WorldWideScience

Sample records for submicron particles generated

  1. On the dry deposition of submicron particles

    Energy Technology Data Exchange (ETDEWEB)

    Wesely, M. L.

    1999-10-08

    The air-surface exchange of particles can have a strong role in determining the amount, size, and chemical composition of particles in the troposphere. Here the authors consider only dry processes (deposition processes not directly aided by precipitation) and mostly address particles less than about 2 {micro}m in diameter (often referred to as submicron particles because most of such particles are less than 1 {micro}m in diameter). The processes that control the dry exchange of particulate material between the atmosphere and the surface of the Earth are numerous, highly varied, and sometimes poorly understood. As a result, determining which of the surface processes to parameterize or simulate in modeling the tropospheric mass budget of a particulate substance can be a significant challenge. Dry deposition, for example, can be controlled by a combination of Brownian diffusion, impaction, interception, and gravitational settling, depending on the size of the particles, the roughness of the surface on both micrometeorological and microscopic scales, the geometrical structure of vegetative canopies, and other surface characteristics such as wetness. Particles can be added to the lower atmosphere by resuspension from land surfaces and sea spray. The roles of rapid gas-to-particle conversion and growth or shrinkage of particles as a result of water condensation or evaporation in the lower few meters of the atmosphere can also have a significant impact on particle concentrations in the lower atmosphere. Here, a few micrometeorological observations and inferences on particle air-surface exchange are briefly addressed.

  2. Surfactants and submicron sea spray generation

    NARCIS (Netherlands)

    Sellegri, K.; O'Dowd, C.D.; Yoon, Y.J.; Jennings, S.G.; Leeuw, G. de

    2006-01-01

    Laboratory experiments have been carried out to elucidate the role of surfactants on the primary marine aerosol production of submicron marine aerosols. A synthetic surfactant SDS was used in conjunction with artificially generated seawater, and the resultant bubble-mediated aerosol produced was

  3. Second-hand smoke exposure generated by new electronic devices (IQOS® and e-cigs) and traditional cigarettes: submicron particle behaviour in human respiratory system.

    Science.gov (United States)

    Protano, C; Manigrasso, M; Avino, P; Sernia, S; Vitali, M

    2016-01-01

    Passive exposure profiles to submicronic particles (SMPs, 5.6-560 nm) of traditional cigarettes and new electronic commercial devices (e-cig and IQOS®, a new heat-not-burn smoking device) were compared. During smoking, SMPs released by traditional cigarettes resulted four-times higher than those released by electronic and heat-not-burn devices and remained high for at least one hour, while SMPs values returned immediately similar to background for electronic and heat-not-burn devices. In all experiments, approximately half of SMPs resulted so small to reach the alveolar region.

  4. UV Light–Induced Aggregation of Titania Submicron Particles

    Directory of Open Access Journals (Sweden)

    Can Zhou

    2016-11-01

    Full Text Available In this study, aggregation of TiO2 (rutile and anatase submicron particles in deionized (DI water under ultra-violet (UV light irradiation was investigated. While no aggregation was observed in the dark, rutile and anatase submicron particles started aggregating upon application of UV light and ceased aggregation in about 2 and 8.4 h, respectively. It has been demonstrated that UV light directly mitigated the particle mobility of TiO2, resulting in a neutralization effect of the Zeta potential. It was also observed that rutile particles aggregated much faster than anatase particles under UV radiation, indicating that the Zeta potential of as-prepared rutile is less than that of anatase in deionized (DI water. In addition, the interaction energy of rutile and anatase particles was simulated using the Derjaguin–Landau–Verwey–Overbeek (DLVO model. The results showed a significant reduction of barrier energy from 118.2 kBT to 33.6 kBT for rutile and from 333.5 kBT to 46.1 kBT for anatase, respectively, which further validated the remarkable influence of UV irradiation on the aggregation kinetics of rutile and anatase submicron particles. This work presents a further understanding of the aggregation mechanism of light-controlled submicron particles and has a promising potential application in environmental remediation.

  5. Submicron particle chemistry: Vapor condensation analogous to liquid solidification

    Science.gov (United States)

    Jenkins, Neil T.; Eagar, Thomas W.

    2003-06-01

    The chemical composition of submicron particles condensed from vapor can vary with particle size. This chemical variation with size affects industrial health estimates and technological innovation. A model based on similar behavior during the solidification of liquids is proposed to explain this behavior.

  6. Submicron particles of Co, Ni and Co–Ni alloys

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 24; Issue 5 ... Magnetic Materials Volume 24 Issue 5 October 2001 pp 515-521 ... Magnetic sub-micron sized particles (with diameters in the range 100–600 nm) of Co, Ni and Co–Ni alloys, protected with polyvinylpyrrolidone have been prepared in gram quantities ...

  7. Submicron particle monitoring of paving and related road construction operations.

    Science.gov (United States)

    Freund, Alice; Zuckerman, Norman; Baum, Lisa; Milek, Debra

    2012-01-01

    This study identified activities and sources that contribute to ultrafine and other submicron particle exposure that could trigger respiratory symptoms in highway repair workers. Submicron particle monitoring was conducted for paving, milling, and pothole repair operations in a major metropolitan area where several highway repair workers were identified as symptomatic for respiratory illness following exposures at the 2001 World Trade Center disaster site. Exposure assessments were conducted for eight trades involved in road construction using a TSI P-Trak portable condensation particle counter. Direct readings near the workers' breathing zones and observations of activities and potential sources were logged on 7 days on 27 workers using four different models of pavers and two types of millers. Average worker exposure levels ranged from 2 to 3 times background during paving and from 1 to 4 times background during milling. During asphalt paving, average personal exposures to submicron particulates were 25,000-60,000, 28,000-70,000, and 23,000-37,000 particles/ cm(3) for paver operators, screed operators, and rakers, respectively. Average personal exposures during milling were 19,000-111,000, 28,000-81,000, and 19,000 particles/cm(3) for the large miller operators, miller screed operators, and raker, respectively. Personal peak exposures were measured up to 467,000 and 455,000 particles/cm(3) in paving and milling, respectively. Several sources of submicron particles were identified. These included the diesel and electric fired screed heaters; engine exhaust from diesel powered construction vehicles passing by or idling; raking, dumping, and paving of asphalt; exhaust from the hotbox heater; pavement dust or fumes from milling operations, especially when the large miller started and stopped; and secondhand cigarette smoke. To reduce the potential for health effects in workers, over 40 recommendations were made to control exposures, including improved maintenance of

  8. Online submicron particle sizing by dynamic light scattering using autodilution

    Science.gov (United States)

    Nicoli, David F.; Elings, V. B.

    1989-01-01

    Efficient production of a wide range of commercial products based on submicron colloidal dispersions would benefit from instrumentation for online particle sizing, permitting real time monitoring and control of the particle size distribution. Recent advances in the technology of dynamic light scattering (DLS), especially improvements in algorithms for inversion of the intensity autocorrelation function, have made it ideally suited to the measurement of simple particle size distributions in the difficult submicron region. Crucial to the success of an online DSL based instrument is a simple mechanism for automatically sampling and diluting the starting concentrated sample suspension, yielding a final concentration which is optimal for the light scattering measurement. A proprietary method and apparatus was developed for performing this function, designed to be used with a DLS based particle sizing instrument. A PC/AT computer is used as a smart controller for the valves in the sampler diluter, as well as an input-output communicator, video display and data storage device. Quantitative results are presented for a latex suspension and an oil-in-water emulsion.

  9. Short range investigation of sub-micron zirconia particles

    Energy Technology Data Exchange (ETDEWEB)

    Caracoche, M C; Martinez, J A [Departamento de Fisica, IFLP, Facultad de Ciencias Exactas, CICPBA, Universidad Nacional de La Plata (Argentina); Rivas, P C [IFLP-CONICET, Facultad de Ciencias Agrarias y Forestales, Universidad Nacional de La Plata (Argentina); Bondioli, F; Cannillo, V [Dipartimento di Ingegniria dei Materiali e dell' Ambiente, Facolta di Ingegneria, Universita di Modena e Reggio Emilia (Italy); Ferrari, A M, E-mail: cristina@fisica.unlp.edu.a [Dipartimento di Scienza a Metodi dell' Ingegneria, Universita di Modena e Reggio Emilia (Italy)

    2009-05-01

    The Perturbed Angular Correlations technique was used to determine the configurations around Zirconium ions and their thermal behavior in non-aggregated sub-micron zirconia spherical particles. Three residues containing- Zr surroundings were determined for the non-crystalline starting particles, which were identified under the assumption of a certain chemical reactions sequence during synthesis. While the one made up mainly by hydroxyl groups was common to both samples, the two involving mainly organic residues were particle size dependent. Upon crystallization, both samples stabilized in the t'- and t- tetragonal forms and the Xc-cubic form but their amounts and temperatures of appearance were different. On heating, the structure of the smaller particles became gradually monoclinic achieving total degradation upon the subsequent cooling to RT.

  10. Discovering sub-micron ice particles across Dione' surface

    Science.gov (United States)

    Scipioni, Francesca; Schenk, Pual; Tosi, Federico; Clark, Roger; Dalle Ore, Cristina; Combe, Jean-Philippe

    2015-11-01

    Water ice is the most abundant component of Saturn’s mid-sized moons. However, these moons show an albedo asymmetry - their leading sides are bright while their trailing side exhibits dark terrains. Such differences arise from two surface alteration processes: (i) the bombardment of charged particles from the interplanetary medium and driven by Saturn’s magnetosphere on the trailing side, and (ii) the impact of E-ring water ice particles on the satellites’ leading side. As a result, the trailing hemisphere appears to be darker than the leading side. This effect is particularly evident on Dione's surface. A consequence of these surface alteration processes is the formation or the implantation of sub-micron sized ice particles.The presence of such particles influences and modifies the surfaces' spectrum because of Rayleigh scattering by the particles. In the near infrared range of the spectrum, the main sub-micron ice grains spectral indicators are: (i) asymmetry and (ii) long ward minimum shift of the absorption band at 2.02 μm (iii) a decrease in the ratio between the band depths at 1.50 and 2.02 μm (iv) a decrease in the height of the spectral peak at 2.6 μm (v) the suppression of the Fresnel reflection peak at 3.1 μm and (vi) the decrease of the reflection peak at 5 μm relative to those at 3.6 μm.We present results from our ongoing work mapping the variation of sub-micron ice grains spectral indicators across Dione' surface using Cassini-VIMS cubes acquired in the IR range (0.8-5.1 μm). To characterize the global variations of spectral indicators across Dione' surface, we divided it into a 1°x1° grid and then averaged the band depths and peak values inside each square cell.We will investigate if there exist a correspondence with water ice abundance variations by producing water ice' absorption band depths at 1.25, 1.52 and 2.02 μm, and with surface morphology by comparing the results with ISS color maps in the ultraviolet, visible and infrared

  11. Magnetic trapping of superconducting submicron particles produced by laser ablation in superfluid helium

    Science.gov (United States)

    Takahashi, Yuta; Suzuki, Junpei; Yoneyama, Naoya; Tokawa, Yurina; Suzuki, Nobuaki; Matsushima, Fusakazu; Kumakura, Mitsutaka; Ashida, Masaaki; Moriwaki, Yoshiki

    2017-02-01

    We produced spherical superconducting submicron particles by laser ablation of their base metal tips in superfluid helium, and trapped them using a quadrupole magnetic field owing to the diamagnetism caused by the Meissner effect. We also measured their critical temperatures of superconductivity, by observing the threshold temperatures for the confinement of superconducting submicron particles in the trap.

  12. Penetration of sub-micron particles into dentinal tubules using ultrasonic cavitation.

    Science.gov (United States)

    Vyas, N; Sammons, R L; Pikramenou, Z; Palin, W M; Dehghani, H; Walmsley, A D

    2017-01-01

    Functionalised silica sub-micron particles are being investigated as a method of delivering antimicrobials and remineralisation agents into dentinal tubules. However, their methods of application are not optimised, resulting in shallow penetration and aggregation. The aim of this study is to investigate the impact of cavitation occurring around ultrasonic scalers for enhancing particle penetration into dentinal tubules. Dentine slices were prepared from premolar teeth. Silica sub-micron particles were prepared in water or acetone. Cavitation from an ultrasonic scaler (Satelec P5 Newtron, Acteon, France) was applied to dentine slices immersed inside the sub-micron particle solutions. Samples were imaged with scanning electron microscopy (SEM) to assess tubule occlusion and particle penetration. Qualitative observations of SEM images showed some tubule occlusion. The particles could penetrate inside the tubules up to 60μm when there was no cavitation and up to ∼180μm when there was cavitation. The cavitation bubbles produced from an ultrasonic scaler may be used to deliver sub-micron particles into dentine. This method has the potential to deliver such particles deeper into the dentinal tubules. Cavitation from a clinical ultrasonic scaler may enhance penetration of sub-micron particles into dentinal tubules. This can aid in the development of novel methods for delivering therapeutic clinical materials for hypersensitivity relief and treatment of dentinal caries. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Deciphering sub-micron ice particles on Enceladus surface

    Science.gov (United States)

    Scipioni, F.; Schenk, P.; Tosi, F.; D'Aversa, E.; Clark, R.; Combe, J.-Ph.; Ore, C. M. Dalle

    2017-07-01

    The surface of Saturn's moon Enceladus is composed primarily by pure water ice. The Cassini spacecraft has observed present-day geologic activity at the moon's South Polar Region, related with the formation and feeding of Saturn's E-ring. Plumes of micron-sized particles, composed of water ice and other non-ice contaminants (e.g., CO2, NH3, CH4), erupt from four terrain's fractures named Tiger Stripes. Some of this material falls back on Enceladus' surface to form deposits that extend to the North at ∼40°W and ∼220°W, with the highest concentration found at the South Pole. In this work we analyzed VIMS-IR data to identify plumes deposits across Enceladus' surface through the variation in band depth of the main water ice spectral features. To characterize the global variation of water ice band depths across Enceladus, the entire surface was sampled with an angular resolution of 1° in both latitude and longitude, and for each angular bin we averaged the value of all spectral indices as retrieved by VIMS. The position of the plumes' deposits predicted by theoretical models display a good match with water ice band depths' maps on the trailing hemisphere, whereas they diverge significantly on the leading side. Space weathering processes acting on Enceladus' surface ionize and break up water ice molecules, resulting in the formation of particles smaller than one micron. We also mapped the spectral indices for sub-micron particles and we compared the results with the plumes deposits models. Again, a satisfactory match is observed on the trailing hemisphere only. Finally, we investigated the variation of the depth of the water ice absorption bands as a function of the phase angle. In the visible range, some terrains surrounding the Tiger Stripes show a decrease in albedo when the phase angle is smaller than 10°. This unusual effect cannot be confirmed by near infrared data, since observations with a phase angle lower than 10° are not available. For phase angle

  14. A Comprehensive Evaluation of Nanoparticle Tracking Analysis (NanoSight) for Characterization of Proteinaceous Submicron Particles

    NARCIS (Netherlands)

    Tian, X.; Nejadnik, M.R.; Baunsgaard, D.; Henriksen, A.; Rischel, C.; Jiskoot, W.

    2016-01-01

    Nanoparticle tracking analysis (NTA) has attracted great interest for application in the field of submicron particle characterization for biopharmaceuticals. It has the virtue of direct sample visualization and particle-by-particle tracking, but the complexity of method development has limited its

  15. Thermophoretic motion behavior of submicron particles in boundary-layer-separation flow around a droplet.

    Science.gov (United States)

    Wang, Ao; Song, Qiang; Ji, Bingqiang; Yao, Qiang

    2015-12-01

    As a key mechanism of submicron particle capture in wet deposition and wet scrubbing processes, thermophoresis is influenced by the flow and temperature fields. Three-dimensional direct numerical simulations were conducted to quantify the characteristics of the flow and temperature fields around a droplet at three droplet Reynolds numbers (Re) that correspond to three typical boundary-layer-separation flows (steady axisymmetric, steady plane-symmetric, and unsteady plane-symmetric flows). The thermophoretic motion of submicron particles was simulated in these cases. Numerical results show that the motion of submicron particles around the droplet and the deposition distribution exhibit different characteristics under three typical flow forms. The motion patterns of particles are dependent on their initial positions in the upstream and flow forms. The patterns of particle motion and deposition are diversified as Re increases. The particle motion pattern, initial position of captured particles, and capture efficiency change periodically, especially during periodic vortex shedding. The key effects of flow forms on particle motion are the shape and stability of the wake behind the droplet. The drag force of fluid and the thermophoretic force in the wake contribute jointly to the deposition of submicron particles after the boundary-layer separation around a droplet.

  16. Assessment of Sub-Micron Particles by Exploiting Charge Differences with Dielectrophoresis

    Directory of Open Access Journals (Sweden)

    Maria F. Romero-Creel

    2017-08-01

    Full Text Available The analysis, separation, and enrichment of submicron particles are critical steps in many applications, ranging from bio-sensing to disease diagnostics. Microfluidic electrokinetic techniques, such as dielectrophoresis (DEP have proved to be excellent platforms for assessment of submicron particles. DEP is the motion of polarizable particles under the presence of a non-uniform electric field. In this work, the polarization and dielectrophoretic behavior of polystyrene particles with diameters ranging for 100 nm to 1 μm were studied employing microchannels for insulator based DEP (iDEP and low frequency (<1000 Hz AC and DC electric potentials. In particular, the effects of particle surface charge, in terms of magnitude and type of functionalization, were examined. It was found that the magnitude of particle surface charge has a significant impact on the polarization and dielectrophoretic response of the particles, allowing for successful particle assessment. Traditionally, charge differences are exploited employing electrophoretic techniques and particle separation is achieved by differential migration. The present study demonstrates that differences in the particle’s surface charge can also be exploited by means of iDEP; and that distinct types of nanoparticles can be identified by their polarization and dielectrophoretic behavior. These findings open the possibility for iDEP to be employed as a technique for the analysis of submicron biological particles, where subtle differences in surface charge could allow for rapid particle identification and separation.

  17. Nano-ring arrays for sub-micron particle trapping

    Science.gov (United States)

    Han, Xue; Truong, Viet Giang; Nic Chormaic, Síle

    2017-04-01

    Plasmonic tweezers based on nano-ring arrays on gold thin film are demonstrated. A cylindrical surface plasmon resonance is generated in the aperture of a nano-ring and a transmission peak results. When nano-slits are included to connect the nano-rings, the transmission peak becomes narrower. When the size of the aperture of the nano-ring is reduced, this peak is red-shifted. Both 0.5 μm and 1 μm polystyrene particles are trapped successfully by nano-ring arrays. A self-induced back-action effect is observed when a red-shifted laser beam is used. With multiple trapping sites provided by the nano-ring array, this type of plasmonic tweezers has huge potential to be integrated in lab-on-a-chip systems for life sciences research.

  18. Influence of PEG Stoichiometry on Structure-Tuned Formation of Self-Assembled Submicron Nickel Particles

    Directory of Open Access Journals (Sweden)

    Bingxue Pu

    2018-01-01

    Full Text Available Self-assembled submicron nickel particles were successfully synthesized via the one-step surfactant-assisted solvothermal method. The impact of surfactant and reducing agent stoichiometry is investigated in this manuscript. Different morphologies and structures of Ni particles, including flower-like nanoflakes, hydrangea-like structures, chain structures, sphere-like structures, and hollow structures were prepared through different processing conditions with two parameters such as temperature and time. Based on scanning electron microscopy (SEM, X-ray diffraction (XRD, thermal gravimetric analysis (TGA and vibrating sample magnetometry (VSM, the submicron nickel particles show good saturation magnetization and excellent thermal stabilities with a possible growth mechanism for the variety of the structure-tuned formation. Importantly, the microwave absorption properties of the submicron nickel particles were studied. The lowest reflection loss of Ni-P9/T200/H15 with a thin layer thickness of 1.7 mm can reach −42.6 dB at 17.3 GHz.

  19. Strong magnetic response of submicron silicon particles in the infrared

    National Research Council Canada - National Science Library

    García-Etxarri, A; Gómez-Medina, R; Froufe-Pérez, L S; López, C; Chantada, L; Scheffold, F; Aizpurua, J; Nieto-Vesperinas, M; Sáenz, J J

    2011-01-01

    .... However, we find that Silicon particles with index of refraction∼3.5 and radius∼200 nm present strong electric and magnetic dipolar resonances in telecom and near-infrared frequencies, (i.e. at wavelengths≈1.2-2 mm...

  20. Physics of sub-micron cosmic dust particles

    Science.gov (United States)

    Roy, N. L.

    1974-01-01

    Laboratory tests with simulated micrometeoroids to measure the heat transfer coefficient are discussed. Equations for ablation path length for electrically accelerated micrometeoroids entering a gas target are developed which yield guidelines for the laboratory measurement of the heat transfer coefficient. Test results are presented for lanthanum hexaboride (LaB sub 6) microparticles in air, argon, and oxygen targets. The tests indicate the heat transfer coefficient has a value of approximately 0.9 at 30 km/sec, and that it increases to approximately unity at 50 km/sec and above. Test results extend to over 100 km/sec. Results are also given for two types of small particle detectors. A solid state capacitor type detector was tested from 0.61 km/sec to 50 km/sec. An impact ionization type detector was tested from 1.0 to 150 km/sec using LaB sub 6 microparticles.

  1. A Facile Method for Separating and Enriching Nano and Submicron Particles from Titanium Dioxide Found in Food and Pharmaceutical Products.

    Science.gov (United States)

    Faust, James J; Doudrick, Kyle; Yang, Yu; Capco, David G; Westerhoff, Paul

    2016-01-01

    Recent studies indicate the presence of nano-scale titanium dioxide (TiO2) as an additive in human foodstuffs, but a practical protocol to isolate and separate nano-fractions from soluble foodstuffs as a source of material remains elusive. As such, we developed a method for separating the nano and submicron fractions found in commercial-grade TiO2 (E171) and E171 extracted from soluble foodstuffs and pharmaceutical products (e.g., chewing gum, pain reliever, and allergy medicine). Primary particle analysis of commercial-grade E171 indicated that 54% of particles were nano-sized (i.e., particle analysis of five consumer goods intended to be ingested revealed differences in the percent of nano-sized particles from 32%‒58%. Separation and enrichment of nano- and submicron-sized particles from commercial-grade E171 and E171 isolated from foodstuffs and pharmaceuticals was accomplished using rate-zonal centrifugation. Commercial-grade E171 was separated into nano- and submicron-enriched fractions consisting of a nano:submicron fraction of approximately 0.45:1 and 3.2:1, respectively. E171 extracted from gum had nano:submicron fractions of 1.4:1 and 0.19:1 for nano- and submicron-enriched, respectively. We show a difference in particle adhesion to the cell surface, which was found to be dependent on particle size and epithelial orientation. Finally, we provide evidence that E171 particles are not immediately cytotoxic to the Caco-2 human intestinal epithelium model. These data suggest that this separation method is appropriate for studies interested in isolating the nano-sized particle fraction taken directly from consumer products, in order to study separately the effects of nano and submicron particles.

  2. Submicron polycaprolactone particles as a carrier for imaging contrast agent for in vitro applications.

    Science.gov (United States)

    Iqbal, Muhammad; Robin, Sophie; Humbert, Philippe; Viennet, Céline; Agusti, Geraldine; Fessi, Hatem; Elaissari, Abdelhamid

    2015-12-01

    Fluorescent materials have recently attracted considerable attention due to their unique properties and high performance as imaging agent in biomedical fields. Different imaging agents have been encapsulated in order to restrict its delivery to a specific area. In this study, a fluorescent contrast agent was encapsulated for in vitro application by polycaprolactone (PCL) polymer. The encapsulation was performed using modified double emulsion solvent evaporation technique with sonication. Fluorescent nanoparticles (20 nm) were incorporated in the inner aqueous phase of double emulsion. A number of samples were fabricated using different concentrations of fluorescent contrast agent. The contrast agent-containing submicron particle was characterized by a zetasizer for average particle size, SEM and TEM for morphology observations and fluorescence spectrophotometer for encapsulation efficiency. Moreover, contrast agent distribution in the PCL matrix was determined by confocal microscopy. The incorporation of contrast agent in different concentrations did not affect the physicochemical properties of PCL particles and the average size of encapsulated particles was found to be in the submicron range. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Cefquinome Controlled Size Submicron Particles Precipitation by SEDS Process Using Annular Gap Nozzle

    Directory of Open Access Journals (Sweden)

    Kefeng Xiao

    2017-01-01

    Full Text Available An annular gap nozzle was applied in solution enhanced dispersion by supercritical fluids (SEDS process to prepare cefquinome controlled size submicron particles so as to enhance their efficacy. Analysis results of orthogonal experiments indicated that the concentration of solution was the primary factor to affect particle sizes in SEDS process, and feeding speed of solution, precipitation pressure, and precipitation temperature ranked second to fourth. Meanwhile, the optimal operating conditions were that solution concentration was 100 mg/mL, feeding speed was 9 mL/min, precipitation pressure was 10 MPa, and precipitation temperature was 316 K. The confirmatory experiment showed that D50 of processed cefquinome particles in optimal operating conditions was 0.73 μm. Moreover, univariate effect analysis showed that the cefquinome particle size increased with the increase of concentration of the solution or precipitation pressure but decreased with the increase of solution feeding speed. When precipitation temperature increased, the cefquinome particle size showed highest point. Moreover, characterization of processed cefquinome particles was analyzed by SEM, FT-IR, and XRD. Analysis results indicated that the surface appearance of processed cefquinome particles was flakes. The chemical structure of processed cefquinome particles was not changed, and the crystallinity of processed cefquinome particles was a little lower than that of raw cefquinome particles.

  4. Submicron particle mass concentrations and sources in the Amazonian wet season (AMAZE-08)

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Q.; Farmer, D. K.; Rizzo, L. V.; Pauliqueivis, T.; Kuwata, Mikinori; Karl, Thomas G.; Guenther, Alex B.; Allan, James D.; Coe, H.; Andreae, M. O.; Poeschl, U.; Jiminez, J. L.; Artaxo, Paulo; Martin, Scot T.

    2015-01-01

    Real-time mass spectra of non-refractory component of submicron aerosol particles were recorded in a tropical rainforest in the central Amazon basin during the wet season of 2008, as a part of the Amazonian Aerosol Characterization Experiment (AMAZE-08). Organic components accounted on average for more than 80% of the non-refractory submicron particle mass concentrations during the period of measurements. Ammonium was present in sufficient quantities to halfway neutralize sulfate. In this acidic, isoprene-dominated, low-NOx environment the high-resolution mass spectra as well as mass closures with ion chromatography measurements did not provide evidence for significant contributions of organosulfate species, at least at concentrations above uncertainty levels. Positive-matrix factorization of the time series of particle mass spectra identified four statistical factors to account for the variance of the signal intensities of the organic constituents: a factor HOA having a hydrocarbon-like signature and identified as regional emissions of primary organic material, a factor OOA-1 associated with fresh production of secondary organic material by a mechanism of BVOC oxidation followed by gas-to-particle conversion, a factor OOA-2 consistent with reactive uptake of isoprene oxidation products, especially epoxydiols by acidic particles, and a factor OOA-3 associated with long range transport and atmospheric aging. The OOA-1, -2, and -3 factors had progressively more oxidized signatures. Diameter-resolved mass spectral markers also suggested enhanced reactive uptake of isoprene oxidation products to the accumulation mode for the OOA-2 factor, and such size partitioning can be indicative of in-cloud process. The campaign-average factor loadings were in a ratio of 1.1:1.0 for the OOA-1 compared to the OOA-2 pathway, suggesting the comparable importance of gas-phase compared to particle-phase (including cloud waters) production pathways of secondary organic material during

  5. The role of jet and film drops in controlling the mixing state of submicron sea spray aerosol particles

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Xiaofei; Deane, Grant B.; Moore, Kathryn A.; Ryder, Olivia S.; Stokes, M. Dale; Beall, Charlotte M.; Collins, Douglas B.; Santander, Mitchell V.; Burrows, Susannah M.; Sultana, Camille M.; Prather, Kimberly A.

    2017-06-19

    Covering 71% of the Earth’s surface, oceans represent a significant global source of atmospheric aerosols. The size and composition of sea spray aerosols (SSA) affect their ability to serve as cloud seeds and thus understanding the factors controlling their composition is critical to predicting their impact on clouds and climate. SSA particles have been shown to be an external mixture of particles with different compositions. Film and jet drop production mechanisms ultimately determine the individual particle compositions which are comprised of an array of salt/organic mixtures ranging from pure sea salt to nearly pure organic particles. It is often assumed that the majority of submicron SSA are formed by film drops produced from bursting hydrophobic organic-rich bubble film caps at the sea surface, and in contrast, jet drops are postulated to produce larger supermicron particles from underlying seawater comprised largely of salts and water soluble organic species. However, here we show that jet drops produced by bursting sub-100 m bubbles account for up to 40 % of all submicron particles. They have distinct chemical compositions, organic volume fractions and ice nucleating activities from submicron film drops. Thus a substantial fraction of submicron particles will not necessarily be controlled by the composition of the sea surface microlayer as has been assumed in many studies. This finding has significant ramifications for the size-resolved mixing states of SSA particles which must be taken into consideration when accessing SSA impacts on clouds.

  6. Submicron particle mass concentrations and sources in the Amazonian wet season (AMAZE-08)

    Science.gov (United States)

    Chen, Q.; Farmer, D. K.; Rizzo, L. V.; Pauliquevis, T.; Kuwata, M.; Karl, T. G.; Guenther, A.; Allan, J. D.; Coe, H.; Andreae, M. O.; Pöschl, U.; Jimenez, J. L.; Artaxo, P.; Martin, S. T.

    2015-04-01

    Real-time mass spectra of the non-refractory species in submicron aerosol particles were recorded in a tropical rainforest in the central Amazon Basin during the wet season from February to March 2008, as a part of the Amazonian Aerosol Characterization Experiment (AMAZE-08). Organic material accounted on average for more than 80% of the non-refractory submicron particle mass concentrations during the period of measurements. There was insufficient ammonium to neutralize sulfate. In this acidic, isoprene-rich, HO2-dominant environment, positive-matrix factorization of the time series of particle mass spectra identified four statistical factors to account for the 99% of the variance in the signal intensities of the organic constituents. The first factor was identified as associated with regional and local pollution and labeled "HOA" for its hydrocarbon-like characteristics. A second factor was associated with long-range transport and labeled "OOA-1" for its oxygenated characteristics. A third factor, labeled "OOA-2," was implicated as associated with the reactive uptake of isoprene oxidation products, especially of epoxydiols to acidic haze, fog, or cloud droplets. A fourth factor, labeled "OOA-3," was consistent with an association with the fresh production of secondary organic material (SOM) by the mechanism of gas-phase oxidation of biogenic volatile organic precursors followed by gas-to-particle conversion of the oxidation products. The suffixes 1, 2, and 3 on the OOA labels signify ordinal ranking with respect to the extent of oxidation represented by the factor. The process of aqueous-phase oxidation of water-soluble products of gas-phase photochemistry might also have been associated to some extent with the OOA-2 factor. The campaign-average factor loadings had a ratio of 1.4:1 for OOA-2 : OOA-3, suggesting the comparable importance of particle-phase compared to gas-phase pathways for the production of SOM during the study period.

  7. Thermal, structural and morphological properties of High Density Polyethylene matrix composites reinforced with submicron agro silica particles and Titania particles

    Directory of Open Access Journals (Sweden)

    Oluyemi O. Daramola

    2017-07-01

    Full Text Available HDPE—based composites samples filled with 2, 4, 6, 8 and 10 wt.% submicron agro-waste silica particles extracted from rice husk ash (RHA at constant 0.3 wt.% Titania loading were prepared using rapra single screw extruder at temperature of 200–230 °C. The extrudates were compressed with a laboratory carver press at a temperature of 230 °C for 10 min under applied pressure of 0.2 kPa and water cooled at 20 °C min−1. Thermal, structural and morphological properties of the composites were studied. The results of the thermogravimetric analysis (TGA revealed that the composites with 10 wt.% SiO2 have the best maximum thermal degradation temperature of 438.73 °C. The crystal structure of neat HDPE, and the siliceous composites developed revealed two obvious diffractive peaks of about 21.3° and 23.7° corresponding to typical crystal plane (1 1 0 and (2 0 0 of orthorhombic phase respectively. The diffractive peaks do not shift with the addition of silica particles; this clearly indicates that the addition of silica particles did not exert much effect on the crystalline structure of HDPE. There is no much difference in the interplanar distance (d-value. Lamellar thickness (L of HDPE increases with the addition of silica particles, which implies that silica particles aid the formation of more perfect crystals. Scanning electron microscopy studies indicated that there were chains inter diffusion and entanglement between HDPE matrix and the silica particles at lower weight fraction (2–4 wt.% of submicron silica particles which resulted into homogeneous dispersion of the particles within the matrix.

  8. Synthesis of gelatin nano/submicron particles by binary nonsolvent aided coacervation (BNAC) method.

    Science.gov (United States)

    Patra, Shamayita; Basak, Piyali; Tibarewala, D N

    2016-02-01

    A newly developed modified coacervation method is utilized to synthesize gelatin nano/submicron particles (GN/SPs) as a drug carrier. Binary nonsolvent aided coacervation (BNAC) method is a modified single step coacervation method, which has yielded approximately a threefold lower particle size and higher average yield in terms of weight percentage of around 94% in comparison to the conventional phase separation methods. In this study 0.5% (w/v) gelatin aqueous solution with a binary nonsolvent system of acetone and ethanol was used. Nanoparticle synthesis was optimized with respect to nonsolvent system type and pH. pH7 has resulted a minimum particle size of 55.67 (±43.74) nm in anhydrous medium along with a swollen particle size of 776nm (±38.57) in aqueous medium with a zeta potential of (-16.3±3.51) mV in aqueous medium. Swelling ratio of 13.95 confirms the crosslinked hydrogel nature of the particles. Furthermore, drug loading efficiency of the gelatin particles prepared at 7pH was observed with nitrofurazone as the model drug. Results of drug release study indicate the potential use of GN/SPs as drug loading matrix for wound management such as burn wound management. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Quantitative cellular uptake of double fluorescent core-shelled model submicronic particles

    Energy Technology Data Exchange (ETDEWEB)

    Leclerc, Lara, E-mail: leclerc@emse.fr [Ecole Nationale Superieure des Mines, CIS-EMSE, LINA (France); Boudard, Delphine [LINA (France); Pourchez, Jeremie; Forest, Valerie [Ecole Nationale Superieure des Mines, CIS-EMSE, LINA (France); Marmuse, Laurence; Louis, Cedric [NANO-H S.A.S (France); Bin, Valerie [LINA (France); Palle, Sabine [Universite Jean Monnet, Centre de Microscopie Confocale Multiphotonique (France); Grosseau, Philippe; Bernache-Assollant, Didier [Ecole Nationale Superieure des Mines, CIS-EMSE, LINA (France); Cottier, Michele [LINA (France)

    2012-11-15

    The relationship between particles' physicochemical parameters, their uptake by cells and their degree of biological toxicity represent a crucial issue, especially for the development of new technologies such as fabrication of micro- and nanoparticles in the promising field of drug delivery systems. This work was aimed at developing a proof-of-concept for a novel model of double fluorescence submicronic particles that could be spotted inside phagolysosomes. Fluorescein isothiocyanate (FITC) particles were synthesized and then conjugated with a fluorescent pHrodo Trade-Mark-Sign probe, red fluorescence of which increases in acidic conditions such as within lysosomes. After validation in acellular conditions by spectral analysis with confocal microscopy and dynamic light scattering, quantification of phagocytosis was conducted on a macrophage cell line in vitro. The biological impact of pHrodo functionalization (cytotoxicity, inflammatory response, and oxidative stress) was also investigated. Results validate the proof-of-concept of double fluorescent particles (FITC + pHrodo), allowing detection of entirely engulfed pHrodo particles (green and red labeling). Moreover incorporation of pHrodo had no major effects on cytotoxicity compared to particles without pHrodo, making them a powerful tool for micro- and nanotechnologies.

  10. Minimizing biases associated with tracking analysis of submicron particles in heterogeneous biological fluids.

    Science.gov (United States)

    Wang, Ying-Ying; Nunn, Kenetta L; Harit, Dimple; McKinley, Scott A; Lai, Samuel K

    2015-12-28

    Tracking the dynamic motion of individual nanoparticles or viruses offers quantitative insights into their real-time behavior and fate in different biological environments. Indeed, particle tracking is a powerful tool that has facilitated the development of drug carriers with enhanced penetration of mucus, brain tissues and other extracellular matrices. Nevertheless, heterogeneity is a hallmark of nanoparticle diffusion in such complex environments: identical particles can exhibit strongly hindered or unobstructed diffusion within microns of each other. The common practice in 2D particle tracking, namely analyzing all trackable particle traces with equal weighting, naturally biases towards rapidly diffusing sub-populations at shorter time scales. This in turn results in misrepresentation of particle behavior and a systematic underestimate of the time necessary for a population of nanoparticles to diffuse specific distances. We show here via both computational simulation and experimental data that this bias can be rigorously corrected by weighing the contribution by each particle trace on a 'frame-by-frame' basis. We believe this methodology presents an important step towards objective and accurate assessment of the heterogeneous transport behavior of submicron drug carriers and pathogens in biological environments. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Analysis of major air pollutants and submicron particles in New York City and Long Island

    Science.gov (United States)

    Masiol, M.; Hopke, P. K.; Felton, H. D.; Frank, B. P.; Rattigan, O. V.; Wurth, M. J.; LaDuke, G. H.

    2017-01-01

    A year-long sampling campaign of major air pollutants and submicron particle number size distributions was conducted at two sites taken as representative of city-wide air quality in New York City and Long Island, respectively. A number of species were quantified with hourly time resolution, including particle number concentrations in 6 size ranges (20-30 nm, 30-50 nm, 50-70 nm, 70-100 nm, 100-200 nm, and >200 nm), nitrogen oxides, sulfur dioxide, ozone, carbon monoxide, methane, non-methane hydrocarbons, PM2.5 mass concentration and some PM major components (sulfate, organic and elemental carbon). Hourly concentrations of primary and secondary organic carbon were estimated using the EC tracer method. Data were matched with weather parameters and air parcel back-trajectories. A series of tools were thus applied to: (i) study the seasonal, weekly, diurnal cycles of pollutants; (ii) investigate the relationships amongst pollutants through correlation and lagged correlation analyses; (iii) depict the role of atmospheric photochemical processes; (iv) examine the location of the potential sources by mean of conditional bivariate probability function analysis and (v) investigate the role of regional transport of air masses to the concentrations of analyzed species. Results indicate that concentrations of NOx, SO2, CO, non-methane hydrocarbons, primary OC and EC are predominantly determined by local sources, but are also affected by regional transports of polluted air masses. On the contrary, the transport of continental polluted air masses has a main effect in raising the concentrations of secondary PM2.5 (sulfate and secondary organic carbon). By providing direct information on the concentrations and trends of key pollutants and submicron particle number concentrations, this study finally enables some general considerations about air quality status and atmospheric processes over the New York City metropolitan area.

  12. Formation of stable submicron peptide or protein particles by thin film freezing

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, Keith P.; Engstrom, Joshua; Williams, III, Robert O.

    2017-04-18

    The present invention includes compositions and methods for preparing micron-sized or submicron-sized particles by dissolving a water soluble effective ingredient in one or more solvents; spraying or dripping droplets solvent such that the effective ingredient is exposed to a vapor-liquid interface of less than 50, 100, 150, 200, 250, 200, 400 or 500 cm.sup.-1 area/volume to, e.g., increase protein stability; and contacting the droplet with a freezing surface that has a temperature differential of at least 30.degree. C. between the droplet and the surface, wherein the surface freezes the droplet into a thin film with a thickness of less than 500 micrometers and a surface area to volume between 25 to 500 cm.sup.-1.

  13. Bacterial characterization in ambient submicron particles during severe haze episodes at Ji'nan, China.

    Science.gov (United States)

    Xu, Caihong; Wei, Min; Chen, Jianmin; Wang, Xinfeng; Zhu, Chao; Li, Jiarong; Zheng, Lulu; Sui, Guodong; Li, Weijun; Wang, Wenxing; Zhang, Qingzhu; Mellouki, Abdelwahid

    2017-02-15

    In January 2014, severe haze episodes which sweep across Chinese cities have attracted public concern and interest at home and abroad. In addition to the physicochemical properties of air pollutants, bacteria are thought to be responsible for the spread of respiratory diseases and various allergies. We attempted the bacterial characterization of submicron particles (PM 0.18-0.32 , PM 0.32-0.56 , and PM 0.56-1 ) under severe haze episodes using high-throughput sequencing and real-time quantitative PCR detecting system based on 21 samples collected from January to March 2014 at Ji'nan, China. The high bacterial concentration in PM 0.32-0.56 (7314cells m -3 ), PM 0.18-0.32 (7212cells m -3 ), and PM 0.56-1 (6982cells m -3 ) showed significant negative correlations with SO 2 , NO 2, and O 3 . Under sufficient sequencing depth, 37 phyla, 71 classes, 137 orders, 236 families, and 378 genera were classified, and the bacterial community structure varied significantly in different size fractions. For example, Holophagaceae (Acidobacteria) in PM 0.32-0.56 showed 6-fold higher abundance than that in PM 0.18-0.32 . Moreover, functional categories and bacterial species (Lactococcus piscium, Pseudomonas fragi, Streptococcus agalactiae, and Pseudomonas cichorii) that may potentially be responsible for infections and allergies were also discovered. Source track analysis showed that the ambient bacteria mainly originated from soils, leaf surfaces, and feces. Our results highlighted the importance of airborne microbial communities by understanding the concentration, structure, ecological and health effects, especially those in submicron particles during haze episodes. Copyright © 2016. Published by Elsevier B.V.

  14. Size-Dependent Photodynamic Anticancer Activity of Biocompatible Multifunctional Magnetic Submicron Particles in Prostate Cancer Cells

    Directory of Open Access Journals (Sweden)

    Kyong-Hoon Choi

    2016-09-01

    Full Text Available In this study, newly designed biocompatible multifunctional magnetic submicron particles (CoFe2O4-HPs-FAs of well-defined sizes (60, 133, 245, and 335 nm were fabricated for application as a photosensitizer delivery agent for photodynamic therapy in cancer cells. To provide selective targeting of cancer cells and destruction of cancer cell functionality, basic cobalt ferrite (CoFe2O4 particles were covalently bonded with a photosensitizer (PS, which comprises hematoporphyrin (HP, and folic acid (FA molecules. The magnetic properties of the CoFe2O4 particles were finely adjusted by controlling the size of the primary CoFe2O4 nanograins, and secondary superstructured composite particles were formed by aggregation of the nanograins. The prepared CoFe2O4-HP-FA exhibited high water solubility, good MR-imaging capacity, and biocompatibility without any in vitro cytotoxicity. In particular, our CoFe2O4-HP-FA exhibited remarkable photodynamic anticancer efficiency via induction of apoptotic death in PC-3 prostate cancer cells in a particle size- and concentration-dependent manner. This size-dependent effect was determined by the specific surface area of the particles because the number of HP molecules increased with decreasing size and increasing surface area. These results indicate that our CoFe2O4-HP-FA may be applicable for photodynamic therapy (PDT as a PS delivery material and a therapeutic agent for MR-imaging based PDT owing to their high saturation value for magnetization and superparamagnetism.

  15. The role of adsorbed water on the friction of a layer of submicron particles

    Science.gov (United States)

    Sammis, Charles G.; Lockner, David A.; Reches, Ze’ev

    2011-01-01

    Anomalously low values of friction observed in layers of submicron particles deformed in simple shear at high slip velocities are explained as the consequence of a one nanometer thick layer of water adsorbed on the particles. The observed transition from normal friction with an apparent coefficient near μ = 0.6 at low slip speeds to a coefficient near μ = 0.3 at higher slip speeds is attributed to competition between the time required to extrude the water layer from between neighboring particles in a force chain and the average lifetime of the chain. At low slip speeds the time required for extrusion is less than the average lifetime of a chain so the particles make contact and lock. As slip speed increases, the average lifetime of a chain decreases until it is less than the extrusion time and the particles in a force chain never come into direct contact. If the adsorbed water layer enables the otherwise rough particles to rotate, the coefficient of friction will drop to μ = 0.3, appropriate for rotating spheres. At the highest slip speeds particle temperatures rise above 100°C, the water layer vaporizes, the particles contact and lock, and the coefficient of friction rises to μ = 0.6. The observed onset of weakening at slip speeds near 0.001 m/s is consistent with the measured viscosity of a 1 nm thick layer of adsorbed water, with a minimum particle radius of approximately 20 nm, and with reasonable assumptions about the distribution of force chains guided by experimental observation. The reduction of friction and the range of velocities over which it occurs decrease with increasing normal stress, as predicted by the model. Moreover, the analysis predicts that this high-speed weakening mechanism should operate only for particles with radii smaller than approximately 1 μm. For larger particles the slip speed required for weakening is so large that frictional heating will evaporate the adsorbed water and weakening will not occur.

  16. Water ice and sub-micron ice particles on Tethys and Mimas

    Science.gov (United States)

    Scipioni, Francesca; Nordheim, Tom; Clark, Roger Nelson; D'Aversa, Emiliano; Cruikshank, Dale P.; Tosi, Federico; Schenk, Paul M.; Combe, Jean-Philippe; Dalle Ore, Cristina M.

    2017-10-01

    IntroductionWe present our ongoing work, mapping the variation of the main water ice absorption bands, and the distribution of the sub-micron particles, across Mimas and Tethys’ surfaces using Cassini-VIMS cubes acquired in the IR range (0.8-5.1 μm). We present our results in the form of maps of variation of selected spectral indicators (depth of absorption bands, reflectance peak height, spectral slopes).Data analysisVIMS acquires hyperspectral data in the 0.3-5.1 μm spectral range. We selected VIMS cubes of Tethys and Mimas in the IR range (0.8-5.1 μm). For all pixels in the selected cubes, we measured the band depths for water-ice absorptions at 1.25, 1.5 and 2.02 μm and the height of the 3.6 μm reflection peak. Moreover, we considered the spectral indictors for particles smaller than 1 µm [1]: (i) the 2 µm absorption band is asymmetric and (ii) it has the minimum shifted to longer λ (iii) the band depth ratio 1.5/2.0 µm decreases; (iv) the reflection peak at 2.6 µm decreases; (v) the Fresnel reflection peak is suppressed; (vi) the 5 µm reflectance is decreased relative to the 3.6 µm peak. To characterize the global variation of water-ice band depths, and of sub-micron particles spectral indicators, across Mimas and Tethys, we sampled the two satellites’ surfacees with a 1°x1° fixed-resolution grid and then averaged the band depths and peak values inside each square cell.3. ResultsFor both moons we find that large geologic features, such as the Odysseus and Herschel impact basins, do not correlate with water ice’s abundance variation. For Tethys, we found a quite uniform surface on both hemispheres. The only deviation from this pattern shows up on the trailing hemisphere, where we notice two north-oriented, dark areas around 225° and 315°. For Mimas, the leading and trailing hemispheres appear to be quite similar in water ice abundance, the trailing portion having water ice absorption bands lightly more suppressed than the leading side

  17. A comparative study of submicron particle sizing platforms: accuracy, precision and resolution analysis of polydisperse particle size distributions.

    Science.gov (United States)

    Anderson, Will; Kozak, Darby; Coleman, Victoria A; Jämting, Åsa K; Trau, Matt

    2013-09-01

    The particle size distribution (PSD) of a polydisperse or multimodal system can often be difficult to obtain due to the inherent limitations in established measurement techniques. For this reason, the resolution, accuracy and precision of three new and one established, commercially available and fundamentally different particle size analysis platforms were compared by measuring both individual and a mixed sample of monodisperse, sub-micron (220, 330, and 410 nm - nominal modal size) polystyrene particles. The platforms compared were the qNano Tunable Resistive Pulse Sensor, Nanosight LM10 Particle Tracking Analysis System, the CPS Instruments's UHR24000 Disc Centrifuge, and the routinely used Malvern Zetasizer Nano ZS Dynamic Light Scattering system. All measurements were subjected to a peak detection algorithm so that the detected particle populations could be compared to 'reference' Transmission Electron Microscope measurements of the individual particle samples. Only the Tunable Resistive Pulse Sensor and Disc Centrifuge platforms provided the resolution required to resolve all three particle populations present in the mixed 'multimodal' particle sample. In contrast, the light scattering based Particle Tracking Analysis and Dynamic Light Scattering platforms were only able to detect a single population of particles corresponding to either the largest (410 nm) or smallest (220 nm) particles in the multimodal sample, respectively. When the particle sets were measured separately (monomodal) each platform was able to resolve and accurately obtain a mean particle size within 10% of the Transmission Electron Microscope reference values. However, the broadness of the PSD measured in the monomodal samples deviated greatly, with coefficients of variation being ~2-6-fold larger than the TEM measurements across all four platforms. The large variation in the PSDs obtained from these four, fundamentally different platforms, indicates that great care must still be taken in

  18. Number size distributions and seasonality of submicron particles in Europe 2008-2009

    Science.gov (United States)

    Asmi, A.; Wiedensohler, A.; Laj, P.; Fjaeraa, A.-M.; Sellegri, K.; Birmili, W.; Weingartner, E.; Baltensperger, U.; Zdimal, V.; Zikova, N.; Putaud, J.-P.; Marinoni, A.; Tunved, P.; Hansson, H.-C.; Fiebig, M.; Kivekäs, N.; Lihavainen, H.; Asmi, E.; Ulevicius, V.; Aalto, P. P.; Swietlicki, E.; Kristensson, A.; Mihalopoulos, N.; Kalivitis, N.; Kalapov, I.; Kiss, G.; de Leeuw, G.; Henzing, B.; Harrison, R. M.; Beddows, D.; O'Dowd, C.; Jennings, S. G.; Flentje, H.; Weinhold, K.; Meinhardt, F.; Ries, L.; Kulmala, M.

    2011-06-01

    Two years of harmonized aerosol number size distribution data from 24 European field monitoring sites have been analysed. The results give a comprehensive overview of the European near surface aerosol particle number concentrations and number size distributions between 30 and 500 nm of dry particle diameter. Spatial and temporal distribution of aerosols in the particle sizes most important for climate applications are presented. We also analyse the annual, weekly and diurnal cycles of the aerosol number concentrations, provide log-normal fitting parameters for median number size distributions, and give guidance notes for data users. Emphasis is placed on the usability of results within the aerosol modelling community. We also show that the aerosol number concentrations of Aitken and accumulation mode particles (with 100 nm dry diameter as a cut-off between modes) are related, although there is significant variation in the ratios of the modal number concentrations. Different aerosol and station types are distinguished from this data and this methodology has potential for further categorization of stations aerosol number size distribution types. The European submicron aerosol was divided into characteristic types: Central European aerosol, characterized by single mode median size distributions, unimodal number concentration histograms and low variability in CCN-sized aerosol number concentrations; Nordic aerosol with low number concentrations, although showing pronounced seasonal variation of especially Aitken mode particles; Mountain sites (altitude over 1000 m a.s.l.) with a strong seasonal cycle in aerosol number concentrations, high variability, and very low median number concentrations. Southern and Western European regions had fewer stations, which decreases the regional coverage of these results. Aerosol number concentrations over the Britain and Ireland had very high variance and there are indications of mixed air masses from several source regions; the

  19. Sub-micron particle number size distribution characteristics at two urban locations in Leicester

    Science.gov (United States)

    Hama, Sarkawt M. L.; Cordell, Rebecca L.; Kos, Gerard P. A.; Weijers, E. P.; Monks, Paul S.

    2017-09-01

    The particle number size distribution (PNSD) of atmospheric particles not only provides information about sources and atmospheric processing of particles, but also plays an important role in determining regional lung dose. Owing to the importance of PNSD in understanding particulate pollution two short-term campaigns (March-June 2014) measurements of sub-micron PNSD were conducted at two urban background locations in Leicester, UK. At the first site, Leicester Automatic Urban Rural Network (AURN), the mean number concentrations of nucleation, Aitken, accumulation modes, the total particles, equivalent black carbon (eBC) mass concentrations were 2002, 3258, 1576, 6837 # cm-3, 1.7 μg m-3, respectively, and at the second site, Brookfield (BF), were 1455, 2407, 874, 4737 # cm-3, 0.77 μg m-3, respectively. The total particle number was dominated by the nucleation and Aitken modes, with both consisting of 77%, and 81% of total number concentrations at AURN and BF sites, respectively. This behaviour could be attributed to primary emissions (traffic) of ultrafine particles and the temporal evolution of mixing layer. The size distribution at the AURN site shows bimodal distribution at 22 nm with a minor peak at 70 nm. The size distribution at BF site, however, exhibits unimodal distribution at 35 nm. This study has for the first time investigated the effect of Easter holiday on PNSD in UK. The temporal variation of PNSD demonstrated a good degree of correlation with traffic-related pollutants (NOX, and eBC at both sites). The meteorological conditions, also had an impact on the PNSD and eBC at both sites. During the measurement period, the frequency of NPF events was calculated to be 13.3%, and 22.2% at AURN and BF sites, respectively. The average value of formation and growth rates of nucleation mode particles were 1.3, and 1.17 cm-3 s-1 and 7.42, and 5.3 nm h-1 at AURN, and BF sites, respectively. It can suggested that aerosol particles in Leicester originate mainly

  20. Measurements of Submicron Particle Adsorption and Particle Film Elasticity at Oil-Water Interfaces.

    Science.gov (United States)

    Manga, Mohamed S; Hunter, Timothy N; Cayre, Olivier J; York, David W; Reichert, Matthew D; Anna, Shelly L; Walker, Lynn M; Williams, Richard A; Biggs, Simon R

    2016-05-03

    The influence of particle adsorption on liquid/liquid interfacial tension is not well understood, and much previous research has suggested conflicting behaviors. In this paper we investigate the surface activity and adsorption kinetics of charge stabilized and pH-responsive polymer stabilized colloids at oil/water interfaces using two tensiometry techniques: (i) pendant drop and (ii) microtensiometer. We found, using both techniques, that charge stabilized particles had little or no influence on the (dynamic) interfacial tension, although dense silica particles affected the "apparent" measured tension in the pendent drop, due to gravity driven elongation of the droplet profile. Nevertheless, this apparent change additionally allowed the study of adsorption kinetics, which was related qualitatively between particle systems by estimated diffusion coefficients. Significant and real interfacial tension responses were measured using ∼53 nm core-shell latex particles with a pH-responsive polymer stabilizer of poly(methyl methacrylate)-b-poly(2-(dimethylamino)ethyl methacrylate) (pMMA-b-pDMAEMA) diblock copolymer. At pH 2, where the polymer is strongly charged, behavior was similar to that of the bare charge-stabilized particles, showing little change in the interfacial tension. At pH 10, where the polymer is discharged and poorly soluble in water, a significant decrease in the measured interfacial tension commensurate with strong adsorption at the oil-water interface was seen, which was similar in magnitude to the surface activity of the free polymer. These results were both confirmed through droplet profile and microtensiometry experiments. Dilational elasticity measurements were also performed by oscillation of the droplet; again, changes in interfacial tension with droplet oscillation were only seen with the responsive particles at pH 10. Frequency sweeps were performed to ascertain the dilational elasticity modulus, with measured values being significantly higher

  1. Neurotoxicity of low-dose repeatedly intranasal instillation of nano- and submicron-sized ferric oxide particles in mice

    Energy Technology Data Exchange (ETDEWEB)

    Wang Bing; Feng Weiyue, E-mail: fengwy@mail.ihep.ac.cn; Zhu Motao; Wang Yun; Wang Meng [Chinese Academy of Sciences, Laboratory for Bio-Environmental Effects of Nanomaterials and Nanosafety and Key Laboratory of Nuclear Analytical Techniques, Institute of High Energy Physics (China); Gu Yiqun [Maternity Hospital of Haidian District (China); Ouyang Hong; Wang Huajian; Li Ming; Zhao Yuliang, E-mail: zhaoyuliang@mail.ihep.ac.cn; Chai Zhifang [Chinese Academy of Sciences, Laboratory for Bio-Environmental Effects of Nanomaterials and Nanosafety and Key Laboratory of Nuclear Analytical Techniques, Institute of High Energy Physics (China); Wang Haifang [Peking University, College of Chemistry and Molecular Engineering (China)

    2009-01-15

    Olfactory tract has been demonstrated to be an important portal for inhaled solid nanoparticle transportation into the central nervous system (CNS). We have previously demonstrated that intranasally instilled Fe{sub 2}O{sub 3} nanoparticles could transport into the CNS via olfactory pathway. In this study, we investigated the neurotoxicity and size effect of repeatedly low-dose (130 {mu}g) intranasal exposure of nano- and submicron-sized Fe{sub 2}O{sub 3} particles (21 nm and 280 nm) to mice. The biomarkers of oxidative stress, activity of nitric oxide synthases and release of monoamine neurotransmitter in the brain were studied. Our results showed that significant oxidative stress was induced by the two sizes of Fe{sub 2}O{sub 3} particles. The activities of GSH-Px, Cu,Zn-SOD, and cNOS significantly elevated and the total GSH and GSH/GSSG ratio significantly decreased in the olfactory bulb and hippocampus after the nano- and submicron-sized Fe{sub 2}O{sub 3} particle treatment (p < 0.05). The nano-sized Fe{sub 2}O{sub 3} generally induced greater alteration and more significant dose-effect response than the submicron-sized particle did. Some slight perturbation of monoamine neurotransmitters were found in the hippocampus after exposure to the two sizes of Fe{sub 2}O{sub 3} particle. The TEM image showed that some ultrastructural alterations in nerve cells, including neurodendron degeneration, membranous structure disruption and lysosome increase in the olfactory bulb, slight dilation in the rough endoplasmic reticulum and lysosome increase in the hippocampus were induced by the nano-sized Fe{sub 2}O{sub 3} treatment. In contrast, in the submicron-sized Fe{sub 2}O{sub 3} treated mice, slightly swollen mitochondria and some vacuoles were observed in the olfactory bulb and hippocampus, respectively. These results indicate that intranasal exposure of Fe{sub 2}O{sub 3} nanoparticles could induce more severe oxidative stress and nerve cell damage in the brain than the

  2. Submicron Particles during Macro- and Micro-Weldings Procedures in Industrial Indoor Environments and Health Implications for Welding Operators

    Directory of Open Access Journals (Sweden)

    Pasquale Avino

    2015-06-01

    Full Text Available One of the emerging risks in the engineering and electronic industries is the exposure of workers to ultrafine particles during (micro-welding operations, i.e., processes used for joining two metal parts heated locally, which constitute the base metal, with or without addition of another metal which is the filler metal, melted between the edges to be joined. The process is accompanied by formation of metallic fumes arising from the molten metal as well as by the emission of metal fumes of variable composition depending on the alloys welded and fused. The aim of this paper is to investigate the number, concentration and size distribution of submicron particles produced by (micro-welding processes. Particle number size distribution is continuously measured during (micro-welding operations by means of two instruments, i.e., Fast Mobility Particle Sizer and Nanoparticle Surface Area Monitor. The temporal variation of the particle number size distribution across the peaks evidences the strong and fast-evolving contribution of nucleation mode particles: peak values are maintained for less than 10 s. The implication of such contribution on human health is linked to the high deposition efficiency of submicronic particles in the alveolar interstitial region of the human respiratory system, where gas exchange occurs.

  3. Heated submicron particle fluxes using an optical particle counter in urban environment

    Directory of Open Access Journals (Sweden)

    M. Vogt

    2013-03-01

    Full Text Available From May 2008 to March 2009 aerosol emissions were measured using the eddy covariance method covering the size range 0.25 to 2.5 μm diameter (Dp from a 105 m tower, in central Stockholm, Sweden. Supporting chemical aerosol data were collected at roof and street level. Results show that the inorganic fraction of sulfate, nitrate, ammonium and sea salt accounts for approximately 15% of the total aerosol mass Dp (PM1 with water soluble soil contributing 11% and water insoluble soil 47%. Carbonaceous compounds were at the most 27% of PM1 mass. It was found that heating the air from the tower to 200 °C resulted in the loss of approximately 60% of the aerosol volume at 0.25 μm Dp whereas only 40% of the aerosol volume was removed at 0.6 μm Dp. Further heating to 300 °C caused very little additional losses Dp. The chemical analysis did not include carbonaceous compounds, but based on the difference between the total mass concentration and the sum of the analyzed non-carbonaceous materials, it can be assumed that the non-volatile particulate material (heated to 300 °C consists mainly of carbonaceous compounds, including elemental carbon. Furthermore, it was found that the non-volatile particle fraction Dp correlated (r2 = 0.4 with the BC concentration at roof level in the city, supporting the assumption that the non-volatile material consists of carbonaceous compounds. The average diurnal cycles of the BC emissions from road traffic (as inferred from the ratio of the incremental concentrations of nitrogen oxides (NOx and BC measured on a densely trafficked street and the fluxes of non-volatile material at tower level are in close agreement, suggesting a traffic source of BC. We have estimated the emission factors (EFs for non-volatile particles Dp to be 2.4 ± 1.4 mg veh−1 km−1 based on either CO2 fluxes or traffic activity data. Light (LDV and heavy duty vehicle (HDV EFs were estimated using multiple linear regression and reveal that for non

  4. Submicron Y2O3 particles codoped with Eu and Tb ions: size controlled synthesis and tuning the luminescence emission.

    Science.gov (United States)

    Atabaev, Timur Sh; Kim, Hyung-Kook; Hwang, Yoon-Hwae

    2012-05-01

    Eu(3+) and Tb(3+) codoped Y(2)O(3) submicron particles were prepared using the simple urea homogeneous precipitation method. X-ray diffraction patterns revealed the synthesized particles to have a pure cubic Y(2)O(3) structure. Field-emission scanning electron microscopy and field-emission transmission electron microscopy showed that the synthesized particles had almost uniform spherical shapes. The luminescence color emission of the synthesized particles could be tuned from red due to the effective (5)D(0)→(7)F(j) (j=0, 1, 2 and 3) transitions within Eu(3+) to green due to the (5)D(4)→(7)F(5) transition within Tb(3+) by switching the excitation wavelength from 255 to 310 nm. Luminescence quenching was observed at high dopant concentrations. Strong and effective color-tunable emission is expected to find a wide range of applications in industry. Copyright © 2011 Elsevier Inc. All rights reserved.

  5. Beschrijving van een verdampings-condensatie aerosol generator voor de produktie van submicron aerosol

    NARCIS (Netherlands)

    Feijt; A.*; Meulen; A.van der

    1985-01-01

    Dit rapport is een handleiding voor een bedrijfszeker, routinematig gebruik van een zgn. Evaporation-Condensation aerosol Conditioner. Met deze aerosol generatie apparatuur kunnen op stabiele, reproduceerbare manier zeer hoge concentraties (tot 1 miljoen deeltjes per cc) monodispers submicron

  6. Cathepsin K-targeted sub-micron particles for regenerative repair of vascular elastic matrix.

    Science.gov (United States)

    Jennewine, Brenton; Fox, Jonathan; Ramamurthi, Anand

    2017-04-01

    Abdominal Aortic Aneurysms (AAA) involve slow dilation and weakening of the aortic wall due to breakdown of structural matrix components, such as elastic fibers by chronically overexpressed matrix metalloproteinases (MMPs), primarily, MMPs-2 and -9. Auto-regenerative repair of disrupted elastic fibers by smooth muscle cells (SMCs) at the AAA site is intrinsically poor and together with chronic proteolysis prevents restoration of elastin homeostasis, necessary to enable AAA growth arrest or regression to a healthy state. Oral doxycycline (DOX) therapy can inhibit MMPs to slow AAA growth, but has systemwide side-effects and inhibits new elastin deposition within AAA tissue, diminishing prospects for restoring elastin homeostasis preventing the arrest/regression of AAA growth. We have thus developed cationic amphiphile (DMAB)-modified submicron particles (SMPs) that uniquely exhibit pro-elastogenic and anti-proteolytic properties, separate from similar effects of the encapsulated drug. These SMPs can enable sustained, low dose DOX delivery within AAA tissue to augment elastin regenerative repair. To provide greater specificity of SMP targeting, we have conjugated the DOX-SMP surface with an antibody against cathepsin K, a lysosomal protease that is highly overexpressed within AAA tissue. We have determined conditions for efficient cathepsin K Ab conjugation onto the SMPs, improved SMP binding to aneurysmal SMCs in culture and to injured vessel walls ex vivo, conjugation did not affect DOX release from the SMPs, and improved pro-elastogenic and anti-proteolytic effects due to the SMPs likely due to their increased proximity to cells via binding. Our study results suggest that cathepsin K Ab conjugation is a useful targeting modality for our pro-regenerative SMPs. Future studies will investigate SMP retention and biodistribution following targeting to induced AAAs in rat models through intravenous or catheter-based aortal infusion and thereafter their efficacy for

  7. Effects of submicron ammonium sulfate particles on the growth and yield of komatsuna (Brassica rapa L. var. perviridis)

    Science.gov (United States)

    Motai, Akira; Nakaba, Satoshi; Lenggoro, I. Wuled; Watanabe, Makoto; Wada, Yoshiharu; Izuta, Takeshi

    2017-11-01

    The aim of this study was to determine the effects of submicron ammonium sulfate (AS) particles on komatsuna (Brassica rapa L. cv. Hakkei) plants. First, we optimized a leaf-washing method to measure the amount of AS particles deposited on the leaf surface of the plants. Then, we used this method to determine the retention time of particles deposited on the leaf surface of the plants. We also investigated the effects of AS particles on the growth and yield of the plants. Almost all the AS particles deposited on the leaf surface were removed within 1 min washing time with ultrapure water, and ion leaching from the leaf was relatively slow but continuous during the leaf-washing procedure. On the basis of these results, we determined that 1 min was a suitable washing time to remove most of the AS particles while minimizing the influence of ion leaching from the leaf. The amount of particulate SO42- deposited on the leaf surface decreased over time, probably because AS particles deposited on the leaf surface deliquesced, allowing ions such as SO42- in the deliquescence solution to be absorbed into the leaf. The plants were grown and exposed to AS particles for 16 days in naturally lit phytotrons. The daily mean increase in the concentration of SO42- in PM2.5 by the exposure to AS particles was 22.5 μg m-3 in the phytotrons. The growth and yield of the plants were significantly reduced by the exposure to AS particles. The exposure to AS particles did not affect the leaf concentrations of nitrogen and chlorophyll, but significantly reduced stomatal conductance. Therefore, stomatal closure is one of the reasons for the AS particle-induced reductions in the growth and yield of komatsuna plants.

  8. Transglutaminase-induced or citric acid-mediated cross-linking of whey proteins to tune the characteristics of subsequently desolvated sub-micron and nano-scaled particles.

    Science.gov (United States)

    Bagheri, Leila; Yarmand, Mohammadsaeed; Madadlou, Ashkan; Mousavi, Mohammad E

    2014-01-01

    Whey proteins were inter-connected either by the enzyme transglutaminase or citric acid and then desolvated with ethanol to generate particles. Both samples comprised of sub-micron (>300 nm) and nano-scaled (~100 nm) particles based on the hydrodynamic size measurements. Enzyme-induced cross-linking of proteins yielded more monodisperse particles and decreased the mean size of the major (nano-scaled) fraction of particles. Scanning electron microscopy images revealed a spherical morphology for all samples with mean sizes of particles from enzymatically cross-linked proteins. The mediating role of citric acid in bridging the proteins was confirmed by Fourier transform infrared spectroscopy. Differential scanning calorimetry indicated that pre-heating of protein solution before cross-linking and desolvation denatured the proteins entirely. In vitro degradation of whey protein particles in a simulated gastric fluid demonstrated that cross-linking of whey proteins before desolvation stage enhanced significantly the digestion stability of particles.

  9. Aerosols in the tropical and subtropical UT/LS: in-situ measurements of submicron particle abundance and volatility

    Directory of Open Access Journals (Sweden)

    S. Borrmann

    2010-06-01

    Full Text Available Processes occurring in the tropical upper troposphere (UT, the Tropical Transition Layer (TTL, and the lower stratosphere (LS are of importance for the global climate, for stratospheric dynamics and air chemistry, and for their influence on the global distribution of water vapour, trace gases and aerosols. In this contribution we present aerosol and trace gas (in-situ measurements from the tropical UT/LS over Southern Brazil, Northern Australia, and West Africa. The instruments were operated on board of the Russian high altitude research aircraft M-55 "Geophysica" and the DLR Falcon-20 during the campaigns TROCCINOX (Araçatuba, Brazil, February 2005, SCOUT-O3 (Darwin, Australia, December 2005, and SCOUT-AMMA (Ouagadougou, Burkina Faso, August 2006. The data cover submicron particle number densities and volatility from the COndensation PArticle counting System (COPAS, as well as relevant trace gases like N2O, ozone, and CO. We use these trace gas measurements to place the aerosol data into a broader atmospheric context. Also a juxtaposition of the submicron particle data with previous measurements over Costa Rica and other tropical locations between 1999 and 2007 (NASA DC-8 and NASA WB-57F is provided. The submicron particle number densities, as a function of altitude, were found to be remarkably constant in the tropical UT/LS altitude band for the two decades after 1987. Thus, a parameterisation suitable for models can be extracted from these measurements. Compared to the average levels in the period between 1987 and 2007 a slight increase of particle abundances was found for 2005/2006 at altitudes with potential temperatures, Θ, above 430 K. The origins of this increase are unknown except for increases measured during SCOUT-AMMA. Here the eruption of the Soufrière Hills volcano in the Caribbean caused elevated particle mixing ratios. The vertical profiles from Northern hemispheric mid-latitudes between 1999 and 2006 also are

  10. In Situ Solid Particle Generator

    Science.gov (United States)

    Agui, Juan H.; Vijayakumar, R.

    2013-01-01

    Particle seeding is a key diagnostic component of filter testing and flow imaging techniques. Typical particle generators rely on pressurized air or gas sources to propel the particles into the flow field. Other techniques involve liquid droplet atomizers. These conventional techniques have drawbacks that include challenging access to the flow field, flow and pressure disturbances to the investigated flow, and they are prohibitive in high-temperature, non-standard, extreme, and closed-system flow conditions and environments. In this concept, the particles are supplied directly within a flow environment. A particle sample cartridge containing the particles is positioned somewhere inside the flow field. The particles are ejected into the flow by mechanical brush/wiper feeding and sieving that takes place within the cartridge chamber. Some aspects of this concept are based on established material handling techniques, but they have not been used previously in the current configuration, in combination with flow seeding concepts, and in the current operational mode. Unlike other particle generation methods, this concept has control over the particle size range ejected, breaks up agglomerates, and is gravity-independent. This makes this device useful for testing in microgravity environments.

  11. A novel method to detect unlabeled inorganic nanoparticles and submicron particles in tissue by sedimentation field-flow fractionation

    Science.gov (United States)

    Deering, Cassandra E; Tadjiki, Soheyl; Assemi, Shoeleh; Miller, Jan D; Yost, Garold S; Veranth, John M

    2008-01-01

    A novel methodology to detect unlabeled inorganic nanoparticles was experimentally demonstrated using a mixture of nano-sized (70 nm) and submicron (250 nm) silicon dioxide particles added to mammalian tissue. The size and concentration of environmentally relevant inorganic particles in a tissue sample can be determined by a procedure consisting of matrix digestion, particle recovery by centrifugation, size separation by sedimentation field-flow fractionation (SdFFF), and detection by light scattering. Background Laboratory nanoparticles that have been labeled by fluorescence, radioactivity, or rare elements have provided important information regarding nanoparticle uptake and translocation, but most nanomaterials that are commercially produced for industrial and consumer applications do not contain a specific label. Methods Both nitric acid digestion and enzyme digestion were tested with liver and lung tissue as well as with cultured cells. Tissue processing with a mixture of protease enzymes is preferred because it is applicable to a wide range of particle compositions. Samples were visualized via fluorescence microscopy and transmission electron microscopy to validate the SdFFF results. We describe in detail the tissue preparation procedures and discuss method sensitivity compared to reported levels of nanoparticles in vivo. Conclusion Tissue digestion and SdFFF complement existing techniques by precisely identifying unlabeled metal oxide nanoparticles and unambiguously distinguishing nanoparticles (diameter<100 nm) from both soluble compounds and from larger particles of the same nominal elemental composition. This is an exciting capability that can facilitate epidemiological and toxicological research on natural and manufactured nanomaterials. PMID:19055780

  12. Application of I-structure though-glass interconnect filled with submicron gold particles to a hermetic sealing device

    Science.gov (United States)

    Nomura, Kazuya; Okada, Akiko; Shoji, Shuichi; Ogashiwa, Toshinori; Mizuno, Jun

    2016-10-01

    We propose hermetic sealing of a glass-to-glass structure with an I-structure through-glass interconnect via (TGV) filled with submicron Au particles. The top and bottom bumps and the TGV were formed by a simple filling process with a bump-patterned dry film resist. The sealing devices consisting of two glass substrates were bonded via Au interlayers. Vacuum ultraviolet irradiation in the presence of oxygen gas (VUV/O3) pretreatment was used for low-temperature Au-Au bonding at 200 °C. The bonded samples showed He leakage rates of less than 1.3  ×  10-9 Pa m3 s-1. The cross-sectional scanning electron microscope images of the fabricated I-structure TGV showed perfect adhesion between the I-structure TGV and glass substrate. These results indicate that the proposed I-structure TGV is suitable for hermetic sealing devices.

