A Detailed Study of FDIRC Prototype with Waveform Digitizing Electronics in Cosmic Ray Telescope Using 3D Tracks

International Nuclear Information System (INIS)

Nishimura, K.; Dey, B.; Aston, D.; Leith, D.W.G.S.; Ratcliff, B.; Roberts, D.; Ruckman, L.; Shtol, D.; Varner, G.S.; Va'vra, J.

2012-01-01

We present a detailed study of a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC) with waveform digitizing electronics. In this test study, the FDIRC prototype has been instrumented with seven Hamamatsu H-8500 MaPMTs. Waveforms from ∼450 pixels are digitized with waveform sampling electronics based on the BLAB2 ASIC, operating at a sampling speed of ∼2.5 GSa/s. The FDIRC prototype was tested in a large cosmic ray telescope (CRT) providing 3D muon tracks with ∼1.5 mrad angular resolution and muon energy of E muon > 1.6 GeV. In this study we provide a detailed analysis of the tails in the Cherenkov angle distribution as a function of various variables, compare experimental results with simulation, and identify the major contributions to the tails. We demonstrate that to see the full impact of these tails on the Cherenkov angle resolution, it is crucial to use 3D tracks, and have a full understanding of the role of ambiguities. These issues could not be fully explored in previous FDIRC studies where the beam was perpendicular to the quartz radiator bars. This work is relevant for the final FDIRC prototype of the PID detector at SuperB, which will be tested this year in the CRT setup.

Detail study of SiC MOSFET switching characteristics

DEFF Research Database (Denmark)

Li, Helong; Munk-Nielsen, Stig

2014-01-01

This paper makes detail study of the latest SiC MOSFETs switching characteristics in relation to gate driver maximum current, gate resistance, common source inductance and parasitic switching loop inductance. The switching performance of SiC MOSFETs in terms of turn on and turn off voltage...

The detail is dead - long live the detail!

DEFF Research Database (Denmark)

Larsen, Steen Nepper; Dalgaard, Kim; Kerstens, Vencent

2018-01-01

architecture when we look into architectural history. Too classic examples are; Adolf Loos who provoked already in 1908 with his statement; "Ornament and Crime", which contested the unconscious decorations of contemporary architects. Similarly, referring to the little need for superfluous detailing; "Less...... not change the fact that it is more important than ever to bring this 'small' architectural world to attention. Today, the construction industry is dictated by an economic management that does not leave much room for thorough studies of architectural details or visionary experiments. Today's more efficient......_Delft about the Symposium; "The Detail is Dead - Long Live the Detail". For this occasion a number of leading Danish and Northern European architects, researchers and companies were invited to discuss and suggest their 'architectural detail' and the challenges they face in today's construction. This book...

A detailed BWR recirculation loop model for RELAP

Energy Technology Data Exchange (ETDEWEB)

Araiza-Martínez, Enrique, E-mail: enrique.araiza@inin.gob.mx; Ortiz-Villafuerte, Javier, E-mail: javier.ortiz@inin.gob.mx; Castillo-Durán, Rogelio, E-mail: rogelio.castillo@inin.gob.mx

2017-01-15

Highlights: • A new detailed BWR recirculation loop model was developed for RELAP. • All jet pumps, risers, manifold, suction and control valves, and recirculation pump are modeled. • Model is tested against data from partial blockage of two jet pumps. • For practical applications, simulation results showed good agreement with available data. - Abstract: A new detailed geometric model of the whole recirculation loop of a BWR has been developed for the code RELAP. This detailed model includes the 10 jet pumps, 5 risers, manifold, suction and control valves, and the recirculation pump, per recirculation loop. The model is tested against data from an event of partial blockage at the entrance nozzle of one jet pump in both recirculation loops. For practical applications, simulation results showed good agreement with data. Then, values of parameters considered as figure of merit (reactor power, dome pressure, core flow, among others) for this event are compared against those from the common 1 jet pump per loop model. The results show that new detailed model led to a closer prediction of the reported power change. The detailed recirculation loop model can provide more reliable boundary condition data to a CFD models for studies of, for example, flow induced vibration, wear, and crack initiation.

Waste Handling Equipment Development Test and Evaluation Study

International Nuclear Information System (INIS)

R.L. Tome

1998-01-01

The purpose of this study is to identify candidate Monitored Geologic Repository (MGR) surface waste handling equipment for development testing. This study will also identify strategies for performing the development tests. Development testing shall be implemented to support detail design and reduce design risks. Development testing shall be conducted to confirm design concepts, evaluate alternative design concepts, show the availability of needed technology, and provide design documentation. The candidate equipment will be selected from MGR surface waste handling equipment that is the responsibility of the Management and Operating Contractor (M and O) Surface Design Department. The equipment identified in this study is based on Viability Assessment (VA) design. The ''Monitored Geologic Repository Test and Evaluation Plan'' (MGR T and EP), Reference 5.1, was used as a basis for this study. The MGR T and EP reflects the extent of test planning and analysis that can be conducted, given the current status of the MGR requirements and latest VA design information. The MGR T and EP supports the appropriate sections in the license application (LA) in accordance with 10 CFR 60.2 1(c)(14). The MGR T and EP describes the following test activities: site characterization to confirm, by test and analysis, the suitability of the Yucca Mountain site for housing a geologic repository; development testing to investigate and document design concepts to reduce risk; qualification testing to verify equipment compliance with design requirements, specifications, and regulatory requirements; system testing to validate compliance with MGR requirements, which include the receipt, handling, retrieval, and disposal of waste; periodic performance testing to verify preclosure requirements and to demonstrate safe and reliable MGR operation; and performance confirmation modeling, testing, and analysis to verify adherence to postclosure regulatory requirements. Development test activities can be

Method for determining detailed rod worth profiles at low power in the fast test reactor

International Nuclear Information System (INIS)

Sevenich, R.A.

1975-08-01

A method for obtaining a detailed rod worth profile at low power for a slow control rod insertion is presented. The accuracy of the method depends on a preparatory experiment in which the test rod is dropped quickly to yield, upon analysis, the magnitude of the rod worth and an effective source value. These numbers are employed to initialize the inverse kinetics analysis for the slow insertion. Corrections for changes in detection efficiency are not included for the simulated experiments. (U.S.)

Study of geological details towards feasibility of uranium project: Indian case studies

International Nuclear Information System (INIS)

Sarangi, A.

2014-01-01

Appropriate technical evaluation of geological details at early stage of exploration is the key to minimising the lead-time between discovery and production. This has a major influence on economic viability of the deposits. Indian uranium deposits are of medium-tonnage and low-grade occurring in dissimilar geological provinces. Detailed studies of geological characteristics of these deposits are very vital to the proper selection of technology and subsequent successful operation. The method of mining (underground/open pit/in-situ recovery) is influenced by the ore body depth, size, grade, configuration, hostrock and adjoining strata characteristics, hydrological condition etc. The ore processing technology is also subjective to mineralogical characteristics of the ore. In order to draw the flowsheet, determine process parameters and selection of reagents, a comprehensive study on identification of minerals and their probable metallurgical characteristics, general physical relationship between various minerals, mineral liberation size etc is of great significance. The technology for disposal of tailings is also influenced by geological/geo-hydrological characteristics. The key to successful operation of Indian uranium deposits lies in outlining a pre-development strategy as the exploration advances to different stages. This phase called ''exploratory mining'' - which starts with detailed exploration and ends with approval of the project is very critical for early commissioning of the project. The activities during this period include collection of representative drill core samples during exploration, laboratory studies, geo-technical studies and determination of geomechanical properties of ore and waste rock etc. Later, the ore lenses are accessed through limited entry(ies). Developments along the ore body helps in better understanding of the configuration of the lenses. Studies for strata control in case of underground mining are carried out towards deciding the

Research on the Hotel Image Based on the Detail Service

Science.gov (United States)

Li, Ban; Shenghua, Zheng; He, Yi

Detail service management, initially developed as marketing programs to enhance customer loyalty, has now become an important part of customer relation strategy. This paper analyzes the critical factors of detail service and its influence on the hotel image. We establish the theoretical model of influencing factors on hotel image and propose corresponding hypotheses. We use applying statistical method to test and verify the above-mentioned hypotheses. This paper provides a foundation for further study of detail service design and planning issues.

Author Details

African Journals Online (AJOL)

Petrology of the Cenomanian Upper Member of the Mamfe Embayment, southwestern Cameroon Details · Vol 38, No 1 (2002) - Articles Sequence stratigraphy of Iso field, western onshore Niger Delta, Nigeria Details · Vol 39, No 2 (2003) - Articles Preliminary studies on the lithostratigraphy and depositional environment of ...

Detailed Sensory Memory, Sloppy Working Memory

OpenAIRE

Sligte, Ilja G.; Vandenbroucke, Annelinde R. E.; Scholte, H. Steven; Lamme, Victor A. F.

2010-01-01

Visual short-term memory (VSTM) enables us to actively maintain information in mind for a brief period of time after stimulus disappearance. According to recent studies, VSTM consists of three stages - iconic memory, fragile VSTM, and visual working memory - with increasingly stricter capacity limits and progressively longer lifetimes. Still, the resolution (or amount of visual detail) of each VSTM stage has remained unexplored and we test this in the present study. We presented people with a...

Detailed leak detection test plan and schedule for the Oak Ridge National Laboratory LLLW active pipelines

International Nuclear Information System (INIS)

Douglas, D.G.; Starr, J.W.; Juliano, T.M.; Maresca, J.W. Jr.

1993-09-01

This document provides a detailed leak detection test plan and schedule for leak testing many of the pipelines that comprise the active portion of the liquid low-level waste (LLLW) system at the Oak Ridge National Laboratory (ORNL). This plan was prepared in response to the requirements of the Federal Facility Agreement (FFA) between the US Department of Energy (DOE) and two other agencies, the US Environmental Protection Agency (EPA) and the Tennessee Department of Environment and Conservation (TDEC). The LLLW system is an interconnected complex of tanks and pipelines. The FFA distinguishes four categories of tank and pipeline systems within this complex: new systems (Category A), doubly contained systems (Category B), singly contained systems (Category C), and inactive systems (Category D). The FFA specifically requires leak testing of the Category C systems. This plan and schedule addresses leak testing of the Category C pipelines and those doubly contained pipelines that do not fully meet the requirements for secondary containment as listed in the FFA

A detailed study of FDIRC prototype with waveform digitizing electronics in cosmic ray telescope using 3D tracks

Science.gov (United States)

Nishimura, K.; Dey, B.; Aston, D.; Leith, D. W. G. S.; Ratcliff, B.; Roberts, D.; Ruckman, L.; Shtol, D.; Varner, G. S.; Va'vra, J.

2013-02-01

We present a detailed study of a novel Cherenkov imaging detector called the Focusing DIRC (FDIRC) with waveform digitizing electronics. In this study, the FDIRC prototype has been instrumented with seven Hamamatsu H-8500 MaPMTs. Waveforms from 384 pixels are digitized with waveform sampling electronics based on the BLAB2 ASIC, operating at a sampling speed of ∼2.5 GSa/s. The FDIRC prototype was tested in a large cosmic ray telescope (CRT) providing 3D muon tracks with ∼1.5 mrad angular resolution and muon energy of Emuon> 1.6 GeV. In this study we provide a detailed analysis of the tails in the Cherenkov angle distribution as a function of various variables, compare experimental results with simulation, and identify the major contributions to the tails. We demonstrate that to see the full impact of these tails on the Cherenkov angle resolution, it is crucial to use 3D tracks, and have a full understanding of the role of reconstruction ambiguities. These issues could not be fully explored in previous FDIRC studies where the beam was perpendicular to the quartz radiator bars. This work is relevant for the final FDIRC prototype of the PID detector at SuperB, which will be tested this year in the CRT setup.

Victory Has a Thousand Fathers: Detailed Counterinsurgency Case Studies

Science.gov (United States)

2010-01-01

Fathers: Detailed Counterinsurgency Case Studies There was more progress toward a peace agreement in 1999 when Nelson Mandela was designated as...mediator for the conflict. While Mandela still failed to bring the rebel groups to the table, he was able to negotiate an agreement among the political

Capturing Fine Details Involving Low-Cost Sensors -a Comparative Study

Science.gov (United States)

Rehany, N.; Barsi, A.; Lovas, T.

2017-11-01

Capturing the fine details on the surface of small objects is a real challenge to many conventional surveying methods. Our paper discusses the investigation of several data acquisition technologies, such as arm scanner, structured light scanner, terrestrial laser scanner, object line-scanner, DSLR camera, and mobile phone camera. A palm-sized embossed sculpture reproduction was used as a test object; it has been surveyed by all the instruments. The result point clouds and meshes were then analyzed, using the arm scanner's dataset as reference. In addition to general statistics, the results have been evaluated based both on 3D deviation maps and 2D deviation graphs; the latter allows even more accurate analysis of the characteristics of the different data acquisition approaches. Additionally, own-developed local minimum maps were created that nicely visualize the potential level of detail provided by the applied technologies. Besides the usual geometric assessment, the paper discusses the different resource needs (cost, time, expertise) of the discussed techniques. Our results proved that even amateur sensors operated by amateur users can provide high quality datasets that enable engineering analysis. Based on the results, the paper contains an outlook to potential future investigations in this field.

Air barrier details: How effective are they

Energy Technology Data Exchange (ETDEWEB)

A project was initiated to measure the air leakage through three typical details in wood frame walls: the header joist, electric outlets, and window openings. Three construction methods were tested: the poly approach, where a sealed internal polyethylene sheet and caulking provide the air barrier; an external air barrier approach using a continuous vapor permeable membrane sandwiched between two layers of external wall sheathing; and the airtight drywall approach (ADA), where the interior gypsum board finish along with framing and gaskets are the air barrier. Twelve sample panels using each of the three details were built using each of the construction approaches. A traditional wood-frame wall construction detail, with no effort made to create a continuous air barrier, was also built and tested for comparison. The samples were put in a test chamber so that air pressures could create infiltration or exfiltration through the panel under loads similar to those due to wind action. Measurements were made at several stages during construction of each sample to see the effect of different components on the air leakage. Overall, all but the traditional samples and the ADA electrical outlet panel exceeded the current tightness standards for glass and aluminum curtain walls. All three approaches could meet the airtightness standards of the R-2000 program. The total air leakage calculated for each approach is under 20% of that in traditional construction. Of the details tested, window detailing offers the greatest potential for increasing overall airtightness compared to traditional methods. 1 ref., 2 figs., 1 tab.

A study on plate anchor detailing systems of shear re-bar

International Nuclear Information System (INIS)

Tsurumaki, S.; Ujiie, K.; Nishikawa, T.; Kitayama, K.

1995-01-01

For shell walls and base slabs in reactor buildings, besides a large amount of main bars, numerous shear re-bars have been employed to resist to out-of-plane force. As a result , detailing work involving shear re-bar is extremely involved. For example, the employed re-bar anchor method differs from the ordinary methods in which, a end of shear re-bar with 135-degrees hook or with anchor plate type and another re-bar end with 90-degrees hook are used. However the structural characteristics in members using shear re-bar of the bolt-mounted anchor plate have not yet been examined. A test was performed to confirm the effects of anchor methods for shear re-bars on shearing behavior of members. This paper describes the test plan, method and results. (author). 12 figs., 7 tabs

Detailed analysis of the ANO-2 turbine trip test

International Nuclear Information System (INIS)

McDonald, T.A.; Tessier, J.H.; Senda, Y.; Waterman, M.D.

1983-01-01

A RELAP5/MOD1 (Cycle 18) computer code simulation of the ANO-2 turbine trip test from 98% power level was performed for use in vendor code qualification studies. Results focused on potential improvements to simulation capabilities and plant data acquisition systems to provide meaningful comparisons between the calculations and the test data. The turbine trip test was selected because it resulted in an unplanned sequence of events that broadly affected the plant process systems and their controls. The pressurizer spray valve stuck open at an undetermined flow area, and an atmospheric dump valve remained stuck fully open while several atmospheric dump and secondary side safety valves were unavailable throughout. Thus, although the plant remained always in a safe condition, this transient potentially provided an unusual set of data against which the fidelity of a NSSS simulation by RELAP5/MOD1 along with certain vendor analysis codes might be judged

Relativistic Klystron Two-Beam Accelerator studies at the RTA test facility

International Nuclear Information System (INIS)

Westenskow, G.A.; Houck, T.L.; Anderson, D.

1996-01-01

A prototype rf power source based on the Relativistic Klystron Two- Beam Accelerator (RK-TBA) concept is being constructed at LBNL to study physics, engineering, and costing issues. The prototype, called RTA, is described and compared to a full scale design appropriate for driving the Next Linear Collider. Specific details of the induction core test and pulsed power system are presented. Details of the 1-MeV, 1.2-kA induction gun currently under construction are described

E-detailing: information technology applied to pharmaceutical detailing.

Science.gov (United States)

Montoya, Isaac D

2008-11-01

E-detailing can be best described as the use of information technology in the field of pharmaceutical detailing. It is becoming highly popular among pharmaceutical companies because it maximizes the time of the sales force, cuts down the cost of detailing and increases physician prescribing. Thus, the application of information technology is proving to be beneficial to both physicians and pharmaceutical companies. When e-detailing was introduced in 1996, it was limited to the US; however, numerous other countries soon adopted this novel approach to detailing and now it is popular in many developed nations. The objective of this paper is to demonstrate the rapid growth of e-detailing in the field of pharmaceutical marketing. A review of e-detailing literature was conducted in addition to personal conversations with physicians. E-detailing has the potential to reduce marketing costs, increase accessibility to physicians and offer many of the advantages of face-to-face detailing. E-detailing is gaining acceptance among physicians because they can access the information of a pharmaceutical product at their own time and convenience. However, the drug safety aspect of e-detailing has not been examined and e-detailing remains a supplement to traditional detailing and is not yet a replacement to it.

Detailed α -decay study of 180Tl

Science.gov (United States)

Andel, B.; Andreyev, A. N.; Antalic, S.; Barzakh, A.; Bree, N.; Cocolios, T. E.; Comas, V. F.; Diriken, J.; Elseviers, J.; Fedorov, D. V.; Fedosseev, V. N.; Franchoo, S.; Ghys, L.; Heredia, J. A.; Huyse, M.; Ivanov, O.; Köster, U.; Liberati, V.; Marsh, B. A.; Nishio, K.; Page, R. D.; Patronis, N.; Seliverstov, M. D.; Tsekhanovich, I.; Van den Bergh, P.; Van De Walle, J.; Van Duppen, P.; Venhart, M.; Vermote, S.; Veselský, M.; Wagemans, C.

2017-11-01

A detailed α -decay spectroscopy study of 180Tl has been performed at ISOLDE (CERN). Z -selective ionization by the Resonance Ionization Laser Ion Source (RILIS) coupled to mass separation provided a high-purity beam of 180Tl. Fine-structure α decays to excited levels in the daughter 176Au were identified and an α -decay scheme of 180Tl was constructed based on an analysis of α -γ and α -γ -γ coincidences. Multipolarities of several γ -ray transitions deexciting levels in 176Au were determined. Based on the analysis of reduced α -decay widths, it was found that all α decays are hindered, which signifies a change of configuration between the parent and all daughter states.

Detailed kinetic modeling study of n-pentanol oxidation

KAUST Repository

Heufer, Karl Alexander; Sarathy, Mani; Curran, Henry J.; Davis, Alexander C.; Westbrook, Charles K.; Pitz, William J.

2012-01-01

To help overcome the world's dependence upon fossil fuels, suitable biofuels are promising alternatives that can be used in the transportation sector. Recent research on internal combustion engines shows that short alcoholic fuels (e.g., ethanol or n-butanol) have reduced pollutant emissions and increased knock resistance compared to fossil fuels. Although higher molecular weight alcohols (e.g., n-pentanol and n-hexanol) exhibit higher reactivity that lowers their knock resistance, they are suitable for diesel engines or advanced engine concepts, such as homogeneous charge compression ignition (HCCI), where higher reactivity at lower temperatures is necessary for engine operation. The present study presents a detailed kinetic model for n-pentanol based on modeling rules previously presented for n-butanol. This approach was initially validated using quantum chemistry calculations to verify the most stable n-pentanol conformation and to obtain C-H and C-C bond dissociation energies. The proposed model has been validated against ignition delay time data, speciation data from a jet-stirred reactor, and laminar flame velocity measurements. Overall, the model shows good agreement with the experiments and permits a detailed discussion of the differences between alcohols and alkanes. © 2012 American Chemical Society.

Detailed kinetic modeling study of n-pentanol oxidation

KAUST Repository

Heufer, Karl Alexander

2012-10-18

To help overcome the world\\'s dependence upon fossil fuels, suitable biofuels are promising alternatives that can be used in the transportation sector. Recent research on internal combustion engines shows that short alcoholic fuels (e.g., ethanol or n-butanol) have reduced pollutant emissions and increased knock resistance compared to fossil fuels. Although higher molecular weight alcohols (e.g., n-pentanol and n-hexanol) exhibit higher reactivity that lowers their knock resistance, they are suitable for diesel engines or advanced engine concepts, such as homogeneous charge compression ignition (HCCI), where higher reactivity at lower temperatures is necessary for engine operation. The present study presents a detailed kinetic model for n-pentanol based on modeling rules previously presented for n-butanol. This approach was initially validated using quantum chemistry calculations to verify the most stable n-pentanol conformation and to obtain C-H and C-C bond dissociation energies. The proposed model has been validated against ignition delay time data, speciation data from a jet-stirred reactor, and laminar flame velocity measurements. Overall, the model shows good agreement with the experiments and permits a detailed discussion of the differences between alcohols and alkanes. © 2012 American Chemical Society.

Results of Detailed Hydrologic Characterization Tests—Fiscal and Calendar Year 2005

Energy Technology Data Exchange (ETDEWEB)

Spane, Frank A.; Newcomer, Darrell R.

2008-02-27

This report provides the results of detailed hydrologic characterization tests conducted within selected Hanford Site wells during fiscal and calendar year 2005. Detailed characterization tests performed included groundwater-flow characterization, barometric response evaluation, slug tests, in-well vertical groundwater-flow assessments, and a single-well tracer and constant-rate pumping test. Hydraulic property estimates obtained from the detailed hydrologic tests include hydraulic conductivity, transmissivity, specific yield, effective porosity, in-well lateral and vertical groundwater-flow velocity, aquifer groundwater-flow velocity, and depth-distribution profiles of hydraulic conductivity. In addition, local groundwater-flow characteristics (i.e., hydraulic gradient and flow direction) were determined for a site where detailed well testing was performed. Results obtained from these tests provide hydrologic information that supports the needs of Resource Conservation and Recovery Act waste management area characterization as well as sitewide groundwater monitoring and modeling programs. These results also reduce the uncertainty of groundwater-flow conditions at selected locations on the Hanford Site.

Interpretation of the CABRI-RAFT LTX test up to pin failure based on detailed data evaluation and PARAS-2S code analysis

International Nuclear Information System (INIS)

Fukano, Yoshitaka; Sato, Ikken

2001-09-01

The CABRI-RAFT LTX test aims at a study on the fuel-pin-failure mechanism, in-pin fuel motion and post-failure fuel relocation with an annular fuel pin which was pre-irradiated up to peak burn-up of 6.4 at%. The transient test conditions similar to those of the LT4 test were selected in the LTX test using the same type of fuel pin, allowing an effective direct comparison between the two tests. In contrast to the LT4 test which showed a large PCMI-mitigation potential of the annular fuel-pin design, early pin failure occurred in the LTX test when fuel does not seem to have molten. In order to clarify the fuel pin failure mechanism, interpretation of the LTX test up to pin failure is performed in this study, through an experimental data evaluation and a PAPAS-2S-code analysis. The PAPAS-2S code simulates reasonably the fuel thermal conditions such as transient fuel-pin heat-up and fuel melting. The present detailed data evaluation shows that the earlier cladding failure compared with the LT4 test is mainly attributed to the local cladding heat-up. Under the high-temperature condition, plenum gas pressure has a certain potential to explain the observed failure. Fuel swelling-induced PCMI does not seem significant in the LTX test and it may have contributed to the early pin failure only to a limited extent, if any. (author)

XPS Studies of LSCF Interfaces after Cell Testing

Directory of Open Access Journals (Sweden)

Gianfranco DiGiuseppe

2018-01-01

Full Text Available The motivation of this investigation is to explore the possibility of using the depth profile capability of XPS to study interfaces after SOFC button cell testing. The literature uses XPS to study various cathode materials but has devoted little to the understanding of various cathode interfaces especially after testing. In this work, an SOFC button cell is first tested, and then, the LSCF cathode, barrier layer, and electrolyte are sputtered away to study the behavior of different interfaces. This work has shown that some elements have moved into other layers of the SOFC cell. It is argued that the migration of the elements is partly due to a redeposition mechanism after atoms are sputtered away, while the rest is due to interdiffusion between the SDC and YSZ layers. However, additional work is needed to better understand the mechanism by which atoms move around at different interfaces. The cell electrochemical performance is also discussed in some details but is not the focus.

Interpretation of the CABRI-RAFT RB1 and RB2 tests through detailed data evaluation and PAPAS-2S code analysis

International Nuclear Information System (INIS)

Fukano, Yoshitaka; Sato, Ikken

2001-08-01

The CABRI-RAFT RB1 and RB2 tests were aiming at a study on impact of fuel pin failure under an overpower condition leading to fuel melting. Using a special technique, combination of through-cladding failure and fuel melting was realized. In the RB1 test, fuel ejection was prevented under a limited fuel melting condition. On the other hand, significant fuel melting was applied in the RB2 test so as to get the fuel ejection, thereby obtaining information on the fuel ejection behavior. Interpretation for these tests through the detailed experimental data evaluation and the PAPAS-2S code analysis is performed in this study. Through this study, it is indicated that molten fuel ejection can be prevented with the low smear density fuel as far as the fuel melting is not large for a slit-type cladding defect. Fuel ejection becomes possible in the case of significant fuel melting with a very thin solid fuel shell surrounding the molten fuel cavity. However, the rapidness of the fuel ejection with the low smear density fuel is less pronounced compared with that of the high smear density fuel. It is also confirmed that there is considerable DN-precursor release into the coolant flow already before fuel ejection. The result is very useful for evaluation of anomaly detection with DN signal observation. (author)

Numerical models: Detailing and simulation techniques aimed at comparison with experimental data, support to test result interpretation

International Nuclear Information System (INIS)

Lin Chiwen

2001-01-01

This part of the presentation discusses the modelling details required and the simulation techniques available for analyses, facilitating the comparison with the experimental data and providing support for interpretation of the test results. It is organised to cover the following topics: analysis inputs; basic modelling requirements for reactor coolant system; method applicable for reactor cooling system; consideration of damping values and integration time steps; typical analytic models used for analysis of reactor pressure vessel and internals; hydrodynamic mass and fluid damping for the internal analysis; impact elements for fuel analysis; and PEI theorem and its applications. The intention of these topics is to identify the key parameters associated with models of analysis and analytical methods. This should provide proper basis for useful comparison with the test results

Detailed design and first tests of the application software for the instrument control unit of Euclid-NISP

Science.gov (United States)

Ligori, S.; Corcione, L.; Capobianco, V.; Bonino, D.; Sirri, G.; Fornari, F.; Giacomini, F.; Patrizii, L.; Valenziano, L.; Travaglini, R.; Colodro, C.; Bortoletto, F.; Bonoli, C.; Chiarusi, T.; Margiotta, A.; Mauri, N.; Pasqualini, L.; Spurio, M.; Tenti, M.; Dal Corso, F.; Dusini, S.; Laudisio, F.; Sirignano, C.; Stanco, L.; Ventura, S.; Auricchio, N.; Balestra, A.; Franceschi, E.; Morgante, G.; Trifoglio, M.; Medinaceli, E.; Guizzo, G. P.; Debei, S.; Stephen, J. B.

2016-07-01

In this paper we describe the detailed design of the application software (ASW) of the instrument control unit (ICU) of NISP, the Near-Infrared Spectro-Photometer of the Euclid mission. This software is based on a real-time operating system (RTEMS) and will interface with all the subunits of NISP, as well as the command and data management unit (CDMU) of the spacecraft for telecommand and housekeeping management. We briefly review the main requirements driving the design and the architecture of the software that is approaching the Critical Design Review level. The interaction with the data processing unit (DPU), which is the intelligent subunit controlling the detector system, is described in detail, as well as the concept for the implementation of the failure detection, isolation and recovery (FDIR) algorithms. The first version of the software is under development on a Breadboard model produced by AIRBUS/CRISA. We describe the results of the tests and the main performances and budgets.

Feasibility study of the thermo-siphon mock-up test

International Nuclear Information System (INIS)

Choi, Jung Woon; Kim, Young Jin; Lee, Kye Hong; Kim, Young Ki; Jeong, Sang Kwon

2004-09-01

Described is the feasibility of the thermo-siphon mock-up test for the HANARO-CNS facility. The purposes of the mock-up tests are discussed in detail as the three concepts: for the detailed design, for the operation of the CNS facility, for the safety assurance of itself. This report considers the two stages of mock-up tests in terms of the experimental schedule and plan. As the first stage, the small-size mock-up test using Argon will be implemented to obtain the experience in the cryogenic fluid and to understand the basic concept of the CNS thermo-siphon. In the second stage, two kinds of mock-up tests are discussed: the full-scale mock-up test using liquid hydrogen or the integrated final test using hydrogen outside the reactor after the full-scale mock-up test using Freon gas. The contents discussed in this report will be the basis or the guide lines for the mock-up test. In addition, the results of the mock-up test will be the foundation for the safe operation of the HANARO-CNS facility

Ocean Thermal Energy Converstion (OTEC) test facilities study program. Final report. Volume II. Part B

Energy Technology Data Exchange (ETDEWEB)

None

1977-01-17

Results are presented of an 8-month study to develop alternative non-site-specific OTEC facilities/platform requirements for an integrated OTEC test program which may include land and floating test facilities. Volume II--Appendixes is bound in three parts (A, B, and C) which together comprise a compendium of the most significant detailed data developed during the study. Part B provides an annotated test list and describes component tests and system tests.

Family physicians' perceptions of academic detailing: a quantitative and qualitative study

Directory of Open Access Journals (Sweden)

O'Connor Nicolette

2007-10-01

Full Text Available Abstract Background The efficacy of academic detailing in changing physicians' knowledge and practice has been the subject of many primary research publications and systematic reviews. However, there is little written about the features of academic detailing that physicians find valuable or that affect their use of it. The goal of our project was to explore family physicians' (FPs perceptions of academic detailing and the factors that affect their use of it. Methods We used 2 methods to collect data, a questionnaire and semi-structured telephone interviews. We mailed questionnaires to all FPs in the Dalhousie Office of Continuing Medical Education database and analyzed responses of non-users and users of academic detailing. After a preliminary analysis of questionnaire data, we conducted semi-structured interviews with 7 FPs who did not use academic detailing and 17 who did use it. Results Overall response rate to the questionnaire was 33% (289/869. Response rate of non-users of academic detailing was 15% (60/393, of users was 48% (229/476. The 3 factors that most encouraged use of academic detailing were the topics selected, the evidence-based approach adopted, and the handout material. The 3 factors that most discouraged the use of academic detailing were spending office time doing CME, scheduling time to see the academic detailer, and having CME provided by a non-physician. Users of academic detailing rated it as being more valuable than other forms of CME. Generally, interview data confirmed questionnaire data with the exception that interview informants did not view having CME provided by a non-physician as a barrier. Interview informants mentioned that the evidence-based approach adopted by academic detailing had led them to more critically evaluate information from other CME programs, pharmaceutical representatives, and journal articles, but not advice from specialists. Conclusion Users of academic detailing highly value its educational

A detailed experimental study of a DNA computer with two endonucleases.

Science.gov (United States)

Sakowski, Sebastian; Krasiński, Tadeusz; Sarnik, Joanna; Blasiak, Janusz; Waldmajer, Jacek; Poplawski, Tomasz

2017-07-14

Great advances in biotechnology have allowed the construction of a computer from DNA. One of the proposed solutions is a biomolecular finite automaton, a simple two-state DNA computer without memory, which was presented by Ehud Shapiro's group at the Weizmann Institute of Science. The main problem with this computer, in which biomolecules carry out logical operations, is its complexity - increasing the number of states of biomolecular automata. In this study, we constructed (in laboratory conditions) a six-state DNA computer that uses two endonucleases (e.g. AcuI and BbvI) and a ligase. We have presented a detailed experimental verification of its feasibility. We described the effect of the number of states, the length of input data, and the nondeterminism on the computing process. We also tested different automata (with three, four, and six states) running on various accepted input words of different lengths such as ab, aab, aaab, ababa, and of an unaccepted word ba. Moreover, this article presents the reaction optimization and the methods of eliminating certain biochemical problems occurring in the implementation of a biomolecular DNA automaton based on two endonucleases.

Regional and detailed research studies for stone resources in Korea

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-12-01

This report consists of 7 articles. 1) Detail drilling research works on granodiorite stock of Cheanan area near Onyang city in Chungnam province. 2) Regional research studies on granites distributed in Kimje - Jeongeup. 3) Regional survey and feasibility study on diorite rock mass in Kohyeng, Cheonnam province. 4) Regional research study on the stone resources of Hamyang area. 5) A study on variation trends of physical properties of 5 kinds of building stone by means of Weather-Ometer experiment. 6) Borehole radar survey at the granodiorite quarry mine, Cheonan, Chungnam province. 7) Radar velocity tomography in anisotropic media. (author). refs., tabs., figs.

Feasibility study on the transient fuel test loop installation

International Nuclear Information System (INIS)

Kim, J. Y.; Lee, C. Y.

1997-02-01

The design and installation of the irradiation test facility for verification test of the fuel performance are very important in connection with maximization of the utilization of HANARO. The objective of this study is to investigate and analyze the test capsules and loops in research reactors of the other countries and to design preliminarily the eligible transient fuel test facility to be installed in HANARO. The principle subjects of this study are to analyze the contents, kinds and scopes of the irradiation test facilities for nuclear technology development. The guidances for the basic and detail design of the transient fuel test facility in the future are presented. The investigation and analysis of various kinds of test facilities that are now in operation at the research reactors of nuclear advanced countries are carried out. Based on the design data of HANARO the design materials for an eligible transient fuel test facility comprises two pacts : namely, in pile test fuel in reactor core site, and out of pile system regulates the experimental conditions in the in pile test section. Especially for power ramping and cycling selection of the eligible power variation equipment in HANARO is carried out. (author). 13 refs., 4 tabs., 46 figs

Study on Detailing Design of Precast Concrete Frame Structure

Science.gov (United States)

Lida, Tian; Liming, Li; Kang, Liu; Jiao, Geng; Ming, Li

2018-03-01

Taking a certain precast concrete frame structure as an example, this paper introduces the general procedures and key points in detailing design of emulative cast-in-place prefabricated structure from the aspects of structural scheme, precast element layout, shop drawing design and BIM 3D modelling. This paper gives a practical solution for the detailing design of precast concrete frame structure under structural design codes in China.

How should low-contrast detail detectability be measured in fluoroscopy?

International Nuclear Information System (INIS)

Tapiovaara, Markku J.; Sandborg, Michael

2004-01-01

The relationship and precision of four methods for measuring the low-contrast detail detectability in fluoroscopic imaging were studied. These included the physical measurement of the accumulation rate of the square of the signal-to-noise ratio (SNR rate 2 ), two-alternative forced-choice (2-AFC) experiments, sixteen-alternative forced-choice (16-AFC) experiments and subjective determination of the threshold contrast. The precision and sensitivity of the threshold contrast measurement were seen to be modest in the constancy testing of fluoroscopic equipment: only large changes in system performance could be reliably detected by that method. The measurement of the SNR rate 2 is suggested instead. The relationship between the results of the various methods were studied, and it was found that human performance can be related to SNR rate 2 by introducing the concept of the effective image information integration time (t eff ). When measured for an unlimited observation time, it depicts the saturation of human performance in detecting a static low-contrast detail in dynamic image noise. Here, t eff was found to be about 0.6 s in 2-AFC tests and 0.3 s in 16-AFC tests

Adapting Bioretention Construction Details to Local Practices in Finland

Directory of Open Access Journals (Sweden)

Outi Tahvonen

2018-01-01

Full Text Available Bioretention is a method of storm water management that includes several processes following the natural hydrological cycle. Bioretention, or variations of it, include rain gardens and bioswales, infiltrates, filtrates, evapotranspirates, and help to store and manage storm water run-off. A bioretention cell retains water, removes pollutants, and provides water elements for urban green areas. Although bioretention is a promising method for multifunctional storm water management, its construction details should not be copied from other climatic areas. A direct application may dismiss local conditions, materials, and construction practices. This study aimed to adapt construction details for bioretention to Finnish local practices and conditions and to formulate bioretention constructions that balance water, soil, and vegetation. First, construction details were reviewed, then local adaptations were applied, and finally, the application and two variations of growing media in two construction depths were tested in a test field in Southern Finland. Sandy growing media allowed the efficient retention of water during the first year, but failed to provide vital growth. The use of topsoil and compost in the growing media improved growth, but held high electrical conductivity after infiltration. All the experimental cells in the test field showed activity during the melting periods, both during winter and spring. If bioretention plays a multifunctional role in urban design and engineered ecology, the design parameters should not only focus on storm water quantity, but also on quality management and vegetation growth.

The Devil Is in the Details: Evidence from the GED on the Role of Examination System Details in Determining Who Passes. NCSALL Reports #16.

Science.gov (United States)

Tyler, John H.; Murnane, Richard J.; Willett, John B.

A study used data from a long-standing examination system, the General Educational Development (GED) certificate, to illustrate that the details of examination systems have marked impacts on the number of test takers who obtain the desired credential and on the racial/ethnic composition of passers. Data provided by the Florida Department of…

Increased interestingness of extraneous details in a multimedia science presentation leads to decreased learning.

Science.gov (United States)

Mayer, Richard E; Griffith, Emily; Jurkowitz, Ilana T N; Rothman, Daniel

2008-12-01

In Experiment 1, students received an illustrated booklet, PowerPoint presentation, or narrated animation that explained 6 steps in how a cold virus infects the human body. The material included 6 high-interest details mainly about the role of viruses in sex or death (high group) or 6 low-interest details consisting of facts and health tips about viruses (low group). The low group outperformed the high group across all 3 media on a subsequent test of problem-solving transfer (d = .80) but not retention (d = .05). In Experiment 2, students who studied a PowerPoint lesson explaining the steps in how digestion works performed better on a problem-solving transfer test if the lesson contained 7 low-interest details rather than 7 high-interest details (d = .86), but the groups did not differ on retention (d = .26). In both experiments, as the interestingness of details was increased, student understanding decreased (as measured by transfer). Results are consistent with a cognitive theory of multimedia learning, in which highly interesting details sap processing capacity away from deeper cognitive processing of the core material during learning. PsycINFO Database Record (c) 2008 APA, all rights reserved.

A Study on the construction of 22.9 kV distribution test line of KEPCO

Energy Technology Data Exchange (ETDEWEB)

Yang, Hi Kyun; Choi, Hung Sik; Hwang, Si Dole; Jung, Young Ho [Korea Electric Power Corp. (KEPCO), Taejon (Korea, Republic of). Research Center; Kim, Dong Hwan; Choi, Chang Huk [Korea Power Engineering Company and Architecture Engineers (Korea, Republic of)

1995-12-31

In order to enhance the reliability of power supply and the quality of electricity, a study on the construction of 22.9 kV distribution test line was performed. The main objective of this study was to establish a construction plan and a basic design to perform the construction and the detailed design of the test line effectively. (author). 21 refs., 45 figs.

Effects of emotional context on memory for details: the role of attention.

Science.gov (United States)

Kim, Johann Sung-Cheul; Vossel, Gerhard; Gamer, Matthias

2013-01-01

It was repeatedly demonstrated that a negative emotional context enhances memory for central details while impairing memory for peripheral information. This trade-off effect is assumed to result from attentional processes: a negative context seems to narrow attention to central information at the expense of more peripheral details, thus causing the differential effects in memory. However, this explanation has rarely been tested and previous findings were partly inconclusive. For the present experiment 13 negative and 13 neutral naturalistic, thematically driven picture stories were constructed to test the trade-off effect in an ecologically more valid setting as compared to previous studies. During an incidental encoding phase, eye movements were recorded as an index of overt attention. In a subsequent recognition phase, memory for central and peripheral details occurring in the picture stories was tested. Explicit affective ratings and autonomic responses validated the induction of emotion during encoding. Consistent with the emotional trade-off effect on memory, encoding context differentially affected recognition of central and peripheral details. However, contrary to the common assumption, the emotional trade-off effect on memory was not mediated by attentional processes. By contrast, results suggest that the relevance of attentional processing for later recognition memory depends on the centrality of information and the emotional context but not their interaction. Thus, central information was remembered well even when fixated very briefly whereas memory for peripheral information depended more on overt attention at encoding. Moreover, the influence of overt attention on memory for central and peripheral details seems to be much lower for an arousing as compared to a neutral context.

WA uranium find under detailed study

International Nuclear Information System (INIS)

1987-01-01

Results of detailed geological surveys of CRA's Kintyre prospect in Western Australia have confirmed the presence of uranium in significant quantities with a number of features that make it promising for mining. The deposit is set in the remote Rudall River area, about 1,200 kilometres northeast of Perth. So far, probable ore reserves of 15,000 tonnes of U 3 O 8 and possible reserves of 15,000 tonnes have been identified and announced. Grades vary widely within a range of 1.5 to 4kg per tonne. The bulk of the ore body lies within 160 metres of the surface, which means it could be mined by open cut methods. The uranium mineralisation has been encountered in bands of pitchblende occurring as veins within the host rock. Current indications are that conventional acid/leach solvent extraction processes can be used to extract the uranium. The Kintyre deposit lies about 700 metres inside the northern boundary of Western Australia's Rudall River National Park. Exploration by CRA at the southern end of the park, in the vicinity of Mt. Cotton, has been halted temporarily. While the Kintyre geological results to date are most encouraging, studies are now being carried out to determine the commercial potential of the deposit

Revisiting the Seductive Details Effect in Multimedia Learning: Context-Dependency of Seductive Details

Science.gov (United States)

Ozdemir, Devrim; Doolittle, Peter

2015-01-01

The purpose of this study was to investigate the effects of context-dependency of seductive details on recall and transfer in multimedia learning environments. Seductive details were interesting yet irrelevant sentences in the instructional text. Two experiments were conducted. The purpose of Experiment 1 was to identify context-dependent and…

Detail design of test loop for FIV in fuel bundle and preliminary test

Energy Technology Data Exchange (ETDEWEB)

Sim, Woo Gunl; Lee, Wan Young; Kim, Sung Won [Hannam University, Taejeon (Korea)

2002-04-01

It is urgent to develop the analytical model for the structural/mechanical integrity of fuel rod. In general, it is not easy to develop a pure analytical model. Occasionally, experimental results have been utilized for the model.Because of this reason, it is required to design proper test loop. Using the optimized test loop, With the optimized test loop, the dynamic behaviour of the rod will be evaluated and the critical flow velocity, which the rod loses the stability in, will be measured for the design of the rod. To verify the integrity of the fuel rod, it is required to evaluate the dynamic behaviour and the critical flow velocity with the test loop. The test results will be utilized to the design of the rod. Generally, the rod has a ground vibration due to turbulence in wide range of flow velocity and the amplitude of vibration becomes larger by the resonance, in a range of the velocity where occurs vortex. The rod loses stability in critical flow velocity caused by fluid-elastic instability. For the purpose of the present work to perform the conceptional design of the test loop, it is necessary (1) to understand the mechanism of the flow-induced vibration and the related experimental coefficients, (2) to evaluate the existing test loops for improving the loop with design parameters and (3) to decide the design specifications of the major equipments of the loop. 35 refs., 14 figs., 4 tabs. (Author)

Massive Memory Revisited: Limitations on Storage Capacity for Object Details in Visual Long-Term Memory

Science.gov (United States)

Cunningham, Corbin A.; Yassa, Michael A.; Egeth, Howard E.

2015-01-01

Previous work suggests that visual long-term memory (VLTM) is highly detailed and has a massive capacity. However, memory performance is subject to the effects of the type of testing procedure used. The current study examines detail memory performance by probing the same memories within the same subjects, but using divergent probing methods. The…

Detailed design of the large-bore 8 T superconducting magnet for the NAFASSY test facility

Science.gov (United States)

Corato, V.; Affinito, L.; Anemona, A.; Besi Vetrella, U.; Di Zenobio, A.; Fiamozzi Zignani, C.; Freda, R.; Messina, G.; Muzzi, L.; Perrella, M.; Reccia, L.; Tomassetti, G.; Turtù, S.; della Corte, A.

2015-03-01

The ‘NAFASSY’ (NAtional FAcility for Superconducting SYstems) facility is designed to test wound conductor samples under high-field conditions at variable temperatures. Due to its unique features, it is reasonable to assume that in the near future NAFASSY will have a preeminent role at the international level in the qualification of long coiled cables in operative conditions. The magnetic system consists of a large warm bore background solenoid, made up of three series-connected grading sections obtained by winding three different Nb3Sn Cable-in-Conduit Conductors. Thanks to the financial support of the Italian Ministry for University and Research the low-field coil is currently under production. The design has been properly modified to allow the system to operate also as a stand-alone facility, with an inner bore diameter of 1144 mm. This magnet is able to provide about 7 T on its axis and about 8 T close to the insert inner radius, giving the possibility of performing a test relevant for large-sized NbTi or medium-field Nb3Sn conductors. The detailed design of the 8 T magnet, including the electro-magnetic, structural and thermo-hydraulic analysis, is here reported, as well as the production status.

Author Details

African Journals Online (AJOL)

Development of a trap to contaminate variegated grasshoppers (Zonocerus variegatus L.) (Orthoptera: Pyrgomorphidae) with Metarrhyzium flavo-viride Gams & Rozsypal in the field. Details · Vol 40, No 1 (2007) - Articles Yam pests in the Ashanti and Brong Ahafo regions of Ghana: A study of farmers\\' indigenous technical ...

Author Details

African Journals Online (AJOL)

Geotechnical properties of lateritic soil developed over quartz schist in Ishara area, south western Nigeria Details · Vol 44, No 1 (2008) - Articles Comparative study of the influence of cement and lime stabilization on geotechnical properties of lateritic soil derived from pegmatite in Ago-Iwoye area, southwestern Nigeria

Author Details

African Journals Online (AJOL)

SAMA, G. Vol 2 (2002): Supplement - Articles A Longitudinal Study of the Role of T Cell subset, Th1/Th2 cytokines and antiplasmodial antibodies in uncomplicated Malaria in a Village Population Chronically Exposed to Plasmodium falciparum Malaria. Details PDF · AJOL African Journals Online. HOW TO USE AJOL.

Author Details

African Journals Online (AJOL)

KOUONTCHOU, Samuel. Vol 2 (2002): Supplement - Articles Prevalence of Multiple Concomitant Intestinal Parasitic Infections in Simbok a Malaria Endemic Village in Cameroon. Details PDF · Vol 2 (2002): Supplement - Articles A Longitudinal Study of the Role of T Cell subset, Th1/Th2 cytokines and antiplasmodial ...

