Surface qualities after chemical-mechanical polishing on thin films

International Nuclear Information System (INIS)

Fu, Wei-En; Lin, Tzeng-Yow; Chen, Meng-Ke; Chen, Chao-Chang A.

2009-01-01

Demands for substrate and film surface planarizations significantly increase as the feature sizes of Integrated Circuit (IC) components continue to shrink. Chemical Mechanical Polishing (CMP), incorporating chemical and mechanical interactions to planarize chemically modified surface layers, has been one of the major manufacturing processes to provide global and local surface planarizations in IC fabrications. Not only is the material removal rate a concern, the qualities of the CMP produced surface are critical as well, such as surface finish, defects and surface stresses. This paper is to examine the CMP produced surface roughness on tungsten or W thin films based on the CMP process conditions. The W thin films with thickness below 1000 nm on silicon wafer were chemical-mechanical polished at different down pressures and platen speeds to produce different surface roughness. The surface roughness measurements were performed by an atomic force microscope (DI D3100). Results show that the quality of surface finish (R a value) is determined by the combined effects of down pressures and platen speeds. An optimal polishing condition is, then, possible for selecting the down pressures and platen speeds.

Response mechanism for surface acoustic wave gas sensors based on surface-adsorption.

Science.gov (United States)

Liu, Jiansheng; Lu, Yanyan

2014-04-16

A theoretical model is established to describe the response mechanism of surface acoustic wave (SAW) gas sensors based on physical adsorption on the detector surface. Wohljent's method is utilized to describe the relationship of sensor output (frequency shift of SAW oscillator) and the mass loaded on the detector surface. The Brunauer-Emmett-Teller (BET) formula and its improved form are introduced to depict the adsorption behavior of gas on the detector surface. By combining the two methods, we obtain a theoretical model for the response mechanism of SAW gas sensors. By using a commercial SAW gas chromatography (GC) analyzer, an experiment is performed to measure the frequency shifts caused by different concentration of dimethyl methylphosphonate (DMMP). The parameters in the model are given by fitting the experimental results and the theoretical curve agrees well with the experimental data.

Conciliating surface superhydrophobicities and mechanical strength of porous silicon films

Science.gov (United States)

Wang, Fuguo; Zhao, Kun; Cheng, Jinchun; Zhang, Junyan

2011-01-01

Hydrophobic surfaces on Mechanical stable macroporous silicon films were prepared by electrochemical etching with subsequent octadecyltrichlorosilane (OTS) modification. The surface morphologies were controlled by current densities and the mechanical properties were adjusted by their corresponding porosities. Contrast with the smooth macroporous silicon films with lower porosities (34.1%) and microporous silicon with higher porosities (97%), the macroporous film with a rough three-dimension (3D) surface and a moderate pore to cross-section area ratio (37.8%, PSi2‧) exhibited both good mechanical strength (Yong' modulus, shear modulus and collapse strength are 64.2, 24.1 and 0.32 GPa, respectively) and surface superhydrophobicity (water contact angle is 158.4 ± 2° and sliding angle is 2.7 ± 1°). This result revealed that the surface hydrophobicities (or the surface roughness) and mechanical strength of porous films could be conciliated by pore to cross-section area ratios control and 3D structures construction. Thus, the superhydrophobic surfaces on mechanical stable porous films could be obtained by 3D structures fabrication on porous film with proper pore to cross-section area ratios.

Mechanical and chemical decontamination of surfaces

International Nuclear Information System (INIS)

Kienhoefer, M.

1982-01-01

Decontamination does not mean more than a special technique of cleaning surfaces by methods well known in the industry. The main difference consists in the facts that more than just the visible dirt is to be removed and that radioactive contamination cannot be seen. Especially, intensive mechanical and chemical carry-off methods are applied to attack the surfaces. In order to minimize damages caused to the surfaces, the decontamination method is to adapt to the material and the required degree of decontamination. The various methods, their advantages and disadvantages are described, and the best known chemical solutions are shown. (orig./RW)

Effects of surface atomistic modification on mechanical properties of gold nanowires

International Nuclear Information System (INIS)

Sun, Xiao-Yu; Xu, Yuanjie; Wang, Gang-Feng; Gu, Yuantong; Feng, Xi-Qiao

2015-01-01

Highlights: • Molecular dynamics simulations of surface modification effect of Au nanowires. • Surface modification can greatly affect the mechanical properties of nanowires. • Core–shell model is used to elucidate the effect of residual surface stress. - Abstract: Modulation of the physical and mechanical properties of nanowires is a challenging issue for their technological applications. In this paper, we investigate the effects of surface modification on the mechanical properties of gold nanowires by performing molecular dynamics simulations. It is found that by modifying a small density of silver atoms to the surface of a gold nanowire, the residual surface stress state can be altered, rendering a great improvement of its plastic yield strength. This finding is in good agreement with experimental measurements. The underlying physical mechanisms are analyzed by a core–shell nanowire model. The results are helpful for the design and optimization of advanced nanomaterial with superior mechanical properties

Mechanical and tribological properties of ion beam-processed surfaces

International Nuclear Information System (INIS)

Kodali, P.

1998-01-01

The intent of this work was to broaden the applications of well-established surface modification techniques and to elucidate the various wear mechanisms that occur in sliding contact of ion-beam processed surfaces. The investigation included characterization and evaluation of coatings and modified surfaces synthesized by three surface engineering methods; namely, beam-line ion implantation, plasma-source ion implantation, and DC magnetron sputtering. Correlation among measured properties such as surface hardness, fracture toughness, and wear behavior was also examined. This dissertation focused on the following areas of research: (1) investigating the mechanical and tribological properties of mixed implantation of carbon and nitrogen into single crystal silicon by beam-line implantation; (2) characterizing the mechanical and tribological properties of diamond-like carbon (DLC) coatings processed by plasma source ion implantation; and (3) developing and evaluating metastable boron-carbon-nitrogen (BCN) compound coatings for mechanical and tribological properties. The surface hardness of a mixed carbon-nitrogen implant sample improved significantly compared to the unimplanted sample. However, the enhancement in the wear factor of this sample was found to be less significant than carbon-implanted samples. The presence of nitrogen might be responsible for the degraded wear behavior since nitrogen-implantation alone resulted in no improvement in the wear factor. DLC coatings have low friction, low wear factor, and high hardness. The fracture toughness of DLC coatings has been estimated for the first time. The wear mechanism in DLC coatings investigated with a ruby slider under a contact stress of 1 GPa was determined to be plastic deformation. The preliminary data on metastable BCN compound coatings indicated high friction, low wear factor, and high hardness

Influence of surface topography in the boiling mechanisms

International Nuclear Information System (INIS)

Moita, A.S.; Teodori, E.; Moreira, A.L.N.

2015-01-01

Highlights: • Pool boiling heat transfer. • Use of micro-textured surfaces to enhance heat transfer. • Importance of the bubble dynamics and of the interaction mechanisms in the overall heat transfer efficiency. • Effect of the micro-textures on bubble dynamics as a way to enhance pool boiling heat transfer. - Abstract: The present paper addresses the qualitative and quantitative analysis of the pool boiling heat transfer over micro-structured surfaces. The surfaces are made from silicon chips, in the context of pool boiling heat transfer enhancement of immersion liquid cooling schemes for electronic components. The first part of the analysis deals with the effect of the liquid properties. Then the effect of surface micro-structuring is discussed, covering different configurations, from cavities to pillars being the latter used to infer on the potential profit of a fin-like configuration. The use of rough surfaces to enhance pool boiling mainly stands on the arguments that the surface roughness will increase the liquid–solid contact area, thus enhancing the convection heat transfer coefficient and will promote the generation of nucleation sites. However, one should not disregard bubble dynamics. Indeed, the results show a strong effect of bubble dynamics and particularly of the interaction mechanisms in the overall cooling performance of the pair liquid–surface. The inaccurate control of these mechanisms leads to the formation of large bubbles and strong vertical and horizontal coalescence effects promote the very fast formation of a vapor blanket, which causes a steep decrease of the heat transfer coefficient. This effect can be strong enough to prevail over the benefit of increasing the contact area by roughening the surface. For the micro-patterns used in the present work, the results evidence that one can reasonably determine guiding pattern characteristics to evaluate the intensity of the interaction mechanisms and take out the most of the

Engaging students as partners in developing online learning and feedback activities for first-year fluid mechanics

Science.gov (United States)

Brown, Alan

2018-01-01

Much learning takes place outside of formal class settings, yet students starting in higher education are not always well equipped with independent learning skills, appropriate self-knowledge or the required levels of intrinsic motivation This project used students as partners to develop resources that could be used by first-year undergraduates in fluid mechanics, using activities and receiving feedback through the virtual learning environment (VLE), in order to build these three attributes of independent learners. While there were significant benefits to the students who developed the resources, the target students saw much lower benefits as a result of poorer than expected engagement. The challenge this research presents is to develop activities that maximise engagement in large classes, as well as develop appropriate independent learning skills.

Surface Damage Mechanism of Monocrystalline Si Under Mechanical Loading

Science.gov (United States)

Zhao, Qingliang; Zhang, Quanli; To, Suet; Guo, Bing

2017-03-01

Single-point diamond scratching and nanoindentation on monocrystalline silicon wafer were performed to investigate the surface damage mechanism of Si under the contact loading. The results showed that three typical stages of material removal appeared during dynamic scratching, and a chemical reaction of Si with the diamond indenter and oxygen occurred under the high temperature. In addition, the Raman spectra of the various points in the scratching groove indicated that the Si-I to β-Sn structure (Si-II) and the following β-Sn structure (Si-II) to amorphous Si transformation appeared under the rapid loading/unloading condition of the diamond grit, and the volume change induced by the phase transformation resulted in a critical depth (ductile-brittle transition) of cut (˜60 nm ± 15 nm) much lower than the theoretical calculated results (˜387 nm). Moreover, it also led to abnormal load-displacement curves in the nanoindentation tests, resulting in the appearance of elbow and pop-out effects (˜270 nm at 20 s, 50 mN), which were highly dependent on the loading/unloading conditions. In summary, phase transformation of Si promoted surface deformation and fracture under both static and dynamic mechanical loading.

Multiresolution molecular mechanics: Surface effects in nanoscale materials

Energy Technology Data Exchange (ETDEWEB)

Yang, Qingcheng, E-mail: qiy9@pitt.edu; To, Albert C., E-mail: albertto@pitt.edu

2017-05-01

Surface effects have been observed to contribute significantly to the mechanical response of nanoscale structures. The newly proposed energy-based coarse-grained atomistic method Multiresolution Molecular Mechanics (MMM) (Yang, To (2015), ) is applied to capture surface effect for nanosized structures by designing a surface summation rule SR{sup S} within the framework of MMM. Combined with previously proposed bulk summation rule SR{sup B}, the MMM summation rule SR{sup MMM} is completed. SR{sup S} and SR{sup B} are consistently formed within SR{sup MMM} for general finite element shape functions. Analogous to quadrature rules in finite element method (FEM), the key idea to the good performance of SR{sup MMM} lies in that the order or distribution of energy for coarse-grained atomistic model is mathematically derived such that the number, position and weight of quadrature-type (sampling) atoms can be determined. Mathematically, the derived energy distribution of surface area is different from that of bulk region. Physically, the difference is due to the fact that surface atoms lack neighboring bonding. As such, SR{sup S} and SR{sup B} are employed for surface and bulk domains, respectively. Two- and three-dimensional numerical examples using the respective 4-node bilinear quadrilateral, 8-node quadratic quadrilateral and 8-node hexahedral meshes are employed to verify and validate the proposed approach. It is shown that MMM with SR{sup MMM} accurately captures corner, edge and surface effects with less 0.3% degrees of freedom of the original atomistic system, compared against full atomistic simulation. The effectiveness of SR{sup MMM} with respect to high order element is also demonstrated by employing the 8-node quadratic quadrilateral to solve a beam bending problem considering surface effect. In addition, the introduced sampling error with SR{sup MMM} that is analogous to numerical integration error with quadrature rule in FEM is very small. - Highlights: �

Condensation Enhancement by Surface Porosity: Three-Stage Mechanism.

Science.gov (United States)

Yarom, Michal; Marmur, Abraham

2015-08-18

Surface defects, such as pores, cracks, and scratches, are naturally occurring and commonly found on solid surfaces. However, the mechanism by which such imperfections promote condensation has not been fully explored. In the current paper we thermodynamically analyze the ability of surface porosity to enhance condensation on a hydrophilic solid. We show that the presence of a surface-embedded pore brings about three distinct stages of condensation. The first is capillary condensation inside the pore until it is full. This provides an ideal hydrophilic surface for continuing the condensation. As a result, spontaneous condensation and wetting can be achieved at lower vapor pressure than on a smooth surface.

Surface effects on the mechanical properties of nanoporous materials

International Nuclear Information System (INIS)

Lu Zixing; Zhang Cungang; Liu Qiang; Yang Zhenyu

2011-01-01

In this paper, surface effects on the mechanical behaviour of nanoporous materials are investigated using the theory of surface elasticity and Timoshenko beam theory based on the tetrakaidecahedron (or Kelvin) open-cell foam model. Meanwhile, the influence of surface elasticity and residual surface stress on the mechanical properties of nanoporous materials is discussed. In addition, the results derived from the theory of Euler-Bernoulli beam model are also provided for comparison. Theoretical results show that the effective Young's modulus of the nanoporous materials increases as the diameter of the strut decreases, but in contrast Poisson's ratio and the brittle collapse strength decrease with the diameter of the strut. The contribution of shear deformation to surface effects on elastic properties is more significant, while the surface effects on brittle collapse strength are not sensitive to shear deformation, and it can even be neglected. As the strut size increases, the present results can be reduced to the cases without considering surface effects, which verifies the efficiency of the present model to a certain extent.

Mechanisms and energetics of surface atomic processes

International Nuclear Information System (INIS)

Tsong, T.T.

1991-01-01

The energies involved in various surface atomic processes such as surface diffusion, the binding of small atomic clusters on the surface, the interaction between two adsorbed atoms, the dissociation of an atom from a small cluster or from a surface layer, the binding of kink size atoms or atoms at different adsorption sites to the surface etc., can be derived from an analysis of atomically resolved field ion microscope images and a kinetic energy measurement of low temperature field desorbed ions using the time-of-flight atom-probe field ion microscope. These energies can be used to compare with theories and to understand the transport of atoms on the surface in atomic reconstructions, epitaxial growth of surface layers and crystal growth, adsorption layer superstructure formation, and also why an atomic ordering or atomic reconstruction at the surface is energetically favored. Mechanisms of some of the surface atomic processes are also clarified from these quantitative, atomic resolution studies. In this paper work in this area is bris briefly reviewed

Nutrients and Hydrology Indicate the Driving Mechanisms of Peatland Surface Patterning

NARCIS (Netherlands)

Eppinga, M.B.; Ruiter, de P.C.; Wassen, M.J.; Rietkerk, M.

2009-01-01

Peatland surface patterning motivates studies that identify underlying structuring mechanisms. Theoretical studies so far suggest that different mechanisms may drive similar types of patterning. The long time span associated with peatland surface pattern formation, however, limits possibilities for

Exploring physics students' engagement with online instructional videos in an introductory mechanics course

Science.gov (United States)

Lin, Shih-Yin; Aiken, John M.; Seaton, Daniel T.; Douglas, Scott S.; Greco, Edwin F.; Thoms, Brian D.; Schatz, Michael F.

2017-12-01

The advent of new educational technologies has stimulated interest in using online videos to deliver content in university courses. We examined student engagement with 78 online videos that we created and were incorporated into a one-semester flipped introductory mechanics course at the Georgia Institute of Technology. We found that students were more engaged with videos that supported laboratory activities than with videos that presented lecture content. In particular, the percentage of students accessing laboratory videos was consistently greater than 80% throughout the semester. On the other hand, the percentage of students accessing lecture videos dropped to less than 40% by the end of the term. Moreover, the fraction of students accessing the entirety of a video decreases when videos become longer in length, and this trend is more prominent for the lecture videos than the laboratory videos. The results suggest that students may access videos based on perceived value: students appear to consider the laboratory videos as essential for successfully completing the laboratories while they appear to consider the lecture videos as something more akin to supplemental material. In this study, we also found that there was little correlation between student engagement with the videos and their incoming background. There was also little correlation found between student engagement with the videos and their performance in the course. An examination of the in-video content suggests that students engaged more with concrete information that is explicitly required for assignment completion (e.g., actions required to complete laboratory work, or formulas or mathematical expressions needed to solve particular problems) and less with content that is considered more conceptual in nature. It was also found that students' in-video accesses usually increased toward the embedded interaction points. However, students did not necessarily access the follow-up discussion of these

Mechanism of supercooled droplet freezing on surfaces.

Science.gov (United States)

Jung, Stefan; Tiwari, Manish K; Doan, N Vuong; Poulikakos, Dimos

2012-01-10

Understanding ice formation from supercooled water on surfaces is a problem of fundamental importance and general utility. Superhydrophobic surfaces promise to have remarkable 'icephobicity' and low ice adhesion. Here we show that their icephobicity can be rendered ineffective by simple changes in environmental conditions. Through experiments, nucleation theory and heat transfer physics, we establish that humidity and/or the flow of a surrounding gas can fundamentally switch the ice crystallization mechanism, drastically affecting surface icephobicity. Evaporative cooling of the supercooled liquid can engender ice crystallization by homogeneous nucleation at the droplet-free surface as opposed to the expected heterogeneous nucleation at the substrate. The related interplay between droplet roll-off and rapid crystallization is also studied. Overall, we bring a novel perspective to icing and icephobicity, unveiling the strong influence of environmental conditions in addition to the accepted effects of the surface conditions and hydrophobicity.

Mechanical response of wall-patterned GaAs surface

International Nuclear Information System (INIS)

Le Bourhis, E.; Patriarche, G.

2005-01-01

Wall-patterned GaAs surfaces have been elaborated by photolithography and dry etching. Different surfaces were produced in order to change the aspect ratio of the walls formed at the substrate surface. The mechanical behaviour of individual walls was investigated by nanoindentation and the responses were compared to that of a standard bulk reference (flat surface). Deviation from the bulk response is detected in a load range of 1-25 mN depending on the aspect ratio of the walls. A central plastic zone criterion is proposed in view of transmission electron microscopy images of indented walls and allows the prediction of the response deviation of a given wall if its width is known. The mechanical response of the different types of walls is further investigated in terms of stiffness, total penetration of indenter and apparent hardness, and is scanned in relation to the proximity of a wall side. Overall results show that contact stiffness remains almost unaffected by aspect ratio, while penetration drastically increases because of the free sides of the wall as compared to a flat surface (bulk substrate). The application of substrate patterning for optoelectronic devices is discussed in the perspective of eliminating residual dislocations appearing in mismatched structures

Micropatterned Azopolymer Surfaces Modulate Cell Mechanics and Cytoskeleton Structure.

Science.gov (United States)

Rianna, Carmela; Ventre, Maurizio; Cavalli, Silvia; Radmacher, Manfred; Netti, Paolo A

2015-09-30

Physical and chemical characteristics of materials are important regulators of cell behavior. In particular, cell elasticity is a fundamental parameter that reflects the state of a cell. Surface topography finely modulates cell fate and function via adhesion mediated signaling and cytoskeleton generated forces. However, how topographies alter cell mechanics is still unclear. In this work we have analyzed the mechanical properties of peripheral and nuclear regions of NIH-3T3 cells on azopolymer substrates with different topographic patterns. Micrometer scale patterns in the form of parallel ridges or square lattices of surface elevations were encoded on light responsive azopolymer films by means of contactless optical methods. Cell mechanics was investigated by atomic force microscopy (AFM). Cells and consequently the cell cytoskeleton were oriented along the linear patterns affecting cytoskeletal structures, e.g., formation of actin stress fibers. Our data demonstrate that topographic substrate patterns are recognized by cells and mechanical information is transferred by the cytoskeleton. Furthermore, cytoskeleton generated forces deform the nucleus, changing its morphology that appears to be related to different mechanical properties in the nuclear region.

Novel exchange mechanisms in the surface diffusion of oxides

International Nuclear Information System (INIS)

Harris, Duncan J; Lavrentiev, Mikhail Yu; Harding, John H; Allan, Neil L; Purton, John A

2004-01-01

We use temperature-accelerated dynamics to show the importance of exchange mechanisms in surface diffusion and growth of simple oxides. Such mechanisms can dominate transport processes both on terraces and steps for both homoepitaxial and heteroepitaxial growth. We suggest that the mixing inevitable when an exchange mechanism is present must be considered when attempts are made to grow sharp interfaces in oxide nanostructures. (letter to the editor)

Surface Spectroscopic Signatures of Mechanical Deformation in HDPE.

Science.gov (United States)

Averett, Shawn C; Stanley, Steven K; Hanson, Joshua J; Smith, Stacey J; Patterson, James E

2018-01-01

High-density polyethylene (HDPE) has been extensively studied, both as a model for semi-crystalline polymers and because of its own industrial utility. During cold drawing, crystalline regions of HDPE are known to break up and align with the direction of tensile load. Structural changes due to deformation should also manifest at the surface of the polymer, but until now, a detailed molecular understanding of how the surface responds to mechanical deformation has been lacking. This work establishes a precedent for using vibrational sum-frequency generation (VSFG) spectroscopy to investigate changes in the molecular-level structure of the surface of HDPE after cold drawing. X-ray diffraction (XRD) was used to confirm that the observed surface behavior corresponds to the expected bulk response. Before tensile loading, the VSFG spectra indicate that there is significant variability in the surface structure and tilt of the methylene groups away from the surface normal. After deformation, the VSFG spectroscopic signatures are notably different. These changes suggest that hydrocarbon chains at the surface of visibly necked HDPE are aligned with the direction of loading, while the associated methylene groups are oriented with the local C 2 v symmetry axis roughly parallel to the surface normal. Small amounts of unaltered material are also found at the surface of necked HDPE, with the relative amount of unaltered material decreasing as the amount of deformation increases. Aspects of the nonresonant SFG response in the transition zone between necked and undeformed polymer provide additional insight into the deformation process and may provide the first indication of mechanical deformation. Nonlinear surface spectroscopy can thus be used as a noninvasive and nondestructive tool to probe the stress history of a HPDE sample in situations where X-ray techniques are not available or not applicable. Vibrational sum-frequency generation thus has great potential as a platform for

Topological Fluid Mechanics with Applications to Free Surfaces and Axisymmetric Flows

DEFF Research Database (Denmark)

Brøns, Morten

1996-01-01

Topological fluid mechanics is the study of qualitative features of fluid patterns. We discuss applications to the flow beneath a stagnant surface film, and to patterns in axisymmetric flow.......Topological fluid mechanics is the study of qualitative features of fluid patterns. We discuss applications to the flow beneath a stagnant surface film, and to patterns in axisymmetric flow....

Influence of Workpiece Surface Topography on the Mechanisms of Liquid Lubrication in Strip Drawing

DEFF Research Database (Denmark)

Shimizu, I; Andreasen, Jan Lasson; Bech, Jakob Ilsted

2001-01-01

The workpiece surface topography is an important factor controlling the mechanisms of lubrication in metal forming processes. In the present work, the microscopic lubrication mechanisms induced by lubricant trapped in pockets of the surface in strip drawing are studied. The experiments are perfor......The workpiece surface topography is an important factor controlling the mechanisms of lubrication in metal forming processes. In the present work, the microscopic lubrication mechanisms induced by lubricant trapped in pockets of the surface in strip drawing are studied. The experiments...

Near surface mechanical properties of optical single crystals and surface response to deterministic microgrinding

Science.gov (United States)

Randi, Joseph A., III

2005-12-01

This thesis makes use of microindentation, nanoindentation and nanoscratching methods to better understand the mechanical properties of single crystalline silicon, calcium fluoride, and magnesium fluoride. These properties are measured and are used to predict the material's response to material removal, specifically by grinding and polishing, which is a combination of elastic, plastic and fracture processes. The hardness anisotropy during Knoop microindentation, hardness from nanoindentation, and scratch morphology from nanoscratching are reported. This information is related to the surface microroughness from grinding. We show that mechanical property relationships that predict the surface roughness from lapping and deterministic microgrinding of optical glasses are applicable to single crystals. We show the range of hardness from some of the more common crystallographic faces. Magnesium fluoride, having a tetragonal structure, has 2-fold hardness anisotropy. Nanoindentation, as expected provides higher hardness than microindentation, but anisotropy is not observed. Nanoscratching provides the scratch profile during loading, after the load has been removed, and the coefficient of friction during the loading. Ductile and brittle mode scratching is present with brittle mode cracking being orientation specific. Subsurface damage (SSD) measurements are made using a novel process known as the MRF technique. Magnetorheological finishing is used to polish spots into the ground surface where SSD can be viewed. SSD is measured using an optical microscope and knowledge of the spot profile. This technique is calibrated with a previous technique and implemented to accurately measure SSD in single crystals. The data collected are compared to the surface microroughness of the ground surface, resulting in an upper bound relationship. The results indicate that SSD is always less than 1.4 times the peak-to-valley surface microroughness for single crystals regardless of the

Mechanical torques generated by optically pumped atomic spin relaxation at surfaces

International Nuclear Information System (INIS)

Herman, R.M.

1982-01-01

It is argued that a valuable method of observing certain types of surface-atom interactions may lie in mechanical torques generated through the spin-orbit relaxation of valence electronic spins of optically pumped atoms at surfaces. The unusual feature of this phenomenon is that the less probable spin-orbit relaxation becomes highly visible as compared with the much more rapid paramagnetic relaxation, because of an enhancement, typically by as much as a factor 10 9 , in the torques delivered to mechanical structures, by virtue of a very large effective moment arm. Spin-orbit relaxation operates through an exchange of translational momentum which, in turn, can be identified with the delivery of a gigantic angular momentum (in units of h) relative to a distant axis about which mechanical motion is referred. The spin-orbit relaxation strongly depends upon the atomic number of the surface atoms and the strength of interaction with the optically pumped atoms. Being dominated by high-atomic-number surface atoms, spin-orbit relaxation rates may not be too strongly influenced by minor surface contamination of lighter-weight optically active atoms

Mechanical torques generated by optically pumped atomic spin relaxation at surfaces

Science.gov (United States)

Herman, R. M.

1982-03-01

It is argued that a valuable method of observing certain types of surface-atom interactions may lie in mechanical torques generated through the spin-orbit relaxation of valence electronic spins of optically pumped atoms at surfaces. The unusual feature of this phenomenon is that the less probable spin-orbit relaxation becomes highly visible as compared with the much more rapid paramagnetic relaxation, because of an enhancement, typically by as much as a factor 109, in the torques delivered to mechanical structures, by virtue of a very large effective moment arm. Spin-orbit relaxation operates through an exchange of translational momentum which, in turn, can be identified with the delivery of a gigantic angular momentum (in units of ℏ) relative to a distant axis about which mechanical motion is referred. The spin-orbit relaxation strongly depends upon the atomic number of the surface atoms and the strength of interaction with the optically pumped atoms. Being dominated by high-atomic-number surface atoms, spin-orbit-relaxation rates may not be too strongly influenced by minor surface contamination of lighter-weight optically active atoms.

Generation Mechanism of Work Hardened Surface Layer in Metal Cutting

Science.gov (United States)

Hikiji, Rikio; Kondo, Eiji; Kawagoishi, Norio; Arai, Minoru

Finish machining used to be carried out in grinding, but it is being replaced by cutting with very small undeformed chip thickness. In ultra precision process, the effects of the cutting conditions and the complicated factors on the machined surface integrity are the serious problems. In this research, work hardened surface layer was dealt with as an evaluation of the machined surface integrity and the effect of the mechanical factors on work hardening was investigated experimentally in orthogonal cutting. As a result, it was found that work hardened surface layer was affected not only by the shear angle varied under the cutting conditions and the thrust force of cutting resistance, but also by the thrust force acting point, the coefficient of the thrust force and the compressive stress equivalent to the bulk hardness. Furthermore, these mechanical factors acting on the depth of the work hardened surface layer were investigated with the calculation model.

Mechanical stability of surface architecture--consequences for superhydrophobicity.

Science.gov (United States)

Dyett, Brendan P; Wu, Alex H; Lamb, Robert N

2014-11-12

Wet chemistry methods such as sol-gel provide a facile means of preparing coatings with controlled surface chemistry and architecture. The manipulation of colloidal "building blocks," film constituents, and reaction conditions makes it a promising method for simple, scalable, and routine production of superhydrophobic coatings. Despite all of this, the practical application of superhydrophobic coatings remains limited by low mechanical durability. The translation of chemistry to mechanical strength within superhydrophobic films is severely hindered by the requisite physical structure. More specifically, porosity and the surface architecture of roughness in sol-gel-derived films contribute significantly to poor mechanical properties. These physical effects emphasize that collective structure and chemistry-based strategies are required. This challenge is not unique to superhydrophobics, and there are many principles that can be drawn upon to greatly improve performance. The delicate interplay between chemistry and physical structure has been highlighted through theory and characterization of porous and rough interfaces within and outside the framework of superhydrophobics. Insights can further be drawn from biology. Nature's capacity for self-repair remains extremely challenging to mimic in materials. However, nature does demonstrate strategies for structuring nano- and microbuilding blocks to achieve generally mutually exclusive properties. Difficulties with characterization and example mechanical characterization methods have also been emphasized.

On the mechanics of thin films and growing surfaces

KAUST Repository

Holland, M. A.

2013-05-24

Many living structures are coated by thin films, which have distinct mechanical properties from the bulk. In particular, these thin layers may grow faster or slower than the inner core. Differential growth creates a balanced interplay between tension and compression and plays a critical role in enhancing structural rigidity. Typical examples with a compressive outer surface and a tensile inner core are the petioles of celery, caladium, or rhubarb. While plant physiologists have studied the impact of tissue tension on plant rigidity for more than a century, the fundamental theory of growing surfaces remains poorly understood. Here, we establish a theoretical and computational framework for continua with growing surfaces and demonstrate its application to classical phenomena in plant growth. To allow the surface to grow independently of the bulk, we equip it with its own potential energy and its own surface stress. We derive the governing equations for growing surfaces of zero thickness and obtain their spatial discretization using the finite-element method. To illustrate the features of our new surface growth model we simulate the effects of growth-induced longitudinal tissue tension in a stalk of rhubarb. Our results demonstrate that different growth rates create a mechanical environment of axial tissue tension and residual stress, which can be released by peeling off the outer layer. Our novel framework for continua with growing surfaces has immediate biomedical applications beyond these classical model problems in botany: it can be easily extended to model and predict surface growth in asthma, gastritis, obstructive sleep apnoea, brain development, and tumor invasion. Beyond biology and medicine, surface growth models are valuable tools for material scientists when designing functionalized surfaces with distinct user-defined properties. © The Author(s) 2013.

Surface mechanics design by cavitation peening

OpenAIRE

Hitoshi Soyama

2015-01-01

Although impacts at cavitation bubble collapses cause severe damage in hydraulic machineries, the cavitation impacts can be utilised for surface mechanics design such as introduction of compressive residual stress and/or improvement of fatigue strength. The peening method using the cavitation impacts was called as cavitation peening. In order to reveal the peening intensity of hydrodynamic cavitation and laser cavitation, the arc height of Almen strip and duralumin plate were measured. In the...

Neutralization mechanisms in He+-Al surface collisions

International Nuclear Information System (INIS)

Bajales, N.; Ferron, J.; Goldberg, E.C.

2007-01-01

From a quantum mechanical calculation where the populations of He ground and first excited states are properly taken into account, we can identify for the first time the neutralization to the He first excited state as an operative mechanism in He + -Al surface collisions. This identification allows us to understand the presence of high energy electrons in the ion induced electron emission spectra, through the inclusion of Auger deexcitation as an electron emission source, as well as to suggest a possible cause for the disagreement still found between theory and experiments in low energy ion scattering (LEIS) for this system

Nanocrystalline-grained tungsten prepared by surface mechanical attrition treatment: Microstructure and mechanical properties

International Nuclear Information System (INIS)

Guo, Hong-Yan; Xia, Min; Wu, Zheng-Tao; Chan, Lap-Chung; Dai, Yong; Wang, Kun; Yan, Qing-Zhi; He, Man-Chao; Ge, Chang-Chun; Lu, Jian

2016-01-01

A nanostructured surface layer was fabricated on commercial pure tungsten using the method of surface mechanical attrition treatment (SMAT). The microstructure evolution of the surface layer was characterized by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and its formation mechanism was discussed as well. Both refinement and elongation of the brittle W grains were confirmed. The elongated SMATed W was heavily strained, the maximum value of the strain at the grain boundaries reaches as high as 3–5%. Dislocation density in the SMATed W nanograins was found to be 5 × 10 12  cm −2 . The formation of the nanograins in the top surface layer of the W was ascribed to the extremely high strain and strain rate, as well as the multidirectional repetitive loading. Bending strength of commercial W could be improved from 825 MPa to 1850 MPa by SMAT process. Microhardness results indicated the strain range in SMATed W can reach up to 220 μm beneath the top surface. The notched Charpy testing results demonstrated that SMATed W possess higher ductility than that of commercial W. The top surface of the W plates with and without SMATe processing possesses residual compressive stress of about −881 MPa and −234 MPa in y direction, and −872 MPa and −879 MPa in x direction respectively. The improvement of toughness (DBTT shift) of SMATed W may be the synergistic effect of residual compressive stress, dislocation density improvement and microstructure refinement induced by SMAT processing. SMAT processing could be a complementary method to further decrease the DBTT value of tungsten based materials.

Nanocrystalline-grained tungsten prepared by surface mechanical attrition treatment: Microstructure and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Guo, Hong-Yan [State Key Laboratory for GeoMechanics and Deep Underground Engineering, China University of Mining and Technology, Beijing 100083 (China); Institute of Nuclear Materials, University of Science & Technology Beijing, Beijing 100083 (China); Department of Mechanical and Biomedical Engineering, City University of Hong Kong, Tae Chee Avenue Kowloon, Hong Kong 999077 (China); Xia, Min, E-mail: xmdsg@ustb.edu.cn [Institute of Nuclear Materials, University of Science & Technology Beijing, Beijing 100083 (China); Wu, Zheng-Tao [College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Chan, Lap-Chung [Department of Mechanical and Biomedical Engineering, City University of Hong Kong, Tae Chee Avenue Kowloon, Hong Kong 999077 (China); Dai, Yong; Wang, Kun [Laboratory for Nuclear Materials, Paul Scherrer Institut, 5323 Villigen PSI (Switzerland); Yan, Qing-Zhi [Institute of Nuclear Materials, University of Science & Technology Beijing, Beijing 100083 (China); He, Man-Chao [State Key Laboratory for GeoMechanics and Deep Underground Engineering, China University of Mining and Technology, Beijing 100083 (China); Ge, Chang-Chun, E-mail: ccge@mater.ustb.edu.cn [Institute of Nuclear Materials, University of Science & Technology Beijing, Beijing 100083 (China); Lu, Jian, E-mail: jianlu@cityu.edu.hk [Department of Mechanical and Biomedical Engineering, City University of Hong Kong, Tae Chee Avenue Kowloon, Hong Kong 999077 (China)

2016-11-15

A nanostructured surface layer was fabricated on commercial pure tungsten using the method of surface mechanical attrition treatment (SMAT). The microstructure evolution of the surface layer was characterized by using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and its formation mechanism was discussed as well. Both refinement and elongation of the brittle W grains were confirmed. The elongated SMATed W was heavily strained, the maximum value of the strain at the grain boundaries reaches as high as 3–5%. Dislocation density in the SMATed W nanograins was found to be 5 × 10{sup 12} cm{sup −2}. The formation of the nanograins in the top surface layer of the W was ascribed to the extremely high strain and strain rate, as well as the multidirectional repetitive loading. Bending strength of commercial W could be improved from 825 MPa to 1850 MPa by SMAT process. Microhardness results indicated the strain range in SMATed W can reach up to 220 μm beneath the top surface. The notched Charpy testing results demonstrated that SMATed W possess higher ductility than that of commercial W. The top surface of the W plates with and without SMATe processing possesses residual compressive stress of about −881 MPa and −234 MPa in y direction, and −872 MPa and −879 MPa in x direction respectively. The improvement of toughness (DBTT shift) of SMATed W may be the synergistic effect of residual compressive stress, dislocation density improvement and microstructure refinement induced by SMAT processing. SMAT processing could be a complementary method to further decrease the DBTT value of tungsten based materials.

Surface-structure dependence of healing radiation-damage mechanism in nanoporous tungsten

Science.gov (United States)

Duan, Guohua; Li, Xiangyan; Sun, Jingjing; Hao, Congyu; Xu, Yichun; Zhang, Yange; Liu, Wei; Liu, C. S.

2018-01-01

Under nuclear fusion environments, displacement damage in tungsten (W) is usually caused by neutrons irradiation through producing large quantities of vacancies (Vs) and self-interstitial atoms (SIAs). These defects not only affect the mechanical properties of W, but also act as the trap sites for implanted hydrogen isotopes and helium. Nano-porous (NP) W with a high fraction of free surfaces has been developed to mitigate the radiation damage. However, the mechanism of the surface reducing defects accumulation is not well understood. By using multi-scale simulation methods, we investigated the interaction of the SIA and V with different surfaces on across length and time scales. We found that, at a typical operation temperature of 1000 K, surface (1 1 0) preferentially heals radiation damage of W compared with surface (1 0 0) and boundary (3 1 0). On surface (1 1 0), the diffusion barrier for the SIA is only 0.68 eV. The annihilation of the SIA-V happens via the coupled motion of the V segregation towards the surface from the bulk and the two-dimensional diffusion of the SIA on the surface. Such mechanism makes the surface (1 1 0) owe better healing capability. On surface (1 0 0), the diffusion energy barrier for the SIA is 2.48 eV, higher than the diffusion energy barrier of the V in bulk. The annihilation of the SIA-V occurs via the V segregation and recombination. The SIA was found to migrate one-dimensionally along a boundary (3 1 0) with a barrier of 0.21 eV, leading to a lower healing efficiency in the boundary. This study suggested that the on-surface process plays an important role in healing radiation damage of NP W in addition to surface-enhanced diffusion and annihilation near the surface. A certain surface structure renders nano-structured W more radiation-tolerant.

Photoelectrochemical etching of gallium nitride surface by complexation dissolution mechanism

Energy Technology Data Exchange (ETDEWEB)

Zhang, Miao-Rong [Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, 215123 Suzhou (China); University of Chinese Academy of Sciences, 100049 Beijing (China); Hou, Fei; Wang, Zu-Gang; Zhang, Shao-Hui [Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, 215123 Suzhou (China); Changchun University of Science and Technology, 130022 Changchun (China); Pan, Ge-Bo, E-mail: gbpan2008@sinano.ac.cn [Suzhou Institute of Nano-Tech and Nano-Bionics, Chinese Academy of Sciences, 215123 Suzhou (China)

2017-07-15

Graphical abstract: GaN surface was etched by 0.3 M EDTA-2Na. The proposed complexation dissolution mechanism can be applicable to almost all neutral etchants under the prerequisite of strong light and electric field. - Highlights: • GaN surface was etched by EDTA-2Na. • GaN may be dissolved into EDTA-2Na by forming Ga–EDTA complex. • We propose the complexation dissolution mechanism for the first time. - Abstract: Gallium nitride (GaN) surface was etched by 0.3 M ethylenediamine tetraacetic acid disodium (EDTA-2Na) via photoelectrochemical etching technique. SEM images reveal the etched GaN surface becomes rough and irregular. The pore density is up to 1.9 × 10{sup 9} per square centimeter after simple acid post-treatment. The difference of XPS spectra of Ga 3d, N 1s and O 1s between the non-etched and freshly etched GaN surfaces can be attributed to the formation of Ga–EDTA complex at the etching interface between GaN and EDTA-2Na. The proposed complexation dissolution mechanism can be broadly applicable to almost all neutral etchants under the prerequisite of strong light and electric field. From the point of view of environment, safety and energy, EDTA-2Na has obvious advantages over conventionally corrosive etchants. Moreover, as the further and deeper study of such nearly neutral etchants, GaN etching technology has better application prospect in photoelectric micro-device fabrication.

Reaction mechanisms for on-surface synthesis of covalent nanostructures

International Nuclear Information System (INIS)

Björk, J

2016-01-01

In recent years, on-surface synthesis has become an increasingly popular strategy to form covalent nanostructures. The approach has great prospects for facilitating the manufacture of a range of fascinating materials with atomic precision. However, the on-surface reactions are enigmatic to control, currently restricting its bright perspectives and there is a great need to explore how the reactions are governed. The objective of this topical review is to summarize theoretical work that has focused on comprehending on-surface synthesis protocols through studies of reaction mechanisms. (topical review)

Continuum damage mechanics method for fatigue growth of surface cracks

International Nuclear Information System (INIS)

Feng Xiqiao; He Shuyan

1997-01-01

With the background of leak-before-break (LBB) analysis of pressurized vessels and pipes in nuclear plants, the fatigue growth problem of either circumferential or longitudinal semi-elliptical surface cracks subjected to cyclic loading is studied by using a continuum damage mechanics method. The fatigue damage is described by a scalar damage variable. From the damage evolution equation at the crack tip, a crack growth equation similar to famous Paris' formula is derived, which shows the physical meaning of Paris' formula. Thereby, a continuum damage mechanics approach is developed to analyze the configuration evolution of surface cracks during fatigue growth

Tuning Acoustic Wave Properties by Mechanical Resonators on a Surface

DEFF Research Database (Denmark)

Dühring, Maria Bayard; Laude, Vincent; Khelif, Abdelkrim

Vibrations generated by high aspects ratio electrodes are studied by the finite element method. It is found that the modes are combined of a surface wave and vibration in the electrodes. For increasing aspect ratio most of the mechanical energy is confined to the electrodes which act as mechanical...

Mechanism of glucose electrochemical oxidation on gold surface

KAUST Repository

Pasta, Mauro; La Mantia, Fabio; Cui, Yi

2010-01-01

The complex oxidation of glucose at the surface of gold electrodes was studied in detail in different conditions of pH, buffer and halide concentration. As observed in previous studies, an oxidative current peak occurs during the cathodic sweep showing a highly linear dependence on glucose concentration, when other electrolyte conditions are unchanged. The effect of the different conditions on the intensity of this peak has stressed the limitations of the previously proposed mechanisms. A mechanism able to explain the presence of this oxidative peak was proposed. The mechanism takes into account ion-sorption and electrochemical adsorption of OH-, buffer species (K2HPO4/KH2PO4) and halides. © 2010 Elsevier Ltd. All rights reserved.

Mechanism of glucose electrochemical oxidation on gold surface

KAUST Repository

Pasta, Mauro

2010-08-01

The complex oxidation of glucose at the surface of gold electrodes was studied in detail in different conditions of pH, buffer and halide concentration. As observed in previous studies, an oxidative current peak occurs during the cathodic sweep showing a highly linear dependence on glucose concentration, when other electrolyte conditions are unchanged. The effect of the different conditions on the intensity of this peak has stressed the limitations of the previously proposed mechanisms. A mechanism able to explain the presence of this oxidative peak was proposed. The mechanism takes into account ion-sorption and electrochemical adsorption of OH-, buffer species (K2HPO4/KH2PO4) and halides. © 2010 Elsevier Ltd. All rights reserved.

Surface effects in solid mechanics models, simulations and applications

CERN Document Server

Altenbach, Holm

2013-01-01

This book reviews current understanding, and future trends, of surface effects in solid mechanics. Covers elasticity, plasticity and viscoelasticity, modeling based on continuum theories and molecular modeling and applications of different modeling approaches.

Negative feedback mechanism for the long-term stabilization of earth's surface temperature

International Nuclear Information System (INIS)

Walker, J.C.G.; Hays, P.B.; Kasting, J.F.

1981-01-01

We suggest that the partial pressure of carbon dioxide in the atmosphere is buffered, over geological time scales, by a negative feedback mechanism in which the rate of weathering of silicate minerals (followed by deposition of carbonate minerals) depends on surface temperature, and surface temperature, in turn, depends on carbon dioxide partial pressure through the green effect. Although the quantitative details of this mechanism are speculative, it appears able partially to stabilize earth's surface temperature against the steady increase of solar luminosity believed to have occured since the origin of the solar system

Exploring Engaging Gamification Mechanics in Massive Online Open Courses

Science.gov (United States)

Chang, Jen-Wei; Wei, Hung-Yu

2016-01-01

Massive open online courses (MOOCs) have developed rapidly and become tremendously popular because of their plentiful gamification designs, such as reputation points, rewards, and goal setting. Although previous studies have mentioned a broad range of gamification designs that might influence MOOC learner engagement, most gamified MOOCs fail to…

Adsorption mechanism of BMP-7 on hydroxyapatite (001) surfaces

International Nuclear Information System (INIS)

Zhou, Hailong; Wu, Tao; Dong, Xiuli; Wang, Qi; Shen, Jiawei

2007-01-01

Many properties and functions of bone-related proteins perform through the interface with the hydroxyapatite. However, the mechanism of difference of proteins adsorbing behaviors caused by the variation of calcium and phosphate ions on hydroxyapatite is still unclear at atomic level. In this work, we investigated the site-selective adhesion and the adsorption mechanism of protein BMP-7 to the hydroxyapatite surfaces in aqueous media during adsorption and desorption processes. Molecular dynamics (MD) and steered molecular dynamics (SMD) simulations combined with trajectory analysis were employed to give insight into the underlying behaviors of BMP-7 binding. The results suggest that the adsorption sites could be divided into two categories: COO - and NH 2 /NH3+. For COO - , the adsorption phenomenon is driven by the electrostatic interaction formed between the negative charged carboxylate groups and the Ca1 cations on the hydroxyapatite surface. While for NH 2 /NH3+, the interaction is through the intermolecular H-bonds between the N-containing groups and the phosphate on the hydroxyapatite surface

Surface-modified polymeric pads for enhanced performance during chemical mechanical planarization

International Nuclear Information System (INIS)

Deshpande, S.; Dakshinamurthy, S.; Kuiry, S.C.; Vaidyanathan, R.; Obeng, Y.S.; Seal, S.

2005-01-01

The chemical mechanical planarization (CMP) process occurs at an atomic level at the slurry/wafer interface and hence slurries and polishing pads play a critical role in their successful implementation. Polyurethane is a commonly used polymer in the manufacturing of CMP pads. These pads are incompatible with some chemicals present in the CMP slurries, such as hydrogen peroxide. To overcome these problems, Psiloquest has developed new Application Specific Pads (ASP). Surface of such pads has been modified by depositing a thin film of tetraethyl orthosilicate using plasma-enhanced chemical vapor deposition (PECVD) process. In the present study, mechanical properties of such coated pads have been investigated using nanoindentation. The surface morphology and the chemistry of the ASP were studied using scanning electron microcopy, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy techniques. It was observed that mechanical and chemical properties of the pad top surface are a function of the PECVD coating time. Such PECVD-treated pads are found to be hydrophilic and do not require storage in aqueous media during the not-in-use period. The metal removal rate using such surface-modified polishing pads was found to increase linearly with the PECVD coating time

Surface/subsurface observation and removal mechanisms of ground reaction bonded silicon carbide

Science.gov (United States)

Yao, Wang; Zhang, Yu-Min; Han, Jie-cai; Zhang, Yun-long; Zhang, Jian-han; Zhou, Yu-feng; Han, Yuan-yuan

2006-01-01

Reaction Bonded Silicon Carbide (RBSiC) has long been recognized as a promising material for optical applications because of its unique combination of favorable properties and low-cost fabrication. Grinding of silicon carbide is difficult because of its high hardness and brittleness. Grinding often induces surface and subsurface damage, residual stress and other types of damage, which have great influence on the ceramic components for optical application. In this paper, surface integrity, subsurface damage and material removal mechanisms of RBSiC ground using diamond grinding wheel on creep-feed surface grinding machine are investigated. The surface and subsurface are studied with scanning electron microscopy (SEM) and optical microscopy. The effects of grinding conditions on surface and subsurface damage are discussed. This research links the surface roughness, surface and subsurface cracks to grinding parameters and provides valuable insights into the material removal mechanism and the dependence of grind induced damage on grinding conditions.

Contact mechanics for layered materials with randomly rough surfaces.

Science.gov (United States)

Persson, B N J

2012-03-07

The contact mechanics model of Persson is applied to layered materials. We calculate the M function, which relates the surface stress to the surface displacement, for a layered material, where the top layer (thickness d) has different elastic properties than the semi-infinite solid below. Numerical results for the contact area as a function of the magnification are presented for several cases. As an application, we calculate the fluid leak rate for laminated rubber seals.

Mechanical stress-controlled tunable active frequency-selective surface

Science.gov (United States)

Huang, Bo-Cin; Hong, Jian-Wei; Lo, Cheng-Yao

2017-01-01

This study proposes a tunable active frequency-selective surface (AFSS) realized by mechanically expanding or contracting a split-ring resonator (SRR) array. The proposed AFSS transfers mechanical stress from its elastic substrate to the top of the SRR, thereby achieving electromagnetic (EM) modulation without the need for an additional external power supply, meeting the requirements for the target application: the invisibility cloak. The operating mechanism of the proposed AFSS differs from those of other AFSSs, supporting modulations in arbitrary frequencies in the target range. The proposed stress-controlled or strain-induced EM modulation proves the existence of an identical and linear relationship between the strain gradient and the frequency shift, implying its suitability for other EM modulation ranges and applications.

Manager Perspectives on Communication and Public Engagement in Ecological Restoration Project Success

Science.gov (United States)

We argue that public engagement is crucial to achieving lasting ecological success in aquatic restoration efforts, and that the most effective public engagement mechanisms are what we term iterative mechanisms. Here we look to a particular social-ecological system – the restorati...

Experimental Assessment of Mechanical Night Ventilation on Inner Wall Surfaces

DEFF Research Database (Denmark)

Ji, Wenhui; Heiselberg, Per Kvols; Wang, Houhua

2016-01-01

The cooling potential of night ventilation largely depends on the heat exchange at the internal room surfaces. During night time, increased heat transfer on a vertical wall is expected due to cool supply air that flows along the internal wall surface from the top of the wall. This paper presents ...... an experimental study of the cooling of wall surfaces in a test room by mechanical night-time ventilation. Significant improvement of indoor thermal environment is presented resulting from the enhanced internal convection heat transfer....

Mechanical Balance Laws for Boussinesq Models of Surface Water Waves

Science.gov (United States)

Ali, Alfatih; Kalisch, Henrik

2012-06-01

Depth-integrated long-wave models, such as the shallow-water and Boussinesq equations, are standard fare in the study of small amplitude surface waves in shallow water. While the shallow-water theory features conservation of mass, momentum and energy for smooth solutions, mechanical balance equations are not widely used in Boussinesq scaling, and it appears that the expressions for many of these quantities are not known. This work presents a systematic derivation of mass, momentum and energy densities and fluxes associated with a general family of Boussinesq systems. The derivation is based on a reconstruction of the velocity field and the pressure in the fluid column below the free surface, and the derivation of differential balance equations which are of the same asymptotic validity as the evolution equations. It is shown that all these mechanical quantities can be expressed in terms of the principal dependent variables of the Boussinesq system: the surface excursion η and the horizontal velocity w at a given level in the fluid.

Plastic deformation to enhance plasma-assisted nitriding: On surface contamination induced by Surface Mechanical Attrition Treatment

International Nuclear Information System (INIS)

Samih, Youssef; Novelli, Marc; Bolle, Bernard; Allain, Nathalie; Fundenberger, Jean-Jacques; Marcos, Grégory; Czerwiec, Thierry; Grosdidier, Thierry; Thiriet, Tony

2014-01-01

The Surface Mechanical Attrition Treatment is a recent technique leading to the formation of nanostructured layers by the repeated action of impacting balls. While several communications have revealed possible contamination of the SMATed surfaces, the nature of this surface contamination was analyzed in the present contribution for the treatment of an AISI 316L stainless steel. It is shown, by a combination of Transmission Electron Microscopy and Glow Discharge – Optical Emission Spectrometry, that the surface was alloyed with Ti, Al and V coming from the sonotrode that is used to move the balls as well as Zr coming from the zirshot® balls themselves

Plastic deformation to enhance plasma-assisted nitriding: On surface contamination induced by Surface Mechanical Attrition Treatment

Science.gov (United States)

Samih, Youssef; Novelli, Marc; Thiriet, Tony; Bolle, Bernard; Allain, Nathalie; Fundenberger, Jean-Jacques; Marcos, Grégory; Czerwiec, Thierry; Grosdidier, Thierry

2014-08-01

The Surface Mechanical Attrition Treatment is a recent technique leading to the formation of nanostructured layers by the repeated action of impacting balls. While several communications have revealed possible contamination of the SMATed surfaces, the nature of this surface contamination was analyzed in the present contribution for the treatment of an AISI 316L stainless steel. It is shown, by a combination of Transmission Electron Microscopy and Glow Discharge - Optical Emission Spectrometry, that the surface was alloyed with Ti, Al and V coming from the sonotrode that is used to move the balls as well as Zr coming from the zirshot® balls themselves.

Characterization of surface charge and mechanical properties of chitosan/alginate based biomaterials

International Nuclear Information System (INIS)

Verma, Devendra; Desai, Malav S.; Kulkarni, Namrata; Langrana, Noshir

2011-01-01

This study aims to examine mechanical properties and surface charge characteristics of chitosan/alginate-based films for biomedical applications. By varying the concentrations of chitosan and alginate, we have developed films with varying surface charge densities and mechanical characteristics. The surface charge densities of these films were determined by applying an analytical model on force curves derived from an atomic force microscope (AFM). The average surface charge densities of films containing 60% chitosan and 80% chitosan were found to be - 0.46 mC/m 2 and - 0.32 mC/m 2 , respectively. The surface charge density of 90% chitosan containing films was found to be neutral. The elastic moduli and the water content were found to be decreasing with increasing chitosan concentration. The films with 60%, 80% and 90% chitosan gained 93.5 ± 6.6%, 217.1 ± 22.1% and 396.8 ± 67.5% of their initial weight, respectively. Their elastic moduli were found to be 2.6 ± 0.14 MPa, 1.9 ± 0.27 MPa and 0.93 ± 0.12 MPa, respectively. The trend observed in the mechanical response of these films has been attributed to the combined effect of the concentration of polyelectrolyte complexes (PEC) and the amount of water absorbed. The Fourier transform infrared spectroscopy experiments indicate the presence of higher alginate on the surface of the films compared to the bulk in all films. The presence of higher alginate on surface is consistent with negative surface charge densities of these films, determined from AFM experiments. Highlights: → Chitosan/alginate based fibrous polyelectrolyte complex films were developed. → The average surface charge density of the films was determined using AFM. → Elastic modulus of the films increased with increase in PEC content. → FTIR analysis indicated higher alginate content on surface compared to bulk.

Engaging Élitism: The Mediating Effect of Work Engagement on Affective Commitment and Quit Intentions in Two Australian University Groups

Science.gov (United States)

Ferrer, Justine L.; Morris, Leanne

2013-01-01

Some universities rely on their élitism as one mechanism to attract and retain talented faculty. This paper examines two groups of élite and non-élite universities and the mediating effect that work engagement has on affective commitment and intention to quit. Findings indicate partial support for the mediating effect of work engagement in the…

Robust tilt and lock mechanism for hopping actuator

Energy Technology Data Exchange (ETDEWEB)

Salton, Jonathan R.; Buerger, Stephen; Dullea, Kevin J.; Marron, Lisa C.; Salisbury, Curt Michael; Spletzer, Barry Louis

2017-02-07

A tilt and lock apparatus that includes a tilt servomechanism, a spiral torsion spring, a lock wheel, and a lock hook is described herein. The spiral torsion spring is mechanically coupled to the tilt servomechanism and the lock wheel (which includes an opening). When a shaft is positioned through the opening, rotation of the lock wheel is in unison with rotation of the shaft. An external surface of the lock wheel includes one or more grooves. The lock hook includes a head that engages and disengages the grooves. The lock wheel is stationary when the head engages one of the grooves and is rotatable when the head disengages the grooves. The head and the grooves are geometrically aligned when engaged to prevent creation of a force that acts to disengage the head responsive to an applied force acting on the shaft.

Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process

Energy Technology Data Exchange (ETDEWEB)

Wang, Haibo [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China); Song, Guolin [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Tang, Guoyi, E-mail: tanggy@mail.tsinghua.edu.cn [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China)

2016-04-26

The present work integrates 3D digital optical microscopy (OM), nano-indentation, X-ray diffraction (XRD), scanning electron microscopy (SEM) with electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) to systematically investigate the effect of electropulsing on the surface mechanical properties and microstructure of AISI 304 stainless steel during the ultrasonic surface rolling process (USRP). Compared with the original USRP, the introduction of electropulsing with optimal parameters can effectively facilitate surface crack healing and improve surface hardness and wear resistance dramatically, and the residual compressive stress is further enhanced. Meanwhile, more martensite phase and fewer deformation twins can be found in the strengthened layer. Rapid improvement of the surface mechanical properties should be attributed to the ultra-refined grains, accelerated martensitic phase transformation and suppressed deformation twining induced by the coupling effect of USRP and electropulsing. The high strain rate given by USRP, increased stacking fault energy and accelerated dislocation mobility caused by electropulsing are likely the primary intrinsic reasons for the observed phenomena.

Routing the asteroid surface vehicle with detailed mechanics

Science.gov (United States)

Yu, Yang; Baoyin, He-Xi

2014-06-01

The motion of a surface vehicle on/above an irregular object is investigated for a potential interest in the insitu explorations to asteroids of the solar system. A global valid numeric method, including detailed gravity and geomorphology, is developed to mimic the behaviors of the test particles governed by the orbital equations and surface coupling effects. A general discussion on the surface mechanical environment of a specified asteroid, 1620 Geographos, is presented to make a global evaluation of the surface vehicle's working conditions. We show the connections between the natural trajectories near the ground and differential features of the asteroid surface, which describes both the good and bad of typical terrains from the viewpoint of vehicles' dynamic performances. Monte Carlo simulations are performed to take a further look at the trajectories of particles initializing near the surface. The simulations reveal consistent conclusions with the analysis, i.e., the open-field flat ground and slightly concave basins/valleys are the best choices for the vehicles' dynamical security. The dependence of decending trajectories on the releasing height is studied as an application; the results show that the pole direction (where the centrifugal force is zero) is the most stable direction in which the shift of a natural trajectory will be well limited after landing. We present this work as an example for pre-analysis that provides guidance to engineering design of the exploration site and routing the surface vehicles.

On two possible mechanisms of metallic island remotion from solid surface at heavy multicharged ion irradiation

International Nuclear Information System (INIS)

Vorob'eva, I.V.; Geguzin, Ya.E.; Monastyrenko, V.E.

1986-01-01

Two mechanisms of energy transfer from a moving ion to a metallic island film on a solid surface are described. A particular case when the energy transfer quantity is enough to remove an island from the solid surface breaking adhesion bond is considered. One mechanism is 'shaking off', another one is a 'jumping up' mechanism. The essence of the first mechanism is that an ion bombarding the surface excites a cylindrical shock wave with a front that can 'shake off' islands from the solid surface along the ion trajectory when it reaches the surface. An island is heated in pulsed mode, and during thermal expansion it should push off the substrate, and so it jumps up. The pure case of such mechanism is observed when an ion transverses an island and transfers energy to the latter one that is defined by the quantity of ion energy losses in the island

Sub-discretized surface model with application to contact mechanics in multi-body simulation

Energy Technology Data Exchange (ETDEWEB)

Johnson, S; Williams, J

2008-02-28

The mechanics of contact between rough and imperfectly spherical adhesive powder grains are often complicated by a variety of factors, including several which vary over sub-grain length scales. These include several traction factors that vary spatially over the surface of the individual grains, including high energy electron and acceptor sites (electrostatic), hydrophobic and hydrophilic sites (electrostatic and capillary), surface energy (general adhesion), geometry (van der Waals and mechanical), and elasto-plastic deformation (mechanical). For mechanical deformation and reaction, coupled motions, such as twisting with bending and sliding, as well as surface roughness add an asymmetry to the contact force which invalidates assumptions for popular models of contact, such as the Hertzian and its derivatives, for the non-adhesive case, and the JKR and DMT models for adhesive contacts. Though several contact laws have been offered to ameliorate these drawbacks, they are often constrained to particular loading paths (most often normal loading) and are relatively complicated for computational implementation. This paper offers a simple and general computational method for augmenting contact law predictions in multi-body simulations through characterization of the contact surfaces using a hierarchically-defined surface sub-discretization. For the case of adhesive contact between powder grains in low stress regimes, this technique can allow a variety of existing contact laws to be resolved across scales, allowing for moments and torques about the contact area as well as normal and tangential tractions to be resolved. This is especially useful for multi-body simulation applications where the modeler desires statistical distributions and calibration for parameters in contact laws commonly used for resolving near-surface contact mechanics. The approach is verified against analytical results for the case of rough, elastic spheres.

Surface effects on the mechanical properties of nanoporous materials

International Nuclear Information System (INIS)

Xia Re; Li Xide; Feng Xiqiao; Qin Qinghua; Liu Jianlin

2011-01-01

Using the theory of surface elasticity, we investigate the mechanical properties of nanoporous materials. The classical theory of porous materials is modified to account for surface effects, which become increasingly important as the characteristic sizes of microstructures shrink to nanometers. First, a refined Timoshenko beam model is presented to predict the effective elastic modulus of nanoporous materials. Then the surface effects on the elastic microstructural buckling behavior of nanoporous materials are examined. In particular, nanoporous gold is taken as an example to illustrate the application of the proposed model. The results reveal that both the elastic modulus and the critical buckling behavior of nanoporous materials exhibit a distinct dependence on the characteristic sizes of microstructures, e.g. the average ligament width.

Surface effects on the mechanical properties of nanoporous materials

Energy Technology Data Exchange (ETDEWEB)

Xia Re [School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072 (China); Li Xide; Feng Xiqiao [AML, Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China); Qin Qinghua [School of Engineering, Australian National University, Canberra, ACT 0200 (Australia); Liu Jianlin, E-mail: fengxq@tsinghua.edu.cn [Department of Engineering Mechanics, China University of Petroleum, Qingdao 266555 (China)

2011-07-01

Using the theory of surface elasticity, we investigate the mechanical properties of nanoporous materials. The classical theory of porous materials is modified to account for surface effects, which become increasingly important as the characteristic sizes of microstructures shrink to nanometers. First, a refined Timoshenko beam model is presented to predict the effective elastic modulus of nanoporous materials. Then the surface effects on the elastic microstructural buckling behavior of nanoporous materials are examined. In particular, nanoporous gold is taken as an example to illustrate the application of the proposed model. The results reveal that both the elastic modulus and the critical buckling behavior of nanoporous materials exhibit a distinct dependence on the characteristic sizes of microstructures, e.g. the average ligament width.

Mechanically durable underwater superoleophobic surfaces based on hydrophilic bulk metals for oil/water separation

Science.gov (United States)

Yu, Huadong; Lian, Zhongxu; Xu, Jinkai; Wan, Yanling; Wang, Zuobin; Li, Yiquan; Yu, Zhanjiang; Weng, Zhankun

2018-04-01

Despite the success of previous methods for fabricating underwater superoleophobic surfaces, most of the surfaces based on soft materials are prone to collapse and deformation due to their mechanically fragile nature, and they fail to perform their designed functions after the surface materials are damaged in water. In this work, the nanosecond laser-induced oxide coatings on hydrophilic bulk metals are reported which overcomes the limitation and shows the robust underwater superoleophobicity to a mechanical challenge encountered by surfaces deployed in water environment. The results show that the surface materials have the advantage that the underwater superoleophobicity is still preserved after the surfaces are scratched by knife or sandpaper and even completely destroyed because of the hydrophilic property of damaged materials in water. It is important that the results provide a guide for the design of durable underwater superoleophobic surfaces, and the development of superoleophobic materials in many potential applications such as the oil-repellent and the oil/water separation. Additionally, the nanosecond laser technology is simple, cost-effective and suitable for the large-area and mass fabrication of mechanically durable underwater superoleophobic metal materials.

Tribochemical interaction between nanoparticles and surfaces of selective layer during chemical mechanical polishing

International Nuclear Information System (INIS)

Ilie, Filip

2013-01-01

Nanoparticles have been widely used in polish slurries such as those in the chemical mechanical polishing (CMP) process. For understanding the mechanisms of CMP, an atomic force microscope (AFM) is used to characterize polished surfaces of selective layers, after a set of polishing experiments. To optimize the CMP polishing process, one needs to get information on the interaction between the nano-abrasive slurry nanoparticles and the surface of selective layer being polished. The slurry used in CMP process of the solid surfaces is slurry with large nanoparticle size colloidal silica sol nano-abrasives. Silica sol nano-abrasives with large nanoparticle are prepared and characterized by transmission electron microscopy, particles colloidal size, and Zeta potential in this paper. The movement of nanoparticles in liquid and the interaction between nanoparticles and solid surfaces coating with selective layer are very important to obtain an atomic alloy smooth surface in the CMP process. We investigate the nanoparticle adhesion and removal processes during CMP and post-CMP cleaning. The mechanical interaction between nanoparticles and the wafer surface was studied using a microcontact wear model. This model considers the nanoparticle effects between the polishing interfaces during load balancing. Experimental results on polishing and cleaning are compared with numerical analysis. This paper suggests that during post-CMP cleaning, a combined effort in chemical and mechanical interaction (tribochemical interactions) would be effective in removal of small nanoparticles during cleaning. For large nanoparticles, more mechanical forces would be more effective. CMP results show that the removal rate has been improved to 367 nm/min and root mean square (RMS) of roughness has been reduced from 4.4 to 0.80 nm. Also, the results show that the silica sol nano-abrasives about 100 nm are of higher stability (Zeta potential is −65 mV) and narrow distribution of nanoparticle

Virtual Learning Environment for Interactive Engagement with Advanced Quantum Mechanics

Science.gov (United States)

Pedersen, Mads Kock; Skyum, Birk; Heck, Robert; Müller, Romain; Bason, Mark; Lieberoth, Andreas; Sherson, Jacob F.

2016-01-01

A virtual learning environment can engage university students in the learning process in ways that the traditional lectures and lab formats cannot. We present our virtual learning environment "StudentResearcher," which incorporates simulations, multiple-choice quizzes, video lectures, and gamification into a learning path for quantum…

Surface scattering mechanisms of tantalum nitride thin film resistor.

Science.gov (United States)

Chen, Huey-Ru; Chen, Ying-Chung; Chang, Ting-Chang; Chang, Kuan-Chang; Tsai, Tsung-Ming; Chu, Tian-Jian; Shih, Chih-Cheng; Chuang, Nai-Chuan; Wang, Kao-Yuan

2014-01-01

In this letter, we utilize an electrical analysis method to develop a TaN thin film resistor with a stricter spec and near-zero temperature coefficient of resistance (TCR) for car-used electronic applications. Simultaneously, we also propose a physical mechanism mode to explain the origin of near-zero TCR for the TaN thin film resistor (TFR). Through current fitting, the carrier conduction mechanism of the TaN TFR changes from hopping to surface scattering and finally to ohmic conduction for different TaN TFRs with different TaN microstructures. Experimental data of current-voltage measurement under successive increasing temperature confirm the conduction mechanism transition. A model of TaN grain boundary isolation ability is eventually proposed to influence the carrier transport in the TaN thin film resistor, which causes different current conduction mechanisms.

Triggers for the critical engagement with decision support systems

NARCIS (Netherlands)

Hartmann, Timo; Javernick-Will, A.; Chinowsky, P.

2012-01-01

In previous work, we showed that the critical engagement with a decision sup- port system during its implementation by a project team is an important an- tecedent for the successful later use of the technology. However, the mechanisms that trigger such critical engagement are so far not well

Mechanisms regulating osteoblast response to surface microtopography and vitamin D

Science.gov (United States)

Bell, Bryan Frederick, Jr.

A comprehensive understanding of the interactions between orthopaedic and dental implant surfaces with the surrounding host tissue is essential in the design of advanced biomaterials that better promote bone growth and osseointegration of implants. Dental implants with roughened surfaces and high surface energy are well known to promote osteoblast differentiation in vitro and promote increased bone-to-implant contact in vivo. In addition, increased surface roughness increases osteoblasts response to the vitamin D metabolite 1alpha,25(OH)2D3. However, the exact mechanisms mediating cell response to surface properties and 1alpha,25(OH)2D3 are still being elucidated. The central aim of the thesis is to investigate whether integrin signaling in response to rough surface microtopography enhances osteoblast differentiation and responsiveness to 1alpha,25(OH)2D3. The hypothesis is that the integrin alpha5beta1 plays a role in osteoblast response to surface microtopography and that 1alpha,25(OH) 2D3 acts through VDR-independent pathways involving caveolae to synergistically enhance osteoblast response to surface roughness and 1alpha,25(OH) 2D3. To test this hypothesis the objectives of the studies performed in this thesis were: (1) to determine if alpha5beta 1 signaling is required for osteoblast response to surface microstructure; (2) to determine if increased responsiveness to 1alpha,25(OH)2D 3 requires the vitamin D receptor, (3) to determine if rough titanium surfaces functionalized with the peptides targeting integrins (RGD) and transmembrane proteoglycans (KRSR) will enhance both osteoblast proliferation and differentiation, and (4) to determine whether caveolae, which are associated with integrin and 1alpha,25(OH)2D3 signaling, are required for enhance osteogenic response to surface microstructure and 1alpha,25(OH)2D 3. The results demonstrate that integrins, VDR, and caveolae play important roles in mediating osteoblast response to surface properties and 1alpha,25

Multifunctional Nano-engineered Polymer Surfaces with Enhanced Mechanical Resistance and Superhydrophobicity

Science.gov (United States)

Hernández, Jaime J.; Monclús, Miguel A.; Navarro-Baena, Iván; Viela, Felipe; Molina-Aldareguia, Jon M.; Rodríguez, Isabel

2017-03-01

This paper presents a multifunctional polymer surface that provides superhydrophobicity and self-cleaning functions together with an enhancement in mechanical and electrical performance. These functionalities are produced by nanoimprinting high aspect ratio pillar arrays on polymeric matrix incorporating functional reinforcing elements. Two distinct matrix-filler systems are investigated specifically, Carbon Nanotube reinforced Polystyrene (CNT-PS) and Reduced Graphene Oxide reinforced Polyvinylidene Difluoride (RGO-PVDF). Mechanical characterization of the topographies by quantitative nanoindentation and nanoscratch tests are performed to evidence a considerable increase in stiffness, Young’s modulus and critical failure load with respect to the pristine polymers. The improvement on the mechanical properties is rationalized in terms of effective dispersion and penetration of the fillers into the imprinted structures as determined by confocal Raman and SEM studies. In addition, an increase in the degree of crystallization for the PVDF-RGO imprinted nanocomposite possibly accounts for the larger enhancement observed. Improvement of the mechanical ruggedness of functional textured surfaces with appropriate fillers will enable the implementation of multifunctional nanotextured materials in real applications.

Hot Electron Photoemission from Plasmonic Nanoparticles: Role of Transient Absorption in Surface Mechanism

DEFF Research Database (Denmark)

Uskov, Alexander V.; Protsenko, Igor E.; Ikhsanov, Renat S.

2014-01-01

We analyze and compare surface- and vol ume-based internal photoelectric effects from spherical nanoparticles, obtaining analytical expression s for the photoemission rate in both cases. Similar to results for a flat metal surface, one can show that the surface mechanism preva ils, since it is un...

Effects of Surface Roughness and Mechanical Properties of Cover-Layer on Near-Field Optical Recording

Science.gov (United States)

Kim, Jin-Hong; Lee, Jun-Seok; Lim, Jungshik; Seo, Jung-Kyo

2009-03-01

Narrow gap distance in cover-layer incident near-field recording (NFR) configuration causes a collision problem in the interface between a solid immersion lens and a disk surface. A polymer cover-layer with smooth surface results in a stable gap servo while a nanocomposite cover-layer with high refractive index shows a collision problem during the gap servo test. Even though a dielectric cover-layer, in which the surface is rougher than the polymer, supplements the mechanical properties, an unclear eye pattern due to an unstable gap servo can be obtained after a chemical mechanical polishing. Not only smooth surface but also good mechanical properties of cover-layer are required for the stable gap servo in the NFR.

Ocular surface immunity: homeostatic mechanisms and their disruption in dry eye disease.

Science.gov (United States)

Barabino, Stefano; Chen, Yihe; Chauhan, Sunil; Dana, Reza

2012-05-01

The tear film, lacrimal glands, corneal and conjunctival epithelia and Meibomian glands work together as a lacrimal functional unit (LFU) to preserve the integrity and function of the ocular surface. The integrity of this unit is necessary for the health and normal function of the eye and visual system. Nervous connections and systemic hormones are well known factors that maintain the homeostasis of the ocular surface. They control the response to internal and external stimuli. Our and others' studies show that immunological mechanisms also play a pivotal role in regulating the ocular surface environment. Our studies demonstrate how anti-inflammatory factors such as the expression of vascular endothelial growth factor receptor-3 (VEGFR-3) in corneal cells, immature corneal resident antigen-presenting cells, and regulatory T cells play an active role in protecting the ocular surface. Dry eye disease (DED) affects millions of people worldwide and negatively influences the quality of life for patients. In its most severe forms, DED may lead to blindness. The etiology and pathogenesis of DED remain largely unclear. Nonetheless, in this review we summarize the role of the disruption of afferent and efferent immunoregulatory mechanisms that are responsible for the chronicity of the disease, its symptoms, and its clinical signs. We illustrate current anti-inflammatory treatments for DED and propose that prevention of the disruption of immunoregulatory mechanisms may represent a promising therapeutic strategy towards controlling ocular surface inflammation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Bioadhesion of mussels and geckos: Molecular mechanics, surface chemistry, and nanoadhesives

Science.gov (United States)

Lee, Haeshin

The adhesive strategies of living creatures are diverse, ranging from temporary to permanent adhesions with various functions such as locomotion, self-defense, communication, colony formation, and so on. The classic example of temporary adhesion is the gecko, which is known for its ability to walk along vertical and even inverted surfaces; this remarkable adhesion arises from the interfacial weak interactions of van der Waals and capillary forces. In contrast, a celerbrated example of permanent adhesion is found in marine mussels which secrete protein adhesives that function in aqueous environments without mechanical failure against turbulent conditions on the seashore. In addition, mussel adhesives stick to virtually all inorganic and organic surfaces. However, most commonly used man-made adhesives lack such unique adhesion properties compared to their natural counterparts. For example, many commercial adhesives quickly lose their adhesive strength when exposed to solvents, particularly water. The first part of this thesis focused on adhesion mechanics of mussels at a single-molecule level, in which the adhesive molecule showed surprisingly strong yet reversible adhesion on inorganic surfaces but exhibited irreversible covalent bond formation on organic surfaces. Strong and reversible adhesion on mucin surfaces was found, indicating potential application for drug delivery via mucus layers. Next, inspired by the mussel's versatile adhesion on a wide variety of material surfaces, a material-independent surface modification chemistry called 'polydopamine coating' is described. This concept was subsequently adapted to develop a surface-independent polymeric primer for layer-by-layer assembly of multifunctional coatings. Finally, a new bio-hybrid adhesive 'geckel' was developed by the functional combination of adhesion strategies of geckos and mussels. The new bio-inspired adhesive and material-independent surface chemistry can revolutionize the research areas such as

A mechanical model for surface layer formation on self-lubricating ceramic composites

NARCIS (Netherlands)

Song, Jiupeng; Valefi, Mahdiar; de Rooij, Matthias B.; Schipper, Dirk J.

2010-01-01

To predict the thickness of a self-lubricating layer on the contact surface of ceramic composite material containing a soft phase during dry sliding test, a mechanical model was built to calculate the material transfer of the soft second phase in the composite to the surface. The tribological test,

On the influence of surface patterning on tissue self-assembly and mechanics.

Science.gov (United States)

Coppola, Valerio; Ventre, Maurizio; Natale, Carlo F; Rescigno, Francesca; Netti, Paolo A

2018-04-28

Extracellular matrix assembly and composition influence the biological and mechanical functions of tissues. Developing strategies to control the spatial arrangement of cells and matrix is of central importance for tissue engineering-related approaches relying on self-assembling and scaffoldless processes. Literature reports demonstrated that signals patterned on material surfaces are able to control cell positioning and matrix orientation. However, the mechanisms underlying the interactions between material signals and the structure of the de novo synthesized matrix are far from being thoroughly understood. In this work, we investigated the ordering effect provided by nanoscale topographic patterns on the assembly of tissue sheets grown in vitro. We stimulated MC3T3-E1 preosteoblasts to produce and assemble a collagen-rich matrix on substrates displaying patterns with long- or short-range order. Then, we investigated microstructural features and mechanical properties of the tissue in uniaxial tension. Our results demonstrate that patterned material surfaces are able to control the initial organization of cells in close contact to the surface; then cell-generated contractile forces profoundly remodel tissue structure towards mechanically stable spatial patterns. Such a remodelling effect acts both locally, as it affects cell and nuclear shape and globally, by affecting the gross mechanical response of the tissue. Such an aspect of dynamic interplay between cells and the surrounding matrix must be taken into account when designing material platform for the in vitro generation of tissue with specific microstructural assemblies. Copyright © 2018 John Wiley & Sons, Ltd.

Physical-mechanical image of the cell surface on the base of AFM data in contact mode

Science.gov (United States)

Starodubtseva, M. N.; Starodubtsev, I. E.; Yegorenkov, N. I.; Kuzhel, N. S.; Konstantinova, E. E.; Chizhik, S. A.

2017-10-01

Physical and mechanical properties of the cell surface are well-known markers of a cell state. The complex of the parameters characterizing the cell surface properties, such as the elastic modulus (E), the parameters of adhesive (Fa), and friction (Ff) forces can be measured using atomic force microscope (AFM) in a contact mode and form namely the physical-mechanical image of the cell surface that is a fundamental element of the cell mechanical phenotype. The paper aims at forming the physical-mechanical images of the surface of two types of glutaraldehyde-fixed cancerous cells (human epithelial cells of larynx carcinoma, HEp-2c cells, and breast adenocarcinoma, MCF-7 cells) based on the data obtained by AFM in air and revealing the basic difference between them. The average values of friction, elastic and adhesive forces, and the roughness of lateral force maps, as well as dependence of the fractal dimension of lateral force maps on Z-scale factor have been studied. We have revealed that the response of microscale areas of the HEp-2c cell surface having numerous microvilli to external mechanical forces is less expressed and more homogeneous in comparison with the response of MCF-7 cell surface.

A study of the mechanisms causing surface defects on sidewalls during Si etching for TSV (through Si via)

International Nuclear Information System (INIS)

Choi, Jae Woong; Loh, Woon Leng; Praveen, Sampath Kumar; Murphy, Ramana; Swee, Eugene Tan Kiat

2013-01-01

In this paper we report three mechanisms causing surface defects on Si sidewalls during Si etching for TSV. The first mechanism causing surface defects was a downward surface-defect formation due to the participation of the residual polymerizing gas in the transition periods between passivation steps and etch steps. The second mechanism was an upward surface-defect formation due to etchant attacking the interface between the Si and the sidewall polymer. Although the sidewall polymer was thick enough to protect the Si surface, it was not possible to avoid surface defects if the etch step was not switched to the following passivation step in time. The third mechanism was a sponge-like surface-defect formation caused by either poor polymer depositions or voids inside the sidewall polymer. The sponge-like surface defects were formed by Si isotropic etching through the weak points of the sidewall polymer. All three surface defects were considered as the major factors on TSV integration and packaging reliability issues. (paper)

Study on cavitation effect of mechanical seals with laser-textured porous surface

Science.gov (United States)

Liu, T.; Chen, H. l.; Liu, Y. H.; Wang, Q.; Liu, Z. B.; Hou, D. H.

2012-11-01

Study on the mechanisms underlying generation of hydrodynamic pressure effect associated with laser-textured porous surface on mechanical seal, is the key to seal and lubricant properties. The theory model of mechanical seals with laser-textured porous surface (LES-MS) based on cavitation model was established. The LST-MS was calculated and analyzed by using Fluent software with full cavitation model and non-cavitation model and film thickness was predicted by the dynamic mesh technique. The results indicate that the effect of hydrodynamic pressure and cavitation are the important reasons to generate liquid film opening force on LST-MS; Cavitation effect can enhance hydrodynamic pressure effect of LST-MS; The thickness of liquid film could be well predicted with the method of dynamic mesh technique on Fluent and it becomes larger as the increasing of shaft speed and the decreasing of pressure.

Study on cavitation effect of mechanical seals with laser-textured porous surface

International Nuclear Information System (INIS)

Liu, T; Chen, H l; Liu, Y H; Wang, Q; Liu, Z B; Hou, D H

2012-01-01

Study on the mechanisms underlying generation of hydrodynamic pressure effect associated with laser-textured porous surface on mechanical seal, is the key to seal and lubricant properties. The theory model of mechanical seals with laser-textured porous surface (LES-MS) based on cavitation model was established. The LST-MS was calculated and analyzed by using Fluent software with full cavitation model and non-cavitation model and film thickness was predicted by the dynamic mesh technique. The results indicate that the effect of hydrodynamic pressure and cavitation are the important reasons to generate liquid film opening force on LST-MS; Cavitation effect can enhance hydrodynamic pressure effect of LST-MS; The thickness of liquid film could be well predicted with the method of dynamic mesh technique on Fluent and it becomes larger as the increasing of shaft speed and the decreasing of pressure.

Introduction to conformal invariance in statistical mechanics and to random surface models

International Nuclear Information System (INIS)

David, F.

1995-01-01

In the first part of these lectures I give a brief and somewhat superficial introduction to the techniques of conformal invariance and to a few applications in statistical mechanics in two dimensions. My purpose is to introduce the basic ideas and some standard results for the students who are not familiar with the theory, and to introduce concepts and tools which will be useful for the other lecturers, rather than to give a complete and up to date review of the subject. In the second part I discuss several problems in the statistical mechanics of two dimensional random surfaces and membranes. As an introduction, I present some basic facts about the statistical mechanics of one-dimensional objects and polymers, which are classical examples of objects with critical properties. Then I emphasize the special role of curvature energy and of the elastic energy associated with the internal structure of membranes, and the corresponding models of random surfaces. Finally, I discuss the specific problem of self-avoiding tethered surfaces, whose critical properties are still poorly understood, and for which the applicability of some basic techniques of field theory, such as renormalization group calculations, has been understood only recently. (orig.)

Workplace surface acting and marital partner discontent: Anxiety and exhaustion spillover mechanisms.

Science.gov (United States)

Krannitz, Morgan A; Grandey, Alicia A; Liu, Songqi; Almeida, David A

2015-07-01

Surface acting (i.e., faking and suppressing emotions at work) is repeatedly linked to employee negative moods and emotional exhaustion, but the consequences may also go beyond work boundaries. We provide a unique theoretical integration of these 2 emotional labor consequences with 2 work-to-family conflict mechanisms, mood spillover and resource drain, to explain why surface acting is likely to create marital partner discontent (i.e., partner's perceived work-to-family conflict and desire for the employee to quit). A survey of 197 hotel managers and their marital partners supported that managers' surface acting was directly related to their partner wanting them to quit, and indirectly to partner's perception of work-to-family conflict via exhaustion consistent with the resource drain mechanism. Anxiety from surface acting had an indirect mediating effect on marital partner discontent through exhaustion. Importantly, controlling for dispositional negativity and job demands did not weaken these effects. Implications for theory and future research integrating work-family and emotional labor are discussed. (c) 2015 APA, all rights reserved).

Mechanical polishing as an improved surface treatment for platinum screen-printed electrodes

Directory of Open Access Journals (Sweden)

Junqiao Lee

2016-07-01

Full Text Available The viability of mechanical polishing as a surface pre-treatment method for commercially available platinum screen-printed electrodes (SPEs was investigated and compared to a range of other pre-treatment methods (UV-Ozone treatment, soaking in N,N-dimethylformamide, soaking and anodizing in aqueous NaOH solution, and ultrasonication in tetrahydrofuran. Conventional electrochemical activation of platinum SPEs in 0.5 M H2SO4 solution was ineffective for the removal of contaminants found to be passivating the screen-printed surfaces. However, mechanical polishing showed a significant improvement in hydrogen adsorption and in electrochemically active surface areas (probed by two different redox couples due to the effective removal of surface contaminants. Results are also presented that suggest that SPEs are highly susceptible to degradation by strong acidic or caustic solutions, and could potentially lead to instability in long-term applications due to continual etching of the binding materials. The ability of SPEs to be polished effectively extends the reusability of these traditionally “single-use” devices. Keywords: Screen-printed electrodes, Polishing, Platinum, Activation, Pre-treatment, Cyclic voltammetry

Whisker growth: a new mechanism for helium blistering of surfaces in complex radiation environments

International Nuclear Information System (INIS)

McDonell, W.R.

1978-01-01

Implantation of helium concurrent with the generation of large numbers of displaced atoms in surface layers of materials exposed to 252 Cf α-particles and fission fragments produces a unique form of low temperature surface blistering. The purpose of this paper is to formulate a basis for the whisker-growth mechanism for helium blistering as an aid to the specification of conditions under which the mechanism might apply

Transition absorption as a mechanism of surface photoelectron emission from metals

DEFF Research Database (Denmark)

Zhukovsky, Sergei; Protsenko, Igor E.; Ikhsanov, Renat Sh

2015-01-01

Transition absorption of a photon by an electron passingthrough a boundary between two media with different permit-tivities is described both classically and quantum mechani-cally. Transition absorption is shown to make a substantialcontribution to photoelectron emission at a metal....../semicon-ductor interface in nanoplasmonic systems, and is put forth asa possible microscopic mechanism of the surface photoelec-tric effect in photodetectors and solar cells containing plas-monic nanoparticles....

Enzymatic Treatments to Improve Mechanical Properties and Surface Hydrophobicity of Jute Fiber Membranes

Directory of Open Access Journals (Sweden)

Aixue Dong

2016-02-01

Full Text Available Fiber membranes prepared from jute fragments can be valuable, low cost, and renewable. They have broad application prospects in packing bags, geotextiles, filters, and composite reinforcements. Traditionally, chemical adhesives have been used to improve the properties of jute fiber membranes. A series of new laccase, laccase/mediator systems, and multi-enzyme synergisms were attempted. After the laccase treatment of jute fragments, the mechanical properties and surface hydrophobicity of the produced fiber membranes increased because of the cross-coupling of lignins with ether bonds mediated by laccase. The optimum conditions were a buffer pH of 4.5 and an incubation temperature of 60 °C with 0.92 U/mL laccase for 3 h. Laccase/guaiacol and laccase/alkali lignin treatments resulted in remarkable increases in the mechanical properties; in contrast, the laccase/2,2’-azino-bis-(3-ethylthiazoline-6-sulfonate (ABTS and laccase/2,6-dimethoxyphenol treatments led to a decrease. The laccase/ guaiacol system was favorable to the surface hydrophobicity of jute fiber membranes. However, the laccase/alkali lignin system had the opposite effect. Xylanase/laccase and cellulase/laccase combined treatments were able to enhance both the mechanical properties and the surface hydrophobicity of jute fiber membranes. Among these, cellulase/laccase treatment performed better; compared to mechanical properties, the surface hydrophobicity of the jute fiber membranes showed only a slight increase after the enzymatic multi-step processes.

Uncovering molecular structural mechanisms of signaling mediated by the prion protein

International Nuclear Information System (INIS)

Romano, Sebastian A.; Linden, Rafael; Silva, Jerson L.; Foguel, Debora

2009-01-01

The glycosyl phosphatidylinositol (GPI) - anchored prion protein (PrP c ), usually associated with neurodegenerative diseases, modulates various cellular responses and may scaffold multiprotein cell surface signaling complexes. Engagement of PrP c with the secretable cochaperone hop/STI 1 induces neurotrophic transmembrane signals through unknown molecular mechanisms. We addressed whether interaction of Pr P c and hop STI 1 entails structural rearrangements relevant for signaling. Circular dichroism and fluorescence spectroscopy showed that PrP c :hop/STI 1 interaction triggers loss of PrP helical structures, involving at least a perturbation of the Pr P c 143-153 beta-helix. Novel SAXS models revealed a significant C-terminal compaction of hop/STI 1 when bound to PrP c . Differing from a recent dimeric model of human hop/STI 1, both size exclusion chromatography and SAXS data support a monomeric form of free murine hop/STI 1. Changes in the Pr P c 143-153 beta-helix may engage the transmembrane signaling protein laminin receptor precursor and neural cell adhesion molecule, both of which bind that domain of Pr P c , and further ligands may be engaged by the tertiary structural changes of hop/STI 1. These reciprocal structural modifications indicate a versatile mechanism for signaling mediated by Pr P c :hop/STI 1 interaction, consistent with the hypothesis that Pr P c scaffolds multiprotein signaling complexes at the cell surface. (author)

Uncovering molecular structural mechanisms of signaling mediated by the prion protein

Energy Technology Data Exchange (ETDEWEB)

Romano, Sebastian A.; Linden, Rafael [Universidade Federal do Rio de Janeiro (IBCCF/UFRl), RJ (Brazil). Inst. de Biofisica Carlos Chagas Filho; Cordeiro, Yraima; Rocha e Lima, Luis M.T. da [Universidade Federal do Rio de Janeiro (FF/UFRl), RJ (Brazil). Fac. de Farmacia; Lopes, Marilene H. [Instituto Ludwig de Pesquisa de Cancer, Sao Paulo, SP (Brazil); Silva, Jerson L.; Foguel, Debora [Universidade Federal do Rio de Janeiro (IBqM/UFRl), RJ (Brazil). Inst. de Bioquimica Medica

2009-07-01

The glycosyl phosphatidylinositol (GPI) - anchored prion protein (PrP{sup c}), usually associated with neurodegenerative diseases, modulates various cellular responses and may scaffold multiprotein cell surface signaling complexes. Engagement of PrP{sup c} with the secretable cochaperone hop/STI 1 induces neurotrophic transmembrane signals through unknown molecular mechanisms. We addressed whether interaction of Pr P{sup c} and hop STI 1 entails structural rearrangements relevant for signaling. Circular dichroism and fluorescence spectroscopy showed that PrP{sup c}:hop/STI 1 interaction triggers loss of PrP helical structures, involving at least a perturbation of the Pr P{sup c}{sub 143-153} beta-helix. Novel SAXS models revealed a significant C-terminal compaction of hop/STI 1 when bound to PrP{sup c}. Differing from a recent dimeric model of human hop/STI 1, both size exclusion chromatography and SAXS data support a monomeric form of free murine hop/STI 1. Changes in the Pr P{sup c}{sub 143-153} beta-helix may engage the transmembrane signaling protein laminin receptor precursor and neural cell adhesion molecule, both of which bind that domain of Pr P{sup c}, and further ligands may be engaged by the tertiary structural changes of hop/STI 1. These reciprocal structural modifications indicate a versatile mechanism for signaling mediated by Pr P{sup c}:hop/STI 1 interaction, consistent with the hypothesis that Pr P{sup c} scaffolds multiprotein signaling complexes at the cell surface. (author)

Mechanics of nanowire/nanotube in-surface buckling on elastomeric substrates

Energy Technology Data Exchange (ETDEWEB)

Xiao, J; Huang, Y [Department of Mechanical Engineering, Northwestern University, Evanston, IL 60208 (United States); Ryu, S Y; Paik, U [Division of Materials Science and Engineering, Hanyang University, 17 Hangdang-dong, Sungdong-gu, Seoul 133-791 (Korea, Republic of); Hwang, K-C [Department of Engineering Mechanics, Tsinghua University, Beijing 100084 (China); Rogers, J A, E-mail: y-huang@northwestern.edu, E-mail: jrogers@uiuc.edu [Department of Materials Science and Engineering, Frederick-Seitz Materials Research Laboratory and Beckman Institute, University of Illinois at Urbana-Champaign, Illinois 61801 (United States)

2010-02-26

A continuum mechanics theory is established for the in-surface buckling of one-dimensional nanomaterials on compliant substrates, such as silicon nanowires on elastomeric substrates observed in experiments. Simple analytical expressions are obtained for the buckling wavelength, amplitude and critical buckling strain in terms of the bending and tension stiffness of the nanomaterial and the substrate elastic properties. The analysis is applied to silicon nanowires, single-walled carbon nanotubes, multi-walled carbon nanotubes, and carbon nanotube bundles. For silicon nanowires, the measured buckling wavelength gives Young's modulus to be 140 GPa, which agrees well with the prior experimental studies. It is shown that the energy for in-surface buckling is lower than that for normal (out-of-surface) buckling, and is therefore energetically favorable.

Mechanics of nanowire/nanotube in-surface buckling on elastomeric substrates

International Nuclear Information System (INIS)

Xiao, J; Huang, Y; Ryu, S Y; Paik, U; Hwang, K-C; Rogers, J A

2010-01-01

A continuum mechanics theory is established for the in-surface buckling of one-dimensional nanomaterials on compliant substrates, such as silicon nanowires on elastomeric substrates observed in experiments. Simple analytical expressions are obtained for the buckling wavelength, amplitude and critical buckling strain in terms of the bending and tension stiffness of the nanomaterial and the substrate elastic properties. The analysis is applied to silicon nanowires, single-walled carbon nanotubes, multi-walled carbon nanotubes, and carbon nanotube bundles. For silicon nanowires, the measured buckling wavelength gives Young's modulus to be 140 GPa, which agrees well with the prior experimental studies. It is shown that the energy for in-surface buckling is lower than that for normal (out-of-surface) buckling, and is therefore energetically favorable.

Effects of high-temperature gas dealkalization on surface mechanical properties of float glass

Science.gov (United States)

Senturk, Ufuk

The surface topography, and the near-surface structure and mechanical property changes on float glass, that was treated in atmospheres containing SOsb2, HCl, and 1,1 difluoroethane (DFE) gases, at temperatures in the glass transition region, were studied. Structure was investigated using surface sensitive infrared spectroscopy techniques (attenuated total reflectance (ATR) and diffuse reflectance (DRIFT)) and the topography was evaluated using atomic force microscopy (AFM). The results obtained from the two FTIR methods were in agreement with each other. Mechanical property characteristics of the surface were determined by measuring microhardness using a recording microindentation set-up. A simple analysis performed on the three hardness calculation methods-LVH, LVHsb2, and Lsb2VH-indicated that LVH and LVHsb2 are less effected by measurement errors and are better suited for the calculation of hardness. Contact damage characteristics of the treated glass was also studied by monitoring the crack initiation behavior during indentation, using acoustic emission. The results of the studies, aiming for the understanding of the structure, topography, and hardness property changes indicate that the treatment parameters-temperature, time, and treatment atmosphere conditions-are significant factors influencing these properties. The analysis of these results suggest a relation to exist between the three properties. This relation is used in understanding the surface mechanical properties of the treated float glasses. The difference in the thermal expansion coefficients between the dealkalized surface and bulk, the nature of surface structure changes, structural relaxation, surface water content, and glass transformation temperature are identified as the major factors having an influence on the properties. A model connecting these features is suggested. A difference in the structure, hardness, and topography on the air and tin sides of float glass is also shown to exist. The

Electrochemical studies of Copper, Tantalum and Tantalum Nitride surfaces in aqueous solutions for applications in chemical-mechanical and electrochemical-mechanical planarization

Science.gov (United States)

Sulyma, Christopher Michael

This report will investigate fundamental properties of materials involved in integrated circuit (IC) manufacturing. Individual materials (one at a time) are studied in different electrochemical environmental solutions to better understand the kinetics associated with the polishing process. Each system tries to simulate a real CMP environment in order to compare our findings with what is currently used in industry. To accomplish this, a variety of techniques are used. The voltage pulse modulation technique is useful for electrochemical processing of metal and alloy surfaces by utilizing faradaic reactions like electrodeposition and electrodissolution. A theoretical framework is presented in chapter 4 to facilitate quantitative analysis of experimental data (current transients) obtained in this approach. A typical application of this analysis is demonstrated for an experimental system involving electrochemical removal of copper surface layers, a relatively new process for abrasive-free electrochemical mechanical planarization of copper lines used in the fabrication of integrated circuits. Voltage pulse modulated electrodissolution of Cu in the absence of mechanical polishing is activated in an acidic solution of oxalic acid and hydrogen peroxide. The current generated by each applied voltage step shows a sharp spike, followed by a double-exponential decay, and eventually attains the rectangular shape of the potential pulses. For the second system in chapter 5, open-circuit potential measurements, cyclic voltammetry and Fourier transform impedance spectroscopy have been used to study pH dependent surface reactions of Cu and Ta rotating disc electrodes (RDEs) in aqueous solutions of succinic acid (SA, a complexing agent), hydrogen peroxide (an oxidizer), and ammonium dodecyl sulfate (ADS, a corrosion inhibitor for Cu). The surface chemistries of these systems are relevant for the development of a single-slurry approach to chemical mechanical planarization (CMP) of Cu

Engaging youth and transferring knowledge

International Nuclear Information System (INIS)

Mantagaris, E.

2011-01-01

Youth engagement is a key component of the work of the Nuclear Waste Management Organization (NWMO) as it collaborates with Canadians to implement Adaptive Phased Management (APM), Canada's plan for the long-term management of used nuclear fuel. Knowledge transfer is an important aspect of APM implementation, which will span several decades and will need to be flexible enough to adjust to changing societal values and new information. By engaging youth, the NWMO is putting in place mechanisms for ongoing societal learning and capacity building, so that future generations will be well-equipped to make decisions and participate in future dialogues on APM. The NWMO convened a Youth Roundtable, comprised of 18- to 25-year-olds with a diversity of backgrounds and experience, to seek advice on the best approaches to engaging youth on this topic. In May 2009, the Roundtable presented its recommendations to the NWMO and its Advisory Council, providing valuable guidance on: development of dynamic messages and communications materials that will resonate with young people; use of new technologies and social media to engage youth where they are already connecting and conversing; and a range of activities to engage youth through the educational system and in their communities. The NWMO has begun to implement many of the Youth Roundtable recommendations and is developing longer-term implementation plans, including a framework for education and outreach to youth. Through its Corporate Social Responsibility (CSR) Program, the NWMO is laying the foundation for greater science and technology literacy and enhanced community engagement among young Canadians. Additionally, the NWMO is working with Aboriginal peoples to develop strategies for further engagement of Aboriginal youth, as part of the organization's ongoing collaborative work with Aboriginal peoples that could be affected by the implementation of APM. Youth engagement will continue to be a NWMO priority moving

Engaging youth and transferring knowledge

Energy Technology Data Exchange (ETDEWEB)

Mantagaris, E. [Nuclear Waste Management Organization, Toronto, ON (Canada)

2011-07-01

Youth engagement is a key component of the work of the Nuclear Waste Management Organization (NWMO) as it collaborates with Canadians to implement Adaptive Phased Management (APM), Canada's plan for the long-term management of used nuclear fuel. Knowledge transfer is an important aspect of APM implementation, which will span several decades and will need to be flexible enough to adjust to changing societal values and new information. By engaging youth, the NWMO is putting in place mechanisms for ongoing societal learning and capacity building, so that future generations will be well-equipped to make decisions and participate in future dialogues on APM. The NWMO convened a Youth Roundtable, comprised of 18- to 25-year-olds with a diversity of backgrounds and experience, to seek advice on the best approaches to engaging youth on this topic. In May 2009, the Roundtable presented its recommendations to the NWMO and its Advisory Council, providing valuable guidance on: development of dynamic messages and communications materials that will resonate with young people; use of new technologies and social media to engage youth where they are already connecting and conversing; and a range of activities to engage youth through the educational system and in their communities. The NWMO has begun to implement many of the Youth Roundtable recommendations and is developing longer-term implementation plans, including a framework for education and outreach to youth. Through its Corporate Social Responsibility (CSR) Program, the NWMO is laying the foundation for greater science and technology literacy and enhanced community engagement among young Canadians. Additionally, the NWMO is working with Aboriginal peoples to develop strategies for further engagement of Aboriginal youth, as part of the organization's ongoing collaborative work with Aboriginal peoples that could be affected by the implementation of APM. Youth engagement will continue to be a NWMO priority moving

Structural changes of radial forging die surface during service under thermo-mechanical fatigue

International Nuclear Information System (INIS)

Nematzadeh, Fardin; Akbarpour, Mohammad Reza; Kokabi, Amir Hosein; Sadrnezhaad, Seyed Khatiboleslam

2009-01-01

Radial forging is one of the modern open die forging techniques and has a wide application in producing machine parts. During operation at high temperatures, severe temperature change associated with mechanical loads and the resultant wearing of the die surface lead to intense variation in strain on the die surface. Therefore, under this operating condition, thermo-mechanical fatigue (TMF) occurs on the surface of the radial forging die. TMF decreases the life of the die severely. In the present research, different layers were deposited on a 1.2714 steel die by SMAW and GTAW, with a weld wire of UDIMET 520. The microstructure of the radial forging die surface was investigated during welding and service using an optical microscope and scanning electron microscope. The results revealed that, after welding, the structure of the radial forging die surface includes the γ matrix with a homogeneous distribution of fine semi-spherical carbides. The weld structure consisted mostly of columnar dendrites with low grain boundaries. Also, microstructural investigation of the die surface during operation showed that the weld structure of the die surface has remained without any considerable change. Only dendrites were deformed and broken. Moreover, grain boundaries of the dendrites were revealed during service.

Student Engagement

DEFF Research Database (Denmark)

Conduit, Jodie; Karpen, Ingo; Farrelly, Francis

2017-01-01

system (the university), the narrow service system (the course), and the individual dyadic level of engagement (the student-lecturer interaction). These findings could be further considered and empirically tested in other engagement contexts (e.g. employee engagement, customer engagement).......Universities are seeking to actively and strategically manage student engagement through providing opportunities for students to interact and engage with the institution on a range of levels and in different ways. However, this increasingly complex and multi-layered nature of student engagement...... within a tertiary education environment is not well understood. Through qualitative focus groups and a series of interviews with undergraduate and postgraduate students, this study explores and articulates the cognitive, emotional, behavioural and social dimensions of engagement that depict the nature...

Puzzling Mechanisms

Science.gov (United States)

van Deventer, M. Oskar

2009-01-01

The basis of a good mechanical puzzle is often a puzzling mechanism. This article will introduce some new puzzling mechanisms, like two knots that engage like gears, a chain whose links can be interchanged, and flat gears that do not come apart. It illustrates how puzzling mechanisms can be transformed into real mechanical puzzles, e.g., by…

Adsorption Mechanism of Inhibitor and Guest Molecules on the Surface of Gas Hydrates.

Science.gov (United States)

Yagasaki, Takuma; Matsumoto, Masakazu; Tanaka, Hideki

2015-09-23

The adsorption of guest and kinetic inhibitor molecules on the surface of methane hydrate is investigated by using molecular dynamics simulations. We calculate the free energy profile for transferring a solute molecule from bulk water to the hydrate surface for various molecules. Spherical solutes with a diameter of ∼0.5 nm are significantly stabilized at the hydrate surface, whereas smaller and larger solutes exhibit lower adsorption affinity than the solutes of intermediate size. The range of the attractive force is subnanoscale, implying that this force has no effect on the macroscopic mass transfer of guest molecules in crystal growth processes of gas hydrates. We also examine the adsorption mechanism of a kinetic hydrate inhibitor. It is found that a monomer of the kinetic hydrate inhibitor is strongly adsorbed on the hydrate surface. However, the hydrogen bonding between the amide group of the inhibitor and water molecules on the hydrate surface, which was believed to be the driving force for the adsorption, makes no contribution to the adsorption affinity. The preferential adsorption of both the kinetic inhibitor and the spherical molecules to the surface is mainly due to the entropic stabilization arising from the presence of cavities at the hydrate surface. The dependence of surface affinity on the size of adsorbed molecules is also explained by this mechanism.

Sub-surface structures and collapse mechanisms of summit pit craters

Science.gov (United States)

Roche, O.; van Wyk de Vries, B.; Druitt, T. H.

2001-01-01

Summit pit craters are found in many types of volcanoes and are generally thought to be the product of collapse into an underpressured reservoir caused by magma withdrawal. We investigate the mechanisms and structures associated with summit pit crater formation by scaled analogue experiments and make comparisons with natural examples. Models use a sand plaster mixture as analogue rock over a cylinder of silicone simulating an underpressured magma reservoir. Experiments are carried out using different roof aspect ratios (roof thickness/roof width) of 0.2-2. They reveal two basic collapse mechanisms, dependant on the roof aspect ratio. One occurs at low aspect ratios (≤1), as illustrated by aspect ratios of 0.2 and 1. Outward dipping reverse faults initiated at the silicone margins propagates through the entire roof thickness and cause subsidence of a coherent block. Collapse along the reverse faults is accommodated by marginal flexure of the block and tension fractures at the surface (aspect ratio of 0.2) or by the creation of inward dipping normal faults delimiting a terrace (aspect ratio of 1). At an aspect ratio of 1, overhanging pit walls are the surface expressions of the reverse faults. Experiments at high aspect ratio (>1.2) reveal a second mechanism. In this case, collapse occurs by stopping, which propagates upwards by a complex pattern of both reverse faults and tension fractures. The initial underground collapse is restricted to a zone above the reservoir and creates a cavity with a stable roof above it. An intermediate mechanism occurs at aspect ratios of 1.1-1.2. In this case, stopping leads to the formation of a cavity with a thin and unstable roof, which collapses suddenly. The newly formed depression then exhibits overhanging walls. Surface morphology and structure of natural examples, such as the summit pit craters at Masaya Volcano, Nicaragua, have many of the features created in the models, indicating that the internal structural geometry of

Surface modification of Fe2O3 nanoparticles with 3-aminopropyltrimethoxysilane (APTMS): An attempt to investigate surface treatment on surface chemistry and mechanical properties of polyurethane/Fe2O3 nanocomposites

International Nuclear Information System (INIS)

Palimi, M.J.; Rostami, M.; Mahdavian, M.; Ramezanzadeh, B.

2014-01-01

Highlights: • Surface treatment of Fe 2 O 3 with amino propyl tri methoxy silane. • The surface chemistry pigments were affected by the chemical treatment. • Surface treatment of the nanoparticles by silane resulted in the significant improvement of the mechanical properties of the polyurethane coating. • The improvement was most pronounced when the nanoparticles were modified with 3 gr silane/5 g nanoparticles. - Abstract: Fe 2 O 3 nanoparticles were modified with various amounts of 3-amino propyl trimethoxy silane (APTMS). Modified and unmodified nanoparticles were introduced into the polyurethane matrix at different concentrations. Fourier transform infrared radiation (FT-IR) and X-ray photoelectron spectrophotometer (XPS) were employed in order to investigate the APTMS grafting on the nanoparticles field emission-scanning electron microscope (FE-SEM) was utilized in order to investigate nanoparticles dispersion in the polyurethane coating matrix as well as the fracture behavior of the nanocomposites. The mechanical properties of the nanocomposites were investigated by dynamic mechanical thermal analysis (DMTA) and tensile test. The FTIR spectra and XPS analysis clearly showed that APTMS was grafted on the surface of nanoparticles successfully and formed chemical bonds with the surface. Also, surface treatment of the nanoparticles by silane resulted in the significant improvement of the mechanical properties of the polyurethane coating. The improvement was most pronounced when the nanoparticles were modified with 3 gr silane/5 g nanoparticles

Influence of mechanical and chemical degradation on surface gloss of resin composite materials

NARCIS (Netherlands)

Ardu, S.; Braut, V.; Uhac, I.; Benbachir, N.; Feilzer, A.J.; Krejci, I.

2009-01-01

Purpose: To determine the changes in surface gloss of different composite materials after simulation of mechanical and chemical aging mechanisms. Methods: 36 specimens were fabricated for each material and polished with 120-, 220-, 500-, 1200-, 2400- and 4000- grit SiC abrasive paper, respectively.

Local thermal property analysis by scanning thermal microscopy of an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment

Energy Technology Data Exchange (ETDEWEB)

Guo, F.A. [Suzhou Institute for Nonferrous Metals Processing Technology, No. 200 Shenxu Road, Suzhou Industrial Park, Suzhou 215021 (China) and Unite de Thermique et d' Analyse Physique, Laboratoire d' Energetique et d' Optique, Universite de Reims, BP 1039, 51687 Reims Cedex 2 (France)]. E-mail: guofuan@yahoo.com; JI, Y.L. [Suzhou Institute for Nonferrous Metals Processing Technology, No. 200 Shenxu Road, Suzhou Industrial Park, Suzhou 215021 (China); Trannoy, N. [Unite de Thermique et d' Analyse Physique, Laboratoire d' Energetique et d' Optique, Universite de Reims, BP 1039, 51687 Reims Cedex 2 (France); Lu, J. [LASMIS, Universite de Technologie de Troyes, 12 Rue Marie Curie, Troyes 10010 (France)

2006-06-15

Scanning thermal microscopy (SThM) was used to map thermal conductivity images in an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment (SMAT). It is found that the deformed surface layer shows different thermal conductivities that strongly depend on the grain size of the microstructure: the thermal conductivity of the nanostructured surface layer decreases obviously when compared with that of the coarse-grained matrix of the sample. The role of the grain boundaries in thermal conduction is analyzed in correlation with the heat conduction mechanism in pure metal. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a tool for the thermal property and microstructural analysis of ultrafine-grained microstructures.

Formation Mechanism of Micropores on the Surface of Pure Aluminum Induced by High-Current Pulsed Electron Beam Irradiation

International Nuclear Information System (INIS)

Zou Yang; Cai Jie; Wan Ming-Zhen; Lv Peng; Guan Qing-Feng

2011-01-01

The mechanism of micropores formed on the surface of polycrystalline pure aluminum under high-current pulsed electron beam (HCPEB) irradiation is explained. It is discovered that dispersed micropores with sizes of 0.1–1 μm on the irradiated surface of pure aluminum can be successfully fabricated after HCPEB irradiation. The dominant formation mechanism of the surface micropores should be attributed to the formation of supersaturation vacancies within the near surface during the HCPEB irradiation and the migration of vacancies along grain boundaries and/or dislocations towards the irradiated surface. It is expected that the HCPEB technique will become a new method for the rapid synthesis of surface porous materials. (condensed matter: structure, mechanical and thermal properties)

A hypersonic lift mechanism with decoupled lift and drag surfaces

Science.gov (United States)

Xu, YiZhe; Xu, ZhiQi; Li, ShaoGuang; Li, Juan; Bai, ChenYuan; Wu, ZiNiu

2013-05-01

In the present study, we propose a novel lift mechanism for which the lifting surface produces only lift. This is achieved by mounting a two-dimensional shock-shock interaction generator below the lifting surface. The shock-shock interaction theory in conjunction with a three dimensional correction and checked with computational fluid dynamics (CFD) is used to analyze the lift and drag forces as function of the geometrical parameters and inflow Mach number. Through this study, though limited to only inviscid flow, we conclude that it is possible to obtain a high lift to drag ratio by suitably arranging the shock interaction generator.

The ECOUTER methodology for stakeholder engagement in translational research

OpenAIRE

Murtagh, Madeleine J.; Minion, Joel T.; Turner, Andrew; Wilson, Rebecca C.; Blell, Mwenza; Ochieng, Cynthia; Murtagh, Barnaby; Roberts, Stephanie; Butters, Oliver W.; Burton, Paul R

2017-01-01

Abstract Background Because no single person or group holds knowledge about all aspects of research, mechanisms are needed to support knowledge exchange and engagement. Expertise in the research setting necessarily includes scientific and methodological expertise, but also expertise gained through the experience of participating in research and/or being a recipient of research outcomes (as a patient or member of the public). Engagement i...

Effect of ion irradiation on the surface, structural and mechanical properties of brass

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Shahbaz; Bashir, Shazia, E-mail: shaziabashir@gcu.edu.pk; Ali, Nisar; Umm-i-Kalsoom,; Yousaf, Daniel; Faizan-ul-Haq,; Naeem, Athar; Ahmad, Riaz; Khlaeeq-ur-Rahman, M.

2014-04-01

Highlights: • Brass targets were exposed to carbon ions of energy 2 MeV. • The effect of ion dose has been investigated. • The surface morphology is investigated by SEM analysis. • XRD analysis is performed to reveal structural modification. • Mechanical properties were investigated by tensile testing and microhardness testing. - Abstract: Modifications to the surface, structural and mechanical properties of brass after ion irradiation have been investigated. Brass targets were bombarded by carbon ions of 2 MeV energy from a Pelletron linear accelerator for various fluences ranging from 56 × 10{sup 12} to 26 × 10{sup 13} ions/cm{sup 2}. A scanning electron microscope and X-ray diffractometer were utilized to analyze the surface morphology and crystallographic structure respectively. To explore the mechanical properties e.g., yield stress, ultimate tensile strength and microhardness of irradiated brass, an universal tensile testing machine and Vickers microhardness tester were used. Scanning electron microscopy results revealed an irregular and randomly distributed sputter morphology for a lower ion fluence. With increasing ion fluence, the incoherently shaped structures were transformed into dendritic structures. Nano/micro sized craters and voids, along with the appearance of pits, were observed at the maximum ion fluence. From X-ray diffraction results, no new phases were observed to be formed in the brass upon irradiation. However, a change in the peak intensity and higher and lower angle shifting were observed, which represents the generation of ion-induced defects and stresses. Analyses confirmed modifications in the mechanical properties of irradiated brass. The yield stress, ultimate tensile strength and hardness initially decreased and then increased with increasing ion fluence. The changes in the mechanical properties of irradiated brass are well correlated with surface and crystallographic modifications and are attributed to the generation

Conceptualising engagement with digital behaviour change interventions: a systematic review using principles from critical interpretive synthesis.

