The effect of thermoplastic treatment regimes on the microplastic strain of nitrogen-containing steel Kh21G10N7MBF

International Nuclear Information System (INIS)

Bannykh, O.A.; Blinov, V.M.; Kostina, M.V.; Grachev, S.V.; Mal'tseva, L.A.

2005-01-01

A study is made into the influence of a percentage reduction during cold rolling and subsequent holdings at heat on development of microplastic deformation when bending sheet specimens of stainless austenitic high-nitrogen steel Kh21G10N7MBF. It is revealed that a maximum value of apparent limit of elasticity (∼1800 MPa) is attained due to plastic deformation by rolling at 20 Deg C with a total percentage reduction of 60 % and subsequent aging at 500 Deg C for 1-4 h [ru

Ductility of high chromium stainless steels

International Nuclear Information System (INIS)

Peretyat'ko, V.N.; Kazantsev, A.A.

1997-01-01

Aimed to optimize the hot working conditions for high chromium stainless steels the experiments were carried in the temperature range of 800-1300 deg C using hot torsion tests and cylindrical specimens of ferritic and ferritic-martensitic steels 08Kh13, 12Kh13, 20Kh13, 30Kh13 and 40Kh13. Testing results showed that steel plasticity varies in a wide range depending on carbon content. Steels of lesser carbon concentration (08Kh13 and 12Kh13) exhibit a sharp increase in plasticity with a temperature rise, especially in the interval of 1200-1250 deg C. Steels 20Kh13 and 30Kh13 display insignificant plasticity increasing, whereas plastic properties of steel 40Kh13 increase noticeably in the range of 1000-1300 deg C. It is shown that optimal hot working conditions for specific steel must be selected with account of steel phase composition at high temperatures

Low-temperature nitriding of austenitic steel in a vibrofluidized bed

Science.gov (United States)

Baraz, V. R.; Grachev, S. V.

1999-11-01

The prospects for use of a vibrofluidized bed (VFB) for low-temperature nitrogen saturation of high-strength austenitic steel based on Cr-Ni-Mn (12Kh17N8G2S2MF) are considered. The positive effect of preliminary plastic deformation on the intensity of nitriding is described. The temperature and time parameters of nitriding in a VFB for strain-aging austenitic steel 12Kh17N8G2S2MF are shown to be adequate for the regimes of the final heat-treatment operation of aging. This creates the possibility of combining the operations of surface alloying and strain aging into a single cycle. This combined treatment increases substantially the resistance of the steel to cyclic loads while preserving the strength parameters. It is shown that the presented method of low-temperature nitriding in a VFB is expedient for improving the service characteristics of austenitic steel 12Kh17N8G2S2MF used for production of force springs of automobile brake systems.

Ultrasound surface treatment of Kh18N10T steel with different structural state. Ul'trazvukovaya poverkhnostnaya obrabotka stali Kh18N10T s razlichnym strukturnym sostoyaniem

Energy Technology Data Exchange (ETDEWEB)

Aksenov, V K; Danilov, P A; Mats, A V; Netesov, V M; Yaes, A A [AN Ukrainskoj SSR, Kharkov (Ukrainian SSR). Fiziko-Tekhnicheskij Inst.

1989-09-01

Ultrasound surface treatment (USST) is studied for its effect on the structure and mechanical-and-physical properties of Kh18N10T steel with different prehistory. It is shown that surface treatment may both increase and decrease steel microhardness.

Welding of high-strength stainless steel 03Kh12N10MT for cryogenic engineering

International Nuclear Information System (INIS)

Pustovit, A.I.

1989-01-01

Consideration is being given to weld resistance to cold and hot cracking at 93 and 77K and to mechanical properties of welded joints of high-strength stainless steel 03Kh12N10MT, produced under the fluxes AN-17M, AN-18, AN-26, AN-45, ANF-5, 48-OF-6, ANK-45 and ANK-49 in combination with various welding wires. It is shown that welds on 03Kh12N10MT steel meet the requirements only when using 48-OF-6 or ANK-49 flux. It is noted that impact strength of welds at 77K is sufficiently affected by the volume fraction of non-metallic inclusions in weld metal

Effect of Cr, Ni, and Mo additions on the susceptibility of the 0Kh6n7m7c steel to hot cracking

International Nuclear Information System (INIS)

Tolstykh, L.G.; Pryakhin, A.V.; Popov, A.N.; Usynin, V.F.

1977-01-01

The effect of chromium, molybdenum, and nickel on the tendency of surfacing materials to form hot cracks (Vsub(kp) was studied using the mathematical statistics method. The St3 steel and 38KhN3MFA steel were used in the study. A device facilitating the hot cracking tendency test procedure was developed. It was found that, in the concentration range involved, Ni and Mo produce no effect on Vsub(kp), and Cr enhances it. A new powder wire, PP-OKh7N8M6S, capable of increasing surface material resistance by 1.5-2 times, has been developed

Development of plastic deformations in 12Kh18N10T steel under cyclic symmetrical bending of specimens of various length

Energy Technology Data Exchange (ETDEWEB)

Pisarenko, G.S.; Leonets, V.A.; Bega, N.D. (AN Ukrainskoj SSR, Kiev. Inst. Problem Prochnosti)

1983-08-01

Effect of specimen length on intensity of plastic deformation development and cyclic strength is studied for annealed 12Kh18N10T steel under cyclic symmetrical bending. The intensity of microplastic deformations and cyclic strength of annealed 12Kh18N10T steel in the considered case is due to self-heating.

Influence of local microplastic strains on stress corrosion of 08Kh18N10T steel

International Nuclear Information System (INIS)

Moskvin, L.N.; Efimov, A.A.; Sherman, Ya.I.; Fedorova, T.I.

1987-01-01

Study on specific features of microhomogeneous strain in the process of plastic strain development and their role in stress corrosion of 08Kh18N10T steel sheet specimens subject to preliminary strain by 1, 3, 6, 16 and 23% and subsequent tests of stress corrosion in magnesium chloride solution at 150 deg C 140 MPa has been carried out. Analysis of test results has shown that microplastic strain is distributed over a specimen nonuniformly and is accompanied with the slip bands formation which are sources of corrosion crack origination and development. 08Kh18N10T steel manifests the highest trend to stress corrosion under 1% microplastic strain

Corrosion resistance of heat exchange equipment in hydrotreating Orenburg Condensate

International Nuclear Information System (INIS)

Teslya, B.M.; Burlov, V.V.; Parputs, I.V.; Parputs, T.P.

1986-01-01

The authors study the corrosion resistance of materials of construction and select appropriate materials for the fabrication of heat exchange equipment that will be serviceable under hydrotreating conditions. This paper discusses the Orenburg condensate hydrotreating unit which has been shut down repeatedly for repair because of corrosion damage to components of heat exchangers in the reactor section: tube bundles (08Kh18N10T steel), corrugated compensators (12Kh18N10T steel), and pins of the floating heads (37Kh13N8G8MFB steel). The authors recommend that the tube bundles and the compensators in heat exchangers in the reaction section should be fabricated of 08Kh21N6M2T or 10Kh17N13M2T steel. The pins have been replaced by new pins made of 10Kh17N13 X M2T steel, increasing the service life from 6-12 months to 2 years

Effect of Heat Treatment on the Structure and Properties of Die Steel 70Kh3G2FTR

Science.gov (United States)

Krylova, S. E.; Kletsova, O. A.; Gryzunov, V. I.; Fot, A. P.; Tavtilov, I. Sh.

2018-01-01

The effect of heat treatment parameters on the properties and structural and phase composition of a promising die steel 70Kh3G2FTR for hot deformation is studied. The temperature-and-stress state of a hammer die under a heat treatment is simulated.

Effect of heat treatment and plastic deformation on the structure and the mechanical properties of nitrogen-bearing 04N9Kh2A steel

Science.gov (United States)

Blinov, V. M.; Bannykh, O. A.; Lukin, E. I.; Kostina, M. V.; Blinov, E. V.

2014-11-01

The effect of the conditions of heat treatment and plastic deformation on the structure and the mechanical properties of low-carbon martensitic nickel steel (9 wt % Ni) with an overequilibrium nitrogen content is studied. The limiting strain to failure of 04N9Kh2A steel is found to be 40% at a rolling temperature of 20°C and 80% at a rolling temperature of 900°C. Significant strengthening of the steel (σ0.2 = 1089 MPa) is obtained after rolling at a reduction of 40% at 20°C. The start and final temperatures of the α → γ transformation on heating and those of the γ → α transformation on cooling are determined by dilatometry. The specific features of the formation of the steel structure have been revealed as functions of the annealing and tempering temperatures. Electron-microscopic studies show that, after quenching from 850°C and tempering at 600°C for 1 h, the structure contains packet martensite with thin interlayers of retained austenite between martensite crystals. The strength of the nitrogen-bearing 04N9Kh2A steel after quenching from 850 and 900°C, cooling in water, and subsequent tempering at 500°C for 1 h is significantly higher than that of carboncontaining 0H9 steel used in cryogenic engineering.

Preliminary heat treatment of 4KhM2Fch die steel

International Nuclear Information System (INIS)

Leonidov, V.M.; Berezkin, Y.A.; Nikitenko, E.V.

1986-01-01

To improve the machinability and preparation of the structure for hardening, die steels are given a preliminary treatment which provides a reduction in hardness as a result of separation in the structure of the carbide and ferrite phases, coagulation of the carbides, and acquisition by them of a granular form and also the obtaining of fine grains and a uniform distribution of the structural constituents. The microstructure was evaluated after etching in 4% nital on an MIM-8M microscope. The 4KhM2Fch steel was given a preliminary heat treatment of normalize and anneal. It was concluded that for 4KhM2Fch steel a preliminary heat treatment of normalizing from 950 0 C with a hold of 1.5-2 h, annealing at 750-760 0 C with a hold of 2-3 h, cooling to the isothermal temperature of 670-680 0 C with a hold of 3-4 h, and further air cooling is recommended. The structure after such a heat is granular pearlite with a rating 1-2 and a hardness of 220-250 HB

Structural changes in surface layer of steel 08Kh18N10T during machining

International Nuclear Information System (INIS)

Palenik, J.; Vodarek, V.

1989-01-01

The results are reported of a study of the surface layer of steel 08Kh18N10T affected by machining. Structural changes were studied caused by finish turning and by additional roller burnishing. Multiple deformation bands were observed to occur under the given cutting conditions; they mainly consisted of deformation doublets and only in isolated cases of ε-martensite. The presence of α'-martensite was not shown in the specimen surface layer following finish turning. The deformation shear bands in the roller-burnished specimen consisted of both ε-martensite and of deformation doublets. The amount of ε-martensite in the structure was significantly higher than in the specimen worked by turning. Local presence of α'-martensite formations was observed inside the deformation bands. It thus follows that roller burnishing is unsuitable as part of the manufacture of components from steel 08Kh18N10T. (J.B.). 5 figs., 1 tab., 9 refs

Effect of heat treatment regime on structural lamination in ferritic-austenitic steels

International Nuclear Information System (INIS)

Sizov, R.A.; Zakharova, M.I.; Novikov, I.I.; Bannykh, O.A.

1983-01-01

The effect of preliminary thermal treatment on lamination and viscosity of EhP-53 and KO-3 steels after durable aging at the temperature of 350 is studied. It is shown that preliminary heat treatment considerably affects lamination processes in the result of aging of 0Kh18G8N2T steel. The lowest rate of lamination and higher impact strength after aging at 350 deg C for 4500 hours corresponds to the following heat treatment: 10 hour aging at 650 deg C with cooling in the air, then quenching in water from 950 deg C after aging for 30 min and the following tempering (650 deg C, 5 hours). Unlike the 0Kh18G8N2T steel, lamination parameters of steel 0Kh22N6T practically do not change after the application of heat treatment. Nevertherless, taking into account results of impact strength, it is advisable to have thermal treatment according to the regime: quenching in water at 950 deg C after aging for 30 min

Effects of Mo Content on Microstructure and Mechanical Property of PH13-8Mo Martensitic Precipitation-Hardened Stainless Steel

Science.gov (United States)

Yubing, Pei; Tianjian, Wang; Zhenhuan, Gao; Hua, Fan; Gongxian, Yang

This paper introduces the effects of Mo content on microstructure and mechanical property of PH13-8Mo martensitic precipitation-hardened stainless steel which is used for LP last stage blade in steam turbine. Thermodynamic software Thermo-Calc has been used to calculate precipitation temperature and the mass fraction of precipitated phases in PH13-8Mo steel with different Mo content. The result shows that when the mass of Mo is below 0.6wt.%, chi-phase mu-phase and sigma-phase could disappear. The microstructure and mechanical property of high Mo PH13-8Mo (Mo=0.57wt.%) and low Mo PH13-8Mo (Mo=2.15wt.%)have been investigated in different heat treatments. The investigations reveal that austenitizing temperature decrease with the reduce of Mo content, so the optimum solution temperature for low Mo PH13-8Mo is lower than that for high Mo PH13-8Mo.The influence of solution temperature on grain size is weakened with the increase of Mo content, Mo rich carbides could retard coarsening of grain. An enormous amount of nano-size uniformly distributed β-NiAl particles are found in both kinds of steels using transmission electron microscopy, they are the most important strengthening phase in PH13-8Mo.

Nitrogen effect on the tendency of Cr-Ni-MN steels to delayed fracture under stress and hydrogen effects

International Nuclear Information System (INIS)

Suvorova, S.O.; Fillipov, G.A.

1996-01-01

Austenitic steels types 03Kh17N16G10AM5, 03Kh6N12G10AM5 and 07Kh13AG20 with various nitrogen contents were studied for their tendency to delayed fracture using mechanical tests, fractography and X ray diffraction analysis. The steel type 07Kh13G20 exhibited the highest strength in the initial state but showed an increase tendency to delayed fracture after hydrogenation. It is underlined that nitrogen additions essentially intensify the tendency of cold worked steels to delayed fracture. This fact should be taken into account when using nitrogen-containing Cr-Ni-Mn steels under severe operational conditions. 4 refs., 2 tabs

Effect of silicon on the structure, tribological behaviour, and mechanical properties of nitrogen-containing chromium-manganese austenitic steels

International Nuclear Information System (INIS)

Korshunov, L.G.; Chernenko, N.L.; Gojkhenberg, Yu.N.

2003-01-01

The effect of silicon in quantity of 3.5-4.5 mass. % on tribological behaviour is studied for nitrogen-bearing (0.20-0.52 mass. % of nitrogen) chromium-manganese austenitic steels (10Kh15G23S4A0.20, 10Kh16G17N3S4A0.30, 10Kh19G20NS4A0.50, 12Kh19G19NS2A0.50, 10Kh18G19A0.50, 08Kh16G8N10S4A0.18). Mechanical properties and corrosion resistance of the steels are determined. Using metallographic, x-ray diffraction and electron microscopical methods a study is made into structural transformations running in the steels considered under friction and static tension. It is shown that additional silicon alloying of nitrogen-bearing chromium-manganese austenitic steels results in an essential increase of adhesion wear resistance of the materials on retention of low friction coefficient (f=0.25-0.33). A strong silicon effect on steel tribological behaviour is related with planar slip activation and with an increase of austenite strength and heat resistance [ru

Peculiarities of welding procedure for the 05Kh12K14N5M5T-VD maraging stainless steel with strength higher 1500 MPa

International Nuclear Information System (INIS)

Pustovit, A.I.

1980-01-01

The effect of welding procedure of 05Kh12K14N5M5T-VD stainless steel on the properties of its welded joints is investigated. A new procedure of welding for pressure vessels made of this steel using Sv-03Kh15K14N5M3T-EL welding wire is suggested [ru

Neutron diffraction study of a nitrogen martensitic steel 0Kh16N4AB under load

Czech Academy of Sciences Publication Activity Database

Sumin, V. V.; Papushkin, I.V.; Bannykh, O.A.; Blinov, V.M.; Lukáš, Petr

2008-01-01

Roč. 105, č. 1 (2008), s. 88-91 ISSN 0031-918X Institutional research plan: CEZ:AV0Z10480505 Keywords : steel 0Kh16N4AB * neutron diffraction * FSD Subject RIV: BG - Nuclear, Atomic and Molecular Physics , Colliders Impact factor: 0.412, year: 2008

Study of surface layer on 08Kh15N5D2T steel

International Nuclear Information System (INIS)

Tyurin, A.G.; Povolotskij, V.D.; Zhivotovskij, Eh.A.; Berg, B.N.

1986-01-01

08Kh15N5D2T steel phase composition is investigated. Its surface layer was determined by X-ray diffraction analysis method. It is shown, that a subscale appears to be the reason for corrosion of products, made of EhP410 steel. Under the existing smelling technology the carbon content in it is ≥ 0.05%. Therefore to avoid the metal surface depletion with chromium, one must provide for titanium relation to carbon of not less than 4.5 and carry out the rolled product thermal treatment in a protective atmosphere; otherwise, the technology must include not only the removal of scale from steel but the metal subscale layer as well

The effect of laser treatment on the wear resistance of steel in corrosive media

International Nuclear Information System (INIS)

Plyatsko, G.V.; Porter, A.I.; Prejs, G.A.; Mojsa, M.I.

1975-01-01

The corrosion mechanical wearing properties of steel 45 treated with a laser beam (H 100 =7800 Mn/sq.m) under friction with nitrated steel 40KhNMA (HV=7000 Mn/sq.m), chrome cast iron Kh15M (hardened and low-temperature tempered, modified), perlite cast iron and bronze are studied. The aqueous buffers with pH=6 and 11 are used as a corrosion active media. In a weakly acid medium the most intensive wearing of steel 40KhNMA is observed at P=8 Mn/sq.m. Its wearing reduces due to increase of pressure to 12 Mn/sq.m. Extent of steel 45 wearing increases with pressure increase from 8 to 12 Mn/sg.m. Friction coefficient of this pair changes by jumps at an increase of normal pressure and its variation range is smaller than that observed in an alkaline medium. The maximum value of friction coefficient is shifted to the higher pressure. The wearing of cast iron Kh15M-steel 45 pair has an alternative pattern. In an alkaline medium the cast iron wearing intensity shows a linear increase with the normal contact pressure but that of the steel changes jumpwise attaining extreme at 8 and 12 Mn/sq.m. In a weak acid medium the intensity of grasping and graphitization at the friction surface of cast iron Kh15M-steel 45 pair is higher than that in the alkaline medium. Experiments demonstrate an effectiveness of the laser beam treatment of steel 45 for its friction in the alkaline medium with nitrated steel 40KhNMA and with hardened low-temperature tempered cast iron 45 under friction contact pressure as high as 8 Mn/sq.m, and in acid medium at 12 and 8 Mn/sq.m respectively. The laser treatment provides high corrosion-mechanical stability of steel 45 and the counterbodies described, as well as the low friction coefficient of these pairs

SCC growth behavior of cast stainless steels in high-temperature water. Influences of corrosion potential, steel type, thermal aging and cold-work

International Nuclear Information System (INIS)

Yamada, Takuyo; Terachi, Takumi; Miyamoto, Tomoki; Arioka, Koji

2011-01-01

Recent studies on crack growth rate (CGR) measurement in oxygenated high-temperature pure water conditions, such as normal water chemistry (NWC) in BWRs, using compact tension (CT) type specimens have shown that stainless steel weld metal are susceptible to stress corrosion cracking (SCC). On the other hand, the authors reported that no significant SCC growth was observed on stainless steel weld metals in PWR primary water at temperatures from 250degC to 340degC. Cast austenitic stainless steels are widely used in light water reactors, and there is a similarity between welded and cast stainless steels in terms of the microstructure of the ferrite/austenite duplex structure. However, there are a few reports giving CGR data on cast stainless steels in the BWRs and PWRs. The principal purpose of this study was to examine the SCC growth behavior of cast stainless steels in simulated PWR primary water. A second objective was to examine the effects on SCC growth in hydrogenated and oxygenated water environments at 320degC of: (1) corrosion potential; (2) steels type (Mo in alloy); (3) thermal-aging (up to 400degC x 40 kh); and (4) cold-working (10%). The results were as follows: (1) No significant SCC growth was observed on all types of cast stainless steels: aged (400degC x 40 kh) of SCS14A and SCS13A and 10% cold-working, in hydrogenated (low-potential) water at 320degC. (2) Aging at 400degC x 40 kh SCS14A (10%CW) markedly accelerated the SCC growth of cast material in high-potential water at 320degC, but no significant SCC growth was observed in the hydrogenated water, even after long-term thermal aging (400degC x 40 kh). (3) Thus, cast stainless steels have excellent SCC resistance in PWR primary water. (4) On the other hand, significant SCC growth was observed on all types of cast stainless steels: 10%CW SCS14A and SCS13A, in 8 ppm-oxygenated (high-potential) water at 320degC. (5) No large difference in SCC growth was observed between SCS14A (Mo) and SCS13A. (6) No

Effect of boron control of environment on corrosion and resistance to low-cycle corrosion fatigue in structural steels

International Nuclear Information System (INIS)

Babej, Yu.I.; Zhitkov, V.V.; Zvezdin, Yu.I.; Liskevich, I.Yu.; Nazarov, A.A.

1982-01-01

Tests of the specimens on total, contact and crevice corrosion, corrosion cracking and low-cycle fatigue are conducted for determination of corrosion and corrosion-fatigue characteristics in the 15Kh3NMFA, 10N3MFA, 10Kh16N4B, 05Kh13N6M2 structural steels, used in energetics. The environment is subjected to boron control and contacting with atmosphere for simulation of stop and operation modes of the facility. The experiments are carried out in the distilled water with 12g/l H 3 BO 3 and 10 mg/l Cl' at 25, 60, 100 deg C under contacting with atmosphere. It is established, that the pearlitic steels 15Kh3NMFA, 10N3MFA, as well as transition and martensitic 05Kh13N6M2 and 10Kh16N4B steels are highly stable to total, crevice and contact corrosion at the high parameters of aqueous boron-containing medium. Steel resistance to low-cycle fracture decreases slightly under the conditions similar to the operation ones, in the water with 12 g/l H 3 BO 3 . Durability of the pearlitic steels at the simulation of stop conditions decreases more noticeably, crack formation as a rule, initiating from corrosion spots

Protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

Energy Technology Data Exchange (ETDEWEB)

Mindyuk, A K; Svist, E I; Savitskaya, O P; Goyan, E B; Gopanenko, A N [AN Ukrainskoj SSR, Lvov. Fiziko-Mekhanicheskij Inst.

1975-01-01

The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves.

Effect of nonmetallic inclusions on anisotropy of ductility in 35KhN3MFA steel forgings

International Nuclear Information System (INIS)

Shtremel', M.A.; Yavojskij, V.I.; Volkov, V.A.; Chursin, G.M.; Chukhlov, V.I.; Fetisov, G.I.; Mochalin, N.K.; Smol'yaninov, L.V.

1980-01-01

Characteristics of nonmetaltic inclusions and anizotropy of ductility and of impuct strength of forgings of the 35KhN3MFA steel are compared at different variants of melting and outer-furnace treatment. It is shown that method of melting rugulates anisotropy of ductility primarily through deformability of large inclusions during forging. Deformability of inclusions considerably changes due to introduction of silicocalcium in iron mold [ru

On choice of tempered steels

International Nuclear Information System (INIS)

Govorov, A.A.; Pan'shin, I.F.; Rakhmanov, V.I.

1978-01-01

For the purpose of developing a graphical method for choosing structural steels, a change in the propagation work of a crack and in the critical temperature of brittleness of 40, 40Kh, 40KhN, and 40KhNM steels, was examined depending on the hardness after hardening and tempering. A diagram enabling to choose the grade of steel for making an article of known dimensions according to the preset values of its mechanical properties has been plotted. The developed selection scheme takes into account the hardenability of steels and the influence of the hardness after thermal treatment on the cold-shortness of steel

Pipes out of the chromium-molybdenum 12Kh2M1 steel intended for power units

International Nuclear Information System (INIS)

Saf'yanov, A.V.; Plyatskovskij, O.A.; Khokhlov-Nekrasov, O.G.; Palatnikova, E.S.; Karpenko, N.P.

1977-01-01

Vanadiumless steel 12Kh2M1 (2.25%Cr, 1%Mo) known to be applied abroad has been used for production of 325x60 mm tubes. The technology involves heating of the blanks to 1270-1300 deg C, their piercing in a double-roller mill, rolling on a pilger mill 8-16'' in thick wall caliber rolls, thermal treatment (normalizing at 930-960 deg C for 1 hour and tempering at 730+-10 deg C for 4 hours and etching (12-22% H 2 SO 4 and up to 143 g/l FeSO 4 ) for 3-4 hours at 55-65 deg C. Good technological properties of the steel and its capacity of working at 540-580 deg C are confirmed. Vanadium alloying of boiler steels does not provide for essential improvement of oxydation resistance and long term strength, but decreases the workability and enhances scatter of working parameters on account of minor variations of chemical composition

The effect of alloying and treatment on martensite transformation during deformation in Fe-Cr-Mn steels with unstable austenite

International Nuclear Information System (INIS)

Malinov, L.S.; Konop, V.I.; Sokolov, K.N.

1977-01-01

The effect is studied of alloying with chromium (6-10%), silicon (1-2%), molybdenum (1-3%), and copper (2%), the heat treatment conditions, and the deformation conditions, or the martensitic transformation and mechanical properties of Fe-Cr-Mn steels of the transitional class based on 0G8AM2S. It is shown that appropriate alloying and treatment, taking into account the degree of stability of the austenite, can ensure a complex of high mechanical properties of the steels investigated. For instance, the treatment of steel 0Kh10AG8MD2S by the technique: hardening+ 40% deformation at 400 deg C + 10% deformation at room temperature has yielded the following mechanical properties: sigmasub(B)=150 kgf/mm 2 , sigmasub(T)=110 kgf/mm 2 , sigma=18%, psi=32%

Estimation of structural strength of 38KhN3MFA steel, melted using different methods

International Nuclear Information System (INIS)

Kudrya, A.V.; Mochalov, B.V.; Fadeev, Yu.I.

1982-01-01

Quantity of steel melted by different methods using criteria of fracture mechanics is evaluated. Three technological variants of the 38KhN3MFA steel melting: acid Martin steel prepared by the duplex-process (melt 1); the main Martin steel melting with deoxidation and alloying in a ladle by liquid alloy and treatment with synthetic slag with argon purging after production (melt 2) and its electroslag remelt - ESP process (melt 3) are investigated. The analysis of the investigated melts has revealed that crack resistances of the acid Martin steel is higher than that of other melts at practically similar standard mechanical properties with 0.35 probability at 0.05 significance level in the low-tempered state; in the tempered state the best crack resistance is observed in the ESP main Martin steel. Metal of the main Martin melting has lower crack resistance as compared with other meltings at both strength levels. The results of the work point out the necessity of applying the criteria of fracture mechanics for obtaining an objective evaluation of the steel quality

Application of experiment planning during investigation of cementation process in solid carburizers

International Nuclear Information System (INIS)

Lisenkov, A.N.; Denisov, V.M.; Prigozhina, E.L.

1981-01-01

A mathematical model of cementation process in solid carburizirs is obtained, the most effective contents of carburizers are chosen. Specimens are produced out of St20, 12KhN3A, 40Kh13, KhVG steels. It is shown that specimens of St20 and 12KhN3A steels have the higher depth of cementated layer, specimens made of 40Kh13 and KhVG steels-the lower depth. It is shown that the quality of cementated layer structure at recommended regimes improved, cementated layer depth for low-carbon steels changed a little and for tool steels increased infficiently: for KhVG steel in 2-3 times for 40Kh13 steel in 1.5-2.5 times

On the protective effect of KhOSP-10 inhibitor during corrosion, hydrogenadsorption and corrosion cracking of a steel in sulfuric acid

International Nuclear Information System (INIS)

Mindyuk, A.K.; Svist, E.I.; Savitskaya, O.P.; Goyan, E.B.; Gopanenko, A.N.

1975-01-01

The protective propeties of inhibitor KhOSP-10 in the time of corrosion and corrosive cracking of steel 40Kh are higher then those of inhibitors KPI-1, KI-1, I-I-V etc. Its ability to reduce steel hydrogenation is the same as in the case of KPI-1 inhibitor i.e. below that of KI-1. HCl additives enhance the efficiency of inhibitors KPI-1, KI-1, I-1-V etc. up to the protective ability of KhOSP-10. Kinetics of the electrode processes was estimated from polarization curves

Ductile fracture of two-phase welds under 77K. [Steel-EhP810, steel-EhP666, steel-08Kh18N10T, steel-EhP659-VI, steel-chP810

Energy Technology Data Exchange (ETDEWEB)

Yushchenko, K.A.; Voronin, S.A.; Pustovit, A.I.; Shavel' , A.V.

The effect of the type of welding and fillers on crack resistance of welded joints high-strength steel EhP810 and its various compounds with steels EhP666, 08Kh18N10T has been studied. For the welding of steel EhP810 with steels EhP810, EhP666, 08Kh18N10T electron-beam, automatic, argon tungsten arc with non-consumable electrode with various fillers, as well as argon metal-arc welding with consumable electrode, were used. It is shown, that for a joint, made by electron-beam welding, parameters sigmasub(u), Ksub(IcJ), KCV are higher than for a joint of a similar phase structure made using filler wire EhP659-VI. It is explained by the fact, that during electron-beam welding joint metal refining takes place, which removes gases. In welded joints of chP810 steel, having joints with austenitic structure, characteristic of crack resistance Ssub(c) increases by more than 0.2 mm in contrast to two-phase joints, which conventional yield strength at 77 K exceeds 1000 MPa. It is worth mentioning, that for other classes of steels formation of two-phase structure of joint increases welded joint resistance to brittle fracture. It is possible to obtain the required structure of joint with assigned level of resistance to brittle fracture by means of the use of different fillers, optimum and welding procedure, regulating the part of the basic metal in joint content.

Effect of partial oxygen pressure on physicochemical properties of Kh18N10T steel at isothermal oxidation

International Nuclear Information System (INIS)

Alekseev, V.N.; Oshe, E.K.; Fokin, M.N.; Bogdanova, S.V.; Loskutov, A.I.

1990-01-01

Auger-electron spectroscopy, photoelectric polarization, conductometry methods have been used to analyze chemical and defect composition of surface oxide layers, formed on stainless steel Kh18N10T in vacuum (10 -9 - 10 -2 torr) and at temperatures 593-673 K. The boundary conditions of manifestation of extermal behaviour of the dependence of the surface oxide growth rate at isothermal oxidation of this steel are determined. The relation between passivation properties of the surface oxide and the magnitude of the edge angle of the surface wetting with molten tin is revealed

Identification of G-phase in aged cast CF 8 type stainless steel

International Nuclear Information System (INIS)

Bentley, J.; Miller, M.K.; Brenner, S.S.; Spitznagel, J.A.

1985-01-01

The microstructure of as-cast and aged CF 8 type stainless steel, used for the primary coolant pipes in pressurized light-water nuclear reactors, is being studied by analytical electron microscopy (AEM) and atom probe field-ion microscopy (APFIM). The phase transformations of the ferrite (approx. 19 vol % of the duplex structure) that occur after aging at 673 K for 7500 h are described by Miller et al. The present work deals with the identification of G-phase (prototype compound Ni 16 Ti 6 Si 7 ) observed in the ferrite of aged material. 2 references, 3 figures

Stationary potentials and corrosion of metals and steels in sodium and potassium chloride eutectic melts saturated with hydrogen chloride

International Nuclear Information System (INIS)

Belov, V.N.; Ershova, T.K.; Kochergin, V.P.

1978-01-01

Stationary potentials have been measured at 850 deg C and corrosion rates found gravimetrically for a number of metals and steels in the eutectic NaCl-KCl melt saturated with HCl. Periodic shifts of the stationary potentials towards positive values have been established in the Ti-V-Cr-Fe-Ni, Cu-Zr-Nb-Mo, Ag-Ta-W-Pt systems, with the corrosion rate of metals decreasing in them. The stationary potentials are shown to shift towards positive values in the series: st.08 KP, st.3, Kh17N2, Kh22N6T, Kh13NChG9, 1Kh18N10T, Kh17N13M2T, OKh17N16M3T, Kh23N18, Kh25N16G7, Kh23N28M3D3T, with corrosive resistance in this series increasing

Metallographical procedure for detecting carburized layer in the 12Kh18N10T steel tubes

International Nuclear Information System (INIS)

Najmark, S.I.; Shmalenyuk, R.P.

1977-01-01

The various causes of the tendency to intercrystalline corrosion of stainless steel tubing were studied. 12Kh18N10T steel tube specimens were metallographically investigated to reveal the presence and depth of the carburized layer. Unlubricated specimens and specimens with the graphite-saltpeter lubrication applied on them were austenized in the temperature range from 950 to 1250 deg C and then exposed to a provoking anneal at 650 deg C for 24 h. All the lubricated specimens showed a carbide network along grain boundaries and intercrystalline cracks. The specimens treated without lubrication had no cracks. The method offered can differentiate poor tube cleaning and the undesirable effect of other processing steps on the tubes

Electron beam welding of flanges with tubular shafts of steel 40KhNMA

International Nuclear Information System (INIS)

Leskov, G.I.; Zhivaga, L.I.; Shipitsyn, B.N.; Savichev, R.V.

1975-01-01

The results are presented of elaborating the technological process for the electron beam welding of flanges with a tube of the 40KhNMA steel and of investigation into the quality of the welded joints. A welded piece has been fabricated conforming to the technology suggested observing the parameters worked-out in the following sequence: assembling the piece; pre-welding of the edges in some points; welding; high tempering; welds quality control; removal of the seam reinforcement inside of the tube and the weld root to the depth of 2 mm; quenching; tempering; welds quality control; finishing. The welds quality control consists in visual inspection, ultrasonic testing, magnetic flaw detection, as well as X-ray and metallographic analyses. The mechanical properties are studied on notched samples cut out of the welded joints. The test results have shown that the mechanical properties of the welded joints meet the requirements on the same level with the base metal

Specific features of precipitation hardening of austenitic steels with various base. 2. Kinetics and mechanism of carbide precipitation

International Nuclear Information System (INIS)

Kositsyna, I.I.; Sagaradze, V.V.; Khakimova, O.N.

1997-01-01

Electron microscopic studies were carried out to determine the kinetics and mechanisms of precipitation hardening in Fe-Mn, Fe-Mn-Cr, Fe-Cr-Mn-N, Fe-Cr-Ni and Fe-Ni base stainless steels (45G20M2F2, 50Kh16G15N6M2F2, 45Kh18N10G10M2F2, 40Kh18Ni18M2F2, 45N26M2F2). The steels were heat treated under various conditions. It is revealed that in manganese steels the particles of vanadium carbide nucleate according to homogeneous mechanism at all aging temperatures (600-750 deg C). The presence of chromium in the matrix promotes the transition to heterogeneous mechanism of carbide nucleation and growth. With nickel content increasing the plasticity of precipitation hardened steels gets better due to more intense diffusion of atoms and vacancies to grain boundaries and, hence, the widening of near-boundary zones free of carbide particles

Welding of heterogeneous 12Kh2MFSR steels with the Mn-Cr-Si-Ni system

International Nuclear Information System (INIS)

Smirnov, A.N.; Belogolov, E.I.

1978-01-01

The process of welding pipes of the 12Kh2MFSR pearlitic steels and austenitic steels of the Mn-Cr-Si-Ni system was studied. The filler materials were selected, and the working capacity of welded joints was examined in ageing and cyclic heatings. The microhardness of steels was measured, and the ultimate strength of welded joints was determined. The following has been established: the composite joints of steels of the Mn-Cr-Si-Ni system and 12Kh2MFSR steel are advisable to be welded on a coating layer welded by the EhA395/9 electrodes on the surface of a pipe of the 12Kh2MFSR pearlitic steel; this guarantees the sufficient working capacity of welded joints

Wear resistance and structural changes in nitrogen-containing high-chromium martensitic steels under conditions of abrasive wear and sliding friction

International Nuclear Information System (INIS)

Makarov, A.V.; Korshunov, L.G.; Schastlivtsev, V.M.; Chernenko, N.L.

1998-01-01

Martensitic nitrogen-containing steels Kh17N2A0.14, Kh13A0.14, Kh14G4A0.22 as well as steel 20Kh13 were studied for their wear resistance under conditions of friction and abrasion. Metallography, X ray diffraction analysis and electron microscopy were used to investigate the structural changes taking place in a thin surface layer on wearing. It is shown that an increase of nitrogen content of 0.14 to 0.22% promotes an enhancement of steel resistance to abrasive and adhesive wear, especially after tempering in the range of 500-550 deg C. Typically, the nitrogen-containing steels exhibit lower resistance to various types of wear in comparison with the steels with high-carbon martensite due to their lower deformability under conditions of friction loading

Hardening and stress relaxation during repeated heating of 15Kh2MFA and 15Kh2NMFA steels welded joints

International Nuclear Information System (INIS)

Zubchenko, A.S.; Suslova, E.A.

1986-01-01

Results of investigation of temperature-time conditions of hardening of welded joints of 15Kh2MFA and 15Kh2NMFA steels and their relaxation resistance, effect of metal structure of imitated heat affected zone (HAZ) on intensity of precipitation hardening at repeated heating are presented as well as the results of the process of relaxation of residual stresses at welded joints samples heating carried out by automatic welding under the flux with the use of adding materials and technology of manufacturing of vessels of WWER-440 and WWER-1000 reactors. Peculiarities of the hardening at repeated heating of the HAZ metal imitated at these steels. Precipitation hardening of overheated 15Kh2MFA steel is connected with precipitations at repeated heating of carbides of the M 7 C 3 , M 3 C and VC type. Stress relaxation in welded joints runs more intensively at the initial stage of repeated heating, i.e. during the same period of the process of dispersed carbide precipitations

Modeling the wire-EDM process parameters for EN-8 carbon steel ...

African Journals Online (AJOL)

Modeling the wire-EDM process parameters for EN-8 carbon steel using .... The neural networks has been developed with the help of MATLAB 8.1 (R13) package .... Now, Simulation and Prediction will be performed using the trained network.

Effect of operational conditions of electroerosion machining on the surface microgeometry parameters of steels and alloys

International Nuclear Information System (INIS)

Foteev, N.K.

1976-01-01

Studies the influence of pulse duration and a series of operating conditions of a ShGI-40-440 spark-machining generator on changes in the basic surface microgeometry characteristics of components of stainless steel 1Kh18N10T, steel St 45 and hard alloy T14K8. The microgeometry characteristics of spark-machined surfaces differ significantly from the corresponding characteristics of surfaces machined by cutting and vibro-rolling

Features of argon-arc welding of aluminium alloy AD1 to stainless steel 12Kh18N10T

International Nuclear Information System (INIS)

Sadov, I.I.

1982-01-01

Welding of pipes made of the 12Kh18N10T stainless steel and the AD1 aluminium alloy is proposed to perform using one-sided aluminizing. It is recommended to use shields in order to protect internal and external surfaces of pipes, aluminizing of which is impossible. It is shown that developed technological process for welded joints made of aluminium and stainless steel for cryogenic apparatus permits to create light-duty cryostat assembly using aluminium alloys instead of copper alloys, to increase reliability of apparatus (usage of welded joints instead of soldered ones), and to improve labour conditions

Heat treatment of investment cast PH 13-8 Mo stainless steel: Part II. Isothermal aging kinetics

Science.gov (United States)

Robino, C. V.; Cieslak, M. J.; Hochanadel, P. W.; Edwards, G. R.

1994-04-01

The hardening response of investment cast PH 13-8 Mo stainless steel has been evaluated by hardness measurements following aging in the temperature range normally specified for this alloy (510 °C to 593 °C). A new relationship between fraction transformed and hardness was developed, and analysis of the data in terms of the kinetics of precipitation, in a manner similar to that frequently applied to other precipitation-hardenable martensitic steels, yielded low time exponents and a low value for the apparent activation energy. The values of the time exponents were 0.49, 0.37, 0.56, and 0.53 at 510 °C, 538 °C, 566 °C, and 593 °C, respectively, and that for the apparent activation energy was 139 kJ/mole. As has been proposed for other maraging type steels, these estimates suggest that Β-NiAl precipitates along or near dislocations and that growth of the precipitates is dominated by dislocation pipe diffusion. However, these predictions were neither supported nor refuted by transmission electron microscopy (TEM) because of difficulties in imaging the Β-NiAl precipitates at the aging times and temperatures used. Further, analysis of the data using the formalism of Wert and Zener for the growth of precipitates with interfering diffusion fields indicated that the estimates of fraction transformed from hardness data are not fully appropriate for maraging type steels. Consideration of the nature of the Avrami analysis and the electron microscopy results suggests that other phenomena, including dislocation recovery and reversion of martensite to austenite, occur at rates sufficient to convolute the Avrami analysis. It is further suggested that these results cast doubt on the fundamental implications of previous analyses of precipitation kinetics in age-hardening martensitic steels. Although the Avrami analysis was found not to provide a tenable description of the precipitation kinetics, it does provide a reasonable methodology for portrayal of the hardening response

Additional materials for welding of the EP99 heat resisting alloy with the EI868 alloy and 12Kh18N9T steel

International Nuclear Information System (INIS)

Sorokin, L.I.; Filippova, S.P.; Petrova, L.A.

1978-01-01

Presented are the results of the studies aimed at selecting an additive material for argon-arc welding process involving heat-resistant nickel EP99 alloy to be welded to the EI868 alloy and 12Kh18N9T steel. As the additive material use was made of wire made of nickel-chromium alloys and covered electrodes made of the EP367 alloy with additions of tungsten. It has been established that in order to improve the resistance of metal to hot-crack formation during argon arc welding of the EP99 alloy with the EI868 alloy, it is advisable to use an additive material of the EP533 alloy, and while welding the same alloy with the 12Kh18N9T steel, filler wire of the EP367 alloy is recommended

16-8-2 weld metal design data for 316L(N) steel

Energy Technology Data Exchange (ETDEWEB)

Tavassoli, A.-A.F. [Commissariat a l' Energie Atomique, CEA/Saclay, 91191 Gif sur Yvette (France)], E-mail: tavassoli@cea.fr

2008-12-15

ITER materials properties documentation is extended to weld metals used for welding Type 316L(N) steel, i.e. the structural material retained for manufacturing ITER major components, such as the vacuum vessel. The data presented here are mainly for the Type 16-8-2 and complete those already reported for the low temperature (Type 316L) and the high temperature (Type 19-12-2) filler metals. The weld metal properties data for Type 16-8-2 filler metal and its joints are collected, sorted and analysed according to the French design and construction rules for nuclear components (RCC-MR). Particular attention is paid to the type of weld metal (e.g. wire for TIG, covered electrode for manual arc, flux wire for automatic welding), as well as, to the weld geometry and welding position. Design allowables are derived from validated data for each category of weld and compared with those of the base metal. In most cases, the analyses performed are extended beyond the conventional analyses required for codes to cover specific needs of ITER. These include effects of exposures to high temperature cycles during component fabrication, e.g. HIPing and low dose neutron irradiation at low and medium temperatures. The ITER Materials Properties Handbook (MPH) is, here, enriched with files for physical and mechanical properties of Type 16-8-2 weld metal. These files, combined with the codification and inspection files, are part of the documentation required for ITER licensing needs. They show that all three weld-metals satisfy the code requirements, provided compositions and types of welds used correspond to those specified in RCC-MR.

Influence of structure and properties of tubular billets of the 12 Kh 18N10T steel on deformability of tubes at cold-rolling mills

International Nuclear Information System (INIS)

Vil'yams, O.S.; Bol'shova, N.M.; Olejnik, O.V.; Velikotnaya, E.S.

1979-01-01

Metallographic analysis of the defects of the ''oblique cracks'' type on the surface of hot-rolled tubes of the 12Kh18N10T steel has been carried out. Recommended is the complex of mechanical properties and the structure factors (grain size) of conversion hot-rolled tubes, providing the combination of ductility and high rapture strength during rolling at pilger mills. At a grain size not coarser than number 5, a billet must have σsub(T) 5 >=40 %. Hot-rolled coarse-grained billet is not recommended for warm rolng because of high strain hardening

Effect of agressive medium movement of local corrosion of the steel - 12Kh18N10T

International Nuclear Information System (INIS)

Makartsev, V.V.; Pakhomov, V.S.; Abramova, I.M.

