaces consisted of very small carbides, homogenously distributed in a ferrite- bainite- martensite matrix. The morphology of the surfaces, as well as its mechanical properties, evaluated by hardness and tensile testing, were found to vary with increasing tool rotation speed. Surface hardness was drastically increased, relative to the initial hardness of bulk steel. This was attributed to ferrite and carbide refinement, as well as to martensite formation during solid state processing. At the highest rotation rates, tool sliding during processing deeply compromised the characteristics of the processed surfaces.

  16. Laser surface processing with controlled nitrogen-argon concentration levels for regulated surface life time

    Science.gov (United States)

    Obeidi, M. Ahmed; McCarthy, E.; Brabazon, D.

    2018-03-01

    Laser surface modification can be used to enhance the mechanical properties of a material, such as hardness, toughness, fatigue strength, and corrosion resistance. Surface nitriding is a widely used thermochemical method of surface modification, in which nitrogen is introduced into a metal or other material at an elevated temperature within a furnace. It is used on parts where there is a need for increased wear resistance, corrosion resistance, fatigue life, and hardness. Laser nitriding is a novel method of nitriding where the surface is heated locally by a laser, either in an atmosphere of nitrogen or with a jet of nitrogen delivered to the laser heated site. It combines the benefits of laser modification with those of nitriding. Recent work on high toughness tool steel samples has shown promising results due to the increased nitrogen gas impingement onto the laser heated region. Increased surface activity and nitrogen adsorption was achieved which resulted in a deeper and harder surface compared to conventional hardening methods. In this work, the effects of the laser power, pulse repetition frequency, and overlap percentage on laser surface treatment of 316 L SST steel samples with an argon-nitrogen jet will be presented. Resulting microstructure, phase type, microhardness, and wear resistance are presented.

  17. Surface modification of the metal plates using continuous electron beam process (CEBP)

    International Nuclear Information System (INIS)

    Kim, Jisoo; Kim, Jin-Seok; Kang, Eun-Goo; Park, Hyung Wook

    2014-01-01

    Highlights: • We performed surface modification of SM20C, SUS303, and Al6061 using CEBP. • We analyzed surface properties and microstructure after electron-beam irradiation. • The surface quality was improved after electron-beam irradiation. • The surface hardness for SM20C was increased by ∼50% after CEBP irradiation. - Abstract: The finishing process is an important component of the quality-control procedure for final products in manufacturing applications. In this study, we evaluated the performance of continuous electron-beam process as the final process for finishing SM20C (steel alloy), SUS303 (stainless steel alloy), and Al6061 (aluminum alloy) surfaces both on the initially smooth and rough surfaces. Surface modification of the metals was carried out by varying the feed and frequency of the continuous electron-beam irradiation procedure. The resulting surface roughness was examined with respect to the initial surface roughness of the metals. SM20C and SUS303 experienced an improvement in surface roughness, particularly for initially rough surfaces. Continuous electron-beam process produced craters during the process and the effect of this phenomenon on the resulting surface roughness was relatively large with the initially smooth SM20C and SUS303 alloy surfaces. For Al6061, the continuous electron-beam process was effective at improving its surface roughness even with the initially smooth surface under the optimized conditions of process; this was attributed to its low melting point. Scanning electron microscopy was used to identify metallurgical variation within the thin melted and re-solidification layers of the tested alloys. Changes in the surface contact angle and hardness before and after electron-beam irradiation were also examined

  18. Surface modification of the metal plates using continuous electron beam process (CEBP)

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jisoo, E-mail: kimjisu16@unist.ac.kr [School of Mechanical and Advanced Materials Engineering, Ulsan National Institute of Science and Technology, UNIST-gil 50, Eonyang-eup, Ulju-gun, Ulsan Metropolitan City 689-798 (Korea, Republic of); Kim, Jin-Seok, E-mail: totoro22@kitech.re.kr [Korea Institute of Industrial Technology (KITECH), KITECH Cheonan Headquarters 35-3 Hongcheon-ri, Ipjang-myeon, Cheonan-si, Chungcheongnam-do 330-825 (Korea, Republic of); Kang, Eun-Goo, E-mail: egkang@kitech.re.kr [Korea Institute of Industrial Technology (KITECH), KITECH Cheonan Headquarters 35-3 Hongcheon-ri, Ipjang-myeon, Cheonan-si, Chungcheongnam-do 330-825 (Korea, Republic of); Park, Hyung Wook, E-mail: hwpark@unist.ac.kr [School of Mechanical and Advanced Materials Engineering, Ulsan National Institute of Science and Technology, UNIST-gil 50, Eonyang-eup, Ulju-gun, Ulsan Metropolitan City 689-798 (Korea, Republic of)

    2014-08-30

    Highlights: • We performed surface modification of SM20C, SUS303, and Al6061 using CEBP. • We analyzed surface properties and microstructure after electron-beam irradiation. • The surface quality was improved after electron-beam irradiation. • The surface hardness for SM20C was increased by ∼50% after CEBP irradiation. - Abstract: The finishing process is an important component of the quality-control procedure for final products in manufacturing applications. In this study, we evaluated the performance of continuous electron-beam process as the final process for finishing SM20C (steel alloy), SUS303 (stainless steel alloy), and Al6061 (aluminum alloy) surfaces both on the initially smooth and rough surfaces. Surface modification of the metals was carried out by varying the feed and frequency of the continuous electron-beam irradiation procedure. The resulting surface roughness was examined with respect to the initial surface roughness of the metals. SM20C and SUS303 experienced an improvement in surface roughness, particularly for initially rough surfaces. Continuous electron-beam process produced craters during the process and the effect of this phenomenon on the resulting surface roughness was relatively large with the initially smooth SM20C and SUS303 alloy surfaces. For Al6061, the continuous electron-beam process was effective at improving its surface roughness even with the initially smooth surface under the optimized conditions of process; this was attributed to its low melting point. Scanning electron microscopy was used to identify metallurgical variation within the thin melted and re-solidification layers of the tested alloys. Changes in the surface contact angle and hardness before and after electron-beam irradiation were also examined.

  19. Effect of Surface Diffusion on Transfer Processes in Heterogeneous Systems

    Czech Academy of Sciences Publication Activity Database

    Levdansky, V.V.; Smolík, Jiří; Moravec, Pavel

    2008-01-01

    Roč. 51, 9-10 (2008), s. 2471-2481 ISSN 0017-9310 R&D Projects: GA ČR GA101/05/2214; GA ČR(CZ) GA101/05/2524; GA ČR GA104/07/1093 Institutional research plan: CEZ:AV0Z40720504 Keywords : adsorption * gas flow * surface diffusion Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 1.894, year: 2008

  20. Prospects of DLC coating as environment friendly surface treatment process.

    Science.gov (United States)

    Kim, S W; Kim, S G

    2011-06-01

    After first commercialization in 90's, the applications of diamond-like carbon (DLC) have been significantly expanded to tool, automobile parts, machineries and moulds to enhance wear and friction properties. Although DLC has many advantages like high hardness, low friction electrical insulating and chemical stability and has the possible market, its application in the field is still very limited due to the gaps of understanding between end-user and developer of its advantage of costing. Recently, one of the most popular issues in the surface modification is providing the long lasting super-hydrophilic or -hydrophobic properties on the material surface for the outdoor usage. A lot of material loss is caused due to water corrosion which has to do with the flow and contacts of water like fuel cell separator and air conditioner parts. The consequence of development of functional surface based on the hydrophilic or hydrophobic design for the important parts would be really helpful for materials to be cleaner and more energy effective. Here, we first reviewed the DLC technology and then examined the kind of surface modification as well as its merits and disadvantage. We also looked at how we can improve super-hydrophilic and super hydrophobic for the DLC coating layer as well as current status of technology and arts of DLC. In the end, we would like to suggest it as one of the environmental friendly industrial technology. Copyright © 2011 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

  1. Nanostructured surface processing by an intense pulsed ion beam irradiation

    International Nuclear Information System (INIS)

    Yatsuzuka, M.; Masuda, T.; Yamasaki, T.; Uchida, H.; Nobuhara, S.; Hashimoto, Y.; Yoshihara, Y.

    1997-01-01

    Metal surface modification by irradiating an intense pulsed ion beam (IPIB) with short pulse width has been studied experimentally. An IPIB irradiation to a target leads to rapid heating above its melting point. After the beam is turned off, the heated region is immediately cooled by thermal conduction at a cooling rate of typically 10 10 K/s. This rapid cooling and resolidification results in generation of nanostructured phase in the top of surface. The typical hydrogen IPIB parameters are 200 kV of energy, 500 A/cm 2 of current density and 70 ns of pulsewidth. The IPIB was irradiated on a pure titanium to generate nanocrystalline phase. The IPIB-irradiated surface was examined with X-ray diffraction, SEM, and HR-TEM. The randomly oriented lattice fringes as well as a halo diffraction pattern are observed in the HR-TEM micrograph of IPIB-irradiated titanium. The average grain size is found to be 32 nanometers

  2. Microbe-surface interactions in biofouling and biocorrosion processes.

    Science.gov (United States)

    Beech, Iwona B; Sunner, Jan A; Hiraoka, Kenzo

    2005-09-01

    The presence of microorganisms on material surfaces can have a profound effect on materials performance. Surface-associated microbial growth, i.e. a biofilm, is known to instigate biofouling. The presence of biofilms may promote interfacial physico-chemical reactions that are not favored under abiotic conditions. In the case of metallic materials, undesirable changes in material properties due to a biofilm (or a biofouling layer) are referred to as biocorrosion or microbially influenced corrosion (MIC). Biofouling and biocorrosion occur in aquatic and terrestrial habitats varying in nutrient content, temperature, pressure and pH. Interfacial chemistry in such systems reflects a wide variety of physiological activities carried out by diverse microbial populations thriving within biofilms. Biocorrosion can be viewed as a consequence of coupled biological and abiotic electron-transfer reactions, i.e. redox reactions of metals, enabled by microbial ecology. Microbially produced extracellular polymeric substances (EPS), which comprise different macromolecules, mediate initial cell adhesion to the material surface and constitute a biofilm matrix. Despite their unquestionable importance in biofilm development, the extent to which EPS contribute to biocorrosion is not well-understood. This review offers a current perspective on material/microbe interactions pertinent to biocorrosion and biofouling, with EPS as a focal point, while emphasizing the role atomic force spectroscopy and mass spectrometry techniques can play in elucidating such interactions.

  3. Free energy surfaces from nonequilibrium processes without work measurement

    Science.gov (United States)

    Adib, Artur B.

    2006-04-01

    Recent developments in statistical mechanics have allowed the estimation of equilibrium free energies from the statistics of work measurements during processes that drive the system out of equilibrium. Here a different class of processes is considered, wherein the system is prepared and released from a nonequilibrium state, and no external work is involved during its observation. For such "clamp-and-release" processes, a simple strategy for the estimation of equilibrium free energies is offered. The method is illustrated with numerical simulations and analyzed in the context of tethered single-molecule experiments.

  4. Facile preparation of self-healing superhydrophobic CeO2 surface by electrochemical processes

    Science.gov (United States)

    Nakayama, Katsutoshi; Hiraga, Takuya; Zhu, Chunyu; Tsuji, Etsushi; Aoki, Yoshitaka; Habazaki, Hiroki

    2017-11-01

    Herein we report simple electrochemical processes to fabricate a self-healing superhydrophobic CeO2 coating on Type 304 stainless steel. The CeO2 surface anodically deposited on flat stainless steel surface is hydrophilic, although high temperature-sintered and sputter-deposited CeO2 surface was reported to be hydrophobic. The anodically deposited hydrophilic CeO2 surface is transformed to hydrophobic during air exposure. Specific accumulation of contaminant hydrocarbon on the CeO2 surface is responsible for the transformation to hydrophobic state. The deposition of CeO2 on hierarchically rough stainless steel surface produces superhydrophobic CeO2 surface, which also shows self-healing ability; the surface changes to superhydrophilic after oxygen plasma treatment but superhydrophobic state is recovered repeatedly by air exposure. This work provides a facile method for preparing a self-healing superhydrophobic surface using practical electrochemical processes.

  5. Surface Distresses Detection of Pavement Based on Digital Image Processing

    OpenAIRE

    Ouyang , Aiguo; Luo , Chagen; Zhou , Chao

    2010-01-01

    International audience; Pavement crack is the main form of early diseases of pavement. The use of digital photography to record pavement images and subsequent crack detection and classification has undergone continuous improvements over the past decade. Digital image processing has been applied to detect the pavement crack for its advantages of large amount of information and automatic detection. The applications of digital image processing in pavement crack detection, distresses classificati...

  6. Improvement in Surface Characterisitcs of Polymers for Subsequent Electroless Plating Using Liquid Assisted Laser Processing

    DEFF Research Database (Denmark)

    Marla, Deepak; Zhang, Yang; Jabbaribehnam, Mirmasoud

    2016-01-01

    Metallization of polymers is a widely used process in the electronic industry that involves their surface modification as a pre-treatment step. Laser-based surface modification is one of the commonly used techniques for polymers due to its speed and precision. The process involves laser heating...... of the polymer surface to generate a rough or porous surface. Laser processing in liquid generates superior surface characteristics that result in better metal deposition. In this study, a comparison of the surface characteristics obtained by laser processing in water vis-à-vis air along with the deposition...... characteristics are presented. In addition, a numerical model based on the finite volume method is developed to predict the temperature profile during the process. Based on the model results, it is hypothesized that physical phenomena such as vapor bubble generation and plasma formation may occur in the presence...

  7. Stochastic Modeling and Deterministic Limit of Catalytic Surface Processes

    DEFF Research Database (Denmark)

    Starke, Jens; Reichert, Christian; Eiswirth, Markus

    2007-01-01

    Three levels of modeling, microscopic, mesoscopic and macroscopic are discussed for the CO oxidation on low-index platinum single crystal surfaces. The introduced models on the microscopic and mesoscopic level are stochastic while the model on the macroscopic level is deterministic. It can......, such that in contrast to the microscopic model the spatial resolution is reduced. The derivation of deterministic limit equations is in correspondence with the successful description of experiments under low-pressure conditions by deterministic reaction-diffusion equations while for intermediate pressures phenomena...

  8. Statistical and signal-processing concepts in surface metrology

    International Nuclear Information System (INIS)

    Church, E.L.; Takacs, P.Z.

    1986-03-01

    This paper proposes the use of a simple two-scale model of surface roughness for testing and specifying the topographic figure and finish of synchrotron-radiation mirrors. In this approach the effects of figure and finish are described in terms of their slope distribution and power spectrum, respectively, which are then combined with the system point spread function to produce a composite image. The result can be used to predict mirror performance or to translate design requirements into manufacturing specifications. Pacing problems in this approach are the development of a practical long-trace slope-profiling instrument and realistic statistical models for figure and finish errors

  9. Statistical and signal-processing concepts in surface metrology

    Energy Technology Data Exchange (ETDEWEB)

    Church, E.L.; Takacs, P.Z.

    1986-03-01

    This paper proposes the use of a simple two-scale model of surface roughness for testing and specifying the topographic figure and finish of synchrotron-radiation mirrors. In this approach the effects of figure and finish are described in terms of their slope distribution and power spectrum, respectively, which are then combined with the system point spread function to produce a composite image. The result can be used to predict mirror performance or to translate design requirements into manufacturing specifications. Pacing problems in this approach are the development of a practical long-trace slope-profiling instrument and realistic statistical models for figure and finish errors.

  10. Extracorporeal Treatment in Phenytoin Poisoning: Systematic Review and Recommendations from the EXTRIP (Extracorporeal Treatments in Poisoning) Workgroup.

    Science.gov (United States)

    Anseeuw, Kurt; Mowry, James B; Burdmann, Emmanuel A; Ghannoum, Marc; Hoffman, Robert S; Gosselin, Sophie; Lavergne, Valery; Nolin, Thomas D

    2016-02-01

    The Extracorporeal Treatments in Poisoning (EXTRIP) Workgroup conducted a systematic literature review using a standardized process to develop evidence-based recommendations on the use of extracorporeal treatment (ECTR) in patients with phenytoin poisoning. The authors reviewed all articles, extracted data, summarized findings, and proposed structured voting statements following a predetermined format. A 2-round modified Delphi method was used to reach a consensus on voting statements, and the RAND/UCLA Appropriateness Method was used to quantify disagreement. 51 articles met the inclusion criteria. Only case reports, case series, and pharmacokinetic studies were identified, yielding a very low quality of evidence. Clinical data from 31 patients and toxicokinetic grading from 46 patients were abstracted. The workgroup concluded that phenytoin is moderately dialyzable (level of evidence = C) despite its high protein binding and made the following recommendations. ECTR would be reasonable in select cases of severe phenytoin poisoning (neutral recommendation, 3D). ECTR is suggested if prolonged coma is present or expected (graded 2D) and it would be reasonable if prolonged incapacitating ataxia is present or expected (graded 3D). If ECTR is used, it should be discontinued when clinical improvement is apparent (graded 1D). The preferred ECTR modality in phenytoin poisoning is intermittent hemodialysis (graded 1D), but hemoperfusion is an acceptable alternative if hemodialysis is not available (graded 1D). In summary, phenytoin appears to be amenable to extracorporeal removal. However, because of the low incidence of irreversible tissue injury or death related to phenytoin poisoning and the relatively limited effect of ECTR on phenytoin removal, the workgroup proposed the use of ECTR only in very select patients with severe phenytoin poisoning. Copyright © 2016 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

  11. Gradient nanostructured surface of a Cu plate processed by incremental frictional sliding

    DEFF Research Database (Denmark)

    Hong, Chuanshi; Huang, Xiaoxu; Hansen, Niels

    2015-01-01

    The flat surface of a Cu plate was processed by incremental frictional sliding at liquid nitrogen temperature. The surface treatment results in a hardened gradient surface layer as thick as 1 mm in the Cu plate, which contains a nanostructured layer on the top with a boundary spacing of the order...

  12. Surface conductivity dependent dynamic behaviour of an ultrafine atmospheric pressure plasma jet for microscale surface processing

    Energy Technology Data Exchange (ETDEWEB)

    Abuzairi, Tomy [Graduate School of Science and Technology, Shizuoka University, Hamamatsu 432-8561 (Japan); Department of Electrical Engineering, Faculty of Engineering, Universitas Indonesia, Depok 16424 (Indonesia); Okada, Mitsuru [Department of Engineering, Shizuoka University, Hamamatsu 432-8561 (Japan); Bhattacharjee, Sudeep [Department of Physics, Indian Institute of Technology, Kanpur 208016 (India); Nagatsu, Masaaki, E-mail: nagatsu.masaaki@shizuoka.ac.jp [Graduate School of Science and Technology, Shizuoka University, Hamamatsu 432-8561 (Japan); Department of Engineering, Shizuoka University, Hamamatsu 432-8561 (Japan); Research Institute of Electronics, Shizuoka University, Hamamatsu 432-8561 (Japan)

    2016-12-30

    Highlights: • Spatio-temporal behaviors of capillary APPJs are studied for various substrates. • Plasma irradiation area depended on the substrate conductivity and permittivity. • Surface irradiation area was significantly broadened in polymer-like substrate. • Effect of applying a substrate bias on the APPJ irradiation area was investigated. - Abstract: An experimental study on the dynamic behaviour of microcapillary atmospheric pressure plasma jets (APPJs) with 5 μm tip size for surfaces of different conductivity is reported. Electrical and spatio-temporal characteristics of the APPJs are monitored using high voltage probe, current monitor and high speed intensified charge couple device camera. From these experimental results, we presented a simple model to understand the electrical discharge characteristics of the capillary APPJs with double electrodes, and estimated the velocity of the ionization fronts in the jet and the electron density to be 3.5–4.2 km/s and 2–7 × 10{sup 17} m{sup −3}. By analyzing the dynamics of the microcapillary APPJs for different substrate materials, it was found that the surface irradiation area strongly depended on the substrate conductivity and permittivity, especially in the case of polymer-like substrate, surface irradiation area was significantly broadened probably due to the repelling behaviour of the plasma jets from the accumulated electrical charges on the polymer surface. The effect of applying a substrate bias in the range from −900 V to +900 V on the plasma irradiation onto the substrates was also investigated. From the knowledge of the present results, it is helpful for choosing the substrate materials for microscale surface modification.

  13. Surface conductivity dependent dynamic behaviour of an ultrafine atmospheric pressure plasma jet for microscale surface processing

    International Nuclear Information System (INIS)

    Abuzairi, Tomy; Okada, Mitsuru; Bhattacharjee, Sudeep; Nagatsu, Masaaki

    2016-01-01

    Highlights: • Spatio-temporal behaviors of capillary APPJs are studied for various substrates. • Plasma irradiation area depended on the substrate conductivity and permittivity. • Surface irradiation area was significantly broadened in polymer-like substrate. • Effect of applying a substrate bias on the APPJ irradiation area was investigated. - Abstract: An experimental study on the dynamic behaviour of microcapillary atmospheric pressure plasma jets (APPJs) with 5 μm tip size for surfaces of different conductivity is reported. Electrical and spatio-temporal characteristics of the APPJs are monitored using high voltage probe, current monitor and high speed intensified charge couple device camera. From these experimental results, we presented a simple model to understand the electrical discharge characteristics of the capillary APPJs with double electrodes, and estimated the velocity of the ionization fronts in the jet and the electron density to be 3.5–4.2 km/s and 2–7 × 10"1"7 m"−"3. By analyzing the dynamics of the microcapillary APPJs for different substrate materials, it was found that the surface irradiation area strongly depended on the substrate conductivity and permittivity, especially in the case of polymer-like substrate, surface irradiation area was significantly broadened probably due to the repelling behaviour of the plasma jets from the accumulated electrical charges on the polymer surface. The effect of applying a substrate bias in the range from −900 V to +900 V on the plasma irradiation onto the substrates was also investigated. From the knowledge of the present results, it is helpful for choosing the substrate materials for microscale surface modification.

