Retail yield and fabrication times for veal as influenced by purchasing options and merchandising styles.

Science.gov (United States)

McNeill, M S; Griffin, D B; Dockerty, T R; Walter, J P; Johnson, H K; Savell, J W

1998-06-01

Twenty-nine selected styles of subprimals or sections of veal were obtained from a commercial facility to assist in the development of a support program for retailers. They were fabricated into bone-in or boneless retail cuts and associated components by trained meat cutters. Each style selected (n = 6) was used to generate mean retail yields and labor requirements, which were calculated from wholesale and retail weights and processing times. Means and standard errors for veal ribs consisting of five different styles (n = 30) concluded that style #2, 7-rib 4 (10 cm) x 4 (10 cm), had the lowest percentage of total retail yield (P < .05) owing to the greatest percentage of bone. Furthermore, rib style #2 required the longest total processing time (P < .05). Rib styles #3, 7-rib chop-ready, and #5, 6-rib chop ready, yielded the greatest percentage of total retail yield and also had the shortest total processing time (P < .05). Within veal loins, style #2, 4 (10 cm) x 4 (10 cm) loin kidney fat in, had the greatest percentage fat (P < .05). Loin styles #2 and #3, 4 (10 cm) x 4 (10 cm) loin special trimmed, generated more lean and fat trimmings and bone, resulting in lower percentage of total retail yields than loin style #1, 0 (0 cm) x 1 (2.5 cm) loin special trimmed (P < .05). Results indicated that bone-in subprimals and sections required more processing time if fabricated into a boneless end point. In addition, as the number of different retail cuts increased, processing times also increased.

HUD Subprime and Manufactured Home Lender List

Data.gov (United States)

Department of Housing and Urban Development — The U.S. Department of Housing and Urban Development (HUD) periodically produce its HUD Subprime and Manufactured home Lender List for the lenders who specialize in...

A Study on Mechanical behavior of Tensile Specimen Fabricated by Laser Cutting

Energy Technology Data Exchange (ETDEWEB)

Jin, Y. G.; Kim, G. S.; Baik, S. J.; Baek, S. Y. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The mechanical testing data are required for the assessment of dry storage of the spent nuclear fuel. Laser cutting system could be useful tools for material processing such as cutting in radioactive environment due to non-contact nature, ease in handling and the laser cutting process is most advantageous, offering the narrow kerf width and heat affected zone by using small beam spot diameter. The feasibility of the laser cutting system was demonstrated for the fabrication of various types of the unirradiated cladding with and without oxide layer on the specimens. In the present study, the dimensional measurement and tensile test were conducted to investigate the mechanical behavior of the axial tensile test specimens depending on the material processing methods in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. Laser cutting system was used to fabricate the tensile test specimens, and the mechanical behavior was investigated using the dimensional measurement and tensile test. It was shown that the laser beam machining could be a useful tool to fabricate the specimens and this technique will be developed for the fabrication of various types of irradiated specimens in a hotcell.

A Study on Mechanical behavior of Tensile Specimen Fabricated by Laser Cutting

International Nuclear Information System (INIS)

Jin, Y. G.; Kim, G. S.; Baik, S. J.; Baek, S. Y.

2016-01-01

The mechanical testing data are required for the assessment of dry storage of the spent nuclear fuel. Laser cutting system could be useful tools for material processing such as cutting in radioactive environment due to non-contact nature, ease in handling and the laser cutting process is most advantageous, offering the narrow kerf width and heat affected zone by using small beam spot diameter. The feasibility of the laser cutting system was demonstrated for the fabrication of various types of the unirradiated cladding with and without oxide layer on the specimens. In the present study, the dimensional measurement and tensile test were conducted to investigate the mechanical behavior of the axial tensile test specimens depending on the material processing methods in a hot cell at IMEF (Irradiated Materials Examination Facility) of KAERI. Laser cutting system was used to fabricate the tensile test specimens, and the mechanical behavior was investigated using the dimensional measurement and tensile test. It was shown that the laser beam machining could be a useful tool to fabricate the specimens and this technique will be developed for the fabrication of various types of irradiated specimens in a hotcell

The Impact of Feeding Diets of High or Low Energy Concentration on Carcass Measurements and the Weight of Primal and Subprimal Lean Cuts

Directory of Open Access Journals (Sweden)

A. P. Schinckel

2012-04-01

Full Text Available Pigs from four sire lines were allocated to a series of low energy (LE, 3.15 to 3.21 Mcal ME/kg corn-soybean meal-based diets with 16% wheat midds or high energy diets (HE, 3.41 to 3.45 Mcal ME/kg with 4.5 to 4.95% choice white grease. All diets contained 6% DDGS. The HE and LE diets of each of the four phases were formulated to have equal lysine:Mcal ME ratios. Barrows (N = 2,178 and gilts (N = 2,274 were fed either high energy (HE or low energy (LE diets from 27 kg BW to target BWs of 118, 127, 131.5 and 140.6 kg. Carcass primal and subprimal cut weights were collected. The cut weights and carcass measurements were fitted to allometric functions (Y = A CWB of carcass weight. The significance of diet, sex or sire line with A and B was evaluated by linearizing the equations by log to log transformation. The effect of diet on A and B did not interact with sex or sire line. Thus, the final model was B where Diet = −0.5 for the LE and 0.5 for HE diets and A and B are sire line-sex specific parameters. cut weight = (1+bD(Diet A(CW Diet had no affect on loin, Boston butt, picnic, baby back rib, or sparerib weights (p>0.10, bD = −0.003, −0.0029, 0.0002, 0.0047, −0.0025, respectively. Diet affected ham weight (bD = −0.0046, p = 0.01, belly weight (bD = 0.0188, p = 0.001 three-muscle ham weight (bD = −0.014, p = 0.001, boneless loin weight (bD = −0.010, p = 0.001, tenderloin weight (bD = −0.023, p = 0.001, sirloin weight (bD = −0.009, p = 0.034, and fat-free lean mass (bD = −0.0145, p = 0.001. Overall, feeding the LE diets had little impact on primal cut weight except to decrease belly weight. Feeding LE diets increased the weight of lean trimmed cuts by 1 to 2 percent at the same carcass weight.

Investigation of Micro Square Structure Fabrication by Applying Textured Cutting Tool in WEDM

Directory of Open Access Journals (Sweden)

Jianguo Zhang

2015-09-01

Full Text Available This paper studies micro structure fabrication by means of a textured tool cutting edge, which is manufactured by applying the wire cut electrical discharge machining (WEDM. Machining performance of the square structure fabrication on the tool cutting edge is investigated in the WEDM process, and the machining accuracy is explored in experimental analyses. In this proposed method, undesired overcut comes from the discharge between the processing debris and the side wall of the target structure. Furthermore, by applying the textured cutting tool, the target square structure is directly fabricated on the alumina workpiece with just a simple turning process, which verifies the feasibility of the proposed tool cutting edge textured method by applying the WEDM. This technology is expected to become a potential method for the mass production of micro structure surfaces in the future.

From Tulip Bulbs to Sub-Prime Mortgages Examining the Sub-Prime Crisis: The Case for a Systemic Approach

Science.gov (United States)

Stephens, Alan A.; Atwater, J. Brian; Kannan, Vijay R.

2013-01-01

Purpose: The collapse of the sub-prime mortgage market parallels several earlier failures within the financial services sector, begging the question why the lessons of past failures were not learned. Throughout history from the tulip bulb crisis of the 1600s to the most recent economic crisis, decision-makers keep making the same mistakes. This…

The supreme subprime myth: the role of bad loans in the 2007-2009 financial crisis

Directory of Open Access Journals (Sweden)

Alberto Niccoli

2012-03-01

Full Text Available Using simulations, we show that the probability of default and losses given default of subprime mortgage loans are small in comparison to their interest rates. The implication is that these loans are profitable for risk neutral efficient banks. As subprime mortgages remain a good investment even for higher values of probability of default and losses given default, our conclusion is that they did not trigger the 2007-2009 financial crisis. In contrast with other papers, this finding does not derive from analyses relating to the subprime market size, but from the positive ex-ante net present value of their discounted cash flows.

Ameliorating Local Impacts with Architectural Research: Subprime Mortgages & Housing Quality

Directory of Open Access Journals (Sweden)

Lynne M. Dearborn

2012-10-01

Full Text Available Shock waves from the current housing crisis that still echo through Wall Street’s largest financial firms, not only have threatened to topple financial markets and drive the country into a depression, but have also undermined the all-time high home ownership rate in the United States. The most attention-grabbing dimensions and headlines of the current crisis seem to be the staggering losses incurred by the likes of Bear Sterns and Citigroup, and the demise of some of the large corporations such as Washington Mutual. However, the real crisis is not on Wall Street or in the banking sector, but in low- and moderate-income and minority homes and neighborhoods throughout the country. At least ten years before the present subprime foreclosure crisis became mainstream news, these marginalized communities were feeling the negative effects of mortgage fraud and predatory lending practices occurring with regularity in the subprime market. This paper discusses an ongoing study of Subprime Lending, Mortgage Fraud and Housing Quality in process since 2002. This four-part study has employed foreclosure data with statistical and mapping analysis, detailed interviews with victims of predatory lending, systematic documentation of the resulting housing environments, and documentation of property improvements in light of victims’ legal settlements. While subprime lending has supported the expansion of homeownership in the United States, this on-going study suggests that this expansion has sometimes been at the expense of safe, code-compliant living environments forlow-income, minority and elderly homeowners. Some of the victims of predatory lending and mortgage fraud have sought legal redress through the courts but many have suffered personal financial, health, emotional, and family crises as well. The current broad-scale discussion of the topic has given attention to the lack of regulation facilitating these unethical practices, but it is unclear that current

Design and Fabrication of Automatic Glass Cutting Machine

Science.gov (United States)

Veena, T. R.; Kadadevaramath, R. S.; Nagaraj, P. M.; Madhusudhan, S. V.

2016-09-01

This paper deals with the design and fabrication of the automatic glass or mirror cutting machine. In order to increase the accuracy of cut and production rate; and decrease the production time and accidents caused due to manual cutting of mirror or glass, this project aims at development of an automatic machine which uses a programmable logic controller (PLC) for controlling the movement of the conveyer and also to control the pneumatic circuit. In this machine, the work of the operator is to load and unload the mirror. The cutter used in this machine is carbide wheel with its cutting edge ground to a V-shaped profile. The PLC controls the pneumatic cylinder and intern actuates the cutter along the glass, a fracture layer is formed causing a mark to be formed below the fracture layer and a crack to be formed below the rib mark. The machine elements are designed using CATIA V5R20 and pneumatic circuit are designed using FESTO FLUID SIM software.

Development and validation of equations utilizing lamb vision system output to predict lamb carcass fabrication yields.

Science.gov (United States)

Cunha, B C N; Belk, K E; Scanga, J A; LeValley, S B; Tatum, J D; Smith, G C

2004-07-01

This study was performed to validate previous equations and to develop and evaluate new regression equations for predicting lamb carcass fabrication yields using outputs from a lamb vision system-hot carcass component (LVS-HCC) and the lamb vision system-chilled carcass LM imaging component (LVS-CCC). Lamb carcasses (n = 149) were selected after slaughter, imaged hot using the LVS-HCC, and chilled for 24 to 48 h at -3 to 1 degrees C. Chilled carcasses yield grades (YG) were assigned on-line by USDA graders and by expert USDA grading supervisors with unlimited time and access to the carcasses. Before fabrication, carcasses were ribbed between the 12th and 13th ribs and imaged using the LVS-CCC. Carcasses were fabricated into bone-in subprimal/primal cuts. Yields calculated included 1) saleable meat yield (SMY); 2) subprimal yield (SPY); and 3) fat yield (FY). On-line (whole-number) USDA YG accounted for 59, 58, and 64%; expert (whole-number) USDA YG explained 59, 59, and 65%; and expert (nearest-tenth) USDA YG accounted for 60, 60, and 67% of the observed variation in SMY, SPY, and FY, respectively. The best prediction equation developed in this trial using LVS-HCC output and hot carcass weight as independent variables explained 68, 62, and 74% of the variation in SMY, SPY, and FY, respectively. Addition of output from LVS-CCC improved predictive accuracy of the equations; the combined output equations explained 72 and 66% of the variability in SMY and SPY, respectively. Accuracy and repeatability of measurement of LM area made with the LVS-CCC also was assessed, and results suggested that use of LVS-CCC provided reasonably accurate (R2 = 0.59) and highly repeatable (repeatability = 0.98) measurements of LM area. Compared with USDA YG, use of the dual-component lamb vision system to predict cut yields of lamb carcasses improved accuracy and precision, suggesting that this system could have an application as an objective means for pricing carcasses in a value

Design and fabrication of an AT-cut quartz phononic Lamb wave resonator

International Nuclear Information System (INIS)

Hung, Chia-Hao; Liu, Ting-Wei; Wu, Tsung-Tsong; Wang, Wei-Shan; Esashi, Masayoshi; Lin, Yu-Ching; Sun, Jia-Hong; Chen, Yung-Yu

2013-01-01

This paper presents results on the design and fabrication of an AT-cut quartz Lamb wave resonator with phononic crystal (PC) reflective gratings. The deep reactive ion etching process with a laboratory-made etcher was utilized to fabricate PC structures of the AT-cut quartz Lamb wave resonator. The finite element method was adopted to calculate the PC band structure, effective reflective distance from the PC boundary and further the resonant modes and admittance of the phononic Lamb wave resonant cavity. Through the comparison studies between the experimental and simulated results, a design process for the AT-cut quartz phononic Lamb wave resonator was proposed. It is noted that by using the phononic reflectors, the size of the Lamb wave resonator can be reduced significantly. (paper)

Online evaluation of a commercial video image analysis system (Computer Vision System) to predict beef carcass red meat yield and for augmenting the assignment of USDA yield grades. United States Department of Agriculture.

Science.gov (United States)

Cannell, R C; Belk, K E; Tatum, J D; Wise, J W; Chapman, P L; Scanga, J A; Smith, G C

2002-05-01

Objective quantification of differences in wholesale cut yields of beef carcasses at plant chain speeds is important for the application of value-based marketing. This study was conducted to evaluate the ability of a commercial video image analysis system, the Computer Vision System (CVS) to 1) predict commercially fabricated beef subprimal yield and 2) augment USDA yield grading, in order to improve accuracy of grade assessment. The CVS was evaluated as a fully installed production system, operating on a full-time basis at chain speeds. Steer and heifer carcasses (n = 296) were evaluated using CVS, as well as by USDA expert and online graders, before the fabrication of carcasses into industry-standard subprimal cuts. Expert yield grade (YG), online YG, CVS estimated carcass yield, and CVS measured ribeye area in conjunction with expert grader estimates of the remaining YG factors (adjusted fat thickness, percentage of kidney-pelvic-heart fat, hot carcass weight) accounted for 67, 39, 64, and 65% of the observed variation in fabricated yields of closely trimmed subprimals. The dual component CVS predicted wholesale cut yields more accurately than current online yield grading, and, in an augmentation system, CVS ribeye measurement replaced estimated ribeye area in determination of USDA yield grade, and the accuracy of cutability prediction was improved, under packing plant conditions and speeds, to a level close to that of expert graders applying grades at a comfortable rate of speed offline.

The effect of the subprime crisis on the credit risk in global scale

Science.gov (United States)

Lee, Sangwook; Kim, Min Jae; Lee, Sun Young; Kim, Soo Yong; Ban, Joon Hwa

2013-05-01

Credit default swap (CDS) has become one of the most actively traded credit derivatives, and its importance in finance markets has increased after the subprime crisis. In this study, we analyzed the correlation structure of credit risks embedded in CDS and the influence of the subprime crisis on this topological space. We found that the correlation was stronger in the cluster constructed according to the location of the CDS reference companies than in the one constructed according to their industries. The correlation both within a given cluster and between different clusters became significantly stronger after the subprime crisis. The causality test shows that the lead lag effect between the portfolios (into which reference companies are grouped by the continent where each of them is located) is reversed in direction because the portion of non-investable and investable reference companies in each portfolio has changed since then. The effect of a single impulse has increased and the response time relaxation has become prolonged after the crisis as well.

SPILLOVER EFFECTS OF THE SUB-PRIME MORTGAGE CRISIS TO THE ASIAN STOCK MARKETS

Directory of Open Access Journals (Sweden)

Esta Lestari

2014-10-01

Full Text Available AbstractThis paper aims to analyze the effects of the sub-prime mortgage crisis on several Asian stock markets. An Exponential Generalized Autoregressive Conditional Heteroscedasticity (EGARCH model is employed to provide an empirical evidence of the direct spillover. The indirect effect is measured through the spillover effects from the increased volatility in the U.S. stock markets to the Asian stock markets. The results showed that the market integration occurs within Asian stock markets. Meanwhile the asymmetric effects are evident for all the Asian countries stock markets, indicating that financial markets in Asia are suffered more from negative news (shocks lead to more volatilities compared to positive news. Keywords: Stock market, sub-prime mortgage crisis, volatility, spillover effectJEL classification numbers: C22, F36, G15AbstrakPaper ini bertujuan untuk menganalisis pengaruh krisis sub-prime mortgage pada beberapa pasar saham Asia. Model Exponential Generalized Autoregressive Conditional Heteroscedasticity (EGARCH digunakan untuk mendapatkan bukti empiris dari kenaikan volatilitas dalam pasar saham Amerika pada pasar-pasar saham Asia. Hasil analisis memperlihatkan bahwa integrasi pasar terjadi di dalam pasar saham Asia. Sementara itu, pengaruh asimetris terbukti terjadi di pasar-pasar saham Asia, mengindikasikan bahwa pasar-pasar keuangan di Asia menderita lebih parah sebagai akibat dari kejutan negatif dibandingkan dengan dampak dari kejutan positif.Kata kunci: Pasar saham, krisis sub-prime mortgage, volatilitas, pengaruh spillover JEL classification numbers: C22, F36, G15

Impacto da Crise do Subprime na Provisão do Risco de Crédito dos Maiores Bancos NacionaisImpact of the Subprime Crisis in the Provision of Credit Risk of Major National BanksImpacto de la Crisis del Subprime en la Provisión para el Riesgo de Crédito de los Mayores Bancos Nacionales

Directory of Open Access Journals (Sweden)

TOLEDO FILHO, Jorge Ribeiro de

2009-09-01

Full Text Available RESUMOAs instituições financeiras estão diretamente expostas ao risco de crédito, que é o risco de o tomador não cumprir com suas obrigações, ou seja, com o pagamento das dívidas nos seus prazos estabelecidos. Para tanto, os bancos fazem as provisões para este tipo de risco, que constam de seus balanços. Em 2006/2007 houve o impacto de uma nova crise financeira que se espalhou pelo mundo, conhecida como a crise do subprime. O objetivo deste estudo é analisar se as provisões para risco de crédito aumentaram após o início da crise do subprime nos dez maiores bancos nacionais, selecionados de acordo com os seus ativos totais. Para responder a essa questão, foram analisados os balanços patrimoniais de cada um desses bancos no período de 2005 a 2007. Esta pesquisa se caracteriza, quanto aos objetivos, como descritiva e, quanto aos procedimentos, como documental. Quanto à abordagem, caracteriza-se como qualitativa. Os resultados apontam que a crise do subprime gerou pouco impacto na provisão dos riscos de crédito das instituições analisadas. Identificou-se um ligeiro aumento nos índices de provisão no auge da crise em 2006. Em 2007 esses percentuais diminuíram, provavelmente devido à estabilidade econômica do país e da estagnação da crise do subprime naquele ano, pelo menos em seu reflexo no Brasil.ABSTRACTFinancial institutions are directly exposed to the credit risk, that is, the risk of the borrower not fulfill with their obligations, paying their debts in its stated periods established previously. The banks predict this type of risk, including them in their balance-sheets. In 2006/2007 there was the impact of a new financial crisis that spread around the world, known as the crisis of subprime. The objective of this study is to analyze if the provisions for credit risk or liquidation increased the sprouting of the crisis of subprime in ten major national banks, chosen accordant to their total assets. To answer this

Com a cabeça nas nuvens da crise dos Subprimes | Head in the clouds of the sub-prime crisis

Directory of Open Access Journals (Sweden)

Yann Moulier Boutang

2009-09-01

Full Text Available Resumo o texto apresenta a crise dos subprimes como a manifestação da impossibilidade de separação entre especulação e mercado da economia-mundo. A crise atual é apontada como sendo a primeira crise global do comunismo do capital e uma interdependência entre devedores e credores. A menos que se invente um novo New Deal, que refunde os antigos direitos do Estado-providência e crie novos direitos de novos trabalhadores, não se vê meio pelo qual um programa de eutanásia da renda evitará a explosão política. Palavras-chave crise; capitalismo cognitivo; renda; economia mundial. Abstract the paper presents the subprime crisis as a manifestation of the impossibility of separating speculation and market from the world economy. The current crisis is pointed out as being the first global crisis of communism of capital and also an interdependence between debtors and creditors. Unless a new New Deal is invented, which recasts the ancient rights of the welfare state and creates new rights for new workers, there is no means by which a program of euthanasia may avoid political explosion. Keywords crisis; cognitive capitalism; rent; world economy.

Influence of Lay Plan Solution in Fabric Efficiency and Consume in Cutting Section

OpenAIRE

Dumishllari Elmira; Guxho Genti

2016-01-01

One cutting order may require several lies and markers to achieve optimal efficiency and selection of right Lay Plan is one of the major challenges in cutting section, in a way to lead in fabric economy and reduced costs. The main purpose of this paper is to determine the best solution of lay plan and its influence, in the cutting room, starting from the analysis of the lay indicators calculations. We have studied an order with 200 jackets, with specific sizes. Markers are made by Gemini CAD ...

Use of an Electrostatic Spraying System or the Sprayed Lethality in Container Method To Deliver Antimicrobial Agents onto the Surface of Beef Subprimals To Control Shiga Toxin-Producing Escherichia coli.

Science.gov (United States)

Stella, J Max; Luchansky, John B; Miller, Kelsey; Shoyer, Bradley A; Shane, Laura E; McGeary, Lianna; Osoria, Manuela; Stahler, Laura J; Sevart, Nicholas J; Phebus, Randall K; Thippareddi, Harshavardhan; Porto-Fett, Anna C S

2017-08-01

The efficacy of an electrostatic spraying system (ESS) and/or the sprayed lethality in container (SLIC) method to deliver antimicrobial agents onto the surface of beef subprimals to reduce levels of Shiga toxin-producing Escherichia coli (STEC) was evaluated. Beef subprimals were surface inoculated (lean side; ca. 5.8 log CFU per subprimal) with 2 mL of an eight-strain cocktail comprising single strains of rifampin-resistant (100 μg/mL) STEC (O26:H11, O45:H2, O103:H2, O104:H4, O111:H - , O121:H19, O145:NM, and O157:H7). Next, inoculated subprimals were surface treated with lauric arginate (LAE; 1%), peroxyacetic acid (PAA; 0.025%), or cetylpyridinium chloride (CPC; 0.4%) by passing each subprimal, with the inoculated lean side facing upward, through an ESS cabinet or via SLIC. Subprimals were then vacuum packaged and stored at 4°C. One set of subprimals was sampled after an additional 2 h, 3 days, or 7 days of refrigerated storage, whereas another set was retreated via SLIC after 3 days of storage with a different one of the three antimicrobial agents (e.g., a subprimal treated with LAE on day 0 was then treated with PAA or CPE on day 3). Retreated subprimals were sampled after 2 h or 4 days of additional storage at 4°C. A single initial application of LAE, PAA, or CPC via ESS or SLIC resulted in STEC reductions of ca. 0.3 to 1.3 log CFU per subprimal after 7 days of storage. However, when subprimals were initially treated with LAE, PAA, or CPC via ESS or SLIC and then separately retreated with a different one of these antimicrobial agents via SLIC on day 3, additional STEC reductions of 0.4 to 1.0 log CFU per subprimal were observed after an additional 4 days of storage. Application of LAE, PAA, or CPC, either alone or in combination, via ESS or SLIC is effective for reducing low levels (ca. 0.3 to 1.6 log CFU) of STEC that may be naturally present on the surface of beef subprimals.

Contagion of us subprime mortgage crisis to Colombian economy: measured by financial market data

Directory of Open Access Journals (Sweden)

Chu V. Nguyen

2011-06-01

Full Text Available The long-horizon event study methodology is used to document the severe impact of the US subprime mortgage crisis on the Colombian economy. The estimated parameter of a constantmean return model is used to derive the “abnormal return” on the market portfolios of Colombia over its selected event window. Analyses of the results reveal that the US subprime mortgage crisis negatively affected both the Colombian and the US equity markets almost identically in terms of cumulative percentage reductions and timing. Statistic testing results seem to support the qualitative observation. This phenomenon can be attributable to the recent multilateral and regional trade agreements that increase the flow of trade and foreign direct investment to Colombia.

Credit Booms and Lending Standards : Evidence from the Subprime Mortgage Market

NARCIS (Netherlands)

Dell’Ariccia, G.; Igan, D.; Laeven, L.

2009-01-01

This paper links the current subprime mortgage crisis to a decline in lending standards associated with the rapid expansion and changes in the structure of this market. We show that lending standards declined more in areas that experienced faster credit growth. We also find that the entry of new

Credit booms and lending standards : Evidence from the subprime mortgage market

NARCIS (Netherlands)

Dell’Ariccia, G.; Igan, D.; Laeven, L.

2012-01-01

This paper links the U.S. subprime mortgage crisis to demand-side factors that contributed to the rapid expansion of the U.S. mortgage market. We show that denial rates were relatively lower in areas that experienced faster credit demand growth and that lenders in these high-growth areas attached

Corporate Bond Liquidity Before and After the Onset of the Subprime Crisis

DEFF Research Database (Denmark)

Dick-Nielsen, Jens; Feldhütter, Peter; Lando, David

2012-01-01

We analyze liquidity components of corporate bond spreads during 2005–2009 using a new robust illiquidity measure. The spread contribution from illiquidity increases dramatically with the onset of the subprime crisis. The increase is slow and persistent for investment grade bonds while the effect...

Revisiting Stock Market Integration Pre-Post Subprime Mortgage Crisis: Insight From BRIC Countries

Directory of Open Access Journals (Sweden)

Chin-Hong Puah

2015-07-01

Full Text Available This study revisits the long-run relationships and short-run dynamic causal linkages among BRIC stock market, with the particular attention to the 2008 subprime mortgage crisis. Extending related empirical studies, comparative analyses of pre-crisis, and post-crisis periods were conducted to comprehensively evaluate how stock market integration was affected by financial crises. In general, after employing cointegration test and VAR test, the results reveal the increase of stock market integration in BRICs after the subprime crisis. The evidence also found that China stock market is the most influential among the BRICs, in which China stock market has the ability to Granger cause the other three BRICs member countries. An important implication of our findings is that the degree of integration among countries tends to change over time, especially around periods marked by financial crises.

Why the Community Reinvestment Act cannot be blamed for the subprime crisis

NARCIS (Netherlands)

Aalbers, M.B.

2009-01-01

It has become common practice—and in particular, but not exclusively, in conservative media—to blame the Community Reinvestment Act (CRA) of 1977 for the U.S. subprime mortgage and foreclosure crisis that triggered the global financial crisis. It is argued that the CRA forced lenders to give

Fabricating 40 µm-thin silicon solar cells with different orientations by using SLiM-cut method

Science.gov (United States)

Wang, Teng-Yu; Chen, Chien-Hsun; Shiao, Jui-Chung; Chen, Sung-Yu; Du, Chen-Hsun

2017-10-01

Thin silicon foils with different crystal orientations were fabricated using the stress induced lift-off (SLiM-cut) method. The thickness of the silicon foils was approximately 40 µm. The ≤ft foil had a smoother surface than the ≤ft foil. With surface passivation, the minority carrier lifetimes of the ≤ft and ≤ft silicon foil were 1.0 µs and 1.6 µs, respectively. In this study, 4 cm2-thin silicon solar cells with heterojunction structures were fabricated. The energy conversion efficiencies were determined to be 10.74% and 14.74% for the ≤ft and ≤ft solar cells, respectively. The surface quality of the silicon foils was determined to affect the solar cell character. This study demonstrated that fabricating the solar cell by using silicon foil obtained from the SLiM-cut method is feasible.

Analysis of the temperature of the hot tool in the cut of woven fabric using infrared images

Science.gov (United States)

Borelli, Joao E.; Verderio, Leonardo A.; Gonzaga, Adilson; Ruffino, Rosalvo T.

2001-03-01

Textile manufacture occupies a prominence place in the national economy. By virtue of its importance researches have been made on the development of new materials, equipment and methods used in the production process. The cutting of textiles starts in the basic stage, to be followed within the process of the making of clothes and other articles. In the hot cutting of fabric, one of the variables of great importance in the control of the process is the contact temperature between the tool and the fabric. The work presents a technique for the measurement of the temperature based on the processing of infrared images. For this a system was developed composed of an infrared camera, a framegrabber PC board and software that analyzes the punctual temperature in the cut area enabling the operator to achieve the necessary control of the other variables involved in the process.

Laser Cutting of Carbon Fiber Fabrics

Science.gov (United States)

Fuchs, A. N.; Schoeberl, M.; Tremmer, J.; Zaeh, M. F.

Due to their high weight-specific mechanical stiffness and strength, parts made from carbon fiber reinforced polymers (CFRP) are increasingly used as structural components in the aircraft and automotive industry. However, the cutting of preforms, as with most automated manufacturing processes for CFRP components, has not yet been fully optimized. This paper discusses laser cutting, an alternative method to the mechanical cutting of preforms. Experiments with remote laser cutting and gas assisted laser cutting were carried out in order to identify achievable machining speeds. The advantages of the two different processes as well as their fitness for use in mass production are discussed.

FINANCIAL DERIVATIVES - MEANINGS BEYOND SUBPRIME CRISIS STIGMA

Directory of Open Access Journals (Sweden)

FELICIA RAMONA BIRĂU

2012-12-01

Full Text Available Derivatives are designed as complex financial instruments and their main aim is to manage the risk associated with the underlying asset, in order to ensure against fluctuations in value, or to profit from periods of inactivity, instability or decline. In recent years financial derivatives have experienced a fulminant development and also they have been perceived as an effective lever of the modern economy. The subprime crisis was triggered by a quite significant financial infrastructure glitch, which coalesced around certain factors influence, such as : highly permissive regulation of financial markets, speculative bubbles, underperforming risk management, liquidity injections and structural imbalances. Despite the fact that is a innovative segment and quite difficult affordable as understanding level of the operation mechanisms, financial derivatives were only the tool triggering this global dimension crisis.

Herding Behavior and Rating Convergence among Credit Rating Agencies : Evidence from the Subprime Crisis

NARCIS (Netherlands)

Lugo, Stefano; Croce, Annalisa; Faff, Robert

2015-01-01

This article examines how credit rating agencies (CRAs) react to rating decisions on mortgage-backed securities by rival agencies in the aftermath of the subprime crisis. While Fitch is on average the first mover, Moody’s and S&P perform more timely downgrades given a downgrade or a more severe

Evaluation of Capacitive Markers Fabricated by 3D Printing, Laser Cutting and Prototyping

Directory of Open Access Journals (Sweden)

Julian Kreimeier

2018-01-01

Full Text Available With Tangible User Interfaces, the computer user is able to interact in a fundamentally different and more intuitive way than with usual 2D displays. By grasping real physical objects, information can also be conveyed haptically, i.e., the user not only sees information on a 2D display, but can also grasp physical representations. To recognize such objects (“tangibles” it is skillful to use capacitive sensing, as it happens in most touch screens. Thus, real objects can be located and identified by the touch screen display automatically. Recent work already addressed such capacitive markers, but focused on their coding scheme and automated fabrication by 3D printing. This paper goes beyond the fabrication by 3D printers and, for the first time, applies the concept of capacitive codes to laser cutting and another immediate prototyping approach using modeling clay. Beside the evaluation of additional properties, we adapt recent research results regarding the optimized detection of tangible objects on capacitive screens. As a result of our comprehensive study, the detection performance is affected by the type of capacitive signal processing (respectively the device and the geometry of the marker. 3D printing revealed to be the most reliable technique, though laser cutting and immediate prototyping of markers showed promising results. Based on our findings, we discuss individual strengths of each capacitive marker type.

Local Authority Residential Mortgage Credit: A Source of Non-Market Sub-Prime Homeloans for Low-Income households

Directory of Open Access Journals (Sweden)

Dermot Coates

2008-01-01

Full Text Available As the volume of mortgage credit has risen in tandem with house price inflation, the sub-prime homeloan sector of this market has begun to expand in order to meet demand from those not serviced by the mainstream financial service providers. This article examines the role of local authorities in providing residential mortgages and assesses whether those who have traditionally borrowed from non-market (or public sector lenders would be considered to be sub-prime borrowers by the private sector. It concludes that, in view of the relatively low average incomes of this cohort of borrowers, they represent a higher probability of homeloan default and as a consequence, would be subject to a higher cost of credit in the private sector. However, this paper highlights the favourable terms offered by local authorities and argues that their failure to price according to the risk profile of borrowers exposes the Exchequer to higher – and often unquantified – costs in pursuit of promoting home-ownership.

Dimensional accuracy of internal cooling channel made by selective laser melting (SLM And direct metal laser sintering (DMLS processes in fabrication of internally cooled cutting tools

Directory of Open Access Journals (Sweden)

Ghani S. A. C.

2017-01-01

Full Text Available Selective laser melting(SLM and direct metal laser sintering(DMLS are preferred additive manufacturing processes in producing complex physical products directly from CAD computer data, nowadays. The advancement of additive manufacturing promotes the design of internally cooled cutting tool for effectively used in removing generated heat in metal machining. Despite the utilisation of SLM and DMLS in a fabrication of internally cooled cutting tool, the level of accuracy of the parts produced remains uncertain. This paper aims at comparing the dimensional accuracy of SLM and DMLS in machining internally cooled cutting tool with a special focus on geometrical dimensions such as hole diameter. The surface roughness produced by the two processes are measured with contact perthometer. To achieve the objectives, geometrical dimensions of identical tool holders for internally cooled cutting tools fabricated by SLM and DMLS have been determined by using digital vernier calliper and various magnification of a portable microscope. In the current study, comparing internally cooled cutting tools made of SLM and DMLS showed that generally the higher degree of accuracy could be obtained with DMLS process. However, the observed differences in surface roughness between SLM and DMLS in this study were not significant. The most obvious finding to emerge from this study is that the additive manufacturing processes selected for fabricating the tool holders for internally cooled cutting tool in this research are capable of producing the desired internal channel shape of internally cooled cutting tool.

Designing for hot-blade cutting

DEFF Research Database (Denmark)

Brander, David; Bærentzen, Jakob Andreas; Clausen, Kenn

2016-01-01

In this paper we present a novel method for the generation of doubly-curved, architectural design surfaces using swept Euler elastica and cubic splines. The method enables a direct design to production workflow with robotic hot-blade cutting, a novel robotic fabrication method under development......-trivial constraints of blade-cutting in a bottom-up fashion, enabling an exploration of the unique architectural potential of this fabrication approach. The method is implemented as prototype design tools in MatLAB, C++, GhPython, and Python and demonstrated through cutting of expanded polystyrene foam design...

ANALISIS FLUKTUASI DOLLAR AMERIKA SERIKAT TERHADAP RUPIAH DI SAAT DAN SETELAH KRISIS SUBPRIME MORTGAGE 2007 - 2013

Directory of Open Access Journals (Sweden)

Gustiyan Taufik Mahardika

2015-10-01

Full Text Available In a floating system, exchange rates fluctuate due to macroeconomic conditions that occur. Due to the uncertainty caused by economic shocks or financial crises such as subprime mortgage crisis, fluctuation analysis can be used to minimize the risks that arise in business that involve exchange rates such as export/import or hedge funds. This study aims to analyze the fluctuations in the exchange rate during and after the subprime mortgage crisis 2007 – 2013 in order to give a better understanding on the dynamics of the exchange rate. By analyzing the dynamics, individuals or companies that make the currency as a component in its business can then decide the right policy to implement. Analyses were performed using an error correction model (ECM for nominal (NER and real exchange rate (RER. The variables that are proven significant for NER are money supply (JUB, current account (CAB, economic growth (EGROW, and the nominal central bank rate (NBIRATE. The dummy crisis variable did not have a significant effect on the NER, while the CAB affect NER in the short run only, and EGROW affect NER in the long run only.DOI: 10.15408/sjie.v3i2.2060

Experimental research on the durability cutting tools for cutting-off steel profiles

Directory of Open Access Journals (Sweden)

Cristea Alexandru

2017-01-01

Full Text Available The production lines used for manufacturing U-shaped profiles are very complex and they must have high productivity. One of the most important stages of the fabrication process is the cutting-off. This paper presents the experimental research and analysis of the durability of the cutting tools used for cutting-off U-shaped metal steel profiles. The results of this work can be used to predict the durability of the cutting tools.

Stochastic optimization of subprime residential mortgage loan funding and its risks / by B. de Waal

OpenAIRE

De Waal, Bernadine

2010-01-01

The subprime mortgage crisis (SMC) is an ongoing housing and nancial crisis that was triggered by a marked increase in mortgage delinquencies and foreclosures in the U.S. It has had major adverse consequences for banks and nancial markets around the globe since it became apparent in 2007. In our research, we examine an originator's (OR's) nonlinear stochastic optimal control problem related to choices regarding deposit inflow rates and marketable securities allocation. Here, ...

Love Wave Ultraviolet Photodetector Fabricated on a TiO2/ST-Cut Quartz Structure

Directory of Open Access Journals (Sweden)

Walter Water

2014-01-01

Full Text Available A TiO2 thin film deposited on a 90° rotated 42°45′ ST-cut quartz substrate was applied to fabricate a Love wave ultraviolet photodetector. TiO2 thin films were grown by radio frequency magnetron sputtering. The crystalline structure and surface morphology of TiO2 thin films were examined using X-ray diffraction, scanning electron microscope, and atomic force microscope. The effect of TiO2 thin film thickness on the phase velocity, electromechanical coupling coefficient, temperature coefficient of frequency, and sensitivity of ultraviolet of devices was investigated. TiO2 thin film increases the electromechanical coupling coefficient but decreases the temperature coefficient of frequency for Love wave propagation on the 90° rotated 42°45′ ST-cut quartz. For Love wave ultraviolet photodetector application, the maximum insertion loss shift and phase shift are 2.81 dB and 3.55 degree at the 1.35-μm-thick TiO2 film.

Error Analysis of 3D Metal Micromold Fabricated by Femtosecond Laser Cutting and Microelectric Resistance Slip Welding

Directory of Open Access Journals (Sweden)

Bin Xu

2013-01-01

Full Text Available We used micro-double-staged laminated object manufacturing process (micro-DLOM to fabricate 3D micromold. Moreover, the error of the micro-DLOM was also studied. Firstly, we got the principle error of the micro-DLOM. Based on the mathematical expression, it can be deduced that the smaller the opening angle α and the steel foil thickness h are, the smaller the principle error δ is. Secondly, we studied the error of femtosecond laser cutting. Through the experimental results, we know that the error of femtosecond laser cutting is 0.5 μm under 110 mW femtosecond laser power, 100 μm/s cutting speed, and 0.75 μm dimension compensation. Finally, we researched the error of microelectric resistance slip welding. Based on the research results, we can know that the minimum error of microcavity mold in the height direction is only 0.22 μm when welding voltage is 0.21 V and the number of slip welding discharge is 160.

Fabric circuits and method of manufacturing fabric circuits

Science.gov (United States)

Chu, Andrew W. (Inventor); Dobbins, Justin A. (Inventor); Scully, Robert C. (Inventor); Trevino, Robert C. (Inventor); Lin, Greg Y. (Inventor); Fink, Patrick W. (Inventor)

2011-01-01

A flexible, fabric-based circuit comprises a non-conductive flexible layer of fabric and a conductive flexible layer of fabric adjacent thereto. A non-conductive thread, an adhesive, and/or other means may be used for attaching the conductive layer to the non-conductive layer. In some embodiments, the layers are attached by a computer-driven embroidery machine at pre-determined portions or locations in accordance with a pre-determined attachment layout before automated cutting. In some other embodiments, an automated milling machine or a computer-driven laser using a pre-designed circuit trace as a template cuts the conductive layer so as to separate an undesired portion of the conductive layer from a desired portion of the conductive layer. Additional layers of conductive fabric may be attached in some embodiments to form a multi-layer construct.

Contagion Effects of US Subprime Crisis on ASEAN-5 Stock Markets: Evidence from MGARCH-DCC Application

OpenAIRE

Chunxiu, Ma; Masih, Mansur

2014-01-01

We attempted to investigate the contagion effects of the US subprime crisis on ASEAN-5 stock markets [including Malaysia (conventional and Islamic), Thailand, Singapore, Indonesia, Philippines] by applying MGARCH-DCC through the period of January 1, 2004 to July 5, 2012 on daily stock indices returns, and also Continuous Wavelet Transform coherence method through the period of January 1, 2006 to December 31, 20091 on daily stock indices returns. This is motivated by the fact that the 2007-200...

Stock Market Linkages: Evidence From The US, China And India During The Subprime Crisis

Directory of Open Access Journals (Sweden)

Singh Amanjot

2015-06-01

Full Text Available The Subprime crisis spillovered the returns and volatility from the US stock market to the other integrated economies. The present study attempts to analyze the stock market linkages between the US, India and China, especially during the US subprime Crisis. The technique of Tri-Variate Vector Autoregression and the Spillover Index has been employed so as to analyze the relations during the time period 2007 to 2009. To estimate the time varying risk parameters, the technique of Threshold Generalized Autoregressive Conditional Heteroskedastic [TGARCH (1,1] model has been used. A uni-directional causality has been observed from the US market to the Indian and Chinese market, whereas another unidirectional causality has also been spotted running from the Chinese market to the Indian market in the context of stock market returns during the crisis period. A unidirectional volatility spillover from the US to the Indian market and from the Indian to the Chinese market has been found to be significant. As per the volatility Spillover Index, the cross market impact on the volatility reduces over a time period 2007-2009, due to the increased impact of the past volatility and the presence of 'leverage effect'. The falling returns added to the volatility in the respective markets. The efficient tests of causality inspired by Hill (2007 reported an indirect impact of the US market volatility on the Chinese market via Indian. The portfolio managers should discount this information well ahead of time to maintain the portfolio values by taking positions in futures and options market.

Fabrication of high quality GaAs-on-insulator via ion-cut of epitaxial GaAs/Ge heterostructure

Energy Technology Data Exchange (ETDEWEB)

Chang, Yongwei; Zhang, Miao [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Deng, Chuang; Men, Chuanling [School of Energy and Power Engineering, University of Shanghai for Science and Technology, Shanghai 200093 (China); Chen, Da [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Zhu, Lei; Yu, Wenjie; Wei, Xing [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Di, Zengfeng, E-mail: zfdi@mail.sim.ac.cn [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China); Wang, Xi [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Chinese Academy of Sciences, Shanghai 200050 (China)

2015-08-15

Highlights: • GaAs-on-insulator has been achieved by integrating of epitaxy, ion-cut and selective chemical etching. • Superior to the direct ion-cut of bulk GaAs layer with the H implantation fluence 2.0 × 10{sup 17} cm{sup −2}, the fabrication of GaAs-on-insulator by the transfer of GaAs/Ge heterostructure only needs H implantation fluence as low as 0.8 × 10{sup 17} cm{sup −2}. • The crystalline quality of the top GaAs layer of the final GaAs-on-insulator wafer is not affected by the implantation process and comparable to the as-grown status. - Abstract: Due to the extraordinary electron mobility, III–V compounds are considered as the ideal candidate channel materials for future electronic devices. In this study, a novel approach for the fabrication of high-crystalline quality GaAs-on-insulator has been proposed by integrating of ion-cut and selective chemical etching. GaAs layer with good crystalline quality has been epitaxially grown on Ge by molecular beam epitaxy (MBE). With H implantation and wafer bonding process, the GaAs/Ge heterostructure is transferred onto silicon dioxide wafer after the proper thermal treatment. Superior to the direct ion-cut of GaAs layer, which requires the H implantation fluence as high as 2.0 × 10{sup 17} cm{sup −2}, the transfer of GaAs/Ge heterostructure in the present study only needs the implantation of 0.8 × 10{sup 17} cm{sup −2} H ions. GaAs-on-insulator structure was successfully achieved by the selective chemical etching of defective Ge layer using SF{sub 6} plasma. As the GaAs/Ge heterostructure can be easily epitaxy grown on silicon platform, the proposed approach for GaAs-on-insulator manufacturing is rather compatible with mature Si integrated circuits (ICs) technology and thus can be integrated to push the microelectronic technology to post-Si era.

Fabrication of high quality GaAs-on-insulator via ion-cut of epitaxial GaAs/Ge heterostructure

International Nuclear Information System (INIS)

Chang, Yongwei; Zhang, Miao; Deng, Chuang; Men, Chuanling; Chen, Da; Zhu, Lei; Yu, Wenjie; Wei, Xing; Di, Zengfeng; Wang, Xi

2015-01-01

Highlights: • GaAs-on-insulator has been achieved by integrating of epitaxy, ion-cut and selective chemical etching. • Superior to the direct ion-cut of bulk GaAs layer with the H implantation fluence 2.0 × 10 17 cm −2 , the fabrication of GaAs-on-insulator by the transfer of GaAs/Ge heterostructure only needs H implantation fluence as low as 0.8 × 10 17 cm −2 . • The crystalline quality of the top GaAs layer of the final GaAs-on-insulator wafer is not affected by the implantation process and comparable to the as-grown status. - Abstract: Due to the extraordinary electron mobility, III–V compounds are considered as the ideal candidate channel materials for future electronic devices. In this study, a novel approach for the fabrication of high-crystalline quality GaAs-on-insulator has been proposed by integrating of ion-cut and selective chemical etching. GaAs layer with good crystalline quality has been epitaxially grown on Ge by molecular beam epitaxy (MBE). With H implantation and wafer bonding process, the GaAs/Ge heterostructure is transferred onto silicon dioxide wafer after the proper thermal treatment. Superior to the direct ion-cut of GaAs layer, which requires the H implantation fluence as high as 2.0 × 10 17 cm −2 , the transfer of GaAs/Ge heterostructure in the present study only needs the implantation of 0.8 × 10 17 cm −2 H ions. GaAs-on-insulator structure was successfully achieved by the selective chemical etching of defective Ge layer using SF 6 plasma. As the GaAs/Ge heterostructure can be easily epitaxy grown on silicon platform, the proposed approach for GaAs-on-insulator manufacturing is rather compatible with mature Si integrated circuits (ICs) technology and thus can be integrated to push the microelectronic technology to post-Si era

Carcass fabrication yields of beef steers supplemented zilpaterol hydrochloride and offered ad libitum or maintenance energy intake.

Science.gov (United States)

Schmitz, Angela N; Walter, Lee-Anne J; Nichols, Wade T; Hutcheson, John P; Lawrence, Ty E

2018-06-04

An experiment was conducted to evaluate the fabrication yields of carcasses from beef steers supplemented zilpaterol hydrochloride (ZH) and fed at maintenance (MA) or ad libitum (AB) intake levels. Beef steers (n = 56) from a common sire were blocked (n = 28 per block) by terminal growth implant and sorted into pairs by BW. Four pairs (n = 8) were harvested on day 0; the remaining 24 pairs (n = 48) were assigned to a dietary intake level (MA or AB) and days on feed (28 or 56 d). Within pairs of MA or AB intakes, steers harvested on day 56 were randomly assigned to supplementation of ZH (90 mg·d-1 per steer) for 20 d followed by a withdrawal period of 4 d or control (C). Steers (BW = 603.5 ± 48.1 kg) were harvested at a commercial processing facility. After a 24-h chill period, standard USDA grading procedures were used to derive a calculated yield grade and quality grade. Following grading, left carcass sides were transported to the West Texas A&M University Meat Laboratory for fabrication. Each side was fabricated into subprimals to determine individual red meat yield (RMY), trimmable fat yield (TFY), and bone yield (BY). A mixed model was used for analysis; fixed effects included treatment combinations and random effects included block and pairs. Single df contrasts tested day 0 vs. 28, day 0 vs. 56, day 28 vs. 56, MA vs. AB, and C vs. ZH. Yield of chuck eye roll differed (P = 0.05) by days on feed (0 d = 4.14, 28 d = 4.11, 56 d = 4.55%). Similarly, eye of round yield was impacted (P = 0.02) by days on feed (0 d = 1.51, 28 d = 1.37, 56 d = 1.36%). Additionally, brisket yield was altered (P < 0.01) by days on feed (0 d = 4.08, 28 d = 3.56, 56 d = 3.48%) and treatment (C = 3.34, ZH = 3.61%). For remaining subprimals, no differences (P ≥ 0.15) were detected. Furthermore, results indicated that RMY tended (P = 0.07) to differ by treatment (C = 61.35, ZH = 63.67%). Comparatively, TFY was impacted (P = 0.04) by intake (MA = 20.44, AB = 23.33%). Results from this

Demonstration of Laser Cutting System for Tube Specimen

Energy Technology Data Exchange (ETDEWEB)

Jin, Y. G.; Kim, G. S.; Heo, G. S.; Baik, S. J.; Kim, H. M.; Ahn, S. B. [KAERI, Daejeon (Korea, Republic of)

2016-05-15

The oxide layer removal system was also developed because the oxide layer on the surface of the irradiated fuel cladding and components interrupted the applying the electric current during the processing. However, it was found that the mechanical testing data of the irradiated specimens with removal of oxide layer was less reliable than the specimens with oxide layer . The laser cutting system using Nd:YAG with fiber optic beam delivery has great potential in material processing applications of the irradiated fuel cladding and components due to non-contact process. Thus, the oxide layer doesn't interrupt the fabrication process during the laser cutting system. In the present study, the laser cutting system was designed to fabricate the mechanical testing specimens from the unirradiated fuel cladding with and without oxide. The feasibility of the laser cutting system was demonstrated for the fabrication of various types of unirradiated specimens. The effect of surface oxide layer was also investigated for machining process of the zirlo fuel cladding and it was found that laser beam machining could be a useful tool to fabricate the specimens with surface oxide layer. Based on the feasibility studies and demonstration, the design of the laser cutting machine for fully or partially automatic and remotely operable system will be proposed and made.

Dual-component video image analysis system (VIASCAN) as a predictor of beef carcass red meat yield percentage and for augmenting application of USDA yield grades.

Science.gov (United States)

Cannell, R C; Tatum, J D; Belk, K E; Wise, J W; Clayton, R P; Smith, G C

1999-11-01

An improved ability to quantify differences in the fabrication yields of beef carcasses would facilitate the application of value-based marketing. This study was conducted to evaluate the ability of the Dual-Component Australian VIASCAN to 1) predict fabricated beef subprimal yields as a percentage of carcass weight at each of three fat-trim levels and 2) augment USDA yield grading, thereby improving accuracy of grade placement. Steer and heifer carcasses (n = 240) were evaluated using VIASCAN, as well as by USDA expert and online graders, before fabrication of carcasses to each of three fat-trim levels. Expert yield grade (YG), online YG, VIASCAN estimates, and VIASCAN estimated ribeye area used to augment actual and expert grader estimates of the remaining YG factors (adjusted fat thickness, percentage of kidney-pelvic-heart fat, and hot carcass weight), respectively, 1) accounted for 51, 37, 46, and 55% of the variation in fabricated yields of commodity-trimmed subprimals, 2) accounted for 74, 54, 66, and 75% of the variation in fabricated yields of closely trimmed subprimals, and 3) accounted for 74, 54, 71, and 75% of the variation in fabricated yields of very closely trimmed subprimals. The VIASCAN system predicted fabrication yields more accurately than current online yield grading and, when certain VIASCAN-measured traits were combined with some USDA yield grade factors in an augmentation system, the accuracy of cutability prediction was improved, at packing plant line speeds, to a level matching that of expert graders applying grades at a comfortable rate.

