WorldWideScience

Sample records for styrene-butadiene rubber industry

  1. Application of Lignin as Antioxidant in Styrene Butadiene Rubber Composite

    Science.gov (United States)

    Liu, Shusheng; Cheng, Xiansu

    2010-11-01

    Lignin isolated from enzymatic hydrolyzed cornstalks (EHL) is a renewable natural polymer, and rubber is one of the most important polymer materials. The application of EHL in rubber industry is of great significance. The influence of EHL and antioxidant RD on the vulcanizing characteristics, thermal oxidative aging stability under free condition, and water extraction resistance of styrene-butadiene rubber (SBR) were investigated. The effect of EHL/antioxidant D composite antioxidant on the thermal oxidative ageing of SBR was also evaluated. Results showed that the protection of SBR from thermal oxidative aging by EHL/antioxidant D composite antioxidant was superior to that of antioxidant D. This is because EHL molecules have hindered phenol group and have excellent auxiliary antioxidant role with antioxidant D. Moreover, the influence of EHL on the vulcanizing characteristics of SBR compounds was better than that of antioxidant RD, and EHL can reduce the cure rate and increase the optimum cure time. It is because that the EHL molecules have hindered phenol group and methoxy group, which can form a special structure to capture free radical and terminate the chain reaction. The retained tensile strength of SBR compounds with EHL was similar to that of the samples with antioxidant RD, while the retained elongation at break of SBR compounds with EHL was higher than that of the samples with antioxidant RD. In addition, the SBR compounds with EHL have a good water extraction resistance property, which was similar to the samples with antioxidant RD. This is because EHL have large molecular weight, good stability and low solubility in water. In conclusion, due to the low price, abundant resources, non-toxic and pollution-free, etc., EHL will have broad application prospect.

  2. 40 CFR 63.500 - Back-end process provisions-carbon disulfide limitations for styrene butadiene rubber by emulsion...

    Science.gov (United States)

    2010-07-01

    ... disulfide limitations for styrene butadiene rubber by emulsion processes. 63.500 Section 63.500 Protection... limitations for styrene butadiene rubber by emulsion processes. (a) Owners or operators of sources subject to this subpart producing styrene butadiene rubber using an emulsion process shall operate the process...

  3. Particle reinforced composites from acrylamide modified blend of styrene-butadiene and natural rubber

    Science.gov (United States)

    Blends of styrene-butadiene rubber and natural rubber that provide balanced properties were modified with acrylamide and reinforced with soy protein particles. The rubber composites show improved mechanical properties. Both modified rubber and composites showed a faster curing rate. The crosslinking...

  4. Prediction of the Styrene Butadiene Rubber Performance by Emulsion Polymerization Using Backpropagation Neural Network

    Directory of Open Access Journals (Sweden)

    Yan-jiang Jin

    2013-01-01

    Full Text Available The effect of the amounts of initiator, emulsifier, and molecular weight regulator on the styrene butadiene rubber performance was investigated, based on the industrial original formula. It was found that the polymerization rate was increased with the increased dosage of initiator and emulsifier, and together with replenishing molecular weight regulator will make the Mooney viscosity of rubber meet the national standard when the conversion rate reaches 70%. The backpropagation neural network was trained by the original formula and ameliorated formula on the basis of Levenberg-Marquardt algorithm, and the relative error between the simulation results and experimental data is less than 1%. The good consistency shows that the BP neural network could predict the product performances in different formula conditions. It would pave the way for adjustment of the SBR formulation and prediction of the product performances.

  5. Microstructural analysis of carbon nanomaterials produced from pyrolysis/combustion of Styrene-Butadiene-Rubber (SBR)

    OpenAIRE

    Alves, Joner Oliveira; Zhuo, Chuanwei; Levendis, Yiannis Angelo; Tenório, Jorge Alberto Soares

    2011-01-01

    Styrene-Butadiene-Rubber (SBR) is a synthetic rubber copolymer used to fabricate several products. This study aims to demonstrate the use of SBR as feedstock for carbon nanomaterials (nanofibers and nanotubes) growth, and therefore to establish a novel process for destination of waste products containing SBR. A three stage electrically heated flow reactor was used. Small pellets of rubber were pyrolyzed at a temperature of 1000 ºC. The pyrolyzates were mixed with oxygen-containing gases and w...

  6. Polybutadiene and Styrene-Butadiene rubbers for high-dose dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Lucas N. [Instituto Federal de Educacao, Ciencia e Tecnologia de Goias-IFG,Campus Goiania, Goiania -GO (Brazil); Instituto de Pesquisas Energeticas e Nucleares -IPEN, Sao Paulo-SP (Brazil); Vieira, Silvio L. [Instituto de Fisica, Universidade Federal de Goias-UFG, Campus Samambaia, Goiania-GO (Brazil); Schimidt, Fernando [Instituto Federal de Educacao, Ciencia e Tecnologia de Goias-IFG,Campus Inhumas, Inhumas-GO (Brazil); Antonio, Patricia L.; Caldas, Linda V.E. [Instituto de Pesquisas Energeticas e Nucleares -IPEN, Sao Paulo-SP (Brazil)

    2015-07-01

    Polybutadiene and Styrene-Butadiene are synthetical rubbers used widely for pneumatic tires manufacturing. In this research, the dosimeter characteristics of those rubbers were studied for application in high-dose dosimetry. The rubber samples were irradiated with doses of 10 Gy up to 10 kGy, using a {sup 60}Co Gamma Cell-220 system (dose rate of 1.089 kGy/h) and their readings were taken on a Fourier Transform Infrared Spectroscopy-FTIR system (model Frontier/Perkin Elmer). The ratios of two absorbance peaks were taken for each kind of rubber spectrum, Polybutadiene (1306/1130 cm{sup -1}) and Styrene-Butadiene (1449/1306 cm{sup -1}). The ratio calculated was used as the response to the irradiation, and is not uniform across the sample. From the results, it can be concluded for both rubbers: a) the dose-response curves may be useful for high-dose dosimetry (greater than 250 Gy); b) their response for reproducibility presented standard deviations lower than 2.5%; c) the relative sensitivity was higher for Styrene-Butadiene (1.86 kGy{sup -1}) than for Polybutadiene (1.81 kGy{sup -1}), d) for doses of 10 kGy to 200 kGy, there was no variation in the dosimetric response. Both types of rubber samples showed usefulness as high-dose dosimeters. (authors)

  7. Performance Analysis of Styrene Butadiene Rubber-Latex on Cement Concrete Mixes.

    OpenAIRE

    Er. Kapil Soni; Dr. Y.P Joshi

    2014-01-01

    To improve the performance of concrete, polymers are mixed with concrete. It has been observed that polymer-modified concrete (PMC) is more durable than conventional concrete due to superior strength and high durability. In this research, effect of Styrene-Butadiene Rubber (SBR) latex on compressive strength and flexural strength of concrete has been studied and also the optimum polymer (SBR-Latex) content for concrete is calculated. This research was carried out to establish t...

  8. Effect of gamma irradiation on the properties of natural rubber/styrene butadiene rubber blends

    Directory of Open Access Journals (Sweden)

    A.B. Moustafa

    2016-09-01

    Full Text Available Blends of natural rubber (NR with styrene butadiene rubber (SBR with varying ratios have been prepared. Vulcanization of the prepared blends has been induced by irradiation of gamma rays with varying doses up to 250 kGy. Mechanical properties, namely tensile strength, tensile modulus at 100% elongation, elongation at break have been followed up as a function of irradiation dose as well as blend composition. Physical properties, namely gel fraction and swelling number have been followed up using benzene as a solvent. Thermal measurements namely thermogravimetric analysis were carried out. The results indicated that the addition of NR has improved the properties of NR / SBR blends. Also NR/SBR blend is thermally stable than NR alone.

  9. The use of styrene-butadiene rubber waste as a potential filler in nitrile rubber: order of addition and size of waste particles

    OpenAIRE

    Baeta,D. A.; Zattera,J. A.; Oliveira,M. G.; Oliveira,P. J.

    2009-01-01

    Styrene-butadiene rubber (SBR) has large applications in the shoe industry, especially as expanded sheets used to produce insoles and inner soles. According to TG analysis, the rubber content in SBR residues (SBR-r) was found to be around 26-wt%. Based on that data, a cost-effective technique for the reuse of SBR-r in Nitrile rubber (NBR) was developed. Later, the effect of SBR-r on the cure behavior, mechanical performance, swelling, and crosslink density of reused rubber was investigated, w...

  10. About the cure kinetics in natural rubber/styrene Butadiene rubber blends at 433 K

    Energy Technology Data Exchange (ETDEWEB)

    Mansilla, M.A., E-mail: mmansilla@df.uba.ar [Laboratorio de Polimeros y Materiales Compuestos, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon 1, C1428EGA Buenos Aires (Argentina); Marzocca, A.J. [Laboratorio de Polimeros y Materiales Compuestos, Departamento de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon 1, C1428EGA Buenos Aires (Argentina)

    2012-08-15

    Vulcanized blends of elastomers are employed in several goods mainly to improve physical properties and reduce costs. One of the most used blends of this kind is that composed by natural rubber (NR) and styrene butadiene rubber (SBR). The cure kinetic of these blends depends mainly on the compound formulation and the cure temperature and time. The preparation method of the blends can influence the mechanical properties of the vulcanized compounds. In this work the cure kinetic at 433 K of NR/SBR blends vulcanized with the system sulfur/TBBS (N-t-butyl-2-benzothiazole sulfenamide) is analyzed in samples prepared by mechanical mixing and solution blending. The two methods produce elastomer domains of NR and SBR, which present different microstructure due to the cure level attained during vulcanization. The cure kinetics is studied by means of rheometer tests and the model proposed by Kamal and Sourour. The analysis of the cure rate is presented and is related to the structure obtained during the vulcanization process.

  11. Morphological and mechanical properties of styrene butadiene rubber/nano copper nanocomposites

    Directory of Open Access Journals (Sweden)

    Maryam Hadizadeh Harandi

    Full Text Available In this research, rubber based nanocomposites with presence of nanoparticle has been studied. Styrene butadiene rubber (SBR/nanocopper (NC composites were prepared using two-roll mill method. Transmission electron microscope (TEM and scanning electron microscope (SEM images showed proper dispersion of NC in the SBR matrix without substantial agglomeration of nanoparticles. To evaluate the curing properties of nanocomposite samples, swelling and cure rheometric tests were conducted. Moreover, the rheological studies were carried out over a range of shear rates. The effect of NC particles was examined on the thermal behavior of the SBR using thermal gravimetric analysis (TGA. Furthermore, tensile tests were employed to investigate the capability of nanoparticles to enhance mechanical behavior of the compounds. The results showed enhancement in tensile properties with incorporation of NC to SBR matrix. Moreover, addition of NC increased shear viscosity and curing time of SBR composites. Keywords: Nanocopper, Rubber, Curing behavior, Rheological properties, Thermal stability, Tensile characteristics

  12. Microstructural analysis of carbon nanotubes produced from pyrolysis/combustion of styrene-butadiene rubber

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Joner O.; Zhuo, Chuanwei; Levendis, Yannis A. [Northeastern Univ., Boston, MA (United States). Coll. of Engineering. Dept. of Mechanical and Industrial Engineering; Tenorio, Jorge A.S. [University of Sao Paulo (USP), SP (Brazil). Polytechnic School. Dept. of Metallurgical and Materials Engineering

    2010-07-01

    Styrene-Butadiene-Rubber (SBR) is a synthetic rubber copolymer used to fabricate several products. This study aims to demonstrate the use of SBR as feedstock for carbon nanotubes (CNTs) growth, and therefore to establish a novel process for destination for wastes produced from SBR. Pellets of this rubber were controlled burned at temperature of 1000 deg C, and a catalyst system was used to synthesize the nanomaterials. CNTs are materials with a wide range of potential applications due to their extraordinary mechanical, thermal and electrical properties. Produced materials were characterized by SEM and TEM, and the hydrocarbons emissions were measured using GC. Results showed that materials with diameters of 30-100 nm and lengths of about 30 {mu}m were formed. That materials presented similar structures of multi-walled CNTs. Therefore, the use of SBR to produce carbon nanotubes showed quite satisfactory and an interesting field for future investments. (author)

  13. Fracture morphologies of carbon-black-loaded SBR (styrene-butadiene rubber) subjected to low-cycle, high-stress fatigue. [Styrene-butadiene rubber

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A.; Lesuer, D.R.; Patt, J.

    1988-02-01

    Experimental results, together with an analytical model, related to the loss in tensile strength of styrene-butadiene rubber (SBR) loaded with carbon black (CB) that had been subjected to low-cycle, high-stress fatigue tests were presented in a prior paper. The drop in tensile strength relative to that of a virgin sample was considered to be a measure of damage induced during the fatigue test. The present paper is a continuation of this study dealing with the morphological interpretations of the fractured surfaces, whereby the cyclic-tearing behavior, resulting in the damage, is related to the test and material parameters. It was found that failure is almost always initiated in the bulk of a sample at a material flaw. The size and definition of a flaw increase with an increase in carbon-black loading. Initiation flaw sites are enveloped by fan-shaped or penny-shaped regions which develop during cycling. The size and morphology of a fatigue-tear region appears to be independent of the fatigue load or the extent of the damage (strength loss). By contrast, either an increase in cycling load or an increase in damage at constant load increases the definition of the fatigue-region morphology for all formulations of carbon-black. On the finest scale, the morphology can be described in terms of tearing of individual groups of rubber strands, collapsing to form a cell-like structure. 18 refs., 13 figs.

  14. Organic Semiconducting Materials in Film and Powder Forms from a Co-polymeric Elastomer-Styrene Butadiene Rubber

    Science.gov (United States)

    Santhamma, G.; Predeep, P.

    2008-04-01

    Semiconducting materials in both film and powder forms are prepared by Antimony Pentachloride (SBCl5) doping in Styrene Butadiene Rubber (SBR). SBR is a synthetic co-polymeric elastomer, insulating in undoped state, is mainly used for manufacturing tires, tubes etc. Synthesized conducting materials are proposed to have tremendous application potentials in optoelectronic, electronic and electrical industries. For example conducting films can be used as active elements for fabrication of organic light emitting diodes, photovoltaic cells etc. Electrical and optical properties of prepared samples are studied by measuring electrical conductivity and analyzing spectroscopic data. Electrical conductivity of samples lies in the range of that of semi-conducting materials. Presence of conjugated sequences in the back bone of prepared conducting materials, which is regarded as pre-requisite condition for a polymer to conductive, is confirmed by studying UV/Vis spectra.

  15. Thermal Stability and Flammability of Styrene-Butadiene Rubber-Based (SBR) Ceramifiable Composites

    National Research Council Canada - National Science Library

    Anyszka, Rafał; Bieliński, Dariusz; Pędzich, Zbigniew; Rybiński, Przemysław; Imiela, Mateusz; Siciński, Mariusz; Zarzecka-Napierała, Magdalena; Gozdek, Tomasz; Rutkowski, Paweł

    2016-01-01

    Ceramifiable styrene-butadiene (SBR)-based composites containing low-softening-point-temperature glassy frit promoting ceramification, precipitated silica, one of four thermally stable refractory fillers...

  16. Biodegradation behavior of styrene butadiene rubber (SBR) reinforced with modified coconut shell powder

    Science.gov (United States)

    Sreejith, M. P.; Balan, Aparna K.; Shaniba, V.; Jinitha, T. V.; Subair, N.; Purushothaman, E.

    2017-06-01

    Biodegradation behavior of styrene butadiene rubber composites reinforced with natural filler, coconut shell powder (CSP), with different filler loadings were carried out under soil burial conditions for three to six months. The extent of biodegradation of the composites was evaluated through weight loss, tensile strength and hardness measurements. It was observed that the permanence of the composites was remarkably dependent on filler modification, size of the filler particle and filler content. Composites containing silane modified filler were found to be more resistant to attack by the microbes present in the soil. Mechanical properties such as tensile strength, Young's modulus and hardness were decreased after soil burial testing due to the microbial attack onto the samples.

  17. Performance of asphaltic concrete incorporating styrene butadiene rubber subjected to varying aging condition

    Science.gov (United States)

    Salah, Faisal Mohammed; Jaya, Ramadhansyah Putra; Mohamed, Azman; Hassan, Norhidayah Abdul; Rosni, Nurul Najihah Mad; Mohamed, Abdullahi Ali; Agussabti

    2017-12-01

    The influence of styrene butadiene rubber (SBR) on asphaltic concrete properties at different aging conditions was presented in this study. These aging conditions were named as un-aged, short-term, and long-term aging. The conventional asphalt binder of penetration grade 60/70 was used in this work. Four different levels of SBR addition were employed (i.e., 0 %, 1 %, 3 %, and 5 % by binder weight). Asphalt concrete mixes were prepared at selected optimum asphalt content (5 %). The performance was evaluated based on Marshall Stability, resilient modulus, and dynamic creep tests. Results indicated the improving stability and permanent deformation characteristics that the mixes modified with SBR polymer have under aging conditions. The result also showed that the stability, resilient modulus, and dynamic creep tests have the highest rates compared to the short-term aging and un-aged samples. Thus, the use of 5 % SBR can produce more durable asphalt concrete mixtures with better serviceability.

  18. Devulcanization of styrene butadiene rubber by microwave energy: Effect of the presence of ionic liquid

    Directory of Open Access Journals (Sweden)

    S. Seghar

    2015-12-01

    Full Text Available In this study, styrene butadiene rubber (SBR was devulcanized using microwave irradiation. In particular, effect of ionic liquid (IL, pyrrolidinium hydrogen sulfate [Pyrr][HSO4], on the devulcanization performance was studied. It was observed that the evolution of the temperature reached by rubber powder exposed to microwave irradiation for different energy values was favored by the presence of ionic liquid [Pyrr][HSO4] significantly over the whole range of the microwave energy values. Beyond the threshold point of 220 Wh/kg, the soluble fraction after devulcanization sharply increased with increasing devulcanization microwave energy. For the powder mixed with [Pyrr][HSO4], the increase was more significant. Furthermore, the crosslink density was observed to decrease slowly with the microwave energy up to 220 Wh/kg, beyond which the crosslink density decreased significantly for the rubber impregnated with IL. For the rubber with IL, significant and continuous increase in Tg with microwave energy values was observed in comparison with the SBR where no change in transition temperature was observed. Mechanical shearing of rubber gums in the two-roll mill favored the devulcanization process, which indicated that the combination of mechanical loading with microwave energy and IL is an efficient procedure allowing an optimal devulcanization of rubbers.

  19. Microstructural analysis of carbon nanomaterials produced from pyrolysis/combustion of Styrene-Butadiene-Rubber (SBR

    Directory of Open Access Journals (Sweden)

    Joner Oliveira Alves

    2011-12-01

    Full Text Available Styrene-Butadiene-Rubber (SBR is a synthetic rubber copolymer used to fabricate several products. This study aims to demonstrate the use of SBR as feedstock for carbon nanomaterials (nanofibers and nanotubes growth, and therefore to establish a novel process for destination of waste products containing SBR. A three stage electrically heated flow reactor was used. Small pellets of rubber were pyrolyzed at a temperature of 1000 ºC. The pyrolyzates were mixed with oxygen-containing gases and were burned. The products of combustion were used to synthesize the carbon nanomaterials (CNMs at the presence of a catalyst. CNMs have a wide range of potential applications due to their extraordinary mechanical, thermal and electrical properties. Produced materials were characterized by SEM and TEM, whereas combustion products were assessed using GC. Results showed that CNMs with outer diameters of 30-100 nm and lengths of about 30 µm were formed. Therefore, it was demonstrated that waste products containing SBR can be used to generate CNMs which are value-added products of intense technological interest.

  20. Styrene-butadiene rubber/halloysite nanotubes nanocomposites modified by methacrylic acid

    Energy Technology Data Exchange (ETDEWEB)

    Guo Baochun [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China)], E-mail: psbcguo@scut.edu.cn; Lei Yanda; Chen Feng; Liu Xiaoliang; Du Mingliang; Jia Demin [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China)

    2008-12-30

    Methacrylic acid (MAA) was used to improve the performance of styrene-butadiene rubber (SBR)/halloysite nanotubes (HNTs) nanocomposites by direct blending. The detailed interaction mechanisms of MAA and the in situ formed zinc methacrylate (ZDMA) were revealed by X-ray diffraction (XRD), surface area and porosity analysis, X-ray photoelectron spectroscopy (XPS) together with crosslink density determination. The strong interfacial bonding between HNTs and rubber matrix is resulted through ZDMA and MAA intermediated linkages. ZDMA connects SBR and HNTs via grafting/complexation mechanism. MAA bonds SBR and HNTs through grafting/hydrogen bonding mechanism. Significantly improved dispersion of HNTs in virtue of the interactions between HNTs and MAA or ZDMA was achieved. Effects of MAA content on the vulcanization behavior, morphology and mechanical properties of the nanocomposites were investigated. Promising mechanical properties of MAA modified SBR/HNTs nanocomposites were obtained. The changes in vulcanization behavior, mechanical properties and morphology were correlated with the interactions between HNTs and MAA or ZDMA and the largely improved dispersion of HNTs.

  1. Styrene-butadiene rubber/halloysite nanotubes nanocomposites modified by sorbic acid

    Energy Technology Data Exchange (ETDEWEB)

    Guo Baochun, E-mail: psbcguo@scut.edu.cn [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China); Chen Feng; Lei Yanda; Liu Xiaoliang; Wan Jingjing; Jia Demin [Department of Polymer Materials and Engineering, South China University of Technology, Guangzhou 510640 (China)

    2009-05-30

    Sorbic acid (SA) was used to improve the performance of styrene-butadiene rubber (SBR)/halloysite nanotubes (HNTs) nanocomposites by direct blending. The detailed mechanisms for the largely improved performance were studied by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), porosity analysis and crosslink density determination. The strong interfacial bonding between HNTs and rubber matrix is resulted through SA intermediated linkages. SA bonds SBR and HNTs through grafting copolymerization/hydrogen bonding mechanism. Significantly improved dispersion of HNTs in virtue of the interactions between HNTs and SA was achieved. Formation of zinc disorbate (ZDS) was revealed during the vulcanization of the composites. However, in the present systems, the contribution of ZDS to the reinforcement was limited. Effects of SA content on the vulcanization behavior, morphology and mechanical properties of the nanocomposites were investigated. Promising mechanical properties of SA modified SBR/HNTs nanocomposites were obtained. The changes in vulcanization behavior, mechanical properties and morphology were correlated with the interactions between HNTs and SA and the largely improved dispersion of HNTs.

  2. Styrene-butadiene rubber/halloysite nanotubes nanocomposites modified by sorbic acid

    Science.gov (United States)

    Guo, Baochun; Chen, Feng; Lei, Yanda; Liu, Xiaoliang; Wan, Jingjing; Jia, Demin

    2009-05-01

    Sorbic acid (SA) was used to improve the performance of styrene-butadiene rubber (SBR)/halloysite nanotubes (HNTs) nanocomposites by direct blending. The detailed mechanisms for the largely improved performance were studied by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), differential scanning calorimetry (DSC), porosity analysis and crosslink density determination. The strong interfacial bonding between HNTs and rubber matrix is resulted through SA intermediated linkages. SA bonds SBR and HNTs through grafting copolymerization/hydrogen bonding mechanism. Significantly improved dispersion of HNTs in virtue of the interactions between HNTs and SA was achieved. Formation of zinc disorbate (ZDS) was revealed during the vulcanization of the composites. However, in the present systems, the contribution of ZDS to the reinforcement was limited. Effects of SA content on the vulcanization behavior, morphology and mechanical properties of the nanocomposites were investigated. Promising mechanical properties of SA modified SBR/HNTs nanocomposites were obtained. The changes in vulcanization behavior, mechanical properties and morphology were correlated with the interactions between HNTs and SA and the largely improved dispersion of HNTs.

  3. Mechanical and Thermal Properties of Styrene Butadiene Rubber - Functionalized Carbon Nanotubes Nanocomposites

    KAUST Repository

    Laoui, Tahar

    2013-01-01

    The effect of reinforcing styrene butadiene rubber (SBR) with functionalized carbon nanotubes on the mechanical and thermal properties of the nanocomposite was investigated. Multi-walled carbon nanotubes (CNTs) were functionalized with phenol functional group to enhance their dispersion in SBR matrix. Surface functionalization of the CNTs was carried out using acid treatment and FTIR technique was utilized so as to ascertain the presence of phenol functional group. This was followed with the dispersion of the functionalized CNTs into a polymer solution and a subsequent evaporation of the solvent. This study has demonstrated the inherent capability of CNTs as reinforcing filler as demonstrated by the substantial improvement in Young\\'s Modulus, tensile strength and energy of absorption of the nanocomposites. The tensile strength increased from 0.17 MPa (SBR) to 0.48 MPa while the Young\\'s Modulus increased from 0.25 MPa to 0.83 MPa when 10wt% functionalized CNTs was added. With the addition of 1wt% reinforcement-a peak value of 4.1 KJ energy absorption was obtained. The homogenous dispersion of CNT-Phenol is thought to be responsible for the considerable enhancement in the reported properties. Copyright © Taylor & Francis Group, LLC.

  4. Application of Composite Powders Recycled from Graphite Tailings in Styrene-Butadiene Rubber

    Science.gov (United States)

    Hai, Yun; Liao, Libing; Lv, Guocheng; Qin, Faxiang; Mei, Lefu; Wei, Yaozu

    2015-11-01

    With styrene-butadiene rubber (SBR) as matrix and composite powders recycled from graphite tailings as fillers, the influence of the particle size and content of the composite powders on the tensile strength and electrical conductivity of the composite powder-filled SBR were studied. The results showed that composite powder recycled from graphite tailings could reinforce SBR, whose tensile strength was significantly increased with reducing the particle size of the composite powder, but it had little effect on the conductivity of the system. With composite powders as fillers in conjunction with conductive carbon black, the tensile strength and electrical conductivity of the system were greatly improved. The maximum tensile strength of the SBR filled with composite powder and conductive carbon black increased by 47% compared to that of the single composite powder-filled SBR. When the filling content of conductive carbon black was 10 phr and that of composite powder was above 30 phr, the volume resistivity of SBR showed a sharp decline, reaching a minimum about 106 Ω cm at 40 phr. All the results indicated that composite powder recycled from graphite tailings can be applied effectively as filler in SBR. It has great economic and environmental benefits.

  5. Preparation, characterization and conductivity study of nitro-mercurated styrene butadiene rubber/silver doped zinc oxide nanocomposites

    Science.gov (United States)

    Anilkumar, T.; Naik, Adarsh Ajith; Ramesan, M. T.

    2017-06-01

    Here we report the preparation of nitromercurated styrene butadiene rubber (NMSBR)/silver doped zinc oxide nanocomposite by inexpensive and ecofriendly two roll mill mixing. The composites were characterized by UV, FTIR, XRD, SEM, TGA and conductivity measurements. UV and FTIR spectrum indicated the interfacial interaction between the polymer and nanoparticles.XRD and SEM images showed the uniform arrangement of nanoparticles within the macromolecular chain. TGA study indicated the better thermal resistance of the composite. The dielectric properties and AC conductivity ofnanocomposites were much greater than nitromercurated SBR and they may be used as multifunctional materials for nanoelectronic devices.

  6. Effect of crosslinking density on biaxial relaxation of SBR by using reduced variables. [Styrene-Butadiene Rubber

    Science.gov (United States)

    Arenz, R. J.

    1974-01-01

    The use of reduced variables to account for the effect of crosslinking density in a styrene-butadiene rubber (SBR) system is demonstrated for general biaxial stress states. Recently published results from stress relaxation tests on five SBR vulcanizates crosslinked to different degrees by tetramethylthiuram disulfide were superposed by using the crosslinking density as a reduction variable. The equilibrium shear modulus calculated from the master relaxation curve at long reduced times was in satisfactory agreement with other results for SBR. The time-axis shifts were related in a linear logarithmic manner to the crosslinking density but had a slope slightly less than values previously reported for elastomer systems.

  7. The use of styrene-butadiene rubber waste as a potential filler in nitrile rubber: order of addition and size of waste particles

    Directory of Open Access Journals (Sweden)

    D. A. Baeta

    2009-03-01

    Full Text Available Styrene-butadiene rubber (SBR has large applications in the shoe industry, especially as expanded sheets used to produce insoles and inner soles. According to TG analysis, the rubber content in SBR residues (SBR-r was found to be around 26-wt%. Based on that data, a cost-effective technique for the reuse of SBR-r in Nitrile rubber (NBR was developed. Later, the effect of SBR-r on the cure behavior, mechanical performance, swelling, and crosslink density of reused rubber was investigated, with more emphasis placed on the effect of both particle size and loading of waste filler. Cure characteristics such as optimum cure time and scorch time were then reduced by the increasing amount of SBR-r filler. Owing to the reinforced nature of the largest particle size SBR-r, the best results for the mechanical properties of NBR were those in which SBR-r was added at the end of the cure process. The study has thus shown that SBR residue (SBR-r can be used as an economical alternative filler in NBR.

  8. Improved mechanical properties and ozone resistance of radiation-cured SBR. Final report, Dec 88-Jun 91. [Styrene Butadiene Rubber

    Energy Technology Data Exchange (ETDEWEB)

    Basfar, A.A.; Silverman, J.

    1991-08-01

    This report is a continuation and extension of the work of the earlier Army contract, where the superiority of the electron beam cured styrene butadiene rubber (SBR) tank pads to the sulfur cured pads was demonstrated. The focus of the present study is the investigation of the extraordinary ozone resistance of our radiation cured SBR, and also on possible alternatives for SBR, butadiene rubber (BR) in particular, as a tank pad compound. Base formulations of a fully sulfur cured system were established with 5% reproducibility, and results were confirmed by mechanical properties measurements on identical formulations from Belvoir Research Development and Engineering Center (BRDEC). Constant mechanical properties as a function of exposure to ozone indicate either competitive cross-linking and scissioning reactions or a 'protective' effect caused by higher terminal vinyl concentrations in the radiation cured formulations.

  9. The filler-rubber interface in styrene butadiene nanocomposites with anisotropic silica particles: morphology and dynamic properties.

    Science.gov (United States)

    Tadiello, L; D'Arienzo, M; Di Credico, B; Hanel, T; Matejka, L; Mauri, M; Morazzoni, F; Simonutti, R; Spirkova, M; Scotti, R

    2015-05-28

    Silica-styrene butadiene rubber (SBR) nanocomposites were prepared by using shape-controlled spherical and rod-like silica nanoparticles (NPs) with different aspect ratios (AR = 1-5), obtained by a sol-gel route assisted by a structure directing agent. The nanocomposites were used as models to study the influence of the particle shape on the formation of nanoscale immobilized rubber at the silica-rubber interface and its effect on the dynamic-mechanical behavior. TEM and AFM tapping mode analyses of nanocomposites demonstrated that the silica particles are surrounded by a rubber layer immobilized at the particle surface. The spherical filler showed small contact zones between neighboring particles in contact with thin rubber layers, while anisotropic particles (AR > 2) formed domains of rods preferentially aligned along the main axis. A detailed analysis of the polymer chain mobility by different time domain nuclear magnetic resonance (TD-NMR) techniques evidenced a population of rigid rubber chains surrounding particles, whose amount increases with the particle anisotropy, even in the absence of significant differences in terms of chemical crosslinking. Dynamic measurements demonstrate that rod-like particles induce stronger reinforcement of rubber, increasing with the AR. This was related to the self-alignment of the anisotropic silica particles in domains able to immobilize rubber.

  10. Research of operational properties of compound based on high viscosity styrene-butadiene rubber SSBR-2560 TDAE HV

    Directory of Open Access Journals (Sweden)

    M. I. Falyakhov

    2016-01-01

    Full Text Available The article consider the influence of replacement of SSBR-2560 TDAE batch production on high viscosity SSBR-2560-TDAE HV in the tread recipe on the tire performance properties. Obtained samples were highly viscosity styrene butadiene rubber did not differ in the microstructure of the SSBR-2560 TDAE batch production. Increasing the molecular weight possible to increase the Mooney viscosity of the rubber, however, is known to one of adverse factors is the deterioration of processability of rubber compounds based on polymers. In this connection, investigated the behavior in the step mixing compound based on high viscosity SSBR rubber. We chose recipes tread of the tire with a high content of organic silicon filler. It is established that the equivalent replacement of the polymer in the tread recipe does not lead to significant changes in the basic parameters of rubber mixing. We observed a slight increase in the energy consumption for the preparation of the rubber compounds, as well as the discharge temperature at each stage. It was shown to improve the distribution of the filler in the polymer matrix for the compound based on SSBR-2560 TDAE HV. The results showed that compound based on high viscosity SSBR improves rolling resistance and traction characteristics, while maintaining abrasion in comparison with the SSBR-2560-M27 batch production. Recommended use this brand in the production of rubber car tires.

  11. A styrene-butadiene rubber (SBR)/carbon nanotube-based smart force sensor for automotive tire deformation monitoring

    Science.gov (United States)

    Cho, Min-Young; Kim, Ji-Sik; Lee, Ho-Geun; Choi, Seung-Bok; Kim, Gi-Woo

    2016-04-01

    This paper provides a preliminary study on the piezoresistive effect of a styrene-butadiene Rubber (SBR), one of the main ingredients of automotive tire, dispersed with carbon nanotubes (CNTs) to explore its feasibility as a force sensor embedded in automotive tires. Typically, the application of CNTs has been successfully applied to the mechanical sensing technology such as a stress/strain and impact sensor. In this study, the potential of using the SBR/CNT as a force sensor for monitoring automotive tire deformation is evaluated for the first time. Experimental results show that the electrical resistance of the SBR/CNT composite changes in response to the sinusoidal loading, as well as static compressive load. These piezoresistive responses of the SBR/CNT composite will be used for sensing the tire deformation caused by the vehicle loading or cracks of tires.

  12. Radiation preparation of nano-powdered styrene-butadiene rubber (SBR) and its toughening effect for polystyrene and high-impact polystyrene

    Energy Technology Data Exchange (ETDEWEB)

    Li Daishuang; Xia Haibing [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Peng Jing [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China)], E-mail: jpeng@pku.edu.cn; Zhai Maolin; Wei Genshuan; Li Jiuqiang [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); Qiao Jinliang [Department of Applied Chemistry, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871 (China); SINOPEC, Beijing Research Institute of Chemical Industry, Beijing 100013 (China)

    2007-11-15

    Nano-powdered styrene-butadiene rubber (NPSBR) was synthesized based on the styrene-butadiene rubber (SBR) latex via gamma radiation crosslinking followed by spray drying. Two functional monomers, 2-ethyl hexyl acrylate (2-EHA) and trimethylolpropane triacrylate (TMPTA) were used as crosslinking agents. It was found that both 2-EHA and TMPTA can improve the radiation crosslinking of SBR latex. Transmission electron microscope (TEM) and scanning electron microscope (SEM) revealed that the NPSBR has a particle size similar to that of SBR latex with a diameter of 100 nm due to the high degree of crosslinking of SBR. Mechanical testing results showed that NPSBR could toughen polystyrene (PS) and high-impact polystyrene (HIPS) effectively. In addition, NPSBR is more suitable to toughen HIPS than PS at low rubber content.

  13. Surface modification of halloysite nanotubes by vulcanization accelerator and properties of styrene-butadiene rubber nanocomposites with modified halloysite nanotubes

    Science.gov (United States)

    Zhong, Bangchao; Jia, Zhixin; Hu, Dechao; Luo, Yuanfang; Guo, Baochun; Jia, Demin

    2016-03-01

    Vulcanization accelerant N-cyclohexyl-2-benzothiazole sulfenamide (CZ) was used as a surface modifier and chemically grafted on the surface of halloysite nanotubes (HNTs) to obtain CZ-functionalized HNTs (HNTs-s-CZ). It was found that HNTs-s-CZ could be homogeneously dispersed into styrene-butadiene rubber (SBR). The grafted CZ molecules, exactly located at the filler-rubber interface, reduced the activation energy of vulcanization of SBR/HNTs-s-CZ compounds. Besides, the density of chain segments introduced by the interfacial phase of SBR/HNTs-s-CZ nanocomposites was higher than the other nanocomposites with silane-modified HNTs (m-HNTs) or pristine HNTs, manifesting an indication of enhanced filler-rubber interfacial interaction in SBR/HNTs-s-CZ nanocomposites. Consequently, SBR/HNTs-s-CZ nanocomposites showed excellent mechanical properties. The tensile strength could be enhanced by as much as 38.6% and 102.5% compared to those of SBR/m-HNTs and SBR/HNTs nanocomposites, respectively, though containing equivalent accelerant component. The value of this work lies in the fact that apparent properties improvement of elastomer composites has been achieved by the incorporation of vulcanization accelerant-functionalized HNTs, which may be fruitful for the rational design of filler surface treatment and offer new scientific and technological opportunities for the preparation of high performance elastomer composites.

  14. Rheological properties of styrene-butadiene rubber filled with electron beam modified surface treated dual phase fillers[Styrene-butadiene rubber (SBR); Electron beam; Filler; Rheology; Die swell; Activation energy

    Energy Technology Data Exchange (ETDEWEB)

    Shanmugharaj, A.M.; Bhowmick, A.K. E-mail: anilkb@rtc.iitkgp.ernet.in

    2004-01-01

    The rheological properties of styrene-butadiene rubber (SBR) loaded with dual phase filler were measured using Monsanto Processability Tester (MPT) at three different temperatures (100 deg. C, 110 deg. C and 130 deg. C) and four different shear rates (61.3, 306.3, 613, and 1004.5 s{sup -1}). The effect of electron beam modification of dual phase filler in absence and presence of trimethylol propane triacrylate (TMPTA) or triethoxysilylpropyltetrasulphide (Si-69) on melt flow properties of SBR was also studied. The viscosity of all the systems decreases with shear rate indicating their pseudoplastic or shear thinning nature. The higher shear viscosity for the SBR loaded with the electron beam modified filler is explained in terms of variation in structure of the filler upon electron beam irradiation. Die swell of the modified filler loaded SBR is slightly higher than that of the unmodified filler loaded rubber, which is explained by calculating normal stress difference for the systems. Activation energy of the modified filler loaded SBR systems is also slightly higher than that of the control filler loaded SBR system.

  15. Thermal Stability and Flammability of Styrene-Butadiene Rubber-Based (SBR Ceramifiable Composites

    Directory of Open Access Journals (Sweden)

    Rafał Anyszka

    2016-07-01

    Full Text Available Ceramifiable styrene-butadiene (SBR-based composites containing low-softening-point-temperature glassy frit promoting ceramification, precipitated silica, one of four thermally stable refractory fillers (halloysite, calcined kaolin, mica or wollastonite and a sulfur-based curing system were prepared. Kinetics of vulcanization and basic mechanical properties were analyzed and added as Supplementary Materials. Combustibility of the composites was measured by means of cone calorimetry. Their thermal properties were analyzed by means of thermogravimetry and specific heat capacity determination. Activation energy of thermal decomposition was calculated using the Flynn-Wall-Ozawa method. Finally, compression strength of the composites after ceramification was measured and their micromorphology was studied by scanning electron microscopy. The addition of a ceramification-facilitating system resulted in the lowering of combustibility and significant improvement of the thermal stability of the composites. Moreover, the compression strength of the mineral structure formed after ceramification is considerably high. The most promising refractory fillers for SBR-based ceramifiable composites are mica and halloysite.

  16. Thermal Stability and Flammability of Styrene-Butadiene Rubber-Based (SBR) Ceramifiable Composites

    Science.gov (United States)

    Anyszka, Rafał; Bieliński, Dariusz M.; Pędzich, Zbigniew; Rybiński, Przemysław; Imiela, Mateusz; Siciński, Mariusz; Zarzecka-Napierała, Magdalena; Gozdek, Tomasz; Rutkowski, Paweł

    2016-01-01

    Ceramifiable styrene-butadiene (SBR)-based composites containing low-softening-point-temperature glassy frit promoting ceramification, precipitated silica, one of four thermally stable refractory fillers (halloysite, calcined kaolin, mica or wollastonite) and a sulfur-based curing system were prepared. Kinetics of vulcanization and basic mechanical properties were analyzed and added as Supplementary Materials. Combustibility of the composites was measured by means of cone calorimetry. Their thermal properties were analyzed by means of thermogravimetry and specific heat capacity determination. Activation energy of thermal decomposition was calculated using the Flynn-Wall-Ozawa method. Finally, compression strength of the composites after ceramification was measured and their micromorphology was studied by scanning electron microscopy. The addition of a ceramification-facilitating system resulted in the lowering of combustibility and significant improvement of the thermal stability of the composites. Moreover, the compression strength of the mineral structure formed after ceramification is considerably high. The most promising refractory fillers for SBR-based ceramifiable composites are mica and halloysite. PMID:28773726

  17. Surface modification of halloysite nanotubes by vulcanization accelerator and properties of styrene-butadiene rubber nanocomposites with modified halloysite nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Bangchao; Jia, Zhixin, E-mail: zxjia@scut.edu.cn; Hu, Dechao; Luo, Yuanfang; Guo, Baochun; Jia, Demin

    2016-03-15

    Graphical abstract: - Highlights: • Vulcanization accelerant was used to modify halloysite nanotubes (HNTs). • The modified HNTs reduced the activation energy of vulcanization. • Strong filler–rubber interaction was achieved in rubber/modified HNTs composites. • The modified HNTs exhibited excellent reinforcement effect on rubber. - Abstract: Vulcanization accelerant N-cyclohexyl-2-benzothiazole sulfenamide (CZ) was used as a surface modifier and chemically grafted on the surface of halloysite nanotubes (HNTs) to obtain CZ-functionalized HNTs (HNTs-s-CZ). It was found that HNTs-s-CZ could be homogeneously dispersed into styrene-butadiene rubber (SBR). The grafted CZ molecules, exactly located at the filler-rubber interface, reduced the activation energy of vulcanization of SBR/HNTs-s-CZ compounds. Besides, the density of chain segments introduced by the interfacial phase of SBR/HNTs-s-CZ nanocomposites was higher than the other nanocomposites with silane-modified HNTs (m-HNTs) or pristine HNTs, manifesting an indication of enhanced filler-rubber interfacial interaction in SBR/HNTs-s-CZ nanocomposites. Consequently, SBR/HNTs-s-CZ nanocomposites showed excellent mechanical properties. The tensile strength could be enhanced by as much as 38.6% and 102.5% compared to those of SBR/m-HNTs and SBR/HNTs nanocomposites, respectively, though containing equivalent accelerant component. The value of this work lies in the fact that apparent properties improvement of elastomer composites has been achieved by the incorporation of vulcanization accelerant-functionalized HNTs, which may be fruitful for the rational design of filler surface treatment and offer new scientific and technological opportunities for the preparation of high performance elastomer composites.

  18. Degree of Mechanochemical Devulcanization of Model Styrene-Butadiene Rubber Compounds Containing Different Amount of Poly-, Di- and Monosulphidic Bonds

    Science.gov (United States)

    Sangari, Samra; Anita, Hill; Dumitru, Pavel

    2004-03-01

    There have been significant attempts to devulcanize waste elastomers to facilitate reusing these valuable resources in applications requiring the unique properties of rubber. The difficulty in recycling of elastomers has traditionally been with devulcanizing the elastomer without comprising its properties due to degradation of main chains. This research aimed to devulcanize model styrene-butadiene rubber (SBR) compounds, which had various amounts of poly-, di- and monosulfidic crosslinks using a mechanochemical process. Three model compounds were prepared using SBR using a laboratory two-roll mill. They were then vulcanized in a compression molding press at 140r C. The prepared vulcanized compounds were then ground and devulcanized in an internal mixer using a chemical mixture at a constant rotor speed and temperature. The crosslink density of the compounds before and after the devulcanization was calculated using volume-swelling measurements. The obtained data was used to establish the correlation between crosslink density of the compounds and the degree of devulcanization. The results showed that mechanochemical devulcanization caused a significant decrease in the crosslink density of the compounds by breaking the sulfidic linkages. The break up of polysulfidic crosslinks was predominant, meaning that mechanochemical process selectively affected different types of crosslinks.

  19. Plane-interface-induced lignin-based nanosheets and its reinforcing effect on styrene-butadiene rubber

    Directory of Open Access Journals (Sweden)

    C. Jiang

    2014-09-01

    Full Text Available Lignin was viewed as a spherical microgel in aqueous alkali. While spread out in a monolayer or adsorbed on a surface, lignin was made up of flexible, disk-like molecules with approximately the same thickness of 2 nm. According to this principle, we employed the lamina of montmorillonite (MMT as a plane template to anchor cationic lignin (CL on its two sides, resulting in the formation of CL-MMT hybrid materials (CLM. The isotherm adsorption behavior and structure characteristics of CLM were studied. The results showed that CLM was individually dispersed nanosheets with a thickness of about 5 nm when the mass ratio of CL to MMT is more than 2:1 and prepared at acidic or neutral pH. Compared to the cocoagulation of lignin and styrene-butadiene rubber (SBR, CLM obviously accelerated the coagulation rate, due to the reduction of surface activity of CL restricted by MMT. The nanoscale dispersion of CLM in SBR matrix significantly improved the tensile strength of CLM/SBR nanocomposites to 14.1 MPa by adding only 10 phr CLM and cardanol glycidyl ether (CGE as compatibilizer. Dynamic mechanical analysis (DMA showed that the glass transition temperature of SBR/CLM nanocomposites decreased with increasing CLM loading. Correspondingly, a special interfacial structure was proposed.

  20. Effect of carbon black composition with sludge palm oil on the curing characteristic and mechanical properties of natural rubber/styrene butadiene rubber compound

    Science.gov (United States)

    Mohamed, R.; Nurazzi, N. Mohd; Huzaifah, M.

    2017-07-01

    This study was conducted to investigate the possibility of utilizing sludge palm oil (SPO) as processing oil, with various amount of carbon black as its reinforcing filler, and its effects on the curing characteristics and mechanical properties of natural rubber/styrene butadiene rubber (NR/SBR) compound. Rubber compound with fixed 15 pphr of SPO loading, and different carbon black loading from 20 to 50 pphr, was prepared using two roll mills. The cure characteristics and mechanical tests that have been conducted are the scorch and cure time analysis, tensile strength and tear strength. Scorch time (ts5) and cure time (t90) of the compound increases with the increasing carbon black loading. The mechanical properties of NR/SBR compound viz. the tensile strength, modulus at 300% strain and tear strength were also improved by the increasing carbon black loading.

  1. Caracterização de artefatos elastoméricos obtidos por revulcanização de resíduo industrial de SBR (copolímero de butadieno e estireno Characterization of elastomeric artifacts obtained by revulcanization of SBR industrial waste (Styrene-butadiene Rubber

    Directory of Open Access Journals (Sweden)

    Tatiana Weber

    2011-01-01

    Full Text Available A reciclagem de resíduos de borracha é de extrema importância nos dias de hoje, tanto em relação aos impactos ambientais quanto à conservação de energia. Considerando que a maioria dos trabalhos publicados atualmente se refere à reciclagem de pneus, o objetivo deste trabalho foi desenvolver e caracterizar formulações contendo um tipo de resíduo industrial, proveniente da fabricação de perfis automotivos, à base de copolímero de butadieno e estireno (SBR para possível aplicação na própria empresa. As composições foram preparadas e caracterizadas pela determinação das propriedades térmicas (calorimetria diferencial de varredura, reológicas (analisador de processamento de borracha, reométricas (reômetria de disco oscilatório, mecânicas (resistência à tração e ao rasgamento, químicas (densidade de ligações cruzadas e morfológicas (microscopia eletrônica de varredura. Os resultados obtidos para as composições foram comparados aos de uma amostra controle, de mesma composição, que foi fornecida pela empresa geradora do resíduo de SBR. Os resultados mecânicos indicaram que o processo de revulcanização proposto foi efetivo. Os valores dos parâmetros de tensão na ruptura e resistência ao rasgamento foram de 70 e 50%, respectivamente, em relação aos valores encontrados para a amostra controle, indicando a possibilidade do uso desse resíduo em artefatos de menor exigência técnica.The recycling of waste rubber has very important significances, such as protection of the environment and conservation of energy. Considering that most of published works concerning this subject are about tire recycling, the objective of this work was to develop and characterize formulations containing a type of industrial waste, from the manufacture of automotive profiles, based on styrene-butadiene rubber (SBR for possible application in the industry. The compositions were formulated and characterized by thermal (differential

  2. Birchwood biochar as partial carbon black replacement in styrene-butadiene rubber composites

    Science.gov (United States)

    Birchwood feedstock was used to make slow pyrolysis biochar that contained 89% carbon and rubber. Composites made from blended fillers of 25/75 biochar/carbon black were equivalent to or superior to their 100% carbo...

  3. On the form of the strain energy function for a family of SBR materials. [Styrene-Butadiene Rubber

    Science.gov (United States)

    Arenz, R. J.

    1977-01-01

    Styrene-butadiene materials with varying crosslink densities are analyzed through use of a strain energy function of the type introduced by Valanis and Landel (1967). A form of the strain energy function derived from strip biaxial tests proves to be accurate when checked against uniaxial and other biaxial test results.

  4. Observations made during stretching, tearing and failure of NR (natural rubber) and SBR (styrene-butadiene rubber) loaded with various amounts of carbon black

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A.; Lesuer, D.R.; Patt, J.

    1988-02-01

    In order to effectively utilize fractography as an aid in identifying the influence of material and service (or test) parameters on material properties, one must first understand the origin of the morphological features developed during the tearing and fracturing of these elastomers. At our laboratory, we have made extensive fractographic studies while evaluating the effects of material formulations, temperature, and loading rates on the loading response, tearing energy, induced damage, and tearing phenomena in SBR (Styrene Butadiene Rubber) containing different amounts of CB (Carbon Black) filler. We have also examined failures in tank track pads, as well as laboratory-tested samples cut from new track pads. In this paper we report on observations made during the actual stretching, tearing and failure of elastomeric samples pulled in tension at a constraint stroke-diplacement rate. 15 refs., 12 figs.

  5. Performance of Styrene Butadiene Rubber as a Concrete Repair Material in tropical climate

    Science.gov (United States)

    Radhakrishnan, R.; Prakash, V. Syam; Thampan, C. K.; Varma, Prasad

    2012-11-01

    Deterioration of Concrete due to variety of reasons like corrosion of steel, inferior quality of materials as well as workmanship and exposure to aggressive environment like thermal cycling affect the performance or damage a number of Reinforced cement concrete structures. In order to repair these structures for enhancing the service life, number of methods and materials are available. But the degree of success of any repair in concrete depends mainly on the correct choice and the method of application of repair materials. This paper discusses the details of an experimental investigation on the performance of Styrene ñ Butadiene Rubber (SBR) as a concrete repair material in tropical climatic conditions. Resistance to water penetration and tensile cracking are two important performance criteria for any repair material. Cement mortar cubes of mix proportion 1:3 with SBR added at the rate of 20% of the weight of cement, and control specimens without SBR were made. Compressive strength and sorptivity values of the cubes were determined. Shear Bond strength (by slant shear test) and splitting tensile strength of the repaired cylinder specimens of standard dimensions, in which SBR used as a bonding agent were determined. These values were compared with the values obtained for the similar specimens, in which the bonding agent applied was conventional cement slurry. The influence of thermal cycling on the properties of repaired concrete specimens were also studied. A comparison has also been made with the values required to meet the standard specifications of a repair material.

  6. Enhancing mechanical and thermal properties of styrene-butadiene rubber/carboxylated acrylonitrile butadiene rubber blend by the usage of graphene oxide with diverse oxidation degrees

    Science.gov (United States)

    Xue, Xiaodong; Yin, Qing; Jia, Hongbing; Zhang, Xuming; Wen, Yanwei; Ji, Qingmin; Xu, Zhaodong

    2017-11-01

    Graphene oxide (GO) with various oxidation degrees were prepared through a modified Hummer's method by varying the dosage of oxidizing agent. Styrene-butadiene rubber (SBR)/carboxylated acrylonitrile butadiene rubber (XNBR)/GO nanocomposites were fabricated by aqueous-phase mixing of GO colloidal dispersion with SBR latex and a small loading of XNBR latex, followed by co-coagulation. Effects of GO oxidation degree on the morphology, structure, mechanical and thermal properties of nanocomposites were thoroughly investigated. The results showed that the mechanical strength of nanocomposites were enhanced with the increase of oxidation degree of GO. Especially, when the weight ratio of KMnO4 to graphite was 15/5, the tensile strength, tear strength and thermal conductivity of SBR/XNBR/GO filled with 3 phr (parts per hundred rubber) GO increased by 255.3%, 141.5% and 22.8%, respectively, compared to those of neat SBR/XNBR blend. In addition, the thermal stability and the solvent resistance of the nanocomposites were also improved significantly. This work suggested that GO with higher oxidation degree could effectively improve the properties of SBR/XNBR blend.

  7. Adhesion properties of styrene-butadiene rubber (SBR/Standard Malaysian Rubber (SMR L-based adhesives in the presence of phenol formaldehyde resin

    Directory of Open Access Journals (Sweden)

    2007-10-01

    Full Text Available The adhesion properties, i. e. viscosity, tack and peel strength of styrene-butadiene rubber (SBR/Standard Malaysian Rubber (SMR L-based pressure-sensitive adhesive was studied using phenol formaldehyde resin as the tackifying resin. Toluene was used as the solvent throughout the experiment. SBR composition in SBR/SMR L blend used was 0, 20, 40, 60, 80, 100%. Three different resin loadings, i. e. 40, 80 and 120 parts per hundred parts of rubber (phr were used in the adhesive formulation. The viscosity of adhesive was determined by a HAAKE Rotary Viscometer whereas loop tack and peel strength of paper/polyethylene terephthalate (PET film were measured using a Lloyd Adhesion Tester operating at 30 cm/min. Results indicate that the viscosity of adhesive decreases with increasing % SBR whereas loop tack passes through a maximum value at 20% SBR for all resin loadings. Except for the control sample (without resin, the peel strength shows a maximum value at 60% SBR for the three modes of peel tests. For a fixed % SBR, adhesive sample containing 40 phr phenol formaldehyde resin always exhibits the highest loop tack and peel strength, an observation which is associated to the optimum wettability of adhesive on the substrate.

  8. Prediction of Flexural Strength of Concretes Containing Silica Fume and Styrene-Butadiene Rubber (SBR) with an Empirical Model

    Science.gov (United States)

    Shafieyzadeh, M.

    2015-12-01

    In the flexural test, the theoretical maximum tensile stress at the bottom fiber of a test beam is known as the modulus of rupture or flexural strength. This work deals with the effects of Silica Fume and Styrene-Butadiene Latex (SBR) on flexural strength of concrete. An extensive experimentation was carried out to determine the effects of silica fume and SBR on flexural strength of concrete. Two water-binder ratios and several percentages of silica fume and SBR were considered. Abrams' Law, which was originally formulated for conventional concrete containing cement as the only cementations material, is used for prediction of flexural strength of these concretes. The aim of this work is to construct an empirical model to predict the flexural strength of silica fume-SBR concretes using concrete ingredients and time of curing in water. Also, the obtained results for flexural strength tests have been compared with predicted results.

  9. Damping of Mechanical Waves with Styrene/Butadiene Rubber Filled with Polystyrene Particle: Effects of Particles Size and Wave Frequency

    Directory of Open Access Journals (Sweden)

    M. Haghgo

    2007-08-01

    Full Text Available Utilizing polymeric materials for damping mechanical waves is of great importance in various fields of applications such as military camouflage, prevention of structural vibrational energy transfer, and noise attenuation. This ability originates from segmental dynamics of chain-like polymer molecules. Damping properties of styrene-butadiene rubbercontaining 10 wt% of monosize polystyrene particles with different diameters (from 80 nm to 500 μm was investigated in the frequency range of vibration, sound, and ultrasound via dynamic mechanical thermal analysis, normalsound adsorption test, and ultrasound attenuation coefficient measurement. The obtained results indicated that for different systems, containing different sizes of polystyrene particles, the area under the damping curve does not show significant change comparing to the neat SBR in the frequency range studied. However, addition of polystyrene particles, specifically nanosized particles, resulted in emergence of a secondary glass transition temperature which could be attributed to the modified dynamics of a layer of matrix molecules near the surface of PS particles. In the range of sound frequency, 0.5 to 6.3 kHz, the maximum damping was observed for the system containing polystyrene nanoparticles. However the single damping curve of neat SBR was separated into two or even three distinct curves owing to the presence of the particles. The maximum damping in the ultrasound frequency range was found for the system containing 0.5 mm polystyrene particles. This is attributed to different contributions from matrix chains dynamics and the reflection of mechanical waves from particles-matrix interface at different frequency ranges. On other words, the increase in the glass transition temperature of the elastomeric matrix phase with increasing the mechanical wave frequency causes a reduction in the contribution from matrix chains dynamics while the contribution due to diffraction from dispersed

  10. Utilizing carbon dioxide as a reaction medium to mitigate production of polycyclic aromatic hydrocarbons from the thermal decomposition of styrene butadiene rubber.

    Science.gov (United States)

    Kwon, Eilhann E; Yi, Haakrho; Castaldi, Marco J

    2012-10-02

    The CO(2) cofeed impact on the pyrolysis of styrene butadiene rubber (SBR) was investigated using thermogravimetric analysis (TGA) coupled to online gas chromatography/mass spectroscopy (GC/MS). The direct comparison of the chemical species evolved from the thermal degradation of SBR in N(2) and CO(2) led to a preliminary mechanistic understanding of the formation and relationship of light hydrocarbons (C(1-4)), aromatic derivatives, and polycyclic aromatic hydrocarbons (PAHs), clarifying the role of CO(2) in the thermal degradation of SBR. The identification and quantification of over 50 major and minor chemical species from hydrogen and benzo[ghi]perylene were carried out experimentally in the temperature regime between 300 and 500 °C in N(2) and CO(2). The significant amounts of benzene derivatives from the direct bond dissociation of the backbone of SBR, induced by thermal degradation, provided favorable conditions for PAHs by the gas-phase addition reaction at a relatively low temperature compared to that with conventional fuels such as coal and petroleum-derived fuels. However, the formation of PAHs in a CO(2) atmosphere was decreased considerably (i.e., ∼50%) by the enhanced thermal cracking behavior, and the ultimate fates of these species were determined by different pathways in CO(2) and N(2) atmospheres. Consequently, this work has provided a new approach to mitigate PAHs by utilizing CO(2) as a reaction medium in thermochemical processes.

  11. Characterization of free volume during vulcanization of styrene butadiene rubber by means of positron annihilation lifetime spectroscopy and dynamic mechanical test.

    Science.gov (United States)

    Marzocca, A J; Cerveny, S; Salgueiro, W; Somoza, A; Gonzalez, L

    2002-02-01

    An experimental investigation was performed to study the effect on the free volume of the advance of the cross-linking reaction in a copolymer of styrene butadiene rubber by sulfur vulcanization. The dynamic modulus and loss tangent were evaluated over samples cured for different times at 433 K by dynamic mechanical tests over a range of frequencies between 5 and 80 Hz at temperatures between 200 and 300 K. Using the William-Landel-Ferry relationship, master curves were obtained at a reference temperature of 298 K and the coefficients c(0)(1) and c(0)(2) were evaluated. From these parameters the dependence of the free volume on the cure time is obtained. Positron annihilation lifetime spectroscopy was also used to estimate the size and number density of free volume sites in the material. The spectra were analyzed in terms of continuous distributions of free volume size. The results suggest an increase of the lower free volume size when cross linking takes place. Both techniques give similar results for the dependence of free volume on the time of cure of the polymer.