Author Details

African Journals Online (AJOL)

ALAKE, J. Vol 2 (2002): Supplement - Articles A Longitudinal Study of the Role of T Cell subset, Th1/Th2 cytokines and antiplasmodial antibodies in uncomplicated Malaria in a Village Population Chronically Exposed to Plasmodium falciparum Malaria. Details PDF · AJOL African Journals Online. HOW TO USE AJOL.

Fabrication details for wire wrapped fuel assembly components

International Nuclear Information System (INIS)

Bosy, B.J.

1978-09-01

Extensive hydraulic testing of simulated LMFBR blanket and fuel assemblies is being carried out under this MIT program. The fabrication of these test assemblies has involved development of manufacturing procedures involving the wire wrapped pins and the flow housing. The procedures are described in detail in the report

Author Details

African Journals Online (AJOL)

Details PDF · Vol 22, No 2 (1999) - Articles Vegetation under different tree species in Acacia woodland in the Rift Valley of Ethiopia Details PDF · Vol 22, No 2 (1999) - Articles Preliminary evaluation of Phytomyza orobanchia (Diptera: Agromyzidae) as a controller of Orobanche spp in Ethiopia Details PDF. ISSN: 2520–7997.

Author Details

African Journals Online (AJOL)

QUAKYI, A.I.. Vol 2 (2002): Supplement - Articles A Longitudinal Study of the Role of T Cell subset, Th1/Th2 cytokines and antiplasmodial antibodies in uncomplicated Malaria in a Village Population Chronically Exposed to Plasmodium falciparum Malaria. Details PDF · AJOL African Journals Online. HOW TO USE AJOL.

Author Details

African Journals Online (AJOL)

Motabagani, MA. Vol 80, No 9 (2003): - Articles Anomalies of the renal, phrenic and suprarenal arteries: Case Report Details PDF · Vol 81, No 3 (2004): - Articles Morphological study of the uncommon rectus sterni muscle in German cadavers. Abstract PDF. ISSN: 0012-835X. AJOL African Journals Online. HOW TO USE ...

Important Details in Performing and Interpreting the Scratch Collapse Test.

Science.gov (United States)

Kahn, Lorna C; Yee, Andrew; Mackinnon, Susan E

2018-02-01

The utility of the scratch collapse test has been demonstrated in examination of patients with carpal and cubital tunnel syndromes and long thoracic and peroneal nerve compressions. In the authors' clinic, this lesser known test plays a key role in peripheral nerve examination where localization of the nerve irritation or injury is not fully understood. Test utility and accuracy in patients with more challenging presentations likely correlate with tester understanding and experience. This article offers a clear outline of all stages of the test to improve interrater reliability. The nuances of test performance are described, including a description of situations where the scratch collapse test is deemed inappropriate. Four clinical scenarios where the scratch collapse test may be useful are included. Corresponding video content is provided to improve performance and interpretation of the scratch collapse test. Diagnostic, V.

Detailed studies of a high-density polarized hydrogen gas target for storage rings

International Nuclear Information System (INIS)

Zapfe, K.; Brueckner, W.; Gaul, H.G.; Grieser, M.; Lin, M.T.; Moroz, Z.; Povh, B.; Rall, M.; Stechert, B.; Steffens, E.; Stenger, J.; Stock, F.; Tonhaeuser, J.; Montag, C.; Rathmann, F.; Fick, D.; Braun, B.; Graw, G.; Haeberli, W.

1996-01-01

A high-density target of polarized atomic hydrogen gas for applications in storage rings was produced by injecting atoms from an atomic beam source into a T-shaped storage cell. The influence of the internal gas target on electron-cooled beams of 27 MeV α-particles and 23 MeV protons in the Heidelberg Test Storage Ring has been studied in detail. Target polarization and target thickness were measured by means of 27 MeV α-particles. For hyperfine states 1+2 a target thickness of n=(0.96±0.04) x 10 14 H/cm 2 was achieved with the cell walls cooled to 100 K. Working with a weak magnetic holding field (∼5 G) the maximum target polarization was P T =0.84±0.02 when state 1 and P T =0.46±0.01 when states 1+2 were injected. The target polarization was found to be constant over a period of 3 months with a net charge of Q∼100 C passing the storage cell. (orig.)

Study of variables for accelerating lifetime testing of SOFCs

DEFF Research Database (Denmark)

Ploner, Alexandra; Hagen, Anke; Hauch, Anne

Solid oxide fuel cell (SOFC) applications require lifetimes of several years on the system level. A big challenge is to proof/confirm/demonstrate such exceptionally long lifetimes.Accelerated or compressed testing are possible methods. Activities in this area have been carried out without arriving...... at different current load cycling profiles revealed a strong deviation between predicted and measured lifetime [3].In this study, we present a detailed analysis of durability results for degradation mechanisms of single SOFC components as function of operating conditions. Electrochemical impedance data...

A detailed spectroscopic study of an Italian fresco

International Nuclear Information System (INIS)

Barilaro, Donatella; Crupi, Vincenza; Majolino, Domenico; Barone, Germana; Ponterio, Rosina

2005-01-01

In the present work we characterized samples of plasters and pictorial layers taken from a fresco in the Acireale Cathedral. The fresco represents the Coronation of Saint Venera, patron saint of this Ionian town. By performing a detailed spectroscopic analysis of the plaster preparation layer by Fourier-transform infrared (FTIR) spectroscopy and x-ray diffraction (XRD), and of the painting layer by FTIR and confocal Raman microspectroscopy, scanning electron microscopy+energy dispersive x-ray spectroscopy, and XRD, we were able to identify the pigments and the binders present. In particular, Raman investigation was crucial to the characterization of the pigments thanks to the high resolution of the confocal apparatus used. It is worth stressing that the simultaneous use of complementary techniques was able to provide more complete information for the conservation of the artifact we studied

Clinical professional governance for detailed clinical models.

Science.gov (United States)

Goossen, William; Goossen-Baremans, Anneke

2013-01-01

This chapter describes the need for Detailed Clinical Models for contemporary Electronic Health Systems, data exchange and data reuse. It starts with an explanation of the components related to Detailed Clinical Models with a brief summary of knowledge representation, including terminologies representing clinic relevant "things" in the real world, and information models that abstract these in order to let computers process data about these things. Next, Detailed Clinical Models are defined and their purpose is described. It builds on existing developments around the world and accumulates in current work to create a technical specification at the level of the International Standards Organization. The core components of properly expressed Detailed Clinical Models are illustrated, including clinical knowledge and context, data element specification, code bindings to terminologies and meta-information about authors, versioning among others. Detailed Clinical Models to date are heavily based on user requirements and specify the conceptual and logical levels of modelling. It is not precise enough for specific implementations, which requires an additional step. However, this allows Detailed Clinical Models to serve as specifications for many different kinds of implementations. Examples of Detailed Clinical Models are presented both in text and in Unified Modelling Language. Detailed Clinical Models can be positioned in health information architectures, where they serve at the most detailed granular level. The chapter ends with examples of projects that create and deploy Detailed Clinical Models. All have in common that they can often reuse materials from earlier projects, and that strict governance of these models is essential to use them safely in health care information and communication technology. Clinical validation is one point of such governance, and model testing another. The Plan Do Check Act cycle can be applied for governance of Detailed Clinical Models

Recent results of seismic isolation study in CRIEPI: Tests on seismic isolation elements, vibration tests and observations

International Nuclear Information System (INIS)

Ishida, Katsuhiko; Shiojiri, Hiroo; Mazda, Taiji; Ohtori, Yasuki; Aoyagi, Sakae

1992-01-01

Seismic isolation is expected to be effective in raising reliability during earthquake, reducing cost, enlarging and promoting the design standardization of electric power facilities. In Japan, it has been applied to several buildings. However it is considered that more research is needed to verify the reliability and effectiveness of seismic isolation for fast breeder reactors. In the preliminary study of isolation concepts for FBRs the horizontal base isolation of buildings was investigated in detail. The laminated rubber bearings were considered to be most suitable isolation system. Tests on large scale models of rubber bearing and vibration test of base isolation system have been conducted as well as the earthquake response observation of isolated buildings were conducted

Recent results of seismic isolation study in CRIEPI: Tests on seismic isolation elements, vibration tests and observations

Energy Technology Data Exchange (ETDEWEB)

Ishida, Katsuhiko; Shiojiri, Hiroo; Mazda, Taiji; Ohtori, Yasuki [Abiko Research Laboratory, Central Research Institute of Electric Power Industry (Japan); Aoyagi, Sakae [Central Research Institute of Electric Power Industry (Japan)

1992-07-01

Seismic isolation is expected to be effective in raising reliability during earthquake, reducing cost, enlarging and promoting the design standardization of electric power facilities. In Japan, it has been applied to several buildings. However it is considered that more research is needed to verify the reliability and effectiveness of seismic isolation for fast breeder reactors. In the preliminary study of isolation concepts for FBRs the horizontal base isolation of buildings was investigated in detail. The laminated rubber bearings were considered to be most suitable isolation system. Tests on large scale models of rubber bearing and vibration test of base isolation system have been conducted as well as the earthquake response observation of isolated buildings were conducted.

Author Details

African Journals Online (AJOL)

EKPA, O. D.. Vol 7, No 2 (2001) - Articles Variental differences AND polymorphism in palm oil: a case study of palm oils blended with coconut oil. Details PDF. ISSN: 1118-0579. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners ...

Minute Impurities Contribute Significantly to Olfactory Receptor Ligand Studies: Tales from Testing the Vibration Theory

OpenAIRE

Paoli, M.; M?nch, D.; Haase, A.; Skoulakis, E.; Turin, L.; Galizia, C. G.

2017-01-01

Several studies have attempted to test the vibrational hypothesis of odorant receptor activation in behavioral and physiological studies using deuterated compounds as odorants. The results have been mixed. Here, we attempted to test how deuterated compounds activate odorant receptors using calcium imaging of the fruit fly antennal lobe. We found specific activation of one area of the antennal lobe corresponding to inputs from a specific receptor. However, upon more detailed analysis, we disco...

Detailed GEANT description of the SDC central calorimeters

International Nuclear Information System (INIS)

Glagolev, V.V.; Li, W.

1994-01-01

This article represents the very detailed simulation model of the SDC central calorimeters and some results which were obtained using that model. The central calorimeters structure was coded on the GEANT 3.15 base in the frame of the SDCSIM environment. The SDCSIM is the general shell for simulation of the SDC set-up. The calorimeters geometry has been coded according to the FNAL and ANL engineering drawings and engineering data file. SDC central calorimeters detailed description is extremely useful for different simulation tasks, for fast simulation program parameters tuning, for different geometry especially studying (local response nonuniformity from bulkheads in the e.m. calorimeter and from coil supports and many others) and for the interpretation of the experimental data from the calorimeters. This simulation model is very useful for tasks of the test beam modules calorimeter calibration and for calorimeter in situ calibration. 3 refs., 8 figs

Detailed Studies of the Sculptor Dwarf Spheroidal Galaxy in the Milky Way halo

NARCIS (Netherlands)

Tolstoy, Eline

In and around the Milky Way halo there are a number of low mass low luminosity dwarf galaxies. Several of these systems have been studied in great detail. I describe recent photometric and spectroscopic studies of the Sculptor dwarf spheroidal galaxy made as part of the DART survey of nearby dwarf

A study of operational and testing reliability in software reliability analysis

International Nuclear Information System (INIS)

Yang, B.; Xie, M.

2000-01-01

Software reliability is an important aspect of any complex equipment today. Software reliability is usually estimated based on reliability models such as nonhomogeneous Poisson process (NHPP) models. Software systems are improving in testing phase, while it normally does not change in operational phase. Depending on whether the reliability is to be predicted for testing phase or operation phase, different measure should be used. In this paper, two different reliability concepts, namely, the operational reliability and the testing reliability, are clarified and studied in detail. These concepts have been mixed up or even misused in some existing literature. Using different reliability concept will lead to different reliability values obtained and it will further lead to different reliability-based decisions made. The difference of the estimated reliabilities is studied and the effect on the optimal release time is investigated

Detailed Modeling of Distillation Technologies for Closed-Loop Water Recovery Systems

Science.gov (United States)

Allada, Rama Kumar; Lange, Kevin E.; Anderson, Molly S.

2011-01-01

Detailed chemical process simulations are a useful tool in designing and optimizing complex systems and architectures for human life support. Dynamic and steady-state models of these systems help contrast the interactions of various operating parameters and hardware designs, which become extremely useful in trade-study analyses. NASA?s Exploration Life Support technology development project recently made use of such models to compliment a series of tests on different waste water distillation systems. This paper presents efforts to develop chemical process simulations for three technologies: the Cascade Distillation System (CDS), the Vapor Compression Distillation (VCD) system and the Wiped-Film Rotating Disk (WFRD) using the Aspen Custom Modeler and Aspen Plus process simulation tools. The paper discusses system design, modeling details, and modeling results for each technology and presents some comparisons between the model results and recent test data. Following these initial comparisons, some general conclusions and forward work are discussed.

Research and development studies on the seismic behaviour of the PEC fast reactor (safety analysis detailed report no. 8)

Energy Technology Data Exchange (ETDEWEB)

Martelli, A.; Forni, M.; Masoni, P.; Maresca, G.; Castoldi, A.; Muzzi, F. [ENEA, Rome (Italy); Ansaldo Spa, Genoa [Italy; ISMES Spa, Bergamo [Italy

1988-01-15

This paper presents the main features and results of the numerical and experimental studies that were carried out by ENEA (Italian Commission for Alternative Energy Sources) for the seismic verification of the Italian PEC fast reactor test facility. More precisely, the paper focuses on the wide-ranging research and development programme that has been performed (and recently completed) on the reactor building, the reactor-block, the main vessel, the core and the shutdown system. The needs of these detailed studies are stressed and the feed-backs on the design, necessary safisfy the seismic safety requirements, are recalled. The general validity of the analyses in the framework of the research and development activities for nuclear reactor is also pointed out.

Study on detailed geological modelling for fluvial sandstone reservoir in Daqing oil field

Energy Technology Data Exchange (ETDEWEB)

Zhao Hanqing; Fu Zhiguo; Lu Xiaoguang [Institute of Petroleum Exploration and Development, Daqing (China)

1997-08-01

Guided by the sedimentation theory and knowledge of modern and ancient fluvial deposition and utilizing the abundant information of sedimentary series, microfacies type and petrophysical parameters from well logging curves of close spaced thousands of wells located in a large area. A new method for establishing detailed sedimentation and permeability distribution models for fluvial reservoirs have been developed successfully. This study aimed at the geometry and internal architecture of sandbodies, in accordance to their hierarchical levels of heterogeneity and building up sedimentation and permeability distribution models of fluvial reservoirs, describing the reservoir heterogeneity on the light of the river sedimentary rules. The results and methods obtained in outcrop and modem sedimentation studies have successfully supported the study. Taking advantage of this method, the major producing layers (PI{sub 1-2}), which have been considered as heterogeneous and thick fluvial reservoirs extending widely in lateral are researched in detail. These layers are subdivided into single sedimentary units vertically and the microfacies are identified horizontally. Furthermore, a complex system is recognized according to their hierarchical levels from large to small, meander belt, single channel sandbody, meander scroll, point bar, and lateral accretion bodies of point bar. The achieved results improved the description of areal distribution of point bar sandbodies, provide an accurate and detailed framework model for establishing high resolution predicting model. By using geostatistic technique, it also plays an important role in searching for enriched zone of residual oil distribution.

Studies of the steam generator degraded tubes behavior on BRUTUS test loop

Energy Technology Data Exchange (ETDEWEB)

Chedeau, C.; Rassineux, B. [EDF/DER/MTC, Moret Sur Loing (France); Flesch, B. [EDF/EPN/DMAINT, Paris (France)] [and others

1997-04-01

Studies for the evaluation of steam generator tube bundle cracks in PWR power plants are described. Global tests of crack leak rates and numerical calculations of crack opening area are discussed in some detail. A brief overview of thermohydraulic studies and the development of a mechanical probabilistic design code is also given. The COMPROMIS computer code was used in the studies to quantify the influence of in-service inspections and maintenance work on the risk of a steam generator tube rupture.

Testing geopressured geothermal reservoirs in existing wells: Detailed completion prognosis for geopressured-geothermal well of opportunity, prospect #7

Energy Technology Data Exchange (ETDEWEB)

Godchaux, Frank A.

1981-06-01

This book is a detailed prognosis covering the acquisition, completion, drilling, testing and abandonment of the Frank A. Godchaux, III, Well No. 1 under the Wells of Opportunity Program. The well is located approximately 12 miles southeast of the city of Abbeville, Louisiana. Eaton Operating Company proposes to test a section of the Planulina sand at a depth ranging from 15,584 to 15,692 feet. The reservoir pressure is estimated to be 14,480 psi and the temperature of the formation water is expected to be 298 F. The water salinity is calculated to be 75,000 ppm. The well is expected to produce 20,000 barrels of water per day with a gas content of 44 standard cubic feet pre barrel. The well was acquired from C and K Petroleu, Inc. on March 20, 1981. C and K abandoned the well at a total depth of 16,000 feet. The well has a 7-5/8 inches liner set at 13,387 feet. Eaton proposes to set 5-1/2 inch casing at 16,000 feet and produce the well through the casing using a 2-3/8 inch tubing string for wireline protection and for pressure control. A 4,600 foot saltwater disposal well will be drilled on the site and testing will be conducted similar to previous Eaton tests. The total estimated cost to perform the work is $2,959,000. An optional test from 14,905 to 15,006 feet may be performed after the original test and will require a workover with a rig on location to perform the plugback. The surface production equipment utilized on previous Eaton WOO tests will be utilized on this test. This equipment has worked satisfactorily and all parties involved in the testing are familiar with its operation. The Institute of Gas Technology and Mr. Don Clark will handle the sampling and testing and reservoir evaluation, respectively, as on the previous Eaton tests.

Cost model relationships between textile manufacturing processes and design details for transport fuselage elements

Science.gov (United States)

Metschan, Stephen L.; Wilden, Kurtis S.; Sharpless, Garrett C.; Andelman, Rich M.

1993-01-01

Textile manufacturing processes offer potential cost and weight advantages over traditional composite materials and processes for transport fuselage elements. In the current study, design cost modeling relationships between textile processes and element design details were developed. Such relationships are expected to help future aircraft designers to make timely decisions on the effect of design details and overall configurations on textile fabrication costs. The fundamental advantage of a design cost model is to insure that the element design is cost effective for the intended process. Trade studies on the effects of processing parameters also help to optimize the manufacturing steps for a particular structural element. Two methods of analyzing design detail/process cost relationships developed for the design cost model were pursued in the current study. The first makes use of existing databases and alternative cost modeling methods (e.g. detailed estimating). The second compares design cost model predictions with data collected during the fabrication of seven foot circumferential frames for ATCAS crown test panels. The process used in this case involves 2D dry braiding and resin transfer molding of curved 'J' cross section frame members having design details characteristic of the baseline ATCAS crown design.

[Comparison of film-screen combination in a contrast detail diagram and with interactive image analysis. 1: Contrast detail diagram].

Science.gov (United States)

Hagemann, G; Eichbaum, G

1997-07-01

The following three film-screen combinations were compared: a) a combination of anticrossover film and UV-light emitting screens, b) a combination of blue-light emitting screens and film, and c) a conventional green fluorescing screen film combination. Radiographs of a specially designed plexiglass phantom (0.2 x 0.2 x 0.12 m3) were obtained that contained bar patterns of lead and plaster (calcium sulfate) to test high and intermediate contrast resolution and bar patterns of air to test low contrast resolution, respectively. An aluminum step wedge was integrated to evaluate dose-density curves of the radiographs. The dose values for the various step thicknesses were measured as percentage of the dose value in air for 60, 81, and 117 kV. Exposure conditions were the following: 12 pulse generator, 0.6 mm focus size, 4.7 mm aluminum prefilter, a grid with 40 lines/cm (12:1), and a focus-detector distance of 1.15 m. The thresholds of visible bars of the various pattern materials were assessed by seven radiologists, one technician, and the authors. The resulting contrast detail diagram could not prove any significant differences between the three tested screen film combinations. The pairwise comparison, however, found 8 of the 18 paired differences to be statistically significant between the conventional and the two new screen-film combinations. The authors concluded that subjective visual assessment of the threshold in a contrast detail study alone is of only limited value to grade image quality if no well-defined criteria are used (BIR report 20 [1989] 137-139). The statistical approach of paired differences of the estimated means appeared to be more appropriate.

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... An algorithm to retrieve Land Surface Temperature using Landsat-8 Dataset Abstract PDF. ISSN: 2225-8531.

Studies on mechanical properties, microstructure and fracture morphology details of laser beam welded thick SS304L plates for fusion reactor applications

Energy Technology Data Exchange (ETDEWEB)

Buddu, Ramesh Kumar, E-mail: buddu@ipr.res.in [Fusion Reactor Materials Development and Characterization Division, Institute for Plasma Research, Bhat, Gandhinagar 382428 (India); Chauhan, N.; Raole, P.M. [Fusion Reactor Materials Development and Characterization Division, Institute for Plasma Research, Bhat, Gandhinagar 382428 (India); Natu, Harshad [Magod Laser Machining Pvt. Ltd, Jigani, Bengaluru 560105 (India)

2015-06-15

Highlights: • CO{sub 2} laser welding of 8 mm thick SS304L plates has been carried out and full penetration welds fabricated and characterized for mechanical properties and microstructure details. • Welded samples have shown tensile properties comparable to base indicating good weld quality joints. • Impact fracture tests of weld zone and heat affected zone samples have shown poor toughness compared to the base metal. • SEM analysis of fracture samples of tensile and impact specimens indicated the complex microstructure features in weld zone and combined ductile and brittle fracture features. • Combined features of dendrite and cellular structures are observed in weld microstructures with narrow HAZ and delta ferrite is found in the welds and further confirmed by higher Ferrite Number data. - Abstract: Austenitic stainless steel is widely used structural material for the fabrication of the fusion reactor components. Laser welding is high power density process which offers several advantages over the other conventional processes like Tungsten Inert Gas welding. The features like low distortion, narrow heat affected zone, deep penetration in single pass, good mechanical properties are some of the advantages of laser welding process. The laser weld process parameters optimization has several challenges in terms of overcoming the weld defects like voids due to lack of penetration over depth, undercuts and porosity. The present paper reports the studies carried out with CO{sub 2} laser welding of 8 mm thick austenitic stainless steel SS304L plates and their characterization of mechanical properties, microstructure and fracture morphology details. The weld process parameter optimization towards defect free welds with full penetration welding has been carried out. The welded samples have shown tensile properties comparable to base metal, bend tests are successfully passed. The hardness measurements have shown slightly higher for weld zone compared to base metal

Studies on mechanical properties, microstructure and fracture morphology details of laser beam welded thick SS304L plates for fusion reactor applications

International Nuclear Information System (INIS)

Buddu, Ramesh Kumar; Chauhan, N.; Raole, P.M.; Natu, Harshad

2015-01-01

Highlights: • CO 2 laser welding of 8 mm thick SS304L plates has been carried out and full penetration welds fabricated and characterized for mechanical properties and microstructure details. • Welded samples have shown tensile properties comparable to base indicating good weld quality joints. • Impact fracture tests of weld zone and heat affected zone samples have shown poor toughness compared to the base metal. • SEM analysis of fracture samples of tensile and impact specimens indicated the complex microstructure features in weld zone and combined ductile and brittle fracture features. • Combined features of dendrite and cellular structures are observed in weld microstructures with narrow HAZ and delta ferrite is found in the welds and further confirmed by higher Ferrite Number data. - Abstract: Austenitic stainless steel is widely used structural material for the fabrication of the fusion reactor components. Laser welding is high power density process which offers several advantages over the other conventional processes like Tungsten Inert Gas welding. The features like low distortion, narrow heat affected zone, deep penetration in single pass, good mechanical properties are some of the advantages of laser welding process. The laser weld process parameters optimization has several challenges in terms of overcoming the weld defects like voids due to lack of penetration over depth, undercuts and porosity. The present paper reports the studies carried out with CO 2 laser welding of 8 mm thick austenitic stainless steel SS304L plates and their characterization of mechanical properties, microstructure and fracture morphology details. The weld process parameter optimization towards defect free welds with full penetration welding has been carried out. The welded samples have shown tensile properties comparable to base metal, bend tests are successfully passed. The hardness measurements have shown slightly higher for weld zone compared to base metal and the

A Detailed Study of Rocky Planetary Material in the Hyades

Science.gov (United States)

Farihi, Jay

2017-08-01

The Hyades is the nearest open cluster, relatively young, and containing numerous A-type stars. Its youth, distance, and metallicity make it an ideal site to study planet formation around 2-3 Msun stars, and in a dynamically challenging environment.During our HST COS Snapshot, we discovered the ongoing accretion of Si-rich and C-deficient material in two white dwarf Hyads. The lower limit Si/C ratios determined from these 400s exposures indicate the material is more C-depleted than in chondritic meteorites, the most primitive rocks in the Solar System. Our 2013 Keck discovery of metal pollution in a third Hyades white dwarf indicates that planet formation is common in the cluster. Together, these three stars indicate that substantial minor bodies persist at several AU or more, and provide an unprecedented opportunity for a detailed study of rocky exoplanet precursors in a cluster environment.We propose to obtain detailed abundances of the planetary debris at these three polluted Hyads, which requires a modest investment of observatory time. The mass ratios between C, O, Mg, and Si are accurate indicators of the temperature and orbital regions where the parent bodies formed, their water and volatile contents. We will also detect Al and Fe, which are key indicators of differentiation and giant impacts among planetary embryos.Our proposed observations will provide legacy value for planet formation models, and especially those in cluster enviroments. These observations cannot be done from the ground or at optical or longer wavelengths, and must be carried out by HST in the ultraviolet.

Main: Clone Detail [KOME

Lifescience Database Archive (English)

Full Text Available Clone Detail Mapping Pseudomolecule data detail Detail information Mapping to the T...IGR japonica Pseudomolecules kome_mapping_pseudomolecule_data_detail.zip kome_mapping_pseudomolecule_data_detail ...

Using VIS/NIR and IR spectral cameras for detecting and separating crime scene details

Science.gov (United States)

Kuula, Jaana; Pölönen, Ilkka; Puupponen, Hannu-Heikki; Selander, Tuomas; Reinikainen, Tapani; Kalenius, Tapani; Saari, Heikki

2012-06-01

Detecting invisible details and separating mixed evidence is critical for forensic inspection. If this can be done reliably and fast at the crime scene, irrelevant objects do not require further examination at the laboratory. This will speed up the inspection process and release resources for other critical tasks. This article reports on tests which have been carried out at the University of Jyväskylä in Finland together with the Central Finland Police Department and the National Bureau of Investigation for detecting and separating forensic details with hyperspectral technology. In the tests evidence was sought after at an assumed violent burglary scene with the use of VTT's 500-900 nm wavelength VNIR camera, Specim's 400- 1000 nm VNIR camera, and Specim's 1000-2500 nm SWIR camera. The tested details were dried blood on a ceramic plate, a stain of four types of mixed and absorbed blood, and blood which had been washed off a table. Other examined details included untreated latent fingerprints, gunshot residue, primer residue, and layered paint on small pieces of wood. All cameras could detect visible details and separate mixed paint. The SWIR camera could also separate four types of human and animal blood which were mixed in the same stain and absorbed into a fabric. None of the cameras could however detect primer residue, untreated latent fingerprints, or blood that had been washed off. The results are encouraging and indicate the need for further studies. The results also emphasize the importance of creating optimal imaging conditions into the crime scene for each kind of subjects and backgrounds.

Author Details

African Journals Online (AJOL)

PROMOTING ACCESS TO AFRICAN RESEARCH. AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search · USING AJOL · RESOURCES. Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads.

Kinetics of ethylcyclohexane pyrolysis and oxidation: An experimental and detailed kinetic modeling study

KAUST Repository

Wang, Zhandong; Zhao, Long; Wang, Yu; Bian, Huiting; Zhang, Lidong; Zhang, Feng; Li, Yuyang; Sarathy, Mani; Qi, Fei

2015-01-01

species were evaluated, and good agreement was observed between the PIMS and GC data sets. Furthermore, a fuel-rich burner-stabilized laminar premixed ECH/O2/Ar flame at 30Torr was studied using synchrotron VUV PIMS. A detailed kinetic model for ECH high

Table 1. Details of Archaea considered for this study. P hylum Name ...

Indian Academy of Sciences (India)

User

Table 1. Details of Archaea considered for this study. P hylum. Name. Genome G+. C. %. *. G enome. S ize. *. Gene count. *. Max growth temp. (oC). Optimum growth temp (oC). Generation time, tg. (min). ttR. NA. #. dtR. NA. #. Source. †. 1. C renarchaeota. Aeropyrum pernix K1. 56.31 1669696 1752 100 90-95. 200. 42. 42.

Author Details

African Journals Online (AJOL)

An Overview of Africa's Marine Resources: Their Utilization and Sustainable Management Details · Vol 12, No 3 (2000) - Articles EDITORIAL Ganoderma Lucidum - Paramount among Medicinal Mushrooms. Details · Vol 15, No 3 (2003) - Articles Editorial: Africa's Mushrooms: A neglected bioresource whose time has come

Massive memory revisited: Limitations on storage capacity for object details in visual long-term memory

OpenAIRE

Cunningham, Corbin A.; Yassa, Michael A.; Egeth, Howard E.

2015-01-01

Previous work suggests that visual long-term memory (VLTM) is highly detailed and has a massive capacity. However, memory performance is subject to the effects of the type of testing procedure used. The current study examines detail memory performance by probing the same memories within the same subjects, but using divergent probing methods. The results reveal that while VLTM representations are typically sufficient to support performance when the procedure probes gist-based information, they...

ROOT Analysis of 2004 H8 Test Beam Data & Studies of MDT Sense Wire Displacements

CERN Document Server

2004-01-01

Tests are being carried out at the CERN H8 Test Facility on the subdetectors of ATLAS. Using MUTRAK, a tool developed by Dan Levin, data from test muon beam runs are converted to PAW plots and ntuples for easy analysis. ROOT classes are currently being developed to convert the PAW output of MUTRAK to ROOT files for more detailed analysis. Also studies are currently underway to understand the effect of sense wire displacements in Monitored Drift Tubes on drift time spectra. Concurrent tests using simulations in GARFIELD and Cosmic Ray MDT experiments are underway to study wire sags which may be up to 480 micrometers due to gravitational and electrostatic forces .

A detailed family history of myocardial infarction and risk of myocardial infarction

DEFF Research Database (Denmark)

Ranthe, Mattis Flyvholm; Petersen, Jonathan Aavang; Bundgård, Henning

2015-01-01

of cardiovascular medications. CONCLUSION: A detailed family history, particularly number of affected first- and second-degree relatives, contributes meaningfully to risk assessment, especially in middle-aged persons. Future studies should test for potential improvement of risk algorithm prediction using detailed......BACKGROUND: Family history of myocardial infarction (MI) is an independent risk factor for MI. Several genetic variants are associated with increased risk of MI and family history of MI in a first-degree relative doubles MI risk. However, although family history of MI is not a simple dichotomous...... risk factor, the impact of specific, detailed family histories has not received much attention, despite its high clinical relevance. We examined risk of MI by MIs in first- and second-degree relatives and by number and age of affected relatives. METHODS AND FINDINGS: Using Danish national registers, we...

Wooden houses in detail. Holzhaeuser im Detail

Energy Technology Data Exchange (ETDEWEB)

Ruske, W. (ed.)

1986-01-01

Under the serial title 'Planning and construction of wooden houses', WEKA will publish a number of books of which this is the first. Details of design and construction are presented, e.g.: Details of modern one-family houses; Fundamentals of design and hints for planning of wooden houses and compact wooden structures; Constructional ecology, wood protection, thermal insulation, sound insulation; Modular systems for domestic buildings; The 'bookshelf-type' house at the Berlin International Construction Exhibition (IBA); Experience with do-it-yourself systems. With 439 figs.

Phase Behavior of a Phospholipid/Fatty Acid/Water Mixture Studied in Atomic Detail

NARCIS (Netherlands)

Knecht, Volker; Mark, Alan E.; Marrink, Siewert-Jan

2006-01-01

Molecular dynamics simulations have been used to study the phase behavior of a dipalmitoylphosphatidylcholine (DPPC)/palmitic acid (PA)/water 1:2:20 mixture in atomic detail. Starting from a random solution of DPPC and PA in water, the system adopts either a gel phase at temperatures below similar

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Singh, J. Vol 3, No 2 (2011) - Articles Plane waves in a rotating generalized thermo-elastic solid with voids. Abstract PDF. ISSN: 2141-2839. AJOL African Journals Online. HOW TO USE AJOL.

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Vol 12 (2008) - Articles On the wave equations of shallow water with rough bottom topography. Abstract · Vol 14 (2009) - Articles Energy generation in a plant due to variable sunlight intensity

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Vol 45 (2016) - Articles From vectors to waves and streams: An alternative approach to semantic maps1. Abstract PDF · Vol 48 (2017) - Articles Introduction: 'n Klein ietsie for Johan Oosthuizen

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... to blast loadings. Abstract PDF · Vol 9, No 3S (2017): Special Issue - Articles Experimental and numerical investigation on blast wave propagation in soil structure. Abstract PDF. ISSN: 1112-9867.

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Iliopsoas haematoma in a rugby player. Abstract PDF · Vol 29, No 1 (2017) - Articles The use of negative pressure wave treatment in athlete recovery. Abstract PDF. ISSN: 2078-516X. AJOL African ...

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... No 3S (2017): Special Issue - Articles Experimental and numerical investigation on blast wave propagation in soil structure. Abstract PDF · Vol 9, No 3S (2017): Special Issue - Articles Simulation on ...

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Duwa, S S. Vol 8 (2004) - Articles Lower hybrid waves instability in a velocity–sheared inhomogenous charged dust beam. Abstract · Vol 9 (2005) - Articles The slide away theory of lower hybrid bursts

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... The use of negative pressure wave treatment in athlete recovery. Abstract PDF · Vol 29, No 1 (2017) - Articles The prevalence, risk factors predicting injury and the severity of injuries sustained during ...

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Vol 29, No 1 (2017) - Articles The use of negative pressure wave treatment in athlete recovery. Abstract PDF · Vol 29, No 1 (2017) - Articles The prevalence, risk factors predicting injury and the ...

Evaluation of outgassing, tear strength, and detail reproduction in alginate substitute materials.

Science.gov (United States)

Baxter, R T; Lawson, N C; Cakir, D; Beck, P; Ramp, L C; Burgess, J O

2012-01-01

To compare three alginate substitute materials to an alginate impression material for cast surface porosity (outgassing), tear strength, and detail reproduction. Detail reproduction tests were performed following American National Standards Institute/American Dental Association (ANSI/ADA) Specification No. 19. To measure tear strength, 12 samples of each material were made using a split mold, placed in a water bath until testing, and loaded in tension until failure at a rate of 500 mm/min using a universal testing machine. For cast surface porosity testing, five impressions of a Teflon mold with each material were placed in a water bath (37.8°C) for the in-mouth setting time and poured with vacuum-mixed Silky Rock die stone at 5, 10, 30, and 60 minutes from the start of mixing. The gypsum samples were analyzed with a digital microscope for surface porosity indicative of hydrogen gas release by comparing the surface obtained at each interval with four casts representing no, little, some, and significant porosity. Data analysis was performed using parametric and Kruskal-Wallis analysis of variance (ANOVA), Tukey/Kramer post-hoc tests (α=0.05), and individual Mann-Whitney U tests (α=0.0167). All alginate substitute materials passed the detail reproduction test. Tear strength of the alginate substitute materials was significantly better than alginate and formed three statistically different groups: AlgiNot had the lowest tear strength, Algin-X Ultra had the highest tear strength, and Position Penta Quick had intermediate tear strength. Significant variation in outgassing existed between materials and pouring times (palginate substitute materials exhibited the least outgassing and cast porosity 60 minutes after mixing. Detail reproduction and tear strength of alginate substitute materials were superior to traditional alginate. The outgassing effect was minimal for most materials tested. Alginate substitute materials are superior replacements for irreversible

118-B-1 excavation treatability test procedures

International Nuclear Information System (INIS)

Frain, J.M.

1994-01-01

This treatability study has two purposes: to support development of the approach to be used for burial ground remediation, and to provide specific engineering information for the design of burial grounds receiving waste generated from the 100 Area removal actions. Data generated from this test will also provide performance and cost information necessary for detailed analysis of alternatives for burial ground remediation. Further details on the test requirements, milestones and data quality objectives are described in detail in the 118-B-1 Excavation Treatability Test Plan (DOE/RL-94-43). These working procedures are intended for use by field personnel to implement the requirements of the milestone. A copy of the detailed Test Plan will be kept on file at the on-site field support trailer, and will be available for review by field personnel

Feasibility study of the Dragon reactor for HTGR fuel testing

International Nuclear Information System (INIS)

Wallroth, C.F.

1975-01-01

The Organization of European Community Development (OECD) Dragon high-temperature reactor project has performed HTGR fuel and fuel element testing for about 10 years. To date, a total of about 250 fuel elements have been irradiated and the test program continues. The feasibility of using this test facility for HTGR fuel testing, giving special consideration to U. S. needs, is evaluated. A detailed description for design, preparation, and data acquisition of a test experiment is given together with all possible options on supporting work, which could be carried out by the experienced Dragon project staff. 11 references. (U.S.)

Radionuclide migration studies at the Nevada Test Site

International Nuclear Information System (INIS)

Thompson, J.L.

1989-01-01

The United States government routinely tests nuclear devices at the Nevada Test Site (NTS) in southern Nevada. A significant amount of radioactive material exists underground at the NTS with no containers or engineered barriers to inhibit its subsequent migration. The Department of Energy has sponsored for many years a research program on radionuclide movement in the geologic media at this location. Goals of this research program are to measure the extent of movement of radionuclides away from underground explosion sites and to determine the mechanisms by which such movement occurs. This program has acquired significance in another aspect of nuclear waste management because of the Yucca Mountain Project. Yucca Mountain at the NTS is being intensively studied as the possible site for a mined repository for high level nuclear waste. The NTS provides a unique setting for field studies concerning radionuclide migration; there is the potential for greatly increasing our knowledge of the behavior of radioactive materials in volcanogenic media. This review summarizes some of the significant findings made under this research program at the NTS and identifies reports in which the details of the research may be found. 36 refs., 4 figs

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Isa, M.F.M.. Vol 9, No 3S (2017): Special Issue - Articles Experimental and numerical investigation on blast wave propagation in soil structure. Abstract PDF · Vol 9, No 3S (2017): Special Issue - ...

Polonium-210 in Euphauslids: A Detailed Study

International Nuclear Information System (INIS)

Heyraud, M.; Fowler, S.W.; Beasley, T.M.; Cherry, R.D.

1976-01-01

A detailed study of 210 Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. The purpose was to obtain information concerning the origin, the localization and the flux of the nuclide in and through this organism. Measurements of 210 Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of 210 Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of 210 Po through M. norvegica to be calculated. The calculations confirm that food is the principal sauce of 210 Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting 210 Po from the surface layers of the ocean to depth. (author)

Polonium-210 in euphausiids: a detailed study

Energy Technology Data Exchange (ETDEWEB)

Heyraud, M; Fowler, S W; Beasley, T M; Cherry, R D

1976-02-13

A detailed study of /sup 210/Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. Information was obtained concerning the origin, the localization and the flux of the nuclide in and through the organism. Measurements of /sup 210/Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of /sup 210/Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of /sup 210/Po through M. norvegica to be calculated. The calculations confirm that food is the principal source of /sup 210/Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting /sup 210/Po from the surface layers of the ocean to depth. (auth)

Status report. KfK contribution to the development of DEMO-relevant test blankets for NET/ITER. Pt. 1: Self-cooled liquid metal breeder blanket. Vol. 2. Detailed version

International Nuclear Information System (INIS)

John, H.; Malang, S.; Sebening, H.

1991-12-01

A self-cooled liquid metal breeder blanket for a fusion DEMO-reactor and the status of the development programme is described as a part of the European development programme of DEMO relevant test blankets for NET/ITER. Volume 1 (KfK 4907) contains a summary. Volume 2 (KfK 4908) a more detailed version of the report. Both volumes contain sections on previous studies on self-cooled liquid metal breeder blankets, the reference blanket design for a DEMO-reactor, a typical test blanket design including the ancillary loop system and the building requirements for NET/ITER together with the present status of the associated RandD-programme in the fields of neutronics, magnetohydrodynamics, tritium removal and recovery, liquid metal compatibility and purification, ancillary loop system, safety and reliability. An outlook is given regarding the required RandD-programme for the self-cooled liquid metal breeder blanket prior to tests in NET/ITER and the relevant test programme to be performed in NET/ITER. (orig.) [de

Thermal hydraulic studies in steam generator test facility

International Nuclear Information System (INIS)

Vinod, V.; Suresh Kumar, V.A.; Noushad, I.B.; Ellappan, T.R.; Rajan, K.K.; Rajan, M.; Vaidyanathan, G.

2005-01-01

Full text of publication follows: A 500 MWe fast breeder reactor is being constructed at Kalpakkam, India. This is a sodium cooled reactor with two primary and two secondary sodium loops with total 8 steam generators. The typical advantage of fast breeder plants is the high operating temperature of steam cycles and the high plant efficiency. To produce this high pressure and high temperature steam, once through straight tube vertical sodium heated steam generators are used. The steam is generated from the heat produced in the reactor core and being transported through primary and secondary sodium circuits. The steam generator is a 25 m high middle supported steam generator with expansion bend and 23 m heat transfer length. Steam Generator Test Facility (SGTF) constructed at Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam aims at performing various tests on a 5.5 MWt steam generator. This vertically simulated test article is similar in all respects to the proposed 157 MWt steam generator module for the Prototype Fast Breeder Reactor (PFBR), with reduced number of tubes. Heat transfer performance tests are done with this 19 tube steam generator at various load conditions. Sodium circuit for the SGTF is equipped with oil fired heater as heat source and centrifugal sodium pump, to pump sodium at 105 m 3 /hr flow rate. Other typical components like sodium to air heat exchanger, sodium purification system and hydrogen leak detection system is also present in the sodium circuit. High pressure steam produced in the steam generator is dumped in a condenser and recycled. Important tests planned in SGTF are the heat transfer performance test, stability test, endurance test and performance test of steam generator under various transients. The controlled operation of steam generator will be studied with possible control schemes. A steady state simulation of the steam generator is done with a mathematical model. This paper gives the details of heat transfer

Groundwater movements around a repository. Phase 1, State of the art and detailed study plan

International Nuclear Information System (INIS)

Lindblom, U.

1977-02-01

The report was prepared as the first phase of a study of the groundwater movements around a repository for spent nuclear fuel in the precambrian bedrock of Sweden. The objectives of these studies are to provide a state of the art review of groundwater slow in the region of a repository in granitic rock, in order to provide a basis for long term containment assessments and to prepare a detailed study plan for the continuation of the project. The different processes affecting the groundwater situation for containment are given. A state of the art review of the fluid flow, geochemical, heat transfer and rock mechanics processes as they relate to containment is presented. A detailed study plan to provide a comprehensive assessment of the hydrogeological regime around the repository during its lifetime is also presented. The groundwater flow fields will provide a basis for subsequent long term containment studies. (L.B.)

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Abstract PDF · Vol 3, No 6 (2011) - Articles Mixed convection flow and heat transfer in a vertical wavy channel containing porous and fluid layer with traveling thermal waves. Abstract PDF · Vol 3, No 8 ...

Author Details

African Journals Online (AJOL)

Author Details. Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Ismail, A. Vol 9, No 3S (2017): Special Issue - Articles Investigate of wave absorption performance for oil palm frond and empty fruit bunch at 5.8 GHz. Abstract PDF · Vol 9, No 3S (2017): Special Issue ...

Detailed Performance Study of ATLAS Endcap Muon Trigger with Beam Collision Data

CERN Document Server

Hayakawa, T

2010-01-01

In 2009 the first beam collision was occurred at the LHC and the ATLAS has started data taking with beam collision at s = 7 TeV since May 2010. This poster will mention the contraptions to take the beam collision data for the electronics of Level1 Endcap Muon Trigger system, and the result and detailed study of LVL1 Endcap Muon Trigger system performance with beam collision.

A detailed study of the generation of optically detectable watermarks using the logistic map

International Nuclear Information System (INIS)

Mooney, Aidan; Keating, John G.; Heffernan, Daniel M.

2006-01-01

A digital watermark is a visible, or preferably invisible, identification code that is permanently embedded in digital media, to prove owner authentication and provide protection for documents. Given the interest in watermark generation using chaotic functions a detailed study of one chaotic function for this purpose is performed. In this paper, we present an approach for the generation of watermarks using the logistic map. Using this function, in conjunction with seed management, it is possible to generate chaotic sequences that may be used to create highpass or lowpass digital watermarks. In this paper we provide a detailed study on the generation of optically detectable watermarks and we provide some guidelines on successful chaotic watermark generation using the logistic map, and show using a recently published scheme, how care must be taken in the selection of the function seed

A new debate for Turkish physicians: e-detailing.

Science.gov (United States)

Ventura, Keti; Baybars, Miray; Dedeoglu, Ayla Ozhan

2012-01-01

The study presents an empirical analysis of the attitudes of Turkish physicians towards e-detailing practices compared to face-to-face detailing. The findings reveal that although physicians have positive attitudes toward e-detailing, on some points they are still undecided and/or have doubts. The structural model revealed that affect, convenience, and informative content influence their attitude in a positive manner, whereas the personal interaction was found to be a negative factor. Physicians' age and frequency of calls received from representatives are moderators. The present study can be seen as an addition to pharmaceutical marketing, an underresearched study field in Turkey, and e-detailing particularly.

Kinetics of ethylcyclohexane pyrolysis and oxidation: An experimental and detailed kinetic modeling study

KAUST Repository

Wang, Zhandong

2015-07-01

Ethylcyclohexane (ECH) is a model compound for cycloalkanes with long alkyl side-chains. A preliminary investigation on ECH (Wang et al., Proc. Combust. Inst., 35, 2015, 367-375) revealed that an accurate ECH kinetic model with detailed fuel consumption mechanism and aromatic growth pathways, as well as additional ECH pyrolysis and oxidation data with detailed species concentration covering a wide pressure and temperature range are required to understand the ECH combustion kinetics. In this work, the flow reactor pyrolysis of ECH at various pressures (30, 150 and 760Torr) was studied using synchrotron vacuum ultraviolet (VUV) photoionization mass spectrometry (PIMS) and gas chromatography (GC). The mole fraction profiles of numerous major and minor species were evaluated, and good agreement was observed between the PIMS and GC data sets. Furthermore, a fuel-rich burner-stabilized laminar premixed ECH/O2/Ar flame at 30Torr was studied using synchrotron VUV PIMS. A detailed kinetic model for ECH high temperature pyrolysis and oxidation was developed and validated against the pyrolysis and flame data performed in this work. Further validation of the kinetic model is presented against literature data including species concentrations in jet-stirred reactor oxidation, ignition delay times in a shock tube, and laminar flame speeds at various pressures and equivalence ratios. The model well predicts the consumption of ECH, the growth of aromatics, and the global combustion properties. Reaction flux and sensitivity analysis were utilized to elucidate chemical kinetic features of ECH combustion under various reaction conditions. © 2015 The Combustion Institute.