  14. Surface light scattering: integrated technology and signal processing

    DEFF Research Database (Denmark)

    Lading, L.; Dam-Hansen, C.; Rasmussen, E.

    1997-01-01

    systems representing increasing levels of integration are considered. It is demonstrated that efficient signal and data processing can be achieved by evaluation of the statistics of the derivative of the instantaneous phase of the detector signal. (C) 1997 Optical Society of America....

  15. Surface modification of hydroturbine steel using friction stir processing

    Science.gov (United States)

    Grewal, H. S.; Arora, H. S.; Singh, H.; Agrawal, A.

    2013-03-01

    Friction stir processing (FSP) has proved to be a viable tool for enhancing the mechanical properties of materials, however, the major focus has been upon improving the bulk properties of light metals and their alloys. Hydroturbines are susceptible to damage owing to slurry and cavitation erosion. In this study, FSP of a commonly employed hydroturbine steel, 13Cr4Ni was undertaken. Microstructural characterization of the processed steel was conducted using optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), X-ray diffraction (XRD) and electron back scatter diffraction (EBSD) techniques. Mechanical characterization of the steel was undertaken in terms of microhardness and resistance to cavitation erosion (CE). FSP resulted in the refinement of the microstructure with reduction in grain size by a factor of 10. EBSD results confirmed the existence of submicron and ultrafine grained microstructure. The microhardness of the steel was found to enhance by 2.6 times after processing. The processed steel also showed 2.4 times higher resistance against cavitation erosion in comparison to unprocessed steel. The primary erosion mechanism for both the steels was identical in nature, with plastic deformation responsible for the loss of material.

  16. Surface morphology evolution in silicon during ion beam processing; TOPICAL

    International Nuclear Information System (INIS)

    Bedrossian P; Caturla, M; Diaz de la Rubia, T; Johnson, M

    1999-01-01

    The Semiconductor Industry Association (SIA) projects that the semiconductor chips used in personal computers and scientific workstations will reach five times the speed and ten times the memory capacity of the current pentium-class processor by the year 2007. However, 1 GHz on-chip clock speeds and 64 Gbits/Chip DRAM technology will not come easy and without a price. Such technologies will require scaling the minimum feature size of CMOS devices (the transistors in the silicon chip) down to below 100nm from the current 180 to 250 nm. This requirement has profound implications for device manufacturing. Existing processing techniques must increasingly be understood quantitatively and modeled with unprecedented precision. Indeed, revolutionary advances in the development of physics-based process simulation tools will be required to achieve the goals for cost efficient manufacturing, and to satisfy the needs of the defense industrial base. These advances will necessitate a fundamental improvement in our basic understanding of microstructure evolution during processing. In order to cut development time and costs, the semiconductor industry makes extensive use of simple models of dopant implantation, and of phenomenological models of defect annealing and diffusion. However, the production of a single device often requires more than 200 processing steps, and the cumulative effects of the various steps are far too complex to be treated with these models. The lack of accurate process modeling simulators is proving to be a serious impediment to the development of next generation devices. New atomic-level models are required to describe the point defect distributions produced by the implantation process, and the defect and dopant diffusion resulting from rapid thermal annealing steps. In this LDRD project, we investigated the migration kinetics of defects and dopants in silicon both experimentally and theoretically to provide a fundamental database for use in the development

  17. Extracorporeal treatment for carbamazepine poisoning

    DEFF Research Database (Denmark)

    Ghannoum, Marc; Yates, Christopher; Galvao, Tais F

    2014-01-01

    in carbamazepine poisoning. METHODS: After a systematic literature search, the subgroup extracted the data and summarized the findings following a pre-determined format. The entire workgroup voted via a two-round modified Delphi method to reach a consensus on voting statements, using a RAND/UCLA Appropriateness......-vitro studies; two poor-quality observational studies were identified, yielding a very low quality of evidence for all recommendations. Data on 173 patients, including 6 fatalities, were reviewed. The workgroup concluded that carbamazepine is moderately dialyzable and made the following recommendations: ECTR...... is suggested in severe carbamazepine poisoning (2D). ECTR is recommended if multiple seizures occur and are refractory to treatment (1D), or if life-threatening dysrhythmias occur (1D). ECTR is suggested if prolonged coma or respiratory depression requiring mechanical ventilation are present (2D...

  18. Thermal Diffusion Processes in Metal-Tip-Surface Interactions: Contact Formation and Adatom Mobility

    DEFF Research Database (Denmark)

    Sørensen, Mads Reinholdt; Jacobsen, Karsten Wedel; Jonsson, Hannes

    1996-01-01

    and the surface can occur by a sequence of atomic hop and exchange processes which become active on a millisecond time scale when the tip is about 3-5 Angstrom from the surface. Adatoms on the surface are stabilized by the presence of the tip and energy barriers for diffusion processes in the region under the tip......We have carried out computer simulations to identify and characterize various thermally activated atomic scale processes that can play an important role in room temperature experiments where a metal tip is brought close to a metal surface. We find that contact formation between the tip...

  19. A high volume cost efficient production macrostructuring process. [for silicon solar cell surface treatment

    Science.gov (United States)

    Chitre, S. R.

    1978-01-01

    The paper presents an experimentally developed surface macro-structuring process suitable for high volume production of silicon solar cells. The process lends itself easily to automation for high throughput to meet low-cost solar array goals. The tetrahedron structure observed is 0.5 - 12 micron high. The surface has minimal pitting with virtually no or very few undeveloped areas across the surface. This process has been developed for (100) oriented as cut silicon. Chemi-etched, hydrophobic and lapped surfaces were successfully texturized. A cost analysis as per Samics is presented.

  20. Absorber management using burnable poisons

    International Nuclear Information System (INIS)

    Mortensen, L.

    1977-06-01

    An investigation of the problem of optimal control carried out by means of a two-dimensional model of a PWR reactor. A solution is found to the problem, and the possibility of achieving optimal control with burnable poisons such as boron, cadmium and gadolinium is discussed. Further, an attempt is made to solve the control problem of BWR, but no final solution is found. (author)

  1. Tribological investigations of the applicability of surface functionalization for dry extrusion processes

    Science.gov (United States)

    Teller, Marco; Prünte, Stephan; Ross, Ingo; Temmler, André; Schneider, Jochen M.; Hirt, Gerhard

    2017-10-01

    Cold extrusion processes are characterized by large relative contact stresses combined with a severe surface enlargement of the workpiece. Under these process conditions a high risk for galling of workpiece material to the tool steel occurs especially in processing of aluminum and aluminum alloys. In order to reduce adhesive wear lubricants for separation of workpiece and tool surfaces are used. As a consequence additional process steps (e.g. preparation and cleaning of workpieces) are necessary. Thus, the realization of a dry forming process is aspired from an environmental and economic perspective. In this paper a surface functionalization with self-assembled-monolayers (SAM) of the tool steels AISI D2 (DIN 1.2379) and AISI H11 (DIN 1.2343) is evaluated by a process-oriented tribological test. The tribological experiment is able to resemble and scale the process conditions of cold extrusion related to relative contact stress and surface enlargement for the forming of pure aluminum (Al99.5). The effect of reduced relative contact stress, surface enlargement and relative velocity on adhesive wear and tool lifetime is evaluated. Similar process conditions are achievable by different die designs with decreased extrusion ratios and adjusted die angles. The effect of surface functionalization critically depends on the substrate material. The different microstructure and the resulting differences in surface chemistry of the two tested tool steels appear to affect the performance of the tool surface functionalization with SAM.

  2. Surface Nano Structures Manufacture Using Batch Chemical Processing Methods for Tooling Applications

    DEFF Research Database (Denmark)

    Tosello, Guido; Calaon, Matteo; Gavillet, J.

    2011-01-01

    The patterning of large surface areas with nano structures by using chemical batch processes to avoid using highenergy intensive nano machining processes was investigated. The capability of different surface treatment methods of creating micro and nano structured adaptable mould inserts for subse...

  3. Processing and properties of electrodeposited layered surface coatings

    DEFF Research Database (Denmark)

    Horsewell, Andy

    1998-01-01

    Hard chromium, produced by conventional dir ect curl ent (DC) electrodeposition, cannot be deposited to thicknesses gl enter than about 5 mu m because of the buildup of processing stresses which cause channel cracks in the coating. Much thicker chromium coatings map be produced by depositing a la...... geometry is almost always analogous to bending, and fracture resistance is provided through deviation of the channel crack by weak interfaces, resulting in 'terrace cracking'....

  4. Recycling and surface erosion processes in contemporary tokamaks

    International Nuclear Information System (INIS)

    McCracken, G.M.

    1979-03-01

    A number of global models have recently had considerable success in describing recycling. These are briefly reviewed. It is shown that large gas concentrations can build up in the walls and that these concentrations are seriously affected by erosion and deposition processes and by deliberate gettering with titanium. Finally, the measurement of the concentration of hydrogen in probes is discussed as a means of measuring plasma edge characteristics

  5. Poison hemlock (Conium maculatum L.).

    Science.gov (United States)

    Vetter, J

    2004-09-01

    One of the most poisonous species amongst higher plants is Conium maculatum. It is a very common nitrophile weed species, belonging to the Apiaceae (formerly Umbelliferae) family. It contains some piperidine alkaloids (coniine, N-methyl-coniine, conhydrine, pseudoconhydrine, gamma-coniceine), which are formed by the cyclisation of an eight-carbon chain derived from four acetate units. gamma-Coniceine is the precursor of the other hemlock alkaloids. All vegetative organs, flowers and fruits contain alkaloids. The concentrations (both absolute and relative) of the different alkaloids depend on plant varieties, on ecological conditions and on the age of the plant. The characteristic biological effects of the plants are summarised on cattle, sheep, goat, swine, rabbit, elk, birds and insects and the symptoms of the human toxicosis (some cases of poisonings) are discussed according to the literature data. The general symptoms of hemlock poisoning are effects on nervous system (stimulation followed by paralysis of motor nerve endings and CNS stimulation and later depression), vomiting, trembling, problems in movement, slow and weak later rapid pulse, rapid respiration, salivation, urination, nausea, convulsions, coma and death.

  6. Influence of the surface layer characteristics on the regularities of the cutting process

    Directory of Open Access Journals (Sweden)

    Krainev Dmitriy V.

    2017-01-01

    Full Text Available The article considers the influence of the surface layer characteristics on the regularities of the cutting process and the formation of the quality of the surface machined. This effect has been confirmed by the study results of the combined cutting method with advanced plastic deformation (APD. The work estimates the impact of the change in the surface layer properties on the forces and temperature of cutting, stability of the chip formation and quality parameters of the surface machined.

  7. Effect of different machining processes on the tool surface integrity and fatigue life

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Chuan Liang [College of Mechanical and Electrical Engineering, Nanchang University, Nanchang (China); Zhang, Xianglin [School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan (China)

    2016-08-15

    Ultra-precision grinding, wire-cut electro discharge machining and lapping are often used to machine the tools in fine blanking industry. And the surface integrity from these machining processes causes great concerns in the research field. To study the effect of processing surface integrity on the fine blanking tool life, the surface integrity of different tool materials under different processing conditions and its influence on fatigue life were thoroughly analyzed in the present study. The result shows that the surface integrity of different materials was quite different on the same processing condition. For the same tool material, the surface integrity on varying processing conditions was quite different too and deeply influenced the fatigue life.

  8. Microscopic investigation of RF surfaces of 3 GHz niobium accelerator cavities following RF processing

    International Nuclear Information System (INIS)

    Graber, J.; Barnes, P.; Flynn, T.; Kirchgessner, J.; Knobloch, J.; Moffat, D.; Muller, H.; Padamsee, H.; Sears, J.

    1993-01-01

    RF processing of Superconducting accelerating cavities is achieved through a change in the electron field emission (FE) characteristics of the RF surface. The authors have examined the RF surfaces of several single-cell 3 GHz cavities, following RF processing, in a Scanning Electron Microscope (SEM). The RF processing sessions included both High Peak Power (P ≤ 50 kW) pulsed processing, and low power (≤ 20 W) continuous wave processing. The experimental apparatus also included a thermometer array on the cavity outer wall, allowing temperature maps to characterize the emission before and after RF processing gains. Multiple sites have been located in cavities which showed improvements in cavity behavior due to RF processing. Several SEM-located sites can be correlated with changes in thermometer signals, indicating a direct relationship between the surface site and emission reduction due to RF processing. Information gained from the SEM investigations and thermometry are used to enhance the theoretical model of RF processing

  9. Poisoning of bubble propelled catalytic micromotors: the chemical environment matters.

    Science.gov (United States)

    Zhao, Guanjia; Sanchez, Samuel; Schmidt, Oliver G; Pumera, Martin

    2013-04-07

    Self-propelled catalytic microjets have attracted considerable attention in recent years and these devices have exhibited the ability to move in complex media. The mechanism of propulsion is via the Pt catalysed decomposition of H2O2 and it is understood that the Pt surface is highly susceptible to poisoning by sulphur-containing molecules. Here, we show that important extracellular thiols as well as basic organic molecules can significantly hamper the motion of catalytic microjet engines. This is due to two different mechanisms: (i) molecules such as dimethyl sulfoxide can quench the hydroxyl radicals produced at Pt surfaces and reduce the amount of oxygen gas generated and (ii) molecules containing -SH, -SSR, and -SCH3 moieties can poison the catalytically active platinum surface, inhibiting the motion of the jet engines. It is essential that the presence of such molecules in the environment be taken into consideration for future design and operation of catalytic microjet engines. We show this effect on catalytic micromotors prepared by both rolled-up and electrodeposition approaches, demonstrating that such poisoning is universal for Pt catalyzed micromotors. We believe that our findings will contribute significantly to this field to develop alternative systems or catalysts for self-propulsion when practical applications in the real environment are considered.

  10. Development of sustainable paper coatings using nanoscale industrial surface processing

    DEFF Research Database (Denmark)

    Markert, Frank; Breedveld, Leo; Lahti, Johanna

    in the PlasmaNice project, as environmental and social aspects are addressed using methods like life cycle check (LCC), life cycle assessment (LCA), and industrial risk assessment (RA) within the boundary of an economical production for different market segments. The results are intended to be used partly...... products, and the process and material developers providing new coatings with specific properties. The combination of RA and LCA/LCC within the early stages of product development provide a more holistic approach, It is commonly believed to be also economical beneficial as changes are easier to implement...

  11. Hemlock (Conium Maculatum) Poisoning In A Child

    OpenAIRE

    KONCA, Capan; KAHRAMANER, Zelal; BOSNAK, Mehmet; KOCAMAZ, Halil

    2016-01-01

    SUMMARY Poison hemlock (Conium maculatum) is a plant that is poisonous for humans and animals. Accidental ingestion of the plant may result in central nervous system depression, respiratory failure, acute rhabdomyolysis, acute renal failure and even death. The main treatment of hemlock poisoning is supportive care. The case of a 6-year-old girl who was admitted to the emergency department with complaints of burning sensation in mouth, hypersalivation, tremor in hands and ataxia after ingestio...

  12. Personality traits in persons with manganese poisoning

    Energy Technology Data Exchange (ETDEWEB)

    Platonov, A A

    1976-10-01

    Results of studies with the Minnesota Multiphasic Personality Inventory (MMPI) in 3 groups of arc welders with various degrees of manganese poisoning (22 symptom-free, 23 with functional disturbances, 55 with organic symptoms) and 50 controls were discussed. There was a close relation between the severity of the poisoning and quantitative and qualitative personality changes. Personality tests are considered a useful addition to the clinical diagnosis of chronic manganese poisoning.

  13. Air/surface exchange processes of mercury and their linkage to atmospheric pools

    International Nuclear Information System (INIS)

    Bahlmann, Enno; Ebinghaus, Ralf

    2001-01-01

    The atmospheric mercury cycle is strongly linked to the terrestrial, aquatic and biologic cycle of mercury via air/surface exchange processes. In order to quantify mercury fluxes from and to the atmosphere to predict local and regional source contributions the methods for flux measurements as well as the physicochemical factors controlling air/surface exchange processes must be assessed. We will describe methods for the determination of mercury and mercury species in ambient air which are basic for investigation of air/surface exchange processes. Further on we will describe approaches for studying the physicochemical factors controlling this processes by using a new laboratory flux measurement system. (author)

  14. Improvement of Surface Properties of CP-Titanium by Thermo-Chemical Treatment (TCT) Process

    International Nuclear Information System (INIS)

    Jeong, Hyeon-Gyeong; Hur, Bo-Young; Lee, Dong-Geun; Lee, Yong-Tai; Yaskiv, O.

    2011-01-01

    The thermo-chemical treatment (TCT) process was applied to achieve surface hardening of CP titanium. The following three different surface modification conditions were tested so that the best surface hardening process could be selected:(a) PVD, (b) TCT+PVD, and (c) TCT+Aging+PVD. These specimens were tested and analyzed in terms of surface roughness, wear, friction coefficient, and the gradient of hardening from the surface of the matrix. The three test conditions were all beneficial to improve the surface hardness of CP titanium. Moreover, the TCT treated specimens, that is, (b) and (c), showed significantly improved surface hardness and low friction coefficients through the thickness up to 100um. This is due to the functionally gradient hardened surface improvement by the diffused interstitial elements. The hardened surface also showed improvement in bonding between the PVD and TCT surface, and this leads to improvement in wear resistance. However, TCT after aging treatment did not show much improvement in surface properties compared to TCT only. For the best surface hardening on CP titanium, TCT+PVD has advantages in surface durability and economics.

  15. Analysis of intentional drug poisonings using Ohio Poison Control Center Data, 2002-2014.

    Science.gov (United States)

    Pringle, Kelsey; Caupp, Sarah; Shi, Junxin; Wheeler, Krista K; Spiller, Henry A; Casavant, Marcel J; Xiang, Henry

    2017-08-01

    Pharmaceutical drug poisonings, especially those that are intentional, are a serious problem for adolescents and young adults. Poison control center data is a viable tool to track intentional drug poisonings in near real-time. To determine intentional drug poisoning rates among adolescents and young adults in Ohio using poison control center data. We analyzed data from 2002 to 2014 obtained by Ohio's three poison control centers. Inclusion variables were calls made to the centers that had appropriate subject age (10-29 years old), subject sex, involved substance (all drug classes), and medical outcome (no effect, minor effect, moderate effect, major effect, and death). Intentional drug poisoning reports were also separated into subgroups to compare suspected suicide reports to misuse and abuse reports. Finally, resident population estimates were used to generate 2014 intentional drug poisoning rates for each county in Ohio. The most common age group for intentional drug poisonings was 18-24. Females reported more suspected suicide drug poisonings while males reported more misuse/abuse drug poisonings. The most reported drug class across all ages was analgesics. Of the 88 counties in Ohio, Hamilton, Williams, Washington, and Guernsey counties had the highest rates of intentional drug poisonings. The high report rate of suspected suicides and analgesic class drugs demonstrates the need for preventative measures for adolescents and young adults in Ohio. Any interventions, along with legislative changes, will need to take place in our local communities.

  16. Hemlock (Conium Maculatum) Poisoning In A Child.

    Science.gov (United States)

    Konca, Capan; Kahramaner, Zelal; Bosnak, Mehmet; Kocamaz, Halil

    2014-03-01

    Poison hemlock (Conium maculatum) is a plant that is poisonous for humans and animals. Accidental ingestion of the plant may result in central nervous system depression, respiratory failure, acute rhabdomyolysis, acute renal failure and even death. The main treatment of hemlock poisoning is supportive care. The case of a 6-year-old girl who was admitted to the emergency department with complaints of burning sensation in mouth, hypersalivation, tremor in hands and ataxia after ingestion of poison hemlock is presented here with clinical and laboratory features. In this case, we aim to report that accidental ingestion of plants resembling vegetables that are consumed daily can lead to serious complications and even death.

  17. Potato plant poisoning - green tubers and sprouts

    Science.gov (United States)

    ... large ingestions. These poisonings can be very dangerous. Symptoms may include: Vomiting Stomach or abdominal pain Diarrhea Fever Delirium Dilated pupils Hallucinations Headache Loss of sensation Lower ...

  18. Carbon activation process for increased surface accessibility in electrochemical capacitors

    Science.gov (United States)

    Doughty, Daniel H.; Eisenmann, Erhard T.