From Subprime and Eurozone Crisis with Full Speed into the Next Financial Crisis

Directory of Open Access Journals (Sweden)

Strašek Sebastjan

2017-09-01

Full Text Available This paper offers an analysis of the road from subprime and eurozone crisis to the elements of a new systemic crisis. Our aim is to research common issues that accompany each of these crises and to explore elements that hint that the financial systems are moving toward a new crisis. By holding short-term interest rates near zero, the central banks have encouraged malinvestment and speculation. Fuelling the bubble is the fear of missing out on trade. We find that actual events and movements on security markets follow a typical pattern, which indicates a serious threat for the next financial crisis. We also find enough signs that old crises lessons haven’t been learned.

Polyester Apparel Cutting Waste as Insulation Material

OpenAIRE

Trajković, Dušan; Jordeva, Sonja; Tomovska, Elena; Zafirova, Koleta

2017-01-01

Polyester waste is the dominant component of the clothing industry waste stream, yet its recycling in this industry is rarely addressed. This paper proposes using polyester cutting waste as an insulation blanket for roofing and buildings’ internal walls in order to reduce environmental pollution. The designed textile structures used waste cuttings from different polyester fabrics without opening the fabric to fibre. Thermal insulation, acoustic insulation, fire resistance and biodegradation o...

Fabrication of Ge-on-insulator wafers by Smart-CutTM with thermal management for undamaged donor Ge wafers

Science.gov (United States)

Kim, Munho; Cho, Sang June; Jayeshbhai Dave, Yash; Mi, Hongyi; Mikael, Solomon; Seo, Jung-Hun; Yoon, Jung U.; Ma, Zhenqiang

2018-01-01

Newly engineered substrates consisting of semiconductor-on-insulator are gaining much attention as starting materials for the subsequent transfer of semiconductor nanomembranes via selective etching of the insulating layer. Germanium-on-insulator (GeOI) substrates are critically important because of the versatile applications of Ge nanomembranes (Ge NMs) toward electronic and optoelectronic devices. Among various fabrication techniques, the Smart-CutTM technique is more attractive than other methods because a high temperature annealing process can be avoided. Another advantage of Smart-CutTM is the reusability of the donor Ge wafer. However, it is very difficult to realize an undamaged Ge wafer because there exists a large mismatch in the coefficient of thermal expansion among the layers. Although an undamaged donor Ge wafer is a prerequisite for its reuse, research related to this issue has not yet been reported. Here we report the fabrication of 4-inch GeOI substrates using the direct wafer bonding and Smart-CutTM process with a low thermal budget. In addition, a thermo-mechanical simulation of GeOI was performed by COMSOL to analyze induced thermal stress in each layer of GeOI. Crack-free donor Ge wafers were obtained by annealing at 250 °C for 10 h. Raman spectroscopy and x-ray diffraction (XRD) indicated similarly favorable crystalline quality of the Ge layer in GeOI compared to that of bulk Ge. In addition, Ge p-n diodes using transferred Ge NM indicate a clear rectifying behavior with an on and off current ratio of 500 at ±1 V. This demonstration offers great promise for high performance transferrable Ge NM-based device applications.

Laser cutting or water-jet cutting. Laser setsudan ka water-jet setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Yamada, T. (Shibuya Kogyo Co. Ltd., Ishikawa (Japan))

1991-05-01

The recent spread of carbon oxide laser cutter is so startlingly fast, but at the same time, water jet cutting using ultra high pressure water stream is drawing attention as it has identical characteristics, and opens the way to cutting materials that have been hitherto difficult to cut. The authors, who are fabricators of cutters of both types, gave the comparisons and explanations on several examples referring to materials that can be cut, cutting accuracy, speed, shape and thermal effects to cut face, and running cost in detail. However, simple comparison is difficult. For instance, cutting 6 mm thick SUS sheet costs a running cost of 65 yen per meter in laser cutting, and 535 yen per meter in water jet cutting, but this situation is often reversed when other material or sheet thickness is selected. The actual situation in the sheet metal processing industry at the present time is that it uses by far more laser processing machines, and uses water jet cutters to supplement for cutting materials more difficult to cut. 10 figs., 3 tabs.

Meat quality and cut yield of pigs slaughtered over 100kg live weight

Directory of Open Access Journals (Sweden)

T.M. Bertol

2015-08-01

Full Text Available Meat quality and cut yield of pigs slaughtered between 100 and 150kg live weight were evaluated. Pigs (417 Agroceres PIC barrows and gilts were fed a daily allowance of 2.8kg per head from 80kg until 100.71±0.85, 118.58±0.99, 134.07±1.18 or 143.90±1.24kg live weight. Seventy-one pigs were used for the evaluation of primal and subprimal cuts. There was no interaction between sex and slaughter weight for any of the evaluated parameters. Ham, shoulder, and loin weights linearly increased (P<0.01; R2: 84.3-93.2% with increasing slaughter weight, which, however, had little effect on primal cuts meat yield. Increasing slaughter weight promoted a linear (P<0.05 and a quadratic (P<0.01 increase of red/green coordinate (a* value of the loin and ham, respectively. Shear force showed a quadratic response (P<0.05, with minimum value estimated at 122kg slaughter weight. It was concluded that, under the applied management, increasing slaughter weight increased the volume of meat, but had little effect on meat yield. The meat of pigs slaughtered at heavier weights showed more intense red color and the same intramuscular fat content as lighter pigs, while tenderness was slightly affected.

Simple and cost-effective fabrication of microvalve arrays in PDMS using laser cut molds with application to C. elegans manipulation in microfluidics

International Nuclear Information System (INIS)

Samuel, R; Gale, B K; Thacker, C M; Maricq, A V

2014-01-01

We present a new fabrication protocol for fabricating pneumatically controlled microvalve arrays (consisting of 100 s of microvalves) in PDMS substrates. The protocol utilizes rapid and cost-effective fabrication of molds using laser cutting of adhesive vinyl tapes and replica molding of PDMS. Hence the protocol is fast, simple and avoids cleanroom use. The results show that effective doormat-style microvalves can be easily fabricated in arrays by manipulating the stiffness of the actuating membrane through varying the valve-chamber area/shape. Three frequently used valve-chamber shapes (circle, square and capsule) were tested and all showed advantages in different situations. Circular valve chambers were best for small valves, square valves were best for medium-sized valves, and the capsule valves were best for larger valves. An application of this protocol has been demonstrated in the fabrication of a microfluidic 32-well plate for high-throughput manipulation of C. elegans for biomedical research. (paper)

EFEITO SUBPRIME NA DISTRIBUIÇÃO DE DIVIDENDOS EM PORTUGAL

Directory of Open Access Journals (Sweden)

Luís António Gomes Almeida

2015-11-01

Full Text Available A política dos dividendos é um dos temas que tem concebido mais trabalhos teóricos e empíricos na área das finanças empresariais, pois dividendos são considerados uma das decisões financeiras empresariais mais importantes na vida das empresas, estando associados às políticas de investimento e de financiamento, e os seus determinantes não são de escolha unânime. No intuito de dar mais um contributo na resolução desta problemática, testam-se empiricamente o efeito subprime com a inclusão de uma dummy, e outros  determinantes financeiros pela aplicação do método de regressão linear múltipla, às empresas não financeiras cotadas na Euronext Lisbon, no período de 1997 e 2013. Os resultados sugerem a influência do valor de mercado, resultados e rendibilidade,  oportunidades de crescimento e de investimento no montante de dividendos distribuídos pela empresa.

Automated Laser Cutting In Three Dimensions

Science.gov (United States)

Bird, Lisa T.; Yvanovich, Mark A.; Angell, Terry R.; Bishop, Patricia J.; Dai, Weimin; Dobbs, Robert D.; He, Mingli; Minardi, Antonio; Shelton, Bret A.

1995-01-01

Computer-controlled machine-tool system uses laser beam assisted by directed flow of air to cut refractory materials into complex three-dimensional shapes. Velocity, position, and angle of cut varied. In original application, materials in question were thermally insulating thick blankets and tiles used on space shuttle. System shapes tile to concave or convex contours and cuts beveled edges on blanket, without cutting through outer layer of quartz fabric part of blanket. For safety, system entirely enclosed to prevent escape of laser energy. No dust generated during cutting operation - all material vaporized; larger solid chips dislodged from workpiece easily removed later.

UJI INTEGRASI DAN CONTAGION EFFECT PASAR MODAL PADA LIMA NEGARA ASEAN (RISET EMPIRIS PASCA TERJADINYA KRISIS SUBPRIME MORTGAGE DAN KRISIS YUNANI

Directory of Open Access Journals (Sweden)

Tarsisius Renald Suganda

2016-10-01

Full Text Available Financial market comovement in ASEAN main member countries is still attractive to scrunitized, because this area is vulnerable to the impact on a global economic event. This study examined capital market integration of five ASEAN main members (Indonesia, Singapore, Malaysia, Philippines, and Thailand by using September 2008—30 April 2013 data period. This period will divided into the post 2008 Subprime Mortgage crisis period and the post 2010 Greece crisis period. Vector Autoregressive (VAR was used to test the comovement occurance among these capital markets and Granger Causality Test was used to analyze the contagion effect among these capital markets. The finding shows that the comovement was occurred among Indonesia, Malay-sia, Singapore and Thailand’s capital market during September 2008 to 30 April 2013 period. The comovement was still occured after 2008 Subpime Mortgage crisis period and 2010 Greece crisis period, although there is country namely Philippines which did not have the comovement at all against the other countries. Further-more, the finding shows that Indonesia capital market gives contagion effect to other ASEAN countries after 2008 Subprime Mortgage crisis and Greece financial crisis.

Experimental Investigation on Cutting Characteristics in Nanometric Plunge-Cutting of BK7 and Fused Silica Glasses.

Science.gov (United States)

An, Qinglong; Ming, Weiwei; Chen, Ming

2015-03-27

Ductile cutting are most widely used in fabricating high-quality optical glass components to achieve crack-free surfaces. For ultra-precision machining of brittle glass materials, critical undeformed chip thickness (CUCT) commonly plays a pivotal role in determining the transition point from ductile cutting to brittle cutting. In this research, cutting characteristics in nanometric cutting of BK7 and fused silica glasses, including machined surface morphology, surface roughness, cutting force and specific cutting energy, were investigated with nanometric plunge-cutting experiments. The same cutting speed of 300 mm/min was used in the experiments with single-crystal diamond tool. CUCT was determined according to the mentioned cutting characteristics. The results revealed that 320 nm was found as the CUCT in BK7 cutting and 50 nm was determined as the size effect of undeformed chip thickness. A high-quality machined surface could be obtained with the undeformed chip thickness between 50 and 320 nm at ductile cutting stage. Moreover, no CUCT was identified in fused silica cutting with the current cutting conditions, and brittle-fracture mechanism was confirmed as the predominant chip-separation mode throughout the nanometric cutting operation.

Cross-correlation matrix analysis of Chinese and American bank stocks in subprime crisis

International Nuclear Information System (INIS)

Zhu Shi-Zhao; Li Xin-Li; Zhang Wen-Qing; Wang Bing-Hong; Nie Sen; Yu Gao-Feng; Han Xiao-Pu

2015-01-01

In order to study the universality of the interactions among different markets, we analyze the cross-correlation matrix of the price of the Chinese and American bank stocks. We then find that the stock prices of the emerging market are more correlated than that of the developed market. Considering that the values of the components for the eigenvector may be positive or negative, we analyze the differences between two markets in combination with the endogenous and exogenous events which influence the financial markets. We find that the sparse pattern of components of eigenvectors out of the threshold value has no change in American bank stocks before and after the subprime crisis. However, it changes from sparse to dense for Chinese bank stocks. By using the threshold value to exclude the external factors, we simulate the interactions in financial markets. (paper)

First-Order Parametric Model of Reflectance Spectra for Dyed Fabrics

Science.gov (United States)

2016-02-19

Ripstop fabric was cut from the roll and placed under a Freeman Schwabe cutting press . A 2”x2” Fremont steel rule cutting die was used in combination...with the mechanical press to make 20, 2”x2” fabric samples. Dye-fabric samples were prepared by pipetting 1 mL of each dye solution onto the center of...monochromator slewing. For UV-Vis wavelengths, the slit width was fixed at 4 nm. For NIR-SWIR wavelengths, the slit width was set to “ Servo ” mode, which

Aspects of plasma cutting in AISI 321 stainless steel

International Nuclear Information System (INIS)

Souza Barros, I. de; Cardoso, P.E.

1985-10-01

The utilization of plasma cutting process in AISI 321 stainless steel heavy plates for fabricating nozzles for nuclear reactors was evaluated. The effect of current, electric potential and cutting speed are studied. The superficial irregularity and the microstructure of the zone affected by the cut were analyzed by measurements of roughness, optical metallography and microhardness. (E.G.) [pt

One-step patterning of hollow microstructures in paper by laser cutting to create microfluidic analytical devices.

Science.gov (United States)

Nie, Jinfang; Liang, Yuanzhi; Zhang, Yun; Le, Shangwang; Li, Dunnan; Zhang, Songbai

2013-01-21

In this paper, we report a simple, low-cost method for rapid, highly reproductive fabrication of paper-based microfluidics by using a commercially available, minitype CO(2) laser cutting/engraving machine. This method involves only one operation of cutting a piece of paper by laser according to a predesigned pattern. The hollow microstructures formed in the paper are used as the 'hydrophobic barriers' to define the hydrophilic flowing paths. A typical paper device on a 4 cm × 4 cm piece of paper can be fabricated within ∼7-20 s; it is ready for use once the cutting process is finished. The main fabrication parameters such as the applied current and cutting rate of the laser were optimized. The fabrication resolution and multiplexed analytical capability of the hollow microstructure-patterned paper were also characterized.

Irradiated multilayer film for primal meat packaging

International Nuclear Information System (INIS)

Lustig, S.; Schuetz, J.M.; Vicik, S.J.

1987-01-01

This patent deals with a heat-shrinkable, multilayer film suitable for use in fabricating bags for packaging primal and sub-primal meat cuts and processed meats. The multilayer film has a first outer layer of an ethylene-vinyl acetate copolymer, a core layer of a barrier film comprising vinylidene chloride-methyl acrylate copolymer, and a second outer layer of an ethylene-vinyl acetate copolymer. The multilayer film is preferably made by co-extrusion of the layers, and then it is biaxially stretched. After biaxial stretching, the multilayer film is irradiated to a dosage level of between 1 megarad and 5 megarads and heat-sealed in the form of a bag. The bag has improved storage stability characteristics

Laser cutting fabrication of magnetic components

International Nuclear Information System (INIS)

Neuenschwander, R.T.; Ricardo, A.; Rodrigues, D.; Talarico, F.W.B.; Goncalves da Silva, C.E.T.

1992-01-01

Dipole, quadrupole and sextupole prototypes for the LNLS storage ring have been fabricated using 1.5 mm thick, low carbon steel laminations, with the aid of CO 2 laser cutter, reaching an overall dimensional accuracy of ±0.02 mm (standard deviation). The relevant aspects of the technique are presented, together with the results of magnetic and dimensional measurements. The possibility of mass producing these components with the technique is also analyzed. (author) 2 refs.; 6 figs

Development of the spent fuel rod cutting device using the blade cutters

International Nuclear Information System (INIS)

Jung, Jae Hoo; Yoon, Ji Sup; Hong, Dong Hee; Kim, Young Hwan; Park, Gee Yong; Kim, Do Woo

2000-11-01

A spent fuel rod cutting device is to cut a spent nuclear fuel rod to optimal size for consequent decladding operation. In this paper, various properties of fuel rod, such as a dimension and material of zircaloy tubes and fuel pellets, are investigated. Also, commercially available cutting method and tools is investigated in terms of its performance. As a result, the blade cutter is selected for the design. In order to fabricate the durable blade cutter, various materials are analyzed in terms of material properties, cutter shape, and heat treatment method, etc. Also, the durability of this tool is tested by cutting the SUS tubes and zircaloy tubes. In the device design, the remote maintainability is considered so that the modularized design is accomplished. Also, the other factors considered in the design are the round shape sustainability at the cut surface, the amount of debris generation, and the fire risk, etc. Considering these design consideration, the spent fuel rod cutting device is fabricated and tested

Innovative retail merchandising strategies to accommodate for the growing trend of heavier carcass weights in the United States.

Science.gov (United States)

West, S E; Nicholson, K L; Nicholson, J D W; Griffin, D B; Lawrence, T E; Wasser, B E; Savell, J W

2011-08-01

Three subprimals from beef carcasses, Average (mean=340.6kg) and Heavy weight (mean=461.6kg), were cut using Innovative versus Conventional cutting styles. Longer (Pmerchandise heavyweight beef must account for the decreased primary saleable yields and increased labor requirements through increased retail pricing. Copyright © 2011 Elsevier Ltd. All rights reserved.

CO2 Laser Cutting of Hot Stamping Boron Steel Sheets

OpenAIRE

Pasquale Russo Spena

2017-01-01

This study investigates the quality of CO2 laser cutting of hot stamping boron steel sheets that are employed in the fabrication of automotive body-in-white. For this purpose, experimental laser cutting tests were conducted on 1.2 mm sheets at varying levels of laser power, cutting speed, and oxygen pressure. The resulting quality of cut edges was evaluated in terms of perpendicularity tolerance, surface irregularity, kerf width, heat affected zone, and dross extension. Experimental tests wer...

On the source of stochastic volatility: Evidence from CAC40 index options during the subprime crisis

Science.gov (United States)

Slim, Skander

2016-12-01

This paper investigates the performance of time-changed Lévy processes with distinct sources of return volatility variation for modeling cross-sectional option prices on the CAC40 index during the subprime crisis. Specifically, we propose a multi-factor stochastic volatility model: one factor captures the diffusion component dynamics and two factors capture positive and negative jump variations. In-sample and out-of-sample tests show that our full-fledged model significantly outperforms nested lower-dimensional specifications. We find that all three sources of return volatility variation, with different persistence, are needed to properly account for market pricing dynamics across moneyness, maturity and volatility level. Besides, the model estimation reveals negative risk premium for both diffusive volatility and downward jump intensity whereas a positive risk premium is found to be attributed to upward jump intensity.

Wire electric-discharge machining and other fabrication techniques

Science.gov (United States)

Morgan, W. H.

1983-01-01

Wire electric discharge machining and extrude honing were used to fabricate a two dimensional wing for cryogenic wind tunnel testing. Electric-discharge cutting is done with a moving wire electrode. The cut track is controlled by means of a punched-tape program and the cutting feed is regulated according to the progress of the work. Electric-discharge machining involves no contact with the work piece, and no mechanical force is exerted. Extrude hone is a process for honing finish-machined surfaces by the extrusion of an abrasive material (silly putty), which is forced through a restrictive fixture. The fabrication steps are described and production times are given.

ANALYZING CONTAGION FROM THE U.S. SUBPRIME MORTGAGE-BACKED SECURITIES MARKET

Directory of Open Access Journals (Sweden)

Lisa Sheenan

2017-12-01

Full Text Available This paper analyzes contagion from the U.S. subprime mortgage-backed securities market, represented by the ABX.HE indices, to several fixed income, equity and volatility markets in line with seminal literature on the subject. We analyze ‘spliced’ data set constructed in line with the literature, along with two traded ABX.HE indexes. A VAR framework is employed, firstly to extend existing analysis to include 2009, and then to analyze two traded indexes. In order to test the sensitivity of these results ABX returns are then included as an eighth endogenous variable in the VAR. Principal component analysis is employed to reduce the dimensionality of the data. The main principal component obtained is then included as an exogenous variable in the VAR framework and the sensitivity of these results is tested by including this principal component as an eighth endogenous variable. The results indicate evidence of contagion from the ABX indexes during the crisis of 2007-2009 but the source and intensity of this contagion varies across indexes. This highlights the differences across the three ABX data sets analyzed and suggests that splicing the ABX index may impact the results obtained. It also provides evidence that the traded ABX indexes are heterogeneous assets with varying sensitivities to risk factors during the crisis.

Ag-catalysed cutting of multi-walled carbon nanotubes

International Nuclear Information System (INIS)

La Torre, A; Rance, G A; Miners, S A; Lucas, C Herreros; Smith, E F; Giménez-López, M C; Khlobystov, A N; Fay, M W; Brown, P D; Zoberbier, T; Kaiser, U

2016-01-01

In this work, the cutting of carbon nanotubes is investigated using silver nanoparticles deposited on arc discharge multi-walled carbon nanotubes. The composite is subsequently heated in air to fabricate shortened multi-walled nanotubes. Complementary transmission electron microscopy and spectroscopy techniques shed light on the cutting mechanism. The nanotube cutting is catalysed by the fundamental mechanism based on the coordination of the silver atoms to the π-bonds of carbon nanotubes. As a result of the metal coordination, the strength of the carbon–carbon bond is reduced, promoting the oxidation of carbon at lower temperature when heated in air, or lowering the activation energy required for the removal of carbon atoms by electron beam irradiation, assuring in both cases the cutting of the nanotubes. (paper)

Near-Infrared Quantum Cutting Long Persistent Luminescence

OpenAIRE

Zou, Zehua; Feng, Lin; Cao, Cheng; Zhang, Jiachi; Wang, Yuhua

2016-01-01

By combining the unique features of the quantum cutting luminescence and long persistent luminescence, we design a new concept called ?near-infrared quantum cutting long persistent luminescence (NQPL)?, which makes it possible for us to obtain highly efficient (>100%) near-infrared long persistent luminescence in theory. Guided by the NQPL concept, we fabricate the first NQPL phosphor Ca2Ga2GeO7:Pr3+,Yb3+. It reveals that both the two-step energy transfer of model (I) and the one-step energy ...

Cross-correlation matrix analysis of Chinese and American bank stocks in subprime crisis

Science.gov (United States)

Zhu, Shi-Zhao; Li, Xin-Li; Nie, Sen; Zhang, Wen-Qing; Yu, Gao-Feng; Han, Xiao-Pu; Wang, Bing-Hong

2015-05-01

In order to study the universality of the interactions among different markets, we analyze the cross-correlation matrix of the price of the Chinese and American bank stocks. We then find that the stock prices of the emerging market are more correlated than that of the developed market. Considering that the values of the components for the eigenvector may be positive or negative, we analyze the differences between two markets in combination with the endogenous and exogenous events which influence the financial markets. We find that the sparse pattern of components of eigenvectors out of the threshold value has no change in American bank stocks before and after the subprime crisis. However, it changes from sparse to dense for Chinese bank stocks. By using the threshold value to exclude the external factors, we simulate the interactions in financial markets. Project supported by the National Natural Science Foundation of China (Grant Nos. 11275186, 91024026, and FOM2014OF001) and the University of Shanghai for Science and Technology (USST) of Humanities and Social Sciences, China (Grant Nos. USST13XSZ05 and 11YJA790231).

Laser cutting system in bridge fabricating line; Kyoryo seisaku line ni okeru laser no setsudan system

Energy Technology Data Exchange (ETDEWEB)

Kitaguchi, Y.; Yokotani, K. [Hitachi Zosen Corp., Osaka (Japan)

1994-11-01

This paper describes the laser cutting system established at a new advanced plant that was constructed by Hitachi Shipbuilding and Engineering Co., Ltd. in 1993. At the plant, the cutting line consists of four NC cutting lines: the plasma cutting machine, gas cutting machine, frame planer, and laser cutting machine. The laser cutting machine is used to cut complex shapes of relatively thin (6 - 16 mm) materials with high accuracy. The machine consists of a 3 kW CO2 laser oscillator mounted gantry type NC cutter and a slat conveyor of about 30 m long, with the maximum cutting width of 3.6 m. The NC cutting machine is provided with the automatic printing function using NC data, marking function, scheduled operation function, steel plate detector, and coordinate rotation function, etc. These functions enable unattended operation of the machine to cut multiple materials. This NC laser cutting line has the same performance data collection function for data during the operating time as other production lines. Therefore, the NC laser cutting line can be subjected to the realtime centralized control together with the other lines. All these technologies have provided high accuracy and efficiency for production as well as an environment in which many female operators can successfully work. 10 figs., 4 tabs.

Extended asymmetric-cut multilayer X-ray gratings.

Science.gov (United States)

Prasciolu, Mauro; Haase, Anton; Scholze, Frank; Chapman, Henry N; Bajt, Saša

2015-06-15

The fabrication and characterization of a large-area high-dispersion blazed grating for soft X-rays based on an asymmetric-cut multilayer structure is reported. An asymmetric-cut multilayer structure acts as a perfect blazed grating of high efficiency that exhibits a single diffracted order, as described by dynamical diffraction throughout the depth of the layered structure. The maximum number of grating periods created by cutting a multilayer deposited on a flat substrate is equal to the number of layers deposited, which limits the size of the grating. The size limitation was overcome by depositing the multilayer onto a substrate which itself is a coarse blazed grating and then polish it flat to reveal the uniformly spaced layers of the multilayer. The number of deposited layers required is such that the multilayer thickness exceeds the step height of the substrate structure. The method is demonstrated by fabricating a 27,060 line pairs per mm blazed grating (36.95 nm period) that is repeated every 3,200 periods by the 120-μm period substrate structure. This preparation technique also relaxes the requirements on stress control and interface roughness of the multilayer film. The dispersion and efficiency of the grating is demonstrated for soft X-rays of 13.2 nm wavelength.

Laser-assisted fabrication of materials

CERN Document Server

Manna, Indranil

2013-01-01

Laser assisted fabrication involves shaping of materials using laser as a source of heat. It can be achieved by removal of materials (laser assisted cutting, drilling, etc.), deformation (bending, extrusion), joining (welding, soldering) and addition of materials (surface cladding or direct laser cladding). This book on ´Laser assisted Fabrication’ is aimed at developing in-depth engineering concepts on various laser assisted macro and micro-fabrication techniques with the focus on application and a review of the engineering background of different micro/macro-fabrication techniques, thermal history of the treated zone and microstructural development and evolution of properties of the treated zone.

DESIGN AND FABRICATION OF MULTI STAGE CUTTING OIL FILTER SYSTEM

OpenAIRE

ABHIJIT S. GETME , ADITENDRA JAISWAL

2018-01-01

Multistage oil filtration system is a system used to filter out all the metallic, non metallic particles from the cutting fluid, which is used during the machining processes. Basic procedures we are using in it are: centrifugal process, magnetic filtration, paper filtration.

Miraculous financial engineering or toxic finance? The genesis of the U.S. subprime mortgage loans crisis and its consequences on the global financial markets and real economy

OpenAIRE

Ivo Pezzuto

2012-01-01

In the fall of 2008, the U.S. subprime mortgage loans defaults have turned into Wall Street’s biggest crisis since the Great Depression. As hundreds of billions in mortgage-related investments went bad, banks became suspicious of one another’s potential undisclosed credit losses and preferred to reduce their exposure in the interbank markets, thus causing interbank interest rates and credit default swaps increases, a liquidity shortage problem and a worsened credit crunch condition to consume...

Mesh joinery: a method for building fabricable structures

OpenAIRE

Cignoni, Paolo; Pietroni, Nico; Malomo, Luigi; Scopigno, Roberto

2015-01-01

Mesh joinery is an innovative method to produce illustrative shape approximations suitable for fabrication. Mesh joinery is capable of producing complex fabricable structures in an efficient and visually pleasing manner. We represent an input geometry as a set of planar pieces arranged to compose a rigid structure by exploiting an efficient slit mechanism. Since slices are planar, a standard 2D cutting system is sufficient to fabricate them.

Effect of micro-scale texturing on the cutting tool performance

Science.gov (United States)

Vasumathy, D.; Meena, Anil

2018-05-01

The present study is mainly focused on the cutting performance of the micro-scale textured carbide tools while turning AISI 304 austenitic stainless steel under dry cutting environment. The texture on the rake face of the carbide tools was fabricated by laser machining. The cutting performance of the textured tools was further compared with conventional tools in terms of cutting forces, tool wear, machined surface quality and chip curl radius. SEM and EDS analyses have been also performed to better understand the tool surface characteristics. Results show that the grooves help in breaking the tool-chip contact leading to a lesser tool-chip contact area which results in reduced iron (Fe) adhesion to the tool.

Development of thick wall welding and cutting tools for ITER

International Nuclear Information System (INIS)

Nakahira, Masataka; Takahashi, Hiroyuki; Akou, Kentaro; Koizumi, Koichi

1998-01-01

The Vacuum Vessel, which is a core component of International Thermonuclear Experimental Reactor (ITER), is required to be exchanged remotely in a case of accident such as superconducting coil failure. The in-vessel components such as blanket and divertor are planned to be exchanged or fixed. In these exchange or maintenance operations, the thick wall welding and cutting are inevitable and remote handling tools are necessary. The thick wall welding and cutting tools for blanket are under developing in the ITER R and D program. The design requirement is to weld or cut the stainless steel of 70 mm thickness in the narrow space. Tungsten inert gas (TIG) arc welding, plasma cutting and iodine laser welding/cutting are selected as primary option. Element welding and cutting tests, design of small tools to satisfy space requirement, test fabrication and performance tests were performed. This paper reports the tool design and overview of welding and cutting tests. (author)

Development of thick wall welding and cutting tools for ITER

Energy Technology Data Exchange (ETDEWEB)

Nakahira, Masataka; Takahashi, Hiroyuki; Akou, Kentaro; Koizumi, Koichi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-04-01

The Vacuum Vessel, which is a core component of International Thermonuclear Experimental Reactor (ITER), is required to be exchanged remotely in a case of accident such as superconducting coil failure. The in-vessel components such as blanket and divertor are planned to be exchanged or fixed. In these exchange or maintenance operations, the thick wall welding and cutting are inevitable and remote handling tools are necessary. The thick wall welding and cutting tools for blanket are under developing in the ITER R and D program. The design requirement is to weld or cut the stainless steel of 70 mm thickness in the narrow space. Tungsten inert gas (TIG) arc welding, plasma cutting and iodine laser welding/cutting are selected as primary option. Element welding and cutting tests, design of small tools to satisfy space requirement, test fabrication and performance tests were performed. This paper reports the tool design and overview of welding and cutting tests. (author)

Is the 2007 US sub-prime financial crisis so different?: An international historical comparison

Directory of Open Access Journals (Sweden)

Reinhart Carmen M.

2009-01-01

Full Text Available The first major financial crisis of the twenty first century involves esoteric instruments, unaware regulators, and skittish investors. It also follows a well-trodden path laid down by centuries of financial folly. Is the 'special' problem of sub-prime mortgages really different? Our examination of the longer historical record finds stunning qualitative and quantitative parallels across a number of standard financial crisis indicators. At this juncture, the book is still open on how the current dislocations in the United States will play out. The precedent found in the aftermath of other episodes suggests that the strains can be quite severe, depending especially on the initial degree of trauma to the financial system (and to some extent, the policy response. The average drop in real per capita output growth is over 2 percent, and it typically takes two years to return to trend. For the five most catastrophic cases (which include episodes in Finland, Japan, Norway, Spain, and Sweden, the drop in annual output growth from peak to trough is over 5 percent, and growth remained well below pre-crisis trend even after three years.

Research of a smart cutting tool based on MEMS strain gauge

Science.gov (United States)

Zhao, Y.; Zhao, Y. L.; Shao, YW; Hu, T. J.; Zhang, Q.; Ge, X. H.

2018-03-01

Cutting force is an important factor that affects machining accuracy, cutting vibration and tool wear. Machining condition monitoring by cutting force measurement is a key technology for intelligent manufacture. Current cutting force sensors exist problems of large volume, complex structure and poor compatibility in practical application, for these problems, a smart cutting tool is proposed in this paper for cutting force measurement. Commercial MEMS (Micro-Electro-Mechanical System) strain gauges with high sensitivity and small size are adopted as transducing element of the smart tool, and a structure optimized cutting tool is fabricated for MEMS strain gauge bonding. Static calibration results show that the developed smart cutting tool is able to measure cutting forces in both X and Y directions, and the cross-interference error is within 3%. Its general accuracy is 3.35% and 3.27% in X and Y directions, and sensitivity is 0.1 mV/N, which is very suitable for measuring small cutting forces in high speed and precision machining. The smart cutting tool is portable and reliable for practical application in CNC machine tool.

Influence of body condition score on live and carcass value of cull beef cows.

Science.gov (United States)

Apple, J K

1999-10-01

Mature beef cows (n = 88) were slaughtered to determine the influence of body condition score (BCS) on carcass and live animal value. Cows were weighed and assigned a BCS (9-point scale), 24 h before slaughter. Hide and by-products weights were recorded during harvest. After a 48-h chill period, the right side of each carcass was fabricated into boneless subprimal cuts, minor cuts, lean trim, fat, and bone. Weights were recorded at all stages of fabrication. Carcass values (U.S.$/100 kg of hot carcass weight) were calculated for U.S. Utility and U.S. Cutter grades, as well as for the Utility/Cutter mix for each BCS. Gross value included the carcass value and the value of the hide and byproducts, whereas net value was calculated after harvest and fabrication costs and by-product value were considered. Live value (U.S.$/100 kg of live weight) was computed by dividing the net value by the animal's live weight 24 h before harvest. The value of the hide and by-products for BCS-2 cows was greater (Pmix, cows designated with a BCS of 7 and 8 had greater (P.05) to BCS-7 cows. Information from this study can be used by the non-fed beef industry to establish a value-based marketing system. Data from this study would indicate that marketing cull beef cows at a BCS of 6 could optimize economic returns to both cow-calf producers and non-fed beef packers.

Long range dependency and forecasting of housing price index and mortgage market rate: evidence of subprime crisis

Directory of Open Access Journals (Sweden)

Nadhem Selmi

2015-05-01

Full Text Available In this paper, we examine and forecast the House Price Index (HPI and mortgage market rate in terms of the description of the subprime crisis. We use a semi-parametric local polynomial Whittle estimator proposed by Shimotsu et al. (2005 [Shimotsu, K., & Phillips, P.C.B. (2005, Exact local Whittle estimation of fractional integration. The Annals of Statistics, 33(4, 1890-1933.] in a long memory parameter time series. Empirical investigation of HPI and mortgage market rate shows that these variables are more persistent when the d estimates are found on the Shimotsu method than on the one of Künsch (1987 [Künsch, H.R. (1987. Statistical aspects of self-similar processes. In Y. Prokhorov and V.V. Sazanov (eds., Proceedings of the First World Congress of the Bernoulli Society, VNU Science Press, Utrecht, 67-74.]. The estimating forecast values are more realistic and they strongly reflect the present US economy actuality in the two series as indicated by the forecast evaluation topics.

Annealed proton exchanged optical waveguides in lithium niobate differences between the X- and Z-cuts

CERN Document Server

Nekvindova, P; Cervena, J; Budnar, M; Razpet, A; Zorko, B; Pelicon, P; 10.1016/S0925-3467(01)00186-0

2002-01-01

Summarizes results and assessments of our systematic fabrication and characterization of proton exchanged (PE) and annealed proton exchanged (APE) waveguides in lithium niobate. This study focused on different behavior of crystallographically diverse X(1120) and Z (0001) substrate cuts during waveguide fabrication, and differences in characteristics of the resulting waveguides. Non-toxic adipic acid was used as a proton source, and the waveguides properties were defined by mode spectroscopy (waveguide characteristics) and neutron depth profiling (NDP, lithium concentration and distribution), infrared vibration spectra and elastic recoil detection analysis (ERDA, concentration and depth distribution of hydrogen). It was discovered that the X-cut structure is more permeable for moving particles (lithium and hydrogen ions), which leads to a higher effectiveness of the PE process within the X-cut. The explanation of this phenomenon is based on fitting X-cut orientation towards cleavage planes of lithium niobate c...

Development of a semiautomatic cutting machine for the fabrication of 137Cs-brachytherapy sources

International Nuclear Information System (INIS)

Avhad, B.G.; Dutta, M.L.; Saxena, S.K.; Dash, A.

2004-01-01

Cesium-137 sources are used in brachytherapy for the treatment of gynaecological cancers.The process of source preparation entails the vitrification of radioactive glass, its conversion into glass spheres, subsequent filling of spheres into platinum moulds and cutting of sources into the tubular form of dimension 1.5 mm(OD) x 5 mm(l). The large scale production of these sources demands the remote cutting operations within 4 inch thick lead shielded processing plants. This paper describes the development of a semi-automatic cutting machine, which can be used in the large scale production of 137 Cs brachytherapy sources. (author)

Development of laser repair technique for cutting impurities in secondary side of a steam generator

Energy Technology Data Exchange (ETDEWEB)

Kim, Cheol Jung; Chung, Chin Man; Kim, Min Suk; Jeong, Tae Moon

1999-12-01

In this research, the laser repair technique was investigated for the purpose of cutting impurities in secondary side of a steam generator. For this research, a high quality Nd:YAG laser was manufactured and the beam delivery experiments was performed with multimode optical fibers. Also, the small size focusing system was designed and fabricated for remote cutting and the laser cutting experiment was performed. (author)

Integrated Fabrication of a Microgripper

Institute of Scientific and Technical Information of China (English)

无

1999-01-01

Successful implementation of simple mechanism on silicon chip is a prerequisite for monolithic microrobot-ic systems. This paper describes the integrated fabrication of polycrystalline silicon microgripper. Link, fixed andactive joint, and sliding flange structures with dimensions of micrometers have been fabricated on the substrate ofmonocrystalline silicon using silicon microfabrication technology. This microgripper, which may be applied to trans-ducers or sensors, can be batch-fabricated in IC-compatible process. The movable mechanical elements are built onlayers that are later removed, so that they are free for translation and rotation. Under external driving, a microgrip-per cut from substrate would be able to catch tiny filament or small particle with dimension of 10～ 200 micrometers.

The Banking Bailout of the Subprime Crisis: Size and Effects

Directory of Open Access Journals (Sweden)

Michele Fratianni

2010-01-01

Full Text Available This paper examines government policies aimed at rescuing banks from the effects of the great financial crisis of 2007-2009. To delimit the scope of the analysis, we concentrate on the fiscal side of interventions and ignore, by design, the monetary policy reaction to the crisis. The policy response to the subprime crisis started in earnest after Lehman's failure in mid September 2008, accelerated after February 2009, and has become very large by September 2009. Governments have relied on a portfolio of intervention tools, but the biggest commitments and outlays have been in the form of debt and asset guarantees, while purchases of bad assets have been very limited. We employ event study methodology to estimate the benefits of government interventions on banks and their shareholders. Announcements directed at the banking system as a whole (general and at specific banks (specific were priced by the markets as cumulative abnormal rates of return over the selected window periods. General announcements tend to be associated with positive cumulative abnormal returns and specific announcements with negative ones. General announcements exert cross-area spillovers but are perceived by the home-country banks as subsidies boosting the competitive advantage of foreign banks. Specific announcements exert spillovers on other banks. Our results are also sensitive to the information environment. Specific announcements tend to exert a positive impact on rates of return in the pre-crisis sub-period, when announcements are few and markets have relative confidence in the "normal" information flow. The opposite takes place in the turbulent crisis sub-period when announcements are the order of the day and markets mistrust the "normal" information flow. These results appear consistent with the observed reluctance of individual institutions to come forth with requests for public assistance.

New developments in laser sintering of diamond cutting disks

NARCIS (Netherlands)

Kovalenko, V.; Golovko, L.; Meijer, J.; Anyakin, M.

2007-01-01

The analysis of techniques and problems in the fabrication of cutting tools based on super hard composites results in a solution by the application of lasers. The results of systematic study of diamond composites sintering with laser radiation are discussed. A mathematical modeling of the heat

A simple method of fabricating mask-free microfluidic devices for biological analysis.

KAUST Repository

Yi, Xin; Kodzius, Rimantas; Gong, Xiuqing; Xiao, Kang; Wen, Weijia

2010-01-01

We report a simple, low-cost, rapid, and mask-free method to fabricate two-dimensional (2D) and three-dimensional (3D) microfluidic chip for biological analysis researches. In this fabrication process, a laser system is used to cut through paper

Development of laser cutting/welding system for remote maintenance of ITER manifold

Energy Technology Data Exchange (ETDEWEB)

Yamaoka, Hiroto; Tsuchiya, Kazuyuki; Awano, Toshihiko [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan); Oka, Kiyoshi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

2002-09-01

A remote pipe cutting/welding system using a YAG laser was designed and fabricated for the maintenance of the main structural parts of ITER (International Thermonuclear Experimental Reactor), and a mock-up test carried out. The functions of this system are to cut 100A x Sch 40 pipes of SUS316L by internal access, to adjust the core gap between the as-cut pipe and new pipe, and to weld the pipes automatically. The core gap of the pipes could be decreased within the proper welding conditions by the mock-up test, and sound beads were obtained. (author)

BEHAVIOR OF THE TEN LARGEST BRAZILIAN BANKS DURING THE SUBPRIME CRISIS: AN ANALYSIS BASED ON FINANCIAL INDICATORS

Directory of Open Access Journals (Sweden)

Rosane Maria Pio da Silva

2012-06-01

Full Text Available The aim of this paper is to demonstrate the behavior of the ten largest Brazilian banks between June 2008 and September 2009, based on the analysis of financial indicators. Therefore, 16 three-monthly indices were calculated, extracted from financial statement information, which characterizes a documentary research. The indices were separated in five categories: liquidity, capital, profitability, income and market. The obtained results appointed that most financial institutions in the sample were able to manage their resources so as to gain conditions to maintain credit initially. Then, as from the first term of 2009, driven by public banks, they increased their credit operations. In addition, most banks revealed an anti-cyclical trend to encourage productive activities, preferably activities with higher liquidity levels, to the detriment of profitability, which reveals a more conservative attitude. Finally, it was verified that government initiatives, the Brazilian economic balance and the resources the banks offered helped to produce an environment to reactivate business activities during the most acute period of the subprime crisis.

Fabrication and characterization of high impact hybrid matrix composites from thermoset resin and dyneema-glass fabric reinforcement

Science.gov (United States)

Patel, R. H.; Sharma, S.; Pansuriya, T.; Malgani, E. V.; Sevkani, V.

2018-05-01

Hybrid composites have been fabricated by hand lay-up technique with epoxy resin and diethylene tri amine as a hardener for high impact energy absorption with sandwich stacking of different reinforcements of dyneema and glass fabric. High impact grade composites are nowadays gaining a lot of importance in the field of high mechanical load bearing applications, ballistics and bulletproofing. The present work emphases on the fabrication and mechanical properties of the hybrid composites of cut resistant dyneema fabric along with glass fabric reinforced in the thermosetting resin. i.e. epoxy. The prime importance while fabricating such materials have been given to the processing along with selection of the raw materials. High impact resistive materials with low density and henceforth low weight have been manufactured and characterized by IZOD impact tester, UTM, Archimedes density meter and SEM. Throughout the work, satisfactory results have been obtained. Impact resistance was observed to be boosted three times as that of the reference sample of glass fabric and epoxy. The density of the hybrid composite is observed to be 25% as that of the reference sample.

Race, Space, and Cumulative Disadvantage: A Case Study of the Subprime Lending Collapse.

Science.gov (United States)

Rugh, Jacob S; Albright, Len; Massey, Douglas S

2015-05-01

In this article, we describe how residential segregation and individual racial disparities generate racialized patterns of subprime lending and lead to financial loss among black borrowers in segregated cities. We conceptualize race as a cumulative disadvantage because of its direct and indirect effects on socioeconomic status at the individual and neighborhood levels, with consequences that reverberate across a borrower's life and between generations. Using Baltimore, Maryland as a case study setting, we combine data from reports filed under the Home Mortgage Disclosure Act with additional loan-level data from mortgage-backed securities. We find that race and neighborhood racial segregation are critical factors explaining black disadvantage across successive stages in the process of lending and foreclosure, controlling for differences in borrower credit scores, income, occupancy status, and loan-to-value ratios. We analyze the cumulative cost of predatory lending to black borrowers in terms of reduced disposable income and lost wealth. We find the cost to be substantial. Black borrowers paid an estimated additional 5 to 11 percent in monthly payments and those that completed foreclosure in the sample lost an excess of $2 million in home equity. These costs were magnified in mostly black neighborhoods and in turn heavily concentrated in communities of color. By elucidating the mechanisms that link black segregation to discrimination we demonstrate how processes of cumulative disadvantage continue to undermine black socioeconomic status in the United States today.

Bank Valuation and Its Connections with the Subprime Mortgage Crisis and Basel II Capital Accord

Directory of Open Access Journals (Sweden)

C. H. Fouche

2008-01-01

Full Text Available The ongoing subprime mortgage crisis (SMC and implementation of Basel II Capital Accord regulation have resulted in issues related to bank valuation and profitability becoming more topical. Profit is a major indicator of financial crises for households, companies, and financial institutions. An SMC-related example of this is the U.S. bank, Wachovia Corp., which reported major losses in the first quarter of 2007 and eventually was bought by Citigroup in September 2008. A first objective of this paper is to value a bank subject to Basel II based on premiums for market, credit, and operational risk. In this case, we investigate the discrete-time dynamics of banking assets, capital, and profit when loan losses and macroeconomic conditions are explicitly considered. These models enable us to formulate an optimal bank valuation problem subject to cash flow, loan demand, financing, and balance sheet constraints. The main achievement of this paper is bank value maximization via optimal choices of loan rate and supply which leads to maximal deposits, provisions for deposit withdrawals, and bank profitability. The aforementioned loan rates and capital provide connections with the SMC. Finally, OECD data confirms that loan loss provisioning and profitability are strongly correlated with the business cycle.

Irradiated multilayer film for primal meat packaging

International Nuclear Information System (INIS)

Lustig, S.; Schuetz, J.M.; Vicik, S.J.

1987-01-01

This patent deals with a heat-shrinkable, multilayer film suitable for use in fabricating bags for packaging primal and sub-primal meat cuts and processed meats. The multilayer film has a first outer layer of a first ethylene-vinyl acetate copolymer, a core layer of a polyvinylidene chloride-vinyl chloride copolymer containing between about 70 weight percent and about 90 weight percent vinylidene chloride as a barrier film, and a second outer layer of a second ethylene-vinyl acetate copolymer. The multilayer film is preferably made by co-extrusion of the layers, and then it is biaxially stretched. After biaxial stretching, the entire multilayer film is substantially uniformly irradiated to a dosage level of between about 2 megarads and about 3 megarads and heat-sealed in the form of a bag. The film is not significantly discoloured by the irradiation and the bag has improved toughness properties and heat-sealing characteristics

CO2 Laser Cutting of Hot Stamping Boron Steel Sheets

Directory of Open Access Journals (Sweden)

Pasquale Russo Spena

2017-10-01

Full Text Available This study investigates the quality of CO2 laser cutting of hot stamping boron steel sheets that are employed in the fabrication of automotive body-in-white. For this purpose, experimental laser cutting tests were conducted on 1.2 mm sheets at varying levels of laser power, cutting speed, and oxygen pressure. The resulting quality of cut edges was evaluated in terms of perpendicularity tolerance, surface irregularity, kerf width, heat affected zone, and dross extension. Experimental tests were based on a L9(34 orthogonal array design, with the effects of the process parameters on the quality responses being determined by means of a statistical analysis of variance (ANOVA. Quadratic mathematical models were developed to determine the relationships between the cutting parameters and the quality responses. Finally, a routine based on an optimization criterion was employed to predict the optimal setting of cutting factors and its effect on the quality responses. A confirmation experiment was conducted to verify the appropriateness of the optimization routine. The results show that all of the examined process parameters have a key role in determining the cut quality of hot stamping boron steel sheets, with cutting speed and their interactions having the most influencing effects. Particularly, interactions can have an opposite behavior for different levels of the process parameters.

Determination of Antimicrobial Activity of the Dyed Silk Fabrics with Some Natural Dyes

OpenAIRE

ALKAN, Rezan; TORGAN, Emine; AYDIN, Canan; KARADAG, Recep

2015-01-01

In this study, silk fabric is dyed with natural indigo. Dyed silk fabric with natural indigo was cut in the 20x20 cm2 size. Excluding a fabric, all fabrics were mordanted in the same percentage with alum metal (KAl(SO4)2.12H2O). Then, silk fabrics for green color dyeing are dyed separately with weld (Reseda luteola), gall oak (Quercus infectoria Olivier) and together weld (Reseda luteola) and gall oak (Quercus infectoria) in different percentage. Antimicrobial functionality of the twenty seve...

Um estudo sobre empresas de capital aberto brasileiras e norte-americanas do setor construção civil nos períodos ex-ant e ex-post a crise subprime

OpenAIRE

Brito, Ana Fátima de

2012-01-01

Iniciada nos Estados Unidos em 2007, a chamada Crise Subprime pode ser considerada a maior ocorrida no século até o momento, principalmente pela sua extensão, já que, pouco tempo depois da divulgação dos primeiros fatos, muitos países deram sinais de terem sido contaminados por seus efeitos. Por outro lado, outras nações como o Brasil procuravam afirmar que não seriam afetados, dados os sólidos fundamentos que sua economia apresentava. O Brasil realmente o apresentava sinais...

Laser cutting of high manganese cast steel; Komangan chuko no laser setsudan

Energy Technology Data Exchange (ETDEWEB)

Kataoka, Y.; Tokunaga, T. [University of Industrial Technology, Kanagawa (Japan); Miyazaki, T. [Chiba Institute of Technology, Chiba (Japan)

1994-08-25

This paper discusses applicability of CO2 laser to cut high manganese cast steel, and investigates the cutting conditions and characteristics. The tested material is made of steel scrap, ferro Mn and ferro Cr of 50 kg in total, which was deoxidized by using pure aluminum and injected into CO2 die by means of the ordinary casting method to make a circular rod with a diameter of 28 mm. The rod was given a heating and water toughening treatment in a muffle furnace maintaining N2 atmosphere. The base structure is an austenite system of Mn 12.4% by mass with hardness of MHV 220 to 230. The paper describes discussions on test pieces (with a thickness of 2 mm) fabricated under a laser beam frequency of 150 Hz, power outputs of 250, 350 and 500 W, and cutting speeds of 100, 300 and 500 mm/min. The cutting width increases as the laser power is increased, but is not governed by the cutting speed. Increased cutting speed roughens the surface of a cut face. The laser cutting has caused no change in hardness of the base material, and no processing deterioration has been recognized. As described, the laser cutting can be applied to finish-cutting if the cutting condition is selected properly. Simplification of the cutting process and improvement of working environment can be expected from the laser cutting. 14 refs., 12 figs., 2 tabs.

Consumo pós crise do subprime. Novos tempos na internacionalização da economia brasileira

Directory of Open Access Journals (Sweden)

Leonardo Trevisan

2011-01-01

Full Text Available A preocupação com o futuro da economia brasileira já chegou aos poetas e às revistas internacionais. Os efeitos da crise do subprime fazem parte dessa preocupação. Alguns desafios, como a internacionalização das empresas brasileiras, a atualização tecnológica da produção e as expectativas de consumo no País ganharam destaque nesse processo. A reunião do G-20, no entanto, mostrou que há diferentes métodos de lidar com a crise, preservando-se a maior influência do modo norte-americano de “fazer negócio”. A inserção brasileira na economia internacional, porém, acompanha mais o novo perfil das economias emergentes, que se desenvolve independentemente da crise. Nesse caminho, a maior dificuldade para a inserção internacional eficiente do Brasil, com manutenção da mobilidade social e da tendência de alta no consumo, continua a ser a frágil relaçãointerna entre educação e competitividade.