Visual Memory : The Price of Encoding Details

NARCIS (Netherlands)

Nieuwenstein, Mark; Kromm, Maria

2017-01-01

Studies on visual long-term memory have shown that we have a tremendous capacity for remembering pictures of objects, even at a highly detailed level. What remains unclear, however, is whether encoding objects at such a detailed level comes at any cost. In the current study, we examined how the

Older adults report moderately more detailed autobiographical memories.

Science.gov (United States)

Gardner, Robert S; Mainetti, Matteo; Ascoli, Giorgio A

2015-01-01

Autobiographical memory (AM) is an essential component of the human mind. Although the([A-z]+) amount and types of subjective detail (content) that compose AMs constitute important dimensions of recall, age-related changes in memory content are not well characterized. Previously, we introduced the Cue-Recalled Autobiographical Memory test (CRAM; see http://cramtest.info), an instrument that collects subjective reports of AM content, and applied it to college-aged subjects. CRAM elicits AMs using naturalistic word-cues. Subsequently, subjects date each cued AM to a life period and count the number of remembered details from specified categories (features), e.g., temporal detail, spatial detail, persons, objects, and emotions. The current work applies CRAM to a broad range of individuals (18-78 years old) to quantify the effects of age on AM content. Subject age showed a moderately positive effect on AM content: older compared with younger adults reported ∼16% more details (∼25 vs. ∼21 in typical AMs). This age-related increase in memory content was similarly observed for remote and recent AMs, although content declined with the age of the event among all subjects. In general, the distribution of details across features was largely consistent among younger and older adults. However, certain types of details, i.e., those related to objects and sequences of events, contributed more to the age effect on content. Altogether, this work identifies a moderate age-related feature-specific alteration in the way life events are subjectively recalled, among an otherwise stable retrieval profile.

Older adults report moderately more detailed autobiographical memories

Directory of Open Access Journals (Sweden)

Robert S Gardner

2015-05-01

Full Text Available Autobiographical memory (AM is an essential component of the human mind. Although the amount and types of subjective detail (content that compose AMs constitute important dimensions of recall, age-related changes in memory content are not well characterized. Previously, we introduced the Cue-Recalled Autobiographical Memory test (CRAM; see http://cramtest.info, an instrument that collects subjective reports of AM content, and applied it to college-aged subjects. CRAM elicits AMs using naturalistic word-cues. Subsequently, subjects date each cued AM to a life period and count the number of remembered details from specified categories (features, e.g., temporal detail, spatial detail, persons, objects, and emotions. The current work applies CRAM to a broad range of individuals (18-78 years old to quantify the effects of age on AM content. Subject age showed a moderately positive effect on AM content: older compared with younger adults reported ~16% more details (~25 vs. ~21 in typical AMs. This age-related increase in memory content was similarly observed for remote and recent AMs, although content declined with the age of the event among all subjects. In general, the distribution of details across features was largely consistent among younger and older adults. However, certain types of details, i.e., those related to objects and sequences of events, contributed more to the age effect on content. Altogether, this work identifies a moderate age-related feature-specific alteration in the way life events are subjectively recalled, among an otherwise stable retrieval profile.

Analytical calculation of detailed model parameters of cast resin dry-type transformers

International Nuclear Information System (INIS)

Eslamian, M.; Vahidi, B.; Hosseinian, S.H.

2011-01-01

Highlights: → In this paper high frequency behavior of cast resin dry-type transformers was simulated. → Parameters of detailed model were calculated using analytical method and compared with FEM results. → A lab transformer was constructed in order to compare theoretical and experimental results. -- Abstract: Non-flammable characteristic of cast resin dry-type transformers make them suitable for different kind of usages. This paper presents an analytical method of how to obtain parameters of detailed model of these transformers. The calculated parameters are compared and verified with the corresponding FEM results and if it was necessary, correction factors are introduced for modification of the analytical solutions. Transient voltages under full and chopped test impulses are calculated using the obtained detailed model. In order to validate the model, a setup was constructed for testing on high-voltage winding of cast resin dry-type transformer. The simulation results were compared with the experimental data measured from FRA and impulse tests.

Devil in the details? Developmental dyslexia and visual long-term memory for details.

Science.gov (United States)

Huestegge, Lynn; Rohrßen, Julia; van Ermingen-Marbach, Muna; Pape-Neumann, Julia; Heim, Stefan

2014-01-01

Cognitive theories on causes of developmental dyslexia can be divided into language-specific and general accounts. While the former assume that words are special in that associated processing problems are rooted in language-related cognition (e.g., phonology) deficits, the latter propose that dyslexia is rather rooted in a general impairment of cognitive (e.g., visual and/or auditory) processing streams. In the present study, we examined to what extent dyslexia (typically characterized by poor orthographic representations) may be associated with a general deficit in visual long-term memory (LTM) for details. We compared object- and detail-related visual LTM performance (and phonological skills) between dyslexic primary school children and IQ-, age-, and gender-matched controls. The results revealed that while the overall amount of LTM errors was comparable between groups, dyslexic children exhibited a greater portion of detail-related errors. The results suggest that not only phonological, but also general visual resolution deficits in LTM may play an important role in developmental dyslexia.

Polonium-210 in Euphauslids: A Detailed Study

Energy Technology Data Exchange (ETDEWEB)

Heyraud, M.; Fowler, S. W.; Beasley, T. M.; Cherry, R. D.

1976-07-01

A detailed study of {sup 210}Po, the predominant alpha-emitting nuclide found in most marine organisms, has been undertaken in a particular zooplanktonic species, the euphausiid Meganyctiphanes norvegica. The purpose was to obtain information concerning the origin, the localization and the flux of the nuclide in and through this organism. Measurements of {sup 210}Po were made in euphausiids of different sizes, in dissected organs and tissues, and in excretion products. The results show higher concentrations in the smaller specimens; this fact cannot be explained on the basis of surface adsorption, but is probably related to the ingestion of food. Dissection results show that the distribution of {sup 210}Po in euphausiids is not homogeneous, but that the majority is concentrated in the internal organs, the alimentary tract and the hepatopancreas in particular. The natural radiation dose received by these organs is in consequence much higher than that received by the whole animal. Use of a dynamic model allowed the flux of {sup 210}Po through M. norvegica to be calculated. The calculations confirm that food is the principal sauce of {sup 210}Po for this species, and clearly show that fecal pellets constitute the major elimination route. Extrapolation of the data to zooplankton in general leads to the conclusion that zooplankton metabolic activity plays an important role in transporting {sup 210}Po from the surface layers of the ocean to depth. (author)

Human figure drawing distinguishes Alzheimer's patients: a cognitive screening test study.

Science.gov (United States)

Stanzani Maserati, Michelangelo; D'Onofrio, Renato; Matacena, Corrado; Sambati, Luisa; Oppi, Federico; Poda, Roberto; De Matteis, Maddalena; Naldi, Ilaria; Liguori, Rocco; Capellari, Sabina

2018-05-01

To study human figure drawing in a group of Alzheimer's disease (AD) patients and compare it with a group of patients with mild cognitive impairment (MCI) and controls. We evaluated consecutive outpatients over a one-year period. Patients were classified as affected by AD or by MCI. All patients and controls underwent a simplified version of the human-figure drawing test and MMSE. A qualitative and quantitative analysis of all human figures was obtained. 112 AD, 100 MCI patients and 104 controls were enrolled. AD patients drew human figures poor in details and globally smaller than MCI patients and controls. Human figures drawn by MCI patients are intermediate in body height between those of the AD patients and the healthy subjects. The head-to-body ratio of human figures drawn by AD patients is greater than controls and MCI patients, while the human figure size-relative-to-page space index is significantly smaller. Body height is an independent predictor of cognitive impairment correlating with its severity and with the number of the figure's details. Human figures drawn by AD patients are different from those drawn by healthy subjects and MCI patients. Human figure drawing test is a useful tool for orienting cognitive impairment's diagnosis.

The AECL study for an intense neutron - generator (technical details)

Energy Technology Data Exchange (ETDEWEB)

Bartholomew, G A; Tunnicliffe, P R

1966-07-01

The AECL study for an intense neutron-generator has been in progress for two years. Recently the scientific and technical details and the conceptual designs were compiled in a report supporting proposals addressed to AECL's Board of Directors for further work. The compilation is being issued in this form to permit further discussion of the technical aspects. However readers are asked to appreciate that it was written primarily for an AECL audience, and specifically that those chapters giving tentative information about costs, the rate of investment and similar items have been omitted or modified, many references have been made to interim internal reports in order to complete the local documentation, but these references do not imply that the reports themselves can be made generally available. (author)

The AECL study for an intense neutron - generator (technical details)

International Nuclear Information System (INIS)

Bartholomew, G.A.; Tunnicliffe, P.R.

1966-01-01

The AECL study for an intense neutron-generator has been in progress for two years. Recently the scientific and technical details and the conceptual designs were compiled in a report supporting proposals addressed to AECL's Board of Directors for further work. The compilation is being issued in this form to permit further discussion of the technical aspects. However readers are asked to appreciate that it was written primarily for an AECL audience, and specifically that those chapters giving tentative information about costs, the rate of investment and similar items have been omitted or modified, many references have been made to interim internal reports in order to complete the local documentation, but these references do not imply that the reports themselves can be made generally available. (author)

Technical Note: A numerical test-bed for detailed ice nucleation studies in the AIDA cloud simulation chamber

Directory of Open Access Journals (Sweden)

R. J. Cotton

2007-01-01

Full Text Available The AIDA (Aerosol Interactions and Dynamics in the Atmosphere aerosol and cloud chamber of Forschungszentrum Karlsruhe can be used to test the ice forming ability of aerosols. The AIDA chamber is extensively instrumented including pressure, temperature and humidity sensors, and optical particle counters. Expansion cooling using mechanical pumps leads to ice supersaturation conditions and possible ice formation. In order to describe the evolving chamber conditions during an expansion, a parcel model was modified to account for diabatic heat and moisture interactions with the chamber walls. Model results are shown for a series of expansions where the initial chamber temperature ranged from −20°C to −60°C and which used desert dust as ice forming nuclei. During each expansion, the initial formation of ice particles was clearly observed. For the colder expansions there were two clear ice nucleation episodes. In order to test the ability of the model to represent the changing chamber conditions and to give confidence in the observations of chamber temperature and humidity, and ice particle concentration and mean size, ice particles were simply added as a function of time so as to reproduce the observations of ice crystal concentration. The time interval and chamber conditions over which ice nucleation occurs is therefore accurately known, and enables the model to be used as a test bed for different representations of ice formation.

Salt Block I test: experimental details and comparison with theory. Final report

International Nuclear Information System (INIS)

Duffey, T.A.

1980-02-01

A series of laboratory experiments has been completed at Sandia Laboratories to provide an understanding of the steady state and transient thermal response of a large salt block containing an internal heat source. In this report, details of the experimental program are presented along with results of related efforts, such as thermal conductivity experiments, done in support of the heater experiments (Salt Block I). Finite element temperature field predictions, both transient and steady state, are performed utilizing the COYOTE nonlinear heat conduction program. Comparisons of experimental and theoretical results are generally quite good

The influence of study design and sex-differences on results from developmental neurotoxicity studies of bisphenol A: implications for toxicity testing.

Science.gov (United States)

Beronius, Anna; Johansson, Niklas; Rudén, Christina; Hanberg, Annika

2013-09-06

Developmental neurotoxicity (DNT) of bisphenol A (BPA) has been investigated in a large number of studies. However, there are discrepancies in the results reported between the studies. The aim of this study was to identify and analyze factors that may contribute to these differences and to assess whether there are sex-differences in the sensitivity of certain endpoints or tests used in DNT-studies. Forty-four DNT studies of BPA were identified from the open literature. Details about study design and results from each study, as well as the criteria for DNT testing according to the standardized OECD test guideline (TG) 426, were collected in a database. This enabled systematic and detailed comparisons between studies as well as to the criteria and recommendations stated in TG 426. Multivariate analyses were also used to investigate how different factors of the study design contributed to differences in study results. The analyses showed behavioral effects were often observed for endpoints that are not required according to OECD TG 426, such as anxiety-related, social and sexual behaviors, especially at very low doses and in female offspring. On the other hand relatively few studies observed any effects on motor activity, which is commonly used in screening for neurotoxic effects in regulatory testing. However, varied and to some extent seemingly contradictory results have been reported in these studies, especially for endpoints related to motor activity and anxiety and exploration. Many studies were also poorly reported, limiting these analyses. No strong conclusions could be drawn from the multivariate analyses. A few factors of study design, such as the size of the dose and number of dose levels used and the use of litter or individual pup as statistical unit seemed to have some influence on study results. In conclusion, this analysis suggests that DNT-studies conducted according to the standardized OECD TG 426 may overlook sensitive effects of BPA, and possibly

RF Breakdown Studies Using a 1.3 GHZ Test Cell

International Nuclear Information System (INIS)

Sah, R.; Johnson, R.P.; Neubauer, M.; Conde, M.; Gai, W.; Moretti, A.; Popovic, M.; Yonehara, K.; Byrd, J.; Li, D.; BastaniNejad, M.

2009-01-01

Many present and future particle accelerators are limited by the maximum electric gradient and peak surface fields that can be realized in RF cavities. Despite considerable effort, a comprehensive theory of RF breakdown has not been achieved and mitigation techniques to improve practical maximum accelerating gradients have had only limited success. Recent studies have shown that high gradients can be achieved quickly in 805 MHz RF cavities pressurized with dense hydrogen gas without the need for long conditioning times, because the dense gas can dramatically reduce dark currents and multipacting. In this project we use this high pressure technique to suppress effects of residual vacuum and geometry found in evacuated cavities to isolate and study the role of the metallic surfaces in RF cavity breakdown as a function of magnetic field, frequency, and surface preparation. A 1.3-GHz RF test cell with replaceable electrodes (e.g. Mo, Cu, Be, W, and Nb) and pressure barrier capable of operating both at high pressure and in vacuum has been designed and built, and preliminary testing has been completed. A series of detailed experiments is planned at the Argonne Wakefield Accelerator. At the same time, computer simulations of the RF Breakdown process will be carried out to help develop a consistent physics model of RF Breakdown. In order to study the effect of the radiofrequency on RF Breakdown, a second test cell will be designed, fabricated, and tested at a lower frequency, most likely 402.5 MHz.

Devil in the Details? Developmental Dyslexia and Visual Long-Term Memory for Details

Directory of Open Access Journals (Sweden)

Lynn eHuestegge

2014-07-01

Full Text Available Cognitive theories on causes of developmental dyslexia can be divided into language-specific and general accounts. While the former assume that words are special in that associated processing problems are rooted in language-related cognition (e.g., phonology deficits, the latter propose that dyslexia is rather rooted in a general impairment of cognitive (e.g., visual and/or auditory processing streams. In the present study, we examined to what extent dyslexia (typically characterized by poor orthographic representations may be associated with a general deficit in visual long-term memory for details. We compared object- and detail-related visual long-term memory performance (and phonological skills between dyslexic primary school children and IQ-, age- and gender-matched controls. The results revealed that while the overall amount of long-term memory errors was comparable between groups, dyslexic children exhibited a greater portion of detail-related errors. The results suggest that not only phonological, but also general visual resolution deficits in long-term memory may play an important role in developmental dyslexia.

Experimental Test Plan DOE Tidal and River Reference Turbines

Energy Technology Data Exchange (ETDEWEB)

Neary, Vincent S [ORNL; Hill, Craig [St. Anthony Falls Laboratory, 2 Third Avenue SE, Minneapolis, MN 55414; Chamorro, Leonardo [St. Anthony Falls Laboratory, 2 Third Avenue SE, Minneapolis, MN 55414; Gunawan, Budi [ORNL

2012-09-01

Our aim is to provide details of the experimental test plan for scaled model studies in St. Anthony Falls Laboratory (SAFL) Main Channel at the University of Minnesota, including a review of study objectives, descriptions of the turbine models, the experimental set-up, instrumentation details, instrument measurement uncertainty, anticipated experimental test cases, post-processing methods, and data archiving for model developers.

The AECL study for an intense neutron - generator (technical details)

Energy Technology Data Exchange (ETDEWEB)

Bartholomew, G.A.; Tunnicliffe, P.R

1966-07-01

The AECL study for an intense neutron-generator has been in progress for two years. Recently the scientific and technical details and the conceptual designs were compiled in a report supporting proposals addressed to AECL's Board of Directors for further work. The compilation is being issued in this form to permit further discussion of the technical aspects. However readers are asked to appreciate that it was written primarily for an AECL audience, and specifically that those chapters giving tentative information about costs, the rate of investment and similar items have been omitted or modified, many references have been made to interim internal reports in order to complete the local documentation, but these references do not imply that the reports themselves can be made generally available. (author)

Characteristics of physicians targeted by the pharmaceutical industry to participate in e-detailing.

Science.gov (United States)

Alkhateeb, Fadi M; Khanfar, Nile M; Doucette, William R; Loudon, David

2009-01-01

Electronic detailing (e-detailing) has been introduced in the last few years by the pharmaceutical industry as a new communication channel through which to promote pharmaceutical products to physicians. E-detailing involves using digital technology, such as Internet, video conferencing, and interactive voice response, by which drug companies target their marketing efforts toward specific physicians with pinpoint accuracy. A mail survey of 671 Iowa physicians was used to gather information about the physician characteristics and practice setting characteristics of those who are usually targeted by pharmaceutical companies to participate in e-detailing. A model is developed and tested to explain firms' targeting strategy for targeting physicians for e-detailing.

Building a semantic web-based metadata repository for facilitating detailed clinical modeling in cancer genome studies.

Science.gov (United States)

Sharma, Deepak K; Solbrig, Harold R; Tao, Cui; Weng, Chunhua; Chute, Christopher G; Jiang, Guoqian

2017-06-05

Detailed Clinical Models (DCMs) have been regarded as the basis for retaining computable meaning when data are exchanged between heterogeneous computer systems. To better support clinical cancer data capturing and reporting, there is an emerging need to develop informatics solutions for standards-based clinical models in cancer study domains. The objective of the study is to develop and evaluate a cancer genome study metadata management system that serves as a key infrastructure in supporting clinical information modeling in cancer genome study domains. We leveraged a Semantic Web-based metadata repository enhanced with both ISO11179 metadata standard and Clinical Information Modeling Initiative (CIMI) Reference Model. We used the common data elements (CDEs) defined in The Cancer Genome Atlas (TCGA) data dictionary, and extracted the metadata of the CDEs using the NCI Cancer Data Standards Repository (caDSR) CDE dataset rendered in the Resource Description Framework (RDF). The ITEM/ITEM_GROUP pattern defined in the latest CIMI Reference Model is used to represent reusable model elements (mini-Archetypes). We produced a metadata repository with 38 clinical cancer genome study domains, comprising a rich collection of mini-Archetype pattern instances. We performed a case study of the domain "clinical pharmaceutical" in the TCGA data dictionary and demonstrated enriched data elements in the metadata repository are very useful in support of building detailed clinical models. Our informatics approach leveraging Semantic Web technologies provides an effective way to build a CIMI-compliant metadata repository that would facilitate the detailed clinical modeling to support use cases beyond TCGA in clinical cancer study domains.

Detailed Leak Detection Test Plan and schedule for the Oak Ridge National Laboratory liquid low-level waste active pipelines

International Nuclear Information System (INIS)

1994-08-01

This document provides a detailed leak detection test plan and schedule for the pipelines that comprise the active, singly contained, portion of the liquid low-level waste (LLLW) system at the Oak Ridge National Laboratory (ORNL). This plan was prepared in response to the requirements of the Federal Facility Agreement for the Oak Ridge Reservation (FFA) between the U.S. Department of Energy (DOE), the U.S. Environmental Protection Agency (EPA) and the Tennessee Department of Environment and Conservation (TDEC). The LLLW system is an interconnected complex of tanks and pipelines. The FFA distinguishes four categories of tank and pipeline systems within this complex: new or replacement tank systems with secondary containment (Category A), existing tank systems with secondary containment (Category B), existing tank systems without secondary containment (Category C), and tank systems that have been removed from service (Category D). The FFA specifically requires that DOE demonstrate that the Category C systems are not leaking. This plan and schedule addresses testing of the Category C pipelines and the pipelines which are part of Category B tank systems that do not fully meet the requirements for secondary containment as listed in the FFA. A key feature of the plan is that it is based on the use of performance standards for the conduct of release detection testing, and on the use of methods whose performance has been evaluated and shown to meet those standards. Another feature of the plan is that it is based in part on relevant portions of current federal EPA regulations applicable to underground storage tanks and pipelines (UST systems) that store and transfer petroleum products and other hazardous substances. While the FFA does not require that the testing at ORNL follow these regulations, the regulations do provide industry- and regulator-accepted performance standards, as well as a schedule for repeated testing of UST components

Detailed petrographic-structural study of an outcrop of Crystalline Basement of Montevideo

International Nuclear Information System (INIS)

Pascale, A.; Oyhantçabal, P.

2010-01-01

Preliminary data analysis of detailed outcrop Punta Virgilo, located on the S E coast of the department of Montevideo are presented. The investigated outcrop includes gneisses, amphibolite s and several generations of pegmatite and aplite dikes of Paleoproterozoic metamorphic basement, plus a set of dikes emplaced lamprófido exhumed once the area. Petrographic and microstructural studies of metamorphic units allowed to determine the conditions of metamorphism and deformation temperature between 520-720 ° C and pressure between 2 and 6 kbar (depth of 10 to 23 km)

Embodiment in tests of cognitive functioning: A study of an interpreter-mediated dementia evaluation.

Science.gov (United States)

Majlesi, Ali Reza; Plejert, Charlotta

2018-02-01

This study explores how manners of mediation, and the use of embodiment in interpreter-mediated conversation have an impact on tests of cognitive functioning in a dementia evaluation. By a detailed analysis of video recordings, we show how participants-an occupational therapist, an interpreter, and a patient-use embodied practices to make the tasks of a test of cognitive functioning intelligible, and how participants collaboratively put the instructions of the tasks into practice. We demonstrate that both instructions and instructed actions-and the whole procedure of accomplishing the tasks-are shaped co-operatively by embodied practices of all three participants involved in the test situation. Consequently, the accomplishment of the tasks should be viewed as the outcome of a collaborative achievement of instructed actions, rather than an individual product. The result of the study calls attention to issues concerning interpretations of, and the reliability of interpreter-mediated tests and their bearings for diagnostic procedures in dementia evaluations.

Fatigue-Prone Details in Steel Bridges

Directory of Open Access Journals (Sweden)

Mohsen Heshmati

2012-11-01

Full Text Available This paper reviews the results of a comprehensive investigation including more than 100 fatigue damage cases, reported for steel and composite bridges. The damage cases are categorized according to types of detail. The mechanisms behind fatigue damage in each category are identified and studied. It was found that more than 90% of all reported damage cases are of deformation-induced type and generated by some kind of unintentional or otherwise overlooked interaction between different load-carrying members or systems in the bridge. Poor detailing, with unstiffened gaps and abrupt changes in stiffness at the connections between different members were also found to contribute to fatigue cracking in many details.

30 CFR 282.23 - Testing Plan.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Testing Plan. 282.23 Section 282.23 Mineral... § 282.23 Testing Plan. All testing activities shall be conducted in accordance with a Testing Plan... detailed Mining Plan than is obtainable under an approved Delineation Plan, to prepare feasibility studies...

Detailed CFD Modelling of Open Refrigerated Display Cabinets

Directory of Open Access Journals (Sweden)

Pedro Dinis Gaspar

2012-01-01

Full Text Available A comprehensive and detailed computational fluid dynamics (CFDs modelling of air flow and heat transfer in an open refrigerated display cabinet (ORDC is performed in this study. The physical-mathematical model considers the flow through the internal ducts, across fans and evaporator, and includes the thermal response of food products. The air humidity effect and thermal radiation heat transfer between surfaces are taken into account. Experimental tests were performed to characterize the phenomena near physical extremities and to validate the numerical predictions of air temperature, relative humidity, and velocity. Numerical and experimental results comparison reveals the predictive capabilities of the computational model for the optimized conception and development of this type of equipments. Numerical predictions are used to propose geometrical and functional parametric studies that improve thermal performance of the ORDC and consequently food safety.

Preference for Well-Balanced Saliency in Details Cropped from Photographs

Science.gov (United States)

Abeln, Jonas; Fresz, Leonie; Amirshahi, Seyed Ali; McManus, I. Chris; Koch, Michael; Kreysa, Helene; Redies, Christoph

2016-01-01

Photographic cropping is the act of selecting part of a photograph to enhance its aesthetic appearance or visual impact. It is common practice with both professional (expert) and amateur (non-expert) photographers. In a psychometric study, McManus et al. (2011b) showed that participants cropped photographs confidently and reliably. Experts tended to select details from a wider range of positions than non-experts, but other croppers did not generally prefer details that were selected by experts. It remained unclear, however, on what grounds participants selected particular details from a photograph while avoiding other details. One of the factors contributing to cropping decision may be visual saliency. Indeed, various saliency-based computer algorithms are available for the automatic cropping of photographs. However, careful experimental studies on the relation between saliency and cropping are lacking to date. In the present study, we re-analyzed the data from the studies by McManus et al. (2011a,b), focusing on statistical image properties. We calculated saliency-based measures for details selected and details avoided during cropping. As expected, we found that selected details contain regions of higher saliency than avoided details on average. Moreover, the saliency center-of-mass was closer to the geometrical center in selected details than in avoided details. Results were confirmed in an eye tracking study with the same dataset of images. Interestingly, the observed regularities in cropping behavior were less pronounced for experts than for non-experts. In summary, our results suggest that, during cropping, participants tend to select salient regions and place them in an image composition that is well-balanced with respect to the distribution of saliency. Our study contributes to the knowledge of perceptual bottom-up features that are germane to aesthetic decisions in photography and their variability in non-experts and experts. PMID:26793086

Combustion Safety Simplified Test Protocol Field Study

Energy Technology Data Exchange (ETDEWEB)

Brand, L. [Gas Technology Inst., Des Plaines, IL (United States); Cautley, D. [Gas Technology Inst., Des Plaines, IL (United States); Bohac, D. [Gas Technology Inst., Des Plaines, IL (United States); Francisco, P. [Gas Technology Inst., Des Plaines, IL (United States); Shen, L. [Gas Technology Inst., Des Plaines, IL (United States); Gloss, S. [Gas Technology Inst., Des Plaines, IL (United States)

2015-11-01

Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project team collected field data on 11 houses in 2015.

Investigation on Strengthening Approaches Adopted for Poorly Detailed RC Corbels

Directory of Open Access Journals (Sweden)

Ram Chandra Neupane

2017-05-01

Full Text Available Poor detailing of the position of bearing pad over reinforced concrete (RC corbel may lead to premature failure, which is undesired and structurally vulnerable. An appropriate retrofitting solution is necessary to ensure the functionality of such RC corbels. Considering the growing popularity of external carbon fiber-reinforced polymer (CFRP in retrofitting, this research examines the effectiveness of an externally wrapped unidirectional CFRP sheet and compares its performance against traditional retrofitting methods. Moreover, it is intended to fulfill the lack of extensive research on external CFRP application for corbel strengthening. A total of eight medium-scale corbel specimens were tested on vertical load. Observed premature failure due to placing the bearing pad near the edge of corbel was verified and the effectiveness of the proposed structural strengthening solutions was studied. Experimental results show that although the loading capacity of the damaged corbel due to the poor detailing of bearing pad position could not be fully recovered, the external CFRP wrapping method demonstrated superior performance over RC jacketing and was able to prevent localized failure. Further study based on non-linear 3D finite element analysis (FEA was carried out to identify the governing parameters of each retrofitting solution. Numerical studies suggested important parameters of various retrofitting alternatives for higher capacity assurance.

Satisfying the needs of Japanese cancer patients: a comparative study of detailed and standard informed consent documents.

Science.gov (United States)

Sato, Keiko; Watanabe, Toru; Katsumata, Noriyuki; Sato, Tosiya; Ohashi, Yasuo

2014-02-01

Simplified informed consent forms have been successful in improving patient satisfaction and decreasing patient anxiety. However, unsolved problems remain about whether these documents improve comprehension and satisfaction of patients with standard literacy skills. s To investigate whether a detailed consent form explaining the key elements of informed consent, in comparison to a standard consent form, would increase the comprehension and satisfaction of adult cancer patients. Patients who were eligible for the National Surgical Adjuvant Study of Breast Cancer (protocol 01(N-SAS/BC-01)) were randomly selected to receive one of the following four versions: detailed document with graphics, detailed document without graphics, standard document with graphics, and standard document without graphics. The forms were written in plain language from the patients' point of view. A total of 85 patients were administered questionnaires via interview to assess levels of comprehension, satisfaction, and anxiety. Patients demonstrated a strong understanding of information regarding treatment and research. Patient comprehension did not differ significantly between the detailed document arms and the standard document arms. Patient satisfaction level increased according to the amount of information presented in the consent form; most patients preferred the detailed document with graphics. Anxiety and accrual rates in the parent study were not affected by informed consent procedures. Findings were limited to adults who had standard literacy skills and may not be generalizable to a population with lower literacy. Informed consent can be a significant experience for a population with standard literacy skills, as long as the document is easily comprehensible. Such information should be provided in a format that corresponds with patient needs, education levels, and preferences.

Sensory memory consolidation observed: Increased specificity of detail over days

Science.gov (United States)

Weinberger, Norman M.; Miasnikov, Alexandre A.; Chen, Jemmy C.

2010-01-01

Memories are usually multidimensional, including contents such as sensory details, motivational state and emotional overtones. Memory contents generally change over time, most often reported as a loss in the specificity of detail. To study the temporal changes in the sensory contents of associative memory without motivational and emotional contents, we induced memory for acoustic frequency by pairing a tone with stimulation of the cholinergic nucleus basalis. Adult male rats were first tested for behavioral responses (disruption of ongoing respiration) to tones (1–15 kHz), yielding pre-training behavioral frequency generalization gradients (BFGG). They next received three days of training consisting of a conditioned stimulus (CS) tone (8.00 kHz, 70 dB, 2 s) either Paired (n = 5) or Unpaired (n = 5) with weak electrical stimulation (~48 μA) of the nucleus basalis (100 Hz, 0.2 s, co-terminating with CS offset). Testing for behavioral memory was performed by obtaining post-training BFGGs at two intervals, 24 and 96 h after training. At 24 h post-training, the Paired group exhibited associative behavioral memory manifested by significantly larger responses to tone than the Unpaired group. However, they exhibited no specificity in memory for the frequency of the tonal CS, as indexed by a flat BFGG. In contrast, after 96 h post-training the Paired group did exhibit specificity of memory as revealed by tuned BFGGs with a peak at the CS-band of frequencies. This increased detail of memory developed due to a loss of response to lower and higher frequency side-bands, without any change in the absolute magnitude of response to CS-band frequencies. These findings indicate that the sensory contents of associative memory can be revealed to become more specific, through temporal consolidation in the absence of non-sensory factors such as motivation and emotion. PMID:19038352

Sensory memory consolidation observed: increased specificity of detail over days.

Science.gov (United States)

Weinberger, Norman M; Miasnikov, Alexandre A; Chen, Jemmy C

2009-03-01

Memories are usually multidimensional, including contents such as sensory details, motivational state and emotional overtones. Memory contents generally change over time, most often reported as a loss in the specificity of detail. To study the temporal changes in the sensory contents of associative memory without motivational and emotional contents, we induced memory for acoustic frequency by pairing a tone with stimulation of the cholinergic nucleus basalis. Adult male rats were first tested for behavioral responses (disruption of ongoing respiration) to tones (1-15 kHz), yielding pre-training behavioral frequency generalization gradients (BFGG). They next received three days of training consisting of a conditioned stimulus (CS) tone (8.00 kHz, 70 dB, 2 s) either Paired (n=5) or Unpaired (n=5) with weak electrical stimulation (approximately 48 microA) of the nucleus basalis (100 Hz, 0.2 s, co-terminating with CS offset). Testing for behavioral memory was performed by obtaining post-training BFGGs at two intervals, 24 and 96 h after training. At 24 h post-training, the Paired group exhibited associative behavioral memory manifested by significantly larger responses to tone than the Unpaired group. However, they exhibited no specificity in memory for the frequency of the tonal CS, as indexed by a flat BFGG. In contrast, after 96 h post-training the Paired group did exhibit specificity of memory as revealed by tuned BFGGs with a peak at the CS-band of frequencies. This increased detail of memory developed due to a loss of response to lower and higher frequency side-bands, without any change in the absolute magnitude of response to CS-band frequencies. These findings indicate that the sensory contents of associative memory can be revealed to become more specific, through temporal consolidation in the absence of non-sensory factors such as motivation and emotion.

A detailed comparative study between chemical and bioactive properties of Ganoderma lucidum from different origins

NARCIS (Netherlands)

Stojkovic, D.S.; Barros, L.; Calhelha, R.C.; Glamoclija, J.; Ciric, A.; Griensven, van L.J.L.D.; Sokovic, M.; Ferreira, I.C.F.R.

2014-01-01

A detailed comparative study on chemical and bioactive properties of wild and cultivated Ganoderma lucidum from Serbia (GS) and China (GCN) was performed. This species was chosen because of its worldwide use as medicinal mushroom. Higher amounts of sugars were found in GS, while higher amounts of

Transient Studies in Large Offshore Wind Farms, Employing Detailed Circuit Breaker Representation

DEFF Research Database (Denmark)

Glasdam, Jakob Bærholm; Bak, Claus Leth; Hjerrild, Jesper

2012-01-01

in order to ensure reliable switching operations. Transient measurement results in an OWF are compared with simulation results in PSCAD EMTDC and DigSILENT Power Factory. A user-defined model of the vacuum circuit breaker (VCB) is included in both tools, capable of simulating multiple prestrikes during...... greatly improves the simulation results, whereas little improvement is found in DigSILENT. Based on the transient study it is found that the simulated SOV can be up to 60% higher at the sending end when using the detailed VCB representation compared to the built-in switch, which emphasises the need...

Analysis of the ANO-2 turbine trip test

International Nuclear Information System (INIS)

McDonald, T.A.; Tessier, J.H.; Senda, Y.; Waterman, M.D.

1983-01-01

The start-up tests performed with the Arkansas Nuclear One-Unit Two (ANO-2) plant provided an opportunity for studying the validity of certain integral systems codes. In particular, the turbine trip from 98.2 percent full power test was investigated with the RELAP5/MOD1 (cycle 18) ode. A detailed plant model was developed and used to understand the test reports. The early depressurization portion of the transient was reproduced; however, the resultant repressurization was not well represented due to uncertainty in the data and plant response. As a result of these computations and detailed analyses of the test data considerable insight was drawn as to the best way to perform and gather data from such integral systems tests for use in code verification studies

On Detailing in Contemporary Architecture

DEFF Research Database (Denmark)

Kristensen, Claus; Kirkegaard, Poul Henning

2010-01-01

Details in architecture have a significant influence on how architecture is experienced. One can touch the materials and analyse the detailing - thus details give valuable information about the architectural scheme as a whole. The absence of perceptual stimulation like details and materiality...... / tactility can blur the meaning of the architecture and turn it into an empty statement. The present paper will outline detailing in contemporary architecture and discuss the issue with respect to architectural quality. Architectural cases considered as sublime piece of architecture will be presented...

Test Specification of A1-1 Test for OECD-ATLAS Project

International Nuclear Information System (INIS)

Kang, Kyoung-Ho; Moon, Sang-Ki; Lee, Seung-Wook; Choi, Ki-Yong; Song, Chul-Hwa

2014-01-01

In the OECD-ATLAS project, design extension conditions (DECs) such as a station blackout (SBO) and a total loss of feed water (TLOFW) will be experimentally investigated to meet the international interests in the multiple high-risk DECs raised after the Fukushima accident. The proposed test matrix for the OECD-ATLAS project is summarized in Table 1.. In this study, detailed specification of the first test named as A1-1 in the OECD-ATLAS project was described. The target scenario of the A1-1 test is a prolonged SBO with delayed supply of turbine-driven auxiliary feedwater to only SG number 2 (SG-2). A SBO is one of the most important DECs in that without any proper operator actions, a total loss of heat sink leads to core uncover, to core damage, and ultimately a core melt-down scenario under high pressure. Due to this safety importance, a SBO is considered to be a base test item of the OECD-ATLAS project. A detailed specification of the first test named as A1-1 in the OECD-ATLAS project was described. The target scenario of the A1-1 test is a prolonged SBO with delayed supply of turbine-driven auxiliary feedwater to only SG-2 in order to consider an accident mitigation measure. The pre-test analysis using MARS code was performed with an aim of setting up the detailed test procedures for A1-1 test and also gaining the physical insights for a prolonged SBO transient. In the A1-1 test, a prolonged SBO transient will be simulated with two temporal phases: Phase (I) for conservative SBO transient without supply of turbine-driven auxiliary feedwater and Phase (II) for asymmetric cooling via single trained supply of turbine-driven auxiliary feedwater

Detailed Knowledge of the Tuskegee Syphilis Study: Who Knows What? A Framework for Health Promotion Strategies

Science.gov (United States)

Green, B. Lee; Li, Lin; Morris, J. Fontain; Gluzman, Rima; Davis, Jenna L.; Wang, Min Qi; Katz, Ralph V.

2011-01-01

This report explores the level of detailed knowledge about the Tuskegee Syphilis Study (TSS) among 848 Blacks and Whites in three U.S. cities across an array of demographic variables. The Tuskegee Legacy Project (TLP) Questionnaire was used, which was designed to explore the willingness of minorities to participate in biomedical studies. A…

Detailed thermal-hydraulic computation into a containment building

Energy Technology Data Exchange (ETDEWEB)

Caruso. A.; Flour, I.; Simonin, O. [EDF/LNH, Chatou (France); Cherbonnel, C [EDF/SEPTEN, Villeurbanne (France)

1995-09-01

This paper deals with numerical predictions of the influence of water sprays upon stratifications into a containment building using a two-dimensional two-phase flow code. Basic equations and closure assumptions are briefly presented. A test case in a situation involving spray evaporation is first detailed to illustrate the validation step. Then results are presented for a compressible recirculating flow into a containment building with condensation phenomena.

Dispersant testing : a study on analytical test procedures

International Nuclear Information System (INIS)

Fingas, M.F.; Fieldhouse, B.; Wang, Z.; Environment Canada, Ottawa, ON

2004-01-01

Crude oil is a complex mixture of hydrocarbons, ranging from small, volatile compounds to very large, non-volatile compounds. Analysis of the dispersed oil is crucial. This paper described Environment Canada's ongoing studies on various traits of dispersants. In particular, it describes small studies related to dispersant effectiveness and methods to improve analytical procedures. The study also re-evaluated the analytical procedure for the Swirling Flask Test, which is now part of the ASTM standard procedure. There are new and improved methods for analyzing oil-in-water using gas chromatography (GC). The methods could be further enhanced by integrating the entire chromatogram rather than just peaks. This would result in a decrease in maximum variation from 5 per cent to about 2 per cent. For oil-dispersant studies, the surfactant-dispersed oil hydrocarbons consist of two parts: GC-resolved hydrocarbons and GC-unresolved hydrocarbons. This study also tested a second feature of the Swirling Flask Test in which the side spout was tested and compared with a new vessel with a septum port instead of a side spout. This decreased the variability as well as the energy and mixing in the vessel. Rather than being a variation of the Swirling Flask Test, it was suggested that a spoutless vessel might be considered as a completely separate test. 7 refs., 2 tabs., 4 figs

Experimental and detailed kinetic modeling study of PAH formation in laminar co-flow methane diffusion flames

DEFF Research Database (Denmark)

Cuoci, Alberto; Frassoldati, Alessio; Faravelli, Tiziano

2013-01-01

In the present paper, synchrotron VUV photoionization mass spectrometry is used to study the detailed chemistry of co-flow methane diffusion flames with different dilution ratios. The experimental results constitute a comprehensive characterization of species important for PAH and soot formation...

Preoperative Detailed Coagulation Tests Are Required in Patients With Noonan Syndrome.

Science.gov (United States)

Morice, Anne; Harroche, Annie; Cairet, Pascale; Khonsari, Roman H

2017-12-29

Patients with Noonan syndrome often require surgery at young ages. They are at high risk of perioperative bleeding from coagulation defects that might not have been detected by routine screening. These risks are rarely described in the oral and maxillofacial surgery (OMS) literature. The aim of this study was to evaluate the perioperative bleeding risks associated with Noonan syndrome and to propose preoperative guidelines. This report describes a retrospective case series of patients with Noonan syndrome who underwent OMS procedures during a continuous observational period (2013 through 2016) in the authors' center. Clinical data, blood screening test results, and perioperative bleeding were analyzed. Five patients (age, 4 to 20 yr) with Noonan syndrome who underwent OMS procedures were included in this study. One patient presented a spontaneous bleeding tendency (epistaxis requiring cauterization). Blood screening showed clotting defects in 3 patients. One patient presented abnormal perioperative bleeding owing to a mild defect in factor XI. Patients with Noonan syndrome must be referred to a hematologist for specific preoperative investigations and for adapted perioperative management. Copyright © 2017 American Association of Oral and Maxillofacial Surgeons. Published by Elsevier Inc. All rights reserved.

Study of the Rancimat test method in measuring the oxidation stability of biodiesel ester and blends

Energy Technology Data Exchange (ETDEWEB)

Berthiaume, D.; Tremblay, A. [Oleotek Inc., Thetford Mines, PQ (Canada)

2006-11-15

This paper provided details of a study conducted to examine the oxidation stability of biodiesel blends. The study tested samples of canola oil, soybean oil, fish oil, yellow grease, and tallow. The EN 14112 (Rancimat) method was used to compare oxidation stability results obtained in previous tests conducted in the United States and Europe. The aim of the study was also to evaluate the influence of peroxide value (PV), acid value (AV) and feedstock source on the the oxidative stability of different samples. The study also evaluated the possibility of developing a validated test method developed from the EN 14112 methods to specifically consider biodiesel blends. Results of the study indicated that the Rancimat method was not suitable for measuring the oxidation stability of biodiesels blended with petrodiesels. No direct correlation between oxidative stability and PV or AV was observed. It was concluded that fatty acid distribution was not a principal factor in causing changes in oxidation stability. 22 refs., 3 tabs., 1 fig.

Strategy for improving the detailed examination rate for colorectal cancer screening. New approach for detailed colorectal cancer examination. Study for optimal pre-treatment for CT colonography

International Nuclear Information System (INIS)

Mitsushima, Toru; Fujiwara, Masanori; Nagata, Koichi

2012-01-01

In order to drastically improve the detailed examination rate for strategic colorectal cancer examination in Japan, it is necessary to introduce CT colonography (CTC) as a detailed examination method for colorectal cancer examination, in addition to colonoscopy (CS) which is the conventional detailed examination method. In our study, a cleansing enema/contrast solution (3% Nif-C) was prepared by adding 60 ml of a water-soluble iodine-based contrast agent (Gastrografin) and water to an oral cleansing enema agent (Niflec) in solid (powder) form to a final amount of 2000 ml. The solution was compared with a Niflec solution. In terms of patient's acceptability, more than half of the examined patients answered ''easier to drink than the Niflec solution'' or ''as easy to drink as the Niflec solution. '' Also, the Nif-C solution was comparable or superior to the Niflec solution in terms of cleansing enema effects. Regarding imaging effects essential for CTC, the CT level was found to be 200 HU or greater for any large intestine region upon CTC using the Nif-C solution. Thus, practically sufficient imaging effects were achieved. In conclusion, CTC with pretreatment involving a cleansing enema with oral administration of 3% Nif-C is superior to CS in terms of patient's acceptability. In addition, at least in view of the overseas reports on CTC, there is no particular problem in terms of diagnostic accuracy. Thus, CTC is expected to resolve various problems related to colorectal cancer examination in Japan. (author)

Determination of Importance Evaluation for Exploratory Studies Facility (ESF) Subsurface Testing Activities

International Nuclear Information System (INIS)

Goodin, S.

2002-01-01

This Determination of Importance Evaluation (DIE) applies to the Subsurface Exploratory Studies Facility (ESF), encompassing the Topopah Spring (TS) Loop from Station 0+00 meters (m) at the North Portal to breakthrough at the South Portal (approximately 78+77 m), and ancillary test and operation support areas including the Enhanced Characterization of the Repository Block (ECRB) Cross Drift. This evaluation applies specifically to site characterization testing activities ongoing and planned in the Subsurface ESF. ESF site characterization activities are being performed to obtain the information necessary to determine whether the Yucca Mountain Site is suitable as a geologic repository for spent nuclear fuel and high-level radioactive waste. A more detailed description of these testing activities is provided in Section 6 of this DIE. Generally, the construction and operation of excavations associated with these testing activities are evaluated in the DIE for the Subsurface ESF (CRWMS M andO 1999a) and the DIE for the ESF ECRB Cross Drift (CRWMS M andO 2000a). The scope of this DIE also entails the proposed Unsaturated Zone (UZ) Transport Test at Busted Butte. Although, not a part of the TS Loop or ECRB Cross Drift, the associated testing activities are Subsurface testing activities. Busted Butte is located to the south south-east of the TS Loop and is outside the Conceptual Controlled Area Boundary (CCAB). These activities provide access to the Calico Hills (CH) geologic structure. In the case of Busted Butte, construction and operation of excavations are evaluated herein (since this activity was not previously evaluated in CRWMS M andO 1999a). The objectives of this DIE are to determine whether Subsurface ESF testing, and associated activities, could potentially impact site characterization testing and/or the waste isolation capabilities of the site. Controls needed to limit any potential impacts are identified in Section 13. The validity and veracity of the

Author Details

African Journals Online (AJOL)

Ross, E. Vol 104, No 1 (2014) - Articles Parents' perceptions of HIV counselling and testing in schools: Ethical, legal and social implications. Abstract PDF · Vol 104, No 5 (2014) - Articles Parents' perceptions of HIV counselling and testing in schools: Study methodology deeply flawed. Abstract PDF. ISSN: 0256-95749.

Accumulating and remembering the details of neutral and emotional natural scenes.

Science.gov (United States)

Melcher, David

2010-01-01

In contrast to our rich sensory experience with complex scenes in everyday life, the capacity of visual working memory is thought to be quite limited. Here our memory has been examined for the details of naturalistic scenes as a function of display duration, emotional valence of the scene, and delay before test. Individual differences in working memory and long-term memory for pictorial scenes were examined in experiment 1. The accumulation of memory for emotional scenes and the retention of these details in long-term memory were investigated in experiment 2. Although there were large individual differences in performance, memory for scene details generally exceeded the traditional working memory limit within a few seconds. Information about positive scenes was learned most quickly, while negative scenes showed the worst memory for details. The overall pattern of results was consistent with the idea that both short-term and long-term representations are mixed together in a medium-term 'online' memory for scenes.

