Technological start of T-15 tokamak. The start-up diagnostic complex

International Nuclear Information System (INIS)

Notkin, G.E.

1989-01-01

The T-15 tokamak with superconducting toroidal winding reached the technological start-up phase. The results of the first operating tests of the main tokamak components are reported. Due to improper function of both the vacuum and the cryogenic system, the nominal parameters of the vacuum and of the toroidal magnetic field have not been achieved. The non-optimum vacuum conditions made the discharge start-up difficult even when a pre-ionizing electron beam and a gyrotron generator were used. The pre-discharge plasma parametes were studied by means of a limited set of plasma diagnostic apparatus. Due to substantially deteriorated vacuum conditions, it was not possible to repeat the only one successful discharge with a current of 100 kA, lasting for 50 ms. (J.U.)

High Time Resolution Measurements of VOCs from Vehicle Cold Starts: The Air Toxic Cold Start Pulse

Science.gov (United States)

Jobson, B. T.; Huangfu, Y.; Vanderschelden, G. S.

2017-12-01

Pollutants emitted during motor vehicle cold starts, especially in winter in some climates, is a significant source of winter time air pollution. While data exist for CO, NO, and total hydrocarbon emissions from federal testing procedures for vehicle emission certification, little is known about the emission rates of individual volatile organic compounds, in particular the air toxics benzene, formaldehyde, and acetaldehyde. Little is known about the VOC speciation and temperature dependence for cold starts. The US EPA vehicle emission model MOVES assumes that cold start emissions have the same speciation profile as running emissions. We examined this assumption by measuring cold start exhaust composition for 4 vehicles fueled with E10 gasoline over a temperature range of -4°C to 10°C in winter of 2015. The extra cold start emissions were determined by comparison with emissions during engine idling. In addition to CO and NOx measurements a proton transfer reaction mass spectrometer was used to measure formaldehyde, acetaldehyde, benzene, toluene, and C2-alkylbenzenes at high time resolution to compare with the cold start emission speciation profiles used in the EPA MOVES2014 model. The results show that after the vehicle was started, CO mixing ratios can reach a few percent of the exhaust and then drop to several ppmv within 2 minutes of idling, while NOx showed different temporal behaviors among the four vehicles. VOCs displayed elevated levels during cold start and the peak mixing ratios can be two orders higher than idling phase levels. Molar emission ratios relative to toluene were used to compare with the emission ratio used in MOVES2014 and we found the formaldehyde-to-toluene emission ratio was about 0.19, which is 5 times higher than the emission ratio used in MOVES2014 and the acetaldehyde-to-toluene emission ratios were 0.86-0.89, which is 8 times higher than the ones in MOVES2014. The C2-alkylbenzene-to-toluene ratio agreed well with moves. Our results

Start 2: Thinking one move ahead

Energy Technology Data Exchange (ETDEWEB)

Gaines, L.L.

1991-11-01

At their summit meeting in the spring of 1990, Presidents Bush and Gorbachev issued a joint statement expressing their intentions to continue the process of strategic arms control beyond the Strategic Arms Reduction Treaty (START), which was eventually signed in July 1991, toward agreement on further reductions. They set general goals for negotiation of a follow-on treaty to START, which has been called START II. President Bush`s historic speech on September 27, 1991, reinforced those goals and specified several actions the US would take. It is the purpose of this report to examine possible provisions of START II and the implications of those provisions for achievement of the goals set at the 1990 summit, for verifiability, and for US force planning. This look ahead will contribute to advance planning of appropriate negotiating positions, verification research and development (R&D), and force modernization and restructuring. This report describes the goals for a START II treaty and possible means for achieving them. It postulates one set of provisions for such a treaty, while it examines force structures for the US that could result from adoption of a treaty with these provisions. The adequacy of methods for verifying START II are examined and the implications of a START II treaty are postulated.

Start 2: Thinking one move ahead

Energy Technology Data Exchange (ETDEWEB)

Gaines, L.L.

1991-11-01

At their summit meeting in the spring of 1990, Presidents Bush and Gorbachev issued a joint statement expressing their intentions to continue the process of strategic arms control beyond the Strategic Arms Reduction Treaty (START), which was eventually signed in July 1991, toward agreement on further reductions. They set general goals for negotiation of a follow-on treaty to START, which has been called START II. President Bush's historic speech on September 27, 1991, reinforced those goals and specified several actions the US would take. It is the purpose of this report to examine possible provisions of START II and the implications of those provisions for achievement of the goals set at the 1990 summit, for verifiability, and for US force planning. This look ahead will contribute to advance planning of appropriate negotiating positions, verification research and development (R D), and force modernization and restructuring. This report describes the goals for a START II treaty and possible means for achieving them. It postulates one set of provisions for such a treaty, while it examines force structures for the US that could result from adoption of a treaty with these provisions. The adequacy of methods for verifying START II are examined and the implications of a START II treaty are postulated.

Lean start-up

DEFF Research Database (Denmark)

Rasmussen, Erik Stavnsager; Tanev, Stoyan

2016-01-01

The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The ma...... and the final business model. In other words: The start-up must first nail the problem together with the customers, then develop the solution and test, and then in the end scale it to a full-grown business model.......The risk of launching new products and starting new firms is known to be extremely high. The Lean Start-up approach is a way of reducing these risks and enhancing the chances for success by validating the products and services in the market with customers before launching it in full scale. The main...

Key parameters of the swimming start and their relationship to start performance.

Science.gov (United States)

Tor, Elaine; Pease, David L; Ball, Kevin A

2015-01-01

The swimming start is typically broken into three sub-phases; on-block, flight, and underwater phases. While overall start performance is highly important to elite swimming, the contribution of each phase and important technical components within each phase, particularly with the new kick-start technique, has not been established. The aim of this study was to identify technical factors associated with overall start performance, with a particular focus on the underwater phase. A number of parameters were calculated from 52 starts performed by elite freestyle and butterfly swimmers. These parameters were split into above-water and underwater groupings, before factor analysis was used to reduce parameter numbers for multiple regression. For the above-water phases, 81% of variance in start performance was accounted for by take-off horizontal velocity. For the underwater water phase, 96% of variance was accounted for with time underwater in descent, time underwater in ascent and time to 10 m. Therefore, developing greater take-off horizontal velocity and focussing on the underwater phase by finding the ideal trajectory will lead to improved start performance.

From START to NEW START. The dilemma and future of nuclear disarmament; Von START zu NEW START. Das Dilemma und die Zukunft der Nuklearen Abruestung

Energy Technology Data Exchange (ETDEWEB)

Plettenberg, Lars

2012-07-01

The report describes the existing four agreements on nuclear disarmament: START I (1991). START II (1993), SORT (2002) and NEW START (2010). The chapter on the dependence between nuclear disarmament and strategic stability covers the issues mutual assured destruction (MAD), credibility, overkill capacity; the role of nuclear weapons in the national strategies of the USA and NATO, Russia, Great Britain, France, China and the other nuclear states. Ways out of MAD include disarmament, de-alerting and mutual assured protection (MAP).

Smart or Diverse Start-up Teams?

DEFF Research Database (Denmark)

Hoogendoorn, Sander; Parker, Simon C.; Van Praag, Mirjam

2017-01-01

This paper explores the relationship between cognitive abilities and team performance in a start-up setting. We argue that performance in this setting hinges on three tasks: opportunity recognition, problem solving, and implementation. We theorize that cognitive ability at the individual level has...... others can be assigned to tasks that impose a greater cognitive load (problem solving or opportunity recognition). We present the results of a field experiment in which 573 students in 49 teams started up and managed real companies. We ensured exogenous variation in—otherwise random—team composition...... by assigning students to teams based on their measured cognitive abilities. Each team performed a variety of tasks, often involving complex decision making. The key result of the experiment is that the performance of start-up teams first increases and then decreases with ability dispersion. Strikingly, average...

Cold starting characteristics analysis of hydraulic free piston engine

International Nuclear Information System (INIS)

Zhang, Shuanlu; Zhao, Zhenfeng; Zhao, Changlu; Zhang, Fujun; Wang, Shan

2017-01-01

The cold start characteristic of hydraulic free piston diesel engine may affect its stable operation. Therefore the specific cold start characteristics, such as BDC or TDC positions, pressure in-cylinder, heat release rate, should be investigated in detail. These parameters fluctuate in some regularity in the cod start process. With the development of the free piston engine prototype and the establishment of test bench, the results are obtained. For the dynamic results, the fluctuation range of TDC and BDC positions is 8 mm and decreases with time. The thermodynamic results show that the combustion process is not stable and the pressure in-cylinder fluctuates largely in the cold start process. In addition, the combustion is rapid and knock happens inevitably. In order to investigate the reasons, a CFD model is established for temperature analysis in-cylinder and heat transfer conditions. It is found that higher start wall temperature will lead to more uniform temperature distribution. The delay period may decreases and heat release will move forward. This reason is analyzed by thermodynamic derivation based on the first law of thermodynamics. Finally, the improvement suggestions of cold start strategy are proposed. - Highlights: • The cold start behaviors of HFPE are investigated in detail. • CFD method is used for simulating temperature distribution in start process. • Thermodynamic derivation uncovers the compression temperature distribution. • The improvement suggestions of cold start strategy are proposed.

Research nuclear reactor start-up simulator

International Nuclear Information System (INIS)

Sofo Haro, M.; Cantero, P.

2009-01-01

This work presents the design and FPGA implementation of a research nuclear reactor start-up simulator. Its aim is to generate a set of signals that allow replacing the neutron detector for stimulated signals, to feed the measurement electronic of the start-up channels, to check its operation, together with the start-up security logic. The simulator presented can be configured on three independent channels and adjust the shape of the output pulses. Furthermore, each channel can be configured in 'rate' mode, where you can specify the growth rate of the pulse frequency in %/s. Result and details of the implementation on FPGA of the different functional blocks are given. (author)

Start-up emissions from residential down-draught wood log boilers

Energy Technology Data Exchange (ETDEWEB)

Pettersson, E. (Luleaa Univ. of Technology (Sweden). Energy Technology Centre in Piteaa), Email: esbjorn.pettersson@ltu.se

2009-07-01

Start-up emissions can be substantial and even dominating in real use. There are few published investigations regarding the relative importance of different parameters on the start-up emissions. It has though recently been stated that for down-draught boilers, best results are achieved if the wood charge is ignited fairly close to the secondary chamber. The objective of the experimental work was to evaluate the effect of different fuel and design parameters on the start-up emissions, using experimental design which enables a direct comparison between different parameters, using three levels of preheating of secondary air, electric preheating of primary air, different moisture and size of the start wood as well as different amounts of birch bark, which was used to spread the fire during the start. The boiler did not use a bypass damper and the full fuel charge was added before igniting the start wood through an ignition door situated slightly above the grate. The only significant results for the four parameters were that smaller and drier start wood gave lower start-up emissions. Extra amount of birch bark gave the same result. The most important parameters are the fuel parameters, which mean that the result is generally applicable. (orig.)

FY 1992 Research and development project for industrial science and technology. Part 1/2. Report on results of the R and D project for atomic/molecular level extreme manipulation technologies; 1992 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. 1/2

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-09-01

Described herein are the FY 1992 results of the survey, research and development project aimed at establishment of the technologies for observing/manipulating atoms and molecules as the common basic technologies for various industrial areas, e.g., new materials, electronics, biotechnology and chemistry. The R and D program for the technologies for observing/manipulating atoms/molecules on solid surfaces involve studies on possibility of surface process controlling aided by, e.g., various mechanical probing techniques and electron beams, and on device structures and analytical procedures for measurement/analysis of the dynamic steps of atomic/molecular processes, producing the basic findings. Observation of hydrogen atoms adsorbed on Si surfaces is started anew, using a newly introduced superhigh-precision surface analysis/controlling device. Knowledge is obtained for research and development of the technologies for observing/manipulating a group of atoms within a space, observing/manipulating structures of organic compounds or the like, and atomic/molecular process theories , among others, through surveys of overseas situations, invitation of researchers, international workshops, technological information exchanges, etc. (NEDO)

A Fast-Starting Robotic Fish

Science.gov (United States)

Modarres-Sadeghi, Yahya; Watts, Matthew; Conte, Joe; Hover, Franz; Triantafyllou, Michael

2009-11-01

We have built a simple mechanical system to emulate the fast-start performance of fish. The system consisted of a thin metal beam covered by a urethane rubber fish body. The body form of the mechanical fish in this work was modeled from a pike species, which is the most successfully studied fast-start specialist species. The mechanical fish was held in curvature and hung in water by two restraining lines, which were simultaneously released by pneumatic cutting mechanisms. The potential energy in the beam was transferred into the fluid, thereby accelerating the fish, similar to a pike. We measured the resulting velocity and acceleration, as well as the efficiency of propulsion for the mechanical fish model and also ran a series of flow visualization tests to observe the resulting flow pattern. We also studied the influence of stiffness and geometry of the tail on the efficiency of propulsion and flow pattern. The hydrodynamic efficiency of the fish, calculated by the transfer of energy, was around 10%. Flow visualization of the mechanical fast-start wake was also analyzed, showing that the acceleration is associated with the fast movement of an intense vortex in a near-lateral direction.

Later Start, Longer Sleep: Implications of Middle School Start Times

Science.gov (United States)

Temkin, Deborah A.; Princiotta, Daniel; Ryberg, Renee; Lewin, Daniel S.

2018-01-01

Background: Although adolescents generally get less than the recommended 9 hours of sleep per night, research and effort to delay school start times have generally focused on high schools. This study assesses the relation between school start times and sleep in middle school students while accounting for potentially confounding demographic…

Dampak Mentoring Pada Keberhasilan Start-Up Business: Studi Kasus Pada Start-Up Business di Indonesia [Mentoring the Impact of Success of a Start-Up Business: A Case Study of a Start-Up Business in Indonesia

Directory of Open Access Journals (Sweden)

Christina Yanita Setyawati

2016-10-01

Full Text Available Entrepreneurship is a highly developed science today, as well as in the world of education in Indonesia. Teaching entrepreneurship at the university level, especially at some universities in Surabaya, the second largest city in Indonesia, shows the positive impact that there were 74.03% of start-up businesses that survived and thrived in 2014. Based on the previous observation, some business start-ups are accompanied by a mentor. Mentoring is a process of forming and maintaining lasting relationships that develop intensively among seniors with juniors. The mentoring function includes career and psychosocial functions. The main purpose of this research is to study the relationship between mentoring and the success of a start-up business. This study is a quantitative descriptive study using a random sampling method to obtain 100 samples. The tool used to collect data was a questionnaire. The methodology used to analyze the quantitative description to test the hypothesis. The results of this study indicate that mentoring influences the success of a start-up business that was owned by university students in Surabaya, Indonesia by 32% and 78% was influenced by other variables.

How to Start Growing Beef Calves on Feed

OpenAIRE

ZoBell, Dale R

2003-01-01

Starting calves on feed takes time and effort because of the stress young calves are susceptible to at this point in their lives. The reduction of stress will result in calves consuming more feed, thus remaining healthier. To successfully start calves on feed, dry matter intake must be maximized while minimizing health problems. The following is a 5-step applied method for starting calves on a silage-based ration.

Start-up Funding via Equity Crowdfunding in Germany

DEFF Research Database (Denmark)

Angerer, Martin; Brem, Alexander; Kraus, Sascha

2017-01-01

Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types of crowdfund......Entrepreneurs often struggle to find sufficient funding for their start-ups. A relatively new way for companies to attract capital is via an internet platform, locating investors who in return receive something in return for their ventures. Equity crowdfunding is one of several types...... of crowdfunding, and is also known as crowdinvesting in the German-speaking realm. This article predominantly advances the scientific knowledge regarding the success factors of equity crowdfunding for German start-ups. The study conducted nine qualitative interviews with start-ups and crowdinvesting platforms....... Its first result is that German start-ups select crowdinvesting because (1) it is a funding opportunity and (2) it has an expected marketing effect. To organize the results of relevant success factors, the Crowdinvesting Success Model was designed by the researchers. This supports German entrepreneurs...

Classification Method to Define Synchronization Capability Limits of Line-Start Permanent-Magnet Motor Using Mesh-Based Magnetic Equivalent Circuit Computation Results

Directory of Open Access Journals (Sweden)

Bart Wymeersch

2018-04-01

Full Text Available Line start permanent magnet synchronous motors (LS-PMSM are energy-efficient synchronous motors that can start asynchronously due to a squirrel cage in the rotor. The drawback, however, with this motor type is the chance of failure to synchronize after start-up. To identify the problem, and the stable operation limits, the synchronization at various parameter combinations is investigated. For accurate knowledge of the operation limits to assure synchronization with the utility grid, an accurate classification of parameter combinations is needed. As for this, many simulations have to be executed, a rapid evaluation method is indispensable. To simulate the dynamic behavior in the time domain, several modeling methods exist. In this paper, a discussion is held with respect to different modeling methods. In order to include spatial factors and magnetic nonlinearities, on the one hand, and to restrict the computation time on the other hand, a magnetic equivalent circuit (MEC modeling method is developed. In order to accelerate numerical convergence, a mesh-based analysis method is applied. The novelty in this paper is the implementation of support vector machine (SVM to classify the results of simulations at various parameter combinations into successful or unsuccessful synchronization, in order to define the synchronization capability limits. It is explained how these techniques can benefit the simulation time and the evaluation process. The results of the MEC modeling correspond to those obtained with finite element analysis (FEA, despite the reduced computation time. In addition, simulation results obtained with MEC modeling are experimentally validated.

Nationwide Standards Eyed Anew

Science.gov (United States)

Olson, Lynn

2005-01-01

With the federal No Child Left Behind Act underscoring the wide variation in what states demand of their students, people on both sides of the political aisle are again making the case for national standards, curricula, and tests. It wasn't so long ago--during the Clinton and George H.W. Bush administrations--that similar proposals went down in…

A New Poetry Anew.

Science.gov (United States)

Grumman, Bob

1994-01-01

Classifies the various forms that exist in a type of poetry dubbed "burstnorm" poetry, a form of lyrical poetry. Differentiates burstnorm from two other types, "plaintext" and "songmode poetry." Describes three types of burstnorm poetry: surrealistic, pluraesthetic, and language poetry. Discusses further subtypes of…

Dynamic usage of transcription start sites within core promoters

DEFF Research Database (Denmark)

Kawaji, Hideya; Frith, Martin C; Katayama, Shintaro

2006-01-01

BACKGROUND: Mammalian promoters do not initiate transcription at single, well defined base pairs, but rather at multiple, alternative start sites spread across a region. We previously characterized the static structures of transcription start site usage within promoters at the base pair level......, based on large-scale sequencing of transcript 5' ends. RESULTS: In the present study we begin to explore the internal dynamics of mammalian promoters, and demonstrate that start site selection within many mouse core promoters varies among tissues. We also show that this dynamic usage of start sites...... is associated with CpG islands, broad and multimodal promoter structures, and imprinting. CONCLUSION: Our results reveal a new level of biologic complexity within promoters--fine-scale regulation of transcription starting events at the base pair level. These events are likely to be related to epigenetic...

76 FR 37174 - Capital Investment Program-New Starts and Small Starts Program Funds

Science.gov (United States)

2011-06-24

... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Capital Investment Program--New Starts... apportionment of the FY 2011 Capital Investment (New Starts and Small Starts) program funds. The funds will be... FY 2011, $1,596,800,000 was appropriated for the Capital Investments Grant Account, which includes...

Aloittelevan start-up yrittäjän opas rahoitukseen

OpenAIRE

Lamminsalo, Matti

2015-01-01

Opinnäytetyö käsittelee start-up rahoitusta ja siihen liittyviä toimintamalleja. Opinnäytetyön tuloksena on syntynyt opaskirja: Aloittelevan start-up yrittäjän opas rahoitukseen. Research about start-up ecosystem with investment aspect. As a result guidebook for start-up investment and how to raise a fund was writen.

STARTing Again: What Happens After START I Expires?

International Nuclear Information System (INIS)

Mladineo, Stephen V.; Durbin, Karyn R.; Eastman, Christina M.

2007-01-01

The Strategic Arms Reduction Treaty (START I), a seminal arms control agreement that substantially reduced the levels of deployed strategic nuclear arms in the United States and Russia, will expire in December 2009. At this time, it is unclear what - if anything - will replace it. While the treaty remains relevant, more than a simple extension is appropriate. Instead the authors advocate for a successor regime that builds on the START I legacy but does not rely on the traditional tools of arms control. This paper examines the strategic context in which a successor regime would be developed and proposes several recommendations for future action

From START to NEW START. The dilemma and future of nuclear disarmament

International Nuclear Information System (INIS)

Plettenberg, Lars

2012-01-01

The report describes the existing four agreements on nuclear disarmament: START I (1991). START II (1993), SORT (2002) and NEW START (2010). The chapter on the dependence between nuclear disarmament and strategic stability covers the issues mutual assured destruction (MAD), credibility, overkill capacity; the role of nuclear weapons in the national strategies of the USA and NATO, Russia, Great Britain, France, China and the other nuclear states. Ways out of MAD include disarmament, de-alerting and mutual assured protection (MAP).

Start-up of Rapsodie

International Nuclear Information System (INIS)

Pontier, R.

1967-01-01

After giving a general description of Rapsodie this report presents the conditions in which the start-up occurred and in which the tests were carried out. A chronological account is given of the operations and of the main events which occurred. The modifications made to the reactor during this period are described and a synthesis of the results obtained is presented. (author) [fr

Density and starting-energy dependent effective interaction

International Nuclear Information System (INIS)

Yamaguchi, Norio; Nagata, Sinobu; Kasuga, Teruo

1979-01-01

A new effective potential constructed from the reaction matrix calculation of nuclear matters is proposed, taking three-body effects into account. Starting from the two-body scattering equation for nuclear matters, an equation with averaged momentum is introduced as the definition of effective interaction. The parameters in the equation are the Fermi momentum and the starting energy. The nuclear density dependence and the starting energy dependence are independently treated in the potential. The effective interactions including three-body effects were calculated. The dependence on the starting energy is large. The effective interaction is more attractive in the triplet E state, and assures overall saturation without any artificial renormalization. The reaction matrix calculation can be well reproduced by the calculation with this effective potential. The results of calculation for the binding energy of He-4 and O-16 and the shell model matrix elements of O-16 are represented. (Kato, T.)

Sure start: voices of the 'hard-to-reach'.

Science.gov (United States)

Coe, C; Gibson, A; Spencer, N; Stuttaford, M

2008-07-01

This research aimed to look in depth at the factors affecting the ability of four Sure Start local programmes, based in a multicultural Midlands city, to engage with 'hard-to-reach' populations. A variety of research strategies and methods were employed. Geographical information systems, participatory research methods and interviews were used in order to understand the extent of the challenge, and hear first hand, why parents may not get involved with Sure Start. The mapping exercise involved collation and mapping of postcode data with respect to boundaries and potential and actual users of Sure Start services. This made possible the identification of any geographical patterning in the distribution of service users and non-users. Participatory research methods were used with parents, enabling them to conduct short interviews within their own communities and make sense of the data collected. Interviews were also conducted with 70 parents across the city, recruited through local schools. The results indicate that parental decisions regarding Sure Start are the product of a complex interaction between numerous factors which may act as either barriers or facilitators to service utilization. The results suggest that a multi-method approach to data collection is useful and appropriate in gaining access to those parents who are non-users of the Sure Start services and enabling their voices to be heard. These findings offer some explanations and insight into the apparent ambivalent attitudes of some families toward Sure Start services. Implications for future practice are discussed.

Sleep, sleepiness and school start times: a preliminary study.

Science.gov (United States)

Dexter, Donn; Bijwadia, Jagdeep; Schilling, Dana; Applebaugh, Gwendolyn

2003-01-01

High school students are reported to be excessively sleepy, resulting in decreased academic performance, increased psycho-social problems and increased risk of morbidity and mortality from accidents. Early school start times have been noted to contribute to this problem. This report attempts to confirm the relationship of early school start times with decreased sleep and increased sleepiness. We examined sophomore and junior students in 2 local high schools with different start times and measured the amount of time slept and sleepiness. We found that students at the early start school reported reduced sleep time and more sleepiness than their counterparts at the later starting school. Early school start times are associated with student reports of less sleep and increased sleepiness. Further studies in larger groups are recommended in view of the potential significant impact of sleep deprivation in this age group.

School Starting Age and Crime

DEFF Research Database (Denmark)

Landersø, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

This paper investigates the effects of school starting age on crime while relying on variation in school starting age induced by administrative rules; we exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise to a discontinuity in children......’s school starting age. Analyses are carried out using register-based Danish data. We find that higher age at school start lowers the propensity to commit crime, but that this reduction is caused by incapacitation while human capital accumulation is unaffected. Importantly, we also find that the individuals...

Gas Turbine Engine Starting Applicated on TV2-117 Turboshaft

Directory of Open Access Journals (Sweden)

R. M. Catana

2017-10-01

Full Text Available The paper presents the examination of two different types of engine starting configurations, applicated on TV2-117A turboshaft, running into the test bench. The first type of starting configuration is a normal starting, with the engine connected to the dynamometer which controls the free turbine speed by the dynamometer load. The second type of starting is a different one, the engine is not connected with the dynamometer, therefore it results that there is no control of the free turbine speed from the dynamometer, only from the engine but in particular conditions. To achieve the starting phase an instrumentation scheme is created, to control and monitor the engine, and a starting sequence with all the parameters, confirmations and commands that are involved into the starting phase. The engine starting is performed by the test bench operating system, composed of an acquisition system and a programmable controller, wherewith is running the starting sequence.

The start of the harvest

CERN Multimedia

2011-01-01

The first major particle physics summer conference has just started this week in Grenoble. After the Quark-Matter conference, the Europhysics Conference on High-Energy Physics marks the start of a promising harvest for the LHC experiments.   For the first time, the collaborations will be presenting their latest results based on all luminosity taken until end of June, which will provide more precise measurements in many areas. Thanks to the excellent performance of the LHC, the experiments have already accumulated a substantial quantity of data allowing them to push back the known limits and refine measurements in many fields ranging from b physics to the search for the Higgs boson and for dark matter. At the time of writing, the LHC collaborations are about to present these new results in an energy range which has never previously been explored. I have congratulated all the teams involved in getting the LHC into operation in record time with great efficiency. Today I would like to acknowledge the...

Start-up analysis of INET-5 MW district heating prototype reactor

International Nuclear Information System (INIS)

Li Tianshu

1991-09-01

The main features and thermohydraulic design parameters of the INET-5 MW reactor (INET: Institute of Nuclear Technology of Tsinghua University, Beijing) are presented. The start-up process and the effect of thermohydraulic instability on start-up process have been analyzed. The main obstacle of start-up process of INET-5 MW reactor is to pass the instability region from 1 atm to normal operation condition. For avoiding instability, the start-up process should be divided into two steps. The results of three different start-up proposals calculated by DACOL code are given and compared. The possibility of instabilities for each proposal has been checked. The checked results show that there is no instability during start-up of the three proposals. So, it is supposed that the INET-5 MW reactor can safely and stably reach the operation conditions. Finally, some conclusions about the effect of instability on start-up in boiling mode of INET-5MW reactor are given

Parameters matching requirements for diesel free piston linear alternator start-up

Directory of Open Access Journals (Sweden)

Yan-xiao Li

2015-03-01

Full Text Available It is important to identify the relationship between the starting requirements and the structure parameters of the diesel free piston linear alternator on the structural design stage. In this article, the forces applied on the moving part during the starting process are analyzed, and an oscillation model is established. The numerical simulation results of the oscillation model are presented, and the energy-transfer mechanism is analyzed. Then, the oscillation model is simplified by utilizing the energy balance theory. Expressions of the achieved starting frequency and required starting force are derived and the effects of different design variables on them are investigated. The results show that the achieved compression ratio is determined by the energy balance between the friction consumption and the energy supplied by the starting force. The starting frequency achieved and starting force required are associated with the cylinder bore, the moving mass, and effective stroke of the engine, which can be applied to the matching design and optimization of the prototype.

The Lean and Global Start-up

DEFF Research Database (Denmark)

Tanev, Stoyan; Rasmussen, Erik Stavnsager

For several decades researchers have studied start-up companies with a focus on international markets, suppliers and networks from their inception and on companies that are establishing new, agile business models. This has resulted in two streams of research: The Born Global and International New...... Ventures research and research with a focus on the Lean Start-up company. It is our intention in this paper to give a short presentation of the two research streams and show how they can be merged into one with a focus on newly established technology oriented firms that are lean and global from...

Start-up test of the prototype heavy water reactor 'FUGEN', (1)

International Nuclear Information System (INIS)

Ando, Hideki; Kawahara, Toshio

1982-01-01

The advanced thermal prototype reactor ''Fugen'' is a heavy water-moderated, boiling light water-cooled power reactor with electric output of 165 MW, which has been developed since 1966 as a national project. The start-up test was begun in March, 1978, being scheduled for about one year, and in March, 1979, it passed the final pre-use inspection and began the full scale operation. In this paper, the result of the start-up test of Fugen is reported. From the experience of the start-up test of Fugen, the following matters are important for the execution of start-up test. 1) Exact testing plan and work schedule, 2) the organization to perform the test, 3) the rapid evaluation of test results and the reflection to next testing plan, and 4) the reflection of test results to rated operation, regular inspection and so on. In the testing plan, the core characteristics peculiar to Fugen, and the features of heavy water-helium system, control system and other equipment were added to the contents of the start-up test of BWRs. The items of the start-up test were reactor physics test, plant equipment performance test, plant dynamic characteristic test, chemical and radiation measurement, and combined test. The organization to perform the start-up test, and the progress and the results of the test are reported. (Kako, I.)

1-D hybrid code for FRM start-up

International Nuclear Information System (INIS)

Stark, R.A.; Miley, G.H.

1982-01-01

A one-D hybrid has been developed to study the start-up of the FRM via neutral-beam injection. The code uses a multi-group numerical model originally developed by J. Willenberg to describe fusion product dynamics in a solenoidal plasma. Earlier we described such a model for use in determining self-consistent ion currents and magnetic fields in FRM start-up. However, consideration of electron dynamics during start-up indicate that the electron current will oppose the injected ion current and may even foil the attempt to achieve reversal. For this reason, we have combined the multi-group ion (model) with a fluid treatment for electron dynamics to form the hybrid code FROST (Field Reversed One-dimensional STart-up). The details of this merger, along with sample results of operation of FROST, are given

START: the creation of a spherical tokamak

International Nuclear Information System (INIS)

Sykes, Alan

1992-01-01

The START (Small Tight Aspect Ratio Tokamak) plasma fusion experiment is now operational at AEA Fusion's Culham Laboratory. It is the world's first experiment to explore an extreme limit of the tokamak - the Spherical Tokamak - which theoretical studies predict may have substantial advantages in the search for economic fusion power. The Head of the START project, describes the concept, some of the initial experimental results and the possibility of developing a spherical tokamak power reactor. (author)

Starting an aphasia center?

Science.gov (United States)

Elman, Roberta J

2011-08-01

Starting an aphasia center can be an enormous challenge. This article provides initial issues to review and consider when deciding whether starting a new organization is right for you. Determining the need for the program in your community, the best size and possible affiliation for the organization, and available resources, as well as developing a business plan, marketing the program, and building awareness in the community, are some of the factors that are discussed. Specific examples related to starting the Aphasia Center of California are provided. © Thieme Medical Publishers.

Cold start-up condition model for heat recovery steam generators

International Nuclear Information System (INIS)

Sindareh-Esfahani, Peyman; Habibi-Siyahposh, Ehsan; Saffar-Avval, Majid; Ghaffari, Ali; Bakhtiari-Nejad, Firooz

2014-01-01

A dynamic modeling of Heat Recovery Steam Generator (HRSG) during cold start-up operation in Combined Cycle Power Plant (CCPP) is introduced. In order to characterize the essential dynamic behavior of the HRSG during cold start-up; Dynamic equations of all HRSG's components are developed based on energy and mass balances. To describe precisely the operation of HRSG; a method based on nonlinear estimated functions for thermodynamic properties is applied to estimate the model parameters. Model parameters are evaluated by a designed algorithm based on Genetic Algorithm (GA). A wide set of experimental data is used to validate HRSG model during cold start-up operation. The simulation results show the reliability and validity of the developed model for cold start-up operation. - Highlights: •Presenting a mathematical model for HRSGs cold start-up based on energy and mass balances. •A designed parameter identification algorithm based on GA is presented. •Application of experimental data in order to model and validate simulation results

An analysis of the sliding pressure start-up of SCWR

International Nuclear Information System (INIS)

Wang, F.; Yang, J.; Li, H.; Zhang, Y.; Zhang, J.; Shan, J.; Gou, J.; Zhang, B.; Chen, C.

2012-01-01

In this paper, the preliminary sliding pressure start-up system and scheme of supercritical water-cooled reactor in CGNPC (CGN-SCWR) were proposed. Thermal-hydraulic behavior in start-up procedures was analyzed in detail by employing advanced reactor subchannel analysis software ATHAS. The maximum cladding temperature (MCT for short) and core power of fuel assembly during the whole start-up process were investigated comparatively. The results show that the recommended start-up scheme meets the design requirements from the perspective of thermal-hydraulic. (authors)

NEW VENTURE CREATION: HOW START-UPS GROW?

Directory of Open Access Journals (Sweden)

AIDIN SALAMZADEH

Full Text Available ABSTRACT Start-ups, often seen as sources of innovation and change, are prone to failure and accordingly they are attracting considerable attention not least from policy makers and Government officials. However, the various new venture creation studies that have emerged since the early 1980s lack cohesiveness, and the domain remains controversial. This article not only exposes the limitations of the existing body of understanding on the topic but attempts to develop a more comprehensive and comprehendible framework for start up (new venture creation. To do so it uses the frameworks proposed by Whetten, and March and Smith to develop 11 propositions. The resultant model suggests that the creation of a start up involves the identification of an idea or opportunity by an entrepreneur who subsequently organizes a series of activities, mobilizes resources and creates competence using his/her networks in an environment in order to create value. It sheds light on the start-up (new venture creation process and has relevance for entrepreneurs, policy makers and researchers.

Starting lithium prophylaxis early v. late in bipolar disorder

DEFF Research Database (Denmark)

Kessing, Lars Vedel; Vradi, Eleni; Andersen, Per Kragh

2014-01-01

BACKGROUND: No study has investigated when preventive treatment with lithium should be initiated in bipolar disorder. AIMS: To compare response rates among patients with bipolar disorder starting treatment with lithium early v. late. METHOD: Nationwide registers were used to identify all patients...... with a diagnosis of bipolar disorder in psychiatric hospital settings who were prescribed lithium during the period 1995-2012 in Denmark (n = 4714). Lithium responders were defined as patients who, following a stabilisation lithium start-up period of 6 months, continued lithium monotherapy without being admitted...... to hospital. Early v. late intervention was defined in two ways: (a) start of lithium following first contact; and (b) start of lithium following a diagnosis of a single manic/mixed episode. RESULTS: Regardless of the definition used, patients who started lithium early had significantly decreased rates of non...

Start-Up Funding Intentions Among Nascent Nonprofit Entrepreneurs: An Exploratory Investigation

Directory of Open Access Journals (Sweden)

Fredrik O. Andersson

2018-04-01

Full Text Available This paper explores the start-up funding intentions of nascent nonprofit entrepreneurs, i.e., individuals in the process of creating a new formal nonprofit organization. The main questions being examined are from which sources nascent nonprofit entrepreneurs anticipate to obtain start-up funding from, how much start-up funding nascent nonprofit entrepreneurs anticipate they will need to formally launch their new nonprofit, and if there are any differences in funding intentions among nascent nonprofit entrepreneurs with and without previous start-up experience. The results from a survey of 103 nascent nonprofit entrepreneurs in Kansas City are presented and contrasted with existing research on funding of new nonprofit organizations. The results show an apparent preference for start-up funding from philanthropic grants and private donations, along with personal contributions of the founder(s.

Using Meta-Analysis to Explain Variation in Head Start Research Results: The Role of Research Design

Science.gov (United States)

Shager, Hilary M.; Schindler, Holly S.; Hart, Cassandra M.D.; Duncan, Greg J.; Magnuson, Katherine A.; Yoshikawa, Hirokazu

2010-01-01

Head Start was designed as a holistic intervention to improve economically disadvantaged, preschool-aged children's cognitive and social development by providing a comprehensive set of educational, health, nutritional, and social services, as well as opportunities for parent involvement (Zigler & Valentine, 1979). Given the current interest in ECE…

30 CFR 75.1913 - Starting aids.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Starting aids. 75.1913 Section 75.1913 Mineral... SAFETY STANDARDS-UNDERGROUND COAL MINES Diesel-Powered Equipment § 75.1913 Starting aids. (a) Volatile fuel starting aids shall be used in accordance with recommendations provided by the starting aid...

Press Start

Science.gov (United States)

Harteveld, Casper

This level sets the stage for the design philosophy called “Triadic Game Design” (TGD). This design philosophy can be summarized with the following sentence: it takes two to tango, but it takes three to design a meaningful game or a game with a purpose. Before the philosophy is further explained, this level will first delve into what is meant by a meaningful game or a game with a purpose. Many terms and definitions have seen the light and in this book I will specifically orient at digital games that aim to have an effect beyond the context of the game itself. Subsequently, a historical overview is given of the usage of games with a serious purpose which starts from the moment we human beings started to walk on our feet till our contemporary society. It turns out that we have been using games for all kinds of non-entertainment purposes for already quite a long time. With this introductory material in the back of our minds, I will explain the concept of TGD by means of a puzzle. After that, the protagonist of this book, the game Levee Patroller, is introduced. Based on the development of this game, the idea of TGD, which stresses to balance three different worlds, the worlds of Reality, Meaning, and Play, came into being. Interested? Then I suggest to quickly “press start!”

Start-up of NPP Krsko; Pokusno obratovanje NE Krsko

Energy Technology Data Exchange (ETDEWEB)

Spiler, J; Aralica, J [Nuklearna elektrana Krsko, Krsko (Yugoslavia)

1984-07-01

The report describes a review of start-up program and its realisation. There are also described some more significant start-up results with their evaluation. The most significant operation criteria are compared between NPP Krsko and other similar plants in the world. The comparison shows that after the first contractors and operation personnel efforts have been accomplished, our first nuclear power plant is a safe and reliable source of electric power. At the end there are listed NPP Krsko start-up recommendations and experience. (author)

Jump Starting Entrepreneurship

DEFF Research Database (Denmark)

Burcharth, Ana; Smith, Pernille; Frederiksen, Lars

How do laid-off employees become entrepreneurs after receiving a dream start into self-employment? This question is relevant for policy makers and entrepreneurship researchers alike since it raises the possibility of a reverse entrepreneurial opportunity, in which the chance of becoming an entrep......How do laid-off employees become entrepreneurs after receiving a dream start into self-employment? This question is relevant for policy makers and entrepreneurship researchers alike since it raises the possibility of a reverse entrepreneurial opportunity, in which the chance of becoming...... an entrepreneur emerges before the discovery of a profitable opportunity. We empirically examine this question on the unique setting of a corporate entrepreneurship program. In the midst of a corporate crisis, Nokia supported laid-off employees to start their own ventures under favorable conditions. We...... persevered in their endeavors and eventually became comfortable with their new career prospects. We discuss the psychological factors that impact career transition after organizational closure and theorize weather they encourage or discourage entrepreneurship....

Beyond Intentions--What Makes a Student Start a Firm?

Science.gov (United States)

Joensuu-Salo, Sanna; Varamäki, Elina; Viljamaa, Anmari

2015-01-01

Purpose: Entrepreneurial intentions have been extensively studied in student populations, with results suggesting that higher education does not promote formation of entrepreneurial intentions (e.g. Varamäki et al., 2013). However, the gap between intending to start a business and actually doing something to start one remains. The purpose of this…

76 FR 50813 - Major Capital Investment Projects; Guidance on News Starts/Small Starts Policies and Procedures

Science.gov (United States)

2011-08-16

... DEPARTMENT OF TRANSPORTATION Federal Transit Administration Major Capital Investment Projects; Guidance on News Starts/Small Starts Policies and Procedures AGENCY: Federal Transit Administration (FTA... Administration (FTA) to publish policy guidance on the New and Small Starts capital project review and evaluation...

Start-Up of FEL Oscillator from Shot Noise

International Nuclear Information System (INIS)

Kumar, V.; Krishnagopal, S.; Fawley, W.M.

2007-01-01

In free-electron laser (FEL) oscillators, as in self-amplified spontaneous emission (SASE) FELs, the buildup of cavity power starts from shot noise resulting from the discreteness of electronic charge. It is important to do the start-up analysis for the build-up of cavity power in order to fix the macropulse width from the electron accelerator such that the system reaches saturation. In this paper, we use the time-dependent simulation code GINGER [1]to perform this analysis. We present results of this analysis for the parameters of the Compact Ultrafast TErahertz FEL (CUTE-FEL) [2] being built at RRCAT

45 CFR 1308.21 - Parent participation and transition of children into Head Start and from Head Start to public...

Science.gov (United States)

2010-10-01

... into Head Start and from Head Start to public school. 1308.21 Section 1308.21 Public Welfare... AND HUMAN SERVICES THE ADMINISTRATION FOR CHILDREN, YOUTH AND FAMILIES, HEAD START PROGRAM HEAD START... Standards § 1308.21 Parent participation and transition of children into Head Start and from Head Start to...

The Impact of Head Start on Children, Families and Communities. Final Report of the Head Start Evaluation, Synthesis and Utilization Project. Executive Summary.

Science.gov (United States)

McKey, Ruth Hubbell; And Others

This report summarizes the results of a study on the impact of Head Start on children's cognitive and socioemotional development, on child health and health institutions in the community, on enrollees' families, and on communities where Head Start programs operate. After discussing the background and methodology of the study, the report concludes…

Process parameters for high quality on-contour starting of laser cutting of steel

NARCIS (Netherlands)

Meijer, C.Z.; Meijer, C.Z.; Meijer, J.; Bakkers, E.P.M.

1997-01-01

Laser cut initiation in full material usually results in a start hole with bad quality. Starting strategies have been developed to avoid these crater-like holes. Start areas were obtained showing almost the same quality as the rest of the cut. As a result of the experiments and literature research

Engine-start Control Strategy of P2 Parallel Hybrid Electric Vehicle

Science.gov (United States)

Xiangyang, Xu; Siqi, Zhao; Peng, Dong

2017-12-01

A smooth and fast engine-start process is important to parallel hybrid electric vehicles with an electric motor mounted in front of the transmission. However, there are some challenges during the engine-start control. Firstly, the electric motor must simultaneously provide a stable driving torque to ensure the drivability and a compensative torque to drag the engine before ignition. Secondly, engine-start time is a trade-off control objective because both fast start and smooth start have to be considered. To solve these problems, this paper first analyzed the resistance of the engine start process, and established a physic model in MATLAB/Simulink. Then a model-based coordinated control strategy among engine, motor and clutch was developed. Two basic control strategy during fast start and smooth start process were studied. Simulation results showed that the control objectives were realized by applying given control strategies, which can meet different requirement from the driver.

Spanish Instruction in Head Start and Dual Language Learners' Academic Achievement.

Science.gov (United States)

Miller, Elizabeth B

2017-09-01

Data from the Head Start Impact Study ( N = 1,141) and the Head Start Family and Child Experiences Survey, 2009 Cohort ( N = 825) were used to investigate whether Spanish instruction in Head Start differentially increased Spanish-speaking Dual Language Learners' (DLLs) academic achievement. Although hypothesized that Spanish instruction would be beneficial for DLLs' early literacy and math skills, results from residualized growth models showed there were no such positive associations. Somewhat surprisingly, DLL children instructed in Spanish had higher English receptive vocabulary skills at the end of the Head Start year than those not instructed, with children randomly assigned to Head Start and instructed in Spanish having the highest scores. Policy implications for Head Start-eligible Spanish-speaking DLLs are discussed.

Pre-start timing information is used to set final linear speed in a C-start manoeuvre.

Science.gov (United States)

Reinel, Caroline; Schuster, Stefan

2014-08-15

In their unique hunting behaviour, archerfish use a complex motor decision to secure their prey: based solely on how dislodged prey initially falls, they select an adapted C-start manoeuvre that turns the fish right towards the point on the water surface where their prey will later land. Furthermore, they take off at a speed that is set so as to arrive in time. We show here that the C-start manoeuvre and not subsequent tail beating is necessary and sufficient for setting this adaptive level of speed. Furthermore, the C-start pattern is adjusted to independently determine both the turning angle and the take-off speed. The selection of both aspects requires no a priori information and is done based on information sampled from the onset of target motion until the C-start is launched. Fin strokes can occur right after the C-start manoeuvre but are not required to fine-tune take-off speed, but rather to maintain it. By probing the way in which the fish set their take-off speed in a wide range of conditions in which distance from the later catching point and time until impact varied widely and unpredictably, we found that the C-start manoeuvre is programmed based on pre-C-start estimates of distance and time until impact. Our study hence provides the first evidence for a C-start that is fine-tuned to produce an adaptive speed level. © 2014. Published by The Company of Biologists Ltd.

Preschool Facilities - MDC_HeadStart

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — A label (point) feature class of Head Start / Early Head Start/ Delegate Agencies/ Child Care Partnership & Family Day Care Homes Programs location in Miami-Dade...

Female Hires and the Success of Start-up Firms

OpenAIRE

Weber, Andrea; Zulehner, Christine

2009-01-01

In this paper we investigate the relationship between females among the first hires of start-up companies and business success. Our results show that firms with female first hires have a higher share of female workers at the end of the first year after entry. Further, we find that firms with female first hires are more successful and stay longer in the market. We conclude that our results support the hypothesis that gender-diversity in leading positions is an advantage for start-up firms.

Stop and Restart Effects on Modern Vehicle Starting System Components

Energy Technology Data Exchange (ETDEWEB)

Windover, Paul R. [Argonne National Lab. (ANL), Argonne, IL (United States); Owens, Russell J. [Argonne National Lab. (ANL), Argonne, IL (United States); Levinson, Terry M. [Argonne National Lab. (ANL), Argonne, IL (United States); Laughlin, Michael [Argonne National Lab. (ANL), Argonne, IL (United States); Gaines, Linda [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-01-01

Many drivers of personal and commercial vehicles believe that turning the vehicle off and on frequently instead of idling will cause premature wear of the starter system (starter motor and starter battery). As a result, they are concerned that the replacement cost of the starter motor and/or battery due to increased manual engine cycling would be more than the cumulative cost of the fuel saved by not idling unnecessarily. A number of variables play a role in addressing this complex concern, including the number of starting cycles per day, the time between starting cycles, the intended design life of the starting system, the amount of fuel used to restart an engine, and the cumulative cost of the saved fuel. Qualitative and quantitative information from a variety of sources was used to develop a life-cycle economic model to evaluate the cost and quantify the realistic factors that are related to the permissible frequency of starter motor cycles for the average vehicle to economically minimize engine idle time. Annual cost savings can be calculated depending on shutdown duration and the number of shutdown cycles per day. Analysis shows that cost savings are realized by eliminating idling exceeding one minute by shutting down the engine and restarting it. For a typical motorist, the damage to starting system components resulting from additional daily start cycles will be negligible. Overall, it was found that starter life is mostly dependent on the total number of start cycles, while battery life is more dependent on ensuring a full charge between start events.

Getting started with Unity

CERN Document Server

Felicia, Patrick

2013-01-01

Getting Started with Unity is written in an easy-to-follow tutorial format.""Getting Started with Unity"" is for[ 3D game developers[/color] who would like to learn how to use Unity3D and become familiar with its core features. This book is also suitable for intermediate users who would like to improve their skills. No prior knowledge of Unity3D is required.

Influence of decrease of the amount of starting salary of radiological technologists

International Nuclear Information System (INIS)

Shibuya, Koichi; Kato, Hirokazu

2010-01-01

This paper analyzes differences and changes within and between the occupation of nurses, radiological technologists, and medical technologists concerning starting salary from April 2005 to March 2009. This paper also investigates the percentage of difference in the amount of starting salary of nurses, radiological technologists, and medical technologists according to their educational attainments. The research-target used was the full-time-job-opening data provided to Okayama University within the given period of time, which specifies the amount of starting salary. The result shows that one's educational background has a crucial influence on the amount of one's starting salary. In fact, the percentage of the amount of starting salary base on one's educational attainment all increased in nurses, radiological technologists, and medical technologists from April 2007 to March 2009. However, this percentage for radiological technologists remains only 50% of increase, which was less significant than other two professional occupations. Moreover, the result indicates a crucial change in the amount of basic starting salary: while the amount of basic starting salary of nurses in 2008 has increased since 2005, that of radiological technologists has dropped remarkably. If this situation is not improved in the near future, the health-service sector may experience a decrease in the number of skilled practitioners which, in turn, will result in a decline in quality of medical care. (author)

Starting out

NARCIS (Netherlands)

Ans Merens; Freek Bucx

2018-01-01

Original title: Werken aan de start Women in the Netherlands have been outperforming men in education for many years now. However, this superior educational achievement does not translate into a better position on the labour market. More women work today than in the past, but still fewer than men.