Target fabrication using laser and spark erosion machining

International Nuclear Information System (INIS)

Clement, X.; Coudeville, A.; Eyharts, P.; Perrine, J.P.; Rouillard, R.

1982-01-01

Fabrication of laser fusion targets requires a number of special techniques. We have developed both laser and spark erosion machining to produce minute parts of complex targets. A high repetition rate YAG laser at double frequency is used to etch various materials. For example, marks or patterns are often necessary on structured or advanced targets. The laser is also used to thin down plastic coated stalks. A spark erosion system has proved to be a versatile tool and we describe current fabrication processes like cutting, drilling, and ultra precise machining. Spark erosion has interesting features for target fabrication: it is a highly controllable and reproducible technique as well as relatively inexpensive

A study on ultra-precision machining technique for Al6061-T6 to fabricate space infrared optics

Science.gov (United States)

Ryu, Geun-man; Lee, Gil-jae; Hyun, Sang-won; Sung, Ha-yeong; Chung, Euisik; Kim, Geon-hee

2014-08-01

In this paper, analysis of variance on designed experiments with full factorial design was applied to determine the optimized machining parameters for ultra-precision fabrication of the secondary aspheric mirror, which is one of the key elements of the space cryogenic infrared optics. A single point diamond turning machine (SPDTM, Nanotech 4μpL Moore) was adopted to fabricate the material, AL6061-T6, and the three machining parameters of cutting speed, feed rate and depth of cut were selected. With several randomly assigned experimental conditions, surface roughness of each condition was measured by a non-contact optical profiler (NT2000; Vecco). As a result of analysis using Minitab, the optimum cutting condition was determined as following; cutting speed: 122 m/min, feed rate: 3 mm/min and depth of cut: 1 μm. Finally, a 120 mm diameter aspheric secondary mirror was attached to a particularly designed jig by using mixture of paraffin and wax and successfully fabricated under the optimum machining parameters. The profile of machined surface was measured by a high-accuracy 3-D profilometer(UA3P; Panasonic) and we obtained the geometrical errors of 30.6 nm(RMS) and 262.4 nm(PV), which satisfy the requirements of the space cryogenic infrared optics.

La innovación financiera, la gestion del riesgo y los flujos financieros de la economía. La crisis de los prestamos sub-prime: crónica de una muerte anunciada

OpenAIRE

Manzano Frías, Maria-Cruz

2008-01-01

La crisis que se evidenció a partir del mes de junio del 2007, y que se ha denominado crisis de los préstamos sub-prime no ha sido sino el resultado de un crecimiento excesivo del riesgo, sobre todo en el sistema financiero estadounidense, con efectos de contagio en los mercados internacionales. Este mayor riesgo no ha ido acompañado de un crecimiento de la base de capital en medida suficiente como para asegurar, en muchos casos, la solvencia de algunos intermediarios financier...

Application of YAG laser processing in underwater welding and cutting

Energy Technology Data Exchange (ETDEWEB)

Ohwaki, Katsura; Morita, Ichiro; Kojima, Toshio; Sato, Shuichi [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

2002-09-01

The high-power YAG laser is a new fabrication tool. The laser torch is easy to combine with complex with complex mechanics because of beam delivery through optical fiber. A direct underwater laser welding technology has been developed and applied to the preservation, maintenance and removal of nuclear power plants. For subdividing or removing operations for retirement of plants, the laser cutting properties were confirmed to allow a maximum cutting thickness of 80 mm. For repairing inner surface of stainless steel tanks, an underwater laser welding system using a remote-controlled robot was developed and the high quality of underwater laser welding was confirmed. (author)

Trend of laser cutting technology; Laser setsudan gijutsu no saikin no doko

Energy Technology Data Exchange (ETDEWEB)

Murai, T. [Mitsubishi Electric Corp., Tokyo (Japan)

1997-10-05

Recent trend of CO2 laser cutting is described. The cutting speed has increased five times in these seven years, and cutting is now performed at 8m/min for a hole that satisfies a circularity of 50{mu}m. In the low-speed domain, again, cutting accuracy is as high as 20{mu}m. In the cutting of thick plates, laser encounters some difficulties, which include the increased thermal load on optical parts and devices in the oscillator, lessened cutting condition tolerance, variation in the accuracy of products, difficult cutting, etc. Discussed in this report are measures for correcting factors affecting product quality with reference taken to a thick soft steel plate. A laser beam emitted by an oscillator is condensed by and projected through a condenser lens, and the condensing capability is affected by various factors, such as the beam mode order, beam diameter, and focal length, etc. What is important is to find out the optimal conditions. The assist gas has to satisfy certain conditions because it assumes an important role in controlling the discharge of molten metal from cut grooves, heat generated by oxidation reaction, and cooling. The properties of the material to be cut also exert some influence. In the case of thick plate cutting, the cutting capability is governed by the geometry to be fabricated. Also employed for the prevention of poor jobs due to improper condition switchover and cutting routes is an optimal cutting condition control technique. 3 refs., 12 figs.

Chemical scissors cut phosphorene nanostructures

International Nuclear Information System (INIS)

Peng, Xihong; Wei, Qun

2014-01-01

Phosphorene, a recently fabricated two-dimensional puckered honeycomb structure of phosphorus, showed promising properties for applications in nano-electronics. In this work, we report a chemical scissors effect on phosphorene, using first-principles method. It was found that chemical species, such as H, OH, F, and Cl, can act as scissors to cut phosphorene. Phosphorus nanochains and nanoribbons can be obtained. The scissors effect results from the strong bonding between the chemical species and phosphorus atoms. Other species such as O, S and Se fail to cut phosphorene nanostructures due to their weak bonding with phosphorus. The electronic structures of the produced P-chains reveal that the hydrogenated chain is an insulator while the pristine chain is a one-dimensional Dirac material, in which the charge carriers are massless fermions travelling at an effective speed of light ∼8 × 10 5 m s −1 . The obtained zigzag phosphorene nanoribbons show either metallic or semiconducting behaviors, depending on the treatment of the edge phosphorus atoms. (paper)

Financial Performance of Islamic and Conventional Banks During and After US Sub-prime Crisis in Pakistan: A Comparative Study

Directory of Open Access Journals (Sweden)

Muhammad Bilal

2015-12-01

Full Text Available Islamic banking system that is based on Shariah principles is considered more resilient to the financial shocks due to its interest free nature. This study is aimed to compare the financial performances and investigate whether Islamic banks are more profitable, liquid, less risky and operationally efficient compared to conventional banks during and after US Sub-prime crisis in Pakistan. The time span used for the study was from 2007 to 2012. Thirteen financial ratios composed of five Islamic and five conventional banks to measure the financial performance in terms of profitability, risk and solvency, liquidity and capital adequacy. Independent sample t-test is used to determine the significance of mean differences of selected ratios. The results of profitability measures indicate that Islamic banks remained less profitable; however, liquidity performances of Islamic banks were better than conventional banks. However, overall operational efficiency measures are not in favour of Islamic banks. The study concluded that conventional banks performed more efficiently and profitably as compared to Islamic banks. The opportunity of future empirical study is recommended at the end of this paper.

Plasma arc cutting: speed and cut quality

International Nuclear Information System (INIS)

Nemchinsky, V A; Severance, W S

2009-01-01

When cutting metal with plasma arc cutting, the walls of the cut are narrower at the bottom than at the top. This lack of squareness increases as the cutting speed increases. A model of this phenomenon, affecting cut quality, is suggested. A thin liquid layer, which separates the plasma from the solid metal to be melted, plays a key role in the suggested model. This layer decreases heat transfer from the plasma to the solid metal; the decrease is more pronounced the higher the speed and the thicker the liquid metal layer. Since the layer is thicker at the bottom of the cut, the heat transfer effectiveness is lower at the bottom. The decrease in heat transfer effectiveness is compensated by the narrowness of the cut. The suggested model allows one to calculate the profile of the cut. The result of the calculations of the cutting speeds for plates of various thicknesses, at which the squareness of the cut is acceptable, agrees well with the speeds recommended by manufacturers. The second effect considered in the paper is the deflection of the plasma jet from the vertical at a high cutting speed. A qualitative explanation of this phenomenon is given. We believe the considerations of this paper are pertinent to other types of cutting with moving heat sources.

Cutting

Science.gov (United States)

... Staying Safe Videos for Educators Search English Español Cutting KidsHealth / For Teens / Cutting What's in this article? ... Getting Help Print en español Cortarse What Is Cutting? Emma's mom first noticed the cuts when Emma ...

Ultrafast Optical Modulation of Second- and Third-Harmonic Generation from Cut-Disk-Based Metasurfaces

KAUST Repository

Sartorello, Giovanni; Olivier, Nicolas; Zhang, Jingjing; Yue, Weisheng; Gosztola, David J.; Wiederrecht, Gary P.; Wurtz, Gré gory; Zayats, Anatoly V.

2016-01-01

We design and fabricate a metasurface composed of gold cut-disk resonators that exhibits a strong coherent nonlinear response. We experimentally demonstrate all-optical modulation of both second- and third-harmonic signals on a subpicosecond time

Fabrication of ten-fold photonic quasicrystalline structures

Directory of Open Access Journals (Sweden)

XiaoHong Sun

2015-05-01

Full Text Available Compared to periodic crystals, quasicrystals have higher point group symmetry and are more favorable in achieving complete band-gaps. In this report, a top-cut prism interferometer is designed to fabricate ten-fold photonic quasicrystalline structures. By optimizing the exposing conditions and material characteristics, appropriate quasicrystals have been obtained in the SU8 photoresist films. Atomic Force Microscopy and laser diffraction are used to characterize the fabricated structures. The measurement results show the consistence between the theoretical design and experiments. This will provide guidance for the large-area and fast production of ten-fold quasicrystalline structures with high quality.

A simple method of fabricating mask-free microfluidic devices for biological analysis.

KAUST Repository

Yi, Xin

2010-09-07

We report a simple, low-cost, rapid, and mask-free method to fabricate two-dimensional (2D) and three-dimensional (3D) microfluidic chip for biological analysis researches. In this fabrication process, a laser system is used to cut through paper to form intricate patterns and differently configured channels for specific purposes. Bonded with cyanoacrylate-based resin, the prepared paper sheet is sandwiched between glass slides (hydrophilic) or polymer-based plates (hydrophobic) to obtain a multilayer structure. In order to examine the chip\\'s biocompatibility and applicability, protein concentration was measured while DNA capillary electrophoresis was carried out, and both of them show positive results. With the utilization of direct laser cutting and one-step gas-sacrificing techniques, the whole fabrication processes for complicated 2D and 3D microfluidic devices are shorten into several minutes which make it a good alternative of poly(dimethylsiloxane) microfluidic chips used in biological analysis researches.

Inexpensive, rapid prototyping of microfluidic devices using overhead transparencies and a laser print, cut and laminate fabrication method.

Science.gov (United States)

Thompson, Brandon L; Ouyang, Yiwen; Duarte, Gabriela R M; Carrilho, Emanuel; Krauss, Shannon T; Landers, James P

2015-06-01

We describe a technique for fabricating microfluidic devices with complex multilayer architectures using a laser printer, a CO2 laser cutter, an office laminator and common overhead transparencies as a printable substrate via a laser print, cut and laminate (PCL) methodology. The printer toner serves three functions: (i) it defines the microfluidic architecture, which is printed on the overhead transparencies; (ii) it acts as the adhesive agent for the bonding of multiple transparency layers; and (iii) it provides, in its unmodified state, printable, hydrophobic 'valves' for fluidic flow control. By using common graphics software, e.g., CorelDRAW or AutoCAD, the protocol produces microfluidic devices with a design-to-device time of ∼40 min. Devices of any shape can be generated for an array of multistep assays, with colorimetric detection of molecular species ranging from small molecules to proteins. Channels with varying depths can be formed using multiple transparency layers in which a CO2 laser is used to remove the polyester from the channel sections of the internal layers. The simplicity of the protocol, availability of the equipment and substrate and cost-effective nature of the process make microfluidic devices available to those who might benefit most from expedited, microscale chemistry.

Structural damage in thin SLIM-Cut c-Si foils fabricated for solar cell purposes: atomic assessment by electron spin resonance

International Nuclear Information System (INIS)

Kepa, J; Stesmans, A; Martini, R

2015-01-01

Within the context of reducing production costs, thin (<90 μm) silicon foils intended for photovoltaic applications have been fabricated from standard (100)Si wafers using a low-temperature (<150 °C) stress-induced lift-off process. A multi-frequency electron spin resonance (ESR) study was performed in order to evaluate, at atomic scale, the quality of the material in terms of defects, including identification and quantification. Generally, a complex ESR spectrum is observed, disentangled as the superposition of three separate signals. This includes, most prominently (∼91% of total density) the D-line (Si 3  ≡ Si· dangling bonds in a disordered Si environment), a set (∼6%) of highly anisotropic signals ascribed to dislocations (K1-like), and a triplet, identified as the Si-SL5 N-donor defect. Defect density depth profiling from the lift-off side shows all signals disappear in tandem after etching off a ∼33 μm thick Si layer, indicating a highly correlated−equal in relative terms−distribution of the three types of defects over the affected top part of the Si foil. The defect density is found to be highly non-uniform laterally, with the density peaking near the crack initiation point, from which defect generation spreads. It is thus found that the SLIM-Cut method for fabrication of thin Si foils results in the introduction of defects that would unacceptably impair the functionality of photovoltaic cells built on these substrates. Fortunately, this may be cured by etching off a thin top Si layer, resulting in a most useful thin Si foil of standard high quality. (paper)

A Study on The Development of Local Exhaust Ventilation System (LEV’s) for Installation of Laser Cutting Machine

Science.gov (United States)

Harun, S. I.; Idris, S. R. A.; Tamar Jaya, N.

2017-09-01

Local exhaust ventilation (LEV) is an engineering system frequently used in the workplace to protect operators from hazardous substances. The objective of this project is design and fabricate the ventilation system as installation for chamber room of laser cutting machine and to stimulate the air flow inside chamber room of laser cutting machine with the ventilation system that designed. LEV’s fabricated with rated voltage D.C 10.8V and 1.5 ampere. Its capacity 600 ml, continuously use limit approximately 12-15 minute, overall length LEV’s fabricated is 966 mm with net weight 0.88 kg and maximum airflow is 1.3 meter cubic per minute. Stimulate the air flow inside chamber room of laser cutting machine with the ventilation system that designed and fabricated overall result get 2 main gas vapor which air and carbon dioxide. For air gas which experimented by using anemometer, general duct velocity that produce is same with other gas produce, carbon dioxide which 5 m/s until 10 m/s. Overall result for 5 m/s and 10 m/s as minimum and maximum duct velocity produce for both air and carbon dioxide. The air gas flow velocity that captured by LEV’s fabricated, 3.998 m/s average velocity captured from 5 m/s duct velocity which it efficiency of 79.960% and 7.667 m/s average velocity captured from 10 m/s duct velocity with efficiency of 76.665%. For carbon dioxide gas flow velocity that captured by LEV’s fabricated, 3.674 m/s average velocity captured from 5 m/s duct velocity which it efficiency of 73.480% and 8.255 m/s average velocity captured from 10 m/s duct velocity with efficiency of 82.545%.

Fabrication on a ZnO/ST-cut quartz based love wave viscosity sensor

Energy Technology Data Exchange (ETDEWEB)

Wu, Tsung Tsong; Huang, Zhi Da; Chen, Yung Yu; Liu, Pei Ling [Institute of Applied Mechanics, National Taiwan University, Taipai (China)

2006-05-15

In this paper, we aim to propose a rugged and relatively inexpensive acoustic wave viscometer that is easy to use and to fabricate by the conventional semiconductor manufacturing processes. First, we fabricated five different Love wave acoustic devices based on ZnO/90 degree rotated ST-quartz layered structure and incorporated with Polydimethylsiloxane (PMDS) flow cell. This allows a tiny controlled amount of analyte to be confined solely upon the sensing area between the IDTs of our Love wave sensor, preventing unwanted electric interactions with IDTs. The PDMS liquid flow cell is fabricated by replica molding. Using a simple set of fixture, the flow cell can be clamped onto our Love wave sensor and a constant volume of analyte can be confined on the sensing surface. Finally, five glycerites with different viscosities were prepared for viscosity measurement. The measured results show that the frequency shifts are in good correlation with the known viscosities. We note that results of this study can further be implemented as an easy to use and inexpensive acoustic viscometer.

Fabrication od a ZnO/ST-cut quartz based love wave viscosity sensor

Energy Technology Data Exchange (ETDEWEB)

Wu, Tsung Tsong; Huang, Zhi Da; Chen, Yung Yu; Liu, Pei Ling [Institute of Applied Mechanics, National Taiwan University, Taipai (China)

2006-05-15

In this paper, we aim to propose a rugged and relatively inexpensive acoustic wave viscometer that is easy to use and to fabricate by the conventional semiconductor manufacturing processes. First, we fabricated five different Love wave acoustic devices based on ZnO/90 degree rotated ST-quartz layered structure and incorporated with Polydimethylsiloxane (PMDS) flow cell. This allows a tiny controlled amount of analyte to be confined solely upon the sensing area between the IDTs of our Love wave sensor, preventing unwanted electric interactions with IDTs. The PDMS liquid flow cell is fabricated by replica molding. Using a simple set of fixture, the flow cell can be clamped onto our Love wave sensor and a constant volume of analyte can be confined on the sensing surface. Finally, five glycerites with different viscosities were prepared for viscosity measurement. The measured results show that the frequency shifts are in good correlation with the known viscosities. We note that results of this study can further be implemented as an easy to use and inexpensive acoustic viscometer.

Fabrication od a ZnO/ST-cut quartz based love wave viscosity sensor

International Nuclear Information System (INIS)

Wu, Tsung Tsong; Huang, Zhi Da; Chen, Yung Yu; Liu, Pei Ling

2006-01-01

In this paper, we aim to propose a rugged and relatively inexpensive acoustic wave viscometer that is easy to use and to fabricate by the conventional semiconductor manufacturing processes. First, we fabricated five different Love wave acoustic devices based on ZnO/90 degree rotated ST-quartz layered structure and incorporated with Polydimethylsiloxane (PMDS) flow cell. This allows a tiny controlled amount of analyte to be confined solely upon the sensing area between the IDTs of our Love wave sensor, preventing unwanted electric interactions with IDTs. The PDMS liquid flow cell is fabricated by replica molding. Using a simple set of fixture, the flow cell can be clamped onto our Love wave sensor and a constant volume of analyte can be confined on the sensing surface. Finally, five glycerites with different viscosities were prepared for viscosity measurement. The measured results show that the frequency shifts are in good correlation with the known viscosities. We note that results of this study can further be implemented as an easy to use and inexpensive acoustic viscometer.

Fabrication on a ZnO/ST-cut quartz based love wave viscosity sensor

International Nuclear Information System (INIS)

Wu, Tsung Tsong; Huang, Zhi Da; Chen, Yung Yu; Liu, Pei Ling

2006-01-01

In this paper, we aim to propose a rugged and relatively inexpensive acoustic wave viscometer that is easy to use and to fabricate by the conventional semiconductor manufacturing processes. First, we fabricated five different Love wave acoustic devices based on ZnO/90 degree rotated ST-quartz layered structure and incorporated with Polydimethylsiloxane (PMDS) flow cell. This allows a tiny controlled amount of analyte to be confined solely upon the sensing area between the IDTs of our Love wave sensor, preventing unwanted electric interactions with IDTs. The PDMS liquid flow cell is fabricated by replica molding. Using a simple set of fixture, the flow cell can be clamped onto our Love wave sensor and a constant volume of analyte can be confined on the sensing surface. Finally, five glycerites with different viscosities were prepared for viscosity measurement. The measured results show that the frequency shifts are in good correlation with the known viscosities. We note that results of this study can further be implemented as an easy to use and inexpensive acoustic viscometer.

Determination of cut front position in laser cutting

Science.gov (United States)

Pereira, M.; Thombansen, U.

2016-07-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable.

Development of real-time monitoring and control in COIL laser cutting for joint R and D between Korea and U.S

Energy Technology Data Exchange (ETDEWEB)

Chung, Chin Man; Kim, Cheol Jung; Kim, Min Suk; Baik, Sung Hoon; Kwon, Sung Ok; Park, Sun Kyu

2000-12-01

The laser monitoring and control technique investigated to experiment for cutting kerf width and result of laser cutting for D and D of nuclear facility. The demands for this laser monitoring and control technique were applied to process control in laser cutting and to fabricate monitoring and control system, focusing lens assembly. This system can had a advantage to monitor and control the laser cutting on real time. KAERI investigated the COIL laser and monitored 2 kW laser power.

Development of real-time monitoring and control in COIL laser cutting for joint R and D between Korea and U.S

International Nuclear Information System (INIS)

Chung, Chin Man; Kim, Cheol Jung; Kim, Min Suk; Baik, Sung Hoon; Kwon, Sung Ok; Park, Sun Kyu

2000-12-01

The laser monitoring and control technique investigated to experiment for cutting kerf width and result of laser cutting for D and D of nuclear facility. The demands for this laser monitoring and control technique were applied to process control in laser cutting and to fabricate monitoring and control system, focusing lens assembly. This system can had a advantage to monitor and control the laser cutting on real time. KAERI investigated the COIL laser and monitored 2 kW laser power

INSURANCE OF KNITTED PRODUCTS QUALITY THROUGH THE ANALYSIS AND EVALUATION OF NON-QUALITY DURING THE OPERATIONS IN THE CUTTING ROOM

Directory of Open Access Journals (Sweden)

LUTIC Liliana

2014-05-01

Full Text Available n a knitting- confection profile factory, any activity oriented toward evaluation, maintenance or improvement of products quality level is based on measuring and examining the product quality characteristics, in order to establish conformity to the quality specifications and/or naming the non-quality characteristics (establishing defects and fabrication deficiencies. We can consider non-quality as complementary to quality, although a definitive distinction cannot always be made between the two categories or states. Cutting holds a key role in insuring shape precision and pieces dimensions, determining the quality of the confection process, its structure and manual stages frequency. The quality of the cutting operation, appreciated through the precision and aspect of cut contours, existence and precision of markings, is directly reflected in the finite product’s quality, which entails knowledge of cutting instrument - fabric interactions. In compliance of the technological regime during the operations in the cutting room can determine: incorrect marking, spreading, sectioning or cutting. Non-quality of intermediate products obtained in the cutting department can be evaluated and controlled through defectologic control methods.The De – Ca – Re method (defect-cause-remedy correlation, applied in this paper, allows establishing the most important causes that generate defects, as well as preventive and corrective actions to eliminate these causes. This paper systematically presents the main defects that may occur during operations in the cutting room, causes that generate these defects, along with their preventive and corrective actions.

Experimental testing of exchangeable cutting inserts cutting ability

OpenAIRE

Čep, Robert; Janásek, Adam; Čepová, Lenka; Petrů, Jana; Hlavatý, Ivo; Car, Zlatan; Hatala, Michal

2013-01-01

The article deals with experimental testing of the cutting ability of exchangeable cutting inserts. Eleven types of exchangeable cutting inserts from five different manufacturers were tested. The tested cutting inserts were of the same shape and were different especially in material and coating types. The main aim was both to select a suitable test for determination of the cutting ability of exchangeable cutting inserts and to design such testing procedure that could make it possible...

Determination of cut front position in laser cutting

International Nuclear Information System (INIS)

Pereira, M; Thombansen, U

2016-01-01

Laser cutting has a huge importance to manufacturing industry. Laser cutting machines operate with fixed technological parameters and this does not guarantee the best productivity. The adjustment of the cutting parameters during operation can improve the machine performance. Based on a coaxial measuring device it is possible to identify the cut front position during the cutting process. This paper describes the data analysis approach used to determine the cut front position for different feed rates. The cut front position was determined with good resolution, but improvements are needed to make the whole process more stable. (paper)

Characterization of vibratory turning in cutting zone using a pneumatic quick-stop device

Directory of Open Access Journals (Sweden)

Saeid Amini

2017-04-01

Full Text Available Shear angle and sticking length are two crucial parameters in mechanics of metal cutting. These two parameters directly influence machinability factors such as cutting forces. Thus, shear angle and sticking length were investigated in vibratory turning process by using a pneumatic quick-stop device which was designed and fabricated, in this study. After preparation of ultrasonic assisted turning set-up, experimental tests have been carried out on two types of steel: AISI-1060 and AISI 304. Accordingly, the process of chip formation in each particular cutting test was quickly stopped when deformed chip was still in contact with workpiece. As a result, it was revealed that added linear vibration leads the turning operation to be improved by increase of shear angle and decrease of sticking length. Moreover, the effect of ultrasonic vibration on cutting force and chip micro-hardness is evaluated.

Core Cutting Test with Vertical Rock Cutting Rig (VRCR)

Science.gov (United States)

Yasar, Serdar; Osman Yilmaz, Ali

2017-12-01

Roadheaders are frequently used machines in mining and tunnelling, and performance prediction of roadheaders is important for project economics and stability. Several methods were proposed so far for this purpose and, rock cutting tests are the best choice. Rock cutting tests are generally divided into two groups which are namely, full scale rock cutting tests and small scale rock cutting tests. These two tests have some superiorities and deficiencies over themselves. However, in many cases, where rock sampling becomes problematic, small scale rock cutting test (core cutting test) is preferred for performance prediction, since small block samples and core samples can be conducted to rock cutting testing. Common problem for rock cutting tests are that they can be found in very limited research centres. In this study, a new mobile rock cutting testing equipment, vertical rock cutting rig (VRCR) was introduced. Standard testing procedure was conducted on seven rock samples which were the part of a former study on cutting rocks with another small scale rock cutting test. Results showed that core cutting test can be realized successfully with VRCR with the validation of paired samples t-test.

Improved cutting performance in high power laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

2003-01-01

Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described.......Recent results in high power laser cutting especially with focus on cutting of mild grade steel types for shipbuilding are described....

Fabrication and characteristics of cube-post microreactors for methanol steam reforming

International Nuclear Information System (INIS)

Zeng, Dehuai; Pan, Minqiang; Wang, Liming; Tang, Yong

2012-01-01

Highlights: ► We developed a cube-post microreactor for methanol steam reforming. ► We investigated the influences of micro-milling parameters on the burr formation during fabricating the cube posts. ► Larger cutting speed, smaller feed rate and cutting depth are in favor of obtaining relatively small burrs. ► Cube post and manifold structure show important effects on reaction performances at relatively low reaction temperature. -- Abstract: The lamination-plate structure patterned with microchannels and triangle manifolds regarded as one of the preferred constructions for micro fuel reformers. Learned from the microchannel plate structure, a similar plate structure with cube-post array and triangle manifolds is proposed in this work. A micro-milling process is applied to fabricate the cube posts on the plate surface, and the influences of cutting parameters on the burr formation are analyzed. Experimental results indicate that larger cutting speed, smaller feed rate and cutting depth are in favor of obtaining relatively small burrs. Two plates with different cube-post dimensions and manifold structures are experimentally investigated the performances of methanol steam reforming over the Cu/Zn/Al/Zr catalyst. It indicates that the reactor with small-scale cube posts and acute triangle manifold presents better reforming performances at 260 °C than that of the one with large-scale cube posts and right triangle manifolds. However, their performances are closed to each other at relatively high reaction temperature since the catalyst activity is situated in dominated position at the time.

Twice cutting method reduces tibial cutting error in unicompartmental knee arthroplasty.

Science.gov (United States)

Inui, Hiroshi; Taketomi, Shuji; Yamagami, Ryota; Sanada, Takaki; Tanaka, Sakae

2016-01-01

Bone cutting error can be one of the causes of malalignment in unicompartmental knee arthroplasty (UKA). The amount of cutting error in total knee arthroplasty has been reported. However, none have investigated cutting error in UKA. The purpose of this study was to reveal the amount of cutting error in UKA when open cutting guide was used and clarify whether cutting the tibia horizontally twice using the same cutting guide reduced the cutting errors in UKA. We measured the alignment of the tibial cutting guides, the first-cut cutting surfaces and the second cut cutting surfaces using the navigation system in 50 UKAs. Cutting error was defined as the angular difference between the cutting guide and cutting surface. The mean absolute first-cut cutting error was 1.9° (1.1° varus) in the coronal plane and 1.1° (0.6° anterior slope) in the sagittal plane, whereas the mean absolute second-cut cutting error was 1.1° (0.6° varus) in the coronal plane and 1.1° (0.4° anterior slope) in the sagittal plane. Cutting the tibia horizontally twice reduced the cutting errors in the coronal plane significantly (Pcutting the tibia horizontally twice using the same cutting guide reduced cutting error in the coronal plane. Copyright © 2014 Elsevier B.V. All rights reserved.

Design and fabrication of advanced hybrid circuits for high energy physics

International Nuclear Information System (INIS)

Haller, G.M.; Moss, J.; Freytag, D.R.; Nelson, D.; Yim, A.; Lo, C.C.

1987-10-01

Current design and fabrication techniques of hybrid devices are explained for the Drift Chamber and the Liquid Argon Calorimeter for the Stanford Linear Collider Large Detector (SLD) at SLAC. Methods of developing layouts, ranging from hand-cut templates to advanced designs utilizing CAD tools with special hybrid design software were applied. Physical and electrical design rules for good yield and performance are discussed. Fabrication and assembly of the SLD hybrids are described. 7 refs., 10 figs

Periodic domain inversion in x-cut single-crystal lithium niobate thin film

Energy Technology Data Exchange (ETDEWEB)

Mackwitz, P., E-mail: peterm@mail.upb.de; Rüsing, M.; Berth, G.; Zrenner, A. [Department Physik, Universität Paderborn, 33095 Paderborn (Germany); Center for Optoelectronics and Photonics Paderborn, 33095 Paderborn (Germany); Widhalm, A.; Müller, K. [Department Physik, Universität Paderborn, 33095 Paderborn (Germany)

2016-04-11

We report the fabrication of periodically poled domain patterns in x-cut lithium niobate thin-film. Here, thin films on insulator have drawn particular attention due to their intrinsic waveguiding properties offering high mode confinement and smaller devices compared to in-diffused waveguides in bulk material. In contrast to z-cut thin film lithium niobate, the x-cut geometry does not require back electrodes for poling. Further, the x-cut geometry grants direct access to the largest nonlinear and electro-optical tensor element, which overall promises smaller devices. The domain inversion was realized via electric field poling utilizing deposited aluminum top electrodes on a stack of LN thin film/SiO{sub 2} layer/Bulk LN, which were patterned by optical lithography. The periodic domain inversion was verified by non-invasive confocal second harmonic microscopy. Our results show domain patterns in accordance to the electrode mask layout. The second harmonic signatures can be interpreted in terms of spatially, overlapping domain filaments which start their growth on the +z side.

Miraculous financial engineering or toxic finance? The genesis of the U.S. subprime mortgage loans crisis and its consequences on the global financial markets and real economy

Directory of Open Access Journals (Sweden)

Ivo Pezzuto

2012-09-01

around the world, transferring to these investors the rights to the mortgage payments and the related credit risk. With the collapse of the first banks and hedge funds in 2007 the rising number of foreclosures helped speed the fall of housing prices, and the number of prime mortgages in default began to increase. As many CDO products were held on a “mark to market” basis, the paralysis in the credit markets and the collapse of liquidity in these products let to the dramatic write-downs in 2007. When stock markets in the United States, Europe and Asia continued to plunge, leading central banks took the drastic step of a coordinated cut in interest rates and Governments coordinated actions that included taking equity stakes in major banks. This paper written by the Author (on October 7th, 2008 at the rise of these dramatic events, aims to demonstrate, through solid and fact-based assumptions, that this dramatic global financial crisis could have been addressed and managed earlier and better by many of the stakeholders involved in the subprime mortgage lending process such as, banks’ and investment funds management, rating agencies, banking and financial markets supervisory authorities. It also unfortunately demonstrates the corporate social responsibility failure and the moral hazard of many key players involved in this crisis, since a lot of them probably knew quite well what was happening but have preferred not to do anything or to do little and late in order to change the dramatic course of the events.

Axial and transverse tensile properties Zr-2.5Nb pressure tube off-cuts

International Nuclear Information System (INIS)

Shah, Priti K.; Dubey, J.S.; Shriwastaw, R.S.; Balakrishnan, K.S.; Anantharaman, S.; Chakravartty, J.K.

2011-01-01

Zr-2.5Nb alloys in cold worked and stress relieved (CWSR) condition serves as pressure boundary for hot coolant in Indian Pressurized Heavy Water Reactor (IPHWR). Due to both microstructural and crystallographic anisotropy, the mechanical properties in general and fracture behavior in particular are anisotropic for this material. To understand the anisotropic mechanical behavior of the Zr-2.5Nb pressure tubes of IPHWRs, tension tests were carried out on the RAPS-2 and KAPS-2 pressure tube off-cuts. Off-cuts are the small pieces cut from the two ends of a pressure tube before installing it into the PHWR. Miniature flat tensile specimens (without applying any flattening treatment to the pressure tube) of both longitudinal (or axial) and transverse orientation were fabricated from the off-cuts. Tension tests were carried out both at room temperature and 300 deg C. The transverse specimens showed higher strength and lower elongation than that of the axial ones. The back-end off-cuts showed higher strength compared to front-end off-cuts along axial direction whereas the same is not true for transverse direction specimens. One typical plot obtained in the testing of one of the off-cut is shown. The paper will discuss about the importance of the work carried out, test specimens, test method and results obtained in detail

Fibre laser cutting stainless steel: Fluid dynamics and cut front morphology

Science.gov (United States)

Pocorni, Jetro; Powell, John; Deichsel, Eckard; Frostevarg, Jan; Kaplan, Alexander F. H.

2017-01-01

In this paper the morphology of the laser cut front generated by fibre lasers was investigated by observation of the 'frozen' cut front, additionally high speed imaging (HSI) was employed to study the fluid dynamics on the cut front while cutting. During laser cutting the morphology and flow properties of the melt film on the cut front affect cut quality parameters such as cut edge roughness and dross (residual melt attached to the bottom of the cut edge). HSI observation of melt flow down a laser cutting front using standard cutting parameters is experimentally problematic because the cut front is narrow and surrounded by the kerf walls. To compensate for this, artificial parameters are usually chosen to obtain wide cut fronts which are unrepresentative of the actual industrial process. This paper presents a new experimental cutting geometry which permits HSI of the laser cut front using standard, commercial parameters. These results suggest that the cut front produced when cutting medium section (10 mm thick) stainless steel with a fibre laser and a nitrogen assist gas is covered in humps which themselves are covered by a thin layer of liquid. HSI observation and theoretical analysis reveal that under these conditions the humps move down the cut front at an average speed of approximately 0.4 m/s while the covering liquid flows at an average speed of approximately 1.1 m/s, with an average melt depth at the bottom of the cut zone of approximately 0.17 mm.

Fabrication of polystyrene microfluidic devices using a pulsed CO2 laser system

KAUST Repository

Li, Huawei

2013-10-10

In this article, we described a simple and rapid method for fabrication of droplet microfluidic devices on polystyrene substrate using a CO2 laser system. The effects of the laser power and the cutting speed on the depth, width and aspect ratio of the microchannels fabricated on polystyrene were investigated. The polystyrene microfluidic channels were encapsulated using a hot press bonding technique. The experimental results showed that both discrete droplets and laminar flows could be obtained in the device.

Fabrication of polystyrene microfluidic devices using a pulsed CO2 laser system

KAUST Repository

Li, Huawei; Fan, Yiqiang; Foulds, Ian G.; Kodzius, Rimantas

2013-01-01

In this article, we described a simple and rapid method for fabrication of droplet microfluidic devices on polystyrene substrate using a CO2 laser system. The effects of the laser power and the cutting speed on the depth, width and aspect ratio of the microchannels fabricated on polystyrene were investigated. The polystyrene microfluidic channels were encapsulated using a hot press bonding technique. The experimental results showed that both discrete droplets and laminar flows could be obtained in the device.

Decrease of FIB-induced lateral damage for diamond tool used in nano cutting

Energy Technology Data Exchange (ETDEWEB)

Wu, Wei [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Xu, Zongwei, E-mail: zongweixu@163.com [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Fang, Fengzhou, E-mail: fzfang@gmail.com [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Liu, Bing; Xiao, Yinjing; Chen, Jinping [State Key Laboratory of Precision Measuring Technology and Instruments, Centre of MicroNano Manufacturing Technology, Tianjin University, Tianjin 300072 (China); Wang, Xibin [School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081 (China); Liu, Hongzhong [State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an 710049 (China)

2014-07-01

Highlights: • We mainly aim to characterize and decrease the FIB-induced damage on diamond tool. • Raman and XPS methods were used to characterize the nanoscale FIB-induced damage. • Lower energy FIB can effectively lessen the FIB-induced damage on diamond tool. • The diamond tools’ performance was greatly improved after FIB process optimization. • 6 nm chip thickness of copper was achieved by diamond tool with 22 nm edge radius. - Abstract: Diamond cutting tools with nanometric edge radius used in ultra-precision machining can be fabricated by focused ion beam (FIB) technology. However, due to the nanoscale effects, the diamond tools performance and the cutting edge lifetime in nano cutting would be degraded because of the FIB-induced nanoscale lateral damage. In this study, the methods of how to effectively characterize and decrease the FIB-induced lateral damage for diamond tool are intensively studied. Based on the performance optimization diamond machining tools, the controllable chip thickness of less than 10 nm was achieved on a single-crystal copper in nano cutting. In addition, the ratio of minimum thickness of chip (MTC) to tool edge radius of around 0.3–0.4 in nano cutting is achieved. Methods for decreasing the FIB-induced damage on diamond tools and adding coolant during the nano cutting are very beneficial in improving the research of nano cutting and MTC. The nano cutting experiments based on the sharp and high performance of diamond tools would validate the nano cutting mechanisms that many molecular dynamic simulation studies have put forward and provide new findings for nano cutting.

A Cut-and-Paste Approach to 3D Graphene-Oxide-Based Architectures.

Science.gov (United States)

Luo, Chong; Yeh, Che-Ning; Baltazar, Jesus M Lopez; Tsai, Chao-Lin; Huang, Jiaxing

2018-04-01

Properly cut sheets can be converted into complex 3D structures by three basic operations including folding, bending, and pasting to render new functions. Folding and bending are extensively employed in crumpling, origami, and pop-up fabrications for 3D structures. Pasting joins different parts of a material together, and can create new geometries that are fundamentally unattainable by folding and bending. However, it has been much less explored, likely due to limited choice of weldable thin film materials and residue-free glues. Here it is shown that graphene oxide (GO) paper is one such suitable material. Stacked GO sheets can be readily loosened up and even redispersed in water, which upon drying, restack to form solid structures. Therefore, water can be utilized to heal local damage, glue separated pieces, and release internal stress in bent GO papers to fix their shapes. Complex and dynamic 3D GO architectures can thus be fabricated by a cut-and-paste approach, which is also applicable to GO-based hybrid with carbon nanotubes or clay sheets. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Cutting state identification

International Nuclear Information System (INIS)

Berger, B.S.; Minis, I.; Rokni, M.

1997-01-01

Cutting states associated with the orthogonal cutting of stiff cylinders are identified through an analysis of the singular values of a Toeplitz matrix of third order cumulants of acceleration measurements. The ratio of the two pairs of largest singular values is shown to differentiate between light cutting, medium cutting, pre-chatter and chatter states. Sequences of cutting experiments were performed in which either depth of cut or turning frequency was varied. Two sequences of experiments with variable turning frequency and five with variable depth of cut, 42 cutting experiments in all, provided a database for the calculation of third order cumulants. Ratios of singular values of cumulant matrices find application in the analysis of control of orthogonal cutting

Precision cutting and drilling with the Nd-YAG laser

International Nuclear Information System (INIS)

Lingenfelter, A.C.; Anglin, C.D.; Westrich, C.N.; Murchie, J.R.

1986-01-01

The Laser Processing Facility of the Materials Fabrication Division of Lawrence Livermore National Laboratory has two pulsed Nd-YAG lasers mounted on machine tool bases. Over the years the authors have had requirements for cutting a wide variety of materials, frequently to very tight dimensional tolerances. They have found that the laser process is particularly well suited for two application areas; (1) for thin cross sections of most all materials, and (2) for refractory metals and ceramics such as tungsten, tantalum, and molybdenum, silicon wafers, alumina, and graphite foil. Some of these materials are difficult if not impossible to cut and drill in any other manner. Examples of each of these types of applications are sighted. Data are presented to illustrate the effects and interactions of laser parameter variables such as aperturing, choice of lenses, focus, pulse length, and energy level. Examples of applications are shown

HgI2 detector fabrication

International Nuclear Information System (INIS)

Gonzalez, M.; Perez, J. M.

1996-01-01

The aim of the present work is to describe the steps followed to fabricate an ionizing radiation detector based on synthetic mercuric iodide monocrystal layers. Firstly, the crystalline orientation method has been describe, which is needed before the layer cutting perpendicularly to the (001) crystallographic. It is also defined the proceeding to crystal face finishing by a mechanical polishing and subsequent chemical etching. then, the metal electrode deposition and the view connection has been explained. Finally, the technique followed to encapsulate the detector with a polymeric thin film deposition has been described. (Author) 10 refs

HgI2 detector fabrication

International Nuclear Information System (INIS)

Gonzalez, M.; Perez, J.M.

1996-01-01

The aim of the present work is to describe the steps followed to fabricate an ionizing radiation detector based on synthetic mercuric iodide monocrystal layers. Firstly, the crystalline orientation method has been describe, which is needed before the layer cutting perpendicullarly to the (001) crystallographyc. It is also defined the proceeding to crystal face finishing by a mechanical polishing and subsequent chemical etching. Then, the metal electrode deposition and the wire connection has been explained. Finally, the technique followed to encapsulate the detector with a polimeric thin film deposition has been described

Critical element development of standard components for pipe welding/cutting by CO{sub 2} laser

Energy Technology Data Exchange (ETDEWEB)

Oka, Kiyoshi; Kakudate, Satoshi; Nakahira, Masataka [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment] [and others

1994-11-01

In D-T burning reactors such as International Thermonuclear Experimental Reactor(ITER), an internal access is inevitable for welding/cutting of cooling pipes of in-vessel components, because of spatial constraint due to a narrow port opening space. An internal-access pipe welding/cutting equipment is being developed in JAERI. Internal access is to approach through inside a pipe to a welding/cutting position, to use 10kW CO{sub 2} laser beam, and to be applicable to both welding and cutting with using a same processing head. A welding/cutting processing head with 10kW CO{sub 2} laser beam has been fabricated and the basic feasibility has been successfully demonstrated for studies of the internal-access pipe welding/cutting concept using 100-A stainless steel pipe with a thickness of 6.3mm. In this study, the optimum focal point of laser beam, laser power and traveling speed of the head have been investigated together with an adjusting mechanism of a relative distance between the head and the pipe wall. In addition, the radiation resistance of critical elements such as optical lens has been investigated. (author).

Plasma cutting or laser cutting. Plasma setsudan ka laser setsudan ka

Energy Technology Data Exchange (ETDEWEB)

Nakamura, A. (Tanaka Engineering Works Ltd., Saitama (Japan))

1991-05-01

Comparisons and discussions were made on the plasma cutting and laser cutting in sheet steel cutting, referring partly to gas cutting. Historically, the cutting has been developed from gas, plasma, and laser in that order, and currently these three methods are used mixedly. Generally, the plasma cutting is superior in cutting speed, but inferior in cut face quality, and it requires measures of dust collection. Due to high accuracy and quality in cut face, the laser cutting has been practically used for quite some time in the thin sheet industry, but medium to thick sheet cutting had a problem of unavailability of high output laser suitable for these ranges. However, the recent technologies have overcome the problem as a result of development at the authors {prime} company of a 2 kW class laser cutter capable of cutting 19 mm thick sheet. The cutter has been proven being particularly excellent in controllability. Choice of whether plasma or laser would depend upon which priority is to be taken, cost or accuracy. 15 figs., 3 tabs.

Wedge cutting of mild steel by CO 2 laser and cut-quality assessment in relation to normal cutting

Science.gov (United States)

Yilbas, B. S.; Karatas, C.; Uslan, I.; Keles, O.; Usta, Y.; Yilbas, Z.; Ahsan, M.

2008-10-01

In some applications, laser cutting of wedge surfaces cannot be avoided in sheet metal processing and the quality of the end product defines the applicability of the laser-cutting process in such situations. In the present study, CO 2 laser cutting of the wedge surfaces as well as normal surfaces (normal to laser beam axis) is considered and the end product quality is assessed using the international standards for thermal cutting. The cut surfaces are examined by the optical microscopy and geometric features of the cut edges such as out of flatness and dross height are measured from the micrographs. A neural network is introduced to classify the striation patterns of the cut surfaces. It is found that the dross height and out of flatness are influenced significantly by the laser output power, particularly for wedge-cutting situation. Moreover, the cut quality improves at certain value of the laser power intensity.

Cutting forces during turning with variable depth of cut

Directory of Open Access Journals (Sweden)

M. Sadílek

2016-03-01

The proposed research for the paper is an experimental work – measuring cutting forces and monitoring of the tool wear on the cutting edge. It compares the turning where standard roughing cycle is used and the turning where the proposed roughing cycle with variable depth of cut is applied.

Spectrally selective solar absorber with sharp and temperature dependent cut-off based on semiconductor nanowire arrays

Science.gov (United States)

Wang, Yang; Zhou, Lin; Zheng, Qinghui; Lu, Hong; Gan, Qiaoqiang; Yu, Zongfu; Zhu, Jia

2017-05-01

Spectrally selective absorbers (SSA) with high selectivity of absorption and sharp cut-off between high absorptivity and low emissivity are critical for efficient solar energy conversion. Here, we report the semiconductor nanowire enabled SSA with not only high absorption selectivity but also temperature dependent sharp absorption cut-off. By taking advantage of the temperature dependent bandgap of semiconductors, we systematically demonstrate that the absorption cut-off profile of the semiconductor-nanowire-based SSA can be flexibly tuned, which is quite different from most of the other SSA reported so far. As an example, silicon nanowire based selective absorbers are fabricated, with the measured absorption efficiency above (below) bandgap ˜97% (15%) combined with an extremely sharp absorption cut-off (transition region ˜200 nm), the sharpest SSA demonstrated so far. The demonstrated semiconductor-nanowire-based SSA can enable a high solar thermal efficiency of ≳86% under a wide range of operating conditions, which would be competitive candidates for the concentrated solar energy utilizations.

Textile sensors for stab and cut detection

Science.gov (United States)

Graßmann, C.; Obermann, M.; Lempa, E.; Bache, T.; Siegel, P. K.; Freyer, T.; Paschko, S.; Beyer, T.; Kirsche, M.; Schwarz-Pfeiffer, A.

2017-10-01

Manufacturers are aiming for more flexible and lightweight protective clothing to increase wearing comfort. A cardigan with a knitted stab-resistant inlay and an alarm system is presented. The stab-resistant inlay is based on a multilayer ultra-high molecular weight poly ethylene (UHMW-PE) fabric. Stab resistance was evaluated according to the standard of the Association of Test Laboratories for Bullet, Stab or Pike Resistant Materials and Construction Standard (VPAM 2011). Furthermore sensors for the detection of cuts and pressure were integrated. Both sensors can trigger alarms if the wearer is attacked. Normal pressure occurring through leaning on a wall or sitting is filtered out and does not trigger an alarm.

Fabrication of 238Pu based sources for energy micro-generator

International Nuclear Information System (INIS)

Barthelemy, Pierre; Boucher, Rene

1969-04-01

The authors describe the fabrication of sources of 238 Pu. The plutonium-scandium alloy is obtained by arc fusion in its delta phase. This alloy is chosen for its excellent malleability, and is rolled at 20 C. Pellets are then cut and decontaminated. Each pellet is then placed in a first tantalum sheath which is welded by electronic bombardment. A second sheath in platinum-iridium is placed around the first one, and also welded by using the same welding process. The so-fabricated sources are to feed energy thermal-electric conversion micro-generators which are supposed to operate tens of years in medical applications as organ stimulators [fr

Cutting method and cutting device for spent fuel rod of nuclear reactor

International Nuclear Information System (INIS)

Komatsu, Masahiko; Ose, Toshihiko.

1996-01-01

A control rod transferred under water in a vertically suspended state is postured horizontally at such a water depth that radiations can be shielded, and then it is cut to a dropping speed limiting portion and a cross-like main body. The separated cross-like main body portion is further cut in the longitudinal direction and separated into a pair of cut pieces each having an L-shaped cross section. A disk like metal saw is used as a cutting tool. Alternatively, a plasma jet cutter or a melting-type water jet cutter is used as a cutting tool. Then, since the spent control rod to be cut is postured horizontally under water, the water depth for the cutting position can be reduced. As a result, the cutting state using the cutting tool can be observed by naked eyes from the position above the water surface thereby enabling to perform the cutting operation reliably. (N.H.)

Flexible Laser Metal Cutting

DEFF Research Database (Denmark)

Villumsen, Sigurd; Jørgensen, Steffen Nordahl; Kristiansen, Morten

2014-01-01

This paper describes a new flexible and fast approach to laser cutting called ROBOCUT. Combined with CAD/CAM technology, laser cutting of metal provides the flexibility to perform one-of-a-kind cutting and hereby realises mass production of customised products. Today’s laser cutting techniques...... possess, despite their wide use in industry, limitations regarding speed and geometry. Research trends point towards remote laser cutting techniques which can improve speed and geometrical freedom and hereby the competitiveness of laser cutting compared to fixed-tool-based cutting technology...... such as punching. This paper presents the concepts and preliminary test results of the ROBOCUT laser cutting technology, a technology which potentially can revolutionise laser cutting....

Efecto de la crisis subprime en el valor de mercado de las empresas que conforman el IPC de la BMV en 2008 y 2009

Directory of Open Access Journals (Sweden)

María Josefina Rivero-Villar

2016-02-01

Full Text Available Entre 2004 y 2006 el incremento del 1% al 5.35% en las tasas de interés ocasionó una desaceleración en el mercado hipotecario de los Estados Unidos, lo que originó la crisis de las hipotecas Subprime que, además de afectar a su sistema financiero, permeó al mundo y dio como resultado una crisis económica generalizada en 2008. Se diseñó una investigación no experimental, cuantitativa, longitudinal y descriptiva para determinar el efecto de esta crisis en valor de mercado de las empresas que conforman el índice de precios y cotizaciones de la Bolsa Mexicana de Valores en el año 2008. Se llegó a la conclusión de que, en México, uno de los sectores más afectados fue el bursátil, que mostró una pérdida de 997,182.41 millones de pesos del valor de mercado de las empresas sujetas a estudio, como consecuencia de la corrida financiera que esta crisis ocasionó

Some possibilities for determining cutting data when using laser cutting:

OpenAIRE

Radovanović, Miroslav

2006-01-01

The technological problems faced in the field of the application of laser-cutting machines lie in insufficient knowledge of the laser technique and the absence of both sufficiently reliable practical data and knowledge about the parameters affecting the work process itself. A significant parameter that is necessary to determine and to enter in an NC-program is the cutting speed. Various authors analyze the laser-cutting process and give mathematical models where laser cutting is modeled by us...