    2001-01-01

    A process for making carbon film or powder suitable for double capacitor electrodes having a capacitance of up to about 300 F/cm.sup.3 is disclosed. This is accomplished by treating in aqueous nitric acid for a period of about 5 to 15 minutes thin carbon films obtained by carbonizing carbon-containing polymeric material having a high degree of molecular directionality, such as polyimide film, then heating the treated carbon film in a non-oxidizing atmosphere at a non-graphitizing temperature of at least 350.degree. C. for about 20 minutes, and repeating alternately the nitric acid step and the heating step from 7 to 10 times. Capacitors made with this carbon may find uses ranging from electronic devices to electric vehicle applications.

  19. Study of the processes of adsorption of amine-containing surface-active substance on the surface of Aluminum powder

    Directory of Open Access Journals (Sweden)

    Antonina Dyuryagina

    2012-03-01

    Full Text Available Equilibrium characteristics of adsorption on a surface of a pigment depending on concentration factors and temperature of the dispersive environment are defined. Kinetic laws of superficial activity of binary, threefold homogeneous and heterogeneous modeling systems are studied. The estimation of mechanisms of process of adsorption is carried out.

  20. Educational Case: Lead Poisoning

    Directory of Open Access Journals (Sweden)

    Barbara E. C. Knollmann-Ritschel MD

    2017-08-01

    Full Text Available The following fictional case is intended as a learning tool within the Pathology Competencies for Medical Education (PCME, a set of national standards for teaching pathology. These are divided into three basic competencies: Disease Mechanisms and Processes, Organ System Pathology, and Diagnostic Medicine and Therapeutic Pathology. For additional information, and a full list of learning objectives for all three competencies, see http://journals.sagepub.com/doi/10.1177/2374289517715040 .

  1. The process development of laser surface modification of commercially pure titanium (Grade 2) with rhenium

    Science.gov (United States)

    Kobiela, K.; Smolina, I.; Dziedzic, R.; Szymczyk, P.; Kurzynowski, T.; Chlebus, E.

    2016-12-01

    The paper presents the results of the process development of laser surface modification of commercially pure titanium with rhenium. The criterion of the successful/optimal process is the repetitive geometry of the surface, characterized by predictable and repetitive chemical composition over its entire surface as well as special mechanical properties (hardness and wear resistance). The analysis of surface geometry concluded measurements of laser penetration depth and heat affected zone (HAZ), the width of a single track as well as width of a clad. The diode laser installed on the industrial robot carried out the laser treatment. This solution made possible the continuous supply of powder to the substrate during the process. The aim of an investigation is find out the possibility of improving the tribological characteristics of the surface due to the rhenium alloying. The verification of the surface properties (tribological) concluded geometry measurements, microstructure observation, hardness tests and evaluation of wear resistance.

  2. A post-processing study on aluminum surface by fiber laser: Removing face milling patterns

    Science.gov (United States)

    Kayahan, Ersin

    2018-05-01

    The face milling process of the metal surface is a well-known machining process of using rotary cutters to remove material from a workpiece. Flat metal surfaces can be produced by a face milling process. However, in practice, visible, traced marks following the motion of points on the cutter's face are usually apparent. In this study, it was shown that milled patterns can be removed by means of 20 W fiber laser on the aluminum surface (AA7075). Experimental results also showed that roughened and hydrophobic surface can be produced with optimized laser parameters. It is a new approach to remove the patterns from the metal surface and can be explained through roughening by re-melting instead of ablation. The new method is a strong candidate to replace sandblasting the metal surface. It is also cheap and environmentally friendly.

  3. The theory of development of surface morphology by sputter erosion processes

    International Nuclear Information System (INIS)

    Carter, G.; Nobes, M.J.

    1984-01-01

    When a surface is bombarded by an energetic ion flux a rich variety of surface structures are observed to develop at the atomic, microscopic and macroscopic scales. Such structures include elevated, with respect to the surrounding surface, features such as mesas or plateaux, ridges, cones and pyramids and depressed features such as etch pits and cavities. These elementary features may be isolated or in profusion and frequently repetitive patterns of coordinated pyramidal structures, etch pits, surface ledges or facets and ripple or wave-like structures occur. The majority of the features arise rather directly from the erosion action of the sputtering process, particularly from differential erosion processes at different surface localities. The authors outline a general approach to sputter erosion induced surface morphology development based on the concept of the surface as an advancing wave. (Auth.)

  4. Ciguatera Fish Poisoning and Climate Change: Analysis of National Poison Center Data in the United States, 2001–2011

    Science.gov (United States)

    Strickland, Matthew J.; Hess, Jeremy J.

    2014-01-01

    Background: Warm sea surface temperatures (SSTs) are positively related to incidence of ciguatera fish poisoning (CFP). Increased severe storm frequency may create more habitat for ciguatoxic organisms. Although climate change could expand the endemic range of CFP, the relationship between CFP incidence and specific environmental conditions is unknown. Objectives: We estimated associations between monthly CFP incidence in the contiguous United States and SST and storm frequency in the Caribbean basin. Methods: We obtained information on 1,102 CFP-related calls to U.S. poison control centers during 2001–2011 from the National Poison Data System. We performed a time-series analysis using Poisson regression to relate monthly CFP call incidence to SST and tropical storms. We investigated associations across a range of plausible lag structures. Results: Results showed associations between monthly CFP calls and both warmer SSTs and increased tropical storm frequency. The SST variable with the strongest association linked current monthly CFP calls to the peak August SST of the previous year. The lag period with the strongest association for storms was 18 months. If climate change increases SST in the Caribbean 2.5–3.5°C over the coming century as projected, this model implies that CFP incidence in the United States is likely to increase 200–400%. Conclusions: Using CFP calls as a marker of CFP incidence, these results clarify associations between climate variability and CFP incidence and suggest that, all other things equal, climate change could increase the burden of CFP. These findings have implications for disease prediction, surveillance, and public health preparedness for climate change. Citation: Gingold DB, Strickland MJ, Hess JJ. 2014. Ciguatera fish poisoning and climate change: analysis of National Poison Center data in the United States, 2001–2011. Environ Health Perspect 122:580–586; http://dx.doi.org/10.1289/ehp.1307196 PMID:24618280

  5. Surface modification by electrolytic plasma processing for high Nb-TiAl alloys

    Science.gov (United States)

    Gui, Wanyuan; Hao, Guojian; Liang, Yongfeng; Li, Feng; Liu, Xiao; Lin, Junpin

    2016-12-01

    Metal surface modification by electrolytic plasma processing (EPP) is an innovative treatment widely commonly applied to material processing and pretreatment process of coating and galvanization. EPP involves complex processes and a great deal of parameters, such as preset voltage, current, solution temperature and processing time. Several characterization methods are presented in this paper for evaluating the micro-structure surfaces of Ti45Al8Nb alloys: SEM, EDS, XRD and 3D topography. The results showed that the oxide scale and other contaminants on the surface of Ti45Al8Nb alloys can be effectively removed via EPP. The typical micro-crater structure of the surface of Ti45Al8Nb alloys were observed by 3D topography after EPP to find that the mean diameter of the surface structure and roughness value can be effectively controlled by altering the processing parameters. The mechanical properties of the surface according to nanomechanical probe testing exhibited slight decrease in microhardness and elastic modulus after EPP, but a dramatic increase in surface roughness, which is beneficial for further processing or coating.

  6. Fabricating Super-hydrophobic Polydimethylsiloxane Surfaces by a Simple Filler-Dissolved Process

    Science.gov (United States)

    Lin, Yung-Tsan; Chou, Jung-Hua

    2010-12-01

    The self-cleaning effect of super-hydrophobic surfaces has attracted the attention of researchers. Typical ways of manufacturing super-hydrophobic surfaces include the use of either dedicated equipment or a complex chemical process. In this study, a simple innovative filler-dissolved method is developed using mainly powder salt and rinsing to form hydrophobic surfaces. This method can produce large super-hydrophobic surfaces with porous and micro rib surface structures. It can also be applied to curved surfaces, including flexible membranes. The contact angle of the manufactured artificial hydrophobic surface is about 160°. Furthermore, water droplets roll off the surface readily at a sliding angle of less than 5°, resembling the nonwetting lotus like effect.

  7. Characteristics of poisoning cases in Adiyaman city

    Directory of Open Access Journals (Sweden)

    Öznur Uludağ

    2015-09-01

    Full Text Available Objective: Aim of this study was to retrospectively evaluate poisoning cases in an intensive care unit (ICU in order to determine the profile of poisoning cases, update epidemiological data in Adiyaman, and contribute to data about poisoning in our country. Methods: Between 01-01-2012 and 31-12-2013 174 patients (116 males, 58 females with a mean age of 23.7 years were treated. Demographic characteristics, reasons and ways of poisoning, types of toxic substances, length of their ICU stay and prognosis were evaluated. Results: 2733 patients admitted to the intensive care unit were 174 poisoning cases. Poisoning ways were suicide by drug overdose (n=162, 93.1%, and accidental poisoning (n=12,6.9%.119 patients (66.5% had single drug intake, thirty-three patients (18.4% with multiple drug intake, and 16 (8.9% were poisoned by organic phosphates. The most common drug used for suicide was antidepressants (n=87.5%. 32 patients (18.4% took analgesics and anti-inflammatory drugs. A total of 152 patients taking the drug, 22 patients were poisoned by other means. The median length of patient stay was 2 days (range 1-20 days. Ninety-nine patients (56.9% recovered and were discharged.72 patients (41.4% were admitted to inpatient after intensive care unit. Patients were followed up by asking poisoning suicidal psychiatric consultation.1 patient was followed up for 20 days in intensive care due to alcohol poisoning but was died.2 patients (1.1% were referred to a center forward. Conclusion: Majority of the patients were females, who took drugs with suicidal intention. Frequent use of antidepressants, which are not subject to control by authorities, to commit suicide was remarkable.

  8. Food-safe modification of stainless steel food processing surfaces to reduce bacterial biofilms.

    Science.gov (United States)

    Awad, Tarek Samir; Asker, Dalal; Hatton, Benjamin D

    2018-06-11

    Biofilm formation on stainless steel (SS) surfaces of food processing plants, leading to foodborne illness outbreaks, is enabled by the attachment and confinement within microscale cavities of surface roughness (grooves, scratches). We report Foodsafe Oil-based Slippery Coatings (FOSCs) for food processing surfaces that suppress bacterial adherence and biofilm formation by trapping residual oil lubricant within these surface cavities to block microbial growth. SS surfaces were chemically functionalized with alkylphosphonic acid to preferentially wet a layer of food grade oil. FOSCs reduced the effective surface roughness, the adhesion of organic food residue, and bacteria. FOSCs significantly reduced Pseudomonas aeruginosa biofilm formation on standard roughness SS-316 by 5 log CFU cm-2, and by 3 log CFU cm-2 for mirror-finished SS. FOSCs also enhanced surface cleanability, which we measured by bacterial counts after conventional detergent cleaning. Importantly, both SS grades maintained their anti-biofilm activity after erosion of the oil layer by surface wear with glass beads, which suggests there is a residual volume of oil that remains to block surface cavity defects. These results indicate the potential of such low-cost, scalable approaches to enhance the cleanability of SS food processing surfaces and improve food safety by reducing biofilm growth.

  9. Extracorporeal treatment for barbiturate poisoning: recommendations from the EXTRIP Workgroup.

    Science.gov (United States)

    Mactier, Robert; Laliberté, Martin; Mardini, Joelle; Ghannoum, Marc; Lavergne, Valery; Gosselin, Sophie; Hoffman, Robert S; Nolin, Thomas D

    2014-09-01

    The EXTRIP (Extracorporeal Treatments in Poisoning) Workgroup conducted a systematic review of barbiturate poisoning using a standardized evidence-based process to provide recommendations on the use of extracorporeal treatment (ECTR) in patients with barbiturate poisoning. The authors reviewed all articles, extracted data, summarized key findings, and proposed structured voting statements following a predetermined format. A 2-round modified Delphi method was used to reach a consensus on voting statements, and the RAND/UCLA Appropriateness Method was used to quantify disagreement. 617 articles met the search inclusion criteria. Data for 538 patients were abstracted and evaluated. Only case reports, case series, and nonrandomized observational studies were identified, yielding a low quality of evidence for all recommendations. Using established criteria, the workgroup deemed that long-acting barbiturates are dialyzable and short-acting barbiturates are moderately dialyzable. Four key recommendations were made. (1) The use of ECTR should be restricted to cases of severe long-acting barbiturate poisoning. (2) The indications for ECTR in this setting are the presence of prolonged coma, respiratory depression necessitating mechanical ventilation, shock, persistent toxicity, or increasing or persistently elevated serum barbiturate concentrations despite treatment with multiple-dose activated charcoal. (3) Intermittent hemodialysis is the preferred mode of ECTR, and multiple-dose activated charcoal treatment should be continued during ECTR. (4) Cessation of ECTR is indicated when clinical improvement is apparent. This report provides detailed descriptions of the rationale for all recommendations. In summary, patients with long-acting barbiturate poisoning should be treated with ECTR provided at least one of the specific criteria in the first recommendation is present. Copyright © 2014 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

  10. Burnable poison rod for a nuclear reactor fuel assembly

    International Nuclear Information System (INIS)

    Funk, C.E.; Oneufer, A.S.

    1984-01-01

    A burnable poison rod for use in a nuclear reactor fuel assembly which includes concentrically disposed rods having an annular space therebetween which extends the full length of the rods. The inner rod is hollow to permit circulation of coolant therethrough. Annular burnable poison pellets are positioned in the annular space which is closed at both ends by plugs. A spring clip is located in the plenum space above the pellet stack in the rods. The spring clip is of cylindrical configuration having a gap in the material which provides two ends adapted to be squeezed toward each other. A cross section of the clip shows that its ends contain alternating flat and round edges, the round edges conforming to the outer rod inner surface to provide a retentive force which is releasably applied to the pellet stack as it grows during operation in a reactor

  11. Extracorporeal treatment for digoxin poisoning

    DEFF Research Database (Denmark)

    Mowry, James B; Burdmann, Emmanuel A; Anseeuw, Kurt

    2016-01-01

    patients, including six fatalities, it was concluded that digoxin is slightly dialyzable (level of evidence = B), and that ECTR is unlikely to improve the outcome of digoxin-toxic patients whether or not digoxin immune Fab (Fab) is administered. Despite the lack of robust clinical evidence, the workgroup...... recommended against the use of ECTR in cases of severe digoxin poisoning when Fab was available (1D) and also suggested against the use of ECTR when Fab was unavailable (2D). CONCLUSION: ECTR, in any form, is not indicated for either suspected or proven digoxin toxicity, regardless of the clinical context......, and is not indicated for removal of digoxin-Fab complex....

  12. Characterization of surface processes on mineral surfaces in aqueous solutions. Annual report for fiscal year 1993

    International Nuclear Information System (INIS)

    Leckie, J.O.

    1993-11-01

    Performance assessments by Los Alamos National Laboratory for the DOE's Yucca Mountain Site Characterization Project (YMP) are being done investigating the environmental risk related to long-term disposal of hazardous wastes resulting from the use of radioactive materials that must subsequently be isolated from the environment. The YMP site, located in southwestern Nevada, is intended for the storage of high-level wastes generated by nuclear energy-related activities, including spent fuel and waste from reprocessed fuel rods. The work covered by this contract is necessary for producing a defensible model and dataset, and may be critical for evaluation of repository compliance. This work, performed by the Environmental Engineering and Science research group at Stanford University, will quantify the adsorption of uranyl on various minerals. The project's principle objective is to provide sorption coefficients for uranyl and other ions of interest to predict radionuclide movements form the repository to accessible environments. This adsorption data is essential for the unambiguous interpretation of field experiments and observations. In this report, details of the activity and progress made with respect to the study of uranyl adsorption on mineral surfaces is presented and discussed

  13. Diagnosis & Treatment of Poisoning by Pesticides.

    Science.gov (United States)

    Environmental Protection Agency, Washington, DC. Office of Pesticide Programs.

    This report succinctly discusses the steps necessary to diagnose and treat poisoning from pesticides, especially organophosphates, carbamates and chlorinated hydrocarbons. Immediate and continuing steps in the care of poisoning victims are outlined with supportive information on where to locate emergency assistance. (CS)

  14. Beryllium poisonings; Les intoxications par le beryllium

    Energy Technology Data Exchange (ETDEWEB)

    Alibert, S.

    1959-03-15

    This note reports a bibliographical study of beryllium toxicity. Thus, this bibliographical review addresses and outlines aspects and issues like aetiology, cases of acute poisoning (cutaneous manifestations, pulmonary manifestations), chronic poisoning (cutaneous, pulmonary and bone manifestations), excretion and localisation, and prognosis.

  15. Argument Strategies: Antidote to Tylenol's Poisoned Image.

    Science.gov (United States)

    Benoit, William L.; Lindsey, James J.

    1987-01-01

    Analyzes how the manufacturer dealt with the Tylenol poisonings: the link between Tylenol and the poisoning was denied, its image as a safe product was bolstered, capsules were differentiated from other products, and as a result, sales recovered. Extends the applicability of apologia as a way to analyze other media campaigns. (SKC)

  16. A retrospective analysis of acute organophosphorus poisoning ...

    African Journals Online (AJOL)

    organophosphorus (OP) poisoning cases in a tertiary care hospital. Materials and ... In a pre-structured proforma, data regarding age, sex, time elapsed after intake, circumstances of poisoning, duration of hospitalization ... responsible for majority of self-attempted deaths ... cleansed with water at the time of admission.

  17. Cardiological aspects of carbon monoxide poisoning.

    Science.gov (United States)

    Marchewka, Jakub; Gawlik, Iwona; Dębski, Grzegorz; Popiołek, Lech; Marchewka, Wojciech; Hydzik, Piotr

    2017-01-01

    The aim of this study was to assess cardiological manifestations of carbon monoxide (CO) poisoning. Background/introduction: Carbon monoxide intoxication is one of the most important toxicological causes of morbidity and mortality worldwide. Early clinical manifestation of CO poisoning is cardiotoxicity. We enrolled 75 patients (34 males and 41 females, mean age 37.6 ± 17.7 y/o) hospitalized due to CO poisoning. Laboratory tests including troponin I, blood pressure measurements, HR and electrocardiograms (ECG) were collected. Pach's scale scoring and grading system was used to establish severity of poisoning. Grade of poisoning is positively correlated with troponin I levels and systolic blood pressure. Moreover, troponin levels are significantly correlated with exposition time, lactates and are higher in tachycardiac, hypertensive and positive ECG subpopulations. COHb levels are indicative of exposure but do not correlate with grade of poisoning. The main cause of CO poisoning were bathroom heaters - 83%, only 11% of examined intoxicated population were equipped with CO detectors. Complex cardiological screening covering troponin levels, ECG, blood pressure and heart rate measurements as well as complete blood count with particular attention to platelet parameters should be performed in each case where CO intoxication is suspected. More emphasis on education on CO poisoning is needed.

  18. Tropane alkaloids in food: poisoning incidents

    NARCIS (Netherlands)

    Adamse, P.; Egmond, van H.P.; Noordam, M.Y.; Mulder, P.P.J.; Nijs, de W.C.M.

    2014-01-01

    A large number of wild and cultured plants produce secondary metabolites that can be toxic to humans and animals. The present study aims to provide insight into the routes of (un)intentional poisonings of humans by tropane alkaloids. Poisonings of humans by tropane alkaloids occur as unintended

  19. 76 FR 9585 - Poison Control Program

    Science.gov (United States)

    2011-02-18

    ... delay or gap in poison center services. The State of New York has determined that the Research... Noncompetitive Replacement Awards to the Research Foundation of SUNY and the New York City Health & Hospitals... the Research Foundation of SUNY d.b.a. the Upstate New York Poison Control Center. HRSA will also...

  20. Poisonings in the Nordic countries in 2007

    DEFF Research Database (Denmark)

    Andrew, Erik; Tellerup, Markus; Termälä, Anna-Mariia

    2012-01-01

    To map mortality and morbidity of poisonings in Denmark, Finland, Iceland, Norway and Sweden in 2007 and undertake a comparison with a corresponding study in 2002.......To map mortality and morbidity of poisonings in Denmark, Finland, Iceland, Norway and Sweden in 2007 and undertake a comparison with a corresponding study in 2002....

  1. Accidental Poisoning with Otapiapia: a Local Organophasphate ...

    African Journals Online (AJOL)

    Children are prone to accidental poisoning. We report this fatal organophosphate poisoning of a 3-year-old Nigerian boy following accidental ingestion of a homemade cocktail of kerosene and 'Otapiapia': a local rodenticide to highlight the dangers inherent in un-regulated production, home use and storage of this ...

  2. Validation of a Poison Prevention Program.

    Science.gov (United States)

    Gill, Noel C.; Braden, Barbara T.

    Two way analyses of variance and cross-group descriptive comparisons assessed the effectiveness of the Siop Poison Prevention Program, which included an educational program and the use of warning labels, on improving verbal and visual discrimination of poisonous and nonpoisonous products for preschool children. The study sample consisted of 156…

  3. The Poison Control Center--Its Role

    Science.gov (United States)

    Manoguerra, Anthony S.