Science.gov (United States)

Perski, Olga; Blandford, Ann; West, Robert; Michie, Susan

2017-06-01

"Engagement" with digital behaviour change interventions (DBCIs) is considered important for their effectiveness. Evaluating engagement is therefore a priority; however, a shared understanding of how to usefully conceptualise engagement is lacking. This review aimed to synthesise literature on engagement to identify key conceptualisations and to develop an integrative conceptual framework involving potential direct and indirect influences on engagement and relationships between engagement and intervention effectiveness. Four electronic databases (Ovid MEDLINE, PsycINFO, ISI Web of Knowledge, ScienceDirect) were searched in November 2015. We identified 117 articles that met the inclusion criteria: studies employing experimental or non-experimental designs with adult participants explicitly or implicitly referring to engagement with DBCIs, digital games or technology. Data were synthesised using principles from critical interpretive synthesis. Engagement with DBCIs is conceptualised in terms of both experiential and behavioural aspects. A conceptual framework is proposed in which engagement with a DBCI is influenced by the DBCI itself (content and delivery), the context (the setting in which the DBCI is used and the population using it) and the behaviour that the DBCI is targeting. The context and "mechanisms of action" may moderate the influence of the DBCI on engagement. Engagement, in turn, moderates the influence of the DBCI on those mechanisms of action. In the research literature, engagement with DBCIs has been conceptualised in terms of both experience and behaviour and sits within a complex system involving the DBCI, the context of use, the mechanisms of action of the DBCI and the target behaviour.

Detailed analysis of surface asperity deformation mechanism in diffusion bonding of steel hollow structural components

Energy Technology Data Exchange (ETDEWEB)

Zhang, C. [School of Materials Science and Engineering, Northwestern Polytechnical University, Xi’an 710072 (China); Laboratoire de Mecanique des Contacts et des Structures (LaMCoS), INSA Lyon, 20 Avenue des Sciences, F-69621 Villeurbanne Cedex (France); Li, H. [School of Materials Science and Engineering, Northwestern Polytechnical University, Xi’an 710072 (China); Li, M.Q., E-mail: zc9997242256@126.com [School of Materials Science and Engineering, Northwestern Polytechnical University, Xi’an 710072 (China)

2016-05-15

Graphical abstract: This study focused on the detailed analysis of surface asperity deformation mechanism in diffusion bonding of steel hollow structural component. A special surface with regular patterns was processed to be joined so as to observe the extent of surface asperity deformation under different applied bonding pressures. Fracture surface characteristic combined with surface roughness profiles distinctly revealed the enhanced surface asperity deformation as the applied pressure increases. The influence of surface asperity deformation mechanism on joint formation was analyzed: (a) surface asperity deformation not only directly expanded the interfacial contact areas, but also released deformation heat and caused defects, indirectly accelerating atomic diffusion, then benefits to void shrinkage; (b) surface asperity deformation readily introduced stored energy difference between two opposite sides of interface grain boundary, resulting in strain induced interface grain boundary migration. In addition, the influence of void on interface grain boundary migration was analyzed in detail. - Highlights: • A high quality hollow structural component has been fabricated by diffusion bonding. • Surface asperity deformation not only expands the interfacial contact areas, but also causes deformation heat and defects to improve the atomic diffusion. • Surface asperity deformation introduces the stored energy difference between the two opposite sides of interface grain boundary, leading to strain induced interface grain boundary migration. • The void exerts a dragging force on the interface grain boundary to retard or stop interface grain boundary migration. - Abstract: This study focused on the detailed analysis of surface asperity deformation mechanism in similar diffusion bonding as well as on the fabrication of high quality martensitic stainless steel hollow structural components. A special surface with regular patterns was processed to be joined so as to

Measuring preschool learning engagement in the laboratory.

Science.gov (United States)

Halliday, Simone E; Calkins, Susan D; Leerkes, Esther M

2018-03-01

Learning engagement is a critical factor for academic achievement and successful school transitioning. However, current methods of assessing learning engagement in young children are limited to teacher report or classroom observation, which may limit the types of research questions one could assess about this construct. The current study investigated the validity of a novel assessment designed to measure behavioral learning engagement among young children in a standardized laboratory setting and examined how learning engagement in the laboratory relates to future classroom adjustment. Preschool-aged children (N = 278) participated in a learning-based Tangrams task and Story sequencing task and were observed based on seven behavioral indicators of engagement. Confirmatory factor analysis supported the construct validity for a behavioral engagement factor composed of six of the original behavioral indicators: attention to instructions, on-task behavior, enthusiasm/energy, persistence, monitoring progress/strategy use, and negative affect. Concurrent validity for this behavioral engagement factor was established through its associations with parent-reported mastery motivation and pre-academic skills in math and literacy measured in the laboratory, and predictive validity was demonstrated through its associations with teacher-reported classroom learning behaviors and performance in math and reading in kindergarten. These associations were found when behavioral engagement was observed during both the nonverbal task and the verbal story sequencing tasks and persisted even after controlling for child minority status, gender, and maternal education. Learning engagement in preschool appears to be successfully measurable in a laboratory setting. This finding has implications for future research on the mechanisms that support successful academic development. Copyright © 2017 Elsevier Inc. All rights reserved.

IUTAM Symposium on Surface Effects in the Mechanics of Nanomaterials and Heterostructures : Proceedings of the IUTAM Symposium

CERN Document Server

Wang, Jianxiang

2013-01-01

This volume constitutes the proceedings of the IUTAM Symposium on Surface Effects in the Mechanics of Nanomaterials and Heterostructures, held in Beijing, 8-12 August, 2010. The symposium brought together the most active scientists working in this area from the fields of solid mechanics, composites, physics, and materials science and summarized the state-of-the-art research results with a view to advancing the frontiers of mechanics and materials physics.         Nanomaterials and heterostructures have a large fraction of their atoms at surfaces and  interfaces. These atoms see a different environment to those in the interior and can have a substantial effect on the overall mechanical and physical behaviour of a material. The last decade has witnessed a growing interest in the study of surfaces and how the surface behaviour couples with that of the bulk to determine the overall system response. The papers in this proceedings cover: extension of continuum mechanics and thermodynamics to the nano-scale; ...

On-Surface Pseudo-High-Dilution Synthesis of Macrocycles: Principle and Mechanism.

Science.gov (United States)

Fan, Qitang; Wang, Tao; Dai, Jingya; Kuttner, Julian; Hilt, Gerhard; Gottfried, J Michael; Zhu, Junfa

2017-05-23

Macrocycles have attracted much attention due to their specific "endless" topology, which results in extraordinary properties compared to related linear (open-chain) molecules. However, challenges still remain in their controlled synthesis with well-defined constitution and geometry. Here, we report the successful application of the (pseudo-)high-dilution method to the conditions of on-surface synthesis in ultrahigh vacuum. This approach leads to high yields (up to 84%) of cyclic hyperbenzene ([18]-honeycombene) via an Ullmann-type reaction from 4,4″-dibromo-meta-terphenyl (DMTP) as precursor on a Ag(111) surface. The mechanism of macrocycle formation was explored in detail using scanning tunneling microscopy and X-ray photoemission spectroscopy. We propose that the dominant pathway for hyperbenzene (MTP) 6 formation is the stepwise desilverization of an organometallic (MTP-Ag) 6 macrocycle, which forms via cyclization of (MTP-Ag) 6 chains under pseudo-high-dilution conditions. The high probability of cyclization on the stage of the organometallic phase results from the reversibility of the C-Ag bond. The case is different from that in solution, in which cyclization typically occurs on the stage of a covalently bonded open-chain precursor. This difference in the cyclization mechanism on a surface compared to that in solution stems mainly from the 2D confinement exerted by the surface template, which hinders the flipping of chain segments necessary for cyclization.

Mechanism of Benzene Tribopolymerization on the RuO2 (110) Surface

Science.gov (United States)

Yang, J.; Qi, Y.; Kim, H. D.; Rappe, A. M.

2018-04-01

A tribopolymer formed on the contacts of microelectromechanical and nanoelectromechanical system (MEMS-NEMS) devices is a major concern hampering their practical use in information technology. Conductive metal oxides, such as RuO2 and ReO3 , have been regarded as promising candidate materials for MEMS-NEMS contacts due to their conductivity, hardness, and relatively chemically inert surfaces. However, recent experimental works demonstrate that trace amounts of a polymer could still form on RuO2 surfaces. We demonstrate the mechanism of this class of unexpected tribopolymer formation by conducting density-functional-theory-based computational compression experiments with benzene as the contamination gas. First, mechanical force during compression changes the benzene molecules from slightly physisorbed to strongly chemisorbed. Further compression causes deformation and chemical linkage of the benzene molecules. Finally, the two contacts detach, with one having a complex organic molecule attached and the other a more reactive surface. The complex organic molecule, which has an oxabicyclic segment, can be viewed as the rudiment of a tribopolymer, and the more reactive surface can trigger the next adsorption-reaction-tribopolymer formation cycle. Based on these results, we also predict tribopolymer formation rates by using transition-state theory and the second-order rate law. We promote a deeper understanding of tribopolymer formation (especially on metal oxides) and provide strategies for suppressing tribopolymerization.

Effect of Electropulsing-Assisted Ultrasonic Nanocrystalline Surface Modification on the Surface Mechanical Properties and Microstructure of Ti-6Al-4V Alloy

Science.gov (United States)

Ye, Yongda; Wang, Haibo; Tang, Guoyi; Song, Guolin

2018-05-01

The effect of electropulsing-assisted ultrasonic nanocrystalline surface modification (EP-UNSM) on surface mechanical properties and microstructure of Ti-6Al-4V alloy is investigated. Compared to conventional ultrasonic nanocrystalline surface modification (UNSM), EP-UNSM can effectively facilitate surface roughness and morphology, leading to excellent surface roughness (reduced from Ra 0.918 to Ra 0.028 μm by UNSM and Ra 0.019 μm by EP-UNSM) and smoother morphology with less cracks and defects. Surface friction coefficients are enhanced, resulting in lower and smoother friction coefficients. In addition, the surface-strengthened layer and ultra-refined grains are significantly enhanced with more severe plastic deformation and a greater surface hardness (a maximum hardness value of 407 HV and an effective depth of 550 μm, in comparison with the maximum hardness value of 364 HV and effective depth of 300 μm obtained by conventional UNSM). Remarkable enhancement of surface mechanical properties can be attributed to the refined gradient microstructure and the enhanced severe plastic deformation layer induced by coupling the effects of UNSM and electropulsing. The accelerated dislocation mobility and atom diffusion caused by the thermal and athermal effects of electropulsing treatment may be the primary intrinsic reasons for these improvements.

Staying Engaged: Knowledge and Research Needs in Student Engagement

Science.gov (United States)

Wang, Ming-Te; Degol, Jessica

2016-01-01

In this article, we review knowledge about student engagement and look ahead to the future of study in this area. We begin by describing how researchers in the field define and study student engagement. In particular, we describe the levels, contexts, and dimensions that constitute the measurement of engagement, summarize the contexts that shape engagement and the outcomes that result from it, and articulate person-centered approaches for analyzing engagement. We conclude by addressing limitations to the research and providing recommendations for study. Specifically, we point to the importance of incorporating more work on how learning-related emotions, personality characteristics, prior learning experiences, shared values across contexts, and engagement in nonacademic activities influence individual differences in student engagement. We also stress the need to improve our understanding of the nuances involved in developing engagement over time by incorporating more extensive longitudinal analyses, intervention trials, research on affective neuroscience, and interactions among levels and dimensions of engagement. PMID:27087833

Assessment of the mechanical properties of area-elastic sport surfaces with video analysis

NARCIS (Netherlands)

de Koning, J.J.; Nigg, B.M.; Gerritsen, K.G.M.

1997-01-01

Mechanical properties of a surface are assumed to he of importance with respect to injuries, comfort, and performance in sport. For a better understanding of the factors that do influence the etiology of injuries as well as comfort, a method was developed to compare mechanical characteristics of

Dust Tolerant Commodity Transfer Interface Mechanisms for Planetary Surfaces

Science.gov (United States)

Townsend, Ivan I.; Mueller, Robert P.; Tamasy, Gabor J.

2014-01-01

Regolith is present on most planetary surfaces such as Earth's moon, Mars, and Asteroids. If human crews and robotic machinery are to operate on these regolith covered surfaces, they must face the consequences of interacting with regolith fines which consist of particles below 100 microns in diameter down to as small as submicron scale particles. Such fine dust will intrude into mechanisms and interfaces causing a variety of problems such as contamination of clean fluid lines, jamming of mechanisms and damaging connector seals and couplings. Since multiple elements must be assembled in space for system level functionality, it will be inevitable that interfaces will be necessary for structural connections, and to pass commodities such as cryogenic liquid propellants, purge and buffer gases, water, breathing air, pressurizing gases, heat exchange fluids, power and data. When fine regolith dust is present in the environment it can be lofted into interfaces where it can compromise the utility of the interface by preventing the connections from being successfully mated, or by inducing fluid leaks or degradation of power and data transmission. A dust tolerant, hand held "quick-disconnect" cryogenic fluids connector housing has been developed at NASA KSC which can be used by astronaut crews to connect flex lines that will transfer propellants and other useful fluids to the end user. In addition, a dust tolerant, automated, cryogenic fluid, multiple connector, power and data interface mechanism prototype has been developed, fabricated and demonstrated by NASA at Kennedy Space Center (KSC). The design and operation of these prototypes are explained and discussed.

Mechanism of adhesion of epoxy resin to steel surface; Tekko hyomen to epoxy jushino secchaku mechanism

Energy Technology Data Exchange (ETDEWEB)

Nakazawa, M. [Nippon Steel Corp., Tokyo (Japan)

1994-08-01

In the present research, an adhesion-breaking test and a molecular-scale model experiment were conducted to elucidate the adhesion mechanism of epoxy resin (R) to the cold rolled steel sheet (CR) and galvanized steel sheet (GI). As for the adhesive joint strength in the humid environment, the GI is inferior in residual strength to the CR. The GI joint fracture is an interfacial fracture between the plating and adhesive agent, while the CR joint fracture is a combination of cohesive fracture and interfacial fracture. It is attributable to the difference in adhesion mechanism of R and degradation due to humidity between the surface solely of zinc and iron-containing surface. The adhesion state of R to the zinc oxide and iron oxide was observed by temperature-programed desorption in an ultrahigh vacuum. On each of both oxides, the R chemically adsorbs through bond scission between the phenoxy oxide and carbon. If the water dissociatively adsorbs onto the surface, the bond is destroyed between the zinc oxide and R. The formation of interfacial chemical bond contributes to the adhesion of R to the CR and GI. In case of GI, this band is destroyed by the interfacial infiltration of water, while it is not done in case of CR. The CR excels the GI in adhesive durability. 20 refs., 8 figs., 3 tabs.

Microstructural evolution and mechanical properties of Ti–Zr beta titanium alloy after laser surface remelting

International Nuclear Information System (INIS)

Yao, Y.; Li, X.; Wang, Y.Y.; Zhao, W.; Li, G.; Liu, R.P.

2014-01-01

Highlights: • The surface mechanical properties of the alloy have been greatly improved. • Its grain size was decreased from 100 μm to 10 μm. • The metastable ω with the size of 20–50 nm was observed in the alloy after LSR. • The strengthening effect is mainly due to fine microstructure and strengthened phase. -- Abstract: The effects of laser surface remelting (LSR) on the microstructural evolution and surface mechanical properties of Ti–Zr beta titanium alloy were investigated. The surfaces of the Ti–Zr alloy was re-melted using a CO 2 laser. X-ray diffraction, Scanning electron microscope, Transmission electron microscope, nanoindentation, and microhardness analyses were performed to evaluate the microstructural and mechanical properties of the alloy. The results showed that the alloy microstructure in the remelting region was greatly refined and homogeneous compared with that in the base material because of the rapid remelting and resolidifying. Meanwhile, the metastable hexagonal ω phases with the size of 20–50 nm was found and uniformly distributed throughout the β matrix after LSR. Phase transformation and microstructural refinement were the major microstructural changes in the alloys after LSR. The microhardness and elastic modulus in the remelted region clearly increased by 92.9% and 21.78%, respectively, compared with those in the region without laser processing. The strengthening effect of LSR on the mechanical properties of the Ti–Zr alloy was also addressed. Our results indicated that LSR was an effective method of improving the surface mechanical properties of alloys

Is a Transdisciplinary Theory of Engagement in Organized Settings Possible? A Concept Analysis of the Literature on Employee Engagement, Consumer Engagement and Patient Engagement.

Science.gov (United States)

Graffigna, Guendalina

2017-01-01

Organizations are experiencing increased competition, disruptive innovation, and continuous changes in their social and economic context. Furthermore, the decrease of resources (economic and human) in such a demanding context make it imperative for organizations to find new models and strategies to make their service delivery more sustainable at the economic, environmental and psychological levels. In such a complex scenario the concept of engagement of the individuals involved in organized settings (either as service providers or as final receivers) is a promising lever for innovation. However, despite the number of studies on the matter, the debate on engagement is still very fragmented because the corpus of literature addressing the different areas of engagement is divided and diverse in its nature. In this paper, we discuss the results of a conceptual analysis of the literature conducted in order to investigate overlapping features and areas of divergence among three different areas of investigation and application of the engagement phenomenon in organized settings: the domains of employee engagement, consumer engagement, and patient engagement. These are deliberately selected as prototypical of the phenomenon of engagement along the "inside/outside" of organizational settings. The analysis consisted in a qualitative conceptual survey? Of the scholarly literature indexed with the key terms "employee engagement," "consumer engagement," and "patient engagement." We performed a key-word based survey? Of the literature in the Scopus database. A total of 163 articles were selected and analyzed. The analysis cast light on the following areas of conceptual overlap among employee, consumer and patient engagement: (1) engagement is different from empowerment and activation; (2) engagement is a multi-componential psychological experience; (3) engagement is a self-transformative experience; (4) engagement develops within a relational context; (5) engagement is a systemic

Is a Transdisciplinary Theory of Engagement in Organized Settings Possible? A Concept Analysis of the Literature on Employee Engagement, Consumer Engagement and Patient Engagement

Directory of Open Access Journals (Sweden)

Guendalina Graffigna

2017-07-01

Full Text Available Organizations are experiencing increased competition, disruptive innovation, and continuous changes in their social and economic context. Furthermore, the decrease of resources (economic and human in such a demanding context make it imperative for organizations to find new models and strategies to make their service delivery more sustainable at the economic, environmental and psychological levels. In such a complex scenario the concept of engagement of the individuals involved in organized settings (either as service providers or as final receivers is a promising lever for innovation. However, despite the number of studies on the matter, the debate on engagement is still very fragmented because the corpus of literature addressing the different areas of engagement is divided and diverse in its nature. In this paper, we discuss the results of a conceptual analysis of the literature conducted in order to investigate overlapping features and areas of divergence among three different areas of investigation and application of the engagement phenomenon in organized settings: the domains of employee engagement, consumer engagement, and patient engagement. These are deliberately selected as prototypical of the phenomenon of engagement along the “inside/outside” of organizational settings. The analysis consisted in a qualitative conceptual survey? Of the scholarly literature indexed with the key terms “employee engagement,” “consumer engagement,” and “patient engagement.” We performed a key-word based survey? Of the literature in the Scopus database. A total of 163 articles were selected and analyzed. The analysis cast light on the following areas of conceptual overlap among employee, consumer and patient engagement: (1 engagement is different from empowerment and activation; (2 engagement is a multi-componential psychological experience; (3 engagement is a self-transformative experience; (4 engagement develops within a relational context

ToTCompute: A Novel EEG-Based TimeOnTask Threshold Computation Mechanism for Engagement Modelling and Monitoring

Science.gov (United States)

Ghergulescu, Ioana; Muntean, Cristina Hava

2016-01-01

Engagement influences participation, progression and retention in game-based e-learning (GBeL). Therefore, GBeL systems should engage the players in order to support them to maximize their learning outcomes, and provide the players with adequate feedback to maintain their motivation. Innovative engagement monitoring solutions based on players'…

Strengthening stakeholder-engaged research and research on stakeholder engagement.

Science.gov (United States)

Ray, Kristin N; Miller, Elizabeth

2017-06-01

Stakeholder engagement is an emerging field with little evidence to inform best practices. Guidelines are needed to improve the quality of research on stakeholder engagement through more intentional planning, evaluation and reporting. We developed a preliminary framework for planning, evaluating and reporting stakeholder engagement, informed by published conceptual models and recommendations and then refined through our own stakeholder engagement experience. Our proposed exploratory framework highlights contexts and processes to be addressed in planning stakeholder engagement, and potential immediate, intermediate and long-term outcomes that warrant evaluation. We use this framework to illustrate both the minimum information needed for reporting stakeholder-engaged research and the comprehensive detail needed for reporting research on stakeholder engagement.

Effect of surface machining on corrosion behavior of SA182-304 in simulated

International Nuclear Information System (INIS)

Zhang Zhiming; Wang Jianqiu; Han Enhou; Ke Wei

2015-01-01

Different machining processes of mechanical parts can cause surface damage layers with different levels. The surface deformed layer can affect the corrosion behavior and service life of these mechanical parts a lot during the following service process. As a result, it is a key issue for the fabrication of the mechanical parts with long life that the selection of proper machining parameters and the removal of surface damage. The purpose of this study is to study the influence of different turning parameters on the corrosion behavior of nuclear grade SA182-304 stainless steel widely used in the advanced pressured water reactors (PWRs). 6 kinds of samples with different surface state are prepared by a lathe with different machining parameters, such as the feed, cutting speed and back engagement of the cutting edge. The high temperature and high pressure immersion test of these samples in the simulated PWR primary watershows that machining processes can affect the microstructure and chemical composition of the formed surface oxide scales a lot. According to the experimental results, the proper machining parameters for the studied SA182-304 are suggested. (authors)

Active Learning: Engaging Students to Maximize Learning in an Online Course

Science.gov (United States)

Khan, Arshia; Egbue, Ona; Palkie, Brooke; Madden, Janna

2017-01-01

Student engagement is key to successful teaching and learning, irrespective of the content and format of the content delivery mechanism. However, engaging students presents a particular challenge in online learning environments. Unlike face-to-face courses, online courses present a unique challenge as the only social presence between the faculty…

Surface sensitization mechanism on negative electron affinity p-GaN nanowires

Science.gov (United States)

Diao, Yu; Liu, Lei; Xia, Sihao; Feng, Shu; Lu, Feifei

2018-03-01

The surface sensitization is the key to prepare negative electron affinity photocathode. The thesis emphasizes on the study of surface sensitization mechanism of p-type doping GaN nanowires utilizing first principles based on density function theory. The adsorption energy, work function, dipole moment, geometry structure, electronic structure and optical properties of Mg-doped GaN nanowires surfaces with various coverages of Cs atoms are investigated. The GaN nanowire with Mg doped in core position is taken as the sensitization base. At the initial stage of sensitization, the best adsorption site for Cs atom on GaN nanowire surface is BN, the bridge site of two adjacent N atoms. Surface sensitization generates a p-type internal surface with an n-type surface state, introducing a band bending region which can help reduce surface barrier and work function. With increasing Cs coverage, work functions decrease monotonously and the "Cs-kill" phenomenon disappears. For Cs coverage of 0.75 ML and 1 ML, the corresponding sensitization systems reach negative electron affinity state. Through surface sensitization, the absorption curves are red shifted and the absorption coefficient is cut down. All theoretical calculations can guide the design of negative electron affinity Mg doped GaN nanowires photocathode.

Energy storage and dispersion of surface acoustic waves trapped in a periodic array of mechanical resonators

DEFF Research Database (Denmark)

Dühring, Maria Bayard; Laude, Vincent; Khelif, Abdelkrim

2009-01-01

It has been shown previously that surface acoustic waves can be efficiently trapped and slowed by steep ridges on a piezoelectric substrate, giving rise to two families of shear-horizontal and vertically polarized surface waves. The mechanisms of energy storage and dispersion are explored by using...... the finite element method to model surface acoustic waves generated by high aspect ratio electrodes. A periodic model is proposed including a perfectly matched layer to simulate radiation conditions away from the sources, from which the modal distributions are found. The ratio of the mechanical energy...... confined to the electrode as compared to the total mechanical energy is calculated and is found to be increasing for increasing aspect ratio and to tend to a definite limit for the two families of surface waves. This observation is in support of the interpretation that high aspect ratio electrodes act...

Composites reinforced via mechanical interlocking of surface-roughened microplatelets within ductile and brittle matrices.

Science.gov (United States)

Libanori, R; Carnelli, D; Rothfuchs, N; Binelli, M R; Zanini, M; Nicoleau, L; Feichtenschlager, B; Albrecht, G; Studart, A R

2016-04-12

Load-bearing reinforcing elements in a continuous matrix allow for improved mechanical properties and can reduce the weight of structural composites. As the mechanical performance of composite systems are heavily affected by the interfacial properties, tailoring the interactions between matrices and reinforcing elements is a crucial problem. Recently, several studies using bio-inspired model systems suggested that interfacial mechanical interlocking is an efficient mechanism for energy dissipation in platelet-reinforced composites. While cheap and effective solutions are available at the macroscale, the modification of surface topography in micron-sized reinforcing elements still represents a challenging task. Here, we report a simple method to create nanoasperities with tailored sizes and densities on the surface of alumina platelets and investigate their micromechanical effect on the energy dissipation mechanisms of nacre-like materials. Composites reinforced with roughened platelets exhibit improved mechanical properties for both organic ductile epoxy and inorganic brittle cement matrices. Mechanical interlocking increases the modulus of toughness (area under the stress-strain curve) by 110% and 56% in epoxy and cement matrices, respectively, as compared to those reinforced with flat platelets. This interlocking mechanism can potentially lead to a significant reduction in the weight of mechanical components while retaining the structural performance required in the application field.

Mechanical Properties and Tribological Behavior of In Situ NbC/Fe Surface Composites

Science.gov (United States)

Cai, Xiaolong; Zhong, Lisheng; Xu, Yunhua

2017-01-01

The mechanical properties and tribological behavior of the niobium carbide (NbC)-reinforced gray cast iron surface composites prepared by in situ synthesis have been investigated. Composites are comprised of a thin compound layer and followed by a deep diffusion zone on the surface of gray cast iron. The graded distributions of the hardness and elastic modulus along the depth direction of the cross section of composites form in the ranges of 6.5-20.1 and 159.3-411.2 GPa, respectively. Meanwhile, dry wear tests for composites were implemented on pin-on-disk equipment at sliding speed of 14.7 × 10-2 m/s and under 5 or 20 N, respectively. The result indicates that tribological performances of composites are considerably dependent on the volume fraction and the grain size of the NbC as well as the mechanical properties of the matrices in different areas. The surface compound layer presents the lowest coefficient of friction and wear rate, and exhibits the highest wear resistance, in comparison with diffusion zone and substrate. Furthermore, the worn morphologies observed reveal the dominant wear mechanism is abrasive wear feature in compound layer and diffusion zone.

Mechanical tearing of graphene on an oxidizing metal surface

International Nuclear Information System (INIS)

George, Lijin; Gupta, Aparna; Shaina, P R; Jaiswal, Manu; Gupta, Nandita Das

2015-01-01

Graphene, the thinnest possible anticorrosion and gas-permeation barrier, is poised to transform the protective coatings industry for a variety of surface applications. In this work, we have studied the structural changes of graphene when the underlying copper surface undergoes oxidation upon heating. Single-layer graphene directly grown on a copper surface by chemical vapour deposition was annealed under ambient atmosphere conditions up to 400 °C. The onset temperature of the surface oxidation of copper is found to be higher for graphene-coated foils. Parallel arrays of graphene nanoripples are a ubiquitous feature of pristine graphene on copper, and we demonstrate that these form crucial sites for the onset of the oxidation of copper, particularly for ∼0.3–0.4 μm ripple widths. In these regions, the oxidation proceeds along the length of the nanoripples, resulting in the formation of parallel stripes of oxidized copper regions. We demonstrate from temperature-dependent Raman spectroscopy that the primary defect formation process in graphene involves boundary-type defects rather than vacancy or sp"3-type defects. This observation is consistent with a mechanical tearing process that splits graphene into small polycrystalline domains. The size of these is estimated to be sub-50 nm. (paper)

Mechanical tearing of graphene on an oxidizing metal surface.

Science.gov (United States)

George, Lijin; Gupta, Aparna; Shaina, P R; Das Gupta, Nandita; Jaiswal, Manu

2015-12-11

Graphene, the thinnest possible anticorrosion and gas-permeation barrier, is poised to transform the protective coatings industry for a variety of surface applications. In this work, we have studied the structural changes of graphene when the underlying copper surface undergoes oxidation upon heating. Single-layer graphene directly grown on a copper surface by chemical vapour deposition was annealed under ambient atmosphere conditions up to 400 °C. The onset temperature of the surface oxidation of copper is found to be higher for graphene-coated foils. Parallel arrays of graphene nanoripples are a ubiquitous feature of pristine graphene on copper, and we demonstrate that these form crucial sites for the onset of the oxidation of copper, particularly for ∼0.3-0.4 μm ripple widths. In these regions, the oxidation proceeds along the length of the nanoripples, resulting in the formation of parallel stripes of oxidized copper regions. We demonstrate from temperature-dependent Raman spectroscopy that the primary defect formation process in graphene involves boundary-type defects rather than vacancy or sp(3)-type defects. This observation is consistent with a mechanical tearing process that splits graphene into small polycrystalline domains. The size of these is estimated to be sub-50 nm.

Influence of autoclave sterilization on the surface parameters and mechanical properties of six orthodontic wires.

Science.gov (United States)

Pernier, C; Grosgogeat, B; Ponsonnet, L; Benay, G; Lissac, M

2005-02-01

Orthodontic wires are frequently packaged in individual sealed bags in order to avoid cross-contamination. The instructions on the wrapper generally advise autoclave sterilization of the package and its contents if additional protection is desired. However, sterilization can modify the surface parameters and the mechanical properties of many types of material. The aim of this research was to determine the influence of one of the most widely used sterilization processes, autoclaving (18 minutes at 134 degrees C, as recommended by the French Ministry of Health), on the surface parameters and mechanical properties of six wires currently used in orthodontics (one stainless steel alloy: Tru-Chrome RMO; two nickel-titanium shape memory alloys: Neo Sentalloy and Neo Sentalloy with Ionguard GAC; and three titanium-molybdenum alloys: TMA(R) and Low Friction TMA Ormco and Resolve GAC). The alloys were analysed on receipt and after sterilization, using surface structure observation techniques, including optical, scanning electron and atomic force microscopy and profilometry. The mechanical properties were assessed by three-point bending tests. The results showed that autoclave sterilization had no adverse effects on the surface parameters or on the selected mechanical properties. This supports the possibility for practitioners to systematically sterilize wires before placing them in the oral environment.

Engagement of CD81 induces ezrin tyrosine phosphorylation and its cellular redistribution with filamentous actin

Energy Technology Data Exchange (ETDEWEB)

Coffey, Greg P.; Rajapaksa, Ranjani; Liu, Raymond; Sharpe, Orr; Kuo, Chiung-Chi; Wald Krauss, Sharon; Sagi, Yael; Davis, R. Eric; Staudt, Louis M.; Sharman, Jeff P.; Robinson, William H.; Levy, Shoshana

2009-06-09

CD81 is a tetraspanin family member involved in diverse cellular interactions in the immune and nervous systems and in cell fusion events. However, the mechanism of action of CD81 and of other tetraspanins has not been defined. We reasoned that identifying signaling molecules downstream of CD81 would provide mechanistic clues. We engaged CD81 on the surface of Blymphocytes and identified the induced tyrosine-phosphorylated proteins by mass spectrometry. This analysis showed that the most prominent tyrosine phosphorylated protein was ezrin, an actin binding protein and a member of the ezrin-radixin-moesin family. We also found that CD81 engagement induces spleen tyrosine kinase (Syk) and that Syk was involved in tyrosine phosphorylation of ezrin. Ezrin colocalized with CD81 and F-actin upon stimulation and this association was disrupted when Syk activation was blocked. Taken together, these studies suggest a model in which CD81 interfaces between the plasma membrane and the cytoskeleton by activating Syk, mobilizing ezrin, and recruiting F-actin to facilitate cytoskeletal reorganization and cell signaling. This may be a mechanism explaining the pleiotropic effects induced in response to stimulating cells by anti-CD81 antibodies or by the hepatitis C virus, which uses this molecule as its key receptor.

Imaging of Mechanical Properties of Soft Matter. From Heterogeneous Polymer Surfaces to Single Biomolecules

NARCIS (Netherlands)

Schön, Peter Manfred; Gosa, Maria; Vancso, Gyula J.

2013-01-01

In recent years the atomic force microscope (AFM) has evolved from a high resolution imaging tool to an enabling platform for physical studies at the nanoscale including quantitative mapping of mechanical characteristics of surfaces providing simultaneous topography and mechanical property maps

CRDM with separate SCRAM latch engagement and locking

Energy Technology Data Exchange (ETDEWEB)

Dodd, Christopher D.; DeSantis, Paul K.; Stambaugh, Kevin J.; Mackovjak, Allan R.; McLaughlin, John P.; Goodyear, Brett T.; Edwards, Michael J.; Ales, Matthew W.

2018-01-09

A control rod drive mechanism (CRDM) configured to latch onto the lifting rod of a control rod assembly and including separate latch engagement and latch holding mechanisms. A CRDM configured to latch onto the lifting rod of a control rod assembly and including a four-bar linkage closing the latch, wherein the four-bar linkage biases the latch closed under force of gravity.

Mechanical, dielectric and surface analysis of hydroxyapatite doped anions for implantations

Science.gov (United States)

Helen, S.; Kumar, A. Ruban

2018-04-01

Calcium Phosphate has broad applications in field of medicine and in tissue engineering. In that hydroxyapatite is one of the calcium phosphate similar to bone and teeth mineral phase. The aim of this paper is to improve mechanical property of hydroxyapatite which has less mechanical strength by doping of ions. The ions increase its strength which can be used in various medical applications. Surface property of hydroxyapatite and electrical property of ion doped hydroxyapatite analyzed and shown that it can be used in implantations, coatings.

Determination of Mechanical and Surface Properties of Semicrystalline Polyhedral Oligomeric Silsesquioxane (POSS) Nanocomposites

National Research Council Canada - National Science Library

Moody, Laura E; Marchant, Darrell; Grabow, Wade W; Lee, Andre Y; Mabry, Joseph M

2005-01-01

INTRODUCTION: (1) Nanomodification of semicrystalline polymers -- unequalled thermal, mechanical and surface properties at low volume fractions that cannot be obtained using conventional fillers; (2...

Determination of elastic mechanical characteristics of surface coatings from analysis of signals obtained by impulse excitation

Science.gov (United States)

Nyaguly, E.; Craştiu, I.; Deac, S.; Gozman-Pop, C.; Drăgănescu, G.; Bereteu, L.

2018-01-01

Most of the surface coatings are based on the synthetic polymers, which are substances composed from very large molecules that form tough, flexible, adhesive films when applied to surfaces. The other components of surface coverings materials are pigments that provide colour, opacity, gloss and other properties. Surface coatings are two-phase composite materials: constitute a polymer matrix on the one side, and on the other side of the pigments and additives dispersed in the matrix. Their role is not only aesthetically but also to ensure anticorrosive protection or even improve some mechanical properties of coated surfaces. In this paper it will follow, starting from the mechanical properties of the substrate, the metallic sheet in general, to determine the new properties of the assembly of substrate and the two coating layers, also the determination of mechanical properties of the layers. From the analysis of vibroacoustic signals obtained by the impulse excitation of the sample, one can determine the elasticity modulus. These results come to validate the results based on finite element analysis (FEA) of the same samples.

Career Engagement: Bridging Career Counseling and Employee Engagement

Science.gov (United States)

Neault, Roberta A.; Pickerell, Deirdre A.

2011-01-01

In this article, the authors present a model of career engagement that helps bridge the gap between career counselors' focus on supporting individuals to find meaningful work and employers' desire for an engaged, productive, and committed workforce. They briefly review highlights of the employee engagement literature, introduce the Career…

Effect of ion irradiation on the surface, structural and mechanical properties of brass

Science.gov (United States)

Ahmad, Shahbaz; Bashir, Shazia; Ali, Nisar; Umm-i-Kalsoom; Yousaf, Daniel; Faizan-ul-Haq; Naeem, Athar; Ahmad, Riaz; Khlaeeq-ur-Rahman, M.

2014-04-01

Modifications to the surface, structural and mechanical properties of brass after ion irradiation have been investigated. Brass targets were bombarded by carbon ions of 2 MeV energy from a Pelletron linear accelerator for various fluences ranging from 56 × 1012 to 26 × 1013 ions/cm2. A scanning electron microscope and X-ray diffractometer were utilized to analyze the surface morphology and crystallographic structure respectively. To explore the mechanical properties e.g., yield stress, ultimate tensile strength and microhardness of irradiated brass, an universal tensile testing machine and Vickers microhardness tester were used. Scanning electron microscopy results revealed an irregular and randomly distributed sputter morphology for a lower ion fluence. With increasing ion fluence, the incoherently shaped structures were transformed into dendritic structures. Nano/micro sized craters and voids, along with the appearance of pits, were observed at the maximum ion fluence. From X-ray diffraction results, no new phases were observed to be formed in the brass upon irradiation. However, a change in the peak intensity and higher and lower angle shifting were observed, which represents the generation of ion-induced defects and stresses. Analyses confirmed modifications in the mechanical properties of irradiated brass. The yield stress, ultimate tensile strength and hardness initially decreased and then increased with increasing ion fluence. The changes in the mechanical properties of irradiated brass are well correlated with surface and crystallographic modifications and are attributed to the generation, augmentation, recombination and annihilation of the ion-induced defects.

Effect of fiber surface state on mechanical properties of Cf/Si-O-C composites

International Nuclear Information System (INIS)

Wang Song; Chen Zhaohui; Ma Qingsong; Hu Haifeng; Zheng Wenwei

2005-01-01

Three-dimensional braided carbon fiber reinforced silicon oxycarbide composites (3D-B C f /Si-O-C) were fabricated via a polysiloxane infiltration and pyrolysis route. The effects of fiber surface state on microstructure and mechanical properties of C f /Si-O-C composites were investigated. The change of carbon fiber surface state was achieved via heat treatment in vacuum. The results showed that heat treatment decreased carbon fiber surface activity due to the decrease of the amount of oxygen and nitrogen atoms. The C f /Si-O-C composites fabricated from the carbon fiber with low surface activity had excellent mechanical properties, which resulted from perfect interfacial bonding and good in situ fiber strength. The flexural strength and fracture toughness of the C f /Si-O-C composites from the treated fiber were 534 MPa and 23.4 MPa m 1/2 , respectively, which were about 7 and 11 times more than those of the composites from the as-received carbon fiber, respectively

Determination of Mechanical and Surface Properties of Semicrystalline Polyhedral Oligomeric Silsequioxane (POSS) Nanocomposites

National Research Council Canada - National Science Library

Moody, Laura E; Marchant, Darrell; Grabow, Wade W; Lee, Andre Y; Mabry, Joseph M

2005-01-01

.... This study examines the ability of POSS to improve the mechanical and surface properties of three semicrystalline polymers, fluorinated ethylene-propylene (FEP), poly(vinylidene fluoride) (PVDF...

Process induced sub-surface damage in mechanically ground silicon wafers

International Nuclear Information System (INIS)

Yang Yu; De Munck, Koen; Teixeira, Ricardo Cotrin; Swinnen, Bart; De Wolf, Ingrid; Verlinden, Bert

2008-01-01

Micro-Raman spectroscopy, scanning electron microcopy, atomic force microscopy and preferential etching were used to characterize the sub-surface damage induced by the rough and fine grinding steps used to make ultra-thin silicon wafers. The roughly and ultra-finely ground silicon wafers were examined on both the machined (1 0 0) planes and the cross-sectional (1 1 0) planes. They reveal similar multi-layer damage structures, consisting of amorphous, plastically deformed and elastically stressed layers. However, the thickness of each layer in the roughly ground sample is much higher than its counterpart layers in the ultra-finely ground sample. The residual stress after rough and ultra-fine grinding is in the range of several hundreds MPa and 30 MPa, respectively. In each case, the top amorphous layer is believed to be the result of sequential phase transformations (Si-I to Si-II to amorphous Si). These phase transformations correspond to a ductile grinding mechanism, which is dominating in ultra-fine grinding. On the other hand, in rough grinding, a mixed mechanism of ductile and brittle grinding causes multi-layer damage and sub-surface cracks

Analysis the complex interaction among flexible nanoparticles and materials surface in the mechanical polishing process

Energy Technology Data Exchange (ETDEWEB)

Han Xuesong, E-mail: hanxuesongphd@yahoo.com.cn [School of Mechanical Engineering, Tianjin University, 300072 (China); Gan, Yong X. [Department of Mechanical, Industrial and Manufacturing Engineering, University of Toledo, OH 43606 (United States)

2011-02-01

Mechanical polishing (MP), being the important technique of realizing the surface planarization, has already been widely applied in the area of microelectronic manufacturing and computer manufacturing technology. The surface planarization in the MP is mainly realized by mechanical process which depended on the microdynamic behavior of nanoparticle. The complex multibody interaction among nanoparticles and materials surface is different from interaction in the macroscopic multibody system which makes the traditional classical materials machining theory cannot accurately uncover the mystery of the surface generation in the MP. Large-scale classical molecular dynamic (MD) simulation of interaction among nanoparticles and solid surface has been carried out to investigate the physical essence of surface planarization. The particles with small impact angle can generate more uniform global planarization surface but the materials removal rate is lower. The shear interaction between particle and substrate may induce large friction torque and lead to the rotation of particle. The translation plus rotation makes the nanoparticle behaved like micro-milling tool. The results show that the nanoparticles may aggregrate together and form larger cluster thus deteriorate surface the quality. This MD simulation results illuminate that the f inal planarized surface can only be acquired by synergic behavior of all particles using various means such as cutting, impacting, scratching, indentation and so on.

Neural mechanisms of intermuscular coherence: Implications for the rectification of surface electromyography

NARCIS (Netherlands)

Boonstra, T.W.; Breakspear, M.

2012-01-01

Oscillatory activity plays a crucial role in corticospinal control of muscle synergies and is widely investigated using corticospinal and intermuscular synchronization. However, the neurophysiological mechanisms that translate these rhythmic patterns into surface electromyography (EMG) are not well

Improvement of mechanical robustness of the superhydrophobic wood surface by coating PVA/SiO2 composite polymer

Science.gov (United States)

Liu, Feng; Wang, Shuliang; Zhang, Ming; Ma, Miaolian; Wang, Chengyu; Li, Jian

2013-09-01

Improvement of the robustness of superhydrophobic surfaces is crucial for the purpose of achieving commercial applications of these surfaces in such various areas as self-cleaning, water repellency and corrosion resistance. We have investigated a fabrication of polyvinyl alcohol (PVA)/silica (SiO2) composite polymer coating on wooden substrates with super repellency toward water, low sliding angles, low contact angle hysteresis, and relatively better mechanical robustness. The composite polymer slurry, consisting of well-mixing SiO2 particles and PVA, is prepared simply and subsequently coated over wooden substrates with good adhesion. In this study, the mechanical robustness of superhydrophobic wood surfaces was evaluated. The effect of petaloid structures of the composite polymer on robustness was investigated using an abrasion test and the results were compared with those of superhydrophobic wood surfaces fabricated by other processes. The produced wood surfaces exhibited promising superhydrophobic properties with a contact angle of 159̊ and a sliding angle of 4̊, and the relatively better mechanical robustness.

Engaging Environments Enhance Motor Skill Learning in a Computer Gaming Task.

Science.gov (United States)

Lohse, Keith R; Boyd, Lara A; Hodges, Nicola J

2016-01-01

Engagement during practice can motivate a learner to practice more, hence having indirect effects on learning through increased practice. However, it is not known whether engagement can also have a direct effect on learning when the amount of practice is held constant. To address this question, 40 participants played a video game that contained an embedded repeated sequence component, under either highly engaging conditions (the game group) or mechanically identical but less engaging conditions (the sterile group). The game environment facilitated retention over a 1-week interval. Specifically, the game group improved in both speed and accuracy for random and repeated trials, suggesting a general motor-related improvement, rather than a specific influence of engagement on implicit sequence learning. These data provide initial evidence that increased engagement during practice has a direct effect on generalized learning, improving retention and transfer of a complex motor skill.

Mechanical Properties of Laminate Materials: From Surface Waves to Bloch Oscillations

DEFF Research Database (Denmark)

Liang, Z.; Willatzen, Morten; Christensen, Johan

2015-01-01

for designing Bloch oscillations in classical plate structures and show how mechanical Bloch oscillations can be generated in arrays of solid plates when the modal wavelength is gradually reduced. The design recipe describes how Bloch oscillations in classical structures of arbitrary dimensions can be generated......We propose hitherto unexplored and fully analytical insights into laminate elastic materials in a true condensed-matter-physics spirit. Pure mechanical surface waves that decay as evanescent waves from the interface are discussed, and we demonstrate how these designer Scholte waves are controlled......, and we demonstrate this numerically for structures with millimeter and centimeter dimensions in the kilohertz to megahertz range. Analytical predictions agree entirely with full wave simulations showing how elastodynamics can mimic quantum-mechanical condensed-matter phenomena....

Laser irradiation effects on the surface, structural and mechanical properties of Al-Cu alloy 2024

Science.gov (United States)

Yousaf, Daniel; Bashir, Shazia; Akram, Mahreen; kalsoom, Umm-i.-; Ali, Nisar

2014-02-01

Laser irradiation effects on surface, structural and mechanical properties of Al-Cu-Mg alloy (Al-Cu alloy 2024) have been investigated. The specimens were irradiated for various fluences ranging from 3.8 to 5.5 J/cm2 using an Excimer (KrF) laser (248 nm, 18 ns, 30 Hz) under vacuum environment. The surface and structural modifications of the irradiated targets have been investigated by scanning electron microscope (SEM) and X-ray diffractometer (XRD), respectively. SEM analysis reveals the formation of micro-sized craters along the growth of periodic surface structures (ripples) at their peripheries. The size of the craters initially increases and then decreases by increasing the laser fluence. XRD analysis shows an anomalous trend in the peak intensity and crystallite size of the specimen irradiated for various fluences. A universal tensile testing machine and Vickers microhardness tester were employed in order to investigate the mechanical properties of the irradiated targets. The changes in yield strength, ultimate tensile strength and microhardness were found to be anomalous with increasing laser fluences. The changes in the surface and structural properties of Al-Cu alloy 2024 after laser irradiation have been associated with the changes in mechanical properties.

Mechanical splitting of microtubules into protofilament bundles by surface-bound kinesin-1.

Science.gov (United States)

VanDelinder, Virginia; Adams, Peter G; Bachand, George D

2016-12-21

The fundamental biophysics of gliding microtubule (MT) motility by surface-tethered kinesin-1 motor proteins has been widely studied, as well as applied to capture and transport analytes in bioanalytical microdevices. In these systems, phenomena such as molecular wear and fracture into shorter MTs have been reported due the mechanical forces applied on the MT during transport. In the present work, we show that MTs can be split longitudinally into protofilament bundles (PFBs) by the work performed by surface-bound kinesin motors. We examine the properties of these PFBs using several techniques (e.g., fluorescence microscopy, SEM, AFM), and show that the PFBs continue to be mobile on the surface and display very high curvature compared to MT. Further, higher surface density of kinesin motors and shorter kinesin-surface tethers promote PFB formation, whereas modifying MT with GMPCPP or higher paclitaxel concentrations did not affect PFB formation.

Simulating Surface-Enhanced Hyper-Raman Scattering Using Atomistic Electrodynamics-Quantum Mechanical Models.

Science.gov (United States)

Hu, Zhongwei; Chulhai, Dhabih V; Jensen, Lasse

2016-12-13

Surface-enhanced hyper-Raman scattering (SEHRS) is the two-photon analogue of surface-enhanced Raman scattering (SERS), which has proven to be a powerful tool to study molecular structures and surface enhancements. However, few theoretical approaches to SEHRS exist and most neglect the atomistic descriptions of the metal surface and molecular resonance effects. In this work, we present two atomistic electrodynamics-quantum mechanical models to simulate SEHRS. The first is the discrete interaction model/quantum mechanical (DIM/QM) model, which combines an atomistic electrodynamics model of the nanoparticle with a time-dependent density functional theory description of the molecule. The second model is a dressed-tensors method that describes the molecule as a point-dipole and point-quadrupole object interacting with the enhanced local field and field-gradients (FG) from the nanoparticle. In both of these models, the resonance effects are treated efficiently by means of damped quadratic response theory. Using these methods, we simulate SEHRS spectra for benzene and pyridine. Our results show that the FG effects in SEHRS play an important role in determining both the surface selection rules and the enhancements. We find that FG effects are more important in SEHRS than in SERS. We also show that the spectral features of small molecules can be accurately described by accounting for the interactions between the molecule and the local field and FG of the nanoparticle. However, at short distances between the metal and molecule, we find significant differences in the SEHRS enhancements predicted using the DIM/QM and the dressed-tensors methods.

Micro-mechanisms of Surface Defects Induced on Aluminum Alloys during Plastic Deformation at Elevated Temperatures

Science.gov (United States)

Gali, Olufisayo A.

Near-surface deformed layers developed on aluminum alloys significantly influence the corrosion and tribological behavior as well as reduce the surface quality of the rolled aluminum. The evolution of the near-surface microstructures induced on magnesium containing aluminum alloys during thermomechanical processing has been investigated with the aim generating an understanding of the influence of individual forming parameters on its evolution and examine the microstructure of the roll coating induced on the mating steel roll through material transfer during rolling. The micro-mechanisms related to the various features of near-surface microstructure developed during tribological conditions of the simulated hot rolling process were identified. Thermomechanical processing experiments were performed with the aid of hot rolling (operating temperature: 550 to 460 °C, 4, 10 and 20 rolling pass schedules) and hot forming (operating temperature: 350 to 545 °C, strain rate: 4 x 10-2 s-1) tribo-simulators. The surface, near-surface features and material transfer induced during the elevated temperature plastic deformation were examined and characterized employing optical interferometry, SEM/EDS, FIB and TEM. Near-surface features characterized on the rolled aluminum alloys included; cracks, fractured intermetallic particles, aluminum nano-particles, oxide decorated grain boundaries, rolled-in oxides, shingles and blisters. These features were related to various individual rolling parameters which included, the work roll roughness, which induced the formation of shingles, rolling marks and were responsible for the redistribution of surface oxide and the enhancements of the depth of the near-surface damage. The enhanced stresses and strains experienced during rolling were related to the formation and propagation of cracks, the nanocrystalline structure of the near-surface layers and aluminum nano-particles. The mechanism of the evolution of the near-surface microstructure were

Widowhood, leisure activity engagement, and cognitive function among older adults.

Science.gov (United States)

Lee, Yura; Chi, Iris; A Palinkas, Lawrence

2018-04-10

Maintaining cognitive function is an essential aspect of successful aging. Widowhood is a salient life transition that can affect older adults' cognitive function. Leisure engagement has received increasing attention because it is still modifiable in later life to help prevent cognitive decline. Nonetheless, limited longitudinal studies have examined how widowhood influences cognitive function, and even fewer studies have tested the role of leisure activities in this relationship. This study delineated the mechanism of widowhood, leisure activity engagement, and cognitive function among older adults using a national longitudinal dataset, the Health and Retirement Study, and its supplementary dataset, the Consumption and Activities Mail Survey, which repeatedly measured individuals' leisure activity engagement. Findings showed no significant association between widowhood and cognitive function during a 4-year period. However, engagement in mental activities moderated the impact of widowhood on cognitive function. Specifically, the benefit of mental activity engagement on cognition was more pronounced among individuals who were recently widowed compared to those who were married. This implies a protective role of mental activities in the relationship between widowhood and cognitive function. Interventions with mentally stimulating activities at the community level to retain cognition among individuals in early phase widowhoodare suggested. Future studies are necessary to explore whether other factors such as changes in physical and mental health and intergenerational support from adult children during widowhood may further influence this mechanism among widowhood, leisure activities, and cognitive function.

Trust in Supervisor and Job Engagement: Mediating Effects of Psychological Safety and Felt Obligation.

Science.gov (United States)

Basit, Ameer A

2017-11-17

In the social context of job engagement, the role of trust in supervisor in predicting engagement of employees has received attention in research. Very limited research, however, has investigated the mechanisms mediating this dynamic relationship. To address this important gap in knowledge, the aim of this study was to examine psychological safety and felt obligation as two psychological mechanisms mediating the effect of trust in supervisor on job engagement. Drawing from job engagement and social exchange theories, the mediating roles of psychological safety and felt obligation in the trust-engagement relationship were empirically investigated in the Malaysian context. Using self-report questionnaires, data were collected from 337 nurses employed in a public hospital located near Kuala Lumpur, Malaysia. Results fully supported the proposed serial multiple mediator model. Trust in supervisor was indirectly related to job engagement via psychological safety followed by felt obligation. This study provides empirical evidence that trust in supervisor makes employees feel psychologically safe to employ and express their selves in their job roles. This satisfaction of the psychological safety need is interpreted by employees as an important socioemotional benefit that, in turn, makes them feel obligated to pay back to their organization through their enhanced level of job engagement. Implications for theory and practice were discussed.

The Mechanical of the Small Axisymmetric Oscillations of the Liquid with the Surface Tension Forces in Elastic Tank

Directory of Open Access Journals (Sweden)

D. A. Goncharov

2015-01-01

Full Text Available In this paper we investigate small axisymmetric oscillations of a liquid in an elastic tank. We also take into account the influence of surface tension forces. For this, we turn to the mechanical analogue of the considered mechanical system. To realize the transition to mechanical analogue we use the energy method: postulating the equality of kinetic and potential energy for the investigated mechanical system and the mechanical system analog. Due to this transition we can further investigate the oscillations of a mechanical analogue. As a mechanical analogue, we consider the oscillator in the spring. The mass of the oscillator is calculated as the weight of the fluid to make oscillations. The oscillator spring constant is calculated using the identity of equations, namely, equation of free small oscillations of the oscillator and equation of free small oscillations of the system under investigation: the fluid in the elastic tank. The identity of equations allows us to draw conclusion about the identity of the natural frequencies for the source mechanical system and the system of a mechanical analogue. Next, we take into consideration the action of the surface tension. We record the Laplace condition for excess pressure because of the forces of surface tension. Then we compile the expression for the generalized force, taking into account the phenomenon of the surface tension. Next, we write the equation of oscillations of a mechanical analogue. The surface tension, due to the introduction of the generalized force in the equation for small oscillations of the mechanical analogue will change the natural frequency of the mechanical analogue. The paper presents the appropriate dependencies. The abovementioned allows us to investigate the stability of small motions of fluid in microgravity or low gravity by studying the stability of small motions of mechanical analogue. The latter is especially important due to the design and development of advanced

On the mechanics of continua with boundary energies and growing surfaces

Science.gov (United States)

Papastavrou, Areti; Steinmann, Paul; Kuhl, Ellen

2013-06-01

Many biological systems are coated by thin films for protection, selective absorption, or transmembrane transport. A typical example is the mucous membrane covering the airways, the esophagus, and the intestine. Biological surfaces typically display a distinct mechanical behavior from the bulk; in particular, they may grow at different rates. Growth, morphological instabilities, and buckling of biological surfaces have been studied intensely by approximating the surface as a layer of finite thickness; however, growth has never been attributed to the surface itself. Here, we establish a theory of continua with boundary energies and growing surfaces of zero thickness in which the surface is equipped with its own potential energy and is allowed to grow independently of the bulk. In complete analogy to the kinematic equations, the balance equations, and the constitutive equations of a growing solid body, we derive the governing equations for a growing surface. We illustrate their spatial discretization using the finite element method, and discuss their consistent algorithmic linearization. To demonstrate the conceptual differences between volume and surface growth, we simulate the constrained growth of the inner layer of a cylindrical tube. Our novel approach toward continua with growing surfaces is capable of predicting extreme growth of the inner cylindrical surface, which more than doubles its initial area. The underlying algorithmic framework is robust and stable; it allows to predict morphological changes due to surface growth during the onset of buckling and beyond. The modeling of surface growth has immediate biomedical applications in the diagnosis and treatment of asthma, gastritis, obstructive sleep apnoea, and tumor invasion. Beyond biomedical applications, the scientific understanding of growth-induced morphological instabilities and surface wrinkling has important implications in material sciences, manufacturing, and microfabrication, with applications in

Comparative risk assessment of spill response options for a deepwater oil well blowout: Part III. Stakeholder engagement.