1980-01-01

The effect of agressive medium movement on the formation of pitting corrosion of the 12Kh18N10T stainless steel in the acidic chloride-nitrate solution at room temperature is studied. It is established that the agressive medium movement hinders the formation of pitting corrosion at potentials more negative than +0.4 V and practically does not affect it at more positive potentials. The investigations have been carried out on a disc electrode rotating at a speed from 0 to 2000 rot./min

Effect of partial oxygen pressure on physicochemical properties of Kh18N10T steel at isothermal oxidation. Vliyanie partsial'nogo davleniya kisloroda na fiziko-khimicheskie svojstva poverkhnosti stali Kh18N10T pri izotermicheskom okislenii

Energy Technology Data Exchange (ETDEWEB)

Alekseev, V N; Oshe, E K; Fokin, M N; Bogdanova, S V; Loskutov, A I [AN SSSR, Moscow (USSR). Inst. Fizicheskoj Khimii

1990-10-01

Auger-electron spectroscopy, photoelectric polarization, conductometry methods have been used to analyze chemical and defect composition of surface oxide layers, formed on stainless steel Kh18N10T in vacuum (10{sup -9} - 10{sup -2} torr) and at temperatures 593-673 K. The boundary conditions of manifestation of extermal behaviour of the dependence of the surface oxide growth rate at isothermal oxidation of this steel are determined. The relation between passivation properties of the surface oxide and the magnitude of the edge angle of the surface wetting with molten tin is revealed.

The effect of chromium diffusion redistribution on wear resistance of carburized 3Kh13 steel

International Nuclear Information System (INIS)

Shcherbedinskij, G.V.; Shumakov, A.I.; Zemskij, S.V.; Pereverzev, V.M.

1977-01-01

The redistribution of chromium in steel 3Kh13 on carburization in a high-activity carburizer and the wear-resistance of the steel have been investigated. Surface layers with an increased chromium concentration show the highest wear-resistance. The chromium content in the surface layer increases due to its diffusion from the interior. The distribution of carbon and chromium in the carburized layers has been studied with the aid of the radioactive isotope 14 C by the method of layer-by-layer spectral analysis on a vacuum quantometer, layer-by-layer chemical and X-ray structure analysis. The composition of the carbides has been determined by physicochemical analysis. It has been established that the carburized layer can be divided into four zones with respect to its phase composition: first zone - hematite and spinal with 0.5-2.0% C; second zone - solid carbides (Fe,Cr) 7 C 3 ; up to 5% C; third zone - globular carbides in a troostite matrix (Cr,Fe) 7 C 3 and Cr 23 C 6 ; up to 3.5% C; fourth, transitional, zone - troostite carbide mixture Cr 23 C 6 ; up to 1% C. The chromium diffusion in the carburized layer is faster than in the initial austenite. The chromium counterdiffusion is due to the development of a zone of solid carbides M 7 C 3

Development and industrial mastering hot rolling procedure for low-ductile steels and alloys

International Nuclear Information System (INIS)

Degterenko, V.K.; Sokolov, V.A.

1980-01-01

The technique for the development of the sheet hot rolling procedure for low-ductile steels and alloys (0Kh17N14M2, 12Kh21N5T, 20Kh25N20C2,40Kh13, 36NKhTYu etc.) is proposed, using plastometer which permits to obtain the data on the deformation resistance in the wide range of temperatures (800-1300 deg C), of deformation degrees (0.1-0.3) and deformation rates (0.001-300 c -1 ). With the help of the plastometric data processed on the computer the calculation of the rolling regimes for the sheet with improved surface quality is carried out at the more uniform loading on the mill stands

Hot working effect on austenite transformations in structural steel in continuous cooling

International Nuclear Information System (INIS)

Zajmovskij, V.A.; Kisteh, N.V.; Samedov, O.V.

1979-01-01

Austenite transformations in 40, 40Kh, 40KhN and 40KhNMA steels under hot working at 900 deg C with 20% reduction degree and continuous cooling with 1,7-16 0 /s are investigated. Changing of cooling rate in various ways affects the temperature range of austenite transformation in pearlite and bainite regions. Regulating the cooling rate after hot working one can essentially change the impact strength and steel ductility as a result of high temperature thermomechanical treatment effect

Structural inheritance in cast 30KhGNM-type steel

International Nuclear Information System (INIS)

Sadovskij, V.D.; Bershtejn, L.I.; Mel'nikova, A.A.; Polyakova, A.M.; Schastlivtsev, V.M.

1980-01-01

Structural inheritance in the cast 30KhGNM-type steel depending on the heating rate and the temperature of preliminary tempering is investigated. When eating the cast steel with a beinite structure at the rate of 1-150 deg/min, the restoration of austenite grain and the following recrystallization due to the phase cold work, are observed. Slow heating from room temperature or preliminary tempering hinder grain restoration during heating. A non-monotonous effect of tempering temperature on the structural inheritance is established which can be connected with the kinetics of decomposition of residual austenite in steel

Synthesis and evaluation of novel multimeric neurotensin(8-13) analogs.

Science.gov (United States)

Hultsch, Christina; Pawelke, Beate; Bergmann, Ralf; Wuest, Frank

2006-09-01

Neurotensin(8-13) is a hexapeptide with subnanomolar affinity to the neurotensin receptor 1 which is expressed with high incidence in several human tumor entities. Thus, radiolabeled neurotensin(8-13) might be used for tumor targeting. However, its application is limited by insufficient metabolic stability. The present study aims at improving metabolic stability by the synthesis of multimeric neurotensin(8-13) derivatives rather than commonly employed chemical modifications of the peptide itself. Thus, different dimeric and tetrameric peptides carrying C- or N-terminal attached neurotensin(8-13) moieties have been synthesized and their binding affinity toward the neurotensin receptor has been determined. The results demonstrate that branched compounds containing neurotensin(8-13) attached via its C-terminus only show low receptor affinities, whilst derivatives with neurotensin(8-13) attached via the N-terminus show IC50 values in the nanomolar range. Moreover, within the multimeric neurotensin(8-13) derivatives with neurotensin(8-13) attached via the N-terminus an increasing number of branching units lead to higher binding affinities toward the neurotensin receptor.

Hot Ductility Behavior of an 8 Pct Cr Roller Steel

Science.gov (United States)

Wang, Zhenhua; Sun, Shuhua; Shi, Zhongping; Wang, Bo; Fu, Wantang

2015-04-01

The hot ductility of an 8 pct Cr roller steel was determined between 1173 K and 1473 K (900 °C and 1200 °C) at strain rates of 0.01 to 10 s-1 through tensile testing. The fracture morphology was observed using scanning electron microscopy, and the microstructure was examined through optical microscopy and transmission electron microscopy. The dependence of the hot ductility behavior on the deformation conditions, grain size, and precipitation was analyzed. The relationship between the reduction in area and the natural logarithm of the Zener-Hollomon parameter (ln Z) was found to be a second-order polynomial. When ln Z was greater than 40 s-1, the hot ductility was poor and fracture was mainly caused by incompatible deformation between the grains. When ln Z was between 32 and 40 s-1, the hot ductility was excellent and the main fracture mechanism was void linking. When ln Z was below 32 s-1, the hot ductility was poor and fracture was mainly caused by grain boundary sliding. A fine grain structure is beneficial for homogenous deformation and dynamic recrystallization, which induces better hot ductility. The effect of M7C3 carbide particles dispersed in the matrix on the hot ductility was small. The grain growth kinetics in the 8 pct Cr steel were obtained between 1373 K and 1473 K (1100 °C and 1200 °C). Finally, optimized preheating and forging procedures for 8 pct Cr steel rollers are provided.

Corrosion behaviour of stainless steels by internal friction method

International Nuclear Information System (INIS)

Postnikov, V.S.; Kovalevskij, V.I.

1987-01-01

Corrosion of austenite chromium-nickel stainless steels 12 Kh18N9, 12Kh18N9T, 12Kh18N10 and 12Kh18N10T is investigated. Wire samples 0.7...0.8 mm in diameter before tests were subjected to quenching in water from the temperature of 1050...1100 deg C and part of them - to tempering at 650 deg C for 2 h. Pitting corrosion was brought about by different concentration of iron chloride solutions (C FeCl 3 ). Total corrosion has a slight effect on the character of IF (internal friction) variation that increases without the whole test period up to the moment when mechanical strength of the sample

The Kinetics of Bainitic Transformation of Roll Steel 75Kh3MF

Science.gov (United States)

Kletsova, O. A.; Krylova, S. E.; Priymak, E. Yu.; Gryzunov, V. I.; Kamantsev, S. V.

2018-01-01

The critical points of steel 75Kh3MF and the temperature of the start of martensitic transformation are determined by a dilatometric method. The thermokinetic and isothermal diagrams of decomposition of supercooled austenite are plotted. The microstructure and microhardness of steel specimens cooled at different rates are studied. The kinetics of the occurrence of bainitic transformation in the steel is calculated using the Austin-Ricket equation.

An in vitro test to screen skin sensitizers using a stable THP-1-derived IL-8 reporter cell line, THP-G8.

Science.gov (United States)

Takahashi, Toshiya; Kimura, Yutaka; Saito, Rumiko; Nakajima, Yoshihiro; Ohmiya, Yoshihiro; Yamasaki, Kenshi; Aiba, Setsuya

2011-12-01

Several studies have suggested that interleukin (IL)-8 can serve as a biomarker for discrimination of skin sensitizers from nonsensitizers. We established a stable THP-1-derived IL-8 reporter cell line, THP-G8, which harbors SLO and SLR luciferase genes under the control of IL-8 and glyceraldehyde 3-phosphate dehydrogenase promoters, respectively. After 6 h treatment with chemicals, normalized SLO luciferase activity (nSLO-LA) was calculated by dividing SLO-LA by SLR-LA, and the fold induction of nSLO-LA (FInSLO-LA) was calculated by dividing nSLO-LA of chemically treated cells by that of nontreated cells. The nSLO-LA of THP-G8 cells increased in response to lipopolysaccharide (LPS) and several sensitizers. The FInSLO-LA in THP-G8 cells induced by LPS or sensitizers positively correlated with their induction of IL-8 messenger RNA in THP-1 cells. The nSLO-LA value of THP-G8 cells was significantly increased (FInSLO-LA ≥ 1.4) by 13 of the 15 sensitizers as well as by 5 of the 7 nonsensitizers. Interestingly, pretreatment with N-acetylcysteine suppressed the increase in FInSLO-LA induced by all sensitizers (inhibition index (II) ≤ 0.8) but did not suppress that induced by most of the nonsensitizers. We then evaluated the performance of this assay using values of FInSLO-LA ≥ 1.4 and II ≤ 0.8 in at least two of three independent experiments as the criteria of a sensitizer, which resulted in test accuracies of 82% for the 22 chemicals used and of 88% for the chemicals proposed by European Center for the Validation of Alternative Methods. This newly developed assay is a candidate replacement for animal tests of skin sensitization because of its accuracy, convenience, and high throughput performance.

Effect of Titanium on the Microstructure and Mechanical Properties of High-Carbon Martensitic Stainless Steel 8Cr13MoV

OpenAIRE

Wen-Tao Yu; Jing Li; Cheng-Bin Shi; Qin-Tian Zhu

2016-01-01

The effect of titanium on the carbides and mechanical properties of martensitic stainless steel 8Cr13MoV was studied. The results showed that TiCs not only acted as nucleation sites for δ-Fe and eutectic carbides, leading to the refinement of the microstructure, but also inhibited the formation of eutectic carbides M7C3. The addition of titanium in steel also promoted the transformation of M7C3-type to M23C6-type carbides, and consequently more carbides could be dissolved into the matrix duri...

Effect of Pulse Detonation-Plasma Technology Treatment on T8 Steel Microstructures

Science.gov (United States)

Yu, Jiuming; Zhang, Linwei; Liu, Keming; Lu, Lei; Lu, Deping; Zhou, Haitao

2017-12-01

T8 steel surfaces were treated by pulse detonation-plasma technology (PDT) at capacitance values of 600, 800, and 1000 μF, and the effects of PDT were analyzed using x-ray diffraction, scanning electron microscopy, transmission electron microscopy, electron back-scattered diffraction, and micro-hardness tester and friction wear tester. The surface of T8 steel is first smoothed out, and then, craters are formed due to the inhomogeneity of the PDT energy and targeting during PDT treatment. The initial martensite in the T8 steel surface layer changes to austenite, and Fe3N is formed due to nitriding. The thickness of the modified layer, which is composed of columnar and fine grain structures, increases with the increasing capacity. Preferential orientation occurred in the {110} 〈 001 〉 direction in the modified layer, and the number of low-angle grain boundaries increased significantly after PDT treatment. The micro-hardness and wear resistance of the T8 steel was improved by PDT treatment, even doubled after the treatment with the capacitance of 1000 μF.

1.8 cineole decreases gastric compliance in anesthetized rats 1.8 cineol diminui a complacência gástrica de ratos anestesiados

Directory of Open Access Journals (Sweden)

José Ricardo Cunha Neves

2007-02-01

continuamente por um sistema digital de aquisição de dados. RESULTADOS: Observamos diminuição do VG, o qual foi significativo aos 30, 40, 50 e 60min após o tratamento com 1.8 cineol quando comparado ao perído basal (2,0±0,1; 1,9±0,1; 1,8±0,1 e 1,7±0,1mL, vs 2,1±0,2mL. A PA apresentou queda significativa após a administração de 1.8 cineol, mantendo-se assim durante os 60min de monitoração (87,9±7,7; 87,6±7,1; 87,9±6,4; 87,8±5,7; 86,0±5,5 e 87,7±6,0mmHg, respectivamente vs 94,4±6,2; mmHg, bem como a FC (366,3±13,4; 361,7±11,5; 357,3±10,4; 353,0±10,4; 348,3±11,1 e 350,4±13,7bpm respectivamente vs 395,2±11,1bpm. Já a PVC não sofreu variações significativas durante após o tratamento. CONCLUSÃO: O 1.8 cineol diminui a complacência gástrica em ratos anestesiados além de apresentar efeitos hipotensor e bradicárdico; provavelmente por ação direta sobre a musculatura lisa gastrintestinal e vascular e modulação do sistema nervoso autônomo.

Corrosion of austenitic steels and their components in vanadium-containing chloride melts

Science.gov (United States)

Abramov, A. V.; Polovov, I. B.; Rebrin, O. I.; Lisienko, D. G.

2014-08-01

The corrosion of austenitic 12Kh18N10T, 10Kh17N13M2T, and 03Kh17N14M3 steels and their components (Cr, Fe, Ni, Mo) in NaCl-KCl-VCl2 melts with 5 wt % V at 750°C is studied. The rates and mechanisms of corrosion of the materials under these conditions are determined. The processes that occur during contact of the metals and steels with vanadium-containing chloride electrolytes are investigated.

Corrosion behavior of austenitic steels and their components in niobium-containing chloride melts

Science.gov (United States)

Abramov, A. V.; Polovov, I. B.; Rebrin, O. I.; Volkovich, V. A.; Lisienko, D. G.

2014-02-01

The mechanism of corrosion of austenitic steels 12Kh18N10T, 10Kh17N13M2T, and 03Kh17N14M3 and metals Cr, Fe, Ni, and Mo in a NaCl-KCl-NbCl n ( n = 3.5, Nb content is 5 ± 0.1 wt %) melt at 750°C is studied. The metal and steel corrosion rates under these conditions are determined. The character of material fracture and the mechanisms of material corrosion are found.

Effect of electroslag remelting on carbides in 8Cr13MoV martensitic stainless steel

Science.gov (United States)

Zhu, Qin-tian; Li, Jing; Shi, Cheng-bin; Yu, Wen-tao

2015-11-01

The effect of electroslag remelting (ESR) on carbides in 8Cr13MoV martensitic stainless steel was experimentally studied. Phases precipitated from liquid steel during solidification were calculated using the Thermo-Calc software. The carbon segregation was analyzed by original position analysis (OPA), and the carbides were analyzed by optical microscopy (OM), scanning electron microscopy (SEM), energy- dispersive X-ray spectroscopy (EDS) and X-ray diffraction (XRD). The results indicated that more uniform carbon distribution and less segregation were obtained in the case of samples subjected to the ESR process. After ESR, the amount of netty carbides decreased significantly, and the chromium and vanadium contents in the grain-boundary carbides was reduced. The total area and average size of carbides were obviously smaller after the ESR process. In the sample subjected to ESR, the morphology of carbides changed from lamellar and angular to globular or lump, whereas the types of carbides did not change; both M23C6 and M7C3 were present before and after the ESR process.

Successive carbon- and boron saturation of KhVG steel in powder mixtures

Energy Technology Data Exchange (ETDEWEB)

Alimov, Yu A; Gordienko, S I

1975-01-01

Method of successive saturation of KhVG steel with carbon and boron in powder mixtures is described. After carbonization of steel in a charcoal carburator at 930 deg C during 3 hrs a domain of equiaxial large grains is formed there the latter representing carbides of Fe/sub 3/C and (Fe, M)/sub 3/C. The increase of duration of carbonization up to 5 hrs and above results in formation of a cement grid greatly impairing the mechanical properties of the metal. Carbonization is followed by borating in powdered technical boron carbide at 900 deg C for 4 hrs which ensures formation on the sample surface of a borated layer with depth up to 65 mkm covering the carbonized zone. As followed from metallographic and x-ray structural analysis, the borated layer consists of boride needles with complex composition (Fe, Cr, Mn)B. Oil hardening of carbonized KhVG steel from 850 deg C and low-temperature tempering at 180 deg C for 1 hr results in formation in the main metal of martensite-carbide structure and, respectively, in the decrease of the microhardness gradient between the diffusion layers, as compared with borated KhVG steel. Operation tests of strengthened matrices of preforming machines under the conditions of application of dynamic pressing forces up to 1500 kg Fce/cm/sup 2/ demonstrated that the cyclical strength of carboborated coverings is 2.0-3.0 times higher than that of borated ones. The method of carboborating is recommended for strengthening the details of stamp and press tools.

Effect of austenitization conditions on kinetics of isothermal transformation of austenite of structural steels

International Nuclear Information System (INIS)

Konopleva, E.V.; Bayazitov, V.M.; Abramov, O.V.; Kozlova, A.G.

1987-01-01

Effect of austenization of kinetics of pearlite and bainite transformations for steels with different carbon content differing by alloying character and degree has been investigated. Austenization temperature increase is shown to leads to retardation of ferrite-pearlite transformation in low- and medium-carbon alloyed steels. Step-like holding in the region of austenite stable state (850, 950 deg) after high-temperature heating (1100 deg C) increases the rate of transformation partially recovering its kinetics and decomposition velocity after low-temperature heating in steels alloyed advantageously with carbide-forming elements (08Kh2G2F, 30Kh3) and does not affect kinetics in the 35Kh, 30KhGSN2A, 45N5 steels. Increase of heating temperature and growth of an austenite grain cause considerable acceleration of bainite transformation, increase of the temperaure of bainite transformation beginning and increase of the transformation amplitude in the 08Kh2G2F, 30Kh3 steels and affect weakly kinetics in steels with mixed alloying (30KhGSN2A) or low-alloy one (35Kh). The bainite transformation rate in the 45N5 steelite does not depend on austenization. The effect of additional acceleration of bainite transformation as a result holding after high-temperature heating in those steels, where activation of transformation occurs with increase of heating temperature

Effect of heat treatment on microstructure, mechanical properties and erosion resistance of cast 23-8-N nitronic steel

International Nuclear Information System (INIS)

Kumar, Avnish; Sharma, Ashok; Goel, S.K.

2015-01-01

Effects of heat treatment on microstructure, mechanical properties and erosion behavior of cast 23-8-N nitronic steel were studied. A series of heat treatments were carried out in the temperature range of 1180–1240 °C to observe the effect on microstructure. Optimum heat treatment cycle was obtained at 1220 °C for holding time of 150 min, which leads to dissolution of carbides, formation of equiaxed grains and twins. Heat treatment has shown improvement in tensile strength, toughness, impact strength and work hardening capacity, however at the cost of marginal reduction in hardness and yield strength. This resulted in improvement of erosion resistance of cast 23-8-N nitronic steel. The microstructures, fractured surfaces and phases were studied by optical microscopy, field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) analysis respectively

Electrochemical impedance spectrometry using Inconel 690, zircaloy 4, 316Ti steel, 17-4-PH, UR52N et URSB8. Simulation in tritiated water. Tome 2

International Nuclear Information System (INIS)

Bellanger, G.

1994-11-01

The redox potential of 3 H 2 O, as well as the corrosion potentials in this medium are found, abnormally, in the trans-passive region. This is completely different from behavior in the chemical industry or in the water in nuclear powers. With such behavior, there will be breakdowns of the protective oxide layers, and in the presence of chloride there will be immediate pitting. Polarization and electrochemical impedance spectrometry curves are presented and discussed. These curves make it possible to ascertain the corrosion domains and to compare the kinetics of different stainless steel alloys. These corrosion kinetics and the corrosion potentials provide a classification of the steels studied here: Inconel 690, zircaloy 4, 316 Ti steel, 17-4-PH, UR52N et URSB8. From the results it can be concluded that URSB8 has the best corrosion resistance. (author). 13 refs., 522 figs., tabs

Influence of sulphur and phosphorus impurities on ductility of 25Kh2NMFA steel during forging

International Nuclear Information System (INIS)

Onishchenko, A.K.

1989-01-01

Using cylindrical samples of the 25Kh2NMFA steel with sulfur and phosphorus content in the range of 0.001-0.030%, tensile test with the rate of deformation 10 -3 s -1 at the temperatures of 800-1200 deg C has been conducted. Analysis of fracture foci and plasticity diagrams has shown, that to ensure ductility during forging and high mechanical properties, the content of sulfur and phosphorus impurities in the 25Kh2NMFA steel must not exceed 0.015%

Parameter optimization for steel quenching by C02-laser irradiation

International Nuclear Information System (INIS)

Moryashchev, S.F.; Kislitsyn, A.A.; Kosyrev, F.K.

1984-01-01

The dependence of average absorption factor on maximal temperature of the article surface during quenching by CO 2 -laser irradiation was determined empirically. The calculations of depth of a hardening zone and process productivity in 40 Kh, 4Kh13 steels and Armco-iron with regard to this dependence were conducted

Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

Energy Technology Data Exchange (ETDEWEB)

Muradova, R G; Zakharov, V A; Kuzin, A P; Gol' tsov, V A; Podgajskij, M S [Donetskij Politekhnicheskij Inst. (Ukrainian SSR); Donetskij Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii (Ukrainian SSR))

1982-01-01

The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory).

Hydrogen effect on mechanical properties and flake formation in the 10KhSND steel rolled plates

International Nuclear Information System (INIS)

Muradova, R.G.; Zakharov, V.A.; Kuzin, A.P.; Gol'tsov, V.A.; Podgajskij, M.S.

1982-01-01

The effect of hydrogen on mechanical properties of the 10KhSND steel rolled plates during natural aging is studied. Optimum period of metal acceptance tests, which are advisable to conduct after 5-7 day natural aging of finished products, are found out. The technique is worked out and a safe hydrogen content to prevent flake formation in the 10KhSND steel is determined. It is shown that a safe hydrogen content is dependent on the experiment conditions (sample dimensions, conditions of cooling, and prehistory)

Properties of structural steels melted out of high-purity charge

International Nuclear Information System (INIS)

Marchenko, V.N.; Sergeeva, T.K.; Kondakova, N.K.; Morozov, V.P.; Madorskij, L.L.

1993-01-01

A comparative evaluation has been made of impurities, mechanical properties and hydrogen embirittlement parameters for steels type 40Kh and 40KhS produced by electrometallurgical method with the use of direct reduced charge (DR-steels) and melted in an open-hearth furnace. Investigation results have shown that 40Kh and 40KhS Dr-steels have more coarse austenitic grains and experience more complete transformation of martensite into ferritic-pearlitic mixture on tempering. Threshold stresses increase 2.5 times due to purity enhancement at the expense of application of direct reduced charge

Effect of Titanium on the Microstructure and Mechanical Properties of High-Carbon Martensitic Stainless Steel 8Cr13MoV

Directory of Open Access Journals (Sweden)

Wen-Tao Yu

2016-08-01

Full Text Available The effect of titanium on the carbides and mechanical properties of martensitic stainless steel 8Cr13MoV was studied. The results showed that TiCs not only acted as nucleation sites for δ-Fe and eutectic carbides, leading to the refinement of the microstructure, but also inhibited the formation of eutectic carbides M7C3. The addition of titanium in steel also promoted the transformation of M7C3-type to M23C6-type carbides, and consequently more carbides could be dissolved into the matrix during hot processing as demonstrated by the determination of extracted carbides from the steel matrix. Meanwhile, titanium suppressed the precipitation of secondary carbides during annealing. The appropriate amount of titanium addition decreased the size and fraction of primary carbides in the as-cast ingot, and improved the mechanical properties of the annealed steel.

Study of 16KhSN high strength steel in different structural states and under working conditions

International Nuclear Information System (INIS)

Skudnov, V.A.; Vorob'ev, I.A.; Kutyajkin, V.G.; Bugrov, Yu.V.

1985-01-01

A study was made on the effect of deformation degree (up to 60%) during reducing, drawing and heat treatment (annealing at 750 deg C), quenching from 930 deg C and tempering at 350 deg C) on strength, plasticity, hardening degree, notch sensitivity, density and elasticity characteristics of the steel. The effect of test temperature (from-196 up to 1000 deg C) on tensile strength and plasticity was studied as well. It was established that drawing and reducing of 16KhSN steel in annealed state with strain degrees of up to 60% results to increase of strength characteristics 1.7...2.3 times and decrease of plasticity characteristics by 15...23%, strain hardening coefficient - 2.2 times and the maximum strain energy - by 80 MJ/m 3 . Hardening heat treatment (quenching from 930 deg C+temperating at 350 deg C) affects on mechanical properties of 16KhSN steel in much the same way as cold working, but strength characteristics of heat-treated steel increase 2.6...3.6 times and the maximum strain energy grows by 640 MJ/m 3 . Systematic data on the effect of temperature (-196...1000 deg C) and tensile rate (4 mm/min...5m/s) on strength and plasticity of 16KhSN steel in annealed state were obtained

Cooling rate and microstructure of surface layers of 5KhNM steel, machined by electroerosion method

International Nuclear Information System (INIS)

Foteev, N.K.; Ploshkin, V.V.; Lyakishev, V.A.; Shirokov, S.V.

1982-01-01

The cooling rate and microstructure of surface layers of steel 5KhNM machined by electroerosion method have been studied. It is shown that the difference in heating rate of the surface layers with electric discharge over the 5KhNM steel samples depth results in the intensive size reduction of the microstructure. In the surface layer alongside with martensite residual austenite is present, the lattice period of which increases with the increase of pulse duration, carbide phase of complex composition appears, and concentrational heterogeneity in alloying elements (except carbon) is absent

Cooling rate and microstructure of surface layers of 5KhNM steel, machined by electroerosion method

Energy Technology Data Exchange (ETDEWEB)

Foteev, N.K.; Ploshkin, V.V.; Lyakishev, V.A.; Shirokov, S.V.

1982-01-01

The cooling rate and microstructure of surface layers of steel 5KhNM machined by electroerosion method have been studied. It is shown that the difference in heating rate of the surface layers with electric discharge over the 5KhNM steel samples depth results in the intensive size reduction of the microstructure. In the surface layer alongside with martensite residual austenite is present, the lattice period of which increases with the increase of pulse duration, carbide phase of complex composition appears, and concentrational heterogeneity in alloying elements (except carbon) is absent.

Irradiation and annealing behavior of 15Kh2MFA reactor pressure vessel steel

International Nuclear Information System (INIS)

Popp, K.; Bergmann, U.; Bergner, F.; Hampe, E.; Leonhardt, W.D.; Schuetzler, H.P.; Viehrig, H.W.

1992-01-01

This work deals with the mechanical properties of RPV steels used WWER-440. The materials under investigation were a forging (base metal 15Kh2MFA) and the corresponding weld. Charpy V-notch specimens and tensile test specimens were irradiated in the WWER-2 Rheinsberg at about 270 C up to the two neutron fluence levels of 4 x 10 18 and 5 x 10 19 n/cm 2 (E>1MeV). Post-irradiation annealing heat treatments were performed, among others a 475 C/152 h treatment of technical interest. (orig.)

Quality of austenite chrome-nickel steel made by gas-oxygen refining

International Nuclear Information System (INIS)

Fel'dgandler, Eh.G.; Levin, F.L.; Moshkevich, E.A.; Shifrin, Eh.V.; Movshovich, V.S.; Pargamonov, E.A.

1991-01-01

Properties and structure were investigated of austenitic 03Kh18N11 and 08KhN10T steels melted at gas oxygen refining aggregates. It was established that mechanical and corrosion properties of rolling of such steels were in agreement with standard properties of metal of open melting. Sheet 08Kh18N10T steel has the level of strength and plasticity regulated for 12Kh18N10T steel. As steel of 08Kh18N10T holds the complex of high mechanical and corrosion properties, 08Kh18N10T is recommended to be replace by 12Kh18N10T with the aim of decrease of titanium usage and increase of process efficiency

Electroplastic drawing of stainless steels

International Nuclear Information System (INIS)

Troitskij, O.A.; Spitsyn, V.I.; Sokolov, N.V.; Ryzhkov, V.G.

1977-01-01

Effect of electroplastic drawing on mechanical, magnetic and electrical properties of wire of 12Kh18N10T and Kh13N13M2 steels was studied. Pulse, direct and alternating currents were used. Direct and alternating current densities were 400 A/mm 2 , mean density of pulse current was 200 A/mm 2 . The investigations have shown that the current density increase results in decreasing the wire strengthening intensity though in increasing plastic properties. As a result of electroplastic drawing the growth of magnetic characteristics of wire occurs

Coarsening of (Fe, Cr)23C6 carbide phase on the tempering of 14Kh17N2 chromium-nickel steel

International Nuclear Information System (INIS)

Psarev, V.I.

2002-01-01

Paper lists the results of computer analysis of distribution according to sizes (Fe, Cr) 23 C 6 microparticles resulting from 14Kh17N2 steel tempering under 700 Deg C. Data were obtained at the maximum beneficial magnification of a light microscope. The mentioned curves of distribution densities are characterized by more reliable run from most permissible sizes of dispersed particles. Application of general rules of distributions and of previously elaborated procedure to identify experimental histograms with theoretical distributions enables to derive valuable information on dynamics of coarsening of a disperse phase in this case, as well [ru

Corrosion fatigue investigation of a high nitrogen 12% Cr-steel and of a high strength martensitic PH 13-8 Mo steel under simulated steam turbine conditions. Final report

International Nuclear Information System (INIS)

Schmitt-Thomas, K.G.; Schweigart, H.

1992-01-01

This report summarizes the results of the corrosion fatigue investigations of two martensitic stainless steels (PH 13-8 Mo, X20 CrMoV 12 1; corrosion medium: 0,01 m NaCl or 22 wt% NaCl; pH value 3 or 7). The working programm includes electrochemical and corrosion fatigue tests. Also chemical analysis, mechanical-technological and metallographical as SEM investigations were performed. (orig.)

Long-term strength and allowable stresses of grade 10Kh9MFB and X10CrMoVNb9-1 (T91/P91) chromium heat-resistant steels

Science.gov (United States)

Skorobogatykh, V. N.; Danyushevskiy, I. A.; Schenkova, I. A.; Prudnikov, D. A.

2015-04-01

Currently, grade X10CrMoVNb9-1 (T91, P91) and 10Kh9MFB (10Kh9MFB-Sh) chromium steels are widely applied in equipment manufacturing for thermal power plants in Russia and abroad. Compilation and comparison of tensile, impact, and long-term strength tests results accumulated for many years of investigations of foreign grade X10CrMoVNb9-1, T91, P91, and domestic grade 10Kh9MFB (10Kh9MFB-Sh) steels is carried out. The property identity of metals investigated is established. High strength and plastic properties of steels, from which pipes and other products are made, for operation under creep conditions are confirmed. Design characteristics of long-term strength on the basis of tests with more than one million of hour-samples are determined ( and at temperatures of 500-650°C). The table of recommended allowable stresses for grade 10Kh9MFB, 10Kh9MFB-SH, X10CrMoVNb9-1, T91, and P91 steels is developed. The long-time properties of pipe welded joints of grade 10Kh9MFB+10Kh9MFB, 10Kh9MFB-Sh+10Kh9MFB-Sh, X10CrMoVNb9-1+X10CrMoVNb9-1, P91+P91, T91+T91, 10Kh9MFB (10Kh9MFB-Sh)+X10CrMoVNb9-1(T/P91) steels is researched. The welded joint reduction factor is experimentally determined.

Effect of high-temperature exposure on the mechanical properties of 18Cr–8Ni–W–Nb–V–N stainless steel

International Nuclear Information System (INIS)

Nikulin, I.; Kipelova, A.; Kaibyshev, R.

2012-01-01

Highlights: ► Niobium stabilized 18Cr–8Ni austenitic steel was subjected to long-time aging. ► The main phases precipitated during aging are Z-phase and Laves-phase. ► Intragranular phases and solid solution are responsible for tensile strength. ► Intergranular particles affect impact toughness. - Abstract: The change in the mechanical properties of 18Cr–8Ni–W–Nb–V–N austenitic stainless steel due to aging was investigated at room temperature and 650 °C. It was shown that long-term aging decreases strength characteristics despite increasing hardness. The impact toughness decreases from 255 J/cm 2 for an un-aged steel to 135 J/cm 2 for the steel aged for 3000 h. However, evidence of ductile fracture was found even after long-term aging. This study suggests that the reduction in impact toughness occurs due to the precipitation of Z-phase and Laves-phase particles at the grain boundaries. The degradation of impact toughness and mechanical properties with aging is discussed in terms of microstructure evolution, secondary phase precipitations and fracture mechanisms.

Seven-sphere and the exceptional N=7 and N=8 superconformal algebras

International Nuclear Information System (INIS)

Guenaydin, M.; Ketov, S.V.

1996-01-01

We study realisations of the exceptional non-linear (quadratically generated, or W-type) N=8 and N=7 superconformal algebras with Spin(7) and G 2 affine symmetry currents, respectively. Both the N=8 and N=7 algebras admit unitary highest-weight representations in terms of a single boson and free fermions in 8 of Spin(7) and 7 of G 2 , with the central charges c 8 =26/5 and c 7 =5, respectively. Furthermore, we show that the general coset ansaetze for the N=8 and N=7 algebras naturally lead to the coset spaces SO(8) x U(1)/SO(7) and SO(7) x U(1)/G 2 , respectively, as the additional consistent solutions for certain values of the central charge. The coset space SO(8)/SO(7) is the seven-sphere S 7 , whereas the space SO(7)/G 2 represents the seven-sphere with torsion, S 7 T . The division algebra of octonions and the associated triality properties of SO(8) play an essential role in all these realisations. We also comment on some possible applications of our results to string theory. (orig.)

17 CFR 8.13 - Answer to charges.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Answer to charges. 8.13 Section 8.13 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION EXCHANGE PROCEDURES FOR DISCIPLINARY, SUMMARY, AND MEMBERSHIP DENIAL ACTIONS Disciplinary Procedure § 8.13 Answer to...

Microstructure evolution and deformation mechanism change in 0.98C-8.3Mn-0.04N steel during compressive deformation

International Nuclear Information System (INIS)

Wang, T.S.; Hou, R.J.; Lv, B.; Zhang, M.; Zhang, F.C.

2007-01-01

The microstructure evolution and the deformation mechanism change in 0.98C-8.3Mn-0.04N steel during compressive deformation at room temperature have been studied as a function of the reduction in the range of 20-60%. Experimental results show that with the reduction increasing the microstructure of the deformed sample changes from dislocation substructures into the dominant twins plus dislocations. This suggests that the plastic deformation mechanism changes from the dislocation slip to the dominant deformation twinning. The minimum reduction for deformation twins starting is estimated to be at between 30 and 40%. With the reduction further increases to more than 40%, the deformation twinning is operative and the thickness of deformation twins gradually decreases to nanoscale and shear bands occur. These high-density twins can be curved by the formation of shear bands. In addition, both transmission electron microscopy and X-ray diffraction examinations confirm the inexistence of deformation-induced martensites in these deformed samples

41 CFR 105-8.170-13 - Delegation.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Delegation. 105-8.170-13 Section 105-8.170-13 Public Contracts and Property Management Federal Property Management Regulations... HANDICAP IN PROGRAMS OR ACTIVITIES CONDUCTED BY GENERAL SERVICES ADMINISTRATION § 105-8.170-13 Delegation...

Properties of 40N3M powder structural steel

International Nuclear Information System (INIS)

Moskvina, T.P.; Gulyaev, A.P.; Gulyaev, I.A.; Byakov, S.V.; Melent'ev, I.V.; Morgun, G.N.

1984-01-01

Effect of the fabrication technique of compact slabs made of the 40N3M powder structural steel on mechanical properties with determination of a cold brittleness threshold was studied. It is established that after a thermal treatment at a density close to 100% a powder steel is sufficiently close to steel, rolled of an ingot, but is second in reference to steel in its ductility and impact strength. Properties of powder steel obtained by the method of dynamic hot forming (DHF) and hot extrusion are practically equal, but the first method has definite advantages as it allows to obtain details with a definitive form. The above investigation permits to recommend an application of the 40N3M powder steel fabricated by the DHF methods. The optimum thermal treatment course is: quenching+high annealing

Effect of the isothermal transformation temperature on the fine structure of steel-12Kh1MF

International Nuclear Information System (INIS)

Mints, I.I.; Berezina, T.G.; Lanskaya, K.A.

1976-01-01

For detailed analysis of bainite and pearlite in steel 12Kh1MF, homogeneous structures were obtained by isothermal annealing at 350, 450, 500, and 650 0 for 1 h. Isothermal transformation of austenite leads to the formation of bainite at 350-500 0 and pearlite at 650 0 . The austenitizing temperature was 980 0 for both types of samples, with holding for 20 min. For comparison, the plates were quenched from 980 0 and 1050 0 in ice-cold brine. The investigation was conducted with use of light and electron microscopes and x-ray analysis. The long-term strength was also determined. Isothermal treatment of steel 12Kh1MF at 350-500 0 C leads to the formation of a structure consisting of upper and lower bainite. At 500 0 the structure consists primarily of upper bainite, and at 350 0 of lower bainite. With tempering of the steel with a structure of upper and lower bainite at 730 0 for 3 h the dislocations undergo redistribution of the polygonization type within ferrite needles, with development of a cellular substructure. The acicular structure of the matrix is retained in this case. The density and evenness of the distribution of carbides is higher in upper bainite than in lower bainite. Steel 12Kh1MF with a structure of upper bainite is more susceptible to recrystallization as compared with a structure of lower bainite, which is responsible for the higher heat resistance of the latter

Coordination Polymers of N, Nʼ-di-(8-Hydroxyquinolinolyl- 5-methyl-N, N-diethyl-1,3-propane diamine (QEPD

Directory of Open Access Journals (Sweden)

Asha D. Patel

2010-01-01

Full Text Available Coordination polymers containing a novel bis(oxine bidentate ligand, namely N,Nʼ-di(8-hydroxyquinolinolyl-5-methyl-N,Nʼ-diethyl-1,3-propane diamine (QEPD have been prepared with the metal ions Zn(II, Cu(II, Ni(II, Co(II and Mn(II. The novel bis-(bidentate ligand was synthesized by condensation of 5-chloromethyl-8-hydroxyquinoline hydrochloride with N,Nʼ-diethyl-1,2- propane diamine in the presence of a base catalyses. All of these coordination polymers and the parent ligand were characterized by elemental analyses, IR spectral and diffuse reflectance spectral studies. The thermal stability and number- average molecular weights (Mn¯ of all of the coordination polymers were determined by thermogravimetric analyses and non-aqueous conductometric titrations, respectively. In addition, all of the coordination polymers have been characterized by their magnetic susceptibilities.

6 CFR 13.8 - Service of Complaint.

Science.gov (United States)

2010-01-01

... 6 Domestic Security 1 2010-01-01 2010-01-01 false Service of Complaint. 13.8 Section 13.8 Domestic Security DEPARTMENT OF HOMELAND SECURITY, OFFICE OF THE SECRETARY PROGRAM FRAUD CIVIL REMEDIES § 13.8 Service of Complaint. (a) Service of a Complaint must be Made by certified or registered mail or by...

15 CFR 8c.40 - Employment.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Employment. 8c.40 Section 8c.40... BASIS OF HANDICAP IN PROGRAMS OR ACTIVITIES CONDUCTED BY THE DEPARTMENT OF COMMERCE § 8c.40 Employment... discrimination in employment under any program or activity conducted by the agency. The definitions, requirements...

In situ TEM study of G-phase precipitates under heavy ion irradiation in CF8 cast austenitic stainless steel

Science.gov (United States)

Chen, Wei-Ying; Li, Meimei; Zhang, Xuan; Kirk, Marquis A.; Baldo, Peter M.; Lian, Tiangan

2015-09-01

Thermally-aged cast austenitic stainless steels (CASS) CF8 was irradiated with 1 MeV Kr ions at 300, 350 and 400 °C to 1.88 × 1019 ions/m2 (∼3 dpa) at the IVEM-Tandem Facility at the Argonne National Laboratory. Before irradiation, the distribution of G-phase precipitates in the ferrite showed spatial variations, and both their size and density were affected by the ferrite-austenite phase boundary and presence of M23C6 carbides. Under 300 °C irradiation, in situ TEM observation showed G-phase precipitates were relatively unchanged in the vicinity of the phase boundary M23C6 carbides, while the density of G-phase precipitates increased with increasing dose within the ferrite matrix. Coarsening of G-phase precipitates was observed in the vicinity of phase boundary M23C6 carbides at 350 °C and 400 °C.

Defect accumulation in welded joints of 12Kh1MF steel steam pipelines during creep

International Nuclear Information System (INIS)

Anokhov, A.E.; Alekhova, I.A.

1982-01-01

Technique for investigation of micropore accumulation in 12Kh1MF steel welded joints is proposed. The micropore density in different zones of welded joints in non-uniform. It is shown that failure localization in welded joint in the softening zone during the creep takes place due to the micropore priority accumulation in this zone. It is found out that accumulation of residual deformations in different zones of 12Kh1MF welded joints under creep runs more uniformly as the level of working stresses decreases and test duration increases

On change of vanadium carbide state during 20Kh3MVF steel heat treatment

International Nuclear Information System (INIS)

Gitgarts, M.I.; Maksimenko, V.N.

1975-01-01

The Xray diffraction study of vanadium carbide MC has been made in the steel-20KH3MVF quenched from 970 and 1040 deg and tempered at 660 deg for 210 hrs. It has been found that the constant of the MC crystal lattice regularly varies with the temperature of isothermal hold-up. In the steel tempered after quenching two vanadium carbides of different content could co-exist simultaneously: carbide formed in the quenching process and carbide formed during tempering. The discovered effect of the temperature dependence of the MC content is, evidently, inherent also to other steels containing vanadium

Superheat effect on bainite steel hardenability

International Nuclear Information System (INIS)

Kubachek, V.V.; Sklyuev, P.V.

1978-01-01

The bainite hardenability of 34KhN1M and 35 KhN1M2Ph steels has been investigated by the end-face hardening technique. It is established that, as the temperature of austenitization rises from 900 to 1280 deg C, the temperature of bainite transformation increases and bainite hardenability of the steels falls off. A repeated slow heating to 900 deg C of previously overheated 34KhN1M steel breaks up grain, lowers the temperature of the bainite transformation and raises the hardenability to values obtained with ordinary hardening from 900 deg C. A similar heating of previously overheated 35KhN1M2Ph steel is accompanied by restoration of initial coarse grains and maintenance of both the elevated bainite transformation temperature and to lower hardenability corresponding to hardening from the temperature of previous overheating

In situ TEM study of G-phase precipitates under heavy ion irradiation in CF8 cast austenitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Chen, Wei-Ying [Argonne National Laboratory, Argonne, IL 60439 (United States); University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Li, Meimei; Zhang, Xuan; Kirk, Marquis A.; Baldo, Peter M. [Argonne National Laboratory, Argonne, IL 60439 (United States); Lian, Tiangan [Electric Power Research Institute, Palo Alto, CA 94304 (United States)

2015-09-15

Thermally-aged cast austenitic stainless steels (CASS) CF8 was irradiated with 1 MeV Kr ions at 300, 350 and 400 °C to 1.88 × 10{sup 19} ions/m{sup 2} (∼3 dpa) at the IVEM-Tandem Facility at the Argonne National Laboratory. Before irradiation, the distribution of G-phase precipitates in the ferrite showed spatial variations, and both their size and density were affected by the ferrite–austenite phase boundary and presence of M{sub 23}C{sub 6} carbides. Under 300 °C irradiation, in situ TEM observation showed G-phase precipitates were relatively unchanged in the vicinity of the phase boundary M{sub 23}C{sub 6} carbides, while the density of G-phase precipitates increased with increasing dose within the ferrite matrix. Coarsening of G-phase precipitates was observed in the vicinity of phase boundary M{sub 23}C{sub 6} carbides at 350 °C and 400 °C.