Inactivation of Shiga toxin-producing O157:H7 and non-O157:H7 Shiga toxin-producing Escherichia coli in brine-injected, gas-grilled steaks.

Science.gov (United States)

Luchansky, John B; Porto-Fett, Anna C S; Shoyer, Bradley A; Call, Jeffrey E; Schlosser, Wayne; Shaw, William; Bauer, Nathan; Latimer, Heejeong

2011-07-01

We quantified translocation of Escherichia coli O157:H7 (ECOH) and non-O157:H7 verocytotoxigenic E. coli (STEC) into beef subprimals after brine injection and subsequently monitored their viability after cooking steaks cut therefrom. Beef subprimals were inoculated on the lean side with ca. 6.0 log CFU/g of a five-strain cocktail of rifampin-resistant ECOH or kanamycin-resistant STEC, and then passed once through an automatic brine-injector tenderizer, with the lean side facing upward. Brine solutions (9.9% ± 0.3% over fresh weight) consisted of 3.3% (wt/vol) of sodium tripolyphosphate and 3.3% (wt/vol) of sodium chloride, prepared both with (Lac(+), pH = 6.76) and without (Lac(-), pH = 8.02) a 25% (vol/vol) solution of a 60% potassium lactate-sodium diacetate syrup. For all samples injected with Lac(-) or Lac(+) brine, levels of ECOH or STEC recovered from the topmost 1 cm (i.e., segment 1) of a core sample obtained from tenderized subprimals ranged from ca. 4.7 to 6.3 log CFU/g; however, it was possible to recover ECOH or STEC from all six segments of all cores tested. Next, brine-injected steaks from tenderized subprimals were cooked on a commercial open-flame gas grill to internal endpoint temperatures of either 37.8 °C (100 °F), 48.8 °C (120 °F), 60 °C (140 °F), or 71.1 °C (160 °F). Regardless of brine formulation or temperature, cooking achieved reductions (expressed as log CFU per gram) of 0.3 to 4.1 of ECOH and 0.5 to 3.6 of STEC. However, fortuitous survivors were recovered even at 71.1 °C (160 °F) for ECOH and for STEC. Thus, ECOH and STEC behaved similarly, relative to translocation and thermal destruction: Tenderization via brine injection transferred both pathogens throughout subprimals and cooking highly contaminated, brine-injected steaks on a commercial gas grill at 71.1 °C (160 °F) did not kill all cells due, primarily, to nonuniform heating (i.e., cold spots) within the meat. Copyright ©, International Association for Food Protection

Remote Laser Cutting of CFRP: Improvements in the Cut Surface

Science.gov (United States)

Stock, Johannes; Zaeh, Michael F.; Conrad, Markus

In the automotive industry carbon fibre reinforced plastics (CFRP) are considered as a future key material to reduce the weight of the vehicle. Therefore, capable production techniques are required to process this material in mass industry. E.g., state of the art methods for cutting are limited by the high tool wear or the feasible feed rate. Laser cutting processes are still under investigation. This paper presents detailed new studies on remote laser cutting of CFRP focusing on the influence of the material properties and the quality of the cut surface. By adding light absorbing soot particles to the resin of the matrix, the cutting process is improved and fewer defects emerge.

Multibeam Fibre Laser Cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove

The appearance of the high power high brilliance fibre laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating cutting laser, the CO2-laser. However, quality problems in fibre......-laser cutting have until now limited its application in metal cutting. In this paper the first results of proof-of-principle studies applying a new approach (patent pending) for laser cutting with high brightness short wavelength lasers will be presented. In the approach, multi beam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from 2 single mode fibre lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W of single...

Multibeam fiber laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Hansen, Klaus Schütt; Nielsen, Jakob Skov

2009-01-01

The appearance of the high power high brilliance fiber laser has opened for new possibilities in laser materials processing. In laser cutting this laser has demonstrated high cutting performance compared to the dominating Cutting laser, the CO2 laser. However, quality problems in fiber......-laser cutting have until now limited its application to metal cutting. In this paper the first results of proof-of-principle Studies applying a new approach (patent pending) for laser cutting with high brightness and short wavelength lasers will be presented. In the approach, multibeam patterns are applied...... to control the melt flow out of the cut kerf resulting in improved cut quality in metal cutting. The beam patterns in this study are created by splitting up beams from two single mode fiber lasers and combining these beams into a pattern in the cut kerf. The results are obtained with a total of 550 W...

Cutting cleaner

International Nuclear Information System (INIS)

Elsen, R.P.H. van; Smits, M.

1991-01-01

This paper presents the results of a long term field test of the Cutting Cleaner, which is used for the treatment of wet oil contaminated cuttings (WOCC) produced when drilling with Oil Based Mud (OBM). It was concluded that it is possible to reduce the oil content of cuttings to an average of 1 - 2%. The recovered base oil can be reused to make new oil based mud

Tentative investigation on neutron mirror fabrication with electroless nickel plating

International Nuclear Information System (INIS)

Guo, Jiang; Morita, Shin-ya; Yamagata, Yutaka; Takeda, Shin; Kato, Jun-ichi; Hino, Masahiro; Furusaka, Michihiro

2013-01-01

Neutron optics becomes highly required due to the rapid development of neutron technology. In this paper, we attempt to fabricate the neutron mirror by using a metal substrate made of electroless nickel plating to take place of glass concerning about mirror's optical performance and manufacturing method. A new manufacture process chain of neutron mirror is proposed by following the steps of fast milling and precision cutting of aluminium/stainless, electroless nickel plating, ultra-precision cutting by diamond tools, super-smooth polishing and super mirror coating to obtain high form accuracy and good surface roughness time-efficiently. Some tentative investigations are carried out. A workpiece (□ 50 x 50 mm 2 ) with flat surface made of electroless nickel plating is machined by ultra-precision cutting and polishing. The surface roughness with 0.728 nm rms (0.588 nm Ra) is acquired. According to results of reflectometry, the neutron beam can be reflected effectively with high intensity and little scattering. (author)

Nanocarbon materials fabricated using plasmas

Science.gov (United States)

Hatakeyama, Rikizo

2017-12-01

Since the discovery of fullerenes more than three decades ago, new kinds of nanoscale materials of carbon allotropes called "nanocarbons" have so far been discovered or synthesized at successive intervals as cases such as carbon nanotubes, carbon nanohorns, graphene, carbon nanowalls, and a carbon nanobelt, while nanodiamonds were actually discovered before then. Their attractively excellent mechanical, physical, and chemical properties have driven researchers to continuously create one of the hottest frontiers in materials science and technology. While plasma states have often been involved in their discovery, on the other hand, plasma-based approaches to this exciting field originally hold promising and enormous potentials for advancing and expanding industrial/biomedical applications of nanocarbons of great diversity. This article provides an extensive overview on plasma-fabricated nanocarbon materials, where the term "fabrication" is defined as synthesis, functionalization, and assembly of devices to cover a wide range of issues associated with the step-by-step plasma processes. Specific attention has been paid to the comparative examination between plasma-based and non-plasma methods for fabricating the nanocarobons with an emphasis on the advantages of plasma processing, such as low-temperature/large-scale fabrication and diversity-carrying structure controllability. The review ends with current challenges and prospects including a ripple effect of the nanocarbon studies on the development of related novel nanomaterials such as transition metal dichalcogenides. It contains not only the latest progress in the field for cutting-edge scientists and engineers, but also the introductory guidance to non-specialists such as lower-class graduate students.

Technology development for cutting a reactor pressure vessel using a mechanical cutting technique

International Nuclear Information System (INIS)

Watanabe, Masaaki; Miyasaka, Yasuhiko; Miyao, Hidehiko; Ooki, Arahiko; Ninomiya, Toshiaki; Koiwai, Masami

2001-01-01

On decommissioning of nuclear facilities, the thermal cutting technique such as an oxygen-acetylene gas cutting and a plasma arc cutting are generally used for cutting massive and thick steel structures in consideration with cutting speed and control performance. These techniques generate dust, smoke, aerosol and a large quantity of secondary waste. Mechanical cutting technique has an advantage of small amount of secondary waste, and the metal chips from the kerf recovered easily compared with these thermal cutting technique. The remote mechanical cutting system for highly activated RPV has been developed with the manner which achieves the safety and cost effectiveness. The development has been performed on consignment to RANDEC from the Science and Technology Agency of Japan. (author)

Machining of Some Difficult-to-Cut Materials with Rotary Cutting Tools

OpenAIRE

Stjernstoft, Tero

2004-01-01

Automobile and aero industries have an increasing interestin materials with improved mechanical properties. However, manyof these new materials are classified as difficult-to-cut withconventional tools. It is obvious that tools, cutting processesand cutting models has to be devel-oped parallel to materialsscience. In this thesis rotary cutting tools are tested as analternative toexpensive diamond or cubic bore nitridetools. Metal matrix composites mostly consist of a light metalalloy (such as...

Standard Specification for Steel Blades Used with the Photovoltaic Module Surface Cut Test

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This specification specifies the recommended physical characteristics of the steel blades required for the surface cut test described in ANSI/UL 1703 (Section 24) and IEC 61730-2 (Paragraph 10.3). 1.2 ANSI/UL 1703 and IEC 61730-2 are standards for photovoltaic module safety testing. 1.3 This standard provides additional fabrication details for the surface cut test blades that are not provided in ANSI/UL 1703 or IEC 61730-2. Surface cut test blades that have out-of-tolerance corner radii or burrs are known to cause erroneous test results, either passes or failures. 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Minimizing waste (off-cuts using cutting stock model: The case of one dimensional cutting stock problem in wood working industry

Directory of Open Access Journals (Sweden)

Gbemileke A. Ogunranti

2016-09-01

Full Text Available Purpose: The main objective of this study is to develop a model for solving the one dimensional cutting stock problem in the wood working industry, and develop a program for its implementation. Design/methodology/approach: This study adopts the pattern oriented approach in the formulation of the cutting stock model. A pattern generation algorithm was developed and coded using Visual basic.NET language. The cutting stock model developed is a Linear Programming (LP Model constrained by numerous feasible patterns. A LP solver was integrated with the pattern generation algorithm program to develop a one - dimensional cutting stock model application named GB Cutting Stock Program. Findings and Originality/value: Applying the model to a real life optimization problem significantly reduces material waste (off-cuts and minimizes the total stock used. The result yielded about 30.7% cost savings for company-I when the total stock materials used is compared with the former cutting plan. Also, to evaluate the efficiency of the application, Case I problem was solved using two top commercial 1D-cutting stock software.  The results show that the GB program performs better when related results were compared. Research limitations/implications: This study round up the linear programming solution for the number of pattern to cut. Practical implications: From Managerial perspective, implementing optimized cutting plans increases productivity by eliminating calculating errors and drastically reducing operator mistakes. Also, financial benefits that can annually amount to millions in cost savings can be achieved through significant material waste reduction. Originality/value: This paper developed a linear programming one dimensional cutting stock model based on a pattern generation algorithm to minimize waste in the wood working industry. To implement the model, the algorithm was coded using VisualBasic.net and linear programming solver called lpsolvedll (dynamic

Fabrication of cavities in low loss LTCC materials for microwave applications

International Nuclear Information System (INIS)

Malecha, Karol

2012-01-01

A method of buried cavity fabrication in low loss DP951 and new DP9K7 LTCC (low-temperature co-fired ceramic) materials is described in this paper. Laser micromachining and method based on sacrificial volume material (SVM) are studied. Cavities are fabricated in LTCC materials using two different SVMs—cetyl alcohol and carbon tape. The influence of laser system parameters on cutting quality of the LTCC materials is studied. Moreover, thermal properties of the LTCCs and used SVMs are analyzed using combined thermo-gravimetric analysis, differential thermal analysis and differential thermo-gravimetry. Geometries of the LTCC test structures fabricated using different SVMs are analyzed using a scanning electron microscope and x-ray tomography. Energy dispersive spectroscopy and surface wettability measurements are used to analyze changes in LTCC materials atomic composition after co-firing with SVMs. (paper)

Fabrication of a First Article Lightweight Composite Technology Demonstrator - Exospine

Science.gov (United States)

2014-01-01

core, (b) 0/90, and (c) ± 45 ply cuts of ACG-MTM 45-1/CF0526 prepreg fabric...Materials, University of Delaware (UD-CCM, Newark, DE) for providing the laminate design and materials used in this work. The authors would also like...onboard diagnostics. 2. Experimental 2.1 Materials Plain woven carbon fiber/epoxy prepreg and a low-density foam core were provided to ARL for the

Design and accuracy analysis of a metamorphic CNC flame cutting machine for ship manufacturing

Science.gov (United States)

Hu, Shenghai; Zhang, Manhui; Zhang, Baoping; Chen, Xi; Yu, Wei

2016-09-01

The current research of processing large size fabrication holes on complex spatial curved surface mainly focuses on the CNC flame cutting machines design for ship hull of ship manufacturing. However, the existing machines cannot meet the continuous cutting requirements with variable pass conditions through their fixed configuration, and cannot realize high-precision processing as the accuracy theory is not studied adequately. This paper deals with structure design and accuracy prediction technology of novel machine tools for solving the problem of continuous and high-precision cutting. The needed variable trajectory and variable pose kinematic characteristics of non-contact cutting tool are figured out and a metamorphic CNC flame cutting machine designed through metamorphic principle is presented. To analyze kinematic accuracy of the machine, models of joint clearances, manufacturing tolerances and errors in the input variables and error models considering the combined effects are derived based on screw theory after establishing ideal kinematic models. Numerical simulations, processing experiment and trajectory tracking experiment are conducted relative to an eccentric hole with bevels on cylindrical surface respectively. The results of cutting pass contour and kinematic error interval which the position error is from-0.975 mm to +0.628 mm and orientation error is from-0.01 rad to +0.01 rad indicate that the developed machine can complete cutting process continuously and effectively, and the established kinematic error models are effective although the interval is within a `large' range. It also shows the matching property between metamorphic principle and variable working tasks, and the mapping correlation between original designing parameters and kinematic errors of machines. This research develops a metamorphic CNC flame cutting machine and establishes kinematic error models for accuracy analysis of machine tools.

A system automatic study for the spent fuel rod cutting and simulated fuel pellet extraction device

International Nuclear Information System (INIS)

Jeong, J. H.; Yun, J. S.; Hong, D. H.; Kim, Y. H.; Park, K. Y.

2001-01-01

A fuel pellet extraction device of the spent fuel rods is described. The device consists of a cutting device of the spent fuel rods and the decladding device of the fuel pellets. The cutting device is to cut a spent fuel rod to n optimal size for fast decladding operation. To design the device, the fuel rod properties are investigated including the dimension and material of fuel rod tubes and pellets. Also, various methods of existing cutting method are investigated. The design concepts accommodate remote operability for the Hot-Cell(radioactive ) area operation. Also, the modularization of the device structure is considered for the easy maintenance. The decladding device is to extract the fuel pellet from the rod cut. To design this device, the existing method is investigated including the chemical and mechanical decladding methods. From the view point of fuel recovery and feasibility of implementation. it is concluded that the chemical decladding method is not appropriate due to the mass production of radioactive liquid wastes, in spite of its high fuel recovery characteristics. Hence, in this paper, the mechanical decladding method is adopted and the device is designed so as to be applicable to various lengths of rod-cuts. As like the cutting device,the concepts of remote operability and maintainability is considered. Both devices are fabricated and the performance is investigated through a series of experiments. From the experimental result, the optimal operational condition of the devices is established

Lateral and axial cutting efficiency of instruments manufactured with conventional nickel-titanium and novel gold metallurgy.

Science.gov (United States)

Vasconcelos, R A; Arias, A; Peters, O A

2018-05-01

To isolate the effect of metallurgy in lateral and axial cutting efficacy against plastic and bovine dentine substrates by comparing two rotary systems with identical design but manufactured with either conventional nickel-titanium or heat-treated gold alloy. A total of 258 ProTaper Universal (PTU) and ProTaper Gold (PTG) Shaping instruments were used. Bending behaviour was assessed to determine the appropriate displacement associated with a 2 N force in lateral cutting. Ten instruments of each type were used in lateral action for 60 s against bovine dentine or plastic substrates four consecutive times producing four notches in each specimen. Ten further instruments of each type were used in on axial action in four standardized simulated root canals fabricated from 4-mm thick plastic or dentine discs. Both tests were performed at 300 rpm in a computer-controlled testing platform. Notch area and torsional load were compared with Student's t-tests. Repeated measures ANOVA was used to compare cutting efficiency across the four different time-points. Pearson correlation coefficients between substrates were also determined. For lateral action, all three PTG instruments cut significantly more effectively (P cut significantly more after 120 and 180 s (P cutting at 180 s on plastic and 120 s on bovine dentine (P cutting efficiency when compared to those made from conventional nickel-titanium. © 2017 International Endodontic Journal. Published by John Wiley & Sons Ltd.

A Cost-Effective, In-House, Positioning and Cutting Guide System for Orthognathic Surgery.

Science.gov (United States)

McAllister, Peter; Watson, Melanie; Burke, Ezra

2018-03-01

Technological advances in 3D printing can dramatically improve orthognathic surgical planning workflow. Custom positioning and cutting guides enable intraoperative reproduction of pre-planned osteotomy cuts and can result in greater surgical accuracy and patient safety. This short paper describes the use of freeware (some with open-source) combined with in-house 3D printing facilities to produce reliable, affordable osteotomy cutting guides. Open-source software (3D Slicer) is used to visualise and segment three-dimensional planning models from imported conventional computed tomography (CT) scans. Freeware (Autodesk Meshmixer ©) allows digital manipulation of maxillary and mandibular components to plan precise osteotomy cuts. Bespoke cutting guides allow exact intraoperative positioning. These are printed in polylactic acid (PLA) using a fused-filament fabrication 3D printer. Fixation of the osteotomised segments is achieved using plating templates and four pre-adapted plates with planned screw holes over the thickest bone. We print maxilla/ mandible models with desired movements incorporated to use as a plating template. A 3D printer capable of reproducing a complete skull can be procured for £1000, with material costs in the region of £10 per case. Our production of models and guides typically takes less than 24 hours of total print time. The entire production process is frequently less than three days. Externally sourced models and guides cost significantly more, frequently encountering costs totalling £1500-£2000 for models and guides for a bimaxillary osteotomy. Three-dimensional guided surgical planning utilising custom cutting guides enables the surgeon to determine optimal orientation of osteotomy cuts and better predict the skeletal maxilla/mandible relationship following surgery. The learning curve to develop proficiency using planning software and printer settings is offset by increased surgical predictability and reduced theatre time, making this

Underwater cutting techniques developments

International Nuclear Information System (INIS)

Bach, F.-W.

1990-01-01

The primary circuit structures of different nuclear powerplants are constructed out of stainless steels, ferritic steels, plated ferritic steels and alloys of aluminium. According to the level of the specific radiation of these structures, it is necessary for dismantling to work with remote controlled cutting techniques. The most successful way to protect the working crew against exposure of radiation is to operate underwater in different depths. The following thermal cutting processes are more or less developed to work under water: For ferritic steels only - flame cutting; For ferritic steels, stainless steels, cladded steels and aluminium alloys - oxy-arc-cutting, arc-waterjet-cutting with a consumable electrode, arc-saw-cutting, plasma-arc-cutting and plasma-arc-saw. The flame cutting is a burning process, all the other processes are melt-cutting processes. This paper explains the different techniques, giving a short introduction of the theory, a discussion of the possibilities with the advantages and disadvantages of these processes giving a view into the further research work in this interesting field. (author)

Welding and cutting

International Nuclear Information System (INIS)

Drews, P.; Schulze Frielinghaus, W.

1978-01-01

This is a survey, with 198 literature references, of the papers published in the fields of welding and cutting within the last three years. The subjects dealt with are: weldability of the materials - Welding methods - Thermal cutting - Shaping and calculation of welded joints - Environmental protection in welding and cutting. (orig.) [de

Cutting assembly

Science.gov (United States)

Racki, Daniel J.; Swenson, Clark E.; Bencloski, William A.; Wineman, Arthur L.

1984-01-01

A cutting apparatus includes a support table mounted for movement toward and away from a workpiece and carrying a mirror which directs a cutting laser beam onto the workpiece. A carrier is rotatably and pivotally mounted on the support table between the mirror and workpiece and supports a conduit discharging gas toward the point of impingement of the laser beam on the workpiece. Means are provided for rotating the carrier relative to the support table to place the gas discharging conduit in the proper positions for cuts made in different directions on the workpiece.

Restraining and neck cutting or stunning and neck cutting of veal calves.

Science.gov (United States)

Lambooij, E; van der Werf, J T N; Reimert, H G M; Hindle, V A

2012-05-01

Brain and heart activities were measured in 31 veal calves during restraining and rotating followed by neck cutting with or without stunning to evaluate welfare. After neck cutting correlation dimension analyses and %power of EEG beta wave fraction decreased gradually to lower values resulting in an induction of unconsciousness lasting on average 80s. Corneal reflex response ceased 135±57s after neck cutting. The CD scores and the %power of beta waves fell immediately after post-cut captive bolt and pre-cut electrical stunning to levels indicating unconsciousness. Heart rate in lairage increased upon entrance to the restrainer and again after rotation, heart rate variability decreased. Rotating the restrainer 90°, 120° or 180° compromised veal calf welfare and should be avoided. It is recommended to use post-cut captive bolt stunning or pre-cut electrical stunning inducing immediate unconsciousness. Copyright © 2011 Elsevier Ltd. All rights reserved.

Development of an innovative device for ultrasonic elliptical vibration cutting.

Science.gov (United States)

Zhou, Ming; Hu, Linhua

2015-07-01

An innovative ultrasonic elliptical vibration cutting (UEVC) device with 1st resonant mode of longitudinal vibration and 3rd resonant mode of bending vibration was proposed in this paper, which can deliver higher output power compared to previous UEVC devices. Using finite element method (FEM), resonance frequencies of the longitudinal and bending vibrations were tuned to be as close as possible in order to excite these two vibrations using two-phase driving voltages at a single frequency, while wave nodes of the longitudinal and bending vibrations were also adjusted to be as coincident as possible for mounting the device at a single fixed point. Based on the simulation analysis results a prototype device was fabricated, then its vibration characteristics were evaluated by an impedance analyzer and a laser displacement sensor. With two-phase sinusoidal driving voltages both of 480 V(p-p) at an ultrasonic frequency of 20.1 kHz, the developed prototype device achieved an elliptical vibration with a longitudinal amplitude of 8.9 μm and a bending amplitude of 11.3 μm. The performance of the developed UEVC device is assessed by the cutting tests of hardened steel using single crystal diamond tools. Experimental results indicate that compared to ordinary cutting process, the tool wear is reduced significantly by using the proposed device. Copyright © 2015 Elsevier B.V. All rights reserved.

Study on the Optimum Cutting Parameters of an Aluminum Mold for Effective Bonding Strength of a PDMS Microfluidic Device

Directory of Open Access Journals (Sweden)

Caffiyar Mohamed Yousuff

2017-08-01

Full Text Available Master mold fabricated using micro milling is an easy way to develop the polydimethylsiloxane (PDMS based microfluidic device. Achieving high-quality micro-milled surface is important for excellent bonding strength between PDMS and glass slide. The aim of our experiment is to study the optimal cutting parameters for micro milling an aluminum mold insert for the production of a fine resolution microstructure with the minimum surface roughness using conventional computer numerical control (CNC machine systems; we also aim to measure the bonding strength of PDMS with different surface roughnesses. Response surface methodology was employed to optimize the cutting parameters in order to obtain high surface smoothness. The cutting parameters were demonstrated with the following combinations: 20,000 rpm spindle speed, 50 mm/min feed rate, depth of cut 5 µm with tool size 200 µm or less; this gives a fine resolution microstructure with the minimum surface roughness and strong bonding strength between PDMS–PDMS and PDMS–glass.

Fabrication progress of the ITER vacuum vessel sector in Korea

Energy Technology Data Exchange (ETDEWEB)

Kim, B.C., E-mail: bckim@nfri.re.kr [National Fusion Research Institute, Gwahangno 113, Yuseong-gu, Daejeon (Korea, Republic of); Lee, Y.J.; Hong, K.H.; Sa, J.W.; Kim, H.S.; Park, C.K.; Ahn, H.J.; Bak, J.S.; Jung, K.J. [National Fusion Research Institute, Gwahangno 113, Yuseong-gu, Daejeon (Korea, Republic of); Park, K.H.; Roh, B.R.; Kim, T.S.; Lee, J.S.; Jung, Y.H.; Sung, H.J.; Choi, S.Y.; Kim, H.G.; Kwon, I.K.; Kwon, T.H. [Hyundai Heavy Industries Co. Ltd., Dong-gu, Ulsan (Korea, Republic of)

2013-10-15

Highlights: ► Fabrication of ITER vacuum vessel sector full scale mock-up to develop fabrication procedures. ► The welding and nondestructive examination techniques conform to RCC-MR. ► The preparation of real manufacturing of ITER vacuum vessel sector. -- Abstract: As a participant of ITER project, ITER Korea has to supply two ITER vacuum vessel sectors (Sector no. 6, no. 1) of total nine ITER VV sectors. After the procurement arrangement with ITER Organization, ITER Korea made the contract with Hyundai Heavy Industries (HHI) for fabrication of two sectors. Then the start of the manufacturing design was initiated from January 2010. HHI made three real scale R and D mock-ups to verify the critical fabrication feasibility issues on electron beam welding, 3D forming, welding distortion and achievable tolerances. The documentation according to IO and the French nuclear safety regulation requirement, the qualification of welding and nondestructive examination procedures conform to RCC-MR 2007 were proceed in parallel. The mass production of raw material was done after receiving ANB (agreed notified body) verification of product/parts and shop qualification. The manufacturing drawing, manufacturing and inspection plan of VV sector with supporting fabrication procedures are also verified by ANB, accordingly the first cutting and forming of plates for VV sector fabrication started from February 2012. This paper reports the latest fabrication progress of ITER vacuum vessel Sector no. 6 that will be assembled as the first sector in the ITER pit. The overall fabrication route, R and D mock-up fabrication results with forming and welding distortion analysis, qualification status of welding and nondestructive examination (NDE) are also presented.

Paper Cuts.

Science.gov (United States)

Greene, Lisa A.

1990-01-01

Describes how to create paper cuts and suggests the most appropriate materials for young children that give good quality results. Describes the methods the author, a professional artist, uses to assemble her own paper cuts and how these can be adopted by older students. (KM)

Operation of the AM-50 cutting head under different cutting conditions

Energy Technology Data Exchange (ETDEWEB)

Sikora, W; Kusz, F; Fels, M

1988-02-01

Presents results of investigations into operation of the AM-50 heading machine. About 50% of headings, i.e. about 800 km/a, are driven by about 400 heading machines. It has been found that energy consumption depends on compression strength of rock and is 6 times higher for sandstone than for clayey shale. Power consumed by cutting heads depends mainly on the web used (30-150 mm depending on rock strength). Wear of cutting tools is 1-30 pieces per meter of heading advance at a working cross-section area of 15 m/sup 2/. The AM-50 machine uses cutting speeds of 1.1-3.5 m/s. Higher speeds negatively affect the resistance to cutting. Nonuniform tool wear on the cutting head circumference is an indication of improper head design that requires remedying.

Wet cutting

Energy Technology Data Exchange (ETDEWEB)

Hole, B. [IMC Technical Services (United Kingdom)

1999-08-01

Continuous miners create dust and methane problems in underground coal mining. Control has usually been achieved using ventilation techniques as experiments with water based suppression have led to flooding and electrical problems. Recent experience in the US has led to renewed interest in wet head systems. This paper describes tests of the Hydraphase system by IMC Technologies. Ventilation around the cutting zone, quenching of hot ignition sources, dust suppression, the surface trial gallery tests, the performance of the cutting bed, and flow of air and methane around the cutting head are reviewed. 1 ref., 2 figs., 2 photos.

Fundamentals of cutting.

Science.gov (United States)

Williams, J G; Patel, Y

2016-06-06

The process of cutting is analysed in fracture mechanics terms with a view to quantifying the various parameters involved. The model used is that of orthogonal cutting with a wedge removing a layer of material or chip. The behaviour of the chip is governed by its thickness and for large radii of curvature the chip is elastic and smooth cutting occurs. For smaller thicknesses, there is a transition, first to plastic bending and then to plastic shear for small thicknesses and smooth chips are formed. The governing parameters are tool geometry, which is principally the wedge angle, and the material properties of elastic modulus, yield stress and fracture toughness. Friction can also be important. It is demonstrated that the cutting process may be quantified via these parameters, which could be useful in the study of cutting in biology.

Geography of opportunity and residential mortgage foreclosure: A spatial analysis of a U.S. housing market

Directory of Open Access Journals (Sweden)

Yanmei LI

2011-12-01

Full Text Available South Florida has been among the top foreclosure markets in the United States, but little research has explored whether this market presents different dynamics compared to other metropolitan areas. This research chooses Broward County to explore whether socioeconomic characteristics and certain public policy instruments relate to subprime lending and mortgage foreclosure patterns. Results indicate areas bounded by linear highways and railroads have a concentration of low-income black population and subprime loans. The spatial distribution of subprime loans is mostly explained by a higher percentage of minority and/or Hispanic population in a neighborhood. Yet, racial minorities, instead of Hispanic origin, contributes mostly to the concentration of subprime loans. The spatial pattern of foreclosures is more complex, determined not only by subprime loans but also possibly other factors associated with the mortgage crisis. This suggests that disadvantaged neighborhoods are disproportionally lacking favorable opportunities due to institutional and sub- cultural forces shaping the geography of subprime and foreclosure.

On the Cutting Performance of Segmented Diamond Blades when Dry-Cutting Concrete.

Science.gov (United States)

Sánchez Egea, A J; Martynenko, V; Martínez Krahmer, D; López de Lacalle, L N; Benítez, A; Genovese, G

2018-02-09

The objective of the present study is to analyze and compare the cutting performance of segmented diamond blades when dry-cutting concrete. A cutting criteria is proposed to characterize the wear of the blades by measuring the variation of the external diameter and the weight loss of the blade. The results exhibit the cutting blade SB-A, which has twice the density of diamonds and large contact area, exhibits less wear even though the material removal rate is higher compared with the other two cutting blades. Additionally, the surface topography of the different blades is evaluated to examine the impact of wear depending on the surface profile and the distribution of the diamonds in the blade's matrix. Large number of diamonds pull-out are found in blades type SB-C, which additionally shows the worst wear resistant capability. As a conclusion, the cutting efficiency of the blade is found to be related to the density of embedded diamonds and the type of the surface profile of the cutting blade after reaching the stop criteria.

Production of a textile reinforced concrete protective layers with non-woven polypropylene fabric

Science.gov (United States)

Žák, J.; Štemberk, P.; Vodička, J.

2017-09-01

Textile concrete with nonwoven polypropylene fabric can be used for protective layers of reinforced concrete structures, reducing the thickness of the cover layer or reducing the water penetration rate into the structure. The material consists of cement matrix with finegrained aggregate and nonwoven textile reinforcement. The maximum grain size of the mixture suitable for the nonwoven textile infiltration is 0.25 mm. The interlayer contains larger aggregates and short fibers. Tensile loading causes a large amount of microcracks in the material. The material can withstand strain over 25% without collapsing. Increased quality and water-cement ratio reduction was achieved using the plasticizers and distribution of the mixture into a fabric using a vibrating trowel. It is possible to make flat plates and even curved structures from this material. Larger curvatures of structures should be solved by cutting and overlapping the fabric. Small curvatures can be solved within the deformability of the fabric. Proper infiltration of the cement mixture into the fabric is the most important task in producing this material.

Device for cutting protrusions

Science.gov (United States)

Bzorgi, Fariborz M [Knoxville, TN

2011-07-05

An apparatus for clipping a protrusion of material is provided. The protrusion may, for example, be a bolt head, a nut, a rivet, a weld bead, or a temporary assembly alignment tab protruding from a substrate surface of assembled components. The apparatus typically includes a cleaver having a cleaving edge and a cutting blade having a cutting edge. Generally, a mounting structure configured to confine the cleaver and the cutting blade and permit a range of relative movement between the cleaving edge and the cutting edge is provided. Also typically included is a power device coupled to the cutting blade. The power device is configured to move the cutting edge toward the cleaving edge. In some embodiments the power device is activated by a momentary switch. A retraction device is also generally provided, where the retraction device is configured to move the cutting edge away from the cleaving edge.

AC Loss Reduction in Filamentized YBCO Coated Conductors with Virtual Transverse Cross-cuts

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yifei [ORNL; Duckworth, Robert C [ORNL; Ha, Tam T [ORNL; List III, Frederick Alyious [ORNL; Gouge, Michael J [ORNL; Chen, Y [SuperPower Incorporated, Schenectady, New York; X, Xiong, [SuperPower Incorporated, Schenectady, New York; Selvamanickam, V. [SuperPower Incorporated, Schenectady, New York

2011-01-01

While the performance of YBa{sub 2}Cu{sub 3}O{sub 7-x} (YBCO)-based coated conductors under dc currents has improved significantly in recent years, filamentization is being investigated as a technique to reduce ac loss so that the 2nd generation (2G) high temperature superconducting (HTS) wires can also be utilized in various ac power applications such as cables, transformers and fault current limiters. Experimental studies have shown that simply filamentizing the superconducting layer is not effective enough to reduce ac loss because of incomplete flux penetration in between the filaments as the length of the tape increases. To introduce flux penetration in between the filaments more uniformly and further reduce the ac loss, virtual transverse cross-cuts were made in superconducting filaments of the coated conductors fabricated using the metal organic chemical vapor deposition (MOCVD) method. The virtual transverse cross-cuts were formed by making cross-cuts (17 - 120 {micro}m wide) on the IBAD (ion beam assisted deposition)-MgO templates using laser scribing followed by depositing the superconducting layer ({approx} 0.6 {micro}m thick). AC losses were measured and compared for filamentized conductors with and without the cross-cuts under applied peak ac fields up to 100 mT. The results were analyzed to evaluate the efficacy of filament decoupling and the feasibility of using this method to achieve ac loss reduction.

Study of Cutting Edge Temperature and Cutting Force of End Mill Tool in High Speed Machining

Directory of Open Access Journals (Sweden)

Kiprawi Mohammad Ashaari

2017-01-01

Full Text Available A wear of cutting tools during machining process is unavoidable due to the presence of frictional forces during removing process of unwanted material of workpiece. It is unavoidable but can be controlled at slower rate if the cutting speed is fixed at certain point in order to achieve optimum cutting conditions. The wear of cutting tools is closely related with the thermal deformations that occurred between the frictional contact point of cutting edge of cutting tool and workpiece. This research paper is focused on determinations of relationship among cutting temperature, cutting speed, cutting forces and radial depth of cutting parameters. The cutting temperature is determined by using the Indium Arsenide (InAs and Indium Antimonide (InSb photocells to measure infrared radiation that are emitted from cutting tools and cutting forces is determined by using dynamometer. The high speed machining process is done by end milling the outer surface of carbon steel. The signal from the photocell is digitally visualized in the digital oscilloscope. Based on the results, the cutting temperature increased as the radial depth and cutting speed increased. The cutting forces increased when radial depth increased but decreased when cutting speed is increased. The setup for calibration and discussion of the experiment will be explained in this paper.

The Cutting Process, Chips and Cutting Forces in Machining CFRP

DEFF Research Database (Denmark)

Koplev, A.; Lystrup, Aage; Vorm, T.

1983-01-01

The cutting of unidirectional CFRP, perpendicular as well as parallel to the fibre orientation, is examined. Shaping experiments, ‘quick-stop’ experiments, and a new chip preparation technique are used for the investigation. The formation of the chips, and the quality of the machined surface...... is discussed. The cutting forces parallel and perpendicular to the cutting direction are measured for various parameters, and the results correlated to the formation of chips and the wear of the tool....

Fabrication of beta particles detector for RMS

International Nuclear Information System (INIS)

Lee, W. G.; Kim, Y. G.; Kim, J. B.; Jeong, J. E.; Hong, S. B.

2003-01-01

The beta particles detector for RMS (radiation monitoring system) was fabricated to detect charged beta particles. The plastic scintillator was cutted, shaped, polished to make plastic disk for beta particles. The diameter of completed plastic scintillator disk is 40 mm and thickness is 1.5 mm. The mylar film and aluminium foil were used the front of plastic scintillator to intercept light and moisture. The completed plastic detector for RMS consist of the discriminator and counter were made by ULS (Co.). The absolute efficiency of plastic detector was 45.51% for beta particles (Sr/Y - 90)

Design and fabrication of topologically optimized structures;

DEFF Research Database (Denmark)

Feringa, Jelle; Søndergaard, Asbjørn

2012-01-01

Integral structural optimization and fabrication seeks the synthesis of two original approaches; that of topological optimization (TO) and robotic hotwire cutting (HWC) (Mcgee 2011). TO allows for the reduction of up to 70% of the volume of concrete to support a given structure (Sondergaard...... & Dombernowsky 2011). A strength of the method is that it allows to come up with structural designs that lie beyond the grasp of traditional means of design. A design space is a discretized volume, delimiting where the optimization will take place. The number of cells used to discretize the design space thus...

Fabrication and characterization of a carbon nanotube-based nanoknife

International Nuclear Information System (INIS)

Singh, G; Rice, P; Mahajan, R L; McIntosh, J R

2009-01-01

We demonstrate the fabrication and testing of a prototype microtome knife based on a multiwalled carbon nanotube (MWCNT) for cutting ∼100 nm thick slices of frozen-hydrated biological samples. A piezoelectric-based 3D manipulator was used inside a scanning electron microscope (SEM) to select and position individual MWCNTs, which were subsequently welded in place using electron beam-induced deposition. The knife is built on a pair of tungsten needles with provision to adjust the distance between the needle tips, accommodating various lengths of MWCNTs. We performed experiments to test the mechanical strength of a MWCNT in the completed device using an atomic force microscope tip. An increasing force was applied at the mid-point of the nanotube until failure occurred, which was observed in situ in the SEM. The maximum breaking force was approximately (8 x 10 -7 ) N which corresponds well with the typical microtome cutting forces reported in the literature. In situ cutting experiments were performed on a cell biological embedding plastic (epoxy) by pushing it against the nanotube. Initial experiments show indentation marks on the epoxy surface. Quantitative analysis is currently limited by the surface asperities, which have the same dimensions as the nanotube.

Analysis of changes in paper cutting forces during the cutting cycle in single-knife guillotine

OpenAIRE

Rusin, Agnieszka; Petriaszwili, Georgij

2013-01-01

Paper presents the results of changes in the three components of cutting forces of paper stacks cutting during the cutting cycle in single-knife guillotine. The changes of the three components of cutting force at different stages of cutting cycle were analyzed.

COMPORTAMENTO DOS DEZ MAIORES BANCOS BRASILEIROS DURANTE A CRISE DO SUBPRIME: UMA ANÁLISE POR MEIO DE INDICADORES CONTÁBEIS

Directory of Open Access Journals (Sweden)

Rosane Maria Pio da Silva

Full Text Available O presente artigo tem por objetivo demonstrar o comportamento dos dez maiores bancos brasileiros no período de junho de 2008 a de setembro de 2009, a partir da análise de indicadores contábeis. Para tanto, foram calculados 16 índices com periodicidade trimestral, extraídos a partir das informações contidas nos relatórios contábeis, caracterizando a pesquisa como documental. Os índices foram separados em cinco categorias: liquidez, capital, rentabilidade, receita e mercado. Os resultados obtidos apontaram que a maioria das instituições financeiras da amostra teve capacidade de gerir seus recursos de forma a obter condições de manter o crédito inicialmente, para então, a partir do primeiro trimestre de 2009, impulsionada pelos bancos públicos, elevar suas operações de crédito. Além disso, a maioria dos bancos apresentou uma tendência anticíclica de fomentar as atividades produtivas, com preferência às atividades de maior liquidez em detrimento da rentabilidade, tendo dessa forma uma postura mais conservadora. Por fim, verificou-se que as iniciativas adotadas pelo governo, o equilíbrio econômico brasileiro e os recursos oferecidos pelos bancos ajudaram a produzir um ambiente para o reaquecimento das atividades empresariais durante o período mais agudo da crise do subprime.

Cutting and Self-Harm

Science.gov (United States)

... Your feelings Feeling sad Cutting and self-harm Cutting and self-harm Self-harm, sometimes called self- ... There are many types of self-injury, and cutting is one type that you may have heard ...

Efecto manada en sectores económicos de las bolsas latinoamericanas: una visión pre y poscrisis subprime

Directory of Open Access Journals (Sweden)

Juan Benjamín Duarte Duarte

2016-01-01

Full Text Available En los últimos a ̃ nos, el comportamiento de los agentes y lo que los motiva a tomar sus decisiones de inversión ha sido foco de estudio de muchos investigadores en las ramas de economía, finanzas y afines. Teniendo en cuenta esto, en este artículo se busca comprobar empíricamente uno de estos comportamientos, el efecto manada, mediante los modelos propuestos por Christie y Huang (1995 y Chang, Cheng y Khorana (2000, en el índice más representativo y en los sectores que lo componen, de los principales mercados de América Latina (Brasil, México, Chile, Colombia, Perú y Argentina para el periodo 2002-2014, así como en los subperiodos pre y poscrisis originados por las hipotecas subprime. Los hallazgos de esta investigación muestran que el efecto manada está presente en el índice más representativo del mercado bursátil de Colombia, Chile y Perú y en algunos de los sectores que lo componen, ya sea en el periodo total y/o en los subperiodos de pre y poscrisis; en el mercado de Brasil, el efecto está presente en el sector bancario en el periodo total y en el subperiodo de precrisis; en el mercado de Argentina tal efecto se presentó en el sector bancario y en el sector de petróleo y gas, y en el mercado de México no existe ninguna evidencia de dicho efecto

Causal Nexus between Stock Price, Demand for Money, Interest Rate, Foreign Institutional Investment, and Exchange Rates in India: A Post Subprime Crisis Analysis

Directory of Open Access Journals (Sweden)

Iti Vyas

2014-08-01

Full Text Available This  paper  makes  an  attempt  to  empirically  examine  the  causal  nexus  between  stock price, demand for money, interest rates, foreign institutional investment and exchange rates in India in the post subprime mortgage crisis period. The study employed Granger causality test, Vector Auto Regression and Johansen Maximum Likelihood procedure to examine the short  run  and  long  run  dynamic  interaction  among  the  above  mentioned  variables  for  the period January 1993 to May 2009. The major indings of the study are: stock return affects exchange rate return, net foreign institutional investment and growth of demand for money. Growth  of  demand  for  money,  in  turn,  affects  interest  rate.  Interest  rate  is  more  affected by exchange rate return. Foreign institutional investment also affects interest rate. The co-integration  test  conirms  that  there  does  not  exist  any  long  run  equilibrium  relationship between stock return and exchange rate return ";} // -->activate javascript

On Permuting Cut with Contraction

OpenAIRE

Borisavljevic, Mirjana; Dosen, Kosta; Petric, Zoran

1999-01-01

The paper presents a cut-elimination procedure for intuitionistic propositional logic in which cut is eliminated directly, without introducing the multiple-cut rule mix, and in which pushing cut above contraction is one of the reduction steps. The presentation of this procedure is preceded by an analysis of Gentzen's mix-elimination procedure, made in the perspective of permuting cut with contraction. It is also shown that in the absence of implication, pushing cut above contraction doesn't p...

Experimental research on the machinability of Hardox steel by abrasive waterjet cutting

Directory of Open Access Journals (Sweden)

Filip Alexandru Catalin

2017-01-01

Full Text Available One of the main present industry challenges is finding the most efficient manufacturing process for a certain part. When parts are made of strong steels like Hardox, their fabrication method is usually difficult. Abrasive waterjet cutting (AWJ is one of the cutting processes which can be used in this case. This paper presents an experimental research on the machinability of Hardox steel by AWJ. The experiments were conducted using a factorial design model considering two of the main influence parameters like the traverse speed and the distance between the nozzle and the surface of the material. Based on the measurement of the dimensions and the roughness of the parts, the influence of the parameters was revealed and analyzed. The manufacturing time was also compared, as it directly influences the production cost. Further research is considered to develop a mathematical model which can be used for a proper choice of the process parameters depending on the initial requirements.

Model for Reggeon-Pomeranchukon cuts

International Nuclear Information System (INIS)

Chia, S.

1977-01-01

A model is presented for calculating Reggeon-Pomeranchukon cuts, making use explicitly of the Mandelstam diagram. External spins are treated in a natural way. Calculation for the general case is outlined and it is shown that in practical application the cut can be calculated in a standard way. Cuts associated with the exchanges of π, rho, B, and A 2 are considered, and characteristics of the RP cuts, as well as the structure functions, are extracted and discussed. It is found that the model differs considerably from the absorption model. Two suppression schemes are operative which control the magnitudes of cut contributions to amplitudes with ''naturality'' opposite to the Reggeon. The πP cut is found to be a unique case because of the smallness of the pion mass. In general, the RP cuts are self-conspiratorial. At very high energies, all cuts, except πP cut, exhibit quasifactorization

Cutting method for structural component into block like shape, and device used for cutting

International Nuclear Information System (INIS)

Nakazawa, Koichi; Ito, Akira; Tateiwa, Masaaki.

1995-01-01

Two grooves each of a predetermined depth are formed along a surface of a structural component, and a portion between the two grooves is cut in the direction of the depth from the surface of the structural component by using a cutting wire of a wire saw device. Then, the cutting wire is moved in the extending direction of the grooves while optionally changing the position in the direction of the depth to conduct cutting for the back face. Further, the cutting wire is moved in the direction of the depth of the groove toward the surface, to cut a portion between the two grooves. The wire saw device comprises a wire saw main body movable along the surface of the structural component, a pair of wire guide portions extending in the direction of the depth, guide pooleys capable of guiding the cutting wire guides revolvably and rotatably disposed at the top end, and an endless annular cutting wire extending between the wire guide portions. Thus, it is possible to continuously cut out blocks set to optional size and thickness. In addition, remote cutting is possible with no requirement for an operator to access to the vicinity of radioactivated portions. (N.H.)

An FMS Dynamic Production Scheduling Algorithm Considering Cutting Tool Failure and Cutting Tool Life

International Nuclear Information System (INIS)

Setiawan, A; Wangsaputra, R; Halim, A H; Martawirya, Y Y

2016-01-01

This paper deals with Flexible Manufacturing System (FMS) production rescheduling due to unavailability of cutting tools caused either of cutting tool failure or life time limit. The FMS consists of parallel identical machines integrated with an automatic material handling system and it runs fully automatically. Each machine has a same cutting tool configuration that consists of different geometrical cutting tool types on each tool magazine. The job usually takes two stages. Each stage has sequential operations allocated to machines considering the cutting tool life. In the real situation, the cutting tool can fail before the cutting tool life is reached. The objective in this paper is to develop a dynamic scheduling algorithm when a cutting tool is broken during unmanned and a rescheduling needed. The algorithm consists of four steps. The first step is generating initial schedule, the second step is determination the cutting tool failure time, the third step is determination of system status at cutting tool failure time and the fourth step is the rescheduling for unfinished jobs. The approaches to solve the problem are complete-reactive scheduling and robust-proactive scheduling. The new schedules result differences starting time and completion time of each operations from the initial schedule. (paper)

Advanced cutting techniques: laser and fissuration cutting

International Nuclear Information System (INIS)

Migliorati, B.; Gay, P.

1984-01-01

Experimental tests have been performed using CO 2 laser with output power 1 to 15 kW to evaluate the effect of varying the following parameters: material (carbon steel Fe 42 C, stainless steel AISI 304, concrete), laser power, beam characteristics, work piece velocity, gas type and distribution on the laser interaction zone. In the case of concrete, drilling depths of 80 mm were obtained in a few seconds using a 10 kW laser beam. Moreover pieces of 160 mm were cut at 0.01 meters per minute. Results with carbon steel indicated maximum thicknesses of 110 mm, cut at 0.01 meters per minute with 10 kW, depths about 20% lower were obtained with the AISI 304 stainless steel. A parallel investigation was aimed at characterizing particulate emission during the laser cutting process. At the end of the research it was possible to elaborate a preliminary proposal concerning a laser based dismantling system for the application to a typical Nuclear Power Station. (author)

Cutting agents for special metals

International Nuclear Information System (INIS)

Sugito, Seiji; Sakakibara, Fumi

1979-01-01

The quantity of use of special metals has increased year after year in the Plasma Research Institute, Nagoya University, with the development of researches on plasma and nuclear fusion. Most of these special metals are hard to cut, and in order to secure the surface smoothness and dimensional accuracy, considerable efforts are required. The method of experiment is as follows: cutting agents salt water and acetone, rape-seed oil, sulfide and chloride oil and water soluble cutting oil W grade 3; metals to be cut niobium, molybdenum, tantalum, titanium and tungsten; cutting conditions cutting speed 4.7 to 90 m/min, feed 0.07 to 0.2 mm/rev, depth of cut 0.1 to 0.4 mm, tool cemented carbide bit. Chemicals such as tetrachloromethane and trichloroethane give excellent cutting performance, but the toxicity is intense and the stimulative odor exists, accordingly they are hard to use practically. Cutting was easier when the salt water added with acetone was used than the case of rape-seed oil, but salt water is corrosive. Recently, the machining of molybdenum has been often carried out, and the water soluble cutting oil was the best. It is also good for cutting stainless steel, and its lubricating property is improved by adding some additives such as sulfur, chlorine, phosphorus and molybdenum disulfide. However after cutting with it, washing is required. (Kako, I.)

Performance Testing of Cutting Fluids

DEFF Research Database (Denmark)

Belluco, Walter

The importance of cutting fluid performance testing has increased with documentation requirements of new cutting fluid formulations based on more sustainable products, as well as cutting with minimum quantity of lubrication and dry cutting. Two sub-problems have to be solved: i) which machining...... tests feature repeatability, reproducibility and sensitivity to cutting fluids, and ii) to what extent results of one test ensure relevance to a wider set of machining situations. The present work is aimed at assessing the range of validity of the different testing methods, investigating correlation...... within the whole range of operations, materials, cutting fluids, operating conditions, etc. Cutting fluid performance was evaluated in turning, drilling, reaming and tapping, and with respect to tool life, cutting forces, chip formation and product quality (dimensional accuracy and surface integrity...

Female genital cutting.

Science.gov (United States)

Perron, Liette; Senikas, Vyta; Burnett, Margaret; Davis, Victoria

2013-11-01

To strengthen the national framework for care of adolescents and women affected by female genital cutting (FGC) in Canada by providing health care professionals with: (1) information intended to strengthen their knowledge and understanding of the practice; (2) directions with regard to the legal issues related to the practice; (3) clinical guidelines for the management of obstetric and gynaecological care, including FGC related complications; and (4) guidance on the provision of culturally competent care to adolescents and women with FGC. Published literature was retrieved through searches of PubMed, CINAHL, and The Cochrane Library in September 2010 using appropriate controlled vocabulary (e.g., Circumcision, Female) and keywords (e.g., female genital mutilation, clitoridectomy, infibulation). We also searched Social Science Abstracts, Sociological Abstracts, Gender Studies Database, and ProQuest Dissertations and Theses in 2010 and 2011. There were no date or language restrictions. Searches were updated on a regular basis and incorporated in the guideline to December 2011. Grey (unpublished) literature was identified through searching the websites of health technology assessment and health technology-related agencies, clinical practice guideline collections, clinical trial registries, and national and international medical specialty societies. The quality of evidence in this document was rated using the criteria described in the Report of the Canadian Task Force on Preventive Health Care (Table 1). Summary Statements 1. Female genital cutting is internationally recognized as a harmful practice and a violation of girls' and women's rights to life, physical integrity, and health. (II-3) 2. The immediate and long-term health risks and complications of female genital cutting can be serious and life threatening. (II-3) 3. Female genital cutting continues to be practised in many countries, particularly in sub-Saharan Africa, Egypt, and Sudan. (II-3) 4. Global migration

Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal cutting methods

International Nuclear Information System (INIS)

Bienia, H.; Klotz, B.