Science.gov (United States)

Walker, Ann Hayward; Scholz, Debra; McPeek, Melinda; French-McCay, Deborah; Rowe, Jill; Bock, Michael; Robinson, Hilary; Wenning, Richard

2018-05-25

This paper describes oil spill stakeholder engagement in a recent comparative risk assessment (CRA) project that examined the tradeoffs associated with a hypothetical offshore well blowout in the Gulf of Mexico, with a specific focus on subsea dispersant injection (SSDI) at the wellhead. SSDI is a new technology deployed during the Deepwater Horizon (DWH) oil spill response. Oil spill stakeholders include decision makers, who will consider whether to integrate SSDI into future tradeoff decisions. This CRA considered the tradeoffs associated with three sets of response strategies: (1) no intervention; (2) mechanical recovery, in-situ burning, and surface dispersants; and, (3) SSDI in addition to responses in (2). For context, the paper begins with a historical review of U.S. policy and engagement with oil spill stakeholders regarding dispersants. Stakeholder activities throughout the project involved decision-maker representatives and their advisors to inform the approach and consider CRA utility in future oil spill preparedness. Copyright © 2018 Elsevier Ltd. All rights reserved.

Employee engagement, organisational performance and individual wellbeing: Exploring the evidence, developing the theory

OpenAIRE

Truss, C.; Shantz, A.; Soane, E.; Emma, C.; Alfes, K.; Delbridge, R.

2013-01-01

The development of mainstream human resource management (HRM) theory has long been concerned with how people management can enhance performance outcomes. It is only very recently that interest has been shown in the parallel stream of research on the link between employee engagement and performance, bringing the two together to suggest that engagement may constitute the mechanism through which HRM practices impact individual and organisational performance. However, engagement has emerged as a ...

Effects of thickness and surface roughness on mechanical properties of aluminum sheets

International Nuclear Information System (INIS)

Suh, Chang Hee; Jung, Yun Chul; Kim, Young Suk

2010-01-01

The effect of thickness on the mechanical properties of Al 6K21-T4 sheet specimens under uniaxial tension was investigated. In order to reduce the thickness of the specimens without changing the microstructure and grain size, chemical etching was carried out, resulting in Al sheets ranging from 0.40 mm to 1.58 mm in thickness. Additionally, the effect of surface roughness was determined by finite element (FE) calculations performed using FE code MARC 2007. Tensile specimens of varying surface roughness were modeled and simulated. An analysis of the combined effects of the thickness and surface roughness revealed that the yield and tensile strengths decreased when the number of grains over the thickness was decreased. The ductility also decreased when reducing the thickness. An FE simulation showed that both the surface roughness and thickness affected the flow-curve shape. Moreover, the effect of the surface roughness tended to increase when decreasing the sheet thickness of specimens having the same roughness

CURVES AND AESTHETIC SURFACES GENERATED BY THE R-R-RTR MECHANISM

Directory of Open Access Journals (Sweden)

Liliana LUCA

2013-05-01

Full Text Available Let’s consider a mechanism having two driving elements with revolving movements and a RTR dyad, with elements of null length and aesthetic tracks of a point are determined on a rod, for various linear movement laws of driving elements. The generated curves revolve around x and y axes and aesthetic surfaces result.

Mechanism of protective action of surface carbide layers on titanium

International Nuclear Information System (INIS)

Chukalovskaya, T.V.; Chebotareva, N.P.; Tomashov, N.D.

1990-01-01

The protective action of surface carbide layer on titanium produced in methane atmosphere at 1000 deg C and under 6.7 kPa pressure in H 2 SO 4 solutions is studied through comparison of microsection metallographic specimens prior to and after corrosion testing (after specimen activation); through comparison of anodic characteristics after partial stripping of the layer up to its complete stripping; through analysis of the behaviour of Ti-TiC galvanic couple, and through investigation of corresponding corrosion diagrams under test conditions. It is shown that screening protective mechanism is primarily got involved in highly agressive media (high temperature and concentration of solution), and in less agressive environment the protection of titanium with carbide layer is primarily ensured by electrochemical mechanism

Workplace Bullying and Work Engagement: A Self-Determination Model.

Science.gov (United States)

Goodboy, Alan K; Martin, Matthew M; Bolkan, San

2017-06-01

This study modeled motivational mechanisms that explain the negative effects of workplace bullying on work engagement. Guided by self-determination theory, workplace bullying was predicted to decrease worker engagement indirectly, due to the denial of employees' basic psychological needs and their intrinsic motivation to work. From a sample of 243 full-time employees, serial multiple mediation models revealed that the indirect relationships between workplace bullying and work engagement (i.e., vigor, dedication, absorption) were serially mediated by basic psychological needs and intrinsic motivation to work. In support of self-determination theory, this study revealed that workplace bullying indirectly disengages employees from their work by denying them of their autonomy and relatedness needs and thwarting their motivation to perform work in a fulfilling way.

Engaged to Learn Ways of Engaging ESL Learners

Directory of Open Access Journals (Sweden)

Brian Tomlinson

2010-01-01

Full Text Available In this paper I am going to argue that our most important role as language teachers is to provide potentially engaging materials for our learners and then to make use of them in optimally engaging ways. If we do not engage our learners most of the time no amount of exposure, teaching, practice or use of the language will help them to achieve sufficient language acquisition and development.

Overview on the Surface Functionalization Mechanism and Determination of Surface Functional Groups of Plasma Treated Carbon Nanotubes.

Science.gov (United States)

Saka, Cafer

2018-01-02

The use of carbon materials for many applications is due to the unique diversity of structures and properties ranging from chemical bonds between the carbon atoms of the materials to nanostructures, crystallite alignment, and microstructures. Carbon nanotubes and other nanoscale carbonaceous materials draw much attention due to their physical and chemical properties, such as high strength, high resistance to corrosion, electrical and thermal conductivity, stability and a qualified adsorbent. Carbon-based nanomaterials, which have a relatively large specific area and layered structure, can be used as an adsorbent for efficient removal of organic and inorganic contaminants. However, one of the biggest obstacles to the development of carbon-based nanomaterials adsorbents is insolubility and the lack of functional groups on the surface. There are several approaches to introduce functional groups on carbon nanotubes. One of these approaches, plasma applications, now has an important place in the creation of surface functional groups as a flexible, fast, and environmentally friendly method. This review focuses on recent information concerning the surface functionalization and modification of plasma treated carbon nanotube. This review considers the surface properties, advantages, and disadvantages of plasma-applied carbon nanotubes. It also examines the reaction mechanisms involved in the functional groups on the surface.

Microstructure and surface mechanical properties of pulse electrodeposited nickel

Energy Technology Data Exchange (ETDEWEB)

Ul-Hamid, A., E-mail: anwar@kfupm.edu.sa [Center of Research Excellence in Corrosion (CoRE-C), Research Institute, King Fahd University of Petroleum and Minerals, P.O. Box 1073, Dhahran 31261 (Saudi Arabia); Dafalla, H.; Quddus, A.; Saricimen, H.; Al-Hadhrami, L.M. [Center of Research Excellence in Corrosion (CoRE-C), Research Institute, King Fahd University of Petroleum and Minerals, P.O. Box 1073, Dhahran 31261 (Saudi Arabia)

2011-09-01

The surface of carbon steel was modified by electrochemical deposition of Ni in a standard Watt's bath using dc and pulse plating electrodeposition. The aim was to compare the microstructure and surface mechanical properties of the deposit obtained by both techniques. Materials characterization was conducted using field emission scanning electron microscope fitted with scanning transmission electron detector, atomic force microscope and X-ray diffractometer. Nanoindentation hardness, elastic modulus, adhesion, coefficients of friction and wear rates were determined for both dc and pulse electrodeposits. Experimental results indicate that pulse electrodeposition produced finer Ni grains compared to dc plating. Size of Ni grains increased with deposition. Both dc and pulse deposition resulted in grain growth in preferred (2 0 0) orientation. However, presence of Ni (1 1 1) grains increased in deposits produced by pulse deposition. Pulse plated Ni exhibited higher hardness, creep and coefficient of friction and lower modulus of elasticity compared to dc plated Ni.

Effect of Processing Steps on the Mechanical Properties and Surface Appearance of 6063 Aluminium Extruded Products

Science.gov (United States)

Asensio-Lozano, Juan; Suárez-Peña, Beatriz; Vander Voort, George F.

2014-01-01

6063 aluminum anodized extrusions may exhibit a common surface defect known as streaking, characterized by the formation of narrow bands with a surface gloss different from the surrounding material. The origin of this banding lies in the differential surface topography produced after etching during the anodizing stage, shown to be connected to certain microstructural characteristics. The present study has attempted to determine the origin of these defects and measure the mechanical properties in these zones, properties which were either barely acceptable or did not meet the specification’s requirements. Quantitative metallography and mechanical testing, both tensile and microhardness, were used for materials assessment at the different steps of the process of manufacturing 6063 anodized extrusions. The results of this research show that nonequilibrium solidification rates during billet casting could lead to the formation of coarse eutectic Mg2Si particles which have a deleterious effect on both mechanical properties and surface appearance in the anodized condition. However, differences in the size and density of the coarse Mg2Si particles have been found to exist in the streak profile compared to the surrounding zones. The study revealed the importance of these particles in explaining the origin of the marginal or sub-marginal properties and anodizing surface defects found. PMID:28788673

Effect of Processing Steps on the Mechanical Properties and Surface Appearance of 6063 Aluminium Extruded Products

Directory of Open Access Journals (Sweden)

Juan Asensio-Lozano

2014-05-01

Full Text Available 6063 aluminum anodized extrusions may exhibit a common surface defect known as streaking, characterized by the formation of narrow bands with a surface gloss different from the surrounding material. The origin of this banding lies in the differential surface topography produced after etching during the anodizing stage, shown to be connected to certain microstructural characteristics. The present study has attempted to determine the origin of these defects and measure the mechanical properties in these zones, properties which were either barely acceptable or did not meet the specification’s requirements. Quantitative metallography and mechanical testing, both tensile and microhardness, were used for materials assessment at the different steps of the process of manufacturing 6063 anodized extrusions. The results of this research show that nonequilibrium solidification rates during billet casting could lead to the formation of coarse eutectic Mg2Si particles which have a deleterious effect on both mechanical properties and surface appearance in the anodized condition. However, differences in the size and density of the coarse Mg2Si particles have been found to exist in the streak profile compared to the surrounding zones. The study revealed the importance of these particles in explaining the origin of the marginal or sub-marginal properties and anodizing surface defects found.

Azobenzene as a photoregulator covalently attached to RNA: a quantum mechanics/molecular mechanics-surface hopping dynamics study.

Science.gov (United States)

Mondal, Padmabati; Granucci, Giovanni; Rastädter, Dominique; Persico, Maurizio; Burghardt, Irene

2018-05-28

The photoregulation of nucleic acids by azobenzene photoswitches has recently attracted considerable interest in the context of emerging biotechnological applications. To understand the mechanism of photoinduced isomerisation and conformational control in these complex biological environments, we employ a Quantum Mechanics/Molecular Mechanics (QM/MM) approach in conjunction with nonadiabatic Surface Hopping (SH) dynamics. Two representative RNA-azobenzene complexes are investigated, both of which contain the azobenzene chromophore covalently attached to an RNA double strand via a β-deoxyribose linker. Due to the pronounced constraints of the local RNA environment, it is found that trans -to- cis isomerization is slowed down to a time scale of ∼10-15 picoseconds, in contrast to 500 femtoseconds in vacuo , with a quantum yield reduced by a factor of two. By contrast, cis -to- trans isomerization remains in a sub-picosecond regime. A volume-conserving isomerization mechanism is found, similarly to the pedal-like mechanism previously identified for azobenzene in solution phase. Strikingly, the chiral RNA environment induces opposite right-handed and left-handed helicities of the ground-state cis -azobenzene chromophore in the two RNA-azobenzene complexes, along with an almost completely chirality conserving photochemical pathway for these helical enantiomers.

Middle school students' learning of mechanics concepts through engagement in different sequences of physical and virtual experiments

Science.gov (United States)

Sullivan, Sarah; Gnesdilow, Dana; Puntambekar, Sadhana; Kim, Jee-Seon

2017-08-01

Physical and virtual experimentation are thought to have different affordances for supporting students' learning. Research investigating the use of physical and virtual experiments to support students' learning has identified a variety of, sometimes conflicting, outcomes. Unanswered questions remain about how physical and virtual experiments may impact students' learning and for which contexts and content areas they may be most effective. Using a quasi-experimental design, we examined eighth grade students' (N = 100) learning of physics concepts related to pulleys depending on the sequence of physical and virtual labs they engaged in. Five classes of students were assigned to either the: physical first condition (PF) (n = 55), where students performed a physical pulley experiment and then performed the same experiment virtually, or virtual first condition (VF) (n = 45), with the opposite sequence. Repeated measures ANOVA's were conducted to examine how physical and virtual labs impacted students' learning of specific physics concepts. While we did not find clear-cut support that one sequence was better, we did find evidence that participating in virtual experiments may be more beneficial for learning certain physics concepts, such as work and mechanical advantage. Our findings support the idea that if time or physical materials are limited, using virtual experiments may help students understand work and mechanical advantage.

Mechanical Q-factor measurements on a test mass with a structured surface

Energy Technology Data Exchange (ETDEWEB)

Nawrodt, R [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Zimmer, A [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Koettig, T [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Clausnitzer, T [Institut fuer Angewandte Physik, Friedrich-Schiller-Universitaet Jena, Max-Wien-Platz 1, D-07743 Jena (Germany); Bunkowski, A [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Institut fuer Gravitationsphysik, Leibniz Universitaet Hannover, Callinstr. 38, D-30167 Hannover (Germany); Kley, E B [Institut fuer Angewandte Physik, Friedrich-Schiller-Universitaet Jena, Max-Wien-Platz 1, D-07743 Jena (Germany); Schnabel, R [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Institut fuer Gravitationsphysik, Leibniz Universitaet Hannover, Callinstr. 38, D-30167 Hannover (Germany); Danzmann, K [Max-Planck-Institut fuer Gravitationsphysik (Albert-Einstein-Institut) and Institut fuer Gravitationsphysik, Leibniz Universitaet Hannover, Callinstr. 38, D-30167 Hannover (Germany); Nietzsche, S [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Vodel, W [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany); Tuennermann, A [Institut fuer Angewandte Physik, Friedrich-Schiller-Universitaet Jena, Max-Wien-Platz 1, D-07743 Jena (Germany); Seidel, P [Institut fuer Festkoerperphysik, Friedrich-Schiller-Universitaet Jena, Helmholtzweg 5, D-07743 Jena (Germany)

2007-07-15

We present mechanical Q-factors (quality factors) of a crystalline quartz test mass with a nano-structured surface, measured in the temperature regime from 5 to 300 K. The nano-structure was a grating with a period of 2 {mu}m and a depth of about 0.1 {mu}m. Comparative measurements were performed on the plain substrate and on the structured test mass with different numbers of SiO{sub 2}/Ta{sub 2}O{sub 5} coating layers. The measurements at different stages of the test mass fabrication process show that the surface distortion induced by the nanostructure does not severely lower the mechanical Q-factor of the substrate. Damping due to a multi-layer coating stack was found to be orders of magnitude higher. The results provide vital information concerning the potential usage of low-thermal noise nano-structured test masses in future generations of high-precision laser interferometers and in current attempts to measure quantum effects of macroscopic mirror oscillators.

Mechanical properties of ceramic structures based on Triply Periodic Minimal Surface (TPMS) processed by 3D printing

Science.gov (United States)

Restrepo, S.; Ocampo, S.; Ramírez, J. A.; Paucar, C.; García, C.

2017-12-01

Repairing tissues and organs has been the main goal of surgical procedures. Since the 1990s, the main goal of tissue engineering has been reparation, using porous scaffolds that serve as a three-dimensional template for the initial fixation of cells and subsequent tissue formation both in vitro and in vivo. A scaffold must have specific characteristics of porosity, interconnectivity, surface area, pore volume, surface tortuosity, permeability and mechanical properties, which makes its design, manufacturing and characterization a complex process. Inspired by nature, triply periodic minimal surfaces (TPMS) have emerged as an alternative for the manufacture of porous pieces with design requirements, such as scaffolds for tissue repair. In the present work, we used the technique of 3D printing to obtain ceramic structures with Gyroid, Schwarz Primitive and Schwarz Diamond Surfaces shapes, three TPMS that fulfil the geometric requirements of a bone tissue scaffold. The main objective of this work is to compare the mechanical properties of ceramic pieces of three different forms of TPMS printed in 3D using a commercial ceramic paste. In this way it will be possible to clarify which is the TPMS with appropriate characteristics to construct scaffolds of ceramic materials for bone repair. A dependence of the mechanical properties with the geometry was found being the Primitive Surface which shows the highest mechanical properties.

The coupling of mechanical dynamics and induced currents in plates and surfaces

International Nuclear Information System (INIS)

Weissenburger, D.W.; Bialek, J.M.

1986-10-01

Significant mechanical reactions and deflections may be produced when electrical eddy currents induced in a conducting structure by transformer-like electromotive forces interact with background magnetic fields. Additional eddy currents induced by structural motion through the background fields modify both the mechanical and electrical dynamic behavior of the system. The observed effects of these motional eddy currents are sometimes referred to as magnetic damping and magnetic stiffness. This paper addresses the coupled structural deformation and eddy currents in flat plates and simple two-dimensional surfaces in three-space. A coupled system of equations has been formulated using finite element techniques for the mechanical aspects and a mesh network method for the electrical aspects of the problem

Physical and mechanical properties of spinach for whole-surface online imaging inspection

Science.gov (United States)

Tang, Xiuying; Mo, Chang Y.; Chan, Diane E.; Peng, Yankun; Qin, Jianwei; Yang, Chun-Chieh; Kim, Moon S.; Chao, Kuanglin

2011-06-01

The physical and mechanical properties of baby spinach were investigated, including density, Young's modulus, fracture strength, and friction coefficient. The average apparent density of baby spinach leaves was 0.5666 g/mm3. The tensile tests were performed using parallel, perpendicular, and diagonal directions with respect to the midrib of each leaf. The test results showed that the mechanical properties of spinach are anisotropic. For the parallel, diagonal, and perpendicular test directions, the average values for the Young's modulus values were found to be 2.137MPa, 1.0841 MPa, and 0.3914 MPa, respectively, and the average fracture strength values were 0.2429 MPa, 0.1396 MPa, and 0.1113 MPa, respectively. The static and kinetic friction coefficient between the baby spinach and conveyor belt were researched, whose test results showed that the average coefficients of kinetic and maximum static friction between the adaxial (front side) spinach leaf surface and conveyor belt were 1.2737 and 1.3635, respectively, and between the abaxial (back side) spinach leaf surface and conveyor belt were 1.1780 and 1.2451 respectively. These works provide the basis for future development of a whole-surface online imaging inspection system that can be used by the commercial vegetable processing industry to reduce food safety risks.

Measuring Engagement in Fourth to Twelfth Grade Classrooms: The Classroom Engagement Inventory

Science.gov (United States)

Wang, Ze; Bergin, Christi; Bergin, David A.

2014-01-01

Research on factors that may promote engagement is hampered by the absence of a measure of classroom-level engagement. Literature has suggested that engagement may have 3 dimensions--affective, behavioral, and cognitive. No existing engagement scales measure all 3 dimensions at the classroom level. The Classroom Engagement Inventory (CEI) was…

Stakeholder engagement and knowledge exchange in environmental research.

Science.gov (United States)

Phillipson, Jeremy; Lowe, Philip; Proctor, Amy; Ruto, Eric

2012-03-01

It is commonly put forward that effective uptake of research in policy or practice must be built upon a foundation of active knowledge exchange and stakeholder engagement during the research. However, what is often lacking is a systematic appreciation of the specific practices of knowledge exchange and their relative merits. The paper reports on a 2009 survey of 21 research projects within the UK Research Councils' Rural Economy and Land Use Programme regarding the involvement and perceived impact of over a thousand stakeholders in the research. The survey reveals that most stakeholders were involved as research subjects or as event participants. Large numbers were also engaged in the research process itself, including involvement in shaping the direction of research. Stakeholder engagement is perceived as bringing significant benefits to the process of knowledge production. A close relationship is found between mechanisms and approaches to knowledge exchange and the spread of benefits for researchers and stakeholders. Mutual benefits are gained from exchange of staff or where stakeholders are members of research advisory groups. Different stakeholder sectors are also associated with different patterns of engagement, which lead to contrasting impact patterns. Any efforts to alter knowledge exchange processes and outcomes must overcome these differing engagement tendencies. Overall, much greater attention should be given to early processes of knowledge exchange and stakeholder engagement within the lifetime of research projects. Copyright © 2011 Elsevier Ltd. All rights reserved.

Early stages of Cs adsorption mechanism for GaAs nanowire surface

Science.gov (United States)

Diao, Yu; Liu, Lei; Xia, Sihao; Feng, Shu

2018-03-01

In this study, the adsorption mechanism of Cs adatoms on the (100) surface of GaAs nanowire with [0001] growth direction is investigated utilizing first principles method based on density function theory. The adsorption energy, work function, atomic structure and electronic property of clean surface and Cs-covered surfaces with different coverage are discussed. Results show that when only one Cs is adsorbed on the surface, the most favorable adsorption site is BGa-As. With increasing Cs coverage, work function gradually decreases and gets its minimum at 0.75 ML, then rises slightly when Cs coverage comes to 1 ML, indicating the existence of 'Cs-kill' phenomenon. According to further analysis, Cs activation process can effectively reduce the work function due to the formation of a downward band bending region and surface dipole moment directing from Cs adatom to the surface. As Cs coverage increases, the conduction band minimum and valence band maximum both shift towards lower energy side, contributed by the orbital hybridization between Cs-5s, Cs-5p states and Ga-4p, As-4s, As-4p states near Fermi level. The theoretical calculations and analysis in this study can improve the Cs activation technology for negative electron affinity optoelectronic devices based on GaAs nanowires, and also provide a reference for the further Cs/O or Cs/NF3 activation process.

Correlation between the wear behaviour and the mechanical properties of several surface treatments

International Nuclear Information System (INIS)

Lelait, L.; Lina, A.; Rezakhanlou, R.; Duysen, J.C. van; Stebut, J. von

1993-01-01

Surface mechanical strength of chromium base (electrolytic and plasma sprayed) coatings is studied for friction and wear applications in nuclear environment. Indentation, scratch, and wear testing results are compared. In particular intrinsic coating brittleness is investigated as a mechanism responsible for impact wear. Electrolytic, hard chromium plate has a wear resistance well below that of the spray coated specimens studied. Acoustic emission level and brittle damage features are shown to be correlated. (orig.)

Student Engagement in the Scottish Quality Enhancement Framework

Science.gov (United States)

Gvaramadze, Irakli

2011-01-01

The research addressed the interplay of student engagement and quality enhancement mechanisms in the Scottish higher education system. The paper demonstrates increasing focus on student learning, learning experience and high-quality learning in the current quality enhancement approaches. The student-university coproduction model is used to…

On fatigue crack growth mechanisms of MMC: Reflection on analysis of 'multi surface initiations'

International Nuclear Information System (INIS)

Mkaddem, A.; El Mansori, M.

2009-01-01

This work attempts to examine the mechanisms of fatigue when cracks synergetically initiate in more than one site at the specimen surface. The metal matrix composites (MMC) i.e. silicon carbide particles reinforced aluminium matrix composites (Al/SiC p -MMC), seem to be good candidates to accelerate fatigue failures following multi surface initiations (MSI). Closure effects of MSI mechanisms on the variation of fatigue behaviour are explored for various stress states. Experiments were carried out using non pre-treated and pre-treated specimens. Using an Equivalent Ellipse Method (EEM), it is shown that the aspect of surface finish of specimen plays an important role on crack growth. Scanning Electron Microscope (SEM) inspections have lead to distinguishing the initiation regions from propagation regions and final separation regions. It is also revealed that the total lifetime of specimens is sensitive to heat treatment. Moreover, it is found that the appearance of MSI in cycled materials is more probable at high level of fatigue loads.

Surface transport mechanisms in molecular glasses probed by the exposure of nano-particles

Science.gov (United States)

Ruan, Shigang; Musumeci, Daniele; Zhang, Wei; Gujral, Ankit; Ediger, M. D.; Yu, Lian

2017-05-01

For a glass-forming liquid, the mechanism by which its surface contour evolves can change from bulk viscous flow at high temperatures to surface diffusion at low temperatures. We show that this mechanistic change can be conveniently detected by the exposure of nano-particles native in the material. Despite its high chemical purity, the often-studied molecular glass indomethacin contains low-concentration particles approximately 100 nm in size and 0.3% in volume fraction. Similar particles are present in polystyrene, another often-used model. In the surface-diffusion regime, particles are gradually exposed in regions vacated by host molecules, for example, the peak of a surface grating and the depletion zone near a surface crystal. In the viscous-flow regime, particle exposure is not observed. The surface contour around an exposed particle widens over time in a self-similar manner as 3 (Bt)1/4, where B is a surface mobility constant and the same constant obtained by surface grating decay. This work suggests that in a binary system composed of slow- and fast-diffusing molecules, slow-diffusing molecules can be stranded in surface regions vacated by fast-diffusing molecules, effectively leading to phase separation.

Insights into the activation mechanism of calcium ions on the sericite surface: A combined experimental and computational study

Science.gov (United States)

Hu, Yuehua; He, Jianyong; Zhang, Chenhu; Zhang, Chenyang; Sun, Wei; Zhao, Dongbo; Chen, Pan; Han, Haisheng; Gao, Zhiyong; Liu, Runqing; Wang, Li

2018-01-01

The adsorption behaviors and the activation mechanism of calcium ions (Ca2+) on sericite surface have been investigated by Zeta potential measurements, Fourier transform infrared spectroscopy (FT-IR), Micro-flotation tests and First principle calculations. Zeta potential tests results show that the sericite surface potential increases due to the adsorption of calcium ions on the surface. Micro-flotation tests demonstrate that sericite recovery remarkably rise by 10% due to the calcium ions activation on sericite surface. However, the characteristic adsorption bands of calcium oleate do not appear in the FT-IR spectrum, suggesting that oleate ions just physically adsorb on the sericite surface. The first principle calculations based on the density functional theory (DFT) further reveals the microscopic adsorption mechanism of calcium ions on the sericite surface before and after hydration.

Role of surface on the size-dependent mechanical properties of copper nanowire under tensile load: A molecular dynamics simulation

International Nuclear Information System (INIS)

Liu, Wei-Ting; Hsiao, Chun-I.; Hsu, Wen-Dung

2014-01-01

In this study we have used atomistic simulations to investigate the role of surface on the size-dependent mechanical properties of nanowires. In particular, we have performed computational investigation on single crystal face-centered cubic copper nano-wires with diameters ranging from 2 to 20 nm. The wire axis for all the nanowires are considered along the [0 0 1] direction. Characterization of the initial optimized structures revealed clear differences in interatomic spacing, stress, and potential energy in all the nanowires. The mechanical properties with respect to wire diameter are evaluated by applying tension along the [0 0 1] direction until yielding. We have discussed the stress–strain relationships, Young's modulus, and the variation in potential energy from surface to the center of the wire for all the cases. Our results indicate that the mechanical response (including yield strain, Young's modulus, and resilience) is directly related to the proportion of surface to bulk type atoms present in each nanowire. Thus the size-dependent mechanical properties of single crystal copper nanowire within elastic region are attributed to the surface to volume ratio (surface effect). Using the calculated response, we have formulated a mathematical relationship, which predicts the nonlinear correlation between the mechanical properties and the diameter of the wire.

Role of surface on the size-dependent mechanical properties of copper nanowire under tensile load: A molecular dynamics simulation

Energy Technology Data Exchange (ETDEWEB)

Liu, Wei-Ting [Department of Materials Science and Engineering, National Cheng Kung University, Tainan City 70101 Taiwan (China); Hsiao, Chun-I. [Department of Materials Science and Engineering, National Cheng Kung University, Tainan City 70101 Taiwan (China); Promotion Center for Global Materials Research, National Cheng Kung University, Tainan City 70101 Taiwan (China); Hsu, Wen-Dung, E-mail: wendung@mail.ncku.edu.tw [Department of Materials Science and Engineering, National Cheng Kung University, Tainan City 70101 Taiwan (China); Research Center for Energy Technology and Strategy, National Cheng Kung University, Tainan City 70101 Taiwan (China); Promotion Center for Global Materials Research, National Cheng Kung University, Tainan City 70101 Taiwan (China)

2014-01-15

In this study we have used atomistic simulations to investigate the role of surface on the size-dependent mechanical properties of nanowires. In particular, we have performed computational investigation on single crystal face-centered cubic copper nano-wires with diameters ranging from 2 to 20 nm. The wire axis for all the nanowires are considered along the [0 0 1] direction. Characterization of the initial optimized structures revealed clear differences in interatomic spacing, stress, and potential energy in all the nanowires. The mechanical properties with respect to wire diameter are evaluated by applying tension along the [0 0 1] direction until yielding. We have discussed the stress–strain relationships, Young's modulus, and the variation in potential energy from surface to the center of the wire for all the cases. Our results indicate that the mechanical response (including yield strain, Young's modulus, and resilience) is directly related to the proportion of surface to bulk type atoms present in each nanowire. Thus the size-dependent mechanical properties of single crystal copper nanowire within elastic region are attributed to the surface to volume ratio (surface effect). Using the calculated response, we have formulated a mathematical relationship, which predicts the nonlinear correlation between the mechanical properties and the diameter of the wire.

Oxidation and metal-insertion in molybdenite surfaces: evaluation of charge-transfer mechanisms and dynamics

Directory of Open Access Journals (Sweden)

Shutthanandan V

2008-06-01

Full Text Available Abstract Molybdenum disulfide (MoS2, a layered transition-metal dichalcogenide, has been of special importance to the research community of geochemistry, materials and environmental chemistry, and geotechnical engineering. Understanding the oxidation behavior and charge-transfer mechanisms in MoS2 is important to gain better insight into the degradation of this mineral in the environment. In addition, understanding the insertion of metals into molybdenite and evaluation of charge-transfer mechanism and dynamics is important to utilize these minerals in technological applications. Furthermore, a detailed investigation of thermal oxidation behavior and metal-insertion will provide a basis to further explore and model the mechanism of adsorption of metal ions onto geomedia. The present work was performed to understand thermal oxidation and metal-insertion processes of molybdenite surfaces. The analysis was performed using atomic force microscopy (AFM, scanning electron microscopy (SEM, transmission electron microscopy (TEM, Rutherford backscattering spectrometry (RBS, and nuclear reaction analysis (NRA. Structural studies using SEM and TEM indicate the local-disordering of the structure as a result of charge-transfer process between the inserted lithium and the molybdenite layer. Selected area electron diffraction measurements indicate the large variations in the diffusivity of lithium confirming that the charge-transfer is different along and perpendicular to the layers in molybdenite. Thermal heating of molybenite surface in air at 400°C induces surface oxidation, which is slow during the first hour of heating and then increases significantly. The SEM results indicate that the crystals formed on the molybdenite surface as a result of thermal oxidation exhibit regular thin-elongated shape. The average size and density of the crystals on the surface is dependent on the time of annealing; smaller size and high density during the first one-hour and

Oxidation and metal-insertion in molybdenite surfaces: evaluation of charge-transfer mechanisms and dynamics.

Science.gov (United States)

Ramana, C V; Becker, U; Shutthanandan, V; Julien, C M

2008-06-05

Molybdenum disulfide (MoS2), a layered transition-metal dichalcogenide, has been of special importance to the research community of geochemistry, materials and environmental chemistry, and geotechnical engineering. Understanding the oxidation behavior and charge-transfer mechanisms in MoS2 is important to gain better insight into the degradation of this mineral in the environment. In addition, understanding the insertion of metals into molybdenite and evaluation of charge-transfer mechanism and dynamics is important to utilize these minerals in technological applications. Furthermore, a detailed investigation of thermal oxidation behavior and metal-insertion will provide a basis to further explore and model the mechanism of adsorption of metal ions onto geomedia.The present work was performed to understand thermal oxidation and metal-insertion processes of molybdenite surfaces. The analysis was performed using atomic force microscopy (AFM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Rutherford backscattering spectrometry (RBS), and nuclear reaction analysis (NRA).Structural studies using SEM and TEM indicate the local-disordering of the structure as a result of charge-transfer process between the inserted lithium and the molybdenite layer. Selected area electron diffraction measurements indicate the large variations in the diffusivity of lithium confirming that the charge-transfer is different along and perpendicular to the layers in molybdenite. Thermal heating of molybenite surface in air at 400 degrees C induces surface oxidation, which is slow during the first hour of heating and then increases significantly. The SEM results indicate that the crystals formed on the molybdenite surface as a result of thermal oxidation exhibit regular thin-elongated shape. The average size and density of the crystals on the surface is dependent on the time of annealing; smaller size and high density during the first one-hour and significant

Modification of the iron mechanical- and corrosion features by ion implantation in surface

International Nuclear Information System (INIS)

Baumvol, I.J.R.

1981-01-01

The physical mechanisms responsable by the tin ion implantation in the iron surface at moderated doses are studied. Several techniques are used such as alpha-particle Rutherford backscattering, conversion electron Moessbauer spectroscopy and scanning electron microscopy. (L.C.) [pt

A comparative investigation of bone surface after cutting with mechanical tools and Er:YAG laser.

Science.gov (United States)

Baek, Kyung-Won; Deibel, Waldemar; Marinov, Dilyan; Griessen, Mathias; Dard, Michel; Bruno, Alfredo; Zeilhofer, Hans-Florian; Cattin, Philippe; Juergens, Philipp

2015-07-01

Despite of the long history of medical application, laser ablation of bone tissue became successful only recently. Laser bone cutting is proven to have higher accuracy and to increase bone healing compared to conventional mechanical bone cutting. But the reason of subsequent better healing is not biologically explained yet. In this study we present our experience with an integrated miniaturized laser system mounted on a surgical lightweight robotic arm. An Erbium-doped Yttrium Aluminium Garnet (Er:YAG) laser and a piezoelectric (PZE) osteotome were used for comparison. In six grown up female Göttingen minipigs, comparative surgical interventions were done on the edentulous mandibular ridge. Our laser system was used to create different shapes of bone defects on the left side of the mandible. On the contralateral side, similar bone defects were created by PZE osteotome. Small bone samples were harvested to compare the immediate post-operative cut surface. The analysis of the cut surface of the laser osteotomy and conventional mechanical osteotomy revealed an essential difference. The scanning electron microscopy (SEM) analysis showed biologically open cut surfaces from the laser osteotomy. The samples from PZE osteotomy showed a flattened tissue structure over the cut surface, resembling the "smear layer" from tooth preparation. We concluded that our new finding with the mechanical osteotomy suggests a biological explanation to the expected difference in subsequent bone healing. Our hypothesis is that the difference of surface characteristic yields to different bleeding pattern and subsequently results in different bone healing. The analyses of bone healing will support our hypothesis. © 2015 Wiley Periodicals, Inc.

Modifications of mechanical characteristics and iron corrosion by ionic implantation on surface

International Nuclear Information System (INIS)

Baumvol, I.J.

1980-01-01

Tin ionic implantation on pure iron surface at moderate doses (5x10 15 to 5x10 16 ) Sn + Cu -2 ) has proven to be very efficient in improving the metal characteristics to oxidation and abrasion at high temperature. The abrasion volumetric coefficient K v , is reduced from up to 100 times, and the oxidation tax constant is reduced from up to 10 times. The physical mechanisms responsible for these phenomena are studied using different techniques of surface analysis; as Rutherford backscattering of alpha particles, Moessbauer spectroscopy of conversion electrons and sweeping electronic microscopy. (A.C.A.S.) [pt

Damage Mechanism in Counter Pairs Caused by Bionic Non-smoothed Surface

Directory of Open Access Journals (Sweden)

ZHANG Zhan-hui

2016-08-01

Full Text Available Four biomimetic non-smoothed surface specimens with different shapes were prepared by laser processing. Tests were conducted on MMU-5G wear and abrasion test machine to study the influencing rule of non-smoothed surfaces on counter pairs. The results show that the mass loss of the friction pair matching with the non-smoothed units is much greater than the ones matching with the smooth specimens. The pairs matching with different non-smoothed units suffer differently. The non-smoothed surface protruding zone exerts micro cutting on counter pairs. The striation causes the greatest mass loss of the pairs than the other non-smoothed units, which almost doubles the damage of the grid ones suffering the least. The difference in pairs damage is attributed to the different mechanism of undertaking the load in the process of wear. The damage can be alleviated effectively by changing the shapes of the units without increasing or decreasing the area ratio of the non-smoothed units.

Role of surfaces and interfaces in controlling the mechanical properties of metallic alloys.

Science.gov (United States)

Lee, Won-Jong; Chia, Wen-Jui; Wang, Jinliu; Chen, Yanfeng; Vaynman, Semyon; Fine, Morris E; Chung, Yip-Wah

2010-11-02

This article explores the subtle effects of surfaces and interfaces on the mechanical properties of bulk metallic alloys using three examples: environmental effects on fatigue life, hydrogen embrittlement effects on the ductility of intermetallics, and the role of coherent precipitates in the toughness of steels. It is demonstrated that the marked degradation of the fatigue life of metals is due to the strong chemisorption of adsorbates on exposed slip steps that are formed during fatigue deformation. These adsorbates reduce the reversibility of slip, thus accelerating fatigue damage in a chemically active gas environment. For certain intermetallic alloys such as Ni(3)Al and Ni(3)Fe, the ductility depends on the ambient gas composition and the atomic ordering in these alloys, both of which govern the complex surface chemical reactions taking place in the vicinity of crack tips. Finally, it is shown that local stresses at a coherent precipitate-matrix interface can activate dislocation motion at low temperatures, thus improving the fracture toughness of bulk alloys such as steels at cryogenic temperatures. These examples illustrate the complex interplay between surface chemistry and mechanics, often yielding unexpected results.

Experimental identification for physical mechanism of fiber-form nanostructure growth on metal surfaces with helium plasma irradiation

Energy Technology Data Exchange (ETDEWEB)

Takamura, S., E-mail: takamura@aitech.ac.jp [Faculty of Engineering, Aichi Institute of Technology, Yakusa-cho, Toyota 470-0392 (Japan); Uesugi, Y. [Faculty of Electrical and Computer Engineering, Institute of Science and Engineering, Kanazawa University, Kanazawa 920-1192 (Japan)

2015-11-30

Highlights: • Initial growth process of fiber-form nanostructure on metal surfaces under helium ion irradiation is given based on experimental knowledge, where the pitting of original surface and forming nano-walls and/or loop-like nanostructure works as precursors. • The physical mechanism of fiber growth is discussed in terms of shear modulus of metals influenced by helium content as well as surface temperature. • The physical model explains the reason why tantalum does not make sufficiently grown nano-fibers, and the temperature dependence of surface morphology of titanium. - Abstract: The initial stage of fiber-form nanostructure growth on metal surface with helium plasma irradiation is illustrated, taking recent research knowledge using a flux gradient technique, and including loop-like nano-scale structure as precursors. The growth mechanism of fibers is discussed in terms of the shear modulus of various materials that is influenced by the helium content as well as the surface temperature, and the mobility of helium atoms, clusters and/or nano-bubbles in the bulk, loops and fibers. This model may explain the reason why tantalum does not provide fiber-form nanostructure although the loop-like structure was identified. The model also suggests the mechanism of an existence of two kinds of nanostructure of titanium depending on surface temperature. Industrial applications of such nanostructures are suggested in the properties and the possibilities of its growth on other basic materials.

Spontaneous grafting of diazonium salts: chemical mechanism on metallic surfaces.

Science.gov (United States)

Mesnage, Alice; Lefèvre, Xavier; Jégou, Pascale; Deniau, Guy; Palacin, Serge

2012-08-14

The spontaneous reaction of diazonium salts on various substrates has been widely employed since it consists of a simple immersion of the substrate in the diazonium salt solution. As electrochemical processes involving the same diazonium salts, the spontaneous grafting is assumed to give covalently poly(phenylene)-like bonded films. Resistance to solvents and to ultrasonication is commonly accepted as indirect proof of the existence of a covalent bond. However, the most relevant attempts to demonstrate a metal-C interface bond have been obtained by an XPS investigation of spontaneously grafted films on copper. Similarly, our experiments give evidence of such a bond in spontaneously grafted films on nickel substrates in acetonitrile. In the case of gold substrates, the formation of a spontaneous film was unexpected but reported in the literature in parallel to our observations. Even if no interfacial bond was observed, formation of the films was explained by grafting of aryl cations or radicals on the surface arising from dediazoniation, the film growing later by azo coupling, radical addition, or cationic addition on the grafted phenyl layer. Nevertheless, none of these mechanisms fits our experimental results showing the presence of an Au-N bond. In this work, we present a fine spectroscopic analysis of the coatings obtained on gold and nickel substrates that allow us to propose a chemical structure of such films, in particular, their interface with the substrates. After testing the most probable mechanisms, we have concluded in favor of the involvement of two complementary mechanisms which are the direct reaction of diazonium salts with the gold surface that accounts for the observed Au-N interfacial bonds as well as the formation of aryl cations able to graft on the substrate through Au-C linkages.

Effect of surface decarburization on the mechanical properties of high strength low alloy steel

International Nuclear Information System (INIS)

Saqib, S.

1993-01-01

An attempt has been made to study the relationship of mechanical properties with the microstructure of a high strength low alloy steel. A thorough investigation was conducted on the steel sheet and variation in mechanical properties was observed across its thickness with a change in the microstructure. Change in hardness and tensile strength at the surface compare to the core of the material is attributed to decarburization. The current research indicates that the correlation between hardness and tensile strength is not valid for steels if the hardness is determined on the surface only. Great care should be taken at the time of determination of tensile strength by using conversion charts/tables on the basis of hardness values obtained by practical means. (author)

Mechanics of curved surfaces, with application to surface-parallel cracks

Science.gov (United States)

Martel, Stephen J.

2011-10-01

The surfaces of many bodies are weakened by shallow enigmatic cracks that parallel the surface. A re-formulation of the static equilibrium equations in a curvilinear reference frame shows that a tension perpendicular to a traction-free surface can arise at shallow depths even under the influence of gravity. This condition occurs if σ11k1 + σ22k2 > ρg cosβ, where k1 and k2 are the principal curvatures (negative if convex) at the surface, σ11 and σ22 are tensile (positive) or compressive (negative) stresses parallel to the respective principal curvature arcs, ρ is material density, g is gravitational acceleration, and β is the surface slope. The curvature terms do not appear in equilibrium equations in a Cartesian reference frame. Compression parallel to a convex surface thus can cause subsurface cracks to open. A quantitative test of the relationship above accounts for where sheeting joints (prominent shallow surface-parallel fractures in rock) are abundant and for where they are scarce or absent in the varied topography of Yosemite National Park, resolving key aspects of a classic problem in geology: the formation of sheeting joints. Moreover, since the equilibrium equations are independent of rheology, the relationship above can be applied to delamination or spalling caused by surface-parallel cracks in many materials.

Mechanical touch responses of Arabidopsis TCH1-3 mutant roots on inclined hard-agar surface

Science.gov (United States)

Zha, Guodong; Wang, Bochu; Liu, Junyu; Yan, Jie; Zhu, Liqing; Yang, Xingyan

2016-01-01

The gravity-induced mechanical touch stimulus can affect plant root architecture. Mechanical touch responses of plant roots are an important aspect of plant root growth and development. Previous studies have reported that Arabidopsis TCH1-3 genes are involved in mechano-related events, how-ever, the physiological functions of TCH1-3 genes in Arabidopsis root mechanoresponses remain unclear. In the present study, we applied an inclined hard agar plate method to produce mechanical touch stimulus, and provided evidence that altered mechanical environment could influence root growth. Furthermore, tch1-3 Arabidopsis mutants were investigated on inclined agar surfaces to explore the functions of TCH1-3 genes on Arabidopsis root mechanoresponses. The results showed that two tch2 mutants, cml24-2 and cml24-4, exhibited significantly reduced root length, biased skewing, and decreased density of lateral root. In addition, primary root length and density of lateral root of tch3 (cml12-2) was significantly decreased on inclined agar surfaces. This study indicates that the tch2 and tch3 mutants are hypersensitive to mechanical touch stimulus, and TCH2 (CML24-2 and CML24-4) and TCH3 (CML12-2) genes may participate in the mechanical touch response of Arabidopsis roots.

Surface mechanics design by cavitation peening

Directory of Open Access Journals (Sweden)

Hitoshi Soyama

2015-07-01

Full Text Available Although impacts at cavitation bubble collapses cause severe damage in hydraulic machineries, the cavitation impacts can be utilised for surface mechanics design such as introduction of compressive residual stress and/or improvement of fatigue strength. The peening method using the cavitation impacts was called as cavitation peening. In order to reveal the peening intensity of hydrodynamic cavitation and laser cavitation, the arc height of Almen strip and duralumin plate were measured. In the case of hydrodynamic cavitation, cavitation was generated by injecting a high speed water jet into water with a pressurised chamber and an open chamber, and the cavitating jet in air was also examined. The laser cavitation was produced by a pulse laser, and a high speed observation using a high speed video camera was carried out to clarify laser abrasion and laser cavitation with detecting noise by a hydrophone. It was concluded that the peening intensity by using the cavitating jet in water with the pressurized chamber was most aggressive, and the impact induced by the laser cavitation was larger than that of the laser abrasion at the present condition.

Governance and Citizens' Engagement in Terms of Local Sustainable Development

Directory of Open Access Journals (Sweden)

Agnieszka Sobol

2015-01-01

Full Text Available Local sustainable development emphasizes the role of a community. One of the key prerequisite of this process is therefore participation of inhabitants. Nevertheless traditional way of managing cities does not work very well in terms of public engagement. Local sustainable development requires both i.e. governance mechanisms introduced by the local authorities and positive reaction of inhabitants for the invitation for cooperation. The paper is intended to explore some critical issues and dimensions of governance and citizens' engagement in terms of local sustainable development. It shows the general outlook on the most relevant conditions, factors, problems and barriers of this process in Poland. It presents experiences of the city of Rybnik in its work towards public engagement in local development.

Objectives for Stakeholder Engagement in Global Environmental Assessments

Directory of Open Access Journals (Sweden)

Jennifer Garard

2017-09-01

Full Text Available Global environmental assessments (GEAs are among the most large-scale, formalized processes for synthesizing knowledge at the science–policy–society interface. The successful engagement of diverse stakeholders in GEAs is often described as a crucial mechanism for increasing their legitimacy, salience and credibility. However, the diversity of perspectives on the more precise objectives for stakeholder engagement remains largely unclear. The aims of this study are to categorize and characterize the diversity of perspectives on objectives for stakeholder engagement in GEAs; to explore differences in perspectives within and between different stakeholder groups and categories; and to test whether the more practical prioritization and selection of objectives in GEAs can be linked to deliberative policy learning as a higher-level rationale for stakeholder engagement. For these purposes, we conduct a grounded theory analysis and a keyword analysis of interview material and official GEA documents relating to two GEAs: UN Environment’s Fifth Global Environment Outlook and the Working Group III contribution to the Intergovernmental Panel on Climate Change Fifth Assessment Report. Based on the analysis, we identify six categories of objectives and present as hypotheses promising ways forward for prioritizing and characterizing objectives for stakeholder engagement in GEAs, as well as potential reasons for the differences between perspectives on objectives. This study draws attention to the need for future GEA processes to have more explicit discussions on the objectives for stakeholder engagement, as well as the importance of moving towards increasingly deliberative and inclusive assessment processes more broadly.

Study of multilayer packaging delamination mechanisms using different surface analysis techniques

Energy Technology Data Exchange (ETDEWEB)

Garrido-Lopez, Alvaro [Department of Chemistry, University of La Rioja, C/Madre de Dios 51, E-26006 Logrono, La Rioja (Spain); Tena, Maria Teresa, E-mail: maria-teresa.tena@unirioja.es [Department of Chemistry, University of La Rioja, C/Madre de Dios 51, E-26006 Logrono, La Rioja (Spain)

2010-04-01

Multilayer packaging, consisting of different layers joined by using an adhesive or an extrusion process, is widely used to promote different products, such as food, cosmetics, etc. The main disadvantage in using this form of packaging is the delamination process. In this work, different surface techniques (X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectroscopy and attenuated total reflection Fourier transform infrared spectroscopy) are used to analyse the delaminated surfaces in order to study the mechanisms that cause delamination of multilayer packaging. According to our results, the reaction of migrated molecules with adhesive-aluminium bonds is the main cause of the chemical delamination process. In contrast, the delamination of extruded materials would seem to be caused by the breaking of Van der Waals bonds.

A parametric study of surface roughness and bonding mechanisms of aluminum alloys with epoxies: a molecular dynamics simulation

Science.gov (United States)

Timilsina, Rajendra; Termaath, Stephanie

The marine environment is highly aggressive towards most materials. However, aluminium-magnesium alloys (Al-Mg, specifically, 5xxx series) have exceptionally long service life in such aggressive marine environments. For instance, an Al-Mg alloy, AA5083, is extensively used in naval structures because of its good mechanical strength, formability, seawater corrosion resistance and weldability. However, bonding mechanisms of these alloys with epoxies in a rough surface environment are not fully understood yet. It requires a rigorous investigation at molecular or atomic levels. We performed a molecular dynamics simulation to study an adherend surface preparation and surface bonding mechanisms of Al-Mg alloy (AA5083) with different epoxies by developing several computer models. Various distributions of surface roughness are introduced in the models and performed molecular dynamics simulations. Formation of a beta phase (Al3Mg2) , microstructures, bonding energies at the interface, bonding strengths and durability are investigated. Office of Naval Research.

Synoptic-scale analysis of mechanisms driving surface chlorophyll dynamics in the North Atlantic

DEFF Research Database (Denmark)

Ferreira, Ana Sofia; Hatun, H.; Counillon, F.

2015-01-01

show that, in terms of bottom-up processes alone, there is a dominant physical mechanism, namely mixed-layer shoaling, that best predicts the interannual variation in the initial increase in surface chlorophyll across large sectors of the North Atlantic. We further show that different regions...

The ECOUTER methodology for stakeholder engagement in translational research.

Science.gov (United States)

Murtagh, Madeleine J; Minion, Joel T; Turner, Andrew; Wilson, Rebecca C; Blell, Mwenza; Ochieng, Cynthia; Murtagh, Barnaby; Roberts, Stephanie; Butters, Oliver W; Burton, Paul R

2017-04-04

Because no single person or group holds knowledge about all aspects of research, mechanisms are needed to support knowledge exchange and engagement. Expertise in the research setting necessarily includes scientific and methodological expertise, but also expertise gained through the experience of participating in research and/or being a recipient of research outcomes (as a patient or member of the public). Engagement is, by its nature, reciprocal and relational: the process of engaging research participants, patients, citizens and others (the many 'publics' of engagement) brings them closer to the research but also brings the research closer to them. When translating research into practice, engaging the public and other stakeholders is explicitly intended to make the outcomes of translation relevant to its constituency of users. In practice, engagement faces numerous challenges and is often time-consuming, expensive and 'thorny' work. We explore the epistemic and ontological considerations and implications of four common critiques of engagement methodologies that contest: representativeness, communication and articulation, impacts and outcome, and democracy. The ECOUTER (Employing COnceptUal schema for policy and Translation Engagement in Research) methodology addresses problems of representation and epistemic foundationalism using a methodology that asks, "How could it be otherwise?" ECOUTER affords the possibility of engagement where spatial and temporal constraints are present, relying on saturation as a method of 'keeping open' the possible considerations that might emerge and including reflexive use of qualitative analytic methods. This paper describes the ECOUTER process, focusing on one worked example and detailing lessons learned from four other pilots. ECOUTER uses mind-mapping techniques to 'open up' engagement, iteratively and organically. ECOUTER aims to balance the breadth, accessibility and user-determination of the scope of engagement. An ECOUTER

A computer vision system for rapid search inspired by surface-based attention mechanisms from human perception.

Science.gov (United States)

Mohr, Johannes; Park, Jong-Han; Obermayer, Klaus

2014-12-01

Humans are highly efficient at visual search tasks by focusing selective attention on a small but relevant region of a visual scene. Recent results from biological vision suggest that surfaces of distinct physical objects form the basic units of this attentional process. The aim of this paper is to demonstrate how such surface-based attention mechanisms can speed up a computer vision system for visual search. The system uses fast perceptual grouping of depth cues to represent the visual world at the level of surfaces. This representation is stored in short-term memory and updated over time. A top-down guided attention mechanism sequentially selects one of the surfaces for detailed inspection by a recognition module. We show that the proposed attention framework requires little computational overhead (about 11 ms), but enables the system to operate in real-time and leads to a substantial increase in search efficiency. Copyright © 2014 Elsevier Ltd. All rights reserved.

Biaxially mechanical tuning of 2-D reversible and irreversible surface topologies through simultaneous and sequential wrinkling.

Science.gov (United States)

Yin, Jie; Yagüe, Jose Luis; Boyce, Mary C; Gleason, Karen K

2014-02-26

Controlled buckling is a facile means of structuring surfaces. The resulting ordered wrinkling topologies provide surface properties and features desired for multifunctional applications. Here, we study the biaxially dynamic tuning of two-dimensional wrinkled micropatterns under cyclic mechanical stretching/releasing/restretching simultaneously or sequentially. A biaxially prestretched PDMS substrate is coated with a stiff polymer deposited by initiated chemical vapor deposition (iCVD). Applying a mechanical release/restretch cycle in two directions loaded simultaneously or sequentially to the wrinkled system results in a variety of dynamic and tunable wrinkled geometries, the evolution of which is investigated using in situ optical profilometry, numerical simulations, and theoretical modeling. Results show that restretching ordered herringbone micropatterns, created through sequential release of biaxial prestrain, leads to reversible and repeatable surface topography. The initial flat surface and the same wrinkled herringbone pattern are obtained alternatively after cyclic release/restretch processes, owing to the highly ordered structure leaving no avenue for trapping irregular topological regions during cycling as further evidenced by the uniformity of strains distributions and negligible residual strain. Conversely, restretching disordered labyrinth micropatterns created through simultaneous release shows an irreversible surface topology whether after sequential or simultaneous restretching due to creation of irregular surface topologies with regions of highly concentrated strain upon formation of the labyrinth which then lead to residual strains and trapped topologies upon cycling; furthermore, these trapped topologies depend upon the subsequent strain histories as well as the cycle. The disordered labyrinth pattern varies after each cyclic release/restretch process, presenting residual shallow patterns instead of achieving a flat state. The ability to

Effects of Surface Modification of MWCNT on the Mechanical and Electrical Properties of Fluoro Elastomer/MWCNT Nanocomposites

Directory of Open Access Journals (Sweden)

Tao Xu

2012-01-01

Full Text Available Surface modification is a good way to improve the surface activity and interfacial strength of multiwalled carbon nanotubes (MWCNTs when used as fillers in the polymer composites. Among the reported methods for nanotube modification, mixed acid oxidation and plasma treatment is often used by introducing polar groups to the sidewall of MWCNT successfully. The purpose of this study is to evaluate the effect of different surface modification of MWCNT on the mechanical property and electrical conductivity of Fluoro-elastomer (FE/MWCNT nanocomposites. MWCNTs were surface modified by mixed oxidation and CF4 plasma treatment and then used to reinforce the fluoro elastomer (FE, a copolymer of trifluorochloroethylene and polyvinylidene fluoride. FE/MWCNT composite films were prepared from mixture solutions of ethylacetate and butylacetate, using untreated CNTs (UCNTs, acid-modified CNTs (ACNTs, and CF4 plasma-modified CNT (FCNTs. In each case, MWCNT content was 0.01 wt%, 0.05 wt%, 0.1 wt%, and 0.2 wt% with respect to the polymer. Morphology and mechanical properties were characterized by using scanning electron microscopy (SEM, Raman spectroscopy, as well as dynamic mechanical tests. The SEM results indicated that dispersion of ACNTs and especially FCNTs in FE was better than that of UCNTs. DMA indicated mechanical properties of FCNT composites were improved over ACNT and UCNT filled FE. The resulting electrical properties of the composites ranged from dielectric behavior to bulk conductivities of 10-2 Sm-1 and were found to depend strongly on the surface modification methods of MWCNTs.