  13. A novel method to detect unlabeled inorganic nanoparticles and submicron particles in tissue by sedimentation field-flow fractionation

    Directory of Open Access Journals (Sweden)

    Yost Garold S

    2008-12-01

    Full Text Available Abstract A novel methodology to detect unlabeled inorganic nanoparticles was experimentally demonstrated using a mixture of nano-sized (70 nm and submicron (250 nm silicon dioxide particles added to mammalian tissue. The size and concentration of environmentally relevant inorganic particles in a tissue sample can be determined by a procedure consisting of matrix digestion, particle recovery by centrifugation, size separation by sedimentation field-flow fractionation (SdFFF, and detection by light scattering. Background Laboratory nanoparticles that have been labeled by fluorescence, radioactivity, or rare elements have provided important information regarding nanoparticle uptake and translocation, but most nanomaterials that are commercially produced for industrial and consumer applications do not contain a specific label. Methods Both nitric acid digestion and enzyme digestion were tested with liver and lung tissue as well as with cultured cells. Tissue processing with a mixture of protease enzymes is preferred because it is applicable to a wide range of particle compositions. Samples were visualized via fluorescence microscopy and transmission electron microscopy to validate the SdFFF results. We describe in detail the tissue preparation procedures and discuss method sensitivity compared to reported levels of nanoparticles in vivo. Conclusion Tissue digestion and SdFFF complement existing techniques by precisely identifying unlabeled metal oxide nanoparticles and unambiguously distinguishing nanoparticles (diameter

  14. Enhanced computational performance of the lattice Boltzmann model for simulating micron- and submicron-size particle flows and non-Newtonian fluid flows

    Science.gov (United States)

    Başağaoğlu, Hakan; Harwell, John R.; Nguyen, Hoa; Succi, Sauro

    2017-04-01

    Significant improvements in the computational performance of the lattice-Boltzmann (LB) model, coded in FORTRAN90, were achieved through application of enhancement techniques. Applied techniques include optimization of array memory layouts, data structure simplification, random number generation outside the simulation thread(s), code parallelization via OpenMP, and intra- and inter-timestep task pipelining. Effectiveness of these optimization techniques was measured on three benchmark problems: (i) transient flow of multiple particles in a Newtonian fluid in a heterogeneous fractured porous domain, (ii) thermal fluctuation of the fluid at the sub-micron scale and the resultant Brownian motion of a particle, and (iii) non-Newtonian fluid flow in a smooth-walled channel. Application of the aforementioned optimization techniques resulted in an average 21 × performance improvement, which could significantly enhance practical uses of the LB models in diverse applications, focusing on the fate and transport of nano-size or micron-size particles in non-Newtonian fluids.

  15. Deformation Behavior of Sub-micron and Micron Sized Alumina Particles in Compression.

    Energy Technology Data Exchange (ETDEWEB)

    Sarobol, Pylin; Chandross, Michael E.; Carroll, Jay; Mook, William; Boyce, Brad; Kotula, Paul Gabriel; McKenzie, Bonnie Beth; Bufford, Daniel Charles; Hall, Aaron Christopher.

    2014-09-01

    The ability to integrate ceramics with other materials has been limited due to high temperature (>800degC) ceramic processing. Recently, researchers demonstrated a novel process , aerosol deposition (AD), to fabricate ceramic films at room temperature (RT). In this process, sub - micro n sized ceramic particles are accelerated by pressurized gas, impacted on the substrate, plastically deformed, and form a dense film under vacuum. This AD process eliminates high temperature processing thereby enabling new coatings and device integration, in which ceramics can be deposited on metals, plastics, and glass. However, k nowledge in fundamental mechanisms for ceramic particle s to deform and form a dense ceramic film is still needed and is essential in advancing this novel RT technology. In this wo rk, a combination of experimentation and atomistic simulation was used to determine the deformation behavior of sub - micron sized ceramic particle s ; this is the first fundamental step needed to explain coating formation in the AD process . High purity, singl e crystal, alpha alumina particles with nominal size s of 0.3 um and 3.0 um were examined. Particle characterization, using transmission electron microscopy (TEM ), showed that the 0.3 u m particles were relatively defect - free single crystals whereas 3.0 u m p articles were highly defective single crystals or particles contained low angle grain boundaries. Sub - micron sized Al 2 O 3 particles exhibited ductile failure in compression. In situ compression experiments showed 0.3um particles deformed plastically, fractured, and became polycrystalline. Moreover, dislocation activit y was observed within the se particles during compression . These sub - micron sized Al 2 O 3 particles exhibited large accum ulated strain (2 - 3 times those of micron - sized particles) before first fracture. I n agreement with the findings from experimentation , a tomistic simulation s of nano - Al 2 O 3 particles showed dislocation slip and

  16. Ozone reaction with clothing and its initiated particle generation in an environmental chamber

    Science.gov (United States)

    Rai, Aakash C.; Guo, Bing; Lin, Chao-Hsin; Zhang, Jianshun; Pei, Jingjing; Chen, Qingyan

    2013-10-01

    Ozone-initiated chemistry in indoor air can produce sub-micron particles, which are potentially harmful for human health. Occupants in indoor spaces constitute potential sites for particle generation through ozone reactions with human skin and clothing. This investigation conducted chamber experiments to examine particle generation from ozone reactions with clothing (a T-shirt) under different indoor conditions. We studied the effect of various factors such as ozone concentration, relative humidity, soiling levels of T-shirt with human skin oils, and air change rate on particle generation. The results showed that ozone reactions with the T-shirt generated sub-micron particles, which were enhanced by the soiling of the T-shirt with human skin oils. In these reactions, a burst of ultrafine particles was observed about one hour after ozone injection, and then the particles grew to larger sizes. The particle generation from the ozone reactions with the soiled T-shirt was significantly affected by the different factors studied and these reactions were identified as another potential source for indoor ultrafine particles.

  17. [Submicron particles in smoke resulting from welding alloys and cast alloy in metalworking industry].

    Science.gov (United States)

    Avino, P; Manigrasso, M; Fanizza, Carla; Carrai, P; Solfanelli, Linda

    2013-01-01

    The toxicity of welding fumes depends on both chemical composition and ability to penetrate and deposit deeply in the lungs. Their penetration and deposition in the regions of the respiratory system is mainly determined by their size. The knowledge of the size distribution of welding fumes is a crucial information towards the estimate of the doses of toxic compounds delivered into the respiratory tract. Particle number size distribution was continuously measured during different welding operations by means of a Fast Mobility Particle Sizer, which counts and classifies particles, according to their electrical mobility, in 32 size-channels, in the range from 5.6 to 523 nm, with is time resolution. The temporal evolution of submicrometric particles (6-523 nm), nucleation mode particles (6-16 nm) and the fraction 19-523 nm before, during and after the welding operations performed with/without local exhaust ventilation are reported and extensively discussed. Before welding, nucleation mode particles represent about 7% of submicrometric particles; after about 40 s from the welding start, the percent contribution of nucleation mode particles increases to 60%. Total and nucleation mode particle concentrations increase from 2.1 x 10(4) to 2.0 x 10(6) and from 1.6 x 10(3) to 1.0 x 10(6), respectively. The temporal variation of the particle number size distribution across the peaks, evidences the strong and fast-evolving contribution of nucleation mode particles: peak values are maintained for less than 10 s. The implication of such contribution on human health is linked to high deposition efficiency of the submicrometric particles in the alveolar interstitial region of the human respiratory system, where gas exchange occurs.

  18. Cold Spray Coating of Submicronic Ceramic Particles on Poly(vinyl alcohol) in Dry and Hydrogel States

    Science.gov (United States)

    Moreau, David; Borit, François; Corté, Laurent; Guipont, Vincent

    2017-06-01

    We report an approach using cold spray technology to coat poly(vinyl alcohol) (PVA) in polymer and hydrogel states with hydroxyapatite (HA). Using porous aggregated HA powder, we hypothesized that fragmentation of the powder upon cold spray could lead to formation of a ceramic coating on the surface of the PVA substrate. However, direct spraying of this powder led to complete destruction of the swollen PVA hydrogel substrate. As an alternative, HA coatings were successfully produced by spraying onto dry PVA substrates prior to swelling in water. Dense homogeneous HA coatings composed of submicron particles were obtained using rather low-energy spraying parameters (temperature 200-250 °C, pressure 1-3 MPa). Coated PVA substrates could swell in water without removal of the ceramic layer to form HA-coated hydrogels. Microscopic observations and in situ measurements were used to explain how local heating and impact of sprayed aggregates induced surface roughening and strong binding of HA particles to the molten PVA substrate. Such an approach could lead to design of ceramic coatings whose roughness and crystallinity can be finely adjusted to improve interfacing with biological tissues.

  19. THE INFLUENCE OF CARBON BURNOUT ON SUBMICRON PARTICLE FORMATION FROM EMULSIFIED FUEL OIL COMBUSTION

    Science.gov (United States)

    The paper gives results of an examination of particle behavior and particle size distributions from the combustion of different fuel oils and emulsified fuels in three experimental combusators. Results indicate that improved carbon (C) burnout from fule oil combustion, either by...

  20. Ozone and limonene in indoor air: a source of submicron particle exposure.

    Science.gov (United States)

    Wainman, T; Zhang, J; Weschler, C J; Lioy, P J

    2000-01-01

    Little information currently exists regarding the occurrence of secondary organic aerosol formation in indoor air. Smog chamber studies have demonstrated that high aerosol yields result from the reaction of ozone with terpenes, both of which commonly occur in indoor air. However, smog chambers are typically static systems, whereas indoor environments are dynamic. We conducted a series of experiments to investigate the potential for secondary aerosol in indoor air as a result of the reaction of ozone with d-limonene, a compound commonly used in air fresheners. A dynamic chamber design was used in which a smaller chamber was nested inside a larger one, with air exchange occurring between the two. The inner chamber was used to represent a model indoor environment and was operated at an air exchange rate below 1 exchange/hr, while the outer chamber was operated at a high air exchange rate of approximately 45 exchanges/hr. Limonene was introduced into the inner chamber either by the evaporation of reagent-grade d-limonene or by inserting a lemon-scented, solid air freshener. A series of ozone injections were made into the inner chamber during the course of each experiment, and an optical particle counter was used to measure the particle concentration. Measurable particle formation and growth occurred almost exclusively in the 0.1-0.2 microm and 0.2-0.3 microm size fractions in all of the experiments. Particle formation in the 0.1-0.2 microm size range occurred as soon as ozone was introduced, but the formation of particles in the 0.2-0.3 microm size range did not occur until at least the second ozone injection occurred. The results of this study show a clear potential for significant particle concentrations to be produced in indoor environments as a result of secondary particle formation via the ozone-limonene reaction. Because people spend the majority of their time indoors, secondary particles formed in indoor environments may make a significant contribution to

  1. Submicron polyacrolein particles in situ embedded with upconversion nanoparticles for bioassay

    Science.gov (United States)

    Generalova, A. N.; Kochneva, I. K.; Khaydukov, E. V.; Semchishen, V. A.; Guller, A. E.; Nechaev, A. V.; Shekhter, A. B.; Zubov, V. P.; Zvyagin, A. V.; Deyev, S. M.

    2015-01-01

    We report a new surface modification approach of upconversion nanoparticles (UCNPs) structured as inorganic hosts NaYF4 codoped with Yb3+ and Er3+ based on their encapsulation in a two-stage process of precipitation polymerization of acrolein under alkaline conditions in the presence of UCNPs. The use of tetramethylammonium hydroxide both as an initiator of acrolein polymerization and as an agent for UCNP hydrophilization made it possible to increase the polyacrolein yield up to 90%. This approach enabled the facile, lossless embedment of UCNPs into the polymer particles suitable for bioassay. These particles are readily dispersible in aqueous and physiological buffers, exhibiting excellent photoluminescence properties, chemical stability, and also allow the control of particle diameters. The feasibility of the as-produced photoluminescent polymer particles mean-sized 260 nm for in vivo optical whole-animal imaging was also demonstrated using a home-built epi-luminescence imaging system.We report a new surface modification approach of upconversion nanoparticles (UCNPs) structured as inorganic hosts NaYF4 codoped with Yb3+ and Er3+ based on their encapsulation in a two-stage process of precipitation polymerization of acrolein under alkaline conditions in the presence of UCNPs. The use of tetramethylammonium hydroxide both as an initiator of acrolein polymerization and as an agent for UCNP hydrophilization made it possible to increase the polyacrolein yield up to 90%. This approach enabled the facile, lossless embedment of UCNPs into the polymer particles suitable for bioassay. These particles are readily dispersible in aqueous and physiological buffers, exhibiting excellent photoluminescence properties, chemical stability, and also allow the control of particle diameters. The feasibility of the as-produced photoluminescent polymer particles mean-sized 260 nm for in vivo optical whole-animal imaging was also demonstrated using a home-built epi-luminescence imaging

  2. Chemical characteristics of submicron particles at the central Tibetan Plateau: insights from aerosol mass spectrometry

    Directory of Open Access Journals (Sweden)

    J. Xu

    2018-01-01

    Full Text Available Recent studies have revealed a significant influx of anthropogenic aerosol from South Asia to the Himalayas and Tibetan Plateau (TP during pre-monsoon period. In order to characterize the chemical composition, sources, and transport processes of aerosol in this area, we carried out a field study during June 2015 by deploying a suite of online instruments including an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-AMS and a multi-angle absorption photometer (MAAP at Nam Co station (90°57′ E, 30°46′ N; 4730 m a.s.l. at the central of the TP. The measurements were made at a period when the transition from pre-monsoon to monsoon occurred. The average ambient mass concentration of submicron particulate matter (PM1 over the whole campaign was  ∼  2.0 µg m−3, with organics accounting for 68 %, followed by sulfate (15 %, black carbon (8 %, ammonium (7 %, and nitrate (2 %. Relatively higher aerosol mass concentration episodes were observed during the pre-monsoon period, whereas persistently low aerosol concentrations were observed during the monsoon period. However, the chemical composition of aerosol during the higher aerosol concentration episodes in the pre-monsoon season was on a case-by-case basis, depending on the prevailing meteorological conditions and air mass transport routes. Most of the chemical species exhibited significant diurnal variations with higher values occurring during afternoon and lower values during early morning, whereas nitrate peaked during early morning in association with higher relative humidity and lower air temperature. Organic aerosol (OA, with an oxygen-to-carbon ratio (O ∕ C of 0.94, was more oxidized during the pre-monsoon period than during monsoon (average O ∕ C ratio of 0.72, and an average O ∕ C was 0.88 over the entire campaign period, suggesting overall highly oxygenated aerosol in the central TP. Positive matrix factorization of the

  3. Preparation of chitosan-TPP sub-micron particles: Critical evaluation and derived recommendations.

    Science.gov (United States)

    Rázga, Filip; Vnuková, Dominika; Némethová, Veronika; Mazancová, Petra; Lacík, Igor

    2016-10-20

    The controlled preparation of chitosan particles is far from being trivial due to a considerable number of experimental parameters. For chitosan-tripolyphosphate (TPP) particles we evaluate the impact of chemical (type of chitosan, concentration, chitosan to TPP ratio, pH, ionic strength) and process factors (dialysis, stirring rate, rate of TPP addition, temperature, needle diameter) on the size and colloidal stability. The particles were prepared at pH=6.0 at which chitosan adopts the coiled conformation that is discussed as the dominant factor in controlling the stoichiometry of crosslinking reaction shifted towards TPP. These conditions result in identical particle size around 400nm and zeta potential around 22mV. The colloidal stability evaluated 24 hours after preparation depends on the amount of TPP during crosslinking. Under the same conditions, the colloidal stability up to 1 month is demonstrated. Several recommendations are provided to increase the control over formation of chitosan-TPP particles. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Oxygenated organic functional groups and their sources in single and submicron organic particles in MILAGRO 2006 campaign

    Directory of Open Access Journals (Sweden)

    S. Liu

    2009-09-01

    Full Text Available Fourier Transform Infrared (FTIR and X-ray Fluorescence (XRF were used to measure organic functional groups and elements of submicron particles collected during MILAGRO in March 2006 on three platforms: the Mexico City urban area (SIMAT, the high altitude site at 4010 m (Altzomoni, and the NCAR C130 aircraft. Scanning Transmission X-ray Microscopy (STXM and Near-Edge X-ray Absorption Fine Structure (NEXAFS were applied to single particle organic functional group abundance analysis of particles simultaneously collected at SIMAT and C130. Correlations of elemental concentrations showed different groups of source-related elements at SIMAT, Altzomoni, and C130, suggesting different processes affecting the air masses sampled at the three platforms. Cluster analysis resulted in seven distinct clusters of FTIR spectra, with the last three clusters consisting of spectra collected almost exclusively on the C130 platform, reflecting the variety of sources contributing to C130 samples. Positive Matrix Factorization (PMF of STXM-NEXAFS spectra identified three main factors representing soot, secondary, and biomass burning type spectra. PMF of FTIR spectra resulted in two fossil fuel combustion factors and one biomass burning factor, the former representative of source regions to the northeast and southwest of SIMAT. Alkane, carboxylic acid, amine, and alcohol functional groups were mainly associated with combustion related sources, while non-acid carbonyl groups were likely from biomass burning events. The majority of OM and O/C was attributed to combustion sources, although no distinction between direct emissions and atmospherically processed OM could be identified.

  5. Photothermal heating enabled by plasmonic nanoantennas for electrokinetic manipulation and sorting of submicron particles

    DEFF Research Database (Denmark)

    Ndukaife, Justus C.; Mishra, Avanish; Guler, Urcan

    2014-01-01

    The photo-induced collective heating enabled by a plasmonic nanoantenna array is for the first time harnessed for rapid concentration, manipulation and sorting of particles, with high throughput. This work could find application in biosensing, and surface enhanced spectroscopies © 2014 OSA....

  6. Ni-functionalized submicron mesoporous silica particles as a sorbent for metal affinity chromatography.

    Science.gov (United States)

    Kurdyukov, Dmitry A; Chernova, Ekaterina N; Russkikh, Yana V; Eurov, Daniil A; Sokolov, Vasily V; Bykova, Anna A; Shilovskikh, Vladimir V; Keltsieva, Olga A; Ubyivovk, Eugenii V; Anufrikov, Yuri A; Fedorova, Anna V; Selyutin, Artem A; Sukhodolov, Nicolay G; Podolskaya, Ekaterina P; Golubev, Valery G

    2017-09-01

    In this research, a novel IMAC sorbent with high specificity for chlorine-containing compounds was developed. Ni-functionalized monodisperse spherical mesoporous silica particles of 500±25nm diameter were synthesized and their metal affinity properties were studied with the use of diclofenac as the model substance. The particles were aggregatively stable in the pH range of 3-12. The sorbent demonstrated a high adsorption capacity (0.60±0.06μg of DCF per 1mg of the sorbent) and high adsorption/desorption rate (20 and 5min was enough for the sorbent saturation and desorption of DCF, correspondingly). A mixture of eluents with addition of PFOS providing the almost complete recovery (98%) of diclofenac was first proposed. The monodispersity and the high sedimentation and aggregative stability of the particles provide the formation of a stable hydrosol even under ultrasound treatment which makes the mSiO2/Ni particles suitable for batch chromatography. Copyright © 2017 Elsevier B.V. All rights reserved.

  7. Bragg diffraction from sub-micron particles isolated by optical tweezers

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Yuan, E-mail: ygao0709@anl.gov; Harder, Ross; Southworth, Stephen; Guest, Jeffrey; Ocola, Leonidas; Young, Linda [Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439 (United States); Scherer, Norbert; Yan, Zijie [Department of Chemistry, University of Chicago, Chicago, IL 60637 (United States); Pelton, Matthew [Department of Physics, University of Maryland, Baltimore County, MD 21250 (United States)

    2016-07-27

    We describe an apparatus using dynamic holographic optical tweezers which is capable of trapping and aligning a single micron scale anisotropic ZnO particle for x-ray Bragg diffraction experiments. The optical tweezers demonstrate enough stability to perform coherent x-ray diffraction imaging.

  8. Annual trends in occurrence of submicron particles in ambient air and health risk posed by particle bound metals.

    Science.gov (United States)

    Izhar, Saifi; Goel, Anubha; Chakraborty, Abhishek; Gupta, Tarun

    2016-03-01

    Risk analysis is highly important in toxicology and public health studies. Health risk related to exposure to toxic metals of PM1 was assessed. Concentrations of 13 heavy metals, adsorbed to submicron particulate matter PM1 were experimentally examined but only 12 metals were found at detectable levels inside IIT Kanpur campus in 2008-2009 for all months excluding June and October. A total of 90 samples collected for 8 h sampling time by a single stage round nozzle, grease impaction substrate based impactor type PM1 sampler were analysed by ICP-OES (Inductively Coupled Plasma Optical Emission Spectrometry). Results showed daily average PM1 concentration is 102.46 ± 35.9 μg/m(3) and metal concentration followed the trend: Ca > Fe > Mg > Zn > Pb > Cu > Cr > Ni > Se > Cd > V > As. Contamination level assessment using geo-accumulation index showed Ca, Fe and Mg exhibited non contamination whereas metals like Cr, Zn, As, Cd, Pb, Se, Ni and Cu exhibited ranges from moderate to extreme contamination. Ingestion is found to be the major exposure pathway for heavy metals. Non-carcinogenic health risk assessment for Pb, Cd and Cr (HI > 1) signified strong chances of adverse impact on children whereas adults are well under safe limit. Cancer Risk for adults and children followed the same decreasing order, Cr(VI)>Cd > Ni > As > Pb. It was found to be higher than permissible limits (10(-6)) for adults and children both. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Noise Removal with Maintained Spatial Resolution in Raman Images of Cells Exposed to Submicron Polystyrene Particles

    Directory of Open Access Journals (Sweden)

    Linnea Ahlinder

    2016-04-01

    Full Text Available The biodistribution of 300 nm polystyrene particles in A549 lung epithelial cells has been studied with confocal Raman spectroscopy. This is a label-free method in which particles and cells can be imaged without using dyes or fluorescent labels. The main drawback with Raman imaging is the comparatively low spatial resolution, which is aggravated in heterogeneous systems such as biological samples, which in addition often require long measurement times because of their weak Raman signal. Long measurement times may however induce laser-induced damage. In this study we use a super-resolution algorithm with Tikhonov regularization, intended to improve the image quality without demanding an increased number of collected pixels. Images of cells exposed to polystyrene particles have been acquired with two different step lengths, i.e., the distance between pixels, and compared to each other and to corresponding images treated with the super-resolution algorithm. It is shown that the resolution after application of super-resolution algorithms is not significantly improved compared to the theoretical limit for optical microscopy. However, to reduce noise and artefacts in the hyperspectral Raman images while maintaining the spatial resolution, we show that it is advantageous to use short mapping step lengths and super-resolution algorithms with appropriate regularization. The proposed methodology should be generally applicable for Raman imaging of biological samples and other photo-sensitive samples.

  10. Light transport through disordered layers of dense gallium arsenide submicron particles

    Science.gov (United States)

    van der Beek, T.; Barthelemy, P.; Johnson, P. M.; Wiersma, D. S.; Lagendijk, A.

    2012-03-01

    We present a study of optical transport properties of powder layers with submicrometer, strongly scattering gallium arsenide (GaAs) particles. Uniform, thin samples with well controlled thicknesses were created through the use of varying grinding times, sedimentation fractionation, annealing, and a new sedimentation technique. These fabrication parameters were optimized to produce maximum scattering and minimum absorption. The physical properties were characterized using scanning electron microscopy (SEM) and x-ray diffraction. The optical transport mean-free path, absorption length, and the diffusion constant were determined for each sample using both continuous wave and time-resolved methods. The samples scatter strongly in the near infrared region. Total reflection and transmission measurements show that all of these samples have high absorption. X-ray diffraction results suggest that the source of this absorption is grinding induced strain and/or defects in the crystal structure. For all the different grinded GaAs powder samples that we investigated, the absorption length was less than ten micrometers.

  11. The Effect of Submicron Second-Phase Particles on the Rate of Grain Refinement in a Copper-Oxygen Alloy During Cold Spray

    Science.gov (United States)

    Zhang, Yinyin; Brodusch, Nicolas; Descartes, Sylvie; Shockley, J. Michael; Gauvin, Raynald; Chromik, Richard R.

    2017-10-01

    The effect of non-deformable submicron second-phase particles ( d = 200-500 nm) on microstructural refinement during cold spray was examined. Using single particle impact testing, two types of splats were fabricated using two different feedstocks: a Cu-0.21wt.%O powder containing Cu2O second-phase particles and a single-phase Cu. Microstructural evolution analysis using high-resolution electron backscatter diffraction shows grain refinement occurred at a higher rate in the Cu-0.21wt.%O powder. That was due to dynamic recrystallization initiated by particle-stimulated nucleation (PSN). High-strain-rate deformation of cold spray was found to be the key to activate PSN. The present study suggests cold spray is a possible technique to fabricate ultrafine-grained materials by using feedstock containing second-phase particles.

  12. Characterization of size, morphology and elemental composition of nano-, submicron, and micron particles of street dust separated using field-flow fractionation in a rotating coiled column.

    Science.gov (United States)

    Fedotov, Petr S; Ermolin, Mikhail S; Karandashev, Vasily K; Ladonin, Dmitry V

    2014-12-01

    For the first time, nano- and submicron particles of street dust have been separated, weighted, and analyzed. A novel technique, sedimentation field-flow fractionation in a rotating coiled column, was applied to the fractionation of dust samples with water being used as a carrier fluid. The size and morphology of particles in the separated fractions were characterized by electronic microscopy before digestion and the determination of the concentration of elements by ICP-AES and ICP-MS. The elements that may be of anthropogenic origin (Zn, Cr, Ni, Cu, Cd, Sn, Pb) were found to concentrate mainly in particles present only about 0.1 mass% of the sample they are of special concern due to their increased mobility and ability to penetrate into the deepest alveolar area of the lungs. For rare earth elements (La, Ce, Pr, Nd, Sm) that are evidently of natural source and may be found in soil minerals, in contrary, higher concentrations were observed in large particles (10-100 μm). Sc was an exception that needs further studies. The proposed approach to the fractionation and analysis of nano-, submicron, and micron particles can be a powerful tool for risk assessment related to toxic elements in dust, ash, and other particulate environmental samples. Copyright © 2014 Elsevier B.V. All rights reserved.

  13. Toward Quantifying the Mass-Based Hygroscopicity of Individual Submicron Atmospheric Aerosol Particles with STXM/NEXAFS and SEM/EDX

    Science.gov (United States)

    Yancey Piens, D.; Kelly, S. T.; OBrien, R. E.; Wang, B.; Petters, M. D.; Laskin, A.; Gilles, M. K.

    2014-12-01

    The hygroscopic behavior of atmospheric aerosols influences their optical and cloud-nucleation properties, and therefore affects climate. Although changes in particle size as a function of relative humidity have often been used to quantify the hygroscopic behavior of submicron aerosol particles, it has been noted that calculations of hygroscopicity based on size contain error due to particle porosity, non-ideal volume additivity and changes in surface tension. We will present a method to quantify the hygroscopic behavior of submicron aerosol particles based on changes in mass, rather than size, as a function of relative humidity. This method results from a novel experimental approach combining scanning transmission x-ray microscopy with near-edge x-ray absorption fine spectroscopy (STXM/NEXAFS), as well as scanning electron microscopy with energy dispersive x-ray spectroscopy (SEM/EDX) on the same individual particles. First, using STXM/NEXAFS, our methods are applied to aerosol particles of known composition ‒ for instance ammonium sulfate, sodium bromide and levoglucosan ‒ and validated by theory. Then, using STXM/NEXAFS and SEM/EDX, these methods are extended to mixed atmospheric aerosol particles collected in the field at the DOE Atmospheric Radiation Measurement (ARM) Climate Research Facility at the Southern Great Planes sampling site in Oklahoma, USA. We have observed and quantified a range of hygroscopic behaviors which are correlated to the composition and morphology of individual aerosol particles. These methods will have implications for parameterizing aerosol mixing state and cloud-nucleation activity in atmospheric models.

  14. Simulations of flame generated particles

    KAUST Repository

    Patterson, Robert

    2016-01-05

    The nonlinear structure of the equations describing the evolution of a population of coagulating particles in a flame make the use of stochastic particle methods attractive for numerical purposes. I will present an analysis of the stochastic fluctuations inherent in these numerical methods leading to an efficient sampling technique for steady-state problems. I will also give some examples where stochastic particle methods have been used to explore the effect of uncertain parameters in soot formation models. In conclusion I will try to indicate some of the issues in optimising these methods for the study of uncertain model parameters.

  15. Dynamical effects and terahertz harmonic generation in low-doped bulk semiconductors and submicron structures

    Energy Technology Data Exchange (ETDEWEB)

    Persano Adorno, D.; Capizzo, M.C.; Zarcone, M. [Dipartimento di Fisica e Tecnologie Relative, Viale delle Scienze, Ed. 18, 90128, Palermo (Italy)

    2006-08-15

    We present results obtained using a three-dimensional multivalleys Monte Carlo (MC) model to simulate the nonlinear carrier dynamics under the influence of an intense sub-terahertz electric field in a doped bulk semiconductor. By self-consistently coupling a one-dimensional Poisson solver to the ensemble MC code we simulate also the nonlinear carrier dynamics in n{sup +}nn{sup +} structures operating under large-amplitude periodic signals and investigate the voltage-current characteristic hysteresis cycle and the high-order harmonic efficiency. For both cases we discuss the dependence of the nonlinearities and of the harmonic generation efficiency on the frequency and the intensity of the alternating signal. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  16. Source apportionment of fine PM and sub-micron particle number concentrations at a regional background site in the western Mediterranean: a 2.5 year study

    Directory of Open Access Journals (Sweden)

    M. Cusack

    2013-05-01

    Full Text Available The chemical composition and sources of ambient fine particulate matter (PM1 over a period of 2.5 years for a regional background site in the western Mediterranean are presented in this work. Furthermore, sub-micron particle number concentrations and the sources of these particles are also presented. The mean PM1 concentration for the measurement period was 8.9 μg m−3, with organic matter (OM and sulphate comprising most of the mass (3.2 and 1.5 μg m−3 respectively. Six sources were identified in PM1 by Positive Matrix Factorisation (PMF: secondary organic aerosol, secondary nitrate, industrial, traffic + biomass burning, fuel oil combustion and secondary sulphate. Typically anthropogenic sources displayed elevated concentrations during the week with reductions at weekends. Nitrate levels were elevated in winter and negligible in summer, whereas secondary sulphate levels underwent a contrasting seasonal evolution with highest concentrations in summer, similar to the fuel oil combustion source. The SOA source was influenced by episodes of sustained pollution as a result of anticyclonic conditions occurring during winter, giving rise to thermal inversions and the accumulation of pollutants in the mixing layer. Increased levels in summer were owing to higher biogenic emissions and regional recirculation of air masses. The industrial source decreased in August due to decreased emissions during the vacation period. Increases in the traffic + biomass burning source were recorded in January, April and October, which were attributed to the occurrence of the aforementioned pollution episodes and local biomass burning emission sources, which include agriculture and domestic heating systems. Average particle number concentrations (N9-825 nm from 5/11/2010 to 01/06/2011 and from 15/10/2011 to 18/12/2011 reached 3097 cm−3. Five emission sources of particle of sub-micron particles were determined by Principal Component Analysis (PCA; industrial

  17. White light generation using photonic crystal fiber with sub-micron circular lattice

    Science.gov (United States)

    Saghaei, Hamed; Ghanbari, Ashkan

    2017-08-01

    In this paper, we study a photonic crystal fiber (PCF) with circular lattice and engineer linear and nonlinear parameters by varying the diameter of air-holes. It helps us obtain low and high zero dispersion wavelengths in the visible and nearinfrared regions. We numerically demonstrate that by launching 100 fs input pulses of 1, 2, and 5 kW peak powers with center wavelength of 532 nm from an unamplified Ti:sapphire laser into a 100 mm length of the engineered PCF, supercontinua as wide as 290, 440 and 830 nm can be obtained, respectively. The spectral broadening is due to the combined action of self-phase modulation, stimulated Raman scattering and parametric four-wave-mixing generation of the pump pulses. The third and the widest spectrum covers the entire visible range and a part of near infrared region making it a suitable source for both white light applications and optical coherence tomography to measure retinal oxygen metabolic response to systemic oxygenation.

  18. The heterogeneous reaction of hydroxyl radicals with sub-micron squalane particles: a model system for understanding the oxidative aging of ambient aerosols

    Science.gov (United States)

    Smith, J. D.; Kroll, J. H.; Cappa, C. D.; Che, D. L.; Liu, C. L.; Ahmed, M.; Leone, S. R.; Worsnop, D. R.; Wilson, K. R.

    2009-05-01

    The heterogeneous reaction of OH radicals with sub-micron squalane particles, in the presence of O2, is used as a model system to explore the fundamental chemical mechanisms that control the oxidative aging of organic aerosols in the atmosphere. Detailed kinetic measurements combined with elemental mass spectrometric analysis reveal that the reaction proceeds sequentially by adding an average of one oxygenated functional group per reactive loss of squalane. The reactive uptake coefficient of OH with squalane particles is determined to be 0.3±0.07 at an average OH concentration of ~1×1010 molecules cm-3. Based on a comparison between the measured particle mass and model predictions it appears that significant volatilization of a reduced organic particle would be extremely slow in the real atmosphere. However, as the aerosols become more oxygenated, volatilization becomes a significant loss channel for organic material in the particle-phase. Together these results provide a chemical framework in which to understand how heterogeneous chemistry transforms the physiochemical properties of particle-phase organic matter in the troposphere.

  19. The heterogeneous reaction of hydroxyl radicals with sub-micron squalane particles: a model system for understanding the oxidative aging of ambient aerosols

    Directory of Open Access Journals (Sweden)

    J. D. Smith

    2009-05-01

    Full Text Available The heterogeneous reaction of OH radicals with sub-micron squalane particles, in the presence of O2, is used as a model system to explore the fundamental chemical mechanisms that control the oxidative aging of organic aerosols in the atmosphere. Detailed kinetic measurements combined with elemental mass spectrometric analysis reveal that the reaction proceeds sequentially by adding an average of one oxygenated functional group per reactive loss of squalane. The reactive uptake coefficient of OH with squalane particles is determined to be 0.3±0.07 at an average OH concentration of ~1×1010 molecules cm−3. Based on a comparison between the measured particle mass and model predictions it appears that significant volatilization of a reduced organic particle would be extremely slow in the real atmosphere. However, as the aerosols become more oxygenated, volatilization becomes a significant loss channel for organic material in the particle-phase. Together these results provide a chemical framework in which to understand how heterogeneous chemistry transforms the physiochemical properties of particle-phase organic matter in the troposphere.

  20. Submicron sized ultra-high molecular weight polyethylene wear particle analysis from revised SB Charité III total disc replacements.

    Science.gov (United States)

    Punt, Ilona; Baxter, Ryan; van Ooij, André; Willems, Paul; van Rhijn, Lodewijk; Kurtz, Steven; Steinbeck, Marla

    2011-09-01

    Submicron sized particles are frequently observed in retrieved total hip and knee periprosthetic tissues and appear to be critical in the activation of the phagocytic inflammatory response. In this paper the concentration, size and shape of ultra-high molecular weight polyethylene (UHMWPE) wear particles between 0.05 and 2.00μm were determined after isolation from periprosthetic tissues from retrieved lumbar SB Charité III total disc replacements (TDR) using scanning electron microscopy (SEM). For comparison, UHMWPE wear particles were isolated from γ-radiation-air sterilized total hip arthroplasty (THA) revision tissues. The mean concentration of UHMWPE particles in TDR tissues was 1.6×10(9)g(-1)tissue (range 1.3-2.0), which was significantly lower than the concentration of 2.3×10(9)g(-1) THA revision tissue (range 1.8-3.2) (P=0.03). The mean particle size (equivalent circular diameter: TDR, 0.46μm; THA 0.53μm, P=0.60) and mean shape were comparable between TDR and THA (aspect ratio: TDR, 1.89; THA, 1.99, P=0.35; roundness: TDR, 0.58; THA, 0.56, P=0.35). However, the TDR particles tended to be smaller and more round. Although no correlations were found between visible damage to the UHMWPE core and the concentration or shape of the UHMWPE particles, a positive correlation was found between increasing particle size and increasing rim penetration of the TDR core (P=0.04). The presence of UHMWPE particles of similar size and shape in TDR tissue, albeit lower in concentration, might explain why, unlike THA, pain rather than osteolysis is the major reason for revision surgery. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  1. Separation of submicron particles from biofuel combustion with flue gas condensation or wet condensing electrostatic precipitator. Analysis of possibilities; Avskiljning av submikrona partiklar vid biobraenslefoerbraenning med roekgaskondensering eller kondenserande vaata elfilter. Analys av moejligheterna

    Energy Technology Data Exchange (ETDEWEB)

    Roennbaeck, Marie; Gustavsson, Lennart [Swedish National Testing and Research Inst., Boraas (Sweden)

    2006-11-15

    Dust particles in flue gas larger than 1 {mu}m are well separated by conventional techniques, while submicron particles are poorly separated. As the use of biofuels with high ash content is increasing, as well as knowledge about negative health effects from inhalation of submicron particles, the interest for reduction of emissions of submicron particles will probably increase. The aim of this project is to investigate possible techniques for separation of submicron particles during flue gas condensation through modification of conventional technique, or with available techniques not usually used with combustion of biofuels, e.g. a wet electrostatic precipitator. Mechanisms for separation of dust particles are briefly described. Cyclones separates particles larger than about 1 {mu}m. Fabric filters separates all particles sizes, but the efficiency reduces as the size reduces. In flue gas condensers and scrubbers the speed and size of water droplets are important for the reduction efficiency. Dry electrostatic precipitators work for all particle sizes, but with reduced efficiency for sizes between 0.1 and 3 {mu}m. Wet electrostatic precipitators separates submicron particles much better. One reason for this is that the potential between the electrodes can be higher. Among conventional flue gas condensers and scrubbers there are two types that, properly designed, can separate submicron particles, namely 'type venturi scrubbers', i.e. a scrubber where a high flue gas velocity is used to form many, small water droplets by friction forces in a nozzle, and 'type scrubber with nozzles', i.e. a scrubber where nozzles supply droplets to the flue gas. For a scrubber with nozzles, the falling velocity of the droplets must be lower and the size smaller than is common today. Also the wet electrostatic precipitator separates submicron particles with high efficiency. They are used today mainly for problematic particles, e.g. sticky or corrosive ones, or for

  2. Process Intensification in Crystallization : Submicron Particle Generation Using Alternative Energy Forms

    NARCIS (Netherlands)

    Radacsi, N.

    2012-01-01

    Crystallization is one of the oldest separation and product formation techniques that continues to be in use today. Despite its long history, it only started to develop significantly in the past few decades. In this thesis, the application of Process Intensification in crystallization is

  3. Process Intensification in Crystallization: Submicron Particle Generation Using Alternative Energy Forms

    OpenAIRE

    Radacsi, N.

    2012-01-01

    Crystallization is one of the oldest separation and product formation techniques that continues to be in use today. Despite its long history, it only started to develop significantly in the past few decades. In this thesis, the application of Process Intensification in crystallization is investigated. Process Intensification is a set of often radically innovative principles in process and equipment design, which can bring significant benefits in terms of process and chain efficiency, capital ...

  4. Development of high efficient ESP for submicron particle collection. Sabumikuron ryushi no kokoritsu shujin hoshiki no kaihatsu. ; Seiden gyoshu sochi naizo denki shujin hoshiki no gyoshusayo to shujin koritsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T.; Suda, T.

    1989-11-01

    The result of testing the operation of an electrostatic agglomeration appratus (ESA) is reported, which has been developed at Central Research Institute of Electric Power Industry (CRIEPI). Details of the apparatus is given in the authors {prime} previous papaer (1988). At first a description is given of an apparatus which produces the aerosol for laboratory use comprising submicron-sized carbon particles and micron-sized flyash particles. This aerosol is similar in quality to that produced by a combustion furnance at CRIEPI. An apparatus provided with mesh electrodes for charging aerosol particles is also developed. Thus preparing aerosol samples, the effect of agglomeration produced by the ESA On the samples is examined to demonstrate that particle sizes in diameter are increased by a factor of four on average and the percentage of submicron-sized particles (less than 1 {mu} m in diameter) is reduced by 20% in weight. Combined with this type of ESA, the efficiency of ESP (electrostatic precipitator) in collecting submicron-sized particles is theoretically calculated to increase by about 1 - 3% when it is used at a thermal power plant of 520MW. 4refs., 21 figs., 6 tabs.

  5. Organic composition of single and submicron particles in different regions of western North America and the eastern Pacific during INTEX-B 2006

    Directory of Open Access Journals (Sweden)

    D. A. Day

    2009-08-01

    Full Text Available Single particles were collected from an aircraft platform as part of the Intercontinental Chemical Transport Experiment – Phase B (INTEX-B conducted over the eastern Pacific and western North America. Single particle spectra were obtained using scanning transmission X-ray microscopy-near edge X-ray absorption fine structure spectroscopy (STXM-NEXAFS. Bulk submicron particles were also collected and organic functional group and elemental concentrations were quantified with Fourier transform infrared (FTIR spectroscopy and X-ray fluorescence (XRF. Single particle spectra were classified into metaclasses associated with different sources and atmospheric processing. Particles with spectra indicative of secondary organic aerosol production and combustion sources were found at several locations and a range of altitudes. At lower altitudes, particles with spectra resembling soil dust and biomass burning fingerprints were commonly observed. The types of particle spectra most commonly observed aloft were similar to those observed during a previous study over the northwestern Pacific, indicating that long-range transport may have been an important particle source. Single particle spectra provided evidence that condensation and surface-limited oxidation contributed to particle growth. Organic mass (OM concentrations ranged from 1 to 7 μg m−3 and averaged 2.4–4.1 μg m−3. Alkane functional groups were the largest fraction of OM, averaging 1.9–2.1 μg m−3 or 50–76% of OM, followed by alcohol functional groups (0.35–0.39 μg m−3, 9–14%. Organic and elemental concentrations are compared within and among geographical air mass regions: "Pacific" free troposphere, "Continental" free troposphere, "Seattle" metropolitan region, and the California "Central Valley". OM concentrations were highest and most variable in the Central Valley (3.5±2 μg m−3. Oxygen-to-carbon ratios were

  6. Hygroscopicity of Chemically Aged, sub-micron Squalane Particles: On the Role of Size and Composition towards the Hygroscopicity Parameter κ

    Science.gov (United States)

    Harmon, C. W.; Smith, J. D.; Che, D. L.; Leone, S. R.; Wilson, K. R.

    2010-12-01

    Measurements presented herein explore cloud condensation nuclei (CCN) activity of sub-micron squalane particles chemically aged by hydroxyl radicals as a function of size and OH exposure. As squalane particles are exposed to OH radicals, size-selected 100, 150, and 200 nm particles monotically decrease in size with increasing OH exposure. Concurrently, their CCN derived hygroscopicity parameter values, κ, increase with OH exposure until saturating at 0.165 in the 100 nm data set, 0.140 in the 150 nm data set, and reach a maximum value of 0.075 in the 200 nm data set at the highest level of OH exposure. The critical super-saturation relative humidity (RH) at which CCN activity is achieved decreases initially with increasing OH exposure and then increases with OH exposure, most notably for the 100 nm data set and weakly with the 150 nm data set. Chemically aged squalane particles from the 200 nm data set show a monotonic decrease in critical super-saturation RH with all values of increasing OH exposure between 0.1-2.5 × 10^13 s molec./cc. The measured O:C ratios of 160 nm chemically aged squalane particles, which were reported previously, are compared to κ values by the CCN derived relationship reported in literature: κ = 0.30*O:C and reasonable agreement is attained in the size-selected 150 nm data set. These values are also compared with the hygroscopic growth factor derived relationship in literature: κ = 0.49*(O:C -0.25) and reasonable agreement is attained at O:C > 0.35.

  7. Emissions of soot particles from heat generators

    Science.gov (United States)

    Lyubov, V. K.; Popov, A. N.; Popova, E. I.

    2017-11-01

    «Soot carbon» or «Soot» - incomplete combustion or thermal decomposition particulate carbon product of hydrocarbons consisting of particles of various shapes and sizes. Soot particles are harmful substances Class 2 and like a dust dispersed by wind for thousands of kilometers. Soot have more powerful negative factor than carbon dioxide. Therefore, more strict requirements on ecological and economical performance for energy facilities at Arctic areas have to be developed to protect fragile Arctic ecosystems and global climate change from degradation and destruction. Quantity of soot particles in the flue gases of energy facilities is a criterion of effectiveness for organization of the burning process. Some of heat generators do not provide the required energy and environmental efficiency which results in irrational use of energy resources and acute pollution of environment. The paper summarizes the results of experimental study of solid particles emission from wide range of capacity boilers burning different organic fuels (natural gas, fuel oil, coal and biofuels). Special attention is paid to environmental and energy performance of the biofuels combustion. Emissions of soot particles PM2.5 are listed. Structure, composition and dimensions of entrained particles with the use of electronic scanning microscope Zeiss SIGMA VP were also studied. The results reveal an impact of several factors on soot particles emission.

  8. Enhancement of nonlinear optical and temperature dependent dielectric properties of Ce:BaTiO3 nano and submicron particles

    Science.gov (United States)

    Senthilkumar, P.; Dhanuskodi, S.; Thomas, Anitta Rose; Philip, Reji

    2017-08-01

    The solgel synthesized Ce: BaTiO3 (BT) particles are crystallized in tetragonal structure and the expansion of lattice along a-axis is ensured from the Rietveld refined XRD spectra. FTIR shows that the increase of force constant from 199.97 to 213.13 N m-1 is owing to an effective incorporation of heavier atomic mass of Ce in BT lattice. HRTEM reflects the discontinuous atomic planes in the form of Ti vacancies which is supported by EDS measurement. The modification of optical band structure of BT with Ce ions is validated through several absorption and defect emission bands. Energy dependent second harmonic generation is carried out to confirm the non saturated signal, thermal stability and maximum intensity 2483 counts attained for 2 mol% Ce at 200 mJ. Optical limiting characteristics of the samples is analysed at 532 nm using 5 ns laser pulses of energy 50, 100 and 150 µJ. The nonlinear absorption coefficient (β) is found to be enhanced upon Ce doping. Lower optical limiting thresholds of 2.8 and 3.3 J cm-2 are obtained in the case of 1 and 4 mol% Ce samples respectively. Dielectric properties in a broad temperature range (40-500 °C) and frequency (100 Hz-5 MHz) have been investigated in detail. The dielectric constant is increased from 1926 to 3750 on Ce doping and there are two semicircles in the Cole-Cole plot at 500 °C due to grain and grain boundaries and corresponding equivalent circuit model is proposed.

  9. Sub-micron particle behaviour and capture at an immuno-sensor surface in an ultrasonic standing wave.

    Science.gov (United States)

    Kuznetsova, Larisa A; Martin, Stacey P; Coakley, W Terence

    2005-12-15

    The capture of 200 nm biotinylated latex beads from suspensions of concentration 10(7) to 2.5 x 10(8) particle/ml on an immuno-coated surface of the acoustic reflector in an ultrasound standing wave (USW) resonator has been studied while the acoustic pathlength was less than one half wavelength (lambda/2). The particles were delivered to the reflector's surface by acoustically induced flow. The capture dependencies on suspension concentration, duration of experiments and acoustic pressure have been established at 1.09, 1.46 and 1.75 MHz. Five-fold capture increase has been obtained at 1.75 MHz in comparison to the control (no ultrasound) situation. The contrasting behaviours of 1, 0.5 and 0.2 mum fluorescent latex beads in a lambda/4 USW resonator at 1.46 MHz have been characterized. The particle movements were observed with an epi-fluorescent microscope and the velocities of the particles were measured by particle image velocimetry (PIV). The experiments showed that whereas the trajectories of 1 mum particles were mainly affected by the direct radiation force, 0.5 mum particles were influenced both by the radiation force and acoustic streaming. The 0.2 mum latex beads followed acoustic streaming in the chamber and were not detectably affected by the radiation force. The streaming-associated behaviour of the 200 nm particles has implications for enhanced immunocapture of viruses and macromolecules (both of which are also too small to experience significant acoustic radiation force).

  10. The role of jet and film drops in controlling the mixing state of submicron sea spray aerosol particles.

    Science.gov (United States)

    Wang, Xiaofei; Deane, Grant B; Moore, Kathryn A; Ryder, Olivia S; Stokes, M Dale; Beall, Charlotte M; Collins, Douglas B; Santander, Mitchell V; Burrows, Susannah M; Sultana, Camille M; Prather, Kimberly A

    2017-07-03

    The oceans represent a significant global source of atmospheric aerosols. Sea spray aerosol (SSA) particles comprise sea salts and organic species in varying proportions. In addition to size, the overall composition of SSA particles determines how effectively they can form cloud droplets and ice crystals. Thus, understanding the factors controlling SSA composition is critical to predicting aerosol impacts on clouds and climate. It is often assumed that submicrometer SSAs are mainly formed by film drops produced from bursting bubble-cap films, which become enriched with hydrophobic organic species contained within the sea surface microlayer. In contrast, jet drops formed from the base of bursting bubbles are postulated to mainly produce larger supermicrometer particles from bulk seawater, which comprises largely salts and water-soluble organic species. However, here we demonstrate that jet drops produce up to 43% of total submicrometer SSA number concentrations, and that the fraction of SSA produced by jet drops can be modulated by marine biological activity. We show that the chemical composition, organic volume fraction, and ice nucleating ability of submicrometer particles from jet drops differ from those formed from film drops. Thus, the chemical composition of a substantial fraction of submicrometer particles will not be controlled by the composition of the sea surface microlayer, a major assumption in previous studies. This finding has significant ramifications for understanding the factors controlling the mixing state of submicrometer SSA particles and must be taken into consideration when predicting SSA impacts on clouds and climate.

  11. The role of jet and film drops in controlling the mixing state of submicron sea spray aerosol particles

    Science.gov (United States)

    Wang, Xiaofei; Deane, Grant B.; Moore, Kathryn A.; Ryder, Olivia S.; Stokes, M. Dale; Beall, Charlotte M.; Collins, Douglas B.; Santander, Mitchell V.; Burrows, Susannah M.; Sultana, Camille M.; Prather, Kimberly A.

    2017-07-01

    The oceans represent a significant global source of atmospheric aerosols. Sea spray aerosol (SSA) particles comprise sea salts and organic species in varying proportions. In addition to size, the overall composition of SSA particles determines how effectively they can form cloud droplets and ice crystals. Thus, understanding the factors controlling SSA composition is critical to predicting aerosol impacts on clouds and climate. It is often assumed that submicrometer SSAs are mainly formed by film drops produced from bursting bubble-cap films, which become enriched with hydrophobic organic species contained within the sea surface microlayer. In contrast, jet drops formed from the base of bursting bubbles are postulated to mainly produce larger supermicrometer particles from bulk seawater, which comprises largely salts and water-soluble organic species. However, here we demonstrate that jet drops produce up to 43% of total submicrometer SSA number concentrations, and that the fraction of SSA produced by jet drops can be modulated by marine biological activity. We show that the chemical composition, organic volume fraction, and ice nucleating ability of submicrometer particles from jet drops differ from those formed from film drops. Thus, the chemical composition of a substantial fraction of submicrometer particles will not be controlled by the composition of the sea surface microlayer, a major assumption in previous studies. This finding has significant ramifications for understanding the factors controlling the mixing state of submicrometer SSA particles and must be taken into consideration when predicting SSA impacts on clouds and climate.

  12. Consideration of the respiratory cycle asymmetry in the numerical modeling of the submicron particles deposition in the human nasal cavity

    Science.gov (United States)

    Ganimedov, V. L.; Muchnaya, M. I.

    2017-10-01

    A detailed study of the behavior of the U-shaped curve was conducted, which described deposition efficiency of inhaled particles in human nasal cavity. The particles in the range from 1 nm to 20 µm are considered. Calculations of air flow and particles deposition were carried out for symmetrical (idealized) and asymmetrical (real) breathing cycles at the same volume of inhaled air, which corresponded to calm breathing. The calculations were performed on the base of the mathematical model of the nasal cavity of healthy person using software package ANSYS (FLUENT 12). The comparison of the results was made between these calculations, and also with the results obtained at quasi-stationary statement of the problem for several values of flow rate. The comparison of the results of quasi-stationary calculations with available calculated and experimental data (in vivo i in vitro) was fulfilled previously. Good agreement of the results was obtained. It is shown that the real distribution of deposition efficiency as a function of the particle size can be obtained via a certain combination of the results of quasi-stationary calculations, without the use of laborious and time-consuming non-stationary calculation.

  13. Highly porous acrylonitrile-based submicron particles for UO2(2+) absorption in an immunosensor assay.

    Science.gov (United States)

    Sahiner, Nurettin; Yu, Haini; Tan, Grace; He, Jibao; John, Vijay T; Blake, Diane A

    2012-01-01

    Our laboratory has previously reported an antibody-based assay for hexavalent uranium (UO(2)(2+)) that could be used on-site to rapidly assess uranium contamination in environmental water samples (Melton, S. J.; et al. Environ. Sci. Technol. 2009, 43, 6703-6709). To extend the utility of this assay to less-characterized sites of uranium contamination, we required a uranium-specific adsorbent that would rapidly remove the uranium from groundwater samples, while leaving the concentrations of other ions in the groundwater relatively unaltered. This study describes the development of hydrogel particles containing amidoxime groups that can rapidly and selectively facilitate the uptake of uranyl ions. A miniemulsion polymerization technique using SDS micelles was employed for the preparation of the hydrogel as linked submicrometer particles. In polymerization, acrylonitrile was used as the initial monomer, ethylene glycol dimethacrylate as the crosslinker and 2-hydroxymethacrylate, 1-vinyl-2-pyrrolidone, acrylic acid, or methacrylic acid were added as co-monomers after the initial seed polymerization of acrylonitrle. The particles were characterized by transmission electron spectroscopy, scanning electron microscopy (SEM) and cryo-SEM. The amidoximated particles were superior to a commercially available resin in their ability to rapidly remove dissolved UO(2)(2+) from spiked groundwater samples. © 2011 American Chemical Society

  14. Visualization and quantification of four steps in magnetic field induced two-dimensional ordering of superparamagnetic submicron particles

    DEFF Research Database (Denmark)

    Gajula, Gnana Prakash; Neves Petersen, Teresa; Petersen, Steffen B.

    2010-01-01

    , resolved growth steps (condensation, polarization, co-linearity and concatenation), the average chain growth rate, and inter-particle interaction length were calculated in the presence of a 120 G external magnetic field using optical microscopy and ‘in-house' developed image analysis software...

  15. Influence of biomass burning on mixing state of sub-micron aerosol particles in the North China Plain

    Science.gov (United States)

    Kecorius, Simonas; Ma, Nan; Teich, Monique; van Pinxteren, Dominik; Zhang, Shenglan; Gröβ, Johannes; Spindler, Gerald; Müller, Konrad; Iinuma, Yoshiteru; Hu, Min; Herrmann, Hartmut; Wiedensohler, Alfred

    2017-09-01

    Particulate emissions from crop residue burning decrease the air quality as well as influence aerosol radiative properties on a regional scale. The North China Plain (NCP) is known for the large scale biomass burning (BB) of field residues, which often results in heavy haze pollution episodes across the region. We have been able to capture a unique BB episode during the international CAREBeijing-NCP intensive field campaign in Wangdu in the NCP (38.6°N, 115.2°E) from June to July 2014. It was found that aerosol particles originating from this BB event showed a significantly different mixing state compared with clean and non-BB pollution episodes. BB originated particles showed a narrower probability density function (PDF) of shrink factor (SF). And the maximum was found at shrink factor of 0.6, which is higher than in other episodes. The non-volatile particle number fraction during the BB episode decreased to 3% and was the lowest measured value compared to all other predefined episodes. To evaluate the influence of particle mixing state on aerosol single scattering albedo (SSA), SSA at different RHs was simulated using the measured aerosol physical-chemical properties. The differences between the calculated SSA for biomass burning, clean and pollution episodes are significant, meaning that the variation of SSA in different pollution conditions needs to be considered in the evaluation of aerosol direct radiative effects in the NCP. And the calculated SSA was found to be quite sensitive on the mixing state of BC, especially at low-RH condition. The simulated SSA was also compared with the measured values. For all the three predefined episodes, the measured SSA are very close to the calculated ones with assumed mixing states of homogeneously internal and core-shell internal mixing, indicating that both of the conception models are appropriate for the calculation of ambient SSA in the NCP.

  16. Seasonal variations of ultra-fine and submicron aerosols in Taipei, Taiwan: implications for particle formation processes in a subtropical urban area

    Directory of Open Access Journals (Sweden)

    H. C. Cheung

    2016-02-01

    Full Text Available The aim of this study is to investigate the seasonal variations in the physicochemical properties of atmospheric ultra-fine particles (UFPs, d ≤ 100 nm and submicron particles (PM1, d ≤ 1 µm in an east Asian urban area, which are hypothesized to be affected by the interchange of summer and winter monsoons. An observation experiment was conducted at TARO (Taipei Aerosol and Radiation Observatory, an urban aerosol station in Taipei, Taiwan, from October 2012 to August 2013. The measurements included the mass concentration and chemical composition of UFPs and PM1, as well as the particle number concentration (PNC and the particle number size distribution (PSD with size range of 4–736 nm. The results indicated that the mass concentration of PM1 was elevated during cold seasons with a peak level of 18.5 µg m−3 in spring, whereas the highest concentration of UFPs was measured in summertime with a mean of 1.64 µg m−3. Moreover, chemical analysis revealed that the UFPs and PM1 were characterized by distinct composition; UFPs were composed mostly of organics, whereas ammonium and sulfate were the major constituents of PM1. The seasonal median of total PNCs ranged from 13.9  ×  103 cm−3 in autumn to 19.4  ×  103 cm−3 in spring. Median concentrations for respective size distribution modes peaked in different seasons. The nucleation-mode PNC (N4 − 25 peaked at 11.6  ×  103 cm−3 in winter, whereas the Aitken-mode (N25 − 100 and accumulation-mode (N100 − 736 PNC exhibited summer maxima at 6.0  ×  103 and 3.1  ×  103 cm−3, respectively. The change in PSD during summertime was attributed to the enhancement in the photochemical production of condensable organic matter that, in turn, contributed to the growth of aerosol particles in the atmosphere. In addition, clear photochemical production of particles was observed, mostly in the summer season

  17. Effect of poly(vinyl alcohol (PVA wear particles generated in water lubricant on immune response of macrophage

    Directory of Open Access Journals (Sweden)

    S. Omata

    2015-03-01

    Full Text Available To develop a novel biotribological material for artificial cartilage implant with a lubricity supplement of the joint surface, we focused on two types of poly(vinyl alcohol (PVA hydrogel: repeated freeze–thawing (PVA-FT and cast-drying (PVA-CD gels. Here we observed the morphology of wear particles generated during a reciprocating wear test and assessed macrophage immune responses by applying hydrogel wear particles. As a result, PVA-CD had a significantly lower total amount of wear than did PVA-FT. The size distributions of PVA-FT and -CD wear particles were similar. Most of the particles were nanoparticles up to approximately 50 nm in diameter. Considering the particle volume distribution, there were very few micron- and submicron-sized wear particles around 1 μm in diameter. In SEM observations of dried PVA wear particles, both distributions of wear particles of PVA-FT and -CD were similar. Micron-sized wear particles were chiefly formed by close packing of 20- to 50-nm-sized particles. Biochemical and immunological evaluations revealed no cytotoxic effects of wear particles on macrophages. Cytokine synthesis of both wear particle-stimulated groups was significantly lower than that of the lipopolysaccharide-stimulated positive control. Therefore, it is suggested that PVA wear particles do not affect the macrophage immune response.

  18. Exposure to submicron particles (PM1.0) from diesel exhaust and pollen allergens of human lung epithelial cells induces morphological changes of mitochondria tonifilaments and rough endoplasmic reticulum.

    Science.gov (United States)

    Mazzarella, Gennaro; Lucariello, Angela; Bianco, Andrea; Calabrese, Cecilia; Thanassoulas, Theodoros; Savarese, Leonilde; Fiumarella, Angelamaria; Esposito, Vincenzo; DE Luca, Antonio

    2014-01-01

    In recent literature, little has been said regarding the morphological changes that occur in lung cells after treatment with particles and nanoparticles. Using an in vitro model of type-II lung epithelium (A549), we studied the effects of submicron particles (PM1.0), Parietaria officinalis (ALL), and PM1.0 + ALL together. To date several biochemical effects have been described, instead few data exist in literature regarding morphological events following these treatments, in particular we focused on the morphological changes and distribution of mitochondria, tonifilaments and rough endoplasmic reticulum, using a transmission electron microscopic (TEM) approach. After exposure to PM1.0 particles (PM1.0), Parietaria officinalis as allergen, and PM1.0 with P. officinalis, changes in the cytoplasmic area were observed, such as damage to mitochondria and morphological alterations of the tonifilaments and rough endoplasmic reticulum. The data obtained strongly support the hypothesis that cells in contact with submicron particles (PM1.0), or P. officinalis, undergo alteration of their metabolism. Copyright © 2014 International Institute of Anticancer Research (Dr. John G. Delinassios), All rights reserved.

  19. Characterization of submicron particles influenced by mixed biogenic and anthropogenic emissions using high-resolution aerosol mass spectrometry: results from CARES

    Energy Technology Data Exchange (ETDEWEB)

    Setyan, Ari; Zhang, Qi; Merkel, M.; Knighton, Walter B.; Sun, Y.; Song, Chen; Shilling, John E.; Onasch, Timothy B.; Herndon, Scott C.; Worsnop, Douglas R.; Fast, Jerome D.; Zaveri, Rahul A.; Berg, Larry K.; Wiedensohler, A.; Flowers, B. A.; Dubey, Manvendra K.; Subramanian, R.

    2012-09-11

    The Carbonaceous Aerosols and Radiative Effects Study (CARES) took place in the Sacramento Valley of California in summer 2010. We present results obtained at Cool, CA, the T1 site of the project ({approx}40 km downwind of urban emissions from Sacramento), where we deployed an Aerodyne high resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) in parallel with complementary instrumentation to characterize the sources and processes of submicron particles (PM1). Cool is located at the foothill of the Sierra Nevada Mountains, where intense biogenic emissions are periodically mixed with urban outflow transported by daytime southwesterly winds from the Sacramento metropolitan area. The particle mass loading was low (3.0 {micro}gm{sup -3} on average) and dominated by organics (80% of the PM1 mass) followed by sulfate (9.9 %). Organics and sulfate appeared to be externally mixed, as suggested by their different time series (r2 = 0.13) and size distributions. Sulfate showed a bimodal distribution with a droplet mode peaking at {approx}400nm in vacuum aerodynamic diameter (Dva), and a condensation mode at {approx}150 nm, while organics generally displayed a broad distribution in 60-600nm (Dva). New particle formation and growth events were observed almost every day, emphasizing the roles of organics and sulfate in new particle growth, especially that of organics. The organic aerosol (OA) had a nominal formula of C{sub 1}H{sub 1.38}N{sub 0.004}O{sub 0.44}, thus an average organic mass-to-carbon (OM/OC) ratio of 1.70. Two different oxygenated OA (OOA, 90% of total OA mass) and a hydrocarbon-like OA (HOA, 10 %) were identified by Positive matrix factorization (PMF) of the high resolution mass spectra. The more oxidized MO-OOA (O/C = 0.54) corresponded to secondary OA (SOA) primarily influenced by biogenic emissions, while the less oxidized LO-OOA (O/C = 0.42) corresponded to SOA associated with urban transport. The HOA factor corresponded to primary emissions mainly

  20. High-performance UV and DUV lenses for projection-lithographic generation of submicron patterns down to 0.4 μm

    Science.gov (United States)

    Merkel, Klaus; Hofmann, Christian

    1990-07-01

    Manufacturing of modern microelectronic circuits requires projection- lithographic generation of submicron patterns by using high-aperture diffraction-limited UV- and DUV-lenses. Realized image quality of such high-performance leiises is mainly determined by the control of the extremly narrowed fabrication tolerances by new developed special high technologies for production and measurement of such lenses1. Contactless optical precision measurement of surfacy topography, thickness, distances, and decentring of optical elements , computer-controlled correction polishing" , manufacturing of nanometer-asperic surfaces by CNC-correction polishing or by ion-beam etching, computer-assisted assembly , wave- front analysis on the basis of measurement of geometrical-optical beam aberrations, and image quality testing with near-coherent illumination are such new techniques. The correction of such lenses is more difficult because the available optical media are limited to those which sufficiently good transmission in the UV resp. DUV region. Optical media used in DUV-lenses are fused silica glass, calcium or barium fluoride, and eventually fluorphosphate crown glass. This media restriction leads to an increase in number of lenses, constructional length, and technological difficulties in the manufacturing.

  1. Submicron and nano formulations of titanium dioxide and zinc oxide stimulate unique cellular toxicological responses in the green microalga Chlamydomonas reinhardtii

    Energy Technology Data Exchange (ETDEWEB)

    Gunawan, Cindy, E-mail: c.gunawan@unsw.edu.au [ARC Centre of Excellence for Functional Nanomaterials, School of Chemical Engineering, The University of New South Wales, Sydney, NSW (Australia); Sirimanoonphan, Aunchisa [ARC Centre of Excellence for Functional Nanomaterials, School of Chemical Engineering, The University of New South Wales, Sydney, NSW (Australia); Teoh, Wey Yang [Clean Energy and Nanotechnology (CLEAN) Laboratory, School of Energy and Environment, City University of Hong Kong, Kowloon, Hong Kong Special Administrative Region (Hong Kong); Marquis, Christopher P., E-mail: c.marquis@unsw.edu.au [School of Biotechnology and Biomolecular Sciences, The University of New South Wales, Sydney, NSW (Australia); Amal, Rose [ARC Centre of Excellence for Functional Nanomaterials, School of Chemical Engineering, The University of New South Wales, Sydney, NSW (Australia)

    2013-09-15

    Highlights: • Uptake of TiO{sub 2} solids by C. reinhardtii generates ROS as an early stress response. • Submicron and nanoTiO{sub 2} exhibit benign effect on cell proliferation. • Uptake of ZnO solids and leached zinc by C. reinhardtii inhibit the alga growth. • No cellular oxidative stress is detected with submicron and nano ZnO exposure. • The toxicity of particles is not necessarily mediated by cellular oxidative stress. -- Abstract: The work investigates the eco-cytoxicity of submicron and nano TiO{sub 2} and ZnO, arising from the unique interactions of freshwater microalga Chlamydomonas reinhardtii to soluble and undissolved components of the metal oxides. In a freshwater medium, submicron and nano TiO{sub 2} exist as suspended aggregates with no-observable leaching. Submicron and nano ZnO undergo comparable concentration-dependent fractional leaching, and exist as dissolved zinc and aggregates of undissolved ZnO. Cellular internalisation of solid TiO{sub 2} stimulates cellular ROS generation as an early stress response. The cellular redox imbalance was observed for both submicron and nano TiO{sub 2} exposure, despite exhibiting benign effects on the alga proliferation (8-day EC50 > 100 mg TiO{sub 2}/L). Parallel exposure of C. reinhardtii to submicron and nano ZnO saw cellular uptake of both the leached zinc and solid ZnO and resulting in inhibition of the alga growth (8-day EC50 ≥ 0.01 mg ZnO/L). Despite the sensitivity, no zinc-induced cellular ROS generation was detected, even at 100 mg ZnO/L exposure. Taken together, the observations confront the generally accepted paradigm of cellular oxidative stress-mediated cytotoxicity of particles. The knowledge of speciation of particles and the corresponding stimulation of unique cellular responses and cytotoxicity is vital for assessment of the environmental implications of these materials.

  2. Role of ammonium ion and transition metals in the formation of secondary organic aerosol and metallo-organic complex within fog processed ambient deliquescent submicron particles collected in central part of Indo-Gangetic Plain.

    Science.gov (United States)

    Singh, Dharmendra Kumar; Gupta, Tarun

    2017-08-01

    In this study we observed the role of ammonium ion (NH4+) and transition metals (Fe, Mn, Cr, and Cu) present in ambient submicron particles in stabilizing and enhancing the yield of water soluble organic carbon (WSOC). A good correlation of WSOC with transition metals and NH4+ was found (R2 = 0.87 and 0.71), respectively within foggy episode collected ambient PM1 (particles having aerodynamic diameter ≤1.0 μm) suggesting plausibleness of alternate oxidation (primarily various carbonyls into their respective organic acids, esters and other derivatives.) and aging mechanisms. Molar concentration of ammonium ion was observed to be exceeded over and above to require in neutralizing the sulphate and nitrate which further hints its role in the neutralization, stabilization and enhancement of subset of WSOC such as water soluble organic acids. Transition metals were further apportioned using enrichment factor analysis. The source of Fe, Mn, and Cr was found to be crustal and Cu was tagged to anthropogenic origin. This study also described the plausible role of significant predictors (Fe and Cu) in the secondary organic aerosol (SOA) formation through effect of Fenton chemistry. Mass-to-charge ratio of identified oxalic acid from our published recent field study (carried out from same sampling location) was used for understanding the possible metallo-organic complex with Fe supports the substantial role of Fe in SOA formation in the deliquescent submicron particles facilitated by aqueous-phase chemistry. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Aerodynamics and deposition effects of inhaled submicron drug aerosol in airway diseases.

    Science.gov (United States)

    Faiyazuddin, Md; Mujahid, Md; Hussain, Talib; Siddiqui, Hefazat H; Bhatnagar, Aseem; Khar, Roop K; Ahmad, Farhan J

    2013-01-01

    Particle engineering is the prime focus to improve pulmonary drug targeting with the splendor of nanomedicines. In recent years, submicron particles have emerged as prettyful candidate for improved fludisation and deposition. For effective deposition, the particle size must be in the range of 0.5-5 μm. Inhalers design for the purpose of efficient delivery of powders to lungs is again a crucial task for pulmonary scientists. A huge number of DPI devices exist in the market, a significant number are awaiting FDA approval, some are under development and a large number have been patented or applied for patent. Even with superior design, the delivery competence is still deprived, mostly due to fluidisation problems which cause poor aerosol generation and deposition. Because of the cohesive nature and poor flow characteristics, they are difficult to redisperse upon aerosolization with breath. These problems are illustrious in aerosol research, much of which is vastly pertinent to pulmonary therapeutics. A technical review is presented here of advances that have been utilized in production of submicron drug particles, their in vitro/in vivo evaluations, aerosol effects and pulmonary fate of inhaled submicron powders.

  4. Dust generation in powders: Effect of particle size distribution

    OpenAIRE

    Chakravarty Somik; Le Bihan Olivier; Fischer Marc; Morgeneyer Martin

    2017-01-01

    This study explores the relationship between the bulk and grain-scale properties of powders and dust generation. A vortex shaker dustiness tester was used to evaluate 8 calcium carbonate test powders with median particle sizes ranging from 2μm to 136μm. Respirable aerosols released from the powder samples were characterised by their particle number and mass concentrations. All the powder samples were found to release respirable fractions of dust particles which end up decreasing with time. Th...

  5. Particle size analysis of amalgam powder and handpiece generated specimens.

    Science.gov (United States)

    Drummond, J L; Hathorn, R M; Cailas, M D; Karuhn, R

    2001-07-01

    The increasing interest in the elimination of amalgam particles from the dental waste (DW) stream, requires efficient devices to remove these particles. The major objective of this project was to perform a comparative evaluation of five basic methods of particle size analysis in terms of the instrument's ability to quantify the size distribution of the various components within the DW stream. The analytical techniques chosen were image analysis via scanning electron microscopy, standard wire mesh sieves, X-ray sedigraphy, laser diffraction, and electrozone analysis. The DW particle stream components were represented by amalgam powders and handpiece/diamond bur generated specimens of enamel; dentin, whole tooth, and condensed amalgam. Each analytical method quantified the examined DW particle stream components. However, X-ray sedigraphy, electrozone, and laser diffraction particle analyses provided similar results for determining particle distributions of DW samples. These three methods were able to more clearly quantify the properties of the examined powder and condensed amalgam samples. Furthermore, these methods indicated that a significant fraction of the DW stream contains particles less than 20 microm. The findings of this study indicated that the electrozone method is likely to be the most effective technique for quantifying the particle size distribution in the DW particle stream. This method required a relative small volume of sample, was not affected by density, shape factors or optical properties, and measured a sufficient number of particles to provide a reliable representation of the particle size distribution curve.

  6. Nonperturbative mechanism for elementary particle mass generation

    Science.gov (United States)

    Frezzotti, R.; Rossi, G. C.

    2015-09-01

    Taking inspiration from lattice QCD data, we argue that a finite nonperturbative contribution to the quark mass is generated as a consequence of the dynamical phenomenon of spontaneous chiral symmetry breaking, in turn triggered by the explicit breaking of chiral symmetry induced by the critical Wilson term in the action. In pure lattice QCD this mass term cannot be separated from the unavoidably associated linearly divergent contribution. However, if QCD is enlarged to a theory where also a scalar field is present, coupled to an SU(2) doublet of fermions via a Yukawa and a Wilson-like term, then in the phase where the scalar field takes a nonvanishing expectation value, a dynamically generated and "naturally" light fermion mass (numerically unrelated to the expectation value of the scalar field) is conjectured to emerge at a critical value of the Yukawa coupling where the symmetry of the model is maximally enhanced. Masses dynamically generated in this way display a natural hierarchy according to which the stronger is the strongest of the interactions the fermion is subjected to, the larger will be its mass.

  7. Ultrafine particle removal and generation by portable air cleaners

    Science.gov (United States)

    Waring, Michael S.; Siegel, Jeffrey A.; Corsi, Richard L.

    Portable air cleaners can both remove and generate pollutants indoors. To investigate these phenomena, we conducted a two-phase investigation in a 14.75 m 3 stainless steel chamber. In the first phase, particle size-resolved (12.6-514 nm diameter) clean air delivery rates (CADR) and efficiencies were determined, as were ozone emission rates, for two high-efficiency particle arresting (HEPA) filters, one electrostatic precipitator with a fan, and two ion generators without fans. The two HEPA air cleaners had count average CADR (standard deviation) of 188 (30) and 324 (44) m 3 h -1; the electrostatic precipitator 284 (62) m 3 h -1; and the two ion generators 41 (11) and 35 (13) m 3 h -1. The electrostatic precipitator emitted ozone at a rate of 3.8±0.2 mg h -1, and the two ion generators 3.3±0.2 and 4.3±0.2 mg h -1. Ozone initiates reactions with certain unsaturated organic compounds that produce ultrafine and fine particles, carbonyls, other oxidized products, and free radicals. During the second phase, five different ion generators were operated separately in the presence of a plug-in liquid or solid air freshener, representing a strong terpene source. For air exchange rates of between 0.49 and 0.96 h -1, three ion generators acted as steady-state net particle generators in the entire measured range of 4.61-157 nm, and two generated particles in the range of approximately 10 to 39-55 nm. Terpene and aldehyde concentrations were also sampled for one ion generator, and concentrations of terpenes decreased and formaldehyde increased. Given these results, the pollutant removal benefits of ozone-generating air cleaners may be outweighed by the generation of indoor pollution.