Changes in structure and phase composition of chromium diffusion layer on stainless steels after long annealing

International Nuclear Information System (INIS)

Knyazev, E.V.; Voshedchenko, B.M.; Voskresenskij, Yu.A.

1985-01-01

A study was made on the effect of elevated temperatures UU and long holdings at heat on structure, phase composition and properties of chromium diffusion layer on austenitic chromium-nickel stainless steels 10Kh18N10TVD, 10Kh15N30M4B, 10Kh11N23T3MR, 10Kh21N28V6M3. The following mechanism of processes taking place in diffusion chromium layer is presented. The steady drop of chromium concentrations is observed after diffusion saturation. Chromium redistribution related with system transformation to more equilibrium state and simultaneous decarburization of steel surfaces takes place in diffusion layers of 10Kh15N30M4B and 10Kh21N28V6M3 steels after annealing at different temperatures and holdings at heat. Decarburization of steel surface layers is practically excluded in diffusion layers of 10Kh18N10T-VD and 10Kh11N23T3MR steels. Diffusion chromium-saturated layer stays effective only on 10Kh18N10T-VD and 10Kh11N23T3MR steels on heating up to 1000 deq C with holding up to 250 h

Effect of preliminary heat treatment on phase transformations and properties of the Kh15N5D2T (VNS-2) steel

International Nuclear Information System (INIS)

Madyanov, S.A.; Voronenko, B.I.; Makhnev, E.S.

1978-01-01

It is shown that preliminary heat treatment has a significant effect on the α→γ transformation kinetics, the quantity of residual austenite, the grain size and mechanical properties of the Kh15N5D2T steel after final heat treatment. The preliminary heat treatment regimes leading to the increase of the quantity of residual austenite and to grain refining increase the work of crack propagation in the finally strengthened state. The optimum properties were obtained after threefold preliminary tempering for 1h at 650 deg C. An approximately constant relation of α- and γ-phases (approximately 50%) is observed at 625 deg C irrespective of the investigated regimes of preliminary heat treatment

40 CFR 1502.8 - Writing.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Writing. 1502.8 Section 1502.8 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY ENVIRONMENTAL IMPACT STATEMENT § 1502.8 Writing. Environmental impact statements shall be written in plain language and may use appropriate graphics so that...

40 CFR 164.8 - Publication.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Publication. 164.8 Section 164.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS RULES OF PRACTICE... OTHER HEARINGS CALLED PURSUANT TO SECTION 6 OF THE ACT General § 164.8 Publication. All notices of...

Investigation into the Cyclic Strength of the Bodies of Steam Shutoff Valves from 10Kh9MFB-Sh Steel

Science.gov (United States)

Skorobogatykh, V. N.; Kunavin, S. A.; Prudnikov, D. A.; Shchenkova, I. A.; Bazhenov, A. M.; Zadoinyi, V. A.; Starkovskii, G. L.

2018-02-01

Steam shutoff valves are operated under complex loading conditions at thermal and nuclear power stations. In addition to exposure to high temperature and stresses resulting in fatigue, these valves are subjected to cyclic loads in heating-up-cooling down, opening-closing, etc. cycles. The number of these cycles to be specified in designing the valves should not exceed the maximum allowable value. Hence, the problem of cyclic failure rate of steam shutoff valve bodies is critical. This paper continues the previous publications about properties of the construction material for steam shutoff valve bodies (grade 10Kh9MFB-Sh steel) produced by electroslag melting and gives the results of investigation into the cyclic strength of this material. Fatigue curves for the steal used for manufacturing steam shutoff valve bodies are presented. The experimental data are compared with the calculated fatigue curves plotted using the procedures outlined in PNAE G-002-986 and RD 10-249-98. It is confirmed that these procedures may be used in designing valve bodies from 10Kh9MFB-Sh steel. The effect of the cyclic damage after preliminary cyclic loading of the specimens according to the prescribed load conditions on the high-temperature strength of the steel is examined. The influence of cyclic failure rate on the long-term strength was investigated using cylindrical specimens with a smooth working section in the as-made conditions and after two regimes of preliminary cyclic loading (training) at a working temperature of 570°C and the number of load cycles exceeding the design value, which was 2 × 103 cycles. The experiments corroborated that the material (10Kh9MFB-Sh steel) of the body manufactured by the method of electroslag melting had high resistance to cyclic failure rate. No effect of cyclic damages in the metal of the investigated specimens on the high-temperature strength has been found.

40 CFR 1508.8 - Effects.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Effects. 1508.8 Section 1508.8 Protection of Environment COUNCIL ON ENVIRONMENTAL QUALITY TERMINOLOGY AND INDEX § 1508.8 Effects. Effects include: (a) Direct effects, which are caused by the action and occur at the same time and place. (b...

Clinical and Molecular Characteristics of Human Rotavirus G8P[8] Outbreak Strain, Japan, 2014.

Science.gov (United States)

Kondo, Kenji; Tsugawa, Takeshi; Ono, Mayumi; Ohara, Toshio; Fujibayashi, Shinsuke; Tahara, Yasuo; Kubo, Noriaki; Nakata, Shuji; Higashidate, Yoshihito; Fujii, Yoshiki; Katayama, Kazuhiko; Yoto, Yuko; Tsutsumi, Hiroyuki

2017-06-01

During March-July 2014, rotavirus G8P[8] emerged as the predominant cause of rotavirus gastroenteritis among children in Hokkaido Prefecture, Japan. Clinical characteristics were similar for infections caused by G8 and non-G8 strains. Sequence and phylogenetic analyses suggest the strains were generated by multiple reassortment events between DS-1-like P[8] strains and bovine strains from Asia.

7 CFR 319.8-13 - From Northwest Mexico.

Science.gov (United States)

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false From Northwest Mexico. 319.8-13 Section 319.8-13... for the Entry of Cotton and Covers from Mexico § 319.8-13 From Northwest Mexico. Contingent upon continued freedom of Northwest Mexico and of the West Coast of Mexico from infestations of the pink bollworm...

Manufacture of rings of 08Kh18N10T sheet for internal structures of WWER type reactors

International Nuclear Information System (INIS)

Fojta, A.; Nitka, B.

1984-01-01

Technology is presented of the manufacture of rings for the jacket, shaft, core catcher and shaft bottom of WWER-440 reactors produced by Vitkovice Steel Works. The rings are manufactured from sheets of austenitic steel 08Kh18N10T. The materials and technology problems are discussed of sheet production, ring welding technology and annealing following welding. The plastic properties are assessed of the welded joints and problems are outlined of ring production for WWER-1000 reactors. (B.S.)

[Effect of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae].

Science.gov (United States)

Wang, Yan-ping; Wu, Jin-tao; Wang, Zi-lu; Zheng, Yang-yu; Zhang, Guang-dong; Yu, Jin-hua

2013-01-01

To determine the effects of KH2PO4 on the odonto- and osteogenic differentiation potential of human stem cells from apical papillae (SCAP) in vitro. SCAP were isolated and cultured respectively in alpha minimum essential medium (α-MEM) or α-MEM containing 1.8 mmol/L KH2PO4. Alkaline phosphatase (ALP) activity, alizarin red staining, real-time reverse transcription polymerase chain reaction (RT-PCR) and Western blotting were used to examine the odonto and osteogenic potential of SCAP in the two media. SCAP cultured in α-MEM containing 1.8 mmol/L KH2PO4 exhibited a higher ALP activity [(0.370 ± 0.013) Sigma unit×min(-1)×mg(-1)] at day 3 than control group [(0.285 ± 0.008) Sigma unit×min(-1)×mg(-1)] and KH2PO4-treated SCAP formed more calcified nodules at day 5 [(0.539 ± 0.007) µg/g] and day 7 [(1.617 ± 0.042) µg/g] than those in normal medium [(0.138 ± 0.037) µg/g, P odonto- and osteogenic markers were significantly up-regulated after the stimulation of KH2PO4 at day 3 and 7 respectively, as compared with control group. 1.8 mmol/L KH2PO4 can promote the odonto and osteogenic differentiation potential of human SCAP.

Quality of structural steel melted by single-slag process

International Nuclear Information System (INIS)

Levin, A.M.; Andreev, V.I.; Monastyrskij, A.V.; Drozdova, M.F.; Pashchenko, V.E.; Orzhekh, M.B.

1982-01-01

The 40Kh and 12KhN3A steels were used to compare the quality of the metal manufactured according to several variants of a single-slag process with the metal of a conventional melting technology. Investigation results show, that a single-slag process metal has higher sulfides and oxides contents as well as an increased anisotropy of mechanical properties while its tendency to flake formation is weaker due to a less degree of gas saturation. It is marked that anisotropy in the properties and a sulfide content may be decreased by out-of-furnace treatment of steels

The mutation frequency of 8-oxo-7,8 dihydroguanine (8-oxoG) situated in a multiply damaged site: comparison of a single and two closely opposed 8-oxodG in Escherichia coli

International Nuclear Information System (INIS)

Malyarchuk, S.G.; Youngblood, R.C.; Landry, A.M.; Quillin, E.; Harrison, L.

2003-01-01

Full text: A multiply damaged site (MDS) is defined as >= two lesions within a distance of 10-15 base pairs (bp). MDS generated by ionizing radiation contains oxidative base damage, and in vitro studies have indicated that if the base damage is less than 3 bp apart, repair of one lesion is inhibited until repair of the lesion in the opposite strand is completed. Inhibition of repair could result in an increase in the mutation frequency of the base damage. We have designed an assay to determine whether a closely opposed lesion causes an increase in adenine insertion opposite an 8-oxodG in bacteria. The double-stranded oligonucleotides (with no damage, each single 8-oxodG or the MDS) were ligated into the firefly luciferase coding region of a reporter vector and transformed into wild type or MutY-deficient bacteria. The MDS contained an 8-oxodG in the transcribed strand (T) and a second 8-oxodG immediately 5' to this lesion in the non-transcribed strand (NT). During two rounds of replication, insertion of adenine opposite the 8-oxodG in the T or NT strand results in a translation termination codon at position 444 or 445, respectively. In wild-type bacteria, we detected a translation stop at a frequency of 0.15% (codon 444) and 0.09% (codon 445) with a single 8-oxodG in the T or NT strand, respectively. This was enhanced ∼3 fold when single lesions were replicated in MutY-deficient bacteria. Positioning an 8-oxodG in the T strand within the MDS enhanced the mutation frequency by ∼2 fold in wild-type bacteria and 8 fold in Mut Y-deficient bacteria, while the mutation frequency of the 8-oxodG in the NT strand increased by 6 fold in Mut Y-deficient bacteria. This enhancement of mutation frequency supports the in vitro MDS studies, which demonstrated the inability of base excision repair to completely repair closely opposed lesions

Microstructural evolution in 13Cr-8Ni-2.5Mo-2Al martensitic precipitation-hardened stainless steel

International Nuclear Information System (INIS)

Ping, D.H.; Ohnuma, M.; Hirakawa, Y.; Kadoya, Y.; Hono, K.

2005-01-01

The microstructure of 13Cr-8Ni-2.5Mo-2Al martensitic precipitation-hardened (PH) stainless steel has been investigated using transmission electron microscopy, three-dimensional atom probe and small-angle X-ray scattering. A high number density (∼10 23-25 m -3 ) of ultra-fine (1-6 nm) β-NiAl precipitates are formed during aging at 450-620 deg. C, which are spherical in shape and dispersed uniformly with perfect coherency with the matrix. As the annealing temperature increases, the size and concentration of the precipitates increase concurrently while the number density decreases. The Mo and Cr segregation to the precipitate-matrix interface has been detected and is suggested to suppress precipitate coarsening. In the sample aged for 500 h at 450 deg. C, the matrix decomposes into Cr-rich (α') and Cr-poor (α) regions. The decrease in the strength at higher temperature (above 550 deg. C) is attributed to the formation of larger carbides and reverted austenite

Heat treatment effect on the properties of the EhP767 maraging steel welded joints

International Nuclear Information System (INIS)

Taver, E.I.; Piskarev, M.N.; Yushchenko, K.A.; Pustovit, A.I.; Anisimova, M.S.

1977-01-01

Heat treatment effect on properties of welded joints of maraging 03Kh13N4K13M3T (EhP767) steel with yield strength over 150 kgs/mm 2 has been investigated. It is shown, that change in impact strength of aged joints at - 196 deg C depends on the amount of residual austenite and grain size. To stabilize 20-40 % residual austenite heat treatment regimes have been developed. Recommended are quenching at 1030-1050 deg C, sub-zero treatment and aging at 520 deg C for 16 hrs

Cerebrospinal fluid IL-12p40, CXCL13 and IL-8 as a combinatorial biomarker of active intrathecal inflammation.

Directory of Open Access Journals (Sweden)

Bibiana Bielekova

Full Text Available Diagnosis and management of the neuroinflammatory diseases of the central nervous system (CNS are hindered by the lack of reliable biomarkers of active intrathecal inflammation. We hypothesized that measuring several putative inflammatory biomarkers simultaneously will augment specificity and sensitivity of the biomarker to the clinically useful range. Based on our pilot experiment in which we measured 18 inflammatory biomarkers in 10-fold concentrated cerebrospinal fluid (CSF derived from 16 untreated patients with highly active multiple sclerosis (MS we selected a combination of three CSF biomarkers, IL-12p40, CXCL13 and IL-8, for further validation.Concentrations of IL-12p40, CXCL13 and IL-8 were determined in a blinded fashion in CSF samples from an initial cohort (n = 72 and a confirmatory cohort (n = 167 of prospectively collected, untreated subjects presenting for a diagnostic work-up of possible neuroimmunological disorder. Diagnostic conclusion was based on a thorough clinical workup, which included laboratory assessment of the blood and CSF, neuroimaging and longitudinal follow-up. Receiver operating characteristic (ROC curve analysis in conjunction with principal component analysis (PCA, which was used to combine information from all three biomarkers, assessed the diagnostic value of measured biomarkers.Each of the three biomarkers was significantly increased in MS and other inflammatory neurological disease (OIND in comparison to non-inflammatory neurological disorder patients (NIND at least in one cohort. However, considering all three biomarkers together improved accuracy of predicting the presence of intrathecal inflammation to the consistently good to excellent range (area under the ROC curve = 0.868-0.924.Future clinical studies will determine if a combinatorial biomarker consisting of CSF IL-12p40, CXCL13 and IL-8 provides utility in determining the presence of active intrathecal inflammation in diagnostically

Structural features and properties of the laser-deposited nickel alloy layer on a KhV4F tool steel after heat treatment

Science.gov (United States)

Shcherbakov, V. S.; Dikova, Ts. D.; Stavrev, D. S.

2017-07-01

The study and application of the materials that are stable in the temperature range up to 1000°C are necessary to repair forming dies operating in this range. Nickel-based alloys can be used for this purpose. The structural state of a nickel alloy layer deposited onto a KhV4F tool steel and then heat treated is investigated. KhV4F tool steel (RF GOST) samples are subjected to laser deposition using a pulsed Nd:YAG laser. A nickel-based material (0.02C-73.8Ni-2.5Nb-19.5Cr-1.9Fe-2.8Mn) is employed for laser deposition. After laser deposition, the samples are subjected to heat treatment at 400°C for 5 h, 600°C for 1 h, 800°C for 1 h, and 1000°C for 1 h. The microstructure, the phase composition, and the microhardness of the deposited layer are studied. The structure of the initial deposited layer has relatively large grains (20-40 μm in size). The morphology is characterized by a cellular-dendritic structure in the transition zone. The following two structural constituents with a characteristic dendritic structure are revealed: a supersaturated nickel-based γ solid solution and a chromium-based bcc α solid solution. In the initial state and after heat treatment, the hardness of the deposited material (210-240 HV 0.1) is lower than the hardness of the base material (400-440 HV 0.1). Only after heat treatment at 600°C for 1 h, the hardness increases to 240-250 HV0.1. Structure heredity in the form of a dendritic morphology is observed at temperatures of 400, 600, and 800°C. The following sharp change in the structural state is detected upon heat treatment at 1000°C for 1 h: the dendritic morphology changes into a typical α + γ crystalline structure. The hardness of the base material decreases significantly to 160-180 HV 0.1. The low hardness of the deposited layer implies the use of the layer material in limited volume to repair the forming surfaces of dies and molds for die casting. However, the high ductility of the deposited layer of the nickel

Syntheses of DL-[2-13C]leucine and its use in the preparation of [3-DL-[2-13C]leucine]oxytocin and [8-DL-[2-13C]leucine]oxytocin

International Nuclear Information System (INIS)

Viswanatha, V.; Larsen, B.; Hruby, V.J.

1979-01-01

DL-[2- 13 C]Leucine was prepared by condensing the sodium salt of ethyl acetamido-[2- 13 C]cyanoacetate with isobutylbromide in hexamethylphosphoroustriamide followed by acid hydrolysis. N-BOC-DL-[2- 13 C]Leucine was prepared and incorporated into [8-DL-[2- 13 C]leucine]oxytocin by total synthesis. The 13 C-labeled hormone derivative [8-[2- 13 C]leucine]oxytocin was separated from its 8-position diastereoisomer by partition chromatography. The specifically 13 C-labeled peptide hormone diastereoisomeric analog [3-DL-[2- 13 C]leucine]oxytocin also was prepared by solid phase peptide synthesis. No suitable solvent system for partition chromatography separation of the latter diastereoisomeric peptide mixture could be found. However an excellent preparative separation of the diastereoisomers could be obtained by reverse phase high pressure liquid chromatography on a partisil 10 M9 ODS column using the solvent system 0.05 M ammonium acetate (pH 4.0), acetonitrile (81:19, v/v) to give pure [3-[2- 13 C]leucine]oxytocin and [3-D-[2- 13 C]leucine]oxytocin. An excellent separation of [8-[2- 13 C]leucine]oxytocin and the corresponding delata-D-leucine diastereoisomer derivative could also be accomplished by high pressure liquid chromatography. (author)

Measurement of 167Er(n,p)167Ho reaction at 13.5 and 14.8 MeV

International Nuclear Information System (INIS)

Luo, Junhua; Liu, Jun; Han, Jiuning; Jiang, Li; Liu, Rong; Ge, Suhong; Liu, Zhenlai

2013-01-01

We have measured the 167 Er(n,p) 167 Ho cross-sections at two different neutron energies 13.5 and 14.8 MeV. Measurements were performed at Pd-300 neutron generator of Chinese Academy of Engineering Physics (CAEP) with monoenergetic neutrons produced via the 3 H(d,n) 4 He reaction using a tritium–titanium (T–Ti) target. Induced gamma activities were measured by a high-resolution gamma-ray spectrometer with high-purity germanium (HPGe) detector. The data for 167 Er(n,p) 167 Ho reaction cross-sections are reported to be 2.2±0.6 and 2.8±1.4 mb at 13.5±0.2 and 14.8±0.2 MeV incident neutron energies, respectively. The cross sections were also estimated with the TALYS-1.4 nuclear model code and compared with experimental data found in the literature, and with the comprehensive evaluation data in ENDF/B-VII.1 and JEFF-3.1/A libraries. - Highlights: • D–T neutron source was used to measure cross sections using activation method. • 27 Al(n,α) 24 Na was used as the monitor for the measurement. • The cross sections for the 167 Er(n,p) 167 Ho reactions have been measured. • Contribution of the interfering reaction 170 Er(n,α) 167 Dy was subtracted. • The results were compared with previous data and with evaluation data

Strain ageing of the 15Kh2MFA steel at 500 and 550 deg C

International Nuclear Information System (INIS)

Maksimovich, G.G.; Azbukin, V.G.; Krylova, R.P.; Tretyak, I.Yu.; Bardachevskaya, T.V.

1978-01-01

The effect of ageing at high temperatures and under high stresses on strength and plasticity of the 15Kh2MFA steel has been studied. The steel was kept at 500 and at 550 deg C for 100, 1000 and 2500 hours without stress and under stress of 0.5 and 0.9 of the long-term strength limit (sigmasub(ls)). Ageing at 500 deg C without stress and under 0.5 sigmasub(ls) changed neither strength nor plasticity of the steel; under 0.9 sigmasub(ls) the strength somewhat decreased. Ageing at 550 deg C for 1000 hours resulted in an appreciable stress drop

Labelling and evaluation of new stabilised neurotensin (8-13) analogues for SPET

International Nuclear Information System (INIS)

Chavatte, K.; Terriere, D.; Jeannin, L.

1998-01-01

Neurotensin (8-13) analogues were biologically stabilised by replacement of the peptide bond between amino acids 8 and 9 by the reduced ψ(CH 2 -NH) isostere. DTPA analogues for In-111 labelling and 2-bromo-phenyl-acetyl analogues for radioiodination, showed receptor affinities in the low nanomolar range in combination with a biological half live in human plasma up to 275 minutes. Biodistribution studies in male Wistar rats of metabolically stabilised and non-stabilised 111 In-DTPA-NT(8-13) analogues showed a major clearance from the blood through the kidneys. 125 I-labelled Neurotensin (8-13) analogues showed accumulation up to 2.2% of the injected dose per g tissue in the liver which might be an important disadvantage when diagnosis of tumours in the gut is aimed. It is strongly suggested that stabilised neurotensin (8-13) analogues whether labelled with In-111, I-123 and the near future with Tc-99m, may act as new potential peptidergic radiopharmaceuticals for SPET diagnosis of different NT-receptor positive tumours like non-endocrine pancreas carcinoma, small cell lung carcinoma or colon adeno carcinoma. It is enticing to speculate that metabolically stabilised Neurotensin (8-13) analogues labelled with an appropriate isotope might be useful in therapy of different human cancers. (author)

Heating temperature effect on ferritic grain size of rotor steel

International Nuclear Information System (INIS)

Cheremnykh, V.G.; Derevyankin, E.V.; Sakulin, A.A.

1983-01-01

The heating temperature effect on ferritic grain size of two steels 13Kh1M1FA and 25Kh1M1FA is evaluated. It is shown that exposure time increase at heating temperatures below 1000 deg C up to 10h changes but slightly the size of the Cr-Mo-V ferritic grain of rotor steel cooled with 25 deg C/h rate. Heating up to 1000 deg C and above leads to substantial ferritic grain growth. The kinetics of ferritic grain growth is determined by the behaviour of phases controlling the austenitic grain growth, such as carbonitrides VCsub(0.14)Nsub(0.78) in 13Kh1M1FA steel and VCsub(0.18)Nsub(0.72) in 25Kh1M1FA steel. Reduction of carbon and alloying elements content in steel composition observed at the liquation over rotor length leads to a certain decrease of ferritic grain resistance to super heating

Investigation of fretting corrosion of vacuum-chrome-plated vt3-1 titanium alloy in pair with unprotected vt3-1 alloy and 40khnma steel

International Nuclear Information System (INIS)

Rojkh, I.L.; Koltunova, L.N.; Vejtsman, M.G.; Birman, Ya.N.; Skosarev, A.V.; Kogan, I.S.

1978-01-01

The character of destruction of contacting surfaces in the process of fretting corrosion of titanium alloy VT3-1 chromized in vacuum in pair with unprotected alloy VT3-1 and steel 40KhNMA has been studied by scanning electron microscopy, electronography, and recording the surface profile. The specific load was 200 kg/cm 2 , vibration amplitude 50 mkm and frequency 500 Hz. It has been established that pairs unprotected with coating are subjected to intensive fretting corrosion especially when they are made of titanium alloy. For the pair chromized alloy VT3-1 - unprotected alloy VT3-1 no destruction of a chromized surface is observed. Vacuum chromium coating in the pair with steel 40KhNMA reveals similar properties as in pair with a titanium alloy. The surface of a steel sample is destroyed because of fretting corrosion, though the intensity of corrosion is lower than in the case of unprotected pairs. Vacuum chromium coating is recommended for protection of titanium alloy VT3-1 from fretting corrosion in pair with steel 40KhNMA or an alloy VT3-1 especially in those cases when various organic coatings are unsuitable

Simulation of Microdamage and Evaluation of Remaining Life of Steam Conduit Components from New-Generation Refractory Steel 10Kh9MF-Sh

Science.gov (United States)

Gladshtein, V. I.

2018-03-01

The effects of microdamage on the remaining life of high-temperature components of steam conduits from high-chromium steel 10Kh9MF-Sh and low-alloy steel 12Kh1M1F are compared. To simulate the microdamage, specimens with a circular notch and different relative diameters are fabricated. Specimens with a notch simulating the highest degree of microdamage and smooth specimens are tested for long-term strength. The coefficient of the remaining life of a conduit is computed for the range of relative damage presenting practical interest.

NMR structural studies of the ionizing radiation adduct 7-hydro-8-oxodeoxyguanosine (8-oxo-7H-dG) opposite deoxyadenosine in a DNA duplex. 8-oxo-7H-dG(syn)·dA(anti) alignment at lesion site

International Nuclear Information System (INIS)

Kouchakdjian, M.; Patel, D.J.; Bodepudi, V.; Shibutani, S.; Eisenberg, M.; Johnson, F.; Grollman, A.P.

1991-01-01

Proton NMR studies are reported on the complementary d(C1-C2-A3-C4-T5-A6-oxo-G7-T8-C9-A10-C11-C12)·d(G13-G14-T15-G16-A17-A18-T19-A20-G21-T22-G23-G24) dodecanucleotide duplex (designated 8-oxo-7H-dG·dA 12-mer), which contains a centrally located 7-hydro-8-oxodeoxyguanosine (8-oxo-7H-dG) residue, a group commonly found in DNA that has been exposed to ionizing radiation or oxidizing free radicals. From the NMR spectra it can be deduced that this moiety exists as two tautomers, or gives rise to two DNA conformations, that are in equilibrium and that exchange slowly. The present study focuses on the major component of the equilibrium that originates in the 6,8-dioxo tautomer of 8-oxo-7H-dG. The authors have assigned the exchangeable NH1, NH7, and NH 2 -2 base protons located on the Watson-Crick and Hoogsteen edges of 8-oxo-7H-dG7 in the 8-oxo-7H-dG·dA 12-mer duplex, using an analysis of one- and two-dimensional nuclear Overhauser enhancement (NOE) data in H 2 O solution. They were able to detect a set of intra- and interstrand NOEs between protons (exchangeable and nonexchangeable) on adjacent residues in the d(A6-oxo-G7-T8)·d(A17-A18-T19) trinucleotide segment centered about the lesion site that establishes stacking of the oxo-dG7(syn)·dA(anti) pair between stable Watson-Crick dA6·dT19 and dT8·A17 base pairs with minimal perturbation of the helix. The structural studies demonstrate that 8-oxo-7H-dG(syn)·dA(anti) forms a stable pair in the interior of the helix, providing a basis for the observed incorporation of dA opposite 8-oxo-7H-dG when readthrough occurs past this oxidized nucleoside base

Experience manufacturing and properties of the high-strength corrosion-resistant magnetic 03Kh12K12D2 steel

International Nuclear Information System (INIS)

Fel'dgandler, Eh.G.; Moshkevich, E.I.; Bakuma, S.F.; Bulat, S.I.; Tikhonenko, V.D.

1976-01-01

In industrial conditions, steel 03Kh12K12D2 (DI48-VD) was melted in a 7-tinduction furnace with subsequent vacuum arc remelting. Ingots of dia 500 and 630 mm were forged into slabs and forgings. The slabs were rolled into sheets, 40 mm thick, and the forgings were rolled into sectional shapes. To obtain the optimum mechanical, corrosion, and magnetic properties, the metal was annealed at 600 deg C (10 hr) and 650 deg C (5 and 10 hr). The developed melting and remelting process enabled to obtain steel meeting all the requirements as for the chemical composition, workability, and mechanical magnetic properties. On testing in water with high parameters (200 deg C, 16 kgf/cm 2 ) and in synthetic sea water (70-90 deg C) the corrosion rate did not exceed 1 μm per year

Effect of melting technique on grain size and heat resistance of the 12Kh1MF steel

International Nuclear Information System (INIS)

Lanskaya, K.A.; Kulikova, L.V.; Butneva, N.I.

1978-01-01

Investigated are the 12Kh1MF steel melted in open-hearth and arc furnaces (deoxidation by aluminium in 1.0 kg/t quantity) and then subjected to electroslag melting. The size of an austenitic grain depends on the residual contents of nitrogen and aluminium in steel. The open-hearth metal subjected to electroslag melting and containing a small quantity of nitrogen (0.006%) and aluminium (0.013%) has coarse austenitic grains and higher heat resistance compared to the steel melted in an arc furnace and also sub ected to electroslag melting. The nitride analysis of steel is carried out

Influence of quantity of non-martensite products of transformation on resistance to fracture of improving structural steel

International Nuclear Information System (INIS)

Gulyaev, A.P.; Golovanenko, Yu.S.; Zikeev, V.N.

1978-01-01

18KhNMFA, low-carbon, alloyed steel and 42KhMFA medium-carbon, alloyed steel have been examined. For the purpose of obtaining different structures in hardening the steel, different cooling rates, different temperatures and isothermal holding times are applied. The following has been shown: on tempering to the same hardness (HV 300), the presence of non-martensite structures in hardened state does not practically influence the standard mechanical properties of steel (sigmasub(B), sigmasub(0.2), delta, PSI). The resistance of steel to the brittle failure is enhanced by the uniform, fine-disperse distribution of the carbide phase in the structure of lower bainite (up to 80 % bainite in martensite for 42KhMF steel to be improved), as well as strongly fragmented packages of rack martensite-bainite (up to 50 % lower bainite in martensite of 18KhNMFA steel). The formation of the upper bainite in the structure of the hardened steels 18KhNMFA and 42KhMF results on tempering in the formation of coarse, non-uniform, branched carbide inclusions, and this, in its turn, leads to raising the cold-shortness threshold and to lowering the amount of work as required for propagation of a crack. The presence of ferritic-pearlitic structures in the structural steels hardened to martensite and bainite results in reducing the resistance of steel to the brittle failure; the presence of every 10 % ferritic-pearlitic component in martensite of the structural steels 18KhNMFA and 42KhMFA to be thermally improved, raises T 50 by 8 deg and 20 deg C, respectively

13 CFR 313.8 - Competitive process.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Competitive process. 313.8 Section... § 313.8 Competitive process. (a) Applications for assistance to develop a Strategic Plan or for an implementation grant shall be reviewed by EDA in accord with a competitive process as set forth in the applicable...

Recent G8, G20 Inclusive Multilevel Food Governance

Directory of Open Access Journals (Sweden)

John Kirton

2014-11-01

Full Text Available Innovative, integrative, local, and business-inclusive governance for food, agriculture, nutrition, health and wealth can be strengthened through informal global institutions led by the Group of Eight (G8 and the Group of Twenty (G20. Their regular summits include the most important countries’ leaders and have a comprehensive, synergistic agenda, and impulse, as well as the flexibility and authority to link issues, factors, and actors in new ways. The G8 has increasingly addressed food, agriculture, nutrition, health, and the link among them, involved business, civil society, and low-income countries, and made decisions intended to affect the lives of the poor in many locales. The G20 has contributed to some degree in such ways too. Of particular promise is the G8’s New Alliance on Food Security and Nutrition, launched in May 2012, and the G20’s AgResults program built on commitments made in June 2010. Yet there remains much that both institutions can and should do to meet the combined, complex, food-health-wealth challenge now confronting the global community, before the next food crisis comes.

G-8 leaders tackle global energy security

International Nuclear Information System (INIS)

Quevenco, R.

2006-01-01

Leaders of the Group of 8 countries backed the IAEA's work at their annual summit held 15-17 July 2006 in St. Petersburg, Russia. A concluding summary statement endorsed IAEA programmes and initiatives in areas of nuclear safety, security, and safeguards. The G8 nations adopted a St. Petersburg Plan of Action to increase transparency, predictability and stability of the global energy markets, improve the investment climate in the energy sector, promote energy efficiency and energy saving, diversify energy mix, ensure physical safety of critical energy infrastructure, reduce energy poverty and address climate change and sustainable development. In a statement on global energy security, the G8 said countries who have or are considering plans for nuclear energy believe it will contribute to global energy security while reducing air pollution and addressing climate change. The G8 said it acknowledged the efforts made in development by the Generation IV International Forum (GIF) and the IAEA's International Project on Innovative Nuclear Reactors and Fuel Cycles (INPRO). GIF and INPRO both bring together countries to develop next generation nuclear energy systems, including small reactors, very high temperature reactors and supercritical water-cooled reactors. The G8 reaffirmed its full commitment to all three pillars of the NPT and called on all States to comply with their NPT obligations, including IAEA safeguards as well as developing effective measures aimed at preventing trafficking in nuclear equipment, technology and materials. The G8 is seeking universal adherence to IAEA comprehensive safeguards agreements and is actively engaged in efforts to make comprehensive safeguards agreements together with an Additional Protocol the universally accepted verification standard. The G8 noted that an expansion of the peaceful use of nuclear energy must be carried forward in a manner consistent with nuclear non-proliferation commitments and standards. It discussed concrete

Study of cast and thermo-mechanically strengthened chromium-nickel nitrogen-containing steel

International Nuclear Information System (INIS)

Prokoshkina, V.G.; Kaputkina, L.M.; Svyazhin, A.G.

2000-01-01

The effect of nitrogen on the structure and strength of corrosion-resistant chromium-nickel steels after thermal and thermomechanical treatment is studied. The 06Kh15N7AD and 07Kh15N7DAMB steels alloying by nitrogen was accomplished through the basic composition steels remelting in the molecular nitrogen atmosphere under the pressure of 0.1-2.5 MPa. The 02Kh15N5DAF and 05Kh15N5DAM steels ingots were obtained through melting in a plasma furnace under the nitrogen pressure of 0.4MPA. The high-temperature thermomechanical treatment (HTMT) was performed by rolling with preliminary blanks heating up to 1050 deg C and the rolling end temperature not below 950 deg C. It is shown, that the HTMT of the nitrogen-containing steels makes it possible to obtain strength characteristics by 1.5 times exceeding the properties of traditionally applicable corrosion-resistant steels, whereby sufficiently high plasticity of the nitrogen-containing steel is retained [ru

IEA policies-G8 recommendations and an afterwards

International Nuclear Information System (INIS)

Onoda, Takao

2009-01-01

In response to threats posed to the future supply of energy and to the environment, the G8 leaders, in Gleneagles, UK in 2005, agreed to an initiative called the Gleneagles Plan of Action (GPOA) which addresses climate change, clean energy and sustainable development. In the GPOA, G8 leaders pledged to encourage the development of cleaner, more efficient and lower-emitting vehicles, and to promote their deployment by, among other means, asking the IEA to review existing standards and codes for vehicle efficiency and to identify best practices. In order to properly response to the above-mentioned requests from G8 leaders, the IEA has launched, among other activities, study on policies for 'transforming the way we use energy' focusing on end-use efficiency including the one in transport sector and made a comprehensive response to the GPOA at the 2008 G8 Summit Meeting in Japan with 25 recommendations on energy efficiency. Regarding these recommendations, the G8 leaders have proclaimed, in the G8 Hokkaido Toyako Summit Leaders Declaration, that they would maximize implementation of the IEA's 25 recommendations. This paper summarizes the IEA activities in transport sector regarding the GPOA and their findings and recommendations.

Effect of Spheroidizing Annealing on Microstructure and Mechanical Properties of High-Carbon Martensitic Stainless Steel 8Cr13MoV

Science.gov (United States)

Yu, Wen-Tao; Li, Jing; Shi, Cheng-Bin; Zhu, Qin-Tian

2017-02-01

The effects of holding time during both austenitizing and spheroidizing on microstructure and mechanical properties of high-carbon martensitic stainless steel 8Cr13MoV were experimentally studied. The results showed that the amount of carbides and the proportion of fine carbides decrease first and then increase with the increase in austenitizing time ( t 1) in the case of short spheroidizing time ( t 2), whereas the amount of the lamellar carbides increases. In the case of long t 2, both the amount of carbides and the proportion of fine carbides decrease, and the amount of the lamellar carbides did not increase. The hardness of the steel decreases first and then increases with the increase of t 1. Under the conditions of different t 1, the change in the size of carbides and hardness of the steel show a same trend with the variation of t 2. The size of spheroidized carbides increases, whereas the hardness of the steel decreases with increasing t 2. The longer the holding time of austenitizing, the higher is the spheroidizing rate at the earlier stage. However, the spheroidizing rate shows an opposite trend with t 1 at the later stage of spheroidizing. The effect of cooling rate on microstructure is similar with t 2. With increasing cooling rate, the dimension of carbides became smaller, and the amount of lamellar carbides increased. The elongation of the sample fracture exhibits no corresponding relationship with holding time, whereas it is closely related to the precipitation of secondary carbides caused by the alloying elements segregation.

40 CFR 60.8 - Performance tests.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Performance tests. 60.8 Section 60.8... PERFORMANCE FOR NEW STATIONARY SOURCES General Provisions § 60.8 Performance tests. (a) Except as specified in... conduct performance test(s) and furnish the Administrator a written report of the results of such...

G8 SUMMIT MEETING AT EVIAN

CERN Multimedia

2003-01-01

The Swiss and French authorities have informed CERN that plans are in hand for the safety and traffic arrangements associated with the G8 Summit Meeting, which will be held in Evian between 1 and 3 June 2003. Detailed information will be communicated in the coming weeks. However, changes to traffic arrangements on certain sections of the road network in the Canton of Geneva (particularly the left bank) and the neighbouring parts of France (specially Haute-Savoie) from 22 May 2003 can already be predicted. All pertinent information and any recommendations by the authorities concerned will be brought to the attention of the personnel as soon as possible. In the mean time, those concerned can consult the various Web sites devoted to this event, especially: - http://www.g8.fr/evian/english/home.html (French site); - http://www.g8info.ch/accueil.htm (Swiss site). Relations with the Host States Service http://www.cern.ch/relations/ Tel. 72848

[2,3,7,8,13,14,17,18-Octakis(ethylsulfanyl-5,10,15,20-porphyrazinato]zinc(II

Directory of Open Access Journals (Sweden)

Mehmet Akkurt

2010-08-01

Full Text Available In the title compound, [Zn(C32H40N8S8], the ZnII ion is coordinated by four N atoms in a slightly distorted square-planar environment. In addition, there is a Zn...S contact involving a symmetry-related S atom which, when considered, forms a pseudo-square-pyramidal coordination with respect to the ZnII ion. Three of the ethyl groups are disordered over two sites with occupancy ratios of 0.841 (10:0.159 (10, 0.802 (10:0.198 (10 and 0.457 (13:0.543 (13. Weak intramolecular C—H...N and C—H...S interactions contribute to the stability of the molecular conformation. Intermolecular C—H...S contacts, weak C—H...π interactions and π–π stacking interactions [centroid–centriod distances = 3.832 (4 and 3.850 (5 Å] contribute to the stabilization of the crystal structure.

40 CFR 257.3-8 - Safety.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Safety. 257.3-8 Section 257.3-8... and Practices § 257.3-8 Safety. (a) Explosive gases. The concentration of explosive gases generated by... shall not pose a hazard to the safety of persons or property from fires. This may be accomplished...

G8 Regional Security Governance through Sanctions and Force

Directory of Open Access Journals (Sweden)

John Kirton

2014-11-01

Full Text Available Why do the Group of Eight (G8 members approve its members’ use of material sanctions in some regional conflicts but military force in others?2 As an informal security institution composed of major democratic powers from North America, Europe and Asia, the G8 has often chosen sanctions, notably on Iran in 1980, Afghanistan in 1980, Sudan in 2004, North Korea in 2006, and Syria in 2011. It has increasingly chosen military force, notably in Iraq in 1990, Kosovo in 1999, the USSR over Afghanistan in 2001, Libya in 2011, and Mali in 2013. Yet the G8’s choice, initiation, commitment, compliance, implementation and effectiveness of both sanctions and force has varied. Force was chosen and used effectively only in the post cold war period, primarily where the target was close to southern Europe. A high relative-capability predominance of G8 members over the target country strongly produces the G8’s choice of force, but a high, direct, deadly threat from the target state to G8 countries does not. Geographic proximity and the connectivity coming from the former colonial relationship between G8 members and the target country only weakly cause the G8 to choose force. Support from the most relevant regional organization – the North Atlantic Treaty Organization – and support from the United Nations in the form of an authorizing UN Security Council or General Assembly resolution have a strong, positive effect on the G8’s choice of force. Accompanying accountability mechanisms from the G8 itself have a variable impact, as leaders’ iteration of the issue at subsequent summits does not increase compliance with G8 commitments on force-related cases, but their foreign ministers’ follow up does to a substantial degree.

40 CFR 750.8 - Cross-examination.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Cross-examination. 750.8 Section 750.8... Section 6 of the Toxic Substances Control Act § 750.8 Cross-examination. (a) After the close of the... cross-examination. The request shall be received by EPA within one week after a full transcript of the...

40 CFR 35.935-8 - Supervision.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Supervision. 35.935-8 Section 35.935-8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works-Clean Water Act § 35.935-8 Supervision. In the case of any project involving Step 3,...

8 CFR 236.13 - Ineligible aliens.

Science.gov (United States)

2010-01-01

... 8 Aliens and Nationality 1 2010-01-01 2010-01-01 false Ineligible aliens. 236.13 Section 236.13 Aliens and Nationality DEPARTMENT OF HOMELAND SECURITY IMMIGRATION REGULATIONS APPREHENSION AND DETENTION OF INADMISSIBLE AND DEPORTABLE ALIENS; REMOVAL OF ALIENS ORDERED REMOVED Family Unity Program § 236...

G8 global partnership. 2004-2005-2006 activity report; Partenariat mondial du G8. Rapport d'activite 2004-2005-2006

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-07-01

The Global Partnership Against the Spread of Weapons and Materials of Mass Destruction was launched by the heads of state and government of the G8 at the G8 summit in Kananaskis in June 2002. Fourteen other countries have since joined this G8 initiative. The aim of this partnership is to 'prevent terrorists, or those who harbor them, from acquiring or developing nuclear, chemical radiological and biological weapons, missiles, and related materials, equipment and technology'. Within the framework of the Partnership, the participants have agreed to support cooperation projects, starting with Russia, to promote non-proliferation, disarmament, the fight against terrorism and nuclear safety. The destruction of chemical weapons, the dismantling of decommissioned nuclear submarines, the disposal of fissile materials and the employment of former weapons scientists are among the priority concerns expressed. Ukraine has also been a beneficiary of this partnership since 2004. The participants in this initiative have agreed to contribute up to 20 billion dollars (up to 750 million euros from France) to support these projects over a period of ten years from 2002. A group of experts from the G8 on the Global Partnership (the GPWG = Global Partnership Working Group) meets regularly and gives an account of the progress made with this initiative in its annual report to the G8. These annual reports are published at the G8 summits. This document is the 2004 to 2006 activity report of the G8 global partnership.

On the adsorption-induced fatigue of structural steels in the presence of alcohols

International Nuclear Information System (INIS)

Loboiko, V.I.; Karpenko, G.V.; Vasilenko, I.I.

1976-01-01

The purpose of the work was to study he effect of anhydrous alcohols on the cyclic fatigue of steels in the absence of contact of the alcohol with atmospheric moisture during the testing process. A vacuum was created in the operating space and then the vacuum annealing was carried out in a bath with the sample and through metal vacuum connection the bath was filled with anhydrous alcohol. Studies were made on several construction steels (20Kh, 40Kh, 50Kh, and ShKh15); steels 40Kh, 50Kh, and ShKh15 were quenched from 840-860 0 C in oil and then tempered at 200 0 C (2 h), steel 20Kh was studied in the as-received state. It was shown that with increase in the carbon content of steel with a martensite structure, the decrease in strength in the presence of anhydrous alcohol was greater than in dry air. Experiments showed that anhydrous alcohol causes an adsorption decrease in the strength both of samples with preliminarily formed cracks and V-shaped stress concentrators and of smooth samples. The greatest adsorption effect of alcohols in our case, as in static fatigue, was observed in samples with cracks. A dependence was shown between the length of the carbon chain and the fatigue limit. This dependence indicates the monotone nature of the decrease in the fatigue limit with transfer from methyl to butyl and then to octyl alcohol

Evaluation of XD/A Plus and ST8G films for cephalometric radiography with Grenex G8 and BH-III screens.

Science.gov (United States)

Wakoh, M; Farman, A G; Scarfe, W C; Shibuya, H; Nishikawa, K; Kuroyanagi, K

1997-02-01

Sensitometric properties, clinical image quality, and patient dose requirements are important considerations when selecting film for cephalometrics. Two recently released films, XD/A Plus and ST 8G green sensitive films, were studied. The films were each combined with Grenex G8 (Fuji Medical) green-fluorescing matched and BH-III (Kasei Optonix) blue-fluorescing mismatched intensifying screens. The density response and resolution for each screen-film combination were evaluated by use of the characteristic curve and modulation transfer function. The kilovoltage settings providing clinically acceptable images were assessed individually by 12 observers. Clinically acceptable images for each combination were also compared, and the skin entrance doses in the temporomandibular joint region were determined. The average contrast at the most effective density range was found to be slightly higher for the BH-III group than for the G8 group. The modulation transfer function for the BH-III group was inferior to that for the G8 screens. There were no significant differences in diagnostically acceptable image quality among the four combinations; nevertheless the BH-III screen group required two to three times more exposure than the G8 screen group. XD/A Plus and ST8G films provide acceptable image detail for cephalometrics. To minimize the patient dose they should be used with green-emitting screens.