Topography and Mechanical Property Mapping of International Simple Glass Surfaces with Atomic Force Microscopy

Energy Technology Data Exchange (ETDEWEB)

Pierce, Eric M [ORNL

2014-01-01

Quantitative Nanomechanical Peak Force (PF-QNM) TappingModeTM atomic force microscopy measurements are presented for the first time on polished glass surfaces. The PF-QNM technique allows for topography and mechanical property information to be measured simultaneously at each pixel. Results for the international simple glass which represents a simplified version of SON68 glass suggests an average Young s modulus of 78.8 15.1 GPa is within the experimental error of the modulus measured for SON68 glass (83.6 2 GPa) with conventional approaches. Application of the PF-QNM technique will be extended to in situ glass corrosion experiments with the goal of gaining atomic-scale insights into altered layer development by exploiting the mechanical property differences that exist between silica gel (e.g., altered layer) and pristine glass surface.

Constructing dual-defense mechanisms on membrane surfaces by synergy of PFSA and SiO2 nanoparticles for persistent antifouling performance

Science.gov (United States)

Zhou, Linjie; Gao, Kang; Jiao, Zhiwei; Wu, Mengyuan; He, Mingrui; Su, Yanlei; Jiang, Zhongyi

2018-05-01

Synthetic antifouling membrane surfaces with dual-defense mechanisms (fouling-resistant and fouling-release mechanism) were constructed through the synergy of perfluorosulfonic acid (PFSA) and SiO2 nanoparticles. During the nonsolvent induced phase separation (NIPS) process, the amphiphilic PFSA polymers spontaneously segregated to membrane surfaces and catalyzed the hydrolysis-polycondensation of tetraethyl orthosilicate (TEOS) to generate hydrophilic SiO2 nanoparticles (NPs). The resulting PVDF/PFSA/SiO2 hybrid membranes were characterized by contact angle measurements, FTIR, XPS, SEM, AFM, TGA, and TEM. The hydrophilic microdomains and low surface energy microdomains of amphiphilic PFSA polymers respectively endowed membrane surfaces with fouling-resistant mechanism and fouling-release mechanism, while the hydrophilic SiO2 NPs intensified the fouling-resistant mechanism. When the addition of TEOS reached 3 wt%, the hybrid membrane with optimal synergy of PFSA and SiO2 NPs displayed low flux decline (17.4% DRt) and high flux recovery (99.8% FRR) during the filtration of oil-in-water emulsion. Meanwhile, the long-time stability test verified that the hybrid membrane possessed persistent antifouling performance.

Reduction mechanisms of ethylene carbonate on si anodes of lithium-ion batteries: effects of degree of lithiation and nature of exposed surface.

Science.gov (United States)

Martinez de la Hoz, Julibeth M; Leung, Kevin; Balbuena, Perla B

2013-12-26

Ab initio molecular dynamics simulations are used to identify mechanisms of reduction of ethylene carbonate on Si surfaces at various degrees of lithiation, where the low-coordinated surface Si atoms are saturated with O, OH, or H functional groups. The lowest Si content surfaces are represented by quasi-amorphous LiSi4 and LiSi2; intermediate lithiation is given by LiSi crystalline facets, and the highest Li content is studied through Li13Si4 surfaces. It is found that ethylene carbonate (EC) reduction mechanisms depend significantly on the degree of lithiation of the surface. On LiSi surfaces EC is reduced according to two different two-electron mechanisms (one simultaneous and one sequential), which are independent of specific surface functionalization or nature of exposed facets. On the less lithiated surfaces, the simultaneous two-electron reduction is found more frequently. In that mechanism, the EC reduction is initiated by the formation of a C-Si bond that allows adsorption of the intact molecule to the surface and is followed by electron transfer and ring-opening. Strongly lithiated Li13Si4 surfaces are found to be highly reactive. Reduction of adsorbed EC molecules occurs via a four-electron mechanism yielding as reduction products CO(2-) and O(C2H4)O(2-). Direct transfer of two electrons to EC molecules in liquid phase is also possible, resulting in the presence of O(C2H4)OCO(2-) anions in the liquid phase.

ENGAGEMENT AND BURNOUT AMONG NURSING AND PSYCHOLOGY STUDENTS IN SLOVAKIA

Directory of Open Access Journals (Sweden)

Zuzana Škodová

2017-05-01

Full Text Available Aim: The aim of the study was to examine the differences in engagement and burnout syndrome in students of nursing/midwifery and psychology in Slovakia. Design: A cross-sectional design was used. Methods: 171 university students on a baccalaureate program participated in the research (90.9% females; age 20.6 ± 1.3; 80 psychology students, 91 nursing/midwifery students. The School Burnout Inventory (SBI and Utrecht Work Engagement Scale (UWES were employed as measurement methods. Results: A significant negative association between levels of burnout and engagement (R = 0.42; p < 0.01 was found. A linear regression model showed a significant effect of engagement on burnout (β = -0.34; 95% CI: -0.50; -0.19. However, the total explained variance was only 19.4%. Students of psychology scored higher in engagement compared to nursing and midwifery students (t = 6.89; p < 0.001. Conversely, midwifery and nursing students had higher levels of burnout compared to the group of psychology students (t = -4.55; p < 0,001. Conclusion: Nursing is considered to be a high risk profession in terms of development of burnout, which was demonstrated in this study by the higher burnout, and lower engagement levels in nursing and midwifery students. Higher attention to coping mechanisms for stress and burnout symptoms among students of healthcare professions is required in the school curriculum, especially in nursing programs. Keywords: burnout syndrome, engagement, students of nursing, midwifery, students of psychology, School Burnout Inventory (SBI, Utrecht Work Engagement Scale (UWES.

Kinetic and mechanism studies of the adsorption of lead onto waste cow bone powder (WCBP) surfaces.

Science.gov (United States)

Cha, Jihoon; Cui, Mingcan; Jang, Min; Cho, Sang-Hyun; Moon, Deok Hyun; Khim, Jeehyeong

2011-01-01

This study examines the adsorption isotherms, kinetics and mechanisms of Pb²(+) sorption onto waste cow bone powder (WCBP) surfaces. The concentrations of Pb²(+) in the study range from 10 to 90 mg/L. Although the sorption data follow the Langmuir and Freundlich isotherm, a detailed examination reveals that surface sorption or complexation and co-precipitation are the most important mechanisms, along with possibly ion exchange and solid diffusion also contributing to the overall sorption process. The co-precipitation of Pb²(+) with the calcium hydroxyapatite (Ca-HAP) is implied by significant changes in Ca²(+) and PO₄³⁻ concentrations during the metal sorption processes. The Pb²(+) sorption onto the WCBP surface by metal complexation with surface functional groups such as ≡ POH. The major metal surface species are likely to be ≡ POPb(+). The sorption isotherm results indicated that Pb²(+) sorption onto the Langmuir and Freundlich constant q(max) and K( F ) is 9.52 and 8.18 mg g⁻¹, respectively. Sorption kinetics results indicated that Pb²(+) sorption onto WCBP was pseudo-second-order rate constants K₂ was 1.12 g mg⁻¹ h⁻¹. The main mechanism is adsorption or surface complexation (≡POPb(+): 61.6%), co-precipitation or ion exchange [Ca₃(.)₉₃ Pb₁(.)₀₇ (PO₄)₃ (OH): 21.4%] and other precipitation [Pb 50 mg L⁻¹ and natural pH: 17%). Sorption isotherms showed that WCBP has a much higher Pb²(+) removal rate in an aqueous solution; the greater capability of WCBP to remove aqueous Pb²(+) indicates its potential as another promising way to remediate Pb²(+)-contaminated media.

Role of surface on the size-dependent mechanical properties of copper nano-wire under tensile load: A molecular dynamics simulation

Science.gov (United States)

Liu, Wei-Ting; Hsiao, Chun-I.; Hsu, Wen-Dung

2014-01-01

In this study we have used atomistic simulations to investigate the role of surface on the size-dependent mechanical properties of nano-wires. In particular, we have performed computational investigation on single crystal face-centered cubic copper nano-wires with diameters ranging from 2 to 20 nm. The wire axis for all the nano-wires are considered along the [0 0 1] direction. Characterization of the initial optimized structures revealed clear differences in interatomic spacing, stress, and potential energy in all the nano-wires. The mechanical properties with respect to wire diameter are evaluated by applying tension along the [0 0 1] direction until yielding. We have discussed the stress-strain relationships, Young's modulus, and the variation in potential energy from surface to the center of the wire for all the cases. Our results indicate that the mechanical response (including yield strain, Young's modulus, and resilience) is directly related to the proportion of surface to bulk type atoms present in each nano-wire. Thus the size-dependent mechanical properties of single crystal copper nano-wire within elastic region are attributed to the surface to volume ratio (surface effect). Using the calculated response, we have formulated a mathematical relationship, which predicts the nonlinear correlation between the mechanical properties and the diameter of the wire.

Below the Surface: The Relationship among Different Types of Motivation, Engagement, and Performance of Undergraduate Students in Taiwan

Science.gov (United States)

Hsieh, Tzu-Ling

2013-01-01

The purpose of this study is to investigate the relationship among learning motivation, engagement behaviors, and performance of undergraduate students. 178 junior students are surveyed from five colleges at a four-year research university in Taiwan. The scales of motivation, engagement, and perceived learning outcomes are adapted from the…

Workplace spirituality, work engagement and thriving at work

Directory of Open Access Journals (Sweden)

Freda van der Walt

2018-01-01

Full Text Available Orientation: In order to create competitive advantage in an increasingly turbulent economic environment, sustainability of high performance is crucial. Only a few individuals have the drive, mindset, discipline and ability to sustain high performance on a daily basis. Thus, it is necessary to consider what can be done so that employees can sustain high performance over the long term. Research purpose: The purpose of the study was to establish whether spiritual workplaces will enhance employees’ work engagement and thriving at work. Motivation for the study: Two important mechanisms for understanding the human dimension of sustainability are thriving at work and work engagement. However, because work engagement and thriving are affective-motivational states, it is necessary to consider contextual factors that promote these positive states. As work engagement and thriving at work move beyond mere energy, to a sense of connectedness, it seems important that spiritual workplaces are created. Research approach, design and method: The study was quantitative in nature, and data were collected from employees working at small, medium and macro enterprises (SMMEs in one geographical area in South Africa. The final sample consisted of 259 employees. A survey that was cross-sectional in nature was conducted by means of a self-administered questionnaire. Main findings: The findings of the study show that there is a positive and significant relationship between workplace spirituality, work engagement and thriving at work. Furthermore, workplace spirituality significantly influences the variance in both work engagement and thriving at work. Practical or managerial implications: In order for SMMEs to promote work engagement and thriving at work, spiritual workplaces need to be created. Furthermore, emphasis needs to be placed on the work experience, rather than on work outcomes. It is also important that SMMEs develop employees holistically, that they create

Transport mechanism of an initially spherical droplet on a combined hydrophilic/hydrophobic surface

Energy Technology Data Exchange (ETDEWEB)

Myong, Hyon Kook; Kwon, Young Hoo [Dept. of Mechanical Engineering, Kookmin University, Seoul (Korea, Republic of)

2015-11-15

Fluid transport is a key issue in the development of microfluidic systems. Recently, Myong (2014) has proposed a new concept for droplet transport without external power sources, and numerically validated the results for a hypothetical 2D shape, initially having a hemicylindrical droplet shape. Myong and Kwon (2015) have also examined the transport mechanism for an actual water droplet, initially having a 3D hemispherical shape, on a horizontal hydrophilic/hydrophobic surface, based on the numerical results of the time evolution of the droplet shape, as well as the total kinetic, gravitational, pressure and surface free energies inside the droplet. In this study, a 3D numerical analysis of an initially spherical droplet is carried out to establish a new concept for droplet transport. Further, the transport mechanism of an actual water droplet is examined in detail from the viewpoint of the capillarity force imbalance through the numerical results of droplet shape and various energies inside the droplet.

Surface mechanical attrition treatment induced phase transformation behavior in NiTi shape memory alloy

International Nuclear Information System (INIS)

Hu, T.; Wen, C.S.; Lu, J.; Wu, S.L.; Xin, Y.C.; Zhang, W.J.; Chu, C.L.; Chung, J.C.Y.; Yeung, K.W.K.; Kwok, D.T.K.; Chu, Paul K.

2009-01-01

The phase constituents and transformation behavior of the martensite B19' NiTi shape memory alloy after undergoing surface mechanical attrition treatment (SMAT) are investigated. SMAT is found to induce the formation of a parent B2 phase from the martensite B19' in the top surface layer. By removing the surface layer-by-layer, X-ray diffraction reveals that the amount of the B2 phase decreases with depth. Differential scanning calorimetry (DSC) further indicates that the deformed martensite in the sub-surface layer up to 300 μm deep exhibits the martensite stabilization effect. The graded phase structure and transformation behavior in the SMATed NiTi specimen can be attributed to the gradient change in strain with depth.

Mechanical characterisation of the first centimeters of concrete with surface waves

International Nuclear Information System (INIS)

Chekroun, M.

2008-01-01

Cover concrete is the part of concrete structures directly in contact with the outside. Its thickness is a few centimetres and its main role is to protect reinforcement bars. Surface waves with wavelength varying from a few millimetres to a few centimetres are used to characterise this cover concrete. An estimation of the properties of the propagation of waves (phase and group velocities, damping factor) may allow us to evaluate mechanical properties and to detect possible damages. However, these waves will interact strongly with the numerous heterogeneities of the concrete (sand, aggregates,.) which dimensions are close to the wavelength. Waves will propagate in a multiple scattering regime. These effects have to be quantified in order to separate them from other effects linked to mechanical properties. An analytical and numerical study present theories of effective mediums to describe coherent wave propagation in an elastic matrix with random elastic inclusions. These models are then extended to take into account the viscoelasticity of the materials and the granulometry. We quantify with such model the importance of multiple scattering on surface wave propagation in concrete. Experimental measurements are carried on, using a specific protocol and efficient signal processing methods, allowing precise evaluation of phase and group velocity and of the damping factor of coherent surface waves on concrete or mortar slabs. The results show that these three parameters can provide complementary information on concrete properties (water to cement ratio, aggregate distribution,...), but also on other phenomenon like varying effective properties with depth. Effects of multiple scattering predicted by the model are experimentally observed, which opens interesting perspectives for the inverse problem. (author)

Authentic leadership of preceptors: predictor of new graduate nurses' work engagement and job satisfaction.

Science.gov (United States)

Giallonardo, Lisa M; Wong, Carol A; Iwasiw, Carroll L

2010-11-01

To examine the relationships between new graduate nurses' perceptions of preceptor authentic leadership, work engagement and job satisfaction. During a time when the retention of new graduate nurses is of the upmost importance, the reliance on preceptors to facilitate the transition of new graduate nurses is paramount. A predictive non-experimental survey design was used to examine the relationships between study variables. The final sample consisted of 170 randomly selected Registered Nurses (RNs) with authentic leadership and work engagement. Furthermore, work engagement was found to partially mediate the relationship between authentic leadership of preceptors and engagement of new graduate nurses. New graduate nurses paired with preceptors who demonstrate high levels of authentic leadership feel more engaged and are more satisfied. Engagement is an important mechanism by which authentic leadership affects job satisfaction. Managers must be aware of the role preceptors' authentic leadership plays in promoting work engagement and job satisfaction of new nurses. © 2010 The Authors. Journal compilation © 2010 Blackwell Publishing Ltd.

Influence of epoxy, polytetrafluoroethylene (PTFE) and rhodium surface coatings on surface roughness, nano-mechanical properties and biofilm adhesion of nickel titanium (Ni-Ti) archwires

Science.gov (United States)

Asiry, Moshabab A.; AlShahrani, Ibrahim; Almoammar, Salem; Durgesh, Bangalore H.; Kheraif, Abdulaziz A. Al; Hashem, Mohamed I.

2018-02-01

Aim. To investigate the effect of epoxy, polytetrafluoroethylene (PTFE) and rhodium surface coatings on surface roughness, nano-mechanical properties and biofilm adhesion of nickel titanium (Ni-Ti) archwires Methods. Three different coated (Epoxy, polytetrafluoroethylene (PTFE) and rhodium) and one uncoated Ni-Ti archwires were evaluated in the present study. Surface roughness (Ra) was assessed using a non-contact surface profilometer. The mechanical properties (nano-hardness and elastic modulus) were measured using a nanoindenter. Bacterial adhesion assays were performed using Streptococcus mutans (MS) and streptococcus sobrinus (SS) in an in-vitro set up. The data obtained were analyzed using analyses of variance, Tukey’s post hoc test and Pearson’s correlation coefficient test. Result. The highest Ra values (1.29 ± 0.49) were obtained for epoxy coated wires and lowest Ra values (0.29 ± 0.16) were obtained for the uncoated wires. No significant differences in the Ra values were observed between the rhodium coated and uncoated archwires (P > 0.05). The highest nano-hardness (3.72 ± 0.24) and elastic modulus values (61.15 ± 2.59) were obtained for uncoated archwires and the lowest nano-hardness (0.18 ± 0.10) and elastic modulus values (4.84 ± 0.65) were observed for epoxy coated archwires. No significant differences in nano-hardness and elastic modulus values were observed between the coated archwires (P > 0.05). The adhesion of Streptococcus mutans (MS) to the wires was significantly greater than that of streptococcus sobrinus (SS). The epoxy coated wires demonstrated an increased adhesion of MS and SS and the uncoated wires demonstrated decreased biofilm adhesion. The Spearman correlation test showed that MS and SS adhesion was positively correlated with the surface roughness of the wires. Conclusion. The different surface coatings significantly influence the roughness, nano-mechanical properties and biofilm adhesion parameters of the archwires. The

Flux quantization and quantum mechanics on Riemann surfaces in an external magnetic field

International Nuclear Information System (INIS)

Bolte, J.; Steiner, F.

1990-10-01

We investigate the possibility to apply an external constant magnetic field to a quantum mechanical system consisting of a particle moving on a compact or non-compact two-dimensional manifold of constant negative Gaussian curvature and of finite volume. For the motion on compact Riemann surfaces we find that a consistent formulation is only possible if the magnetic flux is quantized, as it is proportional to the (integrated) first Chern class of a certain complex line bundle over the manifold. In the case of non-compact surfaces of finite volume we obtain the striking result that the magnetic flux has to vanish identically due to the theorem that any holomorphic line bundle over a non-compact Riemann surface is holomorphically trivial. (orig.)

Surface topography and contact mechanics of dry and wet human skin

Directory of Open Access Journals (Sweden)

Alexander E. Kovalev

2014-08-01

Full Text Available The surface topography of the human wrist skin is studied by using optical and atomic force microscopy (AFM methods. By using these techniques the surface roughness power spectrum is obtained. The Persson contact mechanics theory is used to calculate the contact area for different magnifications, for the dry and wet skin. The measured friction coefficient between a glass ball and dry and wet skin can be explained assuming that a frictional shear stress σf ≈ 13 MPa and σf ≈ 5 MPa, respectively, act in the area of real contact during sliding. These frictional shear stresses are typical for sliding on surfaces of elastic bodies. The big increase in friction, which has been observed for glass sliding on wet skin as the skin dries up, can be explained as result of the increase in the contact area arising from the attraction of capillary bridges. Finally, we demonstrated that the real contact area can be properly defined only when a combination of both AFM and optical methods is used for power spectrum calculation.

Mechanical Characterization of Nanoporous Thin Films by Nanoindentation and Laser-induced Surface Acoustic Waves

Science.gov (United States)

Chow, Gabriel

Thin films represent a critical sector of modern engineering that strives to produce functional coatings at the smallest possible length scales. They appear most commonly in semiconductors where they form the foundation of all electronic circuits, but exist in many other areas to provide mechanical, electrical, chemical, and optical properties. The mechanical characterization of thin films has been a continued challenge due foremost to the length scales involved. However, emerging thin films focusing on materials with significant porosity, complex morphologies, and nanostructured surfaces produce additional difficulties towards mechanical analysis. Nanoindentation has been the dominant thin film mechanical characterization technique for the last decade because of the quick results, wide range of sample applicability, and ease of sample preparation. However, the traditional nanoindentation technique encounters difficulties for thin porous films. For such materials, alternative means of analysis are desirable and the lesser known laser-induced surface acoustic wave technique (LiSAW) shows great potential in this area. This dissertation focuses on studying thin, porous, and nanostructured films by nanoindentation and LiSAW techniques in an effort to directly correlate the two methodologies and to test the limits and applicabilities of each technique on challenging media. The LiSAW technique is particularly useful for thin porous films because unlike indentation, the substrate is properly accounted for in the wave motion analysis and no plastic deformation is necessary. Additionally, the use of lasers for surface acoustic wave generation and detection allows the technique to be fully non-contact. This is desirable in the measurement of thin, delicate, and porous films where physical sample probing may not be feasible. The LiSAW technique is also valuable in overcoming nanoscale roughness, particularly for films that cannot be mechanically polished, since typical SAW

Breakage mechanics for granular materials in surface-reactive environments

Science.gov (United States)

Zhang, Yida; Buscarnera, Giuseppe

2018-03-01

It is known that the crushing behaviour of granular materials is sensitive to the state of the fluids occupying the pore space. Here, a thermomechanical theory is developed to link such macroscopic observations with the physico-chemical processes operating at the microcracks of individual grains. The theory relies on the hypothesis that subcritical fracture propagation at intra-particle scale is the controlling mechanism for the rate-dependent, water-sensitive compression of granular specimens. First, the fracture of uniaxially compressed particles in surface-reactive environments is studied in light of irreversible thermodynamics. Such analysis recovers the Gibbs adsorption isotherm as a central component linking the reduction of the fracture toughness of a solid to the increase of vapour concentration. The same methodology is then extended to assemblies immersed in wet air, for which solid-fluid interfaces have been treated as a separate phase. It is shown that this choice brings the solid surface energy into the dissipation equations of the granular matrix, thus providing a pathway to (i) integrate the Gibbs isotherm with the continuum description of particle assemblies and (ii) reproduce the reduction of their yield strength in presence of high relative humidity. The rate-effects involved in the propagation of cracks and the evolution of breakage have been recovered by considering non-homogenous dissipation potentials associated with the creation of surface area at both scales. It is shown that the proposed model captures satisfactorily the compression response of different types of granular materials subjected to varying relative humidity. This result was achieved simply by using parameters based on the actual adsorption characteristics of the constituting minerals. The theory therefore provides a physically sound and thermodynamically consistent framework to study the behaviour of granular solids in surface-reactive environments.

Preparation of Artificial Skin that Mimics Human Skin Surface and Mechanical Properties.

Science.gov (United States)

Shimizu, Rana; Nonomura, Yoshimune

2018-01-01

We have developed an artificial skin that mimics the morphological and mechanical properties of human skin. The artificial skin comprises a polyurethane block possessing a microscopically rough surface. We evaluated the tactile sensations when skin-care cream was applied to the artificial skin. Many subjects perceived smooth, moist, and soft feels during the application process. Cluster analysis showed that these characteristic tactile feels are similar to those when skin-care cream is applied to real human skin. Contact angle analysis showed that an oil droplet spread smoothly on the artificial skin surface, which occurred because there were many grooves several hundred micrometers in width on the skin surface. In addition, when the skin-care cream was applied, the change in frictional force during the dynamic friction process increased. These wetting and frictional properties are important factors controlling the similarity of artificial skin to real human skin.

Hydraulic running and release tool with mechanical emergency release

International Nuclear Information System (INIS)

Baker, S.F.

1991-01-01

This patent describes a setting tool for connection in a well string to position a tubular member in a well bore. It comprises: a mandrel adapted to be connected to the well string; an outer sleeve surrounding the mandrel and releasably secured thereto; a latch nut releasably connected to the outer sleeve; piston means sealingly engaging the mandrel; shear means releasably securing the piston to the latch nut to maintain the latch nut releasably connected to the tubular member; the mandrel having port means for conducting fluid pressure from the well string to release the piston means from and the latch nut; cooperating engageable surfaces on the piston and latch nut to reengage them together after the piston moves a predetermined longitudinal distance relative to the latch nut; and additional cooperating engageable surfaces on the latch nut and the outer sleeve which are engageable when the piston and engaged latch nut are moved a predetermined additional longitudinal distance by fluid pressure to secure the engaged piston and latch nut with the outer sleeve for retrieval along with the mandrel from the well bore

Disentangling the Overlap Between Employee Engagement and Passion

Directory of Open Access Journals (Sweden)

Gaja Zager Kocjan

2015-07-01

Full Text Available With the emergence of positive psychology and the subsequent positive organizational behavior movement, focusing on the employee experience and factors of positive psychological states in employees has come to the forefront. In recent years, several studies have emphasized the practical value of employee engagement and passion (the dualistic model of passion; Vallerand et al., 2003 in predicting various positive individual and organizational outcomes (e.g., performance, well-being. Although engagement and passion seem relatively easy to spot at first glance, they are rather difficult to define and distinguish one from another. Therefore, the aim of the present article is to provide a comprehensive discussion on the shared aspects and conceptual differences between these two constructs within the work environment. The most noticeable overlap is proposed to exist between engagement and harmonious passion. It concerns the common underlying development mechanism, a very strong motivational force to engage in one's work, strong identification with work, and similar relationships with various antecedents and consequences. It is suggested that broader scope theories (such as the self-determination theory should be taken into consideration in order to unify common findings from both theoretical backgrounds and overcome redundancy and the risk of multiplication of concepts in positive psychology.

Analysis of engagement behavior in children during dyadic interactions using prosodic cues.

Science.gov (United States)

Gupta, Rahul; Bone, Daniel; Lee, Sungbok; Narayanan, Shrikanth

2016-05-01

Child engagement is defined as the interaction of a child with his/her environment in a contextually appropriate manner. Engagement behavior in children is linked to socio-emotional and cognitive state assessment with enhanced engagement identified with improved skills. A vast majority of studies however rely solely, and often implicitly, on subjective perceptual measures of engagement. Access to automatic quantification could assist researchers/clinicians to objectively interpret engagement with respect to a target behavior or condition, and furthermore inform mechanisms for improving engagement in various settings. In this paper, we present an engagement prediction system based exclusively on vocal cues observed during structured interaction between a child and a psychologist involving several tasks. Specifically, we derive prosodic cues that capture engagement levels across the various tasks. Our experiments suggest that a child's engagement is reflected not only in the vocalizations, but also in the speech of the interacting psychologist. Moreover, we show that prosodic cues are informative of the engagement phenomena not only as characterized over the entire task (i.e., global cues), but also in short term patterns (i.e., local cues). We perform a classification experiment assigning the engagement of a child into three discrete levels achieving an unweighted average recall of 55.8% (chance is 33.3%). While the systems using global cues and local level cues are each statistically significant in predicting engagement, we obtain the best results after fusing these two components. We perform further analysis of the cues at local and global levels to achieve insights linking specific prosodic patterns to the engagement phenomenon. We observe that while the performance of our model varies with task setting and interacting psychologist, there exist universal prosodic patterns reflective of engagement.

Durability and Mechanical Performance of PMMA/Stone Sludge Nanocomposites for Acrylic Solid Surface Applications

Directory of Open Access Journals (Sweden)

Samah EL-Bashir

2017-11-01

Full Text Available Acrylic solid surface sheets were prepared by mixing different kinds of stone sludge fillers (SSF in Poly (methyl methacrylate (PMMA nanocomposites. PMMA nanocomposite syrups were made using free radical polymerization of methylmethacrylate (MMA, then two kinds of nanofillers were added, namely, hydrophilic nanosilica and clay Halloysite nanotubules (HNTs. Acrylic solid surface sheets were manufactured by mixing the syrups with SSFs. The morphology of the produced sheets was studied using optical, and Scanning Electron Microscopy (SEM that revealed the uniform distribution of stone sludge in the polymeric matrix. The study of the physical properties showed promising mechanical performance and durability of PMMA/SSF nanocomposites for acrylic solid surface applications.

Mitigating the surface urban heat island: Mechanism study and sensitivity analysis

Science.gov (United States)

Meng, Chunlei

2017-08-01

In a surface urban heat island (SUHI), the urban land surface temperature (LST) is usually higher than the temperature of the surrounding rural areas due to human activities and surface characteristics. Because a SUHI has many adverse impacts on urban environment and human health, SUHI mitigation strategies are very important. This paper investigates the mechanism of a SUHI based on the basic physical laws that control the formation of a SUHI; five mitigation strategies are proposed, namely: sprinkling and watering; paving a pervious surface; reducing the anthropogenic heat (AH) release; using a "white roof"; increasing the fractional vegetation cover or leaf area index (LAI). To quantify the effect of these mitigation strategies, 26 sets of experiments are designed and implemented by running the integrated urban land model (IUM). The results of the sensitivity analysis indicate that sprinkling and watering is an effective measure for mitigating a SUHI for an entire day. Decreasing the AH release is also useful for both night- and daytime SUHI mitigation; however, the cooling extent is proportional to the diurnal cycle of AH. Increasing the albedo can reduce the LST in the daytime, especially when the solar radiation is significant; the cooling extent is approximately proportional to the diurnal cycle of the net radiation. Increasing the pervious surface percentage can mitigate the SUHI especially in the daytime. Increasing the fractional vegetation cover can mitigate the SUHI in the daytime but may aggravate the SUHI at night.

Breakdown conditioning of copper, CuZr and GlidCop® : effect of mechanical surface treatments

CERN Document Server

Ramsvik, T; Calatroni, S; Taborelli, M; CERN. Geneva. TS Department

2007-01-01

Motivated by the need of novel materials for the CLIC accelerating structures to resist mechanical fatigue, the copper based metals Copper Zirconium C15000 (CuZr) and GlidCop® Al-15 C15715 have been investigated by DC breakdown measurements, and compared with commercially pure Oxygen-free Copper C10100 (Cu-OFE). In all three cases the saturated breakdown fields (Esat) are similar, despite significant differences in their tensile strengths. In addition, the choice of mechanical surface preparation techniques influences the final breakdown characteristics. For both CuZr and GlidCop® immediate conditioning takes place when the surfaces are prepared by milling. For electro discharge machined (EDM) surfaces, however, several breakdown events are needed to obtain saturation. Specifically, for EDM treated CuZr and GlidCop®, ~50 and ~200 breakdown events are required to reach Esat.

Adsorption and wetting mechanisms at the surface of aqueous hydrocarbon solutions as a possible source of atmospheric pollution

International Nuclear Information System (INIS)

Sadiki, M.; Quentel, F.; Elleouet, C.; Olier, R.; Privat, M.

2006-01-01

Hydrocarbons in solutions have been the subject of very few investigations despite their relevance, in particular, in situations where environmental mechanisms are involved. We present, here, a synthesis of several studies conducted within our laboratory about the adsorption, at the water surface, of benzene and cyclohexane from under-saturated solutions. The co-adsorption of lead nitrate is also evidenced, though it does not adsorb in absence of organic molecules in the surface. Most of the data reported here were collected from series of measurements made with a very uncommon method: the bubble column; this technique, though being very time-demanding and lacking of user-friendliness, proved its usefulness and relevance in the study of such weakly adsorbable, surface-tension inactive compounds. The study of mixtures is simple and requires no model, which is precious in environmental research. The gathered data demonstrate that, through mechanical mechanisms such as bubbling, co-adsorption can lead to the passing from water to the atmosphere of harmful non-soluble, poorly surface-active, components. (authors)

Biological and Mechanical Effects of Micro-Nanostructured Titanium Surface on an Osteoblastic Cell Line In vitro and Osteointegration In vivo.

Science.gov (United States)

Hao, Jingzu; Li, Ying; Li, Baoe; Wang, Xiaolin; Li, Haipeng; Liu, Shimin; Liang, Chunyong; Wang, Hongshui

2017-09-01

Hybrid micro-nanostructure implant surface was produced on titanium (Ti) surface by acid etching and anodic oxidation to improve the biological and mechanical properties. The biological properties of the micro-nanostructure were investigated by simulated body fluid (SBF) soaking test and MC3T3-E1 cell co-culture experiment. The cell proliferation, spreading, and bone sialoprotein (BSP) gene expression were examined by MTT, SEM, and reverse transcription-polymerase chain reaction (RT-PCR), respectively. In addition, the mechanical properties were evaluated by instrumented nanoindentation test and friction-wear test. Furthermore, the effect of the micro-nanostructure surface on implant osteointegration was examined by in vivo experiment. The results showed that the formation of bone-like apatite was accelerated on the micro-nanostructured Ti surface after immersion in simulated body fluid, and the proliferation, spreading, and BSP gene expression of the MC3T3-E1 cells were also upregulated on the modified surface. The micro-nanostructured Ti surface displayed decreased friction coefficient, stiffness value, and Young's modulus which were much closer to those of the cortical bone, compared to the polished Ti surface. This suggested much better mechanical match to the surrounding bone tissue of the micro-nanostructured Ti surface. Furthermore, the in vivo animal experiment showed that after implantation in the rat femora, the micro-nanostructure surface displayed higher bonding strength between bone tissues and implant; hematoxylin and eosin (H&E) staining suggested that much compact osteoid tissue was observed at the interface of Micro-nano-Ti-bone than polished Ti-bone interface after implantation. Based on these results mentioned above, it was concluded that the improved biological and mechanical properties of the micro-nanostructure endowed Ti surface with good biocompatibility and better osteointegration, implying the enlarged application of the micro

Molecular mechanism and function of CD40/CD40L engagement in the immune system.

Science.gov (United States)

Elgueta, Raul; Benson, Micah J; de Vries, Victor C; Wasiuk, Anna; Guo, Yanxia; Noelle, Randolph J

2009-05-01

During the generation of a successful adaptive immune response, multiple molecular signals are required. A primary signal is the binding of cognate antigen to an antigen receptor expressed by T and B lymphocytes. Multiple secondary signals involve the engagement of costimulatory molecules expressed by T and B lymphocytes with their respective ligands. Because of its essential role in immunity, one of the best characterized of the costimulatory molecules is the receptor CD40. This receptor, a member of the tumor necrosis factor receptor family, is expressed by B cells, professional antigen-presenting cells, as well as non-immune cells and tumors. CD40 binds its ligand CD40L, which is transiently expressed on T cells and other non-immune cells under inflammatory conditions. A wide spectrum of molecular and cellular processes is regulated by CD40 engagement including the initiation and progression of cellular and humoral adaptive immunity. In this review, we describe the downstream signaling pathways initiated by CD40 and overview how CD40 engagement or antagonism modulates humoral and cellular immunity. Lastly, we discuss the role of CD40 as a target in harnessing anti-tumor immunity. This review underscores the essential role CD40 plays in adaptive immunity.

Mechanisms for the reflection of light atoms from crystal surfaces at kilovolt energies

International Nuclear Information System (INIS)

Hou, M.; Robinson, M.T.

1978-01-01

The computer program MARLOWE was used to investigate the backscattering of protons from the (110) surface of a nickel crystal. Grazing incidence was considered so that anisotropic effects originated mainly from the surface region. The contribution of aligned scattering was studied by comparing the results with similar calculations for an amorphous target. Energy distributions of backscattered particles were investigated for incident energies ranging from 0.1 to 5 keV. The structure of these distributions was explained by making calculations for several target thickness. Specular reflection was found to depend on the structure of the first few atomic planes only. The (110) rows in the surface plane were responsible for focusing into surface semichannels. Focusing in these semichannels was found to be the strongest under total reflection conditions (below about 1.3 keV) while the scattering intensity from surface rows increased with increasing incident energy. The orientation of the plane of incidence was found to have large influence on the relative contributions of the reflection mechanisms involved. (orig.) [de

Effects of cavity surface temperature on mechanical properties of specimens with and without a weld line in rapid heat cycle molding

International Nuclear Information System (INIS)

Wang, Guilong; Zhao, Guoqun; Wang, Xiaoxin

2013-01-01

Highlights: ► Higher cavity surface temperature reduces tensile strength of non-weldline part. ► Higher cavity surface temperature increases weldline tensile strength for PS and PP. ► Higher cavity surface temperature reduces weldline tensile strength for ABS, ABS/PMMA, ABS/PMMA/nano-C a CO 3 and FRPP. ► Tensile strength is reduced more by the weldline than impact strength. ► FRPP has the lowest weld line factor than other plastics without reinforced fibers. - Abstract: Rapid heat cycle molding (RHCM) is a recently developed injection molding technology to enhance surface esthetic of the parts. By rapid heating and cooling of mold cavity surfaces in molding process, it can greatly alleviate or even eliminate the surface defects such as flow mark, weld line, glass fiber rich surface, silver mark, jetting mark, and swirl mark, and also improve gloss finish and dimensional accuracy without prolonging the molding cycle. Besides surface esthetic, mechanical property is also a very import issue for the molded plastic part. The aim of this study is focusing on the effects of the cavity surface temperature just before filling, T cs , in RHCM on the mechanical strength of the specimen with and without weld line. Six kinds of typical plastics including polystyrene (PS), polypropylene (PP), acrylonitrile butadiene styrene (ABS), acrylonitrile butadiene styrene/polymethylmethacrylate (ABS/PMMA), ABS/PMMA/nano-C a CO 3 and glass fiber reinforced polypropylene (FRPP) are used in experiments. The specimens with and without a weld line are produced with the different T cs on the developed electric-heating RHCM system. Tensile tests and notched Izod impact tests are conducted to characterize the mechanical strength of the specimens molded with different cavity surface temperatures. Simulations, differential scanning calorimetry (DSC), scanning electron microscope (SEM) and optical microscope are implemented to explain the impact mechanism of T cs on mechanical properties

Conditional internalization of PEGylated nanomedicines by PEG engagers for triple negative breast cancer therapy

Science.gov (United States)

Su, Yu-Cheng; Burnouf, Pierre-Alain; Chuang, Kuo-Hsiang; Chen, Bing-Mae; Cheng, Tian-Lu; Roffler, Steve R.

2017-06-01

Triple-negative breast cancer (TNBC) lacks effective treatment options due to the absence of traditional therapeutic targets. The epidermal growth factor receptor (EGFR) has emerged as a promising target for TNBC therapy because it is overexpressed in about 50% of TNBC patients. Here we describe a PEG engager that simultaneously binds polyethylene glycol and EGFR to deliver PEGylated nanomedicines to EGFR+ TNBC. The PEG engager displays conditional internalization by remaining on the surface of TNBC cells until contact with PEGylated nanocarriers triggers rapid engulfment of nanocargos. PEG engager enhances the anti-proliferative activity of PEG-liposomal doxorubicin to EGFR+ TNBC cells by up to 100-fold with potency dependent on EGFR expression levels. The PEG engager significantly increases retention of fluorescent PEG probes and enhances the antitumour activity of PEGylated liposomal doxorubicin in human TNBC xenografts. PEG engagers with specificity for EGFR are promising for improved treatment of EGFR+ TNBC patients.

Employee engagement: a prescription for organizational transformation.

Science.gov (United States)

Halm, Barry

2011-01-01

Ivanitskaya, Glazer, and Erofeev (2009) suggest that "the most fundamental element of any organization that helps the organization to survive is the individual person" (p. 109). It is the motivation of human capital that makes a health-care organization come to life. Health-care is a unique industry; its accomplishments are directly dependent upon the competencies and technical skills of its employees. "When people in the workplace fulfill their organizational roles, then the organization thrives" (Ivanitskaya et al., 2009, p. 110). Health-care systems will require organizations that thrive and exhibit characteristics of continuous growth, expressing excessive levels of energy and an immense capacity for flourishing. Anticipating the challenges of the next decade, health-care organizations must achieve a higher degree of employee engagement to enhance organizational performance and profitability. The data analyzed for this chapter indicate that employees who are engaged are more enthusiastic and aspired to achieve both individual and organizational success. The chapter concludes by suggesting five operating practices to establish an employee engagement culture--defining the employee's role in fulfilling the organization's purpose, selecting employees with capability and passion, supporting and valuing the employee, creating sustainable reward systems, and developing feedback and reinforcement mechanisms.

Clays causing adhesion with tool surfaces during mechanical tunnel driving

Science.gov (United States)

Spagnoli, G.; Fernández-Steeger, T.; Stanjek, H.; Feinendegen, M.; Post, C.; Azzam, R.

2009-04-01

During mechanical excavation with a tunnel boring machine (TBM) it is possible that clays stick to the cutting wheel and to other metal parts. The resulting delays in the progress of construction work, cause great economic damage and often disputes between the public awarding authorities and executing companies. One of the most important factors to reduce successfully the clay adhesion is the use of special polymers and foams. But why does the clay stick to the metal parts? A first step is to recognize which kind of clay mineralogy shows serious adhesion problems. The mechanical properties of clay and clay suspensions are primarily determined by surface chemistry and charge distribution at the interfaces, which in turn affect the arrangement of the clay structure. As we know, clay is a multi-phase material and its behaviour depends on numerous parameters such as: clay mineralogy, clay fraction, silt fraction, sand fraction, water content, water saturation, Atterberg limits, sticky limit, activity, cation exchange capacity, degree of consolidation and stress state. It is therefore likely that adhesion of clay on steel is also affected by these clay parameters. Samples of clay formations, which caused problems during tunnel driving, will be analyzed in laboratory. Mineralogical analyses (diffractometry, etc.) will be carried out to observe which minerals are responsible for adherence problems. To manipulate the physical properties, batch tests will be carried out in order to eliminate or reduce the adhesion on tool surfaces through variation of the zeta potential. Second step is the performance of vane shear tests on clay samples. Different pore fluid (distilled water, pure NaCl solution, ethanol and methanol) will be used to study the variation of the mechanical behaviour of clay depending on the dielectric constant of the fluids. This project is funded by the German Federal Ministry of Education and Research (BMBF) and the DFG (German Research Foundation) in the

Hydrogen induced surface effects on the mechanical properties of type 304 stainless steel

International Nuclear Information System (INIS)

Silva, T.C.V. da; Pascual, R.; Miranda, P.E.V. de.

1983-01-01

The possibilities of modifying the mechanical properties of type 304 stainless steel by cathodic hydrogen charging were studied. The situations analysed included hydrogen embrittlement itself in tensile tests of hydrogen containing samples and the effects of delayed cracks in fatigue tests of hydrogenated and outgassed samples. SEM and TEM observations were also performed. It was found that hydrogen induced surface delayed cracks appear in great quantity during outgassing (of the order of several millions in a square centimeter). Hydrogen embrittlement was responsible for drastic losses in ductility in tension, while surface cracks severely reduced fatigue life. (author) [pt

Probabilistic fracture mechanics of nuclear structural components. Consideration of transition from embedded crack to surface crack

International Nuclear Information System (INIS)

Yagawa, Genki; Yoshimura, Shinobu; Kanto, Yasuhiro

1998-01-01

This paper describes a probabilistic fracture mechanics (PFM) analysis of aged nuclear reactor pressure vessel (RPV) material. New interpolation formulas are first derived for both embedded elliptical surface cracks and semi-elliptical surface cracks. To investigate effects of transition from embedded crack to surface crack in PFM analyses, one of PFM round-robin problems set by JSME-RC111 committee, i.e. 'aged RPV under normal and upset operating conditions' is solved, employing the interpolation formulas. (author)

Representations of work engagement and workaholism in modern psychological research

Directory of Open Access Journals (Sweden)

Valentina V. Barabanshchikova

2015-03-01

Full Text Available The paper provides an overview of work engagement and workaholism, and also the current research. Work engagement differs from workaholism as a psychological phenomenon, but both concepts are closely connected with each other. The scientific research of the phenomena mentioned above began only in 1970, when Oates published his first book called “On being a “workaholic”. Each employee has to find balance between private life and work to get utmost job satisfaction, and to perform his/her job responsibilities productively. Work engaged staff have higher levels of subjective comfort and psychological well-being, without any experience of occupational deteriorations. In modern psychology, there is no prescription for perfect recipe of finding balance between work and family that entails different angles of considering work engagement and workaholism, their causes and prevention mechanisms. On the other hand, the impact of excessive work engagement may be one of the reasons of developing negative human functional states that plays a moderating role in the transit stage from work engagement to workaholism. Schaufeli discribed work engagement as a positive, affective-motivational state of fulfillment that can be characterized by vigor, dedication, and absorption. Workaholism is a multidimensional construct, which can be linked to both positive and negative outcomes. At the contemporary stage of scientific development a lot of difficulties in studying workaholism and work engagement could be analyzed, e.g. there are no adopted Russian diagnostics instruments to assess workaholism and its manifastations. Thus, further research should be devoted to the issues of choosing proper research instruments in order to obtain clear and reliable results.

Mechanisms for adsorption of organic bases on hydrated smectite surfaces

Energy Technology Data Exchange (ETDEWEB)

Laird, D.A.; Fleming, P.D.

1999-08-01

The environmental fate of anthropogenic organic bases introduced to soils and sediments, either deliberately as pesticides or inadvertently as contaminants, depends, to a large extent, on reactions between those compounds and the surfaces of soil mineral and organic constituents. Mechanisms by which organic bases are adsorbed on hydrated smectite surfaces were investigated. Three Ca-saturated reference smectites (Otay, SPV, and Panther Creek) were dispersed in distilled water containing 5 {micro}mol of pyridine or 3-butylpyridine. The pH was adjusted to between 7.5 and 3 using 0.01 M HCl. After a 2-h equilibration, the amounts of pyridine or 3-butylpyridine adsorbed on the clay and the amount of Ca desorbed from the clay were determined. Negligible amounts of pyridine were adsorbed by the Ca-smectites in the neutral systems (pH > 7); however, most of the added pyridine was adsorbed on the smectites in the acidified systems (pH < 5). Equivalent amounts of Ca{sup 2+} were desorbed from the clays, indicating that pyridine was adsorbed as a protonated species by cation exchange. By contrast, 40 to 90% of added 3-butylpyridine was adsorbed on the smectites at neutral pHs, whereas only small amounts of Ca{sup 2+} were desorbed. The results suggest that 3-butylpyridine is initially retained by hydrophobic bonding between the alkyl side chain of the molecule and hydrophobic nanosites located between the charge sites on smectite surfaces. Surface acidity catalyzed protonation 1 to 1.5 pH units above the pK{sub a} of the bases.

Designing for user engagement

CERN Document Server

Geisler, Cheryl

2013-01-01

Designing for User Engagement on the Web: 10 Basic Principles is concerned with making user experience engaging. The cascade of social web applications we are now familiar with - blogs, consumer reviews, wikis, and social networking - are all engaging experiences. But engagement is an increasingly common goal in business and productivity environments as well. This book provides a foundation for all those seeking to design engaging user experiences rich in communication and interaction. Combining a handbook on basic principles with case studies, it provides readers with a ric

Investigation of surface properties and adhesion mechanisms in the combination of different layers, with the aid of surface analysis methods

International Nuclear Information System (INIS)

Olschewski, T.

1991-01-01

The aim of the investigations was to characterize the surface properties of organic coating materials and inorganic substrates, which are relevant in the context of microstructure technique developments and to obtain information on the adhesion mechanisms present. Two systems were examined which play an important part in micro-technique, i.e.: for the LIGA process and in the development of micro-sensors based on Chem FET's for chemical analysis. For these systems, i.e.: PMMA/TiO 2 and PVC adipate/Si 3 N 4 , adhesion mechanisms were expected, which occur particularly frequently in adhesive combination of polymers with inorganic substrates, i.e.: the mechanical gearing between polymer molecules and substrate structures and a chemical interaction between the boundary layers of the organic top coating and the inorganic substrate. (orig./DG) [de

Student Engagement in Pharmacology Courses Using Online Learning Tools

Science.gov (United States)

Karaksha, Abdullah; Grant, Gary; Anoopkumar-Dukie, Shailendra; Nirthanan, S. Niru

2013-01-01

Objective. To assess factors influencing student engagement with e-tools used as a learning supplement to the standard curriculum in pharmacology courses. Design. A suite of 148 e-tools (interactive online teaching materials encompassing the basic mechanisms of action for different drug classes) were designed and implemented across 2 semesters for third-year pharmacy students. Assessment. Student engagement and use of this new teaching strategy were assessed using a survey instrument and usage statistics for the material. Use of e-tools during semester 1 was low, a finding attributable to a majority (75%) of students either being unaware of or forgetting about the embedded e-tools and a few (20%) lacking interest in accessing additional learning materials. In contrast to semester 1, e-tool use significantly increased in semester 2 with the use of frequent reminders and announcements (pstudent engagement after the implementation of a “marketing strategy” that included e-mail reminders and motivation. PMID:23966728

Engagement: Looking beyond the mirror to understand action understanding.

Science.gov (United States)

Reddy, Vasudevi; Uithol, Sebo

2016-03-01

In this paper, we argue that the current focus on mirroring as the route to explaining the development of action understanding is misleading and problematic. It facilitates a fundamentally spectatorial stance, ignoring engagement and dialogue; it focuses on similarity between self and other and neglects difference; and it succumbs to the static terminology of mechanism rather than a dynamic language of process. Contrary to this view, dialogic exchanges are evident from the start of life, revealing infants' ability to engage with and respond appropriately to actions that are outside their own motor repertoire. We suggest that engagement rather than mirroring better accounts for many current findings in action understanding. The neurological evidence to date shows that action perception involves a process of continuous synchronization and change, suggesting that it might be more fruitful for research and theory to look beyond mirroring and instead adopt dynamic processual explanations of action understanding within interaction. © 2015 The British Psychological Society.

Student engagement in pharmacology courses using online learning tools.

Science.gov (United States)

Karaksha, Abdullah; Grant, Gary; Anoopkumar-Dukie, Shailendra; Nirthanan, S Niru; Davey, Andrew K

2013-08-12

To assess factors influencing student engagement with e-tools used as a learning supplement to the standard curriculum in pharmacology courses. A suite of 148 e-tools (interactive online teaching materials encompassing the basic mechanisms of action for different drug classes) were designed and implemented across 2 semesters for third-year pharmacy students. Student engagement and use of this new teaching strategy were assessed using a survey instrument and usage statistics for the material. Use of e-tools during semester 1 was low, a finding attributable to a majority (75%) of students either being unaware of or forgetting about the embedded e-tools and a few (20%) lacking interest in accessing additional learning materials. In contrast to semester 1, e-tool use significantly increased in semester 2 with the use of frequent reminders and announcements (ponline teaching and learning resources were only effective in increasing student engagement after the implementation of a "marketing strategy" that included e-mail reminders and motivation.

Redirecting T cells to eradicate B-cell acute lymphoblastic leukemia: bispecific T-cell engagers and chimeric antigen receptors.

Science.gov (United States)

Aldoss, I; Bargou, R C; Nagorsen, D; Friberg, G R; Baeuerle, P A; Forman, S J

2017-04-01

Recent advances in antibody technology to harness T cells for cancer immunotherapy, particularly in the difficult-to-treat setting of relapsed/refractory acute lymphoblastic leukemia (r/r ALL), have led to innovative methods for directing cytotoxic T cells to specific surface antigens on cancer cells. One approach involves administration of soluble bispecific (or dual-affinity) antibody-based constructs that temporarily bridge T cells and cancer cells. Another approach infuses ex vivo-engineered T cells that express a surface plasma membrane-inserted antibody construct called a chimeric antigen receptor (CAR). Both bispecific antibodies and CARs circumvent natural target cell recognition by creating a physical connection between cytotoxic T cells and target cancer cells to activate a cytolysis signaling pathway; this connection allows essentially all cytotoxic T cells in a patient to be engaged because typical tumor cell resistance mechanisms (such as T-cell receptor specificity, antigen processing and presentation, and major histocompatibility complex context) are bypassed. Both the bispecific T-cell engager (BiTE) antibody construct blinatumomab and CD19-CARs are immunotherapies that have yielded encouraging remission rates in CD19-positive r/r ALL, suggesting that they might serve as definitive treatments or bridging therapies to allogeneic hematopoietic cell transplantation. With the introduction of these immunotherapies, new challenges arise related to unique toxicities and distinctive pathways of resistance. An increasing body of knowledge is being accumulated on how to predict, prevent, and manage such toxicities, which will help to better stratify patient risk and tailor treatments to minimize severe adverse events. A deeper understanding of the precise mechanisms of action and immune resistance, interaction with other novel agents in potential combinations, and optimization in the manufacturing process will help to advance immunotherapy outcomes in the r

Redirecting adenovirus tropism by genetic, chemical, and mechanical modification of the adenovirus surface for cancer gene therapy.

Science.gov (United States)

Yoon, A-Rum; Hong, Jinwoo; Kim, Sung Wan; Yun, Chae-Ok

2016-06-01

Despite remarkable advancements, clinical evaluations of adenovirus (Ad)-mediated cancer gene therapies have highlighted the need for improved delivery and targeting. Genetic modification of Ad capsid proteins has been extensively attempted. Although genetic modification enhances the therapeutic potential of Ad, it is difficult to successfully incorporate extraneous moieties into the capsid and the engineering process is laborious. Recently, chemical modification of the Ad surface with nanomaterials and targeting moieties has been found to enhance Ad internalization into the target by both passive and active mechanisms. Alternatively, external stimulus-mediated targeting can result in selective accumulation of Ad in the tumor and prevent dissemination of Ad into surrounding nontarget tissues. In the present review, we discuss various genetic, chemical, and mechanical engineering strategies for overcoming the challenges that hinder the therapeutic efficacy of Ad-based approaches. Surface modification of Ad by genetic, chemical, or mechanical engineering strategies enables Ad to overcome the shortcomings of conventional Ad and enhances delivery efficiency through distinct and unique mechanisms that unmodified Ad cannot mimic. However, although the therapeutic potential of Ad-mediated gene therapy has been enhanced by various surface modification strategies, each strategy still possesses innate limitations that must be addressed, requiring innovative ideas and designs.

Exposing Students to the Potential and Risks of Stakeholder Engagement when Teaching Sustainability: A Classroom Exercise

Science.gov (United States)

Collins, Eva; Kearins, Kate

2007-01-01

In-class, stakeholder negotiation exercises are proposed as a means of students experiencing and reflecting critically on the potential and the risks of an increasingly popular mechanism for advancing sustainability--stakeholder engagement. This article reviews the theoretical framework for stakeholder engagement and for an issue-based rather than…

Investigation of Range Profiles from a Simplified Ship on Rough Sea Surface and Its Multipath Imaging Mechanisms

Directory of Open Access Journals (Sweden)

Siyuan He

2012-01-01

Full Text Available The range profiles of a two-dimension (2 D perfect electric conductor (PEC ship on a wind-driven rough sea surface are derived by performing an inverse discrete Fourier transform (IDFT on the wide band backscattered field. The rough sea surface is assuming to be a PEC surface. The back scattered field is computed based on EM numerical simulation when the frequencies are sampled between 100 MHz and 700 MHz. Considering the strong coupling interactions between the ship and sea, the complicated multipath effect to the range profile characteristics is fully analyzed based on the multipath imaging mechanisms. The coupling mechanisms could be explained by means of ray theory prediction and numerical extraction of the coupling currents. The comparison of the range profile locations between ray theory prediction and surface current simulation is implemented and analyzed in this paper. Finally, the influence of different sea states on the radar target signatures has been examined and discussed.

Stereoscopic 3D video games and their effects on engagement

Science.gov (United States)

Hogue, Andrew; Kapralos, Bill; Zerebecki, Chris; Tawadrous, Mina; Stanfield, Brodie; Hogue, Urszula

2012-03-01

With television manufacturers developing low-cost stereoscopic 3D displays, a large number of consumers will undoubtedly have access to 3D-capable televisions at home. The availability of 3D technology places the onus on content creators to develop interesting and engaging content. While the technology of stereoscopic displays and content generation are well understood, there are many questions yet to be answered surrounding its effects on the viewer. Effects of stereoscopic display on passive viewers for film are known, however video games are fundamentally different since the viewer/player is actively (rather than passively) engaged in the content. Questions of how stereoscopic viewing affects interaction mechanics have previously been studied in the context of player performance but very few have attempted to quantify the player experience to determine whether stereoscopic 3D has a positive or negative influence on their overall engagement. In this paper we present a preliminary study of the effects stereoscopic 3D have on player engagement in video games. Participants played a video game in two conditions, traditional 2D and stereoscopic 3D and their engagement was quantified using a previously validated self-reporting tool. The results suggest that S3D has a positive effect on immersion, presence, flow, and absorption.

"Engage" therapy: Prediction of change of late-life major depression.

