Evaluation test on stability of high temperature strain gage

Energy Technology Data Exchange (ETDEWEB)

Sato, Toshimi (Kyowa Electronic Instruments Co. Ltd., Tokyo (Japan)); Ito, Haruhiko; Tanaka, Isao; Komori, Yoshihiro

1983-08-01

This report deals with the results on a stability test of high temperature strain gage which is utilized for development of the Stethoscope for OGL - 1 Components in Elevated Temperature Services (ab. SOCETS). The test has proved that the weldable strain gage (KHC - 20 - G5) exhibits excellent stability at 500/sup 0/C during 3000 to 4000 hours service and can be applied sufficiently to evaluate integrity of OGL - 1 high temperature pipings and others.

Evaluation test on stability of high temperature strain gage

International Nuclear Information System (INIS)

Sato, Toshimi; Ito, Haruhiko; Tanaka, Isao; Komori, Yoshihiro.

1983-01-01

This report deals with the results on a stability test of high temperature strain gage which is utilized for development of the Stethoscope for OGL - 1 Components in Elevated Temperature Services (ab. SOCETS). The test has proved that the weldable strain gage (KHC - 20 - G5) exhibits excellent stability at 500 0 C during 3000 to 4000 hours service and can be applied sufficiently to evaluate integrity of OGL - 1 high temperature pipings and others. (author)

One- and multistage total strain and stress-controlled fatigue tests with a steel of type 42 CrMo 4 subject to varied residual and mean stress loading. Final report

International Nuclear Information System (INIS)

Macherauch, E.; Schulze, V.

1995-01-01

Work under this research project covered tests with the quenched and tempered steel 42 CrMo 4 to which one- and two-stage tension-compression fatigue stresses were applied with varying mean loads, under conditions of nominal stress and total strain control. Shot peening was used to induce various microstructural conditions in the material at the surface and near below. Softening in the material was observed to be a continuous process, and the steel showed no stabilised, cyclic deformation behaviour. The cyclic stress-strain curve measured with equal stress amplitudes and total strain control applied shows higher plastic strain amplitudes than that measured with nominal stresses. The fatigue behaviour under two-stage loading depends on the chosen sequence of loads applied, the testing periods, and the overall testing procedure, so that there is no way of deriving data for two-stage testing procedures from single-stage test results. (orig.) [de

Localized strain measurements of the intervertebral disc annulus during biaxial tensile testing.

Science.gov (United States)

Karakolis, Thomas; Callaghan, Jack P

2015-01-01

Both inter-lamellar and intra-lamellar failures of the annulus have been described as potential modes of disc herniation. Attempts to characterize initial lamellar failure of the annulus have involved tensile testing of small tissue samples. The purpose of this study was to evaluate a method of measuring local surface strains through image analysis of a tensile test conducted on an isolated sample of annular tissue in order to enhance future studies of intervertebral disc failure. An annulus tissue sample was biaxial strained to 10%. High-resolution images captured the tissue surface throughout testing. Three test conditions were evaluated: submerged, non-submerged and marker. Surface strains were calculated for the two non-marker conditions based on motion of virtual tracking points. Tracking algorithm parameters (grid resolution and template size) were varied to determine the effect on estimated strains. Accuracy of point tracking was assessed through a comparison of the non-marker conditions to a condition involving markers placed on tissue surface. Grid resolution had a larger effect on local strain than template size. Average local strain error ranged from 3% to 9.25% and 0.1% to 2.0%, for the non-submerged and submerged conditions, respectively. Local strain estimation has a relatively high potential for error. Submerging the tissue provided superior strain estimates.

Grimsel Test Site: heat test, final report

International Nuclear Information System (INIS)

Schneefuss, J.; Glaess, F.; Gommlich, G.; Schmidt, M.

1989-05-01

The Swiss concept for the storage of radioactive waste consists in placing it in compact, dense rock formations. An experiment 'Heat Test' carried out by the 'Gesellschaft fuer Strahlen- und Umweltforschung' in Nagra's Grimsel rock laboratory simulated the heat production of stored radioactive waste. The aim was to evaluate processes for the demonstration of the suitability of a final repository for heat-producing radioactive waste in cristalline rock, to investigate the thermic, mechanic and hydraulic reactions to an artificial heat source, and to develop corresponding calculating models. The duration of the tests was about 3 years. In this report the measured thermic, mechanic and hydraulic reactions are documented and discussed in detail. A simple, rotation symmetrical FEM-model was used for the preparatory and experiment-accompanying modelling of the thermomechanical conditions in the heat test. The test showed that suitable measuring methods for the surveillance of the geomechanics of a final repository are available and that the reactions of the crystalline host rock to the heat source remain locally limited and can be modelled with relatively small effort. 29 refs., 33 figs., 10 tabs

Modification of γ-induced mutagenesis in Ames test-strains

International Nuclear Information System (INIS)

Basha, S.G.; Krasavin, E.A.; Kozubek, S.; Amirtaev, K.G.

1990-01-01

Glycerine and cysteamine protective effect on mutagenesis was studied in 3 strains of Salmonella typhimurium under γ-radiation. Glycerine modifying effect was shown to be not similar for various test-strains and depended on DNA injury nature. DNA complex injuries were shown to play significant role in mutagenesis of TA100 and TA102 strains. Absence of cysteamine modifying effect on γ-induced mutagenesis testified to cysteamine effect on enzyme balance. 20 refs.; 2 figs.; 1 tab

Final focus test beam

International Nuclear Information System (INIS)

1991-03-01

This report discusses the following: the Final Focus Test Beam Project; optical design; magnets; instrumentation; magnetic measurement and BPM calibration; mechanical alignment and stabilization; vacuum system; power supplies; control system; radiation shielding and personnel protection; infrastructure; and administration

Standard test methods for performance characteristics of metallic bonded resistance strain gages

CERN Document Server

American Society for Testing and Materials. Philadelphia

1992-01-01

1.1 The purpose of this standard is to provide uniform test methods for the determination of strain gauge performance characteristics. Suggested testing equipment designs are included. 1.2 Test Methods E 251 describes methods and procedures for determining five strain gauge parameters: Section Part I—General Requirements 7 Part II—Resistance at a Reference Temperature 8 Part III—Gauge Factor at a Reference Temperature 9 Part IV—Temperature Coefficient of Gauge Factor\t10 Part V—Transverse Sensitivity\t11 Part VI—Thermal Output\t12 1.3 Strain gauges are very sensitive devices with essentially infinite resolution. Their response to strain, however, is low and great care must be exercised in their use. The performance characteristics identified by these test methods must be known to an acceptable accuracy to obtain meaningful results in field applications. 1.3.1 Strain gauge resistance is used to balance instrumentation circuits and to provide a reference value for measurements since all data are...

The testing effect for mediator final test cues and related final test cues in online and laboratory experiments.

Science.gov (United States)

Coppens, Leonora C; Verkoeijen, Peter P J L; Bouwmeester, Samantha; Rikers, Remy M J P

2016-05-31

The testing effect is the finding that information that is retrieved during learning is more often correctly retrieved on a final test than information that is restudied. According to the semantic mediator hypothesis the testing effect arises because retrieval practice of cue-target pairs (mother-child) activates semantically related mediators (father) more than restudying. Hence, the mediator-target (father-child) association should be stronger for retrieved than restudied pairs. Indeed, Carpenter (2011) found a larger testing effect when participants received mediators (father) than when they received target-related words (birth) as final test cues. The present study started as an attempt to test an alternative account of Carpenter's results. However, it turned into a series of conceptual (Experiment 1) and direct (Experiment 2 and 3) replications conducted with online samples. The results of these online replications were compared with those of similar existing laboratory experiments through small-scale meta-analyses. The results showed that (1) the magnitude of the raw mediator testing effect advantage is comparable for online and laboratory experiments, (2) in both online and laboratory experiments the magnitude of the raw mediator testing effect advantage is smaller than in Carpenter's original experiment, and (3) the testing effect for related cues varies considerably between online experiments. The variability in the testing effect for related cues in online experiments could point toward moderators of the related cue short-term testing effect. The raw mediator testing effect advantage is smaller than in Carpenter's original experiment.

Strain measurement based battery testing

Science.gov (United States)

Xu, Jeff Qiang; Steiber, Joe; Wall, Craig M.; Smith, Robert; Ng, Cheuk

2017-05-23

A method and system for strain-based estimation of the state of health of a battery, from an initial state to an aged state, is provided. A strain gauge is applied to the battery. A first strain measurement is performed on the battery, using the strain gauge, at a selected charge capacity of the battery and at the initial state of the battery. A second strain measurement is performed on the battery, using the strain gauge, at the selected charge capacity of the battery and at the aged state of the battery. The capacity degradation of the battery is estimated as the difference between the first and second strain measurements divided by the first strain measurement.

Study of creep behaviour in P-doped copper with slow strain rate tensile tests

International Nuclear Information System (INIS)

Xuexing Yao; Sandstroem, Rolf

2000-08-01

Pure copper with addition of phosphorous is planned to be used to construct the canisters for spent nuclear fuel. The copper canisters can be exposed to a creep deformation up to 2-4% at temperatures in services. The ordinary creep strain tests with dead weight loading are generally employed to study the creep behaviour; however, it is reported that an initial plastic deformation of 5-15% takes place when loading the creep specimens at lower temperatures. The slow strain rate tensile test is an alternative to study creep deformation behaviour of materials. Ordinary creep test and slow strain rate tensile test can give the same information in the secondary creep stage. The advantage of the tensile test is that the starting phase is much more controlled than in a creep test. In a tensile test the initial deformation behaviour can be determined and the initial strain of less than 5% can be modelled. In this study slow strain rate tensile tests at strain rate of 10 -4 , 10 -5 , 10 -6 , and 10 -7 /s at 75, 125 and 175 degrees C have been performed on P-doped pure Cu to supplement creep data from conventional creep tests. The deformation behaviour has successfully been modelled. It is shown that the slow strain rate tensile tests can be implemented to study the creep deformation behaviours of pure Cu

Fast recovery strain measurements in a nuclear test environment

International Nuclear Information System (INIS)

Kitchen, W.R.; Nauman, W.J.; Vollmer, D.W.

1979-01-01

The recovery of early-time (50 μs or less) strain gage data on structural response experiments in underground nuclear tests has been a continuing problem for experimenters at the Nevada Test Site. Strain measurement is one of the primary techniques used to obtain experimental data for model verification and correlation with predicted effects. Peak strains generally occur within 50 to 100 μs of the radiation exposure. Associated with the exposure is an intense electromagnetic impulse that produces potentials of kilovolts and currents of kiloamperes on the experimental structures. For successful operation, the transducer and associated recording system must recover from the initial noise overload and accurately track the strain response within about 50 μs of the nuclear detonation. A gaging and fielding technique and a recording system design that together accomplish these objectives are described. Areas discussed include: (1) noise source model; (2) experimental cassette design, gage application, grounding, and shielding; (3) cable design and shielding between gage and recorder; (4) recorder design including signal conditioner/amplifier, digital encoder, buffer memory, and uphole data transmission; and (5) samples of experimental data

Test and Numerical Analysis for Penetration Residual Velocity of Bullet Considering Failure Strain Uncertainty of Composite Plates

Energy Technology Data Exchange (ETDEWEB)

Cha, Myungseok; Lee, Minhyung [Sejong Univ., Sejong (Korea, Republic of)

2016-03-15

The ballistic performance data of composite materials is distributed due to material inhomogeneity. In this paper, the uncertainty in residual velocity is obtained experimentally, and a method of predicting it is established numerically for the high-speed impact of a bullet into laminated composites. First, the failure strain distribution was obtained by conducting a tensile test using 10 specimens. Next, a ballistic impact test was carried out for the impact of a fragment-simulating projectile (FSP) bullet with 4ply ([0/90]s) and 8ply ([0/90/0/90]s) glass fiber reinforced plastic (GFRP) plates. Eighteen shots were made at the same impact velocity and the residual velocities were obtained. Finally, simulations were conducted to predict the residual velocities by using the failure strain distributions that were obtained from the tensile test. For this simulation, two impact velocities were chosen at 411.7m/s (4ply) and 592.5m/s (8ply). The simulation results show that the predicted residual velocities are in close agreement with test results. Additionally, the modeling of a composite plate with layered solid elements requires less calculation time than modeling with solid elements.

Refinement of the wedge bar technique for compression tests at intermediate strain rates

Directory of Open Access Journals (Sweden)

Stander M.

2012-08-01

Full Text Available A refined development of the wedge-bar technique [1] for compression tests at intermediate strain rates is presented. The concept uses a wedge mechanism to compress small cylindrical specimens at strain rates in the order of 10s−1 to strains of up to 0.3. Co-linear elastic impact principles are used to accelerate the actuation mechanism from rest to test speed in under 300μs while maintaining near uniform strain rates for up to 30 ms, i.e. the transient phase of the test is less than 1% of the total test duration. In particular, a new load frame, load cell and sliding anvil designs are presented and shown to significantly reduce the noise generated during testing. Typical dynamic test results for a selection of metals and polymers are reported and compared with quasistatic and split Hopkinson pressure bar results.

High Strain Rate Testing of Welded DOP-26 Iridium

Energy Technology Data Exchange (ETDEWEB)

Schneibel, J. H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Miller, R. G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Carmichael, C. A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Fox, E. E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ulrich, G. B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); George, E. P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

The iridium alloy DOP-26 is used to produce Clad Vent Set cups that protect the radioactive fuel in radioisotope thermoelectric generators (RTGs) which provide electric power for spacecraft and rovers. In a previous study, the tensile properties of DOP-26 were measured over a wide range of strain rates and temperatures and reported in ORNL/TM-2007/81. While that study established the properties of the base material, the fabrication of the heat sources requires welding, and the mechanical properties of welded DOP-26 have not been extensively characterized in the past. Therefore, this study was undertaken to determine the mechanical properties of DOP-26 specimens containing a transverse weld in the center of their gage sections. Tensile tests were performed at room temperature, 750, 900, and 1090°C and engineering strain rates of 1×10^-3 and 10 s^-1. Room temperature testing was performed in air, while testing at elevated temperatures was performed in a vacuum better than 1×10^-4 Torr. The welded specimens had a significantly higher yield stress, by up to a factor of ~2, than the non-welded base material. The yield stress did not depend on the strain rate except at 1090°C, where it was slightly higher for the faster strain rate. The ultimate tensile stress, on the other hand, was significantly higher for the faster strain rate at temperatures of 750°C and above. At 750°C and above, the specimens deformed at 1×10^-3 s^-1 showed pronounced necking resulting sometimes in perfect chisel-edge fracture. The specimens deformed at 10 s^-1 exhibited this fracture behavior only at the highest test temperature, 1090°C. Fracture occurred usually in the fusion zone of the weld and was, in most cases, primarily intergranular.

Variation of strain rate sensitivity index of a superplastic aluminum alloy in different testing methods

Science.gov (United States)

Majidi, Omid; Jahazi, Mohammad; Bombardier, Nicolas; Samuel, Ehab

2017-10-01

The strain rate sensitivity index, m-value, is being applied as a common tool to evaluate the impact of the strain rate on the viscoplastic behaviour of materials. The m-value, as a constant number, has been frequently taken into consideration for modeling material behaviour in the numerical simulation of superplastic forming processes. However, the impact of the testing variables on the measured m-values has not been investigated comprehensively. In this study, the m-value for a superplastic grade of an aluminum alloy (i.e., AA5083) has been investigated. The conditions and the parameters that influence the strain rate sensitivity for the material are compared with three different testing methods, i.e., monotonic uniaxial tension test, strain rate jump test and stress relaxation test. All tests were conducted at elevated temperature (470°C) and at strain rates up to 0.1 s-1. The results show that the m-value is not constant and is highly dependent on the applied strain rate, strain level and testing method.

Limit strains for severe accident conditions. Final report of the EU-project LISSAC

International Nuclear Information System (INIS)

Krieg, R.; Seidenfuss, M.

2003-10-01

The local failure strains of essential reactor vessel components are investigated. The size influence of the components is of special interest. Typical severe accident conditions including elevated temperatures and dynamic loads are considered. The main part of work consists of test families with specimens under uniaxial and biaxial static and dynamic loads. Within one test family the specimen geometries and the load conditions are similar, the temperature is the same; but the size is varied up to reactor dimensions. Special attention is given to geometries with a hole or a notch causing non-uniform stress and strain distributions typical for reactor components. There are indications that for such non-uniform distributions size effects may be stronger than for uniform distributions. Thus size effects on the failure strains and failure processes are determined under realistic conditions. Several tests with nominal identical parameters are performed for small size specimens. In this way some information is obtained about the scatter. A reduced number of tests is carried out for medium size specimens and only a few tests are carried out for large size specimens to reduce the costs to an acceptable level. To manufacture all specimens sufficient material was available from the unused reactor pressure vessel Biblis C consisting of the material 22NiMoCr37. Thus variations of the mechanical material properties, which could impair the interpretation of the test results, are quite small. This has been confirmed by an adequate number of additional quality assurance tests. A key problem was the definition of failure and the determination of the local strains at failure for very different specimens under varying load conditions. Here appropriate methods had to be developed including the so-called 'vanishing gap method' and the 'forging die method'. They are based on post test geometrical measurements of the fracture surfaces and reconstructions of the related strain fields

Pile Model Tests Using Strain Gauge Technology

Science.gov (United States)

Krasiński, Adam; Kusio, Tomasz

2015-09-01

Ordinary pile bearing capacity tests are usually carried out to determine the relationship between load and displacement of pile head. The measurement system required in such tests consists of force transducer and three or four displacement gauges. The whole system is installed at the pile head above the ground level. This approach, however, does not give us complete information about the pile-soil interaction. We can only determine the total bearing capacity of the pile, without the knowledge of its distribution into the shaft and base resistances. Much more information can be obtained by carrying out a test of instrumented pile equipped with a system for measuring the distribution of axial force along its core. In the case of pile model tests the use of such measurement is difficult due to small scale of the model. To find a suitable solution for axial force measurement, which could be applied to small scale model piles, we had to take into account the following requirements: - a linear and stable relationship between measured and physical values, - the force measurement accuracy of about 0.1 kN, - the range of measured forces up to 30 kN, - resistance of measuring gauges against aggressive counteraction of concrete mortar and against moisture, - insensitivity to pile bending, - economical factor. These requirements can be fulfilled by strain gauge sensors if an appropriate methodology is used for test preparation (Hoffmann [1]). In this paper, we focus on some aspects of the application of strain gauge sensors for model pile tests. The efficiency of the method is proved on the examples of static load tests carried out on SDP model piles acting as single piles and in a group.

Dynamic Brazilian Test of Rock Under Intermediate Strain Rate: Pendulum Hammer-Driven SHPB Test and Numerical Simulation

Science.gov (United States)

Zhu, W. C.; Niu, L. L.; Li, S. H.; Xu, Z. H.

2015-09-01

The tensile strength of rock subjected to dynamic loading constitutes many engineering applications such as rock drilling and blasting. The dynamic Brazilian test of rock specimens was conducted with the split Hopkinson pressure bar (SHPB) driven by pendulum hammer, in order to determine the indirect tensile strength of rock under an intermediate strain rate ranging from 5.2 to 12.9 s-1, which is achieved when the incident bar is impacted by pendulum hammer with different velocities. The incident wave excited by pendulum hammer is triangular in shape, featuring a long rising time, and it is considered to be helpful for achieving a constant strain rate in the rock specimen. The dynamic indirect tensile strength of rock increases with strain rate. Then, the numerical simulator RFPA-Dynamics, a well-recognized software for simulating the rock failure under dynamic loading, is validated by reproducing the Brazilian test of rock when the incident stress wave retrieved at the incident bar is input as the boundary condition, and then it is employed to study the Brazilian test of rock under the higher strain rate. Based on the numerical simulation, the strain-rate dependency of tensile strength and failure pattern of the Brazilian disc specimen under the intermediate strain rate are numerically simulated, and the associated failure mechanism is clarified. It is deemed that the material heterogeneity should be a reason for the strain-rate dependency of rock.

A proposed standard round compact specimen for plane strain fracture toughness testing

Science.gov (United States)

Underwood, J. H.; Newman, J. C., Jr.; Seeley, R. R.

1980-01-01

A round, disk-shaped specimen is proposed as a standard test specimen for addition to ASTM Test for Plane-Strain Fracture Toughness of Metallic Materials (E 399-78A). The specimen is diametrically cracked, and loaded in the same way as the existing standard compact specimen. Tests and analyses were performed to verify that the proposed round compact specimen and associated stress intensity factor K solution are appropriate for a standard plane strain fracture toughness test. The use of the round compact specimen for other fracture tests is described.

Design of triaxial test with controlled suction: measure of strain

International Nuclear Information System (INIS)

Gasc-Barbier, M.; Cosenza, Ph.; Ghoreychi, M.; Chanchole, S.; Cosenza, Ph.; Tessier, D.

2000-01-01

Experimental study of mechanical behavior of clayey materials under hygrometric condition is usually performed either on unloaded samples or by means of classical odometer tests used in soil mechanics. Such methods are not well adapted to hard deep clayey rocks with little deformability, porosity and permeability. Moreover, stress and strain tensors having a significant effect on hygro-mechanical behaviour and properties cannot be measured and investigated appropriately by classical tests. This is why a specific triaxial test was designed in which the sample is surrounded by a fiber glass tissue allowing air circulation and then by silicon on which confining pressure is applied. Thus, equilibrium between air and sample was reduced. Stress and strain tensors were also measured in time on the sample subjected to a mechanical loading and to a controlled suction. After presentation of the test, preliminary results are given. (authors)

Comparisons of Venezuelan encephalitis virus strains by hemagglutination-inhibition tests with chicken antibodies.

Science.gov (United States)

Scherer, W F; Pancake, B A

1977-01-01

Twenty strains of Venezuelan encephalitis (VE) virus inoculated intravenously in large doses into roosters produced hemagglutination-inhibition (HI) antibodies detectable in plasmas within 7 to 10 days. No signs of illness occurred, and there was no evidence of viral growth in tissues since blood concentrations of infectious virus steadily decreased after inoculation. HI antibodies in early plasmas were specific for VE virus and did not cross-react significantly with two other North American alphaviruses, eastern and western encephalitis viruses. VE virus strains could be distinquished by virus-dilution, short-incubation HI, but not by plasma-dilution neutralization tests, by using early rooster antibodies. The distinctions by HI test were similar with some strains to, but different with other strains from, those described by Young and Johnson with the spiny rat antisera used to establish their subtype classifications of VE virus (14, 28). Nevertheless, results of HI tests with rooster antibodies correlated with equine virulence, as did results with spiny rat antibodies, and distinguished the new strains of virus that appeared in Middle America during the VE outbreak of 1969 from preexisting strains. PMID:591629

The final focus test beam project

International Nuclear Information System (INIS)

Burke, D.

1991-05-01

An overview is given of the Final Focus Test Beam (FFTB) that is being constructed as a prototype final focus system for a future electron-positron linear collider. This beam line will use as input the 50 GeV electron beam from the SLC linac, and is designed to reduce the transverse dimensions of the beam spot at the focal point to 1 μm. 5 refs., 2 figs., 1 tab

Cyclic mechanical behavior of 316L: Uniaxial LCF and strain-controlled ratcheting tests

International Nuclear Information System (INIS)

Facheris, G.; Janssens, K.G.F.

2013-01-01

Highlights: ► Characterization of cyclic plastic deformation behavior of plate and tubular 316L. ► Strain-controlled ratcheting response between room temperature and 200 °C. ► Isotropic cyclic hardening is dependent on the yield criterion used. ► Ratcheting induced hardening mostly affects the kinematic hardening component. ► Ratcheting induced hardening is related to the mean strain and the ratcheting rate. -- Abstract: With the purpose of analyzing the fatigue behavior under loading conditions relevant for the primary cooling circuit of a light water nuclear reactor, a set of uniaxial low cycle fatigue and strain-controlled ratcheting tests (also named ‘cyclic tension tests’) has been performed at room temperature and at 200 °C on specimens manufactured from two different batches of stainless steel grade 316L. The experiments have been repeated varying strain amplitude, cyclic ratcheting rate and ratcheting direction in order to investigate the influence on the cyclic deformation behavior. In strain-controlled ratcheting tests, the stress response is found to be a superposition of two hardening mechanisms: the first one due to the zero mean strain cycling and the second one linked with the monotonic drifting of mean plastic strain. An approach is proposed to distinguish the effect of each mechanism and the influence of the test parameters on the hardening mechanisms is discussed

Flat-Cladding Fiber Bragg Grating Sensors for Large Strain Amplitude Fatigue Tests

Directory of Open Access Journals (Sweden)

Xijia Gu

2010-08-01

Full Text Available We have successfully developed a flat-cladding fiber Bragg grating sensor for large cyclic strain amplitude tests of up to ±8,000 με. The increased contact area between the flat-cladding fiber and substrate, together with the application of a new bonding process, has significantly increased the bonding strength. In the push-pull fatigue tests of an aluminum alloy, the plastic strain amplitudes measured by three optical fiber sensors differ only by 0.43% at a cyclic strain amplitude of ±7,000 με and 1.9% at a cyclic strain amplitude of ±8,000 με. We also applied the sensor on an extruded magnesium alloy for evaluating the peculiar asymmetric hysteresis loops. The results obtained were in good agreement with those measured from the extensometer, a further validation of the sensor.

Strain measurement in and analysis for hydraulic test of CPR1000 reactor pressure vessel

International Nuclear Information System (INIS)

Zhou Dan; Zhuang Dongzhen

2013-01-01

The strain measurement in hydraulic test of CPR1000 reactor pressure vessel performed in Dongfang Heavy Machinery Co., Ltd. is introduced. The detail test scheme and method was introduced and the measurement results of strain and stress was given. Meanwhile the finite element analysis was performed for the pressure vessel, which was generally matched with the measurement results. The reliability of strain measurement was verified and the high strength margin of vessel was shown, which would give a good reference value for the follow-up hydraulic tests and strength analysis of reactor pressure vessel. (authors)

FEBEX II Project Final report on thermo-hydro-mechanical laboratory tests

International Nuclear Information System (INIS)

Lloret, A.; Romero, E.; Villar, M. V.

2004-01-01

strains of clay upon saturation with different kinds of water (deionised, granitic and saline with different salts and concentrations) were measured as a function of initial dry density and overload. The effects of salinity on bentonite stiffness and permeability were also investigated. The swelling capacity of clay, saturated with highly saline water, reduces drastically, osmotic consolidation being even observed. The swelling strains measured when the samples were soaked with different saline concentrations are similar to the strains measured in suction controlled odometer tests, in which it is applied a final suction equal to the osmotic suction of the saline solutions. The hydraulic conductivity of bentonite increases with saline concentration of the permeant, especially in the case of low densities. The infiltration tests have shown that the gas permeability of dry bentonite is very high. The water intake is higher for the sample tested under room temperature, since the hot zones of the sample tested under thermal gradient remain desiccated for a long time. It has been proven that the combination of infiltration tests and coupled THMC numerical analysis can help to a better understanding of the FEBEX bentonite behaviour under repository conditions. In summary, the behaviour of the clay may be mostly explained taking into account its double structure. The interactions between the two structural levels are responsible of the main features of the mechanical aspects of this behaviour. A deeper insight of the behaviour of compacted bentonite, and of the basic mechanisms controlling it, has been achieved using an elasto-plastic framework that incorporates the interplay between microstructural and macrostructural fabric levels in a simplified manner. On the other hand, temperature induced transfers between intraaggregate adsorbed water of density higher than that of free water and inter-aggregate free water could explain most of the features related with the temperature

FEBEX II Project Final report on thermo-hydro-mechanical laboratory tests

Energy Technology Data Exchange (ETDEWEB)

Lloret, A.; Romero, E.; Villar, M. V.

2004-07-01

strains of clay upon saturation with different kinds of water (deionised, granitic and saline with different salts and concentrations) were measured as a function of initial dry density and overload. The effects of salinity on bentonite stiffness and permeability were also investigated. The swelling capacity of clay, saturated with highly saline water, reduces drastically, osmotic consolidation being even observed. The swelling strains measured when the samples were soaked with different saline concentrations are similar to the strains measured in suction controlled odometer tests, in which it is applied a final suction equal to the osmotic suction of the saline solutions. The hydraulic conductivity of bentonite increases with saline concentration of the permeant, especially in the case of low densities. The infiltration tests have shown that the gas permeability of dry bentonite is very high. The water intake is higher for the sample tested under room temperature, since the hot zones of the sample tested under thermal gradient remain desiccated for a long time. It has been proven that the combination of infiltration tests and coupled THMC numerical analysis can help to a better understanding of the FEBEX bentonite behaviour under repository conditions. In summary, the behaviour of the clay may be mostly explained taking into account its double structure. The interactions between the two structural levels are responsible of the main features of the mechanical aspects of this behaviour. A deeper insight of the behaviour of compacted bentonite, and of the basic mechanisms controlling it, has been achieved using an elasto-plastic framework that incorporates the interplay between microstructural and macrostructural fabric levels in a simplified manner. On the other hand, temperature induced transfers between intraaggregate adsorbed water of density higher than that of free water and inter-aggregate free water could explain most of the features related with the temperature

Characterization of strain rate sensitivity and activation volume using the indentation relaxation test

International Nuclear Information System (INIS)

Xu Baoxing; Chen Xi; Yue Zhufeng

2010-01-01

We present the possibility of extracting the strain rate sensitivity, activation volume and Helmholtz free energy (for dislocation activation) using just one indentation stress relaxation test, and the approach is demonstrated with polycrystalline copper. The Helmholtz free energy measured from indentation relaxation agrees well with that from the conventional compression relaxation test, which validates the proposed approach. From the indentation relaxation test, the measured indentation strain rate sensitivity exponent is found to be slightly larger, and the indentation activation volume much smaller, than their counterparts from the compression test. The results indicate the involvement of multiple dislocation mechanisms in the indentation test.

Behavioural analysis of four mouse strains in an anxiety test battery.

Science.gov (United States)

van Gaalen, M M; Steckler, T

2000-10-01

Differences in locomotor activity, exploratory activity and anxiety-like behaviour of C57BL/6ChR,C57BL/6J, Swiss Webster/J and A/J strain were investigated in an anxiety battery. The battery consisted of paradigms studying spontaneous behaviour after a mild stressor, tasks of innate anxiety (light-dark box, elevated plus maze, novel object exploration), response to a conflict situation (Vogel conflict), conditioned fear and response to inescapable swim stress. Locomotor activity was studied in an open field and compared with locomotion in the other tests. Exploratory behaviour was studied in a 16-hole board task. The data confirm previous studies suggesting that A/J mice are a relatively anxious strain. Also, the data indicated that locomotor activity was independent of the paradigm employed, while the rank order of strain-dependent effects on anxiety-related behaviour changed as a function of the task under study. Our data provide further support for the notion that choice of strain is essential in studies of anxiety-related behaviour. Influence of strain should be considered in pharmacological and lesion studies, as well as in studies with mutant mice. In addition, the data indicate that different anxiety paradigms tax different aspects of anxiety, suggesting that a battery of different tests should be used in studies of anxiety-related behaviour.

Predicting creep rupture from early strain data

International Nuclear Information System (INIS)

Holmstroem, Stefan; Auerkari, Pertti

2009-01-01

To extend creep life modelling from classical rupture modelling, a robust and effective parametric strain model has been developed. The model can reproduce with good accuracy all parts of the creep curve, economically utilising the available rupture models. The resulting combined model can also be used to predict rupture from the available strain data, and to further improve the rupture models. The methodology can utilise unfailed specimen data for life assessment at lower stress levels than what is possible from rupture data alone. Master curves for creep strain and rupture have been produced for oxygen-free phosphorus-doped (OFP) copper with a maximum testing time of 51,000 h. Values of time to specific strain at given stress (40-165 MPa) and temperature (125-350 deg. C) were fitted to the models in the strain range of 0.1-38%. With typical inhomogeneous multi-batch creep data, the combined strain and rupture modelling involves the steps of investigation of the data quality, extraction of elastic and creep strain response, rupture modelling, data set balancing and creep strain modelling. Finally, the master curves for strain and rupture are tested and validated for overall fitting efficiency. With the Wilshire equation as the basis for the rupture model, the strain model applies classical parametric principles with an Arrhenius type of thermal activation and a power law type of stress dependence for the strain rate. The strain model also assumes that the processes of primary and secondary creep can be reasonably correlated. The rupture model represents a clear improvement over previous models in the range of the test data. The creep strain information from interrupted and running tests were assessed together with the rupture data investigating the possibility of rupture model improvement towards lower stress levels by inverse utilisation of the combined rupture based strain model. The developed creep strain model together with the improved rupture model is

Sensitivity of the polypropylene to the strain rate: experiments and modeling

International Nuclear Information System (INIS)

Abdul-Latif, A.; Aboura, Z.; Mosleh, L.

2002-01-01

Full text.The main goal of this work is first to evaluate experimentally the strain rate dependent deformation of the polypropylene under tensile load; and secondly is to propose a model capable to appropriately describe the mechanical behavior of this material and especially its sensitivity to the strain rate. Several experimental tensile tests are performed at different quasi-static strain rates in the range of 10 -5 s -1 to 10 -1 s -1 . In addition to some relaxation tests are also conducted introducing the strain rate jumping state during testing. Within the framework of elastoviscoplasticity, a phenomenological model is developed for describing the non-linear mechanical behavior of the material under uniaxial loading paths. With the small strain assumption, the sensitivity of the polypropylene to the strain rate being of particular interest in this work, is accordingly taken into account. As a matter of fact, since this model is based on internal state variables, we assume thus that the material sensitivity to the strain rate is governed by the kinematic hardening variable notably its modulus and the accumulated viscoplastic strain. As far as the elastic behavior is concerned, it is noticed that such a behavior is slightly influenced by the employed strain rate rage. For this reason, the elastic behavior is classically determined, i.e. without coupling with the strain rate dependent deformation. It is obvious that the inelastic behavior of the used material is thoroughly dictated by the applied strain rate. Hence, the model parameters are well calibrated utilizing several experimental databases for different strain rates (10 -5 s -1 to 10 -1 s -1 ). Actually, among these experimental results, some experiments related to the relaxation phenomenon and strain rate jumping during testing (increasing or decreasing) are also used in order to more perfect the model parameters identification. To validate the calibrated model parameters, simulation tests are achieved

Tensile strength of concrete under static and intermediate strain rates: Correlated results from different testing methods

International Nuclear Information System (INIS)

Wu Shengxing; Chen Xudong; Zhou Jikai

2012-01-01

Highlights: ► Tensile strength of concrete increases with increase in strain rate. ► Strain rate sensitivity of tensile strength of concrete depends on test method. ► High stressed volume method can correlate results from various test methods. - Abstract: This paper presents a comparative experiment and analysis of three different methods (direct tension, splitting tension and four-point loading flexural tests) for determination of the tensile strength of concrete under low and intermediate strain rates. In addition, the objective of this investigation is to analyze the suitability of the high stressed volume approach and Weibull effective volume method to the correlation of the results of different tensile tests of concrete. The test results show that the strain rate sensitivity of tensile strength depends on the type of test, splitting tensile strength of concrete is more sensitive to an increase in the strain rate than flexural and direct tensile strength. The high stressed volume method could be used to obtain a tensile strength value of concrete, free from the influence of the characteristics of tests and specimens. However, the Weibull effective volume method is an inadequate method for describing failure of concrete specimens determined by different testing methods.

Breeding study of hyper citric acid strain by progressive heavy ion irradiation

International Nuclear Information System (INIS)

Chen Jihong; Hu Wei; Li Wenjian; Liu Jing; Wang Shuyang; Wei Zihao

2013-01-01

Heavy "1"2C"6"+ ion beams in various high doses were employed to irradiate H3001 strain for screening Aspergillus niger strain for hyper citric acid production. Three high-yield strains were obtained after shaker fermentation test. Among the three strains, the strain hw317 was implemented shaker fermentation for stability test and 10∼100 L pilot fermentation tank for citric acid productive maximization. Acid-base neutralization method was applied to determinate the content of citric acid in fermented liquid. The results showed that: when the secondary heavy ion "1"2C"6"+ dose was 857.8 Gy, both of the fatality rate (94.5%) and the positive mutation rate (8%) were highest. Through the shaker fermentation tests and 10∼100 L pilot fermentation test, one strain hw317 was screened and obtained for hyper citric acid production. Consequently, the final citric acid acidity can reach up to 19.2±0.2% with controlling fermentation cycle for 60 h. (authors)

Simple test of synergy between ampicillin and vancomycin for resistant strains of Enterococcus faecium.

OpenAIRE

Green, M; Barbadora, K; Wadowsky, R M

1994-01-01

The combination of ampicillin and vancomycin kills some but not all strains of ampicillin- and vancomycin-resistant Enterococcus faecium. We compared a simple test for synergy utilizing a commercially available microdilution susceptibility system with time-kill studies and determined acceptable breakpoints for this test for 20 strains of ampicillin- and vancomycin-resistant E. faecium. The combination of ampicillin and vancomycin was tested for synergy by time-kill, broth macrodilution, and b...

Processing of plane strain compression test results for investigation of AISI-304 stainless steel constitutive behavior

International Nuclear Information System (INIS)

Aksenov, Sergey A.; Puzino, Yuriy A.; Bober, Stanislav A.; Kliber, Jiri

2015-01-01

The paper is oriented toward the determination of constitutive equation constants by the inverse analysis of plane strain compression test results. The interpretation of such results is complicated by the inhomogeneity of strain rate distribution in the specimen caused by rigid ends, the lateral spreading of a specimen friction and the variation of temperature during the test. The results of plane strain compression tests of AISI-304 stainless steel are presented and significant deviations of temperature are observed at higher strain rates. Finite element simulation was performed to estimate the inhomogeneity of strain rate within the specimen and evaluate the effect of friction on the test results. Constitutive equations of the material were obtained by inverse analysis minimizing the deviations between the measured load values and the ones predicted by numerical simulation. Keywords: PSCT, AISI-304, Gleeble, constitutive equations, hot forming, FEM, inverse analysis.

Field monitoring of static, dynamic, and statnamic pile loading tests using fibre Bragg grating strain sensors

Science.gov (United States)

Li, Jin; Correia, Ricardo P.; Chehura, Edmon; Staines, Stephen; James, Stephen W.; Tatam, Ralph; Butcher, Antony P.; Fuentes, Raul

2009-10-01

Pile loading test plays an important role in the field of piling engineering. In order to gain further insight into the load transfer mechanism, strain gauges are often used to measure local strains along the piles. This paper reports a case whereby FBG strain sensors was employed in a field trial conducted on three different types of pile loading tests in a glacial till. The instrumentation systems were configured to suit the specific characteristic of each type of test. Typical test results are presented. The great potential of using FBG sensors for pile testing is shown.

A fiber optic strain measurement and quench localization for use in superconducting accelerator dipole magnets

International Nuclear Information System (INIS)

van Oort, J.M.; Scanlan, R.M.; ten Kate, H.H.J.

1994-01-01

A novel fiber-optic measurement system for superconducting accelerator magnets is described. The principal component is an extrinsic Fabry-Perot Interferometer to determine localized strain and stress in coil windings. The system can be used either as a sensitive relative strain measurement system or as an absolute strain detector. Combined, one can monitor the mechanical behaviour of the magnet system over time during construction, long time storage and operation. The sensing mechanism is described, together with various tests in laboratory environments. The test results of a multichannel test matrix to be incorporated first in the dummy coils and then in the final version of a 13T Nb 3 Sn accelerator dipole magnet are presented. Finally, the possible use of this system as a quench localization system is proposed

Combination of poroelasticity theory and constant strain rate test in modelling land subsidence due to groundwater extraction

Science.gov (United States)

Pham, Tien Hung; Rühaak, Wolfram; Sass, Ingo

2017-04-01

Extensive groundwater extraction leads to a drawdown of the ground water table. Consequently, soil effective stress increases and can cause land subsidence. Analysis of land subsidence generally requires a numerical model based on poroelasticity theory, which was first proposed by Biot (1941). In the review of regional land subsidence accompanying groundwater extraction, Galloway and Burbey (2011) stated that more research and application is needed in coupling of stress-dependent land subsidence process. In geotechnical field, the constant rate of strain tests (CRS) was first introduced in 1969 (Smith and Wahls 1969) and was standardized in 1982 through the designation D4186-82 by American Society for Testing and Materials. From the reading values of CRS tests, the stress-dependent parameters of poroelasticity model can be calculated. So far, there is no research to link poroelasticity theory with CRS tests in modelling land subsidence due to groundwater extraction. One dimensional CRS tests using conventional compression cell and three dimension CRS tests using Rowe cell were performed. The tests were also modelled by using finite element method with mixed elements. Back analysis technique is used to find the suitable values of hydraulic conductivity and bulk modulus that depend on the stress or void ratio. Finally, the obtained results are used in land subsidence models. Biot, M. A. (1941). "General theory of three-dimensional consolidation." Journal of applied physics 12(2): 155-164. Galloway, D. L. and T. J. Burbey (2011). "Review: Regional land subsidence accompanying groundwater extraction." Hydrogeology Journal 19(8): 1459-1486. Smith, R. E. and H. E. Wahls (1969). "Consolidation under constant rates of strain." Journal of Soil Mechanics & Foundations Div.

Three-axial strain controlled testing applied to bone specimens from the proximal tibial epiphysis

DEFF Research Database (Denmark)

Linde, F.; Pongsoipetch, B.; Frich, Lars Henrik

1990-01-01

Reproducibility of the determination of Young's modulus and energy absorption along the three axes of trabecular bone cubes was analysed by non-destructive compression to 0.5% strain using different testing protocols. These protocols included testing with and without pre-conditioning to a viscoel......Reproducibility of the determination of Young's modulus and energy absorption along the three axes of trabecular bone cubes was analysed by non-destructive compression to 0.5% strain using different testing protocols. These protocols included testing with and without pre...

High strain fatigue behaviour of a high-temperature, low-alloyed forging steel subject to a servicelike loading history

International Nuclear Information System (INIS)

Kloos, K.H.; Granacher, J.; Rieth, P.

1979-01-01

A test plan was developed for selected cases of service-like long-time high strain load of a heated surface of massive components, which includes service-like anisothermic high strain tests with pressure-strain in the start-up phase and pull-strain in the shutdown phase, comparable isothermal tests at the highest cycle temperature, and finally tests with 'packaged' high strain and creep strain periods, which should enable long-time-tests with only short use of the large-scale high-strain-test-technique. The tests started on the melts of the high-temperature steel 28 Cr Mo NiV 4 9 have reached a longest tests time of nearly 1000 at a maximum temperature of 525 0 C. On the basis of there results, the carrying-out of 'packaged' long-time high strain tests with short creep strain periods seem to be a good way of determining the long-time high-strain behaviour of this steel under service-like strain cycles. (orig./RW) 891 RW/orig.- 892 RKD [de

Method for independent strain and temperature measurement in polymeric tensile test specimen using embedded FBG sensors

DEFF Research Database (Denmark)

Pereira, Gilmar Ferreira; McGugan, Malcolm; Mikkelsen, Lars Pilgaard

2016-01-01

to calculate independently the strain and temperature are presented in the article, together with a measurement resolution study. This multi-parameter measurement method was applied to an epoxy tensile specimen, tested in a unidirectional tensile test machine with a temperature controlled cabinet. A full......A novel method to obtain independent strain and temperature measurements using embedded Fibre Bragg Grating (FBG) in polymeric tensile test specimens is presented in this paper. The FBG strain and temperature cross-sensitivity was decoupled using two single mode FBG sensors, which were embedded...... of temperature, from 40 C to -10 C. The consistency of the expected theoretical results with the calibration procedure and the experimental validation shows that this proposed method is applicable to measure accurate strain and temperature in polymers during static or fatigue tensile testing. Two different...

Normalized Rotational Multiple Yield Surface Framework (NRMYSF) stress-strain curve prediction method based on small strain triaxial test data on undisturbed Auckland residual clay soils

Science.gov (United States)

Noor, M. J. Md; Ibrahim, A.; Rahman, A. S. A.

2018-04-01

Small strain triaxial test measurement is considered to be significantly accurate compared to the external strain measurement using conventional method due to systematic errors normally associated with the test. Three submersible miniature linear variable differential transducer (LVDT) mounted on yokes which clamped directly onto the soil sample at equally 120° from the others. The device setup using 0.4 N resolution load cell and 16 bit AD converter was capable of consistently resolving displacement of less than 1µm and measuring axial strains ranging from less than 0.001% to 2.5%. Further analysis of small strain local measurement data was performed using new Normalized Multiple Yield Surface Framework (NRMYSF) method and compared with existing Rotational Multiple Yield Surface Framework (RMYSF) prediction method. The prediction of shear strength based on combined intrinsic curvilinear shear strength envelope using small strain triaxial test data confirmed the significant improvement and reliability of the measurement and analysis methods. Moreover, the NRMYSF method shows an excellent data prediction and significant improvement toward more reliable prediction of soil strength that can reduce the cost and time of experimental laboratory test.

Triaxial extensometer for volumetric strain measurement in a hydro-compression loading test for foam materials

International Nuclear Information System (INIS)

Feng, Bo; Xu, Ming-long; Zhao, Tian-fei; Zhang, Zhi-jun; Lu, Tian-jian

2010-01-01

A new strain gauge-based triaxial extensometer (radial extensometers x, y and axial extensometer z) is presented to improve the volumetric strain measurement in a hydro-compression loading test for foam materials. By the triaxial extensometer, triaxial deformations of the foam specimen can be measured directly, from which the volumetric strain is determined. Sensitivities of the triaxial extensometer are predicted using a finite-element model, and verified through experimental calibrations. The axial extensometer is validated by conducting a uniaxial compression test in aluminium foam and comparing deformation measured by the axial extensometer to that by the advanced optical 3D deformation analysis system ARAMIS; the result from the axial extensometer agrees well with that from ARAMIS. A new modus of two-wire measurement and transmission in a hydrostatic environment is developed to avoid the punching and lead sealing techniques on the pressure vessel for the hydro-compression test. The effect of hydrostatic pressure on the triaxial extensometer is determined through an experimental test. An application in an aluminium foam hydrostatic compression test shows that the triaxial extensometer is effective for volumetric strain measurement in a hydro-compression loading test for foam materials

Antibiotic susceptibility profiles of some Vibrio strains isolated from wastewater final effluents in a rural community of the Eastern Cape Province of South Africa

Directory of Open Access Journals (Sweden)

Igbinosa Etinosa O

2010-05-01

Full Text Available Abstract Background To evaluate the antibiogram and antibiotic resistance genes of some Vibrio strains isolated from wastewater final effluents in a rural community of South Africa. V. vulnificus (18, V. metschnikovii (3, V. fluvialis (19 and V. parahaemolyticus (12 strains were isolated from final effluents of a wastewater treatment plant (WWTP located in a rural community of South Africa. The disk diffusion method was used for the characterization of the antibiogram of the isolates. Polymerase chain reaction (PCR was employed to evaluate the presence of established antibiotic resistance genes using specific primer sets. Results The Vibrio strains showed the typical multidrug-resistance phenotype of an SXT element. They were resistant to sulfamethoxazole (Sul, trimethoprim (Tmp, cotrimoxazole (Cot, chloramphenicol (Chl, streptomycin (Str, ampicillin (Amp, tetracycline (Tet nalidixic acid (Nal, and gentamicin (Gen. The antibiotic resistance genes detected includes dfr18 and dfrA1 for trimethoprim; floR, tetA, strB, sul2 for chloramphenicol, tetracycline, streptomycin and sulfamethoxazole respectively. Some of these genes were only recently described from clinical isolates, demonstrating genetic exchange between clinical and environmental Vibrio species. Conclusions These results demonstrate that final effluents from wastewater treatment plants are potential reservoirs of various antibiotics resistance genes. Moreover, detection of resistance genes in Vibrio strains obtained from the wastewater final effluents suggests that these resistance determinants might be further disseminated in habitats downstream of the sewage plant, thus constituting a serious health risk to the communities reliant on the receiving waterbodies.

Serotyping of Actinobacillus pleuropneumoniae serotype 5 strains using a monoclonal-based polystyrene agglutination test

DEFF Research Database (Denmark)

Dubreuil, J.D.; Letellier, A.; Stenbæk, Eva

1996-01-01

A polystyrene agglutination test has been developed for serotyping Actinobacillus pleuropneumoniae serotype 5a and 5b strains. Protein A-coated polystyrene microparticles were sensitized with a murine monoclonal antibody recognizing an epitope on serotype 5 LPS-O chain as shown by SDS-PAGE and We......A polystyrene agglutination test has been developed for serotyping Actinobacillus pleuropneumoniae serotype 5a and 5b strains. Protein A-coated polystyrene microparticles were sensitized with a murine monoclonal antibody recognizing an epitope on serotype 5 LPS-O chain as shown by SDS...... suspension of bacterial cells grown for 18 h. All A, pleuropneumoniae strains had been previously serotyped using standard procedures, The polystyrene agglutination test was rapid (less than 3 min) and easy to perform. Overall a very good correlation (97.3%) with the standard techniques was found...

Longitudinally Jointed Edge-wise Compression Honeycomb Composite Sandwich Coupon Testing and FE Analysis: Three Methods of Strain Measurement, and Comparison

Science.gov (United States)

Farrokh, Babak; AbdulRahim, Nur Aida; Segal, Ken; Fan, Terry; Jones, Justin; Hodges, Ken; Mashni, Noah; Garg, Naman; Sang, Alex; Gifford, Dawn;

Relationship between strain and central deflection in small punch creep specimens

International Nuclear Information System (INIS)

Yang Zhen; Wang Zhiwen

2003-01-01

Acquiring information about creep strain directly from small punch creep tests is difficult because the deformation behaviour of the small punch specimen is complicated. A routine is suggested in the present paper to treat this problem indirectly. Based on a finite element analysis, it is proposed that the relationship of central deflection δ to central creep strain ε c of a specimen subjected to creep can be represented approximately by the relationship of central deflection δ to central (elastic-plastic) strain ε of a specimen not subjected to creep. With this hypothesis, the δ∼ε c relation of the small punch creep specimen is obtained by resorting to a rigid-plastic membrane stretch forming model. Finally, small punch creep test results are used to evaluate creep strain and creep strain rate by taking advantage of this δ∼ε c relation

Strain transfer through film-substrate interface and surface curvature evolution during a tensile test

Science.gov (United States)

He, Wei; Han, Meidong; Goudeau, Philippe; Bourhis, Eric Le; Renault, Pierre-Olivier; Wang, Shibin; Li, Lin-an

2018-03-01

Uniaxial tensile tests on polyimide-supported thin metal films are performed to respectively study the macroscopic strain transfer through an interface and the surface curvature evolution. With a dual digital image correlation (DIC) system, the strains of the film and the substrate can be simultaneously measured in situ during the tensile test. For the true strains below 2% (far beyond the films' elastic limit), a complete longitudinal strain transfer is present irrespective of the film thickness, residual stresses and microstructure. By means of an optical surface profiler, the three-dimensional (3D) topography of film surface can be obtained during straining. As expected, the profile of the specimen center remains almost flat in the tensile direction. Nevertheless, a relatively significant curvature evolution (of the same order with the initial curvature induced by residual stresses) is observed along the transverse direction as a result of a Poisson's ratio mismatch between the film and the substrate. Furthermore, finite element method (FEM) has been performed to simulate the curvature evolution considering the geometric nonlinearity and the perfect strain transfer at the interface, which agrees well with the experimental results.