    1976-01-01

    Poison Control Centers are being utilized by more schools of pharmacy each year as training sites for students. This paper discusses what such a center is, its services, changes anticipated in the poison center system in the next several years and how they may influence pharmacy education, specifically as it relates to clinical toxicology.…

  4. Poison control center - Emergency number (image)

    Science.gov (United States)

    For a poison emergency call 1-800-222-1222 anywhere in the United States. This national hotline number will let you ... is a free and confidential service. All local poison control centers in the U.S. use this national ...

  5. Mercury poisoning | Shamley | South African Medical Journal

    African Journals Online (AJOL)

    The diagnosis of mercury poisoning requires a high index of suspicion. Mercury poisoning in a patient involved in illicit gold extraction is reported and 6 other cases considered. Some of the clinical features and treatment of this condition are discussed. S Afr Med J 1989; 76: 114-116 ...

  6. Non destructive evaluation of residual stresses in welding and hard-surfacing processes

    International Nuclear Information System (INIS)

    Suarez, J.C.; Fernandez, L.M.; Cruz, C.; Aragon, B.; Merino, F.

    1995-01-01

    In this paper transversal and longitudinal stress profiles in welding and hard-surfacing by welding processes are presented. The stresses were measured by RMS of Barkhausen signal. In this work it is shown that in each case the level of stresses is strongly dependent on the number of weld beads of surfacing layers deposited. The subsequent deposition of new weld beads or surfacing layers produces a stress-relieving effect

  7. Reduction of Surface Roughness by Means of Laser Processing over Additive Manufacturing Metal Parts.

    Science.gov (United States)

    Alfieri, Vittorio; Argenio, Paolo; Caiazzo, Fabrizia; Sergi, Vincenzo

    2016-12-31

    Optimization of processing parameters and exposure strategies is usually performed in additive manufacturing to set up the process; nevertheless, standards for roughness may not be evenly matched on a single complex part, since surface features depend on the building direction of the part. This paper aims to evaluate post processing treating via laser surface modification by means of scanning optics and beam wobbling to process metal parts resulting from selective laser melting of stainless steel in order to improve surface topography. The results are discussed in terms of roughness, geometry of the fusion zone in the cross-section, microstructural modification, and microhardness so as to assess the effects of laser post processing. The benefits of beam wobbling over linear scanning processing are shown, as heat effects in the base metal are proven to be lower.

  8. An Experimental Study of the Dropwise Condensation on Physically Processed Surface

    International Nuclear Information System (INIS)

    Choi, Jaeyoung; Chang, Soonheung; Watanabe, N.; Sambuichi, T.; Shiota, D.; Aritomi, M.

    2013-01-01

    Recent research by Kawakubo et al. derived empirical condensation heat transfer correlation suitable for wider range of operating condition in presence of non-condensable gas. However, their proposals of PCCS are focused on plane tube surface. To design better PCCS heat exchanger with high heat transfer coefficient new treatment on condensation surface can be considered in order to maintain dropwise condensation, the heat transfer coefficient of which has an order of magnitude larger than those of film condensation. Advanced research measure dropwise condensation heat transfer coefficient of Au and Cr coated surface based on number of droplet and droplet growth rate. However, coated surface is not desirable in power plant due to its duration of few years. On the other hand, physical processing (micro holes and patterns) on stainless steel and titanium surface is expected to perform better heat transfer, also is durable for the whole reactor lifetime. Since there is no published research about dropwise condensation for physically processed surface on SUS and Ti, the purposes of this research are to measure the condensation heat transfer coefficient and analyze its mechanism of enhanced heat transfer of treated SUS and Ti commonly used to nuclear plant. In the comparison of theoretical equation and experiment, it shows same result that heat transfer coefficient is proportional to maximum droplet diameter power to -0.321. Moreover, in the comparison of bare and processed surface, heat transfer coefficient decreases in processed surface

  9. Numerical study on formation process of helical nonneutral plasmas using electron injection from outside magnetic surfaces

    International Nuclear Information System (INIS)

    Nakamura, Kazutaka; Himura, Haruhiko; Masamune, Sadao; Sanpei, Akio; Isobe, Mitsutaka

    2009-01-01

    In order to investigate the formation process of helical nonneutral plasmas, we calculate the orbits of electron injected in the stochastic magnetic field when the closed helical magnetic surfaces is correspond with the equipotential surfaces. Contrary to the experimental observation, there are no electrons inward penetrating. (author)

  10. Upper Meter Processes: Short Wind Waves, Surface Flow, and Micro-Turbulence

    National Research Council Canada - National Science Library

    Jaehne, Bernd

    2000-01-01

    .... Since ground truth of the sea surface is still widely missing, a better understanding of the physics of these upper meter processes is of very important for the study of air-sea gas and momentum...

  11. Evaluation of optical functional surfaces on the injection moulding insert by micro milling process

    DEFF Research Database (Denmark)

    Li, Dongya; Davoudinejad, Ali; Zhang, Yang

    2017-01-01

    This study presents the optimization of micro milling process for manufacturing injection moulding inserts with an optical functionalsurface. The objective is the optimal surface functionality. Micro ridges were used as the microstructures to realize the function to generate contrast between...

  12. Cold pressure welding of aluminium-steel blanks: Manufacturing process and electrochemical surface preparation

    Science.gov (United States)

    Schmidt, Hans Christian; Homberg, Werner; Orive, Alejandro Gonzalez; Grundmeier, Guido; Hordych, Illia; Maier, Hans Jürgen

    2018-05-01

    In this study the manufacture of aluminium-steel blanks by cold pressure welding and their preparation for a welding process through electrochemical surface treatment are investigated and discussed. The cold pressure welding process was done with an incremental rolling tool that allows for the partial pressure welding of two blanks along a prepared path. The influence of the surface preparation by electrochemical deposition of bond promoting organosilane-based agents and roughening on a nano-scale is investigated and compared to conventional surface treatments. Coating the surfaces with a thin organosilane-based film incorporating specific functional groups should promote additional bonding between the mating oxide layers; its influence on the total weld strength is studied. Pressure welding requires suitable process strategies, and the current advances in the proposed incremental rolling process for the combination of mild steel and aluminium are presented.

  13. Simulation of dynamic processes when machining transition surfaces of stepped shafts

    Science.gov (United States)

    Maksarov, V. V.; Krasnyy, V. A.; Viushin, R. V.

    2018-03-01

    The paper addresses the characteristics of stepped surfaces of parts categorized as "solids of revolution". It is noted that in the conditions of transition modes during the switch to end surface machining, there is cutting with varied load intensity in the section of the cut layer, which leads to change in cutting force, onset of vibrations, an increase in surface layer roughness, a decrease of size precision, and increased wear of a tool's cutting edge. This work proposes a method that consists in developing a CNC program output code that allows one to process complex forms of stepped shafts with only one machine setup. The authors developed and justified a mathematical model of a technological system for mechanical processing with consideration for the resolution of tool movement at the stages of transition processes to assess the dynamical stability of a system in the process of manufacturing stepped surfaces of parts of “solid of revolution” type.

  14. Fabrication of superhydrophobic wood surfaces via a solution-immersion process

    Science.gov (United States)

    Liu, Changyu; Wang, Shuliang; Shi, Junyou; Wang, Chengyu

    2011-11-01

    Superhydrophobic wood surfaces were fabricated from potassium methyl siliconate (PMS) through a convenient solution-immersion method. The reaction involves a hydrogen bond assembly and a polycondensation process. The silanol was formed by reacting PMS aqueous solution with CO2, which was assembled on the wood surface via hydrogen bonds with the wood surface -OH groups. The polymethylsilsesquioxane coating was obtained through the polycondensation reaction of the hydroxyl between wood and silanol. The morphology of products were characterized using a scanning electron microscope (SEM), the surface chemical composition was determined using energy dispersive X-ray analysis (EDXA), Fourier transform infrared spectroscopy (FT-IR), thermogravimetry (TGA) and contact angle measurement. Analytical results revealed that rough protuberances uniformly covered the wood surface, thus transforming the wood surface from hydrophilic to superhydrophobic. The water contact angle of the superhydrophobic wood surface was about 153° and a sliding angle was 4.6°.

  15. Levothyroxine Poisoning - Symptoms and Clinical Outcome

    DEFF Research Database (Denmark)

    Nygaard, Birgitte; Saedder, Eva A; Dalhoff, Kim

    2015-01-01

    Levothyroxine (LT), T4, poisoning is rarely associated with a severe outcome. However, cases with significant complications have been reported. The aim of this study was to identify factors associated with symptoms of poisoning including late-onset symptoms. All enquiries to the Danish Poison...... Information Centre (DPIC) concerning LT poisoning between March 2007 and September 2012 were reviewed and the following parameters were recorded: age, dose, time from ingestion, multiple drug intake and symptoms. To evaluate the frequency of late-onset symptoms, a subgroup of patients without initial symptoms...... patients, neither in children nor in adults (age 16-92 years) (p poisoning at the time of enquiry; however, in 9 of 21 (43%) patients, we were able to contact, late-onset symptoms existed. In none of the cases...

  16. Poisoning of animals by industrial fumes

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, P

    1937-01-01

    Autopsy findings of game that died presumably due to poisoning by arsenic are presented. Corrosive gastroenteritis with edema and ecchymosis of the mucosa, and partly ulceration of the stomach, and fatty degeneration of the kidneys and liver were found in hares and stags. Arsenic was detected in the gastric content, liver, and other organs. These cases were diagnosed as acute to subacute poisoning by arsenic. Catarrhal gastrointestinal mucosa, pseudomembranes, in the esophagus, inflammatory edema of the nasal septum and laryngeai mucosa, and sometimes liver cirrhosis and edema of the spleen were found in red deer, roes, and hares. In these cases, poisoning by arsenic could not be identified as the primary cause of death. The symptoms of the poisoning were similar to cause of death. The symptoms of the poisoning were similar to those observed in game around a smelter prior to the installation of an efficient arsenic trap.

  17. Burnable poison fuel element and its fabrication

    International Nuclear Information System (INIS)

    Zukeran, Atsushi; Inoue, Kotaro; Aizawa, Hiroko.

    1985-01-01

    Purpose: To enable to optionally vary the excess reactivity and fuel reactivity. Method: Burnable poisons with a large neutron absorption cross section are contained in fuel material, by which the excess reactivity at the initial stage in the reactor is suppressed by the burnable poisons and the excess reactivity is released due to the reduction in the atomic number density of the burnable poisons accompanying the burning. The burnable poison comprises spherical or rod-like body made of a single material or spherical or rod-like member made of a plurality kind of materials laminated in a layer. These spheres or rods are dispersed in the fuel material. By adequately selecting the shape, combination and the arrangement of the burnable poisons, the axial power distribution of the fuel rods are flattened. (Moriyama, K.)

  18. The role of original surface roughness in laser-induced periodic surface structure formation process on poly-carbonate films

    International Nuclear Information System (INIS)

    Csete, M.; Hild, S.; Plettl, A.; Ziemann, P.; Bor, Zs.; Marti, O.

    2004-01-01

    Poly-carbonate films containing different types of original surface roughness were illuminated by a polarized ArF excimer laser beam having a fluence of 4 mJ/cm 2 . Atomic force microscopy was applied to study the laser-induced periodic surface structure formation process at 0 deg. , 30 deg. and 45 deg. angles of incidence. The effect of initial surface structures on the intensity distribution was investigated in cases of: (a) grains on oriented and amorphous thick films; (b) holes on thin spin-coated films; and (c) nanoparticles arranged along micrometer long sides of hexagons below the spin-coated films. The presence of the scattering objects caused symmetry breaking, if the samples were illuminated by oblique incident 's' polarized beam. The Fourier analysis of the AFM pictures has shown the competition of structures having different periods. The characteristic of the permanent surface patterns proved that the interference of the incoming beam and the beams scattered on previously existing structures is the LIPSS generating feedback process. Ring-shaped structures having 228 nm diameter were produced

  19. Effect of Surface Densification on the Microstructure and Mechanical Properties of Powder Metallurgical Gears by Using a Surface Rolling Process

    Directory of Open Access Journals (Sweden)

    Jingguang Peng

    2016-10-01

    Full Text Available Powder metallurgy (PM components are widely used in the auto industry due to the advantage of net-shape forming, low cost, and high efficiency. Still, usage of PM components is limited in the auto industry when encountering rigorous situations, like heavy load, due to lower strength, hardness, wear resistance, and other properties compared to wrought components due to the existence of massive pores in the PM components. In this study, through combining the powder metallurgy process and rolling process, the pores in the PM components were decreased and a homogenous densified layer was formed on the surface, which resulted in the enhancement of the strength, hardness, wear resistance, and other properties, which can expand its range of application. In this paper, we study the impact of different rolling feeds on the performance of the components’ surfaces. We found that with the increase of the rolling feed, the depth of the densified layer increased.

  20. Development of Statistical Process Control Methodology for an Environmentally Compliant Surface Cleaning Process in a Bonding Laboratory

    Science.gov (United States)

    Hutchens, Dale E.; Doan, Patrick A.; Boothe, Richard E.

    1997-01-01

    Bonding labs at both MSFC and the northern Utah production plant prepare bond test specimens which simulate or witness the production of NASA's Reusable Solid Rocket Motor (RSRM). The current process for preparing the bonding surfaces employs 1,1,1-trichloroethane vapor degreasing, which simulates the current RSRM process. Government regulations (e.g., the 1990 Amendments to the Clean Air Act) have mandated a production phase-out of a number of ozone depleting compounds (ODC) including 1,1,1-trichloroethane. In order to comply with these regulations, the RSRM Program is qualifying a spray-in-air (SIA) precision cleaning process using Brulin 1990, an aqueous blend of surfactants. Accordingly, surface preparation prior to bonding process simulation test specimens must reflect the new production cleaning process. The Bonding Lab Statistical Process Control (SPC) program monitors the progress of the lab and its capabilities, as well as certifies the bonding technicians, by periodically preparing D6AC steel tensile adhesion panels with EA-91 3NA epoxy adhesive using a standardized process. SPC methods are then used to ensure the process is statistically in control, thus producing reliable data for bonding studies, and identify any problems which might develop. Since the specimen cleaning process is being changed, new SPC limits must be established. This report summarizes side-by-side testing of D6AC steel tensile adhesion witness panels and tapered double cantilevered beams (TDCBs) using both the current baseline vapor degreasing process and a lab-scale spray-in-air process. A Proceco 26 inches Typhoon dishwasher cleaned both tensile adhesion witness panels and TDCBs in a process which simulates the new production process. The tests were performed six times during 1995, subsequent statistical analysis of the data established new upper control limits (UCL) and lower control limits (LCL). The data also demonstrated that the new process was equivalent to the vapor

  1. Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Haibo [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China); Song, Guolin [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Tang, Guoyi, E-mail: tanggy@mail.tsinghua.edu.cn [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China)

    2016-04-26

    The present work integrates 3D digital optical microscopy (OM), nano-indentation, X-ray diffraction (XRD), scanning electron microscopy (SEM) with electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) to systematically investigate the effect of electropulsing on the surface mechanical properties and microstructure of AISI 304 stainless steel during the ultrasonic surface rolling process (USRP). Compared with the original USRP, the introduction of electropulsing with optimal parameters can effectively facilitate surface crack healing and improve surface hardness and wear resistance dramatically, and the residual compressive stress is further enhanced. Meanwhile, more martensite phase and fewer deformation twins can be found in the strengthened layer. Rapid improvement of the surface mechanical properties should be attributed to the ultra-refined grains, accelerated martensitic phase transformation and suppressed deformation twining induced by the coupling effect of USRP and electropulsing. The high strain rate given by USRP, increased stacking fault energy and accelerated dislocation mobility caused by electropulsing are likely the primary intrinsic reasons for the observed phenomena.

  2. Determinants of U.S. poison center utilization.

    Science.gov (United States)

    Litovitz, Toby; Benson, Blaine E; Youniss, Jessica; Metz, Edward

    2010-06-01

    High poison center utilization has been associated with decreased emergency department usage and hospitalization rates. However, utilization requires awareness of the poison center. Penetrance, defined as the number of human poison exposures reported to a poison center per 1,000 population, has been used as a marker of poison center awareness. To identify factors that influence poison center penetrance to optimize the life- and cost-saving benefits of poison control centers. Human poison exposures that were reported to the National Poison Data System in 2001 were analyzed to identify and rank factors affecting poison center penetrance. Overall penetrance correlated with pediatric penetrance (R(2) = 0.75, p poison center that were already in or en route to a healthcare facility at the time of the call to the poison center (R(2) = 0.41, p poison center service populations were associated with lower penetrance (R(2) = 0.23, p poison center (multiple regression). Positive predictors included the percentage of the population younger than 5 years, the percentage of the adult population with a bachelor's degree, poison center certification, poison center educator FTEs (full time equivalents), Asian population percentage, and population density. The inverse correlation between pediatric penetrance and healthcare facility utilization supports prior observations of excessive healthcare utilization when a poison center is not called. Since race, language and distance are barriers to poison center utilization, and since healthcare utilization increases when poison center penetrance declines, low penetrance suggests a lack of awareness of the poison center rather than a low incidence of poisonings. Strategies to raise penetrance should be informed by an understanding of the barriers to utilization - language, Black/African American race, distance from the poison center, poverty, and lower education levels.

  3. [Rapeseed poisoning of wild herbivores].

    Science.gov (United States)

    Schmid, A; Schmid, H

    1992-06-01

    Beginning with the simultaneous occurrence of the first extensive sowing of 00-rape and local increased losses among hares and roe deer in Western Germany and Austria at the end of 1986, the clinical and morphological symptoms of rape poisoning are discussed. They consist of damage to endo- and epithelium, cell membranes, blood, liver and in the so called "rape-blindness". Subsequently, the most important toxic agents of rape including their metabolites are presented. They consist in alkenyl- and indolyl-glucosinolates, leading to isothiocyanates (mustard oils), thiocyanates or thiocyanate ions resp., nitriles and antithyroid agents (e.g. goitrin) as well as S-methylcysteine sulphoxide and its metabolites, particularly dimethyl disulphide. Finally, the activity spectrum of the toxic agents or the metabolites and the clinical picture of the affected wildlife in 1986 are compared with the result that the losses of that period are most likely to be traced back to rape poisoning and that the rape-blindness mentioned is to be interpreted as a thiocyanate-psychosis.

  4. Venomous and Poisonous Australian Animals of Veterinary Importance: A Rich Source of Novel Therapeutics

    Science.gov (United States)

    Allavena, Rachel E.

    2014-01-01

    Envenomation and poisoning by terrestrial animals (both vertebrate and invertebrate) are a significant economic problem and health risk for domestic animals in Australia. Australian snakes are some of the most venomous animals in the world and bees, wasps, ants, paralysis ticks, and cane toads are also present as part of the venomous and poisonous fauna. The diagnosis and treatment of envenomation or poisoning in animals is a challenge and can be a traumatic and expensive process for owners. Despite the potency of Australian venoms, there is potential for novel veterinary therapeutics to be modeled on venom toxins, as has been the case with human pharmaceuticals. A comprehensive overview of envenomation and poisoning signs in livestock and companion animals is provided and related to the potential for venom toxins to act as therapeutics. PMID:25143943

  5. Optimization of PWR fuel assembly radial enrichment and burnable poison location based on adaptive simulated annealing

    International Nuclear Information System (INIS)

    Rogers, Timothy; Ragusa, Jean; Schultz, Stephen; St Clair, Robert

    2009-01-01

    The focus of this paper is to present a concurrent optimization scheme for the radial pin enrichment and burnable poison location in PWR fuel assemblies. The methodology is based on the Adaptive Simulated Annealing (ASA) technique, coupled with a neutron lattice physics code to update the cost function values. In this work, the variations in the pin U-235 enrichment are variables to be optimized radially, i.e., pin by pin. We consider the optimization of two categories of fuel assemblies, with and without Gadolinium burnable poison pins. When burnable poisons are present, both the radial distribution of enrichment and the poison locations are variables in the optimization process. Results for 15 x 15 PWR fuel assembly designs are provided.

  6. Genetic Algorithm-Based Optimization for Surface Roughness in Cylindrically Grinding Process Using Helically Grooved Wheels

    Science.gov (United States)

    Çaydaş, Ulaş; Çelik, Mahmut

    The present work is focused on the optimization of process parameters in cylindrical surface grinding of AISI 1050 steel with grooved wheels. Response surface methodology (RSM) and genetic algorithm (GA) techniques were merged to optimize the input variable parameters of grinding. The revolution speed of workpiece, depth of cut and number of grooves on the wheel were changed to explore their experimental effects on the surface roughness of machined bars. The mathematical models were established between the input parameters and response by using RSM. Then, the developed RSM model was used as objective functions on GA to optimize the process parameters.

