WorldWideScience

Sample records for starch gum

  1. Extrudates of starch-xanthan gum mixtures as affected by chemical agents and irradiation

    International Nuclear Information System (INIS)

    Hanna, M.A.; Chinnaswamy, R.; Gray, D.R.; Miladinov, V.D.

    1997-01-01

    Mixtures of starch, xanthan gum and either polyvinyl alcohol, epichlorohydrin, valeric acid or adipoyl chloride were extruded. Properties of extrudates including apparent viscosity, water solubility, water absorption indices and extrudate expansion were measured for different proportions of xanthan gum, 70% amylose starch (with or without irradiation) and chemical agents. Extrusion with chemical agents and irradiation changed physical properties of both starch and xanthan gum. Expansions of extrudates were higher than that of starch. Viscosity of extrudates increased with xanthan gum concentration. The addition of 1% (w/w) polyvinyl alcohol had the greatest effect of the chemical agents. Irradiation increased the apparent viscosity of starch-xanthan gum mixtures

  2. Effect of guar and xanthan gums on functional properties of mango (Mangifera indica) kernel starch.

    Science.gov (United States)

    Nawab, Anjum; Alam, Feroz; Haq, Muhammad Abdul; Hasnain, Abid

    2016-12-01

    The effects of different concentrations of guar and xanthan gums on functional properties of mango kernel starch (MKS) were studied. Both guar and xanthan gum enhanced the water absorption of MKS. The addition of xanthan gum appeared to reduce the SP (swelling power) and solubility at higher temperatures while guar gum significantly enhanced the SP as well as solubility of MKS. The addition of both gums produced a reinforcing effect on peak viscosity of MKS as compared to control. Pasting temperature of MKS was higher than that of starch modified by gums indicating ease of gelatinization. Guar gum played an accelerative effect on setback but xanthan gum delayed the setback phenomenon during the cooling of the starch paste. Both gums were found to be effective in reducing the syneresis while gel firmness was markedly improved. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Mango kernel starch-gum composite films: Physical, mechanical and barrier properties.

    Science.gov (United States)

    Nawab, Anjum; Alam, Feroz; Haq, Muhammad Abdul; Lutfi, Zubala; Hasnain, Abid

    2017-05-01

    Composite films were developed by the casting method using mango kernel starch (MKS) and guar and xanthan gums. The concentration of both gums ranged from 0% to 30% (w/w of starch; db). Mechanical properties, oxygen permeability (OP), water vapor permeability (WVP), solubility in water and color parameters of composite films were evaluated. The crystallinity and homogeneity between the starch and gums were also evaluated by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The scanning electron micrographs showed homogeneous matrix, with no signs of phase separation between the components. XRD analysis demonstrated diminished crystalline peak. Regardless of gum type the tensile strength (TS) of composite films increased with increasing gum concentration while reverse trend was noted for elongation at break (EAB) which found to be decreased with increasing gum concentration. The addition of both guar and xanthan gums increased solubility and WVP of the composite films. However, the OP was found to be lower than that of the control with both gums. Furthermore, addition of both gums led to changes in transparency and opacity of MKS films. Films containing 10% (w/w) xanthan gum showed lower values for solubility, WVP and OP, while film containing 20% guar gum showed good mechanical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Effect of Acacia Gum, NaCl, and Sucrose on Physical Properties of Lotus Stem Starch

    Science.gov (United States)

    Gill, Balmeet Singh

    2014-01-01

    Consumer preferences in east Asian part of the world pave the way for consumption of lotus stem starch (LSS) in preparations such as breakfast meals, fast foods, and traditional confectioneries. The present study envisaged the investigation and optimization of additives, that is, acacia gum, sodium chloride (NaCl), and sucrose, on water absorption (WA), water absorption index (WAI), and water solubility index (WSI) of LSS employing response surface methodology (RSM). Acacia gum resulted in increased water uptake and swelling of starch; however, NaCl reduced the swelling power of starch by making water unavailable to starch and also due to starch-ion electrostatic interaction. Sucrose restricted the water absorption by binding free water and decreased amylose leaching by building bridges with starch chains and thus forming rigid structure. PMID:26904639

  5. The Effect of Three Gums on the Retrogradation of Indica Rice Starch

    Directory of Open Access Journals (Sweden)

    Bin Li

    2012-05-01

    Full Text Available Retrograded starch (RS3 was produced from indica rice starch with three kinds of gums (konjac glucomannan, KGM; carrageenan, CA, USA; and gellan, GA, USA by autoclaving, respectively, and the effect of the gums on the retrogradation behavior of starch was estimated. The influences of polysaccharide concentration, sodium chloride concentration, autoclaving time, refrigerated time, and pH value on RS3 formation were discussed. Except for sodium chloride’s persistent restraint on RS3, the others all forced RS3 yields higher at first, but lowered it after the peak value. The influencing sequence of these impact factors was: sodium chloride concentration > polysaccharide concentration > autoclaving time > refrigerated time > pH value. The results also proved that in the three gums, KGM plays the most significant role in RS3 changing. It was concluded that the incorporation of each of these three gums into starch, especially KGM, results in an increase or decrease of RS3 under different conditions. This phenomenon could be taken into consideration when developing starchy food with appropriate amount of RS3.

  6. MICROENCAPSULATION OF TURMERIC OLEORESIN IN BINARY AND TERNARY BLENDS OF GUM ARABIC, MALTODEXTRIN AND MODIFIED STARCH

    Directory of Open Access Journals (Sweden)

    Diana Maria Cano-Higuita

    2015-04-01

    Full Text Available Spray-drying is a suitable method to obtain microencapsulated active substances in the powdered form, resulting in powders with improved protection against environmental factors as well as with higher solubility in water, as in the case of turmeric oleoresin. The present study investigated the spray-drying process of turmeric oleoresin microencapsulated with binary and ternary mixtures of different wall materials: gum Arabic, maltodextrin, and modified corn starch. A statistical simplex centroid experimental design was used considering the encapsulation efficiency, curcumin retention, process yield, water content, solubility, and particle morphology as the analyzed responses. Wall matrices containing higher proportions of modified starch and gum Arabic resulted in higher encapsulation efficiency and curcumin retention, whereas the process yield and water content increased with higher proportions of maltodextrin and gum Arabic, respectively. Regression models of the responses were obtained using a surface response method (ANOVA way, showing statistical values of R2 > 0.790. Also, mean analysis was carried out by Tukey's test, permitting to observe some statistical differences between the blends

  7. A comparison of the stability of beverage cloud emulsions formulated with different gum acacia- and starch-based emulsifiers.

    Science.gov (United States)

    Reiner, S J; Reineccius, G A; Peppard, T L

    2010-06-01

    The performance of several hydrocolloids (3 gum acacias, 1 modified gum acacia, and 3 modified starches) in stabilizing beverage emulsions and corresponding model beverages was investigated employing different core materials, emulsifier usage levels, and storage temperatures. Concentrated emulsions were prepared using orange terpenes or Miglyol 812 (comprising medium-chain triglycerides, MCT) weighted 1:1 with ester gum, stored at 25 or 35 degrees C, and analyzed on days 0, 1, and 3. On day 3, model beverages were made from each emulsion, stored at both temperatures, and analyzed weekly for 4 wk. Stability of concentrated emulsions was assessed by measuring mean particle size and by visual observations of ringing; beverage stability was judged similarly and also by loss of turbidity. Particle size measurements showed concentrated emulsions containing gum acacia or modified gum acacia with either core material were stable over 3 d storage at both temperatures whereas those made with modified starches were not, destabilization being faster at 35 degrees C. Beverages based on orange terpenes, in contrast to Miglyol, yielded smaller mean particle sizes, both on manufacture and during storage, regardless of hydrocolloid used. Visual observations of ringing generally supported this finding. Modified gum acacia was evaluated at both recommended and higher usage levels, stability increasing in the latter case. In general, all gum acacia and modified gum acacia emulsifiers were superior in stability to those based on modified starches, at either temperature, for orange terpene-based beverages. In Miglyol-based beverages, similar results were seen, except 1 modified starch performed as well as the gum acacia products.

  8. Sifat Fisik Pati Ganyong (Canna edulis Kerr. Termodifikasi dan Penambahan Gum Xanthan untuk Rerotian (Physical Characteristics of Modified Canna edulis Kerr. Starch and Gum Xanthan for Bakeries

    Directory of Open Access Journals (Sweden)

    Parwiyanti Parwiyanti

    2016-12-01

    Full Text Available Modification of Canna starch through heat-moisture treatment (HMT and gum xanthan (GX treatment was conducted to improve the disadvantage of natural Canna starch in order to expand its usage in food industry, especially for bakery products. The research was arranged in a factorial randomized complete block design with three factors (temperature, incubation time, and GX concentrations and three replications for each factor.  The modified Canna  starch by HMT possessed water content of 15 % as well as combination of temperature (80 °C and 100 °C, periods (8 and 16 hours and concentration of GX (0; 0.5; 1; 1.5 and 2 %. The observed variables were the swelling power, water solubility index, water absorption index, baking expantion, and bulk density of modified Canna starch. The result showed that the modification of Canna starch by temperature, time of HMT and concentration GX produced modified starch with physical properties that significantly differ among treatments and natural starch.  Modified Canna starch by treatments of 80 °C, 8 hours, and 1 % xanthan gum concentration showed had swelling power 16.90 ± 0.48 g/g, water solubility index 10.28 ± 0.25 %, water absorption index 112.58 ± 0.38 %, baking expantion 0.94 ± 0.11 mL/g and bulk density 0.73 ± 0.026 g/mL which alike with wheat flour so that it can be further developed as wheat flour substitute on bakery products.   ABSTRAK Penelitian modifikasi pati ganyong melalui perlakuan heat-moisture-treatment (HMT dan penambahan gum xanthan (GX dilakukan untuk memperbaiki kelemahan pati ganyong alami sehingga menjadi luas aplikasinya dalam industri pangan terutama produk rerotian.  Penelitian menggunakan rancangan acak kelompok faktorial dengan 3 perlakukan dan 3 ulangan.  Perlakuan yang diberikan adalah waktu (8 dan 16 jam, suhu (80 °C dan 100 °C, kadar air 15 % dan konsentrasi gum xanthan (0, 0,5; 1; 1,5; 2 %.  Data dianalisis dengan sidik ragam (ANOVA pada α = 0,05, dilanjutkan

  9. Artocarpus heterophyllus L. seed starch-blended gellan gum mucoadhesive beads of metformin HCl.

    Science.gov (United States)

    Nayak, Amit Kumar; Pal, Dilipkumar; Santra, Kousik

    2014-04-01

    Jackfruit (Artocarpus heterophyllus Lam., family: Moraceae) seed starch (JFSS)-gellan gum (GG) mucoadhesive beads containing metformin HCl were developed through ionotropic gelation technique. The effect of GG to JFSS ratio and CaCl2 concentration on the drug encapsulation efficiency (DEE, %) and cumulative drug release at 10h (R10h, %) was optimized and analyzed using response surface methodology based on 3(2) factorial design. The optimized JFSS-GG beads containing metformin HCl showed DEE of 92.67±4.46%, R10h of 61.30±2.37%, and mean diameter of 1.67±0.27 mm. The optimized beads showed pH-dependent swelling and mucoadhesivity with the goat intestinal mucosa. The in vitro drug release from all these JFSS-GG beads containing metformin HCl was followed zero-order pattern (R(2)=0.9907-0.9975) with super case-II transport mechanism over a period of 10 h. The beads were also characterized by SEM and FTIR. The optimized JFSS-GG beads containing metformin HCl exhibited significant hypoglycemic effect in alloxan-induced diabetic rats over prolonged period after oral administration. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. A Comparative Study Between Modified Starch and Xanthan Gum Thickeners in Post-Stroke Oropharyngeal Dysphagia.

    Science.gov (United States)

    Vilardell, N; Rofes, L; Arreola, V; Speyer, R; Clavé, P

    2016-04-01

    Thickeners are used in post-stroke oropharyngeal dysphagia (OD) as a compensatory therapeutic strategy against aspirations. To compare the therapeutic effects of modified starch (MS) and xanthan gum (XG) thickeners on swallow safety and efficacy in chronic post-stroke OD patients using clinical and videofluoroscopic (VFS) assessment. Patients were studied by clinical assessment (volume-viscosity swallow test, V-VST) and VFS using 3 volumes (5, 10, 20 mL) and 3 viscosities (liquid, nectar and spoon thick), comparing MS and XG. We studied 122 patients (46MS, 76XG). (A) V-VST showed that both thickeners similarly improved safety of swallow. Prevalence of safe swallowing significantly increased with enhanced viscosity (P < 0.001 vs liquid), MS: 47.83 % at liquid, 84.93 % at nectar and 92.96 % at spoon thick; XG: 55.31 % at liquid, 77.78 % at nectar and 97.84 % at spoon thick. Patients on MS reported higher prevalence of pharyngeal residue at spoon-thick viscosities. (B) VFS: increasing bolus viscosity with either thickener increased prevalence of safe swallows (P < 0.001 vs liquid), MS: 30.25 % liquid, 61.07 % nectar and 92.64 % spoon thick; XG: 29.12 % liquid, 71.30 % nectar and 89.91 % spoon thick. Penetration-aspiration scale score was significantly reduced with increased viscosity with both thickeners. MS increased oral and pharyngeal residues at nectar and spoon-thick viscosities but XG did not. Timing of airway protection mechanisms and bolus velocity were not affected by either thickener. Increasing bolus viscosity with MS and XG thickeners strongly and similarly improved safety of swallow in chronic post-stroke OD by a compensatory mechanism; in contrast only MS thickeners increased oropharyngeal residue.

  11. Antimicrobial activities of tapioca starch/decolorized hsian-tsao leaf gum coatings containing green tea extracts in fruit-based salads, romaine hearts and pork slices.

    Science.gov (United States)

    Chiu, Po-En; Lai, Lih-Shiuh

    2010-04-30

    The antimicrobial activities of edible coatings based on a tapioca starch/decolorized hsian-tsao leaf gum (dHG) matrix with various green tea extracts (GTEs) were evaluated. Its effect on the shelf-life extension of fruit-based salads, romaine hearts, and pork slices were investigated as well. Three types of GTEs from hot water (80 degrees C) (W), 40% (E4) and 80% (E8) ethanol were prepared. It was found that all GTEs showed pronounced inhibition on Gram positive bacteria in agar media, including Staphylococcus aureus BCRC 10781, Bacillus cereus BCRC 11778 and Listeria monocytogenes BCRC 14848, but not on Gram negative bacteria, such as Escherichia coli DH10beta and Salmonella enteria BCRC 10747. The antimicrobial activities increased with increasing GTEs concentration (1, 2 and 5%), but did not differentiate significantly in terms of the effect of extraction solvents. When various GTEs (1%) were added to an edible coating formulation based on 1.35% tapioca starch +0.15% dHG +0.225% glycerol, pronounced antimicrobial activity on Gram positive bacteria was also observed as evaluated by using cylinder diffusion and antimicrobial migration tests. It was believed that the active compounds in green tea extracts could leave the coating matrix and migrate to increase the non-growth area. When being sprayed on various real food models, all tapioca starch/dHG coatings containing GTEs could successfully reduce the aerobic counting and growth of yeasts/molds by 1 to 2 log cycles in fruit-based salads, as compared to the control sample. Furthermore, during refrigerated storage of romaine hearts and pork slices for 48h, tapioca starch/dHG coatings with E4 extracts demonstrated pronounced antimicrobial activity against Gram positive bacteria (4-6 log cycles reduction), followed by W extracts and E8 extracts in a decreasing order. Such results implied the high efficacy of antimicrobial migration of tapioca starch/dHG coatings containing GTEs and their application potentials on

  12. Propriedades de barreira e solubilidade de filmes de amido de ervilha associado com goma xantana e glicerol Barrier properties of films of pea starch associated with xanthan gum and glycerol

    Directory of Open Access Journals (Sweden)

    Manoel D. da Matta Jr

    2011-01-01

    Full Text Available O objetivo do trabalho foi avaliar as propriedades de barreira e a solubilidade de biofilmes obtidos a partir de amido de ervilha de alto teor de amilose em associação à goma xantana e glicerol. Soluções filmogênicas (SF com diferentes teores de amido de ervilha (3, 4 e 5%, goma xantana (0, 0,05 e 0,1% e glicerol (proporção glicerol-amido de 1:5 P/P foram estudadas. As SF foram obtidas por ebulição (5 minutos, seguida de autoclavagem por 1 hora a 120 ºC e os filmes foram preparados por casting. O aumento da concentração de amido e de glicerol na composição causou aumento da espessura e da solubilidade dos filmes em água. O plastificante gerou ainda elevação dos coeficientes de permeabilidade ao vapor d'água e ao oxigênio. O aumento da concentração da goma xantana não interferiu nas propriedades estudadas. Os biofilmes obtidos a partir de amido de ervilha verde, associado ou não à goma xantana e glicerol, se comparados com filmes de amido de ervilha amarelas e outras fontes de amido, apresentaram boa barreira ao oxigênio e ao vapor d'água e baixa solubilidade em água.The aim of this work was to evaluate the barrier properties and solubility of biofilms made from wrinkled pea starch with high amylose content in association with xanthan gum and glycerol. Filmogenic solution (FS with different levels of pea starch (3, 4 and 5%, xanthan gum (0, 0.05 and 0.1% and glycerol (glycerol-starch 1:5 W/W were tested. FS was obtained by boiling (5 minutes, autoclaving for 1 hour at 120 ºC and the films were prepared by casting. The increased concentration of starch and glycerol in the composition caused increases in thickness of the films and in their solubility in water. The plasticizer also generated higher coefficients of water vapor and oxygen permeabilities to water vapor and to oxygen. The increasing concentration of xanthan gum did not interfere in the properties studied. Biofilms produced with wrinkled pea starch, with or

  13. Xanthan gum production by Xanthomonas campestris pv ...

    African Journals Online (AJOL)

    Cassava starch is a main renewable bio-resource with low price and mass production in Guangxi, China. It was used as carbon source in growing Xanthomonas campestris pv. campestris 8004 (Xcc 8004) for xanthan gum production in this study. The xanthan gum yield of gelatinized cassava starch was higher than that of ...

  14. gum production by Xanthomonas campestris pv

    African Journals Online (AJOL)

    DR TONUKARI NYEROVWO

    2012-09-11

    Sep 11, 2012 ... 8004) for xanthan gum production in this study. ... strain for xanthan gum production using cassava starch in industrial applications. ... the cassava price is cost-effective relative to other ... For amylase activity determination, a crude enzyme sample (1 ml) .... time point to stop fermentation from an economic.

  15. Gum Disease

    Science.gov (United States)

    ... and gums isn't removed by good daily dental care, over time it will harden into a crust called calculus or tartar . Once tartar forms, it starts to destroy gum tissue, causing gums to bleed and pull away from the teeth. This is known as periodontitis (pronounced: pair-ee- ...

  16. Hydrolyzed collagen, modified starch and guar gum addition in turkey ham Adição de colágeno hidrolisado, amido modificado e goma guar em presunto de peru

    Directory of Open Access Journals (Sweden)

    Rosa Cristina Prestes

    2012-07-01

    Full Text Available The main problems observed in cooked hams are bad sliceability and excessive fluid loss after cooking. To reduce these problems the industry uses non-meat ingredients such as soy protein and carrageenan, but under Brazilian law, it is not allowed to add starch or modified starch in hams. Three ingredients were tested in the present research: modified starch (0 to 2.0%, gum guar (0 to 0.30% and hydrolyzed collagen (0 to 2.0%, following a 2³ full factorial design with five repetitions in the central point. The guar gum produced low resistance to reheating, however in losses by cooling, the results were adequate. The hydrolyzed collagen tested did not give satisfactory results, showing low acceptance due to formation of gel in the ham and high losses. The developed products were not different from the commercial product in relation to texture (P>0.05. The formulation F6 (2.0% of modified starch was the one with the best results and greater acceptance as detected by the tasters. Based on the results obtained it seems appropriate to propose the legal permission of starch in ham or the creation of a new class of product in which starch addition would be allowed.Os principais problemas observados em presuntos são a má fatiabilidade e a perda excessiva de líquidos após o cozimento. Para reduzir esses problemas, a indústria utiliza ingredientes não cárneos, tais como a proteína de soja e a carragena, porém, segundo a legislação brasileira, não é permitida a adição de amido ou amido modificado. Neste trabalho, foram testados três ingredientes, em presunto cozido de peru: amido modificado (0 a 2,0%, goma guar (0 a 0,30% e colágeno hidrolisado (0 a 2,0%, seguindo um delineamento fatorial completo 2³ com cinco repetições no ponto central. A goma guar apresentou baixa resistência ao reaquecimento, no entanto, nas perdas por resfriamento, os resultados foram adequados. O colágeno hidrolisado testado não proporcionou resultados satisfat

  17. Tragacanth gum

    DEFF Research Database (Denmark)

    Meyer, Anne S.; Mikkelsen, Jørn Dalgaard; Gavlighi, Hassan Ahmadi

    2013-01-01

    highly substituted pectin-like structural elements. Enzymatically produced low molecular- weight fractions of tragacanth gum exhibit potential prebiotic activity by promoting growth in vitro of Bifidobacterium longum subsp. infantis strains. These findings may lead to new uses of this gum for production...... of value-added prebiotic compounds for functional foods....

  18. Funcionalidade da oleoresina de páprica microencapsulada em goma-arábica e amido de arroz/gelatina Functionality of microencapsulated paprika oleoresin in arabic gum and rice starch/gelatin

    Directory of Open Access Journals (Sweden)

    Andréa Barbosa Santos

    2006-02-01

    Full Text Available O objetivo deste trabalho foi avaliar a funcionalidade da oleoresina de páprica microencapsulada em goma-arábica e amido de arroz/gelatina, incorporada nos sistemas-modelo bolo e gel de gelatina. Avaliou-se a cor por meio de medida instrumental e aceitação sensorial por atributos de aparência e aceitação global. O pigmento encapsulado solubilizou-se, tingiu e se distribuiu uniformemente nos bolos, os quais apresentaram boa aceitação global. Nos géis, a goma apresentou desempenho superior ao amido/gelatina quanto à aparência, porém, todos os tratamentos obtiveram baixa aceitação global. A presença da oleoresina microencapsulada não interferiu negativamente no sabor, aroma ou textura dos sistemas analisados.The objective of this work was to evaluate the functionality of microencapsulated paprika oleoresin in arabic gum and rice starch/gelatin incorporated into the model systems: cake and gelatin gel. The systems were evaluated by instrumental color and consumer test based on the appearance and global acceptance attributes. The encapsulated pigment successfully dyed the cakes as well as was uniformly distributed into the products, showing good sensory acceptance. In the gels, a superior performance was obtained when using arabic gum, however all treatments applied for gels showed low global sensory acceptance. The presence of microencapsulated paprika oleoresin had no negative effect on taste, flavor or texture of analyzed systems.

  19. Nicotine Gum

    Science.gov (United States)

    ... with a smoking cessation program, which may include support groups, counseling, or specific behavioral change techniques. Nicotine gum ... and pharmacist what prescription and nonprescription medications, vitamins, nutritional supplements, and herbal products you are taking or ...

  20. Estabilidade de géis de amido de milho normal, ceroso e com alto teor de amilose adicionados de gomas guar e xantana durante os processos de congelamento e descongelamento Freeze-thaw stability of normal, waxy and high amylose corn starch gels with added guar and xanthan gums

    Directory of Open Access Journals (Sweden)

    Fernanda Hart Weber

    2008-06-01

    Full Text Available O objetivo do presente trabalho foi estudar os efeitos das gomas guar e xantana sobre a estabilidade dos géis de amido de milho normal, ceroso e com alto teor de amilose submetidos aos processos de congelamento e descongelamento. Os géis desses amidos, com concentração total de sólidos de 10% e adicionados das gomas (0,15; 0,50; 0,85 e 1%, foram submetidos a 5 ciclos de congelamento (20 horas a -18 °C e descongelamento (4 horas a 25 °C, com exceção dos géis com alto teor de amilose, que foram submetidos a apenas 1 ciclo, devido à perda da estrutura de gel. A determinação da sinérese (porcentagem de água liberada foi realizada pela diferença entre a massa inicial e a massa final das amostras. O gel de amido de milho normal liberou 74,45% de água, sendo que a adição de 1% da goma xantana reduziu significativamente a sinérese para 66,43%. A adição de 0,85 e 1% da goma xantana também reduziu a sinérese dos géis de amido ceroso. O menor teor de sinérese foi obtido com a utilização de 1% de goma xantana ao gel de amido de milho com alto teor de amilose, evidenciando a ação crioprotetora desta goma.The objective of the present work was to study the effects of guar and xanthan gums on the stability of normal, waxy and high amylose corn starch gels, submitted to freeze-thaw processes. The gels of these starches with a total solids content of 10% and added gums (0.15;0.50;0.85and1%, were submitted to 5 freezing (20 hours, -18 °C and thawing (4 hours, 25 °C cycles, with exception of the high amylose gels that were submitted to only 1 cycle. Syneresis (% water released was determined by the difference between the initial and final masses of the samples. The normal corn starch gel released 74.45% water and the addition of 1% xanthan gum significantly reduced syneresis to 66.43%. The incorporation of 0.85 and 1% xanthan gum also reduced syneresis of waxy starch gels. The lowest level of syneresis was reached with the use of 1

  1. Effect of addition of different hydrocolloids on pasting, thermal, and rheological properties of cassava starch

    Directory of Open Access Journals (Sweden)

    Tatiana Dias Leite

    2012-09-01

    Full Text Available Starches and gums are hydrocolloids frequently used in food systems to provide proper texture, moisture, and water mobility. Starch-gum interaction in food systems can change the starch granule swelling and its gelatinization and rheological properties. In this study, the effect of the addition of xanthan gum (XG, sodium carboxymethyl cellulose (SCMC, and carrageenan (CAR at the concentrations of the 0.15, 0.25, 0.35 and 0.45% (w/v on the pasting, thermal, and rheological properties of cassava starch was studied. The swelling power (SP and the scanning electron microscopy (SEM of the starch gels were also evaluated. The results obtained showed that xanthan gum (XG had a strong interaction with the cassava starch penetrating between starch granules causing increase in pasting viscosities, SP, storage and loss (G', and G", respectively modulus and reduction in the setback of the starch; sodium carboxymethyl cellulose (SCMC greatly increased the pasting viscosities, the SP, and the storage and loss (G', and G", respectively modulus of the starch-mixtures, mainly due to its greater capacity to hold water and not due to the interaction with cassava starch. Carrageenan (CAR did not change any of the starch properties since there was no interaction between this gum and cassava starch at the concentrations used.

  2. Analysis of a gum from the exudates of Dichrostachys cinerea (L ...

    African Journals Online (AJOL)

    Jane

    2011-07-06

    Jul 6, 2011 ... In conclusion, this gum has potential as a product for the cosmetic, .... Care was taken that no black or grey specks remained conspicuous in the ..... properties of chemically modified rice starch model solutions. J. Food.

  3. Starch bioengineering

    DEFF Research Database (Denmark)

    Blennow, Andreas

    2018-01-01

    Application of starch in industry frequently requires extensive modification. This is usually achieved by chemical and/or physical modification that is time-consuming and often expensive and polluting. To impart functionality as early as possible in the starch production chain, modification can...... be achieved directly as part of the developing starch storage roots, tubers, and seeds and grains of the crop. Starch has been a strong driver for human development and is now the most important energy provider in the diet forcing the development of novel and valuable starch qualities for specific...... applications. Among the most important structures that can be targeted include starch phosphorylation chain transfer/branching generating chemically substituted and chain length-modified starches such as resistant and health-promoting high-amylose starch. Starch bioengineering has been employed for more than...

  4. Immune reactivities against gums.

    Science.gov (United States)

    Vojdani, Aristo; Vojdani, Charlene

    2015-01-01

    Different kinds of gums from various sources enjoy an extremely broad range of commercial and industrial use, from food and pharmaceuticals to printing and adhesives. Although generally recognized as safe by the US Food and Drug Administration (FDA), gums have a history of association with sensitive or allergic reactions. In addition, studies have shown that gums have a structural, molecular similarity to a number of common foods. A possibility exists for cross-reactivity. Due to the widespread use of gums in almost every aspect of modern life, the overall goal of the current investigation was to determine the degree of immune reactivity to various gum antigens in the sera of individuals representing the general population. The study was a randomized, controlled trial. 288 sera purchased from a commercial source. The sera was screened for immunoglobulin G (IgG) and immunoglobulin E (IgE) antibodies against extracts of mastic gum, carrageenan, xantham gum, guar gum, gum tragacanth, locust bean gum, and β-glucan, using indirect enzyme-linked immunosorbent assay (ELISA) testing. For each gum antigen, inhibition testing was performed on the 4 sera that showed the highest IgG and IgE immune reactivity against the different gums used in the study. Inhibition testing on these same sera for sesame albumin, lentil, corn, rice, pineapple, peanut, pea protein, shrimp, or kidney bean was used to determine the cross-reactivity of these foods with the gum. Of the 288 samples, 4.2%-27% of the specimens showed a significant elevation in IgG antibodies against various gums. Only 4 of 288, or 1.4%, showed a simultaneous elevation of the IgG antibody against all 7 gum extracts. For the IgE antibody, 15.6%-29.1% of the specimens showed an elevation against the various gums. A significant percentage of the specimens, 12.8%, simultaneously produced IgE antibodies against all 7 tested extracts. Overall, the percentage of elevation in IgE antibodies against different gum extracts, with

  5. Gums, badgers, and economics

    CSIR Research Space (South Africa)

    Van Wilgen, BW

    2007-01-01

    Full Text Available Gums trees (in the genus Eucalyptus, from Australia) are not set to ‘disappear’ (even if some people wanted them to). Gums form an important component of the forest industry and, at last count, they covered over 540 000 ha in formal plantations...

  6. Controlling rheology and structure of sweet potato starch noodles with high broccoli powder content by hydrocolloids

    NARCIS (Netherlands)

    Silva, E.; Birkenhake, M.; Scholten, E.; Sagis, L.M.C.; Linden, van der E.

    2013-01-01

    Incorporating high volume fractions of broccoli powder in starch noodle dough has a major effect on its shear modulus, as a result of significant swelling of the broccoli particles. Several hydrocolloids with distinct water binding capacity (locust bean gum (LBG), guar gum, konjac glucomannan (KG),

  7. Gum Disease in Children

    Science.gov (United States)

    ... Club Program Perio Store Education & Careers Careers in Periodontics Perio Exam for Dental Licensure Recommended Competencies Periodontal ... With Find a Periodontist Gum Disease In Children Chronic gingivitis. aggressive periodontitis and generalized aggressive periodontitis are ...

  8. Xanthan - A Versatile Gum

    Indian Academy of Sciences (India)

    conveniently from microbial sources due to several factors. They can ... Why do Microorganisms Produce Gums? Most phytopathogenic bacteria do not form spores. Many of .... salts of the polymer at alkaline pH, precipitation as a quarternary.

  9. Gum Graft Surgery

    Science.gov (United States)

    ... Tomography (CBCT) American Academy of Periodontology Installs New President, Officers in Boston American Academy of Periodontology Announces ... May Increase Lung Cancer Risk CDC Estimate: New Mexico, Hawaii Have Highest U.S. Incidence of Advanced Gum ...

  10. Gum Disease and Women

    Science.gov (United States)

    ... Tomography (CBCT) American Academy of Periodontology Installs New President, Officers in Boston American Academy of Periodontology Announces ... May Increase Lung Cancer Risk CDC Estimate: New Mexico, Hawaii Have Highest U.S. Incidence of Advanced Gum ...

  11. Gum Disease Symptoms

    Science.gov (United States)

    ... Tomography (CBCT) American Academy of Periodontology Installs New President, Officers in Boston American Academy of Periodontology Announces ... May Increase Lung Cancer Risk CDC Estimate: New Mexico, Hawaii Have Highest U.S. Incidence of Advanced Gum ...