Teaching iSTART to Understand Spanish

Science.gov (United States)

Dascalu, Mihai; Jacovina, Matthew E.; Soto, Christian M.; Allen, Laura K.; Dai, Jianmin; Guerrero, Tricia A.; McNamara, Danielle S.

2017-01-01

iSTART is a web-based reading comprehension tutor. A recent translation of iSTART from English to Spanish has made the system available to a new audience. In this paper, we outline several challenges that arose during the development process, specifically focusing on the algorithms that drive the feedback. Several iSTART activities encourage…

Mortality According to CD4 Count at Start of Combination Antiretroviral Therapy Among HIV-infected Patients Followed for up to 15 Years After Start of Treatment

DEFF Research Database (Denmark)

May, Margaret T; Vehreschild, Jorg-Janne; Trickey, Adam

2016-01-01

BACKGROUND: CD4 count at start of combination antiretroviral therapy (ART) is strongly associated with short-term survival, but its association with longer-term survival is less well characterized. METHODS: We estimated mortality rates (MRs) by time since start of ART (...-4.9, 5-9.9, and ≥10 years) among patients from 18 European and North American cohorts who started ART during 1996-2001. Piecewise exponential models stratified by cohort were used to estimate crude and adjusted (for sex, age, transmission risk, period of starting ART [1996-1997, 1998-1999, 2000......-2001], and AIDS and human immunodeficiency virus type 1 RNA at baseline) mortality rate ratios (MRRs) by CD4 count at start of ART (0-49, 50-99, 100-199, 200-349, 350-499, ≥500 cells/µL) overall and separately according to time since start of ART. RESULTS: A total of 6344 of 37 496 patients died during 359 219...

Soft-Starting Power-Factor Motor Controller

Science.gov (United States)

Nola, F. J.

1983-01-01

Three-phase power-factor controller with soft start is based on earlier version that does not control starting transients. Additional components serve to turn off "run" command signal and substitute gradual startup command signal during preset startup interval. Improved controller reduces large current surge that usually accompanies starting. Controller applies power smoothly, without causing motor vibrations.

What Happens at the Lesson Start?

Science.gov (United States)

Saloviita, Timo

2016-01-01

Transitional periods, such as lesson starts, are necessary steps from one activity to another, but they also compete with time for actual learning. The aim of the present study was to replicate a previous pilot study on lesson starts and explore possible disturbances. In total, 130 lesson starts in Finnish basic education in grades 1-9 were…

46 CFR 112.50-3 - Hydraulic starting.

Science.gov (United States)

2010-10-01

... POWER SYSTEMS Emergency Diesel and Gas Turbine Engine Driven Generator Sets § 112.50-3 Hydraulic starting. A hydraulic starting system must meet the following: (a) The hydraulic starting system must be a... 46 Shipping 4 2010-10-01 2010-10-01 false Hydraulic starting. 112.50-3 Section 112.50-3 Shipping...

Selection on start codons in prokaryotes and potential compensatory nucleotide substitutions.

Science.gov (United States)

Belinky, Frida; Rogozin, Igor B; Koonin, Eugene V

2017-09-29

Reconstruction of the evolution of start codons in 36 groups of closely related bacterial and archaeal genomes reveals purifying selection affecting AUG codons. The AUG starts are replaced by GUG and especially UUG significantly less frequently than expected under the neutral expectation derived from the frequencies of the respective nucleotide triplet substitutions in non-coding regions and in 4-fold degenerate sites. Thus, AUG is the optimal start codon that is actively maintained by purifying selection. However, purifying selection on start codons is significantly weaker than the selection on the same codons in coding sequences, although the switches between the codons result in conservative amino acid substitutions. The only exception is the AUG to UUG switch that is strongly selected against among start codons. Selection on start codons is most pronounced in evolutionarily conserved, highly expressed genes. Mutation of the start codon to a sub-optimal form (GUG or UUG) tends to be compensated by mutations in the Shine-Dalgarno sequence towards a stronger translation initiation signal. Together, all these findings indicate that in prokaryotes, translation start signals are subject to weak but significant selection for maximization of initiation rate and, consequently, protein production.

Two modes of wave propagation manifested in vertical electric dipole radiation over a sphere

International Nuclear Information System (INIS)

Houdzoumis, Vassilios A.

2000-01-01

The radiation of a vertical electric dipole over an electrically homogeneous sphere is considered anew, starting with a novel mathematical formulation. Both the dipole and the point of observation are assumed to lie on the spherical interface. The analysis is valid for a sphere whose radius is much larger than the wavelength in the outside region. Contributions to the value of the fields come, on the one hand, from the waves that propagate along the interface and, on the other hand, from the waves that propagate through the sphere by successive reflections. (c) 2000 American Geophysical Union

Jump2Health Website™ for Head Start parents to promote a healthy home environment: Results from formative research.

Science.gov (United States)

Gurajada, Navya; Reed, Debra B; Taylor, Ashlee L

2017-12-13

Background: In US, approximately 23% of children between the ages of 2-5 years are overweight or obese. Parents need access to information to create healthy home environments for obesity prevention, yet participation for in-person education programs is challenging. Web-based interventions are promising educational tools due to 24/7 availability. However, information is limited on their development and evaluation. Design and Methods: This study reports on a rigorous development process that included six focus group discussions (FGD) with stakeholders (three FGD each with parents and teachers) to assess education needs and inform the development of the Jump2Health Website ™ by a multidisciplinary team. After development, the Website was evaluated by telephone interviews with stakeholders (five parents and six teachers) and reviewed by an expert panel of five Registered Dietitians. Results: Twenty Head Start parents and 22 Head Start teachers participated in the FGD. To address the needs identified by these stakeholders, the Website was designed to include components that were enabling and motivating, such as descriptions of health benefits by achieving the desired behaviours, short videos on easy meal preparation, and tip sheets on how to achieve healthy behaviours in easy, economical ways. Stakeholder evaluation of the Website indicated that the information was helpful, easy to use, and would be beneficial for parents. Conclusions: The development of Jump2Health Website ™ was strengthened by FGD with stakeholders that assessed educational needs. Interviews with stakeholders and an expert panel review showed that the Website may be an effective educational method to teach parents about healthy behaviours related to obesity prevention.

Jump2Health Website™ for Head Start parents to promote a healthy home environment: Results from formative research

Directory of Open Access Journals (Sweden)

Navya Gurajada

2017-12-01

Full Text Available Background: In US, approximately 23% of children between the ages of 2-5 years are overweight or obese. Parents need access to information to create healthy home environments for obesity prevention, yet participation for in-person education programs is challenging. Web-based interventions are promising educational tools due to 24/7 availability. However, information is limited on their development and evaluation. Design and Methods: This study reports on a rigorous development process that included six focus group discussions (FGD with stakeholders (three FGD each with parents and teachers to assess education needs and inform the development of the Jump2Health Website™ by a multidisciplinary team. After development, the Website was evaluated by telephone interviews with stakeholders (five parents and six teachers and reviewed by an expert panel of five Registered Dietitians. Results: Twenty Head Start parents and 22 Head Start teachers participated in the FGD. To address the needs identified by these stakeholders, the Website was designed to include components that were enabling and motivating, such as descriptions of health benefits by achieving the desired behaviours, short videos on easy meal preparation, and tip sheets on how to achieve healthy behaviours in easy, economical ways. Stakeholder evaluation of the Website indicated that the information was helpful, easy to use, and would be beneficial for parents. Conclusions: The development of Jump2Health Website™ was strengthened by FGD with stakeholders that assessed educational needs. Interviews with stakeholders and an expert panel review showed that the Website may be an effective educational method to teach parents about healthy behaviours related to obesity prevention.

Consideration of a non-baked start-up of a synchrotron light source

International Nuclear Information System (INIS)

Hori, Y.; Kobayashi, M.

1996-01-01

Vacuum baking of large complex uhv devices, such as synchrotron light sources, requires both careful design and consideration of potential problems regarding the operation and maintenance of the device. Intense synchrotron irradiation can be utilized for degassing; it is indeed necessary to achieve the required operating pressure in most light sources. To examine a non-baked start-up, the outgassing of non-baked chambers by SR irradiation was measured. Also, a non-baked start-up was carried out at the Photon Factory ring. Both results demonstrate the feasibility of a non-baked start-up of a light source. The experiments and results are described, together with several other problems which must be solved for a non-baked start-up. (Author)

Method of starting internal pumps of a nuclear reactor

International Nuclear Information System (INIS)

Kumagami, Shoji.

1985-01-01

Purpose: To reduce the noise effects by decreasing the invading current into the main line upon starting an internal pump type nuclear reactor adapted to forcively recycle the reactor water by a plurality of internal pumps. Method: A plurality of internal pumps are divided into several groups and, upon starting pumps belonging to the individual unit group, the starting instances for the respective pumps are deviated to reduce the surges applied to the main line and suppress the invading current lower to reduce the earth noises. As a result, effects caused to other devices or equipments can be moderated to improve the reliability. Furthermore, by actuating the respective pumps on every group units in a starting pattern along the orthogonal line, flow rate distribution in the reactor can be balanced. Then, the instability region during low rotation of pumps, that is, instability of the flow rate near the resonance frequency can be decreased. (Kawakami, Y.)

Scheduling with target start times

NARCIS (Netherlands)

Hoogeveen, J.A.; Velde, van de S.L.; Klein Haneveld, W.K.; Vrieze, O.J.; Kallenberg, L.C.M.

1997-01-01

We address the single-machine problem of scheduling n independent jobs subject to target start times. Target start times are essentially release times that may be violated at a certain cost. The goal is to minimize an objective function that is composed of total completion time and maximum

Application of intelligent soft start in asynchronous motor

Science.gov (United States)

Du, Xue; Ye, Ying; Wang, Yuelong; Peng, Lei; Zhang, Suying

2018-05-01

The starting way of three phase asynchronous motor has full voltage start and step-down start. Direct starting brings large current impact, causing excessive local temperature to the power grid and larger starting torque will also impact the motor equipment and affect the service life of the motor. Aim at the problem of large current and torque caused by start-up, an intelligent soft starter is proposed. Through the application of intelligent soft start on asynchronous motor, highlights its application advantage in motor control.

De-escalatory confidence-building measures after START

International Nuclear Information System (INIS)

Stockton, P.N.

1992-01-01

The very notion of examining de-escalatory CBMs in the context of the START negotiations appears odd. Given the immense progress in US-Soviet relations, of which the proposed START agreement is emblematic, the risk of the two nations stumbling to the brink of war seems increasingly remote. Why bother analyzing CBMs designed to help resolve such an improbable event? The obvious answer is that relations between the US and the Soviet Union - or whatever array of nations succeed it - could take an unforeseeable turn for the worse. Once ratified, the START agreement is supposed to remain in force for seven years, more than enough time for political tensions to return with a vengeance. This suggests a more prudent question: if our two nations do stumble to the brink of war, will the START agreement affect the prospect of de-escalatory CBMs? And if the US and Soviet Union pursue deeper force-reductions in a follow-on START II agreement, could that agreement be designed to facilitate more effective de-escalatory measures? This paper sets the stage for addressing such questions by outlining the START agreement and offering a brief overview of how START might affect the prospects for CBMs. Then, after examining some specific CBM proposals in light of START, an analysis will be made of the de-escalatory problems and opportunities that a Start II treaty might create

46 CFR 112.50-7 - Compressed air starting.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Compressed air starting. 112.50-7 Section 112.50-7... air starting. A compressed air starting system must meet the following: (a) The starting, charging... air compressors addressed in paragraph (c)(3)(i) of this section. (b) The compressed air starting...

Start Later, Sleep Later: School Start Times and Adolescent Sleep in Homeschool vs. Public/Private School Students

Science.gov (United States)

Meltzer, Lisa J.; Shaheed, Keisha; Ambler, Devon

2014-01-01

Homeschool students provide a naturalistic comparison group for later/flexible school start times. This study compared sleep patterns and sleep hygiene for homeschool students and public/private school students (grades 6-12). Public/private school students (n=245) and homeschool students (n=162) completed a survey about sleep patterns and sleep hygiene. Significant school group differences were found for weekday bedtime, wake time, and total sleep time, with homeschool students waking later and obtaining more sleep. Homeschool students had later school start times, waking at the same time that public/private school students were starting school. Public/private school students had poorer sleep hygiene practices, reporting more homework and use of technology in the hour before bed. Regardless of school type, technology in the bedroom was associated with shorter sleep duration. Later school start times may be a potential countermeasure for insufficient sleep in adolescents. Future studies should further examine the relationship between school start times and daytime outcomes, including academic performance, mood, and health. PMID:25315902

Steps to Successful Professional Development in Head Start

Science.gov (United States)

Trivette, Carol M.; Raab, Melinda; Dunst, Carl J.

2012-01-01

This article discusses the implications of utilizing coaching-mentoring strategies with Head Start teachers identified from the results of a study which used an evidence-based approach to professional development. Early childhood and coaching practices that formed the basis of the study are explained. Implications from the study results regarding…

Start-up processes’ efficiency of turbine jet engines

Directory of Open Access Journals (Sweden)

Jankowski Antoni

2016-12-01

Full Text Available The paper presents diagnoses of example start-up processes of drive units built in military aircraft operated in the Dęblin's “School of Eaglets” during the flight. The significance of this process is very important, especially from the point of view of flight safety, especially as it concerns the training aircraft, on which officer cadets-candidates for pilots are trained. The diagnosis of the start-up process was conducted using data from on-board flight recorders recorded during a flight training, whose aim was an emergency launch of particular drive units, and with the help of the so-called phase mapping of the selected operating parameters of the particular flight drive systems. The standard diagram of typical start-up systems was shown, while presenting their base subassemblies. At the end, the obtained results and the main problems that need intervention were commented, as well as further preventive activities were proposed.

Starting a business through a franchise

OpenAIRE

Dubravka Mahaček; Maja Martinko Lihtar

2013-01-01

A business can be launched by establishing a new entity, purchasing an existing entity or through a franc - hise. There are certain prerequisites for starting a business, the most important ones being a quality idea and start-up capital. Potential start-up difficulties are inadequate financing, existing competition as well as the process of building your own market position. By purchasing an existing business some risks may be avoided and the opportunity for gaining profit may ...

Critical Incidents of Growth in Nordic eHealth Service Start-Ups

Directory of Open Access Journals (Sweden)

Martti Saarela

2017-06-01

Full Text Available Digitalisation can revolutionise healthcare delivery and provide new business opportunities for innovative start-ups. Start-up businesses in the healthcare service sector are a promising source of new employment and innovations. The start-up stage is the most critical period for the survival of a business, as decisions made during the early stages have a definitive influence on success. This study seeks to clarify the early development of eHealth service start-ups. To summarise the research problem, the authors ask the following question: What are the critical incidents related to the early development of eHealth service start-ups? The units of analysis in this study are 14 Nordic eHealth service start-ups located in Sweden and Finland. The Critical Incident Technique (CIT and semi-structured interviews were applied for data collection. The results are of interest to the public sector, which plays an essential role in healthcare as a service producer, but also as a creator of the business conditions of and opportunities for small businesses.

Method of starting up PWR type reactor

International Nuclear Information System (INIS)

Kadokami, Akira; Ueno, Ryuji; Tsuge, Ayao; Onimura, Kichiro; Ochi, Tatsuya.

1988-01-01

Purpose: To start-up a PWR type reactor so as to effectively impregnate and concentrate corrosion inhibitors in intergranular corrosive faces. Method: Upon reactor start-up, after transferring from the warm zero output state to thermal power loaded state and injecting corrosion inhibitors, thermal power is returned to zero and, subsequently, increased up to a rated power. By selecting the thermal power upon injecting the corrosion inhibitors to a steam generator body, that is, by selecting a thermal power load that starts to boil in heat conduction tubes, feedwater in the clavis portion can be formed into an appropriate boiling convection and, accordingly, the corrosion inhibitors can be penetrated to the clevis portion at a higher rate and in a greater amount as compared with those under zero power condition. Subsequently, when the thermal power is reduced, a sub-cooled state is attained in the clevis portion, in which steams present in the intergranular corrosion faces in the heat conduction tubes are condensated. As a result, the corrosion inhibitors at high concentration are impregnated into the intergranular corrosive faces to provide excellent effects. (Kamimura, M.)

Radiation therapy of Graves' ophthalmopathy. 2; Therapy started time

Energy Technology Data Exchange (ETDEWEB)

Kawamura, Toshinori; Koga, Sukehiko (Fujita Health Univ., Toyoake, Aichi (Japan). School of Medicine)

1994-04-01

The difference in the improvement of exophthalmos according to the period of starting radiation therapy was investigated for 26 patients of thyroid ophthalmopathy, also taking thyroidism during radiation into consideration. A 4 MV X-ray was used to a total dose of 20 Gy per 2 weeks. The treatment value tended to be better for the patients in whom the period from the appearance of exophthalmos in an euthyroid condition to the start of radiation was less than 12 months; those of a longer period showed poorer improvement. Radiation treatment of a hyperthyroid condition also showed poor results and it was thought it was not an adequately long enough period for the radiation to take effect. As a result, it was considered that the radiation therapy shall be advantageous if started within 12 months after the appearance of exophthalmos in an euthyroid condition. (author).

Novel start-up circuit with enhanced power-up characteristic for bandgap references

DEFF Research Database (Denmark)

Tuan Vu, Cao; Wisland, Dag T.; Lande, Tor Sverre

This paper presents a new start-up circuit for low-power bandgap reference (BGR) voltage generators. The BGR is designed for providing a stable 0.3 V power supply for application in low power wireless sensor nodes. The BGR has an enhanced power-up characteristic and demonstrates a reduction...... of the total stand-by current. Simulated results confirm that the proposed start-up circuit does not affect the performance of the BGR even though the supply voltage (VDD) is higher and has more stable power-up characteristic than the conventional start-up circuits. The new start-up circuit is designed with 65...

Start-up test of Fukushima Daini Nuclear Power Station Unit No.3

International Nuclear Information System (INIS)

Inomata, Toshio; Umezu, Akira; Kajikawa, Makoto; Koibuchi, Hiroshi; Netsu, Nobuhiko.

1986-01-01

In Unit 3 of the Fukushima Nuclear Power Station II (daini), a BWR power plant of output 1,100 MW, commercial operation was started in June 1985. Its start-up test was finished successfully in about nine months. That is, new equipments introduced were demonstration tested. Though the items of testing are increased, the start-up test took short time, resulting in construction period only 54.7 months of the Unit 3, the shortest in the world. During the test, there was no scramming other than the planned. Described are the following: an outline of the Unit 3, the items of its improvement and standardization, including the new equipments, preparations for the start-up test, the start-up test and its evaluation. (Mori, K.)

First physical start-up for the first pulsed reactor in China

International Nuclear Information System (INIS)

Huang Wenlou; Tan Rilin; Xie Yuqi; Chai Songshan; Li Yingfa; He Qianming; Zhou Bin

1993-01-01

The characteristics and the test results of initial loading fuel and first physical start-up for the first pulsed reactor in China (PRC-1) are described. Safe measure to ensure safety of first physical start-up are also described. The experiments show that performances of PRC-1 are in accord with design requirements

Comparison of outcomes between emergent-start and planned-start peritoneal dialysis in incident ESRD patients: a prospective observational study.

Science.gov (United States)

Li, Wen-Yi; Wang, Yi-Cheng; Hwang, Shang-Jyh; Lin, Shih-Hua; Wu, Kwan-Dun; Chen, Yung-Ming

2017-12-11

The clinical consequences of starting chronic peritoneal dialysis (PD) after emergent dialysis via a temporary hemodialysis (HD) catheter has rarely been evaluated within a full spectrum of treated end-stage renal disease (ESRD). We investigated the longer-term outcomes of patients undergoing emergent-start PD in comparison with that of other practices of PD or HD in a prospective cohort of new-onset ESRD. This was a 2-year prospective observational study. We enrolled 507 incident ESRD patients, among them 111 chose PD (43 planned-start, 68 emergent-start) and 396 chose HD (116 planned-start, 280 emergent-start) as the long-term dialysis modality. The logistic regression model was used to identify variables associated with emergent-start dialysis. The Kaplan-Meier survival analysis was used to determine patient survival and technique failure. The propensity score-adjusted Cox regression model was used to identify factors associated with patient outcomes. During the 2-year follow-up, we observed 5 (4.5%) deaths, 15 (13.5%) death-censored technique failures (transfer to HD) and 3 (2.7%) renal transplantations occurring in the PD population. Lack of predialysis education, lower predialysis estimated glomerular filtration rate and serum albumin were predictors of being assigned to emergent dialysis initiation. The emergent starters of PD displayed similar risks of patient survival, technique failure and overall hospitalization, compared with the planned-start counterparts. By contrast, the concurrent planned-start and emergent-start HD patients with an arteriovenous fistula or graft were protected from early overall death and access infection-related mortality, compared with the emergent HD starters using a central venous catheter. In late-referred chronic kidney disease patients who have initiated emergent dialysis via a temporary HD catheter, post-initiation PD can be a safe and effective long-term treatment option. Nevertheless, due to the potential complications

Lean Start-up in Established Companies

DEFF Research Database (Denmark)

Goduscheit, René Chester

2018-01-01

Lean start-up is an emergent perspective on how entrepreneurs can bring new products and services to the market. This approach challenges the dominant role of lengthy business plans, linear product development processes, and seeking complete overview of the potential of the new products....../services before market launch. Instead it suggests that start-ups could benefit from a ‘minimum-viable product’ approach where products and services are launched when they contain critical features. The emphasis in the lean start-up approach is on business models rather than the elaborate business plan...... at the companies (strategy meetings, development workshops etc.). The aim is to shed light on the implications for companies that seek to employ lean start-up. These implications will be aimed at aspects like innovation management, organizational structure, customer relations etc....

Is 8:30 a.m. Still Too Early to Start School? A 10:00 a.m. School Start Time Improves Health and Performance of Students Aged 13–16

Directory of Open Access Journals (Sweden)

Paul Kelley

2017-12-01

Full Text Available While many studies have shown the benefits of later school starts, including better student attendance, higher test scores, and improved sleep duration, few have used starting times later than 9:00 a.m. Here we report on the implementation and impact of a 10 a.m. school start time for 13 to 16-year-old students. A 4-year observational study using a before-after-before (A-B-A design was carried out in an English state-funded high school. School start times were changed from 8:50 a.m. in study year 0, to 10 a.m. in years 1–2, and then back to 8:50 a.m. in year 3. Measures of student health (absence due to illness and academic performance (national examination results were used for all students. Implementing a 10 a.m. start saw a decrease in student illness after 2 years of over 50% (p < 0.0005 and effect size: Cohen's d = 1.07, and reverting to an 8:50 a.m. start reversed this improvement, leading to an increase of 30% in student illness (p < 0.0005 and Cohen's d = 0.47. The 10:00 a.m. start was associated with a 12% increase in the value-added number of students making good academic progress (in standard national examinations that was significant (<0.0005 and equivalent to 20% of the national benchmark. These results show that changing to a 10:00 a.m. high school start time can greatly reduce illness and improve academic performance. Implementing school start times later than 8:30 a.m., which may address the circadian delay in adolescents' sleep rhythms more effectively for evening chronotypes, appears to have few costs and substantial benefits.

An Alternative Starting Point for Fraction Instruction

Science.gov (United States)

Cortina, José Luis; Višnovská, Jana; Zúñiga, Claudia

2015-01-01

We analyze the results of a study conducted for the purpose of assessing the viability of an alternative starting point for teaching fractions. The alternative is based on Freudenthal's insights about fraction as comparison. It involves portraying the entities that unit fractions quantify as always being apart from the reference unit, instead of…

The impact of FinTech start-ups on incumbent retail banks' share prices

OpenAIRE

Li, Yinqiao; Spigt, Renée; Swinkels, Laurens

2017-01-01

Background: This study aims to clarify the role of FinTech digital banking start-ups in the financial industry. We examine the impact of the funding of such start-ups on the stock returns of 47 incumbent US retail banks for 2010 to 2016. Methods: To capture the importance of FinTech start-ups, we use data on both the dollar-volume of funding and number of deals. We relate these to the stock returns with panel data regression methods. Results: Our results indicate a positive relationship exist...

Drug Abuse Prevention Starts with Parents

Science.gov (United States)

... Stages Listen Español Text Size Email Print Share Drug Abuse Prevention Starts with Parents Page Content Article Body ... for a time when drugs may be offered. Drug abuse prevention starts with parents learning how to talk ...

Oral desensitization to milk: how to choose the starting dose!

Science.gov (United States)

Mori, Francesca; Pucci, Neri; Rossi, Maria Elisabetta; de Martino, Maurizio; Azzari, Chiara; Novembre, Elio

2010-01-01

Mori F, Pucci N, Rossi ME, de Martino M, Azzari C, Novembre E. Oral desensitization to milk: how to choose the starting dose! Pediatr Allergy Immunol 2010: 21: e450–e453. © 2009 John Wiley & Sons A/S A renewed interest in oral desensitization as treatment for food allergy has been observed in the last few years. We studied a novel method based on the end point skin prick test procedure to establish the starting dose for oral desensitization in a group of 30 children higly allergic to milk. The results (in terms of reactions to the first dose administered) were compared with a group of 20 children allergic to milk as well. Such control group started to swallow the same dose of 0.015 mg/ml of milk. None reacted to the first dose when administered according to the end point skin prick test. On the other side, ten out of 20 children (50%) from the control group showed mild allergic reactions to the first dose of milk. In conclusion the end point skin prick test procedure results safe and easy to be performed in each single child in order to find out the starting dose for oral desensitization to milk, also by taking into account the individual variability. PMID:19624618

Analysis of canned-motor pump jamming failure in start hot standby mode

International Nuclear Information System (INIS)

Mo Zhengyu; Liu Hua; Wu Chao; Li Haifeng; Yu Zhongbin

2009-01-01

The reason of a canned-motor pump start failure is deduced in this paper. It is shown that the undersized gap of the lower guide bearing causes the start failure. By the stripping inspection data, the design value of the guide bearing gap, the cumulative departure of manufacturing assembly and the preloading of the bearing liner lead to the undersized gap. The test result shows that the improved canned-motor pump can start up successfully. (authors)

Start-up tests of NSRR

International Nuclear Information System (INIS)

1976-12-01

Start up tests of the Nuclear Safety Research Reactor (NSRR) were carried out from June 25 to August 15, 1975. The course of tests is in three stage, i.e. critical approach and zero power, power-up and pulse operation. Performance of the reactor was shown to be in good agreement with the design specifications in both steady-state and pulse operations. Test procedures and the results are presented in four parts: (I) general, (II) zero-power tests, (III) power-up tests, and (IV) pulse operation tests. (auth.)

Marketingová strategie tenisového klubu Start Tenis Liberec

OpenAIRE

Vaňková, Kateřina

2015-01-01

Title: Marketing strategy of the tennis club Start Tenis Liberec. Objectives: This diploma work targets on marketing analysis of the tennis club Start Tenis Liberec. The main objective of the wortk is to find out the current marketing situation of the tennis club and suggest a strategy, which guarantees its better future progress. Methods: For the research and getting necessary informations, following analysis have been applied: PEST, SWOT, competition and resources analysis. Results: The wor...

Health Coordination Manual. Head Start Health Services.

Science.gov (United States)

Administration for Children, Youth, and Families (DHHS), Washington, DC. Head Start Bureau.

Part 1 of this manual on coordinating health care services for Head Start children provides an overview of what Head Start health staff should do to meet the medical, mental health, nutritional, and/or dental needs of Head Start children, staff, and family members. Offering examples, lists, action steps, and charts for clarification, part 2…

Can Research Design Explain Variation in Head Start Research Results? A Meta-Analysis of Cognitive and Achievement Outcomes

Science.gov (United States)

Shager, Hilary M.; Schindler, Holly S.; Magnuson, Katherine A.; Duncan, Greg J.; Yoshikawa, Hirokazu; Hart, Cassandra M. D.

2013-01-01

This study explores the extent to which differences in research design explain variation in Head Start program impacts. We employ meta-analytic techniques to predict effect sizes for cognitive and achievement outcomes as a function of the type and rigor of research design, quality and type of outcome measure, activity level of control group, and…

Correlation between fuel rack sticking and unintentional re-starting of EDG

Energy Technology Data Exchange (ETDEWEB)

Kim, Young Cheol; Chung, Woo geun; Kang, Seung Hee; Kim, Myeong hoon [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The Emergency Diesel Generator (EDG) was being tested after overhaul maintenance. While the EDG was running at the rated speed (450 rpm), an operator pressed the manual stop button. But the EDG failed to stop and unintentionally started again. After the unintentional re-start, the EDG maintained running speed of 340 rpm. In the category of a governing system, this paper analyzes the cause of unintentional restart of the EDG that unintentionally re-started and maintained a speed at 340 rpm. The results of the analysis were then verified by a test run. Finally, we identified a correlation between fuel rack sticking and unintentional re-starting of the EDG. An analysis was conducted to confirm the cause of an EDG which was unintentionally restarting and running at 340rpm (rated speed is 450 rpm). Through a test run, it was confirmed that the results of the analysis are correct. The cause of the EDG unintentionally restarting was that it still rotated at 55 rpm over the minimum starting speed at the moment when the shutdown cylinder stopped blocking the fuel, because of a stuck fuel rack at the R7 cylinder. At the same time, the fuel that had been supplied into the cylinders (combustion chamber) by the governing system exploded and the EDG restarted unintentionally.

The physics of tokamak start-up

International Nuclear Information System (INIS)

Mueller, D.

2013-01-01

Tokamak start-up on present-day devices usually relies on inductively induced voltage from a central solenoid. In some cases, inductive startup is assisted with auxiliary power from electron cyclotron radio frequency heating. International Thermonuclear Experimental Reactor, the National Spherical Torus Experiment Upgrade and JT60, now under construction, will make use of the understanding gained from present-day devices to ensure successful start-up. Design of a spherical tokamak (ST) with DT capability for nuclear component testing would require an alternative to a central solenoid because the small central column in an ST has insufficient space to provide shielding for the insulators in the solenoid. Alternative start-up techniques such as induction using outer poloidal field coils, electron Bernstein wave start-up, coaxial helicity injection, and point source helicity injection have been used with success, but require demonstration of scaling to higher plasma current

University Knowledge Spillovers & Regional Start-up Rates

DEFF Research Database (Denmark)

Hellerstedt, Karin; Wennberg, Karl; Frederiksen, Lars

2014-01-01

how characteristics of the economic and political milieu within each region influence the ratio of firm births. We find that knowledge spillovers from universities and firm-based R&D strongly affect the start-up rates for both high-tech firms and knowledge-intensive services firms. Further, the start......This chapter investigates how regional start-up rates in the knowledge-intensive services and high-tech industries are influenced by knowledge spillovers from both universities and firm-based R&D activities. Integrating insights from economic geography and organizational ecology into the literature......-up rate of knowledge-intensive service firms is tied more strongly to the supply of university educated individuals and the political regulatory regime within the municipality than start-ups in high-tech industries. This suggests that knowledge-intensive service-start-ups are more susceptible to both...

Flow Behavior Around a Fast-Starting Robotic Fish

Science.gov (United States)

Ma, Ganzhong; Currier, Todd; Modarres-Sadeghi, Yahya

2017-11-01

A robotic fish is used to study the flow behavior around the body of a fast-starting fish as it experiences a fast-start. The robotic fish is designed and built emulating a Northern Pike, Esox Lucius, which can accelerate at up to 245 m/s2. In previous studies, we had focused on the flow around the tail during the fast-start, by using a tail which acted flexibly in the preparatory stage and rigidly in the propulsive stage. We have extended that study by including the fish body in the experimental setup, where the body can bend into a C-shape, so that the influence of the body motion on the resulting flow around the structure can be understood as well. In the tests, the fish can rotate about a vertical axis, where a multi-axis force sensor measures flow forces acting on the body. Synchronized with the force measurement, flow visualizations using bubble image velocimetry are conducted, and the observed shed vortices are related to the peak forces observed during the maneuver.

Storage evaporator for vehicles with start-stop technology; Speicherverdampfer fuer Fahrzeuge mit Start-Stopp-Funktion

Energy Technology Data Exchange (ETDEWEB)

Wawzyniak, Markus; Link, Joachim [Behr GmbH und Co. KG, Stuttgart (Germany)

2013-04-15

Today, the use of engine start-stop technology - a system designed to cut fuel consumption when the vehicle stops or, in future applications, when vehicles are in coasting or ''sailing'' mode - is gaining ground in more and more vehicle classes. Shutting off the internal combustion engine, though, detrimentally affects cabin air conditioning because the belt-driven A/C compressor is likewise deactivated, thus bringing the vapor compression process to a standstill. As a result, during extended stop periods and in warm weather vent temperatures and air humidity rapidly increase.

Single phase induction motor with starting performance

Energy Technology Data Exchange (ETDEWEB)

Popescu, M.; Demeter, E. [Research Institute for Electrical Machines, ICPE-ME, Bucharest (Romania); Navrapescu, V. [University `Politehnica` Bucharest, Electrical Engineering Faculty Splaiul Independentei, Bucharest (Romania)

1997-12-31

The paper presents problems related to a special type of single phase induction motor. The main novelty consists in the use of a conducting (aluminium casted) shell distributed on the periferic region of the rotor. As a result the starting performance, as well as the rated ones, is much improved in comparison with the conventional construction. (orig.) 4 refs.

Changes in parents' spanking and reading as mechanisms for Head Start impacts on children.

Science.gov (United States)

Gershoff, Elizabeth T; Ansari, Arya; Purtell, Kelly M; Sexton, Holly R

2016-06-01

This study examined whether Head Start, the nation's main two-generation program for low-income families, benefits children in part through positive changes in parents' use of spanking and reading to children. Data were drawn from the 3-year-old cohort of the national evaluation of the Head Start program known as the Head Start Impact Study (N = 2,063). Results indicated that Head Start had small, indirect effects on children's spelling ability at Age 4 and their aggression at Age 4 through an increase in parents' reading to their children. Taken together, the results suggest that parents play a role in sustaining positive benefits of the Head Start program for children's behavior and literacy skills, one that could be enhanced with a greater emphasis on parent involvement and education. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

Multi-Objective Optimization of Start-up Strategy for Pumped Storage Units

Directory of Open Access Journals (Sweden)

Jinjiao Hou

2018-05-01

Full Text Available This paper proposes a multi-objective optimization method for the start-up strategy of pumped storage units (PSU for the first time. In the multi-objective optimization method, the speed rise time and the overshoot during the process of the start-up are taken as the objectives. A precise simulation platform is built for simulating the transient process of start-up, and for calculating the objectives based on the process. The Multi-objective Particle Swarm Optimization algorithm (MOPSO is adopted to optimize the widely applied start-up strategies based on one-stage direct guide vane control (DGVC, and two-stage DGVC. Based on the Pareto Front obtained, a multi-objective decision-making method based on the relative objective proximity is used to sort the solutions in the Pareto Front. Start-up strategy optimization for a PSU of a pumped storage power station in Jiangxi Province in China is conducted in experiments. The results show that: (1 compared with the single objective optimization, the proposed multi-objective optimization of start-up strategy not only greatly shortens the speed rise time and the speed overshoot, but also makes the speed curve quickly stabilize; (2 multi-objective optimization of strategy based on two-stage DGVC achieves better solution for a quick and smooth start-up of PSU than that of the strategy based on one-stage DGVC.

Making a Simple Self-Starting Electric Motor

Science.gov (United States)

Hong, Seok-In; Choi, Jung-In; Hong, Seok-Cheol

2009-01-01

A simple electric motor has a problem in that the current applied to the motor per se can rarely trigger its rotation. Usually such motors begin to rotate after the rotor is slightly turned by hand (i.e., manual starting). In a "self-starting" motor, the rotor starts to rotate spontaneously as soon as the current is applied. This paper describes…

Comparison of crossover and jab step start techniques for base stealing in baseball.

Science.gov (United States)

Miyanishi, Tomohisa; Endo, So; Nagahara, Ryu

2017-11-01

Base stealing is an important tactic for increasing the chance of scoring in baseball. This study aimed to compare the crossover step (CS) and jab step (JS) starts for base stealing start performance and to clarify the differences between CS and JS starts in terms of three-dimensional lower extremity joint kinetics. Twelve male baseball players performed CS and JS starts, during which their motion and the force they applied to the ground were simultaneously recorded using a motion-capture system and two force platforms. The results showed that the normalised average forward external power, the average forward-backward force exerted by the left leg, and the forward velocities of the whole body centre of gravity generated by both legs and the left leg were significantly higher for the JS start than for the CS start. Moreover, the positive work done by hip extension during the left leg push-off was two-times greater for the JS start than the CS start. In conclusion, this study has demonstrated that the jab step start may be the better technique for a base stealing start and that greater positive work produced by left hip extension is probably responsible for producing its larger forward ground reaction force.

Modelling ohmic confinement experiments on the START tokamak

International Nuclear Information System (INIS)

Roach, C.M.

1996-05-01

Ohmic confinement data from the tight aspect ratio tokamak START has been analysed using the ASTRA transport simulation code. Neoclassical expressions have been modified to describe tight aspect ratio configurations, and the comparison between START data and models of anomalous transport has been made quantitative using the standard χ 2 test from statistics. Four confinement models (T11, Rebut-Lallia-Watkins, Lackner-Gottardi, and Taroni et al's Bohm model) have been compared with the START data. Three of the models are found to simulate START's electron temperature data moderately well, while Taroni et al's Bohm model overestimates electron temperatures in START by an order of magnitude. Thus comparison with START data tends to discriminate against Bohm models; these models are pessimistic or ITER. (author)

University Start-ups: A Better Business Model

Science.gov (United States)

Dehn, J.; Webley, P. W.

2015-12-01

Many universities look to start-up companies as a way to attract faculty, supporting research and students as traditional federal sources become harder to come by. University affiliated start-up companies can apply for a broader suite of grants, as well as market their services to a broad customer base. Often university administrators see this as a potential panacea, but national statistics show this is not the case. Rarely do universities profit significantly from their start-ups. With a success rates of around 20%, most start-ups end up costing the university money as well as faculty-time. For the faculty, assuming they want to continue in academia, a start-up is often unattractive because it commonly leads out of academia. Running a successful business as well as maintaining a strong teaching and research load is almost impossible to do at the same time. Most business models and business professionals work outside of academia, and the models taught in business schools do not merge well in a university environment. To mitigate this a new business model is proposed where university start-ups are aligned with the academic and research missions of the university. A university start-up must work within the university, directly support research and students, and the work done maintaining the business be recognized as part of the faculty member's university obligations. This requires a complex conflict of interest management plan and for the companies to be non-profit in order to not jeopardize the university's status. This approach may not work well for all universities, but would be ideal for many to conserve resources and ensure a harmonious relationship with their start-ups and faculty.

Biomechanical Analysis of the Swim-Start: A Review

Directory of Open Access Journals (Sweden)

Julien Vantorre, Didier Chollet, Ludovic Seifert

2014-06-01

Full Text Available This review updates the swim-start state of the art from a biomechanical standpoint. We review the contribution of the swim-start to overall swimming performance, the effects of various swim-start strategies, and skill effects across the range of swim-start strategies identified in the literature. The main objective is to determine the techniques to focus on in swimming training in the contemporary context of the sport. The phases leading to key temporal events of the swim-start, like water entry, require adaptations to the swimmer’s chosen technique over the course of a performance; we thus define the swim-start as the moment when preparation for take-off begins to the moment when the swimming pattern begins. A secondary objective is to determine the role of adaptive variability as it emerges during the swim-start. Variability is contextualized as having a functional role and operating across multiple levels of analysis: inter-subject (expert versus non-expert, inter-trial or intra-subject (through repetitions of the same movement, and inter-preference (preferred versus non-preferred technique. Regarding skill effects, we assume that swim-start expertise is distinct from swim stroke expertise. Highly skilled swim-starts are distinguished in terms of several factors: reaction time from the start signal to the impulse on the block, including the control and regulation of foot force and foot orientation during take-off; appropriate amount of glide time before leg kicking commences; effective transition from leg kicking to break-out of full swimming with arm stroking; overall maximal leg and arm propulsion and minimal water resistance; and minimized energy expenditure through streamlined body position. Swimmers who are less expert at the swim-start spend more time in this phase and would benefit from training designed to reduce: (i the time between reaction to the start signal and impulse on the block, and (ii the time in transition (i

ECRH-assisted start-up in ITER

International Nuclear Information System (INIS)

Lloyd, B.; Carolan, P.G.; Warrick, C.D.

1996-07-01

In ITER, the electric field applied for ionisation and to ramp up the plasma current may be limited to ∼ 0.3 V/m. In this case, based on established theories of the avalanche process, it is shown that ohmic breakdown in ITER is only possible over a narrow range of pressure and magnetic error field. Therefore, ECRH may be necessary to provide robust and reliable start-up. ECRH can ensure prompt breakdown over a wide range of prefill pressure and error field and can also give control over the initial time and location of breakdown. For ECRH-assisted start-up in ITER, the power and pulse length requirements are essentially determined by the need to ensure burnthrough, i.e. complete ionisation of hydrogen and the transition to high ionisation states of impurities. A 0-D code (with inclusion of some 1-D effects) has been developed to analyse burnthrough in ITER. The 0-D simulations indicate that control of the deuterium density is the key factor for ensuring successful start-up in ITER, where the effects of neutral screening and dynamic fuelling by the ex-plasma volume are also crucial. It is concluded that without ECRH, successful start-up will only be possible over a very restricted range of parameters but 3MW of absorbed ECRH power will ensure reasonably robust start-up for a broad range of conditions with beryllium impurity. In the case of carbon impurity, even with an absorbed ECRH power of 5MW one may be restricted to low prefill pressure and/or low carbon concentration for successful start-up. (Author)

Two-Man Bobsled Push Start Analysis

Directory of Open Access Journals (Sweden)

Lopes Alexandre Dias

2016-04-01

Full Text Available The importance of push start times on bobsled performance was evidenced by some studies, but at this moment there is no article to the authors’ knowledge that describes the bobsled push start. Thus, the objectives of this study were to describe the two-man bobsled push start, analyze the differences between teams, and estimate the most important variable analyzed. We hypothesized that the pilot and brakeman athletes’ movement patterns during a bobsled pushing start can be described. The images used in this study were obtained during the men’s two-man XIV World Championship of Bobsled (2004. Fifteen best teams participating in the championship were recorded, and four start runs for each team were analyzed. The videos were captured by two digital video cameras. The pilot athletes were analyzed during the moment that they touched the lateral push bar of the sled, and the brakemen were analyzed during the first take-off and first landing. The teams were pooled in three groups of five teams using the final ranking of pushing time. We concluded that there was a distinct pattern movement for pilots and brakemen. The initial position of the majority of the pilots was localized slightly behind the bar. After touching the lateral bar, the pilots remained in a semi-squat position, pushing the sled forward in a pattern of marching movement. All brakemen used the board attached to the track as a support for both feet at the start. The brakeman gave the greatest contribution to break the inertia of the sled. There was no significant difference of movement between the three groups analyzed for the pilot and the brakeman.

Start time delays in operating room: Different perspectives

Directory of Open Access Journals (Sweden)

Babita Gupta

2011-01-01

Full Text Available Background: Healthcare expenditure is a serious concern, with escalating costs failing to meet the expectations of quality care. The treatment capacities are limited in a hospital setting and the operating rooms (ORs. Their optimal utilization is vital in efficient hospital management. Starting late means considerable wait time for staff, patients and waste of resources. We planned an audit to assess different perspectives of the residents in surgical specialities and anesthesia and OR staff nurses so as to know the causative factors of operative delay. This can help develop a practical model to decrease start time delays in operating room (ORs. Aims: An audit to assess different perspectives of the Operating room (OR staff with respect to the varied causative factors of operative delay in the OR. To aid in the development of a practical model to decrease start time delays in ORs and facilitate on-time starts at Jai Prakash Narayan Apex Trauma centre (JPNATC, All India Institute of Medical Sciences (AIIMS, New Delhi. Methods: We prepared a questionnaire seeking the five main reasons of delay as per their perspective. Results: The available data was analysed. Analysis of the data demonstrated the common causative factors in start time operative delays as: a lack of proper planning, deficiencies in team work, communication gap and limited availability of trained supporting staff. Conclusions: The preparation of the equipment and required material for the OR cases must be done well in advance. Utilization of newer technology enables timely booking and scheduling of cases. Improved inter-departmental coordination and compliance with preanesthetic instructions needs to be ensured. It is essential that the anesthesiologists perform their work promptly, well in time . and supervise the proceedings as the OR manager. This audit is a step forward in defining the need of effective OR planning for continuous quality improvement.

Enhancing start performance in the sport of skeleton

OpenAIRE

Colyer, Steffi

2015-01-01

A fast start is considered to be crucial in skeleton with marginal gains in start performance perceived to make meaningful improvements to overall chances of success. Currently, knowledge surrounding the underlying determinants of start performance is sparse and training practices are based on limited scientific evidence. A series of investigations were conducted to advance this understanding.Initial observations revealed similarities between dry-land push-starts and those on ice tracks. Howe...

GETTING READY: RESULTS OF A RANDOMIZED TRIAL OF A RELATIONSHIP-FOCUSED INTERVENTION ON THE PARENT–INFANT RELATIONSHIP IN RURAL EARLY HEAD START

Science.gov (United States)

KNOCHE, LISA L.; SHERIDAN, SUSAN M.; CLARKE, BRANDY L.; EDWARDS, CAROLYN POPE; MARVIN, CHRISTINE A.; CLINE, KEELY D.; KUPZYK, KEVIN A.

2014-01-01

The purpose of this study is to investigate the effects of a relational intervention (the Getting Ready intervention) on parenting behaviors supporting the parent–infant relationship for families enrolled in Early Head Start home-based programming. Two-hundred thirty-four parents and their children participated in the randomized study, with 42% of parents reporting education of less than a high-school diploma. Brief, semistructured parent–child interaction tasks were videotaped every 4 months over a16-month intervention period. Observational codes of parent–infant relationship behaviors included quality of three parental behaviors: warmth and sensitivity, support for learning, and encouragement of autonomy; two appropriateness indicators: support for learning and guidance/directives; and one amount indicator: constructive behaviors. Parents who participated in the Getting Ready intervention demonstrated higher quality interactions with their children that included enhanced quality of warmth and sensitivity, and support for their children’s autonomy than did parents in the control group. They also were more likely to use appropriate directives with their children and more likely to demonstrate appropriate supports for their young children’s learning. Results indicate an added value of the Getting Ready intervention for Early Head Start home-based programming for families of infants and toddlers. PMID:24644374

On aNew Kind of Rays

Indian Academy of Sciences (India)

than glass free from lead. Ebonite several ... The English Translation of his German speech was also published in Nature, 53, 274, 1896, ... From these values it is clear that in no case can we obtain the transparency of a body from the product ...

Sprint Start Kinetics of Amputee and Non-Amputee Sprinters

Science.gov (United States)

Willwacher, Steffen; Herrmann, Volker; Heinrich, Kai; Funken, Johannes; Strutzenberger, Gerda; Goldmann, Jan-Peter; Braunstein, Björn; Brazil, Adam; Irwin, Gareth; Potthast, Wolfgang; Brüggemann, Gert-Peter

2016-01-01

The purpose of this study was to explore the relationship between the forces applied to the starting blocks and the start performances (SPs) of amputee sprinters (ASs) and non-amputee sprinters (NASs). SPs of 154 male and female NASs (100-m personal records [PRs], 9.58–14.00 s) and 7 male ASs (3 unilateral above knee, 3 unilateral below knee, 1 bilateral below knee; 100 m PRs, 11.70–12.70 s) with running specific prostheses (RSPs) were analysed during full-effort sprint starts using instrumented starting blocks that measured the applied forces in 3D. Using the NAS dataset and a combination of factor analysis and multiple regression techniques, we explored the relationship between force characteristics and SP (quantified by normalized average horizontal block power). Start kinetics were subsequently compared between ASs and NASs who were matched based on their absolute 100 m PR and their 100 m PR relative to the world record in their starting class. In NASs, 86% of the variance in SP was shared with five latent factors on which measured parameters related to force application to the rear and front blocks and the respective push-off directions in the sagittal plane of motion were loaded. Mediolateral force application had little influence on SP. The SP of ASs was significantly reduced compared to that of NASs matched on the basis of relative 100-m PR (−33.8%; d = 2.11, p < 0.001), while a non-significant performance reduction was observed when absolute 100-m PRs were used (−17.7%; d = 0.79, p = 0.09). These results are at least partially explained by the fact that force application to the rear block was clearly impaired in the affected legs of ASs. PMID:27846241

Sprint Start Kinetics of Amputee and Non-Amputee Sprinters.