  7. Poorly processed reusable surface disinfection tissue dispensers may be a source of infection.

    Science.gov (United States)

    Kampf, Günter; Degenhardt, Stina; Lackner, Sibylle; Jesse, Katrin; von Baum, Heike; Ostermeyer, Christiane

    2014-01-21

    Reusable surface disinfectant tissue dispensers are used in hospitals in many countries because they allow immediate access to pre-soaked tissues for targeted surface decontamination. On the other hand disinfectant solutions with some active ingredients may get contaminated and cause outbreaks. We determined the frequency of contaminated surface disinfectant solutions in reusable dispensers and the ability of isolates to multiply in different formulations. Reusable tissue dispensers with different surface disinfectants were randomly collected from healthcare facilities. Solutions were investigated for bacterial contamination. The efficacy of two surface disinfectants was determined in suspension tests against two isolated species directly from a contaminated solution or after 5 passages without selection pressure in triplicate. Freshly prepared use solutions were contaminated to determine survival of isolates. 66 dispensers containing disinfectant solutions with surface-active ingredients were collected in 15 healthcare facilities. 28 dispensers from nine healthcare facilities were contaminated with approximately 107 cells per mL of Achromobacter species 3 (9 hospitals), Achromobacter xylosoxidans or Serratia marcescens (1 hospital each). In none of the hospitals dispenser processing had been adequately performed. Isolates regained susceptibility to the disinfectants after five passages without selection pressure but were still able to multiply in different formulations from different manufacturers at room temperature within 7 days. Neglecting adequate processing of surface disinfectant dispensers has contributed to frequent and heavy contamination of use-solutions based on surface active ingredients. Tissue dispenser processing should be taken seriously in clinical practice.

  8. Assessment of surface contamination level in an operating uranium ore processing facility of Jaduguda, India

    International Nuclear Information System (INIS)

    Meena, J.S.; Patnaik, R.L.; Jha, V.N.; Sahoo, S.K.; Ravi, P.M.; Tripathi, R.M.

    2014-01-01

    Radiological concern of the occupational workers and the area is given priority over other safety issue in confirmation with the stipulated guideline of national regulatory agency (AERB/FEFCF/SG-2, 2007). The key concern from the radiological hazard evaluation point of view is air activity, external gamma level and surface contamination. Present investigations was carried out to ascertain the surface contamination level of uranium ore processing facility at Jaduguda, Jharkhand. For a low grade uranium ore processing industry surface contamination is a major concern in product precipitation and recovery section. In view of this, the ore processing plant can broadly be classified into three areas i.e. ion exchange area, precipitation and product recovery section and other areas. The monitoring results incorporate the level of surface contamination of the plant during the last five years. The geometric mean activity of surface contamination level was 31.1, 34.5 and 9.8 Bq dm -2 in ion exchange, product precipitation and recovery and other areas with GSD of 2, 2.5 and 1.9. In most of the cases the surface contamination level was well within the recommended limit of 100 Bq dm -2 for M class uranium compound. Occasional cases of surface contamination levels exceeding the recommended limit were addressed and areas were decontaminated. Based on the study, modification in the design feature of the surface of the finished product section was also suggested so that the decontamination procedure can be more effectively implemented

  9. Processing method and processing device for liquid waste containing surface active agent and radioactive material

    International Nuclear Information System (INIS)

    Nishi, Takashi; Matsuda, Masami; Baba, Tsutomu; Yoshikawa, Ryozo; Yukita, Atsushi.

    1998-01-01

    Washing liquid wastes containing surface active agents and radioactive materials are sent to a deaerating vessel. Ozone is blown into the deaerating vessel. The washing liquid wastes dissolved with ozone are introduced to a UV ray irradiation vessel. UV rays are irradiated to the washing liquid wastes, and hydroxy radicals generated by photodecomposition of dissolved ozone oxidatively decompose surface active agents contained in the washing liquid wastes. The washing liquid wastes discharged from the UV ray irradiation vessel are sent to an activated carbon mixing vessel and mixed with powdery activated carbon. The surface active agents not decomposed in the UV ray irradiation vessel are adsorbed to the activated carbon. Then, the activated carbon and washing liquid wastes are separated by an activated carbon separating/drying device. Radioactive materials (iron oxide and the like) contained in the washing liquid wastes are mostly granular, and they are separated and removed from the washing liquid wastes in the activated carbon separating/drying device. (I.N.)

  10. Continuous processing of polymers in repetitively pulsed atmospheric pressure discharges with moving surfaces and gas flow

    Energy Technology Data Exchange (ETDEWEB)

    Bhoj, Ananth N [Department of Chemical and Biomolecular Engineering, University of Illinois, Urbana, IL 61801 (United States); Kushner, Mark J [Department of Electrical and Computer Engineering, Iowa State University, Ames, IA 50011 (United States)

    2007-11-21

    Atmospheric pressure corona discharges are industrially employed to treat large areas of commodity polymer sheets by creating new surface functional groups. The most common processes use oxygen containing discharges to affix oxygen to hydrocarbon polymers, thereby increasing their surface energy and wettability. The process is typically continuous and is carried out in a web configuration with film speeds of tens to hundreds of cm s{sup -1}. The densities and relative abundances of functional groups depend on the gas composition, gas flow rate and residence time of the polymer in the discharge zone which ultimately determine the magnitude and mole fractions of reactive fluxes to the surface. In this paper, results are discussed from a two-dimensional computational investigation of the atmospheric pressure plasma functionalization of a moving polypropylene sheet in repetitively pulsed He/O{sub 2}/H{sub 2}O discharges. O and OH typically initiate surface processing by hydrogen abstraction. These species are regenerated during every plasma pulse but are also largely consumed during the inter-pulse period. Longer-lived species such as O{sub 3} accumulate over many pulses and convect downstream with the gas flow. Optimizing the interplay between local rapid reactions, such as H abstraction which occurs dominantly in the discharge zone, and non-local slower processes, such as surface-surface reactions, may enable the customization of the relative abundance of surface functional groups.

  11. Continuous processing of polymers in repetitively pulsed atmospheric pressure discharges with moving surfaces and gas flow

    International Nuclear Information System (INIS)

    Bhoj, Ananth N; Kushner, Mark J

    2007-01-01

    Atmospheric pressure corona discharges are industrially employed to treat large areas of commodity polymer sheets by creating new surface functional groups. The most common processes use oxygen containing discharges to affix oxygen to hydrocarbon polymers, thereby increasing their surface energy and wettability. The process is typically continuous and is carried out in a web configuration with film speeds of tens to hundreds of cm s -1 . The densities and relative abundances of functional groups depend on the gas composition, gas flow rate and residence time of the polymer in the discharge zone which ultimately determine the magnitude and mole fractions of reactive fluxes to the surface. In this paper, results are discussed from a two-dimensional computational investigation of the atmospheric pressure plasma functionalization of a moving polypropylene sheet in repetitively pulsed He/O 2 /H 2 O discharges. O and OH typically initiate surface processing by hydrogen abstraction. These species are regenerated during every plasma pulse but are also largely consumed during the inter-pulse period. Longer-lived species such as O 3 accumulate over many pulses and convect downstream with the gas flow. Optimizing the interplay between local rapid reactions, such as H abstraction which occurs dominantly in the discharge zone, and non-local slower processes, such as surface-surface reactions, may enable the customization of the relative abundance of surface functional groups

  12. Auto-recognition of surfaces and auto-generation of material removal volume for finishing process

    Science.gov (United States)

    Kataraki, Pramod S.; Salman Abu Mansor, Mohd

    2018-03-01

    Auto-recognition of a surface and auto-generation of material removal volumes for the so recognised surfaces has become a need to achieve successful downstream manufacturing activities like automated process planning and scheduling. Few researchers have contributed to generation of material removal volume for a product but resulted in material removal volume discontinuity between two adjacent material removal volumes generated from two adjacent faces that form convex geometry. The need for limitation free material removal volume generation was attempted and an algorithm that automatically recognises computer aided design (CAD) model’s surface and also auto-generate material removal volume for finishing process of the recognised surfaces was developed. The surfaces of CAD model are successfully recognised by the developed algorithm and required material removal volume is obtained. The material removal volume discontinuity limitation that occurred in fewer studies is eliminated.

  13. Dominant rate process of silicon surface etching by hydrogen chloride gas

    International Nuclear Information System (INIS)

    Habuka, Hitoshi; Suzuki, Takahiro; Yamamoto, Sunao; Nakamura, Akio; Takeuchi, Takashi; Aihara, Masahiko

    2005-01-01

    Silicon surface etching and its dominant rate process are studied using hydrogen chloride gas in a wide concentration range of 1-100% in ambient hydrogen at atmospheric pressure in a temperature range of 1023-1423 K, linked with the numerical calculation accounting for the transport phenomena and the surface chemical reaction in the entire reactor. The etch rate, the gaseous products and the surface morphology are experimentally evaluated. The dominant rate equation accounting for the first-order successive reactions at silicon surface by hydrogen chloride gas is shown to be valid. The activation energy of the dominant surface process is evaluated to be 1.5 x 10 5 J mol - 1 . The silicon deposition by the gaseous by-product, trichlorosilane, is shown to have a negligible influence on the silicon etch rate

  14. Analysis of WEDM Process Parameters on Surface Roughness and Kerf using Taguchi Method

    Directory of Open Access Journals (Sweden)

    Asfana Banu

    2017-12-01

    Full Text Available In obtaining the best quality of engineering parts, the quality of machined surface plays an essential role. The fatigue strength, wear resistance, and corrosion of workpiece are some of the aspects of the qualities that can be improved. This paper investigates the effect of wire electrical discharge machining (WEDM process parameters on surface roughness and kerf on stainless steel using distilled water as dielectric fluid and brass wire as tool electrode. The selected process parameters are voltage open, wire speed, wire tension, voltage gap, and off time. Empirical models using Taguchi method were developed for the estimation of surface roughness and kerf. The analysis revealed that off time has major influence on surface roughness and kerf. The optimum machining parameters for minimum surface roughness and kerf were found to be 10 V open voltage, 2.84 µs off time, 12 m/min wire speed, 6.3 N wire tension, and 54.91 V voltage gap.

  15. Specifics of adsorption and chemical processes on the surface of gamma-irradiated vanadium dioxide

    International Nuclear Information System (INIS)

    Kaurkovskaya, V.N.; Dzyubenko, L.S.; Doroshenko, V.N.; Chujko, A.A.; Shakhov, A.P.

    2006-01-01

    Effect of γ-irradiation on electrophysical properties and processes of thermal desorption of water from the surface of vanadium oxides V 2 O 3 -VO 2-δ -VO 2+δ -V 2 O 5 was investigated by derivatography and electric conductivity. Content of adsorbed water at the surface and phase composition of the surface was demonstrated to change under the action of low radiation doses. Surface electric conductivity of the irradiated samples VO 2-δ in the process of chemical reactions of adsorbed following irradiation benzoic acid and ethanol was established to be much above than in irradiated-free ones. It is presumed that metal-semiconductor phase transition at the surface of VO 2-δ during chemical reaction is intensified by irradiation [ru

  16. Comparison of poisonings managed at military and Veterans Administration hospitals reported to Texas poison centers.

    Science.gov (United States)

    Forrester, M B

    2017-01-01

    There is little information on poisonings managed at military and Veterans Administration (VA) hospitals. This investigation described and compared poisonings reported to Texas poison centers that were managed at military and VA hospitals. Retrospective analysis of poison centre data. Cases were poisonings among patients aged 18 years or more reported to Texas poison centers during 2000-2015 where management occurred at a military or VA hospital. The distribution of exposures for various demographic and clinical factors was determined for military and veterans hospitals and comparisons were made between the two groups. There were 4353 and 1676 poisonings managed at military and VA hospitals, resepctively. Males accounted for 50.5% of the military hospital patients and 84.9% of the VA hospital patients. The mean age for military hospital patients was 31 years and for VA hospital patients was 50 years. The proportion of poisonings managed at military hospitals and VA hospitals, respectively, were intentional (70.0% vs 64.1%), particularly suspected attempted suicide (57.3% vs 47.7%), and unintentional (25.0% vs 30.5%). More than one substance was reported in 37.7% of military and 33.2% of VA hospital poisonings. The most commonly reported substance categories for poisonings managed at military and VA hospitals, respectively, were analgesics (28.4% vs 19.7%), sedatives/hypnotics/antipsychotics (24.7% vs 23.4%), antidepressants (18.7% vs 19.7%) and alcohol (11.3% vs 10.6%). A number of differences were observed between poisonings managed at military and VA hospitals. These differing patterns of poisonings may need to be taken into account in the education, prevention and treatment of poisonings at these hospitals and among the populations they serve. Copyright © 2016 The Royal Society for Public Health. Published by Elsevier Ltd. All rights reserved.

  17. Wildlife and the coal waste policy debate: proposed rules for coal waste disposal ignore lessons from 45 years of wildlife poisoning

    Science.gov (United States)

    A. Dennis Lemly; Joseph P. Skorupa

    2012-01-01

    This analysis examines wildlife poisoning from coal combustion waste (CCW) in the context of EPA's proposed policy that would allow continued use of surface impoundments as a disposal method. Data from 21 confirmed damage sites were evaluated, ranging from locations where historic poisoning has led to corrective actions that have greatly improved environmental...

  18. A model to improve the accuracy of US Poison Center data collection.

    Science.gov (United States)

    Krenzelok, E P; Reynolds, K M; Dart, R C; Green, J L

    2014-01-01

    Over 2 million human exposure calls are reported annually to United States regional poison information centers. All exposures are documented electronically and submitted to the American Association of Poison Control Center's National Poison Data System. This database represents the largest data source available on the epidemiology of pharmaceutical and non-pharmaceutical poisoning exposures. The accuracy of these data is critical; however, research has demonstrated that inconsistencies and inaccuracies exist. This study outlines the methods and results of a training program that was developed and implemented to enhance the quality of data collection using acetaminophen exposures as a model. Eleven poison centers were assigned randomly to receive either passive or interactive education to improve medical record documentation. A task force provided recommendations on educational and training strategies and the development of a quality-measurement scorecard to serve as a data collection tool to assess poison center data quality. Poison centers were recruited to participate in the study. Clinical researchers scored the documentation of each exposure record for accuracy. Results. Two thousand two hundred cases were reviewed and assessed for accuracy of data collection. After training, the overall mean quality scores were higher for both the passive (95.3%; + 1.6% change) and interactive intervention groups (95.3%; + 0.9% change). Data collection accuracy improved modestly for the overall accuracy score and significantly for the substance identification component. There was little difference in accuracy measures between the different training methods. Despite the diversity of poison centers, data accuracy, specifically substance identification data fields, can be improved by developing a standardized, systematic, targeted, and mandatory training process. This process should be considered for training on other important topics, thus enhancing the value of these data in

  19. Poisoning

    Science.gov (United States)

    ... mix household chemicals. Doing so can cause dangerous gases. Always store household chemicals in the container they ... 2018, A.D.A.M., Inc. Duplication for commercial use must be authorized in writing by ADAM ...

  20. Effect of conditioner load on the polishing pad surface during chemical mechanical planarization process

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Cheol Min; Qin, Hong Yi; Hong, Seok Jun; Jeon, Sang Hyuk; Kulkarni, Atul; Kim, Tae Sun [Sungkyunkwan University, Suwon (Korea, Republic of)

    2016-12-15

    During the Chemical mechanical planarization (CMP), the pad conditioning process can affect the pad surface characteristics. Among many CMP process parameters, the improper applied load on the conditioner arm may have adverse effects on the polyurethane pad. In this work, we evaluated the pad surface properties under the various conditioner arm applied during pad conditioning process. The conditioning pads were evaluated for surface topography, surface roughness parameters such as Rt and Rvk and Material removal rate (MRR) and within-wafer non-uniformity after wafer polishing. We observed that, the pad asperities were collapsed in the direction of conditioner rotation and blocks the pad pores applied conditioner load. The Rvk value and MRR were founded to be in relation with 4 > 1 > 7 kgF conditioner load. Hence, this study shows that, 4 kgF applied load by conditioner is most suitable for the pad conditioning during CMP.

  1. Unearthing poison use and consequent anecdotal vulture mortalities ...

    African Journals Online (AJOL)

    Aldicarb or carbofuran were the most commonly used poisons, but strychnine is still used by about one farmer out of 10. Poison is typically used by means of distributing poisoned baits in the landscape. Furthermore, willingness to use poison in the future was highest for farmers who own large properties with high livestock ...

  2. 49 CFR 172.416 - POISON GAS label.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false POISON GAS label. 172.416 Section 172.416... SECURITY PLANS Labeling § 172.416 POISON GAS label. (a) Except for size and color, the POISON GAS label... POISON GAS label and the symbol must be white. The background of the upper diamond must be black and the...

  3. 49 CFR 172.540 - POISON GAS placard.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false POISON GAS placard. 172.540 Section 172.540... SECURITY PLANS Placarding § 172.540 POISON GAS placard. (a) Except for size and color, the POISON GAS... the POISON GAS placard and the symbol must be white. The background of the upper diamond must be black...

  4. 16 CFR 1700.15 - Poison prevention packaging standards.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 2 2010-01-01 2010-01-01 false Poison prevention packaging standards. 1700.15 Section 1700.15 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION POISON PREVENTION PACKAGING ACT OF 1970 REGULATIONS POISON PREVENTION PACKAGING § 1700.15 Poison prevention packaging...

  5. Modeling for CO poisoning of a fuel cell anode

    Science.gov (United States)

    Dhar, H. P.; Kush, A. K.; Patel, D. N.; Christner, L. G.

    1986-01-01

    Poisoning losses in a half-cell in the 110-190 C temperature range have been measured in 100 wt pct H3PO4 for various mixtures of H2, CO, and CO2 gases in order to investigate the polarization loss due to poisoning by CO of a porous fuel cell Pt anode. At a fixed current density, the poisoning loss was found to vary linearly with ln of the CO/H2 concentration ratio, although deviations from linearity were noted at lower temperatures and higher current densities for high CO/H2 concentration ratios. The surface coverages of CO were also found to vary linearly with ln of the CO/H2 concentration ratio. A general adsorption relationship is derived. Standard free energies for CO adsorption were found to vary from -14.5 to -12.1 kcal/mol in the 130-190 C temperature range. The standard entropy for CO adsorption was found to be -39 cal/mol per deg K.

  6. Surface preparation process of a uranium titanium alloy, in particular for chemical nickel plating

    International Nuclear Information System (INIS)

    Henri, A.; Lefevre, D.; Massicot, P.

    1987-01-01

    In this process the uranium alloy surface is attacked with a solution of lithium chloride and hydrochloric acid. Dissolved uranium can be recovered from the solution by an ion exchange resin. Treated alloy can be nickel plated by a chemical process [fr

  7. Reactor scram device using fluid poison tubes

    International Nuclear Information System (INIS)

    Iwasaki, Toshio; Hasegawa, Koji.

    1979-01-01

    Purpose: To improve the response function in the reactor scram with no wide space by injecting poisons in soluble poison guide tubes to such a liquid level as giving no effect on usual reactor operation. Constitution: Soluble poison guide tubes in a reactor are connected at their upper ends to a buffer tank and at their lower ends to a pressurizer by way of a header and an injection valve. The header is connected by way of a valve with a level meter, one end of which is connected to the buffer tank. During reactor operation, the injection valve is closed and the soluble poisons in the pressurizer vessel is maintained at a pressurized state and, while on the other hand, soluble poisons are injected by way of the header to the lower end of the soluble poison guide tubes by the opening of a valve, which is thereafter closed. Upon scram, a valve is closed to protect the level meter and pressurized poisons are rapidly filled in the guide tubes by the release of the injection valve. (Kawakami, Y.)

  8. Surface modification on a glass surface with a combination technique of sol–gel and air brushing processes

    KAUST Repository

    Tsai, Meng-Yu; Hsu, Chin-Chi; Chen, Ping-Hei; Lin, Chao-Sung; Chen, Alexander

    2011-01-01

    This study fabricated the large area and optically transparent superhydrophobic silica based films on glass surface with optimized hardness. A silane coupling agent, tetraethoxysilane (TEOS), effectively bonds silica particles onto the glass substrate. Desired surface roughness was obtained by adjusting nano silica particles concentration of the precursors prepared by the sol-gel process. Silica suspension was coated onto the glass substrate by the air brushing methods. This method can deposit a uniform, transparent coating on the glass substrate efficiently. Diluting the precursor by adding ethanol or a mixture of D.I. water and ethanol further improved the transmittance and superhydrophobicity efficiency. The results showed that as the silica particle concentration and the thickness of the coating were increased, the surface roughness was enhanced. Rougher surface displayed a higher superhydrophobicity and lower transmittance. Therefore, the concentration of silica particle, volume of coatings, and the ratio of ethanol and D.I. water are of great importance to deposit a transparent, superhydrophobic coating on glass. © 2011 Elsevier B.V. All rights reserved.

  9. Surface modification on a glass surface with a combination technique of sol–gel and air brushing processes

    KAUST Repository

    Tsai, Meng-Yu

    2011-08-01

    This study fabricated the large area and optically transparent superhydrophobic silica based films on glass surface with optimized hardness. A silane coupling agent, tetraethoxysilane (TEOS), effectively bonds silica particles onto the glass substrate. Desired surface roughness was obtained by adjusting nano silica particles concentration of the precursors prepared by the sol-gel process. Silica suspension was coated onto the glass substrate by the air brushing methods. This method can deposit a uniform, transparent coating on the glass substrate efficiently. Diluting the precursor by adding ethanol or a mixture of D.I. water and ethanol further improved the transmittance and superhydrophobicity efficiency. The results showed that as the silica particle concentration and the thickness of the coating were increased, the surface roughness was enhanced. Rougher surface displayed a higher superhydrophobicity and lower transmittance. Therefore, the concentration of silica particle, volume of coatings, and the ratio of ethanol and D.I. water are of great importance to deposit a transparent, superhydrophobic coating on glass. © 2011 Elsevier B.V. All rights reserved.