2008-01-01

This article describes 3 thermal cutting technologies that are effectively used in nuclear decommissioning projects: the autonomous flame cutting, the plasma arc cutting and the contact arc metal cutting. The autonomous flame cutting technology is based on a high pressure oxygen jet oxidizing the material in a small kerf. Not all metal types are appropriate for this technology. The plasma arc cutting, in contrast to the previous technology, uses an electronically induced plasma arc to melt a kerf in the material. Inside the plasma arc temperatures up to 30.000 K exist, so in theory, this temperature is sufficient to cut all materials. Contact arc metal cutting is a new thermal cutting technology for under-water cutting works. Here, a carbon blade cuts the components. An electric arc between the cutting blade and component melts a kerf into the material easing the cutting. This technology allows the cutting of complex structures with hollows. The applications in nuclear facility dismantling of these 3 cutting technologies and their limits are reported and their requirements (staff, investment) listed in a table. (A.C.)

Extension without Cut

OpenAIRE

Straßburger , Lutz

2012-01-01

International audience; In proof theory one distinguishes sequent proofs with cut and cut-free sequent proofs, while for proof complexity one distinguishes Frege-systems and extended Frege-systems. In this paper we show how deep inference can provide a uniform treatment for both classifications, such that we can define cut-free systems with extension, which is neither possible with Frege-systems, nor with the sequent calculus. We show that the propositional pigeon-hole principle admits polyno...

Fabrication of polycrystalline diamond refractive X-ray lens by femtosecond laser processing

Energy Technology Data Exchange (ETDEWEB)

Kononenko, T.V.; Ralchenko, V.G.; Ashkinazi, E.E.; Konov, V.I. [General Physics Institute of Russian Academy of Sciences, Moscow (Russian Federation); National Research Nuclear University ' ' MEPhI' ' , Moscow (Russian Federation); Polikarpov, M.; Ershov, P. [Immanuel Kant Baltic Federal University, Functional Nanomaterials, Kaliningrad (Russian Federation); Kuznetsov, S.; Yunkin, V. [Institute of Microelectronics Technology RAS, Chernogolovka, Moscow region (Russian Federation); Snigireva, I. [European Synchrotron Radiation Facility, Grenoble (France)

2016-03-15

X-ray planar compound refractive lenses were fabricated from a polycrystalline diamond plate grown by chemical vapor deposition, by precise through cutting with femtosecond laser pulses. The lens geometry and the surface morphology were investigated with optical and scanning electron microscopy, while the material structure modification was analyzed by Raman spectroscopy. The results of the preliminary lens test at 9.25-keV X-rays are presented. (orig.)

Fabrication of polycrystalline diamond refractive X-ray lens by femtosecond laser processing

International Nuclear Information System (INIS)

Kononenko, T.V.; Ralchenko, V.G.; Ashkinazi, E.E.; Konov, V.I.; Polikarpov, M.; Ershov, P.; Kuznetsov, S.; Yunkin, V.; Snigireva, I.

2016-01-01

X-ray planar compound refractive lenses were fabricated from a polycrystalline diamond plate grown by chemical vapor deposition, by precise through cutting with femtosecond laser pulses. The lens geometry and the surface morphology were investigated with optical and scanning electron microscopy, while the material structure modification was analyzed by Raman spectroscopy. The results of the preliminary lens test at 9.25-keV X-rays are presented. (orig.)

Aerodynamic Interactions During Laser Cutting

Science.gov (United States)

Fieret, J.; Terry, M. J.; Ward, B. A.

1986-11-01

Most laser cutting systems utilise a gas jet to remove molten or vaporised material from the kerf. The speed, economy and quality of the cut can be strongly dependent on the aerodynamic conditions created by the nozzle, workpiece proximity and kerf shape. Adverse conditions can be established that may lead to an unwelcome lack of reproducibility of cut quality. Relatively low gas nozzle pressures can result in supersonic flow in the jet with its associated shock fronts. When the nozzle is placed at conventional distances (1-2mm) above the workpiece, the force exerted by the gas on the workpiece and the cut products (the cutting pressure) can be significantly less than the nozzle pressure. Higher cutting pressures can be achieved by increasing the height of the nozzle above the workpiece, to a more damage resistant zone, provided that the shock structure of the jet is taken into account. Conventional conical nozzles with circular exits can be operated with conditions that will result in cutting pressures up to 3 Bar (g) in the more distant zone. At higher pressures in circular tipped nozzles the cutting pressure in this zone decays to inadequate levels. Investigations of a large number of non-circular nozzle tip shapes have resulted in the selection of a few specific shapes that can provide cutting pressures in excess of 6 Bar(g) at distances of 4 to 7mm from the nozzle tip. Since there is a strong correlation between cutting pressure and the speed and quality of laser cutting, the paper describes the aerodynamic requirements for achieving the above effects and reports the cutting results arising from the different nozzle designs and conditions. The results of the work of other investigators, who report anomalous laser cutting results, will be examined and reviewed in the light of the above work.

Anti-Oxidative and Antibacterial Self-Healing Edible Polyelectrolyte Multilayer Film in Fresh-Cut Fruits.

Science.gov (United States)

Liu, Xuefan; Han, Wei; Zhu, Yanxi; Xuan, Hongyun; Ren, Jiaoyu; Zhang, Jianhao; Ge, Liqin

2018-04-01

The consumption of fresh-cut fruits is limited because of the oxidation browning and pathogenic bacteria's growth on the fruit surface. Besides, crack of the fresh-keeping film may shorten the preservation time of fruit. In this work, polyelectrolyte multilayer (PEM) film was fabricated by layer-by-layer (LBL) electrostatic deposition method. The film was made by carboxy methylcellulose sodium (CMC) and chitosan (CS). The as-prepared PEM film had good anti-oxidative and antibacterial capability. It inhibited the growth of Gram-negative bacteria and the antibacterial rate was more than 95%. The stratified structure and linear increase of the absorbance in the film verified a linear increase of film thickness. The slight scratched film could self-heal rapidly after the stimulation of water whatever the layer number was. Moreover, the film could heal cracks whose width was far bigger than the thickness. The application of PEM film on fresh-cut apples showed that PEM film had good browning, weight loss and metabolic activity inhibition ability. These results showed that the PEM film is a good candidate as edible film in fresh-cut fruits applications.

Cutting system for burnable poison rod

International Nuclear Information System (INIS)

Shiina, Atsushi; Toyama, Norihide; Koshino, Yasuo; Fujii, Toshio

1989-01-01

Burnable poison rods attached to spent fuels are contained in a containing box and transported to a receiving pool. The burnable poison rod-containing box is provisionally situated by the operation to a handling device to a provisional setting rack in a cutting pool and attached to a cutting guide of a cutting device upon cutting. The burnable poison rod is cut only in a cutting pool water and tritium generated upon cutting is dissolved into the cutting pool water. Diffusion of tritium is thus restricted. Further, the cutting pool is isolated by a partition device from the receiving pool during cutting of the burnable poison rod. Accordingly, water in which tritium is dissolved is inhibited from moving to the receiving pool and prevail of tritium contamination can be avoided. (T.M.)

Investigation into rationalization of low decontamination pellet fuel fabrication plant configuration

International Nuclear Information System (INIS)

Maekawa, Kazuhiko; Yoshimura, Tadahiro; Hoshino, Yasushi; Munekata, Hideki; Tamaki, Yoshihisa

2005-02-01

In feasibility studies on commercialized FBR cycle system, a comprehensive system investigation and properties evaluation for candidate FBR cycle systems has been implemented through view point of safety, economics, environmental burden reduction, non-proliferation resistivity, etc. As part of these studies, an investigation into rationalization of low decontamination pellet fuel fabrication plant configuration was carried out. Until last fiscal year, conceptual design studies of the fuel fabrication plant in 200t-HM/y scale were conducted, and system properties data concerning economics and environmental burden reduction of fuel fabrication plant was acquired. In addition to this, 50t-HM/y scale plant was also schematically studied. In this fiscal year, a rationalization study on conceptual design of 50t-HM/y scale plant was conducted with main aim of economic improvement, and the 200t-HM/y scale plant design was revised based on the recent R and D progress. The system properties data concerning economics and environmental burden reduction of fuel fabrication plant was also acquired. In both case of the 50t-HM/y and 200t-HM/y scale plant, it was suggested that the equipment costs were reduced in several percentages because of reduction of maintenance equipments and cut in line number at the pellet fabrication process although granulation process fro denitration converted powder and O/M control process for pellets were added. System properties data for comparative evaluation of candidate fuel fabrication systems was also prepared. (author)

Three-Dimensional Grain Shape-Fabric from Unconsolidated Pyroclastic Density Current Deposits: Implications for Extracting Flow Direction and Insights on Rheology

Science.gov (United States)

Hawkins, T. T.; Brand, B. D.; Sarrochi, D.; Pollock, N.

2016-12-01

One of the greatest challenges volcanologists face is the ability to extrapolate information about eruption dynamics and emplacement conditions from deposits. Pyroclastic density current (PDC) deposits are particularly challenging given the wide range of initial current conditions, (e.g., granular, fluidized, concentrated, dilute), and rapid flow transformations due to interaction with evolving topography. Analysis of particle shape-fabric can be used to determine flow direction, and may help to understand the rheological characteristics of the flows. However, extracting shape-fabric information from outcrop (2D) apparent fabric is limited, especially when outcrop exposure is incomplete or lacks context. To better understand and quantify the complex flow dynamics reflected in PDC deposits, we study the complete shape-fabric data in 3D using oriented samples. In the field, the prospective sample is carved from the unconsolidated deposit in blocks, the dimensions of which depend on the average clast size in the sample. The sample is saturated in situ with a water-based sodium silicate solution, then wrapped in plaster-soaked gauze to form a protective cast. The orientation of the sample is recorded on the block faces. The samples dry for five days and are then extracted in intact blocks. In the lab, the sample is vacuum impregnated with sodium silicate and cured in an oven. The fully lithified sample is first cut along the plan view to identify orientations of the long axes of the grains (flow direction), and then cut in the two plains perpendicular to grain elongation. 3D fabric analysis is performed using high resolution images of the cut-faces using computer assisted image analysis software devoted to shape-fabric analysis. Here we present the results of samples taken from the 18 May 1980 PDC deposit facies, including massive, diffuse-stratified and cross-stratified lapilli tuff. We show a relationship between the strength of iso-orientation of the elongated

Fabrication and characterization of 8.87 THz schottky barrier mixer diodes for mixer

Science.gov (United States)

Wang, Wenjie; Li, Qian; An, Ning; Tong, Xiaodong; Zeng, Jianping

2018-04-01

In this paper we report on the fabrication and characterization of GaAs-based THz schottky barrier mixer diodes. Considering the analyzed results as well as fabrication cost and complexity, a group of trade-off parameters was determined. Electron-beam lithography and air-bridge technique have been used to obtain schottky diodes with a cut off frequency of 8.87 THz. Equivalent values of series resistance, ideal factor and junction capacitance of 10.2 (1) Ω, 1.14 (0.03) and 1.76(0.03) respectively have been measured for 0.7um diameter anode devices by DC and RF measurements. The schottky barrier diodes fabrication process is fully planar and very suitable for integration in THz frequency multiplier and mixer circuits. THz Schottky barrier diodes based on such technology with 2 μm diameter anodes have been tested at 1.6 THz in a sub-harmonic mixer.

Technological development of machine tools using less energy in fiscal 2000. Achievement report on research and development of cutting process replacing electric discharge processing; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Hoden kako wo chikansuru sessaku kakoho no kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

Research and development has been made with an objective to replace the electric discharge processing consuming a large amount of energy and having environmental load, with the cutting process consuming less energy while maintaining the equivalent processing precision. This paper summarizes the achievements in fiscal 2000. Development of cutting tools has made three times or more as many multi-aspect utilization as compared to conventional tools possible by researching the tip shapes. In addition, ultra hard end mill suitable for cutting very hard materials using an ultrasonic cutting head was fabricated on the trial basis, and its cutting capability was verified. In developing the cutting processing heard, a vibration mode possible of cutting with the ultra hard tool was generated, ATC has become possible, and the possibility of cutting hard-to-cut materials was verified. For processing a narrow and deep part, an improved type tool was developed, whereas the practical cutting performance suppressing wear of the blade tip was obtained. To deal with the environment, development and prototype fabrication were performed on a unit having a grease lubricated high-speed main shaft that is considered to be the mainstream in the future. In the operation test at 20,000 min-L, know-how was acquired in relation with the basic performance, manufacture and use of the unit. (NEDO)

Theoretical Models for Orthogonal Cutting

DEFF Research Database (Denmark)

De Chiffre, Leonardo

This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”......This review of simple models for orthogonal cutting was extracted from: “L. De Chiffre: Metal Cutting Mechanics and Applications, D.Sc. Thesis, Technical University of Denmark, 1990.”...

Design of a cryo-cooled artificial channel-cut crystal monochromator for the European XFEL

Energy Technology Data Exchange (ETDEWEB)

Dong, Xiaohao, E-mail: xiaohao.dong@xfel.eu; Sinn, Harald, E-mail: harald.sinn@xfel.eu [European XFEL GmbH, Hamburg, D-22761 (Germany); Shu, Deming, E-mail: shu@aps.anl.gov [Argonne National Laboratory, Argonne, IL 60439, U.S.A (United States)

2016-07-27

An artificial channel-cut crystal monochromator for the hard X-Ray beamlines of SASE 1&2, cryogenically cooled by the so-called pulse tube cooler (cryorefrigerator), is currently under development at the European XFEL ( http://www.xfel.eu/ ). The fabrication is on-going. We present here the crystal optical consideration and the novel cooling configuration, according to the X-Ray FEL pulses proprieties. The mechanical design improvements are pointed out as well to implement such kind of monochromator based on the previous similar design.

Laser circular cutting of Kevlar sheets: Analysis of thermal stress filed and assessment of cutting geometry

Science.gov (United States)

Yilbas, B. S.; Akhtar, S. S.; Karatas, C.

2017-11-01

A Kevlar laminate has negative thermal expansion coefficient, which makes it difficult to machine at room temperaures using the conventional cutting tools. Contararily, laser machining of a Kevlar laminate provides advantages over the conventional methods because of the non-mechanical contact between the cutting tool and the workpiece. In the present study, laser circular cutting of Kevlar laminate is considered. The experiment is carried out to examine and evaluate the cutting sections. Temperature and stress fields formed in the cutting section are simulated in line with the experimental study. The influence of hole diameters on temperature and stress fields are investigated incorporating two different hole diameters. It is found that the Kevlar laminate cutting section is free from large size asperities such as large scale sideways burnings and attachemnt of charred residues. The maximum temperature along the cutting circumference remains higher for the large diameter hole than that of the small diameter hole. Temperature decay is sharp around the cutting section in the region where the cutting terminates. This, in turn, results in high temperature gradients and the thermal strain in the cutting region. von Mises stress remains high in the region where temperature gradients are high. von Mises stress follows similar to the trend of temperature decay around the cutting edges.

A study of estimating cutting depth for multi-pass nanoscale cutting by using atomic force microscopy

International Nuclear Information System (INIS)

Lin, Zone-Ching; Hsu, Ying-Chih

2012-01-01

This paper studies two models for estimating cutting depth of multi-pass nanoscale cutting by using an atomic force microscopy (AFM) probe. One estimates cutting depth for multi-pass nanoscale cutting by using regression equations of nanoscale contact pressure factor (NCP factor) while the other uses equation of specific down force energy (SDFE). This paper proposes taking a diamond-coated probe of AFM as the cutting tool to carry out multi-pass nanoscale cutting experiments on the surface of sapphire substrate. In the process of experimentation, different down forces are set, and the probe shape of AFM is known, then using each down force to multi-pass cutting the sapphire substrate. From the measured experimental data of a central cutting depth of the machining groove by AFM, this paper calculates the specific down force energy of each down force. The experiment results reveal that the specific down force energy of each case of multi-pass nanoscale cutting for different down forces under a probe of AFM is close to a constant value. This paper also compares the nanoscale cutting results from estimating cutting depths for each pass of multi-pass among the experimental results and the calculating results obtained by the two theories models. It is found that the model of specific down force energy can calculate cutting depths for each nanoscale cutting pass by one equation. It is easier to use than the multi-regression equations of the nanoscale contact pressure factor. Besides, the estimations of cutting depth results obtained by the model of specific down force energy are closer to that of the experiment results. It shows that the proposed specific down force energy model in this paper is an acceptable model.

Features in Microfluidic Paper-Based Devices Made by Laser Cutting: How Small Can They Be?

Directory of Open Access Journals (Sweden)

Md. Almostasim Mahmud

2018-05-01

Full Text Available In this paper, we determine the smallest feature size that enables fluid flow in microfluidic paper-based analytical devices (µPADs fabricated by laser cutting. The smallest feature sizes fabricated from five commercially available paper types: Whatman filter paper grade 50 (FP-50, Whatman 3MM Chr chromatography paper (3MM Chr, Whatman 1 Chr chromatography paper (1 Chr, Whatman regenerated cellulose membrane 55 (RC-55 and Amershan Protran 0.45 nitrocellulose membrane (NC, were 139 ± 8 µm, 130 ± 11 µm, 103 ± 12 µm, 45 ± 6 µm, and 24 ± 3 µm, respectively, as determined experimentally by successful fluid flow. We found that the fiber width of the paper correlates with the smallest feature size that has the capacity for fluid flow. We also investigated the flow speed of Allura red dye solution through small-scale channels fabricated from different paper types. We found that the flow speed is significantly slower through microscale features and confirmed the similar trends that were reported previously for millimeter-scale channels, namely that wider channels enable quicker flow speed.

Consumer evaluation of palatability characteristics of a beef value-added cut compared to common retail cuts.

Science.gov (United States)

Lepper-Blilie, A N; Berg, E P; Germolus, A J; Buchanan, D S; Berg, P T

2014-01-01

The objectives of this study were to educate consumers about value-added beef cuts and evaluate their palatability responses of a value cut and three traditional cuts. Three hundred and twenty-two individuals participated in the beef value cut education seminar series presented by trained beef industry educators. Seminar participants evaluated tenderness, juiciness, flavor, and overall like of four samples, bottom round, top sirloin, ribeye, and a value cut (Delmonico or Denver), on a 9-point scale. The ribeye and the value cut were found to be similar in all four attributes and differed from the top sirloin and bottom round. Correlations and regression analysis found that flavor was the largest influencing factor for overall like for the ribeye, value cut, and top sirloin. The value cut is comparable to the ribeye and can be a less expensive replacement. © 2013.

An Ethology of Urban Fabric(s)

DEFF Research Database (Denmark)

Fritsch, Jonas; Thomsen, Bodil Marie Stavning

2014-01-01

The article explores a non-metaphorical understanding of urban fabric(s), shifting the attention from a bird’s eye perspective to the actual, textural manifestations of a variety of urban fabric(s) to be studied in their real, processual, ecological and ethological complexity within urban life. We...... effectuate this move by bringing into resonance a range of intersecting fields that all deal with urban fabric(s) in complementary ways (interaction design and urban design activism, fashion, cultural theory, philosophy, urban computing)....

Flux cutting in superconductors

International Nuclear Information System (INIS)

Campbell, A M

2011-01-01

This paper describes experiments and theories of flux cutting in superconductors. The use of the flux line picture in free space is discussed. In superconductors cutting can either be by means of flux at an angle to other layers of flux, as in longitudinal current experiments, or due to shearing of the vortex lattice as in grain boundaries in YBCO. Experiments on longitudinal currents can be interpreted in terms of flux rings penetrating axial lines. More physical models of flux cutting are discussed but all predict much larger flux cutting forces than are observed. Also, cutting is occurring at angles between vortices of about one millidegree which is hard to explain. The double critical state model and its developments are discussed in relation to experiments on crossed and rotating fields. A new experiment suggested by Clem gives more direct information. It shows that an elliptical yield surface of the critical state works well, but none of the theoretical proposals for determining the direction of E are universally applicable. It appears that, as soon as any flux flow takes place, cutting also occurs. The conclusion is that new theories are required. (perspective)

Cutting force and wear evaluation in peripheral milling by CVD diamond dental tools

International Nuclear Information System (INIS)

Polini, R.; Allegri, A.; Guarino, S.; Quadrini, F.; Sein, H.; Ahmed, W.

2004-01-01

Co-cemented tungsten carbide (WC-Co) tools are currently employed in dental application for prosthesis fabrication. The deposition of a diamond coating onto WC-Co tools could allow both to increase the tool life and tool performance at higher speeds. However, at present it is very difficult to quantify the effective advantage of the application of a diamond coating onto dental tools compared to traditional uncoated tools. Therefore, in this work, we have deposited diamond coatings onto WC-Co dental tools having different geometries by Hot Filament Chemical Vapour Deposition (HFCVD). Prior to deposition, the WC-Co tools were pre-treated in order to roughen the surface and to modify the chemical surface composition. The use of the HFCVD process enabled the deposition of a uniform coating despite the complex geometries of the dental mills. For the first time, in accordance to the knowledge of the authors, we have studied and compared the cutting behaviour of both virgin and diamond-coated dental tools by measuring both wear and cutting force time evolution under milling a very hard Co-Cr-Mo dental alloy. To ensure constant cutting rate (20,000-r.p.m. cutting rate, 0.01-m/min feed rate and 0.5-mm depth of cut), a proper experimental apparatus was used. Three different mill geometries were considered in both coated and uncoated conditions. The results showed that, under the high-speed conditions employed, uncoated tools underwent to catastrophic failure within a few seconds of machining. Diamond-coated tools exhibited much longer tool lives. Lower forces were measured when the coated tool was employed due to the much lower material-mill friction. The best behaviour was observed for coated mills with the presence of a chip-breaker

The marginal fit of selective laser melting-fabricated metal crowns: an in vitro study.

Science.gov (United States)

Xu, Dan; Xiang, Nan; Wei, Bin

2014-12-01

The selective laser melting technique is attracting interest in prosthetic dentistry. The marginal fit is a key criterion for fixed restorations. The purpose of the study was to evaluate the marginal fit of cast cobalt-chromium alloy crowns versus the fit of selective laser melting-fabricated crowns. The marginal gap widths of 36 single crowns (18 selective laser melting-fabricated cobalt-chromium metal crowns and 18 cobalt-chromium cast crowns) were determined with a silicone replica technique. Each crown specimen was cut into 4 sections, and the marginal gap width of each cross section was evaluated by stereomicroscopy (× 100). The Student t test was used to evaluate whether significant differences occurred in the marginal gap widths between the selective laser melting-fabricated and cast cobalt-chromium metal crowns (α=.05). The mean marginal gap width of the cast crowns (170.19 μm) was significantly wider than that of the selective laser melting-fabricated crowns (102.86 μm). Selective laser melting-fabricate cobalt-chromium dental crowns found improved marginal gap widths compared with traditional cast crowns. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Development of underwater laser cutting technology

International Nuclear Information System (INIS)

Sato, Seiichi; Inaba, Takanori; Inose, Koutarou; Matsumoto, Naoyuki; Sakakibara, Yuji

2015-01-01

In is desirable to use remote underwater device for the decommissioning work of highly radioactive components such as the nuclear internals from a view point of reducing the ranitidine exposure to the worker. Underwater laser cutting technology has advantages. First advantage in underwater laser cutting technology is that low reaction force during cutting, namely, remote operability is superior. Second point is that underwater laser cutting generates a little amount of secondary waste, because cutting kerf size is very small. Third point is that underwater laser cutting has low risk of the process delay, because device trouble is hard to happen. While underwater laser cutting has many advantages, the careful consideration in the safe treatment of the offgas which underwater laser cutting generates is necessary. This paper describes outline of underwater laser cutting technology developed by IHI Corporation (IHI) and that this technology is effective in various dismantling works in water. (author)

Cutting temperature measurement and material machinability

Directory of Open Access Journals (Sweden)

Nedić Bogdan P.

2014-01-01

Full Text Available Cutting temperature is very important parameter of cutting process. Around 90% of heat generated during cutting process is then away by sawdust, and the rest is transferred to the tool and workpiece. In this research cutting temperature was measured with artificial thermocouples and question of investigation of metal machinability from aspect of cutting temperature was analyzed. For investigation of material machinability during turning artificial thermocouple was placed just below the cutting top of insert, and for drilling thermocouples were placed through screw holes on the face surface. In this way was obtained simple, reliable, economic and accurate method for investigation of cutting machinability.

Stresses in ultrasonically assisted bone cutting

International Nuclear Information System (INIS)

Alam, K; Mitrofanov, A V; Silberschmidt, V V; Baeker, M

2009-01-01

Bone cutting is a frequently used procedure in the orthopaedic surgery. Modern cutting techniques, such as ultrasonic assisted drilling, enable surgeons to perform precision operations in facial and spinal surgeries. Advanced understanding of the mechanics of bone cutting assisted by ultrasonic vibration is required to minimise bone fractures and to optimise the technique performance. The paper presents results of finite element simulations on ultrasonic and conventional bone cutting analysing the effects of ultrasonic vibration on cutting forces and stress distribution. The developed model is used to study the effects of cutting and vibration parameters (e.g. amplitude and frequency) on the stress distributions in the cutting region.

Optimisation Of Cutting Parameters Of Composite Material Laser Cutting Process By Taguchi Method

Science.gov (United States)

Lokesh, S.; Niresh, J.; Neelakrishnan, S.; Rahul, S. P. Deepak

2018-03-01

The aim of this work is to develop a laser cutting process model that can predict the relationship between the process input parameters and resultant surface roughness, kerf width characteristics. The research conduct is based on the Design of Experiment (DOE) analysis. Response Surface Methodology (RSM) is used in this work. It is one of the most practical and most effective techniques to develop a process model. Even though RSM has been used for the optimization of the laser process, this research investigates laser cutting of materials like Composite wood (veneer)to be best circumstances of laser cutting using RSM process. The input parameters evaluated are focal length, power supply and cutting speed, the output responses being kerf width, surface roughness, temperature. To efficiently optimize and customize the kerf width and surface roughness characteristics, a machine laser cutting process model using Taguchi L9 orthogonal methodology was proposed.

Selection of Near Optimal Laser Cutting Parameters in CO2 Laser Cutting by the Taguchi Method

Directory of Open Access Journals (Sweden)

Miloš MADIĆ

2013-12-01

Full Text Available Identification of laser cutting conditions that are insensitive to parameter variations and noise is of great importance. This paper demonstrates the application of Taguchi method for optimization of surface roughness in CO2 laser cutting of stainless steel. The laser cutting experiment was planned and conducted according to the Taguchi’s experimental design using the L27 orthogonal array. Four laser cutting parameters such as laser power, cutting speed, assist gas pressure, and focus position were considered in the experiment. Using the analysis of means and analysis of variance, the significant laser cutting parameters were identified, and subsequently the optimal combination of laser cutting parameter levels was determined. The results showed that the cutting speed is the most significant parameter affecting the surface roughness whereas the influence of the assist gas pressure can be neglected. It was observed, however, that interaction effects have predominant influence over the main effects on the surface roughness.

How Can I Stop Cutting?

Science.gov (United States)

... Educators Search English Español How Can I Stop Cutting? KidsHealth / For Teens / How Can I Stop Cutting? ... in a soft, cozy blanket Substitutes for the Cutting Sensation You'll notice that all the tips ...

Rooting of stem cuttings of ixora

Directory of Open Access Journals (Sweden)

Aline De Souza Silva

2015-08-01

Full Text Available The ixora is ornamental plant widely used in landscaping. In order to maximize the propagation of cuts, we evaluated the concentrations of auxin (indolbutiric acid and the presence of leaves on the rooting in cuts of Ixora coccinea L. The experiment was conducted in randomized block design, in factorial design 3x4, with three types of cuts (without leaf, with two or four leaves, four concentrations of indolbutiric acid (0, 1000, 2000 and 4000 mg L-1, with four replications and 10 cuts in each experimental unit. After 53 days of implantation the experiment, evaluated the survival(%, rooting(%, sprouting(%, formation of callus(%, number, length and biomass of roots formed. The interaction of the type of cuts with concentrations of auxin was not significant for any of the variables analyzed. The survival of cuttings was not influenced by the treatments. Cuts with two or four leaves presented rooting and length of roots above the cuttings without leaves. The application of auxin does not substitute the presence of leaf in cuts of ixora in vegetative propagation. The vegetative propagation by cut of ixora can be made without application of auxin, and the leaves must be maintained in the cuttings.

Ultrafast Optical Modulation of Second- and Third-Harmonic Generation from Cut-Disk-Based Metasurfaces

KAUST Repository

Sartorello, Giovanni

2016-06-06

We design and fabricate a metasurface composed of gold cut-disk resonators that exhibits a strong coherent nonlinear response. We experimentally demonstrate all-optical modulation of both second- and third-harmonic signals on a subpicosecond time scale. Pump-probe experiments and numerical models show that the observed effects are due to the ultrafast response of the electronic excitations in the metal under external illumination. These effects pave the way for the development of novel active nonlinear metasurfaces with controllable and switchable coherent nonlinear response. © 2016 American Chemical Society.

Paper-based microfluidics with high resolution, cut on a glass fiber membrane for bioassays.

Science.gov (United States)

Fang, Xueen; Wei, Shasha; Kong, Jilie

2014-03-07

In this report, we describe a simple, low-cost, straight forward and highly reproducible fabrication method of microfluidic systems. This system was cut on a glass fiber membrane by a common cutter without using any other sophisticated equipment or organic solvents. This format represents a novel type of paper-based microfluidics with high resolution of the microchannel down to ~137 μm, comparable to those made by conventional photolithography. We successfully applied this method to microfluidics to create a star micro-array format of multiplexed urine tests in this study.

Development of lathe tool dynamometer and finding cutting forces using negative and positive rake angle cutting tool

International Nuclear Information System (INIS)

Zeb, M.A.; Irfan, M.A.

2005-01-01

Most output parameters in machining, such as cutting forces, temperatures, strains and the work-hardening of the chip material, are directly related to the chip formation process. The characteristics of machining processes can be well understood if the forces and strains during chip formation are known. In this research a lathe tool dynamometer was used to measure cutting forces involved in machining of Steel 1045 and Aluminum 2219 T62. High Speed Steel (HSS), cutting tools with positive and negative rake angles were used. It was observed that more cutting forces are experienced by the cutting tool with positive rake angle as compared to the forces experienced by the cutting tool with negative rake angle. For steel 1045 the cutting forces using positive rake angle cutting tool were much higher. This suggested that for harder materials using a negative rake angle is more suitable for cutting. (author)

Fabrication and characterization of n-AlGaAs/ GaAs Schottky diode for rectennas device application

International Nuclear Information System (INIS)

Norfarariyanti Parimon; Abdul Manaf Hashim; Farahiyah Mustafa

2009-01-01

Full text: Schottky diode was designed and fabricated on n-AlGaAs/GaAs high electron mobility transistor (HEMT) structure for rectennas device application. Rectennas is one of the most potential devices to form the wireless power supply which is really good at converting microwaves to DC. The processing steps used in the fabrication of Schottky diode were the conventional steps used in standard GaAs processing. Current?voltage (I-V) measurements showed that the device had rectifying properties with a barrier height of 0.5468 eV for Ni/Au metallization. The fabricated Schottky diode detected RF signals and the cut-off frequency up to 20 GHz was estimated in direct injection experiments. These preliminary results will provide a breakthrough for the direct integration with antenna towards realization of rectennas device application. (author)

Fabrication and Characterization of n-AlGaAs/GaAs Schottky Diode for Rectenna Device Application

Energy Technology Data Exchange (ETDEWEB)

Parimon, Norfarariyanti; Mustafa, Farahiyah; Hashim, Abdul Manaf; Rahman, Shaharin Fadzli Abd; Rahman, Abdul Rahim Abdul [Material Innovations and Nanoelectronics Research Group, Faculty of Electrical Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia); Osman, Mohd Nizam, E-mail: manaf@fke.utm.my [Telekom Research and Development, TM Innovation Centre, 63000 Cyberjaya (Malaysia)

2011-02-15

Schottky diode was designed and fabricated on n-AlGaAs/GaAs high electron mobility transistor (HEMT) structure for rectenna device application. Rectenna is one of the most potential devices to form the wireless power supply which is really good at converting microwaves to DC. The processing steps used in the fabrication of Schottky diode were the conventional steps used in standard GaAs processing. Current-voltage (I-V) measurements showed that the device had rectifying properties with a barrier height of 0.5468 eV for Ni/Au metallization. The fabricated Schottky diode detected RF signals and the cut-off frequency up to 20 GHz was estimated in direct injection experiments. These preliminary results will provide a breakthrough for the direct integration with antenna towards realization of rectenna device application.

Fabrication and Characterization of n-AlGaAs/GaAs Schottky Diode for Rectenna Device Application

International Nuclear Information System (INIS)

Parimon, Norfarariyanti; Mustafa, Farahiyah; Hashim, Abdul Manaf; Rahman, Shaharin Fadzli Abd; Rahman, Abdul Rahim Abdul; Osman, Mohd Nizam

2011-01-01

Schottky diode was designed and fabricated on n-AlGaAs/GaAs high electron mobility transistor (HEMT) structure for rectenna device application. Rectenna is one of the most potential devices to form the wireless power supply which is really good at converting microwaves to DC. The processing steps used in the fabrication of Schottky diode were the conventional steps used in standard GaAs processing. Current-voltage (I-V) measurements showed that the device had rectifying properties with a barrier height of 0.5468 eV for Ni/Au metallization. The fabricated Schottky diode detected RF signals and the cut-off frequency up to 20 GHz was estimated in direct injection experiments. These preliminary results will provide a breakthrough for the direct integration with antenna towards realization of rectenna device application.

Mechanical properties of weft knitted fabric reinforced composites. Iamimono kyoka fukugo zairyo no rikigakuteki tokusei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Wu, W.; Inoda, M.; Kotaki, M.; Goto, A.; Fujita, A.; Hamada, H.; Maekawa, Z. (Kyoto Institute of Technology, Kyoto (Japan). Faculty of Textile Science)

1993-09-15

Mechanical properties and failure behavior of weft knitted fabric reinforced composites were studied. Aramid fiber was used as reinforcement (knitting fiber), and epoxy resin as matrix. Different tensions were applied to the weft knitted fabric in a course or wale direction to prepare 5 kinds of fiber reinforced composites with different densities of the knitted fabric, and tensile test pieces were thus provided by cutting each composite in a course or wale direction. As a result, the weft knitted fabric reinforced composite offered a dynamical anisotropy, and the tensile strength of the test pieces was higher in wale direction than course one. Fracture in a course direction occurred at the section with extreme low fiber content, while fracture in a wale direction occurred at a loop interlocking region due to stress concentration. The tensile strength was constant or increased in a course or wale direction by stretching the knitted fabric before molding, respectively. 21 refs., 15 figs., 2 tabs.

Investigation of Physical Phenomena and Cutting Efficiency for Laser Cutting on Anode for Li-Ion Batteries

Directory of Open Access Journals (Sweden)

Dongkyoung Lee

2018-02-01

Full Text Available Lithium-ion batteries have a higher energy density than other secondary batteries. Among the lithium-ion battery manufacturing process, electrode cutting is one of the most important processes since poor cut quality leads to performance degradation, separator protrusion, and local electric stress concentration. This may, eventually, lead to malfunction of lithium-ion batteries or explosion. The current mechanical cutting technology uses a contact process and this may lead to process instability. Furthermore, there are additional costs if the tools and cell design are changed. To solve these issues, laser cutting has been used. Conventional dependent parameters have limitations in investigating and explaining many physical phenomena during the laser cutting of electrodes. Therefore, this study proposes specific widths such as melting, top, and kerf width. Moreover, the relationship between laser parameters and multiphysical phenomena with the proposed widths are investigated. Five types of classification with regard to physical phenomena are presented and explained with SEM images. Cutting efficiency is estimated with the proposed widths. The proposed specific cutting widths, five types of geometrical classification, and cutting efficiency can be used as standardized parameters to evaluate the cutting quality.

CALCULATION OF LASER CUTTING COSTS

OpenAIRE

Bogdan Nedic; Milan Eric; Marijana Aleksijevic

2016-01-01

The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, compar...

Early Tertiary magmatism and probable Mesozoic fabrics in the Black Mountains, Death Valley, California

Science.gov (United States)

Miller, Martin G.; Friedman, Richard M.

1999-01-01

We report two early Tertiary U-Pb zircon ages for pegmatite from the Black Mountains of Death Valley, California. These ages, 54.7 ± 0.6 Ma and 56 ± 3 Ma, are unique for much of southeastern California. The samples belong to a pegmatite suite that occupies part of the footwall of the Badwater turtleback, a late Tertiary extensional feature; similar but undated pegmatite intrudes the footwalls of the Copper Canyon and Mormon Point turtlebacks farther south. The pegmatite suite demonstrates that fabric development on the turtlebacks was at least a two-stage process. Fabrics cut by these pegmatites likely formed during the Mesozoic, whereas those that involve them formed during late Tertiary extension.

Crude oil water-cut sensing with disposable laser ablated and inkjet printed RF microfluidics

KAUST Repository

McKerricher, Garret

2014-06-01

This paper presents the first microwave microfluidic crude oil/water cut sensor. Anhydrous crude oil is been tested and the device provides a measurable frequency shift of 500MHz at 50% (vol.) water content and a 50MHz shift for a 5% (vol.) water concentration. The sensor is realized with a low-cost direct write fabrication method. This involves laser ablation, inkjet printing, laser heating, along with low temperature thermal compression bonding of Poly (methylmethacrylate) (PMMA) sheets. By using localized laser sintering a conductivity of 2.5e6 S/m is achieved for silver nanoparticle ink without the need to heat the entire substrate above its glass transition temperature of (105 °C). The dielectric properties of PMMA are characterized to 1 GHz and a simulation model is offered for analyzing the dielectric properties of crude oil. This work demonstrates that a small form factor and low cost device is capable of precise water-cut measurements. © 2014 IEEE.

Crude oil water-cut sensing with disposable laser ablated and inkjet printed RF microfluidics

KAUST Repository

McKerricher, Garret; Conchouso Gonzalez, David; Cook, Benajmin S.; Foulds, Ian G.; Shamim, Atif

2014-01-01

This paper presents the first microwave microfluidic crude oil/water cut sensor. Anhydrous crude oil is been tested and the device provides a measurable frequency shift of 500MHz at 50% (vol.) water content and a 50MHz shift for a 5% (vol.) water concentration. The sensor is realized with a low-cost direct write fabrication method. This involves laser ablation, inkjet printing, laser heating, along with low temperature thermal compression bonding of Poly (methylmethacrylate) (PMMA) sheets. By using localized laser sintering a conductivity of 2.5e6 S/m is achieved for silver nanoparticle ink without the need to heat the entire substrate above its glass transition temperature of (105 °C). The dielectric properties of PMMA are characterized to 1 GHz and a simulation model is offered for analyzing the dielectric properties of crude oil. This work demonstrates that a small form factor and low cost device is capable of precise water-cut measurements. © 2014 IEEE.

Method of cutting radioactivated metal structures

International Nuclear Information System (INIS)

Takimoto, Yoshinori; Sakota, Kotaro; Hamamoto, Noboru; Harada, Keizo.

1985-01-01

Purpose: To improve the cutting performance to a level as comparable with that in air, as well as prevent the scattering of the radioactive materials upon cutting to the level as that in water cutting. Method: After igniting a gas cutting torch automatically, water spray by the local water sprayer is started by the actuation of a submerged pump, while a gas cutting manipulator is operated to cut the nuclear reactor pressure vessel. In this way, cutting exhaust gases resulted from the gas cutting torch are water-washed by the spray from the local water sprayer and falls within the nuclear rector pressure vessel in the form of water streams or droplets along the inner wall surface of the pressure vessel. Further, water is fed again to the local water sprayer by the submerged pump. (Kawakami, Y.)

Laser Cutting of Thin Nickel Bellows

Science.gov (United States)

Butler, C. L.

1986-01-01

Laser cutting technique produces narrow, precise, fast, and repeatable cuts in thin nickel-allow bellows material. Laser cutting operation uses intense focused beam to melt material and assisting gas to force melted material through part thickness, creating void. When part rotated or moved longitudinally, melting and material removal continuous and creates narrow, fast, precise, and repeatable cut. Technique used to produce cuts of specified depths less than material thickness. Avoids distortion, dents, and nicks produced in delicate materials during lathe trimming operations, which require high cutting-tool pressure and holding-fixture forces.

Experimental improvement of the technology of cutting of high-pressure hoses with metal braid on hand cutting machine

OpenAIRE

Karpenko, Mykola; Bogdevicius, Marijonas; Prentkovskis, Olegas

2016-01-01

In the article the review of the problem of improvement of technology of high pressure hoses cutting on the hand cutting machines is analyzed. Different methods of cutting of high pressure hoses into the billets are overviewed and the quality of edge cuts of hoses is analyzed. The comparison of treatment on automatic cutting machines and on hand cutting machines is carried out. Different experimental techniques of improvement of the quality of edges cutting of high pressure hoses are prese...

Status report, canister fabrication

International Nuclear Information System (INIS)

Andersson, Claes-Goeran; Eriksson, Peter; Westman, Marika; Emilsson, Goeran

2004-06-01

The report gives an account of the development of material and fabrication technology for copper canisters with cast inserts during the period from 2000 until the start of 2004. The engineering design of the canister and the choice of materials in the constituent components described in previous status reports have not been significantly changed. In the reference canister, the thickness of the copper shell is 50 mm. Fabrication of individual components with a thinner copper thickness is done for the purpose of gaining experience and evaluating fabrication and inspection methods for such canisters. As a part of the development of cast inserts, computer simulations of the casting processes and techniques used at the foundries have been performed for the purpose of optimizing the material properties. These properties have been evaluated by extensive tensile testing and metallographic inspection of test material taken from discs cut at different points along the length of the inserts. The testing results exhibit a relatively large spread. Low elongation values in certain tensile test specimens are due to the presence of poorly formed graphite, porosities, slag or other casting defects. It is concluded in the report that it will not be possible to avoid some presence of observed defects in castings of this size. In the deep repository, the inserts will be exposed to compressive loading and the observed defects are not critical for strength. An analysis of the strength of the inserts and formulation of relevant material requirements must be based on a statistical approach with probabilistic calculations. This work has been initiated and will be concluded during 2004. An initial verifying compression test of a canister in an isostatic press has indicated considerable overstrength in the structure. Seamless copper tubes are fabricated by means of three methods: extrusion, pierce and draw processing, and forging. It can be concluded that extrusion tests have revealed a

Status report, canister fabrication

Energy Technology Data Exchange (ETDEWEB)

Andersson, Claes-Goeran; Eriksson, Peter; Westman, Marika [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Emilsson, Goeran [CSM Materialteknik AB, Linkoeping (Sweden)

2004-06-01

The report gives an account of the development of material and fabrication technology for copper canisters with cast inserts during the period from 2000 until the start of 2004. The engineering design of the canister and the choice of materials in the constituent components described in previous status reports have not been significantly changed. In the reference canister, the thickness of the copper shell is 50 mm. Fabrication of individual components with a thinner copper thickness is done for the purpose of gaining experience and evaluating fabrication and inspection methods for such canisters. As a part of the development of cast inserts, computer simulations of the casting processes and techniques used at the foundries have been performed for the purpose of optimizing the material properties. These properties have been evaluated by extensive tensile testing and metallographic inspection of test material taken from discs cut at different points along the length of the inserts. The testing results exhibit a relatively large spread. Low elongation values in certain tensile test specimens are due to the presence of poorly formed graphite, porosities, slag or other casting defects. It is concluded in the report that it will not be possible to avoid some presence of observed defects in castings of this size. In the deep repository, the inserts will be exposed to compressive loading and the observed defects are not critical for strength. An analysis of the strength of the inserts and formulation of relevant material requirements must be based on a statistical approach with probabilistic calculations. This work has been initiated and will be concluded during 2004. An initial verifying compression test of a canister in an isostatic press has indicated considerable overstrength in the structure. Seamless copper tubes are fabricated by means of three methods: extrusion, pierce and draw processing, and forging. It can be concluded that extrusion tests have revealed a

Diluted melt proton exchange slab waveguides in LiNbO3: A new fabrication and characterization method

DEFF Research Database (Denmark)

Veng, Torben; Skettrup, Torben

1997-01-01

A method of dilute-melt proton exchange employing a mixture of glycerol and KHSO4 with lithium benzoate added is used to fabricate planar waveguides in c-cut LiNbO3. With this exchange melt system the waveguide refractive index profiles can be fabricated with a high degree of reproducibility...... the waveguide refractive index profile from the measured mode indices is introduced. The main advantage of this characterization method compared with other methods is that it also applies to single-mode waveguides. Using the new characterization method we investigate in detail the relation between waveguide...

Laser cutting of various materials: Kerf width size analysis and life cycle assessment of cutting process

Science.gov (United States)

Yilbas, Bekir Sami; Shaukat, Mian Mobeen; Ashraf, Farhan

2017-08-01

Laser cutting of various materials including Ti-6Al-4V alloy, steel 304, Inconel 625, and alumina is carried out to assess the kerf width size variation along the cut section. The life cycle assessment is carried out to determine the environmental impact of the laser cutting in terms of the material waste during the cutting process. The kerf width size is formulated and predicted using the lump parameter analysis and it is measured from the experiments. The influence of laser output power and laser cutting speed on the kerf width size variation is analyzed using the analytical tools including scanning electron and optical microscopes. In the experiments, high pressure nitrogen assisting gas is used to prevent oxidation reactions in the cutting section. It is found that the kerf width size predicted from the lump parameter analysis agrees well with the experimental data. The kerf width size variation increases with increasing laser output power. However, this behavior reverses with increasing laser cutting speed. The life cycle assessment reveals that material selection for laser cutting is critical for the environmental protection point of view. Inconel 625 contributes the most to the environmental damages; however, recycling of the waste of the laser cutting reduces this contribution.

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Troy Reed; Ergun Kuru

2004-09-30

The Advanced Cuttings Transport Study (ACTS) was a 5-year JIP project undertaken at the University of Tulsa (TU). The project was sponsored by the U.S. Department of Energy (DOE) and JIP member companies. The objectives of the project were: (1) to develop and construct a new research facility that would allow three-phase (gas, liquid and cuttings) flow experiments under ambient and EPET (elevated pressure and temperature) conditions, and at different angle of inclinations and drill pipe rotation speeds; (2) to conduct experiments and develop a data base for the industry and academia; and (3) to develop mechanistic models for optimization of drilling hydraulics and cuttings transport. This project consisted of research studies, flow loop construction and instrumentation development. Following a one-year period for basic flow loop construction, a proposal was submitted by TU to the DOE for a five-year project that was organized in such a manner as to provide a logical progression of research experiments as well as additions to the basic flow loop. The flow loop additions and improvements included: (1) elevated temperature capability; (2) two-phase (gas and liquid, foam etc.) capability; (3) cuttings injection and removal system; (4) drill pipe rotation system; and (5) drilling section elevation system. In parallel with the flow loop construction, hydraulics and cuttings transport studies were preformed using drilling foams and aerated muds. In addition, hydraulics and rheology of synthetic drilling fluids were investigated. The studies were performed under ambient and EPET conditions. The effects of temperature and pressure on the hydraulics and cuttings transport were investigated. Mechanistic models were developed to predict frictional pressure loss and cuttings transport in horizontal and near-horizontal configurations. Model predictions were compared with the measured data. Predominantly, model predictions show satisfactory agreements with the measured data. As a

The Differences in Chemical Composition, Physical Quality Traits and Nutritional Values of Horse Meat as Affected by Various Retail Cut Types

Directory of Open Access Journals (Sweden)

Pil Nam Seong

2016-01-01

Full Text Available The effects of retail cut type on chemical, quality and nutritional characteristics of horse meat were studied. Jeju female breed horses (n = 9 at 32-mo-old were slaughtered and the carcasses at 24 h post-mortem were fabricated into 10 retail cuts including: tender-loin, loin, strip-loin, shoulder-chuck-roll, shoulder-clod, top-round, outside-round, brisket, short-plate-brisket, and shank. The results revealed that all of parameters (chemical, meat quality and nutritional composition examined significantly (p<0.05 differed between the cuts. The chemical composition range (minimum to maximum of cuts was found as such: moisture 65.06% to 71.69%; protein 19.07% to 21.28%; collagen 1.40% to 2.45%; fat 2.56% to 12.14% and cholesterol 55.76 to 79.50 mg/100 g. Shoulder-chuck-roll had the highest pH and water-holding capacity, while top-round had the highest cooking loss. Shear force ranged between the cuts from 2.80 kg/cm2 to 4.98 kg/cm2. The Cu, Fe, and Zn contents ranged between the cuts from 1.52 mg/kg to 2.75 mg/kg, 21.25 mg/kg to 30.85 mg/kg, and 16.51 mg/kg to 40.42 mg/kg, respectively. Additionally, most of the cuts studied showed favorable polyunsaturated fatty acid/saturated fatty acid, n-3/n-6 and essential amino acid/non-essential amino acid ratios.

The Differences in Chemical Composition, Physical Quality Traits and Nutritional Values of Horse Meat as Affected by Various Retail Cut Types.

Science.gov (United States)

Seong, Pil Nam; Park, Kyoung Mi; Kang, Geun Ho; Cho, Soo Hyun; Park, Beom Young; Chae, Hyun Seok; Van Ba, Hoa

2016-01-01

The effects of retail cut type on chemical, quality and nutritional characteristics of horse meat were studied. Jeju female breed horses (n = 9) at 32-mo-old were slaughtered and the carcasses at 24 h post-mortem were fabricated into 10 retail cuts including: tender-loin, loin, strip-loin, shoulder-chuck-roll, shoulder-clod, top-round, outside-round, brisket, short-plate-brisket, and shank. The results revealed that all of parameters (chemical, meat quality and nutritional composition) examined significantly (p<0.05) differed between the cuts. The chemical composition range (minimum to maximum) of cuts was found as such: moisture 65.06% to 71.69%; protein 19.07% to 21.28%; collagen 1.40% to 2.45%; fat 2.56% to 12.14% and cholesterol 55.76 to 79.50 mg/100 g. Shoulder-chuck-roll had the highest pH and water-holding capacity, while top-round had the highest cooking loss. Shear force ranged between the cuts from 2.80 kg/cm(2) to 4.98 kg/cm(2). The Cu, Fe, and Zn contents ranged between the cuts from 1.52 mg/kg to 2.75 mg/kg, 21.25 mg/kg to 30.85 mg/kg, and 16.51 mg/kg to 40.42 mg/kg, respectively. Additionally, most of the cuts studied showed favorable polyunsaturated fatty acid/saturated fatty acid, n-3/n-6 and essential amino acid/non-essential amino acid ratios.