  12. The effect of gamma irradiation on guar gum, locust bean gum, gum tragacanth and gum karaya

    International Nuclear Information System (INIS)

    King, Karen; Gray, Richard

    1993-01-01

    Changes in rheological properties, as measured by viscosity, of two galactomannans (guar gum and locust beam gum) and two acidic polysaccharides (gumtragacanth and gum karaya) were studied at a range of irradiation doses o C for 1 h was determined over a wide shear rate range. All samples showed pseudoplastic behaviour which approached Newtonian with increasing irradiation dose. Viscosities were calculated at a shear rate of 54 sec -1 to enable comparison across the samples. Both galactomannans showed a decrease in viscosity with increasing γ irradiation independent of temperature and a hypothesis is proposed that at low γ irradiation doses (<2 kGy) there is a reduction in polymer aggregation in solution, whereas at higher doses polymer hydrolysis occurs. Electron spin resonance spectroscopy data supports this hypothesis, with the detection of different free radicals at low and high irradiation doses. The viscosity of the acidic polysaccharides, gum karaya and gum tragacanth, following γ irradiation at low doses (<1 kGy) was unchanged or slightly higher when compared to the unirradiated control samples. Above 1 kGy dispersion viscosity decreased with increasing dose. For these polysaccharides chain hydrolysis seems to occur during irradiation at all doses resulting in an increase in the amount of soluble polymer and hence increased viscosity at low doses, whilst at high doses viscosity decreases due to extensive polymer hydrolysis. Similar electron spin resonance (ESR) spectra were obtained at low and high doses with a stronger signal at the higher dose. (Author)

  13. (CMC)/gum arabic

    Indian Academy of Sciences (India)

    Administrator

    material, which is widely used as food additives, washes, paste, etc. It is an anionic and ... This was ascribed to the good interaction between cassava starch and CMC ... drugs and also release the heavy metals to improve the agricultural soil.

  14. The effect of gamma irradiation on guar gum, locust bean gum, gum tragacanth and gum karaya

    Energy Technology Data Exchange (ETDEWEB)

    King, Karen (Department of Agriculture for Northern Ireland, Belfast (United Kingdom) Queen' s Univ., Belfast, Northern Ireland (United Kingdom)); Gray, Richard (Department of Agriculture for Northern Ireland, Belfast (United Kingdom))

    1993-02-01

    Changes in rheological properties, as measured by viscosity, of two galactomannans (guar gum and locust beam gum) and two acidic polysaccharides (gumtragacanth and gum karaya) were studied at a range of irradiation doses < 10 kGy. Powdered samples were irradiated, and the viscosity of a 1% dispersion prepared at room temperature or by heating to 80[sup o]C for 1 h was determined over a wide shear rate range. All samples showed pseudoplastic behaviour which approached Newtonian with increasing irradiation dose. Viscosities were calculated at a shear rate of 54 sec[sup -1] to enable comparison across the samples. Both galactomannans showed a decrease in viscosity with increasing [gamma] irradiation independent of temperature and a hypothesis is proposed that at low [gamma] irradiation doses (<2 kGy) there is a reduction in polymer aggregation in solution, whereas at higher doses polymer hydrolysis occurs. Electron spin resonance spectroscopy data supports this hypothesis, with the detection of different free radicals at low and high irradiation doses. The viscosity of the acidic polysaccharides, gum karaya and gum tragacanth, following [gamma] irradiation at low doses (<1 kGy) was unchanged or slightly higher when compared to the unirradiated control samples. Above 1 kGy dispersion viscosity decreased with increasing dose. For these polysaccharides chain hydrolysis seems to occur during irradiation at all doses resulting in an increase in the amount of soluble polymer and hence increased viscosity at low doses, whilst at high doses viscosity decreases due to extensive polymer hydrolysis. Similar electron spin resonance (ESR) spectra were obtained at low and high doses with a stronger signal at the higher dose. (Author).

  15. Fluoroacetic acid in guar gum.

    Science.gov (United States)

    Vartiainen, T; Gynther, J

    1984-04-01

    The toxicity of guar gum, derived from the Indian leguminous plant Cyamopsis tetragonolobus, is thought to be due to a globulin which can be denaturated and made non-toxic. Another very toxic compound, fluoroacetic acid, has been detected at a low level in raw samples of guar gum (0.07-1.42 micrograms fluoroacetic acid/g). A sample of a guar-gum pharmaceutical formulation contained only 0.08 ppm fluoroacetate. One exceptionally high value of 9.5 micrograms/g was found in a guar-gum powder. The low concentrations of fluoroacetate found in guar gum dispel any considerations about possible health risks associated with fluoroacetate during the prolonged use of guar gum at the recommended doses.

  16. Hyperphosphorylation of cereal starch

    DEFF Research Database (Denmark)

    Carciofi, Massimiliano; Shaik, Shahnoor Sultana; Jensen, Susanne Langgård

    2011-01-01

    Plant starch is naturally phosphorylated at a fraction of the C6 and the C3 hydroxyl groups during its biosynthesis in plastids. Starch phosphate esters are important in starch metabolism and they also generate specific industrial functionality. Cereal grains starch contains little starch bound...... phosphate compared with potato tuber starch and in order to investigate the effect of increased endosperm starch phosphate, the potato starch phosphorylating enzyme glucan water dikinase (StGWD) was overexpressed specifically in the developing barley endosperm. StGWD overexpressors showed wild......-type phenotype. Transgenic cereal grains synthesized starch with higher starch bound phosphate content (7.5 (±0.67) nmol/mg) compared to control lines (0.8 (±0.05) nmol/mg) with starch granules showing altered morphology and lower melting enthalpy. Our data indicate specific action of GWD during starch...

  17. 21 CFR 201.319 - Water-soluble gums, hydrophilic gums, and hydrophilic mucilloids (including, but not limited to...

    Science.gov (United States)

    2010-04-01

    ... gum, kelp, methylcellulose, plantago seed (psyllium), polycarbophil tragacanth, and xanthan gum) as... gum, kelp, methylcellulose, plantago seed (psyllium), polycarbophil tragacanth, and xanthan gum) as..., methylcellulose, plantago seed (psyllium), polycarbophil, tragacanth, and xanthan gum. Esophageal obstruction and...

  18. Aroma interactions with starch

    DEFF Research Database (Denmark)

    Jørgensen, Anders Dysted

    Starches are used to enhance aroma perception in low-fat foods. Aroma compounds can bind physically to the starch in grooves on the surface or they can form complexes inside amylose helices. This study has been divided into two parts: one part regarding binding of aromas to starches and their aroma......-release, and another part regarding stimulation of a fungal secretome using different carbohydrates. In the first part, nine aromas and one aroma-mixture were mixed with nine different starches, including genetically modified starches. The objective of this sub-project was to bind aromas to the starches to 15 weight......-percent. Aroma binding was tested on both amorphous starches and on native starch granules. A series of aldehydes and alcohols were also tested for binding to the starches. The aromas with the highest volatility were positively retained by starch, whereas for aromas with a lower volatility the starch had...

  19. In vitro studies on guar gum based formulation for the colon targeted delivery of Sennosides.

    Science.gov (United States)

    Momin, Munira; Pundarikakshudu, K

    2004-09-24

    The objective of the present study is to develop colon targeted drug delivery systems for sennosides using guar gum as a carrier. Matrix tablets containing various proportions of guar gum were prepared by wet granulation technique using starch paste as a binder. The tablets were evaluated for content uniformity and in vitro drug release study as per BP method. T(50) % value from the dissolution studies was taken for selecting the best formulation. Guar gum matrix tablets released 4-18% sennosides in the physiological environment of gastrointestinal tract depending on the proportion of the guar gum used in the formulation. The matrix tablets containing 50% of guar gum were found to be suitable for targeting of sennosides for local action in the colon. Compared to tablets having 30% and 40% of guar gum, those with 50% guar gum gave better T(50)% (11.7 h) le and fewer amounts (5-8%) of drug release in upper GIT. These tablets with 50% guar gum released 43% and 96% sennosides with and without rat caecal fluids. This suggests the susceptibility of matrix to the colonic micro flora. The similarity factor (f2 value) for drug release with and without rat caecal fluids was found to be less than 30. When hydroxy propyl methylcellulose phthalate (10%) was used as a coat material on the matrix tablets, the initial loss of 5-8% sennosides in stomach could be completely averted. These tablets showed no change in physical appearance, content and dissolution profile upon storage at 45 degrees C / 75% relative humidity for 3 months. The results of our study indicates that matrix tablets containing 50% guar gum and coated with 10% hydroxy propyl methylcellulose phthalate are most suitable for drugs like sennosides which are mainly active in the lower GIT.

  20. Digestion of starch in a dynamic small intestinal model.

    Science.gov (United States)

    Jaime-Fonseca, M R; Gouseti, O; Fryer, P J; Wickham, M S J; Bakalis, S

    2016-12-01

    The rate and extent of starch digestion have been linked with important health aspects, such as control of obesity and type-2 diabetes. In vitro techniques are often used to study digestion and simulated nutrient absorption; however, the effect of gut motility is often disregarded. The present work aims at studying fundamentals of starch digestion, e.g. the effect of viscosity on digestibility, taking into account both biochemical and engineering (gut motility) parameters. New small intestinal model (SIM) that realistically mimics gut motility (segmentation) was used to study digestibility and simulated oligosaccharide bio accessibility of (a) model starch solutions; (b) bread formulations. First, the model was compared with the rigorously mixed stirred tank reactor (STR). Then the effects of enzyme concentration/flow rate, starch concentration, and digesta viscosity (addition of guar gum) were evaluated. Compared to the STR, the SIM showed presence of lag phase when no digestive processes could be detected. The effects of enzyme concentration and flow rate appeared to be marginal in the region of mass transfer limited reactions. Addition of guar gum reduced simulated glucose absorption by up to 45 % in model starch solutions and by 35 % in bread formulations, indicating the importance of chyme rheology on nutrient bioaccessibility. Overall, the work highlights the significance of gut motility in digestive processes and offers a powerful tool in nutritional studies that, additionally to biochemical, considers engineering aspects of digestion. The potential to modulate food digestibility and nutrient bioaccessibility by altering food formulation is indicated.

  1. Exudate gums: occurrence, production, and applications.

    Science.gov (United States)

    Verbeken, D; Dierckx, S; Dewettinck, K

    2003-11-01

    This paper presents a review of the industrially most relevant exudate gums: gum arabic, gum karya, and gum tragacanth. Exudate gums are obtained as the natural exudates of different tree species and exhibit unique properties in a wide variety of applications. This review covers the chemical structure, occurrence and production of the different gums. It also deals with the size and relative importance of the various players on the world market. Furthermore, it gives an overview of the main application fields of the different gums, both food and non-food.

  2. Nanodisturbances in deformed Gum Metal

    International Nuclear Information System (INIS)

    Gutkin, Mikhail Yu.; Ishizaki, Toshitaka; Kuramoto, Shigeru; Ovid'ko, Ilya A.

    2006-01-01

    Systematic experiments have been performed to characterize defect structures in deformed Gum Metal, a special titanium alloy with high strength, low Young's modulus, excellent cold workability and low resistance to shear in certain crystallographic planes. Results from high-resolution transmission electron microscopy characterization reveal nanodisturbances (planar nanoscopic areas of local shear) as typical elements of defect structures in deformed Gum Metal. A theoretical model is suggested describing nanodisturbances as nanoscale dipoles of non-conventional partial dislocations with arbitrary, non-quantized Burgers vectors. It is shown theoretically that the homogeneous generation of nanodisturbances is energetically favorable in Gum Metal, where they effectively carry plastic flow

  3. Assessment of Nutrient Contents of Modified Finger Millet (Eleusine coracana Starch

    Directory of Open Access Journals (Sweden)

    Tukura Bitrus Wokhe

    2017-02-01

    Full Text Available Modification processes can change the physicochemical and structural properties of native starch, thereby increasing its industrial applications. Finger millet starch (FMS was modified with casava starch (CS, guar gum (GG and xanthan gum (XG modifiers at the ratios of 95:5%, 90:10%, 80:20% and 75: 25%, for each of the modifier. The proximate and mineral compositions of the modified starch were determined using standard methods. Atomic absorption spectrometry method was used to quantify the mineral contents of the modified starch. Proximate contents of the modified FMS starch varied according to the type of the modifier and FMS/modifier ratios. Concentrations of carbohydrate in CS (66.97±0.03%, GG (64.42±0.05% and XG (64.64 ± 0.01% FMS modified starches were highest at 10%, 25% and 5% of the modifier contents repectively. The highest levels of fat in GG (8.91±0.02%, XG (7.89±0.01 and ash (3.55±0.02% in CS modified starches were recorded when the quantity of the modifiers were increased to 25%. Fatty acid levels in the modified starches varied in the order of XG (7.74±0.03% at 20% > GG (7.13±0.02% at 25% > CS (5.14±0.20% at 10%. At 25% modifier contents, levels of mineral element were highest in the modified CS and GG starches. Modifications decreased Mg, Mn, Fe, Zn, and Cu contents, while the concentrations Na, K, Ca and P increased. The modified starches can be used for production of some foods for specific health purposes.

  4. Starch degradation by irradiation

    International Nuclear Information System (INIS)

    Pruzinec, J.; Hola, O.

    1987-01-01

    The effect of high energy irradiation on various starch samples was studied. The radiation dose varied between 43 and 200.9 kGy. The viscosity of starch samples were determined by Hoeppler's method. The percentual solubility of the matter in dry starch was evaluated. The viscosity and solubility values are presented. (author) 14 refs

  5. Thermomechanical treatment of starch

    NARCIS (Netherlands)

    Goot, van der A.J.; Einde, van den R.M.

    2006-01-01

    Starch is used as a major component in many food and nonfood applications and determines the overall product properties to a large extent. It is therefore important to understand the effect of processing on starch. Many starch-based products are produced using a thermal as well as a mechanical

  6. Herbal-caffeinated chewing gum, but not bubble gum, improves aspects of memory.

    Science.gov (United States)

    Davidson, Matthew G

    2011-08-01

    Research has shown that standard chewing gum can affect aspects of both attention and memory. The present study examined the effects of Think Gum®, a caffeinated-herbal chewing gum, on both concentration and memory using a series of paper-based and online testing. Compared to standard chewing gum and a no-gum control, chewing caffeinated-herbal gum during testing improved aspects of memory, but did not affect concentration. The findings suggest that caffeinated-herbal chewing gum is an effective memory aid. Copyright © 2011 Elsevier Ltd. All rights reserved.

  7. Synthesis of oxidized guar gum by dry method and its application in reactive dye printing.

    Science.gov (United States)

    Gong, Honghong; Liu, Mingzhu; Zhang, Bing; Cui, Dapeng; Gao, Chunmei; Ni, Boli; Chen, Jiucun

    2011-12-01

    The aim of this study was to prepare oxidized guar gum with a simple dry method, basing on guar gum, hydrogen peroxide and a small amount of solvent. To obtain a product with suitable viscosity for reactive dye printing, the effects of various factors such as the amount of oxidant and solvent, reaction temperature and time were studied with respect to the viscosity of reaction products. The product was characterized by Fourier transform infrared spectroscopy, size exclusion chromatography, scanning electron microscopy and differential scanning calorimetry. The hydrated rate of guar gum and oxidized guar gum was estimated through measuring the required time when their solutions (1%, w/v) reached the maximum viscosity. The effects of the salt concentration and pH on viscosity of the resultant product were studied. The mixed paste containing oxidized guar gum and carboxymethyl starch was prepared and its viscosity was determined by the viscometer. The rheological property of the mixed paste was appraised by the printing viscosity index. In addition, the applied effect of mixed paste in reactive dye printing was examined by assessing the fabric stiffness, color yield and sharp edge to the printed image in comparison with sodium alginate. And the results indicated that the mixed paste could partially replace sodium alginate as thickener in reactive dye printing. The study also showed that the method was low cost and eco-friendly and the product would have an extensive application in reactive dye printing. Copyright © 2011 Elsevier B.V. All rights reserved.

  8. Oral health benefits of chewing gum

    NARCIS (Netherlands)

    Wessel, Stefan

    2016-01-01

    In the last decades sugar-free chewing gum has developed in an oral healthcare product, next to the conventional products such as the toothbrush and mouthrinses. In this thesis we investigate the oral health benefits of chewing gum and the effects of additives to chewing gum, such as antimicrobials.

  9. 21 CFR 184.1351 - Gum tragacanth.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Gum tragacanth. 184.1351 Section 184.1351 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN... Substances Affirmed as GRAS § 184.1351 Gum tragacanth. (a) Gum tragacanth is the exudate from one of several...

  10. Elastic properties of Gum Metal

    International Nuclear Information System (INIS)

    Kuramoto, Shigeru; Furuta, Tadahiko; Hwang, Junghwan; Nishino, Kazuaki; Saito, Takashi

    2006-01-01

    In situ X-ray diffraction measurements under tensile loading and dynamic mechanical analysis were performed to investigate the mechanisms of elastic deformation in Gum Metal. Tensile stress-strain curves for Gum Metal indicate that cold working substantially decreases the elastic modulus while increasing the yield strength, thereby confirming nonlinearity in the elastic range. The gradient of each curve decreased continuously to about one-third its original value near the elastic limit. As a result of this decrease in elastic modulus and nonlinearity, elastic deformability reaches 2.5% after cold working. Superelasticity is attributed to stress-induced martensitic transformations, although the large elastic deformation in Gum Metal is not accompanied by a phase transformation

  11. Thermoplastic starch materials prepared from rice starch

    International Nuclear Information System (INIS)

    Pontes, Barbara R.B.; Curvelo, Antonio A.S.

    2009-01-01

    Rice starch is a source still little studied for the preparation of thermoplastic materials. However, its characteristics, such as the presence of proteins, fats and fibers may turn into thermoplastics with a better performance. The present study intends the evaluation of the viability of making starch thermoplastic from rice starch and glycerol as plasticizer. The results of X-ray diffraction and scanning electronic microscopy demonstrate the thermoplastic acquisition. The increase of plasticizer content brings on more hydrophilic thermoplastics with less resistance to tension and elongation at break. (author)

  12. The CT appearance of intraoral chewing gum

    International Nuclear Information System (INIS)

    Towbin, Alexander J.

    2008-01-01

    When imaged, intraoral chewing gum has the potential to be misdiagnosed. Chewing gum has a characteristic appearance on CT: it is ovoid in shape, hyperdense, and has small internal locules of air. Reports have described the appearance of gum on radiographs and abdominal CT images; however, no reports could be found detailing its appearance within the mouth. This report describes the appearance of intraoral chewing gum as well as the properties of the gum that lead to this appearance. Because of the potential for misdiagnosis, screening for intraoral foreign bodies should be considered prior to imaging. (orig.)

  13. The CT appearance of intraoral chewing gum

    Energy Technology Data Exchange (ETDEWEB)

    Towbin, Alexander J. [Cincinnati Children' s Hospital Medical Center, Department of Radiology, Cincinnati, OH (United States)

    2008-12-15

    When imaged, intraoral chewing gum has the potential to be misdiagnosed. Chewing gum has a characteristic appearance on CT: it is ovoid in shape, hyperdense, and has small internal locules of air. Reports have described the appearance of gum on radiographs and abdominal CT images; however, no reports could be found detailing its appearance within the mouth. This report describes the appearance of intraoral chewing gum as well as the properties of the gum that lead to this appearance. Because of the potential for misdiagnosis, screening for intraoral foreign bodies should be considered prior to imaging. (orig.)

  14. GumTree: Data reduction

    Energy Technology Data Exchange (ETDEWEB)

    Rayner, Hugh [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)]. E-mail: hrz@ansto.gov.au; Hathaway, Paul [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia); Hauser, Nick [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia); Fei, Yang [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia); Franceschini, Ferdi [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia); Lam, Tony [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, NSW (Australia)

    2006-11-15

    Access to software tools for interactive data reduction, visualisation and analysis during a neutron scattering experiment enables instrument users to make informed decisions regarding the direction and success of their experiment. ANSTO aims to enhance the experiment experience of its facility's users by integrating these data reduction tools with the instrument control interface for immediate feedback. GumTree is a software framework and application designed to support an Integrated Scientific Experimental Environment, for concurrent access to instrument control, data acquisition, visualisation and analysis software. The Data Reduction and Analysis (DRA) module is a component of the GumTree framework that allows users to perform data reduction, correction and basic analysis within GumTree while an experiment is running. It is highly integrated with GumTree, able to pull experiment data and metadata directly from the instrument control and data acquisition components. The DRA itself uses components common to all instruments at the facility, providing a consistent interface. It features familiar ISAW-based 1D and 2D plotting, an OpenGL-based 3D plotter and peak fitting performed by fityk. This paper covers the benefits of integration, the flexibility of the DRA module, ease of use for the interface and audit trail generation.

  15. GumTree: Data reduction

    International Nuclear Information System (INIS)

    Rayner, Hugh; Hathaway, Paul; Hauser, Nick; Fei, Yang; Franceschini, Ferdi; Lam, Tony

    2006-01-01

    Access to software tools for interactive data reduction, visualisation and analysis during a neutron scattering experiment enables instrument users to make informed decisions regarding the direction and success of their experiment. ANSTO aims to enhance the experiment experience of its facility's users by integrating these data reduction tools with the instrument control interface for immediate feedback. GumTree is a software framework and application designed to support an Integrated Scientific Experimental Environment, for concurrent access to instrument control, data acquisition, visualisation and analysis software. The Data Reduction and Analysis (DRA) module is a component of the GumTree framework that allows users to perform data reduction, correction and basic analysis within GumTree while an experiment is running. It is highly integrated with GumTree, able to pull experiment data and metadata directly from the instrument control and data acquisition components. The DRA itself uses components common to all instruments at the facility, providing a consistent interface. It features familiar ISAW-based 1D and 2D plotting, an OpenGL-based 3D plotter and peak fitting performed by fityk. This paper covers the benefits of integration, the flexibility of the DRA module, ease of use for the interface and audit trail generation

  16. PEG and Thickeners: A Critical Interaction Between Polyethylene Glycol Laxative and Starch-Based Thickeners.

    Science.gov (United States)

    Carlisle, Brian J; Craft, Garrett; Harmon, Julie P; Ilkevitch, Alina; Nicoghosian, Jenik; Sheyner, Inna; Stewart, Jonathan T

    2016-09-01

    Clinicians commonly encounter dysphagia and constipation in a skilled nursing population. Increasing the viscosity of liquids, usually with a starch- or xanthan gum-based thickener, serves as a key intervention for patients with dysphagia. We report a newly identified and potentially dangerous interaction between polyethylene glycol 3350 laxative (PEG) and starch-thickened liquids. A patient requiring nectar-thickened liquids became constipated, and medical staff prescribed PEG for constipation. His nurse observed that the thickened apple juice immediately thinned to near-water consistency when PEG was added. She obtained the same results with thickened water and coffee. We quantified this phenomenon by isothermal rotational rheology. Results confirmed a precipitous loss of thickening when PEG was added to starch-based thickeners but not with xanthan gum-based thickeners. Clinicians and front-line staff should be aware of this potentially critical interaction between PEG- and starch-based thickeners. Although confirmatory studies are needed, our preliminary data suggest that PEG may be compatible with xanthan gum-- based thickeners. Copyright © 2016 AMDA – The Society for Post-Acute and Long-Term Care Medicine. All rights reserved.

  17. Chewing gum can produce context-dependent effects upon memory.

    Science.gov (United States)

    Baker, Jess R; Bezance, Jessica B; Zellaby, Ella; Aggleton, John P

    2004-10-01

    Two experiments examined whether chewing spearmint gum can affect the initial learning or subsequent recall of a word list. Comparing those participants in Experiment 1 who chewed gum at the learning or the recall phases showed that chewing gum at initial learning was associated with superior recall. In addition, chewing gum led to context-dependent effects as a switch between gum and no gum (or no gum and gum) between learning and recall led to poorer performance. Experiment 2 provided evidence that sucking gum was sufficient to induce some of the same effects as chewing.

  18. THERMAL ANALYSIS, RHEOLOGY, X-RAY DIFFRACTOMETRY AND ATOMIC FORCE MICROSCOPY IN THE EVALUATION OF BINARY MIXTURES OF “STARCH-HYDROCOLLOIDS”

    Directory of Open Access Journals (Sweden)

    Crislaine Alberton

    2014-02-01

    Full Text Available Starch is arguably the most investigated biopolymer in the world and the cassava starch that is extracted from Manihot esculenta Crantz, represents an important vegetal crop in tropical countries, where its roots and derivatives serve as food and a source of energy. The main composition of these roots is 70-80% water, 16-24% starch and small quantities (<4% of protein, lipids vitamins and minerals. Hydrocolloids, or gums, are substances consisting of a hydrophilic long-chain with colloidal properties that, in water-based systems, produce gels. Starches and hydrocolloids are often used together in food systems to provide texture, water mobility, control moisture, improve product quality and stability, facilitate processing and reduce costs. In this study, the interactions between cassava and starch-hydrocolloids (1% of the following gums: CMC, jatahy, pectin and xanthan were investigated. The TG/DTG method made it possible to determine the thermal decomposition of each sample, which under air atmosphere occurs in three steps. Little difference was observed in the degree of relative crystallinity (XRD and in the average roughness or average diameter of the starch granules (NC-AFM. The viscosity and pasting properties (RVA increased, and were higher for starch treated with jatahy gum. A large decrease was observed in peak temperature and gelatinisation enthalpy for the treated samples (DSC.

  19. 21 CFR 172.615 - Chewing gum base.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Chewing gum base. 172.615 Section 172.615 Food and..., Chewing Gum Bases and Related Substances § 172.615 Chewing gum base. The food additive chewing gum base... substances listed in paragraph (a) of this section, chewing gum base may also include substances generally...

  20. Structure of the arabinogalactan from gum tragacanth (Astralagus gummifer).

    Science.gov (United States)

    Tischer, Cesar A; Iacomini, Marcello; Gorin, Philip A J

    2002-10-08

    The polysaccharide obtained by ethanol precipitation from an aqueous solution of gum tragacanth contained arabinogalactan and tragacanthic acid, as well as starch ( approximately 0.6%). GC-MS, NMR, and ESI-MS analyses showed the structure of the arabinogalactan to be even more complex than previously determined, with core structures containing Arap, beta-Araf, and alpha-Galp units, as well as known terminal, and 2-O- and 3-O-substituted alpha-Araf units. Analysis was aided by examination of free, reducing oligosaccharides present in the gum. In addition to maltose, maltotriose, maltotetraose, and maltopentaose, the following were characterized: mixed alpha-Araf (1-->2)-alpha-Araf-(1-->4)-Ara and alpha-Araf-(1-->2)-alpha-Araf-(1-->5)-Ara, which correspond to the side chains of the arabinogalactan, beta-Galp-(1-->4)-beta-Galp-(1-->4)-beta-Galp-(1-->4)-Gal; and a mixture of beta-Galp-(1-->4)-beta-Galp-(1-->4)-Gal and beta-Glcp-(1-->4)-beta-Galp-(1-->4)-beta-Galp-(1-->4)-Gal, which did not resemble side-chain structures of the arabinogalactan. The latter are suggested to be related to tragacanthic acid, which has been previously found to contain beta-Galp nonreducing end-units.

  1. Potato starch synthases

    NARCIS (Netherlands)

    Nazarian-Firouzabadi, Farhad; Visser, Richard G.F.

    2017-01-01

    Starch, a very compact form of glucose units, is the most abundant form of storage polyglucan in nature. The starch synthesis pathway is among the central biochemical pathways, however, our understanding of this important pathway regarding genetic elements controlling this pathway, is still

  2. Occupational asthma caused by guar gum.

    Science.gov (United States)

    Lagier, F; Cartier, A; Somer, J; Dolovich, J; Malo, J L

    1990-04-01

    Some vegetable gums have been reported to cause asthma. We describe three subjects who were exposed at work to guar gum, which is derived from the outer part of Cyanopsis tetragonolobus, a vegetable that grows in India. The first subject worked for a pharmaceutical company; the second and third subjects worked at a carpet-manufacturing plant. All three subjects developed symptoms of rhinitis and asthma after the onset of exposure to guar gum. All subjects were atopic and demonstrated mild bronchial hyperresponsiveness to inhaled histamine at the time they were observed. Skin prick tests demonstrated an immediate skin reaction to guar gum. All three subjects had high levels of serum IgE antibodies to guar gum. Specific inhalation challenges in which the three subjects were exposed for short intervals (less than or equal to 4 minutes) to powder of guar gum elicited isolated immediate bronchospastic reactions in two subjects and a dual reaction in the other subject.

  3. Starch Bioengineering in Barley

    DEFF Research Database (Denmark)

    Shaik, Shahnoor Sultana

    , the effects of engineering high levels of phosphate and amylose content on starch physico-chemical properties were evaluated by various biochemical and morphological studies. As a result, a substantial increase of 10-fold phosphate content and ~99% amylose content with high-resistant starch was observed...... in storage reserve accumulation, metabolite accumulation in AO but no significant differences were observed in HP compared to WT. Scanning electron microscopy and confocal microscopy revealed the details in topography and internal structures of the starch granules in these lines. The results demonstrated......Starch represents the most important carbohydrate used for food and feed purposes. Increasingly, it is also used as a renewable raw material, as a source of biofuel, and for many different industrial applications. Progress in understanding starch biosynthesis, and investigations of the genes...

  4. Future cereal starch bioengineering

    DEFF Research Database (Denmark)

    Blennow, Andreas; Jensen, Susanne Langgård; Shaik, Shahnoor Sultana

    2013-01-01

    The importance of cereal starch production worldwide cannot be overrated. However, the qualities and resulting values of existing raw and processed starch do not fully meet future demands for environmentally friendly production of renewable, advanced biomaterials, functional foods, and biomedical...... additives. New approaches for starch bioengineering are needed. In this review, we discuss cereal starch from a combined universal bioresource point of view. The combination of new biotechniques and clean technology methods can be implemented to replace, for example, chemical modification. The recently...... released cereal genomes and the exploding advancement in whole genome sequencing now pave the road for identifying new genes to be exploited to generate a multitude of completely new starch functionalities directly in the cereal grain, converting cereal crops to production plants. Newly released genome...

  5. Isolation and characterization of gum from Chrysophyllum albidum ...

    African Journals Online (AJOL)

    This study describes the morphology, physicochemical and compressional characteristics of a natural gum derived from the fruits of Chrysophyllum albidum. Preliminary phytochemical screening and physicochemical properties of Chrysophyllum albidum gum (in comparison with tragacanth gum) were determined while ...

  6. Influence of Sugars, Modified Starches and Hydrocolloids Addition on Colour and Thermal Properties of Raspberry Cream Fillings

    Directory of Open Access Journals (Sweden)

    Pichler Anita

    2017-03-01

    Full Text Available This paper deals with the influence of the addition of sugars (sucrose, fructose and trehalose, modified starches (tapioca or waxy maize starch and hydrocolloids (karaya or guar gum on colour and thermal properties of raspberry cream fillings. In addition, the influence of the above-mentioned additives on the colour and thermal properties of raspberry cream fillings stored at room temperature over a period of 8 and 16 months was investigated. Results showed that the highest anthocyanin content and total phenolic content were detected in raspberry cream filling prepared with sucrose and trehalose in combination with guar gum. During storage, after 8 and 16 months at room temperature, anthocyanin content and total phenolic content decreased. Results also showed that the kind of sugar and added modified starches or hydrocolloids influenced the thermal properties of cream fillings. During storage, a decrease was observed in both freezing temperature as well as enthalpy of cream fillings.

  7. Recent trends on gellan gum blends with natural and synthetic polymers: A review.

    Science.gov (United States)

    Zia, Khalid Mahmood; Tabasum, Shazia; Khan, Muhammad Faris; Akram, Nadia; Akhter, Naheed; Noreen, Aqdas; Zuber, Mohammad

    2018-04-01

    Gellan gum (GG), a linear negatively charged exopolysaccharide,is biodegradable and non-toxic in nature. It produces hard and translucent gel in the presence of metallic ions which is stable at low pH. However, GG has poor mechanical strength, poor stability in physiological conditions, high gelling temperature and small temperature window.Therefore,it is blended with different polymers such as agar, chitosan, cellulose, sodium alginate, starch, pectin, polyanaline, pullulan, polyvinyl chloride, and xanthan gum. In this article, a comprehensive overview of combination of GG with natural and synthetic polymers/compounds and their applications in biomedical field involving drug delivery system, insulin delivery, wound healing and gene therapy, is presented. It also describes the utilization of GG based materials in food and petroleum industry. All the technical scientific issues have been addressed; highlighting the recent advancement. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Gluten-free dough-making of specialty breads: Significance of blended starches, flours and additives on dough behaviour.