Exploring new models in all detail with SARAH

CERN Document Server

Staub, Florian

2015-01-01

I give an overview about the features the Mathematica package SARAH provides to study new models. In general, SARAH can handle a wide range of models beyond the MSSM coming with additional chiral superfields, extra gauge groups, or distinctive features like Dirac gaugino masses. All of these models can be implemented in a compact form in SARAH and are easy to use: SARAH extracts all analytical properties of the given model like two-loop renormalization group equations, tadpole equations, mass matrices and vertices. Also one- and two-loop corrections to tadpoles and self-energies can be obtained. For numerical calculations SARAH can be interfaced to other tools to get the mass spectrum, to check flavour or dark matter constraints, and to test the vacuum stability, or to perform collider studies. In particular, the interface to SPheno allows a precise prediction of the Higgs mass in a given model comparable to MSSM precision by incorporating the important two-loop corrections. I show in great detail at the exam...

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or Register ... (2013) - Articles Technical Note: Development of a Photobioreactor for Microalgae Culture ... Design, Construction and Evaluation of Motorized Okra Slicer Abstract PDF ...

False Memories Lack Perceptual Detail: Evidence from Implicit Word-Stem Completion and Perceptual Identification Tests

Science.gov (United States)

Hicks, J.L.; Starns, J.J.

2005-01-01

We used implicit measures of memory to ascertain whether false memories for critical nonpresented items in the DRM paradigm (Deese, 1959; Roediger & McDermott, 1995) contain structural and perceptual detail. In Experiment 1, we manipulated presentation modality in a visual word-stem-completion task. Critical item priming was significant and…

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or Register to ... No 1 (2014) - Articles Knowledge and Attitudes towards Basic Cardiopulmonary Resuscitation (CPR) among Community Nurses in Remo Area of Ogun State, Nigeria

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details ... Design and Implementation of an M/M/1 Queuing Model Algorithm and its Applicability in ... Vehicle Identification Technology to Intercept Small Arms and Ammunition on Nigeria Roads

Detailed Safety Review of Anthrax Vaccine Adsorbed

National Research Council Canada - National Science Library

2001-01-01

To date, 18 human studies have assessed the safety of anthrax vaccination. These studies, some stretching back almost 50 years, reported adverse events after vaccination in varying degrees of detail...

Severn Barrage project. Detailed report - V. 5

Energy Technology Data Exchange (ETDEWEB)

1989-01-01

Prior to the present programme of work, the effects which a tidal power barrage would have on the region, during both construction and operation, had not been studied in detail. This volume of the Detailed Report therefore represents a significant extension of work into these aspects of the Severn Barrage Project. In the Regional Study, a number of benefits have been identified, some of which may represent net benefits nationally. The economic assessment of both regional and national benefits and costs is presented. The second part of this volume reports on the work done on the Legal Background for the Project. (author).

Computer-aided dispatch--traffic management center field operational test final detailed test plan : WSDOT deployment

Science.gov (United States)

2003-10-01

The purpose of this document is to expand upon the evaluation components presented in "Computer-aided dispatch--traffic management center field operational test final evaluation plan : WSDOT deployment". This document defines the objective, approach,...

A thermoacoustic-Stirling heat engine: detailed study

Science.gov (United States)

Backhaus; Swift

2000-06-01

A new type of thermoacoustic engine based on traveling waves and ideally reversible heat transfer is described. Measurements and analysis of its performance are presented. This new engine outperforms previous thermoacoustic engines, which are based on standing waves and intrinsically irreversible heat transfer, by more than 50%. At its most efficient operating point, it delivers 710 W of acoustic power to its resonator with a thermal efficiency of 0.30, corresponding to 41% of the Carnot efficiency. At its most powerful operating point, it delivers 890 W to its resonator with a thermal efficiency of 0.22. The efficiency of this engine can be degraded by two types of acoustic streaming. These are suppressed by appropriate tapering of crucial surfaces in the engine and by using additional nonlinearity to induce an opposing time-averaged pressure difference. Data are presented which show the nearly complete elimination of the streaming convective heat loads. Analysis of these and other irreversibilities show which components of the engine require further research to achieve higher efficiency. Additionally, these data show that the dynamics and acoustic power flows are well understood, but the details of the streaming suppression and associated heat convection are only qualitatively understood.

End region detailing of pretensioned concrete bridge girders : [summary].

Science.gov (United States)

2013-03-01

Introduction of the Florida-I Beam (FIB) in 2009 renewed interest in prestressed concrete beam design, especially end region details. In this study, University of Florida researchers examined construction detailing at the FIB end region.

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or ... The prevention of mother-to-child HIV transmission programme and infant feeding practices ... Evaluation of a diagnostic algorithm for smear-negative pulmonary tuberculosis in ...

Author Details

African Journals Online (AJOL)

Tan, C. Y.. Vol 9, No 7S (2017) - Articles Correlation study between intermetallic layer and drop test for polymer core leadlead-free solder ball under reliability test. Abstract PDF. ISSN: 1112-9867. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL ...

Author Details

African Journals Online (AJOL)

Tan, C. H.. Vol 9, No 7S (2017) - Articles Correlation study between intermetallic layer and drop test for polymer core leadlead-free solder ball under reliability test. Abstract PDF. ISSN: 1112-9867. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL ...

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or Register to get ... Optical bus of centralized relay protection and automation system of medium voltage switchgear for data collection and transmission. Abstract PDF. ISSN: 1112- ...

Theory testing using case studies

DEFF Research Database (Denmark)

Dissing Sørensen, Pernille; Løkke Nielsen, Ann-Kristina

2006-01-01

on the strengths of theory-testing case studies. We specify research paths associated with theory testing in case studies and present a coherent argument for the logic of theoretical development and refinement using case studies. We emphasize different uses of rival explanations and their implications for research...... design. Finally, we discuss the epistemological logic, i.e., the value to larger research programmes, of such studies and, following Lakatos, conclude that the value of theory-testing case studies lies beyond naïve falsification and in their contribution to developing research programmes in a progressive......Case studies may have different research goals. One such goal is the testing of small-scale and middle-range theories. Theory testing refers to the critical examination, observation, and evaluation of the 'why' and 'how' of a specified phenomenon in a particular setting. In this paper, we focus...

Inpile (in PWR) testing of cladding materials

International Nuclear Information System (INIS)

Hahn, R.; Jeong, Y. H.; Baek, B. J.; Kim, K. H.; Kim, S. J.; Choi, B. K.; Kim, J. M.

1999-04-01

As an introduction, the reasons to perform inpile tests are depicted. An overview over general inpile test procedure is given, and test details which are necessary for the development of new alloys for high burnup claddings, like sample geometries and measuring techniques for inpile corrosion testing, are described in detail. Tests for the creep and length change behavior of cladding tubes are described briefly. Finally, conclusions are drawn and literature citations for further test details are given. (author). 9 refs., 2 tabs., 17 figs

Detailed pharmacognostical studies on Berberis aristata DC plant

Directory of Open Access Journals (Sweden)

Bhawana Rathi

2013-01-01

Full Text Available Background: Berberis aristata DC (Berberidaceae commonly known in Hindi as "Dāruhaldi" and "Citra," is an important medicinal herb native to Northern Himalaya region. The plant is used traditionally in Indian system of medicine as an antibacterial, antiperiodic, antidiarrheal and anticancer and it is also used in the treatment of ophthalmic infections. Its root, stem and leaves also find their use in treatment of various ailments and hence is used extensively in Ayurveda. Materials and Methods: Samples of the whole plants of B. aristata were collected and identified. Hand and microtome sections were taken, stained and mounted and the cell content and cell wall structure were studied according to the method described by Kay and Johansen. Representative sketches were made with the help of camera Lucida. Methods for determining the quantitative values were the same as described elsewhere. For fluorescence analysis, the powder of the root, stem and leaf were examined under ultraviolet light. Total ash, acid insoluble ash and water-soluble ash values and water- and alcohol-soluble extractives were determined. Results: The detailed investigations carried on the pharmacognosy of the root; stem and leaf of B. aristata have brought out some salient diagnostic features, which allow one to differentiate it from other substitutes and or adulterants. The determination of quantitative values, fluorescence analysis and the use of lycopodium spore analysis has specifically contributed to this differentiation. Conclusion: From the foregoing observation on the pharmacognosy of root, stem and leaf of B. aristata DC, the salient diagnostic characters of three parts have been presented, which can allow one to differentiate it from other substitutes and or adulterants.

Study of radionuclide contamination at the former Semipalatinsk test site

International Nuclear Information System (INIS)

Artemyev, O.A.

2002-01-01

In the paper the contamination technical areas of the former Semipalatinsk test site is discussed in details. It is concluded, that radioactive contamination of the Degelen technical area caused by underground nuclear tests is mainly retained within tunnels and cavities. Investigation showed that many tunnel portal areas here are contaminated by radioactive substances. Areas of significantly high contamination levels are also found at the Balapan technical area mainly around borehole sleeves. A serious source of radioactive contamination is tritium in used boreholes and high content of radionuclides produced due to the fission of nuclear device and activation of rocks at crater rim around the Atom lake

[Critical reading of articles about diagnostic tests (part I): Are the results of the study valid?].

Science.gov (United States)

Arana, E

2015-01-01

In the era of evidence-based medicine, one of the most important skills a radiologist should have is the ability to analyze the diagnostic literature critically. This tutorial aims to present guidelines for determining whether primary diagnostic articles are valid for clinical practice. The following elements should be evaluated: whether the study can be applied to clinical practice, whether the technique was compared to the reference test, whether an appropriate spectrum of patients was included, whether expectation bias and verification bias were limited, the reproducibility of the study, the practical consequences of the study, the confidence intervals for the parameters analyzed, the normal range for continuous variables, and the placement of the test in the context of other diagnostic tests. We use elementary practical examples to illustrate how to select and interpret the literature on diagnostic imaging and specific references to provide more details. Copyright © 2014 SERAM. Published by Elsevier España, S.L.U. All rights reserved.

A clinical utility study of exome sequencing versus conventional genetic testing in pediatric neurology.

Science.gov (United States)

Vissers, Lisenka E L M; van Nimwegen, Kirsten J M; Schieving, Jolanda H; Kamsteeg, Erik-Jan; Kleefstra, Tjitske; Yntema, Helger G; Pfundt, Rolph; van der Wilt, Gert Jan; Krabbenborg, Lotte; Brunner, Han G; van der Burg, Simone; Grutters, Janneke; Veltman, Joris A; Willemsen, Michèl A A P

2017-09-01

Implementation of novel genetic diagnostic tests is generally driven by technological advances because they promise shorter turnaround times and/or higher diagnostic yields. Other aspects, including impact on clinical management or cost-effectiveness, are often not assessed in detail prior to implementation. We studied the clinical utility of whole-exome sequencing (WES) in complex pediatric neurology in terms of diagnostic yield and costs. We analyzed 150 patients (and their parents) presenting with complex neurological disorders of suspected genetic origin. In a parallel study, all patients received both the standard diagnostic workup (e.g., cerebral imaging, muscle biopsies or lumbar punctures, and sequential gene-by-gene-based testing) and WES simultaneously. Our unique study design allowed direct comparison of diagnostic yield of both trajectories and provided insight into the economic implications of implementing WES in this diagnostic trajectory. We showed that WES identified significantly more conclusive diagnoses (29.3%) than the standard care pathway (7.3%) without incurring higher costs. Exploratory analysis of WES as a first-tier diagnostic test indicates that WES may even be cost-saving, depending on the extent of other tests being omitted. Our data support such a use of WES in pediatric neurology for disorders of presumed genetic origin.Genet Med advance online publication 23 March 2017.

Combined preliminary–detailed design of wind turbines

Directory of Open Access Journals (Sweden)

P. Bortolotti

2016-05-01

Full Text Available This paper is concerned with the holistic optimization of wind turbines. A multi-disciplinary optimization procedure is presented that marries the overall sizing of the machine in terms of rotor diameter and tower height (often termed “preliminary design” with the detailed sizing of its aerodynamic and structural components. The proposed combined preliminary–detailed approach sizes the overall machine while taking into full account the subtle and complicated couplings that arise due to the mutual effects of aerodynamic and structural choices. Since controls play a central role in dictating performance and loads, control laws are also updated accordingly during optimization. As part of the approach, rotor and tower are sized simultaneously, even in this case capturing the mutual effects of one component over the other due to the tip clearance constraint. The procedure, here driven by detailed models of the cost of energy, results in a complete aero-structural design of the machine, including its associated control laws. The proposed methods are tested on the redesign of two wind turbines, a 2.2 MW onshore machine and a large 10 MW offshore one. In both cases, the optimization leads to significant changes with respect to the initial baseline configurations, with noticeable reductions in the cost of energy. The novel procedures are also exercised on the design of low-induction rotors for both considered wind turbines, showing that they are typically not competitive with conventional high-efficiency rotors.

Patient-specific estimation of detailed cochlear shape from clinical CT images

DEFF Research Database (Denmark)

Kjer, H Martin; Fagertun, Jens; Wimmer, Wilhelm

2018-01-01

of the detailed patient-specific cochlear shape from CT images. From a collection of temporal bone [Formula: see text]CT images, we build a cochlear statistical deformation model (SDM), which is a description of how a human cochlea deforms to represent the observed anatomical variability. The model is used...... for regularization of a non-rigid image registration procedure between a patient CT scan and a [Formula: see text]CT image, allowing us to estimate the detailed patient-specific cochlear shape. We test the accuracy and precision of the predicted cochlear shape using both [Formula: see text]CT and CT images...

A thermoacoustic-Stirling heat engine: Detailed study

International Nuclear Information System (INIS)

Backhaus, S.; Swift, G. W.

2000-01-01

A new type of thermoacoustic engine based on traveling waves and ideally reversible heat transfer is described. Measurements and analysis of its performance are presented. This new engine outperforms previous thermoacoustic engines, which are based on standing waves and intrinsically irreversible heat transfer, by more than 50%. At its most efficient operating point, it delivers 710 W of acoustic power to its resonator with a thermal efficiency of 0.30, corresponding to 41% of the Carnot efficiency. At its most powerful operating point, it delivers 890 W to its resonator with a thermal efficiency of 0.22. The efficiency of this engine can be degraded by two types of acoustic streaming. These are suppressed by appropriate tapering of crucial surfaces in the engine and by using additional nonlinearity to induce an opposing time-averaged pressure difference. Data are presented which show the nearly complete elimination of the streaming convective heat loads. Analysis of these and other irreversibilities show which components of the engine require further research to achieve higher efficiency. Additionally, these data show that the dynamics and acoustic power flows are well understood, but the details of the streaming suppression and associated heat convection are only qualitatively understood. (c) 2000 Acoustical Society of America

The Details in the Distributions: Why and how to study phenotypic variability

Science.gov (United States)

Geiler-Samerotte, KA; Bauer, CR; Li, S; Ziv, N; Gresham, D; Siegal, ML

2013-01-01

Phenotypic variability is present even when genetic and environmental differences between cells are reduced to the greatest possible extent. For example, genetically identical bacteria display differing levels of resistance to antibiotics, clonal yeast populations demonstrate morphological and growth-rate heterogeneity, and mouse blastomeres from the same embryo have stochastic differences in gene expression. However, the distributions of phenotypes present among isogenic organisms are often overlooked; instead, many studies focus on population aggregates such as the mean. The details of these distributions are relevant to major questions in diverse fields, including the evolution of antimicrobial-drug and chemotherapy resistance. We review emerging experimental and statistical techniques that allow rigorous analysis of phenotypic variability and thereby may lead to advances across the biological sciences. PMID:23566377

Methods of Usability Testing in Libraries Web Sites

Directory of Open Access Journals (Sweden)

Eman Fawzy

2006-03-01

Full Text Available A Study about libraries' web sites evaluation, that is the Usability, the study talking about methods of usability testing and define it, and its important in web sites evaluation, then details the methods of usability: questionnaire, core groups, testing experimental model, cards arrangement, and composed evaluation.

Spatially confined photoinactivation of bacteria: towards novel tools for detailed mechanistic studies

Science.gov (United States)

Thomsen, Hanna; James, Jeemol; Farewell, Anne; Ericson, Marica B.

2018-02-01

Antimicrobial resistance is a serious global threat fueling an accelerated field of research aimed at developing novel antimicrobial therapies. A particular challenge is the treatment of microbial biofilms formed upon bacterial growth and often associated with chronic infections. Biofilms comprise bacteria that have adhered to a surface and formed 3D microcolonies, and demonstrate significantly increased antimicrobial resistance compared to the planktonic counterpart. A challenge in developing novel strategies for fighting these chronic infections is a lack of mechanistic understanding of what primarily contributes to enhanced drug resistance. Tools for noninvasive study of live biofilms are necessary to begin to understand these mechanisms on both a single cell and 3D level. Herein, a method by which multiphoton microscopy is implemented to study a biofilm model of Staphylococcus epidermidis to noninvasively visualize and measure penetration of compounds in 3D biofilm structure and two photon excitation was exploited for spatially confined photoinactivation and microscopy optimized for evaluation of microbiological viability at a microscopic level. Future studies are aimed at future development of the proposed techniques for detailed studies of, e.g., quorum sensing and mechanisms contributing to antimicrobial resistance.

Reliability of the detailed assessment of speed of handwriting on Flemish children.

Science.gov (United States)

Simons, Johan; Probst, Michel

2014-01-01

This study evaluates the reliability of the Detailed Assessment of Speed of Handwriting (DASH) in a Dutch-speaking sample of children. The sample included 650 boys and 513 girls (age range = 9-16 years). Handwriting speed measurements were obtained using the DASH. Interrater agreement, test-retest reliability, and internal consistency were calculated; gender and age effects were analyzed. Interrater agreement shows excellent reliability with intraclass correlation coefficients of at least 0.94. Test-retest correlations ranged from r = 0.65 to r = 0.81. The internal consistency measures, calculated with Cronbach's alpha, were between 0.88 and 0.94. Both gender and age have a significant effect on handwriting speed, with F (7.1144) = 17.43 (P handwriting speed of Dutch-speaking children. There is a tendency of girls to write faster than boys.

Status of the EU test blanket systems safety studies

International Nuclear Information System (INIS)

Panayotov, Dobromir; Poitevin, Yves; Ricapito, Italo; Zmitko, Milan

2015-01-01

Highlights: • TBS safety demonstration files. • Safety functions and related design features – detailed TBS components classifications. • Nuclear analyses, radiation shielding and protection. • TBS radiological waste management strategy and categorization. • Selection and definition of reference accidents scenarios and accidents analyses. - Abstract: The European joint undertaking for ITER and the development of fusion energy (‘Fusion for Energy’ – F4E) provides the European contributions to the ITER international fusion energy research project. Among others it includes also the development, design, technological demonstration and implementation of the European test blanket systems (TBS) in ITER. Currently two EU TBS designs are in the phase of conceptual design – helium-cooled lithium-lead (HCLL) and helium-cooled pebble-bed (HCPB). Safety demonstration is an important part of the work devoted to the achievement of the next key project milestone the conceptual design review. The paper reveals the details of the work on EU TBS safety performed in the last couple of years: update of the TBS safety demonstration files; safety functions and related design features; detailed TBS components classifications; nuclear analyses, radiation shielding and protection; TBS radiological waste management strategy and categorization; selection and definition of reference accidents scenarios, and accidents analyses. Finally the authors share the information on on-going and planned future EU TBS safety activities.

Status of the EU test blanket systems safety studies

Energy Technology Data Exchange (ETDEWEB)

Panayotov, Dobromir, E-mail: dobromir.panayotov@f4e.europa.eu; Poitevin, Yves; Ricapito, Italo; Zmitko, Milan

2015-10-15

Highlights: • TBS safety demonstration files. • Safety functions and related design features – detailed TBS components classifications. • Nuclear analyses, radiation shielding and protection. • TBS radiological waste management strategy and categorization. • Selection and definition of reference accidents scenarios and accidents analyses. - Abstract: The European joint undertaking for ITER and the development of fusion energy (‘Fusion for Energy’ – F4E) provides the European contributions to the ITER international fusion energy research project. Among others it includes also the development, design, technological demonstration and implementation of the European test blanket systems (TBS) in ITER. Currently two EU TBS designs are in the phase of conceptual design – helium-cooled lithium-lead (HCLL) and helium-cooled pebble-bed (HCPB). Safety demonstration is an important part of the work devoted to the achievement of the next key project milestone the conceptual design review. The paper reveals the details of the work on EU TBS safety performed in the last couple of years: update of the TBS safety demonstration files; safety functions and related design features; detailed TBS components classifications; nuclear analyses, radiation shielding and protection; TBS radiological waste management strategy and categorization; selection and definition of reference accidents scenarios, and accidents analyses. Finally the authors share the information on on-going and planned future EU TBS safety activities.

Design study of a 1 MV, 4 A, D- test bed in european community

International Nuclear Information System (INIS)

Pamela, J.; Hemsworth, R.; Jacquot, C.; Holmes, A.J.T.

1991-01-01

The design study of a 1 MV, 4 A, D - , > 30 seconds, test bed is being conducted by the EURATOM-CEA association (Cadarache) with support from the EURATOM-UKAEA association (Culham) and from FOM-Amsterdam. A proposal for the construction of this test bed at Cadarache will be made by the middle of next year. The options chosen for the beamline are derived from the conceptual design originally proposed one year ago by A.Holmes et al. for the ITER neutral beam systems: pure volume negative ion production, electrostatic multi-stage accelerator, vertically subdivided beamline, electrostatic deflection of the ions at the neutralizer exit, HV vacuum insulation with voltage grading screens. This design has been reviewed in detail and in particular three basic topics have been carefully examined: beam acceleration, gas flow and beam transmission. This review resulted in various changes with respect to the original design, the major change being the decision to put the ion source at high voltage. In parallel to this test bed design study, the conceptual study of a 1 MV, 15 A power supply and of its protection system is conducted by european industrial companies under the supervision of Cadarache

Author Details

African Journals Online (AJOL)

Radwan M.D, Mona Ahmed. Vol 12, No 1 (2000) - Articles RELAPSING REMITTING MULTIPLE SCLEROSIS: CT AND MRI IMAGING VS CLINICAL FINDINGIN THE DIAGNOSIS AND DETERMINATION OF DISEASE ACTIVITY. Details. ISSN: 1110-5607. AJOL African Journals Online. HOW TO USE AJOL... for Researchers ...

LMFBR post accident heat removal testing needs and conceptual design of a test facility

International Nuclear Information System (INIS)

Kleefeldt, K.; Kuechle, M.; Royl, P.; Werle, H.; Boenisch, G.; Heinzel, V.; Mueller, R.A.; Schramm, K.; Smidt, D.

1977-03-01

A study has been carried out in which the needs and requirements for a test facility were derived, enabling detailed investigation of key phenomena anticipated during the post accident heat removal (PAHR) phase as a consequence of a postulated LMFBR whole core accident. Part I of the study concentrates on demonstrating the PAHR phenomena and related testing needs. Three types of experiments were identified which require in-pile testing, ranging from 10 to 70 cm test bed diameter and correspondingly, 30 to 5 W/g minimum power density in the test fuel. In part II a conceptual design for a test facility is presented, emphasizing the capability for accomodating large test beds. This is achieved by a below-reactor-vessel testing device, neutronically coupled to a 100 MWt sodium cooled fast reactor. (orig.) [de

Assessment of alpha radioactivity in Indian tobacco leaf-a detailed study with SSNTD

International Nuclear Information System (INIS)

Ghosh, Dipak; Deb, Argha; Sengupta, Rosalima; Patra, K.K.; Halder, S.; Maiti, S.

2009-01-01

People who inhale tobacco smoke are exposed to higher concentrations of radioactivity since tobacco contains polonium ( 210 Po) and lead ( 210 Pb) both of which are radioactive elements of radon decay series. Among these 210 Po emits damaging type of radiation-alpha radiation is 1000 times more carcinogenic than gamma radiation (DiFranza and Winters, 1982). It generates the localized radiation dose and the health of common people gets affected seriously. In view of this a detail measurement of radioactivity of tobacco leaf is essential. This paper presents a detail investigation on the measurement of alpha radioactivity in raw tobacco leaves, in a few commonly used Indian brand cigarettes and in packed chewing tobacco materials with solid state nuclear track detector (SSNTD). The study reveals the presence of pronounced alpha activity in cigarette tobacco and chewing tobacco samples ranging from 60-75 mBq/gm and 60- 75 mBq/gm. The alpha activity value is comparatively lower in raw tobacco leaves (9-50 mBq/gm). The annual committed effective dose of the smokers of these branded cigarettes has estimated to be 50-700 (μSv/y), whereas the effective dose value in raw tobacco leaves and chewing tobacco samples is 54-201 μSv/y and 230-290 μSv/y, respectively which are within the range found in cigarette samples. (author)

Case Study: Testing with Case Studies

Science.gov (United States)

Herreid, Clyde Freeman

2015-01-01

This column provides original articles on innovations in case study teaching, assessment of the method, as well as case studies with teaching notes. This month's issue discusses using case studies to test for knowledge or lessons learned.

Author Details

African Journals Online (AJOL)

Green, J.M.. Vol 10, No 1 (2001) - Articles Information from Radio Telemetry on movements and exploitation of naturalized Rainbow trout, Oncorhynchus mykiss (Walbaum), in Kenya cold water streams. Details. ISSN: 0002-0036. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians ...

Inoculating against eyewitness suggestibility via interpolated verbatim vs. gist testing.

Science.gov (United States)

Pansky, Ainat; Tenenboim, Einat

2011-01-01

In real-life situations, eyewitnesses often have control over the level of generality in which they choose to report event information. In the present study, we adopted an early-intervention approach to investigate to what extent eyewitness memory may be inoculated against suggestibility, following two different levels of interpolated reporting: verbatim and gist. After viewing a target event, participants responded to interpolated questions that required reporting of target details at either the verbatim or the gist level. After 48 hr, both groups of participants were misled about half of the target details and were finally tested for verbatim memory of all the details. The findings were consistent with our predictions: Whereas verbatim testing was successful in completely inoculating against suggestibility, gist testing did not reduce it whatsoever. These findings are particularly interesting in light of the comparable testing effects found for these two modes of interpolated testing.

Determination of Importance Evaluation for Exploratory Studies Facility (ESF) Subsurface Testing Activities

International Nuclear Information System (INIS)

C.J. Byrne

2001-01-01

This Determination of Importance Evaluation (DIE) applies to the Subsurface Exploratory Studies Facility (ESF), encompassing the Topopah Spring (TS) Loop from Station 0+00 meters (m) at the North Portal to breakthrough at the South Portal (approximately 78+77 m), and ancillary test and operation support areas including the Enhanced Characterization of the Repository Block (ECRB) Cross Drift. This evaluation applies specifically to site characterization testing activities ongoing and planned in the Subsurface ESF. ESF site characterization activities are being performed to obtain the information necessary to determine whether the Yucca Mountain Site is suitable as a geologic repository for spent nuclear fuel and high-level radioactive waste. A more detailed description of these testing activities is provided in Section 6 of this DIE. Generally, the construction and operation of excavations associated with these testing activities are evaluated in the DIE for the Subsurface ESF (CRWMS M and O 1999a) and the DIE for the ESF ECRB Cross Drift (CRWMS M and O 2000a). The scope of this DIE also entails the proposed Unsaturated Zone (UZ) Transport Test at Busted Butte. Although, not a part of the TS Loop or ECRB Cross Drift, the associated testing activities are Subsurface testing activities. Busted Butte is located to the south south-east of the TS Loop and is outside the Conceptual Controlled Area Boundary (CCAB). These activities provide access to the Calico Hills (CH) geologic structure. In the case of Busted Butte, construction and operation of excavations are evaluated herein (since this activity was not previously evaluated in CRWMS M and O 1999a). The objectives of this DIE are to determine whether Subsurface ESF testing, and associated activities, could potentially impact site characterization testing and/or the waste isolation capabilities of the site. Controls needed to limit any potential impacts are identified in Section 13. The validity and veracity of the

Determination of Importance Evaluation for Exploratory Studies Facility (ESF) Subsurface Testing Activities

Energy Technology Data Exchange (ETDEWEB)

C.J. Byrne

2001-02-20

This Determination of Importance Evaluation (DIE) applies to the Subsurface Exploratory Studies Facility (ESF), encompassing the Topopah Spring (TS) Loop from Station 0+00 meters (m) at the North Portal to breakthrough at the South Portal (approximately 78+77 m), and ancillary test and operation support areas including the Enhanced Characterization of the Repository Block (ECRB) Cross Drift. This evaluation applies specifically to site characterization testing activities ongoing and planned in the Subsurface ESF. ESF site characterization activities are being performed to obtain the information necessary to determine whether the Yucca Mountain Site is suitable as a geologic repository for spent nuclear fuel and high-level radioactive waste. A more detailed description of these testing activities is provided in Section 6 of this DIE. Generally, the construction and operation of excavations associated with these testing activities are evaluated in the DIE for the Subsurface ESF (CRWMS M&O 1999a) and the DIE for the ESF ECRB Cross Drift (CRWMS M&O 2000a). The scope of this DIE also entails the proposed Unsaturated Zone (UZ) Transport Test at Busted Butte. Although, not a part of the TS Loop or ECRB Cross Drift, the associated testing activities are Subsurface testing activities. Busted Butte is located to the south south-east of the TS Loop and is outside the Conceptual Controlled Area Boundary (CCAB). These activities provide access to the Calico Hills (CH) geologic structure. In the case of Busted Butte, construction and operation of excavations are evaluated herein (since this activity was not previously evaluated in CRWMS M&O 1999a). The objectives of this DIE are to determine whether Subsurface ESF testing, and associated activities, could potentially impact site characterization testing and/or the waste isolation capabilities of the site. Controls needed to limit any potential impacts are identified in Section 13. The validity and veracity of the individual

Theory Testing Using Case Studies

DEFF Research Database (Denmark)

Møller, Ann-Kristina Løkke; Dissing Sørensen, Pernille

2014-01-01

The appropriateness of case studies as a tool for theory testing is still a controversial issue, and discussions about the weaknesses of such research designs have previously taken precedence over those about its strengths. The purpose of the paper is to examine and revive the approach of theory...... testing using case studies, including the associated research goal, analysis, and generalisability. We argue that research designs for theory testing using case studies differ from theorybuilding case study research designs because different research projects serve different purposes and follow different...... research paths....

Author Details

African Journals Online (AJOL)

Aderinokun, GA. Vol 9, No 1 (1999) - Articles Relative Influence Of Sociodemographic Variables On Oral Health And Habits Of Some Nigerian School Children Abstract · Vol 9, No 4 (1999) - Articles Oral health services in Nigeria Details. ISSN: 0189-2657. AJOL African Journals Online. HOW TO USE AJOL.

Author Details

African Journals Online (AJOL)

A Preliminary Investigation of Relative Frequency of Undiagnosed and Previously Diagnosed Hypertension Before First Stroke in a Lagos Hospital Abstract · Vol 9, No 4 (1999) - Articles Localised tetanus in Lagos, Nigeria Details · Vol 9, No 4 (1999) - Articles Stroke with localised infarction of Wernicke's Area misdiagnosed ...

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text ... Abstract · Vol 17 (2010) - Articles Investigating The Travelling Wave Solution For an SIR Endemic Disease Model With No Disease Related Death (When The Spatial Spread Of The Susceptible Is Not Negligible). Abstract.

Author Details

African Journals Online (AJOL)

Rakotonirina, Alice. Vol 2, No 2 (2002) - Articles Effect of the decoction of rhizomes of Cyperus articulatus on bicuculline-, N-methyl-D-aspartate- and strychnine-induced behavioural excitation and convulsions in mice. Details PDF · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians ...

[Influence of autoclave sterilization on dimensional stability and detail reproduction of 5 additional silicone impression materials].

Science.gov (United States)

Xu, Tong-kai; Sun, Zhi-hui; Jiang, Yong

2012-03-01

To evaluate the dimensional stability and detail reproduction of five additional silicone impression materials after autoclave sterilization. Impressions were made on the ISO 4823 standard mold containing several marking lines, in five kinds of additional silicone. All the impressions were sterilized by high temperature and pressure (135 °C, 212.8 kPa) for 25 min. Linear measurements of pre-sterilization and post-sterilization were made with a measuring microscope. Statistical analysis utilized single-factor analysis with pair-wise comparison of mean values when appropriate. Hypothesis testing was conducted at alpha = 0.05. No significant difference was found between the pre-sterilization and post-sterilization conditions for all locations, and all the absolute valuse of linear rate of change less than 8%. All the sterilization by the autoclave did not affect the surfuce detail reproduction of the 5 impression materials. The dimensional stability and detail reproduction of the five additional silicone impression materials in the study was unaffected by autoclave sterilization.

The devil is in the detail: children's recollection of details about their prior experiences.

Science.gov (United States)

Strange, Deryn; Hayne, Harlene

2013-01-01

Adults sometimes report highly specific details of childhood events, including the weather, what they or others were wearing, as well as information about what they or others said or were thinking at the time. When these details are reported in the course of research they shape our theories of memory development; when they are reported in a criminal trial they influence jurors' evaluation of guilt or innocence. The key question is whether these details were encoded at the time the event took place or have been added after the fact. We addressed this question prospectively by examining the memory accounts of children. In Experiment 1 we coded the reports of 5- to 6-year-olds and 9- to 10-year-olds who had experienced a unique event. We found that spontaneous mentions of these specific details were exceedingly rare. In Experiment 2 we questioned additional children about a similar event using specific questions to extract those details. We found that 9- to 10-year-olds were able to accurately answer, while 5- to 6-year-olds had considerable difficulty. Moreover, when the younger children did respond they provided generic, forensically inadequate, information. These data have important implications for the courtroom and for current theories of memory development and childhood amnesia.

Author Details

African Journals Online (AJOL)

NENTY, N. JOHNSON. Vol 7, No 3 (2001) - Articles Common errors and perfomance of students in junior secondary mathematics certificate examinations in Cross River State, Nigeria Details PDF. ISSN: 1118-0579. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's ...

Author Details

African Journals Online (AJOL)

Admasu, Assefa. Vol 22, No 2 (1999) - Articles Preliminary evaluation of Phytomyza orobanchia (Diptera: Agromyzidae) as a controller of Orobanche spp in Ethiopia Details PDF. ISSN: 2520–7997. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL ...

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Obtaining the green's function for electromagnetic waves propagating in layered in-homogeneous thin film media of spherical particles on a substrate. Abstract · Vol 20, No 2 (2008) - Articles solution growth and ...

Author Details

African Journals Online (AJOL)

Lema, VM. Vol 80, No 9 (2003): - Articles Fournier's gangrene complicating vasectomy. Details PDF · Vol 86, No 6 (2009) - Articles Therapeutic misconception and clinical trials in sub-saharan Africa: A review. Abstract PDF · Vol 86, No 11 (2009) - Articles HIV/AIDS and pregnancy-related deaths in Blantyre, Malawi

Author Details

African Journals Online (AJOL)

Ibeabuchi, NM. Vol 10, No 3 (2000) - Articles Comparison of the effects of Methylsalicylate Cream with cryotherapy on delayed onset muscle soreness. Details · Vol 22, No 2 (2012) - Articles X-ray Pelvimetry And Labour Outcome In Term Pregnancy In A Rural Nigerian Population Abstract. ISSN: 0189-2657. AJOL African ...

Dynamic testing of adhesive joints using a shock testing machine

NARCIS (Netherlands)

Aanhold, J.E. van; Weersink, A.F.J.; Ludolphy, J.W.L.

1998-01-01

A light-weight shock testing machine, designed for type approval testing of naval equipment up to 300 kg mass, has been modified into a dynamic tensile test rig. This enables to test structural details for high rate dynamic tensile loadings such as occur during underwater shock. The maximum capacity

Author Details

African Journals Online (AJOL)

Brown, Duncan. Vol 16, No 2 (2002): Continental Africans & the Question of Identity - Articles Environment and Identity: Douglas Livingstone's A Littoral Zone Details. ISSN: 0256-004. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's ...

Author Details

African Journals Online (AJOL)

SONUGA, F A. Vol 6, No 1 (2000) - Articles Geophysical investigation of Karkarku earthdam embankment. Details. ISSN: 1118-0579. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL ...

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Vol 8 (2004) - Articles Further on stokes expansions for the finite amplitude water waves. Abstract · Vol 11 (2007) - Articles On the effects of wave steepness on higher order Stokes waves. Abstract. ISSN: 1116-4336.

Author Details

African Journals Online (AJOL)

Focho, DA. Vol 2, No 1 (2002) - Articles Observations on the Meiotic Process in the African Pest Grasshopper Taphronota thaelephora Stal. (Orthoptera : Pyrgomorphidae) Details PDF · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's ...

Monte Carlo methods beyond detailed balance

NARCIS (Netherlands)

Schram, Raoul D.; Barkema, Gerard T.|info:eu-repo/dai/nl/101275080

2015-01-01

Monte Carlo algorithms are nearly always based on the concept of detailed balance and ergodicity. In this paper we focus on algorithms that do not satisfy detailed balance. We introduce a general method for designing non-detailed balance algorithms, starting from a conventional algorithm satisfying

Chi-square test and its application in hypothesis testing

Directory of Open Access Journals (Sweden)

Rakesh Rana

2015-01-01

Full Text Available In medical research, there are studies which often collect data on categorical variables that can be summarized as a series of counts. These counts are commonly arranged in a tabular format known as a contingency table. The chi-square test statistic can be used to evaluate whether there is an association between the rows and columns in a contingency table. More specifically, this statistic can be used to determine whether there is any difference between the study groups in the proportions of the risk factor of interest. Chi-square test and the logic of hypothesis testing were developed by Karl Pearson. This article describes in detail what is a chi-square test, on which type of data it is used, the assumptions associated with its application, how to manually calculate it and how to make use of an online calculator for calculating the Chi-square statistics and its associated P-value.

Strategic avionics technology definition studies. Subtask 3-1A3: Electrical Actuation (ELA) Systems Test Facility

Science.gov (United States)

Rogers, J. P.; Cureton, K. L.; Olsen, J. R.

1994-01-01

Future aerospace vehicles will require use of the Electrical Actuator systems for flight control elements. This report presents a proposed ELA Test Facility for dynamic evaluation of high power linear Electrical Actuators with primary emphasis on Thrust Vector Control actuators. Details of the mechanical design, power and control systems, and data acquisition capability of the test facility are presented. A test procedure for evaluating the performance of the ELA Test Facility is also included.

Author Details

African Journals Online (AJOL)

McCarthy, Greg. Vol 15, No 1 (2001): Media Freedom and Human Rights - Articles Caught between Empires: Ambivalence in Australian Films Details. ISSN: 0256-004. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and ...

Author Details

African Journals Online (AJOL)

Ligthelm, A.A.. Vol 5, No 2 (2001) - Articles Community attitudes towards Casinos and the estimated magnitude of problem gambling The Mpumalanga case. Details PDF. ISSN: 1027-4332. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's ...

Author Details

African Journals Online (AJOL)

Comarof, Jean. Vol 1999, No 3-4 (1999) - Articles Alien-Nation: Zombies, Immigrants and Millennial Capitalism Details. ISSN: 0850-8712. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact ...

Author Details

African Journals Online (AJOL)

Njubi, Francis. Vol 15, No 1 (2001): Media Freedom and Human Rights - Articles New Media, Old Struggles: Pan Africanism, Anti-racism and Information Technology Details. ISSN: 0256-004. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's ...

Author Details

African Journals Online (AJOL)

Journal Home > Advanced Search > Author Details. Log in or Register to get access to full text downloads. ... Okeke, EO. Vol 10 (2006) - Articles Analysis of Stokes waves theory as a diffusion problem. Abstract · Vol 11 (2007) - Articles On the impact of wave-current on Stokes waves. Abstract. ISSN: 1116-4336. AJOL African ...

Author Details

African Journals Online (AJOL)

Love, Alison. Vol 29, No 2 (2002) - Articles Policy-makers, the Press and Politics: Reporting a Public Policy Document Details. ISSN: 0379-0622. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use ...

Author Details

African Journals Online (AJOL)

Idowu, OO. Vol 8, No 1 (2003) - Articles Evaluation of Different Substrates and Combinations on the Growth of Pleurotus pulmonarius (Fries) Quelet (Sajor-caju) Details. ISSN: 1118-2733. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's ...

Author Details

African Journals Online (AJOL)

Odigie, IP. Vol 10, No 4 (2000) - Articles High dose vitamin E administration attenuates hypertensin in 2-Kidney 1 Clip Goldblatt hypertensive rats. Details. ISSN: 0189-2657. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms ...

Author Details

African Journals Online (AJOL)

Warnorff, DK. Vol 13, No 4 (2001) - Articles Development of a scoring system for the diagnosis of tuberculous lymphadenitis. Details PDF. ISSN: 1995-7262. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions ...

Terry Turbopump Expanded Operating Band Full-Scale Component and Basic Science Detailed Test Plan - Final.

Energy Technology Data Exchange (ETDEWEB)

Osborn, Douglas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Solom, Matthew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-02-01

This document details the milestone approach to define the true operating limitations (margins) of the Terry turbopump systems used in the nuclear industry for Milestone 3 (full-scale component experiments) and Milestone 4 (Terry turbopump basic science experiments) efforts. The overall multinational-sponsored program creates the technical basis to: (1) reduce and defer additional utility costs, (2) simplify plant operations, and (3) provide a better understanding of the true margin which could reduce overall risk of operations.

PERCON: A flexible computer code for detailed thermal performance studies

International Nuclear Information System (INIS)

Boardman, F.B.; Collier, W.D.

1975-07-01

PERCON is a computer code which evaluates temperatures in three dimensions for a block containing heat sources and having coolant flow in one dimension. The solution is obtained at successive planes perpendicular to the coolant flow and the progression from one plane to the next occurs by the heat to the coolant determining convective boundary conditions at the next plane after due allowance being made for any lateral mixing or mass transfer between coolants. It is also possible to calculate the diametral change along a radius as a function of irradiation shrinkage and thermal expansion. This is used in a 'through life' calculation which evalates interaction pressure in tubular fuel elements. Physical property data used by the code may be specified as functions of temperature. The coolant flow may be specified, or alternatively derived by the program to satisfy either a specified overall pressure drop or mixed mean temperature rise. The pressure drop through each coolant is calculated and the flow modified, followed by a repeat of the temperature calculation, until the pressure imbalance between chosen flow channels at chosen axial positions is less than the specified convergence limit. A detailed description of the facilities in the code is given and some cases which have been studied are discussed. (U.K.)

Minute Impurities Contribute Significantly to Olfactory Receptor Ligand Studies: Tales from Testing the Vibration Theory.

Science.gov (United States)

Paoli, M; Münch, D; Haase, A; Skoulakis, E; Turin, L; Galizia, C G

2017-01-01

Several studies have attempted to test the vibrational hypothesis of odorant receptor activation in behavioral and physiological studies using deuterated compounds as odorants. The results have been mixed. Here, we attempted to test how deuterated compounds activate odorant receptors using calcium imaging of the fruit fly antennal lobe. We found specific activation of one area of the antennal lobe corresponding to inputs from a specific receptor. However, upon more detailed analysis, we discovered that an impurity of 0.0006% ethyl acetate in a chemical sample of benzaldehyde-d 5 was entirely responsible for a sizable odorant-evoked response in Drosophila melanogaster olfactory receptor cells expressing dOr42b. Without gas chromatographic purification within the experimental setup, this impurity would have created a difference in the responses of deuterated and nondeuterated benzaldehyde, suggesting that dOr42b be a vibration sensitive receptor, which we show here not to be the case. Our results point to a broad problem in the literature on use of non-GC-pure compounds to test receptor selectivity, and we suggest how the limitations can be overcome in future studies.

Author Details

African Journals Online (AJOL)

Kioni, P N. Vol 9, No 1 (2007) - Articles Detailed structure of pipe flow with water hammer oscillations. Abstract. ISSN: 1561-7645. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact AJOL ...

Author Details

African Journals Online (AJOL)

Legwaila, GM. Vol 12 (2003) - Articles Review of sweet sorghum: a potential cash and forage crop in Botswana Details. ISSN: 1021-0873. AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use · Contact ...

Author Details

African Journals Online (AJOL)

Akum, ZE. Vol 1, No 3 (2001) - Articles Basic home range characteristics for the conservation of the African grey parrot in the Korup national park, Cameroon Details PDF · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms ...

Author Details

African Journals Online (AJOL)

Bobcokono, Irene Yatabene. Vol 1, No 1 (2001) - Articles Utilisation du papier filtre dans la gestion de programme de lute contre le SIDA au Cameroun Details PDF · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and ...

Author Details

African Journals Online (AJOL)

Erasmus, GJ. Vol 1, No 1 (2001) - Articles Genetic parameter estimates for growth traits in purebred Gudali and two-breed synthetic Wakwa beef cattle in a tropical environment. Details PDF · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's ...

Detailed study of nuclear charge and mass densities. Pt. 1

International Nuclear Information System (INIS)

Berdichevsky, D.; Mosel, U.

1982-01-01

Theoretical and experimental densities are analyzed and compared in detail, in particular in the surface region. For this purpose nuclear size parameters are discussed and new sets of surface parameters are proposed. It is shown that the densities are very close to the error function in the external part of the surface and can be characterized there by two new parameters. For very large r the densities show an exponential behaviour which is analyzed in terms of single-particle density distributions. Furthermore, the effects of the asymmetry, spin-orbit and Coulomb forces on the density distributions are discussed. (orig.)

Moderating the Seductive Details Effect in Multimedia Learning with Note-Taking

Science.gov (United States)

Wang, Zhe; Sundararajan, Narayankripa; Adesope, Olusola O.; Ardasheva, Yuliya

2017-01-01

Although the seductive details effect, a phenomenon where interesting but irrelevant pictures impede comprehension, is well documented, studies examining ways of moderating its detrimental impact on learning remain few. The present study examined the effect of note-taking on the seductive details effect. Chinese undergraduate participants (N = 91)…

Harmonic Frequency Lowering: Effects on the Perception of Music Detail and Sound Quality.

Science.gov (United States)

Kirchberger, Martin; Russo, Frank A

2016-02-01

A novel algorithm for frequency lowering in music was developed and experimentally tested in hearing-impaired listeners. Harmonic frequency lowering (HFL) combines frequency transposition and frequency compression to preserve the harmonic content of music stimuli. Listeners were asked to make judgments regarding detail and sound quality in music stimuli. Stimuli were presented under different signal processing conditions: original, low-pass filtered, HFL, and nonlinear frequency compressed. Results showed that participants reported perceiving the most detail in the HFL condition. In addition, there was no difference in sound quality across conditions. © The Author(s) 2016.