Directory of Open Access Journals (Sweden)

Steffen Willwacher

Full Text Available The purpose of this study was to explore the relationship between the forces applied to the starting blocks and the start performances (SPs of amputee sprinters (ASs and non-amputee sprinters (NASs. SPs of 154 male and female NASs (100-m personal records [PRs], 9.58-14.00 s and 7 male ASs (3 unilateral above knee, 3 unilateral below knee, 1 bilateral below knee; 100 m PRs, 11.70-12.70 s with running specific prostheses (RSPs were analysed during full-effort sprint starts using instrumented starting blocks that measured the applied forces in 3D. Using the NAS dataset and a combination of factor analysis and multiple regression techniques, we explored the relationship between force characteristics and SP (quantified by normalized average horizontal block power. Start kinetics were subsequently compared between ASs and NASs who were matched based on their absolute 100 m PR and their 100 m PR relative to the world record in their starting class. In NASs, 86% of the variance in SP was shared with five latent factors on which measured parameters related to force application to the rear and front blocks and the respective push-off directions in the sagittal plane of motion were loaded. Mediolateral force application had little influence on SP. The SP of ASs was significantly reduced compared to that of NASs matched on the basis of relative 100-m PR (-33.8%; d = 2.11, p < 0.001, while a non-significant performance reduction was observed when absolute 100-m PRs were used (-17.7%; d = 0.79, p = 0.09. These results are at least partially explained by the fact that force application to the rear block was clearly impaired in the affected legs of ASs.

Predicting emergency diesel starting performance

International Nuclear Information System (INIS)

DeBey, T.M.

1989-01-01

The US Department of Energy effort to extend the operational lives of commercial nuclear power plants has examined methods for predicting the performance of specific equipment. This effort focuses on performance prediction as a means for reducing equipment surveillance, maintenance, and outages. Realizing these goals will result in nuclear plants that are more reliable, have lower maintenance costs, and have longer lives. This paper describes a monitoring system that has been developed to predict starting performance in emergency diesels. A prototype system has been built and tested on an engine at Sandia National Laboratories. 2 refs

FEMA DFIRM Station Start

Data.gov (United States)

Minnesota Department of Natural Resources — This table contains information about station starting locations. These locations indicate the reference point that was used as the origin for distance measurements...

Head Start Impact Study

Data.gov (United States)

U.S. Department of Health & Human Services — Nationally representative, longitudinal information from an evaluation where children were randomly assigned to Head Start or community services as usual;direct...

Linking Environmental Orientation to Start-ups’ Networking Activities

DEFF Research Database (Denmark)

Dickel, Petra; Ritter, Thomas

Besides for-profit start-ups, an increasing number of firms start their existence with the purpose to “do good” for society – mirrored in an increasing academic discussion of sustainable firms. Yet, there is little research on the networking activities of start-ups that do not have profit...... generation as their primary focus. Addressing this research gap, we develop hypotheses on the different networking activities of environmentally oriented start-ups arguing that their societal focus has a positive impact on the frequency of their networking and the size of their network. For empirically...... investigating such networking differences, we use data from 179 technology-based start-ups and show that start-ups with a strong external environmental orientation have significantly higher networking frequency and build larger networks. On the contrary, strong internal environmental orientation is linked...

Dampak Mentoring Pada Keberhasilan Start-Up Business: Studi Kasus Pada Start-Up Business di Indonesia [Mentoring the Impact of Success of a Start-Up Business: A Case Study of a Start-Up Business in Indonesia

OpenAIRE

Christina Yanita Setyawati

2016-01-01

Entrepreneurship is a highly developed science today, as well as in the world of education in Indonesia. Teaching entrepreneurship at the university level, especially at some universities in Surabaya, the second largest city in Indonesia, shows the positive impact that there were 74.03% of start-up businesses that survived and thrived in 2014. Based on the previous observation, some business start-ups are accompanied by a mentor. Mentoring is a process of forming and maintaining lasting relat...

Exhaust Emission Characteristics of Heavy Duty Diesel Engine During Cold and Warm Start

Directory of Open Access Journals (Sweden)

YANG Rong

2014-07-01

Full Text Available Through experiment conducted on a six cylinder direct injection diesel engine with SCR catalyst, effects of coolant temperature on rail pressure, injection quantity, excess air coefficient and emissions characteristics during cold and warm start were investigated. The results showed that, the maximum injection quantity during a starting event was several times higher than idling operation mode, so was the maximal opacity in the cold and warm starting process. When coolant temperature rose up to above 20℃, NOX emissions in the starting process exhibited peculiar rise which was times higher than idling mode. Compared with engine warm start, rail pressure, cycle fuel quantity, opacity, CO and HC emissions during engine cold start were higher in the course from their transient maximal values towards stabilized idling status. NOX in the same transient course, however, were lower in cold start. As coolant temperature rose, the maximal and the idling value of rail pressure and cycle fuel injection quantity during diesel engine starting process decreased gradually, the excess air coefficient increased to a certain degree, and the maximal and idling values of NOX increased gradually.

Early Head Start Evaluation

Data.gov (United States)

U.S. Department of Health & Human Services — Longitudinal information from an evaluation where children were randomly assigned to Early Head Start or community services as usual;direct assessments and...

Research on the intermediate process of a free-piston linear generator from cold start-up to stable operation: Numerical model and experimental results

International Nuclear Information System (INIS)

Feng, Huihua; Guo, Chendong; Jia, Boru; Zuo, Zhengxing; Guo, Yuyao; Roskilly, Tony

2016-01-01

Highlights: • The intermediate process of free-piston linear generator is investigated for the first time. • “Gradually switching strategy” is the best strategy in the intermediate process. • Switching at the top dead center position timing has the least influences on free-piston linear generator. • After the intermediate process, the operation parameters value is smaller than those before the intermediate process. - Abstract: The free-piston linear generator (FPLG) has more merits than the traditional reciprocating engines (TRE), and has been under extensive investigation. Researchers mainly investigated on the starting process and the stable generating process of FPLG, while there has not been any report on the intermediate process from the engine cold start-up to stable operation process. Therefore, this paper investigated the intermediate process of the FPLG in terms of switching strategy and switching position based on simulation results and test results. Results showed that when the motor force of the linear electric machine (LEM) declined gradually from 100% to 0% with an interval of 50%, and then to a resistance force in the opposite direction of piston velocity (generator mode), the operation parameters of the FPLG showed minimal changes. Meanwhile, the engine operated more smoothly when the LEM switched its working mode from a motor to a generator at the piston dead center, compared with that at the middle stroke or a random switching time. More importantly, after the intermediate process, the operation parameters of FPLG were smaller than that before the intermediate process. As a result, a gradual motor/generator switching strategy was recommended and the LEM was suggested to switch its working mode when the piston arrived its dead center in order to achieve smooth engine operation.

Head Start Impact Study. Technical Report

Science.gov (United States)

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This Technical Report is designed to provide technical detail to support the analysis and findings presented in the "Head Start Impact Study Final Report" (U.S. Department of Health and Human Services, January 2010). Chapter 1 provides an overview of the Head Start Impact Study and its findings. Chapter 2 provides technical information on the…

Inadvertent pump start with gas expansion modules

International Nuclear Information System (INIS)

Campbell, L.R.; Harris, R.A.; Heard, F.J.; Dautel, W.A.

1992-01-01

Previous testing demonstrated the effectiveness of gas expansion modules (GEMs) in mitigating the consequences of a loss-of-flow-without-scram transient in Fast Flux Test Facility (FFTF)-sized sodium cooled cores. As a result, GEMs have been included in the advance liquid-metal reactor (PRISM) design project sponsored by the US Department of Energy. The PRISM design is under review at the US Nuclear Regulatory Commission for licensability. In the unlikely event that the reactor does not scram during a loss of low, the GEMs quickly insert sufficient negative reactivity to limit fuel and cladding temperatures to acceptable values. This is the positive benefit of the GEMs; however, the reverse situation must be considered. A primary pump could be inadvertently started from near-critical conditions resulting in a positive reactivity insertion and a power transient. One mitigating aspect of this event is that as the reactivity associated with the GEMs is inserted, the increasing flow increases core cooling. A test was conducted in the FFTF to demonstrate that the GEM and feedback reactivity are well predicted following pump start, and the reactivity transient is benign

Low body weight and type of protease inhibitor predict discontinuation and treatment-limiting adverse drug reactions among HIV-infected patients starting a protease inhibitor regimen: consistent results from a randomized trial and an observational cohort

DEFF Research Database (Denmark)

Kirk, O; Gerstoft, J; Pedersen, C

2001-01-01

OBJECTIVES: To assess predictors for discontinuation and treatment-limiting adverse drug reactions (TLADR) among patients starting their first protease inhibitor (PI). METHODS: Data on patients starting a PI regimen (indinavir, ritonavir, ritonavir/saquinavir and saquinavir hard gel) in a randomi......OBJECTIVES: To assess predictors for discontinuation and treatment-limiting adverse drug reactions (TLADR) among patients starting their first protease inhibitor (PI). METHODS: Data on patients starting a PI regimen (indinavir, ritonavir, ritonavir/saquinavir and saquinavir hard gel....... Low body weight and initiation of ritonavir relative to other PIs were associated with an increased risk of TLADRs. Very consistent results were found in a randomized trial and an observational cohort....

Starting electronics

CERN Document Server

Brindley, Keith

2005-01-01

Starting Electronics is unrivalled as a highly practical introduction for hobbyists, students and technicians. Keith Brindley introduces readers to the functions of the main component types, their uses, and the basic principles of building and designing electronic circuits. Breadboard layouts make this very much a ready-to-run book for the experimenter; and the use of multimeter, but not oscilloscopes, puts this practical exploration of electronics within reach of every home enthusiast's pocket. The third edition has kept the simplicity and clarity of the original. New material

From BookStart to BookSmart : about the importance of an early start with parent-child reading

NARCIS (Netherlands)

Berg, Heleen van den

2015-01-01

BookStart has been developed to enhance parent-child verbal interactions in early childhood by promoting book sharing. Parents receive a voucher for a baby book and free access to baby books in the library. In a large-scale research, we found that if parents complied with the BookStart suggestion to

Improvement in motor performance during high pressure pump starting at NDDP, Kalpakkam

International Nuclear Information System (INIS)

Nagaraj, R.; Murugan, V.; Thalor, K.L.; Saxena, A.K.; Dangore, A.Y.; Prabhakar, S.; Tiwari, P.K.

2007-01-01

The major energy requirement required for a Sea Water Reverse Osmosis is in the form of Electrical Energy. The primary energy requirement in the process is the electrical energy fed to High Pressure Pumps to pressurize the feed sea water to membranes. This High pressure pump being a high inertia load requires very high torque at the time of starting. This high starting torque requirement results in increased acceleration time of the motor which subsequently increases the strain on the upstream electrical system from motor feeder to transformer. Such starting characteristic necessitates provision of special starting scheme for the high pressure pump motors. Sea water reverse osmosis (SWRO) plant of Nuclear Desalination Demonstration Project (NDDP) was commissioned in October 2002 at Kalpakkam, India. This paper presents the experiences of problems faced due to the typical starting characteristics of High Pressure pumps and provision of series reactor type motor starter for the same. (author)

Model based analysis of the time scales associated to pump start-ups

Energy Technology Data Exchange (ETDEWEB)

Dazin, Antoine, E-mail: antoine.dazin@lille.ensam.fr [Arts et métiers ParisTech/LML Laboratory UMR CNRS 8107, 8 bld Louis XIV, 59046 Lille cedex (France); Caignaert, Guy [Arts et métiers ParisTech/LML Laboratory UMR CNRS 8107, 8 bld Louis XIV, 59046 Lille cedex (France); Dauphin-Tanguy, Geneviève, E-mail: genevieve.dauphin-tanguy@ec-lille.fr [Univ Lille Nord de France, Ecole Centrale de Lille/CRISTAL UMR CNRS 9189, BP 48, 59651, Villeneuve d’Ascq cedex F 59000 (France)

2015-11-15

Highlights: • A dynamic model of a hydraulic system has been built. • Three periods in a pump start-up have been identified. • The time scales of each period have been estimated. • The parameters affecting the rapidity of a pump start-up have been explored. - Abstract: The paper refers to a non dimensional analysis of the behaviour of a hydraulic system during pump fast start-ups. The system is composed of a radial flow pump and its suction and delivery pipes. It is modelled using the bond graph methodology. The prediction of the model is validated by comparison to experimental results. An analysis of the time evolution of the terms acting on the total pump pressure is proposed. It allows for a decomposition of the start-up into three consecutive periods. The time scales associated with these periods are estimated. The effects of parameters (angular acceleration, final rotation speed, pipe length and resistance) affecting the start-up rapidity are then explored.

Start-up analysis for marketing strategy.

Science.gov (United States)

Griffith, M J; Baloff, N

1984-01-01

The complex start-up effect on utilization of health care services is too often overlooked or underestimated by marketing planners, leading to a range of negative consequences for both the users of services and the provider organization. Start-up analysis allows accurate estimation of these utilization effects for coordinated strategic planning among marketing finance, and operations.

Experience in the Kola NPP start-up works

International Nuclear Information System (INIS)

Zakharov, S.I.; Omel'chuk, V.V.; Bodrukhin, Yu.M.

1984-01-01

Main stages and peculiar features of maintenance and start-up works at WWER-440 type reactor NPPs described. Remarks revealed during complex equipment testing, physical and power start-up will be useful for arrangement of maintenance and start-up works at newly built NPPs

Start II, red ink, and Boris Yeltsin

International Nuclear Information System (INIS)

Arbatov, A.

1993-01-01

Apart from the vulnerability implied by the START II treaty, it will bear the burden of the general political opposition to the Yeltsin administration. START II will be seen as part of an overall Yeltsin-Andrei Kozyrev foreign policy that is under fire for selling out Russian national interests in Yugoslavia, the Persian Gulf, and elsewhere. This article discusses public opinion concerning START II, the cost of its implementation, and the general purpose of the treaty

Urbanization and start-up rates in different geographies: Belgium, the Netherlands and Sweden

OpenAIRE

Hans, Lianne; Koster, Sierdjan

2017-01-01

This study addresses the mediating role of settlement patterns in the relationship between urbanization and start-up activity. Places do not operate in a vacuum and to understand the effect of 'own' density on start-up patterns, we need to account for the urban spillovers or borrowed size that they may experience from other places nearby. The results can explain the empirical ambiguity in the relationship between urbanization and start-up patterns: the relationship between urbanization and st...

School Starting Age and the Crime-Age Profile

OpenAIRE

Landerso, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

2015-01-01

This paper uses register-based data to investigate the effects of school starting age on crime. Through this, we provide insights into the determinants of crime-age profiles. We exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise to a discontinuity in school starting age for children born around New Year. Our analysis speaks against a simple invariant crime-age profile as is popular in criminology: we find that higher school starting...

Allergic cross-reactivity – anew challenge for allergists?

Directory of Open Access Journals (Sweden)

Krzysztof Łukasz Piwowarek

2015-12-01

Full Text Available Allergic cross-reactivity is an important epidemiological issue in all age groups. It is caused by a non-specific binding of both primary allergen as well as allergens causing secondary cross-reactivity by the same IgE antibodies. This phenomenon results from the similarity of the molecular structure of allergen epitopes and leads to a number of allergic cross-reactivity syndromes, such as pollen-food syndromes, pork-cat syndrome or latex-fruit syndrome. They are characterized by rich symptomatology and the possible occurrence of symptoms related to various systems, including life-threatening systemic reactions. In many cases, specific allergen groups responsible for certain cross-reactions, such as plant profilins, fish parvalbumins or invertebrate tropomyosins, have been identified. Also, some of the factors affecting the spatial conformation of allergens, and thus modifying their allergenic potential, have been identified. Despite all these achievements, the diagnostics of cross reactivity syndromes still remains difficult due to the limited available methods and the possible occurrence of overlapping phenomena such as co-sensitisation, asymptomatic cross-sensitisation or IgE-independent or nonimmunological adverse drug reactions. Therefore, careful management based on medical history as well as avoidance of unjustified treatment methods, e.g. diet therapy or immunotherapy, are necessary. This is of great importance as the incidence of food allergies is expected to increase mainly due to the progressive rise in the prevalence of inhalant allergies to pollens.

Prediction of early race starts in Norwegian-Swedish Coldblooded Trotters

Directory of Open Access Journals (Sweden)

Ihler Carl F

2010-09-01

Full Text Available Abstract Background Less than a third of Norwegian-Swedish Coldblooded Trotters (NSCTs have started racing as three year olds since the year 2000 despite the fact that large sums are paid out as price-money in the three year season. Recruitment races are arranged by the Norwegian Trotting Association (NTA to stimulate early training. The management of young horses varies considerably and a large majority is reared by amateurs. The aim of the present study was to identify predictors of early race starts in young NSCT horses under field conditions. Methods Of the 801 registered NSCT horses born in 2005, 144 were randomly selected by stratified sampling with gender and paternal progeny as stratification factors. All horses were examined clinically. Further data were collected from NTA and by interviews of breeders, owners and trainers. The set of dependent variables consisted of "passed recruitment race", "start in regular race by the end of the three year season" and "start in regular race by the end of October in the four year season". Univariate and logistic regression analyses were performed. Results Genetic performance potential, as indicated by best linear unbiased prediction (BLUP indices, was the major predictor of the three dependent variables despite large variation in management. Dam's index was a better predictor than sire's index. However, the probability of early race starts in a horse with a low genetic performance potential can be increased by a favourable management. Examples of advantageous management factors in the present study were a flat pasture the first summer and early training. Nearly all horses racing in the three or four year seasons had passed a recruitment race in the two year season. Conclusions The results confirm the value of the published BLUP index as an important tool for the NSCT breeding program. Recruitment races stimulate early training.

Head Start Instructional Professionals' Inclusion Perceptions and Practices

Science.gov (United States)

Muccio, Leah S.; Kidd, Julie K.; White, C. Stephen; Burns, M. Susan

2014-01-01

This study considered the facilitators and barriers of successful inclusion in Head Start classrooms by examining the perspectives and practices of instructional professionals. A cross-sectional survey design was combined with direct observation in inclusive Head Start classrooms. Survey data were collected from 71 Head Start instructional…

Analysis of the repeatability of the exhaust pollutants emission research results for cold and hot starts under controlled driving cycle conditions.

Science.gov (United States)

Jaworski, Artur; Kuszewski, Hubert; Ustrzycki, Adam; Balawender, Krzysztof; Lejda, Kazimierz; Woś, Paweł

2018-04-20

Measurement of car engines exhaust pollutants emissions is very important because of their harmful effects on the environment. This article presents the assessment of repeatability of the passenger car engine exhaust pollutants emission research results obtained in the conditions of a chassis dynamometer. The research was conducted in a climate chamber, enabling the temperature conditions to be determined from - 20 to + 30 °C. The emission of CO, CH 4 , CO 2 , NO X , THC, and NMHC was subjected to the analysis. The aim of the research is to draw attention to the accuracy of the pollutant emission research results in driving cycles, and the comparison of pollutant emission results and their repeatability obtained in successive NEDC cycles under cold and hot start conditions. The results of the analysis show that, in the case of a small number of measurements, the results repeatability analysis is necessary for a proper interpretation of the pollutant emission results on the basis of the mean value. According to the authors' judgment, it is beneficial to determine the coefficient of variation for a more complete assessment of exhaust emission result repeatability obtained from a small number of measurements. This parameter is rarely presented by the authors of papers on exhaust components emission research.

Predicting start-up success with machine learning

OpenAIRE

Bento, Francisco Ramadas da Silva Ribeiro

2018-01-01

Start-ups are becoming the motor that moves our economy. Google, Apple, or more recently Airbnb and Uber are companies with tremendous impact in worldwide economy, social interactions and government. Over the past decade, both in the US and Europe, there has been an exponential growth in start-up formation. Thus, it seems a relevant challenge understanding what makes this type of high-risk ventures successful and as such, attractive to investors and entrepreneurs. Success for a start-up is de...

Standardization of the time for the execution of HANARO start-up and shutdown procedures

International Nuclear Information System (INIS)

Choi, H. Y.; Lim, I. C.; Hwang, S. R.; Kang, T. J.; Youn, D. B.

2003-01-01

For the standardization of the time to execute HANARO start-up and shutdown procedures, code names were assigned to the individual procedures and the work time were investigated. The data recorded by the operators during start-up and shutdown were statistically analyzed. The analysis results will be used for the standardization of start-up and shutdown procedures and it will be reflected in the procedure document

Getting started with SBT for Scala

CERN Document Server

Saxena, Shiti

2013-01-01

A practical and fast-paced guide, Getting Started with SBT for Scala walks you through the setup of Scala projects in SBT with sample code for common as well as critical scenarios.Getting Started with SBT for Scala is for developers working on Scala projects who are interested in learning and utilizing Simple Build Tool to manage the build process.

African entrepreneurs: An analysis of their motivation for starting their own business

Directory of Open Access Journals (Sweden)

BC Mitchell

2003-11-01

Full Text Available This study analyses the motivation of entrepreneurs for starting a business.  More specifically, it aims to identify whether entrepreneurs have common  motives for starting their own business, and whether men and women have  different reasons for becoming entrepreneurs. A motivation scale and openended  questions were used to measure motivation on a sample of more than 100  entrepreneurs. The results of a factor analysis indicate that entrepreneurs have  various reasons for starting a business, and are primarily motivated by the needs  for independence, material incentives and achievement.

Starting school: The effect of early childhood factors on child well-being

DEFF Research Database (Denmark)

Deding, Mette; Lausten, Mette; Rosenstjerne Andersen, Angelo

Children’s well-being around the age when they start school is crucial for their future success in the educational system. Factors in the first 3 years of a child’s life matter for the child’s well-being when he or she starts school. This article analyzes the relationship between early childhood...... factors–such as maternal employment, family structure, and family life–and future child well-being. The analysis uses the psychosocial SDQ-scale and the number of problems experienced around starting school as measures of well-being. Results show that family factors in particular are important, while...

Head Start at ages 3 and 4 versus Head Start followed by state pre-k: Which is more effective?

Science.gov (United States)

Jenkins, Jade Marcus; Farkas, George; Duncan, Greg J.; Burchinal, Margaret; Vandell, Deborah Lowe

2016-01-01

As policy-makers contemplate expanding preschool opportunities for low-income children, one possibility is to fund two, rather than one year of Head Start for children at ages 3 and 4. Another option is to offer one year of Head Start followed by one year of pre-k. We ask which of these options is more effective. We use data from the Oklahoma pre-k study to examine these two ‘pathways’ into kindergarten using regression discontinuity to estimate the effects of each age-4 program, and propensity score weighting to address selection. We find that children attending Head Start at age 3 develop stronger pre-reading skills in a high quality pre-kindergarten at age 4 compared with attending Head Start at age 4. Pre-k and Head Start were not differentially linked to improvements in children’s pre-writing skills or pre-math skills. This suggests that some impacts of early learning programs may be related to the sequencing of learning experiences to more academic programming. PMID:27076692

Photoemission starting of induction rf-driven multicusp ion sources

International Nuclear Information System (INIS)

Pickard, D.S.; Leung, K.N.; Perkins, L.T.; Ponce, D.M.; Young, A.T.

1996-01-01

It has been demonstrated that pulsed and continuous wave, rf-driven hydrogen discharges can be started with photoemission. The extracted H - current from a photoemission-started plasma has been investigated and does not differ significantly from that of a filament-started plasma. The minimum pressure for photoemissive starting was found to be higher than that of filament starting, 17 mTorr compared to 7 mTorr, respectively, in this particular configuration. copyright 1996 American Institute of Physics

Personality Traits and the Evaluation of Start-up Subsidies

NARCIS (Netherlands)

Caliendo, M.; Künn, Steffen; M., Weißenberger,

2016-01-01

Many countries support business start-ups to spur economic growth and reduce unemployment with different programmes. Evaluation studies of such programmes commonly rely on the conditional independence assumption (CIA), allowing a causal interpretation of the results only if all relevant variables

Start-up simulations of the PULSAR pulsed tokamak reactor

International Nuclear Information System (INIS)

Werley, K.A.; Bathke, C.G.

1993-01-01

Start-up conditions are examined for a pulsed tokamak reactor that uses only inductively driven plasma current (and bootstrap current). A zero-dimensional (profile-averaged) model containing plasma power and particle balance equations is used to study several aspects of plasma start-up, including: (1) optimization of the start-up pathway; (2) tradeoffs of auxiliary start-up heating power versus start-up time; (3) volt-second consumption; (4) thermal stability of the operating point; (5) estimates of the diverter heat flux and temperature during the start-up transient; (6) the sensitivity of the available operating space to allowed values of the H confinement factor; and (7) partial-power operations

On electrode erosion in fluorescent lamps during instant start

Energy Technology Data Exchange (ETDEWEB)

Hadrath, S.

2006-09-15

A fluorescent lamp driven with an 'instant start electronic control gear' starts in a glow mode. In the glow mode, which lasts typically for tens of milliseconds, the cathode fall exceeds hundreds of volts. This causes high energy ion bombardment of the electrode which heats the electrode, and induces a transition from glow to arc mode. In the arc mode the electrode emits thermionically and the cathode fall drops to the 12 - 15 V range. Unfortunately, the high energy ion bombardment during the glow mode leads also to intense sputtering of electrode material, including tungsten as well as emitter. Thus, instant started fluorescent lamps often suffer from early failures due to coil fracture. Therefore, the investigation of tungsten erosion during instant start is necessary and was the main goal of this work. The density of neutral atomic tungsten is determined by laser-induced fluorescence (LIF) and optical emission spectroscopy measurements (OES). Investigations are performed on a low-pressure argon dc discharge and on commercial fluorescent lamps. To include the entire temperature profile along the electrode the diffuse and spot operation modes of the dc lamp are studied experimentally and theoretically. The measured dependencies of the cathode temperature along the coil on the discharge and heating parameters are compared with the calculated results. For the first time the tungsten erosion during instant start of commercial fluorescent lamps was experimentally investigated in this work. The erosion process could be related to sputtering. A reconstruction of the temporal evolution of the absolute tungsten population density of the ground state during the glow mode was presented. The sputtered tungsten density increases immediately with the ignition, reaches a maximum where the discharge contracts at the end of the glow mode, and decreases some milliseconds before the glow-to-arc transition takes place. The maximum tungsten density was observed within a

Do Head Start Impacts Vary by Neighborhood Context?

Science.gov (United States)

Morris, Pamela A.; Connors, Maia C.; McCoy, Dana Charles; Gomez, Celia J.; Yoshikawa, Hiro; Aber, J. Lawrence

2014-01-01

This paper capitalizes on the addition of geocodes for Head Start centers in which children were randomly assigned to address questions about the role of neighborhood characteristics in moderating impacts of assignment to the Head Start program. Researchers explore the extent to which impacts of assignment to Head Start on outcomes for children…

Start-up Costs, Taxes and Innovative Entrepreneurship

NARCIS (Netherlands)

P. Darnihamedani (Pourya); J.H. Block (Jörn); S.J.A. Hessels (Jolanda); A. Simonyan (Aram)

2015-01-01

markdownabstract__Abstract__ Prior research suggests that start-up costs and taxes negatively influence entry into entrepreneurship. Yet, no distinction is made regarding the type of entrepreneurship, particularly innovative versus non-innovative entrepreneurship. Start-up costs, being one-off

The Impact of Head Start on Children, Families and Communities. Final Report of the Head Start Evaluation, Synthesis and Utilization Project.

Science.gov (United States)

McKey, Ruth Hubbell; And Others

Including all Head Start research (both published and unpublished) and using, when possible, the statistical technique of meta-analysis, this final report of the Head Start Evaluation, Synthesis, and Utilization Project presents findings on the impact of Head Start on children's cognitive and socioemotional development, on child health and health…

Tokamak start-up with electron-cyclotron heating

International Nuclear Information System (INIS)

Holly, D.J.; Prager, S.C.; Shepard, D.A.; Sprott, J.C.

1981-01-01

Experiments are described in which the start-up voltage in a tokamak is reduced by about a factor of two by the use of a modest amount of electron cyclotron resonance heating power for pre-ionization. The solution of the zero-dimensional start-up equations indicates that the effect is due to the high initial density which increases the rate at which the conductivity increases in the neutral-dominated initial plasma. The effect extrapolates favourably to larger tokamaks. A 50% reduction in the start-up volt-second requirement and impurity reflux is also observed. (author)

Tokamak start-up with electron-cyclotron heating

Energy Technology Data Exchange (ETDEWEB)

Holly, D J; Prager, S C; Shepard, D A; Sprott, J C [Wisconsin Univ., Madison (USA)

1981-11-01

Experiments are described in which the start-up voltage in a tokamak is reduced by about a factor of two by the use of a modest amount of electron cyclotron resonance heating power for pre-ionization. The solution of the zero-dimensional start-up equations indicates that the effect is due to the high initial density which increases the rate at which the conductivity increases in the neutral-dominated initial plasma. The effect extrapolates favourably to larger tokamaks. A 50% reduction in the start-up volt-second requirement and impurity reflux is also observed.

Integrated Marketing Strategies of German Companies : Start-Ups vs. Global Brands

OpenAIRE

Kostin, Irina

2016-01-01

The purpose of this bachelor's thesis is to find out and analyze different marketing strategies of German fashion companies. The main part is comparing relatively young start-up companies to established companies and analyzing to what extent the strategies differ. The methodology used in this paper were semi-structured expert interviews with German start-up companies. The results were analyzed and compared to the secondary research on the big global German companies. The findings showed that ...

School Starting Age and the Crime-Age Profile

DEFF Research Database (Denmark)

Landersø, Rasmus; Nielsen, Helena Skyt; Simonsen, Marianne

2017-01-01

This paper uses register-based data to investigate the effects of school starting age on crime. Through this, we provide insights into the determinants of crime-age profiles. We exploit that Danish children typically start first grade in the calendar year they turn seven, which gives rise...... to a discontinuity in school starting age for children born around New Year. Our analysis speaks against a simple invariant crime-age profile as is popular in criminology: we find that higher school starting age lowers the propensity to commit crime at young ages. We also find effects on the number of crimes...

Start Up Current Control of Buck-Boost Convertor-Fed Serial DC Motor

Directory of Open Access Journals (Sweden)

Yusuf SÖNMEZ

2009-02-01

Full Text Available Generally, DC motors are given preference for industrial applications such as electric locomotives, cranes, goods lifts. Because of they have high starting moment; they initially start with high current. This high start-up current must be decreased since it may damage windings of the motor and increases power consumption. It could be controlled by an appropriate driver system and controller. The nature of fuzzy logic control has adaptive characteristics that can achieve robust response to a system with uncertainty, parameter variation, and load disturbance. In this paper, fuzzy logic based control of start-up current of a Buck-Boost Converter fed serial DC motor is examined through computer simulation. In order to see the advantages of fuzzy logic control, classical PI control has applied to the same motor, under same circumstances and has been compared. C++ Builder software has been used for the simulation. According to the simulation results, plainly, fuzzy logic control has stronger responses than classical PI control and uses lower current at starting moment.

Long Pulse EBW Start-up Experiments in MAST

Directory of Open Access Journals (Sweden)

Shevchenko V.F.

2015-01-01

Full Text Available Start-up technique reported here relies on a double mode conversion (MC for electron Bernstein wave (EBW excitation. It consists of MC of the ordinary (O mode, entering the plasma from the low field side of the tokamak, into the extraordinary (X mode at a mirror-polarizer located at the high field side. The X mode propagates back to the plasma, passes through electron cyclotron resonance (ECR and experiences a subsequent X to EBW MC near the upper hybrid resonance (UHR. Finally the excited EBW mode is totally absorbed at the Doppler shifted ECR. The absorption of EBW remains high even in cold rarefied plasmas. Furthermore, EBW can generate significant plasma current giving the prospect of a fully solenoid-free plasma start-up. First experiments using this scheme were carried out on MAST [1]. Plasma currents up to 33 kA have been achieved using 28 GHz 100kW 90ms RF pulses. Recently experimental results were extended to longer RF pulses showing further increase of plasma currents generated by RF power alone. A record current of 73kA has been achieved with 450ms RF pulse of similar power. The current drive enhancement was mainly achieved due to RF pulse extension and further optimisation of the start-up scenario.

Multigenerational Head Start Participation: An Unexpected Marker of Progress

Science.gov (United States)

Chor, Elise

2018-01-01

One-quarter of the Head Start population has a mother who participated in the program as a child. This study uses experimental Head Start Impact Study (HSIS) data on 3- and 4-year-olds (N = 2,849) to describe multigenerational Head Start families and their program experiences. In sharp contrast to full-sample HSIS findings, Head Start has large,…

to start

Indian Academy of Sciences (India)

Click here to start. Table of contents. Slide 1 · Slide 2 · Slide 3 · Slide 4 · Slide 5 · Slide 6 · Slide 7 · Slide 8 · Slide 9 · Slide 10 · Slide 11 · Slide 12 · Slide 13 · Slide 14 · Slide 15 · Slide 16 · Slide 17 · Slide 18 · Slide 19 · Slide 20 · Slide 21 · Slide 22 · Slide 23 · Slide 24 · Slide 25 · Slide 26 · Slide 27 · Slide 28 · Slide 29 · Slide 30.

Effects of entrepreneurial orientation on start-up success: A gender perspective

Directory of Open Access Journals (Sweden)

Daisy Mui Hung Kee

2018-06-01

Full Text Available This paper examines the extent to which gender influences on the practice of Entrepreneurial Orien-tation (EO on Start-up Success. This study was conducted among Spin-off and Symbiosis Com-pany (SSC from all sectors in Peninsular Malaysia. Despite the remarkable research on EO and Start-up firms, there is a missing link on how gender provides different perspectives of EO practic-es among SSC, especially in Malaysia. A total of 120 SSC was chosen and the results show that EO was statistically related to Start-up Success and unveiled the magnitude of change that gender possesses in improving the relationship between EO practice and Start-up Success. The major implication of this study presents the unique contribution of gender in motivating SSC owners to engage in EO. Also, the difference of gender perceptions in business provides a variety of untapped opportunities in terms of entrepreneurial-related practices as different gender perceived different needs and capabilities. Future research is suggested to explore this phenomenon more extensively and develop a comprehensive model for the gender analysis. In brief, the discussion in this paper would help to strengthen the body of knowledge on Entrepreneurship and act as a future reference on SSC, EO, and Start-up Success.

Promoting School Success: Developing Social Skills and Early Literacy in Head Start Classrooms

Science.gov (United States)

Gunn, Barbara; Feil, Ed; Seeley, John; Severson, Herb; Walker, Hill M.

2006-01-01

This article reports the results of a pilot intervention to improve the social skills and literacy preparation of behaviorally at-risk Head Start children. Teachers in eight Head Start classrooms in two Oregon communities participated during the 2002-03 school year. Children in eight classrooms were screened and identified for participation using…

FUMEX-III Cases by START-3. Final Report

International Nuclear Information System (INIS)

Novikov, Vladimir; Bogatyr, Sergey; Kuznetsov, Vladimir; Chulkin, Dmitriy

2013-01-01

This document covers ''SUPER-RAMP'' and ''AREVA High-Burnup Idealised case'', cases of FUMEX-III project that were calculated by means of START-3 code. SUPER-RAMP PK-2 rodlets were chosen for calculation because they were subjected to strong power ramp and did not fail, because the main objective of the present calculations was to check the models of fission gas release and gaseous swelling of START-3 in the conditions of the power ramps (we did not intend to get the limit stresses for Zry-4 fuel rods). AREVA high burnup (PRIORITY CASE) case was chosen to check the applicability of the START-3 code to high-burnup PWR fuel rods behavior. Also, in order to check the stability and quality of the changes made into the code during the course of FUMEX-III participation, several simplified cases of FUMEX-II were recalculated. FUMEX-III SUPER-RAMP exercise included up to 49 kW/m power ramps of fuel rods with burnup up to 45 MWd/kgU. START-3 calculations of this exercise are in reasonable agreement with the experiment. AREVA high burnup priority case (∼81.5 MWd/kgU) was calculated and overprediction of the FGR was found. This overprediction is related with the conservative overestimation of rim-structure capability to retain fission gas and can be adjusted implementing a simple correction of this property. To verify the changes made into the code (oxide layer growth model and Zry-4 radiation growth), the corrected version of the code was used to recalculate the FUMEX-II simplified cases 27.2 and satisfactory results were obtained. (author)

Electrically heated catalysts for cold-start emission control on gasoline- and methanol-fueled vehicles

International Nuclear Information System (INIS)

Heimrich, M.J.; Albu, S.; Ahuja, M.

1992-01-01

Cold-start emissions from current technology vehicles equipped with catalytic converters can account for over 80 percent of the emissions produced during the Federal Test Procedure (FTP). Excessive pollutants can be emitted for a period of one to two minutes following cold engine starting, partially because the catalyst has not reached an efficient operating temperature. Electrically heated catalysts, which are heated prior to engine starting, have been identified as a potential strategy for controlling cold-start emissions. This paper summarizes the emission results of three gasoline-fueled and three methanol-fueled vehicles equipped with electrically heated catalyst systems. Results from these vehicles demonstrate that heated catalyst technology can provide FTP emission levels of nonmethane organic gases (NMOG), carbon monoxide (CO), and oxides of nitrogen (NO x ) that show promise of meeting the Ultra-Low Emission Vehicle (ULEV) standards established by the California Air Resources Board

The Impact of Start-up Grants on Firm Performance in Estonia

Directory of Open Access Journals (Sweden)

Siret Vildo

2013-01-01

Full Text Available As in economic theory start-up enterprises have been seen as important sources of growth, the government support measures to enterprises have been a common practice around the world for decades. As the governmental support to enterprises is often of a considerable amount of money there is a need to assess its efficiency. In the present article we study the impact of Estonian start-up grants distributed in 2002 and 2003 on various indicators of firm performance with econometric methods, namely propensity score matching. We use the data from the Estonian Business Register in order to study the impact of start-up grants on various economic indicators like the number of employees, turnover, equity, fixed assets and firm survival. The results showed that the start-up grants proved to affect positively the number of employed people and turnover, yet the impact on productivity was negative. One implication of the study is that it is difficult to achieve different goals to the same extent with a single governmental grant

Whi7 is an unstable cell-cycle repressor of the Start transcriptional program.

Science.gov (United States)

Gomar-Alba, Mercè; Méndez, Ester; Quilis, Inma; Bañó, M Carmen; Igual, J Carlos

2017-08-24

Start is the main decision point in eukaryotic cell cycle in which cells commit to a new round of cell division. It involves the irreversible activation of a transcriptional program by G1 CDK-cyclin complexes through the inactivation of Start transcriptional repressors, Whi5 in yeast or Rb in mammals. Here we provide novel keys of how Whi7, a protein related at sequence level to Whi5, represses Start. Whi7 is an unstable protein, degraded by the SCF Grr1 ubiquitin-ligase, whose stability is cell cycle regulated by CDK1 phosphorylation. Importantly, Whi7 associates to G1/S gene promoters in late G1 acting as a repressor of SBF-dependent transcription. Our results demonstrate that Whi7 is a genuine paralog of Whi5. In fact, both proteins collaborate in Start repression bringing to light that yeast cells, as occurs in mammalian cells, rely on the combined action of multiple transcriptional repressors to block Start transition.The commitment of cells to a new cycle of division involves inactivation of the Start transcriptional repressor Whi5. Here the authors show that the sequence related protein Whi7 associates to G1/S gene promoters in late G1 and collaborates with Whi5 in Start repression.

A novel high voltage start up circuit for an integrated switched mode power supply

Energy Technology Data Exchange (ETDEWEB)

Hu Hao; Chen Xingbi, E-mail: huhao21@uestc.edu.c [State Key Laboratory of Electronic Thin Films and Integrated Devices, University of Electronic Science and Technology of China, Chengdu 610054 (China)

2010-09-15

A novel high voltage start up circuit for providing an initial bias voltage to an integrated switched mode power supply (SMPS) is presented. An enhanced mode VDMOS transistor, the gate of which is biased by a floating p-island, is used to provide start up current and sustain high voltage. An NMOS transistor having a high source to ground breakdown voltage is included to extend the bias voltage range to the SMPS. Simulation results indicate that the high voltage start up circuit can start and restart as designed. The proposed structure is believed to be more energy saving and cost-effective compared with other solutions. (semiconductor devices)

Dynamic Modeling of Starting Aerodynamics and Stage Matching in an Axi-Centrifugal Compressor

Science.gov (United States)

Wilkes, Kevin; OBrien, Walter F.; Owen, A. Karl

1996-01-01

A DYNamic Turbine Engine Compressor Code (DYNTECC) has been modified to model speed transients from 0-100% of compressor design speed. The impetus for this enhancement was to investigate stage matching and stalling behavior during a start sequence as compared to rotating stall events above ground idle. The model can simulate speed and throttle excursions simultaneously as well as time varying bleed flow schedules. Results of a start simulation are presented and compared to experimental data obtained from an axi-centrifugal turboshaft engine and companion compressor rig. Stage by stage comparisons reveal the front stages to be operating in or near rotating stall through most of the start sequence. The model matches the starting operating line quite well in the forward stages with deviations appearing in the rearward stages near the start bleed. Overall, the performance of the model is very promising and adds significantly to the dynamic simulation capabilities of DYNTECC.

Innovative start-ups and young entrepreneurs: Definition of venturem capital and findings from Switzerland

Directory of Open Access Journals (Sweden)

Simon Zaby

2017-02-01

Full Text Available This paper aims to investigate success factors of innovative start-up firms from the perspective of young start-up managers. Which key factors did they experience before and since the foundation of their company? The experience from the quite young Swiss start-up scene pro-vides important insights to entrepreneurs and policy-makers in emerging countries that cur-rently face the necessity of building up a start-up environment. One part of the data has been collected by the author, the other part originates from the Swiss Venture Capital Database (total sample size: 306. The results show a significant role of venture capital financing for the success of innovative start-ups. Interestingly, this is to some extent because the start-ups see various additional benefits from venture capitalists involved in their firm. Thus, the findings shed new light on a proper definition of venture capital that should not solely focus on the flow of funds.

Tips for Starting Physical Activity

Science.gov (United States)

... Legislative Information Advisory & Coordinating Committees Strategic Plans & Reports Research Areas FAQs ... Starting Physical Activity Related Topics Section Navigation Tips to Help You Get Active ...

Joint kinetic determinants of starting block performance in athletic sprinting.

Science.gov (United States)

Brazil, Adam; Exell, Timothy; Wilson, Cassie; Willwacher, Steffen; Bezodis, Ian N; Irwin, Gareth

2018-07-01

The aim of this study was to explore the relationships between lower limb joint kinetics, external force production and starting block performance (normalised average horizontal power, NAHP). Seventeen male sprinters (100 m PB, 10.67 ± 0.32 s) performed maximal block starts from instrumented starting blocks (1000 Hz) whilst 3D kinematics (250 Hz) were also recorded during the block phase. Ankle, knee and hip resultant joint moment and power were calculated at the rear and front leg using inverse dynamics. Average horizontal force applied to the front (r = 0.46) and rear (r = 0.44) block explained 86% of the variance in NAHP. At the joint level, many "very likely" to "almost certain" relationships (r = 0.57 to 0.83) were found between joint kinetic data and the magnitude of horizontal force applied to each block although stepwise multiple regression revealed that 55% of the variance in NAHP was accounted for by rear ankle moment, front hip moment and front knee power. The current study provides novel insight into starting block performance and the relationships between lower limb joint kinetic and external kinetic data that can help inform physical and technical training practices for this skill.

46 CFR 112.50-5 - Electric starting.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Electric starting. 112.50-5 Section 112.50-5 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) ELECTRICAL ENGINEERING EMERGENCY LIGHTING AND POWER SYSTEMS Emergency Diesel and Gas Turbine Engine Driven Generator Sets § 112.50-5 Electric starting...

School Start Times, Sleep, Behavioral, Health, and Academic Outcomes: a Review of the Literature

Science.gov (United States)

Chapman, Daniel P.; Croft, Janet B.

2015-01-01

BACKGROUND Insufficient sleep in adolescents has been shown to be associated with a wide variety of adverse outcomes, from poor mental and physical health to behavioral problems and lower academic grades. However, most high school students do not get sufficient sleep. Delaying school start times for adolescents has been proposed as a policy change to address insufficient sleep in this population and potentially to improve students’ academic performance, reduce engagement in risk behaviors, and improve health. METHODS This paper reviews 38 reports examining the association between school start times, sleep, and other outcomes among adolescent students. RESULTS Most studies reviewed provide evidence that delaying school start time increases weeknight sleep duration among adolescents, primarily by delaying rise times. Most of the studies saw a significant increase in sleep duration even with relatively small delays in start times of half an hour or so. Later start times also generally correspond to improved attendance, less tardiness, less falling asleep in class, better grades, and fewer motor vehicle crashes. CONCLUSIONS Although additional research is necessary, research results that are already available should be disseminated to stakeholders to enable the development of evidence-based school policies. PMID:27040474

Start-up support for New Brunswick Electric's Point Lepreau nuclear steam generators

International Nuclear Information System (INIS)

Schneider, W.; Leroux, A.

1983-05-01

The start-up of the 600 MW Point Lepreau reactor provided the opportunity for direct involvement in the important low and medium power start-up phase which was of particular interest because this was a first-of-a-kind reactor type incorporating a new steam generator design. Support included test assistance and test results interpretation for the thermal hydraulic performance of the steam generators and in particular, investigation of water level response to operating pressure, power and feed flow. This work resulted in both a greatly improved understanding of transient characteristics and in a number of beneficial refinements in the control methods

Families & the North Carolina Smart Start Initiative.

Science.gov (United States)

Lowman, Betsy; Bryant, Donna; Zolotor, Adam

Smart Start is North Carolina's partnership between state government and local leaders, service providers, and families to better serve children under 6 years and their families. This study examined characteristics of families participating in Smart Start, their child care arrangements and family activities, and their need for and use of community…

En god start

DEFF Research Database (Denmark)

Sievertsen, Hans Henrik

I Danmark er det muligt at afvige fra reglen om, at barnet skal starte i skole det kalenderår, hvor barnet fylder 6 år. Det gør 10-15 procent af en årgang, mens 80-90 procent af børnene følger normen, og 2-3 procent starter i skole et år tidligere end normen, viser en analyse baseret på børn født i...

Automated start-up of EBR-II

International Nuclear Information System (INIS)

Kisner, R.A.

1989-01-01

Oak Ridge National Laboratory (ORNL) and Argonne National Laboratory (ANL) are undertaking a joint project to develop control philosophies, strategies, and algorithms for computer control of the start-up mode of the Experimental Breeder Reactor II (EBR-II). The major objective of this project is to show that advanced liquid-metal reactor (LMR) plants can be operated from low power to full power using computer control. Development of an automated control system with this objective in view will help resolve specific issues and provide proof through demonstration that automatic control for plant start-up is feasible. This paper describes the approach that will be used to develop such a system and some of the features it is expected to have. Structured, rule-based methods, which will provide start-up capability from a variety of initial plant conditions and degrees of equipment operability, will be used for accomplishing mode changes during plant start-up. Several innovative features will be incorporated such as signal, command, and strategy validation to maximize reliability, flexibility to accommodate a wide range of plant conditions, and overall utility. Continuous control design will utilize figures of merit to evaluate how well the controller meets the mission requirements. The operator interface will have unique ''look ahead'' features to let the operator see what will happen next. 15 refs., 7 figs., 1 tab

Relationship between different push-off variables and start performance in experienced swimmers.

Science.gov (United States)

García-Ramos, Amador; Feriche, Belén; de la Fuente, Blanca; Argüelles-Cienfuegos, Javier; Strojnik, Vojko; Strumbelj, Boro; Štirn, Igor

2015-01-01

The objective of this study was to determine the relationship between different variables measured with a force plate during the swimming start push-off phase and start performance presented by times to 5, 10 and 15 m. Twenty-one women from the Slovenian national swimming team performed two different swim starts (freestyle and undulatory) on a portable force plate to a distance further than 15 m. Correlations between push-off variables and times to 5, 10 and 15 m were quantified through Pearson's product-moment correlation coefficient (r). The variables that significantly correlated (p  .05). Based on the results of this study, we can conclude that horizontal take-off velocity and average horizontal acceleration (calculated as the average horizontal force divided by swimmer's body mass) are the variables most related to swimming start performance in experienced swimmers, and therefore could be the preferred measures to monitor swimmers' efficiency during the push-off phase.

Impact of reactor configuration on anammox process start-up: MBR versus SBR.

Science.gov (United States)

Tao, Yu; Gao, Da-Wen; Fu, Yuan; Wu, Wei-Min; Ren, Nan-Qi

2012-01-01

Anaerobic ammonium oxidation (anammox) is an energy saving biological nitrogen removal process which was limited to slow growth rate of anammox bacteria during start-up period. This study investigated the start-up of anammox process by a laboratory sequential batch reactor (SBR) for 218 days and subsequently modified the reactor as a membrane bioreactor (MBR) for 178 days. Modification of a SBR as MBR with installation of an external membrane module resulted in acceleration of specific anammox activity by 19 times. The acceleration of specific anammox activity with MBR was further confirmed by starting-up another MBR for a 242 day period. Molecular microbial analyses showed that Candidatus "Brocadia anammoxidans" and Candidatus "Kuenenia stuttgartiensis" were the dominant species in the inocula and biomass developed in the reactor. The start-up with MBR appeared to be more effective than SBR for the enrichment of anammox bacteria due to high sludge retention property of MBR configuration. Copyright © 2011 Elsevier Ltd. All rights reserved.