  12. Water soluble styrene butadiene rubber and sodium carboxyl methyl cellulose binder for ZnFe2O4 anode electrodes in lithium ion batteries

    Science.gov (United States)

    Zhang, Rongyu; Yang, Xu; Zhang, Dong; Qiu, Hailong; Fu, Qiang; Na, Hui; Guo, Zhendong; Du, Fei; Chen, Gang; Wei, Yingjin

    2015-07-01

    ZnFe2O4 nano particles as an anode material for lithium ion batteries are prepared by the glycine-nitrate combustion method. The mixture of styrene butadiene rubber and sodium carboxyl methyl cellulose (SBR/CMC) with the weight ratio of 1:1 is used as the binder for ZnFe2O4 electrode. Compared with the conventional polyvinylidene-fluoride (PVDF) binder, the SBR/CMC binder is much cheaper and environment benign. More significantly, this water soluble binder significantly improves the rate capability and cycle stability of ZnFe2O4. A discharge capacity of 873.8 mAh g-1 is obtained after 100 cycles at the 0.1C rate, with a very little capacity fading rate of 0.06% per cycle. Studies show that the SBR/CMC binder enhances the adhesion of the electrode film to the current collector, and constructs an effective three-dimensional network for electrons transport. In addition, the SBR/CMC binder helps to form a uniform SEI film thus prohibiting the formation of lithium dendrite. Electrochemical impedance spectroscopy shows that the SBR/CMC binder lowers the ohmic resistance of the electrode, depresses the formation of SEI film and facilitates the charge transfer reactions at the electrode/electrolyte interface. These advantages highlight the potential applications of SBR/CMC binder in lithium ion batteries.

  13. Graft modification of styrene-butadiene rubber with. gamma. -mercaptpropyltrimethoxysilane. Gamma. -mercaptpropyltrimethoxysilane wo mochiita SBR no graft kaishitsu

    Energy Technology Data Exchange (ETDEWEB)

    Kodama, S.; Kawasaki, H.; Mitsuishi, K.; Nishi, K. (Industrial Technology Center of Okayama, Okayama (Japan))

    1991-08-05

    The method of irradiation to rubber sheet kneaded with {gamma}-MPS (mercaptpropyltrimethoxysilane) is studied as a simple rubber modification method, and the blended effect of silica on the reformed rubber sheet is investigated. Graft modification can be made by using a photo-initiator. The graft efficiency reaches near 90% in nitrogen gas flow with 90 minute irradiation. However, the reaction in air is slow with low graft efficiency, and gelation of rubber is observed. The 300% modulus of the modified vulcanized rubber has comparatively low graft rate which is larger than unreformed one or the one blended with {gamma}-MPS surface reforming silica, and the tear strength, compression permanent deformation, wear resistance, etc. are also improved. The interface adhesive between rubber and filler is better than that in the case where {gamma}-MPS is used as the surface reformer for silica. If the specimen is left at room temperature after irradiation, remarkable gelation is observed. 7 refs., 7 figs., 3 tabs.

  14. Effects of interfacial interaction on the properties of poly(vinyl chloride)/styrene-butadiene rubber blends

    Science.gov (United States)

    Zhu, Shuihan

    PVC/SBR blends---new thermoplastic elastomer material---were developed. They have potential applications due to low costs and low-temperature elasticity. A unique compatibilization method was employed to enhance the mechanical properties of the materials a compatibilizer miscible with one of the blend components can react chemically with the other component(s). Improvements in tensile and impact behavior were observed as a result of the compatibilization. A novel characterization technique to study the interface of PVC/SBR blends was developed. This technique involves the observation of the unstained sample under electron beam irradiation by a transmission electron microscope (TEM). An enrichment of rubber at the interface between PVC and SBR was detected in the compatiblized PVC/SBR blends. Magnetic relaxation measurements show that the rubber concentration in the proximity of PVC increases with the degree of covulcanization between NBR and SBR. The interface development and the rheological effect during processing were investigated. The interfacial concentration profile and the interfacial thickness were obtained by grayscale measurements on TEM micrographs, evaluation of SIMS images, and measurements of micromechanical properties.

  15. Influence of pyrolytic carbon black and pyrolytic oil made from used tires on the curing and (dynamic mechanical properties of natural rubber (NR/styrene-butadiene rubber (SBR blends

    Directory of Open Access Journals (Sweden)

    F. Karabork

    2016-01-01

    Full Text Available Pyrolytic carbon black (CBp and pyrolytic oil (Op made from used tires were used in natural rubber (NR/styrene-butadiene rubber (SBR blends. The effects of CBp and Op on the processing properties, the mechanical properties and the dynamic mechanical properties of the NR/SBR blends were investigated and compared with a control sample that was prepared with N550 and commercial process oil. It was found that the effect of CBp on the processing properties of the NR/SBR blends was similar to that of N550. With the increase of the CBp content, the curing properties of the NR/SBR blends changed little. The reinforcing effect of CBp was inferior to that of N550. With the increase of the CBp content, the tensile strength, tear strength and modulus at 100% elongation of the NR/SBR vulcanizates decreased significantly. Dynamic mechanical properties of the NR/SBR blends were also affected and all samples comprising CBp have a higher tan δ than control sample. It is suggested that the low surface area and high ash content of CBp strongly effects all of these property changes of the NR/SBR blends. The morphology and distribution of the carbon black particles are studied using a scanning electron microscope. It was also found that with the increase of the Op content, the properties of the NR/SBR blends were strongly affected due to the high sulfur content of Op, which produced a high crosslinking density.

  16. New dual-phase polymer electrolytes prepared from NBR/SBR lattices. [polyacryloNitrile-Butadiene Rubber/poly(Styrene-Butadiene) copolymer Rubber

    Energy Technology Data Exchange (ETDEWEB)

    Matsumoto, Morihiko; Ichino, Toshihiro; Rutt, J.S.; Nishi, Shiro (Nippon Telegraph and Telephone Corp., Tokyo (Japan). NTT Interdisciplinary Research Lab.)

    1993-10-01

    A new type of Li[sup +] ion conducting polymer electrolytes consisting of two phases, one of which is a highly polar region (impregnated with lithium salt solution), forming ion-conductive channels, while the other is a nonpolar region, forming supporting polymer matrices have been prepared from NBR/SBR lattices. TEM measurement and EDX analysis show evidence that dual-phase structure is constructed in the electrolyte. Ionic conductivity of the electrolyte increases with increase of lithium salt solution content. Maximum ionic conductivity of 2.2 [times] 10[sup [minus]3] S/cm is obtained at the lithium salt solution content of 60.5% (w/w). The electrolyte retains rubber-like film with good mechanical strength despite the presence of the solution.

  17. Devulcanization of styrene butadiene (SBR) waste tire by controlled oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Rios, Rachel R.V.A.; Gontijo, Manuela; Ferraz, Vany P.; Lago, Rochel M.; Araujo, Maria Helena [Minas Gerais Univ., Belo Horizonte, MG (Brazil). Dept. de Quimica]. E-mail: mharaujo@ufmg.br

    2006-05-15

    This work describes the devulcanization of vulcanized SBR (Styrene Butadiene Rubber) based on controlled oxidation with nitric acid. IR, {sup 1}H and {sup 13}C-NMR, CHN elemental analyses, TG, GPC and TPD-MS (Temperature Programmed Decomposition-Mass Spectrometry) experiments suggest that nitric acid promotes two processes: devulcanization by oxidation of the sulfide crosslinks and oxidation of the carbon framework leading to the formation of -COOH and -NO{sub 2} groups. Under aggressive conditions (HNO{sub 3}, reflux) the polymer chain is strongly oxidized and fragmented to a highly oxygenated low molecular weight fraction, which is soluble in water. (author)

  18. Mechanical and optical effects of elastomer interaction in polypropylene modification: Ethylene-propylene rubber, poly-(ethylene-co-octene and styrene-butadiene elastomers

    Directory of Open Access Journals (Sweden)

    M. Gahleitner

    2012-09-01

    Full Text Available The interaction between binary combinations of three different elastomer classes commonly applied in impact modification of isotactic polypropylene (iPP was studied. Blends based on a homogeneous ethylene-propylene (EP random copolymer (EP-RACO and a heterophasic EP impact copolymer comprising ethylene-propylene rubber (EPR with different external elastomer types, one homogeneous ethylene-1-octene copolymer (EOC, and two hydrogenated styrenebutadiene-styrene triblock copolymers (SEBS with different styrene content, were prepared. The phase morphology, mobility as a function of temperature, mechanical and optical properties were studied. Special effects could be achieved for the combination of two different elastomer types. The results clearly demonstrate the possibility to achieve attractive property combinations in ternary systems consisting of a crystalline PP matrix and two different types of elastomer, EPR or EOC on the one hand and SEBS on the other hand. A combination of density matching and compatibilization effects allows reaching good low temperature impact strength together with a transparency close to matrix level when selecting a butadiene-rich SEBS type.

  19. Effect of concentration and humidity on the formation of porous polymer films using Styrene Butadiene Co-Polymer

    Science.gov (United States)

    Jose, Renu; Sujith, A.; Predeep, P.

    2011-10-01

    Honeycomb structured porous materials from complex polymers are formed using water droplet templating method. In the present work microporous films were prepared from styrene butadiene rubber (SBR) using emulsion technique. The pore sizes can be easily tuned by changing the concentration and the humidity condition. The pore size is characterized by optical microscope and Scanning electron microscope (SEM). These films can be used for various applications in optoelectronics, photonics, catalysis, tissue engineering, bioanalytical purposes etc.

  20. SYNTHESIS OF STYRENE-BUTADIENE STATISTIC COPOLYMERS CONTAINING MAGNESIUM INITIATOR

    Directory of Open Access Journals (Sweden)

    A. V. Firsova

    2015-01-01

    Full Text Available The article discusses the use of organomagnesium initiators in the synthesis of styrene-butadiene random copolymer (SBR obtained solution polymerization and their influence on the properties of rubber. Selected organic magnesium dialkyl initiator is combined with a modifier, which is a mixed alkoxide of an alkali and alkaline earth metals, which allows to control the micr ostructure of the diene polymer and its molecular weight characteristics. Alcohol derivatives selected high-boiling alcohols tetra (hydroxypropyl ethylenediamine (lapromol 294 and tetrahydrofurfuryl alcohol (TGFS. Selection of high-boiling alcohols due to the fact that the destruction of alkoxide with aqueous polymer degassing they do not fall into the return solvent and almost fall into the exact water. The metal components of alkoxides are lithium, sodium, potassium, magnesium and calcium. The resulting solutions are stable when stored modifier t hroughout the year even at -40 °C. The scheme of obtaining the new catalyst systems based organomagnesium and alcoxide of alkali and alkaline earth metals, which yields as functionalized SBR with a statistical and a distribution block of butadiene and styrene was developed. The process of copolymerization with styrene to butadiene organomagnesium initiators as using an organolithium compound (n-butyllithium was carried out, and without it. Found that the addition of n-butyllithium in the reaction mixture leads to a sharp increase in the rate of reaction. The results of studies of the effect of composition of the initiator system on the structure of diene polymers. It was revealed that a mixed initiator system affords a high conversion of monomers (to 90 % in 1 hour 1,2-polybutadiene content increased to 60 %. The process of polymerization of only a mixture of organomagnesium initiators and alcoxide of alkali and alkaline earth metals are not actively proceeds, conversion of the monomers reaches to 90 % in 4 hours, the microstructure

  1. The evaluation of tetrabutylamonium bis(4-ethylphenylsulphonyldithiocarbimate)zincate(II) (ZNIBU) efficiency as a reclaiming agent for styrene-butadiene rubber (SBR); Avalicao da eficiencia do bis(4-metilfenilsulfonilditiocarbimato)zincato(II) de tetrabutilamonio (ZNIBU) como agente de regeneracao para borracha de butadieno-estireno (SBR)

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, Pedro H.H.; Visconte, Leila L.Y.; Pacheco, Elen B.A.V., E-mail: pedro_hhm@ima.ufrj.br [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil); Tavares, Eder C. [Universidade Federal de Itajuba (UNIFEI), Itajuba, MG (Brazil)

    2015-07-01

    In recent years, the production of rubber waste has been reported as a serious environmental problem. The chemical structure of rubbers (crosslinked, insoluble and infusible polymers) makes its reprocessing very difficult, unlike thermoplastics. The most common methods to treat rubber waste are of thermal, mechanical and chemical nature, wherein the chemical methods the purpose is to regenerate the rubber. Early studies with tetrabutylamonium bis(4-methylphenylsulphonyldithiocarbimate)zincate(II) (ZNIBU) point to its ability as an accelerator in the rubber curing process. In this work, this zinc complex was evaluated as a chemical regeneration agent. ZNIBU was synthesized and characterized by Nuclear Magnetic Resonance ({sup 13}C NMR) and Fourier Transform Infrared Spectroscopy (FTIR). The mixture of virgin SBR with vulcanization ingredients was performed in a two-roll mill, and the composition was then vulcanized and molded on a hydraulic press. The synthesized ZNIBU was then mixed with the vulcanized rubber and devulcanization was observed. Finally, the devulcanized elastomeric composition was revulcanized. The revulcanization of SBR regenerated with ZNIBU led to the formation of a rubber with maximum torque near the maximum torque of the virgin vulcanized rubber. After adjusting the optimal conditions of regeneration, mechanical tests will be carried out (tensile strength, tear strength and hardness) for the specimens of both vulcanized and revulcanized rubbers in order to compare their mechanical properties. (author)

  2. Radiation vulcanization of rubbers

    Energy Technology Data Exchange (ETDEWEB)

    Makuuchi, Keizo [Japan Atomic Energy Research Inst., Takasaki, Gunma (Japan). Takasaki Radiation Chemistry Research Establishment

    2002-02-01

    An abstract of the radiation process of polymer materials and the polymer reaction by radiation is explained. Main radiation is 250 keV to 10 MeV of electron rays in the industry. Radiation cross-linked rubber has less the tensile strength than that by sulfur and organic peroxide crosslinking. The main origins of low tensile strength are caused by cut of backbone chain and ozone depend on radiation. Acceleration of crosslinking and short time of radiation are necessary to improve these defects. To accelerate crosslinking, we used crosslinking accelerators, for example, three poly-functional monomers (PFM). The maximum tensile strength of styrene-butadiene rubber (SBR) not added crosslinking accelerators showed 3 MPa at 110 kGy, but SBR added A-TMMT (tetramethylolmethane tetraacrylate) showed 5.5 MPa at 110 kGy. Radiation crosslinking of many kinds of rubber: isoprene (IR), SBR, CR, nitrile rubber (NBR), hydrogenated nitrile rubber (HNBR), butyl rubber (IIR), chlorinated butyl rubber (CIIR), EPM and TPE are explained. (S.Y.)

  3. Bond Characteristics of Macro Polypropylene Fiber in Cementitious Composites Containing Nanosilica and Styrene Butadiene Latex Polymer

    Directory of Open Access Journals (Sweden)

    Jae-Woong Han

    2015-01-01

    Full Text Available This study evaluated the bond properties of polypropylene (PP fiber in plain cementitious composites (PCCs and styrene butadiene latex polymer cementitious composites (LCCs at different nanosilica contents. The bond tests were evaluated according to JCI SF-8, in which the contents of nanosilica in the cement were 0, 2, 4, 6, 8, and 10 wt%, based on cement weight. The addition of nanosilica significantly affected the bond properties between macro PP fiber and cementitious composites. For PCCs, the addition of 0–2 wt% nanosilica enhanced bond strength and interface toughness, whereas the addition of 4 wt% or more reduced bond strength and interface toughness. The bond strength and interfacial toughness of LCCs also increased with the addition of up to 6% nanosilica. The analysis of the relative bond strength showed that the addition of nanosilica affects the bond properties of both PCC and LCC. This result was confirmed via microstructural analysis of the macro PP fiber surface after the bond tests, which revealed an increase in scratches due to frictional forces and fiber tearing.

  4. Thermal Analysis Characterization of Elastomers and Carbon Black Filled Rubber Composites for Army Applications

    Science.gov (United States)

    1985-06-01

    RUBBER COMPOSITES FOR ARMY APPLICATIONS 6. PERFORMING ORO. REPORT NUMBER 7. AUTHOR(q) S. CONTRACT OR GRANT NUMBER(41) Robert E. Sacher, Domenic P...Roadwheei Side SP - Standard Products SBR - Styrene-butadiene Rubber SR - Synthetic Rubber ( SBR or SBR -BR) TR - Track Rubber U - Uncured iii... applications ranging from automotive and aircraft tires to rubber belts, hoses, and seals. Although thermal studies on rubber materials closely

  5. Best Practice for the Devulcanization of Sulfur-cured SBR Rubber

    NARCIS (Netherlands)

    Saiwari, Sitisaiyidah; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.; Blume, Anke

    2015-01-01

    In the present paper, special attention will be devoted to thermo-chemical devulcanization of sulfur-cured styrene butadiene rubber (SBR) using diphenyldisulfide (DPDS) as devulcanization aid. SBR is the main component in whole passenger car tire rubber and, at the same time, the most critical one

  6. Improved natural rubber composites reinforced with a complex filler network of biobased nanoparticles and ionomer

    Science.gov (United States)

    Biobased rubber composites are renewable and sustainable. Significant improvement in modulus of rubber composite reinforced with hydrophilic filler was achieved with the inclusion of ionomers. Soy particles aided with ionomer, carboxylated styrene-butadiene (CSB), formed a strong complex filler netw...

  7. Mutagenicity of rubber vulcanization gases in Salmonella typhimurium.

    Science.gov (United States)

    Hedenstedt, A; Ramel, C; Wachtmeister, C A

    1981-01-01

    Gases formed by rubber and rubber additives in the vulcanization process were collected with a laboratory-scale glass apparatus. Mutagenicity testing of the vulcanization gases by the Salmonella/microsome test was conducted with strains TA1535, TA1538, TA98, and TA100 in the absence and presence of a metabolizing system from rat liver homogenates. The mutagenicity of gases derived by heating chloroprene rubber and ethylene propylene rubber was established with both base substitution- and frameshift-sensitive strains and that of a styrene-butadiene rubber was established with the base substitution-sensitive stain TA100. Tests on pyrolysis gases from a butadiene acrylonitrile rubber revealed only toxic effects. Curing systems, additives, and filling materials from various sources were represented in the material. Gases were collected at temperature levels corresponding to both mixing and curing of these particular rubbers in the industrial operations. Attempts were made to correlate the mutagenicity of the gases to the presence of mutagenic components in the rubber mixtures.

  8. The challenges of silica-silane reinforcement of natural rubber

    NARCIS (Netherlands)

    Dierkes, Wilma K.; Sarkawi, S.S.; Noordermeer, Jacobus W.M.

    2012-01-01

    In recent years, highly-dispersible silica has become the preferred alternative to carbon-black as reinforcing filler for low rolling-resistance tires. However, the application of this filler system is so far limited to passenger car tires, as their treads contain styrene butadiene rubber (SBR). In

  9. Structure–property relationships of ‘safe’ aromatic oil based passenger car tire tread rubber compounds

    NARCIS (Netherlands)

    Rathi, Akansha; Hernández, M.; Dierkes, Wilma K.; Bergmann, C.; Noordermeer, Jacobus W.M.; Trimbach, J.; Blume, Anke

    2015-01-01

    In this study, the effect of Treated Distillate Aromatic Extract (TDAE) was investigated in medium styrene/high vinyl solution styrene butadiene rubber (S-SBR) and high cis-polybutadiene rubber (BR). Three properties were evaluated: (i) molecular structure (polarity/aromaticity), (ii) molecular

  10. Structure–property relationships of ‘safe’ aromatic oil based passenger car tire tread rubber compounds

    NARCIS (Netherlands)

    Rathi, Akansha; Hernández, M.; Dierkes, Wilma K.; Bergmann, C.; Trimbach, J.; Blume, Anke

    2016-01-01

    In this study, the effect of TDAE-oil was investigated in functionalized, medium styrene/high vinyl solution styrene butadiene rubber (FsS-SBR) and high cispolybutadiene rubber (BR). Three properties were evaluated: (i) molecular structure (polarity/aromaticity), (ii) molecular weight and (iii)

  11. Effect of electron beam irradiation on the properties of natural rubber (NR)/styrene-butadiene rubber (SBR) blend

    Energy Technology Data Exchange (ETDEWEB)

    Manshaie, R. [Department of Chemical Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Nouri Khorasani, S., E-mail: saied@cc.iut.ac.i [Department of Chemical Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Jahanbani Veshare, S. [Department of Chemical Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Rezaei Abadchi, M. [Department of Polymer Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of)

    2011-01-15

    In this study, physico-mechanical properties of NR/SBR blends cured by electron beam irradiation and sulfur were compared. The NR/SBR blends were prepared using a two-roll mill. Electron beam irradiations of 100-400 kGy were applied to cure the blends and changes in physico-mechanical properties were studied as a function of irradiation. Also, oil resistance and the effect of thermal ageing on mechanical properties of the blends were investigated. The results show that the irradiated blends have better mechanical properties than those cured by sulfur system. The irradiation cured samples also exhibited better heat stability than the sulfur cured samples. The blend cured by the highest dose shows the lowest swelling and high oil resistance compared with the other samples cured by irradiation.

  12. Effect of electron beam irradiation on the properties of natural rubber (NR)/styrene-butadiene rubber (SBR) blend

    Science.gov (United States)

    Manshaie, R.; Nouri Khorasani, S.; Jahanbani Veshare, S.; Rezaei Abadchi, M.

    2011-01-01

    In this study, physico-mechanical properties of NR/SBR blends cured by electron beam irradiation and sulfur were compared. The NR/SBR blends were prepared using a two-roll mill. Electron beam irradiations of 100-400 kGy were applied to cure the blends and changes in physico-mechanical properties were studied as a function of irradiation. Also, oil resistance and the effect of thermal ageing on mechanical properties of the blends were investigated. The results show that the irradiated blends have better mechanical properties than those cured by sulfur system. The irradiation cured samples also exhibited better heat stability than the sulfur cured samples. The blend cured by the highest dose shows the lowest swelling and high oil resistance compared with the other samples cured by irradiation.

  13. Treatment of wastewater from rubber industry in Malaysia ...

    African Journals Online (AJOL)

    Presently, Malaysia is the third largest rubber producer in the world, whereby the rubber industry is an economically and socially significant industry. Rubber industry consumes large volumes of water, uses chemicals and other utilities and produces enormous amounts of wastes and effluent. Discharge of untreated rubber ...

  14. Influence of notch depth on tearing morphology and tearing energy in carbon-black-loaded SBR (styrene butadiene rubber)

    Energy Technology Data Exchange (ETDEWEB)

    Goldberg, A.; LeMay, J.D.; Sanchez, R.J.; Stone, J.C.; Patt, J.

    1987-01-30

    Tearing energies (T) have been evaluated for carbon-black-reinforced SBR tested in uniaxial tension. The influence of notch depth on T and fracture morphology have also been determined. The influence of notch depth on the stress-strain behavior and on the failure stress and failure strain is also illustrated. The ratio of recovered-to-input energy as a function of both stress and strain was determined for notched and notch-free samples.

  15. Preparation, characterization, dielectric properties and diffusion studies of styrene butadiene rubber (SBR)/manganous tungstate (MnWO4) nanocomposites

    Science.gov (United States)

    Jasna, V. C.; Ramesan, M. T.

    2017-06-01

    Nanocomposites based on SBR with different content of manganous tungstate nanoparticles were prepared and characterized by FTIR, UV-visible spectroscopy, XRD, SEM, TGA, DSC and impedance analysis. The interaction between nanoparticles and the elastomer was clear from the shift in peaks of UV and FTIR. XRD and SEM analysis showed the uniform arrangement of nanoparticles in SBR matrix. Glass transition temperature, thermal stability and dielectric properties of composites were enhanced by the addition of nanoparticles. Sorption studies of nanocomposites were done in aromatic solvents at different temperature. Sorption data obtained were used to estimate the thermodynamic properties.

  16. Federal Specification MMM-A-1617B for Adhesive, Rubber-Base, General-Purpose HAP-Free Replacement

    Science.gov (United States)

    2011-05-01

    classified into three types (3): • Type I: Non-oil-resistant natural rubber base, synthetic natural (polyisoprene), styrene butadiene (SBR), reclaim...or combinations. • Type II: Oil-resistant polychloroprene rubber base. • Type III: Fuel-resistant butadiene acrylonitrile (nitrile) rubber base...all contained a nitrile polymer base, also known as acrylonitrile butadiene . Nitrile has good resistance to oil, water, and heat. The adhesive

  17. Preparation, characterization and evaluation of proton-conducting hybrid membranes based on sulfonated hydrogenated styrene-butadiene and polysiloxanes for fuel cell applications

    Energy Technology Data Exchange (ETDEWEB)

    Monroy-Barreto, M.; Aguilar, J.C.; Rodriguez de San Miguel, E.; de Gyves, J. [Departamento de Quimica Analitica, Facultad de Quimica, UNAM, Ciudad Universitaria, 04360 Mexico, D.F. (Mexico); Acosta, J.L.; del Rio, C.; Ojeda, M.C. [Instituto de Ciencia y Tecnologia de Polimeros (CSIC), c/Juan de la Cierva 3, 28006 Madrid (Spain); Munoz, M. [Departament de Quimica Analitica, Facultat de Ciencies, U.A.B., Bellaterra 08193 Barcelona (Spain)

    2010-12-15

    This paper describes the preparation of proton-conducting hybrid membranes (HMs) obtained by a solvent casting procedure using a solution containing sulfonated hydrogenated styrene-butadiene (HSBS-S) and an inorganic-organic mixture (polysiloxanes) previously prepared by a sol-gel route. HSBS-S copolymers with different sulfonation degrees were obtained and characterized by means of elemental analysis (EA), chemical titration and electrochemical impedance spectroscopy (EIS). HSBS-S with the best properties in terms of proton conductivity and solubility for the casting procedure was selected to prepare the HMs. The solvent casting procedure permitted the two phases to be homogeneously distributed while maintaining a relatively high proton conductivity in the membrane. HMs with different blend ratios were characterized using structural (Fourier transform infrared-attenuated total reflectance (FTIR-ATR), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC)), electrical (EIS), physicochemical (water uptake, ion-exchange capacity) and thermal (TGA-MS) methods. Finally, the optimized HSBS-S membrane and HMs were tested in hydrogen single fuel cells to obtain the polarization and power curves at different cell temperatures and gas pressures. Results indicate that HMs show a considerable improvement in performance compared to the optimized HSBS-S membrane denoting the benefit of incorporating the inorganic-organic network in the hydrogenated styrene-butadiene matrix. A Nafion membrane was used as reference material throughout this work. (author)

  18. A new mechanism for selective adsorption of rubber on carbon black surface caused by nano-confinement in SBR/NBR solution

    Science.gov (United States)

    Kawazoe, Masayuki

    A novel mechanism of selective adsorption of rubber molecules onto carbon black surface in a binary immiscible rubber blend solution has been proposed in this dissertation. The phenomenon leads to uneven distribution of carbon black to the specific polymer in the blend and the obtained electrically conductive composite showed drastic reduction of percolation threshold concentration (PTC). The mechanism and the feature of conductive network formation have much potential concerning both fundamental understanding and industrial application to improve conductive polymer composites. In chapter I, carbon black filled conductive polymer composites are briefly reviewed. Then, in chapter II, a mechanism of rubber molecular confinement into carbon black aggregate structure is introduced to explain the selective adsorption of a specific rubber onto carbon black surface in an immiscible rubber solution blend (styrene butadiene rubber (SBR) and acrylonitrile butadiene rubber (NBR) with toluene or chloroform). Next, in chapters III and IV, polymers with various radius of gyration (Rg) and carbon blacks with various aggregate structure are examined to verify the selective adsorption mechanism. Finally, in chapter V, the novel mechanism was applied to create unique meso-/micro-unit conductive network in carbon black dispersed SBR/NBR composites.

  19. Predicting the glass transition temperature as function of crosslink density and polymer interactions in rubber compounds

    Science.gov (United States)

    D'Escamard, Gabriella; De Rosa, Claudio; Auriemma, Finizia

    2016-05-01

    Crosslink sulfur density in rubber compounds and interactions in polymer blends are two of the composition elements that affect the rubber compound properties and glass transition temperature (Tg), which is a marker of polymer properties related to its applications. Natural rubber (NR), butadiene rubber (BR) and styrene-butadiene rubber (SBR) compounds were investigated using calorimetry (DSC) and dynamic mechanical analysis (DMA). The results indicate that the Di Marzio's and Schneider's Models predict with accuracy the dependence of Tg on crosslink density and composition in miscible blends, respectively, and that the two model may represent the base to study the relevant "in service" properties of real rubber compounds.

  20. Elastomers for Tracked Vehicles: 1980-1997 Program to Improve Durability of Rubber Tank Pads for Army Tracked Vehicles

    Science.gov (United States)

    2015-06-01

    into more stable single bonds. Because of the reduction in double bonds, HNBR provides superior resistance to ozone , weathering, and heat when compared...PBD-2. Synpol E-BR 8418 (containing 20 parts of high aromatic oil ) and Nipol BR-1245 BRs were used in formulations PBD-5 and PBD-8, respectively...methods for rubber-evaluation of SBR (styrene-butadiene rubber) including mixtures with oil . West Conshohocken (PA): ASTM International; 2010. ASTM D

  1. High Performance Graphene Oxide Based Rubber Composites

    OpenAIRE

    Yingyan Mao; Shipeng Wen; Yulong Chen; Fazhong Zhang; Pierre Panine; Tung W. Chan; Liqun Zhang; Yongri Liang; Li Liu

    2013-01-01

    In this paper, graphene oxide/styrene-butadiene rubber (GO/SBR) composites with complete exfoliation of GO sheets were prepared by aqueous-phase mixing of GO colloid with SBR latex and a small loading of butadiene-styrene-vinyl-pyridine rubber (VPR) latex, followed by their co-coagulation. During co-coagulation, VPR not only plays a key role in the prevention of aggregation of GO sheets but also acts as an interface-bridge between GO and SBR. The results demonstrated that the mechanical prope...

  2. Elimination of the reactivation process in the adhesion of chlorinated SBS rubber with polychloroprene adhesives

    Directory of Open Access Journals (Sweden)

    2007-04-01

    Full Text Available Chlorination treatment of a thermoplastic styrene-butadiene-styrene rubber (SBS with a 3 wt% solution of trichloroisocyanuric acid (TCI in methyl ethyl ketone (MEK introduces chlorinated and oxidized moieties on the rubber surface which increase its surface energy and produces surface microroughness. Consequently adhesion properties, evaluated by T-peel strength measurements in chlorinated SBS/solvent based-polyurethane adhesive/leather joints, are enhanced. In this study, two solvent-based polychloroprene adhesives (PCP0 and PCP30R have been considered as an alternative to the commonly used solvent-based polyurethane adhesive (PU. A thermoreactive phenolic resin was added to one of the polychloroprene adhesive formulations (PCP30R. This tackifier resin favors chlorination of the adhesive and reinforces the interface between the chlorinated adhesive and the chlorinated rubber surface. Besides, PCP30R adhesive does not need adhesive reactivation and considerable high T-peel strength value (5.7±0.3 kN/m was obtained. Elimination of the reactivation process implies a considerable improvement of the manufacturing process in the footwear industry.

  3. The performance and risk of Kossan Rubber Industries Berhad

    OpenAIRE

    teoh, kun youn

    2017-01-01

    The purpose of the study is to investigate the overall performance of Kossan Rubber Industries Bhd with internal factors and external factors on profitability performance. The data obtained from annual report of Kossan Rubber Industries Bhd during the years 2011 to 2015. The financial ratio used to measure the overall performance and risk of the company. The measurement of current ratio, return on assets (ROA), and inventory turnover are used to determine the overall performance and the effic...

  4. Multilayer graphene rubber nanocomposites

    Science.gov (United States)

    Schartel, Bernhard; Frasca, Daniele; Schulze, Dietmar; Wachtendorf, Volker; Krafft, Bernd; Morys, Michael; Böhning, Martin; Rybak, Thomas

    2016-05-01

    Multilayer Graphene (MLG), a nanoparticle with a specific surface of BET = 250 m2/g and thus made of only approximately 10 graphene sheets, is proposed as a nanofiller for rubbers. When homogenously dispersed, it works at low loadings enabling the replacement of carbon black (CB), increase in efficiency, or reduction in filler concentration. Actually the appropriate preparation yielded nanocomposites in which just 3 phr are sufficient to significantly improve the rheological, curing and mechanical properties of different rubbers, as shown for Chlorine-Isobutylene-Isoprene Rubber (CIIR), Nitrile-Butadiene Rubber (NBR), Natural Rubber (NR), and Styrene-Butadiene Rubber (SBR). A mere 3 phr of MLG tripled the Young's modulus of CIIR, an effect equivalent to 20 phr of carbon black. Similar equivalents are observed for MLG/CB mixtures. MLG reduces gas permeability, increases thermal and electrical conductivities, and retards fire behavior. The later shown by the reduction in heat release rate in the cone calorimeter. The higher the nanofiller concentration is (3 phr, 5 phr, and 10 phr was investigated), the greater the improvement in the properties of the nanocomposites. Moreover, the MLG nanocomposites improve stability of mechanical properties against weathering. An increase in UV-absorption as well as a pronounced radical scavenging are proposed and were proved experimentally. To sum up, MLG is interesting as a multifunctional nanofiller and seems to be quite ready for rubber development.

  5. Genotoxic risk in rubber manufacturing industry: a systematic review.

    Science.gov (United States)

    Bolognesi, Claudia; Moretto, Angelo

    2014-10-15

    A large body of evidence from epidemiological studies among workers employed in the rubber manufacturing industry has indicated a significant excess cancer risk in a variety of sites. The International Agency for Research on Cancer has recently classified the "Occupational exposures in the rubber-manufacturing industry" as carcinogenic to humans (Group 1). A genotoxic mechanism for the increased cancer risk was suggested on the basis of the evidence from the scientific literature. Exposure assessment studies have shown that workers in the rubber manufacturing industry may be exposed to different airborne carcinogenic and/or genotoxic chemicals, such as certain aromatic amines, polycyclic aromatic hydrocarbons, N-nitrosamines, although the available information does not allow to establish a causal association of cancer or genotoxic risk with particular substances/classes of chemicals or specific jobs. The aim of this paper is to critically evaluate, by conducting a systematic review, the available biomonitoring studies using genotoxicity biomarkers in rubber manufacturing industry. This systematic review suggests that a genotoxic hazard may still be present in certain rubber manufacturing industries. A quantitative risk assessment needs further studies addressing the different, processes and chemicals in the rubber manufacturing industries. Copyright © 2013 Elsevier Ireland Ltd. All rights reserved.

  6. DFT studies of the effectiveness of p-substituted diphenyl amine antioxidants in styrene-butadiene rubber through their Cu(II) coordination ability

    Science.gov (United States)

    Puškárová, Ingrid; Breza, Martin

    2017-07-01

    Structures of a series of diphenyl amine (DPA) antioxidants and of their complexes with Cu2+ were optimized at B3LYP level of theory. DPAs may be divided into two groups according to their molar antioxidant effectiveness (AEM). The effectiveness of high-AEM DPA antioxidants at 130 °C rises with decreasing spin densities at Cu atoms and with the increasing electron density Laplacian at Cu-N bond critical points in the 2[DPA…Cu]2+ complexes similarly as in the case of p-phenylene diamine antioxidants. No such trends are observed at 25 °C and for low- AEM DPA antioxidants.

  7. Toxicity of the components of styrene polymers: polystyrene, acrylonitrile-butadiene-styrene (ABS) and styrene-butadiene-rubber (SBR). Reactants and additives.

    Science.gov (United States)

    Fishbein, L

    1984-01-01

    The toxicity of the components of styrene polymers, e.g., polystyrene, ABS and SBR, were reviewed with primary focus on the reactive monomers (except styrene) (e.g., acrylonitrile, butadiene) as well as on impurities and solvents such as benzene, hexane and methylethyl ketone, and additives such as phenyl-2-naphthylamine, di-n-butyl phthalate, and a number of peroxide initiators and flame retardants (e.g., 2,3-dibromopropanol, decadibromodiphenyl oxide and antimony trioxide). It is stressed that toxicity data are generally lacking for the majority of additives employed in the production of styrene polymers. Information is also lacking as to the numbers of individuals at potential risk and the extent of their exposure to the large number of additives employed.

  8. Mechanical Properties and Vulcanization Characteristics of Styrene-Butadiene Rubber (sbr) Based Compounds Filled with Eggshell Powder as a Bio-Filler

    Science.gov (United States)

    Saeb, Mohammad Reza; Dakhel, Hadi Ramezani; Ghaffari, Akbar

    2008-08-01

    Egg shell is an ordered bioceramic composite with five different layers [1, 2]. In this study, the effect of using various types of eggshell powder including after and before hatching eggshell and boiled eggshell on the mechanical properties and vulcanization characteristics of SBR compounds has been investigated. The obtained results were compared with calcium carbonate filled compounds. Evaluation of mechanical properties exhibited that incorporation of eggshell increased almost all of the mechanical properties of the compounds. BET test demonstrated higher specific area of eggshell powders compare with calcium carbonate. Some of the observed results attributed to higher specific area of eggshell powder. However, there is no definitive reason for some other results at this time. Vulcanization characteristics of the compounds showed that incorporation of eggshell powder had no considerable effect on curing time. The results of this research showed that all kinds of eggshell powders can be used in SBR based compounds successfully.

  9. Treatment of wastewater from rubber industry in Malaysia

    African Journals Online (AJOL)

    GREGORY

    2010-09-20

    Sep 20, 2010 ... Review. Treatment of wastewater from rubber industry in. Malaysia. Mitra Mohammadi1, Hasfalina Che Man2*, Mohd Ali Hassan1 and Phang Lai Yee1. 1Department of Bioprocess Technology, Faculty of Biotechnology and Biomolecular Sciences, Universiti Putra Malaysia, 43400. UPM Serdang, Selangor ...

  10. Adhesion strength study between plasma treated polyester fibres and a rubber matrix

    Science.gov (United States)

    Krump, H.; Šimor, M.; Hudec, I.; Jaššo, M.; Luyt, A. S.

    2005-02-01

    In this work, the adhesion strength between poly(ethylene terephthalate) (PET) fibres and styrene-butadiene rubber (SBR) was studied. The effects of atmospheric plasma treatment, used to increase adhesion strength between PET fibres and the rubber matrix, were investigated and compared. It was confirmed that lubricants on the fibres caused a decrease in adhesion strength between the plasma treated reinforcing PET fibres and the SBR rubber matrix. These lubricants can be removed by acetone. When washed and treated in plasma, a substantial improvement in adhesion strength was observed. No ageing in air before combination with the rubber matrix was observed. This confirmed that the plasma streamers caused the creation of a new, relatively stable chemical species on the polymer surface. It suggests that the surface modification of PET fibres by plasma treatment at atmospheric gas pressure is a suitable and technologically applicable method for the improvement of adhesion strength of polyester reinforcing materials to rubber.

  11. Hyundai plans rubber unit despite overcapacity

    Energy Technology Data Exchange (ETDEWEB)

    Hyoungjin Kim

    1993-02-24

    Despite the oversupply of synthetic rubber in South Korea, the government has granted approval to Hyundai Petrochemical (Seoul) to build the country's second synthetic rubber unit, to be located alongside its petrochemical complex at Daesan. The plant is due for startup during second-half 1995, when the local market is expected to be in better balance. Hyundai will use Goodyear Tire Rubber technology for the plant, which will have annual capacities for 40,000 m.t. of polybutadiene rubber (BR), 30,000 m.t. of styrene butadiene rubber (SBR) and 12,000 m.t. of nitrile rubber (NBR). Styrene and butadiene requirements will be met from Hyundai's own production at Daesan. The current local producer of synthetic rubber is Korea Kumho Petrochemicals (Seoul), which has annual capacities for 150,000 m.t. of SBR, 95,000 m.t. of BR, and 10,000 m.t. of NBR. Korean SBR demand is about 141,000 m.t./year but is expected to increase to 161,000 m.t./year by 1996 and reach 194,000 m.t./year by the end of the decade.

  12. 29 CFR 1910.216 - Mills and calenders in the rubber and plastics industries.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 5 2010-07-01 2010-07-01 false Mills and calenders in the rubber and plastics industries. 1910.216 Section 1910.216 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND... Guarding § 1910.216 Mills and calenders in the rubber and plastics industries. (a) General requirements— (1...

  13. Measurement of Noise Level in Enumeration Station in Rubber Industry

    Science.gov (United States)

    Rizkya, I.; Syahputri, K.; Sari, R. M.; Siregar, I.

    2017-03-01

    This research was conducted in companies engaged in the production of crumb rubber. In the rubber industry, the potential noise occurs in the enumeration station. Stations enumeration use machine and equipment that potentially generated noise. Noise can be defined as an unwanted sound because it does not fit the context of space and time so that may interfere with the comfort and human health. The noise level measured at random during the initial observation station enumeration is 101.8 dB. This value has exceeded the Threshold Limit Value (TLV) Kep-51 / MEN / 1999 and SNI No. 16-7063-2004 so research must be done to measure the level of noise in the enumeration station. Quantitative methods used in the study. Observations made with the calculation method of equivalent noise level. Observations were made on six measurement points for one shift for three days. The results showed the noise level over the Threshold Limit Value is equal to 85 dBA/8 hours. Based on the measurement results, the whole point of observation was far above the threshold Limit Value (TLV). The highest noise level equivalent is in the observation point 6 with a value of 102, 21 dB.

  14. Greenhouse Gas Emissions from Rubber Industry in Thailand

    NARCIS (Netherlands)

    Jawjit, W.; Kroeze, C.; Rattanapan, S.

    2010-01-01

    Rubber production has been taking place in Thailand for many decades. Thailand is currently the world's largest natural rubber producer. We present emissions of greenhouse gases associated with the production of fresh latex, and three primary rubber products, including concentrated latex, block

  15. Effect of adding of the styrene-butadiene-styrene (SBS) copolymer in chemical and rheological properties of the brazilian asphalt; Efeito da adicao de SBS nas propriedades quimicas e reologicas de asfalto oriundo de petroleo brasileiro

    Energy Technology Data Exchange (ETDEWEB)

    Lucena, M.C.C.; Soares, S.A. [Ceara Univ., Fortaleza, CE (Brazil). Dept. de Quimica Organica e Inorganica]. E-mail: mccl@dqoi.ufc.br; sas@ufc.br; Soares, J.B. [Ceara Univ., Fortaleza, CE (Brazil). Dept. de Engenharia de Transportes]. E-mail: jsoares@det.ufc.br

    2003-07-01

    Chemical and rheological characterization of the asphalt cement (AC) from the Fazenda Alegre petroleum, and the effect of adding 4.5% of the styrene-butadiene-styrene (SBS) copolymer were investigated. Structural characteristics were analyzed by infrared spectroscopy (FTIR) and nuclear magnetic resonance (NMR). A structure similar to the Arabian and Venezuelan petroleum was observed. The simulated aging led to structural modification noticed by the increment in the carbonyl and sulphoxide groups. Thermogravimetry (TGA) showed that SBS did not affect the AC thermal decomposition at both inert and oxidative atmosphere. However, the differential scanning calorimetry (DSC) showed a decrease in the glass transition temperature of the material when SBS was added. The effect of SBS on the absolute viscosity revealed that SBS is not an inert additive and causes an increase in viscosity, in a nonlinear fashion. The commonly found Newtonian behavior of asphalt binders under high temperatures was also found on the SBS modified binder. Dynamic mechanical tests have shown that SBS increases the binder performance grade. (author)

  16. Rubber

    Science.gov (United States)

    Graves, D. F.

    The word "rubber" immediately brings to mind materials that are highly flexible and will snap back to their original shape after being stretched. In this chapter a variety of materials are discussed that possess this odd characteristics. There will also be a discussion on the mechanism of this "elastic retractive force." Originally, rubber meant the gum collected from a tree growing in Brazil. The term "rubber" was coined for this material by the English chemist Joseph Priestley, who noted that it was effective for removing pencil marks from paper. Today, in addition to Priestley's natural product, many synthetic materials are made that possess these characteristics and many other properties. The common features of these materials are that they are made up of long-chain molecules that are amorphous (not crystalline), and the chains are above their glass transition temperature at room temperature.

  17. Volume Changes in Filled Rubber Under Uniaxial Cyclic Loading

    Directory of Open Access Journals (Sweden)

    Elina KAZINA

    2011-09-01

    Full Text Available Styrene-butadiene rubber, neat and filled with different silica content was investigated under uniaxial cyclic loading under a constant crosshead speed, with increasing deformation amplitude in subsequent loading cycles. Rubber was investigated in order to evaluate the reversibility of structure rearrangements, occurring in rubber when subjected to cyclic loading. Volume uniformly increases with growing strain and shows hysteresis at unloading. After complete unloading, no residual strain changes are observed. These data are in good conformity with the data of density measurements, which were made on specimens before and after the tests. By correlating data, obtained from volume changes and kinetics of hysteresis losses there were made assumptions on deformation mechanisms at different elongations. Deformational mechanisms, responsible for volume changes in rubber are reversible. Volume changes in specimen occur due to voids formation caused by filler microstructure breakage, rubber chains disentanglement, spaces between rubber macromolecular chains shrinkage, and chain slippage under higher elongations. Voids formation and deformation of rubber macromolecular chain reaches equilibrium state after certain elongation.http://dx.doi.org/10.5755/j01.ms.17.3.592

  18. Performance evaluation of CFRP-rubber shock absorbers

    Energy Technology Data Exchange (ETDEWEB)

    Lamanna, Giuseppe, E-mail: giuseppe.lamanna@unina2.it; Sepe, Raffaele, E-mail: giuseppe.lamanna@unina2.it [Department of Industrial and Information Engineering, Second University of Naples, via Roma, 29 - 81031 Aversa (Italy)

    2014-05-15

    In the present work a numerical investigation on the energy absorbing capability of dedicated structural components made of a carbon fiber reinforced polymer and an emulsion polymerised styrene butadiene rubber is reported. The shock absorbers are devices designed to absorb large amounts of energy by sacrificing their own structural integrity. Their aim is to cushion the effects of an impact phenomenon with the intent to preserve other structures from global failure or local damaging. Another important role of shock absorbers is reducing the peak of the acceleration showed during an impact phenomenon. This effect is of considerable interest in the case of vehicles to preserve passengers’ safety. Static and dynamic numerical results are compared with experimental ones in terms of mean crushing forces, energy and peak crushing. The global performance of the absorbers has been evaluated by referencing to a proposed quality index.

  19. Performance evaluation of CFRP-rubber shock absorbers

    Science.gov (United States)

    Lamanna, Giuseppe; Sepe, Raffaele

    2014-05-01

    In the present work a numerical investigation on the energy absorbing capability of dedicated structural components made of a carbon fiber reinforced polymer and an emulsion polymerised styrene butadiene rubber is reported. The shock absorbers are devices designed to absorb large amounts of energy by sacrificing their own structural integrity. Their aim is to cushion the effects of an impact phenomenon with the intent to preserve other structures from global failure or local damaging. Another important role of shock absorbers is reducing the peak of the acceleration showed during an impact phenomenon. This effect is of considerable interest in the case of vehicles to preserve passengers' safety. Static and dynamic numerical results are compared with experimental ones in terms of mean crushing forces, energy and peak crushing. The global performance of the absorbers has been evaluated by referencing to a proposed quality index.

  20. Studies on the rubber phase stability in gamma irradiated polystyrene-SBR blends by using FT-IR and Raman spectroscopy[Gamma irradiation; Polystyrene-SBR blends; Izod impact; FTIR; Raman

    Energy Technology Data Exchange (ETDEWEB)

    Martinez-Barrera, G.; Lopez, H.; Castano, V.M.; Rodriguez, R. E-mail: rogelior@servidor.unam.mx

    2004-02-01

    Improvement in the impact properties of polystyrene-SBR blends produced by different concentrations and types of styrene-butadiene rubber (SBR) was studied. The samples were gamma irradiated at different doses to achieve good adhesion, and consequently good stability, between the rubbery phase and the polystyrene matrix, producing an improvement in the impact properties. The results show that the best Izod impact was obtained for a blend with 10% SBR and with a dose of 100 kGy. Several samples with 0%, 3%, 5% and 10% of SBR were prepared and characterized by FT-IR and FT-Raman spectroscopies.

  1. Influence of different curing systems on the physico-mechanical properties and stability of SBR and NR rubbers

    CERN Document Server

    Basfar, A A; Mofti, S

    2002-01-01

    The physical properties of radiation, sulfur and peroxide-cured styrene-butadiene rubber (SBR) and natural rubber (NR) were compared. The dependence of the mechanical properties of the radiation-vulcanized SBR and NR on the coagent concentration and radiation dose was studied. The effect of thermal aging on the mechanical properties of the different rubber formulations was discussed. The radiation-cured formulations of SBR have superior mechanical properties and thermal stability compared with those of the chemically vulcanized compounds. Whereas, the radiation-cured formulations of NR have similar mechanical properties but superior thermal stability (based on the % change in E after thermal aging), when compared with those of the sulfur-vulcanized compounds and slightly better than those of the peroxide-vulcanized compounds.

  2. Biological Reclaiming of Recycled Rubber and Its Effect on Mechanical Properties of New Rubber Vulcanizates

    Directory of Open Access Journals (Sweden)

    Maryam Mansourirad

    2014-12-01

    Full Text Available Nowadays, due to environmental concerns, there has been great attention to recycling and reclaiming of tires. Different methods have been used for reclaiming or desulfurization of rubber. One of these methods, in which desulfurization of rubber happens with no damage to the polymer structure, is desulfurization by biological microorganisms. In this research the application and performance of thermophilic and sulfur oxidizing bacteria, Acidianus brierleyi for this purpose was investigated. Ground tire rubber was detoxified with organic solvents, and the optimum conditions for growing microorganisms in the existence of rubber powder in the shaker flasks were determined. In order to accelerate the process, the suitable conditions for growth of bacteria and desulfurization in the bioreactor were adopted. Fourier transfer infrared spectroscopy and scanning electron microscopy were employed to characterize desulfurization of bio-treated powder from bioreactor. The results indicated that morphological changes on powder surface and reduction of sulfur bonds have occurred. Samples from bioreactors, with and without bacteria and also untreated rubber powder were compounded with virgin styrene butadiene rubber. Tensile and dynamic properties were investigated using uni-direction tensile test and dynamic-mechanical-thermal analysis, respectively. Although some differences in dynamic-mechanical-thermal properties of samples pointed to stronger interaction between rubber matrix and treated rubber powder, no significant improvements in the mechanical properties of vulcanizates containing A.brierleyi-treated powder were observed. Low concentration of sulfur in rubber vulcanizates, chemical bonds of sulfur, and low efficiency of A. brierleyi in breaking sulfur bonds and reclaiming rubber were considered as the reasons for low efficiency of this treatment process.

  3. Reinforcement of SBR/waste rubber powder vulcanizate with in situ generated zinc dimethacrylate

    Science.gov (United States)

    Wang, X. P.; Cheng, B. K.; Zhang, X.; Jia, D. M.

    2016-07-01

    Methyl acrylic acid/zinc oxide (MAA/ZnO) was introduced to modify styrene- butadiene rubber/waste rubber powder (SBR/WRP) composites by blending. The enhanced mechanical properties and processing ability were presumably originated from improved compatibility and interfacial interaction between WRP and the SBR matrix by the in situ polymerization of zinc dimethacrylate (ZDMA). A refined interface of the modified SBR/WRP composite was observed by scanning electron microscopy. The formation of ZDMA significantly increased the ionic bond content in the vulcanizate, resulting in exceptional mechanical performance. The comprehensive mechanical properties including tensile strength, tear strength and dynamic heat-building performance reached optimum values with 16 phr MAA.

  4. High Performance Graphene Oxide Based Rubber Composites

    Science.gov (United States)

    Mao, Yingyan; Wen, Shipeng; Chen, Yulong; Zhang, Fazhong; Panine, Pierre; Chan, Tung W.; Zhang, Liqun; Liang, Yongri; Liu, Li

    2013-08-01

    In this paper, graphene oxide/styrene-butadiene rubber (GO/SBR) composites with complete exfoliation of GO sheets were prepared by aqueous-phase mixing of GO colloid with SBR latex and a small loading of butadiene-styrene-vinyl-pyridine rubber (VPR) latex, followed by their co-coagulation. During co-coagulation, VPR not only plays a key role in the prevention of aggregation of GO sheets but also acts as an interface-bridge between GO and SBR. The results demonstrated that the mechanical properties of the GO/SBR composite with 2.0 vol.% GO is comparable with those of the SBR composite reinforced with 13.1 vol.% of carbon black (CB), with a low mass density and a good gas barrier ability to boot. The present work also showed that GO-silica/SBR composite exhibited outstanding wear resistance and low-rolling resistance which make GO-silica/SBR very competitive for the green tire application, opening up enormous opportunities to prepare high performance rubber composites for future engineering applications.

  5. High Performance Graphene Oxide Based Rubber Composites

    Science.gov (United States)

    Mao, Yingyan; Wen, Shipeng; Chen, Yulong; Zhang, Fazhong; Panine, Pierre; Chan, Tung W.; Zhang, Liqun; Liang, Yongri; Liu, Li

    2013-01-01

    In this paper, graphene oxide/styrene-butadiene rubber (GO/SBR) composites with complete exfoliation of GO sheets were prepared by aqueous-phase mixing of GO colloid with SBR latex and a small loading of butadiene-styrene-vinyl-pyridine rubber (VPR) latex, followed by their co-coagulation. During co-coagulation, VPR not only plays a key role in the prevention of aggregation of GO sheets but also acts as an interface-bridge between GO and SBR. The results demonstrated that the mechanical properties of the GO/SBR composite with 2.0 vol.% GO is comparable with those of the SBR composite reinforced with 13.1 vol.% of carbon black (CB), with a low mass density and a good gas barrier ability to boot. The present work also showed that GO-silica/SBR composite exhibited outstanding wear resistance and low-rolling resistance which make GO-silica/SBR very competitive for the green tire application, opening up enormous opportunities to prepare high performance rubber composites for future engineering applications. PMID:23974435

  6. FTIR spectra and mechanical strength analysis of some selected rubber derivatives

    Science.gov (United States)

    Gunasekaran, S.; Natarajan, R. K.; Kala, A.

    2007-10-01

    Rubber materials have wide range of commercial applications such as, infant diapers, famine hygiene products, drug delivery devices and incontinency products such as rubber tubes, tyres, etc. In the present work, studies on mechanical properties of some selected rubber materials viz., natural rubber (NR), styrene butadiene rubber (SBR), nitrile butadiene rubber (NBR) and ethylene propylene diene monomer (EPDM) have been carried out in three states viz., raw, vulcanized and reinforced. To enhance the quality of rubber elastomers, an attempt is made to prepare new elastomers called polyblends. In the present study an attempt is made to blend NR with NBR and with EPDM. We here report, a novel approach for the evaluation of various physico-mechanical properties such as mechanical strength, tensile strength, elongation and hardness. The method is simple, direct and fast and involves infrared spectral measurements for the evaluation of these properties. With the applications of modern infrared spectroscopy, the mechanical strength of these rubber materials have been analyzed by calculating the internal standards among the methyl and methylene group vibrational frequencies obtained from FTIR spectroscopy. Also the tensile strength measurements carried out by universal testing machine. The results pertaining physico-mechanical properties of the rubber derivatives undertaken in the present study obtained by IR-based method are in good agreement with data resulted from the standard methods.

  7. New insights into the effects of styrene-butadiene-styrene polymer modifier on the structure, properties, and performance of asphalt binder: The case of AP-5 asphalt and solvent deasphalting pitch

    Energy Technology Data Exchange (ETDEWEB)

    Nciri, Nader, E-mail: nader.nciri@koreatech.ac.kr [Department of Energy, Materials, and Chemical Engineering, Korea University of Technology and Education, 1600 Chungjeol-ro, Byeongcheon-myeon, Dongnam-gu, Cheonan-City, Chungnam-Province 330-708 (Korea, Republic of); Kim, Namho [Department of Architectural Engineering, Korea University of Technology and Education, 1600 Chungjeol-ro, Byeongcheon-myeon, Dongnam-gu, Cheonan-City, Chungnam-Province 330-708 (Korea, Republic of); Cho, Namjun, E-mail: njuncho@koreatech.ac.kr [Department of Energy, Materials, and Chemical Engineering, Korea University of Technology and Education, 1600 Chungjeol-ro, Byeongcheon-myeon, Dongnam-gu, Cheonan-City, Chungnam-Province 330-708 (Korea, Republic of)

    2017-06-01

    This paper deals with the poorly understood effects of styrene-butadiene-styrene (SBS) copolymer on the bitumen performance. It focuses on determining the impact of various concentrations (e.g., 0, 4, 8, and 12 wt. %) of SBS on the attributes of two types of asphalt namely AP-5 asphalt and solvent deasphalting (SDA) pitch. The unmodified and modified binders were investigated in terms of their chemical compositions, microstructures, thermo-analytical behaviors, and physical properties. The intricate chemical compositions were evaluated by elemental analysis and thin layer chromatography-ionization detection (TLC-FID). Fourier transform infrared (FT-IR) and nuclear magnetic resonance (NMR) spectroscopies, scanning electron microscopy (SEM), and X-ray diffraction (XRD) were utilized to examine the microstructures. Whereas, thermal characteristics were evaluated by thermogravimetric analysis (TGA/DTGA) and differential scanning calorimetry (DSC). The physical behaviors were monitored through the softening point, penetration, viscosity, and ductility tests. The findings showed that the blending of asphalt with different amounts of SBS resulted into different rheological behaviors. This was reflected from the difference in the SARA (i.e., saturates, aromatics, resins, and asphaltenes) compositions and colloidal instability indexes of the modified asphalts. SEM exhibited a continuous asphalt phase with distributed SBS particles, a continuous polymer phase with distributed asphalt globules, or two interconnected continuous phases. FT-IR, {sup 1}H {sup 13}C NMR, and XRD data revealed that the AP-5 asphalt and SDA pitch experienced a number of distinct structural changes. TGA/DSC studies determined the occurrence of diverse events during thermal treatment. It is concluded that the degree of SBS modification depends strongly on SARA composition and polymer content. If the polymers are molded at higher concentrations along with aromatics-rich SDA pitches, then the mixtures

  8. Pengaruh pupuk organik limbah padat industri crumb rubber terhadap pertumbuhan tanaman cabe (Capsicum frutescens

    Directory of Open Access Journals (Sweden)

    Supraptiningsih

    2010-06-01

    Full Text Available Abstract The research about the influence of organic fertilizer of crumb rubber solid waste industry on chili plants (capsicum frutescens growth had been done. The aim of the research was to evaluate the vegetative growth of chili plants treated with organic fertilizer that was made from crumb rubber solid waste industry and it was compared with chili plants treated was commercial organic fertilizer (SP -36. The organic fertilizer was made by mixing of soil, crumb rubber solid waste, cow fieces, talc, saw dust, and hull rices, using and aerab system. The variation of the amount of solid waste was 0%; 10%, 20%; 30%; and 40%, respectively. Fertilizing of chili plants was done by dasage variation i.e.1:1,5; and 2 kg/10m2 and control (without fertilizer respectively. The observation was done on fourth month on vegetative growth including high plants, leaf length, and leaf width. The results showed that crumb rubber solid waste could be used as organic fertilizer for chili plants. The best growth of plants especially high was treated with 20% crumb rubber solid waste at dosage of 2 kg /10m2 is 38.2 cm, while the best growth of leaf length and leaf width was chili plant treated with 40% crumb rubber solid waste at dosage of 2 kg/10m2 was 10.0 cm and 6.2 cm.