Relationship between the Pedaling Biomechanics and Strain of Bicycle Frame during Submaximal Tests

OpenAIRE

Manolova, Aneliya; Crequy, Samuel; Lestriez, Philippe; Debraux, Pierre; Bertucci, William

2015-01-01

The aim of this study was to analyse the effect of forces applied to pedals and cranks on the strain imposed to an instrumented bicycle motocross (BMX) frame. Using results from a finite element analysis to determine the localisation of highest stress, eight strain gauges were located on the down tube, the seat tube and the right chain stay. Before the pedaling tests, static loads were applied to the frame during bench tests. Two pedaling conditions have been analysed. In the first, the rider...

Sequencing of bovine herpesvirus 4 v.test strain reveals important genome features

Directory of Open Access Journals (Sweden)

Gillet Laurent

2011-08-01

Full Text Available Abstract Background Bovine herpesvirus 4 (BoHV-4 is a useful model for the human pathogenic gammaherpesviruses Epstein-Barr virus and Kaposi's Sarcoma-associated Herpesvirus. Although genome manipulations of this virus have been greatly facilitated by the cloning of the BoHV-4 V.test strain as a Bacterial Artificial Chromosome (BAC, the lack of a complete genome sequence for this strain limits its experimental use. Methods In this study, we have determined the complete sequence of BoHV-4 V.test strain by a pyrosequencing approach. Results The long unique coding region (LUR consists of 108,241 bp encoding at least 79 open reading frames and is flanked by several polyrepetitive DNA units (prDNA. As previously suggested, we showed that the prDNA unit located at the left prDNA-LUR junction (prDNA-G differs from the other prDNA units (prDNA-inner. Namely, the prDNA-G unit lacks the conserved pac-2 cleavage and packaging signal in its right terminal region. Based on the mechanisms of cleavage and packaging of herpesvirus genomes, this feature implies that only genomes bearing left and right end prDNA units are encapsulated into virions. Conclusions In this study, we have determined the complete genome sequence of the BAC-cloned BoHV-4 V.test strain and identified genome organization features that could be important in other herpesviruses.

The contribution of the expanding shell test to the modeling of elastoplaticity at high strain rates

International Nuclear Information System (INIS)

Llorca, Fabrice; Buy, Francois

2002-01-01

The expanding shell test allows to load a material in the domain of high strain levels while strain rate is about 104s-1. This test submits an hemisphere to a radial expanding free flight, using a pyrotechnic device. The experiment (experimental apparatus, measurements...) is described with the difficulties encountered for the interpretation of the experimental data. Under some assumptions, the numerical transformation of radial velocities gives indications about the evolution of the strain, stress, strain rate and temperature rise, this last one being related to plastic work. We show how it is possible to associate both analytical and numerical approaches. Numerical simulation of the test is presented in a companion paper (see [Buy01]). Results obtained for copper, tantalum and TA6V4 are presented. The contribution of this test to the modeling of elastoplastic behavior is discussed and further works are proposed

Higher Drop in Speed during a Repeated Sprint Test in Soccer Players Reporting Former Hamstring Strain Injury

Science.gov (United States)

Røksund, Ola D.; Kristoffersen, Morten; Bogen, Bård E.; Wisnes, Alexander; Engeseth, Merete S.; Nilsen, Ann-Kristin; Iversen, Vegard V.; Mæland, Silje; Gundersen, Hilde

2017-01-01

Aim: Hamstring strain injury is common in soccer. The aim of this study was to evaluate the physical capacity of players who have and have not suffered from hamstring strain injury in a sample of semi-professional and professional Norwegian soccer players in order to evaluate characteristics and to identify possible indications of insufficient rehabilitation. Method: Seventy-five semi-professional and professional soccer players (19 ± 3 years) playing at the second and third level in the Norwegian league participated in the study. All players answered a questionnaire, including one question about hamstring strain injury (yes/no) during the previous 2 years. They also performed a 40 m maximal sprint test, a repeated sprint test (8 × 20 m), a countermovement jump, a maximal oxygen consumption (VO2max) test, strength tests and flexibility tests. Independent sample t-tests were used to evaluate differences in the physical capacity of the players who had suffered from hamstring strain injury and those who had not. Mixed between-within subject's analyses of variance was used to compare changes in speed during the repeated sprint test between groups. Results: Players who reported hamstring strain injury during the previous two years (16%) had a significantly higher drop in speed (0.07 vs. 0.02 s, p = 0.007) during the repeated sprint test, compared to players reporting no previous hamstring strain injury. In addition, there was a significant interaction (groups × time) (F = 3.22, p = 0.002), showing that speed in the two groups changed differently during the repeated sprint test. There were no significant differences in relations to age, weight, height, body fat, linear speed, countermovement jump height, leg strength, VO2max, or hamstring flexibility between the groups. Conclusion: Soccer players who reported hamstring strain injury during the previous 2 years showed significant higher drop in speed during the repeated sprint test compared to players with no hamstring

Life prediction of l6 steel using strain-life curve and cyclic stress-strain curve by means of low cycle fatigue testing

Science.gov (United States)

Inamdar, Sanket; Ukhande, Manoj; Date, Prashant; Lomate, Dattaprasad; Takale, Shyam; Singh, RKP

2017-05-01

L6 Steel is used as die material in closed die hot forging process. This material is having some unique properties. These properties are due to its composition. Strain softening is the noticeable property of this material. Due to this in spite of cracking at high stress this material gets plastically deformed and encounters loss in time as well as money. Studies of these properties are necessary to nurture this material at fullest extent. In this paper, numerous experiments have been carried on L6 material to evaluate cyclic Stress - strain behavior as swell as strain-life behavior of the material. Low cycle fatigue test is carried out on MTS fatigue test machine at fully reverse loading condition R=-1. Also strain softening effect on forging metal forming process is explained in detail. The failed samples during low cycle fatigue test further investigated metallurgically on scanning electron microscopy. Based on this study, life estimation of hot forging die is carried out and it’s correlation with actual shop floor data is found out. This work also concludes about effect of pre-treatments like nitro-carburizing and surface coating on L6 steel material, to enhance its fatigue life to certain extent.

Biaxial direct tensile tests in a large range of strain rates. Results on a ferritic nuclear steel

Energy Technology Data Exchange (ETDEWEB)

Albertini, C.; Labibes, K.; Montagnani, M.; Pizzinato, E.V.; Solomos, G.; Viaccoz, B. [Commission of the European Communities, Ispra (Italy). Joint Research Centre

2000-09-01

Constitutive equations are usually calibrated only trough the experimental results obtained by means of unixial tests because of the lack of adequate biaxial experimental data especially at high strain rate conditions. These data are however important for the validation of analytical models and also for the predictions of mechanical behaviour of real structures subjected to multiaxial loading by numerical simulations. In this paper some developments are shown concerning biaxial cruciform specimens and different experimental machines allowing biaxial tests in a large range of strain rates. This experimental campaign has also allowed study of the influence of changing the strain paths. Diagrams of equivalent stress versus straining direction and also equivalent plastic fracture strain versus straining direction are shown. (orig.)

Final Test Analysis of Post Graduate Medical Residents

Directory of Open Access Journals (Sweden)

Maliheh Arab

2009-04-01

Full Text Available Background and purpose: Multiple choice questions are the most frequent test for medical students. It is important to analysis the overall response to individual  questions in the test.The aim of this study is to analyse questions of post graduate medical residency  tests.Methods: Final annual local (Ramadan medical school and national tests given to three Residency groups  including  17 Obstetrics  and gynecology testees,  7 pediatrics  and  12 internal  medicine  in 2004 were studied. In local tests residents answered to 148, 150 and 144 and in national  tests to ISO MCQS. Questions were  evaluated regarding cognitive domain level, Difficultly index and Discriminative index  and finally to evaluate  the optimal,  proper, acceptable and  ''must  omitted" questions.Results: Questions of local Obstetrics and gynecology, pediatrics and internal medicine tests evaluated the "recall" level in 72%, 72% and 51% and in national  tests 71%,  35% and 19%,  respectively. Questions  with  Discriminative indices  of 0.7 or more (proper  were 3 and  5% in  Obstetrics  and gynecology, 3.5% and 1% in pediatrics and 1% in local and national tests. Proper difficulty indices (30-70  were shown in 53% and 54% in Obstetrics  and gynecology, 34% and 43% in pediatrics and 40% and  42% in internal  medicine.  Generally  evaluating,  "must  omitted" questions in local and national tests were 76% in Obstetrics and gynecology, 81% and 79% in pediatrics and 91% and 85% in internal medicine. The most common causes making the questions to be considered  "must omitted" in studied tests were negative, zero or less than 0.2 Discriminative indices.Conclusion: Test analysis  of final  annual  local  (Ramadan medical  school  and national  tests  of Obstetrics  and gynecology, Pediatrics and internal medicine residency  programs  in 2004 revealed that most of the questions  are planned  in  "recall" level, harbor  improper

Application of Strain Energy on BIW Mode Optimization

Directory of Open Access Journals (Sweden)

Chang Guangbao

2015-01-01

Full Text Available This paper takes the BIW model as the research object, completes modal analysis, and verifies the finite element model by comparing the simulation results with the test results. In order to improve the frequency of BIW, the weak structure of D pillar is found and then optimized by the method of strain energy, and the frequency of BIW is changed from 28.80Hz to 32.15Hz. Finally, the method of strain energy has great positive effects on modal optimization.

Metallic nanoparticle-based strain sensors elaborated by atomic layer deposition

Science.gov (United States)

Puyoo, E.; Malhaire, C.; Thomas, D.; Rafaël, R.; R'Mili, M.; Malchère, A.; Roiban, L.; Koneti, S.; Bugnet, M.; Sabac, A.; Le Berre, M.

2017-03-01

Platinum nanoparticle-based strain gauges are elaborated by means of atomic layer deposition on flexible polyimide substrates. Their electro-mechanical response is tested under mechanical bending in both buckling and conformational contact configurations. A maximum gauge factor of 70 is reached at a strain level of 0.5%. Although the exponential dependence of the gauge resistance on strain is attributed to the tunneling effect, it is shown that the majority of the junctions between adjacent Pt nanoparticles are in a short circuit state. Finally, we demonstrate the feasibility of an all-plastic pressure sensor integrating Pt nanoparticle-based strain gauges in a Wheatstone bridge configuration.

Validation Tests of Fiber Optic Strain-Based Operational Shape and Load Measurements

Science.gov (United States)

Bakalyar, John A.; Jutte, Christine

2012-01-01

Aircraft design has been progressing toward reduced structural weight to improve fuel efficiency, increase performance, and reduce cost. Lightweight aircraft structures are more flexible than conventional designs and require new design considerations. Intelligent sensing allows for enhanced control and monitoring of aircraft, which enables increased structurally efficiency. The NASA Dryden Flight Research Center (DFRC) has developed an instrumentation system and analysis techniques that combine to make distributed structural measurements practical for lightweight vehicles. Dryden's Fiber Optic Strain Sensing (FOSS) technology enables a multitude of lightweight, distributed surface strain measurements. The analysis techniques, referred to as the Displacement Transfer Functions (DTF) and Load Transfer Functions (LTF), use surface strain values to calculate structural deflections and operational loads. The combined system is useful for real-time monitoring of aeroelastic structures, along with many other applications. This paper describes how the capabilities of the measurement system were demonstrated using subscale test articles that represent simple aircraft structures. Empirical FOSS strain data were used within the DTF to calculate the displacement of the article and within the LTF to calculate bending moments due to loads acting on the article. The results of the tests, accuracy of the measurements, and a sensitivity analysis are presented.

Impact Testing of Stainless Steel Materials

International Nuclear Information System (INIS)

R. K. Blandford; D. K. Morton; T. E. Rahl; S. D. Snow

2005-01-01

Stainless steels are used for the construction of numerous spent nuclear fuel or radioactive material containers that may be subjected to high strains and moderate strain rates (10 to 200 per second) during accidental drop events. Mechanical characteristics of these materials under dynamic (impact) loads in the strain rate range of concern are not well documented. The goal of the work presented in this paper was to improve understanding of moderate strain rate phenomena on these materials. Utilizing a drop-weight impact test machine and relatively large test specimens (1/2-inch thick), initial test efforts focused on the tensile behavior of specific stainless steel materials during impact loading. Impact tests of 304L and 316L stainless steel test specimens at two different strain rates, 25 per second (304L and 316L material) and 50 per second (304L material) were performed for comparison to their quasi-static tensile test properties. Elevated strain rate stress-strain curves for the two materials were determined using the impact test machine and a ''total impact energy'' approach. This approach considered the deformation energy required to strain the specimens at a given strain rate. The material data developed was then utilized in analytical simulations to validate the final elevated stress-strain curves. The procedures used during testing and the results obtained are described in this paper

Interaction of heat production, strain rate and stress power in a plastically deforming body under tensile test

Science.gov (United States)

Paglietti, A.

1982-01-01

At high strain rates the heat produced by plastic deformation can give rise to a rate dependent response even if the material has rate independent constitutive equations. This effect has to be evaluated when interpreting a material test, or else it could erroneously be ascribed to viscosity. A general thermodynamic theory of tensile testing of elastic-plastic materials is given in this paper; it is valid for large strain at finite strain rates. It enables discovery of the parameters governing the thermodynamic strain rate effect, provides a method for proper interpretation of the results of the tests of dynamic plasticity, and suggests a way of planning experiments in order to detect the real contribution of viscosity.

An objective approach for Burkholderia pseudomallei strain selection as challenge material for medical countermeasures efficacy testing

Directory of Open Access Journals (Sweden)

Kristopher E. Van Zandt

2012-09-01

Full Text Available Burkholderia pseudomallei is the causative agent of melioidosis, a rare disease of biodefense concern with high mortality and extreme difficulty in treatment. No human vaccines are available that protect against B. pseudomallei infection, and with the current limitations of antibiotic treatment, the development of new preventative and therapeutic interventions is crucial. Although clinical trials could be used to test the efficacy of new medical countermeasures (MCMs, the high mortality rates associated with melioidosis raises significant ethical issues concerning treating individuals with new compounds with unknown efficacies. The US Food and Drug Administration (FDA has formulated a set of guidelines for the licensure of new MCMs to treat diseases in which it would be unethical to test the efficacy of these drugs in humans. The FDA Animal Rule 21 CFR 314 calls for consistent, well-characterized B. pseudomallei strains to be used as challenge material in animal models. In order to facilitate the efficacy testing of new MCMs for melioidosis using animal models, we intend to develop a well-characterized panel of strains for use. This panel will comprise of strains that were isolated from human cases, have a low passage history, are virulent in animal models, and are well characterized phenotypically and genotypically. We have reviewed published and unpublished data on various B. pseudomallei strains to establish an objective method for selecting the strains to be included in the panel of B. pseudomallei strains with attention to five categories: animal infection models, genetic characterization, clinical and passage history, and availability of the strain to the research community. We identified 109 strains with data in at least one of the five categories, scored each strain based on the gathered data and identified 6 strains as candidate for a B. pseudomallei strain panel.

An objective approach for Burkholderia pseudomallei strain selection as challenge material for medical countermeasures efficacy testing.

Science.gov (United States)

Van Zandt, Kristopher E; Tuanyok, Apichai; Keim, Paul S; Warren, Richard L; Gelhaus, H Carl

2012-01-01

Burkholderia pseudomallei is the causative agent of melioidosis, a rare disease of biodefense concern with high mortality and extreme difficulty in treatment. No human vaccines are available that protect against B. pseudomallei infection, and with the current limitations of antibiotic treatment, the development of new preventative and therapeutic interventions is crucial. Although clinical trials could be used to test the efficacy of new medical countermeasures (MCMs), the high mortality rates associated with melioidosis raises significant ethical issues concerning treating individuals with new compounds with unknown efficacies. The US Food and Drug Administration (FDA) has formulated a set of guidelines for the licensure of new MCMs to treat diseases in which it would be unethical to test the efficacy of these drugs in humans. The FDA "Animal Rule" 21 CFR 314 calls for consistent, well-characterized B. pseudomallei strains to be used as challenge material in animal models. In order to facilitate the efficacy testing of new MCMs for melioidosis using animal models, we intend to develop a well-characterized panel of strains for use. This panel will comprise of strains that were isolated from human cases, have a low passage history, are virulent in animal models, and are well-characterized phenotypically and genotypically. We have reviewed published and unpublished data on various B. pseudomallei strains to establish an objective method for selecting the strains to be included in the panel of B. pseudomallei strains with attention to five categories: animal infection models, genetic characterization, clinical and passage history, and availability of the strain to the research community. We identified 109 strains with data in at least one of the five categories, scored each strain based on the gathered data and identified six strains as candidate for a B. pseudomallei strain panel.

Energy absorption at high strain rate of glass fiber reinforced mortars

Directory of Open Access Journals (Sweden)

Fenu Luigi

2015-01-01

Full Text Available In this paper, the dynamic behaviour of cement mortars reinforced with glass fibers was studied. The influence of the addition of glass fibers on energy absorption and tensile strength at high strain-rate was investigated. Static tests in compression, in tension and in bending were first performed. Dynamic tests by means of a Modified Hopkinson Bar were then carried out in order to investigate how glass fibers affected energy absorption and tensile strength at high strain-rate of the fiber reinforced mortar. The Dynamic Increase Factor (DIF was finally evaluated.

Fatigue Life Prediction of High Modulus Asphalt Concrete Based on the Local Stress-Strain Method

Directory of Open Access Journals (Sweden)

Mulian Zheng

2017-03-01

Full Text Available Previously published studies have proposed fatigue life prediction models for dense graded asphalt pavement based on flexural fatigue test. This study focused on the fatigue life prediction of High Modulus Asphalt Concrete (HMAC pavement using the local strain-stress method and direct tension fatigue test. First, the direct tension fatigue test at various strain levels was conducted on HMAC prism samples cut from plate specimens. Afterwards, their true stress-strain loop curves were obtained and modified to develop the strain-fatigue life equation. Then the nominal strain of HMAC course determined using finite element method was converted into local strain using the Neuber method. Finally, based on the established fatigue equation and converted local strain, a method to predict the pavement fatigue crack initiation life was proposed and the fatigue life of a typical HMAC overlay pavement which runs a risk of bottom-up cracking was predicted and validated. Results show that the proposed method was able to produce satisfactory crack initiation life.

The optics of the Final Focus Test Beam

International Nuclear Information System (INIS)

Irwin, J.; Brown, K.; Bulos, F.; Burke, D.; Helm, R.; Roy, G.; Ruth, R.; Yamamoto, N.; Oide, K.

1991-05-01

The Final Focus Test Beam (FFTB), currently under construction at the end of the SLAC Linac, is being built by an international collaboration as a test bed for ideas and methods required in the design and construction of final focus systems for next generation e + e - linear colliders. The FFTB lattice is based on the previously developed principle of using sextupole pairs in a dispersive region to compensate chromaticity. The linear lattice was optimized for length, and implementation of diagnostic procedures. The transformations between sextupole pairs (CCX and CCY) are exactly -I, the matrix for the intermediate transformer (BX) is exactly diagonal, and the dispersion function has zero slope at the sextupoles and is thus zero at the minimum of the β x function in the intermediate transformer. The introduction of sextupoles in final focus systems leads to the presence of additional optical aberrations, and synchrotron radiation in the dipoles also enlarges the final spot size. The important fourth-order optical aberrations which determine the main features of the design have been identified. Additional lower order aberrations arise in the implementation of these designs, since the real system is not the ideal design. We concentrate on these aberrations and describe strategies for their diagnosis and correction

Measurement test on creep strain rate of uranium-zirconium solid solutions

International Nuclear Information System (INIS)

Ogata, Takanari; Akabori, Mitsuo; Ogawa, Toru

1996-11-01

In order to measure creep strain rate of a small specimen of U-Zr solid solution, authors proposed an estimation method which was based upon the stress relaxation after compression. It was applied to measurement test on creep strain rate of the U-10wt%Zr specimen in the temperature range of 757 to 911degC. It may be concluded that the proposed method is valid, provided that the strain is within the appropriate range and that sufficient amount of the load decrement is observed. The obtained creep rate of U-10wt%Zr alloy indicated significantly smaller value, compared to the experimental data for pure U metal and evaluated data for U-Pu-Zr alloy. However, more careful measurement is desired in future since the present data are thought to be influenced by the precipitations included in the specimen. (author)

The emergence of the Activity Reduces Conflict Associated Strain (ARCAS) model: a test of a conditional mediation model of workplace conflict and employee strain

NARCIS (Netherlands)

Dijkstra, M.T.M.; Beersma, B.; Cornelissen, R.A.W.M.

2012-01-01

To test and extend the emerging Activity Reduces Conflict-Associated Strain (ARCAS) model, we predicted that the relationship between task conflict and employee strain would be weakened to the extent that people experience high organization-based self-esteem (OBSE). A survey among Dutch employees

The emergence of the activity reduces conflict related strain (ARCAS) model: A test of a conditional mediation model of workplace conflict and employee strain

NARCIS (Netherlands)

Dijkstra, M.T.M.; Beersma, B.; Cornelissen, R. A. W. M.

2012-01-01

To test and extend the emerging Activity Reduces Conflict-Associated Strain (ARCAS) model, we predicted that the relationship between task conflict and employee strain would be weakened to the extent that people experience high organization-based self-esteem (OBSE). A survey among Dutch employees

Standard test method for plane-strain (Chevron-Notch) fracture toughness of metallic materials

CERN Document Server

American Society for Testing and Materials. Philadelphia

1997-01-01

1.1 This test method covers the determination of plane-strain (chevron-notch) fracture toughnesses, KIv or KIvM, of metallic materials. Fracture toughness by this method is relative to a slowly advancing steady state crack initiated at a chevron-shaped notch, and propagating in a chevron-shaped ligament (Fig. 1). Some metallic materials, when tested by this method, exhibit a sporadic crack growth in which the crack front remains nearly stationary until a critical load is reached. The crack then becomes unstable and suddenly advances at high speed to the next arrest point. For these materials, this test method covers the determination of the plane-strain fracture toughness, KIvj or KIvM, relative to the crack at the points of instability. Note 1—One difference between this test method and Test Method E 399 (which measures KIc) is that Test Method E 399 centers attention on the start of crack extension from a fatigue precrack. This test method makes use of either a steady state slowly propagating crack, or a...

Static and dynamic pile testing of reinforced concrete piles with structure integrated fibre optic strain sensors

Science.gov (United States)

Schilder, Constanze; Kohlhoff, Harald; Hofmann, Detlef; Basedau, Frank; Habel, Wolfgang R.; Baeßler, Matthias; Niederleithinger, Ernst; Georgi, Steven; Herten, Markus

2013-05-01

Static and dynamic pile tests are carried out to determine the load bearing capacity and the quality of reinforced concrete piles. As part of a round robin test to evaluate dynamic load tests, structure integrated fibre optic strain sensors were used to receive more detailed information about the strains along the pile length compared to conventional measurements at the pile head. This paper shows the instrumentation of the pile with extrinsic Fabry-Perot interferometers sensors and fibre Bragg gratings sensors together with the results of the conducted static load test as well as the dynamic load tests and pile integrity tests.

Relationship between the Pedaling Biomechanics and Strain of Bicycle Frame during Submaximal Tests

Directory of Open Access Journals (Sweden)

Aneliya V. Manolova

2015-06-01

Full Text Available The aim of this study was to analyse the effect of forces applied to pedals and cranks on the strain imposed to an instrumented bicycle motocross (BMX frame. Using results from a finite element analysis to determine the localisation of highest stress, eight strain gauges were located on the down tube, the seat tube and the right chain stay. Before the pedaling tests, static loads were applied to the frame during bench tests. Two pedaling conditions have been analysed. In the first, the rider was in static standing position on the pedals and applied maximal muscular isometric force to the right pedal. The second pedaling condition corresponds to three pedaling sprint tests at submaximal intensities at 150, 300 and 550 W on a cycle-trainer. The results showed that smaller strain was observed in the pedaling condition than in the rider static standing position condition. The highest strains were located in the seat tube and the right chain stay near the bottom bracket area. The maximum stress observed through all conditions was 41 MPa on the right chain stay. This stress was 11 times lower than the yield stress of the frame material (460 MPa. This protocol could help to adapt the frame design to the riders as a function of their force and mechanical power output. These results could also help design BMX frames for specific populations (females and rider morphology.

Intramyocardial strain estimation from cardiac cine MRI.

Science.gov (United States)

Elnakib, Ahmed; Beache, Garth M; Gimel'farb, Georgy; El-Baz, Ayman

2015-08-01

Functional strain is one of the important clinical indicators for the quantification of heart performance and the early detection of cardiovascular diseases, and functional strain parameters are used to aid therapeutic decisions and follow-up evaluations after cardiac surgery. A comprehensive framework for deriving functional strain parameters at the endocardium, epicardium, and mid-wall of the left ventricle (LV) from conventional cine MRI data was developed and tested. Cine data were collected using short TR-/TE-balanced steady-state free precession acquisitions on a 1.5T Siemens Espree scanner. The LV wall borders are segmented using a level set-based deformable model guided by a stochastic force derived from a second-order Markov-Gibbs random field model that accounts for the object shape and appearance features. Then, the mid-wall of the segmented LV is determined based on estimating the centerline between the endocardium and epicardium of the LV. Finally, a geometrical Laplace-based method is proposed to track corresponding points on successive myocardial contours throughout the cardiac cycle in order to characterize the strain evolutions. The method was tested using simulated phantom images with predefined point locations of the LV wall throughout the cardiac cycle. The method was tested on 30 in vivo datasets to evaluate the feasibility of the proposed framework to index functional strain parameters. The cine MRI-based model agreed with the ground truth for functional metrics to within 0.30 % for indexing the peak systolic strain change and 0.29 % (per unit time) for indexing systolic and diastolic strain rates. The method was feasible for in vivo extraction of functional strain parameters. Strain indexes of the endocardium, mid-wall, and epicardium can be derived from routine cine images using automated techniques, thereby improving the utility of cine MRI data for characterization of myocardial function. Unlike traditional texture-based tracking, the

Final Report for Award DE-SC0005403. Improved Electrochemical Performance of Strained Lattice Electrolytes via Modulated Doping

Energy Technology Data Exchange (ETDEWEB)

Hertz, Joshua L. [Univ. of Delaware, Newark, DE (United States); Prasad, Ajay K. [Univ. of Delaware, Newark, DE (United States)

2015-09-06

The enclosed document provides a final report to document the research performed at the University of Delaware under Grant DE-SC0005403: Improved Electrochemical Performance of Strained Lattice Electrolytes via Modulated Doping. The ultimate goal of this project was to learn how to systematically strain the inter-atomic distance in thin ceramic films and how to use this newfound control to improve the ease by which oxygen ions can conduct through the films. Increasing the ionic conductivity of ceramics holds the promise of drastic improvements in the performance of solid oxide fuel cells, chemical sensors, gas permeation membranes, and related devices. Before this work, the experimental evidence advocating for strain-based techniques was often controversial and poorly characterized. Enabling much of this work was a new method to quickly create a very wide range of ceramic nanostructures that was established during the first phase of the project. Following this initial phase, we created a variety of promising nanostructured epitaxial films and multilayers with systematic variations in lattice mismatch and dopant content. Over the course of the work, a positive effect of tensile atomic strain on the oxygen conductivity was conclusively found using a few different forms of samples and experimental techniques. The samples were built by sputtering, an industrially scalable technique, and thus the technological implementation of these results may be economically feasible. Still, two other results consistently achieved over multiple efforts in this work give pause. The first of these results was that very specific, pristine surfaces upon which to build the nanostructures were strictly required in order to achieve measurable results. The second of these results was that compressively strained films with concomitant reductions in oxygen conductivity are much easier to obtain relative to tensile-strained films with increased conductivity.

Passive wireless antenna sensor for strain and crack sensing—electromagnetic modeling, simulation, and testing

International Nuclear Information System (INIS)

Yi, Xiaohua; Cho, Chunhee; Wang, Yang; Cooper, James; Tentzeris, Manos M; Leon, Roberto T

2013-01-01

This research investigates a passive wireless antenna sensor designed for strain and crack sensing. When the antenna experiences deformation, the antenna shape changes, causing a shift in the electromagnetic resonance frequency of the antenna. A radio frequency identification (RFID) chip is adopted for antenna signal modulation, so that a wireless reader can easily distinguish the backscattered sensor signal from unwanted environmental reflections. The RFID chip captures its operating power from an interrogation electromagnetic wave emitted by the reader, which allows the antenna sensor to be passive (battery-free). This paper first reports the latest simulation results on radiation patterns, surface current density, and electromagnetic field distribution. The simulation results are followed with experimental results on the strain and crack sensing performance of the antenna sensor. Tensile tests show that the wireless antenna sensor can detect small strain changes lower than 20 με, and can perform well at large strains higher than 10 000 με. With a high-gain reader antenna, the wireless interrogation distance can be increased up to 2.1 m. Furthermore, an array of antenna sensors is capable of measuring the strain distribution in close proximity. During emulated crack and fatigue crack tests, the antenna sensor is able to detect the growth of a small crack. (paper)

Results of Final Focus Test Beam

Energy Technology Data Exchange (ETDEWEB)

Walz, Dieter R

2003-06-13

The beam experiments of Final Focus Test Beam (FFTB) started in September 1993 at SLAC, and have produced a 1.7 {micro}m x 75 nm spot of 46 GeV electron beam. A number of new techniques involving two nanometer spot-size monitors have been developed. Several beam diagnostic/tuning schemes are applied to achieve and maintain the small spot. This experiment opens the way toward the nanometer world for future linear colliders.

Design and Testing of the Strain Transducer for Measuring Deformations of Pipelines Operating in the Mining-deformable Ground Environment

Directory of Open Access Journals (Sweden)

Gawedzki Waclaw

2015-10-01

Full Text Available Design and laboratory test results of the strain transducer intended for monitoring and assessing stress states of pipelines sited in mining areas are presented in this paper. This transducer allows measuring strains of pipelines subjected to external forces - being the mining operations effect. Pipeline strains can have a direct influence on a tightness loss and penetration of the transported fluid into the environment. The original strain gauge transducer was proposed for performing measurements of strains. It allows measuring circumferential strains and determining the value and direction of the main longitudinal strain. This strain is determined on the basis of measuring component longitudinal strains originating from axial forces and the resultant bending moment. The main purpose of investigations was the experimental verification of the possibility of applying the strain transducer for measuring strains of polyethylene pipelines. The obtained results of the transducer subjected to influences of tensile and compression forces are presented and tests of relaxation properties of polyethylene are performed.

The optics of the Final Focus Test Beam

International Nuclear Information System (INIS)

Irwin, J.; Brown, K.; Bulos, F.; Burke, D.; Helm, R.; Roy, G.; Ruth, R.; Yamamoto, N.; Oide, K.

1991-01-01

The Final Focus Test Beam (FFTB), currently under construction at the end of the SLAC Linac, is being built by an international collaboration as a test bed for ideas and methods required in the design and construction of final focus systems for next generation e + e - linear colliders. The FFTB lattice shown is based on the previously developed principle of using sextupole pairs in a dispersive region to compensate chromaticity. The linear lattice was optimized for length, and implementation of diagnostic procedures. The transformations between sextupole pairs (CCX and CCY) are exactly -I, the matrix for the intermediate transformer (BX) is exactly diagonal, and the dispersion function has zero slope at the sextupoles and is thus zero at the minimum of the β x function in the intermediate transformer

Monitoring of prestressed concrete pressure vessels. 1. An overview of concrete embedment strain instrumentation and calibration test results for selected concrete embedment strain meters

International Nuclear Information System (INIS)

Naus, D.J.; Hurtt, C.C.

1978-01-01

The report presents results of calibration tests on strain meters. The approach was divided into two phases: (1) an overview of meter performance criteria for PCPV applications and techniques for strain measurements in concrete and (2) procurement of commercially available gages and their evaluation to assess the reliability of manufacturer-supplied calibration factors. Calibration test results for gages embedded in 15.2-cm-diam by 54-cm cylindrical concrete specimens indicated that calibration factors should be determined (verified) by embedding samples of the gages in test specimens fabricated using a representative mix and that further research should be conducted on other measurement techniques based on inductance, capacitance, semiconductors, and fluidic principles

STAT, GAPS, STRAIN, DRWDIM: a system of computer codes for analyzing HTGR fuel test element metrology data. User's manual

Energy Technology Data Exchange (ETDEWEB)

Saurwein, J.J.

1977-08-01

A system of computer codes has been developed to statistically reduce Peach Bottom fuel test element metrology data and to compare the material strains and fuel rod-fuel hole gaps computed from these data with HTGR design code predictions. The codes included in this system are STAT, STRAIN, GAPS, and DRWDIM. STAT statistically evaluates test element metrology data yielding fuel rod, fuel body, and sleeve irradiation-induced strains; fuel rod anisotropy; and additional data characterizing each analyzed fuel element. STRAIN compares test element fuel rod and fuel body irradiation-induced strains computed from metrology data with the corresponding design code predictions. GAPS compares test element fuel rod, fuel hole heat transfer gaps computed from metrology data with the corresponding design code predictions. DRWDIM plots the measured and predicted gaps and strains. Although specifically developed to expedite the analysis of Peach Bottom fuel test elements, this system can be applied, without extensive modification, to the analysis of Fort St. Vrain or other HTGR-type fuel test elements.

Standard test method for linear-elastic plane-strain fracture toughness KIc of metallic materials

CERN Document Server

American Society for Testing and Materials. Philadelphia

2009-01-01

1.1 This test method covers the determination of fracture toughness (KIc) of metallic materials under predominantly linear-elastic, plane-strain conditions using fatigue precracked specimens having a thickness of 1.6 mm (0.063 in.) or greater subjected to slowly, or in special (elective) cases rapidly, increasing crack-displacement force. Details of test apparatus, specimen configuration, and experimental procedure are given in the Annexes. Note 1—Plane-strain fracture toughness tests of thinner materials that are sufficiently brittle (see 7.1) can be made using other types of specimens (1). There is no standard test method for such thin materials. 1.2 This test method is divided into two parts. The first part gives general recommendations and requirements for KIc testing. The second part consists of Annexes that give specific information on displacement gage and loading fixture design, special requirements for individual specimen configurations, and detailed procedures for fatigue precracking. Additional a...

Dynamic strain aging of twinning-induced plasticity (TWIP) steel in tensile testing and deep drawing

International Nuclear Information System (INIS)

Kim, J.G.; Hong, S.; Anjabin, N.; Park, B.H.; Kim, S.K.; Chin, K.-G.; Lee, S.; Kim, H.S.

2015-01-01

The dynamic strain aging (DSA) of metallic materials due to solute atom diffusion to mobile dislocations induce deformation instability with load fluctuations and deformation localizations, hence reducing their sheet formability. In this paper, DSA behaviors of twinning induced plasticity (TWIP) steel with and without Al during tensile testing and deep drawing are investigated in terms of strain localization and the Portevin-Le Chatelier (PLC) band. A theoretical DSA model with internal variables of dislocation density and twin volume fraction is presented for an estimation of strain localization and strain hardening behavior of TWIP steels. The simulation results of the load history and PLC bands during tensile testing and deep drawing are in good agreement with the experimental values. A serration behavior is observed in high-Mn TWIP steels and its tensile residual stress is higher than that in the Al-added TWIP steels, which results in a deformation crack or delayed fracture of deep drawn specimens

Yeast strains designed for 2. generation bioethanol production. Final report

Energy Technology Data Exchange (ETDEWEB)

Roennow, B.

2013-04-15

The aim of the project was to develop a suitable fermentation organism for 2G bioethanol production that would efficiently ferment all of the sugars in lignocellulosic biomass into ethanol at a commercially viable rate (comparable to yeast based 1G ethanol production). More specifically, a yeast strain would be developed with the ability to ferment also the pentoses in lignocellulosic biomass and thereby increase the ethanol yield of the process by 30-45% with a profound positive effect on the total process economy. The project has succeeded in developing a new industrial yeast strain V1. The yeast strain can transform the difficult C5 sugars to ethanol from waste products such as straw and the like from the agricultural sector. The classic issues relating to industrial uses such as inhibitor and ethanol tolerance and high ethanol production is resolved satisfactorily. The potential of the use of the new strain for 2nd generation bioethanol production is that the ethanol yields increase by 30-45%. With the increased ethanol yield follows a marked improvement in the overall process economics. (LN)

Strain-specific battery of tests for domains of mania: effects of valproate, lithium and imipramine

Directory of Open Access Journals (Sweden)

Shlomit Flaisher-Grinberg

2010-04-01

Full Text Available The lack of efficient animal models for bipolar disorder (BPD, especially for the manic pole, is a major factor hindering the research of its pathophysiology and the development of improved drug treatments. The present study was designed to identify an appropriate mouse strain for modeling some behavioral domains of mania and to evaluate the effects of drugs using this strain. The study compared the behavior of four strains: Black Swiss, C57Bl/6, CBA/J and A/J mice in a battery of tests that included spontaneous activity; sweet solution preference; light/dark box; resident-intruder; forced-swim and amphetamine-induced hyperactivity. Based on the ‘manic-like’ behavior demonstrated by the Black Swiss strain, the study evaluated the effects of the mood stabilizers valproate and lithium and of the antidepressant imipramine in the same tests using this strain. Results indicated that lithium and valproate attenuate the ‘manic-like’ behavior of Black Swiss mice whereas imipramine had no effects. These findings suggest that Black Swiss mice might be a good choice for modeling several domains of mania and distinguishing the effects of drugs on these specific domains. However, the relevance of the behavioral phenotype of Black Swiss mice to the biology of BPD is unknown at this time and future studies will investigate molecular differences between Black Swiss mice and other strains and asess the interaction between strain and mood stabilizing treatment.

New strain measurement method at axial tensile test of thin films through direct imaging

Energy Technology Data Exchange (ETDEWEB)

Ha, Jong-Eun [Department of Automotive Engineering, Seoul National Uinversity of Technolgy, 172 Gongneung-2 Dong, Nowon-Gu, Seoul (Korea, Republic of); Park, Jun-Hyub [Department of Mechatronics Engineering, College of Engineering, Tongmyong University, 535, Yongdang-Dong, Nam-Gu, Busan 608-711 (Korea, Republic of); Kang, Dong-Joong [School of Mechanical Eng., Pusan National University, Jangjeon-dong, Geumjeong-gu, Busan 609-735 (Korea, Republic of)], E-mail: jhyubpark@korea.com

2008-09-07

This paper proposes a new method for measuring strain during a tensile test of the specimen with micrometre size through direct imaging. A specimen was newly designed for adoption of direct imaging which was the main contribution of the proposed system. The structure of the specimen has eight indicators that make it possible to adopt direct imaging and it is fabricated using the same process of microelectromechanical system (MEMS) devices to guarantee the feasibility of the tensile test. We implemented a system for non-contact in situ measurement of strain with the specimen, the image-based displacement measurement system. Extension of the gauge length in the specimen could be found robustly by computing the positions of the eight rectangular-shape indicators on the image. Also, for an easy setup procedure, the region of interest was found automatically through the analysis of the edge projection profile along the horizontal direction. To gain confidence in the reliability of the system, the tensile test for the Al-3%Ti thin film was performed, which is widely used as a material in MEMS devices. Tensile tests were performed and displacements were measured using the proposed method and also the capacitance type displacement sensor for comparison. It is demonstrated that the new strain measurement system can be effectively used in the tensile test of the specimen at microscale with easy setup and better accuracy.

Characterization of hot bonding of bi-metal C45/25CrMo4 by plane strain compression test

Science.gov (United States)

Enaim, Mohammed; Langlois, Laurent; Zimmer-Chevret, Sandra; Bigot, Régis; Krumpipe, Pierre

2018-05-01

The need to produce multifunctional parts in order to conform to complex specifications becomes crucial in today's industrial context. This is why new processes are under study to develop multi-material parts which can satisfy this kind of requirements. This paper investigates the possibility of producing hot bonding of bi-metal C45/25CrMo4 parts by forging. This manufacturing process is a solid state joining process that involves, simultaneously, the welding and shaping of multi-material part. In this study, the C45/25CrMo4 bimetal was investigated. The forging is conducted at 1100°C and the influence of reduction rate on microstructure and bonding was investigated. The bonding model is inspired from Bay's model. Following this model, two parameters govern the solid-state bonding at the interface between materials: normal contact pressure and surface expansion. The objective is to check the bonding quality under different pressure and surface expansion. To achieve this goal, the plane strain compression test is chosen as the characterization test. Finally, simulations and experiments of this test are compared.

Impact of exopolysaccharide production on functional properties of some Lactobacillus salivarius strains.

Science.gov (United States)

Mercan, Emin; İspirli, Hümeyra; Sert, Durmuş; Yılmaz, Mustafa Tahsin; Dertli, Enes

2015-11-01

The aim of this work was to characterize functional properties of Lactobacillus salivarius strains isolated from chicken feces. Detection of genes responsible for exopolysaccharide (EPS) production revealed that all strains harbored a dextransucrase gene, but p-gtf gene was only detected in strain E4. Analysis of EPS production levels showed significant alterations among strains tested. Biofilm formation was found to be medium composition dependant, and there was a negative correlation with biofilm formation and EPS production. Autoaggregation properties and coaggregation of L. salivarius strains with chicken pathogens were appeared to be specific at strain level. An increment in bacterial adhesion to chicken gut explants was observed in L. salivarius strains with the reduction in EPS production levels. This study showed that strain-specific properties can determine the functional properties of L. salivarius strains, and the interference of these properties might be crucial for final selection of these strains for technological purposes.

Simple test of synergy between ampicillin and vancomycin for resistant strains of Enterococcus faecium.

Science.gov (United States)

Green, M; Barbadora, K; Wadowsky, R M

1994-11-01

The combination of ampicillin and vancomycin kills some but not all strains of ampicillin- and vancomycin-resistant Enterococcus faecium. We compared a simple test for synergy utilizing a commercially available microdilution susceptibility system with time-kill studies and determined acceptable breakpoints for this test for 20 strains of ampicillin- and vancomycin-resistant E. faecium. The combination of ampicillin and vancomycin was tested for synergy by time-kill, broth macrodilution, and broth microdilution procedures. Repeat testing of isolates by macro- and microdilution synergy methods yielded MICs that were within one twofold dilution of each other for both intra- and intertest comparisons. Synergy was always detected by time-kill studies when the MIC of ampicillin in the combination synergy screen was 16 micrograms/ml in the combination microdilution synergy screen. The determination of the synergy by the broth microdilution procedure appears to be simple, convenient, and accurate.

Construction of in-situ creep strain test facility for the SFR fuel cladding

Energy Technology Data Exchange (ETDEWEB)

Park, Sang Gyu; Heo, Hyeong Min; Kim, Jun Hwan; Kim, Sung Ho [KAERI, Daejeon (Korea, Republic of)

2016-05-15

In this study, in-situ laser inspection creep test machine was developed for the measuring the creep strain of SFR fuel cladding materials. Ferritic-martensitic steels are being considered as an attractive candidate material for a fuel cladding of a SFR due to their low expansion coefficients, high thermal conductivities and excellent irradiation resistances to a void swelling. HT9 steel (12CrMoVW) is initially developed as a material for power plants in Europe in the 1960. This steel has experienced to expose up to 200dpa in FFTE and EBR-II. Ferritic-Martensitic steel's maximum creep strength in existence is 180Mpa for 106 hour 600 .deg., but HT9 steel is 60Mpa. Because SFR is difficult to secure in developing and applying materials, HT9 steel has accumulated validated data and is suitable for SFR component. And also, because of its superior dimensional stability against fast neutron irradiation, Ferritic-martensitic steel of 9Cr and 12Cr steels, such as HT9 and FC92(12Cr-2W) are preferable to utilize in the fuel cladding of an SFR in KAERI. The pressurized thermal creep test of HT9 and FC92 claddings are being conducted in KAERI, but the change of creep strain in cladding is not easy to measure during the creep test due to its pressurized and closed conditions. In this paper, in-situ laser inspection pressurized creep test machine developed for SFR fuel cladding specimens is described. Moreover, the creep strain rate of HT9 at 650 .deg. C was examined from the in-situ laser inspection pressurized creep test machine.

Different commercial yeast strains affecting the volatile and sensory profile of cava base wine.

Science.gov (United States)

Torrens, Jordi; Urpí, Pilar; Riu-Aumatell, Montserrat; Vichi, Stefania; López-Tamames, Elvira; Buxaderas, Susana

2008-05-10

36 semi-industrial fermentations were carried out with 6 different yeast strains in order to assess differences in the wines' chemical and volatile profile. Two of the tested strains (Y3 and Y6) showed the fastest fermentation rates throughout 3 harvests and on 2 grape varieties. The wines fermented by three of the tested strains (Y5, Y3 and Y4) stand out for their high amounts of esters and possessed the highest fruity character. Wines from strains producing low amounts of esters and high concentrations of medium chain fatty acids, higher alcohols and six-carbon alcohols were the least appreciated at the sensory analysis. The data obtained in the present study show how the yeast strain quantitatively affects the final chemical and volatile composition of cava base wines and have repercussions on their sensory profile, independently of must variety and harvest year.

NMSBA: Aken Technologies Final Report: Toxicity Testing of Liquidoff

Energy Technology Data Exchange (ETDEWEB)

Ruffing, Anne [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jensen, Travis [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Strickland, Lucas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-02-01

To determine the effect of Liquidoff on bacteria, three bacterial strains were tested: Escherichia coli DH5α, Synechococcus sp. PCC 7002, and Synechococcus elongatus PCC 7942. E. coli DH5α is a Gram-negative, aerobic bacterium that is often found in normal gut flora and is commonly used the laboratory due to its fast growth rate. Synechococcus sp. PCC 7002 and S. elongatus PCC 7942 are Gram-negative, aquatic, autophototrophic cyanobacteria. Synechococcus sp. PCC 7002 is a marine cyanobacterium isolated from ‘fish pens’ on Magueyes Island, Puerto Rico in 1962, while S. elongatus PCC 7942 is a freshwater cyanobacterium. It should be noted that no Gram-positive bacterium was tested in this study.

Antimicrobial susceptibility testing of 230 Helicobacter pylori strains: importance of medium, inoculum, and incubation time

DEFF Research Database (Denmark)

Hartzen, S H; Andersen, L P; Bremmelgaard, A

1997-01-01

No standardized method of susceptibility testing for Helicobacter pylori is currently available, so before a large agar dilution study comprising 230 H. pylori strains belonging to more than 80 genetically different groups was initiated, we performed a relatively small preliminary study....../spot) as the inoculum and 72 h as the incubation time. A modest inoculum effect was noted for amoxicillin and metronidazole. By the methodology derived from our preliminary study, the susceptibilities of 230 H. pylori strains to six antibiotics were subsequently determined. The results were generally in accord...... with those of others, and apart from metronidazole, the MIC of which for approximately 25% of the strains tested was >8 microg/ml, resistance was low in Denmark. The situation might, however, quickly change when and if the number of indications for antibiotic therapy for H. pylori infections increase...

Evaluation test of high temperature strain gages used in a stethoscope for OGL-1 components in an elevated temperature service

Energy Technology Data Exchange (ETDEWEB)

Sato, Toshimi (Kyowa Electronic Inst. Co. Ltd. (Japan)); Tanaka, Isao; Komori, Yoshihiro; Suzuki; Toshiaki

1982-08-01

The stethoscope for OGL-1 components in a elevated temperature service (SOCETS) is a measuring system of evaluation integrity of structures for high temperature pipings during operations of Japan Material Testing Reactor. This paper is described about the results on fundamental performance on high temperature strain gages. From their test results that have been based on correlation of temperature-timestrain factors, it became clear that two weldable strain gages and a capacitance strain gage were available for strain measurements of OGL-1 components.

The Effects of Academic and Interpersonal Stress on Dating Violence among College Students: A Test of Classical Strain Theory

Science.gov (United States)

Mason, Brandon; Smithey, Martha

2012-01-01

This study examines Merton's Classical Strain Theory (1938) as a causative factor in intimate partner violence among college students. We theorize that college students experience general life strain and cumulative strain as they pursue the goal of a college degree. We test this strain on the likelihood of using intimate partner violence. Strain…

Clay behaviour under thermal gradients elastic and plastic strains

International Nuclear Information System (INIS)

Pintado, Xavier; Autio, Jorma; Punkkinen, Olli

2010-01-01

Document available in extended abstract form only. The nuclear waste repositories will generate strong temperature gradients at the clay barrier. The heat and water transport generate volume change in the clay. An experimental work is proposed here. The clay reference is the MX-80. The test device imposes a fixed heat flow in one side of the sample and maintains constant the temperature on the other side. Two samples are tested for symmetry. The samples are unconfined and the total mass of water remains constant. This situation creates a strong thermal gradient in the samples. The final radial strains in some places of the sample, the total vertical strain and the water content distribution will be measured just at the end of the test and some weeks later in order to distinguish the elastic strains from the plastic strains. The test period mustn't be longer than two weeks because a large quantity of water loses through the rubber membrane and the heads of the sample. The maximum temperature reached in the cooper is 90 degrees because with higher temperature, the rubber membrane is damaged. This test is already simulated by a numerical code. Thermal, thermo-hydraulic and thermo-hydro-mechanical analyses are being done. These analyses allow studying the different fluxes inside the sample and its quantification. Water content distribution is compared with the water content calculated from the reference parameters in the clay. The water distribution and the change of diameter after the test will also be studied. This experimental work will allow to know what is the percentage of the strains elastic or plastic and check the mechanical model. The experimental diameter change is compared with the diameter change calculated from the reference parameters of the clay. (authors)

Stress-strain relation of bentonite at undrained shear. Laboratory tests to investigate the influence of material composition and test technique

Energy Technology Data Exchange (ETDEWEB)

Dueck, Ann; Boergesson, Lennart; Johannesson, Lars-Erik (Clay Technology AB, Lund (Sweden))

2010-12-15

This report describes a laboratory study conducted to update the material model of the buffer material used in the analyses of the effect of a rock shear through a deposition hole. The study considers some new conditions and is especially focused on the reference case with MX-80Ca developed for SR-Site (MX-80 ion exchanged to Ca). The material model is based on relations between density, swelling pressure, shear strength and rate of strain. The reference model is described by Boergesson et al. (2010). The laboratory study is focused on undrained stress-strain-strength properties, which have been studied mainly by conducting triaxial tests and unconfined compression tests. The test results are compared to the earlier measurements and models which show that the new results fit very well into the general picture and models. For the new conditions suitable values of constants included in the model are proposed

Stress-strain relation of bentonite at undrained shear. Laboratory tests to investigate the influence of material composition and test technique

International Nuclear Information System (INIS)

Dueck, Ann; Boergesson, Lennart; Johannesson, Lars-Erik

2010-12-01

This report describes a laboratory study conducted to update the material model of the buffer material used in the analyses of the effect of a rock shear through a deposition hole. The study considers some new conditions and is especially focused on the reference case with MX-80Ca developed for SR-Site (MX-80 ion exchanged to Ca). The material model is based on relations between density, swelling pressure, shear strength and rate of strain. The reference model is described by Boergesson et al. (2010). The laboratory study is focused on undrained stress-strain-strength properties, which have been studied mainly by conducting triaxial tests and unconfined compression tests. The test results are compared to the earlier measurements and models which show that the new results fit very well into the general picture and models. For the new conditions suitable values of constants included in the model are proposed

The emergence of the Activity Reduces Conflict Associated Strain (ARCAS) model: a test of a conditional mediation model of workplace conflict and employee strain.

Science.gov (United States)

Dijkstra, Maria T M; Beersma, Bianca; Cornelissen, Roosmarijn A W M

2012-07-01

To test and extend the emerging Activity Reduces Conflict-Associated Strain (ARCAS) model, we predicted that the relationship between task conflict and employee strain would be weakened to the extent that people experience high organization-based self-esteem (OBSE). A survey among Dutch employees demonstrated that, consistent with the model, the conflict-employee strain relationship was weaker the higher employees' OBSE and the more they engaged in active problem-solving conflict management. Our data also revealed that higher levels of OBSE were related to more problem-solving conflict management. Moreover, consistent with the ARCAS model, we could confirm a conditional mediation model in which organization-based self-esteem through its relationship with problem-solving conflict management weakened the relationship between task conflict and employee strain. Potential applications of the results are discussed.