Study and application of digital physical start-up system for nuclear reactor

International Nuclear Information System (INIS)

Qu Ronghong; Li Baoxiang; Xu Xiaolin

2004-01-01

The digital physical start-up system for nuclear reactor is introduced. The system was used successfully in physical start-up experiment of 10 MW high-temperature gas-cooled reactor. It is proved practically that the system not only runs reliably and calculates both rapidly and correctly and relieves the loads of operators, but also has the better characters of monitoring and showing the real-time results of experiments than the analog systems. (author)

The economic implications of later school start times in the United States.

Science.gov (United States)

Hafner, Marco; Stepanek, Martin; Troxel, Wendy M

2017-12-01

Numerous studies have shown that later school start times (SST) are associated with positive student outcomes, including improvements in academic performance, mental and physical health, and public safety. While the benefits of later SST are very well documented in the literature, in practice there is opposition against delaying SST. A major argument against later SST is the claim that delaying SST will result in significant additional costs for schools due to changes in bussing strategies. However, to date, there has only been one published study that has quantified the potential economic benefits of later SST in relation to potential costs. The current study investigates the economic implications of later school start times by examining a policy experiment and its subsequent state-wide economic effects of a state-wide universal shift in school start times to 8.30AM. Using a novel macroeconomic modeling approach, the study estimates changes in the economic performance of 47 US states following a delayed school start time, which includes the benefits of higher academic performance of students and reduced car crash rates. The benefit-cost projections of this study suggest that delaying school start times is a cost-effective, population-level strategy, which could have a significant impact on public health and the US economy. From a policy perspective, these findings are crucial as they demonstrate that significant economic gains resulting from the delay in SST accrue over a relatively short period of time following the adoption of the policy shift. Copyright © 2017 National Sleep Foundation. Published by Elsevier Inc. All rights reserved.

A fast-starting mechanical fish that accelerates at 40 m s-2

International Nuclear Information System (INIS)

Conte, J; Modarres-Sadeghi, Y; Watts, M N; Hover, F S; Triantafyllou, M S

2010-01-01

We have built a simple mechanical system to emulate the fast-start performance of fish. The system consists of a thin metal beam covered by a urethane rubber, the fish body and an appropriately shaped tail. The body form of the mechanical fish was modeled after a pike species and selected because it is a widely-studied fast-start specialist. The mechanical fish was held in curvature and hung in water by two restraining lines, which were simultaneously released by a pneumatic cutting mechanism. The potential energy in the beam was transferred into the fluid, thereby accelerating the fish. We measured the resulting acceleration, and calculated the efficiency of propulsion for the mechanical fish model, defined as the ratio of the final kinetic energy of the fish and the initially stored potential energy in the body beam. We also ran a series of flow visualization tests to observe the resulting flow patterns. The maximum start-up acceleration was measured to be around 40 m s -2 , with the maximum final velocity around 1.2 m s -1 . The form of the measured acceleration signal as function of time is quite similar to that of type I fast-start motions studied by Harper and Blake (1991 J. Exp. Biol. 155 175-92). The hydrodynamic efficiency of the fish was found to be around 10%. Flow visualization of the mechanical fast-start wake was also analyzed, showing that the acceleration peaks are associated with the shedding of two vortex rings in near-lateral directions.

The start up as a phase of architectural design process.

Science.gov (United States)

Castro, Iara Sousa; Lima, Francisco de Paula Antunes; Duarte, Francisco José de Castro Moura

2012-01-01

Alterations made in the architectural design can be considered as a continuous process, from its conception to the moment a built environment is already in use. This article focuses on the "moving phase", which is the initial moment of the environment occupation and the start-up of services. It aims to show that the continuity of ergonomics interventions during the "moving phase" or start up may reveal the built environment inadequacies; clearly showing needs not met by the design and allowing making instant decisions to solve non-foreseen problems. The results have revealed some lessons experienced by users during a critical stage not usually included in the design process.

ATLAS starts moving in

CERN Multimedia

2004-01-01

The first large active detector component was lowered into the ATLAS cavern on 1 March. It consisted of the 8 modules forming the lower part of the central barrel of the tile hadronic calorimeter. The work of assembling the barrel, which comprises 64 modules, started the following day.

Product innovation and commercialization in lean global start-ups

DEFF Research Database (Denmark)

Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

2015-01-01

The paper examines the distinctive characteristics of product innovation and commercialization in Lean Global Start-up (LGS) – new technology firms which have adopted a lean and global path from or near to their inception. It suggests an uncertainty vs risk framework which allows integrating two...... research streams – Born Global (BG) firms and lean start-ups. In addition to its integrative theoretical value, the paper offers insights for lean start-up managers dealing with the challenges of a global start....

Environmental mitigation for SCC initiation of BWR core internals by hydrogen injection during start-up

International Nuclear Information System (INIS)

Dozaki, K.; Abe, A.; Nagata, N.; Takiguchi, H.

2004-01-01

Hydrogen injection into the reactor water has been applied to many BWR power stations. Since hydrogen injected accelerates recombination of oxidant generated by water radiolysis, oxidant concentration, such as dissolved oxygen concentration in reactor water can be reduced. As the result of the reduction of oxidant concentration, Electrochemical Corrosion Potential (ECP) at the surface of structural material can be lowered. Lowered ECP moderates Stress Corrosion Cracking (SCC) sensitivity of structural materials, such as stainless steels. As usual, hydrogen injection system begins to work after the plant start-up is finished, when the condition of normal operation is established. Accordingly, Hydrogen Water Chemistry (HWC) does not cover all the period of plant operation. As far as SCC crack growth is considered, loss of HWC during plant start-up does not result in significant crack growth, because of duration of plant start-up is much shorter than that of plant normal operation, when HWC condition is being satisfied. However, the reactor water environment and load conditions during a plant start-up may contribute to the initiation of SCC. It is estimated that the core internals are subjected to the strain rate that may cause susceptibility to SCC initiation during start-up. Dissolved oxygen (DO) and hydrogen peroxide (H 2 O 2 ) has a peak, and ECP is in high levels during start-up. Therefore it is beneficial to perform hydrogen injection during start-up as well in order to suppress SCC initiation. We call it HWC During Start-up (HDS) here. (orig.)

Starting a business through a franchise

Directory of Open Access Journals (Sweden)

Dubravka Mahaček

2013-12-01

Full Text Available A business can be launched by establishing a new entity, purchasing an existing entity or through a franc - hise. There are certain prerequisites for starting a business, the most important ones being a quality idea and start-up capital. Potential start-up difficulties are inadequate financing, existing competition as well as the process of building your own market position. By purchasing an existing business some risks may be avoided and the opportunity for gaining profit may arise. Profitable operation is possible only if this business has up-to-date products and no outstanding liabilities. This paper discusses franchising business opportunities and the requisite investments and costs, which will bring success if they are accompanied by franchisee’s efforts. The paper aims to present the main characteristics of a franchise business, the necessary investment and the costs which arise in the process, as well as advantages, disadvantages and experiences with this kind of business

Guidelines for starting today's private practice

Directory of Open Access Journals (Sweden)

Schmitz ED

2012-11-01

Full Text Available No abstract available. Article truncated at 150 words. Starting a new practice may seem like a daunting task. The purpose of this article is to demystify the process of creating a new practice from the beginning. The cardinal rule is to keep costs low and not to outsource work that can easily be performed by any competent physician and staff. You do not need a manager, lawyer, business partner, coder or biller individually; you may be able to perform many of these services yourself. What you do need is a commitment to making your practice a success. Do not spend too much on your office space, furnishings or equipment. Start with the bare essentials. Immediately start applying to all insurance companies especially Medicare. Request an employer identification number. Set up a basic business banking account and submit the account number to the insurance companies you plan to work with. You can purchase an entire electronic healthcare record (EHR …

40 CFR 86.536-78 - Engine starting and restarting.

Science.gov (United States)

2010-07-01

... equipped with automatic chokes shall be operated according to the instructions in the manufacturer's... transmission shall be placed in gear 15 seconds after the engine is started. If necessary, braking may be... starting procedure, the engine (automatic and manual choke engines) shall be started by opening the...

34 CFR 200.80 - Migrant Education Even Start Program definition.

Science.gov (United States)

2010-07-01

... 34 Education 1 2010-07-01 2010-07-01 false Migrant Education Even Start Program definition. 200.80... DISADVANTAGED Even Start Family Literacy Program § 200.80 Migrant Education Even Start Program definition. Eligible participants under the Migrant Education Even Start Program (MEES) must meet the definitions of a...

Start-up procedure

International Nuclear Information System (INIS)

Marchl, A.; Krebs, W.D.; Aleite, W.

1975-01-01

The start-up procedure will be shown on a pressurized water reactor, although most of the activities will occur similarly in other reactor types. The commissioning time can be divided into 5 sections, the phases A to E together lasting 26 months. Subsequently there are a test run of one month and the handling-over of the plant to the operator. A survey of the commissioning sections with several important main events is shown. (orig./TK) [de

Digital Marketing practices amongst start-up accelerators

OpenAIRE

Azinheiro, Marisa Filipa Ramos

2017-01-01

Digital Marketing (DM) is a vital marketing tool used by all types of companies nowadays. Accelerators are companies that appeared in the last few years to help start-ups grow and, just like any other company, they are using DM as well. This research explored which were the DM strategies used by accelerators. To do so, an online survey was shared amongst more than 300 accelerators across the world, whose results were analyzed by using SPSS Software. Correlation analyses and significance te...

The backstroke swimming start: state of the art.

Science.gov (United States)

de Jesus, Karla; de Jesus, Kelly; Fernandes, Ricardo J; Vilas-Boas, João Paulo; Sanders, Ross

2014-09-29

As sprint swimming events can be decided by margins as small as .01 s, thus, an effective start is essential. This study reviews and discusses the 'state of the art' literature regarding backstroke start biomechanics from 23 documents. These included two swimming specific publications, eight peer-reviewed journal articles, three from the Biomechanics and Medicine in Swimming Congress series, eight from the International Society of Biomechanics in Sports Conference Proceedings, one from a Biomechanics Congress and one academic (PhD) thesis. The studies had diverse aims, including swimmers' proficiency levels and data collection settings. There was no single consensus for defining phase descriptions; and kinematics, kinetics and EMG approaches were implemented in laboratory settings. However, researchers face great challenges in improving methods of quantifying valid, reliable and accurate data between laboratory and competition conditions. For example, starting time was defined from the starting signal to distances as disparate as ∼5 m to 22.86 m in several studies. Due to recent rule changes, some of the research outcomes now refer to obsolete backstroke start techniques, and only a few studies considered the actual international rules. This literature review indicated that further research is required, in both laboratory and competition settings focusing on the combined influences of the current rules and block configuration on backstroke starting performances.

START: An essential step in a new era

International Nuclear Information System (INIS)

Lockwood, D.

1991-01-01

After more than nine years of negotiations, the US and the Soviet Union signed the Strategic Arms Reduction Treaty (START) in Moscow on July 31, 1991. While the world has changed dramatically since 1982 when the START negotiations began, the treaty remains very much in the US interest. START exacts deep cuts in the most destabilizing and dangerous US and Soviet strategic weapons, and will lead to substantial overall reductions in the strategic nuclear forces of both sides. Moreover, the agreement will create a formal, structured, and predictable strategic environment. It will also impose on the Soviet Union or its successors a legally binding set of obligations that will be in effect for many years, regardless of changes in leadership or form of government. START, with its extensive series of intrusive, cooperative, and technical verification measures, will greatly enhance US knowledge about Soviet strategic nuclear forces and activities. The force reductions, predictability, and transparency that START will lock in will be especially valuable if the Soviet Union breaks into independent states or if there is a resurgence of hard-line political forces in Moscow. In addition, START will provide a framework for deeper reductions that could further reduce the risk of nuclear war, stimulate an increasingly cooperative relationship between the US and the Soviet Union or its successors, and save tens of billions of dollars. Finally, by demonstrating a US and Soviet commitment to reversing the arms race, START should reinforce efforts to stem the proliferation of nuclear weapons among both newly independent Soviet republics and nuclear threshold states, and to ensure success at the Nonproliferation Treaty (NPT) extension conference in 1995

20 CFR 404.241 - 1977 simplified old-start method.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false 1977 simplified old-start method. 404.241... DISABILITY INSURANCE (1950- ) Computing Primary Insurance Amounts Old-Start Method of Computing Primary Insurance Amounts § 404.241 1977 simplified old-start method. (a) Who is qualified. To qualify for the old...

FUEL SUPPLY IN ACCUMULATOR DIESEL SYSTEMS WITH ELECTRONIC CONTROL AT STARTING REGIME

Directory of Open Access Journals (Sweden)

G. M. Kuharenok

2009-01-01

Full Text Available The paper contains review and analysis of fuel supply process in accumulator diesel systems with electronic control at starting regime. The necessity has been shown to  develop and use programs of mathematic simulation pertaining to fuel supply processes with the purpose to decrease number of bench tests and time period required for a fuel system adaptation. The paper cites results of practical investigations on starting engines  equipped with the mentioned-above systems.

A fast novel soft-start circuit for peak current-mode DC—DC buck converters

International Nuclear Information System (INIS)

Li Jie; Yang Miao; Sun Weifeng; Lu Xiaoxia; Xu Shen; Lu Shengli

2013-01-01

A fully integrated soft-start circuit for DC—DC buck converters is presented. The proposed high speed soft-start circuit is made of two sections: an overshoot suppression circuit and an inrush current suppression circuit. The overshoot suppression circuit is presented to control the input of the error amplifier to make output voltage limit increase in steps without using an external capacitor. A variable clock signal is adopted in the inrush current suppression circuit to increase the duty cycle of the system and suppress the inrush current. The DC—DC converter with the proposed soft-start circuit has been fabricated with a standard 0.13 μm CMOS process. Experimental results show that the proposed high speed soft-start circuit has achieved less than 50 μs start-up time. The inductor current and the output voltage increase smoothly over the whole load range. (semiconductor integrated circuits)

Open-Start Mathematics Problems: An Approach to Assessing Problem Solving

Science.gov (United States)

Monaghan, John; Pool, Peter; Roper, Tom; Threlfall, John

2009-01-01

This article describes one type of mathematical problem, open-start problems, and discusses their potential for use in assessment. In open-start problems how one starts to address the problem can vary but they have a correct answer. We argue that the use of open-start problems in assessment could positively influence classroom mathematics…

Smart Start Evaluation Plan.

Science.gov (United States)

Bryant, Donna; Burchinal, Margaret; Buysse, Virginia; Kotch, Jonathan; Maxwell, Kelly; Neenan, Peter; Noblit, George; Orthner, Dennis; Peisner-Feinberg, Ellen; Telfair, Joseph

Smart Start is North Carolina's partnership between state government and local leaders, service providers, and families to better serve children under 6 years of age and their families. This report describes the comprehensive plan to evaluate the state and local goals and objectives of the program, focusing on the components addressing the…

Effect of wind fluctuating on self-starting aerodynamics characteristics of VAWT

Institute of Scientific and Technical Information of China (English)

朱建阳; 蒋林; 赵慧

2016-01-01

The present work deals with an investigation of the self-starting aerodynamic characteristics of VAWT under fluctuating wind. In contrast to the previous studies, the rotational speed of the turbine is not fixed, the rotation of the turbine is determined by the dynamic interaction between the fluctuating wind and turbine. A weak coupling method is developed to simulate the dynamic interaction between the fluctuating wind and passive rotation turbine, and the results show that if the fluctuating wind with appropriate fluctuation amplitude and frequency, the self-starting aerodynamic characteristics of VAWT will be enhanced. It is also found that compared with the fluctuation amplitude, the fluctuation frequency of the variation in wind velocity is shown to have a minor effect on the performance of the turbine. The analysis will provide straightforward physical insight into the self-starting aerodynamic characteristics of VAWT under fluctuating wind.

Personal and Public Start Pages in a library setting

NARCIS (Netherlands)

Kieft-Wondergem, Dorine

Personal and Public Start Pages are web-based resources. With these kind of tools it is possible to make your own free start page. A Start Page allows you to put all your web resources into one page, including blogs, email, podcasts, RSSfeeds. It is possible to share the content of the page with

Head Start Participants, Programs, Families and Staff in 2013

Science.gov (United States)

Walker, Christina

2014-01-01

Head Start programs provide poor children and their families with comprehensive early education and support services. Each year, programs are required to submit a Program Information Report (PIR) to the Office of Head Start on participating children, pregnant women, and families, as well as the staff serving the Head Start population. In 2013, the…

Reactor water quality degradation suppressing method upon reactor start up

International Nuclear Information System (INIS)

Maeda, Katsuharu.

1993-01-01

Preceding to reactor start-up, vacuum degree in a condenser is increased, and after the vacuum degree has been increased sufficiently, a desalting tower is inserted. Then, water feed to the reactor is started and the reactor is operated so that water is supplied gradually. Thus, dissolved oxygen in the feedwater and condensates is kept low and an entire organic carbon leaching rate from resins in the condensate desalting tower is reduced. Further, since feedwater is gradually supplied after the start-up, the entire organic carbon brought into the reactor is decomposed by heat and radiation and efficiently removed by a reactor coolant cleanup system. As a result, corrosion of stainless steel or the like is suppressed, as well as integrity of fuels can be maintained. Further, degradation of water quality can be suppressed effectively not by additionally putting the condensate desalting towers to in-service in accordance with the increase of the feedwater flow rate accompanying the power up but by previously putting the condensate desalting towers to in-service. (N.H.)

School start times for adolescents.

Science.gov (United States)

2014-09-01

The American Academy of Pediatrics recognizes insufficient sleep in adolescents as an important public health issue that significantly affects the health and safety, as well as the academic success, of our nation's middle and high school students. Although a number of factors, including biological changes in sleep associated with puberty, lifestyle choices, and academic demands, negatively affect middle and high school students' ability to obtain sufficient sleep, the evidence strongly implicates earlier school start times (ie, before 8:30 am) as a key modifiable contributor to insufficient sleep, as well as circadian rhythm disruption, in this population. Furthermore, a substantial body of research has now demonstrated that delaying school start times is an effective countermeasure to chronic sleep loss and has a wide range of potential benefits to students with regard to physical and mental health, safety, and academic achievement. The American Academy of Pediatrics strongly supports the efforts of school districts to optimize sleep in students and urges high schools and middle schools to aim for start times that allow students the opportunity to achieve optimal levels of sleep (8.5-9.5 hours) and to improve physical (eg, reduced obesity risk) and mental (eg, lower rates of depression) health, safety (eg, drowsy driving crashes), academic performance, and quality of life. Copyright © 2014 by the American Academy of Pediatrics.

Getting started with Go

CERN Multimedia

CERN. Geneva

2015-01-01

No, not the Chinese boardgame, the programming language that ironically Google made difficult to google for. You may have heard of Golang, and are wondering whether you should learn it. The answer is that of course you should, and this talk should explain why and point you at the best resources to get started.

Getting started with UDOO

CERN Document Server

Palazzetti, Emanuele

2015-01-01

If you are an Android developer who wants to learn how to use UDOO to build Android applications that are capable of interacting with their surrounding environment, then this book is ideal for you. Learning UDOO is the next great step to start building your first real-world prototypes powered by the Android operating system.

Ethnic Variation in the Association between Family Structures and Practices on Child Outcomes at 36 Months: Results from Early Head Start

Science.gov (United States)

Iruka, Iheoma U.

2009-01-01

Research Findings: This study analyzed data from the Early Head Start Research and Evaluation Study (EHSRES) to examine whether the association between family structural characteristics (maternal education, number of parents, employment status, and number of children), parenting practices (sensitive and negative parenting, cognitively stimulating…

TrustRank: a Cold-Start tolerant recommender system

Science.gov (United States)

Zou, Haitao; Gong, Zhiguo; Zhang, Nan; Zhao, Wei; Guo, Jingzhi

2015-02-01

The explosive growth of the World Wide Web leads to the fast advancing development of e-commerce techniques. Recommender systems, which use personalised information filtering techniques to generate a set of items suitable to a given user, have received considerable attention. User- and item-based algorithms are two popular techniques for the design of recommender systems. These two algorithms are known to have Cold-Start problems, i.e., they are unable to effectively handle Cold-Start users who have an extremely limited number of purchase records. In this paper, we develop TrustRank, a novel recommender system which handles the Cold-Start problem by leveraging the user-trust networks which are commonly available for e-commerce applications. A user-trust network is formed by friendships or trust relationships that users specify among them. While it is straightforward to conjecture that a user-trust network is helpful for improving the accuracy of recommendations, a key challenge for using user-trust network to facilitate Cold-Start users is that these users also tend to have a very limited number of trust relationships. To address this challenge, we propose a pre-processing propagation of the Cold-Start users' trust network. In particular, by applying the personalised PageRank algorithm, we expand the friends of a given user to include others with similar purchase records to his/her original friends. To make this propagation algorithm scalable to a large amount of users, as required by real-world recommender systems, we devise an iterative computation algorithm of the original personalised TrustRank which can incrementally compute trust vectors for Cold-Start users. We conduct extensive experiments to demonstrate the consistently improvement provided by our proposed algorithm over the existing recommender algorithms on the accuracy of recommendations for Cold-Start users.

Internal currents in PEMFC during start-up or shut-down

Energy Technology Data Exchange (ETDEWEB)

Maranzana, G.; Lottin, O.; Moyne, C.; Dillet, J.; Lamibrac, A.; Mainka, J.; Didierjean, S. [Nancy Univ. - CNRS (France). LEMTA

2010-07-01

Experiments show that the internal currents that occur during PEMFC start-up can reach up to 1 Acm{sup -2}. This is far more important than the expected order of magnitude of the current densities associated with carbon oxidation, which is only of a few mAcm{sup -2}. The predominant phenomenon that explains the internal currents is the charge and discharge of the double layer capacitances. A simple model with constant values of the electric parameters yields numerical results close to the experimental ones. It also explains the transient voltage rise (over the steady state open circuit voltage) that is sometimes observed experimentally shortly after the fuel cell start up. (orig.)

Are the new starting block facilities beneficial for backstroke start performance?

Science.gov (United States)

de Jesus, Karla; de Jesus, Kelly; Abraldes, J Arturo; Medeiros, Alexandre Igor Araripe; Fernandes, Ricardo J; Vilas-Boas, João Paulo

2016-01-01

We aimed to analyse the handgrip positioning and the wedge effects on the backstroke start performance and technique. Ten swimmers completed randomly eight 15 m backstroke starts (four with hands on highest horizontal and four on vertical handgrip) performed with and without wedge. One surface and one underwater camera recorded kinematic data. Standardised mean difference (SMD) and 95% confidence intervals (CI) were used. Handgrip positioning did not affect kinematics with and without wedge use. Handgrips horizontally positioned and feet over wedge displayed greater knee angular velocity than without it (SMD = -0.82; 95% CI: -1.56, -0.08). Hands vertically positioned and feet over wedge presented greater take-off angle (SMD = -0.81; 95% CI: -1.55, -0.07), centre of mass (CM) vertical positioning at first water contact (SMD = -0.97; 95% CI: -1.87, -0.07) and CM vertical velocity at CM immersion (SMD = 1.03; 95% CI: 0.08, 1.98) when comparing without wedge use. Swimmers extended the hip previous to the knee and ankle joints, except for the variant with hands vertically positioned without wedge (SMD = 0.75; 95% CI: -0.03, 1.53). Swimmers should preserve biomechanical advantages achieved during flight with variant with hands vertically positioned and wedge throughout entry and underwater phase.

Head Start at Ages 3 and 4 versus Head Start Followed by State Pre-K: Which Is More Effective?

Science.gov (United States)

Jenkins, Jade Marcus; Farkas, George; Duncan, Greg J.; Burchinal, Margaret; Vandell, Deborah Lowe

2016-01-01

As policy-makers contemplate expanding preschool opportunities for low-income children, one possibility is to fund two, rather than one year of Head Start for children at ages 3 and 4. Another option is to offer one year of Head Start followed by one year of pre-k. We ask which of these options is more effective. We use data from the Oklahoma…

Realizing a desired family size: when should couples start?

Science.gov (United States)

Habbema, J Dik F; Eijkemans, Marinus J C; Leridon, Henri; te Velde, Egbert R

2015-09-01

Until what age can couples wait to start a family without compromising their chances of realizing the desired number of children? The latest female age at which a couple should start trying to become pregnant strongly depends on the importance attached to achieving a desired family size and on whether or not IVF is an acceptable option in case no natural pregnancy occurs. It is well established that the treatment-independent and treatment-dependent chances of pregnancy decline with female age. However, research on the effect of age has focused on the chance of a first pregnancy and not on realizing more than one child. An established computer simulation model of fertility, updated with recent IVF success rates, was used to simulate a cohort of 10 000 couples in order to assess the chances of realizing a one-, two- or three-child family, for different female ages at which the couple starts trying to conceive. The model uses treatment-independent pregnancy chances and pregnancy chances after IVF/ICSI. In order to focus the discussion, we single out three levels of importance that couples could attach to realizing a desired family size: (i) Very important (equated with aiming for at least a 90% success chance). (ii) Important but not at all costs (equated with a 75% success chance) (iii) Good to have children, but a life without children is also fine (equated with a 50% success chance). In order to have a chance of at least 90% to realize a one-child family, couples should start trying to conceive when the female partner is 35 years of age or younger, in case IVF is an acceptable option. For two children, the latest starting age is 31 years, and for three children 28 years. Without IVF, couples should start no later than age 32 years for a one-child family, at 27 years for a two-child family, and at 23 years for three children. When couples accept 75% or lower chances of family completion, they can start 4-11 years later. The results appeared to be robust for

Psychiatric Advance Directives: Getting Started

Science.gov (United States)

... News Legal Issues Search for: About PADs A psychiatric advance directive (PAD) is a legal document that ... decisions during a mental health crisis. Getting Started Psychiatric advance directives (PADs) are relatively new legal instruments ...

A Parallel Restoration for Black Start of Microgrids Considering Characteristics of Distributed Generations

Directory of Open Access Journals (Sweden)

Jing Wang

2017-12-01

Full Text Available The black start capability is vital for microgrids, which can potentially improve the reliability of the power grid. This paper proposes a black start strategy for microgrids based on a parallel restoration strategy. Considering the characteristics of distributed generations (DGs, an evaluation model, which is used to assess the black start capability of DGs, is established by adopting the variation coefficient method. Thus, the DGs with good black start capability, which are selected by a diversity sequence method, are restored first in parallel under the constraints of DGs and network. During the selection process of recovery paths, line weight and node importance degree are proposed under the consideration of the node topological importance and the load importance as well as the backbone network restoration time. Therefore, the whole optimization of the reconstructed network is realized. Finally, the simulation results verify the feasibility and effectiveness of the strategy.

Classifier utility modeling and analysis of hypersonic inlet start/unstart considering training data costs

Science.gov (United States)

Chang, Juntao; Hu, Qinghua; Yu, Daren; Bao, Wen

2011-11-01

Start/unstart detection is one of the most important issues of hypersonic inlets and is also the foundation of protection control of scramjet. The inlet start/unstart detection can be attributed to a standard pattern classification problem, and the training sample costs have to be considered for the classifier modeling as the CFD numerical simulations and wind tunnel experiments of hypersonic inlets both cost time and money. To solve this problem, the CFD simulation of inlet is studied at first step, and the simulation results could provide the training data for pattern classification of hypersonic inlet start/unstart. Then the classifier modeling technology and maximum classifier utility theories are introduced to analyze the effect of training data cost on classifier utility. In conclusion, it is useful to introduce support vector machine algorithms to acquire the classifier model of hypersonic inlet start/unstart, and the minimum total cost of hypersonic inlet start/unstart classifier can be obtained by the maximum classifier utility theories.

Influence of starting powder milling on magnetic properties of Mn-Zn ferrite

Directory of Open Access Journals (Sweden)

Miodrag M. Milutinov

2017-06-01

Full Text Available In this paper, the influence of additional sieving and milling of starting industrial Mn-Zn powders on magnetic properties was investigated. The starting powder was milled for 60 minutes, followed by sieving through 325 and 400 meshes. The starting and milled powders were used to fabricate toroid shaped samples sintered at 1200°C for 2 hours. Structural parameters of the fabricated samples were analysed by X-ray diffraction and scanning electron microscopy. Complex permeability, core loss density, and hysteresis were measured using the modified watt-meter method. The complex permeability and hysteresis loop were modelled with a new model proposed in the paper. The core loss density was modelled with the Steinmetz empirical equation. The experimental results and calculations show the significance of the additional milling and sieving process on magnetic properties of Mn-Zn ferrite in the frequency range 0.1-10MHz. These processes increase the relative permeability about 3 times and decrease the core loss 4 times by milling of the starting powder.

Starting up the upstarts.

Science.gov (United States)

Greene, J

1997-12-20

Venture capitalists pour $1 billion a year into health care--and that investment may be the most overlooked indicator of new business opportunities. Signs show that companies focused on consolidation and cost-cutting are off the A list for risk capital. Instead, venture capitalists are targeting start-ups that save money on the front lines by truly managing care.

Start-up tests of Kashiwazakikariwa Nuclear Power Station Unit No.2 and No.5

International Nuclear Information System (INIS)

Fueki, Kensuke; Aoki, Shiro; Tanaka, Yasuhisa; Yahagi, Kimitoshi

1991-01-01

The Kashiwazakikariwa Nuclear Power Station Units No.5 and No.2 started commercial operation on April 10 and September 28 of 1990 respectively. As the result of the application of the First and Second LWR Improvement and Standardization Program, the plants were designed aiming at improvement of reliability, operation, and maintenance while maintaining safety. Construction of the plants took 6.5 to 7 years for completion, during which period the last 10 months were spent for the start up tests program. Start up tests were carried out under deliberate management to assure that the plants can operate safely and steadily at the prescribed operating points, and the schedules and tests item modifications adopted in Unit No.2 and No.5 were verified under the start up tests program. (author)

Design Methodology of Camshaft Driven Charge Valves for Pneumatic Engine Starts

Directory of Open Access Journals (Sweden)

Moser Michael M.

2015-01-01

Full Text Available Idling losses constitute a significant amount of the fuel consumption of internal combustion engines. Therefore, shutting down the engine during idling phases can improve its overall efficiency. For driver acceptance a fast restart of the engine must be guaranteed. A fast engine start can be performed using a powerful electric starter and an appropriate battery which are found in hybrid electric vehicles, for example. However, these devices involve additional cost and weight. An alternative method is to use a tank with pressurized air that can be injected directly into the cylinders to start the engine pneumatically. In this paper, pneumatic engine starts using camshaft driven charge valves are discussed. A general methodology for an air-optimal charge valve design is presented which can deal with various requirements. The proposed design methodology is based on a process model representing pneumatic engine operation. A design example for a two-cylinder engine is shown, and the resulting optimized pneumatic start is experimentally verified on a test bench engine. The engine’s idling speed of 1200 rpm can be reached within 350 ms for an initial pressure in the air tank of 10 bar. A detailed system analysis highlights the characteristics of the optimal design found.

Preliminary analyses for HTTR's start-up physics tests by Monte Carlo code MVP

International Nuclear Information System (INIS)

Nojiri, Naoki; Nakano, Masaaki; Ando, Hiroei; Fujimoto, Nozomu; Takeuchi, Mitsuo; Fujisaki, Shingo; Yamashita, Kiyonobu

1998-08-01

Analyses of start-up physics tests for High Temperature Engineering Test Reactor (HTTR) have been carried out by Monte Carlo code MVP based on continuous energy method. Heterogeneous core structures were modified precisely, such as the fuel compacts, fuel rods, coolant channels, burnable poisons, control rods, control rod insertion holes, reserved shutdown pellet insertion holes, gaps between graphite blocks, etc. Such precise modification of the core structures was difficult with diffusion calculation. From the analytical results, the followings were confirmed; The first criticality will be achieved around 16 fuel columns loaded. The reactivity at the first criticality can be controlled by only one control rod located at the center of the core with other fifteen control rods fully withdrawn. The excess reactivity, reactor shutdown margin and control rod criticality positions have been evaluated. These results were used for planning of the start-up physics tests. This report presents analyses of start-up physics tests for HTTR by MVP code. (author)

From Calculus to Wavelets: ANew Mathematical Technique

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 4. From Calculus to Wavelets: A New Mathematical Technique Wavelet Analysis Physical Properties. Gerald B Folland. General Article Volume 2 Issue 4 April 1997 pp 25-37 ...

From Calculus to Wavelets: ANew Mathematical Technique

Indian Academy of Sciences (India)

expansions have many theoretical and practical ..... them into a rigorous mathematical theory. Meyer con- structed an ... engineers for signal processing, Ingrid Daubechies con- ..... and its applications on a somewhat higher mathematical level.

Spectroscopic imaging of X-rays anew look

CERN Document Server

Heijne, Erik H M

2003-01-01

In recent hybrid imaging devices a segmented (50-100mum) semiconductor sensor matrix is matched to a separate readout chip made in some standard silicon CMOS technology. The large number of contacts are made by high-density bump bonding interconnect technology. Extended functionality with hundreds of transistors in each electronics cell can serve a variety of purposes. Fluctuations in the response of the sensor matrix can be compensated in real-time. A single photon processing circuit in each pixel can achieve spectroscopic imaging by energy measurement even at high rates. However, it is necessary to take into account the distribution of the signals over adjacent pixels. Another possibility is the discrimination by energy of photon conversions in stacked layers with increasing absorption.

The renaissance starts here

International Nuclear Information System (INIS)

Nedderman, John.

1997-01-01

The Asian Pacific Basin region has the highest rate of growth of anywhere in the world and its need for electricity is staggering. This is leading, noted a senior Korean official speaking at the 10th Pacific Basin Nuclear Conference, to a ''renaissance of nuclear power'' in Asia. Judging by the optimism in evidence at the conference, perhaps it has already started. (Author)

Impact of delaying school start time on adolescent sleep, mood, and behavior.

Science.gov (United States)

Owens, Judith A; Belon, Katherine; Moss, Patricia

2010-07-01

To examine the impact of a 30-minute delay in school start time on adolescents' sleep, mood, and behavior. Participants completed the online retrospective Sleep Habits Survey before and after a change in school start time. An independent high school in Rhode Island. Students (n = 201) in grades 9 through 12. Intervention Institution of a delay in school start time from 8 to 8:30 am. Sleep patterns and behavior, daytime sleepiness, mood, data from the Health Center, and absences/tardies. After the start time delay, mean school night sleep duration increased by 45 minutes, and average bedtime advanced by 18 minutes (95% confidence interval, 7-29 minutes [t(423) = 3.36; P students getting less than 7 hours of sleep decreased by 79.4%, and those reporting at least 8 hours of sleep increased from 16.4% to 54.7%. Students reported significantly more satisfaction with sleep and experienced improved motivation. Daytime sleepiness, fatigue, and depressed mood were all reduced. Most health-related variables, including Health Center visits for fatigue-related complaints, and class attendance also improved. A modest delay in school start time was associated with significant improvements in measures of adolescent alertness, mood, and health. The results of this study support the potential benefits of adjusting school schedules to adolescents' sleep needs, circadian rhythm, and developmental stage.

Control device for start-up of reactor depressurization system

International Nuclear Information System (INIS)

Suzuki, Hiroshi; Saito, Minoru; Oda, Shingo; Miura, Satoshi; Hashimoto, Koji; Tate, Hitoshi; Fujii, Kazunobu

1998-01-01

The present invention concerns are emergency reactor core cooling system (ECCS) of a BWR type reactor and provides a control device for start-up of an automatic depressurization system. Namely, the device has an object of preventing erroneous opening of a main steam escape safety value when testing a start-up signal circuit of an automatic depressurization system for testing the automatic depressurization system. A start-up signal circuit receives both signals of a reactor container pressure high signal and a reactor pressure vessel water level low signal and outputs an automatic start-up signal for compulsorily opening a main steam escape safety valve automatically. A test switch having a self-holding circuit is disposed to a central control chamber. A test signal circuit is disposed for preventing transfer of an erroneous start-up signal to the main steam escape safety valve due to a simulation signal during output test signals by the test switch. (I.S.)

When to Start Antiretroviral Therapy

Science.gov (United States)

... illnesses and coinfections Recent HIV infection Pregnancy All pregnant women with HIV should take HIV medicines to prevent mother-to- ... protect the health of the pregnant woman. All pregnant women with HIV should start taking HIV medicines as soon as ...

Start up testing for the secure automated fabrication line

International Nuclear Information System (INIS)

Gerber, E.W.; Benson, E.M.; Dahl, R.E.

1987-01-01

The secure automated fabrication (SAF) line is a remotely operated, liquid metal reactor fuel fabrication process being built by Westinghouse Hanford Company for the Department of Energy. All process and control equipment is installed and start up testing has been initiated. Start up testing is comprised of five phases, each incorporating higher degrees of equipment integration, automation, and remote control. Testing methodology for SAF line start up is described in this report

Getting started with Hazelcast

CERN Document Server

Johns, Mat

2013-01-01

Written as a step-by-step guide, Getting Started with Hazelcast will teach you all you need to know to make your application data scalable.This book is a great introduction for Java developers, software architects, or developers looking to enable scalable and agile data within their applications. You should have programming knowledge of Java and a general familiarity with concepts like data caching and clustering.

Influence of start-ups with fuel-oil on the operation of electrostatic precipitators in pulverised coal boilers

Energy Technology Data Exchange (ETDEWEB)

Navarrete, B.; Vilches, L.F.; Canadas, L.; Salvador, L. [University of Seville, Seville (Spain)

2004-04-01

This article describes the results of a series of tests carried out in a pilot fly ash electrostatic precipitation facility operating with real gases from a 550 MWe pulverized coal-fired power station. The main goal of these tests was to determine the effects of boiler start-ups on the performance of the electrostatic preciptator. The tests were carried out during start-ups of the power station boiler. All tests were carried out with the same fuel. An evaluation was made of the effects of the use of fuel-oil as auxillary fuel in start-ups and shut-downs of the boiler, and different electrostatic precipitators operation procedures were tested during start-ups and shut-downs. The results of the experiments made it possible to assess the relative importance of different variables on the possible deterioration of the efficiency of the precipitators. Also evaluated were operational modes that have demonstrated an improvement in the performance of the precipitators after the transient stage of these operations. As a result of this study, a number of important operational recommendations are made on boiler start-up and shut-down procedures.

Start-up phase assessment of a UASB-Septic tank system treating domestic septage

International Nuclear Information System (INIS)

Ali, M.; Al-Saed, R.; Mahmoud, N.

2007-01-01

About 65% of the annual domestic waste water in Palestine is currently collected in cesspits, where inadequate disposal might cause cumulative public health risks and annual environmental degradation. This research presents the preliminary results for the start-up period of a pilot-scale UASB-septic tank system treating domestic septage of Birzet town. Under different operational conditions, the performance of the pretreatment system for the removal of organic matter and nutrients was evaluated. Initial results showed that organic pollutants removal was mainly due to biophysical processes including sedimentation and microbial degradation. During start-up phase, the system attained removal efficiency for COD total of about 80% compared to removal for COD col, and COD dis of 71% and 43% respectively. Similarly, the continuous operation mode demonstrated that the system was quite effective in removing organic pollutants. Operational experience from the initial results revealed that seeding the USAB reactor with activated sludge during the start up period was not practical. Finally, the advantage of USAB-septic tank application appeared to be achievable if adequate system operation and control over a long monitoring period were maintained. (author)

40 CFR 1065.525 - Engine starting, restarting, shutdown, and optional repeating of void discrete modes.

Science.gov (United States)

2010-07-01

..., and optional repeating of void discrete modes. 1065.525 Section 1065.525 Protection of Environment... repeating of void discrete modes. (a) Start the engine using one of the following methods: (1) Start the... during one of the modes of a discrete-mode test, you may void the results only for that individual mode...

Impurity control and its impact upon start-up and transformer recharging in NET

International Nuclear Information System (INIS)

Harrison, M.F.A.

1985-01-01

Control of the release of impurities and their subsequent ingress and exhaust from tokamak plasmas has been the subject of intensive studies aimed at both the prediction of reactor burn condition and the interpretation of results from present experiments. Control concepts which are specific to current-initiation, current ramp-up and RF heating during start-up of a reactor such as NET have to date received little attention, according to the author. This paper presents an inductive start-up scenario which is typical of those presently being considered for NET. Shown are plasma configurations during start-up. Particularly significant issues are the advantages of forming the divertor configuration at the earliest practicable stage and the problems expected due to contamination of the limiter with divertor material

A novel induction motor starting method using superconduction

International Nuclear Information System (INIS)

Silva, F.B.B.; Orlando, M.T.D.; Fardin, J.F.; Simonetti, D.S.; Baldan, C.A.

2014-01-01

Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method

A novel induction motor starting method using superconduction

Energy Technology Data Exchange (ETDEWEB)

Silva, F.B.B., E-mail: flaviobarcelos@ifes.edu.br [Ifes – Federal Institute of Espírito Santo, Dept. of Industrial Automation, Serra, ES 29173087 (Brazil); UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Orlando, M.T.D. [UFES – Federal University of Espírito Santo, Dept. of Physics, Vitória, ES (Brazil); Fardin, J.F.; Simonetti, D.S. [UFES – Federal University of Espírito Santo, Dept. of Electrical Engineering, Vitória, ES (Brazil); Baldan, C.A. [EEL/USP – Engineering School from Lorena/University of São Paulo, SP (Brazil)

2014-12-15

Highlights: • Alternative method for starting up induction motor. • Based on using a high-temperature superconductor. • A prototype of the limiter was constructed with a 2G-YBCO tape. • Prototype was tested with a 55-kW industrial induction motor in a 440-V/60-Hz. • Offers reduced current waveform distortion compared to the soft starter method. - Abstract: In this paper, an alternative method for starting up induction motors is proposed, taking into account experimental measurements. The new starting current limitation method is based on using a high-temperature superconductor. A prototype of the superconducting starting current limiter was constructed with a commercially available second-generation high-temperature superconductor YBCO tape, and this was tested with a 55-kW industrial induction motor in a 440-V/60-Hz three-phase power grid. Performance evaluations of the superconducting limiter method (applied to startup of the induction motor) were performed and were compared with a direct-on-line starter and an electronic soft starter. In addition, a computational model was developed and used for electromagnetic torque analysis of the system. As significant characteristics, our method offers the ability to limit the starting current of the induction motor with greater electromagnetic torque, reduced current waveform distortion and therefore lower harmonic pollution during startup when compared to the soft starter method.

Early Start DENVER Model: A Meta - analysis

Directory of Open Access Journals (Sweden)

Jane P. Canoy

2015-11-01

Full Text Available Each child with Autism Spectrum Disorder has different symptoms, skills and types of impairment or disorder with other children. This is why the word “spectrum” is included in this disorder. Eapen, Crncec, and Walter, 2013 claimed that there was an emerging evidence that early interventions gives the greatest capacity of child’s development during their first years of life as “brain plasticity” are high during this period. With this, the only intervention program model for children as young as 18 months that has been validated in a randomized clinical trial is “Early Start Denver Model” (ESDM. This study aimed to determine the effectiveness of the outcome of “Early Start Denver Model” (ESDM towards young children with Autism Spectrum Disorders. This study made use of meta-analysis method. In this study, the researcher utilized studies related to “Early Start Denver Model (ESDM” which is published in a refereed journal which are all available online. There were five studies included which totals 149 children exposed to ESDM. To examine the “pooled effects” of ESDM in a variety of outcomes, a meta-analytic procedure was performed after the extraction of data of the concrete outcomes. Comprehensive Meta Analysis Version 3.3.070 was used to analyze the data.  The effectiveness of the outcome of “Early Start Denver Model” towards young children with Autism Spectrum Disorders (ASD highly depends on the intensity of intervention and the younger child age. This study would provide the basis in effectively implementing an early intervention to children with autism such as the “Early Start Denver Model” (ESDM that would show great outcome effects to those children that has “Autism Spectrum Disorder”.

CwicStart - a proof-of-concept client for the CEOSWGISS Integrated Catalog (CWIC)

Science.gov (United States)

Newman, D. J.; Mitchell, A. E.

2012-12-01

Keywords - Earth Science, data discovery, agile development, ruby on rails, catalog, OGC Audience - Earth Science application developers What is CwicStart CwicStart is a prototypical earth science data discovery web application designed, developed and hosted by NASA's Earth Observing System (EOS) Clearinghouse (ECHO). CwicStart searches the CEOS WGISS Integrated Catalog (CWIC) to provide users with dataset and granule level metadata from sources as diverse as NASA, NOAA, INPE and AOE. CwicStart demonstrates the ease of which it is possible to stand up a functioning client against the CWIC. From start to finish, CwicStart was designed, developed and deployed in one month. Built from OGC getCapabilities document of CWIC The CwicStart application takes the OGC getCapabilities (http://www.opengeospatial.org/standards/is) document describing CWIC, as it's starting point for providing a user interface suitable for interrogating CWIC. Consequently, it can allow the user to constrain their search by the following criteria, - Generic search terms - Spatial bounding box - Start date/time and end date/time - ISO-queryable key-value pairs User Interface inspired by Reverb ECHO's state-of-the-art earth science discovery tool, Reverb (http://reverb.echo.nasa.gov) was used as a guideline for the user interface components of CwicStart. It incorporates OpenLayers to provide point-and-click spatial constraint specification and calendar input for temporal constraints. Discovery involves two phases: dataset discovery and granule discovery with full pagination support for large results sets. CwicStart supports 'graceful degradation' of support for multiple browsers and accessibility requirements. Implemented in Ruby on Rails for Agile Development CwicStart is implemented in Ruby on Rails, a dynamic, rapid development language and environment that facilitates Agile development and is resilient to changing requirements. Using an Agile development methodology ECHO was able to stand up the

Head Start, 4 years After Completing the Program

Science.gov (United States)

Kim, Young-Joo

2013-01-01

This paper studies the effect of the Head Start program on children's achievements in reading and math tests during their first 4 years of schooling after completing the program. Using nationally representative data from the Early Childhood Longitudinal Study, I found large measurement error in the parental reports of Head Start attendance, which…

Anticipated simulation of Angra-1 start-up physical tests

International Nuclear Information System (INIS)

Fernandes, V.B.; Perrotta, J.A.; Silva Ipojuca, T. da; Ponzoni Filho, P.

1981-01-01

Some results foreseen by the Department of Nuclear Fuel (DCN. O) in Furnas for the measurements that will be realized during the start-up integrated tests for Angra-1 are presented. All the forecasting is based on a DCN.O proper correlation methodology, developed from basic physical principles, using computer codes developed by the authors or public computer codes adapted to this methodology. (E.G.) [pt

Summary revaluation of energetic start-up of the unit 1 of nuclear power plant Mochovce

International Nuclear Information System (INIS)

Sarvaic, I.; Miskolci, M.

1998-01-01

The document contents stage revaluation of energetic start-up of the unit 1 of nuclear power plant Mochovce. Test results of the stage of energetic start-up are summarized in the document, valuation of important systems and block devices as well as fulfilling the operation limits and conditions has been performed. On that base conclusions and recommendations for start-up the unit 2 and for commercial operation of the unit 1 are elaborated. The valuation has been elaborated by a scientific management for start-up nuclear power plant Mochovce of nuclear safety of nuclear power facilities. Scientific management for start-up of nuclear power plant Mochovce performed continuous valuation of individual power levels after ending of each individual level and it gave its valuation to energy power level with recommendations and conditions for further start-up process and operation. Scientific management finished its activity at the unit 1 of nuclear power plant Mochovce according to a statute of scientific management for start-up after successful completion of conclusive block run. Scientific management group was founded in February 1998 at nuclear power plant Mochovce. Its members are experts from Slovak, Czech, Russian and French organizations which are participating in power plant completion. Members are listed in a supplement No. 2

Effect of PWR Re-start ramp rate on pellet-cladding interactions

International Nuclear Information System (INIS)

Yagnik, S.K.; Chang, B.C.; Sunderland, D.J.

2005-01-01

To mitigate pellet-cladding interaction (PCI) leading to fuel rod failures, fuel suppliers specify reactor power ramp rate limitations during reactor start-up after an outage. Typical re-start ramp rates are restricted and range between 3-4% per hour of full reactor power above a threshold power level. Relaxation of threshold power and ramp rate restrictions has the potential to improve plant economics. The paper will compare known re-start power ascension procedures employed in the US, German, French and Korean PWRs after a refuelling outage. A technical basis for optimising power ascension procedures during reactor start-up can be developed using analytical modelling. The main objective of the modelling is to determine the potential for PCI failure for various combinations of threshold power levels and ramp rate levels. A key element of our analysis is to estimate the decrease in margin to cladding failure by ISCC based on a time-temperature-stress failure criterion fashioned Act a cumulative cladding damage index. The analysis approach and the cladding damage model will be described and the results from three case studies based on the FALCON fuel rod behaviour code will be reported. We conclude that the PCI behaviour is more affected by ramp rate and threshold power than by the fuel design and that the fuel power history is the most important parameter. (authors)

Effect of zero-valent iron and trivalent iron on UASB rapid start-up.