    Science.gov (United States)

    Collar, Concha; Conte, Paola; Fadda, Costantino; Piga, Antonio

    2015-10-01

    The capability of different gluten-free (GF) basic formulations made of flour (rice, amaranth and chickpea) and starch (corn and cassava) blends, to make machinable and viscoelastic GF-doughs in absence/presence of single hydrocolloids (guar gum, locust bean and psyllium fibre), proteins (milk and egg white) and surfactants (neutral, anionic and vegetable oil) have been investigated. Macroscopic (high deformation) and macromolecular (small deformation) mechanical, viscometric (gelatinization, pasting, gelling) and thermal (gelatinization, melting, retrogradation) approaches were performed on the different matrices in order to (a) identify similarities and differences in GF-doughs in terms of a small number of rheological and thermal analytical parameters according to the formulations and (b) to assess single and interactive effects of basic ingredients and additives on GF-dough performance to achieve GF-flat breads. Larger values for the static and dynamic mechanical characteristics and higher viscometric profiles during both cooking and cooling corresponded to doughs formulated with guar gum and Psyllium fibre added to rice flour/starch and rice flour/corn starch/chickpea flour, while surfactant- and protein-formulated GF-doughs added to rice flour/starch/amaranth flour based GF-doughs exhibited intermediate and lower values for the mechanical parameters and poorer viscometric profiles. In addition, additive-free formulations exhibited higher values for the temperature of both gelatinization and retrogradation and lower enthalpies for the thermal transitions. Single addition of 10% of either chickpea flour or amaranth flour to rice flour/starch blends provided a large GF-dough hardening effect in presence of corn starch and an intermediate effect in presence of cassava starch (chickpea), and an intermediate reinforcement of GF-dough regardless the source of starch (amaranth). At macromolecular level, both chickpea and amaranth flours, singly added, determined

  9. Characterization of starch nanoparticles

    Science.gov (United States)

    Szymońska, J.; Targosz-Korecka, M.; Krok, F.

    2009-01-01

    Nanomaterials already attract great interest because of their potential applications in technology, food science and medicine. Biomaterials are biodegradable and quite abundant in nature, so they are favoured over synthetic polymer based materials. Starch as a nontoxic, cheap and renewable raw material is particularly suitable for preparation of nanoparticles. In the paper, the structure and some physicochemical properties of potato and cassava starch particles of the size between 50 to 100 nm, obtained by mechanical treatment of native starch, were presented. We demonstrated, with the aim of the Scanning Electron Microscopy (SEM) and the non-contact Atomic Force Microscopy (nc-AFM), that the shape and dimensions of the obtained nanoparticles both potato and cassava starch fit the blocklets - previously proposed as basic structural features of native starch granules. This observation was supported by aqueous solubility and swelling power of the particles as well as their iodine binding capacity similar to those for amylopectin-type short branched polysaccharide species. Obtained results indicated that glycosidic bonds of the branch linkage points in the granule amorphous lamellae might be broken during the applied mechanical treatment. Thus the released amylopectin clusters could escape out of the granules. The starch nanoparticles, for their properties qualitatively different from those of native starch granules, could be utilized in new applications.

  10. Structural, thermal and rheological characterization of modified Dalbergia sissoo gum--A medicinal gum.

    Science.gov (United States)

    Munir, Hira; Shahid, Muhammad; Anjum, Fozia; Mudgil, Deepak

    2016-03-01

    Dalbergia sissoo gum was purified by ethanol precipitation. The purified gum was modified and hydrolyzed. Gum was modified by performing polyacrylamide grafting and carboxymethylation methods. The hydrolysis was carried out by using mannanase, barium hydroxide and trifluoroacetic acid. The modified and hydrolyzed gums were characterized using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The decrease in viscosity was studied by performing the flow test. The modified and hydrolyzed gums were thermally stable as compared to crude gum. There was increase in crystallinity after modification and hydrolysis, determined through XRD. FTIR analysis exhibits no major transformation of functional group, only there was change in the intensity of transmittance. It is concluded that the modified and hydrolyzed gum can be used for pharmaceutical and food industry. Copyright © 2015 Elsevier B.V. All rights reserved.

  11. Gum chewing and cognition : an overview

    NARCIS (Netherlands)

    Tucha, L.I.; Koerts, J.

    In recent years, there was a debate about the effects of gum chewing on various aspects of cognitive functioning. In this review, the results of previous studies are presented and summarized. There is a clear indication that gum chewing can improve various aspects of cognitive functioning including

  12. Gum chewing affects academic performance in adolescents

    Science.gov (United States)

    Chewing gum may have an impact on improved memory during specific tasks of recognition and sustained attention. Research objective was to determine the effect of gum chewing on standardized test scores and math class grades of eighth grade students. Four math classes, 108 students, were randomized i...

  13. 21 CFR 582.7351 - Gum tragacanth.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Gum tragacanth. 582.7351 Section 582.7351 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS... tragacanth. (a) Product. Tragacanth (gum tragacanth). (b) Conditions of use. This substance is generally...

  14. Enzymatic modification of starch

    DEFF Research Database (Denmark)

    Jensen, Susanne Langgård

    In the food industry approaches for using bioengineering are investigated as alternatives to conventional chemical and physical starch modification techniques in development of starches with specific properties. Enzyme-assisted post-harvest modification is an interesting approach to this, since...... it is considered a clean and energy saving technology. This thesis aimed to investigate the effect of using reaction conditions, simulating an industrial process, for enzymatic treatment of starch with branching enzyme (BE) from Rhodothermus obamensis. Thus treatements were conducted at 70°C using very high...... substrate concentration (30-40% dry matter (DM)) and high enzyme activity (750-2250 BE units (BEU)/g sample). Starches from various botanical sources, representing a broad range of properties, were used as substrates. The effects of the used conditions on the BE-reaction were evaluated by characterization...

  15. Environmental impact assessment of six starch plastics focusing on wastewater-derived starch and additives

    NARCIS (Netherlands)

    Broeren, Martijn L.M.; Kuling, Lody; Worrell, Ernst; Shen, Li

    2017-01-01

    Starch plastics are developed for their biobased origin and potential biodegradability. To assist the development of sustainable starch plastics, this paper quantifies the environmental impacts of starch plastics produced from either virgin starch or starch reclaimed from wastewater. A

  16. Examining disadoption of gum arabic production in Sudan

    NARCIS (Netherlands)

    Rahim, A.; Ruben, R.; Ierland, van E.C.

    2008-01-01

    Gum arabic production in Sudan has developed over the years in a well-established traditional bush-fallow system in which the gum tree (Acacia senegal) is rotated with annual crops. Following the Sahel drought, the gum area has suffered from deforestation and gum production has declined. Several

  17. Brief Report: Gum Chewing Affects Standardized Math Scores in Adolescents

    Science.gov (United States)

    Johnston, Craig A.; Tyler, Chermaine; Stansberry, Sandra A.; Moreno, Jennette P.; Foreyt, John P.

    2012-01-01

    Gum chewing has been shown to improve cognitive performance in adults; however, gum chewing has not been evaluated in children. This study examined the effects of gum chewing on standardized test scores and class grades of eighth grade math students. Math classes were randomized to a gum chewing (GC) condition that provided students with gum…

  18. In vitro digestibility of banana starch cookies.

    Science.gov (United States)

    Bello-Pérez, Luis A; Sáyago-Ayerdi, Sonia G; Méndez-Montealvo, Guadalupe; Tovar, Juscelino

    2004-01-01

    Banana starch was isolated and used for preparation of two types of cookies. Chemical composition and digestibility tests were carried out on banana starch and the food products, and these results were compared with corn starch. Ash, protein, and fat levels in banana starch were higher than in corn starch. The high ash amount in banana starch could be due to the potassium content present in this fruit. Proximal analysis was similar between products prepared with banana starch and those based on corn starch. The available starch content of the banana starch preparation was 60% (dmb). The cookies had lower available starch than the starches while banana starch had lower susceptibility to the in vitro alpha-amylolysis reaction. Banana starch and its products had higher resistant starch levels than those made with corn starch.

  19. Occupational allergic rhinitis from guar gum.

    Science.gov (United States)

    Kanerva, L; Tupasela, O; Jolanki, R; Vaheri, E; Estlander, T; Keskinen, H

    1988-05-01

    Three cases of allergic rhinitis from a vegetable gum, guar gum, have been detected. Two subjects were exposed to fine guar gum powder (Emco Gum 563, Meyhall Chemical AG, Switzerland), an insulator in rubber cables, when opening cables in a power cable laboratory. After 1-2 years' exposure the patients developed rhinitis. Scratch-chamber tests, nasal provocation tests, nasal eosinophilia and a RAST test proved their allergy. A third subject developed allergic rhinitis from another guar gum product (Meyproid 5306, Meyhall Chemical AG) after 2 years' exposure in a paper factory. A positive skin test and nasal provocation test confirmed the diagnosis. A fourth case of possible allergy to guar gum after exposure to Meyproid 5306 in a paper factory is also presented. No final diagnosis was reached in this case (in 1974). The present subjects, only one of whom was atopic, developed allergy within 2 years, although their exposure to guar gum was not especially heavy. Therefore, when handling guar, adequate ventilation facilities should be provided and protective clothing, including a respiratory mask, should be worn.

  20. Chewing gum moderates the vigilance decrement.

    Science.gov (United States)

    Morgan, Kate; Johnson, Andrew J; Miles, Christopher

    2014-05-01

    We examine the impact of chewing gum on a Bakan-type vigilance task that requires the continual updating of short-term order memory. Forty participants completed a 30-min auditory Bakan-task either with, or without, the requirement to chew gum. Self-rated measures of mood were taken both pre- and post-task. As expected, the vigilance task produced a time-dependent performance decrement indexed via decreases in target detections and lengthened correct reaction times (RTs), and a reduction in post-task self-rated alertness scores. The declines in both performance and subjective alertness were attenuated in the chewing-gum group. In particular, correct RTs were significantly shorter following the chewing of gum in the latter stages of the task. Additionally, the gradients of decline for target detection and incline for correct RTs were both attenuated for the chewing-gum group. These findings are consistent with the data of Tucha and Simpson (2011), Appetite, 56, 299-301, who showed beneficial effects of chewing gum in the latter stages of a 30 min visual attention task, and extend their data to a task that necessitates the continuous updating of order memory. It is noteworthy that our data contradict the claim (Kozlov, Hughes, & Jones, 2012, Q. J. Exp. Psychology, 65, 501-513) that chewing gum negatively impacts short-term memory task performance. © 2013 The British Psychological Society.

  1. Chewing gum and context-dependent memory: the independent roles of chewing gum and mint flavour.

    Science.gov (United States)

    Johnson, Andrew J; Miles, Christopher

    2008-05-01

    Two experiments independently investigated the basis of the chewing gum induced context-dependent memory effect. At learning and/or recall, participants either chewed flavourless gum (Experiment 1) or received mint-flavoured strips (Experiment 2). No context-dependent memory effect was found with either flavourless gum or mint-flavoured strips, indicating that independently the contexts were insufficiently salient to induce the effect. This is found despite participants' subjective ratings indicating a perceived change in state following administration of flavourless gum or mint-flavoured strips. Additionally, some preliminary evidence for a non-additive facilitative effect of receiving gum or flavour at either learning and/or recall is reported. The findings raise further concerns regarding the robustness of the previously reported context-dependent memory effect with chewing gum.

  2. Starch phosphorylation plays an important role in starch biosynthesis

    NARCIS (Netherlands)

    Xu, Xuan; Dees, Dianka; Dechesne, Annemarie; Huang, Xing Feng; Visser, Richard G.F.; Trindade, Luisa M.

    2017-01-01

    Starch phosphate esters are crucial in starch metabolism and render valuable functionality to starches for various industrial applications. A potato glucan, water dikinase (GWD1) was introduced in tubers of two different potato genetic backgrounds: an amylose-containing line Kardal and the

  3. Chewing gum and context-dependent memory: The independent roles of chewing gum and mint flavour

    OpenAIRE

    Johnson, A.J.; Miles, C.

    2008-01-01

    Two experiments independently investigated the basis of the chewing-gum induced context-dependent memory effect (Baker et al, 2004). At learning and/or recall participants either chewed flavourless gum (Experiment 1) or received mint-flavoured strips (Experiment 2). No context dependent memory effect was found with either flavourless gum or mint-flavoured strips, indicating that independently the contexts were insufficiently salient to induce the effect. This is found despite participants’ su...

  4. Gummed-up memory: Chewing gum impairs short-term recall

    OpenAIRE

    Kozlov, Michail D; Hughes, Robert W; Jones, Dylan M

    2012-01-01

    Several studies have suggested that short-term memory is generally improved by chewing gum. However, we report the first studies to show that chewing gum impairs short-term memory for both item order and item identity. Experiment 1 showed that chewing gum reduces serial recall of letter lists. Experiment 2 indicated that chewing does not simply disrupt vocal-articulatory planning required for order retention: Chewing equally impairs a matched task that required retention of list item identity...

  5. Extraction and Characterization of Boswellia Serrata Gum as Pharmaceutical Excipient.

    Science.gov (United States)

    Panta, Sumedha; Malviya, Rishabha; Sharma, Pramod

    2015-01-01

    This manuscript deals with the purification and characterization of Boswellia serrata gum as a suspending agent. The Boswellia serrata gum was purchased as crude material, purified and further characterized in terms of organoleptic properties and further micromeritic studies were carried out to characterize the polymer as a pharmaceutical excipient. The suspending properties of the polymer were also evaluated. The results showed that the extracted gum possesses optimum organoleptic as well as micromeritic and suspending properties. To characterize Boswellia serrata gum as a natural excipient. Boswellia serrata gum, paracetamol, distilled water. The results showed that the extracted gum possesses optimum organoleptic as well as micromeritic and suspending properties. It is concluded from the research work that the gum extracted from Boswellia serrata shows the presence of carbohydrates after chemical tests. All the organoleptic properties evaluated were found to be acceptable. The pH was found to be slightly acidic. Swelling Index reveals that the gum swells well in water. Total ash value was within the limits. The values of angle of repose and Carr's Index of powdered gum powder showed that the flow property was good. IR spectra confirmed the presence of alcohol, amines, ketones, anhydrides and aromatic rings. The suspending properties of Boswellia serrata gum were found to be higher as compared to gum acacia while the flow rate of Boswellia serrata gum (1% suspension) was less than gum acacia (1% suspension). The viscosity measurement of both Boswellia serrata gum suspension and gum acacia suspension showed approximately similar results.

  6. Design, formulation and evaluation of caffeine chewing gum.

    Science.gov (United States)

    Aslani, Abolfazl; Jalilian, Fatemeh

    2013-01-01

    Caffeine which exists in drinks such as coffee as well as in drug dosage forms in the global market is among the materials that increase alertness and decrease fatigue. Compared to other forms of caffeine, caffeine gum can create faster and more prominent effects. In this study, the main goal is to design a new formulation of caffeine gum with desirable taste and assess its physicochemical properties. Caffeine gum was prepared by softening of gum bases and then mixing with other formulation ingredients. To decrease the bitterness of caffeine, sugar, aspartame, liquid glucose, sorbitol, manitol, xylitol, and various flavors were used. Caffeine release from gum base was investigated by mechanical chewing set. Content uniformity test was also performed on the gums. The gums were evaluated in terms of organoleptic properties by the Latin-Square design at different stages. After making 22 formulations of caffeine gums, F11 from 20 mg caffeine gums and F22 from 50 mg caffeine gums were chosen as the best formulation in organoleptic properties. Both types of gum released about 90% of their own drug content after 30 min. Drug content of 20 and 50 mg caffeine gum was about 18.2-21.3 mg and 45.7-53.6 mg respectively. In this study, 20 and 50 mg caffeine gums with suitable and desirable properties (i.e., good taste and satisfactory release) were formulated. The best flavor for caffeine gum was cinnamon. Both kinds of 20 and 50 mg gums succeeded in content uniformity test.

  7. Radiation processing of starch

    International Nuclear Information System (INIS)

    Kamaruddin Hashim

    2008-01-01

    Starch is a polysaccharide material and generally, it is non-toxic, biocompatible and biodegradable. It mainly use as foodstuff, food additives, production of sugar and flavouring. Sago palm with scientific name Genus Metroxylon belonging to family Palmae is an important resource in the production of sago starch in Malaysia. Nearly 90% of sago planting areas is found in Sarawak State of Malaysia. It can easily grow under the harsh swampy environment. The sago starch content 4% polyphenol, which is an active compound with antioxidant property that has potential benefit in health and skin care applications. Renewal resources and environmental friendly of natural polymer reason for the researcher to explore the potential of this material in order to improve our quality of live. (author)

  8. Structure of potato starch

    DEFF Research Database (Denmark)

    Bertoft, Eric; Blennow, Andreas

    2016-01-01

    Potato starch granules consist primarily of two tightly packed polysaccharides, amylose and amylopectin. Amylose, which amount for 20-30%, is the principal linear component, but a fraction is in fact slightly branched. Amylopectin is typically the major component and is extensively branched...... chains extending from the clusters. A range of enzymes is involved in the biosynthesis of the cluster structures and linear segments. These are required for sugar activation, chain elongation, branching, and trimming of the final branching pattern. As an interesting feature, potato amylopectin...... is substituted with low amounts of phosphate groups monoesterified to the C-3 and the C-6 carbons of the glucose units. They seem to align well in the granular structure and have tremendous effects on starch degradation in the potato and functionality of the refined starch. A specific dikinase catalyzes...

  9. Effect of partially hydrolyzed guar gum on pasting, thermo-mechanical and rheological properties of wheat dough.

    Science.gov (United States)

    Mudgil, Deepak; Barak, Sheweta; Khatkar, B S

    2016-12-01

    Partially hydrolyzed guar gum was prepared using enzymatic hydrolysis of native guar gum that can be utilized as soluble fiber source. The effect of partially hydrolyzed guar gum (PHGG) on pasting, thermo-mechanical and rheological properties of wheat flour was investigated using rapid visco-analyzer, Mixolab and Microdoughlab. Wheat flour was replaced with 1-5g PHGG per 100g of wheat flour on weight basis. PHGG addition decreased the peak, trough, breakdown, setback and final viscosity of wheat flour. Water absorption and amylase activity of wheat dough were increased whereas starch gelatinization and protein weakening of wheat dough were reduced as a result of PHGG addition to wheat flour. PHGG addition also increased the peak dough height, arrival time, dough development time, dough stability and peak energy of wheat dough system. However, dough softening was decreased after PHGG addition to wheat flour dough. Overall, it can be assumed that PHGG has influenced the properties of wheat flour dough system by decreasing the RVA viscosities and increasing the water absorption and starch gelatinization of wheat dough system. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Diabetes, Gum Disease, and Other Dental Problems

    Science.gov (United States)

    ... Diabetes, Sexual, & Bladder Problems Diabetes, Gum Disease, & Other Dental Problems How can diabetes affect my mouth? Too ... What if my mouth is sore after my dental work? A sore mouth is common after dental ...

  11. PHYSICOCHEMICAL AND gabonensis GUM EXUDATES A ...

    African Journals Online (AJOL)

    userpc

    fundamental property of a gum therefore is i water solubility ... tion November, 2017. Journal of ... ly or after mechanical incision of the .... and structure of liquid water. .... On the other hand, the strength .... the mineral/aqueous solution interface.".

  12. Effects of acid hydrolysis intensity on the properties of starch/xanthan mixtures.

    Science.gov (United States)

    Jiang, Min; Hong, Yan; Gu, Zhengbiao; Cheng, Li; Li, Zhaofeng; Li, Caiming

    2018-01-01

    The effects of acid hydrolysis intensity on the physicochemical properties of starch/xanthan gum (XG) system were studied. Waxy corn starch (WCS) was subjected to different concentrations of hydrochloric acid, and crystallization and relative molecular weight analysis were performed. The results revealed that the starch granules became smaller during acid hydrolysis. X-ray diffraction pattern analysis showed that the crystal structure did not change with acid hydrolysis. Evaluation of the properties and digestibility of different acid-thinned starch/XG systems indicated that the viscosity of acid-thinned starch/XG decreased with increased acid hydrolysis intensity. Rheological property measurements indicated that the compound systems were a pseudo-plastic fluid, which is a typical weak gel structure. Finally, we show that the WCS1.0M/XG has the highest stability of the tested mixtures. We conclude that adjusting the conditions of acid hydrolysis improves the stability and food quality-enhancing properties of starch. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Preparation of hydroxypropyl corn and amaranth starch hydrolyzate and its evaluation as wall material in microencapsulation.

    Science.gov (United States)

    Kshirsagar, Amol C; Singhal, Rekha S

    2008-06-01

    Hydroxypropylation of starches lends it useful physicochemical and functional properties that are industrially important. The literature on hydroxypropylation using organic solvents for obtaining higher molar substitution (MS) is scantily available. The present work reports on hydroxypropylation of corn and a waxy amaranth starch to different MS with propylene oxide in an alkaline-organic medium (isopropanol). The synthesis was followed in terms of MS. The parameters optimized were starch:isopropanol ratio (w/w), reaction temperature, reaction time and the quantity of alkali required in the process. A maximal MS of 0.180 and 0.162 were obtained for hydroxypropyl corn starch (HPSC) and hydroxypropyl amaranth starch (HPSA), respectively. Enzymatic hydrolysis of the HPSC and HPSA of the above MS was carried out on a 30% (w/v) solution at a pH of 6.5 and 95°C for varying time periods using 0.1% (w/w based on starch) bacterial α-amylase, termamyl. The hydrolysis was terminated by adjusting the pH to 3.5 using 0.1N HCl. The hydrolyzates were characterized in terms of dextrose equivalent and viscosity. The hydrolyzate obtained after 3h of hydrolysis was spray dried and compared to gum arabic with respect to encapsulation of model flavourings, orange oil and lemon oil. Copyright © 2007 Elsevier Ltd. All rights reserved.

  14. 21 CFR 172.695 - Xanthan gum.

    Science.gov (United States)

    2010-04-01

    .... Record the sample as “negative” for xanthan gum if no gel forms or if a soft or brittle gel forms both... more than 1.5 percent of pyruvic acid and “negative” for xanthan gum if the sample contains less than 1... preclude such use. (f) To assure safe use of the additive: (1) The label of its container shall bear, in...

  15. Heterologous expression of two Arabidopsis starch dikinases in potato

    NARCIS (Netherlands)

    Xu, Xuan; Dees, Dianka; Huang, Xing Feng; Visser, Richard G.F.; Trindade, Luisa M.

    2018-01-01

    Starch phosphate esters influence physiochemical properties of starch granules that are essential both for starch metabolism and industrial use of starches. To modify properties of potato starch and understand the effect of starch phosphorylation on starch metabolism in storage starch, the starch

  16. Hydroxyethyl starch for resuscitation

    DEFF Research Database (Denmark)

    Haase, Nicolai; Perner, Anders

    2013-01-01

    PURPOSE OF REVIEW: Resuscitation with hydroxyethyl starch (HES) is controversial. In this review, we will present the current evidence for the use of HES solutions including data from recent high-quality randomized clinical trials. RECENT FINDINGS: Meta-analyses of HES vs. control fluids show clear...

  17. Resistant starch in cassava products

    Directory of Open Access Journals (Sweden)

    Bruna Letícia Buzati Pereira

    2014-06-01

    Full Text Available Found in different foods, starch is the most important source of carbohydrates in the diet. Some factors present in starchy foods influence the rate at which the starch is hydrolyzed and absorbed in vivo. Due the importance of cassava products in Brazilian diet, the objective of this study was to analyze total starch, resistant starch, and digestible starch contents in commercial cassava products. Thirty three commercial cassava products from different brands, classifications, and origin were analyzed. The method used for determination of resistant starch consisted of an enzymatic process to calculate the final content of resistant starch considering the concentration of glucose released and analyzed. The results showed significant differences between the products. Among the flours and seasoned flours analyzed, the highest levels of resistant starch were observed in the flour from Bahia state (2.21% and the seasoned flour from Paraná state (1.93%. Starch, tapioca, and sago showed levels of resistant starch ranging from 0.56 to 1.1%. The cassava products analyzed can be considered good sources of resistant starch; which make them beneficial products to the gastrointestinal tract.

  18. Gum Producers Can Improve Quality Of Gum Marketed and Get Higher Prices

    Science.gov (United States)

    Ralph W. Clements

    1979-01-01

    Acid waste from over-treatment and old, wornout iron cups have contributed significantly to the generally poor quality of gum marketed. Today producers are reluctant to purchase new cups and gutters and invest up to $1.80 per tree for production when the market price for gum averages 14.54 per pound annually. Guidelines are given for improving the quality by...

  19. Rheological and interfacial properties at the equilibrium of almond gum tree exudate (Prunus dulcis) in comparison with gum arabic.

    Science.gov (United States)

    Mahfoudhi, Nesrine; Sessa, Mariarenata; Ferrari, Giovanna; Hamdi, Salem; Donsi, Francesco

    2016-06-01

    Almond gum contains an arabinogalactan-type polysaccharide, which plays an important role in defining its interfacial and rheological properties. In this study, rheological and interfacial properties of almond gum and gum arabic aqueous dispersions were comparatively investigated. The interfacial tension of almond gum and gum arabic aqueous dispersions was measured using the pendant drop method in hexadecane. The asymptotic interfacial tension values for almond gum were significantly lower than the corresponding values measured for gum arabic, especially at high concentration. Rheological properties were characterized by steady and oscillatory tests using a coaxial geometry. Almond gum flow curves exhibited a shear thinning non-Newtonian behavior with a tendency to a Newtonian plateau at low shear rate, while gum arabic flow curves exhibited such behavior only at high shear rate. The influence of temperature (5-50  ℃) on the flow curves was studied at 4% (m/m) gum concentration and the Newtonian viscosities at infinite and at zero shear rate, for gum arabic and almond gum, respectively, were accurately fitted by an Arrhenius-type equation. The dynamic properties of the two gum dispersions were also studied. Both gum dispersions exhibited viscoelastic properties, with the viscous component being predominant in a wider range of concentrations for almond gum, while for gum arabic the elastic component being higher than the elastic one especially at higher concentrations.The rheological and interfacial tension properties of almond gum suggest that it may represent a possible substitute of gum arabic in different food applications. © The Author(s) 2015.

  20. Gummed-up memory: chewing gum impairs short-term recall.

    Science.gov (United States)

    Kozlov, Michail D; Hughes, Robert W; Jones, Dylan M

    2012-01-01

    Several studies have suggested that short-term memory is generally improved by chewing gum. However, we report the first studies to show that chewing gum impairs short-term memory for both item order and item identity. Experiment 1 showed that chewing gum reduces serial recall of letter lists. Experiment 2 indicated that chewing does not simply disrupt vocal-articulatory planning required for order retention: Chewing equally impairs a matched task that required retention of list item identity. Experiment 3 demonstrated that manual tapping produces a similar pattern of impairment to that of chewing gum. These results clearly qualify the assertion that chewing gum improves short-term memory. They also pose a problem for short-term memory theories asserting that forgetting is based on domain-specific interference given that chewing does not interfere with verbal memory any more than tapping. It is suggested that tapping and chewing reduce the general capacity to process sequences.

  1. Optimizing gelling parameters of gellan gum for fibrocartilage tissue engineering.

    Science.gov (United States)

    Lee, Haeyeon; Fisher, Stephanie; Kallos, Michael S; Hunter, Christopher J

    2011-08-01

    Gellan gum is an attractive biomaterial for fibrocartilage tissue engineering applications because it is cell compatible, can be injected into a defect, and gels at body temperature. However, the gelling parameters of gellan gum have not yet been fully optimized. The aim of this study was to investigate the mechanics, degradation, gelling temperature, and viscosity of low acyl and low/high acyl gellan gum blends. Dynamic mechanical analysis showed that increased concentrations of low acyl gellan gum resulted in increased stiffness and the addition of high acyl gellan gum resulted in greatly decreased stiffness. Degradation studies showed that low acyl gellan gum was more stable than low/high acyl gellan gum blends. Gelling temperature studies showed that increased concentrations of low acyl gellan gum and CaCl₂ increased gelling temperature and low acyl gellan gum concentrations below 2% (w/v) would be most suitable for cell encapsulation. Gellan gum blends were generally found to have a higher gelling temperature than low acyl gellan gum. Viscosity studies showed that increased concentrations of low acyl gellan gum increased viscosity. Our results suggest that 2% (w/v) low acyl gellan gum would have the most appropriate mechanics, degradation, and gelling temperature for use in fibrocartilage tissue engineering applications. Copyright © 2011 Wiley Periodicals, Inc.

  2. The enzymatic determination of starch in food, feed and raw materials of the starch industry

    NARCIS (Netherlands)

    Brunt, K.; Sanders, P.; Rozema, T.

    1998-01-01

    An enzymatic starch determination which can be used for the analysis of starch in a very broad range of different samples is evaluated, ranging from starch in plants, feed and food to industrial applications as starch in starch. The method is based on a complete enzymatic conversion of the starch

  3. Design, formulation and evaluation of nicotine chewing gum

    Directory of Open Access Journals (Sweden)

    Abolfazl Aslani

    2012-01-01

    Conclusion: Taste enhancement of nicotine gums was achieved where formulations comprised aspartame as the sweetener and cherry and eucalyptus as the flavoring agents. Nicotine gums of pleasant taste may, therefore, be used as NRT to assist smokers quit smoking.

  4. Evaluation of the suspending properties of Abizia zygia gum on ...

    African Journals Online (AJOL)

    Purpose: Some excipients are currently available for the formulation of pharmaceutical suspensions. ... Method: The suspending properties of Albizia zygia gum (family ... Characterization tests were carried out on purified Albizia zygia gum.

  5. Hydroxyethyl starch in sepsis

    DEFF Research Database (Denmark)

    Haase, Nicolai Rosenkrantz Segelcke

    2014-01-01

    BACKGROUND: Hydroxyethyl starch (HES) is a colloid that has been widely used for fluid resuscitation for decades. The newest generation of HES, tetrastarch, was believed to provide an efficient volume expansion without causing the side effects observed with former HES solutions. However, this bel......BACKGROUND: Hydroxyethyl starch (HES) is a colloid that has been widely used for fluid resuscitation for decades. The newest generation of HES, tetrastarch, was believed to provide an efficient volume expansion without causing the side effects observed with former HES solutions. However...... types of patients is unclear, but so far no group of patients with an overall benefit of HES beyond surrogate markers has been identified. In line with this, the European Medicines Agency's Pharmacovigilance Risk Assessment Committee now recommends that the marketing authorisations of all HES solutions...

  6. Radiolysis of starch

    International Nuclear Information System (INIS)

    Raffi, J.; Saint-Lebe, L.; Berger, G.

    1978-01-01

    In the first part of the paper the results of work on the identification and determination of the gamma ( 60 Co) radiolysis products of maize starch are brought together and, wherever possible, a balance drawn up by chemical class. The second part of the paper deals with the main parameters governing radiolysis: dose, irradiation temperature and atmosphere, water content and the conditions under which the irradiated starch is stored. The third part, devoted to the mechanisms believed to be involved, contains the following conclusions: (a) the formation of radiation-induced products with a carbon skeleton probably results from a breaking of the -C-O-C- chains with rearrangement of the radicals and/or a reaction involving the water and the oxygen - the oxygen has an activating effect which does not fundamentally modify the mechanism, whereas the effect of the water is more complex and varies according to the product; (b) the formation of hydrogen peroxide probably implies the addition of atmospheric oxygen to the radiation-induced hydrogen atoms in the water or to the organic radicals obtained by abstraction of a hydrogen from the starch. Lastly, the different methods envisaged for confirming or improving the mechanistic hypotheses are discussed. (author)

  7. Dependence on the nicotine gum in former smokers.

    Science.gov (United States)

    Etter, Jean-François

    2009-03-01

    We conducted an Internet survey in 2004-2007 in 526 daily users of the nicotine gum, to assess use of, and dependence on the nicotine gum in former smokers. We used modified versions of the Nicotine Dependence Syndrome Scale (NDSS-G), the Cigarette Dependence Scale (CDS-G) and the Fagerström Test (FTND-G). After 30 days, 155 participants (29%) indicated their gum use. Higher dependence on the gum predicted a lower chance of stopping using it at follow-up (odds ratio=0.36 for each standard deviation unit on CDS-G, p=0.001). More long-term (>3 months) than short-term (dependence on the gum than short-term users, as assessed with NDSS-Gum, CDS-Gum and FTND-Gum (all pdependence on the nicotine gum. Lower levels of dependence on the gum predicted cessation of gum use. However, long term use of the nicotine gum has no known serious adverse consequence, and may be beneficial if it prevents late relapse.