Incorporating comparative genomics into the design-test-learn cycle of microbial strain engineering.

Science.gov (United States)

Sardi, Maria; Gasch, Audrey P

2017-08-01

Engineering microbes with new properties is an important goal in industrial engineering, to establish biological factories for production of biofuels, commodity chemicals and pharmaceutics. But engineering microbes to produce new compounds with high yield remains a major challenge toward economically viable production. Incorporating several modern approaches, including synthetic and systems biology, metabolic modeling and regulatory rewiring, has proven to significantly advance industrial strain engineering. This review highlights how comparative genomics can also facilitate strain engineering, by identifying novel genes and pathways, regulatory mechanisms and genetic background effects for engineering. We discuss how incorporating comparative genomics into the design-test-learn cycle of strain engineering can provide novel information that complements other engineering strategies. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Effects of strain rate, test temperature and test environment on tensile properties of vandium alloys

International Nuclear Information System (INIS)

Gubbi, A.N.; Rowcliffe, A.F.; Eatherly, W.S.; Gibson, L.T.

1996-01-01

Tensile testing was carried out on SS-3 tensile specimens punched from 0.762-mm-thick sheets of the large heat of V-4Cr-4Ti and small heats of V-3Cr-3Ti and V-6Cr-6Ti. The tensile specimens were annealed at 1000 degrees for 2 h to obtain a fully recrystallized, fine grain microstructure with a grain size in the range of 10-19 μm. Room temperature tests at strain rates ranging from 10 -3 to 5 x 10 -1 /s were carried out in air; elevated temperature testing up to 700 degrees C was conducted in a vacuum better than 1 x 10 -5 torr ( -3 Pa). To study the effect of atomic hydrogen on ductility, tensile tests were conducted at room temperature in an ultra high vacuum chamber (UHV) with a hydrogen leak system

Evaluation test of high temperature strain gages used in a stethoscope for OGL-1 components in an elevated temperature service

International Nuclear Information System (INIS)

Sato, Toshimi; Tanaka, Isao; Komori, Yoshihiro; Suzuki; Toshiaki.

1982-01-01

The stethoscope for OGL-1 components in a elevated temperature service (SOCETS) is a measuring system of evaluation integrity of structures for high temperature pipings during operations of Japan Material Testing Reactor. This paper is described about the results on fundamental performance on high temperature strain gages. From their test results that have been based on correlation of temperature-timestrain factors, it became clear that two weldable strain gages and a capacitance strain gage were available for strain measurements of OGL-1 components. (author)

Performance of four different rat strains in the autoshaping, two-object discrimination, and swim maze tests of learning and memory.

Science.gov (United States)

Andrews, J S; Jansen, J H; Linders, S; Princen, A; Broekkamp, C L

1995-04-01

The performance of four strains of rats commonly used in behavioural research was assessed in three different tests of learning and memory. The four strains included three outbred lines (Long-Evans, Sprague-Dawley, Wistar) and one inbred strain (S3). Learning and memory were tested using three different paradigms: autoshaping of a lever press, a two-object discrimination test, and performance in a two-island swim maze task. The pigmented strains showed better performance in the autoshaping procedure: the majority of the Long-Evans and the S3 rats acquired the response, and the majority of the Wistar and Sprague-Dawley failed to acquire the response in the set time. The albino strains were slightly better in the swim maze than the pigmented strains. There appeared to be a speed/accuracy trade-off in the strategy used to solve the task. This was also evident following treatment with the cholinergic-depleting agent hemicholinium-3. The performance of the Long-Evans rats was most affected by the treatment in terms of accuracy and the Wistar and Sprague-Dawleys in terms of speed. In the two-object discrimination test only the Long-Evans showed satisfactory performance and were able to discriminate a novel from a known object a short interval after initial exposure. These results show large task- and strain-dependent differences in performance in tests of learning and memory. Some of the performance variation may be due to emotional differences between the strains and may be alleviated by extra training. However, the response to pharmacological manipulation may require more careful evaluation.(ABSTRACT TRUNCATED AT 250 WORDS)

Anthraquinone Final Reporting and Recordkeeping Requirements and Test Rule

Science.gov (United States)

EPA is issuing a final rule, under section 4 of the Toxic Substances Control Act (TSCA), requiring manufacturers and processors of 9,10-anthraquinone (CAS No. 84—65—1), hereinafter anthraquinone, to perform testing.

Testing the initial-final mass relationship of white dwarfs

International Nuclear Information System (INIS)

Catalan, S; Isern, J; Garcia-Berro, E; Ribas, I

2009-01-01

In this contribution we revisit the initial-final mass relationship of white dwarfs, which links the mass of a white dwarf with that of its progenitor in the main-sequence. Although this function is of paramount importance to several fields in modern astrophysics, it is still not well constrained either from the theoretical or the observational points of view. We present here a revision of the present semi-empirical initial-final mass relationship using all the available data and including our recent results obtained from studying white dwarfs in common proper motion pairs. We have also analyzed the results obtained so far to provide some clues on the dependence of this relationship on metallicity. Finally, we have also performed an indirect test of the initial-final mass relationship by studying its effect on the luminosity function and on the mass distribution of white dwarfs.

Bullying Victimization and Adolescent Self-Harm: Testing Hypotheses from General Strain Theory

Science.gov (United States)

Hay, Carter; Meldrum, Ryan

2010-01-01

Self-harm is widely recognized as a significant adolescent social problem, and recent research has begun to explore its etiology. Drawing from Agnew's (1992) social psychological strain theory of deviance, this study considers this issue by testing three hypotheses about the effects of traditional and cyber bullying victimization on deliberate…

Use of Strain Measurements from Acoustic Bench Tests of the Battleship Flowliner Test Articles To Link Analytical Model Results to In-Service Resonant Response

Science.gov (United States)

Frady, Greg; Smaolloey, Kurt; LaVerde, Bruce; Bishop, Jim

2004-01-01

The paper will discuss practical and analytical findings of a test program conducted to assist engineers in determining which analytical strain fields are most appropriate to describe the crack initiating and crack propagating stresses in thin walled cylindrical hardware that serves as part of the Space Shuttle Main Engine's fuel system. In service the hardware is excited by fluctuating dynamic pressures in a cryogenic fuel that arise from turbulent flow/pump cavitation. A bench test using a simplified system was conducted using acoustic energy in air to excite the test articles. Strain measurements were used to reveal response characteristics of two Flowliner test articles that are assembled as a pair when installed in the engine feed system.

Effects of strain rate, test temperature and test environment on tensile properties of vandium alloys

Energy Technology Data Exchange (ETDEWEB)

Gubbi, A.N.; Rowcliffe, A.F.; Eatherly, W.S.; Gibson, L.T. [Oak Ridge National Lab., TN (United States)

1996-10-01

Tensile testing was carried out on SS-3 tensile specimens punched from 0.762-mm-thick sheets of the large heat of V-4Cr-4Ti and small heats of V-3Cr-3Ti and V-6Cr-6Ti. The tensile specimens were annealed at 1000{degrees} for 2 h to obtain a fully recrystallized, fine grain microstructure with a grain size in the range of 10-19 {mu}m. Room temperature tests at strain rates ranging from 10{sup {minus}3} to 5 x 10{sup {minus}1}/s were carried out in air; elevated temperature testing up to 700{degrees}C was conducted in a vacuum better than 1 x 10{sup {minus}5} torr (<10{sup {minus}3} Pa). To study the effect of atomic hydrogen on ductility, tensile tests were conducted at room temperature in an ultra high vacuum chamber (UHV) with a hydrogen leak system.

Forming limit curves of DP600 determined in high-speed Nakajima tests and predicted by two different strain-rate-sensitive models

Science.gov (United States)

Weiß-Borkowski, Nathalie; Lian, Junhe; Camberg, Alan; Tröster, Thomas; Münstermann, Sebastian; Bleck, Wolfgang; Gese, Helmut; Richter, Helmut

2018-05-01

Determination of forming limit curves (FLC) to describe the multi-axial forming behaviour is possible via either experimental measurements or theoretical calculations. In case of theoretical determination, different models are available and some of them consider the influence of strain rate in the quasi-static and dynamic strain rate regime. Consideration of the strain rate effect is necessary as many material characteristics such as yield strength and failure strain are affected by loading speed. In addition, the start of instability and necking depends not only on the strain hardening coefficient but also on the strain rate sensitivity parameter. Therefore, the strain rate dependency of materials for both plasticity and the failure behaviour is taken into account in crash simulations for strain rates up to 1000 s-1 and FLC can be used for the description of the material's instability behaviour at multi-axial loading. In this context, due to the strain rate dependency of the material behaviour, an extrapolation of the quasi-static FLC to dynamic loading condition is not reliable. Therefore, experimental high-speed Nakajima tests or theoretical models shall be used to determine the FLC at high strain rates. In this study, two theoretical models for determination of FLC at high strain rates and results of experimental high-speed Nakajima tests for a DP600 are presented. One of the theoretical models is the numerical algorithm CRACH as part of the modular material and failure model MF GenYld+CrachFEM 4.2, which is based on an initial imperfection. Furthermore, the extended modified maximum force criterion considering the strain rate effect is also used to predict the FLC. These two models are calibrated by the quasi-static and dynamic uniaxial tensile tests and bulge tests. The predictions for the quasi-static and dynamic FLC by both models are presented and compared with the experimental results.

Development of Final Running Test System for Digital Systems

Energy Technology Data Exchange (ETDEWEB)

Lee, Kwang-Dae; Lee, Eui-Jong; Lim, Hee-Taek; Kim, Min-Seok [KHNP Central Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In nuclear industry, the newly designed systems to upgrade are qualified to meet IEEE standards and the regulatory guidelines for their functions, performance and reliability requirements. Failure Mode and Effect Analysis, Fault Tree Analysis, and Hazard Analysis have been used to improve the reliability of the control system. To ensure the completeness of the software, the verification and validation processes are carried out during the development process. In spite of the many efforts depending on the analysis and procedures, there are limitations to improve the reliability. The lessons learned from the currently installed system failures show the incompleteness of the final integration test. The current point-to-point and logic-to-logic separate test procedures manually performed by the engineers can cause some procedures missed and have effects on the critical functions. The design processes of the digital systems are met in accordance with the international standards and regulatory guidelines. The lessons learned from the failures of the running digital systems showed the limitations of the current verification and validation efforts. The various improvements and attempts have been considered including the expert review processes and the completeness of the test. In this paper, the Final Running Test Method evaluating the completeness of the digital system using the control patterns and the Test System Architecture are proposed.

Development of Final Running Test System for Digital Systems

International Nuclear Information System (INIS)

Lee, Kwang-Dae; Lee, Eui-Jong; Lim, Hee-Taek; Kim, Min-Seok

2016-01-01

In nuclear industry, the newly designed systems to upgrade are qualified to meet IEEE standards and the regulatory guidelines for their functions, performance and reliability requirements. Failure Mode and Effect Analysis, Fault Tree Analysis, and Hazard Analysis have been used to improve the reliability of the control system. To ensure the completeness of the software, the verification and validation processes are carried out during the development process. In spite of the many efforts depending on the analysis and procedures, there are limitations to improve the reliability. The lessons learned from the currently installed system failures show the incompleteness of the final integration test. The current point-to-point and logic-to-logic separate test procedures manually performed by the engineers can cause some procedures missed and have effects on the critical functions. The design processes of the digital systems are met in accordance with the international standards and regulatory guidelines. The lessons learned from the failures of the running digital systems showed the limitations of the current verification and validation efforts. The various improvements and attempts have been considered including the expert review processes and the completeness of the test. In this paper, the Final Running Test Method evaluating the completeness of the digital system using the control patterns and the Test System Architecture are proposed

Measurement of Strain and Strain Rate during the Impact of Tennis Ball Cores

Directory of Open Access Journals (Sweden)

Ben Lane

2018-03-01

Full Text Available The aim of this investigation was to establish the strains and strain rates experienced by tennis ball cores during impact to inform material characterisation testing and finite element modelling. Three-dimensional surface strains and strain rates were measured using two high-speed video cameras and corresponding digital image correlation software (GOM Correlate Professional. The results suggest that material characterisation testing to a maximum strain of 0.4 and a maximum rate of 500 s−1 in tension and to a maximum strain of −0.4 and a maximum rate of −800 s−1 in compression would encapsulate the demands placed on the material during impact and, in turn, define the range of properties required to encapsulate the behavior of the material during impact, enabling testing to be application-specific and strain-rate-dependent properties to be established and incorporated in finite element models.

Dynamic strains for earthquake source characterization

Science.gov (United States)

Barbour, Andrew J.; Crowell, Brendan W

2017-01-01

Strainmeters measure elastodynamic deformation associated with earthquakes over a broad frequency band, with detection characteristics that complement traditional instrumentation, but they are commonly used to study slow transient deformation along active faults and at subduction zones, for example. Here, we analyze dynamic strains at Plate Boundary Observatory (PBO) borehole strainmeters (BSM) associated with 146 local and regional earthquakes from 2004–2014, with magnitudes from M 4.5 to 7.2. We find that peak values in seismic strain can be predicted from a general regression against distance and magnitude, with improvements in accuracy gained by accounting for biases associated with site–station effects and source–path effects, the latter exhibiting the strongest influence on the regression coefficients. To account for the influence of these biases in a general way, we include crustal‐type classifications from the CRUST1.0 global velocity model, which demonstrates that high‐frequency strain data from the PBO BSM network carry information on crustal structure and fault mechanics: earthquakes nucleating offshore on the Blanco fracture zone, for example, generate consistently lower dynamic strains than earthquakes around the Sierra Nevada microplate and in the Salton trough. Finally, we test our dynamic strain prediction equations on the 2011 M 9 Tohoku‐Oki earthquake, specifically continuous strain records derived from triangulation of 137 high‐rate Global Navigation Satellite System Earth Observation Network stations in Japan. Moment magnitudes inferred from these data and the strain model are in agreement when Global Positioning System subnetworks are unaffected by spatial aliasing.

Expanded studies of linear collider final focus systems at the Final Focus Test Beam

International Nuclear Information System (INIS)

Tenenbaum, P.G.

1995-12-01

In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research

Expanded studies of linear collider final focus systems at the Final Focus Test Beam

Energy Technology Data Exchange (ETDEWEB)

Tenenbaum, Peter Gregory [Stanford Univ., CA (United States)

1995-12-01

In order to meet their luminosity goals, linear colliders operating in the center-of-mass energy range from 3,50 to 1,500 GeV will need to deliver beams which are as small as a few Manometers tall, with x:y aspect ratios as large as 100. The Final Focus Test Beam (FFTB) is a prototype for the final focus demanded by these colliders: its purpose is to provide demagnification equivalent to those in the future linear collider, which corresponds to a focused spot size in the FFTB of 1.7 microns (horizontal) by 60 manometers (vertical). In order to achieve the desired spot sizes, the FFTB beam optics must be tuned to eliminate aberrations and other errors, and to ensure that the optics conform to the desired final conditions and the measured initial conditions of the beam. Using a combination of incoming-beam diagnostics. beam-based local diagnostics, and global tuning algorithms, the FFTB beam size has been reduced to a stable final size of 1.7 microns by 70 manometers. In addition, the chromatic properties of the FFTB have been studied using two techniques and found to be acceptable. Descriptions of the hardware and techniques used in these studies are presented, along with results and suggestions for future research.

Temperature Buffer Test. Final THM modelling

Energy Technology Data Exchange (ETDEWEB)

Aakesson, Mattias; Malmberg, Daniel; Boergesson, Lennart; Hernelind, Jan [Clay Technology AB, Lund (Sweden); Ledesma, Alberto; Jacinto, Abel [UPC, Universitat Politecnica de Catalunya, Barcelona (Spain)

2012-01-15

The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aespoe HRL. It was installed during the spring of 2003. Two heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report presents the final THM modelling which was resumed subsequent to the dismantling operation. The main part of this work has been numerical modelling of the field test. Three different modelling teams have presented several model cases for different geometries and different degree of process complexity. Two different numerical codes, Code{sub B}right and Abaqus, have been used. The modelling performed by UPC-Cimne using Code{sub B}right, has been divided in three subtasks: i) analysis of the response observed in the lower part of the test, by inclusion of a number of considerations: (a) the use of the Barcelona Expansive Model for MX-80 bentonite; (b) updated parameters in the vapour diffusive flow term; (c) the use of a non-conventional water retention curve for MX-80 at high temperature; ii) assessment of a possible relation between the cracks observed in the bentonite blocks in the upper part of TBT, and the cycles of suction and stresses registered in that zone at the start of the experiment; and iii) analysis of the performance, observations and interpretation of the entire test. It was however not possible to carry out a full THM analysis until the end of the test due to

Temperature Buffer Test. Final THM modelling

International Nuclear Information System (INIS)

Aakesson, Mattias; Malmberg, Daniel; Boergesson, Lennart; Hernelind, Jan; Ledesma, Alberto; Jacinto, Abel

2012-01-01

The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aespoe HRL. It was installed during the spring of 2003. Two heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report presents the final THM modelling which was resumed subsequent to the dismantling operation. The main part of this work has been numerical modelling of the field test. Three different modelling teams have presented several model cases for different geometries and different degree of process complexity. Two different numerical codes, Code B right and Abaqus, have been used. The modelling performed by UPC-Cimne using Code B right, has been divided in three subtasks: i) analysis of the response observed in the lower part of the test, by inclusion of a number of considerations: (a) the use of the Barcelona Expansive Model for MX-80 bentonite; (b) updated parameters in the vapour diffusive flow term; (c) the use of a non-conventional water retention curve for MX-80 at high temperature; ii) assessment of a possible relation between the cracks observed in the bentonite blocks in the upper part of TBT, and the cycles of suction and stresses registered in that zone at the start of the experiment; and iii) analysis of the performance, observations and interpretation of the entire test. It was however not possible to carry out a full THM analysis until the end of the test due to

Variation in the strain anisotropy of Zircaloy with temperature and strain

International Nuclear Information System (INIS)

Hindle, E.D.; Worswick, D.

1984-01-01

The strong crystallographic texture which is developed during the fabrication of zirconium-based alloys causes pronounced anisotropy in their mechanical properties, particularly deformation. The tendency for circular-section tension specimens with a high concentration of basal poles in one direction to become elliptical when deformed in tension has been used in this study to provide quantitative data on the effects of both strain and temperature on strain anisotropy. Tension tests were carried out over a temperature range of 293 to 1193 K on specimens machined from Zircaloy-2 plate. The strain anisotropy was found to increase markedly at temperatures over 923 K, reaching a maximum in the region of 1070 K. The strain anisotropy increased with increasing strain in this temperature region. The study was extended to Zircaloy-4 pressurized-water reactor fuel cladding by carrying out tube swelling tests and evaluating the axial deformation produced. Although scatter in the test results was higher than that exhibited in the tension tests, the general trend in the data was similar. The effects of the strain anisotropy observed are discussed in relation to the effects of temperature on the ductility of Zircaloy fuel cladding tubes during postulated largebreak loss-of-coolant accidents

Effects of canine parvovirus strain variations on diagnostic test results and clinical management of enteritis in dogs.

Science.gov (United States)

Markovich, Jessica E; Stucker, Karla M; Carr, Alaina H; Harbison, Carole E; Scarlett, Janet M; Parrish, Colin R

2012-07-01

To estimate the prevalence of canine parvovirus (CPV) strains among dogs with enteritis admitted to a referral hospital in the southwestern United States during an 11-month period and to compare diagnostic test results, disease severity, and patient outcome among CPV strains. Prospective observational study. 72 dogs with histories and clinical signs of parvoviral enteritis. For each dog, a fecal sample or rectal swab specimen was evaluated for CPV antigen via an ELISA. Subsequently, fecal samples (n = 42 dogs) and pharyngeal swab specimens (16) were obtained and tested for CPV antigen via an ELISA and CPV DNA via a PCR assay. For specimens with CPV-positive results via PCR assay, genetic sequencing was performed to identify the CPV strain. 56 dogs tested positive for CPV via ELISA or PCR assay. For 42 fecal samples tested via both ELISA and PCR assay, 27 had positive results via both assays, whereas 6 had positive PCR assay results only. Ten pharyngeal swab specimens yielded positive PCR assay results. Genetic sequencing was performed on 34 fecal or pharyngeal swab specimens that had CPV-positive PCR assay results; 25 (73.5%) were identified as containing CPV type-2c, and 9 (26.5%) were identified as containing CPV type-2b. No association was found between CPV strain and disease severity or clinical outcome. CPV type-2b and CPV type-2c posed similar health risks for dogs; therefore, genetic sequencing of CPV does not appear necessary for clinical management of infected patients. The diagnostic tests used could detect CPV type-2c.

High strain rate studies in rock

International Nuclear Information System (INIS)

Grady, D.

1977-01-01

Dynamic compression studies using high velocity impact are usually considered to involve a catastrophic process of indeterminate loading rate by which a material is brough to a shock compressed state. Although this is frequently the case, methods are also available to control the rate of strain during the shock compression process. One of the most accurate of these methods makes use of the anomalous nonlinear elastic property of glass to transform an initial shock or step wave input into a ramp wave of known amplitude and duration. Fused silica is the most carefully calibrated material for this purpose and, when placed between the test specimen and the impact projectile, can provide loading strain rates in the range of 10 4 /s to 10 6 /s for final stress states of approximately 3.9 GPa or less.Ramp wave compression experiments have been conducted on dolomite at strain rates of 3 x 10 4 /s. Both initial yielding and subsequent deformation at this strain rate agrees well with previous shock wave studies (epsilon-dotapprox.10 6 /s) and differs substantially from quasi-static measurements (epsilon-dotapprox.10 -4 /s). The ramp wave studies have also uncovered a pressure-induced phase transition in dolomite initiating at 4.0 GPa

Final design of the neutral beam lines for the Tokamak Fusion Test Reactor

International Nuclear Information System (INIS)

Pittenger, L.C.; Valby, L.E.; Stone, R.R.; Pedrotti, L.R.; Denhoy, B.; Yoard, R.

1979-01-01

Final design of the neutral beam lines for TFTR has been completed. A prototype has been assembled at Lawrence Berkeley Laboratory and is undergoing testing as part of the Neutral Beam System Test Facility (NBSTF). The final neutral beam line (NBL) configuration differs in several details from that previously reported upon; certain components have been added; and testing of the cryopump system has led to some design simplification. It is these developments which are reported herein

Evaluation of Dynamic Deformation Behaviors in Metallic Materials under High Strain-Rates Using Taylor Bar Impact Test

Energy Technology Data Exchange (ETDEWEB)

Bae, Kyung Oh; Shin, Hyung Seop [Andong National Univ., Andong (Korea, Republic of)

2016-09-15

To ensure the reliability and safety of various mechanical systems in accordance with their high-speed usage, it is necessary to evaluate the dynamic deformation behavior of structural materials under impact load. However, it is not easy to understand the dynamic deformation behavior of the structural materials using experimental methods in the high strain-rate range exceeding 10{sup 4} s{sup -1}. In this study, the Taylor bar impact test was conducted to investigate the dynamic deformation behavior of metallic materials in the high strain-rate region, using a high-speed photography system. Numerical analysis of the Taylor bar impact test was performed using AUTODYN S/W. The results of the analysis were compared with the experimental results, and the material behavior in the high strain-rate region was discussed.

Final design of ITER port plug test facility

Energy Technology Data Exchange (ETDEWEB)

Cerisier, Thierry, E-mail: thierry.cerisier@yahoo.fr [ITER Organization, Route de Vinon-sur-Verdon, CS 90046, St Paul-lez-Durance Cedex, 13067 (France); Levesy, Bruno [ITER Organization, Route de Vinon-sur-Verdon, CS 90046, St Paul-lez-Durance Cedex, 13067 (France); Romannikov, Alexander [Institution “Project Center ITER”, Kurchatov sq. 1, Building 3, Moscow 123182 (Russian Federation); Rumyantsev, Yuri [JSC “Cryogenmash”, Moscow reg., Balashikha 143907 (Russian Federation); Cordier, Jean-Jacques; Dammann, Alexis [ITER Organization, Route de Vinon-sur-Verdon, CS 90046, St Paul-lez-Durance Cedex, 13067 (France); Minakov, Victor; Rosales, Natalya; Mitrofanova, Elena [JSC “Cryogenmash”, Moscow reg., Balashikha 143907 (Russian Federation); Portone, Sergey; Mironova, Ekaterina [Institution “Project Center ITER”, Kurchatov sq. 1, Building 3, Moscow 123182 (Russian Federation)

2016-11-01

Highlights: • We introduce the port plug test facility (purpose and status of the design). • We present the PPTF sub-systems. • We present the environmental and functional tests. • We present the occupational and nuclear safety functions. • We conclude on the achievements and next steps. - Abstract: To achieve the overall ITER machine availability target, the availability of diagnostics and heating port plugs shall be as high as 99.5%. To fulfill this requirement, it is mandatory to test the port plugs at operating temperature before installation on the machine and after refurbishment. The ITER port plug test facility (PPTF) is composed of several test stands that can be used to test the port plugs whereas at the end of manufacturing (in a non-nuclear environment), or after refurbishment in the ITER hot cell facility. The PPTF provides the possibility to perform environmental (leak tightness, vacuum and thermo-hydraulic performances) and functional tests (radio frequency acceptance tests, behavior of the plugs’ steering mechanism and calibration of diagnostics) on upper and equatorial port plugs. The final design of the port plug test facility is described. The configuration of the standalone test stands and the integration in the hot cell facility are presented.

Pilot study on proximal femur strains during locomotion and fall-down scenario

Energy Technology Data Exchange (ETDEWEB)

Klodowski, Adam, E-mail: adam.klodowski@lut.fi; Valkeapaeae, Antti, E-mail: antti.valkeapaa@lut.fi; Mikkola, Aki, E-mail: aki.mikkola@lut.fi [Lappeenranta University of Technology (Finland)

2012-09-15

The most common and severe type of fracture among the elderly is known as a proximal femur fracture. Aging-related bone loss is one of the major contributing factors to increased likelihood of bone fracture. Specific exercises can be used to strain bones and increase bone strength to counter the effects of bone loss. The flexible multibody simulation approach can be used as a non-invasive method for estimating bone strains caused by physical activity. This method was recently used to analyze the strain of locomotion in regard to human femur and tibia leg bones. The current study focuses on strain analysis of the femoral neck. The research test person was a clinically healthy 65-year old Caucasian male. The computed tomography was used to build a geometrically accurate finite element model of the femur with inhomogeneous material properties derived from the voxel data. The anthropometric data was used to model the musculoskeletal system of the test person. The multibody skeletal model was utilized to estimate loading on the femoral neck during walking, which represents a routine daily activity. The flexible multibody simulation results were compared to strains that occurred during a simulated fall onto the greater trochanter of the femur. The fall simulation was made entirely using finite element software. Results from the finite element analysis were compared with the previous study showing that the test person does not belong to the high-risk hip fracture group. Finally, the estimated strains gathered from the walking simulation were compared to the strain values from the simulated fall-down scenario.

Computer-aided dispatch--traffic management center field operational test final detailed test plan : WSDOT deployment

Science.gov (United States)

2003-10-01

The purpose of this document is to expand upon the evaluation components presented in "Computer-aided dispatch--traffic management center field operational test final evaluation plan : WSDOT deployment". This document defines the objective, approach,...

40 CFR 85.1509 - Final admission of modification and test vehicles.

Science.gov (United States)

2010-07-01

... test vehicles. 85.1509 Section 85.1509 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Importation of Motor Vehicles and Motor Vehicle Engines § 85.1509 Final admission of modification and test vehicles. (a) Except...

Evaluation of the use of various rat strains for immunogenic potency tests of Sabin-derived inactivated polio vaccines.

Science.gov (United States)

Someya, Yuichi; Ami, Yasushi; Takai-Todaka, Reiko; Fujimoto, Akira; Haga, Kei; Murakami, Kosuke; Fujii, Yoshiki; Shirato, Haruko; Oka, Tomoichiro; Shimoike, Takashi; Katayama, Kazuhiko; Wakita, Takaji

2018-03-01

Slc:Wistar rats have been the only strain used in Japan for purpose of evaluating a national reference vaccine for the Sabin-derived inactivated polio vaccine (sIPV) and the immunogenicity of sIPV-containing products. However, following the discovery that the Slc:Wistar strain was genetically related to the Fischer 344 strain, other "real" Wistar strains, such as Crlj:WI, that are available worldwide were tested in terms of their usefulness in evaluating the immunogenicity of the past and current lots of a national reference vaccine. The response of the Crlj:WI rats against the serotype 1 of sIPV was comparable to that of the Slc:Wistar rats, while the Crlj:WI rats exhibited a higher level of response against the serotypes 2 and 3. The immunogenic potency units of a national reference vaccine determined using the Slc:Wistar rats were reproduced on tests using the Crlj:WI rats. These results indicate that a titer of the neutralizing antibody obtained in response to a given dose of sIPV cannot be directly compared between these two rat strains, but that, more importantly, the potency units are almost equivalent for the two rat strains. Copyright © 2018 International Alliance for Biological Standardization. Published by Elsevier Ltd. All rights reserved.

Strain Rate Effect on Tensile Behavior for a High Specific Strength Steel: From Quasi-Static to Intermediate Strain Rates

Directory of Open Access Journals (Sweden)

Wei Wang

2017-12-01

Full Text Available The strain rate effect on the tensile behaviors of a high specific strength steel (HSSS with dual-phase microstructure has been investigated. The yield strength, the ultimate strength and the tensile toughness were all observed to increase with increasing strain rates at the range of 0.0006 to 56/s, rendering this HSSS as an excellent candidate for an energy absorber in the automobile industry, since vehicle crushing often happens at intermediate strain rates. Back stress hardening has been found to play an important role for this HSSS due to load transfer and strain partitioning between two phases, and a higher strain rate could cause even higher strain partitioning in the softer austenite grains, delaying the deformation instability. Deformation twins are observed in the austenite grains at all strain rates to facilitate the uniform tensile deformation. The B2 phase (FeAl intermetallic compound is less deformable at higher strain rates, resulting in easier brittle fracture in B2 particles, smaller dimple size and a higher density of phase interfaces in final fracture surfaces. Thus, more energy need be consumed during the final fracture for the experiments conducted at higher strain rates, resulting in better tensile toughness.

Strains and Stressors: An Analysis of Touchscreen Learning in Genetically Diverse Mouse Strains

Science.gov (United States)

Graybeal, Carolyn; Bachu, Munisa; Mozhui, Khyobeni; Saksida, Lisa M.; Bussey, Timothy J.; Sagalyn, Erica; Williams, Robert W.; Holmes, Andrew

2014-01-01

Touchscreen-based systems are growing in popularity as a tractable, translational approach for studying learning and cognition in rodents. However, while mouse strains are well known to differ in learning across various settings, performance variation between strains in touchscreen learning has not been well described. The selection of appropriate genetic strains and backgrounds is critical to the design of touchscreen-based studies and provides a basis for elucidating genetic factors moderating behavior. Here we provide a quantitative foundation for visual discrimination and reversal learning using touchscreen assays across a total of 35 genotypes. We found significant differences in operant performance and learning, including faster reversal learning in DBA/2J compared to C57BL/6J mice. We then assessed DBA/2J and C57BL/6J for differential sensitivity to an environmental insult by testing for alterations in reversal learning following exposure to repeated swim stress. Stress facilitated reversal learning (selectively during the late stage of reversal) in C57BL/6J, but did not affect learning in DBA/2J. To dissect genetic factors underlying these differences, we phenotyped a family of 27 BXD strains generated by crossing C57BL/6J and DBA/2J. There was marked variation in discrimination, reversal and extinction learning across the BXD strains, suggesting this task may be useful for identifying underlying genetic differences. Moreover, different measures of touchscreen learning were only modestly correlated in the BXD strains, indicating that these processes are comparatively independent at both genetic and phenotypic levels. Finally, we examined the behavioral structure of learning via principal component analysis of the current data, plus an archival dataset, totaling 765 mice. This revealed 5 independent factors suggestive of “reversal learning,” “motivation-related late reversal learning,” “discrimination learning,” “speed to respond,” and �

Dynamic testing at high strain rates of an ultrafine-grained magnesium alloy processed by ECAP

International Nuclear Information System (INIS)

Li, B.; Joshi, S.; Azevedo, K.; Ma, E.; Ramesh, K.T.; Figueiredo, R.B.; Langdon, T.G.

2009-01-01

A ZK60 magnesium alloy was processed by equal-channel angular pressing (ECAP) at 473 K to produce a grain size of ∼0.8 μm and it was then tested under dynamic conditions at strain rates up to 4.0 x 10 3 s -1 using a split-Hopkinson bar. The stress-strain curves in dynamic testing exhibited upwards concave curvature suggesting the occurrence of twinning. Examination by transmission electron microscopy showed that dislocation slip played a major role in the flow behavior with dislocation accumulation as the main source of work hardening. An identification of Burgers vectors revealed the extensive presence of prismatic dislocations. Rod-shaped Mg 1 (Zn,Zr) 1 precipitates present in the as-received alloy become fragmented and overaged during ECAP.

Susceptibilities of Mycoplasma bovis, Mycoplasma dispar, and Ureaplasma diversum strains to antimicrobial agents in vitro.

Science.gov (United States)

ter Laak, E A; Noordergraaf, J H; Verschure, M H

1993-02-01

The purpose of this study was to determine the susceptibility of various strains of Mycoplasma bovis, Mycoplasma dispar, and Ureaplasma diversum, which are prevalent causes of pneumonia in calves, to 16 antimicrobial agents in vitro. The MICs of the antimicrobial agents were determined by a serial broth dilution method for 16 field strains and the type strain of M. bovis, for 19 field strains and the type strain of M. dispar, and for 17 field strains of U. diversum. Final MICs for M. bovis and M. dispar were read after 7 days and final MICs for U. diversum after 1 to 2 days. All strains tested were susceptible to tylosin, kitasamycin, and tiamulin but were resistant to nifuroquine and streptomycin. Most strains of U. diversum were intermediately susceptible to oxytetracycline but fully susceptible to chlortetracycline; most strains of M. bovis and M. dispar, however, were resistant to both agents. Strains of M. dispar and U. diversum were susceptible to doxycycline and minocycline, but strains of M. bovis were only intermediately susceptible. Susceptibility or resistance to chloramphenicol, spiramycin, spectinomycin, lincomycin, or enrofloxacin depended on the species but was not equal for the three species. The type strains of M. bovis and M. dispar were more susceptible to various antimicrobial agents, including tetracyclines, than the field strains. This finding might indicate that M. bovis and M. dispar strains are becoming resistant to these agents. Antimicrobial agents that are effective in vitro against all three mycoplasma species can be considered for treating mycoplasma infections in pneumonic calves. Therefore, tylosin, kitasamycin, and tiamulin may be preferred over oxytetracycline and chlortetracycline.

High Strain Rate Testing of Rocks using a Split-Hopkinson-Pressure Bar

Science.gov (United States)

Zwiessler, Ruprecht; Kenkmann, Thomas; Poelchau, Michael; Nau, Siegfried; Hess, Sebastian

2016-04-01

Dynamic mechanical testing of rocks is important to define the onset of rate dependency of brittle failure. The strain rate dependency occurs through the propagation velocity limit (Rayleigh wave speed) of cracks and their reduced ability to coalesce, which, in turn, significantly increases the strength of the rock. We use a newly developed pressurized air driven Split-Hopkinson-Pressure Bar (SHPB), that is specifically designed for the investigation of high strain rate testing of rocks, consisting of several 10 to 50 cm long strikers and bar components of 50 mm in diameter and 2.5 meters in length each. The whole set up, composed of striker, incident- and transmission bar is available in aluminum, titanium and maraging steel to minimize the acoustic impedance contrast, determined by the change of density and speed of sound, to the specific rock of investigation. Dynamic mechanical parameters are obtained in compression as well as in spallation configuration, covering a wide spectrum from intermediate to high strain rates (100-103 s-1). In SHPB experiments [1] one-dimensional longitudinal compressive pulses of diverse shapes and lengths - formed with pulse shapers - are used to generate a variety of loading histories under 1D states of stress in cylindrical rock samples, in order to measure the respective stress-strain response at specific strain rates. Subsequent microstructural analysis of the deformed samples is aimed at quantification fracture orientation, fracture pattern, fracture density, and fracture surface properties as a function of the loading rate. Linking mechanical and microstructural data to natural dynamic deformation processes has relevance for the understanding of earthquakes, landslides, impacts, and has several rock engineering applications. For instance, experiments on dynamic fragmentation help to unravel super-shear rupture events that pervasively pulverize rocks up to several hundred meters from the fault core [2, 3, 4]. The dynamic, strain

Review of tolerances at the Final Focus Test Beam

International Nuclear Information System (INIS)

Bulos, F.; Burke, D.; Helm, R.; Irwin, J.; Roy, G.; Yamamoto, N.

1991-01-01

The authors review the tolerances associated with the Final Focus Test Beam (FFTB). The authors have computed the acceptability window of the input beam for orbit jitter, emittance beta functions mismatch, incoming dispersion and coupling; tolerances on magnet alignment, strength and multipole content; and the initial tuneability capture of the line

Computer-aided dispatch--traffic management center field operational test final test plans : state of Utah

Science.gov (United States)

2004-01-01

The purpose of this document is to expand upon the evaluation components presented in "Computer-aided dispatch--traffic management center field operational test final evaluation plan : state of Utah". This document defines the objective, approach, an...

Screening local Lactobacilli from Iran in terms of production of lactic acid and identification of superior strains

Directory of Open Access Journals (Sweden)

Fatemeh Soleimanifard

2015-12-01

Full Text Available Introduction: Lactobacilli are a group of lactic acid bacteria that their final product of fermentation is lactic acid. The objective of this research is selection of local Lactobacilli producing L (+ lactic acid. Materials and methods: In this research the local strains were screened based on the ability to produce lactic acid. The screening was performed in two stages. The first stage was the titration method and the second stage was the enzymatic method. The superior strains obtained from titration method were selected to do enzymatic test. Finally, the superior strains in the second stage (enzymatic which had the ability to produce L(+ lactic acid were identified by biochemical tests. Then, molecular identification of strains was performed by using 16S rRNA sequencing. Results: In this study, the ability of 79 strains of local Lactobacilli in terms of production of lactic acid was studied. The highest and lowest rates of lactic acid production was 34.8 and 12.4 mg/g. Superior Lactobacilli in terms of production of lactic acid ability of producing had an optical isomer L(+, the highest levels of L(+ lactic acid were with 3.99 and the lowest amount equal to 1.03 mg/g. The biochemical and molecular identification of superior strains showed that strains are Lactobacillus paracasei. Then the sequences of 16S rRNA of superior strains were reported in NCBI with accession numbers KF735654، KF735655، KJ508201and KJ508202. Discussion and conclusion: The amounts of lactic acid production by local Lactobacilli were very different and producing some of these strains on available reports showed more products. The results of this research suggest the use of superior strains of Lactobacilli for production of pure L(+ lactic acid.

Plasma lenses for SLAC Final Focus Test facility

International Nuclear Information System (INIS)

Betz, D.; Cline, D.; Joshi, C.; Rajagopalan, S.; Rosenzweig, J.; Su, J.J.; Williams, R.; Chen, P.; Gundersen, M.; Katsouleas, T.; Norem, J.

1991-01-01

A collaborative group of accelerator and plasma physicists and engineers has formed with an interest in exploring the use of plasma lenses to meet the needs of future colliders. Analytic and computational models of plasma lenses are briefly reviewed and several design examples for the SLAC Final Focus Test Beam are presented. The examples include discrete, thick, and adiabatic lenses. A potential plasma source with desirable lens characteristics is presented

Final turbine and test facility design report Alden/NREC fish friendly turbine

Energy Technology Data Exchange (ETDEWEB)

Cook, Thomas C. [Alden Research Lab., Holden, MA (United States); Cain, Stuart A. [Alden Research Lab., Holden, MA (United States); Fetfatsidis, Paul [Alden Research Lab., Holden, MA (United States); Hecker, George E. [Alden Research Lab., Holden, MA (United States); Stacy, Philip S. [Alden Research Lab., Holden, MA (United States)

2000-09-01

The final report provides an overview of the Alden/NREC Fish Friendly turbine design phase, turbine test plan, preliminary test results, costs, schedule, and a hypothetical application at a real world project.

The impact of mouse passaging of Mycobacterium tuberculosis strains prior to virulence testing in the mouse and guinea pig aerosol models.

Directory of Open Access Journals (Sweden)

Paul J Converse

2010-04-01

Full Text Available It has been hypothesized that the virulence of lab-passaged Mycobacterium tuberculosis and recombinant M. tuberculosis mutants might be reduced due to multiple in vitro passages, and that virulence might be augmented by passage of these strains through mice before quantitative virulence testing in the mouse or guinea pig aerosol models.By testing three M. tuberculosis H37Rv samples, one deletion mutant, and one recent clinical isolate for survival by the quantitative organ CFU counting method in mouse or guinea pig aerosol or intravenous infection models, we could discern no increase in bacterial fitness as a result of passaging of M. tuberculosis strains in mice prior to quantitative virulence testing in two animal models. Surface lipid expression as assessed by neutral red staining and thin-layer chromatography for PDIM analysis also failed to identify virulence correlates.These results indicate that animal passaging of M. tuberculosis strains prior to quantitative virulence testing in mouse or guinea pig models does not enhance or restore potency to strains that may have lost virulence due to in vitro passaging. It is critical to verify virulence of parental strains before genetic manipulations are undertaken and comparisons are made.

Review of tolerances at the Final Focus Test Beam

International Nuclear Information System (INIS)

Bulos, F.; Burke, D.; Helm, R.; Irwin, J.; Roy, G.; Yamamoto, N.

1991-05-01

We review the tolerances associated with the Final Focus Test Beam (FFTB). We have computed the acceptability window of the input beam for orbit jitter, emittance beta functions mismatch, incoming dispersion and coupling; tolerances on magnet alignment, strength and multipole content; and the initial tuneability capture of the line. 2 refs., 1 fig

Quantitative investigation of ligament strains during physical tests for sacroiliac joint pain using finite element analysis.

Science.gov (United States)

Kim, Yoon Hyuk; Yao, Zhidong; Kim, Kyungsoo; Park, Won Man

2014-06-01

It may be assumed that the stability is affected when some ligaments are injured or loosened, and this joint instability causes sacroiliac joint pain. Several physical examinations have been used to diagnose sacroiliac pain and to isolate the source of the pain. However, more quantitative and objective information may be necessary to identify unstable or injured ligaments during these tests due to the lack of understanding of the quantitative relationship between the physical tests and the biomechanical parameters that may be related to pains in the sacroiliac joint and the surrounding ligaments. In this study, a three-dimensional finite element model of the sacroiliac joint was developed and the biomechanical conditions for six typical physical tests such as the compression test, distraction test, sacral apex pressure test, thigh thrust test, Patrick's test, and Gaenslen's test were modelled. The sacroiliac joint contact pressure and ligament strain were investigated for each test. The values of contact pressure and the combination of most highly strained ligaments differed markedly among the tests. Therefore, these findings in combination with the physical tests would be helpful to identify the pain source and to understand the pain mechanism. Moreover, the technology provided in this study might be a useful tool to evaluate the physical tests, to improve the present test protocols, or to develop a new physical test protocol. Copyright © 2013 Elsevier Ltd. All rights reserved.

KNK I Test Program, Final Report Part 1

International Nuclear Information System (INIS)

Kathol, W.

1976-01-01

The compact sodium cooled nuclear reactor KNK I of the Karlsruhe Research Center reached full power for the first time in February 1974. The goal of KNK I is to collect experience for the construction and operation of larger reactors, such as SNR 300. In order to deepen these experiences, a test program was drawn up and conducted from 1973 until 1975 within the framework of R and D work on the development of fast breeder reactors. The program included individual tasks concerning reactor design, safety instrumentation, irradiation and post-examination as well as behavior of components during operation. The performance of the tests was essentially governed by the licensing procedure imposed under the atomic energy act for the construction and operation of nuclear facilities. This report is the first part of the final report of the test program

Preclinical test: bacterial reverse mutation test for 18F-fluorocholine produced in CDTN

International Nuclear Information System (INIS)

Mendes, Bruno M.; Bispo, Ana Carolina A.; Campos, Danielle C.; Silva, Juliana B.

2013-01-01

The choline labeled with fluorine-18 (18FCH) is being considered as a great importance radiopharmaceutical due to its effective detection of many type of malignant neoplasm. The research related to 18 F-fluorocholine synthesis in CDTN was initiated in 2010. In order to obtain clinical research approval, as well as to register 18 FCH for marketing, safety and efficacy preclinical testing are required. The present work evaluated the 18 FCH genotoxic potential through the bacterial reverse mutation test (Ames test) using Salmonella typhimurium TA-98, TA-100, TA-1535 and TA-1537 strains and Escherichia coli WP2 uvrA strain. The reverse mutation test in bacteria for fluorcolina was conducted in two stages. Initially the method was applied to 'cold' fluorocholine molecule (19FCH). Subsequently, the decayed product of 18 FCH synthesis was evaluated. The first step was performed in order to examine the FCH molecule mutagenicity. The second was carried out to determine the mutagenic potential of final product. All strains were tested in triplicate for each exposure concentration, in the presence and absence of metabolic activation (S-9 mix - 10%). There were no statistically significant increases in revertant colonies rate for any strains tested after their exposure to decayed 18 FCH or 19 FCH. The number of revertant colonies in positive controls was significantly higher than that observed in significant increases in revertant colonies rate for any strains tested after their exposure to decayed 18 FCH or 19 FCH. The number of revertant colonies in positive controls was significantly higher than that observed in negative controls. Based on results of this assay, 18 FCH and 19 FCH, at tested doses, were found to be non-mutagenic in bacterial reverse mutation test. (author)

Final design and performance of in situ testing in Grimsel

International Nuclear Information System (INIS)

Fuentes-Cantillana, J.L.; Garcia-SiNeriz, J.L.

1998-01-01

This report is focused on the design, engineering, and construction aspects of the in situ test carried out at the Grimsel underground laboratory in Switzerland. This reproduces the AGP-granite concept of ENRESA for HLW repositories in crystalline rock. Two heaters, similar in dimensions and weight to the canisters in the reference concept, have been placed in a horizontal drift with a 2.28-m diameter, a total test length of 17.4 m, and backfilled with a total of 115.7 † of highly-compacted bentonite blocks. The backfilled area has been closed with a concrete plug which is 2.7 m thick. More than 600 sensors have been installed in the test to monitor different parameters such as temperature, pressures, humidity, etc., within both the buffer material and the host rock. The installation was completed and commissioned in February 1997, and then the heating phase, which will last for at least 3 years, was started. During this period, the test will basically be operated in an automatic mode, controlled and monitored from Spain via modem. The report is the Final Report from AITEMIN for Phase 4 of the project and includes a description of the test configuration and layout; the design, engineering, and manufacturing aspects of the different test components and equipment; the emplacement operation; and the as built information regarding the final position of the main components and the sensors. (Author)

Strain ratio effects on low-cycle fatigue behavior and deformation microstructure of 2124-T851 aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Hao, Hong, E-mail: 10928008@zju.edu.cn [Institute for Process Equipment, Zhejiang University, Hangzhou 310027 (China); School of Environment and Safety, Taiyuan University of Science and Technology, Taiyuan 030024 (China); Ye, Duyi, E-mail: duyi_ye@zju.edu.cn [Institute for Process Equipment, Zhejiang University, Hangzhou 310027 (China); Chen, Chuanyong [Institute for Process Equipment, Zhejiang University, Hangzhou 310027 (China)

2014-05-01

The low-cycle fatigue tests of 2124-T851 aluminum alloy with strain ratios of −1, −0.06, 0.06 and 0.5 were conducted under constant amplitude at room temperature. Microstructural and fractographic examinations of the material after fatigue tests were performed by optical microscopy (OM) and scanning electron microscopy (SEM), respectively. Firstly, the results showed that the material exhibited cyclic softening characteristic as a whole. The degree of softening decreased linearly with the increasing strain amplitude and the decreasing strain ratio. The lower fatigue life and ductility of the material corresponded to the larger strain ratios. Secondly, microstructure observations revealed that the density and length of slip bands increased with the increasing strain ratio at the given strain amplitude, and so did the volume fraction and size of coarse constituents, which were responsible for the reduction of fatigue life and ductility of the material. Finally, the SEM micrographs revealed that multiple crack initiation sites took place on the fracture surfaces at different strain ratios. The reduction of stable crack growth area with the increasing strain ratio was observed. Unstable crack growth region was only observed under R≠−1.

Strain accumulation in quasicrystalline solids

International Nuclear Information System (INIS)

Nori, F.; Ronchetti, M.; Elser, V.

1988-01-01

We study the relaxation of 2D quasicrystalline elastic networks when their constituent bonds are perturbed homogeneously. Whereas ideal, quasiperiodic networks are stable against such perturbations, we find significant accumulations of strain in a class of disordered networks generated by a growth process. The grown networks are characterized by root mean square phason fluctuations which grow linearly with system size. The strain accumulation we observe in these networks also grows linearly with system size. Finally, we find a dependence of strain accumulation on cooling rate

Structural-performance testing of titanium-shell lead-matrix container MM2

Energy Technology Data Exchange (ETDEWEB)

Hosaluk, L. J.; Barrie, J. N.

1992-05-15

This report describes the hydrostatic structural-performance testing of a half-scale, titanium-shell, lead-matrix container (MM2) with a large, simulated volumetric casting defect. Mechancial behaviour of the container is assessed from extensive surface-strain measurements and post-test non-destructive and destructive examinations. Measured strain data are compared briefly with analytical results from a finite-element model of a previous test prototype, MM1, and with data generated by a finite-difference computer code. Finally, procedures are recommended for more detailed analytical modelling. (auth)

Design, construction and testing of a DC bioeffects test enclosure for small animals. Final report

Energy Technology Data Exchange (ETDEWEB)

Frazier, M J; Preache, M M

1980-11-01

This final report describes both the engineering development of a DC bioeffects test enclosure for small laboratory animals, and the biological protocol for the use of such enclosures in the testing of animals to determine possible biological effects of the environment associated with HVDC transmission lines. The test enclosure which has been designed is a modular unit, which will house up to eight rat-sized animals in individual compartments. Multiple test enclosures can be used to test larger numbers of animals. A prototype test enclosure has been fabricated and tested to characterize its electrical performance characteristics. The test enclosure provides a simulation of the dominant environment associated with HVDC transmission lines; namely, a static electric field and an ion current density. A biological experimental design has been developed for assessing the effects of the dominant components of the HVDC transmission line environment.