Science.gov (United States)

Wang, Jie; Fang, Hongyan; Jia, Hui; Yang, Guang; Gao, Fei; Liu, Wenbin

2018-01-01

In order to realize the rapid start-up of upflow anaerobic sludge blanket (UASB) reactor, the iron ion in different valence state was added to UASB. The results indicated that the start-up time of R3 (FeCl 3 ) was 48 h faster than that of R2 (zero-valent iron (ZVI)). It was because the FeCl 3 could rapidly promote granulation of sludge as a flocculant. However, ZVI released Fe 2+ through corrosion slowly, and then the Fe 2+ increased start-up speed by enhancing enzyme activity and enriching methanogens. In addition, the ZVI and FeCl 3 could promote hydrolysis acidification and strengthen the decomposition of long-chain fatty acids. The detection of iron ions showed that iron ions mainly existed in the sludge. Because the high concentration of Fe 2+ could inhibit anaerobic bacteria activity, excess Fe 3+ could be changed into iron hydroxide precipitation to hinder the mass transfer process of anaerobic bacteria under the alkaline condition. The FeCl 3 was suitable to be added at the initial stage of UASB start-up, and the ZVI was more fitted to be used in the middle stage of reactor start-up to improve the redox ability.

Coccidiosis and performance in broilers with anticoccidial medicated feed starting at different ages

Directory of Open Access Journals (Sweden)

Costa C.A.F.

2000-01-01

Full Text Available The effects of age, litter reutilization, and anticoccidial programs were studied in broilers. The oocyst counts increased with litter reutilization up to third use, and T1 (no anticoccidial drug over the entire 42-day-period and T4 (anticoccidial medication starting from the first day showed the highest counts. The scores for Eimeria acervulina increased up to third use of litter and declined by the fourth use. The scores for E. maxima increased from first to second litter use, and from this to third and fourth use. The scores for E. tenella increased from first and second litter use to third litter use, and declined on fourth use. With high coccidial contamination, as in third use litter, the anticoccidial medication starting from the 1st, 7th (T3 and 14th (T2 day of age presented similar results of lesion scores and average weight gain. When coccidial contamination was low or moderate, as in first, second and fourth use litter, the anticoccidial medication starting at 14 days of age tended to result in a better broiler performance. These data suggest that, with low coccidial challenge, as in broilers raised in first use litter and in farms with single bird age, the delayed anticoccidial medication may provide advantages over the full medication starting from the first day of age.

Simulation on the start-up of MED seawater desalination system coupled with nuclear heating reactor

International Nuclear Information System (INIS)

Ge Zhihua; Du Xiaoze; Yang Lijun; Yang Yongping; Wu Shaorong

2008-01-01

The mathematical control model for dynamic start-up process of the VTE-MED seawater desalination system was established employing the previous developed non-linear differential equations for system design and performance analysis. The influences on the start-up process of the operating parameters, such as the initial feed brine flow rate and the top brine temperature were analyzed. The relationships among the feed brine flow rate, the gained output ratio (GOR) and the start-up time were also investigated, which can be evidence to determine the optimal initial feed brine flow rate. The results also indicate that the system can consume the total heat rating generated by the low temperature nuclear heating reactor (LT-NHR) even at the most initial start-up stage, implying the present desalination system has excellent coupling characteristics with the LT-NHR. With necessary experiments verifications, the start-up control model developed in this paper can be the theoretical base for the analysis of dynamic performances of the seawater desalination system

Applying behavioral insights to delay school start times.

Science.gov (United States)

Kohl Malone, Susan; Ziporyn, Terra; Buttenheim, Alison M

2017-12-01

Healthy People 2020 established a national objective to increase the proportion of 9th-to-12th-grade students reporting sufficient sleep. A salient approach for achieving this objective is to delay middle and high school start times. Despite decades of research supporting the benefits of delayed school start times on adolescent sleep, health, and well-being, progress has been slow. Accelerating progress will require new approaches incorporating strategies that influence how school policy decisions are made. In this commentary, we introduce four strategies that influence decision-making processes and demonstrate how they can be applied to efforts aimed at changing school start time policies. Copyright © 2017 National Sleep Foundation. All rights reserved.

Ten steps to get started in Genome Assembly and Annotation

Science.gov (United States)

Dominguez Del Angel, Victoria; Hjerde, Erik; Sterck, Lieven; Capella-Gutierrez, Salvadors; Notredame, Cederic; Vinnere Pettersson, Olga; Amselem, Joelle; Bouri, Laurent; Bocs, Stephanie; Klopp, Christophe; Gibrat, Jean-Francois; Vlasova, Anna; Leskosek, Brane L.; Soler, Lucile; Binzer-Panchal, Mahesh; Lantz, Henrik

2018-01-01

As a part of the ELIXIR-EXCELERATE efforts in capacity building, we present here 10 steps to facilitate researchers getting started in genome assembly and genome annotation. The guidelines given are broadly applicable, intended to be stable over time, and cover all aspects from start to finish of a general assembly and annotation project. Intrinsic properties of genomes are discussed, as is the importance of using high quality DNA. Different sequencing technologies and generally applicable workflows for genome assembly are also detailed. We cover structural and functional annotation and encourage readers to also annotate transposable elements, something that is often omitted from annotation workflows. The importance of data management is stressed, and we give advice on where to submit data and how to make your results Findable, Accessible, Interoperable, and Reusable (FAIR). PMID:29568489

IMMEDIATE EFFECTS OF DEEP TRUNK MUSCLE TRAINING ON SWIMMING START PERFORMANCE.

Science.gov (United States)

Iizuka, Satoshi; Imai, Atsushi; Koizumi, Keisuke; Okuno, Keisuke; Kaneoka, Koji

2016-12-01

In recent years, deep trunk muscle training has been adopted in various sports, including swimming. This is performed both in everyday training and as part of the warm-up routine before competitive races. It is suggested that trunk stabilization exercises are effective in preventing injury, and aid in improving performance. However, conclusive evidence of the same is yet to be obtained. The time of start phase of swimming is a factor that can significantly influence competition performance in a swimming race. If trunk stabilization exercises can provide instantaneous trunk stability, it is expected that they will lead to performance improvements in the start phase of swimming. The purpose of this study was to investigate the immediate effect of trunk stabilization exercises on the start phase in swimming. Intervention study. Nine elite male swimmers (mean age 20.2 ± 1.0 years; height 174.4 ± 3.5 cm; weight 68.9 ± 4.1 kg) performed the swimming start movement. The measurement variables studied included flying distance, and the time and velocity of subjects at hands' entry and on reaching five meters. Measurements were taken in trials immediately before and after the trunk stabilization exercises. A comparison between pre- and post-exercise measurements was assessed. The time to reach five meters (T 5m ) decreased significantly after trunk stabilization exercises, by 0.019 s (p = 0.02). Velocity at entry (V entry ) did not demonstrate significant change, while velocity at five meters (V 5m ) increased significantly after the exercises (p = 0.023). In addition, the speed reduction rate calculated from V entry and V 5m significantly decreased by 5.17% after the intervention (p = 0.036). Trunk stabilization exercises may help reduce the time from start to five meters in the start phase in swimming. The results support the hypothesis that these exercises may improve swimming performance. Level 3b.

Random-start ovarian stimulation in women desiring elective cryopreservation of oocytes.

Science.gov (United States)

Pereira, Nigel; Voskuilen-Gonzalez, Anna; Hancock, Kolbe; Lekovich, Jovana P; Schattman, Glenn L; Rosenwaks, Zev

2017-10-01

The current study investigates the utility of random-start ovarian stimulation in women desiring elective oocyte cryopreservation. Women in the study cohort underwent random-start ovarian stimulation, and were subdivided based on the phase of the menstrual cycle that ovarian stimulation began, i.e. early follicular, late follicular or luteal phase. Women undergoing conventional cycle day (CD) 2/3 ovarian stimulation start were controls. A total of 1302 women were included - 859 (66.0%) conventional CD 2/3, 342 (26.3%) early follicular, 42 (3.2%) late follicular and 59 (4.5%) luteal ovarian stimulation starts. There was no difference in the demographics or baseline ovarian stimulation characteristics. The duration of ovarian stimulation (11 versus 9 days; P start group. The number of total and MII oocytes in the control and random-start groups was similar. A non-significant trend towards increased cycle cancellation was noted in the late follicular start group (7.1%). Study findings indicate the number of total and MII oocytes derived from random-start protocols initiated during any phase of the menstrual cycle is similar to conventional CD 2/3 ovarian stimulation start protocols in women desiring elective oocyte cryopreservation. Copyright © 2017 Reproductive Healthcare Ltd. Published by Elsevier Ltd. All rights reserved.

Backstroke start kinematic and kinetic changes due to different feet positioning.

Science.gov (United States)

de Jesus, Karla; de Jesus, Kelly; Figueiredo, Pedro; Gonçalves, Pedro; Pereira, Suzana Matheus; Vilas-Boas, João Paulo; Fernandes, Ricardo Jorge

2013-01-01

The backstroke swimming start international rules changed in 2005. This study compared two backstroke start variants, both with feet parallel to each other but in complete immersion and emersion. Six elite swimmers performed two sets of 4 maximal 15 m bouts, each set using one of the variants. The starts were videotaped in the sagittal plane with two cameras, providing bi-dimensional dual-media kinematic evaluation, and an underwater force plate and a handgrip instrumented with a load cell collected kinetic data. Backstroke start with feet immerged displayed greater centre-of-mass horizontal starting position, centre-of-mass horizontal velocity at hands-off and take-off angle. Backstroke start with feet emerged showed greater wall contact time, centre-of-mass horizontal and downward vertical velocity at take-off, lower limbs horizontal impulse, and centre-of-mass downward vertical velocity during flight phase. Backstroke start with feet immerged and emerged displayed similar centre-of-mass horizontal water reach, back arc angle and 5 m starting time. Irrespective of the swimmer's feet positioning, coaches should emphasise each variant's mechanical advantages during the wall contact phases. Furthermore, the maintenance of those advantages throughout the flight should be stressed for better backstroke start performance.

North Carolina's Smart Start Initiative: 1994-95 Annual Evaluation Report.

Science.gov (United States)

North Carolina Univ., Chapel Hill. Frank Porter Graham Center.

Smart Start is North Carolina's partnership between state government and local leaders, service providers, and families to better serve children under six years and their families to ensure that all children start school healthy and prepared to succeed. Local Smart Start partnerships spent much of their first year formulating long-term plans,…

Later School Start Times: What Informs Parent Support or Opposition?

Science.gov (United States)

Dunietz, Galit Levi; Matos-Moreno, Amilcar; Singer, Dianne C; Davis, Matthew M; O'Brien, Louise M; Chervin, Ronald D

2017-07-15

To investigate parental knowledge about adolescent sleep needs, and other beliefs that may inform their support for or objection to later school start times. In 2014, we conducted a cross-sectional, Internet-based survey of a nationally representative sample of parents as part of the C.S. Mott Children's Hospital National Poll on Children's Health. Parents with teens aged 13-17 years reported their children's sleep patterns and school schedules, and whether the parents supported later school start times (8:30 am or later). Responses associated with parental support of later school start times were examined with logistic regression analysis. Overall, 88% of parents reported school start times before 8:30 am, and served as the analysis sample (n = 554). In this group, 51% expressed support for later school start times. Support was associated with current school start times before 7:30 am (odds ratio [OR] = 3.1 [95% confidence interval (CI) 1.2, 8.4]); parental opinion that their teen's current school start time was "too early" (OR = 3.8 [1.8, 7.8]); and agreement with American Academy of Pediatrics recommendations about school start times (OR = 4.7 [2.2, 10.1]). Support also was associated with anticipation of improved school performance (OR = 3.0 [1.5, 5.9]) or increased sleep duration (OR = 4.0 [1.8, 8.9]) with later school start times. Conversely, parents who anticipated too little time for after-school activities (OR = 0.5 [0.3, 0.9]) and need for different transportation plans (OR = 0.5 [0.2, 0.9]) were often less supportive. Parental education about healthy sleep needs and anticipated health benefits may increase their support for later school start times. Educational efforts should also publicize the positive experiences of communities that have made this transition, with regard to limited adverse effect on after-school activity schedules and transportation. © 2017 American Academy of Sleep Medicine

Head Start Impact Study. Final Report. Executive Summary

Science.gov (United States)

Puma, Michael; Bell, Stephen; Cook, Ronna; Heid, Camilla; Shapiro, Gary; Broene, Pam; Jenkins, Frank; Fletcher, Philip; Quinn, Liz; Friedman, Janet; Ciarico, Janet; Rohacek, Monica; Adams, Gina; Spier, Elizabeth

2010-01-01

This report summarizes the findings from a study on the impacts of Head Start on children and families during the children's preschool, kindergarten, and 1st grade years. Its study goals were to: (1) Determine the impact of Head Start on children's school readiness, and on parental practices that support children's development; and to (2)…

Identification of the translational start site of codon-optimized mCherry in Mycobacterium tuberculosis

OpenAIRE

Carroll, Paul; Muwanguzi-Karugaba, Julian; Melief, Eduard; Files, Megan; Parish, Tanya

2014-01-01

Background Fluorescent proteins are used widely as reporter genes in many organisms. We previously codon-optimized mCherry for Mycobacterium tuberculosis and generated expression constructs with high level expression in mycobacteria with multiple uses in vitro and in vivo. However, little is known about the expression of fluorescent proteins in mycobacteria and the translational start codon for mCherry has not been experimentally determined. Results We determined the translational start site ...

Supporting Optimal Child Development through Early Head Start and Head Start Programs: Reflections on Secondary Data Analyses of FACES and EHSREP

Science.gov (United States)

Chazan-Cohen, Rachel; Halle, Tamara G.; Barton, Lauren R.; Winsler, Adam

2012-01-01

We are delighted to reflect on the 10 papers highlighted in this important special issue of "Early Childhood Research Quarterly" devoted to recent secondary data analyses of the FACES and EHSREP datasets. First, we provide some background on Head Start research and give an overview of the large-scale Head Start and Early Head Start…

Study on ECH-assisted start-up using trapped particle configuration in KSTAR and application to ITER

Science.gov (United States)

Lee, Jeongwon; Kim, Jayhyun; An, YoungHwa; Yoo, Min-Gu; Hwang, Y. S.; Na, Yong-Su

2017-12-01

ECH-assisted start-up using trapped particle configuration (TPC) is firstly studied in a superconducting, conventional tokamak, KSTAR. First, improved and efficient start-up using TPC than conventional field null configuration (FNC) is achieved by enhanced pre-ionization plasma quality. TPC shows the broader operation window in terms of the poloidal field quality and the deuterium prefill pressure than that of FNC. Surprisingly the particle trapping enhances the plasma start-up performance even with much lower particle trapping ratio than that of spherical torus. Reliability of TPC with low trapping ratio is investigated by 0D plasma evolution code, TECHP0D. Second, the characteristics of TPC start-up are explored with experiments and modellings. Two kind of start-up failure conditions are identified by the magnetic pitch and prefill pressure scan experiments: (i) low ionization rate; and (ii) low density condition. These experimental observation has consistency with TECHP0D modeling result. Finally, reliable ITER-relevant low toroidal electric field start-up using TPC is achieved with drastically improved success rate of start-up in KSTAR. In this experiments, validity of the ITER-like toroidally inclined ECH/ECCD injection is also expected. Time dependent ITER start-up scenario using TPC is proposed and the superiority of it than FNC is discussed.

Cold start dynamics and temperature sliding observer design of an automotive SOFC APU

Science.gov (United States)

Lin, Po-Hsu; Hong, Che-Wun

This paper presents a dynamic model for studying the cold start dynamics and observer design of an auxiliary power unit (APU) for automotive applications. The APU is embedded with a solid oxide fuel cell (SOFC) stack which is a quiet and pollutant-free electric generator; however, it suffers from slow start problem from ambient conditions. The SOFC APU system equips with an after-burner to accelerate the start-up transient in this research. The combustion chamber burns the residual fuel (and air) left from the SOFC to raise the exhaust temperature to preheat the SOFC stack through an energy recovery unit. Since thermal effect is the dominant factor that influences the SOFC transient and steady performance, a nonlinear real-time sliding observer for stack temperature was implemented into the system dynamics to monitor the temperature variation for future controller design. The simulation results show that a 100 W APU system in this research takes about 2 min (in theory) for start-up without considering the thermal limitation of the cell fracture.

The Role of Classroom Quality in Explaining Head Start Impacts

Science.gov (United States)

Connors, Maia C.; Friedman-Krauss, Allison H.; Morris, Pamela A.; Page, Lindsay C.; Feller, Avi

2014-01-01

This study seeks to answer the following question: Are impacts on Head Start classroom quality associated with impacts of Head Start on children's learning and development? This study employs a variety of descriptive and quasi-experimental methods to explore the role of classroom quality as a mediator or mechanism of Head Start impacts. This…

Enhancing Early Childhood Outcomes: Connecting Child Welfare and Head Start

Science.gov (United States)

McCrae, Julie S.; Brown, Samantha M.; Yang, Jessica; Groneman, Sheila

2016-01-01

Head Start is a preschool program for families with low incomes and nearly 85% of child welfare-involved families are low-income, yet little is known about Head Start and child welfare collaboration. This study uses data from 28 Head Start directors to describe collaboration facilitators and barriers, and collaborative mechanisms in place. The…

From Jam to Start-up

DEFF Research Database (Denmark)

Bering Kjæhr, Emil; Lyngbye Hvid Jensen, Jane; Schoenau-Fog, Henrik

2015-01-01

the foundation for new start-up companies. There are, however, an even larger group of very creative and innovative games and artifacts with great potential that go unpublished. This potentially leads to a loss of entrepreneurial opportunities and ultimately the jobs and careers such games could have fostered...

Head Start Center Design Guide.

Science.gov (United States)

Administration for Children, Youth, and Families (DHHS), Washington, DC. Head Start Bureau.

This guide contains suggested criteria for planning, designing, and renovating Head Start centers so that they are safe, child-oriented, developmentally appropriate, beautiful, environmentally sensitive, and functional. The content is based on the U.S. General Services Administration's Child Care Center Design Guide, PBS-P140, which was intended…

School start times and teenage driver motor vehicle crashes.

Science.gov (United States)

Foss, Robert D; Smith, Richard L; O'Brien, Natalie P

2018-04-26

Shifting school start times to 8:30 am or later has been found to improve academic performance and reduce behavior problems. Limited research suggests this may also reduce adolescent driver motor vehicle crashes. A change in the school start time from 7:30 am to 8:45 am for all public high schools in one North Carolina county presented the opportunity to address this question with greater methodologic rigor. We conducted ARIMA interrupted time-series analyses to examine motor vehicle crash rates of high school age drivers in the intervention county and 3 similar comparison counties with comparable urban-rural population distribution. To focus on crashes most likely to be affected, we limited analysis to crashes involving 16- & 17-year-old drivers occurring on days when school was in session. In the intervention county, there was a 14% downward shift in the time-series following the 75 min delay in school start times (p = .076). There was no change approaching statistical significance in any of the other three counties. Further analysis indicated marked, statistically significant shifts in hourly crash rates in the intervention county, reflecting effects of the change in school start time on young driver exposure. Crashes from 7 to 7:59 am decreased sharply (-25%, p = .008), but increased similarly from 8 to 8:59 am (21%, p = .004). Crashes from 2 to 2:59 pm declined dramatically (-48%, p = .000), then increased to a lesser degree from 3 to 3:59 pm (32%, p = .024) and non-significantly from 4 to 4:59 (19%, p = .102). There was no meaningful change in early morning or nighttime crashes, when drowsiness-induced crashes might have been expected to be most common. The small decrease in crashes among high school age drivers following the shift in school start time is consistent with the findings of other studies of teen driver crashes and school start times. All these studies, including the present one, have limitations, but the similar

Getting started with Simulink

CERN Document Server

Zamboni, Luca

2013-01-01

This practical and easy-to-understand learning tutorial is one big exciting exercise for students and engineers that are always short on their schedules and want to regain some lost time with the help of Simulink.This book is aimed at students and engineers who need a quick start with Simulink. Though it's not required in order to understand how Simulink works, knowledge of physics will help the reader to understand the exercises described.

Getting started with JUCE

CERN Document Server

Robinson, Martin

2013-01-01

his book is a fast-paced, practical guide full of step-by-step examples which are easy to follow and implement.This book is for programmers with a basic grasp of C++. The examples start at a basic level, making few assumptions beyond fundamental C++ concepts. Those without any experience with C++ should be able to follow and construct the examples, although you may need further support to understand the fundamental concepts.

Starting infants on antiretroviral therapy | Clayden | Southern African ...

African Journals Online (AJOL)

5 years or more, that most start at a late stage of the disease, and that mortality in the first few months of treatment remains high.5,6 A recent study shows that starting treatment in early infancy can be lifesaving, and this has informed revisions in World Health Organization (WHO) guidelines7,8 (see WHO 'Dear Health Care ...

Start-up and bacterial community compositions of partial nitrification in moving bed biofilm reactor.

Science.gov (United States)

Liu, Tao; Mao, Yan-Jun; Shi, Yan-Ping; Quan, Xie

2017-03-01

Partial nitrification (PN) has been considered as one of the promising processes for pretreatment of ammonium-rich wastewater. In this study, a kind of novel carriers with enhanced hydrophilicity and electrophilicity was implemented in a moving bed biofilm reactor (MBBR) to start up PN process. Results indicated that biofilm formation rate was higher on modified carriers. In comparison with the reactor filled with traditional carriers (start-up period of 21 days), it took only 14 days to start up PN successfully with ammonia removal efficiency and nitrite accumulation rate of 90 and 91%, respectively, in the reactor filled with modified carriers. Evident changes of spatial distributions and community structures had been detected during the start-up. Free-floating cells existed in planktonic sludge, while these microorganisms trended to form flocs in the biofilm. High-throughput pyrosequencing results indicated that Nitrosomonas was the predominant ammonia-oxidizing bacterium (AOB) in the PN system, while Comamonas might also play a vital role for nitrogen oxidation. Additionally, some other bacteria such as Ferruginibacter, Ottowia, Saprospiraceae, and Rhizobacter were selected to establish stable footholds. This study would be potentially significant for better understanding the microbial features and developing efficient strategies accordingly for MBBR-based PN operation.

Self-starting aerodynamics analysis of vertical axis wind turbine

Directory of Open Access Journals (Sweden)

Jianyang Zhu

2015-12-01

Full Text Available Vertical axis wind turbine is a special type of wind-force electric generator which is capable of working in the complicated wind environment. The self-starting aerodynamics is one of the most important considerations for this kind of turbine. This article aims at providing a systematic synthesis on the self-starting aerodynamic characteristics of vertical axis wind turbine based on the numerical analysis approach. First, the physical model of vertical axis wind turbine and its parameter definitions are presented. Secondary, the interaction model between the vertical axis wind turbine and fluid is developed by using the weak coupling approach; the numerical data of this model are then compared with the wind tunnel experimental data to show its feasibility. Third, the effects of solidity and fixed pitch angle on the self-starting aerodynamic characteristics of the vertical axis wind turbine are analyzed systematically. Finally, the quantification effects of the solidity and fixed pitch angle on the self-starting performance of the turbine can be obtained. The analysis in this study will provide straightforward physical insight into the self-starting aerodynamic characteristics of vertical axis wind turbine.

Preliminary analyses for HTTR`s start-up physics tests by Monte Carlo code MVP

Energy Technology Data Exchange (ETDEWEB)

Nojiri, Naoki [Science and Technology Agency, Tokyo (Japan); Nakano, Masaaki; Ando, Hiroei; Fujimoto, Nozomu; Takeuchi, Mitsuo; Fujisaki, Shingo; Yamashita, Kiyonobu

1998-08-01

Analyses of start-up physics tests for High Temperature Engineering Test Reactor (HTTR) have been carried out by Monte Carlo code MVP based on continuous energy method. Heterogeneous core structures were modified precisely, such as the fuel compacts, fuel rods, coolant channels, burnable poisons, control rods, control rod insertion holes, reserved shutdown pellet insertion holes, gaps between graphite blocks, etc. Such precise modification of the core structures was difficult with diffusion calculation. From the analytical results, the followings were confirmed; The first criticality will be achieved around 16 fuel columns loaded. The reactivity at the first criticality can be controlled by only one control rod located at the center of the core with other fifteen control rods fully withdrawn. The excess reactivity, reactor shutdown margin and control rod criticality positions have been evaluated. These results were used for planning of the start-up physics tests. This report presents analyses of start-up physics tests for HTTR by MVP code. (author)

Soft start technique for diesel generator sets

International Nuclear Information System (INIS)

Fredlund, Lars

1986-01-01

A diesel motor in a nuclear power plant should be of a well-proven design. It is designed for long periods of trouble-free duty, but not for the frequent and rapid test starts called for by the technical specifications. In order to decrease the dynamic forces and thermal stresses, a soft-start scheme has been implemented. By limiting the fuel injection the diesel generator will reach full speed in appr. 30 seconds. The fuel limiter is a pneumatic cylinder which mechanically limits the travel of the terminal shaft of the governor. (author)

Soft start technique for diesel generator sets

Energy Technology Data Exchange (ETDEWEB)

Fredlund, Lars [Swedish State Power Board, Ringhals Nuclear Power Plant, S-430 22, Vaeroebacka (Sweden)

1986-02-15

A diesel motor in a nuclear power plant should be of a well-proven design. It is designed for long periods of trouble-free duty, but not for the frequent and rapid test starts called for by the technical specifications. In order to decrease the dynamic forces and thermal stresses, a soft-start scheme has been implemented. By limiting the fuel injection the diesel generator will reach full speed in appr. 30 seconds. The fuel limiter is a pneumatic cylinder which mechanically limits the travel of the terminal shaft of the governor. (author)

Class start times, sleep, and academic performance in college: a path analysis.

Science.gov (United States)

Onyper, Serge V; Thacher, Pamela V; Gilbert, Jack W; Gradess, Samuel G

2012-04-01

Path analysis was used to examine the relationship between class start times, sleep, circadian preference, and academic performance in college-aged adults. Consistent with observations in middle and high school students, college students with later class start times slept longer, experienced less daytime sleepiness, and were less likely to miss class. Chronotype was an important moderator of sleep schedules and daytime functioning; those with morning preference went to bed and woke up earlier and functioned better throughout the day. The benefits of taking later classes did not extend to academic performance, however; grades were somewhat lower in students with predominantly late class schedules. Furthermore, students taking later classes were at greater risk for increased alcohol consumption, and among all the factors affecting academic performance, alcohol misuse exerted the strongest effect. Thus, these results indicate that later class start times in college, while allowing for more sleep, also increase the likelihood of alcohol misuse, ultimately impeding academic success.

Software for physical start-up console

International Nuclear Information System (INIS)

Arbet, L.; Suchy, R.

1991-01-01

The physical start-up console comprises an PC AT-based control unit equipped with an 80386 processor, and information input/output units. The basic functions to be fulfilled by the control unit software include data acquisition related to the following parameters: neutron physics properties of the reactor core (neutron fluxes recorded by ionization chambers and reactivity recorded by a digital reactimeter), positions of the reactor core control elements (by the digital position meter) and reactor core control measurements, and technological quantities requisite for evaluating physical start-up tests. The measured and calculated data are shown on the control unit display. The setup of the data acquisition system and of user programs is dealt with, and characteristics of the user processes are briefly described. (Z.S.)

Starting apparatus for internal combustion engines

Science.gov (United States)

Dyches, Gregory M.; Dudar, Aed M.

1997-01-01

An internal combustion engine starting apparatus uses a signal from a curt sensor to determine when the engine is energized and the starter motor should be de-energized. One embodiment comprises a transmitter, receiver, computer processing unit, current sensor and relays to energize a starter motor and subsequently de-energize the same when the engine is running. Another embodiment comprises a switch, current transducer, low-pass filter, gain/comparator, relay and a plurality of switches to energize and de-energize a starter motor. Both embodiments contain an indicator lamp or speaker which alerts an operator as to whether a successful engine start has been achieved. Both embodiments also contain circuitry to protect the starter and to de-energize the engine.

Comparative structural analysis of lipid binding START domains.

Directory of Open Access Journals (Sweden)

Ann-Gerd Thorsell

Full Text Available Steroidogenic acute regulatory (StAR protein related lipid transfer (START domains are small globular modules that form a cavity where lipids and lipid hormones bind. These domains can transport ligands to facilitate lipid exchange between biological membranes, and they have been postulated to modulate the activity of other domains of the protein in response to ligand binding. More than a dozen human genes encode START domains, and several of them are implicated in a disease.We report crystal structures of the human STARD1, STARD5, STARD13 and STARD14 lipid transfer domains. These represent four of the six functional classes of START domains.Sequence alignments based on these and previously reported crystal structures define the structural determinants of human START domains, both those related to structural framework and those involved in ligand specificity.This article can also be viewed as an enhanced version in which the text of the article is integrated with interactive 3D representations and animated transitions. Please note that a web plugin is required to access this enhanced functionality. Instructions for the installation and use of the web plugin are available in Text S1.

Decreasing stunting, anemia, and vitamin A deficiency in Peru: results of the Good Start in Life Program.

Science.gov (United States)

Lechtig, Aarón; Cornale, Guido; Ugaz, María Elena; Arias, Lena

2009-03-01

The rates of stunting, iron-deficiency anemia, and vitamin A deficiency in Peru are among the highest in South America. There is little scaled-up experience on how to solve these problems countrywide. To evaluate the Good Start in Life Program during the period from 2000 to 2004. Data on weight, height, hemoglobin, serum retinol, urinary iodine, and age were obtained from children under 3 years of age during two transverse surveys in 2000 and 2004. In 2004, the program covered 75,000 children, 35,000 mothers, and 1 million inhabitants from 223 poor communities. The rate of stunting decreased from 54.1% to 36.9%, the rate of iron-deficiency anemia decreased from 76.0% to 52.3%, and the rate of vitamin A deficiency decreased from 30.4% to 5.3% (p anemia, and vitamin A deficiency at the national scale in Peru and many other countries.

Plyometric Long Jump Training With Progressive Loading Improves Kinetic and Kinematic Swimming Start Parameters.

Science.gov (United States)

Rebutini, Vanessa Z; Pereira, Gleber; Bohrer, Roberta C D; Ugrinowitsch, Carlos; Rodacki, André L F

2016-09-01

Rebutini, VZ, Pereira, G, Bohrer, RCD, Ugrinowitsch, C, and Rodacki, ALF. Plyometric long jump training with progressive loading improves kinetic and kinematic swimming start parameters. J Strength Cond Res 30(9): 2392-2398, 2016-This study was aimed to determine the effects of a plyometric long jump training program on torque around the lower limb joints and kinetic and kinematics parameters during the swimming jump start. Ten swimmers performed 3 identical assessment sessions, measuring hip and knee muscle extensors during maximal voluntary isometric contraction and kinetic and kinematics parameters during the swimming jump start, at 3 instants: INI (2 weeks before the training program, control period), PRE (2 weeks after INI measurements), and POST (24-48 hours after 9 weeks of training). There were no significant changes from INI to PRE measurements. However, the peak torque and rate of torque development increased significantly from PRE to POST measurements for both hip (47 and 108%) and knee (24 and 41%) joints. There were significant improvements to the horizontal force (7%), impulse (9%), and angle of resultant force (19%). In addition, there were significant improvements to the center of mass displacement (5%), horizontal takeoff velocity (16%), horizontal velocity at water entrance (22%), and peak angle velocity for the knee (15%) and hip joints (16%). Therefore, the plyometric long jump training protocol was effective to enhance torque around the lower limb joints and to control the resultant vector direction, to increase the swimming jump start performance. These findings suggest that coaches should use long jump training instead of vertical jump training to improve swimming start performance.

Experimental study of starting plumes simulating cumulus cloud flows in the atmosphere

Science.gov (United States)

Subrahmanyam, Duvvuri; Sreenivas, K. R.; Bhat, G. S.; Diwan, S. S.; Narasimha, Roddam

2009-11-01

Turbulent jets and plumes subjected to off-source volumetric heating have been studied experimentally and numerically by Narasimha and co-workers and others over the past two decades. The off-source heating attempts to simulate the latent heat release that occurs in cumulus clouds on condensation of water vapour. This heat release plays a crucial role in determining the overall cloud shape among other things. Previous studies investigated steady state jets and plumes that had attained similarity upstream of heat injection. A better understanding and appreciation of the fluid dynamics of cumulus clouds should be possible by study of starting plumes. Experiments have been set up at JNCASR (Bangalore) using experimental techniques developed previously but incorporating various improvements. Till date, experiments have been performed on plumes at Re of 1000 and 2250, with three different heating levels in each case. Axial sections of the flow have been studied using standard PLIF techniques. The flow visualization provides us with data on the temporal evolution of the starting plume. It is observed that the broad nature of the effect of off-source heating on the starting plumes is generally consistent with the results obtained previously on steady state flows. More complete results and a critical discussion will be presented at the upcoming meeting.

Optimal Rotor Design of Line Start Permanent Magnet Synchronous Motor by Genetic Algorithm

Directory of Open Access Journals (Sweden)

Bui Minh Dinh

2017-07-01

Full Text Available Line start permanent magnet synchronous motor (LSPMSM is one of the highest efficiency motors due to no rotor copper loss at synchronous speed and self-starting. LSPMSM has torque characteristics of both induction motor IM and Permanent Magnet Synchronous Motor-PMSM. Using Genetic Algorithm (GA for balancing magnetic cost and for copper loss minimization, the magnetic sizes and geometry parameter of stator and rotor are found and manufactured for industrial evaluation. This article is also taking account practical manufacturing factors to minimize mass production cost. In order to maximize efficiency, an optimal design method of cage-bars and magnet shape has to be considered. The geometry parameters of stator and rotor can be obtained by an analytical model method and validated by FEM simulation. This paper presents the optimal rotor design of a three-phase line-start permanent magnet motor (LSPM considering the starting torque and efficiency. To consider nonlinear characteristics, the design process is comprised of the FEM and analytical method. During this study, permanent-magnets and cage bars were designed using the magnetic equivalent circuit method and the barriers that control all magnetic flux were designed using the FEM, and the tradeoff of starting torque and efficiency is controlled by weight function in Taguchi method simulation. Finally, some practical results have been obtained and analyzed based on a LSPMSM test bench.

A Robotic Fish to Emulate the Fast-Start

Science.gov (United States)

Currier, Todd; Ma, Ganzhong; Modarres-Sadeghi, Yahya

2017-11-01

An experimental study is conducted on a robotic fish designed to emulate the fast-start response. The fish body is constructed of 3D printed ribs and a light spring steel spine. The body is actuated using a series of pressured pistons. A total of four pistons are supplied with pressure through lightweight high pressure service lines. The source of pressure is carbon dioxide with a 700 psi peak operating pressure resulting in a body response that can cycle a c-start maneuver in milliseconds. The motion of the fish is precisely controlled through the use of solenoids with a control signal produced by a programmable microprocessor. The fish is constrained in all translational degrees of freedom but allowed to rotate about a vertical axis. The influence of the point of rotation is studied with different mounting points along the length of the head of the fish. The forces are measured in two perpendicular in-plane directions. A high speed camera is used to capture the response of the fish and the corresponding flow around it. Comparison is made with the kinematics observed in live fish.

USABC Development of 12 Volt Battery for Start-Stop Application: Preprint

Energy Technology Data Exchange (ETDEWEB)

Tataria, H.; Gross, O.; Bae, C.; Cunningham, B.; Barnes, J. A.; Deppe, J.; Neubauer, J.

2015-02-01

Global automakers are accelerating the development of fuel efficient vehicles, as a part of meeting regional regulatory CO2 emissions requirements. The micro hybrid vehicles with auto start-stop functionality are considered economical solutions for the stringent European regulations. Flooded lead acid batteries were initially considered the most economical solution for idle-stop systems. However, the dynamic charge acceptance (DCA) at lower state-of-charge (SOC) was limiting the life of the batteries. While improved lead-acid batteries with AGM and VRLA features have improved battery longevity, they do not last the life of the vehicle. The United States Advanced Battery Consortium (or USABC, a consortium of GM, Ford, and Chrysler) analyzed energy storage needs for a micro hybrid automobile with start-stop capability, and with a single power source. USABC has analyzed the start-stop behaviors of many drivers and has developed the requirements for the start-stop batteries (Table 3). The testing procedures to validate the performance and longevity were standardized and published. The guideline for the cost estimates calculations have also been provided, in order to determine the value of the newly developed modules. The analysis effort resulted in a set of requirements which will help the battery manufacturers to develop a module to meet the automotive Original Equipment Manufacturers (OEM) micro hybrid vehicle requirements. Battery developers were invited to submit development proposals and two proposals were selected for 50% cost share with USABC/DOE.

What is the Safest Sprint Starting Position for American Football Players?

Directory of Open Access Journals (Sweden)

Bruno Bonnechere, Benoit Beyer, Marcel Rooze, Jan Serge Van Sint

2014-06-01

Full Text Available The main objective of this study was to perform a biomechanical analysis of three different sprint start patterns to determine the safest position in term of neck injury and Sport-Related Concussion (SRC. The second objective was to collect data on the learning process effect between football players and non-players. Three different sprint initial positions adopted by football players were studied (i.e., 4-, 3- and 2-point positions. Twenty five young healthy males, including 12 football players, participated to this study. A stereophotogrammetric system (i.e., Vicon was used to record motion patterns and body segments positions. Various measurements related to head and trunk orientation, and player field-of-view were obtained (e.g., head height, trunk bending, time to reach upright position, head speed (vertical direction and body speed (horizontal direction. Learning process was found to have no influence on studied parameters. Head redress is also delayed when adopting a 4-point position leading to a reduce field-of-view during the start and increasing therefore the probability of collision. Concerning the three different positions, the 4-point position seems to be the more dangerous because leading to higher kinetic energy than the 2- and 3-point start positions. This study proposes a first biomechanical approach to understand risk/benefit balance for athletes for those three different start positions. Results suggested that the 4-point position is the most risky for football players.

Comparison between MBR and SBR on Anammox start-up process from the conventional activated sludge.

Science.gov (United States)

Wang, Tao; Zhang, Hanmin; Gao, Dawen; Yang, Fenglin; Zhang, Guangyi

2012-10-01

Anammox start-up performances from the conventional activated sludge were compared between a MBR and SBR. Both the reactors successfully started up Anammox process. The start-up period in the MBR (59 days) was notably shorter than that in the SBR (101 days), and the max nitrogen (NH(4)(+)+NO(2)(-)) removal capacity of 345.2 mg N L(-1) d(-1) in the MBR was also higher than that of 292.0 mg N L(-1) d(-1) in the SBR. FISH analysis showed that Anammox bacteria predominated in both reactors. Phylogenetic analysis further disclosed that the MBR had the better biodiversity of Anammox bacteria and gained a higher ecological stability. Generally, the results showed that MBR exhibited a more excellent performance for Anammox start-up. Crown Copyright © 2012. Published by Elsevier Ltd. All rights reserved.

Start Where Your Students Are

Science.gov (United States)

Jackson, Robyn R.

2010-01-01

Starting where your students are means understanding how currencies are negotiated and traded in the classroom. Any behavior that students use to acquire the knowledge and skills needed in the classroom functions as currency. Teachers communicate the kinds of currencies they accept in their classrooms, such as getting good grades; students do…

Insertion and professional development of starting university professors: the need for spaces for pedagogical discussion

Directory of Open Access Journals (Sweden)

Beatriz Maria Boessio Atrib Zanchet

2016-01-01

Full Text Available Current paper is the result of a research on twenty-eight starting university teachers in four universities in southern Brazil and seeks to understand their concern on pedagogical discussion spaces as a possible support for the development of their teaching practice. The research started from the point that starting teachers should insert themselves within higher education culture and find pedagogical support to develop their lectures. As a rule, they have recently obtained a doctoral degree, complying with the required academic title for their tenure, but with scanty or no pedagogical preparation. The subjects answered a semi-structured interview, with issues on the challenges, difficulties and possibilities of pedagogical support pointed out when they started their activities. The quantitative data form the corpus analyzed used in the analysis. The paper is based on studies by Garcia (1999, 2009b, Vaillant and Garcia (2012 and others. Results showed that pedagogical education and professional development of university professors, developed through pedagogical spaces, are essential for and welcomed by these teachers. An overall policy is required that valorizes the teaching tasks as fundamental for achieving teaching quality.

Getting started with Oracle WebLogic Server 12c developer's guide

CERN Document Server

Nunes, Fabio Mazanatti

2013-01-01

Getting Started with Oracle WebLogic Server 12c is a fast-paced and feature-packed book, designed to get you working with Java EE 6, JDK 7 and Oracle WebLogic Server 12c straight away, so start developing your own applications.Getting Started with Oracle WebLogic Server 12c: Developer's Guide is written for developers who are just getting started, or who have some experience, with Java EE who want to learn how to develop for and use Oracle WebLogic Server. Getting Started with Oracle WebLogic Server 12c: Developer's Guide also provides a great overview of the updated features of the 12c releas

Effects of chemical kinetics and starting material regeneration on the efficiency of an iodine laser amplifier

International Nuclear Information System (INIS)

Fisk, G.A.

1977-05-01

A model of the chemical kinetics occurring in an iodine laser amplifier is presented and used to calculate the degree to which the starting material is consumed as a result of laser operation. The cost of purchasing new starting material is estimated and shown to be prohibitive. A scheme for regenerating the starting material from the species present in the amplifier after lasing is proposed. It is shown that the estimated efficiency of this chemical regeneration process is appreciably higher than the projected optimum efficiency of the pumping process

Cause-Specific Mortality in HIV-Positive Patients Who Survived Ten Years after Starting Antiretroviral Therapy

DEFF Research Database (Denmark)

Trickey, Adam; May, Margaret T; Vehreschild, Jorg-Janne

2016-01-01

OBJECTIVES: To estimate mortality rates and prognostic factors in HIV-positive patients who started combination antiretroviral therapy between 1996-1999 and survived for more than ten years. METHODS: We used data from 18 European and North American HIV cohort studies contributing to the Antiretro......OBJECTIVES: To estimate mortality rates and prognostic factors in HIV-positive patients who started combination antiretroviral therapy between 1996-1999 and survived for more than ten years. METHODS: We used data from 18 European and North American HIV cohort studies contributing...... to the Antiretroviral Therapy Cohort Collaboration. We followed up patients from ten years after start of combination antiretroviral therapy. We estimated overall and cause-specific mortality rate ratios for age, sex, transmission through injection drug use, AIDS, CD4 count and HIV-1 RNA. RESULTS: During 50,593 person...... years 656/13,011 (5%) patients died. Older age, male sex, injecting drug use transmission, AIDS, and low CD4 count and detectable viral replication ten years after starting combination antiretroviral therapy were associated with higher subsequent mortality. CD4 count at ART start did not predict...

Fusion reactor start-up without an external tritium source

Energy Technology Data Exchange (ETDEWEB)

Zheng, S., E-mail: Shanliang.Zheng@ccfe.ac.uk; King, D.B.; Garzotti, L.; Surrey, E.; Todd, T.N.

2016-02-15

reactors. The preliminary results suggest that initial operation in D–D with continual feedback into the plasma of the tritium produced enables a fusion reactor designed solely for D–T operation to start-up in an acceptably short time-scale without the need for any external tritium source.

Body Composition and Kinematic Analysis of the Grab Start in Youth Swimmers

Directory of Open Access Journals (Sweden)

Alptekin Ahmet

2014-10-01

Full Text Available The purposes of this study were to compare the kinematic variables in youth swimmers during the grab start between sexes and to investigate the relationship between body composition and kinematic variables of the participants. Six female (Mage = 13.71 ± 0.49 yrs and seven male (Mage = 14.00 ± 1.07 yrs swimmers participated in this study. All participants were required to perform grab start tests in random order (three trials by each participant, while the best attempt was analyzed. Nineteen kinematic parameters consisting of block time, flight time, flight distance, total time, total distance, horizontal and vertical displacement of the center of mass (CM at take-off, horizontal and vertical displacement of the CM at entry, height of take-off and entry, relative height of take-off, horizontal and vertical velocity of the CM at take-off, horizontal and vertical velocity of the CM at entry, angle of take-off, angle of entry and angle of knee at block were analyzed. Out of the 19 evaluated kinematic parameters, a statistical difference between the female and male group was found only in the total distance. Therefore, both female and male groups are considered as only one group and merged after analyzing the results. Statistical analysis showed positive and negative correlations between horizontal / vertical velocity of CM at take-off and several kinematic variables (e.g. angle of entry (rhorizontal = -.868, p=.000 / rvertical = .591, p=.02, total distance (rhorizontal = .594, p=.02 / rvertical = .54, p=.04, and height of take-off (rvertical = .888, p=.000, respectively. On the other hand, positive and negative correlations were found between somatotype components and several kinematic variables (e.g. horizontal displacement of CM at entry (rendomorphy = -.626, p=.013, angle of entry (rmesomorphy = -.686, p=.005 / rectomorphy = .52, p=.047, total distance (rendomorphy = -.626, p=.012, and height of take-off (rendomorphy = -.633, p=.011

HF-START: A Regional Radio Propagation Simulator

Science.gov (United States)

Hozumi, K.; Maruyama, T.; Saito, S.; Nakata, H.; Rougerie, S.; Yokoyama, T.; Jin, H.; Tsugawa, T.; Ishii, M.

2017-12-01

HF-START (HF Simulator Targeting for All-users' Regional Telecommunications) is a user-friendly simulator developed to meet the needs of space weather users. Prediction of communications failure due to space weather disturbances is of high priority. Space weather users from various backgrounds with high economic impact, i.e. airlines, telecommunication companies, GPS-related companies, insurance companies, international amateur radio union, etc., recently increase. Space weather information provided by Space Weather Information Center of NICT is, however, too professional to be understood and effectively used by the users. To overcome this issue, I try to translate the research level data to the user level data based on users' needs and provide an immediate usable data. HF-START is positioned to be a space weather product out of laboratory based truly on users' needs. It is originally for radio waves in HF band (3-30 MHz) but higher frequencies up to L band are planned to be covered. Regional ionospheric data in Japan and southeast Asia are employed as a reflector of skywave mode propagation. GAIA (Ground-to-topside model of Atmosphere and Ionosphere for Aeronomy) model will be used as ionospheric input for global simulation. To evaluate HF-START, an evaluation campaign for Japan region will be launched in coming months. If the campaign successes, it will be expanded to southeast Asia region as well. The final goal of HF-START is to provide the near-realtime necessary radio parameters as well as the warning message of radio communications failure to the radio and space weather users.

The Rationality and Irrationality of Financing Green Start-Ups

Directory of Open Access Journals (Sweden)

Linda Bergset

2015-11-01

Full Text Available Green start-ups contribute towards a transition to a more sustainable economy by developing sustainable and environmentally friendly innovation and bringing it to the market. Due to specific product/service characteristics, entrepreneurial motivation and company strategies that might differ from that of other start-ups, these companies might struggle even more than usual with access to finance in the early stages. This conceptual paper seeks to explain these challenges through the theoretical lenses of entrepreneurial finance and behavioural finance. While entrepreneurial finance theory contributes to a partial understanding of green start-up finance, behavioural finance is able to solve a remaining explanatory deficit produced by entrepreneurial finance theory. Although some behavioural finance theorists are suggesting that the current understanding of economic rationality underlying behavioural finance research is inadequate, most scholars have not yet challenged these assumptions, which constrict a comprehensive and realistic description of the reality of entrepreneurial finance in green start-ups. The aim of the paper is thus, first, to explore the specifics of entrepreneurial finance in green start-ups and, second, to demonstrate the need for a more up-to-date conception of rationality in behavioural finance theory in order to enable realistic empirical research in this field.

Efficient use of a translation start codon in BDNF exon I.

Science.gov (United States)

Koppel, Indrek; Tuvikene, Jürgen; Lekk, Ingrid; Timmusk, Tõnis

2015-09-01

The brain-derived neurotrophic factor (BDNF) gene contains a number of 5' exons alternatively spliced with a common 3' exon. BDNF protein is synthesized from alternative transcripts as a prepro-precursor encoded by the common 3' exon IX, which has a translation start site 21 bp downstream of the splicing site. BDNF mRNAs containing exon I are an exception to this arrangement as the last three nucleotides of this exon constitute an in-frame AUG. Here, we show that this AUG is efficiently used for translation initiation in PC12 cells and cultured cortical neurons. Use of exon I-specific AUG produces higher levels of BDNF protein than use of the common translation start site, resulting from a higher translation rate. No differences in protein degradation, constitutive or regulated secretion were detected between BDNF isoforms with alternative 5' termini. As the BDNF promoter preceding exon I is known to be highly regulated by neuronal activity, our results suggest that the function of this translation start site may be efficient stimulus-dependent synthesis of BDNF protein. The brain-derived neurotrophic factor (BDNF) gene contains multiple untranslated 5' exons alternatively spliced to one common protein-coding 3' exon. However, exon I contains an in-frame ATG in a favorable translation context. Here, we show that use of this ATG is associated with more efficient protein synthesis than the commonly used ATG in exon IX. © 2015 International Society for Neurochemistry.