Science.gov (United States)

Alexopoulos, George S; O'Neil, Robert; Banerjee, Samprit; Raue, Patrick J; Victoria, Lindsay W; Bress, Jennifer N; Pollari, Cristina; Arean, Patricia A

2017-10-15

Engage grew out of the need for streamlined psychotherapies that can be accurately used by community therapists in late-life depression. Engage was based on the view that dysfunction of reward networks is the principal mechanism mediating depressive symptoms. Accordingly, Engage uses "reward exposure" (exposure to meaningful activities) and assumes that repeated activation of reward networks will normalize these systems. This study examined whether change in a behavioral activation scale, an index of reward system function, predicts change in depressive symptomatology. The participants (N = 48) were older adults with major depression treated with 9 weekly sessions of Engage and assessed 27 weeks after treatment. Depression was assessed with the 24-item Hamilton Depression Rating Scale (HAM-D) and behavioral activation with the four subscales of Behavioral Activation for Depression Scale (activation, avoidance/rumination, work impairment, social impairment) at baseline, 6 weeks (mid-treatment), 9 weeks (end of treatment), and 36 weeks. Change only in the Activation subscale during successive periods of assessment predicted depression severity (HAM-D) at the end of each period (F 1, 47 = 21.05, psocial support. Change in behavioral activation predicts improvement of depressive symptoms and signs in depressed older adults treated with Engage. Copyright © 2017. Published by Elsevier B.V.

Influence of surface properties on the mechanism of H2S removal by alkaline activated carbons.

Science.gov (United States)

Yan, Rong; Chin, Terence; Ng, Yuen Ling; Duan, Huiqi; Liang, David Tee; Tay, Joo Hwa

2004-01-01

Alkaline activated carbons are widely used as adsorbents of hydrogen sulfide (H2S), one of the major odorous compounds arising from sewage treatment facilities. Although a number of studies have explored the effects of various parameters, mechanisms of H2S adsorption by alkaline carbons are not yet fully understood. The major difficulty seems to lie in the fact that little is known with certainty about the predominant reactions occurring on the carbon surface. In this study, the surface properties of alkaline activated carbons were systematically investigated to further exploit and better understand the mechanisms of H2S adsorption by alkaline activated carbons. Two commercially available alkaline activated carbons and their representative exhausted samples (8 samples collected at different height of the column after H2S breakthrough tests) were studied. The 8 portions of the exhausted carbon were used to represent the H2S/carbon reaction process. The surface properties of both the original and the exhausted carbons were characterized using the sorption of nitrogen (BET test), surface pH, Boehm titration, thermal and FTIR analysis. Porosity and surface area provide detailed information about the pore structure of the exhausted carbons with respect to the reaction extent facilitating the understanding of potential pore blockages. Results of Boehm titration and FTIR both demonstrate the significant effects of surface functional groups, and identification of oxidation products confirmed the different mechanisms involved with the two carbons. From the DTG curves of thermal analysis, two well-defined peaks representing two products of surface reactions (i.e., sulfur and sulfuric acid) were observed from the 8 exhausted portions with gradually changing patterns coinciding with the extent of the reaction. Surface pH values of the exhausted carbons show a clear trend of pH drop along the reaction extent, while pH around 2 was observed for the bottom of the bed indicating

Probabilistic fracture mechanics of nuclear structural components: consideration of transition from embedded crack to surface crack

International Nuclear Information System (INIS)

Yagawa, G.; Yoshimura, S.

1999-01-01

This paper describes a probabilistic fracture mechanics (PFM) analysis of aged nuclear reactor pressure vessel (RPV) material. New interpolation formulas of three-dimensional stress intensity factors are presented for both embedded elliptical surface cracks and semi-elliptical surface cracks. To investigate effects of transition from embedded crack to surface crack in PFM analyses, one of the PFM round-robin problems set by JSME-RC111 committee (i.e. aged RPV under normal and upset operating conditions) is solved, employing the interpolation formulas. (orig.)

Facile fabrication of hydrophobic surfaces on mechanically alloyed-Mg/HA/TiO{sub 2}/MgO bionanocomposites

Energy Technology Data Exchange (ETDEWEB)

Khalajabadi, Shahrouz Zamani [Medical Devices and Technology Group (MEDITEG), Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Abdul Kadir, Mohammed Rafiq, E-mail: rafiq@biomedical.utm.my [Medical Devices and Technology Group (MEDITEG), Faculty of Biosciences and Medical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia); Izman, Sudin; Mohd Yusop, Mohd Zamri [Department of Materials, Manufacturing and Industrial Engineering, Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia)

2015-01-01

Highlights: • Mg/HA/TiO{sub 2}-based nanocomposite was produced using mechanical alloying. • The hydrophobic surface coverage was fabricated on the mechanical alloyed samples by annealing. • The morphological characteristics, phase evolution and wettability of nanocomposites and the hydrophobic surface coverage were investigated. • The activation energies and reaction kinetic of the powder mixture of nanocomposites were calculated. - Abstract: The effect of mechanical alloying and post-annealing on the phase evolution, microstructure, wettability and thermal stability of Mg–HA–TiO{sub 2}–MgO composites was investigated in this study. Phase evolution and microstructure analysis were performed using X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscopy and atomic force microscopy, as well as the wettability determined by contact angle measurements with SBF. The 16-h mechanical alloying resulted in the formation of MgTiO{sub 3}, CaTiO{sub 3}, Mg{sub 3}(PO{sub 4}){sub 2} and Mg(OH){sub 2} phases and a decrease in wettability of the nanocomposites. A hydrophobic film with hierarchical structures comprising nanoflakes of MgTiO{sub 3}, nano-cuboids of CaTiO{sub 3}, microspheres of Mg{sub 3}(PO{sub 4}){sub 2} and Mg(OH){sub 2} was successfully constructed on the surface of the Mg-based nanocomposites substrates as a result of the post-annealing process. After 1-h annealing at 630 °C, the synthesized hydrophobic surface on the nanocomposite substrates decreased the wettability, as the 8-h-mechanically alloyed samples exhibited a contact angle close to 93°. The formation activation energies and reaction kinetics of the powder mixture were investigated using differential thermal analysis and thermal gravimetric analysis. The released heat, weight loss percentage and reaction kinetics increased, while the formation activation energies of the exothermic reactions decreased following an increase in the milling time.

Fabrication mechanism of friction-induced selective etching on Si(100) surface.

Science.gov (United States)

Guo, Jian; Song, Chenfei; Li, Xiaoying; Yu, Bingjun; Dong, Hanshan; Qian, Linmao; Zhou, Zhongrong

2012-02-23

As a maskless nanofabrication technique, friction-induced selective etching can easily produce nanopatterns on a Si(100) surface. Experimental results indicated that the height of the nanopatterns increased with the KOH etching time, while their width increased with the scratching load. It has also found that a contact pressure of 6.3 GPa is enough to fabricate a mask layer on the Si(100) surface. To understand the mechanism involved, the cross-sectional microstructure of a scratched area was examined, and the mask ability of the tip-disturbed silicon layer was studied. Transmission electron microscope observation and scanning Auger nanoprobe analysis suggested that the scratched area was covered by a thin superficial oxidation layer followed by a thick distorted (amorphous and deformed) layer in the subsurface. After the surface oxidation layer was removed by HF etching, the residual amorphous and deformed silicon layer on the scratched area can still serve as an etching mask in KOH solution. The results may help to develop a low-destructive, low-cost, and flexible nanofabrication technique suitable for machining of micro-mold and prototype fabrication in micro-systems.

The ABCs of Student Engagement

Science.gov (United States)

Parsons, Seth A.; Nuland, Leila Richey; Parsons, Allison Ward

2014-01-01

Student engagement is an important consideration for teachers and administrators because it is explicitly associated with achievement. What the authors call the ABC's of engagement they outline as: Affective engagement, Behavioral engagement, and Cognitive engagement. They also present "Three Things Every Teacher Needs to Know about…

Mechanisms of Surface-Mediated DNA Hybridization

Science.gov (United States)

2015-01-01

Single-molecule total internal reflection fluorescence microscopy was employed in conjunction with resonance energy transfer (RET) to observe the dynamic behavior of donor-labeled ssDNA at the interface between aqueous solution and a solid surface decorated with complementary acceptor-labeled ssDNA. At least 100 000 molecular trajectories were determined for both complementary strands and negative control ssDNA. RET was used to identify trajectory segments corresponding to the hybridized state. The vast majority of molecules from solution adsorbed nonspecifically to the surface, where a brief two-dimensional search was performed with a 7% chance of hybridization. Successful hybridization events occurred with a characteristic search time of ∼0.1 s, and unsuccessful searches resulted in desorption from the surface, ultimately repeating the adsorption and search process. Hybridization was reversible, and two distinct modes of melting (i.e., dehybridization) were observed, corresponding to long-lived (∼15 s) and short-lived (∼1.4 s) hybridized time intervals. A strand that melted back onto the surface could rehybridize after a brief search or desorb from the interface. These mechanistic observations provide guidance for technologies that involve DNA interactions in the near-surface region, suggesting a need to design surfaces that both enhance the complex multidimensional search process and stabilize the hybridized state. PMID:24708278

Growth mechanisms for Si epitaxy on O atomic layers: Impact of O-content and surface structure

Energy Technology Data Exchange (ETDEWEB)

Jayachandran, Suseendran, E-mail: suseendran.jayachandran@imec.be [Imec, Kapeldreef 75, 3001 Leuven (Belgium); KU Leuven (University of Leuven), Department of Metallurgy and Materials, Castle Arenberg 44, B-3001 Leuven (Belgium); Billen, Arne [Imec, Kapeldreef 75, 3001 Leuven (Belgium); KU Leuven (University of Leuven), Department of Chemistry, Celestijnenlaan 200F, B-3001 Leuven (Belgium); Douhard, Bastien; Conard, Thierry; Meersschaut, Johan; Moussa, Alain; Caymax, Matty; Bender, Hugo [Imec, Kapeldreef 75, 3001 Leuven (Belgium); Vandervorst, Wilfried [Imec, Kapeldreef 75, 3001 Leuven (Belgium); KU Leuven (University of Leuven), Department of Physics and Astronomy, Celestijnenlaan 200D, B-3001 Leuven (Belgium); Heyns, Marc [Imec, Kapeldreef 75, 3001 Leuven (Belgium); KU Leuven (University of Leuven), Department of Metallurgy and Materials, Castle Arenberg 44, B-3001 Leuven (Belgium); Delabie, Annelies [Imec, Kapeldreef 75, 3001 Leuven (Belgium); KU Leuven (University of Leuven), Department of Chemistry, Celestijnenlaan 200F, B-3001 Leuven (Belgium)

2016-10-30

Highlights: • O{sub 3} or O{sub 2} exposures on H-Si(100) result in O ALs with different surface structures. • Si-EPI on O AL using O{sub 3} process is by direct epitaxial growth mechanism. • Si-EPI on O AL using O{sub 2} process is by epitaxial lateral overgrowth mechanism. • Distortions by O AL, SiH{sub 4} flux rate and Si thickness has an impact on Si-EPI quality. - Abstract: The epitaxial growth of Si layers on Si substrates in the presence of O atoms is generally considered a challenge, as O atoms degrade the epitaxial quality by generating defects. Here, we investigate the growth mechanisms for Si epitaxy on O atomic layers (ALs) with different O-contents and structures. O ALs are deposited by ozone (O{sub 3}) or oxygen (O{sub 2}) exposure on H-terminated Si at 50 °C and 300 °C respectively. Epitaxial Si is deposited by chemical vapor deposition using silane (SiH{sub 4}) at 500 °C. After O{sub 3} exposure, the O atoms are uniformly distributed in Si-Si dimer/back bonds. This O layer still allows epitaxial seeding of Si. The epitaxial quality is enhanced by lowering the surface distortions due to O atoms and by decreasing the arrival rate of SiH{sub 4} reactants, allowing more time for surface diffusion. After O{sub 2} exposure, the O atoms are present in the form of SiO{sub x} clusters. Regions of hydrogen-terminated Si remain present between the SiO{sub x} clusters. The epitaxial seeding of Si in these structures is realized on H-Si regions, and an epitaxial layer grows by a lateral overgrowth mechanism. A breakdown in the epitaxial ordering occurs at a critical Si thickness, presumably by accumulation of surface roughness.

Engaging with Assessment: Increasing Student Engagement through Continuous Assessment

Science.gov (United States)

Holmes, Naomi

2018-01-01

Student engagement is intrinsically linked to two important metrics in learning: student satisfaction and the quality of the student experience. One of the ways that engagement can be influenced is through careful curriculum design. Using the knowledge that many students are "assessment-driven," a low-stakes continuous weekly summative…

University student’s engagement: development of the University Student Engagement Inventory (USEI

Directory of Open Access Journals (Sweden)

João Maroco

2016-01-01

Full Text Available Abstract Student engagement is a key factor in academic achievement and degree completion, though there is much debate about the operationalization and dimensionality of this construct. The goal of this paper is to describe the development of an psycho-educational oriented measure – the University Student Engagement Inventory (USEI. This measure draws on the conceptualization of engagement as a multidimensional construct, including cognitive, behavioural and emotional engagement. Participants were 609 Portuguese University students (67 % female majoring in Social Sciences, Biological Sciences or Engineering and Exact Sciences. The content, construct and predictive validity, and reliability of the USEI were tested. The validated USEI was composed of 15 items, and supported the tri-factorial structure of student engagement. We documented evidence of adequate reliability, factorial, convergent and discriminant validities. USEI’s concurrent validity, with the Utrecht Work Engagement Scale-Student Survey, and the predictive validity for self-reported academic achievement and intention to dropout from school were also observed.

Motivation and treatment engagement intervention trial (MotivaTe-IT: the effects of motivation feedback to clinicians on treatment engagement in patients with severe mental illness

Directory of Open Access Journals (Sweden)

Jochems Eline C

2012-11-01

Full Text Available Abstract Background Treatment disengagement and non-completion poses a major problem for the successful treatment of patients with severe mental illness. Motivation for treatment has long been proposed as a major determinant of treatment engagement, but exact mechanisms remain unclear. This current study serves three purposes: 1 to determine whether a feedback intervention based on the patients’ motivation for treatment is effective at improving treatment engagement (TE of severe mentally ill patients in outpatient psychiatric treatment, 2 to gather insight into motivational processes and possible mechanisms regarding treatment motivation (TM and TE in this patient population and 3 to determine which of three theories of motivation is most plausible for the dynamics of TM and TE in this population. Methods/design The Motivation and Treatment Engagement Intervention Trial (MotivaTe-IT is a multi-center cluster randomized trial investigating the effectiveness of feedback generated by clinicians regarding their patients’ treatment motivation upon the patients’ TE. The primary outcome is the patients’ TE. Secondary outcomes are TM, psychosocial functioning and quality of life. Patients whose clinicians generate monthly motivation feedback (additional to treatment as usual will be compared to patients who receive treatment as usual. An estimated 350 patients, aged 18 to 65 years, with psychotic disorders and/or severe personality disorders will be recruited from outpatient community mental health care. The randomization will be performed by a computerized randomization program, with an allocation ratio of 1:1 (team vs. team or clinician vs. clinician and patients, but not clinicians, will be blind to treatment allocation at baseline assessment. Due to the nature of the trial, follow-up assessment can not be blinded. Discussion The current study can provide important insights regarding motivational processes and the way in which motivation

Motivation and treatment engagement intervention trial (MotivaTe-IT): the effects of motivation feedback to clinicians on treatment engagement in patients with severe mental illness.

Science.gov (United States)

Jochems, Eline C; Mulder, Cornelis L; van Dam, Arno; Duivenvoorden, Hugo J; Scheffer, Sylvia C M; van der Spek, Willem; van der Feltz-Cornelis, Christina M

2012-11-24

Treatment disengagement and non-completion poses a major problem for the successful treatment of patients with severe mental illness. Motivation for treatment has long been proposed as a major determinant of treatment engagement, but exact mechanisms remain unclear. This current study serves three purposes: 1) to determine whether a feedback intervention based on the patients' motivation for treatment is effective at improving treatment engagement (TE) of severe mentally ill patients in outpatient psychiatric treatment, 2) to gather insight into motivational processes and possible mechanisms regarding treatment motivation (TM) and TE in this patient population and 3) to determine which of three theories of motivation is most plausible for the dynamics of TM and TE in this population. The Motivation and Treatment Engagement Intervention Trial (MotivaTe-IT) is a multi-center cluster randomized trial investigating the effectiveness of feedback generated by clinicians regarding their patients' treatment motivation upon the patients' TE. The primary outcome is the patients' TE. Secondary outcomes are TM, psychosocial functioning and quality of life. Patients whose clinicians generate monthly motivation feedback (additional to treatment as usual) will be compared to patients who receive treatment as usual. An estimated 350 patients, aged 18 to 65 years, with psychotic disorders and/or severe personality disorders will be recruited from outpatient community mental health care. The randomization will be performed by a computerized randomization program, with an allocation ratio of 1:1 (team vs. team or clinician vs. clinician) and patients, but not clinicians, will be blind to treatment allocation at baseline assessment. Due to the nature of the trial, follow-up assessment can not be blinded. The current study can provide important insights regarding motivational processes and the way in which motivation influences the treatment engagement and clinical outcomes. The

Motivation and treatment engagement intervention trial (MotivaTe-IT): the effects of motivation feedback to clinicians on treatment engagement in patients with severe mental illness

Science.gov (United States)

2012-01-01

Background Treatment disengagement and non-completion poses a major problem for the successful treatment of patients with severe mental illness. Motivation for treatment has long been proposed as a major determinant of treatment engagement, but exact mechanisms remain unclear. This current study serves three purposes: 1) to determine whether a feedback intervention based on the patients’ motivation for treatment is effective at improving treatment engagement (TE) of severe mentally ill patients in outpatient psychiatric treatment, 2) to gather insight into motivational processes and possible mechanisms regarding treatment motivation (TM) and TE in this patient population and 3) to determine which of three theories of motivation is most plausible for the dynamics of TM and TE in this population. Methods/design The Motivation and Treatment Engagement Intervention Trial (MotivaTe-IT) is a multi-center cluster randomized trial investigating the effectiveness of feedback generated by clinicians regarding their patients’ treatment motivation upon the patients’ TE. The primary outcome is the patients’ TE. Secondary outcomes are TM, psychosocial functioning and quality of life. Patients whose clinicians generate monthly motivation feedback (additional to treatment as usual) will be compared to patients who receive treatment as usual. An estimated 350 patients, aged 18 to 65 years, with psychotic disorders and/or severe personality disorders will be recruited from outpatient community mental health care. The randomization will be performed by a computerized randomization program, with an allocation ratio of 1:1 (team vs. team or clinician vs. clinician) and patients, but not clinicians, will be blind to treatment allocation at baseline assessment. Due to the nature of the trial, follow-up assessment can not be blinded. Discussion The current study can provide important insights regarding motivational processes and the way in which motivation influences the treatment

Relationship quality and student engagement

Science.gov (United States)

Culver, Jennifer

The purpose of this study was to examine the qualities of support, relatedness, and negative interaction within parent-child and teacher-student relationships and their association with cognitive, psychological, and behavioral engagement. Additionally, this study explored the contributions of cognitive and psychological engagement on behavioral engagement. The role of gender, grade, and ethnicity on relationship quality and engagement was also considered. Participants (n=311) were students in grades three through five from a suburban school district in southeastern Michigan. Perceptions of teacher-student relationship quality varied by grade level. In general, younger students reported greater teacher support and relatedness in comparison to older students. Conversely, older students perceived greater conflict within the teacher-student relationship. Student engagement also varied by grade level, with younger students reporting greater engagement than older students. Ethnicity also contributed to variance in student engagement, with African American students reporting significantly more engagement than Caucasian or Multiracial students. Teacher-student relationship quality was a significant predictor of student engagement, even after controlling for student characteristics and parent-child relationship variables. Results of path analysis revealed that cognitive and psychological engagement contributed significantly to behavioral engagement.

Simple One-Dimensional Quantum-Mechanical Model for a Particle Attached to a Surface

Science.gov (United States)

Fernandez, Francisco M.

2010-01-01

We present a simple one-dimensional quantum-mechanical model for a particle attached to a surface. It leads to the Schrodinger equation for a harmonic oscillator bounded on one side that we solve in terms of Weber functions and discuss the behaviour of the eigenvalues and eigenfunctions. We derive the virial theorem and other exact relationships…

Engaging Scientists and Users in Climate Change Research and Results

Science.gov (United States)

Cloyd, E. T.; Reeves, K.; Shimamoto, M. M.; Zerbonne, S.

2016-12-01

The U.S. Global Change Research Program has a mandate to "consult with actual and potential users of the results of the program" in developing products that will support learning about and responding to climate change. USGCRP has sought to engage stakeholders throughout the development and dissemination of key products, such as the Third National Climate Assessment (NCA3, 2014) and the Climate and Health Assessment (CHA, 2016), in the strategic planning processes leading to the National Global Change Research Plan (2012) and Update to the Strategic Plan (2016), and through regular postings to social media that highlight research results and opportunities for engagement. Overall, USGCRP seeks to promote dialogue between scientific experts, stakeholders, and decision makers about information needs in regions or sectors, the potential impacts of climate change, and possible responses. This presentation will describe how USGCRP has implemented various stakeholder engagement measures during the planning, development, and release of products such as NCA3 and CHA. Through repeated opportunities for stakeholder input, USGCRP has promoted process transparency and inclusiveness in the framing of assessments and other products. In addition, USGCRP has supported scientists' engagement with a range of audiences and potential collaborators through a variety of mechanisms, including community-based meetings, deliberative forums, and identification of non-Federal speaking and knowledge co-production opportunities. We will discuss key lessons learned and successful approaches for engaging users as well as opportunities and challenges for future engagement.

Formation and Mechanism of Superhydrophobic/Hydrophobic Surfaces Made from Amphiphiles through Droplet-Mediated Evaporation-Induced Self-Assembly.

Science.gov (United States)

Dong, Fangyuan; Zhang, Mi; Tang, Wai-Wa; Wang, Yi

2015-04-23

Superhydrophobic/hydrophobic surfaces have attracted wide attention because of their broad applications in various regions, including coating, textile, packaging, electronic devices, and bioengineering. Many studies have been focused on the fabrication of superhydrophobic/hydrophobic surfaces using natural materials. In this paper, superhydrophobic/hydrophobic surfaces were formed by an amphiphilic natural protein, zein, using electrospinning. Water contact angle (WCA) and scanning electron microscopy (SEM) were used to characterize the hydrophobicity and surface morphology of the electrospun structures. The highest WCA of the zein electrospun surfaces could reach 155.5 ± 1.4°. To further understand the mechanism of superhydrophobic surface formation from amphiphiles using electrospinning, a synthetic amphiphilic polymer was selected, and also, a method similar to electrospinning, spray drying, was tried. The electrospun amphiphilic polymer surface showed a high hydrophobicity with a WCA of 141.4 ± 0.7°. WCA of the spray-dried zein surface could reach 125.3 ± 2.1°. The secondary structures of the zein in the electrospun film and cast-dried film were studied using ATR-FTIR, showing that α-helix to β-sheet transformation happened during the solvent evaporation in the cast drying process but not in the electrospinning process. A formation mechanism was proposed on the basis of the orientation of the amphiphiles during the solvent evaporation of different fabrication methods. The droplet-based or jet-based evaporation during electrospinning and spray drying led to the formation of the superhydrophobic/hydrophobic surface by the accumulation of the hydrophobic groups of the amphiphiles on the surface, while the surface-based evaporation during cast drying led to the formation of the hydrophilic surface by the accumulation of the hydrophilic groups of the amphiphiles on the surface.

Understanding the mechanisms of solid-water reactions through analysis of surface topography.

Science.gov (United States)

Bandstra, Joel Z; Brantley, Susan L

2015-12-01

The topography of a reactive surface contains information about the reactions that form or modify the surface and, therefore, it should be possible to characterize reactivity using topography parameters such as surface area, roughness, or fractal dimension. As a test of this idea, we consider a two-dimensional (2D) lattice model for crystal dissolution and examine a suite of topography parameters to determine which may be useful for predicting rates and mechanisms of dissolution. The model is based on the assumption that the reactivity of a surface site decreases with the number of nearest neighbors. We show that the steady-state surface topography in our model system is a function of, at most, two variables: the ratio of the rate of loss of sites with two neighbors versus three neighbors (d(2)/d(3)) and the ratio of the rate of loss of sites with one neighbor versus three neighbors (d(1)/d(3)). This means that relative rates can be determined from two parameters characterizing the topography of a surface provided that the two parameters are independent of one another. It also means that absolute rates cannot be determined from measurements of surface topography alone. To identify independent sets of topography parameters, we simulated surfaces from a broad range of d(1)/d(3) and d(2)/d(3) and computed a suite of common topography parameters for each surface. Our results indicate that the fractal dimension D and the average spacing between steps, E[s], can serve to uniquely determine d(1)/d(3) and d(2)/d(3) provided that sufficiently strong correlations exist between the steps. Sufficiently strong correlations exist in our model system when D>1.5 (which corresponds to D>2.5 for real 3D reactive surfaces). When steps are uncorrelated, surface topography becomes independent of step retreat rate and D is equal to 1.5. Under these conditions, measures of surface topography are not independent and any single topography parameter contains all of the available mechanistic

The Relationship Between Engagement and Neurophysiological Measures of Attention in Motion-Controlled Video Games: A Randomized Controlled Trial.

Science.gov (United States)

Leiker, Amber M; Miller, Matthew; Brewer, Lauren; Nelson, Monica; Siow, Maria; Lohse, Keith

2016-04-21

Video games and virtual environments continue to be the subject of research in health sciences for their capacity to augment practice through user engagement. Creating game mechanics that increase user engagement may have indirect benefits on learning (ie, engaged learners are likely to practice more) and may also have direct benefits on learning (ie, for a fixed amount of practice, engaged learners show superior retention of information or skills). To manipulate engagement through the aesthetic features of a motion-controlled video game and measure engagement's influence on learning. A group of 40 right-handed participants played the game under two different conditions (game condition or sterile condition). The mechanics of the game and the amount of practice were constant. During practice, event-related potentials (ERPs) to task-irrelevant probe tones were recorded during practice as an index of participants' attentional reserve. Participants returned for retention and transfer testing one week later. Although both groups improved in the task, there was no difference in the amount of learning between the game and sterile groups, countering previous research. A new finding was a statistically significant relationship between self-reported engagement and the amplitude of the early-P3a (eP3a) component of the ERP waveform, such that participants who reported higher levels of engagement showed a smaller eP3a (beta=-.08, P=.02). This finding provides physiological data showing that engagement elicits increased information processing (reducing attentional reserve), which yields new insight into engagement and its underlying neurophysiological properties. Future studies may objectively index engagement by quantifying ERPs (specifically the eP3a) to task-irrelevant probes.

Different growth mechanisms of Ge by Stranski-Krastanow on Si (111) and (001) surfaces: An STM study

Energy Technology Data Exchange (ETDEWEB)

Teys, S.A., E-mail: teys@isp.nsc.ru

2017-01-15

Highlights: • Different atomic mechanisms of transition from two-dimensional to three-dimensional-layer growth on Sransky-Krastanov observed. • The transition from 2D–3D Ge growth on Si (111) and (001) is very different. • Various changes in morphology, surface structures and sequence Ge redistribution during the growth shown. • The sequence of appearance of different incorporation places of Ge atoms was shown. - Abstract: Structural and morphological features of the wetting layer formation and the transition to the three-dimensional Ge growth on (111) and (100) Si surfaces under quasi-equilibrium growth conditions were studied by means of scanning tunneling microscopy. The mechanism of the transition from the wetting layer to the three-dimensional Ge growth on Si was demonstrated. The principal differences and general trends of the atomic processes involved in the wetting layers formation on substrates with different orientations were demonstrated. The Ge growth is accompanied by the Ge atom redistribution and partial strain relaxation due to the formation of new surfaces, vacancies and surface structures of a decreased density. The analysis of three-dimensional Ge islands sites nucleation of after the wetting layer formation was carried out on the (111) surface. The transition to the three-dimensional growth at the Si(100) surface begins with single {105} facets nucleation on the rough Ge(100) surface.

Different growth mechanisms of Ge by Stranski-Krastanow on Si (111) and (001) surfaces: An STM study

International Nuclear Information System (INIS)

Teys, S.A.

2017-01-01

Highlights: • Different atomic mechanisms of transition from two-dimensional to three-dimensional-layer growth on Sransky-Krastanov observed. • The transition from 2D–3D Ge growth on Si (111) and (001) is very different. • Various changes in morphology, surface structures and sequence Ge redistribution during the growth shown. • The sequence of appearance of different incorporation places of Ge atoms was shown. - Abstract: Structural and morphological features of the wetting layer formation and the transition to the three-dimensional Ge growth on (111) and (100) Si surfaces under quasi-equilibrium growth conditions were studied by means of scanning tunneling microscopy. The mechanism of the transition from the wetting layer to the three-dimensional Ge growth on Si was demonstrated. The principal differences and general trends of the atomic processes involved in the wetting layers formation on substrates with different orientations were demonstrated. The Ge growth is accompanied by the Ge atom redistribution and partial strain relaxation due to the formation of new surfaces, vacancies and surface structures of a decreased density. The analysis of three-dimensional Ge islands sites nucleation of after the wetting layer formation was carried out on the (111) surface. The transition to the three-dimensional growth at the Si(100) surface begins with single {105} facets nucleation on the rough Ge(100) surface.

Effects of bio-functionalizing surface treatments on the mechanical behavior of open porous titanium biomaterials.

Science.gov (United States)

Amin Yavari, S; Ahmadi, S M; van der Stok, J; Wauthle, R; Riemslag, A C; Janssen, M; Schrooten, J; Weinans, H; Zadpoor, A A

2014-08-01

Bio-functionalizing surface treatments are often applied for improving the bioactivity of biomaterials that are based on otherwise bioinert titanium alloys. When applied on highly porous titanium alloy structures intended for orthopedic bone regeneration purposes, such surface treatments could significantly change the static and fatigue properties of these structures and, thus, affect the application of the biomaterial as bone substitute. Therefore, the interplay between biofunctionalizing surface treatments and mechanical behavior needs to be controlled. In this paper, we studied the effects of two bio-functionalizing surface treatments, namely alkali-acid heat treatment (AlAcH) and acid-alkali (AcAl), on the static and fatigue properties of three different highly porous titanium alloy implants manufactured using selective laser melting. It was found that AlAcH treatment results in minimal mass loss. The static and fatigue properties of AlAcH specimens were therefore not much different from as-manufactured (AsM) specimens. In contrast, AcAl resulted in substantial mass loss and also in significantly less static and fatigue properties particularly for porous structures with the highest porosity. The ratio of the static mechanical properties of AcAl specimens to that of AsM specimen was in the range of 1.5-6. The fatigue lives of AcAl specimens were much more severely affected by the applied surface treatments with fatigue lives up to 23 times smaller than that of AsM specimens particularly for the porous structures with the highest porosity. In conclusion, the fatigue properties of surface treated porous titanium are dependent not only on the type of applied surface treatment but also on the porosity of the biomaterial. Copyright © 2014 Elsevier Ltd. All rights reserved.

Evaluation of Mechanical Property of Carbon Fiber/Polypropylene Composite According to Carbon Fiber Surface Treatment

International Nuclear Information System (INIS)

Han, Song Hee; Oh, Hyun Ju; Kim, Seong Su

2013-01-01

In this study, the mechanical properties of a carbon fiber/polypropylene composite were evaluated according to the carbon fiber surface treatment. Carbon fiber surface treatments such as silane coupling agents and plasma treatment were performed to enhance the interfacial strength between carbon fibers and polypropylene. The treated carbon fiber surface was characterized by XP S, Sem, and single-filament tensile test. The interlaminar shear strength (Ilks) of the composite with respect to the surface treatment was determined by a short beam shear test. The test results showed that the Ilks of the plasma-treated specimen increased with the treatment time. The Ilks of the specimen treated with a silane coupling agent after plasma treatment increased by 48.7% compared to that of the untreated specimen

Computer-aided study of key factors determining high mechanical properties of nanostructured surface layers in metal-ceramic composites

Science.gov (United States)

Konovalenko, Igor S.; Shilko, Evgeny V.; Ovcharenko, Vladimir E.; Psakhie, Sergey G.

2017-12-01

The paper presents the movable cellular automaton method. It is based on numerical models of surface layers of the metal-ceramic composite NiCr-TiC modified under electron beam irradiation in inert gas plasmas. The models take into account different geometric, concentration and mechanical parameters of ceramic and metallic components. The authors study the contributions of key structural factors in mechanical properties of surface layers and determine the ranges of their variations by providing the optimum balance of strength, strain hardening and fracture toughness.

Geophysicists' views about public engagement

Science.gov (United States)

Besley, J. C.; Dudo, A.; Yuan, S.

2016-12-01

The proposed talk would present the results of 2016 survey of American Geophysical Union members (n = 2040) about public engagement. This survey took place as part of a broader, NSF funded, study of engagement views across eight different U.S.-based scientific societies. The presentation would include data about geophysicists' past engagement behavior and willingness to engage alongside data about engagement attitudes, perceived norms (i.e. beliefs about whether peers engage and value engagement), and perceived efficacy (i.e., scientists' beliefs about their own communication skills and the impact of engagement). The presentation would also include results that describe scientists' overall goals for engagement (e.g., increasing support for specific policy positions, changing citizen behavior, etc.), as well as their communication-specific objectives (e.g., increasing knowledge, increase excitement, etc.). All of the results would be put in the context of equivalent results from scientists from seven other societies across a variety of fields, including chemistry, biology, and the social sciences. Three themes that would be emphasized in the presentation include (1) the fact that there are substantial commonalities in engagement views across scientific fields, (2) the important role that perceived engagement skill (efficacy) appears to play in predicting engagement willingness, and (3) a lack of evidence that scientists are thinking about engagement in strategic ways. Strategic engagement, in this regard, would involve setting clear goals and then choosing activities that the social science of science communication suggests might allow one to achieve those goals. The presentation would conclude with thoughts about what might be done to improve the effectiveness of science communication training.

The release of nickel from orthodontic NiTi wires is increased by dynamic mechanical loading but not constrained by surface nitridation.

Science.gov (United States)

Peitsch, T; Klocke, A; Kahl-Nieke, B; Prymak, O; Epple, M

2007-09-01

The influence of dynamic mechanical loading and of surface nitridation on the nickel release from superelastic nickel-titanium orthodontic wires was investigated under ultrapure conditions. Commercially available superelastic NiTi arch wires (size 0.018 x 0.025'') without surface modification (Neo Sentalloy) and with nitrogen ion implantation surface treatment (Neo Sentalloy Ionguard) were analyzed. Mechanical loading of wire segments with a force similar to the physiological situation was performed with a frequency of 5 Hz in ultrapure water and saline solution, respectively. The release of nickel was monitored by atomic absorption spectroscopy for up to 36 days. The mechanically loaded wires released significantly more nickel ( approximately 45 ng cm(-2) d(-1)) than did nonloaded wires (<1 ng cm(-2) d(-1)). There was no statistically significant effect of the testing solution (water or NaCl) or of the surface nitridation. The total amount of released nickel was small in all cases, but may nevertheless account for the occasional clinical observations of adverse reactions during application of NiTi-based orthodontic appliances. The surface nitridation did not constrain the release of nickel from NiTi under continuous mechanical stress.

Radiation exposure dose on persons engaged in radiation-related industries in Korea

International Nuclear Information System (INIS)

Lim, Bong Sik

2006-01-01

This study investigated the status of radiation exposure doses since the establishment of the 'Regulations on Safety Management of Diagnostic Radiation Generation Device' in January 6, 1995. The level of radiation exposure in people engaged or having been engaged in radiation-related industries of inspection organizations, educational organization, military units, hospitals, public health centers, businesses, research organizations or clinics over a 5 year period from Jan. 1, 2000 to Dec. 31, 2004 was measured. The 149,205 measurement data of 57,136 workers registered in a measurement organization were analysed in this study. Frequency analysis, a Chi-square test, Chi-square trend test, and ANOVA was used for data analysis. Among 57,136 men were 40,870 (71.5%). 50.3% of them were radiologic technologists, otherwise medical doctors (22.7%), nurse (2.9%) and others (24.1%). The average of depth radiation and surface radiation during the 5-year period were found to decrease each year. Both the depth radiation and surface radiation exposure were significantly higher in males, in older age groups, in radiological technologists of occupation. The departments of nuclear medicine had the highest exposure of both depth and surface radiation of the divisions of labor. There were 1.98 and 2.57 per 1,000 person-year were exposed more than 20 mSv (limit recommended by International Commission on Radiological Protection) in depth and surface radiation consequently. The total exposure per worker was significantly decreased by year. But Careful awareness is needed for the workers who exposed over 20 mSv per year. In order to minimize exposure to radiation, each person engaged in a radiation-related industry must adhere to the individual safety management guidelines more thoroughly. In addition, systematic education and continuous guidance aimed at increasing the awareness of safety must be provided

Socially responsible investment engagement

NARCIS (Netherlands)

Goessling, T.; Buijter, Bas; Freeman, R.E.; Kujala, J.; Sachs, S.

2017-01-01

This study explores engagement in socially responsible investment (SRI) processes. More specifically, it researches the impact of shareholder salience on the success of engagement activities. The research question asks: What is the relationship between shareholder salience and engagement effort

Moist Orographic Convection: Physical Mechanisms and Links to Surface-Exchange Processes

Directory of Open Access Journals (Sweden)

Daniel J. Kirshbaum

2018-02-01

Full Text Available This paper reviews the current understanding of moist orographic convection and its regulation by surface-exchange processes. Such convection tends to develop when and where moist instability coincides with sufficient terrain-induced ascent to locally overcome convective inhibition. The terrain-induced ascent can be owing to mechanical (airflow over or around an obstacle and/or thermal (differential heating over sloping terrain forcing. For the former, the location of convective initiation depends on the dynamical flow regime. In “unblocked” flows that ascend the barrier, the convection tends to initiate over the windward slopes, while in “blocked” flows that detour around the barrier, the convection tends to initiate upstream and/or downstream of the high terrain where impinging flows split and rejoin, respectively. Processes that destabilize the upstream flow for mechanically forced moist convection include large-scale moistening and ascent, positive surface sensible and latent heat fluxes, and differential advection in baroclinic zones. For thermally forced flows, convective initiation is driven by thermally direct circulations with sharp updrafts over or downwind of the mountain crest (daytime or foot (nighttime. Along with the larger-scale background flow, local evapotranspiration and transport of moisture, as well as thermodynamic heterogeneities over the complex terrain, regulate moist instability in such events. Longstanding limitations in the quantitative understanding of related processes, including both convective preconditioning and initiation, must be overcome to improve the prediction of this convection, and its collective effects, in weather and climate models.

Physical fracture properties (fracture surfaces as information sources; crackgrowth and fracture mechanisms; exemples of cracks)

International Nuclear Information System (INIS)

Meny, Lucienne.

1979-06-01

Fracture surfaces are considered as a useful source of informations: an introduction to fractography is presented; the fracture surface may be observed through X ray microanalysis, and other physical methods such as Auger electron spectroscopy or secundary ion emission. The mechanisms of macroscopic and microscopic crackgrowth and fracture are described, in the case of unstable fracture (cleavage, ductile with shear, intergranular brittleness) and of progressive crack propagation (creep, fatigue). Exemples of cracks are presented in the last chapter [fr

Effect of conditioner load on the polishing pad surface during chemical mechanical planarization process

Energy Technology Data Exchange (ETDEWEB)

Shin, Cheol Min; Qin, Hong Yi; Hong, Seok Jun; Jeon, Sang Hyuk; Kulkarni, Atul; Kim, Tae Sun [Sungkyunkwan University, Suwon (Korea, Republic of)

2016-12-15

During the Chemical mechanical planarization (CMP), the pad conditioning process can affect the pad surface characteristics. Among many CMP process parameters, the improper applied load on the conditioner arm may have adverse effects on the polyurethane pad. In this work, we evaluated the pad surface properties under the various conditioner arm applied during pad conditioning process. The conditioning pads were evaluated for surface topography, surface roughness parameters such as Rt and Rvk and Material removal rate (MRR) and within-wafer non-uniformity after wafer polishing. We observed that, the pad asperities were collapsed in the direction of conditioner rotation and blocks the pad pores applied conditioner load. The Rvk value and MRR were founded to be in relation with 4 > 1 > 7 kgF conditioner load. Hence, this study shows that, 4 kgF applied load by conditioner is most suitable for the pad conditioning during CMP.

Quantum mechanics capacitance molecular mechanics modeling of core-electron binding energies of methanol and methyl nitrite on Ag(111) surface.

Science.gov (United States)

Löytynoja, T; Li, X; Jänkälä, K; Rinkevicius, Z; Ågren, H

2016-07-14

We study a newly devised quantum mechanics capacitance molecular mechanics (QMCMM) method for the calculation of core-electron binding energies in the case of molecules adsorbed on metal surfaces. This yet untested methodology is applied to systems with monolayer of methanol/methyl nitrite on an Ag(111) surface at 100 K temperature. It was found out that the studied C, N, and O 1s core-hole energies converge very slowly as a function of the radius of the metallic cluster, which was ascribed to build up of positive charge on the edge of the Ag slab. Further analysis revealed that an extrapolation process can be used to obtain binding energies that deviated less than 0.5 eV against experiments, except in the case of methanol O 1s where the difference was as large as 1.8 eV. Additional QM-cluster calculations suggest that the latter error can be connected to the lack of charge transfer over the QM-CMM boundary. Thus, the results indicate that the QMCMM and QM-cluster methods can complement each other in a holistic picture of molecule-adsorbate core-ionization studies, where all types of intermolecular interactions are considered.

Effect of a surface oxide-dispersion-strengthened layer on mechanical strength of zircaloy-4 tubes

Directory of Open Access Journals (Sweden)

Yang-Il Jung

2018-03-01

Full Text Available An oxide-dispersion-strengthened (ODS layer was formed on Zircaloy-4 tubes by a laser beam scanning process to increase mechanical strength. Laser beam was used to scan the yttrium oxide (Y2O3–coated Zircaloy-4 tube to induce the penetration of Y2O3 particles into Zircaloy-4. Laser surface treatment resulted in the formation of an ODS layer as well as microstructural phase transformation at the surface of the tube. The mechanical strength of Zircaloy-4 increased with the formation of the ODS layer. The ring-tensile strength of Zircaloy-4 increased from 790 to 870 MPa at room temperature, from 500 to 575 MPa at 380°C, and from 385 to 470 MPa at 500°C. Strengthening became more effective as the test temperature increased. It was noted that brittle fracture occurred at room temperature, which was not observed at elevated temperatures. Resistance to dynamic high-temperature bursting improved. The burst temperature increased from 760 to 830°C at a heating rate of 5°C/s and internal pressure of 8.3 MPa. The burst opening was also smaller than those in fresh Zircaloy-4 tubes. This method is expected to enhance the safety of Zr fuel cladding tubes owing to the improvement of their mechanical properties. Keywords: Laser Surface Treatment, Microstructure, Oxide Dispersion Strengthened Alloy, Tensile Strength, Zirconium Alloy

Mechanism of drag reduction for circular cylinders with patterned surface

International Nuclear Information System (INIS)

Butt, U.; Jehring, L.; Egbers, C.

2014-01-01

Highlights: • Reduced drag of patterned cylinders over a wide range of Re numbers. • Hexagonal patterns cannot be characterized as roughness structures. • Hexagonal bumps affect the flow like spherical dimples of smaller k/d ratio do. • Main separation is delayed caused by a partial separation. • Angle of a separation line is not constant over the length of cylinder. -- Abstract: In this paper, the flow over cylinders with a patterned surface (k/d = 1.98 × 10 −2 ) is investigated in a subsonic wind tunnel over Reynolds numbers ranging from 3.14 × 10 4 to 2.77 × 10 5 by measuring drag, flow visualization and measuring velocity profiles above the surface of the cylinders, to observe the effect of hexagonal patterns on the flow of air. These patterns can also be referred as hexagonal dimples or bumps depending on their configuration. The investigations revealed that a patterned cylinder with patterns pressed outwards has a drag coefficient of about 0.65 times of a smooth one. Flow visualization techniques including surface oil-film technique and velocity profile measurement were employed to elucidate this effect, and hence present the mechanism of drag reduction. The measurement of velocity profiles using hot-wire anemometry above the surface reveal that a hexagonal bump cause local separation generating large turbulence intensity along the separating shear layer. Due to this increased turbulence, the flow reattaches to the surface with higher momentum and become able to withstand the pressure gradient delaying the main separation significantly. Besides that, the separation does not appear to occur in a straight line along the length of the cylinder as in case of most passive drag control methods, but follow exactly the hexagonal patterns forming a wave with its crest at 115° and trough at 110°, in contrast to the laminar separation line at 85° for a smooth cylinder

PERARES: Public Engagement with Research and Research Engagement with Society

NARCIS (Netherlands)

Steinhaus, Norbert; Mulder, Henk A.J.

2014-01-01

PERARES is a four-year project funded by the European Community's Seventh Framework Programme which started in 2010. The acronym stands for "Public Engagement with Research and Research Engagement with Society”. The project brings together Science Shops, Civil Society Organisations (CSOs) and

Experimental study of micro-milling mechanism and surface quality of a nickel-based single crystal superalloy

Energy Technology Data Exchange (ETDEWEB)

Gao, Qi; Gong, Yadong; Zhou, Yun Guang; Wen, Xue Long [School of Mechanical Engineering and Automation, Northeastern University, Shenyang (China)

2017-01-15

Micro-milling is widely used as a method for machining of micro-parts with high precision and efficiency. Taking the nickel-based single-crystal superalloy DD98 as the research object, the crystal characteristics of single-crystal materials were analysed, and the removal mechanism of single-crystal micro-milled parts was described. Based on molecular dynamics, a simulation model for nickel-based single-crystal superalloy DD98 micro-milling was established. Based on the response surface method of central composite design, the influences of spindle speed, feed rate, and milling depth on the surface roughness were examined, and a second-order regression model of the DD98 surface roughness was established. Using analysis of variance and the residuals of the model, a significant influence on surface roughness was found in the following order from large to small: Feed rate, spindle speed, and milling depth. Comparisons were conducted between the micro-milling experimental values and the predicted model values for different process parameters. The results show that the model fit is relatively high, and the adaptability is good. Scanning electron microscopy analysis of the micro-milling surfaces was performed to verify the slip and the removal mechanism of single-crystal materials. These results offer a theoretical reference and experimental basis for micro-milling of single-crystal materials.

Effect of surface loading on the hydro-mechanical response of a tunnel in saturated ground

Directory of Open Access Journals (Sweden)

Simon Heru Prassetyo

2016-09-01

Full Text Available The design of underground spaces in urban areas must account not only for the current overburden load but also for future surface loads, such as from construction of high-rise buildings above underground structures. In saturated ground, the surface load will generate an additional mechanical response through stress changes and ground displacement, as well as a hydraulic response through pore pressure changes. These hydro-mechanical (H-M changes can severely influence tunnel stability. This paper examines the effect of surface loading on the H-M response of a typical horseshoe-shaped tunnel in saturated ground. Two tunnel models were created in the computer code Fast Lagrangian Analysis of Continua (FLAC. One model represented weak and low permeability ground (stiff clay, and the other represented strong and high permeability ground (weathered granite. Each of the models was run under two liner permeabilities: permeable and impermeable. Two main cases were compared. In Case 1, the surface load was applied 10 years after tunnel construction. In Case 2, the surface load was applied after the steady state pore pressure condition was achieved. The simulation results show that tunnels with impermeable liners experienced the most severe influence from the surface loading, with high pore pressures, large inward displacement around the tunnels, and high bending moments in the liner. In addition, the severity of the response increased toward steady state. This induced H-M response was worse for tunnels in clay than for those in granite. Furthermore, the long-term liner stabilities in Case 1 and Case 2 were similar, indicating that the influence of the length of time between when the tunnel was completed and when the surface load was applied was negligible. These findings suggest that under surface loading, in addition to the ground strength, tunnel stability in saturated ground is largely influenced by liner permeability and the long-term H-M response of

Experimental study of microstructure changes due to low cycle fatigue of a steel nanocrystallised by Surface Mechanical Attrition Treatment (SMAT)

Energy Technology Data Exchange (ETDEWEB)

Sun, Z. [ICD, P2MN, LASMIS, University of Technology of Troyes, UMR 6281, CNRS, Troyes (France); Retraint, D., E-mail: delphine.retraint@utt.fr [ICD, P2MN, LASMIS, University of Technology of Troyes, UMR 6281, CNRS, Troyes (France); Baudin, T.; Helbert, A.L.; Brisset, F. [ICMMO, Univ Paris-Sud, Université Paris-Saclay, UMR CNRS 8182, 91405 Orsay Cedex (France); Chemkhi, M.; Zhou, J. [ICD, P2MN, LASMIS, University of Technology of Troyes, UMR 6281, CNRS, Troyes (France); Kanouté, P. [ICD, P2MN, LASMIS, University of Technology of Troyes, UMR 6281, CNRS, Troyes (France); ONERA, The French Aerospace Lab, 29 avenue de la Division Leclerc, 92322 Chatillon Cedex (France)

2017-02-15

Electron Backscatter Diffraction technique is used to characterize the microstructure of 316L steel generated by Surface Mechanical Attrition Treatment (SMAT) before and after low cycle fatigue tests. A grain size gradient is generated from the top surface to the interior of the samples after SMAT so that three main regions can be distinguished below the treated surface: (i) the ultra-fine grain area within 5 μm under the top surface with preferably oriented grains, (ii) the intermediate area where the original grains are partially transformed, and (iii) the edge periphery area where the original grains are just mechanically deformed with the presence of plastic slips. Fatigue tests show that cyclic loading does not change the grain orientation spread and does not activate any plastic slip in the ultra-fine grain top surface area induced by SMAT. On the opposite, in the plastically SMAT affected region including the intermediate area and the edge periphery area, new slip systems are activated by low cycle fatigue while the grain orientation spread is increased. These results represent a first very interesting step towards the characterization and understanding of mechanical mechanisms involved during the fatigue of a grain size gradient material. - Highlights: •LCF tests are carried out on specimens processed by SMAT. •EBSD is used to investigate microstructural changes induced by LCF. •A grain size gradient is generated by SMAT from surface to the bulk of the fatigue samples. •New slip systems are activated by LCF and GOS is increased in plastically deformed region. •However, these phenomena are not observed in the top surface ultra-fine grain area.

Experimental study of microstructure changes due to low cycle fatigue of a steel nanocrystallised by Surface Mechanical Attrition Treatment (SMAT)

International Nuclear Information System (INIS)

Sun, Z.; Retraint, D.; Baudin, T.; Helbert, A.L.; Brisset, F.; Chemkhi, M.; Zhou, J.; Kanouté, P.

2017-01-01

Electron Backscatter Diffraction technique is used to characterize the microstructure of 316L steel generated by Surface Mechanical Attrition Treatment (SMAT) before and after low cycle fatigue tests. A grain size gradient is generated from the top surface to the interior of the samples after SMAT so that three main regions can be distinguished below the treated surface: (i) the ultra-fine grain area within 5 μm under the top surface with preferably oriented grains, (ii) the intermediate area where the original grains are partially transformed, and (iii) the edge periphery area where the original grains are just mechanically deformed with the presence of plastic slips. Fatigue tests show that cyclic loading does not change the grain orientation spread and does not activate any plastic slip in the ultra-fine grain top surface area induced by SMAT. On the opposite, in the plastically SMAT affected region including the intermediate area and the edge periphery area, new slip systems are activated by low cycle fatigue while the grain orientation spread is increased. These results represent a first very interesting step towards the characterization and understanding of mechanical mechanisms involved during the fatigue of a grain size gradient material. - Highlights: •LCF tests are carried out on specimens processed by SMAT. •EBSD is used to investigate microstructural changes induced by LCF. •A grain size gradient is generated by SMAT from surface to the bulk of the fatigue samples. •New slip systems are activated by LCF and GOS is increased in plastically deformed region. •However, these phenomena are not observed in the top surface ultra-fine grain area.

Influence of surface mechanical activation of the X40Cr13 steel on roughness after ion and gas nitriding

International Nuclear Information System (INIS)

Jasinski, J.; Wojtal, A.; Jeziorski, L.; Radecki, A.; Ucieklak, S.

2003-01-01

The article describes the problem of the thermal and mechanical activation of the surface of the X40Cr13 steel on the state of the ion and gas nitriding. in order to determine the nitriding influence and make the analysis of results, the steel was subjected to: soft annealing, hardening with subsequent tempering at T = 550 o C and also mechanical activation of the surface consisting in peripheral grinding with abrasive papers of the grain size 60, 360, 1000 and mechanical polishing. The main aim of this work was to establish the influence of different surface geometrical structure, depending on X40Cr13 steel structure, on the roughness profile after ion and gas nitriding. With regard to the above, the examinations of basic roughness parameters prior to and after thermochemical processes and the analysis of utilitarian usefulness of activations applied were carried out. (author)

Promoting Discussion in Peer Instruction: Discussion Partner Assignment and Accountability Scoring Mechanisms

Science.gov (United States)

Chou, Chih-Yueh; Lin, Pin-Hsun

2015-01-01

Peer instruction (PI) involves students answering questions and peer discussion learning activities. PI can enhance student performance and engagement in classroom instruction. However, some students do not engage in the discussions. This study proposes two mechanisms, discussion partner assignment and accountability scoring mechanisms, to form…

Anxiety type modulates immediate versus delayed engagement of attention-related brain regions.

Science.gov (United States)

Spielberg, Jeffrey M; De Leon, Angeline A; Bredemeier, Keith; Heller, Wendy; Engels, Anna S; Warren, Stacie L; Crocker, Laura D; Sutton, Bradley P; Miller, Gregory A

2013-09-01

Background Habituation of the fear response, critical for the treatment of anxiety, is inconsistently observed during exposure to threatening stimuli. One potential explanation for this inconsistency is differential attentional engagement with negatively valenced stimuli as a function of anxiety type. Methods The present study tested this hypothesis by examining patterns of neural habituation associated with anxious arousal, characterized by panic symptoms and immediate engagement with negatively valenced stimuli, versus anxious apprehension, characterized by engagement in worry to distract from negatively valenced stimuli. Results As predicted, the two anxiety types evidenced distinct patterns of attentional engagement. Anxious arousal was associated with immediate activation in attention-related brain regions that habituated over time, whereas anxious apprehension was associated with delayed activation in attention-related brain regions that occurred only after habituation in a worry-related brain region. Conclusions Results further elucidate mechanisms involved in attention to negatively valenced stimuli and indicate that anxiety is a heterogeneous construct with regard to attention to such stimuli.

Students Engaged in Learning

Science.gov (United States)

Ismail, Emad A.; Groccia, James E.

2018-01-01

Engaging students in learning is a basic principle of effective undergraduate education. Outcomes of engaging students include meaningful learning experiences and enhanced skills in all learning domains. This chapter reviews the influence of engaging students in different forms of active learning on cognitive, psychomotor, and affective skill…

Dangers of the endgame: Engaging Russia and Ukraine during the gap

Energy Technology Data Exchange (ETDEWEB)

Korppoo, Anna; Gassan-zade, Olga

2011-07-01

In the absence of functional carbon market opportunities, the approaching gap in the international climate regime beyond 2012 is likely to alienate the major transition economy emitters Russia and Ukraine from the potential future climate regime. The new carbon market mechanisms currently under negotiation remain too underdeveloped and uncertain to provide incentives for Russia and Ukraine to remain actively engaged. Further, experiences with carbon market mechanisms thus far illustrate many weaknesses in the administrative and political systems of these countries which discourage their involvement in complex future mechanisms. In the absence of post-2012 carbon market options it seems likely that Ukraine will attempt to preserve its carbon market capacity by establishing a domestic ETS - however, without external involvement and prospects of demand, this may not be successful. Given Moscow's negative attitude towards further Kyoto commitments, it would be easy for Russia to interpret a gap as a broken promise: the surplus of AAUs and the Kyoto mechanisms are considered as a right that Russia was promised in Kyoto in 1997. Given the functionality of Joint Implementation (JI), its extension seems the most feasible option for engaging Russia and Ukraine in the international climate regime immediately post-2012. However, various politically difficult questions remain as to the JISC recommendation to base ERU issuance on the first commitment period AAUs. Regardless of the problems and frustrations experienced with JI and GIS during the first commitment period, engaging Russia and Ukraine in the climate regime through the continuation of JI would probably provide the least-effort option for the future. Allowing domestic carbon-market capacities to disintegrate during the gap years would probably lead to serious problems when the support of these countries is sought for the future climate regime, due not least to Russia's confrontational approach to

Study the bonding mechanism of binders on hydroxyapatite surface and mechanical properties for 3DP fabrication bone scaffolds.