  9. Plant Growth and Water Purification of Porous Vegetation Concrete Formed of Blast Furnace Slag, Natural Jute Fiber and Styrene Butadiene Latex

    Directory of Open Access Journals (Sweden)

    Hwang-Hee Kim

    2016-04-01

    Full Text Available The purpose of this study is to investigate porous vegetation concrete formed using the industrial by-products blast furnace slag powder and blast furnace slag aggregates. We investigated the void ratio, compressive strength, freeze–thaw resistance, plant growth and water purification properties using concretes containing these by-products, natural jute fiber and latex. The target performance was a compressive strength of ≥12 MPa, a void ratio of ≥25% and a residual compressive strength of ≥80% following 100 freeze–thaw cycles. Using these target performance metrics and test results for plant growth and water purification, an optimal mixing ratio was identified. The study characterized the physical and mechanical properties of the optimal mix, and found that the compressive strength decreased compared with the default mix, but that the void ratio and the freeze–thaw resistance increased. When latex was used, the compressive strength, void ratio and freeze–thaw resistance all improved, satisfying the target performance metrics. Vegetation growth tests showed that plant growth was more active when the blast furnace slag aggregate was used. Furthermore, the use of latex was also found to promote vegetation growth, which is attributed to the latex forming a film coating that suppresses leaching of toxic components from the cement. Water purification tests showed no so significant differences between different mixing ratios; however, a comparison of mixes with and without vegetation indicated improved water purification in terms of the total phosphorus content when vegetation had been allowed to grow.

  10. Determination of the Mechanical Properties of Rubber by FT-NIR

    Directory of Open Access Journals (Sweden)

    Rattapol Pornprasit

    2016-01-01

    Full Text Available Mechanical tests, for example, tensile and hardness tests, are usually used to evaluate the properties of rubber materials. In this work, mechanical properties of selected rubber materials, that is, natural rubber (NR, styrene butadiene rubber (SBR, nitrile butadiene rubber (NBR, and ethylene propylene diene monomer (EPDM, were evaluated using a near infrared (NIR spectroscopy technique. Here, NR/NBR and NR/EPDM blends were first prepared. All of the samples were then scanned using a FT-NIR spectrometer and fitted with an integration sphere working in a diffused reflectance mode. The spectra were correlated with hardness and tensile properties. Partial least square (PLS calibration models were built from the spectra datasets with preprocessing techniques, that is, smoothing and second derivative. This indicated that reasonably accurate models, that is, with a coefficient of determination [R2] of the validation greater than 0.9, could be achieved for the hardness and tensile properties of rubber materials. This study demonstrated that FT-NIR analysis can be applied to determine hardness and tensile values in rubbers and rubber blends effectively.

  11. Devulcanization of ground tire rubber: Physical and chemical changes after different microwave exposure times

    Directory of Open Access Journals (Sweden)

    P. S. Garcia

    2015-11-01

    Full Text Available Microwave devulcanization is known to be a promising and an efficient rubber recycling method which makes possible for the rubber to regain its fluidity, and makes it capable of being remolded and revulcanized. The focus of this work is to understand the physical and chemical changes that occur in the ground tire rubber after different microwave exposure periods. For this purpose chemical, thermal, rheological and morphological analyses were performed on the tire rubber, which contains natural rubber (NR and styrene-butadiene rubber (SBR as polymeric material. The results showed that the microwave treatment promoted the breaking of sulfur cross-links and consequently increased the rubber fluidity. However, long periods of exposure led to degradation and modification of some properties. At nanoscale, the deformation of the devulcanized NR domain under stress was observed, and the morphology obtained appears to be a droplet dispersion morphology. The most exposed samples presented only one glass transition temperature, and from this it was concluded that the treatment may have played an important role in the compatibilization of the elastomeric blend. Based on the results, it is required to control the microwave exposure time and polymeric degradation in order to achieve a regenerated rubber with satisfactory properties.

  12. Effect of rubber polarity on selective wetting of carbon nanotubes in ternary blends

    Directory of Open Access Journals (Sweden)

    H. H. Le

    2015-11-01

    Full Text Available Based on atomic force microscopy (AFM and Fourier transform infrared spectroscopy (FTIR analysis of the rubber-filler gel (wetting concept the kinetics of selective wetting of carbon nanotubes (CNTs in ternary styrene butadiene rubber (SBR/butadiene rubber (BR/natural rubber (NR blends was qualitatively and quantitatively characterized. Almost all CNTs are found to be wetted by the non-polar NR but not by the other non-polar rubber like BR or weakly polar SBR. It was proposed that phospholipids, which are linked to the α-terminal of NR can interact with the CNT surface through cation-π interactions forming strong bonding between NR and CNTs. Using the corrected surface tension value of NR, which involves the effect of phospholipids found in our previous work the selective wetting of CNTs in ternary rubber blends can be well predicted using the Z-model for a thermodynamic equilibrium state. By replacing the non-polar BR by a polar rubber like nitrile butadiene rubber (NBR as a blend component CNTs are wetted by NBR slightly more than by NR thanks to the strong interaction between CNTs and nitrile groups of NBR. SBR remains unbound to CNTs in both blends.

  13. Development of SBR-Nanoclay Composites with Epoxidized Natural Rubber as Compatibilizer

    Directory of Open Access Journals (Sweden)

    R. Rajasekar

    2009-01-01

    Full Text Available The significant factor that determines the improvement of properties in rubber by the incorporation of nanoclay is its distribution in the rubber matrix. The simple mixing of nonpolar rubber and organically modified nanoclay will not contribute for the good dispersion of nanofiller in the rubbery matrix. Hence a polar rubber like epoxidized natural rubber (ENR can be used as a compatibilizer in order to obtain a better dispersion of the nanoclay in the matrix polymer. Epoxidized natural rubber and organically modified nanoclay composites (EC were prepared by solution mixing. The nanoclay employed in this study is Cloisite 20A. The obtained nanocomposites were incorporated in styrene butadiene-rubber (SBR compounds with sulphur as a curing agent. The morphology observed through X-ray diffraction (XRD and high-resolution transmission electron microscopy (HR-TEM shows that the nanoclay is highly intercalated in ENR, and further incorporation of EC in SBR matrix leads to partial exfoliation of the nanoclay. Dynamic mechanical thermal analysis showed an increase in storage modulus and lesser damping characteristics for the compounds containing EC loading in SBR matrix. In addition, these compounds showed improvement in the mechanical properties.

  14. Exploration of Barriers in Achieving Proactive Environmental Strategies in a Natural Rubber Industry : A Case Study

    Directory of Open Access Journals (Sweden)

    Syarifa Arum Kusumastuti

    2016-05-01

    Full Text Available As the evolving of environmental issues over time, the development of environmental management approaches in industries began to shift to the prevention of pollution to reduce environmental impact. However, in practice, many obstacles encountered during the environmental management change to be more proactive. This study aims to explore the barriers of achieving the proactive environmental strategy in a rubber processing industry. Used a case study approach in a natural rubber processing factory, the data was collected through interviews with experts and sources as well as observation in the field. This study shows main barriers that faced by the company consist of financial issue, human resources, communities’ pressure, technological change and communication with environmental experts. The results of this study suggest conducting cooperation with research institutions or environmental experts especially for skills that cannot be controlled by the manager or employees in the company. 

  15. Quality evaluation of rubber-to-metal bonded structures based on shearography

    Science.gov (United States)

    Liu, Bin; Guo, XingMing; Qi, GongJin; Zhang, DongSheng

    2015-07-01

    The quality of bonding is often a concern in rubber-to-metal bonded parts with regard to the integrity and stability of the structure. In this study, shearography has been used to detect the out-of-plane deformation of the defects caused by thermal and vacuum stresses. A sample of the vulcanized styrene-butadiene rubber bonded to steel with known artificial voids was prepared and during bonding process a region was glued with thick adhesives. The rubber surface of the sample was inspected in thermal radiation and vacuum modes respectively with a self-designed shearography device. Meanwhile, a numerical simulation was conducted to predict the out-of-plane deformation of the rubber surface in these two stress modes. Results from the numerical simulation and the experiments indicated that the debonding defects could be inspected in both loading modes. In the thermal radiation mode the region with thick adhesives could be identified successfully. This study provides a guideline for quality control of rubber-to-metal structures using an optical method.

  16. Phase Morphology and Mechanical Properties of Cyclic Butylene Terephthalate Oligomer-Containing Rubbers: Effect of Mixing Temperature

    Directory of Open Access Journals (Sweden)

    István Zoltán Halász

    2016-08-01

    Full Text Available In this work, the effect of mixing temperature (Tmix on the mechanical, rheological, and morphological properties of rubber/cyclic butylene terephthalate (CBT oligomer compounds was studied. Apolar (styrene butadiene rubber, SBR and polar (acrylonitrile butadiene rubber, NBR rubbers were modified by CBT (20 phr for reinforcement and viscosity reduction. The mechanical properties were determined in tensile, tear, and dynamical mechanical analysis (DMTA tests. The CBT-caused viscosity changes were assessed by parallel-plate rheometry. The morphology was studied by scanning electron microscopy (SEM. CBT became better dispersed in the rubber matrices with elevated mixing temperatures (at which CBT was in partially molten state, which resulted in improved tensile properties. With increasing mixing temperature the size of the CBT particles in the compounds decreased significantly, from few hundred microns to 5–10 microns. Compounding at temperatures above 120 °C and 140 °C for NBR and SBR, respectively, yielded reduced tensile mechanical properties most likely due to the degradation of the base rubber. The viscosity reduction by CBT was more pronounced in mixes with coarser CBT dispersions prepared at lower mixing temperatures.

  17. Electrically and thermally conductive underwater acoustically absorptive graphene/rubber nanocomposites for multifunctional applications.

    Science.gov (United States)

    Li, Ying; Xu, Fan; Lin, Zaishan; Sun, Xianxian; Peng, Qingyu; Yuan, Ye; Wang, Shasha; Yang, Zhiyu; He, Xiaodong; Li, Yibin

    2017-10-05

    Graphene is ideal filler in nanocomposites due to its unique mechanical, electrical and thermal properties. However, it is challenging to uniformly distribute the large fraction of graphene fillers into a polymer matrix because graphene is not easily functionalized. We report a novel method to introduce a large fraction of graphene into a styrene-butadiene rubber (SBR) matrix. The obtained graphene/rubber nanocomposites were mechanically enhanced, acoustically absorptive under water, and electrically and thermally conductive. The Young's modulus of the nanocomposites was enhanced by over 30 times over that for rubber. The electrical conductivity of nanocomposites was ≤219 S m-1 with 15% volume fraction of graphene content, and exhibited remarkable electromagnetic shielding efficiency of 45 dB at 8-12 GHz. The thermal conductivity of the nanocomposites was ≤2.922 W m-1 k-1, which was superior to the values of thermally conductive silicone rubber thermal interface materials. Moreover, the nanocomposites exhibited excellent underwater sound absorption (average absorption coefficient >0.8 at 6-30 kHz). Notably, the absorption performance of graphene/SBR nanocomposites increased with increasing water pressure. These multifunctional graphene/SBR nanocomposites have promising applications in electronics, thermal management and marine engineering.

  18. A case-control study of bladder cancer in the United States rubber and tyre industry.

    Science.gov (United States)

    Checkoway, H; Smith, A H; McMichael, A J; Jones, F S; Monson, R R; Tyroler, H A

    1981-01-01

    A case-control study of bladder cancer was conducted in five United States rubber and tyre companies to determine if there were high-risk jobs and work areas within the industry. The study included 220 male cases of bladder cancer, of whom 107 were identified from hospital record reviews and 113 from death certificates. Each case was matched individually with two industry controls by sex, race, year of birth, and company. One control was matched additionally by year of hire and duration of employment. Comparisons of cases and controls not matched by year of hire and age of hire showed no differences for those variables, which suggests that age and calendar period of first exposure to the industry were not risk determinants. When the work histories of both cases and controls were contrasted it was found that cases were more likely than controls to have worked in milling (odds ratio (OR) = 1.91) and calender operation (OR = 2.21) jobs. The relative risk estimates for milling and calender operation both exhibited linear trends of increase with duration of exposure. Milling and calender operation jobs entail potential exposures to volatilised reaction products from heated rubber stock. A better understanding of aetiological associations with job type will require more detailed characterisation of the work environment with regard to the sources and levels of aromatic amines and other suspected bladder carcinogens. PMID:7272236

  19. Friction characteristics of 20 x 4.4, type 7, aircraft tires constructed with different tread rubber compounds

    Science.gov (United States)

    Dreher, R. C.; Yager, T. J.

    1976-01-01

    A test program was conducted at the Langley aircraft landing loads and traction facility to evaluate the friction characteristics of 20 x 4.4, type, aircraft tires constructed with experimental cut-resistant, tread rubber compounds. These compounds consisted of different blends of natural rubber (NR) and an alfin catalyzed styrene-butadiene copolymer rubber (SBR). One tire having a blend of 30 SBR and 70 NR and another having a blend of 60 SBR and 40 NR in the tread were tested together with a standard production tire with no SBR content in the tread rubber. The results of this investigation indicated that the test tires constructed with the special cut-resistant tread rubber compositions did not suffer any significant degradation in tire friction capability when compared with the standard tire. In general, tire friction capability decreased with increasing speed and surface wetness condition. As yaw angle increased, tire braking capability decreased while tire cornering capability increased. Tread-wear data based on number of brake cycles, however, suggested that the tires with alfin SBR blends experienced significantly greater wear than the standard production tire.

  20. Symptoms and immunologic markers among vulcanization workers in rubber industries in southern Sweden.

    Science.gov (United States)

    Jönsson, Lena S; Broberg, Karin; Axmon, Anna; Jönsson, Bo Ag; Littorin, Margareta

    2007-08-01

    The aim of this study was to estimate the risk of symptoms and the possible derangement of levels of immunologic markers for contemporary Swedish rubber workers. Furthermore, the relation between exposure and these biomarkers of response was examined using urinary levels of 2-thiothiazolidine-4-carboxylic acid (TTCA), which reflect the exposure. Included in the study were 166 exposed workers and 117 controls. Medical and occupational histories were obtained in structured interviews. Symptoms were recorded, and immunologic markers were analyzed in blood. Urinary levels of TTCA were determined by liquid chromatography tandem mass spectrometry. Compared with the controls, the exposed workers had increased risks of eye symptoms [odds ratio (OR) 3.0], nose bleeds (OR 4.0), burning and dry throat (OR 3.0), hoarseness (OR 2.4), severe dry cough (OR 3.8), nausea (OR 4.3), and headache (OR 2.5). When the exposed workers were divided into three groups according to the TTCA levels, the highest risks were observed among the exposed workers with intermediate TTCA levels. Furthermore, the exposed workers in all of the TTCA subgroups had elevated concentrations of total immunoglobulin G when compared with the controls. Elevated concentrations of leukocytes, neutrophils, and eosinophils were observed in the group with high TTCA levels. This work shows an increased risk of several symptoms and elevated levels of some immunologic markers among exposed workers in Swedish rubber industries. In addition, relationships between urinary levels of TTCA and some biomarkers of response were reported.

  1. An exploration study to find important factors influencing on brand in rubber industry

    Directory of Open Access Journals (Sweden)

    Mehrnaz Moshkelati

    2013-08-01

    Full Text Available Building a distinguished brand often makes it possible to have sustainable growth in competitive market. It also helps us sell products with higher price; attract reliable customers for long term relationships. This paper presents an empirical investigation to find important factors influencing rubber industry. The proposed study designs a questionnaire in Likert scale consists of 20 questions, distributes it among 300 people and collects 265 filled ones. Cronbach alpha is calculated as 0.756. In addition, Kaiser-Meyer-Olkin Measure of Sampling Adequacy and Approx. Chi-Square are 0.75 and 1292.573, respectively. Based on the results of our survey, we have derived six factors including brand transparency, expected quality, brand promises, brand support and brand sustainability.

  2. Incorporation of Rubber Powder as Filler in a New Dry-Hybrid Technology: Rheological and 3D DEM Mastic Performances Evaluation.

    Science.gov (United States)

    Vignali, Valeria; Mazzotta, Francesco; Sangiorgi, Cesare; Simone, Andrea; Lantieri, Claudio; Dondi, Giulio

    2016-10-18

    In recent years, the use of crumb rubber as modifier or additive within asphalt concretes has allowed obtaining mixtures able to bind high performances to recovery and reuse of discarded tires. To date, the common technologies that permit the reuse of rubber powder are the wet and dry ones. In this paper, a dry-hybrid technology for the production of Stone Mastic Asphalt mixtures is proposed. It allows the use of the rubber powder as filler, replacing part of the limestone one. Fillers are added and mixed with a high workability bitumen, modified with SBS (styrene-butadiene-styrene) polymer and paraffinic wax. The role of rubber powder and limestone filler within the bituminous mastic has been investigated through two different approaches. The first one is a rheological approach, which comprises a macro-scale laboratory analysis and a micro-scale DEM simulation. The second, instead, is a performance approach at high temperatures, which includes Multiple Stress Creep Recovery tests. The obtained results show that the rubber works as filler and it improves rheological characteristics of the polymer modified bitumen. In particular, it increases stiffness and elasticity at high temperatures and it reduces complex modulus at low temperatures.

  3. Incorporation of Rubber Powder as Filler in a New Dry-Hybrid Technology: Rheological and 3D DEM Mastic Performances Evaluation

    Directory of Open Access Journals (Sweden)

    Valeria Vignali

    2016-10-01

    Full Text Available In recent years, the use of crumb rubber as modifier or additive within asphalt concretes has allowed obtaining mixtures able to bind high performances to recovery and reuse of discarded tires. To date, the common technologies that permit the reuse of rubber powder are the wet and dry ones. In this paper, a dry-hybrid technology for the production of Stone Mastic Asphalt mixtures is proposed. It allows the use of the rubber powder as filler, replacing part of the limestone one. Fillers are added and mixed with a high workability bitumen, modified with SBS (styrene-butadiene-styrene polymer and paraffinic wax. The role of rubber powder and limestone filler within the bituminous mastic has been investigated through two different approaches. The first one is a rheological approach, which comprises a macro-scale laboratory analysis and a micro-scale DEM simulation. The second, instead, is a performance approach at high temperatures, which includes Multiple Stress Creep Recovery tests. The obtained results show that the rubber works as filler and it improves rheological characteristics of the polymer modified bitumen. In particular, it increases stiffness and elasticity at high temperatures and it reduces complex modulus at low temperatures.

  4. Incorporation of Rubber Powder as Filler in a New Dry-Hybrid Technology: Rheological and 3D DEM Mastic Performances Evaluation

    Science.gov (United States)

    Vignali, Valeria; Mazzotta, Francesco; Sangiorgi, Cesare; Simone, Andrea; Lantieri, Claudio; Dondi, Giulio

    2016-01-01

    In recent years, the use of crumb rubber as modifier or additive within asphalt concretes has allowed obtaining mixtures able to bind high performances to recovery and reuse of discarded tires. To date, the common technologies that permit the reuse of rubber powder are the wet and dry ones. In this paper, a dry-hybrid technology for the production of Stone Mastic Asphalt mixtures is proposed. It allows the use of the rubber powder as filler, replacing part of the limestone one. Fillers are added and mixed with a high workability bitumen, modified with SBS (styrene-butadiene-styrene) polymer and paraffinic wax. The role of rubber powder and limestone filler within the bituminous mastic has been investigated through two different approaches. The first one is a rheological approach, which comprises a macro-scale laboratory analysis and a micro-scale DEM simulation. The second, instead, is a performance approach at high temperatures, which includes Multiple Stress Creep Recovery tests. The obtained results show that the rubber works as filler and it improves rheological characteristics of the polymer modified bitumen. In particular, it increases stiffness and elasticity at high temperatures and it reduces complex modulus at low temperatures. PMID:28773965

  5. Rubber pad forming - Efficient approach for the manufacturing of complex structured sheet metal blanks for food industry

    Science.gov (United States)

    Spoelstra, Paul; Djakow, Eugen; Homberg, Werner

    2017-10-01

    The production of complex organic shapes in sheet metals is gaining more importance in the food industry due to increasing functional and hygienic demands. Hence it is necessary to produce parts with complex geometries promoting cleanability and general sanitation leading to improvement of food safety. In this context, and especially when stainless steel has to be formed into highly complex geometries while maintaining desired surface properties, it is inevitable that alternative manufacturing processes will need to be used which meet these requirements. Rubber pad forming offers high potential when it comes to shaping complex parts with excellent surface quality, with virtually no tool marks and scratches. Especially in cases where only small series are to be produced, rubber pad forming processes offers both technological and economic advantages. Due to the flexible punch, variation in metal thickness can be used with the same forming tool. The investments to set-up Rubber pad forming is low in comparison to conventional sheet metal forming processes. The process facilitates production of shallow sheet metal parts with complex contours and bends. Different bending sequences in a multiple tool set-up can also be conducted. The planned contribution thus describes a brief overview of the rubber pad technology. It shows the prototype rubber pad forming machine which can be used to perform complex part geometries made from stainless steel (1.4301). Based on an analysis of the already existing systems and new machines for rubber pad forming processes, together with their process properties, influencing variables and areas of application, some relevant parts for the food industry are presented.

  6. Evaluation of the effects of crumb rubber and SBR on rutting resistance of asphalt concrete

    Energy Technology Data Exchange (ETDEWEB)

    Shih, Chuang-Tsair; Tia, Mang; Ruth, B.E. [Univ. of Florida, Gainesville, FL (United States)

    1996-12-31

    This paper presents the results of a study to evaluate the effects of addition of crumb rubber (CR) and styrene-butadiene rubber (SBR) on the rutting resistance of asphalt concrete. These two additives were blended with an AC-20 and an AC-30 grade asphalt cements at different levels of concentrations. These modified and unmodified asphalt blends were tested at intermediate and high temperatures to evaluate their rutting resistance characteristics. They were also used to make Florida type S-I structural surface mixtures. These mixtures were made into Marshall-size specimens by using Gyratory Testing Machine (GTM) equipped with air-roller to compact and density to three compaction levels which simulate three different conditions in the pavement. The FDOT`s (Florida Department of Transportation) Loaded Wheel Tester was also used to evaluate the rutting resistance of these asphalt mixtures. The test results indicate that the modified asphalt mixtures show relatively better rutting resistance and shear resistance as compared with the unmodified asphalt mixtures.

  7. Mechanical Properties of Light Weight Polymer Modified Concrete Made with Chopped Rubber Tires

    Directory of Open Access Journals (Sweden)

    Hassanien Mohammed Thiyab

    2017-07-01

    Full Text Available Lightweight concrete is highly used as loaded and unloaded parts in structures. The low values of compressive strength leads to the production of lightweight concrete blocks that can be used in partitions and the types that have more than 17 MPa and in some structural members that are not highly loaded. This research includes study of mechanical properties of this type of concrete which produced from the waste materials ( chopped rubber tires that are used as a percentage from coarse aggregates by the replacing method. The replacement was as 10%, 20%, 30%, 40% and 50% by weight of coarse aggregates. The mixes were modified by using the styrene butadiene rubber (SBR to increase the values of the mechanical properties and durability. The aim of this investigation is to product special mixes of concrete with a low density and good mechanical properties to reduce the dead load and more economic construction . This study proof the CRT effect on compressive strength whereas it dropped from 62.5 Mpa to 40.8 Mpa by increase percentage of the CRT from 10% to 50%, but in the same time the density lowered up to 33%. The mixes with 10%, 20%, 30% can be regarded as a structural lightweight concrete (exceeded 17 MPa and the other mixes can be used for the production of lightweight blocks used in partitions.

  8. Acoustic Analysis of Composite Soft Materials IV.Evaluation of Compressibility of Bound Rubber in Carbon Black Filled SBR

    Science.gov (United States)

    Maebayashi, Masahiro; Endo, Masashi; Matsuoka, Tatsuro; Koda, Shinobu; Isono, Yoshinobu

    A carbon black (CB) filled styrene-butadiene rubber (SBR) compound was investigated by acoustic techniques, scanning acoustic microscopy and longitudinal wave velocitometry. The CB agglomerates of larger than 5 µm dispersed in the compound mixed by two-roll mill were observed as black spots in acoustic micrographs. On the other hand, the CB agglomerates in the compound mixed by oil-pressure kneader were not observed in the acoustic micrograph, since the particle size of the agglomerates was less than 5 µm. The density and the longitudinal wave velocity of the compound were measured as a function of the weight percentage of the CB. The density and the velocity increased linearly with the content of the CB. The mass ratio of the bound rubber to the CB in the unvulcanized sample was determined by using toluene extraction and thermo gravimetric analysis. The partial specific adiabatic compressibility of the CB was estimated as (-0.5±0.5)×10-10 Pa-1 on the basis of the three states model. The adiabatic compressibility of the bound rubber was (2.2±0.5)×10-10 Pa-1, and it is half of that of the SBR matrix.

  9. Aggregate Production Planning, Casestudy in a Medium-sized Industry of the Rubber Production Line in Ecuador.

    Science.gov (United States)

    Rosero-Mantilla, César; Sánchez-Sailema, Mayra; Sánchez-Rosero, Carlos; Galleguillos-Pozo, Rosa

    2017-06-01

    This research aims to improve the productivity in the rubber line of a medium-sized industry by increasing the production capacities through the use of the Aggregate Production Planning model. For this purpose an analysis of the production processes of the line was made and the aggregate plan was defined evaluating two strategies: Exact Production Plan (Zero Inventory) and Constant Workforce Plan (Vary Inventory) by studying the costs of both inventory maintenance and workforce. It was also determined how the installed capacity was used with the standards of the rubber line and measures for decreasing production costs were proposed. It was proven that only 70% of the plant capacity was being used so it could be possible to produce more units and to obtain a bigger market for the products of this line.+

  10. Constructing covalent interface in rubber/clay nanocomposite by combining structural modification and interlamellar silylation of montmorillonite.

    Science.gov (United States)

    Zha, Chao; Wang, Wencai; Lu, Yonglai; Zhang, Liqun

    2014-11-12

    Strong interfacial interaction and nanodispersion are necessary for polymer nanocomposites with expectations on mechanical performance. In this work, montmorillonite (MMT) was first structurally modified by acid treatment to produce more silanol groups on the layer surface. This was followed by chemical modification of γ-methacryloxy propyl trimethoxysilane molecule (KH570) through covalent grafting with the silanol groups. (29)Si and (27)Al magic angle spinning (MAS) NMR results revealed the microstructural changes of MMT after acid treatment and confirmed the increase of silanol groups on acid-treated MMT surfaces. Thermogravimetric analysis indicated an increase in the grafted amount of organosilane on the MMT surface. X-ray diffraction (XRD) showed that the functionalization process changed the highly ordered stacking structure of the MMT mineral into a highly disordered structure, indicating successful grafting of organosilane to the interlayer surface of the crystalline sheets. The styrene-butadiene rubber (SBR)/MMT nanocomposites were further prepared by co-coagulating with SBR latex and grafted-MMT aqueous suspension. During vulcanization, a covalent interface between modified MMT and rubber was established through peroxide-radical-initiated reactions, and layer aggregation was effectively prevented. The SBR/MMT nanocomposites had highly and uniformly dispersed MMT layers, and the covalent interfacial interaction was finally achieved and exhibited high performance.

  11. Pengaruh Penambahan SBR Bervariasi Pada Perapat Pintu Air

    OpenAIRE

    pramono, Pramono; Musthofa, Hadi

    1994-01-01

    The aim of research is to find out the effect of styrene butadiene rubber used to the tensile strength, compression set, and the Hardness of the seal. The variation of styrene butadiene rubber are 20, 30 and 40 phr; Statistical analysis Paint out that there is signify difference often tensile strength but unsignify difference at the compression set and hardness.

  12. Pengaruh penambahan SBR bervariasi pada perapat pintu air

    Directory of Open Access Journals (Sweden)

    Pramono Pramono

    1994-04-01

    Full Text Available The aim of research is to find out the effect of styrene butadiene rubber used to the tensile strength, compression set, and the Hardness of the seal. The variation of styrene butadiene rubber are 20, 30 and 40 phr; Statistical analysis Paint out that there is signify difference often tensile strength but unsignify difference at the compression set and hardness.

  13. Effect of shearing on the reinforcement properties of vital wheat gluten

    Science.gov (United States)

    The reinforcement properties of vital wheat gluten as a biomaterial filler for a carboxylated styrene-butadiene rubber were examined to assess its effectiveness as a filler for carboxylated styrene-butadiene rubber composites. Composites were formulated using 10-40% vital wheat gluten by mixing aqu...

  14. Prevention of exposure to N-nitrosamines in the rubber industry: new vulcanization accelerators based on 'safe' amines.

    Science.gov (United States)

    Wacker, C D; Spiegelhalder, B; Börzsönyi, M; Brune, G; Preussmann, R

    1987-01-01

    Introduction of 'safe' amino components into traditional accelerator molecules could be an effective measure to prevent formation of carcinogenic N-nitroso compounds during rubber production. About 20 new derivatives of the dithiocarbamate and sulfenamide class, based on 'safe' amines, were synthesized and shown to be suitable for industrial application. Some of the corresponding N-nitrosamines were prepared and investigated for mutagenicity in Salmonella typhimurium TA1535. No or weak mutagenic potential was observed in most cases. The nitrosatability of five sulfenamides derived from 'safe' amines was determined and found to be substantially lower than that of a commercial sulfenamide accelerator tested under identical conditions.

  15. Variation of long periodicity in blends of styrene butadiene, styrene ...

    Indian Academy of Sciences (India)

    1. Instituto de Macromoleculas, Universidade Federal do Rio de Janeiro,. Centro de Tecnologia, Bl. J, Ilha do Fundo, 21945-970, Rio de Jeneiro, RJ, Brazil. 2. Department of Physics, Yuvaraja's College, University of Mysore, Mysore 570 005, India. 3. Department of Studies in Physics, University of Mysore, Manasagangothri,.

  16. Variation of long periodicity in blends of styrene butadiene, styrene ...

    Indian Academy of Sciences (India)

    Instituto de Macromoleculas, Universidade Federal do Rio de Janeiro, Centro de Tecnologia, Bl. J, Ilha do Fundo, 21945-970, Rio de Jeneiro, RJ, Brazil; Department of Physics, Yuvaraja's College, University of Mysore, Mysore 570 005, India; Department of Studies in Physics, University of Mysore, Manasagangothri, ...

  17. Air purification in industrial plants producing automotive rubber components in terms of energy efficiency

    Directory of Open Access Journals (Sweden)

    Grzebielec Andrzej

    2017-04-01

    Full Text Available In automotive industry plants, which use injection molding machines for rubber processing, tar contaminates air to such an extent that air fails to enter standard heat recovery systems. Accumulated tar clogs ventilation heat recovery exchangers in just a few days. In the plant in which the research was conducted, tar contamination causes blockage of ventilation ducts. The effect of this phenomenon was that every half year channels had to be replaced with new ones, since the economic analysis has shown that cleaning them is not cost-efficient. Air temperature inside such plants is often, even in winter, higher than 30°C. The air, without any means of heat recovery, is discharged outside the buildings. The analyzed plant uses three types of media for production: hot water, cold water at 14°C (produced in a water chiller, and compressed air, generated in a unit with a rated power consumption of 180 kW. The aim of the study is to determine the energy efficiency improvement of this type of manufacturing plant. The main problem to solve is to provide an air purification process so that air can be used in heat recovery devices. The next problem to solve is to recover heat at such a temperature level that it would be possible to produce cold for technological purposes without air purification. Experimental studies have shown that air purification is feasible. By using one microjet head, a total of 75% of tar particles was removed from the air; by using 4 heads, a purification efficiency of 93% was obtained. This method of air purification causes air temperature to decrease from 35°C to 20°C, which significantly reduces the potential for heat recovery. The next step of the research was designing a cassette-plate heat exchanger to exchange heat without air purification. The economic analysis of such a solution revealed that replacing the heat exchanger with a new one even once a year was not cost-efficient. Another issue examined in the context of

  18. Air purification in industrial plants producing automotive rubber components in terms of energy efficiency

    Science.gov (United States)

    Grzebielec, Andrzej; Rusowicz, Artur; Szelągowski, Adam

    2017-04-01

    In automotive industry plants, which use injection molding machines for rubber processing, tar contaminates air to such an extent that air fails to enter standard heat recovery systems. Accumulated tar clogs ventilation heat recovery exchangers in just a few days. In the plant in which the research was conducted, tar contamination causes blockage of ventilation ducts. The effect of this phenomenon was that every half year channels had to be replaced with new ones, since the economic analysis has shown that cleaning them is not cost-efficient. Air temperature inside such plants is often, even in winter, higher than 30°C. The air, without any means of heat recovery, is discharged outside the buildings. The analyzed plant uses three types of media for production: hot water, cold water at 14°C (produced in a water chiller), and compressed air, generated in a unit with a rated power consumption of 180 kW. The aim of the study is to determine the energy efficiency improvement of this type of manufacturing plant. The main problem to solve is to provide an air purification process so that air can be used in heat recovery devices. The next problem to solve is to recover heat at such a temperature level that it would be possible to produce cold for technological purposes without air purification. Experimental studies have shown that air purification is feasible. By using one microjet head, a total of 75% of tar particles was removed from the air; by using 4 heads, a purification efficiency of 93% was obtained. This method of air purification causes air temperature to decrease from 35°C to 20°C, which significantly reduces the potential for heat recovery. The next step of the research was designing a cassette-plate heat exchanger to exchange heat without air purification. The economic analysis of such a solution revealed that replacing the heat exchanger with a new one even once a year was not cost-efficient. Another issue examined in the context of energy efficiency was

  19. Cancer incidence in cohorts of workers in the rubber manufacturing industry first employed since 1975 in the UK and Sweden.

    Science.gov (United States)

    Boniol, M; Koechlin, A; Sorahan, T; Jakobsson, K; Boyle, P

    2017-06-01

    Increased cancer risks have been reported among workers in the rubber manufacturing industry employed before the 1960s, but it is unclear for workers hired subsequently. The present study focused on cancer incidence among rubber workers first employed after 1975 in Sweden and the UK. Two cohorts of rubber workers employed for at least 1 year were analysed. Standardised incidence ratios (SIRs), based on country-specific and period-specific incidence rates, were analysed for all cancers combined (except non-melanoma skin), bladder, lung, stomach cancer, leukaemia, non-Hodgkin's lymphoma and multiple myeloma. Exploratory analyses were conducted for other cancers with a minimum of 10 cases in both genders combined. 16 026 individuals (12 441 men; 3585 women) contributed to 397 975 person-years of observation, with 846 cancers observed overall (437 in the UK, 409 in Sweden). No statistically significant increased risk was observed for any site of cancer. A reduced risk was evident for all cancers combined (SIR=0.83, 95% CI (0.74 to 0.92)), lung cancer (SIR=0.74, 95% CI (0.59 to 0.93)), non-Hodgkin's lymphoma (SIR=0.67, 95% CI (0.45 to 1.00)) and prostate cancer (SIR=0.77, 95% CI (0.64 to 0.92)). For stomach cancer and multiple myeloma, SIRs were 0.93 (95% CI (0.61 to 1.43)) and 0.92 (95% CI 0.44 to 1.91), respectively. No increased risk of bladder cancer was observed (SIR=0.88, 95% CI (0.61 to 1.28)). No significantly increased risk of cancer incidence was observed in the combined cohort of rubber workers first employed since 1975. Continued surveillance of the present cohorts is required to confirm absence of long-term risk and confirmatory findings from other cohorts would be important. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  20. Influence of glutathione-related genes on symptoms and immunologic markers among vulcanization workers in the southern Sweden rubber industries.

    Science.gov (United States)

    Jönsson, Lena S; Jönsson, Bo A G; Axmon, Anna; Littorin, Margareta; Broberg, Karin

    2008-07-01

    The aim was to elucidate the role of genetic variants on symptoms of the eyes and airways, headache and nausea, as well as on immunologic markers, among vulcanization workers in the contemporary Swedish rubber industry. Polymorphisms in genes, which are involved in the defense against reactive oxygen species and metabolism of toxic substances present in the vulcanization fumes, were analyzed. One hundred and forty-five exposed and 117 unexposed workers were included in the study. Medical and occupational histories were obtained in structured interviews. Symptoms were recorded and immunologic markers analyzed in blood. Polymorphisms in glutathione-related genes (glutamate cysteine ligase catalytic subunit (GCLC)-129, glutamate cysteine ligase modifier subunit (GCLM)-588, glutathione S-transferase alpha 1 (GSTA1)-52, GSTM1*O, GSTP1-105, GSTP1-114, and GSTT1*O) were analyzed by Taqman-based allelic discrimination and ordinary PCR. A protective effect of GSTA1-52 (G/A + A/A) genotype on symptoms and immunologic cells, in particular among exposed workers, was suggested. Exposed workers with GSTT1*O had increased risk of nosebleed compared to exposed workers with GSTT1*1. Exposed workers with GSTP1-105 (ile/val + val/val) had decreased levels of total immunoglobulin E (IgE) compared to exposed workers with GSTP1-105 ile/ile. GCLC-129 variant genotype demonstrated increased levels of immunologic cells among exposed workers, although statistical significance was not reached. Our data indicate that hereditary factors influence the susceptibility to symptoms and the immunologic response of workers in the rubber industry.

  1. Thermolysis of scrap tire and rubber in sub/super-critical water.

    Science.gov (United States)

    Li, Qinghai; Li, Fuxin; Meng, Aihong; Tan, Zhongchao; Zhang, Yanguo

    2017-10-25

    The rapid growth of waste tires has become a serious environmental issue. Energy and material recovery is regarded as a promising use for waste tires. Thermolysis of scrap tire (ST), natural rubber (NR), and styrene-butadiene rubber (SBR) was carried out in subcritical and supercritical water using a temperature-pressure independent adjustable batch tubular reactor. As a result, oil yields increased as temperature and pressure increased, and they reached maximum values as the state of water was near the critical point. However, further increases in water temperature and pressure reduced the oil yields. The maximum oil yield of 21.21% was obtained at 420 °C and 18 MPa with a reaction time of 40 min. The relative molecular weights of the chemicals in the oil products were in the range of 70-140 g/mole. The oil produced from ST, NR, and SBR contained similar chemical compounds, but the oil yield of SR was between those of NR and SBR. The oil yield from thermolysis of subcritical or supercritical water should be further improved. The main gaseous products, including CH4, C2H2, C2H4, C2H6, and C3H8, increased with reaction time, temperature, and pressure, whereas the solid residues, including carbon black and impurities, decreased. These results provide useful information to develop a sub/super-critical water thermolysis process for energy and material regeneration from waste tires. Copyright © 2017 Elsevier Ltd. All rights reserved.

  2. 40 CFR 63.190 - Applicability and designation of source.

    Science.gov (United States)

    2010-07-01

    ...-styrene resins (MBS) (iii) Butadiene-furfural cotrimer, (iv) Methylmethacrylate-acrylonitrile-butadiene.... (1) Styrene-butadiene rubber production (butadiene and styrene emissions only). (2) Polybutadiene rubber production (butadiene emissions only). (3) The processes producing the agricultural chemicals...

  3. VARIMAX MODEL TO FORECAST THE EMISSION OF CARBON DIOXIDE FROM ENERGY CONSUMPTION IN RUBBER AND PETROLEUM INDUSTRIES SECTORS IN THAILAND

    Directory of Open Access Journals (Sweden)

    Pruethsan Sutthichaimethee

    2017-05-01

    Full Text Available This study aims to analyze the forecasting of CO2 emission from the energy consumption in the Rubber, Chemical and Petroleum Industries sectors in Thailand. The scope of research employed the input-output table of Thailand from the year 2000 to 2015. It was used to create the model of CO2 emission, population, GDP growth and predict ten years and thirty years in advance. The model used was the VARIMAX Model which was divided into two models. The results show that from the first model by using which predicted the duration of ten years (2016-2025 by using VARIMAX Model (2,1,2, On average, Thailand has 17.65% higher quantity of CO2 emission than the energy consumption sector (in 2025. The second model predicted the duration of 30 years (2016-2045 by using VARIMAX Model (2,1,3 shows that Thailand has average 39.68% higher quantity of CO2 emission than the energy consumption sector (in 2025. From the analyses, it shows that Thailand has continuously higher quantity of CO2 emission from the energy consumption. This negatively affects the environmental system and economical system of the country incessantly. This effect can lead to unsustainable development.

  4. Levels of 2-thiothiazolidine-4-carboxylic acid (TTCA) and effect modification of polymorphisms of glutathione-related genes in vulcanization workers in the southern Sweden rubber industries.

    Science.gov (United States)

    Jönsson, Lena S; Broberg, Karin; Bergendorf, Ulf; Axmon, Anna; Littorin, Margareta; Jönsson, Bo A G

    2007-07-01

    Workers in the rubber industry are exposed to a complex mixture of hazardous substances and have increased risk of developing several diseases. However, there is no up to date survey examining the exposure in the Swedish rubber industry. One of the toxic compounds in the industry is carbon disulfide (CS(2)), which is biotransformed to 2-thiothiazolidine-4-carboxylic acid (TTCA). TTCA is used as a biomarker of CS(2) exposure, but there seem to exist inter- and intraindividual variability; which could partly be due to genetic variation. The aim of the study was to determine TTCA levels and the modifying effects of glutathione-related genes in a group of Swedish rubber workers. Urine was collected from both exposed workers and controls during the last 4 h of the work shift. The level of TTCA in urine was analyzed by liquid chromatograpy tandem mass spectrometry. Genotyping of the single nucleotide polymorphisms GCLC-129, GCLM-588, GSTA1-52, GSTP1-105 and GSTP1-114 and deletions of GSTM1 and GSTT1 were performed with real-time PCR or ordinary PCR and subsequent agarose electrophoresis. The highest levels of TTCA were found among workers curing with salt bath, hot air, microwaves or fluid-bed, and lower levels were found among workers curing with injection and compression molding. Furthermore, with respect to GSTM1 and GSTT1 there were statistically significant differences in TTCA-levels between genotypes among exposed workers but not among controls. The other five polymorphisms had no impact on the TTCA levels. The present study demonstrates relatively high levels of TTCA in urine from Swedish rubber workers. Polymorphisms in GSTM1 and GSTT1 modify the levels.

  5. New industrial heat pump applications to a synthetic rubber plant. Final report, Phase IIA

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-12-31

    This report summarizes the results of the Phase IIA of the DOE sponsored study titled, Advanced Industrial Heat Pump Application and Evaluation. The scope of this phase of the study was to finalize the process design of the heat pump scheme, develop a process and instrumentation diagram, and a detailed cost estimate for the project. This information is essential for the site management to evaluate the economic viability and operability of the proposed heat pump design, prior to the next phase of installation and testing.

  6. Perbandingan Sifat Mekanik Fisik Vulkanisat Sbr Dan Sbr/nr Menggunakan Bahan Pengisi Pati Termodifikasi Resorcinol Formaldehyde

    OpenAIRE

    Susanto, Tri

    2016-01-01

    Penelitian ini bertujuan untuk mengetahui perbandingan karakteristik vulkanisat komposit Styrene Butadiene Rubber (SBR) dan campuran Styrene Butadiene Rubber dan Natural Rubber (SBR/NR) yang keduanya menggunakan bahan pengisi starch (pati) termodifikasi Resorcinol Formaldehyde (SRF) sebagai bahan substituen Carbon Black (CB). Rasio CB/SRF untuk tiap vulkanisat yang digunakan berturut-turut 60/0; 55/5; 50/10; 45/15; 40/20 phr. Pengamatan dilakukan dengan menguji sifat physco-mechanic vulkanisa...

  7. SILICONE RUBBER MOULDS FOR FOOTWEAR

    Directory of Open Access Journals (Sweden)

    Cornelia LUCA

    2013-05-01

    Full Text Available The leather confections industry uses the silicone rubber moulds for the symbols,notices and models stamping on the footwear or morocco goods parts. The paper presents somecontributions in this kind of devices manufacturing technology

  8. Leachable diphenylguanidine from rubber closures used in pre-filled syringes: A case study to understand solid and solution interactions with oxytocin.

    Science.gov (United States)

    Zidan, Ahmed S; Aqueel, Sabir M; Alayoubi, Alaadin; Mohammad, Adil; Zhang, Jinhui; Rahman, Ziyaur; Faustino, Patrick; Lostritto, Richard T; Ashraf, Muhammad

    2017-10-30

    Leachables derived from multi-component drug-device syringe systems can result in changes to the quality of drug products. Diphenylguanidine (DPG), a leachable released from styrene butadiene rubber syringe plungers, interacts with Oxytocin to form protein-adducts. This study investigated the mechanism and kinetics of this interaction in both solid and solution states through in-vitro tests and spectroscopic methods For solid state interaction, the protein-adducts with DPG were characterized using SEM, XRD, DSC, FTIR, 13 C ss NMR, and dissolution analysis. For solution state interaction, LC-HRMS was used to assess stability of Oxytocin solutions in presence of various concentrations of DPG at 25°C and 40°C for 4 weeks. Moreover, molecular docking analysis was used to identify possible molecular configurations of the interaction.Results were consistent with the formation of a new solid state with distorted surface morphology for oxytocin-DPG adducts, in which the oxytocin carbonyl group(s) and the secondary amine groups of DPG interact. This interaction was also confirmed by molecular docking analysis through hydrogen bonding (2.31Å) and Van der Waal attraction (3.14Å). Moreover, LC-HRMS analysis revealed an increase in Oxytocin stability and suppression of Oxytocin dimerization by DPG. A potential reduction in the rate of Oxytocin dissolution from the formed adducts was indicative of its strong association with DPG. Hence, the leaching potential of DPG from rubber closures and plungers should be monitored and controlled to maintain the quality and stability of the pharmaceutical product. Published by Elsevier B.V.

  9. Allergic reactions to natural rubber.

    Science.gov (United States)

    Slater, J E

    1992-03-01

    Immediate hypersensitivity reactions to natural rubber pose a significant risk to patients with spina bifida and urogenital abnormalities, health care workers, and rubber industry workers. Other patients, outside of these high risk groups, have experienced severe allergic reactions to natural rubber as well. Awareness of this life-threatening condition by health care providers is essential if reactions are to be prevented. History alone is inadequate to identify all patients at risk, and reliable testing materials are not yet approved or widely available. Nonrubber medical devices are readily available for most uses; however, the only rubber-free condoms currently on the market do not prevent the transmission of sexually transmitted disease. The identification and detection of rubber antigens, along with mandated labeling for rubber antigen content, will contribute to the care of this growing population of patients. Efforts by the rubber industry to decrease the antigen content of natural rubber products will decrease the risk of reaction among sensitized patients and will, very likely, decrease the rate of sensitization in the future.

  10. Materials for the General Aviation Industry: Effect of Environment on Mechanical Properties of Glass Fabric/Rubber Toughened Vinyl Ester Laminates

    Science.gov (United States)

    McBride, Timothy M.

    1995-01-01

    A screening evaluation is being conducted to determine the performance of several glass fabric/vinyl ester composite material systems for use in primary General Aviation aircraft structures. In efforts to revitalize the General Aviation industry, the Integrated Design and Manufacturing Work Package for General Aviation Airframe and Propeller Structures is seeking to develop novel composite materials and low-cost manufacturing methods for lighter, safer and more affordable small aircraft. In support of this Work Package, this study is generating material properties for several glass fabric/rubber toughened vinyl ester composite systems and investigates the effect of environment on property retention. All laminates are made using the Seemann Composites Resin Infusion Molding Process (SCRIMP), a potential manufacturing method for the General Aviation industry.

  11. Hydrogenated nitrile rubber for improved durability of automotive rubber parts

    Energy Technology Data Exchange (ETDEWEB)

    Mirza, J.; Leibbrandt, F.; Thoermer, J.

    1987-01-01

    Rubber articles with improved heat resistance and better performance characteristics are becoming of increasing importance for the automotive industry. A new type of elastomer has therefore been developed based on saturated hydrocarbon backbone - for improved heat resistance - with nitrile side groups providing good resistance to swelling. Some of the typical characteristics of hydrogenated nitrile rubber (HNBR) vulcanizates such as good physical properties pattern at elevated low temperatures dynamic properties, ozone resistance and swelling in automotive fluids are discussed. Potential applications are suggested to improve the performance of various rubber parts used in automotive applications such as high performance seals.

  12. [To-day exposure to occupational carcinogens and their effects. The experience of the rubber industry, iron metallurgy, asphalt work and aviculture].

    Science.gov (United States)

    Barbieri, Pietro Gino

    2009-01-01

    While the progressive improvement of hygiene situations in the workplaces has taken to a reduction of chemical carcinogens exposure, in recent years in Italy the number of compensated occupational cancer resulting from carcinogens exposures of distant decades, has been increasing. Nevertheless, several experiences suggest that the proportion of occupational cancers unrecognised and not notified, as required by law, still remains important. This contribution concerns some experiences, performed between 2004-2008 by the Local Occupational Health Service (SPSAL) located in a highly industrialised province, on the working sector of rubber, iron and steel industry, the asphalt working and the poultry stock-breeders. This work concerns the following issues: - the evaluation of carcinogens exposure; - technical preventive measures and personal protection; - the level of workers' information and formation and the registration of exposed workers; - the characterization of work-related cancer. The results of the 5 years of activity allow us to underline that, in the most of 49 plants involved in the study, the carcinogens exposure evaluation and the prevention and protection measures were lacking. Information of workers was largely deficient and the registration of exposed workers was absent. A major attention to detect and to evaluate the work-related cancer has allowed us to recognize 50 new cases in the iron-steel industries and 21 new cases in a rubber industry. Although this experience concerns only few occupational fields, it provides the basis to call for a greater commitment of SPSAL addressed to companies and general practitioners to both, the promotion and surveillance of the correct procedures of carcinogens exposure evaluation and his prevention, and the active detection of occupational cancer, still missing.

  13. Regulamentação pública e conduta das firmas no sistema agroindustrial da borracha natural entre 1997 e 2000 Regulation and behavior of firms in Brazil's natural rubber agro-industrial system between 1997-2000

    Directory of Open Access Journals (Sweden)

    Augusto Hauber Gamero

    2002-01-01

    Full Text Available A necessidade de regulamentação no sistema agroindustrial (SAG da borracha natural no Brasil é evidente. Desde a metade do século, quando o país passou a importar esse produto, vários esforços governamentais vêm sendo definidos, objetivando o desenvolvimento sustentável do setor da produção agrícola nacional de borracha. No ano de 1997, criou-se uma política de subvenção direta à produção. Dada a estrutura desse SAG, associada à conjuntura do mercado internacional e a uma regulamentação falha do governo federal, começaram a surgir indícios de abuso de poder de mercado pela indústria pneumática instalada no país, principal consumidora do produto. Utilizando o arcabouço teórico da organização industrial, neste artigo se procurou levantar evidências nesse sentido.The need for regulation of Brazil’s natural rubber agro-industrial system (SAG is evident. Since the middle of the 20th century, when the country began importing rubber, many governmental efforts have been made to promote the sustainable development of Brazil’s natural rubber productive sector. In 1997, the Brazilian government created a direct subvention policy to assist rubber producers. Given the structure of Brazil’s SAG, the international rubber market, and imperfect regulation by the Federal Government, it would not be unexpected to find signs that Brazil’s largest natural rubber consumer, the domestic tire industry, has begun to abusively exercise its market power. Using the theoretical structure of Industrial Organization, this paper tries to show evidences of this abuse.

  14. Statistical Analysis of Reducing Biochemical Oxygen Demand (BOD) on Industrial Rubber Wastewater using Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Syakur, Abdul; Zaman, Badrus; Yunita Nurmaliakasih, Dias

    2017-04-01

    Dielectric Barrier Discharge plasma (DBD) is one of type non-thermal plasma (non-equilibrium plasma) or can be referred to as cold plasma. In this research, DBD plasma be utilized to reduce organic compounds like Biochemichal oxygen demand in the wastewater rubber processing. In the environment field DBD plasma has been used as a treatment for reducing air pollutants such as gas COx, NOx and HC. In addition DBD plasma have been developed to processed wastewater as an alternative technology in wastewater treatment. DBD plasma appears when the electrode is given a high voltage so that, it will form electric field in the area of the electrodes which allows the ionization and the presence of high-energy electrons in the area. The presence of these electrons will ionize molecules of H2O into active species such as OH•, H• and H2O2. The active species that can oxidize into CO2 and H2O so, BOD that can be degraded. In this research for wastewater treatment used high voltage are 10kV, 11kV, 12kV and 13kV and variations of processing time for 5, 10, 15, 20, and 25 (minutes). By increasing the voltage and extend the contact time then the speed variation of electrons to ionize the greater and more active species to be formed to degrade the pollutants to the maximum. This research used quantitative analysis with statistical analysis using SPSS software.

  15. Rubber compounding and processing

    CSIR Research Space (South Africa)

    John, MJ

    2014-06-01

    Full Text Available This chapter presents an overview on the compounding and processing techniques of natural rubber compounds. The introductory portion deals with different types of rubbers and principles of rubber compounding. The primary and secondary fillers used...

  16. Pengaruh Temperatur Vulkanisasi Terhadap Kekuatan Tarik (Tensile Strength) Pada Packing Pintu Rebusan PT. Industri Karet Nusantara Medan

    OpenAIRE

    Ayutami, Rizki

    2012-01-01

    In this paper will discuss how is the influence of temperature vulcanization which in used at Rubber Articles Factory in PT. Rubbin Industry Nusantara Medan. The start with selection raw materials natural rubber and synthetic rubber in used until became rubber articles. The variety rubber which in used to produce rubber articles is rubber smoke sheet, there for variety synthetic rubber which used is SBR (Styrine Butadine Rubber). At the first process, main material rubber and chemical is mixe...

  17. Reinforcement effect of soy protein/carbohydrate ratio in styrene-butadiene polymer

    Science.gov (United States)

    Soy protein and carbohydrate at different ratios were blended with latex to form composites. The variation of protein to carbohydrate ratio has a sifnificant effect on the composite properties and the results from dynamic mechanical method showed a substantial reinforcement effect. The composites ...

  18. Reinforcement Effect of Alkali Hydrolyzed Wheat Gluten and Starch in Carboxylated Styrene-Butadiene Composites

    Science.gov (United States)

    Wheat gluten (WG) and wheat starch (WS) are the protein and carbohydrate obtained from wheat flours. Wheat gluten is not water soluble or dispersible due to its hydrophobic nature. To prepare wheat gluten dispersions, an alkali hydrolysis reaction was carried out to produce a stable aqueous disper...

  19. Polymer composites prepared from heat-treated starch and styrene-butadiene latex

    Science.gov (United States)

    Thermoplastic starch/latex polymer composites were prepared using styrene–butadiene (SB) latex and heat-treated cornstarch. The composites were prepared in a compression mold at 130 °C, with starch content 20%. An amylose-free cornstarch, waxy maize, was used for this research and the heat treatment...

  20. Chemical Contaminant and Decontaminant Test Methodology Source Document. Second Edition

    Science.gov (United States)

    2012-07-01

    rubberstyrene butadiene rubber ( SBR ); 60A hardness; black color, fabric-reinforced SBR rubber , 1/8 in. thick. Navy Ship Topcoat- Painted Carbon... APPLICATIONS INTERNATIONAL CORPORATION Gunpowder, MD 21010-0068 July 2012 Approved for public release; distribution is unlimited... APPLICATIONS INTERNATIONAL CORPORATION Gunpowder, MD 21010-0068 REPORT DOCUMENTATION PAGE Form Approved OMB No. 0704-0188 Public reporting

  1. The rubber tree genome reveals new insights into rubber production and species adaptation.

    Science.gov (United States)

    Tang, Chaorong; Yang, Meng; Fang, Yongjun; Luo, Yingfeng; Gao, Shenghan; Xiao, Xiaohu; An, Zewei; Zhou, Binhui; Zhang, Bing; Tan, Xinyu; Yeang, Hoong-Yeet; Qin, Yunxia; Yang, Jianghua; Lin, Qiang; Mei, Hailiang; Montoro, Pascal; Long, Xiangyu; Qi, Jiyan; Hua, Yuwei; He, Zilong; Sun, Min; Li, Wenjie; Zeng, Xia; Cheng, Han; Liu, Ying; Yang, Jin; Tian, Weimin; Zhuang, Nansheng; Zeng, Rizhong; Li, Dejun; He, Peng; Li, Zhe; Zou, Zhi; Li, Shuangli; Li, Chenji; Wang, Jixiang; Wei, Dong; Lai, Chao-Qiang; Luo, Wei; Yu, Jun; Hu, Songnian; Huang, Huasun

    2016-05-23

    The Para rubber tree (Hevea brasiliensis) is an economically important tropical tree species that produces natural rubber, an essential industrial raw material. Here we present a high-quality genome assembly of this species (1.37 Gb, scaffold N50 = 1.28 Mb) that covers 93.8% of the genome (1.47 Gb) and harbours 43,792 predicted protein-coding genes. A striking expansion of the REF/SRPP (rubber elongation factor/small rubber particle protein) gene family and its divergence into several laticifer-specific isoforms seem crucial for rubber biosynthesis. The REF/SRPP family has isoforms with sizes similar to or larger than SRPP1 (204 amino acids) in 17 other plants examined, but no isoforms with similar sizes to REF1 (138 amino acids), the predominant molecular variant. A pivotal point in Hevea evolution was the emergence of REF1, which is located on the surface of large rubber particles that account for 93% of rubber in the latex (despite constituting only 6% of total rubber particles, large and small). The stringent control of ethylene synthesis under active ethylene signalling and response in laticifers resolves a longstanding mystery of ethylene stimulation in rubber production. Our study, which includes the re-sequencing of five other Hevea cultivars and extensive RNA-seq data, provides a valuable resource for functional genomics and tools for breeding elite Hevea cultivars.

  2. Anomalous glass transition behavior of SBR-Al2O3 nanocomposites at small filler concentrations

    Science.gov (United States)

    Sushko, Rymma; Filimon, Marlena; Dannert, Rick; Elens, Patrick; Sanctuary, Roland; Baller, Jörg

    2014-10-01

    Elastomers filled with hard nanoparticles are of great technical importance for the rubber industry. In general, fillers improve mechanical properties of polymer materials, e.g. elastic moduli, tensile strength etc. The smaller the size of the particles, the larger is the interface where interactions between polymer molecules and fillers can generate new properties. Using temperature-modulated differential scanning calorimetry and dynamic mechanical analysis, we investigated the properties of pure styrene-butadiene rubber (SBR) and SBR/alumina nanoparticles. Beside a reinforcement effect seen in the complex elastic moduli, small amounts of nanoparticles of about 2 wt% interestingly lead to an acceleration of the relaxation modes responsible for the thermal glass transition. This leads to a minimum in the glass transition temperature as a function of nanoparticle content in the vicinity of this critical concentration. The frequency dependent elastic moduli are used to discuss the possible reduction of the entanglement of rubber molecules as one cause for this unexpected behavior.