  8. Granule properties of paracetamol made with Bombax ceiba gum ...

    African Journals Online (AJOL)

    Bombax ceiba gum was extracted from the calyx of the Bombax flower using both hot and cold water extraction method. The gum was used as binder to prepare paracetamol granules in concentrations of 1, 1.5, 2, and 3 %. Acacia gum was used to prepare the standard at the same concentrations. The granule properties of ...

  9. Quantification and Qualification of Bacteria Trapped in Chewed Gum

    NARCIS (Netherlands)

    Wessel, Stefan W.; van der Mei, Henny C.; Morando, David; Slomp, Anje M.; van de Belt-Gritter, Betsy; Maitra, Amarnath; Busscher, Henk J.

    2015-01-01

    Chewing of gum contributes to the maintenance of oral health. Many oral diseases, including caries and periodontal disease, are caused by bacteria. However, it is unknown whether chewing of gum can remove bacteria from the oral cavity. Here, we hypothesize that chewing of gum can trap bacteria and

  10. Grewia Gum 1: Some Mechanical and Swelling Properties of ...

    African Journals Online (AJOL)

    Erah

    Methods: Compacts (500 mg) of both freeze-dried and air-dried grewia gum were separately ... grewia gum films were compared with films of pullulan and guar gum which were similarly prepared. .... Freeze-drying was carried out using an.

  11. Rheological Modeling and Characterization of Ficus platyphylla Gum Exudates

    Directory of Open Access Journals (Sweden)

    Nnabuk O. Eddy

    2013-01-01

    Full Text Available Ficus platyphylla gum exudates (FP gum have been analyzed for their physicochemical parameters and found to be ionic, mildly acidic, odourless, and yellowish brown in colour. The gum is soluble in water, sparingly soluble in ethanol, and insoluble in acetone and chloroform. The nitrogen (0.39% and protein (2.44% contents of the gum are relatively low. The concentrations of the cations were found to increase according to the following trend, Mn>Fe>Zn>Pb>Cu>Mg>Cd>Ca. Analysis of the FTIR spectrum of the gum revealed vibrations similar to those found in polysaccharides while the scanning electron micrograph indicated that the gum has irregular molecular shapes, arranged randomly. The intrinsic viscosity of FP gum estimated by extrapolating to zero concentrations in Huggins, Kraemer, Schulz-Blaschke, and Martin plots has an average value of 7 dL/g. From the plots of viscosity versus shear rate/speed of rotation and also that of shear stress versus shear rate, FP gum can be classified as a non-Newtonian gum with characteristics-plastic properties. Development of the Master_s curve for FP gum also indicated that the gum prefers to remain in a dilute domain (Cgum (calculated from Arrhenius-Frenkel-Eyring plot was relatively low and indicated the presence of fewer inter- and intramolecular interactions.

  12. 75 FR 44251 - Wood Oils and Gums, and Streptomyces

    Science.gov (United States)

    2010-07-28

    ... ENVIRONMENTAL PROTECTION AGENCY EPA-HQ-OPP-2010-0441; FRL-8829-8 Wood Oils and Gums, and... integrated use in tank mixes with chemical fungicides. The Wood Oils and Gums Registration Review Case no longer contains any other wood oils or gums with active ingredients with registered products except for...

  13. Design, formulation and evaluation of caffeine chewing gum

    Directory of Open Access Journals (Sweden)

    Abolfazl Aslani

    2013-01-01

    Conclusion: In this study, 20 and 50 mg caffeine gums with suitable and desirable properties (i.e., good taste and satisfactory release were formulated. The best flavor for caffeine gum was cinnamon. Both kinds of 20 and 50 mg gums succeeded in content uniformity test.

  14. Natural gums and modified natural gums as sustained-release carriers.

    Science.gov (United States)

    Bhardwaj, T R; Kanwar, M; Lal, R; Gupta, A

    2000-10-01

    Although natural gums and their derivatives are used widely in pharmaceutical dosage forms, their use as biodegradable polymeric materials to deliver bioactive agents has been hampered by the synthetic materials. These natural polysaccharides do hold advantages over the synthetic polymers, generally because they are nontoxic, less expensive, and freely available. Natural gums can also be modified to have tailor-made materials for drug delivery systems and thus can compete with the synthetic biodegradable excipients available in the market. In this review, recent developments in the area of natural gums and their derivatives as carriers in the sustained release of drugs are explored.

  15. Functional properties of irradiated starch

    International Nuclear Information System (INIS)

    Laouini, Wissal

    2011-01-01

    Irradiation is an effective method capable of modifying the functional properties of starches. Its effect depends on the specific structural and molecular organization of starch granules from different botanical sources. In this study, we have studied the effect of gamma irradiation (3, 5, 10, 20, 35, 50 kGy) on the rheological properties of some varieties of starch (potato, cassava and wheat). First, we were interested in determining dry matter content; the results showed that the variation in dry matter compared to the control (native starch) is almost zero. So it does not depend on the dose of irradiation. Contrariwise, it differs from a botanical species to another. The viscometer has shown that these starches develop different behaviors during shearing. The native potato starch gave the highest viscosity followed by wheat and cassava which have almost similar viscosities. For all varieties, the viscosity of starch decreases dramatically with an increasing dose of irradiation. At high doses (35 and 50 kGy) the behavior of different starch is similar to that of a viscous pure liquid. The textural analysis via the back-extrusion test showed that increasing the dose of radiation causes a decrease in extrusion force and the energy spent of the different starch throughout the test. Indeed, the extrusion resistance decreases with increasing dose.

  16. Chewing gum moderates the vigilance decrement.

    OpenAIRE

    Morgan, K.; Johnson, A.J.; Miles, C..

    2014-01-01

    We examine the impact of chewing gum on a Bakan-type vigilance task that requires the continual updating of short-term order memory. Forty participants completed a 30-min auditory Bakan-task either with, or without, the requirement to chew gum. Self-rated measures of mood were taken both pre- and post-task. As expected, the vigilance task produced a time-dependent performance decrement indexed via decreases in target detections and lengthened correct reaction times (RTs), and a reduction in p...

  17. Neem Gum as a Binder in a Formulated Paracetamol Tablet with Reference to Acacia Gum BP

    OpenAIRE

    Ogunjimi, Abayomi Tolulope; Alebiowu, Gbenga

    2014-01-01

    This study determined the physical, compressional, and binding properties of neem gum (NMG) obtained from the trunk of Azadirachta indica (A Juss) in a paracetamol tablet formulation in comparison with official Acacia gum BP (ACA). The physical and flow properties were evaluated using density parameters: porosity, Carr’s index, Hausner’s ratio, and flow rate. Compressional properties were analyzed using Heckel and Kawakita equations. The tensile strength, brittle fracture index, and crushing ...

  18. Chewing gum differentially affects aspects of attention in healthy subjects.

    Science.gov (United States)

    Tucha, Oliver; Mecklinger, Lara; Maier, Kerstin; Hammerl, Marianne; Lange, Klaus W

    2004-06-01

    In a study published previously in this journal (Wilkinson et al., 2002), the effect of chewing gum on cognitive functioning was examined. The results of this study indicated that chewing a piece of gum results in an improvement of working memory and of both immediate and delayed recall of words but not of attention. In the present study, memory and a variety of attentional functions of healthy adult participants were examined under four different conditions: no chewing, mimicking chewing movements, chewing a piece of tasteless chewing gum and chewing a piece of spearmint flavoured chewing gum. The sequence of conditions was randomised across participants. The results showed that the chewing of gum did not improve participants' memory functions. Furthermore, chewing may differentially affect specific aspects of attention. While sustained attention was improved by the chewing of gum, alertness and flexibility were adversely affected by chewing. In conclusion, claims that the chewing a gum improves cognition should be viewed with caution.

  19. Starch Biosynthesis in Crop Plants

    Directory of Open Access Journals (Sweden)

    Ian J. Tetlow

    2018-05-01

    Full Text Available Starch is a water-insoluble polyglucan synthesized inside the plastids of plant tissues to provide a store of carbohydrate. Starch harvested from plant storage organs has probably represented the major source of calories for the human diet since before the dawn of civilization. Following the advent of agriculture and the building of complex societies, humans have maintained their dependence on high-yielding domesticated starch-forming crops such as cereals to meet food demands, livestock production, and many non-food applications. The top three crops in terms of acreage are cereals, grown primarily for the harvestable storage starch in the endosperm, although many starchy tuberous crops also provide an important source of calories for various communities around the world. Despite conservation in the core structure of the starch granule, starches from different botanical sources show a high degree of variability, which is exploited in many food and non-food applications. Understanding the factors underpinning starch production and its final structure are of critical importance in guiding future crop improvement endeavours. This special issue contains reviews on these topics and is intended to be a useful resource for researchers involved in improvement of starch-storing crops.

  20. Physicochemical properties of maca starch.

    Science.gov (United States)

    Zhang, Ling; Li, Guantian; Wang, Sunan; Yao, Weirong; Zhu, Fan

    2017-03-01

    Maca (Lepidium meyenii Walpers) is gaining research attention due to its unique bioactive properties. Starch is a major component of maca roots, thus representing a novel starch source. In this study, the properties of three maca starches (yellow, purple and black) were compared with commercially maize, cassava, and potato starches. The starch granule sizes ranged from 9.0 to 9.6μm, and the granules were irregularly oval. All the maca starches presented B-type X-ray diffraction patterns, with the relative degree of crystallinity ranging from 22.2 to 24.3%. The apparent amylose contents ranged from 21.0 to 21.3%. The onset gelatinization temperatures ranged from 47.1 to 47.5°C as indicated by differential scanning calorimetry. Significant differences were observed in the pasting properties and textural parameters among all of the studied starches. These characteristics suggest the utility of native maca starch in products subjected to low temperatures during food processing and other industrial applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Flavor release measurement from gum model system

    DEFF Research Database (Denmark)

    Ovejero-López, I.; Haahr, Anne-Mette; van den Berg, Frans W.J.

    2004-01-01

    composition can be measured by both instrumental and sensory techniques, providing comparable information. The peppermint oil level (0.5-2% w/w) in the gum influenced both the retronasal concentration and the perceived peppermint flavor. The sweeteners' (sorbitol or xylitol) effect is less apparent. Sensory...

  2. Enzymatic production of polysaccharides from gum tragacanth

    DEFF Research Database (Denmark)

    2014-01-01

    Plant polysaccharides, relating to the field of natural probiotic components, can comprise structures similar to human milk oligosaccharides. A method for enzymatic hydrolysis of gum tragacanth from the bush-like legumes of the genus Astragalus, using a combination of pectin hydrolases...

  3. Effect of gum hardness on chewing pattern.

    Science.gov (United States)

    Plesh, O; Bishop, B; McCall, W

    1986-06-01

    Chewing rhythms are set by a putative central pattern generator whose output is influenced by sensory feedback. In this study we assessed how an altered feedback imposed by changing the hardness of a gum bolus modifies the timing of chewing, the maximal gape, and the activity in the masseter muscle on the chewing side. Ten adult subjects with no orofacial dysfunction chewed a standard piece of soft or hard gum for at least 3 min in random order. Vertical jaw movements were recorded with a kinesiograph and activity of the masseter muscle was recorded and integrated from surface EMG electrodes. The subjects sat in a dental chair and viewed a video lecture to distract their attention from chewing; they were instructed to chew on the right molars. Cycle-by-cycle analysis showed that 9 of the 10 subjects chewed the hard gum more slowly than the soft with no significant change in gape. The increases in cycle duration were due to changes in the duration of the opening and occlusal phases. The duration of closing was not significantly changed even though the duration and level of masseter activity were both significantly increased. We conclude that gum hardness by altering proprioceptive feedback modifies the output of the masticatory central pattern generator in such a way that the temporal aspects of chewing and the output of the masseteric motor pool are affected.

  4. Tuliposides and tulipalins in tulip Gum

    NARCIS (Netherlands)

    Lubbe, A.; Verpoorte, R.; Gude, H.; Dijkema, M.H.G.E.

    2013-01-01

    Gummosis in tulip bulbs is one of the negative effects of ethylene gas that is produced during storage by Fusarium-infected bulbs on the healthy bulbs. Several aspects of the gummosis process, like the factors inducing it, the underlying carbohydrate metabolism and the composition of the gum have

  5. Evaluation of resistant starch, glycemic index and fortificants content of premix rice coated with various concentrations and types of edible coating materials

    Science.gov (United States)

    Yulianto, W. A.; Susiati, A. M.; Adhini, H. A. N.

    2018-01-01

    The incidence of diabetes in Indonesia has been increasing year by year. Diets with a low glycemic index and high resistant starch foods can assist diabetics in controlling their blood glucose levels. Diabetics are known to have micro-nutrient deficiencies of chromium, magnesium and vitamin D that can be overcome by consuming parboiled rice fortified by use of a coating method. The fortification of parboiled rice (premix rice) can be achieved by coating with HPMC (hydroxypropyl methyl cellulose), MC (methyl cellulose), CMC (carboxyl methyl cellulose), gum arabic and rice starch. This research aimed to evaluate the levels of resistant starch, glycemic index and fortificants of premix rice coated with different concentrations and types of edible coating materials. This research used completely randomized design, with treatments to the concentrations and the types of edible coating (HPMC, CMC, MC, gum arabic and rice starch). The concentrations of edible coating were 0.15%, 0.2% and 0.25% for cellulose derivative coatings; 25%, 30%, 35% for gum arabic and 2%, 3.5% and 5% for rice starch. This research shows that fortified premix rice coated with various concentrations and types of edible coating materials is high in resistant starch and has a low glycemic index. The coating treatment affects the levels of magnesium and vitamin D, but does not affect the levels of chromium in parboiled rice. The premix rice with a low glycemic index and high nutrient content (chromium, magnesium and vitamin D) was premix rice coated by CMC 0.25% and HPMC 0.25% with glycemic indeces of 39.34 and 38.50, respectively.

  6. Starches, Sugars and Obesity

    Directory of Open Access Journals (Sweden)

    Erik E. J. G. Aller

    2011-03-01

    Full Text Available The rising prevalence of obesity, not only in adults but also in children and adolescents, is one of the most important public health problems in developed and developing countries. As one possible way to tackle obesity, a great interest has been stimulated in understanding the relationship between different types of dietary carbohydrate and appetite regulation, body weight and body composition. The present article reviews the conclusions from recent reviews and meta-analyses on the effects of different starches and sugars on body weight management and metabolic disturbances, and provides an update of the most recent studies on this topic. From the literature reviewed in this paper, potential beneficial effects of intake of starchy foods, especially those containing slowly-digestible and resistant starches, and potential detrimental effects of high intakes of fructose become apparent. This supports the intake of whole grains, legumes and vegetables, which contain more appropriate sources of carbohydrates associated with reduced risk of cardiovascular and other chronic diseases, rather than foods rich in sugars, especially in the form of sugar-sweetened beverages.

  7. Effect of GutsyGum(tm), A Novel Gum, on Subjective Ratings of Gastro Esophageal Reflux Following A Refluxogenic Meal.

    Science.gov (United States)

    Brown, Rachel; Sam, Cecilia H Y; Green, Tim; Wood, Simon

    2015-06-01

    Chewing gum alleviates symptoms of gastro-esophageal reflux (GER) following a refluxogenic meal. GutsyGum(tm), a chewing gum developed to alleviate the symptoms of GER contains calcium carbonate, with a proprietary blend of licorice extract, papain, and apple cider vinegar (GiGs®). The efficacy of GutsyGum(tm) was determined in alleviating the symptoms of GER after a refluxogenic meal compared to placebo gum. This double-blind, placebo-controlled-crossover trial with a one-week washout between treatments had 24 participants with a history of GER consume a refluxogenic meal and then chew GutsyGum(tm) or placebo gum. Participants completed GER symptom questionnaires, consisting of symptom based 10 cm Visual Analogue Scales, immediately following the meal and then at regular intervals out to four hours postmeal. Adjusted mean ± SEM heartburn score (15-min postmeal to 240 min) was significantly lower in GutsyGum(tm) than in placebo gum treatment (0.81 ± 0.20 vs. 1.45 ± 0.20 cm; p = 0.034). Mean acid reflux score was significantly lower in GutsyGum(tm) than in placebo treatment (0.72 ± 0.19 vs. 1.46 ± 0.19 cm; p = 0.013). There were no significant differences for any of the secondary outcomes. However, pain approached significance with less pain reported in GutsyGum(tm) versus placebo treatment (0.4 ± 0.2 vs. 0.9 ± 0.2 cm; p = 0.081). Although nausea (p = 0.114) and belching (p = 0.154) were lower following GutsyGum(tm), the difference was not statistically significant. GutsyGum(tm) is more effective than a placebo gum in alleviating primary symptoms of heartburn and acid reflux (Clinical Trial Registration: ACTRN12612000973819).

  8. Substituent distribution within cross-linked and hydroxypropylated sweet potato starch and potato starch

    NARCIS (Netherlands)

    Zhao, J.; Schols, H.A.; Chen Zenghong,; Jin Zhengyu,; Buwalda, P.L.; Gruppen, H.

    2012-01-01

    Revealing the substituents distribution within starch can help to understand the changes of starch properties after modification. The distribution of substituents over cross-linked and hydroxypropylated sweet potato starch was investigated and compared with modified potato starch. The starches were

  9. Competition in the gum arabic market: a game theoretic modelling approach

    NARCIS (Netherlands)

    Rahim, A.; Ierland, van E.C.; Weikard, H.P.

    2010-01-01

    Gum arabic is mainly produced from two Acacias that are found in the gum belt of Sub-Saharan Africa. These are Acacia senegal that produces high quality gum and Acacia seyal that produces low quality gum. In recent years the gum market structure has changed and Sudan lost its near monopoly position

  10. Physico-chemical study on guar gum

    International Nuclear Information System (INIS)

    Mahmoud, Nahla Mubarak

    2000-05-01

    Guar plant is an annual summer plant and it can resist diseases, pests and drought. Guar gum is used in a lot of industries. The present study deals with some physical properties of two commercial grade samples of guar gum cyamopsis tetragonoloba which where produced in 1996 and 1997 seasons (S 1 and S 2 respectively). Our analytical data are compared with those of previous workers in this area and international quality. Guar gum (S 2 ) is separated into water-insoluble components. Three fractions were obtained from the water-soluble components by fractional participation using acetone. Guar gum powder is yellowish white; the water-insoluble component is brownish white. Comparison study between gum samples (S 1 and S 2 ) and water-insoluble fraction (1) and water-soluble fractions are close to each other in their physico-properties. chemical All samples and fractions contain galactomannan polysaccharide as explained by infra-red spectra.Moisture contents for the gum samples were 5.2% and 7.8% and that for the water-insoluble fraction 4.7% while that for fraction samples were 5.2%-7.5% ash contents for the gum samples was 0.81% and 1.14% and for the water-insoluble component 0.88% while the contents in the fractions between 0.5%-0.66%. Nitrogen content determination showed that the gum samples had value of 0.678% and 0.732% and water -insoluble fraction had a value of 0.118%. The values decreased in the water-soluble fractions giving 0.049%, 0.053 and 0.056%. Water-soluble component and its fractions record the following results: pH measurements showed that the water-soluble component had pH 6.70 and 6.84 while its fractions had pH 5.90 and 7.00. Viscosity measurements showed that water-soluble fractions had intrinsic viscosity of 6.4 and 6.8 dL. g -1 . The fractions derived from water-soluble fraction had intrinsic viscosity of 6.6, 7 and 7.5 dl. g -1 . Using Mark-Howink equation, calculated average molecular weights for the water-soluble components were 7.01x10 5

  11. Powder and compaction characteristics of pregelatinized starches.

    Science.gov (United States)

    Rojas, J; Uribe, Y; Zuluaga, A

    2012-06-01

    Pregelatinized starch is widely used as a pharmaceutical aid, especially as a filler-binder. It is known that the tableting performance of excipients could be affected by their source. The aim of this study was to evaluate the powder and tableting properties of pregelatinized starches obtained from yucca, corn and rice and compare those properties with those of Starch 1500. This material had the lowest particle size, and porosity and largest density and best flow. However, yucca starch and corn starch showed an irregular granule morphology, better compactibility and compressibility than Starch 1500. Their onset of plastic deformation and their strain rate sensitivity was comparable to that of Starch 1500. These two materials showed compact disintegration slower that Starch 1500. Conversely, rice starch showed a high elasticity, and friability, low compactibility, which are undesirable for direct compression. This study demonstrated the potential use of pregelatinized starches, especially those obtained from yucca and corn as direct compression filler-binders.

  12. Sixth taste – starch taste?

    Directory of Open Access Journals (Sweden)

    Zygmunt Zdrojewicz

    2017-06-01

    Full Text Available Scientists from Oregon State University, USA, came up with the newest theory of the sixth taste – starch taste that might soon join the basic five tastes. This argument is supported by studies done on both animals and humans, the results of which seem to indicate the existence of separate receptors for starch taste, others than for sweet taste. Starch is a glucose homopolymer that forms an α-glucoside chain called glucosan or glucan. This polysaccharide constitutes the most important source of carbohydrates in food. It can be found in groats, potatoes, legumes, grains, manioc and corn. Apart from its presence in food, starch is also used in textile, pharmaceutical, cosmetic and stationery industries as well as in glue production. This polysaccharide is made of an unbranched helical structure – amylose (15–20%, and a structure that forms branched chains – amylopectin (80–85%. The starch structure, degree of its crystallisation or hydration as well as its availability determine the speed of food-contained starch hydrolysis by amylase. So far, starch has been considered tasteless, but the newest report shows that for people of different origins it is associated with various aliments specific for each culture. Apart from a number of scientific experiments using sweet taste inhibitors, the existence of the sixth taste is also confirmed by molecular studies. However, in order to officially include starch taste to the basic human tastes, it must fulfil certain criteria. The aim of the study is to present contemporary views on starch.

  13. Chemical Modifications of Starch: Microwave Effect

    OpenAIRE

    Lewicka, Kamila; Siemion, Przemysław; Kurcok, Piotr

    2015-01-01

    This paper presents basic methods of starch chemical modification, the effect of microwave radiation on the modification process, and the physicochemical properties of starch. It has been shown that the modifications contribute to improvement of the material performance and likewise to significant improvement of its mechanical properties. As a result, more and more extensive use of starch is possible in various industries. In addition, methods of oxidized starch and starch esters preparation ...

  14. Gum Arabic authentication and mixture quantification by near infrared spectroscopy

    DEFF Research Database (Denmark)

    Dong, Yongjiang; Sørensen, Klavs Martin; He, Sailing

    2017-01-01

    A rapid and reliable method is developed for Gum Arabic authentication based on Near Infrared (NIR) spectroscopy and chemometric methods. On a large industrial collection of authentic gum Arabics, the two major Acacia gum species, Acacia senegal and Acacia seyal could be assigned perfectly...... by the NIR spectroscopic method. In addition, a partial least squares (PLS) regression model is calibrated to predict the blending percentage of the two pure gum types, producing an accuracy, root mean square error of cross validation (RMSECV) of 2.8%. Sampling of the Gum Arabic ‘tears’ is discussed......, and it was determined that subsamples from three ‘tears’ is required for a representative result. It is concluded that NIR spectroscopy is a very powerful and reliable method for authenticity testing of Gum Arabic species....

  15. Development of natural gum based fast disintegrating tablets of glipizide

    OpenAIRE

    Antesh Kumar Jha; Dipak Chetia

    2012-01-01

    Dysphagia and risk of choking are leading causes of patient non-compliance in the self-administration of conventional tablets. To overcome these limitations of conventional tablets fast-disintegrating tablets were developed, using natural gums. Natural gums were evaluated for bulk swelling capacity. Powder mix containing natural gums and glipizide was evaluated for water sorption, swelling index and capillary action. For faster onset and immediate hypoglycemic action, the fast disintegrating ...

  16. Guar gum: processing, properties and food applications—A Review

    OpenAIRE

    Mudgil, Deepak; Barak, Sheweta; Khatkar, Bhupendar Singh

    2011-01-01

    Guar gum is a novel agrochemical processed from endosperm of cluster bean. It is largely used in the form of guar gum powder as an additive in food, pharmaceuticals, paper, textile, explosive, oil well drilling and cosmetics industry. Industrial applications of guar gum are possible because of its ability to form hydrogen bonding with water molecule. Thus, it is chiefly used as thickener and stabilizer. It is also beneficial in the control of many health problems like diabetes, bowel movement...

  17. Design, formulation and evaluation of nicotine chewing gum

    OpenAIRE

    Abolfazl Aslani; Sahar Rafiei

    2012-01-01

    Background: Nicotine replacement therapy (NRT) can help smokers to quit smoking. Nicotine chewing gum has attracted the attention from pharmaceutical industries to offer it to consumers as an easily accessible NRT product. However, the bitter taste of such gums may compromise their acceptability by patients. This study was, therefore, designed to develop 2 and 4 mg nicotine chewing gums of pleasant taste, which satisfy the consumers the most. Materials and Methods: Nicotine, sugar, liquid...

  18. Flavor release measurement from gum model system.

    Science.gov (United States)

    Ovejero-López, Isabel; Haahr, Anne-Mette; van den Berg, Frans; Bredie, Wender L P

    2004-12-29

    Flavor release from a mint-flavored chewing gum model system was measured by atmospheric pressure chemical ionization mass spectroscopy (APCI-MS) and sensory time-intensity (TI). A data analysis method for handling the individual curves from both methods is presented. The APCI-MS data are ratio-scaled using the signal from acetone in the breath of subjects. Next, APCI-MS and sensory TI curves are smoothed by low-pass filtering. Principal component analysis of the individual curves is used to display graphically the product differentiation by APCI-MS or TI signals. It is shown that differences in gum composition can be measured by both instrumental and sensory techniques, providing comparable information. The peppermint oil level (0.5-2% w/w) in the gum influenced both the retronasal concentration and the perceived peppermint flavor. The sweeteners' (sorbitol or xylitol) effect is less apparent. Sensory adaptation and sensitivity differences of human perception versus APCI-MS detection might explain the divergence between the two dynamic measurement methods.

  19. Validating the applicability of the GUM procedure

    Science.gov (United States)

    Cox, Maurice G.; Harris, Peter M.

    2014-08-01

    This paper is directed at practitioners seeking a degree of assurance in the quality of the results of an uncertainty evaluation when using the procedure in the Guide to the Expression of Uncertainty in Measurement (GUM) (JCGM 100 : 2008). Such assurance is required in adhering to general standards such as International Standard ISO/IEC 17025 or other sector-specific standards. We investigate the extent to which such assurance can be given. For many practical cases, a measurement result incorporating an evaluated uncertainty that is correct to one significant decimal digit would be acceptable. Any quantification of the numerical precision of an uncertainty statement is naturally relative to the adequacy of the measurement model and the knowledge used of the quantities in that model. For general univariate and multivariate measurement models, we emphasize the use of a Monte Carlo method, as recommended in GUM Supplements 1 and 2. One use of this method is as a benchmark in terms of which measurement results provided by the GUM can be assessed in any particular instance. We mainly consider measurement models that are linear in the input quantities, or have been linearized and the linearization process is deemed to be adequate. When the probability distributions for those quantities are independent, we indicate the use of other approaches such as convolution methods based on the fast Fourier transform and, particularly, Chebyshev polynomials as benchmarks.

  20. Phytase application in chewing gum - A technical assessment

    DEFF Research Database (Denmark)

    Nielsen, Anne Veller Friis; Meyer, Anne S.

    2016-01-01

    either prior to ingestion, i.e. in the food, or post ingestion, i.e. in the human gastrointestinal tract. We have assessed the technical aspects of formulation and release of phytase added to chewing gum as a delivery vehicle. Phytases from Aspergillus niger and Escherichia coli incorporated into chewing...... gum were released quantitatively upon chewing and retained phytase activity (50-80% of the enzyme activity added was released within 10 minutes). Initial evaluations of phytase chewing gum shelf life showed good stability after 48 days of storage of the chewing gum at ambient conditions....

  1. Guar gum: processing, properties and food applications-A Review.

    Science.gov (United States)

    Mudgil, Deepak; Barak, Sheweta; Khatkar, Bhupendar Singh

    2014-03-01

    Guar gum is a novel agrochemical processed from endosperm of cluster bean. It is largely used in the form of guar gum powder as an additive in food, pharmaceuticals, paper, textile, explosive, oil well drilling and cosmetics industry. Industrial applications of guar gum are possible because of its ability to form hydrogen bonding with water molecule. Thus, it is chiefly used as thickener and stabilizer. It is also beneficial in the control of many health problems like diabetes, bowel movements, heart disease and colon cancer. This article focuses on production, processing, composition, properties, food applications and health benefits of guar gum.

  2. Design starch: stochastic modeling of starch granule biogenesis.

    Science.gov (United States)

    Raguin, Adélaïde; Ebenhöh, Oliver

    2017-08-15

    Starch is the most widespread and abundant storage carbohydrate in plants and the main source of carbohydrate in the human diet. Owing to its remarkable properties and commercial applications, starch is still of growing interest. Its unique granular structure made of intercalated layers of amylopectin and amylose has been unraveled thanks to recent progress in microscopic imaging, but the origin of such periodicity is still under debate. Both amylose and amylopectin are made of linear chains of α-1,4-bound glucose residues, with branch points formed by α-1,6 linkages. The net difference in the distribution of chain lengths and the branching pattern of amylose (mainly linear), compared with amylopectin (racemose structure), leads to different physico-chemical properties. Amylose is an amorphous and soluble polysaccharide, whereas amylopectin is insoluble and exhibits a highly organized structure of densely packed double helices formed between neighboring linear chains. Contrarily to starch degradation that has been investigated since the early 20th century, starch production is still poorly understood. Most enzymes involved in starch growth (elongation, branching, debranching, and partial hydrolysis) are now identified. However, their specific action, their interplay (cooperative or competitive), and their kinetic properties are still largely unknown. After reviewing recent results on starch structure and starch growth and degradation enzymatic activity, we discuss recent results and current challenges for growing polysaccharides on granular surface. Finally, we highlight the importance of novel stochastic models to support the analysis of recent and complex experimental results, and to address how macroscopic properties emerge from enzymatic activity and structural rearrangements. © 2017 The Author(s).

  3. Design starch: stochastic modeling of starch granule biogenesis

    Science.gov (United States)

    Ebenhöh, Oliver

    2017-01-01

    Starch is the most widespread and abundant storage carbohydrate in plants and the main source of carbohydrate in the human diet. Owing to its remarkable properties and commercial applications, starch is still of growing interest. Its unique granular structure made of intercalated layers of amylopectin and amylose has been unraveled thanks to recent progress in microscopic imaging, but the origin of such periodicity is still under debate. Both amylose and amylopectin are made of linear chains of α-1,4-bound glucose residues, with branch points formed by α-1,6 linkages. The net difference in the distribution of chain lengths and the branching pattern of amylose (mainly linear), compared with amylopectin (racemose structure), leads to different physico-chemical properties. Amylose is an amorphous and soluble polysaccharide, whereas amylopectin is insoluble and exhibits a highly organized structure of densely packed double helices formed between neighboring linear chains. Contrarily to starch degradation that has been investigated since the early 20th century, starch production is still poorly understood. Most enzymes involved in starch growth (elongation, branching, debranching, and partial hydrolysis) are now identified. However, their specific action, their interplay (cooperative or competitive), and their kinetic properties are still largely unknown. After reviewing recent results on starch structure and starch growth and degradation enzymatic activity, we discuss recent results and current challenges for growing polysaccharides on granular surface. Finally, we highlight the importance of novel stochastic models to support the analysis of recent and complex experimental results, and to address how macroscopic properties emerge from enzymatic activity and structural rearrangements. PMID:28673938

  4. Stabilization of emulsions by gum tragacanth (Astragalus spp.) correlates to the galacturonic acid content and methoxylation degree of the gum

    DEFF Research Database (Denmark)

    Ahmadi Gavlighi, Hassan; Meyer, Anne S.; Abang Zaidel, Dayang Norulfairuz

    2013-01-01

    Gum tragacanth samples from six species of Iranian Astragalus bush plants (“goat's-horn”) were evaluated for their emulsion stabilizing effects and their detailed chemical composition in order to examine any possible correlation between the make-up and the emulsion stabilizing properties of gum......:50 (A. rahensis, A. microcephalus, A. compactus) or tipped toward higher bassorin than tragacanthin (A. gossypinus). The monosaccharide make-up of the six gums also varied, but all the gums contained relatively high levels of galacturonic acid (∼100–330 mg/g), arabinose (50–360 mg/g), xylose (∼150...