  10. Clinical observation on parathion poisoning

    Energy Technology Data Exchange (ETDEWEB)

    Park, Heung Il; Kwun, Chung Sik [Chonnam University Medical School, Kwangju (Korea, Republic of)

    1972-09-15

    A total of 158 cases of parathion poisoning were clinically observed in Chonnam University Hospital from January, 1968 to June, 1972 with the following results. 1. The males were 133 and the females, 25 (radio, about 5:1) with 93 patients (58.9%) in the age group of 21 to 40 years old and the majority of the patients were farmers. 2. 158 cases could be divided into 38 cases of inhalation group (group I) and 120 cases of ingestion group (group II). The group I entirely occurred by accident during spraying the parathion, whereas the group II mostly developed by ingestion of the parathion for the suicide purpose. 3. During the period from 1968 to 1972, more frequent incidence of parathion poisoning showed up in 1971 and 1972. Inhalation group mostly occurred on July, August, and September, but several cases appeared sporadically in the rest of the months. 4. Most patients came to our Hospital within 4 hours after parathion poisoning and were discharged from the Hospital within one or two days after admission. Mortality was 2 cases (5.3%) out of 38 cases in inhalation group and was 26 cases (21.7%) out of 120 cases in ingestion group. 5. Clinical signs and symptoms showing high incidence were bronchorrhoea (incidence of 38.6%), dyspnea (57.6%), vomiting (62.0%), abdominal cramps (20.0%), sialorrhoea (53.8%), tachycardia (32.2%), miosis (67.7%), fasciculation (19.0%), hypertension (27.9%), drowsiness and confusion (50.0%), leukocytosis (58.3%), elevation of SGOT (23.0%), whereas mydriasis (5.7%), and proteinuria (4.0%) were low in incidence. All the ten cases (6.3%) showing involuntary defecation expired. 6. Roentgenographs of the chest were taken to 39 cases out of a total of 158 cases and revealed 21 cases (54.0%) of normal chest, 11 cases (28.0%) of bilateral pulmonary congestion, 7 cases (18.0%) of pulmonary edema or pneumonic consolidation.

  11. Topological characterization of antireflective and hydrophobic rough surfaces: are random process theory and fractal modeling applicable?

    Science.gov (United States)

    Borri, Claudia; Paggi, Marco

    2015-02-01

    The random process theory (RPT) has been widely applied to predict the joint probability distribution functions (PDFs) of asperity heights and curvatures of rough surfaces. A check of the predictions of RPT against the actual statistics of numerically generated random fractal surfaces and of real rough surfaces has been only partially undertaken. The present experimental and numerical study provides a deep critical comparison on this matter, providing some insight into the capabilities and limitations in applying RPT and fractal modeling to antireflective and hydrophobic rough surfaces, two important types of textured surfaces. A multi-resolution experimental campaign using a confocal profilometer with different lenses is carried out and a comprehensive software for the statistical description of rough surfaces is developed. It is found that the topology of the analyzed textured surfaces cannot be fully described according to RPT and fractal modeling. The following complexities emerge: (i) the presence of cut-offs or bi-fractality in the power-law power-spectral density (PSD) functions; (ii) a more pronounced shift of the PSD by changing resolution as compared to what was expected from fractal modeling; (iii) inaccuracy of the RPT in describing the joint PDFs of asperity heights and curvatures of textured surfaces; (iv) lack of resolution-invariance of joint PDFs of textured surfaces in case of special surface treatments, not accounted for by fractal modeling.

  12. Laser processing of metallic biomaterials: An approach for surface patterning and wettability control

    Science.gov (United States)

    Razi, Sepehr; Mollabashi, Mahmoud; Madanipour, Khosro

    2015-12-01

    Q -switched Nd:YAG laser is used to manipulate the surface morphology and wettability characteristic of 316L stainless steel (SS) and titanium biomaterials. Water and glycerol are selected as wettability testing liquids and the sessile drop method is used for the contact angle measurements. Results indicate that on both of the metals, wettability toward water improves significantly after the laser treatment. Different analyses including the study of the surface morphology, free energy and oxidation are assessed in correlation with wettability. Beside the important role of the laser-induced surface patterns, the increase in the surface roughness, oxygen content and the polar component of the surface energy, are detected as the most important physical and chemical phenomena controlling the improvement in the wettability. However, all the processed hydrophilic surfaces that are exposed to air become hydrophobic over time. The time dependency of the surface wettability is related to the chemical activities on the treated surfaces and the reduction of oxygen/carbon (O/C) ratio on them. The behavior is further studied with investigating the effect of the keeping environment and changes of the components of the surface tension. Results show that the pulsed laser treatment is a versatile approach to create either hydrophobic or super hydrophilic surfaces for industrial and medical applications.

  13. Effects of Micromachining Processes on Electro-Osmotic Flow Mobility of Glass Surfaces

    Directory of Open Access Journals (Sweden)

    Norihisa Miki

    2013-03-01

    Full Text Available Silica glass is frequently used as a device material for micro/nano fluidic devices due to its excellent properties, such as transparency and chemical resistance. Wet etching by hydrofluoric acid and dry etching by neutral loop discharge (NLD plasma etching are currently used to micromachine glass to form micro/nano fluidic channels. Electro-osmotic flow (EOF is one of the most effective methods to drive liquids into the channels. EOF mobility is affected by a property of the micromachined glass surfaces, which includes surface roughness that is determined by the manufacturing processes. In this paper, we investigate the effect of micromaching processes on the glass surface topography and the EOF mobility. We prepared glass surfaces by either wet etching or by NLD plasma etching, investigated the surface topography using atomic force microscopy, and attempted to correlate it with EOF generated in the micro-channels of the machined glass. Experiments revealed that the EOF mobility strongly depends on the surface roughness, and therefore upon the fabrication process used. A particularly strong dependency was observed when the surface roughness was on the order of the electric double layer thickness or below. We believe that the correlation described in this paper can be of great help in the design of micro/nano fluidic devices.

  14. Fission product poisoning in KS-150 reactor operation

    International Nuclear Information System (INIS)

    Rana, S.B.

    1978-01-01

    A three-dimensional model of the KS-150 reactor was used to study reactivity changes induced by reactor poisoning with fission products Xe 135 and Sm 149 . A comparison of transients caused by the poisoning showed the following differences: (1) the duration of the transient Xe poisoning (2 days) is shorter by one order of magnitude than the duration of Sm poisoning (20 days); however, the level of Xe poisoning is greater approximately by one order than the level of the Sm poisoning; (2) the level of steady-state Xe poisoning depends on the output level of the reactor; steady-state Sm poisoning does not depend on this level; (3) following reactor shutdown Xe poisoning may increase to the maximum value of up to Δrhosub(Xe)=20% and will then gradually decrease; Sm poisoning may reach maximum values of up to Δrhosub(Sm)=2% and does not decrease. (J.B.)

  15. Tropical fish poisoning in temperate climates: food poisoning from ciguatera toxin presenting in Avonmouth.

    Science.gov (United States)

    Kipping, Ruth; Eastcott, Howard; Sarangi, Joyshri

    2006-12-01

    Ciguatera toxin causes a range of gastrointestinal, cardiovascular and neurological symptoms that occur within 1-6 h of ingesting fish with the toxin and can last for days, months or years. It is a well-recognized problem in the tropics. Avon Health Protection Team investigated food poisoning on a ship at Avonmouth, which was thought by the crew to be related to a white snapper fish from the Caribbean. The symptoms were initially thought to be scombroid fish poisoning but were consistent with ciguatera fish poisoning. Cases of fish poisoning from fish imported from the Caribbean and Pacific or travellers returning from tropical countries may be ciguatera fish poisoning, but mistakenly diagnosed as scombroid fish poisoning.

  16. Effect of processing parameters of rotary ultrasonic machining on surface integrity of potassium dihydrogen phosphate crystals

    Directory of Open Access Journals (Sweden)

    Jianfu Zhang

    2015-09-01

    Full Text Available Potassium dihydrogen phosphate is an important optical crystal. However, high-precision processing of large potassium dihydrogen phosphate crystal workpieces is difficult. In this article, surface roughness and subsurface damage characteristics of a (001 potassium dihydrogen phosphate crystal surface produced by traditional and rotary ultrasonic machining are studied. The influence of process parameters, including spindle speed, feed speed, type and size of sintered diamond wheel, ultrasonic power, and selection of cutting fluid on potassium dihydrogen phosphate crystal surface integrity, was analyzed. The surface integrity, especially the subsurface damage depth, was affected significantly by the ultrasonic power. Metal-sintered diamond tools with high granularity were most suitable for machining potassium dihydrogen phosphate crystal. Cutting fluid played a key role in potassium dihydrogen phosphate crystal machining. A more precise surface can be obtained in machining with a higher spindle speed, lower feed speed, and using kerosene as cutting fluid. Based on the provided optimized process parameters for machining potassium dihydrogen phosphate crystal, a processed surface quality with Ra value of 33 nm and subsurface damage depth value of 6.38 μm was achieved.

  17. Optimization of CO2 Laser Cutting Process using Taguchi and Dual Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    M. Madić

    2014-09-01

    Full Text Available Selection of optimal cutting parameter settings for obtaining high cut quality in CO2 laser cutting process is of great importance. Among various analytical and experimental optimization methods, the application of Taguchi and response surface methodology is one of most commonly used for laser cutting process optimization. Although the concept of dual response surface methodology for process optimization has been used with success, till date, no experimental study has been reported in the field of laser cutting. In this paper an approach for optimization of CO2 laser cutting process using Taguchi and dual response surface methodology is presented. The goal was to determine the near optimal laser cutting parameter values in order to ensure robust condition for minimization of average surface roughness. To obtain experimental database for development of response surface models, Taguchi’s L25 orthogonal array was implemented for experimental plan. Three cutting parameters, the cutting speed (3, 4, 5, 6, 7 m/min, the laser power (0.7, 0.9, 1.1, 1.3, 1.5 kW, and the assist gas pressure (3, 4, 5, 6, 7 bar, were used in the experiment. To obtain near optimal cutting parameters settings, multi-stage Monte Carlo simulation procedure was performed on the developed response surface models.

  18. Paraphenylenediamine Poisoning in Tunisia: A Case Report

    Directory of Open Access Journals (Sweden)

    Dorra Amira

    2015-05-01

    Full Text Available Paraphenylenediamine (PPD represents the main active substance in the color of hair dyes. In Tunisia, PPD poisoning is very common, especially in rural areas where the consequences linked to this toxic substance are still unknown. In this paper, we report a case of PPD poisoning and confirm the diagnosis by a qualitative method of analysis. We discuss the clinical manifestations and study the kinetics of biological parameters during the monitoring of the poisoning. The main complication was renal failure and the treatment was basically symptomatic.

  19. Fatal poisoning among patients with drug addiction

    DEFF Research Database (Denmark)

    Simonsen, Kirsten Wiese; Christoffersen, Dorte J; Banner, Jytte

    2015-01-01

    INTRODUCTION: Fatal poisonings among drug addicts in Denmark in 2012 were examined. Cause of death, abuse pattern and geographic differences are discussed and data are compared with previous studies. METHODS: All fatal poisonings examined at the three institutes of forensic medicine in Denmark...... on Funen and in South Jutland. Cocaine was most frequently detected in East Denmark, while amphetamine was more frequent in West Denmark. CONCLUSIONS: The number of fatal poisonings among drug addicts has stabilised around 200. The increase in methadone deaths continued and, as in 2007, methadone...... with 2007, indicating that a considerable number of drug addicts also have psychiatric illness. FUNDING: none. TRIAL REGISTRATION: not relevant....

  20. Fatal poisoning among patients with drug addiction

    DEFF Research Database (Denmark)

    Simonsen, K. W.; Christoffersen, D. J.; Banner, J.

    2015-01-01

    Introduction: Fatal poisonings among drug addicts in Denmark in 2012 were examined. Cause of death, abuse pattern and geographic differences are discussed and data are compared with previous studies. Methods: All fatal poisonings examined at the three institutes of forensic medicine in Denmark...... on Funen and in South Jutland. Cocaine was most frequently detected in East Denmark, while amphetamine was more frequent in West Denmark. ConclusionS: The number of fatal poisonings among drug addicts has stabilised around 200. The increase in methadone deaths continued and, as in 2007, methadone...... with 2007, indicating that a considerable number of drug addicts also have psychiatric illness....

  1. Intractable Seizures and Rehabilitation in Ciguatera Poisoning.

    Science.gov (United States)

    Derian, Armen; Khurana, Seema; Rothenberg, Joshua; Plumlee, Charles

    2017-05-01

    Ciguatera fish poisoning is the most frequently reported seafood toxin illness associated with the ingestion of contaminated tropical fish. Diagnosis relies on a history of recent tropical fish ingestion and subsequent development of gastrointestinal, cardiovascular, and neurological symptoms. Ciguatera poisoning usually has a self-limited time course, and its management involves symptomatic control and supportive care. This case report presents an uncommon case of ciguatera poisoning with prolonged intractable seizures refractory to standard antiseizure medications. The patient also had significant functional decline that responded to rigorous inpatient rehabilitation not previously described in literature.

  2. Delayed encephalopathy after acute carbon monoxide poisoning

    Directory of Open Access Journals (Sweden)

    Mehmet İbrahim Turan

    2014-03-01

    Full Text Available Carbon monoxide poisoning is a major cause of death following attempted suicide and accidental exposures. Although clinical presentation depends on the duration and the intensity of exposure, the assessment of the severity of intoxication is difficult. A small percentage of patients who show complete initial recovery may develop delayed neurological deficits. Delayed encephalopathy after acute carbon monoxide poisoning is a rare and poor prognosis neurologic disorders and there is no specific treatment. We present a case with early onset of delayed encephalopathy after acute carbon monoxide poisoning with typical cranial imaging findings in a child with atypical history and clinical presentation.

  3. Acute selenium poisoning in cattle

    Energy Technology Data Exchange (ETDEWEB)

    Shortridge, E H; O' Hara, P J; Marshall, P M

    1971-01-01

    Three hundred and seventy-six (67%) of 557 calves of approximately 150-200 kg live-weight died following subcutaneous injection of a solution containing 100 mg selenium as sodium selenite. Eight per cent of the 254 heifer calves and 56% of the 303 steers died. The calves had endured the stress of being weaned twice and held in stockyards twice as well as encountering wet weather during the 4 days before receiving the selenium. The heifer calves were also vaccinated with Br. abortus strain 19 vaccine at the same time as receiving the selenium. The clinical signs and pathological findings of circulatory failure and myocardial damage were similar to those previously reported in acute selenium poisoning.

  4. Lead poisoning in small animals

    Energy Technology Data Exchange (ETDEWEB)

    Scott, H M

    1963-08-17

    During the period 1957 to 1959 a considerable number of dogs were seen which were suffering from colic. Colic is not normally a condition commonly encountered in the dog, and the number of cases seen was large in proportion to the number of dogs in the population concerned. A number of other dogs exhibited nervous signs which varied from symptoms of mild anxiety to exaggerated fits. There was a certain amount of overlapping between the 2 groups in that some cases which originally only showed signs of colic later progressed to the stage where they showed nervous symptoms. The following report deals with 28 cases of lead poisoning in dogs and cats which occurred at Broken Hill, Northern Rhodesia. 8 references, 4 tables.

  5. Extracorporeal Treatment for Salicylate Poisoning

    DEFF Research Database (Denmark)

    Juurlink, David N; Gosselin, Sophie; Kielstein, Jan T

    2015-01-01

    in poisoning. We conducted a systematic literature review followed by data extraction and summarized findings, following a predetermined format. The entire work group voted by a 2-round modified Delphi method to reach consensus on voting statements, using a RAND/UCLA Appropriateness Method to quantify...... disagreement. Anonymous votes were compiled, returned, and discussed in person. A second vote determined the final recommendations. RESULTS: Eighty-four articles met inclusion criteria, including 1 controlled clinical trial, 3 animal studies, and 80 case reports or case series, yielding an overall very low...... quality of evidence for all recommendations. Clinical data on 143 patients (130 sets of which could be analyzed for patient-level entry data), including 14 fatalities, were reviewed. Toxicokinetic data on 87 patients were also included. After the second round of voting, the workgroup concluded...

  6. Evaluation and control of poisoning of impregnated carbons used for organic iodide removal

    International Nuclear Information System (INIS)

    Kovach, J.L.; Rankovic, L.

    1979-01-01

    By the evaluation of the chemical reactions which have taken place on impregnated activated carbon surfaces exposed to nuclear reactor atmospheric environments, the role of various impregnants has been studied. The evaluation shows several different paths for the aging and posioning to take place. The four major causes were found to be: organic solvent contamination; inorganic acid gas contamination; formation of organic acids on carbon surface; and, formation of SO 2 from carbon sulfur content. Prevention of poisoning by the first two paths can be accomplished only by procedural changes within the facility. However the last three poisoning paths can be controlled to some extent by the selection of carbon pretreatment techniques and the type of impregnant used. Results were generated by evaluating used carbons from 14 nuclear power plants and by artificial poisoning of laboratory impregnated carbons. Impregnants which have antioxidant properties, besides reaction with organic iodides, can increase the life of the impregnated activated carbons

  7. Animal poisoning - veterinary-medical and criminal-legal aspects

    Directory of Open Access Journals (Sweden)

    Aleksić Jelena

    2014-01-01

    Full Text Available Apart from approved or planned poisoning with agricultural purpose, an increase in the number of cases of intentional animal poisoning (primarily referring to cats and dogs has been detected in Serbia, and it is suspected that their number is significantly larger than the one shown by the official statistics data. Under the conditions prescribed by the Criminal Code of the Republic of Serbia, such activities may represent the crime of killing and torture of animals, but also the crime of causing a general danger. It would be impossible to conduct the procedure of discovering and proving these criminal offences and the responsibility of their perpetrators without findings and opinion of forensic veterinary-medicine experts. They play an important role when it comes to site inspection, crime scene processing, collecting the samples from the crime scene, processing of samples and autopsy and exhumation of a potentially poisoned animal body. Just like other evidence in criminal procedure, findings and opinion of experts of veterinary medicine are estimated in accordance with the principle of free assessment of evidence. However, due to the specificity of such cases of killing and torture of animals, their impact on court’s decision on the existence of criminal offence and perpetrator’s liability is crucial. In this paper, the authors discuss the scope of animal poisoning in Serbia, particularly in Belgrade, analyze possible criminal - legal consequences of these illegal activities and point out to a significant role that experts of veterinary medical profession have in discovering and proving such cases and the liability of their perpetrators.

  8. Acute pesticide poisoning and pesticide registration in Central America

    International Nuclear Information System (INIS)

    Wesseling, Catharina; Corriols, Marianela; Bravo, Viria

    2005-01-01

    The International Code of Conduct on the Distribution and Use of Pesticides of the Food and Agriculture Organization (FAO) of the United Nations has been for 20 years the most acknowledged international initiative for reducing negative impact from pesticide use in developing countries. We analyzed pesticide use and poisoning in Central America, particularly in Costa Rica and Nicaragua, and evaluated whether registration decisions are based on such data, in accordance with the FAO Code. Extensive use of very hazardous pesticides continues in Central America and so do poisonings with organophosphates, carbamates, endosulfan and paraquat as the main causative agents. Central American governments do not carry out or commission scientific risk assessments. Instead, guidelines from international agencies are followed for risk management through the registration process. Documentation of pesticide poisonings during several decades never induced any decision to ban or restrict a pesticide. However, based on the official surveillance systems, in 2000, the ministers of health of the seven Central American countries agreed to ban or restrict twelve of these pesticides. Now, almost 4 years later, restrictions have been implemented in El Salvador and in Nicaragua public debate is ongoing. Chemical and agricultural industries do not withdraw problematic pesticides voluntarily. In conclusion, the registration processes in Central America do not comply satisfactorily with the FAO Code. However, international regulatory guidelines are important in developing countries, and international agencies should strongly extend its scope and influence, limiting industry involvement. Profound changes in international and national agricultural policies, steering towards sustainable agriculture based on non-chemical pest management, are the only way to reduce poisonings

  9. Chronic copper poisoning in lambs

    Energy Technology Data Exchange (ETDEWEB)

    Ross, D B

    1964-08-08

    This communication presented evidence of the elevation of plasma GOT (glutamic oxaloacetic transaminase or aspartate transaminase) concentration during the development of copper toxicity in some experimental lambs, and also demonstrated that plasma GOT concentration can be used to assess the course of the disease during treatment. A group of Kerry Hill lambs were fed 1 1/2 lb per day of a proprietary concentrate containing 40 parts of copper per million on a dry-matter basis in addition to hay and water ad lib. Data was included for the plasma GOT concentrations of the lambs, bled weekly after weaning from pasture to this diet. There was some variation between the individual lambs, and in one there was no increase in plasma GOT by the 20th week when all the surviving lambs were slaughtered. The concentrations of copper found in the caudate lobe of the liver and in the kidney cortex post mortem were given. The overall findings showed that the liver gave a reliable indication of the copper status of an animal whereas the kidney cortex copper concentration was a better criterion for the diagnosis of copper poisoning and was in agreement with the results of Eden, Todd, and Grocey and Thompson. Observations demonstrated the benefits resulting from the early diagnosis of chronic copper poisoning in lambs, when treatment of affected animals may be commenced before the haemolytic crisis develops. Treatment included reducing the copper intake and dosing with ammonium molybdate and sodium sulfate, and the plasma GOT concentration may be used to assess the rate of recovery. 4 references, 3 tables.