  3. Anomalous glass transition behavior of SBR-Al₂O₃ nanocomposites at small filler concentrations.

    Science.gov (United States)

    Sushko, Rymma; Filimon, Marlena; Dannert, Rick; Elens, Patrick; Sanctuary, Roland; Baller, Jörg

    2014-10-24

    Elastomers filled with hard nanoparticles are of great technical importance for the rubber industry. In general, fillers improve mechanical properties of polymer materials, e.g. elastic moduli, tensile strength etc. The smaller the size of the particles, the larger is the interface where interactions between polymer molecules and fillers can generate new properties. Using temperature-modulated differential scanning calorimetry and dynamic mechanical analysis, we investigated the properties of pure styrene-butadiene rubber (SBR) and SBR/alumina nanoparticles. Beside a reinforcement effect seen in the complex elastic moduli, small amounts of nanoparticles of about 2 wt% interestingly lead to an acceleration of the relaxation modes responsible for the thermal glass transition. This leads to a minimum in the glass transition temperature as a function of nanoparticle content in the vicinity of this critical concentration. The frequency dependent elastic moduli are used to discuss the possible reduction of the entanglement of rubber molecules as one cause for this unexpected behavior.

  4. Cryogenic Deflashing for Rubber Products

    Directory of Open Access Journals (Sweden)

    Abhilash M.

    2018-01-01

    Full Text Available Deflashing is the process of removal of excess flashes from the rubber products. Initially deflashing was a manual operation where dozen of workers, seated at small work stations would take each part and trim the excess rubber off with scissors, knives or by grinding. Still the same method is employed in most of the rubber industry. The drawbacks of this method are demand inconsistent and repeatable quality. Work done by hand is often inconsistent. There are commercially available cryogenic deflashing machine but they are too expensive hence cost effectiveness is also a prime factor. The objective of this paper is to develop a technique, to identify the media through which the flashes can be removed easily and effectively. Based on the test results obtained from testing of five different types of media, ABCUT Steel media gave best results. The testing of the ABCUT Steel media on rubber samples like O-rings, grommet tail door, bottom bush etc. shows good results.

  5. History of Rubber and Its Use

    Science.gov (United States)

    Müller, Ingo; Strehlow, Peter

    Despite its spectacular properties rubber was not much good for anything before the latter part of the 19th century. To be sure the Aztecs had used it to make balls for their ceremonial ball games - or so we are told. But those games died along with the Aztec culture in the 16th century and there is no record of other useful applications until the late 18th century. But then, after that, rubber took off in a small way. After the American inventor Samuel Peal had obtained a patent in 1791 for the production of rubber-coated watertight textiles, the Scottish chemist Charles Macintosh (1766-1843) used such textiles for making rain-coats, and Thomas Hancock (1786-1865) produced rubber boots. At that time it was not really appropriate to speak of a rubber industry. What little material the evil-smelling workshops in New York and London needed, could be satisfied with the import of 30 tons of Caoutchouc1 annually - extracted from the sap of the tree Hevea brasiliensis - and most of that went for making erasers. Indeed, it had been reported by the English minister and scientist Joseph Priestley (1733-1804) that pieces of rubber are well-suited to rub out (sic!) pencil marks. Even today there is nothing better for the purpose and rubber became the English word for Caoutchouc.

  6. Cream concentrated latex for foam rubber products

    Science.gov (United States)

    Suksup, R.; Imkaew, C.; Smitthipong, W.

    2017-12-01

    Fresh natural latex (around 40% rubber and 60% water) can be transformed to concentrated natural latex (around 60% rubber and 40% water) in order to realise economical transportation and easier latex product’s preparation. The concentrated natural latex is an extremely valuable material. It can be applied for many types of products, for example, foam rubber as pillow and mattress, elastic band, etc. Industrially, the concentrated natural latex can be prepared by centrifugation which requires an enormous expensive machine. From the eco-friendly products point of view, most of rubber entrepreneurs in the world try to develop a green rubber product. So, the main objective of this study is to prepare the cream concentrated latex without any sophisticated machine. Thus, we work on a simple, cheap and green method that does not use any expensive machine but uses water-based chemical as sodium alginate to prepare the cream concentrated latex. The optimal amount of sodium alginate in the latex was studied. The main characteristics of the cream concentrated latex were tested by various technics, such as alkalinity, total solid content (TSC), dry rubber content (DRC), etc. We found that there are no significant differences of results between fresh natural latex and cream concentrated latex, except for the TSC and DRC. The TSC and DRC of cream latex are higher than those of fresh natural latex. Finally, we propose a model of natural rubber particle and sodium alginate to form the cream concentrated latex.

  7. Flashover Characteristics of Silicone Rubber Sheets under Various Environmental Conditions

    OpenAIRE

    Arshad; Azam Nekahi; Scott G. McMeekin; Masoud Farzaneh

    2016-01-01

    Silicone rubber insulators are replacing the conventional ceramic and porcelain insulators rapidly in power transmission and distribution industry. Very limited field knowledge is available about the performance of silicone rubber insulators in polluted and contaminated environments and therefore need further investigation. A comprehensive analysis of silicone rubber sheets (intended for coating outdoor insulators) was carried out in this paper based on experimental results. The main performa...

  8. Developments in rubber technology 2 synthetic rubbers

    CERN Document Server

    Lee, K

    1981-01-01

    This book is intended for those people who have a knowledge or understanding of rubber materials and processes but who wish to update their knowledge. It should be read in conjunction with Developments in Rubber Technology-l as that volume discussed developments in natural rubber and selected special purpose synthetic rubbers as well as additives. The authors have been selected for their expertise in each particular field and we, as editors, would like to express our appreciation to the individual authors and also to their companies. Such a book would be impossible to produce without such active cooperation as we have received. Volumes 1 and 2 of Developments in Rubber Technology cover rubbers which are processed and vulcanised in the traditional manner. It is appreciated that the omission of non-vulcanised rubber materials (the so­ called thermoplastic elastomers) will be unwelcome to many readers but it is intended, because of the size of the subject, to cover these materials in a subsequent volume. A.W. K...

  9. Silencing the lettuce homologs of small rubber particle protein does not influence natural rubber biosynthesis in lettuce (Lactuca sativa).

    Science.gov (United States)

    Chakrabarty, Romit; Qu, Yang; Ro, Dae-Kyun

    2015-05-01

    Natural rubber, cis-1,4-polyisoprene, is an important raw material in chemical industries, but its biosynthetic mechanism remains elusive. Natural rubber is known to be synthesized in rubber particles suspended in laticifer cells in the Brazilian rubber tree (Hevea brasiliensis). In the rubber tree, rubber elongation factor (REF) and its homolog, small rubber particle protein (SRPP), were found to be the most abundant proteins in rubber particles, and they have been implicated in natural rubber biosynthesis. As lettuce (Lactuca sativa) can synthesize natural rubber, we utilized this annual, transformable plant to examine in planta roles of the lettuce REF/SRPP homologs by RNA interference. Among eight lettuce REF/SRPP homologs identified, transcripts of two genes (LsSRPP4 and LsSRPP8) accounted for more than 90% of total transcripts of REF/SRPP homologs in lettuce latex. LsSRPP4 displays a typical primary protein sequence as other REF/SRPP, while LsSRPP8 is twice as long as LsSRPP4. These two major LsSRPP transcripts were individually and simultaneously silenced by RNA interference, and relative abundance, polymer molecular weight, and polydispersity of natural rubber were analyzed from the LsSRPP4- and LsSRPP8-silenced transgenic lettuce. Despite previous data suggesting the implications of REF/SRPP in natural rubber biosynthesis, qualitative and quantitative alterations of natural rubber could not be observed in transgenic lettuce lines. It is concluded that lettuce REF/SRPP homologs are not critically important proteins in natural rubber biosynthesis in lettuce. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Pathway for high-quality reclaim by thermal treatment of sulfur-vulcanized SBR

    NARCIS (Netherlands)

    Saiwari, Sitisaiyidah; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2011-01-01

    De-vulcanization of SBR (Styrene Butadiene Rubber) is a challenge, as the broken polymer chains tend to re-arrange. This influences the properties of the reclaimed and re-vulcanized rubber, and reduces the quality of the recycled material. Within this study, the breakdown of sulfur-cured SBR in a

  11. Chrome-tanned leather shavings as a filler of butadiene-acrylonitrile rubber.

    Science.gov (United States)

    Przepiórkowska, A; Chrońska, K; Zaborski, M

    2007-03-06

    The noxious wastes from the tanning industry such as chrome-tanned leather shavings were used as the only filler of rubber mixes containing carboxylated butadiene-acrylonitrile rubber (XNBR) or butadiene-acrylonitrile rubber (NBR), and a dispersing agent Limanol PEV (Schill & Seilacher). The best form addition of leather powder to the rubber mixes is mixed the waste protein with zinc oxide. The leather powder added to the rubber mixes improves the mechanical properties: tensile strength (T(s)), elongation at break (epsilon(b)) and increase the cross-linking density of carboxylated XNBR and NBR rubber mixes. Satisfactory results of these studies are presented in this work.

  12. A study of amino acid modifiers in guayule natural rubber

    Science.gov (United States)

    Natural rubber from the Hevea tree is a critical agricultural material vital to United States industry, medicine, and defense, yet the country is dependent on imports to meet domestic needs. Guayule, a desert shrub indigenous to the US, is under development as an alternative source of natural rubber...

  13. REVIEW or POST- HARVEST DETERIORATION or RUBBER SEEDS ~

    African Journals Online (AJOL)

    Journal or Agriculture in Social Research (JASR) v01. 7, No.2, 2007 a '. REVIEW or POST- HARVEST DETERIORATION or RUBBER SEEDS ~. CLARA LEYIBO IGELEKE. AND vrcronmooun omorwsr. ABSTRACT , r r ~ ' Rubber seeds have potential use as a source of industrial oil as well as a protein supplement for use in ...

  14. Investigating the tension load of rubber composites by impact ...

    Indian Academy of Sciences (India)

    capacity conveyors or those working under heavy conditions. (sharp slope and high speed, with big lengths to transport), which need a very good breaking strength, special flexibility and high reliability [9]. Rubber industry often faces the prob- lem of wear of rubber parts. The wear of CBs is character- ized by abrasion [10].

  15. Characterization of some selected vulcanized and raw silicon rubber materials

    Science.gov (United States)

    Sasikala, A.; Kala, A.

    2017-06-01

    Silicone Rubber is a high need of importance of Medical devices, Implants, Aviation and Aerospace wiring applications. Silicone rubbers are widely used in industry, and there are in multiple formulations. A raw and vulcanized silicone rubber Chemical and Physical structures of particles was confirmed and mechanical strength has been analyzed by FTIR spectroscopy. Thermal properties studied from Thermo Gravimetric Analysis (TGA) and Differential Scanning Calorimetry (DSC) analysis. Activation energy of the rubber materials were calculated using Broido method, Piloyon-Novikova relation and coats-Red fern methods.

  16. Filler Network Model of Filled Rubber Materials to Estimate System Size Dependence of Two-Dimensional Small-Angle Scattering Patterns

    Science.gov (United States)

    Hagita, Katsumi; Tominaga, Tetsuo; Hatazoe, Takumi; Sone, Takuo; Takano, Hiroshi

    2018-01-01

    We proposed a filler network toy (FN-toy) model in order to approximately forecast changes in two-dimensional scattering patterns (2DSPs) of nanoparticles (NPs) in crosslinked polymer networks in ultrasmall-angle X-ray scattering (USAXS) experiments under uniaxial elongation. It enables us to estimate the system size dependence of the 2DSP of the NPs. In the FN-toy model, we considered NPs connected by harmonic springs with excluded-volume interactions among the NPs. In this study, we used the NP configurations estimated by reverse Monte Carlo (RMC) analysis for USAXS data observed in SPring-8 experiments on filler-filled styrene butadiene rubber (SBR). In the FN-toy model, we set a bond between every pair of NPs whose distance is less than Cd, where d is the diameter of an NP and C is a parameter that characterizes network properties. We determined the optimal value of C by comparison with 2DSPs of the NPs at 200% elongation for end-modified and unmodified SBR. These 2DSPs are obtained from the results of a large-scale coarse-grained molecular dynamics (CGMD) simulation with 8,192 NPs and 160 million Lennard-Jones (LJ) particles in previous works. For the end-modified SBR, the fitted value is C = 1.367 and for the unmodified SBR, C = 1.258. The difference in C can be regarded as originating from the difference in polymer-NP interactions. We found that the harmonic potential used in the current FN-toy model is not sufficient to reproduce stress-strain curves and local structures of NPs obtained in the previous CGMD simulations, although the FN-toy model can reproduce the 2DSPs. Using the FN-toy model with the fitted value of C, we calculated the 2DSPs of 65,536 and 524,288 NPs, whose initial positions were estimated by RMC analysis for the same USAXS data. It was found that CGMD simulations with 10 billion LJ particles and 524,288 NPs can provide a high-resolution 2DSP that is comparable to the 2DSP observed in USAXS experiments.

  17. Natural rubber: leather composites

    Directory of Open Access Journals (Sweden)

    K. Ravichandran

    2005-06-01

    Full Text Available Leather is a fibrous protein consisting of collagen in a three dimensionally crosslinked network. Chrome tanning of leather improves the appearance of leather but at the same time emits both solid and liquid chrome leather wastes. Scrap rubber recycling using untreated and neutralized leather fibrous particles in natural rubber has been studied. Vulcanization, mechanical, morphological and swelling properties of the natural rubber - scrap rubber composites containing neutralized leather have been discussed. Use of chrome leather particles has been found to improve the consumption of scrap rubber powder in natural rubber formulations. Polymer composites based on leather wastes as fillers are reported to be useful for many applications such as in construction materials, automobile interior moldings, heat and sound insulating boards, shoe soles, flooring materials and moldings with good anti-static properties, air permeability and good appearances.

  18. Toxicity of Pyrolysis Gases from Elastomers

    Science.gov (United States)

    Hilado, Carlos J.; Kosola, Kay L.; Solis, Alida N.; Kourtides, Demetrius A.; Parker, John A.

    1977-01-01

    The toxicity of the pyrolysis gases from six elastomers was investigated. The elastomers were polyisoprene (natural rubber), styrene-butadiene rubber (SBR), ethylene propylene diene terpolymer (EPDM), acrylonitrile rubber, chlorosulfonated polyethylene rubber, and polychloroprene. The rising temperature and fixed temperature programs produced exactly the same rank order of materials based on time to death. Acryltonitrile rubber exhibited the greatest toxicity under these test conditions; carbon monoxide was not found in sufficient concentrations to be the primary cause of death.

  19. 214 VARIATIONS IN THE FIBRE LENGTH OF RUBBER WOOD ...

    African Journals Online (AJOL)

    2010-09-02

    . Nigerian grown rubber in south eastern state of Abia, so as to relate the wood quality with a range of industrial usefulness of the species and the possibility of controlling the wood fibre features silviculturally and genetically.

  20. The Current Situation and the Development Strategies of Rubber

    OpenAIRE

    HUANG, Huide; Zhang, Wanzhen; Zhang, Xizhu; HUANG, Haolun

    2014-01-01

    This article describes the distribution, member structure and industrial operation structure of the rubber farmer cooperatives in Hainan Province, and points out some problems in the cooperatives, such as small member scale, unbalanced regional development, lack of standardization in operation, and industrial operation structure imbalance. Finally some development strategies are put forward as follows: building large-scale cooperatives; attaching importance to the development of rubber farmer...

  1. Polypropylene/ethylene-propylene rubber (PP/EPR blends for the automotive industry: Basic correlations between EPR-design and shrinkage

    Directory of Open Access Journals (Sweden)

    G. D. Potter

    2014-04-01

    Full Text Available The influence of the phase morphology on the shrinkage of injection molded plates from reactor based PP/EPR blends was investigated using a model series. The morphology of the dispersed phase – in terms of size and shape of the rubber particles as determined from scanning electron microscopy (SEM – was found to correlate fairly well with the shrinkage determined in the flow and transverse direction of injection molded plates. In this respect it turned out to be elementary to consider the anisotropy of the particles rather than their average size alone. Additionally, the effect of the EPR design on the coefficient of linear thermal expansion (CLTE was evaluated and brought into a relationship with the blend morphology.

  2. Allergic reactions to rubber condoms.

    OpenAIRE

    Rademaker, M; Forsyth, A

    1989-01-01

    With the increased use of condoms, contact dermatitis to rubber is being seen more often. To develop a rubber condom suitable for use by rubber sensitive people, a "hypoallergenic" condom, which is washed in ammonia to reduce the residues of rubber accelerators, has been manufactured. Fifty patients allergic to various rubber accelerators were patch tested with an ordinary condom and the new washed condom. Fifty patients undergoing routine patch test investigation who were not allergic to rub...

  3. Sugarcane bagasse ash: new filler to natural rubber composite

    Directory of Open Access Journals (Sweden)

    Renivaldo José dos Santos

    2014-12-01

    Full Text Available Waste recycling has been the subject of numerous scientific researches regarding the environmental care. This paper reports the redirecting of sugarcane bagasse ash (SBA as new filler to natural rubber (NR/SBA. The NR/SBA composites were prepared using an opened cylinder mixer to incorporate the vulcanization agents and different proportions of residue (SBA. The ash contains about 70-90% of inorganic compounds, with silica (SiO2 being the main compound. The SBA incorporation improved the mechanical properties of the vulcanized rubber. Based on these results, a new use is proposed for the agro-industry organic waste to be implemented in the rubber vulcanization process, aimed at improving the rubber physical properties as well as decreasing the prices of natural rubber composites.

  4. Radiation vulcanization of natural rubber latex sensitized with commercial gases

    Energy Technology Data Exchange (ETDEWEB)

    Chirinos, H.; Lugao, A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

    2002-07-01

    The industrial activities using natural rubber latex are fully compatible with rural areas in Amazon and other places in Brazil, as well as in other tropical countries. However the classical sulfur vulcanization presents many occupational problems for the workers in rural areas. Radiation vulcanization of natural rubber latex is a much more friendly process as sulfur compounds are not needed for crosslinking, although chemicals as acrylate monomers, particularly multifunctional acrylates are still used as sensitizers for radiation processes. Two commercial gases, acetylene and butadiene, were selected as sensitizers for the radiation vulcanization of natural rubber latex instead of acrylates. These gases accelerate the crosslinking rates of the cure process and lower the radiation dose required to achieve vulcanization of natural rubber latex and improve the mechanical properties to reduce the tackiness of rubber goods. (author)

  5. The rubber tree genome shows expansion of gene family associated with rubber biosynthesis.

    Science.gov (United States)

    Lau, Nyok-Sean; Makita, Yuko; Kawashima, Mika; Taylor, Todd D; Kondo, Shinji; Othman, Ahmad Sofiman; Shu-Chien, Alexander Chong; Matsui, Minami

    2016-06-24

    Hevea brasiliensis Muell. Arg, a member of the family Euphorbiaceae, is the sole natural resource exploited for commercial production of high-quality natural rubber. The properties of natural rubber latex are almost irreplaceable by synthetic counterparts for many industrial applications. A paucity of knowledge on the molecular mechanisms of rubber biosynthesis in high yield traits still persists. Here we report the comprehensive genome-wide analysis of the widely planted H. brasiliensis clone, RRIM 600. The genome was assembled based on ~155-fold combined coverage with Illumina and PacBio sequence data and has a total length of 1.55 Gb with 72.5% comprising repetitive DNA sequences. A total of 84,440 high-confidence protein-coding genes were predicted. Comparative genomic analysis revealed strong synteny between H. brasiliensis and other Euphorbiaceae genomes. Our data suggest that H. brasiliensis's capacity to produce high levels of latex can be attributed to the expansion of rubber biosynthesis-related genes in its genome and the high expression of these genes in latex. Using cap analysis gene expression data, we illustrate the tissue-specific transcription profiles of rubber biosynthesis-related genes, revealing alternative means of transcriptional regulation. Our study adds to the understanding of H. brasiliensis biology and provides valuable genomic resources for future agronomic-related improvement of the rubber tree.

  6. Demonstration/Validation of Hazardous Air Pollutant-Free Adhesive Replacement for Federal Specification MMM-A-1617 Used on the M109A6 Paladin Heavy Brigade Combat Vehicle

    Science.gov (United States)

    2013-09-01

    perimeter of the hatch door. ......................................6 Figure 5. Adhesive application on rubber seal (left) and aluminum channel...natural rubber base, synthetic natural (polyisoprene), styrene butadiene ( SBR ), reclaim, or combination. • Type II: Oil-resistant polychloroprene rubber ...FA-1051) for specification MMM-A-1617 with the HAP- free alternative (3M-847). The specific application was to replace the rubber gasket of the

  7. Mortalidade por câncer em trabalhadores da indústria da borracha de São Paulo Cancer mortality among rubber industry workers in São Paulo, Brazil

    Directory of Open Access Journals (Sweden)

    Hélio Neves

    2006-04-01

    Full Text Available OBJETIVO: Avaliar as mortes por câncer em trabalhadores da indústria da borracha de acordo com o tamanho da empresa. MÉTODOS: Coorte histórica com 9.188 trabalhadores masculinos, matriculados em sindicato de trabalhadores da indústria de borracha do Estado de São Paulo entre 1975 e 1985, sobreviventes em janeiro de 1990 e acompanhados até o final de 2000. As mortes por câncer foram comparadas internamente à coorte, cujos membros foram subdivididos em estratos por porte e sub-ramo da empresa, setor de trabalho e qualificação profissional. A abordagem por conjuntos de risco e regressão logística condicional foi utilizada para o cálculo dos riscos relativos, ajustados por idade, tempo desde o primeiro emprego e tempo de trabalho na indústria da borracha. RESULTADOS: Quando comparados aos empregados de grandes empresas, trabalhadores de pequenas empresas mostraram excesso de mortes por todos tipos de câncer (RR=2,33; IC 95%: 0,90-6,03; tumores de estômago (RR=3,47; IC 95%: 2,57-4,67 e do trato aero-digestivo superior (RR=2,49; IC 95%: 1,78-3,48. Identificou-se excesso de mortes por câncer nos trabalhadores dos setores de manutenção (RR=2,23; IC 95%: 0,73-6,76; expedição, armazenamento e transporte (RR=2,97; IC 95%: 0,77-11,38; e produção (RR=3,51; IC 95%: 1,07-11,57, comparados aos trabalhadores dos setores administrativos. CONCLUSÕES: Os resultados mostram evidências de aumento do risco de tumores de estômago e do trato aero-digestivo superior e, possivelmente, por câncer em geral em trabalhadores de empresas de pequeno porte da indústria da borracha quando comparados aos trabalhadores das grandes empresas.OBJECTIVE: To investigate cancer deaths among rubber industry workers according to company size. METHODS: This historical cohort study included 9,188 male workers, engaged as members of a workers' union in São Paulo, Southeastern Brazil, between 1975 and 1985, alive in January 1990 and followed until the end of 2000

  8. Occupational vitiligo due to unsuspected presence of phenolic antioxidant byproducts in commercial bulk rubber

    Energy Technology Data Exchange (ETDEWEB)

    O' Malley, M.A.; Mathias, C.G.; Priddy, M.; Molina, D.; Grote, A.A.; Halperin, W.E.

    1988-06-01

    We investigated the occurrence of cutaneous depigmentation (vitiligo) among employees of a company that manufactured hydraulic pumps. The interiors of these pumps were injection-molded with rubber. We identified a small but significant cluster of vitiligo cases among a group of employees who frequently handled the rubber used in this injection molding process. Although none of the additives specified in the rubber formulations was a phenolic or catecholic derivative, known to be potential causes of chemically induced vitiligo, gas chromatographic analysis identified a para-substituted phenol (2,4-di-tert-butylphenol, DTBP) in solid samples of the most frequently used rubber. Surface wipe analysis confirmed that workers could be exposed to DTBP from simple handling of the rubber. We subsequently established that the solid bulk rubber used as the base in these stock rubber formulations contained both DTBP and smaller quantities of p-tert-butylphenol. Both had formed as unsuspected byproducts during chemical synthesis of two antioxidants added to the solid bulk rubber by a major rubber supplier. We conclude that the unsuspected presence of potential chemical depigmenting agents in solid bulk rubber, from which industrial rubber products are formulated, may contribute to the occurrence of occupational vitiligo, and that a simple review of ingredients in rubber formulations is inadequate to detect their presence.

  9. Preparation of magnetic rubber with high mechanical properties by latex compounding method

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Chunlin [Shanxi Province Key Laboratory of Functional Nanocomposites, North University of China, Taiyuan 030051 (China); College of Materials Science and Engineering, North University of China, Taiyuan 030051 (China); Gao, Li; Yu, Hailing [Shanxi Province Key Laboratory of Functional Nanocomposites, North University of China, Taiyuan 030051 (China); Sun, Youyi, E-mail: syyi@pku.edu.cn [Shanxi Province Key Laboratory of Functional Nanocomposites, North University of China, Taiyuan 030051 (China); College of Materials Science and Engineering, North University of China, Taiyuan 030051 (China); Yao, Junru; Zhao, Guizhe [Shanxi Province Key Laboratory of Functional Nanocomposites, North University of China, Taiyuan 030051 (China); Liu, Yaqing, E-mail: lyqzgz2010@163.com [Shanxi Province Key Laboratory of Functional Nanocomposites, North University of China, Taiyuan 030051 (China); College of Materials Science and Engineering, North University of China, Taiyuan 030051 (China)

    2016-06-01

    the magnetic rubber based on Fe{sub 3}O{sub 4} nanoparticles and nature rubber were prepared by latex compounding method, in which stable Fe{sub 3}O{sub 4} aqueous solutions were mixed with natural rubber latex and additives. This process was fast, versatile, reliable, safe, environmentally friendly and inexpensive. What’s more, it was found that the magnetic and mechanical properties of magnetic rubber increased together with increase in doping content of Fe{sub 3}O{sub 4} nanoparticles. Especially, it was demonstrated that the tensile strength (25.0 Mpa) of magnetic rubber was improved to be 478.0% comparing to neat natural rubber (5.2 Mpa), which was 5 times higher than maximal value reported in previous work. At the same time, the magnetic rubber revealed better thermal stability and solvent resistance comparing to the neat natural rubber, too. The work dose not only provides a new way to environmentally friendly preparation of magnetic rubber at low temperature, but also improve the mechanical and magnetic properties of magnetic rubber applied in industry. - Highlights: • The magnetic rubber was prepared by a latex compounding method. • The magnetic rubber exhibited high mechanical properties. • The mechanism of high mechanical properties was investigated by the NMR.

  10. A comparison of flexural strengths of polymer (SBR and PVA) modified, roller compacted concrete.

    Science.gov (United States)

    Karadelis, John N; Lin, Yougui

    2015-09-01

    This brief article aims to reveal the flexural performance, including the equivalent flexural strength of PVA (Polyvinyl Alcohol) modified concrete by comparing it primarily with that of SBR (Styrene Butadiene Rubber) concrete. This data article is directly related to Karadelis and Lin [6].

  11. A comparison of flexural strengths of polymer (SBR and PVA modified, roller compacted concrete

    Directory of Open Access Journals (Sweden)

    John N. Karadelis

    2015-09-01

    Full Text Available This brief article aims to reveal the flexural performance, including the equivalent flexural strength of PVA (Polyvinyl Alcohol modified concrete by comparing it primarily with that of SBR (Styrene Butadiene Rubber concrete. This data article is directly related to Karadelis and Lin [6].

  12. Pilot scale experiment on aeration control system for upgrading single-stage activated sludge process for latex rubber industrial wastewater: Phase I:operational problems of using online sensors

    Directory of Open Access Journals (Sweden)

    Wanrudee Wanseng

    2006-07-01

    Full Text Available The aim of this experiment was to upgrade the operation of conventional activated sludge treatment plants to save aeration energy and at the same time to provide better utilization of existing plant capacity for nutrient removal without major financial investment. In this study, pilot-scale experiments of the single stage activated sludge process (ASP as operated in existing ASP in southern Thailand, were investigated under conditions of simultaneous nitrification-denitrification. This first stage of the experiments was to observe the possibility of using oxidation-reduction potential (ORP for aeration control in treatment plant fed with the wastewater from the latex rubber industry. Wastewater from the representative factory contained high carbon and solids. The F/M ratio was up to 1.5 kg of COD/day/kg of MLSS. The results proved that the ORP was greatly affected by the change in air supply. However, it was also affected by the fluctuation of wastewater temperature, which contributed to the bulking sludge problem.

  13. Improved properties of dissimilar rubber-rubber blends using plasma polymer encapsulated curatives : a novel surface modification method to improve co-vulcanization

    NARCIS (Netherlands)

    Guo, R.

    2009-01-01

    In industrial applications, different rubber types are often blended to fine-tune or optimize the property portfolio required for successful performance of articles. Considering the complexity of a rubber blend compound, wherein numerous additives are involved, vulcanization or cure mismatch often

  14. Microcellular foaming of silicone rubber with supercritical carbon dioxide

    Energy Technology Data Exchange (ETDEWEB)

    Hong, In-Kwon; Lee, Sangmook [Dankook University, Youngin (Korea, Republic of)

    2014-01-15

    In spite of great concern on the industrial application of microcellular silicone rubber foams, such as in electric and medical devices, only a few works can be found about the foaming of silicone rubber. In this study, microcellular silicone rubber foams with a cell size of 12 µm were successfully prepared with curing by heat and foaming by supercritical CO{sub 2} as a green blowing agent. The microcellular silicone rubber foams exhibited a well-defined cell structure and a uniform cell size distribution. The crosslinking and foaming of silicone rubber was carried out separately. After foaming, the silicone rubber foam was cross-linked again to stabilize the foam structure and further improve its mechanical properties. Foaming process of cross-linked silicone rubber should be designed carefully based on the viscoelastic properties because of its elastic volume recovery in the atmosphere. The basic crosslinking condition for small cell size and high cell density was obtained after investigating the rheological behavior during crosslinking.

  15. Recycling cycle of materials applied to acrylonitrile-butadiene-styrene/policarbonate blends with styrene-butadiene-styrene copolymer addition

    Science.gov (United States)

    Cândido, L. H. A.; Ferreira, D. B.; Júnior, W. Kindlein; Demori, R.; Mauler, R. S.

    2014-05-01

    The scope of this research is the recycling of polymers from mobile phones hulls discarded and the performance evaluation when they are submitted to the Recycling Cycle of Materials (RCM). The studied material was the ABS/PC blend in a 70/30 proportion. Different compositions were evaluated adding virgin material, recycled material and using the copolymer SBS as impact modifier. In order to evaluate the properties of material's composition, the samples were characterized by TGA, FTIR, SEM, IZOD impact strength and tensile strength tests. At the first stage, the presented results suggest the composition containing 25% of recycled material and 5% of SBS combines good mechanical performance to the higher content of recycled material and lower content of impact modifier providing major benefits to recycling plans. Five cycles (RCM) were applied in the second stage; they evidenced a decrease trend considering the impact strength. At first and second cycle the impact strength was higher than reference material (ABS/PC blend) and from the fourth cycle it was lower. The superiority impact strength in the first and second cycles can be attributed to impact modifier effect. The thermal tests and the spectrometry didn't show the presence of degradation process in the material and the TGA curves demonstrated the process stability. The impact surface of each sample was observed at SEM. The microstructures are not homogeneous presenting voids and lamellar appearance, although the outer surface presents no defects, demonstrating good moldability. The present work aims to assess the life cycle of the material from the successive recycling processes.

  16. Reinforcement Effect of Alkali-Hydrolyzed Wheat Gluten and Shear-Degraded Wheat Starch in Carboxylated Styrene-Butadiene Composites

    Science.gov (United States)

    Wheat gluten (WG) and wheat starch (WS) are the protein and carbohydrate obtained from wheat flours. Wheat gluten is not water soluble or dispersible due to its hydrophobic nature. To prepare wheat gluten dispersions, an alkali hydrolysis reaction was carried out to produce a stable aqueous disper...

  17. Morphology and Phase Transitions in Styrene-Butadiene-Styrene Triblock Copolymer Grafted with Isobutyl Substituted Polyhedral Oligomeric Silsesquioxanes (Postprint)

    National Research Council Canada - National Science Library

    Drazowski, Daniel B; Lee, Andre; Haddad, Timothy S

    2007-01-01

    Two symmetric triblock polystyrene-butadiene-polystyrene (SBS) copolymers with different styrene content were grafted with varying amounts of isobutyl-substituted polyhedral oligomeric silsesquioxane (POSS) molecules...

  18. Aggregate structure and effect of phthalic anhydride modified soy protein on the mechanical properties of styrene-butadiene copolymer

    Science.gov (United States)

    The aggregate structure of phthalic anhydride (PA) modified soy protein isolate (SPI) was investigated by estimating its fractal dimension from the equilibrated dynamic strain sweep experiments. The estimated fractal dimensions of the filler aggregates were less than 2, indicating that these partic...

  19. Development of rubber?enriched dandelion varieties by metabolic engineering of the inulin pathway

    OpenAIRE

    Stolze, A.; Wanke, A.; van Deenen, N.; Geyer, R.; PRÜFER, D.; Schulze Gronover, C.

    2017-01-01

    Summary Natural rubber (NR) is an important raw material for a large number of industrial products. The primary source of NR is the rubber tree Hevea brasiliensis, but increased worldwide demand means that alternative sustainable sources are urgently required. The Russian dandelion (Taraxacum koksaghyz Rodin) is such an alternative because large amounts of NR are produced in its root system. However, rubber biosynthesis must be improved to develop T.?koksaghyz into a commercially feasible cro...

  20. Vulcanization of Rubber

    Indian Academy of Sciences (India)

    Vulcanization of Rubber - How to Alter Molecular Structure and Influence Physical Properties. Ch S S R Kumar Avinash M Nijasure. General Article Volume 2 Issue 4 April 1997 pp 55-59. Fulltext. Click here to view fulltext PDF. Permanent link: http://www.ias.ac.in/article/fulltext/reso/002/04/0055-0059. Author Affiliations.

  1. Vulcanization of Rubber

    Indian Academy of Sciences (India)

    plastic. These attractive physical properties of vulcanized rubber have revolutionised its applications. Modern Improvements. The vulcanization process has undergone several modifications since its discovery. A typical process is shown in Box 1. It may be noted that many additives are included. These have been chosen to ...

  2. Influence of Rock Properties on Wear of M and SR Grade Rubber with Varying Normal Load and Sliding Speed

    Directory of Open Access Journals (Sweden)

    Pal Samir Kumar

    2017-09-01

    Full Text Available Rubbers are interesting materials and are extensively used in many mining industries for material transportation. Wear of rubber is a very complex phenomenon to understand. The present study aims to explain the influence of rock properties on wear of M and SR grade rubber used in top cover of conveyor belts. Extensive laboratory experiments were conducted under four combinations of normal load and sliding speed. The wear of both the rubber types were analyzed based on the rock properties like shear strength, abrasivity index and fractal dimension. A fully instrumented testing set up was used to study the wear of rubber samples under different operating conditions. In general, wear was higher for M grade rubber compared to SR grade rubber. Increase in shear strength of rocks depicts decreasing trend for the wear of M and SR grade rubber at lower load conditions. Moreover, a higher load combination displays no definite trend in both the rubbers. The strong correlation between the wear of rubber and frictional power for all rubber-rock combinations has given rise to the parameter A, which reflects the relative compatibility between the rubber and rock. Increase of Cerchar’s Abrasivity Index of rocks shows gradual enhancement in wear for M grade rubber in all the load and speed combinations whereas, it fails in SR grade rubber due to its higher strength. The wear of rubber tends to decrease marginally with the surface roughness of rocks at highest normal load and sliding speed in M grade rubber. However, the wear of M and SR grade rubber is influenced by the surface roughness of rocks.

  3. THERMOOXIDATIVE STUDY OF RAW NATURAL RUBBER FROM BRAZILIAN IAC 300 SERIES CLONES

    Science.gov (United States)

    The improvement of rubber tree species is of key importance due to the worldwide market demand of this renewable material essential for several types of industries. The thermal performance of natural rubber produced from new clones of IAC 300 series, and the Malaysian RRIM 600 clone (used as control...

  4. A study of protein and amino acids in guayule natural rubber

    Science.gov (United States)

    Natural rubber (NR) from Hevea brasiliensis (the Hevea rubber tree) is a critical agricultural material vital to United States industry, medicine, and defense, yet the country is dependent on NR imports to meet domestic needs. Parthenium argentatum (guayule), a woody desert shrub indigenous to the U...

  5. HYDROPHOBIC RECOVERY OF REPEATEDLY PLASMA-TREATED SILICONE-RUBBER .1. STORAGE IN AIR

    NARCIS (Netherlands)

    EVERAERT, EP; VANDERMEI, HC; DEVRIES, J; BUSSCHER, HJ

    1995-01-01

    Silicone rubber is used for a wide variety of biomedical and industrial applications due to its good mechanical properties, combined with a hydrophobic surface. Frequently, however, it is desirable to alter the surface hydrophobicity of silicone rubber. Often this is done by plasma treatments but

  6. Historical and Recent Achievements in the Field of Microbial Degradation of Natural and Synthetic Rubber

    Science.gov (United States)

    Yikmis, Meral

    2012-01-01

    This review intends to provide an overview of historical and recent achievements in studies of microbial degradation of natural and synthetic rubber. The main scientific focus is on the key enzymes latex-clearing protein (Lcp) from the Gram-positive Streptomyces sp. strain K30 and rubber oxygenase A (RoxA) from the Gram-negative Xanthomonas sp. strain 35Y, which has been hitherto the only known rubber-degrading bacterium that does not belong to the actinomycetes. We also emphasize the importance of knowledge of biodegradation in industrial and environmental biotechnology for waste natural rubber disposal. PMID:22504822

  7. SOLUTION TO THE PROBLEM WASTE RUBBER PRODUCTS BY MODIFYING THE ROAD BINDERS

    Directory of Open Access Journals (Sweden)

    P. S. Beliaev

    2014-01-01

    Full Text Available Summary. The article considers the problem of waste rubber industry through their recycling, compelling stakeholders to keep stocks of valuable raw rubber and improve our environment. The questions of the processes of thermal devulcanization of rubber crumb rubber products, and then use the resulting material (reclaimed rubber crumb as a modifier to improve the quality of road binder. The effect of technological parameters devulcanisation thermal (temperature and exposure time on the degree of devulcanization of crumb rubber. The question of the choice of environmentally friendly agents and emollients devulcanisation to speed the process flow. Researches modifications road binder Reclaimed rubber crumbs obtained under different conditions. The degree of influence of the content of reclaimed rubber crumb on the physico-mechanical properties of road binder bitumen BND 60/90. Studies have shown that the physical and mechanical properties of modified bitumen conform to standards of rubber bitumen binders in accordance with the recommendations of the firm "BITREK": introduction regeneration rata crumb rubber binder in the road leads to an increase in the softening temperature and the appearance of elasticity in the binder compared to the original bitumen and the values of penetration and elongation are within acceptable limits. Thus, the use of recycled materials, reduces the cost of producing a binder for pavement compared to peers.

  8. Residual stresses in rubber formed thermoplastic composites

    NARCIS (Netherlands)

    Wijskamp, Sebastiaan; Lamers, E.A.D.; Akkerman, Remko; Brucato, V.

    2003-01-01

    The rubber pressing process is applied for the rapid production of thermoplastic composite products. However, rubber pressed products show geometrical distortions, such as warpage, due to processinduced residual stresses. An experimental study is performed to measure the curvature after rubber

  9. Effect of quaternary ammonium salts in the process of extracting oil filled rubber from latex

    Directory of Open Access Journals (Sweden)

    N. S. Nikulina

    2016-01-01

    Full Text Available Currently, much attention is paid to the improvement of production technology of synthetic rubber. Much attention is given to rubber is produced by emulsion polymerization. This is due to the fact that rubbers produced by emulsion polymerization have a number of positive characteristics, and are widely used in the tire and rubber industry, in composite formulations for various purposes. In recent years, the technology of production of synthetic rubbers are widely used quaternary ammonium salts which are produced on an industrial scale. Application low and high molecular weight quaternary ammonium salts to reduce pollution of environ-mental protection, exclude the use of mineral salts without significant changes in the process flowsheet. It is found that quaternary ammonium salts react with the components of the emulsion system to form insoluble complexes, which are captured produced rubber crumb. However, Applications, quaternary salts in the manufacture of oil-filled rubber in the literature sources have not been given due attention. The study presents the results of research on the effect of the concentration of a coagulating agent, tempera tours and concentration of the dispersed phase in the process of coagulation of latex in the preparation of oil-filled rubber stamps SCS-30 ARKM-15. The concentration of the coagulating agent does not significantly affect the process of separation of the rubber from the latex. The process of isolation rubber latex is advantageously carried out at a reduced temperature. The concentration of the dispersed phase also provides material effect on the coagulation process. The lead researches mouthestablished that produced rubber, rubber compounds and vulcanizates based on these indicators correspond to their requirements.

  10. QENS investigation of filled rubbers

    CERN Document Server

    Triolo, A; Desmedt, A; Pieper, J K; Lo Celso, F; Triolo, R; Negroni, F; Arrighi, V; Qian, H; Frick, B

    2002-01-01

    The polymer segmental dynamics is investigated in a series of silica-filled rubbers. The presence of inert fillers in polymers greatly affects the mechanical and physical performance of the final materials. For example, silica has been proposed as a reinforcing agent of elastomers in tire production. Results from quasielastic neutron scattering and Dynamic Mechanical Thermal Analysis (DMTA) measurements are presented on styrene-ran-butadiene rubber filled with silica. A clear indication is obtained of the existence of a bimodal dynamics, which can be rationalized in terms of the relaxation of bulk rubber and the much slower relaxation of the rubber adsorbed on the filler surface. (orig.)

  11. Application of gamma irradiation for incorporation of rubber powder in the formulations of EPDM and natural rubber; Aplicacao da radiacao gama para incorporacao do po de borracha em formulacoes de borracha natural e EPDM

    Energy Technology Data Exchange (ETDEWEB)

    Kiyan, Ludmila Y.P.; Parra, Duclerc Fernandes; Lugao, Ademar Benevolo, E-mail: ludmilapozzo@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP/CQMA), Sao Paulo, SP (Brazil). Centro de Quimica e Meio Ambiente

    2013-07-01

    The objective of this work was to study the behavior of the recycling of rubber burrs in form of powder, of the rubber industry from EPDM rubber powder and natural rubber with SBR. The rubber powder was irradiated and reused in rubber artifacts formulations for classical vulcanization. The processed material was irradiated using a {sup 60}Co source in doses of 50, 100, 150 and 200 kGy and a dose rate of 5 kGy s-1 at room temperature. The radiation created devulcanization active sites for subsequent integration of the material (rubber powder) in formulations of commercial use. The processes were compared and their products characterized by analytical methods of the physical properties such as strength and elongation. Satisfactory results were found, noting a major spin-off of EPDM chain demonstrated by increased elongation.

  12. PROPERTIES TYRE TREAD RUBBERS DEPENDING ON PARTICULARITY OF RUBBER COMPOUND

    Directory of Open Access Journals (Sweden)

    Z. S. Shashok

    2014-01-01

    Full Text Available Summary. The results of studies of the elastomeric compositions based on natural rubber containing curatives different ratio "curing agent : vulcanization accelerator" listed in this article. Influence of the composition of the vulcanizing group on stress-strain and elastic- deformation properties of tire tread rubber was installed. It has been shown that a significant effect on thermo-oxidative aging of vulcanizates was the composition of the vulcanizing group. Results of studies resistance tread rubber to exposure to elevated temperatures were presented . Vulcanizates differing type and density by varying the cross-linking ratio of "curing agent : vulcanization accelerator" were obtained . Research results in the formation of rubber resistance and crack growth at different temperatures were presented. Revealed that the best education and resistance to tear propagation under normal conditions characterized by rubber ratio "curing agent : vulcanization accelerator" equal to 1.5:1. It has been established that a dynamic endurance study rubbers depends largely on the nature and concentration of the cross-linking cross-links and movable promote increase efficiency due to the grid and reduce the sulfidity rearrangement. During loading mode alternating deformations at elevated temperatures lability of polysulfide bonds negatively affects the performance of rubber, and the decisive role of providing strength and thermal cross-linking. It is shown that the performance of the spatial grid rubbers allow indirectly judge the dynamic vulcanizates endurance and predict performance rubbers at elevated temperatures under conditions of repeated cyclic deformation. Revealed that the vulcanizing system containing sulfur and vulcanization accelerator TBBS 1:2, promotes the formation of the optimal structure of vulcanized rubber , which provides the best resistance to repeated cyclic deformations in the operating temperatures of the tire.

  13. Alternative sources of natural rubber

    NARCIS (Netherlands)

    Mooibroek, H.; Cornish, K.

    2000-01-01

    Rubber (cis-1,4-polyisoprene) is one of the most important polymers naturally produced by plants because it is a strategic raw material used in more than 40,000 products, including more than 400 medical devices. The sole commercial source, at present, is natural rubber harvested from the Brazilian

  14. 214 VARIATIONS IN THE FIBRE LENGTH OF RUBBER WOOD ...

    African Journals Online (AJOL)

    2010-09-02

    Sep 2, 2010 ... Makurdi Benue State. Correspondence: greenwatchinitiative@yahoo.com. ABSTRACT. Variations in the fibre length of rubber wood were investigated to determine suitability of the wood fibres for some industrial utilization. The fibre lengths were sampled according to main effects such as plantations effects ...

  15. Microwave pre-heating of natural rubber using a rectangular wave guide (MODE: TE10

    Directory of Open Access Journals (Sweden)

    Doo-ngam, N.

    2007-11-01

    Full Text Available This paper presents an application of microwave radiation for pre-heating of natural rubbercompounding with various sulphur contents. The natural rubber-compounding was pre-heated by microwave radiation using a rectangular wave guide system (MODE: TE10 operating at frequency of 2.45 GHz in which the power can vary from 0 to 1500 W. In the present work, the influence of power input, sample thickness, and sulphur content were examined after applying microwave radiation to the rubber samples. Results are discussed regarding the thermal properties, 3-D network, dielectric properties and chemical structures. From the result, firstly, it was found that microwave radiation can be applied to pre-heating natural rubber-compounding before the vulcanization process. Secondly, microwave radiation was very useful for pre-heating natural rubber-compounding that has a thickness greater than 5mm. Thirdly, crosslinking in natural rubber-compounding may occurs after pre-heating by microwave radiation though Fourier Transform Infrared Spectroscopy(FTIR. Finally, there a little effect of sulphur content on temperature profiles after applying microwave radiation to the natural rubber-compounding. Moreover, natural rubber-compounding without carbon black showed a lower heat absorption compared with natural rubbercompounding filled carbon black. This is due to the difference in dielectric loss factor. This preliminary result will be useful information in terms of microwave radiation for pre-heating natural rubber-compounding and rubber processing in industry.

  16. Down-Regulation of Small Rubber Particle Protein Expression Affects Integrity of Rubber Particles and Rubber Content in Taraxacum brevicorniculatum

    Science.gov (United States)

    Hillebrand, Andrea; Post, Janina J.; Wurbs, David; Wahler, Daniela; Lenders, Malte; Krzyzanek, Vladislav; Prüfer, Dirk; Gronover, Christian Schulze

    2012-01-01

    The biosynthesis of rubber is thought to take place on the surface of rubber particles in laticifers, highly specialized cells that are present in more than 40 plant families. The small rubber particle protein (SRPP) has been supposed to be involved in rubber biosynthesis, and recently five SRPPs (TbSRPP1–5) were identified in the rubber-producing dandelion species Taraxacum brevicorniculatum. Here, we demonstrate by immunogold labeling that TbSRPPs are localized to rubber particles, and that rubber particles mainly consist of TbSRPP3, 4 and 5 as shown by high-resolution two-dimensional gel electrophoresis and mass spectrometric analysis. We also carried out an RNA-interference approach in transgenic plants to address the function of TbSRPPs in rubber biosynthesis as well as rubber particle morphology and stability. TbSRPP-RNAi transgenic T. brevicorniculatum plants showed a 40–50% reduction in the dry rubber content, but neither the rubber weight average molecular mass nor the polydispersity of the rubber were affected. Although no phenotypical differences to wild-type particles could be observed in vivo, rubber particles from the TbSRPP-RNAi transgenic lines were less stable and tend to rapidly aggregate in expelling latex after wounding of laticifers. Our results prove that TbSRPPs are very crucial for rubber production in T. brevicorniculatum, probably by contributing to a most favourable and stable rubber particle architecture for efficient rubber biosynthesis and eventually storage. PMID:22911861

  17. Down-regulation of small rubber particle protein expression affects integrity of rubber particles and rubber content in Taraxacum brevicorniculatum.

    Directory of Open Access Journals (Sweden)

    Andrea Hillebrand

    Full Text Available The biosynthesis of rubber is thought to take place on the surface of rubber particles in laticifers, highly specialized cells that are present in more than 40 plant families. The small rubber particle protein (SRPP has been supposed to be involved in rubber biosynthesis, and recently five SRPPs (TbSRPP1-5 were identified in the rubber-producing dandelion species Taraxacum brevicorniculatum. Here, we demonstrate by immunogold labeling that TbSRPPs are localized to rubber particles, and that rubber particles mainly consist of TbSRPP3, 4 and 5 as shown by high-resolution two-dimensional gel electrophoresis and mass spectrometric analysis. We also carried out an RNA-interference approach in transgenic plants to address the function of TbSRPPs in rubber biosynthesis as well as rubber particle morphology and stability. TbSRPP-RNAi transgenic T. brevicorniculatum plants showed a 40-50% reduction in the dry rubber content, but neither the rubber weight average molecular mass nor the polydispersity of the rubber were affected. Although no phenotypical differences to wild-type particles could be observed in vivo, rubber particles from the TbSRPP-RNAi transgenic lines were less stable and tend to rapidly aggregate in expelling latex after wounding of laticifers. Our results prove that TbSRPPs are very crucial for rubber production in T. brevicorniculatum, probably by contributing to a most favourable and stable rubber particle architecture for efficient rubber biosynthesis and eventually storage.

  18. Environmentally Friendly Adhesives and Sealants for Army Applications

    Science.gov (United States)

    2008-12-01

    styrene-butadiene rubber ( SBR ), and nitrile. One brush coat of the adhesive material was applied to the prepared surfaces of the rubber strips...Unclassified Title Environmentally Friendly Adhesives and Sealants for Army Applications 3. Author(s) Faye R. Toulan, Felicia Levine, Leslie...TYPE N/A 3. DATES COVERED - 4. TITLE AND SUBTITLE Environmentally Friendly Adhesives And Sealants For Army Applications 5a. CONTRACT NUMBER

  19. Waterborne Polymeric Films.

    Science.gov (United States)

    1979-12-01

    in the preparation of synthetic rubber for tires. Even in the modern world the term SBR rubber is a common phrase. Since the styrene-butadiene...homopolymers (TgI . . Tan).12 For applications requiring toughness and moisture barrier properties, it is frequently desirable to incorporate styrene (12a...acrylic or styrenated acrylics. Other applications may require features attributed to other vinyl containing compounds such as halides (12b), ethers

  20. Study of Polymer Material Aging by Laser Mass Spectrometry, UV-Visible Spectroscopy, and Environmental Scanning Electron Microscopy

    OpenAIRE

    Junien Exposito; Claude Becker; David Ruch; Frédéric Aubriet

    2007-01-01

    Dyed natural rubber (NR) and styrene butadiene rubber (SBR), designed for outdoor applications, were exposed to an accelerated artificial aging in xenon light. The aging results in the deterioration of the exposed surface material properties. The ability of dyed polymers to withstand prolonged sunlight exposure without fading or undergoing any physical deterioration is largely determined not only by the photochemical characteristics of the absorbing dyestuff itself but also by the polymer str...

  1. Robotically enhanced rubber hand illusion.

    Science.gov (United States)

    Arata, Jumpei; Hattori, Masashi; Ichikawa, Shohei; Sakaguchi, Masamichi

    2014-01-01

    The rubber hand illusion is a well-known multisensory illusion. In brief, watching a rubber hand being stroked by a paintbrush while one's own unseen hand is synchronously stroked causes the rubber hand to be attributed to one's own body and to "feel like it's my hand." The rubber hand illusion is thought to be triggered by the synchronized tactile stimulation of both the subject's hand and the fake hand. To extend the conventional rubber hand illusion, we introduce robotic technology in the form of a master-slave telemanipulator. The developed one degree-of-freedom master-slave system consists of an exoskeleton master equipped with an optical encoder that is worn on the subject's index finger and a motor-actuated index finger on the rubber hand, which allows the subject to perform unilateral telemanipulation. The moving rubber hand illusion has been studied by several researchers in the past with mechanically connected rigs between the subject's body and the fake limb. The robotic instruments let us investigate the moving rubber hand illusion with less constraints, thus behaving closer to the classic rubber hand illusion. In addition, the temporal delay between the body and the fake limb can be precisely manipulated. The experimental results revealed that the robotic instruments significantly enhance the rubber hand illusion. The time delay is significantly correlated with the effect of the multisensory illusion, and the effect significantly decreased at time delays over 100 ms. These findings can potentially contribute to the investigations of neural mechanisms in the field of neuroscience and of master-slave systems in the field of robotics.

  2. Pushing the Limits: The Pattern and Dynamics of Rubber Monoculture Expansion in Xishuangbanna, SW China.

    Directory of Open Access Journals (Sweden)

    Huafang Chen

    Full Text Available The rapidly growing car industry in China has led to an equally rapid expansion of monoculture rubber in many regions of South East Asia. Xishuangbanna, the second largest rubber planting area in China, located in the Indo-Burma biodiversity hotspot, supplies about 37% of the domestic natural rubber production. There, high income possibilities from rubber drive a dramatic expansion of monoculture plantations which poses a threat to natural forests. For the first time we mapped rubber plantations in and outside protected areas and their net present value for the years 1988, 2002 (Landsat, 30 m resolution and 2010 (RapidEye, 5 m resolution. The purpose of our study was to better understand the pattern and dynamics of the expansion of rubber plantations in Xishuangbanna, as well as its economic prospects and conservation impacts. We found that 1 the area of rubber plantations was 4.5% of the total area of Xishuangbanna in 1988, 9.9% in 2002, and 22.2% in 2010; 2 rubber monoculture expanded to higher elevations and onto steeper slopes between 1988 and 2010; 3 the proportion of rubber plantations with medium economic potential dropped from 57% between 1988 and 2002 to 47% in 2010, while the proportion of plantations with lower economic potential had increased from 30% to 40%; and 4 nearly 10% of the total area of nature reserves within Xishuangbanna has been converted to rubber monoculture by 2010. On the basis of our findings, we conclude that the rapid expansion of rubber plantations into higher elevations, steeper terrain, and into nature reserves (where most of the remaining forests of Xishuangbanna are located poses a serious threat to biodiversity and environmental services while not producing the expected economic returns. Therefore, it is essential that local governments develop long-term land use strategies for balancing economic benefits with environmental sustainability, as well as for assisting farmers with the selection of land suitable

  3. Nano-reinforcement of tire rubbers: silica-technology for natural rubber : exploring the infuence of non-rubber constituents on the natural rubber-silica system

    NARCIS (Netherlands)

    Sarkawi, S.S.

    2013-01-01

    Natural rubber is a renewable resource material with outstanding properties which offers significant advantages over its counterparts, the fossil-resource synthetic rubbers. In fact, a natural rubber tree is an efficient carbon dioxide sequester. Since natural rubber is a natural product, it is

  4. Solubility Study of Curatives in Various Rubbers

    NARCIS (Netherlands)

    Guo, R.; Talma, Auke; Datta, Rabin; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2008-01-01

    The previous works on solubility of curatives in rubbers were mainly carried out in natural rubber. Not too much information available on dissimilar rubbers and this is important because most of the compounds today are blends of dissimilar rubbers. Although solubility can be expected to certain

  5. Industrialization

    OpenAIRE

    Blundel, Richard

    2016-01-01

    Industrialization, the historical development that saw cheesemaking transformed from a largely craft-based or artisanal activity, often located on a dairy farm, to a production process that, for the most part, takes place in large ‘cheese factories’ or creameries [See ARTISANAL]. The principal features of modern industrialized cheesemaking, which set it apart from traditional approaches include: high production volumes; sourcing of milk from multiple dairy herds; pasteurization and re-balanci...

  6. Industry

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, Lenny; Roy, Joyashree; Delhotal, K. Casey; Harnisch, Jochen; Matsuhashi, Ryuji; Price, Lynn; Tanaka, Kanako; Worrell, Ernst; Yamba, Francis; Fengqi, Zhou; de la Rue du Can, Stephane; Gielen, Dolf; Joosen, Suzanne; Konar, Manaswita; Matysek, Anna; Miner, Reid; Okazaki, Teruo; Sanders, Johan; Sheinbaum Parado, Claudia

    2007-12-01

    This chapter addresses past, ongoing, and short (to 2010) and medium-term (to 2030) future actions that can be taken to mitigate GHG emissions from the manufacturing and process industries. Globally, and in most countries, CO{sub 2} accounts for more than 90% of CO{sub 2}-eq GHG emissions from the industrial sector (Price et al., 2006; US EPA, 2006b). These CO{sub 2} emissions arise from three sources: (1) the use of fossil fuels for energy, either directly by industry for heat and power generation or indirectly in the generation of purchased electricity and steam; (2) non-energy uses of fossil fuels in chemical processing and metal smelting; and (3) non-fossil fuel sources, for example cement and lime manufacture. Industrial processes also emit other GHGs, e.g.: (1) Nitrous oxide (N{sub 2}O) is emitted as a byproduct of adipic acid, nitric acid and caprolactam production; (2) HFC-23 is emitted as a byproduct of HCFC-22 production, a refrigerant, and also used in fluoroplastics manufacture; (3) Perfluorocarbons (PFCs) are emitted as byproducts of aluminium smelting and in semiconductor manufacture; (4) Sulphur hexafluoride (SF{sub 6}) is emitted in the manufacture, use and, decommissioning of gas insulated electrical switchgear, during the production of flat screen panels and semiconductors, from magnesium die casting and other industrial applications; (5) Methane (CH{sub 4}) is emitted as a byproduct of some chemical processes; and (6) CH{sub 4} and N{sub 2}O can be emitted by food industry waste streams. Many GHG emission mitigation options have been developed for the industrial sector. They fall into three categories: operating procedures, sector-wide technologies and process-specific technologies. A sampling of these options is discussed in Sections 7.2-7.4. The short- and medium-term potential for and cost of all classes of options are discussed in Section 7.5, barriers to the application of these options are addressed in Section 7.6 and the implication of

  7. ASSESSMENT OF THE DYNAMIC PROPERTIES OF PLAIN AND RUBBERIZED CONCRETE

    Directory of Open Access Journals (Sweden)

    Ionuţ Ovidiu TOMA

    2015-11-01

    Full Text Available The use of rubber from discarded car tires as an alternative to natural aggregates in concrete may help preventing the complete depletion of natural resources and work towards a sustainable future. Moreover it can significantly reduce the environmental footprint of the construction industry. The assessment of the dynamic properties of a material are very important from the point of view of the energy dissipation capability of the investigated material. This can be determined from the dynamic modulus of elasticity, damping and the loss coefficients of the material. The paper presents the results obtained during an experimental program aimed at assessing the dynamic characteristics of plain and rubberized concrete containing rubber crumbs from discarded car tires. The theoretical background and the investigation methodology are presented with particular application to cylindrical concrete specimens.