  5. Chemical Modifications of Starch: Microwave Effect

    Directory of Open Access Journals (Sweden)

    Kamila Lewicka

    2015-01-01

    Full Text Available This paper presents basic methods of starch chemical modification, the effect of microwave radiation on the modification process, and the physicochemical properties of starch. It has been shown that the modifications contribute to improvement of the material performance and likewise to significant improvement of its mechanical properties. As a result, more and more extensive use of starch is possible in various industries. In addition, methods of oxidized starch and starch esters preparation are discussed. Properties of microwave radiation and its impact on starch (with particular regard to modifications described in literature are characterized.

  6. Starch as a source, starch as a sink: the bifunctional role of starch in carbon allocation.

    Science.gov (United States)

    MacNeill, Gregory J; Mehrpouyan, Sahar; Minow, Mark A A; Patterson, Jenelle A; Tetlow, Ian J; Emes, Michael J

    2017-07-20

    Starch commands a central role in the carbon budget of the majority of plants on earth, and its biological role changes during development and in response to the environment. Throughout the life of a plant, starch plays a dual role in carbon allocation, acting as both a source, releasing carbon reserves in leaves for growth and development, and as a sink, either as a dedicated starch store in its own right (in seeds and tubers), or as a temporary reserve of carbon contributing to sink strength, in organs such as flowers, fruits, and developing non-starchy seeds. The presence of starch in tissues and organs thus has a profound impact on the physiology of the growing plant as its synthesis and degradation governs the availability of free sugars, which in turn control various growth and developmental processes. This review attempts to summarize the large body of information currently available on starch metabolism and its relationship to wider aspects of carbon metabolism and plant nutrition. It highlights gaps in our knowledge and points to research areas that show promise for bioengineering and manipulation of starch metabolism in order to achieve more desirable phenotypes such as increased yield or plant biomass. © The Author 2017. Published by Oxford University Press on behalf of the Society for Experimental Biology. All rights reserved. For permissions, please email: journals.permissions@oup.com.

  7. Hydrocolloids Decrease the Digestibility of Corn Starch, Soy Protein, and Skim Milk and the Antioxidant Capacity of Grape Juice.

    Science.gov (United States)

    Yi, Yue; Jeon, Hyeong-Ju; Yoon, Sun; Lee, Seung-Min

    2015-12-01

    Hydrocolloids have many applications in foods including their use in dysphagia diets. We aimed to evaluate whether hydrocolloids in foods affect the digestibility of starch and protein, and their effects on antioxidant capacity. The thickening hydrocolloids: locust bean gum and carboxymethyl cellulose, and the gel-forming agents: agar agar, konjac-glucomannan, and Hot & Soft Plus were blended with corn starch and soy protein, skim milk, or grape juice and were examined for their in vitro-digestability by comparing the reducing sugar and trichloroacetic acid (TCA)-soluble peptide, for antioxidant capacity by total polyphenol contents and the 2,2-diphenyl-1-picrylhydrazyl radical scavenging activity. The hydrocolloids resulted in a decrease in starch digestibility with the gel-forming agents. Hydrocolloids diminished TCA-soluble peptides in skim milk compared to soy protein with the exception of locust bean gum and decreased free radical scavenging capacities and total phenolic contents in grape juice. Our findings may provide evidence for the use of hydro-colloids for people at risk of nutritional deficiencies such as dysphagia patients.

  8. Neem gum as a binder in a formulated paracetamol tablet with reference to Acacia gum BP.

    Science.gov (United States)

    Ogunjimi, Abayomi Tolulope; Alebiowu, Gbenga

    2014-04-01

    This study determined the physical, compressional, and binding properties of neem gum (NMG) obtained from the trunk of Azadirachta indica (A Juss) in a paracetamol tablet formulation in comparison with official Acacia gum BP (ACA). The physical and flow properties were evaluated using density parameters: porosity, Carr's index, Hausner's ratio, and flow rate. Compressional properties were analyzed using Heckel and Kawakita equations. The tensile strength, brittle fracture index, and crushing strength-friability/disintegration time ratio were used to evaluate the mechanical properties of paracetamol tablets while the drug release properties of the tablets were assessed using disintegration time and dissolution times. Tablet formulations containing NMG exhibited faster onset and higher amount of plastic deformation during compression than those containing ACA. Neem gum produced paracetamol tablets with lower mechanical strength; however, the tendency of the tablets to cap or laminate was lower when compared to those containing ACA. Inclusion of NMG improved the balance between binding and disintegration properties of paracetamol tablets produced than those containing ACA. Neem gum produced paracetamol tablets with lower disintegration and dissolution times than those containing ACA.

  9. Preparation and characterization of dialdehyde starch urea (DASU ...

    African Journals Online (AJOL)

    Dialdehyde starch urea (DASU) was prepared by the reaction of dialdehyde starch (DAS) from periodate oxidized cassava starch with urea, which was then used to adsorb Co(II), Pb(II) and Zn(II) ions from aqueous solution. Starch modified starches and starch complexes were characterized by Fourier transform infrared ...

  10. Intrinsic viscosity of guar gum in sweeteners solutions | Samavati ...

    African Journals Online (AJOL)

    Rheological methods were applied to study the effect of sweeteners on the rheological behavior of guar gum in dilute solutions. The concentration of the sweeteners were 0.1, 0.2%w/v for aspartame, acesulfame-k and cyclamate, and 0.001, 0.002%w/v for neotame. Gum was evaluated for intrinsic viscosity by various ...

  11. Impact of welan gum on tricalcium aluminate–gypsum hydration

    International Nuclear Information System (INIS)

    Ma Lei; Zhao Qinglin; Yao Chukang; Zhou Mingkai

    2012-01-01

    The retarding effect of welan gum on tricalcium aluminate–gypsum hydration, as a partial system of ordinary Portland cement (OPC) hydration, was investigated with several methods. The tricalcium aluminate–gypsum hydration behavior in the presence or absence of welan gum was researched by field emission gun scanning electron microscopy, X-ray diffraction and zeta potential analysis. Meanwhile, we studied the surface electrochemical properties and adsorption characteristics of welan gum by utilizing a zeta potential analyzer and UV–VIS absorption spectrophotometer. By adding welan gum, the morphology change of ettringite and retardation of hydration stages in tricalcium aluminate–gypsum system was observed. Moreover, we detected the adsorption behavior and zeta potential inversion of tricalcium aluminate and ettringite, as well as a rapid decrease in the zeta potential of tricalcium aluminate–gypsum system. The reduction on nucleation rate of ettringite and hydration activity of C 3 A was also demonstrated. Thus, through the adsorption effect, welan gum induces a retarding behavior in tricalcium aluminate–gypsum hydration. Highlights: ► Adsorption characteristics of welan gum on C 3 A and ettringite have been studied. ► C 3 A–gypsum hydration behavior and the hydration products are examined in L/S = 3. ► Welan gum retards the process of C 3 A–gypsum hydration. ► The addition of welan gum changes the nucleation growth of ettringite.

  12. Gum from the bark of Anogeissius leiocarpus as a potential ...

    African Journals Online (AJOL)

    Gum from the bark of Anogeissius leiocarpusas a potential pharmaceutical raw material – granule properties. Philip F Builders, Olubayo O Kunle, Yetunde C Isimi. Abstract. With the continuous effort to discover and produce cheap but high quality excipients for drug production Anogeissius leiocarpus gum (ALG), a brownish ...

  13. Grewia Gum 1: Some Mechanical and Swelling Properties of ...

    African Journals Online (AJOL)

    Purpose: To study the mechanical and dynamic swelling properties of grewia gum, evaluate its compression behaviour and determine the effect of drying methods on its properties. Methods: Compacts (500 mg) of both freeze-dried and air-dried grewia gum were separately prepared by compression on a potassium bromide ...

  14. Increased gum arabic production after infestation of Acacia senegal ...

    African Journals Online (AJOL)

    Jane

    2011-07-20

    Jul 20, 2011 ... chemical properties of gum were determined for infested and control trees. A. senegal infested by A. ... also in the textile, pottery, lithography, cosmetics and ... Deforestation within the gum belt has lead to an increase in desert .... Atomic Absorption = V*N EDTA*1000/Volume of extract (mg/l). Where, V is the ...

  15. Gellan Gum: Fermentative Production, Downstream Processing and Applications

    Directory of Open Access Journals (Sweden)

    Ishwar B. Bajaj

    2007-01-01

    Full Text Available The microbial exopolysaccharides are water-soluble polymers secreted by microorganisms during fermentation. The biopolymer gellan gum is a relatively recent addition to the family of microbial polysaccharides that is gaining much importance in food, pharmaceutical and chemical industries due to its novel properties. It is commercially produced by C. P. Kelco in Japan and the USA. Further research and development in biopolymer technology is expected to expand its use. This article presents a critical review of the available information on the gellan gum synthesized by Sphingomonas paucimobilis with special emphasis on its fermentative production and downstream processing. Rheological behaviour of fermentation broth during fermentative production of gellan gum and problems associated with mass transfer have been addressed. Information on the biosynthetic pathway of gellan gum, enzymes and precursors involved in gellan gum production and application of metabolic engineering for enhancement of yield of gellan gum has been specified. Characteristics of gellan gum with respect to its structure, physicochemical properties, rheology of its solutions and gel formation behaviour are discussed. An attempt has also been made to review the current and potential applications of gellan gum in food, pharmaceutical and other industries.

  16. Increased gum arabic production after infestation of Acacia senegal ...

    African Journals Online (AJOL)

    The aim of this study was to investigate the correlation between the beetle Agrilus nubeculosus and gum arabic production by Acacia senegal. Some trees were tapped and left open to facilitate infestation by A. nubeculosus and others were covered with wire mesh as control. Gum yield, physical and chemical properties of ...

  17. Increased gum arabic production after infestation of Acacia senegal ...

    African Journals Online (AJOL)

    Jane

    2011-07-20

    Jul 20, 2011 ... Despite the fact that gum arabic is widely used as a vehicle for .... humidity, are the main factors affecting gum arabic yield. ... 450 mm from May to October; the soil is uniform deep reddish sand with little textural differentiation in the profile. .... 0.01; Mg/l * equivalent weight = mg/l (ppm); Molecular weight *.

  18. Design, formulation, and evaluation of ginger medicated chewing gum

    Directory of Open Access Journals (Sweden)

    Abolfazl Aslani

    2016-01-01

    Conclusion: Ginger chewing gum comprises admissible properties to be used as a modern drug delivery system due to its advantageous results in motion sickness. It passed all the specified tests for an acceptable chewing gum. Thus, it may be successfully produced to help GI problems.

  19. Gum acacia coating with garlic and cinnamon as an alternate ...

    African Journals Online (AJOL)

    Madhumita

    The antibacterial activity of gum arabic coating with ... Key words: Gum acacia coating, garlic, cinnamon, antioxidant, antimicrobial, meat, ... cinnamaldehyde and eugenol inhibit production of an ... antioxidant activity because these two properties are ... temperatures .... activity of these spices but no report on its application.

  20. Formulation and In vitro Evaluation of Natural Gum-Based ...

    African Journals Online (AJOL)

    obtained using the blends of natural gum: alginate at total polymer concentration of 2 % w/v using 10 % w/v calcium ... Keywords: Microbeads, Ibuprofen, Natural gums, Sodium alginate, Drug release kinetics. Tropical ... addition, its high cohesiveness which result in ... different chelating agents in order to optimize the.

  1. Seeds of genus Cassia as possible sources of industrial gums

    Energy Technology Data Exchange (ETDEWEB)

    Farooqi, M I.H.; Kapoor, V P; Islam, G

    1978-01-01

    Water-soluble mucilages (gums) and their properties were determined for the seeds of twenty Indian Cassia species, including nine trees and nine shrubs. The seeds of the shrub C. alata were regarded as the best potential commercial source of gums; those of the trees C. fistula, C. grandis, C. javanica, C. marginata and C. multijuga were also promising.

  2. Entandophragma angolense Gum as a Novel Binder and ...

    African Journals Online (AJOL)

    Michael

    the development of oral controlled release dosage forms. These semisynthetic polymers are quite expensive when compared with natural polymers such as guar gum and alginates, while the natural polymers are nontoxic and readily available [18]. The present study was designed to evaluate the hydrophilic natural gum ...

  3. Physicochemical characterization of starches from seven improved ...

    African Journals Online (AJOL)

    SARAH

    2014-01-31

    Jan 31, 2014 ... Key words: Cassava, starch, functional properties, industrial utilization. ... in demand for starch (Davis et al., 2002). Potato, maize, wheat and cassava are the major ... ambient temperature and stored at 4 °C for 4 weeks.

  4. Rheological and microstructural properties of Irradiated starch

    International Nuclear Information System (INIS)

    Atrous Turki, Hager

    2011-01-01

    Gamma irradiation ia s fast and efficient method to improve the functional properties of straches. Wheat and potato starches were submitted, in the present study, at 3,5,10 and 20 kGy radiation dose. The changes induced by irradiation on the rheological properties of these starches showed a decrease in the viscosity with increasing radiation dose. Chemicals bond's hydrolysis has been induced by free radicals that have been identified by EPR. Wheat starch presents five EPR signals after irradiation, whiles potato starch has a weak EPR signal. On the other hand, irradiation caused decrease in amylose content. This decrease is more pronounced in potato starch. Dry irradiated starch's MEB revealed no change in the shape, size and distribution of the granules. While, the observation of wheat starch allowed the complete disappearance of the granular structure and the dissolution of its macromolecules after irradiation which justifies the significant decrease in wheat starch's viscosity irradiated at 20 kGy.

  5. Deformation Mechanisms of Gum Metals Under Nanoindentation

    Science.gov (United States)

    Sankaran, Rohini Priya

    Gum Metal is a set of multi-component beta-Ti alloys designed and developed by Toyota Central R&D Labs in 2003 to have a nearly zero shear modulus in the direction. After significant amounts of cold-work (>90%), these alloys were found to have yield strengths at a significant fraction of the predicted ideal strengths and exhibited very little work hardening. It has been speculated that this mechanical behavior may be realized through an ideal shear mechanism as opposed to conventional plastic deformation mechanisms, such as slip, and that such a mechanism may be realized through a defect structure termed "nanodisturbance". It is furthermore theorized that for near ideal strength to be attained, dislocations need to be pinned at sufficiently high stresses. It is the search for these defects and pinning points that motivates the present study. However, the mechanism of plastic deformation and the true origin of specific defect structures unique to gum metals is still controversial, mainly due to the complexity of the beta-Ti alloy system and the heavily distorted lattice exhibited in cold worked gum metals, rendering interpretation of images difficult. Accordingly, the first aim of this study is to clarify the starting as-received microstructures of gum metal alloys through conventional transmission electron microscopy (TEM) and aberration-corrected high resolution scanning transmission electron microscopy with high-angle annular dark field detector (HAADF-HRSTEM) imaging. To elucidate the effects of beta-stability and starting microstructure on the deformation behavior of gum metals and thus to provide adequate context for potentially novel deformation structures, we investigate three alloy conditions: gum metal that has undergone solution heat treatment (STGM), gum metal that has been heavily cold worked (CWGM), and a solution treated alloy of nominal gum metal composition, but leaner in beta-stabilizing content (ST Ref-1). In order to directly relate observed

  6. Effect of starch isolation method on properties of sweet potato starch

    Directory of Open Access Journals (Sweden)

    A. SURENDRA BABU

    2014-08-01

    Full Text Available Isolation method of starch with different agents influences starch properties, which provide attention for studying the most appropriate method for isolation of starch. In the present study sweet potato starch was isolated by Sodium metabisulphate (M1, Sodium chloride (M2, and Distilled water (M3 methods and these were assessed for functional, chemical, pasting and structural properties. M3 yielded the greatest recovery of starch (10.20%. Isolation methods significantly changed swelling power and pasting properties but starches exhibited similar chemical properties. Sweet potato starches possessed C-type diffraction pattern. Small size granules of 2.90 μm were noticed in SEM of M3 starch. A high degree positive correlation was found between ash, amylose, and total starch content. The study concluded that isolation methods brought changes in yield, pasting and structural properties of sweet potato starch.

  7. Design, formulation and evaluation of nicotine chewing gum.

    Science.gov (United States)

    Aslani, Abolfazl; Rafiei, Sahar

    2012-01-01

    Nicotine replacement therapy (NRT) can help smokers to quit smoking. Nicotine chewing gum has attracted the attention from pharmaceutical industries to offer it to consumers as an easily accessible NRT product. However, the bitter taste of such gums may compromise their acceptability by patients. This study was, therefore, designed to develop 2 and 4 mg nicotine chewing gums of pleasant taste, which satisfy the consumers the most. Nicotine, sugar, liquid glucose, glycerin, different sweetening and taste-masking agents, and a flavoring agent were added to the gum bases at appropriate temperature. The medicated gums were cut into pieces of suitable size and coated by acacia aqueous solution (2% w/v), sugar dusting, followed by acacia-sugar-calcium carbonate until a smooth surface was produced. The gums' weight variation and content uniformity were determined. The release of nicotine was studied in pH 6.8 phosphate buffer using a mastication device which simulated the mastication of chewing gum in human. The Latin Square design was used for the evaluation of organoleptic characteristics of the formulations at different stages of development. Most formulations released 79-83% of their nicotine content within 20 min. Nicotine-containing sugar-coated gums in which aspartame as sweetener and cherry and eucalyptus as flavoring agents were incorporated (i.e. formulations F(19-SC) and F(20-SC), respectively) had optimal chewing hardness, adhering to teeth, and plumpness characteristics, as well as the most pleasant taste and highest acceptability to smokers. Taste enhancement of nicotine gums was achieved where formulations comprised aspartame as the sweetener and cherry and eucalyptus as the flavoring agents. Nicotine gums of pleasant taste may, therefore, be used as NRT to assist smokers quit smoking.

  8. Determination of locust bean gum and guar gum by polymerase chain reaction and restriction fragment length polymorphism analysis.

    Science.gov (United States)

    Meyer, K; Rosa, C; Hischenhuber, C; Meyer, R

    2001-01-01

    A polymerase chain reaction (PCR) was developed to differentiate the thickening agents locust bean gum (LBG) and the cheaper guar gum in finished food products. Universal primers for amplification of the intergenic spacer region between trnL 3' (UAA) exon and trnF (GAA) gene in the chloroplast (cp) genome and subsequent restriction analysis were applied to differentiate guar gum and LBG. The presence of guar gum powder added to LBG powder was detectable. Based on data obtained from sequencing this intergenic spacer region, a second PCR method for the specific detection of guar gum DNA was also developed. This assay detected guar gum powder in LBG in amounts as low as 1% (w/w). Both methods successfully detected guar gum and/or LBG in ice cream stabilizers and in foodstuffs, such as dairy products, ice cream, dry seasoning mixes, a finished roasting sauce, and a fruit jelly product, but not in products with highly degraded DNA, such as tomato ketchup and sterilized chocolate cream. Both methods detected guar gum and LBG in ice cream and fresh cheese at levels <0.1%.

  9. ( Phaseolus lunatus ) starch as a tablet disintegrant

    African Journals Online (AJOL)

    ) was evaluated. The starch from the seeds was extracted and its disintegrant ability was compared with that of maize starch BP in paracetamol based tablets at concentrations of 0, 2.5, 5, 7.5 and 10 %w/w. The following properties of the starch ...

  10. Kinetic modelling of enzymatic starch hydrolysis

    NARCIS (Netherlands)

    Bednarska, K.A.

    2015-01-01

    Kinetic modelling of enzymatic starch hydrolysis – a summary

    K.A. Bednarska

    The dissertation entitled ‘Kinetic modelling of enzymatic starch hydrolysis’ describes the enzymatic hydrolysis and kinetic modelling of liquefaction and saccharification of wheat starch.

  11. Sugarcane starch: quantitative determination and characterization

    Directory of Open Access Journals (Sweden)

    Joelise de Alencar Figueira

    2011-09-01

    Full Text Available Starch is found in sugarcane as a storage polysaccharide. Starch concentrations vary widely depending on the country, variety, developmental stage, and growth conditions. The purpose of this study was to determine the starch content in different varieties of sugarcane, between May and November 2007, and some characteristics of sugarcane starch such as structure and granules size; gelatinization temperature; starch solution filterability; and susceptibility to glucoamylase, pullulanase, and commercial bacterial and fungal α-amylase enzymes. Susceptibility to debranching amylolytic isoamylase enzyme from Flavobacterium sp. was also tested. Sugarcane starch had spherical shape with a diameter of 1-3 µm. Sugarcane starch formed complexes with iodine, which showed greater absorption in the range of 540 to 620 nm. Sugarcane starch showed higher susceptibility to glucoamylase compared to that of waxy maize, cassava, and potato starch. Sugarcane starch also showed susceptibility to debranching amylolytic pullulanases similar to that of waxy rice starch. It also showed susceptibility to α-amylase from Bacillus subtilis, Bacillus licheniformis, and Aspergillus oryzae similar to that of the other tested starches producing glucose, maltose, maltotriose, maltotetraose, maltopentose and limit α- dextrin.

  12. Properties of retrograded and acetylated starch produced via starch extrusion or starch hydrolysis with pullulanase.

    Science.gov (United States)

    Kapelko, M; Zięba, T; Gryszkin, A; Styczyńska, M; Wilczak, A

    2013-09-12

    The aim of the present study was to determine the impact of serial modifications of starch, including firstly starch extrusion or hydrolysis with pullulanase, followed by retrogradation (through freezing and defrosting of pastes) and acetylation (under industrial conditions), on its susceptibility to amylolysis. The method of production had a significant effect on properties of the resultant preparations, whilst the direction and extent of changes depended on the type of modification applied. In the produced starch esters, the degree of substitution, expressed by the per cent of acetylation, ranged from 3.1 to 4.4 g/100 g. The acetylation had a significant impact on contents of elements determined with the atomic emission spectrometry, as it contributed to an increased Na content and decreased contents of Ca and K. The DSC thermal characteristics enabled concluding that the modifications caused an increase in temperatures and a decrease in heat of transition (or its lack). The acetylation of retrograded starch preparations increased their solubility in water and water absorbability. The modifications were found to exert various effects on the rheological properties of pastes determined based on the Brabender's pasting characteristics and flow curves determined with the use of an oscillatory-rotating viscosimeter. All starch acetates produced were characterized by ca. 40% resistance to amylolysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Physicochemical properties of starches isolated from pumpkin compared with potato and corn starches.

    Science.gov (United States)

    Przetaczek-Rożnowska, Izabela

    2017-08-01

    The aim of the study was to characterize the selected physicochemical, thermal and rheological properties of pumpkin starches and compared with the properties of potato and corn starches used as control samples. Pumpkin starches could be used in the food industry as a free gluten starch. Better thermal and rheological properties could contribute to reduce the costs of food production. The syneresis of pumpkin starches was similar to that of potato starch but much lower than that for corn starch. Pasting temperatures of pumpkin starches were lower by 17-21.7°C and their final viscosities were over 1000cP higher than corn paste, but were close to the values obtained for potato starch. The thermodynamic characteristic showed that the transformation temperatures of pumpkin starches were lower than those measured for control starches. A level of retrogradation was much lower in pumpkin starch pastes (32-48%) than was in the case of corn (59%) or potato (77%) starches. The pumpkin starches gels were characterized by a much greater hardness, cohesiveness and chewiness, than potato or corn starches gels. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Occurrence of gum spots in black cherry after partial harvest cutting

    Science.gov (United States)

    Charles O. Rexrode; H. Clay Smith; H. Clay Smith

    1990-01-01

    Bark beetles, primarily the bark beetle Phlosotribus liminori (Harris), are the major cause of gum spots in sawtimber-size black cherry Prunus serotina Ehrh. Approximately 90 percent of all gum spots in the bole sections are caused by bark beetles. Gum spots were studied in 95 black cherry trees near Parsons, West Virginia. Over 50 percent of the bark beetle-caused gum...

  15. Flavor-Enhanced Modulation of Cerebral Blood Flow during Gum Chewing.

    Directory of Open Access Journals (Sweden)

    Yoko Hasegawa

    Full Text Available Flavor perception, the integration of taste and odor, is a critical factor in eating behavior. It remains unclear how such sensory signals influence the human brain systems that execute the eating behavior.WE TESTED CEREBRAL BLOOD FLOW (CBF IN THE FRONTAL LOBES BILATERALLY WHILE SUBJECTS CHEWED THREE TYPES OF GUM WITH DIFFERENT COMBINATIONS OF TASTE AND ODOR: no taste/no odor gum (C-gum, sweet taste/no odor gum (T-gum, and sweet taste/lemon odor gum (TO-gum. Simultaneous recordings of transcranial Doppler ultrasound (TCD and near infrared spectrometer (NIRS were used to measure CBF during gum chewing in 25 healthy volunteers. Bilateral masseter muscle activity was also monitored.We found that subjects could discriminate the type of gum without prior information. Subjects rated the TO-gum as the most flavorful gum and the C-gum as the least flavorful. Analysis of masseter muscle activity indicated that masticatory motor output during gum chewing was not affected by taste and odor. The TCD/NIRS measurements revealed significantly higher hemodynamic signals when subjects chewed the TO-gum compared to when they chewed the C-gum and T-gum.These data suggest that taste and odor can influence brain activation during chewing in sensory, cognitive, and motivational processes rather than in motor control.

  16. Chew on this: No support for facilitating effects of gum on spatial task performance.

    Science.gov (United States)

    Nader, Ingo W; Gittler, Georg; Waldherr, Karin; Pietschnig, Jakob

    2010-09-01

    To determine whether chewing of gum facilitates spatial task performance in healthy participants, two behavioral experiments were performed. In the first experiment, spatial task performance of 349 men and women preceding and after treatment administration (saccharated chewing gum, sugar-free chewing gum, no chewing gum) was assessed using effect modeling by means of Item Response Theory. In the second experiment, another 100 participants were either administered sugar-free chewing gum or no chewing gum during spatial task performance. Effects of gum in the second study were assessed by standard means of data analysis. Results indicated no significant effects of either chewing gum or sugar on spatial task performance in either experiment. Our findings are consistent with recent studies investigating the influences of chewing gum on various memory functions, extending them by another measure of cognitive ability. Thus, further doubt is cast on enhancing effects of chewing gum on cognitive task performance. Copyright 2010 Elsevier Ltd. All rights reserved.

  17. Masticatory performance alters stress relief effect of gum chewing.

    Science.gov (United States)

    Nishigawa, Keisuke; Suzuki, Yoshitaka; Matsuka, Yoshizo

    2015-10-01

    We evaluated the effects of gum chewing on the response to psychological stress induced by a calculation task and investigated the relationship between this response and masticatory performance. Nineteen healthy adult volunteers without dental problems undertook the Uchida-Kraepelin (UK) test (30 min of reiterating additions of one-digit numbers). Before and immediately after the test, saliva samples were collected from the sublingual area of the participants. Three min after the UK test, the participants were made to chew flavorless gum for 3 min, and the final saliva samples were collected 10 min after the UK test. The experiment was performed without gum chewing on a different day. Masticatory performance was evaluated using color-changing chewing gum. Salivary CgA levels at immediately and 10 min after the UK test were compared with and without gum chewing condition. Two-way repeated measures analysis of variance revealed significant interaction between gum chewing condition and changes in CgA levels during post 10 min UK test period. A significant correlation was found between changes in CgA levels and masticatory performance in all participants. Our results indicate that gum chewing may relieve stress responses; however, high masticatory performance is required to achieve this effect. Copyright © 2015 Japan Prosthodontic Society. Published by Elsevier Ltd. All rights reserved.

  18. Maize starch biphasic pasting curves

    CSIR Research Space (South Africa)

    Nelles, EM

    2000-05-01

    Full Text Available (150–500 rev/min). The second pasting peak is attributed to the formation of complexes between amylose and low levels of lipid present in maize starch. When lipid was partially removed by extraction with methanol-chloroform (1: 3 v/v), the second...

  19. Resistant starch: promise for improving human health.

    Science.gov (United States)

    Birt, Diane F; Boylston, Terri; Hendrich, Suzanne; Jane, Jay-Lin; Hollis, James; Li, Li; McClelland, John; Moore, Samuel; Phillips, Gregory J; Rowling, Matthew; Schalinske, Kevin; Scott, M Paul; Whitley, Elizabeth M

    2013-11-01

    Ongoing research to develop digestion-resistant starch for human health promotion integrates the disciplines of starch chemistry, agronomy, analytical chemistry, food science, nutrition, pathology, and microbiology. The objectives of this research include identifying components of starch structure that confer digestion resistance, developing novel plants and starches, and modifying foods to incorporate these starches. Furthermore, recent and ongoing studies address the impact of digestion-resistant starches on the prevention and control of chronic human diseases, including diabetes, colon cancer, and obesity. This review provides a transdisciplinary overview of this field, including a description of types of resistant starches; factors in plants that affect digestion resistance; methods for starch analysis; challenges in developing food products with resistant starches; mammalian intestinal and gut bacterial metabolism; potential effects on gut microbiota; and impacts and mechanisms for the prevention and control of colon cancer, diabetes, and obesity. Although this has been an active area of research and considerable progress has been made, many questions regarding how to best use digestion-resistant starches in human diets for disease prevention must be answered before the full potential of resistant starches can be realized.

  20. Effects of caffeine in chewing gum on mood and attention.

    Science.gov (United States)

    Smith, Andrew

    2009-04-01

    Recent research has shown that even small doses (attention tasks. Previous studies have given the caffeine in a variety of beverages or in capsules and it was of interest to see whether similar effects could be observed when the caffeine was given in gum. In addition, chewing gum has been shown to have behavioural effects and the present study extended our knowledge of this topic. To compare the effects of caffeinated gum (40 mg), placebo gum and no gum conditions on mood and attention. A double blind placebo controlled study was conducted with volunteers being randomly assigned to one of the three conditions. Baseline measures of mood and attention were taken prior to chewing and a test session was then conducted. One hundred and eighteen young adults participated in the study. Caffeinated gum was associated with a more positive mood and better performance on tasks requiring sustained attention. The caffeine improved the speed of encoding of new information which is consistent with previous findings. Chewing placebo gum was also found to be associated with more positive mood, both shortly after chewing and at the end of the study. The implications of the present study are that chewing caffeinated gum has been shown to improve performance efficiency and mood by its alerting and energising effects. The profile of caffeine effects is what one would predict from the existing caffeine literature and such effects may be extremely beneficial in real-life situations. Prior chewing of placebo gum was associated with a more positive mood and this also confirms previous findings.

  1. Preparation, characterization and utilization of starch nanoparticles.

    Science.gov (United States)

    Kim, Hee-Young; Park, Sung Soo; Lim, Seung-Taik

    2015-02-01

    Starch is one of the most abundant biopolymers in nature and is typically isolated from plants in the form of micro-scale granules. Recent studies reported that nano-scale starch particles could be readily prepared from starch granules, which have unique physical properties. Because starch is environmentally friendly, starch nanoparticles are suggested as one of the promising biomaterials for novel utilization in foods, cosmetics, medicines as well as various composites. An overview of the most up-to-date information regarding the starch nanoparticles including the preparation processes and physicochemical characterization will be presented in this review. Additionally, the prospects and outlooks for the industrial utilization of starch nanoparticles will be discussed. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. Cassava starch in the Brazilian food industry

    Directory of Open Access Journals (Sweden)

    Ivo Mottin Demiate

    2011-06-01

    Full Text Available Cassava starch is a valued raw material for producing many kinds of modified starches for food applications. Its physicochemical properties, as well as its availability, have made it an interesting and challenging ingredient for the food industry. In the present work, food grade modified cassava starches were purchased from producers and analyzed for selected physicochemical characteristics. Samples of sour cassava starch were included, as well as one sample of native cassava starch. Results showed that almost all modified starches were resistant to syneresis, produced pastes more stable to stirred cooking, and some of them were difficult to cook. The sour cassava starches presented high acidity and resulted in clear and unstable pastes during stirred cooking, susceptible to syneresis.