Mechanical and fracture properties at impact loading of selected steels for nuclear power engineering

International Nuclear Information System (INIS)

Buchar, J.; Bilek, Z.

1988-01-01

The possibilities are briefly characterized of experimental research of mechanical and fracture properties of steels used in nuclear power engineering. Attention is paid to plastic deformation and the assessment of fracture formation during impact loading. The results are reported for steels 15Kh2MFA and 10GN2MFA. For steel 15Kh2MFA the effect was also studied of neutron radiation at different temperatures. From the theory developed for non-irradiated material 10GN2MFA, a prediction is made within the original model of the fracture stress value for steel 15Kh2MFA in both non-irradiated and irradiated states. The conclusion is arrived at that the existing methods of assessing steel properties at impact load allow obtaining knowledge of all significant effects during actual stress, this using only small specimens of the materials. (Z.M.). 4 figs., 8 refs

Corrosion failure of a bolt made of the 25Kh1MF material

International Nuclear Information System (INIS)

Liska, V.; Cechova, D.; Velkoborsky, J.

1989-01-01

M36x4 bolts, of which there are 222 at each nuclear power plant unit, are made of the 25Kh1MF or 38KhN3MFA steel. They are located in an environment with elevated temperature, with damp air and with boric acid. Corrosion of these bolts is due to the rather poor metallurgical quality of the steel. No inadmissible inhomogeneities of the type of lines of inclusions occur in the bolt material produced by cold rolling but defects of the type of laps were found on the threads. It is suggested that if the cold rolling technology were obviated, corrosion failure of the bolts might not occur. (M.D.). 7 figs., 3 refs

Effect of nickel and MnS inclusions in the metal on the pitting corrosion of low-carbon stainless steels

International Nuclear Information System (INIS)

Frejman, L.I.; Nguen, The Dong; Volkov, D.E.; Konnov, Yu.P.

1986-01-01

The resistance to pitting corrosion of steels on the 03Kh17-03Kh18 base containing up to 20 % Ni at different levels of S and Mn impurities contamination is investigated. It is shown that up to 50 % of nickel introduced into ordinary steels with 5-6 % Ni is spent to compensate the resistance decrease caused by MnS inclusions. Full compensation is not attained even in the 10-20 %. Ni range in which nickel practically does not affect the resistance of neither ordinary, nor pure (without MnS) steels. Titanium introduction into ordinary steel on the Kh22N6 base permits to surpass the level of 03Kh17N3 pure steel resistance and attain the level of 03Kh17N6 pure steel almost by all characteristics (including passivated characteristics in sulfuric acid) besides pitting repassivity. In this property pure steels with Ni >or approx. 3 % surpass even the molybdenum containing 03Kh21NbM2T ordinary steel though they by far concede by passivation in sulfuric acid

Synthesis, Characterization, Antimicrobial Studies and Corrosion Inhibition Potential of 1,8-dimethyl-1,3,6,8,10,13-hexaazacyclotetradecane: Experimental and Quantum Chemical Studies

Directory of Open Access Journals (Sweden)

Henry U. Nwankwo

2016-02-01

Full Text Available The macrocylic ligand, 1,8-dimethyl-1,3,6,8,10,13-hexaazacyclotetradecane (MHACD was synthesized by the demetallation of its freshly synthesized Ni(II complex (NiMHACD. Successful synthesis of NiMHACD and the free ligand (MHACD was confirmed by various characterization techniques, including Fourier transform infra-red (FT-IR, proton nuclear magnetic resonance (1H-NMR, carbon-13 nuclear magnetic resonance (13C-NMR, ultraviolet-visible (UV-vis, and energy dispersive x-ray (EDX spectroscopic techniques. The anti-bacteria activities of MHACD were investigated against Staphylococcus aureus and Enterococcus species and the results showed that MHACD possesses a spectrum of activity against the two bacteria. The electrochemical cyclic voltammetry study on MHACD revealed that it is a redox active compound with promising catalytic properties in electrochemical applications. The inhibition potential of MHACD for mild steel corrosion in 1 M HCl was investigated using potentiodynamic polarization method. The results showed that MHACD inhibits steel corrosion as a mixed-type inhibitor, and the inhibition efficiency increases with increasing concentration of MHACD. The adsorption of MHACD obeys the Langmuir adsorption isotherm; it is spontaneous and involves competitive physisorption and chemisorption mechanisms. Quantum chemical calculations revealed that the energy of the highest occupied molecular orbital (HOMO of MHACD is high enough to favor forward donation of charges to the metal during adsorption and corrosion inhibition. Natural bond orbital (NBO analysis revealed the presence of various orbitals in the MHACD that are capable of donating or accepting electrons under favorable conditions.

Phase transformation and grain growth behavior of a nanocrystalline 18/8 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Kotan, Hasan, E-mail: hasankotan@gmail.com [Konya Necmettin Erbakan University, Department of Metallurgical & Materials Engineering, Konya 42090 (Turkey); Darling, Kris A. [US Army Research Laboratory, Weapons and Materials Research Directorate, RDRL-WMM-F, Aberdeen Proving Ground, MD 21005-5069 (United States)

2017-02-16

Fe-18Cr-8Ni and Fe-18Cr-8Ni-1Y (at%) stainless steel powders were nanostructured by mechanical alloying from elemental powders and subjected to 90 min annealing treatments at various temperatures. The microstructural evolutions as a function of alloy compositions and temperatures were investigated by in-situ and ex-situ x-ray diffraction experiments, transmission electron microscopy and focused ion beam microscopy. The dependence of hardness on the microstructure was utilized to study the mechanical changes. It was found that the resulting microstructures by mechanical alloying were bcc solid solution, the so-called α’-martensite structure. The high temperature in-situ x-ray diffraction experiments showed that the martensite-to-austenite reverse phase transformation was completed above 800 and 900 °C for Fe-18Cr-8Ni and Fe-18Cr-8Ni-1Y steels, respectively. A partial or complete retransformation to martensite was observed upon cooling to room temperature. Annealing of nanocrystalline Fe-18Cr-8Ni steel yielded grain growth reaching to micron sizes at 1100 °C while addition of 1 at% yttrium stabilized the microstructure around 160 nm grain size and 6 GPa hardness after 90 min annealing at 1200 °C.

Ilves : mida põrgut teeb Venemaa G8-s?

Index Scriptorium Estoniae

2007-01-01

President Toomas Hendrik Ilves viibis Prahas 4. ja 5. juunil 2007 toimunud konverentsil "Demokraatia ja julgeolek", kus ta seadis kahtluse alla selle, kas Euroopat rakettidega ähvardava Venemaa koht on ikka G8-s ja Euroopa Nõukogus. Ilmunud ka: Eesti Elu 8. juuni 2007, lk. 1,4, pealk.: Mida teeb Venemaa G8-s?, ingl. k. lk. 9, pealk.: Ilves: what is Russia doing in the G8? Vabariigi President töövisiidil Prahasse 4.-6.06.2007

40 CFR 205.57-8 - Continued testing.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Continued testing. 205.57-8 Section 205.57-8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) NOISE ABATEMENT PROGRAMS TRANSPORTATION EQUIPMENT NOISE EMISSION CONTROLS Medium and Heavy Trucks § 205.57-8 Continued...

Mechanical and microstructural behavior of oxide dispersion strengthened 8Cr-2W and 8Cr-1W steels during creep deformation

Energy Technology Data Exchange (ETDEWEB)

Shinozuka, K.; Tamura, M.; Esaka, H. [National Defense Academy, Dept. MS and E, Kanagawa (Japan); Shiba, K.; Nakamura, K. [Japan Atomic Energy Agency, Tokai-mura, Naga-gun, Ibaraki-ken (Japan)

2007-07-01

Full text of publication follows: Oxide dispersion strengthened (ODS) steel is a promising candidate for fusion reactor material because of excellent mechanical properties. However, the ODS steel exhibits some defects, such as mechanical anisotropy and little elongation . To reveal details of these defects, we investigated correlations between mechanical and microstructural behavior of ODS ferritic steels during creep deformation at high temperature. The materials used in this study are two kinds of hot rolled ODS steels: Fe-8Cr-2W-0.2V-0.1Ta-0.2Ti-0.4Y{sub 2}O{sub 3} (J1) and Fe-8Cr-1W-0.2Ti-0.4Y{sub 2}O{sub 3} (J2). Creep tests was carried out on specimens sampling along both the rolling direction and the cross direction at 670, 700 and 730 deg. C. Microstructural analyses were made on the normalized and tempered condition by using OM, SEM, TEM and XRD. Creep ruptured and interrupted specimens were also investigated. Both J1 and J2 existed two phases, namely martensite and {delta}-ferrite which was elongated in the rolling direction. Y-Ti complex oxide particles were finely dispersed in martensite and {delta}- ferrite phases. Results of creep tests indicated that the time-to-rupture of specimens of J1 were much longer than J2, and the time-to-rupture of specimens sampling along the rolling direction were longer than cross direction. Accordingly, J1 sampling along hot rolling direction was the strongest, for instance, the time-to-rupture was 11400 h at 700 deg. C and 162 MPa. All specimens indicated that elongation was less than 1.3 % and the rupture occurred at steady state creep region from creep curves. Internal cracks were propagated in martensite phase along elongated {delta}-ferrite phase in the direction of hot rolling. On the other hand, {delta}-ferrite phases seemed to prevent combining cracks. These results suggest that elongated {delta}-ferrite and internal clacks in martensite strongly affect on the anisotropy and little elongation of creep. (authors)

Evolution of secondary-phase precipitates during annealing of the 12Kh18N9T steel irradiated with neutrons to a dose of 5 DPA

Science.gov (United States)

Tsai, K. V.; Maksimkin, O. P.; Turubarova, L. G.

2007-03-01

The formation and evolution of thermally-induced secondary precipitates in an austenitic stainless steel 12Kh18N9T irradiated in the core of a laboratory reactor VVR-K to a dose of 5 dpa and subjected to post-radiation isochronous annealings for 1 h in a temperature range from 450 to 1050°C have been studied using transmission electron microscopy (TEM) and microhardness measurements. It has been shown that the formation of stitch (secondary) titanium carbides and M 23C6 carbides at grain and twin boundaries after annealing at 1050°C is preceded by a complex evolution of fineparticles of secondary phases (titanium carbides and nitrides) precipitated at dislocation loops and dislocations during annealing at temperatures above 750°C.

40 CFR 8.2 - Applicability and effect.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Applicability and effect. 8.2 Section 8... OF NONGOVERNMENTAL ACTIVITIES IN ANTARCTICA § 8.2 Applicability and effect. (a) This part is intended to ensure that potential environmental effects of nongovernmental activities undertaken in Antarctica...

G5..., G6..., G7..., G8..., G?

OpenAIRE

Monteiro, António

2001-01-01

O G8 tem as suas raízes no primitivo embrião do G5 quando, em 1973, o então Secretário de Estado do Tesouro americano, George Schultz, convocou os Ministros das Finanças da França, Japão, Reino Unido e República Federal da Alemanha para uma reunião. O objectivo era analisar como fazer face à primeira crise do petróleo da OPEC e subsequente recessão económica nos países mais industrializados, ao colapso do sistema monetário das taxas de câmbio de paridades fixas de Bretton-Woods e ao alargamen...

Nisin production of Lactococcus lactis N8 with hemin-stimulated cell respiration in fed-batch fermentation system.

Science.gov (United States)

Kördikanlıoğlu, Burcu; Şimşek, Ömer; Saris, Per E J

2015-01-01

In this study, nisin production of Lactococcus lactis N8 was optimized by independent variables of glucose, hemin and oxygen concentrations in fed-batch fermentation in which respiration of cells was stimulated with hemin. Response surface model was able to explain the changes of the nisin production of L. lactis N8 in fed-batch fermentation system with high fidelity (R(2) 98%) and insignificant lack of fit. Accordingly, the equation developed indicated the optimum parameters for glucose, hemin, and dissolved oxygen were 8 g L(-1) h(-1) , 3 μg mL(-1) and 40%, respectively. While 1711 IU mL(-1) nisin was produced by L. lactis N8 in control fed-batch fermentation, 5410 IU mL(-1) nisin production was achieved within the relevant optimum parameters where the respiration of cell was stimulated with hemin. Accordingly, nisin production was enhanced 3.1 fold in fed-batch fermentation using hemin. In conclusion the nisin production of L. lactis N8 was enhanced extensively as a result of increasing the biomass by stimulating the cell respiration with adding the hemin in the fed-batch fermentation. © 2015 American Institute of Chemical Engineers.

8-Hydroxy-2'-deoxyguanosine (8-OH-dG): A biomarker of oxidative damage in yellow bullheads chronically exposed to low-level radiation

International Nuclear Information System (INIS)

McCreedy, C.D.; Glickman, L.T.

1995-01-01

8-hydroxy-2'-deoxyguanosine (8-OH-dG), an oxidation product of the nucleotide deoxyguanosine (dG) was used as a biomarker to assess oxidative damage in brain and gill tissues of yellow bullhead catfish (Ameiurus natalis; n = 18) inhabiting an abandoned reactor reservoir contaminated with low levels of d137 Cs (Pond B, Savannah River Site, SC). DNA was isolated by chloroform-isoamyl extraction, enzymatically digested with Nuclease P1/Calf Intestinal Phosphatase, and analyzed by HPLC with electrochemical detection.Length, weight, age, condition and muscle 137 Cs activity of each fish were also determined. Concentrations of 8-OH-dG were greater in brain than in gill tissues. 8-OH-dG in gill tissues decreased as condition of fish increased, but as age increased, the effect of condition declined. Brain 8-OH-dG concentration was not related to age or condition of fish, but was greater in females and the interaction between gender and 137 Cs was significant. Brain 8-OH-dG was positively associated with muscle 137 Cs concentration among females, but was unrelated to 137 Cs concentration in males. At lower 137 Cs concentrations, females tended to have fewer oxidative DNA adducts in brian than did males. Deposition of somatic lipids into eggs may provide females some anti-oxidant benefit by diminishing the contribution of lipid peroxidation to DNA damage. 8-OH-dG is a sensitive biomarker of low-level radiation exposure, however, its application in fish requires consideration of factors such as gender, age, body-condition, and the tissue type sampled

G8 global partnership. 2004-2005-2006 activity report

International Nuclear Information System (INIS)

2007-01-01

The Global Partnership Against the Spread of Weapons and Materials of Mass Destruction was launched by the heads of state and government of the G8 at the G8 summit in Kananaskis in June 2002. Fourteen other countries have since joined this G8 initiative. The aim of this partnership is to 'prevent terrorists, or those who harbor them, from acquiring or developing nuclear, chemical radiological and biological weapons, missiles, and related materials, equipment and technology'. Within the framework of the Partnership, the participants have agreed to support cooperation projects, starting with Russia, to promote non-proliferation, disarmament, the fight against terrorism and nuclear safety. The destruction of chemical weapons, the dismantling of decommissioned nuclear submarines, the disposal of fissile materials and the employment of former weapons scientists are among the priority concerns expressed. Ukraine has also been a beneficiary of this partnership since 2004. The participants in this initiative have agreed to contribute up to 20 billion dollars (up to 750 million euros from France) to support these projects over a period of ten years from 2002. A group of experts from the G8 on the Global Partnership (the GPWG = Global Partnership Working Group) meets regularly and gives an account of the progress made with this initiative in its annual report to the G8. These annual reports are published at the G8 summits. This document is the 2004 to 2006 activity report of the G8 global partnership

Effect of smelt aluminium on mechanical properties of steels

International Nuclear Information System (INIS)

Ryabov, V.R.; Dykhno, I.S.; Deev, G.F.; Karikh, V.V.

1987-01-01

Effect of smelt aluminium on mechanical properties of armco-iron and 12 Kh18N10T steel is studied. It is stated that in smelt aluminium and aluminium alloy contact with armco-iron the sample ductility is decreased. Corrosion effect of smelt alluminium on (18Kh15N5AM3) steel in the form of reinforced wire in aluminium-steel KAS-1A composite material is investigted. It is stated in experiment that during smelt alluminium-steel contact interaction of heterogeneous phases takes place

Reverted austenite in PH 13-8 Mo maraging steels

International Nuclear Information System (INIS)

Schnitzer, Ronald; Radis, Rene; Noehrer, Matthias; Schober, Michael; Hochfellner, Rainer; Zinner, Silvia; Povoden-Karadeniz, E.; Kozeschnik, Ernst; Leitner, Harald

2010-01-01

The mechanical properties of maraging steels are strongly influenced by the presence of reverted austenite. In this study, the morphology and chemical composition of reverted austenite in a corrosion resistant maraging steel was characterized using transmission electron microscopy (TEM) and atom probe tomography (APT). Two types of austenite, i.e. granular and elongated, are present after aging at 575 o C, whereby the content of the latter increases during aging. The investigations revealed that the austenite phase is enriched in Ni, which prevents the transformation to martensite during cooling. Inside and next to the austenitc areas, Mo and Cr-rich carbides, which form during the aging treatment, were found. Various aging treatments were performed to obtain the activation energy for the formation of reverted austenite. Additionally, the experimental data are compared with thermodynamic and kinetic simulations. Based on these results and the chemical composition changes of the phases, a model for the formation of reverted austenite is presented. It is concluded that precipitation of B2-ordered NiAl and formation of reverted austenite take place simultaneously during aging and that dissolution of precipitates is not essential for the initial formation of reverted austenite.

Theoretical study of [Li(H2O)n]+ and [K(H2O)n]+ (n = 1-4) complexes

International Nuclear Information System (INIS)

Wojcik, M.J.; Mains, G.J.; Devlin, J.P.

1995-01-01

The geometries, successive binding energies, vibrational frequencies, and infrared intensities are calculated for the [Li(H 2 O) n ] + and [K(H 2 O) n ] + (n = 1-4) complexes. The basis sets used are 6-31G * and LANL1DZ (Los Alamos ECP+DZ) at the SCF and MP2 levels. There is an agreement for calculated structures and frequencies between the MP2/6-31G * and MP2/LANL1DZ basis sets, which indicates that the latter can be used for calculations of water complexes with heavier ions. Our results are in a reasonable agreement with available experimental data and facilitate experimental study of these complexes. 19 refs., 4 figs., 6 tabs

Local corrosion of high alloy steels under biodeposits

International Nuclear Information System (INIS)

Korovyakova, M.D.; Nikitin, V.M.; Speshneva, N.V.

1999-01-01

Impact of the bacteriozenosis different structural-functional state under biodeposits on corrosion resistance of the 12Kh18N10T and Kh18N10T high-alloy steels in the natural seawater is studied. It is shown that saturation of natural micro communities by separate aerobic and facultative-anaerobic bacterial monocultures increases corrosion resistance of these steels by their overgrow with biodeposits [ru

Influence of isothermal thermomechanical treatment on structure and properties of structural steels

International Nuclear Information System (INIS)

Smirnov, M.A.; Kaletin, A.Yu.; Schastlivthev, V.M.; Kaletina, Yu.V.

1997-01-01

A study is made into the structure and mechanical properties of steel 35KhGSA and 37KhN3A after isothermal hardening resulting in bainitic structure formation as well as after low-temperature thermomechanical treatment (LTTMT) combining the plastic deformation at the temperature of bainitic transformation and subsequent isothermal hardening. It is shown that LTTMT permits and essential enhancement of strength properties in steel 35KhGSA, high plasticity and impact strength being reserved. This is associated with bainitic structure refinement. In steel 37KhN3A the process of carbide formation takes place along with bainitic transformation, and LTTMT results in lesser strengthening. LTTMT is fount to not practically affect the tendency of structural steels to bainitic brittleness. This treatment promotes some shift of brittleness manifestation to lower temperatures

Long-term behaviour of heat-resistant steels and high-temperature materials

International Nuclear Information System (INIS)

1987-01-01

This book contains 10 lectures with the following subjects: On the effect of thermal pretreatment on the structure and creep behaviour of the alloy 800 H (V. Guttmann, J. Timm); Material properties of heat resistant ferritic and austenitic steels after cold forming (W. Bendick, H. Weber); Investigations for judging the working behaviour of components made of alloy 800 and alloy 617 under creep stress (H.J. Penkalla, F. Schubert); Creep behaviour of gas turbine materials in hot gas (K.H. Kloos et al.); Effect of small cold forming on the creep beahviour of gas turbine blades made of Nimonic 90 (K.H. Keienburg et al.); Investigations on creep fatigue alternating load strength of nickel alloys (G. Raule); Change of structure, creep fatigue behaviour and life of X20 Cr Mo V 12 1 (by G. Eggeler et al.); Investigations on thermal fatigue behaviour (K.H. Mayer et al.); Creep behaviour of similar welds of the steels 13 Cr Mo 4 4, 14 MoV 6 3, 10 Cr Mo 910 and GS-17 Cr Mo V 5 11 (K. Niel et al.); Determining the creep crack behaviour of heat resistant steels with samples of different geometry (K. Maile, R. Tscheuschner). (orig.,/MM) [de

CARD15 single nucleotide polymorphisms 8, 12 and 13 are not increased in ethnic Danes with sarcoidosis

DEFF Research Database (Denmark)

Milman, Nils; Nielsen, Ole Haagen; Hviid, Thomas Vauvert F

2007-01-01

and SNP13, respectively, were performed by capillary electrophoresis single-strand confirmation polymorphism in 53 patients with histologically verified sarcoidosis and in 103 healthy controls. RESULTS: The frequencies of CARD15 mutations in sarcoidosis patients were: SNP8, 4/106 chromosomes (3.8%); SNP12...... with Crohn's disease. OBJECTIVES: To evaluate whether ethnic Danes with sarcoidosis have an increased frequency of CARD15 mutations compared to healthy control subjects. METHODS: Genotyping for CARD15 mutations R702W, G908R, and L1007fsinsC, also designated single nucleotide polymorphism (SNP) SNP8, SNP12......, 2/106 chromosomes (1.9%); SNP13, 2/106 chromosomes (1.9%); SNP8+SNP12+SNP13, 8/106 chromosomes (7.6%). All 8 patients were heterozygous. The frequencies in controls were: SNP8, 9/206 chromosomes (4.4%); SNP12, 2/206 chromosomes (1.0%); SNP13, 4/206 chromosomes (1.9%); SNP8+SNP12+SNP13, 15...

Effect of heat treatment and rotor steels composition on hydrogen solubility

International Nuclear Information System (INIS)

Ivanov, A.I.; Samojlenko, L.V.; Gorovaya, O.N.; Najdovskij, A.G.; Bilik, I.; Kret, Ya.

1988-01-01

Measurements of equilibrium hydrogen adsorption in samples of 27KhN3MFA and 25Kh2NMFA steels were conducted. Carbide inclusions and doping additions, typical for rotor steels, don't produce noticeable effect on hydrogen solubility in

A Weakest-Link Approach for Fatigue Limit of 30CrNiMo8 Steels (Preprint)

Science.gov (United States)

2011-03-01

34Application of a Weakest-Link Concept to the Fatigue Limit of the Bearing Steel Sae 52100 in a Bainitic Condition," Fatigue and Fracture of...AFRL-RX-WP-TP-2011-4206 A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) S. Ekwaro-Osire and H.V. Kulkarni Texas...2011 4. TITLE AND SUBTITLE A WEAKEST-LINK APPROACH FOR FATIGUE LIMIT OF 30CrNiMo8 STEELS (PREPRINT) 5a. CONTRACT NUMBER In-house 5b. GRANT

Investigation of intergranular corrosion resistance of Cr16Ni25NMo6 steel

International Nuclear Information System (INIS)

Kamenev, Yu.B.; Nazarov, A.A.; Kuusk, L.V.; Majdeburova, T.F.

1990-01-01

The effect of 08Kh16N25AM6 steel susceptibility to intergranular corrosion on its intergranular cracking resistance in high-temperature water is investigated. In addition, the performed tests point to the susceptibility of sensibilized Kh16N25AM6 steel to intergranular corrosion in media simulating an agressive environment of power generation equipment; the latter requires a strict control over the resistance of weld joints of the above steel to intergranular corrosion. It is shown that Kh16N25AM6 type steel in sensibilized state is susceptible to intercrystalline corrosion cracking in high-temperature water which correlates with its susceptibility to intergranular corrosion established by AM GOST 6032-84 and potentiodynamic reactivation methods

Investigation of 12Kh1MF steel resistance to brittle fractures

International Nuclear Information System (INIS)

Bologov, G.A.; Rushchits, T.Yu.

1977-01-01

The metal of hot-rolled steam pipe made of 12Kh1MF steel, which has been subjected to thermal treatment under laboratory conditions, and metal samples from acting steam pipes after different exploitation periods at 510-565 deg C have been investigated. The dependence of impact viscosity and its constituents on conditions of thermal treatment has been established. The energy consumed by the developing crack has been used as an impact viscosity criterion. Appropriate thermal treatment is capable of rehabilitating the impact viscosity of embrittled metal. Cold plastic deformation increases crack propagation rate in the initial metal and promotes embrittlement during exploitation. Ageing of the working metal reduces its capacity of stopping the developing crack and shifts the temperature threshold of brittleness towards positive temperature

Close toleranoe forging of chromium steel blades for powerful steam turbines

International Nuclear Information System (INIS)

Shastin, Eh.G.; Kositskij, Yu.N.; Lyubchits, G.A.

1989-01-01

Work on simulating technological process on die-forging hammer was performed in order to reduce the preparation period bringing technology of close tolerance forging of turbine blades to a commercial level. A special attention was paid to development of accurate forming of forgings of 20Kh13Sh, 12Kh13 and 15Kh11MFSh steels on screw presses with nominal effort equal to 80 and 144 MN

Determination of the cross section for (n,p) and (n,α) reactions on 165Ho at 13.5 and 14.8 MeV

International Nuclear Information System (INIS)

Luo, Junhua; An, Li; Jiang, Li; He, Long

2015-01-01

Activation cross-sections for the 165 Ho(n,p) 165 Dy and 165 Ho(n,α) 162 Tb reactions were measured by means of the activation method at 13.5 and 14.8 MeV, to resolve inconsistencies in existing data. A neutron beam produced via the 3 H(d,n) 4 He reaction was used. Statistical model calculations were performed using the nuclear-reaction codes EMPIRE-3.2 Malta and TALYS-1.6 with default parameters, at neutron energies varying from the reaction threshold to 20 MeV. Results are also discussed and compared with some corresponding values found in the literature. The calculational results on the 165 Ho(n,α) 162 Tb reaction agreed fairly well with experimental data, but there were large discrepancies in the results for the 165 Ho(n,p) 165 Dy reaction. - Highlights: • 27 Al(n,α) 24 Na was used as a monitor for neutron fleunce. • The cross sections for the 165 Ho(n,p) 165 Dy and 165 Ho(n,α) 162 Tb reactions were measured at 13.5 and 14.8 MeV neutron energies. • Nuclear reaction codes TALYS-1.6 and EMPIRE-3.2 Malta were used to model the reactions. • Inconsistency with previous data and with model calculations are noted

Special Features of Induction Annealing of Friction Stir Welded Joints of Medium-Alloy Steels

Science.gov (United States)

Priymak, E. Yu.; Stepanchukova, A. V.; Bashirova, E. V.; Fot, A. P.; Firsova, N. V.

2018-01-01

Welded joints of medium-alloy steels XJY750 and 40KhN2MA are studied in the initial condition and after different variants of annealing. Special features of the phase transformations occurring in the welded steels are determined. Optimum modes of annealing are recommended for the studied welded joints of drill pipes, which provide a high level of mechanical properties including the case of impact loading.

Construction of N=8 supergravity theories by dimensional reduction

International Nuclear Information System (INIS)

Boucher, W.

1985-01-01

In this paper I ask which N=8 supergravity theories in four dimensions can be obtained by dimensional reduction of the N=1 supergravity theory in eleven dimensions. Several years ago Scherk and Schwarz produced a particular class of N = 8 theories by giving a dimensional reduction scheme on the restricted class of coset spaces, G/H, with dim H=0 (and therefore dim G=7). I generalize their considerations by looking at arbitrary (seven-dimensional) coset spaces. Also, instead of giving a particular ansatz which happens to work, I set about the distinctly more difficult task of determining all ansatzes which produce N=8 theories. The basic ingredient of my dimensional reduction scheme is the demand that certain symmetries, including supersymmetry, be truncated consistently. I find the surprising result that the only N=8 theories obtainable within the contexts of my scheme are those theories already written down by Scherk and Schwarz. In particular dim H=0 and dim G=7. Independently of these considerations, I prove that any dimensional reduction scheme which consistently truncates supersymmetry must also be consistent with the equations of motion. I discuss Lorentz-invariant solutions of the theories of Scherk and Schwarz, pointing out that since the ansatz of Scherk and Schwarz consistently truncates supersymmetry, any solution of these theories is also a solution of the N=1 supergravity theory in eleven dimensions and, hence, in particular that there is a Freund-Rubin-type ansatz for these theories. However I demonstrate that for most gauge groups the ansatz must be trivial which implies that for these theories the cosmological constant of any Lorentz-invariant solution must be zero (classically). Finally, I make some comparisons with work by Manton on dimensional reduction. (orig.)

Influence of chemical heterogeneity of solid solutions on brittleness in chromium steels

International Nuclear Information System (INIS)

Madyanov, S.A.; Sedov, V.K.; Apaev, B.A.

1985-01-01

The role of chemical heterogeneity of solid solutions in formation of mechanical properties of Kh09, Kh15, Kh20, Kh19N2G5T chromium steels has been investigated. It is established that besides the known regioA of chemical heterogeneity in the vicinity of 475 deg C exists a high-temperature region (1000-1050 deg C), where maximum heteroge=- neity of chromium distribution in solid solution, is observed. Both types of chemical heterogeneity cause essential hardening of alloys, which becomes apparent in abrupt change of capability to microplastic deformation The mechanism of occurrence of the given temper brittleness consists in carbon diffusion into microvolunes enriched in carbide-forming elements

Investigation of the fabrication process of hot-worked stainless-steel and Mo sheathed PbMo6 S8 wires

International Nuclear Information System (INIS)

Yamasaki, H.; Kimura, Y.

1988-01-01

Stainless-steel and Mo sheathed PbMo 6 S 8 wires have been fabricated by hot working from modified PbS, Mo, and MoS 2 mixed powders which were prepared by reacting Pb, Mo, and S at 530 0 C. Critical current densities were investigated for different preparation conditions, and it is revealed that obtaining continuous current path between PbMo 6 S 8 grains is the most important factor to achieve high critical current density. The J/sub c/ value of 2.8 x 10 4 Acm 2 (8 T), 7.8 x 10 3 Acm 2 (15 T), and 1.3 x 10 3 Acm 2 (23 T) was observed for the PbMo 6 S/sub 7.0/ wire heat treated at 700 0 C.copic

Cyclic crack resistance of anticorrosion cladding-15Kh2MFA steel joint

International Nuclear Information System (INIS)

Zvezdin, Yu.I.; Nikiforchin, G.N.; Timofeev, B.T.; Zima, Yu.V.; Andrusiv, B.N.

1985-01-01

Cyclie crack resistance of transition zone in austenitic cladding steel 15Kh2MFA joint is studied, taking into account the geometry of fatigue cracks, fracture micromechanism and crack closure effect. Kinetics of crack development from the cladding to the basic metal and vice versa is considered. Microstructure of transition zone is investigated. The results obtained are considered as applied to WWER. It is emphasized, that the braking of fatigue cracks is observed at low asymmetry of loading cycle. Increased loading asymmetry accelerates sharply the alloy fracture due to the growth of subcladding crack, at that, the direction of crack propagation and the structure of transition zone are not of great importance

[2,3,7,8,13,14,17,18-Octa-kis(ethyl-sulfan-yl)-5,10,15,20-porphyrazinato]zinc(II).

Science.gov (United States)

Akkurt, Mehmet; Coşkun, Naciye Yılmaz; Kılıçaslan, Fatma Aytan; Yalçın, Sabiha Manav; Büyükgüngör, Orhan; Gül, Ahmet

2010-07-24

In the title compound, [Zn(C(32)H(40)N(8)S(8))], the Zn(II) ion is coordinated by four N atoms in a slightly distorted square-planar environment. In addition, there is a Zn⋯S contact involving a symmetry-related S atom which, when considered, forms a pseudo-square-pyramidal coordination with respect to the Zn(II) ion. Three of the ethyl groups are disordered over two sites with occupancy ratios of 0.841 (10):0.159 (10), 0.802 (10):0.198 (10) and 0.457 (13):0.543 (13). Weak intra-molecular C-H⋯N and C-H⋯S inter-actions contribute to the stability of the mol-ecular conformation. Inter-molecular C-H⋯S contacts, weak C-H⋯π inter-actions and π-π stacking inter-actions [centroid-centriod distances = 3.832 (4) and 3.850 (5) Å] contribute to the stabilization of the crystal structure.

12 CFR 563g.8 - Use of the offering circular.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Use of the offering circular. 563g.8 Section 563g.8 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY SECURITIES OFFERINGS § 563g.8 Use of the offering circular. (a) An offering circular or amendment declared effective by the...

Electrochemical characterisation of X10CrNi 18-8 steel in artificial plasma

Directory of Open Access Journals (Sweden)

J. Przondziono

2015-01-01

Full Text Available Quality of applied guide wires conditions the course of treatment and its success to a great extent. In order to simulate conditions that can be found in blood vascular system samples were exposed to artificial blood plasma (T = 37 } 1 oC for the time of 8 h. In order to obtain information regarding physical and chemical properties of modified surface of wire made of X10CrNi 18-8 steel, electrochemical impedance spectroscopy (EIS test and tests of chemical composition of the surface layer X-ray photoelectron spectroscopy (XPS were made. On the ground of performed EIS and XPS tests, favourable impact of steam sterilisation process on corrosion resistance of X10CrNi 18-8 steel was observed only for the case when chemical passivation was applied prior to sterilisation.

7Li(18O, 17N8Be reaction and the 17N + 8Be-potential

Directory of Open Access Journals (Sweden)

A. T. Rudchik

2010-12-01

Full Text Available Angular distributions of the 7Li(18O, 17N8Be reaction were measured for the transitions to the ground states of 8Be and 17N and excited states of 17N at the energy Elab(18O = 114 MeV. The data were analyzed with coupled-reaction-channels method for one- and two-step transfers of nucleons and clusters. In the analysis, the 7Li + 18O potential de-duced in the analysis of the elastic 7Li + 18O-scattering data as well as shell-model spectroscopic amplitudes of trans-ferred nucleons and clusters were used. Parameters of the 8Be + 17N potential were deduced using the reaction data. Contributions of different one- and two-step transfers in the 7Li(18O, 17N8Be reaction cross-section was studied.

Microstructure of reactive synthesis TiC/Cr18Ni8 stainless steel bonded carbides

Institute of Scientific and Technical Information of China (English)

Jiang Junsheng; Liu Junbo; Wang Limei

2008-01-01

TiC/Cr18Ni8 steel bonded carbides were synthesized by vacuum sintering with mixed powders of iron, ferrotitanium, ferrochromium, colloidal graphite and nickel as raw materials. The microstructure and microhardness of the steel bonded carbides were analyzed by scanning electron microscope (SEM),X-ray diffraction (XRD) and Rockwell hardometer. Results show that the phases of steel bonded carbides mainly consist of TiC and Fe-Cr-Ni solid solution. The synthesized TiC particles are fine. Most of them are not more than 1 μm With the increase of sintering temperature, the porosity of TiC/Cr18Ni8 steel bonded carbides decreases and the density and hardness increase, but the size of TiC panicles slightly increases. Under the same sintering conditions, the density and hardness of steel bonded carbides with C/Ti atomic ratio 0.9 are higher than those with C/Ti atomic ratio 1.0.The TiC particles with C/Ti atomic ratio 0.9 are much finer and more homogeneous.

40 CFR 130.8 - Water quality report.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 21 2010-07-01 2010-07-01 false Water quality report. 130.8 Section... QUALITY PLANNING AND MANAGEMENT § 130.8 Water quality report. (a) Each State shall prepare and submit biennially to the Regional Administrator a water quality report in accordance with section 305(b) of the Act...

40 CFR 35.925-8 - Environmental review.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Environmental review. 35.925-8 Section 35.925-8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GRANTS AND OTHER FEDERAL... Environmental review. (a) That, if the award is for step 2, step 3, or step 2=3, the requirements of the...

Electrochemical impedance spectrometry using Inconel 690, zircaloy 4, 316Ti steel, 17-4-PH, UR52N et URSB8. Simulation in tritiated water. Tome 1

International Nuclear Information System (INIS)

Bellanger, G.

1994-11-01

The redox potential of 3 H 2 O, as well as the corrosion potentials in this medium are found, abnormally, in the trans-passive region. This is completely different from the behavior in the chemical industry or in the water in nuclear powers. With such behavior, there will be breakdowns of the protective oxide layers, and in the presence of chloride there will be immediate pitting. Polarization and electrochemical impedance spectrometry curves are presented and discussed. These curves make it possible to ascertain the corrosion domains and to compare the kinetics of different stainless alloys. These corrosion kinetics and the corrosion potentials provide a classification of the steels studied here: Inconel 690, zircaloy 4, 316 Ti steel, 17-4-PH, UR52N et URSB8. From the results it can be concluded that URSB8 has the best corrosion resistance. (author). 279 figs., tabs

On superplasticity of corrosion resistant ferritic-austenitic chromium-nickel steels

Energy Technology Data Exchange (ETDEWEB)

Surovtsev, A P; Sukhanov, V E

1988-01-01

The deformability of corrosion resistant chromium-nickel ferritic austenitic steel type O8Kh22N6T under tension, upsetting and torsion in the 600-1200 deg C temperature range is studied. For the deformation rate of the order of 10/sup -3/ s/sup -1/ the effect of superelasticity reveals itself at 850 deg C in the process of ferrite dynamic polymerization, in the 925-950 deg C range, at initial stages of dynamic recrystallization - the dynamic polygonization controlled by chromium carbide dissolving in steel and maximum at 1050 deg C in the process of development of austenite dynamic recrystallization with grain refinement with F/A ratio equalling 1. After upsetting in the elasticity mode at 1050 deg C the impact strength of the above steel is maximum.

Wetting behavior of molten In-Sn alloy on bulk amorphous and crystalline Cu40Zr44Al8Ag8

International Nuclear Information System (INIS)

Ma, G. F.; Zhang, H. F.; Li, H.; Hu, Z. Q.

2007-01-01

Using the sessile-drop method, the wettability of the molten In-Sn alloy on bulk amorphous and crystalline Cu 40 Zr 44 Al 8 Ag 8 alloy was studied at different temperatures. It was found that the equilibrium contact angle of In-Sn alloy melt on bulk amorphous substrate was smaller than that of the crystalline one. An intermetallic compound existed at the interface of In-Sn alloy on amorphous Cu 40 Zr 44 Al 8 Ag 8 , while no intermediate reaction layer was formed at the interface of In-Sn alloy on crystalline Cu 40 Zr 44 Al 8 Ag 8 in the temperature range studied

Radiolabeling of multimeric neurotensin(8-13) analogs with the short-lived positron emitter fluorine-18.

Science.gov (United States)

Hultsch, Christina; Berndt, Mathias; Bergmann, Ralf; Wuest, Frank

2007-07-01

Three methods for (18)F-labeling of dimeric and tetrameric neurotensin(8-13) derivatives were evaluated with respect to the labeling yield and the required peptide amounts. Labeling using N-succinimidyl-4-[(18)F]fluorobenzoate ([(18)F]SFB) gave low radiochemical yield for the dimeric peptides. Coupling of the tetramer with [(18)F]SFB was not successful. High yields were obtained for labeling of the aminooxy-functionalized neurotensin(8-13) dimer using 4-[(18)F]fluorobenzaldehyde ([(18)F]FBA) whilst coupling of the corresponding tetramer gave only low yields. Labeling of sulfydryl-functionalized neurotensin(8-13) derivatives using the maleinimide 4-[(18)F]fluorobenzaldehyde-O-[6-(2,5-dioxo-2,5-dihydro-pyrrol-1-yl)-hexyl]-oxime ([(18)F]FBAM) resulted in high radiochemical yields for both, the dimer and the tetramer. Therefore, [(18)F]FBAM seems to be the most suitable (18)F-labeling agent for multivalent neurotensin(8-13) derivatives.

Radiolabeling of multimeric neurotensin(8-13) analogs with the short-lived positron emitter fluorine-18

Energy Technology Data Exchange (ETDEWEB)

Hultsch, Christina [Institute of Radiopharmacy, Research Center Rossendorf, P.O. Box 51 01 19, D-01314 Dresden (Germany); Berndt, Mathias [Institute of Radiopharmacy, Research Center Rossendorf, P.O. Box 51 01 19, D-01314 Dresden (Germany); Bergmann, Ralf [Institute of Radiopharmacy, Research Center Rossendorf, P.O. Box 51 01 19, D-01314 Dresden (Germany); Wuest, Frank [Institute of Radiopharmacy, Research Center Rossendorf, P.O. Box 51 01 19, D-01314 Dresden (Germany)

2007-07-15

Three methods for {sup 18}F-labeling of dimeric and tetrameric neurotensin(8-13) derivatives were evaluated with respect to the labeling yield and the required peptide amounts. Labeling using N-succinimidyl-4-[{sup 18}F]fluorobenzoate ([{sup 18}F]SFB) gave low radiochemical yield for the dimeric peptides. Coupling of the tetramer with [{sup 18}F]SFB was not successful. High yields were obtained for labeling of the aminooxy-functionalized neurotensin(8-13) dimer using 4-[{sup 18}F]fluorobenzaldehyde ([{sup 18}F]FBA) whilst coupling of the corresponding tetramer gave only low yields. Labeling of sulfydryl-functionalized neurotensin(8-13) derivatives using the maleinimide 4-[{sup 18}F]fluorobenzaldehyde-O-[6-(2,5-dioxo-2,5-dihydro-pyrrol-1-yl)-hexyl] -oxime ([{sup 18}F]FBAM) resulted in high radiochemical yields for both, the dimer and the tetramer. Therefore, [{sup 18}F]FBAM seems to be the most suitable {sup 18}F-labeling agent for multivalent neurotensin(8-13) derivatives.

Radiolabeling of multimeric neurotensin(8-13) analogs with the short-lived positron emitter fluorine-18

International Nuclear Information System (INIS)

Hultsch, Christina; Berndt, Mathias; Bergmann, Ralf; Wuest, Frank

2007-01-01

Three methods for 18 F-labeling of dimeric and tetrameric neurotensin(8-13) derivatives were evaluated with respect to the labeling yield and the required peptide amounts. Labeling using N-succinimidyl-4-[ 18 F]fluorobenzoate ([ 18 F]SFB) gave low radiochemical yield for the dimeric peptides. Coupling of the tetramer with [ 18 F]SFB was not successful. High yields were obtained for labeling of the aminooxy-functionalized neurotensin(8-13) dimer using 4-[ 18 F]fluorobenzaldehyde ([ 18 F]FBA) whilst coupling of the corresponding tetramer gave only low yields. Labeling of sulfydryl-functionalized neurotensin(8-13) derivatives using the maleinimide 4-[ 18 F]fluorobenzaldehyde-O-[6-(2,5-dioxo-2,5-dihydro-pyrrol-1-yl)-hexyl] -oxime ([ 18 F]FBAM) resulted in high radiochemical yields for both, the dimer and the tetramer. Therefore, [ 18 F]FBAM seems to be the most suitable 18 F-labeling agent for multivalent neurotensin(8-13) derivatives

Radiochemical studies relevant to the production of sup 8 sup 6 Y and sup 8 sup 8 Y at a small-sized cyclotron

CERN Document Server

Kettern, K; Spellerberg, S; Coenen, H H; Qaim, S M

2002-01-01

Excitation functions were measured by the stacked-foil technique for sup n sup a sup t Sr(p,xn) sup 8 sup 8 sup , sup 8 sup 7 sup m sup , sup g Y reactions from threshold up to 25 MeV. From the measured cross sections integral yields of sup 8 sup 8 Y, sup 8 sup 7 mY and sup 8 sup 7 sup g Y were calculated. The optimum energy range for the production of sup 8 sup 8 Y is Ep=14->9 MeV; the sup 8 sup 8 Y yield amounts to 1.75 MBq (47.3 mu Ci/mu A.h) and the sup 8 sup 7 Y and sup 8 sup 7 sup m Y impurities to 2.0 and 4.4%, respectively. The isomeric cross section ratio for the pair sup 8 sup 7 sup m sup , sup g Y was determined as a function of incident proton energy and the results are discussed in terms of the spins of the two isomeric states involved. Medium scale production of both sup 8 sup 6 Y and sup 8 sup 8 Y has been carried out more than 15 times each using the (p,n) reaction. In the former case 96.3% enriched sup 8 sup 6 SrCO sub 3 was used as target material, and in the latter sup n sup a sup t SrCO su...