Science.gov (United States)

Wei, Qinghua; Wang, Yanen; Li, Xinpei; Yang, Mingming; Chai, Weihong; Wang, Kai; zhang, Yingfeng

2016-04-01

In 3DP fabricating artificial bone scaffolds process, the interaction mechanism between binder and bioceramics power determines the microstructure and macro mechanical properties of Hydroxyapatite (HA) bone scaffold. In this study, we applied Molecular Dynamics (MD) methods to investigating the bonding mechanism and essence of binders on the HA crystallographic planes for 3DP fabrication bone scaffolds. The cohesive energy densities of binders and the binding energies, PCFs g(r), mechanical properties of binder/HA interaction models were analyzed through the MD simulation. Additionally, we prepared the HA bone scaffold specimens with different glues by 3DP additive manufacturing, and tested their mechanical properties by the electronic universal testing machine. The simulation results revealed that the relationship of the binding energies between binders and HA surface is consistent with the cohesive energy densities of binders, which is PAM/HA>PVA/HA>PVP/HA. The PCFs g(r) indicated that their interfacial interactions mainly attribute to the ionic bonds and hydrogen bonds which formed between the polar atoms, functional groups in binder polymer and the Ca, -OH in HA. The results of mechanical experiments verified the relationship of Young׳s modulus for three interaction models in simulation, which is PVA/HA>PAM/HA>PVP/HA. But the trend of compressive strength is PAM/HA>PVA/HA>PVP/HA, this is consistent with the binding energies of simulation. Therefore, the Young׳s modulus of bone scaffolds are limited by the Young׳s modulus of binders, and the compressive strength is mainly decided by the viscosity of binder. Finally, the major reasons for differences in mechanical properties between simulation and experiment were found, the space among HA pellets and the incomplete infiltration of glue were the main reasons influencing the mechanical properties of 3DP fabrication HA bone scaffolds. These results provide useful information in choosing binder for 3DP fabrication

Improving employee productivity through work engagement: Evidence from higher education sector

Directory of Open Access Journals (Sweden)

Jalal Hanaysha

2016-01-01

Full Text Available Employee productivity is one of the important management topics that received significant research attentions from several scholars and considered as a primary mechanism to enhance organizational success. Knowing what are the key factors that influence productivity is vital to ensure long term performance. This study examines the effect of work engagement on employee productivity in higher education sector. To accomplish this purpose, the primary data using survey instrument were collected from a sample of 242 employees at public universities in northern Malaysia using an online survey method. The collected data was analyzed using SPSS and Structural equation modelling on AMOS. The results indicated that work engagement had significant positive effect on employee productivity. Moreover, this study provides an evidence that all of the dimensions of work engagement namely vigor, dedication, and absorption have significant positive effects on employee productivity.

Influence of Surface Coating of Magnetic Nanoparticles on Mechanical Properties of Polymer Nanocomposites

Science.gov (United States)

Yarar, Ecem; Karakas, Gizem; Rende, Deniz; Ozisik, Rahmi; Malta, Seyda

Polymer nanocomposites have emerged as promising materials due to improved properties when compared with conventional bulk polymers. Nanofillers are natural or synthetic organic/inorganic particles that are less than 100 nm in at least one dimension. Even the addition of trace amounts of nanofillers to polymers may lad to unique combinations of properties. Among variety of inorganic nanofillers, iron oxide magnetic nanoparticles are of great interest due to their unique physical and chemical properties, such as low toxicity, biocompatibility, large magnetization and conductivity, owing to their extremely small size and large specific surface area. In this study, approximately 8-10 nm magnetic nanoparticles coated with either citric acid or oleic acid are synthesized and blended with poly(methyl methacrylate) (PMMA) or poly(ethylene oxide) (PEO). The hydrophobicity/hydrophillicity of the polymer and the surface coating on the iron oxide nanoparticles are exploited to control the dispersion state of nanoparticles, and the effect of dispersion on mechanical and thermal properties of the nanocomposite are investigated via experimental methods such as dynamic mechanical analysis and differential scanning calorimetry. This material is based upon work partially supported by the National Science Foundation under Grant No. CMMI-1538730 and TUBITAK 112M666.

Comparing the effects of mechanical perturbation training with a compliant surface and manual perturbation training on joints kinematics after ACL-rupture.

Science.gov (United States)

Nawasreh, Zakariya; Failla, Mathew; Marmon, Adam; Logerstedt, David; Snyder-Mackler, Lynn

2018-05-23

Performing physical activities on a compliant surface alters joint kinematics and increases joints stiffness. However, the effect of compliant surface on joint kinematics after ACL-rupture is yet unknown. To compare the effects of mechanical perturbation training with a compliant surface to manual perturbation training on joint kinematics after ACL-rupture. Sixteen level I/II athletes with ACL-rupture participated in this preliminary study. Eight patients received mechanical perturbation with compliant surface (Mechanical) and 8 patients received manual perturbation training (Manual). Patients completed standard gait analysis before (Pre) and after (Post) training. Significant group-by-time interactions were found for knee flexion angle at initial contact (IC) and peak knee flexion (PKF) (pMechanical:27.68+4.08°, p = 0.011), hip rotation angle at PKE (Manual:-3.40+4.78°, Mechanical:5.43+4.78°, p Mechanical:0.55+2.23°, p = 0.039). Main effects of time were found for hip adduction angle at PKE (Pre:6.98+4.48°, Post:8.41+4.91°, p = 0.04), knee adduction angle at IC (Pre:-2.90+3.50°, Post:-0.62+2.58°, p = 0.03), ankle adduction angle at IC (Pre:2.16+3.54, Post:3.8+3.68, p = 0.008), and ankle flexion angle at PKF (Pre:-4.55+2.77°, Post:-2.39+3.48°, p = 0.01). Training on a compliant surface induces different effects on joint kinematics compared to manual perturbation training after ACL-rupture. Manual perturbation improved hip alignment and increased knee flexion angles, while mechanical training decreased knee flexion angles throughout the stance phase. Administering training on a compliant surface after ACL-rupture may help improving dynamic knee stability, however, long-term effects on knee health needs to be determined. Copyright © 2018 Elsevier B.V. All rights reserved.

Effects of the different frequencies and loads of ultrasonic surface rolling on surface mechanical properties and fretting wear resistance of HIP Ti–6Al–4V alloy

Energy Technology Data Exchange (ETDEWEB)

Li, G., E-mail: ligang_scut@outlook.com; Qu, S.G., E-mail: qusg@scut.edu.cn; Pan, Y.X.; Li, X.Q.

2016-12-15

Highlights: • Effects of MUSR frequency and load on surface properties of HIP Ti-6Al-4V investigated. • The grains in surface-modified layer were refined and appeared twins and many dense dislocations. • The hardened layer depth and surface residual stress of MUSR- treated samples were significantly improved. • MUSR- treated samples showed the good fretting friction and wear resistance. • The best microstructure and properties of surface-modified layer obtained by sample treated by 30 kHz and 900 N. - Abstract: The main purpose of this paper was to investigate the effects of the different frequencies and loads of multi-pass ultrasonic surface rolling (MUSR) on surface layer mechanical properties, microstructure and fretting friction and wear characteristics of HIP (hot isostatic pressing) Ti–6Al–4 V alloy. Some microscopic analysis methods (SEM, TEM and EDS) were used to characterize the modified surface layer of material after MUSR treatment. The results indicated that the material in sample surface layer experienced a certain extent plastic deformation, and accompanied by some dense dislocations and twins generation. Moreover surface microhardness and residual stress of samples treated by MUSR were also greatly improved compared with the untreated. The fretting friction and wear properties of samples treated by MUSR in different conditions are tested at 10 and 15 N in dry friction conditions. It could be found that friction coefficient and wear volume loss were significantly declined in the optimal result. The main wear mechanism of MUSR-treated samples included abrasive wear, adhesion and spalling.

Student Engagement in Assessments: What Students and Teachers Find Engaging

Science.gov (United States)

Bae, Soung; Kokka, Kari

2016-01-01

Although research has shown that student engagement is strongly related to performance on assessment tasks, especially for traditionally underserved subgroups of students, increasing student engagement has not been the goal of standardized tests of content knowledge. Recent state and federal policies, however, are changing the assessment…

Mechanisms of Surface Antigenic Variation in the Human Pathogenic Fungus Pneumocystis jirovecii.

Science.gov (United States)

Schmid-Siegert, Emanuel; Richard, Sophie; Luraschi, Amanda; Mühlethaler, Konrad; Pagni, Marco; Hauser, Philippe M

2017-11-07

Microbial pathogens commonly escape the human immune system by varying surface proteins. We investigated the mechanisms used for that purpose by Pneumocystis jirovecii This uncultivable fungus is an obligate pulmonary pathogen that in immunocompromised individuals causes pneumonia, a major life-threatening infection. Long-read PacBio sequencing was used to assemble a core of subtelomeres of a single P. jirovecii strain from a bronchoalveolar lavage fluid specimen from a single patient. A total of 113 genes encoding surface proteins were identified, including 28 pseudogenes. These genes formed a subtelomeric gene superfamily, which included five families encoding adhesive glycosylphosphatidylinositol (GPI)-anchored glycoproteins and one family encoding excreted glycoproteins. Numerical analyses suggested that diversification of the glycoproteins relies on mosaic genes created by ectopic recombination and occurs only within each family. DNA motifs suggested that all genes are expressed independently, except those of the family encoding the most abundant surface glycoproteins, which are subject to mutually exclusive expression. PCR analyses showed that exchange of the expressed gene of the latter family occurs frequently, possibly favored by the location of the genes proximal to the telomere because this allows concomitant telomere exchange. Our observations suggest that (i) the P. jirovecii cell surface is made of a complex mixture of different surface proteins, with a majority of a single isoform of the most abundant glycoprotein, (ii) genetic mosaicism within each family ensures variation of the glycoproteins, and (iii) the strategy of the fungus consists of the continuous production of new subpopulations composed of cells that are antigenically different. IMPORTANCE Pneumocystis jirovecii is a fungus causing severe pneumonia in immunocompromised individuals. It is the second most frequent life-threatening invasive fungal infection. We have studied the mechanisms

The Synapse Project: Engagement in mentally challenging activities enhances neural efficiency.

Science.gov (United States)

McDonough, Ian M; Haber, Sara; Bischof, Gérard N; Park, Denise C

2015-01-01

Correlational and limited experimental evidence suggests that an engaged lifestyle is associated with the maintenance of cognitive vitality in old age. However, the mechanisms underlying these engagement effects are poorly understood. We hypothesized that mental effort underlies engagement effects and used fMRI to examine the impact of high-challenge activities (digital photography and quilting) compared with low-challenge activities (socializing or performing low-challenge cognitive tasks) on neural function at pretest, posttest, and one year after the engagement program. In the scanner, participants performed a semantic-classification task with two levels of difficulty to assess the modulation of brain activity in response to task demands. The High-Challenge group, but not the Low-Challenge group, showed increased modulation of brain activity in medial frontal, lateral temporal, and parietal cortex-regions associated with attention and semantic processing-some of which were maintained a year later. This increased modulation stemmed from decreases in brain activity during the easy condition for the High-Challenge group and was associated with time committed to the program, age, and cognition. Sustained engagement in cognitively demanding activities facilitated cognition by increasing neural efficiency. Mentally-challenging activities may be neuroprotective and an important element to maintaining a healthy brain into late adulthood.

Experiments in engagement: Designing public engagement with science and technology for capacity building.

Science.gov (United States)

Selin, Cynthia; Rawlings, Kelly Campbell; de Ridder-Vignone, Kathryn; Sadowski, Jathan; Altamirano Allende, Carlo; Gano, Gretchen; Davies, Sarah R; Guston, David H

2017-08-01

Public engagement with science and technology is now widely used in science policy and communication. Touted as a means of enhancing democratic discussion of science and technology, analysis of public engagement with science and technology has shown that it is often weakly tied to scientific governance. In this article, we suggest that the notion of capacity building might be a way of reframing the democratic potential of public engagement with science and technology activities. Drawing on literatures from public policy and administration, we outline how public engagement with science and technology might build citizen capacity, before using the notion of capacity building to develop five principles for the design of public engagement with science and technology. We demonstrate the use of these principles through a discussion of the development and realization of the pilot for a large-scale public engagement with science and technology activity, the Futurescape City Tours, which was carried out in Arizona in 2012.

Transnational television audiences and modes of engagement: studying audience engagement as a set of experiences

DEFF Research Database (Denmark)

Keinonen, Heidi; Jensen, Pia Majbritt; Esser, Andrea

2018-01-01

Audience engagement is attracting increasing attention in various academic disciplines. Recently, the industry- and technology-oriented conceptualizations of engagement have been challenged by a more audience-oriented understanding. This article aims at contributing to the development of a more...... nuanced audience-oriented approach. First, we make a theoretical argument by bringing various key theories together and, second, we present an empirical contribution by analysing audience engagement as a set of experiences. Our analysis builds on the empirical material produced by conducting two rounds...... and ritualistic engagement, ludic engagement. We also discovered that audiences at times get disengaged or opt to actively resist engagement....

Measuring patient engagement: development and psychometric properties of the Patient Health Engagement (PHE) Scale.

Science.gov (United States)

Graffigna, Guendalina; Barello, Serena; Bonanomi, Andrea; Lozza, Edoardo

2015-01-01

Beyond the rhetorical call for increasing patients' engagement, policy makers recognize the urgency to have an evidence-based measure of patients' engagement and capture its effect when planning and implementing initiatives aimed at sustaining the engagement of consumers in their health. In this paper, authors describe the Patient Health Engagement Scale (PHE-scale), a measure of patient engagement that is grounded in rigorous conceptualization and appropriate psychometric methods. The scale was developed based on our previous conceptualization of patient engagement (the PHE-model). In particular, the items of the PHE-scale were developed based on the findings from the literature review and from interviews with chronic patients. Initial psychometric analysis was performed to pilot test a preliminary version of the items. The items were then refined and administered to a national sample of chronic patients (N = 382) to assess the measure's psychometric performance. A final phase of test-retest reliability was performed. The analysis showed that the PHE Scale has good psychometric properties with good correlation with concurrent measures and solid reliability. Having a valid and reliable measure to assess patient engagement is the first step in understanding patient engagement and its role in health care quality, outcomes, and cost containment. The PHE Scale shows a promising clinical relevance, indicating that it can be used to tailor intervention and assess changes after patient engagement interventions.

Measuring Student Engagement in the Online Course: The Online Student Engagement Scale (OSE)

Science.gov (United States)

Dixson, Marcia D.

2015-01-01

Student engagement is critical to student learning, especially in the online environment, where students can often feel isolated and disconnected. Therefore, teachers and researchers need to be able to measure student engagement. This study provides validation of the Online Student Engagement scale (OSE) by correlating student self-reports of…

Constituting Public Engagement

DEFF Research Database (Denmark)

Davies, Sarah Rachael

2013-01-01

understanding of science to those of public engagement with science and technology (PEST), and the histories, or genealogies, of such models. Data from two qualitative studies-a case study of one of the United Kingdom'ssix Beacons for Public Engagement and a study of contract research staff-are used......This article uses data from two U.K. studies in order to explore the meanings attached to public engagement. It focuses on two issues of importance to contemporary discussions of science communication: the degree to which there has been a smooth transition, in practice, from models of public...... to characterize the ways in which U.K. academic communities understand PEST. It is argued that engagement is construed as multiple, relational, and outcomes oriented, with seven key outcomes ranging from better research to empowered individuals. These differences are traced to personal and professional...

Measuring user engagement

CERN Document Server

Lalmas, Mounia; Yom-Tov, Elad

2014-01-01

User engagement refers to the quality of the user experience that emphasizes the positive aspects of interacting with an online application and, in particular, the desire to use that application longer and repeatedly. User engagement is a key concept in the design of online applications (whether for desktop, tablet or mobile), motivated by the observation that successful applications are not just used, but are engaged with. Users invest time, attention, and emotion in their use of technology, and seek to satisfy pragmatic and hedonic needs. Measurement is critical for evaluating whether online

Effect of machining parameters on surface integrity of silicon carbide ceramic using end electric discharge milling and mechanical grinding hybrid machining

International Nuclear Information System (INIS)

Ji, Renjie; Liu, Yonghong; Zhang, Yanzhen; Cai, Baoping; Li, Xiaopeng; Zheng, Chao

2013-01-01

A novel hybrid process that integrates end electric discharge (ED) milling and mechanical grinding is proposed. The process is able to effectively machine a large surface area on SiC ceramic with good surface quality and fine working environmental practice. The polarity, pulse on-time, and peak current are varied to explore their effects on the surface integrity, such as surface morphology, surface roughness, micro-cracks, and composition on the machined surface. The results show that positive tool polarity, short pulse on-time, and low peak current cause a fine surface finish. During the hybrid machining of SiC ceramic, the material is mainly removed by end ED milling at rough machining mode, whereas it is mainly removed by mechanical grinding at finish machining mode. Moreover, the material from the tool can transfer to the workpiece, and a combination reaction takes place during machining.

Contact angle hysteresis on doubly periodic smooth rough surfaces in Wenzel's regime: The role of the contact line depinning mechanism.

Science.gov (United States)

Iliev, Stanimir; Pesheva, Nina; Iliev, Pavel

2018-04-01

We report here on the contact angle hysteresis, appearing when a liquid meniscus is in contact with doubly sinusoidal wavelike patterned surfaces in Wenzel's wetting regime. Using the full capillary model we obtain numerically the contact angle hysteresis as a function of the surface roughness factor and the equilibrium contact angle for a block case and a kink case contact line depinning mechanism. We find that the dependencies of the contact angle hysteresis on the surface roughness factor are different for the different contact line depinning mechanisms. These dependencies are different also for the two types of rough surfaces we studied. The relations between advancing, receding, and equilibrium contact angles are investigated. A comparison with the existing asymptotical, numerical, and experimental results is carried out.

Reaction Mechanisms on Multiwell Potential Energy Surfaces in Combustion (and Atmospheric) Chemistry

International Nuclear Information System (INIS)

Osborn, David L.

2017-01-01

Chemical reactions occurring on a potential energy surface with multiple wells are ubiquitous in low temperature combustion and the oxidation of volatile organic compounds in earth’s atmosphere. The rich variety of structural isomerizations that compete with collisional stabilization make characterizing such complex-forming reactions challenging. This review describes recent experimental and theoretical advances that deliver increasingly complete views of their reaction mechanisms. New methods for creating reactive intermediates coupled with multiplexed measurements provide many experimental observables simultaneously. Automated methods to explore potential energy surfaces can uncover hidden reactive pathways, while master equation methods enable a holistic treatment of both sequential and well-skipping pathways. Our ability to probe and understand nonequilibrium effects and reaction sequences is increasing. These advances provide the fundamental science base for predictive models of combustion and the atmosphere that are crucial to address global challenges.

Reaction Mechanisms on Multiwell Potential Energy Surfaces in Combustion (and Atmospheric) Chemistry

Science.gov (United States)

Osborn, David L.

2017-05-01

Chemical reactions occurring on a potential energy surface with multiple wells are ubiquitous in low-temperature combustion and in the oxidation of volatile organic compounds in Earth's atmosphere. The rich variety of structural isomerizations that compete with collisional stabilization makes characterizing such complex-forming reactions challenging. This review describes recent experimental and theoretical advances that deliver increasingly complete views of their reaction mechanisms. New methods for creating reactive intermediates coupled with multiplexed measurements provide many experimental observables simultaneously. Automated methods to explore potential energy surfaces can uncover hidden reactive pathways, and master equation methods enable a holistic treatment of both sequential and well-skipping pathways. Our ability to probe and understand nonequilibrium effects and reaction sequences is increasing. These advances provide the fundamental science base for predictive models of combustion and the atmosphere that are crucial to address global challenges.

Facile fabrication of superhydrophobic surface with excellent mechanical abrasion and corrosion resistance on copper substrate by a novel method.

Science.gov (United States)

Su, Fenghua; Yao, Kai

2014-06-11

A novel method for controllable fabrication of a superhydrophobic surface with a water contact angle of 162 ± 1° and a sliding angle of 3 ± 0.5° on copper substrate is reported in this Research Article. The facile and low-cost fabrication process is composed from the electrodeposition in traditional Watts bath and the heat-treatment in the presence of (heptadecafluoro-1,1,2,2-tetradecyl) triethoxysilane (AC-FAS). The superhydrophobicity of the fabricated surface results from its pine-cone-like hierarchical micro-nanostructure and the assembly of low-surface-energy fluorinated components on it. The superhydrophobic surface exhibits high microhardness and excellent mechanical abrasion resistance because it maintains superhydrophobicity after mechanical abrasion against 800 grit SiC sandpaper for 1.0 m at the applied pressure of 4.80 kPa. Moreover, the superhydrophobic surface has good chemical stability in both acidic and alkaline environments. The potentiodynamic polarization and electrochemical impedance spectroscopy test shows that the as-prepared superhydrophobic surface has excellent corrosion resistance that can provide effective protection for the bare Cu substrate. In addition, the as-prepared superhydrophobic surface has self-cleaning ability. It is believed that the facile and low-cost method offer an effective strategy and promising industrial applications for fabricating superhydrophobic surfaces on various metallic materials.

Mitotic Transcriptional Activation: Clearance of Actively Engaged Pol II via Transcriptional Elongation Control in Mitosis.

Science.gov (United States)

Liang, Kaiwei; Woodfin, Ashley R; Slaughter, Brian D; Unruh, Jay R; Box, Andrew C; Rickels, Ryan A; Gao, Xin; Haug, Jeffrey S; Jaspersen, Sue L; Shilatifard, Ali

2015-11-05

Although it is established that some general transcription factors are inactivated at mitosis, many details of mitotic transcription inhibition (MTI) and its underlying mechanisms are largely unknown. We have identified mitotic transcriptional activation (MTA) as a key regulatory step to control transcription in mitosis for genes with transcriptionally engaged RNA polymerase II (Pol II) to activate and transcribe until the end of the gene to clear Pol II from mitotic chromatin, followed by global impairment of transcription reinitiation through MTI. Global nascent RNA sequencing and RNA fluorescence in situ hybridization demonstrate the existence of transcriptionally engaged Pol II in early mitosis. Both genetic and chemical inhibition of P-TEFb in mitosis lead to delays in the progression of cell division. Together, our study reveals a mechanism for MTA and MTI whereby transcriptionally engaged Pol II can progress into productive elongation and finish transcription to allow proper cellular division. Copyright © 2015 Elsevier Inc. All rights reserved.

Auger decay mechanism in photon-stimulated desorption of ions from surfaces

International Nuclear Information System (INIS)

Parks, C.C.

1983-11-01

Photon-stimulated desorption (PSD) of positive ions was studied with synchrotron radiation using an angle-integrating time-of-flight mass spectrometer. Ion yields as functions of photon energy near core levels were measured from condensed gases, alkali fluorides, and other alkali and alkaline earth halides. These results are compared to bulk photoabsorption measurements with emphasis on understanding fundamental desorption mechanisms. The applicability of the Auger decay mechanism, in which ion desorption is strictly proportional to surface absorption, is discussed in detail. The Auger decay model is developed in detail to describe Na + and F + desorption from NaF following Na(1s) excitation. The major decay pathways of the Na(1s) hole leading to desorption are described and equations for the energetics of ion desorption are developed. Ion desorption spectra of H + , Li + , and F + are compared to bulk photoabsorption near the F(2s) and Li(1s) edges of LiF. A strong photon beam exposure dependence of ion yields from alkali fluorides is revealed, which may indicate the predominance of metal ion desorption from defect sites. The large role of indirect mechanisms in ion desorption condensed N 2 -O 2 multilayers is demonstrated and discussed. Ion desorption spectra from several alkali halides and alkaline earth halides are compared to bulk photoabsorption spectra. Relative ion yields from BaF 2 and a series of alkali halides are discussed in terms of desorption mechanisms

Mechanization of drill-and-blast operations in surface mines

Energy Technology Data Exchange (ETDEWEB)

Rogan, B.

1985-07-01

Comments on recent developments in blasting techniques in modern surface mines and quarries. The tendency to use large boreholes (up to 320 mm diameter) and on site manufactured ANFO and slurry explosives is stressed. Soviet experience with ANFO and slurry explosives and with 9 types of explosive-mixing/charging vehicles is presented. One type of vehicle is used as a stable explosive mixing unit, the others (SUZN-1B, SUZN-2, SUZN-5A, SUZN-5AM, ZS-1B, MZS-1M, MAZ-509P) are used as mobile explosive mixing and loading units. Some also incorporate a borehole stemming device. Mixtures of ANFO and slurry (aquatol) explosives, explosive charging capacities (outputs 9-30 t/h) and other characteristics of mechanized explosive charging vehicles are described. Obligatory safety measures during usage are quoted. 4 refs.

The Relationship between Optimism and Engagement: The Impact on Student Performance

Science.gov (United States)

Medlin, Bobby; Faulk, Larry

2011-01-01

The concepts of optimism and employee engagement as mechanisms to improving individual performance have been discussed in the management literature. Though studies concerning optimism in the workplace are relatively limited, evidence certainly exists that links the concept to improvement in individual academic and workplace performance.…

Mechanical characterisation of surface layers by x-ray diffraction -application to tribology

International Nuclear Information System (INIS)

Farrahi, G.H.

1996-01-01

The results presented in this paper show that X-ray diffraction can be employed for the characterisation of surface layer damage through residual stresses and work hardening by some tribological actions such as fretting and dry sliding. X-ray diffraction technique can also be employed for a rapid and non-destructive measurement of hardness of hardened steel. The diffraction profile analysis can offer a good indication about the materials characteristics and the microstructural evolution caused by heat treatment or by mechanical loading

Bilateral engagement amid geopolitics: A case of India and Iran

Directory of Open Access Journals (Sweden)

Faisal Ahmed

2013-06-01

Full Text Available India’s engagement with West Asia including Iran has always been a balancing act hovering between economic necessities and strategic pursuits. The paper briefly traces the evolution of Indo-Iran engagements and also analyses their respective macroeconomic parameters. It also outlines and discusses three major geopolitical and geo-economic influences including sanctions on Iran, payment mechanism, and Iran’s business environment. Moreover, the issues pertaining to access to oil, transit route through Afghanistan and other trade facilitation measures have also been discussed. The paper also uses the revealed comparative advantage index to identify some potential areas of cooperation. Also, it argues that India needs to be more cautious and pragmatic in its strategic endeavours.

Formation mechanism of a silane-PVA/PVAc complex film on a glass fiber surface.

Science.gov (United States)

Repovsky, Daniel; Jane, Eduard; Palszegi, Tibor; Slobodnik, Marek; Velic, Dusan

2013-10-21

Mechanical properties of glass fiber reinforced composite materials are affected by fiber sizing. A complex film formation, based on a silane film and PVA/PVAc (polyvinyl alcohol/polyvinyl acetate) microspheres on a glass fiber surface is determined at 1) the nanoscale by using atomic force microscopy (AFM), and 2) the macroscale by using the zeta potential. Silane groups strongly bind through the Si-O-Si bond to the glass surface, which provides the attachment mechanism as a coupling agent. The silane groups form islands, a homogeneous film, as well as empty sites. The average roughness of the silanized surface is 6.5 nm, whereas it is only 0.6 nm for the non-silanized surface. The silane film vertically penetrates in a honeycomb fashion from the glass surface through the deposited PVA/PVAc microspheres to form a hexagonal close pack structure. The silane film not only penetrates, but also deforms the PVA/PVAc microspheres from the spherical shape in a dispersion to a ellipsoidal shape on the surface with average dimensions of 300/600 nm. The surface area value Sa represents an area of PVA/PVAc microspheres that are not affected by the silane penetration. The areas are found to be 0.2, 0.08, and 0.03 μm(2) if the ellipsoid sizes are 320/570, 300/610, and 270/620 nm for silane concentrations of 0, 3.8, and 7.2 μg mL(-1), respectively. The silane film also moves PVA/PVAc microspheres in the process of complex film formation, from the low silane concentration areas to the complex film area providing enough silane groups to stabilize the structure. The values for the residual silane honeycomb structure heights (Ha ) are 6.5, 7, and 12 nm for silane concentrations of 3.8, 7.2, and 14.3 μg mL(-1), respectively. The pH-dependent zeta-potential results suggest a specific role of the silane groups with effects on the glass fiber surface and also on the PVA/PVAc microspheres. The non-silanized glass fiber surface and the silane film have similar zeta potentials ranging

First-principles study of size-, surface- and mechanical strain-dependent electronic properties of wurtzite and zinc-blende InSb nanowires

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yong [School of Mathematics, Physics and Energy Engineering, Hunan Institute of Technology, Hengyang 421002 (China); Xie, Zhong-Xiang, E-mail: xiezxhu@163.com [School of Mathematics, Physics and Energy Engineering, Hunan Institute of Technology, Hengyang 421002 (China); Yu, Xia; Wang, Hai-Bin; Deng, Yuan-Xiang [School of Mathematics, Physics and Energy Engineering, Hunan Institute of Technology, Hengyang 421002 (China); Ning, Feng, E-mail: fning@gxtc.edu.cn [College of Physics and Electronic Engineering, Guangxi Teachers Education University, Nanning 530001 (China)

2016-08-06

Using first-principle calculations with density functional theory, we investigated the modification of electronic properties in zinc-blende (ZB) and wurtzite (WZ) InSb nanowires (NWs) grown along the [111] and [0001] directions for different size, different surface coverage and different mechanical strain. The results show that before the surface passivation, ZBNWs and WZNWs exhibit the metallic character and the semiconductor character, respectively. WZNWs show a crossover from a direct to an indirect as diameter decreases. After the surface passivation, both ZBNWs and WZNWs are found to be direct-gap character. The electronic band structure shows a significant response to changes in surface passivation with pseudo hydrogen and halogen. The band structure with mechanical strain is strongly dependent on the crystal orientation and the NW diameter. In ZBNWs, compressive strain induces the indirect band gap character, whereas tensile strain can not form it. WZNWs have various strain dependence in that both compressive and tensile strain make InSb show a direct band gap character. A brief analysis of these results is given. - Highlights: • InSb nanowires with different surfaces can show the different band structures. • Band gap magnitude of InSb nanowires depends on the suppression of surface states. • Different types of mechanical strains show the different effect on the band structure of the InSb nanowires.

Game Development as Students’ Engagement Project in High School Mathematics

Directory of Open Access Journals (Sweden)

Ryan V. Dio

2015-12-01

Full Text Available The general expectancies of the enhanced basic education curriculum in the Philippines focuses on the performance standards which can be expressed when students are able to produce products as evidence that they can transfer or use their learning in real-life situations. One way to assess students achievement is through an engaging activities that would require them apply the knowledge and skills acquired in the subject as the outcome of their learning. This descriptive method of research employed content analysis procedures and survey in describing and assessing the significant feature of the mathematical games as potential learning devices developed by the high school students through an engaging task assignment. It utilized purposive sampling techniques in the selection of the respondents and the submitted write-ups of mathematical games for analysis as typical sample in this study. The study revealed that the high school students developed mathematical board games with different objectives and mechanics as inspired by their learning, experiences, hobbies, and interest. Mathematical concepts and processes along numbers and number sense, measurements, algebra, geometry, and probability and statistics were integrated in the game through question card and mechanics of the game itself. The groups of students and teachers have high level of agreement as to the workmanship and usability, mechanics and organization, relevance to instruction/learning, and fun and enjoyment of the game as revealed by their assessment from very satisfactory to excellent level. Results implied that teachers in any subject area may use students’ engagement project as teaching strategy to produce products and performance that would provide evidence of students’ learning. The school curriculum makers may consider the students’ output as subjects of research for further improvements, exhibits, and classroom utilization.

Achieving successful community engagement: a rapid realist review.

Science.gov (United States)

De Weger, E; Van Vooren, N; Luijkx, K G; Baan, C A; Drewes, H W

2018-04-13

Community engagement is increasingly seen as crucial to achieving high quality, efficient and collaborative care. However, organisations are still searching for the best and most effective ways to engage citizens in the shaping of health and care services. This review highlights the barriers and enablers for engaging communities in the planning, designing, governing, and/or delivering of health and care services on the macro or meso level. It provides policymakers and professionals with evidence-based guiding principles to implement their own effective community engagement (CE) strategies. A Rapid Realist Review was conducted to investigate how interventions interact with contexts and mechanisms to influence the effectiveness of CE. A local reference panel, consisting of health and care professionals and experts, assisted in the development of the research questions and search strategy. The panel's input helped to refine the review's findings. A systematic search of the peer-reviewed literature was conducted. Eight action-oriented guiding principles were identified: Ensure staff provide supportive and facilitative leadership to citizens based on transparency; foster a safe and trusting environment enabling citizens to provide input; ensure citizens' early involvement; share decision-making and governance control with citizens; acknowledge and address citizens' experiences of power imbalances between citizens and professionals; invest in citizens who feel they lack the skills and confidence to engage; create quick and tangible wins; take into account both citizens' and organisations' motivations. An especially important thread throughout the CE literature is the influence of power imbalances and organisations' willingness, or not, to address such imbalances. The literature suggests that 'meaningful participation' of citizens can only be achieved if organisational processes are adapted to ensure that they are inclusive, accessible and supportive of citizens.

Martensitic phase transformations in the nanostructured surface layers induced by mechanical attrition treatment

International Nuclear Information System (INIS)

Ni Zhichun; Wang Xiaowei; Wu Erdong; Liu Gang

2005-01-01

Conversion electron Moessbauer spectroscopy (CEMS) and x-ray diffraction (XRD) analysis have been used to investigate the relationship between characteristics of phase transformation and the treatment time in surface nanocrystallized 316L stainless steel induced by surface mechanical attrition treatment (SMAT). A similar trend of development of the martensitic phase upon the treatment time has been observed from both CEMS and XRD measurements. However, in the CEMS measurement, two types of martensite phase with different magnetic hyperfine fields are revealed. Based on a random distribution of the non-iron coordinating atoms, a three-element theoretical model is developed to illustrate the difference of two types of martensite phase. The calculated results indicate the segregation of the non-iron atoms associated with SMAT treatment

Enhanced charging kinetics of porous electrodes: surface conduction as a short-circuit mechanism.

Science.gov (United States)

Mirzadeh, Mohammad; Gibou, Frederic; Squires, Todd M

2014-08-29

We use direct numerical simulations of the Poisson-Nernst-Planck equations to study the charging kinetics of porous electrodes and to evaluate the predictive capabilities of effective circuit models, both linear and nonlinear. The classic transmission line theory of de Levie holds for general electrode morphologies, but only at low applied potentials. Charging dynamics are slowed appreciably at high potentials, yet not as significantly as predicted by the nonlinear transmission line model of Biesheuvel and Bazant. We identify surface conduction as a mechanism which can effectively "short circuit" the high-resistance electrolyte in the bulk of the pores, thus accelerating the charging dynamics and boosting power densities. Notably, the boost in power density holds only for electrode morphologies with continuous conducting surfaces in the charging direction.

Good, better, engaged? The effect of company-initiated customer engagement behavior on shareholder value

NARCIS (Netherlands)

Beckers, Sander F.M.; van Doorn, Jenny; Verhoef, Peter C.

In today’s connected world, customer engagement behaviors are very important. Many companies launch initiatives to stimulate customer engagement. However, despite evidence that customer engagement behavior also matters to share-holders, academic research on the firm value consequences of customer

The Effect of Laser Surface Treatment on Structure and Mechanical Properties Aluminium Alloy ENAC-AlMg9

Directory of Open Access Journals (Sweden)

Pakieła W.

2016-09-01

Full Text Available In this work, the influence of a high power diode laser surface treatment on the structure and properties of aluminium alloy has been determined. The aim of this study was to improve the mechanical and tribological properties of the surface layer of the aluminium alloy by simultaneously melting and feeding tungsten carbide particles into the molten pool. During the process was used high-power diode laser HPDL. In order to remelt the aluminium alloy surface the HPDL laser of 1.8, 2.0 and 2.2 kW laser beam power has been used. The linear laser scan rate of the beam was set 0.5 cm/s. In order to protect the liquid metal during laser treatment was used argon. As a base material was used aluminium alloy ENAC-AlMg9. To improve the surface mechanical and wear properties of the applied aluminium alloy was used biphasic tungsten carbide WC/W2C. The size of alloying powder was in the range 110-210 µm. The ceramic powder was introduced in the remelting zone by a gravity feeder at a constant rate of 8 g/m.

Thermal crackling: study of the mechanical effects of quick temperature fluctuations on metallic surfaces

International Nuclear Information System (INIS)

Pradel, P.

1984-05-01

After a brief overview of the thermohydraulical conditions of liquid sodium leading to important temperature fluctuations near the metallic surfaces, the author examines the transfer modes of these fluctuations in the structure thickness and the long term mechanical effects. Dimensioning models based on thermal and metallurgical properties are under study for structures subject to such sodium loads [fr

Impact of Gastric Acid Induced Surface Changes on Mechanical Behavior and Optical Characteristics of Dental Ceramics.

Science.gov (United States)

Kulkarni, Aditi; Rothrock, James; Thompson, Jeffery

2018-01-14

To test the impact of exposure to artificial gastric acid combined with toothbrush abrasion on the properties of dental ceramics. Earlier research has indicated that immersion in artificial gastric acid has caused increased surface roughness of dental ceramics; however, the combined effects of acid immersion and toothbrush abrasion and the impact of increased surface roughness on mechanical strength and optical properties have not been studied. Three commercially available ceramics were chosen for this study: feldspathic porcelain, lithium disilicate glass-ceramic, and monolithic zirconium oxide. The specimens (10 × 1 mm discs) were cut, thermally treated as required, and polished. Each material was divided into four groups (n = 8 per group): control (no exposure), acid only, brush only, acid + brush. The specimens were immersed in artificial gastric acid (50 ml of 0.2% [w/v] sodium chloride in 0.7% [v/v] hydrochloric acid mixed with 0.16 g of pepsin powder, pH = 2) for 2 minutes and rinsed with deionized water for 2 minutes. The procedure was repeated 6 times/day × 9 days, and specimens were stored in deionized water at 37°C. Toothbrush abrasion was performed using an ISO/ADA design brushing machine for 100 cycles/day × 9 days. The acid + brush group received both treatments. Specimens were examined under SEM and an optical microscope for morphological changes. Color and translucency were measured using spectrophotometer CIELAB coordinates (L*, a*, b*). Surface gloss was measured using a gloss meter. Surface roughness was measured using a stylus profilometer. Biaxial flexural strength was measured using a mechanical testing machine. The data were analyzed by one-way ANOVA followed by Tukey's HSD post hoc test (p gloss, and surface roughness for porcelain and e.max specimens. No statistically significant changes were found for any properties of zirconia specimens. The acid treatment affected the surface roughness, color, and gloss of porcelain and e

‘It’s Something Posh People Do’: Digital Distinction in Young People’s Cross-Media News Engagement

Directory of Open Access Journals (Sweden)

Jannie Møller Hartley

2018-05-01

Full Text Available In this article, I analyse digital distinction mechanisms in young people’s cross media engagement with news. Using a combination of open online diaries and qualitative interviews with young Danes aged 15 to 18 who differ in social background and education, and with Bourdieu’s field theory as an analytical framework, the article investigates how cultural capital (CC operates in specific tastes and distastes for news genres, platforms and providers. The article argues that distinction mechanism not only works on the level of news providers and news genres but also on the level of engagement practices—the ways in which people enact and describe their own news engagement practices. Among those rich in CC, physical, analogue objects in the form of newspapers and physical conversations about news are seen as ‘better’ that digital ones, resulting in a feeling of guilt when they mostly engage with news on social media. Secondly, young people with lower CC discard legacy news, which they see as elitist and irrelevant. Thirdly, those rich in CC are media and news genre savvy in the sense that it makes them able to critically evaluate the news they engage with across platforms and sites.

Engaged work teams in healthy companies: drivers, processes, and outcomes of team work engagement

OpenAIRE

Torrente Barberà, Pedro

2014-01-01

This PhD thesis analyses work engagement in the context of work teams taking a collective, psychosocial perspective. Throughout this thesis, the following topics will be addressed: 1) the state-of-the-art in the topic of team work engagement, 2) the measurement of team work engagement, 3) the association of team work engagement with other relevant individual-level constructs and how it fits in traditional research models in the field of Positive Occupational Health Psychology, 4) the antecede...

Corrosion mechanism of a Ni-based alloy in supercritical water: Impact of surface plastic deformation

International Nuclear Information System (INIS)

Payet, Mickaël; Marchetti, Loïc; Tabarant, Michel; Chevalier, Jean-Pierre

2015-01-01

Highlights: • The dissolution of Ni and Fe cations occurs during corrosion of Ni-based alloys in SCW. • The nature of the oxide layer depends locally on the alloy microstructure. • The corrosion mechanism changes when cold-work increases leading to internal oxidation. - Abstract: Ni–Fe–Cr alloys are expected to be a candidate material for the generation IV nuclear reactors that use supercritical water at temperatures up to 600 °C and pressures of 25 MPa. The corrosion resistance of Alloy 690 in these extreme conditions was studied considering the surface finish of the alloy. The oxide scale could suffer from dissolution or from internal oxidation. The presence of a work-hardened zone reveals the competition between the selective oxidation of chromium with respect to the oxidation of nickel and iron. Finally, corrosion mechanisms for Ni based alloys are proposed considering the effects of plastically deformed surfaces and the dissolution.

Nanoscale mechanical surface properties of single crystalline martensitic Ni-Mn-Ga ferromagnetic shape memory alloys

International Nuclear Information System (INIS)

Jakob, A M; Müller, M; Rauschenbach, B; Mayr, S G

2012-01-01

Located beyond the resolution limit of nanoindentation, contact resonance atomic force microscopy (CR-AFM) is employed for nano-mechanical surface characterization of single crystalline 14M modulated martensitic Ni-Mn-Ga (NMG) thin films grown by magnetron sputter deposition on (001) MgO substrates. Comparing experimental indentation moduli-obtained with CR-AFM-with theoretical predictions based on density functional theory (DFT) indicates the central role of pseudo plasticity and inter-martensitic phase transitions. Spatially highly resolved mechanical imaging enables the visualization of twin boundaries and allows for the assessment of their impact on mechanical behavior at the nanoscale. The CR-AFM technique is also briefly reviewed. Its advantages and drawbacks are carefully addressed. (paper)

Study of the Mechanical Properties of a Nanostructured Surface Layer on 316L Stainless Steel

Directory of Open Access Journals (Sweden)

F. C. Lang

2016-01-01

Full Text Available A nanostructured surface layer (NSSL was generated on a 316L stainless steel plate through surface nanocrystallization (SNC. The grains of the surface layer were refined to nanoscale after SNC treatment. Moreover, the microstructure and mechanical properties of NSSL were analyzed with a transmission electron microscope (TEM and scanning electron microscope (SEM, through nanoindentation, and through reverse analysis of finite element method (FEM. TEM results showed that the grains in the NSSL measured 8 nm. In addition, these nanocrystalline grains took the form of random crystallographic orientation and were roughly equiaxed in shape. In situ SEM observations of the tensile process confirmed that the motions of the dislocations were determined from within the material and that the motions were blocked by the NSSL, thus improving overall yielding stress. Meanwhile, the nanohardness and the elastic modulus of the NSSL, as well as those of the matrix, were obtained with nanoindentation technology. The reverse analysis of FEM was conducted with MARC software, and the process of nanoindentation on the NSSL and the matrix was simulated. The plastic mechanical properties of NSSL can be derived from the simulation by comparing the results of the simulation and of actual nanoindentation.

Remote sensing of impervious surface growth: A framework for quantifying urban expansion and re-densification mechanisms

Science.gov (United States)

Shahtahmassebi, Amir Reza; Song, Jie; Zheng, Qing; Blackburn, George Alan; Wang, Ke; Huang, Ling Yan; Pan, Yi; Moore, Nathan; Shahtahmassebi, Golnaz; Sadrabadi Haghighi, Reza; Deng, Jing Song

2016-04-01

A substantial body of literature has accumulated on the topic of using remotely sensed data to map impervious surfaces which are widely recognized as an important indicator of urbanization. However, the remote sensing of impervious surface growth has not been successfully addressed. This study proposes a new framework for deriving and summarizing urban expansion and re-densification using time series of impervious surface fractions (ISFs) derived from remotely sensed imagery. This approach integrates multiple endmember spectral mixture analysis (MESMA), analysis of regression residuals, spatial statistics (Getis_Ord) and urban growth theories; hence, the framework is abbreviated as MRGU. The performance of MRGU was compared with commonly used change detection techniques in order to evaluate the effectiveness of the approach. The results suggested that the ISF regression residuals were optimal for detecting impervious surface changes while Getis_Ord was effective for mapping hotspot regions in the regression residuals image. Moreover, the MRGU outputs agreed with the mechanisms proposed in several existing urban growth theories, but importantly the outputs enable the refinement of such models by explicitly accounting for the spatial distribution of both expansion and re-densification mechanisms. Based on Landsat data, the MRGU is somewhat restricted in its ability to measure re-densification in the urban core but this may be improved through the use of higher spatial resolution satellite imagery. The paper ends with an assessment of the present gaps in remote sensing of impervious surface growth and suggests some solutions. The application of impervious surface fractions in urban change detection is a stimulating new research idea which is driving future research with new models and algorithms.

Quantum mechanical limit to plasmonic enhancement as observed by surface-enhanced Raman scattering.

Science.gov (United States)

Zhu, Wenqi; Crozier, Kenneth B

2014-10-14

Plasmonic nanostructures enable light to be concentrated into nanoscale 'hotspots', wherein the intensity of light can be enhanced by orders of magnitude. This plasmonic enhancement significantly boosts the efficiency of nanoscale light-matter interactions, enabling unique linear and nonlinear optical applications. Large enhancements are often observed within narrow gaps or at sharp tips, as predicted by the classical electromagnetic theory. Only recently has it become appreciated that quantum mechanical effects could emerge as the feature size approaches atomic length-scale. Here we experimentally demonstrate, through observations of surface-enhanced Raman scattering, that the emergence of electron tunnelling at optical frequencies limits the maximum achievable plasmonic enhancement. Such quantum mechanical effects are revealed for metallic nanostructures with gap-widths in the single-digit angstrom range by correlating each structure with its optical properties. This work furthers our understanding of quantum mechanical effects in plasmonic systems and could enable future applications of quantum plasmonics.

STM study on surface relief, ultra-fine structure and transformation mechanism of bainite in steels

International Nuclear Information System (INIS)

Fang, H.S.; Yang, Z.G.; Wang, J.J.; Zheng, Y.K.

1995-01-01

The surface reliefs accompanying lower bainite transformation in steels have been studied by scanning tunneling microscopy (STM). With the exclusive vertical resolution of STM, we observed that the surface relief associated with bainite is a group of surface reliefs related to subplates, subunits and sub-subunits. From the bainite plate to the sub-subunit in it, the reliefs are in a tent shape, not of invariant plane strain (IPS) type. The fine structure of bainite in a steel has also been shown by STM and TEM that bainite plate is composed of subplates, subunits and sub-subunits. On the basis of the fine structure inside a bainitic ferrite plate observed under STM, sympathetic-ledgewise mechanism of bainite formation is proposed. (orig.)

Quantum-mechanical interference in charge exchange between hydrogen and graphene-like surfaces

International Nuclear Information System (INIS)

Romero, M; Iglesias-García, A; Goldberg, E C

2012-01-01

The neutral to negative charge fluctuation of a hydrogen atom in front of a graphene surface is calculated by using the Anderson model within an infinite intra atomic Coulomb repulsion approximation. We perform an ab initio calculation of the Anderson hybridization function that allows investigation of the effect of quantum-mechanical interference related to the Berry phase inherent to the graphene band structure. We find that consideration of the interaction of hydrogen on top of many C atoms leads to a marked asymmetry of the imaginary part of the hybridization function with respect to the Fermi level. Consequently, Fano factors larger than one and strongly dependent on the energy around the Fermi level are predicted. Moreover, the suppression of the hybridization for energies above the Fermi level can explain the unexpected large negative ion formation measured in the scattering of protons by graphite-like surfaces. (paper)

Surface-treated commercially pure titanium for biomedical applications: Electrochemical, structural, mechanical and chemical characterizations

International Nuclear Information System (INIS)

Ogawa, Erika S.; Matos, Adaias O.; Beline, Thamara; Marques, Isabella S.V.; Sukotjo, Cortino; Mathew, Mathew T.; Rangel, Elidiane C.; Cruz, Nilson C.; Mesquita, Marcelo F.; Consani, Rafael X.

2016-01-01

Modified surfaces have improved the biological performance and biomechanical fixation of dental implants compared to machined (polished) surfaces. However, there is a lack of knowledge about the surface properties of titanium (Ti) as a function of different surface treatment. This study investigated the role of surface treatments on the electrochemical, structural, mechanical and chemical properties of commercial pure titanium (cp-Ti) under different electrolytes. Cp-Ti discs were divided into 6 groups (n = 5): machined (M—control); etched with HCl + H_2O_2 (Cl), H_2SO_4 + H_2O_2 (S); sandblasted with Al_2O_3 (Sb), Al_2O_3 followed by HCl + H_2O_2 (SbCl), and Al_2O_3 followed by H_2SO_4 + H_2O_2 (SbS). Electrochemical tests were conducted in artificial saliva (pHs 3; 6.5 and 9) and simulated body fluid (SBF—pH 7.4). All surfaces were characterized before and after corrosion tests using atomic force microscopy, scanning electron microscopy, energy dispersive microscopy, X-ray diffraction, surface roughness, Vickers microhardness and surface free energy. The results indicated that Cl group exhibited the highest polarization resistance (R_p) and the lowest capacitance (Q) and corrosion current density (I_c_o_r_r) values. Reduced corrosion stability was noted for the sandblasted groups. Acidic artificial saliva decreased the R_p values of cp-Ti surfaces and produced the highest I_c_o_r_r values. Also, the surface treatment and corrosion process influenced the surface roughness, Vickers microhardness and surface free energy. Based on these results, it can be concluded that acid-etching treatment improved the electrochemical stability of cp-Ti and all treated surfaces behaved negatively in acidic artificial saliva. - Highlights: • Characterization of surface treatment for biomedical implants was investigated. • Sandblasting reduced the corrosion stability of cp-Ti. • Acid etching is a promising dental implants surface treatment.

Surface-treated commercially pure titanium for biomedical applications: Electrochemical, structural, mechanical and chemical characterizations

Energy Technology Data Exchange (ETDEWEB)

Ogawa, Erika S.; Matos, Adaias O.; Beline, Thamara [Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas (UNICAMP), Av Limeira, 901, Piracicaba, São Paulo 13414-903 (Brazil); IBTN/Br—Institute of Biomaterials, Tribocorrosion and Nanomedicine—Brazilian Branch (Brazil); Marques, Isabella S.V. [Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas (UNICAMP), Av Limeira, 901, Piracicaba, São Paulo 13414-903 (Brazil); Sukotjo, Cortino [Department of Restorative Dentistry, University of Illinois at Chicago, College of Dentistry, 801 S Paulina, Chicago, IL, USA, 60612 (United States); IBTN—Institute of Biomaterials, Tribocorrosion and Nanomedicine (United States); Mathew, Mathew T. [IBTN—Institute of Biomaterials, Tribocorrosion and Nanomedicine (United States); Department of Biomedical Sciences, University of Illinois, College of Medicine at Rockford, 1601 Parkview Avenue, Rockford, IL, USA, 61107 (United States); Rangel, Elidiane C.; Cruz, Nilson C. [IBTN/Br—Institute of Biomaterials, Tribocorrosion and Nanomedicine—Brazilian Branch (Brazil); Laboratory of Technological Plasmas, Engineering College, Univ Estadual Paulista (UNESP), Av Três de Março, 511, Sorocaba, São Paulo 18087-180 (Brazil); Mesquita, Marcelo F.; Consani, Rafael X. [Department of Prosthodontics and Periodontology, Piracicaba Dental School, University of Campinas (UNICAMP), Av Limeira, 901, Piracicaba, São Paulo 13414-903 (Brazil); and others

2016-08-01

Modified surfaces have improved the biological performance and biomechanical fixation of dental implants compared to machined (polished) surfaces. However, there is a lack of knowledge about the surface properties of titanium (Ti) as a function of different surface treatment. This study investigated the role of surface treatments on the electrochemical, structural, mechanical and chemical properties of commercial pure titanium (cp-Ti) under different electrolytes. Cp-Ti discs were divided into 6 groups (n = 5): machined (M—control); etched with HCl + H{sub 2}O{sub 2} (Cl), H{sub 2}SO{sub 4} + H{sub 2}O{sub 2} (S); sandblasted with Al{sub 2}O{sub 3} (Sb), Al{sub 2}O{sub 3} followed by HCl + H{sub 2}O{sub 2} (SbCl), and Al{sub 2}O{sub 3} followed by H{sub 2}SO{sub 4} + H{sub 2}O{sub 2} (SbS). Electrochemical tests were conducted in artificial saliva (pHs 3; 6.5 and 9) and simulated body fluid (SBF—pH 7.4). All surfaces were characterized before and after corrosion tests using atomic force microscopy, scanning electron microscopy, energy dispersive microscopy, X-ray diffraction, surface roughness, Vickers microhardness and surface free energy. The results indicated that Cl group exhibited the highest polarization resistance (R{sub p}) and the lowest capacitance (Q) and corrosion current density (I{sub corr}) values. Reduced corrosion stability was noted for the sandblasted groups. Acidic artificial saliva decreased the R{sub p} values of cp-Ti surfaces and produced the highest I{sub corr} values. Also, the surface treatment and corrosion process influenced the surface roughness, Vickers microhardness and surface free energy. Based on these results, it can be concluded that acid-etching treatment improved the electrochemical stability of cp-Ti and all treated surfaces behaved negatively in acidic artificial saliva. - Highlights: • Characterization of surface treatment for biomedical implants was investigated. • Sandblasting reduced the corrosion stability of cp

Engagement in Games: Developing an Instrument to Measure Consumer Videogame Engagement and Its Validation

Directory of Open Access Journals (Sweden)

Amir Zaib Abbasi

2017-01-01

Full Text Available The aim of the study is to develop a new instrument to measure engagement in videogame play termed as consumer videogame engagement. The study followed the scale development procedure to develop an instrument to measure the construct of consumer videogame engagement. In this study, we collected the data in two different phases comprising study 1 (n=136 and study 2 (n=270. We employed SPSS 22.0 for exploratory factor analysis using study 1 respondents to explore the factors for consumer videogame engagement and reliability analysis. Results of EFA resulted with six-factor solution. We further used SmartPLS 3.0 software on study 2 respondents to further confirm the six-factor solution as reflective measurement model on the first-order level, and three second-order formative constructs on the second-order or higher-order level as formative measurement model. Results of the reflective measurement model and formative measurement model evidenced that consumer videogame engagement has strong psychometric properties and is a valid instrument to measure engagement in videogame play. Results also confirmed that consumer videogame engagement is a multidimensional construct as well as a reflective-formative construct. The study is unique in its investigation as it develops an instrument to measure engagement in videogame play which comprises the cognitive, affective, and behavioral dimensions.

Analysis of reverse gate leakage mechanism of AlGaN/GaN HEMTs with N2 plasma surface treatment

Science.gov (United States)

Liu, Hui; Zhang, Zongjing; Luo, Weijun

2018-06-01

The mechanism of reverse gate leakage current of AlGaN/GaN HEMTs with two different surface treatment methods are studied by using C-V, temperature dependent I-V and theoretical analysis. At the lower reverse bias region (VR >- 3.5 V), the dominant leakage current mechanism of the device with N2 plasma surface treatment is the Poole-Frenkel emission current (PF), and Trap-Assisted Tunneling current (TAT) is the principal leakage current of the device which treated by HCl:H2O solution. At the higher reverse bias region (VR current of the device with N2 plasma surface treatment is one order of magnitude smaller than the device which treated by HCl:H2O solution. This is due to the recovery of Ga-N bond in N2 plasma surface treatment together with the reduction of the shallow traps in post-gate annealing (PGA) process. The measured results agree well with the theoretical calculations and demonstrate N2 plasma surface treatment can reduce the reverse leakage current of the AlGaN/GaN HEMTs.

Participatory Sustainability Approach to Value Capture-Based Urban Rail Financing in India through Deliberated Stakeholder Engagement

Directory of Open Access Journals (Sweden)

Satya Sai Kumar Jillella

2015-06-01

Full Text Available Increasingly, cities around the world are seeking innovative financial mechanisms to build rail transit projects. Land value capture (VC is a financing mechanism to fund urban rail transit. Often VC mechanisms are viewed only as a financing tool applied in relation to increased land values from the administration and legislation perspectives, without actively involving the community in the process. The lack of such participation has resulted in the under collection of the true value established. The transit beneficiary community and city tax payers are especially important stakeholders in this process as their willingness to participate is really critical to the overall VC success and transport outcome. This paper introduces a participatory sustainability approach to enable a more deliberated stakeholder engagement intervention across the VC life cycle. A four-step “Participatory Strategic Value Capture (PSVC” framework is proposed offering step-by-step guidance toward facilitating a meaningful stakeholder dialogue, deliberation, and collaboration around the stated engagement interests. The PSVC framework, applied to the proposed Bangalore sub-urban rail project in India, has demonstrated the importance of stakeholder engagement using deliberated participatory approaches from a win-win perspective.