A detailed study of the supernova remnant RCW 86 in TeV {gamma}-rays

Energy Technology Data Exchange (ETDEWEB)

Heinz, Sebastian

2012-03-29

A detailed study of the supernova remnant RCW 86 is presented. RCW 86 encountered a shell-like structure in radio, X-rays and optical, whereas in the discovery paper of RCW 86 in the very high energy regime the structure could not be confirmed. In this thesis for the first time the shell was resolved in the very high energy gamma rays. The shell width was determined to be 0.125 {+-}0.014 , the radius to be 0.194 {+-} 0.016 and the center to be -62.433 {+-}0.014 in declination and 220.734 {+-}0.016 in rectascension. The spectral analysis was performed for the whole SNR and for the south-east part, which is more pronounced in X-rays separately. But the results were comparable within errors. Additionally a power-law with an exponential cut off described the spectra best with the parameters: an spectral index of 1.50{+-}0.28, a cut-off energy of (2.69{+-}0.99 TeV) and an integral flux above 1 TeV of (6.51{+-}2.69) . 10{sup -12} cm{sup -2}s{sup -1}. The study of the correlation of the X-ray and VHE {gamma}-ray data of RCW 86 was hampered by the poor angular resolution of the VHE data. Therefore detailed studies of the Richardson-Lucy deconvolution algorithm have been performed. The outcome is, that deconvolution techniques are applicable to strong VHE {gamma}-ray sources and that fine structure well below the angular resolution can be studied. The application to RX J1713-3946, the brightest SNR in the VHE regime, has shown, that the correlation coefficient of the X-ray data and the VHE data of is stable down to 0.01 and has a value of 0.85. On the other side the significance of the data set is not sufficient in the case of RCW 86 to apply the deconvolution technique.

Energy Systems Test Area (ESTA). Power Systems Test Facilities

Science.gov (United States)

Situ, Cindy H.

2010-01-01

This viewgraph presentation provides a detailed description of the Johnson Space Center's Power Systems Facility located in the Energy Systems Test Area (ESTA). Facilities and the resources used to support power and battery systems testing are also shown. The contents include: 1) Power Testing; 2) Power Test Equipment Capabilities Summary; 3) Source/Load; 4) Battery Facilities; 5) Battery Test Equipment Capabilities Summary; 6) Battery Testing; 7) Performance Test Equipment; 8) Battery Test Environments; 9) Battery Abuse Chambers; 10) Battery Abuse Capabilities; and 11) Battery Test Area Resources.

Feasibility study for biomass power plants in Thailand. Volume 2. appendix: Detailed financial analysis results. Export trade information

International Nuclear Information System (INIS)

1997-01-01

This study, conducted by Black and Veatch, was funded by the U.S. Trade and Development Agency. The report presents a technical and commercial analysis for the development of three nearly identical electricity generating facilities (biomass steam power plants) in the towns of Chachgoengsao, Suphan Buri, and Pichit in Thailand. Volume 2 of the study contains the following appendix: Detailed Financial Analysis Results

Study of the Pierre Auger Observatory ground detectors: tests, simulation and calibration; Etude des detecteurs de surface de l'observatoire Pierre Auger: tests, simulation et etalonnage

Energy Technology Data Exchange (ETDEWEB)

Creusot, A

2004-10-01

The Pierre Auger Observatory is intended to the ultra high energy cosmic rays study. This study is realized through the particles showers coming from the interaction between the cosmic rays and the atmosphere. The ground detection of these showers requires a comprehensive understanding of the detectors. Several test tanks have been elaborated for this purpose, especially the Orsay one. The first chapter is dedicated to the presentation of the cosmic rays and of the Pierre Auger Observatory. The second one describes the detectors used for the Observatory surface array. The Orsay test tank is then presented and detailed. We study the results we have got with the Orsay test tank in the fourth chapter and compare these results with those of the Observatory detectors in the fifth chapter. The sixth chapter is dedicated to the validation of the results set through the simulation (GEANT4 software). Finally, the first detected particles showers are presented in the seventh chapter. The data acquisition has begun this year. The construction will be finished by end of 2005. From this moment, The Pierre Auger Observatory will allow us to contribute to solving the cosmic rays puzzle. (author)

Test design requirements: Thermal conductivity probe testing

International Nuclear Information System (INIS)

Heath, R.E.

1985-01-01

This document establishes the test design requirements for development of a thermal conductivity probe test. The thermal conductivity probe determines in situ thermal conductivity using a line source transient heat conduction analysis. This document presents the rationale for thermal conductivity measurement using a thermal conductivity probe. A general test description is included. Support requirements along with design constraints are detailed to allow simple design of the thermal conductivity probe and test. The schedule and delivery requirements of the responsible test designer are also included. 7 refs., 1 fig

Detailed sensory memory, sloppy working memory

Directory of Open Access Journals (Sweden)

Ilja G Sligte

2010-10-01

Full Text Available Visual short-term memory (VSTM enables us to actively maintain information in mind for a brief period of time after stimulus disappearance. According to recent studies, VSTM consists of three stages - iconic memory, fragile VSTM, and visual working memory - with increasingly stricter capacity limits and progressively longer lifetimes. Still, the resolution (or amount of visual detail of each VSTM stage has remained unexplored and we test this in the present study. We presented people with a change detection task that measures the capacity of all three forms of VSTM, and we added an identification display after each change trial that required people to identify the pre-change object. Accurate change detection plus pre-change identification requires subjects to have a high-resolution representation of the pre-change object, whereas change detection or identification only can be based on the hunch that something has changed, without exactly knowing what was presented before. We observed that people maintained 6.1 objects in iconic memory, 4.6 objects in fragile VSTM and 2.1 objects in visual working memory. Moreover, when people detected the change, they could also identify the pre-change object on 88 percent of the iconic memory trials, on 71 percent of the fragile VSTM trials and merely on 53 percent of the visual working memory trials. This suggests that people maintain many high-resolution representations in iconic memory and fragile VSTM, but only one high-resolution object representation in visual working memory.

Detailed sensory memory, sloppy working memory.

Science.gov (United States)

Sligte, Ilja G; Vandenbroucke, Annelinde R E; Scholte, H Steven; Lamme, Victor A F

2010-01-01

Visual short-term memory (VSTM) enables us to actively maintain information in mind for a brief period of time after stimulus disappearance. According to recent studies, VSTM consists of three stages - iconic memory, fragile VSTM, and visual working memory - with increasingly stricter capacity limits and progressively longer lifetimes. Still, the resolution (or amount of visual detail) of each VSTM stage has remained unexplored and we test this in the present study. We presented people with a change detection task that measures the capacity of all three forms of VSTM, and we added an identification display after each change trial that required people to identify the "pre-change" object. Accurate change detection plus pre-change identification requires subjects to have a high-resolution representation of the "pre-change" object, whereas change detection or identification only can be based on the hunch that something has changed, without exactly knowing what was presented before. We observed that people maintained 6.1 objects in iconic memory, 4.6 objects in fragile VSTM, and 2.1 objects in visual working memory. Moreover, when people detected the change, they could also identify the pre-change object on 88% of the iconic memory trials, on 71% of the fragile VSTM trials and merely on 53% of the visual working memory trials. This suggests that people maintain many high-resolution representations in iconic memory and fragile VSTM, but only one high-resolution object representation in visual working memory.

Test Plan Addendum No. 1: Waste Isolation Pilot Plant bin-scale CH TRU waste tests

International Nuclear Information System (INIS)

Molecke, M.A.; Lappin, A.R.

1990-12-01

This document is the first major revision to the Test Plan: WIPP Bin-Scale CH TRU Waste Tests. Factors that make this revision necessary are described and justified in Section 1, and elaborated upon in Section 4. This addendum contains recommended estimates of, and details for: (1) The total separation of waste leaching/solubility tests from bin-scale gas tests, including preliminary details and quantities of leaching tests required for testing of Levels 1, 2, and 3 WIPP CH TRU wastes; (2) An initial description and quantification of bin-scale gas test Phase 0, added to provide a crucial tie to pretest waste characterization representatives and overall test statistical validation; (3) A revision to the number of test bins required for Phases 1 and 2 of the bin gas test program, and specification of the numbers of additional bin tests required for incorporating gas testing of Level 2 wastes into test Phase 3. Contingencies are stated for the total number of test bins required, both positive and negative, including the supporting assumptions, logic, and decision points. (4) Several other general test detail updates occurring since the Test Plan was approved and published in January, 1990. Possible impacts of recommended revisions included in this Addendum on WIPP site operations are called out and described. 56 refs., 12 tabs

Detailed comparison between computed and measured FBR core seismic responses

International Nuclear Information System (INIS)

Forni, M.; Martelli, A.; Melloni, R.; Bonacina, G.

1988-01-01

This paper presents a detailed comparison between seismic calculations and measurements performed for various mock-ups consisting of groups of seven and nineteen simplified elements of the Italian PEC fast reactor core. Experimental tests had been performed on shaking tables in air and water (simulating sodium) with excitations increasing up to above Safe Shutdown Earthquake. The PEC core-restraint ring had been simulated in some tests. All the experimental tests have been analysed by use of both the one-dimensional computer program CORALIE and the two-dimensional program CLASH. Comparisons have been made for all the instrumented elements, in both the time and the frequency domains. The good agreement between calculations and measurements has confirmed adequacy of the fluid-structure interaction model used for PEC core seismic design verification

[Quality Management and Quality Specifications of Laboratory Tests in Clinical Studies--Challenges in Pre-Analytical Processes in Clinical Laboratories].

Science.gov (United States)

Ishibashi, Midori

2015-01-01

The cost, speed, and quality are the three important factors recently indicated by the Ministry of Health, Labour and Welfare (MHLW) for the purpose of accelerating clinical studies. Based on this background, the importance of laboratory tests is increasing, especially in the evaluation of clinical study participants' entry and safety, and drug efficacy. To assure the quality of laboratory tests, providing high-quality laboratory tests is mandatory. For providing adequate quality assurance in laboratory tests, quality control in the three fields of pre-analytical, analytical, and post-analytical processes is extremely important. There are, however, no detailed written requirements concerning specimen collection, handling, preparation, storage, and shipping. Most laboratory tests for clinical studies are performed onsite in a local laboratory; however, a part of laboratory tests is done in offsite central laboratories after specimen shipping. As factors affecting laboratory tests, individual and inter-individual variations are well-known. Besides these factors, standardizing the factors of specimen collection, handling, preparation, storage, and shipping, may improve and maintain the high quality of clinical studies in general. Furthermore, the analytical method, units, and reference interval are also important factors. It is concluded that, to overcome the problems derived from pre-analytical processes, it is necessary to standardize specimen handling in a broad sense.

Deciphering the details of RNA aminoglycoside interactions: from atomistic models to biotechnological applications

Energy Technology Data Exchange (ETDEWEB)

Ilgu, Muslum [Iowa State Univ., Ames, IA (United States)

2012-01-01

A detailed study was done of the neomycin-B RNA aptamer for determining its selectivity and binding ability to both neomycin– and kanamycin-class aminoglycosides. A novel method to increase drug concentrations in cells for more efficiently killing is described. To test the method, a bacterial model system was adopted and several small RNA molecules interacting with aminoglycosides were cloned downstream of T7 RNA polymerase promoter in an expression vector. Then, the growth analysis of E. coli expressing aptamers was observed for 12-hour period. Our analysis indicated that aptamers helped to increase the intracellular concentration of aminoglycosides thereby increasing their efficacy.

Study of Neurodermatitis Circumscripta Patients with Psychological Tests

Directory of Open Access Journals (Sweden)

Bhushan Kumar

1982-01-01

Full Text Available 2.54 percent of patients attending the dermatology clinic were found to have neurodermatitis circumscripta. Twenty adult male patients with the disease who were p educated at least u to high school were p subjected to detailed psychological testing. They were administered 10 cards of TAT Sinha′s anxiety scale,- self-rating depression scale of Zung and Wechsler adult intelligence scale tests. AU the patients were found to have high IO levels. Anxiety of a very high degree was observed in 55.8 percent of the patients. Anxiety levels were high in patients who were eldest in the family. Sixty five per cent of patients showed high degree of depression, which was more apparent in the younger age group. Patients with first and second ordinal position were more depressed. No relationship was found between the disease and the financial and cdcational status, duration and extent of disease and 1.Q., anxiety or depression levels. Need (n affifiation and (n achievement were the two most dominant needs expressed.

Test-Retest Effects in Treatment Studies of Reading Disability: The Devil Is in the Detail

Science.gov (United States)

McArthur, Genevieve

2007-01-01

Reynolds and Nicolson ("Dyslexia," 2007; 13: 78-96) claim to show that the "dyslexia dyspraxia attention-deficit treatment" (DDAT) benefits children with reading difficulties. However, Rack, Snowling, Hulme, and Gibbs ("Dyslexia," 2007; 13: 97-104) argue that because this study did not include an untrained control group then "all that needs to be…

Detailed analysis of the clinical effects of cell therapy for thoracolumbar spinal cord injury: an original study

Directory of Open Access Journals (Sweden)

Sharma A

2013-07-01

Full Text Available Alok Sharma,1 Nandini Gokulchandran,1 Hemangi Sane,2 Prerna Badhe,1 Pooja Kulkarni,2 Mamta Lohia,3 Anjana Nagrajan,3 Nancy Thomas3 1Department of Medical Services and Clinical Research, 2Department of Research and Development, 3Department of Neurorehabilitation, NeuroGen Brain and Spine Institute, Surana Sethia Hospital and Research Centre, Chembur, Mumbai, India Background: Cell therapy is amongst the most promising treatment strategies in spinal cord injury (SCI because it focuses on repair. There are many published animal studies and a few human trials showing remarkable results with various cell types. The level of SCI determines whether paraplegia or quadriplegia is present, and greatly influences recovery. The purpose of this study was to determine the significance of the clinical effects and long-term safety of intrathecal administration of autologous bone marrow-derived mononuclear cells, along with changes in functional independence and quality of life in patients with thoracolumbar SCI. Methods: We undertook a retrospective analysis of a clinical study in which a nonrandomized sample of 110 patients with thoracolumbar SCI underwent autologous bone marrow-derived mononuclear cell transplantation intrathecally and subsequent neurorehabilitation, with a mean follow-up of 2 years ± 1 month. Changes on any parameters were recorded at follow-up. The data were analyzed using the Wilcoxon's signed-rank test and McNemar's test. Functional Independence Measure and American Spinal Injury Association (ASIA scores were recorded, and a detailed neurological assessment was performed. Results: Overall improvement was seen in 91% of patients, including reduction in spasticity, partial sensory recovery, and improvement in trunk control, postural hypotension, bladder management, mobility, activities of daily living, and functional independence. A significant association of these symptomatic improvements with the cell therapy intervention was established

Statistical methods for conducting agreement (comparison of clinical tests) and precision (repeatability or reproducibility) studies in optometry and ophthalmology.

Science.gov (United States)

McAlinden, Colm; Khadka, Jyoti; Pesudovs, Konrad

2011-07-01

The ever-expanding choice of ocular metrology and imaging equipment has driven research into the validity of their measurements. Consequently, studies of the agreement between two instruments or clinical tests have proliferated in the ophthalmic literature. It is important that researchers apply the appropriate statistical tests in agreement studies. Correlation coefficients are hazardous and should be avoided. The 'limits of agreement' method originally proposed by Altman and Bland in 1983 is the statistical procedure of choice. Its step-by-step use and practical considerations in relation to optometry and ophthalmology are detailed in addition to sample size considerations and statistical approaches to precision (repeatability or reproducibility) estimates. Ophthalmic & Physiological Optics © 2011 The College of Optometrists.

Procedures for parametric studies of costs of superconducting toroidal test assemblies

International Nuclear Information System (INIS)

Thompson, P.B.

1976-05-01

A cost scaling procedure, based on a detailed reference conceptual design, has been developed to determine the effects of variations in the characteristic parameters of superconducting toroidal field coils on project costs. The primary purpose was to provide reasonably simple rational formulae for obtaining approximate costs of a complete installation, focusing on the trends and sensitivities of costs to changes in various parameters such as field strength, coil size, number of coils, and current density rather than establishing absolute costs. No results are included here because early studies applying these procedures are no longer pertinent to the present Superconducting Magnet Development Program. However, planning for the Large Coil Project and the preliminary conceptual design of the Technology Test Assembly with Plasma have employed the techniques described and results will be reported in the appropriate project documents

Characterization and kinetic study of Diels-Alder reaction: Detailed study on N-phenylmaleimide and furan based benzoxazine with potential self-healing application

Directory of Open Access Journals (Sweden)

Z. Stirn

2016-07-01

Full Text Available The Diels-Alder reaction between N-phenylmaleimide and benzoxazine bearing furan group was investigated for the purpose of successful appliance of self-healing in benzoxazine polymer networks. The reaction as a function of temperature/time was performed in molten state and in a solution, where also the kinetic study was performed. The Diels-Alder reaction leads to a mixture of two diastereomers: endo presented at lower cyclo-reversion temperature and exo at higher. Therefore, the conversion rates and exo/endo ratio were studied in detail for both systems. For instance, in molten state the Diels-Alder reaction was triggered by the temperature of the melting point at 60 °C with exo/endo ratio preferable to the endo adduct. The study of the kinetics in a solution revealed that the Diels-Alder reaction followed typical bimolecular reversible second-order reaction. The activation energies were close to the previous literature data; 48.4 and 51.9 kJ·mol–1 for Diels-Alder reaction, and 91.0 and 102.3 kJ·mol–1 for retro-Diels-Alder reaction, in acetonitrile and chloroform, respectively. The reaction equilibrium in a solution is much more affected by the retro-Diels-Alder reaction than in a molten state. This study shows detailed investigation of DA reaction and provides beneficial knowledge for further use in self-healing polymer networks.

MEASURING DETAILED CHEMICAL ABUNDANCES FROM CO-ADDED MEDIUM-RESOLUTION SPECTRA. I. TESTS USING MILKY WAY DWARF SPHEROIDAL GALAXIES AND GLOBULAR CLUSTERS

International Nuclear Information System (INIS)

Yang Lei; Peng, Eric W.; Kirby, Evan N.; Guhathakurta, Puragra; Cheng, Lucy

2013-01-01

The ability to measure metallicities and α-element abundances in individual red giant branch (RGB) stars using medium-resolution spectra (R ≈ 6000) is a valuable tool for deciphering the nature of Milky Way dwarf satellites and the history of the Galactic halo. Extending such studies to more distant systems like Andromeda is beyond the ability of the current generation of telescopes, but by co-adding the spectra of similar stars, we can attain the necessary signal-to-noise ratio (S/N) to make detailed abundance measurements. In this paper, we present a method to determine metallicities and α-element abundances using the co-addition of medium-resolution spectra. We test the method of spectral co-addition using high-S/N spectra of more than 1300 RGB stars from Milky Way globular clusters and dwarf spheroidal galaxies obtained with the Keck II telescope/DEIMOS spectrograph. We group similar stars using photometric criteria and compare the weighted ensemble average abundances ([Fe/H], [Mg/Fe], [Si/Fe], [Ca/Fe], and [Ti/Fe]) of individual stars in each group with the measurements made on the corresponding co-added spectrum. We find a high level of agreement between the two methods, which permits us to apply this co-added spectra technique to more distant RGB stars, like stars in the M31 satellite galaxies. This paper outlines our spectral co-addition and abundance measurement methodology and describes the potential biases in making these measurements.

Outcomes Definitions and Statistical Tests in Oncology Studies: A Systematic Review of the Reporting Consistency.

Science.gov (United States)

Rivoirard, Romain; Duplay, Vianney; Oriol, Mathieu; Tinquaut, Fabien; Chauvin, Franck; Magne, Nicolas; Bourmaud, Aurelie

2016-01-01

Quality of reporting for Randomized Clinical Trials (RCTs) in oncology was analyzed in several systematic reviews, but, in this setting, there is paucity of data for the outcomes definitions and consistency of reporting for statistical tests in RCTs and Observational Studies (OBS). The objective of this review was to describe those two reporting aspects, for OBS and RCTs in oncology. From a list of 19 medical journals, three were retained for analysis, after a random selection: British Medical Journal (BMJ), Annals of Oncology (AoO) and British Journal of Cancer (BJC). All original articles published between March 2009 and March 2014 were screened. Only studies whose main outcome was accompanied by a corresponding statistical test were included in the analysis. Studies based on censored data were excluded. Primary outcome was to assess quality of reporting for description of primary outcome measure in RCTs and of variables of interest in OBS. A logistic regression was performed to identify covariates of studies potentially associated with concordance of tests between Methods and Results parts. 826 studies were included in the review, and 698 were OBS. Variables were described in Methods section for all OBS studies and primary endpoint was clearly detailed in Methods section for 109 RCTs (85.2%). 295 OBS (42.2%) and 43 RCTs (33.6%) had perfect agreement for reported statistical test between Methods and Results parts. In multivariable analysis, variable "number of included patients in study" was associated with test consistency: aOR (adjusted Odds Ratio) for third group compared to first group was equal to: aOR Grp3 = 0.52 [0.31-0.89] (P value = 0.009). Variables in OBS and primary endpoint in RCTs are reported and described with a high frequency. However, statistical tests consistency between methods and Results sections of OBS is not always noted. Therefore, we encourage authors and peer reviewers to verify consistency of statistical tests in oncology studies.

Toward high-efficiency and detailed Monte Carlo simulation study of the granular flow spallation target

Science.gov (United States)

Cai, Han-Jie; Zhang, Zhi-Lei; Fu, Fen; Li, Jian-Yang; Zhang, Xun-Chao; Zhang, Ya-Ling; Yan, Xue-Song; Lin, Ping; Xv, Jian-Ya; Yang, Lei

2018-02-01

The dense granular flow spallation target is a new target concept chosen for the Accelerator-Driven Subcritical (ADS) project in China. For the R&D of this kind of target concept, a dedicated Monte Carlo (MC) program named GMT was developed to perform the simulation study of the beam-target interaction. Owing to the complexities of the target geometry, the computational cost of the MC simulation of particle tracks is highly expensive. Thus, improvement of computational efficiency will be essential for the detailed MC simulation studies of the dense granular target. Here we present the special design of the GMT program and its high efficiency performance. In addition, the speedup potential of the GPU-accelerated spallation models is discussed.

Soot formation in a blast furnace - Prediction via a parametric study, using detailed kinetic modeling

Energy Technology Data Exchange (ETDEWEB)

Nordstroem, T.; Kilpinen, P.; Hupa, M. [Aabo Akademi, Turku (Finland). Combustion Chemistry Group

1996-12-31

The objective of this work has been to investigate the soot formation in a blast furnace fired with heavy fuel oil, using detailed kinetic modelling. This work has been concentrated on parameter studies that could explain under which conditions soot is formed and how that formation could be avoided. The parameters investigated were temperature, pressure, stoichiometric ratio, pyrolysis gas composition and reactor model. The calculations were based on a reaction mechanism that consists of 100 species and 446 reactions including polyaromatic hydrocarbons (PAM) up to 7 aromatic rings SULA 2 Research Programme; 4 refs.

Soot formation in a blast furnace - Prediction via a parametric study, using detailed kinetic modeling

Energy Technology Data Exchange (ETDEWEB)

Nordstroem, T; Kilpinen, P; Hupa, M [Aabo Akademi, Turku (Finland). Combustion Chemistry Group

1997-12-31

The objective of this work has been to investigate the soot formation in a blast furnace fired with heavy fuel oil, using detailed kinetic modelling. This work has been concentrated on parameter studies that could explain under which conditions soot is formed and how that formation could be avoided. The parameters investigated were temperature, pressure, stoichiometric ratio, pyrolysis gas composition and reactor model. The calculations were based on a reaction mechanism that consists of 100 species and 446 reactions including polyaromatic hydrocarbons (PAM) up to 7 aromatic rings SULA 2 Research Programme; 4 refs.

Multicentric randomised study of Helicobacter pylori eradication and pepsinogen testing for prevention of gastric cancer mortality: the GISTAR study.

Science.gov (United States)

Leja, Marcis; Park, Jin Young; Murillo, Raul; Liepniece-Karele, Inta; Isajevs, Sergejs; Kikuste, Ilze; Rudzite, Dace; Krike, Petra; Parshutin, Sergei; Polaka, Inese; Kirsners, Arnis; Santare, Daiga; Folkmanis, Valdis; Daugule, Ilva; Plummer, Martyn; Herrero, Rolando

2017-08-11

Population-based eradication of Helicobacter pylori has been suggested to be cost-effective and is recommended by international guidelines. However, the potential adverse effects of widespread antibiotic use that this would entail have not been sufficiently studied. An alternative way to decrease gastric cancer mortality is by non-invasive search for precancerous lesions, in particular gastric atrophy; pepsinogen tests are the best currently available alternative. The primary objective of GISTAR is to determine whether H pylori eradication combined with pepsinogen testing reduces mortality from gastric cancer among 40-64-year-old individuals. The secondary objectives include evaluation of H pylori eradication effectiveness in gastric cancer prevention in patients with precancerous lesions and evaluation of the potential adverse events, including effects on microbiome. Individuals are recruited from general population (50% men) in areas with high gastric cancer risk in Europe and undergo detailed lifestyle and medical history questionnaire before being randomly allocated to intervention or control groups. The intervention group undergoes H pylori testing and is offered eradication therapy if positive; in addition, pepsinogen levels are detected in plasma and those with decreased levels are referred for upper endoscopy. All participants are offered faecal occult blood testing as an incentive for study participation. Effectiveness of eradication and the spectrum of adverse events are evaluated in study subpopulations. A 35% difference in gastric cancer mortality between the groups is expected to be detectable at 90% power after 15 years if 30 000 individuals are recruited. Biological materials are biobanked for the main and ancillary studies. The study procedure and assumptions will be tested during the pilot phase. The study was approved by the respective ethics committees. An independent Data Safety and Monitoring Board has been established. The findings will be

A review of mammalian carcinogenicity study design and potential effects of alternate test procedures on the safety evaluation of food ingredients.

Science.gov (United States)

Hayes, A W; Dayan, A D; Hall, W C; Kodell, R L; Williams, G M; Waddell, W D; Slesinski, R S; Kruger, C L

2011-06-01

Extensive experience in conducting long term cancer bioassays has been gained over the past 50 years of animal testing on drugs, pesticides, industrial chemicals, food additives and consumer products. Testing protocols for the conduct of carcinogenicity studies in rodents have been developed in Guidelines promulgated by regulatory agencies, including the US EPA (Environmental Protection Agency), the US FDA (Food and Drug Administration), the OECD (Organization for Economic Co-operation and Development) for the EU member states and the MAFF (Ministries of Agriculture, Forestries and Fisheries) and MHW (Ministry of Health and Welfare) in Japan. The basis of critical elements of the study design that lead to an accepted identification of the carcinogenic hazard of substances in food and beverages is the focus of this review. The approaches used by entities well-known for carcinogenicity testing and/or guideline development are discussed. Particular focus is placed on comparison of testing programs used by the US National Toxicology Program (NTP) and advocated in OECD guidelines to the testing programs of the European Ramazzini Foundation (ERF), an organization with numerous published carcinogenicity studies. This focus allows for a good comparison of differences in approaches to carcinogenicity testing and allows for a critical consideration of elements important to appropriate carcinogenicity study designs and practices. OECD protocols serve as good standard models for carcinogenicity testing protocol design. Additionally, the detailed design of any protocol should include attention to the rationale for inclusion of particular elements, including the impact of those elements on study interpretations. Appropriate interpretation of study results is dependent on rigorous evaluation of the study design and conduct, including differences from standard practices. Important considerations are differences in the strain of animal used, diet and housing practices, rigorousness

Hydrothermal Synthesized and Alkaline Activated Carbons Prepared from Glucose and Fructose—Detailed Characterization and Testing in Heavy Metals and Methylene Blue Removal

Directory of Open Access Journals (Sweden)

Sanja Krstić

2018-06-01

Full Text Available In the presented paper, activated carbons were prepared from fructose and glucose, and activating agents (KOH, NaOH, LiOH by hydrothermal treatment (HTC treatment. After preparation, samples were characterized in details. Different techniques were used: x-ray powder diffraction analysis, Raman spectral analysis, elemental analysis, and determination of textural and morphological properties. Obtained results showed dependence of investigated properties and the nature of precursors (glucose or fructose as well as the type of hydroxides used as activating agents. After characterization, samples were tested as materials for heavy metals (Pb2+, Cd2+ and Zn2+ and methylene blue removal. Also, adsorption experiments were performed on wastewaters taken from tailings of the lead and zinc mine and kinetic of the methylene blue removal was studied. The factors which distinguished the KOH activated samples were high yield (~14%, content of organic carbon (63–74%, porosity and specific surface area (SBET ~700–1360 m2/g, a low degree of the crystal phase, indications that potassium ions may be included in heavy metals removal, good removal of the heavy metal ions (~47–59 mg/g for Pb2+, ~21–27 mg/g for Cd2+ and ~6–10 mg/g for Zn2+ and fast (~10–30 min and good methylene blue (~60–200 mg/g removal.

Strengthening of competence planning truss through instructional media development details

Science.gov (United States)

Handayani, Sri; Nurcahyono, M. Hadi

2017-03-01

Competency-Based Learning is a model of learning in which the planning, implementation, and assessment refers to the mastery of competencies. Learning in lectures conducted in the framework for comprehensively realizing student competency. Competence means the orientation of the learning activities in the classroom must be given to the students to be more active learning, active search for information themselves and explore alone or with friends in learning activities in pairs or in groups, learn to use a variety of learning resources and printed materials, electronic media, as well as environment. Analysis of learning wooden structure known weakness in the understanding of the truss detail. Hence the need for the development of media that can provide a clear picture of what the structure of the wooden horses and connection details. Development of instructional media consisted of three phases of activity, namely planning, production and assessment. Learning Media planning should be tailored to the needs and conditions necessary to provide reinforcement to the mastery of competencies, through the table material needs. The production process of learning media is done by using hardware (hardware) and software (software) to support the creation of a medium of learning. Assessment of the media poduk yan include feasibility studies, namely by subject matter experts, media experts, while testing was done according to the student's perception of the product. The results of the analysis of the materials for the instructional aspects of the results obtained 100% (very good) and media analysis for the design aspects of the media expressed very good with a percentage of 88.93%. While the analysis of student perceptions expressed very good with a percentage of 84.84%. Media Learning Truss Details feasible and can be used in the implementation of learning wooden structure to provide capacity-building in planning truss

Author Details

African Journals Online (AJOL)

Isolation and testing the cholesteral reduction ability (in-vitro) of lactococcus lactis from fermented smooth pigweed (amaranthus hybridus) leaves. Abstract PDF · Vol 12, No 6 (2012) - Articles Effect of dietary intakes on pregnancy outcomes: a comparative study among HIV-infected and uninfected women at Nyanza ...

Study of the Pierre Auger Observatory ground detectors: tests, simulation and calibration; Etude des detecteurs de surface de l'observatoire Pierre Auger: tests, simulation et etalonnage

Energy Technology Data Exchange (ETDEWEB)

Creusot, A

2004-10-01

The Pierre Auger Observatory is intended to the ultra high energy cosmic rays study. This study is realized through the particles showers coming from the interaction between the cosmic rays and the atmosphere. The ground detection of these showers requires a comprehensive understanding of the detectors. Several test tanks have been elaborated for this purpose, especially the Orsay one. The first chapter is dedicated to the presentation of the cosmic rays and of the Pierre Auger Observatory. The second one describes the detectors used for the Observatory surface array. The Orsay test tank is then presented and detailed. We study the results we have got with the Orsay test tank in the fourth chapter and compare these results with those of the Observatory detectors in the fifth chapter. The sixth chapter is dedicated to the validation of the results set through the simulation (GEANT4 software). Finally, the first detected particles showers are presented in the seventh chapter. The data acquisition has begun this year. The construction will be finished by end of 2005. From this moment, The Pierre Auger Observatory will allow us to contribute to solving the cosmic rays puzzle. (author)

Full-scale borehole sealing test in salt under simulated downhole conditions. Volume 2

International Nuclear Information System (INIS)

Scheetz, B.E.; Licastro, P.H.; Roy, D.M.

1986-05-01

Large-scale testing of the permeability by brine of a salt/grout sample designed to simulate a borehole plug was conducted. The results of these tests showed that a quantity of fluid equivalent to a permeability of 3 microdarcys was collected during the course of the test. This flow rate was used to estimate the smooth bore aperture. Details of this test ware presented in Volume 1 of this report. This report, Volume 2, covers post-test characterization including a detailed study of the salt/grout interface, as well as determination of the physical/mechanical properties of grout samples molded at Terra Tek, Inc. at the time of the large-scale test. Additional studies include heat of hydration, radial stress, and longitudinal volume changes for an equivalent grout mixture

Study of ignition in a high compression ratio SI (spark ignition) methanol engine using LES (large eddy simulation) with detailed chemical kinetics

International Nuclear Information System (INIS)

Zhen, Xudong; Wang, Yang

2013-01-01

Methanol has been recently used as an alternative to conventional fuels for internal combustion engines in order to satisfy some environmental and economical concerns. In this paper, the ignition in a high compression ratio SI (spark ignition) methanol engine was studied by using LES (large eddy simulation) with detailed chemical kinetics. A 21-species, 84-reaction methanol mechanism was adopted to simulate the auto-ignition process of the methanol/air mixture. The MIT (minimum ignition temperature) and MIE (minimum ignition energy) are two important properties for designing safety standards and understanding the ignition process of combustible mixtures. The effects of the flame kernel size, flame kernel temperature and equivalence ratio were also examined on MIT, MIE and IDP (ignition delay period). The methanol mechanism was validated by experimental test. The simulated results showed that the flame kernel size, temperature and energy dramatically affected the values of the MIT, MIE and IDP for a methanol/air mixture, the value of the ignition delay period was not only related to the flame kernel energy, but also to the flame kernel temperature. - Highlights: • We used LES (large eddy simulation) coupled with detailed chemical kinetics to simulate methanol ignition. • The flame kernel size and temperature affected the minimum ignition temperature. • The flame kernel temperature and energy affected the ignition delay period. • The equivalence ratio of methanol–air mixture affected the ignition delay period

Collaborative recall of details of an emotional film.

Science.gov (United States)

Wessel, Ineke; Zandstra, Anna Roos E; Hengeveld, Hester M E; Moulds, Michelle L

2015-01-01

Collaborative inhibition refers to the phenomenon that when several people work together to produce a single memory report, they typically produce fewer items than when the unique items in the individual reports of the same number of participants are combined (i.e., nominal recall). Yet, apart from this negative effect, collaboration may be beneficial in that group members remove errors from a collaborative report. Collaborative inhibition studies on memory for emotional stimuli are scarce. Therefore, the present study examined both collaborative inhibition and collaborative error reduction in the recall of the details of emotional material in a laboratory setting. Female undergraduates (n = 111) viewed a film clip of a fatal accident and subsequently engaged in either collaborative (n = 57) or individual recall (n = 54) in groups of three. The results show that, across several detail categories, collaborating groups recalled fewer details than nominal groups. However, overall, nominal recall produced more errors than collaborative recall. The present results extend earlier findings on both collaborative inhibition and error reduction to the recall of affectively laden material. These findings may have implications for the applied fields of forensic and clinical psychology.

Co-Simulation of Detailed Whole Building with the Power System to Study Smart Grid Applications

Energy Technology Data Exchange (ETDEWEB)

Makhmalbaf, Atefe; Fuller, Jason C.; Srivastava, Viraj; Ciraci, Selim; Daily, Jeffrey A.

2014-12-24

Modernization of the power system in a way that ensures a sustainable energy system is arguably one of the most pressing concerns of our time. Buildings are important components in the power system. First, they are the main consumers of electricity and secondly, they do not have constant energy demand. Conventionally, electricity has been difficult to store and should be consumed as it is generated. Therefore, maintaining the demand and supply is critical in the power system. However, to reduce the complexity of power models, buildings (i.e., end-use loads) are traditionally modeled and represented as aggregated “dumb” nodes in the power system. This means we lack effective detailed whole building energy models that can support requirements and emerging technologies of the smart power grid. To gain greater insight into the relationship between building energy demand and power system performance, it is important to constitute a co-simulation framework to support detailed building energy modeling and simulation within the power system to study capabilities promised by the modern power grid. This paper discusses ongoing work at Pacific Northwest National Laboratory and presents underlying tools and framework needed to enable co-simulation of building, building energy systems and their control in the power system to study applications such as demand response, grid-based HVAC control, and deployment of buildings for ancillary services. The optimal goal is to develop an integrated modeling and simulation platform that is flexible, reusable, and scalable. Results of this work will contribute to future building and power system studies, especially those related to the integrated ‘smart grid’. Results are also expected to advance power resiliency and local (micro) scale grid studies where several building and renewable energy systems transact energy directly. This paper also reviews some applications that can be supported and studied using the framework introduced

A Study on Individualized Tests

Directory of Open Access Journals (Sweden)

Metin YAŞAR

2017-12-01

Full Text Available This study aims to compare KR-20 reliability levels of “Paper and Pencil Test” developed according to Classical Test Theory and “Individualized Test” developed according to Item Response Theory (Two-Parameter Logistic Model, and the correlation levels of skill measurements obtained via these two methods in a group of students. Individualized test developed in accordance with the Two-Parameter Logistic Model was applied by means of a question pool consisting of 61 multiple-choice items which can be answered in 13 steps. On the other hand, a paper and pencil test of 47 multiple-choice items was applied to the sample student group. After the test developed according to these two methods was applied to the same group, KR-20 reliability coefficient was calculated as 0.67 for the individualized test and as 0.75 for the paper and pencil test prepared according to Classical test theory. Calculated KR-20 reliability coefficients obtained from the study were converted into Fisher Z and tested at the significance level of 0.05. No meaningful difference was detected at the 0.05 significant difference level between the two KR-20 reliability coefficients obtained from the two methods. Pearson Product-Moment Correlation Coefficient was calculated as 0.36 between the points of the individualized test and the measurement results of the paper and pencil test. A positive yet low correlation was observed between the measurement results obtained from the tests developed according to both methods. Consequently, it was seen that at the 0.05 significance level there was no statistically significant difference between KR-20 reliability coefficients of the tests developed according to the two methods and that there was a low correlation between the skill measurements of the students in both tests, but there was no significant correlation at the 0.05 significance level between the skill measurements obtained from both tests.

Author Details

African Journals Online (AJOL)

Inyang-Etoh, PC. Vol 7, No 1 (2008) - Articles A study of association between some live function tests and multiple (HBV and HCV) hepatitis infection. Abstract · Vol 8, No 1 (2009) - Articles Prevalence of Chlamydia trachomatis Infection among Women attending infertility Clinics in Calabar, Nigeria. Abstract. ISSN: 1595-8272.

Author Details

African Journals Online (AJOL)

Magwisha, H.B.. Vol 32, No 1 (2017) - Articles Determination of anthelmintic resistance in goats and sheep using faecal egg count reduction test at Luguruni farm, Dar es Salaam, Tanzania Abstract · Vol 32, No 1 (2017) - Articles Molecular diversity of Theileria parva: a case study of Kilosa district, Morogoro, Tanzania

Detailed sectional anatomy of the spine

International Nuclear Information System (INIS)

Rauschning, W.

1985-01-01

Morphologic studies on the human spine constitute a special challenge because of the spine's complex topographic anatomy and the intimate relationship between the supporting skeleton and the contiguous soft tissues (muscles, discs, joint capsules) as well as the neurovascular contents of the spinal canal and intervertebral foramina. The improving resolution and multiplanar image reformatting capabilities of modern CT scanners call for accurate anatomic reference material. Such anatomic images should be available without distortion, in natural colors, and in considerable detail. The images should present the anatomy in the correct axial, sagittal, and coronal planes and should also be sufficiently closely spaced so as to follow the thin cuts of modern CT scanners. This chapter details one of several recent attempts to correlate gross anatomy with the images depicted by high-resolution CT. The methods of specimen preparation, sectioning, and photographing have been documented elsewhere

Template Assembly for Detailed Urban Reconstruction

KAUST Repository

Nan, Liangliang

2015-05-04

We propose a new framework to reconstruct building details by automatically assembling 3D templates on coarse textured building models. In a preprocessing step, we generate an initial coarse model to approximate a point cloud computed using Structure from Motion and Multi View Stereo, and we model a set of 3D templates of facade details. Next, we optimize the initial coarse model to enforce consistency between geometry and appearance (texture images). Then, building details are reconstructed by assembling templates on the textured faces of the coarse model. The 3D templates are automatically chosen and located by our optimization-based template assembly algorithm that balances image matching and structural regularity. In the results, we demonstrate how our framework can enrich the details of coarse models using various data sets.

Transient Studies in Large Offshore Wind Farms Employing Detailed Circuit Breaker Representation

Directory of Open Access Journals (Sweden)

Jesper Hjerrild

2012-07-01

Full Text Available Switching overvoltages (SOV are considered a possible source of component failures experienced in existing offshore wind farms (OWFs. The inclusion of sufficiently accurate and validated models of the main electrical components in the OWF in the simulation tool is therefore an important issue in order to ensure reliable switching operations. Transient measurement results in an OWF are compared with simulation results in PSCAD EMTDC and DigSILENT Power Factory. A user-defined model of the vacuum circuit breaker (VCB is included in both tools, capable of simulating multiple prestrikes during the closing operation. An analysis of the switching transients that might occur in OWFs will be made on the basis of the validated model, and the importance of the inclusion of a sufficiently accurate representation of the VCB in the simulation tool will be described. The inclusion of the VCB model in PSCAD greatly improves the simulation results, whereas little improvement is found in DigSILENT. Based on the transient study it is found that the simulated SOV can be up to 60% higher at the sending end when using the detailed VCB representation compared to the built-in switch, which emphasises the need for accurate representation of the VCB for energisation studies.

Terry Turbopump Expanded Operating Band Full-Scale Component and Basic Science Detailed Test Plan-Revision 2

Energy Technology Data Exchange (ETDEWEB)

Solom, Matthew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Severe Accident Analysis Dept.; Ross, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Severe Accident Analysis Dept.; Cardoni, Jeffrey N. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Severe Accident Analysis Dept.; Osborn, Douglas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Severe Accident Analysis Dept.

2017-08-01

This document details the milestone approach to define the true operating limitations (margins) of the Terry turbopump systems used in the nuclear industry for Milestone 3 (full-scale component experiments) and Milestone 4 (Terry turbopump basic science experiments) efforts. The overall multinational-sponsored program creates the technical basis to: (1) reduce and defer additional utility costs, (2) simplify plant operations, and (3) provide a better understanding of the true margin which could reduce overall risk of operations.

In situ impulse test: an experimental and analytical evaluation of data interpretation procedures

International Nuclear Information System (INIS)

1975-08-01

Special experimental field testing and analytical studies were undertaken at Fort Lawton in Seattle, Washington, to study ''close-in'' wave propagation and evaluate data interpretation procedures for a new in situ impulse test. This test was developed to determine the shear wave velocity and dynamic modulus of soils underlying potential nuclear power plant sites. The test is different from conventional geophysical testing in that the velocity variation with strain is determined for each test. In general, strains between 10 -1 and 10 -3 percent are achieved. The experimental field work consisted of performing special tests in a large test sand fill to obtain detailed ''close-in'' data. Six recording transducers were placed at various points on the energy source, while approximately 37 different transducers were installed within the soil fill, all within 7 feet of the energy source. Velocity measurements were then taken simultaneously under controlled test conditions to study shear wave propagation phenomenology and help evaluate data interpretation procedures. Typical test data are presented along with detailed descriptions of the results

Girls in detail, boys in shape: gender differences when drawing cubes in depth.

Science.gov (United States)

Lange-Küttner, C; Ebersbach, M

2013-08-01

The current study tested gender differences in the developmental transition from drawing cubes in two- versus three dimensions (3D), and investigated the underlying spatial abilities. Six- to nine-year-old children (N = 97) drew two occluding model cubes and solved several other spatial tasks. Girls more often unfolded the various sides of the cubes into a layout, also called diagrammatic cube drawing (object design detail). In girls, the best predictor for drawing the cubes was Mental Rotation Test (MRT) accuracy. In contrast, boys were more likely to preserve the optical appearance of the cube array. Their drawing in 3D was best predicted by MRT reaction time and the Embedded Figures Test (EFT). This confirmed boys' stronger focus on the contours of an object silhouette (object shape). It is discussed whether the two gender-specific approaches to drawing in three dimensions reflect two sides of the appearance-reality distinction in drawing, that is graphic syntax of object design features versus visual perception of projective space. © 2012 The British Psychological Society.

Author Details

African Journals Online (AJOL)

Hajhosseini, L. Vol 10, No 2 (2013) - Articles The effect of quince leaf (Cydonia oblonga miller) decoction on testes in hypercholesterolemic rabbits: A pilot study. Abstract PDF · Vol 10, No 6 (2013) - Articles Effect of Rosmarinic acid on sertoli cells apoptosis and serum antioxidant levels in rats after exposure to ...

Detailed benchmark test of JENDL-4.0 iron data for fusion applications

Energy Technology Data Exchange (ETDEWEB)

Konno, Chikara, E-mail: konno.chikara@jaea.go.jp [Japan Atomic Energy Agency, Tokai-Mura, Ibaraki-ken, 319-1195 (Japan); Wada, Masayuki [Japan Computer System, Mito, 310-0805 (Japan); Kondo, Keitaro; Ohnishi, Seiki; Takakura, Kosuke; Ochiai, Kentaro; Sato, Satoshi [Japan Atomic Energy Agency, Tokai-Mura, Ibaraki-ken, 319-1195 (Japan)

2011-10-15

The major revised version of Japanese Evaluated Nuclear Data Library (JENDL), JENDL-4.0, was released in May, 2010. As one of benchmark tests, we have carried out a benchmark test of JENDL-4.0 iron data, which are very important for radiation shielding in fusion reactors, by analyzing the iron fusion neutronics integral experiments (in situ and Time-of-Flight (TOF) experiments) at JAEA/FNS. It is demonstrated that the problems of the iron data in the previous version of JENDL, JENDL-3.3, are solved in JENDL-4.0; the first inelastic scattering cross section data of {sup 57}Fe and the angular distribution of the elastic scattering of {sup 56}Fe. The iron data in JENDL-4.0 are comparable to or are partly better than those in ENDF/B-VII.0 and JEFF-3.1.

Acceptance Testing Of Web Applications With Test Description Language

Directory of Open Access Journals (Sweden)

Łukasz Olek

2014-01-01

Full Text Available Acceptance tests are usually created by a client after a part of a system is implemented. However, some methodologies propose the elaboration of test cases before implementing a system. This approach increases the probability of system implementation that fulfills requirements, but may be problematic for customers and testers. To allow acceptance testing in such conditions, we propose to define test cases by recording them on an interactive mockup (a low detailed user-interface prototype. The paper focuses on Test Description Language, a notation used to store test cases.

Barron's SAT subject test

CERN Document Server

Jansen, MA, Robert

2016-01-01

Includes one diagnostic test and three complete tests, all questions answered and explained, self-assessment guides, and subject reviews. Also features test strategies, QR codes to short instructional videos, and a detailed appendix with equations, physical constants, and a basic math review.