Ab initio studies of vacancies in (8,0) and (8,8) single-walled carbon and boron nitride nanotubes

CSIR Research Space (South Africa)

Mashapa, MG

2012-09-01

Full Text Available -1 Journal of Nanoscience and Nanotechnology Vol. 12, 7030?7036, 2012 Ab Initio Studies of Vacancies in (8,0) and (8,8) Single-Walled Carbon and Boron Nitride NanotubesAb M. G. Mashapa 1, 2, *, N. Chetty 2, and S. Sinha Ray 1, 3 1 DST...

Hot deformation effect on the kinetics of austenite transformation under continuous cooling conditions

International Nuclear Information System (INIS)

Bernshtejn, M.L.; Zajmovskij, V.A.; Kisteh, N.V.; Samedov, O.V.; Faldin, S.A.

1979-01-01

The effect of hot deformation on the kinetics of austenite transformations in the commercial 4040Kh 40KhN, and 40KhNMA steels on continuous cooling was studied. The transformations were studied using a dilatometer of a special design which permits a specimen to be fixed quickly in holders after hot deformation. It is stated that in hot-deformed austenite the pearlite transformation proceeds at higher temperatures and in a narrower temperature range. Austenite deformation provides an opportunity to obtain a more fine ferrite-pearlite structure and ensures a uniform distribution of a structurally free ferrite in the steel bulk. The effect of hot deformation on the structure of ferrite decomposition products in the 40KhN and 40KhNMA steels is more complicated, which is connected with a substantial change in the kinetics of pearlite and intermediate transformations

Inhibition of salt precipitation, corrosion and corrosion fatigue of steel in neutral environments

International Nuclear Information System (INIS)

Mikhajlovskij, V.Ya.; Slobodyan, Z.V.; Soprunyuk, N.G.; Ivanov, A.M.

1983-01-01

Processes of salt precipitation, corrosion under dynamic and static conditions, are studied as well as corrosion fatigue of 20 and 40Kh steels in neutral aqueous media without and with the addition of compounds of several classes. The solution of calcium bicarbonate with the initial concentration [Ca(HCO 3 ) 2 ]=1.3 g/l and 3% NaCl solution in distilled water are used for investigation. The effectiveness index of salt precipitation inhibitor is determined by the change in the rate of calcium bicarbonate transformation into carbonate. The combination of results obtained permits to make the conclusion that tripolyphosphate and pyrophosphoric acid are rather perspective inhibitors of complex effect with low protective concentrations

Estimation of cross sections of hypotetical 8n0, 10He2, 13Li3 nuclei production in the framework of fast fragmentation model

International Nuclear Information System (INIS)

Lozhkin, O.V.; Oplavin, V.S.; Yakovlev, Yu.P.

1983-01-01

The possibilities of search for 8 n 0 , 10 He 2 , 13 Li 3 nuclides in the products of nuclear fragmentation under the action of high energy particles are analysed. Conclusions have been drawn that: available experimental data on determination of the upper boundary of a cross section of 8 n 0 fragments production exclude an existence of this nuclide in the form ''usual'' nuclear system; available experimental estimations of cross sections of 10 He and 13 Li production among fragmentation products are, for the present, insufficient to solve a problem of 13 Li nucleus existence in a bound state but testify on 10 He nucleus nuclear instability; serious model estimations of have functions and nuclide binding energy are necessary

Progress with Implementing Energy Efficiency Policies in the G8

Energy Technology Data Exchange (ETDEWEB)

NONE

2009-07-01

At the 2008 G8 Summit in Hokkaido, leaders reaffirmed the critical role improved energy efficiency can play in addressing energy security, environmental and economic objectives. They went even farther than in previous Summits and committed to maximising implementation of the 25 IEA energy efficiency recommendations prepared for the G8. The imperative to enhance energy efficiency remains a priority for all countries. To support governments with their implementation of energy efficiency, the IEA recommended the adoption of a broad range of specific energy efficiency policy measures to the G8 Summits in 2006, 2007 and 2008. The consolidated set of recommendations from these Summits covers 25 fields of action across seven priority areas: cross-sectoral activity, buildings, appliances, lighting, transport, industry and power utilities. If governments want to significantly improve energy efficiency, the IEA considers that no single policy implemented in isolation will be effective at achieving this aim. The IEA Secretariat recommends that governments implement a full set of appropriate measures. The IEA estimates that if implemented globally without delay, the proposed actions could save around 8.2 GtCO2/yr by 2030 -- equivalent to twice the EU's yearly emissions. This report evaluates the progress of the G8 countries in implementing energy efficiency policy, including the 25 G8/IEA recommendations. Information in this report is current up to 31 March 2009.

Características de las fallas en alimentadores de 13,8 kV del sistema soterrado de La Habana;Characteristic of 13,8 kV feeders faults of the Havana underground system

Directory of Open Access Journals (Sweden)

Boris Alba - Valle

2011-06-01

Full Text Available El sistema soterrado de La Habana enfrenta problemas de continuas fallas en sus alimentadores de 13,8 kV. En este trabajo se determinan las características de estas averías, en el período comprendido entre los años 2007 y 2009, y se proponen algunas medidas objetivas con el fin de contribuir a su disminución. La investigación se basó fundamentalmente en el estudio de la base de datos de los alimentadores de 13,8 kV proporcionada por el departamento técnico de la Unidad Empresarial Básica (UEB Soterrada y en el uso de herramientas estadísticas digitales. Como resultado se pudo constatar que las fallas son más frecuentes en los alimentadores de la subestación de Tallapiedra producto de la humedad en cables y empalmes con aislamiento de PILC (papel impregnado en aceite y con cubierta de plomo, dispuestos por tierra muerta. Finalmente, las medidas propuestas tuvieron un impacto positivo en la disminución de estas fallas, en un período inferior a un año.The Havana underground system has problems of continuous faults in their 13,8 kV feeders. In this article the characteristics of these mishaps in the period of 2007 to 2009 are determined and purpose some objective measurements with the end of contributing to their decrease. The investigation was fundamentally based on the study of the 13,8 kV feeders database proportioned by the technical department of the Underground Basic Managerial Unit (UEB and the use of digital statistical tools. As a result, it was verified that the faults occur with more frequency in the Tallapiedra substation feeders, due to the humidity in cables and connections with PILC isolation (impregnated in oil and lead covered paper, prepared for undergrounding directly in the earth. Finally, the proposed measures had a positive impact in the decrease of these faults, in a period less than to a year.

Chemical heat treatment of low alloyed maraging steels

Energy Technology Data Exchange (ETDEWEB)

Malinov, L S; Korotich, I K [Zhdanovskij Metallurgicheskij Inst. (Ukrainian SSR)

1979-09-01

The investigation concerned the nitriding, cementation, chromizing, borating of economically alloyed maraging grade 04Kh2N5MFYu steel. The investigated methods of chemothermal treatment were found to considerably increase the hardness of the surface layer of the maraging steel. The high tempering of the grade 04Kh2N5MFYu cemented and hardened steel was found to produce secondary hardening. On chromizing, the diffusion layer is an alloyed ferrite which strengthens because of the dispersion hardening on ageing. The formation of the plastic low-carbon martensite at relatively small cooling rates greatly decreases the tendency of the boride layer to cracking.

Excellent mechanical properties and resistance to cavitation erosion for an ultra-low carbon CrMnN stainless steel through quenching and partitioning treatment

Science.gov (United States)

Zhou, Ze-an; Fu, Wan-tang; Zhu, Zhe; Li, Bin; Shi, Zhong-ping; Sun, Shu-hua

2018-05-01

The retained austenite content (RAC), the mechanical properties, and the resistance to cavitation erosion (CE) of the 00Cr13Mn8MoN steel after quenching and partitioning (Q&P) processing were investigated. The results show that the Q&P process affected the RAC, which reached the maximum value after partitioning at 400°C for 10 min. The tensile strength of the steel slightly decreased with increasing partitioning temperature and time. However, the elongation and product of strength and elongation first increased and then decreased. The sample partitioned at 400°C for 10 min exhibited the optimal property: a strength-ductility of 23.8 GPa·%. The resistance to CE for the 00Cr13Mn8MoN steel treated by the Q&P process was improved due to work hardening, spalling, and cavitation-induced martensitic transformation of the retained austenite.

Metallurgic study of the steel Z8CDWV12

Energy Technology Data Exchange (ETDEWEB)

Loier, C.; Ottmann, M.C.; Risacher, R.; Leymonie, C.

1984-01-01

Steel Z8CDWV12 has a duplex structure showing ferrite and carbide-rich areas. It is used by Alsthom-Atlantique for making steam turbine nozzles. CCT diagram was plotted and enabled carbide-rich areas transformations to be understood. It was demonstrated that treatments commonly called temperings were in fact intercritical treatments. The variation of tensile and impact properties was determined as a function of the initial quenching rate and of intercritical treatment temperature. Results enable convenient heat treatments to be determined as a function of plate thickness.

40 CFR 305.8 - Examination of documents filed.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 27 2010-07-01 2010-07-01 false Examination of documents filed. 305.8 Section 305.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SUPERFUND, EMERGENCY... Examination of documents filed. (a) Inspection of Documents. Subject to the provisions of law restricting...

On unitary representations of the exceptional non-linear N=7 and N=8 superconformal algebras in terms of free fields

International Nuclear Information System (INIS)

Ketov, S.V.

1996-01-01

The simplest free-field realizations of the exceptional non-linear (quadratically generated, or W-type) N=8 and N=7 superconformal algebras with Spin(7) and G 2 affine currents, respectively, are investigated. Both the N=8 and N=7 algebras are found to admit unitary and highest-weight irreducible representations in terms of a single free boson and free fermions in 8 of Spin(7) or 7 of G 2 , respectively, at level k=1 and the corresponding central charges c 8 =26/5 and c 7 =5. (orig.)

X-ray spectrum microanalysis of copper and stainless steel surface layer after electroerosion machining

International Nuclear Information System (INIS)

Abdukarimov, Eh.T.; Saidinov, S.Ya.

1989-01-01

The results of experimental investigations of the surface layer of copper and steel 12Kh18N10T after electroerrosion treatment by a rotating tungsten electrode in natural and distilled water are presented. It is established that the quantity of electrode material transferred to the surface of the steel treated grows with the spark discharge energy increase. Tungsten concentration in the surface layer reaches 5-10% with the average depth of penetration 40-50 μm

Metastable structure formation during high velocity grinding

International Nuclear Information System (INIS)

Samarin, A.N.; Klyuev, M.M.

1984-01-01

Metastable structures in surface layers of samples are; investigated during force high-velocity abrasive grinding. Samples of martensitic (40Kh13), austenitic (12Kh18N10T), ferritic (05Kh23Yu5) steels and some alloys, in particular KhN77TYuR (EhI437B), were grinded for one pass at treatment depth from 0.17 up to 2.6 mm. It is established that processes of homogenizing, recrystallization and coagulation are; developed during force high-velocity grinding along with polymorphic transformations in the zone of thermomechanical effect, that leads to changes of physical and mechanical properties of the surface

More gaugings of N=8 supergravity

International Nuclear Information System (INIS)

Hull, C.M.

1984-01-01

New non-compact gaugings of N = 8 supergravity are constructed. The gauge groups are SO(p,q) (with p + q = 8) and the group contraction of SO(p,q) about SO(p). The SO(4,4) gauging and the corresponding contraction truncate to gauged N = 4 supergravity theories. (orig.)

Carbon steel protection in G.S. [Girldler sulphide] plants: Pt. 8

International Nuclear Information System (INIS)

Lires, Osvaldo; Delfino, Cristina; Rojo, Enrique.

1990-01-01

In order to protect carbon steel of towers and piping of a GS experimental heavy water plant against corrosion produced by the action of aqueous solutions of hydrogen sulphide, a method, elsewhere published, was developed. Carbon steel exposed to saturated aqueous solutions of hydrogen sulphide forms iron sulphide scales. In oxygen free solutions, evolution of corrosion follows the sequence mackinawate → cubic ferrous sulphide → troilite → pyrrotite → pyrite. Scales formed by pyrrotite and pyrite are the most protective layers (these are obtained at 130 deg C, 2 MPa for a period of 14 days). Pyrite formation is favoured by an oxidizing agent presence that allows the oxidation of sulphur ions to disulphur ions. Elemental sulphur or oxygen were used as oxidating agents. Variation and operational parameters such as concentration, temperature, pH, aggregate time, etc. were studied. Though little improvement on protective scales quality was observed, results do not justify operational troubles and the additional costs and effort involved. (Author)

Unit rupture work as a criterion for quantitative estimation of hardenability in steel

International Nuclear Information System (INIS)

Kramarov, M.A.; Orlov, E.D.; Rybakov, A.B.

1980-01-01

Shown is possible utilization of high sensitivity of resistance to fracture of structural steel to the hardenability degree in the course of hardening to find the quantitative estimation of the latter one. Proposed is a criterion kappa, the ratio of the unit rupture work in the case of incomplete hardenability (asub(Tsub(ih))) under investigation, and the analoguc value obtained in the case of complete hardenability Asub(Tsub(Ch)) at the testing temperature corresponding to the critical temperature Tsub(100(M). Confirmed is high criterion sensitivity of the hardened steel structure on the basis of experimental investigation of the 40Kh, 38KhNM and 38KhNMFA steels after isothermal hold-up at different temperatures, corresponding to production of various products of austenite decomposition

El discurso hegemónico sobre las acciones colectivas de resistencia civil: Casos comunas 8, 9 y 13 de Medellín The Hegemonic Discourse about Collective Actions of Civil Resistance: Cases Communes 8, 9 and 13 of Medellín

OpenAIRE

Mary Luz Alzate Zuluaga

2010-01-01

En este artículo se discute la manera cómo en la prensa escrita son informadas las distintas expresiones de resistencia civil, a partir del rastreo de la información registrada en la prensa escrita local y nacional acerca de los casos de las Comunas 8, 9 y 13 de la ciudad de Medellín durante los años 2002-2006. Se busca conocer así, de qué modo han sido descritas e interpretadas dichas prácticas, cuáles son las ausencias y los aspectos subrayados con lo emitido, qué relaciones de poder se leg...

N=8 supersingleton quantum field theory

International Nuclear Information System (INIS)

Bergshoeff, E.; Salam, A.; Sezgin, E.; Tanii, Yoshiaki.

1988-06-01

We quantise the N=8 supersymmetric singleton field theory which is formulated on the boundary of the four dimensional anti de Sitter spacetime (AdS 4 ). The theory has rigid OSp(8,4) symmetry which acts as a superconformal group on the boundary of AdS 4 . We show that the generators of this symmetry satisfy the full quantum OSp(8,4) algebra. The spectrum of the theory contains massless states of all higher integer and half-integer spin which fill the irreducible representations of OSp(8,4) with highest spin s max =2,4,6,... Remarkably, these are in one to one correspondence with the generators of Vasiliev's infinite dimensional extended higher spin superalgebra shs(8,4), suggesting that we may have stumbled onto a field theoretic realization of this algebra. We also discuss the possibility of a connection between the N=8 supersingleton theory with the eleven dimensional supermembrane in an AdS 4 xS 7 background. (author). 34 refs

Chromium surface alloying of structural steels during laser treatment

International Nuclear Information System (INIS)

Kurov, I.E.; Nagornykh, S.N.; Sivukhin, G.A.; Solenov, S.V.

1987-01-01

Results of matrix alloying from the surface layer and creation of considerably increased chromium concentration in the depth which permits to increase the efficiency of laser treatment of steels (12Kh18N10T and 38KhN3M) in the process of their further mechanical polishing, are presented. The treatment was realized by continuous CO 2 -laser at different power densities and scanning rates are presented. A model describing the creation of anomalous distributions of the alloying element in steels is plotted

Influence of corrosion environment composition on crack propagation in high-strength martensitic steel

International Nuclear Information System (INIS)

Romaniv, O.N.; Nikiforchin, G.N.; Tsirul'nik, A.T.

1984-01-01

The 40 Kh steel is taken as an example to investigate the dependence of electrochemical parameters in the crack tip and characteristics of corrosion static cracking resistance of martensitic steel on the composition of environment. The tests are performed in acidic and alkaline solutions prepared by adding HC or NaOH in distilled water. It is established that growth of pH value of initial solutions trom 0 to 13 brings about linear increase of a threshold stress intensity factor. It is found that acidic medium in the crack tip preserves up to pH 13 of initial medium. The possibility of corrosion crack propagation in alkaline solutions according to the mechanism of hydrogen embrittlement is proved

Phytosterol Feeding Causes Toxicity in ABCG5/G8 Knockout Mice

Science.gov (United States)

McDaniel, Allison L.; Alger, Heather M.; Sawyer, Janet K.; Kelley, Kathryn L.; Kock, Nancy D.; Brown, J. Mark; Temel, Ryan E.; Rudel, Lawrence L.

2014-01-01

Plant sterols, or phytosterols, are very similar in structure to cholesterol and are abundant in typical diets. The reason for poor absorption of plant sterols by the body is still unknown. Mutations in the ABC transporters G5 and G8 are known to cause an accumulation of plant sterols in blood and tissues (sitosterolemia). To determine the significance of phytosterol exclusion from the body, we fed wild-type and ABCG5/G8 knockout mice a diet enriched with plant sterols. The high-phytosterol diet was extremely toxic to the ABCG5/G8 knockout mice but had no adverse effects on wild-type mice. ABCG5/G8 knockout mice died prematurely and developed a phenotype that included high levels of plant sterols in many tissues, liver abnormalities, and severe cardiac lesions. This study is the first to report such toxic effects of phytosterol accumulation in ABCG5/G8 knockout mice. We believe these new data support the conclusion that plant sterols are excluded from the body because they are toxic when present at high levels. PMID:23380580

16 CFR Appendix G8 to Part 305 - Boilers-Electric

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Boilers-Electric G8 Appendix G8 to Part 305 Commercial Practices FEDERAL TRADE COMMISSION REGULATIONS UNDER SPECIFIC ACTS OF CONGRESS RULE CONCERNING... Part 305—Boilers—Electric Manufacturer's rated heating capacities (Btu's/hr.) Range of annual fuel...

Functionalization of SU-8 photoresist surfaces with IgG proteins

International Nuclear Information System (INIS)

Blagoi, Gabriela; Keller, Stephan; Johansson, Alicia; Boisen, Anja; Dufva, Martin

2008-01-01

The negative epoxy-based photoresist SU-8 has a variety of applications within microelectromechanical systems (MEMS) and lab-on-a-chip systems. Here, several methods to functionalize SU-8 surfaces with IgG proteins were investigated. Fluorescent labeled proteins and fluorescent sandwich immunoassays were employed to characterize the binding efficiency of model proteins to bare SU-8 surface, SU-8 treated with cerium ammonium nitrate (CAN) etchant and CAN treated surfaces modified by aminosilanization. The highest binding capacity of antibodies was observed on bare SU-8. This explains why bare SU-8 in a functional fluorescent sandwich immunoassay detecting C-reactive protein (CRP) gave twice as high signal as compared with the other two surfaces. Immunoassays performed on bare SU-8 and CAN treated SU-8 resulted in detection limits of CRP of 30 and 80 ng/ml respectively which is sufficient for detecting CRP in clinical samples, where concentrations of 3-10 μg/ml are normal for healthy individuals. In conclusion, bare SU-8 and etched SU-8 can be modified with antibodies by a simple adsorption procedure which simplifies building lab-on-a-chip systems in SU-8. Additionally, we report the fabrication process and use of microwells created in a SU-8 layer with the same dimensions as a standard microscope glass slide that could fit into fluorescent scanners. The SU-8 microwells minimize the reagent consumption and are straightforward to handle compared to SU-8 coated microscope slides

Parametrical limits of SCC-susceptibility of austenitic and austenitic-ferritic Cr-Ni steels

International Nuclear Information System (INIS)

Starosvetskij, D.I.; Baru, R.L.; Bondarenko, A.I.; Bogoyavlenskij, V.L.; Timonin, V.A.

1990-01-01

Comparative investigations into corrosion cracking (CC) of austenitic (12Kh18N10T) and austenitic-ferritic (08Kh22N6T) chromium-nickel steels are performed for various chloride media in a wide range of chloride concentrations and temperatures. It is shown that the ratio between steels in terms of their CC-susceptibility is not definite and can undergo a reversal depending on parameters of medium, level and conditions of loading. Differences in mechanisms of corrosion cracking of austenitic and austenitic-ferritic steels are established

Evaluation of the degradation characteristics of CF-8A cast stainless steel using EDS and nano-indentation

International Nuclear Information System (INIS)

Baek, Seung; Koo, Jae Mean; Seok, Chang Sung

2004-01-01

Cast austenitic stainless steel piping pump, valve casings, and elbows are susceptible to reductions in toughness and ductility because of long term exposure at the operating temperatures in LWR(Light Water Reactor). In this paper, we have measured the material properties of long term aged CF-8A cast stainless steel, accelerated aging at 400 .deg. C. These studies have been carried out using indentation tests(automated ball indentation and nano-indentation) and EDS(Energy Dispersive Spectroscopy). The fracture toughness of Cf-8A cast stainless steel was also determined by using standard fracture toughness and automated ball indentation

Ultrathin g-C3N4 films supported on Attapulgite nanofibers with enhanced photocatalytic performance

Science.gov (United States)

Xu, Yongshuai; Zhang, Lili; Yin, Minghui; Xie, Dengyu; Chen, Jiaqi; Yin, Jingzhou; Fu, Yongsheng; Zhao, Pusu; Zhong, Hui; Zhao, Yijiang; Wang, Xin

2018-05-01

A novel visible-light-responsive photocatalyst is fabricated by introducing g-C3N4 ultrathin films onto the surface of attapulgite (ATP) via a simple in-situ depositing technique, in which ATP was pre-grafted using (3-Glycidyloxypropyl) trimethoxysilane (KH560) as the surfactant. A combination of XRD, FT-IR, BET, XPS, UV-vis, TEM and SEM techniques are utilized to characterize the composition, morphology and optical properties of the products. The results show that with the help of KH560, g-C3N4 presented as ultrathin layer is uniformly loaded onto the surface of ATP by forming a new chemical bond (Sisbnd Osbnd C). Comparing with g-C3N4 and ATP, ATP/g-C3N4 exhibits remarkably enhanced visible-light photocatalytic activity in degradation of methyl orange (MO) because of its high surface area, appropriate band gap and the synergistic effect between g-C3N4 and ATP. To achieve the best photocatalyst, the ratio of g-C3N4 was adjusted by controlling the mass portion between ATP-KH560 and melamine (r = m (ATP-KH560)/m (melamine)). The highest decomposition rate of methyl orange (MO) was 96.06% when r = 0.5 and this degradation efficiency remained unchanged after 4 cycles, which is 10 times as that of pure g-C3N4 particles. Possible photocatalytic mechanism is presented.

Influence of surface mechanical activation of the X40Cr13 steel on roughness after ion and gas nitriding

International Nuclear Information System (INIS)

Jasinski, J.; Wojtal, A.; Jeziorski, L.; Radecki, A.; Ucieklak, S.

2003-01-01

The article describes the problem of the thermal and mechanical activation of the surface of the X40Cr13 steel on the state of the ion and gas nitriding. in order to determine the nitriding influence and make the analysis of results, the steel was subjected to: soft annealing, hardening with subsequent tempering at T = 550 o C and also mechanical activation of the surface consisting in peripheral grinding with abrasive papers of the grain size 60, 360, 1000 and mechanical polishing. The main aim of this work was to establish the influence of different surface geometrical structure, depending on X40Cr13 steel structure, on the roughness profile after ion and gas nitriding. With regard to the above, the examinations of basic roughness parameters prior to and after thermochemical processes and the analysis of utilitarian usefulness of activations applied were carried out. (author)

Plasticity of low carbon stainless steels

International Nuclear Information System (INIS)

Bulat, S.I.; Fel'dgandler, Eh.G.; Kareva, E.N.

1975-01-01

In the temperature range 800-1200 0 C and with strain rates of from 10 -3 to 3 s -1 , austenitic (000Kh18N12) and austenitic-ferrite (000Kh26N6) very low carbon stainless steels containing 0.02-0.03% C exhibit no higher resilience than corresponding ordinary steels containing 0.10-0.12% C. However, the plasticity of such steels (particularly two-phase steels) at 900-1100 0 C is appreciably inferior owing to the development of intergranular brittle fracture. Pressure treatment preceded by partial cooling of the surface to 850 0 C yields rolled and forged products with acceptable indices but is inconvenient technically. At the Zlatoustovsk and Ashin metallurgical plants successful tests have been performed involving the forging and rolling of such steels heated to 1280-1300 0 C without partial cooling; it was necessary to improve the killing conditions, correct the chemical composition (increasing the proportion of ferrite) and take measures against heat loss. (author)

Ocular Hypotensive Response in Nonhuman Primates of (8R)-1-[(2S)-2-Aminopropyl]-8,9-dihydro-7H-pyrano[2,3-g]indazol-8-ol a Selective 5-HT2 Receptor Agonist.

Science.gov (United States)

May, Jesse A; Sharif, Najam A; McLaughlin, Marsha A; Chen, Hwang-Hsing; Severns, Bryon S; Kelly, Curtis R; Holt, William F; Young, Richard; Glennon, Richard A; Hellberg, Mark R; Dean, Thomas R

2015-11-25

Recently, it has been reported that 5-HT2 receptor agonists effectively reduce intraocular pressure (IOP) in a nonhuman primate model of glaucoma. Although 1-[(2S)-2-aminopropyl]indazol-6-ol (AL-34662) was shown to have good efficacy in this nonhuman primate model of ocular hypertension as well as a desirable physicochemical and permeability profile, subsequently identified cardiovascular side effects in multiple species precluded further clinical evaluation of this compound. Herein, we report selected structural modifications that resulted in the identification of (8R)-1-[(2S)-2-aminopropyl]-8,9-dihydro-7H-pyrano[2,3-g]indazol-8-ol (13), which displayed an acceptable profile to support advancement for further preclinical evaluation as a candidate for proof-of-concept studies in humans.

Engineering Nanowire n-MOSFETs at L_{g}<8 nm

Science.gov (United States)

Mehrotra, Saumitra R.; Kim, SungGeun; Kubis, Tillmann; Povolotskyi, Michael; Lundstrom, Mark S.; Klimeck, Gerhard

2013-07-01

As metal-oxide-semiconductor field-effect transistors (MOSFET) channel lengths (Lg) are scaled to lengths shorter than Lg<8 nm source-drain tunneling starts to become a major performance limiting factor. In this scenario a heavier transport mass can be used to limit source-drain (S-D) tunneling. Taking InAs and Si as examples, it is shown that different heavier transport masses can be engineered using strain and crystal orientation engineering. Full-band extended device atomistic quantum transport simulations are performed for nanowire MOSFETs at Lg<8 nm in both ballistic and incoherent scattering regimes. In conclusion, a heavier transport mass can indeed be advantageous in improving ON state currents in ultra scaled nanowire MOSFETs.

New gauged N = 8, D = 4 supergravities

International Nuclear Information System (INIS)

Hull, C M

2003-01-01

New gaugings of four-dimensional N = 8 supergravity are constructed, including one which has a Minkowski space vacuum that preserves N = 2 supersymmetry and in which the gauge group is broken to SU(3) x U(1) 2 . Previous gaugings used the form of the ungauged action which is invariant under a rigid SL (8,R) symmetry and promoted a 28-dimensional subgroup (SO(8), SO(p, 8 - p) or the non-semi-simple contraction CSO(p, q, 8 - p - q)) to a local gauge group. Here, a dual form of the ungauged action is used which is invariant under SU*(8) instead of SL (8,R) and new theories are obtained by gauging 28-dimensional subgroups of SU*(8). The gauge groups are non-semi-simple and are different real forms of the CSO(2p, 8 - 2p) groups, denoted as CSO*(2p, 8 - 2p), and the new theories have a rigid SU(2) symmetry. The five-dimensional gauged N = 8 supergravities are dimensionally reduced to D = 4. The D = 5, SO(p, 6 - p) gauge theories reduce, after a duality transformation, to the D = 4, CSO(p, 6 - p, 2) gauging while the SO*(6) gauge theory reduces to the D = 4, CSO*(6, 2) gauge theory. The new theories are related to the old ones via an analytic continuation. The non-semi-simple gaugings can be dualized to forms with different gauge groups

Experimental verification of the statistical theories of scaling factor effect in fatigue fracture of steel

International Nuclear Information System (INIS)

Svistun, R.P.; Babej, Yu.I.; Tkachenko, N.N.

1976-01-01

Statistical theories of the scale effect in the fatigue failure of 40KH18N9T, 10 and 20 steels have been verified. The theories are shown to be not invariably suitable for a satisfactory exlanation of the fatigue strength of the samples with respect to their dimensions. One of the main reasons for displaying the scale effect in the process of steel fatigue is the sample self-heating, i.e. a temperature factor which in many cases overlaps a statistical one

Experimental verification of the statistical theories of scaling factor effect in fatigue fracture of steel

Energy Technology Data Exchange (ETDEWEB)

Svistun, R P; Babei, Yu I; Tkachenko, N N [AN Ukrainskoj SSR, Lvov. Fiziko-Mekhanicheskij Inst.; L' vovskij Lesotekhnicheskij Inst. (Ukrainian SSR))

1976-01-01

Statistical theories of the scale effect in the fatigue failure of 40KH18N9T, 10 and 20 steels have been verified. The theories are shown to be not invariably suitable for a satisfactory exlanation of the fatigue strength of the samples with respect to their dimensions. One of the main reasons for displaying the scale effect in the process of steel fatigue is the sample self-heating, i.e. a temperature factor which in many cases overlaps a statistical one.

An experimental study of spider-related covariation bias in 8-to 13-year-old children

NARCIS (Netherlands)

Muris, Peter; de Jong, Peter J.; Meesters, Cor; Waterreus, Bregje; van Lubeck, Janet

2005-01-01

Covariation bias can be defined as phobic subjects' tendency to overestimate the association between phobic stimuli and aversive outcomes. The current study presents two experiments that examined this type of cognitive bias in children aged 8-13 years (N = 147 in Experiment 1, N = 240 in Experiment

Echinococcus canadensis (Cestoda: Taeniidae) is a valid species consisting of the mitochondrial genotypes G6, G7, G8 and G10

Science.gov (United States)

The species status of Echinococcus canadensis has long been controversial, mainly because it consists of the mitochondrial genotypes G6, G7, G8 and G10 with different host affinity: G6 (camel strain) and G7 (pig strain) with domestic cycles and G8 (cervid strain) and G10 (Fennoscandian cervid strain...

Optimal control of conditions of deformation during rolling the bar alloy from alloy steel

International Nuclear Information System (INIS)

Inatovich, Yu.V.; Shilov, V.A.; Shvarts, D.L.; Kudelin, S.P.

2001-01-01

A complex of programs for determining the optimal gaps between rollers during rolling of simple merchant sections of alloy steels of a wide brand assortment (12KhN3A, Kh17N2, Kh18N10T) was elaborated. Experience in calculations made according to the programs suggests advisability of their use in the automated design systems for roller calibration and for adjustment of section mills [ru

Radionuclide imaging of small-cell lung cancer (SCLC) using 99mTc-labeled neurotensin peptide 8-13

International Nuclear Information System (INIS)

Zhang Kaijun; An Rui; Gao Zairong; Zhang Yongxue; Aruva, Mohan R.

2006-01-01

Objectives: To prepare 99m technetium ( 99m Tc)-labeled neurotensin (NT) peptide and to evaluate the feasibility of imaging oncogene NT receptors overexpressed in human small-cell lung cancer (SCLC) cells. Methods: The NT analogue (Nα-His)Ac-NT(8-13) was synthesized such that histidine was attached at the N-terminus. The analogue was labeled with [ 99m Tc(H 2 O) 3 (CO) 3 ] at pH 7. 99m Tc-(Nα-His)Ac-NT(8-13) in vitro stability was determined by challenging it with 100 times the molar excess of DTPA, human serum albumin (HSA) and cysteine. The affinity, 99m Tc-(Nα-His)Ac-NT(8-13) binding to SCLC cell line NCI-H446, was studied in vitro. Biodistribution and imaging with 99m Tc-(Nα-His)Ac-NT(8-13) were performed at 4 and 12 h postinjection, and tissue distribution and imaging after receptor blocking were carried out at 4 h in nude mice bearing human SCLC tumor. Blood clearance was determined in normal mice. Results: The affinity constant (K d ) of 99m Tc-(Nα-His)Ac-NT(8-13) to SCLC cells was 0.56 nmol/L. When challenged with 100 times the molar excess of DTPA, HSA or cysteine, more than 97±1.8% radioactivity remained as 99m Tc-(Nα-His)Ac-NT(8-13). Tumor-to-muscle ratio was 3.35±1.01 at 4 h and 4.20±1.35 at 12 h postinjection. The excretory route of 99m Tc-(Nα-His)Ac-NT(8-13) was chiefly through the renal pathway. In the receptor-blocking group treated with unlabeled (Nα-His)Ac-NT(8-13), tumor-to-muscle ratio at 4 h was 1.25±0.55. Conclusion: The results suggest that 99m Tc-(Nα-His)Ac-NT(8-13) specifically binds to the SCLC cells and made 99m Tc-(Nα-His)Ac-NT(8-13) a desirable compound for further studies in planar or SPECT imaging of oncogene receptors overexpressed in SCLC cells

Crystal structure and optical property of complex perovskite oxynitrides ALi0.2Nb0.8O2.8N0.2, ANa0.2Nb0.8O2.8N0.2, and AMg0.2Nb0.8O2.6N0.4 (A = Sr, Ba)

Science.gov (United States)

Moon, Keon Ho; Avdeev, Maxim; Kim, Young-Il

2017-10-01

Oxynitride type complex perovskites AM0.2Nb0.8O3-xNx (A = Sr, Ba; M = Li, Na, Mg) were newly synthesized by the solid state diffusion of Li+, Na+, or Mg2+ into the layered oxide, A5Nb4O15, with concurrent O/N substitution. Neutron and synchrotron X-ray Rietveld refinement showed that SrLi0.2Nb0.8O2.8N0.2, SrNa0.2Nb0.8O2.8N0.2, and SrMg0.2Nb0.8O2.6N0.4 had body-centered tetragonal symmetry (I4/mcm), while those with A = Ba had simple cubic symmetry (Pm 3 ̅ m). In the tetragonal Sr-compounds, the nitrogen atoms were localized on the c-axial 4a site. However, the octahedral cations, M/Nb (M = Li, Na, Mg) were distributed randomly in all six compounds. The lattice volume of AM0.2Nb0.8O3-xNx was dependent on various factors including the type of A and the electronegativity of M. Compared to the simple perovskites, ANbO2N (A = Sr, Ba), AM0.2Nb0.8O3-xNx had wider band gaps (1.76-2.15 eV for A = Sr and 1.65-2.10 eV for A = Ba), but significantly lower sub-gap absorption.

Tool life equation for blanking 18-8 stainless steel strips

International Nuclear Information System (INIS)

Faura, F.; Lopez, J.; Sanes, J.; Garcia, A.

1998-01-01

Hereinafter it is presented a model for the behaviour and life of circular blanking tool used in sheet forming processes of 18-8 stainless steel (sheet thickness: 1 mm). Frostily it has analyzed the different studies that have previously dealt with this problem. Secondly taking into account recently made experiments, it is proposed a simple formulation to predict tool life with enough reliability. to this purpose it has examined different parameters in the wear process, inferring from these the fundamental parameters that regulate them and about which the different equations have been configurated. Blanking tests were performed using a 20 t press at a speed of 150 strokes/min. Punch materials used in these test were AISI A2 and AISI D2 with diameters between 1.5 and 10 mm. The blanking tests were performed at a clearance between 5 and 20% of the work material thickness. (Author) 8 refs

8-Hydroxydeoxyguanosine in vitro

DEFF Research Database (Denmark)

Fischer-Nielsen, A; Poulsen, H E; Loft, S

1992-01-01

Oxidative DNA damage, as expressed by 8-hydroxydeoxyguanosine (8-OHdG), was investigated in calf thymus DNA exposed to either ultraviolet radiation or to FeCl2/H2O2 in a Fenton-like reaction. The influence of iron (absent in the UV system and present in the FeCl2/H2O2 system) and pH (7.4 and 4.0)...

Efectos gammágenos del cobre en los aceros inoxidables 18Cr8Ni

Directory of Open Access Journals (Sweden)

Botella, J.

1997-10-01

Full Text Available From a series of 22 typical 18Cr8Ni stainless steel 40 kg ingots, with copper variable concentrations from 0.6 to 3.0 weight %, δ-ferrite is measured with a ferrite-meter device, calculating a nickel equivalent of 0.27 for copper. Some differences between the 8-ferrite and that on calculated by DeLong -excluding the copper γ-gene action- have been found because of different solidification and cooling regimes in ingot and weld cases.

A partir de una serie de 22 lingotes de 40 kg de aceros inoxidables típicos 18Cr8Ni, con concentraciones variables de cobre entre 0,6 y 3,0 % en masa, se mide la ferrita δ mediante un medidor de ferrita y se deduce para el cobre un equivalente en níquel de 0,27, a la vez que se establecen ciertas diferencias entre los contenidos de ferrita δ medida y la deducida según DeLong -excluida la acción gammágena del cobre- por el hecho de solidificar en lingotes en vez de la típica solidificación de soldaduras.

Specific features of the occurrence, development, and re-compaction of spall and shear fractures in spherically-convergent shells made of unalloyed iron and some steels under their spherical explosive loading

International Nuclear Information System (INIS)

Kozlov, E.A.; Brichikov, S.A.; Gorbachev, D.M.; Brodova, I.G.; Yablonskikh, T.I.

2007-01-01

Results of comparative metallographic examination of recovered shells exposed to explosive loading in two modes (with and without a heavy casing confining explosion products scatter) are presented. The shells were made of high-purity and technical-grade unalloyed iron with the initial grain size 250 and 125 μm, steel 30KhGSA in delivery state and quenched up to HR C 35...40, austenitic stainless steel 12Kh18N10T. The heavy casing used in experiments is demonstrated to ensure a rather compact convergence of shells destroyed at high radii. In the described comparative experiments, one managed to compile the 12Kh18N10T steel shell, after it was spalled at high radii and exposed to shear fracture and spallation layer fragmentation at medium radii, into a compact sphere but failed to do the same with the 30KhGSA quenched steel shell after it was fractured according to spall and shear mechanisms at high and medium radii. Polar zones of this steel shell have obvious undercompressed areas due to significant dissipative losses to overcome the shear strength. Occurrence, development, and re-compaction of spall and shear fractures in spherically-convergent shells made of materials, which were already carefully investigated in 1D- and 2D-geometry experiments, were systematically studied in order to verify and validate new physical models of dynamic fractures, as well as up-to-date used in 1D-, 2D- and 3D-numerical algorithms [ru

Holographic RG flow in a new SO(3) × SO(3) sector of ω-deformed SO(8) gauged N = 8 $$ \\mathcal{N}=8 $$ supergravity

OpenAIRE

Pang, YiGeorge P. & Cynthia Woods Mitchell Institute for Fundamental Physics and Astronomy, Texas A&M; University, College Station, TX, 77843, U.S.A.; Pope, C.(George P. & Cynthia Woods Mitchell Institute for Fundamental Physics and Astronomy, Texas A&M; University, College Station, TX, 77843, U.S.A.); Rong, Junchen(George P. & Cynthia Woods Mitchell Institute for Fundamental Physics and Astronomy, Texas A&M; University, College Station, TX, 77843, U.S.A.)

2015-01-01

We consider a certain ${\\cal N}=1$ supersymmetric, $SO(3)\\times SO(3)$ invariant, subsector of the $\\omega$-deformed family of $SO(8)$-gauged ${\\cal N}=8$ four-dimensional supergravities. The theory contains two scalar fields and two pseudoscalar fields. We look for stationary points of the scalar potential, corresponding to AdS vacua in the theory. One of these, which breaks all supersymmetries but is nonetheless stable, is new. It exists only when $\\omega\

Cracking behavior of thermally aged and irradiated CF-8 cast austenitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Chen, Y., E-mail: Yiren_Chen@anl.gov [Argonne National Laboratory, 9700 S. Cass Ave, Argonne, IL 60439 (United States); Alexandreanu, B.; Chen, W.-Y.; Natesan, K. [Argonne National Laboratory, 9700 S. Cass Ave, Argonne, IL 60439 (United States); Li, Z.; Yang, Y. [University of Florida, Gainesville, FL 32611 (United States); Rao, A.S. [US Nuclear Regulatory Commission, 11545 Rockville Pike, Rockville, MD 20852 (United States)

2015-11-15

To assess the combined effect of thermal aging and neutron irradiation on the cracking behavior of CF-8 cast austenitic stainless steel, crack growth rate (CGR) and fracture toughness J-R curve tests were carried out on compact-tension specimens in high-purity water with low dissolved oxygen. Both unaged and thermally aged specimens were irradiated at ∼320 °C to 0.08 dpa. Thermal aging at 400 °C for 10,000 h apparently had no effect on the corrosion fatigue and stress corrosion cracking behavior in the test environment. The cracking susceptibility of CF-8 was not elevated significantly by neutron irradiation at 0.08 dpa. Transgranular cleavage-like cracking was the main fracture mode during the CGR tests, and a brittle morphology of delta ferrite was often seen on the fracture surfaces at the end of CGR tests. The fracture toughness J-R curve tests showed that both thermal aging and neutron irradiation can induce significant embrittlement. The loss of fracture toughness due to neutron irradiation was more pronounced in the unaged than aged specimens. After neutron irradiation, the fracture toughness values of the unaged and aged specimens were reduced to a similar level. G-phase precipitates were observed in the aged and irradiated specimens with or without prior aging. The similar microstructural changes resulting from thermal aging and irradiation suggest a common microstructural mechanism of inducing embrittlement in CF-8.

Russkije idut, no eto skoreje G7, a ne G8 / Brian Love

Index Scriptorium Estoniae

Love, Brian

2005-01-01

Venemaa ületab takistuse maailma suurriigina tunnustamises 2006. a. jaanuaris, kui ta aastaks saab G8 eesistujaameti. Vaatamata toimunud muutustele on Venemaa endiselt külaline, kui kohtuvad G7 rahandusministrid ja keskpankade juhid

Microstructural Evolution and Mechanical Properties of Simulated Heat-Affected Zones in Cast Precipitation-Hardened Stainless Steels 17-4 and 13-8+Mo

Science.gov (United States)

Hamlin, Robert J.; DuPont, John N.

2017-01-01

Cast precipitation-hardened (PH) stainless steels 17-4 and 13-8+Mo are used in applications that require a combination of high strength and moderate corrosion resistance. Many such applications require fabrication and/or casting repair by fusion welding. The purpose of this work is to develop an understanding of microstructural evolution and resultant mechanical properties of these materials when subjected to weld thermal cycles. Samples of each material were subjected to heat-affected zone (HAZ) thermal cycles in the solution-treated and aged condition (S-A-W condition) and solution-treated condition with a postweld thermal cycle age (S-W-A condition). Dilatometry was used to establish the onset of various phase transformation temperatures. Light optical microscopy (LOM), scanning electron microscopy (SEM), and energy dispersive spectrometry (EDS) were used to characterize the microstructures, and comparisons were made to gas metal arc welds that were heat treated in the same conditions. Tensile testing was also performed. MatCalc thermodynamic and kinetic modeling software was used to predict the evolution of copper (Cu)-rich body center cubic precipitates in 17-4 and β-NiAl precipitates in 13-8+Mo. The yield strength was lower in the simulated HAZ samples of both materials prepared in the S-A-W condition when compared to their respective base metals. Samples prepared in the S-W-A condition had higher and more uniform yield strengths for both materials. Significant changes were observed in the matrix microstructure of various HAZ regions depending on the peak temperature, and these microstructural changes were interpreted with the aid of dilatometry results, LOM, SEM, and EDS. Despite these significant changes to the matrix microstructure, the changes in mechanical properties appear to be governed primarily by the precipitation behavior. The decrease in strength in the HAZ samples prepared in the S-A-W condition was attributed to the dissolution of precipitates

8-13μm spectrophotometry of galaxies

International Nuclear Information System (INIS)

Roche, P.F.; Aitken, D.K.; Whitmore, B.