  8. Generating heavy particles with energy and momentum conservation

    Science.gov (United States)

    Mereš, Michal; Melo, Ivan; Tomášik, Boris; Balek, Vladimír; Černý, Vladimír

    2011-12-01

    We propose a novel algorithm, called REGGAE, for the generation of momenta of a given sample of particle masses, evenly distributed in Lorentz-invariant phase space and obeying energy and momentum conservation. In comparison to other existing algorithms, REGGAE is designed for the use in multiparticle production in hadronic and nuclear collisions where many hadrons are produced and a large part of the available energy is stored in the form of their masses. The algorithm uses a loop simulating multiple collisions which lead to production of configurations with reasonably large weights. Program summaryProgram title: REGGAE (REscattering-after-Genbod GenerAtor of Events) Catalogue identifier: AEJR_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEJR_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 1523 No. of bytes in distributed program, including test data, etc.: 9608 Distribution format: tar.gz Programming language: C++ Computer: PC Pentium 4, though no particular tuning for this machine was performed. Operating system: Originally designed on Linux PC with g++, but it has been compiled and ran successfully on OS X with g++ and MS Windows with Microsoft Visual C++ 2008 Express Edition, as well. RAM: This depends on the number of particles which are generated. For 10 particles like in the attached example it requires about 120 kB. Classification: 11.2 Nature of problem: The task is to generate momenta of a sample of particles with given masses which obey energy and momentum conservation. Generated samples should be evenly distributed in the available Lorentz-invariant phase space. Solution method: In general, the algorithm works in two steps. First, all momenta are generated with the GENBOD algorithm. There, particle production is modeled as a sequence of two

  9. Bottom-up synthesis of up-converting submicron-sized Er{sup 3+}-doped LiNbO{sub 3} particles

    Energy Technology Data Exchange (ETDEWEB)

    Jardiel, T., E-mail: jardiel@icv.csic.es [Departamento de Electroceramica, Instituto de Ceramica y Vidrio-CSIC, Kelsen 5, 28049 Madrid (Spain); Caballero, A.C. [Departamento de Electroceramica, Instituto de Ceramica y Vidrio-CSIC, Kelsen 5, 28049 Madrid (Spain); Marin-Dobrincic, M.; Cantelar, E.; Cusso, F. [Departamento de Fisica de Materiales, C-04, Facultad de Ciencias, Universidad Autonoma de Madrid, Avda. Francisco Tomas y Valiente 7, 28049 Madrid (Spain)

    2012-08-15

    A new and simple wet chemical synthesis method is proposed to prepare submicron-sized Erbium-doped LiNbO{sub 3} powders. The synthesis procedure comprises the co-precipitation of lithium and erbium ions from common precursors and their subsequent reaction with niobium ethoxide. A systematic characterization by means of X-Ray Diffraction (XRD), X-ray Fluorescence (XRF), Inductively Coupled Plasma (ICP-OES), Atomic Absorption (AAS), Field Emission Scanning Electron Microscopy (FE-SEM), as well as by the examination of the luminescence properties, evidence that with this method a congruent Er{sup 3+}-doped LiNbO{sub 3} single phase material can be obtained without using complex and time-consuming processing steps. The synthesized powders exhibit efficient IR to VIS up-conversion emissions under 974 nm pumping. -- Highlights: Black-Right-Pointing-Pointer A novel chemical route to the preparation of LiNbO{sub 3} powders has been developed. Black-Right-Pointing-Pointer This process avoids complex and time-consuming processing steps. Black-Right-Pointing-Pointer A congruent Er{sup 3+}-doped LiNbO{sub 3} single phase material can be obtained by this way. Black-Right-Pointing-Pointer The luminescence properties are the expected for this composition.

  10. Hard particle effect on surface generation in nano-cutting

    Science.gov (United States)

    Xu, Feifei; Fang, Fengzhou; Zhang, Xiaodong

    2017-12-01

    The influence of the hard particle on the surface generation, plastic deformation and processing forces in nano-cutting of aluminum is investigated by means of molecular dynamics simulations. In this investigation, a hard particle which is simplified as a diamond ball is embedded under the free surface of workpiece with different depths. The influence of the position of the hard ball on the surface generation and other material removal mechanism, such as the movement of the ball under the action of cutting tool edge, is revealed. The results show that when the hard particle is removed, only a small shallow pit is left on the machined surface. Otherwise, it is pressed down to the subsurface of the workpiece left larger and deeper pit on the generated surface. Besides that, the hard particle in the workpiece would increase the processing force when the cutting tool edge or the plastic carriers interact with the hard particle. It is helpful to optimize the cutting parameters and material properties for obtaining better surface quality in nano-cutting of composites or other materials with micro/nanoscale hard particles in it.

  11. Theoretical assessment of particle generation from sodium pool fires

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M., E-mail: monica.gmartin@ciemat.es [CIEMAT, Unit of Nuclear Safety Research, Av. Complutense, 40, 28040 Madrid (Spain); Herranz, L.E., E-mail: luisen.herranz@ciemat.es [CIEMAT, Unit of Nuclear Safety Research, Av. Complutense, 40, 28040 Madrid (Spain); Kissane, M.P., E-mail: Martin.KISSANE@oecd.org [Nuclear Safety Technology and Regulation Division, OECD Nuclear Energy Agency (NEA), 46 quai Alphonse Le Gallo, 92100 Boulogne-Billancourt (France)

    2016-12-15

    Highlights: • Development of particle generation model for sodium-oxides aerosol formation. • Development of partially validated numerical simulations to build up maps of saturation ratio. • Nucleation of supersaturated vapours as relevant source of aerosols over sodium pools. • Prediction of high concentrations of primary particles in the combustion zone. - Abstract: Potential sodium discharge in the containment during postulated Beyond Design Basis Accidents (BDBAs) in Sodium-cooled Fast Reactors (SFRs) would have major consequences for accident development in terms of energetics and source term. In the containment, sodium vaporization and subsequent oxidation would result in supersaturated oxide vapours that would undergo rapid nucleation creating toxic aerosols. Therefore, modelling this vapour nucleation is essential to proper source term assessment in SFRs. In the frame of the EU-JASMIN project, a particle generation model to calculate the particle generation rate and their primary size during an in-containment sodium pool fire has been developed. Based on a suite of individual models for sodium vaporization, oxygen natural circulation (3D modelling), sodium-oxygen chemical reactions, sodium-oxides-vapour nucleation and condensation, its consistency has been partially validated by comparing with available experimental data. As an outcome, large temperature and vapour concentration gradients set over the sodium pool have been found which result in large particle concentrations in the close vicinity of the pool.

  12. Sea-spray aerosol particles generated in the surf zone

    NARCIS (Netherlands)

    Eijk, A.M.J. van; Kusmierczyk‐Michulec, J.T.; Francius, M.J.; Tedeschi, G.; Piazzola,J.; Merritt, D.L.; Fontana, J.D.

    2011-01-01

    To assess the properties of aerosol particles generated over the surf zone, two experiments were held at the pier of Scripps Institution of Oceanography (SIO), La Jolla CA, and at the pier of the U.S. Army Corps of Engineers Field Research Facility (FRF) in Duck NC. On both sites concentrations of

  13. Hawking Radiation of Mass Generating Particles from Dyonic ...

    Indian Academy of Sciences (India)

    So far, the Higgs mechanism. (Englert & Brout 1964; Higgs 1964) is the experimentally confirmed mechanism to solve the generation of mass problem in particle physics, which satisfies both the unitarity and the renormalization of the theory. In this paper, a brief review for the derivation of the wave equation for the mass.

  14. Synthesis, characterization and electrochemical characterization of lead selenide sub-micron particles capped with a benzoate ligand and prepared at different temperatures

    Science.gov (United States)

    Rodríguez-Rodríguez, Weyshla A.; Colón, Jadiel; Guzmán, Roger; Rivera, Harry; Santiago-Berríos, Mitk'El B.

    2014-09-01

    Semiconductor materials offer several potential benefits as active elements in the development of harvesting-energy conversion technologies. In particular, lead selenide (PbSe) semiconductors have been used and proposed to design solar energy harvesting devices, IR sensors, FET devices, etc. Lead salts have drawn particular attention from the applied and fundamental research communities due to their exceptionally strong quantum confinement effects. Several syntheses of PbSe have been proposed using long chain surfactants to allow the formation of particles and nanoparticles. Here we present a synthesis using benzoic acid as the capping ligand in ambient atmosphere. Although the particles are not in nanometric size, we compare the crystal structure (using x-ray powder diffraction data), the near infrared and mid-infrared absorption properties of PbSe using oleic acid as the capping ligand with PbSe using benzoic acid as the capping ligand. The new synthetized particles were shown to have similar crystal structure and absorb light in the near infrared region at 1410 nm. We also performed cyclic voltammetry of these particles drop-casted in the surface of a glassy carbon electrode. The particles showed electrochemical behavior with an oxidation peak near (-402 ± 5 mV) versus Ag/AgCl reference electrode. The particles seem to form a polymeric film at the surface of a glassy carbon electrode.

  15. Characterization of submicron particles influenced by mixed biogenic and anthropogenic emissions using high-resolution aerosol mass spectrometry: results from CARES

    Directory of Open Access Journals (Sweden)

    A. Setyan

    2012-09-01

    Full Text Available An Aerodyne high resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS was deployed during the Carbonaceous Aerosols and Radiative Effects Study (CARES that took place in northern California in June 2010. We present results obtained at Cool (denoted as the T1 site of the project in the foothills of the Sierra Nevada Mountains, where intense biogenic emissions are periodically mixed with urban outflow transported by daytime southwesterly winds from the Sacramento metropolitan area. During this study, the average mass loading of submicrometer particles (PM1 was 3.0 μg m−3, dominated by organics (80% and sulfate (9.9%. The organic aerosol (OA had a nominal formula of C1H1.38N0.004OM0.44, thus an average organic mass-to-carbon (OM/OC ratio of 1.70. Two distinct oxygenated OA factors were identified via Positive matrix factorization (PMF of the high-resolution mass spectra of organics. The more oxidized MO-OOA (O/C = 0.54 was interpreted as a surrogate for secondary OA (SOA influenced by biogenic emissions whereas the less oxidized LO-OOA (O/C = 0.42 was found to represent SOA formed in photochemically processed urban emissions. LO-OOA correlated strongly with ozone and MO-OOA correlated well with two 1st generation isoprene oxidation products (methacrolein and methyl vinyl ketone, indicating that both SOAs were relatively fresh. A hydrocarbon like OA (HOA factor was also identified, representing primary emissions mainly due to local traffic. On average, SOA (= MO-OOA + LO-OOA accounted for 91% of the total OA mass and 72% of the PM1 mass observed at Cool. Twenty three periods of urban plumes from T0 (Sacramento to T1 (Cool were identified using the Weather Research and Forecasting model coupled with Chemistry (WRF-Chem. The average PM1 mass loading was considerably higher in urban plumes than in air masses dominated by biogenic SOA. The change in OA

  16. Ionizer assisted air filtration for collection of submicron and ultrafine particles-evaluation of long-term performance and influencing factors.

    Science.gov (United States)

    Shi, Bingbing; Ekberg, Lars

    2015-06-02

    Previous research has demonstrated that unipolar ionization can enhance the filter performance to collect airborne particles, aeroallergens, and airborne microorganisms, without affecting the filter pressure drop. However, there is a lack of research on the long-term system performance as well as the influence of environmental and operational parameters. In this paper, both field and laboratory tests were carried out to evaluate the long-term particle collection efficiency of a synthetic filter of class M6 with and without ionization. The effect of air velocity, temperature, relative humidity, and particle concentration were further investigated in laboratory tests. Results showed that ionization enhanced the filtration efficiency by 40%-units during most of the operation time. When the ionization system was managed by periodically switching the ionizer polarity, the filtration efficiency against PM0.3-0.5 was maintained above 50% during half a year. Furthermore, the pressure drop of the ionizer-assisted M6 filter was 25-30% lower than that of a filter of class F7. The evaluation of various influencing factors demonstrated that (1) air moisture reduced the increase of filtration efficiency; (2) higher upstream particle concentration and air velocity decreased the filtration efficiency; and (3) the air temperature had very limited effect on the filtration efficiency.

  17. Separating the signal from the noise: Expanding flow cytometry into the sub-micron range.

    Science.gov (United States)

    Cytometry Part A Special Section: Separating the signal from the noise: Expanding flow cytometry into the sub-micron range. The current Cytometry Part A Special Section presents three studies that utilize cytometers to study sub-micron particles. The three studies involve the 1...

  18. Economic Dispatch Thermal Generator Using Modified Improved Particle Swarm Optimization

    Directory of Open Access Journals (Sweden)

    M. Natsir Rahman

    2012-09-01

    Full Text Available Fuel cost of a thermal generator is its own load functions. In this research, Modified Improved Particle Swarm Optimization (MIPSO is applied to calculate economic dispatch. Constriction Factor Approach (CFA is used to modify IPSO algorithm because of the advantage to improve the ability of global searching and avoid local minimum so that the time needed to converge become faster. Simulation results achieved by using  MIPSO method at the time of peak load of of 9602 MW, obtained generation cost is Rp 7,366,912,798,34 per hour, while generation cost of real system is Rp. 7,724,012,070.30 per hour. From the simulation result can be concluded that MIPSO can reduce the generation cost of  500 kV Jawa Bali transmission system of Rp 357,099,271.96 per hour or equal to 4,64%.

  19. Light absorption properties of laboratory generated tar ball particles

    Science.gov (United States)

    Hoffer, A.; Tóth, A.; Nyirő-Kósa, I.; Pósfai, M.; Gelencsér, A.

    2015-06-01

    Tar balls (TBs) are a specific particle type which is abundant in the global troposphere, in particular in biomass smoke plumes. These particles belong to the family of atmospheric brown carbon (BrC) which can absorb light in the visible range of the solar spectrum. Albeit TBs are typically present as individual particles in biomass smoke plumes, their absorption properties have been only indirectly inferred from field observations or calculations based on their electron energy-loss spectra. This is because in biomass smoke TBs coexist with various other particle types (e.g. organic particles with inorganic inclusions and soot, the latter is emitted mainly during flaming conditions) from which they cannot be physically separated; thus, a direct experimental determination of their absorption properties is not feasible. Very recently we have demonstrated that TBs can be generated in the laboratory from droplets of wood tar that resemble atmospheric TBs in all of their observed properties. As a follow-up study we have installed on-line instruments to our laboratory set-up generating pure TB particles to measure the absorption and scattering, as well as size distribution of the particles. In addition, samples were collected for transmission electron microscopy (TEM) and total carbon (TC) analysis. The effects of experimental parameters were also studied. The mass absorption coefficients of the laboratory generated TBs were found to be in the range of 0.8-3.0 m2 g-1 at 550 nm, with absorption Ångström exponents (AAE) between 2.7 and 3.4 (average 2.9) in the wavelength range 467-652 nm. The refractive index of TBs as derived from Mie calculations was about 1.84-0.21i at 550 nm. In the brown carbon continuum these values fall closer to those of soot than to other light-absorbing species such as humic-like substances (HULIS). Considering the abundance of TBs in biomass smoke and the global magnitude of biomass burning emissions, these findings may have substantial

  20. Light absorption properties of laboratory-generated tar ball particles

    Directory of Open Access Journals (Sweden)

    A. Hoffer

    2016-01-01

    Full Text Available Tar balls (TBs are a specific particle type that is abundant in the global troposphere, in particular in biomass smoke plumes. These particles belong to the family of atmospheric brown carbon (BrC, which can absorb light in the visible range of the solar spectrum. Albeit TBs are typically present as individual particles in biomass smoke plumes, their absorption properties have been only indirectly inferred from field observations or calculations based on their electron energy-loss spectra. This is because in biomass smoke TBs coexist with various other particle types (e.g., organic particles with inorganic inclusions and soot, the latter emitted mainly during flaming conditions from which they cannot be physically separated; thus, a direct experimental determination of their absorption properties is not feasible. Very recently we have demonstrated that TBs can be generated in the laboratory from droplets of wood tar that resemble atmospheric TBs in all of their observed properties. As a follow-up study, we have installed on-line instruments to our laboratory set-up, which generate pure TB particles to measure the absorption and scattering, as well as the size distribution of the particles. In addition, samples were collected for transmission electron microscopy (TEM and total carbon (TC analysis. The effects of experimental parameters were also studied. The mass absorption coefficients of the laboratory-generated TBs were found to be in the range of 0.8–3.0 m2 g−1 at 550 nm, with absorption Ångström exponents (AAE between 2.7 and 3.4 (average 2.9 in the wavelength range 467–652 nm. The refractive index of TBs as derived from Mie calculations was about 1.84 − 0.21i at 550 nm. In the brown carbon continuum, these values fall closer to those of soot than to other light-absorbing species such as humic-like substances (HULIS. Considering the abundance of TBs in biomass smoke and the global magnitude of biomass burning

  1. Electric energy production by particle thermionic-thermoelectric power generators

    Science.gov (United States)

    Oettinger, P. E.

    1980-01-01

    Thermionic-thermoelectric power generators, composed of a thin layer of porous, low work function material separating a heated emitter electrode and a cooler collector electrode, have extremely large Seebeck coefficients of over 2 mV/K and can provide significant output power. Preliminary experiments with 20-micron thick (Ba Sr Ca)O coatings, limited by evaporative loss to temperatures below 1400 K, have yielded short circuit current densities of 500 mA/sq cm and power densities of 60 mW/ sq cm. Substantially more output is expected with cesium-coated refractory oxide particle coatings operating at higher temperatures. Practical generators will have thermal-to-electrical efficiencies of 10 to 20%. Further increases can be gained by cascading these high-temperature devices with lower temperature conventional thermoelectric generators.

  2. Disruption of Particle Detector Electronics by Beam Generated EMI

    Energy Technology Data Exchange (ETDEWEB)

    Bower, G.; /SLAC; Sugimoto, Y.; /KEK, Tsukuba; Sinev, N.; /Oregon U.; Arnold, R.; Woods, M.; /SLAC

    2007-06-27

    The possibility that radio frequency beam generated electromagnetic interference (EMI) could disrupt the operation of particle detector electronics has been of some concern since the inception of short pulse electron colliders more than 30 years ago [1]. Some instances have been reported where this may have occurred but convincing evidence has not been available. This possibility is of concern for the International Linear Collider (ILC). We have conducted test beam studies demonstrating that electronics disruption does occur using the vertex detector electronics (VXD) from the SLD detector which took data at the SLC at SLAC. We present the results of those tests, and we describe the need for EMI standards for beam and detector instrumentation in the IR region at the ILC.

  3. A Novel Inlet System for On-line Chemical Analysis of Semi-Volatile Submicron Particulate Matter

    Science.gov (United States)

    Wisthaler, A.; Eichler, P.; Müller, M.; D'anna, B.

    2014-12-01

    We herein present the concept of a novel modular inlet system that allows using gas-phase analyzers for on-line chemical characterization of semi-volatile submicron particles. The "Chemical analysis of aerosol on-line" (CHARON) inlet consists of a gas-phase denuder for stripping off gas-phase analytes, an aerodynamic lens for particle enrichment in the sampling flow and a thermo-desorption unit for particle volatilization prior to chemical analysis. We coupled the CHARON inlet to a proton-transfer-reaction time-of-flight mass spectrometer (PTR-ToF-MS) which quantitatively detects most organic analytes and ammonia. The combined set-up measures submicron organic and ammonium nitrate/sulfate particles online. Proof-of-principle studies were carried out for demonstrating the analytical power of the new set-up in analyzing primarily emitted and secondarily generated particles. A promising future application is the study of the partitioning of organic compounds between the gas and the particulate phase.

  4. Encouragement of Enzyme Reaction Utilizing Heat Generation from Ferromagnetic Particles Subjected to an AC Magnetic Field.

    Directory of Open Access Journals (Sweden)

    Masashi Suzuki

    Full Text Available We propose a method of activating an enzyme utilizing heat generation from ferromagnetic particles under an ac magnetic field. We immobilize α-amylase on the surface of ferromagnetic particles and analyze its activity. We find that when α-amylase/ferromagnetic particle hybrids, that is, ferromagnetic particles, on which α-amylase molecules are immobilized, are subjected to an ac magnetic field, the particles generate heat and as a result, α-amylase on the particles is heated up and activated. We next prepare a solution, in which α-amylase/ferromagnetic particle hybrids and free, nonimmobilized chitinase are dispersed, and analyze their activities. We find that when the solution is subjected to an ac magnetic field, the activity of α-amylase immobilized on the particles increases, whereas that of free chitinase hardly changes; in other words, only α-amylase immobilized on the particles is selectively activated due to heat generation from the particles.

  5. Zirconia nanocrystals as submicron level biological label

    Science.gov (United States)

    Smits, K.; Liepins, J.; Gavare, M.; Patmalnieks, A.; Gruduls, A.; Jankovica, D.

    2012-08-01

    Inorganic nanocrystals are of increasing interest for their usage in biology and pharmacology research. Our interest was to justify ZrO2 nanocrystal usage as submicron level biological label in baker's yeast Saccharomyces cerevisia culture. For the first time (to our knowledge) images with sub micro up-conversion luminescent particles in biologic media were made. A set of undoped as well as Er and Yb doped ZrO2 samples at different concentrations were prepared by sol-gel method. The up-conversion luminescence for free standing and for nanocrystals with baker's yeast cells was studied and the differences in up-conversion luminescence spectra were analyzed. In vivo toxic effects of ZrO2 nanocrystals were tested by co-cultivation with baker's yeast.

  6. Submicron magnetic core conducting polypyrrole polymer shell: Preparation and characterization.

    Science.gov (United States)

    Tenório-Neto, Ernandes Taveira; Baraket, Abdoullatif; Kabbaj, Dounia; Zine, Nadia; Errachid, Abdelhamid; Fessi, Hatem; Kunita, Marcos Hiroiuqui; Elaissari, Abdelhamid

    2016-04-01

    Magnetic particles are of great interest in various biomedical applications, such as, sample preparation, in vitro biomedical diagnosis, and both in vivo diagnosis and therapy. For in vitro applications and especially in labs-on-a-chip, microfluidics, microsystems, or biosensors, the needed magnetic dispersion should answer various criteria, for instance, submicron size in order to avoid a rapid sedimentation rate, fast separations under an applied magnetic field, and appreciable colloidal stability (stable dispersion under shearing process). Then, the aim of this work was to prepare highly magnetic particles with a magnetic core and conducting polymer shell particles in order to be used not only as a carrier, but also for the in vitro detection step. The prepared magnetic seed dispersions were functionalized using pyrrole and pyrrole-2-carboxylic acid. The obtained core-shell particles were characterized in terms of particle size, size distribution, magnetization properties, FTIR analysis, surface morphology, chemical composition, and finally, the conducting property of those particles were evaluated by cyclic voltammetry. The obtained functional submicron highly magnetic particles are found to be conducting material bearing function carboxylic group on the surface. These promising conducting magnetic particles can be used for both transport and lab-on-a-chip detection. Copyright © 2015. Published by Elsevier B.V.

  7. Nanoparticle production by UV irradiation of combustion generated soot particles

    Energy Technology Data Exchange (ETDEWEB)

    Stipe, Christopher B.; Choi, Jong Hyun; Lucas, Donald; Koshland, Catherine P.; Sawyer, Robert F.

    2004-07-01

    Laser ablation of surfaces normally produce high temperature plasmas that are difficult to control. By irradiating small particles in the gas phase, we can better control the size and concentration of the resulting particles when different materials are photofragmented. Here, we irradiate soot with 193 nm light from an ArF excimer laser. Irradiating the original agglomerated particles at fluences ranging from 0.07 to 0.26 J/cm{sup 2} with repetition rates of 20 and 100 Hz produces a large number of small, unagglomerated particles, and a smaller number of spherical agglomerated particles. Mean particle diameters from 20 to 50 nm are produced from soot originally having a mean electric mobility diameter of 265nm. We use a non-dimensional parameter, called the photon/atom ratio (PAR), to aid in understanding the photofragmentation process. This parameter is the ratio of the number of photons striking the soot particles to the number of the carbon atoms contained in the soot particles, and is a better metric than the laser fluence for analyzing laser-particle interactions. These results suggest that UV photofragmentation can be effective in controlling particle size and morphology, and can be a useful diagnostic for studying elements of the laser ablation process.

  8. Size distributions of particles and their generating mechanisms

    DEFF Research Database (Denmark)

    Barndorff-Nielsen, Ole Eiler

    Summary of a lecture presented at the IAHR Workshop on Particle Motion and Sediment Transport: Measurement Techniques and Experimental Results, Schweiz, 5-8 April 1981......Summary of a lecture presented at the IAHR Workshop on Particle Motion and Sediment Transport: Measurement Techniques and Experimental Results, Schweiz, 5-8 April 1981...

  9. Deposition of Flame-generated Al2O3 Nano-particles on a Porous Surface

    DEFF Research Database (Denmark)

    Andersen, Sune Klint; Johannessen, Jens Tue; Wedel, Stig

    1998-01-01

    When particles of catalytic materials become less than 50 nm they start toexhibit a stronger catalytic activity compared to their bulk counterparts. Nano-particles are thus good candidates for manufacture of highly activecatalysts. Nanometer sized particles of catalytic materials may be generated...... athigh temperatures in flames. The direct deposition from gas phase on a ceramicsubstrate tube of flame-generated particles leads to a uniform, porous layer ofsmall particles, masking the coarser structure of the substrate tube. The methodlooks promising for manufacture of catalytic filters and membranes....

  10. Effect of indoor-generated airborne particles on radon progeny dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Trassierra, C. Vargas [Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, Cassino, FR (Italy); Stabile, L., E-mail: l.stabile@unicas.it [Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, Cassino, FR (Italy); Cardellini, F.; Morawska, L. [National Institute of Ionizing Radiation Metrology (INMRI-ENEA), Rome (Italy); Buonanno, G. [Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, Cassino, FR (Italy); International Laboratory for Air Quality and Health, Queensland University of Technology, Brisbane (Australia)

    2016-08-15

    Highlights: • Investigation of the interaction between particles and radon progeny dynamics. • Measurements of particles emitted by different indoor sources. • Tests performed in a controlled radon chamber. • Particle size strongly influences the radon progeny dynamics. • Particle surface area concentration is the key parameter of the radon-particle interaction. - Abstract: In order to investigate the interaction between radon progeny and particles, an experimental campaign was carried out in a radon chamber at the Italian National Institute of Ionizing Radiation Metrology, quantifying the amount of attached and unattached radon daughters present in air, as well as the equilibrium factor in the presence of particles generated through indoor sources. A fixed radon concentration was maintained, while particles were generated using incense sticks, mosquito coils and gas combustion. Aerosols were characterized in terms of particle concentrations and size distributions. Simultaneously, radon concentration and attached/unattached potential alpha energy concentration in the air were continuously monitored by two different devices, based on alpha spectroscopy techniques. The presence of particles was found to affect the attached fraction of radon decay products, in such a way that the particles acted as a sink for radionuclides. In terms of sources which emit large particles (e.g. incense, mosquito coils), which greatly increase particle surface area concentrations, the Equilibrium Factor was found to double with respect to the background level before particle generation sessions. On the contrary, the radon decay product dynamics were not influenced by gas combustion processes, mainly due to the small surface area of the particles emitted.

  11. Thermal fragmentation and deactivation of combustion-generated soot particles

    KAUST Repository

    Raj, Abhijeet

    2014-09-01

    The effect of thermal treatment on diesel soot and on a commercial soot in an inert environment under isothermal conditions at intermediate temperatures (400-900°C) is studied. Two important phenomena are observed in both the soot samples: soot fragmentation leading to its mass loss, and loss of soot reactivity towards O2. Several experimental techniques such as high resolution transmission electron microscopy, electron energy loss spectroscopy, thermo-gravimetric analysis with mass spectrometry, elemental analysis, Fourier transform infrared spectroscopy and X-ray diffraction have been used to identify the changes in structures, functional groups such as oxygenates and aliphatics, σ and π bonding, O/C and H/C ratios, and crystallite parameters of soot particles, introduced by heat. A decrease in the size of primary particles and an increase in the average polycyclic aromatic hydrocarbon (PAH) size was observed in soots after thermal treatment. The activation energies of soot oxidation for thermally treated soot samples were found to be higher than those for the untreated ones at most conversion levels. The cyclic or acyclic aliphatics with sp3 hybridization were present in significant amounts in all the soot samples, but their concentration decreased with thermal treatment. Interestingly, the H/C and the O/C ratios of soot particles increased after thermal treatment, and thus, they do not support the decrease in soot reactivity. The increase in the concentration of oxygenates on soot surface indicate that their desorption from soot surface in the form of CO, CO2 and other oxygenated compounds may not be significant at the temperatures (400-900°C) studied in this work. © 2014 The Combustion Institute.

  12. Changes of propagation light in optical fiber submicron wires

    Science.gov (United States)

    Stasiewicz, K. A.; Łukowski, A.; Jaroszewicz, L. R.

    2013-05-01

    At the moment technology allows to miniaturize measurement system to several micrometers. Application of an optical fiber taper in such system needs to manufacture a new one with diameters below single micrometers which is very difficult and expensive. Another way to obtain this level of diameters is the process of tapering from the existing fibers. In the paper, experimental results of propagation light from a supercontinnum sources of the wavelength generates the wavelength of 350-2000 nm, in different optical fiber submicron wires made from tapers manufactured from single mode fibers are presented. Biconical optical fibers' tapers were manufactured in low pressure gas burner technique. There are presented spectral characteristics of a propagated beam. For the test, there was manufactured an optical fiber submicron wires with a different length of waist region with a diameter near one micrometer. We put to the test a taper made from a standard telecommunication fiber SMF-28 with a cutoff wavelength equal to 1260.

  13. Oxidative stress generated damage to DNA by gastrointestinal exposure to insoluble particles

    DEFF Research Database (Denmark)

    Møller, Peter; Folkmann, J K; Danielsen, P H

    2012-01-01

    There is growing concern that gastrointestinal exposure to particles is associated with increased risk of toxicity to internal organs and carcinogenicity. The mechanism of action is related to particle-induced oxidative stress and oxidation of DNA. Observations from animal models indicate...... that gastrointestinal exposure to single-walled carbon nanotubes (SWCNT), fullerenes C60, carbon black, titanium dioxide and diesel exhaust particles generates oxidized DNA base lesions in organs such as the bone marrow, liver and lung. Oral exposure to nanosized carbon black has also been associated with increased...... level of lipid peroxidation derived exocyclic DNA adducts in the liver, suggesting multiple pathways of oxidative stress for particle-generated damage to DNA. At equal dose, diesel exhaust particles (SRM2975) generated larger levels of 8-oxo-7,8-dihydro-2'-deoxyguanosine in rat liver than carbon black...

  14. Formation and behaviour of dust particle clouds in a radio-frequency discharge: results in the laboratory and under microgravity conditions

    Energy Technology Data Exchange (ETDEWEB)

    Mikikian, M [Groupe de Recherches sur l' Energetique des Milieux Ionises, Universite d' Orleans, 45067 Orleans Cedex 2 (France); Boufendi, L [Groupe de Recherches sur l' Energetique des Milieux Ionises, Universite d' Orleans, 45067 Orleans Cedex 2 (France); Bouchoule, A [Groupe de Recherches sur l' Energetique des Milieux Ionises, Universite d' Orleans, 45067 Orleans Cedex 2 (France); Thomas, H M [Max-Planck-Institut fuer Extraterrestrische Physik, 85741 Garching (Germany); Morfill, G E [Max-Planck-Institut fuer Extraterrestrische Physik, 85741 Garching (Germany); Nefedov, A P [Institute for High Energy Densities, Izhorskaya 13/19, Moscow, 127412 (Russian Federation); Fortov, V E [Institute for High Energy Densities, Izhorskaya 13/19, Moscow, 127412 (Russian Federation)

    2003-03-01

    In this paper we report the first observation on submicron dust particle clouds grown in a radio-frequency sputtering discharge under microgravity conditions. These results have been obtained in the PKE-Nefedov (Plasma Kristall Experiment) chamber in the framework of a French-German-Russian programme. A dust-free region, usually called the 'void', is observed in the laboratory and under microgravity conditions even with submicron particles. In this region, successive generations of particles can be grown, leading to the coexistence of particles with various sizes. Each generation of particles constitutes a cloud separated from the others by a definite sheath. Dynamics of these clouds have been investigated showing vortex-like motions or independent behaviour of small heaps of particles, emphasizing both attractive and repulsive effects between dust clouds. As these particles drastically influence the plasma properties, the growth kinetics is followed through the evolution of the discharge current.

  15. Physicochemical and toxicological characteristics of welding fume derived particles generated from real time welding processes.

    Science.gov (United States)

    Chang, Cali; Demokritou, Philip; Shafer, Martin; Christiani, David

    2013-01-01

    Welding fume particles have been well studied in the past; however, most studies have examined welding fumes generated from machine models rather than actual exposures. Furthermore, the link between physicochemical and toxicological properties of welding fume particles has not been well understood. This study aims to investigate the physicochemical properties of particles derived during real time welding processes generated during actual welding processes and to assess the particle size specific toxicological properties. A compact cascade impactor (Harvard CCI) was stationed within the welding booth to sample particles by size. Size fractionated particles were extracted and used for both off-line physicochemical analysis and in vitro cellular toxicological characterization. Each size fraction was analyzed for ions, elemental compositions, and mass concentration. Furthermore, real time optical particle monitors (DustTrak™, TSI Inc., Shoreview, Minn.) were used in the same welding booth to collect real time PM2.5 particle number concentration data. The sampled particles were extracted from the polyurethane foam (PUF) impaction substrates using a previously developed and validated protocol, and used in a cellular assay to assess oxidative stress. By mass, welding aerosols were found to be in coarse (PM 2.5–10), and fine (PM 0.1–2.5) size ranges. Most of the water soluble (WS) metals presented higher concentrations in the coarse size range with some exceptions such as sodium, which presented elevated concentration in the PM 0.1 size range. In vitro data showed size specific dependency, with the fine and ultrafine size ranges having the highest reactive oxygen species (ROS) activity. Additionally, this study suggests a possible correlation between welders' experience, the welding procedure and equipment used and particles generated from welding fumes. Mass concentrations and total metal and water soluble metal concentrations of welding fume particles may be

  16. Characteristics of Submicron Aerosols in 2013 summer of Beijing

    Science.gov (United States)

    Guo, Song; Hu, Min; Shang, Dongjie; Zheng, Jing; Du, Zhuofei; Wu, Yusheng; Lu, Sihua; Zeng, Limin; Zhang, Renyi

    2016-04-01

    To characterize the air pollution of North China Plain of China, CAREBEIJING-2013 field campaign (Campaigns of Air quality REsearch in BEIJING and surrounding region) was conducted in summer of 2013. Submicron aerosols were measured at an urban site PKU (Peking University, 39° 59'21"N, 116° 18'25"E) from July 28th to September 31st 2013. A suite of integrated instruments was used to measure the size distribution, effective density and hygroscopicity of ambient particles. The chemical composition of submicron particles were measured by using an Aerodyne High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS) (Billerica, MA, USA). The average PM2.5 concentration was 73.0±70.7 μg m-3 during the measurement. The particulate pollution showed distinct 4-7 days cycles controlled by the meteorological conditions. Each cycle started with low PM2.5 mass concentrations (air mass was from relatively clean mountainous area. The particle number concentrations were high, but and the sizes were small (60 μg day-1, and the particle mean diameter grew to >100 nm. It is interesting to note that the mean diameters showed similar trend to PM2.5 mass concentrations, indicating the particle pollution attributed to the growth of the newly formed small particles. During the measurement, the average particle densities are between 1.3-1.5 g cm-3, indicating organics and sulfate were dominant in the particles. The densities of smaller particles, i.e. 46 nm, 81nm, showed single peak at 1.3-1.5 g cm-3, indicating the particles are internal mixed sulfate and organics. While the 150nm and 240 nm particle densities exhibited bimodal distribution with an additional small peak at ˜1.1 g cm-3, which is considered as external mixed organic particles or aged soot particles. The particle hygroscopic growth factor for all the measured sizes at RH of 90% showed bimodal distribution, attributing to external mixed organics (or aged soot) and internal mixed organics and sulfate. Both the

  17. Rotation invariance of electromagnetic radiation generated by relativistic particles in magnetic fields

    CERN Document Server

    Smolyakov, M N

    2000-01-01

    This paper deals with electromagnetic radiation generated by relativistic particles in arbitrary planar magnetic field (in undulator for example). Magnetic system producing this field is assumed to be planar consisting of permanent magnets. It is shown that there is a special class of magnetic moment rotations in such system while magnetic field is varying but spontaneous radiation spectrum generated by relativistic particles remains the same. This property of electromagnetic radiation can be used in designing new undulators.

  18. 3-D Synthetic Microstructure Generation with Ellipsoid Particles

    Science.gov (United States)

    2016-09-27

    for public release; distribution is unlimited. 6. References 1. Torquato S. Random heterogeneous materials: microstructures and macro - scopic...ellipse parameters to Excel % Store all ellipse parameters in Excel so that the 3D structure % can be generated without worrying about overlap...created by: Quan Quach % date: 11/6/07 % this function erases any empty sheets in an excel document function deleteEmptyExcelSheets(fileName) % the input

  19. A non-perturbative mechanism for elementary particle mass generation

    CERN Document Server

    Frezzotti, R

    2014-01-01

    Taking inspiration from lattice QCD data, we argue that a finite non-perturbative mass contribution for quarks is generated as a consequence of the dynamical phenomenon of spontaneous chiral symmetry breaking, in turn triggered by the explicitly breaking of chiral symmetry induced by the critical Wilson term in the action. In pure lattice QCD this mass term cannot be separated from the unavoidably associated linearly divergent contribution. However, if QCD is enlarged to a theory where also a scalar field is present, coupled to a doublet of SU(2) fermions via a Yukawa and a Wilson-like term, then in the phase where the scalar field takes a non-vanishing expectation value, a dynamically generated and "naturally" light fermion mass (numerically unrelated to the expectation value of the scalar field) is conjectured to emerge at a critical value of the Yukawa coupling where the symmetry of the model is maximally enhanced. Masses dynamically generated in this way display a natural hierarchy according to which the ...

  20. Electron acceleration via high contrast laser interacting with submicron clusters

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Lu; Chen Liming; Wang Weiming; Yan Wenchao; Yuan Dawei; Mao Jingyi; Wang Zhaohua; Liu Cheng; Shen Zhongwei; Li Yutong; Dong Quanli; Lu Xin; Ma Jinglong; Wei Zhiyi [Beijing National Laboratory of Condensed Matter Physics, Institute of Physics, CAS, Beijing 100080 (China); Faenov, Anatoly; Pikuz, Tatiana [Joint Institute for High Temperature of the Russian Academy of Sciences, Izhorskaya 13/19, Moscow 127412 (Russian Federation); Quantum Beams Science Directorate, JAEA, Kizugawa, Kyoto (Japan); Li Dazhang [Beijing National Laboratory of Condensed Matter Physics, Institute of Physics, CAS, Beijing 100080 (China); Institute of High Energy Physics, CAS, Beijing 100049 (China); Sheng Zhengming [Department of Physics, Shanghai Jiao Tong University, Shanghai 200240 (China); Zhang Jie [Beijing National Laboratory of Condensed Matter Physics, Institute of Physics, CAS, Beijing 100080 (China); Department of Physics, Shanghai Jiao Tong University, Shanghai 200240 (China)

    2012-01-02

    We experimentally investigated electron acceleration from submicron size argon clusters-gas target irradiated by a 100 fs, 10 TW laser pulses having a high-contrast. Electron beams are observed in the longitudinal and transverse directions to the laser propagation. The measured energy of the longitudinal electron reaches 600 MeV and the charge of the electron beam in the transverse direction is more than 3 nC. A two-dimensional particle-in-cell simulation of the interaction has been performed and it shows an enhancement of electron charge by using the cluster-gas target.

  1. Effects of an ozone-generating air purifier on indoor secondary particles in three residential dwellings.

    Science.gov (United States)

    Hubbard, H F; Coleman, B K; Sarwar, G; Corsi, R L

    2005-12-01

    The use of indoor ozone generators as air purifiers has steadily increased over the past decade. Many ozone generators are marketed to consumers for their ability to eliminate odors and microbial agents and to improve health. In addition to the harmful effects of ozone, recent studies have shown that heterogeneous and homogeneous reactions between ozone and some unsaturated hydrocarbons can be an important source of indoor secondary pollutants, including free radicals, carbonyls, carboxylic acids, and fine particles. Experiments were conducted in one apartment and two detached single-family dwellings in Austin, TX, to assess the effects of an ozone generator on indoor secondary organic aerosol concentrations in actual residential settings. Ozone was generated using a commercial ozone generator marketed as an air purifier, and particle measurements were recorded before, during, and after the release of terpenes from a pine oil-based cleaning product. Particle number concentration, ozone concentration, and air exchange rate were measured during each experiment. Particle number and mass concentrations increased when both terpenes and ozone were present at elevated levels. Experimental results indicate that ozone generators in the presence of terpene sources facilitate the growth of indoor fine particles in residential indoor atmospheres. Human exposure to secondary organic particles can be reduced by minimizing the intentional release of ozone, particularly in the presence of terpene sources. Past studies have shown that ozone-initiated indoor chemistry can lead to elevated concentrations of fine particulate matter, but have generally been completed in controlled laboratory environments and office buildings. We explored the effects of an explicit ozone generator marketed as an air purifier on the formation of secondary organic aerosol mass in actual residential indoor settings. Results indicate significant increases in number and mass concentrations for particles

  2. The surface characterisation and comparison of two potential sub-micron, sugar bulking excipients for use in low-dose, suspension formulations in metered dose inhalers.

    Science.gov (United States)

    James, Jeff; Crean, Barry; Davies, Martyn; Toon, Richard; Jinks, Phil; Roberts, Clive J

    2008-09-01

    This study compares the surface characteristics and surface energetics of two potential bulking excipients, anhydrous sub-micron alpha-lactose and sub-micron sucrose, for use with low-dose, suspension formulations in pressurised metered dose inhalers (pMDIs). Both sub-micron bulking excipients are processed from parent materials (alpha-lactose monohydrate/alpha-lactose monohydrate and silk grade sucrose, respectively) so the surface characteristics of each material were determined and compared. Additionally, the surface energetics and adhesive interactions between each sub-micron bulking excipient and some chosen active pharmaceutical ingredients (APIs) used in pMDI formulations were also determined. From this data, it was possible to predict the potential degree of interaction between the APIs and each sub-micron bulking excipient, thus determining suitable API-excipient combinations for pMDI formulation optimisation. Salmon calcitonin was also investigated as a potential API due to the current interest in, and the potential low-dose requirements for, the pulmonary delivery of proteins. The size and morphology of each sub-micron excipient (and parent materials) were determined using scanning electron microscopy (SEM) and the crystalline nature of each sub-micron excipient and parent material was assessed using X-ray diffraction (XRD). The surface chemistry of each sub-micron excipient was analysed using X-ray photoelectron spectroscopy (XPS). The surface energies of each sub-micron excipient, along with their respective parent materials and any intermediates, were determined using two techniques. The surface energies of these materials were determined via (a) single particle adhesive interactions using atomic force microscopy (AFM) and (b) 'bulk' material surface interactions using contact angle measurements (CA). From the CA data, it was possible to calculate the theoretical work of adhesion values for each API-excipient interaction using the surface component

  3. Development of a Zero-Dimensional Particle Generation Model in SFR-Containments under Accidental Conditions

    Energy Technology Data Exchange (ETDEWEB)

    García, M.; Herranz, L.E.

    2015-07-01

    During postulated Beyond Design Basis Accidents (BDBAs) in Sodium-cooled Fast Reactors (SFRs), contaminated-sodium at high temperature may leak into the containment and burns in the presence of oxygen. As a result, large quantities of sodium oxide aerosols are produced. In the frame of the EU-JASMIN project, a particle generation model to calculate the particle generation rate and their primary size during a generic sodium pool fire has been developed to be implemented in ASTEC-Na code. This paper presents the adaptation of the 3-D particle generation model to a 0-D model based on the generation of particles under average system conditions. Deviations between both approaches less than 20% have been found in all the simulated scenarios. From the 0-D model, simple correlations for the particle generation rate and the primary particle size as a function of Na-oxide vapour pressures, temperature and sodium pool characteristics have been derived for its straightforward implementation in the ASTEC-Na code. (Author)

  4. Entropy generation during the quasi-steady burning of spherical fuel particles

    Energy Technology Data Exchange (ETDEWEB)

    Raghavan, V.; Gogos, G. [Department of Mechanical Engineering, University of Nebraska-Lincoln, Lincoln, NE 68588 (United States); Babu, V.; Sundararajan, T. [Department of Mechanical Engineering, Indian Institute of Technology Madras, Chennai 600036 (India)

    2007-06-15

    Entropy generation during the quasi-steady combustion of spherical liquid fuel particles has been presented in detail. The effects of freestream velocity, particle diameter, ambient temperature and gravity, on the entropy generation rate, have been discussed in detail. In the range of sub-critical freestream velocity, where an envelope flame is present, the entropy generation rate presents a minimum value. At a critical velocity, where the flame transition occurs, the entropy generation rate reaches a maximum value. Flame transition significantly affects the entropy generation rate, which suffers a sharp decrease in its value after the transition. Heat transfer and chemical reaction contribute almost equally to the total entropy generation rate. When normal gravity is considered in an upward flow configuration, there is an increase in the entropy generation rate as compared to the zero gravity case. The effect of gravity poses a complex variation pattern in the entropy generation rate, for a downward flow configuration. The entropy generation rate decreases with increasing ambient temperature. The entropy generation rate increases with the particle diameter. A correlation has been presented for the non-dimensional entropy generation number as a function of Froude number. (author)

  5. Automatically Generating Questions to Support the Acquisition of Particle Verbs: Evaluating via Crowdsourcing

    Science.gov (United States)

    Chinkina, Maria; Ruiz, Simón; Meurers, Detmar

    2017-01-01

    We integrate insights from research in Second Language Acquisition (SLA) and Computational Linguistics (CL) to generate text-based questions. We discuss the generation of wh- questions as functionally-driven input enhancement facilitating the acquisition of particle verbs and report the results of two crowdsourcing studies. The first study shows…

  6. Microfluidic generation of particle-stabilized water-in-water emulsions

    Science.gov (United States)

    Abbasi, Niki; Navi, Maryam; Tsai, Scott

    2017-11-01

    We present a microfluidic platform that generates particle-stabilized water-in-water emulsions, using an aqueous two-phase system (ATPS) of polyethylene glycol (PEG) and Dextran (DEX). DEX droplets are generated passively at a flow focusing junction, in a continuous phase of PEG and carboxylated particles, using weak hydrostatic pressure to drive the flow. As DEX droplets travel inside the microfluidic device, carboxylated particles partition to the interface of the droplets. The number of particles partitioning to the interface of droplets increases as the droplets migrate downstream in the microchannel. As a result, the DEX droplets become stabilized against coalescence. We study the coverage and stability of the DEX droplets further downstream inside a reservoir, by changing the carboxylated particle concentration and the particle size. We anticipate that particle-stabilized water-in-water emulsions may have important biotechnological applications, due to their intrinsic biocompatibility compared to traditional particle-stabilized water-in-oil emulsions, for example for cell encapsulation.

  7. Laser and Particle Guiding Micro-Elements for Particle Accelerators

    CERN Document Server

    Plettner, Tomas; Spencer, James; Wisdom, Jeffrey

    2005-01-01

    Laser driven particle accelerators based on the current generation of lasers will require sub-micron control of the laser field as well as precise beam guiding. Hence the fabrication techniques that allow integrating both elements into an accelerator-on-chip format become critical for the success of such particle accelerators. Micromachining technology for silicon has been shown to be one such feasible technology in PAC2003 but with a variety of complications on the laser side. Fortunately, in recent years the fabrication of transparent ceramics has become an interesting technology that could be applied for laser-particle accelerators in several ways. We discuss this area, its advantages such as the range of materials it provides and various ways to implement it followed by some different test examples that have been considered. One important goal of this approach is an integrated system that could avoid the necessity of having to inject either laser or particle pulses into these structures.

  8. Role of particle masses in the magnetic field generation driven by the parity violating interaction

    Directory of Open Access Journals (Sweden)

    Maxim Dvornikov

    2016-09-01

    Full Text Available Recently the new model for the generation of strong large scale magnetic fields in neutron stars, driven by the parity violating interaction, was proposed. In this model, the magnetic field instability results from the modification of the chiral magnetic effect in presence of the electroweak interaction between ultrarelativistic electrons and nucleons. In the present work we study how a nonzero mass of charged particles, which are degenerate relativistic electrons and nonrelativistic protons, influences the generation of the magnetic field in frames of this approach. For this purpose we calculate the induced electric current of these charged particles, electroweakly interacting with background neutrons and an external magnetic field, exactly accounting for the particle mass. This current is calculated by two methods: using the exact solution of the Dirac equation for a charged particle in external fields and computing the polarization operator of a photon in matter composed of background neutrons. We show that the induced current is vanishing in both approaches leading to the zero contribution of massive particles to the generated magnetic field. We discuss the implication of our results for the problem of the magnetic field generation in compact stars.

  9. Magnetic Field Generation through Angular Momentum Exchange between Circularly Polarized Radiation and Charged Particles

    Energy Technology Data Exchange (ETDEWEB)

    G. Shvets; N.J. Fisch; J.-M. Rax

    2002-01-18

    The interaction between circularly polarized (CP) radiation and charged particles can lead to generation of magnetic field through an inverse Faraday effect. The spin of the circularly polarized electromagnetic wave can be converted into the angular momentum of the charged particles so long as there is dissipation. We demonstrate this by considering two mechanisms of angular momentum absorption relevant for laser-plasma interactions: electron-ion collisions and ionization. The precise dissipative mechanism, however, plays a role in determining the efficiency of the magnetic field generation.

  10. Performance of a new generation RPCs for particle physics at colliders of the next generation

    CERN Document Server

    Paolozzi, L; The ATLAS collaboration

    2013-01-01

    The upgrade of present and future experiments in particle physics at high luminosity colliders will require a level one trigger of high selectivity and robustness in order to cope with the very heavy background levels. This selectivity requires detectors with very good space and time resolution operating at high rate. We present in this paper the latest developments of the RPC detectors concerning rate capability (up to 30kHz/cm2), space resolution (few hundred microns) and time resolution (few hundred pico s). We also show that this improvement required the development of a fast, low noise and large dynamics front end electronics and a better understanding of the detector physics.

  11. Enhancement in electrical conductivity of pastes containing submicron Ag-coated Cu filler with palmitic acid surface modification

    Science.gov (United States)

    Choi, Eun Byeol; Lee, Jong-Hyun

    2017-09-01

    The fabrication and applied use of submicron Ag-coated Cu (Cu@Ag) particles as a filler material for epoxy-based conductive pastes having the advantages of a lower material cost and antioxidation behavior were studied. Submicron Cu@Ag particles were successfully prepared and surface-modified using palmitic acid. Diffuse reflectance infrared Fourier transform spectroscopy and thermogravimetric differential scanning calorimetry results indicated the formation of an organic layer by the chemical interaction between the Cu@Ag surface and palmitic acid and the survival of the organic layer after treatment at 160 °C for 3 h in air. The printed pastes containing both commercial micron Cu@Ag flakes and the fabricated submicron Cu@Ag particles showed a greatly reduced electrical resistivity (4.68 × 10-4 Ω cm) after surface modification compared to an initial value of 1.85 × 10-3 Ω cm when cured.

  12. Oxidative stress and inflammation generated DNA damage by exposure to air pollution particles

    DEFF Research Database (Denmark)

    Møller, Peter; Danielsen, Pernille Høgh; Karottki, Dorina Gabriela

    2014-01-01

    investigating air pollution particles. There is substantial evidence indicating that exposure to air pollution particles was associated with elevated levels of oxidatively damaged nucleobases in circulating blood cells and urine from humans, which is supported by observations of elevated levels of genotoxicity...... in cultured cells exposed to similar PM. Inflammation is most pronounced in cultured cells and animal models, whereas an elevated level of oxidatively damaged DNA is more pronounced than inflammation in humans. There is non-congruent data showing corresponding variability in effect related to PM sampled...... of PM sampled at different locations or times. Small air pollution particles did not appear more hazardous than larger particles, which is consistent with the notion that constituents such as metals and organic compounds also are important determinants for PM-generated oxidative stress and inflammation...

  13. Flow analysis of vortex generators on wing sections by stereoscopic particle image velocimetry measurements

    DEFF Research Database (Denmark)

    Velte, Clara Marika; Hansen, Martin Otto Laver; Cavar, Dalibor

    2008-01-01

    Stereoscopic particle image velocimetry measurements have been executed in a low speed wind tunnel in spanwise planes in the flow past a row of vortex generators, mounted on a bump in a fashion producing counter-rotating vortices. The measurement technique is a powerful tool which provides all th...

  14. Plasma pressure and particle loss studies in the Pilot-PSI high flux linear plasma generator

    NARCIS (Netherlands)

    Jesko, K.; van der Meiden, H. J.; Gunn, J. P.; Vernimmen, J. W. M.; De Temmerman, G.

    2017-01-01

    Plasma detachment in tokamak divertors reduces the particle and power fluxes to the plasma facing components and is essential for successful operation of ITER. The linear plasma generator Pilot-PSI can produce a high density (∼1021 m−3), low temperature (∼1 eV) plasma which is similar to that

  15. Single step bottom-up process to generate solid phospholipid nano-particles.

    Science.gov (United States)

    Brinkmann-Trettenes, Ulla; Barnert, Sabine; Bauer-Brandl, Annette

    2014-05-01

    The particularity of the Nano Spray Dryer B-90 is the nozzle containing a mesh vibrating at ultrasonic frequency. To study process parameters and processability of crude phospholipid dispersions, in particular the effect of concentration and mesh aperture on both particle size of the dry solid phospholipid nano-particles and on the re-dispersed powder. Phospholipid dispersions containing trehalose as a stabilizer were spray dried. Particle size distributions of dry powders were evaluated by SEM micrographs and by PCS and cryo-TEM for the re-dispersed particles. Spray drying of crude liposome dispersions revealed solid phospholipid nano-particles. Aperture of nozzle mesh and concentration of the dispersions, respectively, both increased the size of solid phospholipid nano-particles. For crude dispersions, an upper limit with respect to processability was found close to below 10% (m/m) even if the crude dispersion was passed along the mesh several times; however, more effective dispersing methods such as pre-sonication can push the limit of processability to higher values. The nano spray dryer is capable of spray drying crude dispersions of phospholipids in concentrations below 10% (m/m) generating solid phospholipid nano-particles relevant for pulmonary delivery. Re-dispersion of spray dried powder reveals liposomes.

  16. Oxidative stress and inflammation generated DNA damage by exposure to air pollution particles.

    Science.gov (United States)

    Møller, Peter; Danielsen, Pernille Høgh; Karottki, Dorina Gabriela; Jantzen, Kim; Roursgaard, Martin; Klingberg, Henrik; Jensen, Ditte Marie; Christophersen, Daniel Vest; Hemmingsen, Jette Gjerke; Cao, Yi; Loft, Steffen

    2014-01-01

    Generation of oxidatively damaged DNA by particulate matter (PM) is hypothesized to occur via production of reactive oxygen species (ROS) and inflammation. We investigated this hypothesis by comparing ROS production, inflammation and oxidatively damaged DNA in different experimental systems investigating air pollution particles. There is substantial evidence indicating that exposure to air pollution particles was associated with elevated levels of oxidatively damaged nucleobases in circulating blood cells and urine from humans, which is supported by observations of elevated levels of genotoxicity in cultured cells exposed to similar PM. Inflammation is most pronounced in cultured cells and animal models, whereas an elevated level of oxidatively damaged DNA is more pronounced than inflammation in humans. There is non-congruent data showing corresponding variability in effect related to PM sampled at different locations (spatial variability), times (temporal variability) or particle size fraction across different experimental systems of acellular conditions, cultured cells, animals and humans. Nevertheless, there is substantial variation in the genotoxic, inflammation and oxidative stress potential of PM sampled at different locations or times. Small air pollution particles did not appear more hazardous than larger particles, which is consistent with the notion that constituents such as metals and organic compounds also are important determinants for PM-generated oxidative stress and inflammation. In addition, the results indicate that PM-mediated ROS production is involved in the generation of inflammation and activated inflammatory cells can increase their ROS production. The observations indicate that air pollution particles generate oxidatively damaged DNA by promoting a milieu of oxidative stress and inflammation. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Laser and Particle Guiding Micro-Elements for Particle Accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Plettner, T.; Gaume, R.; Wisdom, J.; /Stanford U., Phys. Dept.; Spencer, J.; /SLAC

    2005-06-07

    Laser driven particle accelerators require sub-micron control of the laser field as well as precise electron-beam guiding so fabrication techniques that allow integrating both elements into an accelerator-on-chip format become critical for the success of such next generation machines. Micromachining technology for silicon has been shown to be one such feasible technology in PAC2003[1] but with a variety of complications on the laser side. However, fabrication of transparent ceramics has become an interesting technology that could be applied for laser-particle accelerators in several ways. We discuss the advantages such as the range of materials available and ways to implement them followed by some different test examples we been considered. One important goal is an integrated system that avoids having to inject either laser or particle pulses into these structures.

  18. New generation nuclear fuel structures: dense particles in selectively soluble matrix

    Energy Technology Data Exchange (ETDEWEB)

    Sickafus, Kurt E [Los Alamos National Laboratory; Devlin, David J [Los Alamos National Laboratory; Jarvinen, Gordon D [Los Alamos National Laboratory; Patterson, Brian M [Los Alamos National Laboratory; Pattillo, Steve G [Los Alamos National Laboratory; Valdez, James [Los Alamos National Laboratory; Phillips, Jonathan [Los Alamos National Laboratory

    2009-01-01

    We have developed a technology for dispersing sub-millimeter sized fuel particles within a bulk matrix that can be selectively dissolved. This may enable the generation of advanced nuclear fuels with easy separation of actinides and fission products. The large kinetic energy of the fission products results in most of them escaping from the sub-millimeter sized fuel particles and depositing in the matrix during burning of the fuel in the reactor. After the fuel is used and allowed to cool for a period of time, the matrix can be dissolved and the fission products removed for disposal while the fuel particles are collected by filtration for recycle. The success of such an approach would meet a major goal of the GNEP program to provide advanced recycle technology for nuclear energy production. The benefits of such an approach include (1) greatly reduced cost of the actinide/fission product separation process, (2) ease of recycle of the fuel particles, and (3) a radiation barrier to prevent theft or diversion of the recycled fuel particles during the time they are re-fabricated into new fuel. In this study we describe a method to make surrogate nuclear fuels of micrometer scale W (shell)/Mo (core) or HfO2 particles embedded in an MgO matrix that allows easy separation of the fission products and their embedded particles. In brief, the method consists of physically mixing W-Mo or hafnia particles with an MgO precursor. Heating the mixture, in air or argon, without agitation, to a temperature is required for complete decomposition of the precursor. The resulting material was examined using chemical analysis, scanning electron microscopy, X-ray diffraction and micro X-ray computed tomography and found to consist of evenly dispersed particles in an MgO + matrix. We believe this methodology can be extended to actinides and other matrix materials.

  19. A capacitor discharge, quasi-trapezoidal pulse generator for particle extraction

    CERN Document Server

    Bonthond, J

    1995-01-01

    In the CERN SPS Accelerator two methods for particle extraction are used. One of these methods, called Slow Extraction, delivers extracted beams with a duration of up to several seconds to the majority of experiments. The other one, the Fast Resonant Extraction, providing particle bursts with a duration of a few milliseconds, is used for neutrino experiments. For the latter kind of extraction a quadrupole magnet is installed, which is connected to a high voltage pulse generator delivering quasi-trapezoïdal current pulses. The pulse generator is a capacitor discharge system generating current pulses, with a rising slope having 2 different gradients, of which the second one is approximately zero. The falling slope is obtained through natural decay in a freewheel circuit. The use of modern GTO (Gate Turn Off) power switches resulted in a much simpler circuit than the use of standard thyristors would have permitted.

  20. Nanocrystalline oxide (Y{sub 2}O{sub 3}, Dy{sub 2}O{sub 3}, ZrO{sub 2}, NiO) coatings on BaTiO{sub 3} submicron particles by precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Bassano, Alessio [University of Genoa, Department of Chemical and Process Engineering (Italy); Buscaglia, Vincenzo, E-mail: v.buscaglia@ge.ieni.cnr.i [National Research Council, Institute for Energetics and Interphases (Italy); Sennour, Mohamed [Ecole des Mines de Paris, Centre des Materiaux (France); Buscaglia, Maria Teresa; Viviani, Massimo [National Research Council, Institute for Energetics and Interphases (Italy); Nanni, Paolo [University of Genoa, Department of Chemical and Process Engineering (Italy)

    2010-02-15

    Nanocoatings (5-20 nm) of different compounds on fine BaTiO{sub 3} particles were obtained by means of precipitation processes. Homogeneous and smooth shells of Y(OH)CO{sub 3} and Dy(OH)CO{sub 3} were grown from nitrate solutions in the presence of urea. An irregular coating consisting of zirconia nanoparticles was produced from zirconyl nitrate solution using ammonia as a precipitating agent after adsorption of a polymeric polyelectrolyte on the BaTiO{sub 3} surface. Composite particles with a peculiar morphology were obtained by inducing heterogeneous nucleation and growth of Ni(OH){sub 2} lamellae on the BaTiO{sub 3} surface. The different shells can be transformed in a nanocrystalline coating of the corresponding oxide (Y{sub 2}O{sub 3}, Dy{sub 2}O{sub 3}, ZrO{sub 2}, NiO) by calcination at moderate temperatures (400-700 {sup o}C). The overall results indicate that precipitation from solution represents a versatile process to grow a second-phase layer on the surface of BaTiO{sub 3} particles. This approach can be used as an alternative to mechanical wet mixing for controlled doping of ferroelectric materials and for the fabrication of composite materials with specific geometry of the two-phase assembly.

  1. Ultrafine particle removal and ozone generation by in-duct electrostatic precipitators.

    Science.gov (United States)

    Poppendieck, Dustin G; Rim, Donghyun; Persily, Andrew K

    2014-01-01

    Human exposure to airborne ultrafine particles (UFP, electrostatic precipitator filters (ESP) have been shown to be an effective particulate control device for reducing UFP concentrations (20-100 nm) in buildings, although they have the potential to increase indoor ozone concentrations. This study investigated residential ESP filters to reduce ultrafine particles between 4 to 15 nm and quantified the resulting ozone generation. In-duct ESPs were operated in the central air handling unit of a test house. Results for the two tested ESP brands indicate that removal efficiency of 8 to 14 nm particles was near zero and always less than 10% (± 15%), possibly due to particle generation or low charging efficiency. Adding a media filter downstream of the ESP increased the decay rate for particles in the same size range. Continuous operation of one brand of ESP raised indoor ozone concentrations to 77 ppbv and 20 ppbv for a second brand. Using commercial filters containing activated carbon downstream of the installed ESP reduced the indoor steady-state ozone concentrations between 6% and 39%.

  2. The efficiency and stability of bubble formation by acoustic vaporization of submicron perfluorocarbon droplets

    NARCIS (Netherlands)

    Reznik, Nikita; Shpak, O.; Gelderblom, E.C.; Williams, Ross; de Jong, N.; Versluis, Andreas Michel; Burns, Peter N.

    2013-01-01

    Submicron droplets of liquid perfluorocarbon converted into microbubbles with applied ultrasound have been studied, for a number of years, as potential next generation extravascular ultrasound contrast agents. In this work, we conduct an initial ultra-high-speed optical imaging study to examine the

  3. [Development and Performance Evaluation of a Supermicron Particle Generation System for Aerosol Instrument Calibration].

    Science.gov (United States)

    Chen, Xiao-tong; Jiang, Jing-kun; Deng, Jian-guo; Duan, Lei; Hao, Ji-ming

    2016-03-15

    Accurate calibration of aerosol measurement instruments is critical for ensuring the data quality when sampling ambient particulate matter (PM) or those from emission sources. A system for calibrating these instruments was set up, which included an ultrasonic device to generate polydisperse supermicron particles, a chamber, and an aerodynamic particle spectrometer to measure particle size distribution. We verified its performance in stably generated testing aerosol with good spatial uniformity, controlled size distributions and concentrations. The testing aerosol generated had a lognormal distribution. A PM₁₀ and PM₂.₅ two-stage virtual impactor was calibrated using this online method. Collection efficiencies of PM₁₀ and PM₂.₅ stages calibrated by an off-line method using monodisperse particles were also used for comparison. The results from two different methods were consistent with each other. Though the off-line method has been widely used to calibrate PM samplers, it suffers from long experimental duration (2-3 days for calibrating one sampler). In contrast, the online method allows for a rapid calibration (less than half a day for calibrating one sampler).

  4. Impact of in situ polymer coating on particle dispersion into solid laser-generated nanocomposites.

    Science.gov (United States)

    Wagener, Philipp; Brandes, Gudrun; Schwenke, Andreas; Barcikowski, Stephan

    2011-03-21

    The crucial step in the production of solid nanocomposites is the uniform embedding of nanoparticles into the polymer matrix, since the colloidal properties or specific physical properties are very sensitive to particle dispersion within the nanocomposite. Therefore, we studied a laser-based generation method of a nanocomposite which enables us to control the agglomeration of nanoparticles and to increase the single particle dispersion within polyurethane. For this purpose, we ablated targets of silver and copper inside a polymer-doped solution of tetrahydrofuran by a picosecond laser (using a pulse energy of 125 μJ at 33.3 kHz repetition rate) and hardened the resulting colloids into solid polymers. Electron microscopy of these nanocomposites revealed that primary particle size, agglomerate size and particle dispersion strongly depend on concentration of the polyurethane added before laser ablation. 0.3 wt% polyurethane is the optimal polymer concentration to produce nanocomposites with improved particle dispersion and adequate productivity. Lower polyurethane concentration results in agglomeration whereas higher concentration reduces the production rate significantly. The following evaporation step did not change the distribution of the nanocomposite inside the polyurethane matrix. Hence, the in situ coating of nanoparticles with polyurethane during laser ablation enables simple integration into the structural analogue polymer matrix without additives. Furthermore, it was possible to injection mold these in situ-stabilized nanocomposites without affecting particle dispersion. This clarifies that sufficient in situ stabilization during laser ablation in polymer solution is able to prevent agglomeration even in a hot polymer melt.

  5. An Enhanced Quantum-Behaved Particle Swarm Algorithm for Reactive Power Optimization considering Distributed Generation Penetration

    Directory of Open Access Journals (Sweden)

    Runhai Jiao

    2015-01-01

    Full Text Available This paper puts forward a novel particle swarm optimization algorithm with quantum behavior (QPSO to solve reactive power optimization in power system with distributed generation. Moreover, differential evolution (DE operators are applied to enhance the algorithm (DQPSO. This paper focuses on the minimization of active power loss, respectively, and uses QPSO and DQPSO to determine terminal voltage of generators, and ratio of transformers, switching group number of capacitors to achieve optimal reactive power flow. The proposed algorithms are validated through three IEEE standard examples. Comparing the results obtained from QPSO and DQPSO with those obtained from PSO, we find that our algorithms are more likely to get the global optimal solution and have a better convergence. What is more, DQPSO is better than QPSO. Furthermore, with the integration of distributed generation, active power loss has decreased significantly. Specifically, PV distributed generations can suppress voltage fluctuation better than PQ distributed generations.

  6. NONUNIFORMITIES OF TWO-PHASE COOLANT DISTRIBUTION IN A HEAT GENERATING PARTICLES BED

    Directory of Open Access Journals (Sweden)

    V. V. Sorokin

    2014-01-01

    Full Text Available Sufficient atomic power generation safety increase may be done with microfuel adapting to reactor plants with water coolant. Microfuel particle is a millimeter size grain containing fission material core in a protecting coverage. The coverage protects fuel contact with coolant and provides isolation of fission products inside. Well thermophysical properties of microfuel bed in a direct contact with water coolant excludes fuel overheating when accidents. Microfuel use was suggested for a VVER, а direct flow reactor for superheat steam generation, a reactor with neutron spectra adjustment by the steam partial content varying in the coolant.Nonuniformities of two-phase coolant distribution in a heat generating particles bed are predicted by calculations in this text. The one is due to multiple-valuedness of pressure drop across the bed on the steam quality dependency. The nonuniformity decreases with flow rate and particle size growths absolute pressure diminishing while porosity effect is weak. The worse case is for pressure quality of order of one. Some pure steam filled pores appears parallel to steam water mixture filled pores, latter steam quality is less than the mean of the bed. Considering this regime for the direct flow reactor for superheat steam generation we predict some water drops at the exit flow. The two-phase coolant filtration with subcooled water feed is unstable to strong disturbance effects are found. Uniformity of two-phase coolant distribution is worse than for one-phase in the same radial type reactor.

  7. Study to perform preliminary experiments to evaluate particle generation and characterization techniques for zero-gravity cloud physics experiments

    Science.gov (United States)

    Katz, U.

    1982-01-01

    Methods of particle generation and characterization with regard to their applicability for experiments requiring cloud condensation nuclei (CCN) of specified properties were investigated. Since aerosol characterization is a prerequisite to assessing performance of particle generation equipment, techniques for characterizing aerosol were evaluated. Aerosol generation is discussed, and atomizer and photolytic generators including preparation of hydrosols (used with atomizers) and the evaluation of a flight version of an atomizer are studied.

  8. Digital Signal Processing and Generation for a DC Current Transformer for Particle Accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Zorzetti, Silvia [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

    2013-01-01

    The thesis topic, digital signal processing and generation for a DC current transformer, focuses on the most fundamental beam diagnostics in the field of particle accelerators, the measurement of the beam intensity, or beam current. The technology of a DC current transformer (DCCT) is well known, and used in many areas, including particle accelerator beam instrumentation, as non-invasive (shunt-free) method to monitor the DC current in a conducting wire, or in our case, the current of charged particles travelling inside an evacuated metal pipe. So far, custom and commercial DCCTs are entirely based on analog technologies and signal processing, which makes them inflexible, sensitive to component aging, and difficult to maintain and calibrate.

  9. Method for the removal of smut, fine dust and exhaust gas particles, particle catch arrangement for use in this method and use of the particle catch arrangement to generate a static electric field

    NARCIS (Netherlands)

    Ursem, W.N.J.; Marijnissen, J.C.; Roos, R.A.

    2007-01-01

    This inventions provides a method for the removal of smut, fine dust and exhaust gas particles from polluted air comprising providing a particle catch arrangement with a charged surface, the particle catch arrangement being arranged to generate a static electric field, wherein the electric field is

  10. Design of a high DC voltage generator and D-T fuser based on particle accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Wagner L.; Campos, Tarcisio P.R., E-mail: wagnerleite@ufmg.b, E-mail: campos@nuclear.ufmg.b [Universidade Federal de Minas Gerais (DEN/ UFMG), Belo Horizonte, MG (Brazil). Dept. de Engenharia Nuclear

    2011-07-01

    This paper approaches a design and simulation of a high voltage Cockcroft Walton multiplier and a compact size deuteron accelerator addressed in neutron generation by d-t fusion. We proposed a circuit arrangement, which was led to simulations. The particle accelerator was computer-generated providing particle transport and electric potential analysis. As results, the simulated voltage multiplier achieved 119 kV, and the accelerator presented a deuteron beam current up to 15 mA, achieving energies in order to 100 keV. In conclusion, the simulation motivates experimental essays in order to investigate the viability of a deuteron accelerator powered by a Cockcroft-Walton source. Such d-t fusor shall produce an interesting ion beam profile, reaching energy values near the d-t fusion cross section peak. (author)

  11. A novel inlet system for online chemical analysis of semi-volatile submicron particulate matter

    Science.gov (United States)

    Eichler, P.; Müller, M.; D'Anna, B.; Wisthaler, A.

    2015-03-01

    We herein present a novel modular inlet system designed to be coupled to low-pressure gas analyzers for online chemical characterization of semi-volatile submicron particles. The "chemical analysis of aerosol online" (CHARON) inlet consists of a gas-phase denuder for stripping off gas-phase analytes, an aerodynamic lens for particle collimation combined with an inertial sampler for the particle-enriched flow and a thermodesorption unit for particle volatilization prior to chemical analysis. The denuder was measured to remove gas-phase organics with an efficiency > 99.999% and to transmit particles in the 100-750 nm size range with a 75-90% efficiency. The measured average particle enrichment factor in the subsampling flow from the aerodynamic lens was 25.6, which is a factor of 3 lower than the calculated theoretical optimum. We coupled the CHARON inlet to a proton-transfer-reaction time-of-flight mass spectrometer (PTR-ToF-MS) which quantitatively detects most organic analytes and ammonia. The combined CHARON-PTR-ToF-MS setup is thus capable of measuring both the organic and the ammonium fraction in submicron particles in real time. Individual organic compounds can be detected down to levels of 10-20 ng m-3. Two proof-of-principle studies were carried out for demonstrating the analytical power of this new instrumental setup: (i) oxygenated organics and their partitioning between the gas and the particulate phase were observed from the reaction of limonene with ozone and (ii) nicotine was measured in cigarette smoke particles demonstrating that selected organic target compounds can be detected in submicron particles in real time.

  12. Cloning of an Avian Adeno-Associated Virus (AAAV) and Generation of Recombinant AAAV Particles

    OpenAIRE

    Bossis, Ioannis; Chiorini, John A.

    2003-01-01

    Recent studies have proposed that adeno-associated viruses (AAVs) are not evolutionarily linked to other mammalian autonomous parvoviruses but are more closely linked to the autonomous parvoviruses of birds. To better understand the relationship between primate and avian AAVs (AAAVs), we cloned and sequenced the genome of an AAAV (ATCC VR-865) and generated recombinant AAAV particles. The genome of AAAV is 4,694 nucleotides in length and has organization similar to that of other AAVs. The ent...

  13. Removal of Aerosol Particles Generated from Vitrification Process for High-Level Liquid Wastes

    OpenAIRE

    加藤 功

    1990-01-01

    The vitrification technology has been developed for the high-level liquid waste (HLLW) from reprocessing nuclear spent fuel in PNC. The removal performance of the aerosol particles generated from the melting process was studied in a nonradioactive full-scale mock-up test facility (MTF). The off-gas treatment system consists of submerged bed scrubber (SBS), venturi scrubber, NOx absorber, high efficiency mist eliminater (HEME). Deoomtamination factors (DFs) were derived from the mass ratio of ...

