WorldWideScience

Sample records for steel-cr18

  1. Changes of surface structure of Ni, W and chromium-nickel steel Cr18Ni10 irradiated by high fluences of krypton ions with high energies

    International Nuclear Information System (INIS)

    Didyk, A.Yu.; Semina, V.K.; Khalil, A.; Suvorov, A.L.; Stepanov, A.Eh.; Cheblukov, Yu.N.

    1999-01-01

    The surfaces of W single crystal, Ni polycrystal and chromium-nickel steel, irradiated by Kr ions with energy 305 and 245 MeV up to the fluences 2*10 15 and 3*10 15 ion/cm 2 , were studied by means of scanning electron microscopy. The evaporation coefficients of material surfaces were estimated on the base of changes of surface relief. The values of these coefficients turned out much more than ones predicted by the inelastic sputtering model. The method of 'step' was offered and realized for the more correct estimations evaporation coefficient on the Ni example. The phenomenological model explaining the observed phenomena is introduced

  2. Corrosion tests in Baltic sea water on heat exchanger tubes of various metallic materials

    International Nuclear Information System (INIS)

    Henrikson, S.; Knutsson, L.

    1975-05-01

    Seventeen different tube materials have been exposed to continuous and intermittent flow in Baltic Sea water (0.4 % Cl - ) at 50 deg C for a maximum of 15 000 hours. During testing the specimens have been examined at certain intervals. After testing the specimens have been examined visually and metallographically. The following materials were completely resistant: titanium, CuNi30Mn1Fe, Alloy 825 and the austenitic steels Cr18Ni24Mo4.5, Cr20Ni25Mo4.5Cu and Cr24Ni24Mo2Ti. The ferritic-austenitic steels Cr18Ni5Mo2Si and Cr25Ni5Mo1.5 on the other hand, seem to be attacked by local intercrystalline corrosion in the vicinity of the welds. The same type of attack occurs, against expectations, even in the entirely ferritic steels, especially in Cr21Mo3Ti; this attack was however shown to be caused by surface carburization. Admiralty brass (2.5 m/s), aluminium brass (3.0 m/s) and CuNi10Fe1Mn (3.5 m/s) have been attacked by erosion corrosion. The same type of attack, although to a considerably smaller extent, has also been observed for the three aluminium materials (2.5 m/s). (author)

  3. Neutron diffraction measurements of residual stresses in NPP construction materials

    International Nuclear Information System (INIS)

    Hinca, R.; Bokuchava, G.

    2001-01-01

    Neutron diffraction is one of the most powerful methods for condensed matter studies. This method is used for non-destructive determination of residual stresses in material. The fundamental aspects of neutron diffraction are discussed, together with a brief description of the experimental facility. The principal advantage of using neutrons rather than the more conventional X-rays is the fact that neutron can penetrate deeply (2-4 cm for steel and more than 10 cm for aluminium) into metals to determine internal parameters within the bulk of materials. We present results of measurements residual stresses in NPP construction material - austenitic stainless steel (Cr-18%, Ni-10%, Ti-1%) coated with high-nickel alloy. (authors)

  4. Study of the plasma immersion implantation of titanium in stainless steel

    International Nuclear Information System (INIS)

    Nikitenkov, N N; Sutygina, A N; Shulepov, I A; Sivin, D O; Kashkarov, E B

    2015-01-01

    The results of the study of the pulsed plasma-immersion ion implantation of titanium in steel Cr18Ni10Ti depending on the time (dose) implantation are presented. It is shown that the change of the element and the phase composition of the surface layers and their microscopic characteristics and mechanical properties (hardness, wear resistance) depending on the implantation time is not monotonic, but follows to a certain rule. The possibility of interpretation of the obtained results in the thermal spike concept of the generation on the surface by the stable (magic) clusters is discussed. This concept follows logically from the recent studies on the plasma arc composition and from a polyatomic clusters-surface interaction. (paper)

  5. Study of the plasma immersion implantation of titanium in stainless steel

    Science.gov (United States)

    Nikitenkov, N. N.; Sutygina, A. N.; Shulepov, I. A.; Sivin, D. O.; Kashkarov, E. B.

    2015-04-01

    The results of the study of the pulsed plasma-immersion ion implantation of titanium in steel Cr18Ni10Ti depending on the time (dose) implantation are presented. It is shown that the change of the element and the phase composition of the surface layers and their microscopic characteristics and mechanical properties (hardness, wear resistance) depending on the implantation time is not monotonic, but follows to a certain rule. The possibility of interpretation of the obtained results in the thermal spike concept of the generation on the surface by the stable (magic) clusters is discussed. This concept follows logically from the recent studies on the plasma arc composition and from a polyatomic clusters-surface interaction.

  6. Material Science Activities for Fusion Reactors in Kazakhstan

    International Nuclear Information System (INIS)

    Tazhibayeva, I.; Kenzhin, E.; Kulsartov, T.; Shestakov, V.; Chikhray, Y.; Azizov, E.; Filatov, O.; Chernov, V.M.

    2007-01-01

    Full text of publication follows: Paper contains results of fusion material testing national program and results of activities on creation of material testing spherical tokamak. Hydrogen isotope behavior (diffusion, permeation, and accumulation) in the components of the first wall and divertor was studied taking into account temperature, pressure, and reactor irradiation. There were carried out out-of-pile and in-pile (reactors IVG-IM, WWRK, RA) studies of beryllium of various grades (TV-56, TShG-56, DV-56, TGP-56, TIP-56), graphites (RG-T, MPG-8, FP 479, R 4340), molybdenum, tungsten, steels (Cr18Ni10Ti, Cr16Ni15, MANET, F82H), alloys V-(4-6)Cr-( 4-5)Ti, Cu+1%Cr+0.1%Zr, and double Be/Cu and triple Be/Cu/steel structures. Tritium permeability from eutectic Pb+17%Li through steels Cr18Ni10Ti, Cr16Ni15, MANET, and F82H were studied taking into account protective coating effects. The tritium production rate was experimentally assessed during in-pile and post-reactor experiments. There were carried out radiation tests of ceramic Li 2 TiO 3 (96% enrichment by Li-6) with in-situ registration of released tritium and following post-irradiation material tests of irradiated samples. Verification of computer codes for simulation of accidents related to LOCA in ITER reactor was carried out. Codes' verification was carried out for a mockup of first wall in a form of three-layer cylinder of beryllium, bronze (Cu-Cr-Zr) and stainless steel. At present Kazakhstan Tokamak for Material testing (tokamak KTM) is created in National Nuclear Center of Republic of Kazakhstan in cooperation with Russian Federation organizations (start-up is scheduled on 2008). Tokamak KTM allows for expansion and specification of the studies and tests of materials, protection options of first wall, receiving divertor tiles and divertor components, methods for load reduction at divertor, and various options of heat/power removal, fast evacuation of divertor volume and development of the techniques for