Study on vibration alleviating properties of glass fiber reinforced polymer concrete through orthogonal tests

International Nuclear Information System (INIS)

Bai Wenfeng; Zhang Jianhua; Yan Peng; Wang Xinli

2009-01-01

Polymer concrete (PC), because of its good vibration alleviating properties, is a proper material for elementary machine parts in high-precision machine tools. Glass fiber was applied in PC to improve its mechanical properties, and the material obtained is called glass fiber reinforced polymer concrete (GFRPC). The best parameter to estimate the vibration alleviating property is damping ratio. Orthogonal tests were carried out to prepare GFRPC specimens with different component proportions. Damping ratio of the GFRPC specimens was measured. The effect of the factors considered in the experiments on damping ratio of GFRPC was studied. Results of the tests show that granite proportion plays the most important role in determining damping ratio of GFRPC, then flexibilizer dosage and glass fiber length, while epoxy resin dosage and glass fiber dosage play a comparatively less important part. Detailed descriptions were made about how the considered factors affect damping ratio of GFRPC in this paper

Crosshole investigations - details of the construction and operation of the hydraulic testing system

International Nuclear Information System (INIS)

Holmes, D.; Sehlstedt, M.

1986-05-01

The Crosshole Programme, part of the international Stripa Project is designed to evaluate the effectiveness of various remote-sensing techniques in characterising a rock mass around a repository. A multidisciplinary approach has been adopted in which various geophysical, mapping and hydrogeological methods are used to determine the location and characteristics of significant features in the rock. The Programme utilises six boreholes drilled in a fan array from the 360 metre level in the Stripa Mine, Sweden. The hydrogeological component of the work uses single and crosshole testing methods, including sinusoidal pressure testing, to locate fractures and characterise groundwater movement within them. Crosshole methods use packers to isolate portions of two boreholes which both intersect a significant feature in the rock mass. Hydraulic signals are generated in one isolated section and received in the other borehole. This report describes the design and operation of the computer-controlled system which automatically performs the hydrogeological tests. (author) 3 refs., 13 figs

Crosshole investigations - Details of the construction and operation of the hydraulic testing system

International Nuclear Information System (INIS)

Holmes, D.; Sehlstedt, M.

1986-05-01

The Crosshole Programme, part of the international Stripa Project is designed to evaluate the effectiveness of various remote-sensing techniques in characterizing a rock mass around a repository. A multidisciplinary approach has been adopted in which various geophysical, mapping and hydrogeological methods are used to determine the location and characteristics of significant features in the rock. The Programme utilises six boreholes drilled in a fan array from the 360 metre level in the Stripa Mine, Sweden. The hydrogeological component of the work uses single and crosshole testing methods, including sinusoidal pressure testing, to locate fractures and characterize groundwater movement within them. Crosshole methods use packers to isolate portions of two boreholes which both intersect a significant feature in the rock mass. Hydraulic signals are generated in one isolated section and received in the other borehole. This report describes the design and operation of the computer-controlled system which automatically performs the hydrogeological tests. (authors)

Studies on Hepa filter test methods

International Nuclear Information System (INIS)

Lee, S.H.; Jon, K.S.; Park, W.J.; Ryoo, R.

1981-01-01

The purpose of this study is to compare testing methods of the HEPA filter adopted in other countries with each other, and to design and construct a test duct system to establish testing methods. The American D.O.P. test method, the British NaCl test method and several other independently developed methods are compared. It is considered that the D.O.P. method is most suitable for in-plant and leak tests

Template Assembly for Detailed Urban Reconstruction

KAUST Repository

Nan, Liangliang; Wonka, Peter; Ghanem, Bernard; Jiang, Caigui

2015-01-01

Structure from Motion and Multi View Stereo, and we model a set of 3D templates of facade details. Next, we optimize the initial coarse model to enforce consistency between geometry and appearance (texture images). Then, building details are reconstructed

Detail in architecture: Between arts & crafts

Science.gov (United States)

Dulencin, Juraj

2016-06-01

Architectural detail represents an important part of architecture. Not only can it be used as an identifier of a specific building but at the same time enhances the experience of the realized project. Within it lie the signs of a great architect and clues to understanding his or her way of thinking. It is therefore the central topic of a seminar offered to architecture students at the Brno University of Technology. During the course of the semester-long class the students acquaint themselves with atypical architectural details of domestic and international architects by learning to read them, understand them and subsequently draw them by creating architectural blueprints. In other words, by general analysis of a detail the students learn theoretical thinking of its architect who, depending on the nature of the design, had to incorporate a variety of techniques and crafts. Students apply this analytical part to their own architectural detail design. The methodology of the seminar consists of experiential learning by project management and is complemented by a series of lectures discussing a diversity of details as well as materials and technologies required to implement it. The architectural detail design is also part of students' bachelors thesis, therefore, the realistic nature of their blueprints can be verified in the production process of its physical counterpart. Based on their own documentation the students choose the most suitable manufacturing process whether it is supplied by a specific technology or a craftsman. Students actively participate in the production and correct their design proposals in real scale with the actual material. A student, as a future architect, stands somewhere between a client and an artisan, materializes his or her idea and adjusts the manufacturing process so that the final detail fulfills aesthetic consistency and is in harmony with its initial concept. One of the very important aspects of the design is its economic cost, an

The E-ELT project: the telescope main structure detailed design study

Science.gov (United States)

Marchiori, Gianpietro; Busatta, Andrea; Ghedin, Leonardo; De Lorenzi, Simone

2012-09-01

The European Extremely Large Telescope (E-ELT) is the biggest telescope in the world. Within the Detailed Design activities, ESO has awarded EIE GROUP (European Industrial Engineering) a contract for the Design of the Main Structure to the point where the concept of the telescope has been consolidated, from a construction point of view. All the Design activities have been developed in order to create an integrated system in terms of functionality and performance, while the engineering activities have been performed with the aim of obtaining a telescope that can be built, transported, integrated, with a reduced maintainability.

One Curve Embedded Full-Bridge MMC Modeling Method with Detailed Representation of IGBT Characteristics

Science.gov (United States)

Hongyang, Yu; Zhengang, Lu; Xi, Yang

2017-05-01

Modular Multilevel Converter is more and more widely used in high voltage DC transmission system and high power motor drive system. It is a major topological structure for high power AC-DC converter. Due to the large module number, the complex control algorithm, and the high power user’s back ground, the MMC model used for simulation should be as accurate as possible to simulate the details of how MMC works for the dynamic testing of the MMC controller. But so far, there is no sample simulation MMC model which can simulate the switching dynamic process. In this paper, one curve embedded full-bridge MMC modeling method with detailed representation of IGBT characteristics is proposed. This method is based on the switching curve referring and sample circuit calculation, and it is sample for implementation. Based on the simulation comparison test under Matlab/Simulink, the proposed method is proved to be correct.

The effects of free recall testing on subsequent source memory.

Science.gov (United States)

Brewer, Gene A; Marsh, Richard L; Meeks, Joseph T; Clark-Foos, Arlo; Hicks, Jason L

2010-05-01

The testing effect is the finding that prior retrieval of information from memory will result in better subsequent memory for that material. One explanation for these effects is that initial free recall testing increases the recollective details for tested information, which then becomes more available during a subsequent test phase. In three experiments we explored this hypothesis using a source-monitoring test phase after the initial free recall tests. We discovered that memory is differentially enhanced for certain recollective details depending on the nature of the free recall task. Thus further research needs to be conducted to specify how different kinds of memorial details are enhanced by free recall testing.

Validations of CFD against detailed velocity and pressure measurements in water turbine runner flow

Science.gov (United States)

Nilsson, H.; Davidson, L.

2003-03-01

This work compares CFD results with experimental results of the flow in two different kinds of water turbine runners. The runners studied are the GAMM Francis runner and the Hölleforsen Kaplan runner. The GAMM Francis runner was used as a test case in the 1989 GAMM Workshop on 3D Computation of Incompressible Internal Flows where the geometry and detailed best efficiency measurements were made available. In addition to the best efficiency measurements, four off-design operating condition measurements are used for the comparisons in this work. The Hölleforsen Kaplan runner was used at the 1999 Turbine 99 and 2001 Turbine 99 - II workshops on draft tube flow, where detailed measurements made after the runner were used as inlet boundary conditions for the draft tube computations. The measurements are used here to validate computations of the flow in the runner.The computations are made in a single runner blade passage where the inlet boundary conditions are obtained from an extrapolation of detailed measurements (GAMM) or from separate guide vane computations (Hölleforsen). The steady flow in a rotating co-ordinate system is computed. The effects of turbulence are modelled by a low-Reynolds number k- turbulence model, which removes some of the assumptions of the commonly used wall function approach and brings the computations one step further.

The development of a Flight Test Engineer's Workstation for the Automated Flight Test Management System

Science.gov (United States)

Tartt, David M.; Hewett, Marle D.; Duke, Eugene L.; Cooper, James A.; Brumbaugh, Randal W.

1989-01-01

The Automated Flight Test Management System (ATMS) is being developed as part of the NASA Aircraft Automation Program. This program focuses on the application of interdisciplinary state-of-the-art technology in artificial intelligence, control theory, and systems methodology to problems of operating and flight testing high-performance aircraft. The development of a Flight Test Engineer's Workstation (FTEWS) is presented, with a detailed description of the system, technical details, and future planned developments. The goal of the FTEWS is to provide flight test engineers and project officers with an automated computer environment for planning, scheduling, and performing flight test programs. The FTEWS system is an outgrowth of the development of ATMS and is an implementation of a component of ATMS on SUN workstations.

Program plan for the DOE Office of Fusion Energy First Wall/Blanket/Shield Engineering Technology Program. Volume II. Detailed technical plan. Revision 2

International Nuclear Information System (INIS)

1982-08-01

The four sections which comprise Part II describe in detail the technical basis for each of the four Program Elements (PE's) of the FWBS Engineering Technology Program (ETP). Each PE is planned to be executed in a number of phases. The purpose of the DTP's is to delineate detailed near-term research, development, and testing required to establish a FWBS engineering data base. Optimum testing strategies and construction of test facilities where needed are identified. The DTP's are based on guidelines given by Argonne National Laboratory which included the basic programmatic goals and the requirements for the types of tests and test conditions

Peer Review of “LDT Weight Reduction Study with Crash Model, Feasibility and Detailed Cost Analyses – Chevrolet Silverado 1500 Pickup”

Science.gov (United States)

The contractor will conduct an independent peer review of FEV’s light-duty truck (LDT) mass safety study, “Light-Duty Vehicle Weight Reduction Study with Crash Model, Feasibility and Detailed Cost Analysis – Silverado 1500”, and its corresponding computer-aided engineering (CAE) ...

Modelling and Testing of Friction in Forging

DEFF Research Database (Denmark)

Bay, Niels

2007-01-01

Knowledge about friction is still limited in forging. The theoretical models applied presently for process analysis are not satisfactory compared to the advanced and detailed studies possible to carry out by plastic FEM analyses and more refined models have to be based on experimental testing...

Academic detailing.

Science.gov (United States)

Shankar, P R; Jha, N; Piryani, R M; Bajracharya, O; Shrestha, R; Thapa, H S

2010-01-01

There are a number of sources available to prescribers to stay up to date about medicines. Prescribers in rural areas in developing countries however, may not able to access some of them. Interventions to improve prescribing can be educational, managerial, and regulatory or use a mix of strategies. Detailing by the pharmaceutical industry is widespread. Academic detailing (AD) has been classically seen as a form of continuing medical education in which a trained health professional such as a physician or pharmacist visits physicians in their offices to provide evidence-based information. Face-to-face sessions, preferably on an individual basis, clear educational and behavioural objectives, establishing credibility with respect to objectivity, stimulating physician interaction, use of concise graphic educational materials, highlighting key messages, and when possible, providing positive reinforcement of improved practices in follow-up visits can increase success of AD initiatives. AD is common in developed countries and certain examples have been cited in this review. In developing countries the authors have come across reports of AD in Pakistan, Sudan, Argentina and Uruguay, Bihar state in India, Zambia, Cuba, Indonesia and Mexico. AD had a consistent, small but potentially significant impact on prescribing practices. AD has much less resources at its command compared to the efforts by the industry. Steps have to be taken to formally start AD in Nepal and there may be specific hindering factors similar to those in other developing nations.

Test of understanding of vectors: A reliable multiple-choice vector concept test

Science.gov (United States)

Barniol, Pablo; Zavala, Genaro

2014-06-01

In this article we discuss the findings of our research on students' understanding of vector concepts in problems without physical context. First, we develop a complete taxonomy of the most frequent errors made by university students when learning vector concepts. This study is based on the results of several test administrations of open-ended problems in which a total of 2067 students participated. Using this taxonomy, we then designed a 20-item multiple-choice test [Test of understanding of vectors (TUV)] and administered it in English to 423 students who were completing the required sequence of introductory physics courses at a large private Mexican university. We evaluated the test's content validity, reliability, and discriminatory power. The results indicate that the TUV is a reliable assessment tool. We also conducted a detailed analysis of the students' understanding of the vector concepts evaluated in the test. The TUV is included in the Supplemental Material as a resource for other researchers studying vector learning, as well as instructors teaching the material.

Test beam studies of possibilities to separate particles with gamma factors above 103 with straw based Transition Radiation Detector

Science.gov (United States)

Belyaev, N.; Cherry, M. L.; Doronin, S. A.; Filippov, K.; Fusco, P.; Konovalov, S.; Krasnopevtsev, D.; Kramarenko, V.; Loparco, F.; Mazziotta, M. N.; Ponomarenko, D.; Pyatiizbyantseva, D.; Radomskii, R.; Rembser, C.; Romaniouk, A.; Savchenko, A.; Shulga, E.; Smirnov, S.; Smirnov, Yu; Sosnovtsev, V.; Spinelli, P.; Teterin, P.; Tikhomirov, V.; Vorobev, K.; Zhukov, K.

2017-12-01

Measurements of hadron production in the TeV energy range are one of the tasks of the future studies at the Large Hadron Collider (LHC). The main goal of these experiments is a study of the fundamental QCD processes at this energy range, which is very important not only for probing of the Standard Model but also for ultrahigh-energy cosmic particle physics. One of the key elements of these experiments measurements are hadron identification. The only detector technology which has a potential ability to separate hadrons in this energy range is Transition Radiation Detector (TRD) technology. TRD prototype based on straw proportional chambers combined with a specially assembled radiator has been tested at the CERN SPS accelerator beam. The test beam results and comparison with detailed Monte Carlo simulations are presented here.

Testing and evaluation of light ablation decontamination

International Nuclear Information System (INIS)

Demmer, R.L.; Ferguson, R.L.

1994-10-01

This report details the testing and evaluation of light ablation decontamination. It details WINCO contracted research and application of light ablation efforts by Ames Laboratory. Tests were conducted with SIMCON (simulated contamination) coupons and REALCON (actual radioactive metal coupons) under controlled conditions to compare cleaning effectiveness, speed and application to plant process type equipment

Fusion Materials Irradiation Test Facility: experimental capabilities and test matrix

International Nuclear Information System (INIS)

Opperman, E.K.

1982-01-01

This report describes the experimental capabilities of the Fusion Materials Irradiation Test Facility (FMIT) and reference material specimen test matrices. The description of the experimental capabilities and the test matrices has been updated to match the current single test cell facility ad assessed experimenter needs. Sufficient detail has been provided so that the user can plan irradiation experiments and conceptual hardware. The types of experiments, irradiation environment and support services that will be available in FMIT are discussed

Tests of Local Hadron Calibration Approaches in ATLAS Combined Beam Tests

International Nuclear Information System (INIS)

Grahn, Karl-Johan; Kiryunin, Andrey; Pospelov, Guennadi

2011-01-01

Three ATLAS calorimeters in the region of the forward crack at |η| 3.2 in the nominal ATLAS setup and a typical section of the two barrel calorimeters at |η| = 0.45 of ATLAS have been exposed to combined beam tests with single electrons and pions. Detailed shower shape studies of electrons and pions with comparisons to various Geant4 based simulations utilizing different physics lists are presented for the endcap beam test. The local hadron calibration approach as used in the full Atlas setup has been applied to the endcap beam test data. An extension of it using layer correlations has been tested with the barrel test beam data. Both methods utilize modular correction steps based on shower shape variables to correct for invisible energy inside the reconstructed clusters in the calorimeters (compensation) and for lost energy deposits outside of the reconstructed clusters (dead material and out-of-cluster deposits). Results for both methods and comparisons to Monte Carlo simulations are presented.

Aquarius Reflector Surface Temperature Monitoring Test and Analysis

Science.gov (United States)

Abbott, Jamie; Lee, Siu-Chun; Becker, Ray

2008-01-01

The presentation addresses how to infer the front side temperatures for the Aquarius L-band reflector based upon backside measurement sites. Slides discussing the mission objectives and design details are at the same level found on typical project outreach websites and in conference papers respectively. The test discussion provides modest detail of an ordinary thermal balance test using mockup hardware. The photographs show an off-Lab vacuum chamber facility with no compromising details.

Endurance test for IR rig for RI production assembly (test procedure)

International Nuclear Information System (INIS)

Chung, Heung June; Ryu, Jeong Soo

2000-08-01

This test procedure details the test loop, test method, and test procedure for pressure drop, vibration and endurance test of IR Rig for RI production. From the pressure drop test, the hydraulic design requirements of the capsule are verified. HANARO limit condition is checked and the compatibility with HANARO core is verified. From flow induced vibration test vibration frequency and displacement are investigated. The wear of IR Rig is investigated through endurance test, and these data are used to evaluate the expected wear at maximum resident time of the IR Rig for RI production

Detailed requirements document for the Interactive Financial Management System (IFMS), volume 1

Science.gov (United States)

Dodson, D. B.

1975-01-01

The detailed requirements for phase 1 (online fund control, subauthorization accounting, and accounts receivable functional capabilities) of the Interactive Financial Management System (IFMS) are described. This includes information on the following: systems requirements, performance requirements, test requirements, and production implementation. Most of the work is centered on systems requirements, and includes discussions on the following processes: resources authority, allotment, primary work authorization, reimbursable order acceptance, purchase request, obligation, cost accrual, cost distribution, disbursement, subauthorization performance, travel, accounts receivable, payroll, property, edit table maintenance, end-of-year, backup input. Other subjects covered include: external systems interfaces, general inquiries, general report requirements, communication requirements, and miscellaneous. Subjects covered under performance requirements include: response time, processing volumes, system reliability, and accuracy. Under test requirements come test data sources, general test approach, and acceptance criteria. Under production implementation come data base establishment, operational stages, and operational requirements.

Specificity and detail in autobiographical memory: Same or different constructs?

Science.gov (United States)

Kyung, Yoonhee; Yanes-Lukin, Paula; Roberts, John E

2016-01-01

Research on autobiographical memory has focused on whether memories are coded as specific (i.e., describe a single event that happened at a particular time and place). Although some theory and research suggests that the amount of detail in autobiographical memories reflects a similar underlying construct as memory specificity, past research has not investigated whether these variables converge. Therefore, the present study compared the proportion of specific memories and the amount of detail embedded in memory responses to cue words. Results demonstrated that memory detail and proportion of specific memories were not correlated with each other and showed different patterns of association with other conceptually relevant variables. When responses to neutral cue words were examined in multiple linear and logistic regression analyses, the proportion of specific memories uniquely predicted less depressive symptoms, low emotional avoidance, lower emotion reactivity, better executive control and lower rumination, whereas the amount of memory detail uniquely predicted the presence of depression diagnosis, as well as greater depressive symptoms, subjective stress, emotion reactivity and rumination. Findings suggest that the ability to retrieve specific memories and the tendency to retrieve detailed personal memories reflect different constructs that have different implications in the development of emotional distress.

Evaluation of a software package for automated quality assessment of contrast detail images-comparison with subjective visual assessment

International Nuclear Information System (INIS)

Pascoal, A; Lawinski, C P; Honey, I; Blake, P

2005-01-01

Contrast detail analysis is commonly used to assess image quality (IQ) associated with diagnostic imaging systems. Applications include routine assessment of equipment performance and optimization studies. Most frequently, the evaluation of contrast detail images involves human observers visually detecting the threshold contrast detail combinations in the image. However, the subjective nature of human perception and the variations in the decision threshold pose limits to the minimum image quality variations detectable with reliability. Objective methods of assessment of image quality such as automated scoring have the potential to overcome the above limitations. A software package (CDRAD analyser) developed for automated scoring of images produced with the CDRAD test object was evaluated. Its performance to assess absolute and relative IQ was compared with that of an average observer. Results show that the software does not mimic the absolute performance of the average observer. The software proved more sensitive and was able to detect smaller low-contrast variations. The observer's performance was superior to the software's in the detection of smaller details. Both scoring methods showed frequent agreement in the detection of image quality variations resulting from changes in kVp and KERMA detector , which indicates the potential to use the software CDRAD analyser for assessment of relative IQ

Simulation of flame-vortex interaction using detailed and reduced

Energy Technology Data Exchange (ETDEWEB)

Hilka, M. [Gaz de France (GDF), 75 - Paris (France); Veynante, D. [Ecole Centrale de Paris, Laboratoire EM2C. CNRS, 92 - Chatenay-Malabry (France); Baum, M. [CERFACS (France); Poinsot, T.J. [Centre National de la Recherche Scientifique (CNRS), 45 - Orleans-la-Source (France). Institut de Mecanique des Fluides de Toulouse

1996-12-31

The interaction between a pair of counter-rotating vortices and a lean premixed CH{sub 4}/O{sub 2}/N{sub 2} flame ({Phi} = + 0.55) has been studied by direct numerical simulations using detailed and reduced chemical reaction schemes. Results from the complex chemistry simulation are discussed with respect to earlier experiments and differences in the simulations using detailed and reduces chemistry are investigated. Transient evolutions of the flame surface and the total heat release rate are compared and modifications in the evolution of the local flame structure are displayed. (authors) 22 refs.

Modeling of a Parabolic Trough Solar Field for Acceptance Testing: A Case Study

Energy Technology Data Exchange (ETDEWEB)

Wagner, M. J.; Mehos, M. S.; Kearney, D. W.; McMahan, A. C.

2011-01-01

As deployment of parabolic trough concentrating solar power (CSP) systems ramps up, the need for reliable and robust performance acceptance test guidelines for the solar field is also amplified. Project owners and/or EPC contractors often require extensive solar field performance testing as part of the plant commissioning process in order to ensure that actual solar field performance satisfies both technical specifications and performance guaranties between the involved parties. Performance test code work is currently underway at the National Renewable Energy Laboratory (NREL) in collaboration with the SolarPACES Task-I activity, and within the ASME PTC-52 committee. One important aspect of acceptance testing is the selection of a robust technology performance model. NREL1 has developed a detailed parabolic trough performance model within the SAM software tool. This model is capable of predicting solar field, sub-system, and component performance. It has further been modified for this work to support calculation at subhourly time steps. This paper presents the methodology and results of a case study comparing actual performance data for a parabolic trough solar field to the predicted results using the modified SAM trough model. Due to data limitations, the methodology is applied to a single collector loop, though it applies to larger subfields and entire solar fields. Special consideration is provided for the model formulation, improvements to the model formulation based on comparison with the collected data, and uncertainty associated with the measured data. Additionally, this paper identifies modeling considerations that are of particular importance in the solar field acceptance testing process and uses the model to provide preliminary recommendations regarding acceptable steady-state testing conditions at the single-loop level.

Case studies in ultrasonic testing

International Nuclear Information System (INIS)

Prasad, V.; Satheesh, C.; Varde, P.V.

2015-01-01

Ultrasonic testing is widely used Non Destructive Testing (NDT) method and forms the essential part of In-service inspection programme of nuclear reactors. Main application of ultrasonic testing is for volumetric scanning of weld joints followed by thickness gauging of pipelines and pressure vessels. Research reactor Dhruva has completed the first In Service Inspection programme in which about 325 weld joints have been volumetrically scanned, in addition to thickness gauging of 300 meters of pipe lines of various sizes and about 24 nos of pressure vessels. Ultrasonic testing is also used for level measurements, distance measurements and cleaning and decontamination of tools. Two case studies are brought out in this paper in which ultrasonic testing is used successfully for identification of butterfly valve opening status and extent of choking in pipe lines in Dhruva reactor systems

The Architectural and Technical Consequences of Different Window Details in a Danish Passive House

DEFF Research Database (Denmark)

Brunsgaard, Camilla; Heiselberg, Per; Jensen, Rasmus Lund

2008-01-01

 This paper focuses on a study of window details from "The Comfort Houses" in relation to "traditional" Danish construction solutions. The aim is to evaluate different ways of solving a window detail and to identify both architectural and technical consequences. It is important to investigate bot...... aspects of a detail because the best technical solution might not be the best architectural solution. A proposal from "The Comfort Houses" - a brick passive house, will be used as a basis....... This paper focuses on a study of window details from "The Comfort Houses" in relation to "traditional" Danish construction solutions. The aim is to evaluate different ways of solving a window detail and to identify both architectural and technical consequences. It is important to investigate both...

Detailed modeling of mountain wave PSCs

Directory of Open Access Journals (Sweden)

S. Fueglistaler

2003-01-01

Full Text Available Polar stratospheric clouds (PSCs play a key role in polar ozone depletion. In the Arctic, PSCs can occur on the mesoscale due to orographically induced gravity waves. Here we present a detailed study of a mountain wave PSC event on 25-27 January 2000 over Scandinavia. The mountain wave PSCs were intensively observed by in-situ and remote-sensing techniques during the second phase of the SOLVE/THESEO-2000 Arctic campaign. We use these excellent data of PSC observations on 3 successive days to analyze the PSCs and to perform a detailed comparison with modeled clouds. We simulated the 3-dimensional PSC structure on all 3 days with a mesoscale numerical weather prediction (NWP model and a microphysical box model (using best available nucleation rates for ice and nitric acid trihydrate particles. We show that the combined mesoscale/microphysical model is capable of reproducing the PSC measurements within the uncertainty of data interpretation with respect to spatial dimensions, temporal development and microphysical properties, without manipulating temperatures or using other tuning parameters. In contrast, microphysical modeling based upon coarser scale global NWP data, e.g. current ECMWF analysis data, cannot reproduce observations, in particular the occurrence of ice and nitric acid trihydrate clouds. Combined mesoscale/microphysical modeling may be used for detailed a posteriori PSC analysis and for future Arctic campaign flight and mission planning. The fact that remote sensing alone cannot further constrain model results due to uncertainities in the interpretation of measurements, underlines the need for synchronous in-situ PSC observations in campaigns.

Further Experiments with Lok-Test and Ultrasonic Test in Relation to Fresh and Hardened Concrete

DEFF Research Database (Denmark)

Jensen, Jens Kristian Jehrbo

Lok-test is mainly a non-destructive pull-out test for determination of concrete strength. The method is deseribed in (l) and it is detailed discussed in theory (2). The method is welknown in practice. Ultrasonic is commonly used for investigations of several materials, especially concrete. In a ....... In a project (3) about non-destructive testing of concrete different methods and the relations to concrete are discussed in theory and practice. This paper point out some interesting results from further experiments in this area.......Lok-test is mainly a non-destructive pull-out test for determination of concrete strength. The method is deseribed in (l) and it is detailed discussed in theory (2). The method is welknown in practice. Ultrasonic is commonly used for investigations of several materials, especially concrete...

Detailed comparison of LIGO and Virgo inspiral pipelines in preparation for a joint search

International Nuclear Information System (INIS)

Beauville, F; Buskulic, D; Grosjean, D; Bizouard, M-A; Cavalier, F; Clapson, A-C; Hello, P; Blackburn, L; Katsavounidis, E; Bosi, L; Brocco, L; Brown, D A; Chatterji, S; Christensen, N; Knight, M; Fairhurst, S; Guidi, G; Heng, S; Hewitson, M; Klimenko, S

2008-01-01

Presented in this paper is a detailed and direct comparison of the detection pipelines used by LIGO and Virgo in their attempt to observe gravitational waves from binary neutron star systems. In order to test the search programs, numerous inspiral signals were added to 24 h of simulated detector data. The efficiencies of the different pipelines were tested, and found to be very similar. Parameter estimation routines were also tested. We demonstrate that there are definite benefits if LIGO and Virgo conduct a joint coincident analysis; these advantages include increased detection efficiency and information on source sky location

Detailed comparison of LIGO and Virgo inspiral pipelines in preparation for a joint search

Energy Technology Data Exchange (ETDEWEB)

Beauville, F; Buskulic, D; Grosjean, D [Laboratoire d' Annecy-le-Vieux de Physique des Particules, Chemin de Bellevue, BP 110, 74941 Annecy-le-Vieux Cedex (France); Bizouard, M-A; Cavalier, F; Clapson, A-C; Hello, P [Laboratoire de l' Accelerateur Lineaire, IN2P3/CNRS-Universite de Paris XI, BP 34, 91898 Orsay Cedex (France); Blackburn, L; Katsavounidis, E [LIGO-Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Bosi, L [INFN Sezione di Perugia and/or Universita di Perugia, Via A Pascoli, I-06123 Perugia (Italy); Brocco, L [INFN Sezione di Roma and/or Universita ' La Sapienza' , P.le A Moro 2, I-00185, Roma (Italy); Brown, D A; Chatterji, S [LIGO-California Institute of Technology, Pasadena, CA 91125 (United States); Christensen, N; Knight, M [Carleton College, Northfield, MN 55057 (United States); Fairhurst, S [University of Wisconsin-Milwaukee, Milwaukee, WI 53201 (United States); Guidi, G [INFN Sezione Firenze/Urbino Via G Sansone 1, I-50019 Sesto Fiorentino (Italy) and/or Universita di Firenze, Largo E.Fermi 2, I-50125 Firenze and/or Universita di Urbino, Via S Chiara 27, I-61029 Urbino (Italy); Heng, S; Hewitson, M [University of Glasgow, Glasgow, G12 8QQ (United Kingdom); Klimenko, S [University of Florida-Gainesville, FL 32611 (United States)] (and others)

2008-02-21

Presented in this paper is a detailed and direct comparison of the detection pipelines used by LIGO and Virgo in their attempt to observe gravitational waves from binary neutron star systems. In order to test the search programs, numerous inspiral signals were added to 24 h of simulated detector data. The efficiencies of the different pipelines were tested, and found to be very similar. Parameter estimation routines were also tested. We demonstrate that there are definite benefits if LIGO and Virgo conduct a joint coincident analysis; these advantages include increased detection efficiency and information on source sky location.

Preparation of acceptance tests and criteria for the Test Blanket Systems to be operated in ITER

Energy Technology Data Exchange (ETDEWEB)

Laan, J.G. van der, E-mail: JaapG.vanderLaan@iter.org [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Cuquel, B. [AIRBUS Defence and Space S.A.S., 13115 Saint Paul Lez Durance (France); Demange, D.; Ghidersa, B.-E. [Karlsruhe Institute of Technology, Karlsruhe (Germany); Giancarli, L.M.; Iseli, M.; Jourdan, T. [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France); Nevière, J.-C. [Comex-Nucleaire, 13115 Saint Paul Lez Durance (France); Pascal, R.; Ring, W. [ITER Organization, Route de Vinon sur Verdon, CS 90 046, 13067 St Paul Lez Durance Cedex (France)

2015-10-15

Highlights: • Initial guideline for acceptance testing and acceptance criteria for Test Blanket Systems in ITER. • These tests complement those required by the applicable codes and standards, and regulations. • Completion of TBS manufacture will be followed by Factory Acceptance Testing, prior to shipment. • Next steps are “Reception Inspection Tests”, and on-site pre-installation and components tests. • This guideline allows the detailing of the TBS specific test plans and their scheduling. - Abstract: This paper describes the main acceptance criteria and required acceptance tests for the components of the six Test Blanket Systems to be installed and operated in ITER. It summarizes the guide-line toward the establishment of detailed test plans for the TBS, starting from the end-product at the ITER Members factories, and to generally define the type of tests that have to be performed on the ITER site after shipment, and/or prior to the systems final commissioning phase.

Detailed Soils 24K

Data.gov (United States)

Kansas Data Access and Support Center — This data set is a digital soil survey and is the most detailed level of soil geographic data developed by the National Cooperative Soil Survey. The information was...

Detailed Facility Report Data Dictionary | ECHO | US EPA

Science.gov (United States)

The Detailed Facility Report Data Dictionary provides users with a list of the variables and definitions that have been incorporated into the Detailed Facility Report. The Detailed Facility Report provides a concise enforcement and compliance history for a facility.

Correlation of analysis with high level vibration test results for primary coolant piping

International Nuclear Information System (INIS)

Park, Y.J.; Hofmayer, C.H.; Costello, J.F.

1992-01-01

Dynamic tests on a modified 1/2.5-scale model of pressurized water reactor (PWR) primary coolant piping were performed using a large shaking table at Tadotsu, Japan. The High Level Vibration Test (HLVT) program was part of a cooperative study between the United States (Nuclear Regulatory Commission/Brookhaven National Laboratory, NRC/BNL) and Japan (Ministry of International Trade and Industry/Nuclear Power Engineering Center). During the test program, the excitation level of each test run was gradually increased up to the limit of the shaking table and significant plastic strains, as well as cracking, were induced in the piping. To fully utilize the test results, NRC/BNL sponsored a project to develop corresponding analytical predictions for the nonlinear dynamic response of the piping for selected test runs. The analyses were performed using both simplified and detailed approaches. The simplified approaches utilize a linear solution and an approximate formulation for nonlinear dynamic effects such as the use of a deamplification factor. The detailed analyses were performed using available nonlinear finite element computer codes, including the MARC, ABAQUS, ADINA and WECAN codes. A comparison of various analysis techniques with the test results shows a higher prediction error in the detailed strain values in the overall response values. A summary of the correlation analyses was presented before the BNL. This paper presents a detailed description of the various analysis results and additional comparisons with test results

The Stimulus test stand

International Nuclear Information System (INIS)

Christofek, L.; Rapidis, P.; Reinhard, A.; Fermilab

2005-01-01

The Stimulus Test Stand was originally constructed and assembled for testing the SVX2 ASIC readout and then upgraded for SVX3 ASIC prototyping and testing. We have modified this system for SVX4 ASIC [1] prototype testing. We described the individual components below. Additional details for other hardware for SVX4 testing can be found in reference [2]. We provide a description of the Stimulus Test Stand used for prototype testing of the SVX4 chip

Recovering and Preventing Loss of Detailed Memory: Differential Rates of Forgetting for Detail Types in Episodic Memory

Science.gov (United States)

Sekeres, Melanie J.; Bonasia, Kyra; St-Laurent, Marie; Pishdadian, Sara; Winocur, Gordon; Grady, Cheryl; Moscovitch, Morris

2016-01-01

Episodic memories undergo qualitative changes with time, but little is known about how different aspects of memory are affected. Different types of information in a memory, such as perceptual detail, and central themes, may be lost at different rates. In patients with medial temporal lobe damage, memory for perceptual details is severely impaired,…

Making detailed predictions makes (some) predictions worse

Science.gov (United States)

Kelly, Theresa F.

In this paper, we investigate whether making detailed predictions about an event makes other predictions worse. Across 19 experiments, 10,895 participants, and 415,960 predictions about 724 professional sports games, we find that people who made detailed predictions about sporting events (e.g., how many hits each baseball team would get) made worse predictions about more general outcomes (e.g., which team would win). We rule out that this effect is caused by inattention or fatigue, thinking too hard, or a differential reliance on holistic information about the teams. Instead, we find that thinking about game-relevant details before predicting winning teams causes people to give less weight to predictive information, presumably because predicting details makes information that is relatively useless for predicting the winning team more readily accessible in memory and therefore incorporated into forecasts. Furthermore, we show that this differential use of information can be used to predict what kinds of games will and will not be susceptible to the negative effect of making detailed predictions.

Face Perception and Test Reliabilities in Congenital Prosopagnosia in Seven Tests

Directory of Open Access Journals (Sweden)

Janina Esins

2016-01-01

Full Text Available Congenital prosopagnosia, the innate impairment in recognizing faces, is a very heterogeneous disorder with different phenotypical manifestations. To investigate the nature of prosopagnosia in more detail, we tested 16 prosopagnosics and 21 controls with an extended test battery addressing various aspects of face recognition. Our results show that prosopagnosics exhibited significant impairments in several face recognition tasks: impaired holistic processing (they were tested amongst others with the Cambridge Face Memory Test (CFMT as well as reduced processing of configural information of faces. This test battery also revealed some new findings. While controls recognized moving faces better than static faces, prosopagnosics did not exhibit this effect. Furthermore, prosopagnosics had significantly impaired gender recognition—which is shown on a groupwise level for the first time in our study. There was no difference between groups in the automatic extraction of face identity information or in object recognition as tested with the Cambridge Car Memory Test. In addition, a methodological analysis of the tests revealed reduced reliability for holistic face processing tests in prosopagnosics. To our knowledge, this is the first study to show that prosopagnosics showed a significantly reduced reliability coefficient (Cronbach’s alpha in the CFMT compared to the controls. We suggest that compensatory strategies employed by the prosopagnosics might be the cause for the vast variety of response patterns revealed by the reduced test reliability. This finding raises the question whether classical face tests measure the same perceptual processes in controls and prosopagnosics.

COMPARISON OF UPPER LIP BITE TEST WITH MODIFIED MALLAMPATI TEST AND THYROMENTAL DISTANCE FOR PREDICTING DIFFICULTY IN ENDOTRACHEAL INTUBATION: A PROSPECTIVE STUDY

Directory of Open Access Journals (Sweden)

Prakash T. S. N

2016-09-01

Full Text Available BACKGROUND The significance of difficult or failed tracheal intubation was well recognised as a major cause of morbidity and mortality in anaesthetic practice as per ASA closed claim study. The need to predict potentially difficult tracheal intubation has received more importance, but with limited success. Unanticipated difficult intubation is a risk to patient’s life and a challenge to the skill of the anaesthesiologist. Many anatomical and pathological variables have been identified and have been suggested to be useful in anticipating a difficult airway. These factors have limitations because of wide variations in the incidence of difficult intubation, interobserver variability and inadequate statistical power of the currently measured variables. METHODS After obtaining institutional ethical committee clearance and written informed consent, the present study was conducted in 200 patients aged between 16 yrs. and 65 yrs. at King George Hospital, Andhra Medical College, Visakhapatnam, in the Department of Anaesthesiology. All the 200 patients undergoing elective surgical procedures under general anaesthesia were enrolled in the study. A thorough preanaesthetic evaluation was carried out in all the patients and the procedure was explained in detail to the patients. RESULTS Of the entire two hundred patients, a total of ten patients had difficult intubation, all of them had Cormack-Lehane class III on laryngoscopy. None of them had Cormack-Lehane class IV on laryngoscopy. The incidence of difficult intubation was 5% in the present study. There were no cases of failed intubation. One hundred and eighty seven patients predicted to be easy for intubation by ULBT (i.e. patients who had ULBT class I and II out of whom, however, we encountered difficult intubation in 5 patients. Out of the eight patients predicted to have difficult airway by ULBT III, only one patient had CL III difficult airway and subsequently difficult intubation. CONCLUSIONS MMT

Aging Depth Test of Rubber Blocks by Accelerated Thermal Oxidation Test

International Nuclear Information System (INIS)

Park, Junhee; Choun, Young-Sun; Kim, Min Kyu

2015-01-01

In this study, the accelerated thermal oxidation tests of rubber block were performed to investigate the aging depth of rubber bearing. From the tests, it was found the critical aging depth in rubber block. Also the property variation of rubber was investigated along the depth. The deterioration pattern from the aging depth tests was found from surface to inside and the critical aging depth was to be about 10 mm. The analytical model for rubber bearing with aging can be developed based on the relationship between the property variation and aging depth investigated from this study. The mechanical properties of rubber bearings were changed with time. Because the aging effect of rubber material was generally higher than that of other structure materials it is needed that the aging properties of seismically isolators should be evaluated to ensure the safety of seismically isolated nuclear power plants (NPPs) over the lifetime. NRC and ASCE required the tests of seismically isolators for investigating the aging properties. JNES also required the seismic response analysis for the seismically isolated NPPs when the properties of seismically isolators were extremely changed. If the aging properties of seismically isolators such as rubber bearings are evaluated by analysis the analytical model of seismically isolators should be developed considering aging effect of rubber material. From the previous research, it was reported that the behavior of aged rubber material mainly affected by temperature and oxidation. The material properties between surface and inside can be different by the oxidation of rubber. Therefore, the aging depth should be investigated for exactly evaluating the seismic behavior of aged rubber bearing. The aging depth of rubber baring was not influenced by the size of seismically isolators but environment condition. Therefore, the detail analysis considering aging depth was not required for NPPs with large seismically isolators. But the seismic response

Phase III Simplified Integrated Test (SIT) results - Space Station ECLSS testing

Science.gov (United States)

Roberts, Barry C.; Carrasquillo, Robyn L.; Dubiel, Melissa Y.; Ogle, Kathryn Y.; Perry, Jay L.; Whitley, Ken M.

1990-01-01

During 1989, phase III testing of Space Station Freedom Environmental Control and Life Support Systems (ECLSS) began at Marshall Space Flight Center (MSFC) with the Simplified Integrated Test. This test, conducted at the MSFC Core Module Integration Facility (CMIF), was the first time the four baseline air revitalization subsystems were integrated together. This paper details the results and lessons learned from the phase III SIT. Future plans for testing at the MSFC CMIF are also discussed.

Guide to dataflow supercomputing basic concepts, case studies, and a detailed example

CERN Document Server

Milutinovic, Veljko; Trifunovic, Nemanja; Giorgi, Roberto

2015-01-01

This unique text/reference describes an exciting and novel approach to supercomputing in the DataFlow paradigm. The major advantages and applications of this approach are clearly described, and a detailed explanation of the programming model is provided using simple yet effective examples. The work is developed from a series of lecture courses taught by the authors in more than 40 universities across more than 20 countries, and from research carried out by Maxeler Technologies, Inc. Topics and features: presents a thorough introduction to DataFlow supercomputing for big data problems; revie

Surface-based test plan, Deaf Smith County, Texas Site: Draft

International Nuclear Information System (INIS)

1985-01-01

The Surface-Based Test Plan (SBTP) is the plan which accounts for all surface-based site field work to be conducted at the Permian salt site selected for characterization. The SBTP relates data needs from program requirement documents and presents plans to satisfy the data needs. The SBTP excludes plans for construction of the Exploratory Shaft Facility (ESF) and plans for the in situ testing. The SBTP is a hierarchical plan stemming from the Technical Program Plan. The SBTP describes in detail the process by which surface-based study plans are defined, developed, and controlled. The plans hierarchy extends downward thru subordinate Site Study Plans (SSPs), which describe in detail elements of field work to be done, to detailed Procedures which document the exact methodologies to be employed in the conduct of field work. The plan is a QA level S document, although some of its elements are at lower QA levels. The plan is a controlled document, and any proposed amendments to the plan or subordinate documents can only be implemented through the specified change control procedure

Detailed analysis of radon flux studies at Australian uranium projects

International Nuclear Information System (INIS)

Mudd, Gavin M.

2005-01-01

The release of radon gas and radon progeny from uranium projects is a major issue during operation as well as for the design of rehabilitation works. In Australia, there have been a number of premining radon flux studies as part of the environmental investigation and potential development of recent uranium projects. There is also an increasing amount of operational data on radon fluxes and loads from various aspects of projects, such as tailings, waste rock and mills. Thus there exists much useful measured data which can be used to assess the design radon flux and load targets for rehabilitation. The main projects for which radon data exists includes Ranger, Olympic Dam, Beverley, Honeymoon, Jabiluka, Yeelirrie, Lake Way, Koongarra, Moline, Coronation Hill, Rockhole, Nabarlek, Rum Jungle, Port Pirie and Ben Lomond. To date, much of this data has not been systematically evaluated. The need to compile and assess this data is twofold. Firstly, to assess the loads released from uranium production as an input into life-cycle analyses of the nuclear fuel cycle, such as those undertaken by UNSCEAR and industry groups. Secondly, there is a need to set suitable design standards for radon flux for the rehabilitation of former and current uranium projects. This paper will present such a detailed compilation of radon fluxes and loads which can then be used as the basis for both life-cycle analyses as well as setting appropriate site-specific rehabilitation criteria for radon. The implications for former and current projects is then discussed as well as future data needs. Ultimately, there is a critical need for thorough baseline surveys prior to mining to ensure accurate assessments of changes to radon fluxes and loads. The data and analysis presented is considered applicable to all uranium projects in Australia, as well as being a useful model for considering such issues internationally

Qualification tests for a dosimetry system

International Nuclear Information System (INIS)

Anon.

2005-01-01

The report of qualification tests for personnel dosemeters is detailed. Qualification test for the energy response and the incidence angle is given. The procedure of test is resumed. Different coefficients of conversion used in these tests are given in tables. (N.C.)

Anatomically detailed and large-scale simulations studying synapse loss and synchrony using NeuroBox

Directory of Open Access Journals (Sweden)

Markus eBreit

2016-02-01

Full Text Available The morphology of neurons and networks plays an important role in processing electrical and biochemical signals. Based on neuronal reconstructions, which are becoming abundantly available through databases such as NeuroMorpho.org, numerical simulations of Hodgkin-Huxley-type equations, coupled to biochemical models, can be performed in order to systematically investigate the influence of cellular morphology and the connectivity pattern in networks on the underlying function. Development in the area of synthetic neural network generation and morphology reconstruction from microscopy data has brought forth the software tool NeuGen. Coupling this morphology data (either from databases, synthetic or reconstruction to the simulation platform UG 4 (which harbors a neuroscientific portfolio and VRL-Studio, has brought forth the extendible toolbox NeuroBox. NeuroBox allows users to perform numerical simulations on hybrid-dimensional morphology representations. The code basis is designed in a modular way, such that e.g. new channel or synapse types can be added to the library. Workflows can be specified through scripts or through the VRL-Studio graphical workflow representation. Third-party tools, such as ImageJ, can be added to NeuroBox workflows. In this paper, NeuroBox is used to study the electrical and biochemical effects of synapse loss vs. synchrony in neurons, to investigate large morphology data sets within detailed biophysical simulations, and used to demonstrate the capability of utilizing high-performance computing infrastructure for large scale network simulations. Using new synapse distribution methods and Finite Volume based numerical solvers for compartment-type models, our results demonstrate how an increase in synaptic synchronization can compensate synapse loss at the electrical and calcium level, and how detailed neuronal morphology can be integrated in large-scale network simulations.

Testing of Mortar Systems

Science.gov (United States)

2010-03-11

IEP /TDP) or Independent Assessment Plan (IAP), and the test item and the procedures as outlined in this TOP. The following must also be considered...Command DTIC = Defense Technical Information Center DTP = Detailed Test Plan IAP = Independent Assessment Plan IEP = Independent Evaluation Plan IPT

Dynamic characteristics of lead rubber bearings with dynamic two-dimensional test equipment

International Nuclear Information System (INIS)

Ohtori, Y.; Ishida, K.; Mazda, T.

1994-01-01

Although studies have previously been done on the static mechanical properties of lead rubber bearings, this study aims to grasp the dynamic characteristics of lead rubber bearings from experimental results, using two-dimensional dynamic test equipment which is designed to grasp in detail such dynamic characteristics as deformation capacity and proof stress. This paper describes the results from three types of tests: (1) dynamic mechanical properties tests, (2) cyclic loading tests, and (3) dynamic ultimate tests. Through these tests, it was confirmed that the dynamic characteristics of lead rubber bearings are independent of strain rate

Detailed Design and Fabrication Method of the ITER Vacuum Vessel Ports

International Nuclear Information System (INIS)

Hee-Jae Ahn; Kwon, T.H.; Hong, Y.S.