Preclinical test: bacterial reverse mutation test for {sup 18}F-fluorocholine produced in CDTN

Energy Technology Data Exchange (ETDEWEB)

Mendes, Bruno M.; Bispo, Ana Carolina A.; Campos, Danielle C.; Silva, Juliana B., E-mail: bmm@cdtn.br, E-mail: acab@cdtn.br, E-mail: dcc@cdtn.br, E-mail: silvajb@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2013-07-01

The choline labeled with fluorine-18 (18FCH) is being considered as a great importance radiopharmaceutical due to its effective detection of many type of malignant neoplasm. The research related to {sup 18}F-fluorocholine synthesis in CDTN was initiated in 2010. In order to obtain clinical research approval, as well as to register {sup 18}FCH for marketing, safety and efficacy preclinical testing are required. The present work evaluated the {sup 18}FCH genotoxic potential through the bacterial reverse mutation test (Ames test) using Salmonella typhimurium TA-98, TA-100, TA-1535 and TA-1537 strains and Escherichia coli WP2 uvrA strain. The reverse mutation test in bacteria for fluorcolina was conducted in two stages. Initially the method was applied to 'cold' fluorocholine molecule (19FCH). Subsequently, the decayed product of {sup 18}FCH synthesis was evaluated. The first step was performed in order to examine the FCH molecule mutagenicity. The second was carried out to determine the mutagenic potential of final product. All strains were tested in triplicate for each exposure concentration, in the presence and absence of metabolic activation (S-9 mix - 10%). There were no statistically significant increases in revertant colonies rate for any strains tested after their exposure to decayed {sup 18}FCH or {sup 19}FCH. The number of revertant colonies in positive controls was significantly higher than that observed in significant increases in revertant colonies rate for any strains tested after their exposure to decayed {sup 18}FCH or {sup 19}FCH. The number of revertant colonies in positive controls was significantly higher than that observed in negative controls. Based on results of this assay, {sup 18}FCH and {sup 19}FCH, at tested doses, were found to be non-mutagenic in bacterial reverse mutation test. (author)

Mechanical strength model for plastic bonded granular materials at high strain rates and large strains

International Nuclear Information System (INIS)

Browning, R.V.; Scammon, R.J.

1998-01-01

Modeling impact events on systems containing plastic bonded explosive materials requires accurate models for stress evolution at high strain rates out to large strains. For example, in the Steven test geometry reactions occur after strains of 0.5 or more are reached for PBX-9501. The morphology of this class of materials and properties of the constituents are briefly described. We then review the viscoelastic behavior observed at small strains for this class of material, and evaluate large strain models used for granular materials such as cap models. Dilatation under shearing deformations of the PBX is experimentally observed and is one of the key features modeled in cap style plasticity theories, together with bulk plastic flow at high pressures. We propose a model that combines viscoelastic behavior at small strains but adds intergranular stresses at larger strains. A procedure using numerical simulations and comparisons with results from flyer plate tests and low rate uniaxial stress tests is used to develop a rough set of constants for PBX-9501. Comparisons with the high rate flyer plate tests demonstrate that the observed characteristic behavior is captured by this viscoelastic based model. copyright 1998 American Institute of Physics

Strain Rockbursts Simulated by Low-Strength Brittle Equivalent Materials

Directory of Open Access Journals (Sweden)

Lang Li

2016-01-01

Full Text Available This paper presents experimental study on rockbursts that occur in deep underground excavations. To begin with, the boundary conditions for excavation in deep underground engineering were analysed and elastic adaptive boundary is an effective way to minimize the boundary effect of geomechanical model test. Then, in order to simulate an elastic adaptive loading boundary, Belleville springs were used to establish this loading boundary. With the aforementioned experimental set-ups and fabrication of similarity models for test, the phenomena of strain mode rockbursts were satisfactorily reproduced in laboratory. The internal stress, strain, and convergences of the openings of the model were instrumented by subtly preembedded sensors and transducers. Test results showed that, with an initial state of high stress from both upper layers’ gravitational effects and in situ stress due to tectonic movements, the excavation brings a dramatic rise in the hoop stress and sharp drop in radial stress, which leads to the splitting failure of rock mass. Finally a rockburst occurred associated with the release of strain energy stored in highly stressed rock mass. In addition, the failure of the surrounding rock demonstrated an obvious hysteresis effect which supplies valuable guide and reference for tunnel support. Not only do these results provide a basis for further comprehensive experiments, but also the data can offer assisting aids for further theoretical study of rockbursts.

Modelling and simulation of dynamic recrystallization (DRX) in OFHC copper at very high strain rates

Science.gov (United States)

Testa, G.; Bonora, N.; Ruggiero, A.; Iannitti, G.; Persechino, I.; Hörnqvist, M.; Mortazavi, N.

2017-01-01

At high strain rates, deformation processes are essentially adiabatic and if the plastic work is large enough dynamic recrystallization can occur. In this work, an examination on microstructure evolution of OFHC copper in Dynamic Tensile Extrusion (DTE) test, performed at 400 m/s, was carried out. EBSD investigations, along the center line of the fragment remaining in the extrusion die, showed a progressive elongation of the grains, and an accompanying development of a strong + dual fiber texture. Discontinuous dynamic recrystallization (DRX) occurred at larger strains, and it was showed that nucleation occurred during straining. A criterion for DRX to occur, based on the evolution of Zener-Hollomon parameter during the dynamic deformation process, is proposed. Finally, DTE test was simulated using the modified Rusinek-Klepaczko constitutive model incorporating a model for the prediction of DRX initiation.

Cyclic Strain Resistance, Stress Response, Fatigue Life, and Fracture Behavior of High Strength Low Alloy Steel 300 M

Science.gov (United States)

Manigandan, K.; Srivatsan, T. S.; Tammana, Deepthi; Poorgangi, Behrang; Vasudevan, Vijay K.

2014-05-01

The focus of this technical manuscript is a record of the specific role of microstructure and test specimen orientation on cyclic stress response, cyclic strain resistance, and cyclic stress versus strain response, deformation and fracture behavior of alloy steel 300 M. The cyclic strain amplitude-controlled fatigue properties of this ultra-high strength alloy steel revealed a linear trend for the variation of log elastic strain amplitude with log reversals-to-failure, and log plastic strain amplitude with log reversals-to-failure for both longitudinal and transverse orientations. Test specimens of the longitudinal orientation showed only a marginal improvement over the transverse orientation at equivalent values of plastic strain amplitude. Cyclic stress response revealed a combination of initial hardening for the first few cycles followed by gradual softening for a large portion of fatigue life before culminating in rapid softening prior to catastrophic failure by fracture. Fracture characteristics of test specimens of this alloy steel were different at both the macroscopic and fine microscopic levels over the entire range of cyclic strain amplitudes examined. Both macroscopic and fine microscopic observations revealed fracture to be a combination of both brittle and ductile mechanisms. The underlying mechanisms governing stress response, deformation characteristics, fatigue life, and final fracture behavior are presented and discussed in light of the competing and mutually interactive influences of test specimen orientation, intrinsic microstructural effects, deformation characteristics of the microstructural constituents, cyclic strain amplitude, and response stress.

Microbial occurrence in bentonite-based buffer materials of a final disposal site for low level radioactive waste in Taiwan

International Nuclear Information System (INIS)

Chou Fongin; Chen Tzungyuang; Li Chiachin; Wen Hsiaowei

2011-01-01

This research addresses the potential of microbial implications in bentonite for use as a buffer and backfill material in final disposal site for low-level radioactive waste (LLRW) in Taiwan, where has a special island-type climate. Microbe activities naturally present in this site were analyzed, and buffer materials (BM) consisted of 100%, 70% or 50% bentonite were prepared for laboratory studies. A total of 39 microbial strains were isolated, and the predominant strains included four bacterial, one yeast and four fungal strains. Growth inhibition was not detected in any tested strain cultured in a radiation field with a dose rate of 0.2 Gy/h. Most of the isolated strains grew under a dose rate of 1.4 Gy/h. The D 10 values of the tested strains ranged from 0.16 to 2.05 kGy. The mycelia of tested fungal strains could spread over 5 cm during six months of inoculation in BM. The spreading activity of the tested bacteria was less than that of the fungi. Moreover, biofilms were observed on the surfaces of the BM. Since a large and diverse population of microbes is present in Taiwan, microbes may contribute to the mobilization of radionuclides in the disposal site. (author)

Innovative improvements of thermal response tests - Final report

Energy Technology Data Exchange (ETDEWEB)

Poppei, J.; Schwarz, R. [AF-Colenco Ltd, Baden (Switzerland); Peron, H.; Silvani, C; Steinmann, G.; Laloui, L. [Swiss Federal Institute of Technology, Laboratoire de Mecanique des Sols, Lausanne (Switzerland); Wagner, R.; Lochbuehler, T.; Rohner, E. [Geowatt AG, Zuerich (Switzerland)

2008-12-15

This illustrated final report for Swiss Federal Office of Energy (SFOE) takes a look at innovative improvements to thermal response tests that are used to investigate the thermo-physical properties of the ground for the purpose of dimensioning borehole heat exchangers. Recent technical developments in the borehole investigation tools area provide a promising prerequisite for improved estimates of thermal conductivity. A mini-module developed at the Swiss Federal Institute of Technology EPFL which is suitable for fast and flexible thermal response testing is discussed as is a wireless miniature data logger for continuous temperature recordings in borehole heat exchangers up to a depth of 350 m. This allows high-resolution vertical temperature profiling in boreholes. International state-of-the-art methods are reviewed. The adaptations to the analytical methods necessary for the effective application of these tools are discussed and numerical methods available are looked at. The testing of the methods developed and their results are discussed, as is the influence of ground-water flow.

Mead production: selection and characterization assays of Saccharomyces cerevisiae strains.

Science.gov (United States)

Pereira, Ana Paula; Dias, Teresa; Andrade, João; Ramalhosa, Elsa; Estevinho, Letícia M

2009-08-01

Mead is a traditional drink, which results from the alcoholic fermentation of diluted honey carried out by yeasts. However, when it is produced in a homemade way, mead producers find several problems, namely, the lack of uniformity in the final product, delayed and arrested fermentations, and the production of "off-flavours" by the yeasts. These problems are usually associated with the inability of yeast strains to respond and adapt to unfavourable and stressful growth conditions. The main objectives of this work were to evaluate the capacity of Saccharomyces cerevisiae strains, isolated from honey of the Trás-os-Montes (Northeast Portugal), to produce mead. Five strains from honey, as well as one laboratory strain and one commercial wine strain, were evaluated in terms of their fermentation performance under ethanol, sulphur dioxide and osmotic stress. All the strains showed similar behaviour in these conditions. Two yeasts strains isolated from honey and the commercial wine strain were further tested for mead production, using two different honey (a dark and a light honey), enriched with two supplements (one commercial and one developed by the research team), as fermentation media. The results obtained in this work show that S. cerevisiae strains isolated from honey, are appropriate for mead production. However it is of extreme importance to take into account the characteristics of the honey, and supplements used in the fermentation medium formulation, in order to achieve the best results in mead production.

Isolation, identification and characterization of regional indigenous Saccharomyces cerevisiae strains

Directory of Open Access Journals (Sweden)

Hana Šuranská

2016-03-01

Full Text Available Abstract In the present work we isolated and identified various indigenous Saccharomyces cerevisiae strains and screened them for the selected oenological properties. These S. cerevisiae strains were isolated from berries and spontaneously fermented musts. The grape berries (Sauvignon blanc and Pinot noir were grown under the integrated and organic mode of farming in the South Moravia (Czech Republic wine region. Modern genotyping techniques such as PCR-fingerprinting and interdelta PCR typing were employed to differentiate among indigenous S. cerevisiae strains. This combination of the methods provides a rapid and relatively simple approach for identification of yeast of S. cerevisiae at strain level. In total, 120 isolates were identified and grouped by molecular approaches and 45 of the representative strains were tested for selected important oenological properties including ethanol, sulfur dioxide and osmotic stress tolerance, intensity of flocculation and desirable enzymatic activities. Their ability to produce and utilize acetic/malic acid was examined as well; in addition, H2S production as an undesirable property was screened. The oenological characteristics of indigenous isolates were compared to a commercially available S. cerevisiae BS6 strain, which is commonly used as the starter culture. Finally, some indigenous strains coming from organically treated grape berries were chosen for their promising oenological properties and these strains will be used as the starter culture, because application of a selected indigenous S. cerevisiae strain can enhance the regional character of the wines.

Finite Element Verification of Non-Homogeneous Strain and Stress Fields during Composite Material Testing

DEFF Research Database (Denmark)

Mikkelsen, Lars Pilgaard

2015-01-01

Uni-directional glass fiber reinforced polymers play a central role in the task increasing the length of wind turbines blades and thereby lowering the cost of energy from wind turbine installations. During this, optimizing the mechanical performance regarding material stiffness, compression...... strength and fatigue performance is essential. Nevertheless, testing composites includes some challenges regarding stiffness determination using conventional strain gauges and achieving correct material failure unaffected by the gripping region during fatigue testing. Challenges, which in the present study......, has been addressed using the finite element method. During this, a verification of experimental observations, a deeper understanding on the test coupon loading and thereby improved test methods has been achieved....

OPTIMIZATION OF ENNIATINS PRODUCTION BY AN ENDOPHYTIC STRAIN FUSARIUM DIMERUM

Directory of Open Access Journals (Sweden)

Eva Buchtová

2014-10-01

Full Text Available The goal of this study was to find suitable composition of cultivation media for enniatin production by isolated endophytic strain Fusarium dimerum. In order to find optimal cultivation media, mono- and di- saccharides, complex nitrogen sources and L-amino acids directed biosynthesis of enniatins were tested. Submerged cultivation experiments were carried out in cultivation flasks. Most promising medium for enniatin accumulation contained fructose, malt extract and peptone for bacteriology. Finally, quite expensive carbon source fructose was replaced by more available syrups. Optimization resulted in 4-times elevated enniatin biosynthesis by metabolites production microorganism. Moreover, this is the strain obtained from Magnolia soulangeana, which has similar metabolites spectrum as the isolated Fusarium dimerum. Comparison of these results with published ones revealed that this endophyte is a potential strain for enniatins biosynthesis in submerged cultivation in which the maximum accumulation 1.27 g.L-1 of enniatin in culture medium was reached in a short period (96 h. The results proved that the endophytic strain F. dimerum may potentially be applied for efficient production of bioactive enniatins.

Quantitative description of a high Jc Nb-Ti superconductor during its final optimization strain. I. Microstructure, Tc, Hc2, and resistivity

International Nuclear Information System (INIS)

Meingast, C.; Lee, P.J.; Larbalestier, D.C.

1989-01-01

A most important step in the critical current density (J c ) optimization of Nb-Ti is the large final drawing strain, in which α-Ti precipitates, initially approximately equiaxed and 100--200 nm in diameter, are drawn into ribbons, whose thickness (1--2 nm) is less than the superconducting coherence length [ξ (4.2 K)∼5 nm]. Using transmission electron microscopy, the precipitate thickness, spacing, cross-sectional area, and circumference were measured over the whole final drawing strain range. Each of these parameters was found to have a simple power dependence on the wire diameter. T c , H c2 , and the resistivity (ρ n ) were also change considerably during the refinement of the precipitates. Directly after precipitation, T c increased, and (dH c2 /dT) T c and ρ n were reduced from the single-phase values. Drawing the wire returned these parameters to their single-phase values, as the precipitate thickness was reduced to less than ξ. This observation explains a long-standing peculiarity in this system, namely that the optimum H c2 of high J c conductors occurs for a composition close to Nb 46 wt.% Ti, even when the precipitation of 18 vol % of α-Ti shifts the matrix composition to a Nb-rich composition of theoretically lower H c2

The strains recommended for use in the bacterial reverse mutation test (OECD guideline 471) can be certified as non-genetically modified organisms.

Science.gov (United States)

Sugiyama, Kei-Ichi; Yamada, Masami; Awogi, Takumi; Hakura, Atsushi

2016-01-01

The bacterial reverse mutation test, commonly called Ames test, is used worldwide. In Japan, the genetically modified organisms (GMOs) are regulated under the Cartagena Domestic Law, and organisms obtained by self-cloning and/or natural occurrence would be exempted from the law case by case. The strains of Salmonella typhimurium and Escherichia coli recommended for use in the bacterial reverse mutation test (OECD guideline 471), have been considered as non-GMOs because they can be constructed by self-cloning or naturally occurring bacterial strains, or do not disturb the biological diversity. The present article explains the reasons why these tester strains should be classified as non-GMOs.

Standard practice for slow strain rate testing to evaluate the susceptibility of metallic materials to environmentally assisted cracking

CERN Document Server

American Society for Testing and Materials. Philadelphia

2000-01-01

1.1 This practice covers procedures for the design, preparation, and use of axially loaded, tension test specimens and fatigue pre-cracked (fracture mechanics) specimens for use in slow strain rate (SSR) tests to investigate the resistance of metallic materials to environmentally assisted cracking (EAC). While some investigators utilize SSR test techniques in combination with cyclic or fatigue loading, no attempt has been made to incorporate such techniques into this practice. 1.2 Slow strain rate testing is applicable to the evaluation of a wide variety of metallic materials in test environments which simulate aqueous, nonaqueous, and gaseous service environments over a wide range of temperatures and pressures that may cause EAC of susceptible materials. 1.3 The primary use of this practice is to furnish accepted procedures for the accelerated testing of the resistance of metallic materials to EAC under various environmental conditions. In many cases, the initiation of EAC is accelerated through the applic...

Differentiation of Staphylococcus aureus from freshly slaughtered poultry and strains 'endemic' to processing plants by biochemical and physiological tests.

Science.gov (United States)

Mead, G C; Norris, A P; Bratchell, N

1989-02-01

A comparison was made of 27 'endemic' strains of Staphylococcus aureus and 35 strains from freshly slaughtered birds, isolated at five commercial slaughterhouses processing chickens or turkeys. Of 112 biochemical and physiological tests used, 74 gave results which differed among the strains. Cluster analysis revealed several distinct groupings which were influenced by strain type, processing plant and bird origin; these included a single group at the 72% level of similarity containing most of the 'endemic' strains. In comparison with strains from freshly slaughtered birds, a higher proportion of 'endemic' strains produced fibrinolysin, alpha-glucosidase and urease and were beta-haemolytic on sheep-blood agar. The 'endemic' type also showed a greater tendency to coagulate human but not bovine plasma, and to produce mucoid growth and clumping. The last two properties, relevant to colonization of processing equipment, were less evident in heart infusion broth than in richer media or process water collected during defeathering of the birds.

Five challenges in modelling interacting strain dynamics

DEFF Research Database (Denmark)

Wikramaratna, Paul S; Kurcharski, Adam; Gupta, Sunetra

2015-01-01

population models. Next we consider the nature of so-called “strain space”. We describe two key types of host heterogeneities, and explain how models could help generate a better understanding of their effects. Finally, for diseases with many strains, we consider the challenge of modelling how immunity...

Resimulation of noise: a precision estimator for least square error curve-fitting tested for axial strain time constant imaging

Science.gov (United States)

Nair, S. P.; Righetti, R.

2015-05-01

Recent elastography techniques focus on imaging information on properties of materials which can be modeled as viscoelastic or poroelastic. These techniques often require the fitting of temporal strain data, acquired from either a creep or stress-relaxation experiment to a mathematical model using least square error (LSE) parameter estimation. It is known that the strain versus time relationships for tissues undergoing creep compression have a non-linear relationship. In non-linear cases, devising a measure of estimate reliability can be challenging. In this article, we have developed and tested a method to provide non linear LSE parameter estimate reliability: which we called Resimulation of Noise (RoN). RoN provides a measure of reliability by estimating the spread of parameter estimates from a single experiment realization. We have tested RoN specifically for the case of axial strain time constant parameter estimation in poroelastic media. Our tests show that the RoN estimated precision has a linear relationship to the actual precision of the LSE estimator. We have also compared results from the RoN derived measure of reliability against a commonly used reliability measure: the correlation coefficient (CorrCoeff). Our results show that CorrCoeff is a poor measure of estimate reliability for non-linear LSE parameter estimation. While the RoN is specifically tested only for axial strain time constant imaging, a general algorithm is provided for use in all LSE parameter estimation.

A new strain gage method for measuring the contractile strain ratio of Zircaloy tubing

International Nuclear Information System (INIS)

Hwang, S.K.; Sabol, G.P.

1988-01-01

An improved strain gage method for determining the contractile strain ratio (CSR) of Zircaloy tubing was developed. The new method consists of a number of load-unload cyclings at approximately 0.2% plastic strain interval. With this method the CSR of Zircaloy-4 tubing could be determined accurately because it was possible to separate the plastic strains from the elastic strain involvement. The CSR values determined by use of the new method were in good agreement with those calculated from conventional post-test manual measurements. The CSR of the tubing was found to decrease with the amount of deformation during testing because of uneven plastic flow in the gage section. A new technique of inscribing gage marks by use of a YAG laser is discussed. (orig.)

Strain gauge validation experiments for the Sandia 34-meter VAWT (Vertical Axis Wind Turbine) test bed

Science.gov (United States)

Sutherland, Herbert J.

1988-08-01

Sandia National Laboratories has erected a research oriented, 34- meter diameter, Darrieus vertical axis wind turbine near Bushland, Texas. This machine, designated the Sandia 34-m VAWT Test Bed, is equipped with a large array of strain gauges that have been placed at critical positions about the blades. This manuscript details a series of four-point bend experiments that were conducted to validate the output of the blade strain gauge circuits. The output of a particular gauge circuit is validated by comparing its output to equivalent gauge circuits (in this stress state) and to theoretical predictions. With only a few exceptions, the difference between measured and predicted strain values for a gauge circuit was found to be of the order of the estimated repeatability for the measurement system.

Slip weakening, strain and short-termpreseismic disturbances

Directory of Open Access Journals (Sweden)

V. A. Morgounov

2004-06-01

Full Text Available The problem of short-term earthquake precursors is discussed. In contrast to the increasing number of reports on short-lived precursors of various types, direct strain measurements cannot detect clearly expressed preseismic anomalies, as follows from the aseismic nucleation mechanism. Based on previously published data and the assumption that the attenuation of the stress-strain field is proportional to r- 3, a possible scenario of the final stage of earthquake nucleation process is proposed on the basis of the slip weakening mechanism in the source and the associated mosaic pattern of precursors on the Earth?s surface. The formulas for estimating the maximum distance of precursor detection and minimum duration of the final stage of inelastic deformation preceding brittle failure of rocks are derived. The data of electromagnetic precursors are interpreted in terms of a skin-layer model. A considerable increase in strain rates at the final stage of the earthquake nucleation provides an opportunity to explain teleseismic effects before strong earthquakes in terms of normalized epicenter distance. The modeling results are compared with in situ observations.

Repeated Strains, Social Control, Social Learning, and Delinquency: Testing an Integrated Model of General Strain Theory in China

Science.gov (United States)

Bao, Wan-Ning; Haas, Ain; Chen, Xiaojin; Pi, Yijun

2014-01-01

In Agnew's general strain theory, repeated strains can generate crime and delinquency by reducing social control and fostering social learning of crime. Using a sample of 615 middle-and high-school students in China, this study examines how social control and social learning variables mediate the effect of repeated strains in school and at home on…

A fiber optics sensor for strain and stress management in superconducting accelerator magnets

International Nuclear Information System (INIS)

van Oort, J.M.; ten Kate, H.H.J.

1993-01-01

A novel cryogenic interferometric fiber optics sensor for the measurement of strain and stress in the coil windings of superconducting accelerator magnets is described. The sensor can operate with two different readout sources, monochromatic laser light and white light respectively. The sensor head is built up as an extrinsic Fabry-Perot interferometer formed with two cleaved fiber surfaces, and can be mounted in several configurations. When read with laser light, the sensor is an extremely sensitive relative strain or temperature detector. When read with white light the absolute strain and pressure can be measured. Results are presented of tests in several configurations at 77 K and 4.2 K, both for the relative and absolute readout method. Finally, the possible use for quench localization using the temperature sensitivity is described

Ductility and failure behaviour of both unirradiated and irradiated zircaloy-4 cladding using plane strain tensile specimens

International Nuclear Information System (INIS)

Carassou, S.; Le Saux, M.; Pizzanelli, J.P.; Rabouille, O.; Averty, X.; Poussard, C.; Cazalis, B.; Desquines, J.; Bernaudat, C.

2010-01-01

In this work, eight PST (Plan Strain Tensile) tests machined from a Zircaloy-4 (Zy-4) cladding irradiated up to 5 annual cycles have been performed at 280, 350 and 480 Celsius degrees. The specimen displacements during the tests were filmed and digitally recorded to allow the use of a Digital Image Correlation (DIC) analysis technique to experimentally determine the local strains on the outer surface of the specimens. The plane strain conditions have been verified and prevail over a wide area between the notches of the specimen, as expected from full 3D FE numerical analysis performed in support of the tests. For the first time, the location of the onset of fracture for this geometry on irradiated material has been experimentally observed: at 280 C.degrees, crack initiates in the vicinity of the notches, in an area where plane strain conditions are not fulfilled, and for a local circumferential strain value of about 5%. At 350 C. degrees and 480 C. degrees, cracks initiate at a location where plane strain conditions prevail, for circumferential strain values respectively close to 10% and greater than 50%. These results have been compared to results obtained previously by similar test on fresh and hydrided material, as well as tests performed as support to the study. At 350 C. degrees, the homogeneous 700 ppm hydrided Zy-4 and the Zy-4 irradiated during 5 annual cycles exhibit similar fracture behaviour, for both fracture hoop strain values (10%) and fracture mode (through-wall slant fracture). For the irradiated material, it has clearly been established that at 350 C. degrees, a brittle fracture occurs at the outer surface in the hydride rim. The crack propagates subsequently toward the inner surface and the notches, where final fracture occurs

Final focus test beam alignment: A draft proposal

International Nuclear Information System (INIS)

Fischer, G.E.; Ruland, R.E.

1989-03-01

The Final Focus Test Beam is a transport line designed to transmit 50 GeV electron beams of SLC emittance (3 x 10 -10 radian-meters) straight through the central arm of the Beam Switchyard (BSY C line) with a final focus point out in the Research Yard but relatively near the end of the switchyard tunnel. The hardware, methods and procedures outlined in this proposal are dedicated to measuring the placement of mechanical objects with respect to certain defined geometric axes. We wish to emphasize that the very difficult problems of locating the effective magnetic axes of focusing elements, the effective electrical center of beam position monitors and even the effective axis of the incident beam relative to mechanical reference surfaces is outside the scope of this work. Further, this proposal is restricted to the act of measurement and does not consider the vital task of on-line mechanical repositioning of elements that will, in likelihood, be called upon during operation of the system. 16 refs., 16 figs., 4 tabs

Temperature buffer test. Final report

International Nuclear Information System (INIS)

Aakesson, Mattias

2012-04-01

The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aspo HRL. It was installed during the spring of 2003. Two steel heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by rings of compacted Wyoming bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report is the final report and a summary of all work performed within the TBT project. The design and the installation of the different components are summarized: the depositions hole, the heating system, the bentonite blocks with emphasis on the initial density and water content in these, the filling of slots with sand or pellets, the retaining construction with the plug, lid and nine anchor cables, the artificial saturation system, and finally the instrumentation. An overview of the operational conditions is presented: the power output from heaters, which was 1,500 W (and also 1,600 W) from each heater during the first ∼1,700 days, and then changed to 1,000 and 2,000 W, for the upper and lower heater respectively, during the last ∼600 days. From the start, the bentonite was hydrated with a groundwater from a nearby bore-hole, but this groundwater was replaced with de-ionized water from day ∼1,500, due to the high flow resistance of the injections points in the filter, which implied that a high filter pressure couldn't be sustained. The sand shield around the upper heater was hydrated from day ∼1,500 to day ∼1,800. The sensors data concerning

Temperature buffer test. Final report

Energy Technology Data Exchange (ETDEWEB)

Aakesson, Mattias [Clay Technology AB, Lund (Sweden)

2012-04-15

The Temperature Buffer Test (TBT) is a joint project between SKB/ANDRA and supported by ENRESA (modelling) and DBE (instrumentation), which aims at improving the understanding and to model the thermo-hydro-mechanical behavior of buffers made of swelling clay submitted to high temperatures (over 100 deg C) during the water saturation process. The test has been carried out in a KBS-3 deposition hole at Aspo HRL. It was installed during the spring of 2003. Two steel heaters (3 m long, 0.6 m diameter) and two buffer arrangements have been investigated: the lower heater was surrounded by rings of compacted Wyoming bentonite only, whereas the upper heater was surrounded by a composite barrier, with a sand shield between the heater and the bentonite. The test was dismantled and sampled during the winter of 2009/2010. This report is the final report and a summary of all work performed within the TBT project. The design and the installation of the different components are summarized: the depositions hole, the heating system, the bentonite blocks with emphasis on the initial density and water content in these, the filling of slots with sand or pellets, the retaining construction with the plug, lid and nine anchor cables, the artificial saturation system, and finally the instrumentation. An overview of the operational conditions is presented: the power output from heaters, which was 1,500 W (and also 1,600 W) from each heater during the first {approx}1,700 days, and then changed to 1,000 and 2,000 W, for the upper and lower heater respectively, during the last {approx}600 days. From the start, the bentonite was hydrated with a groundwater from a nearby bore-hole, but this groundwater was replaced with de-ionized water from day {approx}1,500, due to the high flow resistance of the injections points in the filter, which implied that a high filter pressure couldn't be sustained. The sand shield around the upper heater was hydrated from day {approx}1,500 to day {approx}1

Haldane model under nonuniform strain

Science.gov (United States)

Ho, Yen-Hung; Castro, Eduardo V.; Cazalilla, Miguel A.

2017-10-01

We study the Haldane model under strain using a tight-binding approach, and compare the obtained results with the continuum-limit approximation. As in graphene, nonuniform strain leads to a time-reversal preserving pseudomagnetic field that induces (pseudo-)Landau levels. Unlike a real magnetic field, strain lifts the degeneracy of the zeroth pseudo-Landau levels at different valleys. Moreover, for the zigzag edge under uniaxial strain, strain removes the degeneracy within the pseudo-Landau levels by inducing a tilt in their energy dispersion. The latter arises from next-to-leading order corrections to the continuum-limit Hamiltonian, which are absent for a real magnetic field. We show that, for the lowest pseudo-Landau levels in the Haldane model, the dominant contribution to the tilt is different from graphene. In addition, although strain does not strongly modify the dispersion of the edge states, their interplay with the pseudo-Landau levels is different for the armchair and zigzag ribbons. Finally, we study the effect of strain in the band structure of the Haldane model at the critical point of the topological transition, thus shedding light on the interplay between nontrivial topology and strain in quantum anomalous Hall systems.

Comparison of methods for in vitro testing of susceptibility of porcine Mycoplasma species to antimicrobial agents.

Science.gov (United States)

Ter Laak, E A; Pijpers, A; Noordergraaf, J H; Schoevers, E C; Verheijden, J H

1991-02-01

The MICs of 18 antimicrobial agents used against strains of three porcine Mycoplasma species were determined by a serial broth dilution method. Twenty field strains of M. hyorhinis, ten field strains of M. hyopneumoniae, six field strains of M. flocculare, and the type strains of these species were tested. Twelve field strains and the type strain of M. hyorhinis were also tested by an agar dilution method. Tests were read at various time points. When the broth dilution method was used, the final MIC had to be read 2 days after color changes had stopped. MICs of tetracycline, oxytetracycline, doxycycline, and minocycline were low for the three Mycoplasma species tested. MICs of chlortetracycline were 8 to 16 times higher than MICs of the other tetracyclines. Spiramycin, tylosin, kitasamycin, spectinomycin, tiamulin, lincomycin, and clindamycin were effective against all strains of M. hyorhinis and M. hyopneumoniae. The quinolones were highly effective against M. hyopneumoniae but less effective against M. hyorhinis. The susceptibility patterns for M. hyopneumoniae and M. flocculare were similar.

Segregation of genes from donor strain during the production of recombinant congenic strains.

Science.gov (United States)

van Zutphen, L F; Den Bieman, M; Lankhorst, A; Demant, P

1991-07-01

Recombinant congenic strains (RCS) constitute a set of inbred strains which are designed to dissect the genetic control of multigenic traits, such as tumour susceptibility or disease resistance. Each RCS contains a small fraction of the genome of a common donor strain, while the majority of genes stem from a common background strain. We tested at two stages of the inbreeding process in 20 RCS, derived from BALB/cHeA and STS/A, to see whether alleles from the STS/A donor strain are distributed over the RCS in a ratio as would theoretically be expected. Four marker genes (Pep-3; Pgm-1; Gpi-1 and Es-3) located at 4 different chromosomes were selected and the allelic distribution was tested after 3-4 and after 12 generations of inbreeding. The data obtained do not significantly deviate from the expected pattern, thus supporting the validity of the concept of RCS.

Strain measurement on a compact nuclear reactor steam generator

International Nuclear Information System (INIS)

Scaldaferri, Denis Henrique Bianchi; Gomes, Paulo de Tarso Vida; Mansur, Tanius Rodrigues; Pozzo, Renato del; Mola, Jairo

2011-01-01

This work presents the strain measurement procedures applied to a compact nuclear reactor steam generator, during a hydrostatic test, using strain gage technology. The test was divided in two steps: primary side test and secondary side test. In the primary side test twelve points for strain measurement using rectangular rosettes, three points (two external and one internal) for temperature measurement using special strain gages and one point for pressure measurement using a pressure transducer were monitored. In the secondary side test 18 points for strain measurement using rectangular rosettes, four points (two external and two internal) for temperature measurement using special strain gages and one point for pressure measurement using a pressure transducer were monitored. The measurement points on both internal and external pressurizer walls were established from pre-calculated stress distribution by means of numerical approach (finite elements modeling). Strain values using a quarter Wheatstone bridge circuit were obtained. Stress values, from experimental strain were determined, and to numerical calculation results were compared. (author)

Finite element modelling of fibre Bragg grating strain sensors and experimental validation

Science.gov (United States)

Malik, Shoaib A.; Mahendran, Ramani S.; Harris, Dee; Paget, Mark; Pandita, Surya D.; Machavaram, Venkata R.; Collins, David; Burns, Jonathan M.; Wang, Liwei; Fernando, Gerard F.

2009-03-01

Fibre Bragg grating (FBG) sensors continue to be used extensively for monitoring strain and temperature in and on engineering materials and structures. Previous researchers have also developed analytical models to predict the loadtransfer characteristics of FBG sensors as a function of applied strain. The general properties of the coating or adhesive that is used to surface-bond the FBG sensor to the substrate has also been modelled using finite element analysis. In this current paper, a technique was developed to surface-mount FBG sensors with a known volume and thickness of adhesive. The substrates used were aluminium dog-bone tensile test specimens. The FBG sensors were tensile tested in a series of ramp-hold sequences until failure. The reflected FBG spectra were recorded using a commercial instrument. Finite element analysis was performed to model the response of the surface-mounted FBG sensors. In the first instance, the effect of the mechanical properties of the adhesive and substrate were modelled. This was followed by modelling the volume of adhesive used to bond the FBG sensor to the substrate. Finally, the predicted values obtained via finite element modelling were correlated to the experimental results. In addition to the FBG sensors, the tensile test specimens were instrumented with surface-mounted electrical resistance strain gauges.

The Final Focus Test Beam laser referene system

International Nuclear Information System (INIS)

Bressler, V.E.; Ruland, R.E.

1993-05-01

The original design for the SLAC linac included an alignment reference system with 270 diffraction gratings situated along the 3000 meter linac. These gratings have provided SLAC with a global reference line repeatable to within 200 micro meters. For the Final Focus Test Beam, this laser system has been extended and 13 new diffraction gratings have been installed. Improvements targets and the availability of new instruments allows us to evaluate the performance of the laser reference system at the 510 micro meter level. An explanation of the system and the results of our evaluation are presented

Evaluation of susceptibility of high strength steels to delayed fracture by using cyclic corrosion test and slow strain rate test

International Nuclear Information System (INIS)

Li Songjie; Zhang Zuogui; Akiyama, Eiji; Tsuzaki, Kaneaki; Zhang Boping

2010-01-01

To evaluate susceptibilities of high strength steels to delayed fracture, slow strain rate tests (SSRT) of notched bar specimens of AISI 4135 with tensile strengths of 1300 and 1500 MPa and boron-bearing steel with 1300 MPa have been performed after cyclic corrosion test (CCT). During SSRT the humidity around the specimen was kept high to keep absorbed diffusible hydrogen. The fracture stresses of AISI 4135 steels decreased with increment of diffusible hydrogen content which increased with CCT cycles. Their delayed fracture susceptibilities could be successfully evaluated in consideration of both influence of hydrogen content on mechanical property and hydrogen entry.

Evaluation of susceptibility of high strength steels to delayed fracture by using cyclic corrosion test and slow strain rate test

Energy Technology Data Exchange (ETDEWEB)

Li Songjie [School of Materials Science and Engineering, University of Science and Technology Beijing, No. 30 Xueyuan Road, Hidian Zone, Beijing 100083 (China); Structural Metals Center, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Zhang Zuogui [Structural Metals Center, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Akiyama, Eiji [Structural Metals Center, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan)], E-mail: AKIYAMA.Eiji@nims.go.jp; Tsuzaki, Kaneaki [Structural Metals Center, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba, Ibaraki 305-0047 (Japan); Zhang Boping [School of Materials Science and Engineering, University of Science and Technology Beijing, No. 30 Xueyuan Road, Hidian Zone, Beijing 100083 (China)

2010-05-15

To evaluate susceptibilities of high strength steels to delayed fracture, slow strain rate tests (SSRT) of notched bar specimens of AISI 4135 with tensile strengths of 1300 and 1500 MPa and boron-bearing steel with 1300 MPa have been performed after cyclic corrosion test (CCT). During SSRT the humidity around the specimen was kept high to keep absorbed diffusible hydrogen. The fracture stresses of AISI 4135 steels decreased with increment of diffusible hydrogen content which increased with CCT cycles. Their delayed fracture susceptibilities could be successfully evaluated in consideration of both influence of hydrogen content on mechanical property and hydrogen entry.

Finite Element Analysis and Test Results Comparison for the Hybrid Wing Body Center Section Test Article

Science.gov (United States)

Przekop, Adam; Jegley, Dawn C.; Rouse, Marshall; Lovejoy, Andrew E.

2016-01-01

This report documents the comparison of test measurements and predictive finite element analysis results for a hybrid wing body center section test article. The testing and analysis efforts were part of the Airframe Technology subproject within the NASA Environmentally Responsible Aviation project. Test results include full field displacement measurements obtained from digital image correlation systems and discrete strain measurements obtained using both unidirectional and rosette resistive gauges. Most significant results are presented for the critical five load cases exercised during the test. Final test to failure after inflicting severe damage to the test article is also documented. Overall, good comparison between predicted and actual behavior of the test article is found.

Fracto-mechanoluminescent light emission of EuD4TEA-PDMS composites subjected to high strain-rate compressive loading

Science.gov (United States)

Ryu, Donghyeon; Castaño, Nicolas; Bhakta, Raj; Kimberley, Jamie

2017-08-01

The objective of this study is to understand light emission characteristics of fracto-mechanoluminescent (FML) europium tetrakis(dibenzoylmethide)-triethylammonium (EuD4TEA) crystals under high strain-rate compressive loading. As a sensing material that can play a pivotal role for the self-powered impact sensor technology, it is important to understand transformative light emission characteristics of the FML EuD4TEA crystals under high strain-rate compressive loading. First, EuD4TEA crystals were synthesized and embedded into polydimethylsiloxane (PDMS) elastomer to fabricate EuD4TEA-PDMS composite test specimens. Second, the prepared EuD4TEA-PDMS composites were tested using the modified Kolsky bar setup equipped with a high-speed camera. Third, FML light emission was captured to yield 12 bit grayscale video footage, which was processed to quantify the FML light emission. Finally, quantitative parameters were generated by taking into account pixel values and population of pixels of the 12 bit grayscale images to represent FML light intensity. The FML light intensity was correlated with high strain-rate compressive strain and strain rate to understand the FML light emission characteristics under high strain-rate compressive loading that can result from impact occurrences.

Failure strains and proposed limit strains for an reactor pressure vessel under severe accident conditions

International Nuclear Information System (INIS)

Krieg, R.

2005-01-01

The local failure strains of essential design elements of a reactor vessel are investigated. The size influence of the structure is of special interest. Typical severe accident conditions including elevated temperatures and dynamic loads are considered. The main part of work consists of test families with specimens under uniaxial and biaxial load. Within one test family the specimen geometry and the load conditions are similar, but the size is varied up to reactor dimensions. Special attention is given to geometries with a hole or a notch causing non-uniform stress and strain distributions typical for the reactor vessel. A key problem is to determine the local failure strain. Here suitable methods had to be developed including the so-called 'vanishing gap method', and the 'forging die method'. They are based on post-test geometrical measurements of the fracture surfaces and reconstructions of the related strain fields using finite element models. The results indicate that stresses versus dimensionless deformations are approximately size independent up to failure for specimens of similar geometry under similar load conditions. Local failure strains could be determined. The values are rather high and size dependent. Statistical evaluation allow the proposal of limit strains which are also size dependent. If these limit strains are not exceeded, the structures will not fracture

Deformed Shape Calculation of a Full-Scale Wing Using Fiber Optic Strain Data from a Ground Loads Test

Science.gov (United States)

Jutte, Christine V.; Ko, William L.; Stephens, Craig A.; Bakalyar, John A.; Richards, W. Lance

2011-01-01

A ground loads test of a full-scale wing (175-ft span) was conducted using a fiber optic strain-sensing system to obtain distributed surface strain data. These data were input into previously developed deformed shape equations to calculate the wing s bending and twist deformation. A photogrammetry system measured actual shape deformation. The wing deflections reached 100 percent of the positive design limit load (equivalent to 3 g) and 97 percent of the negative design limit load (equivalent to -1 g). The calculated wing bending results were in excellent agreement with the actual bending; tip deflections were within +/- 2.7 in. (out of 155-in. max deflection) for 91 percent of the load steps. Experimental testing revealed valuable opportunities for improving the deformed shape equations robustness to real world (not perfect) strain data, which previous analytical testing did not detect. These improvements, which include filtering methods developed in this work, minimize errors due to numerical anomalies discovered in the remaining 9 percent of the load steps. As a result, all load steps attained +/- 2.7 in. accuracy. Wing twist results were very sensitive to errors in bending and require further development. A sensitivity analysis and recommendations for fiber implementation practices, along with, effective filtering methods are included

Strain rate dependent tensile behavior of advanced high strength steels: Experiment and constitutive modeling

International Nuclear Information System (INIS)

Kim, Ji-Hoon; Kim, Daeyong; Han, Heung Nam; Barlat, F.; Lee, Myoung-Gyu

2013-01-01

High strain rate tensile tests were conducted for three advanced high strength steels: DP780, DP980 and TRIP780. A high strain rate tensile test machine was used for applying the strain rate ranging from 0.1/s to 500/s. Details of the measured stress–strain responses were comparatively analyzed for the DP780 and TRIP780 steels which show similar microstructural feature and ultimate tensile strength, but different strengthening mechanisms. The experimental observations included: usual strain rate dependent plastic flow stress behavior in terms of the yield stress (YS), the ultimate tensile strength (UTS), the uniform elongation (UE) and the total elongation (TE) which were observed for the three materials. But, higher strain hardening rate at early plastic strain under quasi-static condition than that of some increased strain rates was featured for TRIP780 steel, which might result from more active transformation during deformation with lower velocity. The uniform elongation that explains the onset of instability and the total elongation were larger in case of TRIP steel than the DP steel for the whole strain rate range, but interestingly the fracture strain measured by the reduction of area (RA) method showed that the TRIP steel has lower values than DP steel. The fractographs using scanning electron microscopy (SEM) at the fractured surfaces were analyzed to relate measured fracture strain and the microstructural difference of the two materials during the process of fracture under various strain rates. Finally, constitutive modeling for the plastic flow stresses under various strain rates was provided in this study. The proposed constitutive law could represent both Hollomon-like and Voce-like hardening laws and the ratio between the two hardening types was efficiently controlled as a function of strain rate. The new strength model was validated successfully under various strain rates for several grades of steels such as mild steels, DP780, TRIP780, DP980 steels.

FIND Tuberculosis Strain Bank: a Resource for Researchers and Developers Working on Tests To Detect Mycobacterium tuberculosis and Related Drug Resistance.

Science.gov (United States)

Tessema, Belay; Nabeta, Pamela; Valli, Eloise; Albertini, Audrey; Collantes, Jimena; Lan, Nguyen Huu; Romancenco, Elena; Tukavdze, Nestani; Denkinger, Claudia M; Dolinger, David L

2017-04-01

The spread of multidrug-resistant (MDR) tuberculosis (TB) and extensively drug-resistant (XDR) TB hampers global efforts in the fight against tuberculosis. To enhance the development and evaluation of diagnostic tests quickly and efficiently, well-characterized strains and samples from drug-resistant tuberculosis patients are necessary. In this project, the Foundation for Innovative New Diagnostics (FIND) has focused on the collection, characterization, and storage of such well-characterized reference materials and making them available to researchers and developers. The collection is being conducted at multiple centers in Southeast Asia, South America, Eastern Europe, and soon the sub-Saharan Africa regions. Strains are characterized for their phenotypic resistances and MICs to first-line drugs (FLDs) and second-line drugs (SLDs) using the automated MGIT 960 system following validated procedures and WHO criteria. Analysis of resistance-associated mutations is done by whole-genome sequencing (WGS) using the Illumina NextSeq system. Mycobacterial interspersed repetitive-unit-variable-number tandem-repeat analysis and WGS are used to determine strain lineages. All strains are maintained frozen at -80°C ± 10°C as distinct mother and daughter lots. All strains are extensively quality assured. The data presented here represent an analysis of the initial part of the collection. Currently, the bank contains 118 unique strains with extracted genomic DNA and matched sputum, serum, and plasma samples and will be expanded to a minimum of 1,000 unique strains over the next 3 years. Analysis of the current strains by phenotypic resistance testing shows 102 (86.4%), 10 (8.5%), and 6 (5.1%) MDR, XDR, and mono/poly resistant strains, respectively. Two of the strains are resistant to all 11 drugs that were phenotypically tested. WGS mutation analysis revealed FLD resistance-associated mutations in the rpoB , katG , inhA , embB , embA , and pncA genes; SLD resistance in the gyr

Suitability of Strain Gage Sensors for Integration into Smart Sport Equipment: A Golf Club Example.

Science.gov (United States)

Umek, Anton; Zhang, Yuan; Tomažič, Sašo; Kos, Anton

2017-04-21

Wearable devices and smart sport equipment are being increasingly used in amateur and professional sports. Smart sport equipment employs various sensors for detecting its state and actions. The correct choice of the most appropriate sensor(s) is of paramount importance for efficient and successful operation of sport equipment. When integrated into the sport equipment, ideal sensors are unobstructive, and do not change the functionality of the equipment. The article focuses on experiments for identification and selection of sensors that are suitable for the integration into a golf club with the final goal of their use in real time biofeedback applications. We tested two orthogonally affixed strain gage (SG) sensors, a 3-axis accelerometer, and a 3-axis gyroscope. The strain gage sensors are calibrated and validated in the laboratory environment by a highly accurate Qualisys Track Manager (QTM) optical tracking system. Field test results show that different types of golf swing and improper movement in early phases of golf swing can be detected with strain gage sensors attached to the shaft of the golf club. Thus they are suitable for biofeedback applications to help golfers to learn repetitive golf swings. It is suggested that the use of strain gage sensors can improve the golf swing technical error detection accuracy and that strain gage sensors alone are enough for basic golf swing analysis. Our final goal is to be able to acquire and analyze as many parameters of a smart golf club in real time during the entire duration of the swing. This would give us the ability to design mobile and cloud biofeedback applications with terminal or concurrent feedback that will enable us to speed-up motor skill learning in golf.

Establishing quality control ranges for antimicrobial susceptibility testing of Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus: a cornerstone to develop reference strains for Korean clinical microbiology laboratories.

Science.gov (United States)

Hong, Sung Kuk; Choi, Seung Jun; Shin, Saeam; Lee, Wonmok; Pinto, Naina; Shin, Nari; Lee, Kwangjun; Hong, Seong Geun; Kim, Young Ah; Lee, Hyukmin; Kim, Heejung; Song, Wonkeun; Lee, Sun Hwa; Yong, Dongeun; Lee, Kyungwon; Chong, Yunsop

2015-11-01

Quality control (QC) processes are being performed in the majority of clinical microbiology laboratories to ensure the performance of microbial identification and antimicrobial susceptibility testing by using ATCC strains. To obtain these ATCC strains, some inconveniences are encountered concerning the purchase cost of the strains and the shipping time required. This study was focused on constructing a database of reference strains for QC processes using domestic bacterial strains, concentrating primarily on antimicrobial susceptibility testing. Three strains (Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus) that showed legible results in preliminary testing were selected. The minimal inhibitory concentrations (MICs) and zone diameters (ZDs) of eight antimicrobials for each strain were determined according to the CLSI M23. All resulting MIC and ZD ranges included at least 95% of the data. The ZD QC ranges obtained by using the CLSI method were less than 12 mm, and the MIC QC ranges extended no more than five dilutions. This study is a preliminary attempt to construct a bank of Korean QC strains. With further studies, a positive outcome toward cost and time reduction can be anticipated.

Characterization of cracking in Strain-Hardening Cementitious Composites using the compact tension test

DEFF Research Database (Denmark)

Pereira, Eduardo B.; Fischer, Gregor; Barros, Joaquim A. O.

The characterization of the tensile behavior of strain hardening cementitious composites (SHCC) is of significant importance to the material design. In a previous work the tensile stress-crack opening response of different types of SHCC was characterized using notched specimens tested in direct...... tension, where a single crack was obtained and mechanically characterized by performing Single Crack Tension Test (SCTT). In this study the tensile behavior of SHCC materials is characterized under eccentric tensile load using the Compact Tension Test (CTT). The long edge notch placed in the rectangular...... plate specimens and the eccentrically applied tensile load create the local conditions necessary to the initiation of a single crack at the tip of the notch. Further propagation and opening of the crack in Mode I allow the assessment of the tensile load-displacement relationship. The experimental...

Growth and consumption of L-malic acid in wine-like medium by acclimated and non-acclimated cultures of Patagonian Oenococcus oeni strains.

Science.gov (United States)

Bravo-Ferrada, Bárbara Mercedes; Hollmann, Axel; Brizuela, Natalia; La Hens, Danay Valdés; Tymczyszyn, Elizabeth; Semorile, Liliana

2016-09-01

Five Oenococcus oeni strains, selected from spontaneous malolactic fermentation (MLF) of Patagonic Pinot noir wine, were assessed for their use as MLF starter cultures. After the individual evaluation of tolerance to some stress conditions, usually found in wine (pH, ethanol, SO2, and lysozyme), the behavior of the strains was analyzed in MLO broth with 14 % ethanol and pH 3.5 in order to test for the synergistic effect of high ethanol level and low pH and, finally, in a wine-like medium. Although the five strains were able to grow in MLO broth under low pH and/or high ethanol, they must be acclimated to grow in a wine-like medium. Additionally, glycosidase and tannase activities were evaluated, showing differences among the strains. The potential of the strains to ferment citrate was tested and two of the five strains showed the ability to metabolize this substrate. We did not detect the presence of genes encoding histidine, tyrosine descarboxylase, and putrescine carbamoyltransferase. All the strains tested exhibited good growth capacity and ability to consume L-malic acid in a wine-like medium after cell acclimation, and each of them showed a particular enzyme profile, which might confer different organoleptic properties to the wine.

Frequency of chest pain in primary care, diagnostic tests performed and final diagnoses.