Practical side of cutting. Part 3. ; CO2 laser cutting. Setsudan gijutsu no jissai. 3. ; Laser setsudan

Energy Technology Data Exchange (ETDEWEB)

Miyazaki, T.; Shinonaga, H. (Toshiba Corp., Tokyo (Japan))

1993-03-05

The nature peculiar to laser beam makes it difficult to understand the phenomena in laser cutting. Quoting an example of cutting steel materials, practical minimum basic subjects, factors governing the cutting phenomena with points to be considered, and the current state of the technology are outlined. Various kinds of expert systems and automatic programming devices have been placed on the market to make NC input easier in laser cutting. Shape accuracy, cutting quality, cutting speed, applicable plate thickness, etc. are among the subjects required for laser cutting. The factors are the method of scanning, characteristics of laser beam, work, machining conditions, etc. The factors obstructing stable processing are the change in the ambient temperature, humidity, dust, oil mist, vibration, etc. The basic factors which control the laser cutting are the power density and its distribution at the working point. Pulse cutting is employed when continuous laser heat input is not appropriate. Summarized report is made on the focal point and assist gas. 16 refs., 9 figs., 1 tab.

Cutting Cosmos

DEFF Research Database (Denmark)

Mikkelsen, Henrik Hvenegaard

For the first time in over 30 years, a new ethnographic study emerges on the Bugkalot tribe, more widely known as the Ilongot of the northern Philippines. Exploring the notion of masculinity among the Bugkalot, Cutting Cosmos is not only an experimental, anthropological study of the paradoxes...... around which Bugkalot society revolves, but also a reflection on anthropological theory and writing. Focusing on the transgressive acts through which masculinity is performed, this book explores the idea of the cosmic cut, the ritual act that enables the Bugkalot man to momentarily hold still the chaotic...

Laser Fenestration of Aortic Stent-Grafts Followed by Noncompliant vs Cutting Balloon Dilation: A Scanning Electron Microscopy Study.

Science.gov (United States)

Lin, Jing; Parikh, Niraj; Udgiri, Naval; Wang, Shaoxia; Miller, Daniel F; Li, Chaojing; Panneton, Jean; Nutley, Mark; Zhang, Ze; Huang, Yunfan; Lu, Jun; Zhang, Jingyi; Wang, Lu; Guidoin, Robert

2018-06-01

To examine the effects of in situ laser fenestration and subsequent balloon dilation (noncompliant vs cutting) on the graft fabric of 4 aortic stent-graft models. In an in vitro setup, the Zenith TX2, Talent, Endurant, and Anaconda aortic stent-grafts (all made of polyester graft material) were subjected to laser fenestration with a 2.3-mm-diameter probe at low and high energy in a physiologic saline solution followed by balloon dilation of the hole. For the first series of tests, 6-mm-diameter noncompliant balloons were used and replaced for the second series by 6-mm-diameter cutting balloons. Each procedure was performed 5 times (5 fenestrations per balloon type). The fenestrations were examined visually and with light and scanning electron microscopy. Each fenestration demonstrated various degrees of fraying and/or tearing regardless of the device. The monofilament twill weave of the Talent endograft tore in the warp direction up to 7.09±0.46 mm at high energy compared with 2.41±0.26 mm for the Endurant multifilament device. The fenestrations of the 3 endografts with multifilament weave (Zenith, Anaconda, and Endurant) showed more fraying; fenestration areas in the multifilament Endurant were >10 mm 2 at low and high energy. The fenestrations were free of melted fibers, but minor blackening of the filaments was observed in all devices. Overall, the cutting balloons resulted in worse tearing and damage. Of note, the edges of the dilated laser-formed fenestrations of the Talent and the Endurant grafts demonstrated evidence of additional shredded yarns. In situ fenestration does not cause any melting of the polyester; however, the observed structural damage to the fabric construction must be carefully considered. Cutting balloons caused various levels of tearing compared to the noncompliant balloons and cannot be recommended for use in this application. Rather, noncompliant balloons should be employed, but only with endografts constructed from multifilament yarns

Latest development of laser cutting

OpenAIRE

Wetzig, Andreas; Herwig, Patrick; Hauptmann, Jan; Goppold, Cindy; Baumann, Robert; Fürst, Andreas; Rose, Michael; Pinder, Thomas; Mahrle, Achim; Beyer, Eckhard

2016-01-01

Laser cutting was one of the first applications of laser material processing. Today, laser cutting is the most widespread application among laser material processing besides laser marking. Meanwhile, nearly each material can be cut by means of a laser, in particular since ultra short pulse lasers are available in the power range of up to 100 W. The to be cut material can come with thicknesses from a few microns till tens of millimeters as flat stock or as free form shapes. The paper will conc...

Laser cutting: influence on morphological and physicochemical properties of polyhydroxybutyrate.

Science.gov (United States)

Lootz, D; Behrend, D; Kramer, S; Freier, T; Haubold, A; Benkiesser, G; Schmitz, K P; Becher, B

2001-09-01

Polyhydroxybutyrate (PHB) is a biocompatible and resorbable implant material. For these reasons, it has been used for the fabrication of temporary stents, bone plates, nails and screws (Peng et al. Biomaterials 1996;17:685). In some cases, the brittle mechanical properties of PHB homopolymer limit its application. A typical plasticizer, triethylcitrate (TEC), was used to overcome such limitations by making the material more pliable. In the past few years, CO2-laser cutting of PHB was used in the manufacturing of small medical devices such as stents. Embrittlement of plasticized PHB tubes has been observed, after laser machining. Consequently, the physicochemical and morphological properties of laser-processed surfaces and cut edges of plasticized polymer samples were examined to determine the extent of changes in polymer properties as a result of laser machining. These studies included determination of the depth of the laser-induced heat affected zone by polariscopy of thin polymer sections. Molecular weight changes and changes in the TEC content as a function of distance from the laser-cut edge were determined. In a preliminary test, the cellular response to the processed material was investigated by cell culture study of L929 mouse fibroblasts on laser-machined surfaces. The heat-affected zone was readily classified into four different regions with a total depth of about 60 to 100 microm (Klamp, Master Thesis, University of Rostock, 1998). These results correspond well with the chemical analysis and molecular weight measurements. Furthermore, it was found that cells grew preferentially on the laser-machined area. These findings have significant implications for the manufacture of medical implants from PHB by laser machining.

Fabrication of recyclable superhydrophobic cotton fabrics

Science.gov (United States)

Han, Sang Wook; Park, Eun Ji; Jeong, Myung-Geun; Kim, Il Hee; Seo, Hyun Ook; Kim, Ju Hwan; Kim, Kwang-Dae; Kim, Young Dok

2017-04-01

Commercial cotton fabric was coated with SiO2 nanoparticles wrapped with a polydimethylsiloxane (PDMS) layer, and the resulting material surface showed a water contact angle greater than 160°. The superhydrophobic fabric showed resistance to water-soluble contaminants and maintained its original superhydrophobic properties with almost no alteration even after many times of absorption-washing cycles of oil. Moreover, superhydrophobic fabric can be used as a filter to separate oil from water. We demonstrated a simple method of fabrication of superhydrophobic fabric with potential interest for use in a variety of applications.

Investigation on welding and cutting methods for blanket support legs of fusion experimental reactors

International Nuclear Information System (INIS)

Tokami, Ikuhide; Nakahira, Masataka; Kurasawa, Toshimasa; Sato, Satoshi; Furuya, Kazuyuki; Hatano, Toshihisa; Takatsu, Hideyuki; Kuroda, Toshimasa.

1996-07-01

A toroidally-and poloidally-divided modular blanket has been proposed for a fusion experimental reactor, such as ITER, to enhance its maintainability as well as improve its fabricability. The blanket module, typically the size of 1 m wide, 1-2 m high and 0.4 m deep and the weight of 4 ton, will be supported by support legs which are extruded from back of the module and connected to a 70-100 mm thick strong back plate. The support leg has to withstand large electromagnetic force during plasma disruption and provide the way for in-situ module replacement by remote handling. For the connection method of the support leg to the back plate, a welding approach has been investigated here in terms of its high reliability against the large electromagnetic loads. For the welding approach, the support leg needs to be 70 mm thick, and the working space for welding/cutting heads are limited to 100 mm x 150 mm adjacent to the support leg. Based on a comparison of several welding methods, e.g. NGTIG, NGMIG and laser, NGTIG has been selected as a reference due to its well-established technology and the least R and D required. As for the cutting method, a plasma cutting has been given the highest priority to be pursued because of its compactness and high speed. Through preliminary design studies, the possibility of small welding/cutting heads that will work in the limited space has been shown, and maintenance route for in-situ module replacement with pre-and postfixture of the module has been investigated. Also preliminary R and Ds have resulted in; 1)the welding distortion is predictable according to the shape of weld groove and adjustable to meet the placement requirement of the module first wall, 2)the plasma cut surface can be rewelded without machining, 3)the welding/cutting time will meet the requirement of maintenance time. (author)

A microband lactate biosensor fabricated using a water-based screen-printed carbon ink.

Science.gov (United States)

Rawson, F J; Purcell, W M; Xu, J; Pemberton, R M; Fielden, P R; Biddle, N; Hart, J P

2009-01-15

The present study demonstrated for the first time that screen-printed carbon microband electrodes fabricated from water-based ink can readily detect H(2)O(2) and that the same ink, with the addition of lactate oxidase, can be used to construct microband biosensors to measure lactate. These microband devices were fabricated by a simple cutting procedure using conventional sized screen-printed carbon electrodes (SPCEs) containing the electrocatalyst cobalt phthalocyanine (CoPC). These devices were characterised with H(2)O(2) using several electrochemical techniques. Cyclic voltammograms were found to be sigmoidal; a current density value of 4.2 mA cm(-2) was obtained. A scan rate study revealed that the mass transport mechanism was a mixture of radial and planar diffusion. However, a further amperometric study under quiescent and hydrodynamic conditions indicated that radial diffusion predominated. A chronoamperometric study indicated that steady-state currents were obtained with these devices for a variety of H(2)O(2) concentrations and that the currents were proportional to the analyte concentration. Lactate microband biosensors were then fabricated by incorporating lactate oxidase into the water-based formulation prior to printing and then cutting as described. Voltammograms demonstrated that lactate oxidase did not compromise the integrity of the electrode for H(2)O(2) detection. A potential of +400 mV was selected for a calibration study, which showed that lactate could be measured over a dynamic range of 1-10mM which was linear up to 6mM; a calculated lower limit of detection of 289 microM was ascertained. This study provides a platform for monitoring cell metabolism in-vitro by measuring lactate electrochemically via a microband biosensor.

CALCULATION OF LASER CUTTING COSTS

Directory of Open Access Journals (Sweden)

Bogdan Nedic

2016-09-01

Full Text Available The paper presents description methods of metal cutting and calculation of treatment costs based on model that is developed on Faculty of mechanical engineering in Kragujevac. Based on systematization and analysis of large number of calculation models of cutting with unconventional methods, mathematical model is derived, which is used for creating a software for calculation costs of metal cutting. Software solution enables resolving the problem of calculating the cost of laser cutting, comparison' of costs made by other unconventional methods and provides documentation that consists of reports on estimated costs.

Tubing and cable cutting tool

Science.gov (United States)

Mcsmith, D. D.; Richardson, J. I. (Inventor)

1984-01-01

A hand held hydraulic cutting tool was developed which is particularly useful in deactivating ejection seats in military aircraft rescue operations. The tool consists primarily of a hydraulic system composed of a fluid reservoir, a pumping piston, and an actuator piston. Mechanical cutting jaws are attached to the actuator piston rod. The hydraulic system is controlled by a pump handle. As the pump handle is operated the actuator piston rod is forced outward and thus the cutting jaws are forced together. The frame of the device is a flexible metal tubing which permits easy positioning of the tool cutting jaws in remote and normally inaccessible locations. Bifurcated cutting edges ensure removal of a section of the tubing or cable to thereby reduce the possibility of accidental reactivation of the tubing or cable being severed.

Cutting concrete with abrasion jet

International Nuclear Information System (INIS)

Yie, G.G.

1982-01-01

Fluidyne Corporation has developed a unique process and apparatus that allow selected abrasives to be introduced into high-speed waterjet to produce abrasive-entrained waterjet that has high material-cutting capabilities, which is termed by Fluidyne as the Abrasion Jet. Such Abrasion Jet has demonstrated capability in cutting hard rock and concrete at a modest pressure of less than 1360 bars (20,000 psi) and a power input of less than 45 kW (60 horsepower). Abrasion Jet cutting of concrete is characterized by its high rate of cutting, flexible operation, good cut quality, and relatively low costs. This paper presents a general description of this technology together with discussions of recent test results and how it could be applied to nuclear decontamination and decommissioning work. 8 references

Influence of cutting parameters on the depth of subsurface deformed layer in nano-cutting process of single crystal copper.

Science.gov (United States)

Wang, Quanlong; Bai, Qingshun; Chen, Jiaxuan; Su, Hao; Wang, Zhiguo; Xie, Wenkun

2015-12-01

Large-scale molecular dynamics simulation is performed to study the nano-cutting process of single crystal copper realized by single-point diamond cutting tool in this paper. The centro-symmetry parameter is adopted to characterize the subsurface deformed layers and the distribution and evolution of the subsurface defect structures. Three-dimensional visualization and measurement technology are used to measure the depth of the subsurface deformed layers. The influence of cutting speed, cutting depth, cutting direction, and crystallographic orientation on the depth of subsurface deformed layers is systematically investigated. The results show that a lot of defect structures are formed in the subsurface of workpiece during nano-cutting process, for instance, stair-rod dislocations, stacking fault tetrahedron, atomic clusters, vacancy defects, point defects. In the process of nano-cutting, the depth of subsurface deformed layers increases with the cutting distance at the beginning, then decreases at stable cutting process, and basically remains unchanged when the cutting distance reaches up to 24 nm. The depth of subsurface deformed layers decreases with the increase in cutting speed between 50 and 300 m/s. The depth of subsurface deformed layer increases with cutting depth, proportionally, and basically remains unchanged when the cutting depth reaches over 6 nm.

Woven electrochemical fabric-based test sensors (WEFTS): a new class of multiplexed electrochemical sensors.

Science.gov (United States)

Choudhary, Tripurari; Rajamanickam, G P; Dendukuri, Dhananjaya

2015-05-07

We present textile weaving as a new technique for the manufacture of miniature electrochemical sensors with significant advantages over current fabrication techniques. Biocompatible silk yarn is used as the material for fabrication instead of plastics and ceramics used in commercial sensors. Silk yarns are coated with conducting inks and reagents before being handloom-woven as electrodes into patches of fabric to create arrays of sensors, which are then laminated, cut and packaged into individual sensors. Unlike the conventionally used screen-printing, which results in wastage of reagents, yarn coating uses only as much reagent and ink as required. Hydrophilic and hydrophobic yarns are used for patterning so that sample flow is restricted to a small area of the sensor. This simple fluidic control is achieved with readily available materials. We have fabricated and validated individual sensors for glucose and hemoglobin and a multiplexed sensor, which can detect both analytes. Chronoamperometry and differential pulse voltammetry (DPV) were used to detect glucose and hemoglobin, respectively. Industrial quantities of these sensors can be fabricated at distributed locations in the developing world using existing skills and manufacturing facilities. We believe such sensors could find applications in the emerging area of wearable sensors for chemical testing.

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Mengjiao Yu; Ramadan Ahmed; Mark Pickell; Len Volk; Lei Zhou; Zhu Chen; Aimee Washington; Crystal Redden

2003-09-30

The Quarter began with installing the new drill pipe, hooking up the new hydraulic power unit, completing the pipe rotation system (Task 4 has been completed), and making the SWACO choke operational. Detailed design and procurement work is proceeding on a system to elevate the drill-string section. The prototype Foam Generator Cell has been completed by Temco and delivered. Work is currently underway to calibrate the system. Literature review and preliminary model development for cuttings transportation with polymer foam under EPET conditions are in progress. Preparations for preliminary cuttings transport experiments with polymer foam have been completed. Two nuclear densitometers were re-calibrated. Drill pipe rotation system was tested up to 250 RPM. Water flow tests were conducted while rotating the drill pipe up to 100 RPM. The accuracy of weight measurements for cuttings in the annulus was evaluated. Additional modifications of the cuttings collection system are being considered in order to obtain the desired accurate measurement of cuttings weight in the annular test section. Cutting transport experiments with aerated fluids are being conducted at EPET, and analyses of the collected data are in progress. The printed circuit board is functioning with acceptable noise level to measure cuttings concentration at static condition using ultrasonic method. We were able to conduct several tests using a standard low pass filter to eliminate high frequency noise. We tested to verify that we can distinguish between different depths of sand in a static bed of sand. We tested with water, air and a mix of the two mediums. Major modifications to the DTF have almost been completed. A stop-flow cell is being designed for the DTF, the ACTF and Foam Generator/Viscometer which will allow us to capture bubble images without the need for ultra fast shutter speeds or microsecond flash system.

Using internally cooled cutting tools in the machining of difficult-to-cut materials based on Waspaloy

Directory of Open Access Journals (Sweden)

Yahya Isik

2016-05-01

Full Text Available Nickel-based superalloys such as Waspaloy are used for engine components and in the nuclear industry, where considerable strength and corrosion resistance at high operating temperatures are called for. These characteristics of such alloys cause increases in cutting temperature and resultant tool damage, even at low cutting speeds and low feed rates. Thus, they are classified as difficult-to-cut materials. This article presents a cooling method to be used in metal cutting based on a tool holder with a closed internal cooling system with cooling fluid circulating inside. Hence, a green cooling method that does not harm the environment and is efficient in removing heat from the cutting zone was developed. A series of cutting experiments were conducted to investigate the practicality and effectiveness of the internally cooled tool model. The developed system achieved up to 13% better surface quality than with dry machining, and tool life was extended by 12%. The results clearly showed that with the reduced cutting temperature of the internal cooling, it was possible to control the temperature and thus prevent reaching the critical cutting temperature during the turning process, which is vitally important in extending tool life during the processing of Waspaloy.

Laser Cutting, Development Trends

DEFF Research Database (Denmark)

Olsen, Flemming Ove

1999-01-01

In this paper a short review of the development trends in laser cutting will be given.The technology, which is the fastest expanding industrial production technology will develop in both its core market segment: Flat bed cutting of sheet metal, as it will expand in heavy industry and in cutting...... of 3-dimensional shapes.The CO2-laser will also in the near future be the dominating laser source in the market, although the new developments in ND-YAG-lasers opens for new possibilities for this laser type....

Water-Cut Sensor System

KAUST Repository

Karimi, Muhammad Akram; Shamim, Atif; Arsalan, Muhammad

2018-01-01

Provided in some embodiments is a method of manufacturing a pipe conformable water-cut sensors system. Provided in some embodiments is method for manufacturing a water-cut sensor system that includes providing a helical T-resonator, a helical ground

Effects of cutting and maturity on antioxidant activity of fresh-cut tomatoes

NARCIS (Netherlands)

Moreira Lana, M.; Tijskens, L.M.M.; Kooten, van O.

2005-01-01

To investigate the changes in total antioxidant activity of fresh-cut tomato during storage, tomato fruits harvested at three different stages of maturity were cut into 7-mm thick slices and stored at 5°C. Intact (control) fruits were stored in the same conditions. The antioxidant activity was

米国サブプライム住宅ローン危機と国際金融不安

OpenAIRE

毛利, 良一; Ryoichi, Mohri

2008-01-01

A lot of literature has analyzed the subprime mortgage crisis, an ongoing economic problem manifesting itself through liquidity issues in the global banking system owing to foreclosures which accelerated in the United States in late 2006 and triggered a global financial crisis during 2007 and 2008.This paper firstly focuses on the causes, background and characteristics of the subprime mortgage crisis. This crisis has varied and complex components such as teaser interest rates for the subprime...

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2013-02-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

Quality Analysis of Cutting Steel Using Laser

Directory of Open Access Journals (Sweden)

Vladislav Markovič

2012-12-01

Full Text Available The article explores the quality dependence of the edge surface of steel C45 LST EN 10083-1 obtained cutting the material using laser on different cutting regimes and variations in the thickness of trial steel. The paper presents the influence of the main modes of laser cutting equipment Trulaser 3030, including cutting speed, pressure, angle and the thickness of the surface on the quality characteristics of the sample. The quality of the edge after laser cutting is the most important indicator influencing such technological spread in industry worldwide. Laser cutting is the most popular method of material cutting. Therefore, the article focuses on cutting equipment, cutting defects and methods of analysis. Research on microstructure, roughness and micro-toughness has been performed with reference to edge samples. At the end of the publication, conclusions are drawn.Article in Lithuanian

Effect of cutting medium temperatures on rooting process and root primordium differentiation of hardwood cuttings of tetraploid robinia pseudoacacia cutting medium temperatures of tetraploid robinia pseudoacacia

International Nuclear Information System (INIS)

Ling, W.X.; Jine, Q.; Zhong, Z.

2014-01-01

In this study, to examine the effect of heat treatment on the rooting and root development of hardwood cuttings of the tetraploid Robinia pseudoacacia, cuttings of 1-year-old stems were taken from 3-year-old mother trees and treated with IBA solution (1000 mg/L) for 6 h, with water was as a control. Treated cuttings were rooted in heated or unheated nursery beds. Samples were collected on day ten after planting, and then for every five days. The bases of the cuttings were embedded in paraffin and sectioned before being examined under a microscope to determine whether there had been any morphological changes. We found no root primordia in the tissues of the hardwood cuttings of the tetraploid Robinia pseudoacacia before cutting. In the heated bed, adventitious roots originated from callus tissue and the junction between the pith rays and cortical parenchyma cells, and in the unheated bed, adventitious roots originated only from callus tissue. The rooting process involved callus formation, adventitious root formation and elongation; rooting occurred 5-7 days earlier in the heated cuttings than in the unheated ones, and rooting rates were significantly higher in the former 30 days and 50 days after cutting; the minimum effective accumulated temperatures for these three stages were 109.25 degree C, 211.68 degree C and 301.38 degree C, respectively. Our results revealed that heating the soil can promote adventitious root formation, speed up the rooting rate, and cut the propagation period of the tetraploid Robinia pseudoacacia. (author)

New Modelling Strategies For Metal Cutting

International Nuclear Information System (INIS)

Rosa, Pedro A. R.; Martins, Paulo A. F.; Atkins, Anthony G.

2007-01-01

This paper draws from the 'plasticity and friction only' view of metal cutting to the presentation of new modelling strategies based on the interaction between finite elements and modern ductile fracture mechanics. The overall presentation is supported by specially designed orthogonal metal cutting experiments that were performed on Lead test specimens under laboratory-controlled conditions. Comparisons between theoretical predictions and experimental results comprise a wide range of topics such as material flow, cutting forces and specific cutting pressure. The paper demonstrates that while material flow and chip formation can be successfully modelled by traditional 'plasticity and friction only' analyses, the contribution of the fracture work involved in the formation of new surfaces is essential for obtaining good estimates of cutting forces and of the specific cutting pressure

Cutting method and device underwater

International Nuclear Information System (INIS)

Takano, Genta; Kamei, Hiromasa; Beppu, Seiji

1998-01-01

A place of material to be cut is surrounded by an openable/closable box. The material to be cut is cut underwater, and materials generated in this case are removed from the cut portion by a pressurized water jet. The removed materials are sucked and recovered together with water in the box. Among the materials caused by the cutting underwater, solid materials not floating on water are caused to stay in the midway of a sucking and recovering channel. A large sucking force might be required for the entire region of the sucking and recovering channel when sucking and recovering large sized solid materials not floating on water, but even large sized materials can be recovered easily according to the present invention since they are recovered after being sucked and stayed in the midway of the sucking and recovering channel. (N.H.)

Cutting zone area and chip morphology in high-speed cutting of titanium alloy Ti-6Al-4V

International Nuclear Information System (INIS)

Ke, Qing Chan; Xu, Daochun; Xiong, Dan Ping

2017-01-01

The titanium alloy Ti-6Al-4V has superior properties but poor machinability, yet is widely used in aerospace and biomedical industries. Chip formation and cutting zone area are important factors that have received limited attention. Thus, we propose a high-speed orthogonal cutting model for serrated chip formation. The high speed orthogonal cutting of Ti-6Al-4V was studied with a cutting speed of 10-160 m/min and a feed of 0.07-0.11 mm/r. Using theoretical models and experimental results, parameters such as chip shape, serration level, slip angle, and shear slip distance were investigated. Cutting zone boundaries (tool-chip contact length, length of shear plane, and critical slip plane) and cutting zone area were obtained. The results showed that discontinuous, long-curling, and continuous chips were formed at low, medium, and high speeds, respectively. Serration level, shear slip distance, and slip angle rose with increasing cutting speed. The length of shear plane, tool-chip contact, and critical slip plane varied subtly with increased cutting speed, and rose noticeably with increased feed. Cutting zone area grew weakly with increased cutting speed, levelling off at high cutting speed; however, it rose noticeably with increased feed. This study furthers our understanding of the shear slip phenomenon and the mechanism of serrated chip formation

Cutting zone area and chip morphology in high-speed cutting of titanium alloy Ti-6Al-4V

Energy Technology Data Exchange (ETDEWEB)

Ke, Qing Chan; Xu, Daochun; Xiong, Dan Ping [School of Technology, Beijing Forestry University, Beijing (China)

2017-01-15

The titanium alloy Ti-6Al-4V has superior properties but poor machinability, yet is widely used in aerospace and biomedical industries. Chip formation and cutting zone area are important factors that have received limited attention. Thus, we propose a high-speed orthogonal cutting model for serrated chip formation. The high speed orthogonal cutting of Ti-6Al-4V was studied with a cutting speed of 10-160 m/min and a feed of 0.07-0.11 mm/r. Using theoretical models and experimental results, parameters such as chip shape, serration level, slip angle, and shear slip distance were investigated. Cutting zone boundaries (tool-chip contact length, length of shear plane, and critical slip plane) and cutting zone area were obtained. The results showed that discontinuous, long-curling, and continuous chips were formed at low, medium, and high speeds, respectively. Serration level, shear slip distance, and slip angle rose with increasing cutting speed. The length of shear plane, tool-chip contact, and critical slip plane varied subtly with increased cutting speed, and rose noticeably with increased feed. Cutting zone area grew weakly with increased cutting speed, levelling off at high cutting speed; however, it rose noticeably with increased feed. This study furthers our understanding of the shear slip phenomenon and the mechanism of serrated chip formation.

Effects of cutting and maturity on antioxidant activity of fresh-cut tomatoes

NARCIS (Netherlands)

Moreira Lana, M.; Tijskens, L.M.M.

2006-01-01

To investigate the changes in total antioxidant activity of fresh-cut tomato during storage, tomato fruits harvested at three different stages of maturity were cut into 7-mm thick slices and stored at 5 °C. Intact fruits were stored in the same conditions as a control. The antioxidant activity was

Respiration rate and ethylene production of fresh cut lettuce as affected by cutting grade

Directory of Open Access Journals (Sweden)

J. MARTÍNEZ

2008-12-01

Full Text Available For designing optimal polymeric films for modified atmosphere packaging of whole heads as well as for minimally fresh processed (fresh-cut Iceberg lettuce ‘Coolguard’, the effect of several cutting grades on respiration rate (RR and ethylene production at 5ºC was studied. According to common industrial practices cutting grades less than 0.5 cm, between 0.5 and 1 cm, and 2 cm length were selected. Results from four experiments were compared to those obtained for whole heads in which a homogenous range of 6 to 8 ml CO2 kg-1 h-1 in RR was found. Compared to whole heads, in fresh-cut lettuce the RR was 2-fold higher. The lowest cutting grade showed the highest respiration rate, and no significant differences in RR among lettuce pieces of intermediate and the highest grades were found. No ethylene production was detected in whole heads, while in minimally processed lettuce pieces only traces were found. For avoiding risks of anaerobic respiration and excessive CO2 levels within packages containing fresh-cut lettuce pieces lower than 0.5 cm length, films with relatively high O2 permeability like standard polypropylene or low-density polyethylene must be selected.;

Test tube systems with cutting/recombination operations

Energy Technology Data Exchange (ETDEWEB)

Freund, R. [Technische Universitaet Wien (Austria); Csuhaj-Varju, E. [Computer and Automation Institute, Budapest (Hungary); Wachtler, F. [Universitaet Wien (Austria)

1996-12-31

We introduce test tube systems based on operations that are closely related to the splicing operations, i.e. we consider the operations of cutting a string at a specific site into two pieces with marking them at the cut ends and of recombining two strings with specifically marked endings. Whereas in the splicing of two strings these strings are cut at specific sites and the cut pieces are recombined immediately in a crosswise way, in CR(cutting/recombination)-schemes cutting can happen independently from recombining the cut pieces. Test tube systems based on these operations of cutting and recombination turn out to have maximal generative power even if only very restricted types of input filters for the test tubes are used for the redistribution of the contents of the test tubes after a period of cuttings and recombinations in the test tubes. 10 refs.

Fabrication of U-Pu-Zr metallic fuel containing minor actinides

International Nuclear Information System (INIS)

Kurata, Masaki; Sasahara, Akihiro; Inoue, Tadashi; Betti, M.; Babelot, J.F.; Spirlet, J.C.; Koch, L.

1997-01-01

Rods of UPuZr alloy containing 5% minor actinides, 2% minor actinides and 2% rare-earth elements, and 5% minor actinides and 5% rare-earth elements have been fabricated by casting in yttria molds. Parts of the ingots were cut off for quantitative analysis and the rods characterized to the required extent, which included measurement of length, weight, diameter, and bending. For selected samples, metallographic study was carried out to examine the dispersion of the various phases contained in the alloy. Finally, the rods were encapsulated in stainless steel pin with the UPuZr reference after sodium bonding for the irradiation study. (author)

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Stefan Miska; Nicholas Takach; Kaveh Ashenayi

2004-01-31

Final design of the mast was completed (Task 5). The mast is consisting of two welded plate girders, set next to each other, and spaced 14-inches apart. Fabrication of the boom will be completed in two parts solely for ease of transportation. The end pivot connection will be made through a single 2-inch diameter x 4 feet-8 inch long 316 SS bar. During installation, hard piping make-ups using Chiksan joints will connect the annular section and 4-inch return line to allow full movement of the mast from horizontal to vertical. Additionally, flexible hoses and piping will be installed to isolate both towers from piping loads and allow recycling operations respectively. Calibration of the prototype Foam Generator Cell has been completed and experiments are now being conducted. We were able to generate up to 95% quality foam. Work is currently underway to attach the Thermo-Haake RS300 viscometer and install a view port with a microscope to measure foam bubble size and bubble size distribution. Foam rheology tests (Task 13) were carried out to evaluate the rheological properties of the proposed foam formulation. After successful completion of the first foam test, two sets of rheological tests were conducted at different foam flow rates while keeping other parameters constant (100 psig, 70F, 80% quality). The results from these tests are generally in agreement with the previous foam tests done previously during Task 9. However, an unanticipated observation during these tests was that in both cases, the frictional pressure drop in 2 inch pipe was lower than that in the 3 inch and 4 inch pipes. We also conducted the first foam cuttings transport test during this quarter. Experiments on aerated fluids without cuttings have been completed in ACTF (Task 10). Gas and liquid were injected at different flow rates. Two different sets of experiments were carried out, where the only difference was the temperature. Another set of tests was performed, which covered a wide range of

Laser cutting system

Science.gov (United States)

Dougherty, Thomas J

2015-03-03

A workpiece cutting apparatus includes a laser source, a first suction system, and a first finger configured to guide a workpiece as it moves past the laser source. The first finger includes a first end provided adjacent a point where a laser from the laser source cuts the workpiece, and the first end of the first finger includes an aperture in fluid communication with the first suction system.

Trim cut machining and surface integrity analysis of Nimonic 80A alloy using wire cut EDM

Directory of Open Access Journals (Sweden)

Amitesh Goswami

2017-02-01

Full Text Available This present work deals with the features of trim cut wire EDM machining of Nimonic 80A in terms of machining parameters, to predict material removal rate (MRR, surface roughness (Ra, wire wear ratio (WWR and microstructure analysis. Trim cut is performed after rough cut to remove the rough layer deposited after machining due to melting and re-solidification of the eroded metal from workpiece as well as from wire electrode. Taguchi’s design of experiments methodology has been used for planning and designing the experiments. The relative significance of various factors has also been evaluated and analyzed using ANOVA. The results clearly indicate trim cut potential for high surface finish compared to rough cut machining.

Identification and characterization of a novel Cut family cDNA that encodes human copper transporter protein CutC

International Nuclear Information System (INIS)

Li Jixi; Ji Chaoneng; Chen Jinzhong; Yang Zhenxing; Wang Yijing; Fei, Xiangwei; Zheng Mei; Gu Xing; Wen Ge; Xie Yi; Mao Yumin

2005-01-01

Copper is an essential heavy metal trace element that plays important roles in cell physiology. The Cut family was associated with the copper homeostasis and involved in several important metabolisms, such as uptake, storage, delivery, and efflux of copper. In this study, a novel Cut family cDNA was isolated from the human fetal brain library, which encodes a 273 amino acid protein with a molecular mass of about 29.3 kDa and a calculated pI of 8.17. It was named hCutC (human copper transporter protein CutC). The ORF of hCutC gene was cloned into pQE30 vector and expressed in Escherichia coli M15. The secreted hCutC protein was purified to a homogenicity of 95% by using the Ni-NTA affinity chromatography. RT-PCR analysis showed that the hCutC gene expressed extensively in human tissues. Subcellular location analysis of hCutC-EGFP fusion protein revealed that hCutC was distributed to cytoplasm of COS-7 cells, and both cytoplasm and nucleus of AD293 cells. The results suggest that hCutC may be one shuttle protein and play important roles in intracellular copper trafficking

Laser Cutting of Different Materials

Directory of Open Access Journals (Sweden)

Kadir ÇAVDAR

2013-08-01

Full Text Available In this paper; in general potential developments and trends of a particular machining field by extensively evaluating present studies of laser beam machining have been discussed. As it is indicated below, technical literatures have been subsumed under five major headlines: Experimental studies, reviews, optimization researches of the cutting parameters, theoretical modelling studies of laser beam cutting and academic studies relating to laser cutting

Comparative study of 0° X-cut and Y + 36°-cut lithium niobate high-voltage sensing

Science.gov (United States)

Patel, N.; Branch, D. W.; Schamiloglu, E.; Cular, S.

2015-08-01

A comparison study between Y + 36° and 0° X-cut lithium niobate (LiNbO3) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y + 36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5 μs voltage pulses to both crystals, the voltage-induced shift scaled linearly with voltage. For the Y + 36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz-100 kHz. Using the same conditions as the Y + 36° cut, the 0° X-cut crystal sensed a shift of 10-273 ps for DC voltages and 189-813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250-2 ns and the Y + 36°-cut crystal sensed a time shift of 0.115-1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. When the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment.

NCSX Vacuum Vessel Fabrication

International Nuclear Information System (INIS)

Viola ME; Brown T; Heitzenroeder P; Malinowski F; Reiersen W; Sutton L; Goranson P; Nelson B; Cole M; Manuel M; McCorkle D.

2005-01-01

The National Compact Stellarator Experiment (NCSX) is being constructed at the Princeton Plasma Physics Laboratory (PPPL) in conjunction with the Oak Ridge National Laboratory (ORNL). The goal of this experiment is to develop a device which has the steady state properties of a traditional stellarator along with the high performance characteristics of a tokamak. A key element of this device is its highly shaped Inconel 625 vacuum vessel. This paper describes the manufacturing of the vessel. The vessel is being fabricated by Major Tool and Machine, Inc. (MTM) in three identical 120 o vessel segments, corresponding to the three NCSX field periods, in order to accommodate assembly of the device. The port extensions are welded on, leak checked, cut off within 1-inch of the vessel surface at MTM and then reattached at PPPL, to accommodate assembly of the close-fitting modular coils that surround the vessel. The 120 o vessel segments are formed by welding two 60 o segments together. Each 60 o segment is fabricated by welding ten press-formed panels together over a collapsible welding fixture which is needed to precisely position the panels. The vessel is joined at assembly by welding via custom machined 8-inch (20.3 cm) wide spacer ''spool pieces''. The vessel must have a total leak rate less than 5 X 10 -6 t-l/s, magnetic permeability less than 1.02(micro), and its contours must be within 0.188-inch (4.76 mm). It is scheduled for completion in January 2006

Optical Cutting Interruption Sensor for Fiber Lasers

Directory of Open Access Journals (Sweden)

Benedikt Adelmann

2015-09-01

Full Text Available We report on an optical sensor system attached to a 4 kW fiber laser cutting machine to detect cutting interruptions. The sensor records the thermal radiation from the process zone with a modified ring mirror and optical filter arrangement, which is placed between the cutting head and the collimator. The process radiation is sensed by a Si and InGaAs diode combination with the detected signals being digitalized with 20 kHz. To demonstrate the function of the sensor, signals arising during fusion cutting of 1 mm stainless steel and mild steel with and without cutting interruptions are evaluated and typical signatures derived. In the recorded signals the piercing process, the laser switch on and switch off point and waiting period are clearly resolved. To identify the cutting interruption, the signals of both Si and InGaAs diodes are high pass filtered and the signal fluctuation ranges being subsequently calculated. Introducing a correction factor, we identify that only in case of a cutting interruption the fluctuation range of the Si diode exceeds the InGaAs diode. This characteristic signature was successfully used to detect 80 cutting interruptions of 83 incomplete cuts (alpha error 3.6% and system recorded no cutting interruption from 110 faultless cuts (beta error of 0. This particularly high detection rate in combination with the easy integration of the sensor, highlight its potential for cutting interruption detection in industrial applications.

Radioactive wear measurements of cutting tools made of metal in cutting aluminium alloys

International Nuclear Information System (INIS)

Frevert, E.

1977-01-01

The possibility of making quick checkings of the inhomogeneities of turning materials with radioactive wear measurements has been tested. After activation analysis of the long-lived radioisotopes of cutting tools made of hard metal a method for loss-free collection of the turnings has been developed. The detection limit of the abrasion is about 10 -8 g, the measuring times are 5-10 minutes. Special radiation protection measures are not necessary. An analysis of the abrasion showed that at the beginning of cutting the amount of cobalt is 6 times higher than in the normal composition of the used cutting tools. (author)

Economic technology of laser cutting

Science.gov (United States)

Fedin, Alexander V.; Shilov, Igor V.; Vassiliev, Vladimir V.; Malov, Dmitri V.; Peskov, Vladimir N.

2000-02-01

The laser cutting of color metals and alloys by a thickness more than 2 mm has significant difficulties due to high reflective ability and large thermal conduction. We made it possible to raise energy efficiency and quality of laser cutting by using a laser processing system (LPS) consisting both of the YAG:Nd laser with passive Q-switching on base of LiF:F2- crystals and the CO2 laser. A distinctive feature of the LPS is that the radiation of different lasers incorporated in a coaxial beam has simultaneously high level of peak power (more than 400 kW in a TEM00 mode) and significant level of average power (up to 800 W in a TEM01 mode of the CO2 laser). The application of combined radiation for cutting of an aluminum alloy of D16 type made it possible to decrease the cutting energy threshold in 1.7 times, to increase depth of treatment from 2 up to 4 mm, and velocity from 0.015 up to 0.7 m/min, and also to eliminate application of absorptive coatings. At cutting of steels the velocity of treatment was doubled, and also an oxygen flow was eliminated from the technological process and replaced by the air. The obtained raise of energy efficiency and quality of cutting is explained by an essential size reducing of a formed penetration channel and by the shifting of a thermal cutting mode from melting to evaporation. The evaluation of interaction efficiency of a combined radiation was produced on the basis of non-stationary thermal-hydrodynamic model of a heating source moving as in the cutting direction, and also into the depth of material.

Development of cutting device for irradiated fuel rod

International Nuclear Information System (INIS)

Lee, E. P.; Jun, Y. B.; Hong, K. P.; Min, D. K.; Lee, H. K.; Su, H. S.; Kim, K. S.; Kwon, H. M.; Joo, Y. S.; Yoo, K. S.; Joo, J. S.; Kim, E. K.

2004-01-01

Post Irradiation Examination(PIE) on irradiated fuel rods is essential for the evaluation of integrity and irradiation performance of fuel rods of commercial reactor fuel. For PIE, fuel rods should be cut very precisely. The cutting positions selected from NDT data are very important for further destructive examination and analysis. A fuel rod cutting device was developed witch can cut fuel rods longitudinal very precisely and can also cut the fuels into the same length rod cuts repeatedly. It is also easy to remove the fuel cutting powder after cutting works and it can extend the life time of cutting device and lower the contamination level of hot cell

ADVANCED CUTTINGS TRANSPORT STUDY

Energy Technology Data Exchange (ETDEWEB)

Troy Reed; Stefan Miska; Nicholas Takach; Kaveh Ashenayi; Gerald Kane; Mark Pickell; Len Volk; Mike Volk; Barkim Demirdal; Affonso Lourenco; Evren Ozbayoglu; Paco Vieira; Lei Zhou

2000-01-30

This is the second quarterly progress report for Year 2 of the ACTS project. It includes a review of progress made in Flow Loop development and research during the period of time between Oct 1, 2000 and December 31, 2000. This report presents a review of progress on the following specific tasks: (a) Design and development of an Advanced Cuttings Transport Facility (Task 2: Addition of a foam generation and breaker system), (b) Research project (Task 6): ''Study of Cuttings Transport with Foam Under LPAT Conditions (Joint Project with TUDRP)'', (c) Research project (Task 7): ''Study of Cuttings Transport with Aerated Muds Under LPAT Conditions (Joint Project with TUDRP)'', (d) Research project (Task 8): ''Study of Flow of Synthetic Drilling Fluids Under Elevated Pressure and Temperature Conditions'', (e) Research project (Task 9): ''Study of Foam Flow Behavior Under EPET Conditions'', (f) Research project (Task 10): ''Study of Cuttings Transport with Aerated Mud Under Elevated Pressure and Temperature Conditions'', (g) Research on instrumentation tasks to measure: Cuttings concentration and distribution in a flowing slurry (Task 11), and Foam properties while transporting cuttings. (Task 12), (h) Development of a Safety program for the ACTS Flow Loop. Progress on a comprehensive safety review of all flow-loop components and operational procedures. (Task 1S). (i) Activities towards technology transfer and developing contacts with Petroleum and service company members, and increasing the number of JIP members. The tasks Completed During This Quarter are Task 7 and Task 8.

Submerged cutting characteristics of abrasive suspension jet

International Nuclear Information System (INIS)

Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroyuki

2015-01-01

An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth under submerged condition divided by the cutting depth in air at the same standoff distance. The relative cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

Effects of Cutting Edge Microgeometry on Residual Stress in Orthogonal Cutting of Inconel 718 by FEM.

Science.gov (United States)

Shen, Qi; Liu, Zhanqiang; Hua, Yang; Zhao, Jinfu; Lv, Woyun; Mohsan, Aziz Ul Hassan

2018-06-14

Service performance of components such as fatigue life are dramatically influenced by the machined surface and subsurface residual stresses. This paper aims at achieving a better understanding of the influence of cutting edge microgeometry on machined surface residual stresses during orthogonal dry cutting of Inconel 718. Numerical and experimental investigations have been conducted in this research. The cutting edge microgeometry factors of average cutting edge radius S¯, form-factor K , and chamfer were investigated. An increasing trend for the magnitudes of both tensile and compressive residual stresses was observed by using larger S¯ or introducing a chamfer on the cutting edges. The ploughing depth has been predicted based on the stagnation zone. The increase of ploughing depth means that more material was ironed on the workpiece subsurface, which resulted in an increase in the compressive residual stress. The thermal loads were leading factors that affected the surface tensile residual stress. For the unsymmetrical honed cutting edge with K = 2, the friction between tool and workpiece and tensile residual stress tended to be high, while for the unsymmetrical honed cutting edge with K = 0.5, the high ploughing depth led to a higher compressive residual stress. This paper provides guidance for regulating machine-induced residual stress by edge preparation.

Quantum Max-flow/Min-cut

Science.gov (United States)

Cui, Shawn X.; Freedman, Michael H.; Sattath, Or; Stong, Richard; Minton, Greg

2016-06-01

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

Quantum Max-flow/Min-cut

Energy Technology Data Exchange (ETDEWEB)

Cui, Shawn X., E-mail: xingshan@math.ucsb.edu [Department of Mathematics, University of California, Santa Barbara, California 93106 (United States); Quantum Architectures and Computation Group, Microsoft Research, Redmond, Washington 98052 (United States); Freedman, Michael H., E-mail: michaelf@microsoft.com [Department of Mathematics, University of California, Santa Barbara, California 93106 (United States); Microsoft Research, Station Q, University of California, Santa Barbara, California 93106 (United States); Sattath, Or, E-mail: sattath@gmail.com [Computer Science Division, University of California, Berkeley, California 94720 (United States); Stong, Richard, E-mail: stong@ccrwest.org; Minton, Greg, E-mail: gtminto@ccrwest.org [Center for Communications Research, La Jolla, California 92121 (United States)

2016-06-15

The classical max-flow min-cut theorem describes transport through certain idealized classical networks. We consider the quantum analog for tensor networks. By associating an integral capacity to each edge and a tensor to each vertex in a flow network, we can also interpret it as a tensor network and, more specifically, as a linear map from the input space to the output space. The quantum max-flow is defined to be the maximal rank of this linear map over all choices of tensors. The quantum min-cut is defined to be the minimum product of the capacities of edges over all cuts of the tensor network. We show that unlike the classical case, the quantum max-flow=min-cut conjecture is not true in general. Under certain conditions, e.g., when the capacity on each edge is some power of a fixed integer, the quantum max-flow is proved to equal the quantum min-cut. However, concrete examples are also provided where the equality does not hold. We also found connections of quantum max-flow/min-cut with entropy of entanglement and the quantum satisfiability problem. We speculate that the phenomena revealed may be of interest both in spin systems in condensed matter and in quantum gravity.

Cutting Class Harms Grades

Science.gov (United States)

Taylor, Lewis A., III

2012-01-01

An accessible business school population of undergraduate students was investigated in three independent, but related studies to determine effects on grades due to cutting class and failing to take advantage of optional reviews and study quizzes. It was hypothesized that cutting classes harms exam scores, attending preexam reviews helps exam…

Sodium-cutting: a new top-down approach to cut open nanostructures on nonplanar surfaces on a large scale.

Science.gov (United States)

Chen, Wei; Deng, Da

2014-11-11

We report a new, low-cost and simple top-down approach, "sodium-cutting", to cut and open nanostructures deposited on a nonplanar surface on a large scale. The feasibility of sodium-cutting was demonstrated with the successfully cutting open of ∼100% carbon nanospheres into nanobowls on a large scale from Sn@C nanospheres for the first time.

Multi-Criteria Analysis of Laser Cut Surface Characteristics in CO2 Laser Cutting of Stainless Steel

Directory of Open Access Journals (Sweden)

M. Radovanović

2015-06-01

Full Text Available In this paper an approach for multi-criteria analysis of laser cut surface characteristics using multi-criteria decision making (MCDM approach was presented. Laser cutting experiment was conducted based on Taguchi’s L27 experimental design by varying laser power, cutting speed, assist gas pressure and focus position at three levels. Multi-criteria analysis was performed by using the weighted aggregated sum product assessment (WASPAS method while considering burr height, drag line separation, depth of separation line, surface roughness and perpendicularity of the cut as assessment criteria. Based on conducted experimental investigation the MCDM model with 27 alternatives (laser cuts and five criteria was developed. The relative importance of criteria was determined by using pair-wise comparison matrix and geometric mean method of the analytic hierarchy process (AHP method.

Innovative on-site treatment cuts frac flowback water costs

Energy Technology Data Exchange (ETDEWEB)

NONE

2011-11-15

Water is an essential component of the drilling and hydraulic fracturing or fracking process and so the natural gas industry is a heavy user of water. Learning from other industries, gas producers are now employing mobile service providers with the latest integrated treatment systems (ITS) to clean flowback and produced water from fracturing operations at the wellhead. This paper presents a novel on-site treatment for frac water. ITS are pre-fabricated on moveable skids or a truck trailer with all the necessary controls, piping, valves, instrumentation, pumps, mixers and chemical injection modules. They remove oil and other hydrocarbons, suspended solids, and dissolved metals from the frac water using the tightly controlled chemistry, separation and filtration technology. This method can cut the average cost of treating produced water by 50%, simultaneously allowing drillers to maximize their efforts and manpower on generating oil and gas profits, rather than on water treatment.

Material testing of copper by extrusion-cutting

DEFF Research Database (Denmark)

Segalina, F.; De Chiffre, Leonardo

2017-01-01

was developed and implemented on a CNC lathe. An investigation was carried out extrusion-cutting copper discs using high-speed-steel cutting tools at 100 m/min cutting speed. Flow stress values for copper under machining-relevant conditions were obtained from measurement of the extrusion-cutting force...

Baikov-Lee representations of cut Feynman integrals

International Nuclear Information System (INIS)

Harley, Mark; Moriello, Francesco; Schabinger, Robert M.

2017-01-01

We develop a general framework for the evaluation of d-dimensional cut Feynman integrals based on the Baikov-Lee representation of purely-virtual Feynman integrals. We implement the generalized Cutkosky cutting rule using Cauchy’s residue theorem and identify a set of constraints which determine the integration domain. The method applies equally well to Feynman integrals with a unitarity cut in a single kinematic channel and to maximally-cut Feynman integrals. Our cut Baikov-Lee representation reproduces the expected relation between cuts and discontinuities in a given kinematic channel and furthermore makes the dependence on the kinematic variables manifest from the beginning. By combining the Baikov-Lee representation of maximally-cut Feynman integrals and the properties of periods of algebraic curves, we are able to obtain complete solution sets for the homogeneous differential equations satisfied by Feynman integrals which go beyond multiple polylogarithms. We apply our formalism to the direct evaluation of a number of interesting cut Feynman integrals.

Comparison of cutting efficiency with different diamond burs and water flow rates in cutting lithium disilicate glass ceramic.

Science.gov (United States)

Siegel, Sharon C; Patel, Tejas

2016-10-01

This study compared different diamond burs and different water flow rates on the cutting efficiency of sectioning through lithium disilicate glass ceramic. The authors used a standardized cutting regimen with 4 brands of diamond burs to section through lithium disilicate glass ceramic blocks. Twelve diamonds of each brand cut through the blocks in randomized order. In the first part of the study, the authors recorded sectioning rates in millimeters per minute for each diamond bur as a measure of cutting efficiency. In the second part of the study, the authors compared sectioning rates using only 1 brand of diamond bur, with 3 different water flow rates. The authors averaged and compared cutting rates of each brand of diamond bur and the cutting rates for each flow rate using an analysis of variance and determined the differences with a Tukey honest significant difference test. One diamond bur cut significantly slower than the other 3, and one diamond bur cut significantly faster than 2 of the others. The diamond bur cutting efficiency through lithium disilicate glass ceramic with a 20 mL/min water flow rate was significantly higher than 15 mL/min. There are differences in cutting efficiency between diamond burs when sectioning lithium disilicate glass ceramic. Use a minimum of 20 mL/min of water coolant flow when sectioning lithium disilicate glass ceramic with dental diamond burs to maximize cutting efficiency. Recommendations for specific diamond burs with a coarse grit and water flow rate of 20 mL/min can be made when removing or adjusting restorations made from lithium disilicate glass ceramic. Copyright © 2016 American Dental Association. Published by Elsevier Inc. All rights reserved.

Comparative study of 0° X-cut and Y + 36°-cut lithium niobate high-voltage sensing

International Nuclear Information System (INIS)

Patel, N.; Branch, D. W.; Cular, S.; Schamiloglu, E.