A simple and effective method to achieve the successful start-up of a current reference

International Nuclear Information System (INIS)

Han Lei; Zhang Xiaoxing; Dai Yujie; Lü Yingjie; Wang Yujun

2012-01-01

Start-up design is a critical issue in current reference as it is very closely related to production yield. However, its function is difficult to predict using normal transaction simulations before the device is put into diffusion. In this paper, we discuss a simple and effective simulation approach which ensures a successful start-up process in a self-biased temperature independent current reference. The circuit is implemented in a class-D power amplifier with a 0.35 μm BiCMOS process and the experimental result validates that, by using this method, the start-up success rate can be greatly improved to 100%. (semiconductor integrated circuits)

Start-up of the ohmic phase in JET

International Nuclear Information System (INIS)

Tanga, A.; Christiansen, J.P.; Cordey, J.G.; Ejima, S.; Kellman, A.; Lazzaro, E.; Lomas, P.J.; Thomas, P.R.

1985-01-01

JET has been designed to permit the study of plasmas in which alphaparticle heating is a significant part of the power balance. In order to have a sufficient thermonuclear yield and to trap the resulting alphaparticles, JET is similar in its dimensions and plasma current to the next generation of reactor-like devices such as NET, FER and INTOR. For this reason, the authors see the results from the study of the start-up of ohmically heated plasmas in JET as highly relevant. Discussed is the range that has been achieved in all major parameters with ohmic heating. Experiences with the wall conditioning technique and the results of ion cyclotron heating experiments in JET are outlined. This paper also describes the stages of plasma formation, current rise and ohmic flat-top

Motivational Factors: Drivers Behind Women Entrepreneurs’ Decision to Start an Entrepreneurial Venture in Croatia

Directory of Open Access Journals (Sweden)

Fosić Ivana

2017-10-01

Full Text Available A decision to start a business is not easy because it is result of the economic conditions, cultural context, but also “push” and “pull” factors. In order to determine woman motivational factors, a survey of 1,157 Eastern Croatia respondents was conducted. The purpose of the research was to determine which motivations the potential future entrepreneurs believe trigger women entrepreneurs’ decision to start an entrepreneurial venture. The results show that women are considered to be financially motivated. The fact that real-life women entrepreneurs from previous research have stated slightly different motivations shows that there is room for improvement of entrepreneurship education.

An Integrated Start-Up Method for Pumped Storage Units Based on a Novel Artificial Sheep Algorithm

Directory of Open Access Journals (Sweden)

Zanbin Wang

2018-01-01

Full Text Available Pumped storage units (PSUs are an important storage tool for power systems containing large-scale renewable energy, and the merit of rapid start-up enable PSUs to modulate and stabilize the power system. In this paper, PSU start-up strategies have been studied and a new integrated start-up method has been proposed for the purpose of achieving swift and smooth start-up. A two-phase closed-loop startup strategy, composed of switching Proportion Integration (PI and Proportion Integration Differentiation (PID controller is designed, and an integrated optimization scheme is proposed for a synchronous optimization of the parameters in the strategy. To enhance the optimization performance, a novel meta-heuristic called Artificial Sheep Algorithm (ASA is proposed and applied to solve the optimization task after a sufficient verification with seven popular meta-heuristic algorithms and 13 typical benchmark functions. Simulation model has been built for a China’s PSU and comparative experiments are conducted to evaluate the proposed integrated method. Results show that the start-up performance could be significantly improved on both indices on overshoot and start-up, and up to 34%-time consumption has been reduced under different working condition. The significant improvements on start-up of PSU is interesting and meaning for further application on real unit.

Starting a nursing consultation practice.

Science.gov (United States)

Schulmeister, L

1999-03-01

Because the clinical nurse specialist (CNS) role has been changed or eliminated in many hospital organizations, many CNSs in career transition are considering establishing collaborative or independent nursing consultation practices. Opportunities for consultants exist in diverse practice settings and specialties. Before starting a consultation practice, the CNS should carefully examine goals, identify resources, and begin contacting potential referral sources. He or she must also decide what form of business organization to establish and write a business plan to solidify ideas and prepare for the unexpected. Most CNS consultants rely on personal savings to cover initial business and personal expenses, and many continue working as a CNS until the consultation practice is established. Fees can be set based on community standards, what the market will bear, desired projected income, or a third-party payor's fee schedule. The consultation practice can be marketed by word of mouth, inexpensive advertising techniques such as distributing flyers and business cards, direct mall, and media advertising. In today's healthcare marketplace, opportunities abound for the CNS risk-taker interested in starting a nursing consultation practice.

LHC Report: Rocky re-start

CERN Multimedia

Barbara Holzer for the LHC Team

2012-01-01

A rocky re-start with beam followed a successful machine development period and the first technical stop of 2012. Today, Friday 11 May, the machine began running again with 1380 bunches.   A short, two-day machine development period was successfully completed on 21-22 April. It focused on topics relevant for the 2012 physics beam operation. This was then followed by a five-day technical stop, the first of the year. The technical stop finished on time on Friday 26 April. The re-start with beam was somewhat tortuous and hampered by an unlucky succession of technical faults leading to extended periods of downtime. The planned intensity increase was put on hold for three days with the machine operating with 1092 bunches and a moderate bunch intensity of 1.3x1011 protons. This delivered a reasonable peak luminosity of 3.6x1033 cm-2s-1 to ATLAS and CMS. Higher than usual beam losses were observed in the ramp and squeeze, and time was required to investigate the causes and to implement mitigati...

[How to start a neuroimaging study].

Science.gov (United States)

Narumoto, Jin

2012-06-01

In order to help researchers understand how to start a neuroimaging study, several tips are described in this paper. These include 1) Choice of an imaging modality, 2) Statistical method, and 3) Interpretation of the results. 1) There are several imaging modalities available in clinical research. Advantages and disadvantages of each modality are described. 2) Statistical Parametric Mapping, which is the most common statistical software for neuroimaging analysis, is described in terms of parameter setting in normalization and level of significance. 3) In the discussion section, the region which shows a significant difference between patients and normal controls should be discussed in relation to the neurophysiology of the disease, making reference to previous reports from neuroimaging studies in normal controls, lesion studies and animal studies. A typical pattern of discussion is described.

Getting started with Microsoft Lync server 2013

CERN Document Server

Volpe, Fabrizio

2013-01-01

This book has a practical approach with a lot of step-by-step guides and explanations as to where and why we're doing the various operations.Getting Started with Microsoft Lync Server 2013 is a starting point for system administrators, IT pros, unified communication technicians, and decision makers in companies or in the consultancy business. For people who have never managed Lync (or a U.C. product), the book will guide you through the basic concepts and mistakes. If you are already managing a Lync deployment you will find important explanations and ideas put together in a single text. If you

Entrepreneur How to Start an Online Business

CERN Document Server

Tobin, Lucy

2012-01-01

The secrets of the UK’s biggest online entrepreneurs revealed   Thinking of starting a business? Already have a business online and looking to take it to the next level? The wonderful world wide web has made creating a start-up that much easier. Thousands of people are out there reaping the rewards the web can bring. If you want to join them, you’ve come to the right place.  Profiling today’s foremost web entrepreneurs, Lucy Tobin - who meets successful business founders every week writing an enterprise column for The Evening Standard – takes us throug

A novel approach to delayed-start analyses for demonstrating disease-modifying effects in Alzheimer's disease.

Directory of Open Access Journals (Sweden)

Hong Liu-Seifert

Full Text Available One method for demonstrating disease modification is a delayed-start design, consisting of a placebo-controlled period followed by a delayed-start period wherein all patients receive active treatment. To address methodological issues in previous delayed-start approaches, we propose a new method that is robust across conditions of drug effect, discontinuation rates, and missing data mechanisms. We propose a modeling approach and test procedure to test the hypothesis of noninferiority, comparing the treatment difference at the end of the delayed-start period with that at the end of the placebo-controlled period. We conducted simulations to identify the optimal noninferiority testing procedure to ensure the method was robust across scenarios and assumptions, and to evaluate the appropriate modeling approach for analyzing the delayed-start period. We then applied this methodology to Phase 3 solanezumab clinical trial data for mild Alzheimer's disease patients. Simulation results showed a testing procedure using a proportional noninferiority margin was robust for detecting disease-modifying effects; conditions of high and moderate discontinuations; and with various missing data mechanisms. Using all data from all randomized patients in a single model over both the placebo-controlled and delayed-start study periods demonstrated good statistical performance. In analysis of solanezumab data using this methodology, the noninferiority criterion was met, indicating the treatment difference at the end of the placebo-controlled studies was preserved at the end of the delayed-start period within a pre-defined margin. The proposed noninferiority method for delayed-start analysis controls Type I error rate well and addresses many challenges posed by previous approaches. Delayed-start studies employing the proposed analysis approach could be used to provide evidence of a disease-modifying effect. This method has been communicated with FDA and has been

Testing the START Triage Protocol: Can It Improve the Ability of Nonmedical Personnel to Better Triage Patients During Disasters and Mass Casualties Incidents ?

Science.gov (United States)

Badiali, Stefano; Giugni, Aimone; Marcis, Lucia

2017-06-01

START (Simple Triage and Rapid Treatment) triage is a tool that is available even to nonmedical rescue personnel in case of a disaster or mass casualty incident (MCI). In Italy, no data are available on whether application of the START protocol could improve patient outcomes during a disaster or MCI. We aimed to address whether "last-minute" START training of nonmedical personnel during a disaster or MCI would result in more effective triage of patients. In this case-control study, 400 nonmedical ambulance crew members were randomly assigned to a non-START or a START group (200 per group). The START group received last-minute START training. Each group examined 6000 patients, obtained from the Emergo Train System (ETS Italy, Bologna, Italy) victims database, and assigned patients a triage code (black-red-yellow-green) along with a reason for the assignment. Each rescuer triaged 30 patients within a 30-minute time frame. Results were analyzed according to Fisher's exact test for a P valueSTART group completed the evaluations in 15 minutes, whereas the non-START group took 30 minutes. The START group correctly triaged 94.2% of their patients, as opposed to 59.83% of the non-START group (PSTART group versus 13.67% and 26.5% for the non-START group. The non-START group had 458 "preventable deaths" on 6000 cases because of incorrect triage, whereas the START group had 91. Even a "last-minute" training on the START triage protocol allows nonmedical personnel to better identify and triage the victims of a disaster or MCI, resulting in more effective and efficient medical intervention. (Disaster Med Public Health Preparedness. 2017;11:305-309).

13 CFR 305.11 - Contract awards; early construction start.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Contract awards; early construction start. 305.11 Section 305.11 Business Credit and Assistance ECONOMIC DEVELOPMENT ADMINISTRATION... § 305.11 Contract awards; early construction start. EDA must determine that the award of all contracts...

Later school start times for supporting the education, health, and well-being of high school students.

Science.gov (United States)

Marx, Robert; Tanner-Smith, Emily E; Davison, Colleen M; Ufholz, Lee-Anne; Freeman, John; Shankar, Ravi; Newton, Lisa; Brown, Robert S; Parpia, Alyssa S; Cozma, Ioana; Hendrikx, Shawn

2017-07-03

outcomes (health behaviors, health and safety indicators, social outcomes, family outcomes, school outcomes, or community outcomes) were eligible. At least two review authors independently determined inclusion and exclusion decisions through screening titles, abstracts, and full-text reports. Two review authors independently extracted data for all eligible studies. We presented findings through a narrative synthesis across all studies. When two or more study samples provided sufficient information to permit effect size calculations, we conducted random-effects meta-analyses to synthesize effects across studies. Our search located 17 eligible records reporting on 11 unique studies with 297,994 participants; the studies examined academic outcomes, amount and quality of sleep, mental health indicators, attendance, and student alertness. Overall, the quality of the body of evidence was very low, as we rated most studies as being at high or unclear risk of bias with respect to allocation, attrition, absence of randomization, and the collection of baseline data. Therefore, we cannot be confident about the effects of later school start times.Preliminary evidence from the included studies indicated a potential association between later school start times and academic and psychosocial outcomes, but quality and comparability of these data were low and often precluded quantitative synthesis. Four studies examined the association between later school start times and academic outcomes, reporting mixed results. Six studies examined effects on total amount of sleep and reported significant, positive relationships between later school start times and amount of sleep. One study provided information concerning mental health outcomes, reporting an association between decreased depressive symptoms and later school start times. There were mixed results for the association between later school start times and absenteeism. Three studies reported mixed results concerning the association between

Western Pond Turtle Head-starting and Reintroduction; 2004-2005 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Van Leuven, Susan; Allen, Harriet; Slavin, Kate (Washington Department of Fish and Wildlife, Wildlife Management Program, Olympia, WA)

2005-09-01

This report covers the results of the western pond turtle head-starting and reintroduction project for the period of October 2004-September 2005. Wild hatchling western pond turtles from the Columbia River Gorge were reared at the Woodland Park and Oregon Zoos in 2004 and 2005 as part of the recovery effort for this Washington State endangered species. The objective of the program is to reduce losses to introduced predators like bullfrogs and largemouth bass by raising the hatchlings to a size where they are too large to be eaten by most of these predators. Thirty-five turtles were placed at the Woodland Park Zoo and 53 at the Oregon Zoo. Of these, 77 head-started juvenile turtles were released at three sites in the Columbia Gorge in 2005. Four were held back to attain more growth in captivity. Eleven were released at the Klickitat ponds, 22 at the Klickitat lake, 39 at the Skamania site, and 5 at Pierce National Wildlife Refuge (NWR). This brought the total number of head-start turtles released since 1991 to 257 for the Klickitat ponds, 136 for the Klickitat lake, 206 for the Skamania pond complex, and 255 at Pierce NWR. In 2005, 34 females from the two Columbia Gorge populations were equipped with transmitters and monitored for nesting activity. Twenty-four nests were located and protected; these produced 90 hatchlings. The hatchlings were collected in September and transported to the Oregon and Woodland Park zoos for rearing in the head-start program. During the 2005 field season trapping effort, 486 western pond turtles were captured in the Columbia Gorge, including 430 previously head-started turtles. These recaptures, together with confirmed nesting by head-start females and visual resightings, indicate the program is succeeding in boosting juvenile recruitment to increase the populations. Records were also collected on 216 individual painted turtles captured in 2005 during trapping efforts at Pierce NWR, to gather baseline information on this native

Western Pond Turtle Head-starting and Reintroduction, 2005-2006 Annual Report.

Energy Technology Data Exchange (ETDEWEB)

Van Leuven, Susan; Allen, Harriet; Slavens, Kate (Washington Department of Fish and Wildlife, Wildlife Management Program, Olympia, WA)

2006-11-01

This report covers the results of the western pond turtle head-starting and reintroduction project for the period of October 2005-September 2006. Wild hatchling western pond turtles from the Columbia River Gorge were reared at the Woodland Park and Oregon zoos in 2005 and 2006 as part of the recovery effort for this Washington State endangered species. The objective of the program is to reduce losses to introduced predators like bullfrogs and largemouth bass by raising the hatchlings to a size where they are too large to be eaten by most of these predators. Twenty-six turtles were placed at the Woodland Park Zoo and 62 at the Oregon Zoo in fall 2005. These turtles joined two that were held back from release in summer 2005 due to their small size. All 90 juvenile turtles were released at three sites in the Columbia Gorge in 2006. Twenty-eight juvenile turtles were released at the Klickitat ponds, 22 at the Klickitat lake, 21 at the Skamania site, and 19 at Pierce National Wildlife Refuge (NWR). This brought the total number of head-start turtles released since 1991 to 944; 285 for the Klickitat ponds, 158 for the Klickitat lake, 227 for the Skamania pond complex, and 274 at Pierce NWR. In 2006, 20 females from the Klickitat population were equipped with transmitters and monitored for nesting activity. Fifteen nests were located and protected; these produced 55 hatchlings. The hatchlings were collected in September and transported to the Oregon and Woodland Park zoos for rearing in the head-start program. One wild hatchling captured in spring 2006 was placed in the head-start program to attain more growth in captivity. During the 2006 field season trapping effort, 414 western pond turtles were captured in the Columbia Gorge, including 374 previously head-started turtles. These recaptures, together with confirmed nesting by head-start females and visual resightings, indicate the program is succeeding in boosting juvenile recruitment to increase the populations

Dynamic factors and electromyographic activity in a sprint start

Directory of Open Access Journals (Sweden)

M Čoh

2009-07-01

Full Text Available The aim of the study was to establish the major dynamic parameters as well as the EMG activation of muscles in a sprint start as the first derivative of sprint velocity. The subject of the analysis was block velocity, the production of force in the front and rear starting blocks, the block acceleration in the first two steps and the electromyographic activity (EMG of the following muscles: the erector spinae muscle, gluteus maximus muscle, rectus femoris muscle, vastus medialis muscle, vastus lateralis muscle, biceps femoris muscle and gastrocnemius–medialis muscle. One international-class female sprinter participated in the experiment. She performed eight starts in constant laboratory conditions. The 3-D kinematic analysis was made using a system of nine Smart-e 600 cameras operating at a frame rate of 60 Hz. Dynamic parameters were established by means of two separate force platforms to which the starting blocks were fixed. A 16-channel electromyograph was used to analyse electromyographic activity (EMG. It was established that the block velocity depended on the absolute force produced in the front and rear starting blocks and that it was 2.84±0.21 m.s-1. The maximal force on the rear and front blocks was 628±34 N and 1023±30 N, respectively. In view of the total impulse (210±11 Ns the force production/time ratio in the rear and front blocks was 34%:66%. The erector spinae muscle, vastus lateralis muscle and gastrocnemius–medialis muscle generate the efficiency of the start. The block acceleration in the first two steps primarily depends on the activation of the gluteus maximus muscle, rectus femoris muscle, biceps femoris muscle and gastrocnemius–medialis muscle. A sprint start is a complex motor stereotype requiring a high degree of integration of the processes of central movement regulation and an optimal level of biomotor abilities.

Fast Thorium Molten Salt Reactors Started with Plutonium

International Nuclear Information System (INIS)

Merle-Lucotte, E.; Heuer, D.; Le Brun, C.; Brissot, R.; Liatard, E.; Meplan, O.; Nuttin, A.; Mathieu, L.

2006-01-01

One of the pending questions concerning Molten Salt Reactors based on the 232 Th/ 233 U fuel cycle is the supply of the fissile matter, and as a consequence the deployment possibilities of a fleet of Molten Salt Reactors, since 233 U does not exist on earth and is not yet produced in the current operating reactors. A solution may consist in producing 233 U in special devices containing Thorium, in Pressurized Water or Fast Neutrons Reactors. Two alternatives to produce 233 U are examined here: directly in standard Molten Salt Reactors started with Plutonium as fissile matter and then operated in the Th/ 233 U cycle; or in dedicated Molten Salt Reactors started and fed with Plutonium as fissile matter and Thorium as fertile matter. The idea is to design a critical reactor able to burn the Plutonium and the minor actinides presently produced in PWRs, and consequently to convert this Plutonium into 233 U. A particular reactor configuration is used, called 'unique channel' configuration in which there is no moderator in the core, leading to a quasi fast neutron spectrum, allowing Plutonium to be used as fissile matter. The conversion capacities of such Molten Salt Reactors are excellent. For Molten Salt Reactors only started with Plutonium, the assets of the Thorium fuel cycle turn out to be quickly recovered and the reactor's characteristics turn out to be equivalent to Molten Salt Reactors operated with 233 U only. Using a combination of Molten Salt Reactors started or operated with Plutonium and of Molten Salt Reactors started with 233 U, the deployment capabilities of these reactors fully satisfy the condition of sustainability. (authors)

Getting started with OrientDB

CERN Document Server

Tesoriero, Claudio

2013-01-01

A standard tutorial aimed at making you an OrientDB expert, through the use of practical examples, explained in a step-by-step format.Getting Started with OrientDB 1.3.0 is great for database designers, developers, and systems engineers. It is assumed that you are familiar with NoSQL concepts, Java, and networking principles.

Decision Enhancement Services for Small and Medium Enterprise Start-Ups in Uganda

NARCIS (Netherlands)

Sol, H G; Basaza, Habinka; Sprague, Ralph H.

2012-01-01

While start-up firms create a substantial economic impact on most economies, the failure rate of start-up firms seems to remain high due to inadequate agile decision services. Deciding to start-up mining Small and Medium Enterprises (SME) is a challenging task in Uganda. Research on SME start-up

School Start Times, Sleep, Behavioral, Health, and Academic Outcomes: A Review of the Literature.

Science.gov (United States)

Wheaton, Anne G; Chapman, Daniel P; Croft, Janet B

2016-05-01

Insufficient sleep in adolescents has been shown to be associated with a wide variety of adverse outcomes, from poor mental and physical health to behavioral problems and lower academic grades. However, most high school students do not get sufficient sleep. Delaying school start times for adolescents has been proposed as a policy change to address insufficient sleep in this population and potentially to improve students' academic performance, reduce engagement in risk behaviors, and improve health. This article reviews 38 reports examining the association between school start times, sleep, and other outcomes among adolescent students. Most studies reviewed provide evidence that delaying school start time increases weeknight sleep duration among adolescents, primarily by delaying rise times. Most of the studies saw a significant increase in sleep duration even with relatively small delays in start times of half an hour or so. Later start times also generally correspond to improved attendance, less tardiness, less falling asleep in class, better grades, and fewer motor vehicle crashes. Although additional research is necessary, research results that are already available should be disseminated to stakeholders to enable the development of evidence-based school policies. Published 2016. This article is a U.S. Government work and is in the public domain in the USA.

New start-up channels and multichannel analyzer at the RB reactor; Novi start-up kanali i videkanalni analizator na reaktoru Rb

Energy Technology Data Exchange (ETDEWEB)

Sotic, O; Markovic, H; Vranic, S; Dimitrijevic, Z; Pesic, M [Boris Kidric Institute of Nuclear Sciences Vinca, Beograd (Yugoslavia)

1978-01-15

New start-up channels and a multichannel analyzer were purchased in 1977 for the RB reactor. Both start-up channels contain BF{sub 3} neutron detectors, preamplifier, amplifier, single-channel analyzer, scaler, ratemeter, control unit, recording instrument. This document contains detailed technical description of these devices as well as characteristics of the multichannel analyzer which is being tested and will be used for measuring irradiation in the vicinity of the reactor.

40 CFR 86.136-90 - Engine starting and restarting.

Science.gov (United States)

2010-07-01

... automatic chokes shall be operated according to the manufacturer's operating instructions in the owner's...) The transmission shall be placed in gear 15 seconds after the engine is started. If necessary, braking... instructions in the owner's manual do not specify a warm engine starting procedure, the engine (automatic and...

46 CFR 62.35-35 - Starting systems for internal-combustion engines.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Starting systems for internal-combustion engines. 62.35-35 Section 62.35-35 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) MARINE... Starting systems for internal-combustion engines. The starting systems for propulsion engines and for prime...

Group cohesion and starting status in successful and less successful elite volleyball teams.

Science.gov (United States)

Spink, K S

1992-08-01

The main purpose of this study was to examine the relationship between members' perceptions of group cohesion and starting status in elite volleyball teams. The results of the study revealed that the form of the cohesion-starting status relationship was moderated by the variable of success. The results for less successful teams revealed that differences did emerge between specific measures of cohesion endorsed by starters and non-starters. No such differences in cohesion emerged when the starters and non-starters on successful teams were compared. These results provide initial support for the suggestion that the most successful teams are the ones where the perceptions of cohesiveness by starters and non-starters are similar. A secondary purpose of the study was to determine whether those teams that were the most successful and similar in their members' perceptions of cohesiveness, were also the teams whose members have the most positive outcome expectancy. The results supported this prediction.

Experience from start-ups of the first ANITA Mox plants.

Science.gov (United States)

Christensson, M; Ekström, S; Andersson Chan, A; Le Vaillant, E; Lemaire, R

2013-01-01

ANITA™ Mox is a new one-stage deammonification Moving-Bed Biofilm Reactor (MBBR) developed for partial nitrification to nitrite and autotrophic N-removal from N-rich effluents. This deammonification process offers many advantages such as dramatically reduced oxygen requirements, no chemical oxygen demand requirement, lower sludge production, no pre-treatment or requirement of chemicals and thereby being an energy and cost efficient nitrogen removal process. An innovative seeding strategy, the 'BioFarm concept', has been developed in order to decrease the start-up time of new ANITA Mox installations. New ANITA Mox installations are started with typically 3-15% of the added carriers being from the 'BioFarm', with already established anammox biofilm, the rest being new carriers. The first ANITA Mox plant, started up in 2010 at Sjölunda wastewater treatment plant (WWTP) in Malmö, Sweden, proved this seeding concept, reaching an ammonium removal rate of 1.2 kgN/m³ d and approximately 90% ammonia removal within 4 months from start-up. This first ANITA Mox plant is also the BioFarm used for forthcoming installations. Typical features of this first installation were low energy consumption, 1.5 kW/NH4-N-removed, low N₂O emissions, started up at Sundets WWTP in Växjö, Sweden, reached full capacity with more than 90% ammonia removal within 2 months from start-up. By applying a nitrogen loading strategy to the reactor that matches the capacity of the seeding carriers, more than 80% nitrogen removal could be obtained throughout the start-up period.

An Ultra Low Noise Self-Starting Pulse Generator

DEFF Research Database (Denmark)

Lasri, J.; Bilenca, A.; Dahan, D.

2002-01-01

We describe a self-starting optical pulse source generating 10 GHz, 15 ps pulses with an average jitter of 43 fs and a o.15% amplitude noise over a frequency range of 500 Hz - 1 MHz.......We describe a self-starting optical pulse source generating 10 GHz, 15 ps pulses with an average jitter of 43 fs and a o.15% amplitude noise over a frequency range of 500 Hz - 1 MHz....

JUMP KINETIC DETERMINANTS OF SPRINT ACCELERATION PERFORMANCE FROM STARTING BLOCKS IN MALE SPRINTERS

Directory of Open Access Journals (Sweden)

Peter S. Maulder

2006-06-01

Full Text Available The purpose of this research was to identify the jump kinetic determinants of sprint acceleration performance from a block start. Ten male (mean ± SD: age 20 ± 3 years; height 1.82 ± 0.06 m; weight 76.7 ± 7.9 kg; 100 m personal best: 10.87 + 0.36 s {10.37 - 11.42} track sprinters at a national and regional competitive level performed 10 m sprints from a block start. Anthropometric dimensions along with squat jump (SJ, countermovement jump (CMJ, continuous straight legged jump (SLJ, single leg hop for distance, and single leg triple hop for distance measures of power were also tested. Stepwise multiple regression analysis identified CMJ average power (W/kg as a predictor of 10 m sprint performance from a block start (r = 0.79, r2 = 0.63, p<0.01, SEE = 0.04 (s, %SEE = 2.0. Pearson correlation analysis revealed CMJ force and power (r = -0.70 to -0.79; p = 0.011 - 0.035 and SJ power (r = -0.72 to -0.73; p = 0.026 - 0.028 generating capabilities to be strongly related to sprint performance. Further linear regression analysis predicted an increase in CMJ average and peak take-off power of 1 W/kg (3% & 1.5% respectively to both result in a decrease of 0.01 s (0.5% in 10 m sprint performance. Further, an increase in SJ average and peak take-off power of 1 W/kg (3.5% & 1.5% respectively was predicted to result in a 0.01 s (0.5% reduction in 10 m sprint time. The results of this study seem to suggest that the ability to generate power both elastically during a CMJ and concentrically during a SJ to be good indicators of predicting sprint performance over 10 m from a block start

Start-Up Size Strategy and Risk Management: Impact on New Venture Performance

OpenAIRE

André van Stel; Andrew Burke; José Maria Millán; Concepcion Roman

2013-01-01

Start-up size is a key strategic decision for entrepreneurs. Should entrepreneurs start up close to minimum efficient scale or should they take less risks and start-up on a smaller scale? Previously, this strategic decision appeared to be one of simply making a choice between a higher risk/reward larger start-up versus a lower risk/reward smaller scale start-up. However, recent research on the relationship between risk management and performance (Burke, 2009) indicates that in situations of g...

Start-up of spherical tokamak without a center solenoid

International Nuclear Information System (INIS)

Maekawa, Takashi; Nagata, Masayoshi

2012-01-01

For low-aspect tokamak reactors, spherical tokamak reactors, ST-type FESF/CTFs, it is essential to remove or minimize a central solenoid (CS). Even with the minimized CS, non-inductive start up of the plasma current is required. Rapid increase in the spontaneous plasma current at the final stage of current start-up drives ignition. At the initial stage, formation of plasma and magnetic surfaces are required. As non-inductive plasma start-up scenarios, ECH/ECCD, LHCD, HHFW, DC HELICITY injection, plasma merging and NBI have been studied. In the present article, the present status and future prospect of experimental and theoretical works on these subjects. (author)

Start-up First Term Sheet: Stumbling Blocks to Avoid

Directory of Open Access Journals (Sweden)

Amalyan Nataly D.

2018-01-01

Full Text Available Start-up relationships with business angel and/or venture capital are similar to a marriage – but with a divorce in mind. The latter necessitates a proper prenuptial agreement signing at the very beginning of the relations. In case of business angel and/or venture capital we are speaking about Term sheet, determining pricing, powers and duties of the board, as well as information, participation and protective rights for the partners. Standard Term sheet consists of three buckets of provisions, defining: (i terms impacting start-up valuation and economic division of profits and proceeds upon a liquidity event, (ii terms impacting control over decision making and (iii investor protection terms. This article focuses on financial and economic aspects of funding agreement, exposing some tricky parts of the Term sheet, threatening to transform potential win-win deals into rupture of relations, crash of the company or even legal battles. The results of the analysis are used to substantiate growing in popular appeal thesis that raising too much money can be detrimental for a startup.

Head Start FACES: Longitudinal Findings on Program Performance. Third Progress Report.

Science.gov (United States)

Zill, Nicholas; Resnick, Gary; Kim, Kwang; McKey, Ruth Hubbell; Clark, Cheryl; Pai-Samant, Shefali; Connell, David; Vaden-Kiernan, Michael; O'Brien, Robert; D'Elio, Mary Ann

The Head Start Family and Child Experiences Survey (FACES) is an ongoing, national, longitudinal study of the cognitive, social, emotional, and physical development of Head Start children; the characteristics, well-being, and accomplishments of families; the observed quality of Head Start classrooms; and the characteristics and opinions of Head…

Internationalisation of high-tech start-ups and fast growth-evidence for UK and Germany

OpenAIRE

Bürgel, Oliver; Fier, Andreas; Licht, Georg; Murray, Gordon

2000-01-01

For firms acting in technological niches the expansion into foreign markets can be a way to increase sales and to thus to recover initial sunk costs over a shorter time frame. Our research, based on survey data for nearly 600 British and German high-tech start-ups, examines whether internationalisation leads to faster growth among high-tech start-ups. Results show that firms with international sales have higher sales growth than firms that sell only domestically. We find that technological so...

Longitudinal Outcomes of Start Time Delay on Sleep, Behavior, and Achievement in High School

Science.gov (United States)

Thacher, Pamela V.; Onyper, Serge V.

2016-01-01

Study Objectives: To establish whether sleep, health, mood, behavior, and academics improved after a 45-minute delay in high school start time, and whether changes persisted longitudinally. Methods: We collected data from school records and student self-report across a number of domains at baseline (May 2012) and at two follow-up time points (November 2012 and May 2013), at a public high school in upstate New York. Students enrolled during academic years (AY) 2011–2012 and 2012–2013 completed the Pittsburgh Sleep Quality Index; the DASS-21; the “Owl-Lark” Scale; the Daytime Sleepiness Index; and a brief self-report of health. Reports from school records regarding attendance, tardiness, disciplinary violations, and academic performance were collected for AY 2010–2011 through 2013–2014. Results: Students delayed but did not extend their sleep period; we found lasting improvements in tardiness and disciplinary violations after the start-time delay, but no changes to other variables. At the first follow-up, students reported 20 minutes longer sleep, driven by later rise times and stable bed times. At the second follow-up, students maintained later rise times but delayed bedtimes, returning total sleep to baseline levels. A delay in rise time, paralleling the delay in the start time that occurred, resulted in less tardiness and decreased disciplinary incidents, but larger improvements to sleep patterns may be necessary to affect health, attendance, sleepiness, and academic performance. Conclusions: Later start times improved tardiness and disciplinary issues at this school district. A delay in start time may be a necessary but not sufficient means to increase sleep time and may depend on preexisting individual differences. Commentary: A commentary on this article appears in this issue on page 267. Citation: Thacher PV, Onyper SV. Longitudinal outcomes of start time delay on sleep, behavior, and achievement in high school. SLEEP 2016;39(2):271–281. PMID

Bootstrap finance: the art of start-ups.

Science.gov (United States)

Bhide, A

1992-01-01

Entrepreneurship is more popular than ever: courses are full, policymakers emphasize new ventures, managers yearn to go off on their own. Would-be founders often misplace their energies, however. Believing in a "big money" model of entrepreneurship, they spend a lot of time trying to attract investors instead of using wits and hustle to get their ideas off the ground. A study of 100 of the 1989 Inc. "500" list of fastest growing U.S. start-ups attests to the value of bootstrapping. In fact, what it takes to start a business often conflicts with what venture capitalists require. Investors prefer solid plans, well-defined markets, and track records. Entrepreneurs are heavy on energy and enthusiasm but may be short on credentials. They thrive in rapidly changing environments where uncertain prospects may scare off established companies. Rolling with the punches is often more important than formal plans. Striving to adhere to investors' criteria can diminish the flexibility--the try-it, fix-it approach--an entrepreneur needs to make a new venture work. Seven principles are basic for successful start-ups: get operational fast; look for quick break-even, cash-generating projects; offer high-value products or services that can sustain direct personal selling; don't try to hire the crack team; keep growth in check; focus on cash; and cultivate banks early. Growth and change are the start-up's natural environment. But change is also the reward for success: just as ventures grow, their founders usually have to take a fresh look at everything again: roles, organization, even the very policies that got the business up and running.

Agile metodologies use for software development in Slovenian start-ups

OpenAIRE

Kašnik, Matic

2014-01-01

The thesis presents and describes the use of agile methodologies which are being used by Slovenian tech start-up companies. It describes the basic features, advantages and disadvantages of various agile methodologies such as Scrum, extreme programming, lean start-up and method Kanban. We made a review of the most used agile methodologies in Slovenian technology start-up companies. In particular, we focus on variety of tools, technics and approaches used by the development teams and where do t...

Single start multiple stop time digitizer

International Nuclear Information System (INIS)

Deshpande, P.A.; Mukhopadhyay, P.K.; Gopalakrishnan, K.R.

1997-01-01

A single start multiple stop time digitizer has been developed which can digitize the time between a start pulse and multiple stop pulses. The system has been designed as a PC add on card. The resolution of the instrument is 10 nSecs and the maximum length of time that it can measure is 1.28 milliseconds. Apart from time digitization, it can also resolve the height of the incoming pulses into 64 levels. After each input pulse the system dead time is less than 300 nSecs. The driver software for this card has been developed on DOS platform. It uses graphical user interface to provide a user friendly environment. The system is intended to be used in time of flight mass spectroscopy experiments. It can also be used for time of flight experiments in nuclear physics. (author). 2 figs

Lean and global technology start-ups

DEFF Research Database (Denmark)

Tanev, Stoyan; Rasmussen, Erik Stavnsager; Zijdemans, Erik

2015-01-01

In this paper the authors introduce the concept of Lean Global Start-up (LGS) as a way of emphasizing the impossibility for new technology start-ups to deal separately with business development, innovation and early internationalization. For a newly established technology firm the task of being...... global and innovative at the same time should be seen as one process. The paper has two components – an introductory conceptual part and an empirical part that should be considered as basis for the preliminary validation of the conceptual insights. The research sample includes six firms – three from...... Canada and three from Denmark. The firms have had significant problems with the complexity, uncertainties and risks of being innovative on a global scale. They have however found ways of addressing these problems by a disciplined knowledge sharing and IP protection strategy and the efficient use...

Secondary Circuit Start Up Chemistry Optimisation

International Nuclear Information System (INIS)

Fontan, Guillaume; Morel, Pascal

2012-09-01

In a context of investment and renewal of equipment, Electricite De France (EDF) put enhanced efforts on operating practices during start-up of the secondary circuit, in order to improve operational performance and materials lifetime. This article focuses on the objective of optimizing the filling, the chemical conditioning and the thermal conditioning of the secondary fluid, while taking into account the following issues: - Limiting the time required to obtain a proper chemistry, - Limiting the amount of water and steam used, - Limiting the amount of effluent generated. The scope is all start-up conditions of secondary circuit, both after refuelling outage or fortuitous shutdowns of the plant. The recommendations produced are based on existing local procedures and good practices, which were collected and developed in order to propose a generic methodology understandable and useful both for operators, chemists and managers. (authors)

Optimization of Passive Voltage Multipliers for Fast Start-up and Multi-voltage Power Supplies in Electromagnetic Energy Harvesting Systems

Science.gov (United States)

Yang, G.; Stark, B. H.; Burrow, S. G.; Hollis, S. J.

2014-11-01

This paper demonstrates the use of passive voltage multipliers for rapid start-up of sub-milliwatt electromagnetic energy harvesting systems. The work describes circuit optimization to make as short as possible the transition from completely depleted energy storage to the first powering-up of an actively controlled switched-mode converter. The dependency of the start-up time on component parameters and topologies is derived by simulation and experimentation. The resulting optimized multiplier design reduces the start-up time from several minutes to 1 second. An additional improvement uses the inherent cascade structure of the voltage multiplier to power sub-systems at different voltages. This multi-rail start-up is shown to reduce the circuit losses of the active converter by 72% with respect to the optimized single-rail system. The experimental results provide insight into the multiplier's transient behaviour, including circuit interactions, in a complete harvesting system, and offer important information to optimize voltage multipliers for rapid start-up.

Optimization of Passive Voltage Multipliers for Fast Start-up and Multi-voltage Power Supplies in Electromagnetic Energy Harvesting Systems

International Nuclear Information System (INIS)

Yang, G; Stark, B H; Burrow, S G; Hollis, S J

2014-01-01

This paper demonstrates the use of passive voltage multipliers for rapid start-up of sub-milliwatt electromagnetic energy harvesting systems. The work describes circuit optimization to make as short as possible the transition from completely depleted energy storage to the first powering-up of an actively controlled switched-mode converter. The dependency of the start-up time on component parameters and topologies is derived by simulation and experimentation. The resulting optimized multiplier design reduces the start-up time from several minutes to 1 second. An additional improvement uses the inherent cascade structure of the voltage multiplier to power sub-systems at different voltages. This multi-rail start-up is shown to reduce the circuit losses of the active converter by 72% with respect to the optimized single-rail system. The experimental results provide insight into the multiplier's transient behaviour, including circuit interactions, in a complete harvesting system, and offer important information to optimize voltage multipliers for rapid start-up

Dynamics and Control During Start-Up of Energy Integrated Distillation Column

DEFF Research Database (Denmark)

of the inherent effects of process integration upon a start-up procedure. In particular the effect of energy recycle upon the possible start-up sequence, and the effect of using an actuator for control purposes, i.e. the heat pump, which in itself requires significant start-up time. The experimental application...

Guide to Improving Parenting Education in Even Start Family Literacy Programs.

Science.gov (United States)

Powell, Douglas R.; D'Angelo, Diane

This guide provides a framework and suggestions for strengthening the quality and impact of parenting education services in Even Start. It is aimed at Even Start state coordinators and local program administrators responsible for supporting and monitoring the quality of parenting education services in Even Start, and at local program staff…

RA-6 reactor's probabilistic safety evaluation. Identification and selection of starting events

International Nuclear Information System (INIS)

Kay, J.; Chiossi, C.; Felizia, E.; Vallerga, H.; Kalejman, G.; Navarro, R.; Caruso, G.J.

1987-01-01

A summary of the 'Identification and selection of starting events' stage of the previous probabilistic safety evaluation of RA-6 reactor is presented. This evaluation was performed to verify if the safety criteria required for the licensing of RA-6 are met and to promote the diffusion of its meaning and usefulness with educational purposes. At this stage the starting events of RA-6 are determined and the probability that such events occur is calculated. The identification and selection of starting events is performed in two steps: determination of proposed starting events and determination of postulated starting events. The proposed starting events are determined by means of the master logic diagram (MLD) method, while the postulated starting events are obtained by grouping the proposed starting events. The simplifying hypothesis required for the application of MLD to the reactor are also formulated. The probability that the proposed and postulated starting events occur is afterwards calculated, adopting different fault models, in accordance with the nature of events that are considered. Conservative hypothesis on the characteristics of these events and the uncertainty of parameter values of those models are also formulated. The numerical values of the above mentioned probabilities are obtained by giving the parameters suitable values that are extracted from specialized publications. (Author)

Delaying Middle School and High School Start Times Promotes Student Health and Performance: An American Academy of Sleep Medicine Position Statement.

Science.gov (United States)

Watson, Nathaniel F; Martin, Jennifer L; Wise, Merrill S; Carden, Kelly A; Kirsch, Douglas B; Kristo, David A; Malhotra, Raman K; Olson, Eric J; Ramar, Kannan; Rosen, Ilene M; Rowley, James A; Weaver, Terri E; Chervin, Ronald D

2017-04-15

During adolescence, internal circadian rhythms and biological sleep drive change to result in later sleep and wake times. As a result of these changes, early middle school and high school start times curtail sleep, hamper a student's preparedness to learn, negatively impact physical and mental health, and impair driving safety. Furthermore, a growing body of evidence shows that delaying school start times positively impacts student achievement, health, and safety. Public awareness of the hazards of early school start times and the benefits of later start times are largely unappreciated. As a result, the American Academy of Sleep Medicine is calling on communities, school boards, and educational institutions to implement start times of 8:30 AM or later for middle schools and high schools to ensure that every student arrives at school healthy, awake, alert, and ready to learn. © 2017 American Academy of Sleep Medicine

Analytic method study of point-reactor kinetic equation when cold start-up

International Nuclear Information System (INIS)

Zhang Fan; Chen Wenzhen; Gui Xuewen

2008-01-01

The reactor cold start-up is a process of inserting reactivity by lifting control rod discontinuously. Inserting too much reactivity will cause short-period and may cause an overpressure accident in the primary loop. It is therefore very important to understand the rule of neutron density variation and to find out the relationships among the speed of lifting control rod, and the duration and speed of neutron density response. It is also helpful for the operators to grasp the rule in order to avoid a start-up accident. This paper starts with one-group delayed neutron point-reactor kinetics equations and provides their analytic solution when reactivity is introduced by lifting control rods discontinuously. The analytic expression is validated by comparison with practical data. It is shown that the analytic solution agrees well with numerical solution. Using this analytical solution, the relationships among neutron density response with the speed of lifting control rod and its duration are also studied. By comparing the results with those under the condition of step inserted reactivity, useful conclusions are drawn

A novel transient wall heat transfer approach for the start-up of SI engines with gasoline direct injection

Science.gov (United States)

Lejsek, David; Kulzer, André; Hammer, Jürgen

2010-11-01

The introduction of CO2-reduction technologies like Start-Stop or the Hybrid-Powertrain and the worldwide stringent emission legislation require a detailed optimization of the engine start-up. The combustion concept development as well as the calibration of the engine control unit makes an explicit thermodynamic analysis of the combustion process during the start-up necessary. Initially, the well-known thermodynamic analysis of in-cylinder pressure at stationary condition was transmitted to the highly non-stationary engine start-up. For this running mode of the engine the current models for calculation of the transient wall heat fluxes were found to be misleading. With a fraction of nearly 45% of the burned fuel energy, the wall heat is very important for the calculation of energy balance and for the combustion process analysis. Based on the measurements of transient wall heat transfer densities during the start-up presented in a former work (Lejsek and Kulzer in Investigations on the transient wall heat transfer at start-up for SI engines with gasoline direct injection. SAE Paper), the paper describes the development of adaptations to the known correlations by Woschni (MTZ 31:491, 1970), Hohenberg (Experimentelle Erfassung der Wandwärme von Kolbenmotoren. TU Graz, Habil., 1980) and Bargende (Ein Gleichungsansatz zur Berechnung der instationären Wandwärmeverluste im Hochdruckteil von Ottomotoren. TH Darmstadt, PhD-Thesis, 1991) for the application during engine start-up. To demonstrate the high accuracy of the model, the results of the cyclic resolved thermodynamic analysis using the presented novel approaches were compared with the results of the measurements. It is shown, that the novel heat flux models for the engine start-up process gives a cyclic resolved thermodynamic analysis to optimize the engine start-up pretty efficient.

A Healthy Start Can Begin Now

Science.gov (United States)

A healthy pregnancy begins before you ever become pregnant. Give yourself the best chance for a healthy pregnancy and healthy baby before you start down the road to motherhood. If you smoke, now’s a great time to quit.

An eigenexpansion technique for modelling plasma start-up

International Nuclear Information System (INIS)

Pillsbury, R.D.

1989-01-01

An algorithm has been developed and implemented in a computer program that allows the estimation of PF coil voltages required to start-up an axisymmetric plasma in a tokamak in the presence of eddy currents in toroidally continuous conducting structures. The algorithm makes use of an eigen-expansion technique to solve the lumped parameter circuit loop voltage equations associated with the PF coils and passive (conducting) structures. An example of start-up for CIT (Compact Ignition Tokamak) is included

Simulations and field tests of a reactor coolant pump emergency start-up by means of remote gas units

International Nuclear Information System (INIS)

Omahen, P.; Gubina, F.

1992-01-01

The problem of the reactor coolant pump start-up in case of emergency by means of remote gas power plant units was analyzed. In this paper a simulation model is developed which enabled a detailed simulation of the transient process occurring at the start-up. The start-up of the RCP motor set was simulated in case of available one and two gas units. The field tests were performed and the measured variable values complied well with the simulation results. Two gas units have been determined as a safe start-up scheme of the RCP motor set considering for safety reasons accepted busbars and motor protection settings. A derived model for deep rotor bars was experimentally confirmed as effective means for the RCP motor set start-up transient simulation. Start-up procedures have been designed and adopted to the safety procedures of the Nuclear Power Plant Krsko

The study of transient processes in the asynchronous starting of the synchronous motor

OpenAIRE

Alexandru Bârlea; Olivian Chiver

2012-01-01

Starting synchronous motors can be achieved by several ethods: starting with an auxiliary motor launch, starting in asynchronous regim, by feeding from a variable frequency source, auto-synchronization with the network.. In our case we study the transient processes in a asynchronous regim . In this case the synchronous motor is started like a squirrel cage induction motor . To start, the synchronous motor is equipped with a starting winding cage placed in the pole pieces of polar inducers; la...

Dynamics and Control During Start-up of Energy Integrated Distillation Column

DEFF Research Database (Denmark)

Eden, Mario Richard; Koggersbøl, Arne; Hallager, L.

2000-01-01

of the inherent effects of process integration upon a start-up procedure. In particular the effect of energy recycle upon the possible start-up sequence, and the effect of using an actuator f or control purposes, i.e. the heat pump, which in itself requires significant start-up time. The experimental application...

78 FR 73753 - Partnerships; Start-Up Expenditures; Organization and Syndication Fees

Science.gov (United States)

2013-12-09

... deduct start-up expenditures in the taxable year in which the active trade or business begins. The amount... begins. All start-up expenditures that relate to the active trade or business are considered in...(b) to amortize start-up expenditures for the taxable year in which the active trade or business to...

Fuel conditioning facility electrorefiner start-up results

International Nuclear Information System (INIS)

Goff, K.M.; Mariani, R.D.; Vaden, D.; Bonomo, N.L.; Cunningham, S.S.

1996-01-01

At ANL-West, there are several thousand kilograms of metallic spent nuclear fuel containing bond sodium. This fuel will be treated in the Fuel Conditioning Facility (FCF) at ANL-West to produce stable waste forms for storage and disposal. The treatment operations will make use of an electrometallurgical process employing molten salts and liquid metals. The treatment equipment is presently undergoing testing with depleted uranium. Operations with irradiated fuel will commence when the environmental evaluation for FCF is complete

Engine cold start analysis using naturalistic driving data: City level impacts on local pollutants emissions and energy consumption.

Science.gov (United States)

Faria, Marta V; Varella, Roberto A; Duarte, Gonçalo O; Farias, Tiago L; Baptista, Patrícia C

2018-07-15

The analysis of vehicle cold start emissions has become an issue of utmost importance since the cold phase occurs mainly in urban context, where most of the population lives. In this sense, this research work analyzes and quantifies the impacts of cold start in urban context using naturalistic driving data. Furthermore, an assessment of the influence of ambient temperature on the percentage of time spent on cold start was also performed. Regarding the impacts of ambient temperature on cold start duration, a higher percentage of time spent on cold start was found for lower ambient temperatures (80% of the time for 0°C and ~50% for 29°C). Results showed that, during cold start, energy consumption is >110% higher than during hot conditions while emissions are up to 910% higher. Moreover, a higher increase on both energy consumption and emissions was found for gasoline vehicles than for diesel vehicles. When assessing the impacts on a city perspective, results revealed that the impacts of cold start increase for more local streets. The main finding of this study is to provide evidence that a higher increase on emissions occurs on more local streets, where most of the population lives. This kind of knowledge is of particular relevance to urban planners in order to perform an informed definition of public policies and regulations to be implemented in the future, to achieve a cleaner and healthier urban environment. Copyright © 2018 Elsevier B.V. All rights reserved.