  10. Process comparison for fracture-induced formation of surface structures on polymer films

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yueh-Ying [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Yang, Fuqian [Department of Chemical and Materials Engineering, University of Kentucky, Lexington, KY 40506 (United States); Chen, Chia-Chieh [Institute of Nuclear Energy Research, Longtan, Taoyuan 32546, Taiwan (China); Lee, Sanboh, E-mail: sblee@mx.nthu.edu.tw [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan (China)

    2014-01-01

    Using three different splitting approaches such as point-load splitting, tension-splitting and peeling–splitting, different surface ripples were produced on poly(methyl methacrylate) (PMMA)-based polymer films. Independent of the splitting approaches, the spatial wavelength of the surface structures is a linear function of the film thickness with the approximately same differential ratio of the spatial wavelength to the film thickness. The apparent surface residual stress was calculated from the thickness dependence of the spatial frequency, and the magnitude of the apparent surface stress increased with the increase of the film thickness. After exposing the aged PMMA-based photoresist at liquid state to gamma-irradiation, the effects of aging and the gamma-irradiation were investigated on the splitting-induced formation of surface structures. For the peeling–splitting process, the differential ratio of the spatial wavelength to the film thickness for the aged samples is larger than that for non-aged samples. The point-load splitting could not produce any surface pattern on the gamma-irradiated films. None of the splitting approaches could form surface structures for polymer films exposed to irradiation of high dose. Both the spatial wavelength and the apparent surface stress increased with the film thickness for the irradiated polymer films. - Highlights: • Using splitting processes, surface ripples were formed on polymer films. • The surface ripples were induced by compressively apparent surface stress. • The spatial wavelength of the ripples is a linear function of the film thickness. • The spatial wavelength of the ripples is affected by gamma-ray irradiation. • The spatial wavelength of the ripples is affected by aging.

  11. Distribution and Characteristics of Boulder Halos at High Latitudes on Mars: Ground Ice and Surface Processes Drive Surface Reworking

    Science.gov (United States)

    Levy, J. S.; Fassett, C. I.; Rader, L. X.; King, I. R.; Chaffey, P. M.; Wagoner, C. M.; Hanlon, A. E.; Watters, J. L.; Kreslavsky, M. A.; Holt, J. W.; Russell, A. T.; Dyar, M. D.

    2018-02-01

    Boulder halos are circular arrangements of clasts present at Martian middle to high latitudes. Boulder halos are thought to result from impacts into a boulder-poor surficial unit that is rich in ground ice and/or sediments and that is underlain by a competent substrate. In this model, boulders are excavated by impacts and remain at the surface as the crater degrades. To determine the distribution of boulder halos and to evaluate mechanisms for their formation, we searched for boulder halos over 4,188 High Resolution Imaging Science Experiment images located between 50-80° north and 50-80° south latitude. We evaluate geological and climatological parameters at halo sites. Boulder halos are about three times more common in the northern hemisphere than in the southern hemisphere (19% versus 6% of images) and have size-frequency distributions suggesting recent Amazonian formation (tens to hundreds of millions of years). In the north, boulder halo sites are characterized by abundant shallow subsurface ice and high thermal inertia. Spatial patterns of halo distribution indicate that excavation of boulders from beneath nonboulder-bearing substrates is necessary for the formation of boulder halos, but that alone is not sufficient. Rather, surface processes either promote boulder halo preservation in the north or destroy boulder halos in the south. Notably, boulder halos predate the most recent period of near-surface ice emplacement on Mars and persist at the surface atop mobile regolith. The lifetime of observed boulders at the Martian surface is greater than the lifetime of the craters that excavated them. Finally, larger minimum boulder halo sizes in the north indicate thicker icy soil layers on average throughout climate variations driven by spin/orbit changes during the last tens to hundreds of millions of years.

  12. Effect of Space Radiation Processing on Lunar Soil Surface Chemistry: X-Ray Photoelectron Spectroscopy Studies

    Science.gov (United States)

    Dukes, C.; Loeffler, M.J.; Baragiola, R.; Christoffersen, R.; Keller, J.

    2009-01-01

    Current understanding of the chemistry and microstructure of the surfaces of lunar soil grains is dominated by a reference frame derived mainly from electron microscopy observations [e.g. 1,2]. These studies have shown that the outermost 10-100 nm of grain surfaces in mature lunar soil finest fractions have been modified by the combined effects of solar wind exposure, surface deposition of vapors and accretion of impact melt products [1,2]. These processes produce surface-correlated nanophase Feo, host grain amorphization, formation of surface patinas and other complex changes [1,2]. What is less well understood is how these changes are reflected directly at the surface, defined as the outermost 1-5 atomic monolayers, a region not easily chemically characterized by TEM. We are currently employing X-ray Photoelectron Spectroscopy (XPS) to study the surface chemistry of lunar soil samples that have been previously studied by TEM. This work includes modification of the grain surfaces by in situ irradiation with ions at solar wind energies to better understand how irradiated surfaces in lunar grains change their chemistry once exposed to ambient conditions on earth.

  13. Analysis the complex interaction among flexible nanoparticles and materials surface in the mechanical polishing process

    Energy Technology Data Exchange (ETDEWEB)

    Han Xuesong, E-mail: hanxuesongphd@yahoo.com.cn [School of Mechanical Engineering, Tianjin University, 300072 (China); Gan, Yong X. [Department of Mechanical, Industrial and Manufacturing Engineering, University of Toledo, OH 43606 (United States)

    2011-02-01

    Mechanical polishing (MP), being the important technique of realizing the surface planarization, has already been widely applied in the area of microelectronic manufacturing and computer manufacturing technology. The surface planarization in the MP is mainly realized by mechanical process which depended on the microdynamic behavior of nanoparticle. The complex multibody interaction among nanoparticles and materials surface is different from interaction in the macroscopic multibody system which makes the traditional classical materials machining theory cannot accurately uncover the mystery of the surface generation in the MP. Large-scale classical molecular dynamic (MD) simulation of interaction among nanoparticles and solid surface has been carried out to investigate the physical essence of surface planarization. The particles with small impact angle can generate more uniform global planarization surface but the materials removal rate is lower. The shear interaction between particle and substrate may induce large friction torque and lead to the rotation of particle. The translation plus rotation makes the nanoparticle behaved like micro-milling tool. The results show that the nanoparticles may aggregrate together and form larger cluster thus deteriorate surface the quality. This MD simulation results illuminate that the f inal planarized surface can only be acquired by synergic behavior of all particles using various means such as cutting, impacting, scratching, indentation and so on.

  14. AFM surface imaging of AISI D2 tool steel machined by the EDM process

    International Nuclear Information System (INIS)

    Guu, Y.H.

    2005-01-01

    The surface morphology, surface roughness and micro-crack of AISI D2 tool steel machined by the electrical discharge machining (EDM) process were analyzed by means of the atomic force microscopy (AFM) technique. Experimental results indicate that the surface texture after EDM is determined by the discharge energy during processing. An excellent machined finish can be obtained by setting the machine parameters at a low pulse energy. The surface roughness and the depth of the micro-cracks were proportional to the power input. Furthermore, the AFM application yielded information about the depth of the micro-cracks is particularly important in the post treatment of AISI D2 tool steel machined by EDM

  15. AFM surface imaging of AISI D2 tool steel machined by the EDM process

    Science.gov (United States)

    Guu, Y. H.

    2005-04-01

    The surface morphology, surface roughness and micro-crack of AISI D2 tool steel machined by the electrical discharge machining (EDM) process were analyzed by means of the atomic force microscopy (AFM) technique. Experimental results indicate that the surface texture after EDM is determined by the discharge energy during processing. An excellent machined finish can be obtained by setting the machine parameters at a low pulse energy. The surface roughness and the depth of the micro-cracks were proportional to the power input. Furthermore, the AFM application yielded information about the depth of the micro-cracks is particularly important in the post treatment of AISI D2 tool steel machined by EDM.

  16. Method for atmospheric pressure reactive atom plasma processing for surface modification

    Science.gov (United States)

    Carr, Jeffrey W [Livermore, CA

    2009-09-22

    Reactive atom plasma processing can be used to shape, polish, planarize and clean the surfaces of difficult materials with minimal subsurface damage. The apparatus and methods use a plasma torch, such as a conventional ICP torch. The workpiece and plasma torch are moved with respect to each other, whether by translating and/or rotating the workpiece, the plasma, or both. The plasma discharge from the torch can be used to shape, planarize, polish, and/or clean the surface of the workpiece, as well as to thin the workpiece. The processing may cause minimal or no damage to the workpiece underneath the surface, and may involve removing material from the surface of the workpiece.

  17. Manipulating surface wettability and oil absorbency of diatomite depending on processing and ambient conditions

    Science.gov (United States)

    Özen, İlhan; Şimşek, Süleyman; Okyay, Gamze

    2015-03-01

    In this study, a diatomite sample, which is a natural inorganic mineral with inherently high water and oil absorption capacity, was subjected to grinding before surface modification. Afterwards, the diatomite surface was modified via facile methods using a fluorocarbon (FC) chemical and stearic acid (SA) in addition to the sol-gel fluorosilanization (FS) process. The water and oil wettability, and oil absorbency properties of the unmodified and modified diatomites were investigated in addition to diatomite characterizations such as chemical content, surface area, particle size distribution, morphology, and modification efficiency. It was revealed that the wettability was changed completely depending on the surface modification agent and the media used, while the oil absorbency property surprisingly did not change. On the other hand, the oil absorbency was worsened by the grinding process, whereas the wettability was not affected.

  18. Depletion optimization of lumped burnable poisons in pressurized water reactors

    International Nuclear Information System (INIS)

    Kodah, Z.H.

    1982-01-01

    Techniques were developed to construct a set of basic poison depletion curves which deplete in a monotonical manner. These curves were combined to match a required optimized depletion profile by utilizing either linear or non-linear programming methods. Three computer codes, LEOPARD, XSDRN, and EXTERMINATOR-2 were used in the analyses. A depletion routine was developed and incorporated into the XSDRN code to allow the depletion of fuel, fission products, and burnable poisons. The Three Mile Island Unit-1 reactor core was used in this work as a typical PWR core. Two fundamental burnable poison rod designs were studied. They are a solid cylindrical poison rod and an annular cylindrical poison rod with water filling the central region.These two designs have either a uniform mixture of burnable poisons or lumped spheroids of burnable poisons in the poison region. Boron and gadolinium are the two burnable poisons which were investigated in this project. Thermal self-shielding factor calculations for solid and annular poison rods were conducted. Also expressions for overall thermal self-shielding factors for one or more than one size group of poison spheroids inside solid and annular poison rods were derived and studied. Poison spheroids deplete at a slower rate than the poison mixture because each spheroid exhibits some self-shielding effects of its own. The larger the spheroid, the higher the self-shielding effects due to the increase in poison concentration

  19. The study of sub-surface damage distributions during grinding process on different abrasion materials

    Science.gov (United States)

    Kuo, Ching-Hsiang; Huang, Chien-Yao; Yu, Zong-Ru; Shu, Shyu-Cheng; Chang, Keng-Shou; Hsu, Wei-Yao

    2017-10-01

    The grinding process is the primary technology for curvature generation (CG) on glass optics. The higher material removal rate (MRR) leads to deeper sub-surface damage (SSD) on lens surface. The SSD must be removed by following lapping and polishing processes to ensure the lens quality. However, these are not an easy and an efficient process to remove the SSD from ground surface directly for aspheric surfaces with tens or hundreds microns departure from bestfit- sphere (BFS). An efficient fabrication procedure for large aspheric departure on glass materials must be considered. We propose 3-step fabrication procedures for aspheric surface with larger departure. 1st step is to generate a specific aspheric surface with depth less than 10 μm of SSD residual. 2nd step is to remove SSD and keep the aspheric form by using Zeeko polisher with higher MRR pad. Final step is to figure and finish the aspheric surface by using QED MRF machine. In this study, we focus on the 1st step to investigate the residual depth of SSD after grinding process on different abrasion materials. The materials of tested part are fused silica, S-NPH2, and S-PHM52. The cross grinding would be configured and depth of SSD/surface roughness would be evaluated in this study. The characteristic of SSD could be observed after etching by confocal microscope. The experimental results show the depth of SSD below 31.1 μm with #400 grinding wheel. And the near 10 μm depth of SSD would be achieved with #1,000 grinding wheel. It means the aspherization polishing on large parts with large departure from best fit sphere would be replaced. The fabrication of large aspheric part would be efficient.

  20. Influence of Wire Electrical Discharge Machining (WEDM) process parameters on surface roughness

    Science.gov (United States)

    Yeakub Ali, Mohammad; Banu, Asfana; Abu Bakar, Mazilah

    2018-01-01

    In obtaining the best quality of engineering components, the quality of machined parts surface plays an important role. It improves the fatigue strength, wear resistance, and corrosion of workpiece. This paper investigates the effects of wire electrical discharge machining (WEDM) process parameters on surface roughness of stainless steel using distilled water as dielectric fluid and brass wire as tool electrode. The parameters selected are voltage open, wire speed, wire tension, voltage gap, and off time. Empirical model was developed for the estimation of surface roughness. The analysis revealed that off time has a major influence on surface roughness. The optimum machining parameters for minimum surface roughness were found to be at a 10 V open voltage, 2.84 μs off time, 12 m/min wire speed, 6.3 N wire tension, and 54.91 V voltage gap.

  1. Effect of Build Angle on Surface Properties of Nickel Superalloys Processed by Selective Laser Melting

    Science.gov (United States)

    Covarrubias, Ernesto E.; Eshraghi, Mohsen

    2018-03-01

    Aerospace, automotive, and medical industries use selective laser melting (SLM) to produce complex parts through solidifying successive layers of powder. This additive manufacturing technique has many advantages, but one of the biggest challenges facing this process is the resulting surface quality of the as-built parts. The purpose of this research was to study the surface properties of Inconel 718 alloys fabricated by SLM. The effect of build angle on the surface properties of as-built parts was investigated. Two sets of sample geometries including cube and rectangular artifacts were considered in the study. It was found that, for angles between 15° and 75°, theoretical calculations based on the "stair-step" effect were consistent with the experimental results. Downskin surfaces showed higher average roughness values compared to the upskin surfaces. No significant difference was found between the average roughness values measured from cube and rectangular test artifacts.

  2. Insights into the Surface Transformation and Electrochemical Dissolution Process of Bornite in Bioleaching

    Directory of Open Access Journals (Sweden)

    Hongbo Zhao

    2018-04-01

    Full Text Available In this work, density functional theory (DFT calculations, X-ray photoelectron spectroscopy (XPS and electrochemistry analysis were combined to analyze the electrochemical dissolution process of bornite during bioleaching. DFT calculations showed that bornite was a conductor with metallic conductivity. The formula of bornite may be (Cu+5Fe3+(S2−4 and the surface reconstruction of (111-S surface was discussed. Electrochemistry and XPS analysis showed that bornite tended to be directly oxidized with high conductivity when the potential was higher than 0.3 V vs. Ag/AgCl. Elemental sulfur (S0, FeOOH and CuS were the main intermediate species on the bornite surface during the oxidation process. The production of S0 and FeOOH on bornite surface can be significantly accelerated with increased redox potential, but no insoluble sulfate (SO42− formed on bornite surface in 0.3–0.65 V vs. Ag/AgCl. The oxidative dissolution of bornite was significantly accelerated with increasing redox potential, which was one important reason why mixed culture was more effective than single strains of A. caldus and L. ferriphilum in bornite bioleaching. The insoluble SO42− was formed mainly through the chemical reactions in solution and then covered the bornite surface in bioleaching. Based on the obtained results, a model for interpreting the dissolution process of bornite in bioleaching was proposed.

  3. Land Surface Process and Air Quality Research and Applications at MSFC

    Science.gov (United States)

    Quattrochi, Dale; Khan, Maudood

    2007-01-01

    This viewgraph presentation provides an overview of land surface process and air quality research at MSFC including atmospheric modeling and ongoing research whose objective is to undertake a comprehensive spatiotemporal analysis of the effects of accurate land surface characterization on atmospheric modeling results, and public health applications. Land use maps as well as 10 meter air temperature, surface wind, PBL mean difference heights, NOx, ozone, and O3+NO2 plots as well as spatial growth model outputs are included. Emissions and general air quality modeling are also discussed.

  4. Bioinspired superhydrophobic surfaces, fabricated through simple and scalable roll-to-roll processing.

    Science.gov (United States)

    Park, Sung-Hoon; Lee, Sangeui; Moreira, David; Bandaru, Prabhakar R; Han, InTaek; Yun, Dong-Jin

    2015-10-22

    A simple, scalable, non-lithographic, technique for fabricating durable superhydrophobic (SH) surfaces, based on the fingering instabilities associated with non-Newtonian flow and shear tearing, has been developed. The high viscosity of the nanotube/elastomer paste has been exploited for the fabrication. The fabricated SH surfaces had the appearance of bristled shark skin and were robust with respect to mechanical forces. While flow instability is regarded as adverse to roll-coating processes for fabricating uniform films, we especially use the effect to create the SH surface. Along with their durability and self-cleaning capabilities, we have demonstrated drag reduction effects of the fabricated films through dynamic flow measurements.

  5. Evaporation phase change processes of water/methanol mixtures on superhydrophobic nanostructured surfaces

    Science.gov (United States)

    Chiang, Cheng-Kun; Lu, Yen-Wen

    2011-07-01

    Evaporation phenomena are a critical and frequently seen phase change process in many heat transfer applications. In this paper, we study the evaporation process of a sessile droplet on two topologically different surfaces, including smooth and nanostructured surfaces. The nanostructured surface has an array of high-aspect-ratio nanowires (height/diameter ~ 125) and is implemented by using a simple template-based nanofabrication method. It possesses superhydrophobicity (>140°) and low contact angle hysteresis (1.2-2.1°), allowing the liquid droplets to remain in the 'fakir' state throughout the evaporation processes. Sessile droplets of deionized (DI) water and water/methanol binary mixture test liquids with their contact angles and base diameters are monitored. The results show that the nanostructures play a critical role in the droplet dynamics during evaporation.

  6. Evaporation phase change processes of water/methanol mixtures on superhydrophobic nanostructured surfaces

    International Nuclear Information System (INIS)

    Chiang, Cheng-Kun; Lu, Yen-Wen

    2011-01-01

    Evaporation phenomena are a critical and frequently seen phase change process in many heat transfer applications. In this paper, we study the evaporation process of a sessile droplet on two topologically different surfaces, including smooth and nanostructured surfaces. The nanostructured surface has an array of high-aspect-ratio nanowires (height/diameter ∼ 125) and is implemented by using a simple template-based nanofabrication method. It possesses superhydrophobicity (>140°) and low contact angle hysteresis (1.2–2.1°), allowing the liquid droplets to remain in the 'fakir' state throughout the evaporation processes. Sessile droplets of deionized (DI) water and water/methanol binary mixture test liquids with their contact angles and base diameters are monitored. The results show that the nanostructures play a critical role in the droplet dynamics during evaporation

  7. Selection Criteria and Methods for Testing Different Surface Materials for Contact Frying Processes

    DEFF Research Database (Denmark)

    Ashokkumar, Saranya

    Inner surfaces of industrial process equipment for food are often coated to give the surfaces particular properties with respect to adhesion and cleanability. Existing coating materials (PTFE (Teflon®) or silicone based polymers) suffer from drawbacks when used in contact frying, because these co...... surface materials for contact frying processes. The surfaces selected for this purpose cover a wide spectrum of materials that range from hydrophobic to hydrophilic materials. The different surface materials investigated include stainless steel (reference), aluminium (Al Mg 5754), PTFE......, an experimental rig has been constructed which enabled a controlled fouling of different coatings on steel and aluminium substrates under realistic frying conditions. A subjective rating procedure was employed for screening different surfaces according to their non-stick properties when used for frying of a model...... defects and surface roughness play a significant role. The wear resistance of the coatings was tested by performing abrasive wear experiments. The ceramic coatings: TiAlN and ZrN were found to show the best wear resistance properties. The experiments also revealed the poor wear resistance of stainless...

  8. Drug Poisoning Mortality by State: United States

    Data.gov (United States)

    U.S. Department of Health & Human Services — This dataset describes drug poisoning deaths at the U.S. and state level by selected demographic characteristics, and includes age-adjusted death rates for drug...