  14. Surfactant Effects on Particle Generation in Antibody Formulations in Pre-filled Syringes.

    Science.gov (United States)

    Gerhardt, Alana; Mcumber, Aaron C; Nguyen, Bao H; Lewus, Rachael; Schwartz, Daniel K; Carpenter, John F; Randolph, Theodore W

    2015-12-01

    Protein aggregation and particle formation have been observed when protein solutions contact hydrophobic interfaces, and it has been suggested that this undesirable phenomenon may be initiated by interfacial adsorption and subsequent gelation of the protein. The addition of surfactants, such as polysorbate 20, to protein formulations has been proposed as a way to reduce protein adsorption at silicone oil-water interfaces and mitigate the production of aggregates and particles. In an accelerated stability study, monoclonal antibody formulations containing varying concentrations of polysorbate 20 were incubated and agitated in pre-filled glass syringes (PFS), exposing the protein to silicone oil-water interfaces at the siliconized syringe walls, air-water interfaces, and agitation stress. Following agitation in siliconized syringes that contained an air bubble, lower particle concentrations were measured in the surfactant-containing antibody formulations than in surfactant-free formulations. Polysorbate 20 reduced particle formation when added at concentrations above or below the critical micelle concentration (CMC). The ability of polysorbate 20 to decrease particle generation in PFS corresponded with its ability to inhibit gelation of the adsorbed protein layer, which was assessed by measuring the interfacial diffusion of individual antibody molecules at the silicone oil-water interface using total internal reflectance fluorescence (TIRF) microscopy with single-molecule tracking. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  15. Particle Morphology and Elemental Composition of Smoke Generated by Overheating Common Spacecraft Materials

    Science.gov (United States)

    Meyer, Marit E.

    2015-01-01

    Fire safety in the indoor spacecraft environment is concerned with a unique set of fuels which are designed to not combust. Unlike terrestrial flaming fires, which often can consume an abundance of wood, paper and cloth, spacecraft fires are expected to be generated from overheating electronics consisting of flame resistant materials. Therefore, NASA prioritizes fire characterization research for these fuels undergoing oxidative pyrolysis in order to improve spacecraft fire detector design. A thermal precipitator designed and built for spacecraft fire safety test campaigns at the NASA White Sands Test Facility (WSTF) successfully collected an abundance of smoke particles from oxidative pyrolysis. A thorough microscopic characterization has been performed for ten types of smoke from common spacecraft materials or mixed materials heated at multiple temperatures using the following techniques: SEM, TEM, high resolution TEM, high resolution STEM and EDS. Resulting smoke particle morphologies and elemental compositions have been observed which are consistent with known thermal decomposition mechanisms in the literature and chemical make-up of the spacecraft fuels. Some conclusions about particle formation mechanisms are explored based on images of the microstructure of Teflon smoke particles and tar ball-like particles from Nomex fabric smoke.

  16. Synthesis of ZnO particles using water molecules generated in esterification reaction

    Science.gov (United States)

    Šarić, Ankica; Gotić, Marijan; Štefanić, Goran; Dražić, Goran

    2017-07-01

    Zinc oxide particles were synthesized without the addition of water by autoclaving (anhydrous) zinc acetate/alcohol and zinc acetate/acetic acid/alcohol solutions at 160 °C. The solvothermal synthesis was performed in ethanol or octanol. The structural, optical and morphological characteristics of ZnO particles were investigated by X-ray diffraction (XRD), UV-Vis spectroscopy, FE-SEM and TEM/STEM microscopy. 13C NMR spectroscopy revealed the presence of ester (ethyl- or octyl-acetate) in the supernatants which directly indicate the reaction mechanism. The formation of ester in this esterification reaction generated water molecule in situ, which hydrolyzed anhydrous zinc acetate and initiated nucleation and formation of ZnO. It was found that the size and shape of ZnO particles depend on the type of alcohol used as a solvent and on the presence of acetic acid in solution. The presence of ethanol in the ;pure; system without acetic acid favoured the formation of fine and uniform spherical ZnO nanoparticles (∼20 nm). With the addition of small amount of acetic acid the size of these small nanoparticles increased significantly up to a few hundred nanometers. The addition of small amount of acetic acid in the presence of octanol caused even more radical changes in the shape of ZnO particles, favouring the growth of huge rod-like particles (∼3 μm).

  17. FULL PARTICLE ELECTROMAGNETIC SIMULATIONS OF ENTROPY GENERATION ACROSS A COLLISIONLESS SHOCK

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Zhongwei; Liu, Ying D.; Wang, Rui; Hu, Huidong [State Key Laboratory of Space Weather, National Space Science Center, Chinese Academy of Sciences, Beijing 100190 (China); Parks, George K. [Space Sciences Laboratory, University of California, Berkeley, CA 94720 (United States); Wu, Pin [Department of Physics and Astronomy, University of Delaware, Newark, DE (United States); Huang, Can [CAS Key Laboratory of Geospace Environment, Department of Geophysics and Planetary Science, University of Science and Technology of China, Hefei (China); Shi, Run, E-mail: liuxying@spaceweather.ac.cn [Memorial University of Newfoundland, St. John' s (Canada)

    2014-09-20

    Experimental data from Cluster have shown that entropy density can be generated across Earth's bow shock. These new observations are a starting point for a more sophisticated analysis that includes computer modeling of a collisionless shock using observed shock parameters as input. In this Letter, we present the first comparison between observations and particle-in-cell simulations of such entropy generation across a collisionless shock. The ion heating at the shock is dominated by the phase mixing of reflected and directly transmitted ions, which are separated from the incident ions. The electron heating is a nearly thermal process due to the conservation of their angular momentum. For both species, we calculate the entropy density across the shock, and obtain good consistency between observations and simulations on entropy generation across the shock. We also find that the entropy generation rate is reduced as the shock Mach number decreases.

  18. From plasma to nanoparticles: optical and particle emission of a spark discharge generator

    Science.gov (United States)

    Kohut, A.; Ludvigsson, L.; Meuller, B. O.; Deppert, K.; Messing, M. E.; Galbács, G.; Geretovszky, Zs

    2017-11-01

    The increased demand for high purity nanoparticles (NPs) of defined geometry necessitates the continuous development of generation routes. One of the most promising physical techniques for producing metal, semiconductor or alloy NPs in the gas phase is spark discharge NP generation. The technique has a great potential for up-scaling without altering the particles. Despite the simplicity of the setup, the formation of NPs in a spark discharge takes place via complex multi-scale processes, which greatly hinders the investigation via conventional NP measurement techniques. In the present work, time-resolved optical emission spectroscopy (OES) was used to provide information on the species present in the spark from as early as approximately 100 ns after the initiation of the discharge. We demonstrate that operando emission spectroscopy can deliver valuable insights into NP formation. The emission spectra of the spark are used to identify, among others, the main stages of material erosion and to calculate the quenching rate of the generated metal vapour. We demonstrate that the alteration of key control parameters, that are typically used to optimize NP generation, clearly affect the emission spectra. We report for Cu and Au NPs that the intensity of spectral lines emitted by metal atoms levels off when spark energy is increased above an energy threshold, suggesting that the maximum concentration of metal vapour produced in the generator is limited. This explains the size variation of the generated NPs. We report a strong correlation between the optical and particle emission of the spark discharge generator, which demonstrate the suitability of OES as a valuable characterization tool that will allow for the more deliberate optimization of spark-based NP generation.

  19. Micromagnetic Simulations of Submicron Cobalt Dots

    Energy Technology Data Exchange (ETDEWEB)

    Parker, G.J.; Cerjan, C.

    1999-08-30

    Numerical simulations of submicron Co extruded elliptical dots were performed to illustrate the relative importance of different physical parameters on the switching behavior in the easy direction. Shape, size, magnetic moment magnitude and crystalline anisotropy, both magnitude and distribution, were varied. The simulation includes calculation of the magnetostatic, exchange and crystalline anisotropy fields on a structured mesh using finite difference techniques. The smooth boundary of the dots are accurately represented by use of the Embedded Curve Boundary method.

  20. Submicron Surface-Patterned Fibers and Textiles

    Science.gov (United States)

    2016-11-04

    The patterned fiber surface behaves as an optical diffraction grating when the feature size is comparable with visible light wavelengths. A red laser...the optical fiber gratings For the first diffraction order of the micron and submicron patterned fiber , we utilize the formula α tanh (where s...e) SEM images of patterned PMMA fiber are depicted. The inset shows the cross- section of this fiber . Submitted to 20 Figure S3

  1. Submicron ionography of nanostructures using a femtosecond-laser-driven-cluster-based source

    OpenAIRE

    Faenov, A. Ya; Pikuz, T. A.; Fukuda, Y.(Miyagi University of Education, Department of Physics, Sendai, Japan); Kando, M; Kotaki, H.; Homma, T.; KAWASE, K; Kameshima, T.; Pirozkhov, A.; Yogo, A.; Tampo, M.; Mori, M.; Sakaki, H.; Hayashi, Y; Nakamura, T.

    2009-01-01

    An intense isotropic source of multicharged carbon and oxygen ions with energy above 300 keV and particle number >108 per shot was obtained by femtosecond Ti:Sa laser irradiation of submicron clusters. The source was employed for high-contrast contact ionography images with 600 nm spatial resolution. A variation in object thickness of 100 nm was well resolved for both Zr and polymer foils.

  2. Comprehensive investigation of the dynamics of micron and submicron lunar ejecta in heliocentric space

    Energy Technology Data Exchange (ETDEWEB)

    Hargrave, A.D.

    1984-01-01

    The forces which act on micron and submicron dust particles in interplanetary space are studied in detail. Particular attention is given to Mie scattering theory as it applies to the calculation of the force due to radiation pressure. All of the forces are integrated into a computer model to study the heliocentric orbits of lunar ejecta. It is shown that lunar ejecta contribute to a geocentric dust cloud, as well as to a heliocentric dust belt.

  3. Physicochemical and optical properties of combustion-generated particles from Ship Diesel Engines

    Science.gov (United States)

    Kim, H.; Jeong, S.; Jin, H. C.; Kim, J. Y.

    2015-12-01

    Shipping contributes significantly to the anthropogenic burden of particulate matter (PM), and is among the world's highest polluting combustion sources per fuel consumed. Moreover, ships are a highly concentrated source of pollutants which are emitted into clean marine environments (e.g., Artic region). Shipping utilizes heavy fuel oil (HFO) which is less distilled compared to fuels used on land and few investigations on shipping related PM properties are available. BC is one of the dominant combustion products of ship diesel engines and its chemical and microphysical properties have a significant impact on climate by influencing the amount of albedo reduction on bright surfaces such as in polar regions. We have carried out a campaign to characterize the PM emissions from medium-sized marine engines in Gunsan, Jeonbuk Institute of Automotive Technology. The properties of ship-diesel PM have characterized depending on (1) fuel sulfur content (HFO vs. ULSD) and (2) engine conditions (Running state vs. Idling state). Scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), energy-dispersive X-ray spectroscopy (EDX) equipped with HRTEM and Raman spectroscopy were used for physicochemical analysis. Optical properties, which are ultimately linked to the snow/ice albedo decrease impacting climate, were assessed as well. PM generated under high engine temperature conditions had typical features of soot, e.g., concentric circles comprised of closely packed graphene layers, however PM generated by the idling state at low combustion temperature was characterized by amorphous and droplet-like carbonaceous particles with no crystalline structure. Significant differences in optical properties depending on the combustion conditions were also observed. Particles from running conditions showed wavelength-independent absorbing properties, whereas the particles from idling conditions showed enhanced absorption at shorter wavelengths, which is

  4. Phase transformation and intense 2.7 μm emission from Er3+ doped YF3/YOF submicron-crystals.

    Science.gov (United States)

    Chai, Guanqi; Dong, Guoping; Qiu, Jianrong; Zhang, Qinyuan; Yang, Zhongmin

    2013-01-01

    Yttrium fluoride YF3:Er(3+) and yttrium oxyfluoride YOF:Er(3+) submicron-crystals with mid-infrared fluorescent emissions were synthesized for the first time. The rhombohedral phase YOF submicron-crystals were synthesized by the crystalline phase transformation from pure orthorhombic YF3 submicron-crystals, which were prepared by co-precipitation method. The composition and morphology were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM) and transmission electron microscopy (TEM), which showed that submicron-crystals were quasi-spherical with the particle size of ~400 nm. A novel formation mechanism of YOF submicron-crystals was proposed. Photoluminescence (PL) spectra indicated the 2.7 μm emission of Er(3+) has remarkably enhanced with the increase of Er(3+) doping concentration, and a novel dynamic circulatory energy transfer mechanism was proposed. Fourier transform infrared spectra (FTIR) were used to demonstrate the change of hydroxyl content. These oxyfluoride submicron-crystals provide a new material for nano/submicron-crystals-glass composites, and open a brand new field for the realization of mid-infrared micro/nano-lasers.

  5. Effects of volatile coatings on the morphology and optical detection of combustion-generated black carbon particles.

    Energy Technology Data Exchange (ETDEWEB)

    Bambha, Ray.; Dansson, Mark A; Schrader, Paul E.; Michelsen, Hope A.

    2013-09-01

    We have measured time-resolved laser-induced incandescence (LII) from combustion-generated mature soot extracted from a burner and (1) coated with oleic acid or (2) coated with oleic acid and then thermally denuded using a thermodenuder. The soot samples were size selected using a differential mobility analyser and characterized with a scanning mobility particle sizer, centrifugal particle mass analyser, and transmission electron microscope. The results demonstrate a strong influence of coatings particle morphology and on the magnitude and temporal evolution of the LII signal. For coated particles higher laser fluences are required to reach LII signal levels comparable to those of uncoated particles. This effect is predominantly attributable to the additional energy needed to vaporize the coating while heating the particle. LII signals are higher and signal decay rates are significantly slower for thermally denuded particles relative to coated or uncoated particles, particularly at low and intermediate laser fluences.

  6. Laser generation of shock waves in a water suspension with light-absorbing particles.

    Science.gov (United States)

    Besaga, Vira R; Maksimyak, Andrew P; Maksimyak, Peter P

    2014-04-01

    We report the generation of shock waves in a disperse medium with absorbing particles of black pigment in the water using continuous laser radiation. As a result of the experimental investigation it was found that the illuminating beam diameter growth at the constant laser power results in the decrease of the signals' modulation frequencies, improving their stability and increasing their amplitudes. In turn, the decrease of the signal's modulation frequency is caused by the growth of time, which is needed for heating the medium to the critical temperature of cavitation. Improving the stability and the increase of optical and acoustic signal amplitudes take place, due to the growth of the medium volume and hence the number of pigment particles that participate in cavitation.

  7. Generating Irregular Models for 3D Spherical-Particle-Based Numerical Methods

    Directory of Open Access Journals (Sweden)

    Gang-Hai Huang

    2013-01-01

    Full Text Available The realistic representation of an irregular geological body is essential to the construction of a particle simulation model. A three-dimensional (3D sphere generator for an irregular model (SGIM, which is based on the platform of Microsoft Foundation Classes (MFC in VC++, is developed to accurately simulate the inherent discontinuities in geological bodies. OpenGL is employed to visualize the modeling in the SGIM. Three key functions, namely, the basic-model-setup function, the excavating function, and the cutting function, are implemented. An open-pit slope is simulated using the proposed model. The results demonstrate that an extremely irregular 3D model of a geological body can be generated using the SGIM and that various types of discontinuities can be inserted to cut the model. The data structure of the model that is generated by the SGIM is versatile and can be easily modified to match various numerical calculation tools. This can be helpful in the application of particle simulation methods to large-scale geoengineering projects.

  8. Laser direct writing using submicron-diameter fibers.

    Science.gov (United States)

    Tian, Feng; Yang, Guoguang; Bai, Jian; Xu, Jianfeng; Hou, Changlun; Liang, Yiyong; Wang, Kaiwei

    2009-10-26

    In this paper, a novel direct writing technique using submicron-diameter fibers is presented. The submicron-diameter fiber probe serves as a tightly confined point source and it adopts micro touch mode in the process of writing. The energy distribution of direct writing model is analyzed by Three-Dimension Finite-Difference Time-Domain method. Experiments demonstrate that submicron-diameter fiber direct writing has some advantages: simple process, 350-nm-resolution (lower than 442-nm-wavelength), large writing area, and controllable width of lines. In addition, by altering writing direction of lines, complex submicron patterns can be fabricated.

  9. Particle deposition modeling in the secondary side of a steam generator bundle model

    Energy Technology Data Exchange (ETDEWEB)

    Mukin, Roman, E-mail: roman.mukin@psi.ch; Dehbi, Abdel, E-mail: abdel.dehbi@psi.ch

    2016-04-01

    A steam generator (SG) tube rupture (SGTR) model is studied in this paper. This model based on a experimental facility called Aerosol Trapping In a Steam Generator (ARTIST), which is a model of a scaled steam generator tube bundle consisting of 270 tubes and a guillotine tube to address aerosol deposition phenomena on two different scales: near the tube break, where the gas velocities and turbulence are very intensive, and far away from the break, where the flow velocities are three orders of magnitude lower. Owing to complexity of the flow, 3D simulations with highly resolved computational mesh near the break were done. First, the flow inside an isolated tube with a guillotine tube break has been studied in the framework of Reynolds Averaged Navier Stokes (RANS) approach. The next part is devoted to the simulation of an inclined gas jet entering the SG tube bundle via the guillotine tube breach with more advanced CFD tools. In particular, Detached Eddy Simulation (DES) and RANS are applied to tackle the wide range of flow scales. Flow field velocity comparison showed that DES results are reproducing wavy structure of the flow field in far field from the break observed in experiment. Particle transport and deposition is modelled by Lagrangian continuous random walk (CRW) model, which has been developed and validated previously. It is found that the DES combined with the CRW to supply fluctuating velocity components predicts deposition rates that are generally within the scatter of the measured data. Monodisperse, spherical SiO{sub 2} particles with AMMD = 1.4 μm were used as aerosol particles in simulations. To be economically feasible, the computations were made with the open source CFD code OpenFOAM. Comparison of the calculated flow with the experimental axial velocity distribution data at different vertical levels has been performed.

  10. Prototype Generation Using Multiobjective Particle Swarm Optimization for Nearest Neighbor Classification.

    Science.gov (United States)

    Hu, Weiwei; Tan, Ying

    2016-12-01

    The nearest neighbor (NN) classifier suffers from high time complexity when classifying a test instance since the need of searching the whole training set. Prototype generation is a widely used approach to reduce the classification time, which generates a small set of prototypes to classify a test instance instead of using the whole training set. In this paper, particle swarm optimization is applied to prototype generation and two novel methods for improving the classification performance are presented: 1) a fitness function named error rank and 2) the multiobjective (MO) optimization strategy. Error rank is proposed to enhance the generation ability of the NN classifier, which takes the ranks of misclassified instances into consideration when designing the fitness function. The MO optimization strategy pursues the performance on multiple subsets of data simultaneously, in order to keep the classifier from overfitting the training set. Experimental results over 31 UCI data sets and 59 additional data sets show that the proposed algorithm outperforms nearly 30 existing prototype generation algorithms.

  11. [Nasal submicron emulsion of Scutellariae Radix extract preparation technology research based on phase transfer of solute technology].

    Science.gov (United States)

    Shi, Ya-jun; Shi, Jun-hui; Chen, Shi-bin; Yang, Ming

    2015-07-01

    Based on the demand of nasal drug delivery high drug loadings, using the unique phase transfer of solute, integrating the phospholipid complex preparation and submicron emulsion molding process of Scutellariae Radix extract, the study obtained the preparation of the high drug loadings submicron emulsion of Scutellariae Radix extract. In the study of drug solution dispersion method, the uniformity of drug dispersed as the evaluation index, the traditional mixing method, grinding, homogenate and solute phase transfer technology were investigated, and the solute phase transfer technology was adopted in the last. With the adoption of new technology, the drug loading capacity reached 1.33% (phospholipid complex was 4%). The drug loading capacity was improved significantly. The transfer of solute method and timing were studied as follows,join the oil phase when the volume of phospholipid complex anhydrous ethanol solution remaining 30%, the solute phase transfer was completed with the continued recycling of anhydrous ethanol. After drug dissolved away to oil phase, the preparation technology of colostrum was determined with the evaluation index of emulsion droplet form. The particle size of submicron emulsion, PDI and stability parameters were used as evaluation index, orthogonal methodology were adopted to optimize the submicron emulsion ingredient and main influential factors of high pressure homogenization technology. The optimized preparation technology of Scutellariae Radix extract nasal submicron emulsion is practical and stable.

  12. Generation of controllable plasma wakefield noise in particle-in-cell simulations

    Science.gov (United States)

    Moschuering, N.; Ruhl, H.; Spitsyn, R. I.; Lotov, K. V.

    2017-10-01

    Numerical simulations of beam-plasma instabilities may produce quantitatively incorrect results because of unrealistically high initial noise from which the instabilities develop. Of particular importance is the wakefield noise, the potential perturbations that have a phase velocity which is equal to the beam velocity. Controlling the noise level in simulations may offer the possibility of extrapolating simulation results to the more realistic low-noise case. We propose a novel method for generating wakefield noise with a controllable amplitude by randomly located charged rods propagating ahead of the beam. We also illustrate the method with particle-in-cell simulations. The generation of this noise is not accompanied by parasitic Cherenkov radiation waves.

  13. Applying Sequential Particle Swarm Optimization Algorithm to Improve Power Generation Quality

    Directory of Open Access Journals (Sweden)

    Abdulhafid Sallama

    2014-10-01

    Full Text Available Swarm Optimization approach is a heuristic search method whose mechanics are inspired by the swarming or collaborative behaviour of biological populations. It is used to solve constrained, unconstrained, continuous and discrete problems. Swarm intelligence systems are widely used and very effective in solving standard and large-scale optimization, provided that the problem does not require multi solutions. In this paper, particle swarm optimisation technique is used to optimise fuzzy logic controller (FLC for stabilising a power generation and distribution network that consists of four generators. The system is subject to different types of faults (single and multi-phase. Simulation studies show that the optimised FLC performs well in stabilising the network after it recovers from a fault. The controller is compared to multi-band and standard controllers.

  14. Development of test particle module for impurity generation and transport in BOUT++ framework

    Science.gov (United States)

    Xiao, Xiaotao; Xu, Xueqiao

    2014-10-01

    Developing the test particle module in BOUT++ framework is the first step to enhance its capability to simulate impurity generation and transport in edge plasmas, which potentially can be extended to efficiently simulate both turbulence and neoclassical physics in realistic geometry. The motion of impurity charged particles are governed by guiding-center (GC) equations in the presence of turbulent electromagnetic fields. The GC equations are the well-known Hamiltonian guiding center equation given by Littlejohn, Boozer, White and others. The Fourth-order Runge-Kutta algorithm is used to advance the GC equations in time. In order easily to couple with BOUT++ fluid module, the same field aligned coordinates are used except near the region close to X-point. The bilinear interpolation is used to interpolate 3D fluid turbulent electromagnetic fields from grid points to particle positions. The calculated orbits in equilibrium configuration are checked to conserve constants of motion. The various guiding-center orbits in divertor configuration under BOUT++ framework are demonstrated and benchmarked. Then spatial distribution of impurities in edge plasmas from given sources at the divertor plates and at the protection limiters near RF antennas is obtained in given background plasma. This work was performed for USDOE by LLNL under DE-AC52-07NA27344, LLNL LDRD project 12-ERD-022 and the China Natural Science Foundation under Contract No. 11105185.

  15. Diagnostics of Particles emitted from a Laser generated Plasma: Experimental Data and Simulations

    Directory of Open Access Journals (Sweden)

    Costa Giuseppe

    2018-01-01

    Full Text Available The charge particle emission form laser-generated plasma was studied experimentally and theoretically using the COMSOL simulation code. The particle acceleration was investigated using two lasers at two different regimes. A Nd:YAG laser, with 3 ns pulse duration and 1010 W/cm2 intensity, when focused on solid target produces a non-equilibrium plasma with average temperature of about 30-50 eV. An Iodine laser with 300 ps pulse duration and 1016 W/cm2 intensity produces plasmas with average temperatures of the order of tens keV. In both cases charge separation occurs and ions and electrons are accelerated at energies of the order of 200 eV and 1 MeV per charge state in the two cases, respectively. The simulation program permits to plot the charge particle trajectories from plasma source in vacuum indicating how they can be deflected by magnetic and electrical fields. The simulation code can be employed to realize suitable permanent magnets and solenoids to deflect ions toward a secondary target or detectors, to focalize ions and electrons, to realize electron traps able to provide significant ion acceleration and to realize efficient spectrometers. In particular it was applied to the study two Thomson parabola spectrometers able to detect ions at low and at high laser intensities. The comparisons between measurements and simulation is presented and discussed.

  16. Hydrothermal Synthesis of Co-Ru Alloy Particle Catalysts for Hydrogen Generation from Sodium Borohydride

    Directory of Open Access Journals (Sweden)

    Marija Kurtinaitienė

    2013-01-01

    Full Text Available We report the synthesis of μm and sub-μm-sized Co, Ru, and Co-Ru alloy species by hydrothermal approach in the aqueous alkaline solutions (pH ≥ 13 containing CoCl2 and/or RuCl3, sodium citrate, and hydrazine hydrate and a study of their catalytic properties for hydrogen generation by hydrolysis of sodium borohydride solution. This way provides a simple platform for fabrication of the ball-shaped Co-Ru alloy catalysts containing up to 12 wt% Ru. Note that bimetallic Co-Ru alloy bowls containing even 7 at.% Ru have demonstrated catalytic properties that are comparable with the ones of pure Ru particles fabricated by the same method. This result is of great importance in view of the preparation of cost-efficient catalysts for hydrogen generation from borohydrides. The morphology and composition of fabricated catalyst particles have been characterized using scanning electron microscopy, energy dispersive X-ray diffraction, and inductively coupled plasma optical emission spectrometry.

  17. Laboratory-generated mixtures of mineral dust particles with biological substances: characterization of the particle mixing state and immersion freezing behavior

    Science.gov (United States)

    Augustin-Bauditz, Stefanie; Wex, Heike; Denjean, Cyrielle; Hartmann, Susan; Schneider, Johannes; Schmidt, Susann; Ebert, Martin; Stratmann, Frank

    2016-05-01

    Biological particles such as bacteria, fungal spores or pollen are known to be efficient ice nucleating particles. Their ability to nucleate ice is due to ice nucleation active macromolecules (INMs). It has been suggested that these INMs maintain their nucleating ability even when they are separated from their original carriers. This opens the possibility of an accumulation of such INMs in soils, resulting in an internal mixture of mineral dust and INMs. If particles from such soils which contain biological INMs are then dispersed into the atmosphere due to wind erosion or agricultural processes, they could induce ice nucleation at temperatures typical for biological substances, i.e., above -20 up to almost 0 °C, while they might be characterized as mineral dust particles due to a possibly low content of biological material. We conducted a study within the research unit INUIT (Ice Nucleation research UnIT), where we investigated the ice nucleation behavior of mineral dust particles internally mixed with INM. Specifically, we mixed a pure mineral dust sample (illite-NX) with ice active biological material (birch pollen washing water) and quantified the immersion freezing behavior of the resulting particles utilizing the Leipzig Aerosol Cloud Interaction Simulator (LACIS). A very important topic concerning the investigations presented here as well as for atmospheric application is the characterization of the mixing state of aerosol particles. In the present study we used different methods like single-particle aerosol mass spectrometry, Scanning Electron Microscopy (SEM), Energy Dispersive X-ray analysis (EDX), and a Volatility-Hygroscopicity Tandem Differential Mobility Analyser (VH-TDMA) to investigate the mixing state of our generated aerosol. Not all applied methods performed similarly well in detecting small amounts of biological material on the mineral dust particles. Measuring the hygroscopicity/volatility of the mixed particles with the VH-TDMA was the most

  18. Laboratory-generated mixtures of mineral dust particles with biological substances: characterization of the particle mixing state and immersion freezing behavior

    Directory of Open Access Journals (Sweden)

    S. Augustin-Bauditz

    2016-05-01

    Full Text Available Biological particles such as bacteria, fungal spores or pollen are known to be efficient ice nucleating particles. Their ability to nucleate ice is due to ice nucleation active macromolecules (INMs. It has been suggested that these INMs maintain their nucleating ability even when they are separated from their original carriers. This opens the possibility of an accumulation of such INMs in soils, resulting in an internal mixture of mineral dust and INMs. If particles from such soils which contain biological INMs are then dispersed into the atmosphere due to wind erosion or agricultural processes, they could induce ice nucleation at temperatures typical for biological substances, i.e., above −20 up to almost 0 °C, while they might be characterized as mineral dust particles due to a possibly low content of biological material. We conducted a study within the research unit INUIT (Ice Nucleation research UnIT, where we investigated the ice nucleation behavior of mineral dust particles internally mixed with INM. Specifically, we mixed a pure mineral dust sample (illite-NX with ice active biological material (birch pollen washing water and quantified the immersion freezing behavior of the resulting particles utilizing the Leipzig Aerosol Cloud Interaction Simulator (LACIS. A very important topic concerning the investigations presented here as well as for atmospheric application is the characterization of the mixing state of aerosol particles. In the present study we used different methods like single-particle aerosol mass spectrometry, Scanning Electron Microscopy (SEM, Energy Dispersive X-ray analysis (EDX, and a Volatility–Hygroscopicity Tandem Differential Mobility Analyser (VH-TDMA to investigate the mixing state of our generated aerosol. Not all applied methods performed similarly well in detecting small amounts of biological material on the mineral dust particles. Measuring the hygroscopicity/volatility of the mixed particles with the VH

  19. Submicron particles of Co, Ni and Co–Ni alloys

    Indian Academy of Sciences (India)

    Unknown

    Solid State Ionics 84 271. Ayyappan S, Gopalan R S, Subbanna G N and Rao C N R 1997. J. Mater. Res. 12 398. Bradley J S 1994 Clusters and colloids: From theory to appli- cations (eds) G Schmid (Weinheim: VCH) Ch. 1. Cullity B D 1972 Introduction to magnetic materials (Reading,. Massachusetts: Addison-Wesley).

  20. Microscopic imaging ellipsometry of submicron-scale bacterial cells ...

    African Journals Online (AJOL)

    Microscopic imaging ellipsometry of submicron-scale bacterial cells. ... Conclusion: MIE is a sensitive non-optical technique that can be used to image biological systems without the need for labeling of molecules. Keywords: Objective plane, Imaging ellipsometry, Submicron-scale bacterial cells, Streptococcus mutans, ...

  1. Moment expansion approach to calculate impact ionization rate in submicron silicon devices

    Science.gov (United States)

    Sonoda, Ken-ichiro; Yamaji, Mitsuru; Taniguchi, Kenji; Hamaguchi, Chihiro; Dunham, Scott T.

    1996-11-01

    A method to calculate the impact ionization rate in submicron silicon devices is developed using both an average energy and an average square energy of electrons. The method consists of an impact ionization model formulated with the average energy and conservation equations for the average square energy in the framework of an energy transport model. Parameters for the transport equations are extracted in such a way that calculated moments based on these equations match Monte Carlo simulation results. The impact ionization generation rate in an n+nn+ structure calculated with this method agrees well with the results obtained from Monte Carlo simulation. The new method is also applied to a submicron n-MOSFET. The calculated distribution of the generation rate is found to be quite different from the results based on a conventional method.

  2. Generation of hydrogen peroxide from San Joaquin Valley particles in a cell-free solution

    Directory of Open Access Journals (Sweden)

    H. Shen

    2011-01-01

    generation. By measuring calibration curves of HOOH generation from copper, and quantifying copper concentrations in our particle extracts, we find that PBS-soluble copper is primarily responsible for HOOH production by the Fresno PM. Extrapolating our results to expected concentrations of PM-derived HOOH in human lung lining fluid suggests that typical daily PM exposures in the San Joaquin Valley are unlikely to cause HOOH-mediated acute health effects, but that very high PM events might lead to cytotoxic levels of pulmonary HOOH.

  3. Plasma pressure and particle loss studies in the Pilot-PSI high flux linear plasma generator

    Directory of Open Access Journals (Sweden)

    K. Ješko

    2017-08-01

    Full Text Available Plasma detachment in tokamak divertors reduces the particle and power fluxes to the plasma facing components and is essential for successful operation of ITER. The linear plasma generator Pilot-PSI can produce a high density (∼1021 m−3, low temperature (∼1eV plasma which is similar to that expected at the ITER divertor strike-points during the partially detached regime [1]. Given the simple geometry of the device, Pilot-PSI allows to diagnose the plasma beam at multiple axial positions. In this study, the incoherent Thomson scattering (TS diagnostic [2] is exploited to measure the radial plasma Te and ne profiles at two locations of the hydrogen plasma beam: near the plasma source (upstream and 2cm from the target plate. At the target, the TS measurements are supported by an embedded Langmuir probe. These measurements prove the existence of parallel plasma pressure loss as well as particle loss, confirming that physical processes believed to cause detachment in tokamak divertors also hold in Pilot-PSI (ion-neutral friction, volume recombination. It is found that the fractional reduction of the plasma pressure varies between ∼4 and ∼5000, depending strongly on the pressure of the background neutrals. The importance of individual loss channels is discussed.

  4. Particle size characterization of aerosols generated during surface contaminated concrete demolition.

    Science.gov (United States)

    MacMillan, Walter J; Brey, Richard R; Harris, Jason T

    2013-05-01

    The purpose of this study was to measure mass and activity distributions from the aerosols generated during the demolition of surface contaminated concrete. Air samples were collected using a cascade impactor during the mechanical hammering and dismantlement of radiologically contaminated high level waste process vaults from which the piping and components had been previously removed. The experimentally determined distribution parameters were compared with the 5.0-μm particle size referenced in the U.S. Department of Energy (U.S. DOE) regulations pertaining to internal deposition (10CFR835 and ICRP66). Mass distribution parameters were compared with their activity distribution counterparts. The Mass Median Aerodynamic Diameter (MMAD) was determined to be 4.2 μm with a Mass Geometric Standard Deviation (GSDM) of 2.3 μm, and the Co Activity Median Aerodynamic Diameter (AMAD) was determined to be 3.9 μm with an Activity Geometric Standard Deviation (GSDA) of 2.3 μm. These results are consistent with the ICRP66 5.0-μm reference particle size and the Derived Air Concentration (DAC) values referenced in 10CFR835 and utilized throughout the U.S. DOE complex.

  5. Plasma Processing of SRF Cavities for the next Generation Of Particle Accelerators

    Energy Technology Data Exchange (ETDEWEB)

    Vuskovic, Leposava

    2015-11-23

    The cost-effective production of high frequency accelerating fields are the foundation for the next generation of particle accelerators. The Ar/Cl2 plasma etching technology holds the promise to yield a major reduction in cavity preparation costs. Plasma-based dry niobium surface treatment provides an excellent opportunity to remove bulk niobium, eliminate surface imperfections, increase cavity quality factor, and bring accelerating fields to higher levels. At the same time, the developed technology will be more environmentally friendly than the hydrogen fluoride-based wet etching technology. Plasma etching of inner surfaces of standard multi-cell SRF cavities is the main goal of this research in order to eliminate contaminants, including niobium oxides, in the penetration depth region. Successful plasma processing of multi-cell cavities will establish this method as a viable technique in the quest for more efficient components of next generation particle accelerators. In this project the single-cell pill box cavity plasma etching system is developed and etching conditions are determined. An actual single cell SRF cavity (1497 MHz) is plasma etched based on the pill box cavity results. The first RF test of this plasma etched cavity at cryogenic temperature is obtained. The system can also be used for other surface modifications, including tailoring niobium surface properties, surface passivation or nitriding for better performance of SRF cavities. The results of this plasma processing technology may be applied to most of the current SRF cavity fabrication projects. In the course of this project it has been demonstrated that a capacitively coupled radio-frequency discharge can be successfully used for etching curved niobium surfaces, in particular the inner walls of SRF cavities. The results could also be applicable to the inner or concave surfaces of any 3D structure other than an SRF cavity.

  6. Exposure to wear particles generated from studded tires and pavement induces inflammatory cytokine release from human macrophages.

    Science.gov (United States)

    Lindbom, John; Gustafsson, Mats; Blomqvist, Göran; Dahl, Andreas; Gudmundsson, Anders; Swietlicki, Erik; Ljungman, Anders G

    2006-04-01

    Health risks associated with exposure to airborne particulate matter (PM) have been shown epidemiologically as well as experimentally, pointing to both respiratory and cardiovascular effects. Lately, wear particles generated from traffic have been recognized to be a major contributing source to the overall particle load, especially in the Nordic countries were studded tires are used. In this work, we investigated the inflammatory effect of PM10 generated from the wear of studded tires on two different types of pavement. As comparison, we also investigated PM10 from a traffic-intensive street, a subway station, and diesel exhaust particles (DEP). Human monocyte-derived macrophages, nasal epithelial cells (RPMI 2650), and bronchial epithelial cells (BEAS-2B) were exposed to the different types of particles, and the secretion of IL-6, IL-8, IL-10, and TNF-alpha into the culture medium was measured. The results show a significant release of cytokines from macrophages after exposure for all types of particles. When particles generated from asphalt/granite pavement were compared to asphalt/quartzite pavement, the granite pavement had a significantly higher capacity to induce the release of cytokines. The granite pavement particles induced cytokine release at the same magnitude as the street particles did, which was higher than what particles from both a subway station and DEP did. Exposure of epithelial cells to PM10 resulted in a significant increase of TNF-alpha secreted from BEAS-2B cells for all types of particles used (DEP was not tested), and the highest levels were induced by subway particles. None of the particle types were able to evoke detectable cytokine release from RPMI 2650 cells. The results indicate that PM10 generated by the wear of studded tires on the street surface is a large contributor to the cytokine-releasing ability of particles in traffic-intensive areas and that the type of pavement used is important for the level of this contribution

  7. On the interaction between radon progeny and particles generated by electronic and traditional cigarettes

    Science.gov (United States)

    Vargas Trassierra, C.; Cardellini, F.; Buonanno, G.; De Felice, P.

    2015-04-01

    During their entire lives, people are exposed to the pollutants present in indoor air. Recently, Electronic Nicotine Delivery Systems, mainly known as electronic cigarettes, have been widely commercialized: they deliver particles into the lungs of the users but a "second-hand smoke" has yet to be associated to this indoor source. On the other hand, the naturally-occurring radioactive gas, i.e. radon, represents a significant risk for lung cancer, and the cumulative action of these two agents could be worse than the agents separately would. In order to deepen the interaction between radon progeny and second-hand aerosol from different types of cigarettes, a designed experimental study was carried out by generating aerosol from e-cigarette vaping as well as from second-hand traditional smoke inside a walk-in radon chamber at the National Institute of Ionizing Radiation Metrology (INMRI) of Italy. In this chamber, the radon present in air comes naturally from the floor and ambient conditions are controlled. To characterize the sidestream smoke emitted by cigarettes, condensation particle counters and scanning mobility particle sizer were used. Radon concentration in the air was measured through an Alphaguard ionization chamber, whereas the measurement of radon decay product in the air was performed with the Tracelab BWLM Plus-2S Radon daughter Monitor. It was found an increase of the Potential Alpha-Energy Concentration (PAEC) due to the radon decay products attached to aerosol for higher particle number concentrations. This varied from 7.47 ± 0.34 MeV L-1 to 12.6 ± 0.26 MeV L-1 (69%) for the e-cigarette. In the case of traditional cigarette and at the same radon concentration, the increase was from 14.1 ± 0.43 MeV L-1 to 18.6 ± 0.19 MeV L-1 (31%). The equilibrium factor increases, varying from 23.4% ± 1.11% to 29.5% ± 0.26% and from 30.9% ± 1.0% to 38.1 ± 0.88 for the e-cigarette and traditional cigarette, respectively. These growths still continue for long

  8. DRAGON: Monte Carlo generator of particle production from a fragmented fireball in ultrarelativistic nuclear collisions

    Science.gov (United States)

    Tomášik, Boris

    2009-09-01

    A Monte Carlo generator of the final state of hadrons emitted from an ultrarelativistic nuclear collision is introduced. An important feature of the generator is a possible fragmentation of the fireball and emission of the hadrons from fragments. Phase space distribution of the fragments is based on the blast wave model extended to azimuthally non-symmetric fireballs. Parameters of the model can be tuned and this allows to generate final states from various kinds of fireballs. A facultative output in the OSCAR1999A format allows for a comprehensive analysis of phase-space distributions and/or use as an input for an afterburner. Program summaryProgram title: DRAGON Catalogue identifier: AEDK_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEDK_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: Standard CPC licence, http://cpc.cs.qub.ac.uk/licence/licence.html No. of lines in distributed program, including test data, etc.: 6383 No. of bytes in distributed program, including test data, etc.: 32 756 Distribution format: tar.gz Programming language: C++ Computer: PC Pentium 4, though no particular tuning for this machine was performed Operating system: Linux; the program has been successfully run on Gentoo Linux 2.6, RedHat Linux 9, Debian Linux 4.0, all with g++ compiler. It also ran successfully on MS Windows under Microsoft Visual C++ 2008 Express Edition as well as under cygwin/g++ RAM: 100 Mbytes Supplementary material: Sample output files from the test run, provided in the distribution, are available. Classification: 11.2 Nature of problem: Deconfined matter produced in ultrarelativistic nuclear collisions expands and cools down and eventually returns into the confined phase. If the expansion is fast, the fireball could fragment either due to spinodal decomposition or due to suddenly arising bulk viscous force. Particle abundances are reasonably well described with just a few parameters

  9. Airborne studies of submicron aerosol in the troposphere over West Siberia

    Energy Technology Data Exchange (ETDEWEB)

    Panchenko, M.V.; Zuev, V.E.; Belan, B.D.; Terpugova, S.A. [Institute of Atmospheric Optics, Tomsk (Russian Federation)

    1996-04-01

    Submicron fraction particles that have the longest lifespan and are included in almost all atmospheric processes are of special importance among the great variety of sizes of particles present in the atmosphere. Submicron particles mainly determine the opticle state of the atmosphere in the visible spectral range, essentially cause the absorption of infrared radiation and, since they are the products and participants in all aerosol-to-gas transformations, accumulate of a lot of various chemical compounds and transfer them to large distances. Investigation of the processes of the spatial-temporal variability of aerosol particles for different climatic zones of the earth is the experimental base for studying their effect on climatically and ecologically significant factors and estimating their unfavorable tendencies. The increasing anthropogenic loading of the earth`s atmosphere is creating an urgency for aerosol research. Regardless of how perfect the analytical and numerical methods of solving radiation problems may be, success in forecasting climatic change is mainly determined by the reliability of the experimental data on optical parameters of the atmosphere and of the description of their variability under the effect of external factors.

  10. Characterization of particle size distribution of mainstream cigarette smoke generated by smoking machine with an electrical low pressure impactor.

    Science.gov (United States)

    Li, Xiang; Kong, Haohui; Zhang, Xinying; Peng, Bin; Nie, Cong; Shen, Guanglin; Liu, Huimin

    2014-04-01

    Cigarette smoking is a particle-related exposure. Studying the characteristics of the particle size distribution of cigarette smoke can aid in providing knowledge of smoke aerosol attributes. We used an electrical low pressure impactor (ELPI) to measure the particle size distribution of mainstream cigarette smoke generated by a smoking machine and provided a continuum of particle sizes of cigarette smoke from a whole cigarette. The results showed that the aerodynamic diameters (D, geometric mean of a channel) of particles ranged from 0.021 to 1.956 μm, and the number concentrations were on the order of 10(5)-10(9) cm(-3) for different sizes of particles. The particle number of the size category below 0.1 μm approximated that of the category 0.1-2.0 μm, and the particles in the size category of 0.1-2.0 μm contributed extremely heavily to total particulate mass. In addition, the results with small samples indicated that the tar yields normalized per milligram of nicotine showed an approximately linear increase with increasing concentration of total particles. Copyright © 2014 The Research Centre for Eco-Environmental Sciences, Chinese Academy of Sciences. Published by Elsevier B.V. All rights reserved.

  11. Improving heat generation of magnetic nanoparticles by pre-orientation of particles in a static three tesla magnetic field

    Science.gov (United States)

    Beck, Mathias M.; Lammel, Christian; Gleich, Bernhard

    2017-04-01

    Inductive heating of electrically insulating materials like fiberglass reinforced thermoplastics (FRTP) without susceptors is not possible. However, due to their low thermal conductivity a volumetric heat generation method is advisable to reach short heating times to melt this material for reshaping. This can be done with magnetic nanoparticles as susceptors within the thermoplastic of the FRTP using Néel relaxation. During the heating process the particle's magnetic moment rotates with the field while the particle itself is fixed within the thermoplastic. Therefore the heat dissipation of each particle depends on its orientation within the field. To achieve the maximum heat generation of the particles we pre-oriented the particles within a plastic at the best angle to the applied AC field for induction. To do this, five mass percent nanoparticles were dispersed in an epoxy resin, which was then hardened at room temperature in a static three Tesla magnetic field. After its solidification the heating behavior of the sample was compared to a reference sample, which was hardened without a field. The oriented particles showed an increased heating rate when oriented parallel to the applied AC field. The absorption rate was 3.3 times as high as the undirected reference sample. When the alternating electromagnetic field was perpendicular to the oriented particles, the specific absorption rate was similar to that of the reference sample. We compare this result with theory and with calculations from literature, and conduct a numerical simulation.

  12. Connection of European particle therapy centers and generation of a common particle database system within the European ULICE-framework

    Directory of Open Access Journals (Sweden)

    Kessel Kerstin A

    2012-07-01

    Full Text Available Abstract Background To establish a common database on particle therapy for the evaluation of clinical studies integrating a large variety of voluminous datasets, different documentation styles, and various information systems, especially in the field of radiation oncology. Methods We developed a web-based documentation system for transnational and multicenter clinical studies in particle therapy. 560 patients have been treated from November 2009 to September 2011. Protons, carbon ions or a combination of both, as well as a combination with photons were applied. To date, 12 studies have been initiated and more are in preparation. Results It is possible to immediately access all patient information and exchange, store, process, and visualize text data, any DICOM images and multimedia data. Accessing the system and submitting clinical data is possible for internal and external users. Integrated into the hospital environment, data is imported both manually and automatically. Security and privacy protection as well as data validation and verification are ensured. Studies can be designed to fit individual needs. Conclusions The described database provides a basis for documentation of large patient groups with specific and specialized questions to be answered. Having recently begun electronic documentation, it has become apparent that the benefits lie in the user-friendly and timely workflow for documentation. The ultimate goal is a simplification of research work, better study analyses quality and eventually, the improvement of treatment concepts by evaluating the effectiveness of particle therapy.

  13. Connection of European particle therapy centers and generation of a common particle database system within the European ULICE-framework.

    Science.gov (United States)

    Kessel, Kerstin A; Bougatf, Nina; Bohn, Christian; Habermehl, Daniel; Oetzel, Dieter; Bendl, Rolf; Engelmann, Uwe; Orecchia, Roberto; Fossati, Piero; Pötter, Richard; Dosanjh, Manjit; Debus, Jürgen; Combs, Stephanie E

    2012-07-24

    To establish a common database on particle therapy for the evaluation of clinical studies integrating a large variety of voluminous datasets, different documentation styles, and various information systems, especially in the field of radiation oncology. We developed a web-based documentation system for transnational and multicenter clinical studies in particle therapy. 560 patients have been treated from November 2009 to September 2011. Protons, carbon ions or a combination of both, as well as a combination with photons were applied. To date, 12 studies have been initiated and more are in preparation. It is possible to immediately access all patient information and exchange, store, process, and visualize text data, any DICOM images and multimedia data. Accessing the system and submitting clinical data is possible for internal and external users. Integrated into the hospital environment, data is imported both manually and automatically. Security and privacy protection as well as data validation and verification are ensured. Studies can be designed to fit individual needs. The described database provides a basis for documentation of large patient groups with specific and specialized questions to be answered. Having recently begun electronic documentation, it has become apparent that the benefits lie in the user-friendly and timely workflow for documentation. The ultimate goal is a simplification of research work, better study analyses quality and eventually, the improvement of treatment concepts by evaluating the effectiveness of particle therapy.

  14. Cloning of an avian adeno-associated virus (AAAV) and generation of recombinant AAAV particles.

    Science.gov (United States)

    Bossis, Ioannis; Chiorini, John A

    2003-06-01

    Recent studies have proposed that adeno-associated viruses (AAVs) are not evolutionarily linked to other mammalian autonomous parvoviruses but are more closely linked to the autonomous parvoviruses of birds. To better understand the relationship between primate and avian AAVs (AAAVs), we cloned and sequenced the genome of an AAAV (ATCC VR-865) and generated recombinant AAAV particles. The genome of AAAV is 4,694 nucleotides in length and has organization similar to that of other AAVs. The entire genome of AAAV displays 56 to 65% identity at the nucleotide level with the other known AAVs. The AAAV genome has inverted terminal repeats of 142 nucleotides, with the first 122 forming the characteristic T-shaped palindromic structure. The putative Rep-binding element consists of a tandem (GAGY)(4) repeat, and the putative terminal resolution site (trs), CCGGT/CG, contains a single nucleotide substitution relative to the AAV(2) trs. The Rep open reading frame of AAAV displays 50 to 54% identity at the amino acid level with the other AAVs, with most of the diversity clustered at the carboxyl and amino termini. Comparison of the capsid proteins of AAAV and the primate dependoviruses indicate that divergent regions are localized to surface-exposed loops. Despite these sequence differences, we were able to produce recombinant AAAV particles carrying a lacZ reporter gene by cotransfection in 293T cells and were able to examine transduction efficiency in both chicken primary cells and several cell lines. Our findings indicate that AAAV is the most divergent AAV described to date but maintains all the characteristics unique to the genera of dependovirus.

  15. Investigate the complex process in particle-fluid based surface generation technology using reactive molecular dynamics method

    Science.gov (United States)

    Han, Xuesong; Li, Haiyan; Zhao, Fu

    2017-07-01

    Particle-fluid based surface generation process has already become one of the most important materials processing technology for many advanced materials such as optical crystal, ceramics and so on. Most of the particle-fluid based surface generation technology involves two key process: chemical reaction which is responsible for surface softening; physical behavior which is responsible for materials removal/deformation. Presently, researchers cannot give a reasonable explanation about the complex process in the particle-fluid based surface generation technology because of the small temporal-spatial scale and the concurrent influence of physical-chemical process. Molecular dynamics (MD) method has already been proved to be a promising approach for constructing effective model of atomic scale phenomenon and can serve as a predicting simulation tool in analyzing the complex surface generation mechanism and is employed in this research to study the essence of surface generation. The deformation and piles of water molecule is induced with the feeding of abrasive particle which justifies the property mutation of water at nanometer scale. There are little silica molecule aggregation or materials removal because the water-layer greatly reduce the strength of mechanical interaction between particle and materials surface and minimize the stress concentration. Furthermore, chemical effect is also observed at the interface: stable chemical bond is generated between water and silica which lead to the formation of silconl and the reaction rate changes with the amount of water molecules in the local environment. Novel ring structure is observed in the silica surface and it is justified to be favored of chemical reaction with water molecule. The siloxane bond formation process quickly strengthened across the interface with the feeding of abrasive particle because of the compressive stress resulted by the impacting behavior.

  16. Investigate the complex process in particle-fluid based surface generation technology using reactive molecular dynamics method

    Directory of Open Access Journals (Sweden)

    Xuesong Han

    2017-07-01

    Full Text Available Particle-fluid based surface generation process has already become one of the most important materials processing technology for many advanced materials such as optical crystal, ceramics and so on. Most of the particle-fluid based surface generation technology involves two key process: chemical reaction which is responsible for surface softening; physical behavior which is responsible for materials removal/deformation. Presently, researchers cannot give a reasonable explanation about the complex process in the particle-fluid based surface generation technology because of the small temporal-spatial scale and the concurrent influence of physical-chemical process. Molecular dynamics (MD method has already been proved to be a promising approach for constructing effective model of atomic scale phenomenon and can serve as a predicting simulation tool in analyzing the complex surface generation mechanism and is employed in this research to study the essence of surface generation. The deformation and piles of water molecule is induced with the feeding of abrasive particle which justifies the property mutation of water at nanometer scale. There are little silica molecule aggregation or materials removal because the water-layer greatly reduce the strength of mechanical interaction between particle and materials surface and minimize the stress concentration. Furthermore, chemical effect is also observed at the interface: stable chemical bond is generated between water and silica which lead to the formation of silconl and the reaction rate changes with the amount of water molecules in the local environment. Novel ring structure is observed in the silica surface and it is justified to be favored of chemical reaction with water molecule. The siloxane bond formation process quickly strengthened across the interface with the feeding of abrasive particle because of the compressive stress resulted by the impacting behavior.

  17. Sub-micron Cu/SSZ-13: Synthesis and application as selective catalytic reduction (SCR) catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Prodinger, Sebastian; Derewinski, Miroslaw A.; Wang, Yilin; Washton, Nancy M.; Walter, Eric D.; Szanyi, János; Gao, Feng; Wang, Yong; Peden, Charles H. F.

    2017-02-01

    For the first time, sub-micron Cu/SSZ-13, obtained by modifying an existing synthesis procedure, was shown to be an effective and stable catalyst for selective catalytic reduction reactions, such as NO reduction. Characterization of the materials with X-ray diffraction, N2-physisorption and 27Al MAS NMR shows that hydrothermal aging, simulating SCR reaction conditions, is more destructive in respect to dealumination for smaller particles prior to Cu-exchange. However, the catalytic performance and hydrothermal stability for Cu/SSZ-13 is independent of the particle size. In particular, the stability of tetrahedral framework Al is improved in the sub-micron Cu/SSZ-13 catalysts of comparable Cu loading. This indicates that variations in the Al distribution for different SSZ-13 synthesis procedures have a more critical influence on stabilizing isolated Cu-ions during harsh hydrothermal aging than the particle size. This study is of high interest for applications in vehicular DeNOx technologies where high loadings of active species on wash coats can be achieved by using sub-micron Cu/SSZ-13. The authors would like to thank B. W. Arey and J. J. Ditto for performing electron microscope imaging. The authors gratefully acknowledge the US Department of Energy (DOE), Energy Efficiency and Renewable Energy, Vehicle Technologies Office for the support of this work. S. P and M. A. D also acknowledge support by the Materials Synthesis and Simulation Across Scales (MS3 Initiative) conducted under the Laboratory Directed Research & Development Program at PNNL. The research described in this paper was performed in the Environmental Molecular Sciences Laboratory (EMSL), a national scientific user facility sponsored by the DOE’s Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory (PNNL). PNNL is operated for the US DOE by Battelle.

  18. Liquefaction of coals using ultra-fine particle, unsupported catalysts: In situ particle generation by rapid expansion of supercritical fluid solutions. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    The research conducted by Textron Defense Systems (TDS) represents a potential new and innovative concept for dispersed coal liquefaction. The technical approach is generation of ultra-fine catalyst particles from supercritical solutions by rapid expansion of either catalyst only, or mixtures of catalyst and coal material in supersaturated solvents. The process of rapid expansion of supercritical fluid solutions was developed at Battelle`s Pacific Northwest Laboratories for the intended purpose of providing a new analytical technique for characterizing supercritical fluids. The concept forming the basis of this research is that ultra-fine particles can be generated from supercritical solutions by rapid expansion of either catalyst or catalyst/coal-material mixtures in supersaturated solvents, such as carbon dioxide or water. The focal point of this technique is the rapid transfer of low vapor pressure solute (i.e., catalyst), dissolved in the supercritical fluid solvent, to the gas phase as the solution is expanded through an orifice. The expansion process is characterized by highly nonequilibrium conditions which cause the solute to undergo extremely rapid supersaturation with respect to the solvent, leading to nucleation and particle growth resulting in nanometer size catalyst particles. A supercritical expansion system was designed and built by TDS at their Haverhill facility.

  19. Resuspension of coal and coal/municipal sewage sludge combustion generated fine particles for inhalation health effects studies

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, Art; Wendt, Jost O.L. [Department of Chemical and Environmental Engineering, University of Arizona, 85721 Tucson, AZ (United States); Cenni, Roberta [Institut fuer Verfahrenstechnik und Dampfkesselwesen, Universitaet Stuttgart, Stuttgart (Germany); Young, R. Scott; Witten, Mark L. [Lung Injury Laboratory, Department of Pediatrics, Arizona Health Sciences Center, 85721 Tucson, AZ (United States)

    2002-03-27

    Airborne particulate matter (PM) is an important environmental issue because of its association with acute respiratory distress in humans, although the specific particle characteristics that cause lung damage have yet to be identified. Particle size, acid aerosols, water-soluble transition metals (e.g. Cu, Fe, V, Ni and Zn), polyaromatic hydrocarbons, and particle composition are the focus of several popular hypotheses addressing respiratory distress. All of the above mentioned characteristics are contained in PM generated from the combustion of both pulverized coal, and biomass, including dried municipal sewage sludge (MSS). In this investigation, we report results from collaborative interdisciplinary research on the inhalation health risks caused by particles emitted from the co-combustion of municipal sewage sludge (MSS) and coal. A solid particle resuspension system was implemented to resuspend ash particles. Mice were exposed to resuspended coal and MSS/coal ash particles. Mice exposed to MSS/coal ash particulate demonstrated significant increases in lung permeability, a marker of the early stages of pathological lung injury, while the mice exposed to coal-only ash did not. These results show that the composition of particles actually inhaled is important in determining lung damage. Zinc was significantly more concentrated in the MSS/coal ash than coal ash particles and the pH of these particles did not differ significantly. Specifically, an MSS/coal mixture, when burned, emits particles that may cause significantly more lung damage than coal alone, and that consequently, the use of MSS as a 'green', CO{sub 2}-neutral replacement fuel should be carefully considered.

  20. Improving heat generation of magnetic nanoparticles by pre-orientation of particles in a static three tesla magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Beck, Mathias M., E-mail: Mathias.Beck@tum.de [Institute for Machine Tools and Industrial Management, Technical University of Munich, Boltzmannstr. 15, 85748 Garching (Germany); Lammel, Christian [Institute for Machine Tools and Industrial Management, Technical University of Munich, Boltzmannstr. 15, 85748 Garching (Germany); Gleich, Bernhard [Institute of Medical Engineering, Technical University of Munich, Boltzmannstr. 11, 85748 Garching (Germany)

    2017-04-01

    Inductive heating of electrically insulating materials like fiberglass reinforced thermoplastics (FRTP) without susceptors is not possible. However, due to their low thermal conductivity a volumetric heat generation method is advisable to reach short heating times to melt this material for reshaping. This can be done with magnetic nanoparticles as susceptors within the thermoplastic of the FRTP using Néel relaxation. During the heating process the particle's magnetic moment rotates with the field while the particle itself is fixed within the thermoplastic. Therefore the heat dissipation of each particle depends on its orientation within the field. To achieve the maximum heat generation of the particles we pre-oriented the particles within a plastic at the best angle to the applied AC field for induction. To do this, five mass percent nanoparticles were dispersed in an epoxy resin, which was then hardened at room temperature in a static three Tesla magnetic field. After its solidification the heating behavior of the sample was compared to a reference sample, which was hardened without a field. The oriented particles showed an increased heating rate when oriented parallel to the applied AC field. The absorption rate was 3.3 times as high as the undirected reference sample. When the alternating electromagnetic field was perpendicular to the oriented particles, the specific absorption rate was similar to that of the reference sample. We compare this result with theory and with calculations from literature, and conduct a numerical simulation. - Highlights: • Magnetic nanoparticles are aligned using a static three tesla magnetic field. • Inductive heating depends on the particles pre-orientation in a solid matrix. • Alignment increases the heat generation significantly.

  1. Stochastic Trajectory Generation Using Particle Swarm Optimization for Quadrotor Unmanned Aerial Vehicles (UAVs

    Directory of Open Access Journals (Sweden)

    Babak Salamat

    2017-05-01

    Full Text Available The aim of this paper is to provide a realistic stochastic trajectory generation method for unmanned aerial vehicles that offers a tool for the emulation of trajectories in typical flight scenarios. Three scenarios are defined in this paper. The trajectories for these scenarios are implemented with quintic B-splines that grant smoothness in the second-order derivatives of Euler angles and accelerations. In order to tune the parameters of the quintic B-spline in the search space, a multi-objective optimization method called particle swarm optimization (PSO is used. The proposed technique satisfies the constraints imposed by the configuration of the unmanned aerial vehicle (UAV. Further particular constraints can be introduced such as: obstacle avoidance, speed limitation, and actuator torque limitations due to the practical feasibility of the trajectories. Finally, the standard rapidly-exploring random tree (RRT* algorithm, the standard (A* algorithm and the genetic algorithm (GA are simulated to make a comparison with the proposed algorithm in terms of execution time and effectiveness in finding the minimum length trajectory.

  2. Generation of excited coherent states for a charged particle in a uniform magnetic field

    Energy Technology Data Exchange (ETDEWEB)

    Mojaveri, B., E-mail: bmojaveri@azaruniv.ac.ir [Department of Physics, Azarbaijan Shahid Madani University, P.O. Box 51745-406, Tabriz (Iran, Islamic Republic of); Dehghani, A., E-mail: a-dehghani@tabrizu.ac.ir, E-mail: alireza.dehghani@gmail.com [Department of Physics, Payame Noor University, P.O. Box 19395-3697, Tehran (Iran, Islamic Republic of)

    2015-04-15

    We introduce excited coherent states, |β,α;nгЂ‰≔a{sup †n}|β,αгЂ‰, where n is an integer and states |β,αгЂ‰ denote the coherent states of a charged particle in a uniform magnetic field. States |β,αгЂ‰ minimize the Schrödinger-Robertson uncertainty relation while having the nonclassical properties. It has been shown that the resolution of identity condition is realized with respect to an appropriate measure on the complex plane. Some of the nonclassical features such as sub-Poissonian statistics and quadrature squeezing of these states are investigated. Our results are compared with similar Agarwal’s type photon added coherent states (PACSs) and it is shown that, while photon-counting statistics of |β,α,nгЂ‰ are the same as PACSs, their squeezing properties are different. It is also shown that for large values of |β|, while they are squeezed, they minimize the uncertainty condition. Additionally, it has been demonstrated that by changing the magnitude of the external magnetic field, B{sub ext}, the squeezing effect is transferred from one component to another. Finally, a new scheme is proposed to generate states |β,α;nгЂ‰ in cavities. .

  3. Submicron Emulsions and Their Applications in Oral Delivery.

    Science.gov (United States)

    Mundada, Veenu; Patel, Mitali; Sawant, Krutika

    2016-01-01

    A "submicron emulsion" is an isotropic mixture of drug, lipids, and surfactants, usually with hydrophilic cosolvents and with droplet diameters ranging from 10 to 500 nm. Submicron emulsions are of increasing interest in medicine due to their kinetic stability, high solubilizing capacity, and tiny globule size. Because of these properties, they have been applied in various fields, such as personal care, cosmetics, health care, pharmaceuticals, and agrochemicals. Submicron emulsions are by far the most advanced nanoparticulate systems for the systemic delivery of biologically active agents for controlled drug delivery and targeting. They are designed mainly for pharmaceutical formulations suitable for various routes of administration like parenteral, ocular, transdermal, and oral. This review article describes the marked potential of submicron emulsions for oral drug delivery owing to their numerous advantages like reduced first pass metabolism, inhibition of P-glycoprotein efflux system, and enhanced absorption via intestinal lymphatic pathway. To overcome the limitations of liquid dosage forms, submicron emulsions can be formulated into solid dosage forms such as solid self-emulsifying systems. This article covers various types of submicron emulsions like microemulsion, nanoemulsion, and self-emulsifying drug delivery system (SEDDS), and their potential pharmaceutical applications in oral delivery with emphasis on their advantages, limitations, and advancements.

  4. Submicron Features in Higher Manganese Silicide

    Directory of Open Access Journals (Sweden)

    Yatir Sadia

    2013-01-01

    Full Text Available The world energy crisis had increased the demand for alternative energy sources and as such is one of the topics at the forefront of research. One way for reducing energy consumption is by thermoelectricity. Thermoelectric effects enable direct conversion of thermal into electrical energy. Higher manganese silicide (HMS, MnSi1.75 is one of the promising materials for applications in the field of thermoelectricity. The abundance and low cost of the elements, combined with good thermoelectric properties and high mechanical and chemical stability at high temperatures, make it very attractive for thermoelectric applications. Recent studies have shown that Si-rich HMS has improved thermoelectric properties. The most interesting of which is the unusual reduction in thermal conductivity. In the current research, transmission (TEM and scanning (SEM electron microscopy as well as X-ray diffraction methods were applied for investigation of the govern mechanisms resulting in very low thermal conductivity values of an Si-rich HMS composition, following arc melting and hot-pressing procedures. In this paper, it is shown that there is a presence of sub-micron dislocations walls, stacking faults, and silicon and HMS precipitates inside each other apparent in the matrix, following a high temperature (0.9 Tm hot pressing for an hour. These are not just responsible for the low thermal conductivity values observed but also indicate the ability to create complicate nano-structures that will last during the production process and possibly during the application.

  5. Particle dynamics in self-generated dunes over a range of hydraulic and sediment transport conditions using LES--DEM

    CERN Document Server

    Sun, Rui; Strom, Kyle

    2016-01-01

    Direct measurement of vertical and longitudinal sediment fluxes on migrating sandy bedforms are extremely difficult to perform in both the field and laboratory. In this study we use the LES--DEM (large eddy simulation--discrete element method) solver SediFoam to examine the individual particle motions and resulting fluxes in a domain of self-generated dunes. In SediFoam, the motions of, and collisions among, the sediment grains as well as their interactions with surrounding turbulent flows are resolved. The numerical simulations are performed over a range of transport settings, spanning bedform inception through washout conditions, to examine the individual particle dynamics. The space-time evolution of dune surfaces is demonstrated. The self-generated dunes are stable at relatively low Reynolds numbers, but then become increasingly unstable at higher Reynolds numbers; eventually washing out as the number of bypass grains and particles in suspension increase. Data from the simulation are used to examine the v...

  6. Vectors and submicron precision: redundancy and 3D stacking in silicon pixel detectors

    CERN Document Server

    Heijne, E H M; Wong, W; Idarraga, J; Visser, J; Jakubek, J; Leroy, C; Turecek, D; Visschers, J; Pospisil, S; Ballabriga, R; Vykydal, Z; Vermeulen, J; Plackett, R; Heijne, E H M; Llopart, X; Boltje, D; Campbell, M

    2010-01-01

    Measurements are shown of GeV pions and muons in two 300 mu m thick, Si Medipix pixel detector assemblies that are stacked on top of each other, with a 25 mu m thick brass foil in between. In such a radiation imaging semiconductor matrix with a large number of pixels along the particle trail, one can determine local space vectors for the particle trajectory instead of points. This improves pattern recognition and track reconstruction, especially in a crowded environment. Stacking of sensor planes is essential for resolving directional ambiguities. Signal charge sharing can be employed for measuring positions with submicron precision. In the measurements one notices accompanying `delta' electrons that emerge outside the particle trail, far beyond the boundaries of the 55 mu m pixel cells. The frequency of such corrupted position measurements is similar to one per 2.5mm of traversed Si.

  7. Size-Resolved Characterization of Particles and Fibers Released during Abrasion of Fiber-Reinforced Composite in a Workplace Influenced by Ambient Background Sources

    DEFF Research Database (Denmark)

    Kling, Kirsten I.; Levin, Marcus; Jensen, Alexander C. O.

    2016-01-01

    We demonstrate the use of high-to low-resolution microscopy and particle chemical analysis during normal vacuum and cryo-conditions to identify the nature and relative abundances of process-generated particles and fibers from sanding of a glass and carbon fiber epoxy layer-composite in a workplace...... of ambient particles to the background in the production facility was observed in the sub-micron size range. Fibers are posing a dominant exposure risk in the micron size range, with carbon fibers dominating in count....

  8. Introducing asymmetric functionality into MOFs via the generation of metallic Janus MOF particles.

    Science.gov (United States)

    Ayala, Abraham; Carbonell, Carlos; Imaz, Inhar; Maspoch, Daniel

    2016-04-14

    Herein we report a versatile methodology for engineering metallic Janus MOF particles based on desymmetrization at interfaces, whereby each MOF particle is partially coated with a desired metal. We demonstrate that it enables the fabrication of homogeneous Janus MOF particles according to the MOF (ZIF-8, UiO-66 or UiO-66-SH), the metal (Au, Co or Pt), the MOF particle size (from the micrometer to the submicrometer regime) and the metal-film thickness (from 5 nm to 50 nm) employed. We anticipate that our strategy could be applied to impart new functionalities to MOFs, including asymmetric functionalization, magnetic-guidance and motorization.

  9. X, Ku-band microwave-absorption properties of polyarylene ether nitriles terminated with phthalonitrile/Fe{sub 3}O{sub 4} hybrid submicron spheres

    Energy Technology Data Exchange (ETDEWEB)

    Tong, Lifen, E-mail: 361626614@qq.com; Pu, Zejun; Huang, Xu; Liu, Xiaobo, E-mail: liuxb@uestc.edu.cn

    2014-05-01

    Highlights: • PEN-t-Ph/Fe{sub 3}O{sub 4} hybrid spheres were prepared via one-step solvothermal method. • Polymer compatibility is introduced into inorganic submicron spheres successfully. • PEN-t-Ph/Fe{sub 3}O{sub 4} hybrid submicron spheres possessed good ferrimagnetism. • Control the microwave absorption band of PEN-t-Ph/Fe{sub 3}O{sub 4} hybrid submicron spheres. - Abstract: A novel series of PEN-t-Ph/Fe{sub 3}O{sub 4} hybrid submicron spheres with different additions of PEN-t-Ph have been prepared successfully via solvothermal method, and their structures and morphologies were characterized by X-ray powder diffraction (XRD), energy dispersive spectrometer (EDS), Fourier transform infrared spectrophotometer (FTIR), and scanning electron microscopy (SEM). The results revealed that the crystallinity, dispersity, and size of hybrid submicron spheres can be controlled by altering the addition content of PEN-t-Ph. Magnetization measurement showed that the PEN-t-Ph/Fe{sub 3}O{sub 4} hybrid submicron spheres possessed good ferrimagnetism. The electromagnetic measurement indicated that the resonance peaks of complex permittivity, complex permeability, dielectric loss, and magnetic loss were shifted to the higher frequency as the addition of PEN-t-Ph increased. Moreover, the microwave absorption band was also shifted to higher frequency as the addition of PEN-t-Ph increased. Through this method, the polymer compatibility can be introduced into inorganic submicron spheres, which could provide the inorganic particles with more applications.

  10. Generation and characterization of large-particle aerosols using a center flow tangential aerosol generator with a non-human-primate, head-only aerosol chamber.

    Science.gov (United States)

    Bohannon, J Kyle; Lackemeyer, Matthew G; Kuhn, Jens H; Wada, Jiro; Bollinger, Laura; Jahrling, Peter B; Johnson, Reed F

    2015-01-01

    Aerosol droplets or particles produced from infected respiratory secretions have the potential to infect another host through inhalation. These respiratory particles can be polydisperse and range from 0.05 to 500 µm in diameter. Animal models of infection are generally established to facilitate the potential licensure of candidate prophylactics and/or therapeutics. Consequently, aerosol-based animal infection models are needed to properly study and counter airborne infections. Ideally, experimental aerosol exposure should reliably result in animal disease that faithfully reproduces the modeled human disease. Few studies have been performed to explore the relationship between exposure particle size and induced disease course for infectious aerosol particles. The center flow tangential aerosol generator (CenTAG™) produces large-particle aerosols capable of safely delivering a variety of infectious aerosols to non-human primates (NHPs) within a Class III Biological Safety Cabinet (BSC) for establishment or refinement of NHP infectious disease models. Here, we report the adaptation of this technology to the Animal Biosafety Level 4 (ABSL-4) environment for the future study of high-consequence viral pathogens and the characterization of CenTAG™-created sham (no animal, no virus) aerosols using a variety of viral growth media and media supplements.

  11. Generation and characterization of large-particle aerosols using a center flow tangential aerosol generator with a nonhuman-primate, head-only aerosol chamber

    Science.gov (United States)

    Bohannon, J. Kyle; Lackemeyer, Matthew G.; Kuhn, Jens H.; Wada, Jiro; Bollinger, Laura; Jahrling, Peter B.; Johnson, Reed F.

    2016-01-01

    Aerosol droplets or particles produced from infected respiratory secretions have the potential to infect another host through inhalation. These respiratory particles can be polydisperse and range from 0.05–500 μm in diameter. Animal models of infection are generally established to facilitate the potential licensure of candidate prophylactics and/or therapeutics. Consequently, aerosol-based animal infection models are needed to properly study and counter airborne infections. Ideally, experimental aerosol exposure should reliably result in animal disease that faithfully reproduces the modelled human disease. Few studies have been performed to explore the relationship between exposure particle size and induced disease course for infectious aerosol particles. The center flow tangential aerosol generator (CenTAG™) produces large-particle aerosols capable of safely delivering a variety of infectious aerosols to nonhuman primates within a Class III Biological Safety Cabinet (BSC) for establishment or refinement of nonhuman primate infectious disease models. Here we report the adaptation of this technology to the Animal Biosafety Level 4 (ABSL-4) environment for the future study of high-consequence viral pathogens and the characterization of CenTAG™-created sham (no animal, no virus) aerosols using a variety of viral growth media and media supplements. PMID:25970823

  12. Intermittent contact of fluidized anode particles containing exoelectrogenic biofilms for continuous power generation in microbial fuel cells

    KAUST Repository

    Liu, Jia

    2014-09-01

    Current generation in a microbial fuel cell can be limited by the amount of anode surface area available for biofilm formation, and slow substrate degradation kinetics. Increasing the anode surface area can increase the amount of biofilm, but performance will improve only if the anode material is located near the cathode to minimize solution internal resistance. Here we demonstrate that biofilms do not have to be in constant contact with the anode to produce current in an MFC. Granular activated carbon particles enriched with exoelectrogenic biofilm are fluidized (by stirring) in the anode chamber of the MFC, resulting in only intermittent contact between the particles and the anode current collector. The maximum power density generated is 951 ± 10 mW m-2, compared to 813 ± 2 mW m-2 for the control without stirring (packed bed), and 525 ± 1 mW m-2 in the absence of GAC particles and without stirring. GAC-biofilm particles demonstrate capacitor-like behavior, but achieve nearly constant discharge conditions due to the large number of particles that contact the current collector. These results provide proof of concept for the development of flowable electrode reactors, where anode biofilms can be electrically charged in a separate storage tank and then rapidly discharged in compact anode chambers. © 2014 Elsevier B.V. All rights reserved.

  13. Cell viability, collagen synthesis and cytokine expression in human osteoblasts following incubation with generated wear particles using different bone cements.