1983-01-01

Spectrophotometry at 8-13 μm of Mkn 231 confirms that the 10 μm minimum is due to large columns of silicate dust in the line-of-sight to the nucleus. Fits to the detailed spectral shape demonstrate that the cool absorbing grains are at the emission (z=0.042) rather than the absorption (z approx.= 0.025) redshift and are located within the nuclear region. (author)

[2,3,7,8,13,14,17,18-Octa­kis(ethyl­sulfan­yl)-5,10,15,20-porphyrazinato]zinc(II)

Science.gov (United States)

Akkurt, Mehmet; Coşkun, Naciye Yılmaz; Kılıçaslan, Fatma Aytan; Yalçın, Sabiha Manav; Büyükgüngör, Orhan; Gül, Ahmet

2010-01-01

In the title compound, [Zn(C32H40N8S8)], the ZnII ion is coordinated by four N atoms in a slightly distorted square-planar environment. In addition, there is a Zn⋯S contact involving a symmetry-related S atom which, when considered, forms a pseudo-square-pyramidal coordination with respect to the ZnII ion. Three of the ethyl groups are disordered over two sites with occupancy ratios of 0.841 (10):0.159 (10), 0.802 (10):0.198 (10) and 0.457 (13):0.543 (13). Weak intra­molecular C—H⋯N and C—H⋯S inter­actions contribute to the stability of the mol­ecular conformation. Inter­molecular C—H⋯S contacts, weak C—H⋯π inter­actions and π–π stacking inter­actions [centroid–centriod distances = 3.832 (4) and 3.850 (5) Å] contribute to the stabilization of the crystal structure. PMID:21588217

Effect of three 2-allyl-p-mentha-6,8-dien-2-ols on inhibition of mild steel corrosion in 1 M HCl

Directory of Open Access Journals (Sweden)

S. Kharchouf

2014-11-01

Full Text Available 2-Allyl-p-mentha-6,8-dien-2-ols P1−P3 synthesized from carvone P are tested as corrosion inhibitors of steel in 1 M HCl using weight loss measurements, potentiodynamic polarisation and impedance spectroscopy (EIS methods. The addition of 2-allyl-p-mentha-6,8-dien-2-ols reduced the corrosion rate. Potentiodynamic polarisation studies clearly reveal that the presence of inhibitors does not change the mechanism of hydrogen evolution and that they act essentially as cathodic inhibitors. 2-Allyl-p-mentha-6,8-dien-2-ols tested adsorb on the steel surface according to Langmuir isotherm. From the adsorption isotherm some thermodynamic data for the adsorption process are calculated and discussed. EIS measurements show the increase of the charge-transfer resistance with the inhibitor concentration. The highest inhibition efficiency (92% is obtained for P1 at 3 g/L. The corrosion rate decreases with the rise of temperature. The corresponding activation energies are determined.

MMP-8 C-799T and MMP-8 C+17G polymorphisms in mild and severe preeclampsia: Association between MMP-8 C-799T with susceptibility to severe preeclampsia.

Science.gov (United States)

Rahimi, Ziba; Zangeneh, Maryam; Rezaeyan, Arezoo; Shakiba, Ebrahim; Rahimi, Zohreh

2018-01-01

The aim of present study was to determine the role of matrix metalloproteinase-8 (MMP-8) C-799T (rs11225395) and C+17 (rs2155052) polymorphisms in susceptibility to preeclampsia. In a case-control study, 256 pregnant women including 152 women with preeclampsia (86 women with mild preeclampsia and 66 women with severe preeclampsia) and 104 women with normal pregnancy from Western Iran with Kurdish ethnic background were investigated for MMP-8 C-799T and C + 17G polymorphisms using polymerase chain reaction-restriction fragment length polymorphism method. Comparing the MMP-8 TT genotype with the combined genotype of CC+CT (recessive model) indicated a significantly higher frequency of the MMP-8 TT genotype (47%) in severe preeclamptic patients than that in healthy pregnant women (30.8%) that was associated with 1.99-fold increased risk of severe preeclampsia (95% CI = 1.05-3.77, p = 0.034). The frequency of MMP-8 G allele was 27.3% in all preeclamptic patients compared to 30.2% in controls (p = 0.56). Also, no significant difference was detected comparing the frequency of G allele in mild (26.6%, p = 0.46) and severe preeclamptic patients (28.4%, p = 0.75) with controls (30.2%). Our study demonstrated that the MMP-8 C-799T is associated with the risk of developing severe preeclampsia during pregnancy. However, the MMP-8 C + 17G polymorphism might not be a risk factor for susceptibility to preeclampsia.

H-2g, a glucose analog of blood group H antigen, mediates monocyte recruitment in vitro and in vivo via IL-8/CXCL8

Directory of Open Access Journals (Sweden)

Rabquer BJ

2012-09-01

Full Text Available Bradley J Rabquer,1,2 Yong Hou,1 Jeffrey H Ruth,1 Wei Luo,1 Daniel T Eitzman,1 Alisa E Koch,3,1 Mohammad A Amin11University of Michigan Medical School, Department of Internal Medicine, Ann Arbor, MI, USA; 2Albion College, Biology Department, Albion, MI, USA; 3VA Medical Service, Department of Veterans Affairs, Ann Arbor, MI, USAObjective: Monocyte (MN recruitment is an essential inflammatory component of many autoimmune diseases, including rheumatoid arthritis (RA. In this study we investigated the ability of 2-fucosyllactose (H-2g, a glucose analog of blood group H antigen to induce MN migration in vivo and determined if H-2g-induced interleukin-8 (IL-8/CXCL8 plays a role in MN ingress in RA.Methods: Sponge granuloma and intravital microscopy assays were performed to examine H-2g-induced in vivo MN migration and rolling, respectively. MNs were stimulated with H-2g, and the production of IL-8/CXCL8 was assessed by enzyme-linked immunosorbent assay and quantitative polymerase chain reaction. Lastly, in vitro MN migration assays and an in vivo RA synovial tissue severe combined immunodeficiency mouse model were used to determine the role of IL-8/CXCL8 in H-2g-induced MN migration.Results: In vivo, H-2g induced significantly greater MN migration compared to phosphate buffered saline. Intravital microscopy revealed that H-2g mediates MN migration in vivo by inducing MN rolling. In addition, H-2g induced MN production of IL-8/CXCL8, a process that was dependent on Src kinase. Moreover, we found that H-2g mediated MN migration in vitro, and in vivo migration was inhibited by a neutralizing anti-IL-8/CXCL8 antibody.Conclusion: These findings suggest that H-2g mediates MN recruitment in vitro and in vivo (in part via IL-8/CXCL8.Keywords: inflammation, rheumatoid arthritis, chemokine, migration

Future prospects of the international G-8 Global Partnership Programme

International Nuclear Information System (INIS)

Grigor'ev, A.V.; Esaulova, A.V.

2012-01-01

The Global Partnership Programme Against the Spread of Weapons and Materials of Mass Destruction was adopt at the Group-8 (G-8) summit on the 27-th of June 2002 for 10 years. At the G-8 summit in May 2011, the decision was made to extent the Global Partnership Programme to beyond 2012 and to expand its reach and geographical coverage. New areas for cooperation were named, such as: nuclear, radiological and biological safety, employment of scientists involved with sensitive industries and assistance to third countries in their compliance with the provisions of United Nations Security Council Resolution No 1540. The parties re-affirmed their commitment to completing a series of priority projects in Russia [ru

Radiation embrittlement of WWER 440 pressure vessel steel and of some improved steels by western producers

International Nuclear Information System (INIS)

Koutsky, J.; Vacek, M.; Stoces, B.; Pav, T.; Otruba, J.; Novosad, P.; Brumovsky, M.

1982-01-01

The resistance was studied of Cr-Mo-V type steel 15Kh2MFA to radiation embrittlement at an irradiation temperature of around 288 degC. Studied was the steel used for the manufacture of the pressure vessel of the Paks nuclear reactor in Hungary. The obtained results of radiation embrittlement and hardening of steel 15Kh2MFA were compared with similar values of Mn-Ni-Mo type steels A 533-B and A 508 manufactured by leading western manufacturers within the international research programme coordinated by the IAEA. It was found that the resistance of steel 15Kh2MFA to radiation embrittlement is comparable with steels A 533-B and A 508 by western manufacturers. (author)

Effect of smelting method on the austenite grain size and properties of heat-resisting pearlitic steel

International Nuclear Information System (INIS)

Balakhovskaya, M.B.; Khusainova, N.A.; Davlyatova, L.N.

1975-01-01

Influence of smelting method on austenite grain size and properties of refractory perlite steel were studied. An opportunity was found to increase the steel refractoriness without deteriorating its other properties. The steel 12Kh1MF of electric or common open-hearth smelting was used. The dependence of kinetics of austenite grain growth on the smelting method was studied in the temperature range 950 deg - 1200 deg C with 1 hour exposure. The grain size of austenite in steel is supposedly determined by aluminium nitrides and vanadium carbides. In tests of normalized (kept for 20 minutes at 950-980 deg C) and tempered (kept for 3 hours at 730 deg C) transverse (tangential) pipe cross-section samples the electric steel had higher impact viscosity than the open-hearth metal. At working temperatures (540 deg -580 deg C) the difference in viscosity has its minimum. Viscosity of both steels 12Kh1MF begins to sharply decrease from 20 deg C. However, electric steel has rather high viscosity even at - 40 deg C, while the open-hearth one becomes brittle as early as at - 20 deg C. Long-term strength tests at 580 deg C under stresses 10-14 kG/mm 2 show that the coarse-grain steel is more refractory, i.e. time till fracture of open-hearth steel samples is twice as long as that of electric steel samples

On-shell diagrams for N=8 supergravity amplitudes

Energy Technology Data Exchange (ETDEWEB)

Heslop, Paul; Lipstein, Arthur E. [Department of Mathematical Sciences, Durham University,Lower Mountjoy, Stockton Road, Durham, DH1 3LE (United Kingdom)

2016-06-10

We define recursion relations for N=8 supergravity amplitudes using a generalization of the on-shell diagrams developed for planar N=4 super-Yang-Mills. Although the recursion relations generically give rise to non-planar on-shell diagrams, we show that at tree-level the recursion can be chosen to yield only planar diagrams, the same diagrams occurring in the planar N=4 theory. This implies non-trivial identities for non-planar diagrams as well as interesting relations between the N=4 and N=8 theories. We show that the on-shell diagrams of N=8 supergravity obey equivalence relations analogous to those of N=4 super-Yang-Mills, and we develop a systematic algorithm for reading off Grassmannian integral formulae directly from the on-shell diagrams. We also show that the 1-loop 4-point amplitude of N=8 supergravity can be obtained from on-shell diagrams.

Functionalization of SU-8 Photoresist Surfaces with IgG Proteins

DEFF Research Database (Denmark)

Blagoi, Gabriela; Keller, Stephan Urs; Johansson, Alicia

2008-01-01

immunoassays were employed to characterize the binding efficiency of model proteins to bare SU-8 surface, SU-8 treated with cerium ammonium nitrate (CAN) etchant and CAN treated surfaces modified by aminosilanization. The highest binding capacity of antibodies was observed on bare SU-8. This explains why bare...... SU-8 in a functional fluorescent sandwich immunoassay detecting C-reactive protein (CRP) gave twice as high signal as compared with the other two surfaces. Immunoassays performed on bare SU-8 and CAN treated SU-8 resulted in detection limits of CRP of 30 and 80 ng/ml respectively which is sufficient...... for detecting CRP in clinical samples, where concentrations of 3–10 μg/ml are normal for healthy individuals. In conclusion, bare SU-8 and etched SU-8 can be modified with antibodies by a simple adsorption procedure which simplifies building lab-on-a-chip systems in SU-8. Additionally, we report the fabrication...

Inter-laboratory validation of procedures for measuring 8-oxo-7,8-dihydrooxoguanine/8-oxo-7,8-dihydro-2`-deoxyguanosine in DNA

DEFF Research Database (Denmark)

Collins, A.R.; Gedik, C.M.; Wood, S.

2002-01-01

The aim of ESCODD, a European Commission funded Concerted Action, is to improve the precision and accuracy of methods for measuring 8-oxo-7,8-dihydroguanine (8-oxoGua) or the nucleoside (8-oxodG). On two occasions, participating laboratories received samples of different concentrations of 8-oxodG...

High Temperature Creep of an Al-8,5Fe-1,3V-1,7Si Alloy

Czech Academy of Sciences Publication Activity Database

Kuchařová, Květa; Zhu, S. J.; Čadek, Josef

2002-01-01

Roč. 40, č. 2 (2002), s. 69-84 ISSN 0023-432X R&D Projects: GA AV ČR IBS2041001 Institutional research plan: CEZ:AV0Z2041904 Keywords : Al-8,5Fe 1,3V 1,7Si alloy * creep behavior , true threshold stress Subject RIV: JI - Composite Materials Impact factor: 0.493, year: 2002

Mechanochemical synthesis and crystal structure of a 1:2 co-crystal of 1,3,6,8-tetraazatricyclo[4.3.1.13,8]undecane (TATU and 4-chloro-3,5-dimethylphenol

Directory of Open Access Journals (Sweden)

Augusto Rivera

2016-11-01

Full Text Available Solvent-free treatment of 1,3,6,8-tetraazatricyclo[4.3.1.13,8]undecano (TATU with 4-chloro-3,5-dimethylphenol led to the formation of the title co-crystal, C7H14N4·2C8H9ClO. The asymmetric unit contains one aminal cage molecule and two phenol molecules linked via two O—H...N hydrogen bonds. In the aminal cage, the N–CH2–CH2–N unit is slightly distorted from a syn periplanar geometry. Aromatic π–π stacking between the benzene rings from two different neighbouring phenol molecules [centroid–centroid distance = 4.0570 (11 Å] consolidates the crystal packing.

[IgG4-related lung disease: analysis of 8 cases and literature review].

Science.gov (United States)

Han, G J; Hu, H; Mao, D; Bai, X; She, D Y; Zhao, S F; Wen, Z L; Gao, J

2017-03-12

Objective: To improve the understanding and treatment of IgG4-related lung disease (IgG4-RLD). Methods: The clinical characteristics, serum IgG4 levels, pathological features, chest CT, therapy and prognosis of 8 patients with IgG4-RLD were retrospectively analyzed. These patients were admitted to the People's Liberation Army General Hospital and the pathological diagnosis was made between December 2005 and March 2016. Relevant literatures were reviewed. Results: The 8 patients with IgG4-RLD included 4 men and 4 women, with an average age of (59±4) years (range, 37-74). The respiratory symptoms included shortness of breath, cough, and expectoration. Extra-pulmonary symptoms included abdominal pain, facial edema, and fever. Extrapulmonary organs were involved in 7 cases. Serum IgG4 levels were elevated in 8 cases, with an average concentration of(17±6)g/L. Chest CT showed solid lung nodules in 6, alveolar-interstitial infiltration in 5, bronchovascular lesions in 3 and ground glass shadows in 2 cases. PET/CT was performed in 2 cases and it showed multiple organ involvement with higher radioactivity uptake(SUVmax2.9-4.2). The pathological examination found lymphocyte and plasma cell infiltration in 7, fibrous tissue hyperplasia in 5, and occlusive vasculitis in 2 cases. On immunohistochemical staining, the ratio of IgG4-positive plasma cells to IgG-positive plasma cells was higher than 40%in 3 cases. The number of IgG4-positive plasma cells was 10-50/HP in 8 cases. The misdiagnosis rate was 100% before the final diagnosis was made. Three cases received glucocorticoids with immunosuppressant therapy, 2 received surgery combined with glucocorticoid therapy, 2 received glucocorticoid therapy alone, and 1 only received surgery. The follow-up time was 4-132 months, with remission in 7 cases, and disease progression in 1 case, but no death. A total of 195 cases of IgG4-RLD were reviewed from the literature, among whom 111 cases were admitted with respiratory symptoms

Corrosion of chromium, nickel, titanium and steels in solutions of sodium and ammonium thiosulfates

International Nuclear Information System (INIS)

Grebenshchikova, S.V.; Kochergin, V.P.; Doronina, I.V.

1983-01-01

Results of gravimetric determinatiion of average rate of chromium, nickel, titatnium and steels 12Kh18N10T and VSt.3 corrosion rate in solutions 50 mass.% (NH 4 ) 2 S 2 O 3 and Na 2 S 2 O 3 in the air and nitrogen atmosphere at 333 K have been generalized. Anodic polarization curves are recorded and stationary potentials of metals and steels under the conditions are measured. It is shown that in (NH 4 ) 2 S 2 O 3 solution the rate of metal and steels corrosion is higher than in Na 2 S 2 O 3 solution indepenent of the nature of gaseous medium contacting with solution. In the series Ni → VSt.3 → 12Kh18N10T → VT1 → chromium in (NH 4 ) 2 S 2 O 3 and Na 2 S 2 O 3 solutions at 333 K corrosion resistance increases. Chromium, titanium and chromium-nickel steel 12Kh18N10T possess a high corrosion resistance

El discurso hegemónico sobre las acciones colectivas de resistencia civil: Casos comunas 8, 9 y 13 de Medellín The Hegemonic Discourse about Collective Actions of Civil Resistance: Cases Communes 8, 9 and 13 of Medellín

Directory of Open Access Journals (Sweden)

Mary Luz Alzate Zuluaga

2010-01-01

Full Text Available En este artículo se discute la manera cómo en la prensa escrita son informadas las distintas expresiones de resistencia civil, a partir del rastreo de la información registrada en la prensa escrita local y nacional acerca de los casos de las Comunas 8, 9 y 13 de la ciudad de Medellín durante los años 2002-2006. Se busca conocer así, de qué modo han sido descritas e interpretadas dichas prácticas, cuáles son las ausencias y los aspectos subrayados con lo emitido, qué relaciones de poder se legitiman, entre otras cuestiones. Llegando a afirmar la existencia de un discurso difundido y legitimado en los medios masivos de comunicación, acorde con el orden social y político hegemónico y dominante en Colombia. Este discurso consiste en la invisibilidad de los mensajes políticos de denuncia y oposición frente a los actores armados y sus dinámicas de guerra, y también consiste en la minimización del desafío de las prácticas colectivas producidas cotidianamente en defensa de los derechos vulnerados de los habitantes de los barrios populares y en busca del reconocimiento y justicia frente a la exclusión social y política.This article discusses the way that Press reports about the different expressions of civil resistance from tracking information registered on the local and national press about the cases of Communes 8, 9 and 13 of the city of Medellín during the years 2002-2006. The intention is to know how such practices have been described and interpreted, which are the absences and emphasized aspects with the emitted information, what power relations are legitimized, among other questions. There is an affirmation of the existence of a legitimate and spread discourse on the media consistent with the social and political hegemonic order in Colombia. This discourse consist in the invisibility of the political message of denunciation and opposition to the armed actors and their war dynamics, and also consists in the minimization of

Unraveling the Structure-Affinity Relationship between Cucurbit[n]urils (n=7, 8) and Cationic Diamondoids

Czech Academy of Sciences Publication Activity Database

Sigwalt, D.; Šekutor, M.; Cao, L.; Zavalij, P. Y.; Hostaš, Jiří; Ajani, Haresh; Hobza, Pavel; Mlinaric-Majerski, K.; Glaser, R.; Isaacs, L.

2017-01-01

Roč. 139, č. 8 (2017), s. 3249-3258 ISSN 0002-7863 R&D Projects: GA ČR(CZ) GBP208/12/G016 Institutional support: RVO:61388963 Keywords : host-guest complexation * high- energy water * driving force Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 13.858, year: 2016

Tool life equation for blanking 18-8 stainless steel strips

Directory of Open Access Journals (Sweden)

Faura, F.

1998-08-01

Full Text Available Hereinafter it is presented a model for the behaviour and life of circular blanking tool used in sheet forming processes of 18-8 stainless steel (sheet thickness: 1 mm. Firstly it has analyzed the different studies that have previously delt with this problem. Secondly taking into account recently made experiments, it is proposed a simple formulation to predict tool life with enough reliability. To this purpose it has examined different parameters in the wear process, inferring from these the fundamental parameters that regulate them and about which the different equations have been configurated. Blanking tests were performed using a 20 t press at a speed of 150 strokes/min. Punch materials used in these tests were AISI A2 and AISI D2 with diameters between 1.5 and 10 mm. The blanking tests were performed at a clearance between 5 and 20 % of the work material thickness.

En el presente artículo se presenta un modelo de ecuación de vida de herramientas para punzonado circular de chapa de acero inoxidable 18-8 (1 mm de espesor. Se han analizado inicialmente los diferentes estudios que previamente han abordado este problema. Posteriormente, teniendo en cuenta los experimentos realizados recientemente, se propone una formulación simple para predecir con Habilidad suficiente la vida de la herramienta. Para este propósito se han examinado los diferentes parámetros que afectan al proceso de desgaste, infiriendo a partir de estos, los parámetros fundamentales que lo regulan y sobre los cuales se han configurado las diferentes ecuaciones. Los ensayos fueron realizados en una prensa de 20 t y una velocidad de punzonado de 150 golpes/min. Los materiales de los punzones usados en los ensayos fueron AISI A2 y AISI D2 con diámetros comprendidos entre 1,5 y 10 mm. Los ensayos se realizaron para juegos de corte comprendidos entre un 5 y 20 % del espesor de la chapa.

Effect of metal properties of casts of steel-15Kh1M1FL on the crack resistance at 565 deg C

International Nuclear Information System (INIS)

Gladshtejn, V.I.; Sheshenev, M.F.

1976-01-01

Results are given of prolonged tests of the metal of industrial casts with various fluidity limits. It has been shown experimentally that a quite satisfactory crack resistance is characteristic of a metal with a fluidity limit in the range 30-50 kgf/mm 2 . Metallographic studies have been conducted. Upon variation of the structure and properties of the 15Kh1M1FL steel during operation, the rate of growth of small cracks (up to 2.0 mm) decreases almost by 3 orders of ten (from 1.4x10 -4 to 2.0x10 -7 mm/hour). Subsequent structural changes during prolonged operation (over 50000 hours) result in a gradual increase in the rate of crack growth. At the same time resistance towards appearance of the impermissible high rate of the crack growth, Ksub(10sup(-3)), diminishes monotonically with the operation time. The metal of industrial 15Kh1M1FL steel casts has good crack resistance (Ksub(10sup(-3)) =30-70 kgf/mmsup(3/2) and Vsub(ef) =) kgf/mm 2 ) and a satisfactory local plasticity (critical opening being no more than 0.20 mm for 10 3 hours)

Measurements of the 40Ar(n, γ)41Ar radiative-capture cross section between 0.4 and 14.8 MeV

Science.gov (United States)

Bhike, Megha; Fallin, B.; Tornow, W.

2014-09-01

The 40Ar(n, γ)41Ar neutron capture cross section has been measured between 0.4 and 14.8 MeV neutron energy using the activation technique. The data are important for estimating backgrounds in argon-based neutrino and dark-matter detectors and in the neutrino-less double-beta decay search GERDA, which uses liquid argon as cooling and shielding medium. For the first time the 40Ar(n, γ)41Ar cross section has been measured for neutron energies above 1 MeV. Our results are compared to the evaluation ENDF/B-VII.1 and the calculated prediction TENDL-2013. The latter agrees very well with the present results.

Enhancement of strength properties of hot rolled 10KHSND steel

International Nuclear Information System (INIS)

Nasibov, A.G.; Popova, L.V.; Pikulin, S.A.; Globa, N.I.

1989-01-01

To find out the reasons of low hot rolling yield for 10KhSND steel sheets in mechanical properties, titanium effect in the range of 0.008-0.03% concentrations is studied. It is established that the titanium content in a solid solution is conserved within 0.003-0.005%, the rest of titanium is bound to carbonitrides Ti(C, N). It is shown that alloys with 0.025-0.03% titanium content possess the increased values of ultimate and yield strength the necessary level of impact strength and good wealdability. The good steel yield, when the titanium content is sustained at the given level, increases from 40 to 85%

Study of the interactions of 13.8 GeV/c protons with the heavy nuclei of the emulsions exposed in magnetic fuel of 170 kgauss; Estudio de las interacciones de protones de 13,8 geV/c con los nucleos pesados de emusiones

Energy Technology Data Exchange (ETDEWEB)

Gomez Aleixandre, J L

1967-07-01

145 stars with N{sub h}>8 produced by the interactions of 13.8 GeV/c protons with Ag and Br nuclei have been analysed. The emulsion stack was irradiated in a 170 K gauss magnetic field. Statistical results concerning the main characteristics of the different particles emitted are given and the energy balance is evaluated. The main features of both 24 GeV/c protons and 17 GeV/c {pi}- interactions are compared with those we have found for 13.8 GeV/c protons interactions. (Author) 27 refs.

JP-8 Final Risk Assessment

Science.gov (United States)

2001-08-01

History of diabetes 8. History of scoliosis 9. Major visual impairment 10. Clinical diagnosis of seizures 11. On medical profile 12. Pregnancy 13...genotype is over-represented in patients with certain types of cancer. It has also been reported that the GST MI-null genotype is more prevalent among...induced haemolytic anaemia with haemoglobinuria. Indian J.Pediatr. 40, 195-197, 1973. 8. Hauf L.M. The development of a method Suitable for the

Determination of constant of chemical reaction rate in the process of steel treatment in the endothermal atmosphere

International Nuclear Information System (INIS)

Gyulikhandanov, E.L.; Kislenkov, V.V.

1978-01-01

The high-temperature method was applied to measuring a relative variation in the electrical resistance of a thin steel foil prepared from the 12KhN3A, 18Kh2N4VA, 20KhGNR, and 20Kh3MVF steels during its carburization and decarburization, and determined was the temperature dependence of the reaction rate of the interaction of the endothermal atmosphere of different compositions with the analloyed γ-Fe. A connection has been established between the reaction rate constant and the thermodynamic activity of carbon in the alloyed austenite at the temperature of about 925 deg C, corresponding to the cementation temperature. This provides the quantitative estimation of the above value for any alloyed steels and with the presence of numerical values of diffusion coefficients; this also enables one to carry out an accurate calculation of the distribution of carbon throughout the depth of a layer when effecting the cementation in the endothermal atmosphere

The effect of smoking on the urinary excretion of 8-oxodG and 8-oxoGuo in patients with type 2 diabetes

DEFF Research Database (Denmark)

Sørensen, Anne-Sofie; Kjær, Laura Kofoed; Petersen, Kasper Meidahl

2017-01-01

as urinary 8-oxo-7, 8-dihydro-2'-deoxyguanosine (8-oxodG) excretion in smokers compared with non-smokers in a healthy population. We aimed to investigate if an increased urinary excretion of 8-oxodG in smokers versus never smokers and former smokers could be verified in a population with type 2 diabetes......Over the past decades, attention has been paid to understanding the impact of oxidative stress and related modifications of DNA and RNA on various human health risks. A recent meta-analysis comprising 1915 smokers and 3462 non-smokers found a significantly higher level of DNA oxidation measured...... to examine the relationship between daily smokers (n = 462) versus former (n = 1341) and never smokers (n = 918) regarding the RNA and DNA oxidation, respectively. We did not find any significant effect of smoking on urinary excretion of 8-oxodG or 8-oxoGuo in our study. Due to a sparse study area...

Hierarchically Porous N-doped Carbon Derived from ZIF-8 Nanocomposites for Electrochemical Applications

International Nuclear Information System (INIS)

Jiang, Min; Cao, Xueping; Zhu, Dandan; Duan, Yongxin; Zhang, Jianming

2016-01-01

A core-shell structure composite, zeolitic imidazolate framework @ cetyltrimethylammonium bromide (ZIF-8@CTAB) was synthesized by CTAB micelle controlling the growth of ZIF-8 in aqueous systems. Direct carbonization of ZIF-8@CTAB at a high temperature produced the nitrogen-doped hierarchically porous carbon (named as PC1000@C). In comparison with the carbonization product of pure ZIF-8 (named as PC1000), PC1000@C possesses the higher specific surface area and two-times larger total pore volume. The results from elemental analysis shows the higher N content in PC1000 sample, while X-ray photoelectron spectroscopy curve-fitting shows the higher quaternary-N content in PC1000@C sample. The hierarchical microporous/mesoporous structure, high surface area and favorable N species in PC1000@C play an active role in catalyzing oxygen reduction reaction (ORR). The specific capacitance of porous carbon was calculated from the galvanostatic-discharge curve. PC1000@C exhibits a large specific capacitance of 225 F g"−"1 at a current density of 0.5 A g"−"1 and still retains 92% of initial capacitance after 1000 galvanostatic charge-discharge cycles.

Study of the decarburization of 18-8 stainless steel by oxygen at low pressure

International Nuclear Information System (INIS)

Armand, G.; Lapujoulade, J.

1964-01-01

The kinetic of the decarburization of a 18-8 stainless-steel by oxygen at low pressure has been studied between 1050 and 1200 C. The measurement of the carbon content of the sample is carried out by chemical analysis. Three mechanisms take place in that decarburization: diffusion of carbon in the steel; velocity at the superficial reaction C + 1/2 O 2 ↔ CO; pumping out of CO. The second mechanism seems to govern the overall kinetic. The activation energy of the phenomenon is 108 ± 24 Kcal/mole. (authors) [fr

8q24 rs6983267G variant is associated with increased thyroid cancer risk

Science.gov (United States)

Sahasrabudhe, Ruta; Estrada, Ana; Lott, Paul; Martin, Lynn; Echeverry, Guadalupe Polanco; Velez, Alejandro; Neta, Gila; Takahasi, Meiko; Saenko, Vladimir; Mitsutake, Norisato; Jaeguer, Emma; Duque, Carlos Simon; Rios, Alejandro; Bohorquez, Mabel; Prieto, Rodrigo; Criollo, Angel; Echeverry, Magdalena; Tomlinson, Ian; Carvajal Carmona, Luis G.

2015-01-01

The G allele of the rs6983267 single nucleotide polymorphism, located on chromosome 8q24, has been associated with increased risk of several cancer types. The association between rs6983267G and thyroid cancer has been tested in different populations, mostly of European ancestry, and has led to inconclusive results. While significant associations have been reported in the British and Polish populations, no association has been detected in populations from Spain, Italy and the USA. To further investigate the role of rs6983267G in thyroid cancer susceptibility, we evaluated rs6983267 genotypes in three populations of different continental ancestry (British Isles, Colombia and Japan), providing a total of 3,067 cases and 8,575 controls. We detected significant associations between rs6983267G and thyroid cancer in the British Isles (Odds Ratio, OR= 1.19, 95% confidence interval, CI: 1.11–1.27, P= 4.03 × 10−7), Japan (OR= 1.20, 95% CI: 1.03–1.41, P= 0.022) and a borderline significant association of similar effect direction and size in Colombia (OR= 1.19, 95% CI: 0.99–1.44, P= 0.069). A meta-analysis of our multi-ethnic study and previously published non-overlapping datasets, which included a total of 5,484 cases and 12,594 controls, confirmed the association between rs6983267G and thyroid cancer (P= 1.23 × 10−7, OR= 1.13, 95% CI: 1.07–1.18). Our results therefore support the notion that rs6983267G is a bona fide thyroid cancer risk variant that increases the risk of disease by ~13%. PMID:26290501

Effect of helium ion bombardment on hydrogen behaviour in stainless steel

International Nuclear Information System (INIS)

Guseva, M.I.; Stolyarova, V.G.; Gorbatov, E.A.

1987-01-01

The effect of helium ion bombardment on hydrogen behaviour in 12Kh18N10T stainless steel is investigated. Helium and hydrogen ion bombardment was conducted in the ILU-3 ion accelerator; the fluence and energy made up 10 16 -5x10 17 cm -2 , 30 keV and 10 16 -5x10 18 cm -2 , 10 keV respectively. The method of recoil nuclei was used for determination of helium and hydrogen content. Successive implantation of helium and hydrogen ions into 12Kh18N10T stainless steel results in hydrogen capture by defects formed by helium ions

Choice of corrosion-resistant metal for fluotitanic acid

International Nuclear Information System (INIS)

Reingeverts, M.D.; Lapchenko, E.P.; Semenyuk, E.Y.

1986-01-01

The authors investigate the corrosion and anodic behavior of steels 12Kh18N10T, 08Kh21N6M2T, and 06KhN28MDT, nickel, and molybdenum in 10-40% naturally aerated solutions of H 2 TiF 6 at 20 and 50 degrees C. The authors found that in solutions of fluotitanic acid, as also in tetrafluoroboric and hydrofluoric acids, the most stable alloys are chromium-nickel-molybdenum alloy of type 06KhN28MDT and (for acid concentrations above 20%) copper-nickel-alloys of the monel metal type. Steels 12Kh18N10T and 08Kh21N6M2T can be used in acid concentrations of less than 10% and temperatures up to 20 degrees C with anodic protection

OSBP-related protein 8 (ORP8) interacts with Homo sapiens sperm associated antigen 5 (SPAG5) and mediates oxysterol interference of HepG2 cell cycle

International Nuclear Information System (INIS)

Zhong, Wenbin; Zhou, You; Li, Jiwei; Mysore, Raghavendra; Luo, Wei; Li, Shiqian; Chang, Mau-Sun; Olkkonen, Vesa M.; Yan, Daoguang

2014-01-01

We earlier identified OSBP-related protein 8 (ORP8) as an endoplasmic reticulum/nuclear envelope oxysterol-binding protein implicated in cellular lipid homeostasis, migration, and organization of the microtubule cytoskeleton. Here, a yeast two-hybrid screen identified Homo sapiens sperm associated antigen 5 (SPAG5)/Astrin as interaction partner of ORP8. The putative interaction was further confirmed by pull-down and co-immunoprecipitation assays. ORP8 did not colocalize with kinetochore-associated SPAG5 in mitotic HepG2 or HuH7 cells, but overexpressed ORP8 was capable of recruiting SPAG5 onto endoplasmic reticulum membranes in interphase cells. In our experiments, 25-hydroxycholesterol (25OHC) retarded the HepG2 cell cycle, causing accumulation in G2/M phase; ORP8 overexpression resulted in the same phenotype. Importantly, ORP8 knock-down dramatically inhibited the oxysterol effect on HepG2 cell cycle, suggesting a mediating role of ORP8. Furthermore, knock-down of SPAG5 significantly reduced the effects of both ORP8 overexpression and 25OHC on the cell cycle, placing SPAG5 downstream of the two cell-cycle interfering factors. Taken together, the present results suggest that ORP8 may via SPAG5 mediate oxysterol interference of the HepG2 cell cycle. - Highlights: • The oxysterol-binding protein ORP8 was found to interact with the mitotic regulator SPAG5/Astrin. • Treatment of HepG2 cells with 25-hydroxycholesterol caused cell cycle retardation in G2/M. • ORP8 overexpression caused a similar G2/M accumulation, and ORP8 knock-down reversed the 25-hydroxycholesterol effect. • Reduction of cellular of SPAG5/Astrin reversed the cell cycle effects of both 25-hydroxycholesterol and ORP8 overexpression. • Our results suggest that ORP8 mediates via SPAG5/Astrin the oxysterol interference of HepG2 cell cycle

OSBP-related protein 8 (ORP8) interacts with Homo sapiens sperm associated antigen 5 (SPAG5) and mediates oxysterol interference of HepG2 cell cycle

Energy Technology Data Exchange (ETDEWEB)

Zhong, Wenbin [Department of Biotechnology, Jinan University, Guangzhou 510632 (China); Zhou, You [Minerva Foundation Institute for Medical Research, Helsinki (Finland); Li, Jiwei [Department of Biotechnology, Jinan University, Guangzhou 510632 (China); Mysore, Raghavendra [Minerva Foundation Institute for Medical Research, Helsinki (Finland); Luo, Wei; Li, Shiqian [Department of Biotechnology, Jinan University, Guangzhou 510632 (China); Chang, Mau-Sun [Institute of Biochemical Sciences, National Taiwan University, No. 1, Taipei, Taiwan (China); Olkkonen, Vesa M. [Minerva Foundation Institute for Medical Research, Helsinki (Finland); Yan, Daoguang, E-mail: tydg@jnu.edu.cn [Department of Biotechnology, Jinan University, Guangzhou 510632 (China)

2014-04-01

We earlier identified OSBP-related protein 8 (ORP8) as an endoplasmic reticulum/nuclear envelope oxysterol-binding protein implicated in cellular lipid homeostasis, migration, and organization of the microtubule cytoskeleton. Here, a yeast two-hybrid screen identified Homo sapiens sperm associated antigen 5 (SPAG5)/Astrin as interaction partner of ORP8. The putative interaction was further confirmed by pull-down and co-immunoprecipitation assays. ORP8 did not colocalize with kinetochore-associated SPAG5 in mitotic HepG2 or HuH7 cells, but overexpressed ORP8 was capable of recruiting SPAG5 onto endoplasmic reticulum membranes in interphase cells. In our experiments, 25-hydroxycholesterol (25OHC) retarded the HepG2 cell cycle, causing accumulation in G2/M phase; ORP8 overexpression resulted in the same phenotype. Importantly, ORP8 knock-down dramatically inhibited the oxysterol effect on HepG2 cell cycle, suggesting a mediating role of ORP8. Furthermore, knock-down of SPAG5 significantly reduced the effects of both ORP8 overexpression and 25OHC on the cell cycle, placing SPAG5 downstream of the two cell-cycle interfering factors. Taken together, the present results suggest that ORP8 may via SPAG5 mediate oxysterol interference of the HepG2 cell cycle. - Highlights: • The oxysterol-binding protein ORP8 was found to interact with the mitotic regulator SPAG5/Astrin. • Treatment of HepG2 cells with 25-hydroxycholesterol caused cell cycle retardation in G2/M. • ORP8 overexpression caused a similar G2/M accumulation, and ORP8 knock-down reversed the 25-hydroxycholesterol effect. • Reduction of cellular of SPAG5/Astrin reversed the cell cycle effects of both 25-hydroxycholesterol and ORP8 overexpression. • Our results suggest that ORP8 mediates via SPAG5/Astrin the oxysterol interference of HepG2 cell cycle.

Standard Molar Enthalpy of Formation of RE(C5H8NS2)3(C12H8N2)

Institute of Scientific and Technical Information of China (English)

Meng Xiangxin; Shuai Qi; Chen Sanping; Xie Gang; Gao Shengli; Shi Qizhen

2005-01-01

Four solid ternary complexes of RE (C5H8NS2)3(C12H8N2) (RE=Eu, Gd, Tb, Dy) were synthesized in absolute ethanol by rare earth chloride low hydrate with the mixed ligands of ammonium pyrrolidinedi-thiocarbamate (APDC) and 1, 10-phenanthroline*H2O (o-phen*H2O) in the ordinary laboratory atmosphere without any cautions against moisture or air sensitivity. IR spectra of the complexes show that the RE3+ coordinated with six sulfur atoms of three PDC- and two nitrogen atoms of o-phen*H2O. It was assumed that the coordination number of RE3+ is eight. The constant-volume combustion energies of the complexes, ΔcU, were determined as (-16937.88±9.79 ), (-17588.79±8.62 ), (-17747.14±8.25 ) and (-17840.37±8.87 ) kJ*mol-1, by a precise rotating-bomb calorimeter at 298.15 K. Its standard molar enthalpies of combustion, ΔcHθm, and standard molar enthalpies of formation, ΔfHθm, were calculated as (-16953.37±9.79), (-17604.28±8.62), (-17762.63±8.25), (-17855.86±8.87) kJ*mol-1 and (-857.04±10.52), (-282.43±9.58), (-130.08±9.13), (-55.75±9.83) kJ*mol-1.

Structure and stability of M6N8 clusters (M = Si, Ge, Sn, Ti).

Science.gov (United States)

Davydova, Elena I; Timoshkin, Alexey Y; Frenking, Gernot

2010-06-10

The structures and stabilities of the M(6)N(8) clusters (M = Si, Ge, Sn, Ti) have been theoretically studied at DFT and ab initio levels of theory. Two new isomers have been considered: cage-like molecules and propeller-like molecules. It is shown that only for M = Si are both isomers true minima on the potential energy surface. The thermodynamics of the dissociation process (1/6)M(6)N(8) --> (1/3)M(3)N(4) is discussed. For each M(3)N(4) molecule, four structures with different multiplicity are considered. The thermodynamic analysis shows that independently of the multiplicity of M(3)N(4) nitrides all M(6)N(8) clusters are stable in the gas phase in a wide temperature range and could be potential intermediates in chemical vapor deposition of the nitride materials.

Synthesis and X-Ray Crystal Structures of Mononuclear Complexes of 1,3-Bis(8-quinolyloxy)propane

International Nuclear Information System (INIS)

Al-Mandhary, M.R.; Steel, P.

2002-01-01

The preparations and X-ray crystal structures of the first transition metal complexes of 1,3-bis(8-quinolyloxy)propane are described. The ligand acts as a trans-chelating N,N'-bidentate ligand in the three-coordinate silver nitrate complex and four-coordinate copper chloride complex, but as an N,O,O',N'-tetradentate ligand in the octahedral nickel chloride complex. Copyright (2002) CSIRO Australia

Structural steels for power generating equipment and heat and chemical heat treatments

International Nuclear Information System (INIS)

Astaf'ev, A.A.

1979-01-01

Development of structural steels for power generating equipment and for reactor engineering, in particular, is elucidated. Noted is utilization of the 15Kh2NMFA steels for the WWER-1000 reactor vessels, the 10GN2MFA steels for steam generators, pressurizers, vessels of the automatic emergency shut down and safety system; the 00Kh12N3DL steel for cast pump vessels and main locking bars. The recommendations on heat treatment of big forgings, for instance, ensuring the necessary complex of mechanical properties are given. Diffusion chromizing with subsequent nitriding of austenitic steels which increase durability of the components in BN reactors more than 4 times, is practised on a large scale

G4beamline Simulations for H8

CERN Document Server

Thoresen, Freja

2015-01-01

Detailed simulations of the H8 beam line at the North Area, using the G4beamline software were performed in the framework of this study. The conventions used by the program are analysed. Having modelled precisely the beam line, several studies examining the beam transmission and composition were performed. The results were compared with measurements, where a satisfactory agreement was found. The muon production and transport is studied in details throughout the beam line.

Serum 8-OHdG and HIF-1α levels: do they affect the development of malignancy in patients with hypoactive thyroid nodules?

Science.gov (United States)

Ece, Harman; Mehmet, Erdogan; Cigir, Biray Avci; Yavuz, Dodurga; Muammer, Karadeniz; Cumhur, Gunduz; Mustafa, Harman; Sevki, Cetinkalp; Fusun, Saygılı; Gokhan, Ozgen Ahmet

2013-01-01

This study aimed to evaluate 8-OHdG and hypoxia-inducible factor 1 (HIF-1α) levels in patients with hypoactive thyroid nodules (toxic multi-nodular goiter, Graves' disease, and Hashimoto's thyroiditis), as these parameters may be related to oxidative stress and the pathogenesis of cancer. The study included patients diagnosed with Graves' disease (n = 20), toxic multinodular goiter (n = 20), and Hashimoto thyroiditis (n = 20), and 20 healthy controls. HIF-1α levels were measured in blood samples and 8-OHdG levels were measured in urine - both via ELISA. HIF-1α and 8-OHdG levels were significantly higher in the patient groups than in the control group (p 0.05). There was no significant difference in 8-OHdG or HIF-1α levels between the patients with biopsy results that were benign, malignant, and non-diagnostic (p > 0.05). Serum HIF-1α and urine 8-OHdG levels were significantly higher in the patients with thyroid diseases; however, a relationship with cancer was not observed.

KH in Paraffin - KH(P): A Useful Base for Organic Synthesis

Science.gov (United States)

Taber, Douglass F.; Nelson, Christopher G.

2011-01-01

The preparation of KH as a one:one homogenate with paraffin, termed KH(P), is reported. KH(P), a solid at room temperature, is stable without special handling. On suspension in THF with a phosphonium salt, KH(P) rapidly generates the ylide. Wittig condensation with aromatic, aliphatic and α, β-unsaturated aldehydes proceeds with high Z-selectivity. KH(P) should be a generally useful base for organic synthesis. PMID:17081034

Quality of the KhN73MBTYu alloy after electroslag remelting and vacuum arc remelting

International Nuclear Information System (INIS)

Shelgaeva, A.V.; Krichevets, M.I.; Shinkina, N.S.; Komissarov, A.I.