  3. Evidence against memorial facilitation and context-dependent memory effects through the chewing of gum

    OpenAIRE

    Johnson, A.J.; Miles, C.

    2007-01-01

    The experiment examined the prediction that chewing gum at learning and/or recall facilitated subsequent word recall. Chewing gum at learning significantly impaired recall, indicating that the chewing of gum has a detrimental impact upon initial word encoding. In addition, a context-dependent memory effect was reported for those participants who both learned and recalled in the absence of gum, however a context dependent effect was not found with chewing gum. The findings contradict previous ...

  4. Evidence against memorial facilitation and context-dependent memory effects through the chewing of gum.

    Science.gov (United States)

    Johnson, Andrew J; Miles, Christopher

    2007-05-01

    The experiment examined the prediction that chewing gum at learning and/or recall facilitated subsequent word recall. Chewing gum at learning significantly impaired recall, indicating that the chewing of gum has a detrimental impact upon initial word encoding. In addition, a context-dependent memory effect was reported for those participants who both learned and recalled in the absence of gum; however, a context-dependent effect was not found with chewing gum. The findings contradict previous research.

  5. Mechanical, barrier and morphological properties of starch nanocrystals-reinforced pea starch films.

    Science.gov (United States)

    Li, Xiaojing; Qiu, Chao; Ji, Na; Sun, Cuixia; Xiong, Liu; Sun, Qingjie

    2015-05-05

    To characterize the pea starch films reinforced with waxy maize starch nanocrystals, the mechanical, water vapor barrier and morphological properties of the composite films were investigated. The addition of starch nanocrystals increased the tensile strength of the composite films, and the value of tensile strength of the composite films was highest when starch nanocrystals content was 5% (w/w). The moisture content (%), water vapor permeability, and water-vapor transmission rate of the composite films significantly decreased as starch nanocrystals content increased. When their starch nanocrystals content was 1-5%, the starch nanocrystals dispersed homogeneously in the composite films, resulting in a relatively smooth and compact film surface and better thermal stability. However, when starch nanocrystals content was more than 7%, the starch nanocrystals began to aggregate, which resulted in the surface of the composite films developing a longitudinal fibrous structure. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. Physicochemical properties of starches and proteins in alkali-treated mungbean and cassava starch granules.

    Science.gov (United States)

    Israkarn, Kamolwan; Na Nakornpanom, Nantarat; Hongsprabhas, Parichat

    2014-05-25

    This study explored the influences of envelope integrity of cooked starch granules on physicochemical and thermophysical properties of mungbean and cassava starches. Alkali treatment was used to selectively leach amylose from the amorphous region of both starches and partially fragmented starch molecules into lower-molecular-weight polymers. It was found that despite the loss of 40% of the original content of amylose, both mungbean and cassava starches retained similar crystallinities, gelatinization temperature ranges, and pasting profiles compared to the native starches. However, the loss of granule-bound starch synthases during alkali treatment and subsequent alkali cooking in excess water played significant roles in determining granular disintegration. The alterations in envelope integrity due to the negative charge repulsion among polymers within the envelope of swollen granules, and the fragmentation of starch molecules, were responsible for the alterations in thermophysical properties of mungbean and cassava starches cooked under alkaline conditions. Copyright © 2014 Elsevier Ltd. All rights reserved.

  7. Mechanical properties and solubility in water of corn starch-collagen composite films: Effect of starch type and concentrations.

    Science.gov (United States)

    Wang, Kun; Wang, Wenhang; Ye, Ran; Liu, Anjun; Xiao, Jingdong; Liu, Yaowei; Zhao, Yana

    2017-02-01

    This study investigated the possibility of enhancing the properties of collagen with three different maize starches: waxy maize starch, normal starch, and high amylose starch. Scanning electron microscopy images revealed that starch-collagen films had a rougher surface compared to pure collagen films which became smoother upon heating. Amylose starch and normal starch increased the tensile strength of unheated collagen films in both dry and wet states, while all starches increased tensile strength of collagen film by heating. Depending upon the amylose content and starch concentrations, film solubility in water decreased with the addition of starch. DSC thermograms demonstrated that addition of all starches improved the thermal stability of the collagen film. Moreover, X-ray diffraction results indicated that except for high amylose starch, the crystallinity of both starch and collagen was significantly decreased when subject to heating. FTIR spectra indicated that intermolecular interactions between starch and collagen were enhanced upon heating. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. ENZYME RESISTANCE OF GENETICALLY MODIFIED STARCH POTATOES

    Directory of Open Access Journals (Sweden)

    A. Sh. Mannapova

    2015-01-01

    Full Text Available Here in this article the justification of expediency of enzyme resistant starch use in therapeutic food products is presented . Enzyme resistant starch is capable to resist to enzymatic hydrolysis in a small intestine of a person, has a low glycemic index, leads to decrease of postprandial concentration of glucose, cholesterol, triglycerides in blood and insulin reaction, to improvement of sensitivity of all organism to insulin, to increase in sense of fulness and to reduction of adjournment of fats. Resistant starch makes bifidogenшс impact on microflora of a intestine of the person, leads to increase of a quantity of lactobacillus and bifidobacterium and to increased production of butyric acid in a large intestine. In this regard the enzyme resistant starch is an important component in food for prevention and curing of human diseases such as diabetes, obesity, colitis, a cancer of large and direct intestine. One method is specified by authors for imitation of starch digestion in a human body. This method is based on the definition of an enzyme resistance of starch in vitro by its hydrolysis to glucose with application of a glucoamylase and digestive enzyme preparation Pancreatin. This method is used in researches of an enzyme resistance of starch, of genetically modified potato, high amylose corn starch Hi-Maize 1043 and HYLON VII (National Starch Food Innovation, USA, amylopectin and amylose. It is shown that the enzyme resistance of the starch emitted from genetically modified potatoes conforms to the enzyme resistance of the high amylose corn starch “Hi-Maize 1043 and HYLON VII starch”, (National Starch Food Innovation, the USA relating to the II type of enzyme resistant starch. It is established that amylopectin doesn't have the enzyme resistant properties. The results of researches are presented. They allow us to make the following conclusion: amylose in comparison with amylopectin possesses higher enzyme resistance and gives to

  9. Barley grain constituents, starch composition, and structure affect starch in vitro enzymatic hydrolysis.

    Science.gov (United States)

    Asare, Eric K; Jaiswal, Sarita; Maley, Jason; Båga, Monica; Sammynaiken, Ramaswami; Rossnagel, Brian G; Chibbar, Ravindra N

    2011-05-11

    The relationship between starch physical properties and enzymatic hydrolysis was determined using ten different hulless barley genotypes with variable carbohydrate composition. The ten barley genotypes included one normal starch (CDC McGwire), three increased amylose starches (SH99250, SH99073, and SB94893), and six waxy starches (CDC Alamo, CDC Fibar, CDC Candle, Waxy Betzes, CDC Rattan, and SB94912). Total starch concentration positively influenced thousand grain weight (TGW) (r(2) = 0.70, p starch concentration (r(2) = -0.80, p hydrolysis of pure starch (r(2) = -0.67, p starch concentration (r(2) = 0.46, p starch (RS) in meal and pure starch samples. The rate of starch hydrolysis was high in pure starch samples as compared to meal samples. Enzymatic hydrolysis rate both in meal and pure starch samples followed the order waxy > normal > increased amylose. Rapidly digestible starch (RDS) increased with a decrease in amylose concentration. Atomic force microscopy (AFM) analysis revealed a higher polydispersity index of amylose in CDC McGwire and increased amylose genotypes which could contribute to their reduced enzymatic hydrolysis, compared to waxy starch genotypes. Increased β-glucan and dietary fiber concentration also reduced the enzymatic hydrolysis of meal samples. An average linkage cluster analysis dendrogram revealed that variation in amylose concentration significantly (p starch concentration in meal and pure starch samples. RS is also associated with B-type granules (5-15 μm) and the amylopectin F-III (19-36 DP) fraction. In conclusion, the results suggest that barley genotype SH99250 with less decrease in grain weight in comparison to that of other increased amylose genotypes (SH99073 and SH94893) could be a promising genotype to develop cultivars with increased amylose grain starch without compromising grain weight and yield.

  10. In vitro tooth whitening effect of two medicated chewing gums compared to a whitening gum and saliva

    Directory of Open Access Journals (Sweden)

    Saroea Geoffrey

    2008-08-01

    Full Text Available Abstract Background Extrinsic staining of teeth may result from the deposition of a variety of pigments into or onto the tooth surface, which originate mainly from diet or from tobacco use. More recently, clinical studies have demonstrated the efficacy of some chewing gums in removing extrinsic tooth staining. The aim of this study was to assess the effectiveness of two nicotine medicated chewing gums (A and B on stain removal in an in vitro experiment, when compared with a confectionary whitening chewing gum (C and human saliva (D. Methods Bovine incisors were stained by alternating air exposure and immersion in a broth containing natural pigments such as coffee, tea and oral microorganisms for 10 days. Stained enamel samples were exposed to saliva alone or to the test chewing gums under conditions simulating human mastication. The coloration change of the enamel samples was measured using a spectrophotometer. Measurements were obtained for each specimen (average of three absorbances using the L*a*b scale: lightness (L*, red-green (a and yellow-blue (b. Results Medicated chewing gums (A and B removed a greater amount of visible extrinsic stain, while the confectionary chewing gum with a whitening claim (C had a milder whitening effect as evaluated by quantitative and qualitative assessment. Conclusion The tested Nicotine Replacement Therapy (NRT chewing gums were more effective in the removal of the extrinsic tooth stain. This visible improvement in tooth whitening appearance could strengthen the smokers' motivation to quit smoking.

  11. What do GUM physicians think should be taught in a modern undergraduate GUM module? A qualitative inquiry.

    Science.gov (United States)

    Fernando, I

    2015-10-01

    Traditional undergraduate Genitourinary Medicine (GUM) teaching in the UK concentrated on the management of individual sexually transmitted infections. There is significant variation, however, in the GUM teaching provided by different medical schools today. I undertook a qualitative interview study to gather views of GUM and other sexual health clinicians regarding what should be taught within a modern undergraduate GUM module. Nine GUM clinicians and two Sexual and Reproductive Health (SRH) clinicians participated in the study; all were directly involved in undergraduate teaching. Semi-structured interviews were conducted with study participants by a single interviewer, focusing on three key topics: their individual opinions regarding important learning outcomes (LOs) for a modern model GUM curriculum, their preferred teaching methods and the total recommended teaching time required. Interviews were audio-recorded with consent and professionally transcribed. Data were analysed by the content analysis method. Interviewees frequently stressed skill and attitudinal LOs, even above knowledge. Recommended important skills included sexual history taking, HIV risk assessment and testing, and male and female genital examination. Recommended attitudinal LOs were developing an open and non-judgemental approach to sexual health issues and understanding sexual well-being to be an important component of general health. Respondents were keen for a mixture of teaching methods, but generally agreed that clinic attendance and experiential learning were beneficial. They preferred that GUM teaching should be delivered in the latter years of the undergraduate curriculum. © The Author(s) 2015.

  12. Xylitol chewing gum and dental caries.

    Science.gov (United States)

    Tanzer, J M

    1995-02-01

    There is an extensive peer-reviewed literature on xylitol chewing gum as it pertains to effects on tooth decay in human subjects, on human dental plaque reduction, on inhibition of dental plaque acid production, on inhibition of the growth and metabolism of the mutans group of streptococci which are the prime causative agents of tooth decay, on reduction of tooth decay in experimental animals, and on xylitol's reported contribution to the remineralisation of teeth. The literature not only supports the conclusion that xylitol is non-cariogenic but it is now strongly suggestive that xylitol is caries inhibitory, that is, anti-cariogenic in human subjects, and it supplies reasonable mechanistic explanation(s).

  13. A REVIEW ON BIODEGRADABLE STARCH BASED FILM

    Directory of Open Access Journals (Sweden)

    Hooman Molavi

    2015-04-01

    Full Text Available In recent years, biodegradable edible films have become very important in research related to food, due to their compatibility with the environment and their use in the food packaging industry. Various sources can be used in the production of biopolymers as biodegradable films that include polysaccharides, proteins and lipids. Among the various polysaccharides, starch due to its low price and its abundance in nature is of significant importance. Several factors affect the properties of starch films; such as the source which starch is obtained from, as well as the ratio of constituents of the starch. Starch films have advantages such as low thickness, flexibility and transparency though; there are some downsides to mention, such as the poor mechanical properties and water vapor permeability. Thus, using starch alone to produce the film will led to restrictions on its use. To improve the mechanical properties of starch films and also increases resistance against humidity, several methods can be used; including the starch modifying techniques such as cross linking of starch and combining starch with other natural polymers. Other methods such as the use of lipid in formulations of films to increase the resistance to moisture are possible, but lipids are susceptible to oxidation. Therefore, new approaches are based on the integration of different biopolymers in food packaging.

  14. Physicochemical and functional parameters of Cochlospermum vitifolium (bototo gum exudate

    Directory of Open Access Journals (Sweden)

    Maritza Coromoto Martínez

    2016-12-01

    Full Text Available The physicochemical parameters of Cochlospermum vitifolium they were evaluated and were linked to certain functional properties of industrial interest. The physicochemical parameters were determined by the classic methodology used for carbohydrates and the functional properties, as reported in the literature. The results obtained showed that the gum object of this study is low soluble in water, which corresponds with relatively high values of swelling indexes and water absorption capacity. Also, the intrinsic viscosity of the C. vitifolium exudate was related to a high molar mass, in the order of 106. Its emulsifying capacity is high, which is attributed to hydrophobic groups present in its structure. The gum gels at a minimum concentration, similar to that of the gum karaya (4.5%, but the gel that forms agglomerates, it is not uniform. The C. vitifolium gum exhibits important physicochemical and functional parameters which could serve as a criterion for testing its use in various industries.

  15. Studies on some Physicochemical Properties of the Plant Gum ...

    African Journals Online (AJOL)

    A. senegal, A. sieberiana and A. nilotica) in Batagarawa, Katsina State, were determined and compared. Data generated from the study confirm that there are a number of physicochemical differences between the gum exudates.

  16. {sup 13} C-NMR of mesquite gum

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Cristina T; Garcia, Rosangela B [Universidade Federal, Rio de Janeiro, RJ (Brazil). Inst. de Macromoleculas

    1992-12-31

    Mesquite and guar gums are galactomannans extracted from the seeds of Proposis Juliflora and Cyamopsis tetragonolobus, respectively. An experimental sample of mesquite gum and a commercial sample of guar gum were partially depolymerized by ultrasonic radiation and the produce analysed by high resolution {sup 13} C-NMR spectroscopy. The different carbon lines were resolved and their assignments were done as those reported in the literature. The galactose to mannose ratios (G/M) were estimated from the relative peak areas of the C-1 lines as G/M=61 for mesquite and G/M=0.54 for guar gum. The next nearest-neighbour probabilities (diad frequencies) of the D-galactosyl substitution to the D-mannose backbone were evaluated by integrating C-4 mannose splitted peaks. (author) 9 refs., 2 figs., 2 tabs.

  17. Germination Response of Gum Arabic (Acacia senegal L.) Seeds to ...

    African Journals Online (AJOL)

    ... Arabic (Acacia senegal L.) Seeds to Hot Water Pre-Treatment in Maiduguri, ... of Maiduguri under tree shade, to study the effect of hot water pre-treatment duration. ... Germination response, pre-sowing treatment, gum Arabic, orthodox seeds.

  18. Evaluation of mucoadhesive potential of gum cordia, an anionic polysaccharide.

    Science.gov (United States)

    Ahuja, Munish; Kumar, Suresh; Kumar, Ashok

    2013-04-01

    The study involves mucoadhesive evaluation by formulating buccal discs using fluconazole as the model drug. The effect of compression pressure and gum cordia/lactose ratio on the ex vivo bioadhesion time and in vitro release of fluconazole was optimized using central composite experimental design. It was observed that the response ex vivo bioadhesion time was affected significantly by the proportion of gum cordia in the buccal discs while the in vitro release of fluconazole from the buccal discs was influenced significantly by the compression pressure. The optimized batch of buccal discs comprised of gum cordia/lactose - 0.66, fluconazole - 20 mg and was compressed at the pressure of 6600 kg. Further, it provided the ex vivo bioadhesion of 22 h and in vitro release of 80% in 24h. In conclusion, gum cordia is a promising bucoadhesive polymer. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Microbial production of raw starch digesting enzymes | Sun | African ...

    African Journals Online (AJOL)

    Raw starch digesting enzymes refer to enzymes that can act directly on raw starch granules below the gelatinization temperature of starch. With the view of energy-saving, a worldwide interest has been focused on raw starch digesting enzymes in recent years, especially since the oil crisis of 1973. Raw starch digesting ...

  20. Xylitol Chewing Gums on the Market: Do They Prevent Caries?

    Science.gov (United States)

    Alanzi, Abrar; Soderling, Eva; Varghese, Anisha; Honkala, Eino

    To measure the xylitol content in sugar-free chewing gums available on the market in Gulf Cooperation Council (GCC) countries in the Middle East, in order to identify those products that can provide the recommended daily dose of xylitol for caries prevention (6-7 g). Acid production from chewing gums was also measured in vitro and in vivo. Twenty-one chewing gums containing xylitol were identified and collected from the GCC market (Kuwait, Bahrain, Qatar, Saudi Arabia, UAE and Oman). Xylitol was extracted and its concentration was analysed using a special enzymatic kit. The pH of extracts was measured during 30-min incubation with Streptococcus mutans. Changes in saliva and plaque pH were noted in four subjects after the consumption of highly concentrated xylitol gums. The xylitol content in grams was clearly mentioned only on one product's label. Twelve products stated the percentage of xylitol (3.5% to 35%). The rest did not specify the amount. The mean measured weight of one piece of gum was 1.67 ± 0.38 g. The mean measured xylitol content/piece was 0.33 ± 0.21 g. Xylitol content was 0.5 g in 5 products. None of the highly concentrated xylitol gums showed a pH drop in vitro or in vivo. One chewing gum, containing xylitol and glucose, resulted in a low pH level (xylitol chewing gums sold on the GCC market do not provide the consumers with the recommended daily dose of xylitol for caries prevention. Clear, accurate labeling is recommended.

  1. The next GUM and its proposals: a comparison study

    Science.gov (United States)

    Damasceno, J. C.; Couto, P. R. G.

    2018-03-01

    The Guide to the Expression of Uncertainty in Measurement (GUM) is currently under revision. New proposals for its implementation were circulated in the form of a draft document. Two of the main changes are explored in this work using a Brinell hardness model example. Changes in the evaluation of uncertainty for repeated indications and in the construction of coverage intervals are compared with the classic GUM and with Monte Carlo simulation method.

  2. Natural polymers, gums and mucilages as excipients in drug delivery.

    Science.gov (United States)

    Kumar, Shobhit; Gupta, Satish Kumar

    2012-01-01

    Use of natural polymers, gums and mucilages in drug delivery systems has been weighed down by the synthetic materials. Natural based excipients offered advantages such as non-toxicity, less cost and abundantly availablity. Aqueous solubility of natural excipients plays an important role in their selection for designing immediate, controlled or sustained release formulations. This review article provide an overview of natural gum, polymers and mucilages as excipients in dosage forms as well as novel drug delivery systems.

  3. Extraction and characterization of artocarpus integer gum as pharmaceutical excipient.

    Science.gov (United States)

    Farooq, Uzma; Malviya, Rishabha; Sharma, Pramod Kumar

    2014-01-01

    Natural polymers are widely used as excipients in pharmaceutical formulations. They are easily available, cheap and less toxic as compared to synthetic polymers. This study involves the extraction and characterization of kathal (Artocarpus integer) gum as a pharmaceutical excipient. Water was used as a solvent for extraction of the natural polymer. Yield was calculated with an aim to evaluate the efficacy of the process. The product was screened for the presence of Micrometric properties, and swelling index, flow behavior, surface tension, and viscosity of natural polymers were calculated. Using a water based extraction method, the yield of gum was found to be 2.85%. Various parameters such as flow behavior, organoleptic properties, surface tension, viscosity, loss on drying, ash value and swelling index together with microscopic studies of particles were done to characterize the extracted gum. The result showed that extracted kathal gum exhibited excellent flow properties. The gum was investigated for purity by carrying out chemical tests for different phytochemical constituents and only carbohydrates were found to be present. It had a good swelling index (13 ± 1). The pH and surface tension of the 1% gum solution were found to be 6 ± 0.5 and 0.0627 J/m2, respectively. The ash values such as total ash, acid insoluble ash, and water soluble ash were found to be 18.9%, 0.67% and 4% respectively. Loss on drying was 6.61%. The extracted gum was soluble in warm water and insoluble in organic solvents. The scanning electron micrograph (SEM) revealed rough and irregular particles of the isolated polymer. The results of the evaluated properties showed that kathal-derived gum has acceptable pH and organoleptic properties and can be used as a pharmaceutical excipient to formulate solid oral dosage forms.

  4. Characterization of Grewia Gum, a Potential Pharmaceutical Excipient

    Directory of Open Access Journals (Sweden)

    Elijah.I.Nep

    2010-03-01

    Full Text Available Grewia gum was extracted from the inner stem bark of Grewia mollis and characterized by several techniques such as gas chromatography (GC, gel permeation chromatography (GPC, scanning electron microscopy (SEM, differential scanning calorimetry (DSC and thermogravimetric analysis of the extracted sample. Spectroscopic techniques such as x-ray photoelectron spectroscopy (XPS, fourier-transformed infrared (FT-IR, solid-state nuclear magnetic resonance (NMR, and 1H and 13C NMR techniques were also used to characterize the gum. The results showed that grewia gum is a typically amorphous polysaccharide gum containing glucose, rhamnose, galactose, arabinose and xylose as neutral sugars. It has an average molecular weight of 5925 kDa expressed as the pullulan equivalent. The gum slowly hydrated in water, dispersing and swelling to form a highly viscous dispersion exhibiting pseudoplastic flow behaviour. The polysaccharide gum is thermally stable and may have application as stabilizer or suspending agent in foods, cosmetics and in pharmaceuticals. It may have application as a binder or sustained-release polymer matrix in tablets or granulations.

  5. Evaluation of carboxymethyl moringa gum as nanometric carrier.

    Science.gov (United States)

    Rimpy; Abhishek; Ahuja, Munish

    2017-10-15

    In the present study, carboxymethylation of Moringa oleifera gum was carried out by reacting with monochloroacetic acid. Modified gum was characterised employing Fourier-transform infrared spectroscopy, differential scanning calorimetry, X-ray diffraction, scanning electron microscopy, and Rheology study. The carboxymethyl modification of moringa gum was found to increase its degree of crystallinity, reduce viscosity and swelling, increase the surface roughness and render its more anionic. The interaction between carboxymethyl moringa gum and chitosan was optimised by 2-factor, 3-level central composite experimental design to prepare polyelectrolyte nanoparticle using ofloxacin, as a model drug. The optimal calculated parameters were found to be carboxymethyl moringa gum- 0.016% (w/v), chitosan- 0.012% (w/v) which provided polyelectrolyte nanoparticle of average particle size 231nm and zeta potential 28mV. Carboxymethyl moringa gum-chitosan polyelectrolyte nanoparticles show sustained in vitro release of ofloxacin upto 6h which followed first order kinetics with mechanism of release being erosion of polymer matrix. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. GumTree-An integrated scientific experiment environment

    International Nuclear Information System (INIS)

    Lam, Tony; Hauser, Nick; Goetz, Andy; Hathaway, Paul; Franceschini, Fredi; Rayner, Hugh; Zhang, Lidia

    2006-01-01

    GumTree is an open source and multi-platform graphical user interface for performing neutron scattering and X-ray experiments. It handles the complete experiment life cycle from instrument calibration, data acquisition, and real time data analysis to results publication. The aim of the GumTree Project is to create a highly Integrated Scientific Experiment Environment (ISEE), allowing interconnectivity and data sharing between different distributed components such as motors, detectors, user proposal database and data analysis server. GumTree is being adapted to several instrument control server systems such as TANGO, EPICS and SICS, providing an easy-to-use front-end for users and simple-to-extend model for software developers. The design of GumTree is aimed to be reusable and configurable for any scientific instrument. GumTree will be adapted to six neutron beam instruments for the OPAL reactor at ANSTO. Other European institutes including ESRF, ILL and PSI have shown interest in using GumTree as their workbench for instrument control and data analysis

  7. Fabrication and characterization of gum Arabic bonded Rhizophora spp. particleboards

    International Nuclear Information System (INIS)

    Abuarra, Ali; Hashim, Rokiah; Bauk, Sabar; Kandaiya, Sivamany; Tousi, Ehsan Taghizadeh

    2014-01-01

    Highlights: • Exploring gum Arabic as a binder for Rhizophora sp. particleboards. • The addition of gum Arabic improved overall properties. • Gum Arabic could be added to manufacture particleboards. - Abstract: Gum Arabic (GA) was used as a binder for the fabrication of Rhizophora spp. particleboards. The physical and mechanical properties of the bioadhesive bonded particleboards, including moisture content, internal bond (IB) strength, thickness swelling (TS), water absorption (WA) and field-emission scanning electron microscopy (FESEM) were used to characterize the manufactured particleboards. Three different particle sizes of the Rhizophora spp. with four adhesive levels were utilized. Results revealed that the addition of GA into the particleboards noticeably improved panel overall properties. The GA bonded particleboards resulted in smoother surfaces, more rigid texture and better internal bonding strength compared to binderless particleboards made without using any adhesive. All specimens had internal bond strength of more than the minimum requirement of the Japanese Industrial Standard JIS A-5908 Type-8 of 0.15 N/mm 2 and were noticed to increase by increasing the adhesive level. However the GA bonded particleboards had higher percentage of WA and the TS compared with the binderless boards. Microscopic study also revealed that particleboards bonded with the gum had better contact compared to the binderless boards. Based on these results, it could be concluded that gum Arabic is an effective natural substance that could be added to manufacture particleboards to improve some of panels’ physical and mechanical properties

  8. Oxidized Xanthan Gum and Chitosan as Natural Adhesives for Cork

    Directory of Open Access Journals (Sweden)

    Diana Paiva

    2016-07-01

    Full Text Available Natural cork stopper manufacturing produces a significant amount of cork waste, which is granulated and combined with synthetic glues for use in a wide range of applications. There is a high demand for using biosourced polymers in these composite materials. In this study, xanthan gum (XG and chitosan (CS were investigated as possible natural binders for cork. Xanthan gum was oxidized at two different aldehyde contents as a strategy to improve its water resistance. This modification was studied in detail by 1H and 13C nuclear magnetic resonance (NMR, and the degree of oxidation was determined by the hydroxylamine hydrochloride titration method. The performance of the adhesives was studied by tensile tests and total soluble matter (TSM determinations. Xanthan gum showed no water resistance, contrary to oxidized xanthan gum and chitosan. It is hypothesized that the good performance of oxidized xanthan gum is due to the reaction of aldehyde groups—formed in the oxidation process—with hydroxyl groups on the cork surface during the high temperature drying. Combining oxidized xanthan gum with chitosan did not yield significant improvements.

  9. GumTree - An Integrated Scientific Experiment Environment

    International Nuclear Information System (INIS)

    Lam, Tony; Hauser, Nick; Hathaway, Paul; Franceschini, Fredi; Rayner, Hugh; Zhang, Lidia; Goetz, Andy

    2005-01-01

    Full text: GumTree is an open source and multi-platform graphical user interface for performing neutron scattering and X-ray experiments. It handles the complete experiment life cycle from instrument calibration, data acquisition, and real time data analysis to results publication. The aim of the GumTree Project is to create a highly Integrated Scientific Experiment Environment (ISEE), allowing interconnectivity and data sharing between different distributed components such as motors, detectors, user proposal database and data analysis server. GumTree is being adapted to several instrument control server systems such as TANGO, EPICS and SICS, providing an easy-to-use front-end for users and simple-to-extend model for software developers. The design of GumTree is aimed to be reusable and configurable for any scientific instrument. GumTree will be adapted to six neutron beam instruments for the OPAL reactor at ANSTO. Other European institutes including ESRF, ILL and PSI have shown interest in using GumTree as their workbench for instrument control and data analysis. (authors)

  10. Plant-crafted starches for bioplastics production

    DEFF Research Database (Denmark)

    Sagnelli, Domenico; Hebelstrup, Kim H.; Leroy, Eric

    2016-01-01

    Transgenically-produced amylose-only (AO) starch was used to manufacture bioplastic prototypes. Extruded starch samples were tested for crystal residues, elasticity, glass transition temperature, mechanical properties, molecular mass and microstructure. The AO starch granule crystallinity was both...... in the storage modulus (E') for AO samples compared to the control. The data support the use of pure starch-based bioplastics devoid of non-polysaccharide fillers....... of the B- and Vh-type, while the isogenic control starch was mainly A-type. The first of three endothermic transitions was attributed to gelatinization at about 60°C. The second and third peaks were identified as melting of the starch and amylose-lipid complexes, respectively. After extrusion, the AO...

  11. Application of radiation technology in starch modification

    International Nuclear Information System (INIS)

    Chen Huiyuan; Peng Zhigang; Ding Zhongmin; Lu Jiajiu

    2007-01-01

    In order to commercialize the radiation modification of starch, corn starch was irradiated with different dose of 60 Co gamma radiations. Some basic physical and chemical properties of the resulted modified starch paste were measured with emphasis on the viscosity stability and tensile strength. The results indicate that irradiation of corn starch with a dose of 4-10 kGy can decrease its viscosity to 5-14 mPa·s, and the tensile strength can meet the standard set up for textile paste. In comparison with chemical modification for starch, radiation modification is simpler in technology, more convenient in operation, more stable in modification quality, and easier to control. The mechanism of radiation modification of starch was also discussed. (authors)

  12. Potential of Starch Nanocomposites for Biomedical Applications

    Science.gov (United States)

    Zakaria, N. H.; Muhammad, N.; Abdullah, M. M. A. B.

    2017-06-01

    In recent years, the development of biodegradable materials from renewable sources based on polymeric biomaterials have grown rapidly due to increase environmental concerns and the shortage of petroleum sources. In this regard, naturally renewable polymers such as starch has shown great potential as environmental friendly materials. Besides, the unique properties of starch such as biodegradable and non-toxic, biocompatible and solubility make them useful for a various biomedical applications. Regardless of their unique properties, starch materials are known to have limitations in term of poor processability, low mechanical properties, poor long term stability and high water sensitivity. In order to overcome these limitations, the incorporation of nano size fillers into starch materials (nanocomposites) has been introduced. This review aims to give an overview about structure and characteristics of starch, modification of starch by nanocomposites and their potential for biomedical applications.

  13. In vitro tooth whitening effect of two medicated chewing gums compared to a whitening gum and saliva

    OpenAIRE

    Moore, Michael; Hasler-Nguyen, Nathalie; Saroea, Geoffrey

    2008-01-01

    Abstract Background Extrinsic staining of teeth may result from the deposition of a variety of pigments into or onto the tooth surface, which originate mainly from diet or from tobacco use. More recently, clinical studies have demonstrated the efficacy of some chewing gums in removing extrinsic tooth staining. The aim of this study was to assess the effectiveness of two nicotine medicated chewing gums (A and B) on stain removal in an in vitro experiment, when compared with a confectionary whi...

  14. DISINTEGRATION EFFICIENCY OF SODIUM STARCH GLYCOLATES, PREPARED FROM DIFFERENT NATIVE STARCHES

    NARCIS (Netherlands)

    BOLHUIS, GK; ARENDSCHOLTE, AW; STUUT, GJ; DEVRIES, JA

    1994-01-01

    In a comparative evaluation, the disintegration efficiency of sodium starch glycolates prepared from seven different native starches (potato, maize, waxy maize, wheat, rice, sago and tapioca) were compared. All the sodium starch glycolates tested had a high swelling capacity, but the rate of water

  15. The influence of extruded starch molecular mass on the properties of extruded thermoplastic starch

    NARCIS (Netherlands)

    Soest, van J.J.G.; Benes, K.; Wit, de D.; Vliegenthart, J.F.G.