    Science.gov (United States)

    Schulze, Christoph; Lochner, Katrin; Jonitz, Anika; Lenz, Robert; Duettmann, Oliver; Hansmann, Doris; Bader, Rainer

    2013-07-01

    In total hip arthroplasty, wear particles generated at articulating surfaces and interfaces between bone, cement and implants have a negative impact on osteoblasts, leading to osteolysis and implant loosening. The aim of this experimental study was to determine the effects of particulate wear debris generated at the interface between straight stainless steel hip stems (Exeter(®)) and three different bone cements (Palacos(®) R, Simplex™ P and Cemex(®) Genta) on cell viability, collagen synthesis and cytokine expression in human osteoblasts. Primary osteoblasts were treated with various concentrations of wear particles. The synthesis of procollagen type I and different cytokines was analysed, and markers for apoptosis and necrosis were also detected. The cytokine synthesis rates in the osteoblasts were initially increased and varied, depending on incubation time and particle concentration. Specific differences in the synthesis rates of interleukin (IL)‑6, IL-8, vascular endothelial growth factor (VEGF) and monocyte chemotactic protein-1 (MCP-1) were observed with the different bone cements examined. The negative effect of the particles on the synthesis of procollagen type I and increased rates of cell apoptosis and necrosis were observed with all three cements analysed. Our present data suggest that wear particles from the interface between the total hip stem and bone cement have a significant effect on viability, cytokine expression and collagen synthesis in human osteoblasts, depending on the bone cement used.

  14. Single Wall Diesel Particulate Filter (DPF) Filtration Efficiency Studies Using Laboratory Generated Particles

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Juan; Stewart, Marc; Maupin, Gary D.; Herling, Darrell R.; Zelenyuk, Alla

    2009-04-15

    Diesel offers higher fuel efficiency, but produces higher exhaust particulate matter. Diesel particulate filters are presently the most efficient means to reduce these emissions. These filters typically trap particles in two basic modes: at the beginning of the exposure cycle the particles are captured in the filter holes, and at longer times the particles form a "cake" on which particles are trapped. Eventually the "cake" removed by oxidation and the cycle is repeated. We have investigated the properties and behavior of two commonly used filters: silicon carbide (SiC) and cordierite (DuraTrap® RC) by exposing them to nearly-spherical ammonium sulfate particles. We show that the transition from deep bed filtration to "cake" filtration can easily be identified by recording the change in pressure across the filters as a function of exposure. We investigated performance of these filters as a function of flow rate and particle size. The filters trap small and large particles more efficiently than particles that are ~80 to 200 nm in aerodynamic diameter. A comparison between the experimental data and a simulation using incompressible lattice-Boltzmann model shows very good qualitative agreement, but the model overpredicts the filter’s trapping efficiency.

  15. Performance of peanut mutants and their offspring generated from mixed high-energy particle field radiation and tissue culture.

    Science.gov (United States)

    Wang, J S; Qiao, L X; Zhao, L S; Wang, P; Guo, B T; Liu, L X; Sui, J M

    2015-09-09

    To develop new ways to breed peanut, we irradiated seeds of the Luhua 11 cultivar with a mixed high-energy particle field at different doses. The embryonic leaflets were extracted as explants and incubated on somatic embryo induction medium and then on somatic embryo germination and regeneration medium. After being grafted, the M1-generation plants were transplanted, and seeds from each M1-generation plant were harvested. In the following year, the M2-generation seeds were planted separately. Some M2-generation plants showed distinct character segregation relative to the mutagenic parent in terms of vigor, fertility, plant height, branch number, and pod size and shape. M2-generation plants that had a high pod weight per plant tended to produce M3-generation offspring that also had a high pod weight per plant, much higher than that of the mutagenic parent, Luhua 11. M4-generation seeds varied greatly in quality, and 35 individuals with an increased fat content (>55%) were obtained. Overall, the results indicate that the combination of mutagenesis via mixed high-energy particle field exposure and tissue culture is promising for peanut breeding.

  16. Formation characteristics of aerosol particles from pulverized coal pyrolysis in high-temperature environments.

    Science.gov (United States)

    Chen, Wei-Hsin; Du, Shan-Wen; Yang, Hsi-Hsien; Wu, Jheng-Syun

    2008-05-01

    The formation characteristics of aerosol particles from pulverized coal pyrolysis in high temperatures are studied experimentally. By conducting a drop-tube furnace, fuel pyrolysis processes in industrial furnaces are simulated in which three different reaction temperatures of 1000, 1200, and 1400 degrees C are considered. Experimental observations indicate that when the reaction temperature is 1000 degrees C, submicron particles are produced, whereas the particle size is dominated by nanoscale for the temperature of 1400 degrees C. Thermogravimetric analysis of the aerosol particles stemming from the pyrolysis temperature of 1000 degrees C reveals that the thermal behavior of the aerosol is characterized by a three-stage reaction with increasing heating temperature: (1) a volatile-reaction stage, (2) a weak-reaction stage, and (3) a soot-reaction stage. However, with the pyrolysis temperature of 1400 degrees C, the volatile- and weak-reaction stages almost merge together and evolve into a chemical-frozen stage. The submicron particles (i.e., 1000 degrees C) are mainly composed of volatiles, tar, and soot, with the main component of the nanoscale particles (i.e., 1400 degrees C) being soot. The polycyclic aromatic hydrocarbons (PAHs) contained in the aerosols are also analyzed. It is found that the PAH content in generated aerosols decreases dramatically as the pyrolysis temperature increases.

  17. Characterization of airborne particles generated from metal active gas welding process.

    Science.gov (United States)

    Guerreiro, C; Gomes, J F; Carvalho, P; Santos, T J G; Miranda, R M; Albuquerque, P

    2014-05-01

    This study is focused on the characterization of particles emitted in the metal active gas welding of carbon steel using mixture of Ar + CO2, and intends to analyze which are the main process parameters that influence the emission itself. It was found that the amount of emitted particles (measured by particle number and alveolar deposited surface area) are clearly dependent on the distance to the welding front and also on the main welding parameters, namely the current intensity and heat input in the welding process. The emission of airborne fine particles seems to increase with the current intensity as fume-formation rate does. When comparing the tested gas mixtures, higher emissions are observed for more oxidant mixtures, that is, mixtures with higher CO2 content, which result in higher arc stability. These mixtures originate higher concentrations of fine particles (as measured by number of particles by cm(3) of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more severe worker's exposure.

  18. Heterogeneous Oxidation of Laboratory-generated Mixed Composition and Biomass Burning Particles

    Science.gov (United States)

    Lim, C. Y.; Sugrue, R. A.; Hagan, D. H.; Cappa, C. D.; Kroll, J. H.; Browne, E. C.

    2016-12-01

    Heterogeneous oxidation of organic aerosol (OA) can significantly transform the chemical and physical properties of particulate matter in the atmosphere, leading to changes to the chemical composition of OA and potential volatilization of organic compounds. It has become increasingly apparent that the heterogeneous oxidation kinetics of OA depend on the phase and morphology of the particles. However, most laboratory experiments to date have been performed on single-component, purely organic precursors, which may exhibit fundamentally different behavior than more complex particles in the atmosphere. Here we present laboratory studies of the heterogeneous oxidation of two more complex chemical systems: thin, organic coatings on inorganic seed particles and biomass burning OA. In the first system, squalane (C30H62), a model compound for reduced OA, is coated onto dry ammonium sulfate particles at various thicknesses (10-20 nm) and exposed to hydroxyl radical (OH) in a flow tube reactor. In the second, we use a semi-batch reactor to study the heterogeneous OH-initiated oxidation of biomass burning particles as a part of the 2016 FIREX campaign in Missoula, MT. The resulting changes in chemical composition are monitored with an Aerodyne High Resolution Time-of-flight Aerosol Mass Spectrometer (AMS) and a soot-particle AMS for the non-refractory and refractory systems, respectively. We show that the heterogeneous oxidation kinetics of these multicomponent particles are substantially different than that of the single-component particles. The oxidation of organic coatings is rapid, undergoing dramatic changes to carbon oxidation state and losing a significant amount of organic mass after relatively low OH exposures (equivalent to several days of atmospheric processing). In the case of biomass burning particles, the kinetics are complex, with different components (inferred by aerosol mass spectrometry) undergoing oxidation at different rates.

  19. Investigation of the enhanced spatial density of submicron lunar ejecta between L values 1.2 and 3.0 in the earth's magnetosphere: Theory

    Science.gov (United States)

    Alexander, W. M.; Tanner, W. G.; Goad, H. S.

    1987-01-01

    Initial results from the measurement conducted by the dust particle experiment on the lunar orbiting satellite Lunar Explorer 35 (LE 35) were reported with the data interpreted as indicating that the moon is a significant source of micrometeroids. Primary sporadic and stream meteoroids impacting the surface of the moon at hypervelocity was proposed as the source of micron and submicron particles that leave the lunar craters with velocities sufficient to escape the moon's gravitational sphere of influence. No enhanced flux of lunar ejecta with masses greater than a nanogram was detected by LE 35 or the Lunar Orbiters. Hypervelocity meteoroid simulation experiments concentrating on ejecta production combined with extensive analyses of the orbital dynamics of micron and submicron lunar ejecta in selenocentric, cislunar, and geocentric space have shown that a pulse of these lunar ejecta, with a time correlation relative to the position of the moon relative to the earth, intercepts the earth's magnetopause surface (EMPs). As shown, a strong reason exists for expecting a significant enhancement of submicron dust particles in the region of the magnetosphere between L values of 1.2 and 3.0. This is the basis for the proposal of a series of experiments to investigate the enhancement or even trapping of submicron lunar ejecta in this region. The subsequent interaction of this mass with the upper-lower atmosphere of the earth and possible geophysical effects can then be studied.

  20. Comparison of deposited surface area of airborne ultrafine particles generated from two welding processes.

    Science.gov (United States)

    Gomes, J F; Albuquerque, P C; Miranda, Rosa M; Santos, Telmo G; Vieira, M T

    2012-09-01

    This article describes work performed on the assessment of the levels of airborne ultrafine particles emitted in two welding processes metal-active gas (MAG) of carbon steel and friction-stir welding (FSW) of aluminium in terms of deposited area in alveolar tract of the lung using a nanoparticle surface area monitor analyser. The obtained results showed the dependence from process parameters on emitted ultrafine particles and clearly demonstrated the presence of ultrafine particles, when compared with background levels. The obtained results showed that the process that results on the lower levels of alveolar-deposited surface area is FSW, unlike MAG. Nevertheless, all the tested processes resulted in important doses of ultrafine particles that are to be deposited in the human lung of exposed workers.

  1. Electrospun submicron bioactive glass fibers for bone tissue scaffold.

    Science.gov (United States)

    Lu, H; Zhang, T; Wang, X P; Fang, Q F

    2009-03-01

    Submicron bioactive glass fibers 70S30C (70 mol% SiO(2), 30 mol% CaO) acting as bone tissue scaffolds were fabricated by electrospinning method. The scaffold is a hierarchical pore network that consists of interconnected fibers with macropores and mesopores. The structure, morphological characterization and mechanical properties of the submicron bioactive glass fibers were studied by XRD, EDS, FIIR, SEM, N(2) gas absorption analyses and nanoindentation. The effect of the voltage on the morphology of electrospun bioactive glass fibers was investigated. It was found that decreasing the applied voltage from 19 to 7 kV can facilitate the formation of finer fibers with fewer bead defects. The hardness and Young's modulus of submicron bioactive glass fibers were measured as 0.21 and 5.5 GPa, respectively. Comparing with other bone tissue scaffolds measured by nanoindentation, the elastic modulus of the present scaffold was relatively high and close to the bone.

  2. NATO Advanced Study Institute on Physics of Submicron Semiconductor Devices

    CERN Document Server

    Ferry, David; Jacoboni, C

    1988-01-01

    The papers contained in the volume represent lectures delivered as a 1983 NATO ASI, held at Urbino, Italy. The lecture series was designed to identify the key submicron and ultrasubmicron device physics, transport, materials and contact issues. Nonequilibrium transport, quantum transport, interfacial and size constraints issues were also highlighted. The ASI was supported by NATO and the European Research Office. H. L. Grubin D. K. Ferry C. Jacoboni v CONTENTS MODELLING OF SUB-MICRON DEVICES.................. .......... 1 E. Constant BOLTZMANN TRANSPORT EQUATION... ... ...... .................... 33 K. Hess TRANSPORT AND MATERIAL CONSIDERATIONS FOR SUBMICRON DEVICES. . .. . . . . .. . . . .. . .. . .... ... .. . . . .. . . . .. . . . . . . . . . . 45 H. L. Grubin EPITAXIAL GROWTH FOR SUB MICRON STRUCTURES.................. 179 C. E. C. Wood INSULATOR/SEMICONDUCTOR INTERFACES.......................... 195 C. W. Wilms en THEORY OF THE ELECTRONIC STRUCTURE OF SEMICONDUCTOR SURFACES AND INTERFACES...................

  3. Study of particle size distribution and formation mechanism of radioactive aerosols generated in high-energy neutron fields

    CERN Document Server

    Endo, A; Noguchi, H; Tanaka, S; Iida, T; Furuichi, S; Kanda, Y; Oki, Y

    2003-01-01

    The size distributions of sup 3 sup 8 Cl, sup 3 sup 9 Cl, sup 8 sup 2 Br and sup 8 sup 4 Br aerosols generated by irradiations of argon and krypton gases containing di-octyl phthalate (DOP) aerosols with 45 MeV and 65 MeV quasi-monoenergetic neutrons were measured in order to study the formation mechanism of radioactive particles in high energy radiation fields. The effects of the size distribution of the radioactive aerosols on the size of the added DOP aerosols, the energy of the neutrons and the kinds of nuclides were studied. The observed size distributions of the radioactive particles were explained by attachment of the radioactive atoms generated by the neutron-induced reactions to the DOP aerosols. (author)

  4. Ultrafine particle transport and deposition in a large scale 17-generation lung model.

    Science.gov (United States)

    Islam, Mohammad S; Saha, Suvash C; Sauret, Emilie; Gemci, Tevfik; Yang, Ian A; Gu, Y T

    2017-11-07

    To understand how to assess optimally the risks of inhaled particles on respiratory health, it is necessary to comprehend the uptake of ultrafine particulate matter by inhalation during the complex transport process through a non-dichotomously bifurcating network of conduit airways. It is evident that the highly toxic ultrafine particles damage the respiratory epithelium in the terminal bronchioles. The wide range of in silico available and the limited realistic model for the extrathoracic region of the lung have improved understanding of the ultrafine particle transport and deposition (TD) in the upper airways. However, comprehensive ultrafine particle TD data for the real and entire lung model are still unavailable in the literature. Therefore, this study is aimed to provide an understanding of the ultrafine particle TD in the terminal bronchioles for the development of future therapeutics. The Euler-Lagrange (E-L) approach and ANSYS fluent (17.2) solver were used to investigate ultrafine particle TD. The physical conditions of sleeping, resting, and light activity were considered in this modelling study. A comprehensive pressure-drop along five selected path lines in different lobes was calculated. The non-linear behaviour of pressure-drops is observed, which could aid the health risk assessment system for patients with respiratory diseases. Numerical results also showed that ultrafine particle-deposition efficiency (DE) in different lobes is different for various physical activities. Moreover, the numerical results showed hot spots in various locations among the different lobes for different flow rates, which could be helpful for targeted therapeutical aerosol transport to terminal bronchioles and the alveolar region. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Investigation of flow behind vortex generators by stereo particle image velocimetry on a thick airfoil near stall

    DEFF Research Database (Denmark)

    Velte, Clara Marika; Hansen, Martin Otto Laver

    2013-01-01

    Stereoscopic Particle Image Velocimetry measurements investigating the effect of vortex generators (VGs) on the flow near stall were carried out in a purpose-built wind tunnel for airfoil investigations on a DU 91-W2-250 profile. Measurements were conducted at Re = 0.9⋅106, corresponding to free...... by a Snapshot Proper Orthogonal Decomposition analysis. This analysis also revealed some of the dynamics of the induced vortices. Copyright © 2012 John Wiley & Sons, Ltd....

  6. Membrane particles generated from mesenchymal stromal cells modulate immune responses by selective targeting of pro-inflammatory monocytes

    OpenAIRE

    Gonçalves, F.D.C. (Fabiany Da C.); Luk, Franka; Korevaar, Sander; Bouzid, R. (Rachid); Paz, A.H.; López-Iglesias, C. (Carmen); Baan, Carla; Merino, Ana; Hoogduijn, Martin

    2017-01-01

    textabstractMesenchymal stromal cells (MSC) are a promising therapy for immunological disorders. However, culture expanded MSC are large and get trapped in the capillary networks of the lungs after intravenous infusion, where they have a short survival time. Hypothetically, living cells are a risk for tumor formation. To reduce risks associated with MSC infusion and improve the distribution in the body, we generated membrane particles (MP) of MSC and MSC stimulated with IFN-γ (MPγ). Tracking ...

  7. Magnetic and Optical Properties of Submicron-Size Hollow Spheres

    Directory of Open Access Journals (Sweden)

    Hirofumi Yoshikawa

    2010-02-01

    Full Text Available Magnetic hollow spheres with a controlled diameter and shell thickness have emerged as an important class of magnetic nanomaterials. The confined hollow geometry and pronouncedly curved surfaces induce unique physical properties different from those of flat thin films and solid counterparts. In this paper, we focus on recent progress on submicron-size spherical hollow magnets (e.g., cobalt- and iron-based materials, and discuss the effects of the hollow shape and the submicron size on magnetic and optical properties.

  8. An introduction to deep submicron CMOS for vertex applications

    CERN Document Server

    Campbell, M; Cantatore, E; Faccio, F; Heijne, Erik H M; Jarron, P; Santiard, Jean-Claude; Snoeys, W; Wyllie, K

    2001-01-01

    Microelectronics has become a key enabling technology in the development of tracking detectors for High Energy Physics. Deep submicron CMOS is likely to be extensively used in all future tracking systems. Radiation tolerance in the Mrad region has been achieved and complete readout chips comprising many millions of transistors now exist. The choice of technology is dictated by market forces but the adoption of deep submicron CMOS for tracking applications still poses some challenges. The techniques used are reviewed and some of the future challenges are discussed.

  9. A method for generating uniform size-segregated pyrite particle fractions

    Directory of Open Access Journals (Sweden)

    Capo Rosemary C

    2007-10-01

    Full Text Available Abstract Background Standardized sample preparation techniques allow comparison of pyrite dissolution experiments under diverse conditions. Our objective was to assess dry and wet sieving preparation methodologies, and to develop a reproducible technique that yields uniformly size-distributed material within a limited size range of interest. Results Here, we describe a wet sieving preparation method that successfully concentrates pyrite particles within a 44–75 μm diameter range. In addition, this technique does not require a post-processing cleanup step to remove adhering particles, as those particles are removed during the procedure. We show that sample preparation methods not only affect the pyrite size distribution, but also apparent dissolution rates. Conclusion The presented methodology is non-destructive to the sample, uses readily available chemical equipment within the laboratory, and could be applied to minerals other than pyrite.

  10. Development of an expert system for automatic mesh generation for S(N) particle transport method in parallel environment

    Science.gov (United States)

    Patchimpattapong, Apisit

    This dissertation develops an expert system for generating an effective spatial mesh distribution for the discrete ordinates particle transport method in a parallel environment. This expert system consists of two main parts: (1) an algorithm for generating an effective mesh distribution in a serial environment, and (2) an algorithm for inference of an effective domain decomposition strategy for parallel computing. The mesh generation algorithm consists of four steps: creation of a geometric model as partitioned into coarse meshes, determination of an approximate flux shape, selection of appropriate differencing schemes, and generation of an effective fine mesh distribution. A geometric model was created using AutoCAD. A parallel code PENFC (Parallel Environment Neutral-Particle First Collision) has been developed to calculate an uncollided flux in a 3-D Cartesian geometry. The appropriate differencing schemes were selected based on the uncollided flux distribution using a least squares methodology. A menu-driven serial code PENXMSH has been developed to generate an effective spatial mesh distribution that preserves problem geometry and physics. The domain decomposition selection process involves evaluation of the four factors that affect parallel performance, which include number of processors and memory available per processor, load balance, granularity, and degree-of-coupling among processors. These factors are used to derive a parallel-performance-index that provides expected performance of a parallel algorithm depending on computing environment and resources. A large index indicates a high granularity algorithm with relatively low coupling among processors. This expert system has been successfully tested within the PENTRAN (Parallel Environment Neutral-Particle Transport) code system for simulating real-life shielding problems: the VENUS-3 experimental facility and the BWR core shroud.

  11. Immersion freezing induced by different kinds of coal fly ash: Comparing particle generation methods and measurement techniques

    Science.gov (United States)

    Grawe, Sarah; Augustin-Bauditz, Stefanie; Clemen, Hans-Christian; Eriksen-Hammer, Stine; Lubitz, Jasmin; Schneider, Johannes; Stratmann, Frank; Wex, Heike

    2017-04-01

    To date, a lot of effort has been put into the identification and characterization of atmospheric ice nucleating particles (INPs), which may influence both weather and climate. The majority of studies focuses on INPs from natural origin such as biological particles or mineral dust particles (Hoose and Möhler 2012, Murray et al. 2012). Combustion ashes, being possible sources of anthropogenic INPs, have rarely been investigated in the past. Ash particles may be emitted into the atmosphere either by the action of wind from ash deposits on the ground (bottom ash), or during the combustion process (fly ash). Two recent studies (Umo et al., 2015; Grawe et al., 2016) identified fly ash from coal combustion as the most efficient of the investigated samples (including also bottom ashes from wood and coal combustion). These results motivate the here presented study in which we investigated the immersion freezing behavior of four coal fly ash samples taken from the filters of different coal-fired power plants in Germany. A combination of two instruments was used to capture the temperature range from 0 °C to the homogeneous freezing limit at around -38 °C. Firstly, the new Leipzig Ice Nucleation Array (LINA) was used, where droplets from an ash-water suspension are pipetted onto a cooled plate. Secondly, we used the Leipzig Aerosol Cloud Interaction Simulator (LACIS; Hartmann et al., 2011), a laminar flow tube in which every droplet contains a single size-segregated ash particle. Here, it was possible to study the effect of different kinds of particle generation, i.e., atomization of an ash-water suspension, and aerosolization of dry ash material. The composition of the ash particles was investigated by means of single particle aerosol mass spectrometry and particles were sampled on filters for environmental scanning electron microscope analysis. Our measurements show that all four fly ash samples feature a similar immersion freezing behavior (ice fractions vary by a

  12. Bloch-Wave Engineered Submicron Diameter Micropillars with Quality Factors Exceeding 10,000

    DEFF Research Database (Denmark)

    Hofling, S.; Lermer, M.; Gregersen, Niels

    2011-01-01

    Adiabatic design submicron diameter quantum-dot micropillars have been designed and implemented for cavity quantum electrodynamics experiments. Ultra-high experimental quality factors (>10,000) are obtained for submicron diameters and strong light-matter interaction is observed.......Adiabatic design submicron diameter quantum-dot micropillars have been designed and implemented for cavity quantum electrodynamics experiments. Ultra-high experimental quality factors (>10,000) are obtained for submicron diameters and strong light-matter interaction is observed....

  13. Direct deposition of gas phase generated aerosol gold nanoparticles into biological fluids--corona formation and particle size shifts.

    Directory of Open Access Journals (Sweden)

    Christian R Svensson

    Full Text Available An ongoing discussion whether traditional toxicological methods are sufficient to evaluate the risks associated with nanoparticle inhalation has led to the emergence of Air-Liquid interface toxicology. As a step in this process, this study explores the evolution of particle characteristics as they move from the airborne state into physiological solution. Airborne gold nanoparticles (AuNP are generated using an evaporation-condensation technique. Spherical and agglomerate AuNPs are deposited into physiological solutions of increasing biological complexity. The AuNP size is characterized in air as mobility diameter and in liquid as hydrodynamic diameter. AuNP:Protein aggregation in physiological solutions is determined using dynamic light scattering, particle tracking analysis, and UV absorption spectroscopy. AuNPs deposited into homocysteine buffer form large gold-aggregates. Spherical AuNPs deposited in solutions of albumin were trapped at the Air-Liquid interface but was readily suspended in the solutions with a size close to that of the airborne particles, indicating that AuNP:Protein complex formation is promoted. Deposition into serum and lung fluid resulted in larger complexes, reflecting the formation of a more complex protein corona. UV absorption spectroscopy indicated no further aggregation of the AuNPs after deposition in solution. The corona of the deposited AuNPs shows differences compared to AuNPs generated in suspension. Deposition of AuNPs from the aerosol phase into biological fluids offers a method to study the protein corona formed, upon inhalation and deposition in the lungs in a more realistic way compared to particle liquid suspensions. This is important since the protein corona together with key particle properties (e.g. size, shape and surface reactivity to a large extent may determine the nanoparticle effects and possible translocation to other organs.

  14. Next-generation solid-state detectors for charged particle spectroscopy

    Science.gov (United States)

    Ogasawara, K.; Livi, S. A.; Allegrini, F.; Broiles, T. W.; Dayeh, M. A.; Desai, M. I.; Ebert, R. W.; Llera, K.; Vines, S. K.; McComas, D. J.

    2016-07-01

    The performance of silicon avalanche photodiodes (APDs) and single crystal chemical vapor deposit diamond detectors (DDs) is reviewed in comparison with conventional silicon-based solid-state detectors (SSDs) from the perspective of space plasma applications. Although the low-energy threshold and the energy resolution are equivalent to SSDs, DDs offer a high radiation tolerance and very low leakage currents due to a wider band gap than silicon. In addition, DDs can operate at higher temperatures, are insensitive to light (>226 nm), and are capable of timing analysis due to the higher intrinsic carrier mobility. APDs also offer several advantageous features. Specifically, APDs have a lower energy threshold (linear response due to a strong electric field causing signal amplifications within the detector. Therefore, APDs can be used to detect lower energy particles, covering a larger portion of the energy spectrum than conventional SSDs. Further, the strong internal electric field gives them a subnanosecond response time by the charge mobility saturation, allowing them to make precise timing measurements of ions. These novel detector techniques can be potentially applied to improve the measurements of suprathermal particles, whose energies lie between typical ranges of conventional sensors for low-energy plasmas and energetic particles. Although the origin and evolution of the suprathermal particles are the key to understanding the acceleration and heating processes in space plasma, they are not well understood due to the technical difficulties of making the measurement.

  15. Effect of particle properties of powders on the generation and transmission of Raman scattering.

    Science.gov (United States)

    Townshend, Nichola; Nordon, Alison; Littlejohn, David; Andrews, John; Dallin, Paul

    2012-06-05

    Transmission Raman measurements of a 1 mm thick sulfur-containing disk were made at different positions as it was moved through 4 mm of aspirin (150-212 μm) or microcrystalline cellulose (Avicel) of different size ranges (transmission Raman intensity of the sulfur interlayer at 218 cm(-1) was lower when the disk was placed at the top or bottom of the powder bed, compared to positions within the bed and the difference between the sulfur intensity at the outer and inner positions increased with Avicel particle size. Also, the positional intensity difference was smaller for needle-shaped aspirin than for granular Avicel of the same size. The attenuation coefficients for the propagation of the exciting laser and transmitted Raman photons through the individual powders were the same but decreased as the particle size of Avicel increased; also, the attenuation coefficients for propagation through 150-212 μm aspirin were almost half of those through similar sized Avicel particles. The study has demonstrated that particulate size and type affect transmitted Raman intensities and, consequently, such factors need to be considered in the analysis of powders, especially if particle properties vary between the samples.

  16. Reactive oxygen species generated in the presence of fine pyrite particles and its implication in thermophilic mineral bioleaching.

    Science.gov (United States)

    Jones, G C; van Hille, R P; Harrison, S T L

    2013-03-01

    In the tank bioleaching process, maximising solid loading and mineral availability, the latter through decreasing particle size, are key to maximising metal extraction. In this study, the effect of particle size distribution on bioleaching performance and microbial growth was studied through applying knowledge based on medical geology research to understand the adverse effects of suspended fine pyrite particles. Small-scale leaching studies, using pyrite concentrate fractions (106-75, 75-25, -25 μm fines), were used to confirm decreasing performance with decreasing particle size (D 50 <40 μm). Under equivalent experimental conditions, the generation of the reactive oxygen species (ROS), hydrogen peroxide and hydroxyl radicals from pyrite was illustrated. ROS generation measured from the different pyrite fractions was found to increase with increasing pyrite surface area loading (1.79-74.01 m(2) L(-1)) and Fe(2+) concentration (0.1-2.8 g L(-1)) in solution. The highest concentration of ROS was measured from the finest fraction of pyrite (0.85 mM) and from the largest concentration of Fe(2+) (0.78 mM). No ROS was detected from solutions containing only Fe(3+) under the same conditions tested. The potential of ROS to inhibit microbial performance under bioleaching conditions was demonstrated. Pyrite-free Sulfolobus metallicus cultures challenged with hydrogen peroxide (0.5-2.5 mM) showed significant decrease in both cell growth and Fe(2+) oxidation rates within the concentration range 1.5-2.5 mM. In combination, the results from this study suggest that conditions of large pyrite surface area loading, coupled with high concentrations of dissolved Fe(2+), can lead to the generation of ROS, resulting in oxidative stress of the microorganisms.

  17. Submicron/nano-structured icephobic surfaces made from fluorinated polymethylsiloxane and octavinyl-POSS

    Energy Technology Data Exchange (ETDEWEB)

    Li, Yancai; Luo, Chenghao; Li, Xiaohui; Zhang, Kaiqiang; Zhao, Yunhui; Zhu, Kongying; Yuan, Xiaoyan, E-mail: yuanxy@tju.edu.cn

    2016-01-01

    Graphical abstract: The submicron/nano-structured morphology induced by OVPOSS has a strong effect on ice attachment. The OVPOSS particles aggregated on the top surface could decrease the ice adhesion strength. - Highlights: • Fluorinated hybrid films were fabricated from PMHS–xFMA and OVPOSS. • The hybrid films presented icephobic surfaces in submicron/nano-structure. • PMHS–17FMA could enhance hydrophobicity rather than icephobic properties. • Proper OVPOSS content (10–15 wt%) favored reducing the ice adhesion strength. • Rougher surface morphology (R{sub q} > 90 nm) was benefit for repelling water droplets. - Abstract: Fluorinated hybrid films composed of fluorinated polymethylsiloxane (PMHS–xFMA, x = 6, 13, 17) and octavinyl-polyhedral oligomeric silsesquioxanes (OVPOSS) were prepared for icephobic applications. PMHS–xFMA with diverse fluorinated side groups were synthesized via hydrosilylation of polymethylhydrosiloxane (PMHS) with fluorinated methacrylate (xFMA), i.e., hexafluorobutyl methacrylate (6FMA), tridecafluorooctyl methacrylate (13FMA) and heptadecafluorodecyl methacrylate (17FMA), respectively. Characterizations of atomic force microscope and scanning electron microscope indicated that surfaces of the hybrid films consisted of submicron/nano-scaled OVPOSS aggregates, and the root-mean-square roughness (S{sub q}) could vary from 42.6 nm to 145.2 nm with various OVPOSS content (5–20 wt%). Wettability measurements of the prepared films demonstrated that the relatively longer fluorinated side groups in PMHS–17FMA were beneficial for decreasing surface energy and enhancing hydrophobic properties. However, the fluorinated hybrid films with PMHS–17FMA presented higher ice shear strengths due to the stronger interfacial interactions between the film surface and ice/water. The film prepared by PMHS–13FMA and 10 wt% of OVPOSS with proper roughness (90.2 nm) performed the lowest ice shear strength (188.2 ± 13.4 kPa) among all the

  18. Deep-submicron CMOS Single Photon Detectors and Quantum Effects

    NARCIS (Netherlands)

    Karami, M.A.

    2011-01-01

    Quantum parasitic effects and miniaturization of Single Photon Avalanche Diodes in deep-submicron technologies have been studied in this thesis in detail. Tunneling noise and Random Telegraph Signal (RTS) noise have been the main two parasitic effects addressed comprehensively. While the fundamental

  19. The Virtual Resistance Control Strategy for HVRT of Doubly Fed Induction Wind Generators Based on Particle Swarm Optimization

    Directory of Open Access Journals (Sweden)

    Zhen Xie

    2014-01-01

    Full Text Available Grid voltage swell will cause transient DC flux component in the doubly fed induction generator (DFIG stator windings, creating serious stator and rotor current and torque oscillation, which is more serious than influence of the voltage dip. It is found that virtual resistance manages effectively to suppress rotor current and torque oscillation, avoid the operation of crowbar circuit, and enhance its high voltage ride through technology capability. In order to acquire the best virtual resistance value, the excellent particle library (EPL of dynamic particle swarm optimization (PSO algorithm is proposed. It takes the rotor voltage and rotor current as two objectives, which has a fast convergence performance and high accuracy. Simulation and experimental results verify the effectiveness of the virtual resistance control strategy.

  20. Co-formation of hydroperoxides and ultra-fine particles during the reactions of ozone with a complex VOC mixture under simulated indoor conditions

    DEFF Research Database (Denmark)

    Fan, Z.H.; Weschler, Charles J.; Han, IK

    2005-01-01

    In this study we examined the co-formation of hydrogen peroxide and other hydroperoxides (collectively presented as H2O2*) as well as submicron particles, including ultra-fine particles (UFP), resulting from the reactions of ozone (O-3) with a complex mixture of volatile organic compounds (VOCs...... in the O-3/23 VOCs system. The present study confirmed the findings of a previous study carried out in a real-world office and generated new findings regarding co-formation of UFP. Through a comparative analysis of H2O2* yields under different reaction conditions, this study demonstrates that VOCs co...

  1. Contrasting organic aerosol particles from boreal and tropical forests during HUMPPA-COPEC-2010 and AMAZE-08 using coherent vibrational spectroscopy

    Directory of Open Access Journals (Sweden)

    C. J. Ebben

    2011-10-01

    Full Text Available We present the vibrational sum frequency generation spectra of organic particles collected in a boreal forest in Finland and a tropical forest in Brazil. These spectra are compared to those of secondary organic material produced in the Harvard Environmental Chamber. By comparing coherent vibrational spectra of a variety of terpene and olefin reference compounds, along with the secondary organic material synthesized in the environmental chamber, we show that submicron aerosol particles sampled in Southern Finland during HUMPPA-COPEC-2010 are composed to a large degree of material similar in chemical composition to synthetic α-pinene-derived material. For material collected in Brazil as part of AMAZE-08, the organic component is found to be chemically complex in the coarse mode but highly uniform in the fine mode. When combined with histogram analyses of the isoprene and monoterpene abundance recorded during the HUMPPA-COPEC-2010 and AMAZE-08 campaigns, the findings presented here indicate that if air is rich in monoterpenes, submicron-sized secondary aerosol particles that form under normal OH and O3 concentration levels can be described in terms of their hydrocarbon content as being similar to α-pinene-derived model secondary organic aerosol particles. If the isoprene concentration dominates the chemical composition of organic compounds in forest air, then the hydrocarbon component of secondary organic material in the submicron size range is not simply well-represented by that of isoprene-derived model secondary organic aerosol particles but is more complex. Throughout the climate-relevant size range of the fine mode, however, we find that the chemical composition of the secondary organic particle material from such air is invariant with size, suggesting that the particle growth does not change the chemical composition of the hydrocarbon component of the particles in a significant way.

  2. Fluxes of Submicron Organic Aerosol above London Measured by Eddy Covariance using the Aerodyne HR-ToF-AMS

    Science.gov (United States)

    Phillips, G. J.; di Marco, C. F.; Farmer, D.; Kimmel, J. R.; Jimenez, J. L.; Nemitz, E.

    2009-12-01

    Urban centres are large sources of sub-micron particles. The myriad of emission sources combined with the complex interaction between regional aerosol and the particulate and gaseous photochemistry make for a complex system. It is evident that particulate emissions from cities will affect the regional atmosphere as well as the environment within the urban area. Aerosol particles have been associated with respiratory and cardio-vascular disease and are also linked with the climate through scattering of radiation and indirect effects such as cloud formation. The Aerodyne Aerosol Mass Spectrometer (AMS) provides a powerful tool to elucidate the sources and processing of organic aerosol in the urban atmosphere. Normally this is done through concentration measurements, by statistical analysis of the organic mass spectra, e.g. using Positive Matrix Factorization (PMF). Recently the quadrupole based AMS (Q-AMS) has been used for the micrometeorological measurement of organic aerosol fluxes above several cities, based on high frequency measurements of individual masses (m/z) representative of different organic mass fractions. While providing a major step forward towards quantification of urban organic aerosol emissions and processing, the interpretation of Q-AMS flux data requires assumptions to scale up signals on individual m/z to total organic mass fluxes. In this paper we present chemically-speciated and size-segregated number aerosol fluxes measured using the next generation eddy covariance flux system based on the Aerodyne HR-ToF-AMS, now capable of recording fast-response eddy-covariance time-series of all m/z simultaneously. This allows organic mass fluxes to be calculated more quantitatively and provides 'flux mass spectra' in addition to concentration mass spectra, which produces novel information on the local emission and processing of organic aerosols in the urban environment, while concentration analysis includes the regional background. The measurements were

  3. Fate of Multimeric Oligomers, Submicron, and Micron Size Aggregates of Monoclonal Antibodies Upon Subcutaneous Injection in Mice.

    Science.gov (United States)

    Kijanka, Grzegorz; Bee, Jared S; Bishop, Steven M; Que, Ivo; Löwik, Clemens; Jiskoot, Wim

    2016-05-01

    The aim of this study was to examine the fate of differently sized protein aggregates upon subcutaneous injection in mice. A murine and a human monoclonal immunoglobulin G 1 (IgG1) antibody were labeled with a fluorescent dye and subjected to stress conditions to create aggregates. Aggregates fractionated by centrifugation or gel permeation chromatography were administered subcutaneously into SKH1 mice. The biodistribution was measured by in vivo fluorescence imaging for up to 1 week post injection. At several time points, mice were sacrificed and selected organs and tissues were collected for ex vivo analysis. Part of injected aggregated IgGs persisted much longer at the injection site than unstressed controls. Aggregate fractions containing submicron (0.1-1 μm) or micron (1-100 μm) particles were retained to a similar extent. Highly fluorescent "hot-spots" were detected 24 h post injection in spleens of mice injected with submicron aggregates of murine IgG. Submicron aggregates of human IgG showed higher accumulation in draining lymph nodes 1 h post injection than unstressed controls or micron size aggregates. For both tested proteins, aggregated fractions seemed to be eliminated from circulation more rapidly than monomeric fractions. The biodistribution of monomers isolated from solutions subjected to stress conditions was similar to that of unstressed control. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  4. High Proportions of Sub-micron Particulate Matter in Icelandic Dust Storms in 2015

    Science.gov (United States)

    Dagsson Waldhauserova, Pavla; Arnalds, Olafur; Olafsson, Haraldur; Magnusdottir, Agnes

    2017-04-01

    Iceland is extremely active dust region and desert areas of over 44,000 km2 acknowledge Iceland as the largest Arctic and European desert. Frequent dust events, up to 135 dust days annually, transport dust particles far distances towards the Arctic and Europe. Satellite MODIS pictures have revealed dust plumes exceeding 1,000 km. The annual dust deposition was calculated as 40.1 million tons yr-1. Two dust storms were measured in transverse horizontal profile about 90 km far from different dust sources in southwestern Iceland in the summer of 2015. Aerosol monitor DustTrak DRX 8533EP was used to measure PM mass concentrations corresponding to PM1, PM2.5, PM4, PM10 and the total PM15 at several places within the dust plume. Images from camera network operated by the Icelandic Road and Coastal Administration were used to estimate the visibility and spatial extent of measured dust events. A numerical simulation of surface winds was carried out with the numerical model HIRLAM with horizontal resolution of 5 km and used to calculate the total dust flux from the sources. The in situ measurements inside the dust plumes showed that aeolian dust can be very fine. The study highlights that suspended volcanic dust in Iceland causes air pollution with extremely high PM1 concentrations comparable to the polluted urban stations in Europe or Asia rather than reported dust event observations from around the world. The PM1/PM2.5 ratios are generally low during dust storms outside of Iceland, much lower than > 0.9 and PM1/PM10 ratios of 0.34-0.63 found in our study. It shows that Icelandic volcanic dust consists of higher proportion of submicron particles compared to crustal dust. The submicron particles are predicted to travel long distances. Moreover, such submicron particles pose considerable health risk because of high potential for entering the lungs. Icelandic volcanic glass has often fine pipe-vesicular structures known from asbestos and high content of heavy metals. Previous

  5. Perspectives on Entangled Nuclear Particle Pairs Generation and Manipulation in Quantum Communication and Cryptography Systems

    Directory of Open Access Journals (Sweden)

    Octavian Dănilă

    2012-01-01

    Full Text Available Entanglement between two quantum elements is a phenomenon which presents a broad application spectrum, being used largely in quantum cryptography schemes and in physical characterisation of the universe. Commonly known entangled states have been obtained with photons and electrons, but other quantum elements such as quarks, leptons, and neutrinos have shown their informational potential. In this paper, we present the perspective of exploiting the phenomenon of entanglement that appears in nuclear particle interactions as a resource for quantum key distribution protocols.

  6. The United States Particle Accelerator School: Educating the next generation of accelerator scientists and engineers

    Energy Technology Data Exchange (ETDEWEB)

    Barletta, William A.; /MIT

    2008-09-01

    Only a handful of universities in the US offer any formal training in accelerator science. The United States Particle Accelerator School (USPAS) is National Graduate Educational Program that has developed a highly successful educational paradigm that, over the past twenty-years, has granted more university credit in accelerator / beam science and technology than any university in the world. Sessions are held twice annually, hosted by major US research universities that approve course credit, certify the USPAS faculty, and grant course credit. The USPAS paradigm is readily extensible to other rapidly developing, crossdisciplinary research areas such as high energy density physics.

  7. Neutrinos from binary pulsars. [generated by high energy particles striking companion star

    Science.gov (United States)

    Eichler, D.

    1978-01-01

    It is shown that binary systems containing moderately young pulsars may emit high-energy neutrinos (between 1 and 100 TeV) at detectable levels. The pulsars are assumed to have total luminosities of the order of 10 to the 38th erg/sec. The neutrinos are produced by high energy particles (e.g. protons) from the pulsar striking the companion. Cyg X3 may be detectable in high-energy neutrinos if it emits greater than about 10 to the 35th erg/sec in high-energy protons. There may be a whole class of objects like Cyg X3, but obscured by thick accretion clouds.

  8. Quantification of Vortex Generation Due to Non-Equilibrium Electrokinetics at the Micro/Nanochannel Interface: Particle Tracking Velocimetry

    Directory of Open Access Journals (Sweden)

    Seung Jun Lee

    2016-07-01

    Full Text Available We describe a quantitative study of vortex generation due to non-equilibrium electrokinetics near a micro/nanochannel interface. The microfluidic device is comprised of a microchannel with a set of nanochannels. These perm-selective nanochannels induce flow instability and thereby produce strong vortex generation. We performed tracking visualization of fluorescent microparticles to obtain velocity fields. Particle tracking enables the calculation of an averaged velocity field and the velocity fluctuations. We characterized the effect of applied voltages and electrolyte concentrations on vortex formation. The experimental results show that an increasing voltage or decreasing concentration results in a larger vortex region and a strong velocity fluctuation. We calculate the normalized velocity fluctuation—whose meaning is comparable to turbulent intensity—and we found that it is as high as 0.12. This value is indicative of very efficient mixing, albeit with a small Reynolds number.

  9. Self-generated clouds of micron-sized particles as a promising way of a Solar Probe shielding from intense thermal radiation of the Sun

    Science.gov (United States)

    Dombrovsky, Leonid A.; Reviznikov, Dmitry L.; Kryukov, Alexei P.; Levashov, Vladimir Yu

    2017-10-01

    An effect of shielding of an intense solar radiation towards a solar probe with the use of micron-sized SiC particles generated during ablation of a composite thermal protection material is estimated on a basis of numerical solution to a combined radiative and heat transfer problem. The radiative properties of particles are calculated using the Mie theory, and the spectral two-flux model is employed in radiative transfer calculations for non-uniform particle clouds. A computational model for generation and evolution of the cloud is based on a conjugated heat transfer problem taking into account heating and thermal destruction of the matrix of thermal protection material and sublimation of SiC particles in the generated cloud. The effect of light pressure, which is especially important for small particles, is also taken into account. The computational data for mass loss due to the particle cloud sublimation showed the low value about 1 kg/m2 per hour at the distance between the vehicle and the Sun surface of about four radii of the Sun. This indicates that embedding of silicon carbide or other particles into a thermal protection layer and the resulting generation of a particle cloud can be considered as a promising way to improve the possibilities of space missions due to a significant decrease in the vehicle working distance from the solar photosphere.

  10. CaloGAN: Simulating 3D high energy particle showers in multilayer electromagnetic calorimeters with generative adversarial networks

    Science.gov (United States)

    Paganini, Michela; de Oliveira, Luke; Nachman, Benjamin

    2018-01-01

    The precise modeling of subatomic particle interactions and propagation through matter is paramount for the advancement of nuclear and particle physics searches and precision measurements. The most computationally expensive step in the simulation pipeline of a typical experiment at the Large Hadron Collider (LHC) is the detailed modeling of the full complexity of physics processes that govern the motion and evolution of particle showers inside calorimeters. We introduce CaloGAN, a new fast simulation technique based on generative adversarial networks (GANs). We apply these neural networks to the modeling of electromagnetic showers in a longitudinally segmented calorimeter and achieve speedup factors comparable to or better than existing full simulation techniques on CPU (100 ×-1000 × ) and even faster on GPU (up to ˜105× ). There are still challenges for achieving precision across the entire phase space, but our solution can reproduce a variety of geometric shower shape properties of photons, positrons, and charged pions. This represents a significant stepping stone toward a full neural network-based detector simulation that could save significant computing time and enable many analyses now and in the future.

  11. Properties and toxicological effects of particles from the interaction between tyres, road pavement and winter traction material.

    Science.gov (United States)

    Gustafsson, Mats; Blomqvist, Göran; Gudmundsson, Anders; Dahl, Andreas; Swietlicki, Erik; Bohgard, Mats; Lindbom, John; Ljungman, Anders

    2008-04-15

    In regions where studded tyres and traction material are used during winter, e.g. the Nordic countries, northern part of USA, Canada, and Japan, mechanically generated particles from traffic are the main reason for high particle mass concentrations in busy street and road environments. In many Nordic municipalities the European environmental quality standard for inhalable particles (PM(10)) is exceeded due to these particles. In this study, particles from the wear of studded and studless friction tyres on two pavements and traction sanding were generated using a road simulator. The particles were characterized using particle sizers, Particle Induced X-Ray Emission Analysis and electron microscopy. Cell studies were conducted on particles sampled from the tests with studded tyres and compared with street environment, diesel exhaust and subway PM(10), respectively. The results show that in the road simulator, where resuspension is minimized, studded tyres produce tens of times more particles than friction tyres. Chemical analysis of the sampled particles shows that the generated wear particles consist almost entirely of minerals from the pavement stone material, but also that Sulfur is enriched for the submicron particles and that Zink is enriched for friction tyres for all particles sizes. The chemical data can be used for source identification and apportionment in urban aerosol studies. A mode of ultra-fine particles was also present and is hypothesised to originate in the tyres. Further, traction material properties affect PM(10) emission. The inflammatory potential of the particles from wear of pavements seems to depend on type of pavement and can be at least as potent as diesel exhaust particles. The results imply that there is a need and a good potential to reduce particle emission from pavement wear and winter time road and street operation by adjusting both studded tyre use as well as pavement and traction material properties.

  12. Properties and toxicological effects of particles from the interaction between tyres, road pavement and winter traction material

    Energy Technology Data Exchange (ETDEWEB)

    Gustafsson, Mats [Swedish National Road and Transport Research Institute (VTI), SE-581 95 Linkoeping (Sweden)], E-mail: mats.gustafsson@vti.se; Blomqvist, Goeran [Swedish National Road and Transport Research Institute (VTI), SE-581 95 Linkoeping (Sweden); Gudmundsson, Anders; Dahl, Andreas [Division of Ergonomics and Aerosol Technology, Department of Design Sciences, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Swietlicki, Erik [Division of Nuclear Physics, Department of Physics, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Bohgard, Mats [Division of Ergonomics and Aerosol Technology, Department of Design Sciences, Lund University, P.O. Box 118, SE-221 00 Lund (Sweden); Lindbom, John; Ljungman, Anders [Faculty of Health Sciences, Department of Molecular and Clinical Medicine, Division of Occupational and Environmental Medicine, SE-581 85 Linkoeping (Sweden)

    2008-04-15

    In regions where studded tyres and traction material are used during winter, e.g. the Nordic countries, northern part of USA, Canada, and Japan, mechanically generated particles from traffic are the main reason for high particle mass concentrations in busy street and road environments. In many Nordic municipalities the European environmental quality standard for inhalable particles (PM{sub 10}) is exceeded due to these particles. In this study, particles from the wear of studded and studless friction tyres on two pavements and traction sanding were generated using a road simulator. The particles were characterized using particle sizers, Particle Induced X-Ray Emission Analysis and electron microscopy. Cell studies were conducted on particles sampled from the tests with studded tyres and compared with street environment, diesel exhaust and subway PM{sub 10}, respectively. The results show that in the road simulator, where resuspension is minimized, studded tyres produce tens of times more particles than friction tyres. Chemical analysis of the sampled particles shows that the generated wear particles consist almost entirely of minerals from the pavement stone material, but also that Sulfur is enriched for the submicron particles and that Zink is enriched for friction tyres for all particles sizes. The chemical data can be used for source identification and apportionment in urban aerosol studies. A mode of ultra-fine particles was also present and is hypothesised to originate in the tyres. Further, traction material properties affect PM{sub 10} emission. The inflammatory potential of the particles from wear of pavements seems to depend on type of pavement and can be at least as potent as diesel exhaust particles. The results imply that there is a need and a good potential to reduce particle emission from pavement wear and winter time road and street operation by adjusting both studded tyre use as well as pavement and traction material properties.

  13. Flange joint system for SRF cavities utilizing high force spring clamps for low particle generation

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-09-05

    A flange joint system for SRF cavities. The flange joint system includes a set of high force spring clamps that produce high force on the simple flanges of Superconducting Radio Frequency (SRF) cavities to squeeze conventional metallic seals. The system establishes the required vacuum and RF-tight seal with minimum particle contamination to the inside of the cavity assembly. The spring clamps are designed to stay within their elastic range while being forced open enough to mount over the flange pair. Upon release, the clamps have enough force to plastically deform metallic seal surfaces and continue to a new equilibrium sprung dimension where the flanges remain held against one another with enough preload such that normal handling will not break the seal.

  14. Laser or charged-particle-beam fusion reactor with direct electric generation by magnetic flux compression

    Science.gov (United States)

    Lasche, George P.

    1988-01-01

    A high-power-density laser or charged-particle-beam fusion reactor system maximizes the directed kinetic energy imparted to a large mass of liquid lithium by a centrally located fusion target. A fusion target is embedded in a large mass of lithium, of sufficient radius to act as a tritium breeding blanket, and provided with ports for the access of beam energy to implode the target. The directed kinetic energy is converted directly to electricity with high efficiency by work done against a pulsed magnetic field applied exterior to the lithium. Because the system maximizes the blanket thickness per unit volume of lithium, neutron-induced radioactivities in the reaction chamber wall are several orders of magnitude less than is typical of other fusion reactor systems.

  15. Preparation of superhard cubic boron nitride sintered from commercially available submicron powders

    Science.gov (United States)

    Liu, Teng; Kou, Zili; Lu, Jingrui; Yan, Xiaozhi; Liu, Fangming; Li, Xin; Ding, Wei; Liu, Jin; Zhang, Qiang; Wang, Qiang; Ma, Dejiang; Lei, Li; He, Duanwei

    2017-03-01

    Using submicron cubic boron nitride (cBN) powder as a starting material, polycrystalline cBN (PcBN) samples without additives were sintered from 8.0-14.0 GPa at 1750 °C, and their sintering behaviour and mechanical properties were investigated. Transmission electron microscopy analysis showed that high-density nanotwins could be generated from common submicron cBN grains during high pressure and high temperature treatment. The dislocation glide and (111) mechanical micro-twinning are the main mechanisms that underlie plastic deformation in the sintering process, and this contributes to the grain refinement. A refinement in the grain size (˜120 nm), micro-defect (nanotwin and stacking faults), and strong covalent bonding between the grains are crucial for improving the sample mechanical properties. The PcBN sintered at 11.0 GPa/1750 °C possessed outstanding mechanical properties, including a high Vickers hardness (˜72 GPa), fracture toughness (˜12.4 MPam1/2), and thermal stability (˜1273 °C in air).

  16. APSTNG: Associated particle sealed-tube neutron generator studies for arms control. Final report on NN-20 Project ST220

    Energy Technology Data Exchange (ETDEWEB)

    Rhodes, E.; Dickerman, C.E.; Brunner, T.; Hess, A.; Tylinski, S.

    1994-12-01

    Argonne National Laboratory has performed research and development on the use of Associated Particle Sealed-Tube Neutron Generator (APSTNG) technology for treaty verification and non-proliferation applications, under funding from the DOE Office of Nonproliferation and National Security. Results indicate that this technology has significant potential for nondestructively detecting elemental compositions inside inspected objects or volumes. The final phase of this project was placement of an order for commercial procurement of an advanced sealed tube, with its high-voltage supply and control systems. Procurement specifications reflected lessons learned during the study. The APSTNG interrogates a volume with a continuous 14-MeV neutron flux. Each neutron is emitted coincident with an {open_quotes}associated{close_quotes} alpha-particle emitted in the opposite direction. Thus detection of an alpha-particle marks the emission of a neutron in a cone opposite to that defined by the alpha detector. Detection of a gamma ray coincident with the alpha indicates that the gamma was emitted from a neutron-induced reaction inside the neutron cone: the gamma spectra can be used to identify fissionable materials and many isotopes having an atomic number larger than that of boron. The differences in gamma-ray and alpha-particle detection times yield a coarse measurement of the distance along the cone axis from the APSTNG emitter to each region containing the identified nuclide. A position-sensitive alpha detector would permit construction of coarse three-dimensional images. The source and emission-detection systems can be located on the same side of the interrogated volume. The neutrons and gamma rays are highly penetrating. A relatively high signal-to-background ratio allows the use of a relatively small neutron source and conventional electronics.

  17. Heat generation by eddy currents in a shell of superconducting bus-bars for SIS100 particle accelerator at FAIR

    Directory of Open Access Journals (Sweden)

    Tomków Łukasz

    2017-12-01

    Full Text Available Superconducting magnets in the SIS100 particle accelerator require the supply of liquid helium and electric current. Both are transported with by-pass lines designed at Wrocław University of Technology. Bus-bars used to transfer an electric current between the sections of the accelerator will be encased in a steel shell. Eddy currents are expected to appear in the shell during fast-ramp operation of magnets. Heat generation, which should be limited in any cryogenic system, will appear in the shell. In this work the amount of heat generated is assessed depending on the geometry of an assembly of the bus-bars and the shell. Numerical and analytical calculations are described. It was found that heat generation in the shell is relatively small when compared to other sources present in the accelerator and its value strongly depends on the geometry of the shell. The distribution of eddy currents and generated heat for different geometrical options are presented. Based on the results of the calculations the optimal design is proposed.

  18. Images reveal that atmospheric particles can undergo liquid-liquid phase separations

    Energy Technology Data Exchange (ETDEWEB)

    You, Yuan; Renbaum-Wolff, Lindsay; Carreras-Sospedra, Marc; Hanna, Sarah; Hiranuma, Naruki; Kamal, Saeid; Smith, Mackenzie L.; Zhang, Xiaolu; Weber, Rodney; Shilling, John E.; Dabdub, Donald; Martin, Scot T.; Bertram, Allan K.

    2012-07-30

    A large fraction of submicron atmospheric particles contains both organic material and inorganic salts. As the relative humidity cycles in the atmosphere, these mixed particles can undergo a range of phase transitions, possibly including liquid-liquid phase separation. If liquid-liquid phase separation occurs, the gas-particle partitioning of atmospheric semi-volatile organic compounds, the scattering and absorption of solar radiation, and the uptake of reactive gas species on atmospheric particles will be affected, with important implications for climate predictions. The actual occurrence of these types of phase transitions within individual atmospheric particles has been considered uncertain, in large part because of the absence of observations for real-world samples. Here, using optical and fluorescence microscopy, we observe the coexistence of two non-crystalline phases in particles generated from real-world samples collected on multiple days in Atlanta, Georgia, and in particles generated in the laboratory using atmospheric conditions. These results reveal that atmospheric particles can undergo liquid-liquid phase separations. Using a box model, we show that liquid-liquid phase separation can result in increased concentrations of gas-phase NO3 and N2O5 in the Atlanta region, due to decreased particle uptake of N2O5.

  19. Influence of physical properties and chemical composition of sample on formation of aerosol particles generated by nanosecond laser ablation at 213 nm

    Energy Technology Data Exchange (ETDEWEB)

    Hola, Marketa, E-mail: mhola@sci.muni.c [Department of Chemistry, Faculty of Science, Masaryk University, Kotlarska 2, 611 37 Brno (Czech Republic); Konecna, Veronika [Department of Chemistry, Faculty of Science, Masaryk University, Kotlarska 2, 611 37 Brno (Czech Republic); Mikuska, Pavel [Institute of Analytical Chemistry, Academy of Sciences of the Czech Republic v.v.i., Veveri 97, 602 00 Brno (Czech Republic); Kaiser, Jozef [Institute of Physical Engineering, Faculty of Mechanical Engineering, Brno University of Technology, Technicka 2896/2, 616 69 Brno (Czech Republic); Kanicky, Viktor [Department of Chemistry, Faculty of Science, Masaryk University, Kotlarska 2, 611 37 Brno (Czech Republic)

    2010-01-15

    The influence of sample properties and composition on the size and concentration of aerosol particles generated by nanosecond Nd:YAG laser ablation at 213 nm was investigated for three sets of different materials, each containing five specimens with a similar matrix (Co-cemented carbides with a variable content of W and Co, steel samples with minor differences in elemental content and silica glasses with various colors). The concentration of ablated particles (particle number concentration, PNC) was measured in two size ranges (10-250 nm and 0.25-17 mum) using an optical aerosol spectrometer. The shapes and volumes of the ablation craters were obtained by Scanning Electron Microscopy (SEM) and by an optical profilometer, respectively. Additionally, the structure of the laser-generated particles was studied after their collection on a filter using SEM. The results of particle concentration measurements showed a significant dominance of particles smaller than 250 nm in comparison with larger particles, irrespective of the kind of material. Even if the number of particles larger than 0.25 mum is negligible (up to 0.1%), the volume of large particles that left the ablation cell can reach 50% of the whole particle volume depending on the material. Study of the ablation craters and the laser-generated particles showed a various number of particles produced by different ablation mechanisms (particle splashing or condensation), but the similar character of released particles for all materials was observed by SEM after particle collection on the membrane filter. The created aerosol always consisted of two main structures - spherical particles with diameters from tenths to units of micrometers originally ejected from the molten surface layer and mum-sized 'fibres' composed of primary agglomerates with diameters in the range between tens and hundreds of nanometers. The shape and structure of ablation craters were in good agreement with particle concentration

  20. Submicron bioactive glass tubes for bone tissue engineering.

    Science.gov (United States)

    Xie, Jingwei; Blough, Eric R; Wang, Chi-Hwa

    2012-02-01

    Herein we describe a method to fabricate submicron bioactive glass tubes using sol-gel and coaxial electrospinning techniques for applications in bone tissue engineering. Heavy mineral oil and gel solution were delivered by two independent syringe pumps during the coaxial electrospinning process. Subsequently, submicron bioactive glass tubes were obtained by removal of poly(vinyl pyrrolidone) and heavy mineral oil via calcination at 600 °C for 5 h. Tubular structure was confirmed by scanning electron microscopy and transmission electron microscopy imaging. We examined the bioactivity of submicron bioactive glass tubes and fibers and evaluated their biocompatibility, using electrospun poly(ε-caprolactone) fibers--a bioinactive material--for comparison. The bioactivity of the glass tubes was examined in a simulated body fluid and they demonstrated the formation of hydroxyapatite-like minerals on both the outer and inner surfaces. In contrast, mineralization only occurred on their surface for bioactive glass solid fibers. Energy-dispersive X-ray data suggested that the bioactive glass tubes had a faster induction of mineral formation than the solid fibers. We demonstrate that the proliferation rate of mouse preosteoblastic MC3T3-E1 cells on bioactive glass tubes was comparable to that on solid fibers. We also show that bioactive glass tubes can be loaded with a model protein drug, bovine serum albumin, and that these structures exhibit delayed release properties. The bioactivity of released lysozyme can be as high as 90.9%. Taken together, these data suggest that submicron bioactive glass tubes could hold great potential for use in bone tissue engineering as well as topical drug or gene delivery. Copyright © 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  1. Energy Efficient Signaling in Deep-submicron Technology

    Directory of Open Access Journals (Sweden)

    Imed Ben Dhaou

    2002-01-01

    Full Text Available In deep-submicron technology, global interconnect capacitances have started reaching several orders of magnitude greater than the intrinsic capacitances of the CMOS gates. The dynamic power consumption of a CMOS gate driving a global wire is the sum of the power dissipated due to (discharging (i the intrinsic capacitance of the gate, and (ii the wire capacitance. The latter is referred to as on-chip signaling power consumption.

  2. Submicron plasticity: yield stress, dislocation avalanches, and velocity distribution

    OpenAIRE

    Ispánovity, Péter Dusán; Groma, István; Györgyi, Géza; Csikor, Ferenc F.; Weygand, Daniel

    2010-01-01

    The existence of a well defined yield stress, where a macroscopic piece of crystal begins to plastically flow, has been one of the basic observations of materials science. In contrast to macroscopic samples, in micro- and nanocrystals the strain accumulates in distinct, unpredictable bursts, which makes controlled plastic forming rather difficult. Here we study by simulation, in two and three dimensions, plastic deformation of submicron objects under increasing stress. We show that, while the...

  3. Submicron Resolution Spectral-Domain Optical Coherence Tomography

    KAUST Repository

    Alarousu, Erkki

    2013-11-14

    Apparatuses and systems for submicron resolution spectral-domain optical coherence tomography (OCT) are disclosed. The system may use white light sources having wavelengths within 400-1000 nanometers, and achieve resolution below 1 .mu.m. The apparatus is aggregated into a unitary piece, and a user can connect the apparatus to a user provided controller and/or light source. The light source may be a supercontinuum source.

  4. Anthropogenic influences on the physical state of submicron particulate matter over a tropical forest

    Energy Technology Data Exchange (ETDEWEB)

    Bateman, Adam P.; Gong, Zhaoheng; Harder, Tristan H.; de Sá, Suzane S.; Wang, Bingbing; Castillo, Paulo; China, Swarup; Liu, Yingjun; O& amp; apos; Brien, Rachel E.; Palm, Brett B.; Shiu, Hung-Wei; Cirino, Glauber G.; Thalman, Ryan; Adachi, Kouji; Alexander, M. Lizabeth; Artaxo, Paulo; Bertram, Allan K.; Buseck, Peter R.; Gilles, Mary K.; Jimenez, Jose L.; Laskin, Alexander; Manzi, Antonio O.; Sedlacek, Arthur; Souza, Rodrigo A. F.; Wang, Jian; Zaveri, Rahul; Martin, Scot T.

    2017-02-06

    The occurrence of nonliquid and liquid physical states of submicron atmospheric particulate matter (PM) downwind of an urban region in central Amazonia was investigated. Measurements were conducted during two intensive operating periods (IOP1 and IOP2) that took place during the wet and dry seasons of the GoAmazon2014/5 campaign. Air masses representing variable influences of background conditions, urban pollution, and regional- and continental-scale biomass burning passed over the research site. As the air masses varied, particle rebound fraction, an indicator of physical state, was measured in real time at ground level using an impactor apparatus. Micrographs collected by transmission electron microscopy confirmed that liquid particles adhered, while nonliquid particles rebounded. Relative humidity (RH) was scanned to collect rebound curves. When the apparatus RH matched ambient RH, 95 % of the particles adhered as a campaign average. Secondary organic material, produced for the most part by the oxidation of volatile organic compounds emitted from the forest, produces liquid PM over this tropical forest. During periods of anthropogenic influence, by comparison, the rebound fraction dropped to as low as 60 % at 95 % RH. Analyses of the mass spectra of the atmospheric PM by positive-matrix factorization (PMF) and of concentrations of carbon monoxide, total particle number, and oxides of nitrogen were used to identify time periods affected by anthropogenic influences, including both urban pollution and biomass burning. The occurrence of nonliquid PM at high RH correlated with these indicators of anthropogenic influence. A linear model having as output the rebound fraction and as input the PMF factor loadings explained up to 70 % of the variance in the observed rebound fractions. Anthropogenic influences can contribute to the presence of nonliquid PM in the atmospheric particle population through the combined effects of molecular species that increase viscosity

  5. Scanning SQUID susceptometers with sub-micron spatial resolution

    Energy Technology Data Exchange (ETDEWEB)

    Kirtley, John R., E-mail: jkirtley@stanford.edu; Rosenberg, Aaron J.; Palmstrom, Johanna C.; Holland, Connor M.; Moler, Kathryn A. [Department of Applied Physics, Stanford University, Stanford, California 94305-4045 (United States); Paulius, Lisa [Department of Physics, Western Michigan University, Kalamazoo, Michigan 49008-5252 (United States); Spanton, Eric M. [Department of Physics, Stanford University, Stanford, California 94305-4045 (United States); Schiessl, Daniel [Attocube Systems AG, Königinstraße 11A, 80539 Munich (Germany); Jermain, Colin L.; Gibbons, Jonathan [Department of Physics, Cornell University, Cornell, Ithaca, New York 14853 (United States); Fung, Y.-K.K.; Gibson, Gerald W. [IBM Research Division, T. J. Watson Research Center, Yorktown Heights, New York 10598 (United States); Huber, Martin E. [Department of Physics, University of Colorado Denver, Denver, Colorado 80217-3364 (United States); Ralph, Daniel C. [Department of Physics, Cornell University, Cornell, Ithaca, New York 14853 (United States); Kavli Institute at Cornell, Ithaca, New York 14853 (United States); Ketchen, Mark B. [OcteVue, Hadley, Massachusetts 01035 (United States)

    2016-09-15

    Superconducting QUantum Interference Device (SQUID) microscopy has excellent magnetic field sensitivity, but suffers from modest spatial resolution when compared with other scanning probes. This spatial resolution is determined by both the size of the field sensitive area and the spacing between this area and the sample surface. In this paper we describe scanning SQUID susceptometers that achieve sub-micron spatial resolution while retaining a white noise floor flux sensitivity of ≈2μΦ{sub 0}/Hz{sup 1/2}. This high spatial resolution is accomplished by deep sub-micron feature sizes, well shielded pickup loops fabricated using a planarized process, and a deep etch step that minimizes the spacing between the sample surface and the SQUID pickup loop. We describe the design, modeling, fabrication, and testing of these sensors. Although sub-micron spatial resolution has been achieved previously in scanning SQUID sensors, our sensors not only achieve high spatial resolution but also have integrated modulation coils for flux feedback, integrated field coils for susceptibility measurements, and batch processing. They are therefore a generally applicable tool for imaging sample magnetization, currents, and susceptibilities with higher spatial resolution than previous susceptometers.

  6. Study of defect generated visible photoluminescence in zinc oxide nano-particles prepared using PVA templates

    Energy Technology Data Exchange (ETDEWEB)

    Oudhia, A. [Department of Physics, Government V.Y.T. PG. Autonomous College, Durg, 491001 C.G. (India); Choudhary, A., E-mail: aarti.bhilai@gmail.com [Department of Physics, Government V.Y.T. PG. Autonomous College, Durg, 491001 C.G. (India); Sharma, S.; Aggrawal, S. [Department of Physics, Government V.Y.T. PG. Autonomous College, Durg, 491001 C.G. (India); Dhoble, S.J. [RTM University Nagpur, Maharashtra (India)

    2014-10-15

    Intrinsic defect generated photoluminescence (PL) in zinc oxide nanoparticles (NPs) obtained by a PVA template based wet-chemical process has been studied. A good controllability was achieved on the surface defects, structure and the morphology of ZnO NPs through the variation of solvents used in synthesis. The PL emission strongly depended on the defect structure and morphology. SEM, XRD, annealing and PL excitation studies were used to analyze the types of defects involved in the visible emission as well as the defect concentration. The mechanism for the blue, green and yellow emissions was proposed. The spectral content of the visible emission was controlled through generation/removal of defects through the shape transformation or annealing by focusing on defect origins and broad controls. - Highlights: • ZnO nanoparticles were synthesized using poly-vinyl alcohol template in various solvents. • The structure and morphology of ZnO nanoparticles were depended on dielectric constant and boiling point of solvents. • Photoluminescence properties of ZnO nanoparticles were studied. • Maximum optical absorbance and Photoluminescence intensity were found in ethanolic preparation. • ZnO nanoparticles were annealed at different temperatures for detection of defect emission.

  7. Solar tower power plant using a particle-heated steam generator: Modeling and parametric study

    Science.gov (United States)

    Krüger, Michael; Bartsch, Philipp; Pointner, Harald; Zunft, Stefan

    2016-05-01

    Within the framework of the project HiTExStor II, a system model for the entire power plant consisting of volumetric air receiver, air-sand heat exchanger, sand storage system, steam generator and water-steam cycle was implemented in software "Ebsilon Professional". As a steam generator, the two technologies fluidized bed cooler and moving bed heat exchangers were considered. Physical models for the non-conventional power plant components as air- sand heat exchanger, fluidized bed coolers and moving bed heat exchanger had to be created and implemented in the simulation environment. Using the simulation model for the power plant, the individual components and subassemblies have been designed and the operating parameters were optimized in extensive parametric studies in terms of the essential degrees of freedom. The annual net electricity output for different systems was determined in annual performance calculations at a selected location (Huelva, Spain) using the optimized values for the studied parameters. The solution with moderate regenerative feed water heating has been found the most advantageous. Furthermore, the system with moving bed heat exchanger prevails over the system with fluidized bed cooler due to a 6 % higher net electricity yield.

  8. Replication-Deficient Particles: New Insights into the Next Generation of Bluetongue Virus Vaccines.

    Science.gov (United States)

    Celma, Cristina C; Stewart, Meredith; Wernike, Kerstin; Eschbaumer, Michael; Gonzalez-Molleda, Lorenzo; Breard, Emmanuel; Schulz, Claudia; Hoffmann, Bernd; Haegeman, Andy; De Clercq, Kris; Zientara, Stephan; van Rijn, Piet A; Beer, Martin; Roy, Polly

    2017-01-01

    Bluetongue virus (BTV) is endemic in many parts of the world, often causing severe hemorrhagic disease in livestock. To date, at least 27 different serotypes have been recognized. Vaccination against all serotypes is necessary to protect susceptible animals and to prevent onward spread of the virus by insect vectors. In our previous studies, we generated replication-deficient (disabled infectious single-cycle [DISC]) virus strains for a number of serotypes and reported preliminary data on their protective efficacy in animals. In this report, to advance the DISC vaccines to the marketplace, we investigated different parameters of these DISC vaccines. First, we demonstrated the genetic stabilities of these vaccine strains and also the complementing cell line. Subsequently, the optimal storage conditions of vaccines, including additives, temperature, and desiccation, were determined and their protective efficacies in animals confirmed. Furthermore, to test if mixtures of different vaccine strains could be tolerated, we tested cocktails of DISC vaccines in combinations of three or six different serotypes in sheep and cattle, the two natural hosts of BTV. Groups of sheep vaccinated with a cocktail of six different vaccines were completely protected from challenge with individual virulent serotypes, both in early challenge and after 5 months of challenge without any clinical disease. There was no interference in protection between the different vaccines. Protection was also achieved in cattle with a mixture of three vaccine strains, albeit at a lesser level than in sheep. Our data support and validate the suitability of these virus strains as the next-generation vaccines for BTV. Bluetongue (BT) is a debilitating and in many cases lethal disease that affects ruminants of economic importance. Classical vaccines that afford protection against bluetongue virus, the etiological agent, are not free from secondary and undesirable effects. A surge in new approaches to produce

  9. Review of single particle dynamics for third generation light sources through frequency map analysis

    Directory of Open Access Journals (Sweden)

    L. Nadolski

    2003-11-01

    Full Text Available Frequency map analysis [J. Laskar, Icarus 88, 266 (1990] is used here to analyze the transverse dynamics of four third generation synchrotron light sources: the ALS, the ESRF, the SOLEIL project, and Super-ACO. Time variations of the betatron tunes give additional information for the global dynamics of the beam. The main resonances are revealed; a one-to-one correspondence between the configuration space and the frequency space can be performed. We stress that the frequency maps, and therefore the dynamics optimization, are highly sensitive to sextupolar strengths and vary in a large amount from one machine to another. The frequency maps can thus be used to characterize the different machines.

  10. Measuring Mass-Based Hygroscopicity of Atmospheric Particles through in situ Imaging

    Energy Technology Data Exchange (ETDEWEB)

    Piens, Dominique` Y.; Kelly, Stephen T.; Harder, Tristan; Petters, Markus D.; O' Brien, Rachel; Wang, Bingbing; Teske, Ken; Dowell, Pat; Laskin, Alexander; Gilles, Mary K.

    2016-04-18

    Quantifying how atmospheric particles interact with water vapor is critical for understanding the effects of aerosols on climate. We present a novel method to measure the mass-based hygroscopicity of particles while characterizing their elemental and carbon functional group compositions. Since mass-based hygroscopicity is insensitive to particle geometry, it is advantageous for probing the hygroscopic behavior of atmospheric particles, which can have irregular morphologies. Combining scanning electron microscopy with energy dispersive X-ray analysis (SEM/EDX), scanning transmission X-ray microscopy (STXM) analysis, and in situ STXM humidification experiments, this method was validated using laboratory-generated, atmospherically relevant particles. Then, the hygroscopicity and elemental composition of 15 complex atmospheric particles were analyzed by leveraging quantification of C, N, and O from STXM, and complementary elemental quantification from SEM/EDX. We found three types of hygroscopic responses, and correlated high hygroscopicity with Na and Cl content. The mixing state determined for 158 particles broadly agreed with those of the humidified particles, indicating the potential to infer the atmospheric hygroscopic behavior from a selected subset of particles. These methods offer unique quantitative capabilities to characterize and correlate the hygroscopicity and chemistry of individual submicron atmospheric particles.

  11. Infected dendritic cells are sufficient to mediate the adjuvant activity generated by Venezuelan equine encephalitis virus replicon particles.