  8. EVALUATION OF TIRE RUBBER DISPOSAL IN CONCRETE FOR PAVEMENTS

    Directory of Open Access Journals (Sweden)

    Rosa Cristina Cecche Lintz

    2009-12-01

    Full Text Available The production of waste by the tire industry has been a growing problem, indicating the need for its reuse. More than thirty million tires are discharged per year in Brazil, where regulation for the environment states that for each four new tires, five unusable ones must be adequately disposed by manufacturers and importers. Paving consumes an extremely large quantity of materials, which can be the source of rational application of waste and rejected materials. Research shows that tire rubber can be added to asphalt, which increases its durability and improves pavement quality and safety conditions by absorbing the rubber elastic properties, and also be used for architectural applications, among others. This study deals with the addition of rubber fibers from tire crushing in concrete for roadway pavements in order to provide proper indication about the alternative material disposal through an evaluation of the mechanical behavior of the modified concrete. Different concrete mixes were produced, within which, part of fine aggregates were substituted by tire rubber and mechanical experiment tests were performed, which show that, due to great resistance losses, the disposal of this alternative material in concrete should be considered for light traffic pavements, with the addition of rubber ranging up to 10% in mass.

  9. Flashover Characteristics of Silicone Rubber Sheets under Various Environmental Conditions

    Directory of Open Access Journals (Sweden)

    Arshad

    2016-08-01

    Full Text Available Silicone rubber insulators are replacing the conventional ceramic and porcelain insulators rapidly in power transmission and distribution industry. Very limited field knowledge is available about the performance of silicone rubber insulators in polluted and contaminated environments and therefore need further investigation. A comprehensive analysis of silicone rubber sheets (intended for coating outdoor insulators was carried out in this paper based on experimental results. The main performance parameters analyzed were arc inception voltage and flashover voltage. Dependence of these parameters on equivalent salt deposit density (ESDD, non-soluble salt deposit density (NSDD, relative humidity, ambient temperature, fog rate, dry band formation, dry band location and number of dry bands were investigated extensively. Insulator orientation and its effect on performance were also studied. The authors believe that this paper will provide a comprehensive knowledge about the flashover characteristics of silicone rubber insulators under humid, contaminated and dry band conditions. These results could be used in the selection and design of silicone rubber insulators for polluted environments.

  10. EVALUATION OF TIRE RUBBER DISPOSAL IN CONCRETE FOR PAVEMENTS

    Directory of Open Access Journals (Sweden)

    Rosa Cristina Cecche Lintz

    2009-01-01

    Full Text Available The production of waste by the tire industry has been a growing problem, indicating the need for its reuse. More than thirty million tires are discharged per year in Brazil, where regulation for the environment states that for each four new tires, five unusable ones must be adequately disposed by manufacturers and importers. Paving consumes an extremely large quantity of materials, which can be the source of rational application of waste and rejected materials. Research shows that tire rubber can be added to asphalt, which increases its durability and improves pavement quality and safety conditions by absorbing the rubber elastic properties, and also be used for architectural applications, among others. This study deals with the addition of rubber fibers from tire crushing in concrete for roadway pavements in order to provide proper indication about the alternative material disposal through an evaluation of the mechanical behavior of the modified concrete. Different concrete mixes were produced, within which, part of fine aggregates were substituted by tire rubber and mechanical experiment tests were performed, which show that, due to great resistance losses, the disposal of this alternative material in concrete should be considered for light traffic pavements, with the addition of rubber ranging up to 10% in mass.

  11. On the Fresh/Hardened Properties of Cement Composites Incorporating Rubber Particles from Recycled Tires

    Directory of Open Access Journals (Sweden)

    Alessandra Fiore

    2014-01-01

    Full Text Available This study investigates the ameliorative effects on some properties of cement-based materials which can be obtained by incorporating rubber particles as part of the fine aggregates. The aim is to find out optimal cement composite/mortar mixtures, containing recycled-tyre rubber particles, suitable for specific engineering applications. Different percentages of rubber particles, from 0% to 75%, were used and, for each percentage, the suitable amount of sand was investigated in order to achieve the best fresh/hardened performances. In particular the following characteristics were examined: density, compressive strength, modulus of elasticity, shrinkage, weight loss, flexural behaviour, thermal conductivity, rapid freezing and thawing durability, and chloride permeability. The experimental results were compared with the ones of cement composite specimens without rubber aggregates. Test results show that the proposed rubberized mortar mixes are particularly suitable for some industrial and architectural applications, such as under-rail bearings, road constructions, paving slabs, false facades, and stone backing.

  12. Identification of a Taraxacum brevicorniculatum rubber elongation factor protein that is localized on rubber particles and promotes rubber biosynthesis.

    Science.gov (United States)

    Laibach, Natalie; Hillebrand, Andrea; Twyman, Richard M; Prüfer, Dirk; Schulze Gronover, Christian

    2015-05-01

    Two protein families required for rubber biosynthesis in Taraxacum brevicorniculatum have recently been characterized, namely the cis-prenyltransferases (TbCPTs) and the small rubber particle proteins (TbSRPPs). The latter were shown to be the most abundant proteins on rubber particles, where rubber biosynthesis takes place. Here we identified a protein designated T. brevicorniculatum rubber elongation factor (TbREF) by using mass spectrometry to analyze rubber particle proteins. TbREF is homologous to the TbSRPPs but has a molecular mass that is atypical for the family. The promoter was shown to be active in laticifers, and the protein itself was localized on the rubber particle surface. In TbREF-silenced plants generated by RNA interference, the rubber content was significantly reduced, correlating with lower TbCPT protein levels and less TbCPT activity in the latex. However, the molecular mass of the rubber was not affected by TbREF silencing. The colloidal stability of rubber particles isolated from TbREF-silenced plants was also unchanged. This was not surprising because TbREF depletion did not affect the abundance of TbSRPPs, which are required for rubber particle stability. Our findings suggest that TbREF is an important component of the rubber biosynthesis machinery in T. brevicorniculatum, and may play a role in rubber particle biogenesis and influence rubber production. © 2015 The Authors The Plant Journal © 2015 John Wiley & Sons Ltd.

  13. Rubber extrusion theory and development

    National Research Council Canada - National Science Library

    Crowther, B. G

    1998-01-01

    ... Adjustable Profile Dies Extruder Screw Design 21 22 23 24 24 Acknowledgement Additional References ' 25 25 References from the Rapra Abstracts Database 27 Subject Index 95 1Rubber Extrusion Theo...

  14. USE OF CRUMB RUBBER FROM USED CAR TIRES IN MINERAL ASPHALT MIXES

    Directory of Open Access Journals (Sweden)

    Andrzej Plewa

    2014-11-01

    Full Text Available With the development of the automotive industry the disposal of used tires is constantly growing problem. Storage of waste rubber is associated with a very long period of decomposition of rubber in the natural conditions. Simultaneously new technologies are developed every year, which in the future may significantly promote recycling of this type of materials. The crumb rubbery modification of the road bitumen is the one of the environmentally safe solutions of rubbery decomposition. Improvement of resistance of the crumb rubbery modification of the road asphalt mixtures is the very important ecological aspect of the future. The article presents the results of research on the fatigue life resistance of asphalt concretes AC16P and AC22P with asphalt-rubber binders. The above analyses have been based on the results of tests of fatigue life of mineral-rubber-asphalt mixes determined by the method of prismatic four-point bending (4PB-PR. Mineral-rubber -asphalt mixes have been diversified according to the amount of the additive of rubber fines in asphalt-rubber binder. On the basis of the test results have been proven improvements functional properties mineral-rubber-asphalt mixes compared with mineral-asphalt mixes with unmodified asphalt.

  15. New understanding of microstructure formation of the rubber phase in thermoplastic vulcanizates (TPV).

    Science.gov (United States)

    Wu, Hanguang; Tian, Ming; Zhang, Liqun; Tian, Hongchi; Wu, Youping; Ning, Nanying

    2014-03-21

    The breakup of the rubber phase in an ethylene-propylene-diene monomer (EPDM)/polypropylene (PP) blend at the early stage of dynamic vulcanization is similar to that in an unvulcanized EPDM/PP blend because of the low crosslink density of the EPDM phase. In this work, the minimum size of the rubber phase in the unvulcanized EPDM/PP blend was first calculated by using the critical breakup law of viscoelastic droplets in a matrix. The calculated results showed that the minimum size of the rubber phase in the unvulcanized blend was in the nanometer scale (25-46 nm), not the micrometer scale as reported in many works. Meanwhile, the actual size of the rubber phase in the thermoplastic vulcanizate (TPV) at both the early stage and the final stage of dynamic vulcanization was observed by using peak force tapping atomic force microscopy (PF-AFM). The results indicated that the EPDM phase indeed broke up into nanoparticles at the early stage of dynamic vulcanization, in good agreement with the calculated results. More interestingly, we first revealed that the micrometer-sized rubber particles commonly observed in TPV were actually the agglomerates of rubber nanoparticles with diameters between 40 and 60 nm. The mechanism for the formation of rubber nanoparticles and their agglomerates during dynamic vulcanization was then discussed. Our work provides guidance to control the microstructure of the rubber phase in TPV to prepare high performance TPV products for a wide range of applications in the automobile and electronic industries.

  16. Effects of Running Shoes with Abrasion Resistant Rubber Sole on the Exercise Capacity of the Human Body

    Directory of Open Access Journals (Sweden)

    Bo Wang

    2017-10-01

    Full Text Available With the development of industrialization, rubber has been gradually used in the manufacture of sports equipment for its favourable properties. This study involved the addition of C5 petroleum resin into brominated isobutylene-isoprene rubber (BIIR and butadiene rubber (BR while manufacturing the sole of running shoes. The effects of running shoes with abrasion resistant rubber sole on the exercise capacity of the human body were investigated by analysing the skid resistance and abrasion resistance of the running shoes, and conducting biomechanical study on naked feet and feet wearing the shoes. The results demonstrated that the rubber sole had favourable slip resistance property and mechanical properties such as stretching, abrasion resistance, and hardness. Compared to naked feet, the peak pressure intensity of the whole step of feet wearing the newly developed shoes, was significantly lower than that of feet wearing ordinary shoes. In the future, rubber can bring more comfortable experience because of its favourable properties.

  17. Properties of Concrete Containing Scrap-Tire Rubber

    National Research Council Canada - National Science Library

    Mazyad Al-Fadhli; Jasem Alhumoud

    2017-01-01

    ...–rubber particles as aggregate in concrete is investigated in this study. Tire–rubber particles composed of tire chips, crumb rubber, and a combination of tire chips and crumb rubber, were used to replace mineral aggregates in concrete...

  18. Rubber mixing process and its relationship with bound rubber and crosslink density

    Science.gov (United States)

    Hasan, A.; Rochmadi; Sulistyo, H.; Honggokusumo, S.

    2017-06-01

    This research studied the relationship between bound rubber and crosslink density based on rubber mixing process. Bound rubber was obtained after natural rubber was masticated and mixed with rubber chemicals and filler while crosslink density was collected after rubber compound was vulcanized. Four methods are used and each method refers to four ways of incorporating carbon black during mixing. The first method, after rubber was masticated for 5 minutes, the addition of rubber chemicals and filler was done simultaneously. Rubber was masticated for 1 minute and continued mixing of rubber chemicals and filler where mixing was different from first method. This was the second method. The third method was the same as the second method but the filler used N 660 while in the second method N 330. The last method is not the same as the first and second, the rubber is only masticated for 3 minutes and then mixed with filler and followed by rubber chemicals sequentially. The results showed that bound rubber and crosslink density were influenced by mixing and mastication process. Bound rubber dropped and crosslink density was relatively stable in the first three mixing methods for increasing carbon black at the beginning of the mixing process. Bound rubber and crosslink density stated opposite results in the fourth mixing method. The higher the bound rubber the lower the crosslink density. Without regard to mixing methods, there is a non-linear relationship between bound rubber formation and crosslink density determination

  19. Rubber: new allergens and preventive measures.

    Science.gov (United States)

    Crepy, Marie-Noëlle

    2016-12-01

    Natural rubber latex (NRL) and rubber accelerators are well-known causes of occupational skin diseases. The latest epidemiological data on rubber allergy show that rubber additives are still among the allergens most strongly associated with occupational contact dermatitis, however, a decrease in NRL allergy has been confirmed. A review of recent publications on rubber allergens based on the Pubmed database is presented. New glove manufacturing processes have been developed, such as low-protein natural rubber gloves, vulcanisation accelerator-free gloves, or specific-purpose gloves containing antimicrobial agents or moisturisers. Several websites provide information on allergens found in gloves and/or glove choice according to occupation.

  20. Exposure to mutagenic airborne particulate in a rubber manufacturing plant.

    Science.gov (United States)

    Fracasso, M E; Franceschetti, P; Mossini, E; Tieghi, S; Perbellini, L; Romeo, L

    1999-04-26

    Epidemiological studies conducted in the 1980s revealed that people working in the rubber manufacturing industry had an increased risk of cancer. Even now, workers employed in rubber processing are still at risk despite the measures adopted to improve their working conditions. The aim of the study was to evaluate the presence of a genotoxic risk in a rubber industry and to verify whether or not it was possible to locate the most dangerous position among the different rubber-working processes. The mutagenic activity of airborne particulate was evaluated in samples collected in the mixing department of a rubber manufacturing plant. Ambient air samples were taken over 3-h period in two stable positions near the mixing (Banbury mixer) and calendering areas. Personal air samples were taken over 2-h period during a normal workday from five workers employed in different rubber processing operations (mixing, weighing, calendering, compounding and extruding). The mutagenic activity of the air samples was determined by plate incorporation assay using Salmonella typhimurium strains (TA 98, TA 98NR, TA 100, YG 1021) with and without metabolic activation. Polycyclic aromatic hydrocarbon (PAH) concentrations were determined by high-performance liquid chromatography (HPLC); the presence of other presumable contaminants were carried out by gas chromatography-mass spectrometry (GC-MS). The results showed substantial direct and indirect frameshift mutagenicity in both ambient and personal samples. No mutagenic activity was present in S. typhimurium TA 100, except in the personal sample from a worker employed on the Banbury mixer. HPLC analysis revealed very low concentrations of PAHs. GC-MS analysis showed the presence of compounds such as azulene derivative, 1,2-dihydro-2,2,4-trimethylquinoline, N-methyl N-phenylbenzenamine, diphenylamine, bis(2-ethylhexyl)phthalate and bis(methyl-propyl)phthalate. We conclude that the high levels of mutagenic activity in ambiental and personal

  1. National Innovation System and Disruptive Innovations in Synthetic Rubber and Tire Technology

    Directory of Open Access Journals (Sweden)

    Ray R. Gehani

    2008-01-01

    Full Text Available The current models of National Innovation Systems (NIS are based on interactions and learning across three institutions: government, university and industry. This empirical study of the evolution of innovations in rubber and tire technologies such as the collaborative innovative suppliers (of raw materials and human capital and disruptive rival innovators to the traditional tri-helical model of National Innovation System. This was empirically examined for the evolution of rubber and tire technology and the rise and decline of its innovative region: the Rubber Capital of the World in Akron, Ohio.

  2. Targeted testing with diethylthiourea often reveals clinically relevant allergic contact dermatitis caused by neoprene rubber

    DEFF Research Database (Denmark)

    Dall, Anne B-H; Andersen, Klaus Ejner; Mortz, Charlotte G

    2012-01-01

    Background. Diethylthiourea is widely used in the rubber industry, particularly in neoprene rubber, and may cause allergic contact dermatitis. However, as thiourea allergens are not part of the European baseline series, the diagnosis of allergic contact dermatitis caused by thiourea compounds......, and positive reactions were found in 15% (13/88). Thus, 15% (37/239) had positive patch test reactions to diethylthiourea, all with current clinical relevance and all strong. Conclusion. Clinical suspicion of neoprene rubber allergy and subsequent aimed patch testing with diethylthiourea give a high yield...

  3. Replacement value of rubber seed ( Hevea brasiliensis ) meal for ...

    African Journals Online (AJOL)

    Rubber seed meal (RSM) contains about 28.63% CP but also high in CF (20%). Rubber seed cake was extruded after the extraction of rubber seed oil from the Rubber Seed oil processing Department of Rubber Research Institute of Nigeria, Benin-City. The rubber seed cake was then milled to produce RSM. Soya bean ...

  4. Eco-Certification of Natural Rubber: Demand, Supply, and Potential Implications of Private Global Environmental Governance

    OpenAIRE

    Kennedy, Sean

    2014-01-01

    In recent years, concern over the environmental impacts of natural rubber culti- vation has generated considerable interest in eco-certification, a form of private environ- mental regulation designed to encourage more sustainable land-use practices. This paper explores the emergence and potential sovereignty implications of this approach to envi- ronmental control with an emphasis on the natural rubber industry. I argue that although eco-certification is advocated as a form of networked gover...

  5. Thermodynamic description of performance characteristics pneumatic elastic elements with rubber-cord envelopes

    Science.gov (United States)

    Korneev, S. A.; Korneev, V. S.; Adonin, V. A.

    2017-08-01

    The thermodynamic computational method of pneumatic elements with rubber-cord envelopes geometrical and power characteristics of the different designs used in a buffer systems and the industrial facilities vibro protection, including, petrochemical and oil and gas production is explained. The record of rubber-cord envelope resilient deformation allowed to obtain the valid data having important applied meaning. Temperature effect is reflected in the received defining ratios.

  6. Nylon fabric reinforced natural rubber compound

    Science.gov (United States)

    Kamal, Mazlina Mustafa; Ismail, Ismaliza

    2017-12-01

    Rubber fabric coated is a unique rubber-textile composite, in which technical textile acts as reinforcing material and strength providing material. In rubber textile composite, rubber to fabric adhesion plays the most critical role for determining assembly process and ultimate strength of product. A vulcanisable adhesive for rubber to fabric fabrication of composite material was developed which compatible with rubber as well as fabric. Evaluation of bonding system with respect to peel strength, shear adhesion strength and weave pattern of fabrics were the major determining criteria for selection and optimization of fabric for rubber hose application. Thus adhesive Cohedure with characteristics of high adhesive strength in Natural Rubber Polyester Fabric compound has been developed.

  7. Advances in rubber/halloysite nanotubes nanocomposites.

    Science.gov (United States)

    Jia, Zhixin; Guo, Baochun; Jia, Demin

    2014-02-01

    The research advances in rubber/halloysite nanotubes (rubber/HNTs) nanocomposites are reviewed. HNTs are environmentally-friendly natural nanomaterials, which could be used to prepare the rubber-based nanocomposites with high performance and low cost. Unmodified HNTs could be adopted to prepare the rubber/HNTs composites with improved mechanical properties, however, the rubber/HNTs nanocomposites with fine morphology and excellent properties were chiefly prepared with various modifiers by in situ mixing method. A series of rubber/HNTs nanocomposites containing several rubbers (SBR, NR, xSBR, NBR, PU) and different modifiers (ENR, RH, Si69, SA, MAA, ILs) have been investigated. The results showed that all the rubber/HNTs nanocomposites achieved strong interfacial interaction via interfacial covalent bonds, hydrogen bonds or multiple interactions, realized significantly improved dispersion of HNTs at nanoscale and exhibited excellent mechanical performances and other properties.

  8. 75 FR 57980 - Polychloroprene Rubber From Japan

    Science.gov (United States)

    2010-09-23

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Polychloroprene Rubber From Japan AGENCY: United States International Trade Commission. ACTION... whether revocation of the antidumping duty finding on polychloroprene rubber from Japan would be likely to...

  9. Electrospinning of PVC with natural rubber

    Energy Technology Data Exchange (ETDEWEB)

    Othman, Muhammad Hariz; Abdullah, Ibrahim [Department of Chemistry, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Mohamed, Mahathir [Radiation Processing Technology Division (BTS), Malaysian Nuclear Agency, Bangi, 43000, Kajang (Malaysia)

    2013-11-27

    Polyvinyl chloride (PVC) was mixed with natural rubbers which are liquid natural rubber (LNR), liquid epoxidised natural rubber (LENR) and liquid epoxidised natural rubber acrylate (LENRA) for a preparation of a fine non-woven fiber’s mat. PVC and each natural rubbers(PVC:LENR, PVC:LNR and PVC:LENRA) were mixed based on ratio of 70:30. Electrospinning method was used to prepare the fiber. The results show that the spinnable concentration of PVC/ natural rubber/THF solution is 16 wt%. The morphology, diameter, structure and degradation temperature of electrospun fibers were investigated by scanning electron microscopy (SEM) and thermogravimetric analysis (TGA). SEM photos showed that the morphology and diameter of the fibers were mainly affected by the addition of natural rubber. TGA results suggested that PVC electrospun fiber has higher degradation temperature than those electrospun fibers that contain natural rubber.

  10. Natural rubber producing plants: An overview | Venkatachalam ...

    African Journals Online (AJOL)

    ... Hevea and also other natural rubber producing species for alternative source of latex production in the near future. Keywords: Alternative rubber sources, biotechnology, breeding, Hevea brasiliensis, Parthenium argentatum, Taraxacum koksaghyz, Ficus bengalensis, Lactuca serriola. African Journal of Biotechnology Vol.

  11. Evaluation of polybutadiene rubbers using FTIR spectra

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, L.N.; Schimidt, F., E-mail: lucas@ifg.edu.br [Instituto Federal de Educacao, Ciencia e Tecnologia de Goias (IFG), Goiania, GO (Brazil); Antonio, P.L.; Caldas, L.V.E. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Vieira, S.L. [Universidade Federal de Goias (UFG), Goiania, GO (Brazil). Instituto de Fisica

    2017-09-01

    Radiation dosimetry for medical and industrial purposes has increasingly evolved over the last few decades with the introduction of various new detectors. Depending on the properties exhibited for radiation dosimetry, some detectors present their applications in a specific area. From a physics point of view, an ideal dosimeter should be able to measure absorbed dose. In this work, synthetic materials based on polybutadiene rubbers (PBR) were proposed as a new class of radiation detectors. The influence of radiation dose on their properties has been investigated for application in radiation dosimetry. The rubber samples were exposed to absorbed doses from 10 Gy up to 250 Gy, using a {sup 60}Co Gamma Cell-220 system. Their responses were carried out with a Fourier Transform Infrared (FTIR) Spectrometer to investigate the presence of absorbance peaks. The results suggested the existence of a relationship between the absorbed doses and the absorbance peaks associated with stretching (1300-1200 cm{sup -1}), deformation (1450-1340 cm{sup -1}) and vibration (1500-1400 cm{sup -1}) processes in the material. (author)

  12. Application of gamma irradiation for incorporation of rubber powder in the formulations of acrylonitrile-butadiene rubber (NBR)

    Energy Technology Data Exchange (ETDEWEB)

    Kiyan, Ludmila Y.P.; Parra, Duclerc Fernandes, E-mail: ludmilapozzo@gmail.com [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Quimica e Meio Ambiente (CQMA)

    2013-07-01

    Full text: Polymeric materials do not decompose easily, disposal of waste polymers is a major environmental problem of global character. Recycling is an economical alternative and environmentally recommended for polymers consumed and discarded by society. As regards the rubber in object, its natural decomposition is much slower due to their highly crosslinked, in three-dimensional networks, structures which makes it an infusible and insoluble material. Moreover, these three dimensional structures entails several problems for their recovery and reprocessing. The aim of this paper was to study the behavior of NBR rubber recycle. It was used rubber powder from industry. The powder was irradiated in master-batch composition and used directly in classical formulations for rubber vulcanization. The master-batch processed was irradiated at doses of 50, 100 and 150kGy in {sup 60}Co source at 5 kGy s{sup -1} rate, at room temperature. Gamma radiation created active sites during devulcanization that promoted further integration of the rubber powder in formulations for commercial use. The processes were compared and their products were characterized by analytical methods of the physical properties such as tensile strength and elongation. The greatest change in the properties of polymeric materials by exposure to ionizing radiation resulted mainly of two main reactions occurring in the polymer molecule: chains scission (degradation) and crosslinking. Although these two processes occur simultaneously in all the polymers, the predominance of one or other effect depends mainly of the chemical structure of each polymer, and the irradiation conditions. In the results was observed the behavior of nitrile rubber under different doses and radiation improvement of the mechanical properties. (author)

  13. Mathematical characterization of values of rheological variables during the networking reaction of rubber mixtures based on SBR

    Science.gov (United States)

    Seliga, E.; Bošák, O.; Rusnáková, S.; Minárik, S.; Tóth, M.

    2015-04-01

    The article presents an analysis of cross-linking reaction using measurements of time dependencies of torque at constant temperature from the range 100 up to 200 °C. The measured results obtained on sample based on styrene - butadiene (SBS) prepared in the laboratory show the behaviour which can be well described by equations of chemical reactions of first-order kinetics. It is possible mathematically describe significant constants of the kinetics of networking reaction (induction period, reaction rate coefficient) by the solution of differential equations and by mathematical approximation. Constants are exponentially dependent on the temperature of vulcanization, while dependencies are Arrhenius like. Math description allows describe the progress of the vulcanization reaction also in the temperature range outside of the monitoring interval, i.e. in the area of extremely long times required for the realization of the cross-linking reaction.

  14. Influence of Adhesive System on Performance of SiO/C Lithium-ion Battery

    Directory of Open Access Journals (Sweden)

    Teng Xin

    2015-01-01

    Full Text Available Silicon based anode material is turning into the research hot point of lithium-ion battery material field due to Si inside supporting higher capacity. Furthermore binder applied as major accessory material of anode system could bring anode material & current collector together, thus the influence given by binder system to battery performance becomes the key point. The paper describes the procedure of adopting commercial LiCoO2 SiO/C as composite material & electrolyte, with using styrene butadiene rubber and acrylic acid copolymer as binder to figure out lithium-ion battery with 2.5Ah, which is testified to present better performance on cold temperature & cycle life plus having a little bit swelling compared with the lithium-ion battery using only styrene butadiene rubber as binder.

  15. Enhancing natural rubber ( Hevea brasiliensis production through ...

    African Journals Online (AJOL)

    The study investigated extension activities in natural rubber production in South West Zone of Nigeria. Fifty rubber farmers randomly selected from five communities in the rubber belt sub-zone were sampled. A structured interview schedule was used in collecting data from the respondents.Statistical analysis was ...

  16. 75 FR 38119 - Polychloroprene Rubber From Japan

    Science.gov (United States)

    2010-07-01

    ... COMMISSION Polychloroprene Rubber From Japan AGENCY: United States International Trade Commission. ACTION: Institution of a five-year review concerning the antidumping duty finding on polychloroprene rubber from Japan... antidumping duty finding on polychloroprene rubber from Japan would be likely to lead to continuation or...

  17. Calamus deerratus fibre reinforced natural rubber vulcanizates ...

    African Journals Online (AJOL)

    This research study investigates the potentials of Calamus deerratus fibre (CDF) as a reinforcing filler in natural rubber, Standard Nigerian Rubber (SNR10) vulcanizates. The Calamus deerratus was cut, dried, pulverized, characterized and incorporated into the natural rubber compounds and the effects on the cure ...

  18. Morphology, Tensile Strength and Oil Resistance of Gum Rubber Sheets Prepared from Lignin Modified Natural Rubber

    Directory of Open Access Journals (Sweden)

    Asrul M.

    2014-07-01

    Full Text Available The paper describes the preparation of lignin filled natural rubber latex composite and its subsequent use to obtain lignin modified rubber. Two types of lignin i.e.: rubber wood and commercial alkali lignin were used as rubber filler. Gum rubber sheets were prepared from the lignin modified rubber and their properties were compared to Standard Malaysian Rubber (SMR 20 and a type of rubber obtained from the coagulation of high ammonia latex. Rubber morphology was investigated using Scanning Electron Microscope on the cross-sectional area of cryo-fractured samples. Oil resistance of the rubber sheets was determined by measuring the mass change before and after ASTM IRM 903 oil immersion, while the tensile strengths were determined according to ASTM D412 standard. Low values of tensile strength obtained for the commercial alkali lignin modified rubber sheet relative to the rest of the rubber samples was attributed to poor lignin dispersion. This occurrence was substantiated by the SEM analysis of cryo-fractured samples where crazes and inhomogeneity was observed. Nonetheless, both lignin modified rubbers exhibited higher level of oil resistance compared to SMR 20. This is due to the nature of lignin as a hydrophilic component and its presence in the rubber matrix complicates the oil diffusion process into rubber.

  19. Through the Technology Lens: The Expansion of Rubber and its Implications in Montane Mainland Southeast Asia

    Directory of Open Access Journals (Sweden)

    Jefferson Fox

    2014-01-01

    Full Text Available Natural latex from the rubber tree (Hevea brasiliensis is a hot commodity, with consumption increasing worldwide at an average rate of 5.8% per year since 1900. The vast majority of the world′s rubber supply has historically come from the wet-humid tropics of Southeast Asia, but researchers in China have successfully developed new hybrids that grow well in areas with cooler temperatures and a distinct dry season. Today, investors are promoting rubber plantations in non-traditional rubber growing areas of Laos, Cambodia, Myanmar, northeast Thailand, and northwest Vietnam. By critically assessing the impacts of this expansion of rubber and clarifying the relationship between tools and technologies, the paper suggests that the widespread adoption of rubber as a technology leads to loss of natural and agricultural biodiversity; greater use of surface and groundwater supplies; increased use of pesticides, fertilisers, and other chemicals; higher exposure to market booms and busts for smallholders and investors; and for some farmers, the loss of their land to industrial plantations on which they may become labourers. The paper argues that if state authorities recognise the double-edged nature of rubber as a technology, they can act to try to limit its damaging effects through polices that recognise secure tenure and encourage small-scale, diversified agroforestry systems.

  20. Thermomechanical behavior of SBR reinforced with nanotubes functionalized with polyvinylpyridine

    Science.gov (United States)

    De Falco, A.; Lamanna, M.; Goyanes, S.; D'Accorso, N. B.; Fascio, M. L.

    2012-08-01

    The mechanical and thermal behavior of composites consisting on a styrene-butadiene rubber (SBR) matrix with a sulphur/accelerator system and multiwalled carbon nanotubes functionalized with poly-4-vinylpyridine (MWCNT-PVP) as reinforcement, were studied. The materials were tested with stress-strain tensile tests, DMTA and DSC for thermal properties. A strong increase in the plastic behavior with slight decrease of its elastic Modulus and Tg led to unexpected results.

  1. Synthesis and Characterization of Polypyrrole Coated SBR Composites

    Science.gov (United States)

    Mathew, Anisha Mary; Neena, P.; Prasanth, S.; Panwar, N. S.; Pradeep, P.

    2008-04-01

    Conducting polymer of styrene butadiene rubber has been synthesized by chemical doping method. Subsequently the samples were coated with an intrinsically conducting polymer shell (ICP) of polypyrrole. The polymer shell was synthesized by chemical route method after the preparation of conducting polymer powder of SBR. The chemical structure of the composite was analyzed by taking the FTIR spectra. Electrical conductivity of the new hybrid material is found to be same as the conductivity of polypyrrole.

  2. Thermomechanical behavior of SBR reinforced with nanotubes functionalized with polyvinylpyridine

    Energy Technology Data Exchange (ETDEWEB)

    De Falco, A. [Universidad de Buenos Aires, FCEyN, Depto. de Fisica, LPyMC, Pabellon I, Buenos Aires 1428 (Argentina); Lamanna, M. [Universidad de Buenos Aires, FCEyN, Depto. de Quimica Organica, Centro de Investigaciones en Hidratos de Carbono (CIHIDECAR) (Argentina); Goyanes, S. [Universidad de Buenos Aires, FCEyN, Depto. de Fisica, LPyMC, Pabellon I, Buenos Aires 1428 (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET) (Argentina); D' Accorso, N.B. [Universidad de Buenos Aires, FCEyN, Depto. de Quimica Organica, Centro de Investigaciones en Hidratos de Carbono (CIHIDECAR) (Argentina); Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET) (Argentina); Fascio, M.L., E-mail: mfascio@qo.fcen.uba.ar [Universidad de Buenos Aires, FCEyN, Depto. de Quimica Organica, Centro de Investigaciones en Hidratos de Carbono (CIHIDECAR) (Argentina)

    2012-08-15

    The mechanical and thermal behavior of composites consisting on a styrene-butadiene rubber (SBR) matrix with a sulphur/accelerator system and multiwalled carbon nanotubes functionalized with poly-4-vinylpyridine (MWCNT-PVP) as reinforcement, were studied. The materials were tested with stress-strain tensile tests, DMTA and DSC for thermal properties. A strong increase in the plastic behavior with slight decrease of its elastic Modulus and Tg led to unexpected results.

  3. Stored energy function of rubberlike materials derived from simple tensile data.

    Science.gov (United States)

    Peng, T. J.; Landel, R. F.

    1972-01-01

    An explicit formulation is developed to obtain the stored energy function, based on the Valanis-Landel separable symmetric stored energy function. This formulation is applicable to any multiaxial stress state, from simple tensile data alone, for those cases in which the stored energy function is a separable function of the stretch ratios. By direct comparison, it is also shown that styrene butadiene rubber, at least over a specific range, follows this postulated separable form.

  4. Improved Mechanical Integrity of ALD-Coated Composite Electrodes for Li-Ion Batteries

    Science.gov (United States)

    2011-01-01

    car- boxymethyl cellulose CMC and styrene butadiene rubber SBR binders,5 and heat-treatment,6 as well as carbon-based matrices.7 However, many of...potential of these coatings for high-energy density Li-ion batteries suitable for vehicular applications . © 2010 The Electrochemical Society. DOI: 10.1149...these methods may be quite difficult to scale for Li-ion battery production for vehicular applications . In our previous work, we showed considerable

  5. Identification of an exposure risk to heavy metals from pharmaceutical-grade rubber stoppers.

    Science.gov (United States)

    Li, Xianghui; Qian, Pingping

    2017-07-01

    Exposure to low concentrations of heavy metals and metalloids represents a well-documented risk to animal and human health. However, current standards (European Pharmacopeia [EP], United States Pharmacopoeia [USP], International Organization for Standardization [ISO], YBB concerned with rubber closures) only require testing for Zn in pharmaceutical-grade rubber stoppers and then using only pure water as a solvent. We extracted and quantified heavy metals and trace elements from pharmaceutical-grade rubber stoppers under conditions that might occur during the preparation of drugs. Pure water, saline, 10% glucose, 3% acetic acid (w/v), 0.1 mol/L hydrochloric acid, and diethylenetriaminepentaacetic acid (4 mg/mL, 0.4 mg/mL, and 0.04 mg/mL) were used as extraction agents. We quantified the extracted arsenic, lead, antimony, iron, magnesium, aluminum, and zinc using inductively coupled plasma mass spectrometry. The concentration of extracted metals varied depending on the different extraction solutions used and between the different rubber stopper manufacturers. Rubber stoppers are ubiquitously used in the pharmaceutical industry for the storage and preparation of drugs. Extraction of heavy metals during the manufacturing and preparation of drugs represents a significant risk, suggesting a need for industry standards to focus on heavy metal migration from rubber stoppers. Copyright © 2016. Published by Elsevier B.V.

  6. Degradation of non-vulcanized natural rubber - renewable resource for fine chemicals used in polymer synthesis

    Directory of Open Access Journals (Sweden)

    Alexander Fainleib

    2013-01-01

    Full Text Available In the current scenario, there is growing interest in the products of degradation of rubber (natural and synthetic for specific applications in different industry sectors, whose benefits in replacing conventionally used products are mainly related to sustainability. Since the degradation products of rubber can be used in different areas, several research groups may have the interest aroused by these products, but are not familiar with the aspects related to the chemical behavior of rubber. This review aims to bring together the key information in the published literature on the degradation of natural rubber, emphasizing metatheses reactions, oxidative damage and splitting of the double bond, in order to serve as a reference source for researchers from different fields interested in obtaining such kind of products. The structures and properties as well as additional chemical transformations resulting in oligomers of isoprene, functionalised oligomers and polymers based on both are also described.

  7. CAN POLITICIANS SPEED UP LONG-TERM TECHNOLOGICAL CHANGE? SOME INSIGHTS FROM A COMPARISON OF THE GERMAN AND US-AMERICAN SYNTHETIC RUBBER PROGRAMS BEFORE, DURING AND AFTER WORLD WAR II

    Directory of Open Access Journals (Sweden)

    Jochen Streb

    2003-01-01

    Full Text Available I investigated the effect of government demand on firms’ innovation activities comparing the German and American synthetic rubber industries before, during and after World War II. I obtained three main results. 1. Because of the low price of natural rubber, price and sales guarantees were needed to motivate firms to produce the synthetic rubber BUNA S. 2. Facing fixed prices I.G. Farben improved their efficiency more than the American firms working under cost plus contracts. 3. The patent sharing agreement of the American synthetic rubber program caused firms to hold back advanced synthetic rubber inventions.

  8. In-depth proteome analysis of the rubber particle of Hevea brasiliensis (para rubber tree).

    Science.gov (United States)

    Dai, Longjun; Kang, Guijuan; Li, Yu; Nie, Zhiyi; Duan, Cuifang; Zeng, Rizhong

    2013-05-01

    The rubber particle is a special organelle in which natural rubber is synthesised and stored in the laticifers of Hevea brasiliensis. To better understand the biological functions of rubber particles and to identify the candidate rubber biosynthesis-related proteins, a comprehensive proteome analysis was performed on H. brasiliensis rubber particles using shotgun tandem mass spectrometry profiling approaches-resulting in a thorough report on the rubber particle proteins. A total of 186 rubber particle proteins were identified, with a range in relative molecular mass of 3.9-194.2 kDa and in isoelectric point values of 4.0-11.2. The rubber particle proteins were analysed for gene ontology and could be categorised into eight major groups according to their functions: including rubber biosynthesis, stress- or defence-related responses, protein processing and folding, signal transduction and cellular transport. In addition to well-known rubber biosynthesis-related proteins such as rubber elongation factor (REF), small rubber particle protein (SRPP) and cis-prenyl transferase (CPT), many proteins were firstly identified to be on the rubber particles, including cyclophilin, phospholipase D, cytochrome P450, small GTP-binding protein, clathrin, eukaryotic translation initiation factor, annexin, ABC transporter, translationally controlled tumour protein, ubiquitin-conjugating enzymes, and several homologues of REF, SRPP and CPT. A procedure of multiple reaction monitoring was established for further protein validation. This comprehensive proteome data of rubber particles would facilitate investigation into molecular mechanisms of biogenesis, self-homeostasis and rubber biosynthesis of the rubber particle, and might serve as valuable biomarkers in molecular breeding studies of H. brasiliensis and other alternative rubber-producing species.

  9. Comparative proteome analysis of rubber latex serum from pathogenic fungi tolerant and susceptible rubber tree (Hevea brasiliensis).

    Science.gov (United States)

    Havanapan, Phattara-Orn; Bourchookarn, Apichai; Ketterman, Albert J; Krittanai, Chartchai

    2016-01-10

    Many cultivated rubber trees (Hevea brasiliensis) are invaded by various Phytophthora species fungi, especially in tropical regions which result in crop yield losses. Comparative proteome analysis coupled with liquid chromatography electrospray/ionization (LC-ESI) mass spectrometry identification was employed to investigate the relative abundance of defense related proteins in Phytophthora sp. susceptible (RRIM600) and tolerant (BPM24) clones of rubber tree. Proteome maps of non-rubber constituent of these two model clones show similar protein counts, although some proteins show significant alterations in their abundance. Most of the differentially abundant proteins found in the serum of BPM24 illustrate the accumulation of defense related proteins that participate in plant defense mechanisms such as beta-1,3-glucanase, chitinase, and lectin. SDS-PAGE and 2-D Western blot analysis showed greater level of accumulation of beta-1,3-glucanase and chitinase in latex serum of BPM24 when compared to RRIM600. A functional study of these two enzymes showed that BPM24 serum had greater beta-1,3-glucanase and chitinase activities than that of RRIM600. These up-regulated proteins are constitutively expressed and would serve to protect the rubber tree BPM24 from any fungal invader. The information obtained from this work is valuable for understanding of defense mechanisms and plantation improvement of H. brasiliensis. Non-rubber constituents (latex serum) have almost no value and are treated as waste in the rubber agricultural industry. However, the serum of natural rubber latex contains biochemical substances. The comparative proteomics analysis of latex serum between tolerant and susceptible clones reveals that the tolerant BPM24 clone contained a high abundance of several classes of fungal pathogen-responsive proteins, such as glucanase and chitinase. Moreover, other proteins identified highlighted the accumulation of defensive-associated proteins participating in plant

  10. Para rubber seed oil: new promising unconventional oil for cosmetics.

    Science.gov (United States)

    Lourith, Nattaya; Kanlayavattanakul, Mayuree; Sucontphunt, Apirada; Ondee, Thunnicha

    2014-01-01

    Para rubber seed was macerated in petroleum ether and n-hexane, individually, for 30 min. The extraction was additionally performed by reflux and soxhlet for 6 h with the same solvent and proportion. Soxhlet extraction by petroleum ether afforded the greatest extractive yield (22.90 ± 0.92%). Although antioxidant activity by means of 1, 1-diphenyl-2-picrylhydrazyl (DPPH) assay was insignificantly differed in soxhleted (8.90 ± 1.15%) and refluxed (9.02 ± 0.71%) by n-hexane, soxhlet extraction by n-hexane was significantly (p cosmetic raw material. Therefore, Para rubber seed oil is highlighted as the promising ecological ingredient appraisal for cosmetics. Transforming of the seed that is by-product of the important industrial crop of Thailand into cosmetics is encouraged accordingly.

  11. Thermomechanical characterisation of cellular rubber

    Science.gov (United States)

    Seibert, H.; Scheffer, T.; Diebels, S.

    2016-09-01

    This contribution discusses an experimental possibility to characterise a cellular rubber in terms of the influence of multiaxiality, rate dependency under environmental temperature and its behaviour under hydrostatic pressure. In this context, a mixed open and closed cell rubber based on an ethylene propylene diene monomer is investigated exemplarily. The present article intends to give a general idea of the characterisation method and the considerable effects of this special type of material. The main focus lies on the experimental procedure and the used testing devices in combination with the analysis methods such as true three-dimensional digital image correlation. The structural compressibility is taken into account by an approach for a material model using the Theory of Porous Media with additional temperature dependence.

  12. Constructing better roads with asphalt rubber

    Directory of Open Access Journals (Sweden)

    Pais Jorge C.

    2015-12-01

    Full Text Available Brazilians mixtures containing asphalt rubber were evaluated by mechanical laboratory tests. A conventional mixture with asphalt CAP-50/70 was produced as a mixture control. With the aim of compare the Brazilians mixtures performance, a Portuguese asphalt rubber mixture was tested as well. The testing set involved the determination of the mechanical properties, fatigue and permanent deformation, of asphalt rubber produced by wet process through two different systems: continuous blend and terminal blend. The asphalt rubber morphology was evaluated in order to determine the compatibility of the systems. The asphalt rubber mixtures exhibit good resistance to permanent deformation and prolonged fatigue life in relation to mixture control. Therefore it is concluded that the application of asphalt rubber alters the characteristics of asphalt mixture in a very beneficial way.

  13. Adding crumb rubber into exterior wall materials.

    Science.gov (United States)

    Zhu, Han; Thong-On, Norasit; Zhang, Xiong

    2002-10-01

    In Arizona US, most houses are built with walls covered by stuccos/coatings/mortars. This paper presents an explorative investigation of adding crumb rubber into stuccos/coatings/mortars. A series of experiments are conducted to examine the thermal and mechanical performance of the crumb rubber mixes. The results show that, the mixes with crumb rubber do exhibit more desirable performances like being high in crack-resistance and thermal insulation, and low in thermal expansion/contraction. The drawback for the crumb rubber mixes is the reduction in compressive strength, but which can be compensated by other means. As a site experiment, an area of 100 square-feet of crumb rubber coatings for two mix designs is sprayed on a tire-adobe wall. After being sprayed more than 14 months, the coatings apparently are in good condition. Significance of this study is that this practice, if accepted, will yield improved products that consume large quantities of crumb rubber.

  14. Prehistoric polymers: rubber processing in ancient mesoamerica

    Science.gov (United States)

    Hosler; Burkett; Tarkanian

    1999-06-18

    Ancient Mesoamerican peoples harvested latex from Castilla elastica, processed it using liquid extracted from Ipomoea alba (a species of morning glory vine), and fashioned rubber balls, hollow rubber figurines, and other rubber artifacts from the resulting material. Chemical and mechanical analyses of the latex and of the processed rubber indicate that the enhanced elastic behavior of the rubber relative to the unprocessed latex is due to purification of the polymer component and to an increase in the strength and number of interchain interactions that are induced by organic compounds present in I. alba. These ancient peoples' control over the properties of latex and processed rubber gave rise to the Mesoamerican ball game, a central ritual element in all ancient Mesoamerican societies.

  15. Identification of Natural Rubber and Characterization of Rubber Biosynthetic Activity in Fig Tree1

    Science.gov (United States)

    Kang, Hunseung; Kang, Min Young; Han, Kyung-Hwan

    2000-01-01

    Natural rubber was extracted from the fig tree (Ficus carica) cultivated in Korea as part of a survey of rubber producing plants. Fourier transform infrared and 13C nuclear magnetic resonance analysis of samples prepared by successive extraction with acetone and benzene confirmed that the benzene-soluble residues are natural rubber, cis-1,4-polyisoprene. The rubber content in the latex of fig tree was about 4%, whereas the rubber content in the bark, leaf, and fruit was 0.3%, 0.1%, and 0.1%, respectively. Gel-permeation chromatography revealed that the molecular size of the natural rubber from fig tree is about 190 kD. Similar to rubber tree (Hevea brasiliensis) and guayule (Parthenium argentatum Gray), rubber biosynthesis in fig tree is tightly associated with rubber particles. The rubber transferase in rubber particles exhibited a higher affinity for farnesyl pyrophosphate than for isopentenyl pyrophosphate, with apparent Km values of 2.8 and 228 μm, respectively. Examination of latex serum from fig tree by sodium dodecyl sulfate-polyacrylamide gel electrophoresis revealed major proteins of 25 and 48 kD in size, and several proteins with molecular mass below 20 and above 100 kD. Partial N-terminal amino acid sequencing and immunochemical analyses revealed that the 25- and 48-kD proteins were novel and not related to any other suggested rubber transferases. The effect of EDTA and Mg2+ ion on in vitro rubber biosynthesis in fig tree and rubber tree suggested that divalent metal ion present in the latex serum is an important factor in determining the different rubber biosynthetic activities in fig tree and rubber tree. PMID:10889262

  16. Chemistry of rubber processing and disposal.

    Science.gov (United States)

    Bebb, R L

    1976-10-01

    The major chemical changes during the processing of rubber occur with the breakdown in mastication and during vulcanization of the molded tire. There is little chemical change during the compounding, calendering, extrusion, and molding steps. Reclaiming is the process of converting scrap rubber into an unsaturated, processible product that can be vulcanized with sulfur. Pyrolysis of scrap rubber yields a complex mixture of liquids, gas, and residue in varying ratios dependent on the nature of the scrap and the conditions of pyrolysis.

  17. Brittle-tough transition in nylon-rubber blends: effect of rubber concentration and particle size

    NARCIS (Netherlands)

    Borggreve, R.J.M.; Gaymans, R.J.; Schuijer, J.; Ingen Housz, J.F.

    1987-01-01

    Blends of nylon-6 and EPDM-rubber were prepared with various rubber contents (0–20 wt%) and particle sizes (0.3–1.6 μm). The effects of rubber concentration and particle size on the tensile modulus, torsion modulus, yield stress and notched impact strength of the blends were studied. Blend

  18. Effect of non-rubber constituents on Guayule and Hevea rubber intrinsic properties

    Science.gov (United States)

    To meet the increasing demand for natural rubber (NR), currently sourced from the tropical rubber tree Hevea brasiliensis, and address price volatility and steadily increasing labor costs, alternate rubber-producing species are in commercial development. One of these, guayule (Parthenium argentatum)...

  19. NITROSO RUBBER RESEARCH, DEVELOPMENT AND PRODUCTION.

    Science.gov (United States)

    COPOLYMERIZATION, VISCOSITY, VULCANIZATION, ANHYDRIDES, SUCCINATES, ANILINES , AROMATIC COMPOUNDS, NITRATES, BENZOIC ACIDS, NITRITES, NITROBENZENES ...FLUORINE COMPOUNDS, *HALOCARBON PLASTICS, *SYNTHETIC RUBBER, SYNTHESIS (CHEMISTRY), PRODUCTION, PRODUCTION, ORGANIC NITROGEN COMPOUNDS, ACETATES

  20. Design of the Nonlinear Pin Rubber Forming Equipment Integrating the Functions of Extruding, Dewatering, Drying & Expanding

    Directory of Open Access Journals (Sweden)

    Yuefeng Yuan

    2014-12-01

    Full Text Available The top priority of car-tire suppliers is to improve wetland grip force of the using tires, reduce the rolling resistance and the rolling noise of tires. It is urgent for the tire industry to research and develop high-performance tires to solve the above problems. They must use the high- performance synthetic rubber and auxiliary rubber to develop the most advanced manufacturing technologies and equipment. Silica, a kind of important tire auxiliary rubber, can significantly reduce the rolling resistance of tires, improve the grip force and properties resistant to ice, wetness or slippery of tires. In this paper, based on the conventional tire rubber forming technologies of extrusion, dewatering, drying and expanding, a study is made on the conical screw, the dewatering barrel, the drying barrel, the pin layout scheme, the expanding die head, cutter and the control system. The nonlinear pin rubber forming equipment integrating the functions of extrusion, dewatering, drying and expanding is designed and applied to tire auxiliary rubber forming. The experiment shows that the forming device can realize the one-step forming, with high forming efficiency, low cost and less labor.

  1. Utilization of Liquid Smoke from Oil Palm Empty Fruit Bunches on Raw Rubber Processing

    Directory of Open Access Journals (Sweden)

    Hidayati Hidayati

    2011-06-01

    Full Text Available Research utilization of liquid smoke from oil palm empty fruit bunches of raw rubber has been made to utilize solid waste from industrial processing of oil palm empty fruit bunches of oil palm so that it becomes economically valuable products. This research has been done by pyrolysis of oil palm empty fruit bunches at a temperature of 400oC for 5, 6, 7 and 8 hours. The results show that the pyrolysis liquid smoke oil palm empty fruit bunches for 8 hours give a high concentration of phenol and acetic acid, respectively 5% and 0.454%. Liquid smoke that has been obtained is used as a coagulant in raw rubber plantation crops of the people residing in the village of Ambawang, Kubu Raya District, West Kalimantan. Results of treatment of liquid smoke on raw rubber  show that the rubber products that have been frozen and dried are superior in terms of color, smell and drying time compared with the treatment of formic acid and water battery which has been added so far on raw rubber by the local rubber farmers.

  2. Effect of synthesized ZnO nanoparticles on thermal conductivity and mechanical properties of natural rubber

    Science.gov (United States)

    Suntako, R.

    2018-01-01

    Zinc oxide (ZnO) is widely used in rubber industry as a cure activator for rubber vulcanization. In this work, comparison of cure characteristic, mechanical properties, thermal conductivity and volume swell testing in oil no.1 and oil no.3 between natural rubber (NR) filled synthesized ZnO nanoparticles (sZnO) by precipitation method and NR filled conventional ZnO (cZnO). The particle size of sZnO is 41.50 nm and specific area of 27.92 m2/g, the particle size of cZnO is 312.92 nm and specific surface area of 1.35 m2/g. It has been found that NR filled sZnO not only improves rubber mechanical properties, volume swell testing but also improves thermal conductivity and better than NR filled cZnO. Thermal conductivity of NR filled sZnO increases by 10.34%, 12.90% and 20.00%, respectively when compared with NR filled cZnO in same loading content (various concentrations of ZnO at 5, 8 and 10 parts per hundred parts of rubber). This is due to small particle size and large specific surface area of sZnO which lead to an increase in crosslinking in rubber chain and enhance heat transfer performance.

  3. Pemanfaatan minyak kulit biji jambu mete sebagai substitusi karet stirena butadiena pada kompon karkas ban kendaraan bermotor

    Directory of Open Access Journals (Sweden)

    Dwi Wahini Nurhajati

    2005-07-01

    Full Text Available Cashew nut shell liquid (CNSL as a by product of cashew nut industry was not utilized. CNSL can be used to produce a rubber-like materials. The objectives of the research was to study the application of CNSL resin as substitute material for styrene butadiene rubber (SBR in the carcass compound. CNSL was reacted with formaldehyde resulting a rubbery CNSL-formaldehyde resin. CNSL –formaldehyde resin was prepared by reaction of 100 parts of CNSL, 5 parts of a 37% aqeaus solution of formaldehyde and 2 parts of ammonium hydroxide for 60 minutes at 1500C. Ratio of SBR/CNSL formaldehyde in tyre carcass compunds were 50/0, 40/10, 30/20, 20/30, 10/40 and 50/0, respectively. The results show that substitution CNSL – formaldehyde resin for SBR was up to 10 phr. Increasing amount of CNSL-formaldehyde resins have increase physical properties such as hardness, peel test, and density, but decreased tensile strength,elongation at break, and abrasion resistance. A compound with ratio SBR/CNSL-formaldehyde resin 40/10 performed the best physical properties i.e:139.454 kg/cm2 tensile strength, 710.97% elongation at break, 62 Shore A hardness, 1.124 g/cm3density, 423.477 N/inchi peel test, and 3.214 mm3/kgm abrasion resistance, respectively

  4. Enhancing graphene oxide reinforcing potential in composites by combined latex compounding and spray drying

    Science.gov (United States)

    Mao, Yingyan; Zhang, Shubai; Zhang, Dandan; Chan, Tung W.; Liu, Li

    2014-04-01

    A new strategy was developed to prepare graphene oxide/styrene-butadiene rubber (GO/SBR) composites with highly exfoliated GO sheets and strong interfaces. In particular, GO/SBR microparticles, in which exfoliated GO sheets (with a thickness of ˜1 nm and diameter of tens of nanometers) are trapped in a well-dispersed state throughout the SBR matrix, were made by a combined latex-compounding and spray-drying method. Subsequently, a chemical bridge between GO and rubber matrix through KH550 and Si69 was built during vulcanization, and the interfacial strength of the cured GO/SBR composite was remarkably improved. Due to the highly exfoliated structure and the strong interface, the GO/SBR composite exhibited 7.8 times higher modulus at 300% strain and 6.4 times higher tensile strength compared with cured pure SBR. The combined latex-compounding and spray-drying method presented here is feasible and water-mediated and has great potential for industrial applications.

  5. Prediction of heat generation in rubber or rubber-metal springs

    Directory of Open Access Journals (Sweden)

    Banić Milan S.

    2012-01-01

    Full Text Available The temperature of rubber or rubber-metal springs increases under cyclic loading, due to hysteresis losses and low rubber thermal conductivity. Hysteresis losses correspond to energy dissipation from the rubber, which is primarily converted into heat. This well-known phenomenon, called heat build-up, is the primary reason for rubber aging. Increase in temperature within the rubber compound leads to degradation of its physical and chemical properties, increase in stiffness and loss of damping capability. This paper presents a novel procedure of heat generation prediction in rubber or rubber-metal springs. The procedure encompasses the prediction of hysteresis loss, i. e. dissipated energy within the rubber, by finite element analysis and application of a modern visco-plastic rubber constitutive model. The obtained dissipated energy was used as an input for transient thermal analysis. Verification of the proposed procedure was performed by comparison of simulation results with experimentally obtained data during the dynamic loading of the rubber specimen. The proposed procedure is highly computationally efficient and it enables time integration, which can be problematic in coupled mechanical thermal analysis. [Projekat Ministarstva nauke Republike Srbije, br. TR35005: Research and Development of New Generation of Wind Turbines of High Energy Efficiency

  6. Effect of Recycled Rubber Particles and Silica on Tensile and Tear Properties of Natural Rubber Composites

    Directory of Open Access Journals (Sweden)

    Velu CHANDRAN

    2016-05-01

    Full Text Available Application of scrap rubber and worn out tires in natural rubber compounds has been studied. The scrap rubber can, however, be recycled and compounded with natural rubber and thus can be generated as a rubber composite. In this work, recycled rubber particles (RRP were prepared using pulverization process. Then, RRP was blended with natural rubber and silica compounds, and it was synthesized by two- roll mill and hydraulic press at specified operating conditions. The samples ranging from 0 to 40 phr of RRP loaded with silica were used as constant filler. The mechanical properties and morphological analysis were carried out. The results showed that tensile strength and elongation at break gradually decreased with increasing RRP loading in natural rubber and silica compounds. Tensile modulus went down at 10 phr of RRP and then showed an increasing trend. Hardness increased up to 30 phr of RRP and tear strength increased up to 20 phr of RRP. A comparative study was also carried out with virgin natural rubber vulcanizates. The incorporation of RRP and silica up to 20 phr in natural rubber did not lower the performance of rubber articles. Morphological studies revealed that better filler dispersion, interfacial adhesion, and cross link density could increase the tensile and tear strengths.DOI: http://dx.doi.org/10.5755/j01.ms.22.2.7330

  7. Unraveling the Mystery of Natural Rubber Biosynthesis

    Science.gov (United States)

    Natural rubber (NR) is primarily obtained from Hevea brasiliensis, commonly known as the Brazilian rubber tree. As this species contains little genetic variation, it is susceptible to pathogen-based eradication. Consequently, it is imperative that a biomimetic pathway for NR production be developed....

  8. Biorefinery of proteins from rubber plantation residues

    NARCIS (Netherlands)

    Widyarani, R.

    2016-01-01

    Biorefinery of rubber tree side streams could add economic value and income for farmers, who already grow the trees for latex production. The objective of this research was to design a process for the recovery of proteinaceous fractions from rubber tree. The aimed applications were expected to be

  9. Roughness Perception during the Rubber Hand Illusion

    Science.gov (United States)

    Schutz-Bosbach, Simone; Tausche, Peggy; Weiss, Carmen

    2009-01-01

    Watching a rubber hand being stroked by a paintbrush while feeling identical stroking of one's own occluded hand can create a compelling illusion that the seen hand becomes part of one's own body. It has been suggested that this so-called rubber hand illusion (RHI) does not simply reflect a bottom-up multisensory integration process but that the…

  10. Amino acid modifiers in guayule rubber compounds

    Science.gov (United States)

    Tire producers are increasingly interested in biobased materials, including rubber but also as compounding chemicals. An alternative natural rubber for tire use is produced by guayule, a woody desert shrub native to North America. Alternative compounding chemicals include naturally-occurring amino a...

  11. EVALUATION OF THE ADSORPTION POTENTIAL OF RUBBER ...

    African Journals Online (AJOL)

    2012-11-03

    Nov 3, 2012 ... Abstract. The objective of this study was to produce activated carbon from rubber seed pericarp and to evaluate its performance with commercial activated carbon in the treatment of abattoir wastewater as well as its potential in the adsorption of iron (III) ions from aqueous solution. The rubber seed pericarp ...

  12. RADIATION INDUCED VULCANIZATION OF RUBBER LATEX

    Science.gov (United States)

    Mesrobian, R.B.; Ballantine, D.S.; Metz, D.J.