  9. Hemlock (Conium Maculatum Poisoning In A Child

    Directory of Open Access Journals (Sweden)

    Capan KONCA

    2014-03-01

    Full Text Available Poison hemlock (Conium maculatum is a plant that is poisonous for humans and animals. Accidental ingestion of the plant may result in central nervous system depression, respiratory failure, acute rhabdomyolysis, acute renal failure and even death. The main treatment of hemlock poisoning is supportive care. The case of a 6-year-old girl who was admitted to the emergency department with complaints of burning sensation in mouth, hypersalivation, tremor in hands and ataxia after ingestion of poison hemlock is presented here with clinical and laboratory features. In this case, we aim to report that accidental ingestion of plants resembling vegetables that are consumed daily can lead to serious complications and even death.

  10. Drug Poisoning Mortality by County: United States

    Data.gov (United States)

    U.S. Department of Health & Human Services — This dataset describes drug poisoning deaths at the U.S. and state level by selected demographic characteristics, and includes age-adjusted death rates for drug...

  11. Nicotiana glauca poisoning in ostriches (Struthio camelus)

    CSIR Research Space (South Africa)

    Botha, CJ

    2011-01-01

    Full Text Available Putative Nicotiana glauca (wild tobacco) poisoning was diagnosed in a flock of ostriches near Oudtshoorn, South Africa. Post mortem examinations (n = 7) were performed on ostriches (Struthio camelus) that had died. Suspicious leaf remnants (weighing...

  12. Lead poisoning in a Mississippi sandhill crane

    Science.gov (United States)

    Franson, J. Christian; Hereford, Scott G.

    1994-01-01

    Lead poisoning from the ingestion of spent lead shot is well documented in waterfowl (Sanderson and Bellrose 1986) and has been reported in other wetland (Locke et al. 1991, Windingstad et al. 1984) and upland (Hunter and Rosen 1965, Locke and Bagley 1967) avian species. Ingested fishing weights have been implicated in lead poisoning of Trumpeter Swans (Cygnus buccinator) (Blus et al. 1989), Common Loons (Gavia immer) (Locke et al. 1982, Franson and Cliplef 1992, Pokras and Chafe1 1992), Mute Swans (Cygnus olor) (Birkhead 1982), and Sandhill Cranes (Grus canadensis) (Windingstad et al. 1984). The significance of lead poisoning as a mortality factor in avian species other than waterfowl is probably underestimated (Locke and Friend 1992), and any cause of mortality becomes particularly important in species with small population sizes. We report here the first known case of lead poisoning in a Mississippi Sandhill Crane (Grus canadensis pulla), a critically endangered subspecies.

  13. Extracorporeal treatment for tricyclic antidepressant poisoning

    DEFF Research Database (Denmark)

    Yates, Christopher; Galvao, Tais; Sowinski, Kevin M

    2014-01-01

    The Extracorporeal Treatments In Poisoning (EXTRIP) workgroup was formed to provide recommendations on the use of extracorporeal treatments (ECTR) in poisoning. Here, the workgroup presents its results for tricyclic antidepressants (TCAs). After an extensive literature search, using a predefined...... methodology, the subgroup responsible for this poison reviewed the articles, extracted the data, summarized findings, and proposed structured voting statements following a predetermined format. A two-round modified Delphi method was chosen to reach a consensus on voting statements and RAND...... yielding a very low quality of evidence for all recommendations. Data on 108 patients, including 12 fatalities, were abstracted. The workgroup concluded that TCAs are not dialyzable and made the following recommendation: ECTR is not recommended in severe TCA poisoning (1D). The workgroup considers...

  14. Intensive Care Management of Organophosphate Poisoned Patient ...

    African Journals Online (AJOL)

    Introduction. Pesticide poisonings remain a serious public .... prevent or increase threshold for the development of seizure, which ... Nigeria. Procurement of consumables and equipment ... enormous financial burden on them often leading to.

  15. Amitraz, an underrecognized poison: A systematic review

    Directory of Open Access Journals (Sweden)

    Sahajal Dhooria

    2016-01-01

    Results: The original search yielded 239 articles, of which 52 articles described human cases. After following the inclusion and exclusion criteria, 32 studies describing 310 cases (151 females, 175 children of human poisoning with amitraz were included in this systematic review. The most commonly reported clinical features of amitraz poisoning were altered sensorium, miosis, hyperglycaemia, bradycardia, vomiting, respiratory failure, hypotension and hypothermia. Amitraz poisoning carried a good prognosis with only six reported deaths (case fatality rate, 1.9%. Nearly 20 and 11.9 per cent of the patients required mechanical ventilation and inotropic support, respectively. The role of decontamination methods, namely, gastric lavage and activated charcoal was unclear. Interpretation & conclusions: Our review shows that amitraz is an important agent for accidental or suicidal poisoning in both adults and children. It has a good prognosis with supportive management.

  16. Mercury Poisoning Linked to Skin Products

    Science.gov (United States)

    ... Products For Consumers Home For Consumers Consumer Updates Mercury Poisoning Linked to Skin Products Share Tweet Linkedin ... and, in some situations, criminal prosecution. Dangers of Mercury Exposure to mercury can have serious health consequences. ...

  17. Cutting system for burnable poison rod

    International Nuclear Information System (INIS)

    Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

    1989-01-01

    Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

  18. The EXTRIP (EXtracorporeal TReatments In Poisoning) workgroup

    DEFF Research Database (Denmark)

    Lavergne, Valéry; Nolin, Thomas D; Hoffman, Robert S

    2012-01-01

    Extracorporeal treatments (ECTRs), such as hemodialysis and hemoperfusion, are used in poisoning despite a lack of controlled human trials demonstrating efficacy. To provide uniform recommendations, the EXTRIP group was formed as an international collaboration among recognized experts from...

  19. Carbon monoxide poisoning: Medical students' knowledge towards ...

    African Journals Online (AJOL)

    , and poisonous gas produced by incomplete combustion of organic materials. It is particularly dangerous as it cannot be detected by man's natural sense organs. There is hardly a month without one or two newspaper reports of death ...

  20. Erbium: alternative poison? stabilisation additive? what future?

    International Nuclear Information System (INIS)

    Porta, J.; Asou, M.

    2001-01-01

    Erbium was proposed as alternative poison to gadolinium at a very early stage. The potential interest of this poison compared to gadolinium is that it presents a relatively low ( 167 Er) absorption cross section in the thermal range and a non-negligible resonance integral that lead to a relatively slow consumption kinetic rather adapted to long or even very long cycles. The poisoning mode adapted to this poison, homogeneous in low concentration (< 3 %), does not downgrade the power distribution, on the one hand, as the absorption is low and spatially homogeneous, and the thermal conductivity, on the other hand, as the addition in the fuel oxide is in low quantity. A review of knowledge acquired as regards Er, from the 1960's to now, is presented. (authors)

  1. Planarization of the diamond film surface by using the hydrogen plasma etching with carbon diffusion process

    International Nuclear Information System (INIS)

    Kim, Sung Hoon

    2001-01-01

    Planarization of the free-standing diamond film surface as smooth as possible could be obtained by using the hydrogen plasma etching with the diffusion of the carbon species into the metal alloy (Fe, Cr, Ni). For this process, we placed the free-standing diamond film between the metal alloy and the Mo substrate like a metal-diamond-molybdenum (MDM) sandwich. We set the sandwich-type MDM in a microwave-plasma-enhanced chemical vapor deposition (MPECVD) system. The sandwich-type MDM was heated over ca. 1000 .deg. C by using the hydrogen plasma. We call this process as the hydrogen plasma etching with carbon diffusion process. After etching the free-standing diamond film surface, we investigated surface roughness, morphologies, and the incorporated impurities on the etched diamond film surface. Finally, we suggest that the hydrogen plasma etching with carbon diffusion process is an adequate etching technique for the fabrication of the diamond film surface applicable to electronic devices

  2. Basic visual perceptual processes in children with typical development and cerebral palsy: The processing of surface, length, orientation, and position.

    Science.gov (United States)

    Schmetz, Emilie; Magis, David; Detraux, Jean-Jacques; Barisnikov, Koviljka; Rousselle, Laurence

    2018-03-02

    The present study aims to assess how the processing of basic visual perceptual (VP) components (length, surface, orientation, and position) develops in typically developing (TD) children (n = 215, 4-14 years old) and adults (n = 20, 20-25 years old), and in children with cerebral palsy (CP) (n = 86, 5-14 years old) using the first four subtests of the Battery for the Evaluation of Visual Perceptual and Spatial processing in children. Experiment 1 showed that these four basic VP processes follow distinct developmental trajectories in typical development. Experiment 2 revealed that children with CP present global and persistent deficits for the processing of basic VP components when compared with TD children matched on chronological age and nonverbal reasoning abilities.

  3. Ciguatera poisoning in the Cook Islands.

    Science.gov (United States)

    Bailey, Stephanie; Withers, Tristan

    2014-06-25

    This case report presents two British medical students who contracted ciguatera poisoning while on elective in the Cook Islands. Thirty-six hours after consuming two reef fish they developed paraesthesia of the mouth, hands and feet, myalgia, pruritis and cold allodynia. Neurological examination was normal. Diagnosis of ciguatera poisoning was made on history of reef fish consumption and classical clinical presentation. Management was symptomatic (antihistamines) and both students made a full recovery within 10 weeks. 2014 BMJ Publishing Group Ltd.

  4. Vital Signs-Alcohol Poisoning Deaths

    Centers for Disease Control (CDC) Podcasts

    2015-01-06

    This podcast is based on the January 2015 CDC Vital Signs report. In the United States, an average of six people die every day from alcohol poisoning. Learn what you can do to prevent binge drinking and alcohol poisoning.  Created: 1/6/2015 by National Center for Chronic Disease Prevention and Health Promotion (NCCDPHP).   Date Released: 1/6/2015.

  5. Brachiaria spp. poisoning of ruminants in Brazil

    OpenAIRE

    B. Riet-Correa; M.B. Castro; R.A. Lemos; G. Riet-Correa; V. Mustafa; F. Riet-Correa

    2011-01-01

    Brachiaria species are the most important grasses for cattle production in Brazil. However, a limiting factor for the use of Brachiaria spp. is their toxicity. Most outbreaks of hepatogenous photosensitization are caused by B. decumbens; however B. brizantha, B. humidicola and B. ruziziensis can also cause poisoning. The poisoning affects cattle, sheep, goats and buffalo. Sheep are more susceptible than other animal species and the young are more susceptible than adults. There are differences...

  6. Management of acute organophosphorus pesticide poisoning

    OpenAIRE

    Eddleston, Michael; Buckley, Nick A; Eyer, Peter; Dawson, Andrew H

    2008-01-01

    Summary Organophosphorus pesticide self-poisoning is an important clinical problem in rural regions of the developing world, and kills an estimated 200?000 people every year. Unintentional poisoning kills far fewer people but is a problem in places where highly toxic organophosphorus pesticides are available. Medical management is difficult, with case fatality generally more than 15%. We describe the limited evidence that can guide therapy and the factors that should be considered when design...

  7. Acute pesticide poisoning: a proposed classification tool

    OpenAIRE

    Thundiyil, Josef G; Stober, Judy; Besbelli, Nida; Pronczuk, Jenny

    2008-01-01

    Cases of acute pesticide poisoning (APP) account for significant morbidity and mortality worldwide. Developing countries are particularly susceptible due to poorer regulation, lack of surveillance systems, less enforcement, lack of training and inadequate access to information systems. Previous research has demonstrated wide variability in incidence rates for APP. This is possibly due to inconsistent reporting methodology and exclusion of occupational and non-intentional poisonings. The purpo...

  8. Pharmacological treatment of cardiac glycoside poisoning

    OpenAIRE

    Roberts, Darren M.; Gallapatthy, Gamini; Dunuwille, Asunga; Chan, Betty S.

    2015-01-01

    Cardiac glycosides are an important cause of poisoning, reflecting their widespread clinical usage and presence in natural sources. Poisoning can manifest as varying degrees of toxicity. Predominant clinical features include gastrointestinal signs, bradycardia and heart block. Death occurs from ventricular fibrillation or tachycardia. A wide range of treatments have been used, the more common including activated charcoal, atropine, ??adrenoceptor agonists, temporary pacing, anti?digoxin Fab a...

  9. Accidental poisoning with detomidine and butorphanol.

    Science.gov (United States)

    Hannah, N

    2010-09-01

    This is a case report concerning a veterinarian who spilled detomidine and butorphanol on dermatitic hands while sedating a horse. This resulted in acute poisoning from which the patient spontaneously recovered with supportive management. Veterinarians often suffer from occupational dermatitis and handle strong sedatives with no gloves while working around unpredictable animals. Thus, this group is at risk of accidental self-poisoning from this method.

  10. Hair dye poisoning and the developing world

    Directory of Open Access Journals (Sweden)

    Sampathkumar Krishnaswamy

    2009-01-01

    Full Text Available Hair dye poisoning has been emerging as one of the important causes of intentional self harm in the developing world. Hair dyes contain paraphenylene-diamine and a host of other chemicals that can cause rhabdomyolysis, laryngeal edema, severe metabolic acidosis and acute renal failure. Intervention at the right time has been shown to improve the outcome. In this article, we review the various manifestations, clinical features and treatment modalities for hair dye poisoning.

  11. Acute hexogen poisoning after occupational exposure.

    Science.gov (United States)

    Testud, F; Glanclaude, J M; Descotes, J

    1996-01-01

    Hexogen (cyclonite, RDX) nitrate explosive is an infrequent cause of poisoning. A 42-year-old man with no prior history of epilepsy experienced grand mal seizures after sieving fine hexogen (RDX) powder for four hours in an ammunition plant. Physical examination was normal on arrival at the emergency room but recurrent seizures occurred six hour after admission. EEG, CT scan and MRI were normal and the patient recovered uneventfully. The available toxicological data on this rare occupational poisoning are reviewed.

  12. Cartap poisoning: A rare case report.

    Science.gov (United States)

    Kumar, A S Praveen; Amalnath, Deepak; Dutta, T K

    2011-10-01

    Cartap is a pesticide commonly used to control weevil and caterpillars. It is an analogue of nereistoxin, a neurotoxic substance isolated from the marine annelid Lumbriconereis heteropoda. It causes neuromuscular blockade. Poisoning with cartap is very rare and not yet reported from India. We report a 35-year-old lady with cartap poisoning who presented with nausea, vomiting, and dyspnea. She improved with N-acetyl cysteine and symptomatic management.

  13. Cartap poisoning: A rare case report

    OpenAIRE

    Kumar, A. S. Praveen; Amalnath, Deepak; Dutta, T. K.

    2011-01-01

    Cartap is a pesticide commonly used to control weevil and caterpillars. It is an analogue of nereistoxin, a neurotoxic substance isolated from the marine annelid Lumbriconereis heteropoda. It causes neuromuscular blockade. Poisoning with cartap is very rare and not yet reported from India. We report a 35-year-old lady with cartap poisoning who presented with nausea, vomiting, and dyspnea. She improved with N-acetyl cysteine and symptomatic management.

  14. Low reactivity penalty burnable poison rods

    International Nuclear Information System (INIS)

    1978-01-01

    A nuclear reactor burnable poison rod is described which consists of an elongated tubular sheath enclosing a neutron absorbing material which, at least during reactor operation, also encloses a neutron moderating material. The excess reactivity existing at the beginning of core life is compensated for by the depletion of the burnable poison throughout the life of the core, so that the life of the core is extended. (UK)

  15. Microstructure and optical appearance of anodized friction stir processed Al - Metal oxide surface composites

    DEFF Research Database (Denmark)

    Gudla, Visweswara Chakravarthy; Jensen, Flemming; Bordo, Kirill

    2014-01-01

    Multiple-pass friction stir processing (FSP) was employed to impregnate Ti, Y and Ce oxide powders into the surface of an Aluminium alloy. The FSP processed surface composite was subsequently anodized with an aim to develop optical effects in the anodized layer owing to the presence of incorporated...... oxide particles which will influence the scattering of light. This paper presents the investigations on relation between microstructure of the FSP zone and optical appearance of the anodized layer due to incorporation of metal oxide particles and modification of the oxide particles due to the anodizing...

  16. Lead poisoning in opium abuser in Iran: A systematic review

    Directory of Open Access Journals (Sweden)

    Kambiz Soltaninejad

    2018-01-01

    Full Text Available Substance abuse and its consequences are major health hazards in the world. Opium addiction is a common form of substance abuse in Iran. Adulteration of illegal substances in the process of production and distribution of the drug in black market with many types of materials have been reported. One of the main goals of the adulteration of illegal substances is cutting of the substance for deal and increase of the weight for more benefit. However, adding of adulterating agents to illegal drugs could be considered as a cause of nonspecific and rare toxicity during substance abuse. Although the presence of lead in street-level heroin, marijuana, and amphetamines has been reported from some countries previously, recently, several reports suggested lead poisoning in Iranian opium addicts. Adulteration of opium with lead is a new source of lead poisoning in Iran in which the opium abuse is frequent and it could be a new health problem in the future. In this regard, evaluation of blood lead level would be important for early diagnosis of lead poisoning in opium addicts.

  17. Lead Poisoning in Opium Abuser in Iran: A Systematic Review

    Science.gov (United States)

    Soltaninejad, Kambiz; Shadnia, Shahin

    2018-01-01

    Substance abuse and its consequences are major health hazards in the world. Opium addiction is a common form of substance abuse in Iran. Adulteration of illegal substances in the process of production and distribution of the drug in black market with many types of materials have been reported. One of the main goals of the adulteration of illegal substances is cutting of the substance for deal and increase of the weight for more benefit. However, adding of adulterating agents to illegal drugs could be considered as a cause of nonspecific and rare toxicity during substance abuse. Although the presence of lead in street-level heroin, marijuana, and amphetamines has been reported from some countries previously, recently, several reports suggested lead poisoning in Iranian opium addicts. Adulteration of opium with lead is a new source of lead poisoning in Iran in which the opium abuse is frequent and it could be a new health problem in the future. In this regard, evaluation of blood lead level would be important for early diagnosis of lead poisoning in opium addicts. PMID:29416839

  18. Health information systems and pesticide poisoning at Pernambuco.

    Science.gov (United States)

    de Albuquerque, Pedro Costa Cavalcanti; Gurgel, Idê Gomes Dantas; Gurgel, Aline do Monte; Augusto, Lia Giraldo da Silva; de Siqueira, Marília Teixeira

    2015-01-01

    Understanding the epidemiologic profile of a particular disease is key to undertake health actions. To that end, information systems that present quality data help in the decision-making process and demonstrate the impact of the problems. To analyze the contribution of health information systems for the characterization of pesticide poisoning through SINAN, CEATOX and SIM in the State of Pernambuco. In this study, the completeness and consistency of the data were assessed, as well as the epidemiological profile of pesticide poisoning in Pernambuco in the period from 2008 to 2012, based on the following Health Information Systems: Center for Toxicological Assistance of Pernambuco (CEATOX), Notifiable Diseases Information System (SINAN) and Mortality Information System (SIM). The data revealed incompleteness and inconsistencies in information. Regarding the profile, females are more affected in the morbidity profile, and men have a higher mortality rate. Poisoning was more frequent in young adults with low educational level. With regard to the circumstances, most of the cases were suicide attempts, unique acute cases and not related to work. Despite suggesting underreporting, the data showed that persons engaged in agriculture are most commonly affected. The strengthening of these systems is necessary for the generation of consistent information that support health policies for the population groups involved.

  19. Process for growing a film epitaxially upon a MGO surface and structures formed with the process

    Science.gov (United States)

    McKee, Rodney Allen; Walker, Frederick Joseph

    1998-01-01

    A process and structure wherein optical quality perovskites, such as BaTiO.sub.3 or SrTiO.sub.3, are grown upon a single crystal MgO substrate involves the epitaxial build up of alternating planes of TiO.sub.2 and metal oxide wherein the first plane grown upon the MgO substrate is a plane of TiO.sub.2. The layering sequence involved in the film build up reduces problems which would otherwise result from the interfacial electrostatics at the first atomic layers, and these oxides can be stabilized as commensurate thin films at a unit cell thickness or grown with high crystal quality to thicknesses of 0.5-0.7 .mu.m for optical device applications.

  20. Toad poisoning in three dogs: case reports

    Directory of Open Access Journals (Sweden)

    CM Barbosa

    2009-01-01

    Full Text Available Toad poisoning is frequent in dogs, but has been infrequently addressed in published case reports and review articles. Dogs can be poisoned when they bite a toad or otherwise ingest the venom. The venom effects manifest soon after the accident, since the toxin is rapidly absorbed by the mucous membrane of the digestive system. Hospital records of three dogs, diagnosed with toad poisoning, were retrospectively reviewed from January 2005 to July 2007. Poisoned dogs may present only local irritation or systemic signs in the gastrointestinal, cardiac and neurological systems. All three cases presented herein had clinical signs of gastrointestinal alterations including vomiting, sialorrhea and diarrhea. Two dogs developed abnormal cardiac rhythm and two exhibited neurological signs. A poisoned animal requires emergency care and symptomatic therapy with intense monitoring of its clinical parameters. Although there have been reports on the low mortality of dogs poisoned by toads, one animal died even after appropriate therapy. The severity of clinical signs and the risk of death must be considered by the veterinarian.