Science.gov (United States)

Hoorweg, Beatrijs Bn; Willemsen, Robert Ta; Cleef, Lotte E; Boogaerts, Tom; Buntinx, Frank; Glatz, Jan Fc; Dinant, Geert Jan

2017-11-01

Observational study of patients with chest pain in primary care: determination of incidence, referral rate, diagnostic tests and (agreement between) working and final diagnoses. 118 general practitioners (GPs) in the Netherlands and Belgium recorded all patient contacts during  2weeks. Furthermore, patients presenting with chest pain were registered extensively. A follow-up form was filled in after 30 days. 22 294 patient contacts were registered. In 281 (1.26%), chest pain was a reason for consulting the GP (mean age for men 54.4/women 53 years). In this cohort of 281 patients, in 38.1% of patients, acute coronary syndrome (ACS) was suspected at least temporarily during consultation, 40.2% of patients were referred to secondary care and 512 diagnostic tests were performed by GPs and consulted specialists. Musculoskeletal pain was the most frequent working (26.1%) and final diagnoses (33.1%). Potentially life-threatening diseases as final diagnosis (such as myocardial infarction) accounted for 8.4% of all chest pain cases. In 23.1% of cases, a major difference between working and final diagnoses was found, in 0.7% a severe disease was initially missed by the GP. Chest pain was present in 281 patients (1.26% of all consultations). Final diagnoses were mostly non-life-threatening. Nevertheless, in 8.4% of patients with chest pain, life-threatening underlying causes were identified. This seems reflected in the magnitude and wide variety of diagnostic tests performed in these patients by GPs and specialists, in the (safe) overestimation of life-threatening diseases by GPs at initial assessment and in the high referral rate we found. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Strain distributions and their influence on electronic structures of WSe2-MoS2 laterally strained heterojunctions

Science.gov (United States)

Zhang, Chendong; Li, Ming-Yang; Tersoff, Jerry; Han, Yimo; Su, Yushan; Li, Lain-Jong; Muller, David A.; Shih, Chih-Kang

2018-02-01

Monolayer transition metal dichalcogenide heterojunctions, including vertical and lateral p-n junctions, have attracted considerable attention due to their potential applications in electronics and optoelectronics. Lattice-misfit strain in atomically abrupt lateral heterojunctions, such as WSe2-MoS2, offers a new band-engineering strategy for tailoring their electronic properties. However, this approach requires an understanding of the strain distribution and its effect on band alignment. Here, we study a WSe2-MoS2 lateral heterojunction using scanning tunnelling microscopy and image its moiré pattern to map the full two-dimensional strain tensor with high spatial resolution. Using scanning tunnelling spectroscopy, we measure both the strain and the band alignment of the WSe2-MoS2 lateral heterojunction. We find that the misfit strain induces type II to type I band alignment transformation. Scanning transmission electron microscopy reveals the dislocations at the interface that partially relieve the strain. Finally, we observe a distinctive electronic structure at the interface due to hetero-bonding.

Quality-control ranges for antimicrobial susceptibility testing by broth dilution of the Brachyspira hyodysenteriae type strain (ATCC 27164(T))

DEFF Research Database (Denmark)

Pringle, M.; Aarestrup, Frank Møller; Bergsjø, B.

2006-01-01

There are no approved standards for antimicrobial susceptibility testing of the fastidious spirochete Brachyspira hyodysenteriae. An interlaboratory study was performed to establish MIC quality control ranges for six antimicrobial agents for the type strain of B. hyodysenteriae using broth diluti....... The results showed that B. hyodysenteriae B78(T) ATCC 27164(T) is a suitable quality control strain. This is a first step toward standardization of methods regarding this anaerobe....

Dynamic Strength and Accumulated Plastic Strain Development Laws and Models of the Remolded Red Clay under Long-Term Cyclic Loads: Laboratory Test Results

Directory of Open Access Journals (Sweden)

Li Jian

2015-09-01

Full Text Available The dynamic strength and accumulated plastic strain are two important parameters for evaluating the dynamic response of soil. As a special clay, the remolded red clay is often used as the high speed railway subgrade filling, but studies on its dynamic characteristics are few. For a thorough analysis of the suitability of the remolded red clay as the subgrade filling, a series of long-term cyclic load triaxial test under different load histories are carried out. Considering the influence of compactness, confining pressure, consolidation ratio, vibration frequency and dynamic load to the remolded red clay dynamic property, the tests obtain the development curves of the dynamic strength and accumulated plastic strain under different test conditions. Then, through curve fitting method, two different hyperbolic models respectively for the dynamic strength and accumulated plastic strain are built, which can match the test datum well. By applying the dynamic strength model, the critical dynamic strength of the remolded red clay are gained. Meanwhile, for providing basic datum and reference for relevant projects, all key parameters for the dynamic strength and accumulated plastic strain of the remolded red clay are given in the paper.

The development of an enhanced strain measurement device to support testing of radioactive material packages

International Nuclear Information System (INIS)

Uncapkher, W.L.; Arviso, M.

1995-01-01

Radioactive material package designers use structural testing to verify and demonstrate package performance. A major part of evaluating structural response is the collection of reliable instrumentation measurement data. Over the last four decades, Sandia National Laboratories (SNL) has been actively involved in the development, testing, and evaluation of measurement devices for a broad range of applications, resulting in the commercialization of several measurement devices commonly used today. SNL maintains an ongoing program sponsored by the US Department of Energy (DOE) to develop and evaluate measurement devices to support testing of packages used to transport radioactive or hazardous materials. The development of the enhanced strain measurement device is part of this program

Influence of phosphorus on the tensile stress strain curves in copper

International Nuclear Information System (INIS)

Sandström, Rolf

2016-01-01

Copper canisters are planned to be used for final disposal of spent nuclear fuel in Sweden. The canisters will be exposed to slow plastic straining over extensive periods of time. To be able to predict the mechanical properties a range of basic models have previously been developed for copper with and without phosphorus (Cu-OFP, Cu-OF). Already with the small amount of phosphorus added in the canisters (60 wt. ppm) dramatic improvements in the measured creep strength and the creep ductility are found. The basic models are further developed in the present paper. The influence of phosphorus on slow strain rate tests is analysed. It is shown that the main effect of phosphorus is that it prevents brittle rupture, which is modelled by taking creep cavitation into account.

Influence of phosphorus on the tensile stress strain curves in copper

Energy Technology Data Exchange (ETDEWEB)

Sandström, Rolf, E-mail: rsand@kth.se

2016-03-15

Copper canisters are planned to be used for final disposal of spent nuclear fuel in Sweden. The canisters will be exposed to slow plastic straining over extensive periods of time. To be able to predict the mechanical properties a range of basic models have previously been developed for copper with and without phosphorus (Cu-OFP, Cu-OF). Already with the small amount of phosphorus added in the canisters (60 wt. ppm) dramatic improvements in the measured creep strength and the creep ductility are found. The basic models are further developed in the present paper. The influence of phosphorus on slow strain rate tests is analysed. It is shown that the main effect of phosphorus is that it prevents brittle rupture, which is modelled by taking creep cavitation into account.

Influence of phosphorus on the tensile stress strain curves in copper

Science.gov (United States)

Sandström, Rolf

2016-03-01

Copper canisters are planned to be used for final disposal of spent nuclear fuel in Sweden. The canisters will be exposed to slow plastic straining over extensive periods of time. To be able to predict the mechanical properties a range of basic models have previously been developed for copper with and without phosphorus (Cu-OFP, Cu-OF). Already with the small amount of phosphorus added in the canisters (60 wt. ppm) dramatic improvements in the measured creep strength and the creep ductility are found. The basic models are further developed in the present paper. The influence of phosphorus on slow strain rate tests is analysed. It is shown that the main effect of phosphorus is that it prevents brittle rupture, which is modelled by taking creep cavitation into account.

A study of graphite-epoxy laminate failures due to high transverse shear strains using the multi-span-beam shear test procedure

Science.gov (United States)

Jegley, Dawn C.

1989-01-01

The multi-span-beam shear test procedure is used to study failure mechanisms in graphite-epoxy laminates due to high transverse shear strains induced by severe local bending deformations in test specimens. Results of a series of tests on specimens with a variety of stacking sequences, including some with adhesive interleaving, are presented. These results indicate that laminates with stacking sequences with several + or - 45 and 90 deg plies next to each other are more susceptible to failures due to high transverse shear strains than laminates with + or - 45 and 0 deg plies next to each other or with + or - 45 deg plies next to layers of adhesive interleaving. Results of these tests are compared with analytical results based on finite elements.

Stress corrosion crack initiation of Zircaloy-4 cladding tubes in an iodine vapor environment during creep, relaxation, and constant strain rate tests

Science.gov (United States)

Jezequel, T.; Auzoux, Q.; Le Boulch, D.; Bono, M.; Andrieu, E.; Blanc, C.; Chabretou, V.; Mozzani, N.; Rautenberg, M.

2018-02-01

During accidental power transient conditions with Pellet Cladding Interaction (PCI), the synergistic effect of the stress and strain imposed on the cladding by thermal expansion of the fuel, and corrosion by iodine released as a fission product, may lead to cladding failure by Stress Corrosion Cracking (SCC). In this study, internal pressure tests were conducted on unirradiated cold-worked stress-relieved Zircaloy-4 cladding tubes in an iodine vapor environment. The goal was to investigate the influence of loading type (constant pressure tests, constant circumferential strain rate tests, or constant circumferential strain tests) and test temperature (320, 350, or 380 °C) on iodine-induced stress corrosion cracking (I-SCC). The experimental results obtained with different loading types were consistent with each other. The apparent threshold hoop stress for I-SCC was found to be independent of the test temperature. SEM micrographs of the tested samples showed many pits distributed over the inner surface, which tended to coalesce into large pits in which a microcrack could initiate. A model for the time-to-failure of a cladding tube was developed using finite element simulations of the viscoplastic mechanical behavior of the material and a modified Kachanov's damage growth model. The times-to-failure predicted by this model are consistent with the experimental data.

Autogenous shrinkage of Ducorit S5R ASTM C 1698-09 test method

DEFF Research Database (Denmark)

Damkilde, Lars

The report deals with experimental measurement of autogenous shrinkage of Ducorit S5R according to the test method ASTM C 1698-09. This test method measures the bulk strain of a sealed cementitious specimen, at constant temperature and not subjected to external forces, from the time of final...

Developmental Predictors of Violent Extremist Attitudes : A Test of General Strain Theory

NARCIS (Netherlands)

Nivette, Amy; Eisner, Manuel; Ribeaud, Denis

2017-01-01

Objectives: This study examines the influence of collective strain on support for violent extremism among an ethnically diverse sample of Swiss adolescents. This study explores two claims derived from general strain theory: (1) Exposure to collective strain is associated with higher support for

Probiotic Properties of Lactobacillus fermentum Strains Isolated from Human Oral Samples and Description of their Antibacterial Activity.

Science.gov (United States)

Fuochi, Virginia; Volti, Giovanni Li; Furneri, Pio M

2017-01-01

Gram positive bacteria produce peptides, defined bacteriocins which exhibit good antibacterial activity. We evaluated the ability of L. fermentum to produce bacteriocins having therefore, good probiotic features and finally, be safe towards microglial cells. Eight wild strains, identified using molecular techniques, were investigated for the evaluation of resistance to bile salts, low pH, H2O2 production, biofilm formation, antibacterial activity and safety on microglia cells (BV2). The determination of the susceptibility/resistance profile showed that the strains are sensitive to the antibiotics tested. All strains showed a good tolerability to extremely low pH as well as resisting in presence of bile salts. In addition, the strains showed excellent activity against pathogens and one of them (LAC 42) showed activity also against Pseudomonas aeruginosa and Klebsiella pneumoniae. Finally, LAC 42 and its active compound did not change microglia cell viability following 24h exposure. Our data on this antibacterial molecule suggest that it is a compound with low molecular weight and with highly hydrophilic component. These results describe the characteristics of Lactobacillus strains and provide evidences for their possible use as new potential probiotic. In addition, other studies are now warranted to exploit the antibacterial activity of the supernatant LAC 42 and for its complete chemical characterization. Copyright© Bentham Science Publishers; For any queries, please email at epub@benthamscience.org.

[Comparison of efficacy of tests for differentiation of typical and atypical strains of Yersinia pestis and Yersinia pseudotuberculosis].

Science.gov (United States)

Arsen'eva, T E; Lebedeva, S A; Trukhachev, A L; Vasil'eva, E A; Ivanova, V S; Bozhko, N V

2010-01-01

To characterize species specificity of officially recommended tests for differentiation of Yersiniapestis and Yersinia pseudotuberculosis and propose additional tests allowing for more accurate identification. Natural, laboratory and typical strains oftwo Yersinia species were studied using microbiological, molecular and biochemical methods. For PCR species-specific primers complementary to certain fragments of chromosomal DNA of each species as well as to several plasmid genes of Y. pestis were used. It was shown that such attributes of Y. pestis as form of colonies, fermentation ofrhamnose, melibiose and urea, susceptibility to diagnostic phages, nutritional requirements could be lost in pestis bacterial species or detected in pseudotuberculosis species. Such attribute as mobility as well as positive result of CoA-reaction on fraction V antigen are more reliable. Guaranteed differentiation of typical and changed according to differential tests strains is provided only by PCR-analysis with primers vlml2for/ISrev216 and JS respectively, which are homologous to certain chromosome fragments of one of two Yersinia species.

Weight and morphometric growth of different strains of tilapia (Oreochromis sp

Directory of Open Access Journals (Sweden)

Ivan Bezerra Allaman

2013-05-01

Full Text Available The objective of this study was to evaluate the morphometric growth and weight gain of strains of tilapia (Thai, Red, UFLA and Commercial by nonlinear models. Initially, 500 male fingerlings of each strain, at 85 (Red and UFLA and 86 (Thai and Commercial days of age, were stocked separately in raceways with 56 m³. Twenty fish of each strain were randomly sampled, weighed and measured monthly. Five nonlinear models (Brody, von Bertalanffy, Gompertz, logistic and exponential were tested, choosing one that best fit to the data. The variables studied were: weight, standard length (SL, head length (HL, height 1 (H1, height 2 (H2, height 3 (H3, first distance (D1, second distance (D2, first width (W1, second width (W2 and third width (W3. The exponential model had the best fit to weight and morphometric data, with the exception of W2, in which the best fitted model was von Bertalanffy. The convergence of the exponential model to data indicates that the cultivation period studied was not enough for the strains to reach maturity weight. The UFLA strain presented the lowest value for parameter "a" (initial weight estimate, 8.71 g, and the highest for parameter k (specific growth rate, 0.0127, when compared with other evaluated strains. However, the highest k of UFLA was not enough to overcome the final weight observed for the Commercial strain (603.1 g, which was higher than all other strains. Regarding the morphometric measurements, the UFLA strain also had the highest k for the variables SL, HL, HH, H1, H2, H3 and D2, and similar k to Commercial and Thai strains for the variables D1 and W3 respectively. The strains differ as to weight gain and morphometric growth.

A high temperature testing system for ceramic composites

Science.gov (United States)

Hemann, John

1994-01-01

Ceramic composites are presently being developed for high temperature use in heat engine and space power system applications. The operating temperature range is expected to be 1090 to 1650 C (2000 F to 3000 F). Very little material data is available at these temperatures and, therefore, it is desirable to thoroughly characterize the basic unidirectional fiber reinforced ceramic composite. This includes testing mainly for mechanical material properties at high temperatures. The proper conduct of such characterization tests requires the development of a tensile testing system includes unique gripping, heating, and strain measuring devices which require special considerations. The system also requires an optimized specimen shape. The purpose of this paper is to review various techniques for measuring displacements or strains, preferably at elevated temperatures. Due to current equipment limitations it is assumed that the specimen is to be tested at a temperature of 1430 C (2600F) in an oxidizing atmosphere. For the most part, previous high temperature material characterization tests, such as flexure and tensile tests, have been performed in inert atmospheres. Due to the harsh environment in which the ceramic specimen is to be tested, many conventional strain measuring techniques can not be applied. Initially a brief description of the more commonly used mechanical strain measuring techniques is given. Major advantages and disadvantages with their application to high temperature tensile testing of ceramic composites are discussed. Next, a general overview is given for various optical techniques. Advantages and disadvantages which are common to these techniques are noted. The optical methods for measuring strain or displacement are categorized into two sections. These include real-time techniques. Finally, an optical technique which offers optimum performance with the high temperature tensile testing of ceramic composites is recommended.

Variation in the strain anisotropy of Zircaloy with temperature and strain

International Nuclear Information System (INIS)

Hindle, E.D.; Worswick, D.

1984-04-01

Strain anisotropy was investigated at temperatures in the range 293 to 1117K in circular tensile specimens prepared from rolled Zircaloy-2 plate so that their tensile axes were parallel to and transverse to the rolling direction. The strain anisotropy factor for both types of specimen increased markedly in the high alpha phase region above 923K reaching a maximum at circa 1070K. Above this temperature in the alpha-plus-beta phase region the strain anisotropy decreased rapidly as the proportion of beta phase increased and was almost non-existent at 1173K. The strain anisotropy was markedly strain dependent, particularly in the high alpha phase region. The study was extended to Zircaloy-4 pressurized water reactor (PWR) 17 x 17 type fuel rod tubing specimens which were strained under biaxial conditions using cooling conditions which promoted uniform diametral strain over most of their lengths (circa 250 mm). In these circumstances the strain anisotropy is manifest by a reduction in length. Measurement of this change along with that in diameter and wall thickness produced data from which the strain anisotropy factor was calculated. The results, although influenced by additional factors discussed in the paper, were similar to those observed in the uniaxial Zircaloy-2 tensile tests. (author)

A behavioural test battery to investigate tic-like symptoms, stereotypies, attentional capabilities, and spontaneous locomotion in different mouse strains.

Science.gov (United States)

Proietti Onori, Martina; Ceci, Chiara; Laviola, Giovanni; Macrì, Simone

2014-07-01

The preclinical study of human disorders associated with comorbidities and for which the aetiology is still unclear may substantially benefit from multi-strain studies conducted in mice. The latter can help isolating experimental populations (strains) exhibiting distinct facets in the parameters isomorphic to the symptoms of a given disorder. Through a reverse-translation approach, multi-strain studies can inform both natural predisposing factors and environmental modulators. Thus, mouse strains selected for a particular trait may be leveraged to generate hypothesis-driven studies aimed at clarifying the potential role played by the environment in modulating the exhibition of the symptoms of interest. Tourette's syndrome (TS) constitutes a paradigmatic example whereby: it is characterized by a core symptom (tics) often associated with comorbidities (attention-deficit-hyperactivity and obsessive-compulsive symptoms); it has a clear genetic origin though specific genes are, as yet, unidentified; its course (exacerbations and remissions) is under the influence of environmental factors. Based on these considerations, we tested four mouse strains (ABH, C57, CD1, and SJL) - varying along a plethora of behavioural, neurochemical, and immunological parameters - on a test battery tailored to address the following domains: tics (through the i.p. administration of the selective 5-HT2 receptor agonist DOI, 5mg/kg); locomotion (spontaneous locomotion in the home-cage); perseverative responding in an attentional set shifting task; and behavioural stereotypies in response to a single amphetamine (10mg/kg, i.p.) injection. Present data demonstrate that while ABH and SJL mice respectively exhibit selective increments in amphetamine-induced sniffing behaviour and DOI-induced tic-like behaviours, C57 and CD1 mice show a distinct phenotype, compared to other strains, in several parameters. Copyright © 2014 Elsevier B.V. All rights reserved.

Fuel-pin cladding transient failure strain criterion

International Nuclear Information System (INIS)

Bard, F.E.; Duncan, D.R.; Hunter, C.W.

1983-01-01

A criterion for cladding failure based on accumulated strain was developed for mixed uranium-plutonium oxide fuel pins and used to interpret the calculated strain results from failed transient fuel pin experiments conducted in the Transient Reactor Test (TREAT) facility. The new STRAIN criterion replaced a stress-based criterion that depends on the DORN parameter and that incorrectly predicted fuel pin failure for transient tested fuel pins. This paper describes the STRAIN criterion and compares its prediction with those of the stress-based criterion

VAMAS Nb3Sn test conductor

International Nuclear Information System (INIS)

Anon.

1994-01-01

A bronze-process Nb 3 Sn conductor was measured as part of the second VAMAS (Versailles Project on Advanced Materials and Standards) international critical-current round robin. The conductor specifications are given in Table 15. The critical current was measured as a function of magnetic field and axial tensile strain. The measured data are presented in Table 16 and in Figs. 23 and 24. The I c and J c values are based on an electric field criterion (E c ) of 1 μV/cm. In the first VAMAS round robin tests, differences in the test specimens' axial strain, caused by variations in the thermal contraction of different test fixtures, was a major source of interlaboratory variation in the critical-current data. Consequently, electromechanical characterization of the test specimen is important for data interpretation and error analysis. In the second round robin, the test apparatus and procedure were more rigidly specified. This increased experimental control reduced the critical-current variation by a factor of 3.5. The results of our measurements will be published in the final VAMAS report

An Approach for the Dynamic Measurement of Ring Gear Strains of Planetary Gearboxes Using Fiber Bragg Gratings

Directory of Open Access Journals (Sweden)

Hang Niu

2017-12-01

Full Text Available The strain of the ring gear can reflect the dynamic characteristics of planetary gearboxes directly, which makes it an ideal signal to monitor the health condition of the gearbox. To overcome the disadvantages of traditional methods, a new approach for the dynamic measurement of ring gear strains using fiber Bragg gratings (FBGs is proposed in this paper. Firstly, the installation of FBGs is determined according to the analysis for the strain distribution of the ring gear. Secondly, the parameters of the FBG are determined in consideration of the accuracy and sensitivity of the measurement as well as the size of the ring gear. The strain measured by the FBG is then simulated under non-uniform strain field conditions. Thirdly, a dynamic measurement system is built and tested. Finally, the strains of the ring gear are measured in a planetary gearbox under normal and faulty conditions. The experimental results showed good agreement with the theoretical results in values, trends, and the fault features can be seen from the time domain of the measured strain signal, which proves that the proposed method is feasible for the measurement of the ring gear strains of planetary gearboxes.

An Approach for the Dynamic Measurement of Ring Gear Strains of Planetary Gearboxes Using Fiber Bragg Gratings.

Science.gov (United States)

Niu, Hang; Zhang, Xiaodong; Hou, Chenggang

2017-12-16

The strain of the ring gear can reflect the dynamic characteristics of planetary gearboxes directly, which makes it an ideal signal to monitor the health condition of the gearbox. To overcome the disadvantages of traditional methods, a new approach for the dynamic measurement of ring gear strains using fiber Bragg gratings (FBGs) is proposed in this paper. Firstly, the installation of FBGs is determined according to the analysis for the strain distribution of the ring gear. Secondly, the parameters of the FBG are determined in consideration of the accuracy and sensitivity of the measurement as well as the size of the ring gear. The strain measured by the FBG is then simulated under non-uniform strain field conditions. Thirdly, a dynamic measurement system is built and tested. Finally, the strains of the ring gear are measured in a planetary gearbox under normal and faulty conditions. The experimental results showed good agreement with the theoretical results in values, trends, and the fault features can be seen from the time domain of the measured strain signal, which proves that the proposed method is feasible for the measurement of the ring gear strains of planetary gearboxes.

Towards Scalable Strain Gauge-Based Joint Torque Sensors

Science.gov (United States)

D’Imperio, Mariapaola; Cannella, Ferdinando; Caldwell, Darwin G.; Cuschieri, Alfred

2017-01-01

During recent decades, strain gauge-based joint torque sensors have been commonly used to provide high-fidelity torque measurements in robotics. Although measurement of joint torque/force is often required in engineering research and development, the gluing and wiring of strain gauges used as torque sensors pose difficulties during integration within the restricted space available in small joints. The problem is compounded by the need for a scalable geometric design to measure joint torque. In this communication, we describe a novel design of a strain gauge-based mono-axial torque sensor referred to as square-cut torque sensor (SCTS), the significant features of which are high degree of linearity, symmetry, and high scalability in terms of both size and measuring range. Most importantly, SCTS provides easy access for gluing and wiring of the strain gauges on sensor surface despite the limited available space. We demonstrated that the SCTS was better in terms of symmetry (clockwise and counterclockwise rotation) and more linear. These capabilities have been shown through finite element modeling (ANSYS) confirmed by observed data obtained by load testing experiments. The high performance of SCTS was confirmed by studies involving changes in size, material and/or wings width and thickness. Finally, we demonstrated that the SCTS can be successfully implementation inside the hip joints of miniaturized hydraulically actuated quadruped robot-MiniHyQ. This communication is based on work presented at the 18th International Conference on Climbing and Walking Robots (CLAWAR). PMID:28820446

Studies on Stress-Strain Relationships of Polymeric Materials Used in Space Applications

Science.gov (United States)

Jana, Sadhan C.; Freed, Alan

2002-01-01

A two-year research plan was undertaken in association with Polymers Branch, NASA Glenn Research Center, to carry out experimental and modeling work relating stress and strain behavior of polymeric materials, especially elastomers and vulcanized rubber. An experimental system based on MTS (Mechanical Testing and Simulation) A/T-4 test facility environment has been developed for a broader range of polymeric materials in addition to a design of laser compatible temperature control chamber for online measurements of various strains. Necessary material processing has been accomplished including rubber compounding and thermoplastic elastomer processing via injection molding. A broad suite of testing methodologies has been identified to reveal the complex non-linear mechanical behaviors of rubbery materials when subjected to complex modes of deformation. This suite of tests required the conceptualization, design and development of new specimen geometries, test fixtures, and test systems including development of a new laser based technique to measure large multi-axial deformations. Test data has been generated for some of these new fixtures and has revealed some complex coupling effects generated during multi-axial deformations. In addition, fundamental research has been conducted concerning the foundation principles of rubber thermodynamics and resulting theories of rubber elasticity. Studies have been completed on morphological properties of several thermoplastic elastomers. Finally, a series of steps have been identified to further advance the goals of NASA's ongoing effort.

Development of new testing methods for the numerical load analysis for the drop test of steel sheet containers for the final repository Konrad

International Nuclear Information System (INIS)

Protz, C.; Voelzke, H.; Zencker, U.; Hagenow, P.; Gruenewald, H.

2011-01-01

The qualification of steel sheet containers as intermediate-level waste container for the final repository is performed by the BAM (Bundeasmt fuer Materialpruefung) according to the BfS (Bundesamt fuer Strahlenschutz) requirements. The testing requirements include the stacking pressure tests, lifting tests, drop tests thermal tests (fire resistance) and tightness tests. Besides the verification using model or prototype tests and transferability considerations numerical safety analyses may be performed alternatively. The authors describe the internal BAM research project ConDrop aimed to develop extended testing methods for the drop test of steel sheet containers for the final repository Konrad using numerical load analyses. A finite element model was developed using The FE software LS-PrePost 3.0 and ANSYS 12.0 and the software FE-Code LS-DYNA for the simulation of the drop test (5 m height). The results were verified by experimental data from instrumented drop tests. The container preserves its integrity after the drop test, plastic deformation occurred at the bottom plate, the side walls, the cask cover and the lateral uprights.

Context and strain-dependent behavioral response to stress

Directory of Open Access Journals (Sweden)

Baum Amber E

2008-06-01

Full Text Available Abstract Background This study posed the question whether strain differences in stress-reactivity lead to differential behavioral responses in two different tests of anxiety. Strain differences in anxiety-measures are known, but strain differences in the behavioral responses to acute prior stress are not well characterized. Methods We studied male Fisher 344 (F344 and Wistar Kyoto (WKY rats basally and immediately after one hour restraint stress. To distinguish between the effects of novelty and prior stress, we also investigated behavior after repeated exposure to the test chamber. Two behavioral tests were explored; the elevated plus maze (EPM and the open field (OFT, both of which are thought to measure activity, exploration and anxiety-like behaviors. Additionally, rearing, a voluntary behavior, and grooming, a relatively automatic, stress-responsive stereotyped behavior were measured in both tests. Results Prior exposure to the test environment increased anxiety-related measures regardless of prior stress, reflecting context-dependent learning process in both tests and strains. Activity decreased in response to repeated testing in both tests and both strains, but prior stress decreased activity only in the OFT which was reversed by repeated testing. Prior stress decreased anxiety-related measures in the EPM, only in F344s, while in the OFT, stress led to increased freezing mainly in WKYs. Conclusion Data suggest that differences in stressfulness of these tests predict the behavior of the two strains of animals according to their stress-reactivity and coping style, but that repeated testing can overcome some of these differences.

Comparison of Disk Diffusion and E-Test Methods for Doripenem Susceptibility of Nosocomial Acinetobacter Baumannii Strains

Directory of Open Access Journals (Sweden)

Yesim Cekin

2014-03-01

Full Text Available Aim: Acinetobacter species are amoung the most common two cause of infections isolated from patients of intensive care unit in our hospital. Doripenem which acts by inhibiting cell wall synthesis is resently introduced for use in our country is broad spectrum antibiotic belonging to carbapenems. There are many studies investigating the susceptibility of doripenem of Acinetobacter baumannii which is isolated as a cause of ventilatory associated pneumonia in the literature. We aimed to compare e-test and disc diffusion methods for doripenem susceptibility of acinetobacter baumannii strains as nosocomial infections Acinetobacter baumanni isolates detected as nosocomial infection. Material and Method:. Between January to December, 2009 a total of 94 Acinetobacter baumanni strains isolated from different clinical specimens from intensive care units have been studied for doripenem susceptibility by disc diffusion and E-test methods. Minimal inhibitory consantrations (MIC were accepted as; sensitive %u22641 %u03BCg/ml, intermadiate 2-4 %u03BCg/ml, resistant >4 %u03BCg/ml and diameters of inhibition zone with 10 µg disc; sensitive

Properties of strain gages at cryogenic temperature

International Nuclear Information System (INIS)

Shibata, Nobuo; Fujiyoshi, Toshimitsu.

1978-01-01

At the time of developing superconduction generators, the stress measurement for rotor parts is required to grasp the safety and performance of the rotor at cryogenic temperature, which is cooled with liquid helium. In case of carrying out the stress measurement with strain gages, the problems are as follows. The strain gages and lead wires are exposed to cryogenic temperature from 4 to 10 K and strong magnetic field of about 3T, and subjected to high centrifugal acceleration of about 500G. In order to establish the techniques of the stress measurement under such conditions, the adhesives and damp-proof coatings for strain gages and strain gages themselves in Japan and foreign countries were examined on the properties at cryogenic temperature. As for the properties of strain gages, mainly the apparent strain owing to temperature change was investigated, and the change of the gage factors was studies only at liquid nitrogen temperature. The stress measurement with strain gages at low temperature had been studied in detail down to liquid nitrogen temperature concerning LNG tanks. The experimental apparatus, the samples, the testing methods and the test results of cooling tests on adhesives and damp-proof coatings, and the temperature characteristics of strain gages are reported. The usable adhesives and coatings were found, and correction by accurate temperature measurement is required for apparent strain. (Kako, I.)

Thermal strain measurement of EAST W/Cu divertor structure using electric resistance strain gauges

Energy Technology Data Exchange (ETDEWEB)

Wang, Xingli [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Science Island Branch of Graduate School, University of Science & Technology of China, Hefei, 230031 (China); Wang, Wanjing, E-mail: wjwang@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Wang, Jichao [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Wei, Ran; Sun, Zhaoxuan [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Science Island Branch of Graduate School, University of Science & Technology of China, Hefei, 230031 (China); Li, Qiang; Xie, Chunyi [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Chen, Hong-En; Wang, Kaiqiang; Wu, Lei; Chen, Zhenmao [State Key Lab for Strength and Vibration of Mechanical Structures, Xi’an Jiaotong University (China); Luo, Guang-Nan [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, 230031 (China); Science Island Branch of Graduate School, University of Science & Technology of China, Hefei, 230031 (China); Hefei Center for Physical Science and Technology, Hefei, 230022 (China); Hefei Science Center of Chinese Academy of Sciences, Hefei, 230027 (China)

2016-12-15

Highlights: • To understand the service behavior of W/Cu divertor, an electrical resistance strain gauge system had been introduced in a thermal strain measurement experiment. • The measurement system successfully finished the experiment and obtained valued thermal strain data. • Two thermomechanical analyses had also been carried out and compared with the measurement results. • Experiment results corresponded well to simulations and threw a light upon the failure of W/Cu divertor in the previous baking tests. - Abstract: W/Cu divertor has complex structure and faces extreme work environment in EAST Tokamak device. To measure its thermal strain shall be a valued way to understand its service behavior and then optimize its design and manufacturing process. This work presents a preliminary study on measuring thermal strain of EAST W/Cu divertor structure using electric resistance strain gauges. Eight gauges had been used in the experiment and the heating temperature had been set to 230 °C with respect to the work temperature. To realize the measuring experiment, an appropriate fixing method of gauges in divertor narrow spaces had been taken and tested, which could not only withstand high temperature but also had no damage to the divertor sample. The measurement results were that three gauges showed positive strain while other three showed negative strain after having been compensated, which corresponded to tensile stress and compressed stress respectively. Two thermomechanical simulations had also been carried out and used for comparing with the experiment.

Numerical development of a new correlation between biaxial fracture strain and material fracture toughness for small punch test

Energy Technology Data Exchange (ETDEWEB)

Kumar, Pradeep [Homi Bhabha National Institute, Anushaktinagar, Mumbai 400094 (India); Dutta, B.K., E-mail: bijon.dutta@gmail.com [Homi Bhabha National Institute, Anushaktinagar, Mumbai 400094 (India); Chattopadhyay, J. [Homi Bhabha National Institute, Anushaktinagar, Mumbai 400094 (India); Reactor Safety Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

2017-04-01

The miniaturized specimens are used to determine mechanical properties of the materials, such as yield stress, ultimate stress, fracture toughness etc. Use of such specimens is essential whenever limited quantity of material is available for testing, such as aged/irradiated materials. The miniaturized small punch test (SPT) is a technique which is widely used to determine change in mechanical properties of the materials. Various empirical correlations are proposed in the literature to determine the value of fracture toughness (J{sub IC}) using this technique. bi-axial fracture strain is determined using SPT tests. This parameter is then used to determine J{sub IC} using available empirical correlations. The correlations between J{sub IC} and biaxial fracture strain quoted in the literature are based on experimental data acquired for large number of materials. There are number of such correlations available in the literature, which are generally not in agreement with each other. In the present work, an attempt has been made to determine the correlation between biaxial fracture strain (ε{sub qf}) and crack initiation toughness (J{sub i}) numerically. About one hundred materials are digitally generated by varying yield stress, ultimate stress, hardening coefficient and Gurson parameters. Such set of each material is then used to analyze a SPT specimen and a standard TPB specimen. Analysis of SPT specimen generated biaxial fracture strain (ε{sub qf}) and analysis of TPB specimen generated value of J{sub i}. A graph is then plotted between these two parameters for all the digitally generated materials. The best fit straight line determines the correlation. It has been also observed that it is possible to have variation in J{sub i} for the same value of biaxial fracture strain (ε{sub qf}) within a limit. Such variation in the value of J{sub i} has been also ascertained using the graph. Experimental SPT data acquired earlier for three materials were then used to get J

Effect of Temperature on the Prevalence of Saccharomyces Non cerevisiae Species against a S. cerevisiae Wine Strain in Wine Fermentation: Competition, Physiological Fitness, and Influence in Final Wine Composition

Science.gov (United States)

Alonso-del-Real, Javier; Lairón-Peris, María; Barrio, Eladio; Querol, Amparo

2017-01-01

Saccharomyces cerevisiae is the main microorganism responsible for the fermentation of wine. Nevertheless, in the last years wineries are facing new challenges due to current market demands and climate change effects on the wine quality. New yeast starters formed by non-conventional Saccharomyces species (such as S. uvarum or S. kudriavzevii) or their hybrids (S. cerevisiae x S. uvarum and S. cerevisiae x S. kudriavzevii) can contribute to solve some of these challenges. They exhibit good fermentative capabilities at low temperatures, producing wines with lower alcohol and higher glycerol amounts. However, S. cerevisiae can competitively displace other yeast species from wine fermentations, therefore the use of these new starters requires an analysis of their behavior during competition with S. cerevisiae during wine fermentation. In the present study we analyzed the survival capacity of non-cerevisiae strains in competition with S. cerevisiae during fermentation of synthetic wine must at different temperatures. First, we developed a new method, based on QPCR, to quantify the proportion of different Saccharomyces yeasts in mixed cultures. This method was used to assess the effect of competition on the growth fitness. In addition, fermentation kinetics parameters and final wine compositions were also analyzed. We observed that some cryotolerant Saccharomyces yeasts, particularly S. uvarum, seriously compromised S. cerevisiae fitness during competences at lower temperatures, which explains why S. uvarum can replace S. cerevisiae during wine fermentations in European regions with oceanic and continental climates. From an enological point of view, mixed co-cultures between S. cerevisiae and S. paradoxus or S. eubayanus, deteriorated fermentation parameters and the final product composition compared to single S. cerevisiae inoculation. However, in co-inoculated synthetic must in which S. kudriavzevii or S. uvarum coexisted with S. cerevisiae, there were fermentation

Apt strain measurement technique for impulsive loading applications

International Nuclear Information System (INIS)

Nanda, Soumya Ranjan; Kulkarni, Vinayak; Sahoo, Niranjan

2017-01-01

The necessity of precise measurement of strain time history for impulsive loading applications has been addressed in the present investigation. Finite element modeling is initially carried out for a hemispherical test model and stress bar assembly to arrive at an appropriate location for strain measurement. In dynamic calibration experiments, strain measurements are performed using two wire and three wire quarter bride arrangements along with half bridge circuit. Usefulness of these arrangements has been verified by analyzing strain signals in time and frequency domains. Comparison of recovered force time histories proved that the half bridge circuit is the most suitable for such applications. Actual shock tube testing of the instrumented hemispherical test model confirmed the applicability of half bridge circuit for short duration strain measurements. (technical note)

Indirect deformation (strain) measurements and calibrations in Sandia triaxial apparatus for rock testing to 2500C

International Nuclear Information System (INIS)

Wawersik, W.R.

1979-09-01

Indirect procedures for axial and radial strain measurements on rock in triaxial tests to 250 0 C are presented. The description of techniques includes discussions of all calibrations and of the accuracies of measurements. In addition, two examples are given to show how the techniques are implemented in triaxial compression and triaxial extension experiments. 10 figures

[Characteristics of Lactobacillus strains contained in pharmaceuticals].

Science.gov (United States)

Banach, W; Bucholc, B; Wójcik, B

2001-01-01

The aim of the study was to characterize lactic acid bacteria (LAB) which are components of drugs administered orally in cases of intestinal disturbances, or antibiotic--related diarrhea. Biochemical properties, growth behavior, bile tolerance, and survival at low pH of six LAB strains (four strains L. rhamnosus and two L. acidophilus) were studied. The survival at low pH was determined in MRS broth (Difco) acidified to pH 1; 2; 3; and 4. Bile tolerance was tested on MRS broth with 0.3% oxgall (Difco). Between tested strains differences in ability to grow at low pH and survival in bile were observed. Only 0.01% inoculum of all examined strains survived at pH 1. Differences between strains in survival at low pH (pH 2 and pH 3) and tolerance of bile were observed. However, after 2 h incubation at pH 4, 100% of strains stayed alive. Examined strains demonstrated good 3% bile tolerance. All strains met the criteria for probiotic strains: ability to survive at pH 3 and in the presence of bile.

Computer-aided dispatch--traffic management center field operational test : Washington State final report

Science.gov (United States)

2006-05-01

This document provides the final report for the evaluation of the USDOT-sponsored Computer-Aided Dispatch - Traffic Management Center Integration Field Operations Test in the State of Washington. The document discusses evaluation findings in the foll...

CERTS Microgrid Laboratory Test Bed - PIER Final Project Report

Energy Technology Data Exchange (ETDEWEB)

Eto, Joseph H.; Eto, Joseph H.; Lasseter, Robert; Schenkman, Ben; Klapp, Dave; Linton, Ed; Hurtado, Hector; Roy, Jean; Lewis, Nancy Jo; Stevens, John; Volkommer, Harry

2008-07-25

The objective of the CERTS Microgrid Laboratory Test Bed project was to enhance the ease of integrating small energy sources into a microgrid. The project accomplished this objective by developing and demonstrating three advanced techniques, collectively referred to as the CERTS Microgrid concept, that significantly reduce the level of custom field engineering needed to operate microgrids consisting of small generating sources. The techniques comprising the CERTS Microgrid concept are: 1) a method for effecting automatic and seamless transitions between grid-connected and islanded modes of operation; 2) an approach to electrical protection within the microgrid that does not depend on high fault currents; and 3) a method for microgrid control that achieves voltage and frequency stability under islanded conditions without requiring high-speed communications. The techniques were demonstrated at a full-scale test bed built near Columbus, Ohio and operated by American Electric Power. The testing fully confirmed earlier research that had been conducted initially through analytical simulations, then through laboratory emulations, and finally through factory acceptance testing of individual microgrid components. The islanding and resychronization method met all Institute of Electrical and Electronics Engineers 1547 and power quality requirements. The electrical protections system was able to distinguish between normal and faulted operation. The controls were found to be robust and under all conditions, including difficult motor starts. The results from these test are expected to lead to additional testing of enhancements to the basic techniques at the test bed to improve the business case for microgrid technologies, as well to field demonstrations involving microgrids that involve one or mroe of the CERTS Microgrid concepts.

Final Test at the Surface of the ATLAS Endcap Muon Trigger Chamber Electronics

CERN Document Server

Kubota, T; Kanaya, N; Kawamoto, T; Kobayashi, T; Kuwabara, T; Nomoto, H; Sakamoto, H; Yamaguchi, T; Fukunaga, C; Ikeno, M; Iwasaki, H; Nagano, K; Nozaki, M; Sasaki, O; Tanaka, S; Yasu, Y; Hasegawa, Y; Oshita, H; Takeshita, T; Nomachi, M; Sugaya, Y; Sugimoto, T; Okumura, Y; Takahashi, Y; Tomoto, M; Kadosaka, T; Kawagoe, K; Kiyamura, H; Kurashige, H; Niwa, T; Ochi, A; Omachi, C; Takeda, H; Lifshitz, R; Lupu, N; Bressler, S; Tarem, S; Kajomovitz, E; Ben Ami, S; Bahat Treidel, O; Benhammou, Ya; Etzion, E; Lellouch, D; Levinson, L; Mikenberg, G; Roich, A

2007-01-01

For the detector commissioning planned in 2007, sector assembly of the ATLAS muon-endcap trigger chambers and final test at the surface for the assembled electronics are being done in CERN and almost completed. For the test, we built up the Data Acquisition (DAQ) system using test pulse of two types and cosmic rays in order to check functionality of the various aspects of the electronics mounted on a sector. So far, 99% of all 320,000 channels have been tested and most of them were installed into the ATLAS cavern. In this presentation, we will describe the DAQ systems and mass-test procedure in detail, and report the result of electronics test with some actual experiences

Full-Length High-Temperature Severe Fuel Damage Test No. 5: Final safety analysis

International Nuclear Information System (INIS)

Lanning, D.D.; Lombardo, N.J.; Panisko, F.E.

1993-09-01

This report presents the final safety analysis for the preparation, conduct, and post-test discharge operation for the Full-Length High Temperature Experiment-5 (FLHT-5) to be conducted in the L-24 position of the National Research Universal (NRU) Reactor at Chalk River Nuclear Laboratories (CRNL), Ontario, Canada. The test is sponsored by an international group organized by the US Nuclear Regulatory Commission. The test is designed and conducted by staff from Pacific Northwest Laboratory with CRNL staff support. The test will study the consequences of loss-of-coolant and the progression of severe fuel damage

Development of a Brillouin scattering based distributed fibre optic strain sensor

Science.gov (United States)

Brown, Anthony Wayne

2001-07-01

The parameters of the Brillouin spectrum of an optical fibre depend upon the strain and temperature conditions of the fibre. As a result, fibre optic distributed sensors based on Brillouin scattering can measure strain and temperature in arbitrary regions of a sensing fibre. In the past, such sensors have often been demonstrated under laboratory conditions, demonstrating the principle of operation. Although some field tests of temperature sensing have been reported, the actual deployment of such sensors in the field for strain measurements has been limited by poor spatial resolution (typically 1 m or more) and poor strain accuracy (+/-100 muepsilon). Also, cross-sensitivity of the Brillouin spectrum to temperature further reduces the accuracy of strain measurement while long acquisition times hinders field use. The high level of user knowledge and lack of automation required to operate the equipment is another limiting factor of the only commercially available unit. The potential benefits of distributed measurements are great for instrumentation of civil structures provided that the above limitations are overcome. However, before this system is used with confidence by practitioners, it is essential that it can be effectively operated in field conditions. In light of this, the fibre optics group at the University of New Brunswick has been developing an automated system for field measurement of strain in civil structures, particularly in reinforced concrete. The development of the sensing system hardware and software was the main focus of this thesis. This has been made possible, in part, by observation of the Brillouin spectrum for the case of using very short light pulses (performance to measure strain to an accuracy of 10 muepsilon; and allow the simultaneous measurement of strain and temperature to an accuracy of 204 muepsilon and 3°C are presented. Finally, the results of field measurement of strain on a concrete structure are presented.

Bisphenol A; Final Test Rule

Science.gov (United States)

EPA is issuing a final rule, under section 4 of the Toxic Substances Control Act (TSCA) requiring manufacturers and processors of bisphenol A, hereinafter BPA, (4.4’-isopropylidenediphenol, CAS No. 80-05—7) to conduct a 90-day inhalation study.

Macro and intergranular stress responses of austenitic stainless steel to 90° strain path changes

International Nuclear Information System (INIS)

Gonzalez, D.; Kelleher, J.F.; Quinta da Fonseca, J.; Withers, P.J.

2012-01-01

Highlights: ► We measure and model the macro and IG stresses of ASS to 90° strain path changes. ► The macro stress–strain curves show a clear Bauschinger effect on reloading. ► This is only partially captured by the model. ► The measured {h k l} families show an earlier microyield than predicted. ► This difference is more noticeable for a strain path with a higher reversibility. - Abstract: Strain path history can play a crucial role in sensitising/desensitising metals to various damage mechanisms and yet little work has been done to quantify and understand how intergranular strains change upon path changes, or their effect on the macroscopic behaviour. Here we have measured, by neutron diffraction, and modelled, by crystal plasticity finite elements, the stress–strain responses of 316L stainless steel over three different 90° strain path changes using an assembled microstructure of randomly oriented crystallites. The measurements show a clear Bauschinger effect on reloading that is only partially captured by the model. Further, measurements of the elastic response of different {h k l} grain families revealed an even earlier onset of yield for strain paths reloaded in compression while a strain path reloaded in tension showed good agreement with corresponding predictions. Finally, we propose that the study of strain path effects provides a more rigorous test of crystal plasticity models than conventional in situ diffraction studies of uniaxial loading.

High Strain Rate Characterisation of Composite Materials

DEFF Research Database (Denmark)

Eriksen, Rasmus Normann Wilken

-reinforced polymers, were considered, and it was first shown that the loading history controls equilibrium process. Then the High-speed servo-hydraulic test machine was analysed in terms its ability to create a state of constant strain rate in the specimen. The invertible inertial forces in the load train prevented...... from designing and constructing a high-speed servo-hydraulic test machine and by performing a comprehensive test series. The difficulties encountered in the test work could be addressed with the developed analysis. The conclusion was that the High-speed servo-hydraulic test machine is less suited...... for testing fibre-reinforced polymers due to their elastic behaviour and low strain to failure. This is problematic as the High-speed servo-hydraulic test machine closes the gap between quasi-static tests rates and lower strain rates, which are achievable with the Split Hopkinson Pressure Bar. The Split...

Survey of strain distribution and antibiotic resistance pattern of group B streptococci (Streptococcus agalactiae isolated from clinical specimens

Directory of Open Access Journals (Sweden)

Mousavi, Seyed Masoud

2016-09-01

Full Text Available Aim: The aims of the present study were to determine the antibiotic susceptibility profils with particular emphasis on susceptible or resistant strains to macrolides and lincosamids antibiotics and to determine possible antibiotic resistance mechanisms occurring in group B streptococci (GBS strains using PCR assay and disk diffusion method.Methods: A total of 62 clinical GBS strains were investigated. Antibacterial susceptibility testing was performed using the disk diffusion method and inducible resistance test for clindamycin by standard double disk diffusion or D-zone test for all isolates to differentiate macrolide resistance phenotype (M, constitutive macrolide-lincosamide-streptogramin B phenotype (cMLS and induced macrolide-lincosamide-streptogramin B phenotype (iMLS. In addition, minimum inhibitory concentrations (MIC of penicillin were determined for all isolates. Finally, possible existence of antibiotic resistance genes for erythromycin , and and for clindamycin were examined among isolates using PCR assay.Results: All 62 isolates were susceptible to penicillin, ampicillin, linezolid, cefazoline and vancomycin. However, 93.5% (n=58 of isolates showed an increased MIC to penicillin. The overall rate of erythromycin resistance was 35.5% (n=22. All erythromycin-resistant isolates displayed the M phenotype (100%, n=22. All three erythromycin resistance genes (i.e. , and were found in erythromycin-resistant isolates.Conclusion: It was concluded that prescribing antibiotic without antibacterial susceptibility tests should be prevented because of the high prevalence of erythromycin-resistant GBS strains and the fact that erythromycin-resistant GBS strains has shown an increased MIC to penicillin, as the drug of choice for treating GBS infections.

Strain distributions and their influence on electronic structures of WSe2–MoS2 laterally strained heterojunctions

KAUST Repository

Zhang, Chendong

2018-01-12

Monolayer transition metal dichalcogenide heterojunctions, including vertical and lateral p–n junctions, have attracted considerable attention due to their potential applications in electronics and optoelectronics. Lattice-misfit strain in atomically abrupt lateral heterojunctions, such as WSe2–MoS2, offers a new band-engineering strategy for tailoring their electronic properties. However, this approach requires an understanding of the strain distribution and its effect on band alignment. Here, we study a WSe2–MoS2 lateral heterojunction using scanning tunnelling microscopy and image its moiré pattern to map the full two-dimensional strain tensor with high spatial resolution. Using scanning tunnelling spectroscopy, we measure both the strain and the band alignment of the WSe2–MoS2 lateral heterojunction. We find that the misfit strain induces type II to type I band alignment transformation. Scanning transmission electron microscopy reveals the dislocations at the interface that partially relieve the strain. Finally, we observe a distinctive electronic structure at the interface due to hetero-bonding.

Strain distributions and their influence on electronic structures of WSe2–MoS2 laterally strained heterojunctions

KAUST Repository

Zhang, Chendong; Li, Ming-yang; Tersoff, Jerry; Han, Yimo; Su, Yushan; Li, Lain-Jong; Muller, David A.; Shih, Chih-Kang

2018-01-01

Monolayer transition metal dichalcogenide heterojunctions, including vertical and lateral p–n junctions, have attracted considerable attention due to their potential applications in electronics and optoelectronics. Lattice-misfit strain in atomically abrupt lateral heterojunctions, such as WSe2–MoS2, offers a new band-engineering strategy for tailoring their electronic properties. However, this approach requires an understanding of the strain distribution and its effect on band alignment. Here, we study a WSe2–MoS2 lateral heterojunction using scanning tunnelling microscopy and image its moiré pattern to map the full two-dimensional strain tensor with high spatial resolution. Using scanning tunnelling spectroscopy, we measure both the strain and the band alignment of the WSe2–MoS2 lateral heterojunction. We find that the misfit strain induces type II to type I band alignment transformation. Scanning transmission electron microscopy reveals the dislocations at the interface that partially relieve the strain. Finally, we observe a distinctive electronic structure at the interface due to hetero-bonding.

The effect of strain-rate on the tensile and compressive behavior of graphene reinforced epoxy/nanocomposites

International Nuclear Information System (INIS)

Shadlou, Shahin; Ahmadi-Moghadam, Babak; Taheri, Farid

2014-01-01

Highlights: • The epoxy/graphene nanocomposites were studied at various strain rates. • The variations in constitutive stress–strain response were scrutinized. • Positive reinforcing attributes of graphene diminished at higher strain rates. • Graphene particles have higher efficiency under compression loading than tension. • A new modification factor for Halpin–Tsai model was proposed. - Abstract: The effect of strain rate on the mechanical behavior of epoxy reinforced with graphene nanoplatelets (GNPs) is investigated. Nanocomposites containing various amounts of GNP are prepared and tested at four different strain rates (0.01, 0.1, 1 and 10/s) under compressive and tensile loading regimes. The results show that incorporation of GNP highly affects the behavior of epoxy. The fracture surfaces of tensile specimens are also investigated using scanning electron microscopy (SEM) to discern the surface features and dispersion state of GNP. Finally, the predictive capability of some of the available models for evaluating the strength of nanocomposites are assessed and compared against the experimental results. Moreover, a modification factor to the widely used Halpin–Tsai model is proposed to improve the accuracy of the model when evaluating the Young’s modulus of nanocomposites at various strain rates

Residual strain, scale effects, and time-dependent behaviour at the 240-m level of the underground research laboratory

International Nuclear Information System (INIS)

Read, R.S.