    1964-04-28

    A method of vulcanizing rubber latex by exposing a mixture containing rubber latex and from about 15 to about 21.3 wt% of 2,5-dichlorostyrene to about 1.1 megarads of gamma radiation while maintaining the temperature of the mixture at a temperature ranging between from about 56 to about 59 deg C is described. (AEC)

  13. Patients' attitudes to rubber dam.

    Science.gov (United States)

    Stewardson, D A; McHugh, E S

    2002-10-01

    The aims of this study were to record patients' views of their experience of RD use in an objective manner, and to evaluate the influence of some personal and clinical factors on patients' opinion. A questionnaire was designed which was then distributed to patients receiving dental treatment under RD by (a) final-year dental students at Birmingham Dental School, and (b) general dental practitioners. Patients completed the confidential questionnaire anonymously after treatment, outside the treatment room. After 100 correctly completed forms were collected from group (a) and 106 from group (b), data were entered into a database and subsequently analyzed using SPSS. Analyses were confined to simple cross-tabulations of the patients' responses and potential associated factors, with chi-square analysis and appropriate follow-up comparisons wherever necessary. In both groups, the majority of patients said they would prefer RD to be used at their next appointment, and most had a positive opinion of the experience. No statistically significant association between age, sex, procedure, application time or duration of use and preference for rubber dam was found. Prolonged RD use showed some association with a negative opinion of the experience of RD. Compared with the dentists, students took longer to apply rubber dam and it was in place for longer. Fewer student patients preferred RD next time, and were less positive about its use than the dentists' patients. Further evidence is presented that (i) Patients generally are not averse to RD. (ii) Placement of rubber dam does not take long. (iii) Operator experience improves patient compliance.

  14. Photoinduced orientation in natural rubber

    Science.gov (United States)

    de Souza, Nara C.; Cavalheri, Adriana S.; Brito, Jackeline B.; Job, Aldo E.; Oliveira, Osvaldo N.; Giacometti, José A.; Silva, Josmary R.

    2012-04-01

    Azobenzene molecules and their derivatives have been widely investigated for their potential applications in optical and electrooptical devices. We have prepared a new guest-host system from natural rubber (NR) impregnated with azobenzene derivative Sudan Red B (SRB). The effects of stretching and immersion time on photoinduced orientation were investigated by birefringence signal measurements. We have found that the molecular orientation increase when the samples are stretched and decrease with the increase of immersion time. The first behavior was explained by using the random coil model and the latter was attributed to increase of the aggregation of SRB into NR matrix.

  15. Coal Producer's Rubber Waste Processing Development

    Science.gov (United States)

    Makarevich, Evgeniya; Papin, Andrey; Nevedrov, Alexander; Cherkasova, Tatyana; Ignatova, Alla

    2017-11-01

    A large amount of rubber-containing waste, the bulk of which are worn automobile tires and conveyor belts, is produced at coal mining and coal processing enterprises using automobile tires, conveyor belts, etc. The volume of waste generated increases every year and reaches enormous proportions. The methods for processing rubber waste can be divided into three categories: grinding, pyrolysis (high and low temperature), and decomposition by means of chemical solvents. One of the known techniques of processing the worn-out tires is their regeneration, aimed at producing the new rubber substitute used in the production of rubber goods. However, the number of worn tires used for the production of regenerate does not exceed 20% of their total quantity. The new method for processing rubber waste through the pyrolysis process is considered in this article. Experimental data on the upgrading of the carbon residue of pyrolysis by the methods of heavy media separation, magnetic and vibroseparation, and thermal processing are presented.

  16. Occupational exposure to rubber vulcanization products during repair of rubber conveyor belts in a brown coal mine.

    Science.gov (United States)

    Gromiec, Jan P; Wesołowski, Wiktor; Brzeźnicki, Sławomir; Wróblewska-Jakubowska, Krystyna; Kucharska, Małgorzata

    2002-12-01

    Several hundred chemical compounds were found in workroom environments in the rubber industry, but most of the published exposure data relate to the production of tyres; information from the "non-tyre" sections are very limited, if any. This study was carried out to identify chemical substances and measure their air concentrations in the repair shop of a brown coal mine in which damaged rubber conveyor belts were repaired. GC-MS and HPLC analysis of stationary air samples resulted in identification of aliphatic and aromatic hydrocarbons to C12, PAHs, alcohols, phenols, ketones, heterocyclic nitrogen and sulfur compounds. Quantitative evaluation of occupational exposure included determination of organic compound vapours collected on charcoal (GC-MSD), polycyclic aromatic hydrocarbons (HPLC), N-nitrosoamines and other amines (GC-NPD) and DNPH derivatives of aldehydes (HPLC) in the breathing zone of workers representing all job titles. The concentrations of investigated compounds were very low. Carcinogenic substances: N-nitrosoamines, benzene, PAHs were not present in workroom air in concentrations exceeding limits of detection of the analytical methods being applied; concentrations of methylisobutylketone, tetrachloroethylene, naphtha, aromatic hydrocarbons, phthalates and aldehydes were much lower than the respective occupational exposure limit values. The results indicate much lower exposure than that reported in the production of tyres and other fabricated rubber products.

  17. Science and technology of rubber reclamation with special attention to NR based waste latex products

    NARCIS (Netherlands)

    Rajan, V.V.; Dierkes, Wilma K.; Joseph, R.; Noordermeer, Jacobus W.M.

    2006-01-01

    A comprehensive overview of reclamation of cured rubber with special emphasis on latex reclamation is depicted in this paper. The latex industry has expanded over the years to meet the world demands for gloves, condoms, latex thread, etc. Due to the strict specifications for the products and the

  18. Natural rubber latex: determination and interpretation of flow curves

    Directory of Open Access Journals (Sweden)

    Harrison Lourenço Corrêa

    2015-08-01

    Full Text Available AbstractAs consumers become more demanding, the importance grows of guaranteeing the quality of products. The employment of reliable testing techniques that assure the origin and characteristics of the inputs used by industry is a key factor in this respect. In the rubber processing industry, the most commonly used characterization tests include determination of the total solids and dry rubber content, mechanical stability, odor, color and presence of volatile compounds, among others. For the most part, these tests are sufficient for the latex transformation industry. However, in situations where there is a need to know the behavior of latex in reaction to the mechanical forces of machines (mixers, pumps, etc., other tests must be used. Rheological tests to determine viscoelastic data by means of plotting flow curves combined with the application of theoretical models can provide important details for characterization of different types of latex. This article presents the protocol employed by the Rheology and Image Laboratory of Rio de Janeiro State University (UERJ for the rheological study of Brazilian latex. The samples analyzed came from the state of São Paulo.

  19. The Effect of Rubber Mixing Process on The Curing Characteristics of Natural Rubber

    Directory of Open Access Journals (Sweden)

    Abu Hasan

    2013-04-01

    Full Text Available This research is aimed at studying the relationship between rubber mixing processes and curing characteristics of natural rubber. The curing characteristic analysis was carried out through a natural rubber formula having been masticated and mixed, followed by curing. As many as four mastication methods were finely applied; each respected four sequences of rubber mixing process. In the first method, rubber was masticated for 5 minutes and then rubber chemicals and carbon black N 330 were  simultaneously added. In the second and the third methods, rubber was masticated for 1 minute and then carbon blacks and rubber chemicals were also simultaneously added but using different type of fillers. In the fourth method, rubber was masticated for 3 minutes and then rubber chemicals and carbon black were subsequently added. The additions of rubber chemicals and carbon blacks to the masticated rubber were distinguished by the sequence and time allocated for each mixing process. The carbon blacks were added in two stages by which 10 phr was added first and the remaining 40 phr was added later along with oil. In another method, ratios of the carbon blacks addition (as done in the first  and the second stages were 20:30, 30:20, and 40:10. The examination results showed that rubber mixing process gave an impact on the changes of curing characteristics. They were much affected by the method of carbon black addition. The mixing temperature also had an effect on both curing time and curing rate in which the higher the mixing temperature, the lower the curing time and curing rate. Vulcanization temperature also affected the curing time and curing rate in which the higher the vulcanization temperature, the lower the curing time and the higher the curing rate. Lastly, particle size of carbon black also gave an impact on the curing time and curing rate in which the smaller the particle size, the lower the curing time and the higher the curing rate.

  20. Principais copolímeros elastoméricos à base de butadieno utilizados na indústria automobilística The most important butadiene based elastomers employed in the automotive industry

    Directory of Open Access Journals (Sweden)

    Tereza C. J. Rocha

    2007-12-01

    Full Text Available Copolímeros elastoméricos à base de butadieno são amplamente utilizados na indústria automobilística. Dentre esses destacam-se os copolímeros de butadieno-estireno (SBR e butadieno-acrilonitrila (NBR. O SBR apresenta maior importância comercial, devido a sua aplicação na produção de pneus. Quando SBR é utilizado juntamente com o homopolímero de butadieno BR-alto cis, excelentes propriedades são obtidas para sua aplicação na banda de rodagem de pneus. O copolímero elastomérico NBR é empregado em artefatos em que é necessária boa resistência a solventes orgânicos e a óleos. Nos últimos anos, as empresas automobilísticas e produtoras de pneumáticos vêm se preocupando com o meio-ambiente e, conseqüentemente, têm investido em novos processos de síntese, mais limpos, para a produção desses elastômeros. Assim, o objetivo deste artigo é apresentar uma revisão sobre dois importantes copolímeros elastoméricos à base de butadieno, SBR e NBR, abordando os processos de síntese, características principais, processamento e aplicações.Elastomer copolymers based on butadiene are widely applied in the automotive industry. Among those copolymers the most important ones are styrene-butadiene (SBR and nitrile-butadiene (NBR. SBR presents higher commercial interest, due to its application in the tire production. When SBR is mixed with high cis-1,4 polybutadiene, excellent properties are attained for application on the pneumatics treads. NBR can be used in a wide variety of application areas requiring oil, fuel, and chemical resistance. In the last years, the automotive and pneumatic industries have been increasingly concerned with environmental issues, and have invested in synthesis processes for elastomers that are less aggressive to the environment. Thus, the purpose of this article is to present a review on two important butadiene elastomer copolymers, SBR and NBR, with emphasis on the polymerization processes. The main

  1. Minimum Variance Estimation of Yield Parameters of Rubber Tree ...

    African Journals Online (AJOL)

    Although growth and yield data are available in rubber plantations in Nigeria for aggregate rubber production planning, existing models poorly estimate the yield per rubber tree for the incoming year. Kalman lter, a exible statistical estimator, is used to combine the inexact prediction of the rubber production with an equally ...

  2. 30 CFR 77.606-1 - Rubber gloves; minimum requirements.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Rubber gloves; minimum requirements. 77.606-1... COAL MINES Trailing Cables § 77.606-1 Rubber gloves; minimum requirements. (a) Rubber gloves (lineman's... be used and tested in accordance with the provisions of §§ 77.704-6 through 77.704-8. (b) Rubber...

  3. Butterfly valve of all rubber lining type

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, Shosaku; Nakatsuma, Sumiya (Kubota Ltd., Osaka (Japan)); Sasaki, Iwao; Aoki, Naoshi

    1982-08-01

    The valves used for the circulating water pipes for condensers in nuclear and thermal power stations have become large with the increase of power output, and their specifications have become strict. The materials for the valves change from cast iron to steel plate construction. To cope with sea water corrosion, rubber lining has been applied to the internal surfaces of valve boxes, and the build-up welding of stainless steel has been made on the edges of valves. However, recently it is desired to develop butterfly valves, of which the whole valve disks are lined with hard rubber. For the purpose of confirming the performance of large bore valves, a 2600 mm bore butterfly valve of all rubber lining type was used, and the opening and closing test of 1100 times was carried out by applying thermal cycle and pressure difference and using artifical sea water. Also the bending test of hard rubber lining was performed with test pieces. Thus, it was confirmed that the butterfly valves of all rubber lining type have the performance exceeding that of the valves with build-up welding. The course of development of the valves of all rubber lining type, the construction and the items of confirmation by tests of these valves, and the tests of the valve and the hard rubber lining described above are reported.

  4. Effect of Rubberized Bitumen Blending Methods on Permanent Deformation of SMA Rubberized Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Herda Yati Katman

    2016-01-01

    Full Text Available This study aims at comparing the permanent deformation of Stone Mastic Asphalt (SMA rubberized asphalt mixtures produced by the wet process. In this study, rubberized binders were prepared using two different blending methods, namely, continuous blend and terminal blend. To study the creep behaviour of control and rubberized asphalt mixtures, the dynamic creep test was performed using Universal Materials Testing Apparatus (UMATTA at different temperatures and stress levels. Zhou three-stage creep model was utilized to evaluate the deformation characteristics of the mixtures. In all test conditions, the highest resistance to permanent deformation is showed by the rubberized mixtures produced with continuous blend binders. This study also reveals that the permanent deformation of rubberized mixtures cannot be predicted based on the characteristics of the rubberized binders.

  5. Structural characterization of rubber from jackfruit and euphorbia as a model of natural rubber.

    Science.gov (United States)

    Mekkriengkrai, Dararat; Ute, Koiichi; Swiezewska, Ewa; Chojnacki, Tadeusz; Tanaka, Yasuyuki; Sakdapipanich, Jitladda T

    2004-01-01

    A structural study of low molecular weight rubbers from Jackfruit (Artocarpus heterophyllus) and Painted spurge (Euphorbia heterophylla) was carried out as model compounds of natural rubber from Hevea brasiliensis. The rubber content of latex from Jackfruit was 0.4-0.7%, which is very low compared with that of 30-35% in the latex from Hevea tree. The rubber from Jackfruit latex was low molecular weight with narrow unimodal molecular weight distribution (MWD), whereas that obtained from E. heterophylla showed very broad MWD. The 1H and 13C NMR analyses showed that Jackfruit rubber consists of a dimethylallyl group and two trans-isoprene units connected to a long sequence of cis-isoprene units. The alpha-terminal group of Jackfruit rubber was presumed to be composed of a phosphate group based on the presence of 1H NMR signal at 4.08 ppm corresponding to the terminal =CH-CH2OP group.

  6. SUPPLY-CHAIN OF NATURAL RUBBER IN INDONESIA

    OpenAIRE

    Bustanul Arifin

    2011-01-01

    The study examines the supply chain of natural rubber production in Indonesia and assessing the transmission of prices to rubber growers and provides recommendations for a suitable scheme that would help to ensure high production standards and a sustainable return for natural rubber production.  The frameworks to examine the performance of supply chain of rubber marketing rely mostly on the efficiency level of marketing system of natural rubbers, including the value chain principles in marke...

  7. Analysis of rubber supply in Sri Lanka

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, M.J.; Nerlove, M.; Peters, R.K. Jr.

    1987-11-01

    An analysis of the supply response for perennial crops is undertaken for rubber in Sir Lanka, focusing on the uprooting-replanting decision and disaggregating the typical reduced-form supply response equation into several structural relationships. This approach is compared and contrasted with Dowling's analysis of supply response for rubber in Thailand, which is based upon a sophisticated reduced-form supply function developed by Wickens and Greenfield for Brazilian coffee. Because the uprooting-replanting decision is central to understanding rubber supply response in Sri Lanka and for other perennial crops where replanting activities dominate new planting, the standard approaches do not adequately capture supply response.

  8. Devolatilization and Combustion of Tire Rubber and Pine Wood in a Pilot Scale Rotary Kiln

    DEFF Research Database (Denmark)

    Nielsen, Anders R.; Larsen, Morten B.; Glarborg, Peter

    2012-01-01

    of industrial waste. In this study, devolatilization and combustion of large particles of tire rubber and pine wood with equivalent diameters of 10 mm to 26 mm are investigated in a pilot scale rotary kiln able to simulate the process conditions present in the material inlet end of cement rotary kilns....... Investigated temperatures varied from 700 to 1000 °C, and oxygen concentrations varied from 5% v/v O2 to 21% v/v O2. The devolatilization time of tire rubber and pine wood were found to mainly depend on temperature and particle size and were within 40 to 170 s. Rate limiting parameters for char oxidation...... of tire rubber and pine wood were found to be bulk oxygen concentration, mass transfer rate of oxygen, raw material fill degree, raw material characteristics, and temperature. Kiln rotational speed only had a minor effect on the char oxidation when the raw material bed was in a rolling motion. Initial...

  9. Innovative Application of Biopolymer Keratin as a Filler of Synthetic Acrylonitrile-Butadiene Rubber NBR

    Directory of Open Access Journals (Sweden)

    Mirosława Prochoń

    2013-01-01

    Full Text Available The current investigations show the influence of keratin, recovered from the tanning industry, on the thermal and mechanical properties of vulcanizates with synthetic rubber acrylonitrile-butadiene rubber NBR. The addition of waste protein to NBR vulcanizates influences the improvement of resistance at high temperatures and mechanical properties like tensile strength and hardness. The introduction of keratin to the mixes of rubber previously blended with zinc oxide (ZnO before vulcanization process leads to an increase in the cross-linking density of vulcanizates. The polymer materials received including addition of proteins will undergo biodecomposition in natural conditions. After soil test, vulcanizates with keratin especially keratin with ZnO showed much more changes on the surface area than vulcanizates without protein. In that aerobic environment, microorganisms, bacteria, and fungus digested better polymer materials containing natural additives.

  10. Promoting the use of crumb rubber concrete in developing countries.

    Science.gov (United States)

    Batayneh, Malek K; Marie, Iqbal; Asi, Ibrahim

    2008-11-01

    The use of accumulated waste materials in third world countries is still in its early phases. It will take courage for contractors and others in the construction industry to recycle selected types of waste materials in the concrete mixes. This paper addresses the recycling of rubber tires accumulated every year in Jordan to be used in concrete mixes. The main objectives of this research were to provide more scientific evidence to support the use of legislation or incentive-based schemes to promote the reuse of accumulated waste tires. This research focused on using crumb tires as a replacement for a percentage of the local fine aggregates used in the concrete mixes in Jordan. Different concrete specimens were prepared and tested in terms of uniaxial compression and splitting tension. The main variable in the mixture was the volumetric percentage of crumb tires used in the mix. The test results showed that even though the compressive strength is reduced when using the crumb tires, it can meet the strength requirements of light weight concrete. In addition, test results and observations indicated that the addition of crumb rubber to the mix has a limited effect toward reducing the workability of the mixtures. The mechanical test results demonstrated that the tested specimens of the crumb rubber concrete remained relatively intact after failure compared to the conventional concrete specimens. It is also concluded that modified concrete would contribute to the disposal of the non-decaying scrap tires, since the amount being accumulated in third world countries is creating a challenge for proper disposal. Thus, obliging authorities to invest in facilitating the use of waste tires in concrete, a fundamental material to the booming construction industry in theses countries, serves two purposes.

  11. Regarding the influence of the particle size of crumb rubber from waste rubber on the physical and mechanical characteristics of reclaimed rubber

    Directory of Open Access Journals (Sweden)

    Dobrotă Dan

    2017-01-01

    Full Text Available Thus, at present, a large amount of rubber waste cannot be higher harnessed due to recovery technologies used. Also, the requirements for new products of rubber worldwide are greater than the production capacity and the availability of raw materials. To offset this balance is necessary to improve technologies for recycling waste rubber so to can get regenerated rubber with the best mechanical physical characteristics. The main technology for obtaining the regenerated rubber is based on the rubber waste shredding and making the powder, so that it can be carried out de-vulcanization in autoclave. All the time it was monitored as the de-vulcanization process to be as economical and less polluting, and this requires that the sizes of the crumb rubber to be optimal. Thus, in the conducted researches was aimed to establish the particle size of crumb rubber from waste rubber so as to obtain an economical de-vulcanization, but also a reclaimed rubber with superior physical and mechanical characteristics. The organization of researches was made so that crumb of rubber waste was divided into 5 groups, bowing from crumb rubber with particle’s size of 1000 μm (RPS1, and reaching up to crumb rubber with particle’s size of 200 μm (RPS 5.

  12. Identification and subcellular localization analysis of two rubber elongation factor isoforms on Hevea brasiliensis rubber particles.

    Science.gov (United States)

    Dai, Longjun; Nie, Zhiyi; Kang, Guijuan; Li, Yu; Zeng, Rizhong

    2017-02-01

    Rubber elongation factor (REF) is the most abundant protein found on the rubber particles or latex from Hevea brasiliensis (the Para rubber tree) and is considered to play important roles in natural rubber (cis-polyisoprene) biosynthesis. 16 BAC (benzyldimethyl-n-hexadecylammonium chloride)/SDS-PAGE separations and mass spectrometric identification had revealed that two REF isoforms shared similar amino acid sequences and common C-terminal sequences. In this study, the gene sequences encoding these two REF isoforms (one is 23.6 kDa in size with 222 amino acid residues and the other is 27.3 kDa in size with 258 amino acid residues) were obtained. Their proteins were relatively enriched by sequential extraction of the rubber particle proteins and separated by 16 BAC/SDS-PAGE. The localization of these isoforms on the surfaces of rubber particles was further verified by western blotting and immunogold electron microscopy, which demonstrated that these two REF isoforms are mainly located on the surfaces of larger rubber particles and that they bind more tightly to rubber particles than the most abundant REF and SRPP (small rubber particle protein). Copyright © 2016. Published by Elsevier Masson SAS.

  13. Evaluation of thermal insulation and mechanical properties of waste rubber/natural rubber composite

    Directory of Open Access Journals (Sweden)

    M.M. Abdel Kader

    2012-04-01

    Full Text Available The influences of waste rubber loading on mechanical and thermal conductivity properties were investigated for NR composite. An experimental investigation was carried out to obtain low cost construction material with desirable mechanical and thermal insulation properties. Natural rubber was loaded with different concentrations of waste rubber (200, 400, 600, 800, and 1000 phr. The addition of waste rubber leads to a slight increase in thermal conductivity values of composites but it still lies around range of thermal insulating materials. Also addition of waste rubber leads to improvement of mechanical properties of composites. The crosslink density of NR composite increases with the increase of waste rubber loading until 600 phr and after that it decreases due to the stronger the rubber–filler interaction. This leads to the decrease of the swelling index that has the opposite trend of crosslink density. So, the sample with 600 phr waste rubber is considered the optimum concentration from the swelling measurement. Filler loading results in pronounced increase in the tensile modulus and decease in the elongation at fracture which reflects the reinforcement effect of the filler. The yield stress increases with waste rubber loading increment. This delays the permanent disruption of matrix morphology. So, the optimum concentration which is 600 phr waste rubber loading agrees with the swelling and mechanical measurements which has desirable thermal insulation and high mechanical properties and decreases the cost of materials to 82% of the NR cost.

  14. Characterization of rubber particles and rubber chain elongation in Taraxacum koksaghyz

    Directory of Open Access Journals (Sweden)

    Prüfer Dirk

    2010-02-01

    Full Text Available Abstract Background Natural rubber is a biopolymer with exceptional qualities that cannot be completely replaced using synthetic alternatives. Although several key enzymes in the rubber biosynthetic pathway have been isolated, mainly from plants such as Hevea brasiliensis, Ficus spec. and the desert shrub Parthenium argentatum, there have been no in planta functional studies, e.g. by RNA interference, due to the absence of efficient and reproducible protocols for genetic engineering. In contrast, the Russian dandelion Taraxacum koksaghyz, which has long been considered as a potential alternative source of low-cost natural rubber, has a rapid life cycle and can be genetically transformed using a simple and reliable procedure. However, there is very little molecular data available for either the rubber polymer itself or its biosynthesis in T. koksaghyz. Results We established a method for the purification of rubber particles - the active sites of rubber biosynthesis - from T. koksaghyz latex. Photon correlation spectroscopy and transmission electron microscopy revealed an average particle size of 320 nm, and 13C nuclear magnetic resonance (NMR spectroscopy confirmed that isolated rubber particles contain poly(cis-1,4-isoprene with a purity >95%. Size exclusion chromatography indicated that the weight average molecular mass (w of T. koksaghyz natural rubber is 4,000-5,000 kDa. Rubber particles showed rubber transferase activity of 0.2 pmol min-1 mg-1. Ex vivo rubber biosynthesis experiments resulted in a skewed unimodal distribution of [1-14C]isopentenyl pyrophosphate (IPP incorporation at a w of 2,500 kDa. Characterization of recently isolated cis-prenyltransferases (CPTs from T. koksaghyz revealed that these enzymes are associated with rubber particles and are able to produce long-chain polyprenols in yeast. Conclusions T. koksaghyz rubber particles are similar to those described for H. brasiliensis. They contain very pure, high molecular mass

  15. Development of rubber-enriched dandelion varieties by metabolic engineering of the inulin pathway.

    Science.gov (United States)

    Stolze, Anna; Wanke, Alan; van Deenen, Nicole; Geyer, Roland; Prüfer, Dirk; Schulze Gronover, Christian

    2017-06-01

    Natural rubber (NR) is an important raw material for a large number of industrial products. The primary source of NR is the rubber tree Hevea brasiliensis, but increased worldwide demand means that alternative sustainable sources are urgently required. The Russian dandelion (Taraxacum koksaghyz Rodin) is such an alternative because large amounts of NR are produced in its root system. However, rubber biosynthesis must be improved to develop T. koksaghyz into a commercially feasible crop. In addition to NR, T. koksaghyz also produces large amounts of the reserve carbohydrate inulin, which is stored in parenchymal root cell vacuoles near the phloem, adjacent to apoplastically separated laticifers. In contrast to NR, which accumulates throughout the year even during dormancy, inulin is synthesized during the summer and is degraded from the autumn onwards when root tissues undergo a sink-to-source transition. We carried out a comprehensive analysis of inulin and NR metabolism in T. koksaghyz and its close relative T. brevicorniculatum and functionally characterized the key enzyme fructan 1-exohydrolase (1-FEH), which catalyses the degradation of inulin to fructose and sucrose. The constitutive overexpression of Tk1-FEH almost doubled the rubber content in the roots of two dandelion species without any trade-offs in terms of plant fitness. To our knowledge, this is the first study showing that energy supplied by the reserve carbohydrate inulin can be used to promote the synthesis of NR in dandelions, providing a basis for the breeding of rubber-enriched varieties for industrial rubber production. © 2016 The Authors. Plant Biotechnology Journal published by Society for Experimental Biology and The Association of Applied Biologists and John Wiley & Sons Ltd.

  16. Exposure to rubber process dust and fume since 1970s in the United Kingdom; influence of origin of measurement data.

    Science.gov (United States)

    Agostini, Michela; de Vocht, Frank; van Tongeren, Martie; Cherrie, John W; Galea, Karen S; Kromhout, Hans

    2010-05-01

    The objective of this study was to compare measured concentrations of rubber process dust and rubber fume originating from different sources in the British rubber manufacturing industry. Almost 8000 exposure measurements were obtained from industry-based survey results collected by the British Rubber Manufacturers' Association (BRMA), and covering the years 1977 to 2002, and from a series of small surveys contained in the Health and Safety Executive's (HSE) National Exposure Database (HSE-NEDB) from 1980 to 2002. The analysis investigated temporal trends in the exposure concentrations and the underlying main factors responsible for these changes. Analyses were carried out using hierarchical linear mixed effects models. Average personal exposures to rubber process dust and rubber fumes were respectively a factor 2 and 4 higher for the HSE-NEDB data when compared to data originating from the industry (BRMA data). Personal exposure to rubber process dust decreased on average by 4.1% (95% CI 4.7-3.6) annually for the BRMA data and slightly less at 2.3% (95% CI 5.2-0.7%) per annum for the HSE-NEDB data. Personal exposure to rubber fume also showed a downward temporal trend of 2.9% (95% CI 3.6-2.3%) and 4.8% (95% CI 7.4-2.1%) annually for the BRMA and HSE-NEDB data, respectively. These trends differed considerably between departments. No major changes in the estimated temporal trends in exposure concentrations were observed after including the presence of local exhaust ventilation in the models for any department in the BRMA and HSE-NEDB datasets. Lack of information on the quality and status of the local exhaust ventilation is the most likely explanation for this. In conclusion, even though there were relatively similar downward time trends in both rubber process dust and fume concentrations in both datasets, the source of exposure data was an important determinant of average exposure concentrations present in the British rubber manufacturing industry. Lack of detailed

  17. Visual evoked potentials in rubber factory workers.

    Science.gov (United States)

    Tandon, O P; Kumar, V

    1997-01-01

    Pattern reversal visual evoked potentials (pVEP) were studied in 39 male rubber factory workers in the age range of 18-55 years and 20 control subjects (aged 18-46 years) not exposed to the rubber factory environment. Results revealed that 20 (51%) rubber factory workers had abnormal latencies of wave P1 (dominant component of pVEP) as per accepted criteria of 99% tolerance limit set for the control group (i.e. any value above mean +3 SD of control was considered abnormal). The section-wise per cent distribution of abnormalities was vulcanization (83%), tubing (75%), calendering (60%), loading (38%) and mixing (14%). This study provides electrophysiological evidence that rubber factory environments affect the conduction processes in optical pathways from their origin in the retina to striate cortex. However, this study has its limitations in not identifying the specific chemical(s) causing these changes in VEP.

  18. Oils and rubber from arid land plants

    Science.gov (United States)

    Johnson, J. D.; Hinman, C. W.

    1980-05-01

    In this article the economic development potentials of Cucurbita species (buffalo gourd and others), Simmondsia chinensis (jojoba), Euphorbia lathyris (gopher plant), and Parthenium argentatum (guayule) are discussed. All of these plants may become important sources of oils or rubber.

  19. Contact allergy to rubber accelerators remains prevalent

    DEFF Research Database (Denmark)

    Schwensen, J F; Menné, T; Johansen, J D

    2016-01-01

    several clinical cases with allergic facial dermatitis to rubber. OBJECTIVES: To evaluate temporal trends of contact allergy to rubber accelerators from the European baseline series in a tertiary patch test clinic in Denmark, and examine associations with anatomical locations of dermatitis. METHODS: Patch...... test and clinical data collected in a Danish tertiary dermatology clinic in Gentofte, Herlev, Copenhagen between 1 January 2005 and 31 December 2014 were analysed. The following rubber accelerators or mixtures in petrolatum from the European baseline patch test series were included: thiuram mix 1.......0%, mercaptobenzothiazole 2.0% and mercapto mix 1.0%. RESULTS: The overall prevalence of contact allergy to rubber accelerators was 3.1% with no significant change during the study period (Ptrend = 0.667). Contact allergy to thiuram mix was the most prevalent and was significantly associated with occupational contact...

  20. Plastics and Rubber Products Manufacturing (NAICS 326)

    Science.gov (United States)

    Find environmental regulatory and compliance information for plastics and rubber products manufacturing (which includes the manufacture of cellulose and other fibers) including information about NESHAPs and effluent guidelines for wastewater discharges

  1. Kurumsal Sosyal Sorumluluk Kapsamında Çevre Açıklamaları İle Firma Özellikleri Arasındaki İlişki: Kimya, Petrol, Kauçuk ve Plastik Ürünler Sektöründe Bir Uygulama - Relation Between Company Features And Environmental Statement Within Corporate Social Responsibility: An Application In Chemistry, Petroleum, Rubber And Plastics Products Industry

    Directory of Open Access Journals (Sweden)

    Şule YILDIZ

    2016-06-01

    Full Text Available The purpose of this research is to determine the relation between company features and environmental statement amounts in the annual activity reports of companies. To this end, activity reports of 19 companies making business in chemistry, petroleum, rubber and plastic products industry in Borsa Istanbul were inspected with content analysis method for 2008 - 2014. The company features inspected within the research are size, equity profitability, active profitability, debt levels, stock market listing date and date of foundation of companies. In the research, the relation between environmental statement level and related company features were analyzed with panel regression model. According to the results of research, the environmental statement level has positive relation with date of foundation and debt level and it has negative relation with size and stock market listing and it is statistically meaningful. However, no statistically meaningful relation was found between equity profitability and asset profitability and the environmental statement level.

  2. Use of waste rubber as concrete additive.

    Science.gov (United States)

    Chou, Liang Hsing; Lu, Chun-Ku; Chang, Jen-Ray; Lee, Maw Tien

    2007-02-01

    For resource reutilization, scrap tyres have long been investigated as an additive to concrete to form 'Rubcrete' for various applications and have shown promising results. However, the addition of rubber particles leads to the degradation of physical properties, particularly, the compressive strength of the concrete. In this study, a theoretical model was proposed to shed light on the mechanisms of decrease in compressive strength due to the addition of rubber particles as well as improvement in compressive strength through modification of particle surfaces. The literature suggests that the compressive strength can be improved by soaking the rubber particles in alkaline solution first to increase the inter-phase bonding between the rubber particles and cement. Instead, we discovered that the loss in compressive strength was due to local imperfections in the hydration of cement, induced by the addition of heterogeneous and hydrophobic rubber particles. Microscopic studies showed that the rubber particles disturbed the water transfer to create channels, which were prone to cracking and led to a loss in the compressive strength. Unexpectedly, no cracking was found along the surfaces of the rubber particles, indicating that the bonding strength between the rubber particles and cement phases was not the critical factor in determining the compressive strength. Therefore, a theoretical model was proposed to describe the water transfer in the Rubcrete specimens to explain the experimental data. In the model, the local water available for hydration (Q) is: Q = -A(slv)/6piv, where Q, A(slv), and v are mass flow rate (kg s(-1)), Hamaker constant (J), and dynamic viscosity (m2 s(-1)), respectively. By maximizing the quantity Q and, in turn, the Hamaker constant A(slv), the compressive strength could be improved. The Hamaker constant A(slv) for water film on rubber particle surfaces was smaller than that for the hydrated cement particles; the water transfer rate was lower in

  3. Mechanical Parameters of Rubber-Sand Mixtures for Numerical Analysis of a Road Embankment

    Science.gov (United States)

    Kowalska, Magdalena; Chmielewski, Maciej

    2017-10-01

    Waste production is one of the greatest problems of the modern world. It is inevitably related to the increase of industrialization. One of the most difficult, and growing in amounts, waste is scrap tyres. The most common method of utilization of end-of-life tyres by their incineration raises much concern in terms of air pollution. More sustainable seems to reuse the tyre derived products – rubber in particular – in civil engineering, where the interesting properties of this material may be effectively utilized. This paper presents results of direct shear strength tests on sand-rubber mixtures, which were next applied to a numerical FEM (finite element method) model of a road embankment built on soft ground. The laboratory tests, conducted for two types of scrap tyre rubber granulates (0.5 – 2 mm and 1 – 5 mm in size) mixed with medium fluvial sand in various proportions (5, 10, 30 and 50% by weight), proved that the unit weight of the mixtures is distinctly smaller that the unit weight of sand alone and at 50% rubber content it drops by half. The internal angle of friction stays almost unchanged for the mixtures with up to 10% of rubber (33 - 37°), but decreases by about 10° when the rubber content increases to 50%. In most of the cases analysed, the cohesion intercept is higher in case of sand-rubber mixtures when compared to sand alone. The numerical model simulated a 4.5 m high embankment with a 3 m thick layer made of sand-rubber mixtures, containing 0%, 10% or 30% of the waste product, founded on a weak subsoil (with a 3 m layer of organic soil). The results showed that stability factor of the structure built with the layer containing 30% of the coarser rubber granulate has increased from 1.60 – for sand only, to 2.15. The embankment was also able to carry load increased from 32 kPa to 45.5 kPa and its base showed much smaller settlement. The results prove that the use of tyre derived aggregates in embankment construction is not only an effective

  4. Why Does a Rubber Ball Bounce? The Molecular Origins of Rubber ...

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 4. Why Does a Rubber Ball Bounce? The Molecular Origins of Rubber Elasticity. V G Geethamma Sabu Thomas. General Article Volume 2 Issue 4 April 1997 pp 48-54 ...

  5. Evaluation of silanes in SBR 1502 / Telinne Monspessulana flour composites

    Directory of Open Access Journals (Sweden)

    Oscar Buitrago

    Full Text Available Abstract A comparative study was performed on the effect of the addition of silane coupling agents (SCA, vinyltrimethoxysilane (VTMS and 3-aminopropyltriethoxysilane (APTES to a mixture of styrene butadiene rubber SBR1502 with Telinne Monspessulana flour (TMF. SCA was directly added into the mixture using untreated and mercerized TMF. Also, TMF and SBR1502 mixing trials were conducted with the TMF previously mercerized and injected with each of the silanes. The rubber compounds were subjected to tensile tests in order to evaluate the coupling power of both SCA. It was found that the vinyl silane type produced the best results in the tensile strength.

  6. Estudio y análisis de los polímeros derivados del estireno-butadieno

    OpenAIRE

    Juárez Varón, David; Balart Gimeno, Rafael Antonio; Ferrándiz Bou, Santiago; García Sanoguera, David

    2013-01-01

    [EN] This article aims to study and analyze polymers derived from styrene-butadiene, known as SBR rubber, being the most widely used worldwide and having replaced almost entirely natural rubber, identifying their properties, classification, applications and possible additives [ES] El presente artículo tiene como objetivo el estudio y análisis de los polímeros derivados del estireno-butadieno, más conocidos como cauchos SBR, siendo los más utilizados a nivel mundial y habiendo s...

  7. Energy analysis of 108 industrial processes. Phase 1, industrial applications study

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, B. B.; Brown, H. L.

    1979-06-01

    Extensive data are compiled for energy balances in 108 industrial processes. Specific information on unit operation, material, temperature, unrecoverable losses, along with the process flow diagram is given for each of the industries. The following industries are included: meak packing; milk; canned fruits and vegetables; baked goods; sugar refining; soybean; textiles; wood products; building materials; alkalies and chlorine; inorganic gases; pigments, chemicals; plastic materials and resins; synthetic rubbers; organic fibers; pharmaceutical preparations; organic chemicals; petroleum products; fertilizers; rubber products; glass; blast furnaces and steel mills; metals; farm machinery; motor vehicles; and photographic materials. The SIC's for each industry are identified.

  8. Gene expression analysis and SNP/InDel discovery to investigate yield heterosis of two rubber tree F1 hybrids.

    Science.gov (United States)

    Li, Dejun; Zeng, Rizhong; Li, Yan; Zhao, Manman; Chao, Jinquan; Li, Yu; Wang, Kai; Zhu, Lihuang; Tian, Wei-Min; Liang, Chengzhi

    2016-04-25

    As an important industrial material, natural rubber is mainly harvested from the rubber tree. Rubber tree breeding is inefficient, expensive and time-consuming, whereas marker-assisted selection is a feasible method for early selection of high-yield hybrids. We thus sequenced and analyzed the transcriptomes of two parent rubber trees (RRIM 600 and PR 107) and their most productive hybrids (RY 7-33-97 and RY 7-20-59) to understand their gene expression patterns and genetic variations including single nucleotide polymorphisms (SNPs) and small insertions/deletions (InDels). We discovered >31,000 genetic variations in 112,702 assembled unigenes. Our results showed that the higher yield in F1 hybrids was positively associated with their higher genome heterozygosity, which was further confirmed by genotyping 10 SNPs in 20 other varieties. We also showed that RY 7-33-97 and RY 7-20-59 were genetically closer to RRIM 600 and PR 107, respectively, in agreement with both their phenotypic similarities and gene expression profiles. After identifying ethylene- and jasmonic acid-responsive genes at the transcription level, we compared and analyzed the genetic variations underlying rubber biosynthesis and the jasmonic acid and ethylene pathways in detail. Our results suggest that genome-wide genetic variations play a substantive role in maintaining rubber tree heterosis.

  9. Modeling of elastic-strength properties of elastomers

    Directory of Open Access Journals (Sweden)

    O. V. Karmanova

    2016-01-01

    Full Text Available Model "structure-property", which takes into account the structural heterogeneity of polymer compositions has been developed. Experimental compositions based on styrene-butadiene rubber SCS 30ARK and crosslinked, high viscosity polymer (high-molecular filler - VMN in different proportions, as well as softeners (industrial oil I-12A, oil PN-6, low-molecular polybutadiene PBN were investigated. Samples that differ significantly in viscosity were obtained. The rubber blends and vulcanizates, based on the experimental of polymer compositions, were prepared. Physico-mechanical properties - tensile strength, elongation at break, Shore A. A hardness were determined. For describe the physical and mechanical properties of polymers logarithmic additivity rule was used. The properties of the polymer composition (PС were determined by a single dominant component (resin composition consisting of a high rubber and a filler and further components (softeners. Identification algorithm consists of four steps. The implementation of this algorithm is carried out using experimental design techniques. Estimation of the unknown parameters in the equation was carried out using the method of least squares. Quality evaluation of the model was conducted with the criteria Fisher, turning points, the Durbin-Watson, R / S-criterion. It is found that the model adequately describes the change of physicomechanical properties depending on the composition of polymer compositions. 3d graphics of the physical-mechanical properties of the polymer compositions were built. This allowed us to estimate the contribution of the dominant component and optional components (including combinations thereof to change the parameters. It has been established that the introduction of rubber in total more than 50% of the components (BMH and softeners reduced conventional tensile strength and dramatically increases the relative error of model calculations. (BMH and softeners

  10. Respiratory and skin effects of exposure to wood dust from the rubber tree Hevea brasiliensis.

    Science.gov (United States)

    Sripaiboonkij, P; Phanprasit, W; Jaakkola, M S

    2009-07-01

    Potential health effects related to wood dust from the rubber tree, which produces natural rubber latex, have not been previously investigated. The main aim of this study was to investigate the relations of rubber tree dust exposure to respiratory and skin symptoms, asthma and lung function. A cross-sectional study was conducted among 103 workers (response rate 89%) in a rubber tree furniture factory and 76 office workers (73%) in four factories in Thailand. All participants answered a questionnaire and performed spirometry. Inhalable dust levels were measured in different work areas. Factory workers showed increased risk of wheezing, nasal symptoms and asthma compared to office workers. There was a dose-dependent increase in wheeze and skin symptoms in relation to dust level. Significantly increased risks of nasal symptoms (adj OR 3.67, 95% CI 1.45 to 9.28) and asthma (8.41, 1.06 to 66.60) were detected in the low exposure category. Workers exposed to ethyl cyanoacrylate glue had significantly increased risk of cough, breathlessness and nasal symptoms. There was dose-dependent reduction in spirometric lung function with wood dust level. This study provides new evidence that workers exposed to wood dust from the rubber tree experience increased risk of nasal symptoms, wheeze, asthma and skin symptoms and have reduced spirometric lung function. Exposure to cyanoacrylate is related to significantly increased respiratory symptoms. Results suggest that the furniture industry using rubber tree wood should implement appropriate exposure control measures to reduce wood dust exposure and cyanoacrylate glue exposure to protect their employees.

  11. Improving Asphalt Mixture Performance by Partially Replacing Bitumen with Waste Motor Oil and Elastomer Modifiers

    Directory of Open Access Journals (Sweden)

    Sara Fernandes

    2017-08-01

    Full Text Available The environmental concern about waste generation and the gradual decrease of oil reserves has led the way to finding new waste materials that may partially replace the bitumens used in the road paving industry. Used motor oil from vehicles is a waste product that could answer that demand, but it can also drastically reduce the viscosity, increasing the asphalt mixture’s rutting potential. Therefore, polymer modification should be used in order to avoid compromising the required performance of asphalt mixtures when higher amounts of waste motor oil are used. Thus, this study was aimed at assessing the performance of an asphalt binder/mixture obtained by replacing part of a paving grade bitumen (35/50 with 10% waste motor oil and 5% styrene-butadiene-styrene (SBS as an elastomer modifier. A comparison was also made with the results of a previous study using a blend of bio-oil from fast pyrolysis and ground tire rubber modifier as a partial substitute for usual PG64-22 bitumen. The asphalt binders were tested by means of Fourier infrared spectra and dynamic shear rheology, namely by assessing their continuous high-performance grade. Later, the water sensitivity, fatigue cracking resistance, dynamic modulus and rut resistance performance of the resulting asphalt mixtures was evaluated. It was concluded that the new binder studied in this work improves the asphalt mixture’s performance, making it an excellent solution for paving works.

  12. The surface modification of clay particles by RF plasma technique

    Science.gov (United States)

    Lee, Sang-Keol

    In this study, the surface coatings of ball clay, organoclay and exfoliated clay prepared by sol-gel process were done by RF plasma polymerization to improve the surface activity of the clay filler. Characterization of the above plasma-treated clays has been carried out by various techniques. The effects of plasma-treated clays as substitute of carbon black in styrene-butadiene rubber (SBR) and ethylene-propylene-diene monomer (EPDM) on the curing and mechanical properties were investigated. After plasma treatment, the tensile properties of organo and exfoliated clay were not unsatisfactory to that of carbon black filler system. Moreover, only 10 phr filler loading of plasma-treated organoclay in EPDM vulcanizates showed better results than 40 phr filler loading of carbon black in EPDM vulcanizates. The main objective of this study was to verify the applicability of the plasma technique for modifying clay surfaces for their use in the tire manufacturing industry. Another purpose was to reveal the advantage of the plasma technique used to obtain modified-clay and improved properties that those materials can display.

  13. STUDY OF THE EFFECT OF MIXED ALKOXIDES OXYPROPYLATED AROMATIC SECONDARY AMINES ON THE STRUCTURE OF DIENE POLYMERS

    Directory of Open Access Journals (Sweden)

    A. V. Firsova

    2014-01-01

    Full Text Available Summary. This article discusses the relationship structure of the diene and styrene-butadiene copolymers (SBR, the structure of the part of the initiating system of n-butyl lithium + modifier, which is a mixed alkoxide of an alkali and alkaline earth metals, which allows to control the microstructure of the diene polymer and its molecular weight characteristics. Alcohol derivatives selected high-boiling alcohols tetra (hydroxypropyl ethylenediamine (lapromol - 294 and tetrahydrofurfuryl alcohol (TGFS. The scheme of obtaining styrene-butadiene random copolymers (SBR with a high content (64 ± 4 % of vinyl units was developed. The process of copolymerization with sodium-calcium-lithium complex Са(С4Н9 2 • С4Н9Na • LiOR was carried out. After water decontamination residues deactivated complex remain in the polymer as a filler. Studied the copolymerization of butadiene with styrene in the presence of lithium amide, which is obtained on the basis of the alcohols containing the group - NH -. With the increasing solubility of the branching alkoxides increases in hydrocarbon solvents. Found that sodium alkoxide hydroxypropyl aniline decane insoluble, the sodium alcoholate hydroxypropyl toluidine soluble in decane. The results of studies of the effect of mixed alkoxides oxypropylated aromatic secondary amines on the structure of diene polymers. The Providing the necessary initiation systems for preparing functionalized polymers. It was revealed that secondary amines from which the lithium amides are inactive, so the polymerization of monomers was carried out in the presence of electron as that used glycol ethers - diglyme, THF, 2,2 - ditetragidrofurfuril propane, which increase polymer-filler interaction. The results of research of the microstructure of the diene part of SBR obtained in the mixed alkali metal alkoxide with a mixture of lapromol alcohols, toluidine and TGFS showed that increasing toluidine consisting of mixed modifier reduces

  14. Stimuli-responsive cement-reinforced rubber.

    Science.gov (United States)

    Musso, Simone; Robisson, Agathe; Maheshwar, Sudeep; Ulm, Franz-Josef

    2014-05-14

    In this work, we report the successful development of a cement-rubber reactive composite with reversible mechanical properties. Initially, the composite behaves like rubber containing inert filler, but when exposed to water, it increases in volume and reaches a stiffness that is intermediate between that of hydrogenated nitrile butadiene rubber (HNBR) and hydrated cement, while maintaining a relatively large ductility characteristic of rubber. After drying, the modulus increases even further up to 400 MPa. Wet/drying cycles prove that the elastic modulus can reversibly change between 150 and 400 MPa. Utilizing attenuated total reflection Fourier transform infrared spectroscopy), we demonstrate that the high pH produced by the hydration of cement triggers the hydrolysis of the rubber nitrile groups into carboxylate anions. Thus, the salt bridges, generated between the carboxylate anions of the elastomer and the cations of the filler, are responsible for the reversible variations in volume and elastic modulus of the composite as a consequence of environmental moisture exposure. These results reveal that cement nanoparticles can successfully be used to accomplish a twofold task: (a) achieve an original postpolymerization modification that allows one to work with carboxylate HNBR (HXNBR) not obtained by direct copolymerization of carboxylate monomers with butadiene, and (b) synthesize a stimuli-responsive polymeric composite. This new type of material, having an ideal behavior for sealing application, could be used as an alternative to cement for oil field zonal isolation applications.

  15. On Optimizing an Archibald Rubber-Band Heat Engine.

    Science.gov (United States)

    Mullen, J. G.; And Others

    1978-01-01

    Discusses the criteria and procedure for optimizing the performance of Archibald rubber-band heat engines by using the appropriate choice of dimensions, minimizing frictional torque, maximizing torque and balancing the rubber band system. (GA)

  16. Psychomotor Effects of Mixed Organic Solvents on Rubber Workers

    Directory of Open Access Journals (Sweden)

    O Aminian

    2014-04-01

    Full Text Available Background: Exposure to organic solvents is common among workers. Objective: To assess neurobehavioral effects of long-term exposure to organic solvents among rubber workers in Tehran, Iran. Methods: Across-sectional study was conducted on 223 employees of a rubber industry. The participants completed a data collection sheet on their occupational and medical history, and demographic characteristics including age, work experience, education level; they performed 6 psychiatric tests on the neurobehavioral core test battery (NCTB that measure simple reaction time, short-term memory (digit span, Benton, eye-hand coordination (Purdue pegboard, pursuit aiming, and perceptual speed (digit symbol. Results: Workers exposed and not exposed to organic solvents had similar age and education distribution. The mean work experience of the exposed and non-exposed workers was 5.9 and 4.4 years, respectively. The exposed workers had a lower performance compared to non-exposed workers in all psychomotor tests. After controlling for the confounders by logistic regression analysis, it was found that exposure to organic solvents had a significant effect on the results of digit symbols, digit span, Benton, aiming, and simple reaction time tests. No significant effect was observed in pegboard test. Conclusion: Occupational exposure to organic solvent can induce subtle neurobehavioral changes among workers exposed to organic solvents; therefore, periodical evaluation of the central nervous system by objective psychomotor tests is recommended among those who are chronically exposed to organic solvents.

  17. Study for the degumming pretreatment of rubber seed oil

    Science.gov (United States)

    Li, X. Y.; Chen, Y. B.; Zhang, X.; Souliyathai, D.; Yang, S. P.; Wang, Q.

    2017-11-01

    With the rapid development of the aviation industry, appearing of the aviation carbon tax and the increasingly serious environmental problems have forced the world to research the development of renewable bio-aviation fuel. Renewable biological aviation fuel contains phosphorus that could reduce the synthesis of noble metal catalysts such as Pd, Pt activity. In order to get low content of phosphorus in degummed oil of non-edible vegetable oil, in this paper, with rubber seed oil as raw material, making the experiment of single factor at the influence of temperature, stirring speed, adding amount of monoethanolamine (MEA) and water amount. The experimental results show that the added amount of MEA is 2.5% in the weight of oil, and temperature is 60°C, while the amount of added water is 2% in the weight of oil, reaction time is 40 min, and stirring speed is 200 r/min. Under these conditions, the phosphorus content of rubber seed oil can be reduced to below 3 mg/kg, degumming rate is 91.37%, and the degumming effects are obvious, which also provides some foundation for follow-up studies.

  18. Electron linear accelerator system for natural rubber vulcanization

    Science.gov (United States)

    Rimjaem, S.; Kongmon, E.; Rhodes, M. W.; Saisut, J.; Thongbai, C.

    2017-09-01

    Development of an electron accelerator system, beam diagnostic instruments, an irradiation apparatus and electron beam processing methodology for natural rubber vulcanization is underway at the Plasma and Beam Physics Research Facility, Chiang Mai University, Thailand. The project is carried out with the aims to improve the qualities of natural rubber products. The system consists of a DC thermionic electron gun, 5-cell standing-wave radio-frequency (RF) linear accelerator (linac) with side-coupling cavities and an electron beam irradiation apparatus. This system is used to produce electron beams with an adjustable energy between 0.5 and 4 MeV and a pulse current of 10-100 mA at a pulse repetition rate of 20-400 Hz. An average absorbed dose between 160 and 640 Gy is expected to be archived for 4 MeV electron beam when the accelerator is operated at 400 Hz. The research activities focus firstly on assembling of the accelerator system, study on accelerator properties and electron beam dynamic simulations. The resonant frequency of the RF linac in π/2 operating mode is 2996.82 MHz for the operating temperature of 35 °C. The beam dynamic simulations were conducted by using the code ASTRA. Simulation results suggest that electron beams with an average energy of 4.002 MeV can be obtained when the linac accelerating gradient is 41.7 MV/m. The rms transverse beam size and normalized rms transverse emittance at the linac exit are 0.91 mm and 10.48 π mm·mrad, respectively. This information can then be used as the input data for Monte Carlo simulations to estimate the electron beam penetration depth and dose distribution in the natural rubber latex. The study results from this research will be used to define optimal conditions for natural rubber vulcanization with different electron beam energies and doses. This is very useful for development of future practical industrial accelerator units.

  19. Lifetime Analysis of Rubber Gasket Composed of Methyl Vinyl Silicone Rubber with Low-Temperature Resistance

    Directory of Open Access Journals (Sweden)

    Young-Doo Kwon

    2015-01-01

    Full Text Available Most machines and instruments constantly require elastomeric materials like rubber for the purposes of shock absorption, noise attenuation, and sealing. The material properties and accurate lifetime prediction of rubber are closely related to the quality of machines, especially their durability and reliability. The properties of rubber-like elastomers are influenced by ambient conditions, such as temperature, environment, and mechanical load. Moreover, the initial properties of rubber gaskets must be sustained under working conditions to satisfy their required function. Because of its technical merits, as well as its low cost, the highly accelerated life test (HALT is used by many researchers to predict the long-term lifetime of rubber materials. Methyl vinyl silicone rubber (VMQ has recently been adopted to improve the lifetime of automobile radiator gaskets. A four-parameter method of determining the recovery ability of the gaskets was recently published, and two revised methods of obtaining the recovery were proposed for polyacrylate (ACM rubber. The recovery rate curves for VMQ were acquired using the successive zooming genetic algorithm (SZGA. The gasket lifetime for the target recovery (60% of a compressed gasket was computed somewhat differently depending on the selected regression model.

  20. Mechanical Properties of Graphene-Rubber Nanocomposites

    Science.gov (United States)

    Anhar, N. A. M.; Ramli, M. M.; Hambali, N. A. M. A.; Aziz, A. A.; Mat Isa, S. S.; Danial, N. S.; Abdullah, M. M. A. B.

    2017-11-01

    This research focused on development of wearable sensor device by using Prevulcanized Natural Rubber (PV) and Epoxidized Natural Rubber (ENR 50) latex incorporated with graphene oxide (GO), graphene paste, graphene powder and reduced graphene oxide (rGO) powder. The compounding formulation and calculation were based on phr (parts per hundred rubber) and all the samples were then tested for mechanical properties using Instron 5565 machine. It was found that the sonication effects on tensile strength may have better quality of tensile strength compared to non-sonicated GO. For PV incorporate GO, the optimum loading was best determined at loading 1.5 phr with or without sonication and similar result was recorded for PV/G. For ENR 50 incorporate graphene paste and rGO powder nanocomposite shows the best optimum was at 3.0 phr with 24 hours’ sonication.

  1. Vulcanization and the mechanical response of rubber

    Science.gov (United States)

    Kundurthi, S.; Mythravaruni, P.; Ravindran, P.

    2015-06-01

    Hyperelastic models are widely used to describe the mechanical response of rubber. However, purely mechanical models cannot account for changes in the material due to chemical reactions such as those that take place during vulcanization. Here, we present a model developed within a thermodynamic framework accounting for chemical reactions. A mixture theory approach that allows for the existence of multiple species and their interconversion is followed. The existence of a Helmholtz potential and a rate of entropy production function for the mixture as a whole are posited. Following the multiple natural configuration approach, the rate of entropy production is maximized to obtain constitutive equations. The viscoelastic model is then specialized to the elastic case. The model is calibrated using data available in the literature for rubber. A simulation of the stress-strain curve of rubber as vulcanization progresses is presented.

  2. Synergistic effect of plasma-modified halloysite nanotubes and carbon black in natural rubber-butadiene rubber blend

    NARCIS (Netherlands)

    Poikelispaa, Minna; Das, Amit; Dierkes, Wilma K.; Vuorinen, Jyrki

    2013-01-01

    Halloysite nanotubes (HNTs) were investigated concerning their suitability for rubber reinforcement. As they have geometrical similarity with carbon nanotubes, they were expected to impart a significant reinforcement effect on the rubber compounds but the dispersion of the nanofillers is difficult.

  3. The use of plasticizing additives based on recycled raw materials in the petrochemical rubber mixtures

    Directory of Open Access Journals (Sweden)

    Z. S. Shashok

    2016-01-01

    Full Text Available At present, the development of alternative products for elastomers based on recycling petrochemical raw materials is a new trend of the rubber industry progress. Petrochemical raw materials include spent lubricants and motor oils are among such recycling products. In this context, the influence of the products of recycling waste engine oil (DVCH and RA in comparison with industrial oil (I-20 on the technological properties of filled elastomeric compositions was investigated. The elastomeric compositions were based on poly isoprene and divinyl rubbers. The plasticizing components were manufactured by IOOO “DVCH-Menedzhment”. They are mixture of hydro-carbons, C16–C20 and differ from each other in the content of linear and branched paraffin. Plastic-elastic properties of rubber compounds on the shear disk viscometer MV2000 in accordance with GOST 10722–76 was carried out. Kinetics of vulcanization on the rheometer ODR2000 according to GOST 12535–84 was defined. It is shown that the introduction of RA test plasticizing component provides a significant effect on Mooney viscosity, as compared to elastomeric compositions containing a plasticizer and I-20 and plasticizing additive DVCH. It revealed that the administration of all components in the studied plasticizing elastomer compositions based on a combination poly isoprene and divinyl rubbers has no significant effect on the rate of relaxation of stress of rubber compounds. It is found that elastomeric compositions containing as additives investigated processing waste oil products (DVCH and RA are characterized by a slightly smaller value of time to reach an optimal degree of vulcanization.

  4. Economic status, smoking, occupational exposure to rubber, and lung cancer: a case-cohort study.

    Science.gov (United States)

    Li, Ke; Yu, Shunzhang

    2002-05-01

    Recent studies tend consistently to confirm the presence of a moderate excess risk of lung cancer in the rubber industry. However, the agent responsible for the excess of lung cancer is still obscure. Also, analyses without regard to the modifying effects of sex, economic status, and smoking habit are less than satisfactory. To explore these questions, we have conducted a case-cohort study using the data of 51 lung cancer deaths in 1973-1997 and a random sample (sub-cohort) of 188 from among 1598 subjects in a rubber factory in Shanghai, China. We computed the risks of lung cancer by economic status, smoking habit, coal fumes in home, and year of first employment. We assessed lung cancer risks for occupational exposures, unadjusted and adjusted for economic status and smoking. After confounding effects of smoking and economic status were controlled, we found that rate ratios were 1.43 (95% confidence interval (CI) 0.43-4.69), 1.79 (95% CI 0.64-5.03), and 3.76 (95% CI 1.44-9.86) for 1-14, 15-29, and 30-45 exposure-years in curing department, respectively. The data showed significant trends in increased risk of lung cancer with duration of exposure in tire-curing department (score test for trend:, P = 0.004). However, in front rubber processing (weighing and mixing, calendering, extruding, and milling), no significant excess risk of lung cancer was found. If it can be confirmed that nitrosamines are mainly generated in back rubber processing (curing and vulcanizing), it would be reasonable to conclude that excess risk of lung cancer in rubber industry is attributable, at least partially, to exposure to nitrosamines.

  5. 27 CFR 21.125 - Rubber hydrocarbon solvent.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Rubber hydrocarbon solvent. 21.125 Section 21.125 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU....125 Rubber hydrocarbon solvent. (a) Rubber hydrocarbon solvent is a petroleum derivative. (b...