1978-01-01

The structure and properties of the heat-resisting KhN73MBTYu alloy are investigated after electroslag remelting (ESR) and vacuum arc (VAR) remelting in commercial furnaces. The complex investigations of the casted metal were carried out by modern methods along with the standard acceptance tests, and a number of service properties were determined. It is established that the ESR metal contains magnesium and has the reduced sulphur concentration; the alloy has more fine-grained structure at high isotropy of the properties at room and operating temperatures; higher endurance is achieved under reversal rotational bending; no laminated fractures are observed. According to the basic quality factors the ESR metal satisfies all requirements for the VAR metal. Due to exclusion of strippling of ESR electrodes and ingots the yield of steel forgings increases by 20-25% and the prime cost decreases in comparison with the industrial production of VAR metal

The potentials of the gauged N=8 supergravity theories

International Nuclear Information System (INIS)

Hull, C.M.

1985-01-01

The potentials of the SO(p,q) gaugings of N=8 supergravity are investigated for critical points. The SO(7,1) gauging has no G 2 -invariant critical points, the SO(6,2) theory has no SU(3) invariant critical points and the SO(5,3) gauging has only one SO(5)-invariant critical point, with positive cosmological constant, SO(5) x SO(3) symmetry and no supersymmetry. (orig.)

C. elegans HIM-8 functions outside of meiosis to antagonize EGL-13 Sox protein function.

Science.gov (United States)

Nelms, Brian L; Hanna-Rose, Wendy

2006-05-15

egl-13 encodes a Sox domain protein that is required for proper uterine seam cell development in Caenorhabditis elegans. We demonstrate that mutations of the C2H2 zinc fingers encoded by the him-8 (high incidence of males) gene partially suppress the egg-laying and connection-of-gonad morphology defects caused by incompletely penetrant alleles of egl-13. him-8 alleles have previously characterized recessive effects on recombination and segregation of the X chromosome during meiosis due to failure of X chromosome homolog pairing and subsequent synapsis. However, we show that him-8 alleles are semi-dominant suppressors of egl-13, and the semi-dominant effect is due to haplo-insufficiency of the him-8 locus. Thus, we conclude that the wild-type him-8 gene product acts antagonistically to EGL-13. Null alleles of egl-13 cannot be suppressed, suggesting that this antagonistic interaction most likely occurs either upstream of or in parallel with EGL-13. Moreover, we conclude that suppression of egl-13 is due to a meiosis-independent function of him-8 because suppression is observed in mutants that have severely reduced meiotic germ cell populations and suppression does not depend on the function of him-8 in the maternal germ line. We also show that the chromosomal context of egl-13 seems important in the him-8 suppression mechanism. Interactions between these genes can give insight into function of Sox family members, which are important in many aspects of metazoan development, and into functions of him-8 outside of meiosis.

Mechanical properties of steel 8 CrMoNiNb 9 10 in dependence on the microstructural condition

International Nuclear Information System (INIS)

Fabritius, H.; Schnabel, E.

1976-01-01

Tension tests at room temperature to 600 0 C and creep-rupture tests at 500 to 600 0 C lasting up to about 75,000 h on two casts of steel 8 CrMoNiNb 9 10 with about 0.08% C, 0.3% Si, 0.7% Mn, 0.012% N, 0.005% Al, 2.34% Cr, 0.95% Mo, 0.8% Nb and 0.64% Ni in bainitic and ferritic microstructural condition. Influence of annealing at 650 to 800 0 C on the properties in the tension test. Influence of aging at 500 to 600 0 C lasting up to 30,000 h with and without mechanical stress on the properties in the tension test at aging temperature and on the toughness behaviour in the notched bar impact bend test at room temperature. (orig.) [de

Development of production technology and investigation of quality for forged-welded turbine rotors of steel 25Kh2NVFA

International Nuclear Information System (INIS)

Borisov, I.A.; Merinov, G.N.; Slezkina, E.V.

1997-01-01

A study was made into mechanical properties and microstructure of turbine rotor components manufactured by forging and heat treated under various conditions. It is revealed that the optimal heat treatment of forgings must include double quenching with subsequent tempering at 630-640 deg C for 10-20 h. Forged and welded rotors should be tempered at 620-630 deg C for 50-100 h. Microscopic examination and mechanical tests showed that low alloy steel 25Kh2NMF can be successfully used for manufacturing rotors of high-, medium-and low-heat turbines

Effect of smelting method on the austenite grain size and properties of heat-resisting pearlitic steel

Energy Technology Data Exchange (ETDEWEB)

Balakhovskaya, M B; Khusainova, N A; Davlyatova, L N [Vsesoyuznyj Nauchno-Issledovatel' skij Teplotekhnicheskij Inst., Moscow (USSR)

1975-12-01

Influence of smelting method on austenite grain size and properties of refractory perlite steel were studied. An opportunity was found to increase the steel refractoriness without deteriorating its other properties. The steel 12Kh1MF of electric or common open-hearth smelting was used. The dependence of kinetics of austenite grain growth on the smelting method was studied in the temperature range 950 deg - 1200 deg C with 1 hour exposure. The grain size of austenite in steel is supposedly determined by aluminium nitrides and vanadium carbides. In tests of normalized (kept for 20 minutes at 950-980 deg C) and tempered (kept for 3 hours at 730 deg C) transverse (tangential) pipe cross-section samples the electric steel had higher impact viscosity than the open-hearth metal. At working temperatures (540 deg -580 deg C) the difference in viscosity has its minimum. Viscosity of both steels 12Kh1MF begins to sharply decrease from 20 deg C. However, electric steel has rather high viscosity even at /sup -/40 deg C, while the open-hearth one becomes brittle as early as at /sup -/20 deg C. Long-term strength tests at 580 deg C under stresses 10-14 kG/mm/sup 2/ show that the coarse-grain steel is more refractory, i.e. time till fracture of open-hearth steel samples is twice as long as that of electric steel samples.

INFORMATION AND RECOMMENDATIONS CONCERNING THE ENLARGED G8 SUMMIT MEETING AT EVIAN

CERN Multimedia

2003-01-01

Despite the difficulties that CERN might encounter, the Organization will pursue its activities for the duration of the G8 Summit Meeting. The Management and Division leaders will take the necessary steps to ensure the proper functioning of the Organization, while taking account of the aforementioned difficulties. The Swiss and French authorities have informed CERN of the following general security and traffic arrangements associated with the enlarged G8 summit: a) Road traffic Between 22 May and 6 June traffic on certain roads in the Canton of Geneva (notably on the left bank) and in neighbouring France (mainly Haute-Savoie) will be disrupted and, in some cases, roads closed. As far as border crossings between 22 May and 4 June are concerned, the frontier posts will be divided into three categories (see map): - posts closed to all traffic (diversion signs will be in place), - posts open at certain times, - posts open at all times. N.B. : the road from Prévessin to Mategnin will be closed and traffic div...

Ab initio investigation of thermodynamic stability and structure of cell molecules B3N4H8 and Be4O4H8

International Nuclear Information System (INIS)

Minyaev, R.M.

2000-01-01

Ab initio calculation methods (RHF/6-31G, MP2(full)/6-31G and MP2(full)/6-311++G) ) are used to investigate thermodynamic stability, energy and structural characteristics of different position isomers of isoelectron B 3 N 4 H 8 (1) and Be 4 O 4 H 8 (2) systems with cubane structure. High thermodynamic stability of these system is shown. Decomposition of structure (1) into two 1,3,2,4-diazadiborethidine molecules or four molecules of iminoborane HBNH is an endothermal process and needs 10.1 (RHF/6-31G), 39/6 (MP2(full)/6-31G) Cal/mol and 140.6 (RHF/6-31G), 161.4 (MP2(full)/6-31G) Cal/mol accordingly. Decomposition of structure (2) into two 1,3,2,4-dioxydiberyllotidine or four molecules of HBeOH is an endothermal process too and needs 22.1 (RHF/6-31G), 39.8 (MP2(full)/6-31G) Cal/mol and 127.1(RHF/6-31G), 155.2 MP2(full)/6-31G) Cal/mol accordingly. Geometrical characteristics of simple BeH 2 , Be 2 , Be 2 H 2 , Be 2 H 4 , BeO, Be 2 O 2 molecules are calculated [ru

Biological profile of 99mTc-HYNIC-βAla-NT(8-13) in MDAMB-231 breast cancer cell line

International Nuclear Information System (INIS)

Teodoro, Rodrigo; Faintuch, Bluma L.; Wiecek, Danielle P.; Silva, Natanael G.; Vallejo, Natalia M.

2009-01-01

Introduction: Neurotensin (NT) is a tridecapeptide involved in several growth-steps of human cancers. Recent studies postulated the role of NT and NT-receptor subtype 1 in breast cancer progression. However, the main drawback of natural NT is its rapid degradation in plasma. In an effort to develop a NT peptide-based radiopharmaceutical for the detection of breast cancer, the aim of this study was the radiolabeling of the double stabilized NT(8-13) peptide using HYNIC as chelating agent. Methods: Conjugated HYNIC-βAla-NT(8-13) was labeled with 99m Tc using tricine and EDDA as coligands. Radiochemical purity was checked by TLC and confirmed by RP-HPLC. 99m Tc-HYNIC-βAla-NT(8-13) (0.1 mL/74 MBq) was administered in Nude mice bearing MDA-MB-231 breast cancer cells and biodistribution studies were carried out at 30 and 90 min postinjection (pi). Blocking evaluation was also conducted by co-injection of 115 nmol of cold NT (8-13) analog. Planar gamma-camera imaging was acquired at the earlier time point studied. Results: Radiochemical purity of the radioconjugate was higher than 99%. Biodistribution studies revealed a very fast accumulation in tumor (1.97±0.18% ID/g, 30 min pi) with a sharply decrease at the later time point studied (0.44±0.02% ID/g). The specificity of the radioconjugate was evaluated with blockade studies. A reduction of 45.94%, 27.73% and 36.39% was found for tumor, large and small intestines, respectively, at 30 min pi. Otherwise, a less impressive blockade was observed for tumor and small intestine (28.68% and 24.90%, respectively) at the later time point studied. Conclusion: The results provide encouraging evidence in the development of radiolabeled NT(8-13) analogues for breast cancer diagnosis. (author)

G8 decision on fusion would herald nuclear future

CERN Multimedia

Starck, Peter

2005-01-01

Nuclear fusion as a future abundant energy source would receive a boost if G8 leaders agree next month on the site for the world's first fusion test reactor, two nuclear scientists said on Wednesday (1 page)

A proposal of parameter to predict biaxial fatigue life for CF8M cast stainless steels

International Nuclear Information System (INIS)

Park, Joong Cheul; Kwon, Jae Do

2005-01-01

Biaxial low cycle fatigue test was carried out to predict fatigue life under combined axial-torsional loading condition which is that of in-phase and out-of-phase for CF8M cast stainless steels. Fatemi Socie(FS) parameter which is based on critical plane approach is not only one of methods but also the best method that can predict fatigue life under biaxial loading condition. But the result showed that, biaxial fatigue life prediction by using FS parameter with several different parameters for the CF8M cast stainless steels is not conservative but best results. So in this present research, we proposed new fatigue life prediction parameter considering effective shear stress instead of FS parameter which considers the maximum normal stress acting on maximum shear strain and its effectiveness was verified

G8+5 collaboration on energy efficiency and IPEEC: Shortcut to a sustainable future?

International Nuclear Information System (INIS)

Lesage, Dries; Van de Graaf, Thijs; Westphal, Kirsten

2010-01-01

In recent years, the G8+5 system has proven to be a major focal point of international cooperation in the field of energy efficiency. The G8 has set up multiple dialogues and collaborative frameworks with five emerging economies (China, India, Brazil, Mexico and South Africa) on energy and energy efficiency. The most prominent initiative so far is the creation of the International Partnership for Energy Efficiency Cooperation (IPEEC) in 2009. This article critically evaluates these joint efforts between the G8 and the 'Plus Five' on energy efficiency. More specifically, the purpose of this article is (1) to frame and explain the emergence of this kind of great-power cooperation; (2) to map G8+5 collaboration on energy efficiency; and (3) to provide a critical assessment of the relevance, impact and results of G8+5 initiated energy efficiency initiatives. The main conclusion is that the G8+5 system has performed better on the external dimension (steering global governance) than on the internal dimension (coordination of domestic policies) of global energy efficiency governance.

Study of effect of austenite prehistory of 03Ch20N16AG6 steel on it structure and properties

Energy Technology Data Exchange (ETDEWEB)

Demchuk, I S; Krakhmalev, V I; Manninen, A I [Leningradskij Politekhnicheskij Inst. (USSR)

1981-01-01

Effect of preliminary cold working and different procedures of thermal treatment on structure and mechanical properties of stable austenite of 03Kh20N16AG6 steel is found out. It is shown that the degree of defectability of initial austenite structure predetermines the further deformation behaviour of the steel (level of strength characteristics, plasticity storage, hardening degree etc.) in the wide temperature range. Close connection of structural changes with properties should determine the choice of preliminary treatment of stable austenitic steel as applied to concrete condition of operation.

Cold-rolled sheets production of stainless martensite-ageing steel smelted by vacuum arc and electroslag techniques

Energy Technology Data Exchange (ETDEWEB)

Rivkin, A A; Grishkov, A I; Suslin, A P; Nesterenko, A A; Lola, V N [Tsentral' nyj Nauchno-Issledovatel' skij Inst. Chernoj Metallurgii, Moscow (USSR)

1975-05-01

In cooperation with a number of metallurgical works the production of a high strength sheet stainless maraging steel EHP678 (000KH11N10M2T) has been tested by rolling cylindrical ingots of vacuum arc smelting at the blooming (the mass of rough ingots was 5.1 to 6.0 t, that of cleaned ingots - 3.8 to 5.1 t) or rectangular ingots of electroslag smelting (13 t) at the slabbing. The recommended regimes of heating and deformation are much similar to those used for the steel-KH18N10T. The output of valid cold-rolled sheets proved to be rather low (0.24 t/t for the vacuum arc smelting and 0.30 t/t for the electroslag smelting) mainly due to the losses on cleaning and a considerable portion of wrong-size slabs. The data are presented on the steel-EHP678 properties after various heat treatments. For the production of wide cold-rolled sheets of the steel EHP678 it is recommended to use steelmaking procedure with electroslag smelting including open-hearth melting in arc furnaces, rolling of ingots at the slabbing with heating up to 1260-1280 deg C (hold-up of 4.5 to 5 hrs); electroslag smelting for rectangular section slabs, rolling of ingots of electroslag smelting at the slabbing with their heating up to 1250 deg C (hold-up of 5.5 to 6 hrs), rolling at the 1680-type mill with heating up to 1250-1260 deg C (hold-up of 4 to 4.5 hrs ensuring the rolling temperature after a rough group not below 1100 deg C), quenching of hot-rolled sheets heating up to 920-940 deg C (hold-up of 3 to 3.5 min/mm), shot peening of sheets for descaling (provided the respective equipment is available) with a subsequent short-time pickling in an acid solution and cold rolling with a summary deformation of 35 to 45 %. The steelmaking with the electroslag smelting is much more profitable as regards to the fine technology of number of the main procedures, convenient cooperation of the works and a considerably greater output of the final products out of one ton of the steel produced.

Comportamiento parabólico del crecimiento de capas boradas en los aceros Y8A y X12M // Parabolic behavior of boriding layers growth in Y8A and X12M steels

Directory of Open Access Journals (Sweden)

C. Figueroa Hernández

1999-01-01

Full Text Available Se determina la influencia que tienen los principales parámetros tecnológicos del borado en el crecimiento de las capas y secorrobora el cumplimiento de la ley parabólica para predecir este comportamiento en los aceros Y8A y X12M.El proceso de borado se aplica en una mezcla de carburo de silicio y bórax (70 y 30 % a la temperatura de 850, 900 y 950 oCdurante un tiempo de 2, 4 y 6 horas. Como variable dependiente se seleccionó la profundidad del recubrimiento, a partir de lacual se obtuvieron los coeficientes del crecimiento parabólico y la energía de activación en función de la temperatura, el tiempodel proceso y el tipo de acero.La caracterización metalográfica reveló la presencia de la fase Fe2BPalabras claves: Borado, recubrimiento superf icial , t ecnología de recubrimiento.__________________________________________________________________________AbstractIt was determined the influence of the main technological parameters of the boriding process, and a mathematical model thatallows to predict this conduct on the steels Y8A and X12M steels was obtained.The boriding process is applied in a mixture of silicon carbide and borax (70 and 30% at 850, 900 and 950 oC temperatureduring a period of time 2, 4 and 6 hours. As an independent variable the depth of the coat was selected.It was obtained the parabolic growth coefficients, and the activation energy according to temperature, time and the chemicalcomposition of steel.Metallografic analysis reveals the presence of Fe2B phase.Key words: Boriding process, superf icial coat , coat technology.

Division algebras and extended N = 2, 4, 8 super KdVs

International Nuclear Information System (INIS)

Carrion, H.L.; Rojas, M.; Toppan, F.

2001-09-01

The first example of an N = 8 supersymmetric extension of the KdV equation is here explicitly constructed. It involves 8 bosonic and 8 fermionic fields. It corresponds to the unique N = 8 solution based a generalized hamiltonian dynamics with (generalized) Poisson brackets given by the Non-associate N = 8 Superconformal Algebra. The complete list of inequivalent classes of parametric-dependent N = 3 and N = 4 superKdVs obtained from the 'Non-associative N= 8 SCA' is also furnished. Furthermore, a fundamental domain characterizing the class of inequivalent N = 4 superKdVs based on the 'minimal N = 4 SCA' is given. (author)

African Journal of Infectious Diseases - Vol 8, No 1 (2014)

African Journals Online (AJOL)

Aspergillus Monitoring Project in a Large Educational Hospital Using Molecular Assay · EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT. K Diba, MH Rahimirad, KH Makhdoomi, NF Eslamloo, 1-4. http://dx.doi.org/10.4314/ajid.v8i1.1 ...

Effect of hot rolling on the structure and the mechanical properties of nitrogen-bearing austenitic-martensitic 14Kh15AN4M steel

Science.gov (United States)

Bannykh, O. A.; Betsofen, S. Ya.; Lukin, E. I.; Blinov, V. M.; Voznesenskaya, N. M.; Tonysheva, O. A.; Blinov, E. V.

2016-04-01

The effect of the rolling temperature and strain on the structure and the properties of corrosionresistant austenitic-martensitic 14Kh15AN4M steel is studied. The steel is shown to exhibit high ductility: upon rolling in the temperature range 700-1100°C at a reduction per pass up to 80%, wedge steel specimens are uniformly deformed along and across the rolling direction without cracking and other surface defects. Subsequent cold treatment and low-temperature tempering ensure a high hardness of the steel (50-56 HRC). Austenite mainly contributes to the hardening upon rolling in the temperature range 700-800°C at a reduction of 50-70%, and martensite makes the main contribution at higher temperatures and lower strains. Texture does not form under the chosen deformation conditions, which indicates dynamic recrystallization with the nucleation and growth of grains having no preferential orientation.

Deletion and aberrant CpG island methylation of Caspase 8 gene in medulloblastoma.

Science.gov (United States)

Gonzalez-Gomez, Pilar; Bello, M Josefa; Inda, M Mar; Alonso, M Eva; Arjona, Dolores; Amiñoso, Cinthia; Lopez-Marin, Isabel; de Campos, Jose M; Sarasa, Jose L; Castresana, Javier S; Rey, Juan A

2004-09-01

Aberrant methylation of promoter CpG islands in human genes is an alternative genetic inactivation mechanism that contributes to the development of human tumors. Nevertheless, few studies have analyzed methylation in medulloblastomas. We determined the frequency of aberrant CpG island methylation for Caspase 8 (CASP8) in a group of 24 medulloblastomas arising in 8 adult and 16 pediatric patients. Complete methylation of CASP8 was found in 15 tumors (62%) and one case displayed hemimethylation. Three samples amplified neither of the two primer sets for methylated or unmethylated alleles, suggesting that genomic deletion occurred in the 5' flanking region of CASP8. Our findings suggest that methylation commonly contributes to CASP8 silencing in medulloblastomas and that homozygous deletion or severe sequence changes involving the promoter region may be another mechanism leading to CASP8 inactivation in this neoplasm.

Propuesta del programaS-GeMS para el análisis estadístico espacial de fallas en alimentadores soterrados de 13,8 kV; PropodedS-GEMS program for statistical analysis of failure space of 13.8 kV underground feeders

Directory of Open Access Journals (Sweden)

Boris Alba Valle

2011-06-01

Full Text Available Actualmente, el sistema soterrado de Ciudad de La Habana, carece de herramientas gráficas de trabajo con lascuales poder visualizar zonas con alta incidencia de fallas en alimentadores de 13,8 kV y que permitan tomardecisiones certeras en cuanto a los tramos de alimentadores a reparar o sustituir por su deterioro. En este trabajo sepropone el uso de los programas S-GeMS (Stanford Geostatistical Modeling Software y Autocad comoherramientas para el análisis estadístico espacial de la cantidad de fallas. Se realiza, en lo fundamental, el estudiode toda la documentación referente a las aplicaciones del programa S-GeMS y la Base de Datos de la cantidad defallas del 2007 al 2009, de los alimentadores de 13,8 kV perteneciente a la Unidad Empresarial Básica (UEBSoterrada. Finalmente se muestran, a modo de ejemplo, los resultados obtenidos con su aplicación al determinarsela dirección preferencial de distribución de la cantidad de fallas.   Nowadays, the Havana City underground system, lacks of graphical working tools which not only allow to visualizehigh faults incidence areas in 13,8 kV feeders but also make good decisions in reference to the feeder sections to berepaired or substituted due to their impairment. The use of S-GeMS (Stanford Geostatistical Modeling Software andAutocad programs as tools for the spatial statistic analysis of faults quantity is proposed in this article. The study ofthe whole documentation related to the S-GeMS program applications is carried out as well as the UndergroundManagement Basic Unit (UEB 13,8 kV feeders faults quantity database from 2007 to 2009. Finally, the results afterdetermining the faults quantity distribution preferential address with the program application are shown, as anexample.

Propuesta del programa S-GeMS para el análisis estadístico espacial de fallas en alimentadores soterrados de 13,8 kV;PropodedS-GEMS program for statistical analysis of failure space of 13.8 kV underground feeders

Directory of Open Access Journals (Sweden)

Boris Alba - Valle

2011-06-01

Full Text Available Actualmente, el sistema soterrado de Ciudad de La Habana, carece de herramientas gráficas de trabajo con lascuales poder visualizar zonas con alta incidencia de fallas en alimentadores de 13,8 kV y que permitan tomardecisiones certeras en cuanto a los tramos de alimentadores a reparar o sustituir por su deterioro. En este trabajo sepropone el uso de los programas S-GeMS (Stanford Geostatistical Modeling Software y Autocad comoherramientas para el análisis estadístico espacial de la cantidad de fallas. Se realiza, en lo fundamental, el estudiode toda la documentación referente a las aplicaciones del programa S-GeMS y la Base de Datos de la cantidad defallas del 2007 al 2009, de los alimentadores de 13,8 kV perteneciente a la Unidad Empresarial Básica (UEBSoterrada. Finalmente se muestran, a modo de ejemplo, los resultados obtenidos con su aplicación al determinarsela dirección preferencial de distribución de la cantidad de fallas.Nowadays, the Havana City underground system, lacks of graphical working tools which not only allow to visualizehigh faults incidence areas in 13,8 kV feeders but also make good decisions in reference to the feeder sections to berepaired or substituted due to their impairment. The use of S-GeMS (Stanford Geostatistical Modeling Software andAutocad programs as tools for the spatial statistic analysis of faults quantity is proposed in this article. The study ofthe whole documentation related to the S-GeMS program applications is carried out as well as the UndergroundManagement Basic Unit (UEB 13,8 kV feeders faults quantity database from 2007 to 2009. Finally, the results afterdetermining the faults quantity distribution preferential address with the program application are shown, as anexample.

13 CFR 124.509 - What are non-8(a) business activity targets?

Science.gov (United States)

2010-01-01

... non-8(a) business activity targets. These include requiring the Participant to obtain management..., business development, financing, marketing, accounting, or proposal preparation. (5) SBA may initiate... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false What are non-8(a) business...

Measurements of the 40Ar(n, γ41Ar radiative-capture cross section between 0.4 and 14.8 MeV

Directory of Open Access Journals (Sweden)

Megha Bhike

2014-09-01

Full Text Available The 40Ar(n, γ41Ar neutron capture cross section has been measured between 0.4 and 14.8 MeV neutron energy using the activation technique. The data are important for estimating backgrounds in argon-based neutrino and dark-matter detectors and in the neutrino-less double-beta decay search GERDA, which uses liquid argon as cooling and shielding medium. For the first time the 40Ar(n, γ41Ar cross section has been measured for neutron energies above 1 MeV. Our results are compared to the evaluation ENDF/B-VII.1 and the calculated prediction TENDL-2013. The latter agrees very well with the present results.

Aircraft Steels

Science.gov (United States)

2009-02-19

component usage. PH 13-8Mo is a precipitation-hardenable martensitic stainless steel combining excellent corrosion resistance with strength. Custom 465 is...a martensitic , age-hardenable stainless steel capable of about 1,724 MPa (250 ksi) UTS when peak-aged (H900 condition). Especially, this steel can...NOTES 14. ABSTRACT Five high strength steels (4340, 300M, AerMet 100, Ferrium S53, and Hy-Tuf) and four stainless steels (High Nitrogen, 13

Grains Are Similarly Categorized by 8- to 13-Year-Old Children

Science.gov (United States)

Beltran, Alicia; Sepulveda, Karina Knight; Watson, Kathy; Baranowski, Tom; Baranowski, Janice; Islam, Noemi; Missaghian, Mariam

2009-01-01

This study assessed how 8- to 13-year-old children categorized and labeled grain foods and how these categories and labels were influenced by child characteristics. The main hypotheses were that children categorized foods in consistent ways and these food categories differed from the professional food categories. A set of 71 cards with pictures and names of grain foods from eight professionally denned food groups was sorted by each child into piles of similar foods. There were 149 8- to 13-year-old children (133 English-speaking, 16 Spanish-speaking) in this exploratory study. One-way analysis of variance and Robinson matrices for identification of clusters of food items were calculated. Children created a mean (± standard deviation) of 8.3±3.8 piles with 8.6±9.1 cards per pile. No substantial differences in Robinson clustering were detected across subcategories for each of the demographic characteristics. For the majority of the piles, children provided “taxonomic-professional” (34.5%) labels, such as bread for the professional category of breads, rolls, and tortillas, or “script” (26.1%) labels, such as breakfast for the professional category of pancakes, waffles, and flapjacks. These categories may be used to facilitate food search in a computerized 24-hour dietary recall for children in this age group. PMID:18954585

MLEP-Fail calibration for 1/8 inch thick cast plate of 17-4 steel.

Energy Technology Data Exchange (ETDEWEB)

Corona, Edmundo [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2018-02-01

The purpose of the work presented in this memo was to calibrate the Sierra material model Multilinear Elastic-Plastic Hardening Model with Failure (MLEP-Fail) for 1/8 inch thick cast plate of 17-4 steel. The calibration approach is essentially the same as that recently used in a previous memo using data from smooth and notched tensile specimens. The notched specimens were manufactured with three notch radii R = 1=8, 1/32 and 1/64 inches. The dimensions of the smooth and notched specimens are given in the prints in Appendix A. Two cast plates, Plate 3 and Plate 4, with nominally identical properties were considered.

Interventional bleeding, hematoma and scar-formation after vacuum-biopsy under stereotactic guidance: Mammotome®-system 11g/8g vs. ATEC®-system 12g/9g

International Nuclear Information System (INIS)

Schaefer, F.K.W.; Order, B.M.; Eckmann-Scholz, C.; Strauss, A.; Hilpert, F.; Kroj, K.; Biernath-Wüpping, J.; Heller, M.; Jonat, W.; Schaefer, P.J.

2012-01-01

Purpose: To evaluate prospectively the correlation of scar-formations after vacuum-assisted biopsy with different systems and needle-sizes and interventional bleeding/post-interventional hematoma. Methods and materials: Between 01/2008 and 12/2009, 479 patients underwent vacuum-assisted biopsy under stereotactic-guidance, using the Mammotome ® -system with 11/8-gauge and ATEC ® -system with 12/9-gauge, whereas in 178 cases with representative benign histology no surgical-biopsy after vacuum-assisted biopsy was performed and at least a 2-plane-follow-up-mammogram after 6 month post-vacuum-assisted biopsy was available. Bleeding during intervention, hematoma post-intervention and scar-tissue was scored as minimal and moderate/severe. Statistical analysis included Chi-Square-trend-test, p-value ® -system vs. 11-gauge-Mammotome ® -system (41.9% vs. 8.4%, p ® -systems 9-gauge vs. 12-gauge (26.9% vs. 29.7%, p = 0.799/42.3% vs. 43.2%, p = 0.596). 11-gauge-Mammotome ® -system vs. ATEC ® -12-gauge-system revealed significantly less bleedings/hematomas (8.4% vs. 29.7%, p = 0.015/16.7% vs. 43.2%, p = 0.001), no significant differences for the large-systems (p = 0.135/p = 0.352). Follow-up of Mammotome ® -11/8-gauge-system system has shown 13.1/16.1% minimal scar-formation and 1.2/3.2% moderate/severe scars, whereas ATEC ® -12/9-gauge-system has shown 10.8/3.8% minimal scar-formation and 0/11.5% moderate/severe scars, no significant differences. No significant difference was found when comparing Mammotome ® -11/8-g-systems vs. ATEC ® -12/9-g-systems (p = 0.609/p = 0.823). There was also no correlation between risk of scar-formation after occurrence of bleeding or hematoma with any examined VAB-system or any needle size in this study (p = 0.800). Conclusion: Using larger needle-sizes significantly (Mammotome ®) /not significant for ATEC ® ) more interventional bleedings and post-interventional hematomas were detected, only a tendency concerning scar-formation.

Industrial culture media optimization for acetrobutilic Fermentation Optimización de un medio de cultivo industrial para la fermentación acetobutilica (abe

Directory of Open Access Journals (Sweden)

Ramos J.

1999-12-01

Full Text Available The industrial culture media for butanol-ethanol-acetone fermentation (ABE was optimized by experimental design. A butanol resistant mutant isolated from Clostridium acetobutylicum DSM 1732 was used. This mutant produced 15.5 g/1 of total solvents, 30% more than the wild strain solvent production. Mutant strain resists a concentration of 2,5% v/v meanwhile the type strain resists 1 % v/v butanol concentration. Molasses of sugar cane as carbon source were used. The molasses concentration was determined based on the necessary glucose concentration for producing 15 g/1 of butanol as limit product in the ABE fermentation. The nutrients were calculated in according lo literature reports and lo highest biomasse production on vegetative medium 3.8g/l. For determining which variables have significant effect on the total solvent production, the PLAKET-BURMAN method was used. The final concentrations of the culture medium were determined by EVOP-Simplex method. A liter of optimized industrial medium is composed by: molasses 130 g, biotin 4.0 mg, PAB A 3.0 mg, KH2PO41.8 g, yeast extract 3.0 g, minerals stock 4 ml and distilled water lo complete 1 liter; pH 6.1 before sterilization. Using this medium the total solvents production was 24,6 g/1. The production increment is equivalent lo 58,7%, compared lo the mutant strain before the medium was optimized. En el presente trabajo se optimizó un medio de cultivo industrial para la fermentación acetobutilica (ABE mediante la aplicación de diseño de experimentos. Se empleó una mutante espontánea resistente al butanol aislada de la cepa de Clostridium acetobutylicum DSM 1732 la cual tolera una concentración de butanol de 2.5% v/v. La mutante produce 15.5 g/1 de solventes totales que representan 30% más que la cepa silvestre. Para diseñar el medio se empleó como fuente de carbono, melazas de caña. Los nutrientes se calcularon de acuerdo con la máxima cantidad de biomasa obtenida en medio vegetativo (3.8

The southern molecular environment of SNR G18.8+0.3

OpenAIRE

Paron, S.; Peña, M. Celis; Ortega, M. E.; Petriela, A.; Dubner, G.; Giacina, E.; Rubio, M.

2015-01-01

In a previous paper we have investigated the molecular environment towardsthe eastern border of the SNR G18.8+0.3. Continuing with the study of thesurroundings of this SNR, in this work we focus on its southern border, whichin the radio continuum emission shows a very peculiar morphology with acorrugated corner and a very flattened southern flank. We observed two regionstowards the south of SNR G18.8+0.3 using the Atacama Submillimeter TelescopeExperiment (ASTE) in the 12CO J=3-2. One of thes...

Environmental Fatigue Behaviors of CF8M Stainless Steel in 310 .deg. C Deoxygenated Water - Effects of Hydrogen and Microstructure

Energy Technology Data Exchange (ETDEWEB)

Jang, Hun; Cho, Pyungyeon; Jang, Changheui [KAIST, Daejeon (Korea, Republic of); Kim, Tae Soon [Korea Hydro and Nuclear Power Corporation, Seoul (Korea, Republic of)

2014-01-15

The effects of environment and microstructure on low cycle fatigue (LCF) behaviors of CF8M stainless steels containing 11% of ferrites were investigated in a 310 .deg. C deoxygenated water environment. The reduction of LCF life of CF8M in a 310 .deg. C deoxygenated water was smaller than 316LN stainless steels. Based on the microstructure and fatigue surface analyses, it was confirmed that the hydrogen induced cracking contributed to the reduction in LCF life for CF8M as well as for 316LN. However, many secondary cracks were found on the boundaries of ferrite phases in CF8M, which effectively reduced the stress concentration at the crack tip. Because of the reduced stress concentration, the accelerated fatigue crack growth by hydrogen induced cracking was less significant, which resulted in the smaller environmental effects for CF8M than 316LN in a 310 .deg. C deoxygenated water.

Gauged N=8 supergravity in five dimensions

International Nuclear Information System (INIS)

Guenaydin, M.; Romans, L.J.; Warner, N.P.

1985-01-01

We construct gauged N=8 supergravity theories in five dimensions. Instead of the twenty-seven vector fields of the ungauged theory, the gauged theories contain fifteen vector fields and twelve second-rank antisymmetric tensor fields satisfying self-dual field equations. The fifteen vector fields can be used to gauge any of the fifteen-dimensional semisimple subgroups of SL(6, R), sepcifically SO(p, 6-p) for p=0, 1, 2, 3. The gauged theories also have a physical global SU(1,1) symmetry which survives from the Esub(6(6)) symmetry of the ungauged theory. This SU(1, 1) for the SO(6) gauging is presumably related to that of the chiral N=2 theory in ten dimensions. In our formalism we maintain a composite local USp(8) symmetry analogous to SU(8) in four dimensions. (orig.)

Biological profile of {sup 99m}Tc-HYNIC-betaAla-NT(8-13) in MDAMB-231 breast cancer cell line

Energy Technology Data Exchange (ETDEWEB)

Teodoro, Rodrigo; Faintuch, Bluma L.; Wiecek, Danielle P.; Silva, Natanael G.; Vallejo, Natalia M., E-mail: teodoro_rodrigo@yahoo.com.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Diretoria de Radiofarmacia

2009-07-01

Introduction: Neurotensin (NT) is a tridecapeptide involved in several growth-steps of human cancers. Recent studies postulated the role of NT and NT-receptor subtype 1 in breast cancer progression. However, the main drawback of natural NT is its rapid degradation in plasma. In an effort to develop a NT peptide-based radiopharmaceutical for the detection of breast cancer, the aim of this study was the radiolabeling of the double stabilized NT(8-13) peptide using HYNIC as chelating agent. Methods: Conjugated HYNIC-betaAla-NT(8-13) was labeled with {sup 99m}Tc using tricine and EDDA as coligands. Radiochemical purity was checked by TLC and confirmed by RP-HPLC. {sup 99m}Tc-HYNIC-betaAla-NT(8-13) (0.1 mL/74 MBq) was administered in Nude mice bearing MDA-MB-231 breast cancer cells and biodistribution studies were carried out at 30 and 90 min postinjection (pi). Blocking evaluation was also conducted by co-injection of 115 nmol of cold NT (8-13) analog. Planar gamma-camera imaging was acquired at the earlier time point studied. Results: Radiochemical purity of the radioconjugate was higher than 99%. Biodistribution studies revealed a very fast accumulation in tumor (1.97+-0.18% ID/g, 30 min pi) with a sharply decrease at the later time point studied (0.44+-0.02% ID/g). The specificity of the radioconjugate was evaluated with blockade studies. A reduction of 45.94%, 27.73% and 36.39% was found for tumor, large and small intestines, respectively, at 30 min pi. Otherwise, a less impressive blockade was observed for tumor and small intestine (28.68% and 24.90%, respectively) at the later time point studied. Conclusion: The results provide encouraging evidence in the development of radiolabeled NT(8-13) analogues for breast cancer diagnosis. (author)

N = 8 BPS black holes preserving 1/8 supersymmetry

Science.gov (United States)

Bertolini, M.; Frè, P.; Trigiante, M.

1999-05-01

In the context of N = 8 supergravity we consider BPS black holes that preserve 1/8 supersymmetry. It was shown in a previous paper that, modulo U-duality transformations of E7(7), the most general solution of this type can be reduced to a black hole of the STU model. In this paper we analyse this solution in detail, considering in particular its embedding in one of the possible special Kähler manifolds compatible with the consistent truncations to N = 2 supergravity, this manifold being the moduli space of the T6/icons/Journals/Common/BbbZ" ALT="BbbZ" ALIGN="MIDDLE"/>3 orbifold, that is SU(3,3)/SU(3) × U(3). This construction requires a crucial use of the solvable Lie algebra formalism. Once the group-theoretical analysis is done, starting from a static, spherically symmetric ansatz, we find an exact solution for all the scalars (both dilaton- and axion-like) and for gauge fields, together with their already known charge-dependent fixed values, which yield a U-duality-invariant entropy. We also give a complete translation dictionary between the solvable Lie algebra and the special Kähler formalisms in order to allow a more immediate comparison with other papers on similar issues. Although the explicit solution is given in a simplified case where the equations turn out to be more manageable, it encodes all the features of the more general one, namely it has non-vanishing entropy and the scalar fields have a non-trivial radial dependence.

Hot reactions of 13N in solid methane at 77 K

International Nuclear Information System (INIS)

Fiergolla, J.; Nebeling, B.; Roessler, K.

1987-09-01

The chemical reactions of recoil- 13 N were studied in solid methane at 77 K. 13 N was generated via the the nuclear reaction 12 C(d,n) 13 N. The radiation dose deliverd by the 8.5 MeV deuterons amounted to D * = 0.6 eV per target molecule. The products formed by high energy chemical processes (hot chemistry) were analyzed by radio-gaschromatography. 13 NH 3 with 52% and CH 3 13 NH 2 with 25% radiochemical yield were found to be the main products. HC 13 N was not formed, but CH 3 13 CN amounts to 4%. For the more complex products carbon chain prolongation is prefered over multiple methylation such as show the yields of 8% for C 2 H 5 13 NH 2 and 3% (CH 3 ) 2 13 NH. (CH 3 ) 3 N was not detected. The formation of 13 NH 3 is due to hydrogen abstraction, that of CH 3 13 NH 2 due to insertion of NH radical into the C-H bond of CH 4 . Another, however, less probable pathway could be the insertion of 13 N into methane. The methylamine radical may react with another methane molecule via hydrogen transfer to methylamine or attack to CH 4 to dimethylamine. The 13 N-products were formed with high radiochemical purity and can potentially be applied for the synthesis of 13 N-radiopharmaceuticals. The reactions studied bear also informations on chemical processes in space (e.g. solar wind interactions with comets or interplanetary dust). 13 N-high energy chemical products are, however, of a less exobiological significance then those formed by hot carbon atoms, e.g. in the 'mirror' system 11 C/NH 3 (s). (orig.) [de

Cross section measurements for gallium in the neutron energy range of 13.5 to 14.8 MeV

Energy Technology Data Exchange (ETDEWEB)

Luo, J. [Hexi Univ., Zhangye (China). School of Physics and Electromechanical Engineering; Liu, R.; Jiang, L. [Chinese Academy of Engineering Physics, Mianyang (China). Inst. of Nuclear Physics and Chemistry

2012-07-01

Cross sections for (n, 2n), (n, p) and (n, n'{alpha}) reactions have been measured on gallium isotopes at the neutron energies of 13.5-14.8 MeV using the activation technique. The monoenergetic neutron beam was produced via the {sup 3}H(d, n){sup 4}He reaction. The neutron fluences were determined using the monitor reaction {sup 27}Al(n, {alpha}){sup 24}Na. The activities induced in the reaction products were measured using high-resolution gamma-ray spectrometry. Data are reported for the following reactions: {sup 69}Ga(n, 2n){sup 68}Ga, {sup 71}Ga(n, 2n) {sup 70}Ga, {sup 69}Ga(n, p){sup 69m}Zn, {sup 71}Ga(n, p){sup 71m}Zn and {sup 71} Ga(n, n'{alpha}){sup 67}Cu. Nuclear model calculations using the code HFTT, which employs the Hauser-Feshbach (statistical model) and exciton model (precompound effects) formalisms, were undertaken to describe the formation of the reaction products. Results are discussed and compared with some corresponding values found in the literature, with some established systematics and with the evaluated data given in ENDF/B-VII.0, CENDL-3.1 and JENDL-4.0. (orig.)

Preclinical evaluation of a new, stabilized neurotensin(8--13) pseudopeptide radiolabeled with (99m)tc.

Science.gov (United States)

García-Garayoa, Elisa; Bläuenstein, Peter; Bruehlmeier, Matthias; Blanc, Alain; Iterbeke, Koen; Conrath, Peter; Tourwé, Dirk; Schubiger, P August

2002-03-01

The rapid degradation of neurotensin (NT) limits its clinical use in cancer imaging and therapy. Thus, a new NT(8--13) pseudopeptide, NT-VIII, was synthesized. Some changes were introduced in the sequence of NT(8--13) to stabilize the molecule against enzymatic degradation: Arg(8) was N-methylated, and Lys and Tle replaced Arg(9) and Ile(12), respectively. Finally, (NalphaHis)Ac was coupled to the N-terminus for (99m)Tc(CO)(3) labeling. This peptide was characterized both in vitro and in vivo. The new analog was labeled with (99m)Tc(CO)(3). Its metabolic stability was analyzed both in human plasma and in HT-29 cells. Binding properties, receptor downregulation, and internalization were tested with HT-29 cells. Biodistribution was evaluated in nude mice with HT-29 xenografts. (99m)Tc(CO)(3)NT-VIII showed a high stability in plasma, where most of the peptide remained intact after 24 h of incubation at 37 degreesC. However, the degradation in HT-29 cells was more rapid (46% of intact (99m)Tc(CO)(3)NT-VIII after 24 h at 37 degreesC). Binding to NT1 receptors (NTR1) was saturable and specific. Scatchard analysis showed a high affinity for (99m)Tc(CO)(3)NT-VIII, with a dissociation constant similar to (125)I-NT (1.8 vs. 1.6 nmol/L). After interacting with NTR1, (99m)Tc(CO)(3)NT-VIII was rapidly internalized, with more than 90% internalized after 30 min. It also distributed and cleared rapidly in nude mice bearing HT-29 xenografts. The highest rates of accumulation were found in kidney and tumor at all time points tested. Tumor uptake was highly specific because it could be blocked by coinjection with a high dose of (NalphaHis)Ac-NT(8--13). Tumors were clearly visualized in scintigraphy images. The changes that were introduced stabilized the molecule against enzymatic degradation without affecting binding properties. Moreover, the increase in stability enhanced tumor uptake, making this derivative a promising candidate for clinical use.

External corrosion of tanks 8D-1 and 8D-2. Final report

International Nuclear Information System (INIS)

Mackey, D.B.; Westerman, R.E.

1995-05-01

Tanks 8D-1 and 8D-2 at the West Valley Nuclear Services (WVNS) site, West Valley, New York, rest on layers of perlite brick contained within steel pans. The pans tend to collect water, which can contact the tanks directly and which also can be ''wicked'' to the external surfaces of the tank through the perlite brick. The presence of air in the tank vault is conducive to the formation of oxygen concentration cells, which can promote localized corrosion of the carbon steel tank wall. Pacific Northwest Laboratory conducted an experiment to estimate the extent to which the external surfaces of the tanks could have corroded in the 30 years since their construction. Specimens of carbon steel, similar to that used in the tank construction, were partially embedded in an upright position in particulate perlite in closed containers. The water line in the containers.was maintained at two levels: above the perlite level (high water level tests) and below the bottoms of the specimens (low water level tests). The water used in the tests was obtained from the pan of tank 8D-1. The containers were maintained in an aerated condition. Specimens were examined after 3-, 6-, 12-, 18-, 24-, and 30-month exposures

40 CFR 76.8 - Early election for Group 1, Phase II boilers.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 16 2010-07-01 2010-07-01 false Early election for Group 1, Phase II boilers. 76.8 Section 76.8 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) ACID RAIN NITROGEN OXIDES EMISSION REDUCTION PROGRAM § 76.8 Early election for Group 1...