    Science.gov (United States)

    Tonkin, Daniel R; Whitmore, Alan; Johnston, Robert E; Barro, Mario

    2012-06-22

    Replicon particles derived from Venezuelan equine encephalitis virus (VEE) are infectious non-propagating particles which act as a safe and potent systemic, mucosal, and cellular adjuvant when delivered with antigen. VEE and VEE replicon particles (VRP) can target multiple cell types including dendritic cells (DCs). The role of these cell types in VRP adjuvant activity has not been previously evaluated, and for these studies we focused on the contribution of DCs to the response to VRP. By analysis of VRP targeting in the draining lymph node, we found that VRP induced rapid recruitment of TNF-secreting monocyte-derived inflammatory dendritic cells. VRP preferentially infected these inflammatory DCs as well as classical DCs and macrophages, with less efficient infection of other cell types. DC depletion suggested that the interaction of VRP with classical DCs was required for recruitment of inflammatory DCs, induction of high levels of many cytokines, and for stable transport of VRP to the draining lymph node. Additionally, in vitro-infected DCs enhanced antigen-specific responses by CD4 and CD8 T cells. By transfer of VRP-infected DCs into mice we showed that these DCs generated an inflammatory state in the draining lymph node similar to that achieved by VRP injection. Most importantly, VRP-infected DCs were sufficient to establish robust adjuvant activity in mice comparable to that produced by VRP injection. These findings indicate that VRP infect, recruit and activate both classical and inflammatory DCs, and those DCs become mediators of the VRP adjuvant activity. Published by Elsevier Ltd.

  12. Direct In Situ Mass Specific Absorption Spectra of Biomass Burning Particles Generated from Smoldering Hard and Softwoods.

    Science.gov (United States)

    Radney, James G; You, Rian; Zachariah, Michael R; Zangmeister, Christopher D

    2017-05-16

    Particles from smoldering biomass burning (BB) represent a major source of carbonaceous aerosol in the terrestrial atmosphere. In this study, mass specific absorption spectra of laboratory-generated smoldering wood particles (SWP) from 3 hardwood and 3 softwood species were measured in situ. Absorption data spanning from λ = 500 to 840 nm were collected using a photoacoustic spectrometer coupled to a supercontinuum laser with a tunable wavelength and bandwidth filter. SWP were size- (electrical mobility) and mass-selected prior to optical characterization allowing data to be reported as mass-specific absorption cross sections (MAC). The median measured MAC at λ = 660 nm for smoldering oak particles was 1.1 (0.57/1.8) × 10-2 m2 g-1 spanning from 83 femtograms (fg) to 517 fg (500 nm ≤ mobility diameter ≤950 nm), MAC values in parentheses are the 16th and 84th percentiles of the measured data (i.e., 1σ). The collection of all six wood species (Oak, Hickory, Mesquite, Western redcedar, Baldcypress, and Blue spruce) had median MAC values ranging from 1.4 × 10-2 m2 g-1 to 7.9 × 10-2 m2 g-1 at λ = 550 nm with absorption Ångström exponents (AAE) between 3.5 and 6.2. Oak, Western redcedar, and Blue spruce possessed statistically similar (p > 0.05) spectra while the spectra of Hickory, Mesquite, and Baldcypress were distinct (p < 0.01) as calculated from a point-by-point analysis using the Wilcox rank-sum test.

  13. New generation of monolithic active pixel sensors for charged particle detection; Developpement d'un capteur de nouvelle generation et son electronique integree pour les collisionneurs futurs

    Energy Technology Data Exchange (ETDEWEB)

    Deptuch, G

    2002-09-01

    Vertex detectors are of great importance in particle physics experiments, as the knowledge of the event flavour is becoming an issue for the physics programme at Future Linear Colliders. Monolithic Active Pixel Sensors (MAPS) based on a novel detector structure have been proposed. Their fabrication is compatible with a standard CMOS process. The sensor is inseparable from the readout electronics, since both of them are integrated on the same, low-resistivity silicon wafer. The basic pixel configuration comprises only three MOS transistors and a diode collecting the charge through thermal diffusion. The charge is generated in the thin non-depleted epitaxial layer underneath the readout electronics. This approach provides, at low cost, a high resolution and thin device with the whole area sensitive to radiation. Device simulations using the ISE-TCAD package have been carried out to study the charge collection mechanism. In order to demonstrate the viability of the technique, four prototype chips have been fabricated using different submicrometer CMOS processes. The pixel gain has been calibrated using a {sup 55}Fe source and the Poisson sequence method. The prototypes have been exposed to high-energy particle beams at CERN. The tests proved excellent detection performances expressed in a single-track spatial resolution of 1.5 {mu}m and detection efficiency close to 100%, resulting from a SNR ratio of more than 30. Irradiation tests showed immunity of MAPS to a level of a few times 10{sup 12} n/cm{sup 2} and a few hundred kRad of ionising radiation. The ideas for future work, including on-pixel signal amplification, double sampling operation and current mode pixel design are present as well. (author)

  14. Online Monitoring of Laser-Generated XUV Radiation Spectra by Surface Reflectivity Measurements with Particle Detectors

    Directory of Open Access Journals (Sweden)

    Andreas Hoffmann

    2017-01-01

    Full Text Available In this contribution, we present a wavelength-sensitive method for the detection of extreme ultraviolet (XUV photon energies between 30 eV and 120 eV. The method is based on 45° reflectivity from either a cesium iodide-coated or an uncoated metal surface, which directs the XUV beam onto an electron or ion detector and its signal is used to monitor the XUV beam. The benefits of our approach are a spectrally sensitive diagnosis of the XUV radiation at the interaction place of time-resolved XUV experiments and the detection of infrared leak light though metal filters in high-harmonic generation (HHG experiments. Both features were tested using spectrally shaped XUV pulses from HHG in a capillary, and we have achieved excellent agreement with XUV spectrometer measurements and reflectivity calculations. Our obtained results are of interest for time-resolved XUV experiments presenting an additional diagnostic directly in the interaction region and for small footprint XUV beamline diagnostics.

  15. Generation of initial kinetic distributions for simulation of long-pulse charged particle beams with high space-charge intensity

    Directory of Open Access Journals (Sweden)

    Steven M. Lund

    2009-11-01

    Full Text Available Self-consistent Vlasov-Poisson simulations of beams with high space-charge intensity often require specification of initial phase-space distributions that reflect properties of a beam that is well adapted to the transport channel—both in terms of low-order rms (envelope properties as well as the higher-order phase-space structure. Here, we first review broad classes of kinetic distributions commonly in use as initial Vlasov distributions in simulations of unbunched or weakly bunched beams with intense space-charge fields including the following: the Kapchinskij-Vladimirskij (KV equilibrium, continuous-focusing equilibria with specific detailed examples, and various nonequilibrium distributions, such as the semi-Gaussian distribution and distributions formed from specified functions of linear-field Courant-Snyder invariants. Important practical details necessary to specify these distributions in terms of standard accelerator inputs are presented in a unified format. Building on this presentation, a new class of approximate initial kinetic distributions are constructed using transformations that preserve linear focusing, single-particle Courant-Snyder invariants to map initial continuous-focusing equilibrium distributions to a form more appropriate for noncontinuous focusing channels. Self-consistent particle-in-cell simulations are employed to show that the approximate initial distributions generated in this manner are better adapted to the focusing channels for beams with high space-charge intensity. This improved capability enables simulations that more precisely probe intrinsic stability properties and machine performance.

  16. A new fuzzy adaptive particle swarm optimization for daily Volt/Var control in distribution networks considering distributed generators

    Energy Technology Data Exchange (ETDEWEB)

    Niknam, Taher [Electronic and Electrical Engineering Department, Shiraz University of Technology, Shiraz (Iran); Firouzi, Bahman Bahmani [Islamic Azad University, MArvdasht Branch (Iran); Ostadi, Amir [Department of Electrical and Computer Engineering, University of Toronto, Toronto (Canada)

    2010-06-15

    This paper presents a novel approach for daily Volt/Var control in distribution systems using Distributed Generation (DG) units. The impact of DG units on Volt/Var control is significant in a distribution network with radial configuration and small X/R ratio. In this paper, a price-based approach is adopted to determine the optimum active and reactive power dispatch for the DG units, the reactive power contribution of the capacitor banks, and the tap settings of the transformers in a day in advance. A fuzzy adaptive particle swarm optimization (FAPSO) method is used to solve the daily Volt/Var control which is a non-linear mixed-integer problem. A mathematical expression of the proposed method and its effectiveness using simulation results are provided. (author)

  17. Internal friction between fluid particles of MHD tangent hyperbolic fluid with heat generation: Using coefficients improved by Cash and Karp

    Science.gov (United States)

    Salahuddin, T.; Khan, Imad; Malik, M. Y.; Khan, Mair; Hussain, Arif; Awais, Muhammad

    2017-05-01

    The present work examines the internal resistance between fluid particles of tangent hyperbolic fluid flow due to a non-linear stretching sheet with heat generation. Using similarity transformations, the governing system of partial differential equations is transformed into a coupled non-linear ordinary differential system with variable coefficients. Unlike the current analytical works on the flow problems in the literature, the main concern here is to numerically work out and find the solution by using Runge-Kutta-Fehlberg coefficients improved by Cash and Karp (Naseer et al., Alexandria Eng. J. 53, 747 (2014)). To determine the relevant physical features of numerous mechanisms acting on the deliberated problem, it is sufficient to have the velocity profile and temperature field and also the drag force and heat transfer rate all as given in the current paper.

  18. Theory of optical second-harmonic generation from a sphere of centrosymmetric material: small-particle limit

    Science.gov (United States)

    Dadap, Jerry I.; Shan, Jie; Heinz, Tony F.

    2004-07-01

    The electromagnetic theory of optical second-harmonic generation from small spherical particles comprised of centrosymmetric material is presented. The interfacial region where the inversion symmetry is broken provides a source of the nonlinearity. This response is described by a general surface nonlinear susceptibility tensor for an isotropic interface. In addition, the appropriate weak bulk terms for an isotropic centrosymmetric medium are introduced. The linear optical response of the sphere and the surrounding region is assumed to be isotropic, but otherwise arbitrary. The analysis is carried out to leading order in the ratio of (a/λ), the particle radius to the wavelength of the incident light, and can be considered as the Rayleigh limit for second-harmonic generation from a sphere. Emission from the sphere arises from both induced electric dipole and electric quadrupole moments at the second-harmonic frequency. The former requires a nonlocal excitation mechanism in which the phase variation of the pump beam across the sphere is considered, while the latter is present for a local-excitation mechanism. The locally excited electric dipole term, analogous to the source for linear Rayleigh scattering, is absent for the nonlinear case because of the overall inversion symmetry of the problem. The second-harmonic field is found to scale as (a/λ)3 and to be completely determined by two effective nonlinear susceptibility coefficients formed as a prescribed combination of the surface and bulk nonlinearities. Characteristic angular and polarization selection rules resulting from the mechanism of the radiation process are presented. Various experimental aspects of the problem are examined, including the expected signal strengths and methods of determining the nonlinear susceptibilities. The spectral characteristics associated with the geometry of a small sphere are also discussed, and distinctive localized plasmon resonances are identified.

  19. Production of radioactive particles for use in environmental studies

    Energy Technology Data Exchange (ETDEWEB)

    Ould-Dada, Z. E-mail: zitouni.ould-dada@foodstandards.gsi.gov.uk; Shaw, G.; Kinnersley, R.B

    2003-07-01

    This paper presents an aerosol generation technique developed to produce dry aerosol particles of various sizes from aqueous solutions of salt. The technique was tested with sodium chloride, lithium carbonate and uranyl acetate at various aqueous concentrations which produced particles in the size range of 0.13-1.37 {mu}m Mass Median Diameter (MMD). The generated aerosols were acceptably monodisperse with a geometric standard deviation of 1.4-2. Both MMD and Mass Median Aerodynamic Diameter (MMAD) increased significantly (p<0.001) with increased concentration of the salt in solution. The technique can also be used to generate aerosols of different chemical species. The results obtained indicate that the system is convenient for use with various aerosol-forming materials, with a stable particle size distribution being maintained for a long period of steady operation. The technique was successfully applied in wind tunnel studies to simulate the release of submicron radioactive particles and their interception by crops, grass and tree canopies. The relevance and application of the technique in other areas of environmental assessment studies is discussed.

  20. Stochastic process variation in deep-submicron CMOS circuits and algorithms

    CERN Document Server

    Zjajo, Amir

    2014-01-01

    One of the most notable features of nanometer scale CMOS technology is the increasing magnitude of variability of the key device parameters affecting performance of integrated circuits. The growth of variability can be attributed to multiple factors, including the difficulty of manufacturing control, the emergence of new systematic variation-generating mechanisms, and most importantly, the increase in atomic-scale randomness, where device operation must be described as a stochastic process. In addition to wide-sense stationary stochastic device variability and temperature variation, existence of non-stationary stochastic electrical noise associated with fundamental processes in integrated-circuit devices represents an elementary limit on the performance of electronic circuits. In an attempt to address these issues, Stochastic Process Variation in Deep-Submicron CMOS: Circuits and Algorithms offers unique combination of mathematical treatment of random process variation, electrical noise and temperature and ne...

  1. Particle-in-cell simulations of Magnetic Field Generation, Evolution, and Reconnection in Laser-driven Plasmas

    Science.gov (United States)

    Matteucci, Jack; Moissard, Clément; Fox, Will; Bhattacharjee, Amitava

    2016-10-01

    The advent of high-energy-density physics facilities has introduced the opportunity to experimentally investigate magnetic field dynamics relevant to both ICF and astrophysical plasmas. Recent experiments have demonstrated magnetic reconnection between colliding plasma plumes, where the reconnecting magnetic fields were self-generated in the plasma by the Biermann battery effect. In this study, we simulate these experiments from first principles using 2-D and 3-D particle-in-cell simulations. Simulations self-consistently demonstrate magnetic field generation by the Biermann battery effect, followed by advection by the Hall effect and ion flow. In 2-D simulations, we find in both the collisionless case and the semi-collisional case, defined by eVi × B >> Rei /ne (where Rei is the electron ion momentum transfer) that quantitative agreement with the generalized Ohm's law is only obtained with the inclusion of the pressure tensor. Finally, we document that significant field is destroyed at the reconnection site by the Biermann term, an inverse, `anti-Biermann' effect, which has not been considered previously in analysis of the experiment. The role of the anti-Biermann effect will be compared to standard reconnection mechanisms in 3-D reconnection simulations. This research used resources of the ORLC Facility at the Oak Ridge National Laboratory, which is supported by the Office of Science of the U.S. DoE under Contract No. DE-AC05-00OR22725.

  2. Effect of short-term regional traffic restriction on urban submicron particulate pollution.

    Science.gov (United States)

    Zhao, Suping; Yu, Ye

    2017-05-01

    During the 2013 and 2015 Lanzhou International Marathon Events (LIME1 and LIME2), the local government made a significant effort to improve traffic conditions and air quality by implementing traffic restriction measures. To fill the gap in information on the effect of short-period (several hours) traffic control on urban air quality, submicron particle size distributions and meteorological data were measured simultaneously during June 2013 and June 2015 in urban Lanzhou. The number and surface area concentrations of particles in the 100-200nm range declined by 67.2% and 65.0% for LIME1 due to traffic control, while they decreased by 39.2% and 37.1% for LIME2. The impact of traffic restriction on air pollution near the sampling site lagged behind the traffic control period for LIME2. In addition, the effect of traffic restriction on air pollution near the sampling site was dependent on the distance between the relative orientation of the sampling site and traffic-restricted zones, as well as meteorological conditions such as wind direction. The influence of traffic restrictions on the particle concentrations differed for different particle sizes. The size range most affected by traffic restriction was 60-200 and 60-300nm for number and surface area concentrations in the urban environment, respectively, while for the particle volume concentration it was the 100-600nm range. This study will provide a basis for implementation of future urban traffic-induced particulate pollution control measures. Copyright © 2016. Published by Elsevier B.V.

  3. Reducing DRIFT Backgrounds with a Submicron Aluminized-Mylar Cathode

    OpenAIRE

    Battat, J. S. R.; Daw, E.; Dorofeev, A.; Ezeribe, A. C.; Fox, J. R.; Gauvreau, J-L.; Gold, M; Harmon, L.; Harton, J.; Lafler, R.; Landers, J.; Lauer, R. J.; Lee, E.R.; Loomba, D.; Lumnah, A.

    2015-01-01

    Background events in the DRIFT-IId dark matter detector, mimicking potential WIMP signals, are predominantly caused by alpha decays on the central cathode in which the alpha particle is completely or partially absorbed by the cathode material. We installed a 0.9 micron thick aluminized-mylar cathode as a way to reduce the probability of producing these backgrounds. We study three generations of cathode (wire, thin-film, and radiologically clean thin-film) with a focus on the ratio of backgrou...

  4. Interaction between submicron COD crystals and renal epithelial cells.

    Science.gov (United States)

    Peng, Hua; Ouyang, Jian-Ming; Yao, Xiu-Qiong; Yang, Ru-E

    2012-01-01

    This study aims to investigate the adhesion characteristics between submicron calcium oxalate dihydrate (COD) with a size of 150 ± 50 nm and African green monkey kidney epithelial cells (Vero cells) before and after damage, and to discuss the mechanism of kidney stone formation. Vero cells were oxidatively injured by hydrogen peroxide to establish a model of injured cells. Scanning electron microscopy was used to observe Vero-COD adhesion. Inductively coupled plasma emission spectrometry was used to quantitatively measure the amount of adhered COD microcrystals. Nanoparticle size analyzer and laser scanning confocal microscopy were performed to measure the change in the zeta potential on the Vero cell surface and the change in osteopontin expression during the adhesion process, respectively. The level of cell injury was evaluated by measuring the changes in malonaldehyde content, and cell viability during the adhesion process. The adhesion capacity of Vero cells in the injury group to COD microcrystals was obviously stronger than that of Vero cells in the control group. After adhesion to COD, cell viability dropped, both malonaldehyde content and cell surface zeta potential increased, and the fluorescence intensity of osteopontin decreased because the osteopontin molecules were successfully covered by COD. Submicron COD further damaged the cells during the adhesion process, especially for Vero cells in the control group, leading to an elevated amount of attached microcrystals. Submicron COD can further damage injured Vero cells during the adhesion process. The amount of attached microcrystals is proportional to the degree of cell damage. The increased amount of microcrystals that adhered to the injured epithelial cells plays an important role in the formation of early-stage kidney stones.

  5. Particle size distribution control of Pt particles used for particle gun

    Science.gov (United States)

    Ichiji, M.; Akiba, H.; Nagao, H.; Hirasawa, I.

    2017-07-01

    The purpose of this study is particle size distribution (PSD) control of submicron sized Pt particles used for particle gun. In this report, simple reaction crystallization is conducted by mixing H2PtCl6 and ascorbic acid. Without the additive, obtained Pt particles have broad PSD and reproducibility of experiment is low. With seeding, Pt particles have narrow PSD and reproducibility improved. Additionally, mean particle diameter of 100-700 nm is controlled by changing seeding amount. Obtained particles are successfully characterized as Pt by XRD results. Moreover, XRD spectra indicate that obtained particles are polycrystals. These experimental results suggest that seeding consumed nucleation, as most nuclei attached on the seed surface. This mechanism virtually restricted nucleation to have narrow PSD can be obtained.

  6. Highly sensitive measurement of submicron waveguides based on Brillouin scattering

    Science.gov (United States)

    Godet, Adrien; Ndao, Abdoulaye; Sylvestre, Thibaut; Beugnot, Jean-Charles; Phan Huy, Kien

    2017-02-01

    Fabrication and characterization of submicron optical waveguides is one of the major challenges in modern photonics, as they find many applications from optical sensors to plasmonic devices. Here we report on a novel technique that allows for a complete and precise characterization of silica optical nanofibers. Our method relies on the Brillouin backscattering spectrum analysis that directly depends on the waveguide geometry. Our method was applied to several fiber tapers with diameter ranging from 500 nm to 3 μm. Results were compared to scanning electron microscopy (SEM) images and numerical simulations with very good agreement and similar sensitivity.

  7. Novel Translucent and Strong Submicron Alumina Ceramics for Dental Restorations.

    Science.gov (United States)

    Zhao, M; Sun, Y; Zhang, J; Zhang, Y

    2017-10-01

    An ideal ceramic restorative material should possess excellent aesthetic and mechanical properties. We hypothesize that the high translucency and strength of polycrystalline ceramics can be achieved through microstructural tailoring. The aim of this study is to demonstrate the superior optical and mechanical properties of a new class of submicron grain-sized alumina ceramics relative to the current state-of-the-art dental ceramic materials. The translucency, the in-line transmission ( TIT) in particular, of these submicron alumina ceramics has been examined with the Rayleigh-Gans-Debye light-scattering model. The theoretical predictions related very well with the measured TIT values. The translucency parameter ( TP) and contrast ratio ( CR) of the newly developed aluminas were measured with a reflectance spectrophotometer on a black-and-white background. For comparison, the TIT, TP, and CR values for a variety of dental ceramics, mostly measured in-house but also cited from the literature, were included. The flexural strength of the aluminas was determined with the 4-point bending test. Our findings have shown that for polycrystalline alumina ceramics, an average grain size <1 µm coupled with a porosity level <0.7% could yield translucency values ( TIT, TP, CR) similar to those of the commercial high-translucency porcelains. These values are far superior to the high-translucency lithium disilicate glass-ceramic and zirconias, including the most translucent cubic-containing zirconias. The strength of these submicron grain-sized aluminas was significantly higher than that of the cubic-containing zirconia (e.g., Zpex Smile) and lithia-based glass-ceramics (e.g., IPS e.max CAD HT). A coarse-grained alumina could also reach a translucency level comparable to that of dental porcelain. However, the relatively low strength of this material has limited its clinical indications to structurally less demanding applications, such as orthodontic brackets. With a combined high

  8. Nano to micro particle size distribution measurement in the fluid by interactive force apparatus for fine particle processing.

    Science.gov (United States)

    Fujita, Toyohisa; Dodbiba, Gjergj; Okaya, Katsunori; Matsuo, Seiji; Wang, Li Pang; Onda, Kana; Otsuki, Akira

    2013-12-01

    The direct measurement of fine particles size distribution of dispersions or coagulations in liquid is important for water purification, fine particles separation for recycling and mineral processing, as well as the new material production. The nano to micro particle size is usually measured by light scattering method; however, it is difficult to measure at high concentration of suspension. Here, a novel dynamical method by using the interactive force measurement between particles in liquid under electric field is used for measuring distribution of fine particle. Three types of nano to submicron particles, that is well-dispersed nano particles, coagulated nano particles and settled submicron particles, have been measured by interactive force measurement method. The particle size distributions are compered with the size distributions of dried particles measured by TEM or SEM. The well-dispersed nano particle size distribution by interactive force measurement is influenced by the nano size surfactant micelles. The size distribution of coagulated nano particles in water is larger than the result by TEM. On the other hand, the submicron nickel particle size distribution is similar with the one analyzed by SEM.

  9. Enhanced hydrophobicity and volatility of submicron aerosols under severe emission control conditions in Beijing

    Science.gov (United States)

    Wang, Yuying; Zhang, Fang; Li, Zhanqing

    2017-04-01

    A series of strict emission control measures were implemented in Beijing and the surrounding seven provinces to ensure good air quality during the 2015 China Victory Day parade, rendering a unique opportunity to investigate anthropogenic impact of aerosol properties. Submicron aerosol hygroscopicity and volatility were measured during and after the control period using a hygroscopic and volatile tandem differential mobility analyzer (H/V-TDMA) system. Three periods, namely, the control clean period (Clean1), the non-control clean period (Clean2), and the non-control pollution period (Pollution), were selected to study the effect of the emission control measures on aerosol hygroscopicity and volatility. Aerosol particles became more hydrophobic and volatile due to the emission control measures. The hygroscopicity parameter (κ) of 40-200 nm particles decreased by 32.0%-8.5% during the Clean1 period relative to the Clean2 period, while the volatile shrink factor (SF) of 40-300 nm particles decreased by 7.5%-10.5%. The emission controls also changed the diurnal variation patterns of both the probability density function of κ (κ-PDF) and the probability density function of SF (SF-PDF). During Clean1 the κ-PDF showed one nearly-hydrophobic (NH) mode for particles in the nucleation mode, which was likely due to the dramatic reduction in industrial emissions of inorganic trace gases. Compared to the Pollution period, particles observed during the Clean1 and Clean2 periods exhibited a more significant non-volatile (NV) mode throughout the day, suggesting a more externally-mixed state particularly for the 150 nm particles. Aerosol hygroscopicities increased as particle sizes increased, with the greatest increases seen during the Pollution period. Accordingly, the aerosol volatility became weaker (i.e., SF increased) during the Clean1 and Clean2 periods, but no apparent trend was observed during the Pollution period. Based on a correlation analysis of the number fractions

  10. Surface modification of amorphous nanosilica particles suppresses nanosilica-induced cytotoxicity, ROS generation, and DNA damage in various mammalian cells

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Tokuyuki [Laboratory of Toxicology and Safety Science, Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Yoshioka, Yasuo, E-mail: yasuo@phs.osaka-u.ac.jp [Laboratory of Toxicology and Safety Science, Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Matsuyama, Keigo; Nakazato, Yasutaro; Tochigi, Saeko; Hirai, Toshiro; Kondoh, Sayuri [Laboratory of Toxicology and Safety Science, Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Nagano, Kazuya [Laboratory of Biopharmaceutical Research, National Institute of Biomedical Innovation, 7-6-8 Saitoasagi, Ibaraki, Osaka 567-0085 (Japan); Abe, Yasuhiro [Cancer Biology Research Center, Sanford Research/USD, 2301 E. 60th Street N, Sioux Falls, SD 57104 (United States); Kamada, Haruhiko; Tsunoda, Shin-ichi [Laboratory of Biopharmaceutical Research, National Institute of Biomedical Innovation, 7-6-8 Saitoasagi, Ibaraki, Osaka 567-0085 (Japan); The Center for Advanced Medical Engineering and Informatics, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Nabeshi, Hiromi [Division of Foods, National Institute of Health Sciences, 1-18-1, Kamiyoga, Setagaya-ku, Tokyo 158-8501 (Japan); Yoshikawa, Tomoaki [Laboratory of Toxicology and Safety Science, Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Tsutsumi, Yasuo, E-mail: ytsutsumi@phs.osaka-u.ac.jp [Laboratory of Toxicology and Safety Science, Graduate School of Pharmaceutical Sciences, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan); Laboratory of Biopharmaceutical Research, National Institute of Biomedical Innovation, 7-6-8 Saitoasagi, Ibaraki, Osaka 567-0085 (Japan); The Center for Advanced Medical Engineering and Informatics, Osaka University, 1-6 Yamadaoka, Suita, Osaka 565-0871 (Japan)

    2012-11-02

    Highlights: Black-Right-Pointing-Pointer There is increasing concern regarding the potential health risks of nanomaterials. Black-Right-Pointing-Pointer We evaluated the effect of surface properties of nanomaterials on cellular responses. Black-Right-Pointing-Pointer We showed that the surface properties play an important in determining its safety. Black-Right-Pointing-Pointer These data provide useful information for producing safer nanomaterials. -- Abstract: Recently, nanomaterials have been utilized in various fields. In particular, amorphous nanosilica particles are increasingly being used in a range of applications, including cosmetics, food technology, and medical diagnostics. However, there is concern that the unique characteristics of nanomaterials might induce undesirable effects. The roles played by the physical characteristics of nanomaterials in cellular responses have not yet been elucidated precisely. Here, by using nanosilica particles (nSPs) with a diameter of 70 nm whose surface was either unmodified (nSP70) or modified with amine (nSP70-N) or carboxyl groups (nSP70-C), we examined the relationship between the surface properties of nSPs and cellular responses such as cytotoxicity, reactive oxygen species (ROS) generation, and DNA damage. To compare the cytotoxicity of nSP70, nSP70-N, or nSP70-C, we examined in vitro cell viability after nSP treatment. Although the susceptibility of each cell line to the nSPs was different, nSP70-C and nSP70-N showed lower cytotoxicity than nSP70 in all cell lines. Furthermore, the generation of ROS and induction of DNA damage in nSP70-C- and nSP70-N-treated cells were lower than those in nSP70-treated cells. These results suggest that the surface properties of nSP70 play an important role in determining its safety, and surface modification of nSP70 with amine or carboxyl groups may be useful for the development of safer nSPs. We hope that our results will contribute to the development of safer nanomaterials.

  11. Modelling size and structure of nanoparticles formed from drying of submicron solution aerosols

    Science.gov (United States)

    Bandyopadhyay, Arpan A.; Pawar, Amol A.; Venkataraman, Chandra; Mehra, Anurag

    2015-01-01

    Drying of submicron solution aerosols, under controlled conditions, has been explored to prepare nanoparticles for drug delivery applications. A computational model of solution drop evaporation is developed to study the evolution of solute gradients inside the drop and predict the size and shell thickness of precipitating nanoparticles. The model considers evaporation as a two-stage process involving droplet shrinkage and shell growth. It was corroborated that droplet evaporation rate controls the solute distribution within a droplet and the resulting particle structure (solid or shell type). At higher gas temperatures, rapid build-up of solute near drop surface from high evaporation rates results in early attainment of critical supersaturation solubility and a steeper solute gradient, which favours formation of larger, shell-type particles. At lower gas temperatures, formation of smaller, solid nanoparticles is indicated. The computed size and shell thickness are in good agreement with experimentally prepared lipid nanoparticles. This study indicates that solid or shell structure of precipitated nanoparticles is strongly affected by evaporation rate, while initial solute concentration in the precursor solution and atomized droplet size affect shell thickness. For the gas temperatures considered, evaporative cooling leads to droplet temperature below the melting point of the lipid solute. Thus, we conclude that control over nanoparticle size and structure, of thermolabile precursor materials suitable for drug delivery, can be achieved by controlling evaporation rates, through selection of aerosol processing conditions.

  12. Chemical compositions, sources and evolution processes of the submicron aerosols in Nanjing, China during wintertime

    Science.gov (United States)

    Wu, Y.; He, Y.; Ge, X.; Wang, J.; Yu, H.; Chen, M.

    2016-12-01

    Elevated atmospheric particulate matter pollution is one of the most significant environmental issues in the Yangtze River Delta (YRD), China. Thus it is important to unravel the characteristics, sources and evolution processes of the ambient aerosols in order to improve the air quality. In this study, we report the real-time monitoring results on submicron aerosol particles (PM1) in suburban Nanjing during wintertime of 2015, using an Aerodyne soot particle aerosol mass spectrometer (SP-AMS). This instrument allows the fast measurement of refractory black carbon simultaneously with other aerosol components. Results show that organics was on average the most abundant species of PM1 (25.9%), but other inorganic species, such as nitrate (23.7%) and sulfate (23.3%) also comprised large mass fractions. As the sampling site is heavily influenced by various sources including industrial, traffic and other anthropogenic emissions, etc., six organic aerosol (OA) factors were identified from Positive matrix factorization (PMF) analysis of the SP-AMS OA mass spectra. These factors include three primary OA factors - a hydrocarbon-like OA, an industry-related OA (IOA) and a cooking OA (COA), and three secondary OA factors, i.e., a local OOA (LSOA), a semi-volatile OOA (SV-OOA) and a low-volatility OOA (LV-OOA). Overall, the primary organic aerosol (POA) (HOA, IOA and COA) dominated the total OA mass. Behaviors and evolution processes of these OA factors will be discussed in combining with the other supporting data.

  13. Generation of quantum beams in large clusters irradiated by Super-Intense, high - contrast femtosecond laser pulses

    Energy Technology Data Exchange (ETDEWEB)

    Faenov, A.Ya.; Pikuz, T.A. [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Kyoto (Japan); Joint Institute for High Temperatures RAS, Moscow (Russian Federation); Fukuda, Y.; Nakamura, T.; Bulanov, S.V.; Hayashi, Y.; Kotaki, H.; Pirozhkov, A.S.; Kawachi, T.; Kando, M. [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Kyoto (Japan); Skobelev, I.Yu.; Fortov, V.E. [Joint Institute for High Temperatures RAS, Moscow (Russian Federation); Chen, L.M.; Zhang, L.; Yan, W.C.; Yuan, D.W.; Mao, J.Y.; Wang, Z.H.; Ma, J.L. [Institute of Physics, Chinese Academy of Sciences, Beijing (China); Kato, Y. [The Graduate School for the Creation of New Photonics Industries, Hamamatsu, Shizuoka (Japan)

    2013-02-15

    A short review of our experimental studies on generation of photon and particle beams in submicron clusters irradiated by intense, high-contrast ({proportional_to} 10{sup 8}-10{sup 10}) femtosecond laser pulses is presented. It is shown that highlyefficient laser-cluster interaction allows creating bright sources of X-ray, high-energy electron and ion beams. The examples of applications of femtosecond-laser-produced cluster plasmas (FLPCP) for X-ray and ion beams radiography are presented. (copyright 2013 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  14. Particle Emissions from Domestic Gas Cookers

    DEFF Research Database (Denmark)

    Glarborg, Peter; Livbjerg, Hans; Wagner, Ayten Yilmaz

    2010-01-01

    The authors experimentally studied the formation of submicron particles from a domestic gas cooker in a compartment free from external particle sources. The effects of fuel (methane, natural gas, odorant-free natural gas), primary aeration, flow rate, and fuel sulphur content on particle emissions...... of the emitted particles were found to have a mean value of about 7 nm for partially premixed flames, increasing to ∼10 nm for nonpremixed flames. The quantity of primary air had a strong impact on the particle emissions, showing a minimum at a primary aeration level of 60-65%. Presence of sulphur in small...

  15. Spherical bioactive glass particles and their interaction with human mesenchymal stem cells in vitro.

    Science.gov (United States)

    Labbaf, Sheyda; Tsigkou, Olga; Müller, Karin H; Stevens, Molly M; Porter, Alexandra E; Jones, Julian R

    2011-02-01

    Sub-micron particles of bioactive glass (SMBGs) with composition 85 mol% SiO(2) and 15 mol% CaO were synthesised and characterised. Bioactivity was demonstrated by the formation of calcium apatite following 5 days immersion in simulated body fluid (SBF). The effect of a 24 h exposure of SMBGs (100 μg/ml, 150 μg/ml, 200 μg/ml) to human mesenchymal stem cells (hMSCs) on cell viability, metabolic activity and proliferation were determined using the LIVE/DEAD, MTT, total DNA and LDH assays after 1, 4 and 7 days of culture. None of the SMBG concentrations caused significant cytotoxicity at 1 and 4 days, but the doses of 150 and 200 μg/ml significantly decreased hMSC metabolic activity after 7 days of culture. Cell proliferation decreased as SMBG concentration increased; however none of the SMBGs tested had a significant effect on DNA quantity compared to the control. Confocal microscopy confirmed cellular uptake and localisation of the SMBGs in the hMSC cytoskeleton. Transmission electron microscopy revealed that the SMBGs localised inside the cell cytoplasm and cell endosomes. These findings are important for assessing the toxicity of sub-micron particles that may either be used as injectables for bone regeneration or generated by wear or degradation of bioactive glass scaffolds. Copyright © 2010 Elsevier Ltd. All rights reserved.

  16. Large-scale self-assembly of uniform submicron silver sulfide material driven by precise pressure control

    Science.gov (United States)

    Qi, Juanjuan; Chen, Ke; Zhang, Shuhao; Yang, Yun; Guo, Lin; Yang, Shihe

    2017-03-01

    The controllable self-assembly of nanosized building blocks into larger specific structures can provide an efficient method of synthesizing novel materials with excellent properties. The self-assembly of nanocrystals by assisted means is becoming an extremely active area of research, because it provides a method of producing large-scale advanced functional materials with potential applications in the areas of energy, electronics, optics, and biologics. In this study, we applied an efficient strategy, namely, the use of ‘pressure control’ to the assembly of silver sulfide (Ag2S) nanospheres with a diameter of approximately 33 nm into large-scale, uniform Ag2S sub-microspheres with a size of about 0.33 μm. More importantly, this strategy realizes the online control of the overall reaction system, including the pressure, reaction time, and temperature, and could also be used to easily fabricate other functional materials on an industrial scale. Moreover, the thermodynamics and kinetics parameters for the thermal decomposition of silver diethyldithiocarbamate (Ag(DDTC)) are also investigated to explore the formation mechanism of the Ag2S nanosized building blocks which can be assembled into uniform sub-micron scale architecture. As a method of producing sub-micron Ag2S particles by means of the pressure-controlled self-assembly of nanoparticles, we foresee this strategy being an efficient and universally applicable option for constructing other new building blocks and assembling novel and large functional micromaterials on an industrial scale.

  17. Infected dendritic cells are sufficient to mediate the adjuvant activity generated by Venezuelan equine encephalitis virus replicon particles

    OpenAIRE

    Tonkin, Daniel R; Whitmore, Alan; Johnston, Robert E; Barro, Mario

    2012-01-01

    Replicon particles derived from Venezuelan equine encephalitis virus (VEE) are infectious non-propagating particles which act as a safe and potent systemic, mucosal, and cellular adjuvant when delivered with antigen. VEE and VEE replicon particles (VRP) can target multiple cell types including dendritic cells (DCs). The role of these cell types in VRP adjuvant activity has not been previously evaluated, and for these studies we focused on the contribution of DCs to the response to VRP. By ana...

  18. Parallel nanostructuring of GeSbTe film with particle mask

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Z.B.; Hong, M.H.; Wang, Q.F.; Chong, T.C. [Data Storage Institute, DSI Building, 5 Engineering Drive 1, 117608, Singapore (Singapore); Department of Electrical and Computer Engineering, National University of Singapore, 119260, Singapore (Singapore); Luk' yanchuk, B.S.; Huang, S.M.; Shi, L.P. [Data Storage Institute, DSI Building, 5 Engineering Drive 1, 117608, Singapore (Singapore)

    2004-09-01

    Parallel nanostructuring of a GeSbTe film may significantly improve the recording performance in data storage. In this paper, a method that permits direct and massively parallel nanopatterning of the substrate surface by laser irradiation is investigated. Polystyrene spherical particles were deposited on the surface in a monolayer array by self-assembly. The array was then irradiated with a 248-nm KrF laser. A sub-micron nanodent array can be obtained after single-pulse irradiation. These nanodents change their shapes at different laser energies. The optical near-field distribution around the particles was calculated according to the exact solution of the light-scattering problem. The influence of the presence of the substrate on the optical near field was also studied. The mechanisms for the generation of the nanodent structures are discussed. (orig.)

  19. One year online chemical speciation of submicron particulate matter (PM1) sampled at a French industrial and coastal site

    Science.gov (United States)

    Zhang, Shouwen; Riffault, Véronique; Dusanter, Sébastien; Augustin, Patrick; Fourmentin, Marc; Delbarre, Hervé

    2015-04-01

    The harbor of Dunkirk (Northern France) is surrounded by different industrial plants (metallurgy, petrochemistry, food processing, power plant, etc.), which emit gaseous and particulate pollutants such as Volatile Organic Compounds (VOCs), oxides of nitrogen (NOx) and sulfur (SO2), and submicron particles (PM1). These emissions are poorly characterized and their impact on neighboring urban areas has yet to be assessed. Studies are particularly needed in this type of complex environments to get a better understanding of PM1sources, especially from the industrial sector, their temporal variability, and their transformation. Several instruments, capable of real-time measurements (temporal resolution ≤ 30 min), were deployed at a site located downwind from the industrial area of Dunkirk for a one-year duration (July 2013-September 2014). An Aerosol Chemical Speciation Monitor (ACSM) and an Aethalometer monitored the main chemical species in the non-refractory submicron particles and black carbon, respectively. Concomitant measurements of trace gases and wind speed and direction were also performed. This dataset was analyzed considering four wind sectors, characteristics of marine, industrial, industrial-urban, and urban influences, and the different seasons. We will present a descriptive analysis of PM1, showing strong variations of ambient concentrations, as well as evidences of SO2 to SO4 gas-particle conversion when industrial plumes reached the monitoring site. The organic fraction measured by ACSM (37% of the total mass on average) was analyzed using a source-receptor model based on Positive Matrix Factorization (PMF) to identify chemical signatures of main emission sources and to quantify the contribution of each source to the PM1 budget given the wind sector. Four main factors were identified: hydrocarbon organic aerosol (HOA), oxygenated organic aerosol (OOA), biomass burning organic aerosol (BBOA) and cooking-like organic aerosol (COA). Overall, the total PM

  20. Physico-chemical and optical properties of combustion-generated particles from coal-fired power plant, automobile and ship engine and charcoal kiln.

    Science.gov (United States)

    Kim, Hwajin

    2015-04-01

    Similarities and differences in physico-chemical and optical properties of combustion generated particles from various sources were investigated. Coal-fired power plant, charcoal kiln, automobile and ship engine were major sources, representing combustions of coal, biomass and two different types of diesel, respectively. Scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and energy-dispersive X-ray spectroscopy (EDX) equipped with both SEM and HRTEM were used for physico-chemical analysis. Light absorbing properties were assessed using a spectrometer equipped with an integrating sphere. Particles generated from different combustion sources and conditions demonstrate great variability in their morphology, structure and composition. From coal-fired power plant, both fly ash and flue gas were mostly composed of heterogeneously mixed mineral ash spheres, suggesting that the complete combustion was occurred releasing carbonaceous species out at high temperature (1200-1300 °C). Both automobile and ship exhausts from diesel combustions show typical features of soot: concentric circles comprised of closely-packed graphene layers. However, heavy fuel oil (HFO) combusted particles from ship exhaust demonstrate more complex compositions containing different morphology of particles other than soot, e.g., spherical shape of char particles composed of minerals and carbon. Even for the soot aggregates, particles from HFO burning have different chemical compositions; carbon is dominated but Ca (29.8%), S (28.7%), Na(1%), and Mg(1%) are contained, respectively which were not found from particles of automobile emission. This indicates that chemical compositions and burning conditions are significant to determine the fate of particles. Finally, from biomass burning, amorphous and droplet-like carbonaceous particles with no crystallite structure are observed and they are generally formed by the condensation of low volatile species at low

  1. Chemical strategies for die/wafer submicron alignment and bonding.

    Energy Technology Data Exchange (ETDEWEB)

    Martin, James Ellis; Baca, Alicia I.; Chu, Dahwey; Rohwer, Lauren Elizabeth Shea

    2010-09-01

    This late-start LDRD explores chemical strategies that will enable sub-micron alignment accuracy of dies and wafers by exploiting the interfacial energies of chemical ligands. We have micropatterned commensurate features, such as 2-d arrays of micron-sized gold lines on the die to be bonded. Each gold line is functionalized with alkanethiol ligands before the die are brought into contact. The ligand interfacial energy is minimized when the lines on the die are brought into registration, due to favorable interactions between the complementary ligand tails. After registration is achieved, standard bonding techniques are used to create precision permanent bonds. We have computed the alignment forces and torque between two surfaces patterned with arrays of lines or square pads to illustrate how best to maximize the tendency to align. We also discuss complex, aperiodic patterns such as rectilinear pad assemblies, concentric circles, and spirals that point the way towards extremely precise alignment.

  2. Submicron Plasticity: Yield Stress, Dislocation Avalanches, and Velocity Distribution

    Science.gov (United States)

    Ispánovity, Péter Dusán; Groma, István; Györgyi, Géza; Csikor, Ferenc F.; Weygand, Daniel

    2010-08-01

    The existence of a well-defined yield stress, where a macroscopic crystal begins to plastically flow, has been a basic observation in materials science. In contrast with macroscopic samples, in microcrystals the strain accumulates in random bursts, which makes controlled plastic formation difficult. Here we study by 2D and 3D simulations the plastic deformation of submicron objects under increasing stress. We show that, while the stress-strain relation of individual samples exhibits jumps, its average and mean deviation still specify a well-defined critical stress. The statistical background of this phenomenon is analyzed through the velocity distribution of dislocations, revealing a universal cubic decay and the appearance of a shoulder due to dislocation avalanches.

  3. Microscopic methods in analysis of submicron phospholipid dispersions

    Directory of Open Access Journals (Sweden)

    Płaczek Marcin

    2016-03-01

    Full Text Available Microscopy belongs to the group of tests, used in pharmaceutical technology, that despite the lapse of time and the development of new analytical methods, still remain irreplaceable for the characterization of dispersed drug dosage forms (e.g., suspensions and emulsions. To obtain complete description of a specific drug formulation, such as parenteral colloidal products, a combination of different microscopic techniques is sometimes required. Electron microscopy methods are the most useful ones; however, even such basic methods as optical microscopy may be helpful for determination of some properties of a sample. The publication explicates the most popular microscopical techniques used nowadays for characterization of the morphology of nanoparticles suspended in pharmaceutical formulations; ad vantages and disadvantages of these methods are also discussed. Parenteral submicron formulations containing lecithin or a particular phospholipid were chosen as examples.

  4. Facile synthesis and stable cycling ability of hollow submicron silicon oxide–carbon composite anode material for Li-ion battery

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Joong-Yeon; Nguyen, Dan Thien [Department of Fine Chemical Engineering & Applied Chemistry, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Kang, Joon-Sup [Department of Energy Science and Technology, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Song, Seung-Wan, E-mail: swsong@cnu.ac.kr [Department of Fine Chemical Engineering & Applied Chemistry, Chungnam National University, Daejeon 305-764 (Korea, Republic of); Department of Energy Science and Technology, Chungnam National University, Daejeon 305-764 (Korea, Republic of)

    2015-06-05

    Highlights: • Hollow submicron SiO{sub 2}–carbon composite material was synthesized using Si{sup 4+}-citrate chelation. • Composite material possessed a homogeneous distribution of SiO{sub 2} and carbon. • Composite electrode delivered ⩾600 mAh/g with a stable cycling stability. • This materials design and synthesis provides a useful platform for scalable production. - Abstract: Advanced SiO{sub 2}–carbon composite anode active material for lithium-ion battery has been synthesized through a simple chelation of silicon cation with citrate in a glyme-based solvent. The resultant composite material demonstrates a homogeneous distribution of constituents over the submicron particles and a unique hollow spherical microstructure, which provides an enhanced electrical conductivity and better accommodation of volume change of silicon during electrochemical charge–discharge cycling, respectively. As a result, the composite electrode exhibits a high cycling stability delivering the capacity retention of 91% at the 100th cycle and discharge capacities of 662–602 mAh/g and coulombic efficiencies of 99.8%. This material synthesis is scalable and cost-effective in preparing various submicron or micron composite electrode materials.

  5. Measurement of dark, particle-generated superoxide and hydrogen peroxide production and decay in the subtropical and temperate North Pacific Ocean

    Science.gov (United States)

    Roe, Kelly L.; Schneider, Robin J.; Hansel, Colleen M.; Voelker, Bettina M.

    2016-01-01

    Reactive oxygen species (ROS), which include the superoxide radical (O2-) and hydrogen peroxide (H2O2), are thought to be generated mostly through photochemical reactions and biological activity in seawater and can influence trace metal speciation in the ocean. This study reports the results of an intercomparison of two methods to measure particle-generated [O2-] in seawater samples, as well as measurements of particle-generated O2- and H2O2 concentrations, decay kinetics, and dark production rates in seawater samples at Station ALOHA and (O2- only) in the southern California Current Ecosystem. O2- was measured using two different methods relying on chemiluminescence detection. The first method measured the difference between steady-state [O2-] in filtered and unfiltered seawater, while the second method (standard method) measured O2- decay to baseline in freshly filtered seawater. Because both methods detected [O2-] relative to the background signal from filtered seawater, both should have measured [O2-] generated by particles (presumably biota). However, the O2- concentrations determined by the first method were always much smaller than those obtained from the second (standard) method. Follow-up laboratory and field experiments showed that the increased signal in the standard method was due to a filtration artifact that could neither be eliminated nor consistently accounted for under the tested conditions. We therefore recommend the first method for measuring particle-generated [O2-]. Measured by this method, Station ALOHA had particle-generated O2- concentrations that ranged from undetectable to 0.02 nM, with production rates less than 0.6 nM hr-1 and decay rate coefficients from 0.003 to 0.014 s-1. The southern California Current Ecosystem had particle-generated O2- concentrations that ranged from undetectable to 0.05 nM, with production rates up to 4.7 nM hr-1 and decay rate coefficients from 0.006 to 0.017 s-1. H2O2 concentrations were measured by

  6. Low density lipoprotein peptide conjugated submicron emulsions for combating prostate cancer.

    Science.gov (United States)

    Sun, Pengchao; Zhang, Nan; Hua, Haiying; Liang, Qian; Zhang, Xuexiao; Sun, Qian; Zhao, Yongxing

    2017-02-01

    Submicron emulsions (SEs) is an advanced formulation that possesses good biocompatibility, high loading of hydrophobic drugs, and good stability through autoclave sterilization. To enhance tumor targeting and tumor cell uptake, SEs could be modified with positive charge and targeting moieties. In the present study, three formulations were prepared: Docetaxel-loaded SEs (DocSEs), cationic DocSEs (DocCSEs), and low density lipoprotein receptor (LDLR) targeted peptide-RLT (CEKLKEAFRLTRKRGLKLA) modified DocCSEs (RLT-DocCSEs). The optimized RLT-DocCSEs showed a particle size 182.2±10nm, a zeta potential 39.62±2.41mV, and a loading efficiency of Docetaxel (Doc) 98%. RLT-DocCSEs demonstrated sustained release in 96h and was stable for two months at 4°C. Compared to DocSEs and DocCSEs, RLT-DocCSEs caused significantly more PC-3 cell inhibition and cell apoptosis. RLT-DocCSEs also showed more cellular uptake and slower cellular elimination than that of DocSEs and DocCSEs. The present study indicated RLT-DocCSEs could be a potential formulation for injection of anti-cancer therapeutics with increased tumor targeting and anti-tumor efficacy. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  7. A new circuit technique for reduced leakage current in Deep Submicron CMOS technologies

    Directory of Open Access Journals (Sweden)

    A. Schmitz

    2005-01-01

    Full Text Available Modern CMOS processes in the Deep Submicron regime are restricted to supply voltages below 2 volts and further to account for the transistors' field strength limitations and to reduce the power per logic gate. To maintain the high switching performance, the threshold voltage must be scaled according with the supply voltage. However, this leads to an increased subthreshold current of the transistors in standby mode (VGS=0. Another source of leakage is gate current, which becomes significant for gate oxides of 3nm and below. We propose a Self-Biasing Virtual Rails (SBVR - CMOS technique which acts like an adaptive local supply voltage in case of standby mode. Most important sources of leakage currents are reduced by this technique. Moreover, SBVR-CMOS is capable of conserving stored information in sleep mode, which is vital for memory circuits. Memories are exposed to radiation causing soft errors. This well-known problem becomes even worse in standby mode of typical SRAMs, that have low driving performance to withstand alpha particle hits. In this paper, a 16-transistor SRAM cell is proposed, which combines the advantage of extremely low leakage currents with a very high soft error stability.

  8. Immunogenicity Studies of Bivalent Inactivated Virions of EV71/CVA16 Formulated with Submicron Emulsion Systems

    Directory of Open Access Journals (Sweden)

    Chih-Wei Lin

    2014-01-01

    Full Text Available We assessed two strategies for preparing candidate vaccines against hand, foot, and mouth disease (HFMD caused mainly by infections of enterovirus (EV 71 and coxsackievirus (CV A16. We firstly design and optimize the potency of adjuvant combinations of emulsion-based delivery systems, using EV71 candidate vaccine as a model. We then perform immunogenicity studies in mice of EV71/CVA16 antigen combinations formulated with PELC/CpG. A single dose of inactivated EV71 virion (0.2 μg emulsified in submicron particles was found (i to induce potent antigen-specific neutralizing antibody responses and (ii consistently to elicit broad antibody responses against EV71 neutralization epitopes. A single dose immunogenicity study of bivalent activated EV71/CVA16 virion formulated with either Alum or PELC/CpG adjuvant showed that CVA16 antigen failed to elicit CVA16 neutralizing antibody responses and did not affect EV71-specific neutralizing antibody responses. A boosting dose of emulsified EV71/CVA16 bivalent vaccine candidate was found to be necessary to achieve high seroconversion of CVA16-specific neutralizing antibody responses. The current results are important for the design and development of prophylactic vaccines against HFMD and other emerging infectious diseases.

  9. Measurement and quality control of a new generation of particle accelerator and detectors Geological and thermal influence on the particle beam position

    CERN Document Server

    Krauter, L

    2004-01-01

    At CERN (European Organization for Nuclear Research, Geneva, Switzerland) the most powerful particle collider in the world is under construction. It will be the first time that an accelerator with a diameter of 9 km runs totally on superconducting magnets. Because of the large size of this machine, the influence of the movement from the plate tectonic is not negligible for the alignment of the magnets. Another negative influence on the precision of the centre of the magnetic field is the warping of the magnet caused by the thermal contraction during the cooling down process from room temperature to the operating temperature of 1.9 K.

  10. Mechanically Robust, Stretchable Solar Absorbers with Submicron-Thick Multilayer Sheets for Wearable and Energy Applications.

    Science.gov (United States)

    Lee, Hye Jin; Jung, Dae-Han; Kil, Tae-Hyeon; Kim, Sang Hyeon; Lee, Ki-Suk; Baek, Seung-Hyub; Choi, Won Jun; Baik, Jeong Min

    2017-05-31

    A facile method to fabricate a mechanically robust, stretchable solar absorber for stretchable heat generation and an enhanced thermoelectric generator (TEG) is demonstrated. This strategy is very simple: it uses a multilayer film made of titanium and magnesium fluoride optimized by a two-dimensional finite element frequency-domain simulation, followed by the application of mechanical stresses such as bending and stretching to the film. This process produces many microsized sheets with submicron thickness (∼500 nm), showing great adhesion to any substrates such as fabrics and polydimethylsiloxane. It exhibits a quite high light absorption of approximately 85% over a wavelength range of 0.2-4.0 μm. Under 1 sun illumination, the solar absorber on various stretchable substrates increased the substrate temperature to approximately 60 °C, irrespective of various mechanical stresses such as bending, stretching, rubbing, and even washing. The TEG with the absorber on the top surface also showed an enhanced output power of 60%, compared with that without the absorber. With an incident solar radiation flux of 38.3 kW/m 2 , the output power significantly increased to 24 mW/cm 2 because of the increase in the surface temperature to 141 °C.

  11. Scalable Sub-micron Patterning of Organic Materials Toward High Density Soft Electronics.

    Science.gov (United States)

    Kim, Jaekyun; Kim, Myung-Gil; Kim, Jaehyun; Jo, Sangho; Kang, Jingu; Jo, Jeong-Wan; Lee, Woobin; Hwang, Chahwan; Moon, Juhyuk; Yang, Lin; Kim, Yun-Hi; Noh, Yong-Young; Jaung, Jae Yun; Kim, Yong-Hoon; Park, Sung Kyu

    2015-09-28

    The success of silicon based high density integrated circuits ignited explosive expansion of microelectronics. Although the inorganic semiconductors have shown superior carrier mobilities for conventional high speed switching devices, the emergence of unconventional applications, such as flexible electronics, highly sensitive photosensors, large area sensor array, and tailored optoelectronics, brought intensive research on next generation electronic materials. The rationally designed multifunctional soft electronic materials, organic and carbon-based semiconductors, are demonstrated with low-cost solution process, exceptional mechanical stability, and on-demand optoelectronic properties. Unfortunately, the industrial implementation of the soft electronic materials has been hindered due to lack of scalable fine-patterning methods. In this report, we demonstrated facile general route for high throughput sub-micron patterning of soft materials, using spatially selective deep-ultraviolet irradiation. For organic and carbon-based materials, the highly energetic photons (e.g. deep-ultraviolet rays) enable direct photo-conversion from conducting/semiconducting to insulating state through molecular dissociation and disordering with spatial resolution down to a sub-μm-scale. The successful demonstration of organic semiconductor circuitry promise our result proliferate industrial adoption of soft materials for next generation electronics.

  12. Mass distribution and elemental analysis of the resultant atmospheric aerosol particles generated in controlled biomass burning processes

    Science.gov (United States)

    Ordou, N.; Agranovski, I. E.

    2017-12-01

    Air contamination resulting from bushfires is becoming increasingly important research question, as such disasters frequently occur in many countries. The objectives of this project were focused on physical and chemical characterisations of particulate emission resulting from burning of common representatives of Australian vegetation under controlled laboratory conditions. It was found that leaves are burned mostly with flaming phase and producing black smoke resulting in larger particles compared to white smoke in case of branches and grass, dominated by smouldering phase, producing finer particles. Following elemental analysis determined nine main elements in three different size fractions of particulate matter for each category of burning material, ranging from 14.1 μm to particle sizes below 2.54 μm. Potassium was found to be one of the main biomass markers, and sulphur was the ubiquitous element among the smoke particles followed by less prevalent trace elements like Na, Al, Mg, Zn, Si, Ca, and Fe.

  13. Generation of Kappa-like Distribution due to energization of charged particles by time-dependent chaotic magnetic field

    Science.gov (United States)

    Dasgupta, B.; Heerikhuisen, J.; Janaki, M. S.; Shaw, P.; Samanta, S.; Doyale, C. J.

    2016-12-01

    It can be argued that magnetic fields which depend on the three spatial coordinates give rise to field lines that have chaotic structure. Such chaotic magnetic fields are omnipresent in astrophysical scenarios. We have previously also shown that the force-free magnetic field, which are prevalent in solar atmosphere, solar wind etc can be chaotic. Here we have demonstrated by extensive numerical simulation that charged particles moving through time-dependent chaotic magnetic fields appear to be energized indefinitely. Starting with a large number of charged particles with an initial Gaussian or delta function velocity distributions and subjected these particles to energization by force-free magnetic fields with arbitrary time dependence. We find that the final distributions of the energized particles always correspond to a kappa-like distribution with a prominent high energy tail. We present our results for various initial conditions and parameters, corresponding to a range of space environments.

  14. LAMMPS integrated materials engine (LIME) for efficient automation of particle-based simulations: application to equation of state generation

    Science.gov (United States)

    Barnes, Brian C.; Leiter, Kenneth W.; Becker, Richard; Knap, Jaroslaw; Brennan, John K.

    2017-07-01

    We describe the development, accuracy, and efficiency of an automation package for molecular simulation, the large-scale atomic/molecular massively parallel simulator (LAMMPS) integrated materials engine (LIME). Heuristics and algorithms employed for equation of state (EOS) calculation using a particle-based model of a molecular crystal, hexahydro-1,3,5-trinitro-s-triazine (RDX), are described in detail. The simulation method for the particle-based model is energy-conserving dissipative particle dynamics, but the techniques used in LIME are generally applicable to molecular dynamics simulations with a variety of particle-based models. The newly created tool set is tested through use of its EOS data in plate impact and Taylor anvil impact continuum simulations of solid RDX. The coarse-grain model results from LIME provide an approach to bridge the scales from atomistic simulations to continuum simulations.

  15. Studies on solvatochromic properties of aminophenylstyryl-quinolinum dye, LDS 798, and its application in studying submicron lipid based structure.

    Science.gov (United States)

    Sarkar, Pabak; Luchowski, Rafal; Raut, Sangram; Sabnis, Nirupama; Remaley, Alan; Lacko, Andras G; Thamake, Sanjay; Gryczynski, Zygmunt; Gryczynski, Ignacy

    2010-12-01

    The styryl group of dyes has been used in cellular studies for over 20 years because of their solvatochromic and/or electrochromic properties. Here we report characterization of solubility and solvatochromic properties of a near infra-red styryl dye, styryl 11 or LDS 798. We have extended our studies to small unilamellar vesicles and lipid based nanoparticles and found that solvatochromic properties of this dye used in tandem with fluorescence correlation spectroscopy can be used to efficiently determine the diffusion coefficient and hence the size of the submicron lipid based particles. This technique has the potential to provide essential information about liposomal and vesicular structures and their movement in vitro and in situ. Published by Elsevier B.V.

  16. Pulmonary clearance kinetics and extrapulmonary translocation of seven titanium dioxide nano- and submicron materials following intratracheal administration in rats.

    Science.gov (United States)

    Shinohara, Naohide; Oshima, Yutaka; Kobayashi, Toshio; Imatanaka, Nobuya; Nakai, Makoto; Ichinose, Takayuki; Sasaki, Takeshi; Kawaguchi, Kenji; Zhang, Guihua; Gamo, Masashi

    2015-01-01

    We evaluated and compared the pulmonary clearance kinetics and extrapulmonary translocations of seven titanium dioxide (TiO2) nano- and submicron particles with different characteristics, including size, shape and surface coating. Varying doses of TiO2 nano- and submicron particles dispersed in 0.2% disodium phosphate solution were intratracheally administered to male F344 rats. The rats were euthanized under anesthesia for 3, 28 and 91 days after administration. Ti levels in pulmonary and various extrapulmonary organs were determined using inductively coupled plasma-sector field mass spectrometry (ICP-SFMS). The lungs, including bronchoalveolar lavage fluid (BALF), contained 55-89% of the administered TiO2 dose at 3 days after administration. The pulmonary clearance rate constants, estimated using a one-compartment model, were higher after administration of 0.375-2.0 mg/kg body weight (bw) (0.016-0.020/day) than after administration of 3.0-6.0 mg/kg bw (0.0073-0.013/day) for six uncoated TiO2. In contrast, the clearance rate constant was 0.011, 0.0046 and 0.00018/day following administration of 0.67, 2.0 and 6.0 mg/kg bw TiO2 nanoparticle with Al(OH)3 coating, respectively. Translocation of TiO2 from the lungs to the thoracic lymph nodes increased in a time- and dose-dependent manner. Furthermore, the translocation of TiO2 from the lungs to the thoracic lymph nodes after 91 days was higher when Al(OH)3 coated TiO2 was administered (0.93-6.4%), as compared to uncoated TiO2 (0.016-1.8%). Slight liver translocation was observed (kidney, spleen and brain.

  17. Fourier optics along a hybrid optical fiber for Bessel-like beam generation and its applications in multiple-particle trapping.

    Science.gov (United States)

    Kim, Jongki; Jeong, Yoonseob; Lee, Sejin; Ha, Woosung; Shin, Jeon-Soo; Oh, Kyunghwan

    2012-02-15

    Highly efficient Bessel-like beam generation was achieved based on a new all-fiber method that implements Fourier transformation of a micro annular aperture along a concatenated composite optical fiber. The beam showed unique characteristics of tilted washboard optical potential in the transverse plane and sustained a nondiffracting length over 400 μm along the axial direction. Optical trapping of multiple dielectric particles and living Jurkat cells were successfully demonstrated along the axial direction of the beam in the water.

  18. [Study on preparation of intravenous submicron emulsions of Oleum Cinnamomi oil of Miao nationality herbal].

    Science.gov (United States)

    Li, Jiang; Liu, Ying-bo

    2007-11-01

    To study the prescription and preparation of intravenous submicron emulsion of Oleum Cinnamomi oil of Miao nationality herbal. Using the high speed blender mixed round the Oleum Cinnamomi oil with the soybean phospholipids and Pluronic F68 as emulsifier, then using the high pressure homogenizer made the intravenous submicron emulsion of the Oleum Cinnamomi oil and investigate its grain path and distributing. Having been done by using hydroextractor 4,500 r min(-1) 15 minutes the submicron emulsion grain path has well proportioned distribution. The preparation technology is simple and has good stability, so it can be used as a method to make the intravenous submicron emulsion of the Oleum Cinnamomi oil of Miao nationality herbal.

  19. Light emitting diode with high aspect ratio submicron roughness for light extraction and methods of forming

    Science.gov (United States)

    Li, Ting [Ventura, CA

    2011-04-26

    The surface morphology of an LED light emitting surface is changed by applying a reactive ion etch (RIE) process to the light emitting surface. High aspect ratio, submicron roughness is formed on the light emitting surface by transferring a thin film metal hard-mask having submicron patterns to the surface prior to applying a reactive ion etch process. The submicron patterns in the metal hard-mask can be formed using a low cost, commercially available nano-patterned template which is transferred to the surface with the mask. After subsequently binding the mask to the surface, the template is removed and the RIE process is applied for time duration sufficient to change the morphology of the surface. The modified surface contains non-symmetric, submicron structures having high aspect ratio which increase the efficiency of the device.

  20. Light emitting diode with high aspect ratio submicron roughness for light extraction and methods of forming

    Science.gov (United States)

    Li, Ting

    2013-08-13

    The surface morphology of an LED light emitting surface is changed by applying a reactive ion etch (RIE) process to the light emitting surface. High aspect ratio, submicron roughness is formed on the light emitting surface by transferring a thin film metal hard-mask having submicron patterns to the surface prior to applying a reactive ion etch process. The submicron patterns in the metal hard-mask can be formed using a low cost, commercially available nano-patterned template which is transferred to the surface with the mask. After subsequently binding the mask to the surface, the template is removed and the RIE process is applied for time duration sufficient to change the morphology of the surface. The modified surface contains non-symmetric, submicron structures having high aspect ratio which increase the efficiency of the device.

  1. Characteristics and sources of intermediate size particles in recovery boilers : final project report.

    Energy Technology Data Exchange (ETDEWEB)

    Baxter, Larry L. (Brigham Young University, Provo, UT); Shaddix, Christopher R.; Verrill, Christopher L. (Georgia Institute of Technology, Institute of Paper Science and Technology, Atlanta, GA); Wessel, Richard A. (Babcock & Wilcox Company, Barberton, OH)

    2005-02-01

    As part of the U.S. Department of Energy (DOE) Office of Industrial Technologies (OIT) Industries of the Future (IOF) Forest Products research program, a collaborative investigation was conducted on the sources, characteristics, and deposition of particles intermediate in size between submicron fume and carryover in recovery boilers. Laboratory experiments on suspended-drop combustion of black liquor and on black liquor char bed combustion demonstrated that both processes generate intermediate size particles (ISP), amounting to 0.5-2% of the black liquor dry solids mass (BLS). Measurements in two U.S. recovery boilers show variable loadings of ISP in the upper furnace, typically between 0.6-3 g/Nm{sup 3}, or 0.3-1.5% of BLS. The measurements show that the ISP mass size distribution increases with size from 5-100 {micro}m, implying that a substantial amount of ISP inertially deposits on steam tubes. ISP particles are depleted in potassium, chlorine, and sulfur relative to the fuel composition. Comprehensive boiler modeling demonstrates that ISP concentrations are substantially overpredicted when using a previously developed algorithm for ISP generation. Equilibrium calculations suggest that alkali carbonate decomposition occurs at intermediate heights in the furnace and may lead to partial destruction of ISP particles formed lower in the furnace. ISP deposition is predicted to occur in the superheater sections, at temperatures greater than 750 C, when the particles are at least partially molten.

  2. Generation of Helical and Axial Magnetic Fields by the Relativistic Laser Pulses in Under-dense Plasma: Three-Dimensional Particle-in-Cell Simulation

    Science.gov (United States)

    Zheng, Chun-Yang; Zhu, Shao-Ping; He, Xian-Tu

    2002-07-01

    The quasi-static magnetic fields created in the interaction of relativistic laser pulses with under-dense plasmas have been investigated by three-dimensional particle-in-cell simulation. The relativistic ponderomotive force can drive an intense electron current in the laser propagation direction, which is responsible for the generation of a helical magnetic field. The axial magnetic field results from a difference beat of wave-wave, which drives a solenoidal current. In particular, the physical significance of the kinetic model for the generation of the axial magnetic field is discussed.

  3. Emissions, ultra fine particles, and health effects from heavy-duty engines running on first- and second-generation alternative fuels; Gasfoermige und partikulaere Emissionen sowie Umweltwirkungen von Nutzfahrzeugmotoren im Betrieb mit Alternativkraftstoffen der ersten und zweiten Generation

    Energy Technology Data Exchange (ETDEWEB)

    Krahl, J. [Fachhochschule Coburg (Germany); Munach, A.; Grope, N.; Schroeder, O.; Ruschel, Y. [Bundesforschungsanstalt fuer Landwirtschaft, Braunschweig (Germany); Buenger, J. [Ruhr-Univ. Bochum (Germany). Inst. BGFA; Hofmann, L. [Argillon, Redwitz (Germany); Schwarz, S. [IVECO Motorenforschung AG, Arbon (Switzerland)

    2006-07-01

    In Germany and in many European countries biodiesel is a popular substitute for fossil diesel fuel. It is used as neat fuel and as blend component (mainly 5%) to diesel fuel. However, a fuel cannot be considered as environmentally friendly only because it derives from a renewable source. The regulated and some of the most important non-regulated emissions and the impact on human health must be investigated and judged as well. In course of the investigations a heavy-duty engine (emission class Euro 3) was tested to investigate the fuel influence. More precisely, first-generation alternative fuels (biodiesel, rape seed oil), second-generation alternative fuel (gas-to-liquid fuel, GTL), and blends of biodiesel, GTL, and diesel fuel were compared to diesel fuel. Besides the regulated emissions, the focus was on the ultra fine particles. In the European Union, the ultra fine particles are under suspect to induce severe health problems. For the detection of the ultra fine particles, a scanning mobility particle sizer (SMPS) and an electronic low-pressure impactor (ELPI) were used. Additionally, Ames-tests were carried out to determine the mutagenic potency of particulate matter extracts. Moreover, a 1000 hours biodiesel endurance test was accomplished with an Euro 4 test engine equipped with a urea based SCR (selective catalytic reduction) pilot series system. Goal of the test was to investigate how far a concentration of 10 ppm phosphorus can affect the catalyst and therefore the emissions. (orig.)

  4. Impact-disrupted gunshot residue: A sub-micron analysis using a novel collection protocol

    Directory of Open Access Journals (Sweden)

    V. Spathis

    2017-06-01

    Full Text Available The analysis of gunshot residue (GSR has played an integral role within the legal system in relation to shooting cases. With a characteristic elemental composition of lead, antimony, barium, and a typically discriminative spheroidal morphology, the presence and distribution of GSR can aid in firearm investigations. In this experiment, three shots of low velocity rim-fire ammunition were fired over polished silicon collection substrates placed at six intervals over a 100 cm range. The samples were analysed using a Field Emission Gun Scanning Electron Microscope (FEG-SEM in conjunction with an X-flash Energy Dispersive X-ray (EDX detector, allowing for GSR particle analyses of composition and structure at the sub-micron level. The results of this experiment indicate that although classic spheroidal particles are present consistently throughout the entire range of samples their sizes vary significantly, and at certain distances from the firearm particles with an irregular morphology were discerned, forming “impact-disrupted” GSR particles, henceforth colloquially referred to as “splats”. Upon further analysis, trends with regards to the formation of these splat particles were distinguished. An increase in splat frequency was observed starting at 10 cm from the firearm, with 147 mm−2 splat density, reaching a maximal flux at 40 cm (451 mm−2, followed by a gradual decrease to the maximum range sampled. Moreover, the structural morphology of the splats changes throughout the sampling range. At the distances closest to the firearm, molten-looking particles were formed, demonstrating the metallic residues were in a liquid state when their flight path was disrupted. However, at increased distances-primarily where the discharge plume was at maximum dispersion and moving away from the firearm, the residues have had time to cool in-fight resulting in semi-congealed and solid particles that subsequently disrupted upon impact, forming more

  5. SiO2/ZnO Composite Hollow Sub-Micron Fibers: Fabrication from Facile Single Capillary Electrospinning and Their Photoluminescence Properties.

    Science.gov (United States)

    Song, Guanying; Li, Zhenjiang; Li, Kaihua; Zhang, Lina; Meng, Alan

    2017-02-24

    In this work, SiO2/ZnO composite hollow sub-micron fibers were fabricated by a facile single capillary electrospinning technique followed by calcination, using tetraethyl orthosilicate (TEOS), polyvinylpyrrolidone (PVP) and ZnO nanoparticles as raw materials. The characterization results of the scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) spectra indicated that the asprepared composite hollow fibers consisted of amorphous SiO2 and hexagonal wurtzite ZnO. The products revealed uniform tubular structure with outer diameters of 400-500 nm and wall thickness of 50-60 nm. The gases generated and the directional escaped mechanism was proposed to illustrate the formation of SiO2/ZnO composite hollow sub-micron fibers. Furthermore, a broad blue emission band was observed in the photoluminescence (PL) of SiO2/ZnO composite hollow sub-micron fibers, exhibiting great potential applications as blue light-emitting candidate materials.

  6. SiO2/ZnO Composite Hollow Sub-Micron Fibers: Fabrication from Facile Single Capillary Electrospinning and Their Photoluminescence Properties

    Directory of Open Access Journals (Sweden)

    Guanying Song

    2017-02-01

    Full Text Available In this work, SiO2/ZnO composite hollow sub-micron fibers were fabricated by a facile single capillary electrospinning technique followed by calcination, using tetraethyl orthosilicate (TEOS, polyvinylpyrrolidone (PVP and ZnO nanoparticles as raw materials. The characterization results of the scanning electron microscopy (SEM, transmission electron microscopy (TEM, X-ray diffraction (XRD and Fourier transform infrared spectroscopy (FT-IR spectra indicated that the asprepared composite hollow fibers consisted of amorphous SiO2 and hexagonal wurtzite ZnO. The products revealed uniform tubular structure with outer diameters of 400–500 nm and wall thickness of 50–60 nm. The gases generated and the directional escaped mechanism was proposed to illustrate the formation of SiO2/ZnO composite hollow sub-micron fibers. Furthermore, a broad blue emission band was observed in the photoluminescence (PL of SiO2/ZnO composite hollow sub-micron fibers, exhibiting great potential applications as blue light-emitting candidate materials.

  7. Rapid heterogeneous oxidation of organic coatings on submicron aerosols

    Science.gov (United States)

    Lim, C. Y.; Browne, E. C.; Sugrue, R. A.; Kroll, J. H.

    2017-03-01

    Laboratory studies have found that heterogeneous oxidation can affect the composition and loading of atmospheric organic aerosol particles over time scales of several days, but most studies have examined pure organic particles only. In this study, in order to probe the reactivity of organic species confined near the particle surface, the rates and products of the OH-initiated oxidation of pure squalane particles are compared to oxidation of thin coatings of squalane on ammonium sulfate particles. The squalane reaction rate constant shows a linear dependence on the organic surface area-to-volume ratio, with rate constants for coated particles up to 10 times larger than for pure particles. Changes in the carbon oxidation state and fraction of particulate carbon remaining show similar enhancements, implying that heterogeneous oxidation may exhibit a stronger effect on the loadings and properties of organic aerosol than previously estimated from laboratory studies.

  8. Wear particles derived from metal hip implants induce the generation of multinucleated giant cells in a 3-dimensional peripheral tissue-equivalent model.