  6. Economic analysis of intercropping rubber ( Hevea Brasiliensis ) in ...

    African Journals Online (AJOL)

    This study was carried out in 2007/2008 planting season to evaluate the economics of intercropping rubber among smallholder rubber farmers of Edo and Delta States, through a survey of 54 rubber farmers in a multi stage, purposive and simple random sampling techniques. Data collected were analyzed using budgetary ...

  7. Adoption of improved rubber production technologies by farmers in ...

    African Journals Online (AJOL)

    This study examined the adoption of improved rubber production technologies by farmers in Akwa Ibom State, Nigeria. The specific objectives of the study are to; identify improved rubber production technologies disseminated to farmers, identify methods for disseminating information on improved rubber production ...

  8. Modified Silicone-Rubber Tooling For Molding Composite Parts

    Science.gov (United States)

    Baucom, Robert M.; Snoha, John J.; Weiser, Erik S.

    1995-01-01

    Reduced-thermal-expansion, reduced-bulk-modulus silicone rubber for use in mold tooling made by incorporating silica powder into silicone rubber. Pressure exerted by thermal expansion reduced even further by allowing air bubbles to remain in silicone rubber instead of deaerating it. Bubbles reduce bulk modulus of material.

  9. An overview of the potentials of natural rubber (Hevea brasiliensis ...

    African Journals Online (AJOL)

    STORAGESEVER

    2009-12-29

    Dec 29, 2009 ... An overview of the potentials of natural rubber (Hevea ... prospects and potentials of transgenic rubber plant as a unique .... tapping is a non-destructive method of latex extraction .... markers have been developed for the rubber tree. Genes ... the International Symposium on Molecular Farming in Plants Asia.

  10. Economic Analysis of Intercropping Rubber (Hevea brasiliensis) in ...

    African Journals Online (AJOL)

    Mr D.Y. Giroh

    This study was carried out in 2007/2008 planting season to evaluate the economics of intercropping rubber among smallholder rubber farmers of Edo and Delta States, through a survey of 54 rubber farmers in a multi stage, purposive and simple random sampling techniques. Data collected were analyzed using budgetary ...

  11. Thermoreversibly Cross-Linked EPM Rubber Nanocomposites with Carbon Nanotubes

    NARCIS (Netherlands)

    Polgar, Lorenzo Massimo; Criscitiello, Francesco; van Essen, Machiel; Araya-Hermosilla, Rodrigo; Migliore, Nicola; Lenti, Mattia; Raffa, Patrizio; Picchioni, Francesco; Pucci, Andrea

    2018-01-01

    Conductive rubber nanocomposites were prepared by dispersing conductive nanotubes (CNT) in thermoreversibly cross-linked ethylene propylene rubbers grafted with furan groups (EPM-g-furan) rubbers. Their features were studied with a strong focus on conductive and mechanical properties relevant for

  12. An overview of the potentials of natural rubber ( Hevea brasiliensis ...

    African Journals Online (AJOL)

    The International Rubber Research Organizations have successfully developed transgenic rubber plants that produce foreign proteins of potential commercial value. Among such routines is an antibody and human serum albumin. Tapping rubber trees for valuable proteins will be more profitable compared to other options.

  13. Investigations on cementitious composites based on rubber particle waste additions

    Directory of Open Access Journals (Sweden)

    Glaucio Laun Nacif

    2012-01-01

    Full Text Available The amount of waste rubber has gradually increased over recent years because of over-growing use of rubber products. The disposal of waste rubber has caused serious environmental problems. The incorporation of recycled materials into cementitious composites is a feasible alternative that has gained ground in civil construction. The performance of such materials is much affected not only by the rubber addition, but also the particle size which has been controversially reported in the literature. In order to investigate the single effect of rubber particles into cement based materials, rubber cementitious composites were prepared with no silica particle additions. A full factorial design has been conducted to assess the influence of the rubber particle size (0.84/0.58 mm and 0.28/0.18 mm; mass fraction used (5, 15 and 30%; and water/cement ratio (0.35 and 0.50 on the physic-mechanical properties of the composites. The materials were characterized through apparent density, porosity, compressive strength, flexural strength, modulus of elasticity and microstructural analysis. The interactions of rubber particle size, rubber fraction and water/cement ratio affected significantly the density and compressive strength of the composites. The apparent porosity was influenced mainly by the rubber particle size. The flexural strength was affected by the main factors and the modulus of elasticity was affected by the interaction factors rubber particle size and fraction, and rubber fraction and w/c ratio.

  14. Investigations on cementitious composites based on rubber particle waste additions

    Directory of Open Access Journals (Sweden)

    Glaucio Laun Nacif

    2013-04-01

    Full Text Available The amount of waste rubber has gradually increased over recent years because of over-growing use of rubber products. The disposal of waste rubber has caused serious environmental problems. The incorporation of recycled materials into cementitious composites is a feasible alternative that has gained ground in civil construction. The performance of such materials is much affected not only by the rubber addition, but also the particle size which has been controversially reported in the literature. In order to investigate the single effect of rubber particles into cement based materials, rubber cementitious composites were prepared with no silica particle additions. A full factorial design has been conducted to assess the influence of the rubber particle size (0.84/0.58 mm and 0.28/0.18 mm; mass fraction used (5, 15 and 30%; and water/cement ratio (0.35 and 0.50 on the physic-mechanical properties of the composites. The materials were characterized through apparent density, porosity, compressive strength, flexural strength, modulus of elasticity and microstructural analysis. The interactions of rubber particle size, rubber fraction and water/cement ratio affected significantly the density and compressive strength of the composites. The apparent porosity was influenced mainly by the rubber particle size. The flexural strength was affected by the main factors and the modulus of elasticity was affected by the interaction factors rubber particle size and fraction, and rubber fraction and w/c ratio.

  15. Effect of micro sized marble sludge on physical properties of natural rubber composites

    Directory of Open Access Journals (Sweden)

    Ahmed Khalil

    2013-01-01

    Full Text Available Marble waste as sludge is collected from Marble industry, as a way of solving the environmental problem of industrial waste. The sludge was dried, ground and passed through desire sieves (10, 15, 20, 37 and 75 μm, This powder was characterized by the X-ray fluorescence technique and then incorporated in the formulation of NR composites with different loading of micro sized MS particles (20, 40, 60, 80 and 100 parts per hundred of rubber, phr. The cure characteristics, mechanical properties and swelling properties of MS/NR composites were evaluated. Results indicate that minimum torque, maximum torque, tensile strength, modulus, tear strength, hardness, crosslink density were increased while the scorch time, cure time, cure rate, cure rate index (CRI, elongation at break, compression set, rebound resilience, abrasion loss, swelling coefficient, average molecular weight and filler-rubber interaction decrease with increasing MS loading.

  16. Replacement of Carbon Black on Natural Rubber Composites and Nanocomposites — Part 1

    Science.gov (United States)

    Martín-Cortés, Guillermo R.; Esper, Fabio J.; de Araujo, Antonio J. Santana; Hennies, Wildor T.; Valenzuela, Maria G. Silva; Valenzuela-Díaz, Francisco R.

    Seeking to replace carbon-black as filler of rubber in the production of vulcanized goods, researchers from University of São Paulo have studied different materials types as minerals, vegetal or wastes agricultural and industry. Results of rubber composites filled with MA1 a waste of mineral treatment provided by Esper Industries are presented. MA1 was characterized through X-ray diffraction; Thermal analysis; Scanning Electronic Microscopy; and others laboratory methods. The composite and shaped masses were evaluated by these methods plus their mechanical properties such as tensile strength, elongation at break and hardness. Exceptional results were obtained in the mechanical properties evaluated, better than those obtained with the traditional carbon-black. Seeing the kind of material used as filler, it can conclude that the environmental benefit is present, as well as economic development, giving credibility to the use of these alternative material in replacement carbonblack.

  17. STUDY ON HEAT DYNAMIC LOADING OF RUBBER

    Directory of Open Access Journals (Sweden)

    T. I. Igumenova

    2015-01-01

    Full Text Available A number of studies on heat buildup in tire rubber surface scan method samples using a thermal imaging camera. Investigated the exothermic chemical reaction mechanical destruction rubber when loading designs permanent cyclic stretching with deformation of the working zone 50%. Percentage of deformation of the working zone was chosen on the basis of the actual data on the stretch-compression zone "Rusk" tires, which is the maximum level difference of deformation during run-in. Experiment plan provided for periodic relaxation samples of at least 72 hours for more accurate simulation of operation process of structural products. Created and processed data on temperature changes in samples for bar and line profile for rubber compounds with the introduction of nanomodifiers (fulleren technical carbon in comparison with the control sample without him. The data obtained reflect the nature of heat depending on the composition of the compound. Identified common patterns of thermal nature of physico-chemical process mechanical destruction rubbers. For rubber with nanomodifikatorom there has been an increase in the temperature interval reaction from a minimum to a maximum 2 degrees that is also linked to the rise in the average temperature of the reaction on the histogram also at 2-3 degrees of deformation under the same conditions and the level of cyclic loading. However, the temperature in the control sample that is associated with the beginning of the formation of hardened rubber structures, economies of Mallinz-Petrikeev, occurs with delay twice compared with modified Fullerenes. Measurement of physic-mechanical indicators selected in the course of testing of samples showed the beginning of formation of structure with increased strength of samples in the sample temperature zone that corresponds to the thermal effect of èndotermičeskomu recombination reactions of macromolecules.

  18. Cancer mortality and occupational exposure to aromatic amines and inhalable aerosols in rubber tire manufacturing in Poland.

    NARCIS (Netherlands)

    de Vocht, F.; Sobala, W.; Wilczynska, U.; Kromhout, H.; Szeszenia-Dabrowska, N.; Peplonska, B.

    2009-01-01

    AIM: Most data on carcinogenic risk in the rubber industry are based on data from Western countries. This study assessed cancer risks in a retrospective cohort in a Polish tire manufacturing plant, relying on quantified exposure to inhalable aerosols and aromatic amines instead of job titles or

  19. Oxygen exchange in silicone rubber capillaries.

    Science.gov (United States)

    Heineken, F G; Predecki, P K; Filley, G F

    1978-06-01

    Capillaries of 7 and 12.5 mu diameter have been fabricated in silicone rubber. Whole blood treated with heparin has been perfused through these capillaries. Under flowing conditions, no clotting or other clumping effects have been observed and red cells appear to maintain a constant velocity. Oxygen transfer data to and from saline perfusing the 12.5 mu diameter capillaries have been obtained in order to determine how rapidly O2 will permeate the silicone rubber film. The data indicate that the capillaries simulate lung tissue oxygen exchange and will allow for the first time the experimental determination of oxygen exchange kinetics in flowing whole blood.

  20. Rheological testing of crumb rubber modified bitumen

    CSIR Research Space (South Africa)

    Mturi, GAJ

    2011-08-01

    Full Text Available are shown in Table 1, typically (Xiao et al., 2006) containing Carbon, Oxygen, Silicon, Sulphur and traces of the metals: Calcium, Sodium, Aluminium and Zinc from the vulcanization component, Zinc Oxide (ZnO) (Mark et al., 2005). 3-5 August... for The relationship between the optimum gap distance and the rubber crumb particle size was calculated. The gap distance was found to be between the rubber crumb particles prior to blending determined through extraction as suggested by Attia and Abdelrahman...

  1. The Treatment of Sludge from the Rubber Processing Industry with ...

    African Journals Online (AJOL)

    ... readily available, cheap and easy to handle, more biodegradable, therefore more environmentally friendly. The use of the coagulant for the treatment of sludge and indeed where coagulation and flocculation is desirous can be so recommended. Keywords: Biodegradable, Chitosan, Exoskeleton, Pollution, Sludge,.

  2. Treatment of wastewater from rubber industry in Malaysia

    African Journals Online (AJOL)

    GREGORY

    2010-09-20

    Sep 20, 2010 ... producing the biogas as a useful energy sources are some advantages of anaerobic wastewater treatment system (Kantachote et al., 2008). However, this treatment results in the formation of H2S due to consumption of sulphate instead of oxygen by sulphate-reducing bacteria. H2S is toxic and increases ...

  3. Small scale industrial application of rubber seed oil in soap ...

    African Journals Online (AJOL)

    Its pH was slightly basic which makes it suitable for use in soap manufacture. It was, therefore, used as a substitute for palm kernel oil in the production of soaps (bar soap and detergent soap). Tests for the foam capacity and stability of the soaps exhibited good visual foam stabilities and capacities. These make it suitable for ...

  4. Constraints to sustainable development of rubber industry in Nigeria ...

    African Journals Online (AJOL)

    The findings revealed that lack of inputs, lack of credit facilities, high production cost are some of the constraints to sustainable development. The study also revealed among others the causes of the constraints, which include high lending interest rate, diversion of loan by farmers, low exchange rate of the Naira and old age ...

  5. Treatment of wastewater from rubber industry in Malaysia ...

    African Journals Online (AJOL)

    African Journal of Biotechnology. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 9, No 38 (2010) >. Log in or Register to get access to full text downloads.

  6. SURFACE APPLICATION OF ANTIOZONANTS TO RUBBER ITEMS AND EVALUATION OF ANTIOZONANTS FOR PACKAGING RUBBER ITEMS IN PLASTIC BAGS

    Science.gov (United States)

    Research was conducted to develop methods of surface applications of antiozonants to rubber items and evaluate antiozonants for packaging rubber...items in plastic bags. The report covers (1) tests of packaging rubber items in polyethylene bags together with various antiozonants , and (2) tests of

  7. In situ reactive compatibilization of natural rubber/acrylic-bentonite composites via peroxide-induced vulcanization

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Lihua; Lei, Zhiwen [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Xu, Chuanhui, E-mail: xuhuiyee@gxu.edu.cn [Guangxi Key Laboratory of Petrochemical Resource Processing and Process Intensification Technology, School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Chen, Yukun, E-mail: cyk@scut.edu.cn [The Key Laboratory of Polymer Processing Engineering, Ministry of Education, China(South China University of Technology), Guangzhou, 510640 (China)

    2016-02-15

    To achieve good interfacial interaction between fillers and rubber matrix is always a hot topic in rubber reinforcing industry. In this paper, acid activated bentonite (Bt) was alkalified to be alkaline calcium-bentonite (ACBt), then acrylic acid (AA) was employed to modify ACBt to obtain acrylic-bentonite (ABt). The results of Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) illustrated that acrylate groups were chemically boned onto the surface of Bt and the layer spacing of Bt was increased. During peroxide-induced vulcanization, in situ compatibilization of ABt was realized via the reaction between the unsaturated bonds of acrylate groups on the surface of Bt and the natural rubber (NR) chains. This resulted in an enhanced cross-linked network which contributed to the improved mechanical properties of NR/ABt composites. - Highlights: • Acrylate groups were chemically boned onto the surface of bentonite. • In situ compatibilization was realized via the reaction of acrylate group and NR. • ABt particles participated in forming the NR crosslink network. • A potential reinforcing material options for “white” rubber products.

  8. Simulation Process Analysis of Rubber Shock Absorber for Machine Tool

    Directory of Open Access Journals (Sweden)

    Chai Rong Xia

    2016-01-01

    Full Text Available The simulation on rubber shock absorber of machine tool was studied. The simple material model of rubber was obtained by through the finite element analysis software ABAQUS. The compression speed and the hardness of rubber material were considered to obtain the deformation law of rubber shock absorber. The location of fatigue were confirmed from the simulation results. The results shown that the fatigue position is distributed in the corner of shock absorber. The degree of deformation is increased with increasing of compress speed, and the hardness of rubber material is proportional to deformation.

  9. Investigation of surface halide modification of nitrile butadiene rubber

    Science.gov (United States)

    Sukhareva, K. V.; Mikhailov, I. A.; Andriasyan, Yu O.; Mastalygina, E. E.; Popov, A. A.

    2017-12-01

    The investigation is devoted to the novel technology of surface halide modification of rubber samples based on nitrile butadiene rubber (NBR). 1,1,2-trifluoro-1,2,2-trichlorethane was used as halide modifier. The developed technology is characterized by production stages reduction to one by means of treating the rubber compound with a halide modifier. The surface halide modification of compounds based on nitrile butadiene rubber (NBR) was determined to result in increase of resistance to thermal oxidation and aggressive media. The conducted research revealed the influence of modification time on chemical resistance and physical-mechanical properties of rubbers under investigation.

  10. Preparation of sulfonic acid-containing rubbers from natural rubber vulcanizates

    Science.gov (United States)

    Poonsawat, Worapong; Poompradub, Sirilux; Ngamcharussrivichai, Chawalit

    2014-06-01

    In this work, a series of sulfonic acid-containing rubbers were prepared by aqueous phase oxidation of natural rubber vulcanizates in the presence of hydrogen peroxide (H2O2) and formic acid (HCOOH). The starting vulcanizates were neatly prepared via an efficient vulcanization (EV) system by varying mass ratio of N-cyclohexyl-2-benzothiazole sulfonamide (CBS), as an accelerator, to sulfur. The oxidation conditions were controlled at the molar ratio of H2O2: HCOOH = 1:1, the concentration of H2O2 = 15 wt.%, the temperature = 50 °C, and the reaction time = 3 h. The rubber materials before and after the oxidation were characterized for their physicochemical properties by using Fourier transform infrared spectroscopy, bomb calorimetry, acid-base titration and swelling measurements. The results indicated the presence of sulfonic acid group in the oxidized rubbers, generated by the oxidative cleaves of sulfide crosslinks in the rubber vulcanizates. The oxidation decreased the sulfur content of the rubber in which the level of sulfur loss was determined by the CBS/sulfur ratio. Moreover, the acidity of the oxidized products was correlated with the amount of sulfur remaining.

  11. Filled liquid silicone rubbers: Possibilities and challenges

    DEFF Research Database (Denmark)

    Yu, Liyun; Vudayagiri, Sindhu; Zakaria, Shamsul Bin

    2014-01-01

    Liquid silicone rubbers (LSRs) have been shown to possess very favorable properties as dielectric electroactive polymers due to their very high breakdown strengths (up to 170 V/μm) combined with their fast response, relatively high tear strength, acceptable Young’s modulus as well as they can...

  12. Rubber Recycling: Chemistry, Processing, and Applications

    NARCIS (Netherlands)

    Myhre, M.; Saiwari, Sitisaiyidah; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2012-01-01

    For both environmental and economic reasons, there is broad interest in recycling rubber and in the continued development of recycling technologies. The use of postindustrial materials is a fairly well-established and documented business. Much effort over the past decade has been put into dealing

  13. Chemical changes in rubber allergens during vulcanization.

    Science.gov (United States)

    Bergendorff, Ola; Persson, Christina; Lüdtke, Anna; Hansson, Christer

    2007-09-01

    Allergic contact dermatitis to rubber is caused by residues of chemicals used in manufacturing a rubber product. Several different additives are used to achieve a final product of the desired characteristics. Accelerators such as thiurams, dithiocarbamates, and mercaptobenzothiazoles are often among the additives responsible for allergic reactions recognized by dermatologists. The chemistry of the vulcanization process is complicated; as it occurs at an elevated temperature with a mixture of reactive chemicals, the compositions of the initial and final products differ. This paper investigates the changes in composition of common allergens during vulcanization, doing so by chemically analysing various rubber formulations at different stages of the process. Major changes were found in which added chemicals were consumed and new ones produced. An important observation is that thiuram disulfides rarely appear in the final rubber although they may have been used as additives. Instead, thiurams are often converted to dithiocarbamates or to products formed by addition to mercaptobenzothiazole structures, if these have been used together with thiurams as accelerators.

  14. Valorisation of Proteins from Rubber Tree

    NARCIS (Netherlands)

    Widyarani,; Coulen, Stef C.W.; Sanders, Johan P.M.; Bruins, Marieke E.

    2017-01-01

    Purpose: The objective of this study was to identify the availability, possible applications, and economic potential of proteins that are present in different parts of the rubber tree. Proteins from non-food sources can be used in e.g. animal feed or biochemicals production with no or little

  15. Numerical modelling of rubber vibration isolators

    NARCIS (Netherlands)

    Beijers, C.A.J.; de Boer, Andries; Nilsson, A.; Boden, H.

    2003-01-01

    An important cause for interior noise in vehicles is structure-borne sound from the engine. The vibrations of the source (engine) are transmitted to the receiver structure (the vehicle) causing interior noise in the vehicle. For this reason the engine is supported by rubber isolators for passive

  16. Why Do Calculators Have Rubber Feet?

    Science.gov (United States)

    Heavers, Richard M.

    2007-01-01

    Our students like using the covers of their TI graphing calculators in an inquiry-based extension of a traditional exercise that challenges their preconceived ideas about friction. Biology major Fiona McGraw (Fig. 1) is obviously excited about the large coefficient of static friction ([mu][subscript s] = 1.3) for the four little rubber feet on her…

  17. Investigation of chlorinated modifier content influence on the physical-mechanical properties and vulcanizing characteristics of rubber and rubber mixture

    Science.gov (United States)

    Sukhareva, K. V.; Mikhailov, I. A.; Andriasyan, Yu O.; Popov, A. A.

    2017-12-01

    Present paper is devoted to the novel solution for the chlorination technology of polyolefin and diene rubbers – mechanochemical halide modification, as a more efficient way to obtain halogenated elastomers with a wide range of halogen content (from 3 to 7 %). The vulcanizing characteristics of elastomeric compounds based on the chlorinated rubber compounds as well as the production conditions of vulcanization process have been studied by the methods of dynamic mechanical rheometry. The performed investigation revealed the influence of chlorine content in different types of rubber compounds on rheological and physical-mechanical properties. New halogen-containing polyolefins rubbers produced by this technology proved themselves in the conditions of the rubber production.

  18. Cancer mortality and morbidity among rubber workers.

    Science.gov (United States)

    Monson, R R; Fine, L J

    1978-10-01

    Mortality and morbidity from cancer among a cohort of 13,570 white male rubber workers were examined. Each man worked for at least 5 years at the Akron, Ohio, plant of the B. F. Goodrich Company. The potential period of follow-up was from January 1, 1940 to June 30, 1976. Departmental work histories were based primarily on records maintained by Local no. 5, United Rubber Workers. The occurrence of cancer was measured by death certificates and by a survey of Akron-area hospital tumor registries from 1964 to 1974. Two types of analyses were made: 1) an external comparison of mortality rates of rubber workers versus rates of U.S. white males, and 2) an internal comparison of cancer morbidity rates among persons who were employed in various work areas of the plant. Excess cases of specific cancers (observed/expected numbers) among workers in specific work areas included: stomach and intestine: rubber making (30/14.4); lung: tire curing (31/14.1), fuel cells and/or deicers (46/29.1); bladder: chemical plant (6/2.4), and tire building (16/10.7); skin cancer: tire assembly (12/1.9); brain cancer: tire assembly (8/2.0); lymphatic cancer: tire building (8/3.2); and leukemia: calendering (8/2.2), tire curing (8/2.6), tire building (12/7.5), elevators (4/1.4), tubes (4/1.6), and rubber fabrics (4/1.1). Agents that may be responsible for these excesses were considered.

  19. Molecular mechanism of ethylene stimulation of latex yield in rubber tree (Hevea brasiliensis) revealed by de novo sequencing and transcriptome analysis.

    Science.gov (United States)

    Liu, Jin-Ping; Zhuang, Yu-Fen; Guo, Xiu-Li; Li, Yi-Jian

    2016-03-24

    Rubber tree (Hevea brasiliensis) is an important industrial crop cultivated in tropical areas for natural rubber production. Treatment of the bark of rubber trees with ehephon (an ethylene releaser) has been a routine measure to increase latex yield, but the molecular mechanism behind the stimulation of rubber production by ethylene still remains a puzzle. Deciphering the enigma is of great importance for improvement of rubber tree for high yield. De novo sequencing and assembly of the bark transciptomes of Hevea brasiliensis induced with ethephon for 8 h (E8) and 24 h (E24) were performed. 51,965,770, 52,303,714 and 53,177,976 high-quality clean reads from E8, E24 and C (control) samples were assembled into 81,335, 80,048 and 80,800 unigenes respectively, with a total of 84,425 unigenes and an average length of 1,101 bp generated. 10,216 and 9,374 differentially expressed genes (DEGs) in E8 and E24 compared with C were respectively detected. The expression of several enzymes in crucial points of regulation in glycolysis were up-regulated and DEGs were not significantly enriched in isopentenyl diphosphate (IPP) biosynthesis pathway. In addition, up-regulated genes of great regulatory importance in carbon fixation (Calvin cycle) were identified. The rapid acceleration of glycolytic pathway supplying precursors for the biosynthesis of IPP and natural rubber, instead of rubber biosynthesis per se, may be responsible for ethylene stimulation of latex yield in rubber tree. The elevated rate of flux throughout the Calvin cycle may account for some durability of ethylene-induced stimulation. Our finding lays the foundations for molecular diagnostic and genetic engineering for high-yielding improvement of rubber tree.

  20. Preliminary studies of the rubber from unserviceable tires irradiated by electron beam

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Clecia M.; Silva, Leonardo G. Andrade e, E-mail: blgasilva@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    Nowadays there is a growth in the developing processes for modification of polymers with ionizing radiation (gamma rays, electron beam) for several industrial applications. An option is ionizing radiation process due to their capacity of inducing crosslinking and scission on a wide range of polymeric materials without initiators or chemicals products. This method has significant advantages on economical and ecological fields, when compared to chemical, thermal and mechanical process. The rubber recycling has been extensively discussed, mainly related to tire. There are reports with data about production and consumption of rubber and unserviceable tire. There is very few information about the destination of others rubber items, incineration and landfill are the main methods for elimination of unserviceable tire, however those methods are not environmentally friendly. It is necessary to study better and effective methods to recycle and to give value to rubber residue. This work is about the use of ionizing radiation for the recovery and/or reuse and processing rubber of unserviceable tire. The samples were irradiated with 200, 400 and 600 kGy radiation dose, 22.39 kGy/s dose rates, at room temperature and in the presence of air using an 1.5 MeV electron beam accelerator. The irradiated and non-irradiated samples were studied by thermogravimetry (TG). The analyses were performed from room temperature up to 600 deg C, heating rate of 10 deg C/min in the presence of nitrogen (N{sub 2}) and air. By this technique it was possible to observe the effects of the radiation dose on the weight loss. (author)

  1. Fabrication of Extrinsically Conductive Silicone Rubbers with High Elasticity and Analysis of Their Mechanical and Electrical Characteristics

    Directory of Open Access Journals (Sweden)

    Anjum Saleem

    2010-08-01

    Full Text Available Conductive plastics are attracting more and more interest in electronics due to their light weight and inability to rust, which are common problems associated with metals. The field of conducting plastics is not new. Much work has been done to impart electrical conductivity to mechanically strong polymers such as polypropylene, polycarbonate and epoxies, etc. However there is a need to fabricate more flexible and elastic conductive polymers such as conducting silicone rubbers for use in various applications. In this work silicone rubbers reinforced with conductive fillers have been fabricated for use as sensors in textiles to detect the resistance change produced by stretching or relaxing. The variations of electrical resistance have been investigated by stretching and releasing the strands of conductive rubbers as a function of time. Two types of silicone rubbers—addition cured and condensation cured—were compounded with different electrically conductive fillers, among which carbon fibers have shown the best results. The carbon fibers improved the electrical conductance of the rubbers, even in very low weight percentages. The increasing concentration of fillers decreases the elasticity of the rubber. In order to keep the original properties of silicones, the filler concentration was kept as low as possible to produce a significantly detectable signal. The fabricated compounds were analyzed for their mechanical properties by stress strain curves. Such materials find their applications in electronics, antistatic applications, sports and the automotive industry where they can be used as deformation sensors.

  2. Simulation of Rubber Friction Using Viscoelastic Behavior of Rubber and Roughness Parameters of Surfaces

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Arab Bafrani

    2013-06-01

    Full Text Available One of the most important factors that affect tire friction is surface roughness, which determines the size of the real contact area, real pressure distribution on the contact interface, and scales of mechanical engagement between viscoelastic rubber and a rough substrate. The need to predict coefficient of friction (COF for rubber on rough surfaces for applications such as traction of tires on the road surfaces led to some physical models such as Heinrich-Kluppel’s model. The current study examines the applicability of the Heinrich-Kluppel model, using different viscoelastic representations, in numerical simulations of COF for rubber, and its agreement with the experimental results. For this purpose, roughness characteristics of the surfaces and viscoelastic properties of rubber were measured by fractal analysis and dynamic-mechanical-thermal analysis (DMTA, respectively. These data were employed in the numerical code to simulate COF for a rubber sample. The model was also modified by replacing the Zener viscoelastic representation in the original model with the generalized Maxwell viscoelastic representation. On the other hand, COF for rubber was measured on the same rough surface (different sand-papers by an in-house friction tester, and results were compared with the numerical results. It was shown that computer simulation could predict the load and speed dependence of rubber friction very well. The application of the generalized Maxwell model improved agreement between the numerical and experimental results for high sliding speeds where the Zener viscoelastic model failed to predict the right trend in variation of COF with speed. This speed range was matched with the sliding velocities in the footprint of tire under rolling conditions.

  3. Genome-wide identification of rubber tree (Hevea brasiliensis Muell. Arg.) aquaporin genes and their response to ethephon stimulation in the laticifer, a rubber-producing tissue.

    Science.gov (United States)

    Zou, Zhi; Gong, Jun; An, Feng; Xie, Guishui; Wang, Jikun; Mo, Yeyong; Yang, Lifu

    2015-11-25

    Natural rubber, an important industrial raw material, is specifically synthesized in laticifers located inside the rubber tree (Hevea brasiliensis Muell. Arg.) trunk. Due to the absence of plasmodesmata, the laticifer water balance is mediated by aquaporins (AQPs). However, to date, the characterization of H. brasiliensis AQPs (HbAQPs) is still in its infancy. In this study, 51 full-length AQP genes were identified from the rubber tree genome. The phylogenetic analysis assigned these AQPs to five subfamilies, including 15 plasma membrane intrinsic proteins (PIPs), 17 tonoplast intrinsic proteins (TIPs), 9 NOD26-like intrinsic proteins (NIPs), 4 small basic intrinsic proteins (SIPs) and 6 X intrinsic proteins (XIPs). Functional prediction based on the analysis of the aromatic/arginine (ar/R) selectivity filter, Froger's positions and specificity-determining positions (SDPs) showed a remarkable difference in substrate specificity among subfamilies. Homology analysis supported the expression of 44 HbAQP genes in at least one of the examined tissues. Furthermore, deep sequencing of the laticifer transcriptome in the form of latex revealed a key role of several PIP subfamily members in the laticifer water balance, and qRT-PCR analysis showed diverse expression patterns of laticifer-expressed HbAQP genes upon ethephon treatment, a widely-used practice for the stimulation of latex yield. This study provides an important genetic resource of HbAQP genes, which will be useful to improve the water use efficiency and latex yield of Hevea.

  4. Comparative numerical study on the optimal vulcanization of rubber compounds through traditional curing and microwaves

    Science.gov (United States)

    Milani, Gabriele; Milani, Federico

    2012-12-01

    The main problem in the industrial production process of thick EPM/EPDM elements is constituted by the different temperatures which undergo internal (cooler) and external regions. Indeed, while internal layers remain essentially under-vulcanized, external coating is always over-vulcanized, resulting in an overall average tensile strength insufficient to permit the utilization of the items in several applications where it is required a certain level of performance. Possible ways to improve rubber output mechanical properties include a careful calibration of exposition time and curing temperature in traditional heating or a vulcanization through innovative techniques, such as microwaves. In the present paper, a comprehensive numerical model able to give predictions on the optimized final mechanical properties of vulcanized 2D and 3D thick rubber items is presented and applied to a meaningful example of engineering interest. A detailed comparative numerical study is finally presented in order to establish pros and cons of traditional vulcanization vs microwaves curing.

  5. Uniaxial tension test on Rubber at constant true strain rate

    Directory of Open Access Journals (Sweden)

    Sourne H.L.

    2012-08-01

    Full Text Available Elastomers are widely used for damping parts in different industrial contexts because of their remarkable dissipation properties. Indeed, they can undergo severe mechanical loading conditions, i.e., high strain rates and large strains. Nevertheless, the mechanical response of these materials can vary from purely rubber-like to glassy depending on the strain rate undergone. Classically, uniaxial tension tests are made in order to find a relation between the stress and the strain in the material at various strain rates. However, even if the strain rate is searched to be constant, it is the nominal strain rate that is considered. Here we develop a test at constant true strain rate, i.e. the strain rate that is experienced by the material. In order to do such a test, the displacement imposed by the machine is an exponential function of time. This test has been performed with a high speed hydraulic machine for strain rates between 0.01/s and 100/s. A specific specimen has been designed, yielding a uniform strain field (and so a uniform stress field. Furthermore, an instrumented aluminum bar has been used to take into account dynamic effects in the measurement of the applied force. A high speed camera enables the determination of strain in the sample using point tracking technique. Using this method, the stress-strain curve of a rubber-like material during a loading-unloading cycle has been determined, up to a stretch ratio λ = 2.5. The influence of the true strain rate both on stiffness and on dissipation of the material is then discussed.

  6. Hysteroscopic tubal occlusion with silicone rubber.

    Science.gov (United States)

    Reed, T P; Erb, R

    1983-03-01

    A new method of sterilization for women is being investigated in several outpatient centers. The technique involves flowing liquid silicone rubber into the fallopian tubes. The silicone cures in place and forms a rubbery solid plug. The catalyzed liquid silicone is pumped through a special polysulfone guide assembly that fits through the operating channel of a standard hysteroscope. On the end of the guide is a hollow premolded silicone rubber tip that fits into the cornual ostium of the tube. When the silicone cures it also cross-links to this tip so that the tip becomes part of the plug. Results as of April 1, 1982, from 350 women in the Philadelphia center suggest that proper plug formation prevents pregnancy and that the method can be applied to about 85% of properly selected women.

  7. Properties of Waste Tire Rubber Powder

    Directory of Open Access Journals (Sweden)

    M. Bekhiti

    2014-08-01

    Full Text Available Scrap tires are abundant and alarming waste. The aggregates resulting from the crushing of the waste tires are more and more used in the field of civil engineering (geotechnical, hydraulic works, light concretes, asphaltic concretes, etc.. Depending on the type of the used tires, dimensions and possible separations and treatment, the physical and mechanical characteristics of these aggregates might change. Some physical, chemical and direct shear tests were performed on three gradation classes of waste tire rubber powder. The tests results were combined with data from previous studies to generate empirical relationships between cohesion, friction angle and particle size of waste tire powder rubber. A cubic (third order regression model seems to be more appropriate compared to linear and quadratic models.

  8. Evolution of the crosslink structure in the elastomers NR and SBR

    Energy Technology Data Exchange (ETDEWEB)

    Salgueiro, W. [IFIMAT-UNCentro and CICPBA, Pinto 399, B7000GHG Tandil (Argentina)]. E-mail: wsalgue@exa.unicen.edu.ar; Somozaa, A. [IFIMAT-UNCentro and CICPBA, Pinto 399, B7000GHG Tandil (Argentina); Marzocca, A.J. [LPMPyMC, Depto. de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon I, 1428 Buenos Aires (Argentina); Consolati, G. [Dipartimento di Fisica, Politecnico di Milano, Piazza Leonardo da Vinci 32, I-20133 Milan (Italy); Quasso, F. [Dipartimento di Fisica, Politecnico di Milano, Piazza Leonardo da Vinci 32, I-20133 Milan (Italy)

    2007-02-15

    An experimental positron annihilation lifetime spectroscopy (PALS), differential scanning calorimetry (DSC) and small angle X-ray scattering (SAXS) study of the effect of the advance of the crosslinking reaction on the free volume in a copolymer of styrene-butadiene and natural rubbers was carried out. The crosslink density developed in SBR specimens with different sulfur contents and cure temperatures was studied. SAXS technique was applied to study the process of crosslinking in NR as a function of the cure temperature. Finally, a study of different SBR/NR blends is presented using PALS and DSC.

  9. Evolution of the crosslink structure in the elastomers NR and SBR

    Science.gov (United States)

    Salgueiro, W.; Somozaa, A.; Marzocca, A. J.; Consolati, G.; Quasso, F.

    2007-02-01

    An experimental positron annihilation lifetime spectroscopy (PALS), differential scanning calorimetry (DSC) and small angle X-ray scattering (SAXS) study of the effect of the advance of the crosslinking reaction on the free volume in a copolymer of styrene-butadiene and natural rubbers was carried out. The crosslink density developed in SBR specimens with different sulfur contents and cure temperatures was studied. SAXS technique was applied to study the process of crosslinking in NR as a function of the cure temperature. Finally, a study of different SBR/NR blends is presented using PALS and DSC.

  10. Devulcanization of styrenebutadiene (SBR waste tire by controlled oxidation

    Directory of Open Access Journals (Sweden)

    Rios Rachel R.V.A.

    2006-01-01

    Full Text Available This work describes the devulcanization of vulcanized SBR (Styrene Butadiene Rubber based on controlled oxidation with nitric acid. IR, ¹H and 13C-NMR, CHN elemental analyses, TG, GPC and TPD-MS (Temperature Programmed Decomposition-Mass Spectrometry experiments suggest that nitric acid promotes two processes: (i devulcanization by oxidation of the sulfide crosslinks and (ii oxidation of the carbon framework leading to the formation of -COOH and -NO2 groups. Under aggressive conditions (HNO3, reflux the polymer chain is strongly oxidized and fragmented to a highly oxygenated low molecular weight fraction, which is soluble in water.

  11. CoV2O4: a novel anode material for lithium-ion batteries with excellent electrochemical performance.

    Science.gov (United States)

    Lu, J S; Maggay, I V B; Liu, W R

    2018-02-09

    This study reports the electrochemical applications of CoV2O4 as a novel anode for lithium-ion batteries. Ex situ analyses were performed to understand the conversion that transpires during the charge-discharge cycle. Also, the effects of different binders were analyzed. With the synergistic effect of Na-carboxymethyl cellulose and styrene butadiene rubber (CMC and SBR), a reversible capacity of 727.5 mA h g-1 was obtained after 100 cycles which indicates potential applications of CoV2O4 in energy storage devices.

  12. On the response of rubbers at high strain rates.

    Energy Technology Data Exchange (ETDEWEB)

    Niemczura, Johnathan Greenberg (University of Texas-Austin)

    2010-02-01

    In this report, we examine the propagation of tensile waves of finite deformation in rubbers through experiments and analysis. Attention is focused on the propagation of one-dimensional dispersive and shock waves in strips of latex and nitrile rubber. Tensile wave propagation experiments were conducted at high strain-rates by holding one end fixed and displacing the other end at a constant velocity. A high-speed video camera was used to monitor the motion and to determine the evolution of strain and particle velocity in the rubber strips. Analysis of the response through the theory of finite waves and quantitative matching between the experimental observations and analytical predictions was used to determine an appropriate instantaneous elastic response for the rubbers. This analysis also yields the tensile shock adiabat for rubber. Dispersive waves as well as shock waves are also observed in free-retraction experiments; these are used to quantify hysteretic effects in rubber.

  13. Biodiesel Production from Rubber Seed Oil via Esterification Process

    Directory of Open Access Journals (Sweden)

    W Widayat

    2012-07-01

    Full Text Available One promise source of alternative energy is biodiesel from rubber seed oil, because the raw materials available in plentiful quantities and can be renewed. In addition, the rubber seed is still lack of utilization, and Indonesia is one of the largest rubbers producing country in the world. The objective of this research is to studied on biodiesel production by esterification process. Parameters used in this study are the ratio of catalyst and temperature and its influence on the characteristics of the resulting biodiesel product. Characterization of rubber seed include acid content number analysis, saponification numbers, density, viscosity, iodine number, type of free fatty acids and triglyceride oils. The results of analysis showed that rubber seed oil content obtained is 50.5%. The results of the GCMS analysis showed that a free fatty acid level in rubber seed is very high. Conversion into bio-diesel oil is obtained by at most 59.91% and lowest 48.24%.

  14. Demotivating factors influencing rubber production workers

    OpenAIRE

    Mohammad Reza Iravani

    2012-01-01

    Motivation is one of the most important factors influencing workers' productivity. An increase in workers' motivation could add more value to organizations' structure and influence the profitability, significantly. In this paper, we study different factors on demotivating workers using questionnaire consist of various questions. The questionnaire is distributed among some employees who work for rubber production units located in Esfahan, Iran. The results of this survey indicate that discrimi...

  15. Mortality among rubber workers: V. processing workers.

    Science.gov (United States)

    Delzell, E; Monson, R R

    1982-07-01

    Cause-specific mortality was evaluated among 2,666 men employed in the processing division of a rubber manufacturing plant. The division was divided into two sections: front processing (compounding, mixing and milling operations) and back processing (extrusion, calendering, cement mixing and rubberized fabrics operations). Mortality rates for all processing workers combined and for men in each section were compared with rates for U.S. White males or for workers employed in other divisions of the same plant. Compared with either referent group, men in the processing division had increased mortality from leukemia, emphysema, and cancers of the stomach, large intestine, and biliary passages and liver. An excess number of deaths from stomach and larger intestine cancer was found predominantly among men in the front processing section (33 observed vs. 17.7 expected deaths, based on rates in nonprocessing workers). Increased mortality from leukemia (14 observed vs. 7.3 expected) and from emphysema (22 observed vs. 11.0 expected) was present among men employed in the back processing section. Examination of mortality from these causes according to age and the year starting work, duration of employment, and years since starting work in the relevant sections of the processing division suggested that observed excesses of stomach cancer, large intestine cancer, leukemia, and emphysema among processing workers are related to occupational exposures. These results are consistent with the findings of studies of other groups of rubber workers.

  16. Boron-Loaded Silicone Rubber Scintillators

    CERN Document Server

    Bell, Z W; Maya, L; Sloop, F V J

    2003-01-01

    Silicone rubber received attention as an alternative to polyvinyltoluene in applications in which the scintillator is exposed to high doses because of the increased resistance of the rubber to the formation of blue-absorbing color centers. Work by Bowen, et al., and Harmon, et al., demonstrated their properties under gamma/x-ray irradiation, and Bell, et al. have shown their response to thermal neutrons. This last work, however, provided an example of a silicone in which both the boron and the scintillator were contained in the rubber as solutes, a formulation which led to the precipitation of solids and sublimation of the boron component. In the present work we describe a scintillator in which the boron is chemically bonded to the siloxane and so avoids the problem of precipitation and loss of boron to sublimation. Material containing up to 18% boron, by weight, was prepared, mounted on photomultipliers, and exposed to both neutron and gamma fluxes. Pulse height spectra showing the neutron and photon respons...

  17. Design, manufacturing and testing of Controllable Rubber Trailing Edge Flaps

    DEFF Research Database (Denmark)

    Løgstrup Andersen, Tom; Aagaard Madsen, Helge; Barlas, Thanasis K

    The overall goal for the INDUFLAP project was realization of a test facility for development and test of Controllable Rubber Trailing Edge Flaps (CRTEF) for wind turbines. This report covers experimental work at DTU Wind Energy including design, manufacture and test of different configurations...... of flaps with voids in chord- or spanwise direction. Development of rubber flaps has involved further design improvements. Non-metallic spring elements and solutions for sealing of continuous extruded rubber profiles have been investigated....

  18. Vulcanization Kinetics of Natural Rubber Based On Free Sulfur Determination

    OpenAIRE

    Abu Hasan; Rochmadi Rochmadi; Hary Sulistyo; Suharto Honggokusumo

    2013-01-01

    The determination of free sulfur in the rubber vulcanizates provided significant representation of vulcanization reaction. In this research, the effects of vulcanization temperature, the mixing method of carbon black into rubber, the ingredients mixing sequence and the type of carbon black were studied on masticated and milled natural rubber in which the reaction was observed by un-reacted sulfur determination. The results showed that higher vulcanization temperature provided faster vulcaniza...

  19. Impact resistance of concrete – using slit rubber from tyres

    OpenAIRE

    Coventry, Kathryn; Richardson, Alan; Diaz, Eli

    2015-01-01

    This paper examines recycled tyre rubber, which was machine cut into slits and these were added to Portland cement concrete mixes in different percentages, based on specimen volume. They were then tested to determine the impact performance of each mix in comparison to a plain non-rubberised mix. \\ud The results indicated that concrete samples containing recycled rubber, exhibited a loss in compressive strength when compared to the plain concrete mix, however, the rubber modified samples were ...

  20. 75 FR 36472 - Goodyear Tire and Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance

    Science.gov (United States)

    2010-06-25

    ... National Highway Traffic Safety Administration Goodyear Tire and Rubber Company, Receipt of Petition for Decision of Inconsequential Noncompliance Goodyear Tire and Rubber Company, (Goodyear),\\1\\ has determined... 573, Defect and Noncompliance Responsibility and Reports. \\1\\ Goodyear Tire and Rubber Company...

  1. Magnesium affects rubber biosynthesis and particle stability in Ficus elastica, Hevea brasiliensis and Parthenium argentatum

    Science.gov (United States)

    Natural rubber biosynthesis occurs in laticifers of Ficus elastica and Hevea brasiliensis, and in parenchyma cells of Parthenium argentatum. Natural rubber is synthesized by rubber transferase using allylic pyrophosphates as initiators, isopentenyl pyrophosphate as monomeric substrate and magnesium ...

  2. Characterization of asphalt cements modified with crumbed rubber from discarded tires : final report.

    Science.gov (United States)

    1994-11-01

    The potential legislative requirement for incorporation of scrap rubber into asphalt blends mandated a thorough evaluation of the influence of scrap rubber additives on the physical properties and aging characteristics of rubber/asphalt blends. Blend...

  3. Barrierity of hydrogenated butadiene-acrylonitrile rubber and butyl rubber after exposure to organic solvents.

    Science.gov (United States)

    Krzemińska, Sylwia; Rzymski, Władysław M

    2011-01-01

    Resistance of antichemical clothing primarily depends on the type of material it is made from, in particular on the type of polymer used for coating the fabric carrier. This paper reports on systematic investigations on the influence of the cross-linking density of an elastomer and the composition of a cross-linked elastomer on its resistance to permeation of selected organic solvents. Tests of barrier material samples made from nonpolar butyl rubber (IIR) and polar hydrogenated butadiene-acrylonitrile rubber (HNBR) showed that (a) in rubber-solvent systems with medium thermodynamic affinity, cross-linking density influenced resistance to permeation and (b) the polarity of the system had a significant influence on barrierity.

  4. Elucidation of filler-to-filler and filler-to-rubber interactions in silica-reinforced natural rubber by TEM Network Visualization

    NARCIS (Netherlands)

    Sarkawi, S.S.; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2014-01-01

    Filler-to-rubber interaction is a key parameter in the reinforcement of rubber. This paper presents an investigation into filler-to-filler and filler-to-rubber interactions in silica-reinforced natural rubber (NR) in the presence and absence of a silane coupling agent. Using a special network

  5. Geotechnical Properties of Rubber Tires and Sediments Mixtures

    Directory of Open Access Journals (Sweden)

    H. Sellaf

    2014-04-01

    Full Text Available An experimental work was undertaken to study the effect of rubber tires on the geotechnical properties of a dredged sediment, using a mixing ratio of large size. For comparison, two types of soil were studied (dredged sediment from Fergoug dam and Tizi Tuff from the north west of Algeria. Taking into account the high compressibility and the low water absorption of the rubber tires, grain size analysis, density, Atterberg limits analysis, chemical composition, direct shear tests, loading-unloading tests, modified Proctor and CBR tests are performed on the two soils and their mixtures with different scrap tire rubber (10, 20, 25 and 50%. The results show that liquid limits and plastic indexes decrease with the scrap tire rubber content and that the decrease is more significant for soil with high plasticity. Cohesion also decreases with scrap tire rubber content when the internal friction angle is vacillating. Compression and recompression indexes increase gradually with the scrap tire rubber content and the variation for compression index is more significant for the two soils. Compaction characteristics and CBR values decrease with scrap tire rubber content. The CBR values for W=3% are important compared to those with W=5% excepted for mixture with (75% tuff and 25% scrap tire rubber. The results show that the scrap tire rubber can be used as a reinforcement material for dredged soil, but with a content that should not highly affect the compressibility.

  6. Analysis of residual vulcanization accelerators in baby bottle rubber teats.

    Science.gov (United States)

    Yamazaki, T; Inoue, T; Yamada, T; Tanimura, A

    1986-01-01

    An analytical method was established for the determination of dialkyldithiocarbamates (DTCs) in chloroform-acetone extracts from rubber teats for baby bottles. DTCs in the extracts were derivatized into ethyl esters and analysed by gas chromatography employing nitrogen-phosphorus detection. Dimethyldithiocarbamate and diethyldithiocarbamate were detected at levels up to 3.2 micrograms/g rubber and up to 4.6 micrograms/g rubber (as dithiocarbamic acid), respectively, in the extracts from commercially available isoprene rubber tests. DTCs can form secondary amines by acid hydrolysis, although the levels of DTCs in the extracts only made a minor contribution to the total level of measured secondary amine precursors.

  7. Industrial Hardening: 1981 Technical Status-Report.

    Science.gov (United States)

    1982-09-01

    that are sensitive to rapid shutdown would include petroleum refining and petrochemicals, rubber and plastics, and chemical and fertilizer plants. The...HEAVY-DUTY IMPACT MILLS DESCRIPTION INDUSTRIES WHERE USED Cage mills Quarries, phosphate, fertilizer , colors, presscake (e.g. vegetable oils...bauxite, rollers that operate in coke, magnesite , iron oxide pigments, conjunction with grinding sulfur, talc, graphite, calcium phosphates, rings

  8. ADAPTIVE CONTROL SYSTEM OF INDUSTRIAL REACTORS

    Directory of Open Access Journals (Sweden)

    Vyacheslav K. Mayevski

    2014-01-01

    Full Text Available This paper describes a mathematical model of an industrial chemical reactor for production of synthetic rubber. During reactor operation the model parameters vary considerably. To create a control algorithm performed transformation of mathematical model of the reactor in order to obtain a dependency that can be used to determine the model parameters are changing during reactor operation.

  9. Adhesion of nitrile rubber to UV-assisted surface chemical modified PET fabric, part II: Interfacial characterization of MDI grafted PET

    Energy Technology Data Exchange (ETDEWEB)

    Razavizadeh, Mahmoud; Jamshidi, Masoud, E-mail: mjamshidi@iust.ac.ir

    2016-08-30

    Highlights: • In this research UV-irradiated PET fabric was chemically modified. • The fabric at first carboxylated under UV irradiation using glutaric anhydride, then it was grafted using isocyanate (i.e. MDI). • The surface of the fabric was characterized before and after each treating satge. • The composite samples were prepared and tested for T-Peel test. The surfaces of the fabrics were surface characterized to understand. - Abstract: Fiber to rubber adhesion is an important subject in rubber industry. It is well known that surface treatment (i.e. physical, mechanical and chemical) is an effective method to improve interfacial bonding of fibers and/or fabrics to rubbers. UV irradiation is an effective method which has been used to increase fabric-rubber interfacial interactions. In this research UV assisted chemical modification of PET fabrics was used to increase PET to nitrile rubber (NBR) adhesion. Nitrile rubber is a perfect selection as fuel and oil resistant rubber. However it has weak bonding to PET fabric. For this purpose PET fabric was carboxylated under UV irradiation and then methylenediphenyl diisocyanate (MDI) was grafted on carboxylated PET. The chemical composition of the fabric before and after surface treatment was investigated by X-ray photoelectron spectroscopy (XPS). The sectional morphology of the experimental PET fibers and the interface between rubber compound and PET fabric was studied using scanning electron microscope (SEM). The morphology and structure of the product were analyzed by an energy dispersive X-ray spectrometer (EDX). FTIR-ATR and H NMR analysis were used to assess surface modifications on the PET irradiated fabrics.

  10. The comparison of properties and cost of material use of natural rubber and sand in manufacturing cement mortar for construction sub-base layer

    Science.gov (United States)

    Rahman, R.; Nemmang, M. S.; Hazurina, Nor; Shahidan, S.; Khairul Tajuddin Jemain, Raden; Abdullah, M. E.; Hassan, M. F.

    2017-11-01

    The main issue related to this research was to examine the feasibility of natural rubber SMR 20 in the manufacturing of cement mortar for sub-base layer construction. Subbase layers have certain functions that need to be fulfilled in order to assure strong and adequate permeability of pavement performance. In a pavement structure, sub-base is below the base and serves as the foundation for the overall pavement structure, transmitting traffic loads to the sub-grade and providing drainage. Based on this research, the natural rubber, SMR 20 was with the percentages of 0%, 5%, 10% and 15% to mix with sand in the manufacture of the cement mortar. This research describes some of the properties and cost of the materials for the natural rubber and sand in cement mortar manufacturing by laboratory testing. Effects of the natural rubber replacement on mechanical properties of mortar were investigated by laboratory testing such as compressive strength test and density. This study obtained the 5% of natural rubber replaced in sand can achieved the strength of normal mortar after 7 days and 28 days. The strength of cement mortar depends on the density of cement mortar. According to the cost of both materials, sand shows the lower cost in material for the cement mortar manufacturing than the uses of natural rubber. Thus, the convectional cement mortar which used sand need lower cost than the modified rubber cement mortar and the most economical to apply in industrial. As conclusion, the percentage of 5% natural rubber in the cement mortar would have the same with normal cement mortar in terms of the strength. However, in terms of the cost of the construction, it will increase higher than cost of normal cement mortar production. So that, this modified cement mortar is not economical for the road sub-base construction.

  11. Mapping tropical forests and deciduous rubber plantations in Hainan Island, China by integrating PALSAR 25-m and multi-temporal Landsat images

    Science.gov (United States)

    Chen, Bangqian; Li, Xiangping; Xiao, Xiangming; Zhao, Bin; Dong, Jinwei; Kou, Weili; Qin, Yuanwei; Yang, Chuan; Wu, Zhixiang; Sun, Rui; Lan, Guoyu; Xie, Guishui

    2016-08-01

    Updated and accurate maps of tropical forests and industrial plantations, like rubber plantations, are essential for understanding carbon cycle and optimal forest management practices, but existing optical-imagery-based efforts are greatly limited by frequent cloud cover. Here we explored the potential utility of integrating 25-m cloud-free Phased Array type L-band Synthetic Aperture Radar (PALSAR) mosaic product and multi-temporal Landsat images to map forests and rubber plantations in Hainan Island, China. Based on structure information detected by PALSAR and yearly maximum Normalized Difference Vegetation Index (NDVI), we first identified and mapped forests with a producer accuracy (PA) of 96% and user accuracy (UA) of 98%. The resultant forest map showed reasonable spatial and areal agreements with the optical-based forest maps of Fine Resolution Observation and Monitoring Global Land Clover (FROM-GLC) and GlobalLand30. We then extracted rubber plantations from the forest map according to their deciduous features (using minimum Land Surface Water Index, LSWI) and rapid changes in canopies during Rubber Defoliation and Foliation (RDF) period (using standard deviation of LSWI) and dense canopy in growing season (using maximum NDVI). The rubber plantation map yielded a high accuracy when validated by ground truth-based data (PA/UA > 86%) and evaluated with three farm-scale rubber plantation maps (PA/UA >88%). It is estimated that in 2010, Hainan Island had 2.11 × 106 ha of forest and 5.15 × 105 ha of rubber plantations. This study has demonstrated the potential of integrating 25-m PALSAR-based structure information, and Landsat-based spectral and phenology information for mapping tropical forests and rubber plantations.

  12. Fabrication of Wood-Rubber Composites Using Rubber Compound as a Bonding Agent Instead of Adhesives

    Directory of Open Access Journals (Sweden)

    Dongwei Shao

    2016-06-01

    Full Text Available Differing from the hot-pressing method in the manufacturing of traditional wood-rubber composites (WRCs, this study was aimed at fabricating WRCs using rubber processing to improve water resistance and mechanical properties. Three steps were used to make WRCs, namely, fiber-rubber mixing, tabletting, and the vulcanization molding process. Ninety-six WRC panels were made with wood fiber contents of 0%–50% at rotor rotational speeds of 15–45 rpm and filled coefficients of 0.55–0.75. Four regression equations, i.e., the tensile strength (Ts, elongation at break (Eb, hardness (Ha and rebound resilience (Rr as functions of fiber contents, rotational speed and filled coefficient, were derived and a nonlinear programming model were developed to obtain the optimum composite properties. Although the Ts, Eb and Rr of the panels were reduced, Ha was considerably increased by 17%–58% because of the wood fiber addition. Scanning electron microscope images indicated that fibers were well embedded in rubber matrix. The 24 h water absorption was only 1%–3%, which was much lower than commercial wood-based composites.

  13. Low surface energy rubber materials : relationship between network architecture and tack of silicone rubbers

    NARCIS (Netherlands)

    Mikrut, M.

    2007-01-01

    The objective of this work was to investigate the relationship between different factors characterizing the network structure on the tackiness of silicone rubber (PDMS). A custom tack testing device was constructed, based on the existing Tel-Tak principle. The experimental work involved testing the

  14. Natural rubber/nitrile butadiene rubber/hindered phenol composites with high-damping properties

    Directory of Open Access Journals (Sweden)

    Xiuying Zhao

    2015-10-01

    Full Text Available New natural rubber (NR/nitrile butadiene rubber (NBR/hindered phenol (AO-80 composites with high-damping properties were prepared in this study. The morphological, structural, and mechanical properties were characterized by atomic force microscopy (AFM, polarized Fourier transform infrared spectrometer (FTIR, dynamic mechanical thermal analyzer (DMTA, and a tensile tester. Each composite consisted of two phases: the NR phase and the NBR/AO-80 phase. There was partial compatibility between the NR phase and the NBR/AO-80 phase, and the NR/NBR/AO-80 (50/50/20 composite exhibited a co-continuous morphology. Strain-induced crystallization occurred in the NR phase at strains higher than 200%, and strain-induced orientation appeared in the NBR/AO-80 phase with the increase of strain from 100% to 500%. The composites had a special stress–strain behavior and mechanical properties because of the simultaneous strain-induced orientation and strain-induced crystallization. In the working temperature range of a seismic isolation bearing, the composites (especially the NR/NBR/AO-80 (50/50/20 composite presented a high loss factor, high area of loss peak (TA, and high hysteresis energy. Therefore, the NR/NBR/AO-80 rubber composites are expected to have important application as a high-performance damping material for rubber bearing.

  15. Penelitian penggunaan campuran karet alam RSS dengan stiren butadien rubber (SBR dalam pembuatan soft rubber lining

    Directory of Open Access Journals (Sweden)

    Penny Setyowati

    1995-06-01

    Full Text Available The objective of this research is to obtain optimum composition of RSS and SBR compound for making soft rubber lining compound. Based on seven combination of trials in compound formulation proved that formulation with composition of RSS 50 parts and SBR 50 parts give the best physical properties and highly cemented on steel by using “Desmodur R” adhesive solution.