1990-01-01

Two subhorizontal, orthogonal boreholes were monitored continuously during concentric overcoring at the 240-m level of the Underground Research Laboratory (URL). The magnitude and orientation of principal residual strain components in the near-field stress regime were determined assuming linear elastic behaviour of the rock mass and isotropic conditions. In terms of magnitude, results compared favourably with those from previous tests at the 240-m level. However, orientation results were inconclusive. The effects of scale and borehole orientation relative to the principal stress direction on the results from a modified CSIR triaxial cell overcore test were also investigated; no scale effects were apparent in the experiment, but borehole orientation did affect results. Finally, time-dependent behaviour was detected in the Lac du Bonnet granite, and was monitored between successive overcore tests in one of the boreholes. Results on residual strain, scale effects, and time-dependent behaviour are presented, along with limitations and possible modifications to the testing procedure

A Dynamic Alignment System for the Final Focus Test Beam

International Nuclear Information System (INIS)

Ruland, R.E.; Bressler, V.E.; Fischer, G.; Plouffe, D.; SLAC

2005-01-01

The Final Focus Test Beam (FFTB) was conceived as a technological stepping stone on the way to the next linear collider. Nowhere is this more evident than with the alignment subsystems. Alignment tolerances for components prior to beam turn are almost an order of magnitude smaller than for previous projects at SLAC. Position monitoring systems which operate independent of the beam are employed to monitor motions of the components locally and globally with unprecedented precision. An overview of the FFTB alignment system is presented herein

Strain differentiation of polioviruses with monoclonal antibodies.

NARCIS (Netherlands)

A.D.M.E. Osterhaus (Albert); A.L. van Wezel; A.J.H. Stegmann; J.A.A.M. van Asten (Jack)

1984-01-01

textabstractPanels of monoclonal antibodies raised against different poliovirus type 1, 2 and 3 strains, were tested in a micro-neutralization test and in a micro-enzyme linked immunosorbent assay against a large number of poliovirus strains. The results were compared with those obtained with the

Bacteriocin-like inhibitory activities of seven Lactobacillus delbrueckii subsp. bulgaricus strains against antibiotic susceptible and resistant Helicobacter pylori strains.

Science.gov (United States)

Boyanova, L; Gergova, G; Markovska, R; Yordanov, D; Mitov, I

2017-12-01

The aim of the study was to detect anti-Helicobacter pylori activity of seven Lactobacillus delbrueckii subsp. bulgaricus (GLB) strains by four cell-free supernatant (CFS) types. Activity of non-neutralized and non-heat-treated (CFSs1), non-neutralized and heat-treated (CFSs2), pH neutralized, catalase-treated and non-heat-treated (CFSs3), or neutralized, catalase- and heat-treated (CFSs4) CFSs against 18 H. pylori strains (11 of which with antibiotic resistance) was evaluated. All GLB strains produced bacteriocin-like inhibitory substances (BLISs), the neutralized CFSs of two GLB strains inhibited >81% of test strains and those of four GLB strains were active against >71% of antibiotic resistant strains. Two H. pylori strains were BLIS resistant. The heating did not reduce the CFS activity. Briefly, all GLB strains evaluated produced heat-stable BLISs, although GLB and H. pylori strain susceptibility patterns exhibited differences. Bacteriocin-like inhibitory substance activity can be an advantage for the probiotic choice for H. pylori infection control. In this study, anti-Helicobacter pylori activity of seven Lactobacillus delbrueckii subsp. bulgaricus (GLB) strains was evaluated by four cell-free supernatant (CFS) types. The GLB strains produced heat-stable bacteriocin-like inhibitory substances (BLISs) with a strong anti-H. pylori activity and some neutralized, catalase- and heat-treated CFSs inhibited >83% of the test strains. Bacteriocin-like inhibitory substance production of GLB strains can render them valuable probiotics in the control of H. pylori infection. © 2017 The Society for Applied Microbiology.

Application of a fiber optic grating strain sensor for the measurement of strain under irradiation environment

International Nuclear Information System (INIS)

Kaji, Yoshiyuki; Matsui, Yoshinori; Kita, Satoshi; Ide, Hiroshi; Tsukada, Takashi; Tsuji, Hirokazu

2002-01-01

In the Japan Atomic Energy Research Institute (JAERI), in-pile strain measurement techniques have been developed using the Japan Materials Testing Reactor (JMTR). In order to evaluate the performance of fiber optic grating sensors under irradiation environment, heat-up and performance tests at elevated temperatures before irradiation and in-pile tests were performed in JMTR. It was determined that it is possible to measure strain under irradiation environment below 1x10 23 n m -2 (E>1 MeV) by a fiber optic grating sensor, because in-pile temperature characteristics were in good agreement with out-of-pile test results

Instrument for measuring fuel cladding strain

International Nuclear Information System (INIS)

Billeter, T.R.

1976-01-01

Development work to provide instrumentation for the continuous measurement of strain of material specimens such as nuclear fuel cladding has shown that a microwave sensor and associated instrumentation hold promise. The cylindrical sensor body enclosing the specimen results in a coaxial resonator absorbing microwave energy at frequencies dependent upon the diameter of the specimen. Diametral changes of a microinch can be resolved with use of the instrumentation. Very reasonable values of elastic strain were measured at 75 0 F and 1000 0 F for an internally pressurized 20 percent C.W. 316 stainless steel specimen simulating nuclear fuel cladding. The instrument also indicated the creep strain of the same specimen pressurized at 6500 psi and at a temperature of 1000 0 F for a period of 700 hours. Although the indicated strain appears greater than actual, the sensor/specimen unit experienced considerable oxidation even though an inert gas purge persisted throughout the test duration. By monitoring at least two modes of resonance, the measured strain was shown to be nearly independent of sensor temperature. To prevent oxidation, a second test was performed in which the specimen/sensor units were contained in an evacuated enclosure. The strain of the two prepressurized specimens as indicated by the microwave instrumentation agreed very closely with pre- and post-test measurements obtained with use of a laser interferometer

Determination of dehydrogenase activities involved in D-glucose oxidation in Gluconobacter and Acetobacter strains

Directory of Open Access Journals (Sweden)

Florencia Sainz

2016-08-01

Full Text Available Acetic acid bacteria (AAB are known for rapid and incomplete oxidation of an extensively variety of alcohols and carbohydrates, resulting in the accumulation of organic acids as the final products. These oxidative fermentations in AAB are catalyzed by PQQ- or FAD- dependent membrane bound dehydrogenases. In the present study, the enzyme activity of the membrane bound dehydrogenases (membrane-bound PQQ-glucose dehydrogenase (mGDH, D-gluconate dehydrogenase (GADH and membrane-bound glycerol dehydrogenase (GLDH involved in the oxidation of D-glucose and D-gluconic acid (GA was determined in six strains of three different species of AAB (three natural and three type strains. Moreover, the effect of these activities on the production of related metabolites (GA, 2-keto-D-gluconic acid (2KGA and 5-keto-D-gluconic acid (5KGA was analyzed. The natural strains belonging to Gluconobacter showed a high mGDH activity and low activity in GADH and GLDH, whereas the A. malorum strain presented low activity in the three enzymes. Nevertheless, no correlation was observed between the activity of these enzymes and the concentration of the corresponding metabolites. In fact, all the tested strains were able to oxidize D-glucose to GA, being maximal at the late exponential phase of the AAB growth (24 h, which coincided with glucose exhaustion and the maximum mGDH activity. Instead, only some of the tested strains were capable of producing 2KGA and/or 5KGA. In the case of G. oxydans strains, no 2KGA production was detected which is related to the absence of GADH activity after 24 h, while in the remaining strains, detection of GADH activity after 24h resulted in a high accumulation of 2KGA. Therefore, it is possible to choose the best strain depending on the desired product composition.Moreover, the sequences of these genes were used to construct phylogenetic trees. According to the sequence of gcd, gene coding for mGDH, Acetobacter and Komagataeibacter were

Research on the Phenotypic Characterization of Mrsa Strains Isolated from Animals

Directory of Open Access Journals (Sweden)

Iulia Maria BUCUR

2017-05-01

Full Text Available Keywords: chromogen, methicillin, MRSA, resistance Introduction: Currently, both in staphylococci isolated from animals with different diseases, as well as in humans, the MRSA strains (Methicillin Resistant S. aureus are monitored, as the methicillin resistance is associated with the resistance to other antibiotic groups. Methicillin resistance is encoded by mec staphylococcal chromosomal cassettes (SCCmec, which are islands of resistance. These strains can be identified by molecular biology tests and tests that reveal several phenotypic characteristics. The research was made in order to characterize and identify phenotypically the MRSA staphylococci strains isolated from animals. Materials and Methods: Researches were made on 240 coagulase positive and coagulase negative strains of staphylococci. Mannitol fermentation was tested on Champan medium, free coagulase was revealed on Baird-Parker medium and to identify S. aureus subsp. aureus was used the chromogenic medium Chromatic Staph. Methicillin-resistant strains were detected by disc diffusion method, using biodiscs with methicillin, oxacillin and cefoxitin. Also, to identify the MRSA strains, was used the chromogenic medium Chromatic MRSA. Results: The isolates were positive to mannitol and produced complete haemolysis or were unhaemolytic. A total of 44 strains produced free coagulase on Baird-Parker medium, considered coagulase positive strains, while 196 were coagulase negative strains. The isolates conducted differently to methicillin: 22,08% of strains were resistant, 51,25% of strains were susceptible and 26,66% had intermediate resistance, while the resistant strains to oxacillin were 42,91%. The increased frequency of methicillin-resistant strains of staphylococci and, particularly, MRSA strains, determined using the cefoxitin disk diffusion test, which is more reliable than methicillin and oxacillin. On the MRSA chromogenic medium, the methicillin-resistant strains of staphylococci

Stress and strain measurements in solids

International Nuclear Information System (INIS)

Askegaard, V.

1978-01-01

A design basis is given for stress- and strain cells to be used in a solid either externally loaded or with a stressfree strain field (for example shrinkage). A stress- and a strain cell has been designed for use in granular materials. Calibration tests show either good or reasonably good correspondance with calculated values. (orig.) [de

Lactose-mediated carbon catabolite repression of putrescine production in dairy Lactococcus lactis is strain dependent.

Science.gov (United States)

del Rio, Beatriz; Ladero, Victor; Redruello, Begoña; Linares, Daniel M; Fernández, Maria; Martín, Maria Cruz; Alvarez, Miguel A

2015-06-01

Lactococcus lactis is the lactic acid bacterial (LAB) species most widely used as a primary starter in the dairy industry. However, several strains of L. lactis produce the biogenic amine putrescine via the agmatine deiminase (AGDI) pathway. We previously reported the putrescine biosynthesis pathway in L. lactis subsp. cremoris GE2-14 to be regulated by carbon catabolic repression (CCR) via glucose but not lactose (Linares et al., 2013). The present study shows that both these sugars repress putrescine biosynthesis in L. lactis subsp. lactis T3/33, a strain isolated from a Spanish artisanal cheese. Furthermore, we demonstrated that both glucose and lactose repressed the transcriptional activity of the aguBDAC catabolic genes of the AGDI route. Finally, a screening performed in putrescine-producing dairy L. lactis strains determined that putrescine biosynthesis was repressed by lactose in all the L. lactis subsp. lactis strains tested, but in only one L. lactis subsp. cremoris strain. Given the obvious importance of the lactose-repression in cheese putrescine accumulation, it is advisable to consider the diversity of L. lactis in this sense and characterize consequently the starter cultures to select the safest strains. Copyright © 2014 Elsevier Ltd. All rights reserved.

Haemophilus ducreyi Cutaneous Ulcer Strains Are Nearly Identical to Class I Genital Ulcer Strains.

Directory of Open Access Journals (Sweden)

Dharanesh Gangaiah

Full Text Available Although cutaneous ulcers (CU in the tropics is frequently attributed to Treponema pallidum subspecies pertenue, the causative agent of yaws, Haemophilus ducreyi has emerged as a major cause of CU in yaws-endemic regions of the South Pacific islands and Africa. H. ducreyi is generally susceptible to macrolides, but CU strains persist after mass drug administration of azithromycin for yaws or trachoma. H. ducreyi also causes genital ulcers (GU and was thought to be exclusively transmitted by microabrasions that occur during sex. In human volunteers, the GU strain 35000HP does not infect intact skin; wounds are required to initiate infection. These data led to several questions: Are CU strains a new variant of H. ducreyi or did they evolve from GU strains? Do CU strains contain additional genes that could allow them to infect intact skin? Are CU strains susceptible to azithromycin?To address these questions, we performed whole-genome sequencing and antibiotic susceptibility testing of 5 CU strains obtained from Samoa and Vanuatu and 9 archived class I and class II GU strains. Except for single nucleotide polymorphisms, the CU strains were genetically almost identical to the class I strain 35000HP and had no additional genetic content. Phylogenetic analysis showed that class I and class II strains formed two separate clusters and CU strains evolved from class I strains. Class I strains diverged from class II strains ~1.95 million years ago (mya and CU strains diverged from the class I strain 35000HP ~0.18 mya. CU and GU strains evolved under similar selection pressures. Like 35000HP, the CU strains were highly susceptible to antibiotics, including azithromycin.These data suggest that CU strains are derivatives of class I strains that were not recognized until recently. These findings require confirmation by analysis of CU strains from other regions.

Description of near-tip fracture processes in strain hardening cementitious composites using image-based analysis and the compact tension test

DEFF Research Database (Denmark)

Pereira, Eduardo B.; Fischer, Gregor; Barros, Joaquim A.O.

2013-01-01

The cracking mechanisms assume a key role in the composite behavior of Strain Hardening Cementitious Composites (SHCCs). Due to their importance, in previous studies the mechanical behavior of SHCC materials, as well as of other strain softening fiber reinforced cementitious composites......, was characterized under eccentric tensile loading using the Compact Tension Test (CTT). The present research further extends this investigation, with particular emphasis on cementitious composites reinforced with multiple types of fibers. The experimental tensile load-displacement results are discussed and compared...

Effect of axial tibial torque direction on ACL relative strain and strain rate in an in vitro simulated pivot landing.

Science.gov (United States)

Oh, Youkeun K; Kreinbrink, Jennifer L; Wojtys, Edward M; Ashton-Miller, James A

2012-04-01

Anterior cruciate ligament (ACL) injuries most frequently occur under the large loads associated with a unipedal jump landing involving a cutting or pivoting maneuver. We tested the hypotheses that internal tibial torque would increase the anteromedial (AM) bundle ACL relative strain and strain rate more than would the corresponding external tibial torque under the large impulsive loads associated with such landing maneuvers. Twelve cadaveric female knees [mean (SD) age: 65.0 (10.5) years] were tested. Pretensioned quadriceps, hamstring, and gastrocnemius muscle-tendon unit forces maintained an initial knee flexion angle of 15°. A compound impulsive test load (compression, flexion moment, and internal or external tibial torque) was applied to the distal tibia while recording the 3D knee loads and tibofemoral kinematics. AM-ACL relative strain was measured using a 3 mm DVRT. In this repeated measures experiment, the Wilcoxon signed-rank test was used to test the null hypotheses with p < 0.05 considered significant. The mean (±SD) peak AM-ACL relative strains were 5.4 ± 3.7% and 3.1 ± 2.8% under internal and external tibial torque, respectively. The corresponding mean (± SD) peak AM-ACL strain rates reached 254.4 ± 160.1%/s and 179.4 ± 109.9%/s, respectively. The hypotheses were supported in that the normalized mean peak AM-ACL relative strain and strain rate were 70 and 42% greater under internal than under external tibial torque, respectively (p = 0.023, p = 0.041). We conclude that internal tibial torque is a potent stressor of the ACL because it induces a considerably (70%) larger peak strain in the AM-ACL than does a corresponding external tibial torque. Copyright © 2011 Orthopaedic Research Society.

Improving sensitivity of the polyurethane/CNT laminate strain sensor by controlled mechanical preload

International Nuclear Information System (INIS)

Slobodian, Petr; Olejnik, Robert; Matyas, Jiri; Babar, Dipak Gorakh

2016-01-01

This article describes strain detection potential of polyurethane/CNT layered composite and further possible enhance of its sensitivity to strain, expressed by value of gauge factor, GF, employing its controlled mechanical preload. In course of its fabrication a non-woven polyurethane membrane made by electro spinning was used as filtering membrane for CNT aqueous dispersion. Final CNT polyurethane laminate composite is prepared by compression molding. Produced polyurethane/CNT composite laminate is electrically conductive and high elastic. Its elongation leads to change of its macroscopic electrical resistance. Changes in resistance are further reversible, reproducible and can monitor deformation in real time. Gauge factor reaches very high values around 8 for strain reaching 3.5% comparing with conventional metallic strain gauges. Finally, controlled mechanical preload significantly increases value of GF. For example for value of 8.1% of preload value of GF reaches 23.3 for strain 3.5%. (paper)

Differences between strains of Rhizobium in sensitivity to canavanine

Energy Technology Data Exchange (ETDEWEB)

Weaks, T E [Marshall Univ., Huntingdon, West Virginia (USA). Dept. of Biological Sciences

1977-11-01

Four strains of rhizobia that nodulate canavanine-synthesizing legumes and four strains that nodulate noncanavanine-synthesizing legumes were tested for sensitivity to L-canavanine. The effect of canavanine on growth depends upon the strain of Rhizobium tested rather than the canavanine synthesizing capability of the host legume. In both groups of rhizobia, some strains were inhibited in growth by canavanine. Canavanine enhancement of growth was observed in rhizobia that nodulate noncanavanine-synthesizing legumes. Canavanine was found to enhance the incorporation of /sup 3/H-uridine and /sup 3/H-L-leucine into trichloroacetic acid insoluble fractions of starved cells of two strains of rhizobia tested. This demonstrated that under certain conditions, some rhizobia can detoxify canavanine and utilize it in synthetic processes.

[Identification of Candida dubliniensis strains using heat tolerance tests, morphological characteristics and molecular methods].

Science.gov (United States)

Arikan, Sevtap; Darka, Ozge; Hasçelik, Gülşen; Günalp, Ayfer

2003-01-01

Described in 1995, Candida dubliniensis is a novel Candida species closely related to Candida albicans due primarily to its ability to produce germ tube and chlamydospores. Given these phenotypic similarities between the two species, C. dubliniensis cannot be readily distinguished from Candida albicans by routine laboratory work-up. We explored the frequency of isolation of C. dubliniensis among 213 strains previously defined as C. albicans based on their ability to produce germ tube. The test isolates were initially examined for their morphological features on cornmeal tween 80 agar, inability to grow at 45 degrees C, and the biochemical assimilation profile (ID 32C system, bioMerieux, France). Among all, 2 (0.9%) of the isolates were identified as C. dubliniensis based on the production of numerous chlamydospores in chains on cornmeal tween 80 agar and the lack of growth at 45 degrees C. The assimilation profile of these isolates was found to be in accordance with this identification. In an effort to confirm the identification, polymerase chain reaction (PCR) studies were carried out by using the C. dubliniensis specific primer set, DUBF and DUBR. Both of the isolates yielded C. dubliniensis-specific 288 base pair amplification products, confirming the previous identification obtained with the initial screening tests. The isolates were found to be susceptible to fluconazole and itraconazole, and generated amphotericin B minimal inhibitory concentrations of 0.5-1 microgram/ml by NCCLS M27-A2 microdilution method. These data suggest that the isolation rate of C. dubliniensis among our clinical isolates is low. The morphological features on cornmeal tween 80 agar and the lack of ability to grow at 45 degrees C appear as reliable, cheap, and practical screening tests in initial identification of C. dubliniensis among germ tube-producing Candida strains.

Characterisation of the thermostable protease AprX in strains of Pseudomonas fluorescens and impact on the shelf-life of dairy products: preliminary results

Directory of Open Access Journals (Sweden)

Nadia Andrea Andreani

2016-12-01

Full Text Available Bacterial proteases are involved in food spoilage and shelf-life reduction. Among the bacterial proteases, a predominant role in spoilage of dairy products seems to be played by the thermostable metallo-protease AprX, which is produced by various strains of Pseudomonas fluorescens. Differences in AprX enzyme activity among different strains were highlighted, but the most proteolytic strains were not identified. In this study, the presence of the aprX gene was evaluated in 69 strains isolated from food matrices and 18 reference strains belonging to the P. fluorescens group, which had been previously typed by the multi locus sequence typing method. Subsequently, a subset of reference strains was inoculated in ultra-high temperature milk, and the expression of the aprX gene was evaluated at 22 and 6°C. On the same milk samples, the proteolytic activity was then evaluated through Azocasein and trinitrobenzenesulfonic acid solution assays. Finally, to assess the applicability of the former assay directly on dairy products the proteolityc activity was tested on industrial ricotta samples using the Azocasein assay. These results demonstrate the spread of aprX gene in most strains tested and the applicability of Azocasein assay to monitor the proteolytic activity in dairy products.

Stress strain flow curves for Cu-OFP

International Nuclear Information System (INIS)

Sandstroem, Rolf; Hallgren, Josefin

2009-04-01

Stress strain curves of oxygen free copper alloyed with phosphorus Cu-OFP have been determined in compression and tension. The compression tests were performed at room temperature for strain rates between 10 -5 and 10 -3 1/s. The tests in tension covered the temperature range 20 to 175 deg C for strain rates between 10 -7 and 5x10 -3 1/s. The results in compression and tension were close for similar strain rates. A model for stress strain curves has been formulated using basic dislocation mechanisms. The model has been set up in such a way that fitting of parameters to the curves is avoided. By using a fundamental creep model as a basis a direct relation to creep data has been established. The maximum engineering flow stress in tension is related to the creep stress giving the same strain rate. The model reproduces the measured flow curves as function of temperature and strain rate in the investigated interval. The model is suitable to use in finite-element computations of structures in Cu-OFP

Screening lactic acid bacteria strains with ability to bind di-n-butyl phthalate via Turbiscan technique.

Science.gov (United States)

Lili, Zhao; Hongfei, Zhao; Shoukat, Sana; Xiaochen, Zhang; Bolin, Zhang

2017-06-01

Di-n-butyl phthalate (DBP) is a ubiquitous environmental contaminant that poses a risk to humans. Previous work indicates that the ability of lactic acid bacteria (LAB) to bind phthalic acid esters is strain-specific. As cell suspensions of LAB strains in aqueous solution are likely to be colloidal dispersions, this study provided a technique to efficiently screen LAB strains that bind DBP via Turbiscan, which has been widely used to measure the stability of emulsions or colloidal dispersions. Eleven LAB strains belonging to Lactobacillus plantarum, Lb. pentosus, Lb. paralimentarius, Lb. helveticus, Leuconostoc mesenteroides, Lb. acidophilus, Bifidobacterium lactis, and Bifidobacterium bifidum species were used in this study, and seven of them were selected to test in an earlier stage of exploring the process for finding a screening method; others were used for a validation test. It was observed that the various values of the 10 h Turbiscan Stability Index (TSI) of the cell suspension from each strain, at the equilibrium time of dispersed particles according to the peak thickness of cell-suspensions as measured by Turbiscan, had significant negative correlations with the DBP-binding percentage of LAB strains. Higher TSI values are correlated with lower binding of bacteria strains to DBP with a correlation coefficient of 0.8292. Cell surface hydrocarbons of LAB strains and their adherence were observed to correlate with DBP-binding percentages and may lead to the different states of aggregation or equilibrium of bacterial cell-suspensions, and the aggregation of bacterial cells resulted in fewer binding sites in the cell wall for DBP. Finally, four LAB strains were randomly selected to verify the feasibility of the method. In all, the findings demonstrate that TSI might be used as a tool to quickly screen strains that bind DBP. The present work could be extended to the removal of other toxic compounds, when screening of high-efficiency strains is required.

Peri-Implant Strain in an In Vitro Model.

Science.gov (United States)

Hussaini, Souheil; Vaidyanathan, Tritala K; Wadkar, Abhinav P; Quran, Firas A Al; Ehrenberg, David; Weiner, Saul

2015-10-01

An in vitro experimental model was designed and tested to determine the influence that peri-implant strain may have on the overall crestal bone. Strain gages were attached to polymethylmethacrylate (PMMA) models containing a screw-type root form implant at sites 1 mm from the resin-implant interface. Three different types of crown superstructures (cemented, 1-screw [UCLA] and 2-screw abutment types) were tested. Loading (1 Hz, 200 N load) was performed using a MTS Mechanical Test System. The strain gage data were stored and organized in a computer for statistical treatment. Strains for all abutment types did not exceed the physiological range for modeling and remodeling of cancellous bone, 200-2500 με (microstrain). For approximately one-quarter of the trials, the strain values were less than 200 με the zone for bone atrophy. The mean microstrain obtained was 517.7 με. In conclusion, the peri-implant strain in this in vitro model did not exceed the physiologic range of bone remodeling under axial occlusal loading.

Comprehensive update of dalbavancin activity when tested against uncommonly isolated streptococci, Corynebacterium spp., Listeria monocytogenes, and Micrococcus spp. (1357 strains).

Science.gov (United States)

Jones, Ronald N; Stilwell, Matthew G

2013-06-01

Dalbavancin is an investigational lipoglycopeptide having an extended serum elimination half-life allowing once-weekly dosing. Data from testing 1357 strains of uncommonly isolated species expand the dalbavancin spectrum details as follows (MIC50/90): β-haemolytic streptococcal serogroups C, F, and G (≤0.03/≤0.03 μg/mL), 7 viridans group of streptococci (≤0.03/≤0.03-0.06 μg/mL), 5 Corynebacterium spp. (0.06/0.12 μg/mL), Listeria monocytogenes (0.06/0.12 μg/mL), and Micrococcus spp. (≤0.03/≤0.03 μg/mL). Among all reported isolates, 99.8% of tested strains were inhibited at dalbavancin MIC values at ≤0.12 μg/mL. Dalbavancin remains very potent against rarer Gram-positive pathogens, using in vitro test experience with organisms cultured through 2011. Copyright © 2013 Elsevier Inc. All rights reserved.

Experimental characterization and modelling of UO2 mechanical behaviour at high temperatures and high strain rates

International Nuclear Information System (INIS)

Salvo, Maxime

2014-01-01

The aim of this work is to characterize and model the mechanical behavior of uranium dioxide (UO 2 ) during a Reactivity Initiated Accident (RIA). The fuel loading during a RIA is characterized by high strain rates (up to 1/s) and high temperatures (1000 C - 2500 C). Two types of UO 2 pellets (commercial and high density) were therefore tested in compression with prescribed displacement rates (0.1 to 100 mm/min corresponding to strain rates of 10 -4 - 10 -1 /s) and temperatures (1100 C - 1350 C - 1550 C et 1700 C). Experimental results (geometry, yield stress and microstructure) allowed us to define a hyperbolic sine creep law and a Drucker-Prager criterion with associated plasticity, in order to model grain boundaries fragmentation at the macroscopic scale. Finite Element Simulations of these tests and of more than 200 creep tests were used to assess the model response to a wide range of temperatures (1100 C - 1700 C) and strain rates (10 -9 /s - 10 -1 /s). Finally, a constitutive law called L3F was developed for UO 2 by adding to the previous model irradiation creep and tensile macroscopic cracking. The L3F law was then introduced in the 1.5D scheme of the fuel performance code ALCYONE-RIA to simulate the REP-Na tests performed in the experimental reactor CABRI. Simulation results are in good agreement with post tests examinations. (author) [fr

Final comparison report on ISP-35: Nupec hydrogen mixing and distribution test (Test M-7-1)

International Nuclear Information System (INIS)

1994-12-01

This final comparison report summarizes the results of the OECD/CSNI sponsored ISP-35 exercise which was based on NUPEC's Hydrogen Mixing and Distribution Test M-7-1. 12 organizations from 10 different countries took part in the exercise. For the ISP-35 test, a steam/light gas (helium) mixture was released into the lower region of a simplified model of a PWR containment. At the same time, the dome cooling spray was also activated. the transient time histories for gas temperature and concentrations were recorded for each of the 25 compartments of the model containment. The wall temperatures as well as the dome pressure were also recorded. The ISP-35 participants simulated the test conditions and attempted to predict the time histories using their accident analysis codes. Results of these analyses are presented, and comparisons are made between the experimental data and the calculated data. In general, predictions for pressure, helium concentration and gas distribution patterns were achieved with acceptable accuracy

Strain rate measurement by Electronic Speckle Pattern Interferometry: A new look at the strain localization onset

International Nuclear Information System (INIS)

Guelorget, Bruno; Francois, Manuel; Vial-Edwards, Cristian; Montay, Guillaume; Daniel, Laurent; Lu, Jian

2006-01-01

In-plane Electronic Speckle Pattern Interferometry has been successfully used during tensile testing of semi-hard copper sheets in order to measure the strain rate. On one hand, heterogeneity in strain rate field has been found before the maximum of the tensile force (ε t ≅ 19.4 and 25.4%, respectively). Thus, a localization phenomenon occurs before the classic Considere's criterion (dF = 0) for the diffuse neck initiation. On the other hand, strain rate measurement before fracture shows the moment where one of the two slip band systems becomes predominant, then strain concentrates in a small area, the shear band. Uncertainty evaluation has been carried out, which shows a very good accuracy of the total strain and the strain rate measurements

Strain rate measurement by Electronic Speckle Pattern Interferometry: A new look at the strain localization onset

Energy Technology Data Exchange (ETDEWEB)

Guelorget, Bruno [Universite de Technologie de Troyes (UTT), Laboratoire des Systemes Mecaniques et d' ingenierie Simultanee (LASMIS, CNRS FRE 2719), 12 rue Marie Curie, B.P. 2060, 10010 Troyes Cedex (France)]. E-mail: bruno.guelorget@utt.fr; Francois, Manuel [Universite de Technologie de Troyes (UTT), Laboratoire des Systemes Mecaniques et d' ingenierie Simultanee (LASMIS, CNRS FRE 2719), 12 rue Marie Curie, B.P. 2060, 10010 Troyes Cedex (France); Vial-Edwards, Cristian [Departemento de Ingenieria Mecanica y Metalurgica, Pontificia Universidad Catolica de Chile, Vicuna Mackenna 4860, 6904411 Santiago (Chile); Montay, Guillaume [Universite de Technologie de Troyes (UTT), Laboratoire des Systemes Mecaniques et d' ingenierie Simultanee (LASMIS, CNRS FRE 2719), 12 rue Marie Curie, B.P. 2060, 10010 Troyes Cedex (France); Daniel, Laurent [Universite de Technologie de Troyes (UTT), Laboratoire des Systemes Mecaniques et d' ingenierie Simultanee (LASMIS, CNRS FRE 2719), 12 rue Marie Curie, B.P. 2060, 10010 Troyes Cedex (France); Lu, Jian [Universite de Technologie de Troyes (UTT), Laboratoire des Systemes Mecaniques et d' ingenierie Simultanee (LASMIS, CNRS FRE 2719), 12 rue Marie Curie, B.P. 2060, 10010 Troyes Cedex (France)

2006-01-15

In-plane Electronic Speckle Pattern Interferometry has been successfully used during tensile testing of semi-hard copper sheets in order to measure the strain rate. On one hand, heterogeneity in strain rate field has been found before the maximum of the tensile force ({epsilon} {sup t} {approx_equal} 19.4 and 25.4%, respectively). Thus, a localization phenomenon occurs before the classic Considere's criterion (dF = 0) for the diffuse neck initiation. On the other hand, strain rate measurement before fracture shows the moment where one of the two slip band systems becomes predominant, then strain concentrates in a small area, the shear band. Uncertainty evaluation has been carried out, which shows a very good accuracy of the total strain and the strain rate measurements.

Damage Assessment of Heat Resistant Steels through Electron BackScatter Diffraction Strain Analysis under Creep and Creep-Fatigue Conditions

Science.gov (United States)

Fujiyama, Kazunari; Kimachi, Hirohisa; Tsuboi, Toshiki; Hagiwara, Hiroyuki; Ogino, Shotaro; Mizutani, Yoshiki

EBSD(Electron BackScatter Diffraction) analyses were conducted for studying the quantitative microstructural metrics of creep and creep-fatigue damage for austenitic SUS304HTB boiler tube steel and ferritic Mod.9Cr piping steel. KAM(Kernel Average Misorientation) maps and GOS(Grain Orientation Spread) maps were obtained for these samples and the area averaged values KAMave and GOSave were obtained. While the increasing trends of these misorientation metrics were observed for SUS304HTB steel, the decreasing trends were observed for damaged Mod.9Cr steel with extensive recovery of subgrain structure. To establish more universal parameter representing the accumulation of damage to compensate these opposite trends, the EBSD strain parameters were introduced for converting the misorientation changes into the quantities representing accumulated permanent strains during creep and creep-fatigue damage process. As KAM values were dependent on the pixel size (inversely proportional to the observation magnification) and the permanent strain could be expressed as the shear strain which was the product of dislocation density, Burgers vector and dislocation movement distance, two KAM strain parameters MεKAMnet and MεδKAMave were introduced as the sum of product of the noise subtracted KAMnet and the absolute change from initial value δKAMave with dislocation movement distance divided by pixel size. MεδKAMave parameter showed better relationship both with creep strain in creep tests and accumulated creep strain range in creep-fatigue tests. This parameter can be used as the strain-based damage evaluation and detector of final failure.

A wide extent of inter-strain diversity in virulent and vaccine strains of alphaherpesviruses.

Science.gov (United States)

Szpara, Moriah L; Tafuri, Yolanda R; Parsons, Lance; Shamim, S Rafi; Verstrepen, Kevin J; Legendre, Matthieu; Enquist, L W

2011-10-01

Alphaherpesviruses are widespread in the human population, and include herpes simplex virus 1 (HSV-1) and 2, and varicella zoster virus (VZV). These viral pathogens cause epithelial lesions, and then infect the nervous system to cause lifelong latency, reactivation, and spread. A related veterinary herpesvirus, pseudorabies (PRV), causes similar disease in livestock that result in significant economic losses. Vaccines developed for VZV and PRV serve as useful models for the development of an HSV-1 vaccine. We present full genome sequence comparisons of the PRV vaccine strain Bartha, and two virulent PRV isolates, Kaplan and Becker. These genome sequences were determined by high-throughput sequencing and assembly, and present new insights into the attenuation of a mammalian alphaherpesvirus vaccine strain. We find many previously unknown coding differences between PRV Bartha and the virulent strains, including changes to the fusion proteins gH and gB, and over forty other viral proteins. Inter-strain variation in PRV protein sequences is much closer to levels previously observed for HSV-1 than for the highly stable VZV proteome. Almost 20% of the PRV genome contains tandem short sequence repeats (SSRs), a class of nucleic acids motifs whose length-variation has been associated with changes in DNA binding site efficiency, transcriptional regulation, and protein interactions. We find SSRs throughout the herpesvirus family, and provide the first global characterization of SSRs in viruses, both within and between strains. We find SSR length variation between different isolates of PRV and HSV-1, which may provide a new mechanism for phenotypic variation between strains. Finally, we detected a small number of polymorphic bases within each plaque-purified PRV strain, and we characterize the effect of passage and plaque-purification on these polymorphisms. These data add to growing evidence that even plaque-purified stocks of stable DNA viruses exhibit limited sequence

Computer-aided dispatch--traffic management center field operational test : state of Utah final report

Science.gov (United States)

2006-07-01

This document provides the final report for the evaluation of the USDOT-sponsored Computer-Aided Dispatch Traffic Management Center Integration Field Operations Test in the State of Utah. The document discusses evaluation findings in the followin...

Dynamic behavior and microstructural evolution during moderate to high strain rate hot deformation of a Fe–Ni–Cr alloy (alloy 800H)

International Nuclear Information System (INIS)

Cao, Yu; Di, Hongshuang; Zhang, Jiecen; Yang, Yaohua

2015-01-01

The objective of the study is to fundamentally understand the dynamic behavior of alloy 800H at moderate to high strain rate using hot compression tests and propose nucleation mechanism associated with dynamic crystallization (DRX). We firstly investigated the dynamic behavior of alloy 800H with industrial scale strain rates using hot compression tests and adiabatic correction was performed to correct as-measured flow curves. Secondly, a Johnson–Cook model was established by using the corrected data and could give a precise prediction of elevated temperature flow stress for the studied alloy. Finally, the nucleation mechanism of DRX grains at high strain rates was studied. The results showed that the predominant nucleation mechanism for DRX is the formation of “bulge” at parent grain boundary. Additionally, the fragmentation of original grain at low deformation temperatures and the twinning near the bulged regions at high deformation temperatures also accelerate the DRX process

Dynamic behavior and microstructural evolution during moderate to high strain rate hot deformation of a Fe-Ni-Cr alloy (alloy 800H)

Science.gov (United States)

Cao, Yu; Di, Hongshuang; Zhang, Jiecen; Yang, Yaohua

2015-01-01

The objective of the study is to fundamentally understand the dynamic behavior of alloy 800H at moderate to high strain rate using hot compression tests and propose nucleation mechanism associated with dynamic crystallization (DRX). We firstly investigated the dynamic behavior of alloy 800H with industrial scale strain rates using hot compression tests and adiabatic correction was performed to correct as-measured flow curves. Secondly, a Johnson-Cook model was established by using the corrected data and could give a precise prediction of elevated temperature flow stress for the studied alloy. Finally, the nucleation mechanism of DRX grains at high strain rates was studied. The results showed that the predominant nucleation mechanism for DRX is the formation of "bulge" at parent grain boundary. Additionally, the fragmentation of original grain at low deformation temperatures and the twinning near the bulged regions at high deformation temperatures also accelerate the DRX process.

Investigations of multiresistance to antibiotics and chemotherapeutics and extended spectrum beta: Lactamase effect (ESBL test in strains E.coli and salmonella originating from domestic animals

Directory of Open Access Journals (Sweden)

Mišić Dušan

2006-01-01

Full Text Available The presence of multiresistance to the effects of antibiotics and chemotherapeutics and extended spectrum beta-lactamase were examined in 45 strains of E. coli and 35 strains of Salmonella. The strains of E. coli originated from several species of domestic animals: dogs, cats, poultry, and cattle, and 30 strains of Salmonella originated from poultry, 4 strains from cattle, and 1 strain from swine. The presence of the following serovarieties was established using serological examinations: Salmonella Enteritidis 17 strains, Salmonella Gallinarum 1 strain, Salmonella Hartford 5 strains, Salmonella Anatum 1 strain, Salmonella Typhimurium 4 strains, Salmonella Agona 1 strain, Salmonella Infantis 1 strain, Salmonella Thompson var. Berlin 1 strain, Salmonella Tennessee 1 strain, Salmonella Senftenberg 1 strain, Salmonella Glostrup 1 strain, and Salmonella Hadar 1 strain. In the examinations of the listed strains we used antibiogram discs of ampicillin, amoxicillin with clavulanic acid, cephalexin, cephtriaxon, cephotaxim, cephtazidime, aztreonam, gentamycin, chloramphenicol, tetracycline, cyprofloxacine, and a combination of sulphamethoxasole and trimethoprim. The lowest prevalence of multiresistance in E. Coli strains to 3 or more antibiotics was established in dogs 20%, and the highest in 60% strains originating from swine. In 62.88% strains of Salmonella we established sensitivity to all applied antibiotics. Resistance was also established in a small number of the examined strains to ampicillin (11 strains, to tetracycline (5 strains, to amoxicillin with clavulanic acid (5 strains, to sulphamethoxasole with trimethoprim (5 strains, to gentamycin (3 strains, and to cloramphenicol (1 strain. Of all the examined strains of Salmonella, 6 strains originating from poultry exhibited multiresistence. The presence of extended spectrum beta-lactamase effects examined using the ESBL test, was not established in strains of E. coli and Salmonella strains.

Construction and test of the final CMS Barrel Drift Tube Muon Chamber prototype

Energy Technology Data Exchange (ETDEWEB)

Aguilar-Benitez, M.; Alberdi, J.; Arneodo, M.; Banicz, K.; Benettoni, M.; Benvenuti, A.; Bethke, S.; Cerrada, M. E-mail: cerrada@ciemat.es; Cirio, R.; Colino, N.; Conti, E.; Dallavalle, M.; Daniel, M.; Dattola, D.; Daudo, F.; De Giorgi, M.; Dosselli, U.; Fanfani, A.; Fanin, C.; Fouz, M.C.; Gasparini, F.; Gasparini, U.; Giacomelli, P.; Giordano, V.; Gonella, F.; Grandi, C.; Guaita, P.; Guerzoni, M.; Lacaprara, S.; Lippi, I.; Marcellini, S.; Marin, J.; Martinelli, R.; Maselli, S.; Meneguzzo, A.; Migliore, E.; Mocholi, J.; Monaco, V.; Montanari, A.; Montanari, C.; Odorici, F.; Oller, J.C.; Paoletti, S.; Passaseo, M.; Pegoraro, M.; Peroni, C.; Puerta, J.; Reithler, H.; Romero, A.; Romero, L.; Ronchese, P.; Rossi, A.M.; Rovelli, T.; Sacchi, R.; Salicio, J.M.; Staiano, A.; Steinbeck, T.; Torassa, E.; Travaglini, R.; Ventura, L.; Ventura, S.; Vitelli, A.; Voetee, F.; Wegner, M.; Willmott, C.; Zotto, P.; Zumerle, G

2002-03-21

A prototype of the CMS Barrel Muon Detector incorporating all the features of the final chambers was built using the mass production assembly procedures and tools. The performance of this prototype was studied in a muon test beam at CERN and the results obtained are presented in this paper.

GTS Duratek, phase I Hanford low-level waste melter tests: Final report

International Nuclear Information System (INIS)

Eaton, W.C.

1995-01-01

A multiphase program was initiated in 1994 to test commercially available melter technologies for the vitrification of the low-level waste (LLW) stream from defense waste stored in underground tanks at the Hanford Site in southeastern Washington State. Phase 1 of the melter demonstration tests using simulated LLW was completed during fiscal year 1995. This document is the final report on testing performed by GTS Duratek Inc. in Columbia, Maryland. GTS Duratek (one of the seven vendors selected) was chosen to demonstrate Joule heated melter technology under WHC subcontract number MMI-SVV-384215. The report contains description of the tests, observations, test data and some analysis of the data as it pertains to application of this technology for LLW vitrification. The document also contains summaries of the melter offgas reports issued as separate documents for the 100 kg melter (WHC-SD-WM-VI-028) and for the 1000 kg melter (WHC-SD-WM-VI-029)

Grain orientation and strain measurements in sub-micron wide passivated individual aluminum test structures

International Nuclear Information System (INIS)

Tamura, N.; Valek, B.C.; Spolenak, R.; MacDowell, A.A.; Celestre, R.S.; Padmore, H.A.; Brown, W.L.; Marieb, T.; Bravman, J.C.; Batterman, B.W.; Patel, J.R.

2001-01-01

An X-ray microdiffraction dedicated beamline, combining white and monochromatic beam capabilities, has been built at the Advanced Light Source. The purpose of this beamline is to address the myriad of problems in Materials Science and Physics that require submicron x-ray beams for structural characterization. Many such problems are found in the general area of thin films and nano-materials. For instance, the ability to characterize the orientation and strain state in individual grains of thin films allows us to measure structural changes at a very local level. These microstructural changes are influenced heavily by such parameters as deposition conditions and subsequent treatment. The accurate measurement of strain gradients at the micron and sub-micron level finds many applications ranging from the strain state under nano-indenters to gradients at crack tips. Undoubtedly many other applications will unfold in the future as we gain experience with the capabilities and limitations of this instrument. We have applied this technique to measure grain orientation and residual stress in single grains of pure Al interconnect lines and preliminary results on post-electromigration test experiments are presented. It is shown that measurements with this instrument can be used to resolve the complete stress tensor (6 components) in a submicron volume inside a single grain of Al under a passivation layer with an overall precision of about 20 MPa. The microstructure of passivated lines appears to be complex, with grains divided into identifiable subgrains and noticeable local variations of both tensile/compressive and shear stresses within single grains

Active vibration control testing of the SPICES program: final demonstration article

Science.gov (United States)

Dunne, James P.; Jacobs, Jack H.

1996-05-01

The Synthesis and Processing of Intelligent Cost Effective Structures (SPICES) Program is a partnership program sponsored by the Advanced Research Projects Agency. The mission of the program is to develop cost effective material processing and synthesis technologies to enable new products employing active vibration suppression and control devices to be brought to market. The two year program came to fruition in 1995 through the fabrication of the final smart components and testing of an active plate combined with two trapezoidal rails, forming an active mount. Testing of the SPICES combined active mount took place at McDonnell Douglas facilities in St. Louis, MO, in October-December 1995. Approximately 15 dB reduction in overall response of a motor mounted on the active structure was achieved. Further details and results of the SPICES combined active mount demonstration testing are outlined. Results of numerous damping and control strategies that were developed and employed in the testing are presented, as well as aspects of the design and fabrication of the SPICES active mount components.

Childhood abuse and criminal behavior: testing a general strain theory model.

Science.gov (United States)

Watts, Stephen J; McNulty, Thomas L

2013-10-01

This article draws on general strain theory (GST) to develop and test a model of the childhood abuse-crime relationship. Using data from the National Longitudinal Study of Adolescent Health (Add Health),(1) we find that early childhood physical and sexual abuse are robust predictors of offending in adolescence, for the full sample and in equations disaggregated by gender. GST is partially supported in that the effects of childhood physical abuse on offending for both females and males are mediated by an index of depression symptoms, whereas the effect of sexual abuse among females appears to be mediated largely by closeness to mother. The effect of childhood sexual abuse among males, however, is more robust than among females and it persists despite controls for low self-control, ties to delinquent peers, school attachment, and closeness to mother. Theoretical implications of the findings are discussed.

Identification and characterisation of potential biofertilizer bacterial strains

Science.gov (United States)

Karagöz, Kenan; Kotan, Recep; Dadaşoǧlu, Fatih; Dadaşoǧlu, Esin

2016-04-01

In this study we aimed that isolation, identification and characterizations of PGPR strains from rhizosphere of legume plants. 188 bacterial strains isolated from different legume plants like clover, sainfoin and vetch in Erzurum province of Turkey. These three plants are cultivated commonly in the Erzurum province. It was screen that 50 out of 188 strains can fix nitrogen and solubilize phosphate. These strains were identified via MIS (Microbial identification system). According to MIS identification results, 40 out of 50 strains were identified as Bacillus, 5 as Pseudomonas, 3 as Paenibacillus, 1 as Acinetobacter, 1 as Brevibacterium. According to classical test results, while the catalase test result of all isolates are positive, oxidase, KOH and starch hydrolysis rest results are variable.

Mean strain effects on the random cyclic strain-life relations of 0Cr18Ni10Ti pipe steel

International Nuclear Information System (INIS)

Zhao Yongxiang; Yang Bing

2005-01-01

Experimental study is performed on the mean strain effects on the random cyclic strain-life relations of the new nuclear material, 0Cr18Ni10Ti pipe steel. In order to save costs of specimens and tests, an improved maximum likelihood fatigue test method is applied to manage the present strain-controlled fatigue tests. Six straining ratios, respectively, -1, -0.52, 0.22, 0.029, 0.18, and 0.48, are applied to study the effects. Total 104 specimens are fatigued. Since the material exhibits an entirely relaxation effect of mean stress under the six ratios and, in addition, there is no effectively method for the description of the mean straining effects under this case, previous Zhao's random strain-life relations are therefore applied for effective characterization of the scattering test data under the six ratios on a basis of Coffin-Manson equation.Then the effects of the ratios are analyzed respectively on the average fatigue lives, the standard deviations of the logarithms of fatigue lives, and the fatigue lives under different survival probabilities and confidences. The results reveal that the ratios greater than zero exhibit a positive effect of about 1.3 to 1.6 times under the survival probability of 0.999 and the confidence of 95%. A negative effect is exhibited for the case of the ratios less than zero. In addition, the assessment of the effects from the sense of average fatigue lives might result in a wrong conclusion for the practice of higher reliabilities. The effects can be appropriately assessed from a probabilistic sense to take into account the average lives, the scattering regularity of test data, and the size of sampling. (author)

The Role of Hydrogen-Enhanced Strain-Induced Lattice Defects on Hydrogen Embrittlement Susceptibility of X80 Pipeline Steel

Science.gov (United States)

Hattori, M.; Suzuki, H.; Seko, Y.; Takai, K.

2017-08-01

Studies to date have not completely determined the factors influencing hydrogen embrittlement of ferrite/bainite X80 pipeline steel. Hydrogen embrittlement susceptibility was evaluated based on fracture strain in tensile testing. We conducted a thermal desorption analysis to measure the amount of tracer hydrogen corresponding to that of lattice defects. Hydrogen embrittlement susceptibility and the amount of tracer hydrogen significantly increased with decreasing crosshead speed. Additionally, a significant increase in the formation of hydrogen-enhanced strain-induced lattice defects was observed immediately before the final fracture. In contrast to hydrogen-free specimens, the fracture surface of the hydrogen-charged specimens exhibited shallower dimples without nuclei, such as secondary phase particles. These findings indicate that the presence of hydrogen enhanced the formation of lattice defects, particularly just prior to the occurrence of final fracture. This in turn enhanced the formation of shallower dimples, thereby potentially causing premature fracture of X80 pipeline steel at lower crosshead speeds.

Five challenges in modelling interacting strain dynamics

Directory of Open Access Journals (Sweden)

Paul S. Wikramaratna

2015-03-01

Full Text Available Population epidemiological models where hosts can be infected sequentially by different strains have the potential to help us understand many important diseases. Researchers have in recent years started to develop and use such models, but the extra layer of complexity from multiple strains brings with it many technical challenges. It is therefore hard to build models which have realistic assumptions yet are tractable. Here we outline some of the main challenges in this area. First we begin with the fundamental question of how to translate from complex small-scale dynamics within a host to useful population models. Next we consider the nature of so-called “strain space”. We describe two key types of host heterogeneities, and explain how models could help generate a better understanding of their effects. Finally, for diseases with many strains, we consider the challenge of modelling how immunity accumulates over multiple exposures.

Radiation Tolerance Qualification Tests of the Final Source Interface Unit for the ALICE Experiment

CERN Document Server

Dénes, E; Futó, E; Kerék, A; Kiss, T; Molnár, J; Novák, D; Soós, C; Tölyhi, T; Van de Vyvre, P

2007-01-01

The ALICE Detector Data Link (DDL) is a high-speed optical link designed to interface the readout electronics of ALICE sub-detectors to the DAQ computers. The Source Interface Unit (SIU) of the DDL will operate in radiation environment. Previous tests showed that a configuration loss of SRAM-based FPGA devices may happen and the frequency of undetected data errors in the FPGA user memory area is also not acceptable. Therefore, we redesigned the SIU card using another FPGA based on flash technology. In order to detect bit errors in the user memory we added parity check logic to the design. The new SIU has been extensively tested using neutron and proton irradiation to verify its radiation tolerance. In this paper we summarize the design changes, introduce the final design, and the results of the radiation tolerance measurements on the final card.