    Directory of Open Access Journals (Sweden)

    Debargh K Dutta

    Full Text Available Multinucleate giant cells (MGCs are formed by the fusion of 5 to 15 monocytes or macrophages. MGCs can be generated by hip implants at the site where the metal surface of the device is in close contact with tissue. MGCs play a critical role in the inflammatory processes associated with adverse events such as aseptic loosening of the prosthetic joints and bone degeneration process called osteolysis. Upon interaction with metal wear particles, endothelial cells upregulate pro-inflammatory cytokines and other factors that enhance a localized immune response. However, the role of endothelial cells in the generation of MGCs has not been completely investigated. We developed a three-dimensional peripheral tissue-equivalent model (PTE consisting of collagen gel, supporting a monolayer of endothelial cells and human peripheral blood mononuclear cells (PBMCs on top, which mimics peripheral tissue under normal physiological conditions. The cultures were incubated for 14 days with Cobalt chromium alloy (CoCr ASTM F75, 1-5 micron wear particles. PBMC were allowed to transit the endothelium and harvested cells were analyzed for MGC generation via flow cytometry. An increase in forward scatter (cell size and in the propidium iodide (PI uptake (DNA intercalating dye was used to identify MGCs. Our results show that endothelial cells induce the generation of MGCs to a level 4 fold higher in 3-dimentional PTE system as compared to traditional 2-dimensional culture plates. Further characterization of MGCs showed upregulated expression of tartrate resistant alkaline phosphatase (TRAP and dendritic cell specific transmembrane protein, (DC-STAMP, which are markers of bone degrading cells called osteoclasts. In sum, we have established a robust and relevant model to examine MGC and osteoclast formation in a tissue like environment using flow cytometry and RT-PCR. With endothelial cells help, we observed a consistent generation of metal wear particle- induced MGCs

  9. Chemical mapping of proterozoic organic matter at submicron spatial resolution.

    Science.gov (United States)

    Oehler, Dorothy Z; Robert, François; Mostefaoui, Smail; Meibom, Anders; Selo, Madeleine; McKay, David S

    2006-12-01

    A NanoSIMS ion microprobe was used to map the submicron-scale distributions of carbon, nitrogen, sulfur, silicon, and oxygen in organic microfossils and laminae in a thin section of the approximately 0.85 billion year old Bitter Springs Formation of Australia. The data provide clues about the original chemistry of the microfossils, the silicification process, and the biosignatures of specific microorganisms and microbial communities. Chemical maps of fossil unicells and filaments revealed distinct wall- and sheath-like structures enriched in C, N, and S, consistent with their accepted biological origin. Surprisingly, organic laminae, previously considered to be amorphous, also exhibited filamentous and apparently compressed spheroidal structures defined by strong enrichments in C, N, and S. By analogy to NanoSIMS data from the well-preserved microfossils, these structures were interpreted as being of biological origin, most likely representing densely packed remnants of microbial mats. Given that the preponderance of organic matter in Precambrian sediments is similarly "amorphous," our findings indicate that a re-evaluation of ancient specimens via in situ structural, chemical, and isotopic study is warranted. Our analyses have led us to propose new criteria for assessing the biogenicity of problematic kerogenous materials, and, thus, these criteria can be applied to assessments of poorly preserved or fragmentary organic residues in early Archean sediments and any that might occur in meteorites or other extraterrestrial samples.

  10. Controlled motion of domain walls in submicron amorphous wires

    Directory of Open Access Journals (Sweden)

    Mihai Ţibu

    2016-05-01

    Full Text Available Results on the control of the domain wall displacement in cylindrical Fe77.5Si7.5B15 amorphous glass-coated submicron wires prepared by rapid quenching from the melt are reported. The control methods have relied on conical notches with various depths, up to a few tens of nm, made in the glass coating and in the metallic nucleus using a focused ion beam (FIB system, and on the use of small nucleation coils at one of the sample ends in order to apply magnetic field pulses aimed to enhance the nucleation of reverse domains. The notch-based method is used for the first time in the case of cylindrical ultrathin wires. The results show that the most efficient technique of controlling the domain wall motion in this type of samples is the simultaneous use of notches and nucleation coils. Their effect depends on wire diameter, notch depth, its position on the wire length, and characteristics of the applied pulse.

  11. Controlled motion of domain walls in submicron amorphous wires

    Energy Technology Data Exchange (ETDEWEB)

    Ţibu, Mihai; Lostun, Mihaela; Rotărescu, Cristian; Atiţoaie, Alexandru; Lupu, Nicoleta; Óvári, Tibor-Adrian, E-mail: taovari@phys-iasi.ro; Chiriac, Horia [Department of Magnetic Materials and Devices, National Institute of Research and Development for Technical Physics, Iaşi, 700050 (Romania); Allwood, Dan A. [Department of Materials Science and Engineering, University of Sheffield, Sheffield, S1 3JD (United Kingdom)

    2016-05-15

    Results on the control of the domain wall displacement in cylindrical Fe{sub 77.5}Si{sub 7.5}B{sub 15} amorphous glass-coated submicron wires prepared by rapid quenching from the melt are reported. The control methods have relied on conical notches with various depths, up to a few tens of nm, made in the glass coating and in the metallic nucleus using a focused ion beam (FIB) system, and on the use of small nucleation coils at one of the sample ends in order to apply magnetic field pulses aimed to enhance the nucleation of reverse domains. The notch-based method is used for the first time in the case of cylindrical ultrathin wires. The results show that the most efficient technique of controlling the domain wall motion in this type of samples is the simultaneous use of notches and nucleation coils. Their effect depends on wire diameter, notch depth, its position on the wire length, and characteristics of the applied pulse.

  12. Submicron Surface Vibration Profiling Using Doppler Self-Mixing Techniques

    Directory of Open Access Journals (Sweden)

    Tânia Pereira

    2014-01-01

    Full Text Available Doppler self-mixing laser probing techniques are often used for vibration measurement with very high accuracy. A novel optoelectronic probe solution is proposed, based on off-the-shelf components, with a direct reflection optical scheme for contactless characterization of the target’s movement. This probe was tested with two test bench apparatus that enhance its precision performance, with a linear actuator at low frequency (35 µm, 5–60 Hz, and its dynamics, with disc shaped transducers for small amplitude and high frequency (0.6 µm, 100–2500 Hz. The results, obtained from well-established signal processing methods for self-mixing Doppler signals, allowed the evaluation of vibration velocity and amplitudes with an average error of less than 10%. The impedance spectrum of piezoelectric (PZ disc target revealed a maximum of impedance (around 1 kHz for minimal Doppler shift. A bidimensional scan over the PZ disc surface allowed the categorization of the vibration mode (0, 1 and explained its deflection directions. The feasibility of a laser vibrometer based on self-mixing principles and supported by tailored electronics able to accurately measure submicron displacements was, thus, successfully demonstrated.

  13. Enhancements of the refractory submicron aerosol fraction in the Arctic polar vortex: feature or exception?

    Science.gov (United States)

    Weigel, R.; Volk, C. M.; Kandler, K.; Hösen, E.; Günther, G.; Vogel, B.; Grooß, J.-U.; Khaykin, S.; Belyaev, G. V.; Borrmann, S.

    2014-11-01

    In situ measurements with a four-channel stratospheric condensation particle counter (CPC) were conducted at up to 20 km altitude on board the aircraft M-55 Geophysica from Kiruna, Sweden, in January through March (EUPLEX 2003, RECONCILE 2010) and in December (ESSenCe 2011). During all campaigns air masses from the upper stratosphere and mesosphere were subsiding inside the Arctic winter vortex, thus initializing a transport of refractory aerosol into the lower stratosphere (Θ content of nitrous oxide (70 nmol mol-1 of N2O). This indicates that refractory aerosol originates from the upper stratosphere or the mesosphere. Derived from the mixing ratio of the simultaneously measured long-lived tracer N2O, an empirical index serves to differentiate probed air masses according to their origin: inside the vortex, the vortex edge region, or outside the vortex. Previously observed high fractions of refractory submicron aerosol in the 2003 Arctic vortex were ascribed to unusually strong subsidence during that winter. However, measurements under perturbed vortex conditions in 2010 and during early winter in December 2011 revealed similarly high values. Thus, the abundance of refractory aerosol in the lower stratosphere within the Arctic vortices appears to be a regular feature rather than the exception. During December, the import from aloft into the lower stratosphere appears to be developing; thereafter the abundance of refractory aerosol inside the vortex reaches its highest levels in March. The correlations of refractory aerosol with N2O suggest that, apart from mean subsidence, diabatic dispersion inside the vortex significantly contributes to the transport of particles to the Arctic lower stratosphere. A measurement-based estimate of the total mass of refractory aerosol inside the vortex is provided for each campaign. Based on the derived increase of particle mass in the lower stratospheric vortex (100-67 hPa pressure altitude) by a factor of 4.5 between early and

  14. Controllable generation and manipulation of micro-bubbles in water with absorptive colloid particles by CW laser radiation

    DEFF Research Database (Denmark)

    Angelsky, O. V.; Bekshaev, A. Ya.; Maksimyak, P. P.

    2017-01-01

    Micrometer-sized vapor-gas bubbles are formed due to local heating of a water suspension containing absorptive pigment particles of 100 nm diameter. The heating is performed by CW near-infrared (980 nm) laser radiation with controllable power, focused into a 100 mu m spot within a 2 mm suspension...

  15. Assessment of new-generation high-power electronic nicotine delivery system as thermal aerosol generation device for inhaled bronchodilators.

    Science.gov (United States)

    Pourchez, Jérémie; de Oliveira, Fabien; Perinel-Ragey, Sophie; Basset, Thierry; Vergnon, Jean-Michel; Prévôt, Nathalie

    2017-02-25

    A need remains for alternative devices for aerosol drug delivery that are low cost, convenient and easy to use for the patient, but also capable of producing small-sized aerosol particles. This study investigated the potential of recent high power electronic nicotine delivery systems (ENDS) as aerosol generation devices for inhaled bronchodilators. The particle size distribution was measured using a cascade impactor. The delivery of terbutaline sulfate, a current bronchodilator used for asthma or COPD therapy by inhalation, was studied. This drug was quantified by liquid chromatography coupled with tandem mass spectrometry. The particle size distribution in terms of mass frequency (in two ways, gravimetrically and quantitatively through drug assay on each stage) and the terbutaline sulfate concentration in the aerosol were elucidated. The mass median aerodynamic diameter (MMAD) and the drug delivery rose when the power level increased, to reach 5.6±0.4μg/puff with a MMAD of 0.78±0.03μm at 25W. New generation high-power ENDS are very efficient to generate carrier-droplets in the submicron range containing drug molecules with a constant drug concentration whatever the size-fractions. ENDS appear to be highly patient-adaptive. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Size effects in piezoelectric cantilevers at submicron thickness levels due to flexoelectricity

    Science.gov (United States)

    Moura, Adriane G.; Erturk, Alper

    2017-04-01

    In elastic dielectrics, piezoelectricity is the response of polarization to applied mechanical strain, and vice versa. Piezoelectric coupling is controlled by a third-rank tensor and is allowed only in materials that are non-centrosymmetric. Flexoelectricity, however, is the generation of electric polarization by the application of a non-uniform mechanical strain field, i.e. a strain gradient, and is expected to be pronounced at submicron thickness levels, especially at the nano-scale. Flexoelectricity is controlled by a fourth-rank tensor and is therefore allowed in materials of any symmetry. As a gradient effect, flexoelectricity is size dependent, while piezoelectric coupling has no size dependence. Any ordinary piezoelectric cantilever model developed for devices above micron-level thickness has to be modified for nano-scale piezoelectric devices since the effect of flexoelectric coupling will change the electroelastic dynamics at such small scales. In this work, we establish and explore a complete analytical framework by accounting for both the piezoelectric and flexoelectric effects. The focus is placed on the development of governing electroelastodynamic piezoelectric-flexoelectric equations for the problems of energy harvesting, sensing, and actuation. The coupled governing equations are analyzed to obtain the frequency response. The coupling coefficient for the bimorph configuration is identified and its size dependence is explored.

  17. High energy density supercapacitors from lignin derived submicron activated carbon fibers in aqueous electrolytes

    Science.gov (United States)

    Hu, Sixiao; Zhang, Sanliang; Pan, Ning; Hsieh, You-Lo

    2014-12-01

    Highly porous submicron activated carbon fibers (ACFs) were robustly generated from low sulfonated alkali lignin and fabricated into supercapacitors for capacitive energy storage. The hydrophilic and high specific surface ACFs exhibited large-size nanographites and good electrical conductivity to demonstrate outstanding electrochemical performance. ACFs from KOH activation, in particular, showed very high 344 F g-1 specific capacitance at low 1.8 mg cm-2 mass loading and 10 mV s-1 scan rate in aqueous electrolytes. Even at relatively high scan rate of 50 mV s-1 and mass loading of 10 mg cm-2, a decent specific capacitance of 196 F g-1 and a remarkable areal capacitance of 0.55 F cm-2 was obtained, leading to high energy density of 8.1 Wh kg-1 based on averaged electrodes mass. Furthermore, over 96% capacitance retention rates were achieved after 5000 charge/discharge cycles. Such excellent performance demonstrated great potential of lignin derived carbons for electrical energy storage.

  18. Synthesis and postmodification of functionally relevant organically modified silica particles

    Science.gov (United States)

    Brozek, Eric

    This thesis describes the synthesis and properties of organically modified silica (ORMOSIL) particles with possible applications in the field of drug delivery. Nanoparticle drug delivery methods take advantage of the unique physical properties of nanoscale architecture to deliver a large payload of drug to a targeted site. They are highly porous, contain many organic functionalities for covalent attachment, and their surfaces can be functionalized. A particle-based approach allows for the delivery of a large and localized payload in a single package. Initial study focused on the generation of submicron organically modified silica particles containing boron. This involved the synthesis of vinyl-enriched silica particles and the postmodification of the vinyl functionalities throughout the particle body. Hydroboration and bromination of the vinyl functionalities showed for the first time that the organic functionalities of ORMOSIL particles could be significantly modified. Next, new organically modified silica particle types were developed. These new particle types incorporated unique organic functionalities that may undergo additional functionalization. Organic functionalities included alkenyl-, cyano-, mercapto-, and isocyanto- throughout the particle body. The different organic functionalities were then modified to demonstrate their reactivity. Finally, a particle containing nuclei suitable for neutron capture therapy, a fluorescent tag, and targeting ligand was synthesized. Boron was the active nuclei, fluorescein was the fluorescent label, useful for in vitro studies, and folic acid is a broad field targeting ligand, useful in targeting a variety of cancer types. The particle containing the three unique motifs underwent early stages of in vitro studies against the OVCAR-3 cell line. This thesis has considerably advanced the field of ORMOSIL chemistry through the development and modification of new ORMOSIL products. While initial efforts were geared toward the

  19. Metal-bearing Aerosols of Industrial Origin from Multiple Sources in South Phoenix, Arizona: Separating Similar Particle Types with Minor Element Differences Using Automated SEM Analysis of Large Populations of Particles

    Science.gov (United States)

    Anderson, J.; Hua, X.

    2009-12-01

    Particulate pollution, especially PM10, in the Greater Phoenix (Maricopa County) airshed is a long-standing problem. While much of the PM10 can be ascribed to soil dust entrained by human activity (e.g., sand and gravel mining and other construction-support activities both directly and indirectly), south-central and southwest Phoenix have a significant number of industrial sources of metal-bearing particles. Many of these particles are dominated compositionally by Fe but have minor elements such as Cu, Ba, Mn, Cr, Ni and others which can be statistically mutually exclusive when large populations are looked at with automated Scanning Electron Microscopy (SEM). Bulk aerosol chemical analysis of high-volume samples shows the presence of these elements, including the dominance of Fe at times, but there are far more potential sources than can ever by deduced by principal component analysis of the bulk sample data. Because of the potential toxic nature of these industrial particles, about which there is considerable community concern, identifying the multiple sources is a key step in mitigating the pollution. Also present in these industrial aerosols are mostly submicron particles containing Sr, Sb, V, Cd, and other elements in various combinations. While analyzing the minor element content of submicron particles, some of which are beam-sensitive, pushes the limits of automated SEM techniques, this is the only way to examine large, statistically significant particle populations in many samples on an individual-particle basis. The elemental associations in these unusual metal-bearing particles tend to be the key to source identification. Particle morphology is also important in separating particle types from different sources in these populations. For instance, one of major sources of Fe-dominant particles in southwest Phoenix is a scrap metal operation that uses a “mega-shredder”. This mega-shredder generates enough heat to melt some of the metal and produce roughly

  20. Characterization of near-highway submicron aerosols in New York City with a high-resolution aerosol mass spectrometer

    Directory of Open Access Journals (Sweden)

    Y. L. Sun

    2012-02-01

    Full Text Available Knowledge of the variations of mass concentration, chemical composition and size distributions of submicron aerosols near roadways is of importance for reducing exposure assessment uncertainties in health effects studies. The goal of this study is to deploy and evaluate an Atmospheric Sciences Research Center-Mobile Laboratory (ASRC-ML, equipped with a suite of rapid response instruments for characterization of traffic plumes, adjacent to the Long Island Expressway (LIE – a high-traffic highway in the New York City Metropolitan Area. In total, four measurement periods, two in the morning and two in the evening were conducted at a location approximately 30 m south of the LIE. The mass concentrations and size distributions of non-refractory submicron aerosol (NR-PM1 species were measured in situ at a time resolution of 1 min by an Aerodyne High-Resolution Time-of-Flight Aerosol Mass Spectrometer, along with rapid measurements (down to 1 Hz of gaseous pollutants (e.g. HCHO, NO2, NO, O3, and CO2, etc., black carbon (BC, and particle number concentrations and size distributions. Particulate organics varied dramatically during periods with high traffic influences from the nearby roadway. The variations were mainly observed in the hydrocarbon-like organic aerosol (HOA, a surrogate for primary OA from vehicle emissions. The inorganic species (sulfate, ammonium, and nitrate and oxygenated OA (OOA showed much smoother variations indicating minor impacts from traffic emissions. The concentration and chemical composition of NR-PM1 also varied differently on different days depending on meteorology, traffic intensity and vehicle types. Overall, organics dominated the traffic-related NR-PM1 composition (>60% with HOA accounting for a major fraction of OA. The traffic-influenced organics showed two distinct modes in mass-weighted size distributions, peaking at ∼120 nm and 500 nm (vacuum

  1. Computational fluid dynamics and particle image velocimetry assisted design tools for a new generation of trochoidal gear pumps

    Directory of Open Access Journals (Sweden)

    M Garcia-Vilchez

    2015-06-01

    Full Text Available Trochoidal gear pumps produce significant flow pulsations that result in pressure pulsations, which interact with the system where they are connected, shortening the life of both the pump and circuit components. The complicated aspects of the operation of a gerotor pump make computational fluid dynamics the proper tool for modelling and simulating its flow characteristics. A three-dimensional model with deforming mesh computational fluid dynamics is presented, including the effects of the manufacturing tolerance and the leakage inside the pump. A new boundary condition is created for the simulation of the solid contact in the interteeth radial clearance. The experimental study of the pump is carried out by means of time-resolved particle image velocimetry, and results are qualitatively evaluated, thanks to the numerical simulation results. Time-resolved particle image velocimetry is developed in order to adapt it to the gerotor pump, and it is proved to be a feasible alternative to obtain the instantaneous flow of the pump in a direct mode, which would allow the determination of geometries that minimize the non-desired flow pulsations. Thus, a new methodology involving computational fluid dynamics and time-resolved particle image velocimetry is presented, which allows the obtaining of the instantaneous flow of the pump in a direct mode without altering its behaviour significantly.

  2. Cloud condensation nucleus (CCN behavior of organic aerosol particles generated by atomization of water and methanol solutions

    Directory of Open Access Journals (Sweden)

    T. A. Rissman

    2007-06-01

    Full Text Available Cloud condensation nucleus (CCN experiments were carried out for malonic acid, succinic acid, oxalacetic acid, DL-malic acid, glutaric acid, DL-glutamic acid monohydrate, and adipic acid, using both water and methanol as atomization solvents, at three operating supersaturations (0.11%, 0.21%, and 0.32% in the Caltech three-column CCN instrument (CCNC3. Predictions of CCN behavior for five of these compounds were made using the Aerosol Diameter Dependent Equilibrium Model (ADDEM. The experiments presented here expose important considerations associated with the laboratory measurement of the CCN behavior of organic compounds. Choice of atomization solvent results in significant differences in CCN activation for some of the compounds studied, which could result from residual solvent, particle morphology differences, and chemical reactions between the particle and gas phases. Also, significant changes in aerosol size distribution occurred after classification in a differential mobility analyzer (DMA for malonic acid and glutaric acid, preventing confident interpretation of experimental data for these two compounds. Filter analysis of adipic acid atomized from methanol solution indicates that gas-particle phase reactions may have taken place after atomization and before methanol was removed from the sample gas stream. Careful consideration of these experimental issues is necessary for successful design and interpretation of laboratory CCN measurements.

  3. Optimal reactive power and voltage control in distribution networks with distributed generators by fuzzy adaptive hybrid particle swarm optimisation method

    DEFF Research Database (Denmark)

    Chen, Shuheng; Hu, Weihao; Su, Chi

    2015-01-01

    A new and efficient methodology for optimal reactive power and voltage control of distribution networks with distributed generators based on fuzzy adaptive hybrid PSO (FAHPSO) is proposed. The objective is to minimize comprehensive cost, consisting of power loss and operation cost of transformers...... that the proposed method can search a more promising control schedule of all transformers, all capacitors and all distributed generators with less time consumption, compared with other listed artificial intelligent methods....

  4. Fabrication of high aspect ratio submicron gratings on ˜100nm titanium membranes using electron beam lithography

    Science.gov (United States)

    Tiwari, Pragya; Mondal, Puspen; Srivastava, A. K.; Naik, P. A.

    2017-05-01

    We have developed a new technique for fabrication of 1:1 submicron gratings by means of single step electron beam lithography coupled with thin film deposition. The edge profile and the width ratio (line-to-groove) are easily controlled. Metal like gold or copper transmission gratings can be produced by an additional lift-off process. A 30kV electron beam was used to generate 500nm lines on standalone ˜2.3μm thick PMMA/Titanium. The dimensions of fabricated features together with their surface morphology and profiles were investigated by optical microscope and SEM. Low current slow writing coupled with special development is optimized to write structures smaller than the thickness of the resist membrane.

  5. A statistical analysis of North East Atlantic (submicron aerosol size distributions

    Directory of Open Access Journals (Sweden)

    M. Dall'Osto

    2011-12-01

    Full Text Available The Global Atmospheric Watch research station at Mace Head (Ireland offers the possibility to sample some of the cleanest air masses being imported into Europe as well as some of the most polluted being exported out of Europe. We present a statistical cluster analysis of the physical characteristics of aerosol size distributions in air ranging from the cleanest to the most polluted for the year 2008. Data coverage achieved was 75% throughout the year. By applying the Hartigan-Wong k-Means method, 12 clusters were identified as systematically occurring. These 12 clusters could be further combined into 4 categories with similar characteristics, namely: coastal nucleation category (occurring 21.3 % of the time, open ocean nucleation category (occurring 32.6% of the time, background clean marine category (occurring 26.1% of the time and anthropogenic category (occurring 20% of the time aerosol size distributions. The coastal nucleation category is characterised by a clear and dominant nucleation mode at sizes less than 10 nm while the open ocean nucleation category is characterised by a dominant Aitken mode between 15 nm and 50 nm. The background clean marine aerosol exhibited a clear bimodality in the sub-micron size distribution, with although it should be noted that either the Aitken mode or the accumulation mode may dominate the number concentration. However, peculiar background clean marine size distributions with coarser accumulation modes are also observed during winter months. By contrast, the continentally-influenced size distributions are generally more monomodal (accumulation, albeit with traces of bimodality. The open ocean category occurs more often during May, June and July, corresponding with the North East (NE Atlantic high biological period. Combined with the relatively high percentage frequency of occurrence (32.6%, this suggests that the marine biota is an important source of new nano aerosol particles in NE Atlantic Air.

  6. Relative contribution of submicron and supermicron particles to aerosol light scattering in the marine boundary layer

    NARCIS (Netherlands)

    Kleefeld, C.; O'Dowd, C.D.; O'Reilly, S.; Jennings, S.G.; Aalto, P.; Becker, E.; Kunz, G.J.; Leeuw, G. de

    2002-01-01

    Measurements of the aerosol light scattering coefficient (σsp) at a wavelength of λ - 550 nm were conducted at a coastal atmospheric research station in the east Atlantic Ocean during June 1999. Size distribution measurements between diameters of 3 nm and 40 um (at ambient humidity) were used to

  7. Characterization of submicron particles during biomass burning and coal combustion periods in Beijing, China.

    Science.gov (United States)

    Zhang, J K; Cheng, M T; Ji, D S; Liu, Z R; Hu, B; Sun, Y; Wang, Y S

    2016-08-15

    An Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS) was deployed along with other observation instruments to measure the characteristics of PM1 (particulate matter with a vacuum aerodynamic diameter of ≤1μm) during the biomass burning period (October 1 to 27; BBP) and the coal combustion period (December 10 to 31; CCP) in Beijing in 2014. The average PM1 mass concentrations during the BBP and CCP were 82.3 and 37.5μgm(-3), respectively. Nitrate, ammonium and other pollutants emitted by the burning processes, especially coal combustion, increased significantly in association with increased pollution levels. Positive matrix factorization (PMF) was applied to a unified high-resolution mass spectra database of organic species with NO(+) and NO2(+) ions to discover the relationships between organic and inorganic species. One inorganic factor was identified in both periods, and another five and four distinct organic factors were identified in the BBP and CCP, respectively. Secondary organic aerosols (SOAs) accounted for 55% of the total organic aerosols (OAs) during the BBP, which is higher than the proportion during the CCP (oxygenated OA, 40%). The organic nitrate and inorganic nitrate were first successfully separated through the PMF analysis based on the HR-ToF-AMS observations in Beijing, and organic nitrate components accounted for 21% and 18% of the total nitrate mass during the BBP and CCP, respectively. Although the PM1 mass concentration during the CCP was much lower than in the BBP, the average concentration of polycyclic aromatic hydrocarbons (PAHs) during the CCP (107.3±171.6ngm(-3)) was ~5 times higher than that in the BBP (21.9±21.7ngm(-3)). Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Quantification of the carbonaceous matter origin in submicron marine aerosol particles by dual carbon isotope analysis

    OpenAIRE

    D. Ceburnis; A. Garbaras; S. Szidat; M. Rinaldi; S. Fahrni; N. Perron; L. Wacker; S. Leinert; V. Remeikis; M. C. Facchini; A. S. H. Prevot; S. G. Jennings; C. D. O'Dowd

    2011-01-01

    Dual carbon isotope analysis has been performed for the first time demonstrating a potential in organic matter apportionment between three principal sources: marine, terrestrial (non-fossil) and fossil fuel due to unique isotopic signatures. The results presented here, utilising combinations of dual carbon isotope analysis, provides a conclusive evidence of a dominant biogenic organic fraction to organic aerosol over biologically active oceans. In particular, the NE Atlantic, which is...

  9. Study of Submicron Particle Size Distributions by Laser Doppler Measurement of Brownian Motion.

    Science.gov (United States)

    1984-10-29

    acquisition and recording apparatus; and c) Development of appropriate software for analysis of signals obtained from the Brownian motion instrument...time scales (e.g., the transit time of the A-17 .- -. . , " 2.0 19 _j 1.2 08 0.6 0.4 0.2 0.0 0 500 1000 1500 2000 TIPOE STEP (10 ns/step) 2.0 1.8

  10. Dynamics of Dissolved Organic Matter and Microbes in Seawater through Sub-Micron Particle Size Analyses

    Digital Repository Service at National Institute of Oceanography (India)

    Goes, J.I.; Balch, W.M.; Vaughn, J.M.; Gomes, H.R.

    processes responsible for the dynamics of DOM rely on monitoring the consumption and breakdown of specific compounds of phytoplankton origin, generally, through the use of labeled precursors and substrates (Kirchman et al., 1991; Fry et al., 1996; Rich et al... attempts to determine the molecular weight or size spectrum of DOM using size exclusion chromatography, but these have generally proven unsatisfactory (Beckett et al., 1987). One reason is that DOM is exposed to high shear stresses during separation...

  11. Ozone and Limonene in Indoor Air: A Source of Submicron Particle Exposure

    National Research Council Canada - National Science Library

    Thomas Wainman; Junfeng Zhang; Charles J. Weschler; Paul J. Lioy

    2000-01-01

    .... We conducted a series of experiments to investigate the potential for secondary aerosol in indoor air as a result of the reaction of ozone with d-limonene, a compound commonly used in air fresheners...

  12. Field Assessment of Enclosed Cab Filtration System Performance Using Particle Counting Measurements

    Science.gov (United States)

    Organiscak, John A.; Cecala, Andrew B.; Noll, James D.

    2015-01-01

    Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners’ exposure to airborne dust generated during mining operations. The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently worked with a mining equipment manufacturer to examine a new cab filtration system design for underground industrial minerals equipment. This cab filtration system uses a combination of three particulate filters to reduce equipment operators’ exposure to dust and diesel particulates present in underground industrial mineral mines. NIOSH initially examined this cab filtration system using a two-instrument particle counting method at the equipment company’s manufacturing shop facility to assess several alternative filters. This cab filtration system design was further studied on several pieces of equipment during a two- to seven-month period at two underground limestone mines. The two-instrument particle counting method was used outside the underground mine at the end of the production shifts to regularly test the cabs’ long-term protection factor performance with particulates present in the ambient air. This particle counting method showed that three of the four cabs achieved protection factors greater than 1,000 during the field studies. The fourth cab did not perform at this level because it had a damaged filter in the system. The particle counting measurements of submicron particles present in the ambient air were shown to be a timely and useful quantification method in assessing cab performance during these field studies. PMID:23915268

  13. Field assessment of enclosed cab filtration system performance using particle counting measurements.

    Science.gov (United States)

    Organiscak, John A; Cecala, Andrew B; Noll, James D

    2013-01-01

    Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners' exposure to airborne dust generated during mining operations. The National Institute for Occupational Safety and Health (NIOSH) Office of Mine Safety and Health Research (OMSHR) has recently worked with a mining equipment manufacturer to examine a new cab filtration system design for underground industrial minerals equipment. This cab filtration system uses a combination of three particulate filters to reduce equipment operators' exposure to dust and diesel particulates present in underground industrial mineral mines. NIOSH initially examined this cab filtration system using a two-instrument particle counting method at the equipment company's manufacturing shop facility to assess several alternative filters. This cab filtration system design was further studied on several pieces of equipment during a two- to seven-month period at two underground limestone mines. The two-instrument particle counting method was used outside the underground mine at the end of the production shifts to regularly test the cabs' long-term protection factor performance with particulates present in the ambient air. This particle counting method showed that three of the four cabs achieved protection factors greater than 1,000 during the field studies. The fourth cab did not perform at this level because it had a damaged filter in the system. The particle counting measurements of submicron particles present in the ambient air were shown to be a timely and useful quantification method in assessing cab performance during these field studies.

  14. High-power radio frequency pulse generation and extration based on wakefield excited by an intense charged particle beam in dielectric-loaded waveguides.

    Energy Technology Data Exchange (ETDEWEB)

    Gao, F.; High Energy Physics; Illinois Inst. of Tech

    2009-07-24

    Power extraction using a dielectric-loaded (DL) waveguide is a way to generate high-power radio frequency (RF) waves for future particle accelerators, especially for two-beam-acceleration. In a two-beam-acceleration scheme, a low-energy, high-current particle beam is passed through a deceleration section of waveguide (decelerator), where the power from the beam is partially transferred to trailing electromagnetic waves (wakefields); then with a properly designed RF output coupler, the power generated in the decelerator is extracted to an output waveguide, where finally the power can be transmitted and used to accelerate another usually high-energy low-current beam. The decelerator, together with the RF output coupler, is called a power extractor. At Argonne Wakefield Accelerator (AWA), we designed a 7.8GHz power extractor with a circular DL waveguide and tested it with single electron bunches and bunch trains. The output RF frequency (7.8GHz) is the sixth harmonic of the operational frequency (1.3GHz) of the electron gun and the linac at AWA. In single bunch excitation, a 1.7ns RF pulse with 30MW of power was generated by a single 66nC electron bunch passing through the decelerator. In subsequent experiments, by employing different splitting-recombining optics for the photoinjector laser, electron bunch trains were generated and thus longer RF pulses could be successfully generated and extracted. In 16-bunch experiments, 10ns and 22ns RF pulses have been generated and extracted; and in 4-bunch experiments, the maximum power generated was 44MW with 40MW extracted. A 26GHz DL power extractor has also been designed to test this technique in the millimeter-wave range. A power level of 148MW is expected to be generated by a bunch train with a bunch spacing of 769ps and bunch charges of 20nC each. The arrangement for the experiment is illustrated in a diagram. Higher-order-mode (HOM) power extraction has also been explored in a dual-frequency design. By using a bunch

  15. Hybrid Particle Swarm Optimization based Day-Ahead Self-Scheduling for Thermal Generator in Competitive Electricity Market

    DEFF Research Database (Denmark)

    Pindoriya, Naran M.; Singh, S.N.; Østergaard, Jacob

    2009-01-01

    integer nonlinear programming. To demonstrate the effectiveness of the proposed method for self-scheduling in a day-ahead energy market, the locational margin price (LMP) forecast uncertainty in PJM electricity market is considered. An adaptive wavelet neural network (AWNN) is used to forecast the day...... in day-ahead energy market subject to operational constraints and 2) at the same time, to minimize the risk due to uncertainty in price forecast. Therefore, it is a conflicting bi-objective optimization problem which has both binary and continuous optimization variables considered as constrained mixed......This paper presents a hybrid particle swarm optimization algorithm (HPSO) to solve the day-ahead self-scheduling for thermal power producer in competitive electricity market. The objective functions considered to model the self-scheduling problem are 1) to maximize the profit from selling energy...

  16. Peculiarities of secondary particle generation process in Pb-Pb interactions at 158 A GeV

    CERN Document Server

    Astafyeva, N M; Dremin, I M; Feinberg, E L; Goncharova, L A; Kotelnikov, K A; Martynov, A G; Polukhina, N G

    1997-01-01

    Experimental data on Pb-Pb central collisions were obtained by means of emulsion magnetic chambers containing the lead target irradiated with the Pb beam in the magnetic field of 1.8 Tesla at CERN in December, 1994 and November, 1995. 50 mu m thick emulsion layers were placed perpendicular to the beam. Results of data analysis show existence of certain peculiar patterns in several central collisions (e.g. ring-like events, jets, multiple narrow spikes in secondary particle pseudorapidity distributions, etc.). The methods of pattern recognition theory, in particular, wavelet technique (the method of localized spectral analysis), used in target diagram analysis, reveal the detailed features of such structures. (9 refs).

  17. Characterization and source apportionment of submicron aerosol with aerosol mass spectrometer during the PRIDE-PRD 2006 campaign

    Directory of Open Access Journals (Sweden)

    R. Xiao

    2011-07-01

    Full Text Available Size-resolved chemical compositions of non-refractory submicron aerosol were measured using an Aerodyne quadrupole aerosol mass spectrometer (Q-AMS at the rural site Back Garden (BG, located ~50 km northwest of Guangzhou in July 2006. This paper characterized the submicron aerosol particles of regional air pollution in Pearl River Delta (PRD in the southern China. Organics and sulfate dominated the submicron aerosol compositions, with average mass concentrations of 11.8 ± 8.4 μg m−3 and 13.5 ± 8.7 μg m−3, respectively. Unlike other air masses, the air masses originated from Southeast-South and passing through the PRD urban areas exhibited distinct bimodal size distribution characteristics for both organics and sulfate: the first mode peaked at vacuum aerodynamic diameters (Dva ∼200 nm and the second mode occurred at Dva from 300–700 nm. With the information from AMS, it was found from this study that the first mode of organics in PRD regional air masses was contributed by both secondary organic aerosol formation and combustion-related emissions, which is different from most findings in other urban areas (first mode of organics primarily from combustion-related emissions. The analysis of AMS mass spectra data by positive matrix factorization (PMF model identified three sources of submicron organic aerosol including hydrocarbon-like organic aerosol (HOA, low volatility oxygenated organic aerosol (LV-OOA and semi-volatile oxygenated organic aerosol (SV-OOA. The strong correlation between HOA and EC indicated primary combustion emissions as the major source of HOA while a close correlation between SV-OOA and semi-volatile secondary species nitrate as well as between LV-OOA and nonvolatile secondary species sulfate suggested secondary aerosol formation as the major source of SV-OOA and LV-OOA at the BG site. However, LV-OOA was more aged than SV-OOA as its spectra was highly

  18. Characterization and source apportionment of submicron aerosol with aerosol mass spectrometer during the PRIDE-PRD 2006 campaign

    Science.gov (United States)

    Xiao, R.; Takegawa, N.; Zheng, M.; Kondo, Y.; Miyazaki, Y.; Miyakawa, T.; Hu, M.; Shao, M.; Zeng, L.; Gong, Y.; Lu, K.; Deng, Z.; Zhao, Y.; Zhang, Y. H.

    2011-07-01

    Size-resolved chemical compositions of non-refractory submicron aerosol were measured using an Aerodyne quadrupole aerosol mass spectrometer (Q-AMS) at the rural site Back Garden (BG), located ~50 km northwest of Guangzhou in July 2006. This paper characterized the submicron aerosol particles of regional air pollution in Pearl River Delta (PRD) in the southern China. Organics and sulfate dominated the submicron aerosol compositions, with average mass concentrations of 11.8 ± 8.4 μg m-3 and 13.5 ± 8.7 μg m-3, respectively. Unlike other air masses, the air masses originated from Southeast-South and passing through the PRD urban areas exhibited distinct bimodal size distribution characteristics for both organics and sulfate: the first mode peaked at vacuum aerodynamic diameters (Dva) ∼200 nm and the second mode occurred at Dva from 300-700 nm. With the information from AMS, it was found from this study that the first mode of organics in PRD regional air masses was contributed by both secondary organic aerosol formation and combustion-related emissions, which is different from most findings in other urban areas (first mode of organics primarily from combustion-related emissions). The analysis of AMS mass spectra data by positive matrix factorization (PMF) model identified three sources of submicron organic aerosol including hydrocarbon-like organic aerosol (HOA), low volatility oxygenated organic aerosol (LV-OOA) and semi-volatile oxygenated organic aerosol (SV-OOA). The strong correlation between HOA and EC indicated primary combustion emissions as the major source of HOA while a close correlation between SV-OOA and semi-volatile secondary species nitrate as well as between LV-OOA and nonvolatile secondary species sulfate suggested secondary aerosol formation as the major source of SV-OOA and LV-OOA at the BG site. However, LV-OOA was more aged than SV-OOA as its spectra was highly correlated with the reference spectra of fulvic acid, an indicator of aged and

  19. Fabrication and characterization of submicron polymer waveguides by micro-transfer molding

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Te-Wei [Iowa State Univ., Ames, IA (United States)

    2009-01-01

    Various methods exist for fabrication of micron and submicron sized waveguide structures. However, most of them include expensive and time consuming semiconductor fabrication techniques. An economical method for fabricating waveguide structures is introduced and demonstrated in this thesis. This method is established based on previously well-developed photonic crystal fabrication method called two-polymer microtransfer molding. The waveguide in this work functions by a coupler structure that diffracts the incident light into submicron polymer rods. The light is then guided through the rods. Characterization is done by collecting the light that has been guided through the waveguide and exits the end of these submicron polymer bars. The coupling and waveguiding capabilities are demonstrated using two light sources, a laser and white light.

  20. Size fractionation and characterisation of fresh water colloids and particles: split-flow thin-cell and electron microscopy analyses.

    Science.gov (United States)

    De Momi, Anna; Lead, Jamie R

    2006-11-01

    Split-flow thin-cell (SPLITT) was employed in conventional mode (CSF), to size-fractionate colloids and particles from a selected freshwater. Imaging and quantification by calculations of particle size distributions (PSDs) and shape factors were performed on sample analyzed by conventional high vacuum scanning electron microscopy (SEM) and environmental SEM (ESEM), to investigate the ability of SPLITT to make accurate and nonperturbing separations. SEM and ESEM images of unperturbed and SPLITT-generated fractions were used in order to obtain qualitative and quantitative information about the properties of colloids and particles. Particle size distributions (PSDs) showed that separations were very good, agreeing with theoretical behavior. ESEM PSDs showed that up to 87-88% of the material in the a fraction (expected to be 1 microm) 87-95% of the material was the expected size. The SEM data indicated a slightly higher contamination of the b fraction with the presence of submicron colloids. Moreover, analysis of conformations indicated significant nonsphericity in unfractionated colloids and particles, but after SPLITT fractionation, shape factors showed that particles were significantly more spherical than before separation.

  1. Sum-frequency generation spectroscopy on metals, oxides, and oxide-supported metal particles; Summenfrequenzerzeugungsspektroskopie an Metallen, Oxiden und oxidgetraegerten Metallpartikeln

    Energy Technology Data Exchange (ETDEWEB)

    Aumer, Andreas

    2010-06-21

    This thesis focuses on 4 different model systems of surface science. The experimental techniques used for the measurements include sum frequency generation (SFG), thermal desorption spectroscopy (TDS), low energy electron diffraction (LEED), Auger electron spectroscopy (AES), infrared adsorption spectrosocopy (IRAS) and scanning tunneling microscopy (STM). By using SFG, measurements could be performed up to a pressure of 50 mbar. The systems under investigation were: CO on Pt(111), water on Ag(001) and on MgO/Ag(001), CO on Au/MgO/Ag(001), and CO on Au-Pd/MgO/Ag(001). The system of CO on Pt(111) exhibits a two peak-pattern under certain pressure and temperature conditions which has not been studied so far. Various experiments helped to elucidate the origin of this distinct behaviour. The measurements of water on Ag(001) and MgO/Ag(001) show that on MgO, water first adsorbs as a monolayer with a following multilayer, whereas on Ag(001) it adsorbs as a multilayer from the beginning. The monolayer can be studied below the multilayer and some resonances can be identified. For the case of Au/MgO/Ag(001), STM shows that the growth mode of Au depends on the thickness of the supporting MgO film, which can not be seen with spectroscopic methods. For mixed Au-Pd particles on MgO/Ag(001) a clear difference in the adsorption behaviour between pure metal particles and mixed particles can be seen, which is explained by an interaction between these metals. Annealing the mixed particles to 600 K leads to a segregation of the metals, where the Au atoms diffuse to the shell and the Pd atoms make up the core. The results of all these measurements are discussed in the light of recent publications. (orig.)

  2. Pseudospectral Maxwell solvers for an accurate modeling of Doppler harmonic generation on plasma mirrors with particle-in-cell codes

    Science.gov (United States)

    Blaclard, G.; Vincenti, H.; Lehe, R.; Vay, J. L.

    2017-09-01

    With the advent of petawatt class lasers, the very large laser intensities attainable on target should enable the production of intense high-order Doppler harmonics from relativistic laser-plasma mirror interactions. At present, the modeling of these harmonics with particle-in-cell (PIC) codes is extremely challenging as it implies an accurate description of tens to hundreds of harmonic orders on a broad range of angles. In particular, we show here that due to the numerical dispersion of waves they induce in vacuum, standard finite difference time domain (FDTD) Maxwell solvers employed in most PIC codes can induce a spurious angular deviation of harmonic beams potentially degrading simulation results. This effect was extensively studied and a simple toy model based on the Snell-Descartes law was developed that allows us to finely predict the angular deviation of harmonics depending on the spatiotemporal resolution and the Maxwell solver used in the simulations. Our model demonstrates that the mitigation of this numerical artifact with FDTD solvers mandates very high spatiotemporal resolution preventing realistic three-dimensional (3D) simulations even on the largest computers available at the time of writing. We finally show that nondispersive pseudospectral analytical time domain solvers can considerably reduce the spatiotemporal resolution required to mitigate this spurious deviation and should enable in the near future 3D accurate modeling on supercomputers in a realistic time to solution.

  3. Influences of Substrate Adhesion and Particle Size on the Shape Memory Effect of Polystyrene Particles.

    Science.gov (United States)

    Cox, Lewis M; Killgore, Jason P; Li, Zhengwei; Long, Rong; Sanders, Aric W; Xiao, Jianliang; Ding, Yifu

    2016-04-19

    Formulations and applications of micro- and nanoscale polymer particles have proliferated rapidly in recent years, yet knowledge of their mechanical behavior has not grown accordingly. In this study, we examine the ways that compressive strain, substrate surface energy, and particle size influence the shape memory cycle of polystyrene particles. Using nanoimprint lithography, differently sized particles are programmed into highly deformed, temporary shapes in contact with substrates of differing surface energies. Atomic force microscopy is used to obtain in situ measurements of particle shape recovery kinetics, and scanning electron microscopy is employed to assess differences in the profiles of particles at the conclusion of the shape memory cycle. Finally, finite element models are used to investigate the growing impact of surface energies at smaller length scales. Results reveal that the influence of substrate adhesion on particle recovery is size-dependent and can become dominating at submicron length scales.

  4. Generation of porcine reproductive and respiratory syndrome (PRRS) virus-like-particles (VLPs) with different protein composition.

    Science.gov (United States)

    García Durán, Marga; Costa, Sofia; Sarraseca, Javier; de la Roja, Nuria; García, Julia; García, Isabel; Rodríguez, Maria José

    2016-10-01

    The causative agent of Porcine Reproductive and Respiratory Syndrome (PRRS) is an enveloped ssRNA (+) virus belonging to the Arteriviridae family. Gp5 and M proteins form disulfide-linked heterodimers that constitute the major components of PRRSV envelope. Gp2, Gp3, Gp4 and E are the minor structural proteins, being the first three incorporated as multimeric complexes in the virus surface. The disease has become one of the most important causes of economic losses in the swine industry. Despite efforts to design an effective vaccine, the available ones allow only partial protection. In the last years, VLPs have become good vaccine alternatives because of safety issues and their potential to activate both branches of the immunological response. The characteristics of recombinant baculoviruses as heterologous expression system have been exploited for the production of VLPs of a wide variety of viruses. In this work, two multiple baculovirus expression vectors (BEVs) with PRRS virus envelope proteins were engineered in order to generate PRRS VLPs: on the one hand, Gp5 and M cDNAs were cloned to generate the pBAC-Gp5M vector; on the other hand, Gp2, Gp3, Gp4 and E cDNAs have been cloned to generate the pBAC-Gp234E vector. The corresponding recombinant baculoviruses BAC-Gp5M and BAC-Gp234E were employed to produce two types of VLPs: basic Gp5M VLPs, by the simultaneous expression of Gp5 and M proteins; and complete VLPs, by the co-expression of the six PRRS proteins after co-infection. The characterization of VLPs by Western blot confirmed the presence of the recombinant proteins using the available specific antibodies (Abs). The analysis by Electron microscopy showed that the two types of VLPs were indistinguishable between them, being similar in shape and size to the native PRRS virus. This system represents a potential alternative for vaccine development and a useful tool to study the implication of specific PRRS proteins in the response against the virus. Copyright

  5. Numerical studies of petawatt laser-driven proton generation from two-species targets using a two-dimensional particle-in-cell code

    Science.gov (United States)

    Domański, J.; Badziak, J.; Jabloński, S.

    2016-04-01

    Laser-driven generation of high-energy ion beams has recently attracted considerable interest due to a variety of potential applications including proton radiography, ICF fast ignition, nuclear physics or hadron therapy. The ion beam parameters depend on both laser pulse and target parameters, and in order to produce the ion beam of properties required for a particular application the laser and target parameters must be carefully selected, and the mechanism of the ion beam generation should be well understood and controlled. Convenient and commonly used tools for studies of the ion acceleration process are particle-in-cell (PIC) codes. Using two-dimensional PIC simulations, the properties of a proton beam generated from a thin erbium hydride (ErH3) target irradiated by a 25fs laser pulse of linear or circular polarization and of intensity ranging from 1020 to 1021 W/cm2 are investigated and compared with the features of a proton beam produced from a hydrocarbon (CH) target. It has been found that using erbium hydride targets instead of hydrocarbon ones creates an opportunity to generate more compact proton beams of higher mean energy, intensity and of better collimation. This is especially true for the linear polarization of the laser beam, for which the mean proton energy, the amount of high energy protons and the intensity of the proton beam generated from the hydride target is by an order of magnitude higher than for the hydrocarbon target. For the circular polarization, the proton beam parameters are lower than those for the linear one, and the effect of target composition on the acceleration process is weaker.

  6. Airborne measurements of submicron aerosols across the coastline ...

    Indian Academy of Sciences (India)

    track in the east–west direction extended partly over land and partly over ocean. 2. Instrumentation. A Scanning Mobility Particle Sizer (SMPS), Model. 3080, of TSI, installed onboard a beachcraft air- craft is used to make measurements of the number concentration and size distribution of aerosol par- ticles in the size range ...

  7. Analytical reconstruction scheme for the coarse-mesh solution generated by the spectral nodal method for neutral particle discrete ordinates transport model in slab geometry

    Energy Technology Data Exchange (ETDEWEB)

    Barros, Ricardo C., E-mail: rcbarros@pq.cnpq.b [Programa de Pos-graduacao em Modelagem Computacional, Instituto Politecnico (IPRJ/UERJ), Rua Alberto Rangel s/n, 28630-050 Nova Friburgo, RJ (Brazil); Filho, Hermes Alves, E-mail: halves@iprj.uerj.b [Programa de Pos-graduacao em Modelagem Computacional, Instituto Politecnico (IPRJ/UERJ), Rua Alberto Rangel s/n, 28630-050 Nova Friburgo, RJ (Brazil); Platt, Gustavo M., E-mail: gmplatt@iprj.uerj.b [Programa de Pos-graduacao em Modelagem Computacional, Instituto Politecnico (IPRJ/UERJ), Rua Alberto Rangel s/n, 28630-050 Nova Friburgo, RJ (Brazil); Oliveira, Francisco Bruno S., E-mail: fbrunoso@uol.com.b [Programa de Pos-graduacao em Modelagem Computacional, Instituto Politecnico (IPRJ/UERJ), Rua Alberto Rangel s/n, 28630-050 Nova Friburgo, RJ (Brazil); Militao, Damiano S., E-mail: mestredam@yahoo.com.b [Programa de Pos-graduacao em Modelagem Computacional, Instituto Politecnico (IPRJ/UERJ), Rua Alberto Rangel s/n, 28630-050 Nova Friburgo, RJ (Brazil)

    2010-11-15

    Coarse-mesh numerical methods are very efficient in the sense that they generate accurate results in short computational time, as the number of floating point operations generally decrease, as a result of the reduced number of mesh points. On the other hand, they generate numerical solutions that do not give detailed information on the problem solution profile, as the grid points can be located considerably away from each other. In this paper we describe two steps for the analytical reconstruction of the coarse-mesh solution generated by the spectral nodal method for neutral particle discrete ordinates (S{sub N}) transport model in slab geometry. The first step of the algorithm is based on the analytical reconstruction of the coarse-mesh solution within each discretization cell of the grid set up on the spatial domain. The second step is based on the angular reconstruction of the discrete ordinates solution between two contiguous ordinates of the angular quadrature set used in the S{sub N} model. Numerical results are given so we can illustrate the accuracy of the two reconstruction techniques, as described in this paper.

  8. Photo-induced exciton generation in polyvinylpyrrolidone encapsulated Ag2S core-shells: Electrochemical deposition, regular shape and high order of particle size distribution

    Science.gov (United States)

    Mukherjee, Nillohit; Jana, Sumanta; Gopal Khan, Gobinda; Mondal, Anup

    2012-12-01

    Visible light induced frequency switching behavior, exhibited by the electrochemically deposited thin films of polyvinylpyrrolidone (PVP) encapsulated Ag2S nanosphere (core-shell) is shown here. A low frequency (˜40 Hz) pulse was found to be generated upon illumination with 1 Sun due to excitonic transition, which also showed good switching behavior with the "on" and "off" state of the light. Capping of the semiconductor surface by a polymer like PVP reduces the surface states and thus lowers the built in barrier height and the width of depletion region. So, the number of photo generated but non recombining electron-hole pairs (excitons) increases, which put their signature in some unique physical properties like increase in photoluminescence (PL) intensity, light induced frequency switching behavior due to free exciton generation, etc. Here, the depositions were carried out on indium tin oxide coated glass substrates from an aqueous solution of AgNO3, thioacetamide, and PVP. The films were structurally characterized using high resolution X-ray diffraction, field emission scanning electron microscopy, and high resolution transmission electron microscopic techniques. The deposited particles were regular in shape with significantly high order of size distribution. Furrier transform infrared spectroscopy confirmed the presence of PVP as the encapsulating agent. Optical characterization, viz., UV - vis - NIR and NIR-PL revealed noteworthy amount of NIR emission from the deposited material.

  9. Generation and characterization of a trackable plant-made influenza H5 virus-like particle (VLP) containing enhanced green fluorescent protein (eGFP).

    Science.gov (United States)

    Young, Katie R; Arthus-Cartier, Guillaume; Yam, Karen K; Lavoie, Pierre-Olivier; Landry, Nathalie; D'Aoust, Marc-André; Vézina, Louis-Philippe; Couture, Manon M-J; Ward, Brian J

    2015-09-01

    Medicago, Inc. has developed an efficient virus-like particle (VLP) vaccine production platform using the Nicotiana benthamiana expression system, and currently has influenza-based products targeting seasonal/pandemic hemagglutinin (HA) proteins in advanced clinical trials. We wished to generate a trackable HA-based VLP that would allow us to study both particle assembly in plants and VLP interactions within the mammalian immune system. To this end, a fusion protein was designed, composed of H5 (from influenza A/Indonesia/05/2005 [H5N1]) with enhanced green fluorescent protein (eGFP). Expression of H5-eGFP in N. benthamiana produced brightly fluorescent ∼160 nm particles resembling H5-VLPs. H5-eGFP-VLPs elicited anti-H5 serologic responses in mice comparable to those elicited by H5-VLPs in almost all assays tested (hemagglutination inhibition/IgG(total)/IgG1/IgG2b/IgG2a:IgG1 ratio), as well as a superior anti-GFP IgG response (mean optical density = 2.52 ± 0.16 sem) to that elicited by soluble GFP (mean optical density = 0.12 ± 0.06 sem). Confocal imaging of N. benthamiana cells expressing H5-eGFP displayed large fluorescent accumulations at the cell periphery, and draining lymph nodes from mice given H5-eGFP-VLPs via footpad injection demonstrated bright fluorescence shortly after administration (10 min), providing proof of concept that the H5-eGFP-protein/VLPs could be used to monitor both VLP assembly and immune trafficking. Given these findings, this novel fluorescent reagent will be a powerful tool to gain further fundamental insight into the biology of influenza VLP vaccines. © FASEB.

  10. Analysis and Design of Monolithic Inductors in Sub-micron CMOS

    DEFF Research Database (Denmark)

    Fallesen, Carsten; Jørgensen, Allan

    1997-01-01

    In the last few years the CMOS processes have gone into deep sub-micron channel lengths. This means that it is now possible to make GHz applications in CMOS. In analog GHz applications it is often necessary to have access to inductors. This report describes the development of a physical model of ...

  11. Submicron organic nanofiber devices with different anode-cathode materials: A simple approach

    DEFF Research Database (Denmark)

    Henrichsen, Henrik Hartmann; Sturm, Heinz; Bøggild, Peter

    2010-01-01

    The authors present a simple general method for simultaneously producing tens of submicron electrode gaps with different cathode and anode materials on top of nanofibers, nanowires, and nanotubes, with an optional gap size variation. Using this method, an ensemble of para-hexaphenylene (p6P...

  12. Mountain pine beetle-killed lodgepole pine for the production of submicron lignocellulose fibrils

    Science.gov (United States)

    Ingrid Hoeger; Rolland Gleisner; Jose Negron; Orlando J. Rojas; J. Y. Zhu

    2014-01-01

    The elevated levels of tree mortality attributed to mountain pine beetle (MPB) (Dendroctonus ponderosae Hopkins) in western North American forests create forest management challenges. This investigation introduces the production of submicron or nanometer lignocellulose fibrils for value-added materials from the widely available resource represented by dead pines after...

  13. Computational Modelling of Gas-Particle Flows with Different Particle Morphology in the Human Nasal Cavity

    Directory of Open Access Journals (Sweden)

    Kiao Inthavong

    2009-01-01

    Full Text Available This paper summarises current studies related to numerical gas-particle flows in the human nasal cavity. Of interest are the numerical modelling requirements to consider the effects of particle morphology for a variety of particle shapes and sizes such as very small particles sizes (nanoparticles, elongated shapes (asbestos fibres, rough shapes (pollen, and porous light density particles (drug particles are considered. It was shown that important physical phenomena needed to be addressed for different particle characteristics. This included the Brownian diffusion for submicron particles. Computational results for the nasal capture efficiency for nano-particles and various breathing rates in the laminar regime were found to correlate well with the ratio of particle diffusivity to the breathing rate. For micron particles, particle inertia is the most significant property and the need to use sufficient drag laws is important. Drag correlations for fibrous and rough surfaced particles were investigated to enable particle tracking. Based on the simulated results, semi-empirical correlations for particle deposition were fitted in terms of Peclet number and inertial parameter for nanoparticles and micron particles respectively.

  14. Hydrothermal Synthesis Au-Bi2Te3 Nanocomposite Thermoelectric Film with a Hierarchical Sub-Micron Antireflection Quasi-Periodic Structure

    Directory of Open Access Journals (Sweden)

    Junlong Tian

    2015-06-01

    Full Text Available In this work, Au-Bi2Te3 nanocomposite thermoelectric film with a hierarchical sub-micron antireflection quasi-periodic structure was synthesized via a low-temperature chemical route using Troides helena (Linnaeus forewing (T_FW as the biomimetic template. This method combines chemosynthesis with biomimetic techniques, without the requirement of expensive equipment and energy intensive processes. The microstructure and the morphology of the Au-Bi2Te3 nanocomposite thermoelectric film was analyzed by X-ray diffraction (XRD, field-emission scanning-electron microscopy (FESEM, and transmission electron microscopy (TEM. Coupled the plasmon resonances of the Au nanoparticles with the hierarchical sub-micron antireflection quasi-periodic structure, the Au-Bi2Te3 nanocomposite thermoelectric film possesses an effective infrared absorption and infrared photothermal conversion performance. Based on the finite difference time domain method and the Joule effect, the heat generation and the heat source density distribution of the Au-Bi2Te3 nanocomposite thermoelectric film were studied. The heterogeneity of heat source density distribution of the Au-Bi2Te3 nanocomposite thermoelectric film opens up a novel promising technique for generating thermoelectric power under illumination.

  15. Chemical characterization and source apportionment of submicron aerosols measured in Senegal during the 2015 SHADOW campaign

    Directory of Open Access Journals (Sweden)

    L.-H. Rivellini

    2017-09-01

    Full Text Available The present study offers the first chemical characterization of the submicron (PM1 fraction in western Africa at a high time resolution, thanks to collocated measurements of nonrefractory (NR species with an Aerosol Chemical Speciation Monitor (ACSM, black carbon and iron concentrations derived from absorption coefficient measurements with a 7-wavelength Aethalometer, and total PM1 determined by a TEOM-FDMS (tapered element oscillating microbalance–filtered dynamic measurement system for mass closure. The field campaign was carried out over 3 months (March to June 2015 as part of the SHADOW (SaHAran Dust Over West Africa project at a coastal site located in the outskirts of the city of Mbour, Senegal. With an averaged mass concentration of 5.4 µg m−3, levels of NR PM1 in Mbour were 3 to 10 times lower than those generally measured in urban and suburban polluted environments. Nonetheless the first half of the observation period was marked by intense but short pollution events (NR PM1 concentrations higher than 15 µg m−3, sea breeze phenomena and Saharan desert dust outbreaks (PM10 up to 900 µg m−3. During the second half of the campaign, the sampling site was mainly under the influence of marine air masses. The air masses on days under continental and sea breeze influences were dominated by organics (36–40 %, whereas sulfate particles were predominant (40 % for days under oceanic influence. Overall, measurements showed that about three-quarters of the total PM1 were explained by NR PM1, BC (black carbon and Fe (a proxy for dust concentrations, leaving approximately one-quarter for other refractory species. A mean value of 4.6 % for the Fe ∕ PM1 ratio was obtained. Source apportionment of the organic fraction, using positive matrix factorization (PMF, highlighted the impact of local combustion sources, such as traffic and residential activities, which contribute on average to 52 % of the total organic

  16. Chemical characterization and source apportionment of submicron aerosols measured in Senegal during the 2015 SHADOW campaign

    Science.gov (United States)

    Rivellini, Laura-Hélèna; Chiapello, Isabelle; Tison, Emmanuel; Fourmentin, Marc; Féron, Anaïs; Diallo, Aboubacry; N'Diaye, Thierno; Goloub, Philippe; Canonaco, Francesco; Prévôt, André Stephan Henry; Riffault, Véronique

    2017-09-01

    The present study offers the first chemical characterization of the submicron (PM1) fraction in western Africa at a high time resolution, thanks to collocated measurements of nonrefractory (NR) species with an Aerosol Chemical Speciation Monitor (ACSM), black carbon and iron concentrations derived from absorption coefficient measurements with a 7-wavelength Aethalometer, and total PM1 determined by a TEOM-FDMS (tapered element oscillating microbalance-filtered dynamic measurement system) for mass closure. The field campaign was carried out over 3 months (March to June 2015) as part of the SHADOW (SaHAran Dust Over West Africa) project at a coastal site located in the outskirts of the city of Mbour, Senegal. With an averaged mass concentration of 5.4 µg m-3, levels of NR PM1 in Mbour were 3 to 10 times lower than those generally measured in urban and suburban polluted environments. Nonetheless the first half of the observation period was marked by intense but short pollution events (NR PM1 concentrations higher than 15 µg m-3), sea breeze phenomena and Saharan desert dust outbreaks (PM10 up to 900 µg m-3). During the second half of the campaign, the sampling site was mainly under the influence of marine air masses. The air masses on days under continental and sea breeze influences were dominated by organics (36-40 %), whereas sulfate particles were predominant (40 %) for days under oceanic influence. Overall, measurements showed that about three-quarters of the total PM1 were explained by NR PM1, BC (black carbon) and Fe (a proxy for dust) concentrations, leaving approximately one-quarter for other refractory species. A mean value of 4.6 % for the Fe / PM1 ratio was obtained. Source apportionment of the organic fraction, using positive matrix factorization (PMF), highlighted the impact of local combustion sources, such as traffic and residential activities, which contribute on average to 52 % of the total organic fraction. A new organic aerosol (OA) source

  17. Generation of MoS{sub 2} quantum dots by laser ablation of MoS{sub 2} particles in suspension and their photocatalytic activity for H{sub 2} generation

    Energy Technology Data Exchange (ETDEWEB)

    Baldoví, Herme G.; Latorre-Sánchez, Marcos; Esteve-Adell, Iván [Universitat Politècnica de València, Instituto Universitario de Tecnología Química CSIC-UPV and Departamento de Química (Spain); Khan, Anish; Asiri, Abdullah M. [King Abdulaziz University, Center of Excellence for Advanced Materials Research (Saudi Arabia); Kosa, Samia A. [King Abdulaziz University, Chemistry Department, Faculty of Science (Saudi Arabia); Garcia, Hermenegildo, E-mail: hgarcia@qim.upv.es [Universitat Politècnica de València, Instituto Universitario de Tecnología Química CSIC-UPV and Departamento de Química (Spain)

    2016-08-15

    MoS{sub 2} quantum dots (QDs) have been obtained in colloidal suspensions by 532 nm laser ablation (7 ns fwhp/pulse, 50 mJ/pulse) of commercial MoS{sub 2} particles in acetonitrile. High-resolution transmission electron microscopy images show a lateral size distribution from 5 to 20 nm, but a more homogeneous particle size of 20 nm can be obtained by silica gel chromatography purification in acetonitrile. MoS{sub 2} QDs obtained by laser ablation are constituted by 3–6 MoS{sub 2} layers (1.8–4 nm thickness) and exhibit photoluminescence whose λ{sub PL} varies from 430 to 530 nm depending on the excitation wavelength. As predicted by theory, the confinement effect and the larger periphery in MoS{sub 2} QDs increasing the bandgap and having catalytically active edges are reflected in an enhancement of the photocatalytic activity for H{sub 2} generation upon UV–Vis irradiation using CH{sub 3}OH as sacrificial electron donor due to the increase in the reduction potential of conduction band electrons and the electron transfer kinetics.

  18. Time-specific measurements of energy deposition from radiation fields in simulated sub-micron tissue volumes

    Energy Technology Data Exchange (ETDEWEB)

    Famiano, M.A.

    1997-07-07

    A tissue-equivalent spherical proportional counter is used with a modified amplifier system to measure specific energy deposited from a uniform radiation field for short periods of time ({approximately}1 {micro}s to seconds) in order to extrapolate to dose in sub-micron tissue volumes. The energy deposited during these time intervals is compared to biological repair processes occurring within the same intervals after the initial energy deposition. The signal is integrated over a variable collection time which is adjusted with a square-wave pulse. Charge from particle passages is collected on the anode during the period in which the integrator is triggered, and the signal decays quickly to zero after the integrator feedback switch resets; the process repeats for every triggering pulse. Measurements of energy deposited from x rays, {sup 137}Cs gamma rays, and electrons from a {sup 90}Sr/{sup 90}Y source for various time intervals are taken. Spectral characteristics as a function of charge collection time are observed and frequency plots of specific energy and collection time-interval are presented. In addition, a threshold energy flux is selected for each radiation type at which the formation of radicals (based on current measurements) in mammalian cells equals the rate at which radicals are repaired.

  19. Chemical vapor deposition of silicon nanodots on TiO{sub 2} submicronic powders in vibrated fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Cadoret, L. [Laboratoire de Genie Chimique, UMR CNRS 5503, Universite de Toulouse, ENSIACET/INPT, 4 allee Emile Monso, BP 74233, 31432 Toulouse Cedex 4 (France); Rossignol, C.; Dexpert-Ghys, J. [CEMES, UPR CNRS 8011, UPS-Toulouse, 29 rue Jean Marvig, 31055 Toulouse Cedex 4 (France); Caussat, B., E-mail: Brigitte.Caussat@ensiacet.fr [Laboratoire de Genie Chimique, UMR CNRS 5503, Universite de Toulouse, ENSIACET/INPT, 4 allee Emile Monso, BP 74233, 31432 Toulouse Cedex 4 (France)

    2010-06-15

    Silicon nanodots have been deposited on TiO{sub 2} submicronic powders in a vibrated fluidized bed chemical vapor deposition (FBCVD) reactor from silane SiH{sub 4}. Deposition conditions involving very low deposition rates have been studied. After treatment, powders are under the form of micronic agglomerates. In the operating range tested, this agglomerates formation mainly depends on the fluidization conditions and not on the CVD parameters. The best results have been obtained for anatase TiO{sub 2} powders for which the conditions of fluidization have been the most optimized. For these anatase powders, agglomerates are porous. SEM and TEM imaging prove that silicon nanodots (8-10 nm in size) have been deposited on the surface of particles and that this deposition is uniform on the whole powders and conformal around each grain, even if not fully continuous. Raman spectroscopy shows that the TiO{sub 2} powders have been partially reduced into TiO{sub 2-x} during deposition. The TiO{sub 2} stoichiometry can be recovered by annealing under air, and IR spectroscopy indicates that the deposited silicon nanodots have been at least partly oxidized into SiO{sub 2} after this annealing.

  20. Generator. Generator

    Energy Technology Data Exchange (ETDEWEB)

    Knoedler, R.; Bossmann, H.P.

    1992-03-12

    The invention refers to a thermo-electric generator, whose main part is a sodium concentration cell. In conventional thermo-electric generators of this kind, the sodium moving from a hot space to a colder space must be transported back to the hot space via a circulation pipe and a pump. The purpose of the invention is to avoid the disadvantages of this return transport. According to the invention, the thermo-electric generator is supported so that it can rotate, so that the position of each space relative to its propinquity to the heat source can be changed at any time.

  1. Selection of quasi-monodisperse super-micron aerosol particles

    Science.gov (United States)

    Rösch, Michael; Pfeifer, Sascha; Wiedensohler, Alfred; Stratmann, Frank

    2014-05-01

    Size-segregated quasi monodisperse particles are essential for e.g. fundamental research concerning cloud microphysical processes. Commonly a DMA (Differential Mobility Analyzer) is used to produce quasi-monodisperse submicron particles. Thereto first, polydisperse aerosol particles are bipolarly charged by a neutralizer, and then selected according to their electrical mobility with the DMA [Knutson et al. 1975]. Selecting a certain electrical mobility with a DMA results in a particle size distribution, which contains singly charged particles as well as undesired multiply charged larger particles. Often these larger particles need to either be removed from the generated aerosol or their signals have to be corrected for in the data inversion and interpretation process. This problem becomes even more serious when considering super-micron particles. Here we will present two different techniques for generating quasi-monodisperse super-micron aerosol particles with no or only an insignificant number of larger sized particles being present. First, we use a combination of a cyclone with adjustable aerodynamic cut-off diameter and our custom-built Maxi-DMA [Raddatz et al. 2013]. The cyclone removes particles larger than the desired ones prior to mobility selection with the DMA. This results in a reduction of the number of multiply charged particles of up to 99.8%. Second, we utilize a new combination of cyclone and PCVI (Pumped Counterflow Virtual Impactor), which is based on purely inertial separation and avoids particle charging. The PCVI instrument was previously described by Boulter et al. (2006) and Kulkarni et al. (2011). With our two setups we are able to produce quasi-monodisperse aerosol particles in the diameter range from 0.5 to 4.4 µm without a significant number of larger undesired particles being present. Acknowledgements: This work was done within the framework of the DFG funded Ice Nucleation research UnIT (INUIT, FOR 1525) under WE 4722/1-1. References

  2. Filtration of submicrometer particles by pelagic tunicates.

    Science.gov (United States)

    Sutherland, Kelly R; Madin, Laurence P; Stocker, Roman

    2010-08-24

    Salps are common in oceanic waters and have higher per-individual filtration rates than any other zooplankton filter feeder. Although salps are centimeters in length, feeding via particle capture occurs on a fine, mucous mesh (fiber diameter d approximately 0.1 microm) at low velocity (U = 1.6 +/- 0.6 cmxs(-1), mean +/- SD) and is thus a low Reynolds-number (Re approximately 10(-3)) process. In contrast to the current view that particle encounter is dictated by simple sieving of particles larger than the mesh spacing, a low-Re mathematical model of encounter rates by the salp feeding apparatus for realistic oceanic particle-size distributions shows that submicron particles, due to their higher abundances, are encountered at higher rates (particles per time) than larger particles. Data from feeding experiments with 0.5-, 1-, and 3-microm diameter polystyrene spheres corroborate these findings. Although particles larger than 1 microm (e.g., flagellates, small diatoms) represent a larger carbon pool, smaller particles in the 0.1- to 1-microm range (e.g., bacteria, Prochlorococcus) may be more quickly digestible because they present more surface area, and we find that particles smaller than the mesh size (1.4 microm) can fully satisfy salp energetic needs. Furthermore, by packaging submicrometer particles into rapidly sinking fecal pellets, pelagic tunicates can substantially change particle-size spectra and increase downward fluxes in the ocean.

  3. Two-Dimensional Analysis of Narrow Gate Effects in Micron and Submicron Mosfets

    Science.gov (United States)

    Chung, Shao-Shiun

    Variations of the device characteristics due to the geometry effects in narrow gate MOSFETs, such as threshold voltage shift and subthreshold characteristics, are important factors in designing next generation MOS-VLSI circuits. It is well known that numerical methods, using the exact 2 -D solutions of the transport equation and Poisson's equation for studying the geometry effect of small MOSFETs, are more accurate than simple charge-control analysis. The 2-D numerical model of Ji and Sah demonstrated important design features of the threshold voltage of narrow gate MOSFETs. However, studies of MOSFET characteristics using 2-D numerical analysis, which take into account the effects of all the device parameters, such as gate oxide thickness, backgate bias, and substrate doping, are lacking. Particularly, the analysis of the subthreshold characteristic for narrow gate MOSFETs was not reported before. The ideas in Ji-Sah's depletion approximation model, as well as their analysis method, have been extended to take into account the electrons and holes in the numerical solution of Poisson's equation. Using a super-minicomputer (VAX-11/750), a new 2-D program (NAROMOS-II) using the finite difference method has been developed in this thesis. Based on the 2-D results and device physics, a threshold voltage model and a subthreshold characteristics model for CAD of MOS-VLSI are proposed to describe the geometry effect of narrow gate MOSFETs. These models are based on the extraction of four model parameters: two for the threshold voltage model, and two for the subthreshold characteristics model. All of these model parameters can be verified numerically or experimentally. Results for the threshold voltage model compare favorably with numerical and reported experimental data. Dependences of the device performance on the device parameters are then investigated, using the above analysis techniques. Simple forms of the models of the threshold voltage shift and subthreshold

  4. Influence of locational states of submicron fibers added into matrix on mechanical properties of plain-woven Carbon Fiber Composite

    National Research Council Canada - National Science Library

    Soichiro Kumamoto; Kazuya Okubo; Toru Fujii

    2016-01-01

    The aim of this study was to show the influence of locational states of submicron fibers added into epoxy matrix on mechanical properties of modified plane-woven carbon fiber reinforced plastic (CFRP...

  5. Generator. Generator

    Energy Technology Data Exchange (ETDEWEB)

    Bossmann, H.P.; Knoedler, R.

    1992-03-12

    The invention refers to a thermo-electric generator, which contains sodium as the means of heat transport. The sodium moves from the space of higher temperature through a space into the space of lower temperature. One can do without a pump for transporting the sodium back from the space of lower temperature to the space of higher temperature, as the thermo-electric generator can rotate around an axis. It is therefore possible to interchange the position of the two spaces relative to the heat source.

  6. Effective Use of Focused Ion Beam (FIB) in Investigating Fundamental Mechanical Properties of Metals at the Sub-Micron Scale

    OpenAIRE

    Greer, Julia R.

    2006-01-01

    Recent advances in the 2-beam focused ion beams technology (FIB) have enabled researchers to not only perform high-precision nanolithography and micro-machining, but also to apply these novel fabrication techniques to investigating a broad range of materials' properties at the submicron and nano-scales. In our work, the FIB is utilized in manufacturing of sub-micron cylinders, or nano-pillars, as well as of TEM cross-sections to directly investigate plasticity of metals at thes...

  7. Pseudo-spectral Maxwell solvers for an accurate modeling of Doppler harmonic generation on plasma mirrors with Particle-In-Cell codes

    CERN Document Server

    Blaclard, G; Lehe, R; Vay, J L

    2016-01-01

    With the advent of PW class lasers, the very large laser intensities attainable on-target should enable the production of intense high order Doppler harmonics from relativistic laser-plasma mirrors interactions. At present, the modeling of these harmonics with Particle-In-Cell (PIC) codes is extremely challenging as it implies an accurate description of tens of harmonic orders on a a broad range of angles. In particular, we show here that standard Finite Difference Time Domain (FDTD) Maxwell solvers used in most PIC codes partly fail to model Doppler harmonic generation because they induce numerical dispersion of electromagnetic waves in vacuum which is responsible for a spurious angular deviation of harmonic beams. This effect was extensively studied and a simple toy-model based on Snell-Descartes law was developed that allows us to finely predict the angular deviation of harmonics depending on the spatio-temporal resolution and the Maxwell solver used in the simulations. Our model demonstrates that the miti...