  16. Kansei engineering as a tool for the design of in-vehicle rubber keypads.

    Science.gov (United States)

    Vieira, Joana; Osório, Joana Maria A; Mouta, Sandra; Delgado, Pedro; Portinha, Aníbal; Meireles, José Filipe; Santos, Jorge Almeida

    2017-05-01

    Manufacturers are currently adopting a consumer-centered philosophy which poses the challenge of developing differentiating products in a context of constant innovation and competitiveness. To merge both function and experience in a product, it is necessary to understand customers' experience when interacting with interfaces. This paper describes the use of Kansei methodology as a tool to evaluate the subjective perception of rubber keypads. Participants evaluated eleven rubber keys with different values of force, stroke and snap ratio, according to seven Kansei words ranging from "pleasantness" to "clickiness". Evaluation data was collected using the semantic differential technique and compared with data from the physical properties of the keys. Kansei proved to be a robust method to evaluate the qualitative traits of products, and a new physical parameter for the tactile feel of "clickiness" is suggested, having obtained better results than the commonly used Snap Ratio. It was possible to establish very strong relations between Kansei words and all physical properties. This approach will result in guidance to the industry for the design of in-vehicle rubber keypads with user-centered concerns. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Microstructure evolution and tribological properties of acrylonitrile-butadiene rubber surface modified by atmospheric plasma treatment

    Science.gov (United States)

    Shen, Ming-xue; Zhang, Zhao-xiang; Peng, Xu-dong; Lin, Xiu-zhou

    2017-09-01

    For the purpose of prolonging the service life for rubber sealing elements, the frictional behavior of acrylonitrile-butadiene rubber (NBR) surface by dielectric barrier discharge plasma treatments was investigated in this paper. Surface microstructure and chemical composition were measured by atomic force microscopy, field-emission scanning electron microscopy, and X-ray photoelectron spectroscopy, respectively. Water contact angles of the modified rubber surface were also measured to evaluate the correlation between surface wettability and tribological properties. The results show that plasma treatments can improve the properties of the NBR against friction and wear effectively, the surface microstructure and roughness of plasma-modified NBR surface had an important influence on the surface tribological behavior, and the wear depth first decreased and then increased along with the change of plasma treatment time. It was found that the wettability of the modified surface was gradually improved, which was mainly due to the change of the chemical composition after the treatment. This study suggests that the plasma treatment could effectively improve the tribological properties of the NBR surface, and also provides information for developing wear-resistant NBR for industrial applications.

  18. Viscoelastic properties of short aramid fibres-reinforced rubbers

    NARCIS (Netherlands)

    Sadatshirazi, S.; Talma, Auke; Noordermeer, Jacobus W.M.

    2013-01-01

    Among short fiber-reinforced composites, those with rubber matrices have gained great importance due to the advantages they have in processing and low cost, coupled with high strength. These composites combine the elastic behavior of rubbers with strength and stiffness of fibers. Reinforcement with

  19. Evaluation of phosphorus status of some soils under estate rubber ...

    African Journals Online (AJOL)

    Evaluation of phosphorus status of some soils under estate rubber (Hevea Brasiliensis Muel. Agro.) trees in Southern Cross River State. EE Attoe, UC Amalu. Abstract. No abstract. Keywords: rubber tree; phosphorus uptake; soil P; leaf P; root mat P Global Journal of Agricultural Sciences Vol. 4(1) 2005: 55-61. Full Text:.

  20. 21 CFR 872.6300 - Rubber dam and accessories.

    Science.gov (United States)

    2010-04-01

    ...) MEDICAL DEVICES DENTAL DEVICES Miscellaneous Devices § 872.6300 Rubber dam and accessories. (a) Identification. A rubber dam and accessories is a device composed of a thin sheet of latex with a hole in the... cavity preparation. The device is stretched around a tooth by inserting a tooth through a hole in the...

  1. Electric pulse resistance of liquid nitrogen and rubber

    Science.gov (United States)

    Kurets, V. I.; Tarakanovskii, É. N.; Filatov, G. P.

    1995-05-01

    We report the results of experimental investigations of the breakdown amplitudes of pulsed voltages applied to centimeter-thick layers of liquid nitrogen and various kinds of rubber at 77 K. We report the characteristics of pulses that will puncture rubber in liquid nitrogen.

  2. Profitability Analysis Of Natural Rubber Tapping In Southern Nigeria ...

    African Journals Online (AJOL)

    The study was a conducted to analyse cost and returns to rubber tapping in Southern Nigeria .Structured questionnaires were administered to a random sample of 129 tappers . Data collected were analysed using descriptive statistics and budgetary technique. The result indicated that males dominated rubber tapping, all of ...

  3. Effects of Dietary Substitution of Rubber Seed Cake for Groundnut ...

    African Journals Online (AJOL)

    Three hundred (300) five weeks old, Anak broilers were used in a 4-week experiment to determine the effect of dietary substitution of rubber seed cake for groundnut cake on the performance of broilers at the finisher phase. Graded levels of rubber seed cake (0, 25, 50, 75 and 100%) substituted corresponding levels of ...

  4. Replacement of groundnut cake with rubber ( Hevea brasiliensis ...

    African Journals Online (AJOL)

    This study was carried out to determine the level of rubber seed cake (RSC) that could be used to replace groundnut cake (GNC) in practical diets of Oreochromis niloticus. RSC, a by-product of the oil extraction of the rubber tree seed and GNC were interchangeably replaced in the formulation of five experimental diets fed ...

  5. Constraints to rubber production in Sapele local government area of ...

    African Journals Online (AJOL)

    The study investigated among other things the constraints to rubber production in Sapele Local Government Area of Delta State, Nigeria. One hundred and twenty rubber farmers randomly selected from twelve villages in the Local Government Area were used to constitute the sample. Stratified and random sampling was ...

  6. Adaptation of the rubber bandage for safe use as tourniquet ...

    African Journals Online (AJOL)

    The safety of the pneumatic tourniquet lies in the fact that the pressure generated beneath it can be determined and is reproducible unlike the rubber bandage tourniquet with subjective and irreproducible tissue pressure. Application of the rubber bandage over the cuff of an aneroid sphygmomanometer enabled direct ...

  7. Differential responses of two rubber tree clones to chilling stress ...

    African Journals Online (AJOL)

    Chilling stress is one of the most important environmental factors that limit the growth, distribution and yield of rubber tree in China. The effects of chilling stress on the grated plants of two rubber trees clones, GT1 and Wenchang217, were studied by physiological methods in controlled light chamber in order to explore the ...

  8. Influence of Plasma Treatments on the Frictional Performance of Rubbers

    NARCIS (Netherlands)

    Wolthuizen, D.J.; Martinez-Martinez, D.; Pei, Y.T.; Hosson, J.Th.M. De

    The frictional performance of several rubbers after pulsed-DC plasma treatments has been examined. In all cases, the treated rubbers showed better performance than the corresponding untreated ones. Stronger treatments, in terms of longer process time and/or higher substrate bias voltage, led to

  9. Natural Rubber Quantification in Sunflower Using an Automated Solvent Extractor

    Science.gov (United States)

    Leaves of sunflower (Helianthus annuus) produce a small amount of low molecular weight natural rubber (NR) and this species has potential as a rubber-producing crop plant. Quantifying NR in plant tissue has traditionally been accomplished using Soxhlet or gravimetric methodologies. Accelerated solve...

  10. Ground tire rubber as a stabilizer for subgrade soils : [summary].

    Science.gov (United States)

    2014-05-01

    Over 250 million scrap tires are generated : annually in the U.S. Historically, a significant : portion of these tires have been processed into : finely ground tire rubber (GTR), or crumb rubber, : for use as an additive in hot mix asphalt (HMA) : pa...

  11. Ground tire rubber as a stabilizer for subgrade soils.

    Science.gov (United States)

    2014-05-01

    Over 250 million scrap tires are generated annually in the U.S. Historically, a significant portion of these tires : have been processed into finely ground tire rubber (GTR), or crumb rubber, for use as an additive in hot mix asphalt : (HMA) pavement...

  12. Research and Application Progress of Silicone Rubber Materials in Aviation

    Directory of Open Access Journals (Sweden)

    HUANG Yanhua

    2016-06-01

    Full Text Available The research progress of heat resistance, cold resistance, electrical conductivity and damping properties of aviation silicone rubber were reviewed in this article. The heat resistance properties of silicone rubber can be enhanced by changing the molecular structure (main chain, end-group, side chain and molecular weight of the gum and adding special heat-resistance filler. The cold resistance of aviation silicone rubber can be enhanced by adjusting the side chain molecular structure of the gum and the content of different gum chain. The electrical conductivity of silicone rubber can be improved by optimizing, blending and dispersing of conductive particles. The damping property of silicone rubber can be improved by designing and synthesizing of high-molecular polysiloxane damping agent. Furthermore, the application of aviation silicone rubber used in high-low temperature seal, electrical conduction and vibration damping technology are also summarized, and the high performance (for example long-term high temperature resistance, ultralow temperature resistance, high electromagnetic shelding, long-term fatigue resistance vibration damping, quasi constant modulus and so on of special silicone rubber is the future direction of aviation silicone rubber.

  13. Rubber composites cured with sulphur and peroxide and ...

    Indian Academy of Sciences (India)

    Besides classical applications of rubber products in tyres, conveyer belts and other products from technical rubber, ... application of sulphur curing systems leads to the forming of sulphidic bridges with various number of ... have advantages but also drawbacks, the main aim was to suppress the main negatives of both curing ...

  14. Guayule resin detection and influence on guayule rubber

    Science.gov (United States)

    Guayule (Parthenium argentatum) is a natural rubber (cis-1,4-polyisoprene) producing crop, native to North America. Guayule also produces organic resins, complex mixtures of terpenes, triglycerides, guayulins, triterpenoids and other components. During natural rubber extraction, guayule resins can b...

  15. Reinforcement Effect of Corn Flour in Rubber Composites

    Science.gov (United States)

    Corn flour is an economical renewable material and investigated in this study as filler for rubber composites. The composites were prepared by mixing an aqueous dispersion of corn flour with rubber latex, followed by freeze-drying and compression molding. The small strain elastic modulus and the str...

  16. Rubber Flooring Impact on Production and Herdlife of Dairy Cows

    Science.gov (United States)

    Use of rubber flooring in dairies has become popular because of perceived cow comfort. The overall objective of this longitudinal study was to evaluate production, reproduction, and retention of first and second lactations of cows assigned to either rubber (RUB) or concrete (CON) flooring at the fe...

  17. Polyacrylamide brush coatings preventing microbial adhesion to silicone rubber

    NARCIS (Netherlands)

    Fundeanu, Irina; van der Mei, Henny C.; Schouten, Arend J.; Busscher, Henk J.

    2008-01-01

    Silicone rubber is a frequently used biomaterial in biomedical devices and implants, yet highly prone to microbial adhesion and the development of a biomaterial-centered infection. Effective coating of silicone rubber to discourage microbial adhesion has thus far been impossible due to the

  18. Screening ten genotypes of natural rubber seedlings ( Hevea ...

    African Journals Online (AJOL)

    A field study was conducted in 2012 and 2013 cropping season at the Research Farm of National Root Crops Research Institute, (NRCRI) Umudike, in Abia State, to screen 10 rubber genotypes collected from Rubber Research Institute of Nigeria for tolerant to drought conditions. The aim was to select tolerant genotypes for ...

  19. Page 1 UTILISATION OF RUBBER SEED OL IN THE ...

    African Journals Online (AJOL)

    POLYVINYL CHLORIDE AGAINST THERMAL DEGRADATION. F.E. Okieimen. Department of Chemistry, University of Benin, Benin City, Nigeria. ABSTRACT. Thermal degradation studies on polyvinyl chloride in the presence of rubber seed oil, epoxidized rubber seed oil and metal soaps (barium, cadmium and lead) of the ...

  20. Blends of guayule natural rubber latex with commercial latex polymers

    Science.gov (United States)

    Guayule (Parthenium argentatum) is a woody desert shrub that produces natural rubber, cis-1,4 polyisoprene, by biosynthesis. It is currently cultivated in the southwestern United States as a source of latex and rubber for commercial development. Guayule latex is similar to Hevea latex in polymer mo...

  1. Implication of Climate Variability for Latex Exudates F Rubber Tree ...

    African Journals Online (AJOL)

    The study aimed at: assessing the relationship between latex exudates and climate variability; identifying the most critical climate element(s) in the yield variability of rubber; and examining the predictability of rubber yield based on climate variability. Fifteen years data was collected from documented, but unpublished, ...

  2. Reinforcement of latex rubber by the incorporation of amphiphilic particles

    Science.gov (United States)

    Latex rubbers are fabricated from latex suspensions. During the fabrication process, latex particles are bound together while water is removed from the suspension. This report shows that the mechanical properties of latex rubbers can be improved by incorporating a small amount of amphiphilic submicr...

  3. minimum variance estimation of yield parameters of rubber tree

    African Journals Online (AJOL)

    2013-03-01

    Mar 1, 2013 ... raw material supply chain and hence marketing plan. The result matches the wet and dry spell of southern. Nigeria and its effect on rubber tree latex production. The seasonal value by quarter is estimated for each clone to be used for appropriate quarterly adjustment in the aggregate rubber production ...

  4. Characterization of weed flora in rubber trees plantations of Bongo ...

    African Journals Online (AJOL)

    Objectives: the main objective of this study is to characterize the weed floristic diversity of the Bongo rubber trees plantation and to provide a map for sustainable weed management. Methodology and results: a floristic survey of the Para rubber plantations of Bongo (Southeast Côte d'Ivoire) was conducted in 2007 and early ...

  5. Demotivating factors influencing rubber production workers

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Iravani

    2012-01-01

    Full Text Available Motivation is one of the most important factors influencing workers' productivity. An increase in workers' motivation could add more value to organizations' structure and influence the profitability, significantly. In this paper, we study different factors on demotivating workers using questionnaire consist of various questions. The questionnaire is distributed among some employees who work for rubber production units located in Esfahan, Iran. The results of this survey indicate that discrimination on annual job compensation, entrusting responsibilities and unpleasant relationship with family partner are some of the most important factors influencing employees' motivation. While financial factors play important role on increasing employees' motivation, non-financial factors are considered more important.

  6. Hacking Experiment Using USB Rubber Ducky Scripting

    Directory of Open Access Journals (Sweden)

    Benjamin Cannoles

    2017-04-01

    Full Text Available By leaving your computer unlocked while you are away for seconds can give hackers all the time they need to obtain your personal information from your computer. This paper aims to detail the necessary research and development of a USB Rubber Ducky script, to obtain clear text logon id and passwords from a Windows machine, in mere seconds. Each stage is laid out in sections discussing Ducky script, powershell, Mimikatz, and reenabling the vulnerability by breaking down the attack into two parts for Windows 7 and up operating systems.

  7. Viscoelastic modeling of filled, crosslinked rubbers

    Science.gov (United States)

    Joshi, Prashant G.

    1999-10-01

    Filled polymer systems have been a subject of interest for rheologists since the past many decades. Their applications range from paints and pigments to high performance composite materials. Tires come under a special class of applications wherein the type of filler used, its reinforcing abilities, traction improvement capabilities and cost effectiveness enormously control the final end use. Presently, there is lack of a complete understanding of the behavior of these materials under different load conditions. Moreover there is a lack of a comprehensive theory which can describe the rheology of filled rubbers, their chemorheology, and their behavior in the final fully cured state simultaneously. The present work is aimed at capturing a wide range of rheological/viscoelastic properties of filled rubbers with one set of constitutive/kinetic equations and a flexible relaxation spectrum. Various mechanical properties of filled, crosslinked rubbers were investigated in order to understand their analogy in the melt state. For this purpose, quasi-static hysteresis and step-strain relaxation experiments were carried out. Dynamic mechanical properties were understood in great details by using Fourier harmonic analysis to understand the time and strain non-linearities in the material. The time non-linearities arise due to thixotropic and non-isothermal effects, while the waveform distortions (strain related) occur due to non-linear viscoelastic effects. It is also very important to ensure no interference from any extraneous noise in the system during a dynamic test. Using the experimental evidences in melt rheology (creeping flow, shear start-up, and relaxation), and the kinetic mechanisms that affect chemorheology [152], an appropriate thixotropic-viscoelastic spectrum was chosen in order to describe experiments in all states of SBR rubber satisfactorily. This approach convinces that various manifestations of the filler in the melt state are preserved during crosslinking

  8. A Micro-Mechanically Based Continuum Model for Strain-Induced Crystallization in Natural Rubber

    Science.gov (United States)

    Mistry, Sunny Jigger

    Recent experimental results show that strain-induced crystallization can substantially improve the crack growth resistance of natural rubber. While this might suggest superior designs of tires or other industrial applications where elastomers are used, a more thorough understanding of the underlying physics of strain-induced crystallization in natural rubber has to be developed before any design process can be started. The objective of this work is to develop a computationally-accessible micro-mechanically based continuum model, which is able to predict the macroscopic behavior of strain crystallizing natural rubber. While several researchers have developed micro-mechanical models of partially crystallized polymer chains, their results mainly give qualitative agreement with experimental data due to a lack of good micro-macro transition theories or the lack of computational power. However, recent developments in multiscale modeling in polymers provide new tools to continue this early work. In this thesis, a new model is proposed to model strain-induced crystallization in natural rubber. To this end, a micro-mechanical model of a constrained partially crystallized polymer chain with an extended-chain crystal is derived and connected to the macroscopic level using the non-affine micro-sphere model. On the macroscopic level, a thermodynamically consistent framework for strain-crystallizing materials is developed, and a description of the crystallization kinetics is introduced. For that matter, an evolution law for crystallization based on the gradient of the macroscopic Helmholtz free energy function (chemical potential) in combination with a simple threshold function is used. A numerical implementation of the model is proposed and its predictive performance assessed using published data.

  9. New type of liquid rubber and compositions based on it.

    Science.gov (United States)

    Semikolenov, S V; Nartova, A V; Voronchikhin, V D; Dubkov, K A

    2014-11-01

    The new method for producing the functionalized polymers and oligomers containing carbonyl C=O groups is developed. The method is based on the noncatalytic oxidation of unsaturated rubbers by nitrous oxide (N2O) at 180-230 °С. The proposed method allows obtaining the new type of functionalized rubbers-liquid unsaturated polyketones with regulated molecular weight and concentration of C=O groups. The influence of the liquid polyketone addition on properties of rubber-based composites is investigated. The study indicates good prospects of using the liquid polyketones for the improvement of properties and operating characteristics of the various types of rubbers and the rubber-cord systems.

  10. Statistical Discrimination of Latex between Healthy and White Root Infected Rubber Tree based on Dry Rubber Content

    Science.gov (United States)

    Suhaimi Sulaiman, Mohd; Hashim, Hadzli; Faiz Mohd Sampian, Ahmad; Korlina Madzhi, Nina; Faris Mohd Azmi, Azrie; Aishah Khairuzzaman, Noor; Aima Ismail, Faridatul

    2015-11-01

    Dry rubber content (DRC) is one of main material existing inside latex. It is usually in ranged of 25% - 45% of rubber latex. Statistical analysis are done to determine the discrimination of dry rubber content of latex between healthy and white root infected rubber tree. Based on 150 rubber trees and 10 clones tested, parametric test which include normality test, error-bar plot, and paired samples test are done. The result outcomes have shown that both data of dry rubber content of latex for healthy and white root infected rubber tree are normally distributed. Error-bar plot test is clearly indicated that there is visible discrimination between both cases. Paired samples test are done to reinforce this findings in terms of numerical p- value which is found to be less than 0.05. Thus, this indicate overwhelming evidence that healthy group can be discriminated from white root. Conclusively, changes in DRC content in latex can be correlated with white root disease infections of rubber tree.

  11. [Mites (Acari) from rubber trees (Hevea brasiliensis Muell. Arg., Euphorbiaceae) and spontaneous euphorbiaceous in rubber trees cultivation].

    Science.gov (United States)

    Bellini, Marcos R; Feres, Reinaldo J F; Buosi, Renato

    2008-01-01

    Quarterly samples were done in 2001 on three rubber tree plantation in the northwest of the state of São Paulo. Three rubber trees of each locality were sampled. Between the rows of rubber tree four species of spontaneous euphorbiaceous were collected: Chamaesyce hirta, C. hyssopifolia, Euphorbia heterophylla and Phyllanthus tenellus. A total of 8.954 mites of 38 species, belonging to 31 genera of 11 families were collected. Tydeidae and Phytoseiidae had the highest diversity of species, 9 and 7, respectively. The most abundant families were Eriophyidae (3.594), Tydeidae (2.825) and Tenuipalpidae (1.027). The most abundant species on the rubber trees were: phytophagous - Calacarus heveae Feres, Tenuipalpus heveae Baker, Lorryia sp.2, Lorryia formosa Cooreman and Lorryia sp.1; predators - Zetzellia quasagistemas Hernandes & Feres, Pronematus sp., Iphiseiodes zuluagai Denmark & Muma and Euseius citrifolius Denmark & Muma. Among the spontaneous euphorbiaceous, predatory mites were abundantly found on C. hirta and E. heterophylla, mainly Pronematus sp. and E. citrifolius, suggesting that these plants could be important in the maintenance of these predators in the rubber tree cultivation areas. However, plants that can shelter predators and at the same time exert strong competition (nutrients, water etc) to rubber trees, can not be recommended for pest management programs. Studies about competition between rubber trees and spontaneous plants need to be conducted for feasible efficient programs of environmental management, aiming at the control of pest mites of rubber tree.

  12. Nylon-6/rubber blends: 6. Notched tensile impact testing of nylon-6(ethylene-propylene rubber) blends

    NARCIS (Netherlands)

    Dijkstra, Krijn; Dijkstra, K.; ter Laak, J.A.; ter Laak, J.; Gaymans, R.J.

    1994-01-01

    The deformation and fracture behaviour of nylon-6/EPR (ethylene-propylene rubber) blends is studied as a function of strain rate and rubber content. Therefore, tensile experiments are conducted on notched specimens over a broad range of draw speeds (including strain rates as encountered in normal

  13. Reinforcing effect of plasma modified halloysite nanotubes in a carbon black filled natural rubber-butadien rubber matrix

    NARCIS (Netherlands)

    Poikelispaa, Minna; Das, Amit; Dierkes, Wilma K.; Vuorinen, Jyrki

    2011-01-01

    Rubber composites are generally produced by the direct incorporation of fillers like carbon black and/or silica into the rubber matrix. The incorporation of different types of nanofillers is the subject of recent research with the aim of preparing composites with special compositions and properties.

  14. Recycling of rubber tires in electric arc furnace steelmaking: simultaneous combustion of metallurgical coke and rubber tyres blends

    Energy Technology Data Exchange (ETDEWEB)

    Magdalena Zaharia; Veena Sahajwalla; Byong-Chul Kim; Rita Khanna; N. Saha-Chaudhury; Paul O' Kane; Jonathan Dicker; Catherine Skidmore; David Knights [University of New South Wales, Sydney, NSW (Australia). School of Materials Science and Engineering

    2009-05-15

    The present study investigates the effect of addition of waste rubber tires on the combustion behavior of its blends with coke for carbon injection in electric arc furnace steelmaking. Waste rubber tires were mixed in different proportions with metallurgical coke (MC) (10:90, 20:80, 30:70) for combustion and pyrolysis at 1473 K in a drop tube furnace (DTF) and thermogravimetric analyzer (TGA), respectively. Under experimental conditions most of the rubber blends indicated higher combustion efficiencies compared to those of the constituent coke. In the early stage of combustion the weight loss rate of the blends is much faster compared to that of the raw coke due to the higher volatile yield of rubber. The presence of rubber in the blends may have had an impact upon the structure during the release and combustion of their high volatile matter (VM) and hence increased char burnout. Measurements of micropore surface area and bulk density of the chars collected after combustion support the higher combustion efficiency of the blends in comparison to coke alone. The surface morphology of the 30% rubber blend revealed pores in the residual char that might be attributed to volatile evolution during high temperature reaction in oxygen atmosphere. Physical properties and VM appear to have a major effect upon the measured combustion efficiency of rubber blends. The study demonstrates that waste rubber tires can be successfully co-injected with metallurgical coke in electric arc furnace steelmaking process to provide additional energy from combustion. 44 refs., 11 figs., 2 tabs.

  15. Accelerated lifetime test of vibration isolator made of Metal Rubber material

    Science.gov (United States)

    Ao, Hongrui; Ma, Yong; Wang, Xianbiao; Chen, Jianye; Jiang, Hongyuan

    2017-01-01

    The Metal Rubber material (MR) is a kind of material with nonlinear damping characteristics for its application in the field of aerospace, petrochemical industry and so on. The study on the lifetime of MR material is impendent to its application in engineering. Based on the dynamic characteristic of MR, the accelerated lifetime experiments of vibration isolators made of MR working under random vibration load were conducted. The effects of structural parameters of MR components on the lifetime of isolators were studied and modelled with the fitting curves of degradation data. The lifetime prediction methods were proposed based on the models.

  16. Factors Affecting the Adsorption of Trivalent Chromium Ions by Activated Carbon Prepared from Waste Rubber Tyres

    Directory of Open Access Journals (Sweden)

    Sylvia E. Benjamin

    2017-08-01

    Full Text Available Economic gains are generally the outcome of industrialization and consequently urbanization. However, positive fiscal index generates a negative impact on natural environment sources heaving pollutant burden on soil, air and water. Industries throw tones of contaminated water into soil and water bodies without proper treatment and create a potential threat for both living and non-living species. Chromium in trivalent state (Cr3+ is added in water bodies and soil through waste water from tanneries, cooling water systems, chemical and pulp and paper industries. The present research work aims at the preparation of an inexpensive activated carbon prepared from non- degradable waste scrap rubber tyres. The carbon produced from scrap rubber tyres was activated by 5% solution of BaCl2 and 0.4 N solution of HCl and verified by ethylene blue solution. The adsorption capacity of the Tyre activated carbon (TAC was investigated for different parameters i.e., initial chromium (III ion concentration, activated carbon dosage, contact/ stirring time and pH. The adsorption capacity of TAC depends on the initial metal ion concentration and the TAC dose. pH of the chromium solution effects the adsorption capacity of TAC due to the formation of tetra hydroxochromate(III complexes,. The results show that TAC offers a cost effective reclamation process for the removal of Cr3+ from effluent waters.

  17. Multiscale physics of rubber-ice friction

    Science.gov (United States)

    Tuononen, Ari J.; Kriston, András; Persson, Bo

    2016-09-01

    Ice friction plays an important role in many engineering applications, e.g., tires on icy roads, ice breaker ship motion, or winter sports equipment. Although numerous experiments have already been performed to understand the effect of various conditions on ice friction, to reveal the fundamental frictional mechanisms is still a challenging task. This study uses in situ white light interferometry to analyze ice surface topography during linear friction testing with a rubber slider. The method helps to provide an understanding of the link between changes in the surface topography and the friction coefficient through direct visualization and quantitative measurement of the morphologies of the ice surface at different length scales. Besides surface polishing and scratching, it was found that ice melts locally even after one sweep showing the refrozen droplets. A multi-scale rubber friction theory was also applied to study the contribution of viscoelasticity to the total friction coefficient, which showed a significant level with respect to the smoothness of the ice; furthermore, the theory also confirmed the possibility of local ice melting.

  18. Synthesis biolubricant from rubber seed oil

    Science.gov (United States)

    Hung, Nguyen Tran Dong; Tuyen, Dang Thi Hong; Viet, Tran Tan

    2017-09-01

    The objective was biolubricant preparation from rubber seed oil (RSO) using polymerization reactor with/without catalyst in batch reactor. Before become reactant in polymerization reaction, a non-edible rubber seed oil was converted into methyl ester by esterification/tranesterification reaction with methanol and acid/base catalyst. The polymerization reaction parameters investigated were reaction time, temperature and weight ratio (catalyst with feed), and their effect on the bio lubricant formation. The result show significant conversion of methyl ester to bio lubricant in the temperature reaction of 160°C, reaction time of 2h min and ratio of super acid catalyst (tetrafluoroboric acid-sHBF4) of 3 %w/w. The resulting products were confirmed by GC-MS, FTIR spectroscopy and also analyzed for the viscosity. The best viscosity value of RSOFAME polymer was 110.6 cSt when the condition polymerization reaction were 160 °C, reaction time 3h, 6 wt% mass ratio of oil:catalyst.

  19. Evaluation of the modified nanoclay effect on the vulcanization of SBR through rheometric curve and DSC;Avaliacao do efeito de nanoargila modificada na vulcanizacao de SBR atraves da curva reometrica e DSC

    Energy Technology Data Exchange (ETDEWEB)

    Forte, Maria Madalena C.; Brito, Karin J.S., E-mail: mmcforte@ufrgs.b [Universidade Federal do Rio Grande do Sul (PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica; Gheller Junior, Jordao [SENAI, Sao Leopoldo, RS (Brazil). Centro Tecnologico de Polimeros

    2009-07-01

    Rubber nanocomposites with nanoclays organically modified by quaternary ammonium salts may have the curing features modified significantly, since the salts may act on the rubber cure system. The aim of this work is to evaluate the influences of an organically modified montmorillonite (OMMT) on the curing reaction of an SBR (styrene butadiene rubber) with sulfur. The SBR/OMMT nanocomposites were prepared by co-coagulating SBR latex and Cloisite{sup R} 20A aqueous suspension at different nanoclay concentrations. The OMMT effect on the sulfur curing reaction was evaluated by the rheometric curve using a rheometer type RPA (Rubber Process Analyzer) and the heat of vulcanization (DELTAH{sub v}) using Differential Scanning Calorimetry (DSC). The evaluation of the clay nanolayers dispersion in the SBR matrix was accomplished by x-ray diffraction (XRD) analysis. (author)

  20. Penelitian pengaruh variasi bahan pelunak naphtenic oil terhadap sifat fisis tegangan putus dan perpanjangan putus kompon karet untuk alas sapi

    Directory of Open Access Journals (Sweden)

    Luciawati Sunarjo

    1996-12-01

    Full Text Available The aim of this research is to know influence of plasticizer naphtenic oil to the physical properties of tensile strength and elongation at break of rubber compound for cowmats. It makes from Rubber Smoke Sheet (RSS and Styrene Butadiene Rubber 1502 (SBR as raw material with addition ingredients are Calcium Carbonate, FEF black, Stearic Acid, Zinc Oxide, Plasticizer Naphtenic Oil, Paraffine Wax, TMT, CBS, AOSP and Sulphur as Vulcanizing agent. Rubber compound for cowmats, formed to slab by hydraulic press at 1500C and 150 Kg/cm2. Than tested tensile strength and elongation at break. The result of this research indicated that platicizer naphtenic oil (x and tensile strength have regression equation as Y1 = 24.168 – 0.634 X (r = 0.87, while naphtenic oil and elongation at break have regression equation as Y2 = 236.32 + 21 X (r = 0.88.

  1. Progress in Characterizing Thermal Degradation of Ethylene-Propylene Rubber

    Energy Technology Data Exchange (ETDEWEB)

    Fifield, Leonard S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Huang, Qian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Childers, Matthew I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Correa, Miguel [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shin, Yongsoon [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zwoster, Andy [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-08-26

    Ethylene-propylene rubber (EPR) is one of the two most common nuclear cable insulation materials. A large fraction of EPR-insulated cables in use in the nuclear industry were manufactured by The Okonite Company. Okoguard® is the name of the medium voltage thermoset EPR manufactured by The Okonite Company. Okoguard® has been produced with silane-treated clay filler and the characteristic pink color since the 1970’s. EPR is complex material that undergoes simultaneous reactions during thermal aging including oxidative and thermal cleavage and oxidative and thermal crosslinking. This reaction complexity makes precise EPR service life prediction from accelerated aging using approaches designed for single discreet reactions such as the Arrhenius approach problematic. Performance data and activation energies for EPR aged at conditions closer to service conditions will improve EPR lifetime prediction. In this report pink Okoguard® EPR insulation material has been thermally aged at elevated temperatures. A variety of characterization techniques have been employed to track material changes with aging. It was noted that EPR aged significant departure in aging behavior seemed to occur at accelerated aging temperatures between 140°C and 150°C at around 20 days of exposure. This may be due to alternative degradation mechanisms being accessed at this higher temperature and reinforces the need to perform accelerated aging for Okoguard® EPR service life prediction at temperatures below 150°C.

  2. 40 CFR 428.30 - Applicability; description of the solution crumb rubber subcategory.

    Science.gov (United States)

    2010-07-01

    ... solution crumb rubber subcategory. 428.30 Section 428.30 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS RUBBER MANUFACTURING POINT SOURCE CATEGORY Solution Crumb Rubber Subcategory § 428.30 Applicability; description of the solution crumb rubber subcategory...

  3. 40 CFR 428.20 - Applicability; description of the emulsion crumb rubber subcategory.

    Science.gov (United States)

    2010-07-01

    ... emulsion crumb rubber subcategory. 428.20 Section 428.20 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS RUBBER MANUFACTURING POINT SOURCE CATEGORY Emulsion Crumb Rubber Subcategory § 428.20 Applicability; description of the emulsion crumb rubber subcategory...

  4. 21 CFR 177.1480 - Nitrile rubber modified acrylonitrile-methyl acrylate copolymers.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Nitrile rubber modified acrylonitrile-methyl... Nitrile rubber modified acrylonitrile-methyl acrylate copolymers. Nitrile rubber modified acrylonitrile... rubber modified acrylonitrile-methyl acrylate copolymers consist of basic copolymers produced by the...

  5. 75 FR 51981 - Polychloroprene Rubber from Japan: Final Results of Sunset Review and Revocation of Finding

    Science.gov (United States)

    2010-08-24

    ... International Trade Administration Polychloroprene Rubber from Japan: Final Results of Sunset Review and... review of the antidumping finding on polychloroprene rubber from Japan. Because the domestic interested... polychloroprene rubber from Japan. See Polychloroprene Rubber from Japan, 38 FR 33593 (December 6, 1973). On...

  6. 21 CFR 801.437 - User labeling for devices that contain natural rubber.

    Science.gov (United States)

    2010-04-01

    ... rubber. 801.437 Section 801.437 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND... User labeling for devices that contain natural rubber. (a) Data in the Medical Device Reporting System..., natural rubber that contacts humans. The term “natural rubber” includes natural rubber latex, dry natural...

  7. 40 CFR 428.40 - Applicability; description of the latex rubber subcategory.

    Science.gov (United States)

    2010-07-01

    ... latex rubber subcategory. 428.40 Section 428.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS RUBBER MANUFACTURING POINT SOURCE CATEGORY Latex Rubber Subcategory § 428.40 Applicability; description of the latex rubber subcategory. The provisions of...

  8. Plant and bird diversity in rubber agroforests in the lowlands of Sumatra, Indonesia

    NARCIS (Netherlands)

    Beukema, Hendrien; Danielsen, Finn; Vincent, Gregoire; Hardiwinoto, Suryo; van Andel, Jelte

    Plant and bird diversity in the Indonesian jungle rubber agroforestry system was compared to that in primary forest and rubber plantations by integrating new and existing data from a lowland rain forest area in Sumatra. Jungle rubber gardens are low-input rubber (Hevea brasiliensis) agroforests that

  9. Reinforcement effect of soy protein nanoparticles in amine-modified natural rubber latex

    Science.gov (United States)

    Mechanical properties of natural rubber reinforced with soy protein nanoparticles are useful for various rubber applications. However, the properties is further improved by improving interactions between soy protein and rubber. A novel method is used to modify particle surface of natural rubber late...

  10. Practical application of thermoreversibly Cross-linked rubber products

    Science.gov (United States)

    Polgar, L. M.; Picchioni, F.; de Ruiter, E.; van Duin, M.

    2017-07-01

    Currently, rubber products cannot simply be reprocessed after their product life, due to the irreversible cross-linking methods traditionally applied. The purpose of this work is to investigate how thermoreversible cross-linking of rubbers via Diels Alder chemistry can be used for the development of recyclable rubber products. Unfortunately, the applicability of the thermoreversible EPM-g-furan/BM system appears to be limited to room temperature applications, because of the rapid deterioration of the compression set at elevated temperatures compared to irreversibly cross-linked EPM. However, the use of EPM rubber modified with thiophene or cyclopentadiene moieties may extend the temperature application range and results in rubber products with acceptable properties. Finally, rubber products generally comprise fillers such as silica, carbon black or fibers. In this context, the reinforcing effect of short cut aramid fibers on the material properties of the newly developed thermoreversibly cross-linked EPM rubbers was also studied. The material properties of the resulting products were found to be comparable to those of a fiber reinforced, peroxide cured reference sample.

  11. The optimum content of rubber ash in concrete: flexural strength

    Science.gov (United States)

    Senin, M. S.; Shahidan, S.; Shamsuddin, S. M.; Ariffin, S. F. A.; Othman, N. H.; Rahman, R.; Khalid, F. S.; Nazri, F. M.

    2017-11-01

    Discarded scrap tyres have become one of the major environmental problems nowadays. Several studies have been carried out to reuse waste tires as an additive or sand replacement in concrete with appropriate percentages of tire rubber, called as rubberized concrete to solve this problem. The main objectives of this study are to investigate the flexural strength performance of concrete when adding the rubber ash and also to analyse the optimum content of rubber ash in concrete prisms. The performance total of 30 number of concrete prisms in size of 100mm x 100mm x 500 mm were investigated, by partially replacement of rubber ash with percentage of 0%, 3%, 5%, 7% and 9% from the volume of the sand. The flexural strength is increased when percentage of rubber ash is added 3% from control concrete prism, RA 0 for both concrete prism age, 7 days and 28 days with value 1.21% and 0.976% respectively. However, for RA 5, RA 7 and RA 9, the flexural strength was decreased compared to the control for both age, 7 days and 28 days. In conclusion, 3% is the optimum content of rubber ash in concrete prism for both concrete age

  12. Fabrication of shape memory natural rubber using palmitic acid

    Directory of Open Access Journals (Sweden)

    Jeff Sze-Hua Wee

    2017-10-01

    Full Text Available This paper investigates the practicability of fabricating a shape memory natural rubber with the use of palmitic acid as the swelling agent. Strips of natural rubber samples were swollen in molten palmitic acid at 75 °C. Equilibrium swelling of natural rubber with palmitic acid was found to occur at approximately 50 min of swelling time. Under cooling effect, the palmitic acid crystallized to form a percolated crystalline platelet network. These networks allow fabricated shape memory natural rubber (SMNR to deform and recover its shape at a temperature above the melting point of palmitic acid. Under controlled uniaxial stress, the natural rubber sample with 0 parts per hundred rubber (phr carbon black loading exhibits fixity and recovery of 80 ± 10%. Motivation of this research is primarily on practicability of palmitic acid to be used as a swelling agent for shape memory properties. Results show that palmitic acid is a relatively good swelling agent to induce shape memory properties into natural rubber.

  13. their use as Accelerator in Curing Process of Rubber Compounds

    Directory of Open Access Journals (Sweden)

    S. taghvaee

    2007-06-01

    Full Text Available In some special cases, rubber compounds with high amounts of unsaturated elastomer are recommended with organic sulfur donors instead of mineral sulfurs. In this condition, activated sulfur is produced in situ and curingprocess is facilitated without accelerators. Organic sulfur donor compounds have low thermal stability and in the vulcanization temperature produce free and activated sulfurs. The advantages of these compounds are:1. High effectiveness of curing agent in low quantities in rubber compounds manufacturing.2. Producing activated sulfurs in controlled condition and avoiding the over curing of rubber compounds.In this report the novel synthesis of some derivatives of diamino-disulfides which can be applied as sulfur donors in vulcanization of special rubber compounds is introduced. The key process is reaction of sulfurmonochloride with amines in petroleum ether as solvent in low temperature. Dithio-dimorpholine(DTDM, dithio-dipipyridyl (DTDP, dithio-bis dibutylamine (DTBDB and dithio-bisdiisopropyl amine (DTBDI were prepared according to this method. All products thus obtained were characterized by 1H and 13C-NMR spectroscopies. The effects of accelerating and sulfur donoring of all prepared agents were detected in rubber compounds with natural and synthetic rubber bases. All physical, chemical, reological and mechanical properties of rubber compounds based on prepared sulfur donors were characterized.

  14. Mechanical properties and durability of crumb rubber concrete

    Science.gov (United States)

    Chylík, Roman; Trtík, Tomáš; Fládr, Josef; Bílý, Petr

    2017-09-01

    This paper is focused on concrete with admixture of rubber powder, generally called crumb rubber concrete (CRC). The inspiration was found in Arizona, where one of the first CRCs has been created. However, Arizona has completely different climates than Central Europe. Could we use the crumb rubber concrete on construction applications in the Central European climate too? The paper evaluates the influence of the rubber powder on material characteristics and durability of CRC. CRCs with various contents of fine and coarse crumb powder were compared. The tested parameters were slump, air content, permeability, resistance of concrete to water with deicing chemicals, compressive and splitting tensile strength. The tests showed that workability, compressive strength and permeability decreased as the amount of rubber increased, but the air content increased as the rubber content increased. Photos of air voids in cement matrix from electron microscope were captured. The results of laboratory tests showed that admixture of rubber powder in concrete could have a positive impact on durability of concrete and concurrently contribute to sustainable development. Considering the lower compressive strength, CRC is recommended for use in applications where the high strength of concrete is not required.

  15. Model fire tests on polyphosphazene rubber and polyvinyl chloride (PVC)/nitrile rubber foams

    Science.gov (United States)

    Widenor, W. M.

    1978-01-01

    A video tape record of model room fire tests was shown, comparing polyphosphazene (P-N) rubber and polyvinyl chloride (PVC)/nitrile rubber closed-cell foams as interior finish thermal insulation under conditions directly translatable to an actual fire situation. Flashover did not occur with the P-N foam and only moderate amounts of low density smoke were formed, whereas with the PVC/nitrile foam, flashover occurred quickly and large volumes of high density smoke were emitted. The P-N foam was produced in a pilot plant under carefully controlled conditions. The PVC/nitrile foam was a commercial product. A major phase of the overall program involved fire tests on P-N open-cell foam cushioning.

  16. Functionalization of Liquid Natural Rubber via Oxidative Degradation of Natural Rubber

    Directory of Open Access Journals (Sweden)

    Suhawati Ibrahim

    2014-12-01

    Full Text Available Natural rubber (NR is a high molecular weight natural polymer and can be degraded to liquid natural rubber (LNR leaving certain functional groups at the end of chains. In this study, LNR samples prepared via oxidative degradation using H2O2 and NaNO2 as reagents were found to have different end groups depending on the pH of the reaction medium. In an acidic medium, LNR with hydroxyl terminal groups was formed as the degradation reaction was initiated by hydroxyl radicals produced from decomposition of peroxynitrite acid. In contrast, a redox reaction took place in an alkaline medium to yield LNR with carbonyl terminal groups. The mechanisms of reaction are discussed and proposed to explain the formation of different end groups when reaction carried out in acidic and alkaline media. Chain degradation in an acidic medium seems to be more effective than in an alkaline medium, and thus yields LNR with lower Mn.

  17. The cross linking of EPDM and NBR rubber

    Directory of Open Access Journals (Sweden)

    Samardžija-Jovanović Suzana

    2005-01-01

    Full Text Available In the process of macromolecule cross linking, the choice of type and quantity of the components and the experimental conditions are important to obtain the new cross linked materials with better mechanical and chemical characteristics. The cross linking method depends on the rubber type and structure. Intermolecular cross linking results in the formation elastomer network. The basis of the cross linking process, between ethylene propylene diene rubber (EPDM and acrylonitrile butadiene rubber (NBR, is a chemical reaction. Fillers and other additives are present in different mass ratios in the material. The exploitation properties of the cross linked materials depend on the quantity of additive in the cross linked systems.

  18. Shear Flow Induced Alignment of Carbon Nanotubes in Natural Rubber

    Directory of Open Access Journals (Sweden)

    Yan He

    2015-01-01

    Full Text Available A new procedure for the fabrication of natural rubber composite with aligned carbon nanotubes is provided in this study. The two-step approach is based on (i the preparation of mixture latex of natural rubber, multiwalled carbon nanotubes, and other components and (ii the orientation of carbon nanotubes by a flow field. Rubber composite sheets filled with variable volume fraction of aligned carbon nanotubes were fabricated and then confirmed by transmission electron microscopy and Raman spectroscopy studies. An obvious increase in thermal conductivity has been obtained after the alignment of carbon nanotubes. The dynamic mechanical analysis was carried out in a tear mode for the composite.

  19. A kinetic model of reversion type cure for rubber compounds

    Energy Technology Data Exchange (ETDEWEB)

    Han, I.S.; Chung, C.B.; Kang, S.J.; Kim, S.J. [Chonnam National University, Kwangju (Korea, Republic of); Jung, H.C. [Research and Development Center of Kumho Tire Co., Ltd., Kwangju (Korea, Republic of)

    1998-03-01

    A cure kinetic model was presented to explain the reversion and the induction period commonly found in the vulcanization of rubber compounds. The model has three kinetic rate constants and one induction time which should be determined on the basis of isothermal rheometer curves. The torque curves calculated using the estimated parameters showed an excellent agreement with the measured curves for two rubber samples. An Arrhenius type relation was adopted to account for the temperature dependence of each kinetic parameter, and the corresponding Arrhenius plot showed very good linearity. It was shown that the proposed model can be used for predicting the state of cure for rubber compounds which undergo nonisothermal cure steps.

  20. SUPPLY-CHAIN OF NATURAL RUBBER IN INDONESIA

    Directory of Open Access Journals (Sweden)

    Bustanul Arifin

    2011-08-01

    Full Text Available Normal 0 false false false MicrosoftInternetExplorer4 st1\\:*{behavior:url(#ieooui } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin:0cm; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} The study examines the supply chain of natural rubber production in Indonesia and assessing the transmission of prices to rubber growers and provides recommendations for a suitable scheme that would help to ensure high production standards and a sustainable return for natural rubber production.  The frameworks to examine the performance of supply chain of rubber marketing rely mostly on the efficiency level of marketing system of natural rubbers, including the value chain principles in marketing margin, and revealed price transmission from consumers to growers. The results show that the roles of subdistrict middlemen are extremely crucial in moving up the slabs from the village level to urban areas, where trader-brokers are expecting the slabs to be forwarded directly to crumb-rubber factories.  Changes in world price, hence the profits being accumulated by traders and rubber factories, are not transmitted properly to rubber farmers and/or sharetappers. Information asymmetry, the access over price information, and immediate response of rubber growers to the change in world price could explain this non-cointegration in price data between growers and exporters.  In the near future, the policy reforms in supply chain of natural rubber marketing in Indonesia should carefully address these issues in a more comprehensive manner.  Finally, in order to contribute to the positive environmental and social benefits, the major challenge for natural rubber

  1. Interfacial interaction between the epoxidized natural rubber and silica in natural rubber/silica composites

    Science.gov (United States)

    Xu, Tiwen; Jia, Zhixin; Luo, Yuanfang; Jia, Demin; Peng, Zheng

    2015-02-01

    The epoxidized natural rubber (ENR) as an interfacial modifier was used to improve the mechanical and dynamical mechanical properties of NR/silica composites. In order to reveal the interaction mechanism between ENR and silica, the ENR/Silica model compound was prepared by using an open mill and the interfacial interaction of ENR with silica was investigated by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), X-ray diffraction (XRD) and stress-strain testing. The results indicated that the ring-opening reaction occurs between the epoxy groups of ENR chains and Si-OH groups on the silica surfaces and the covalent bonds are formed between two phases, which can improve the dispersion of silica in the rubber matrix and enhance the interfacial combination between rubber and silica. The ring-opening reaction occurs not only in vulcanization process but also in mixing process, meanwhile, the latter seems to be more important due to the simultaneous effects of mechanical force and temperature.

  2. Self-healing properties of carbon nanotube filled natural rubber/bromobutyl rubber blends

    Directory of Open Access Journals (Sweden)

    H. H. Le

    2017-03-01

    Full Text Available In the present work, the development and characterization of an intrinsically self-healable material based on butyl imidazole modified bromobutyl rubber (BIIR/natural rubber (NR blends, which are filled with carbon nanotubes (CNTs are reported. It was found that the addition of CNTs and the blending with NR significantly enhance the tensile strength of the BIIR composites. The use of butyl imidazole as physical cross-linker for the BIIR phase provides the blend composites the non-covalent bondings, which are responsible for their self-healing properties. Owing to the increase of the viscosity of the BIIR phase upon its physical crosslinking the island-matrix morphology of the blend changes over to a co-continuous structure. The preferential wetting of the CNT surface by the low-loading NR phase in the NR/BIIR blends can be explained by the good rubber-filler interaction between the linked phospholipids of the NR molecules and the π-electrons of the CNT surface. As a result, the favored localization of the CNTs in the NR phase strongly improves the electrical properties of the blends according to the double percolation theory. On the other hand it does not deteriorate the self-healing of the BIIR phase. The high electrical conductivity provides us a possibility to heat the blend by application of an electrical voltage in order to accelerate the self-healing process.

  3. Interfacial interaction between the epoxidized natural rubber and silica in natural rubber/silica composites

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Tiwen [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Jia, Zhixin, E-mail: zxjia@scut.edu.cn [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Luo, Yuanfang; Jia, Demin [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510640 (China); Peng, Zheng [Agricultural Product Processing Research Institute, Chinese Academy of Tropical Agriculture Sciences, Zhanjiang 524001 (China)

    2015-02-15

    Highlights: • Substantiate the ring open reaction between Si-OH of silica and epoxy groups of ENR. • ENR can act as a bridge between NR and silica to enhance the interfacial interaction. • As a modifier, ENR gets the potential to be used in the tread of green tire for improving the wet skid resistance apparently. - Abstract: The epoxidized natural rubber (ENR) as an interfacial modifier was used to improve the mechanical and dynamical mechanical properties of NR/silica composites. In order to reveal the interaction mechanism between ENR and silica, the ENR/Silica model compound was prepared by using an open mill and the interfacial interaction of ENR with silica was investigated by Fourier transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), X-ray diffraction (XRD) and stress–strain testing. The results indicated that the ring-opening reaction occurs between the epoxy groups of ENR chains and Si-OH groups on the silica surfaces and the covalent bonds are formed between two phases, which can improve the dispersion of silica in the rubber matrix and enhance the interfacial combination between rubber and silica. The ring-opening reaction occurs not only in vulcanization process but also in mixing process, meanwhile, the latter seems to be more important due to the simultaneous effects of mechanical force and temperature.

  4. Effect of Nanoclay on Natural Rubber Microstructure

    Energy Technology Data Exchange (ETDEWEB)

    Carretero-Gonzalez,J.; Retsos, H.; Verdejo, R.; Toki, S.; Hsiao, B.; Giannelis, E.; Lopez-Manchado, M.

    2008-01-01

    The inclusion of highly anisotropic clay nanoparticles (nanoclays) in cross-linked natural rubber (NR) provides a more homogeneous distributed network structure and induces an early onset as well as enhancement of crystallization under uniaxial deformation. The molecular structure of the polymer network and its morphological changes during deformation were characterized by using broadband dielectric spectroscopy and in situ synchrotron wide-angle X-ray diffraction, respectively. It was found that the presence of nanoclay introduces a dual crystallization mechanism due to the alignment of nanoparticles during stretching. The improved properties in NR-nanoclay nanocomposites can be attributed to both microstructural and morphological changes induced by nanoclay as well as to the nanoclay mobility in the NR matrix during crystallization. The interplay of these factors during deformation contributes to the formation of a supernetwork structure containing cross-linked chemical chains, nanofiller, and crystallizable networks with similar length scales.

  5. The rubber hand illusion in a mirror.

    Science.gov (United States)

    Bertamini, Marco; Berselli, Nausicaa; Bode, Carole; Lawson, Rebecca; Wong, Li Ting

    2011-12-01

    In the rubber hand illusion (RHI) one's hand is hidden, and a fake hand is visible. We explored the situation in which visual information was available indirectly in a mirror. In the mirror condition, compared to the standard condition (fake hand visible directly), we found no reduction of the RHI following synchronised stimulation, as measured by crossmanual pointing and by a questionnaire. We replicated the finding with a smaller mirror that prevented visibility of the face. The RHI was eliminated when a wooden block replaced the fake hand, or when the hand belonged to another person or mannequin. We conclude that awareness of the reflection is the critical variable, despite the distant visual localisation of the hand in a mirror and the third-person perspective. Stimuli seen in a mirror activate the same response as stimuli seen in peripersonal space, through knowledge that they are near one's body. Copyright © 2011 Elsevier Inc. All rights reserved.

  6. Polybenzoxazole-filled nitrile butadiene rubber compositions

    Science.gov (United States)

    Gajiwala, Himansu M. (Inventor); Guillot, David G. (Inventor)

    2008-01-01

    An insulation composition that comprises at least one nitrile butadiene rubber (NBR) having an acrylonitrile content that ranges from approximately 26% by weight to approximately 35% by weight and polybenzoxazole (PBO) fibers. The NBR may be a copolymer of acrylonitrile and butadiene and may be present in the insulation composition in a range of from approximately 45% by weight to approximately 56% by weight of a total weight of the insulation composition. The PBO fibers may be present in a range of from approximately 3% by weight to approximately 10% by weight of a total weight of the insulation composition. A rocket motor including the insulation composition and a method of insulating a rocket motor are also disclosed.

  7. Crumb Rubber in cold recycled bituminous mixes

    DEFF Research Database (Denmark)

    Dondi, Giulio; Tataranni, Piergiorgio; Pettinari, Matteo

    2014-01-01

    Today recycling is one of the most innovative and interesting techniques for the rehabilitation of destressed road pavements. In recent years the increased interest in this process, has led to the development of various alternative methods for the recovery and the reuse of road bituminous materials....... Cold recycling is, among the recycling techniques, certainly the most studied and developed: it allows the recovering of bituminous material from an existing pavement without the addition of heat, whilst ensuring the creation of high quality bound base layers. A wide range of materials have been tested...... together with Reclaimed Asphalt Pavement (RAP) and, consequently, there is a large number of variables that can be considered in the mix-design process of new eco-friendly Cold Recycled Mixes. In particular, the present research involves the use of Crumb Rubber within a mixture containing 100% Reclaimed...

  8. Behavior of Rubber Materials under Exposure to High Electric Fields

    DEFF Research Database (Denmark)

    Candela Garolera, Anna; Holbøll, Joachim; Henriksen, M,

    2013-01-01

    The effect of high electrical stress on rubber materials is investigated by performing breakdown tests and tracking resistance tests on selected samples. The study is focused on the relationship between the dielectric strength and the thickness of the samples, as well as the influence of the inte......The effect of high electrical stress on rubber materials is investigated by performing breakdown tests and tracking resistance tests on selected samples. The study is focused on the relationship between the dielectric strength and the thickness of the samples, as well as the influence...... of the interfaces between different layers of material. Tracking resistance tests are also performed on the rubber material. The purpose is to provide a complete study of the applicability of the rubber material in thunderstorm environments....

  9. Method for Molding Structural Parts Utilizing Modified Silicone Rubber

    Science.gov (United States)

    Weiser, Erik S. (Inventor); Baucom, Robert M. (Inventor); Snoha, John J. (Inventor)

    1998-01-01

    This invention improves upon a method for molding structural parts from preform material. Preform material to be used for the part is provided. A silicone rubber composition containing entrained air voids is prepared. The silicone rubber and preform material assembly is situated within a rigid mold cavity used to shape the preform material to die desired shape. The entire assembly is heated in a standard heating device so that the thermal expansion of the silicone rubber exerts the pressure necessary to force the preform material into contact with the mold container. The introduction of discrete air voids into the silicone rubber allows for accurately controlled pressure application on the preform material at the cure temperature.

  10. Super Lightweight, Metal Rubber Fabric for Extreme Space Environments Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic has fabricated revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films via layer-by-layer, molecular self-assembly, which...

  11. Metal Rubber Sensor Appliquis for Rotor Blade Air Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Thin film Metal RubberTM sensor appliqus have the potential to reduce the time, complexity and cost of measuring air flow-induced skin friction during the...

  12. Thermodynamics of a Simple Rubber-Band Heat Engine

    Science.gov (United States)

    Mullen, J. G.; And Others

    1975-01-01

    Outlines the basic engine design and nomenclature, develops some relations between the state parameters of the rubber-band system, defines engine efficiency, and compares the Archibald engine with the Carnot engine. (GS)

  13. Multifunctional, Nanostructured Metal Rubber Protective Films for Space Exploration Project

    Data.gov (United States)

    National Aeronautics and Space Administration — NanoSonic has developed revolutionary nanostructured, yet macroscale, multifunctional Metal RubberTM films. In support of NASA's Vision for Space Exploration, low...

  14. ORIGINAL ARTICLES Allergenicity of latex rubber products used in ...

    African Journals Online (AJOL)

    , to minimise the risk of sensitisation to these proteins. Background. Allergens from latex products in health care settings are known to trigger latex-induced allergic reactions in HCWs. Adverse effects associated with the use of latex rubber ...

  15. Amplitude-temperature analysis of hard rubber by torsional vibration

    Czech Academy of Sciences Publication Activity Database

    Šulc, Petr; Pešek, Luděk; Bula, Vítězslav; Cibulka, Jan; Košina, Jan

    2016-01-01

    Roč. 821, č. 2016 (2016), s. 295-302 ISSN 1660-9336 Institutional support: RVO:61388998 Keywords : hard rubber * torsion vibration * finite deformation * parameter identification Subject RIV: BI - Acoustics

  16. Tailoring magnetic and dielectric properties of rubber ferrite ...

    Indian Academy of Sciences (India)

    Unknown

    Department of Polymer Science and Rubber Technology, Cochin University of Science and. Technology, Cochin 682 022, India. ‡Physical Chemistry Division, National Chemical Laboratory, Pune 411 008, India. MS received 14 May 2001.

  17. Effect of Graphite on the Properties of Natural Rubber

    Directory of Open Access Journals (Sweden)

    Auda jabber Braihi

    2016-09-01

    Full Text Available Natural rubber-graphite composites (0, 1, 2, 3, 4 pphr graphite were prepared on a laboratory two-roll mill. Swelling measurements were used to evaluate the impacts of graphite on the properties of natural rubber. Swelling results showed that the volume fraction of natural rubber in the swollen gel, the interaction parameter, and the cross-link density decreased by increasing graphite loadings, while the average molecular weight of natural rubber between cross-links increased. Vulcanization results showed that only scorch time parameter increased with increasing graphite loadings, while other parameters (Max. torque, Min. torque, cure rate and cure rate index decreased. Both thermal and AC conductivities increased.

  18. Strength of Concrete Containing Rubber Particle as Partial Cement Replacement

    Directory of Open Access Journals (Sweden)

    Abdullah Siti Radziah

    2016-01-01

    Full Text Available Uncontrolled issues of disposal waste tire rubber create huge environmental impact and health hazards. An alternative viable solution to minimize these problems is by utilizing the waste rubber tires in construction materials, which in turn can reduce the use of natural resources and eventually lessen the cost of construction. This paper mainly focuses on the use of waste rubber tires particles in concrete with different set of composition ranging from 3 to 12% of cement replacement. Concrete cubes size of 150mm x 150mm x 150mm were prepared for compressive strength test, and concrete cylinders size of 150m x 300mm were prepared for splitting tensile test. The result shows that the compressive and split tensile strength of concrete with rubber as cement replacements is 6-21% lower than the normal concrete.

  19. High breakdown-strength composites from liquid silicone rubbers

    DEFF Research Database (Denmark)

    Vudayagiri, Sindhu; Zakaria, Shamsul Bin; Yu, Liyun

    2014-01-01

    In this paper we investigate the performance of liquid silicone rubbers (LSRs) as dielectric elastomer transducers. Commonly used silicones in this application include room-temperature vulcanisable (RTV) silicone elastomers and composites thereof. Pure LSRs and their composites with commercially...

  20. Lightweight Metal RubberTM Sensors and Interconnects Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The objective of this NASA Phase II program is to develop and increase the Technology Readiness Level of multifunctional Metal RubberTM (MRTM) materials that can be...