Strain rate effects in stress corrosion cracking

Energy Technology Data Exchange (ETDEWEB)

Parkins, R.N. (Newcastle upon Tyne Univ. (UK). Dept. of Metallurgy and Engineering Materials)

1990-03-01

Slow strain rate testing (SSRT) was initially developed as a rapid, ad hoc laboratory method for assessing the propensity for metals an environments to promote stress corrosion cracking. It is now clear, however, that there are good theoretical reasons why strain rate, as opposed to stress per se, will often be the controlling parameter in determining whether or not cracks are nucleated and, if so, are propagated. The synergistic effects of the time dependence of corrosion-related reactions and microplastic strain provide the basis for mechanistic understanding of stress corrosion cracking in high-pressure pipelines and other structures. However, while this may be readily comprehended in the context of laboratory slow strain tests, its extension to service situations may be less apparent. Laboratory work involving realistic stressing conditions, including low-frequency cyclic loading, shows that strain or creep rates give good correlation with thresholds for cracking and with crack growth kinetics.

Assessment of adhesion properties of novel probiotic strains to human intestinal mucus.

Science.gov (United States)

Ouwehand, A C; Tuomola, E M; Tölkkö, S; Salminen, S

2001-02-28

Potential new probiotic strains Lactobacillus brevis PELI, L. reuteri ING1, L. rhamnosus VTT E-800 and L. rhamnosus LC-705 were assessed for their adhesion properties using the human intestinal mucus model. The effect on the adhesion of exposure to acid and pepsin and to milk were tested to simulate gastric and food processing conditions, and the effect of different growth media on adhesion was tested. The properties of the four strains were compared to the well-investigated probiotic L. rhamnosus strain GG. Three of the tested strains showed significant adhesion properties in the mucus model, while L. brevis PELI had intermediate adhesion and L. rhamnosus LC-705 adhered poorly. Pretreatment with different milks decreased the adhesion and low pH and pepsin treatment reduced the adhesion of all tested strains except L. rhamnosus LC-705. No competitive exclusion of pathogenic Salmonella typhimurium or Escherichia coli SfaII was observed. The results indicate that major differences exist between tested proposed probiotic strains. The growth media and the food matrix significantly affect the adhesive ability of the tested strains. This has previously not been taken into account when selecting novel probiotic strains.

Raman measurements of Kevlar-29 fiber pull-out test at different strain levels

Science.gov (United States)

Wang, Quan; Lei, Zhenkun; Kang, Yilan; Qiu, Wei

2008-11-01

This paper adopted Kevlar-29 fiber monofilament embedding technology to prepare fiber/ epoxy resin tensile specimen. The specimen was pulled on a homemade and portable mini-loading device. At the same time micro-Raman spectroscopy is introduced to detect the distributions of stress on the embedded fiber at different strain levels. The characteristic peak shift of the 1610 cm-1 in Raman band has a linear relationship with the strain or stress. The experimental results show that the fiber axial stress decreases gradually from the embedded fiber-start to the embedded fiber-end at the same strain level. At different strain levels, the fiber axial stress increases along with the applied load. It reveals that there is a larger fiber axial stress distribution under a larger strain level. And the stress transfer is realized gradually from the embedded fiber-start to the fiber-end. Stress concentration exists in the embedded fiber-end, which is a dangerous region for interfacial debonding easily.

Potential of functional strains, isolated from traditional Maasai milk, as starters for the production of fermented milks.

Science.gov (United States)

Patrignani, Francesca; Lanciotti, Rosalba; Mathara, Julius Maina; Guerzoni, Maria Elisabetta; Holzapfel, Wilhelm H

2006-03-01

The purpose of this research was the evaluation of technological features and of the ability of functional LAB strains with desirable sensory characteristics, to produce fermented milk. Eight strains of Lactobacillus plantarum, Lactobacillus acidophilus, Lactobacillus paracasei and Lactococcus lactis, isolated from Maasai traditional fermented milk in Kenya and previously tested for their probiotic properties, were selected for this investigation. Technological features such as growth kinetics in fresh heat-treated whole milk medium and survival in the final product during storage at 4 degrees C, were studied. The strains Lb. acidophilus BFE 6,059, Lb. paracasei BFE 5,264 and Lc. lactis BFE 6,049 showed the best potential and were thus selected for use as starter cultures in further trials with the objective to improve their technological performance and to optimise the sensory features of fermented milk obtained. The effects of fat (F), non-fat milk solids (S) and fermentation temperature (T), modulated according to a Central Composite Design, on fermentation rates and viability losses during refrigerated storage of the chosen starters, and on product texture parameters, were studied. From the data analysis, it was possible to select optimum conditions for enhancing positive sensory traits of final products and for improving the survival of these potentially probiotic cultures.

Study on strain transfer of embedded fiber Bragg grating sensors

Science.gov (United States)

Wu, Rujun; Zheng, Bailin; Fu, Kunkun; He, Pengfei; Tan, Yuegang

2014-08-01

In this study, a theoretical model of embedded fiber Bragg grating sensors was developed to provide predictions of the strain transfer rate and average strain transfer rate without the assumption that the host material is subjected to uniform axial stress. Further, a finite element (FE) analysis was performed to validate the present model. It was shown that the theoretical results with the present model are in good agreement with those by FE analysis. Finally, the parametric analysis was used to quantitatively investigate the effect of the parameters of the adhesive layer and host material on the strain transfer rate and average strain transfer rate.

Delay time and Hartman effect in strain engineered graphene

International Nuclear Information System (INIS)

Chen, Xi; Deng, Zhi-Yong; Ban, Yue

2014-01-01

Tunneling times, including group delay and dwell time, are studied for massless Dirac electrons transmitting through a one-dimensional barrier in strain-engineered graphene. The Hartman effect, the independence of group delay on barrier length, is induced by the strain effect, and associated with the transmission gap and the evanescent mode. The influence of barrier height/length and strain modulus/direction on the group delay is also discussed, which provides the flexibility to control the group delay with applications in graphene-based devices. The relationship between group delay and dwell time is finally derived to clarify the nature of the Hartman effect

Acute Heat Stress Changes Protein Expression in the Testes of a Broiler-Type Strain of Taiwan Country Chickens.

Science.gov (United States)

Wang, Shih-Han; Cheng, Chuen-Yu; Chen, Chao-Jung; Chan, Hong-Lin; Chen, Hsin-Hsin; Tang, Pin-Chi; Chen, Chih-Feng; Lee, Yen-Pai; Huang, San-Yuan

2018-03-19

Heat stress leads to decreased fertility in roosters. This study investigated the global protein expression in response to acute heat stress in the testes of a broiler-type strain of Taiwan country chickens (TCCs). Twelve 45-week-old roosters were randomly allocated to the control group maintained at 25°C, and three groups subjected to acute heat stress at 38°C for 4 h, with 0, 2, and 6 h of recovery, respectively. Testis samples were collected for hematoxylin and eosin staining, apoptosis assay, and protein analysis. The results revealed 101 protein spots that differed significantly from the control following exposure to acute heat stress. The proteins that were differentially expressed participated mainly in protein metabolism and other metabolic processes, responses to stimuli, apoptosis, cellular organization, and spermatogenesis. Proteins that negatively regulate apoptosis were downregulated and proteins involved in autophagy and major heat shock proteins (HSP90α, HSPA5, and HSPA8) were upregulated in the testes of heat-stressed chickens. In conclusion, acute heat stress causes a change in protein expression in the testes of broiler-type B strain TCCs and may thus impair cell morphology, spermatogenesis, and apoptosis. The expression of heat shock proteins increased to attenuate the testicular injury induced by acute heat stress.

Methods for predicting isochronous stress-strain curves

International Nuclear Information System (INIS)

Kiyoshige, Masanori; Shimizu, Shigeki; Satoh, Keisuke.

1976-01-01

Isochronous stress-strain curves show the relation between stress and total strain at a certain temperature with time as a parameter, and they are drawn up from the creep test results at various stress levels at a definite temperature. The concept regarding the isochronous stress-strain curves was proposed by McVetty in 1930s, and has been used for the design of aero-engines. Recently the high temperature characteristics of materials are shown as the isochronous stress-strain curves in the design guide for the nuclear energy equipments and structures used in high temperature creep region. It is prescribed that these curves are used as the criteria for determining design stress intensity or the data for analyzing the superposed effects of creep and fatigue. In case of the isochronous stress-strain curves used for the design of nuclear energy equipments with very long service life, it is impractical to determine the curves directly from the results of long time creep test, accordingly the method of predicting long time stress-strain curves from short time creep test results must be established. The method proposed by the authors, for which the creep constitution equations taking the first and second creep stages into account are used, and the method using Larson-Miller parameter were studied, and it was found that both methods were reliable for the prediction. (Kako, I.)

Species attribution and strain typing of Oenococcus oeni (formerly Leuconostoc oenos) with restriction endonuclease fingerprints.

Science.gov (United States)

Viti, C; Giovannetti, L; Granchi, L; Ventura, S

1996-10-01

In several wines, malolactic fermentation is required to improve the organoleptic characters and to stabilize the final product. In order to establish a controlled malolactic fermentation in wine, easy identification and sensitive typing of strains of Oenococcus oeni (new name of the malolactic bacterium Leuconostoc oenos) used as starter cultures are necessary. To accomplish these tasks, several strains of Oenococcus oeni isolated from wines of the Chianti region (Italy), along with reference strains and strains of L. mesenteroides subsp. mesenteroides, L. carnosum, L. fallax, L. pseudomesenteroides, L. lactis and Weisella paramesenteroides, were studied with RFLP of ribosomal genes and ultrasensitive total DNA restriction pattern analysis performed on polyacrylamide gel. With each of four restriction endonucleases used, identical restriction profiles of ribosomal genes were obtained for all strains of O. oeni. These ribopatterns, being strongly dissimilar to profiles of the other lactic acid bacteria tested, appear to be well suited for the attribution of wine lactic acid bacteria to the species O. oeni. Cluster analysis performed on two total DNA restriction profile data sets showed that the species O. oeni possesses a good degree of genomic homogeneity. Very sensitive typing of strains of O. oeni was obtained with total DNA restriction profiles. The potential of an integrated approach using restriction profiles for species assignment and typing of selected malolactic bacteria is demonstrated.

Effects of mean strain on the random cyclic stress-strain relations of 0Cr18Ni10Ti pipe steel

International Nuclear Information System (INIS)

Zhao Yongxiang; Yang Bing

2005-01-01

Experimental study is performed for the effects of the mean strain on the random cyclic stress-strain relations of the new nuclear material, 0Cr18Ni10Ti pipe steel. From saving the size of specimens, an improved maximum likelihood fatigue test method is proposed to operate the present strain-controlled fatigue tests. Six straining ratios, -1, -0.52, -0.22, 0.029, 0.18, and 0.48, respectively, are applied to study the effects. Fatigue test has been carried out on totally 104 specimens. The test results reveal that the material exhibits a Masing behaviour and the saturation hysteresis loops under the six ratios hold an entirely relaxation effect of mean stress. There is no effectively method for the description of the mean straining effects under this case. Previous Zhao's random stress-strain relations are therefore applied to characterizing effectively the scattering test data under the six ratios on a basis of Ramberg-Osgood equation. Then the effects of the ratios are analyzed respectively on the average stress amplitudes, the standard deviations of the stress amplitudes, and the stress amplitudes under different survival probabilities and confidences. The results reveal that the ratios act a relatively decreasing effect to the stress amplitudes under higher survival probabilities and confidences. The strongest effect appears at the ratio of 0.029, and a weaker effect acts as the distance increase of the ratio from the zero. In addition, it is indicated that the effects from the sense of average fatigue lives might result in a wrong conclusion. The effects can be appropriately assessed from a probabilistic sense to take into account the scattering regularity of test data and the size of sampling. (author)

A Mutated Yeast Strain with Enhanced Ethanol Production Efficiency and Stress Tolerance

Directory of Open Access Journals (Sweden)

Naghmeh Hemmati1*, David A. Lightfoot1,2, and Ahmed Fakhoury3

2012-05-01

Full Text Available One of the strategies to improve and optimize bio-ethanolproduction from new feed stocks is to develop new strainsof Saccharomyces cerevisiae with tolerance to stresses. Themain objectives here were to; generate S. cerevisiae mutantstolerant to high ethanol concentrations; test for their abilityto ferment maize starch; and partially characterize the mutationsresponsible for the new phenotypes. A combinationof mutagenesis, selection and cross-stress protection methodswere used. EMS (ethyl methanesulfonate was used tomutagenize one S. cerevisiae strain. The mutagenized yeaststrain was exposed to high concentrations of ethanol andtolerant mutants were isolated. Mutants showed improvedethanol yield (0.02-0.03 g/g of maize and fermentation efficiency(3-5%. Finally, AFLP (Amplified Fragment LengthPolymorphism was performed to identify polymorphisms inthe mutants that might underlie the strains ethanol tolerance.The best performing mutant isolate had four altered genetranscripts encoding; an arginine uptake and canavanine resistanceprotein (CAN1; mitochondrial membrane proteins(SLS1; a putative membrane glycoprotein (VTH1; and cytochromeC oxidase (COX6; EC 1.9.3.1 among about 1,000tested. It was concluded these mutations might underlie theimproved ethanol production efficiency and stress tolerance.

Investigation of Antibiotic Susceptibility Pattern of Staphylococcus aureus Strains Isolated from Patients Referring to Some Treatment Centers of Qom City, Iran

Directory of Open Access Journals (Sweden)

Sara Mosaei

2017-07-01

Full Text Available Background and Objectives: Staphylococcus aureus is one of the important causes of nosocomial infections. Resistance to various antibiotics, such as beta-lactams, aminoglycosides, and macrolides is one of the major problems in treatment and prevention of infections caused by this bacterium. Therefore, accurate determination of antibiotic susceptibility pattern of organisms isolated from patients can be beneficial in treatment and prevention of dangerous infections. The objective of this study was to isolate S. aureus bacterium and to determine the antibiotic susceptibility pattern of the isolated strains in patients referred to some treatment centers of Qom city. Methods: In this descriptive cross-sectional study, 340 clinical samples, were collected from September 2016 to July 2017. After isolation and primary identification of S. aureus isolates (using standard bacteriology methods, the isolated strains were confirmed by PCR technique and amplification of femA gene as a molecular diagnostic marker of S. aureus. Finally, antibiotic susceptibility pattern of the strains, was determined by disk diffusion method according to CLSI guideline. Results: Out of 340 clinical samples, 86 S. aureus strains were isolated and identified based on phenotypic characteristics. The femA gene was observed only in 45 strains (52.32% based on molecular analysis. The results of the antibiotic susceptibility test showed that the highest resistance was to penicillin (86.04% and the lowest resistance was to chloramphenicol (0%. Conclusion: The results of this study indicated that femA gene cannot by itself identify all the S. aureus strains. Also, with regard to the results of antibiogram test, it seems that antibiotic susceptibility test is necessary for S. aureus strains isolated from patients.

Unsteady Aerodynamic Force Sensing from Measured Strain

Science.gov (United States)

Pak, Chan-Gi

2016-01-01

A simple approach for computing unsteady aerodynamic forces from simulated measured strain data is proposed in this study. First, the deflection and slope of the structure are computed from the unsteady strain using the two-step approach. Velocities and accelerations of the structure are computed using the autoregressive moving average model, on-line parameter estimator, low-pass filter, and a least-squares curve fitting method together with analytical derivatives with respect to time. Finally, aerodynamic forces over the wing are computed using modal aerodynamic influence coefficient matrices, a rational function approximation, and a time-marching algorithm. A cantilevered rectangular wing built and tested at the NASA Langley Research Center (Hampton, Virginia, USA) in 1959 is used to validate the simple approach. Unsteady aerodynamic forces as well as wing deflections, velocities, accelerations, and strains are computed using the CFL3D computational fluid dynamics (CFD) code and an MSC/NASTRAN code (MSC Software Corporation, Newport Beach, California, USA), and these CFL3D-based results are assumed as measured quantities. Based on the measured strains, wing deflections, velocities, accelerations, and aerodynamic forces are computed using the proposed approach. These computed deflections, velocities, accelerations, and unsteady aerodynamic forces are compared with the CFL3D/NASTRAN-based results. In general, computed aerodynamic forces based on the lifting surface theory in subsonic speeds are in good agreement with the target aerodynamic forces generated using CFL3D code with the Euler equation. Excellent aeroelastic responses are obtained even with unsteady strain data under the signal to noise ratio of -9.8dB. The deflections, velocities, and accelerations at each sensor location are independent of structural and aerodynamic models. Therefore, the distributed strain data together with the current proposed approaches can be used as distributed deflection

Strain localization during tensile Hopkinson bar testing of commercially pure titanium and Ti6Al4V titanium alloy

Directory of Open Access Journals (Sweden)

Moćko Wojciech

2015-01-01

Full Text Available The goal of the analysis was to determine the strain localization for various specimen shapes (type A and type B according to PN-EN ISO 26203-1 standard and different loading conditions, i.e. quasi- static and dynamic. Commercially pure titanium (Grade 2 and titanium alloy Ti6Al4V (Grade 5 were selected for the tests. Tensile loadings were applied out using servo-hydraulic testing machine and tensile Hopkinson bar with pre-tension. The results were recorded using ARAMIS system cameras and fast camera Phantom V1210, respectively at quasi-static and dynamic loading conditions. Further, specimens outline was determined on the basis of video data using TEMA MOTION software. The strain distribution on the specimen surface was estimated using digital image correlation method. The larger radius present in the specimen of type B in comparison to specimen of type A, results in slight increase of the elongation for commercially pure titanium at both quasi-static and dynamic loading conditions. However this effect disappears for Ti6Al4V alloy. The increase of the elongation corresponds to the stronger necking effect. Material softening due to increase of temperature induced by plastic work was observed at dynamic loading conditions. Moreover lower elongation at fracture point was found at high strain rates for both materials.

Low Cycle Fatigue of Steel in Strain Controled Cyclic Bending

Directory of Open Access Journals (Sweden)

Kulesa Anna

2016-03-01

Full Text Available The paper presents a comparison of the fatigue life curves based on test of 15Mo3 steel under cyclic, pendulum bending and tension-compression. These studies were analyzed in terms of a large and small number of cycles where strain amplitude is dependent on the fatigue life. It has been shown that commonly used Manson-Coffin-Basquin model cannot be used for tests under cyclic bending due to the impossibility of separating elastic and plastic strains. For this purpose, some well-known models of Langer and Kandil and one new model of authors, where strain amplitude is dependent on the number of cycles, were proposed. Comparing the results of bending with tension-compression it was shown that for smaller strain amplitudes the fatigue life for both test methods were similar, for higher strain amplitudes fatigue life for bending tests was greater than for tension-compression.

Final test results for the ground operations demonstration unit for liquid hydrogen

Science.gov (United States)

Notardonato, W. U.; Swanger, A. M.; Fesmire, J. E.; Jumper, K. M.; Johnson, W. L.; Tomsik, T. M.

2017-12-01

Described herein is a comprehensive project-a large-scale test of an integrated refrigeration and storage system called the Ground Operations and Demonstration Unit for Liquid Hydrogen (GODU LH2), sponsored by the Advanced Exploration Systems Program and constructed at Kennedy Space Center. A commercial cryogenic refrigerator interfaced with a 125,000 l liquid hydrogen tank and auxiliary systems in a manner that enabled control of the propellant state by extracting heat via a closed loop Brayton cycle refrigerator coupled to a novel internal heat exchanger. Three primary objectives were demonstrating zero-loss storage and transfer, gaseous liquefaction, and propellant densification. Testing was performed at three different liquid hydrogen fill-levels. Data were collected on tank pressure, internal tank temperature profiles, mass flow in and out of the system, and refrigeration system performance. All test objectives were successfully achieved during approximately two years of testing. A summary of the final results is presented in this paper.

SINGLE HEATER TEST FINAL REPORT

International Nuclear Information System (INIS)

J.B. Cho

1999-01-01

The Single Heater Test is the first of the in-situ thermal tests conducted by the U.S. Department of Energy as part of its program of characterizing Yucca Mountain in Nevada as the potential site for a proposed deep geologic repository for the disposal of spent nuclear fuel and high-level nuclear waste. The Site Characterization Plan (DOE 1988) contained an extensive plan of in-situ thermal tests aimed at understanding specific aspects of the response of the local rock-mass around the potential repository to the heat from the radioactive decay of the emplaced waste. With the refocusing of the Site Characterization Plan by the ''Civilian Radioactive Waste Management Program Plan'' (DOE 1994), a consolidated thermal testing program emerged by 1995 as documented in the reports ''In-Situ Thermal Testing Program Strategy'' (DOE 1995) and ''Updated In-Situ Thermal Testing Program Strategy'' (CRWMS M and O 1997a). The concept of the Single Heater Test took shape in the summer of 1995 and detailed planning and design of the test started with the beginning fiscal year 1996. The overall objective of the Single Heater Test was to gain an understanding of the coupled thermal, mechanical, hydrological, and chemical processes that are anticipated to occur in the local rock-mass in the potential repository as a result of heat from radioactive decay of the emplaced waste. This included making a priori predictions of the test results using existing models and subsequently refining or modifying the models, on the basis of comparative and interpretive analyses of the measurements and predictions. A second, no less important, objective was to try out, in a full-scale field setting, the various instruments and equipment to be employed in the future on a much larger, more complex, thermal test of longer duration, such as the Drift Scale Test. This ''shake down'' or trial aspect of the Single Heater Test applied not just to the hardware, but also to the teamwork and cooperation between

High Strain Rate Deformation Mechanisms of Body Centered Cubic Material Subjected to Impact Loading

Science.gov (United States)

Visser, William

utilized to simulate the shock loading and twin evolution for these loading conditions. The second part of this research ties into the modeling efforts. Within the model for predicting twin volume fraction is a twin growth equation and a constant describing the stress at which the twin nucleation will occur. By using a constant value for the twin nucleation stress modeling efforts fail to accurately predict the growth and final twin volume fraction. A second shock loading experimental study combined with high strain rate compression tests using a split Hopkinson pressure bar were completed to determine a twin nucleation stress equation as a function of dislocation density. Steel specimens were subjected to cold rolling to 3% strain and subsequently impacted using the gas gun at different pressures. The increase in dislocation density due to pre-straining substantially increased the twin nucleation stress indicating that twin nucleation stress in dependent upon prior strain history. This has been explained in terms of the velocity and generation rates of both perfect and partial dislocations. An explicit form of the critical twin nucleation stress was developed and parameters were determined through plate impact tests and low temperature (77K) SHPB compression tests. The final component in studying deformation twin mechanisms in BCC steel extends the research to the post-impact mechanical properties and how the twin volume fraction affects the dynamic flow stress. Compression tests between 293K and 923K at an average strain rate of 4700 s-1 were completed on the as-received and 3% pre-strained steels in both the initial condition and after being impacted at pressures of 6GPa and 11GPa. Results of the experimental testing were used in a thermal activation model in order to distinguish separate components in the microstructure contributing to the enhanced flow stress caused by the shock loading. It has been shown that the dislocations generated from shock loading are

Production of lipids in 10 strains of Chlorella and Parachlorella, and enhanced lipid productivity in Chlorella vulgaris

Energy Technology Data Exchange (ETDEWEB)

Pribyl, Pavel; Cepak, Vladislav [Academy of Sciences of the Czech Republic, Trebon (Czech Republic). Algological Centre and Centre for Bioindication and Revitalization; Zachleder, Vilem [Academy of Sciences of the Czech Republic, Trebon (Czech Republic). Lab. of the Cell Cycles of Algae

2012-04-15

We tested 10 different Chlorella and Parachlorella strains under lipid induction growth conditions in autotrophic laboratory cultures. Between tested strains, substantial differences in both biomass and lipid productivity as well as in the final content of lipids were found. The most productive strain (Chlorella vulgaris CCALA 256) was subsequently studied in detail. The availability of nitrates and/or phosphates strongly influenced growth and accumulation of lipids in cells by affecting cell division. Nutrient limitation substantially enhanced lipid productivity up to a maximal value of 1.5 g l{sup -1} day{sup -1}. We also demonstrated the production of lipids through large-scale cultivation of C. vulgaris in a thin layer photobioreactor, even under suboptimal conditions. After 8 days of cultivation, maximal lipid productivity was 0.33 g l{sup -1} day{sup -1}, biomass density was 5.7 g l{sup -1} dry weight and total lipid content was more than 30% dry weight. C. vulgaris lipids comprise fatty acids with a relatively high degree of saturation compared with canola oil offering a possible alternative to the use of higher plant oils. (orig.)

OSM-Classic : An optical imaging technique for accurately determining strain

Science.gov (United States)

Aldrich, Daniel R.; Ayranci, Cagri; Nobes, David S.

OSM-Classic is a program designed in MATLAB® to provide a method of accurately determining strain in a test sample using an optical imaging technique. Measuring strain for the mechanical characterization of materials is most commonly performed with extensometers, LVDT (linear variable differential transistors), and strain gauges; however, these strain measurement methods suffer from their fragile nature and it is not particularly easy to attach these devices to the material for testing. To alleviate these potential problems, an optical approach that does not require contact with the specimen can be implemented to measure the strain. OSM-Classic is a software that interrogates a series of images to determine elongation in a test sample and hence, strain of the specimen. It was designed to provide a graphical user interface that includes image processing with a dynamic region of interest. Additionally, the stain is calculated directly while providing active feedback during the processing.

The role of creep in stress strain curves for copper

International Nuclear Information System (INIS)

Sandström, Rolf; Hallgren, Josefin

2012-01-01

Highlights: ► A dislocation based model takes into account both dynamic and static recovery. ► Tests at constant load and at constant strain rate modelled without fitting parameters. ► The model can describe primary and secondary creep of Cu-OFP from 75 to 250 °C. ► The temperature and strain rate dependence of stress strain curves can be modelled. ► Intended for the slow strain rates in canisters for storage of nuclear waste. - Abstract: A model for plastic deformation in pure copper taking work hardening, dynamic recovery and static recovery into account, has been formulated using basic dislocation mechanisms. The model is intended to be used in finite-element computations of the long term behaviour of structures in Cu-OFP for storage of nuclear waste. The relation between the strain rate and the maximum flow stress in the model has been demonstrated to correspond to strain rate versus stress in creep tests for oxygen free copper alloyed with phosphorus Cu-OFP. A further development of the model can also represent the primary and secondary stage of creep curves. The model is compared to stress strain curves in compression and tension for Cu-OFP. The compression tests were performed at room temperature for strain rates between 5 × 10 −5 and 5 × 10 −3 s −1 . The tests in tension covered the temperature range 20–175 °C for strain rates between 1 × 10 −7 and 1 × 10 −4 s −1 . Consequently, it is demonstrated that the model can represent mechanical test data that have been generated both at constant load and at constant strain rate without the use of any fitting parameters.

Validation of the Abbreviated Brucella AMOS PCR as a Rapid Screening Method for Differentiation of Brucella abortus Field Strain Isolates and the Vaccine Strains, 19 and RB51

OpenAIRE

Ewalt, Darla R.; Bricker, Betsy J.

2000-01-01

The Brucella AMOS PCR assay was previously developed to identify and differentiate specific Brucella species. In this study, an abbreviated Brucella AMOS PCR test was evaluated to determine its accuracy in differentiating Brucella abortus into three categories: field strains, vaccine strain 19 (S19), and vaccine strain RB51/parent strain 2308 (S2308). Two hundred thirty-one isolates were identified and tested by the conventional biochemical tests and Brucella AMOS PCR. This included 120 isola...

Effect of various Portland cement paste compositions on early-age strain

Science.gov (United States)

Guzzetta, Alana G.

Early-age strain in paste, mortar, and concrete mixtures was investigated using a new method where the specimen shape was a cone frustum. Strain of the specimen from both the horizontal and vertical directions was captured by height change measurement. The volumetric strain was then calculated as a function of the height change and was plotted versus time. A correlation was found between the slopes of the volumetric strain curve resulting from this test method and the initial setting time of the tested material. An initial evaluation of the repeatability of this innovative test method was conducted. The early-age strain effects of aggregate volume, shrinkage reducing admixture, water-cementitious ratio (w/cm), and partial cement replacement with supplementary cementitious materials were tested and individually compared. From these comparisons, it was observed that ambient temperature, bleed water development, and rheological properties had a significant impact on the volumetric strain results. Data showed increased strain as aggregate volume was reduced and as the w/cm was changed from 0.25 up to 0.50. The addition of shrinkage reducing admixture generally caused an increase in the 36-hour volumetric strain value. In most of the mixtures, cement replacement with 20% fly ash or 10% metakaolin reduced the measured volumetric strain when the w/cm was 0.30. Replacement of cement with 10% silica fume caused an insignificant change in volumetric strain results.

Effect of ratchet strain on fatigue and creep–fatigue strength of Mod.9Cr–1Mo steel

International Nuclear Information System (INIS)

Ando, Masanori; Isobe, Nobuhiro; Kikuchi, Koichi; Enuma, Yasuhiro

2012-01-01

Highlights: ► Uniaxial fatigue and creep–fatigue tests with superimposed strain were performed. ► Variety of superimposed strain were applied as ratchet strain in the tests. ► Effect of superimposed strain on fatigue and creep–fatigue life is negligible. ► A cyclic softening character reducing the effect of superimposed strain. - Abstract: The effect of ratcheting deformation on fatigue and creep–fatigue life in Mod.9Cr–1Mo steel was investigated. Uniaxial fatigue and creep–fatigue testing with superimposed strain were performed to evaluate the effect of ratcheting deformation on the failure cycle. In a series of tests, a specific amount of superimposed strain was accumulated in each cycle. The accumulated strain as ratcheting deformation, cycles to reach the accumulated strain, and test temperatures were varied in the tests. In the fatigue tests with superimposed strain at 550 °C, slight reductions of failure lives were observed. All of the numbers of cycles to failure in the fatigue tests with superimposed strain were within a factor of 1.5 of that of the fatigue test without superimposed strain at 550 °C. The apparent relationship between failure cycles and testing parameters was not observed. In fatigue tests with superimposed strain at 550 °C, maximum mean stress was insignificant and generated in early cycles because Mod.9Cr–1Mo steel exhibits cyclic softening characteristics. It was assumed that suppression of mean stress generation by cyclic softening reduces the effect of ratcheting strain. Conversely, failure lives were increased by accumulated strain in the test conducted at 450 °C because of stress–strain hysteresis loop shrinkage caused by cyclic softening induced by the accumulated strain. In the creep–fatigue tests with superimposed strain, test results indicated that the accumulated stain was negligible. It was concluded that the effect of ratcheting deformation on fatigue and creep–fatigue life is negligible as long

A method for determining the critical strain for recrystallisation in metals

International Nuclear Information System (INIS)

Morais, G.A. de; Pagnano, C.A.G.; Gouvea, J.A.

1975-01-01

A rapid method of determining the critical strain for recrystallisation is metals is described, the results having been verified in the case of rolled pure titanium sheet. Using experimentally checked hypotheses, the plastic strain in a tensile test piece of varying cross-section could be calculated. After straining, the test piece was annealed isothermically at various temperatures, thus showing the variation of grain size with strain [pt

A procedure to generate input data of cyclic softening and hardening for FEM analysis from constant strain amplitude fatigue tests in LCF regime

International Nuclear Information System (INIS)

Sarajaervi, U.; Cronvall, O.

2007-03-01

Fatigue is produced by cyclic application of stresses by mechanical or thermal loading. The metal subjected to fluctuating stress will fail at stresses much lower than those required to cause fracture in a single application of load. The key parameters are the range of stress variation and the number of its occurrences. Low-cycle fatigue, usually induced by mechanical and thermal loads, is distinguished from high-cycle fatigue, mainly associated with vibration or high number of small thermal fluctuations. Numerical models describing fatigue behaviour of austenitic stainless piping steels under cyclic loading and their applicability for modelling of low-cycle-fatigue are discussed in this report. In order to describe the cyclic behaviour of the material for analysis with finite element method (FEM) based analysis code ABAQUS, the test data, i.e. stress-strain curves, have to be processed. A code to process the data all through the test duration was developed within this study. A description of this code is given also in this report. Input data for ABAQUS was obtained to describe both kinematic and isotropic hardening properties. Further, by combining the result data for various strain amplitudes a mathematic expression was be created which allows defining a parameter surface for cyclic (i.e. isotropic) hardening. Input data for any strain amplitude within the range of minimum and maximum strain amplitudes of the test data can be assessed with the help of the developed 3D stress-strain surface presentation. The modelling of the fatigue induced initiation and growth of cracks was not considered in this study. On the other hand, a considerable part of the fatigue life of nuclear power plant (NPP) piping components is spent in the phase preceding the initiation and growth of cracks. (au)

A procedure to generate input data of cyclic softening and hardening for FEM analysis from constant strain amplitude fatigue tests in LCF regime

Energy Technology Data Exchange (ETDEWEB)

Sarajaervi, U.; Cronvall, O. [VTT (Finland)

2007-03-15

Fatigue is produced by cyclic application of stresses by mechanical or thermal loading. The metal subjected to fluctuating stress will fail at stresses much lower than those required to cause fracture in a single application of load. The key parameters are the range of stress variation and the number of its occurrences. Low-cycle fatigue, usually induced by mechanical and thermal loads, is distinguished from high-cycle fatigue, mainly associated with vibration or high number of small thermal fluctuations. Numerical models describing fatigue behaviour of austenitic stainless piping steels under cyclic loading and their applicability for modelling of low-cycle-fatigue are discussed in this report. In order to describe the cyclic behaviour of the material for analysis with finite element method (FEM) based analysis code ABAQUS, the test data, i.e. stress-strain curves, have to be processed. A code to process the data all through the test duration was developed within this study. A description of this code is given also in this report. Input data for ABAQUS was obtained to describe both kinematic and isotropic hardening properties. Further, by combining the result data for various strain amplitudes a mathematic expression was be created which allows defining a parameter surface for cyclic (i.e. isotropic) hardening. Input data for any strain amplitude within the range of minimum and maximum strain amplitudes of the test data can be assessed with the help of the developed 3D stress-strain surface presentation. The modelling of the fatigue induced initiation and growth of cracks was not considered in this study. On the other hand, a considerable part of the fatigue life of nuclear power plant (NPP) piping components is spent in the phase preceding the initiation and growth of cracks. (au)

Effect of test temperature and strain rate on the tensile properties of high-strength, high-conductivity copper alloys

Energy Technology Data Exchange (ETDEWEB)

Zinkle, S.J.; Eatherly, W.S. [Oak Ridge National Lab., TN (United States)

1997-04-01

The unirradiated tensile properties of wrought GlidCop AL25 (ITER grade zero, IGO) solutionized and aged CuCrZr, and cold-worked and aged and solutionized and aged Hycon 3HP{trademark} CuNiBe have been measured over the temperature range of 20-500{degrees}C at strain rates between 4 x 10{sup {minus}4} s{sup {minus}1} and 0.06 s{sup {minus}1}. The measured room temperature electrical conductivity ranged from 64 to 90% IACS for the different alloys. All of the alloys were relatively insensitive to strain rate at room temperature, but the strain rate sensitivity of GlidCop Al25 increased significantly with increasing temperature. The CuNiBe alloys exhibited the best combination of high strength and high conductivity at room temperature. The strength of CuNiBe decreased slowly with increasing temperature. However, the ductility of CuNiBe decreased rapidly with increasing temperature due to localized deformation near grain boundaries, making these alloy heats unsuitable for typical structural applications above 300{degrees}C. The strength and uniform elongation of GlidCop Al25 decreased significantly with increasing temperature at a strain rate of 1 x 10{sup {minus}3} s{sup {minus}1}, whereas the total elongation was independent of test temperature. The strength and ductility of CuCrZr decreased slowly with increasing temperature.

Creep of OFHC and silver copper at simulated final repository canister-service conditions

International Nuclear Information System (INIS)

Auerkari, P.; Leinonen, H.; Sandlin, S.

1991-07-01

Result of high-resolution creep rate measurements are described for estimating very long term creep life of copper and silver alloyed copper at room temperature and at stresses approaching the expected service conditions of final repository canisters. The aim was to assess the limiting service stress levels for potential canister wall materials. The 0.1 % silver alloyed copper showed minimum creep rates of 10 - 9 to 10 - 10 l/h, corresponding to 1 % strain in about 1000 to 10000 years, at room temperature and uniaxial stress level of 50 to 75 MPa. The predicted time to 1 % strain, when extrapolated from literature data, was at least one order of magnitude shorter. From the results of the present work, the 1 % creep life for OFHC copper was at most a few hundreds of years at 50 MPa stress level. The technique developed and used in this work for measuring very low strain rates appears useful for assessing low temperature creep life of practical structures essentially without accelerating the test from the service conditions

Creep of OFHC and silver copper at simulated final repository canister-service conditions

International Nuclear Information System (INIS)

Auerkari, P.; Leinonen, H.; Sandlin, S.

1991-09-01

Results of high-resolution creep rate measurements are described for estimating very long term creep life of copper and silver alloyed copper at room temperature and at stresses approaching the expected service conditions of final repository canisters. The aim was to assess the limiting service stress levels for potential canister wall materials. The 0.1% silver alloyed copper showed minimum creep rates of 10 -9 to 10 -10 l/h, corresponding to 1 % strain in about 1000 to 10000 years, at room temperature and uniaxial stress level of 50 to 75 MPa. The predicted time to 1 % strain, when extrapolated from literature data, was at least one order of magnitude shorter. From the results of the present work, the 1 % creep life for OFHC copper was at most a few hundreds of years at 50 MPa stress level. The technique developed and used in this work for measuring very low strain rates appears useful for assessing low temperature creep life of practical structures essentially without accelerating the test from the service conditions. (au)

Antimicrobial resistance of Helicobacter pylori strains to five antibiotics, including levofloxacin, in Northwestern Turkey

Directory of Open Access Journals (Sweden)

Reyhan Caliskan

2015-06-01

Full Text Available INTRODUCTION: Antibiotic resistance is the main factor that affects the efficacy of current therapeutic regimens against Helicobacter pylori. This study aimed to determine the rates of resistance to efficacy clarithromycin, amoxicillin, tetracycline, levofloxacin and metronidazole among H. pylori strains isolated from Turkish patients with dyspepsia. METHODS: H. pylori was cultured from corpus and antrum biopsies that were collected from patients with dyspeptic symptoms, and the antimicrobial susceptibility of H. pylori was determined using the E-test (clarithromycin, amoxicillin, tetracycline, metronidazole and levofloxacin according to the EUCAST breakpoints. Point mutations in the 23S rRNA gene of clarithromycin-resistant strains were investigated using real-time PCR. RESULTS: A total of 98 H. pylori strains were isolated, all of which were susceptible to amoxicillin and tetracycline. Of these strains, 36.7% (36/98 were resistant to clarithromycin, 35.5% (34/98 were resistant to metronidazole, and 29.5% (29/98 were resistant to levofloxacin. Multiple resistance was detected in 19.3% of the isolates. The A2143G and A2144G point mutations in the 23S rRNA-encoding gene were found in all 36 (100% of the clarithromycin-resistant strains. Additionally, the levofloxacin MIC values increased to 32 mg/L in our H. pylori strains. Finally, among the clarithromycin-resistant strains, 27.2% were resistant to levofloxacin, and 45.4% were resistant to metronidazole. CONCLUSIONS: We conclude that treatment failure after clarithromycin- or levofloxacin-based triple therapy is not surprising and that metronidazole is not a reliable agent for the eradication of H. pylori infection in Turkey.

The Evaluation of the Effect of Strain Limits on the Physical Properties of Magnetorheological Elastomers Subjected to Uniaxial and Biaxial Cyclic Testing.

OpenAIRE

Gorman, Dave; Murphy, Niall; Ekins, Ray; Jerrams, Stephen

2017-01-01

Magnetorheological Elastomers (MREs) are “smart” materials whose physical properties are altered by the application of magnetic fields. In a previous study by the authors [1], variations in the physical properties of MREs have been evaluated when subjected to a range of magnetic field strengths for both uniaxial and biaxial cyclic tests. By applying the same magnetic field to similar samples, this paper investigates the effect of both the upper strain limit and the strain amplitude on the pro...

SINGLE HEATER TEST FINAL REPORT

Energy Technology Data Exchange (ETDEWEB)

J.B. Cho

1999-05-01

The Single Heater Test is the first of the in-situ thermal tests conducted by the U.S. Department of Energy as part of its program of characterizing Yucca Mountain in Nevada as the potential site for a proposed deep geologic repository for the disposal of spent nuclear fuel and high-level nuclear waste. The Site Characterization Plan (DOE 1988) contained an extensive plan of in-situ thermal tests aimed at understanding specific aspects of the response of the local rock-mass around the potential repository to the heat from the radioactive decay of the emplaced waste. With the refocusing of the Site Characterization Plan by the ''Civilian Radioactive Waste Management Program Plan'' (DOE 1994), a consolidated thermal testing program emerged by 1995 as documented in the reports ''In-Situ Thermal Testing Program Strategy'' (DOE 1995) and ''Updated In-Situ Thermal Testing Program Strategy'' (CRWMS M&O 1997a). The concept of the Single Heater Test took shape in the summer of 1995 and detailed planning and design of the test started with the beginning fiscal year 1996. The overall objective of the Single Heater Test was to gain an understanding of the coupled thermal, mechanical, hydrological, and chemical processes that are anticipated to occur in the local rock-mass in the potential repository as a result of heat from radioactive decay of the emplaced waste. This included making a priori predictions of the test results using existing models and subsequently refining or modifying the models, on the basis of comparative and interpretive analyses of the measurements and predictions. A second, no less important, objective was to try out, in a full-scale field setting, the various instruments and equipment to be employed in the future on a much larger, more complex, thermal test of longer duration, such as the Drift Scale Test. This ''shake down'' or trial aspect of the Single Heater Test applied

Measurement of stress strain and vibrational properties of tendons

Science.gov (United States)

Revel, Gian Marco; Scalise, Alessandro; Scalise, Lorenzo

2003-08-01

The authors present a new non-intrusive experimental procedure based on laser techniques for the measurement of mechanical properties of tendons. The procedure is based on the measurement of the first resonance frequency of the tendon by laser Doppler vibrometry during in vitro tensile experiments, with the final aim of establishing a measurement procedure to perform the mechanical characterization of tendons by extracting parameters such as the resonance frequency, also achievable during in vivo investigation. The experimental procedure is reported, taking into account the need to simulate the physiological conditions of the Achilles tendon, and the measurement technique used for the non-invasive determination of tendon cross-sectional area during tensile vibration tests at different load levels is described. The test procedure is based on a tensile machine, which measures longitudinal tendons undergoing controlled load conditions. Cross-sectional area is measured using a new non-contact procedure for the measurement of tendon perimeter (repeatability of 99% and accuracy of 2%). For each loading condition, vibration resonance frequency and damping, cross-sectional area and tensile force are measured, allowing thus a mechanical characterization of the tendon. Tendon stress-strain curves are reported. Stress-strain curves have been correlated to the first vibration resonance frequency and damping of the tendon measured using a single-point laser Doppler vibrometer. Moreover, experimental results have been compared with a theoretical model of a vibrating cord showing discrepancies. In vitro tests are reported, demonstrating the validity of the method for the comparison of different aged rabbit tendons.

Molecular Typing of Acinetobacter Baumannii Clinical Strains in Tehran by Pulsed-Field Gel Electrophoresis

Directory of Open Access Journals (Sweden)

Neda Farahani

2013-03-01

Full Text Available Background & Objective : Currently, Acinetobacter baumannii is an important nosocomial pathogen insofar as its hospital outbreaks have been described from various geographical areas. Since the discrimination of strains within a species is important for delineating nosocomial outbreaks, this study was conducted with the aim of genotyping the A. baumannii clinical strains in Tehran via the pulsed-field gel electrophoresis (PFGE method, which is the most accurate method used for the typing of bacterial species.   Materials & methods: This study was performed on 70 isolates of acinetobacter baumannii isolated from patients from Baqiyatallah, Rasoole Akram, and Milad hospitals in Tehran. Cultural and biochemical methods were used for the identification of the isolates in species level, and then susceptibility tests were carried out on 50 isolates of A. baumannii using the disk diffusion method. The PFGE method was performed on the isolates by Apa I restriction enzyme. Finally, the results of the PFGE were analyzed. Result: Acinetobacter baumannii strains isolated from hospitals in Tehran showed seven different genetic patterns, two of which were sporadic . Also, genotypic profiles were different in each hospital, and different patterns of genetic resistance to common antibiotics were observed. Conclusion: A lthough diversity was observed among the strains of A. baumannii by the PFGE method in Tehran, no epidemic strains were found among them.  

Strain expansion-reduction approach

Science.gov (United States)

Baqersad, Javad; Bharadwaj, Kedar

2018-02-01

Validating numerical models are one of the main aspects of engineering design. However, correlating million degrees of freedom of numerical models to the few degrees of freedom of test models is challenging. Reduction/expansion approaches have been traditionally used to match these degrees of freedom. However, the conventional reduction/expansion approaches are only limited to displacement, velocity or acceleration data. While in many cases only strain data are accessible (e.g. when a structure is monitored using strain-gages), the conventional approaches are not capable of expanding strain data. To bridge this gap, the current paper outlines a reduction/expansion technique to reduce/expand strain data. In the proposed approach, strain mode shapes of a structure are extracted using the finite element method or the digital image correlation technique. The strain mode shapes are used to generate a transformation matrix that can expand the limited set of measurement data. The proposed approach can be used to correlate experimental and analytical strain data. Furthermore, the proposed technique can be used to expand real-time operating data for structural health monitoring (SHM). In order to verify the accuracy of the approach, the proposed technique was used to expand the limited set of real-time operating data in a numerical model of a cantilever beam subjected to various types of excitations. The proposed technique was also applied to expand real-time operating data measured using a few strain gages mounted to an aluminum beam. It was shown that the proposed approach can effectively expand the strain data at limited locations to accurately predict the strain at locations where no sensors were placed.

Hollow Cylinder Tests on Boom Clay: Modelling of Strain Localization in the Anisotropic Excavation Damaged Zone

Science.gov (United States)

François, Bertrand; Labiouse, Vincent; Dizier, Arnaud; Marinelli, Ferdinando; Charlier, Robert; Collin, Frédéric

2014-01-01

Boom Clay is extensively studied as a potential candidate to host underground nuclear waste disposal in Belgium. To guarantee the safety of such a disposal, the mechanical behaviour of the clay during gallery excavation must be properly predicted. In that purpose, a hollow cylinder experiment on Boom Clay has been designed to reproduce, in a small-scale test, the Excavation Damaged Zone (EDZ) as experienced during the excavation of a disposal gallery in the underground. In this article, the focus is made on the hydro-mechanical constitutive interpretation of the displacement (experimentally obtained by medium resolution X-ray tomography scanning). The coupled hydro-mechanical response of Boom Clay in this experiment is addressed through finite element computations with a constitutive model including strain hardening/softening, elastic and plastic cross-anisotropy and a regularization method for the modelling of strain localization processes. The obtained results evidence the directional dependency of the mechanical response of the clay. The softening behaviour induces transient strain localization processes, addressed through a hydro-mechanical second grade model. The shape of the obtained damaged zone is clearly affected by the anisotropy of the materials, evidencing an eye-shaped EDZ. The modelling results agree with experiments not only qualitatively (in terms of the shape of the induced damaged zone), but also quantitatively (for the obtained displacement in three particular radial directions).

Modulation of virulence and antibiotic susceptibility of enteropathogenic Escherichia coli strains by Enterococcus faecium probiotic strain culture fractions.

Science.gov (United States)

Ditu, Lia-Mara; Chifiriuc, Mariana Carmen; Bezirtzoglou, Eugenia; Voltsi, Chrysa; Bleotu, Coralia; Pelinescu, Diana; Mihaescu, Grigore; Lazar, Veronica

2011-12-01

The increasing rate of antimicrobial resistance drastically reduced the efficiency of conventional antibiotics and led to the reconsideration of the interspecies interactions in influencing bacterial virulence and response to therapy. The aim of the study was the investigation of the influence of the soluble and cellular fractions of Enterococcus (E.) faecium CMGB16 probiotic culture on the virulence and antibiotic resistance markers expression in clinical enteropathogenic Escherichia (E.) coli strains. The 7 clinical enteropathogenic E. coli strains, one standard E. coli ATCC 25,922 and one Bacillus (B.) cereus strains were cultivated in nutrient broth, aerobically at 37 °C, for 24 h. The E. faecium CMGB16 probiotic strain was cultivated in anaerobic conditions, at 37 °C in MRS (Man Rogosa Sharpe) broth, and co-cultivated with two pathogenic strains (B. cereus and E. coli O28) culture fractions (supernatant, washed sediment and heat-inactivated culture) for 6 h, at 37 °C. After co-cultivation, the soluble and cellular fractions of the probiotic strain cultivated in the presence of two pathogenic strains were separated by centrifugation (6000 rpm, 10 min), heat-inactivated (15 min, 100 °C) and co-cultivated with the clinical enteropathogenic E. coli strains in McConkey broth, for 24 h, at 37 °C, in order to investigate the influence of the probiotic fractions on the adherence capacity and antibiotic susceptibility. All tested probiotic combinations influenced the adherence pattern of E. coli tested strains. The enteropathogenic E. coli strains susceptibility to aminoglycosides, beta-lactams and quinolones was increased by all probiotic combinations and decreased for amoxicillin-clavulanic acid. This study demonstrates that the plurifactorial anti-infective action of probiotics is also due to the modulation of virulence factors and antibiotic susceptibility expression in E. coli pathogenic strains. Copyright © 2011 Elsevier Ltd. All rights reserved.

Two New Quadrilateral Elements Based on Strain States

Directory of Open Access Journals (Sweden)

Mohammad Rezaiee-Pajand

2015-06-01

Full Text Available In this paper, two new quadrilateral elements are formulated to solve plane problems. Low sensitivity to geometric distortion, no parasitic shear error, rotational invariance, and satisfying the Felippa pure bending test are characteristics of these suggested elements. One proposed element is formulated by establishing equilibrium equations for the second-order strain field. The other suggested element is obtained by establishing equilibrium equations only for the linear part of the strain field. The number of the strain states decreases when the conditions among strain states are satisfied. Several numerical tests are used to demonstrate the performance of the proposed elements. Famous elements, which were suggested by other researchers, are used as a means of comparison. It is shown that these novel elements pass the strong patch tests, even for extremely poor meshes, and one of them has an excellent accuracy and fast convergence in other complicated problems.

Probiotic Lactobacillus reuteri strains ATCC PTA 5289 and ATCC 55730 differ in their cariogenic properties in vitro.

Science.gov (United States)

Jalasvuori, Heli; Haukioja, Anna; Tenovuo, Jorma

2012-12-01

The effects of probiotics on cariogenic biofilms remain controversial. Our aim was to characterise two probiotic Lactobacillus reuteri strains, ATCC PTA 5289 and ATCC 55730 from a cariogenic standpoint in vitro. These strains are used in commercial products designed for oral health purposes. The adhesion and biofilm formation were studied on saliva-coated hydroxyapatite. The effects of glucose or sucrose on the biofilm formation were also tested. Arginine metabolism was assessed by measuring the pH in the presence of glucose and arginine. The degradation of hydroxyapatite was measured in three different growth media. Streptococcus mutans strains Ingbritt and MT 8148 were used as positive controls for bacterial adhesion and degradation of hydroxyapatite. Strain ATCC PTA 5289 adhered on saliva-coated hydroxyapatite and formed detectable biofilm, but strain ATCC 55730 was poor in both adhesion and biofilm formation. Both strains were arginolytic and raised the pH in the presence of arginine. The amount of dissolved calcium from hydroxyapatite correlated with bacterial growth rate and the final pH of the growth medium. L. reuteri strains ATCC PTA 5289 and ATCC 55730 differed in their adhesion, biofilm formation and arginine metabolism in vitro. Thus, these probiotic lactobacilli are likely to differ in their behaviour and cariogenic potential also in an oral environment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Curvature reduces bending strains in the quokka femur

Directory of Open Access Journals (Sweden)

Kyle McCabe

2017-03-01

Full Text Available This study explores how curvature in the quokka femur may help to reduce bending strain during locomotion. The quokka is a small wallaby, but the curvature of the femur and the muscles active during stance phase are similar to most quadrupedal mammals. Our hypothesis is that the action of hip extensor and ankle plantarflexor muscles during stance phase place cranial bending strains that act to reduce the caudal curvature of the femur. Knee extensors and biarticular muscles that span the femur longitudinally create caudal bending strains in the caudally curved (concave caudal side bone. These opposing strains can balance each other and result in less strain on the bone. We test this idea by comparing the performance of a normally curved finite element model of the quokka femur to a digitally straightened version of the same bone. The normally curved model is indeed less strained than the straightened version. To further examine the relationship between curvature and the strains in the femoral models, we also tested an extra-curved and a reverse-curved version with the same loads. There appears to be a linear relationship between the curvature and the strains experienced by the models. These results demonstrate that longitudinal curvature in bones may be a manipulable mechanism whereby bone can induce a strain gradient to oppose strains induced by habitual loading.