Students individual engagement in GIS

DEFF Research Database (Denmark)

Madsen, Lene Møller; Christiansen, Frederik V; Rump, Camilla Østerberg

2014-01-01

This paper develops two sets of concepts to theorize why students engage differently in Geographical Information Systems (GIS). These theoretical concepts are used as an analytical lens to explore empirical data on the experiences and engagement of students enrolled in an undergraduate GIS course...... in planning and management. The analysis shows that both the theoretical perspectives and the custom and didactical contract are important to understand students' engagement in GIS. However, it is the personal desiderata that are the key to understanding the students' different engagement. Further, a temporal...... dimension and contextual awareness are important in understanding students' engagement in a broader perspective....

The Engagement Gap

DEFF Research Database (Denmark)

Tartari, Valentina; Salter, Ammon

2013-01-01

Recently, debate on women in academic science has been extended to academics' engagement with industry. We suggest that women tend to engage less in industry collaboration than their male colleagues of similar status. We argue that differences are mitigated by the presence of other women and by s...

The relationship between the particle properties, mechanical behavior, and surface roughness of some pharmaceutical excipient compacts

International Nuclear Information System (INIS)

Narayan, Padma; Hancock, Bruno C.

2003-01-01

Several common pharmaceutical excipient powders were compacted at a constant solid fraction (SF) in order to study the relationship between powder properties, compact surface roughness, and compact mechanical properties such as hardness, elasticity, and brittleness. The materials used in this study included microcrystalline cellulose (MCC), fumaric acid, mannitol, lactose monohydrate, spray dried lactose, sucrose, and dibasic calcium phosphate dihydrate. A slow consolidation process was used to make compacts at a SF of 0.85 (typical for most pharmaceutical tablets) from single excipient components. A model was proposed to describe the surface roughness of compacts based on the brittle or ductile deformation tendencies of the powder materials. The roughness profile would also be dependent upon the magnitude of the compression stress in relation to the yield stress (onset of irreversible deformation) values of the excipients. It was hypothesized that brittle materials would produce smooth compacts with high surface variability due to particle fracture, and the converse would apply for ductile materials. Compact surfaces should be smoother if the materials were compressed above their yield pressure values. Non-contact optical profilometry was used along with scanning electron microscopy to quantify and characterize the surface morphology of the excipient compacts. The roughness parameters R a (average roughness), R q (RMS roughness), R q /R a (ratio describing surface variability), and R sk (skewness) were found to correlate with the deformation properties of the excipients. Brittle materials such as lactose, sucrose, and calcium phosphate produced compacts with low values of R a and R q , high variability, and negative R sk . The opposite was found with plastic materials such as MCC, mannitol, and fumaric acid. The highly negative skewness values for brittle material compacts may indicate their propensity to be vulnerable to cracks or surface defects. These findings

The relationship between the particle properties, mechanical behavior, and surface roughness of some pharmaceutical excipient compacts

Energy Technology Data Exchange (ETDEWEB)

Narayan, Padma; Hancock, Bruno C

2003-08-25

Several common pharmaceutical excipient powders were compacted at a constant solid fraction (SF) in order to study the relationship between powder properties, compact surface roughness, and compact mechanical properties such as hardness, elasticity, and brittleness. The materials used in this study included microcrystalline cellulose (MCC), fumaric acid, mannitol, lactose monohydrate, spray dried lactose, sucrose, and dibasic calcium phosphate dihydrate. A slow consolidation process was used to make compacts at a SF of 0.85 (typical for most pharmaceutical tablets) from single excipient components. A model was proposed to describe the surface roughness of compacts based on the brittle or ductile deformation tendencies of the powder materials. The roughness profile would also be dependent upon the magnitude of the compression stress in relation to the yield stress (onset of irreversible deformation) values of the excipients. It was hypothesized that brittle materials would produce smooth compacts with high surface variability due to particle fracture, and the converse would apply for ductile materials. Compact surfaces should be smoother if the materials were compressed above their yield pressure values. Non-contact optical profilometry was used along with scanning electron microscopy to quantify and characterize the surface morphology of the excipient compacts. The roughness parameters R{sub a} (average roughness), R{sub q} (RMS roughness), R{sub q}/R{sub a} (ratio describing surface variability), and R{sub sk} (skewness) were found to correlate with the deformation properties of the excipients. Brittle materials such as lactose, sucrose, and calcium phosphate produced compacts with low values of R{sub a} and R{sub q}, high variability, and negative R{sub sk}. The opposite was found with plastic materials such as MCC, mannitol, and fumaric acid. The highly negative skewness values for brittle material compacts may indicate their propensity to be vulnerable to

Kinetics and mechanism of heterogeneous oxidation of sulfur dioxide by ozone on surface of calcium carbonate

Directory of Open Access Journals (Sweden)

L. Li

2006-01-01

Full Text Available Sulfate particles play a key role in the air quality and the global climate, but the heterogeneous formation mechanism of sulfates on surfaces of atmospheric particles is not well established. Carbonates, which act as a reactive component in mineral dust due to their special chemical properties, may contribute significantly to the sulfate formation by heterogeneous processes. This paper presents a study on the oxidation of SO2 by O3 on CaCO3 particles. Using Diffuse Reflectance Infrared Fourier Transform Spectroscopy (DRIFTS, the formation of sulfite and sulfate on the surface was identified, and the roles of O3 and water in oxidation processes were determined. The results showed that in the presence of O3, SO2can be oxidized to sulfate on the surface of CaCO3 particles. The reaction is first order in SO2 and zero order in O3. The reactive uptake coefficient for SO2 [(0.6–9.8×1014 molecule cm-3] oxidation by O3 [(1.2–12×1014 molecule cm-3] was determined to be (1.4±0.3×10-7 using the BET area as the reactive area and (7.7±1.6×10-4 using the geometric area. A two-stage mechanism that involves adsorption of SO2 followed by O3 oxidation is proposed and the adsorption of SO2 on the CaCO3 surface is the rate-determining step. The proposed mechanism can well explain the experiment results. The atmospheric implications were explored based on a box model calculation. It was found that the heterogeneous reaction might be an important pathway for sulfate formation in the atmosphere.

Cell-surface metalloprotease ADAM12 is internalized by a clathrin- and Grb2-dependent mechanism

DEFF Research Database (Denmark)

Hansen, Dorte Stautz; Leyme, Anthony; Grandal, Michael Vibo

2012-01-01

ADAM12 (A Disintegrin And Metalloprotease 12), a member of the ADAMs family of transmembrane proteins, is involved in ectodomain shedding, cell-adhesion and signaling, with important implications in cancer. Therefore, mechanisms that regulate the levels and activity of ADAM12 at the cell-surface ......ADAM12 (A Disintegrin And Metalloprotease 12), a member of the ADAMs family of transmembrane proteins, is involved in ectodomain shedding, cell-adhesion and signaling, with important implications in cancer. Therefore, mechanisms that regulate the levels and activity of ADAM12 at the cell...

Contributions of chemical and mechanical surface properties and temperature effect on the adhesion at the nanoscale

International Nuclear Information System (INIS)

Awada, Houssein; Noel, Olivier; Hamieh, Tayssir; Kazzi, Yolla; Brogly, Maurice

2011-01-01

The atomic force microscope (AFM) is a powerful tool to investigate surface properties of model systems at the nanoscale. However, to get semi-quantitative and reproducible data with the AFM, it is necessary to establish a rigorous experimental procedure. In particular, a systematic calibration procedure of AFM measurements is necessary before producing reliable semi-quantitative data. In this paper, we study the contributions of the chemical and mechanical surface properties or the temperature influence on the adhesion energy at a local scale. To reach this objective, two types of model systems were considered. The first one is composed of rigid substrates (silicon wafers or AFM tips covered with gold) which were chemically modified by molecular self-assembling monolayers to display different surface properties (methyl and hydroxyl functional groups). The second one consists of model polymer networks (cross-linked polydimethylsiloxane) of variable mechanical properties. The comparison of the force curves obtained from the two model systems shows that the viscoelastic contributions dominate for the adhesion with polymer substrates, whereas, chemical contributions dominate for the rigid substrates. The temperature effect on the adhesion energy is also reported. Finally, we propose a relation for the adhesion energy at the nanoscale. This relation relates the energy measured during the separation of the contact to the three parameters: the surface properties of the polymer, the energy dissipated within the contact zone and the temperature.

Indonesian Teacher Engagement Index (ITEI): An Emerging Concept of Teacher Engagement in Indonesia

Science.gov (United States)

Sasmoko; Doringin, F.; Indrianti, Y.; Goni, A. M.; Ruliana, P.

2018-02-01

This paper presents a new concept of teacher engagement in Indonesia. The various studies in this paper examine various perspectives and even criticize the initial research on teacher engagement, so as to build the concept of different teacher engagement and in accordance with the Indonesian context so that it can be implemented and has direct impact as a guideline on improving the quality of teachers and education personnel in Indonesia. The method used in this paper is the Neuroresearch research method focused on exploratory research. The conclusion of this research is the development of Indonesian Teacher Engagement Index concept (ITEI) as a concept that describes the condition of teachers who experienced various psychological conditions positively, actively participate in building positive education, able to show good performance, have supportive competence, have national character as Characteristic of Indonesia and able to show the nationalism leadership engagement.

Mechanism of equivalent electric dipole oscillation for high-order harmonic generation from grating-structured solid-surface by femtosecond laser pulse

Energy Technology Data Exchange (ETDEWEB)

Wang, Yang; Song, Hai-Ying; Liu, H.Y.; Liu, Shi-Bing, E-mail: sbliu@bjut.edu.cn

2017-07-12

Highlights: • Proposed a valid mechanism of high harmonic generation by laser grating target interaction: oscillation of equivalent electric dipole (OEED). • Found that there also exist harmonic emission at large emission angle but not just near-surface direction as the former researches had pointed out. • Show the process of the formation and motion of electron bunches at the grating-target surface irradiating with femtosecond laser pulse. - Abstract: We theoretically study high-order harmonic generation (HHG) from relativistically driven overdense plasma targets with rectangularly grating-structured surfaces by femtosecond laser pulses. Our particle-in-cell (PIC) simulations show that, under the conditions of low laser intensity and plasma density, the harmonics emit principally along small angles deviating from the target surface. Further investigation of the surface electron dynamics reveals that the electron bunches are formed by the interaction between the laser field and the target surface, giving rise to the oscillation of equivalent electric-dipole (OEED), which enhances specific harmonic orders. Our work helps understand the mechanism of harmonic emissions from grating targets and the distinction from the planar harmonic scheme.

Engagement Means Everyone

Science.gov (United States)

Patton, Carol

2012-01-01

Employee engagement is not just HR's responsibility. While HR is responsible for the process of measuring and driving engagement, improving it is actually everyone's responsibility. And that means reducing the barriers to productivity to drive business performance. Training departments can play a pivotal role. Their job is to enhance curriculum or…

Workaholism, work engagement and work-home outcomes: exploring the mediating role of positive and negative emotions.

Science.gov (United States)

Clark, Malissa A; Michel, Jesse S; Stevens, Gregory W; Howell, Julia W; Scruggs, Ross S

2014-10-01

This study examines the mechanisms through which workaholism and work engagement impact work-home conflict and enrichment, respectively. Specifically, we examine the mediating role of positive and negative emotions (e.g. joviality and guilt) in the relationship between workaholism, work engagement and work-home outcomes. Results, based on a sample of 340 working adults participating in a two-wave study, indicate that negative emotions-particularly anxiety, anger and disappointment-mediate the relationship between workaholism and work-home conflict and positive emotions-particularly joviality and self-assurance-mediate the relationship between work engagement and work-home enrichment. These results provide further evidence that workaholism and work engagement are related to distinct sets of emotional variables and disparate work and home outcomes. Copyright © 2013 John Wiley & Sons, Ltd.

Microstructure and mechanical behavior of pulsed laser surface melted AISI D2 cold work tool steel

Science.gov (United States)

Yasavol, N.; Abdollah-zadeh, A.; Ganjali, M.; Alidokht, S. A.

2013-01-01

D2 cold work tool steel (CWTS) was subjected to pulse laser surface melting (PLSM) at constant frequency of 20 Hz Nd: YAG laser with different energies, scanning rate and pulse durations radiated to the surface. Characterizing the PLSM, with optical and field emission scanning electron microscopy, electron backscattered diffraction and surface hardness mapping technique was used to evaluate the microhardness and mechanical behavior of different regions of melting pool. Increasing laser energy and reducing the laser scanning rate results in deeper melt pool formation. Moreover, PLSM has led to entirely dissolution of the carbides and re-solidification of cellular/dendritic structure of a fine scale surrounded by a continuous interdendritic network. This caused an increase in surface microhardness, 2-4 times over that of the base metal.

Investigation on the surface characterization of Ga-faced GaN after chemical-mechanical polishing

Energy Technology Data Exchange (ETDEWEB)

Gong, Hua [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Shenzhen Key Laboratory of Micro/nano Manufacturing, Research Institute of Tsinghua University in Shenzhen, Shenzhen 518057 (China); Pan, Guoshun, E-mail: pangs@tsinghua.edu.cn [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Shenzhen Key Laboratory of Micro/nano Manufacturing, Research Institute of Tsinghua University in Shenzhen, Shenzhen 518057 (China); Zhou, Yan; Shi, Xiaolei; Zou, Chunli; Zhang, Suman [State Key Laboratory of Tribology, Tsinghua University, Beijing 100084 (China); Shenzhen Key Laboratory of Micro/nano Manufacturing, Research Institute of Tsinghua University in Shenzhen, Shenzhen 518057 (China)

2015-05-30

Highlights: • Tiny-sized nanoparticles were introduced in GaN CMP to realize a good surface. • The relationship between surface characterization and abrasive size was conducted. • An atomic step-terrace structure was achieved on GaN surface after CMP. • Pt/C catalyst nanoparticles were used in GaN CMP to get a higher MRR. - Abstract: The relationship between the surface characterization after chemical mechanical polishing (CMP) and the size of the silica (SiO{sub 2}) abrasive used for CMP of gallium nitride (GaN) substrates was investigated in detail. Atomic force microscope was used for measuring the surface morphology, pit feature, pit depth distribution, and atomic step-terrace structure. With the decrease of SiO{sub 2} abrasive size, the pit depth reduced and the atomic step-terrace structure became more whole with smaller damage area, resulting in smaller roughness. For tiny-sized SiO{sub 2} abrasive, an almost complete atomic step-terrace structure with 0.0523 nm roughness was achieved. On the other hand, in order to acquire higher removal, Pt/C nanoparticle was employed as a catalyst in CMP slurry. The result indicates that when Pt/C catalyst content was reached to 1.0 ppm, material removal rate was increased by 47.69% compared to that by none of the catalyst, and besides, the pit depth reduced and the surface atomic step-terrace structure was not destroyed. The Pt/C nanoparticle is proved to be the promising catalyst to the surface preparation of super-hard and inert materials with high efficiency and good surface.

Growth mechanism of graphene on platinum: Surface catalysis and carbon segregation

International Nuclear Information System (INIS)

Sun, Jie; Lindvall, Niclas; Yurgens, August; Nam, Youngwoo; Cole, Matthew T.; Teo, Kenneth B. K.; Woo Park, Yung

2014-01-01

A model of the graphene growth mechanism of chemical vapor deposition on platinum is proposed and verified by experiments. Surface catalysis and carbon segregation occur, respectively, at high and low temperatures in the process, representing the so-called balance and segregation regimes. Catalysis leads to self-limiting formation of large area monolayer graphene, whereas segregation results in multilayers, which evidently “grow from below.” By controlling kinetic factors, dominantly monolayer graphene whose high quality has been confirmed by quantum Hall measurement can be deposited on platinum with hydrogen-rich environment, quench cooling, tiny but continuous methane flow and about 1000 °C growth temperature

Growth of graphene from SiC{0001} surfaces and its mechanisms

International Nuclear Information System (INIS)

Norimatsu, Wataru; Kusunoki, Michiko

2014-01-01

Graphene, a one-atom-layer carbon material, can be grown by thermal decomposition of SiC. On Si-terminated SiC(0001), graphene nucleates at steps and grows layer-by-layer, and as a result a homogeneous monolayer or bilayer can be obtained. We demonstrate this mechanism both experimentally and theoretically. On the C-face (000 1-bar ), multilayer graphene nucleates not only at steps, but also on the terraces. These differences reflect the distinct differences in the reactivity of these faces. Due to its high quality and structural controllability, graphene on SiC{0001} surfaces will be a platform for high-speed graphene device applications. (paper)

Nonlinear mechanics of surface growth for cylindrical and spherical elastic bodies

Science.gov (United States)

Sozio, Fabio; Yavari, Arash

2017-01-01

In this paper we formulate the initial-boundary value problems of accreting cylindrical and spherical nonlinear elastic solids in a geometric framework. It is assumed that the body grows as a result of addition of new (stress-free or pre-stressed) material on part of its boundary. We construct Riemannian material manifolds for a growing body with metrics explicitly depending on the history of applied external loads and deformation during accretion and the growth velocity. We numerically solve the governing equilibrium equations in the case of neo-Hookean solids and compare the accretion and residual stresses with those calculated using the linear mechanics of surface growth.

The Role of Subjective Task Value in Service-Learning Engagement among Chinese College Students.

Science.gov (United States)

Li, Yulan; Guo, Fangfang; Yao, Meilin; Wang, Cong; Yan, Wenfan

2016-01-01

Most service-learning studies in higher education focused on its effects on students' development. The dynamic processes and mechanisms of students' development during service-learning, however, have not been explored thoroughly. Student engagement in service-learning may affect service-learning outcomes and be affected by subjective task value at the same time. The present study aimed to explore the effect of subjective task value on Chinese college student engagement during service-learning. Fifty-four Chinese college students participated in a 9-weeks service-learning program of interacting with children with special needs. Students' engagement and subjective task value were assessed via self-report questionnaires and 433 weekly reflective journals. The results indicated that the cognitive, emotional and behavioral engagement of Chinese college students demonstrated different developmental trends during service-learning process. Subjective task value played an essential role in student engagement in service-learning activities. However, the role of subjective task value varied with different stages. Finally, the implications for implementing service-learning in Chinese education were discussed.

The Role of Subjective Task Value in Service-Learning Engagement among Chinese College Students

Science.gov (United States)

Li, Yulan; Guo, Fangfang; Yao, Meilin; Wang, Cong; Yan, Wenfan

2016-01-01

Most service-learning studies in higher education focused on its effects on students’ development. The dynamic processes and mechanisms of students’ development during service-learning, however, have not been explored thoroughly. Student engagement in service-learning may affect service-learning outcomes and be affected by subjective task value at the same time. The present study aimed to explore the effect of subjective task value on Chinese college student engagement during service-learning. Fifty-four Chinese college students participated in a 9-weeks service-learning program of interacting with children with special needs. Students’ engagement and subjective task value were assessed via self-report questionnaires and 433 weekly reflective journals. The results indicated that the cognitive, emotional and behavioral engagement of Chinese college students demonstrated different developmental trends during service-learning process. Subjective task value played an essential role in student engagement in service-learning activities. However, the role of subjective task value varied with different stages. Finally, the implications for implementing service-learning in Chinese education were discussed. PMID:27445919

Formation Mechanism of Surface Crack in Low Pressure Casting of A360 Alloy

Science.gov (United States)

Liu, Shan-Guang; Cao, Fu-Yang; Ying, Tao; Zhao, Xin-Yi; Liu, Jing-Shun; Shen, Hong-Xian; Guo, Shu; Sun, Jian-Fei

2017-12-01

A surface crack defect is normally found in low pressure castings of Al alloy with a sudden contraction structure. To further understand the formation mechanism of the defect, the mold filling process is simulated by a two-phase flow model. The experimental results indicate that the main reason for the defect deformation is the mismatching between the height of liquid surface in the mold and pressure in the crucible. In the case of filling, a sudden contraction structure with an area ratio smaller than 0.5 is obtained, and the velocity of the liquid front increases dramatically with the influence of inertia. Meanwhile, the pressurizing speed in the crucible remains unchanged, resulting in the pressure not being able to support the height of the liquid level. Then the liquid metal flows back to the crucible and forms a relatively thin layer solidification shell on the mold wall. With the increasing pressure in the crucible, the liquid level rises again, engulfing the shell and leading to a surface crack. As the filling velocity is characterized by the damping oscillations, surface cracks will form at different heights. The results shed light on designing a suitable pressurizing speed for the low pressure casting process.

Engagement of nurses in their profession. Qualitative study on engagement.

Science.gov (United States)

García-Sierra, Rosa; Fernández-Castro, Jordi; Martínez-Zaragoza, Fermín

To identify common issues of nurses with high engagement to enable us to develop the construct as it applies to nursing in more depth. Based on the constructivist paradigm and with a phenomenological approach, a qualitative content analysis was conducted using an inductive approach. Participants were nurses working in direct care in different healthcare areas. The sample size was determined by data saturation and 15 participants were interviewed. The units of meaning were grouped into 11 subcategories, and then into 7 categories termed vigour, dedication, reward, autonomy, social support, conciliation and attributes of nurses. Then these categories were grouped into 3 major themes: job characteristics, characteristics of organizations, and individual characteristics. Having high engagement does not mean ignoring the negative aspects of work and organizations. Nurses who maintain high engagement are also affected by the negative aspects, however the assessment of positive aspects such as enjoying the work, the meaning of being a nurse, reward and autonomy enable the process of depletion of engagement to be overcome. In view of the findings, we propose reconceptualising the construct, taking the features of nursing into account. Copyright © 2017 Elsevier España, S.L.U. All rights reserved.

The Need for Systematic Identification of Stakeholders for Public Engagement with Environmental Research

Science.gov (United States)

Despite the increasing promotion of stakeholder engagement in science contributing to environmental decision making, the mechanisms for identifying which stakeholders should be included are rarely strategic or documented. When documented, many of these efforts use ad hoc and/or ...

Mechanical, Thermal Degradation, and Flammability Studies on Surface Modified Sisal Fiber Reinforced Recycled Polypropylene Composites

Directory of Open Access Journals (Sweden)

Arun Kumar Gupta

2012-01-01

Full Text Available The effect of surface treated sisal fiber on the mechanical, thermal, flammability, and morphological properties of sisal fiber (SF reinforced recycled polypropylene (RPP composites was investigated. The surface of sisal fiber was modified with different chemical reagent such as silane, glycidyl methacrylate (GMA, and O-hydroxybenzene diazonium chloride (OBDC to improve the compatibility with the matrix polymer. The experimental results revealed an improvement in the tensile strength to 11%, 20%, and 31.36% and impact strength to 78.72%, 77%, and 81% for silane, GMA, and OBDC treated sisal fiber reinforced recycled Polypropylene (RPP/SF composites, respectively, as compared to RPP. The thermogravimetric analysis (TGA, differential scanning calorimeter (DSC, and heat deflection temperature (HDT results revealed improved thermal stability as compared with RPP. The flammability behaviour of silane, GMA, and OBDC treated SF/RPP composites was studied by the horizontal burning rate by UL-94. The morphological analysis through scanning electron micrograph (SEM supports improves surface interaction between fiber surface and polymer matrix.

Radiation-curing of acrylate composites including carbon fibres: A customized surface modification for improving mechanical performances

International Nuclear Information System (INIS)

Martin, Arnaud; Pietras-Ozga, Dorota; Ponsaud, Philippe; Kowandy, Christelle; Barczak, Mariusz; Defoort, Brigitte; Coqueret, Xavier

2014-01-01

The lower transverse mechanical properties of radiation-cured acrylate-based composites reinforced with carbon-fibre with respect to the thermosettable analogues was investigated from the viewpoint of chemical interactions at the interface between the matrix and the carbon material. XPS analysis of representative commercial carbon fibres revealed the presence of a significant amount of chemical functions potentially exerting an adverse effect on the initiation and propagation of the free radical polymerization initiated under high energy radiation. The EB-induced polymerization of n-butyl acrylate as a simple model monomer was conducted in the presence of various aromatic additives exhibiting a strong inhibiting effect, whereas thiols efficiently sensitize the initiation mechanism and undergo transfer reactions. A method based on the surface modification of sized fibres by thiomalic acid is proposed for overcoming the localized inhibition phenomenon and for improving the mechanical properties of the resulting acrylate-based composites. - Highlights: • Surface functions of C-fibres are analyzed for their effect on radical reaction. • Irradiation of nBu-acrylate in presence of aromatic additives reveals inhibition. • Thiol groups sensitize the radiation-initiated polymerization of nBu-acrylate. • Modification of C-fibres with thiomalic acid enhances composite properties

Operations of human resources engagement

OpenAIRE

Δημητρέλη, Αλεξάνδρα

2017-01-01

This current study, attempts to shed light on the relationship between HR Operations and employee engagement by testing the relationship empirically. More specifically, it looks at how employee engagement could be embedded into day-to-day human resources operations. Employee engagement is a topic that is repeatedly being discussed in most of the HR forums, articles and journals in the recent past. Employers recognize that truly engage and motivate employee’s produce impressive levels of in...

The effect of metal ion implantation on the surface mechanical properties of Mylar (PET)

Energy Technology Data Exchange (ETDEWEB)

Zhou, W.; Sood, D.K. [Royal Melbourne Inst. of Tech., VIC (Australia); Yao, X.; Brown, I.G. [California Univ., Berkeley, CA (United States). Lawrence Berkeley Lab.

1993-12-31

Ion implantation of polymers leads to the formation of new carbonaceous materials, the revolution during implantation of various species consists of (1) ion beam induced damage: chain scission, crosslinking, molecular emission of volatile elements and compounds, stoichiometric change in the surface layer of pristine polymers; and (2) chemical effect between ion and target materials: microalloying and precipitation. Literature regarding ion implanted polymers shows that the reorganisation of the carbon network after implantation can dramatically modify several properties of pristine polymers solubility, molecular weight, and electrical, optical and mechanical properties. However, ion implantation of polymers is actually a very complex interaction which depends on not only ion species, implantation condition, but also polymer type and specific structure. In this paper the effect of Ag or Ti ions implantation on surface mechanical properties of PET (polyethylenne terephthalate) polymer is reported. There was a clear deterioration in wear resistance after implantation of both Ag and Ti ions. It is suggested that the increment of wear after implantation may result from not only ion damage but also chemical effect between ion and target material. 3 refs., 1 tab., 2 figs.

The effect of metal ion implantation on the surface mechanical properties of Mylar (PET)

Energy Technology Data Exchange (ETDEWEB)

Zhou, W; Sood, D K [Royal Melbourne Inst. of Tech., VIC (Australia); Yao, X; Brown, I G [California Univ., Berkeley, CA (United States). Lawrence Berkeley Lab.

1994-12-31

Ion implantation of polymers leads to the formation of new carbonaceous materials, the revolution during implantation of various species consists of (1) ion beam induced damage: chain scission, crosslinking, molecular emission of volatile elements and compounds, stoichiometric change in the surface layer of pristine polymers; and (2) chemical effect between ion and target materials: microalloying and precipitation. Literature regarding ion implanted polymers shows that the reorganisation of the carbon network after implantation can dramatically modify several properties of pristine polymers solubility, molecular weight, and electrical, optical and mechanical properties. However, ion implantation of polymers is actually a very complex interaction which depends on not only ion species, implantation condition, but also polymer type and specific structure. In this paper the effect of Ag or Ti ions implantation on surface mechanical properties of PET (polyethylenne terephthalate) polymer is reported. There was a clear deterioration in wear resistance after implantation of both Ag and Ti ions. It is suggested that the increment of wear after implantation may result from not only ion damage but also chemical effect between ion and target material. 3 refs., 1 tab., 2 figs.

Teacher Narratives and Student Engagement: Testing Narrative Engagement Theory in Drug Prevention Education

Science.gov (United States)

Miller-Day, Michelle; Hecht, Michael L.; Krieger, Janice L.; Pettigrew, Jonathan; Shin, YoungJu; Graham, John

2015-01-01

Testing narrative engagement theory, this study examines student engagement and teachers’ spontaneous narratives told in a narrative-based drug prevention curriculum. The study describes the extent to which teachers share their own narratives in a narrative-based curriculum, identifies dominant narrative elements, forms and functions, and assesses the relationships among teacher narratives, overall lesson narrative quality, and student engagement. One hundred videotaped lessons of the keepin’ it REAL drug prevention curriculum were coded and the results supported the claim that increased narrative quality of a prevention lesson would be associated with increased student engagement. The quality of narrativity, however, varied widely. Implications of these results for narrative-based prevention interventions and narrative pedagogy are discussed. PMID:26690668

Wetting-layer formation mechanisms of surface-directed phase separation under different quench depths with off-critical compositions in polymer binary mixture

Science.gov (United States)

Yan, Li-Tang; Xie, Xu-Ming

2007-02-01

Focusing on the off-critical condition, the quench depth dependence of surface-directed phase separation in the polymer binary mixture is numerically investigated by combination of the Cahn-Hilliard-Cook theory and the Flory-Huggins-de Gennes theory. Two distinct situations, i.e., for the wetting, the minority component is preferred by the surface and the majority component is preferred by the surface, are discussed in detail. The simulated results show that the formation mechanism of the wetting layer is affected by both the quench depth and the off-critical extent. Moreover, a diagram, illustrating the formation mechanisms of the wetting layer with various quench depths and compositions, is obtained on the basis of the simulated results. It is found that, when the minority component is preferred by the surface, the growth of the wetting layer can exhibit pure diffusion limited growth law, logarithmic growth law, and Lifshitz-Slyozov growth law. However, when the majority component is preferred by the surface, the wetting layer always grows logarithmically, regardless of the quench depth and the off-critical extent. It is interesting that the surface-induced nucleation can be observed in this case. The simulated results demonstrate that the surface-induced nucleation only occurs below a certain value of the quench depth, and a detailed range about it is calculated and indicated. Furthermore, the formation mechanisms of the wetting layer are theoretically analyzed in depth by the chemical potential gradient.

Three-Dimensional Finite Element Analysis on Stress Distribution of Internal Implant-Abutment Engagement Features.

Science.gov (United States)

Cho, Sung-Yong; Huh, Yun-Hyuk; Park, Chan-Jin; Cho, Lee-Ra

To investigate the stress distribution in an implant-abutment complex with a preloaded abutment screw by comparing implant-abutment engagement features using three-dimensional finite element analysis (FEA). For FEA modeling, two implants-one with a single (S) engagement system and the other with a double (D) engagement system-were placed in the human mandibular molar region. Two types of abutments (hexagonal, conical) were connected to the implants. Different implant models (a single implant, two parallel implants, and mesial and tilted distal implants with 1-mm bone loss) were assumed. A static axial force and a 45-degree oblique force of 200 N were applied as the sum of vectors to the top of the prosthetic occlusal surface with a preload of 30 Ncm in the abutment screw. The von Mises stresses at the implant-abutment and abutment-screw interfaces were measured. In the single implant model, the S-conical abutment type exhibited broader stress distribution than the S-hexagonal abutment. In the double engagement system, the stress concentration was high in the lower contact area of the implant-abutment engagement. In the tilted implant model, the stress concentration point was different from that in the parallel implant model because of the difference in the bone level. The double engagement system demonstrated a high stress concentration at the lower contact area of the implant-abutment interface. To decrease the stress concentration, the type of engagement features of the implant-abutment connection should be carefully considered.

Engaging Stakeholders in Curriculum Development

Science.gov (United States)

Wood, Jo Nell

2010-01-01

This article investigates the importance of parent and community engagement in curriculum development, along with curriculum leadership, engaging stakeholders, and the importance of curriculum. Parent and community member engagement is examined in light of curriculum committee participation as reported by Missouri superintendents. Survey responses…

Strategic Engagement in Global S&T: Opportunities for Defense Research

Science.gov (United States)

2014-01-01

ameliorating global chal- lenges, such as natural and engineered disasters (e.g., Fukushima Daiichi nuclear disaster ) and pandemic disease outbreaks (e.g...importance of both maintaining awareness of global S&T advances and increasing engagement with other parts of the U.S. government, industry, academia...perspectives on the following themes: mission, mechanisms for technology awareness , relationship building, enterprise coordination and connectivity, and

Conceptualizing Culturally Infused Engagement and Its Measurement for Ethnic Minority and Immigrant Children and Families

Science.gov (United States)

Pottick, Kathleen J.; Chen, Yun

2017-01-01

Despite the central role culture plays in racial and ethnic disparities in mental health among ethnic minority and immigrant children and families, existing measures of engagement in mental health services have failed to integrate culturally specific factors that shape these families' engagement with mental health services. To illustrate this gap, the authors systematically review 119 existing instruments that measure the multi-dimensional and developmental process of engagement for ethnic minority and immigrant children and families. The review is anchored in a new integrated conceptualization of engagement, the culturally infused engagement model. The review assesses culturally relevant cognitive, attitudinal, and behavioral mechanisms of engagement from the stages of problem recognition and help seeking to treatment participation that can help illuminate the gaps. Existing measures examined four central domains pertinent to the process of engagement for ethnic minority and immigrant children and families: (a) expressions of mental distress and illness, (b) causal explanations of mental distress and illness, (c) beliefs about mental distress and illness, and (d) beliefs and experiences of seeking help. The findings highlight the variety of tools that are used to measure behavioral and attitudinal dimensions of engagement, showing the limitations of their application for ethnic minority and immigrant children and families. The review proposes directions for promising research methodologies to help intervention scientists and clinicians improve engagement and service delivery and reduce disparities among ethnic minority and immigrant children and families at large, and recommends practical applications for training, program planning, and policymaking. PMID:28275923

The thumb carpometacarpal joint: curvature morphology of the articulating surfaces, mathematical description and mechanical functioning.

Science.gov (United States)

Dathe, Henning; Dumont, Clemens; Perplies, Rainer; Fanghänel, Jochen; Kubein-Meesenburg, Dietmar; Nägerl, Hans; Wachowski, Martin M

2016-01-01

The purpose is to present a mathematical model of the function of the thumb carpometacarpal joint (TCMCJ) based on measurements of human joints. In the TCMCJ both articulating surfaces are saddle-shaped. The aim was to geometrically survey the shapes of the articulating surfaces using precise replicas of 28 TCMCJs. None of these 56 articulating surfaces did mathematically extend the differential geometrical neighbourhood around the main saddle point so that each surface could be characterised by three main parameters: the two extreme radii of curvature in the main saddle point and the angle between the saddles' asymptotics (straight lines). The articulating surfaces, when contacting at the respective main saddle points, are incongruent. Hence, the TCMCJ has functionally five kinematical degrees of freedom (DOF); two DOF belong to flexion/extension, two to ab-/adduction. These four DOF are controlled by the muscular apparatus. The fifth DOF, axial rotation, cannot be adjusted but stabilized by the muscular apparatus so that physiologically under compressive load axial rotation does not exceed an angle of approximately ±3°. The TCMCJ can be stimulated by the muscular apparatus to circumduct. The mechanisms are traced back to the curvature incongruity of the saddle surfaces. Hence we mathematically proved that none of the individual saddle surfaces can be described by a quadratic saddle surface as is often assumed in literature. We derived an algebraic formula with which the articulating surfaces in the TCMCJ can be quantitatively described. This formula can be used to shape the articulating surfaces in physiologically equivalent TCMCJ-prostheses.

Engaging men in health care.

Science.gov (United States)

Malcher, Greg

2009-03-01

Engaging men in health care involves a multifaceted approach that has as its main principle the recognition that men consume health care differently to women. This article identifies barriers to engaging men in health care and offers potential and existing solutions to overcome these barriers in a range of health care settings. The concept of multiple masculinities recognises that not all men can be engaged via a particular technique or strategy. The perception that men are disinterested in their health is challenged and a range of approaches discussed, both in the community and in health care facilities. In the general practice setting opportunities exist for the engagement of men at the reception desk and waiting room, as well as during the consultation. Use of the workplace in engaging men is discussed. Future activities to build the capacity of health care providers to better engage men are identified and the role of policy and program development is addressed.

Work Engagement, Intrinsic Motivation and Job Satisfaction among Employees of A Coal Mining Company in South Borneo

Directory of Open Access Journals (Sweden)

Hasan Sartono

2016-07-01

Full Text Available This paper seeks to establish the relationships between three job characteristics constructs, namely work engagement, intrinsic motivation and job satisfaction in a workplace notorious for discord and conflict between workers and employers. A quantitative methodology was adopted using a cross-sectional survey. Respondents were selected from the workers at a mining company, with a final sample of 156 employees participating in the study. The Utrecht Work Engagement Scale, Intrinsic Motivation Inventory and the Minnesota JobSatisfaction Questionnaire were used to collect data. The results of the study indicate positive relationships between job satisfaction, work engagement and intrinsic motivation among the workers. Age and marital status were found to be significant contributors to workers’ job satisfaction, intrinsic motivation and work engagement. Implications of these results are that human resource interventions are required in order to deal with enhancing work engagement, intrinsic motivation and job satisfaction. Furthermore, the results indicate that intrinsic motivation and work engagement can enhance job satisfaction. The current study adds to the research pointing at job satisfaction as a promising underlying mechanism for employees’ to be internally motivated and engaged at work. Keywords: Work engagement, Intrinsic motivation, Job satisfaction

Dynamic Equilibrium Mechanism for Surface Nanobubble Stabilization

NARCIS (Netherlands)

Brenner, Michael P.; Lohse, Detlef

2008-01-01

Recent experiments have convincingly demonstrated the existence of surface nanobubbles on submerged hydrophobic surfaces. However, classical theory dictates that small gaseous bubbles quickly dissolve because their large Laplace pressure causes a diffusive outflux of gas. Here we suggest that the

Engaging the aging workforce: the relationship between perceived age similarity, satisfaction with coworkers, and employee engagement.

Science.gov (United States)

Avery, Derek R; McKay, Patrick F; Wilson, David C

2007-11-01

Business publications and the popular press have stressed the importance of creating conditions for meaningful employee expression in work roles, also known as engagement. Few empirical studies, however, have examined how individual or situational factors relate to engagement. Consequently, this study examines the interplay between employee age, perceived coworker age composition, and satisfaction with older (older than 55) and younger (younger than 40) coworkers on engagement using a sample of 901 individuals employed in the United Kingdom. Results indicated that satisfaction with one's coworkers related significantly to engagement. Moreover, perceived age similarity was associated with higher levels of engagement among older workers when they were highly satisfied with their coworkers over 55 and lower levels of engagement when they were not. (c) 2007 APA

Engaging Conversationally: A Method for Engaging Students in Their Learning and Examining Instruction

Directory of Open Access Journals (Sweden)

Michael Kiener

2008-08-01

Full Text Available Under the principles of the scholarship of teaching and learning and action research this study sought to examine how an instructor created and facilitated engagement in his students. The research was primarily undertaken to further define the middle range theory of mutual engagement. Theoretical sampling was used to analyze approximately 100 pieces of data that included instructor notes, teaching observations, feedback from conference presentations, student assessments, and end of semester student evaluations. Engaging conversationally (EC emerged as the phenomenon that described the instructor’s engagement in the learning process. EC was an ongoing cyclical pattern of inquiry that included preparing, reflecting and modeling. Interconnected in the pattern of inquiry were personality traits, counselor education, and teaching philosophy.

Analytical modelling for ultrasonic surface mechanical attrition treatment

Directory of Open Access Journals (Sweden)

Guan-Rong Huang

2015-07-01

Full Text Available The grain refinement, gradient structure, fatigue limit, hardness, and tensile strength of metallic materials can be effectively enhanced by ultrasonic surface mechanical attrition treatment (SMAT, however, never before has SMAT been treated with rigorous analytical modelling such as the connection among the input energy and power and resultant temperature of metallic materials subjected to SMAT. Therefore, a systematic SMAT model is actually needed. In this article, we have calculated the averaged speed, duration time of a cycle, kinetic energy and kinetic energy loss of flying balls in SMAT for structural metallic materials. The connection among the quantities such as the frequency and amplitude of attrition ultrasonic vibration motor, the diameter, mass and density of balls, the sample mass, and the height of chamber have been considered and modelled in details. And we have introduced the one-dimensional heat equation with heat source within uniform-distributed depth in estimating the temperature distribution and heat energy of sample. In this approach, there exists a condition for the frequency of flying balls reaching a steady speed. With these known quantities, we can estimate the strain rate, hardness, and grain size of sample.

A Novel Approach for Enhancement of Automobile Clutch Engagement Quality Using Mechatronics Based Automated Clutch System

Science.gov (United States)

Tripathi, K.

2013-01-01

In automated manual clutch (AMC) a mechatronic system controls clutch force trajectory through an actuator governed by a control system. The present study identifies relevant characteristics of this trajectory and their effects on driveline dynamics and engagement quality. A new type of force trajectory is identified which gives the good engagement quality. However this trajectory is not achievable through conventional clutch control mechanism. But in AMC a mechatronic system based on electro-hydraulic or electro-mechanical elements can make it feasible. A mechatronic system is presented in which a mechatronic add-on system can be used to implement the novel force trajectory, without the requirement of replacing the traditional diaphragm spring based clutch in a vehicle with manual transmission.

A Review of Effective Youth Engagement Strategies for Mental Health and Substance Use Interventions.

Science.gov (United States)

Dunne, Tom; Bishop, Lisa; Avery, Susan; Darcy, Stephen

2017-05-01

The majority of adult mental health and substance use (MH&SU) conditions emerge in adolescence. Prevention, diagnosis, and treatment programs targeting this age group have a unique opportunity to significantly impact the well-being of the future generation of adults. At the same time, youth are reluctant to seek treatment and have high rates of dropout from interventions. An emphasis on youth engagement in prevention and treatment interventions for MH&SU results in better health outcomes for those youth. This literature review was undertaken to evaluate opportunities to improve youth engagement in MH&SU programs. The intent was to determine best practices in the field that combined community-level improvement in clinical outcomes with proven strategies in engagement enhancement to inform program development at a local level. The results discuss 40 studies, reviews, and program reports demonstrating effective youth engagement. These have been grouped into six themes based on the underlying engagement mechanism: youth participation in program development, parental relationships, technology, the health clinic, school, and social marketing. A broad range of tools are discussed that intervention developers can leverage to improve youth engagement in prevention or treatment programs. Copyright © 2016 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

RELATIONSHIPS AMONG COMPONENTS OF ENGAGEMENT RISK

Directory of Open Access Journals (Sweden)

EVREN DILEK SENGUR

2012-01-01

Full Text Available Accounting scandals exploded at the beginning of 2000s and the collapse of Arthur Andersen highlighted the importance of implementing engagement risk management strategies in audit firms. Engagement risk refers the overall risk associated with an audit engagement and it consists of three components: client's business risk, auditor's business risk, and audit risk. The main purpose of this study is to describe each components of engagement risk and explain relations among them. Additionally, the paper points out the importance of engagement risk management throughout the audit and demonstrates engagement risk management strategies at client acceptance/ continuance, planning and completion of audit.

Student Engagement: Body, Mind and Heart – A Proposal for an Embedded Multi-Dimensional Student Engagement Framework

OpenAIRE

Pickford, R

2016-01-01

This paper considers student engagement in the context of a diverse higher education population and explores what institutions can do to impact positively on student engagement. The paper takes as its starting point the goals of higher education and the purposes of student engagement and reflects on the politicisation of student engagement, and the relative positioning of the student and the higher education institution in relation to student engagement. The paper suggests conditions for and ...

Students' Engagement with Learning Technologies

Science.gov (United States)

Larkin, Derek; Huett, Kim C.

2013-01-01

This paper seeks to add to the discussion surrounding young adults' relationship and engagement with learning technologies, exploring whether they naturally engage with these technologies when the use of them is either compulsory or optional. We discuss our findings in relation to whether young people are truly engaging with technologies or…

An adhesive contact mechanics formulation based on atomistically induced surface traction

Energy Technology Data Exchange (ETDEWEB)

Fan, Houfu [Department of Civil and Environmental Engineering, University of California, Berkeley, CA 94720 (United States); Ren, Bo [Livermore Software Technology Corporation, 7374 Las Positas Road, Livermore, CA 94551 (United States); Li, Shaofan, E-mail: shaofan@berkeley.edu [Department of Civil and Environmental Engineering, University of California, Berkeley, CA 94720 (United States)

2015-12-01

In this work, we have developed a novel multiscale computational contact formulation based on the generalized Derjuguin approximation for continua that are characterized by atomistically enriched constitutive relations in order to study macroscopic interaction between arbitrarily shaped deformable continua. The proposed adhesive contact formulation makes use of the microscopic interaction forces between individual particles in the interacting bodies. In particular, the double-layer volume integral describing the contact interaction (energy, force vector, matrix) is converted into a double-layer surface integral through a mathematically consistent approach that employs the divergence theorem and a special partitioning technique. The proposed contact model is formulated in the nonlinear continuum mechanics framework and implemented using the standard finite element method. With no large penalty constant, the stiffness matrix of the system will in general be well-conditioned, which is of great significance for quasi-static analysis. Three numerical examples are presented to illustrate the capability of the proposed method. Results indicate that with the same mesh configuration, the finite element computation based on the surface integral approach is faster and more accurate than the volume integral based approach. In addition, the proposed approach is energy preserving even in a very long dynamic simulation.

Decomposition mechanism of formic acid on Cu (111) surface: A theoretical study

Energy Technology Data Exchange (ETDEWEB)

Jiang, Zhao, E-mail: jiangzhao@mail.xjtu.edu.cn; Qin, Pei; Fang, Tao

2017-02-28

Highlights: • Adsorption and decomposition mechanism of HCOOH on Cu (111) were investigated using DFT calculations. • The stable co-adsorption configurations of related intermediates were identified. • Five dissociation pathways of HCOOH via initial H−O, C−H and C−O bond scissions were considered and analyzed. - Abstract: The study of formic acid decomposition on transition metal surfaces is important to obtain useful information for vapor phase catalysis involving HCOOH and for the development of direct formic acid fuel cells. In this study, periodic density functional theory calculations have been employed to investigate the dissociation pathways of HCOOH on Cu (111) surface. About adsorption, it is found that the adsorption of HCOO, COOH, HCO, CO, OH and H on Cu (111) are considered chemisorption, whereas HCOOH, CO{sub 2}, H{sub 2}O and H{sub 2} have the weak interaction with Cu (111) surface. Furthermore, the minimum energy pathways are analyzed for the decomposition of HCOOH to CO{sub 2} and CO through the scission of H−O, C−H and C−O bonds. It is found that HCOOH, HCOO and COOH prefer to dissociate in the related reactions rather than desorb. For the decomposition, it is indicated that HCO and COOH are the main dissociated intermediates of trans-HCOOH, CO{sub 2} is the main dissociated intermediates of bidentate-HCOO, and CO is the main dissociated product of cis-COOH. The co-adsorbed H atom is beneficial for the formation of CO{sub 2} from cis-COOH. Besides, it is found that the most favorable path for HCOOH decomposition on Cu (111) surface is HCOOH-HCO-CO (Path 5), where the step of CO formation from HCO dehydrogenation is considered to be the rate-determining step. The results also show that CO is preferentially formed as the dominant product of HCOOH on Cu (111) surface.

An Analysis of Historical Global Warming and Social Engagement

OpenAIRE

Train, Joseph; Roizenman, David; Damiani, Seth; Rochwerg, Ronny

2018-01-01

The goal of this paper is to determine whether there is a correlation between awareness of global warming, and where global warming occurs. This theory is carried out by analyzing maps containing various forms of data that have to do with global warming, such as precipitation and surface temperature, and comparing it with a map of engagement from tweets which mention global warming. This paper found that there is no solid correlation between mentioning global warming in tweets and global warm...

Surface decoration of polyimide fiber with carbon nanotubes and its application for mechanical enhancement of phosphoric acid-based geopolymers

Science.gov (United States)

Yang, Tao; Han, Enlin; Wang, Xiaodong; Wu, Dezhen

2017-09-01

A new methodology to decorate the surface of polyimide (PI) fiber with carbon nanotubes (CNTs) has been developed in this study. This surface decoration was carried out through a surface alkali treatment, a carboxylation modification, surface functionalization with acyl chloride groups and then with amino groups, and a surface graft of CNTs onto PI fiber. Fourier-transform infrared and X-ray photoelectron spectroscopic characterizations confirmed that CNTs were chemically grafted onto the surface of PI fiber, and scanning electron microscopic observation demonstrated the fiber surface was uniformly and densely covered with CNTs. The surface energy and wettability of PI fiber were improved in the presence of CNTs on the fiber surface, which made a contribution to enhance the interfacial adhesion of PI fiber with other inorganic matrices when used as a reinforcing fiber. The application of CNTs-decorated PI fiber for the reinforcement of phosphoric acid-based geopolymers was investigated, and the results indicated that the geopolymeric composites gained a noticeable reinforcement. Compared to unreinforced geopolymer, the geopolymeric composites achieved a remarkable increase in compressive strength by 120% and in flexural strength by 283%. Fractography investigation demonstrated that the interaction adhesion between the fibers and matrix was enhanced due to the surface decoration of PI fiber with CNTs, which contributed to an improvement in fracture-energy dissipation by fiber pullout and fiber debonding from the matrix. As a result, a significant reinforcement effect on geopolymeric composites was achieved through a fiber-bridging mechanism. This study provided an effective methodology to improve the interracial bonding force for PI fiber and also proves a highly efficient application of CNTs-decorated PI fiber for the mechanical enhancement of geopolymeric composites.

Spent-fuel special-studies progress report: probable mechanisms for oxidation and dissolution of single-crystal UO2 surfaces

International Nuclear Information System (INIS)

Wang, R.

1981-03-01

Due to the complexity of the structural, microstructural and compositional characteristics of spent fuel, basic leaching and dissolution mechanisms were studied with UO 2 matrix material, specifically with single-crystal UO 2 , to isolate individual contributory factors. The effects of oxidation and oxidation-dissolution were investigated in different oxidation conditions, such as in air, oxygenated solutions and deionized water containing H 2 O 2 . In addition, the effects of temperature on dissolution of UO 2 were studied in autoclaves at 75 and 150 0 C. Also, oxidation and dissolution measurements were investigated via electrochemical methods to determine if those techniques could be applied to the characterization of leaching and dissolution of spent fuel in a hot cell. Finally, the effects of radiation were explored since the radiolysis of water may create a localized oxidizing condition at or near the spent fuel-solution interface, even in neutral or reducing conditions as commonly found in deep geological environments. The oxidation and oxidation-dissolution mechanisms for UO 2 are proposed as follows: The UO 2 surface is first oxidized in solution to form a UO/sub 2+x/ surface layer several angstroms thick. This oxidized surface has a high dissolution rate since the UO/sub 2+x/ reacts with the dissolved O 2 , or H 2 O 2 , to form uranyl complex ions in a U(VI) state. As the uranyl ions exceed the solubility limits in solution, they become hydrolyzed to form solid deposits and suspended particles of UO 3 hydrates. The thickness and porosity of the deposited UO 3 hydrate surface-film is dependent on temperature, pH and deposition time. A long-term dissolution rate is then determined by the nature of the surface film, such as porosity, solubility and mechanical properties

Stakeholder Engagement in HIV Cure Research: Lessons Learned from Other HIV Interventions and the Way Forward.

Science.gov (United States)

Lo, Ying-Ru; Chu, Carissa; Ananworanich, Jintanat; Excler, Jean-Louis; Tucker, Joseph D

2015-07-01

Clinical and basic science advances have raised considerable hope for achieving an HIV cure by accelerating research. This research is dominated primarily by issues about the nature and design of current and future clinical trials. Stakeholder engagement for HIV cure remains in its early stages. Our analysis examines timing and mechanisms of historical stakeholder engagement in other HIV research areas for HIV-uninfected individuals [vaccine development and pre-exposure prophylaxis (PrEP)], and HIV-infected individuals (treatment as prevention, prevention of mother-to-child transmission, and treatment of acute HIV infection) and articulate a plan for HIV cure stakeholder engagement. The experience from HIV vaccine development shows that early engagement of stakeholders helped manage expectations, mitigating the failure of several vaccine trials, while paving the way for subsequent trials. The relatively late engagement of HIV stakeholders in PrEP research may partly explain some of the implementation challenges. The treatment-related stakeholder engagement was strong and community-led from the onset and helped translation from research to implementation. We outline five steps to initiate and sustain stakeholder engagement in HIV cure research and conclude that stakeholder engagement represents a key investment in which stakeholders mutually agree to share knowledge, benefits, and risk of failure. Effective stakeholder engagement prevents misconceptions. As HIV cure research advances from early trials involving subjects with generally favorable prognosis to studies involving greater risk and uncertainty, success may depend on early and deliberate engagement of stakeholders.

Employee Engagement: A Literature Review

Directory of Open Access Journals (Sweden)

Dharmendra MEHTA

2013-12-01

Full Text Available Motivated and engaged employees tend to contribute more in terms of organizational productivity and support in maintaining a higher commitment level leading to the higher customer satisfaction. Employees Engagement permeates across the employee-customer boundary, where revenue, corporate goodwill, brand image are also at stake. This paper makes an attempt to study the different dimensions of employee engagement with the help of review of literature. This can be used to provide an overview and references on some of the conceptual and practical work undertaken in the area of the employee engagement practices.

Approaching Engagement towards Human-Engaged Computing

DEFF Research Database (Denmark)

Niksirat, Kavous Salehzadeh; Sarcar, Sayan; Sun, Huatong

2018-01-01

Debates regarding the nature and role of HCI research and practice have intensified in recent years, given the ever increasingly intertwined relations between humans and technologies. The framework of Human-Engaged Computing (HEC) was proposed and developed over a series of scholarly workshops to...

What Is Student Engagement?

Science.gov (United States)

Groccia, James E.

2018-01-01

This chapter reviews the history and various definitions of student engagement and proposes a multidimensional model from which one can develop a variety of engagement opportunities that lead to a rich and challenging higher education experience.

Public engagement on global health challenges.

Science.gov (United States)

Cohen, Emma R M; Masum, Hassan; Berndtson, Kathryn; Saunders, Vicki; Hadfield, Tom; Panjwani, Dilzayn; Persad, Deepa L; Minhas, Gunjeet S; Daar, Abdallah S; Singh, Jerome A; Singer, Peter A

2008-05-20

Experience with public engagement activities regarding the risks and benefits of science and technology (S&T) is growing, especially in the industrialized world. However, public engagement in the developing world regarding S&T risks and benefits to explore health issues has not been widely explored. This paper gives an overview about public engagement and related concepts, with a particular focus on challenges and benefits in the developing world. We then describe an Internet-based platform, which seeks to both inform and engage youth and the broader public on global water issues and their health impacts. Finally, we outline a possible course for future action to scale up this and similar online public engagement platforms. The benefits of public engagement include creating an informed citizenry, generating new ideas from the public, increasing the chances of research being adopted, increasing public trust, and answering ethical research questions. Public engagement also fosters global communication, enables shared experiences and methodology, standardizes strategy, and generates global viewpoints. This is especially pertinent to the developing world, as it encourages previously marginalized populations to participate on a global stage. One of the core issues at stake in public engagement is global governance of science and technology. Also, beyond benefiting society at large, public engagement in science offers benefits to the scientific enterprise itself. Successful public engagement with developing world stakeholders will be a critical part of implementing new services and technologies. Interactive engagement platforms, such as the Internet, have the potential to unite people globally around relevant health issues.

Public engagement on global health challenges

Directory of Open Access Journals (Sweden)

Minhas Gunjeet S

2008-05-01

Full Text Available Abstract Background Experience with public engagement activities regarding the risks and benefits of science and technology (S&T is growing, especially in the industrialized world. However, public engagement in the developing world regarding S&T risks and benefits to explore health issues has not been widely explored. Methods This paper gives an overview about public engagement and related concepts, with a particular focus on challenges and benefits in the developing world. We then describe an Internet-based platform, which seeks to both inform and engage youth and the broader public on global water issues and their health impacts. Finally, we outline a possible course for future action to scale up this and similar online public engagement platforms. Results The benefits of public engagement include creating an informed citizenry, generating new ideas from the public, increasing the chances of research being adopted, increasing public trust, and answering ethical research questions. Public engagement also fosters global communication, enables shared experiences and methodology, standardizes strategy, and generates global viewpoints. This is especially pertinent to the developing world, as it encourages previously marginalized populations to participate on a global stage. One of the core issues at stake in public engagement is global governance of science and technology. Also, beyond benefiting society at large, public engagement in science offers benefits to the scientific enterprise itself. Conclusion Successful public engagement with developing world stakeholders will be a critical part of implementing new services and technologies. Interactive engagement platforms, such as the Internet, have the potential to unite people globally around relevant health issues.