Development of data processing system for the start-up test of FUGEN

International Nuclear Information System (INIS)

Nakajima, Ichiro; Kato, Hidemasa

1981-01-01

The data processing in the start-up test of conventional reactors has been carried out by recording data with transient phenomena recorders (e.g. electromagnetic oscillographs) or analog data recorders. On the other hand, the rapid works for detailed comparison and investigation between the test data and the analyzed results have been indispensable because ''Fugen'' is a new type of reactor, for which the results in conventional reactors did not necessarily serve as reference. Therefore, in the start-up test of the ''Fugen'' plant, the test data processing and the forecast analysis were performed by installing on the site a mini-computer capable of independently processing the test data and a terminal equipment connected to a large computer with a special communication line. As soon as the testing was completed, the comparison of the test data with the forecast analysis was presented on a graphic display (CRT), and the analysis was modified until significant differences did not appear between the test data and the analyzed data. In this paper, the system hardware and software are described, and two functions of forecast analysis and test data processing are explained. The time required for printing-out or graphic display from inputting 600 kB analysis code data using the terminal equipment was 10 to 30 minutes, and the evaluation and investigation for the test results were able to be immediately achieved by the data processing using the mini-computer. This is one of the factors to carry out the start-up test satisfactorily together with the forecast analysis works. (Wakatsuki, Y.)

Producing an Assistant Guide for Haaga-Helia StartUp School

OpenAIRE

Averina, Maria

2016-01-01

This product-oriented thesis was commissioned by the StartUp School (SUS), a program of Haaga-Helia University of Applied Sciences that supports Haaga-Helia students to become entrepreneurs. The StartUp School offers Haaga-Helia students a six-month assistant trainee position. Consequently, every half a year there is a new assistant at the StartUp School. The commissioning party was lacking an essential tool to introduce work tasks to new assistant interns. The objective of the thesis was...

Automatic start-up system of nuclear reactor based on sequence control technology

International Nuclear Information System (INIS)

Zhang Yao; Zhang Dafa; Peng Huaqing

2009-01-01

A conceptive design of an automatic start-up system based on the sequence control for the nuclear reactors is given in this paper, so as to solve the problems during the start-up process, such as the long operation time, low automatic control level and high accident rate. The start-up process and its requirements are analyzed in detail at first. Then,the principle, the architecture, the key technologies of the automatic start-up system of nuclear reactors are designed and discussed. With the designed system, the automatic start-up of the nuclear reactor can be realized,the work load of the operator can be reduced,and the safety and efficiency of the nuclear power plant during its start-up can be improved. (authors)

Emerging Themes and Lessons Learned: The First Year of Smart Start.

Science.gov (United States)

Maxwell, Kelly; Bryant, Donna; Adkins, Amee; McCadden, Brian; Noblit, George

Smart Start is North Carolina's partnership between state government and local leaders, service providers, and families to better serve children under 6 years of age and their families. A formative evaluation of the Smart Start process, to inform the current state-level decision-making processes for future Smart Start efforts, was devised from a…

Quantifying Variation in Head Start Effects on Young Children's Cognitive and Socio-Emotional Skills Using Data from the National Head Start Impact Study

Science.gov (United States)

Bloom, Howard S.; Weiland, Christina

2015-01-01

This paper uses data from the Head Start Impact Study (HSIS), a nationally representative multisite randomized trial, to quantify variation in effects of Head Start during 2002-2003 on children's cognitive and socio-emotional outcomes relative to the effects of other local alternatives, including parent care. We find that (1) treatment and control…

Small Vertical Axis Wind Turbines: aerodynamics and starting behavior

Directory of Open Access Journals (Sweden)

Horia DUMITRESCU

2013-12-01

Full Text Available In urban areas the wind is very turbulent and unstable with fast changes in direction andvelocity. In these environments, the use of small vertical axis wind turbines (VAWT becomesincreasingly attractive due to several advantages over horizontal axis wind turbines (HAWT.However, such designs have received much less attention than the more common propeller-typedesigns and the understanding of same aspects of their operation remains, to this day, incomplete.This is particularly true of their starting characteristics. Indeed, same authors heuristically maintainthat they cannot start without external assistance. This paper reviews the cause of the inability of thelow solidity fixed pitch vertical axis wind turbines to self-start, and investigates the way ofovercoming this draw back.

Getting started with Arduino

CERN Document Server

Banzi, Massimo

2011-01-01

Arduino is the open-source electronics prototyping platform that's taken the design and hobbyist world by storm. This thorough introduction, updated for Arduino 1.0, gives you lots of ideas for projects and helps you work with them right away. From getting organized to putting the final touches on your prototype, all the information you need is here! Inside, you'll learn about: Interaction design and physical computingThe Arduino hardware and software development environmentBasics of electricity and electronicsPrototyping on a solderless breadboardDrawing a schematic diagram Getting started

Getting Started with Netduino

CERN Document Server

Walker, Chris

2012-01-01

Start building electronics projects with Netduino, the popular open source hardware platform that's captured the imagination of makers and hobbyists worldwide. This easy-to-follow book provides the step-by-step guidance you need to experiment with Netduino and the .NET Micro Framework. Through a set of simple projects, you'll learn how to create electronic gadgets-including networked devices that communicate over TCP/IP. Along the way, hobbyists will pick up the basics of .NET programming, and programmers will discover how to work with electronics and microcontrollers. Follow the projects in

Do Specific Growth Drivers Exist for Firms? A Regional Analysis of Start-ups and Industrial Growth

Directory of Open Access Journals (Sweden)

PAUL I. OJEAGA

2016-06-01

Full Text Available The study of start-ups, have remained largely a micro economic issue. Firms are the key drivers of industrial sector GDP (or enterprise growth in countries across regions. Few studies have tried to examine the consequence of start-ups in the broad macroeconomics terms on enterprise growth in general with special emphasis on industrial sector output. This study provides a macroeconomic study of the effect of start- ups on industrial sector growth for countries in some specific geographical regions of the world. Panel data is utilized due to it obvious advantages such its ability to utilize a panel of short time frames and its suitability for controlling for omitted variable bias and unobservable heterogeneity across regions. The results show that start-ups remain an intrinsic variable for enterprise growth and industrial sector output discussion in general.

Relationship Between Vertical Jump Height and Swimming Start Performance Before and After an Altitude Training Camp.

Science.gov (United States)

García-Ramos, Amador; Padial, Paulino; de la Fuente, Blanca; Argüelles-Cienfuegos, Javier; Bonitch-Góngora, Juan; Feriche, Belén

2016-06-01

This study aimed (a) to analyze the development in the squat jump height and swimming start performance after an altitude training camp, (b) to correlate the jump height and swimming start performance before and after the altitude training period, and (c) to correlate the percent change in the squat jump height with the percent change in swimming start performance. Fifteen elite male swimmers from the Spanish Junior National Team (17.1 ± 0.8 years) were tested before and after a 17-day training camp at moderate altitude. The height reached in the squat jump exercise with additional loads of 0, 25, 50, 75, and 100% of swimmers' pretest body weight and swimming start performance (time to 5, 10, and 15 m) were the dependent variables analyzed. Significant increases in the jump height (p ≤ 0.05; effect size [ES]: 0.35-0.48) and swimming start performance (p jump height before training (r = -0.56 to -0.77) and after training (r = -0.50 to -0.71). The change in the squat jump height was inversely correlated with the change in the start time at 5 m (r = -0.47), 10 m (r = -0.73), and 15 m (r = -0.62). These results suggest that altitude training can be suitable to enhance explosive performance. The correlations obtained between the squat jump height and start time in the raw and change scores confirm the relevance of having high levels of lower-body muscular power to optimize swimming start performance.

Getting started with MariaDB

CERN Document Server

Bartholomew, Daniel

2013-01-01

A practical, hands-on, beginner-friendly guide to installing and using MariaDB.Getting Started with MariaDB is for anyone who wants to learn more about databases in general or MariaDB in particular. No prior database experience is required. It is assumed that you have basic knowledge of software installation, editing files with a text editor, and using the command line and terminal.

A novel dimmable LED driver with soft-start and UVLO circuits

International Nuclear Information System (INIS)

Jiang Jinguang; Tan Gaojian; Zhou Xifeng; Zhang Zeyu

2015-01-01

A fully integrated LED driver based on a current mode PWM boost DC—DC converter with constant output current is proposed. In order to suppress the inrush of current and the overshoot voltage at the start up state, a soft-start circuit is adopted. Additionally, to adjust the LED brightness without color variation over the full dimming range and achieve high efficiency, a PWM dimming circuit is presented. Furthermore, to keep the loop stability of the LED driver, an internal slope compensation network is designed to avoid the sub-harmonic oscillation when the duty cycle exceeds 50%. Finally, a UVLO circuit is adopted to improve the reliability of the LED driver against the input voltage changing. The LED driver has been fabricated with a standard 0.5 μm CMOS process, and only occupies 1.21 × 0.76 mm 2 . Experimental results show that the brightness of the LED can be adjusted by an off-chip PWM signal with a wide adjusting range. The inductor current and output current increase smoothly over the whole load range. The chip is in the UVLO condition when the input voltage is below 2.18 V and has achieved about 137 μs typical start-up time. (semiconductor integrated circuits)

Baikal-1 stand complex. Preparation and carrying out of the first energy start-up of the IVG-1 reactor

International Nuclear Information System (INIS)

Tikhomirov, L.N.

1995-01-01

The IVG-1 reactor was a first ground prototype of nuclear rocket engine. The reactor was built on the site 10 of the Semipalatinsk test site. Since the first energy start-up in 1975 the reactor was exploited 14 years till its modernization in 1989. The Bajkal-1 stand complex was designed and built for the carrying out of tests for fuel assemblies of different modifications. The energy start-up has been sum of long creative work of different research and constructive staffs on creation of high-temperature gas-cooled IVG-1 reactor. The history of construction, project and assembling of the stand complex is presented. Complex start and put works were carried out in the December 1974. Control physical start-up was carried out in the January 1975. Cold start-up by hydrogen was in the February 1975. Hot start-up was in the March 1975. The result of the hot start-up was experimental confirmation of metodics of thermohydrovlical estimations. 2 figs., 3 tabs

Ensemble approach combining multiple methods improves human transcription start site prediction.

LENUS (Irish Health Repository)

Dineen, David G

2010-01-01

The computational prediction of transcription start sites is an important unsolved problem. Some recent progress has been made, but many promoters, particularly those not associated with CpG islands, are still difficult to locate using current methods. These methods use different features and training sets, along with a variety of machine learning techniques and result in different prediction sets.

Established Companies meet Start-ups : Case: A service to research developing business models in start-up hot spots around the globe

OpenAIRE

Eisenblätter, Simon

2016-01-01

This thesis presents a business model with the aim to improve conversation between traditional companies and newly established start-ups. The assumption that such conversation can be facilitated by scouting for innovation in start-up hot spots around the world, will be discussed throughout the paper. The purpose of this work is to lay out a plan which can be presented to a first range of possible customers, with the goal of negotiating a trial cooperation. Before introducing the busi...

The Effect of Previous Co-Worker Experience on the Survival of Knowledge Intensive Start-Ups

DEFF Research Database (Denmark)

Timmermans, Bram

The aim of the paper is to investigate the effect of previous co-worker experience on the survival of knowledge intensive start-ups. For the empirical analysis I use the Danish Integrated Database of Labor Market Research (IDA). This longitudinal employer-employee database allows me to identify co-worker...... experience among all members of the firm. In addition, I will make a distinction between ordinary start-ups and entrepreneurial spin-offs. The results show that previous co-worker experience has a positive effect on new firm survival. This effect appears to be valid predominantly for ordinary start-ups than...

Start-up of commercial high level waste vitrification facilities at La Hague

International Nuclear Information System (INIS)

Sombret, C.; Jouan, A.; Fournier, W.; Alexandre, D.; Leroy, L.

1991-01-01

The paper describes industial experience gained in France for vitrification of fission products generated by spent fuel reprocessing. The continuous vitrification process developed by CEA, SGN and COGEMA is outlined and Marcoule Vitrification Facility (AVM), with output results since start-up of hot operation in June 1978, briefly presented. Vitrification of high-level liquid waste has now entered an industrial phase at La Hague with R7 and T7 facilities. R7 and T7 have each been designed to process FP solutions generated by reprocessing LWR fuel with an initial enrichment of 3.5% and a discharge burn-up of 33,000 MWd/t. R7 active operations began on June, 1989. This facility is now vitrifying the backlog of fission products resulting from the existing UP2 reprocessing plant, which is being currently extended. Scheduled to start early in 1992, T7 will vitrify the fission products, dissolution fines and sodium-rich solutions issuing from UP3 plant

Getting started with SQL Server 2012 cube development

CERN Document Server

Lidberg, Simon

2013-01-01

As a practical tutorial for Analysis Services, get started with developing cubes. ""Getting Started with SQL Server 2012 Cube Development"" walks you through the basics, working with SSAS to build cubes and get them up and running.Written for SQL Server developers who have not previously worked with Analysis Services. It is assumed that you have experience with relational databases, but no prior knowledge of cube development is required. You need SQL Server 2012 in order to follow along with the exercises in this book.

Both bias and lack of knowledge influence organizational focus on first case of the day starts.

Science.gov (United States)

Dexter, Elisabeth U; Dexter, Franklin; Masursky, Danielle; Garver, Michael P; Nussmeier, Nancy A

2009-04-01

The economic costs of reducing first case delays are often high, because efforts need to be applied to multiple operating rooms (ORs) simultaneously. Nevertheless, delays in starting first cases of the day are a common topic in OR committee meetings. We added three scientific questions to a 24 question online, anonymous survey performed before the implementation of a new OR information system. The 57 respondents cared sufficiently about OR management at the United States teaching hospital to complete all questions. The survey revealed reasons why personnel may focus on the small reductions in nonoperative time achievable by reducing tardiness in first cases of the day. (A) Respondents lacked knowledge about principles in reducing over-utilized OR time to increase OR efficiency, based on their answering the relevant question correctly at a rate no different from guessing at random. Those results differed from prior findings of responses at a rate worse than random, resulting from a bias on the day of surgery of making decisions that increase clinical work per unit time. (B) Most respondents falsely believed that a 10 min delay at the start of the day causes subsequent cases to start at least 10 min late (P less time than scheduled (P = 0.008 versus chance). No one who demonstrated knowledge (C) about cases sometimes taking less time than scheduled applied that information to their response to (B) regarding cases starting late (P = 0.0002). Knowledge of OR efficiency was low among the respondents working in ORs. Nevertheless, the apparent absence of bias shows that education may influence behavior. In contrast, presence of bias on matters of tardiness of start times shows that education may be of no benefit. As the latter results match findings of previous studies of scheduling decisions, interventions to reduce patient and surgeon waiting from start times may depend principally on the application of automation to guide decision-making.

Starting Up a Company in a Mature Market: Wise or Foolish ?

Science.gov (United States)

Biberger, Maximilian

SDCmaterials, Inc. (SDC) is a venture backed, mature start up in the automotive sector. Moreover: Catalytic Converters for vehicles and stationary applications. The company has invented and developed environmentally friendly, novel materials as well as material integration techniques for catalytic converters based on a proprietary and patented nanotechnology. Traditionally catalysts require large amounts of PGMs (Platinum Group Metals), more than USD 10B per year, in order to treat vehicle emissions. Due to that, the catalytic converter is the single most expensive piece part in a vehicle. The currently used technologies have served the industry well. However, as emission standards dramatically tighten, particularly in China, the demand for more fuel efficient and Hybrid vehicles increases, this technology begins to start showing limitations as it can meet the aforementioned demands only by increasing the PGM amount per vehicle. This in turn will increase the cost per vehicle and / or reduce margins for the automotive industry, and in addition to that impact the environment negatively. In contrast to existing technologies, the SDC based technology can meet future emission goals by maintaining, or even reducing, the PGM amount required to treat exhaust emissions. This results in tremendous savings for the consumer and the automotive industry, as well as a significantly better stewardship of natural resources and clean manufacturing. In the present paper the pros and cons of starting a nanotechnology company in a mature market are presented. Both from a business & economics, as well as from a technology point of view. The case is made that it is possible to start a company in a mature market and that novel technologies can compete economically with 40+ old year technologies.

Monitoring Start of Season in Alaska

Science.gov (United States)

Robin, J.; Dubayah, R.; Sparrow, E.; Levine, E.

2006-12-01

In biomes that have distinct winter seasons, start of spring phenological events, specifically timing of budburst and green-up of leaves, coincides with transpiration. Seasons leave annual signatures that reflect the dynamic nature of the hydrologic cycle and link the different spheres of the Earth system. This paper evaluates whether continuity between AVHRR and MODIS normalized difference vegetation index (NDVI) is achievable for monitoring land surface phenology, specifically start of season (SOS), in Alaska. Additionally, two thresholds, one based on NDVI and the other on accumulated growing degree-days (GDD), are compared to determine which most accurately predicts SOS for Fairbanks. Ratio of maximum greenness at SOS was computed from biweekly AVHRR and MODIS composites for 2001 through 2004 for Anchorage and Fairbanks regions. SOS dates were determined from annual green-up observations made by GLOBE students. Results showed that different processing as well as spectral characteristics of each sensor restrict continuity between the two datasets. MODIS values were consistently higher and had less inter-annual variability during the height of the growing season than corresponding AVHRR values. Furthermore, a threshold of 131-175 accumulated GDD was a better predictor of SOS for Fairbanks than a NDVI threshold applied to AVHRR and MODIS datasets. The NDVI threshold was developed from biweekly AVHRR composites from 1982 through 2004 and corresponding annual green-up observations at University of Alaska-Fairbanks (UAF). The GDD threshold was developed from 20+ years of historic daily mean air temperature data and the same green-up observations. SOS dates computed with the GDD threshold most closely resembled actual green-up dates observed by GLOBE students and UAF researchers. Overall, biweekly composites and effects of clouds, snow, and conifers limit the ability of NDVI to monitor phenological changes in Alaska.

Hydrogen energy network start-up scenario

International Nuclear Information System (INIS)

Weingartner, S.; Ellerbrock, H.

1994-01-01

Hydrogen is widely discussed as future fuel and energy storage medium either to replace conventional fuels for automobiles, aircrafts and ships or to avoid the necessity of bulky battery systems for electricity storage, especially in connection with solar power systems. These discussions however started more than 25 years ago and up to now hydrogen has failed to achieve a major break-through towards wider application as energy storage medium in civil markets. The main reason is that other fuels are cheaper and very well implemented in our daily life. A study has been performed at Deutsche Aerospace in order to evaluate the boundary conditions, either political or economical, which would give hydrogen the necessary push, i.e. advantage over conventional fuels. The main goal of this study was to identify critical influence factors and specific start-up scenarios which would allow an economical and practically realistic use of hydrogen as fuel and energy medium in certain niche markets outside the space industry. Method and major results of this study are presented in detail in the paper. Certain niche markets could be identified, where with little initial governmental support, either by funding, tax laws or legislation, hydrogen can compete with conventional fuels. This however requires a scenario where a lot of small actions have to be taken by a high variety of institutions and industries which today are not interconnected with each other, i.e. it requires a new cooperative and proactive network between e.g. energy utilities, car industries, those who have a sound experience with hydrogen (space industry, chemical industry) and last, but certainly not the least, the government. Based on the developed scenario precise recommendations are drawn as conclusions

Starting-up sequence of the AWEC-60 wind turbine

International Nuclear Information System (INIS)

Avia, F.; Cruz, M. de la.

1991-01-01

One of the most critical status of the wind turbines operation is the starting-up sequence and the connection to the grid, due to the actuating loads that could be several times the loads during operation at rated conditions. Due to this fact, the control strategy is very important during the starting-up sequence in order to minimize the loads on the machine. For this purpose it is necessary to analyze the behaviour of the wind turbine during that sequence in different wind conditions and machine conditions. This report shows the graphic information about fifty starting-up sequences of the AWEC-60 wind turbine of 60 m. diameter and 1200 kW of rated power, recorded in April 1991 and cut-out wind speed. (author)

Start-up conditions and the performance of women - and men - controlled businesses in manufacturing industries

Directory of Open Access Journals (Sweden)

Otilia Driga

2010-01-01

Full Text Available Recent research into the economic performance of women-controlled firms suggests that their underperformance may not be the result of differences in the managerial ability of women as compared to men, and that it may in fact be a consequence of differing levels of start-up resources. Using accounting data, we examine the effects that selected start-up conditions have had on the observed economic performance of a sample of 4450 Spanish manufacturing firms. The results, which indicate significant differences in the initial conditions and show lower levels of assets and employee numbers in women-controlled firms, have implications for the economic performance of such firms.

Practical Considerations of the Start-up Procedure for an Active Capacitor

DEFF Research Database (Denmark)

Wang, Haoran; Wang, Qian; Geng, Tao

2017-01-01

Capacitive DC links provide the only low-impedance current path connected with an input source during the start-up of many voltage source converters. A soft-start circuit is usually implemented to limit the inrush current. A two-terminal active capacitor is recently proposed which can directly...... replace conventional passive capacitors in DC links, with reduced cost or size for a given application. The active capacitor has the same level of convenience with two power terminals only as a passive capacitor. This paper proposes two start-up schemes for the active capacitor to overcome the drawbacks...... of existing methods previously widely used for passive capacitors. One scheme is based on a trade-off design between the start-up performance and the component sizing of the active capacitor. The other scheme is based on either an additional bypass switch together with the existing soft-start circuit...

School Start Time and Teen Sleep.

Science.gov (United States)

Wahlstrom, Kyla L.

2000-01-01

Sleep studies have shown that teenagers' internal clocks are incompatible with most high schools' early hours. Research in two Minnesota districts indicates that later school starting times can benefit teens and everyone dealing with them. Student participation in sports and other afterschool activities remained high. (MLH)

Getting started with Magento module development

CERN Document Server

Ajzele, Branko

2013-01-01

This project-based tutorial gives you a strong foundation and guides you through practical, real-world examples.This book contains valuable insights for both newbies and already established Magento developers. This book is targeted at new and intermediate PHP developers starting afresh with Magento module development.

Start of the international tokamak physics activity

International Nuclear Information System (INIS)

Campbell, D.

2001-01-01

This newsletter comprises a summary on the start of the International Tokamak Physics activity (ITPA) by Dr. D. Campbell, Chair of the ITPA Co-ordinating Committee. As the ITER EDA drew to a close, it became clear that it was desirable to establish a new mechanism in order to promote the continued development of the physics basis for burning plasma experiments and to preserve the invaluable collaborations between the major international fusion communities which had been established through the ITER physics expert groups. As a result of the discussions of the representatives of the European Union, Japan, the Russian Federation and the United States the agreed principles for conducting the International Tokamak Physics Activity (ITPA) were elaborated and ITPA topical physics groups were organized

Where Does Originality End and Plagiarism Start? Discussing Plagiarism in Information Science

DEFF Research Database (Denmark)

Greifeneder, Elke Susanne; Connaway, Lynn Silipigni; Jiang, Tingting

2014-01-01

no longer be considered to be original and starts to be considered self-plagiarism. Parts of the discussion will center on the question of whether information science researchers can actually avoid repeating the same words when today they have to publish results from research projects in as many...

Giving start-ups a helping hand

CERN Multimedia

2008-01-01

The French-Swiss foundation for research and technology (FFSRT) joined forces with CERN to organise an information day on setting up new businesses, at the Globe of Science and Innovation. The participants heard talks by entrepreneurs who started out at CERN, sharing their experiences and difficulties.CERN is a hot-bed of high-tech skills and know-how, and the Organization works actively to transfer this expertise to society. Some such innovations can lead to new business start-ups, but it can be extremely difficult to obtain the information and support you need to find your way through the inevitable administrative labyrinth. By opening its doors to the Fondation franco-suisse pour la recherche et la technologie (FFSRT) and hosting this "Entrepreneurial Day" on 7 March, CERN has clearly flagged its desire to assist budding entrepreneurs. The day was jointly kicked off by Olga Hooft, General Manager of the FFSRT, and Maximilian Metzger, CERN’s Se...

Getting started with nopCommerce

CERN Document Server

Atkinson, Brandon

2013-01-01

A friendly, tutorial style book, which will help you learn your way through creating a live storefront with nopCommerce in a step-by-step manner.Getting Started with nopCommerce is for anyone who wants to sell products online using nopCommerce. If you are a non-technical person and are discouraged by the complexity of this powerful e-commerce application, then this book is for you.

Getting started with Twitter Flight

CERN Document Server

Hamshere, Tom

2013-01-01

Getting Started with Twitter Flight is written with the intention to educate the readers, helping them learn how to build modular powerful applications with Flight, Twitter's cutting-edge JavaScript framework.This book is for anyone with a foundation in JavaScript who wants to build web applications. Flight is quick and easy to learn, built on technologies you already understand such as the DOM, events, and jQuery.

High-inertia drive motors and their starting characteristics

International Nuclear Information System (INIS)

Anon.

1980-01-01

The motor for a large reactor coolant pump failed while starting. The motor-application and the motor-failure are discussed in detail. A review of applications of motors for high-inertia drives shows that a motor designed and built to today's industry-standards might be overstressed while experiencing abnormal starting conditions, even though its protection is in accord with accepted practice. The inter-relationship between motor characteristics and characteristics of various types of protection are discussed, briefly. The review concludes that motor specifications and motor standards should be augmented. 1 ref

Getting Started with Processing

CERN Document Server

Reas, Casey

2010-01-01

Learn computer programming the easy way with Processing, a simple language that lets you use code to create drawings, animation, and interactive graphics. Programming courses usually start with theory, but this book lets you jump right into creative and fun projects. It's ideal for anyone who wants to learn basic programming, and serves as a simple introduction to graphics for people with some programming skills. Written by the founders of Processing, this book takes you through the learning process one step at a time to help you grasp core programming concepts. You'll learn how to sketch wi

The Written-Pole{sup TM} motor: high efficiency - low start current

Energy Technology Data Exchange (ETDEWEB)

Beck, B. [C.Eng. Precise Power Corp., Bradenton, FL (United States); Friesen, D. [P.E. Manitoba Hydro, Winnipeg (Canada)

2000-07-01

Written-Pole{sup TM} technology is a patented machine technology, which changes the magnetic polarity of the rotor field in a rotating machine, while the machine is operating. The number of poles is thereby changed, resulting in a constant frequency - variable speed machine. When operating as a motor, a Written-Pole machine has inherently low starting current and high operating efficiency. (orig.)

Determination of interplanar distances starting from diffraction spectra for PC microcomputer

International Nuclear Information System (INIS)

Macias B, L.R.

1991-07-01

The objective of this work, consists in that starting of a digitized diffraction spectra result of the structural analysis technique, it is possible by means of the analysis of a computer program, to detect the diffraction peaks and well-known the wavelength to obtain the values of the interplanar distances to be compared with the JCPDS (Joint Committee on Powder Diffraction Standards). (Author)

START to Get Ready for Breastfeeding

Science.gov (United States)

Breastfeeding is a great way to give your baby the nutrients he or she needs to grow and develop. Breastfeeding also can help you and your baby form a special bond. Breastfeeding can be good for both of you if you know where to S-T-A-R-T.

Caregivers' attitudes regarding portion size served to Head Start children

Science.gov (United States)

The purpose of this study was to identify caregivers' attitudes regarding amounts and types of foods served to Head Start preschoolers using qualitative methods. Researchers conducted 8 focus groups (4 African American; 4 Hispanic) with 33 African American and 29 Hispanic Head Start caregivers. Mode...

Improving NPT safeguards. Particularly at the natural uranium starting point

International Nuclear Information System (INIS)

Harry, J.; Klerk, P. de

1996-03-01

According to the Non Proliferation Treaty (NPT) all nuclear material is subject to safeguards, but according to INFCIRC/153 the full range of safeguards is only applied beyond the 'starting point of safeguards', that is: The point at which nuclear material has reached a composition and purity suitable for fuel fabrication or enrichment. This paper addresses the two questions: (a) is the starting point adequately defined, and (b) what mesures could be applied to nuclear material before the starting point? Those questions have been asked before, some of the answers in this paper are new. (orig.)

Improving NPT safeguards. Particularly at the natural uranium starting point

Energy Technology Data Exchange (ETDEWEB)

Harry, J. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Klerk, P. de [Ministry of Foreign Affairs, The Hague (Netherlands)

1996-03-01

According to the Non Proliferation Treaty (NPT) all nuclear material is subject to safeguards, but according to INFCIRC/153 the full range of safeguards is only applied beyond the `starting point of safeguards`, that is: The point at which nuclear material has reached a composition and purity suitable for fuel fabrication or enrichment. This paper addresses the two questions: (a) is the starting point adequately defined, and (b) what mesures could be applied to nuclear material before the starting point? Those questions have been asked before, some of the answers in this paper are new. (orig.).

The Experiment Study of Anaerobic Ammonia Oxidation Start-up by Using the Upflow Double Layer Anaerobic Filter

Directory of Open Access Journals (Sweden)

YAO Li

2018-02-01

Full Text Available Anammox is an efficient nitrogen removal process, but it is difficult to start-up and operate, and ananammox reactor is the efficient way to resolve this problem. The start-up of anammox reactor by upflow anaerobic filter was studied. Denitrifying sludge, anaerobic sludge, and mixed sludge was inoculated on the packing materials, respectively and an autotrophic denitrification condition was provided by the simulated wastewater influent. Along with the gradual increase of matrix concentration and hydraulic load, the microflora was converted to the anaerobic ammonium oxidation(anammoxreaction. The results showed that the anammox reaction could be started by all the three sludge, and the time of start-up of denitrifying sludge, anaerobic sludge, mixed sludge was 42, 54 days and 45 days, respectively. The best result was that inoculated with denitrifying sludge with 82.2% of the total nitrogen removal rate, which started-up quickly and nitrogen was removed efficiently. Double packing effectively improved the stability of anammox process in the reactor, in which the suitable influent concentration loading for the anammox bacteria was 270 mg·L-1 and 360 mg·L-1 for ammonia nitrogen and nitrite nitrogen, respectively, and the COD concentration could not be more than 150 mg· L-1. Furthermore, there was a coexist-effect for anaerobic ammonia oxidation and methanation in this reactor system.

Creating regional consensus for starting school later: a physician-driven approach in southern Maine.

Science.gov (United States)

Collins, Tracey Ann; Indorf, Christopher; Klak, Thomas

2017-12-01

In April 2016, several contiguous school districts and an independent high school academy in southern Maine voted simultaneously to start school later, beginning with the 2016-17 academic year. They became Maine's first school districts to implement the American Academy of Pediatrics' 1 and the American Medical Association's 2 health policy recommendations that middle and high schools should not start before 8:30 AM. Local physicians' presentations to school staff and parents on the medical evidence of the health benefits of a later start solidified early consensus. The action required special permission from the Maine Municipal Association to hold a joint school board vote, impacted approximately 6500 students across the region, resulted in no increase in busing costs, and took 8 months to implement after the first formal school board discussions. Copyright © 2017 National Sleep Foundation. Published by Elsevier Inc. All rights reserved.

Planning and Reviewing for Success. Training Guides for the Head Start Learning Community.

Science.gov (United States)

Aspen Systems Corp., Rockville, MD.

This guide offers Head Start staff a blueprint for developing the skills and methods necessary for a Head Start program's planning and review process. The guide stresses the need for Head Start administrative and managerial leadership to maintain a holistic, integrated approach; use the strength and resources of Head Start team members; identify…

Reasons for starting and stopping electronic cigarette use.

Science.gov (United States)

Pepper, Jessica K; Ribisl, Kurt M; Emery, Sherry L; Brewer, Noel T

2014-10-03

The aim of our study was to explore reasons for starting and then stopping electronic cigarette (e-cigarette) use. Among a national sample of 3878 U.S. adults who reported ever trying e-cigarettes, the most common reasons for trying were curiosity (53%); because a friend or family member used, gave, or offered e-cigarettes (34%); and quitting or reducing smoking (30%). Nearly two-thirds (65%) of people who started using e-cigarettes later stopped using them. Discontinuation was more common among those whose main reason for trying was not goal-oriented (e.g., curiosity) than goal-oriented (e.g., quitting smoking) (81% vs. 45%, p reasons for stopping e-cigarette use were that respondents were just experimenting (49%), using e-cigarettes did not feel like smoking cigarettes (15%), and users did not like the taste (14%). Our results suggest there are two categories of e-cigarette users: those who try for goal-oriented reasons and typically continue using and those who try for non-goal-oriented reasons and then typically stop using. Research should distinguish e-cigarette experimenters from motivated users whose decisions to discontinue relate to the utility or experience of use. Depending on whether e-cigarettes prove to be effective smoking cessation tools or whether they deter cessation, public health programs may need distinct strategies to reach and influence different types of users.

Fundamental study on thermo-hydraulics during start-up in natural circulation boiling water reactors, (1)

International Nuclear Information System (INIS)

Aritomi, Masanori; Chiang Jing-Hsien; Takahashi, Tohru; Wataru, Masumi; Mori, Michitsugu.

1992-01-01

Recently, many concepts, in which passive and simplified functions are actively adapted, have been proposed for the next generation LWRs. The natural circulation BWR is one such considered from the requirements for next generation LWRs as compared with current BWRs. It is pointed out from this consideration that a thermo-hydraulic instability, which may appear during start-up, greatly influences concept feasibility because its occurence makes operation for raising power output difficult. Thermo-hydraulic instabilities are investigated experimentally under conditions simulating normal and abnormal start-up processes. It is clarified that three kinds of thermo-hydraulic instabilities may occur during start-up in the natural circulation BWR according to its procedure and reactor configuration, which are (1) geysering induced by condensation, (2) natural circulation instability induced by hydrostatic head fluctuation in steam separators and (3) density wave instability. Driving mechanisms of the geysering and the natural circulation instability, which have never understood enough, are inferred from the results. Finally, the difference of thermo-hydraulic behavior during start-up processes between thermal natural circulation boilers and the Dodewaard reactor is discussed. (author)

Start-Up Characteristics of a Granule-Based Anammox UASB Reactor Seeded with Anaerobic Granular Sludge

Directory of Open Access Journals (Sweden)

Lei Xiong

2013-01-01

Full Text Available The granulation of anammox sludge plays an important role in the high nitrogen removal performance of the anammox reactor. In this study, anaerobic granular sludge was selected as the seeding sludge to start up anammox reactor in order to directly obtain anammox granules. Results showed that the anammox UASB reactor was successfully started up by inoculating anaerobic granular sludge, with substrate capacity of 4435.2 mg/(L·d and average ammonium and nitrite removal efficiency of 90.36% and 93.29%, respectively. During the start-up course, the granular sludge initially disintegrated and then reaggregated and turned red, suggesting the high anammox performance. Zn-Fe precipitation was observed on the surface of granules during the operation by SEM-EDS, which would impose inhibition to the anammox activity of the granules. Accordingly, it is suggested to relatively reduce the trace metals concentrations, of Fe and Zn in the conventional medium. The findings of this study are expected to be used for a shorter start-up and more stable operation of anammox system.

Start-Up Characteristics of a Granule-Based Anammox UASB Reactor Seeded with Anaerobic Granular Sludge

Science.gov (United States)

Wang, Yun-Yan; Tang, Chong-Jian; Chai, Li-Yuan; Xu, Kang-Que; Song, Yu-Xia

2013-01-01

The granulation of anammox sludge plays an important role in the high nitrogen removal performance of the anammox reactor. In this study, anaerobic granular sludge was selected as the seeding sludge to start up anammox reactor in order to directly obtain anammox granules. Results showed that the anammox UASB reactor was successfully started up by inoculating anaerobic granular sludge, with substrate capacity of 4435.2 mg/(L·d) and average ammonium and nitrite removal efficiency of 90.36% and 93.29%, respectively. During the start-up course, the granular sludge initially disintegrated and then reaggregated and turned red, suggesting the high anammox performance. Zn-Fe precipitation was observed on the surface of granules during the operation by SEM-EDS, which would impose inhibition to the anammox activity of the granules. Accordingly, it is suggested to relatively reduce the trace metals concentrations, of Fe and Zn in the conventional medium. The findings of this study are expected to be used for a shorter start-up and more stable operation of anammox system. PMID:24455691

Spin Start Line Effects on the J2X Gas Generator Chamber Acoustics

Science.gov (United States)

Kenny, R. Jeremy

2011-01-01

The J2X Gas Generator engine design has a spin start line connected near to the turbine inlet vanes. This line provides helium during engine startup to begin turbomachinery operation. The spin start line also acts as an acoustic side branch which alters the chamber's acoustic modes. The side branch effectively creates 'split modes' in the chamber longitudinal modes, in particular below the first longitudinal mode and within the frequency range associated with the injection-coupled response of the Gas Generator. Interaction between the spin start-modified chamber acoustics and the injection-driven response can create a higher system response than without the spin start attached to the chamber. This work reviews the acoustic effects of the spin start line as seen throughout the workhorse gas generator test program. A simple impedance model of the spin start line is reviewed. Tests were run with no initial spin start gas existing in the line, as well as being initially filled with nitrogen gas. Tests were also run with varying spin start line lengths from 0" to 40". Acoustic impedance changes due to different spin start gas constituents and line lengths are shown. Collected thermocouple and static pressure data in the spin start line was used to help estimate the fluid properties along the line length. The side branch impedance model was coupled to a chamber impedance model to show the effects on the overall chamber response. Predictions of the spin start acoustic behavior for helium operation are shown and compared against available data.

A method for starting up the gas isolating section of a benzine pyrolysis installation

Energy Technology Data Exchange (ETDEWEB)

Bruskin, Yu.A.; Gorokhov, V.V.; Kotler, L.D.; Shevchenko, K.N.; Zeldin, V.Ye.

1982-01-01

In the method for starting up a gas isolation section of a benzine pyrolysis unit, which includes starting the demethanizer in a steaming mode, starting the ethane and ethylene and propane and propylene towers, filling the ethylene cooling system with a hydrocarbon fraction, starting the ethylene cooling system, switching to a mode of the demethanization unit, starting the subassemblies for hydration and isolation of the ethylene and propylene fractions, in order to reduce the length of the start up period and to reduce the ejection of gas to the burner, after starting the demethanizer in the steaming mode, starting the ethane and ethylene and propane and propylene towers, the ethane and ethylene and propane and propylene fractions are mixed before the hydration subassemblies with an H2 bearing gas for catalytic reforming and then the other units and subassemblies are started.

Starting an Actuarial Science Major at a Liberal Arts College

Science.gov (United States)

Mills, Mark A.

2014-01-01

The article provides details of the process of starting an actuarial science major at a small, liberal arts college. Some critique of the major is included, as well as some challenges that may be faced by others wanting to start such a major at their institution.

Evaluation of Hawaii's Healthy Start Program.

Science.gov (United States)

Duggan, Anne K.; McFarlane, Elizabeth C.; Windham, Amy M.; Rohde, Charles A.; Salkever, David S.; Fuddy, Loretta; Rosenberg, Leon A.; Buchbinder, Sharon B.; Sia, Calvin C. J.

1999-01-01

Describes Hawaii's Healthy Start Program (HST), its ongoing evaluation study, and evaluation findings at the end of two of a planned three years of family-program participation and follow-up. HST uses home visitors to help prevent abusive and neglectful parenting. Found significant differences in program implementation among the three…

School Readiness in Children Living in Non-Parental Care: Impacts of Head Start

Science.gov (United States)

Lipscomb, Shannon T.; Pratt, Megan E.; Schmitt, Sara A.; Pears, Katherine C.; Kim, Hyoun K.

2013-01-01

The current study examines the effects of Head Start on the development of school readiness outcomes for children living in non-parental care. Data were obtained from the Head Start Impact Study, a randomized controlled trial of Head Start conducted with a nationally representative sample of Head Start programs and families. The sample included…

Healthy Start vitamins—a missed opportunity: findings of a multimethod study

Science.gov (United States)

McFadden, Alison; Green, Josephine M; McLeish, Jenny; McCormick, Felicia; Williams, Victoria; Renfrew, Mary J

2015-01-01

Objective To evaluate and provide a real-life view of the operation of the Healthy Start vitamins scheme. Setting The study took place in primary care and community settings that served rural, urban and ethnically diverse populations, in two sentinel sites: London, and Yorkshire and the Humber. An online consultation and stakeholder workshops elicited views from across England. Participants 669 health and social care practitioners including health visitors, midwives, public health practitioners, general practitioners, paediatricians and support staff participated in focus group discussions (n=49) and an online consultation (n=620). 56 participants representing health and social care practitioners, policymakers, service commissioners, and voluntary and independent sectors took part in stakeholder workshops. Methods Three-phase multimethod study comprising focus group discussions, an online consultation and stakeholder workshops. Qualitative data were analysed thematically and quantitative data from the online survey were analysed using descriptive statistics. Results Study participants were concerned about the low uptake of Healthy Start vitamin supplements and the consequences of this for health outcomes for women and young children. They experienced Healthy Start vitamin distribution as logistically complex, requiring the time, resources and creative thinking of a range of local and regional practitioners from senior strategists to administrative support workers. In the light of this, many participants argued that moving to universal provision of vitamin supplements would be more cost-effective than the current system. Conclusions There is consistency of views of health practitioners that the current targeted system of providing free vitamin supplements for low-income childbearing women and young children via the Healthy Start programme is not fulfilling its potential to address vitamin deficiencies. There is wide professional and voluntary sector support for

Experience in start-up of the South-Ukrainian-2 power unit with the WWER-1000 reactor

International Nuclear Information System (INIS)

Belov, Yu.V.; Kazakov, V.A.; Kirilov, V.V.; Kryakvin, L.V.

1987-01-01

The volume, sequence and dates of works fulfilled during hot testing, physical and power start-ups and while bringing output of the South-Ukranian-2 power unit with the WWER-1000 reactor to the design figure are described. The works were fulfilled according to the standard schedules from October in 1984 till April in 1985. Combination of the stages and intensification of works before the physical start-up have allowed to shorten the dates by 90 days as compared to the schedule. The physical and power start-ups, including bringing reactor output to the design figure, were performed during 140 days, that permits to shorten the dates by 20 days more. The results of physical experiments carried out at the South-Ukranian-2 power unit, are in good agreement with the data obtained at the first power units of the given and Kalinin NPPs. Besides, during physical and power start-ups additional measures ensuring nuclear safety are developed

The importance of cooperation and support for technology start-ups : a comparison of the Eindhoven and Darmstadt areas

NARCIS (Netherlands)

Halman, J.I.M.; Ulijn, J.M.; Vrande, van de V.J.A.; Umbach, F.; Ulijn, J.M.; Drillon, D.

2007-01-01

In Chapter 7, 'The importance of cooperation and support for technology start-ups: a comparison of the Eindhoven and Darmstadt areas', Johannes Halman, Jan Ulijn, Vareska van de Vrande and Frank Umbach show the results of a survey that was held among high-tech start-ups in the Eindhoven area ill the

An evaluation of designed Start-up System (SUS) for once-through steam generators

International Nuclear Information System (INIS)

Yu, Dali; Peng, Minjun; Xia, Genglei; Mao, Wanchao; Yang, Yang

2014-01-01

Highlights: • Four SUS solutions are established to help reactors complete the start-up process. • Solutions C and D lead to superior behaved than Solutions A and B. • Solution C is fit for propulsion reactors and Solution D for nuclear power reactors. - Abstract: In this paper, we report on research that has been carried out both on the comparison and evaluation of four designed Start-up Systems (SUSs), which are proposed to improve reliability and economy during the reactor start-up process. Firstly, four SUS solutions are established to satisfy demands and detailed descriptions are introduced. Then, four reactor systems, which include SUS, are modeled by the estimate code JTopmeret. Furthermore besides, the JTopmeret code is validated for the once-through steam generators (OTSG). Finally, the behaviors of SUS and the steady and transient performance of OTSG are investigated. The results show that the designed SUS can successfully improve the economy and the OTSG operational safety. Suggestion is made in this paper to apply Solution C in propulsion-purposed reactors, and Solution D in nuclear power reactors

Vortex Formation and Acceleration of a Fish-Inspired Robot Performing Starts from Rest

Science.gov (United States)

Devoria, Adam; Bapst, Jonathan; Ringuette, Matthew

2009-11-01

We investigate the unsteady flow of a fish-inspired robot executing starts from rest, with the objective of understanding the connection among the kinematics, vortex formation, and acceleration performance. Several fish perform ``fast starts,'' where the body bends into a ``C'' or ``S'' shape while turning (phase I), followed by a straightening of the body and caudal fin and a linear acceleration (phase II). The resulting highly 3-D, unsteady vortex formation and its relationship to the acceleration are not well understood. The self-propelled robotic model contains motor-driven joints with programmable motion to emulate phase II of a simplified C-start. The experiments are conducted in a water tank, and the model is constrained to 1 direction along rails. The velocity is measured using digital particle image velocimetry (DPIV) in multiple planes. Vortex boundaries are identified using the finite-time Lyapunov exponent, then the unsteady vortex circulation is computed. The thrust is estimated from the identified vortices, and correlated with the circulation and model acceleration for different kinematics.

The Early Start Denver Model: A Case Study of an Innovative Practice

Science.gov (United States)

Vismara, Laurie A.; Rogers, Sally J.

2008-01-01

Intervention was implemented with an infant identified at 9 months of age with a behavioral profile consistent with autistic spectrum disorder. The intervention approach, the Early Start Denver model, consisted of a 12-week, 1.5-hr-per-week individualized parent-child education program. Results of this case study demonstrated that the parent…

Child behavioural problems and body size among 2-6 year old children predisposed to overweight. results from the "healthy start" study.

Directory of Open Access Journals (Sweden)

Nanna J Olsen

Full Text Available OBJECTIVE: Psychological adversities among young children may be associated with childhood overweight and obesity. We examined if an increased level of child behavioural problems was associated with body size among a selected group of 2-6 year old children, who were all predisposed to develop overweight. METHODS: Cross-sectional analyses were conducted using baseline data from the "Healthy Start" intervention study. A total of 3058 children were invited to participate, and data from 583 children who were all predisposed for obesity was analyzed. The Danish version of the Strengths and Difficulties Questionnaire (SDQ was used to assess child stress by the SDQ Total Difficulties (SDQ-TD score and the Prosocial Behavior (PSB score. Height and weight were measured, and BMI z-scores were calculated. RESULTS: A direct, but non-significant linear trend was found between SDQ-TD score and BMI z-score (β = 0.021, p = 0.11. Having an SDQ-TD score above the 90(th percentile was associated with BMI z-score (β = 0.36, p = 0.05. PSB score was not associated with BMI z-score. Analyses were adjusted for parental socioeconomic status, parental BMI, family structure, dietary factors, physical activity, and family stress level. CONCLUSION: The results suggested a threshold effect between SDQ-TD score and BMI z-score, where BMI z-score was associated with childhood behavioural problems only for those with the highest scores of SDQ-TD. No significant association between PSB score and BMI z-score was found.

Design and Evaluation for Target Indicated Torque Based Engine Starting Control Strategy in a High Pressure Common Rail Diesel Engine

Directory of Open Access Journals (Sweden)

Xuedong Lin

2016-01-01

Full Text Available The diesel engine power demand of the start condition can be separated into two parts including resistance overcoming and acceleration realization for the reason that there is no power output during the starting process. The present paper mainly focuses on the fuel injection quantity control based on the engine power demand especially the acceleration demand for the resistance force is fixed for a specific engine, and the starting acceleration velocity is set as a target curve so that the acceleration process can also be fixed. The feasibility of the start control strategy proposed in this paper was verified by a comparison of the traditional starting control with a constant fuel quantity, and starting performance of the target acceleration based control shows predominance to the constant quantity control. And then the comparison between various starting acceleration processes, which was realized by the settings of acceleration curve slope factor, was conducted and results showed that the acceleration processes with higher slope factors perform better.

Starting Up after 50. CELCEE Digest.

Science.gov (United States)

Seymour, Nicole

Researchers are finding that older entrepreneurs are an increasing population in many Western countries. It is important to distinguish between entrepreneurs who have simply reached the age of 50 versus those who start up businesses after this age. The latter group is of particular interest because these people have presumably never faced the…

76 FR 70009 - Head Start Program

Science.gov (United States)

2011-11-09

... importance of the early years of a child's growth and development. On December 12, 2007, the Improving Head... education, serving nearly one million of our nation's most vulnerable young children and their families. It... Administration for Children and Families 45 CFR Part 1307 Head Start Program; Final Rule #0;#0;Federal Register...

Evaluation of Start Transient Oscillations with the J-2X Engine Gas Generator Assembly

Science.gov (United States)

Hulka, J. R.; Morgan, C. J.; Casiano, M. J.