2006-01-01

The engineering design of the ITER vacuum vessel (VV) has been progressed by the ITER International Team (IT) with the cooperation of several participant teams (PT). The VV and ports are the components allocated to Korea for the construction of the ITER. Hyundai Heavy Industries has been involved in the structural analysis, detailed design and development of the fabrication method of the upper and lower ports within the framework of the ITER transitional arrangements (ITA). The design of the port structures has been investigated to validate and to improve the conceptual designs of the ITER IT and other PT. The special emphasis was laid on the flange joint between the port extension and the in-port plug to develop the design of the upper port. The modified design with a pure friction type flange with forty-eight pieces of bolts instead of the tangential key is recommended. Furthermore, the alternative flange designs developed by the ITER IT have been analyzed in detail to simplify the lip seal maintenance into the port flange. The structural analyses of the lower RH port have been also performed to verify the capacity for supporting the VV. The maximum stress exceeds the allowable value at the reinforcing block and basement. More elaborate local models have been developed to mitigate the stress concentration and to modify the component design. The fabrication method and the sequence of the detailed fabrication for the ports are developed focusing on the cost reduction as well as the simplification. A typical port structure includes a port stub, a stub extension and a port extension with a connecting duct. The fabrication sequence consists of surface treatment, cutting, forming, cleaning, welding, machining, and non-destructive inspection and test. Tolerance study has been performed to avoid the mismatch of each fabricated component and to obtain the suitable tolerances in the assembly at the shop and site. This study is based on the experience in the fabrication of

MFTF test coil construction and performance

International Nuclear Information System (INIS)

Cornish, D.N.; Zbasnik, J.P.; Leber, R.L.; Hirzel, D.G.; Johnston, J.E.; Rosdahl, A.R.

1978-01-01

A solenoid coil, 105 cm inside the 167 cm outside diameter, has been constructed and tested to study the performance of the stabilized Nb--Ti conductor to be used in the Mirror Fusion Test Facility (MFTF) being built at Lawrence Livermore Laboratory. The insulation system of the test coil is identical to that envisioned for MFTF. Cold-weld joints were made in the conductor at the start and finish of each layer; heaters were fitted to some of these joints and also to the conductor at various locations in the winding. This paper gives details of the construction of the coil and the results of the tests carried out to determine its propagation and recovery characteristics

Contextual consistency facilitates long-term memory of perceptual detail in barely seen images.

Science.gov (United States)

Gronau, Nurit; Shachar, Meytal

2015-08-01

It is long known that contextual information affects memory for an object's identity (e.g., its basic level category), yet it is unclear whether schematic knowledge additionally enhances memory for the precise visual appearance of an item. Here we investigated memory for visual detail of merely glimpsed objects. Participants viewed pairs of contextually related and unrelated stimuli, presented for an extremely brief duration (24 ms, masked). They then performed a forced-choice memory-recognition test for the precise perceptual appearance of 1 of 2 objects within each pair (i.e., the "memory-target" item). In 3 experiments, we show that memory-target stimuli originally appearing within contextually related pairs are remembered better than targets appearing within unrelated pairs. These effects are obtained whether the target is presented at test with its counterpart pair object (i.e., when reiterating the original context at encoding) or whether the target is presented alone, implying that the contextual consistency effects are mediated predominantly by processes occurring during stimulus encoding, rather than during stimulus retrieval. Furthermore, visual detail encoding is improved whether object relations involve implied action or not, suggesting that, contrary to some prior suggestions, action is not a necessary component for object-to-object associative "grouping" processes. Our findings suggest that during a brief glimpse, but not under long viewing conditions, contextual associations may play a critical role in reducing stimulus competition for attention selection and in facilitating rapid encoding of sensory details. Theoretical implications with respect to classic frame theories are discussed. (PsycINFO Database Record (c) 2015 APA, all rights reserved).

Non- or full-laxative CT colonography vs. endoscopic tests for colorectal cancer screening: A randomised survey comparing public perceptions and intentions to undergo testing

Energy Technology Data Exchange (ETDEWEB)

Ghanouni, Alex; Wardle, Jane; Von Wagner, Christian [University College London, Health Behaviour Research Centre, Department of Epidemiology and Public Health, London (United Kingdom); Halligan, Steve; Plumb, Andrew; Boone, Darren [University College London, Centre for Medical Imaging, London (United Kingdom)

2014-07-15

Compare public perceptions and intentions to undergo colorectal cancer screening tests following detailed information regarding CT colonography (CTC; after non-laxative preparation or full-laxative preparation), optical colonoscopy (OC) or flexible sigmoidoscopy (FS). A total of 3,100 invitees approaching screening age (45-54 years) were randomly allocated to receive detailed information on a single test and asked to return a questionnaire. Outcomes included perceptions of preparation and test tolerability, health benefits, sensitivity and specificity, and intention to undergo the test. Six hundred three invitees responded with valid questionnaire data. Non-laxative preparation was rated more positively than enema or full-laxative preparations [effect size (r) = 0.13 to 0.54; p < 0.0005 to 0.036]; both forms of CTC and FS were rated more positively than OC in terms of test experience (r = 0.26 to 0.28; all p-values < 0.0005). Perceptions of health benefits, sensitivity and specificity (p = 0.250 to 0.901), and intention to undergo the test (p = 0.213) did not differ between tests (n = 144-155 for each test). Despite non-laxative CTC being rated more favourably, this study did not find evidence that offering it would lead to substantially higher uptake than full-laxative CTC or other methods. However, this study was limited by a lower than anticipated response rate. (orig.)

Investigating the Interaction of Graphic Organizers and Seductive Details: Can a Graphic Organizer Mitigate the Seductive-Details Effect?

Science.gov (United States)

Rowland-Bryant, Emily; Skinner, Christopher H.; Skinner, Amy L.; Saudargas, Richard; Robinson, Daniel H.; Kirk, Emily R.

2009-01-01

The interaction between seductive details (SD) and a graphic organizer (GO) was investigated. Undergraduate students (n = 207) read a target-material passage about Freud's psychosexual stages. Depending on condition, the participants also read a biographical paragraph (SD-only), viewed a graphic organizer that linked the seductive details to the…

Key Features of Academic Detailing: Development of an Expert Consensus Using the Delphi Method.

Science.gov (United States)

Yeh, James S; Van Hoof, Thomas J; Fischer, Michael A

2016-02-01

Academic detailing is an outreach education technique that combines the direct social marketing traditionally used by pharmaceutical representatives with unbiased content summarizing the best evidence for a given clinical issue. Academic detailing is conducted with clinicians to encourage evidence-based practice in order to improve the quality of care and patient outcomes. The adoption of academic detailing has increased substantially since the original studies in the 1980s. However, the lack of standard agreement on its implementation makes the evaluation of academic detailing outcomes challenging. To identify consensus on the key elements of academic detailing among a group of experts with varying experiences in academic detailing. This study is based on an online survey of 20 experts with experience in academic detailing. We used the Delphi process, an iterative and systematic method of developing consensus within a group. We conducted 3 rounds of online surveys, which addressed 72 individual items derived from a previous literature review of 5 features of academic detailing, including (1) content, (2) communication process, (3) clinicians targeted, (4) change agents delivering intervention, and (5) context for intervention. Nonrespondents were removed from later rounds of the surveys. For most questions, a 4-point ordinal scale was used for responses. We defined consensus agreement as 70% of respondents for a single rating category or 80% for dichotomized ratings. The overall survey response rate was 95% (54 of 57 surveys) and nearly 92% consensus agreement on the survey items (66 of 72 items) by the end of the Delphi exercise. The experts' responses suggested that (1) focused clinician education offering support for clinical decision-making is a key component of academic detailing, (2) detailing messages need to be tailored and provide feasible strategies and solutions to challenging cases, and (3) academic detailers need to develop specific skill sets

Field testing plan for unsaturated zone monitoring and field studies

International Nuclear Information System (INIS)

Young, M.H.; Wierenga, P.J.; Warrick, A.W.

1996-10-01

The University of Arizona, in cooperation with the Bureau of Economic Geology at The University of Texas at Austin, and Stephens and Associates in Albuquerque, New Mexico has developed a field testing plan for evaluating subsurface monitoring systems. The U.S. Nuclear Regulatory Commission has requested development of these testing plans for low-level radioactive waste disposal sites (LLW) and for monitoring at decommissioned facilities designated under the open-quotes Site Decommissioning Management Planclose quotes (SDMP). The tests are conducted on a 50 m by 50 m plot on the University of Arizona's Maricopa Agricultural Center. Within the 50 m by 50 m plot one finds: (1) an instrumented buried trench, (2) monitoring islands similar to those proposed for the Ward Valley, California LLW Facility, (3) deep borehole monitoring sites, (4) gaseous transport monitoring, and (5) locations for testing non-invasive geophysical measurement techniques. The various subplot areas are instrumented with commercially available instruments such as neutron probes, time domain reflectometry probes, tensiometers, psychrometers, heat dissipation sensors, thermocouples, solution samplers, and cross-hole geophysics electrodes. Measurement depths vary from ground surface to 15 m. The data from the controlled flow and transport experiments, conducted over the plot, will be used to develop an integrated approach to long-term monitoring of the vadose zone at waste disposal sites. The data will also be used to test field-scale flow and transport models. This report describes in detail the design of the experiment and the methodology proposed for evaluating the data

Implementing academic detailing for breast cancer screening in underserved communities

Directory of Open Access Journals (Sweden)

Ashford Alfred R

2007-12-01

Full Text Available Abstract Background African American and Hispanic women, such as those living in the northern Manhattan and the South Bronx neighborhoods of New York City, are generally underserved with regard to breast cancer prevention and screening practices, even though they are more likely to die of breast cancer than are other women. Primary care physicians (PCPs are critical for the recommendation of breast cancer screening to their patients. Academic detailing is a promising strategy for improving PCP performance in recommending breast cancer screening, yet little is known about the effects of academic detailing on breast cancer screening among physicians who practice in medically underserved areas. We assessed the effectiveness of an enhanced, multi-component academic detailing intervention in increasing recommendations for breast cancer screening within a sample of community-based urban physicians. Methods Two medically underserved communities were matched and randomized to intervention and control arms. Ninety-four primary care community (i.e., not hospital based physicians in northern Manhattan were compared to 74 physicians in the South Bronx neighborhoods of the New York City metropolitan area. Intervention participants received enhanced physician-directed academic detailing, using the American Cancer Society guidelines for the early detection of breast cancer. Control group physicians received no intervention. We conducted interviews to measure primary care physicians' self-reported recommendation of mammography and Clinical Breast Examination (CBE, and whether PCPs taught women how to perform breast self examination (BSE. Results Using multivariate analyses, we found a statistically significant intervention effect on the recommendation of CBE to women patients age 40 and over; mammography and breast self examination reports increased across both arms from baseline to follow-up, according to physician self-report. At post-test, physician

Detailed-term-accounting approximation calculations of the radiative opacity of aluminum plasmas: A systematic study

International Nuclear Information System (INIS)

Zeng Jiaolong; Yuan Jianmin

2002-01-01

The spectrally resolved radiative opacity and the Rosseland and Planck mean opacities are calculated by using the detailed-term-accounting approximation for aluminum plasmas with varieties of density and temperature. The results are presented along a 40 eV isothermal sequence, a 0.01 g/cm 3 isodense sequence, and a sequence with average ionization degree Z*∼7.13. Particular attention is given to the influence of the detailed treatment of spectral lines on the Rosseland mean opacity under different thermodynamical conditions. The results show that at densities of 0.004 g/cm 3 and higher, the opacities are not very sensitive to the spectral linewidth within a reasonable range. As examples, the Rosseland mean opacity, which is most sensitive to the detailed linewidth, at 40 eV and 0.004 g/cm 3 changes no more than 15%, when we change the electron impact spectral linewidth artificially by reducing it by 50% or increasing it twice, and at 40 eV and 0.1 g/cm 3 it changes less than 5%. For comparison, we also carried out calculations by using an average atom model. For the Rosseland mean opacities, the two models show quite large differences, in particular at low densities, while for the Planck mean opacities the results of the two models are much closer

The MuCool Test Area and RF Program

International Nuclear Information System (INIS)

Torun, Y.; Huang, D.; Norem, J.; Palmer, Robert B.; Stratakis, Diktys; Bross, A.; Chung, M.; Jansson, A.; Moretti, A.; Yonehara, K.; Li, D.

2010-01-01

The MuCool RF Program focuses on the study of normal conducting RF structures operating in high magnetic field for applications in muon ionization cooling for Neutrino Factories and Muon Colliders. Here we give an overview of the program, which includes a description of the test facility and its capabilities, the current test program, and the status of a cavity that can be rotated in the magnetic field, which allows for a detailed study of the maximum stable operating gradient vs. magnetic field strength and angle.

Detailed behavioral modeling of bang-bang phase detectors

DEFF Research Database (Denmark)

Jiang, Chenhui; Andreani, Pietro; Keil, U. D.

2006-01-01

In this paper, the metastability of current-mode logic (CML) latches and flip-flops is studied in detail. Based on the results of this analysis, a behavioral model of bang-bang phase detectors (BBPDs) is proposed, which is able to reliably capture the critical deadzone effect. The impact of jitter...

FY 2016 Status Report: CIRFT Testing on Spent Nuclear Fuels and Hydride Reorientation Study

Energy Technology Data Exchange (ETDEWEB)

Wang, Jy-An John [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Wang, Hong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Yan, Yong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Bevard, Bruce B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Scaglione, John M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division

2016-08-04

This report provides a detailed description of the Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) testing conducted on spent nuclear fuel (SNF) rods in FY 2016, including hydride reorientation test results. Contact-based measurement, or three-LVDT-based curvature measurement, of SNF rods has proven to be quite reliable in CIRFT testing. However, how the linear variable differential transformer (LVDT) head contacts the SNF rod may have a significant effect on the curvature measurement, depending on the magnitude and direction of rod curvature. To correct such contact/curvature issues, sensor spacing, defined as the amount of separation between the three LVDT probes, is a critical measurement that can be used to calculate rod curvature once the deflections are obtained. Recently developed CIRFT data analyses procedures were integrated into FY 2016 CIRFT testing results for the curvature measurements. The variations in fatigue life are provided in terms of moment, equivalent stress, curvature, and equivalent strain for the tested SNFs. The equivalent stress plot collapsed the data points from all of the SNFs into a single zone. A detailed examination revealed that, at same stress level, fatigue lives display a descending order as follows: H. B. Robinson Nuclear Power Station (HBR), Limerick Nuclear Power Station (LMK), mixed uranium-plutonium oxide (MOX). If looking at the strain, then LMK fuel has a slightly longer fatigue life than HBR fuel, but the difference is subtle. The knee point of endurance limit in the curve of moment and curvature or equivalent quantities is more clearly defined for LMK and HBR fuels. The treatment affects the fatigue life of specimens. Both a drop of 12 in. and radial hydride treatment (RHT) have a negative impact on fatigue life. The effect of thermal annealing on MOX fuel rods was relatively small at higher amplitude but became significant at low amplitude of moment. Thermal annealing tended to extend the fatigue life of

Coupled Dictionary Learning for the Detail-Enhanced Synthesis of 3-D Facial Expressions.

Science.gov (United States)

Liang, Haoran; Liang, Ronghua; Song, Mingli; He, Xiaofei

2016-04-01

The desire to reconstruct 3-D face models with expressions from 2-D face images fosters increasing interest in addressing the problem of face modeling. This task is important and challenging in the field of computer animation. Facial contours and wrinkles are essential to generate a face with a certain expression; however, these details are generally ignored or are not seriously considered in previous studies on face model reconstruction. Thus, we employ coupled radius basis function networks to derive an intermediate 3-D face model from a single 2-D face image. To optimize the 3-D face model further through landmarks, a coupled dictionary that is related to 3-D face models and their corresponding 3-D landmarks is learned from the given training set through local coordinate coding. Another coupled dictionary is then constructed to bridge the 2-D and 3-D landmarks for the transfer of vertices on the face model. As a result, the final 3-D face can be generated with the appropriate expression. In the testing phase, the 2-D input faces are converted into 3-D models that display different expressions. Experimental results indicate that the proposed approach to facial expression synthesis can obtain model details more effectively than previous methods can.

Contrast to Noise Ratio and Contrast Detail Analysis in Mammography:A Monte Carlo Study

International Nuclear Information System (INIS)

Metaxas, V; Delis, H; Panayiotakis, G; Kalogeropoulou, C; Zampakis, P

2015-01-01

The mammographic spectrum is one of the major factors affecting image quality in mammography. In this study, a Monte Carlo (MC) simulation model was used to evaluate image quality characteristics of various mammographic spectra. The anode/filter combinations evaluated, were those traditionally used in mammography, for tube voltages between 26 and 30 kVp. The imaging performance was investigated in terms of Contrast to Noise Ratio (CNR) and Contrast Detail (CD) analysis, by involving human observers, utilizing a mathematical CD phantom. Soft spectra provided the best characteristics in terms of both CNR and CD scores, while tube voltage had a limited effect. W-anode spectra filtered with k-edge filters demonstrated an improved performance, that sometimes was better compared to softer x-ray spectra, produced by Mo or Rh anode. Regarding the filter material, k-edge filters showed superior performance compared to Al filters. (paper)

Testing the standard model

International Nuclear Information System (INIS)

Gordon, H.; Marciano, W.; Williams, H.H.

1982-01-01

We summarize here the results of the standard model group which has studied the ways in which different facilities may be used to test in detail what we now call the standard model, that is SU/sub c/(3) x SU(2) x U(1). The topics considered are: W +- , Z 0 mass, width; sin 2 theta/sub W/ and neutral current couplings; W + W - , Wγ; Higgs; QCD; toponium and naked quarks; glueballs; mixing angles; and heavy ions

Measuring Detailed Chemical Abundances from Co-added Medium-resolution Spectra. I. Tests Using Milky Way Dwarf Spheroidal Galaxies and Globular Clusters

Science.gov (United States)

Yang, Lei; Kirby, Evan N.; Guhathakurta, Puragra; Peng, Eric W.; Cheng, Lucy

2013-05-01

The ability to measure metallicities and α-element abundances in individual red giant branch (RGB) stars using medium-resolution spectra (R ≈ 6000) is a valuable tool for deciphering the nature of Milky Way dwarf satellites and the history of the Galactic halo. Extending such studies to more distant systems like Andromeda is beyond the ability of the current generation of telescopes, but by co-adding the spectra of similar stars, we can attain the necessary signal-to-noise ratio (S/N) to make detailed abundance measurements. In this paper, we present a method to determine metallicities and α-element abundances using the co-addition of medium-resolution spectra. We test the method of spectral co-addition using high-S/N spectra of more than 1300 RGB stars from Milky Way globular clusters and dwarf spheroidal galaxies obtained with the Keck II telescope/DEIMOS spectrograph. We group similar stars using photometric criteria and compare the weighted ensemble average abundances ([Fe/H], [Mg/Fe], [Si/Fe], [Ca/Fe], and [Ti/Fe]) of individual stars in each group with the measurements made on the corresponding co-added spectrum. We find a high level of agreement between the two methods, which permits us to apply this co-added spectra technique to more distant RGB stars, like stars in the M31 satellite galaxies. This paper outlines our spectral co-addition and abundance measurement methodology and describes the potential biases in making these measurements. Data herein were obtained at the W. M. Keck Observatory, which is operated as a scientific partnership among the California Institute of Technology, the University of California, and NASA. The Observatory was made possible by the generous financial support of the W. M. Keck Foundation.

External details revisited - A new taxonomy for coding 'non-episodic' content during autobiographical memory retrieval.

Science.gov (United States)

Strikwerda-Brown, Cherie; Mothakunnel, Annu; Hodges, John R; Piguet, Olivier; Irish, Muireann

2018-04-24

Autobiographical memory (ABM) is typically held to comprise episodic and semantic elements, with the vast majority of studies to date focusing on profiles of episodic details in health and disease. In this context, 'non-episodic' elements are often considered to reflect semantic processing or are discounted from analyses entirely. Mounting evidence suggests that rather than reflecting one unitary entity, semantic autobiographical information may contain discrete subcomponents, which vary in their relative degree of semantic or episodic content. This study aimed to (1) review the existing literature to formally characterize the variability in analysis of 'non-episodic' content (i.e., external details) on the Autobiographical Interview and (2) use these findings to create a theoretically grounded framework for coding external details. Our review exposed discrepancies in the reporting and interpretation of external details across studies, reinforcing the need for a new, consistent approach. We validated our new external details scoring protocol (the 'NExt' taxonomy) in patients with Alzheimer's disease (n = 18) and semantic dementia (n = 13), and 20 healthy older Control participants and compared profiles of the NExt subcategories across groups and time periods. Our results revealed increased sensitivity of the NExt taxonomy in discriminating between ABM profiles of patient groups, when compared to traditionally used internal and external detail metrics. Further, remote and recent autobiographical memories displayed distinct compositions of the NExt detail types. This study is the first to provide a fine-grained and comprehensive taxonomy to parse external details into intuitive subcategories and to validate this protocol in neurodegenerative disorders. © 2018 The British Psychological Society.

Survey of solar thermal test facilities

Energy Technology Data Exchange (ETDEWEB)

Masterson, K.

1979-08-01

The facilities that are presently available for testing solar thermal energy collection and conversion systems are briefly described. Facilities that are known to meet ASHRAE standard 93-77 for testing flat-plate collectors are listed. The DOE programs and test needs for distributed concentrating collectors are identified. Existing and planned facilities that meet these needs are described and continued support for most of them is recommended. The needs and facilities that are suitable for testing components of central receiver systems, several of which are located overseas, are identified. The central contact point for obtaining additional details and test procedures for these facilities is the Solar Thermal Test Facilities Users' Association in Albuquerque, N.M. The appendices contain data sheets and tables which give additional details on the technical capabilities of each facility. Also included is the 1975 Aerospace Corporation report on test facilities that is frequently referenced in the present work.

Theory Testing Using Case Studies

DEFF Research Database (Denmark)

Sørensen, Pernille Dissing; Løkke, Ann-Kristina

2006-01-01

design. Finally, we discuss the epistemological logic, i.e., the value to larger research programmes, of such studies and, following Lakatos, conclude that the value of theory-testing case studies lies beyond naïve falsification and in their contribution to developing research programmes in a progressive...

Combustion Safety Simplified Test Protocol Field Study

Energy Technology Data Exchange (ETDEWEB)

Brand, L [Gas Technology Inst., Des Plaines, IL (United States); Cautley, D. [Gas Technology Inst., Des Plaines, IL (United States); Bohac, D. [Gas Technology Inst., Des Plaines, IL (United States); Francisco, P. [Gas Technology Inst., Des Plaines, IL (United States); Shen, L. [Gas Technology Inst., Des Plaines, IL (United States); Gloss, S. [Gas Technology Inst., Des Plaines, IL (United States)

2015-11-05

"9Combustions safety is an important step in the process of upgrading homes for energy efficiency. There are several approaches used by field practitioners, but researchers have indicated that the test procedures in use are complex to implement and provide too many false positives. Field failures often mean that the house is not upgraded until after remediation or not at all, if not include in the program. In this report the PARR and NorthernSTAR DOE Building America Teams provide a simplified test procedure that is easier to implement and should produce fewer false positives. A survey of state weatherization agencies on combustion safety issues, details of a field data collection instrumentation package, summary of data collected over seven months, data analysis and results are included. The project provides several key results. State weatherization agencies do not generally track combustion safety failures, the data from those that do suggest that there is little actual evidence that combustion safety failures due to spillage from non-dryer exhaust are common and that only a very small number of homes are subject to the failures. The project team collected field data on 11 houses in 2015. Of these homes, two houses that demonstrated prolonged and excessive spillage were also the only two with venting systems out of compliance with the National Fuel Gas Code. The remaining homes experienced spillage that only occasionally extended beyond the first minute of operation. Combustion zone depressurization, outdoor temperature, and operation of individual fans all provide statistically significant predictors of spillage.

Reliability test for reactor internals rejuvenation technology

International Nuclear Information System (INIS)

Uchiyama, Junichi

1998-01-01

41 transparencies were presented on the subject of 'Reliability test for reactor internals rejuvenation technology'. The items presented give an introduction on the management of plant life in Japan and introduce the Nuclear Power Engineering Corporation (NUPEC). The question of what reliability tests for rejuvenation of reactor internals are is discussed in some detail and an outline of each test is given. Altogether six methods to rejuvenate reactor internals are presented, two of which have already been applied to actual plants. The presentation was supported by many detailed drawings and images

NONLINEAR FINITE ELEMENT ANALYSIS OF NONSEISMICALLY DETAILED INTERIOR RC BEAM-COLUMN CONNECTION UNDER REVERSED CYCLIC LOAD

Directory of Open Access Journals (Sweden)

Teeraphot Supaviriyakit

2017-11-01

Full Text Available This paper presents a nonlinear finite element analysis of non-seismically detailed RC beam column connections under reversed cyclic load. The test of half-scale nonductile reinforced concrete beam-column joints was conducted. The tested specimens represented those of the actual mid-rise reinforced concrete frame buildings designed according to the non-seismic provisions of the ACI building code.  The test results show that specimens representing small and medium column tributary area failed in brittle joint shear while specimen representing large column tributary area failed by ductile flexure though no ductile reinforcement details were provided. The nonlinear finite element analysis was applied to simulate the behavior of the specimens. The finite element analysis employs the smeared crack approach for modeling beam, column and joint, and employs the discrete crack approach for modeling the interface between beam and joint face. The nonlinear constitutive models of reinforced concrete elements consist of coupled tension-compression model to model normal force orthogonal and parallel to the crack and shear transfer model to capture the shear sliding mechanism. The FEM shows good comparison with test results in terms of load-displacement relations, hysteretic loops, cracking process and the failure mode of the tested specimens. The finite element analysis clarifies that the joint shear failure was caused by the collapse of principal diagonal concrete strut.

Adaptive linear rank tests for eQTL studies.

Science.gov (United States)

Szymczak, Silke; Scheinhardt, Markus O; Zeller, Tanja; Wild, Philipp S; Blankenberg, Stefan; Ziegler, Andreas

2013-02-10

Expression quantitative trait loci (eQTL) studies are performed to identify single-nucleotide polymorphisms that modify average expression values of genes, proteins, or metabolites, depending on the genotype. As expression values are often not normally distributed, statistical methods for eQTL studies should be valid and powerful in these situations. Adaptive tests are promising alternatives to standard approaches, such as the analysis of variance or the Kruskal-Wallis test. In a two-stage procedure, skewness and tail length of the distributions are estimated and used to select one of several linear rank tests. In this study, we compare two adaptive tests that were proposed in the literature using extensive Monte Carlo simulations of a wide range of different symmetric and skewed distributions. We derive a new adaptive test that combines the advantages of both literature-based approaches. The new test does not require the user to specify a distribution. It is slightly less powerful than the locally most powerful rank test for the correct distribution and at least as powerful as the maximin efficiency robust rank test. We illustrate the application of all tests using two examples from different eQTL studies. Copyright © 2012 John Wiley & Sons, Ltd.

The test facility for the short prototypes of the LHC superconducting magnets

International Nuclear Information System (INIS)

Delsolaro, W. Venturini; Arn, A.; Bottura, L.; Giloux, C.; Mompo, R.; Siemko, A.; Walckiers, L.

2002-01-01

The LHC development program relies on cryogenic tests of prototype and model magnets. This vigorous program is pursued in a dedicated test facility based on several vertical cryostats working at superfluid helium temperatures. The performance of the facility is detailed. Goals and test equipment for currently performed studies are reviewed: quench analysis and magnet protection studies, measurement of the field quality, test of ancillary electrical equipment like diodes and busbars. The paper covers the equipment available for tests of prototypes and some special series of LHC magnets to come

The test facility for the short prototypes of the LHC superconducting magnets

Science.gov (United States)

Delsolaro, W. Venturini; Arn, A.; Bottura, L.; Giloux, C.; Mompo, R.; Siemko, A.; Walckiers, L.

2002-05-01

The LHC development program relies on cryogenic tests of prototype and model magnets. This vigorous program is pursued in a dedicated test facility based on several vertical cryostats working at superfluid helium temperatures. The performance of the facility is detailed. Goals and test equipment for currently performed studies are reviewed: quench analysis and magnet protection studies, measurement of the field quality, test of ancillary electrical equipment like diodes and busbars. The paper covers the equipment available for tests of prototypes and some special series of LHC magnets to come.

The Soleil detailed pre-project report

International Nuclear Information System (INIS)

1999-01-01

The aim of the joint CNRS/CEA Soleil project was to develop a facility equipped with several synchrotron radiation sources and their associated experimental devices in order to answer the estimated research needs in this domain for the 20 to 30 forthcoming years. This document is the detailed pre-project. It describes the studies carried out and relative to the infrastructures and buildings, to the accelerators and light sources (storage ring, injector, radiation production), to the program of experiments, to the computer science aspects, and to the administrative and organisational aspects. (J.S.)

Association Between Academic Medical Center Pharmaceutical Detailing Policies and Physician Prescribing.

Science.gov (United States)

Larkin, Ian; Ang, Desmond; Steinhart, Jonathan; Chao, Matthew; Patterson, Mark; Sah, Sunita; Wu, Tina; Schoenbaum, Michael; Hutchins, David; Brennan, Troyen; Loewenstein, George

2017-05-02

In an effort to regulate physician conflicts of interest, some US academic medical centers (AMCs) enacted policies restricting pharmaceutical representative sales visits to physicians (known as detailing) between 2006 and 2012. Little is known about the effect of these policies on physician prescribing. To analyze the association between detailing policies enacted at AMCs and physician prescribing of actively detailed and not detailed drugs. The study used a difference-in-differences multivariable regression analysis to compare changes in prescribing by physicians before and after implementation of detailing policies at AMCs in 5 states (California, Illinois, Massachusetts, Pennsylvania, and New York) that made up the intervention group with changes in prescribing by a matched control group of similar physicians not subject to a detailing policy. Academic medical center implementation of policies regulating pharmaceutical salesperson visits to attending physicians. The monthly within-drug class market share of prescriptions written by an individual physician for detailed and nondetailed drugs in 8 drug classes (lipid-lowering drugs, gastroesophageal reflux disease drugs, diabetes drugs, antihypertensive drugs, hypnotic drugs approved for the treatment of insomnia [sleep aids], attention-deficit/hyperactivity disorder drugs, antidepressant drugs, and antipsychotic drugs) comparing the 10- to 36-month period before implementation of the detailing policies with the 12- to 36-month period after implementation, depending on data availability. The analysis included 16 121 483 prescriptions written between January 2006 and June 2012 by 2126 attending physicians at the 19 intervention group AMCs and by 24 593 matched control group physicians. The sample mean market share at the physician-drug-month level for detailed and nondetailed drugs prior to enactment of policies was 19.3% and 14.2%, respectively. Exposure to an AMC detailing policy was associated with a

Space Station Freedom environmental control and life support system phase 3 simplified integrated test detailed report

Science.gov (United States)

Roberts, B. C.; Carrasquillo, R. L.; Dubiel, M. Y.; Ogle, K. Y.; Perry, J. L.; Whitley, K. M.

1990-01-01

A description of the phase 3 simplified integrated test (SIT) conducted at the Marshall Space Flight Center (MSFC) Core Module Integration Facility (CMIF) in 1989 is presented. This was the first test in the phase 3 series integrated environmental control and life support systems (ECLSS) tests. The basic goal of the SIT was to achieve full integration of the baseline air revitalization (AR) subsystems for Space Station Freedom. Included is a description of the SIT configuration, a performance analysis of each subsystem, results from air and water sampling, and a discussion of lessons learned from the test. Also included is a full description of the preprototype ECLSS hardware used in the test.

Cyclic Testing of Steel Chevron Braces with Vertically Slotted Beam Connection

Directory of Open Access Journals (Sweden)

Rozlyn K. Bubela

2010-07-01

Full Text Available Experimental tests were performed to study the seismic behavior and performance of modified steel chevron braced frame systems, which incorporate a vertical slotted connection (VSC detail between the top of the braces and the floor beam above. The VSC detail is intended to prevent vertical load transfer to the beam and limit brace forces to the compressive resistance of the members. Full-scale quasi-static cyclic tests were performed on two specimens with hollow tube braces, with one specimen having the braces filled with concrete. Both frames exhibited stable, predictable behavior under cyclic loading. The VSC detail provided free vertical movement of the brace assembly during both tests. However, its flexibility created a moderate reduction in the overall lateral stiffness of the frame. The concrete-filled tube specimen sustained higher peak loads, demonstrated greater residual strength and dissipated more energy than the hollow tube specimen due to the partial inhibition of local buckling by the concrete core. It was found that the VSC chevron braced frame system is a suitable concept for use in buildings in high-risk seismic zones.

Kinetic energy budget details

Indian Academy of Sciences (India)

Abstract. This paper presents the detailed turbulent kinetic energy budget and higher order statistics of flow behind a surface-mounted rib with and without superimposed acoustic excitation. Pattern recognition technique is used to determine the large-scale structure magnitude. It is observed that most of the turbulence ...

Surface Detail Reproduction and Effect of Disinfectant and Long-Term Storage on the Dimensional Stability of a Novel Vinyl Polyether Silicone Impression Material.

Science.gov (United States)

Nassar, Usama; Chow, Ava K

2015-08-01

This study investigated the surface detail reproduction and dimensional stability of a vinyl polyether silicone (VPES) in comparison to a vinylpolysiloxane (VPS) material as a function of prolonged storage for up to 2 weeks. Heavy-body VPES (EXA'lence(TM) Fast Set) and VPS (Imprint(TM) 3 Quick Step) were compared. Forty impression ingots of each material were made using a stainless steel die as described by ANSI/ADA specification No. 19. Twenty impressions of each material were disinfected by immersion in a 2.5% buffered glutaraldehyde solution. Surface quality was assessed and scored immediately after making the ingots. Dimensional stability measurements were made immediately and repeated on the same ingots after 7 and 14 days storage in ambient laboratory conditions. Data were analyzed using the D'Agostino and Pearson omnibus normality test followed by two-way repeated measures ANOVA with post hoc Bonferroni tests. Values of p < 0.01 were deemed to be significant. Disinfected VPES and VPS specimens had significantly reduced dimensional changes at 7 and 14 days when compared with the nondisinfected ones (p < 0.0001). The dimensional stability of both materials was within ANSI/ADA specification No. 19's acceptable limit throughout the 2-week test period, regardless of whether they were disinfected. Out of the initial 80 ingots, 8 VPES and 1 VPS ingot scored a 2 on the surface detail test, while the remaining 71 ingots scored 1. Heavy-body fast-set VPES experienced minimal contraction in vitro after prolonged storage, though surface detail scores were not as consistent as those of the VPS tested. The least contraction occurred when the material was examined immediately after ingot production. © 2014 by the American College of Prosthodontists.

Leachates draining from controlled municipal solid waste landfill: Detailed geochemical characterization and toxicity tests.

Science.gov (United States)

Mavakala, Bienvenu K; Le Faucheur, Séverine; Mulaji, Crispin K; Laffite, Amandine; Devarajan, Naresh; Biey, Emmanuel M; Giuliani, Gregory; Otamonga, Jean-Paul; Kabatusuila, Prosper; Mpiana, Pius T; Poté, John

2016-09-01

Management of municipal solid wastes in many countries consists of waste disposal into landfill without treatment or selective collection of solid waste fractions including plastics, paper, glass, metals, electronic waste, and organic fraction leading to the unsolved problem of contamination of numerous ecosystems such as air, soil, surface, and ground water. Knowledge of leachate composition is critical in risk assessment of long-term impact of landfills on human health and the environment as well as for prevention of negative outcomes. The research presented in this paper investigates the seasonal variation of draining leachate composition and resulting toxicity as well as the contamination status of soil/sediment from lagoon basins receiving leachates from landfill in Mpasa, a suburb of Kinshasa in the Democratic Republic of the Congo. Samples were collected during the dry and rainy seasons and analyzed for pH, electrical conductivity, dissolved oxygen, soluble ions, toxic metals, and were then subjected to toxicity tests. Results highlight the significant seasonal difference in leachate physicochemical composition. Affected soil/sediment showed higher values for toxic metals than leachates, indicating the possibility of using lagoon system for the purification of landfill leachates, especially for organic matter and heavy metal sedimentation. However, the ecotoxicity tests demonstrated that leachates are still a significant source of toxicity for terrestrial and benthic organisms. Therefore, landfill leachates should not be discarded into the environment (soil or surface water) without prior treatment. Interest in the use of macrophytes in lagoon system is growing and toxic metal retention in lagoon basin receiving systems needs to be fully investigated in the future. This study presents useful tools for evaluating landfill leachate quality and risk in lagoon systems which can be applied to similar environmental compartments. Copyright © 2016 Elsevier Ltd. All

The case of the missing visual details: Occlusion and long-term visual memory.

Science.gov (United States)

Williams, Carrick C; Burkle, Kyle A

2017-10-01

To investigate the critical information in long-term visual memory representations of objects, we used occlusion to emphasize 1 type of information or another. By occluding 1 solid side of the object (e.g., top 50%) or by occluding 50% of the object with stripes (like a picket fence), we emphasized visible information about the object, processing the visible details in the former and the object's overall form in the latter. On a token discrimination test, surprisingly, memory for solid or stripe occluded objects at either encoding (Experiment 1) or test (Experiment 2) was the same. In contrast, when occluded objects matched at encoding and test (Experiment 3) or when the occlusion shifted, revealing the entire object piecemeal (Experiment 4), memory was better for solid compared with stripe occluded objects, indicating that objects are represented differently in long-term visual memory. Critically, we also found that when the task emphasized remembering exactly what was shown, memory performance in the more detailed solid occlusion condition exceeded that in the stripe condition (Experiment 5). However, when the task emphasized the whole object form, memory was better in the stripe condition (Experiment 6) than in the solid condition. We argue that long-term visual memory can represent objects flexibly, and task demands can interact with visual information, allowing the viewer to cope with changing real-world visual environments. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

Repetitive Rockfall Trajectory Testing

Directory of Open Access Journals (Sweden)

Axel Volkwein

2018-03-01

Full Text Available Numerical simulations of rockfall trajectories are a standard procedure for evaluating rockfall hazards. For these simulations, corresponding software codes must be calibrated and evaluated based on field data. This study addresses methods of repeatable rockfall tests, and investigates whether it is possible to produce traceable and statistically analysable data. A testing series is described extensively covering how to conduct rockfall experiments and how certain elements of rockfall trajectories can be measured. The tests use acceleration and rotation sensors inside test blocks, a system to determine block positions over time, surveying measurements, and video recordings. All systems are evaluated regarding their usability in the field and for analyses. The highly detailed description of testing methods is the basis for sound understanding and reproducibility of the tests. This article serves as a reference for future publications and other rockfall field tests, both as a guide and as a basis for comparisons. First analyses deliver information on runout with a shadow angle ranging between 21 and 45 degrees for a slope consisting of homogeneous soft soil. A digital elevation model of the test site as well as point clouds of the used test blocks are part of this publication.

100 statistical tests

CERN Document Server

Kanji, Gopal K

2006-01-01

This expanded and updated Third Edition of Gopal K. Kanji's best-selling resource on statistical tests covers all the most commonly used tests with information on how to calculate and interpret results with simple datasets. Each entry begins with a short summary statement about the test's purpose, and contains details of the test objective, the limitations (or assumptions) involved, a brief outline of the method, a worked example, and the numerical calculation. 100 Statistical Tests, Third Edition is the one indispensable guide for users of statistical materials and consumers of statistical information at all levels and across all disciplines.

L-286, Acceptance Test Record

International Nuclear Information System (INIS)

HARMON, B.C.

2000-01-01

This document provides a detailed account of how the acceptance testing was conducted for Project L-286, ''200E Area Sanitary Water Plant Effluent Stream Reduction''. The testing of the L-286 instrumentation system was conducted under the direct supervision

Visualisation of details of a complicated inner structure of model objects by the method of diffusion optical tomography

International Nuclear Information System (INIS)

Tret'yakov, Evgeniy V; Shuvalov, Vladimir V; Shutov, I V

2002-01-01

An approximate algorithm is tested for solving the problem of diffusion optical tomography in experiments on the visualisation of details of the inner structure of strongly scattering model objects containing scattering and semitransparent inclusions, as well as absorbing inclusions located inside other optical inhomogeneities. The stability of the algorithm to errors is demonstrated, which allows its use for a rapid (2 - 3 min) image reconstruction of the details of objects with a complicated inner structure. (laser biology and medicine)

Development of Phenomenological Models of Underground Nuclear Tests on Pahute Mesa, Nevada Test Site - BENHAM and TYBO

Energy Technology Data Exchange (ETDEWEB)

Pawloski, G.A.

1999-09-21

Although it is well accepted that underground nuclear explosions modify the in situ geologic media around the explosion point, the details of these changes are neither well understood nor well documented. As part of the engineering and containment process before a nuclear test, the physical environment is characterized to some extent to predict how the explosion will interact with the in situ media. However, a more detailed characterization of the physical environment surrounding an expended site is needed to successfully model radionuclide transport in the groundwater away from the detonation point. It is important to understand how the media have been altered and where the radionuclides are deposited. Once understood, this information on modified geologic media can be incorporated into a phenomenological model that is suitable for input to computer simulations of groundwater flow and radionuclide transport. The primary goals of this study are to (1) identify the modification of the media at a pertinent scale, and (2) provide this information to researchers modeling radionuclide transport in groundwater for the US Department of Energy (DOE) Nevada Operations Office Underground Test Area (UGTA) Project. Results from this study are most applicable at near-field scale (a model domain of about 500 m) and intermediate-field scale (a model domain of about 5 km) for which detailed information can be maximized as it is incorporated in the modeling grids. UGTA collected data on radionuclides in groundwater during recent drilling at the ER-20-5 site, which is near BENHAM and TYBO on Pahute Mesa at the Nevada Test Site (NTS). Computer simulations are being performed to better understand radionuclide transport. The objectives of this modeling effort include: evaluating site-specific information from the BENHAM and TYBO tests on Pahute Mesa; augmenting the above data set with generalized containment data; and developing a phenomenological model suitable for input to

Clock Drawing Test and the diagnosis of amnestic mild cognitive impairment: can more detailed scoring systems do the work?

Science.gov (United States)

Rubínová, Eva; Nikolai, Tomáš; Marková, Hana; Siffelová, Kamila; Laczó, Jan; Hort, Jakub; Vyhnálek, Martin

2014-01-01

The Clock Drawing Test is a frequently used cognitive screening test with several scoring systems in elderly populations. We compare simple and complex scoring systems and evaluate the usefulness of the combination of the Clock Drawing Test with the Mini-Mental State Examination to detect patients with mild cognitive impairment. Patients with amnestic mild cognitive impairment (n = 48) and age- and education-matched controls (n = 48) underwent neuropsychological examinations, including the Clock Drawing Test and the Mini-Mental State Examination. Clock drawings were scored by three blinded raters using one simple (6-point scale) and two complex (17- and 18-point scales) systems. The sensitivity and specificity of these scoring systems used alone and in combination with the Mini-Mental State Examination were determined. Complex scoring systems, but not the simple scoring system, were significant predictors of the amnestic mild cognitive impairment diagnosis in logistic regression analysis. At equal levels of sensitivity (87.5%), the Mini-Mental State Examination showed higher specificity (31.3%, compared with 12.5% for the 17-point Clock Drawing Test scoring scale). The combination of Clock Drawing Test and Mini-Mental State Examination scores increased the area under the curve (0.72; p Drawing Test did not differentiate between healthy elderly and patients with amnestic mild cognitive impairment in our sample. Complex scoring systems were slightly more efficient, yet still were characterized by high rates of false-positive results. We found psychometric improvement using combined scores from the Mini-Mental State Examination and the Clock Drawing Test when complex scoring systems were used. The results of this study support the benefit of using combined scores from simple methods.

MRI studies of the hydrodynamics in a USP 4 dissolution testing cell.

Science.gov (United States)

Shiko, G; Gladden, L F; Sederman, A J; Connolly, P C; Butler, J M

2011-03-01

We present a detailed study of hydrodynamics inside the flow-through dissolution apparatus when operated according to USP recommendations. The pulsatile flow inside the flow-through cell was measured quantitatively using magnetic resonance imaging (MRI) at a spatial resolution of 234 × 234 μm(2) and slice thickness of 1 mm. We report the experimental protocols developed for in situ MRI studies and the effect that the operating conditions and tablet orientation have on the hydrodynamics inside commercial flow cells. It was found that the flow field inside the dissolution cells was, at most operating conditions, heterogeneous, rather than fully developed laminar flow, and characterised by re-circulation and backward flow. A model tablet was shown to be contacted by a wide distribution of local velocities as a function of position and orientation in the flow cell. The use of 1 mm beads acted as a distributor of the flow but did not suffice to ensure a fully developed laminar flow profile. These results emphasise the necessity to understand the influence of test conditions on dissolution behaviour in defining robust flow-through dissolution methods. Copyright © 2010 Wiley-Liss, Inc.

Detailed mechanical design and manufacturing study for the ITER reference breeding blanket

International Nuclear Information System (INIS)

Zacchia, F.; Daenner, W.; Stefanis, L. de; Ferrari, M.; Gerber, A.; Mustoe, J.

1998-01-01

This papers relates on the detailed mechanical design, manufacturing feasibility and assembly analysis of a water-cooled solid breeding blanket concept, selected as the ITER reference design. This breeding blanket design is characterised by: i) pressurised water flowing inside flat steel panels for cooling of the internals; each panel is welded along its contour onto the first wall structure and to the rear shield plate after closure of the module (last assembly step). ii) Beryllium (neutronic multiplier) in the form of micro-spheres filling the volume between parallel flat coolant panels. iii) Breeder pebbles enclosed in rods, which form bundles and are themselves embedded inside the Beryllium micro-spheres. (authors)

Verifying detailed fluctuation relations for discrete feedback-controlled quantum dynamics

Science.gov (United States)

Camati, Patrice A.; Serra, Roberto M.

2018-04-01

Discrete quantum feedback control consists of a managed dynamics according to the information acquired by a previous measurement. Energy fluctuations along such dynamics satisfy generalized fluctuation relations, which are useful tools to study the thermodynamics of systems far away from equilibrium. Due to the practical challenge to assess energy fluctuations in the quantum scenario, the experimental verification of detailed fluctuation relations in the presence of feedback control remains elusive. We present a feasible method to experimentally verify detailed fluctuation relations for discrete feedback control quantum dynamics. Two detailed fluctuation relations are developed and employed. The method is based on a quantum interferometric strategy that allows the verification of fluctuation relations in the presence of feedback control. An analytical example to illustrate the applicability of the method is discussed. The comprehensive technique introduced here can be experimentally implemented at a microscale with the current technology in a variety of experimental platforms.