    1996-01-01

    The mechanical properties of a low and a high molecular mass thermoplastic starch (TPS) were monitored at water contents in the range of 5-30% (w/w). The granular starches were plasticized by extrusion processing with glycerol and water. The low molecular mass starch was prepared by partial acid

  16. The influence of starch molecular mass on the properties of extruded thermoplastic starch

    NARCIS (Netherlands)

    Vliegenthart, J.F.G.; Soest, J.J.G. van; Benes, K.; Wit, D. de

    1996-01-01

    The mechanical properties of a low and a high molecular mass thermoplastic starch (TPS) were monitored at water contents in the range of 5–30% (w/w). The granular starches were plasticized by extrusion processing with glycerol and water. The low molecular mass starch was prepared by partial acid

  17. Starch meets biotechnology : in planta modification of starch composition and functionalities

    NARCIS (Netherlands)

    Xu, Xuan

    2016-01-01

    Storage starch is an energy reservoir for plants and the major source of calories in the human diet. Starch is used in a broad range of industrial applications, as a cheap, abundant, renewable and biodegradable biopolymer. However, starch needs to be modified before it can fulfill the required

  18. Chemically Modified Starch; Allyl- and Epoxy-Starch Derivatives: Their Synthesis and Characterization

    NARCIS (Netherlands)

    Franssen, M.C.R.; Boeriu, C.

    2014-01-01

    Both native and modified starches, such as starch that is pregelatinized, extruded, acid-converted, cross-linked, and substituted, are widely used in industry. This chapter describes a mild two-step process for the synthesis of novel, highly reactive granular epoxy-starch derivatives. Via this

  19. Inducing PLA/starch compatibility through butyl-etherification of waxy and high amylose starch.

    Science.gov (United States)

    Wokadala, Obiro Cuthbert; Emmambux, Naushad Mohammad; Ray, Suprakas Sinha

    2014-11-04

    In this study, waxy and high amylose starches were modified through butyl-etherification to facilitate compatibility with polylactide (PLA). Fourier transform infrared spectroscopy, proton nuclear magnetic resonance spectroscopy and wettability tests showed that hydrophobic butyl-etherified waxy and high amylose starches were obtained with degree of substitution values of 2.0 and 2.1, respectively. Differential scanning calorimetry, tensile testing, and scanning electron microscopy (SEM) demonstrated improved PLA/starch compatibility for both waxy and high amylose starch after butyl-etherification. The PLA/butyl-etherified waxy and high amylose starch composite films had higher tensile strength and elongation at break compared to PLA/non-butyl-etherified composite films. The morphological study using SEM showed that PLA/butyl-etherified waxy starch composites had a more homogenous microstructure compared to PLA/butyl-etherified high amylose starch composites. Thermogravimetric analysis showed that PLA/starch composite thermal stability decreased with starch butyl-etherification for both waxy and high amylose starches. This study mainly demonstrates that PLA/starch compatibility can be improved through starch butyl-etherification. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. COORDINATION OF CASSAVA STARCH TO METAL IONS AND ...

    African Journals Online (AJOL)

    a

    starch. On the other hand, the decomposition proceeded at a lower rate than the decomposition of ... Metal salts influenced the thermal decomposition of starches [4, 5]. Thus, properly ..... reactions of starch resulting in dextrins. After the ...

  1. The role of time on task performance in modifying the effects of gum chewing on attention.

    Science.gov (United States)

    Tucha, Lara; Simpson, William

    2011-04-01

    Recent research examined the effects of chewing gum on attention and reported a significant interaction of gum chewing with time. Using a crossover within-subject design, the present study examined the effect of gum chewing on sustained attention in healthy adults over a period of 30 min. The results revealed a significant main effect of time and a significant interaction between gum chewing and time. The findings suggest that gum chewing differentially affects attention performance. While gum chewing has detrimental effects on sustained attention in earlier stages of the task, beneficial effects on sustained attention were observed at later stages. Copyright © 2010 Elsevier Ltd. All rights reserved.

  2. Defining Starch Binding by Glucan Phosphatases

    DEFF Research Database (Denmark)

    Auger, Kyle; Raththagala, Madushi; Wilkens, Casper

    2015-01-01

    Starch is a vital energy molecule in plants that has a wide variety of uses in industry, such as feedstock for biomaterial processing and biofuel production. Plants employ a three enzyme cyclic process utilizing kinases, amylases, and phosphatases to degrade starch in a diurnal manner. Starch...... is comprised of the branched glucan amylopectin and the more linear glucan amylose. Our lab has determined the first structures of these glucan phosphatases and we have defined their enzymatic action. Despite this progress, we lacked a means to quickly and efficiently quantify starch binding to glucan...

  3. Atomic force microscopy of starch systems.

    Science.gov (United States)

    Zhu, Fan

    2017-09-22

    Atomic force microscopy (AFM) generates information on topography, adhesion, and elasticity of sample surface by touching with a tip. Under suitable experimental settings, AFM can image biopolymers of few nanometers. Starch is a major food and industrial component. AFM has been used to probe the morphology, properties, modifications, and interactions of starches from diverse botanical origins at both micro- and nano-structural levels. The structural information obtained by AFM supports the blocklet structure of the granules, and provides qualitative and quantitative basis for some physicochemical properties of diverse starch systems. It becomes evident that AFM can complement other microscopic techniques to provide novel structural insights for starch systems.

  4. Analytical studies on the gum exudate from Anogeissus leiocarpus

    International Nuclear Information System (INIS)

    Ahmed, Samia Eltayeb

    1999-04-01

    Anogeissus leiocarpus gum samples were collected as natural exudate nodules, from three different location. Physicochemical properties of gum samples were studied. results showed significant differences within each location in most parameters studied except refractive index value which was found to be constant in all samples. The effect of location on the properties of gum samples was also studied and the analysis of variance showed insignificant differences (P≤0.05) in all properties studied except in ash content. Inter nodule variations of gum from two different location were studied individually. Results showed significant differences for each parameter studied except for the refractive index value. The properties studied of all gum samples were as follows: 9.2% moisture, 3.4% ash, 0.72% nitrogen, 4.74% protein, -35.5 specific rotation, 1.68 relative viscosity, 4.2 pH, 1.334 refractive index, 14.3 uronic acid, 0.44% reducing sugar, 1336.0 equivalent weight and 0.68% tannin content. UV absorption spectra of gum samples and gum nodules were determined. Cationic composition of gum samples was also determined and the results showed that (Mg) has highest value in all samples studied followed by Fe, Na, K, Ca, Zn and trace amount of Mn, Co, Ni, Cd and Pb. The water holding capacity was found to be 65.5% and emulsifying stability was found to be 1.008. The component sugars of gum were examined by different methods followed by qualitative and quantitative analysis. Analysis of hydrolysate crude gum sample by HPLC show L-rhamnose (6.82), L-arabinose (48.08), D-galactose (11.26) and two unknown oligosaccharides having values (0.22 and 32.61). Some physicochemical properties were studied. Results showed significant differences in nitrogen and protein contents, specific rotation, relative viscosity, equivalent weight and pH of fractions, where as insignificant differences were observed in uronic acid content and refractive index values

  5. Solar drying of uruguayan red gum

    Directory of Open Access Journals (Sweden)

    Andrés Ono

    2011-04-01

    Full Text Available he use of solar energy as an alternative to non-renewable energy sources has been widely researched in the last decades. Compared to air drying, solar drying kilns can better control the drying process, resulting in a higher quality of the dry wood and lower final wood moisture content values. Investment and running costs for a solar drying kiln are lower than those of a conventional kiln. Moreover, the solar drying process can be advantageous for drying hardwoods which are traditionally considered difficult to dry such as eucalyptus wood of medium and high density (Red gums, known in Spanish as “Eucaliptos colorados”. The solar drying kiln naturally incorporates a daily high relative humidity period that can be similar to a conditioning or steaming step, although at a lower temperature.This results in fewer defects due to the drying process.A pilot scale 2.5 m3 semi-greenhouse type solar wood drying kiln was constructed at LATU (Uruguay Technological Laboratory in Montevideo, Uruguay. The operating conditions and the results from two drying runs are presented. Two species of red gum (Eucalyptus tereticornis Sm., ADD 870 kg/m3, and Eucalyptus camaldulensis Dehnh., ADD 800 kg/m3 were dried from initial average moisture contents (WMC of around 60% down to 10.0% and 12.7% in 108 days and 76 days, respectively. Boards were provided by the Grupo Forestal San Gregorio from trees harvested at Tacuarembo and Paysandu Departments from cattle shelter forests 60 and 70 years old.Mean volume shrinkage was 18% for E. tereticornis, and 16% for E. camaldulensis, and the level of defects was moderate. Residual stresses and moisture content gradients were observed for both species. Final moisture content values were similar compared to those obtained in conventional drying kilns but with longer drying periods and lower operating costs. This would make the solar drying process attractive to small and medium sized forest products industries in a small country

  6. Effect of Angum gum in combination with tragacanth gum on rheological and sensory properties of ketchup.

    Science.gov (United States)

    Komeilyfard, Ahmadreza; Fazel, Mohammad; Akhavan, Hamidreza; Mousakhani Ganjeh, Alireza

    2017-04-01

    The aim of this study was to evaluate the effect of Angum gum (AnG) alone and in combination with tragacanth gum (TG) on the stability, texture, sensory, and rheological properties of tomato ketchup. AnG, TG, and Angum gum and tragacanth gum mixture (AnGT; 1:1 ratio) were added at levels of 0.5, 1, and 1.5%. Ten tomato ketchup formulations were produced: control (without hydrocolloid), AnG (0.5-1.5%), TG (0.5-1.5%), AnGT (0.5-1.5%). It was observed that the hydrocolloids addition to tomato ketchup significantly decreased the Bostwick consistency value and serum separation at 2200, 5000, and 8800 g. Textural properties of tomato ketchup by using back extrusion test and particle size analysis were significantly increased with hydrocolloid addition. All tomato ketchup formulations showed shear thinning behavior and the addition of hydrocolloids increased apparent viscosity. The power law and Herschel-Bulkley models were successfully fitted with experimental data. The flow behavior indices of Herschel-Bulkley and power law models were changed in the range of 0.19-0.24 and 0.14-0.30, respectively. The consistency coefficients of these models were in the range of 16.31-79.57 and 11.19-146.06 Pa s n , respectively. The storage modulus (G') of all tomato ketchups was higher than the loss modulus (G″). Hydrocolloid addition showed no significant effect on the color indices (L*, a*, b*, hue angle, chroma, and total color differences) of tomato ketchup. The overall acceptability of 1.5% AnG, 0.5% TG, 1 and 1.5% AnGT were significantly higher than other samples. Therefore, AnG can be used alone and in combination with TG as stabilizer in tomato ketchup. The consistency of tomato ketchup is an important attribute from both engineering and consumer viewpoints. It was observed that addition of TG, AnG, and AnGT to tomato ketchups significantly decreased their Bostwick consistency values and their serum separation. In addition, hydrocolloid addition showed no significant effect

  7. Characterization of Native and Modified Starches by Potentiometric Titration

    OpenAIRE

    Soto, Diana; Urdaneta, Jose; Pernia, Kelly

    2014-01-01

    The use of potentiometric titration for the analysis and characterization of native and modified starches is highlighted. The polyelectrolytic behavior of oxidized starches (thermal and thermal-chemical oxidation), a graft copolymer of itaconic acid (IA) onto starch, and starch esters (mono- and diester itaconate) was compared with the behavior of native starch, the homopolymer, and the acid employed as a graft monomer and substituent. Starch esters showed higher percentages of acidity, follo...

  8. Structural and molecular basis of starch viscosity in hexaploid wheat.

    Science.gov (United States)

    Ral, J-P; Cavanagh, C R; Larroque, O; Regina, A; Morell, M K

    2008-06-11

    Wheat starch is considered to have a low paste viscosity relative to other starches. Consequently, wheat starch is not preferred for many applications as compared to other high paste viscosity starches. Increasing the viscosity of wheat starch is expected to increase the functionality of a range of wheat flour-based products in which the texture is an important aspect of consumer acceptance (e.g., pasta, and instant and yellow alkaline noodles). To understand the molecular basis of starch viscosity, we have undertaken a comprehensive structural and rheological analysis of starches from a genetically diverse set of wheat genotypes, which revealed significant variation in starch traits including starch granule protein content, starch-associated lipid content and composition, phosphate content, and the structures of the amylose and amylopectin fractions. Statistical analysis highlighted the association between amylopectin chains of 18-25 glucose residues and starch pasting properties. Principal component analysis also identified an association between monoesterified phosphate and starch pasting properties in wheat despite the low starch-phosphate level in wheat as compared to tuber starches. We also found a strong negative correlation between the phosphate ester content and the starch content in flour. Previously observed associations between internal starch granule fatty acids and the swelling peak time and pasting temperature have been confirmed. This study has highlighted a range of parameters associated with increased starch viscosity that could be used in prebreeding/breeding programs to modify wheat starch pasting properties.

  9. A NEW SPECIES OF INVASIVE GALL WASP (HYMENOPTERA: EULOPHIDAE: TETRASTICHINAE) ON BLUE GUM (EUCALYPTUS GLOBULUS) IN CALIFORNIA

    Science.gov (United States)

    The blue gum gall wasp, Selitrichodes globulus La Salle & Gates (Hymenoptera: Eulophidae: Tetrastichinae), is described as an invasive gall inducer on blue gum, Eucalyptus globulus (Myrtaceae), in California....

  10. Superelastic load cycling of Gum Metal

    International Nuclear Information System (INIS)

    Vorontsov, V.A.; Jones, N.G.; Rahman, K.M.; Dye, D.

    2015-01-01

    The superelastic beta titanium alloy, Gum Metal, has been found to accumulate plastic strain during tensile load cycling in the superelastic regime. This is evident from the positive drift of the macroscopic stress vs. strain hysteresis curve parallel to the strain axis and the change in its geometry subsequent to every load–unload cycle. In addition, there is a progressive reduction in the hysteresis loop width and in the stress at which the superelastic transition occurs. In situ synchrotron X-ray diffraction has shown that the lattice strain exhibited the same behaviour as that observed in macroscopic measurements and identified further evidence of plastic strain accumulation. The mechanisms responsible for the observed behaviour have been evaluated using transmission electron microscopy, which revealed a range of different defects that formed during load cycling. The formation of these defects is consistent with the classical mathematical theory for the bcc to orthorhombic martensitic transformation. It is the accumulation of these defects over time that alters its superelastic behaviour

  11. Aplikasi Campuran Alginat Dari Sargassum Crassifolium Dan Gum Sebagai Pengental Textile Printing

    Directory of Open Access Journals (Sweden)

    Subaryono Subaryono

    2015-12-01

    Full Text Available Penelitian aplikasi campuran alginat dari Sargassum crassifolium dan gum untuk meningkatkan viskositas alginat sebagai pengental pada textile printing telah dilakukan. Viskositas campuran alginat dengan guar gum, gum arab, dan locust bean gum diamati pada penyimpanan selama 8 jam. Produk terbaik diujikan sebagai pengental pada textile printing. Campuran alginat dengan guar gum pada perbandingan 90:10 dan 80:20 meningkatkan viskositas dan stabilitas alginat selama penyimpanan. Campuran alginat dengan gum arab dan locust bean gum akan menurunkan viskositas alginat sehingga tidak sesuai untuk aplikasi textile printing. Aplikasi campuran alginat dengan guar gum 90:10 dan 80:20 sebagai pengental pada tekstil printing menghasilkan produk akhir yang setara dengan pengental komersial manutex.

  12. STUDIES ON SOME PHYSICOCHEMICAL PROPERTIES OF LEUCAENA LEUCOCEPHALA BARK GUM

    Directory of Open Access Journals (Sweden)

    Vijetha Pendyala

    2010-06-01

    Full Text Available Gum exudates from Leucaena Leucocephala (Family: Fabaceae plants grown all over India were investigated for its physicochemical properties such as pH, swelling capacity and viscosities at different temperatures using standard methods. Leucaena Leucocephala bark gum appeared to be colorless to reddish brown translucent tears. 5 % w/v mucilage has pH of 7.5 at 28°C. The gum is slightly soluble in water and practically insoluble in ethanol, acetone and chloroform. It swells to about 5 times its original weight in water. A 5 %w/v mucilage concentration gave a viscosity value which was unaffected at temperature ranges (28-40°C. At concentrations of 2 and 5 %w/v, the gum exhibited pseudo plastic flow pattern while at 10 %w/v concentration the flow behaviour was thixotropic. The results indicate that the swelling ability of Leucaena Leucocephala (LL bark gum may provide potentials for its use as a disintegrant in tablet formulation, as a hydro gel in modified release dosage forms and the rheological flow properties may also provide potentials for its use as suspending and emulsifying agents owing to its pseudo plastic and thixotropic flow patterns.

  13. The impact of chewing gum resistance on immediate free recall.

    Science.gov (United States)

    Rickman, Sarah; Johnson, Andrew; Miles, Christopher

    2013-08-01

    Although the facilitative effects of chewing gum on free recall have proved contentious (e.g., Tucha, Mecklinger, Maier, Hammerl, & Lange, 2004; Wilkinson, Scholey, & Wesnes, 2002), there are strong physiological grounds, for example, increased cerebral activity and blood flow following the act of mastication, to suppose facilitation. The present study manipulated resistance to mastication, that is, chewing four pellets versus one pellet of gum, with the assumption that increased resistance will accentuate cerebral activity and blood flow. Additionally, chewing rate was recorded for all participants. In a within-participants design, participants performed a series of immediate free recall tasks while chewing gum at learning (one or four pellets) and recall (one or four pellets). Increased chewing resistance was not associated with increased memory performance, despite consistent chewing rates for both the one and four pellet conditions at both learning and recall. However, a pattern of recall consistent with context-dependent memory was observed. Here, participants who chewed the equivalent number of gum pellets at both learning and recall experienced significantly superior word recall compared to those conditions where the number of gum pellets differed. ©2012 The British Psychological Society.

  14. Using Gamma Irradiation to Modify Properties of Polysaccharides (Guar Gum)

    International Nuclear Information System (INIS)

    Sayed, H.

    2015-01-01

    Radiation processing of material is one of most recent technology used in modification of material properties. The aim of this work was to determine the effect of gamma irradiation on the Polysaccharides Viscosity and Molecular Weight, as definition of Guar Gum. Its series of glactomanene (glactos + manose). (1-2-,3). Guar Gum powder was the main material and Co-60 irradiator facility as main technique. For gamma–ray source of required doses, 2.5, 5, 7.5, 10, 20, 30, 40 and 50 kGy. Viscosity of the aqueous suspensions of irradiated Guar Gum at different concentrations (0.1–0.5%) was measured, also it measured for solutions made of irradiated powder. Results used to calculate the difference occur in molecular weight, in order to determine the irradiation effect in the material. The monitored rheological parameters showed (non-Newtonian Behavior) of the samples which processed by gamma irradiation. The decrease tendency of the viscosity by irradiation of samples under study (different concentrations) and compared with control also for irradiated powder decrease of the concentration as well has been noticed. From results evaluation concluded that the viscosity values for all studied concentrations decreased by irradiation. This aspect suggests a depolymerization phenomenon of the aqueous Guar Gum solutions. This study contributes to the knowledge of the viscoelastic properties of Guar Gum as powder or aqueous solution, with application for food, agriculture, medical products, Petroleum and construction. (author)

  15. Development of starch-based materials

    NARCIS (Netherlands)

    Habeych Narvaez, E.A.

    2009-01-01

    Starch-based materials show potential as fully degradable plastics. However, the current
    applicability of these materials is limited due to their poor moisture tolerance and
    mechanical properties. Starch is therefore frequently blended with other polymers to make
    the material more

  16. Antimicrobial nanostructured starch based films for packaging.

    Science.gov (United States)

    Abreu, Ana S; Oliveira, M; de Sá, Arsénio; Rodrigues, Rui M; Cerqueira, Miguel A; Vicente, António A; Machado, A V

    2015-09-20

    Montmorillonite modified with a quaternary ammonium salt C30B/starch nanocomposite (C30B/ST-NC), silver nanoparticles/starch nanocomposite (Ag-NPs/ST-NC) and both silver nanoparticles/C30B/starch nanocomposites (Ag-NPs/C30B/ST-NC) films were produced. The nanoclay (C30B) was dispersed in a starch solution using an ultrasonic probe. Different concentrations of Ag-NPs (0.3, 0.5, 0.8 and 1.0mM) were synthesized directly in starch and in clay/starch solutions via chemical reduction method. Dispersion of C30B silicate layers and Ag-NPs in ST films characterized by X-ray and scanning electron microscopy showed that the presence of Ag-NPs enhanced clay dispersion. Color and opacity measurements, barrier properties (water vapor and oxygen permeabilities), dynamic mechanical analysis and contact angle were evaluated and related with the incorporation of C30B and Ag-NPs. Films presented antimicrobial activity against Staphylococcus aureus, Escherichia coli and Candida albicans without significant differences between Ag-NPs concentrations. The migration of components from the nanostructured starch films, assessed by food contact tests, was minor and under the legal limits. These results indicated that the starch films incorporated with C30B and Ag-NPs have potential to be used as packaging nanostructured material. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Semicontinuous saccharification of starch in alcohol production

    Energy Technology Data Exchange (ETDEWEB)

    Danilyak, N.I.; Kaminskil, R.S.; Shvedov, A.D.

    1959-05-21

    The saccharification is accomplished with an enzyme preparation of Aspergillus oryzae. In the first stage, the starch is treated at 57 to 59/sup 0/ with a fermenting solution containing 1% enzyme based on the starch content. The second step is carried out in the fermenting solution containing 2.5% enzyme.

  18. Starch and cellulose nanocrystals together into thermoplastic starch bionanocomposites.

    Science.gov (United States)

    González, Kizkitza; Retegi, Aloña; González, Alba; Eceiza, Arantxa; Gabilondo, Nagore

    2015-03-06

    In the present work, thermoplastic maize starch based bionanocomposites were prepared as transparent films, plasticized with 35% of glycerol and reinforced with both waxy starch (WSNC) and cellulose nanocrystals (CNC), previously extracted by acidic hydrolysis. The influence of the nanofiller content was evaluated at 1 wt.%, 2.5 wt.% and 5 wt.% of WSNC. The effect of adding the two different nanoparticles at 1 wt.% was also investigated. As determined by tensile measurements, mechanical properties were improved at any composition of WSNC. Water vapour permeance values maintained constant, whereas barrier properties to oxygen reduced in a 70%, indicating the effectiveness of hydrogen bonding at the interphase. The use of CNC or CNC and WSNC upgraded mechanical results, but no significant differences in barrier properties were obtained. A homogeneous distribution of the nanofillers was demonstrated by atomic force microscopy, and a shift of the two relaxation peaks to higher temperatures was detected by dynamic mechanical analysis. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Acetylation and characterization of banana (Musa paradisiaca) starch.

    Science.gov (United States)

    Bello-Pérez, L A; Contreras-Ramos, S M; Jìmenez-Aparicio, A; Paredes-López, O

    2000-01-01

    Banana native starch was acetylated and some of its functional properties were evaluated and compared to corn starch. In general, acetylated banana starch presented higher values in ash, protein and fat than corn acetylated starch. The modified starches had minor tendency to retrogradation assessed as % transmittance of starch pastes. At high temperature acetylated starches presented a water retention capacity similar to their native counterpart. The acetylation considerably increased the solubility of starches, and a similar behavior was found for swelling power. When freeze-thaw stability was studied, acetyl banana starch drained approximately 60% of water in the first and second cycles, but in the third and fourth cycles the percentage of separated water was low. However, acetyl corn starch showed lower freeze-thaw stability than the untreated sample. The modification increased the viscosity of banana starch pastes.

  20. Effects of chewing gum on mood, learning, memory and performance of an intelligence test.

    Science.gov (United States)

    Smith, Andrew

    2009-04-01

    Recent research suggests that chewing gum may increase alertness and lead to changes in cognitive performance. The present study examined effects of chewing gum on these functions within the context of a single study. This study had four main aims. The first was to examine whether chewing gum improved learning and memory of information in a story. The second aim was to determine whether chewing gum improved test performance on a validated intellectual task (the Alice Heim task). A third aim was to determine whether chewing gum improved performance on short memory tasks (immediate and delayed recall of a list of words, delayed recognition memory, retrieval from semantic memory, and a working memory task). The final aim was to determine whether chewing gum improved mood (alertness, calm and hedonic tone). A cross-over design was used with gum and no-gum sessions being on consecutive weeks. In each week, volunteers attended for two sessions, two days apart. The first session assessed mood, immediate recall of information from a story and performance on short memory tasks. The second session assessed mood, delayed recall of information from a story and performance of an intelligence test (the Alice Heim test). There were no significant effects of chewing gum on any aspect of recall of the story. Chewing gum improved the accuracy of performing the Alice Heim test which confirms the benefits of gum on test performance seen in an earlier study. Chewing gum had no significant effect on the short memory tasks. Chewing gum increased alertness at the end of the test session in both parts of the study. This effect was in the region of a 10% increase and was highly significant (P increases alertness. In contrast, no significant effects of chewing gum were observed in the memory tasks. Intellectual performance was improved in the gum condition. Overall, the results suggest further research on the alerting effects of chewing gum and possible improved test performance in these

  1. Effects of xanthan, guar, carrageenan and locust bean gum addition on physical, chemical and sensory properties of meatballs.

    Science.gov (United States)

    Demirci, Zeynep Ozben; Yılmaz, Ismail; Demirci, Ahmet Şukru

    2014-05-01

    This study evaluated the effects of xanthan gum, guar gum, carrageenan and locust bean gum on physical, chemical and sensory properties of meatballs. Meatball samples were produced with three different formulations including of 0.5, 1, and 1.5% each gum addition and gum added samples were compared with the control meatballs. Physical and chemical analyses were carried out on raw and cooked samples separately. Moisture contents of raw samples decreased by addition of gums. There were significant decreases (p meatball samples formulated with gum when compared with control. Ash contents and texture values increased with gum addition to meatballs. Meatball redness decreased with more gum addition in raw and cooked meatball samples, which means that addition of gums resulted in a lighter-coloured product. According to sensory analysis results, locust bean gum added (1%) samples were much preferred by the panelists.

  2. Evaluation of the Binding Effect of Local Gum of Boswellia papyrifera ...

    African Journals Online (AJOL)

    In this work, B. papyrifera gum has been evaluated for its binding effect in paracetamol granules and tablet formulations in comparison with the commonly used binders, Acacia BP and PVP K-30. Some physicochemical properties of the extracted gum indicated that the gum exhibited solubility in water, absence of tannin and ...

  3. Fluoride and urea chewing gums in an intra-oral experimental caries model

    NARCIS (Netherlands)

    Sjogren, K; Ruben, J; Lingstrom, P; Lundberg, AB; Birkhed, D

    2002-01-01

    The aim of the present investigation was to evaluate the effect of sugar-free chewing gums containing fluoride (F) and urea in an intra-oral experimental caries model. Placebo chewing gums (without any active ingredient) and no gum served as controls. Fifteen subjects participated in a cross-over,

  4. TECHNICAL NOTE: The effect of the green additive guar gum on the properties of magnetorheological fluid

    Science.gov (United States)

    Fang, Chen; Zhao, Bin Yuan; Chen, LeSheng; Wu, Qing; Liu, Nan; Hu, Ke Ao

    2005-02-01

    Magnetorheological (MR) fluid containing guar gum was prepared for the first time by ball-milling the guar gum powder together with silicone oil and carbonyl iron powder. By forming a coating layer over the ground carbonyl iron powder, the guar gum improves the sedimentation stability and thixotropy of the MR fluid effectively.

  5. The role of time on task performance in modifying the effects of gum chewing on attention

    NARCIS (Netherlands)

    Tucha, Lara; Simpson, William

    Recent research examined the effects of chewing gum on attention and reported a significant interaction of gum chewing with time. Using a crossover within-subject design, the present study examined the effect of gum chewing on sustained attention in healthy adults over a period of 30 min. The

  6. Oxidation of cashew tree gum exudate polysaccharide with TEMPO reagent

    Energy Technology Data Exchange (ETDEWEB)

    Cunha, Pablyana L.R.; Maciel, Jeanny S.; Paula, Regina C.M. de; Feitosa, Judith P.A. [Universidade Federal do Ceara, Fortaleza, CE (Brazil). Dept. de Quimica Organica e Inorganica; Sierakowski, Maria Rita [Universidade Federal do Parana, Curitiba, PR (Brazil). Dept. de Quimica]. E-mail: judith@dqoi.ufc.br

    2007-07-01

    Cashew gum (CG), an exudate polysaccharide from Anacardium occidentale trees, was oxidized with TEMPO reagent and the product (CGOX) characterized by spectroscopic techniques (FTIR and NMR), chromatographic analyses (HPLC and GPC), viscosity measurements and thermal analysis (TGA). The yield of the reaction product was 96%. The uronic acid content in starting gum (7.2 m%) was increased to 36 m%. The degree of oxidation based on free galactose and glucose units was 68%. NMR data show that oxidation occurred preferentially at primary carbons of galactose units. High degradation degree after oxidation was estimated by the difference on the expected and observed {eta}{sub CGOX}/{eta}{sub CG} ratio. The presence of organic and inorganic impurities in the new polyelectrolyte was detected by TGA. A less thermally stable cashew gum is formed after the oxidation with TEMPO based on initial decomposition temperature and IPDT. (author)

  7. Development of controlled release spheroids using Buchananiacochinchinesis gum

    Directory of Open Access Journals (Sweden)

    Narayan Babulal Gaikwad

    2013-03-01

    Full Text Available Chirauli nut gum was isolated from the bark of Buchanania cochinchinesis (fam. Anacadiacea and was used as a release modifier for the preparation of Diclofenac sodium spheroids using the extrusion spheronization technique. The process was studied for the effects on variables when making spheroids with satisfactory particle shape, size and size distribution. The prepared spheroids were characterized for surface morphology, qualitative surface porosity, friability, bulk density and flow properties. In vitro studies demonstrated that the release exhibited Fickian diffusion kinetics which was confirmed by the Higuchi and the Korsmeyer-Peppas models. The physico-chemical parameters of the gum could be correlated to the in vitro dissolution profile of the spheroids. The spheroids were not able to sustain the drug releases over 12 hours. A greater concentration of Chirauli nut gum and a process that can accommodate such greater concentrations may produce a formulation capable of significant sustained release.