2015-01-01

A comparison study between Y + 36° and 0° X-cut lithium niobate (LiNbO 3 ) was performed to evaluate the influence of crystal cut on the acoustic propagation to realize a piezoelectric high-voltage sensor. The acoustic time-of-flight for each crystal cut was measured when applying direct current (DC), alternating current (AC), and pulsed voltages. Results show that the voltage-induced shift in the acoustic wave propagation time scaled quadratically with voltage for DC and AC voltages applied to X-cut crystals. For the Y + 36° crystal, the voltage-induced shift scales linearly with DC voltages and quadratically with AC voltages. When applying 5 μs voltage pulses to both crystals, the voltage-induced shift scaled linearly with voltage. For the Y + 36° cut, the voltage-induced shift from applying DC voltages ranged from 10 to 54 ps and 35 to 778 ps for AC voltages at 640 V over the frequency range of 100 Hz–100 kHz. Using the same conditions as the Y + 36° cut, the 0° X-cut crystal sensed a shift of 10–273 ps for DC voltages and 189–813 ps for AC voltage application. For 5 μs voltage pulses, the 0° X-cut crystal sensed a voltage induced shift of 0.250–2 ns and the Y + 36°-cut crystal sensed a time shift of 0.115–1.6 ns. This suggests a frequency sensitive response to voltage where the influence of the crystal cut was not a significant contributor under DC, AC, or pulsed voltage conditions. The measured DC data were compared to a 1-D impedance matrix model where the predicted incremental length changed as a function of voltage. When the voltage source error was eliminated through physical modeling from the uncertainty budget, the combined uncertainty of the sensor (within a 95% confidence interval) decreased to 0.0033% using a Y + 36°-cut crystal and 0.0032% using an X-cut crystal for all the voltage conditions used in this experiment

Underwater laser cutting of metallic structures

International Nuclear Information System (INIS)

Alfille, J.P.; Schildknecht, J.; Ramaswami, V.S.

1993-01-01

In the frame of an european contract, the feasibility of the underwater cutting with a CO 2 laser power is studied. The aim of this work is the dismantling metallic structures of reactors pools. The paper analyzes the general concept of the experimental device, the underwater cutting head, the experimenting vessel, examples of cuttings in dismantling situation with a 500 W CO 2 laser, and examples of cuttings with a 5 kW CO 2 laser. (author). 2 refs., 9 figs., 2 tabs

Theoretical aspects of fibre laser cutting

Energy Technology Data Exchange (ETDEWEB)

Mahrle, A; Beyer, E, E-mail: achim.mahrle@iws.fraunhofer.d [University of Technology Dresden, Institute for Surface and Manufacturing Technology, PO Box, 01062 Dresden (Germany)

2009-09-07

Fibre lasers offer distinct advantages over established laser systems with respect to power efficiency, beam guidance and beam quality. Consequently, the potential of these new laser beam sources will be increasingly exploited for laser cutting applications that are conventionally carried out with CO{sub 2} lasers. However, theoretical estimates of the effective absorptivity at the cut front suggest that the shorter wavelength of the fibre laser in combination with its high focusability seems to be primarily advantageous for thin sheet metal cutting whereas the CO{sub 2} laser is probably still capable of cutting thicker materials more efficiently. This surprising result is a consequence of the absorptivity behaviour of metals that shows essential quantitative differences for the corresponding wavelengths of both laser sources as a function of the angle of incidence between the laser beam and the material to be cut. In evaluation of the revealed dependences, solution strategies for an improvement of the efficiency of fibre laser cutting of thicker metal sheets are suggested.

A Numerical Approach and Comparison of Cutting Forces and Chip Morphology in Orthogonal Cutting of Light Alloys

International Nuclear Information System (INIS)

Alvarez, Roberto; Domingo, Rosario; Sebastian, Miguel Angel

2011-01-01

This paper deals with the simulation of UNS A92024 aluminium alloy cutting processes. In particular, 2D and 3D Finite Element Method (FEM) simulations were carried out in order to estimate cutting forces and chip morphology during turning operations. The material is modelled with two different set of parameters for the Johnson--Cook's (J-C) constitutive equation and a failure Cockroft and Latham's model exploited considers damage. The comparison between the predicted chip morphology and principal cutting forces at varying of J-C parameters and cutting regimes with those experimentally found are presented and discussed. The paper shows the importance of damage criterion in the cutting forces, during the simulation, especially in 3D.

Analysis of the influence of the cutting edge geometry on parameters of the perforation process for conveyor and transmission belts

Directory of Open Access Journals (Sweden)

Wojtkowiak Dominik

2018-01-01

Full Text Available Perforated belts, which are used in vacuum conveyor belts, can have significantly different mechanical properties like strength and elasticity due to a variety of used materials and can have different thickness from very thin (0,7 mm to thick belts (6 mm. In order to design a complex machine for mechanical perforation, which can perforate whole range of belts, it is necessary to research the influence of the cutting edge geometry on the parameters of the perforation process. Three most important parameters, which describe the perforation process are the cutting force, the velocity and the temperature of the piercing punch. The results presented in this paper consider two different types of punching (a piercing punch with the punching die or with the reducer plate and different cutting edge directions, angles, diameters and material properties. Test were made for different groups of composites belts – with polyurethane and polyester fabric, polyamide core or aramid-fibre reinforced polymers. The main goal of this research is to specify effective tools and parameters of the perforation process for each group of composites belts.

Laser cutting of sheets for Tailored Blanks

DEFF Research Database (Denmark)

Bagger, Claus; Olsen, Flemming Ove

1999-01-01

sound welds. Laser cutting the sheets may therefore be an alternative to shear cutting, if the cut kerf squareness can be kept below 0.05 mm.In a number of systematic laboratory experiments the effects of the major process parameters in laser cutting have been investigated. Each cut was quantified...... by the squareness, the surface roughness and the burr height. Mild steel as well as high strength steel with and with out galvanisation with thickness' of 0.7(5) and 1.25 were used.In the tests the difference in cut quality between a 5" and a 7.5" focusing lens were tested and the effect of using pulsed mode laser...

Cutting prepregs, cutting and processing polymer plastics in the manufacture of airсraft panels

OpenAIRE

MELUKHOV NIKITA; GRISHCHENKO TATIANA; LYUBUSHKIN VADIM

2017-01-01

The article presents an alternative to the solution of the problem of reduction of manual operations in manufacture. It may be achieved if cutting out prepregs and processing polymeric materials (PMP) be changed for sharp ultrasonic cutting when manufacturing components from polymeric composite materials (PCM). Described are the lines of investigations on new techniques of cutting out prepreg and processings polymeric material of the Nomex type with the use of the energy of ultrasonic waves. ...

Semantic Versus Syntactic Cutting Planes

OpenAIRE

Filmus, Yuval; Hrubeš, Pavel; Lauria, Massimo

2016-01-01

In this paper, we compare the strength of the semantic and syntactic version of the cutting planes proof system. First, we show that the lower bound technique of Pudlák applies also to semantic cutting planes: the proof system has feasible interpolation via monotone real circuits, which gives an exponential lower bound on lengths of semantic cutting planes refutations. Second, we show that semantic refutations are stronger than syntactic ones. In particular, we give a formula for whic...

21 CFR 882.4275 - Dowel cutting instrument.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Dowel cutting instrument. 882.4275 Section 882...) MEDICAL DEVICES NEUROLOGICAL DEVICES Neurological Surgical Devices § 882.4275 Dowel cutting instrument. (a) Identification. A dowel cutting instrument is a device used to cut dowels of bone for bone grafting. (b...

Hybrid Microsupercapacitors with Vertically Scaled 3D Current Collectors Fabricated using a Simple Cut-and-Transfer Strategy

KAUST Repository

Jiang, Qiu

2016-09-08

By employing 3D current collectors, hybrid coplanar microsupercapacitors are fabricated. These devices show excellent energy density of 200 μW h cm−2 compared to the state-of-the-art microsupercapacitors (1–40 μW h cm−2), and superior power density (4.4 mW cm−2) compared to thin film batteries and microbatteries at comparable energy density.

Hybrid Microsupercapacitors with Vertically Scaled 3D Current Collectors Fabricated using a Simple Cut-and-Transfer Strategy

KAUST Repository

Jiang, Qiu; Kurra, Narendra; Xia, Chuan; Alshareef, Husam N.

2016-01-01

By employing 3D current collectors, hybrid coplanar microsupercapacitors are fabricated. These devices show excellent energy density of 200 μW h cm−2 compared to the state-of-the-art microsupercapacitors (1–40 μW h cm−2), and superior power density (4.4 mW cm−2) compared to thin film batteries and microbatteries at comparable energy density.

High speed laser cutting machine. Kosoku reza kakoki

Energy Technology Data Exchange (ETDEWEB)

Shinno, N. (Matsushita Electric Industrial Co. Ltd., Kadoma, Osaka (Japan))

1993-11-01

The carbon dioxide gas laser cutting machine is being used widely for from cutting soft steel and stainless steel, etc. to intermetallic welding and in the field of cutting in particular, concerning sheet cutting, it has been changing the existing monopoly of the turret punch press, and as for medium and thick plate cutting, that of the gas plasma fusing device. This article is the general description of high speed laser cutting machine. Concerning the laser cutting (sheet cutting in particular), as the essential items for securing severe cutting accuracy and, at the same time, improving the cutting speed, the following matters are picked up for respective explanation; improvement of stationary machine accuracy, improvement of dynamic machine accuracy, improvement of quality of laser beam as well as optimization of cutting conditions, and shortening of piercing time. Also explanation is given to the respective items, namely speeding-up of medium and thick plate cutting, and reduction of load onto the operator by improved operation. Finally, feeding and removing of a sheet only, and feeding and removing with a pallet are mentioned as the efforts for automation and energy saving. 3 figs., 1 tab.

Improving rooting uniformity in rose cuttings

NARCIS (Netherlands)

Telgen, van H.J.; Eveleens-Clark, B.A.; Garcia Victoria, N.

2007-01-01

Studies to improve rooting uniformity of single node stem cuttings for rose are reported. We found that the variation in shoot growth in a young rose crop depended on the variation in root number of the cuttings, which, in turn, was related to the auxin concentration applied to the cutting before

Fabrication and characterization of DLC coated microdimples on hip prosthesis heads.

Science.gov (United States)

Choudhury, Dipankar; Ay Ching, Hee; Mamat, Azuddin Bin; Cizek, Jan; Abu Osman, Noor Azuan; Vrbka, Martin; Hartl, Martin; Krupka, Ivan

2015-07-01

Diamond like carbon (DLC) is applied as a thin film onto substrates to obtain desired surface properties such as increased hardness and corrosion resistance, and decreased friction and wear rate. Microdimple is an advanced surface modification technique enhancing the tribological performance. In this study, DLC coated microdimples were fabricated on hip prosthesis heads and their mechanical, material and surface properties were characterized. An Electro discharge machining (EDM) oriented microdrilling was utilized to fabricate a defined microdimple array (diameter of 300 µm, depth of 70 µm, and pitch of 900 µm) on stainless steel (SS) hip prosthesis heads. The dimpled surfaces were then coated by hydrogenated amorphous carbon (a-C:H) and tetrahedral amorphous carbon (Ta-C) layers by using a magnetron sputtering technology. A preliminary tribology test was conducted on these fabricated surfaces against a ceramic ball in simulated hip joint conditions. It was found that the fabricated dimples were perpendicular to the spherical surfaces and no cutting-tools wear debris was detected inside the individual dimples. The a-C:H and Ta-C coatings increased the hardness at both the dimple edges and the nondimpled region. The tribology test showed a significant reduction in friction coefficient for coated surfaces regardless of microdimple arrays: the lowest friction coefficient was found for the a-C:H samples (µ = 0.084), followed by Ta-C (µ = 0.119), as compared to the SS surface (µ = 0.248). © 2014 Wiley Periodicals, Inc.

Underwater laser cutting of metal structures

Energy Technology Data Exchange (ETDEWEB)

Alfille, J.P.; Prunele, D. de [CEA Centre d`Etudes de Saclay, 91 - Gif-sur-Yvette (France). Direction des Technologies Avancees; Pilot, G. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Dept. de Protection de l`Environnement et des Installations; Fredrick, P.; Ramaswami, V.S.; Muys, P. [Radius Engineering, Gent (Belgium)

1994-12-31

Cutting tests were carried out on stainless steel (304L) in air and under 7 meters of water (application to reactor pools), using CO{sub 2} and YAG lasers; results concerned cutting speed, quality of cut, cutting thickness. By-products of sectioning operations using a CO{sub 2} laser were studied: dross, aerosols, suspended particles in water, gas analysis, chemical analysis of the aerosols. Same measurements are currently being taken in the case of the YAG laser with beam transported via optical fiber. (from author). 16 figs., 2 tabs., 3 refs.

Underwater laser cutting of metal structures

International Nuclear Information System (INIS)

Alfille, J.P.; Prunele, D. de

1994-01-01

Cutting tests were carried out on stainless steel (304L) in air and under 7 meters of water (application to reactor pools), using CO 2 and YAG lasers; results concerned cutting speed, quality of cut, cutting thickness. By-products of sectioning operations using a CO 2 laser were studied: dross, aerosols, suspended particles in water, gas analysis, chemical analysis of the aerosols. Same measurements are currently being taken in the case of the YAG laser with beam transported via optical fiber. (from author). 16 figs., 2 tabs., 3 refs

The Effect of Muscle Fiber Direction on the Cut Surface Angle of Frozen Fish Muscular Tissue Cut by Bending Force

OpenAIRE

岡本, 清; 羽倉, 義雄; 鈴木, 寛一; 久保田, 清

1996-01-01

We have proposed a new cutting method named "Cryo-cutting" for frozen foodstuffs by applying a bending force instead of conventional cutting methods with band saw. This paper investigated the effect of muscle fiber angle (θf) to cut surface angle (θs) of frozen tuna muscular tissue at -70, -100 and -130°C for the purpose of evaluating the applicability of the cryo-cutting method to frozen fishes. The results were as follows : (1) There were two typical cutting patterns ("across the muscle fib...

Are the same tapes really the same? Ultrasound study of laser-cut and mechanically cut TVT-O post-operative behavior.

Science.gov (United States)

Rusavy, Zdenek; Masata, Jaromir; Svabik, Kamil; Hubka, Petr; Zvara, Karel; Martan, Alois

2017-11-25

TVT-O production has been modified to laser cutting from mechanical cutting. We compared the behavior of laser and mechanically cut tension-free vaginal tape-obturator (TVT-O) using ultrasound at various time points after surgery. This is a retrospective analysis of clinical and ultrasound data from two previously reported randomized controlled trials with TVT-O. Behavior of mechanically cut TVT-O implanted in January 2007 to November 2009 and laser-cut TVT-O implanted in May 2010 to May 2012 was assessed by ultrasound at day 1, the 2nd week, the 3rd month, and the 1st and 2nd years post-operatively. Bladder neck and tape margins positions were described by coordinates in the orthogonal system calculated from polar coordinates. Tape mobility was measured as a change in the upper and lower tape margin position from rest to maximal Valsalva. Comparison of 2-year subjective and objective surgery outcomes was also performed. In total, 68 mechanically cut and 50 laser-cut TVT-Os were implanted. Follow-up data were available from 49 and 45 women respectively. No differences in any baseline characteristics or bladder neck mobility were observed. Significantly lower tape mobility was observed on day 1 and week 2 after mechanically cut TVT-O, although subsequent mobility was comparable to laser-cut TVT-O. The subjective and objective surgery outcomes were comparable. Although without clinical significance, early postoperative behavior of the mechanically cut and laser-cut TVT-O tapes differs. The less stiff, mechanically-cut TVT-O loosens within 2 weeks of implantation, whereas the stiffer, laser-cut TVT-O keeps its tension.

Effects of cutting and maturity on lycopene concentration of fresh-cut tomatoes during storage at different temperatures

NARCIS (Netherlands)

Moreira Lana, M.; Dekker, M.; Linssen, R.F.A.; Kooten, van O.

2005-01-01

To investigate the changes in lycopene concentration of fresh-cut tomato during storage, tomato fruits at different stages of maturity were cut into 7 mm slices and stored at temperatures varying from 2°C to 16°C. To assess the effect of cutting, intact fruit were stored in an additional experiment

Underwater plasma arc cutting

International Nuclear Information System (INIS)

Leautier, R.; Pilot, G.

1991-01-01

This report describes the work done to develop underwater plasma arc cutting techniques, to characterise aerosols from cutting operations on radioactive and non-radioactive work-pieces, and to develop suitable ventilation and filtration techniques. The work has been carried out in the framework of a contract between CEA-CEN Cadarache and the Commission of European Communities. Furthermore, this work has been carried out in close cooperation with CEA-CEN Saclay mainly for secondary emissions and radioactive analysis. The contract started in May 1986 and was completed in December 1988 by a supplementary agreement. This report has been compiled from several progress reports submitted during the work period, contains the main findings of the work and encloses the results of comparative tests on plasma arc cutting

Turbine airfoil fabricated from tapered extrusions

Science.gov (United States)

Marra, John J

2013-07-16

An airfoil (30) and fabrication process for turbine blades with cooling channels (26). Tapered tubes (32A-32D) are bonded together in a parallel sequence, forming a leading edge (21), a trailing edge (22), and pressure and suction side walls (23, 24) connected by internal ribs (25). The tapered tubes may be extruded without camber to simplify the extrusion process, then bonded along matching surfaces (34), forming a non-cambered airfoil (28), which may be cambered in a hot forming process and cut (48) to length. The tubes may have tapered walls that are thinner at the blade tip (T1) than at the base (T2), reducing mass. A cap (50) may be attached to the blade tip. A mounting lug (58) may be forged (60) on the airfoil base and then machined, completing the blade for mounting in a turbine rotor disk.

New stratigraphic, chronologic, and magnetic fabric constraints for Neogene and Quaternary ignimbrites in the Central Andes (South Peru)

Science.gov (United States)

De La Rupelle, A.; Thouret, J. C.; Cubukcu, H. E.; Jicha, B.; Bréard, E.; Gerbe, M.-C.; Le Pennec, J.-L.; Diot, H.; Boivin, P.

2012-04-01

Central Andean deformation history in southern Peru is recorded in Neogene volcanic units of Ocoña and Cotahuasi canyons that cut across the western Cordillera. Acceleration (100 km3) Nazca (c.24.6 Ma), Alpabamba (19.4-18.0 Ma), and Huaylillas (14.25-12.7 Ma) ignimbrite sheets preceded the canyon incision, whereas sheets of smaller volume (Peru, stratigraphy, chronology, AMS, fabric, Neogene, Quaternary.

Modified GrabCut for human face segmentation

Directory of Open Access Journals (Sweden)

Dina Khattab

2014-12-01

Full Text Available GrabCut is a segmentation technique for 2D still color images, which is mainly based on an iterative energy minimization. The energy function of the GrabCut optimization algorithm is based mainly on a probabilistic model for pixel color distribution. Therefore, GrabCut may introduce unacceptable results in the cases of low contrast between foreground and background colors. In this manner, this paper presents a modified GrabCut technique for the segmentation of human faces from images of full humans. The modified technique introduces a new face location model for the energy minimization function of the GrabCut, in addition to the existing color one. This location model considers the distance distribution of the pixels from the silhouette boundary of a fitted head, of a 3D morphable model, to the image. The experimental results of the modified GrabCut have demonstrated better segmentation robustness and accuracy compared to the original GrabCut for human face segmentation.

Analysis of key factors influencing the evaporation performances of an oriented linear cutting copper fiber sintered felt

Science.gov (United States)

Pan, Minqiang; Zhong, Yujian

2018-01-01

Porous structure can effectively enhance the heat transfer efficiency. A kind of micro vaporizer using the oriented linear cutting copper fiber sintered felt is proposed in this work. Multiple long cutting copper fibers are firstly fabricated with a multi-tooth tool and then sintered together in parallel to form uniform thickness metal fiber sintered felts that provided a characteristic of oriented microchannels. The temperature rise response and thermal conversion efficiency are experimentally investigated to evaluate the influences of porosity, surface structure, feed flow rate and input power on the evaporation characteristics. It is indicated that the temperature rise response of water is mainly affected by input power and feed flow rate. High input power and low feed flow rate present better temperature rise response of water. Porosity rather than surface structure plays an important role in the temperature rise response of water at a relatively high input power. The thermal conversion efficiency is dominated by the input power and surface structure. The oriented linear cutting copper fiber sintered felts for three kinds of porosities show better thermal conversion efficiency than that of the oriented linear copper wire sintered felt when the input power is less than 115 W. All the sintered felts have almost the same performance of thermal conversion at a high input power.

Materials selection for cutting tools

International Nuclear Information System (INIS)

Burkhis, Adel M.

2008-01-01

The selection of proper tool steel for a given application is a difficult task. So; the most important selection factors in choosing cutting tool materials are based on their tool material requirements, cutting tool design and service conditions which is mainly considered as functional requirements. The processability requirements concerns in heat treat ability of the material tool. The classification of these tool materials were discussed with their properties requirement and percent of alloying element which is added to give best properties with a little increase in cost that highly appear in comparison of the selection. The cutting tool materials were evaluated based on two cases; The first was in case of rough surface; the high speed steels is the best material and the other was the ceramic material is the highest performance in cutting of soft or high rate of metal removal. (author)

Ductile cutting of silicon microstructures with surface inclination measurement and compensation by using a force sensor integrated single point diamond tool

International Nuclear Information System (INIS)

Chen, Yuan-Liu; Cai, Yindi; Shimizu, Yuki; Ito, So; Gao, Wei; Ju, Bing-Feng

2016-01-01

This paper presents a measurement and compensation method of surface inclination for ductile cutting of silicon microstructures by using a diamond tool with a force sensor based on a four-axis ultra-precision lathe. The X- and Y-directional inclinations of a single crystal silicon workpiece with respect to the X- and Y-motion axes of the lathe slides were measured respectively by employing the diamond tool as a touch-trigger probe, in which the tool-workpiece contact is sensitively detected by monitoring the force sensor output. Based on the measurement results, fabrication of silicon microstructures can be thus carried out directly along the tilted silicon workpiece by compensating the cutting motion axis to be parallel to the silicon surface without time-consuming pre-adjustment of the surface inclination or turning of a flat surface. A diamond tool with a negative rake angle was used in the experiment for superior ductile cutting performance. The measurement precision by using the diamond tool as a touch-trigger probe was investigated. Experiments of surface inclination measurement and ultra-precision ductile cutting of a micro-pillar array and a micro-pyramid array with inclination compensation were carried out respectively to demonstrate the feasibility of the proposed method. (paper)

Edge Cut Domination, Irredundance, and Independence in Graphs

OpenAIRE

Fenstermacher, Todd; Hedetniemi, Stephen; Laskar, Renu

2016-01-01

An edge dominating set $F$ of a graph $G=(V,E)$ is an \\textit{edge cut dominating set} if the subgraph $\\langle V,G-F \\rangle$ is disconnected. The \\textit{edge cut domination number} $\\gamma_{ct}(G)$ of $G$ is the minimum cardinality of an edge cut dominating set of $G.$ In this paper we study the edge cut domination number and investigate its relationships with other parameters of graphs. We also introduce the properties edge cut irredundance and edge cut independence.

Preferences of cut flowers consumers

Directory of Open Access Journals (Sweden)

Sylwia Kierczyńska

2010-01-01

Full Text Available The results of interviews suggest that majority of the cut flowers’ consumers has favourite kind of flower, among which most frequently pointed one was the rose. More than half of the interviewed favour the uniform colour of cut flowers and red colour was the most favourite one. The subtle smell of flowers was the most preferable one but the intensive fragrance was favoured for more consumers than odourless flowers. The data from selected florists’ confirm the information from interviews – in spite of the occasion, roses were the most demanded cut flowers.

Status on underwater plasma arc cutting in KHI, 3

International Nuclear Information System (INIS)

Abe, Tadashi; Aota, Toshiichi; Nishizaki, Tadashi; Nakayama, Shigeru; Yamashita, Seiji

1983-01-01

In Kawasaki Heavy Industries, Ltd., the development of a remote dismantling system by underwater plasma arc cutting process has been advanced, expecting its application to the dismantling and removal of nuclear reactor facilities. In the previous two reports, the fundamental experimental results such as the comparison of the cutting capability in air and in water were shown, but this time, the remote automatic cutting of wedge-shaped specimens was carried out, using a newly installed manipulator for underwater works, therefore its outline is reported. Also the cutting experiment by overhead position and vertical position was performed by using the same equipment, and comparison was made with the cutting capability by downhand and horizontal positions. It is important to grasp the cutting characteristics in the case of upward advancing and downward advancing cuttings by overhead and vertical positions when the cutting of pressure vessels and horizontal pipes into rings is supposed. The experimental apparatus, the cutting conditions, the testing method and the test results of the cutting capability test, the test of changing direction during cutting, and the remote cutting of pipes into rings are described. The underwater plasma arc cutting can cut all metals, the cutting speed is relatively high, and the apparatus is simple and compact. (Kako, I.)

MECHANISMS OF CUTTING BLADE WEAR AND THEIR INFLUENCE ON CUTTING ABILITY OF THE TOOL DURING MACHINING OF SPECIAL ALLOYS

Directory of Open Access Journals (Sweden)

Tomáš Zlámal

2016-09-01

Full Text Available With increased requirements for quality and shelf life of machined parts there is also a higher share of the use of material with specific properties that are identified by the term “superalloys”. These materials differ from common steels by mechanical and physical properties that cause their worse machinability. During machining of “superalloys” worse machinability has negative influence primarily on the amount of cutting edge wear, which shortens durability of the cutting tool. The goal of experimental activity shown in this contribution is to determine individual mechanisms of the cutting edge wear and their effects on the cutting ability during high speed machining of nickel superalloy. A specific exchangeable cutting insert made from cubic boric nitride was used for machining of the 625 material according to ASM 5666F. The criteria to evaluate cutting ability and durability of the cutting tool became selected parameters of surface integrity and quality of the machined surface.

Submerged cutting characteristics of abrasive suspension jet

International Nuclear Information System (INIS)

Shimizu, Seiji; Peng, Guoyi; Oguma, Yasuyuki; Nishikata, Hiroki

2015-01-01

An abrasive suspension jet (ASJ) formed by propelling abrasive suspension through a nozzle has a greater cutting capability than the conventional abrasive water jet. However the cutting capability of submerged ASJs decreases drastically with increasing the standoff distance and the pressure around the jet. A sheathed nozzle nozzle with ventilation for ASJs has been developed as a mean of extending the effective stand-off distance and improving the cutting capabilities under submerged condition. In the present investigation, cutting tests by ASJs in air and under submerged condition are conducted with specimens of aluminum alloy. Air coated ASJs are formed by using a sheathed nozzle with ventilation. The relative cutting depth is defined as the cutting depth is arranged effectually by the cavitation number based on the cavity pressure measured at the sheath. (author)

Ann modeling of kerf transfer in Co2 laser cutting and optimization of cutting parameters using monte carlo method

Directory of Open Access Journals (Sweden)

Miloš Madić

2015-01-01

Full Text Available In this paper, an attempt has been made to develop a mathematical model in order to study the relationship between laser cutting parameters such as laser power, cutting speed, assist gas pressure and focus position, and kerf taper angle obtained in CO2 laser cutting of AISI 304 stainless steel. To this aim, a single hidden layer artificial neural network (ANN trained with gradient descent with momentum algorithm was used. To obtain an experimental database for the ANN training, laser cutting experiment was planned as per Taguchi’s L27 orthogonal array with three levels for each of the cutting parameters. Statistically assessed as adequate, ANN model was then used to investigate the effect of the laser cutting parameters on the kerf taper angle by generating 2D and 3D plots. It was observed that the kerf taper angle was highly sensitive to the selected laser cutting parameters, as well as their interactions. In addition to modeling, by applying the Monte Carlo method on the developed kerf taper angle ANN model, the near optimal laser cutting parameter settings, which minimize kerf taper angle, were determined.

The effects of cutting parameters on cutting forces and heat generation when drilling animal bone and biomechanical test materials.

Science.gov (United States)

Cseke, Akos; Heinemann, Robert

2018-01-01

The research presented in this paper investigated the effects of spindle speed and feed rate on the resultant cutting forces (thrust force and torque) and temperatures while drilling SawBones ® biomechanical test materials and cadaveric cortical bone (bovine and porcine femur) specimens. It also investigated cortical bone anisotropy on the cutting forces, when drilling in axial and radial directions. The cutting forces are only affected by the feed rate, whereas the cutting temperature in contrast is affected by both spindle speed and feed rate. The temperature distribution indicates friction as the primary heat source, which is caused by the rubbing of the tool margins and the already cut chips over the borehole wall. Cutting forces were considerably higher when drilling animal cortical bone, in comparison to cortical test material. Drilling direction, and therewith anisotropy, appears to have a negligible effect on the cutting forces. The results suggest that this can be attributed to the osteons being cut at an angle rather than in purely axial or radial direction, as a result of a twist drill's point angle. Copyright © 2017 IPEM. Published by Elsevier Ltd. All rights reserved.

Fabrication of an Anisotropic Superhydrophobic Polymer Surface Using Compression Molding and Dip Coating

Directory of Open Access Journals (Sweden)

Kyong-Min Lee

2017-11-01

Full Text Available Many studies of anisotropic wetting surfaces with directional structures inspired from rice leaves, bamboo leaves, and butterfly wings have been carried out because of their unique liquid shape control and transportation. In this study, a precision mechanical cutting process, ultra-precision machining using a single crystal diamond tool, was used to fabricate a mold with microscale directional patterns of triangular cross-sectional shape for good moldability, and the patterns were duplicated on a flat thermoplastic polymer plate by compression molding for the mass production of an anisotropic wetting polymer surface. Anisotropic wetting was observed only with microscale patterns, but the sliding of water could not be achieved because of the pinning effect of the micro-structure. Therefore, an additional dip coating process with 1H, 1H, 2H, 2H-perfluorodecythricholosilanes, and TiO2 nanoparticles was applied for a small sliding angle with nanoscale patterns and a low surface energy. The anisotropic superhydrophobic surface was fabricated and the surface morphology and anisotropic wetting behaviors were investigated. The suggested fabrication method can be used to mass produce an anisotropic superhydrophobic polymer surface, demonstrating the feasibility of liquid shape control and transportation.

Evaluation of cutting force uncertainty components in turning

DEFF Research Database (Denmark)

Axinte, Dragos Aurelian; Belluco, Walter; De Chiffre, Leonardo

2000-01-01

A procedure is proposed for the evaluation of those uncertainty components of a single cutting force measurement in turning that are related to the contributions of the dynamometer calibration and the cutting process itself. Based on an empirical model including errors form both sources......, the uncertainty for a single measurement of cutting force is presented, and expressions for the expected uncertainty vs. cutting parameters are proposed. This approach gives the possibility of evaluating cutting force uncertainty components in turning, for a defined range of cutting parameters, based on few...

Identification of the critical depth-of-cut through a 2D image of the cutting region resulting from taper cutting of brittle materials

Science.gov (United States)

Gu, Wen; Zhu, Zhiwei; Zhu, Wu-Le; Lu, Leyao; To, Suet; Xiao, Gaobo

2018-05-01

An automatic identification method for obtaining the critical depth-of-cut (DoC) of brittle materials with nanometric accuracy and sub-nanometric uncertainty is proposed in this paper. With this method, a two-dimensional (2D) microscopic image of the taper cutting region is captured and further processed by image analysis to extract the margin of generated micro-cracks in the imaging plane. Meanwhile, an analytical model is formulated to describe the theoretical curve of the projected cutting points on the imaging plane with respect to a specified DoC during the whole cutting process. By adopting differential evolution algorithm-based minimization, the critical DoC can be identified by minimizing the deviation between the extracted margin and the theoretical curve. The proposed method is demonstrated through both numerical simulation and experimental analysis. Compared with conventional 2D- and 3D-microscopic-image-based methods, determination of the critical DoC in this study uses the envelope profile rather than the onset point of the generated cracks, providing a more objective approach with smaller uncertainty.

Cutting tool for removing materials from well bore

International Nuclear Information System (INIS)

Lynde, G.D.; Harvey, H.H. Jr.

1991-01-01

This patent describes a cutting tool adapted to be positioned downhole in a well bore for removing a metal member from the well bore; a tool body adapted to be received within said well bore and to be supported at its upper end for rotation about a longitudinal axis; blades at spaced intervals on the body and extending outwardly therefrom, each of the blades having a base with a leading surface relative to the direction of rotation; closely spaced cutting elements of hard cutting material secured to said leading surface of the base in a plurality of transversely extending rows, each cutting element being of a predetermined size and shape and arranged in a predetermined generally symmetrical pattern on the base relative to the other elements, each of said cutting elements having an exposed from cutting face forming a cutting surface, a rear face secured to the leading surface of said base, a peripheral surface extending between said faces, and a relatively sharp edge formed at the juncture of the front face and peripheral surface; the front cutting face of each cutting element being arranged and constructed for directing an extending end portion of a turning cut form said member to effect a breaking of said turning from the member being cut in a predetermined manner to minimize interesting of the turning

Craterlike structures on the laser cut surface

Science.gov (United States)

Shulyatyev, V. B.; Orishich, A. M.

2017-10-01

Analysis of the laser cut surface morphology remain topical. It is related with the fact that the surface roughness is the main index of the cut quality. The present paper deals with the experimental study of the relatively unstudied type of defects on the laser cut surface, dimples, or craters. According to the measurement results, amount of craters per unit of the laser cut surface area rises as the sheet thickness rises. The crater diameter rises together with the sheet thickness and distance from the upper sheet edge. The obtained data permit concluding that the defects like craters are observed predominantly in the case of thick sheets. The results agree with the hypothesis of crater formation as impact structures resulting from the melt drops getting on the cut channel walls upon separation from the cut front by the gas flow.

Low cost, p-ZnO/n-Si, rectifying, nano heterojunction diode: Fabrication and electrical characterization

Directory of Open Access Journals (Sweden)

Vinay Kabra

2014-11-01

Full Text Available A low cost, highly rectifying, nano heterojunction (p-ZnO/n-Si diode was fabricated using solution-processed, p-type, ZnO nanoparticles and an n-type Si substrate. p-type ZnO nanoparticles were synthesized using a chemical synthesis route and characterized by XRD and a Hall effect measurement system. The device was fabricated by forming thin film of synthesized p-ZnO nanoparticles on an n-Si substrate using a dip coating technique. The device was then characterized by current–voltage (I–V and capacitance–voltage (C–V measurements. The effect of UV illumination on the I–V characteristics was also explored and indicated the formation of a highly rectifying, nano heterojunction with a rectification ratio of 101 at 3 V, which increased nearly 2.5 times (232 at 3 V under UV illumination. However, the cut-in voltage decreases from 1.5 V to 0.9 V under UV illumination. The fabricated device could be used in switches, rectifiers, clipper and clamper circuits, BJTs, MOSFETs and other electronic circuitry.

The Gesso Cut for Printmaking

Science.gov (United States)

Kelly, Perry; Sarvis, Alva

1969-01-01

Directions are given for the preparation, cutting, and printing of a gesso board. A gesso cut is defined as a board coated with gesso into which a design has been impressed. The process is similar to the woodcut, but offers greater textural possibilities. (BF)

Laser cutting of Kevlar laminates

Energy Technology Data Exchange (ETDEWEB)

VanCleave, R.A.

1977-09-01

An investigation has been conducted of the use of laser energy for cutting contours, diameters, and holes in flat and shaped Kevlar 49 fiber-reinforced epoxy laminates as an alternate to conventional machining. The investigation has shown that flat laminates 6.35 mm thick may be cut without backup by using a high-powered (1000-watt) continuous wave CO/sub 2/ laser at high feedrates (33.87 mm per second). The cut produced was free of the burrs and delaminations resulting from conventional machining methods without intimate contact backup. In addition, the process cycle time was greatly reduced.

Investigation of cutting-induced damage in CMC bend bars

Directory of Open Access Journals (Sweden)

Neubrand A.

2015-01-01

Full Text Available Ceramic matrix composites (“CMC” with a strong fibre-matrix interface can be made damage-tolerant by introducing a highly porous matrix. Such composites typically have only a low interlaminar shear strength, which can potentially promote damage when preparing specimens or components by cutting. In order to investigate the damage induced by different cutting methods, waterjet cutting with and without abrasives, laser-cutting, wire eroding and cutoff grinding were used to cut plates of two different CMCs with a matrix porosity up to 35 vol.-%. For each combination of cutting method and composite, the flexural and interlaminar shear strength of the resulting specimens was determined. Additionally, the integrity of the regions near the cut surfaces was investigated by high-resolution x-ray computer tomography. It could be shown that the geometrical quality of the cut is strongly affected by the cutting method employed. Laser cut and waterjet cut specimens showed damage and delaminations near the cut surface leading to a reduced interlaminar shear strength of short bend bars in extreme cases.

Investigation of Cutting Quality of Remote DOE Laser Cutting in 0.5 mm Stainless Steel

Science.gov (United States)

Villumsen, Sigurd Lazic; Kristiansen, Morten

It has previously been shown that the stability of the remote fusion cutting (RFC) process can be increased by modifying the intensity profile of the laser by means of a diffractive optical element (DOE). This paper investigates the quality of remote DOE cutting (RDC) conducted with a 3 kW single mode fiber laser in 0.5 mm stainless steel. An automatic measurement system is used to investigate how the travel speed, focus offset and angle of incidence effect the kerf width and kerf variance. The study shows that the RDC process has a very low kerf width variance, and that the kerf width decreases with cutting speed. Furthermore, selected etched samples show a significant increase in the perpendicularity of the cuts when compared to RFC. Also, on average, the depth of the layer of molten material for RFC is 83% deeper than for RDC.

Fabrication of a Cryogenic Bias Filter for Ultrasensitive Focal Plane

Science.gov (United States)

Chervenak, James; Wollack, Edward

2012-01-01

A fabrication process has been developed for cryogenic in-line filtering for the bias and readout of ultrasensitive cryogenic bolometers for millimeter and submillimeter wavelengths. The design is a microstripline filter that cuts out, or strongly attenuates, frequencies (10 50 GHz) that can be carried by wiring staged at cryogenic temperatures. The filter must have 100-percent transmission at DC and low frequencies where the bias and readout lines will carry signal. The fabrication requires the encapsulation of superconducting wiring in a dielectric-metal envelope with precise electrical characteristics. Sufficiently thick insulation layers with high-conductivity metal layers fully surrounding a patterned superconducting wire in arrayable formats have been demonstrated. A degenerately doped silicon wafer has been chosen to provide a metallic ground plane. A metallic seed layer is patterned to enable attachment to the ground plane. Thick silicon dioxide films are deposited at low temperatures to provide tunable dielectric isolation without degrading the metallic seed layer. Superconducting wiring is deposited and patterned using microstripline filtering techniques to cut out the relevant frequencies. A low Tc superconductor is used so that it will attenuate power strongly above the gap frequency. Thick dielectric is deposited on top of the circuit, and then vias are patterned through both dielectric layers. A thick conductive film is deposited conformally over the entire circuit, except for the contact pads for the signal and bias attachments to complete the encapsulating ground plane. Filters are high-aspect- ratio rectangles, allowing close packing in one direction, while enabling the chip to feed through the wall of a copper enclosure. The chip is secured in the copper wall using a soft metal seal to make good thermal and electrical contact to the outer shield.

High precision tungsten cutting for optics

International Nuclear Information System (INIS)

Reglero, V.; Velasco, T.; Rodrigo, J.; Gasent, L.J.; Alamo, J.; Chato, R.; Ruiz Urien, I.; Santos, I.; Zarauz, J.; Clemente, G.; Sanz-Tudanca, C.; Lopez, J.L.

2001-01-01

The results obtained during the INTEGRAL masks development program an implementing the HURA and MURA codes on tungsten plates of different thickness are presented. Hard scientific requirements on pixels size and location tolerances (tenths of microns over large areas -1 m 2 - and thickness from 0.5 mm to 60 mm) required the set up of a dedicated program for testing cutting technologies: laser, photochemical milling, spark machining and electro discharge wire cutting. After a very intensive test campaign the wire cutting process was selected as the optimum technology for code manufacturing . Accuracies achieved an the code cutting fulfill scientific requirements. In fact, they are 5 times better than required. Pixel size and centroids location accuracies of 0.01 mm over a 1 m 2 area have been obtained for the 10,000 pixels on IBIS, 100 pixels on SPI and 24000 pixels on JEM-X masks. Comparative results among different cutting technologies are also discussed. (author)

Development of laser cutting method for stainless steel liner

International Nuclear Information System (INIS)

Ishihara, Satoshi; Takahata, Masato; Wignarajah, Sivakumaran; Kamata, Hirofumi

2007-01-01

The present work is an attempt to develop a laser cutting method for cutting and removing stainless steel liners from concrete walls and floors in nuclear facilities. The effect of basic laser cutting parameters such as energy, cutting speed, assist gas flow etc. were first studied through cutting experiments on mock-up concrete specimens lined with 3mm thick stainless steel sheets using a 1kW Nd:YAG laser. These initial studies were followed by further studies on the effect of unevenness of the liner surface and on a new method of confining contamination during the cutting process using a sliding evacuation hood attached to the laser cutting head. The results showed that laser cutting is superior to other conventional cutting methods from the point of view of safety from radioactivity and work efficiency when cutting contaminated stainless steel liners. (author)

Regge cuts: A general approach

International Nuclear Information System (INIS)

Weis, J.H.

1976-01-01

We discuss an approach to the calculation of Regge-cut contributions to scattering amplitudes which relies only on the general structure of the physical Reggeon couplings. It thus allows a unified treatment of disparate models [such as the Feynman (Mandelstam) graph model and the dual model] and a general derivation of the Abramovskii--Gribov--Kancheli (AGK) rules. The structure of the Reggeon couplings is expressed through integrals over complex helicity. The Regge-cut amplitude can then be obtained, and its s-channel discontinuity, taken; there results a direct derivation of a set of ''cutting rules'' which express the total discontinuity as a sum of terms involving various discontinuities of the Reggeon couplings. The equality of these discontinuities follows directly if the singularities in complex helicity are the usual ones. Thus the AGK rules are seen to be quite model independent. Here we study in detail the simplest example: the Reggeon-particle cut in the four-particle amplitude

Why I like power cuts...

CERN Multimedia

Computer Security Team

2012-01-01

Accidental power cuts - a permanent nuisance when running accelerators or computing services, since it takes a lot of time to recover from them. While I feel very sorry for those who are under pressure to get their service running again and deeply regret the loss of down-time and availability, I must admit that I like power cuts: power cuts make computers reboot! And rebooting computers at CERN means all the pending software patches are automatically applied.   But don’t think I am egotistic enough to endorse power cuts. Not necessarily! I am already happy if you regularly patch your computer(s) yourself, where regularly means at least once a month: · If you run a centrally or locally managed Windows computer, give that small orange blinking “CMF” icon in the taskbar a chance in the evening to apply all the pending patches. Also, let it initiate a reboot at the end! · If you have a personal computer with your own Windows operating system, ...

Method of dismantling cylindrical structure by cutting

International Nuclear Information System (INIS)

Harada, Minoru; Mitsuo, Kohei; Yokota, Isoya; Nakamura, Kenjiro.

1989-01-01

This invention concerns a method of cutting and removing cylindrical structures, for example, iron-reinforced concrete materials such as thermal shielding walls in BWR type power plants into block-like form. That is, in a method of cutting and removing the cylindrical structure from the side of the outer wall, the structural material is cut from above to below successively in the axial direction and the circumferential direction by means abrasive jet by remote operation and cut into blocks each of a predetermined size. The cut out blocks are successively taken out. Cutting of the material from above to below by remote operation and taking out of small blocks causes no hazards to human body. Upon practicing the present invention, it is preferred to use a processing device for slurry and exhaust gases for preventing scattering of activated dismantled pieces or powdery dusts. (K.M.)

Nuclear fuel control in fuel fabrication plants

International Nuclear Information System (INIS)

Seki, Yoshitatsu

1976-01-01

The basic control problems of measuring uranium and of the environment inside and outside nuclear fuel fabrication plants are reviewed, excluding criticality prevention in case of submergence. The occurrence of loss scraps in fabrication and scrap-recycling, the measuring error, the uranium going cut of the system, the confirmation of the presence of lost uranium and the requirement of the measurement control for safeguard make the measurement control very complicated. The establishment of MBA (material balance area) and ICA (item control area) can make clearer the control of inventories, the control of loss scraps and the control of measuring points. Besides the above basic points, the following points are to be taken into account: 1) the method of confirmation of inventories, 2) the introduction of reliable NDT instruments for the rapid check system for enrichment and amount of uranium, 3) the introduction of real time system, and 4) the clarification of MUF analysis and its application to the reliability check of measurement control system. The environment control includes the controls of the uranium concentration in factory atmosphere, the surface contamination, the space dose rate, the uranium concentration in air and water discharged from factories, and the uranium in liquid wastes. The future problems are the practical restudy of measurement control under NPT, the definite plan of burglary protection and the realization of the disposal of solid wastes. (Iwakiri, K.)

Photodiode-based cutting interruption sensor for near-infrared lasers.

Science.gov (United States)

Adelmann, B; Schleier, M; Neumeier, B; Hellmann, R

2016-03-01

We report on a photodiode-based sensor system to detect cutting interruptions during laser cutting with a fiber laser. An InGaAs diode records the thermal radiation from the process zone with a ring mirror and optical filter arrangement mounted between a collimation unit and a cutting head. The photodiode current is digitalized with a sample rate of 20 kHz and filtered with a Chebyshev Type I filter. From the measured signal during the piercing, a threshold value is calculated. When the diode signal exceeds this threshold during cutting, a cutting interruption is indicated. This method is applied to sensor signals from cutting mild steel, stainless steel, and aluminum, as well as different material thicknesses and also laser flame cutting, showing the possibility to detect cutting interruptions in a broad variety of applications. In a series of 83 incomplete cuts, every cutting interruption is successfully detected (alpha error of 0%), while no cutting interruption is reported in 266 complete cuts (beta error of 0%). With this remarkable high detection rate and low error rate, the possibility to work with different materials and thicknesses in combination with the easy mounting of the sensor unit also to existing cutting machines highlight the enormous potential for this sensor system in industrial applications.

Users' manual for fault tree analysis code: CUT-TD

International Nuclear Information System (INIS)

Watanabe, Norio; Kiyota, Mikio.

1992-06-01

The CUT-TD code has been developed to find minimal cut sets for a given fault tree and to calculate the occurrence probability of its top event. This code uses an improved top-down algorithm which can enhance the efficiency in deriving minimal cut sets. The features in processing techniques incorporated into CUT-TD are as follows: (1) Consecutive OR gates or consecutive AND gates can be coalesced into a single gate. As a result, this processing directly produces cut sets for the redefined single gate with each gate not being developed. (2) The independent subtrees are automatically identified and their respective cut sets are separately found to enhance the efficiency in processing. (3) The minimal cut sets can be obtained for the top event of a fault tree by combining their respective minimal cut sets for several gates of the fault tree. (4) The user can reduce the computing time for finding minimal cut sets and control the size and significance of cut sets by inputting a minimum probability cut off and/or a maximum order cut off. (5) The user can select events that need not to be further developed in the process of obtaining minimal cut sets. This option can reduce the number of minimal cut sets, save the computing time and assists the user in reviewing the result. (6) Computing time is monitored by the CUT-TD code so that it can prevent the running job from abnormally ending due to excessive CPU time and produce an intermediate result. The CUT-TD code has the ability to restart the calculation with use of the intermediate result. This report provides a users' manual for the CUT-TD code. (author)

Monitoring machining conditions by analyzing cutting force vibration

Energy Technology Data Exchange (ETDEWEB)

Piao, Chun Guang; Kim, Ju Wan; Kim, Jin Oh; Shin, Yoan [Soongsl University, Seoul (Korea, Republic of)

2015-09-15

This paper deals with an experimental technique for monitoring machining conditions by analyzing cutting-force vibration measured at a milling machine. This technique is based on the relationship of the cutting-force vibrations with the feed rate and cutting depth as reported earlier. The measurement system consists of dynamic force transducers and a signal amplifier. The analysis system includes an oscilloscope and a computer with a LabVIEW program. Experiments were carried out at various feed rates and cutting depths, while the rotating speed was kept constant. The magnitude of the cutting force vibration component corresponding to the number of cutting edges multiplied by the frequency of rotation was linearly correlated with the machining conditions. When one condition of machining is known, another condition can be identified by analyzing the cutting-force vibration.

Monitoring machining conditions by analyzing cutting force vibration

International Nuclear Information System (INIS)

Piao, Chun Guang; Kim, Ju Wan; Kim, Jin Oh; Shin, Yoan

2015-01-01

This paper deals with an experimental technique for monitoring machining conditions by analyzing cutting-force vibration measured at a milling machine. This technique is based on the relationship of the cutting-force vibrations with the feed rate and cutting depth as reported earlier. The measurement system consists of dynamic force transducers and a signal amplifier. The analysis system includes an oscilloscope and a computer with a LabVIEW program. Experiments were carried out at various feed rates and cutting depths, while the rotating speed was kept constant. The magnitude of the cutting force vibration component corresponding to the number of cutting edges multiplied by the frequency of rotation was linearly correlated with the machining conditions. When one condition of machining is known, another condition can be identified by analyzing the cutting-force vibration

Melt Flow and Energy Limitation of Laser Cutting

Directory of Open Access Journals (Sweden)

Pavel Hudeček

2016-01-01

Full Text Available Laser technology is a convertible technology for plenty of parts in most materials. Laser material processing for industrial manufacturing applications is today a widespread procedure for welding, cutting, marking and micro machining of metal and plastic parts and components. Involvement and support this huge mass-production industry of laser cutting, new technology and dry-process using lasers were and are being actively developed. Fundamentally, industrial laser cutting or other applications on industry should satisfy the four key practical application issues including “Quality or Performance”, “Throughput or Speed”, “Cost or Total Ownership Cost”, and “Reliability”. Laser requires for examples several complicated physical factors to be resolved including die strength to be enable good wire-bonding and survival of severe cycling test, clean cutting wall surface, good cutting of direct attach film, and proper speed of cutting for achieving economy of throughput. Some example of maximum cutting rate, wherewith is normally limited laser energy, cutting speed is depend on type laser, different of cutting with one laser beam and beam pattern and applied laser power/material thickness will be introduced in this paper.

Feasibility Study of Cryogenic Cutting Technology by Using a Computer Simulation and Manufacture of Main Components for Cryogenic Cutting System

International Nuclear Information System (INIS)

Kim, Sung Kyun; Lee, Dong Gyu; Lee, Kune Woo; Song, Oh Seop

2009-01-01

Cryogenic cutting technology is one of the most suitable technologies for dismantling nuclear facilities due to the fact that a secondary waste is not generated during the cutting process. In this paper, the feasibility of cryogenic cutting technology was investigated by using a computer simulation. In the computer simulation, a hybrid method combined with the SPH (smoothed particle hydrodynamics) method and the FE (finite element) method was used. And also, a penetration depth equation, for the design of the cryogenic cutting system, was used and the design variables and operation conditions to cut a 10 mm thickness for steel were determined. Finally, the main components of the cryogenic cutting system were manufactures on the basis of the obtained design variables and operation conditions.

Comparison of blood loss between using non central part cutting knee prosthesis and distal central part cutting.