  8. Particle Pollution

    Science.gov (United States)

    ... Your Health Particle Pollution Public Health Issues Particle Pollution Recommend on Facebook Tweet Share Compartir Particle pollution — ... see them in the air. Where does particle pollution come from? Particle pollution can come from two ...

  9. Continuous Draw Spinning of Extra-Long Silver Submicron Fibers with Micrometer Patterning Capability.

    Science.gov (United States)

    Bai, Xiaopeng; Liao, Suiyang; Huang, Ya; Song, Jianan; Liu, Zhenglian; Fang, Minghao; Xu, Chencheng; Cui, Yi; Wu, Hui

    2017-03-08

    Ultrathin metal fibers can serve as highly conducting and flexible current and heat transport channels, which are essential for numerous applications ranging from flexible electronics to energy conversion. Although industrial production of metal fibers with diameters of down to 2 μm is feasible, continuous production of high-quality and low-cost nanoscale metal wires is still challenging. Herein, we report the continuous draw spinning of highly conductive silver submicron fibers with the minimum diameter of ∼200 nm and length of more than kilometers. We obtained individual AgNO3/polymer fibers by continuous drawing from an aqueous solution at a speed of up to 8 m/s. With subsequent heat treatment, freestanding Ag submicron fibers with high mechanical flexibility and electric conductivity have been obtained. Woven mats of aligned Ag submicron fibers were used as transparent electrodes with high flexibility and high performance with sheet resistance of 7 Ω sq(-1) at a transparency of 96%. Continuous draw spinning opened new avenues for scalable, flexible, and ultralow-cost fabrication of extra-long conductive ultrathin metal fibers.

  10. Directed assembly of conducting polymers on sub-micron templates by electrical fields

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Jia; Wei, Ming [National Science Foundation (NSF) Nanoscale Science and Engineering Center for High-Rate Nanomanufacturing, University of Massachusetts Lowell, Lowell, MA 01854 (United States); Busnaina, Ahmed [National Science Foundation (NSF) Nanoscale Science and Engineering Center for High-Rate Nanomanufacturing, Northeastern University, Boston, MA 02115 (United States); Barry, Carol [National Science Foundation (NSF) Nanoscale Science and Engineering Center for High-Rate Nanomanufacturing, University of Massachusetts Lowell, Lowell, MA 01854 (United States); Mead, Joey, E-mail: Joey_Mead@uml.edu [National Science Foundation (NSF) Nanoscale Science and Engineering Center for High-Rate Nanomanufacturing, University of Massachusetts Lowell, Lowell, MA 01854 (United States)

    2013-02-20

    Highlights: Black-Right-Pointing-Pointer Nanoscale patterns with dimensions of assembled PANi down to 100 nm were fabricated. Black-Right-Pointing-Pointer We use electrophoretic and dielectrophoretic assembly to deposit PANi. Black-Right-Pointing-Pointer Electrophoretic and dielectrophoretic assembly of PANi finished in less than 1 min. Black-Right-Pointing-Pointer Effect of process parameters on assembly of PANi onto nanoscale pattern was studied. Black-Right-Pointing-Pointer The assembled PANi can be transferred to other flexible substrates. - Abstract: Patterning of conducting polymer into sub-micron patterns over large areas at high rate and low cost is significant for commercial manufacturing of novel devices. Electrophoretic and dielectrophoretic assembly provide an easily scaled approach with high fabrication rates. In this work, electrophoretic and dielectrophoretic assembly were used to assemble polyaniline (PANi) into multiscale sub-micron size patterns in less than 1 min. The process was controlled by assembly time, amplitude, and frequency of the electric field. Dielectrophoretic assembly is preferable for manufacturing as it reduces damage to the templates used to control the assembly. Using this method, sub-micron patterns with dimensions of the assembled PANi down to 100 nm were fabricated over large areas in short times. The assembled PANi was further transferred to other flexible polymer substrates by a thermoforming process, providing a fast, easily controlled and promising approach for fabrication of nanoscale devices.

  11. The study to reduce the hemolysis side effect of puerarin by a submicron emulsion delivery system.

    Science.gov (United States)

    Yue, Peng-Fei; Hai-Long Yuan, Hai-Long; Zhu, Wei-Feng; Cong, Long-Bo; Xie, Huan; Liu, Zhi-Guo; Wang, Lu-Jun; Xiao, Xiao-He

    2008-01-01

    A safe and effective delivery system with a submicron emulsion for puerarin was studied. Puerarin submicron emulsion was prepared by a novel complex-phase inversion-high press homogenization technology. The mechanism to reduce the hemolysis side effect of puerarin was studied by blood cell counts in rabbits. The average diameter, zeta potential and entrapment efficiency of the emulsion prepared was 198.14+/-8.61 nm, -29.45+/-1.47 mV, 87.32+/-0.34%, respectively. Compared with control group, the red blood cell values, packed cell volume, plasma hemoglobin level, haptoglobin level and osmotic fragility of puerarin i.v. group was significantly different (pemulsion group were not significantly different (p>0.05) in contrast to control group. Such observations indicated that the intravascular hemolysis occurred at 42, 43 d in puerarin i.v. group rabbits, the hemolysis did not occur for puerarin emulsion group rabbits. As an explanation for these results, it was proposed that the puerarin was either incorporated into the lipophilic core or intercalated between the phospholipid molecules at the interface. It could be concluded that puerarin submicron emulsions prepared markedly reduced the hemolysis effect of puerarin.

  12. A flow cytometry-based submicron-sized bacterial detection system using a movable virtual wall.

    Science.gov (United States)

    Choi, Hyoungseon; Jeon, Chang Su; Hwang, Inseong; Ko, Juhui; Lee, Saram; Choo, Jaebum; Boo, Jin-Hyo; Kim, Hee Chan; Chung, Taek Dong

    2014-07-07

    Detection of pathogenic bacteria requires a sensitive, accurate, rapid, and portable device. Given that lethal microbes are of various sizes, bacterial sensors based on DC (direct current) impedance on chips should be equipped with channels with commensurate cross sections. When it comes to counting and interrogation of individual bacteria on a microfluidic chip, very narrow channels are required, which are neither easy nor cost-effective to fabricate. Here, we report a flow cytometry-based submicron-sized bacterial detection system using a movable virtual wall made of a non-conducting fluid. We show that the effective dimension of a microfluidic channel can be adjusted by varying the respective flow rates of a sample solution as well as the liquid wall therein. Using such a virtual wall, we have successfully controlled the channel width and detected submicron-sized Francisella tularensis, a lethal, tularemia-causing bacterium. Since the system is capable of monitoring changes in DC impedance and fluorescence simultaneously, we were also able to discriminate between different types of bacterial mixtures containing F. tularensis and E. coli BL21 that have different gamuts of size distributions. The proposed flow cytometry-based system represents a promising way to detect bacteria including, but not limited to, submicron-sized pathogenic microbes.

  13. Photocatalytic and Adsorption Performances of Faceted Cuprous Oxide (Cu₂O) Particles for the Removal of Methyl Orange (MO) from Aqueous Media.

    Science.gov (United States)

    Ho, Weng Chye Jeffrey; Tay, Qiuling; Qi, Huan; Huang, Zhaohong; Li, Jiao; Chen, Zhong

    2017-04-23

    Particles of sub-micron size possess significant capacity to adsorb organic molecules from aqueous media. Semiconductor photocatalysts in particle form could potentially be utilized for dye removal through either physical adsorption or photo-induced chemical process. The photocatalytic and adsorption capabilities of Cu₂O particles with various exposed crystal facets have been studied through separate adsorption capacity test and photocatalytic degradation test. These crystals display unique cubic, octahedral, rhombic dodecahedral, and truncated polyhedral shapes due to specifically exposed crystal facet(s). For comparison, Cu₂O particles with no clear exposed facets were also prepared. The current work confirms that the surface charge critically affects the adsorption performance of the synthesized Cu₂O particles. The octahedral shaped Cu₂O particles, with exposed {111} facets, possess the best adsorption capability of methyl orange (MO) dye due to the strongest positive surface charge among the different types of particles. In addition, we also found that the adsorption of MO follows the Langmuir monolayer mechanism. The octahedral particles also performed the best in photocatalytic dye degradation of MO under visible light irradiation because of the assistance from dye absorption. On top of the photocatalytic study, the stability of these Cu₂O particles during the photocatalytic processes was also investigated. Cu(OH)₂ and CuO are the likely corrosion products found on the particle surface after the photocorrosion in MO solution. By adding hole scavengers in the solution, the photocorrosion of Cu₂O was greatly reduced. This observation confirms that the photocatalytically generated holes were responsible for the photocorrosion of Cu₂O.

  14. Aerodynamic particle size analysis of aerosols from pressurized metered-dose inhalers: Comparison of andersen 8-stage cascade impactor, next generation pharmaceutical impactor, and model 3321 aerodynamic particle sizer aerosol spectrometer

    OpenAIRE

    Mitchell, Jolyon P.; Nagel, Mark W.; Wiersema, Kimberly J.; Doyle, Cathy C.

    2003-01-01

    The purpose of this research was to compare three different methods for the aerodynamic assessment of (1) chloroflurocarbon (CFC)-fluticasone propionate (Flovent), (2) CFC-sodium cromoglycate (Intal), and (3) hydrofluoroalkane (HFA)-beclomethasone dipropionate (Qvar) delivered by pressurized metered dose inhaler. Particle size distributions were compared determining mass median aerodynamic diameter (MMAD), geometric standard deviation (GSD), and fine particle fraction

  15. Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%.

    KAUST Repository

    Kim, Hui-Seon

    2012-08-21

    We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH(3)NH(3))PbI(3) as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI(2) and deposited onto a submicron-thick mesoscopic TiO(2) film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (J(SC)) exceeding 17 mA/cm(2), an open circuit photovoltage (V(OC)) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH(3)NH(3))PbI(3) NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO(2) film. The use of a solid hole conductor dramatically improved the device stability compared to (CH(3)NH(3))PbI(3) -sensitized liquid junction cells.

  16. Lead Iodide Perovskite Sensitized All-Solid-State Submicron Thin Film Mesoscopic Solar Cell with Efficiency Exceeding 9%

    Science.gov (United States)

    Kim, Hui-Seon; Lee, Chang-Ryul; Im, Jeong-Hyeok; Lee, Ki-Beom; Moehl, Thomas; Marchioro, Arianna; Moon, Soo-Jin; Humphry-Baker, Robin; Yum, Jun-Ho; Moser, Jacques E.; Grätzel, Michael; Park, Nam-Gyu

    2012-01-01

    We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH3NH3)PbI3 as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI2 and deposited onto a submicron-thick mesoscopic TiO2 film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (JSC) exceeding 17 mA/cm2, an open circuit photovoltage (VOC) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH3NH3)PbI3 NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO2 film. The use of a solid hole conductor dramatically improved the device stability compared to (CH3NH3)PbI3 -sensitized liquid junction cells. PMID:22912919

  17. Applying digital particle image velocimetry to animal-generated flows : Traps, hurdles and cures in mapping steady and unsteady flows in Re regimes between 10(-2) and 10(5)

    NARCIS (Netherlands)

    Stamhuis, EJ; Videler, JJ; van Duren, LA; Muller, UK

    2002-01-01

    Digital particle image velocimetry (DPIV) has been applied to animal-generated flows since 1993 to map the flow patterns and vortex wakes produced by a range of feeding and swimming aquatic animals, covering a Re range of 10(-2)-10(5). In this paper, the special circumstances, problems and some

  18. FY 2000 Industrial science and technology research and development themes - cooperative project with academic circles. Report on the results of research and development of technologies for creating new bioaffinity molecules using submicron beads (Development of technologies for rational use of energy); 2000 nendo biryushi riyogata seitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the research and development for creating new bioaffinity molecules using submicron beads. The program for development of technology for analyzing chemical-biomolecule complexes using submicron affinity beads has developed a detachable linker which allows the complex, composed of ligand on the affinity latex particle surfaces and receptor bound thereto, to be detached directly from the particles, and also developed the prototype of magnetite-containing polymer particles with a diameter of submicron order, which facilitate recovery of the affinity latex. The program for development of technology to create chemical substances with new functions has successfully constructed the focused library composed of 400 compounds based on the split and pool method for FR225659 as a glucose modulator, chosen as the target material. It also has established the method of synthesizing opioid alkaloid as the target compound on the solid phase, and synthesized 39 opioid compounds with condensed indol rings, having diverse of several substituents. (NEDO)

  19. Evaluating model parameterizations of submicron aerosol scattering and absorption with in situ data from ARCTAS 2008

    Directory of Open Access Journals (Sweden)

    M. J. Alvarado

    2016-07-01

    Full Text Available Accurate modeling of the scattering and absorption of ultraviolet and visible radiation by aerosols is essential for accurate simulations of atmospheric chemistry and climate. Closure studies using in situ measurements of aerosol scattering and absorption can be used to evaluate and improve models of aerosol optical properties without interference from model errors in aerosol emissions, transport, chemistry, or deposition rates. Here we evaluate the ability of four externally mixed, fixed size distribution parameterizations used in global models to simulate submicron aerosol scattering and absorption at three wavelengths using in situ data gathered during the 2008 Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS campaign. The four models are the NASA Global Modeling Initiative (GMI Combo model, GEOS-Chem v9-02, the baseline configuration of a version of GEOS-Chem with online radiative transfer calculations (called GC-RT, and the Optical Properties of Aerosol and Clouds (OPAC v3.1 package. We also use the ARCTAS data to perform the first evaluation of the ability of the Aerosol Simulation Program (ASP v2.1 to simulate submicron aerosol scattering and absorption when in situ data on the aerosol size distribution are used, and examine the impact of different mixing rules for black carbon (BC on the results. We find that the GMI model tends to overestimate submicron scattering and absorption at shorter wavelengths by 10–23 %, and that GMI has smaller absolute mean biases for submicron absorption than OPAC v3.1, GEOS-Chem v9-02, or GC-RT. However, the changes to the density and refractive index of BC in GC-RT improve the simulation of submicron aerosol absorption at all wavelengths relative to GEOS-Chem v9-02. Adding a variable size distribution, as in ASP v2.1, improves model performance for scattering but not for absorption, likely due to the assumption in ASP v2.1 that BC is present at a constant mass

  20. Generation of urban road dust from anti-skid and asphalt concrete aggregates.

    Science.gov (United States)

    Tervahattu, Heikki; Kupiainen, Kaarle J; Räisänen, Mika; Mäkelä, Timo; Hillamo, Risto

    2006-04-30

    Road dust forms an important component of airborne particulate matter in urban areas. In many winter cities the use of anti-skid aggregates and studded tires enhance the generation of mineral particles. The abrasion particles dominate the PM10 during springtime when the material deposited in snow is resuspended. This paper summarizes the results from three test series performed in a test facility to assess the factors that affect the generation of abrasion components of road dust. Concentrations, mass size distribution and composition of the particles were studied. Over 90% of the particles were aluminosilicates from either anti-skid or asphalt concrete aggregates. Mineral particles were observed mainly in the PM10 fraction, the fine fraction being 12% and submicron size being 6% of PM10 mass. The PM10 concentrations increased as a function of the amount of anti-skid aggregate dispersed. The use of anti-skid aggregate increased substantially the amount of PM10 originated from the asphalt concrete. It was concluded that anti-skid aggregate grains contribute to pavement wear. The particle size distribution of the anti-skid aggregates had great impact on PM10 emissions which were additionally enhanced by studded tires, modal composition, and texture of anti-skid aggregates. The results emphasize the interaction of tires, anti-skid aggregate, and asphalt concrete pavement in the production of dust emissions. They all must be taken into account when measures to reduce road dust are considered. The winter maintenance and springtime cleaning must be performed properly with methods which are efficient in reducing PM10 dust.

  1. Variations in the chemical composition of the submicron aerosol and in the sources of the organic fraction at a regional background site of the Po Valley (Italy)

    Science.gov (United States)

    Bressi, Michael; Cavalli, Fabrizia; Belis, Claudio A.; Putaud, Jean-Philippe; Fröhlich, Roman; Martins dos Santos, Sebastiao; Petralia, Ettore; Prévôt, André S. H.; Berico, Massimo; Malaguti, Antonella; Canonaco, Francesco

    2016-10-01

    Fine particulate matter (PM) levels and resulting impacts on human health are in the Po Valley (Italy) among the highest in Europe. To build effective PM abatement strategies, it is necessary to characterize fine PM chemical composition, sources and atmospheric processes on long timescales (> months), with short time resolution (organic fraction. Although previous studies have been conducted in this region, none of them addressed all these aspects together. For the first time in the Po Valley, we investigate the chemical composition of nonrefractory submicron PM (NR-PM1) with a time resolution of 30 min at the regional background site of Ispra during 1 full year, using the Aerodyne Aerosol Chemical Speciation Monitor (ACSM) under the most up-to-date and stringent quality assurance protocol. The identification of the main components of the organic fraction is made using the Multilinear-Engine 2 algorithm implemented within the latest version of the SoFi toolkit. In addition, with the aim of a potential implementation of ACSM measurements in European air quality networks as a replacement of traditional filter-based techniques, parallel multiple offline analyses were carried out to assess the performance of the ACSM in the determination of PM chemical species regulated by air quality directives. The annual NR-PM1 level monitored at the study site (14.2 µg m-3) is among the highest in Europe and is even comparable to levels reported in urban areas like New York City and Tokyo. On the annual basis, submicron particles are primarily composed of organic aerosol (OA, 58 % of NR-PM1). This fraction was apportioned into oxygenated OA (OOA, 66 %), hydrocarbon-like OA (HOA, 11 % of OA) and biomass burning OA (BBOA, 23 %). Among the primary sources of OA, biomass burning (23 %) is thus bigger than fossil fuel combustion (11 %). Significant contributions of aged secondary organic aerosol (OOA) are observed throughout the year. The unexpectedly high degree of oxygenation

  2. Comparison of Aerodynamic Particle Size Distribution Between a Next Generation Impactor and a Cascade Impactor at a Range of Flow Rates.

    Science.gov (United States)

    Yoshida, Hiroyuki; Kuwana, Akemi; Shibata, Hiroko; Izutsu, Ken-Ichi; Goda, Yukihiro

    2017-04-01

    Wide variation in respiratory flow rates between patients emphasizes the importance of evaluating the aerodynamic particle size distribution (APSD) of dry powder inhaler (DPI) using a multi-stage impactor at different flow rates. US Pharmacopeia recently listed modified configurations of the Andersen cascade impactor (ACI) and new sets of cut-off diameter specifications for the operation at flow rates of 60 and 90 L/min. The purpose of this study was to clarify the effect of these changes on the APSD of DPI products at varied flow rates. We obtained APSD profiles of four DPIs and device combinations, Relenza®-Diskhaler® (GlaxoSmithKline Co.), Seebri®-Breezhaler® (Novartis Pharma Co.), Pulmicort®-Turbuhaler® (Astrazeneca Co.), and Spiriva®-Handihaler® (Nippon Boehringer Ingelheim Co.) using Next Generation Impactors (NGIs) and ACIs at flow rates from 28.3 to 90 L/min to evaluate the difference in the use of previous and new sets of cut-off diameter specifications. Processing the data using the new specifications for ACI apparently reduced large differences in APSD obtained by NGI and ACI with the previous specifications at low and high flow rates in all the DPIs. Selecting the appropriate configuration of ACI corresponding to the flow rate provided comparable APSD profiles of Pulmicort®-Turbuhaler® to those using NGIs at varied flow rates. The results confirmed the relevance of the current US Pharmacopeia specifications for ACI analysis in obtaining APSD profiles of DPI products at wide flow rates.

  3. Particle physics

    CERN Document Server

    Kennedy, Eugene

    2012-01-01

    Stimulated by the Large Hadron Collider and the search for the elusive Higgs Boson, interest in particle physics continues at a high level among scientists and the general public. This book includes theoretical aspects, with chapters outlining the generation model and a charged Higgs boson model as alternative scenarios to the Standard Model. An introduction is provided to postulated axion photon interactions and associated photon dispersion in magnetized media. The complexity of particle physics research requiring the synergistic combination of theory, hardware and computation is described in terms of the e-science paradigm. The book concludes with a chapter tackling potential radiation hazards associated with extremely weakly interacting neutrinos if produced in copious amounts with future high-energy muon-collider facilities.

  4. Influence of locational states of submicron fibers added into matrix on mechanical properties of plain-woven Carbon Fiber Composite

    Science.gov (United States)

    Kumamoto, Soichiro; Okubo, Kazuya; Fujii, Toru

    2016-01-01

    The aim of this study was to show the influence of locational states of submicron fibers added into epoxy matrix on mechanical properties of modified plane-woven carbon fiber reinforced plastic (CFRP). To change the locational states of submicron fibers, two kinds of fabrication processes were applied in preparing specimen by hand lay-up method. Submicron fibers were simply added into epoxy resin with ethanol after they were stirred by a dispersion process using homogenizer to be located far from the interface between reinforcement and matrix. In contrast, submicron fibers were attached onto the carbon fibers by injecting from a spray nozzle accompanying with ethanol to be located near the interface, after they were tentatively contained in ethanol. The plain-woven CFRP plates were fabricated by hand lay-up method and cured at 80 degree-C for 1 hour and then at 150 degree-C for 3 hours. After curing, the plain-woven CFRP plates were cut into the dimension of specimen. Tensile shear strength and Mode-II fracture toughness of CFRP were determined by tensile lap-shear test and End-notched flexure(ENF) test, respectively. When submicron fibers were located far from the interface between carbon fibers and epoxy resin, tensile shear strength and Mode-II fracture toughness of CFRP were improved 30% and 18% compared with those of unmodified case. The improvement ratio in modified case was rather low (about few percentages) in the case where submicron fibers were located near the interface. The result suggested that crack propagation should be prevented when submicron fibers were existed far from the interface due to the effective stress state around the crack tip.

  5. Influence of locational states of submicron fibers added into matrix on mechanical properties of plain-woven Carbon Fiber Composite

    Directory of Open Access Journals (Sweden)

    Kumamoto Soichiro

    2016-01-01

    Full Text Available The aim of this study was to show the influence of locational states of submicron fibers added into epoxy matrix on mechanical properties of modified plane-woven carbon fiber reinforced plastic (CFRP. To change the locational states of submicron fibers, two kinds of fabrication processes were applied in preparing specimen by hand lay-up method. Submicron fibers were simply added into epoxy resin with ethanol after they were stirred by a dispersion process using homogenizer to be located far from the interface between reinforcement and matrix. In contrast, submicron fibers were attached onto the carbon fibers by injecting from a spray nozzle accompanying with ethanol to be located near the interface, after they were tentatively contained in ethanol. The plain-woven CFRP plates were fabricated by hand lay-up method and cured at 80 degree-C for 1 hour and then at 150 degree-C for 3 hours. After curing, the plain-woven CFRP plates were cut into the dimension of specimen. Tensile shear strength and Mode-II fracture toughness of CFRP were determined by tensile lap-shear test and End-notched flexure(ENF test, respectively. When submicron fibers were located far from the interface between carbon fibers and epoxy resin, tensile shear strength and Mode-II fracture toughness of CFRP were improved 30% and 18% compared with those of unmodified case. The improvement ratio in modified case was rather low (about few percentages in the case where submicron fibers were located near the interface. The result suggested that crack propagation should be prevented when submicron fibers were existed far from the interface due to the effective stress state around the crack tip.

  6. Electromagnetic needles with submicron pole tip radii for nanomanipulation of biomolecules and living cells

    Science.gov (United States)

    Matthews, Benjamin D.; LaVan, David A.; Overby, Darryl R.; Karavitis, John; Ingber, Donald E.

    2004-10-01

    We describe the design and fabrication of a temperature-controlled electromagnetic microneedle (EMN) to generate custom magnetic field gradients for biomedical and biophysical applications. An electropolishing technique was developed to sharpen the EMN pole tip to any desired radius between 100 nm and 20 μm. The EMN can be used to apply strong static or dynamic forces (>50nN) to micrometer- or nanometer-sized magnetic beads without producing significant heating or needle movement. Large tip radii (20 μm) allow magnetic force application to multiple magnetic beads over a large area, while small radii (0.1-6 μm) can be used to selectively pull or capture single magnetic beads from within a large population of similar particles. The customizable EMN is thus well suited for micro- and nanomanipulation of magnetic particles linked to biomolecules or living cells.

  7. Characteristics and sources of submicron aerosols above the urban canopy (260 m) in Beijing, China during 2014 APEC summit

    Science.gov (United States)

    Chen, C.; Sun, Y. L.; Xu, W. Q.; Du, W.; Zhou, L. B.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Gao, Z. Q.; Zhang, Q.; Worsnop, D. R.

    2015-08-01

    The megacity of Beijing has experienced frequent severe fine particle pollution during the last decade. Although the sources and formation mechanisms of aerosol particles have been extensively investigated on the basis of ground measurements, real-time characterization of aerosol particle composition and sources above the urban canopy in Beijing is rare. In this study, we conducted real-time measurements of non-refractory submicron aerosol (NR-PM1) composition at 260 m at the 325 m Beijing Meteorological Tower (BMT) from 10 October to 12 November 2014, by using an aerosol chemical speciation monitor (ACSM) along with synchronous measurements of size-resolved NR-PM1 composition at near ground level using a High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS). The NR-PM1 composition above the urban canopy was dominated by organics (46 %), followed by nitrate (27 %) and sulfate (13 %). The high contribution of nitrate and high NO3-/SO42- mass ratios illustrate an important role of nitrate in particulate matter (PM) pollution during the study period. The organic aerosol (OA) was mainly composed by secondary OA (SOA), accounting for 61 % on an average. Different from that measured at the ground site, primary OA (POA) correlated moderately with SOA, likely suggesting a high contribution from regional transport above the urban canopy. The Asia-Pacific Economic Cooperation (APEC) summit with strict emission controls provides a unique opportunity to study the impacts of emission controls on aerosol chemistry. All aerosol species were shown to have significant decreases of 40-80 % during APEC from those measured before APEC, suggesting that emission controls over regional scales substantially reduced PM levels. However, the bulk aerosol composition was relatively similar before and during APEC as a result of synergetic controls of aerosol precursors such as SO2, NOx, and volatile organic compounds (VOCs). In addition to emission controls, the routine

  8. Characteristics and sources of submicron aerosols above the urban canopy (260 m) in Beijing, China, during the 2014 APEC summit

    Science.gov (United States)

    Chen, C.; Sun, Y. L.; Xu, W. Q.; Du, W.; Zhou, L. B.; Han, T. T.; Wang, Q. Q.; Fu, P. Q.; Wang, Z. F.; Gao, Z. Q.; Zhang, Q.; Worsnop, D. R.

    2015-11-01

    The megacity of Beijing has experienced frequent severe fine particle pollution during the last decade. Although the sources and formation mechanisms of aerosol particles have been extensively investigated on the basis of ground measurements, real-time characterization of aerosol particle composition and sources above the urban canopy in Beijing is rare. In this study, we conducted real-time measurements of non-refractory submicron aerosol (NR-PM1) composition at 260 m at the Beijing 325 m meteorological tower (BMT) from 10 October to 12 November 2014, by using an aerosol chemical speciation monitor (ACSM) along with synchronous measurements of size-resolved NR-PM1 composition near ground level using a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). The NR-PM1 composition above the urban canopy was dominated by organics (46 %), followed by nitrate (27 %) and sulfate (13 %). The high contribution of nitrate and high NO3- / SO42- mass ratios illustrates an important role of nitrate in particulate matter (PM) pollution during the study period. The organic aerosol (OA) was mainly composed of secondary OA (SOA), accounting for 61 % on an average. Different from that measured at the ground site, primary OA (POA) correlated moderately with SOA, likely suggesting a high contribution from regional transport above the urban canopy. The Asia-Pacific Economic Cooperation (APEC) summit with strict emission controls provides a unique opportunity to study the impacts of emission controls on aerosol chemistry. All aerosol species were shown to have significant decreases of 40-80 % during APEC from those measured before APEC, suggesting that emission controls over regional scales substantially reduced PM levels. However, the bulk aerosol composition was relatively similar before and during APEC as a result of synergetic controls of aerosol precursors. In addition to emission controls, the routine circulations of mountain-valley breezes were also found to play

  9. A novel multi-level IC-compatible surface microfabrication technology for MEMS with independently controlled lateral and vertical submicron transduction gaps

    Science.gov (United States)

    Cicek, Paul-Vahe; Elsayed, Mohannad; Nabki, Frederic; El-Gamal, Mourad

    2017-11-01

    An above-IC compatible multi-level MEMS surface microfabrication technology based on a silicon carbide structural layer is presented. The fabrication process flow provides optimal electrostatic transduction by allowing the creation of independently controlled submicron vertical and lateral gaps without the need for high resolution lithography. Adopting silicon carbide as the structural material, the technology ensures material, chemical and thermal compatibility with modern semiconductor nodes, reporting the lowest peak processing temperature (i.e. 200 °C) of all comparable works. This makes this process ideally suited for integrating capacitive-based MEMS directly above standard CMOS substrates. Process flow design and optimization are presented in the context of bulk-mode disk resonators, devices that are shown to exhibit improved performance with respect to previous generation flexural beam resonators, and that represent relatively complex MEMS structures. The impact of impending improvements to the fabrication technology is discussed.

  10. Evaluation of traffic exhaust contributions to ambient carbonaceous submicron particulate matter in an urban roadside environment in Hong Kong

    Science.gov (United States)

    Lee, Berto Paul; Kwok Keung Louie, Peter; Luk, Connie; Keung Chan, Chak

    2017-12-01

    Road traffic has significant impacts on air quality particularly in densely urbanized and populated areas where vehicle emissions are a major local source of ambient particulate matter. Engine type (i.e., fuel use) significantly impacts the chemical characteristics of tailpipe emission, and thus the distribution of engine types in traffic impacts measured ambient concentrations. This study provides an estimation of the contribution of vehicles powered by different fuels (gasoline, diesel, LPG) to carbonaceous submicron aerosol mass (PM1) based on ambient aerosol mass spectrometer (AMS) and elemental carbon (EC) measurements and vehicle count data in an urban inner city environment in Hong Kong with the aim to gauge the importance of different engine types to particulate matter burdens in a typical urban street canyon. On an average per-vehicle basis, gasoline vehicles emitted 75 and 93 % more organics than diesel and LPG vehicles, respectively, while EC emissions from diesel vehicles were 45 % higher than those from gasoline vehicles. LPG vehicles showed no appreciable contributions to EC and thus overall represented a small contributor to traffic-related primary ambient PM1 despite their high abundance (˜ 30 %) in the traffic mix. Total carbonaceous particle mass contributions to ambient PM1 from diesel engines were only marginally higher (˜ 4 %) than those from gasoline engines, which is likely an effect of recently introduced control strategies targeted at commercial vehicles and buses. Overall, gasoline vehicles contributed 1.2 µg m-3 of EC and 1.1 µ m-3 of organics, LPG vehicles 0.6 µg m-3 of organics and diesel vehicles 2.0 µg m-3 of EC and 0.7 µg m-3 of organics to ambient carbonaceous PM1.

  11. Thymol-based submicron emulsions exhibit antifungal activity against Fusarium graminearum and inhibit Fusarium head blight in wheat.

    Science.gov (United States)

    Gill, T A; Li, J; Saenger, M; Scofield, S R

    2016-10-01

    Fusarium graminearum is a very destructive fungal pathogen that leads to Fusarium head blight (FHB) in wheat, a disease which costs growers millions of dollars annually both in crop losses and in remediation efforts. Current countermeasures include the deployment of wheat varieties with some resistance to FHB in conjunction with timed fungicide treatments. In this article, we introduce a fungicide based on thymol, a naturally occurring plant phenolic derived from essential oils. To overcome the hydrophobicity of thymol, the thymol active was incorporated into a low-surfactant submicron emulsion with and without a carrier oil. The minimum fungicidal concentration of F. graminearum was found to be both 0·02% for thymol emulsions with and without an oil component. Time-to-kill experiments showed that thymol emulsions were able to inactivate F. graminearum in as little as 10 s at concentrations above 0·06%. Spraying the thymol emulsions (~0·1% range) on the wheat variety Bobwhite demonstrated significant reductions in FHB infection rate (number of infected spikelets). However, with 0·5% thymol, the wheat heads exhibited premature senescence. Transmission and scanning electron micrographs suggest that the mechanism of antifungal action is membrane mediated, as conidia exposed to thymol showed complete organelle disorganization and evidence of lipid emulsification. The collective experimental data suggest that thymol emulsions may be an effective naturally derived alternative to the current thymol treatments, and chemical fungicides in ameliorating FHB. This is the first thymol-derived nanoemulsion particles resuspended into water and not DMSO, exhibiting the same antibacterial/antifungal activity as previously described thymol and thyme oil treatments. This drastically reduces the environmental footprint thymol will leave if utilized as a fungicide treatment on field crops. © 2016 The Society for Applied Microbiology.

  12. Evaluation of traffic exhaust contributions to ambient carbonaceous submicron particulate matter in an urban roadside environment in Hong Kong

    Directory of Open Access Journals (Sweden)

    B. P. Lee

    2017-12-01

    Full Text Available Road traffic has significant impacts on air quality particularly in densely urbanized and populated areas where vehicle emissions are a major local source of ambient particulate matter. Engine type (i.e., fuel use significantly impacts the chemical characteristics of tailpipe emission, and thus the distribution of engine types in traffic impacts measured ambient concentrations. This study provides an estimation of the contribution of vehicles powered by different fuels (gasoline, diesel, LPG to carbonaceous submicron aerosol mass (PM1 based on ambient aerosol mass spectrometer (AMS and elemental carbon (EC measurements and vehicle count data in an urban inner city environment in Hong Kong with the aim to gauge the importance of different engine types to particulate matter burdens in a typical urban street canyon. On an average per-vehicle basis, gasoline vehicles emitted 75 and 93 % more organics than diesel and LPG vehicles, respectively, while EC emissions from diesel vehicles were 45 % higher than those from gasoline vehicles. LPG vehicles showed no appreciable contributions to EC and thus overall represented a small contributor to traffic-related primary ambient PM1 despite their high abundance (∼ 30 % in the traffic mix. Total carbonaceous particle mass contributions to ambient PM1 from diesel engines were only marginally higher (∼ 4 % than those from gasoline engines, which is likely an effect of recently introduced control strategies targeted at commercial vehicles and buses. Overall, gasoline vehicles contributed 1.2 µg m−3 of EC and 1.1 µ m−3 of organics, LPG vehicles 0.6 µg m−3 of organics and diesel vehicles 2.0 µg m−3 of EC and 0.7 µg m−3 of organics to ambient carbonaceous PM1.

  13. Imaging of vaporised sub-micron phase change contrast agents with high frame rate ultrasound and optics.

    Science.gov (United States)

    Lin, Shengtao; Zhang, Ge; Jamburidze, Akaki; Chee, Melisse; Leow, Chee Hau; Garbin, Valeria; Tang, Meng-Xing

    2018-01-31

    Phase-change ultrasound contrast agent (PCCA), or nanodroplet shows promises as an alternative to conventional microbubble agent over a wide range of diagnostic applications. In the meantime, high-frame-rate (HFR) ultrasound imaging with microbubbles enables unprecedentedly temporal resolution compared to traditional contrast-enhanced ultrasound imaging. The combination of HFR ultrasound imaging and PCCAs can offer opportunities to observe and better understand PCCA behaviour after vaporisation capturing the fast phenomenon at a high temporal resolution. In this study, we utilised HFR ultrasound at frame rates in the kilohertz range (5-20 kHz) to image the native and size-selected PCCA populations immediately after vaporisation in vitro with clinical acoustic parameters. The size-selected PCCAs through filtration are shown to preserve submicron-sized (mean diameter < 200 nm) population without micron-sized outliers (> 1 µm) that are originally from the native PCCA emulsion. The results demonstrate imaging signals with different amplitude and temporal features compared to that of microbubbles. Compared with microbubbles, both B-mode and Pulse-Inversion (PI) signals from vaporised PCCA populations were reduced significantly in the first tens of milliseconds, while only B-mode signals from the PCCAs recovered during the next 400 ms, suggesting significant changes to the size distribution of PCCAs after vaporisation. It is also shown that such recovery in signal over time is not evident when using size-selective PCCAs. Furthermore, it was found that signals from the vaporised PCCA populations are affected by the amplitude and frame rate of the HFR ultrasound imaging. Using high-speed optical camera observation (30 kHz), we observed the particle size change in the vaporised PCCA populations exposed to the HFR ultrasound imaging pulses. These findings can benefit the understandings of PCCA behaviour under HFR ultrasound imaging. © 2018 Institute of Physics and

  14. Aerosol particles in the Mexican East Pacific Part I: processing and vertical redistribution by clouds

    Directory of Open Access Journals (Sweden)

    D. Baumgardner

    2005-01-01

    Full Text Available Airborne measurements of aerosol particle size distributions were made in the Mexican Intertropical Convergence Zone. The volume concentrations of submicron and super micron particles at cloud base were compared with those in near-cloud regions over a range of altitudes. Of 78 near-cloud regions analyzed, 68% and 45% had enhanced volumes of submicron particles and supermicron particles, respectively. In addition, 35% of these regions had supermicron particles removed, presumably by precipitation. In 61% of the cases the enhancement in volume occurred over the size range from 0.1 to 50 μm whereas only submicron volumes were enhanced in 35% of the cases. In regions near clouds that were formed in air of maritime origin the frequency of volume enhancement decreased with increasing altitude and was twice as frequent on the dissipating side of clouds compared to the growing side. No such differences were found in the regions near clouds formed in air originating from the land. The frequency and average magnitude of volume enhancement are in qualitative and quantitative agreement with previous observational and theoretical studies that relate enhancements in particle mass to the uptake by cloud droplets of SO2 accompanied by additional growth by droplet coalescence.

  15. Reactions Between Vapor Phase Lead Compounds and In Situ Generated Silica Particles at Various Lead-Silicon Feed Ratios: Applications to Toxic Metal Capture in Combustors.

    Science.gov (United States)

    Owens, Timothy M; Biswas, Pratim

    1996-06-01

    A detailed characterization was performed of the particles produced under various Pb:Si molar feed ratios for a maximum flow reactor temperature of 1000 °C. The silica particles formed in the high temperature region coagulated and only partially coalesced to form large agglomerate structures of high specific surface area. For a lead-only feed, the resulting particles were hydrocerussite with small but detectable amounts of massicot. As the silica precursor was inlet in excess amounts (Pb:Si crystalline lead compounds disappeared and amorphous lead-silica complexes dominated. The particle morphology also changed from cylindrical, polygonal, and spherical shapes to large agglomerate structures composed of several size modes of primary particles. At Pb:Si molar feed ratios of 1:12 and 1:29, the particles making up the chainlike agglomerate structure were primarily spherical, with larger lead silicate spherical particles (=0.5 |im) attached to the agglomerate. The lead was found to be distributed throughout the large agglomerate structures, implying easier capture of lead emissions in particulate control devices.

  16. X-ray Fluorescence Tomography of Aged Fluid-Catalytic-Cracking Catalyst Particles Reveals Insight into Metal Deposition Processes

    NARCIS (Netherlands)

    Kalirai, Samanbir; Boesenberg, Ulrike; Falkenberg, Gerald; Meirer, Florian; Weckhuysen, Bert M.

    2015-01-01

    Microprobe X-ray fluorescence tomography was used to investigate metal poison deposition in individual, intact and industrially deactivated fluid catalytic cracking (FCC) particles at two differing catalytic life-stages. 3D multi-element imaging, at submicron resolution was achieved by using a

  17. Submicron-resolution photoacoustic microscopy of endogenous light-absorbing biomolecules

    Science.gov (United States)

    Zhang, Chi

    Photoacoustic imaging in biomedicine has the unique advantage of probing endogenous light absorbers at various length scales with a 100% relative sensitivity. Among the several modalities of photoacoustic imaging, optical-resolution photoacoustic microscopy (OR-PAM) can achieve high spatial resolution, on the order of optical wavelength, at targets fluorescent markers, label-free PAM avoids the major concerns that the fluorescent labeling probes may disturb the function of biomolecules and may have an insufficient density. This dissertation aims to advance label-free OR-PAM to the subcellular scale. The first part of this dissertation describes the technological advancement of PAM yielding high spatial resolution in 3D. The lateral resolution was improved by using optical objectives with high numerical apertures for optical focusing. The axial resolution was improved by using broadband ultrasonic transducers for ultrasound detection. We achieved 220 nm lateral resolution in transmission mode, 0.43 microm lateral resolution in reflection mode, 7.6 microm axial resolution in normal tissue, and 5.8 microm axial resolution with silicone oil immersion/injection. The achieved lateral resolution and axial resolution were the finest reported at the time. With high-resolution in 3D, PAM was demonstrated to resolve cellular and subcellular structures in vivo, such as red blood cells and melanosomes in melanoma cells. Compared with previous PAM systems, our high-resolution PAM could resolve capillaries in mouse ears more clearly. As an example application, we demonstrated intracellular temperature imaging, assisted by fluorescence signal detection, with sub-degree temperature resolution and sub-micron lateral resolution. The second part of this dissertation describes the exploration of endogenous light-absorbing biomolecules for PAM. We demonstrated cytochromes and myoglobin as new absorption contrasts for PAM and identified the corresponding optimal wavelengths for imaging

  18. Optical Response to Submicron Digital Elements Simulated by FDTD Wavelets with Refractive Impulse

    Directory of Open Access Journals (Sweden)

    Antony J. Bourdillon

    2014-01-01

    Full Text Available Accurate simulation from digital, submicron, optical elements is obtained by finite difference time domain (FDTD results that are phase analyzed as sources for Huygens wavelets on fine scales much shorter than the wavelength used. Results, from the MIT electromagnetic evaluation program, are renormalized by a method here called “refractive impulse.” This is valid for polarized responses from digital diffractive and focusing optics. The method is employed with plane wave incidence at any angle or with diverging or converging beams. It is more systematic, more versatile, and more accurate than commercial substitutes.

  19. Reduced impact of induced gate noise on inductively degenerated LNAs in deep submicron CMOS technologies

    DEFF Research Database (Denmark)

    Rossi, P.; Svelto, F.; Mazzanti, A.

    2005-01-01

    Designers of radio-frequency inductively-degenerated CMOS low-noise-amplifiers have usually not followed the guidelines for achieving minimum noise figure. Nonetheless, state-of-the- art implementations display noise figure values very close to the theoretical minimum. In this paper, we point out...... that this is due to the effect of the parasitic overlap capacitances in the MOS device. In particular, we show that overlap capacitances lead to a significant induced-gate-noise reduction, especially when deep sub-micron CMOS processes are used....

  20. Note: Aligned deposition and modal characterization of micron and submicron poly(methyl methacyrlate) fiber cantilevers.

    Science.gov (United States)

    Nain, Amrinder S; Filiz, Sinan; Ozdoganlar, O Burak; Sitti, Metin; Amon, Cristina

    2010-01-01

    Polymeric micro-/nanofibers are finding increasing use as sensors for novel applications. Here, we demonstrate the ability to deposit an array of poly(methyl methacyrlate) fibers with micron and submicron diameters in aligned configurations on customized piezoelectric shakers. Using lateral motion of an atomic force microscope tip, fibers are broken to obtain fiber cantilevers of high aspect ratio (length/diameter > 20). The resonant frequencies of fabricated microfiber cantilevers are experimentally measured using a laser Doppler vibrometer. An average Young's modulus of 3.5 GPa and quality factor of 20 were estimated from the experimentally obtained frequency responses.

  1. Pressing Induced Polymorphic Phase Transition in Submicron-Sized Gamma-Hmx

    Science.gov (United States)

    Lee, K.-Y.; Moore, D. S.

    2007-12-01

    Using Raman spectroscopy, a novel submicron-sized HMX (sm-HMX) was determined to be both the gamma polymorph and stable with respect to conversion to beta-HMX under ambient conditions for at least a year. Pressing of sm-HMX powder in a small diameter pellet press at pressures from 10,000 psi to 31,000 psi and 1 to 5 minute hold times was found to promote the gamma to beta polymorphic phase transition. The fraction converted and rate of conversion versus time after pellet removal from the press, measured using Raman spectroscopy, fit a sigmoidal curve, indicating nucleation and growth as a possible polymorphic transition mechanism.

  2. Bloch-wave engineered submicron-diameter quantum-dot micropillars for cavity QED experiments

    DEFF Research Database (Denmark)

    Gregersen, Niels; Lermer, Matthias; Reitzenstein, Stephan

    2013-01-01

    The semiconductor micropillar is attractive for cavity QED experiments. For strong coupling, the figure of merit is proportional to Q/√V, and a design combining a high Q and a low mode volume V is thus desired. However, for the standard submicron diameter design, poor mode matching between the ca...... the cavity and the DBR Bloch mode limits the Q. We present a novel adiabatic design where Bloch-wave engineering is employed to improve the mode matching, allowing the demonstration of a record-high vacuum Rabi splitting of 85 μeV and a Q of 13600 for a 850 nm diameter micropillar....

  3. An Empirical Algorithm for Power Analysis in Deep Submicron Electronic Designs

    Directory of Open Access Journals (Sweden)

    May Huang

    2002-01-01

    Full Text Available An empirical algorithm applied to logic level power analysis in deep submicron VLSI designs is introduced in the paper. The method explores a static analysis strategy using unit functions to represent signal transitions. It can be extended to the use of a Register Transfer Level (RTL power analysis after RTL codes are translated to Boolean equations. A new method for representing state-dependent power models is also introduced in the paper to reduce the complexity of power modeling and to improve the performance of power analysis. The modeling method supports not only the empirical power analysis, but also general simulation-based power analysis methods.

  4. Dye-doped spherical particles of optical cavity structure

    Science.gov (United States)

    Shibata, Shuichi; Yano, Tetsuji; Yamane, Masayuki

    1997-10-01

    Preparation of micrometer-sized spherical particles containing Rhodamine 6G (R6G) has been investigated for spherical cavity structure. Hydrolysis and polymerization processes of phenyltriethoxysilane (PTES) as a starting material was pursued by observing the change of PTES/R6G in HCl solution with its optical absorption and viscosity. As the polymerization of PTES proceeded, increase of molecular size resulted in change its properties from hydrophilic to hydrophobic, and subsequently the solution separated into two layers of aqueous and organic. Polymerized PTES in the organic layer showed good affinity with incorporated R6G, and high monomer/dimer ratio in particles was achieved. Moreover, using them intermixing of unsuitable particles of submicron size was avoided, because hydrolyzed PTES of small molecular size that is the origin of submicron-sized particles was removed to the aqueous layer. With stirring, titration of diluted droplets containing polymerized PTES was suitable for preparing several micrometer sized particles, and followed by solidification in ammonia water. Degree of the polymerization of PTES and viscosity of liquid droplets were the key factors for determining the properties of R6G-doped spherical particles of optical cavity structure.

  5. Fine particle and trace element emission characterization from energy production and process industry; Energiantuotannon ja prosessiteollisuuden pienhiukkas- ja raskasmetallipaeaestoejen karakterisointi

    Energy Technology Data Exchange (ETDEWEB)

    Hokkinen, J.; Jokiniemi, J. [VTT Processes, Espoo (Finland); Aurela, M.; Hillamo, R. [Finnish Meteorological Inst. (Finland)

    2004-07-01

    ashes, bottom ashes and fly ash particles collected with BLPI and filters were analyzed with ICP-MS (Ion Coupled Plasma- Mass Spectroscopy) and IC (Ion Chromatography) or XRF (X-Ray fluorescence). For fluidized bed combustion the filter collection efficiency was 98.0% to 99.9% of the total particulate mass. In the fine particle mode (particle diameter 0.1-1.0 p.m) ESP had lower efficiency 90% to 99%, while fabric filter had better than 99% efficiency also for fine particles. The solid fuel combustion-generated particle emissions typically consist of two types of particles: fine particles approximately 0.1-1.0 im in diameter that are formed from the ash-forming species that are volatilized during combustion and residual ash particles larger than 1 im in diameter that are formed from mineral impurities in the fuels. In fluidized-bed combustion, also a third particle type is found that consists of fragmented bed material. The relative abundance of the different particle types depends on the fuel and combustion system as well as combustion conditions. Typically, for example, higher combustion temperature increases the amount of fine particles. Also, biomass combustion generally produces more fine particles than, for example, coal combustion due to the different mode of occurrence of the ash-forming compounds in the fuels. Many trace elements are relatively volatile during combustion and are consequently enriched in the fine particle fraction. In black liquor combustion the fine particle mode is at larger particles i.e. 1-3 im due to larger amount of volatilized material and hence mass concentration. In black liquor combustion the ESP efficiency is good also for fine particles. The measurements showed, that there is a relation between the fine particle mass concentration, the process temperature and Cl, S, K, Na, Pb, Cd, Cu and As concentrations in fuel. Higher process temperature and higher Chlorine content in fuel increase the concentration of these elements in submicron

  6. Concentrations and Sources of Airborne Particles in a Neonatal Intensive Care Unit.

    Directory of Open Access Journals (Sweden)

    Dusan Licina

    Full Text Available Premature infants in neonatal intensive care units (NICUs have underdeveloped immune systems, making them susceptible to adverse health consequences from air pollutant exposure. Little is known about the sources of indoor airborne particles that contribute to the exposure of premature infants in the NICU environment. In this study, we monitored the spatial and temporal variations of airborne particulate matter concentrations along with other indoor environmental parameters and human occupancy. The experiments were conducted over one year in a private-style NICU. The NICU was served by a central heating, ventilation and air-conditioning (HVAC system equipped with an economizer and a high-efficiency particle filtration system. The following parameters were measured continuously during weekdays with 1-min resolution: particles larger than 0.3 μm resolved into 6 size groups, CO2 level, dry-bulb temperature and relative humidity, and presence or absence of occupants. Altogether, over sixteen periods of a few weeks each, measurements were conducted in rooms occupied with premature infants. In parallel, a second monitoring station was operated in a nearby hallway or at the local nurses' station. The monitoring data suggest a strong link between indoor particle concentrations and human occupancy. Detected particle peaks from occupancy were clearly discernible among larger particles and imperceptible for submicron (0.3-1 μm particles. The mean indoor particle mass concentrations averaged across the size range 0.3-10 μm during occupied periods was 1.9 μg/m3, approximately 2.5 times the concentration during unoccupied periods (0.8 μg/m3. Contributions of within-room emissions to total PM10 mass in the baby rooms averaged 37-81%. Near-room indoor emissions and outdoor sources contributed 18-59% and 1-5%, respectively. Airborne particle levels in the size range 1-10 μm showed strong dependence on human activities, indicating the importance of indoor-generated

  7. Formation of fine particles in co-combustion of coal and solid recovered fuel in a pulverized coal-fired power station

    DEFF Research Database (Denmark)

    Wu, Hao; Pedersen, Anne Juul; Glarborg, Peter

    2011-01-01

    appear to be an important formation mechanism. The elemental composition of the particles from coal combustion showed that S and Ca were significantly enriched in ultrafine particles and P was also enriched considerably. However, compared with supermicron particles, the contents of Al, Si and K were...... showed an ultrafine mode centered at approximately 0.1 μm. Compared with coal combustion, co-combustion of coal and SRF increased the formation of submicron particles, especially ultrafine particles below 0.2 μm. The morphology of the particles indicated that supermicron particles were primarily formed...

  8. Particle Transport in Parallel-Plate Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rader, D.J.; Geller, A.S.

    1999-08-01

    A major cause of semiconductor yield degradation is contaminant particles that deposit on wafers while they reside in processing tools during integrated circuit manufacturing. This report presents numerical models for assessing particle transport and deposition in a parallel-plate geometry characteristic of a wide range of single-wafer processing tools: uniform downward flow exiting a perforated-plate showerhead separated by a gap from a circular wafer resting on a parallel susceptor. Particles are assumed to originate either upstream of the showerhead or from a specified position between the plates. The physical mechanisms controlling particle deposition and transport (inertia, diffusion, fluid drag, and external forces) are reviewed, with an emphasis on conditions encountered in semiconductor process tools (i.e., sub-atmospheric pressures and submicron particles). Isothermal flow is assumed, although small temperature differences are allowed to drive particle thermophoresis. Numerical solutions of the flow field are presented which agree with an analytic, creeping-flow expression for Re < 4. Deposition is quantified by use of a particle collection efficiency, which is defined as the fraction of particles in the reactor that deposit on the wafer. Analytic expressions for collection efficiency are presented for the limiting case where external forces control deposition (i.e., neglecting particle diffusion and inertia). Deposition from simultaneous particle diffusion and external forces is analyzed by an Eulerian formulation; for creeping flow and particles released from a planar trap, the analysis yields an analytic, integral expression for particle deposition based on process and particle properties. Deposition from simultaneous particle inertia and external forces is analyzed by a Lagrangian formulation, which can describe inertia-enhanced deposition resulting from particle acceleration in the showerhead. An approximate analytic expression is derived for particle

  9. Lunar surface phenomena - Solar flare track gradients, microcraters, and accretionary particles

    Science.gov (United States)

    Blanford, G. E.; Fruland, R. M.; Mckay, D. S.; Morrison, D. A.

    1974-01-01

    Data are presented concerning the energy spectra of solar flare particles and the distribution of particles producing submicron diameter craters. Processes which alter the albedo and possibly the chemistry of exposed lunar surfaces are also considered. Measurements are reported of solar flare track gradients in rock 64455 which is sufficiently young to have uneroded surfaces on its sides. Attention is also given to accretionary particles adhering to host surfaces, microcraters on soil particles, and microcraters on the oriented surfaces of sample 76015 from a boulder at Station 6 of the Apollo 17 site.

  10. Particles with similar LET values generate DNA breaks of different complexity and reparability: a high-resolution microscopy analysis of γH2AX/53BP1 foci.

    Science.gov (United States)

    Jezkova, Lucie; Zadneprianetc, Mariia; Kulikova, Elena; Smirnova, Elena; Bulanova, Tatiana; Depes, Daniel; Falkova, Iva; Boreyko, Alla; Krasavin, Evgeny; Davidkova, Marie; Kozubek, Stanislav; Valentova, Olga; Falk, Martin

    2018-01-18

    Biological effects of high-LET (linear energy transfer) radiation have received increasing attention, particularly in the context of more efficient radiotherapy and space exploration. Efficient cell killing by high-LET radiation depends on the physical ability of accelerated particles to generate complex DNA damage, which is largely mediated by LET. However, the characteristics of DNA damage and repair upon exposure to different particles with similar LET parameters remain unexplored. We employed high-resolution confocal microscopy to examine phosphorylated histone H2AX (γH2AX)/p53-binding protein 1 (53BP1) focus streaks at the microscale level, focusing on the complexity, spatiotemporal behaviour and repair of DNA double-strand breaks generated by boron and neon ions accelerated at similar LET values (∼135 keV μm-1) and low energies (8 and 47 MeV per n, respectively). Cells were irradiated using sharp-angle geometry and were spatially (3D) fixed to maximize the resolution of these analyses. Both high-LET radiation types generated highly complex γH2AX/53BP1 focus clusters with a larger size, increased irregularity and slower elimination than low-LET γ-rays. Surprisingly, neon ions produced even more complex γH2AX/53BP1 focus clusters than boron ions, consistent with DSB repair kinetics. Although the exposure of cells to γ-rays and boron ions eliminated a vast majority of foci (94% and 74%, respectively) within 24 h, 45% of the foci persisted in cells irradiated with neon. Our calculations suggest that the complexity of DSB damage critically depends on (increases with) the particle track core diameter. Thus, different particles with similar LET and energy may generate different types of DNA damage, which should be considered in future research.

  11. Laser smoothing of sub-micron grooves in hydroxyl-rich fused silica

    Energy Technology Data Exchange (ETDEWEB)

    Shen Nan [Lawrence Livermore National Laboratory, 7000 East Avenue, L-491, Livermore, CA 94550-9234 (United States); Matthews, Manyalibo J., E-mail: ibo@llnl.gov [Lawrence Livermore National Laboratory, 7000 East Avenue, L-491, Livermore, CA 94550-9234 (United States); Fair, James E.; Britten, Jerald A.; Nguyen, Hoang T.; Cooke, Diane; Elhadj, Selim; Yang, Steven T. [Lawrence Livermore National Laboratory, 7000 East Avenue, L-491, Livermore, CA 94550-9234 (United States)

    2010-04-01

    Nano- to micrometer-sized surface defects on UV-grade fused silica surfaces are known to be effectively smoothed through the use of high-temperature localized CO{sub 2} laser heating, thereby enhancing optical properties. However, the details of the mass transport and the effect of hydroxyl content on the laser smoothing of defective silica at sub-micron length scales are still not completely understood. In this study, we examine the morphological evolution of sub-micron, dry-etched periodic surface structures on type II and type III SiO{sub 2} substrates under 10.6 {mu}m CO{sub 2} laser irradiation using atomic force microscopy (AFM). In situ thermal imaging was used to map the transient temperature field across the heated region, allowing assessment of the T-dependent mass transport mechanisms under different laser-heating conditions. Computational fluid dynamics simulations correlated well with experimental results, and showed that for large effective capillary numbers (N{sub c} > 2), surface diffusion is negligible and smoothing is dictated by capillary action, despite the relatively small spatial scales studied here. Extracted viscosity values over 1700-2000 K were higher than the predicted bulk values, but were consistent with the surface depletion of OH groups, which was confirmed using confocal Raman microscopy.

  12. Single Mode ZnO Whispering-Gallery Submicron Cavity and Graphene Improved Lasing Performance.

    Science.gov (United States)

    Li, Jitao; Lin, Yi; Lu, Junfeng; Xu, Chunxiang; Wang, Yueyue; Shi, Zengliang; Dai, Jun

    2015-07-28

    Single-mode ultraviolet (UV) laser of ZnO is still in challenge so far, although it has been paid great attention along the past decades. In this work, single-mode lasing resonance was realized in a submicron-sized ZnO rod based on serially varying the dimension of the whispering-gallery mode (WGM) cavities. The lasing performance, such as the lasing quality factor (Q) and the lasing intensity, was remarkably improved by facilely covering monolayer graphene on the ZnO submicron-rod. The mode structure evolution from multimodes to single-mode was investigated systematically based on the total internal-wall reflection of the ZnO microcavities. Graphene-induced optical field confinement and lasing emission enhancement were revealed, indicating an energy coupling between graphene SP and ZnO exciton emission. This result demonstrated the response of graphene in the UV wavelength region and extended its potential applications besides many previous reports on the multifunctional graphene/semiconductor hybrid materials and devices in advanced electronics and optoelectronics areas.

  13. Laser smoothing of sub-micron grooves in hydroxyl-rich fused silica

    Energy Technology Data Exchange (ETDEWEB)

    Shen, N; Matthews, M J; Fair, J E; Britten, J A; Nguyen, H T; Cooke, D; Elhadj, S; Yang, S T

    2009-10-30

    Nano- to micrometer-sized surface defects on UV-grade fused silica surfaces are known to be effectively smoothed through the use of high-temperature localized CO{sub 2} laser heating, thereby enhancing optical properties. However, the details of the mass transport and the effect of hydroxyl content on the laser smoothing of defective silica at submicron length scales is still not completely understood. In this study, we examine the morphological evolution of sub-micron, dry-etched periodic surface structures on type II and type III SiO{sub 2} substrates under 10.6 {micro}m CO{sub 2} laser irradiation using atomic force microscopy (AFM). In-situ thermal imaging was used to map the transient temperature field across the heated region, allowing assessment of the T-dependent mass transport mechanisms under different laser-heating conditions. Computational fluid dynamics simulations correlated well with experimental results, and showed that for large effective capillary numbers (N{sub c} > 2), surface diffusion is negligible and smoothing is dictated by capillary action, despite the relatively small spatial scales studied here. Extracted viscosity values over 1700-2000K were higher than the predicted bulk values, but were consistent with the surface depletion of OH groups, which was confirmed using confocal Raman microscopy.

  14. Accurate submicron edge detection using the phase change of a nano-scale shifting laser spot

    Science.gov (United States)

    Hai, Hoang Hong; Chen, Liang-Chia; Nguyen, Duc Trung; Lin, Shyh-Tsong; Yeh, Sheng Lih; Yao, Ying

    2017-07-01

    Accurate edge detection with lateral super-resolution has been a critical issue in optical measurement because of the barrier imposed by the optical diffraction limit. In this study, a diffraction model that applies scalar diffraction theory of Fresnel-Kirchhoff is developed to simulate phase variance and distribution along edge location. Edge position is detected based on the phase variation that occurs on the edge with a surface step-height jump. To detect accurate edge positioning beyond the optical diffraction limit, a nanopositioning stage is used to scan the super steep edge of a single-edge and multi-edges submicron grating with nano-scale, and its phase distribution is captured. Model simulation is performed to confirm the phase-shifting phenomenon of the edge. A phase-shifting detection algorithm is developed to spatially detect the edge when a finite step scanning with a pitch of several tenth nanometers is used. A 180 nm deviation can occur during detection when the step height of the detecting edge varies, or the detecting laser spot covers more than one edge. Preliminary experimental results show that for the edge detection of the submicron line width of the grating, the standard deviation of the optical phase difference detection measurement is 38 nm. This technique provides a feasible means to achieve optical super-resolution on micro-grating measurement.

  15. Surfactant-assisted solvothermal synthesis of pure nickel submicron spheres with microwave-absorbing properties

    Science.gov (United States)

    Guo, Heng; Pu, Bingxue; Chen, Haiyuan; Yang, Jin; Zhou, Yajun; Yang, Jian; Bismark, Boateng; Li, Handong; Niu, Xiaobin

    2016-07-01

    Pure metallic nickel submicron spheres (Ni-SSs), flower-like nickel nanoflakes, and hollow micrometer-sized nickel spheres/tubes were controllably synthesized by a facile and efficient one-step solvothermal method with no reducing agent. The characteristics of these nickel nanostructures include morphology, structure, and purification. Possible synthesis mechanisms were discussed in detail. The resultant Ni-SSs had a wide diameter distribution of 200~800 nm through the aggregation of small nickel nanocrystals. The ferromagnetic behaviors of Ni-SSs investigated at room temperature showed high coercivity values. Furthermore, the microwave absorption properties of magnetic Ni-SSs were studied in the frequency range of 0.5-18.0 GHz. The minimum reflection loss reached -17.9 dB at 17.8 GHz with a thin absorption thickness of 1.2 mm, suggesting that the submicron spherical structures could exhibit excellent microwave absorption properties. More importantly, this one-pot synthesize route provides a universal and convenient way for preparation of larger scale pure Ni-SSs, showing excellent microwave absorption properties.

  16. Optimizing a manufacturing submicron CMOS process for low-voltage applications

    Science.gov (United States)

    Ma, Jun; Cheng, Sunny; Pryor, Bob; Klein, Kevin

    1996-09-01

    A low threshold voltage (Vt) is desired to improve a CMOS circuit performance when operating at reduced supply voltages to save power. In this paper, a practical approach to reduce Vt for a conventional, manufacturing submicron CMOS process is presented. This `evolutionary' approach to reduce Vt is taken so as the ensure manufacturability and to reduce process cost. This is found to be useful especially before a deep-submicron or a sophisticated process targeted for low voltage application becomes available and manufacturable. Vt reduction is achieved by the integration of a thinner, in the case presented here a 105 angstroms, gate oxide into a 0.65 micrometers process. The process is then optimized to provide the device with highest current-drive while obtaining lowest Vt with acceptable subthreshold leakage with conventional front-end and back-end process. It is shown that, with the minimal changes to the 0.65 micrometers conventional manufacturing process, the Vt's for nominal n- and p-channel devices can be reduced by 20% - 30%, with more than 1.5X improvement in current drive at 3.3 V compared to devices with 150 angstroms gate oxide. The enhancement of circuit performance is demonstrated with measurements of benchmark circuits including CPU, ROM, and FSRAM, where successful operation has been obtained near IV and operating frequencies are nearly doubled at supply voltage near 1.6 V compared to conventional 0.65 micrometers process.

  17. Single-Mode Lasers Based on Cesium Lead Halide Perovskite Submicron Spheres.

    Science.gov (United States)

    Tang, Bing; Dong, Hongxing; Sun, Liaoxin; Zheng, Weihao; Wang, Qi; Sun, Fangfang; Jiang, Xiongwei; Pan, Anlian; Zhang, Long

    2017-11-28

    Single-mode laser is realized in a cesium lead halide perovskite submicron sphere at room temperature. All-inorganic cesium lead halide (CsPbX 3 , X = Cl, Br, I) microspheres with tunable sizes (0.2-10 μm) are first fabricated by a dual-source chemical vapor deposition method. Due to smooth surface and regular geometry structure of microspheres, whispering gallery resonant modes make a single-mode laser realized in a submicron sphere. Surprisingly, a single-mode laser with a very narrow line width (∼0.09 nm) was achieved successfully in the CsPbX 3 spherical cavity at low threshold (∼0.42 μJ cm -2 ) with a high cavity quality factor (∼6100), which are the best specifications of lasing modes in all natural nano/microcavities ever reported. By modulating the halide composition and sizes of the microspheres, the wavelength of a single-mode laser can be continuously tuned from red to violet (425-715 nm). This work illustrates that the well-controlled synthesis of metal cesium lead halide perovskite nano/microspheres may offer an alternative route to produce a widely tunable and greatly miniaturized single-mode laser.

  18. Development of eco-friendly submicron emulsions stabilized by a bio-derived gum.

    Science.gov (United States)

    Pérez-Mosqueda, Luis María; Ramírez, Pablo; Trujillo-Cayado, Luis Alfonso; Santos, Jenifer; Muñoz, José

    2014-11-01

    Many traditional organic solvents are being gradually replaced by ecofriendly alternatives. D-Limonene is a terpenic (bio)-solvent that fulfils the requirements to be considered a green solvent. D-Limonene sub-micron emulsions suffer from Ostwald ripening destabilization. In this study, we examined the influence of the addition of a natural gum (rosin gum) to D-limonene in order to prevent Ostwald ripening. This contribution deals with the study of emulsions formulated with a mixture of D-limonene and rosin gum as dispersed phase and Pluronic PE9400 as emulsifier. The procedure followed for the development of these formulations was based on the application of product design principles. This led to the optimum ratio rosin gum/D-limonene and subsequently to the optimum surfactant concentration. The combination of different techniques (rheology, laser diffraction and multiple light scattering) was demonstrated to be a powerful tool to assist in the prediction of the emulsions destabilization process. Not only did the addition of rosin gum highly increase the stability of these emulsions by inhibiting the Ostwald ripening, but it also reduced the emulsions droplet size. Thus, we found that stable sub-micron D-limonene-in-water emulsions have been obtained in the range 3-6 wt% Pluronic PE-9400 by means of a single-step rotor/stator homogenizing process. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Effects of chemical composition and mixing state on size-resolved hygroscopicity and cloud condensation nuclei activity of submicron aerosols at a suburban site in northern Japan in summer

    Science.gov (United States)

    Müller, Astrid; Miyazaki, Yuzo; Aggarwal, Shankar G.; Kitamori, Yasuyuki; Boreddy, Suresh K. R.; Kawamura, Kimitaka

    2017-09-01

    Ambient hygroscopic properties, numbers of size-segregated cloud condensation nuclei (CCN) at different supersaturations (0.1%-0.8%), and the chemical composition of submicron particles were simultaneously measured at a suburban site in northern Japan in summer. Two distinct periods with different growth factors (GF), CCN activation diameters, and chemical compositions were observed. The data suggest that internally mixed sulfate aerosols dominated the accumulation size mode in relatively aged aerosols during the first period, whereas particles observed during the latter periods showed external mixing dominated by organics, which was linked to low hygroscopicity and CCN activity. In particular, the higher loading of water-soluble organic matter (WSOM; 60% of OM by mass) with increased WSOM/sulfate ratios corresponded to a low hygroscopicity parameter derived from the CCN measurement (κCCN = 0.15 ± 0.02) at a dry diameter (Ddry) of 146 nm. The results suggest that WSOM, likely dominated by the influence of biogenic sources, contributed to reducing the hygroscopicity and CCN activation at this particle size. Temporal variations in the number concentrations for low GF mode at Ddry = 49.6 nm were similar to those in the elemental carbon (EC) concentration, suggesting that EC contributed to reducing hygroscopicity at this smaller size. Our results suggest that chemical composition and mixing state are important factors controlling the hygroscopicity and CCN activation of submicron particles. These results provide useful data sets of size-resolved subsaturated and supersaturated hygroscopicity and highlight the importance of the abundance of OM relative to sulfate in predicting the effects on climate change.

  20. The generation of Turnip crinkle virus-like particles in plants by the transient expression of wild-type and modified forms of its coat protein

    Directory of Open Access Journals (Sweden)

    Keith eSaunders

    2015-12-01

    Full Text Available Turnip crinkle virus (TCV, a member of the genus carmovirus of the Tombusviridae family, has a genome consisting of a single positive-sense RNA molecule that is encapsidated in an icosahedral particle composed of 180 copies of a single type of coat protein. We have employed the CPMV-HT transient expression system to investigate the formation of TCV-like particles following the expression of the wild-type coat protein or modified forms of it that contain either deletions and/or additions insertions. Transient expression of the coat protein in plants results in the formation of capsid structures that morphologically resemble TCV virions (T=3 structure but encapsidate heterogeneous cellular RNAs, rather than the specific TCV coat protein messenger RNA. Expression of an amino-terminal deleted form of the coat protein resulted in the formation of smaller T=1 structures that are free of RNA. The possibility of utilising TCV as a carrier for the presentation of foreign proteins on the particle surface was also explored by fusing the sequence of GFP to the C-terminus of the coat protein. The expression of coat protein-GFP hybrids permitted the formation of VLPs but the yield of particles is diminished compared to the yield obtained with unmodified coat protein. Our results confirm the importance of the N-terminus of the coat protein for the encapsidation of RNA and show that the coat protein’s exterior P domain plays a key role in particle formation.

  1. submitter Next generation multi-scale biophysical characterization of high precision cancer particle radiotherapy using clinical proton, helium-, carbon- and oxygen ion beams

    CERN Document Server

    Dokic, Ivana; Niklas, Martin; Zimmermann, Ferdinand; Chaudhri, Naved; Krunic, Damir; Tessonnier, Thomas; Ferrari, Alfredo; Parodi, Katia; Jäkel, Oliver; Debus, Jürgen; Haberer, Thomas; Abdollahi, Amir

    2016-01-01

    The growing number of particle therapy facilities worldwide landmarks a novel era of precision oncology. Implementation of robust biophysical readouts is urgently needed to assess the efficacy of different radiation qualities. This is the first report on biophysical evaluation of Monte Carlo simulated predictive models of prescribed dose for four particle qualities i.e., proton, helium-, carbon- or oxygen ions using raster-scanning technology and clinical therapy settings at HIT. A high level of agreement was found between the in silico simulations, the physical dosimetry and the clonogenic tumor cell survival. The cell fluorescence ion track hybrid detector (Cell-Fit-HD) technology was employed to detect particle traverse per cell nucleus. Across a panel of radiobiological surrogates studied such as late ROS accumulation and apoptosis (caspase 3/7 activation), the relative biological effectiveness (RBE) chiefly correlated with the radiation species-specific spatio-temporal pattern of DNA double strand break ...

  2. Effect of silica particle size on macrophage inflammatory responses.

    Directory of Open Access Journals (Sweden)

    Toshimasa Kusaka

    Full Text Available Amorphous silica particles, such as nanoparticles (<100 nm diameter particles, are used in a wide variety of products, including pharmaceuticals, paints, cosmetics, and food. Nevertheless, the immunotoxicity of these particles and the relationship between silica particle size and pro-inflammatory activity are not fully understood. In this study, we addressed the relationship between the size of amorphous silica (particle dose, diameter, number, and surface area and the inflammatory activity (macrophage phagocytosis, inflammasome activation, IL-1β secretion, cell death and lung inflammation. Irrespective of diameter size, silica particles were efficiently internalized by mouse bone marrow-derived macrophages via an actin cytoskeleton-dependent pathway, and induced caspase-1, but not caspase-11, activation. Of note, 30 nm-1000 nm diameter silica particles induced lysosomal destabilization, cell death, and IL-1β secretion at markedly higher levels than did 3000 nm-10000 nm silica particles. Consistent with in vitro results, intra-tracheal administration of 30 nm silica particles into mice caused more severe lung inflammation than that of 3000 nm silica particles, as assessed by measurement of pro-inflammatory cytokines and neutrophil infiltration in bronchoalveolar lavage fluid of mice, and by the micro-computed tomography analysis. Taken together, these results suggest that silica particle size impacts immune responses, with submicron amorphous silica particles inducing higher inflammatory responses than silica particles over 1000 nm in size, which is ascribed not only to their ability to induce caspase-1 activation but also to their cytotoxicity.

  3. Polygamous particles

    OpenAIRE

    Wu, Kun-Ta; Feng, Lang; Sha, Ruojie; Dreyfus, Rémi; Grosberg, Alexander Y.; Seeman, Nadrian C.; Chaikin, Paul M.

    2012-01-01

    DNA is increasingly used as an important tool in programming the self-assembly of micrometer- and nanometer-scale particles. This is largely due to the highly specific thermoreversible interaction of cDNA strands, which, when placed on different particles, have been used to bind precise pairs in aggregates and crystals. However, DNA functionalized particles will only reach their true potential for particle assembly when each particle can address and bind to many different kinds of particles. ...

  4. Characterization of Damage to Bacteria and Bio-macromolecules Caused by (V)UV Radiation and Particles Generated by a Microscale Atmospheric Pressure Plasma Jet

    Science.gov (United States)

    Lackmann, Jan-Wilm; Schneider, Simon; Narberhaus, Franz; Benedikt, Jan; Bandow, Julia E.

    Atmospheric pressure plasma jets effectively inactivate bacteria on ­surfaces including infected tissues. This is due to the combined effects of (V)UV radiation, reactive oxygen and nitrogen species, ions, and high electric fields. A well-characterized microscale atmospheric pressure plasma jet (μ-APPJ) operated with He/O2 gas mixture has been modified so that (V)UV radiation and heavy reactive particles (mainly O3 molecules and O atoms) emitted from the plasma source can be separated effectively. The separation is achieved by an additional lateral He flow, which diverts the heavy particles from the jet axis. The new jet geometry is called X-Jet. Separation of different plasma components allows studying their effects on living cells and bio-macromolecules separately. First, the effectiveness of the separation of different plasma components was demonstrated by treatment of monolayers of ve