15 CFR 13.8 - Opportunity to comment on proposed Federal financial assistance and direct Federal development.

Science.gov (United States)

2010-01-01

... 15 Commerce and Foreign Trade 1 2010-01-01 2010-01-01 false Opportunity to comment on proposed Federal financial assistance and direct Federal development. 13.8 Section 13.8 Commerce and Foreign Trade Office of the Secretary of Commerce INTERGOVERNMENTAL REVIEW OF DEPARTMENT OF COMMERCE PROGRAMS AND ACTIVITIES § 13.8 Opportunity to comment on...

Investigation of Creep Processes and Microdamages in 10Kh9V2MFBR-Sh High-Chromium Steel

Science.gov (United States)

Grin', E. A.; Pchelintsev, A. V.

2018-01-01

During the modernization and the new construction of power units at TPPs in Russia, high-chromium martensitic steels with higher heat-resistant properties than the traditional perlite steels are increasingly used as structural materials. High-chromium steels have a necessary regulatory support for their use in domestic power engineering. However, up to the present time, the issue of assessing the quality of these steels at the analysis of their state during long-term operation remains open. The article proposed is one of the first attempts to create a system of quality criteria for martensitic steels based on their microdamage parameters. Tests were carried out on the long-term strength and creep of samples from 10Kh9V2MFBR-Sh steel at high temperatures with the construction of creep curves in relative coordinates "deformation related to the deformation of fracture, current time related to time to failure." For some samples, the tests were interrupted and the metal was subjected to metallographic studies consisting of the analysis of microdamage with reference to the accumulated creep strain. It has been shown experimentally that the deformation curve of high-chromium steel differs from the analogous curve of pearlitic steel by a longer and flat section of steady creep and by a sharper transition to the third accelerated creep stage, which has a very short time period (approximately 10% of the total durability). The tendency to the increase in the microdamage of the structure of steel as the accumulated creep strain increases with time was confirmed. The beginning of transition to the final creep phase is characterized by the formation of contours of future pore chains and by the appearance of individual large pores of up to 6 μm in size, the presence of which in the microstructure of the martensitic steel indicates a very significant accumulation of creep strain, and corresponds to the predestruction stage of metal. It is necessary to continue the research to

On the low-cycle fracture of chromium-nickel-molybdenum structural steels in seawater

International Nuclear Information System (INIS)

Karpenko, G.V.; Kobzaruk, A.V.; Malyshevskij, V.A.; Shul'te, A.Yu.; Rybin, V.V.; Silaev, I.I.

1977-01-01

The processes of low-cycle fracture of the chrome-nickel-molybdenum steels 15KhN5MF, 12KhN4MF and 15KhN3M in air, and in sea water have been investigated by the optical microscopy method, and electron microscopic examination of thin films. Bringing no change in the fracture character, sea water produces a speeding-up effect on the low-cycle fatigue fracture process. During long-time corrosion fatigue testing considerable importance lies with the electrochemical corrosion factor expediting the occurrence of corrosive pits acting as crack-initiation nuclei, fatigue crack attack, accumulation of corrosion products in fatigue cracks, etc

Effect of processing variables on mechanical properties of sintered manganese steels Fe-3%Mn-0.8%C

International Nuclear Information System (INIS)

Sulowski, M.; Cias, A.

1998-01-01

The powder metallurgy route may allow sintered manganese steels to be made based on pure iron powder and ferromanganese powder with control over alloy microstructure. The factors that contribute to the mechanical properties of sintered Fe-3%Mn-0.8%C manganese steel, such as the sintering atmosphere, dew point, sintering temperature, cooling rate are summarised. The paper shows the influence of these parameters on the tensile strength, yield strength, transverse rupture strength, impact strength and hardness. It is showed that tensile high strength level higher than those of many present sintered steels can be obtained already in the as-sintered condition. (author)

The G8 global partnership against proliferation

International Nuclear Information System (INIS)

Devaux, O.

2003-01-01

Launched in 2002, the G8 global partnership against the proliferation of massive destruction weapons will contribute up to 20 billion dollars to the dismantling of the nuclear and chemical weapons of the former USSR (20000 nuclear warheads stored in 123 sites, 1350 tons of weapon grade plutonium and enriched uranium, 40000 tons of chemical agents, 190 decommissioned nuclear submarines etc..). This partnership, which has entered its realization phase, inaugurates a new cooperation with the Russian Federation. I could be used tomorrow in other regions of the world and become an instrument of the international community for the fight against proliferation. (J.S.)

G8 global partnership. France's contribution

International Nuclear Information System (INIS)

2005-09-01

During the G8 summit at Kananaskis (Canada) in June 2002, G8 Leaders decided to launch the Global Partnership against the Spread of Weapons and Materials of Mass Destruction. Under this initiative, partners support specific cooperation projects to address non-proliferation, disarmament, counter-terrorism and nuclear safety issues. Since then, thirteen other donor countries have joined the initiative from which the Ukraine may also now benefit. France intends to make an effective contribution, up to 750 million euros, to the implementation of this initiative, giving priority to a genuine partnership between France and Russia covering projects in the nuclear, chemical and biological fields. France intends to be involved in the various fields identified at Kananaskis: in the nuclear field, it is participating in nuclear submarine dismantling actions and contributes to the improvement of nuclear safety and security. It also supports the program for the disposition of Russian weapons-grade plutonium designated as no longer required for defence purposes. France is also involved in the destruction of chemical weapons and intends to develop responses to bio-terrorist threats, while promoting reemployment of scientists. To optimise its action, France has committed itself to both multilateral and bilateral programs. In the multilateral framework, France contributes to: - the NDEP fund (Northern Dimension Environment Partnership) which will finance projects related to the dismantling of nuclear submarines and remediation of the sites concerned; - the MPDG (Multilateral Plutonium Disposition Group), whose objective is to enable the disposition of Russian weapons-grade plutonium designated as no longer required for defence purposes; - the construction of the new Chernobyl shelter in the Ukraine. France is also developing bilateral cooperation, primarily with Russia: - in the nuclear field, the implementing agreement negotiated in the framework of the Multilateral Environmental

Inhibitor effect on corrosion of titanium alloys in muriatic solutions of titanium-magnesium production

International Nuclear Information System (INIS)

Dobrunov, Yu.V.; Volynskij, V.V.; Kolobov, G.A.; Kuznetsov, S.I.

1977-01-01

Corrosion tests of titanium alloys VTI-0, OT4, VT5-1 and steel Kh18N1OT in 10% and 18% HCl with additions of carnallite at 40 deg C have been carried out. It has been established that titanium alloys in 10% and 18% HCl containing 5 and 10% carnallite are sufficiently corrosion resistant in the presence of 0.1-1% FeCl or HNO 3 and can be used for manufacturing the equipment of recirculation gas scrubbers. Steel Kh18N10T is unstable in all the media tested. It is subjected to intensive pitting. Specimens of steel Kh18N10T have also revealed edge cracking

Study of nitrogen solubility in multicomponent iron alloys at its pressure in gaseous phase up to 1000kPa

International Nuclear Information System (INIS)

Pomarin, Yu.M.; Grigorenko, G.M.; Latash, Yu.V.; Kanibolotskij, S.A.

1983-01-01

A facility in which metal is melted in a weighed state and nitrogen partical pressure during relting may be charge from 0 to 1000 kPa is developed to investigate nitrogen solubility is liquim metals and alloys. Investigation of nitrogen solubility was performed using samples of 03Kh25N5AM3 steel and Kh20N5, Kh20N10, Kh40N10, Kh40N20 alloys. Positive deflection of [N]=f(√Psub(Nsub(2))) dependence from the Henry law is shown to be observed in the Kh40N10 alloy in the 100-1000 kPa pressure range. In this case the vatue of positive deflection decreases with temperature growth and at T=2273 K nitrogen solubility in the alloy submits to the law of square root. An equation permitting to calculate nitrogen solubility in alloys of Fe-Cr-Ni and Fe-Cr-Mn systems in the 0 to 1000 kPa range of nitrogen partial pressures is obtained

Analysis of Human TAAR8 and Murine Taar8b Mediated Signaling Pathways and Expression Profile

Directory of Open Access Journals (Sweden)

Jessica Mühlhaus

2014-11-01

Full Text Available The thyroid hormone derivative 3-iodothyronamine (3-T1AM exerts metabolic effects in vivo that contradict known effects of thyroid hormones. 3-T1AM acts as a trace amine-associated receptor 1 (TAAR1 agonist and activates Gs signaling in vitro. Interestingly, 3-T1AM-meditated in vivo effects persist in Taar1 knockout-mice indicating that further targets of 3-T1AM might exist. Here, we investigated another member of the TAAR family, the only scarcely studied mouse and human trace-amine-associated receptor 8 (Taar8b, TAAR8. By RT-qPCR and locked-nucleic-acid (LNA in situ hybridization, Taar8b expression in different mouse tissues was analyzed. Functionally, we characterized TAAR8 and Taar8b with regard to cell surface expression and signaling via different G-protein-mediated pathways. Cell surface expression was verified by ELISA, and cAMP accumulation was quantified by AlphaScreen for detection of Gs and/or Gi/o signaling. Activation of G-proteins Gq/11 and G12/13 was analyzed by reporter gene assays. Expression analyses revealed at most marginal Taar8b expression and no gender differences for almost all analyzed tissues. In heart, LNA-in situ hybridization demonstrated the absence of Taar8b expression. We could not identify 3-T1AM as a ligand for TAAR8 and Taar8b, but both receptors were characterized by a basal Gi/o signaling activity, a so far unknown signaling pathway for TAARs.

Fabrication of welded pipes of the KhN45Yu alloy

International Nuclear Information System (INIS)

Lyapunov, A.I.; Krichevskij, E.M.; L'vov, V.N.; Kozlov, N.N.; Kireeva, T.S.

1977-01-01

A highly heat-resistant KhN45Yu (EP 747) alloy has been developed; the alloy is designed to withstand prolonged service in the temperature range of 1000-1300 deg C, or short-term service at 1300-1400 deg C. The satisfactory ductility and good weldability of the alloy have made it possible to obtain sheets and pipes (32 x 2.0 mm) by argon arc welding. The ductility of pipes from EP 747 alloy exceeds that of pipes from KhN78T (EI 435) alloy by 5.10%, the strength being approximately equal. In regard to strength the welded joint differs little from the base metal. The ductility characteristics up to 900 deg C are also equal, since failure occurs in the base metal. At higher temperatures the welded joint fails in the metal of the weld, and its ductility drops sharply. The grain size of the base metal corresponds to No. 3-4. The welded joint has a cast structure with a grain size larger than No. 1, but its ductility characteristics are satisfactory. This structure ensures an increased long-term strength of the material at 1000-1200 deg C

Inhibition of a NEDD8 Cascade Restores Restriction of HIV by APOBEC3G.

Directory of Open Access Journals (Sweden)

David J Stanley

2012-12-01

Full Text Available Cellular restriction factors help to defend humans against human immunodeficiency virus (HIV. HIV accessory proteins hijack at least three different Cullin-RING ubiquitin ligases, which must be activated by the small ubiquitin-like protein NEDD8, in order to counteract host cellular restriction factors. We found that conjugation of NEDD8 to Cullin-5 by the NEDD8-conjugating enzyme UBE2F is required for HIV Vif-mediated degradation of the host restriction factor APOBEC3G (A3G. Pharmacological inhibition of the NEDD8 E1 by MLN4924 or knockdown of either UBE2F or its RING-protein binding partner RBX2 bypasses the effect of Vif, restoring the restriction of HIV by A3G. NMR mapping and mutational analyses define specificity determinants of the UBE2F NEDD8 cascade. These studies demonstrate that disrupting host NEDD8 cascades presents a novel antiretroviral therapeutic approach enhancing the ability of the immune system to combat HIV.

40 CFR 64.8 - Quality improvement plan (QIP) requirements.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 15 2010-07-01 2010-07-01 false Quality improvement plan (QIP... PROGRAMS (CONTINUED) COMPLIANCE ASSURANCE MONITORING § 64.8 Quality improvement plan (QIP) requirements. (a.... (iii) Appropriate improvements to control methods. (iv) Other steps appropriate to correct control...

Reliability and durability of the 12Kh1MF steel tubes of electroslag remelting and their welded joints

International Nuclear Information System (INIS)

Lanskaya, K.A.; Kulikova, L.V.; Mazel', R.E.; Khromchenko, F.A.; Strizhenova, V.F.

1978-01-01

Results of investigating the positive effect of electrolag remelting (ESR) on the properties of the base metal and welded joint of the 12Kh1MF steel steam pipes with the aim of increasing their durability up to 20,000 hrs, are presented. To estimate the quality and properties of tube billet metal, microstructure, content and nature of nonmetallic inclusions, content of gases, austenite grain size, austenite transformations during continuous cooling, metal ductility, mechanical properties at different temperatures and heat resisting properties, have been investigated. It is established, that the base metal in tubes of electroslag remelting possess higher heat resistance, while welded joints besides, have high deformability and resistance to brittle fracture

Triosephosphate isomerase gene promoter variation: -5G/A and -8G/A polymorphisms in clinical malaria groups in two African populations.

Science.gov (United States)

Guerra, Mónica; Machado, Patrícia; Manco, Licínio; Fernandes, Natércia; Miranda, Juliana; Arez, Ana Paula

2015-06-01

TPI1 promoter polymorphisms occur in high prevalence in individuals from African origin. Malaria-patients from Angola and Mozambique were screened for the TPI1 gene promoter variants rs1800200A>G, (-5G>A), rs1800201G>A, (-8G>A), rs1800202T>G, (-24T>G), and for the intron 5 polymorphism rs2071069G>A, (2262G>A). -5G>A and -8G>A variants occur in 47% and 53% in Angola and Mozambique, respectively while -24T>G was monomorphic for the wild-type T allele. Six haplotypes were identified and -8A occurred in 45% of the individuals, especially associated with the GAG haplotype and more frequent in non-severe malaria groups, although not significantly. The arising and dispersion of -5G>A and -8G>A polymorphisms is controversial. Their age was estimated by analyses of two microsatellite loci, CD4 and ATN1, adjacent to TPI1 gene. The -5G>A is older than -8G>A, with an average estimate of approximately 35,000 years. The -8A variant arose in two different backgrounds, suggesting independent mutational events. The first, on the -5G background, may have occurred in East Africa around 20,800 years ago; the second, on the -5A background, may have occurred in West Africa some 7500 years ago. These estimates are within the period of spread of agriculture and the malaria mosquito vector in Africa, which could has been a possible reason for the selection of -8A polymorphism in malaria endemic countries. Copyright © 2015 Elsevier B.V. All rights reserved.

Gauged N=8 d=5 supergravity

International Nuclear Information System (INIS)

Pernici, M.; Pilch, K.; Van Nieuwenhuizen, P.

1985-01-01

The complete gauged nonlinear N=8 d=5 supergravity action and supersymmetry transformation laws (without four- and three-fermion terms) are presented. They are obtained from the ungauged model by reinterpreting part of the field strengths of the abelian vector fields as real self-dual second-rank antisymmetric tensors. The complete set of T-tensor indentities are given and their validity is checked numerically. The model has a local Yang-Mills SO(6) and a local composite USp(8) symmetry. The self-duality is essential for the consistent coupling of the antisymmetric tensors to the nonabelian gauge fields. (orig.)

The magnetic field of the equatorial magnetotail - AMPTE/CCE observations at R less than 8.8 earth radii

Science.gov (United States)

Fairfield, D. H.; Acuna, M. H.; Zanetti, L. J.; Potemra, T. A.

1987-01-01

The MPTE/CCE magnetic field experiment has been used to obtain a quantitative evaluation of the frequency and extent of magnetic field distortion in the near-tail region at less than 8.8 earth radii. The variation of this distortion with Kp, radial distance, longitude, and near-equatorial latitude is reported. It has been found that taillike distortions from the dipole field direction may reach 80 deg near the MPTE/CE apogee of 8.8 earth radii. The Bz field component in dipole coordinates was always positive within 0.5 earth radii of the equatorial current sheet, indicating the neutral lines were never seen inside of 8.8 earth radii. Fields were most taillike near midnight and during times of high Kp. At 8.5 earth radii the equatorial field magnitude depressions were roughly half the dipole field strength of 51 nT. These depressions are larger at lesser distances, reaching -40 nT at 3.4 earth radii for Kp of 2- or less and -80 nT and Kp of 3+ and greater.

Stainless austenitic steels strengthened due to reversible phase transformations and by ageing

International Nuclear Information System (INIS)

Sagaradze, V.V.; Kositsyna, I.I.; Ozhiganov, A.V.

1981-01-01

The effect of the reversible phase transformations, consisting in the conduction of the direct and reverse martensite transformations and aging, during which the intermetallide γ'-phase of the composition Ni 3 Ti is formed, on the streng-thening of alloys in the Fe-Cr-Ni-Ti system is considered. Stainless austenitic steels Kh12N12T3 and Kh12N14T3, which acquire high mechanical properties: σsub(0.2)=685-785 MPa, σsub(B)=1275 MPa, delta >= 20%, as a result of reversible phase transformations and aging, are suggested. After the reversible phase transformations and ageing the steels possess a high resistance to γ-α-transformation during cold treatment [ru

Mechanism of improvement on strength and toughness of H13 die steel by nitrogen

International Nuclear Information System (INIS)

Li, Jing-Yuan; Chen, Yu-Lai; Huo, Jian-Hua

2015-01-01

The mechanism of nitrogen addition to AISI H13 die steel is proposed and supported using thermodynamic calculations in addition to observed changes in precipitate, microstructure, crystal structure, and macroproperties. The results indicate that the average impact toughness ak of the novel nitrogen H13 steel is maximally 17.6 J cm −2 and minimally 13.4 J cm −2 . These values result in die steel that reaches premium grade and approximate the superior grade as specified in NADCA#207-2003, additionally the hardness is improved 3–5HRC. Experimental findings indicate that the residual V(C,N) particles undissolved during nitrogen H13 steel austenitizing by quenching helps to suppress growth of original austenitic crystal grains, this in turn results in finer martensitic structures after quenching. In the subsequent tempering process all N atoms are dissolved in the solid state matrix a result of C atoms displacing N atoms in V(C,N). Solid dissolution of N atoms produces a distorted lattice of Fe matrix which results in an increase in the hardness of the steel. Additionally this displacement reaction is important for slow growth of secondary particles in nitrogen H13 steel during the tempering process which helps to increase impact toughness compared to its nitrogen-free counterpart given the same condition of heat-treatment

40 CFR 8.8 - Comprehensive environmental evaluation.

Science.gov (United States)

2010-07-01

... conduct of scientific research and on other existing uses and values; (10) An identification of gaps in... evaluation. (a) Preparation of a CEE. Unless a PERM or an IEE has been submitted and determined to meet the... evaluate the CEE to determine if the CEE meets the requirements under Article 8 and Annex I to the Protocol...

Ultraviolet Behavior of N = 8 Supergravity

International Nuclear Information System (INIS)

Dixon, Lance J.

2010-01-01

In these lectures the author describes the remarkable ultraviolet behavior of N = 8 supergravity, which through four loops is no worse than that of N = 4 super-Yang-Mills theory (a finite theory). I also explain the computational tools that allow multi-loop amplitudes to be evaluated in this theory - the KLT relations and the unitarity method - and sketch how ultraviolet divergences are extracted from the amplitudes.

High prevalence of exon 8 G533C mutation in apparently sporadic medullary thyroid carcinoma in Greece.

Science.gov (United States)

Sarika, H L; Papathoma, A; Garofalaki, M; Vasileiou, V; Vlassopoulou, B; Anastasiou, E; Alevizaki, M

2012-12-01

Genetic screening for ret mutation has become routine practice in the evaluation of medullary thyroid carcinoma (MTC). Approximately 25% of these tumours are familial, and they occur as components of the multiple endocrine neoplasia type 2 syndromes (MEN 2A and 2B) or familial MTC. In familial cases, the majority of mutations are found in exons 10, 11, 13, 14 or 15 of the ret gene. A rare mutation involving exon 8 (G533C) has recently been reported in familial cases of MTC in Brazil and Greece; some of these cases were originally thought to be sporadic. The aim of this study was to re-evaluate a series of sporadic cases of MTC, with negative family history, and screen them for germline mutations in exon 8. Genomic DNA was extracted from peripheral lymphocytes in 129 unrelated individuals who had previously been characterized as 'sporadic' based on the negative family history and negative screening for ret gene mutations. Samples were analysed in Applied Biosystems 7500 real-time PCR and confirmed by sequencing. The G533C exon 8 mutation was identified in 10 of 129 patients with sporadic MTC. Asymptomatic gene carriers were subsequently identified in other family members. In our study, we found that 7·75% patients with apparently sporadic MTC do carry G533C mutation involving exon 8 of ret. We feel that there is now a need to include exon 8 mutation screening in all patients diagnosed as sporadic MTC, in Greece. © 2012 Blackwell Publishing Ltd.

AJESMS_ Vol 8 2010 August 15 2011

African Journals Online (AJOL)

Prof. Mereku

2010-08-15

Aug 15, 2010 ... mindedness among learners especially in the developing nations. Put differently, a typical ..... geometry (4), mean 40.8, reliability (KR-20) 0.89 and Standard Deviation 11.33. Method of Data ... Four figure tables. 7. (35%). 13.

El discurso hegemónico sobre las acciones colectivas de resistencia civil: Casos comunas 8, 9 y 13 de Medellín

OpenAIRE

Alzate Zuluaga, Mary Luz

2010-01-01

En este artículo se discute la manera cómo en la prensa escrita son informadas las distintas expresiones de resistencia civil, a partir del rastreo de la información registrada en la prensa escrita local y nacional acerca de los casos de las Comunas 8, 9 y 13 de la ciudad de Medellín durante los años 2002-2006. Se busca conocer así, de qué modo han sido descritas e interpretadas dichas prácticas, cuáles son las ausencias y los aspectos subrayados con lo emitido, qué relaciones de poder se leg...

Improving composition of protective coatings for steel casting

International Nuclear Information System (INIS)

Kuz'kina, N.N.; Pegov, V.G.; Bogatenkov, V.F.; Shub, L.G.; Raspopova, N.A.

1983-01-01

A radically new fuel-free slag-forming mixture used as protective coating for steel casting is introduced. The lack of combustible powders precludes explosion and fire Lazard in mixture preparation. Usage of the new mixture in stainless steel casting of Kh18N10T type permitted to improve the ingot surface quality and reduce spoilage from 1.16 to 0.66%

Imaging tumor endothelial marker 8 using an 18F-labeled peptide

International Nuclear Information System (INIS)

Quan, Qimeng; Yang, Min; Gao, Haokao; Zhu, Lei; Lin, Xin; Guo, Ning; Chen, Xiaoyuan; Zhang, Guixiang; Eden, Henry S.; Niu, Gang

2011-01-01

Tumor endothelial marker 8 (TEM8) has been reported to be upregulated in both tumor cells and tumor-associated endothelial cells in several cancer types. TEM8 antagonists and TEM8-targeted delivery of toxins have been developed as effective cancer therapeutics. The ability to image TEM8 expression would be of use in evaluating TEM8-targeted cancer therapy. A 13-meric peptide, KYNDRLPLYISNP (QQM), identified from the small loop in domain IV of protective antigen of anthrax toxin was evaluated for TEM8 binding and labeled with 18 F for small-animal PET imaging in both UM-SCC1 head-and-neck cancer and MDA-MB-435 melanoma models. A modified ELISA showed that QQM peptide bound specifically to the extracellular vWA domain of TEM8 with an IC 50 value of 304 nM. Coupling 4-nitrophenyl 2- 18 F-fluoropropionate with QQM gave almost quantitative yield and a high specific activity (79.2 ± 7.4 TBq/mmol, n = 5) of 18 F-FP-QQM at the end of synthesis. 18 F-FP-QQM showed predominantly renal clearance and had significantly higher accumulation in TEM8 high-expressing UM-SCC1 tumors (2.96 ± 0.84 %ID/g at 1 h after injection) than TEM8 low-expressing MDA-MB-435 tumors (1.38 ± 0.56 %ID/g at 1 h after injection). QQM peptide bound specifically to the extracellular domain of TEM8. 18 F-FP-QQM peptide tracer would be a promising lead compound for measuring TEM8 expression. Further efforts to improve the affinity and specificity of the tracer and to increase its metabolic stability are warranted. (orig.)

Investigation of precipitation and hardening response of maraging stainless steels 17-4 and 13-8+Mo during multi-pass welding

Science.gov (United States)

Hamlin, Robert J.

Martensitic precipitation strengthened stainless steels 17-4 and 13-8+Mo are candidate alloys for high strength military applications. These applications will require joining by fusion welding processes thus, it is necessary to develop an understanding of microstructural and mechanical property changes that occur during welding. Previous investigations on these materials have demonstrated that significant softening occurs in the heat affected zone (HAZ) during welding, due to dissolution of the strengthen precipitates. It was also observed that post weld heat treatments (PWHT's) were required to restore the properties. However, PWHT's are expensive and cannot be applied when welding on a large scale or making a repair in the field. Thus, the purpose of the current work is to gain a fundamental understanding of the precipitation kinetics in these systems so that optimized welding procedures can be developed that do not require a PWHT. Multi-pass welding provides an opportunity to restore the strengthening precipitates that dissolve during primary weld passes using the heat from secondary weld passes. Thus, a preliminary investigation was performed to determine whether the times and temperatures associated with welding thermal cycles were sufficient to restore the strength in these systems. A Gleeble thermo-mechanical simulator was used to perform multi-pass welding simulations on samples of each material using a 1000 J/mm and 2000 J/mm heat input. Additionally, base metal and weld metal samples were used as starting conditions to evaluate the difference in precipitation response between each. Hardness measurements were used to estimate the extent of precipitate dissolution and growth. Microstructures were characterized using light optical microscopy (LOM), scanning electron microscopy (SEM), and energy dispersive spectrometry (EDS). It was determined that precipitate dissolution occurred during primary welding thermal cycles and that significant hardening could be

40 CFR Table 8 to Subpart Xxxx of... - Initial Compliance With the Emission

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Initial Compliance With the Emission 8 Table 8 to Subpart XXXX of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED.... XXXX, Table 8 Table 8 to Subpart XXXX of Part 63—Initial Compliance With the Emission As stated in § 63...

Phylogenetic analysis of G1P[8] and G12P[8] rotavirus A samples obtained in the pre- and post-vaccine periods, and molecular modeling of VP4 and VP7 proteins.

Science.gov (United States)

Almeida, Tâmera Nunes Vieira; de Sousa, Teresinha Teixeira; da Silva, Roosevelt Alves; Fiaccadori, Fabíola Souza; Souza, Menira; Badr, Kareem Rady; de Paula Cardoso, Divina das Dôres

2017-09-01

Reduction in morbimortality rates for acute gastroenteritis (AGE) by Rotavirus A (RVA) has been observed after the introduction of vaccines, however the agent continues to circulate. The present study described the genomic characterization of the 11 dsRNA segments of two RVA samples G1P[8] obtained in the pre- and post-vaccination periods and one of G12P[8] sample (post-vaccine), compared to Rotarix™ vaccine. Analysis by molecular sequencing of the samples showed that the three samples belonged to genogroup I. In addition, the analysis of VP7 gene revealed that the samples G1 (pre-vaccine), G1 (post-vaccine) and G12 were characterized as lineages II, I and III, respectively. Regarding to VP4 and NSP4 gene it was observed that all samples belonged to lineage III, whereas for VP6 gene, the sample of the pre- and post-vaccine belonged to the lineage IV and I, respectively. Considering the VP7 gene, it was observed high nucleotide and amino acid identity for the two G1 samples when compared to Rotarix™ vaccine and lesser identity for the G12 sample. In relation to antigenic epitope of VP7 greater modifications were observed for the G12 sample in the 7-2 epitope that was confirmed by molecular modeling. On the other hand, for VP4, some changes in the 8-1 and 8-3 antigenic epitopes was observed for the three samples. This data could be interpreted as a low selective pressure exerted by vaccination in relation to G1P[8] samples and lesser protection in relation to G12P[8]. Thus, the continuous monitoring of RVA circulating samples remains important. Copyright © 2017 Elsevier B.V. All rights reserved.

Adams-Iwasawa N=8 Black Holes

CERN Document Server

Cacciatori, Sergio Luigi; Marrani, Alessio

2012-01-01

We study some of the properties of the geometry of the exceptional Lie group E7(7), which describes the U-duality of the N=8, d=4 supergravity. In particular, based on a symplectic construction of the Lie algebra e7(7) due to Adams, we compute the Iwasawa decomposition of the symmetric space M=E7(7)/(SU(8)/Z_2), which gives the vector multiplets' scalar manifold of the corresponding supergravity theory. The explicit expression of the Lie algebra is then used to analyze the origin of M as scalar configuration of the "large" 1/8-BPS extremal black hole attractors. In this framework it turns out that the U(1) symmetry spanning such attractors is broken down to a discrete subgroup Z_4, spoiling their dyonic nature near the origin of the scalar manifold. This is a consequence of the fact that the maximal manifest off-shell symmetry of the Iwasawa parametrization is determined by a completely non-compact Cartan subalgebra of the maximal subgroup SL(8,R) of E7(7), which breaks down the maximal possible covariance SL...

Topic 1. Steels for light water reactor pressure vessels

International Nuclear Information System (INIS)

Brumovsky, M.; Brynda, J.; Kepka, M.; Barackova, L.; Vacek, M.; Havel, S.; Cukr, B.; Protiva, K.; Petrman, I.; Tvrdy, M.; Hyspecka, L.; Mazanec, K.; Kupca, L.; Brezina, M.

1980-01-01

Part 1 of the Proceedings consists of papers on the criteria for the selection and comparison of the properties of steel for pressure vessels and on the metallurgy of the said steels, the selection of suitable material for internal tubing systems, the manufacture of high-alloy steels for WWER components, the mechanical and metallurgical properties of steel 22K for WWER 440 pressure components, and of steel 10MnNi2Mo for the WWER primary coolant circuit, and the metallographic assessment of steel 0Kh18N10T. (J.P.)

Microstructure and Mechanical Properties of Laser Clad and Post-cladding Tempered AISI H13 Tool Steel

Science.gov (United States)

Telasang, Gururaj; Dutta Majumdar, Jyotsna; Wasekar, Nitin; Padmanabham, G.; Manna, Indranil

2015-05-01

This study reports a detailed investigation of the microstructure and mechanical properties (wear resistance and tensile strength) of hardened and tempered AISI H13 tool steel substrate following laser cladding with AISI H13 tool steel powder in as-clad and after post-cladding conventional bulk isothermal tempering [at 823 K (550 °C) for 2 hours] heat treatment. Laser cladding was carried out on AISI H13 tool steel substrate using a 6 kW continuous wave diode laser coupled with fiber delivering an energy density of 133 J/mm2 and equipped with a co-axial powder feeding nozzle capable of feeding powder at the rate of 13.3 × 10-3 g/mm2. Laser clad zone comprises martensite, retained austenite, and carbides, and measures an average hardness of 600 to 650 VHN. Subsequent isothermal tempering converted the microstructure into one with tempered martensite and uniform dispersion of carbides with a hardness of 550 to 650 VHN. Interestingly, laser cladding introduced residual compressive stress of 670 ± 15 MPa, which reduces to 580 ± 20 MPa following isothermal tempering. Micro-tensile testing with specimens machined from the clad zone across or transverse to cladding direction showed high strength but failure in brittle mode. On the other hand, similar testing with samples sectioned from the clad zone parallel or longitudinal to the direction of laser cladding prior to and after post-cladding tempering recorded lower strength but ductile failure with 4.7 and 8 pct elongation, respectively. Wear resistance of the laser surface clad and post-cladding tempered samples (evaluated by fretting wear testing) registered superior performance as compared to that of conventional hardened and tempered AISI H13 tool steel.

Astrophysical S factor for the 7Li(d,n0)8Be and 7Li(d,n1)8Be reactions

International Nuclear Information System (INIS)

Sabourov, A.; Ahmed, M.W.; Blackston, M.A.; Crowell, A.S.; Howell, C.R.; Perdue, B.A.; Sabourov, K.; Tonchev, A.; Weller, H.R.; Prior, R.M.; Spraker, M.C.

2006-01-01

The absolute astrophysical S factor and cross section for the 7 Li(d,n 0 ) 8 Be and 7 Li(d,n 1 ) 8 Be reactions have been determined using deuteron beams with energies between 45 and 80 keV. The slope of the S factor is consistent with zero in the n 0 case but is slightly negative in the n 1 case. The S factor for the sum of both neutron groups at c.m. energies below 70 keV is S(E)=5400(±1500)-37(±21)E keV b, where E is the c.m. energy in keV

Synthesis of R-(+)- and S-(-)-8-hydroxy-2-(N,N-dipropylamino)-2[2-3H]tetralin. HCl (8-OH-DPAT) a 5HT1A receptor agonist

International Nuclear Information System (INIS)

Ackland, M.J.; Dring, L.G.; Jones, J.R.

1991-01-01

The title compounds were synthesised in 7 steps from 1,7-dihydroxynaphthalene as follows: 1,7-dihydroxynaphthalene was methylated and subjected to a Birch reduction to yield 8-methoxy-2-tetralone. Reductive amination with sodium cyanoboro[ 3 H]hydride and n-propylamine gave 8-methoxy-2-(n-propylamino)-[2- 3 H]tetralin which was acylated and reduced to give (±)8-methoxy-2-(N,N-dipropylamino)-[2 3 H]tetralin. Treatment with conc.HC1 gave (±)-8-hydroxy-2-(N,N-dipropylamino)-[2- 3 H]tetralin. The racemate was then resolved by chiral mobile phase chromatography. (author)

Fouling and biocorrosion of a high-alloy steel in the Golden Horn bay

International Nuclear Information System (INIS)

Koryakova, M.D.; Nikitin, V.M.; Suponina, A.P.; Kharchenko, U.V.; Zvyagintsev, A.Yu.

2002-01-01

The studies on the effect of contamination of the Golden Horn bay waters (the Peter the Great Bay in the Japanese Sea) on formation of the community of the bacterio- and macrofouling and corrosion resistance of the Kh18N10T high-alloy steel are continued. The dissolved and chemically absorbed oxygen, pH, saprophytes, oil-oxidizing, sulfate-reducing bacteria and heavy metals are among the medium indicators, characterizing the level of pollution of the regions of the samples testing. It is shown, that the obtained experimental data extend our understanding of the dependent effect of three factors: the sea medium → fouling → corrosion resistance of the Kh18N10T high-alloy steel [ru

Creep and rupture behavior of weld-deposited Type 16-8-2 stainless steel at 5930C

International Nuclear Information System (INIS)

Ward, A.L.; Blackburn, L.D.

1976-03-01

The creep and rupture behavior of weld-deposited Type 16-8-2 stainless steel at 593 0 C was investigated over the time range from 3.6 x 10 4 s to 2.5 x 10 7 s. Equations relating stress to the time to rupture, the time to the onset of tertiary creep, and the time to produce a given creep strain were obtained. The experimental results indicate that the control of welding parameters (e.g. current, voltage and travel speed) within reasonable ranges can yield weld deposits with consistent time-dependent properties. Limited data suggest that high temperature (1065 0 C) post-weld annealing significantly alters only the flow curve for plastic deformation, while long-term thermal exposure at an intermediate temperature (565 0 C) produces only minor changes in either the plastic deformation or creep behavior of the weld materials

Properties of cast CF-8 stainless-steel weldments at cryogenic temperatures

International Nuclear Information System (INIS)

Chow, J.G.Y.; Klamut, C.J.

1981-01-01

ISABELLE is a 400 x 400 GeV proton-proton colliding beam accelerator now under construction at Brookhaven National Laboratory. The beams will be guided and focused by superconducting magnets. A total of 722 dipole beam bending magnets and 280 quadrupole beam focusing magnets are required. Centrifugally cast CF-8 stainless steel tubes were selected to provide a rigid support and to house the superconducting magnet assembly. The selection of this material for the support tubes is discussed by Dew-Hughes and Lee. Their study indicates that the presence of delta ferrite strengthens the material but causes a decrease in ductility if the ferrite content is greater than 10%. Brown and Tobler found that the fracture toughness is also decreased as the delta ferrite content is increased

8×8 Planar Phased Array Antenna with High Efficiency and Insensitivity Properties for 5G Mobile Base Stations

DEFF Research Database (Denmark)

Ojaroudiparchin, Naser; Shen, Ming; Pedersen, Gert F.

2016-01-01

An insensitive planar phased array antenna with high efficiency function for 5G applications is introduced in this study. 64-elements of compact slot-loop antenna elements have been used to form the 8×8 planar array. The antenna is designed on a low cost FR4 substrate and has good performance in ...... at both sides of the substrate and could be used for mobile base station (MBS) applications. The proposed planar array could be integrated with the transceivers on the low-cost printed circuit boards (PCBs) to reduce the manufacturing cost....

Effects of Manganese Content on Solidification Structures, Thermal Properties, and Phase Transformation Characteristics in Fe-Mn-Al-C Steels

Science.gov (United States)

Yang, Jian; Wang, Yu-Nan; Ruan, Xiao-Ming; Wang, Rui-Zhi; Zhu, Kai; Fan, Zheng-Jie; Wang, Ying-Chun; Li, Cheng-Bin; Jiang, Xiao-Fang

2015-04-01

To assist developments of the continuous-casting technology of Fe-Mn-Al-C steels, the solidification structures and the thermal properties of Fe-Mn-Al-C steel ingots with different manganese contents have been investigated and the phase transformation characteristics have been revealed by FactSage (CRCT-ThermFact Inc., Montréal, Canada). The results show that the thermal conductivity of the 0Mn steel is the highest, whereas the thermal conductivity of the 8Mn steel is slightly higher than that of the 17Mn steel. Increasing the manganese content promotes a columnar solidification structure and coarse grains in steel. With the increase of manganese content, the mass fraction of austenite phase is increased. Finally, a single austenite phase is formed in the 17Mn steel. The mean thermal expansion coefficients of the steels are in the range from 1.3 × 10-5 to 2.3 × 10-5 K-1, and these values increase with the increase of manganese content. The ductility of the 17Mn steel and the 8Mn steel are higher than 40 pct in the temperature range from 873 K to 1473 K (600 °C to 1200 °C), and the cracking during the straightening operation should be avoided. However, the ductility of the 0Mn steel is lower than 40 pct at 973 K and 1123 K (700 °C and 850 °C), which indicates that the temperature of the straightening operation during the continuous-casting process should be above 1173 K (900 °C). Manganese has the effect of enlarging the austenite phase region and reducing the δ-ferrite phase region and α-ferrite phase region. At the 2.1 mass pct aluminum level, the precipitate temperature of AlN is high. Thus, the formed AlN is too coarse to deteriorate the hot ductility of steel.

Molecular cytogenetic characterization of mosaicism for a small supernumerary marker chromosome derived from chromosome 8 or r(8(::p12→q13.1:: associated with phenotypic abnormalities

Directory of Open Access Journals (Sweden)

Chih-Ping Chen

2016-12-01

Conclusion: Mosaic sSMC(8 derived from r(8(::p12→q13.1:: can present phenotypic abnormalities. Chromosome 8q12 duplication syndrome should be included in differential diagnosis when an sSMC(8 contains 8q12.2 and CHD7.

Towards a worldsheet description of N=8 supergravity

International Nuclear Information System (INIS)

Lipstein, Arthur; Schomerus, Volker

2015-10-01

In this note we address the worldsheet description of 4-dimensional N=8 supergravity using ambitwistors. After gauging an appropriate current algebra, we argue that the only physical vertex operators correspond to the N=8 supermultiplet. It has previously been shown that worldsheet correlators give rise to supergravity tree level scattering amplitudes. We extend this work by proposing a definition for genus-one amplitudes that passes several consistency checks such as exhibiting modular invariance and reproducing the expected infrared behavior of 1-loop supergravity amplitudes.

[2,3,7,8,13,14,17,18-Octa?kis(ethyl?sulfan?yl)-5,10,15,20-porphyrazinato]zinc(II)

OpenAIRE

Akkurt, Mehmet; Co?kun, Naciye Y?lmaz; K?l??aslan, Fatma Aytan; Yal??n, Sabiha Manav; B?y?kg?ng?r, Orhan; G?l, Ahmet

2010-01-01

In the title compound, [Zn(C32H40N8S8)], the ZnII ion is coordinated by four N atoms in a slightly distorted square-planar environment. In addition, there is a Zn...S contact involving a symmetry-related S atom which, when considered, forms a pseudo-square-pyramidal coordination with respect to the ZnII ion. Three of the ethyl groups are disordered over two sites with occupancy ratios of 0.841 (10):0.159 (10), 0.802 (10):0.198 (10) and 0.457 (...

Study of isotope effects in the hydrogen transport of an 8% CrWVTa martensitic steel

International Nuclear Information System (INIS)

Esteban, G.A.; Sedano, L.A.; Perujo, A.; Douglas, K.

2001-01-01

A time-dependent gas-phase isovolumetric desorption technique has been used to assess the isotope effects in the diffusive transport parameters of hydrogen in an 8% CrWVTa reduced activation martensitic steel in the temperature range of 423-892 K and driving pressures from 4 x 10 4 - 1 x 10 5 Pa. The experiments have been run with both protium and deuterium obtaining their respective transport parameters, diffusivity (D), Sieverts' constant (K S ), permeability (Φ), trap site density (η t ) and the trapping activation energy (E t ). Isotope effects on steel are analysed and compared with α-iron. A new way to derive more accurate tritium transport parameters is proposed. (orig.)

Effect of neutron irradiation on the properties of the repair welds of the 15Kh2MFA steel

International Nuclear Information System (INIS)

Morozov, A.M.; Khachaturyants, L.V.

1986-01-01

The authors studied the effect of neutron irradiation on the tendency of the metal belonging to the heat affected zone of the weld toward brittle fracture (an increase in the critical temperature of brittleness). For comparison, the authors studied the radiation embrittlement of the original base metal (steel 15Kh2MFA) subjected to the conventional heat treatment of the reactor frames consisting of hardening and high-temperature tempering. Along with these materials, the radiational embrittlement of the base metal in the rehardened condition without tempering was studied. It was concluded that the presence of the regions repaired according to this technology and located in the frame at the level of the reactor core does not pose the problem of decreased resistance to brittle fracture

Genetic linkage maps of chicken chromosomes 6, 7, 8, 11 and 13 from a Brazilian resource population Mapas de ligação dos cromossomos 6, 7, 8, 11 e 13 de uma população brasileira de galinha

Directory of Open Access Journals (Sweden)

Marcel Ambo

2008-01-01

de duas gerações de cruzamentos entre uma linhagem de corte e uma de postura. Foram testados 51 marcadores microssatélites, dos quais 28 foram informativos: 4, 8, 7, 4 e 5 dos cromossomos 6, 7, 8, 11 e 13, respectivamente. Um SNP localizado no gene do receptor da leptina foi incluído no cromossomo 8. Os 10 parentais, 8 F1 e um total de 459 aves F2 de cinco famílias de irmãos completos foram genotipados com estes marcadores. O número de meioses informativas totais por loco variou de 232 a 862 e o de meioses informativas de fase conhecida de 0 a 764. A ordem dos marcadores nos cromossomos coincidiu com a do mapa consenso da galinha, com exceção dos marcadores ADL0147 e MCW0213 do cromossomo 13 que tiveram sua ordem invertida. O número reduzido de meioses informativas de fase conhecida para o marcador ADL0147 (150 pode ser apontado como uma possível causa para a inversão, além da relativa proximidade entre os dois marcadores envolvidos na inversão (10,5 cM.

8-13 μm spectra of very late type Wolf-Rayet stars

International Nuclear Information System (INIS)

Aitken, D.K.; Barlow, M.J.; Roche, P.F.; Spenser, P.M.

1980-01-01

8 to 13 μm spectra are presented of the late Wolf-Rayet stars, Ve 2-45 (WC9), CRL 2104 (WC8), He 2-113 (WC10) and CPD-56 0 8032 (WC10). Both WC10 stars show the unidentified feature at 11.25 μm and one of them that at 8.6 μm; their spectra resemble those of some planetary nebulae. These features are absent in the WC8/9 stars, whose spectra, together with their infrared photometric data, can be understood in terms of approximately 900 K blackbody spectra subject to some interstellar silicate absorption and with a small excess beyond 10 μm, perhaps due to SiC grains. The WC10 objects are characterized by much lower dust temperatures and their evolutionary status appears to be very different from that of the WC8/9 stars. (author)

Measurements of the {sup 40}Ar(n, γ){sup 41}Ar radiative-capture cross section between 0.4 and 14.8 MeV