Science.gov (United States)

Malairungsakul, Anan

2014-12-01

Patients who undergo knee replacement surgery may need to receive a blood transfusion due to blood loss during the operation. Therefore it was important to improve the design of knee implant operative procedures in an attempt to reduce the rate of blood loss. The present study aimed to compare the blood loss between two types of knee replacement surgery. This is a retrospective study in which 78 patients received cemented knee replacements in Phayao Hospital between October 2010 and March 2012. There were two types of surgical procedure: 1) using an implant position covering the end of the femoral bone without cutting into the central part of the distal femoral, 2) using an implant position covering the end of the femoral bone cutting the central part of the distal femoral. Blood loss, blood transfusion, hemoglobin and hematocrit were recorded preoperatively, immediately postsurgery and 48 hours after surgery. Findings revealed that the knee replacement surgery using the implant position covering the end of the femoral bone without cutting the central part of the distal femoral significantly lowered the rate of blood loss when compared to using the implant position covering the end of the femoral bone with central cutting of the distal femor. The average blood loss during the operation without cutting at the central part of distal femoral was 49.50 ± 11.11 mL; whereas the operation cutting the central part of the distal femoral was 58.50 ± 11.69 mL. As regards blood loss, the knee replacement surgery using the implant position covering the end ofthefemoral bone without cutting the central part of distal femor was better than using the implant position covering the end of the femoral bone cutting at the central part of the distal femor.

Commissioning a hobby cutting device for radiochromic film preparation.

Science.gov (United States)

Zolfaghari, Somayeh; Francis, Kirby E; Kairn, Tanya; Crowe, Scott B

2017-06-01

In addition to a high spatial resolution and well characterised dose response, one of the major advantages of radiochromic film as a dosimeter is that sheets of film can be cut into pieces suitable for use as calibration films, and for in vivo and phantom measurements. The cutting of film is typically done using scissors or a guillotine, and this process can be time-consuming, limited in precision, requires extensive handling and does not allow holes to be cut from the film without cutting from an existing edge. This study investigated the use of a Brother ScanNCut hobby cutting system for EBT3 film preparation. The optimal operating parameters (blade size, pressure, speed) that resulted in precise cuts with minimal delamination at cut edges were identified using test cutting patterns. These parameters were then used to cut a large film insert for a stereotactic head phantom for comparison against an insert cut with scissors. While the hobby cutting system caused a wider region of delamination at the film edge (1.8 mm) compared to scissors (1 mm), the hobby cutting system was found to be able to produce reproducible cuts more efficiently and more accurately than scissors. The use of the hobby cutting system is recommended for complex phantom inserts (containing sharp corners or holes for alignment rods) or in situations where large numbers of film pieces need to be prepared.

Failure mechanisms of superhard materials when cutting superalloys

International Nuclear Information System (INIS)

Focke, A.E.; Westermann, F.E.; Ermi, A.; Yavelak, J.; Hoch, M.

1975-01-01

The present research studies the reasons for the failure of tungsten carbide tools while cutting superalloys. There is a continuous layer of the superalloy in the bottom of the crater which from time to time is torn away locally, taking tungsten carbide crystal with it. Under recommended cutting conditions a plateau (unworn cutting surface) separates the crater from the cutting edge of the tool when cutting AISI 4340. This plateau is totally absent in all cutting of Inconel 718, even in short, two-minute tests. The crater intersects the cutting edge--only a thin wedge of carbide is left which either breaks off or deforms and wears very rapidly. Temperature measurements carried out by use of an infrared detector aimed on the corner of the tungsten carbide indicate at recommended speeds a sharp rise of the temperature at the beginning of the cutting operation, then a steady-state very slow increase as the cutting continues, and finally just before tool failure a very rapid increase in the temperature again. Scanning and replica electron microscopy through the crater and flank face shows that both under the crater and in the back of the cutting edge a fairly deep layer of ''disturbed metal'' exists in which the tungsten carbide grains are much smaller and have much more rounded edges than in the original material. 10 figures, 4 tables

Regge cuts in inclusive reactions

International Nuclear Information System (INIS)

Paige, F.E.; Trueman, T.L.

1975-01-01

The contribution of Regge cuts to single-particle inclusive processes is analyzed using the techniques of Gribov. The dependence of these contributions on the polarization state of the target is emphasized. A general formula is obtained and certain contributions to it are calculated. It is not possible, however, to reduce this to a simple, powerful formula expressing the total cut contribution in terms of other measurable quantities, as can be done for the cut contribution to the total cross section. The reasons for this are discussed in detail. The single-particle intermediate states, analogous to the absorption model for elastic scattering, are explicitly calculated as an illustration

International feedback experience on the cutting of reactor internal components

International Nuclear Information System (INIS)

Boucau, J.

2014-01-01

Westinghouse capitalizes more than 30 years of experience in the cutting of internal components of reactor and their packaging in view of their storage. Westinghouse has developed and validated different methods for cutting: plasma torch cutting, high pressure abrasive water jet cutting, electric discharge cutting and mechanical cutting. A long feedback experience has enabled Westinghouse to list the pros and cons of each cutting technology. The plasma torch cutting is fast but rises dosimetry concerns linked to the control of the cuttings and the clarity of water. Abrasive water jet cutting requires the installation of costly safety devices and of an equipment for filtering water but this technology allows accurate cuttings in hard-to-reach zones. Mechanical cutting is the most favourable technology in terms of wastes generation and of the clarity of water but the cutting speed is low. (A.C.)

Shearer drums - the cutting edge

Energy Technology Data Exchange (ETDEWEB)

O' Neill, M.; Wright, C.

2004-09-15

The paper discusses continuous miner and shearer cutters. It claims cutting drum require the same level of engineering know-how and technical expertise as do the machines driving them, and that the cutting drum, whether on a longwall shearer or continuous miner, comprises, the steel, pedestals, bit holders and the bits.

29 CFR 1910.254 - Arc welding and cutting.

Science.gov (United States)

2010-07-01

... 29 Labor 5 2010-07-01 2010-07-01 false Arc welding and cutting. 1910.254 Section 1910.254 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Welding, Cutting and Brazing § 1910.254 Arc welding and cutting. (a... following limits shall not be exceeded: (i) Alternating-current machines (A) Manual arc welding and cutting...

7 CFR 58.413 - Cutting and packaging rooms.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Cutting and packaging rooms. 58.413 Section 58.413....413 Cutting and packaging rooms. When small packages of cheese are cut and wrapped, separate rooms shall be provided for the cleaning and preparation of the bulk cheese and for the cutting and wrapping...

Development of liner cutting method for stainless steel liner

International Nuclear Information System (INIS)

Takahata, Masato; Wignarajah, Sivakmaran; Kamata, Hirofumi

2005-01-01

The present work is an attempt to develop a laser cutting method for cutting and removing stainless steel liners from concrete walls and floors in cells and fuel storage pools of nuclear facilities. The effects of basic laser cutting parameters such as cutting speed, assist gas flow etc. were first studied applying a 1 kW Nd:YAG laser to mock up concrete specimens lined with 3 mm thick stainless steel sheets. These initial studies were followed by studies on the effect of unevenness of the liner surface and on methods of confining contamination during the cutting process. The results showed that laser cutting is superior to other conventional cutting methods from the point of view of safety from radioactivity and work efficiency when cutting contaminated stainless steel liners. In addition to the above results, this paper describes the design outline of a laser cutting system for cutting stainless liners at site and evaluates its merit and cost performance. (author)

7 CFR 58.726 - Cutting and grinding.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Cutting and grinding. 58.726 Section 58.726 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.726 Cutting and grinding. The trimmed and cleaned cheese should be cut into sections of...

A cutting force model for micromilling applications

DEFF Research Database (Denmark)

Bissacco, Giuliano; Hansen, Hans Nørgaard; De Chiffre, Leonardo

2006-01-01

In micro milling the maximum uncut chip thickness is often smaller than the cutting edge radius. This paper introduces a new cutting force model for ball nose micro milling that is capable of taking into account the effect of the edge radius.......In micro milling the maximum uncut chip thickness is often smaller than the cutting edge radius. This paper introduces a new cutting force model for ball nose micro milling that is capable of taking into account the effect of the edge radius....

Effects of Cutting Tool Parameters on Vibration

Directory of Open Access Journals (Sweden)

Ince Mehmet Alper

2016-01-01

Full Text Available This paper presents of the influence on vibration of Co28Cr6Mo medical alloy machined on a CNC lathe based on cutting parameters (rotational speed, feed rate, depth of cut and tool tip radius. The influences of cutting parameters have been presented in graphical form for understanding. To achieve the minimum vibration, the optimum values obtained for rpm, feed rate, depth of cut and tool tip radius were respectively, 318 rpm, 0.25 mm/rev, 0.9 mm and 0.8 mm. Maximum vibration has been revealed the values obtained for rpm, feed rate, depth of cut and tool tip radius were respectively, 636 rpm, 0.1 mm/rev, 0,5 mm and 0.8 mm.

HgI{sub 2} detector fabrication; Construccion de detectores de HgI{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, M.; Perez, J. M.

1996-07-01

The aim of the present work is to describe the steps followed to fabricate an ionizing radiation detector based on synthetic mercuric iodide monocrystal layers. Firstly, the crystalline orientation method has been describe, which is needed before the layer cutting perpendicularly to the (001) crystallographic. It is also defined the proceeding to crystal face finishing by a mechanical polishing and subsequent chemical etching. then, the metal electrode deposition and the view connection has been explained. Finally, the technique followed to encapsulate the detector with a polymeric thin film deposition has been described. (Author) 10 refs.

Diamond wire cutting of heat exchangers

International Nuclear Information System (INIS)

Beckman, T.R.; Bjerler, J.

1991-01-01

With the change-out of equipment at nuclear power plants comes large quantities of low level contaminated metallic waste. Of particular concern are large heat exchangers, preheaters and steam generators. These bulky items consume huge volumes of burial space. The need for volume reduction and recycling of these metals has created new demands for 'how' to cut heat exchangers into useful sizes for decontamination, melting or compaction. This paper reviews the cutting solution provided by a diamond wire system, with particular regard for cutting of a Ringhals Preheater Bundle at Studsvik Nuclear in 1989. The background of diamond wire sawing is discussed and basic components of wire sawing are explained. Other examples of wire cutting decommissioned components are also given. (author)

Assembly procedure for column cutting platform

International Nuclear Information System (INIS)

Routh, R.D.

1995-01-01

This supporting document describes the assembly procedure for the Column Cutting Platform and Elevation Support. The Column Cutting Platform is a component of the 241-SY-101 Equipment Removal System. It is set up on the deck of the Strongback Trailer to provide work access to cut off the upper portion of the Mitigation Pump Assembly (MPA). The Elevation Support provides support for the front of the Storage Container with the Strongback at an inclined position. The upper portion of the MPA must be cut off to install the Containment Caps on the Storage Container. The storage Container must be maintained in an inclined position until the Containment Caps are installed to prevent any residual liquids from migrating forward in the Storage Container

Rapid Fabrication of Electrophoretic Microfluidic Devices from Polyester, Adhesives and Gold Leaf

Directory of Open Access Journals (Sweden)

Christopher Birch

2017-01-01

Full Text Available In the last decade, the microfluidic community has witnessed an evolution in fabrication methodologies that deviate from using conventional glass and polymer-based materials. A leading example within this group is the print, cut and laminate (PCL approach, which entails the laser cutting of microfluidic architecture into ink toner-laden polyester sheets, followed by the lamination of these layers for device assembly. Recent success when applying this method to human genetic fingerprinting has highlighted that it is now ripe for the refinements necessary to render it amenable to mass-manufacture. In this communication, we detail those modifications by identifying and implementing a suitable heat-sensitive adhesive (HSA material to equip the devices with the durability and resilience required for commercialization and fieldwork. Importantly, this augmentation is achieved without sacrificing any of the characteristics which make the PCL approach attractive for prototyping. Exemplary HSA-devices performed DNA extraction, amplification and separation which, when combined, constitute the complete sequence necessary for human profiling and other DNA-based analyses.

Influence of Cutting Speed on Subsurface Damage Morphology and Distribution in Ground Fused Silica

Directory of Open Access Journals (Sweden)

Georg Schnurbusch

2017-08-01

Full Text Available In optical fabrication, brittle-hard materials are used for numerous applications. Especially for high-performance optics for laser or lithography applications, a complex and consistent production chain is necessary to account for the material properties. Particularly in pre-processing, e.g., for shaping optical components, brittle material behavior is dominant which leads to a rough surface layer with cracks that reach far below the surface. This so called subsurface damage (SSD needs to be removed in subsequent processes like polishing. Therefore, it is essential to know the extent of the SSD induced by shaping for an efficient design of precise corrective processes and for process improvement. Within this work the influence of cutting speed on SSD, in fused silica, induced by grinding has been investigated. To analyze the subsurface crack distribution and the maximum crack depth magnetorheological finishing has been appointed to polish a wedge into the ground surface. The depth profile of SSD was analyzed by image processing. For this purpose a coherent area of the polished wedge has been recorded by stitching microscopy. Taking the form deviation of the ground surface in to account to determine the actual depth beneath surface, the accuracy of the SSD-evaluation could be improved significantly. The experiments reveal a clear influence of the cutting speed on SSD, higher cutting speeds generate less SSD. Besides the influence on the maximum crack depth an influence on the crack length itself could be verified. Based on image analysis it was possible, to predict the maximum depth of cracks by means of crack length.

49 CFR 236.52 - Relayed cut-section.

Science.gov (United States)

2010-10-01

..., MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Rules and Instructions: All Systems Track Circuits § 236.52 Relayed cut-section. Where relayed cut-section is used in... 49 Transportation 4 2010-10-01 2010-10-01 false Relayed cut-section. 236.52 Section 236.52...

Polymorphous computing fabric

Science.gov (United States)

Wolinski, Christophe Czeslaw [Los Alamos, NM; Gokhale, Maya B [Los Alamos, NM; McCabe, Kevin Peter [Los Alamos, NM

2011-01-18

Fabric-based computing systems and methods are disclosed. A fabric-based computing system can include a polymorphous computing fabric that can be customized on a per application basis and a host processor in communication with said polymorphous computing fabric. The polymorphous computing fabric includes a cellular architecture that can be highly parameterized to enable a customized synthesis of fabric instances for a variety of enhanced application performances thereof. A global memory concept can also be included that provides the host processor random access to all variables and instructions associated with the polymorphous computing fabric.

Fabrication of First 4-m Coils for the LARP MQXFA Quadrupole and Assembly in Mirror Structure

CERN Document Server

Holik, E F; Anerella, M; Bossert, R; Cavanna, E; Cheng, D; Dietderich, D R; Ferracin, P; Ghosh, A K; Izquierdo Bermudez, S; Krave, S; Nobrega, A; Perez, J C; Pong, I; Sabbi, G L; Santini, C; Schmalzle, J; Wanderer, P; Wang, X; Yu, M

2017-01-01

The US LHC Accelerator Research Program is constructing prototype interaction region quadrupoles as part of the US in-kind contribution to the Hi-Lumi LHC project. The low-beta MQXFA Q1/Q3 coils have a 4-m length and a 150 mm bore. The design is first validated on short, one meter models (MQXFS) developed as part of the longstanding Nb$_{3}$Sn quadrupole R&D; by LARP in collaboration with CERN. In parallel, facilities and tooling are being developed and refined at BNL, LBNL, and FNAL to enable long coil production, assembly, and cold testing. Long length scale-up is based on the experience from the LARP 90 mm aperture (TQ-LQ) and 120 mm aperture (HQ and Long HQ) programs. A 4-m long MQXF practice coil was fabricated, water jet cut and analyzed to verify procedures, parts, and tooling. In parallel, the first complete prototype coil (QXFP01a) was fabricated and assembled in a long magnetic mirror, MQXFPM1, to provide early feedback on coil design and fabrication following the successful experience of previo...

LASER CUTTING MACHINES FOR 3-D THIN SHEET PARTS

Directory of Open Access Journals (Sweden)

Miroslav RADOVANOVIC

2012-11-01

Full Text Available Laser cutting machines are used for precise contour cutting thin sheet. In industrial application nowadays various types and construction of laser cutting machines can be met. For contour cutting 3-D thin sheet parts laser cutting machines with rotation movements and laser robots are used. Laser generates the light beam, that presents a tool in working process. Application of laser cutting machines made possible good quality of products, flexibility of production and enlargement of economy

Electric arc, water jet cutting of metals

International Nuclear Information System (INIS)

Bruening, D.

1991-01-01

For thermal dismantling and cutting of metallic components, as electric arc, water jet cutting method was developed that can be used for underwater cutting work up to a depth of 20 m. Short-circuiting of a continuously fed electrode wire in contact with the metal generates an electric arc which induces partial melting of the metal, and the water jet surrounding the wire rinses away the molten material, thus making a continuous kerf in the material. The method was also tested and modified to allow larger area, surface cutting and removal of metallic surface coatings. This is achieved by melting parts of the surface with the electric arc and subsequent rinsing by the water jet. The cutting and melting depth for surface removal can be accurately controlled by the operating parameters chosen. (orig./DG) [de

Modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for straight profile

Science.gov (United States)

Sharma, Amit; Yadava, Vinod

2012-02-01

Thin sheets of aluminium alloys are widely used in aerospace and automotive industries for specific applications. Nd:YAG laser beam cutting is one of the most promising sheetmetal cutting process for cutting sheets for any profile. Al-alloy sheets are difficult to cut by laser beam because of its highly reflective nature. This paper presents modelling and optimization of cut quality during pulsed Nd:YAG laser cutting of thin Al-alloy sheet for straight profile. In the present study, four input process parameters such as oxygen pressure, pulse width, pulse frequency, and cutting speed and two output parameters such as average kerf taper ( Ta) and average surface roughness ( Ra) are considered. The hybrid approach comprising of Taguchi methodology (TM) and response surface methodology (RSM) is used for modelling whereas multi-objective optimization is performed using hybrid approach of TM and grey relational analysis (GRA) coupled with entropy measurement methodology. The entropy measurement methodology is employed for the calculation of weight corresponding to each quality characteristic. The results indicate that the hybrid approaches applied for modelling and optimization of the LBC process are reasonable.

Neodymium:YAG laser cutting of intraocular lens haptics.

Science.gov (United States)

Gorn, R A; Steinert, R F

1985-11-01

Neodymium:YAG laser cutting of polymethylmethacrylate and polypropylene anterior chamber and posterior chamber intraocular lens haptics was studied in terms of ease of transection and physical structure of the cut areas as seen by scanning electron microscopy. A marked difference was discovered, with the polymethylmethacrylate cutting easily along transverse planes, whereas the polypropylene resisted cutting along longitudinal fibers. Clinical guidelines are presented.

Preliminary investigation on welding and cutting methods for first wall support leg in ITER blanket module

International Nuclear Information System (INIS)

Mohri, Kensuke; Suzuki, Satoshi; Enoeda, Mikio; Kakudate, Satoshi; Shibanuma, Kiyoshi; Akiba, Masato

2006-08-01

Concept of a module type of blanket has been applied to ITER shield blanket, of which size is typically 1mW x 1mH x 0.4mB with the weight of 4 ton, in order to enhance its maintainability and fabricability. Each shield blanket module consists of a shield block and four first walls which are separable from the shield block for the purpose of reduction of an electro-magnetic force in disruption events, radio-active waste reduction in the maintenance work and cost reduction in fabrication process. A first wall support leg, a part of the first wall component located between the first wall and the shield block, is required not only to be connected metallurgically to the shield block in order to withstand the electro-magnetic force and coolant pressure, but also to be able to replace the first wall more than 2 times in the hot cell during the life time of the reactor. Therefore, the consistent structure where remote handling equipment can be access to the joint and carry out the welding/cutting works perfectly to replace the first wall in the hot cell is required in the shield blanket design. This study shows an investigation of the blanket module no.10 design with a new type of the first wall support leg structure based on Disc-Cutter technology, which had been developed for the main pipe cutting in the maintenance phase and was selected out of a number of candidate methods, taking its large advantages into account, such as 1) a post-treatment can be eliminated in the hot cell because of no making material chips and of no need of lubricant, 2) the cut surface can be rewelded without any machining. And also, a design for the small type of Disc-Cutter applied to the new blanket module no.10 has been investigated. In conclusion, not only the good performance of Disc-Cutter technology applied to the updated blanket module, but also consistent structure of the simplified shield blanket module including the first wall support leg in order to satisfy the requirements in the

Detailed Design and Fabrication Method of the ITER Vacuum Vessel Ports

International Nuclear Information System (INIS)

Hee-Jae Ahn; Kwon, T.H.; Hong, Y.S.

2006-01-01

The engineering design of the ITER vacuum vessel (VV) has been progressed by the ITER International Team (IT) with the cooperation of several participant teams (PT). The VV and ports are the components allocated to Korea for the construction of the ITER. Hyundai Heavy Industries has been involved in the structural analysis, detailed design and development of the fabrication method of the upper and lower ports within the framework of the ITER transitional arrangements (ITA). The design of the port structures has been investigated to validate and to improve the conceptual designs of the ITER IT and other PT. The special emphasis was laid on the flange joint between the port extension and the in-port plug to develop the design of the upper port. The modified design with a pure friction type flange with forty-eight pieces of bolts instead of the tangential key is recommended. Furthermore, the alternative flange designs developed by the ITER IT have been analyzed in detail to simplify the lip seal maintenance into the port flange. The structural analyses of the lower RH port have been also performed to verify the capacity for supporting the VV. The maximum stress exceeds the allowable value at the reinforcing block and basement. More elaborate local models have been developed to mitigate the stress concentration and to modify the component design. The fabrication method and the sequence of the detailed fabrication for the ports are developed focusing on the cost reduction as well as the simplification. A typical port structure includes a port stub, a stub extension and a port extension with a connecting duct. The fabrication sequence consists of surface treatment, cutting, forming, cleaning, welding, machining, and non-destructive inspection and test. Tolerance study has been performed to avoid the mismatch of each fabricated component and to obtain the suitable tolerances in the assembly at the shop and site. This study is based on the experience in the fabrication of

Automated Cell-Cutting for Cell Cloning

Science.gov (United States)

Ichikawa, Akihiko; Tanikawa, Tamio; Matsukawa, Kazutsugu; Takahashi, Seiya; Ohba, Kohtaro

We develop an automated cell-cutting technique for cell cloning. Animal cells softened by the cytochalasin treatment are injected into a microfluidic chip. The microfluidic chip contains two orthogonal channels: one microchannel is wide, used to transport cells, and generates the cutting flow; the other is thin and used for aspiration, fixing, and stretching of the cell. The injected cell is aspirated and stretched in the thin microchannel. Simultaneously, the volumes of the cell before and after aspiration are calculated; the volumes are used to calculate the fluid flow required to aspirate half the volume of the cell into the thin microchannel. Finally, we apply a high-speed flow in the orthogonal microchannel to bisect the cell. This paper reports the cutting process, the cutting system, and the results of the experiment.

Benefits of explosive cutting for nuclear-facility applications

International Nuclear Information System (INIS)

Hazelton, R.F.; Lundgren, R.A.; Allen, R.P.

1981-06-01

The study discussed in this report was a cost/benefit analysis to determine: (1) whether explosive cutting is cost effective in comparison with alternative metal sectioning methods and (2) whether explosive cutting would reduce radiation exposure or provide other benefits. Two separate approaches were pursued. The first was to qualitatively assess cutting methods and factors involved in typical sectioning cases and then compare the results for the cutting methods. The second was to prepare estimates of work schedules and potential radiation exposures for candidate sectioning methods for two hypothetical, but typical, sectioning tasks. The analysis shows that explosive cutting would be cost effective and would also reduce radiation exposure when used for typical nuclear facility sectioning tasks. These results indicate that explosive cutting should be one of the principal cutting methods considered whenever steel or similar metal structures or equipment in a nuclear facility are to be sectioned for repair or decommissioning. 13 figures, 7 tables

Multilevel fluidic flow control in a rotationally-driven polyester film microdevice created using laser print, cut and laminate.

Science.gov (United States)

Ouyang, Yiwen; Li, Jingyi; Phaneuf, Christopher; Riehl, Paul S; Forest, Craig; Begley, Matthew; Haverstick, Doris M; Landers, James P

2016-01-21

This paper presents a simple and cost-effective polyester toner microchip fabricated with laser print and cut lithography (PCL) to use with a battery-powered centrifugal platform for fluid handling. The combination of the PCL microfluidic disc and centrifugal platform: (1) allows parallel aliquoting of two different reagents of four different volumes ranging from nL to μL with an accuracy comparable to a piston-driven air pipette; (2) incorporates a reciprocating mixing unit driven by a surface-tension pump for further dilution of reagents, and (3) is amenable to larger scale integration of assay multiplexing (including all valves and mixers) without substantially increasing fabrication cost and time. For a proof of principle, a 10 min colorimetric assay for the quantitation of the protein level in the human blood plasma samples is demonstrated on chip with a limit of detection of ∼5 mg mL(-1) and coefficient of variance of ∼7%.

Budget Cuts: Financial Aid Offices Face Budget Cuts and Increasing Workload. Quick Scan Survey Results

Science.gov (United States)

National Association of Student Financial Aid Administrators (NJ1), 2010

2010-01-01

The majority of college financial aid offices have seen cuts to their operating budgets this year compared to the 2007-08 academic year when the recession began, according to the National Association of Student Financial Aid Administrator's latest QuickScan Survey. Sixty-two percent of financial aid offices reported operating budget cuts this year…

Cut elimination in multifocused linear logic

DEFF Research Database (Denmark)

Guenot, Nicolas; Brock-Nannestad, Taus

2015-01-01

We study cut elimination for a multifocused variant of full linear logic in the sequent calculus. The multifocused normal form of proofs yields problems that do not appear in a standard focused system, related to the constraints in grouping rule instances in focusing phases. We show that cut...... elimination can be performed in a sensible way even though the proof requires some specific lemmas to deal with multifocusing phases, and discuss the difficulties arising with cut elimination when considering normal forms of proofs in linear logic....

MBS Ratings and the Mortgage Credit Boom

NARCIS (Netherlands)

Ashcraft, A.; Goldsmith-Pinkham, P.; Vickery, J.

2010-01-01

We study credit ratings on subprime and Alt-A mortgage-backed securities (MBS) deals issued between 2001 and 2007, the period leading up to the subprime crisis. The fraction of highly-rated securities in each deal is decreasing in mortgage credit risk (measured either ex-ante or ex-post), suggesting

Application of response surface methodology for determining cutting ...

Indian Academy of Sciences (India)

The results indicate that the depth of cut is the dominant factor affecting cutting ... between forces and cutting regime could be represented by power function type ..... CNEPRU Research Project, CODE : 0301520090008 (University of Guelma).

Thermophysical problems of laser cutting of metals

Directory of Open Access Journals (Sweden)

Orishich Anatoliy

2017-01-01

Full Text Available Variety and complex interaction of physical processes during laser cutting is a critical characteristic of the laser cutting of metals. Small spatial and temporal scales complicate significantly the experimental investigations of the multi-phase fluid flow in the conditions of laser cutting of metals. In these conditions, the surface formed during the cutting is an indicator determining the melt flow character. The quantitative parameter reflecting the peculiarities of the multi-phase fluid flow, is normally the roughness of the forming surface, and the minimal roughness is the criterion of the qualitative flow [1 – 2]. The purpose of this work is to perform the experimental comparative investigation of the thermophysical pattern of the multi-phase melt flow in the conditions of the laser cutting of metals with the laser wavelength of 10.6 μm and 1.07 μm.

Fractal characteristic study of shearer cutter cutting resistance curves

Energy Technology Data Exchange (ETDEWEB)

Liu, C. [Heilongjiang Scientific and Technical Institute, Haerbin (China). Dept of Mechanical Engineering

2004-02-01

The cutting resistance curve is the most useful tool for reflecting the overall cutting performance of a cutting machine. The cutting resistance curve is influenced by many factors such as the pick structure and arrangement, the cutter operation parameters, coal quality and geologic conditions. This paper discusses the use of fractal geometry to study the properties of the cutting resistance curve, and the use of fractal dimensions to evaluate cutting performance. On the basis of fractal theory, the general form and calculation method of fractal characteristics are given. 4 refs., 3 figs., 1 tab.

Effect of cutting temperature on hardness of SiC and diamond in the nano-cutting process of monocrystalline silicon

Science.gov (United States)

Wang, Jiachun; Li, Yuntao; Liu, Xiaoxuan; Lv, Maoqiang

2016-10-01

In the process of cutting silicon by natural diamond tools, groove wear happens on the flank face of cutting tool frequently.Scholars believe that one of the wear reasons is mechanical scratching effect by hard particles like SiC. To reveal the mechanical scratching mechanism, it is essential to study changes in the mechanical properties of hard particles and diamond, especially the effect of cutting temperature on hardness of diamond and hard particles. Molecular dynamics (MD) model that contact-zone temperature between tool and workpiece was calculated by dividing zone while nano-cutting monocrystalline silicon was established, cutting temperature values in different regions were computed as the simulation was carried out.On this basis, the models of molecular dynamics simulation of SiC and diamond were established separately with setting the initial temperature to room temperature. The laws of length change of C-C bond and Si-C bond varing with increase of simulation temperature were studied. And drawing on predecessors' research on theoretical calculation of hardness of covalent crystals and the relationship between crystal valence electron density and bond length, the curves that the hardness of diamond and SiC varing with bond length were obtained. The effect of temperature on the hardness was calculated. Results show that, local cutting temperature can reach 1300K.The rise in cutting temperature leaded to a decrease in the diamond local atomic clusters hardness,SiC local atomic clusters hardness increased. As the cutting temperature was more than 1100K,diamond began to soften, the local clusters hardness was less than that of SiC.

Recent results in mirror based high power laser cutting

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Nielsen, Jakob Skov; Elvang, Mads

2004-01-01

In this paper, recent results in high power laser cutting, obtained in reseach and development projects are presented. Two types of mirror based focussing systems for laser cutting have been developed and applied in laser cutting studies on CO2-lasers up to 12 kW. In shipyard environment cutting...... speed increase relative to state-of-the-art cutting of over 100 % has been achieved....

Magnetofluidic testing of rock cutting knives

International Nuclear Information System (INIS)

Buioca, C.D.; Iusan, Vasile; Pirlea, Remus

2002-01-01

The nondestructive testing of cutting knives consists in the determination of nonuniformity of a magnetic fluid layer applied on the horizontally placed surface of the magnetized cutting plate of the knife. A low constant magnetic field was applied perpendicular to the knife surface and a uniform magnetic fluid layer was applied. The defects as nonuniform brass layer, fissures or small cavities between the cutting plate and knife core determine the apparition of magnetic field gradients and therefore magnetic forces acting on the magnetic fluid which migrates to the zones with higher magnetic field intensity. After several minutes, a nonuniform layer of magnetic fluid was directly observed. Quantitative results, concerning the position and dimensions of the defect, were obtained by computer aided processing of the magnetic fluid layer image. Experimental data for several cutting knives are presented in the paper

Fabrication of Thermoelectric Devices Using Additive-Subtractive Manufacturing Techniques: Application to Waste-Heat Energy Harvesting

Science.gov (United States)

Tewolde, Mahder

Thermoelectric generators (TEGs) are solid-state devices that convert heat directly into electricity. They are well suited for waste-heat energy harvesting applications as opposed to primary energy generation. Commercially available thermoelectric modules are flat, inflexible and have limited sizes available. State-of-art manufacturing of TEG devices relies on assembling prefabricated parts with soldering, epoxy bonding, and mechanical clamping. Furthermore, efforts to incorporate them onto curved surfaces such as exhaust pipes, pump housings, steam lines, mixing containers, reaction chambers, etc. require custom-built heat exchangers. This is costly and labor-intensive, in addition to presenting challenges in terms of space, thermal coupling, added weight and long-term reliability. Additive manufacturing technologies are beginning to address many of these issues by reducing part count in complex designs and the elimination of sub-assembly requirements. This work investigates the feasibility of utilizing such novel manufacturing routes for improving the manufacturing process of thermoelectric devices. Much of the research in thermoelectricity is primarily focused on improving thermoelectric material properties by developing of novel materials or finding ways to improve existing ones. Secondary to material development is improving the manufacturing process of TEGs to provide significant cost benefits. To improve the device fabrication process, this work explores additive manufacturing technologies to provide an integrated and scalable approach for TE device manufacturing directly onto engineering component surfaces. Additive manufacturing techniques like thermal spray and ink-dispenser printing are developed with the aim of improving the manufacturing process of TEGs. Subtractive manufacturing techniques like laser micromachining are also studied in detail. This includes the laser processing parameters for cutting the thermal spray materials efficiently by

Laser cutting - from 200 Watt to 12 Kilowatt

DEFF Research Database (Denmark)

Olsen, Flemming Ove; Nielsen, Jakob Skov

2004-01-01

Laser cutting is the most widespread industrial application of high power lasers. The development of this process was initiated around 1970, when scientists at TWI first demonstrated laser cutting with coaxial gas assistance. 10 years later, the polarisation problem was solved and the technology ...... got its breakthrough. Since then some 30,000 laser cutting systems have been installed worldwide, making the laser an important cutting tool in modern industry....

Investigation of tool engagement and cutting performance in machining a pocket

Science.gov (United States)

Adesta, E. Y. T.; Hamidon, R.; Riza, M.; Alrashidi, R. F. F. A.; Alazemi, A. F. F. S.

2018-01-01

This study investigates the variation of tool engagement for different profile of cutting. In addition, behavior of cutting force and cutting temperature for different tool engagements for machining a pocket also been explored. Initially, simple tool engagement models were developed for peripheral and slot cutting for different types of corner. Based on these models, the tool engagements for contour and zig zag tool path strategies for a rectangular shape pocket with dimension 80 mm x 60 mm were analyzed. Experiments were conducted to investigate the effect of tool engagements on cutting force and cutting temperature for the machining of a pocket of AISI H13 material. The cutting parameters used were 150m/min cutting speed, 0.05mm/tooth feed, and 0.1mm depth of cut. Based on the results obtained, the changes of cutting force and cutting temperature performance there exist a relationship between cutting force, cutting temperature and tool engagement. A higher cutting force and cutting temperature is obtained when the cutting tool goes through up milling and when the cutting tool makes a full engagement with the workpiece.

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718

Directory of Open Access Journals (Sweden)

Bing Wang

2018-03-01

Full Text Available The paper aims to investigate the influences of material constitutive and fracture parameters in addition to cutting speed on chip formation during high-speed cutting of Inconel 718. Finite element analyses for chip formation are conducted with Johnson–Cook constitutive and fracture models. Meanwhile, experiments of high-speed orthogonal cutting are performed to verify the simulation results with cutting speeds ranging from 50 m/min to 7000 m/min. The research indicates that the chip morphology transforms from serrated to fragmented at the cutting speed of 7000 m/min due to embrittlement of the workpiece material under ultra-high cutting speeds. The parameter of shear localization sensitivity is put forward to describe the influences of material mechanical properties on serrated chip formation. The results demonstrate that the effects of initial yield stress and thermal softening coefficient on chip shear localization are much more remarkable than the other constitutive parameters. For the material fracture parameters, the effects of initial fracture strain and exponential factor of stress state on chip shear localization are more much prominent. This paper provides guidance for controlling chip formation through the adjustment of material mechanical properties and the selection of appropriate cutting parameters.

Influences of Cutting Speed and Material Mechanical Properties on Chip Deformation and Fracture during High-Speed Cutting of Inconel 718.

Science.gov (United States)

Wang, Bing; Liu, Zhanqiang; Hou, Xin; Zhao, Jinfu

2018-03-21

The paper aims to investigate the influences of material constitutive and fracture parameters in addition to cutting speed on chip formation during high-speed cutting of Inconel 718. Finite element analyses for chip formation are conducted with Johnson-Cook constitutive and fracture models. Meanwhile, experiments of high-speed orthogonal cutting are performed to verify the simulation results with cutting speeds ranging from 50 m/min to 7000 m/min. The research indicates that the chip morphology transforms from serrated to fragmented at the cutting speed of 7000 m/min due to embrittlement of the workpiece material under ultra-high cutting speeds. The parameter of shear localization sensitivity is put forward to describe the influences of material mechanical properties on serrated chip formation. The results demonstrate that the effects of initial yield stress and thermal softening coefficient on chip shear localization are much more remarkable than the other constitutive parameters. For the material fracture parameters, the effects of initial fracture strain and exponential factor of stress state on chip shear localization are more much prominent. This paper provides guidance for controlling chip formation through the adjustment of material mechanical properties and the selection of appropriate cutting parameters.

Underwater transporting method and device for incore structure cutting piece

International Nuclear Information System (INIS)

Kurosawa, Koichi; Chiba, Noboru; Chiba, Isao; Takada, Hiroshi; Furukawa, Hideyasu; Chiba, Noboru.

1996-01-01

Cutting pieces are handled by using a pick-up device connected with a wire ropes, a take-up drum, chains and a winch as cutting piece handling means, and moved freely on the water surface by a propulsion machine of a transporting means of the device to transfer them under water to a predetermined position. The pick-up device is lifted by taking-up the rope by the rotation of the take-up drum using chain-driving by way of the winch and the chains. The cut pieces are stored in a cask by lowering them in the cask and releasing the handling. In addition, if the weight of the cut pieces is recognized before cutting, and the load of the weight of the cut pieces is applied to the device previously, the balance of the device and the cut pieces can be kept, and cut pieces can be transported under water always stably. Further, if the cut pieces are supported upon cutting operation, the cut pieces are made stable, and cutting operation with good efficiency can be attained. (N.H.)

Counterbalance of cutting force for advanced milling operations

Science.gov (United States)

Tsai, Nan-Chyuan; Shih, Li-Wen; Lee, Rong-Mao

2010-05-01

The goal of this work is to concurrently counterbalance the dynamic cutting force and regulate the spindle position deviation under various milling conditions by integrating active magnetic bearing (AMB) technique, fuzzy logic algorithm and an adaptive self-tuning feedback loop. Since the dynamics of milling system is highly determined by a few operation conditions, such as speed of spindle, cut depth and feedrate, therefore the dynamic model for cutting process is more appropriate to be constructed by experiments, instead of using theoretical approach. The experimental data, either for idle or cutting, are utilized to establish the database of milling dynamics so that the system parameters can be on-line estimated by employing the proposed fuzzy logic algorithm as the cutting mission is engaged. Based on the estimated milling system model and preset operation conditions, i.e., spindle speed, cut depth and feedrate, the current cutting force can be numerically estimated. Once the current cutting force can be real-time estimated, the corresponding compensation force can be exerted by the equipped AMB to counterbalance the cutting force, in addition to the spindle position regulation by feedback of spindle position. On the other hand, for the magnetic force is nonlinear with respect to the applied electric current and air gap, the characteristics of the employed AMB is investigated also by experiments and a nonlinear mathematic model, in terms of air gap between spindle and electromagnetic pole and coil current, is developed. At the end, the experimental simulations on realistic milling are presented to verify the efficacy of the fuzzy controller for spindle position regulation and the capability of the dynamic cutting force counterbalance.

Metal Cutting for Large Component Removal

International Nuclear Information System (INIS)

Hulick, Robert M.

2008-01-01

Decommissioning of commercial nuclear power plants presents technological challenges. One major challenge is the removal of large components mainly consisting of the reactor vessel, steam generators and pressurizer. In order to remove and package these large components nozzles must be cut from the reactor vessel to precise tolerances. In some cases steam generators must be segmented for size and weight reduction. One innovative technology that has been used successfully at several commercial nuclear plant decommissioning is diamond wire sawing. Diamond wire sawing is performed by rotating a cable with diamond segments attached using a flywheel approximately 24 inches in diameter driven remotely by a hydraulic pump. Tension is provided using a gear rack drive which also takes up the slack in the wire. The wire is guided through the use of pulleys keeps the wire in a precise location. The diamond wire consists of 1/4 inch aircraft cable with diamond beads strung over the cable separated by springs and brass crimps. Standard wire contains 40 diamond beads per meter and can be made to any length. Cooling the wire and controlling the spread of contamination presents significant challenges. Under normal circumstances the wire is cooled and the cutting kerf cleaned by using water. In some cases of reactor nozzle cuts the use of water is prohibited because it cannot be controlled. This challenge was solved by using liquid Carbon Dioxide as the cooling agent. The liquid CO 2 is passed through a special nozzle which atomizes the liquid into snowflakes which is introduced under pressure to the wire. The snowflakes attach to the wire keeping it cool and to the metal shavings. As the CO 2 and metal shavings are released from the wire due to its fast rotation, the snowflakes evaporate leaving only the fine metal shavings as waste. Secondary waste produced is simply the small volume of fine metal shavings removed from the cut surface. Diamond wire sawing using CO 2 cooling has

Cutting of nonmetallic materials using Nd:YAG laser beam

Institute of Scientific and Technical Information of China (English)

Bashir Ahmed Tahir; Rashid Ahmed; M. G. B. Ashiq; Afaq Ahmed; M. A. Saeed

2012-01-01

This study deals with Nd:YAG laser cutting nonmetallic materials,which is one of the most important and popular industrial applications of laser.The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed.For approximate cutting depth,a theoretical study is conducted in terms of material property and cutting speed.Results show a nonlinear relation between the cutting depth and input energy.There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s.An extra energy is utilized in the deep cutting.It is inferred that as the laser power increases,cutting depth increases.The experimental outcomes are in good agreement with theoretical results.This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting,scribing,trimming,engraving,and marking nonmetallic materials.

Effect of cutting fluids and cutting conditions on surface integrity and tool wear in turning of Inconel 713C

Science.gov (United States)

Hikiji, R.

2018-01-01

The trend toward downsizing of engines helps to increase the number of turbochargers around Europe. As for the turbocharger, the temperature of the exhaust gas is so high that the parts made of nickel base super alloy Inconel 713C are used as high temperature strength metals. External turning of Inconel 713C which is used as the actual automotive parts was carried out. The effect of the cutting fluids and cutting conditions on the surface integrity and tool wear was investigated, considering global environment and cost performance. As a result, in the range of the cutting conditions used this time, when the depth of cut was small, the good surface integrity and tool life were obtained. However, in the case of the large corner radius, it was found that the more the cutting length increased, the more the tool wear increased. When the cutting length is so large, the surface integrity and tool life got worse. As for the cutting fluids, it was found that the synthetic type showed better performance in the surface integrity and tool life than the conventional emulsion. However, it was clear that the large corner radius made the surface roughness and tool life good, but it affected the size error etc. in machining the workpiece held in a cantilever style.

77 FR 16587 - Proposed Collection; Comment Request for Notice

Science.gov (United States)

2012-03-21

... subprime mortgage loans. In addition, Sec. 3005 of the 2008 Housing Act amends Sec. 142(d)(2) of the Code... qualified housing issues and to allow the use of qualified mortgage bonds to refinance certain subprime mortgage loans. (Except as otherwise provided, section references in this notice are to the Code.) This...

MULTI-OBJECTIVE OPTIMISATION OF LASER CUTTING USING CUCKOO SEARCH ALGORITHM

Directory of Open Access Journals (Sweden)

M. MADIĆ

2015-03-01

Full Text Available Determining of optimal laser cutting conditions for improving cut quality characteristics is of great importance in process planning. This paper presents multi-objective optimisation of the CO2 laser cutting process considering three cut quality characteristics such as surface roughness, heat affected zone (HAZ and kerf width. It combines an experimental design by using Taguchi’s method, modelling the relationships between the laser cutting factors (laser power, cutting speed, assist gas pressure and focus position and cut quality characteristics by artificial neural networks (ANNs, formulation of the multiobjective optimisation problem using weighting sum method, and solving it by the novel meta-heuristic cuckoo search algorithm (CSA. The objective is to obtain optimal cutting conditions dependent on the importance order of the cut quality characteristics for each of four different case studies presented in this paper. The case studies considered in this study are: minimisation of cut quality characteristics with equal priority, minimisation of cut quality characteristics with priority given to surface roughness, minimisation of cut quality characteristics with priority given to HAZ, and minimisation of cut quality characteristics with priority given to kerf width. The results indicate that the applied CSA for solving the multi-objective optimisation problem is effective, and that the proposed approach can be used for selecting the optimal laser cutting factors for specific production requirements.

ANALYSIS OF CUTTING FORCES ON CNC LATHES EXPERIMENTAL APPROACH

Directory of Open Access Journals (Sweden)

Erdem Koç

1996-01-01

Full Text Available Objective of this study is to make use easy programming of CNC lathes and to achieve the optimization of part program prepared considering the limiting parameters of the machine. In the present study, a BOXFORD 250 B CNC lathe has been used for experiment and optimization process. The measurement of cutting forces exerted on the cutting tool of CNC lathe has been performed. The cutting forces occurring during the turning operation have been determined for different depth of" cut, feed rate and cutting speed as well as different cutting tools and related data base has been obtained.

Ceramic cutting tools materials, development and performance

CERN Document Server

Whitney, E Dow

1994-01-01

Interest in ceramics as a high speed cutting tool material is based primarily on favorable material properties. As a class of materials, ceramics possess high melting points, excellent hardness and good wear resistance. Unlike most metals, hardness levels in ceramics generally remain high at elevated temperatures which means that cutting tip integrity is relatively unaffected at high cutting speeds. Ceramics are also chemically inert against most workmetals.

Precision Machining When Cutting with Leading Plastic Deformation

Directory of Open Access Journals (Sweden)

N. A. Yaroslavtseva

2017-01-01

Full Text Available Keeping up the product competitiveness continually requires solving the problems of reducing time for product creation and material costs for its production and ensuring the maximum conformity of the product quality with the individual requirements of a particular consumer. It is especially difficult to implement these tasks in product manufacturing from the hard-to-machine steels and alloys with extremely low production rate in machining (often 10-20 times lower than when cutting the ordinary structural steels.Currently, one of the promising ways to improve the cutting process of hard-to-machine materials and quality of parts made from these materials is development and application of combined processing methods, which use additional energy sources to act on the machined material in the cutting zone. A BMSTU-developed cutting method with leading plastic deformation (LPD, which acts to raise the production rate, gain the cutting tool-life, reduce the surface roughness, improve the accuracy of processing and the performance characteristics of products, ensure the reliable flow chip control, and improve the labor conditions, belongs to such sort of methods.One of the most important indicators of processing quality that has a great impact on the operation and cost characteristics of the product and on the machining rate as well is the accuracy of processing. In cutting, the processing errors largely arise from the elastic deformations of a technological system when the cutting force, and, in particular, the radial component of the cutting force, acts on it.The deforming devices, used in cutting with LPD, being located as a rule, on the diametrically opposite side with respect to the cutting zone, act on the technological system as vibration dampers. In addition, as studies have shown, the choice of a rational direction for applying LPD load helps to compensate partially or completely the cutting force radial component effect on the technological

Long-term effects of clear-cutting and selective cutting on soil methane fluxes in a temperate spruce forest in southern Germany

International Nuclear Information System (INIS)

Wu Xing; Brueggemann, Nicolas; Gasche, Rainer; Papen, Hans; Willibald, Georg; Butterbach-Bahl, Klaus

2011-01-01

Based on multi-year measurements of CH 4 exchange in sub-daily resolution we show that clear-cutting of a forest in Southern Germany increased soil temperature and moisture and decreased CH 4 uptake. CH 4 uptake in the first year after clear-cutting (-4.5 ± 0.2 μg C m -2 h -1 ) was three times lower than during the pre-harvest period (-14.2 ± 1.3 μg C m -2 h -1 ). In contrast, selective cutting did not significantly reduce CH 4 uptake. Annual mean uptake rates were -1.18 kg C ha -1 yr -1 (spruce control), -1.16 kg C ha -1 yr -1 (selective cut site) and -0.44 kg C ha -1 yr -1 (clear-cut site), respectively. Substantial seasonal and inter-annual variations in CH 4 fluxes were observed as a result of significant variability of weather conditions, demonstrating the need for long-term measurements. Our findings imply that a stepwise selective cutting instead of clear-cutting may contribute to mitigating global warming by maintaining a high CH 4 uptake capacity of the soil. - Highlights: → Long-term, sub-daily measurements of CH 4 exchange at differently managed forest sites. → Inter-annual variability in CH 4 uptake is affected by annual precipitation. → Clear-cutting reduces the CH 4 sink strength of forest soils, whereas thinning has no significant effect. → Sink strength changes due to clear cutting are long-term and were still present approx. nine years following forest harvest. - Forest management affects the soil CH 4 sink strength, with clear-cutting reducing uptake rates for at least eight years.

Non-Poissonian photon statistics from macroscopic photon cutting materials.

Science.gov (United States)

de Jong, Mathijs; Meijerink, Andries; Rabouw, Freddy T

2017-05-24

In optical materials energy is usually extracted only from the lowest excited state, resulting in fundamental energy-efficiency limits such as the Shockley-Queisser limit for single-junction solar cells. Photon-cutting materials provide a way around such limits by absorbing high-energy photons and 'cutting' them into multiple low-energy excitations that can subsequently be extracted. The occurrence of photon cutting or quantum cutting has been demonstrated in a variety of materials, including semiconductor quantum dots, lanthanides and organic dyes. Here we show that photon cutting results in bunched photon emission on the timescale of the excited-state lifetime, even when observing a macroscopic number of optical centres. Our theoretical derivation matches well with experimental data on NaLaF 4 :Pr 3+ , a material that can cut deep-ultraviolet photons into two visible photons. This signature of photon cutting can be used to identify and characterize new photon-cutting materials unambiguously.

Cutting of nonmetallic materials using Nd:YAG laser beam

International Nuclear Information System (INIS)

Tahir, Bashir Ahmed; Ashiq, M.G. B.; Saeed, M.A.; Ahmed, Rashid; Ahmed, Afaq

2012-01-01

This study deals with Nd:YAG laser cutting nonmetallic materials, which is one of the most important and popular industrial applications of laser. The main theme is to evaluate the effects of Nd:YAG laser beam power besides work piece scanning speed. For approximate cutting depth, a theoretical study is conducted in terms of material property and cutting speed. Results show a nonlinear relation between the cutting depth and input energy. There is no significant effect of speed on cutting depth with the speed being larger than 30 mm/s. An extra energy is utilized in the deep cutting. It is inferred that as the laser power increases, cutting depth increases. The experimental outcomes are in good agreement with theoretical results. This analysis will provide a guideline for laser-based industry to select a suitable laser for cutting, scribing, trimming, engraving, and marking nonmetallic materials. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)

Remotely controlled cutting techniques in the field of nuclear decommissioning. Overview of effectively applied thermal and non thermal cutting methods

International Nuclear Information System (INIS)

Bienia, H.

2008-01-01

Remote disassembly of radiologically burdened large components is among the most sophisticated and complex activities in the dismantling of nuclear installations. The required space for the technical equipment during the dismantling operations, especially for the removal of larger components is often an additional problem. Conventional cutting technologies like sawing with a disk saw or band saw require large and heavy frameworks as well as guiding systems with high rigidity. These solutions are expensive and sometimes not applicable. The essential question of all cutting and dismantling tasks is the physiological constitution of the component which will be dismantled. That means size, material and structure of the component. All these points are primarily technological questions. The last question is about the estimated costs of the used dismantling technology. Therefore following questions must be answered. How much are the investments for the cutting equipment itself and how much are the investments for the supporting equipment (e.g. necessary handling equipment)? Can I use this cutting equipment only for one special task or is it applicable for many tasks and therefore saves money because other cutting or dismantling technologies are dispensable? How long is the cutting time and what is the to control this technique required personnel? Four different cutting and dismantling technologies will be introduced and described. These four technologies differ in their principle of operation but all of them are used by cutting and dismantling tasks in nuclear power plants. (author)