Design and test of the final ALICE SDD CARLOS end ladder board

CERN Document Server

Antinori, S; Falchieri, D; Gabrielli, A; Gandolfi, E; Masetti, M; Tosellob, F

2007-01-01

The paper presents the design and test of the final prototype of the CARLOS (Compression And Run Length Encoding Subsystem) end ladder board that is going to be used in the ALICE experiment at CERN. This board is able to compress data coming from one Silicon Drift Detector (SDD) front-end electronics and to send them towards the data concentrator card CARLOSrx in counting room via a 800 Mb/s optical link. The board design faces several constraints, mainly size (54x49 mm) and radiation tolerance: for this reason the board contains several CERN developed ASICs. A test setup has been realized for selecting the good devices among the 500 cards already produced.

Application of fiber optic grating strain sensor for measurement of strain under irradiation environment

International Nuclear Information System (INIS)

Kaji, Y.; Matsui, Y.; Kita, S.; Ide, H.; Tsukada, T.; Tsuji, H.

2001-01-01

In Japan Atomic Energy Research Institute (JAERI), in-pile strain measurement techniques have been developed using Japan Materials Testing Reactor (JMTR). In order to evaluate the performance of fiber optic grating sensor under irradiation environment, heat-up and performance tests at elevated temperature before irradiation and in-pile tests were performed in JMTR. (author)

A wide extent of inter-strain diversity in virulent and vaccine strains of alphaherpesviruses.

Directory of Open Access Journals (Sweden)

Moriah L Szpara

2011-10-01

Full Text Available Alphaherpesviruses are widespread in the human population, and include herpes simplex virus 1 (HSV-1 and 2, and varicella zoster virus (VZV. These viral pathogens cause epithelial lesions, and then infect the nervous system to cause lifelong latency, reactivation, and spread. A related veterinary herpesvirus, pseudorabies (PRV, causes similar disease in livestock that result in significant economic losses. Vaccines developed for VZV and PRV serve as useful models for the development of an HSV-1 vaccine. We present full genome sequence comparisons of the PRV vaccine strain Bartha, and two virulent PRV isolates, Kaplan and Becker. These genome sequences were determined by high-throughput sequencing and assembly, and present new insights into the attenuation of a mammalian alphaherpesvirus vaccine strain. We find many previously unknown coding differences between PRV Bartha and the virulent strains, including changes to the fusion proteins gH and gB, and over forty other viral proteins. Inter-strain variation in PRV protein sequences is much closer to levels previously observed for HSV-1 than for the highly stable VZV proteome. Almost 20% of the PRV genome contains tandem short sequence repeats (SSRs, a class of nucleic acids motifs whose length-variation has been associated with changes in DNA binding site efficiency, transcriptional regulation, and protein interactions. We find SSRs throughout the herpesvirus family, and provide the first global characterization of SSRs in viruses, both within and between strains. We find SSR length variation between different isolates of PRV and HSV-1, which may provide a new mechanism for phenotypic variation between strains. Finally, we detected a small number of polymorphic bases within each plaque-purified PRV strain, and we characterize the effect of passage and plaque-purification on these polymorphisms. These data add to growing evidence that even plaque-purified stocks of stable DNA viruses exhibit

Final safety and hazards analysis for the Battelle LOCA simulation tests in the NRU reactor

International Nuclear Information System (INIS)

Axford, D.J.; Martin, I.C.; McAuley, S.J.

1981-04-01

This is the final safety and hazards report for the proposed Battelle LOCA simulation tests in NRU. A brief description of equipment test design and operating procedure precedes a safety analysis and hazards review of the project. The hazards review addresses potential equipment failures as well as potential for a metal/water reaction and evaluates the consequences. The operation of the tests as proposed does not present an unacceptable risk to the NRU Reactor, CRNL personnel or members of the public. (author)

Occurrence of mannose resistant hemagglutinins in Escherichia coli strains isolated from porcine colibacillosis.

Science.gov (United States)

Truszczyński, M; Osek, J

1987-01-01

Three-hundred and fifty-eight E. coli strains isolated from piglets were tested for the presence of hemagglutinins by the use of the active hemagglutination test with or without mannose. Additionally 86 strains from the mentioned number of strains were investigated for the presence of common fimbriae using the same method but growing the strains in media especially suited for the development of this kind of fimbriae. These 358 strains and additionally 202 E. coli strains were tested using antisera for 987P and K88 antigens. It was found, using the active hemagglutination test, that 51.4% of the strains were hemagglutinating. The hemagglutinating strains carried the K88 antigen. All these strains were isolated from new-born and weaned piglets with enterotoxic form of colibacillosis, called also E. coli diarrhea. From cases of this form of colibacillosis originated also 26.7% of the strains in which common fimbriae (type 1) were detected. This result was obtained when the BHI medium was used for cultivation. In case of TSA medium only 2.3% of strains were positive. No specific or common fimbriae were found in strains recovered from septic form of colibacillosis and oedema disease (called also enterotoxaemic form of colibacillosis). No strain of 560 examined showed the presence of fimbrial 987P antigen.

Analysis of stress-strain behavior in Bi2223 composite tapes

International Nuclear Information System (INIS)

Sugano, M.; Osamura, K.; Nyilas, A.

2004-01-01

Tensile test was carried out for Bi2223/Ag/Ag alloy composite tapes at RT, 77 and 7 K. Two yielding points are observed in the stress-strain curves. From the stress-strain behavior of the components and critical current (I c ) as a function of tensile strain, it was found that the microscopic reason for these yieldings is attributed to yielding of Ag alloy and fracture of Bi2223, respectively. The strain at the second yielding has temperature dependence and it becomes larger with decreasing measured temperature. From the thermo-mechanical analysis, it can be explained by temperature dependence of compressive residual strain of Bi2223. Reversible recovery of I c was found during loading-unloading test. The relationship between the reversible strain limit and the intrinsic strain of Bi2223 was discussed

Susceptibilities of Mycoplasma bovis, Mycoplasma dispar, and Ureaplasma diversum strains to antimicrobial agents in vitro.

OpenAIRE

ter Laak, E A; Noordergraaf, J H; Verschure, M H

1993-01-01

The purpose of this study was to determine the susceptibility of various strains of Mycoplasma bovis, Mycoplasma dispar, and Ureaplasma diversum, which are prevalent causes of pneumonia in calves, to 16 antimicrobial agents in vitro. The MICs of the antimicrobial agents were determined by a serial broth dilution method for 16 field strains and the type strain of M. bovis, for 19 field strains and the type strain of M. dispar, and for 17 field strains of U. diversum. Final MICs for M. bovis an...

Use of abrupt strain path change for determining subsequent yield surface

DEFF Research Database (Denmark)

Kuwabara, T.; Kuroda, M.; Tvergaard, Viggo

2000-01-01

. In a biaxial tensile testing apparatus, a cruciform specimen is used, with the strains measured by a biaxial-strain gauge. Then, with the hydraulic pressure of two sets of opposing hydraulic cylinders servo-controlled independently, the testing apparatus can be used to prescribe an abrupt change of the strain...

Detection and quantification of creep strain using process compensated resonance testing (PCRT) sorting modules trained with modeled resonance spectra

Science.gov (United States)

Heffernan, Julieanne; Biedermann, Eric; Mayes, Alexander; Livings, Richard; Jauriqui, Leanne; Goodlet, Brent; Aldrin, John C.; Mazdiyasni, Siamack

2018-04-01

Process Compensated Resonant Testing (PCRT) is a full-body nondestructive testing (NDT) method that measures the resonance frequencies of a part and correlates them to the part's material and/or damage state. PCRT testing is used in the automotive, aerospace, and power generation industries via automated PASS/FAIL inspections to distinguish parts with nominal process variation from those with the defect(s) of interest. Traditional PCRT tests are created through the statistical analysis of populations of "good" and "bad" parts. However, gathering a statistically significant number of parts can be costly and time-consuming, and the availability of defective parts may be limited. This work uses virtual databases of good and bad parts to create two targeted PCRT inspections for single crystal (SX) nickel-based superalloy turbine blades. Using finite element (FE) models, populations were modeled to include variations in geometric dimensions, material properties, crystallographic orientation, and creep damage. Model results were verified by comparing the frequency variation in the modeled populations with the measured frequency variations of several physical blade populations. Additionally, creep modeling results were verified through the experimental evaluation of coupon geometries. A virtual database of resonance spectra was created from the model data. The virtual database was used to create PCRT inspections to detect crystallographic defects and creep strain. Quantification of creep strain values using the PCRT inspection results was also demonstrated.

Taxonomy of oxalotrophic Methylobacterium strains

Science.gov (United States)

Sahin, Nurettin; Kato, Yuko; Yilmaz, Ferah

2008-10-01

Most of the oxalotrophic bacteria are facultative methylotrophs and play important ecological roles in soil fertility and cycling of elements. This study gives a detailed picture of the taxonomy and diversity of these bacteria and provides new information about the taxonomical variability within the genus Methylobacterium. Twelve mesophilic, pink-pigmented, and facultatively methylotrophic oxalate-oxidizing strains were included in this work that had been previously isolated from the soil and some plant tissues by the potassium oxalate enrichment method. The isolates were characterized using biochemical tests, cellular lipid profiles, spectral characteristics of carotenoid pigments, G+C content of the DNA, and 16S rDNA sequencing. The taxonomic similarities among the strains were analyzed using the simple matching ( S SM) and Jaccard ( S J) coefficients, and the UPGMA clustering algorithm. The phylogenetic position of the strains was inferred by the neighbor-joining method on the basis of the 16S rDNA sequences. All isolates were Gram-negative, facultatively methylotrophic, oxidase and catalase positive, and required no growth factors. Based on the results of numerical taxonomy, the strains formed four closely related clusters sharing ≥85% similarity. Analysis of the 16S rDNA sequences demonstrated that oxalotrophic, pink-pigmented, and facultatively methylotrophic strains could be identified as members of the genus Methylobacterium. Except for M. variabile and M. aquaticum, all of the Methylobacterium type strains tested had the ability of oxalate utilization. Our results indicate that the capability of oxalate utilization seems to be an uncommon trait and could be used as a valuable taxonomic criterion for differentiation of Methylobacterium species.

Evaluation of the automated system Vitek2 for identification and antimicrobial susceptibility testing of Brazilian Gram-positive cocci strains

Directory of Open Access Journals (Sweden)

Pedro Alves d'Azevedo

Full Text Available Automated instruments offer many advantages for clinical laboratories. Nevertheless, they can have problems identifying and determining susceptibilities of some pathogens. Vitek® 2 (bioMérieux is an automated system that was recently introduced to Brazil. We evaluated the performance of this equipment for Brazilian isolates that had been characterized using reference identification and antimicrobial susceptibility testing methods. Ninety-nine strains of Gram-positive cocci from a local reference center collection were analyzed, consisting of 50 coagulasenegative Staphylococcus (CoNS and 49 Enterococcus and related species. Vitek® 2 correctly identified 79.8% (79/99 of the isolates. Oxacillin resistance was detected in 76% (19/25 of resistant S. epidermidis strains and in 88% (22/25 of other resistant CoNS species strains. Vancomycin resistance was detected in 100% (20/20 of resistant Enterococcus and related species strains. Vitek® 2 performed very well for the identification of S. epidermidis and non-epidermidis staphylococci, and for the detection of vancomycin resistance in Enterococcus and related species. However, the system needs improvement in order to provide reliable results for the characterization of some CoNS species, identification of Enterococcus and related species and for detecting oxacillin resistance in CoNS.

Effect of plastic strain on fracture strength of cracked components

International Nuclear Information System (INIS)

Kamaya, Masayuki

2009-01-01

Nuclear power plant components are occasionally subjected to large load by earthquake and may suffer plastic strain. Although the plastic strain induced in materials increases the strength, it may reduce the fracture toughness due to a crack in the components. In this study, the effect of the plastic strain on strength of cracked components was investigated. Firstly, the change in the tensile properties and fracture toughness due to plastic strain were examined for Type 316 stainless steel and carbon steel (SM490). The degree of nominal plastic strain was 5%, 10%, 20% and 40% (only for stainless steel). Secondly, the J-integral values of surface crack on a pipe were evaluated by finite element analyses. Finally, the critical load for fracture of the cracked pipe was evaluated for various pipe and crack geometries using the J-integral values and the fracture toughness obtained. It was concluded that the plastic strain enhances the fracture strength of the cracked components when the induced plastic strain is less than 10%, although the extremely large plastic strain could reduce the strength. (author)

Effect of plastic strain on fracture strength of cracked components

International Nuclear Information System (INIS)

Kamaya, Masayuki

2010-01-01

Nuclear power plant components are occasionally subjected to excessive load by earthquake and may suffer plastic strain. Although the plastic strain introduced in materials increases the strength, it may reduce the fracture toughness. In this study, the effect of the plastic strain on strength of cracked components was investigated. Firstly, the change in the tensile properties and fracture toughness due to plastic strain were examined for Type 316 stainless steel and carbon steel (SM 490). The degree of nominal plastic strain was 5%, 10%, 20% and 40% (only for stainless steel). Secondly, the J-integral values of surface crack on a pipe were evaluated by finite element analyses. Finally, the critical load for fracture of the cracked pipe was evaluated for various pipe and crack geometries using the J-integral values and the fracture toughness obtained. It was concluded that the plastic strain enhances the fracture strength of the cracked components when the induced plastic strain is less than 10%, although the extremely large plastic strain could reduce the strength. (author)

Atlas of stress-strain curves

CERN Document Server

2002-01-01

The Atlas of Stress-Strain Curves, Second Edition is substantially bigger in page dimensions, number of pages, and total number of curves than the previous edition. It contains over 1,400 curves, almost three times as many as in the 1987 edition. The curves are normalized in appearance to aid making comparisons among materials. All diagrams include metric (SI) units, and many also include U.S. customary units. All curves are captioned in a consistent format with valuable information including (as available) standard designation, the primary source of the curve, mechanical properties (including hardening exponent and strength coefficient), condition of sample, strain rate, test temperature, and alloy composition. Curve types include monotonic and cyclic stress-strain, isochronous stress-strain, and tangent modulus. Curves are logically arranged and indexed for fast retrieval of information. The book also includes an introduction that provides background information on methods of stress-strain determination, on...

Physico-chemical characterization and antibacterial activity of different types of honey tested on strains isolated from hospitalized patients

Directory of Open Access Journals (Sweden)

Junie Lia M.

2016-06-01

Full Text Available The first aim of the study was to compare the antibacterial activity of several types of honey of different origins, against some bacterial resistant strains. The strains had been isolated from patients. The second aim was to discover the correlations between the antibacterial character of honey and the physico-chemical properties of the honey. Ten honey samples (polyfloral, linden, acacia, manna, and sunflower from the centre of Romania were tested to determine their antibacterial properties against the following bacterial species: Pseudomonas aeruginosa, Escherichia coli, Staphylococcus aureus, Staphylococcus epidermidis, Salmonella enterica serovar Typhimurium, Bacillus cereus, Bacillus subtilis, and Listeria monocytogenes. Bacterial cultures in nutrient broth and the culture medium Mueller-Hinton agar were used. The susceptibility to antibiotics was performed using the disk diffusion method. All honey samples showed antibacterial activity on the isolated bacterial strains, in particular polyfloral (inhibition zone 13-21 mm in diameter - because it is the source of several plants, and manna (inhibition zone 13-19.5 mm in diameter, and sunflower (inhibition zone 14-18.5 mm in diameter. Pure honey has a significant antibacterial activity against some bacteria which are resistant to antibiotics. Bacterial strains differed in their sensitivity to honeys. Pseudomonas aeruginosa and Staphylococcus aureus were the most sensitive. The present study revealed that honey antibacterial activity depends on the origin of the honey. We also found that there was a significant correlation between antibacterial activity of honeys and the colour of the honey but not between acidity and pH. The statistical analysis showed that the honey type influences the antibacterial activity (diameter of the bacterial strains inhibition zones.

40 CFR 79.60 - Good laboratory practices (GLP) standards for inhalation exposure health effects testing.

Science.gov (United States)

2010-07-01

... infestation, odors, disease hazards, and environmental contamination. (v) Facilities shall have provisions to...) Where applicable, the number, body weight, sex, source of supply, species, strain, substrain, and age of... applicable, the final report shall include the number of animals or other test organisms used, sex, body...

Characterization of indigenous lactobacillus strains for probiotic properties.

Science.gov (United States)

Mojgani, Naheed; Hussaini, Fatimah; Vaseji, Narges

2015-02-01

Probiotics are defined as adequate amount of live microorganisms able to confer health benefits on the host. Currently, most commercially available probiotic products in the market belong to genera Lactobacillus. Traditional dairy products are usually rich source of Lactobacillus strains with significant health benefits. In order to evaluate the probiotic potential of these bacteria, it is essential to assess their health benefits, efficacy, and safety. The probiotic efficacy of two Lactobacillus strains namely Lactobacillus pentosus LP05 and L. brevis LB32 was evaluated. They were previously isolated from ewes' milk in a rural area in East Azerbaijan, Iran. The selected isolates were tested for certain phenotypic characters and identified to genus and species level by 16S rRNA gene sequencing and species specific primers. Further analysis included acid and bile resistance, antagonistic activity, cholesterol removing ability, survival in simulated gastric and upper intestine contents, aggregation and coaggregation properties. Finally, the adhering ability of the selected Lactobacillus strains to epithelial cells was tested using Caco-2 cell lines. The selected isolates tolerated bile salt concentrations ranging from 0.5% to 3%, however their coefficient of inhibition were varied. Both isolates hydrolyzed bile and grew at pH values of 3, 4, and 5, while isolate LP05 was not able to hydrolyze arginine. Based on 16s rRNA gene sequencing and species-specific primers, the isolates were identified as L. brevis LB32 and L. pentosus LP05. In contrast to simulated gastric conditions, the growth rate of the isolates in alkaline conditions of upper intestine increased significantly with the passage of time reaching its maximum in 24 hours. These 2 isolates inhibited the growth of Listeria monocytogenes, Salmonella enteritidis, Shigella dysenteriae, Staphylococcus aureus, and Streptococcus pneumonia. Furthermore, L. brevis LB32 was able to reduce approximately 86% of

The frequency of Listeria monocytogenes strains recovered from clinical and non-clinical samples using phenotypic methods and confirmed by PCR

Directory of Open Access Journals (Sweden)

abazar pournajaf

2013-09-01

Full Text Available Background: Listeria monocytogenes is a facultative intracellular pathogen that causes listeriosis which has extensive clinical manifestations. Infections with L. monocytogenes are a serious threat to immunocompromised persons. The aim of this study was to determine the frequency of L. monocytogenes strains recovered from clinical and non-clinical samples using phenotypic methods and confirmed by PCR. Materials and Methods: In this study, 617 specimens were analyzed. All specimens were cultured in the specific PALCAM agar. Colonies were initially identified by routine biochemical tests. Finally, PCR assays using primers specific for inlA gene were performed. Results: In all, 46 (8.2% L. monocytogenes isolates were recovered from 617 specimens. Fourteen (8.2% strains, including 4 (7.5%, 2 (5.7%, 5 (14.2% and 3 (8.5% isolates were obtained from placental tissue, urine, vaginal and rectal swabs, respectively. In addition, 9 (7.4% strains of L. monocytogenes which were isolated from 107 different dairy products originated from cheese 5 (7.1%, cream 2 (10% and kashk 2 (11.7%, respectively. Among 11 (5.2% strains isolated from 210 different meat products, 5 (5.5%, 4 (7.2% and 2 (3% strains belonged to sausage, meat and poultry extracts, respectively. Finally, 12 (9.2% Listeria strains were recovered from 130 animal specimens that included 6 (10%, 4 (8% and 2 (10% strains from goat, sheep and cattle, respectively. Furthermore, all Listeria isolates (100% were found to be carriers of  inlA gene in PCR assay. Conclusion: The present study showed that the clinical and non-clinical specimens were contaminated with L. monocytogenes. So, it seems necessary to use a simple and standard technique such as PCR for rapid detection of this organism from various sources.

Towards Intelligent Interpretation of Low Strain Pile Integrity Testing Results Using Machine Learning Techniques.

Science.gov (United States)

Cui, De-Mi; Yan, Weizhong; Wang, Xiao-Quan; Lu, Lie-Min

2017-10-25

Low strain pile integrity testing (LSPIT), due to its simplicity and low cost, is one of the most popular NDE methods used in pile foundation construction. While performing LSPIT in the field is generally quite simple and quick, determining the integrity of the test piles by analyzing and interpreting the test signals (reflectograms) is still a manual process performed by experienced experts only. For foundation construction sites where the number of piles to be tested is large, it may take days before the expert can complete interpreting all of the piles and delivering the integrity assessment report. Techniques that can automate test signal interpretation, thus shortening the LSPIT's turnaround time, are of great business value and are in great need. Motivated by this need, in this paper, we develop a computer-aided reflectogram interpretation (CARI) methodology that can interpret a large number of LSPIT signals quickly and consistently. The methodology, built on advanced signal processing and machine learning technologies, can be used to assist the experts in performing both qualitative and quantitative interpretation of LSPIT signals. Specifically, the methodology can ease experts' interpretation burden by screening all test piles quickly and identifying a small number of suspected piles for experts to perform manual, in-depth interpretation. We demonstrate the methodology's effectiveness using the LSPIT signals collected from a number of real-world pile construction sites. The proposed methodology can potentially enhance LSPIT and make it even more efficient and effective in quality control of deep foundation construction.

Damage identification method for continuous girder bridges based on spatially-distributed long-gauge strain sensing under moving loads

Science.gov (United States)

Wu, Bitao; Wu, Gang; Yang, Caiqian; He, Yi

2018-05-01

A novel damage identification method for concrete continuous girder bridges based on spatially-distributed long-gauge strain sensing is presented in this paper. First, the variation regularity of the long-gauge strain influence line of continuous girder bridges which changes with the location of vehicles on the bridge is studied. According to this variation regularity, a calculation method for the distribution regularity of the area of long-gauge strain history is investigated. Second, a numerical simulation of damage identification based on the distribution regularity of the area of long-gauge strain history is conducted, and the results indicate that this method is effective for identifying damage and is not affected by the speed, axle number and weight of vehicles. Finally, a real bridge test on a highway is conducted, and the experimental results also show that this method is very effective for identifying damage in continuous girder bridges, and the local element stiffness distribution regularity can be revealed at the same time. This identified information is useful for maintaining of continuous girder bridges on highways.

Isolation and Antibiotic Sensitivity of Bacillus thuringinesis Strain From Dump Soil

Directory of Open Access Journals (Sweden)

Sarker, D.

2010-01-01

Full Text Available Bacillus thuringiensis (or Bt is a commonly used as a pesticide. B. thuringiensis is a naturally-occurring soil bacterium, also occurs naturally in the gut of caterpillars of various types of moths and butterflies, as well as on the dark surface of plants. The xylanase producing bacterial strains were isolated from dump soil. The strains were isolated on xylan agar media and screening was carried out by xylanolysis method. To test the sensitivity of the isolates, ten different antibiotics were used. The strains were tested for resistance to doxycyclin, erythromycin, chloramphenical, cephallaxin, kanamycin, ampicillin, steptomycin, vancomycin, amoxycillin and neomycin. The strains showed sensitive to doxycyclin, erythromycin, chloramphenical, cephallaxin, kanamycin, ampicillin, steptomycin and vancomycin and also showed resistance to amoxycillin and neomycin, when tested by disc diffusion method on nutrient agar plate confirmed by antibiotic spread plate method. The inhibitory effect of B. thuringiensis strains against the test bacteria Bacillus subtilis, Sarcina lutca, Shigella dysenteriae, Shigella sonnei and Pseudomonus aeruginosa examined. It was found that, B. thuringiensis S1, B. thuringiensis S2 and B. thuringiensis S3 strains showed an inhibitory effect on all of the test bacteria.

Biological assay of attenuated strain NADL-2 and virulent strain NADL-8 of porcine parvovirus.

Science.gov (United States)

Mengeling, W L; Pejsak, Z; Paul, P S

1984-11-01

Attenuated strain NADL-2 and virulent strain NADL-8 of porcine parvovirus (PPV) were titrated in vivo and in vitro under similar conditions to provide a better understanding of some of the factors involved in virulence of PPV in causing maternal reproductive failure of swine. Both strains cause fetal death when they are injected directly into fetal fluids, but only strain NADL-8 does so when administered to pregnant swine. The strains were tested for their hemagglutinating activity (HA), median cell culture infective dose (CCID50), median fetal infective dose (FID50), and median fetal lethal dose (FLD50). The FID50 and FLD50 were determined by injecting virus directly into the amniotic fluid of fetuses in utero at 44 +/- 2 days of gestation and collecting the fetuses 15 +/- 1 days later. Both strains had an HA titer of 64, suggesting that there is a similar number of virions in stock preparations. However, other measurements differed markedly. The CCID50, FID50, and FLD50 were 10(5.5), 10(3.5), and 10(0.5), respectively, for strain NADL-2, and 10(4.5), 10(7.7), and 10(6.3), respectively, for strain NADL-8. Collectively, the values indicate that more than 10,000 times as much strain NADL-2 would need to reach the conceptus transplacentally to establish infection. These observations may help to explain the different consequences of oronasal exposure of pregnant swine to these strains of PPV.

In vitro investigation of Debaryomyces hansenii strains for potential probiotic properties

DEFF Research Database (Denmark)

Ochangco, Honeylet Sabas; Gamero, Amparo; Smith, Ida Mosbech

2016-01-01

and mucin, and (3) modulation of pro- and anti-inflammatory cytokine secretion by human monocyte-derived dendritic cells. As references two commercially available probiotic Saccharomyces cerevisiae var. boulardii (S. boulardii) strains were included in the study. Our results demonstrate that the different D....... hansenii yeast strains had very diverse properties which could potentially lead to different probiotic effects. One strain of D. hansenii (DI 09) was capable of surviving GI stress conditions, although not to the same degree as the S. boulardii strains. This DI 09 strain, however, adhered more strongly...... to Caco-2 cells and mucin than the S. boulardii strains. Additionally, two D. hansenii strains (DI 10 and DI 15) elicited a higher IL-10/IL-12 ratio than the S. boulardii strains, indicating a higher anti-inflammatory effects on human dendritic cells. Finally, one strain of D. hansenii (DI 02...

Final report proficiency test on the determination of α, β and γ-emitting radionuclides

International Nuclear Information System (INIS)

Shakhashiro, A.; Trinkl, A.; Benesch, T.; Sansone, U.

2005-06-01

A proficiency test on the determination of α, β and γ-emitting radionuclides was organised within the frame of the Technical Cooperation project: RAS/9/024 'Environmental Radiation Monitoring and Regional Data Base' to evaluate the analytical performance of 14 laboratories from 12 Asian countries. This report summarises the performance evaluation of the participating laboratories. Analytical data evaluation of this proficiency test showed that 58% of all reported results obtained a 'Passed' final score for both the trueness and precision criteria applied to this exercise. (author)

Behavior of quenched and tempered steels under high strain rate compression loading

International Nuclear Information System (INIS)

Meyer, L.W.; Seifert, K.; Abdel-Malek, S.

1997-01-01

Two quenched and tempered steels were tested under compression loading at strain rates of ε = 2.10 2 s -1 and ε = 2.10 3 s -1 . By applying the thermal activation theory, the flow stress at very high strain rates of 10 5 to 10 6 s -1 is derived from low temperature and high strain rate tests. Dynamic true stress - true strain behaviour presents, that stress increases with increasing strain until a maximum, then it decreases. Because of the adiabatic process under dynamic loading the maximum flow stress will occur at a lower strain if the strain rate is increased. Considering strain rate, strain hardening, strain rate hardening and strain softening, a constitutive equation with different additive terms is successfully used to describe the behaviour of material under dynamic compression loading. Results are compared with other models of constitutive equations. (orig.)

Final report on in-reactor creep-fatigue deformation behaviour of a CuCrZr alloy: COFAT 2

International Nuclear Information System (INIS)

Singh, B.N.; Johansen, B.S.; Taehtinen, S.; Moilanen, P.; Saarela, S.; Jacquet, P.; Dekeyser, J.; Stubbins, J.F.

2008-01-01

The main objective of the present work was to determine experimentally the mechanical response and resulting microstructural changes in CuCrZr (HT1) alloy exposed concurrently to flux of neutrons and creep-fatigue cyclic loading directly in a fission reactor. Using specially designed test facilities for this purpose, in-reactor creep-fatigue tests have been performed at strain amplitudes of 0.25 and 0.35 % with a holdtime of 10s in the BR-2 reactor at Mol (Belgium). These tests were performed at the ambient temperatures of 326K and 323K. For comparison purposes corresponding out-of-reactor creep-fatigue tests were also carried out. In the following we first describe the details of the creep-fatigue experiments. We then present the main results on the mechanical response of the material in the form of hysteresis loops and the maximum stress amplitude as a function of the number of creep-fatigue cycles during the out-of-reactor and the in-reactor tests carried out at different strain amplitudes. Finally, the dependence of the number of cycles to failure (i.e. creep-fatigue lifetime) on the strain amplitudes is shown. The details of microstructure of the specimens tested out-of-reactor as well as in the reactor were investigated using transmission electron microscopy. The main results on the mechanical response as well as changes in the microstructure are briefly discussed. The main conclusion emerging from the present work is that the lifetime of the in-reactor tested specimens is by a factor of about two longer than in the case of corresponding out-of-reactor tests. (au)

Chemometric Analysis of the Volatile Compounds Generated by Aspergillus carbonarius Strains Isolated from Grapes and Dried Vine Fruits

Directory of Open Access Journals (Sweden)

Zhan Cheng

2018-02-01

Full Text Available Ochratoxin A (OTA contamination in grape production is an important problem worldwide. Microbial volatile organic compounds (MVOCs have been demonstrated as useful tools to identify different toxigenic strains. In this study, Aspergillus carbonarius strains were classified into two groups, moderate toxigenic strains (MT and high toxigenic strains (HT, according to OTA-forming ability. The MVOCs were analyzed by GC-MS and the data processing was based on untargeted profiling using XCMS Online software. Orthogonal projection to latent structures discriminant analysis (OPLS-DA was performed using extract ion chromatogram GC-MS datasets. For contrast, quantitative analysis was also performed. Results demonstrated that the performance of the OPLS-DA model of untargeted profiling was better than the quantitative method. Potential markers were successfully discovered by variable importance on projection (VIP and t-test. (E-2-octen-1-ol, octanal, 1-octen-3-one, styrene, limonene, methyl-2-phenylacetate and 3 unknown compounds were selected as potential markers for the MT group. Cuparene, (Z-thujopsene, methyl octanoate and 1 unknown compound were identified as potential markers for the HT groups. Finally, the selected markers were used to construct a supported vector machine classification (SVM-C model to check classification ability. The models showed good performance with the accuracy of cross-validation and test prediction of 87.93% and 92.00%, respectively.

Strain features and condition assessment of orthotropic steel deck cable-supported bridges subjected to vehicle loads by using dense FBG strain sensors

Science.gov (United States)

Wei, Shiyin; Zhang, Zhaohui; Li, Shunlong; Li, Hui

2017-10-01

Strain is a direct indicator of structural safety. Therefore, strain sensors have been used in most structural health monitoring systems for bridges. However, until now, the investigation of strain response has been insufficient. This paper conducts a comprehensive study of the strain features of the U ribs and transverse diaphragm on an orthotropic steel deck and proposes a statistical paradigm for crack detection based on the features of vehicle-induced strain response by using the densely distributed optic fibre Bragg grating (FBG) strain sensors. The local feature of strain under vehicle load is highlighted, which enables the use of measurement data to determine the vehicle loading event and to make a decision regarding the health status of a girder near the strain sensors via technical elimination of the load information. Time-frequency analysis shows that the strain contains three features: the long-term trend item, the short-term trend item, and the instantaneous vehicle-induced item (IVII). The IVII is the wheel-induced strain with a remarkable local feature, and the measured wheel-induced strain is only influenced by the vehicle near the FBG sensor, while other vehicles slightly farther away have no effect on the wheel-induced strain. This causes the local strain series, among the FBG strain sensors in the same transverse locations of different cross-sections, to present similarities in shape to some extent and presents a time delay in successive order along the driving direction. Therefore, the strain series induced by an identical vehicle can be easily tracked and compared by extracting the amplitude and calculating the mutual ratio to eliminate vehicle loading information, leaving the girder information alone. The statistical paradigm for crack detection is finally proposed, and the detection accuracy is then validated by using dense FBG strain sensors on a long-span suspension bridge in China.

Strain Measurement System Developed for Biaxially Loaded Cruciform Specimens

Science.gov (United States)

Krause, David L.

2000-01-01

A new extensometer system developed at the NASA Glenn Research Center at Lewis Field measures test area strains along two orthogonal axes in flat cruciform specimens. This system incorporates standard axial contact extensometers to provide a cost-effective high-precision instrument. The device was validated for use by extensive testing of a stainless steel specimen, with specimen temperatures ranging from room temperature to 1100 F. In-plane loading conditions included several static biaxial load ratios, plus cyclic loadings of various waveform shapes, frequencies, magnitudes, and durations. The extensometer system measurements were compared with strain gauge data at room temperature and with calculated strain values for elevated-temperature measurements. All testing was performed in house in Glenn's Benchmark Test Facility in-plane biaxial load frame.

Full-field Strain Analysis of a Ski Boot

Science.gov (United States)

Reiter, M.; Singer, G.; Major, Z.

2010-06-01

The quality of the ski boots plays an extraordinary important role in the performance and in the safety of the skiers. The deformation behavior of a racing class ski boot was characterized by using the digital image correlation technique in this study. The boot was gripped in the ski binding and 3 types of motions of the skiers and the deformations of the boot were simulated by a professional skier in the laboratory. First, the buckles were closed in 4 stages and the resulting strains were measured. Furthermore, the skier positioned his balance continuously forward, resulting in a high overall bending deformation of the boot. The leg of the skier acted as a bending arm and pushed the upper part of the boot forward. This loading situation was assumed as quasistatic and was repeated several times. Finally, the skier jumped and this dynamic movement was recorded by using two high speed cameras for 3D analysis. Special focus was devoted to the measurement of the deformation of the boot during the contact of the ski with the ground of the laboratory. Both the displacement of the upper part and the local strain in selected areas of the boot was determined for both quasi-static and dynamic test conditions and are discussed in the paper.

Testing of GFL Geosiphon; FINAL

International Nuclear Information System (INIS)

Steimke, J.L.

2001-01-01

A full-scale, transparent replica of a GeoSiphon was constructed in the TFL to test a new concept, using a solar powered vacuum pump to remove accumulated gases from the air chamber. It did not have a treatment cell containing iron filings as do the actual TNX GeoSiphons in the field, but it was accurate in all other respects. The gas generation that is observed in an actual GeoSiphon was simulated by air injection at the inlet of the TFL GeoSiphon. After facility shakedown, three stages of testing were conducted: verification testing, parametric testing and long term testing. In verification testing, the TFL GeoSiphon was used to reproduce a particular test at TNX in which the water flowrate decreased gradually as the result of air accumulation at the crest of a siphon without an air chamber. For this test the vacuum pump was not used and the air chamber was initially filled with air rather than water. Agreement between data from the TNX GeoSiphon and the TFL GeoSiphon was good, which gave confidence that the TFL GeoSiphon was a good hydraulic representation of the TNX GeoSiphon. For the remaining tests, the solar powered vacuum pump and air chamber were used. In parametric testing, steady state runs were made for water flowrates ranging from 1 gpm to 19 gpm, air injection rates ranging from 0 to 77 standard cc/min and outfall line angles ranging from vertical to 60 degrees from vertical. In all cases, the air chamber and vacuum pump removed nearly all of the air and the GeoSiphon operated without problems. In long term testing, the GeoSiphon was allowed to run continuously for 21 days at one set of conditions. During this time the solar cell kept the storage battery fully charged at all times and the control circuit for the vacuum pump operated reliably. The solar panel was observed to have a large excess capacity when used with the vacuum pump. With two changes, the concept of using a solar powered vacuum pump attached to an air chamber should be ready for long

Molecular typing of Brucella melitensis endemic strains and differentiation from the vaccine strain Rev-1.

Science.gov (United States)

Noutsios, Georgios T; Papi, Rigini M; Ekateriniadou, Loukia V; Minas, Anastasios; Kyriakidis, Dimitrios A

2012-03-01

In the present study forty-four Greek endemic strains of Br. melitensis and three reference strains were genotyped by Multi locus Variable Number Tandem Repeat (ML-VNTR) analysis based on an eight-base pair tandem repeat sequence that was revealed in eight loci of Br. melitensis genome. The forty-four strains were discriminated from the vaccine strain Rev-1 by Restriction Fragment Length Polymorphism (RFLP) and Denaturant Gradient Gel Electrophoresis (DGGE). The ML-VNTR analysis revealed that endemic, reference and vaccine strains are genetically closely related, while most of the loci tested (1, 2, 4, 5 and 7) are highly polymorphic with Hunter-Gaston Genetic Diversity Index (HGDI) values in the range of 0.939 to 0.775. Analysis of ML-VNTRs loci stability through in vitro passages proved that loci 1 and 5 are non stable. Therefore, vaccine strain can be discriminated from endemic strains by allele's clusters of loci 2, 4, 6 and 7. RFLP and DGGE were also employed to analyse omp2 gene and reveled different patterns among Rev-1 and endemic strains. In RFLP, Rev-1 revealed three fragments (282, 238 and 44 bp), while endemic strains two fragments (238 and 44 bp). As for DGGE, the electrophoretic mobility of Rev-1 is different from the endemic strains due to heterologous binding of DNA chains of omp2a and omp2b gene. Overall, our data show clearly that it is feasible to genotype endemic strains of Br. melitensis and differentiate them from vaccine strain Rev-1 with ML-VNTR, RFLP and DGGE techniques. These tools can be used for conventional investigations in brucellosis outbreaks.

Strain-induced corrosion cracking in ferritic components of BWR primary circuits

International Nuclear Information System (INIS)

Seifert, H.-P.; Ritter, S.; Ineichen, U.; Tschanz, U.; Gerodetti, B.

2003-04-01

The present final report of the RIKORR project is a summary of a literature survey and of the experimental work performed by PSI on the environmentally-assisted cracking (EAC) and dynamic strain ageing (DSA) susceptibility of low-alloy steels (LAS) in high-temperature (HT) water. Within this project, the EAC crack growth behaviour of different low-alloy RPV steels, weld filler and weld heat-affected zone materials has been investigated under simulated transient and steady-state BWR/NWC power operation conditions. The strain-induced corrosion cracking (SICC) / low-frequency corrosion fatigue (CF) and stress corrosion cracking (SCC) crack growth behaviour of different low-alloy RPV steels under simulated transient and stationary BWR/NWC conditions was characterized by slow rising load / low-frequency corrosion fatigue and constant load / periodical partial unloading / ripple load tests with pre-cracked fracture mechanics specimens in oxygenated HT water at temperatures of either 288, 250, 200 or 150 o C. Modern high-temperature water loops, on-line crack growth monitoring and fractographic analysis by scanning electron microscopy (SEM) were used to quantify the cracking response. (author)

Relating high-temperature flow stress of AISI 316 stainless steel to strain and strain rate

International Nuclear Information System (INIS)

Matteazzi, S.; Paitti, G.; Boerman, D.

1982-01-01

The authors have performed an experimental determination of tensile stress-strain curves for different strain rates (4.67 x 10 - 5 , 4.67 x 10 - 2 s - 1 ) and for a variety of temperature conditions (773-1073 K) of AISI 316H stainless steel (annealed conditions) and also a computer analysis of the experimental curves using a fitting program which takes into consideration different constitutive relations describing the plastic flow behaviour of the metals. The results show that the materials tested are clearly affected by strain rate only at the highest temperature investigated (1073 K) and that the plastic strain is the more significant variable. Of the constitutive equations considered, Voce's relation gives the best fit for the true stress-time-strain curves. However, the Ludwik and Ludwigson equations also provide a description of the experimental data, whereas Hollomon's equation does not suitably characterize AISI 316H stainless steel and can be applied with some accuracy only at 1073 K. (author)

Sanitary landfill in situ bioremediation optimization test. Final report

International Nuclear Information System (INIS)

1996-01-01

This work was performed as part of a corrective action plan for the Savannah River Site Sanitary Landfill. This work was performed for the Westinghouse Savannah River Company Environmental Restoration Department as part of final implementation of a groundwater remediation system for the SRS Sanitary Landfill. Primary regulatory surveillance was provided by the South Carolina Department of Health and Environmental Control and the US Environmental Protection Agency (Region IV). The characterization, monitoring and remediation systems in the program generally consisted of a combination of innovative and baseline methods to allow comparison and evaluation. The results of these studies will be used to provide input for the full-scale groundwater remediation system for the SRS Sanitary Landfill. This report summarizes the performance of the Sanitary Landfill In Situ Optimization Test data, an evaluation of applicability, conclusions, recommendations, and related information for implementation of this remediation technology at the SRS Sanitary Landfill

Testing of components on the shaking table facilities of AEP and contribution to full scale dynamic testing of Kozloduy NPP. Final report

International Nuclear Information System (INIS)

Ambriashvili, Y.

1996-01-01

This final report summarizes the results of components testing on the shaking table facilities of 'Atomenergoproject' which are considered as a contribution to the full scale dynamic testing of the Kozloduy nuclear power plant Units 5 and 6. It was designed on 1.0 g according to the calculations that were based on accelerograms which included artificial and already known recordings of real earthquakes. Maximum acceleration of the designed spectrum and new spectrum which are recommended are now within the range of frequencies 2.5-20 Hz. Active reactor and the primary loop are seismic stable as well as the tested equipment tested by 'Atomenergoproject'

TFTR Inner Support Structure final assembly and installation

International Nuclear Information System (INIS)

Rocco, R.E.; Brown, G.; Carglia, G.; Heitzenroeder, P.; Koenig, F.; Mookerjee, S.; Raugh, J.

1983-01-01

The Inner Support Structure (ISS) of the TFTR provides a specific level of restraint to the net centering force and overturning moment produced by the Toroidal Field (TF) coils and to the vertical forces produced by the Inner Poloidal Field (PF) coils. This is accomplished consistent with the need for four radial dielectric breaks running the entire length of the ISS to prevent eddy current loops. A brief description of the major components, method of manufacture and material selection of the ISS and PF coils is presented. Particular attention is given to the integration of the PF coils and the ISS components into the total assembly and the installation of strain gauges and crack monitors on the ISS. The requirements of no gaps at the interfaces of the ISS teeth at all three horizontal planes is discussed. The problem encountered with achieving the no gap requirement and the successful resolution of this problem, including its impact on installation of the ISS, is also discussed. The installation of the ISS, including setting in position, preloading with TF coil clips, and final tensioning of the tension bars is discussed. A brief description of the lower and upper lead stem splicing operation is presented. Subsequent to the final assembly, electrical tests were performed prior to and after installation on the TFTR machine. An overview of the tests and their results is presented

Proof that Burkholderia Strains Form Effective Symbioses with Legumes: a Study of Novel Mimosa-Nodulating Strains from South America

Science.gov (United States)

Chen, Wen-Ming; de Faria, Sergio M.; Straliotto, Rosângela; Pitard, Rosa M.; Simões-Araùjo, Jean L.; Chou, Jui-Hsing; Chou, Yi-Ju; Barrios, Edmundo; Prescott, Alan R.; Elliott, Geoffrey N.; Sprent, Janet I.; Young, J. Peter W.; James, Euan K.

2005-01-01

Twenty Mimosa-nodulating bacterial strains from Brazil and Venezuela, together with eight reference Mimosa-nodulating rhizobial strains and two other β-rhizobial strains, were examined by amplified rRNA gene restriction analysis. They fell into 16 patterns and formed a single cluster together with the known β-rhizobia, Burkholderia caribensis, Burkholderia phymatum, and Burkholderia tuberum. The 16S rRNA gene sequences of 15 of the 20 strains were determined, and all were shown to belong to the genus Burkholderia; four distinct clusters could be discerned, with strains isolated from the same host species usually clustering very closely. Five of the strains (MAP3-5, Br3407, Br3454, Br3461, and Br3469) were selected for further studies of the symbiosis-related genes nodA, the NodD-dependent regulatory consensus sequences (nod box), and nifH. The nodA and nifH sequences were very close to each other and to those of B. phymatum STM815, B. caribensis TJ182, and Cupriavidus taiwanensis LMG19424 but were relatively distant from those of B. tuberum STM678. In addition to nodulating their original hosts, all five strains could also nodulate other Mimosa spp., and all produced nodules on Mimosa pudica that had nitrogenase (acetylene reduction) activities and structures typical of effective N2-fixing symbioses. Finally, both wild-type and green fluorescent protein-expressing transconjugant strains of Br3461 and MAP3-5 produced N2-fixing nodules on their original hosts, Mimosa bimucronata (Br3461) and Mimosa pigra (MAP3-5), and hence this confirms strongly that Burkholderia strains can form effective symbioses with legumes. PMID:16269788

Influence of the static strain ageing on the ductile-to-brittle transition in C-Mn steel

International Nuclear Information System (INIS)

Marais, A.

2012-01-01

Ferritic steels for industrial structures have a brittle-ductile transition toughness and impact energy with temperature. Their resistance to the brittle fracture plays an essential role in the safety certification of industrial structures. Nowadays, the performance and the durability are key issues for major players such as EDF. In these approaches ductile-to-brittle transition toughness and impact energy, toughness is predicted from resilience. Several previous studies have shown that the probability of cleavage fracture can be adequately described in brittle plateau by a local approach to fracture. However, these studies assume that the material does not undergo strain aging, which is rarely relevant for low carbon steels and low calmed down. The work consisted firstly to characterize the behavior and secondly to propose a robust and explicit modeling of the observed phenomena. Characterization consisted of performing tensile tests between -150 C and 20 C for several strain rates. A model able to simulate the static aging is identified by implementing an appropriate and systematic strategy. Impact resistance test allows us to build the curve of ductile-to-brittle transition of the material for different conditions to understand and observe the influence of static strain aging on the failure. Finally, the modeling of the brittle fracture has been described for all experimental conditions tested using the model developed and identified in the previous section to predict the transition for different material conditions. (author)

Sensitivity Enhancement of FBG-Based Strain Sensor.

Science.gov (United States)

Li, Ruiya; Chen, Yiyang; Tan, Yuegang; Zhou, Zude; Li, Tianliang; Mao, Jian

2018-05-17

A novel fiber Bragg grating (FBG)-based strain sensor with a high-sensitivity is presented in this paper. The proposed FBG-based strain sensor enhances sensitivity by pasting the FBG on a substrate with a lever structure. This typical mechanical configuration mechanically amplifies the strain of the FBG to enhance overall sensitivity. As this mechanical configuration has a high stiffness, the proposed sensor can achieve a high resonant frequency and a wide dynamic working range. The sensing principle is presented, and the corresponding theoretical model is derived and validated. Experimental results demonstrate that the developed FBG-based strain sensor achieves an enhanced strain sensitivity of 6.2 pm/με, which is consistent with the theoretical analysis result. The strain sensitivity of the developed sensor is 5.2 times of the strain sensitivity of a bare fiber Bragg grating strain sensor. The dynamic characteristics of this sensor are investigated through the finite element method (FEM) and experimental tests. The developed sensor exhibits an excellent strain-sensitivity-enhancing property in a wide frequency range. The proposed high-sensitivity FBG-based strain sensor can be used for small-amplitude micro-strain measurement in harsh industrial environments.

Gender and General Strain Theory: A Comparison of Strains, Mediating, and Moderating Effects Explaining Three Types of Delinquency

Science.gov (United States)

Moon, Byongook; Morash, Merry

2017-01-01

The present study of 659 Korean adolescents tests General Strain Theory's (GST) utility in explaining gender differences in delinquency causation. It models the effects of key strains, negative emotions, and a composite measure of several conditioning factors separately for boys and girls and for delinquency. Consistent with the theory, males and…

Organic metabolites produced by Vibrio parahaemolyticus strain ...

African Journals Online (AJOL)

Identification and action of several antibacterial metabolites produced by a fish pathogen Vibrio parahaemolyticus strain An3 from marine ecosystem of Goa has been demonstrated. Antibacterial activity of the crude cell extract of the test bacterium has been evaluated against indicator pathogenic bacterial strains such as ...

Strain ageing in welds of nuclear pressure vessels

International Nuclear Information System (INIS)

Otterberg, R.; Karlsson, C.

1979-01-01

Static and dynamic strain ageing have been investigated on submerged-arc welds and repair welds from plates of the pressure vessel steel A 533B. The results permit the determination of the worst strain ageing conditions existing in a nuclear pressure vessel. Static strain ageing was investigated by means of data from tension tests, hardness measurements and Charpy-V impact properties for prestrained and aged material for ageing temperatures from room temperature to 350 deg C and ageing times up to 1000h. Dynamic strain ageing was investigated by tensile tests up to 350 deg C at different strain rates. At the most static strain ageing was found to increase the impact transition temperature from -75 deg C in the as-received condition to -55 deg C after prestraining and ageing for the plate material, from -35 to -10 deg C for the submerged arc weld and from -90 to -40 deg C for the repair weld. Approximately 10 deg C of the deleterious effect is due to the effect of ageing for the two former materials whereas the corresponding figure for the repair weld amounts to 35 deg C. The dynamic strain ageing is strongest at very low strain rates at temperatures just below 300 deg C. The effect of strain ageing can be reduced by stress relief heat treatment or by other means decreasing the content of nitrogen in solution. (author)

Polydimethylsiloxane (PDMS-Based Flexible Resistive Strain Sensors for Wearable Applications

Directory of Open Access Journals (Sweden)

Jing Chen

2018-02-01

Full Text Available There is growing attention and rapid development on flexible electronic devices with electronic materials and sensing technology innovations. In particular, strain sensors with high elasticity and stretchability are needed for several potential applications including human entertainment technology, human–machine interface, personal healthcare, and sports performance monitoring, etc. This article presents recent advancements in the development of polydimethylsiloxane (PDMS-based flexible resistive strain sensors for wearable applications. First of all, the article shows that PDMS-based stretchable resistive strain sensors are successfully fabricated by different methods, such as the filtration method, printing technology, micromolding method, coating techniques, and liquid phase mixing. Next, strain sensing performances including stretchability, gauge factor, linearity, and durability are comprehensively demonstrated and compared. Finally, potential applications of PDMS-based flexible resistive strain sensors are also discussed. This review indicates that the era of wearable intelligent electronic systems has arrived.

Buckling Test Results from the 8-Foot-Diameter Orthogrid-Stiffened Cylinder Test Article TA01. [Test Dates: 19-21 November 2008