2015-01-01

During development of the gas generator for the liquid oxygen/liquid hydrogen propellant J-2X rocket engine, distinctive and oftentimes high-amplitude pressure oscillations and hardware vibrations occurred during the start transient of nearly every workhorse gas generator assembly test, as well as during many tests of engine system hardware. These oscillations appeared whether the steady-state conditions exhibited stable behavior or not. They occurred similarly with three different injector types, and with every combustion chamber configuration tested, including chamber lengths ranging over a 5:1 range, several different nozzle types, and with or without a side branch line simulating a turbine spin start gas supply line. Generally, two sets of oscillations occurred, one earlier in the start transient and at higher frequencies, and the other almost immediately following and at lower frequencies. Multiple dynamic pressure measurements in the workhorse combustion chambers indicated that the oscillations were associated with longitudinal acoustic modes of the combustion chambers, with the earlier and higher frequency oscillation usually related to the second longitudinal acoustic mode and the later and lower frequency oscillation usually related to the first longitudinal acoustic mode. Given that several early development gas generator assemblies exhibited unstable behavior at frequencies near the first longitudinal acoustic modes of longer combustion chambers, the start transient oscillations are presumed to provide additional insight into the nature of the combustion instability mechanisms. Aspects of the steadystate oscillations and combustion instabilities from development and engine system test programs have been reported extensively in the three previous JANNAF Liquid Propulsion Subcommittee meetings (see references below). This paper describes the hardware configurations, start transient sequence operations, and transient and dynamic test data during the start

Start small and build toward business intelligence.

Science.gov (United States)

Kirby, Sean; Robertson, Brian

2009-01-01

To use business intelligence effectively, healthcare organizations should start small, align organizationally, and leverage success. Organizations should determine which measures they need and how to present them. Organizations should reinvest savings to continually improve.

Revised emission factors for gas engines including start/stop emissions

Energy Technology Data Exchange (ETDEWEB)

Nielsen, Malene; Boll Illerup, J.; Birr-Petersen, K.

2008-06-15

Liberalisation of the electricity market has led to Danish gas engine plants increasingly converting to the spot and regulating power markets. In order to offer regulating power, plants need to be able to start and stop the engines at the plants quickly. The liberalisation causes a considerable change of operation practice of the engines e.g. less full load operation hours /year. The project provides an inventory determining the scale of the emissions during the start and stop sequence as well as proposals for engine modifications aimed at reducing start/stop emissions. This report includes calculation of emission factors as well as an inventory of total emissions and reduction potentials. (au)

Exploration of cloud computing late start LDRD #149630 : Raincoat. v. 2.1.

Energy Technology Data Exchange (ETDEWEB)

Echeverria, Victor T.; Metral, Michael David; Leger, Michelle A.; Gabert, Kasimir Georg; Edgett, Patrick Garrett; Thai, Tan Q.

2010-09-01

This report contains documentation from an interoperability study conducted under the Late Start LDRD 149630, Exploration of Cloud Computing. A small late-start LDRD from last year resulted in a study (Raincoat) on using Virtual Private Networks (VPNs) to enhance security in a hybrid cloud environment. Raincoat initially explored the use of OpenVPN on IPv4 and demonstrates that it is possible to secure the communication channel between two small 'test' clouds (a few nodes each) at New Mexico Tech and Sandia. We extended the Raincoat study to add IPSec support via Vyatta routers, to interface with a public cloud (Amazon Elastic Compute Cloud (EC2)), and to be significantly more scalable than the previous iteration. The study contributed to our understanding of interoperability in a hybrid cloud.

Promoting academic and social-emotional school readiness: the head start REDI program.

Science.gov (United States)

Bierman, Karen L; Domitrovich, Celene E; Nix, Robert L; Gest, Scott D; Welsh, Janet A; Greenberg, Mark T; Blair, Clancy; Nelson, Keith E; Gill, Sukhdeep

2008-01-01

Forty-four Head Start classrooms were randomly assigned to enriched intervention (Head Start REDI-Research-based, Developmentally Informed) or "usual practice" conditions. The intervention involved brief lessons, "hands-on" extension activities, and specific teaching strategies linked empirically with the promotion of: (a) social-emotional competencies and (b) language development and emergent literacy skills. Take-home materials were provided to parents to enhance skill development at home. Multimethod assessments of three hundred and fifty-six 4-year-old children tracked their progress over the course of the 1-year program. Results revealed significant differences favoring children in the enriched intervention classrooms on measures of vocabulary, emergent literacy, emotional understanding, social problem solving, social behavior, and learning engagement. Implications are discussed for developmental models of school readiness and for early educational programs and policies.

Affective Meaning, Concreteness, and Subjective Frequency Norms for Indonesian Words

Directory of Open Access Journals (Sweden)

Agnes Sianipar

2016-12-01

Full Text Available This study investigated the lexical-semantic space organized by the semantic and affective features of Indonesian words and their relationship with gender and cultural aspects. We recruited 1,402 participants who were native speakers of Indonesian to rate affective and lexico-semantic properties of 1,490 Indonesian words. Valence, Arousal, Dominance, Predictability, Subjective Frequency, and Concreteness ratings were collected for each word from at least 52 people. We explored cultural differences between American English ANEW, Spanish ANEW, and the new Indonesian inventory (called CEFI. We found functional relationships between the affective dimensions that were similar across languages, but also cultural differences dependent on gender.

Power start up of the Dalat nuclear research reactor

International Nuclear Information System (INIS)

Pham Duy Hien; Ngo Quang Huy; Vu Hai Long; Tran Khanh Mai

1994-01-01

After accomplishing the physical start-up of the reactor, the power start-up was carried out in February 1984. The power of the reactor has reached: 10 KW on 6/2/1984, 100 KW on 7/2/1984, 200 KW and 300 KW on 8/2/1984; 400 KW and nominal power 500 KW on 9/2/1984. The reactivity temperature coefficient and the xenon poisoning were determined. 3 figs., 12 tabs

Head Start's Impact Is Contingent on Alternative Type of Care in Comparison Group

Science.gov (United States)

Zhai, Fuhua; Brooks-Gunn, Jeanne; Waldfogel, Jane

2014-01-01

Using data ("n" = 3,790 with 2,119 in the 3-year-old cohort and 1,671 in the 4-year-old cohort) from 353 Head Start centers in the Head Start Impact Study, the only large-scale randomized experiment in Head Start history, this article examined the impact of Head Start on children's cognitive and parent-reported social-behavioral outcomes…

76 FR 50887 - Elections Regarding Start-Up Expenditures, Corporation Organizational Expenditures, and...

Science.gov (United States)

2011-08-17

... begins an active trade or business, an amount equal to the lesser of (1) the amount of the start-up... begins. All start-up expenditures that relate to the active trade or business are considered in... active trade or business to which the expenditures relate begins. The election either to amortize start...

DBSSP - A computer program for simulation of controlled circulation boiler and natural circulation boiler start up behavior

International Nuclear Information System (INIS)

Li Bin; Chen Tingkuan; Yang Dong

2005-01-01

In this paper, a computer program, Drum Boiler Start-up Simulation Program (DBSSP), is developed for simulating the start up behavior of controlled circulation and natural circulation boilers. The mathematical model developed here is based on the first principles of mass, energy and momentum conservations. In the boiler model, heat transfer in the waterwall, the superheater, the reheater and the economizer is simulated by the distributing parameter method, while heat transfer in the drum and the downcomer is simulated by lumped parameter analysis. The program can provide detailed flow and thermodynamic characteristics of the boiler components. The development of this program is based only on design data, so it can be used for any subcritical, controlled or natural circulation boiler. The simulation results were compared with experimental measurements, and good agreements between them were found. This program is expected to be useful for predicting the characteristics and the performance of controlled circulation and natural circulation boilers during the start up process. It also can be used to optimize a start up system for minimum start up time

Detection of combustion start in the controlled auto ignition engine by wavelet transform of the engine block vibration signal

International Nuclear Information System (INIS)

Kim, Seonguk; Min, Kyoungdoug

2008-01-01

The CAI (controlled auto ignition) engine ignites fuel and air mixture by trapping high temperature burnt gas using a negative valve overlap. Due to auto ignition in CAI combustion, efficiency improvements and low level NO x emission can be obtained. Meanwhile, the CAI combustion regime is restricted and control parameters are limited. The start of combustion data in the compressed ignition engine are most critical for controlling the overall combustion. In this research, the engine block vibration signal is transformed by the Meyer wavelet to analyze CAI combustion more easily and accurately. Signal acquisition of the engine block vibration is a more suitable method for practical use than measurement of in-cylinder pressure. A new method for detecting combustion start in CAI engines through wavelet transformation of the engine block vibration signal was developed and results indicate that it is accurate enough to analyze the start of combustion. Experimental results show that wavelet transformation of engine block vibration can track the start of combustion in each cycle. From this newly developed method, the start of combustion data in CAI engines can be detected more easily and used as input data for controlling CAI combustion

Detection of combustion start in the controlled auto ignition engine by wavelet transform of the engine block vibration signal

Science.gov (United States)

Kim, Seonguk; Min, Kyoungdoug

2008-08-01

The CAI (controlled auto ignition) engine ignites fuel and air mixture by trapping high temperature burnt gas using a negative valve overlap. Due to auto ignition in CAI combustion, efficiency improvements and low level NOx emission can be obtained. Meanwhile, the CAI combustion regime is restricted and control parameters are limited. The start of combustion data in the compressed ignition engine are most critical for controlling the overall combustion. In this research, the engine block vibration signal is transformed by the Meyer wavelet to analyze CAI combustion more easily and accurately. Signal acquisition of the engine block vibration is a more suitable method for practical use than measurement of in-cylinder pressure. A new method for detecting combustion start in CAI engines through wavelet transformation of the engine block vibration signal was developed and results indicate that it is accurate enough to analyze the start of combustion. Experimental results show that wavelet transformation of engine block vibration can track the start of combustion in each cycle. From this newly developed method, the start of combustion data in CAI engines can be detected more easily and used as input data for controlling CAI combustion.

Urgent-Start Peritoneal Dialysis Complications: Prevalence and Risk Factors.

Science.gov (United States)

Xu, Damin; Liu, Tianjiao; Dong, Jie

2017-07-01

Mechanical complications are of particular concern in urgent-start peritoneal dialysis (PD) because of the shorter break-in period. However, risk factors have been reported inconsistently and data in urgent-start PD populations are limited. Observational cohort study. All patients treated with urgent-start PD, defined as PD therapy initiated within 1 week after catheter insertion, January 2003 to May 2013. Age, sex, abdominal surgery history, body mass index, hemoglobin level, albumin level, C-reactive protein level, break-in period (period between catheter insertion and PD therapy initiation), dialysate exchange volume, and use of overnight dwell. The presence of mechanical complications related to abdominal wall or catheter, including hernia, hydrothorax, hydrocele, subcutaneous leak, pericatheter leak, catheter malposition, omental wrap, and obstruction. 922 patients on urgent-start PD therapy were enrolled (mean age, 59.1±15.0 [SD] years). Prevalences of abdominal wall and catheter complications were 4.8% and 9.5%, respectively. The most common abdominal wall complication was hernia (55%), followed by hydrothorax (25%). On adjustment, male sex (HR, 5.41; 95% CI, 2.15-13.59; Pstart PD and conventional PD. Urgent-start PD is a safe and practicable approach. Male sex and history of abdominal surgery could contribute to the development of abdominal wall complications. Copyright © 2017 National Kidney Foundation, Inc. Published by Elsevier Inc. All rights reserved.

Does peritoneal dialysis have a role in urgent-start end-stage kidney disease?

Science.gov (United States)

McQuillan, Rory F; Lok, Charmaine E

2018-04-19

Despite its many positive attributes, peritoneal dialysis remains underutilized, particularly in the United States. Urgent-start peritoneal dialysis (PD) has been proposed as a method of increasing PD prevalence. Urgent-start PD has been shown to be safe, feasible, and effective. However, urgent-start PD is also accompanied by several multidimensional challenges. This article is intended to equip the reader with a practical sense of whether an urgent-start PD program would be appropriate in his or her own clinical context and if appropriate, what factors would be necessary for such a program to flourish. As such, we summarize latent factors, which are necessary to consider before instituting an urgent-start PD. Then, using a series of clinical vignettes, highlight the component parts of a successful urgent-start PD program and the patient population who stand to benefit most from this strategy. The discussion is then balanced by presenting limitations to consider in the urgent-start PD approach. © 2018 Wiley Periodicals, Inc.

Split-phase motor running as capacitor starts motor and as capacitor run motor

Directory of Open Access Journals (Sweden)

Yahaya Asizehi ENESI

2016-07-01

Full Text Available In this paper, the input parameters of a single phase split-phase induction motor is taken to investigate and to study the output performance characteristics of capacitor start and capacitor run induction motor. The value of these input parameters are used in the design characteristics of capacitor run and capacitor start motor with each motor connected to rated or standard capacitor in series with auxiliary winding or starting winding respectively for the normal operational condition. The magnitude of capacitor that will develop maximum torque in capacitor start motor and capacitor run motor are investigated and determined by simulation. Each of these capacitors is connected to the auxiliary winding of split-phase motor thereby transforming it into capacitor start or capacitor run motor. The starting current and starting torque of the split-phase motor (SPM, capacitor run motor (CRM and capacitor star motor (CSM are compared for their suitability in their operational performance and applications.

Bypass line assisted start-up of a loop heat pipe with a flat evaporator

International Nuclear Information System (INIS)

Boo, Joon Hong; Jung, Eui Guk

2009-01-01

Loop heat pipes often experience start-up problems especially under low thermal loads. A bypass line was installed between the evaporator and the liquid reservoir to alleviate the difficulties associated with start-up of a loop heat pipe with flat evaporator. The evaporator and condenser had dimensions of 40 mm (W) by 50 mm (L). The wall and tube materials were stainless steel and the working fluid was methanol. Axial grooves were provided in the flat evaporator to serve as vapor passages. The inner diameters of liquid and vapor transport lines were 2 mm and 4 mm, respectively, and the length of the two lines was 0.5 m each. The thermal load range was up to 130 W for horizontal alignment with the condenser temperature of 10 .deg. C. The experimental results showed that the minimum thermal load for start-up was lowered by 37% when the bypass line was employed

Effect of the Modification of the Start-Up Sequence on the Thermal Stresses for a Microgas Turbine

Directory of Open Access Journals (Sweden)

Oscar Tenango-Pirin

2016-01-01

Full Text Available Microgas turbines (MGT are an alternative for small-scale energy production; however, their small size becomes a drawback since it enhances the heat transfer among their components. Moreover, heat transfer drives to temperature gradients which become higher during transient cycles like start-up. The influence of different start-up curves on temperature and thermal stresses of a microgas turbine was investigated. Stationary and rotational blades of the turbine were numerically simulated using CFD and FEM commercial codes. Conjugated heat transfer cases were solved for obtaining heat transfer from fluid toward the blades. Changes of temperature gradients within the blades during the start-ups were calculated under transient state with boundary conditions according to each curve to assess accurate thermal stresses calculations. Results showed that the modification of the start-up curves had an impact on the thermal stresses levels and on the time when highest stresses appeared on each component. Furthermore, zones highly stressed were located near the constraints of blades where thermal strains are restricted. It was also found that the curve that had a warming period at the beginning of the start-up allowed reducing the peaks of stresses making it more feasible and safer for the turbine start-up operation.

Danish Ophthalmology - from start to 1865.

Science.gov (United States)

Norn, Mogens

2016-03-01

This short paper mentioned the medical treatment using the 'holy' springs, the first 'eye doctor' in Denmark, the first picture of spectacles which was found in Viborg Cathedral of the high priest before he performs circumcisio praeputii on Jesus Christ, further cataract reclination in Denmark from around year zero and cataract extraction in 1667 in Denmark on a goose by Francisco Borri and on humans by the Danish Georg Heuermann in 1755. Epidemic military eye diseases in 1807, 1856 and 1865 are also described in this study. From 1856, a new ophthalmological period started in Denmark with the first eye hospital (lazaret only for eye diseases), and in 1864, patients with eye diseases were transported from the few beds in the surgical departments in the municipal hospital to the first civil eye department in Denmark, the eye hospital Sct. Annae in Copenhagen. The new scientific period started with Jacob Christian Bentz (ophthalmia granulosa, joint editor of the Danish Medical Journal) and Heinrich Lehmann. © 2016 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Ukraine stalls on START I vote; presses US on aid, security issues

International Nuclear Information System (INIS)

Lockwood, D.

1993-01-01

In early January, a Ukrainian delegation came to Washington to discuss issues related to Ukrainian ratification of START I and accession to the nuclear Non-Proliferation Treaty (NPT). The issues discussed at the meeting (US security assurances and economic aid), which were not resolved, have serious implications for START I, the NPT, and the flow-on START II agreement

Optimal relations of the parameters ensuring safety during reactor start-up

International Nuclear Information System (INIS)

Yurkevich, G.P.

2004-01-01

Procedure and equations for the determination of optimal ratio between parameters allowing safe removal of reactor in critical state are suggested. Initial pulse frequency of pulsed start-up channel and power of neutron source are decreased by reduced rate of changing reactivity during automatic start-up, disposition of pulsed neutron detector in the range with neutron flux density to 5·10 12 s -1 cm -2 at standard power, separate signal of period for the use in chains of automatic start-up and emergency protection, reduction of pulses frequency of the start-up channel (the frequency is equal to 4000 c -1 ). Procedure and equations for the determination of optimal parameters are effected with the account of statistic character of pulsed detector frequency and false outlet signal [ru

Self-starting aerodynamics analysis of vertical axis wind turbine

OpenAIRE

Jianyang Zhu; Hailin Huang; Hao Shen

2015-01-01

Vertical axis wind turbine is a special type of wind-force electric generator which is capable of working in the complicated wind environment. The self-starting aerodynamics is one of the most important considerations for this kind of turbine. This article aims at providing a systematic synthesis on the self-starting aerodynamic characteristics of vertical axis wind turbine based on the numerical analysis approach. First, the physical model of vertical axis wind turbine and its parameter defi...

Strategic Management: Business Model Canvas for Start-Up Company

OpenAIRE

Sonninen, Anna

2016-01-01

Thesis is written about development of Kakunpala as a Start-Up Company, because development processes and ideas are the key factors for future success of the company. The aim of this thesis is to understand Strategic Management of the Company and Development processes,by using the SWOT analysis before and after development and by applying Business Model Canvas template to the Start-Up Company, and by describing Customer Journey: what relations Kakunpala has with clients and its processes...

Eleven Tribes Jump START Clean Energy Projects, Summer 2012 (Newsletter)

Energy Technology Data Exchange (ETDEWEB)

2012-06-01

This newsletter describes key activities of the DOE Office of Indian Energy Policy and Programs for Summer 2012. The U.S. Department of Energy Office of Indian Energy Policy and Programs (DOE-IE) has selected 11 Tribes - five in Alaska and six in the contiguous United States - to receive on-the-ground technical support for community-based energy efficiency and renewable energy projects as part of DOE-IE's Strategic Technical Assistance Response Team (START) Program. START finalists were selected based on the clarity of their requests for technical assistance and the ability of START to successfully work with their projects or community. Technical experts from DOE and its National Renewable Energy Laboratory (NREL) will work directly with community-based project teams to analyze local energy issues and assist the Tribes in moving their projects forward. In Alaska, the effort will be bolstered by DOE-IE's partnership with the Denali Commission, which will provide additional assistance and expertise, as well as funding to fuel the Alaska START initiative.

The Start of a Tech Revolution

Science.gov (United States)

Dyrli, Kurt O.

2009-01-01

We are at the start of a revolution in the use of computers, one that analysts predict will rival the development of the PC in its significance. Companies such as Google, HP, Amazon, Sun Microsystems, Sony, IBM, and Apple are orienting their entire business models toward this change, and software maker SAS has announced plans for a $70 million…

Exercise starts and ends in the brain.

Science.gov (United States)

Kayser, Bengt

2003-10-01

Classically the limit to endurance of exercise is explained in terms of metabolic capacity. Cardio-respiratory capacity and muscle fatigue are thought to set the limit and the majority of studies on factors limiting endurance exercise discuss issues such as maximal oxygen uptake (VO2max), aerobic enzyme capacity, cardiac output, glycogen stores, etc. However, this paradigm does not explain the limitation to endurance exercise with large muscle groups at altitude, when at exhaustion exercise is ended without limb locomotor muscle fatigue and with sub-maximal cardiac output. A simple fact provides a basis for an explanation. Voluntary exercise starts and ends in the brain. It starts with spatial and temporal recruitment of motor units and ends with their de-recruitment. A conscious decision precedes a voluntary effort. The end of effort is again volitional and a forced conscious decision to stop precedes it, but it is unknown what forces the off-switch of recruitment at exhaustion although sensation of exertion certainly plays a role. An alternative model explaining the limitation of exercise endurance thus proposes that the central nervous system integrates input from various sources all related to the exercise and limits the intensity and duration of recruitment of limb skeletal muscle to prevent jeopardizing the integrity of the organism. This model acknowledges the cardio-respiratory and muscle metabolic capacities as prime actors on the performance scene, while crediting the central nervous system for its pivotal role as the ultimate site where exercise starts and ends.

How Types of Organisational Culture Shapes Successful Start-ups within Malaysia

OpenAIRE

Kuah, Shen Yang

2016-01-01

Start-ups is the new wave of firms which are now mushrooming around Malaysia. However, as this wave is still at its infancy the success rate of start-ups in Malaysia is extremely low. It has been long established that organisational culture does indeed effect the performance of a firm, however there haven’t been any reports on the effect of organisational culture on the success of start-ups. The objective of this report is to investigate how different types of organisational cultures contribu...

Pseudo one-dimensional analysis of polymer electrolyte fuel cell cold-start

Energy Technology Data Exchange (ETDEWEB)

Mukherjee, Partha P [Los Alamos National Laboratory; Mukundan, Rangachary [Los Alamos National Laboratory; Borup, Rodney L [Los Alamos National Laboratory; Wang, Yun [NON LANL; Mishlera, Jeff [NON LANL

2009-01-01

This paper investigates the electrochemical kinetics, oxygen transport, and solid water formation in polymer electrolyte fuel cell (PEFC) during cold start. Following [Yo Wang, J. Electrochem. Soc., 154 (2007) B1041-B1048], we develop a pseudo one-dimensional analysis, which enables the evaluation of the impact of ice volume fraction and temperature variations on cell performance during cold-start. The oxygen profile, starvation ice volume fraction, and relevant overpotentials are obtained. This study is valuable for studying the characteristics of PEFC cold-start.

Spring 
start-up for the LHC

CERN Multimedia

2007-01-01

A new schedule for the commissioning of the LHC was presented to the Council at its Session in June. The start-up of the accelerator is scheduled for May 2008, to allow all technical problems to be resolved.

THE EFFECTS OF THREE DIFFERENT REAR KNEE ANGLES ON KINEMATICS IN THE SPRINT START

Directory of Open Access Journals (Sweden)

C. Milanese

2014-08-01

Full Text Available The purpose of this study was to investigate the rear knee angle range in the set position that allows sprinters to reach greater propulsion on the rear block during the sprint start. Eleven university-track team sprinters performed the sprint start using three rear knee angle conditions: 90°, 115° and 135°. A motion capture system consisting of 8 digital cameras (250 Hz was used to record kinematic parameters at the starting block phase and the acceleration phase. The following variables were considered: horizontal velocity of the centre of mass (COM, COM height, block time, pushing time on the rear block, percentage of pushing time on the rear block, force impulse, push-off angle and length of the first two strides. The main results show that first, horizontal block velocity is significantly greater at 90° vs 115° and 135° rear knee angle (p<0.05 and p<0.001 respectively at block clearance and the first two strides; second, during the pushing phase, the percentage of pushing time of the rear leg is significantly greater at 90° vs 135° rear knee angle (p<0.01. No significant difference was found for block time among the conditions. These results indicate that block velocity is the main kinematic parameter affected by rear knee angle during the starting block phase and acceleration phase. Furthermore, the 90° rear knee angle allows for a better push-off of the rear leg than larger angles at the set position. The findings of this study provide some direction and useful practical advice in defining an efficient rear leg biomechanical configuration at the set position.

Getting started With Amazon Redshift

CERN Document Server

Bauer, Stefan

2013-01-01

Getting Started With Amazon Redshift is a step-by-step, practical guide to the world of Redshift. Learn to load, manage, and query data on Redshift.This book is for CIOs, enterprise architects, developers, and anyone else who needs to get familiar with RedShift. The CIO will gain an understanding of what their technical staff is working on; the technical implementation personnel will get an in-depth view of the technology, and what it will take to implement their own solutions.

Getting started with Drupal commerce

CERN Document Server

Jones, Richard

2013-01-01

A simple yet concise step-by-step tutorial that starts from scratch and builds up your knowledge with focused examples that will enable you to set up and run an e-commerce website.This book is for beginners and will take you through the installation and configuration of Drupal Commerce from scratch, but some familiarity with Drupal 7 will be an advantage. All examples are based on development on a local computer - you do not need a hosted Drupal environment.

Early Head Start Participants, Programs, Families, and Staff in 2014

Science.gov (United States)

Mohan, Anitha; Walker, Christina

2016-01-01

In 1994, the federal Early Head Start (EHS) program was created to address the comprehensive needs of low-income pregnant women and children under age 3. EHS was launched almost 30 years after Head Start was established in 1965 to serve low-income 3- and 4-year-old children and their families with comprehensive early education and support…

Head Start Teacher Well-Being: Implications for Policy and Practice

Science.gov (United States)

Bullough, Robert V., Jr.; Hall-Kenyon, Kendra M.; MacKay, Kathryn Lake

2012-01-01

Surprisingly little is known about Head Start teachers; who teaches, why they teach, and how they think and feel about their work. To begin to address these issues, a survey was developed and distributed to Head Start teachers, assistant teachers, and aides in one three-county program to examine their motivation and well-being. Follow-up…

Fast-starting for a breath: Air breathing in Hoplosternum littorale

DEFF Research Database (Denmark)

Domenici, Paolo; Norin, Tommy; Bushnell, Peter G.

by the fall of a prey item on the water surface, and in tapping motions of goldfish, a behaviour that was interpreted to be food-related. Little is known about C-starts being used outside the context of escaping or feeding. Here, we test the hypothesis that air-breathing fish may use C-starts when gulping air...

Does Head Start differentially benefit children with risks targeted by the program's service model?

Science.gov (United States)

Miller, Elizabeth B; Farkas, George; Duncan, Greg J

Data from the Head Start Impact Study ( N = 3540) were used to test for differential benefits of Head Start after one program year and after kindergarten on pre-academic and behavior outcomes for children at risk in the domains targeted by the program's comprehensive services. Although random assignment to Head Start produced positive treatment main effects on children's pre-academic skills and behavior problems, residualized growth models showed that random assignment to Head Start did not differentially benefit the pre-academic skills of children with risk factors targeted by the Head Start service model. The models showed detrimental impacts of Head Start for maternal-reported behavior problems of high-risk children, but slightly more positive impacts for teacher-reported behavior. Policy implications for Head Start are discussed.

Minto, Alaska Lakeview Lodge START Program Weatherization and Rehab Project Final Report

Energy Technology Data Exchange (ETDEWEB)

Titus, Bessie [Minto Tribal Council, Minto, AK (United States); Messier, Dave [Minto Tribal Council, Minto, AK (United States)

2015-11-20

This report details the process that Minto Village Council undertook during the DOE sponsored START program and the work that was completed on the main energy consumer in the community, the Minto Lakeview Lodge. The report takes a look at the steps leading up to the large weatherization and renovation project, the work the was completed as a result of the funding and the results in terms of effect on the community and real energy savings.

Application of the STOPP/START criteria to a medical record database.

Science.gov (United States)

Nauta, Katinka J; Groenhof, Feikje; Schuling, Jan; Hugtenburg, Jacqueline G; van Hout, Hein P J; Haaijer-Ruskamp, Flora M; Denig, Petra

2017-10-01

The STOPP/START criteria are increasingly used to assess prescribing quality in elderly patients at practice level. Our aim was to test computerized algorithms for applying these criteria to a medical record database. STOPP/START criteria-based computerized algorithms were defined using Anatomical-Therapeutic-Chemical (ATC) codes for medication and International Classification of Primary Care (ICPC) codes for diagnoses. The algorithms were applied to a Dutch primary care database, including patients aged ≥65 years using ≥5 chronic drugs. We tested for associations with patient characteristics that have previously shown a relationship with the original STOPP/START criteria, using multivariate logistic regression models. Included were 1187 patients with a median age of 75 years. In total, 39 of the 62 STOPP and 18 of the 26 START criteria could be converted to a computerized algorithm. The main reasons for inapplicability were lack of information on the severity of a condition and insufficient covering of ICPC-codes. We confirmed a positive association between the occurrence of both the STOPP and the START criteria and the number of chronic drugs (adjusted OR ranging from 1.37, 95% CI 1.04-1.82 to 3.19, 95% CI 2.33-4.36) as well as the patient's age (adjusted OR for STOPP 1.30, 95% CI 1.01-1.67; for START 1.73, 95% CI 1.35-2.21), and also between female gender and the occurrence of STOPP criteria (adjusted OR 1.41, 95% CI 1.09-1.82). Sixty-five percent of the STOPP/START criteria could be applied with computerized algorithms to a medical record database with ATC-coded medication and ICPC-coded diagnoses. Copyright © 2017 John Wiley & Sons, Ltd.

Reasons for Starting and Stopping Electronic Cigarette Use

Directory of Open Access Journals (Sweden)

Jessica K. Pepper

2014-10-01

Full Text Available The aim of our study was to explore reasons for starting and then stopping electronic cigarette (e-cigarette use. Among a national sample of 3878 U.S. adults who reported ever trying e-cigarettes, the most common reasons for trying were curiosity (53%; because a friend or family member used, gave, or offered e-cigarettes (34%; and quitting or reducing smoking (30%. Nearly two-thirds (65% of people who started using e-cigarettes later stopped using them. Discontinuation was more common among those whose main reason for trying was not goal-oriented (e.g., curiosity than goal-oriented (e.g., quitting smoking (81% vs. 45%, p < 0.001. The most common reasons for stopping e-cigarette use were that respondents were just experimenting (49%, using e-cigarettes did not feel like smoking cigarettes (15%, and users did not like the taste (14%. Our results suggest there are two categories of e-cigarette users: those who try for goal-oriented reasons and typically continue using and those who try for non-goal-oriented reasons and then typically stop using. Research should distinguish e-cigarette experimenters from motivated users whose decisions to discontinue relate to the utility or experience of use. Depending on whether e-cigarettes prove to be effective smoking cessation tools or whether they deter cessation, public health programs may need distinct strategies to reach and influence different types of users.

Time program using in automatization of steam turbines start-up

International Nuclear Information System (INIS)

Lejzerovich, A.Sh.; Melamed, A.D.

Examples and arguments for developing time programs of changing basic parameters of automated start-up of TPP and NPP high-power steam turbines are considered. Basic parameters subject to controlled changing at automatization of turbine start-up are rotation frequency, loading and temperature of steam supplied to the turbine. Principle facility schemes of program regulation of steam temperature at the start-up are presented. The facility scheme of loading the NPP wet steam turbine is given. The principles of developing time programs, of changing basic parameters of automated start-up enable realizing transient processes close to theoretically optimum processes at arbitrary prestart-up state of the turbine by means of rather simple autatic facilities. In particular, for automated temperature increase of steam supplied to the turbine of TES power units and AES turbine loading, it is advisable to use programs in the form of linear dependence of velocity of changing the controlled parameter on the given value, the initial level, from which the parameter increase with a regulated velocity is realized, is given in the form of analogue dependence on the turbine prestart-up state. The programs described and the schemes of their realization have been approved at the automatization of 300 MW power unit starts up with the K-300-240 turbine and K-220-44 turbine as well as used when creating control system for turbines of 500 MW and higher for designed TPP and NPP power units

The New START Treaty: Central Limits and Key Provisions

Science.gov (United States)

2014-08-27

article-by-article analysis can be found at http://www.state.gov/t/ avc /newstart/c44126.htm. 2 For a brief summary of the original START Treaty, as...2014, http://www.state.gov/t/ avc /rls/224236.htm . The fact sheet does not display warhead subtotals for each delivery system; it only includes an...of Strategic Offensive Forces, Fact Sheet, Washington, DC, April 1, 2014, http://www.state.gov/t/ avc /rls/228652.htm. The New START Treaty: Central

A Review on Cold Start of Proton Exchange Membrane Fuel Cells

Directory of Open Access Journals (Sweden)

Zhongmin Wan

2014-05-01

Full Text Available Successful and rapid startup of proton exchange membrane fuel cells (PEMFCs at subfreezing temperatures (also called cold start is of great importance for their commercialization in automotive and portable devices. In order to maintain good proton conductivity, the water content in the membrane must be kept at a certain level to ensure that the membrane remains fully hydrated. However, the water in the pores of the catalyst layer (CL, gas diffusion layer (GDL and the membrane may freeze once the cell temperature decreases below the freezing point (Tf. Thus, methods which could enable the fuel cell startup without or with slight performance degradation at subfreezing temperature need to be studied. This paper presents an extensive review on cold start of PEMFCs, including the state and phase changes of water in PEMFCs, impacts of water freezing on PEMFCs, numerical and experimental studies on PEMFCs, and cold start strategies. The impacts on each component of the fuel cell are discussed in detail. Related numerical and experimental work is also discussed. It should be mentioned that the cold start strategies, especially the enumerated patents, are of great reference value on the practical cold start process.

STOPP/START criteria for potentially inappropriate prescribing in older people: version 2.

Science.gov (United States)

O'Mahony, Denis; O'Sullivan, David; Byrne, Stephen; O'Connor, Marie Noelle; Ryan, Cristin; Gallagher, Paul

2015-03-01

Screening tool of older people's prescriptions (STOPP) and screening tool to alert to right treatment (START) criteria were first published in 2008. Due to an expanding therapeutics evidence base, updating of the criteria was required. We reviewed the 2008 STOPP/START criteria to add new evidence-based criteria and remove any obsolete criteria. A thorough literature review was performed to reassess the evidence base of the 2008 criteria and the proposed new criteria. Nineteen experts from 13 European countries reviewed a new draft of STOPP & START criteria including proposed new criteria. These experts were also asked to propose additional criteria they considered important to include in the revised STOPP & START criteria and to highlight any criteria from the 2008 list they considered less important or lacking an evidence base. The revised list of criteria was then validated using the Delphi consensus methodology. The expert panel agreed a final list of 114 criteria after two Delphi validation rounds, i.e. 80 STOPP criteria and 34 START criteria. This represents an overall 31% increase in STOPP/START criteria compared with version 1. Several new STOPP categories were created in version 2, namely antiplatelet/anticoagulant drugs, drugs affecting, or affected by, renal function and drugs that increase anticholinergic burden; new START categories include urogenital system drugs, analgesics and vaccines. STOPP/START version 2 criteria have been expanded and updated for the purpose of minimizing inappropriate prescribing in older people. These criteria are based on an up-to-date literature review and consensus validation among a European panel of experts. © The Author 2014. Published by Oxford University Press on behalf of the British Geriatrics Society.

Start-up of anaerobic digestion of source-sorted organic municipal solid waste

International Nuclear Information System (INIS)

Maroun, Rania

2004-01-01

Municipal solid waste (MSW) disposal is a major environmental concern worldwide. Among the environmentally sound technologies for the treatment of MSW, composting in the form of anaerobic digestion (AD) appears as a suitable alternative that offers the advantage of rapid stabilization of organic matter, reduction in waste volume, production of methane, and minimal environmental impacts in comparison to land filling and incineration. Yet, although outstanding advances in anaerobic digestion of solid substrate have been made in the last 10 years, some development areas are lagging, including the fast and reliable process start-up in terms of type of inocula and overall start-up strategies. The present study investigates the start-up and operation of bench-scale anaerobic digesters treating the source-sorted organic fraction of municipal solid waste. The experimental program consisted of starting up two digesters in parallel. Three consecutive interventions in the start-up program were implemented to achieve steady state. Start-up was relatively slow indicating the seed obtained from an operating anaerobic wastewater treatment plant was not suitable. The use of cattle manure together with effluent dilution reduced the acclimation period (Author.)

Social Capital in Knowledge Intensive Start-Ups

DEFF Research Database (Denmark)

Neergaard, Helle; Madsen, Henning

This paper addresses social capital in biotechnology, medico and information communication start-ups using both quantitative and qualitative data. It shows that founding teams are primarily composed of 'trusted alters' and that networking patterns are highly influenced by the entrepreneur...

University–industry collaboration: Jump-starting innovation | IDRC ...

International Development Research Centre (IDRC) Digital Library (Canada)

2010-10-06

Oct 6, 2010 ... In Costa Rica, researchers and business have found innovative ways to ... To jump-start these collaborations, IDRC is supporting research teams in 12 ... steel company recently tried to license a type of steel easy to mould into ...

Analysis of automobile’s automatic control systems for the hill climbing start

Directory of Open Access Journals (Sweden)

Valeriy I. Klimenko

2014-12-01

Full Text Available To improve road safety while driving on the rise, facilitating the driver’s activity the automobile industry leaders are introducing automatic hill-hold control systems into the car design. This study purpose relates to the existing automatic start control systems’ design analysis. Analyzed are the existing design developments of automatic hill start assist control systems applied for driving at the start of the climbing. The effected research allows to select the scheme for further development of start driving automatic control systems. Further improvement of driving control systems and primarily the driver assistance hill-hold control systems is necessary to increase both the driving comfort and the traffic safety.

Manual wheelchair propulsion patterns on natural surfaces during start-up propulsion.

Science.gov (United States)

Koontz, Alicia M; Roche, Bailey M; Collinger, Jennifer L; Cooper, Rory A; Boninger, Michael L

2009-11-01

To classify propulsion patterns over surfaces encountered in the natural environment during start-up and compare selected biomechanical variables between pattern types. Case series. National Veterans Wheelchair Games, Minneapolis, MN, 2005. Manual wheelchair users (N=29). Subjects pushed their wheelchairs from a resting position over high-pile carpet, over linoleum, and up a ramp with a 5 degrees incline while propulsion kinematics and kinetics were recorded with a motion capture system and an instrumented wheel. Three raters classified the first 3 strokes as 1 of 4 types on each surface: arc, semicircular (SC), single looping over propulsion (SL), and double looping over propulsion (DL). The Fisher exact test was used to assess pattern changes between strokes and surface type. A multiple analysis of variance test was used to compare peak and average resultant force and moment about the hub, average wheel velocity, stroke frequency, contact angle, and distance traveled between stroke patterns. SL was the most common pattern used during start-up propulsion (44.9%), followed by arc (35.9%), DL (14.1%), and SC (5.1%). Subjects who dropped their hands below the rim during recovery achieved faster velocities and covered greater distances (.016propulsion patterns is a difficult task that should use multiple raters. In addition, propulsion patterns change during start-up, with an arc pattern most prevalent initially. The biomechanical findings in this study agree with current clinical guidelines that recommend training users to drop the hand below the pushrim during recovery.

Construction, start-up and operation of Dukovany nuclear power plant

International Nuclear Information System (INIS)

Hornicek, Z.

1989-01-01

The Labor Safety Inspectorate have been supervising the construction of the Dukovany nuclear power plant since the construction start in 1977. It was found that in concreting the reactor building walls with concrete mixes, the regulations were not observed on the highest level for the concrete mix drop, and on the gap processing and concrete treatment when concreting was interrupted. Thus, concreting was halted until the conditions for concreting were met. Attention was focused on the protection of the hermetic casing from damage, which had very often happened. A number of shortcomings were detected in storing technology parts. The cleanliness was inspected of the facilities being assembled. The inspections also revealed shortcomings in sealed space tightness. The inspections of assembly and testing of facilities showed failures of the facilities themselves (control valves, electric motors, filter and pump sealing) and of the assembly process. Faults were also detected in electrical equipment. Only a very small part of the installation showed lifetime as specified by Decree 105/1982 Coll. laws on safety assurance in the nuclear power industry. Missing data in documentation led to delays in the start-up stages. The State Surveillance Body also inspected the results of equipment testing. Prior to physical start-up, all production facilities and buildings were inspected, labor safety was inspected for all personnel in communicating corridors, staircases, manholes and onservice and handling posts. Shortcomings were removed. The organization of assembly work was a considerable problem if staff from more organizations had to work together in the same workplace. A list of tasks is presented of State Surveillance Body in operation, maintenance, outages, repairs, and troubleshooting in a nuclear power plant. (J.B.)

Effects of school start time on students' sleep duration, daytime sleepiness, and attendance: a meta-analysis.

Science.gov (United States)

Bowers, Jennifer M; Moyer, Anne

2017-12-01

Research conducted over the past three decades finds that many children and adolescents do not meet recommended sleep guidelines. Lack of sleep is a predictor of a number of consequences, including issues at school such as sleepiness and tardiness. Considering the severity of this public health issue, it is essential to understand more about the factors that may compromise children's and adolescents' sleep. This meta-analysis examined the effects of school start time (SST) on sleep duration of students by aggregating the results of five longitudinal studies and 15 cross-sectional comparison group studies. Results indicated that later starting school times are associated with longer sleep durations. Additionally, later start times were associated with less daytime sleepiness (7 studies) and tardiness to school (3 studies). However, methodological considerations, such as a need for more longitudinal primary research, lead to a cautious interpretation. Overall, this systematic analysis of SST studies suggests that delaying SST is associated with benefits for students' sleep and, thus, their general well-being. Copyright © 2017 National Sleep Foundation. Published by Elsevier Inc. All rights reserved.

>venture>: Support for Early Stage Start-ups and Potential Entrepreneurs.

Science.gov (United States)

Kauz, Lukas

2014-12-01

>venture>, the leading Swiss-wide business plan competition, is an ideal partner for young start-ups and entrepreneurs. For the upcoming tenth anniversary edition the competition will receive an update. Building upon a successful base of the past nine editions and equipped with contemporary networking events and more know-how transferring seminars, >venture> will fit even better into the Swiss start-up ecosystem.

Parental Book Reading and Social-Emotional Outcomes for Head Start Children in Foster Care.

Science.gov (United States)

Lee, Kyunghee; Lee, Jung-Sook

2016-01-01

This study examines the associations between parental book reading and social-emotional outcomes for Head Start children in foster care. Despite no main Head Start impact on parental book reading, subgroup effects were found. Foster parents in Head Start provided more book reading for children with disabilities but less for children with low preacademic scores. Head Start enhanced social-emotional outcomes for children in foster care. The positive impacts of Head Start on children's social-emotional outcomes were greater when parents read books frequently. Head Start should include more foster families and provided parenting skills to enhance social-emotional outcomes for children in foster care.

A novel start-up procedure for natural-circulation boiling water reactors

International Nuclear Information System (INIS)

Annalisa Manera; Frank Schaefer

2005-01-01

Valves). In this case steam is generated due to flashing at high pressure. The simulation by means of TRACG shows that no flow oscillations occur during the transition from single- to two-phase operation. A similar start-up procedure is simulated by Cheng and coauthors [4] by means of the code RAMONA-4B. They find contradicting results compared to the one obtained by Cheung and Rao. However, RAMONA-4B cannot predict the occurrence of flashing at low pressures, since a single average system pressure is used by this code to calculate thermodynamic properties of water and steam in the system. Therefore, the results obtained by this code are meaningless with regard to the start-up of natural circulation two-phase systems. In the present work a novel start-up procedure will be illustrated which does not require any additional system and in which there is no necessity for an abrupt steam production at high pressure [5], as in the procedure of Cheung and Rao. In the procedure proposed in this work, the reactor vessel is pressurized by means of steam produced in the reactor vessel itself, but outside the core and riser section. In this way, the system can be pressurized while the reactor still operates in single-phase conditions, thus without occurrence of flashing-induced flow oscillations. At the same time, a smooth steam production and pressurization of the system is achieved. The feasibility of the intermediate state in which steam is produced in the reactor vessel while the circulation in core and riser sections remains single-phase has been already proved during an experimental campaign performed at the large-scale facility PANDA. The procedure is simulated by means of the ATHLET code, developed by GRS (Germany). This code has been successfully qualified against low-pressure flashing-induced instabilities within the framework of the EU project NACUSP. (authors)

Start-up of plasma current by electron Bernstein wave

International Nuclear Information System (INIS)

Maekawa, Takashi; Tanaka, Hitoshi; Uehide, Masaki

2009-01-01

Electron cyclotron current drive by electron Bernstein (EB) waves for the start-up and ramp-up of toroidal plasma current with no central solenoid in tokamaks is discussed. It is shown that high N// EB waves have ability to ramp-up the current against the counter voltage from self-induction, where N// is the parallel refractive index to the magnetic field, and they are especially suitable for initial current start-up phase where the bulk electron temperature is low enough to ensure high N// EB waves. (author)

Association between Duration of Predialysis Care and Mortality after Dialysis Start.

Science.gov (United States)

Liu, Ping; Quinn, Robert R; Oliver, Matthew J; Ronksley, Paul E; Hemmelgarn, Brenda R; Quan, Hude; Hiremath, Swapnil; Bello, Aminu K; Blake, Peter G; Garg, Amit X; Johnson, John; Verrelli, Mauro; Zacharias, James M; Abd ElHafeez, Samar; Tonelli, Marcello; Ravani, Pietro

2018-03-05

Early nephrology referral is recommended for people with CKD on the basis of observational studies showing that longer nephrology care before dialysis start (predialysis care) is associated with lower mortality after dialysis start. This association may be observed because predialysis care truly reduces mortality or because healthier people with an uncomplicated course of disease will have both longer predialysis care and lower risk for death. We examined whether the survival benefit of longer predialysis care exists after accounting for the potential confounding effect of disease course that may also be affected by predialysis care. We performed a retrospective cohort study and used data from 3152 adults with end stage kidney failure starting dialysis between 2004 and 2014 in five Canadian dialysis programs. We obtained duration of predialysis care from the earliest nephrology outpatient visit to dialysis start; markers of disease course, including inpatient or outpatient dialysis start and residual kidney function around dialysis start; and all-cause mortality after dialysis start. The percentages of participants with 0, 1-119, 120-364, and ≥365 days of predialysis care were 23%, 8%, 10%, and 59%, respectively. When we ignored markers of disease course as in previous studies, longer predialysis care was associated with lower mortality (hazard ratio 120-364 versus 0-119 days , 0.60; 95% confidence interval, 0.46 to 0.78]; hazard ratio ≥365 versus 0-119 days , 0.60; 95% confidence interval, 0.51 to 0.71; standard Cox model adjusted for demographics and laboratory and clinical characteristics). When we additionally accounted for markers of disease course using the inverse probability of treatment weighted Cox model, this association was weaker and no longer significant (hazard ratio 120-364 versus 0-119 days , 0.84; 95% confidence interval, 0.60 to 1.18; hazard ratio ≥365 versus 0-119 days , 0.88; 95% confidence interval, 0.69 to 1.13). The association between

Caregivers' attitudes regarding portion sizes served to children at Head Start

Science.gov (United States)

Head Start caregivers are responsible for educating and feeding preschoolers enrolled in the Head Start program. Amongst pre-school aged children, portion size served is positively associated with intake of those foods. Researchers conducted eight focus groups with Hispanic and African American Head...

Model citizens. Outsourcing helps start-up Medicare HMO.

Science.gov (United States)

Slavic, B; Adami, S

1999-04-01

Health Plans of Pennsylvania (HPP), the managed care arm of Crozer-Keystone Health System, in Media, Pa. Selecting the information systems and building the infrastructure to support the start-up of a new Medicare HMO product. HPP chose to outsource the information systems needed to integrate all the components of managed care administration into a cost-effective and cohesive program. Because of its aggressive programming and start-up of the MedCarePlus product offering, HPP became the first plan in the country to submit Medicare claims data electronically for encounter reporting to the Health Care Financing Administration (HCFA). "Through an integrated team approach, an organization truly can benefit from the economies of scale gained through outsourcing."

Organising a conference? Think about what you can do for start-ups!

CERN Multimedia

David Mazur

2016-01-01

ICTR-PHE 2016 welcomed 16 exhibitors and sponsors as part of its industrial exhibition. If you have ever (co-)organised a large scientific conference, you almost certainly have your own list of major industrial actors who could be interested in becoming exhibitors or sponsors.   The six start-ups present at ICTR-PHE 2016 – Oncoradiomics, Colnec Health, Dixit Solutions, e-Learning4Health, I-See Computing and SmART Scientific Solutions (not pictured). (Image: Salvatore Fiore) ICTR-PHE has shown that scientific conferences can have a catalysing role in transforming young start-ups and spin-off companies into the key industrial players of tomorrow. A special start-up corner was provided in the industrial exhibition, where small stands were made available for a modest fee to start-ups and spin-off companies in fields relevant to the conference theme, together with a 5-minute timeslot for a pitch to the audience. Six start-ups, from the Netherlands, Italy and France...

Starting up a Firm or Not: Differences in the Antecedents of Entrepreneurial Intentions

Science.gov (United States)

Varamäki, Elina; Joensuu, Sanna; Viljamaa, Anmari

2016-01-01

Entrepreneurial intentions (EIs) and their antecedents have been extensively studied in student populations. The results suggest that higher education does not promote the formation of EI in students. This article examines the antecedents of intentions in two different student populations: those who are currently starting a firm and those who are…

START: an advanced radiation therapy information system.

Science.gov (United States)

Cocco, A; Valentini, V; Balducci, M; Mantello, G

1996-01-01