GALEN skin test study III: Minimum battery of test inhalent allergens needed in epidemiological studies in patients

NARCIS (Netherlands)

Bousquet, P.-J.; Burbach, G.; Heinzerling, L. M.; Edenharter, G.; Bachert, C.; Bindslev-Jensen, C.; Bonini, S.; Bousquet-Rouanet, L.; Demoly, P.; Bresciani, M.; Bruno, A.; Gjomarkaj, M.; Canonica, G. W.; Darsow, U.; Durham, S.; Fokkens, W. J.; Giavi, S.; Gramiccioni, C.; Papadopoulos, N. G.; Haahtela, T.; Kowalski, M. L.; Magyar, P.; Muraközi, G.; Orosz, M.; Röhnelt, C.; Stingl, G.; Todo-Bom, A.; von Mutius, E.; Wiesner, A.; Wöhrl, S.; Bousquet, J.; Zuberbier, T.

2009-01-01

Background: The number of allergens to be tested in order to identify sensitized patients is important in order to have the most cost-effective approach in epidemiological studies. Objective: To define the minimal number and the type of skin prick test (SPT) allergens required to identify a patient

Three Latin Phonological Details

DEFF Research Database (Denmark)

Olsen, Birgit Anette

2006-01-01

The present paper deals with three minor details of Latin phonology: 1) the development of the initial sequence *u¿l¿-, where it is suggested that an apparent vacillation between ul- and vol-/vul- represents sandhi variants going back to the proto-language, 2) the adjectives ama¯rus ‘bitter' and ...

Memory for details with self-referencing.

Science.gov (United States)

Serbun, Sarah J; Shih, Joanne Y; Gutchess, Angela H

2011-11-01

Self-referencing benefits item memory, but little is known about the ways in which referencing the self affects memory for details. Experiment 1 assessed whether the effects of self-referencing operate only at the item, or general, level or whether they also enhance memory for specific visual details of objects. Participants incidentally encoded objects by making judgements in reference to the self, a close other (one's mother), or a familiar other (Bill Clinton). Results indicate that referencing the self or a close other enhances both specific and general memory. Experiments 2 and 3 assessed verbal memory for source in a task that relied on distinguishing between different mental operations (internal sources). The results indicate that self-referencing disproportionately enhances source memory, relative to conditions referencing other people, semantic, or perceptual information. We conclude that self-referencing not only enhances specific memory for both visual and verbal information, but can also disproportionately improve memory for specific internal source details.

Phase Startup Initiative Phases 3 and 4 Test Plan and Test Specification ( OCRWM)

Energy Technology Data Exchange (ETDEWEB)

PAJUNEN, A.L.; LANGEVIN, M.J.

2000-08-07

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: Define the Phase 3 and 4 test scope for the FRS and IWTS; Provide detailed test requirements that can be used to write the specific test procedures; Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and Define specific test objectives and acceptance criteria.

Phase Startup Initiative Phases 3 and 4 Test Plan and Test Specification (OCRWM)

International Nuclear Information System (INIS)

PAJUNEN, A.L.; LANGEVIN, M.J.

2000-01-01

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: Define the Phase 3 and 4 test scope for the FRS and IWTS; Provide detailed test requirements that can be used to write the specific test procedures; Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and Define specific test objectives and acceptance criteria

Concrete decontamination scoping tests

International Nuclear Information System (INIS)

Archibald, K.E.

1995-01-01

This report details the research efforts and scoping tests performed at the Idaho Chemical Process Plant using scabbling, chemical, and electro-osmotic decontamination techniques on radiologically contaminated concrete

Verification test for three WindCube WLS7 LiDARs at the Høvsøre test site

DEFF Research Database (Denmark)

Gottschall, Julia; Courtney, Michael

The report describes the procedure of testing ground-based WindCube lidars (manufactured by the French company Leosphere) at the Høvsøre test site in comparison to reference sensors mounted at a meteorological mast. Results are presented for three tested units – in detail for unit WLS7-0062, and ......-0062, and in a summary for units WLS7-0064 and WLS7-0066. The verification test covers the evaluation of measured mean wind speeds, wind directions and wind speed standard deviations. The data analysis is basically performed in terms of different kinds of regression analyses.......The report describes the procedure of testing ground-based WindCube lidars (manufactured by the French company Leosphere) at the Høvsøre test site in comparison to reference sensors mounted at a meteorological mast. Results are presented for three tested units – in detail for unit WLS7...

Data qualification summary for 1985 L-Area AC Flow Tests

International Nuclear Information System (INIS)

Edwards, T.B.; Eghbali, D.A.; Liebmann, M.L.; Shine, E.P.

1992-03-01

The 1985 L-Area AC Flow Tests were conducted to provide an extended data base for upgrading the reactor system models employed in predicting normal process water flows. This report summarizes the results of the recently completed, formal, technical review of the data from the 1985 L-Area AC Flow Tests as detailed in document SCS-CMAS-910045. The purpose of that review was to provide corroborating technical information as to the quality (fitness for use) of these experimental data. Reference [1] required three volumes to fully document the results of that Data Qualification process. This report has been prepared to provide the important conclusions from that process in a manageable and understandable format. Consult reference [1] if any additional information or detail is needed. This report provides highlights from that study: an overview of the tests and data, a description of the instrumentation used, an explanation of the data qualification methods employed to review the data, and the important conclusions reached from the study. Reference 1: Edwards, T.B., D.A. Eghbali, M.L. Liebmann, and E.P. Shine, open-quotes Data Qualification for 1985 L-Area AC Flow Tests,close quotes SCS-CMAS-910045, December 31, 1991

Expanding the Availability of Lightweight Aluminum Alloy Armor Plate Procured from Detailed Military Specifications

Science.gov (United States)

Doherty, Kevin; Squillacioti, Richard; Cheeseman, Bryan; Placzankis, Brian; Gallardy, Denver

For many years, the range of aluminum alloys for armor plate applications obtainable in accordance with detailed military specifications was very limited. However, the development of improved aluminum alloys for aerospace and other applications has provided an opportunity to modernize the Army portfolio for ground vehicle armor applications. While the benefits of offering additional alloy choices to vehicle designers is obvious, the process of creating detailed military specifications for armor plate applications is not trivial. A significant amount of material and testing is required to develop the details required by an armor plate specification. Due to the vast number of material programs that require standardization and with a limited amount of manpower and funds as a result of Standardization Reform in 1995, one typically requires a need statement from a vehicle program office to justify and sponsor the work. This presentation will focus on recent aluminum alloy armor plate specifications that have added capability to vehicle designers' selection of armor materials that offer possible benefits such as lower cost, higher strength, better ballistic and corrosion resistance, improved weldability, etc.

Test Plan: Phase 1, Hanford LLW melter tests, GTS Duratek, Inc

International Nuclear Information System (INIS)

Eaton, W.C.

1995-01-01

This document provides a test plan for the conduct of vitrification testing by a vendor in support of the Hanford Tank Waste Remediation System (TWRS) Low-Level Waste (LLW) Vitrification Program. The vendor providing this test plan and conducting the work detailed within it [one of seven selected for glass melter testing under Purchase Order MMI-SVV-384215] is GTS Duratek, Inc., Columbia, Maryland. The GTS Duratek project manager for this work is J. Ruller. This test plan is for Phase I activities described in the above Purchase Order. Test conduct includes melting of glass with Hanford LLW Double-Shell Slurry Feed waste simulant in a DuraMelter trademark vitrification system

BWR Full Integral Simulation Test (FIST). Phase I test results

International Nuclear Information System (INIS)

Hwang, W.S.; Alamgir, M.; Sutherland, W.A.

1984-09-01

A new full height BWR system simulator has been built under the Full-Integral-Simulation-Test (FIST) program to investigate the system responses to various transients. The test program consists of two test phases. This report provides a summary, discussions, highlights and conclusions of the FIST Phase I tests. Eight matrix tests were conducted in the FIST Phase I. These tests have investigated the large break, small break and steamline break LOCA's, as well as natural circulation and power transients. Results and governing phenomena of each test have been evaluated and discussed in detail in this report. One of the FIST program objectives is to assess the TRAC code by comparisons with test data. Two pretest predictions made with TRACB02 are presented and compared with test data in this report

Generalized detailed balance theory of solar cells

Energy Technology Data Exchange (ETDEWEB)

Kirchartz, Thomas

2009-12-12

The principle of detailed balance is the requirement that every microscopic process in a system must be in equilibrium with its inverse process, when the system itself is in thermodynamic equilibrium. This detailed balance principle has been of special importance for photovoltaics, since it allows the calculation of the limiting efficiency of a given solar cell by defining the only fundamental loss process as the radiative recombination of electron/hole pairs followed by the emission of a photon. In equilibrium, i.e. in the dark and without applied voltage, the absorbed and emitted photon flux must be equal due to detailed balance. This equality determines the radiative recombination from absorption and vice versa. While the classical theory of photovoltaic efficiency limits by Shockley and Queisser considers only one detailed balance pair, namely photogeneration and radiative recombination, the present work extends the detailed balance principle to any given process in the solar cell. Applying the detailed balance principle to the whole device leads to two major results, namely (i) a model that is compatible with the Shockley-Queisser efficiency limit for efficient particle transport, while still being able to describe non-ideal and non-linear solar cells, and (ii) an analytical relation between electroluminescent emission and photovoltaic action of a diode that is applied to a variety of different solar cells. This thesis presents several variations of a detailed balance model that are applicable to different types of solar cells. Any typical inorganic solar cell is a mainly bipolar device, meaning that the current is carried by electrons and holes. The detailed balance model for pn-type and pin-type bipolar solar cells is therefore the most basic incorporation of a detailed balance model. The only addition compared to the classical diode theory or compared to standard one-dimensional device simulators is the incorporation of photon recycling, making the model

Local address and emergency contact details

CERN Multimedia

2013-01-01

The HR Department would like to remind members of the personnel that they are responsible for ensuring that their personal data concerning local address and preferred emergency contact details remains valid and up-to-date.   Both are easily accessible via the links below: Local address: https://edh.cern.ch/Document/Personnel/LocalAddressChange   Emergency contacts: https://edh.cern.ch/Document/Personnel/EC   Please take a few minutes to check your details and modify if necessary. Thank you in advance. HR Department Head Office

Methodological Details and Full Bibliography

Data.gov (United States)

U.S. Environmental Protection Agency — This dataset has several components, The first part describes fully our literature review, providing details not included in the text. The second part provides all...

Test Design Project: Studies in Test Adequacy. Annual Report.

Science.gov (United States)

Wilcox, Rand R.

These studies in test adequacy focus on two problems: procedures for estimating reliability, and techniques for identifying ineffective distractors. Fourteen papers are presented on recent advances in measuring achievement (a response to Molenaar); "an extension of the Dirichlet-multinomial model that allows true score and guessing to be…

Test results of Nb3Sn ribbons for the Princeton D coil test program

International Nuclear Information System (INIS)

Kaugerts, J.; File, J.; Willard, J.W.

1974-10-01

A previously described D coil test program was modified. Details of a smaller Nb 3 Sn D coil test program are described. Cusp coil tests were made with several Nb 3 Sn composite ribbons. Measurements of both the quench and recovery currents as a function of magnetic field component perpendicular to the wide edge of the ribbon are presented. (auth)

Detailed technical plan for Test Program Element-III (TPE-III) of the first wall/blanket shield engineering test program

Energy Technology Data Exchange (ETDEWEB)

Turner, L.R.; Praeg, W.F.

1982-03-01

The experimental requirements, test-bed design, and computational requirements are reviewed and updated. Next, in Sections 3, 4 and 5, the experimental plan, instrumentation, and computer plan, respectively, are described. Finally, Section 6 treats other considerations, such as personnel, outside participation, and distribution of results.

Detailed technical plan for Test Program Element-III (TPE-III) of the first wall/blanket shield engineering test program

International Nuclear Information System (INIS)

Turner, L.R.; Praeg, W.F.

1982-03-01

The experimental requirements, test-bed design, and computational requirements are reviewed and updated. Next, in Sections 3, 4 and 5, the experimental plan, instrumentation, and computer plan, respectively, are described. Finally, Section 6 treats other considerations, such as personnel, outside participation, and distribution of results

Detailed study of transmutation scenarios involving present day reactor technologies

International Nuclear Information System (INIS)

2003-01-01

This document makes a detailed technical evaluation of three families of separation-transmutation scenarios for the management of radioactive wastes. These scenarios are based on 2 parks of reactors which recycle plutonium and minor actinides in an homogeneous way. A first scenario considers the multi-recycling of Pu and Np and the mono-recycling of Am and Cm using both PWRs and FBRs. A second scenario is based on PWRs only, while a third one considers FBRs only. The mixed PWR+FBR scenario requires innovative options and gathers more technical difficulties due to the americium and curium management in a minimum flux of materials. A particular attention has been given to the different steps of the fuel cycle (fuels and targets fabrication, burnup, spent fuel processing, targets management). The feasibility of scenarios of homogeneous actinides recycling in PWRs-only and in FBRs-only has been evaluated according to the results of the first scenario: fluxes of materials, spent fuel reprocessing by advanced separation, impact of the presence of actinides on PWRs and FBRs operation. The efficiency of the different scenarios on the abatement of wastes radio-toxicity is presented in conclusion. (J.S.)

A detailed study of inexpensive radon control techniques in New York state houses

International Nuclear Information System (INIS)

Nitschke, I.A.; Wadach, J.B.; Clarke, W.A.; Traynor, G.W.; Adams, G.P.; Rizzuto, J.E.

1984-01-01

As part of a comprehensive indoor air quality and infiltration field study, radon concentrations were measured in 60 houses in upstate New York using passive integrating monitors. Indoor air radon concentrations ranged from 0.2 pCi/l to 50 pCi/l. Four houses with the highest radon levels were then extensively monitored using real-time continuous instruments for the measurement of radon, radon daughters, respirable particles, infiltration, inside-outside pressure difference, and weather parameters. Several inexpensive radon mitigation techniques were tested in these four houses. Their effectiveness ranged widely. Techniques identified as effective were permanently installed in 14 houses having indoor air radon concentration above 2 pCi/l. Finally, the long-term effectiveness of the installed control techniques is being tested using passive integrating radon monitors. (Author)

Battery Test Manual For 48 Volt Mild Hybrid Electric Vehicles

Energy Technology Data Exchange (ETDEWEB)

Walker, Lee Kenneth [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-03-01

This manual details the U.S. Advanced Battery Consortium and U.S. Department of Energy Vehicle Technologies Program goals, test methods, and analysis techniques for a 48 Volt Mild Hybrid Electric Vehicle system. The test methods are outlined stating with characterization tests, followed by life tests. The final section details standardized analysis techniques for 48 V systems that allow for the comparison of different programs that use this manual. An example test plan is included, along with guidance to filling in gap table numbers.

Battery Test Manual For 48 Volt Mild Hybrid Electric Vehicles

International Nuclear Information System (INIS)

Walker, Lee Kenneth

2017-01-01

This manual details the U.S. Advanced Battery Consortium and U.S. Department of Energy Vehicle Technologies Program goals, test methods, and analysis techniques for a 48 Volt Mild Hybrid Electric Vehicle system. The test methods are outlined stating with characterization tests, followed by life tests. The final section details standardized analysis techniques for 48 V systems that allow for the comparison of different programs that use this manual. An example test plan is included, along with guidance to filling in gap table numbers.

ID-Check: Online Concealed Information Test Reveals True Identity.

Science.gov (United States)

Verschuere, Bruno; Kleinberg, Bennett

2016-01-01

The Internet has already changed people's lives considerably and is likely to drastically change forensic research. We developed a web-based test to reveal concealed autobiographical information. Initial studies identified a number of conditions that affect diagnostic efficiency. By combining these moderators, this study investigated the full potential of the online ID-check. Participants (n = 101) tried to hide their identity and claimed a false identity in a reaction time-based Concealed Information Test. Half of the participants were presented with personal details (e.g., first name, last name, birthday), whereas the others only saw irrelevant details. Results showed that participants' true identity could be detected with high accuracy (AUC = 0.98; overall accuracy: 86-94%). Online memory detection can reliably and validly detect whether someone is hiding their true identity. This suggests that online memory detection might become a valuable tool for forensic applications. © 2015 American Academy of Forensic Sciences.

Investigation of the hydrodynamic model test of forced rolling for a barge using PIV

Directory of Open Access Journals (Sweden)

WANG Xiaoqiang

2017-03-01

Full Text Available In order to study the physical details of viscous flow in ship roll motions and improve the accuracy of ship roll damping numerical simulation, the application of the Particle Image Velocimetry (PIV technique is investigated in model tests of forced ship rolling in calm water. The hydrodynamic force and flow field at the bilge region are simultaneously measured for barges at different amplitudes and frequencies in which the self-made forced rolling facility was used. In the model test, the viscous flow variation with the time around the bilge region was studied during ship rolling motion. The changes in ship roll damping coefficients with the rolling amplitude and period were also investigated. A comparison of the model test results with the Computational Fluid Dynamics(CFDresults shows that the numerical ship roll damping coefficients agree well with the model test results, while the differences in the local flow details exist between the CFD results and model test results. Further research into the model test technique and CFD application is required.

Are medical articles highlighting detailed statistics more cited?

Directory of Open Access Journals (Sweden)

Mike Thelwall

2015-06-01

Full Text Available When conducting a literature review, it is natural to search for articles and read their abstracts in order to select papers to read fully. Hence, informative abstracts are important to ensure that research is read. The description of a paper's methods may help to give confidence that a study is of high quality. This article assesses whether medical articles that mention three statistical methods, each of which is arguably indicative of a more detailed statistical analysis than average, are more highly cited. The results show that medical articles mentioning Bonferroni corrections, bootstrapping and effect size tend to be 7%, 8% and 15% more highly ranked for citations than average, respectively. Although this is consistent with the hypothesis that mentioning more detailed statistical techniques generate more highly cited research, these techniques may also tend to be used in more highly cited areas of Medicine.

Evaluation of surface detail reproduction, dimensional stability and gypsum compatibility of monophase polyvinyl-siloxane and polyether elastomeric impression materials under dry and moist conditions.

Science.gov (United States)

Vadapalli, Sriharsha Babu; Atluri, Kaleswararao; Putcha, Madhu Sudhan; Kondreddi, Sirisha; Kumar, N Suman; Tadi, Durga Prasad

2016-01-01

This in vitro study was designed to compare polyvinyl-siloxane (PVS) monophase and polyether (PE) monophase materials under dry and moist conditions for properties such as surface detail reproduction, dimensional stability, and gypsum compatibility. Surface detail reproduction was evaluated using two criteria. Dimensional stability was evaluated according to American Dental Association (ADA) specification no. 19. Gypsum compatibility was assessed by two criteria. All the samples were evaluated, and the data obtained were analyzed by a two-way analysis of variance (ANOVA) and Pearson's Chi-square tests. When surface detail reproduction was evaluated with modification of ADA specification no. 19, both the groups under the two conditions showed no significant difference statistically. When evaluated macroscopically both the groups showed statistically significant difference. Results for dimensional stability showed that the deviation from standard was significant among the two groups, where Aquasil group showed significantly more deviation compared to Impregum group (P < 0.001). Two conditions also showed significant difference, with moist conditions showing significantly more deviation compared to dry condition (P < 0.001). The results of gypsum compatibility when evaluated with modification of ADA specification no. 19 and by giving grades to the casts for both the groups and under two conditions showed no significant difference statistically. Regarding dimensional stability, both impregum and aquasil performed better in dry condition than in moist; impregum performed better than aquasil in both the conditions. When tested for surface detail reproduction according to ADA specification, under dry and moist conditions both of them performed almost equally. When tested according to macroscopic evaluation, impregum and aquasil performed significantly better in dry condition compared to moist condition. In dry condition, both the materials performed almost equally. In

Toroidal simulation magnet tests

International Nuclear Information System (INIS)

Walstrom, P.L.; Domm, T.C.

1975-01-01

A number of different schemes for testing superconducting coils in a simulated tokamak environment are analyzed for their merits relative to a set of test criteria. Two of the concepts are examined in more detail: the so-called cluster test scheme, which employs two large background field coils, one on either side of the test coil, and the compact torus, a low-aspect ratio toroidal array of a small number of coils in which all of the coils are essentially test coils. Simulation of the pulsed fields of the tokamak is discussed briefly

Phased Startup Initiative Phases 3 and 4 Test Plan and Test Specification (OCRWM)

International Nuclear Information System (INIS)

PITNER, A.L.

2000-01-01

Construction for the Spent Nuclear Fuel (SNF) Project facilities is continuing per the Level III Baseline Schedule, and installation of the Fuel Retrieval System (FRS) and Integrated Water Treatment System (IWTS) in K West Basin is now complete. In order to accelerate the project, a phased start up strategy to initiate testing of the FRS and IWTS early in the overall project schedule was proposed (Williams 1999). Wilkinson (1999) expands the definition of the original proposal into four functional testing phases of the Phased Startup Initiative (PSI). Phases 1 and 2 are based on performing functional tests using dummy fuel. These tests are described in separate planning documents. This test plan provides overall guidance for Phase 3 and 4 tests, which are performed using actual irradiated N fuel assemblies. The overall objective of the Phase 3 and 4 testing is to verify how the FRS and IWTS respond while processing actual fuel. Conducting these tests early in the project schedule will allow identification and resolution of equipment and process problems before they become activities on the start-up critical path. The specific objectives of this test plan are to: (1) Define the test scope for the FRS and IWTS; (2) Provide detailed test requirements that can be used to write the specific test procedures; (3) Define data required and measurements to be taken. Where existing methods to obtain these do not exist, enough detail will be provided to define required additional equipment; and (4) Define specific test objectives and acceptance criteria

Can a significance test be genuinely Bayesian?

OpenAIRE

Pereira, Carlos A. de B.; Stern, Julio Michael; Wechsler, Sergio

2008-01-01

The Full Bayesian Significance Test, FBST, is extensively reviewed. Its test statistic, a genuine Bayesian measure of evidence, is discussed in detail. Its behavior in some problems of statistical inference like testing for independence in contingency tables is discussed.

Understanding brains: details, intuition, and big data.

Science.gov (United States)

Marder, Eve

2015-05-01

Understanding how the brain works requires a delicate balance between the appreciation of the importance of a multitude of biological details and the ability to see beyond those details to general principles. As technological innovations vastly increase the amount of data we collect, the importance of intuition into how to analyze and treat these data may, paradoxically, become more important.

Understanding Brains: Details, Intuition, and Big Data

OpenAIRE

Marder, Eve

2015-01-01

Understanding how the brain works requires a delicate balance between the appreciation of the importance of a multitude of biological details and the ability to see beyond those details to general principles. As technological innovations vastly increase the amount of data we collect, the importance of intuition into how to analyze and treat these data may, paradoxically, become more important.

Understanding brains: details, intuition, and big data.

Directory of Open Access Journals (Sweden)

Eve Marder

2015-05-01

Full Text Available Understanding how the brain works requires a delicate balance between the appreciation of the importance of a multitude of biological details and the ability to see beyond those details to general principles. As technological innovations vastly increase the amount of data we collect, the importance of intuition into how to analyze and treat these data may, paradoxically, become more important.

The improvement of dynamic universal testing machine for hot cell usages

International Nuclear Information System (INIS)

Ahn, Sang Bok; Lee, Key Soon; Park, Dae Kyu; Hong, Kwon Pyo; Choo, Yong Sun

1998-01-01

Dynamic universal testing machine(UTM) were developed for hot cell usages, which can perform tensile, compression, bending, fracture toughness and fatigue crack growth tests. In this report, technical reviews in the course of developing machine were described. Detailed subjects are as follows; 1. Outline of testing method using dynamic UTM 2. Detailed testing system organizations 3. Technical specification to develop machine 4. Setting up load string 5. Inspection and pre-commissioning tests on machine. (author). 14 figs

Hydraulic model tests of an innovative dike crest design

NARCIS (Netherlands)

Verhagen, H.J.; Kortenhaus, A.; Bollinger, K.; Dassayanake, D.

2007-01-01

Report on laboratory tests on a crest drainage dike; investigation if a channel in the crest of the dike is able to decrease the amount of overtopping over the dike. Chapter 2 provides details about findings from previous studies and the relevance of those findings to this research project.

Numerical optimization of conical flow waveriders including detailed viscous effects

Science.gov (United States)

Bowcutt, Kevin G.; Anderson, John D., Jr.; Capriotti, Diego

1987-01-01

A family of optimized hypersonic waveriders is generated and studied wherein detailed viscous effects are included within the optimization process itself. This is in contrast to previous optimized waverider work, wherein purely inviscid flow is used to obtain the waverider shapes. For the present waveriders, the undersurface is a streamsurface of an inviscid conical flowfield, the upper surface is a streamsurface of the inviscid flow over a tapered cylinder (calculated by the axisymmetric method of characteristics), and the viscous effects are treated by integral solutions of the boundary layer equations. Transition from laminar to turbulent flow is included within the viscous calculations. The optimization is carried out using a nonlinear simplex method. The resulting family of viscous hypersonic waveriders yields predicted high values of lift/drag, high enough to break the L/D barrier based on experience with other hypersonic configurations. Moreover, the numerical optimization process for the viscous waveriders results in distinctly different shapes compared to previous work with inviscid-designed waveriders. Also, the fine details of the viscous solution, such as how the shear stress is distributed over the surface, and the location of transition, are crucial to the details of the resulting waverider geometry. Finally, the moment coefficient variations and heat transfer distributions associated with the viscous optimized waveriders are studied.

GIS-assisted spatial analysis for urban regulatory detailed planning: designer's dimension in the Chinese code system

Science.gov (United States)

Yu, Yang; Zeng, Zheng

2009-10-01

By discussing the causes behind the high amendments ratio in the implementation of urban regulatory detailed plans in China despite its law-ensured status, the study aims to reconcile conflict between the legal authority of regulatory detailed planning and the insufficient scientific support in its decision-making and compilation by introducing into the process spatial analysis based on GIS technology and 3D modeling thus present a more scientific and flexible approach to regulatory detailed planning in China. The study first points out that the current compilation process of urban regulatory detailed plan in China employs mainly an empirical approach which renders it constantly subjected to amendments; the study then discusses the need and current utilization of GIS in the Chinese system and proposes the framework of a GIS-assisted 3D spatial analysis process from the designer's perspective which can be regarded as an alternating processes between the descriptive codes and physical design in the compilation of regulatory detailed planning. With a case study of the processes and results from the application of the framework, the paper concludes that the proposed framework can be an effective instrument which provides more rationality, flexibility and thus more efficiency to the compilation and decision-making process of urban regulatory detailed plan in China.

Feasibly study of gas-cooled test cell for material testing in IFMIF

International Nuclear Information System (INIS)

Yonemoto, Yukihiro; Maki, Eiji; Ebara, Shinji; Yokomine, Takehiko; Shimizu, Akihiko; Korenaga, Tadashi

2002-01-01

Temperature control performance of test pieces enclosed in IFMIF capsule by using single phase gas was estimated experimentally. The key issue of this study is to obtain the definite value of dimension of test facility and flow conditions of coolant and to clarify the temperature response of test piece to the beam-off scenario. Firstly, we have examined the cooling performance of the test cell originally proposed in IFMIF-KEP and from results of this calculation performed in three dimensional system by using brand-new turbulence model for flow and thermal fields, it is concluded that the drastical change of design of test cell is needed in order to obtain the unformity of temperature of test piece, to improve the responsibility of temperature measurement of test piece, and to relieve the coolant flow condition, especially for inlet pressure value. Thus, we have proposed new design of test cell and test piece arrangement. A mock-up experimental facility was made based on our design and preliminary experiments for temperature control were performed. As a result, we have verified the cooling performance at the case that corresponds to two beam-off scenario by using mock-up facility

Assembly and installation of the large coil test facility test stand

International Nuclear Information System (INIS)

Queen, C.C. Jr.

1983-01-01

The Large Coil Test Facility (LCTF) was built to test six tokamak-type superconducting coils, with three to be designed and built by US industrial teams and three provided by Japan, Switzerland, and Euratom under an international agreement. The facility is designed to test these coils in an environment which simulates that of a tokamak. The heart of this facility is the test stand, which is made up of four major assemblies: the Gravity Base Assembly, the Bucking Post Assembly, the Torque Ring Assembly, and the Pulse Coil Assembly. This paper provides a detailed review of the assembly and installation of the test stand components and the handling and installation of the first coil into the test stand

Postlearning stress differentially affects memory for emotional gist and detail in naturally cycling women and women on hormonal contraceptives.

Science.gov (United States)

Nielsen, Shawn E; Ahmed, Imran; Cahill, Larry

2014-08-01

Sex differences in emotional memory have received increasing interest over the past decade. However, to date, no work has explored how a postlearning stressor might modulate the influence of sex hormone status on memory for gist and peripheral detail in an emotional versus neutral context. Here, we tested 3 predictions. First, compared with naturally cycling (NC) women in the luteal phase, women on hormonal contraception (HC) would have significantly blunted hypothalamic-pituitary-adrenal reactivity to physical stress. Second, postlearning stress would enhance detail and gist memory from an emotional story in NC women, and finally, postlearning stress would not affect emotional memory for details or gist in HC women. Healthy NC and HC women viewed a brief, narrated story containing neutral or emotionally arousing elements. Immediately after, cold pressor stress (CPS) or a control procedure was administered. One week later, participants received a surprise free recall test for story elements. NC women exhibited significantly greater cortisol increases to CPS compared with HC women. NC women who viewed the emotional story and were administered CPS recalled the most peripheral details overall and more gist from the emotional compared with the neutral story. In HC women, however, the postlearning cortisol release did not affect memory for gist or peripheral details from the emotional or neutral story in any way. Additionally, NC and HC women performed similarly on measures of attention and arousal. These findings suggest that in women, postlearning stress differentially affects memory for emotional information depending on their hormonal contraceptive status.

Test Automation Process Improvement A case study of BroadSoft

OpenAIRE

Gummadi, Jalendar

2016-01-01

This master thesis research is about improvement of test automation process at BroadSoft Finland as a case study. Test automation project recently started at BroadSoft but the project is not properly integrated in to existing process. Project is about converting manual test cases to automation test cases. The aim of this thesis is about studying existing BroadSoft test process and studying different test automation frameworks. In this thesis different test automation process are studied ...

Test-Retest Reliability of a Survey to Measure Transport-Related Physical Activity in Adults

Science.gov (United States)

Badland, Hannah; Schofield, Grant

2006-01-01

The present research details test-retest reliability of a newly developed, telephone-administered TPA survey for adults. This instrument examines barriers, perceptions, and current travel behaviors to place of work/study and local convenience shops. Demonstrated test-retest reliability of the Active Friendly Environments-Transport-Related Physical…

Strategy for Alternative Occupant Volume Testing

Science.gov (United States)

2009-10-20

This paper describes plans for a series of quasi-static : compression tests of rail passenger equipment. These tests are : designed to evaluate the strength of the occupant volume under : static loading conditions. The research plan includes a detail...

Ice condenser testing facility and plans

International Nuclear Information System (INIS)

Kannberg, L.D.; Ross, B.A.; Eschbach, E.J.; Ligotke, M.W.

1987-01-01

A facility is being constructed to experimentally validate the ICEDF computer code. The code was developed to estimate the extent of fission product retention in the ice compartments of pressurized water reactor ice condenser containment systems during severe accidents. The design and construction of the facility is based on a test design that addresses the validation needs of the code for conditions typical of those expected to occur during severe pressurized water reactor accidents. Detailed facility design has followed completion of a test design (i.e., assembled test cases each involving a different set of aerosol and thermohydraulic flow conditions). The test design was developed with the aid of statistical test design software and was scrutinized for applicability with the aid of ICEDF simulations. The test facility will incorporate a small section of a prototypic ice condenser (e.g., a cross section comprising the equivalent of four 1-ft-diameter ice baskets to their full prototypic height of 48 ft). The development of the test design, the detailed facility design, and the construction progress are described in this paper

Detailed study of electron plasma waves upstream of the earth's bow shock

International Nuclear Information System (INIS)

Etcheto, J.; Faucheux, M.

1984-01-01

A detailed study of electron plasma waves observed upstream of the earth's bow shock and of their relationships to the position of the satellite in the foreshock and to the electron measurements has been carried out. The wave characteristics depend on the position in the electron foreshock: a narrow-bnd (a few percent) and intense (a few millivolts per meter) noise is observed at the plasma frequency at the edge of the foreshock while the spectrum widens (Δf/fapprox. =0.3) at the same time as the power decreases (hundreds of microvolts per meter) deeper (a few earth radii) inside the foreshock. Signals below the plasma frequency are also observed. These waves are polarized along the magnetic field, with long wavelengths below and at the plasma frequency and short wavelengths above it. They appear as short bursts, the duration of which depends on the frequency: longer close to the plasma frequency (50 ms), they shorten with increasing separation from the plasma frequency, the usual duration being 15 ms. While the correlation of the wave characteristics with the reflected electrons is good as the satellite moves inside the foreshock, no evolution is found with the distance to the bow shock, neither for the noise nor for the particles. These results are discussed in the frame of various mechanisms which have been proposed to explain these upstream waves but no satisfactory agreement is found with any of them

Overview of multi-input frequency domain modal testing methods with an emphasis on sine testing

Science.gov (United States)

Rost, Robert W.; Brown, David L.

1988-01-01

An overview of the current state of the art multiple-input, multiple-output modal testing technology is discussed. A very brief review of the current time domain methods is given. A detailed review of frequency and spatial domain methods is presented with an emphasis on sine testing.

Case Study of Lessons Learned from the Operation of the Fast Flux Test Facility

International Nuclear Information System (INIS)

Wootan, D.; Omberg, R.; Grandy, C.

2016-01-01

Full text: The lessons learned approach being followed at the Fast Flux Test Facility is to have domain experts in each subject area develop a short write-up or report on each lesson learned. Each lesson learned write-up is on the order of 4–6 pages. Longer reports can be developed as needed. Each lessons learned summary discusses the problem and the resolution method employed to address the problem, and also tries to capture the essential “tacit knowledge” associated with each topic in a focused manner. All lessons learned write-ups are supported by more detailed documents. For example, references of more detailed reports are generally included, where available. Topics are selected as those most likely to apply to future design or operating problems. This lessons learned approach has been successful in capturing essential tacit knowledge about key events in FFTF history and providing a context for interpreting the existing data and references. (author

Knowing thy enemy : detailed study of coiled tubing's breaking point in sour conditions is leading to failure avoidance

Energy Technology Data Exchange (ETDEWEB)

Smith, M.

2007-03-15

Well failures arising from coiled tubing (CT) in sour oil and gas environments can result in the loss of millions of dollars. This article examined some of the causes of CT well failures in Alberta, and provided details of joint industry projects (JIPs) headed by BJ Services Company currently investigating the chemical reactions related to the degradation of CT materials. Degradation of CT tools can be caused hydrogen-induced cracking (HIC); sulphide stress cracking; step-wise cracking; stress-oriented HIC; and blistering. CT is repeatedly wound off and onto a reel when cycled in and out of wells, and can accumulate both low-cycle fatigue and surface damage over time, either of which can lead to failures. Exposure to hydrogen sulphide (H{sub 2}S) significantly reduces the lifespan of CT. When H{sub 2}S is in an aqueous environment or solution and comes into contact with steel, chemical reactions take place on the surface of the steel that generate atomic hydrogen, which causes the steel to become brittle. Cracking can also occur as a result of the hydrogen atoms within the steel matrix recombining to form hydrogen molecules, or as the result of applying a stress above threshold limits. Tests are now being conducted at a Shell laboratory to expose CT specimens to H{sub 2}S. After immersion, the steel specimens are then maintained in a -78.5 degrees C environment so that the H{sub 2}S is locked into the steel. Acoustic emission sensors are wired to a monitoring system to determine both when cracks occur and under what conditions of load or severity of environment. A bend fatigue machine is also used to cycle CT through a bend and straighten sequence. Samples also undergo constant load testing, hydrogen diffusion cell testing and external mechanical damage assessments. The effect of H{sub 2}S on bias and butt welds is also studied. Efforts are also being made to improve the CT steel manufacturing process. Results of the JIP have led researchers to conclude that

Development and testing of incident detection algorithms. Vol. 2, research methodology and detailed results.

Science.gov (United States)

1976-04-01

The development and testing of incident detection algorithms was based on Los Angeles and Minneapolis freeway surveillance data. Algorithms considered were based on times series and pattern recognition techniques. Attention was given to the effects o...

Eliciting preferences for priority setting in genetic testing: a pilot study comparing best-worst scaling and discrete-choice experiments.

Science.gov (United States)

Severin, Franziska; Schmidtke, Jörg; Mühlbacher, Axel; Rogowski, Wolf H

2013-11-01

Given the increasing number of genetic tests available, decisions have to be made on how to allocate limited health-care resources to them. Different criteria have been proposed to guide priority setting. However, their relative importance is unclear. Discrete-choice experiments (DCEs) and best-worst scaling experiments (BWSs) are methods used to identify and weight various criteria that influence orders of priority. This study tests whether these preference eliciting techniques can be used for prioritising genetic tests and compares the empirical findings resulting from these two approaches. Pilot DCE and BWS questionnaires were developed for the same criteria: prevalence, severity, clinical utility, alternatives to genetic testing available, infrastructure for testing and care established, and urgency of care. Interview-style experiments were carried out among different genetics professionals (mainly clinical geneticists, researchers and biologists). A total of 31 respondents completed the DCE and 26 completed the BWS experiment. Weights for the levels of the six attributes were estimated by conditional logit models. Although the results derived from the DCE and BWS experiments differed in detail, we found similar valuation patterns in the DCE and BWS experiments. The respondents attached greatest value to tests with high clinical utility (defined by the availability of treatments that reduce mortality and morbidity) and to testing for highly prevalent conditions. The findings from this study exemplify how decision makers can use quantitative preference eliciting methods to measure aggregated preferences in order to prioritise alternative clinical interventions. Further research is necessary to confirm the survey results.

Marine Hydrokinetic (MHK) Energy Conversion Research at UNH: From Fundamental Studies of Hydrofoil Sections, to Moderate Reynolds Number Turbine Tests in a Tow Tank, to Open Water Deployments at Tidal Energy Test Sites (Invited)

Science.gov (United States)

Wosnik, M.; Bachant, P.; Nedyalkov, I.; Rowell, M.; Dufresne, N.; Lyon, V.

2013-12-01

We report on research related to MHK turbines at the Center for Ocean Renewable Energy (CORE) at the University of New Hampshire (UNH). The research projects span varies scales, levels of complexity and environments - from fundamental studies of hydrofoil sections in a high speed water tunnel, to moderate Reynolds number turbine tests with inflow and wake studies in a large cross-section tow tank, to deployments of highly instrumented process models at tidal energy test sites in New England. A concerted effort over the past few years has brought significant new research infrastructure for marine hydrokinetic energy conversion online at UNH-CORE. It includes: a high-speed cavitation tunnel with independent control of velocity and pressure; a highly accurate tow mechanism, turbine test bed and wake traversing system for the 3.7m x 2.4m cross-section UNH tow tank; a 10.7m x 3.0m tidal energy test platform which can accommodate turbines up to 1.5m in diameter, for deployments at the UNH-CORE Tidal Energy Test Site in Great Bay Estuary, NH, a sheltered 'nursery site' suitable for intermediate scale tidal energy conversion device testing with peak currents typically above 2 m/s during each tidal cycle. Further, a large boundary layer wind tunnel, the new UNH Flow Physics Facility (W6.0m x H2.7m xL72m) is being used for detailed turbine wake studies, producing data and insight also applicable to MHK turbines in low Froude number deployments. Bi-directional hydrofoils, which perform equally well in either flow direction and could avoid the use of complex and maintenance-intensive yaw or blade pitch mechanisms, are being investigated theoretically, numerically and experimentally. For selected candidate shapes lift, drag, wake, and cavitation inception/desinence are measured. When combined with a cavitation inception model for MHK turbines, this information can be used to prescribe turbine design/operational parameters. Experiments were performed with a 1m diameter and 1m

Initial field testing definition of subsurface sealing and backfilling tests in unsaturated tuff

International Nuclear Information System (INIS)

Fernandez, J.A.; Case, J.B.; Tyburski, J.R.

1993-05-01

This report contains an initial definition of the field tests proposed for the Yucca Mountain Project repository sealing program. The tests are intended to resolve various performance and emplacement concerns. Examples of concerns to be addressed include achieving selected hydrologic and structural requirements for seals, removing portions of the shaft liner, excavating keyways, emplacing cementitious and earthen seals, reducing the impact of fines on the hydraulic conductivity of fractures, efficient grouting of fracture zones, sealing of exploratory boreholes, and controlling the flow of water by using engineered designs. Ten discrete tests are proposed to address these and other concerns. These tests are divided into two groups: Seal component tests and performance confirmation tests. The seal component tests are thorough small-scale in situ tests, the intermediate-scale borehole seal tests, the fracture grouting tests, the surface backfill tests, and the grouted rock mass tests. The seal system tests are the seepage control tests, the backfill tests, the bulkhead test in the Calico Hills unit, the large-scale shaft seal and shaft fill tests, and the remote borehole sealing tests. The tests are proposed to be performed in six discrete areas, including welded and non-welded environments, primarily located outside the potential repository area. The final selection of sealing tests will depend on the nature of the geologic and hydrologic conditions encountered during the development of the Exploratory Studies Facility and detailed numerical analyses. Tests are likely to be performed both before and after License Application

Airborne gamma-ray spectrometer and magnetometer survey, Durango C, Colorado. Final report Volume II A. Detail area

International Nuclear Information System (INIS)

1983-01-01

Geology of Durango C detail area, radioactive mineral occurrences in Colorado, and geophysical data interpretation are included in this report. Eight appendices provide: stacked profiles, geologic histograms, geochemical histograms, speed and altitude histograms, geologic statistical tables, magnetic and ancillary profiles, and test line data

Test plan for engineering scale electrostatic enclosure demonstration

International Nuclear Information System (INIS)

Meyer, L.C.

1993-02-01

This test plan describes experimental details of an engineering-scale electrostatic enclosure demonstration to be performed at the Idaho National Engineering Laboratory in fiscal year (FY)-93. This demonstration will investigate, in the engineering scale, the feasibility of using electrostatic enclosures and devices to control the spread of contaminants during transuranic waste handling operations. Test objectives, detailed experimental procedures, and data quality objectives necessary to perform the FY-93 experiments are included in this plan

Certification testing at low temperatures

International Nuclear Information System (INIS)

Noss, P.W.; Ammerman, D.J.

2004-01-01

Regulations governing the transport of radioactive materials require that most hypothetical accident condition tests or analyses consider the effects of the environmental temperature that most challenges package performance. For many packages, the most challenging temperature environment is the cold condition (-29 C according to U.S. regulations), primarily because the low temperature causes the highest free drop impact forces due to the higher strength of many energy-absorbing materials at this temperature. If it is decided to perform low temperature testing, it is only necessary that the relevant parts of the package have the required temperature prior to the drop. However, the details of performing a drop at low temperature can have a large influence on testing cost and technical effectiveness. The selection of the test site, the chamber and type of chilling equipment, instrumentation, and even the time of year are all important. Control of seemingly minor details such as the effect on internal pressure, placement of monitoring thermocouples, the thermal time constant of the test article, and icing of equipment are necessary to ensure a successful low temperature test. This paper will discuss these issues and offer suggestions based on recent experience

A detailed safety assessment of a saw palmetto extract.

Science.gov (United States)

Avins, Andrew L; Bent, Stephen; Staccone, Suzanne; Badua, Evelyn; Padula, Amy; Goldberg, Harley; Neuhaus, John; Hudes, Esther; Shinohara, Katusto; Kane, Christopher

2008-06-01

Saw palmetto is commonly used by men for lower-urinary tract symptoms. Despite its widespread use, very little is known about the potential toxicity of this dietary supplement. The Saw palmetto for Treatment of Enlarged Prostates (STEP) study was a randomized clinical trial performed among 225 men with moderate-to-severe symptoms of benign prostatic hyperplasia, comparing a standardized extract of the saw palmetto berry (160 mg twice daily) with a placebo over a 1-year period. As part of this study, detailed data were collected on serious and non-serious adverse events, sexual functioning, and laboratory tests of blood and urine. Between-group differences were assessed with mixed-effects regression models. There were no significant differences observed between the saw palmetto and placebo-allocated participants in the risk of suffering at least one serious adverse event (5.4% vs. 9.7%, respectively; p=0.31) or non-serious symptomatic adverse event (34.8% vs. 30.1%, p=0.48). There were few significant between-group differences in sexual functioning or for most laboratory analyses, with only small differences observed in changes over time in total bilirubin (p=0.001), potassium (p=0.03), and the incidence of glycosuria (0% in the saw palmetto group vs. 3.7% in the placebo group, p=0.05). Despite careful assessment, no evidence for serious toxicity of saw palmetto was observed in this clinical trial. Given the sample size and length of this study, however, these data do not rule out potential rare adverse effects associated with the use of saw palmetto.

A detailed phylogeny for the Methanomicrobiales

Science.gov (United States)

Rouviere, P.; Mandelco, L.; Winker, S.; Woese, C. R.

1992-01-01

The small subunit rRNA sequence of twenty archaea, members of the Methanomicrobiales, permits a detailed phylogenetic tree to be inferred for the group. The tree confirms earlier studies, based on far fewer sequences, in showing the group to be divided into two major clusters, temporarily designated the "methanosarcina" group and the "methanogenium" group. The tree also defines phylogenetic relationships within these two groups, which in some cases do not agree with the phylogenetic relationships implied by current taxonomic names--a problem most acute for the genus Methanogenium and its relatives. The present phylogenetic characterization provides the basis for a consistent taxonomic restructuring of this major methanogenic taxon.

Diagnostic value of scratch-chamber test, skin prick test, histamine release and specific IgE in birch-allergic patients with oral allergy syndrome to apple

DEFF Research Database (Denmark)

Osterballe, M; Scheller, R; Stahl Skov, P

2003-01-01

BACKGROUND: The aim of the study was to examine the diagnostic value of skin prick test (SPT), scratch-chamber test (SCT), histamine release (HR) and specific immunoglobulin E (IgE) in birch-allergic patients with oral allergy syndrome to apple. METHODS: Ten birch-allergic patients with oral...... a detailed case history about symptoms of oral allergy syndrome combined with a SPT with fresh apple peel or A72 will be useful....

Nuclear Weak Rates and Detailed Balance in Stellar Conditions

Energy Technology Data Exchange (ETDEWEB)

Misch, G. Wendell, E-mail: wendell@sjtu.edu, E-mail: wendell.misch@gmail.com [Department of Physics and Astronomy, Shanghai Jiao Tong University, 800 Dong Chuan Road, Shanghai 200240 (China)

2017-07-20

Detailed balance is often invoked in discussions of nuclear weak transitions in astrophysical environments. Satisfaction of detailed balance is rightly touted as a virtue of some methods of computing nuclear transition strengths, but I argue that it need not necessarily be strictly obeyed in astrophysical environments, especially when the environment is far from weak equilibrium. I present the results of shell model calculations of nuclear weak strengths in both charged-current and neutral-current channels at astrophysical temperatures, finding some violation of detailed balance. I show that a slight modification of the technique to strictly obey detailed balance has little effect on the reaction rates associated with these strengths under most conditions, though at high temperature the modified technique in fact misses some important strength. I comment on the relationship between detailed balance and weak equilibrium in astrophysical conditions.

Emotional intelligence and reasoning tests: a correlacional study / Inteligência emocional e provas de raciocínio: um estudo correlacional