  8. Oxidation of cashew tree gum exudate polysaccharide with TEMPO reagent

    International Nuclear Information System (INIS)

    Cunha, Pablyana L.R.; Maciel, Jeanny S.; Paula, Regina C.M. de; Feitosa, Judith P.A.; Sierakowski, Maria Rita

    2007-01-01

    Cashew gum (CG), an exudate polysaccharide from Anacardium occidentale trees, was oxidized with TEMPO reagent and the product (CGOX) characterized by spectroscopic techniques (FTIR and NMR), chromatographic analyses (HPLC and GPC), viscosity measurements and thermal analysis (TGA). The yield of the reaction product was 96%. The uronic acid content in starting gum (7.2 m%) was increased to 36 m%. The degree of oxidation based on free galactose and glucose units was 68%. NMR data show that oxidation occurred preferentially at primary carbons of galactose units. High degradation degree after oxidation was estimated by the difference on the expected and observed η CGOX /η CG ratio. The presence of organic and inorganic impurities in the new polyelectrolyte was detected by TGA. A less thermally stable cashew gum is formed after the oxidation with TEMPO based on initial decomposition temperature and IPDT. (author)

  9. Tragacanth gum: an effective oil well drilling fluid additive

    Energy Technology Data Exchange (ETDEWEB)

    Mahto, V.; Sharma, V. [Indian School of Mines, Dhanbad (India). Department of Petroleum Engineering

    2005-02-15

    The low penetration rate, excessive torque and drag, poor hole cleaning and formation damage are major impediments in drilling oil and gas well. These have a major impact on drilling efficiency and well economics. Keeping these in mind, an attempt was made to design a water based drilling fluid system using Indian bentonite clays and tragacanth gum. The effect of tragacanth gum on rheological behavior of three different Indian bentonite water suspensions was studied and a drilling fluid system was developed. The filtrates of these drilling fluids were subjected to formation damage study on the field core using Ruska Liquid Permeameter. The laboratory investigation furnishes that tragacanth gum acts as a good viscosifier and fluid loss control agent. The drilling fluid filtrate also has less effect on formation damage. (author)

  10. Design, formulation and evaluation of Aloe vera chewing gum

    Science.gov (United States)

    Aslani, Abolfazl; Ghannadi, Alireza; Raddanipour, Razieh

    2015-01-01

    Background: Aloe vera has antioxidant, antiinflammatory, healing, antiseptic, anticancer and antidiabetic effects. The aim of the present study was to design and evaluate the formulation of Aloe vera chewing gum with an appropriate taste and quality with the indications for healing oral wounds, such as lichen planus, mouth sores caused by cancer chemotherapy and mouth abscesses as well as reducing mouth dryness caused by chemotherapy. Materials and Methods: In Aloe vera powder, the carbohydrate content was determined according to mannose and phenolic compounds in terms of gallic acid. Aloe vera powder, sugar, liquid glucose, glycerin, sweeteners and different flavors were added to the soft gum bases. In Aloe vera chewing gum formulation, 10% of dried Aloe vera extract entered the gum base. Then the chewing gum was cut into pieces of suitable sizes. Weight uniformity, content uniformity, the organoleptic properties evaluation, releasing the active ingredient in the phosphate buffer (pH, 6.8) and taste evaluation were examined by Latin square method. Results: One gram of Aloe vera powder contained 5.16 ± 0.25 mg/g of phenolic compounds and 104.63 ± 4.72 mg/g of carbohydrates. After making 16 Aloe vera chewing gum formulations, the F16 formulation was selected as the best formulation according to its physicochemical and organoleptic properties. In fact F16 formulation has suitable hardness, lack of adhesion to the tooth and appropriate size and taste; and after 30 min, it released more than 90% of its drug content. Conclusion: After assessments made, the F16 formulation with maltitol, aspartame and sugar sweeteners was selected as the best formulation. Among various flavors used, peppermint flavor which had the most acceptance between consumers was selected. PMID:26605214

  11. Comparison of gamma radiation effects on natural corn and potato starches and modified cassava starch

    Science.gov (United States)

    Teixeira, Bruna S.; Garcia, Rafael H. L.; Takinami, Patricia Y. I.; del Mastro, Nelida L.

    2018-01-01

    The objective of this work was to evaluate the effect of irradiation treatment on physicochemical properties of three natural polymers, i.e. native potato and corn starches and a typical Brazilian product, cassava starch modified through fermentation -sour cassava- and also to prepare composite hydrocolloid films based on them. Starches were irradiated in a 60Co irradiation chamber in doses up to 15 kGy, dose rate about 1 kGy/h. Differences were found in granule size distribution upon irradiation, mainly for corn and cassava starch but radiation did not cause significant changes in granule morphology. The viscosity of the potato, corn and cassava starches hydrogels decreased as a function of absorbed dose. Comparing non-irradiated and irradiated starches, changes in the Fourier transform infrared (FTIR) spectra in the 2000-1500 cm-1 region for potato and corn starches were observed but not for the cassava starch. Maximum rupture force of the starch-based films was affected differently for each starch type; color analysis showed that doses of 15 kGy promoted a slight rise in the parameter b* (yellow color) while the parameter L* (lightness) was not significantly affected; X-ray diffraction patterns remained almost unchanged by irradiation.

  12. Starch Origin and Thermal Processing Affect Starch Digestion in a Minipig Model of Pancreatic Exocrine Insufficiency.

    Science.gov (United States)

    Mößeler, Anne; Vagt, Sandra; Beyerbach, Martin; Kamphues, Josef

    2015-01-01

    Although steatorrhea is the most obvious symptom of pancreatic exocrine insufficiency (PEI), enzymatic digestion of protein and starch is also impaired. Low praecaecal digestibility of starch causes a forced microbial fermentation accounting for energy losses and meteorism. To optimise dietetic measures, knowledge of praecaecal digestibility of starch is needed but such information from PEI patients is rare. Minipigs fitted with an ileocaecal fistula with (n = 3) or without (n = 3) pancreatic duct ligation (PL) were used to estimate the rate of praecaecal disappearance (pcD) of starch. Different botanical sources of starch (rice, amaranth, potato, and pea) were fed either raw or cooked. In the controls (C), there was an almost complete pcD (>92%) except for potato starch (61.5%) which was significantly lower. In PL pcD of raw starch was significantly lower for all sources of starch except for amaranth (87.9%). Thermal processing increased pcD in PL, reaching values of C for starch from rice, potato, and pea. This study clearly underlines the need for precise specification of starch used for patients with specific dietetic needs like PEI. Data should be generated in suitable animal models or patients as tests in healthy individuals would not have given similar conclusions.

  13. Starch Origin and Thermal Processing Affect Starch Digestion in a Minipig Model of Pancreatic Exocrine Insufficiency

    Directory of Open Access Journals (Sweden)

    Anne Mößeler

    2015-01-01

    Full Text Available Although steatorrhea is the most obvious symptom of pancreatic exocrine insufficiency (PEI, enzymatic digestion of protein and starch is also impaired. Low praecaecal digestibility of starch causes a forced microbial fermentation accounting for energy losses and meteorism. To optimise dietetic measures, knowledge of praecaecal digestibility of starch is needed but such information from PEI patients is rare. Minipigs fitted with an ileocaecal fistula with (n=3 or without (n=3 pancreatic duct ligation (PL were used to estimate the rate of praecaecal disappearance (pcD of starch. Different botanical sources of starch (rice, amaranth, potato, and pea were fed either raw or cooked. In the controls (C, there was an almost complete pcD (>92% except for potato starch (61.5% which was significantly lower. In PL pcD of raw starch was significantly lower for all sources of starch except for amaranth (87.9%. Thermal processing increased pcD in PL, reaching values of C for starch from rice, potato, and pea. This study clearly underlines the need for precise specification of starch used for patients with specific dietetic needs like PEI. Data should be generated in suitable animal models or patients as tests in healthy individuals would not have given similar conclusions.

  14. Chewing gum and lozenges as delivery systems for noscapine

    DEFF Research Database (Denmark)

    Norgaard Jensen, L.; Christrup, Lona Louring; Menger, N.

    1991-01-01

    Chewing gum and lozenges were evaluated as delivery systems for noscapine with the aim of developing improved antitussive preparations. The formulations studied were prepared with both the water-soluble hydrochloride salt of noscapine and with the poorly soluble embonate salt and noscapine free...... base. The release characteristics of the preparations were evaluated both in vitro and in vivo, and their taste properties examined. Only the formulations containing noscapine base were without any appreciable taste. Chewing gum containing this compound showed, however, a low level of drug release both...

  15. A comparative study of the physicochemical properties of starches ...

    African Journals Online (AJOL)

    Some properties of starches from cassava, potato and sweet potato were compared with cereal starches from maize, wheat, millet and sorghum. The aim was to determine the properties of tuber and root crop starches and compare them with cereal starches in addition to unravelling the potential of commonly grown ...

  16. Fluorescence spectral studies of Gum Arabic: Multi-emission of Gum Arabic in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Dhenadhayalan, Namasivayam, E-mail: ndhena@gmail.com [Department of Chemistry, National Taiwan University, Taipei, Taiwan (China); Mythily, Rajan, E-mail: rajanmythily@gmail.com [Department of Chemistry, Dwaraka Doss Goverdhan Doss Vaishnav College (Autonomous), 833, Gokul Bagh, E.V.R. Periyar Road, Arumbakkam, Chennai 600 106 (India); Kumaran, Rajendran, E-mail: kumaranwau@rediffmail.com [Department of Chemistry, Dwaraka Doss Goverdhan Doss Vaishnav College (Autonomous), 833, Gokul Bagh, E.V.R. Periyar Road, Arumbakkam, Chennai 600 106 (India)

    2014-11-15

    Gum Arabic (GA), a food hydrocolloid is a natural composite obtained from the stems and branches of Acacia Senegal and Acacia Seyal trees. GA structure is made up of highly branched arabinogalactan polysaccharides. Steady-state absorption, fluorescence, and time-resolved fluorescence spectral studies of acid hydrolyzed GA solutions were carried out at various pH conditions. The fluorescence in GA is predominantly attributed to the presence of tyrosine and phenylalanine amino acids. The presence of multi-emissive peaks at different pH condition is attributed to the exposure of the fluorescing amino acids to the aqueous phase, which contains several sugar units, hydrophilic and hydrophobic moieties. Time-resolved fluorescence studies of GA exhibits a multi-exponential decay with different fluorescence lifetime of varying amplitude which confirms that tyrosine is confined to a heterogeneous microenvironment. The existence of multi-emissive peaks with large variation in the fluorescence intensities were established by 3D emission contour spectral studies. The probable location of the fluorophore in a heterogeneous environment was further ascertained by constructing a time-resolved emission spectrum (TRES) and time-resolved area normalized emission spectrum (TRANES) plots. Fluorescence spectral technique is used as an analytical tool in understanding the photophysical properties of a water soluble complex food hydrocolloid containing an intrinsic fluorophore located in a multiple environment is illustrated. - Highlights: • The Manuscript deals with the steady state absorption, emission, fluorescence lifetime and time-resolved emission spectrum studies of Gum Arabic in aqueous medium at various pH conditions. • The fluorescence emanates from the tyrosine amino acid present in GA. • Change in pH results in marked variation in the fluorescence spectral properties of tyrosine. • Fluorescence spectral techniques are employed as a tool in establishing the

  17. Plant-crafted starches for bioplastics production.

    Science.gov (United States)

    Sagnelli, Domenico; Hebelstrup, Kim H; Leroy, Eric; Rolland-Sabaté, Agnès; Guilois, Sophie; Kirkensgaard, Jacob J K; Mortensen, Kell; Lourdin, Denis; Blennow, Andreas

    2016-11-05

    Transgenically-produced amylose-only (AO) starch was used to manufacture bioplastic prototypes. Extruded starch samples were tested for crystal residues, elasticity, glass transition temperature, mechanical properties, molecular mass and microstructure. The AO starch granule crystallinity was both of the B- and Vh-type, while the isogenic control starch was mainly A-type. The first of three endothermic transitions was attributed to gelatinization at about 60°C. The second and third peaks were identified as melting of the starch and amylose-lipid complexes, respectively. After extrusion, the AO samples displayed Vh- and B-type crystalline structures, the B-type polymorph being the dominant one. The AO prototypes demonstrated a 6-fold higher mechanical stress at break and 2.5-fold higher strain at break compared to control starch. Dynamic mechanical analysis showed a significant increase in the storage modulus (E') for AO samples compared to the control. The data support the use of pure starch-based bioplastics devoid of non-polysaccharide fillers. Copyright © 2016 Elsevier Ltd. All rights reserved.

  18. Slowing the Starch Digestion by Structural Modification through Preparing Zein/Pectin Particle Stabilized Water-in-Water Emulsion.

    Science.gov (United States)

    Chen, Jia-Feng; Guo, Jian; Zhang, Tao; Wan, Zhi-Li; Yang, Juan; Yang, Xiao-Quan

    2018-04-25

    Slowing the digestion of starch is one of the dominant concerns in the food industry. A colloidal structural modification strategy for solving this problem was proposed in this work. Due to thermodynamic incompatibility between two biopolymers, water/water emulsion of waxy corn starch (WCS) droplets dispersed in a continuous aqueous guar gum (GG) was prepared, and zein particles (ZPs), obtained by antisolvent precipitation and pectin modification, were used as stabilizer. As the ratio of zein to pectin in the particles was 1:1, their wetting properties in the two polysaccharides were similar, which made them accumulate at the interface and cover the WCS-rich droplets. The analysis of digestibility curves indicated that a rapid (rate constant k 1 : 0.145 min -1 ) and a slow phase ( k 2 : 0.022 min -1 ) existed during WCS digestion. However, only one slow phase ( k 2 : 0.019 min -1 ) was found in the WCS/GG emulsion, suggesting that this structure was effective in slowing starch digestion.

  19. Reduced starch granule number per chloroplast in the dpe2/phs1 mutant is dependent on initiation of starch degradation.

    Science.gov (United States)

    Malinova, Irina; Fettke, Joerg

    2017-01-01

    An Arabidopsis double knock-out mutant lacking cytosolic disproportionating enzyme 2 (DPE2) and the plastidial phosphorylase (PHS1) revealed a dwarf-growth phenotype, reduced starch content, an uneven distribution of starch within the plant rosette, and a reduced number of starch granules per chloroplast under standard growth conditions. In contrast, the wild type contained 5-7 starch granules per chloroplast. Mature and old leaves of the double mutant were essentially starch free and showed plastidial disintegration. Several analyses revealed that the number of starch granules per chloroplast was affected by the dark phase. So far, it was unclear if it was the dark phase per se or starch degradation in the dark that was connected to the observed decrease in the number of starch granules per chloroplast. Therefore, in the background of the double mutant dpe2/phs1, a triple mutant was generated lacking the initial starch degrading enzyme glucan, water dikinase (GWD). The triple mutant showed improved plant growth, a starch-excess phenotype, and a homogeneous starch distribution. Furthermore, the number of starch granules per chloroplast was increased and was similar to wild type. However, starch granule morphology was only slightly affected by the lack of GWD as in the triple mutant and, like in dpe2/phs1, more spherical starch granules were observed. The characterized triple mutant was discussed in the context of the generation of starch granules and the formation of starch granule morphology.

  20. TECHNOLOGY OF THERMOPLASTIC STARCH PRODUCTION

    Directory of Open Access Journals (Sweden)

    N. D. Lukin

    2015-01-01

    Full Text Available In recent years, the manufacturing of bio-recyclable polymer products, which production and consumption has become an efficient way to protect environment from solid wastes in different countries of the world. The issue of environmental protection becomes global and the rapid growth of synthetic plastics application in many industries is a serious concern. There is a important task to improve the quality, safety and durability of products as well as their utilization after the expiration period. One of the most acceptable ways to solve these issues is to produce biodegradable materials based on natural materials, which are not harmful for environment and human health. A very common and effective method to give biological degradability to synthetic polymers is to insert starch into polymer composition in combination with other ingredients.

  1. Effect of enzymatic depolymerization on physicochemical and rheological properties of guar gum.

    Science.gov (United States)

    Mudgil, Deepak; Barak, Sheweta; Khatkar, B S

    2012-09-01

    Depolymerization of guar gum using enzymatic hydrolysis was performed to obtain depolymerized guar gum having functional application as soluble dietary fiber. Enzymatic hydrolysis of guar gum significantly affected the physicochemical and rheological characteristics of guar gum. The depolymerized guar gum showed a significant increase in crystallinity index from 3.86% to 13.2% and flow behavior index from 0.31 to 1.7 as compared to native guar gum. Remarkable decrease in intrinsic viscosity and consistency index was also observed from 9 to 0.28 and 4.04 to 0.07, respectively. Results revealed that enzymatic hydrolysis of guar gum resulted in a polysaccharide with low degree of polymerization, viscosity and consistency which could make it useful for incorporation in food products as dietary fiber without affecting the rheology, consistency and texture of the products. Copyright © 2012 Elsevier Ltd. All rights reserved.

  2. Chewing gum and context-dependent memory effects: a re-examination.

    Science.gov (United States)

    Miles, Christopher; Johnson, Andrew J

    2007-03-01

    Two experiments re-examined whether chewing spearmint gum affects initial word learning and/or immediate recall for a word list. Both experiments failed to show effects of chewing gum at learning or recall, nor did they suggest that chewing gum produces a context-dependent memory effect. This was true when extraneous contextual cues at learning and recall were minimised (Experiment 2). Together, the data are inconsistent with [Wilkinson, L., Scholey, A. & Wesnes, K. (2002). Chewing gum selectively improves aspects of memory in healthy volunteers. Appetite, 38, 235-236.] claim that chewing gum aids immediate recall of visually presented words. Our results are consistent with [Baker, J. R., Bezance, J. B., Zellaby, E. & Aggleton, J. P. (2004). Chewing gum can produce context-dependent effects upon memory. Appetite, 43, 207-210.] finding that chewing gum of itself is not a sufficient condition to provoke context-dependent learning with immediate testing.

  3. Effects and after-effects of chewing gum on vigilance, heart rate, EEG and mood.

    Science.gov (United States)

    Allen, Andrew P; Jacob, Tim J C; Smith, Andrew P

    2014-06-22

    Research has shown that chewing gum improves attention, although the mechanism for this effect remains unclear. This study investigated the effects and after-effects of chewing gum on vigilance, mood, heart rate and EEG. Participants completed a vigilance task four times; at baseline, with or without chewing gum, and twice post-chewing. EEG alpha and beta power at left frontal and temporal lobes, subjective mood and heart rate were assessed. Chewing gum shortened reaction time and increased the rate of hits, although hits fell during the second post-chewing task. Chewing gum heightened heart rate, but only during chewing. Gum also increased beta power at F7 and T3 immediately post-chewing, but not following the post-chewing tasks. The findings show that chewing gum affects several different indicators of alertness. Copyright © 2014 Elsevier Inc. All rights reserved.

  4. Process for the production of starch and alcohol from substances containing starch

    Energy Technology Data Exchange (ETDEWEB)

    Smith, N B; McFate, H A; Eubanks, E M

    1969-01-01

    Almost complete extraction of starch from wheat, rice, maize, etc., is achieved more economically then by conventional processes. Starch-containing cereal is soaked, the magma is broken and the seed removed. The magma is then drained and separated into a liquid filtrate consisting of starch, gluten and fine fibers, and a solid residue made up of coarse fibers, husks and grit. The liquid filtrate is sieved to remove the fine fibers, and then centrifuged to obtain pure, gluten-free starch. The solid residue is treated with a mineral acid in a converter to give sugar, thus forming a material which is fermented and distilled to give alcohol.

  5. Starch Digestibility and Functional Properties of Rice Starch Subjected to Gamma Radiation

    Directory of Open Access Journals (Sweden)

    Luís Fernando Polesi

    2018-01-01

    Full Text Available This study investigated the effect of gamma radiation on the digestibility and functional properties of rice starch. Rice cultivars IRGA417 and IAC202 were used for isolation of starch by the alkaline method. Starch samples were irradiated with 1, 2 and 5 kGy doses of 60Co at a rate of 0.4 kGy/h. A control sample, which was not irradiated, was used for comparison. Irradiated and control starches were characterized by in vitro starch digestibility, total dietary fiber, color, water absorption index, water solubility index, syneresis, swelling factor, amylose leaching, pasting properties and gel firmness. Irradiations changed starch digestibility differently in either cultivar. Increasing radiation doses promoted increase in the color parameter b* (yellow, elevation in the capacity to absorb water, and solubility in water as well as the amylose leached from granules for both cultivars. Pasting properties showed a decrease that was proportional to the dose applied, caused by the depolymerization of starch molecules. Gel firmness of the starch from IAC202 was inversely proportional to the radiation dose applied, whereas for IRGA417, there was a reduction at 5 kGy dose. Rice starches can be modified by irradiation to exhibit different functional characteristics and they can be used by the food industries in products such as soups, desserts, flans, puddings and others.

  6. Dilute solution properties of canary seed (Phalaris canariensis) starch in comparison to wheat starch.

    Science.gov (United States)

    Irani, Mahdi; Razavi, Seyed M A; Abdel-Aal, El-Sayed M; Hucl, Pierre; Patterson, Carol Ann

    2016-06-01

    Dilute solution properties of an unknown starch are important to understand its performance and applications in food and non-food industries. In this paper, rheological and molecular properties (intrinsic viscosity, molecular weight, shape factor, voluminosity, conformation and coil overlap parameters) of the starches from two hairless canary seed varieties (CO5041 & CDC Maria) developed for food use were evaluated in the dilute regime (Starch dispersions in DMSO (0.5g/dl)) and compared with wheat starch (WS). The results showed that Higiro model is the best among five applied models for intrinsic viscosity determination of canary seed starch (CSS) and WS on the basis of coefficient of determination (R(2)) and root mean square error (RMSE). WS sample showed higher intrinsic viscosity value (1.670dl/g) in comparison to CSS samples (1.325-1.397dl/g). Berry number and the slope of master curve demonstrated that CSS and WS samples were in dilute domain without entanglement occurrence. The shape factor suggested spherical and ellipsoidal structure for CO5041 starch and ellipsoidal for CDC Maria starch and WS. The molecular weight, coil radius and coil volume of CSSs were smaller than WS. The behavior and molecular characterization of canary seed starch showed its unique properties compared with wheat starch. Copyright © 2016 Elsevier B.V. All rights reserved.

  7. Partially hydrolyzed guar gum as a potential prebiotic source.

    Science.gov (United States)

    Mudgil, Deepak; Barak, Sheweta; Patel, Ami; Shah, Nihir

    2018-06-01

    Guar galactomannan was enzymatically hydrolyzed to obtain partially hydrolyzed guar gum which can be utilized as prebiotic source. In present study, growth of probiotics (Lactic Acid Bacteria strains) were studied with glucose, partially hydrolyzed guar gum and native guar gum. All the six strains were galactose &/or mannose positive using the API CHl 50 test. Almost all these strains showed an ability to assimilate partially hydrolyzed guar gum with respect to increase in optical density and viable cell count with concomitant decrease in the pH of the growth medium. Streptococcus thermophilus MD2 exhibited higher growth (7.78 log cfu/ml) while P. parvulus AI1 showed comparatively less growth (7.24 log cfu/ml) as compared to used lactobacillus and Weissella strains. Outcomes of the current study suggest that partially hydrolyzed guar can be considered as potential prebiotic compound that may further stimulate the growth of potentially probiotic bacteria or native gut microflora. Copyright © 2018 Elsevier B.V. All rights reserved.

  8. Radiation induced degradation of xanthan gum in aqueous solution

    Science.gov (United States)

    Hayrabolulu, Hande; Demeter, Maria; Cutrubinis, Mihalis; Güven, Olgun; Şen, Murat

    2018-03-01

    In our previous study, we have investigated the effect of gamma rays on xanthan gum in the solid state and it was determined that dose rate was an important factor effecting the radiation degradation of xanthan gum. In the present study, in order to provide a better understanding of how ionizing radiation effect xanthan gum, we have investigated the effects of ionizing radiation on aqueous solutions of xanthan at various concentrations (0.5-4%). Xanthan solutions were irradiated with gamma rays in air, at ambient temperature, at different dose rates (0.1-3.3-7.0 kGy/h) and doses (2.5-50 kGy). Change in their molecular weights was followed by size exclusion chromatography (SEC). Chain scission yield (G(S)), and degradation rate constants (k) were calculated. It was determined that, solution concentration was a factor effecting the degradation chemical yield and degradation rate of xanthan gum. Chain scission reactions were more effective for lower solution concentrations.

  9. Gellan gum fluid gels for topical administration of diclofenac.

    Science.gov (United States)

    Mahdi, Mohammed H; Conway, Barbara R; Mills, Thomas; Smith, Alan M

    2016-12-30

    Diclofenac topical formulations are often preferred for drug administration to patients who experience serious GIT problems. Absorption of the drug through the skin, however, can be challenging due to the natural protective feature of the stratum corneum (SC). In this article, fluid gels prepared from gellan gum were explored as a topical drug delivery vehicle. Rheological analysis of the formulations showed that it was possible to produce a topical gel with a viscosity and the mechanical strength similar to that of the commercially available Voltaren ® gel using 1% w/w of a 50:50 low acyl/high acyl (LA/HA) gellan blend. Soft-tribology was used to assess the lubrication properties of gellan fluid gels. The lubrication of the gellan gum fluid gel formulations at high rubbing speeds was similar to the lubrication of the Voltaren ® gel. The use of gellan gum dramatically increased skin permeation of diclofenac when compared with the commercially available formulation and could be controlled by changing the gellan gum concentration and/or sodium ion concentration in the formulation. This study highlights the potential use of fluid gels that can be easily tuned to have physical properties suitable for topical formulations with the added advantage of increasing drug permeation. Copyright © 2016 Elsevier B.V. All rights reserved.

  10. Cetirizine release from cyclodextrin formulated compressed chewing gum

    DEFF Research Database (Denmark)

    Stojanov, Mladen; Larsen, Kim Lambertsen

    2012-01-01

    release patterns, but with variations in the total amount released. Chewing gum formulated with cetirizine alone, demonstrated a release of 75% after 8 min of chewing. The presence of CDs resulted in increased cetirizine release. The analysis of variance (ANOVA) demonstrated that parameters with the most...... the statistical analysis (ANOVA) demonstrated significance in the release (P

  11. Cashew gum and gelatin blend for food packaging application

    Science.gov (United States)

    Cashew gum (CG) and gelatin (G) films were developed using the casting method and response surface methodology. The objective was produce packaging films from CG/G blends that exhibit effective barrier properties. A study of zeta potential versus pH was first carried out to determine the isoelectric...

  12. Ask a Periodontist (Frequently Asked Questions about Gum Disease)

    Science.gov (United States)

    ... May Increase Lung Cancer Risk CDC Estimate: New Mexico, Hawaii Have Highest U.S. Incidence of Advanced Gum ... Finally, periodontists can be integral in the comprehensive planning of your oral care, along ... the costs of implants can often vary from urban to rural areas and will depend on how ...

  13. Grewia Gum 2: Mucoadhesive Properties of Compacts and Gels

    African Journals Online (AJOL)

    Erah

    Tragacanth, a plant gum, has been used as a bioadhesive polymer to promote dosage form residence time as well as to improve intimacy of contact with various absorptive surfaces of biological systems [3]. Several approaches have been used to evaluate in vitro interaction between mucin and mucoadhesive systems and ...

  14. Evaluation of the suspending properties of Cola acuminata gum on ...

    African Journals Online (AJOL)

    Calamine suspensions were formulated with CAG between the concentration range of 1 – 4 % w/v and compared with suspensions formulated with two standard suspending agents (tragacanth and acacia gums). Sedimentation volume, flow rate, rheology and redispersibility were used as evaluating parameters.

  15. Iron microencapsulation in gum tragacanth using solvent evaporation method.

    Science.gov (United States)

    Asghari-Varzaneh, Elham; Shahedi, Mohammad; Shekarchizadeh, Hajar

    2017-10-01

    In this study iron salt (FeSO 4 ·7H 2 O) was microencapsulated in gum tragacanth hydrogel using solvent evaporation method. Three significant parameters (ferrous sulfate content, content of gum tragacanth, and alcohol to mixture ratio) were optimized by response surface methodology to obtain maximum encapsulation efficiency. Ferrous sulfate content, 5%, content of gum tragacanth, 22%, and alcohol to mixture ratio, 11:1 was determined to be the optimum condition to reach maximum encapsulation efficiency. Microstructure of iron microcapsules was thoroughly monitored using scanning electron microscopy (SEM). The microphotographs indicated two distinct crystalline and amorphous structures in the microcapsules. This structure was confirmed by X-ray diffraction (XRD) pattern of microcapsules. Fourier transform infrared (FTIR) spectra of iron microcapsules identified the presence of iron in the tragacanth microcapsules. The average size of microcapsules was determined by particle size analyzer. Release assessment of iron in simulated gastric fluid showed its complete release in stomach which is necessary for its absorption in duodenum. However, the use of encapsulated iron in gum tragacanth in watery foods is rather recommended due to the fast release of iron in water. Copyright © 2017 Elsevier B.V. All rights reserved.

  16. Binding Properties Of A Polymeric Gum From Cola accuminata ...

    African Journals Online (AJOL)

    However all the tablets produced with 1 % w/w binder; Sodium carboxyl methyl cellulose (SCMC) and Cola accuminata failed the hardness test. Hardness increased while friability decreased as tablet binder concentration increased. However, the tablets produced with Cola accuminata gum had long disintegration times ...

  17. Effect of addition of different hydrocolloids on pasting, thermal, and rheological properties of cassava starch Efeito da adição de diferentes hidrocoloides sobre as propriedades de pasta, térmicas e reológicas do amido de mandioca

    Directory of Open Access Journals (Sweden)

    Tatiana Dias Leite

    2012-09-01

    Full Text Available Starches and gums are hydrocolloids frequently used in food systems to provide proper texture, moisture, and water mobility. Starch-gum interaction in food systems can change the starch granule swelling and its gelatinization and rheological properties. In this study, the effect of the addition of xanthan gum (XG, sodium carboxymethyl cellulose (SCMC, and carrageenan (CAR at the concentrations of the 0.15, 0.25, 0.35 and 0.45% (w/v on the pasting, thermal, and rheological properties of cassava starch was studied. The swelling power (SP and the scanning electron microscopy (SEM of the starch gels were also evaluated. The results obtained showed that xanthan gum (XG had a strong interaction with the cassava starch penetrating between starch granules causing increase in pasting viscosities, SP, storage and loss (G', and G", respectively modulus and reduction in the setback of the starch; sodium carboxymethyl cellulose (SCMC greatly increased the pasting viscosities, the SP, and the storage and loss (G', and G", respectively modulus of the starch-mixtures, mainly due to its greater capacity to hold water and not due to the interaction with cassava starch. Carrageenan (CAR did not change any of the starch properties since there was no interaction between this gum and cassava starch at the concentrations used.Amidos e gomas são hidrocoloides frequentemente usados em sistemas alimentícios com a finalidade de fornecer textura, umidade e mobilidade de água. A interação amido-goma em sistemas alimentícios pode alterar o inchamento do grânulo de amido e as suas propriedades de gelatinização e reológicas. Neste trabalho, o efeito da adição de goma xantana (GX, carboximetilcelulose sódica (CMC e carragena (CAR nas concentrações de 0,15, 0,25, 0,35 e 0,45% (p/v sobre as propriedades de pasta, térmicas e reológicas do amido de mandioca foi estudado. O Poder de inchamento (PI e a Microscopia Eletrônica de Varredura (MEV dos géis de amido tamb

  18. Production of modified starches by gamma irradiation

    International Nuclear Information System (INIS)

    Kang, Il-Jun; Byun, Myung-Woo; Yook, Hong-Sun; Bae, Chun-Ho; Lee, Hyun-Soo; Kwon, Joong-Ho; Chung, Cha-Kwon

    1999-01-01

    As a new processing method for the production of modified starch, gamma irradiation and four kinds of inorganic peroxides were applied to commercial corn starch. The addition of inorganic peroxides without gamma irradiation or gamma irradiation without the addition of inorganic peroxides effectively decreased initial viscosity, but did not sufficiently keep viscosity stable. The combination of adding ammonium persulfate (APS) and gamma irradiation showed the lowest initial viscosity and the best stability out of the tested four kinds of inorganic peroxides. Among the tested mixing methods of APS, soaking was found to be more effective than dry blending or spraying. Therefore, the production of modified starch with low viscosity as well as with sufficient viscosity stability became feasible by the control of gamma irradiation dose levels and the amount of added APS to starch

  19. Utilisation of sago starch for wound dressing

    International Nuclear Information System (INIS)

    Kamaruddin Hashim; Khairul Zaman Mohd Dahlan; Kamarudin Bahari

    2000-01-01

    Sago starch is utilized in Malaysia mainly for the purpose of food production. The purpose of the research is to diversify the use of sago starch for medical application particularly in development of hydrogel wound dressing. The sago starch is blending with water-soluble polymer such as polyvinyl pyrrolidone, polyvinyl alcohol and polyethylene oxide and irradiated with electron beam accelerator to form hydrogel. The parameters such gel strength, elasticity, swelling, gel fraction and tackiness have to be consider for this type of application. We also study the effect of adding additive such as carboxymethyl cellulose and polypropylene glycol into the system to enhance the property of sago starch hydrogel. Works on the use of chitosan in the blend have been performed, in order to prevent microbiological growth such as bacteria and fungi on the hydrogel. (author)

  20. Characterization of Digestion Resistance Sweet Potato Starch ...

    African Journals Online (AJOL)

    Purpose: To analyze the physicochemical properties and in vitro digestibility of sweet potato starchphosphodiester prepared using sodium trimetaphosphate. Methods: The physicochemical properties of sweet potato starch phosphodiester were analyzed by using infrared spectrometry (IR), differential scanning calorimetry ...

  1. Up-Scaling Production of Carboxymethyl Starch

    International Nuclear Information System (INIS)

    Mohd Hafiz Abdul Nasir; Zainon Othman; Kamaruddin Hashim; Siti Khadijah Abu Hadin; Nurul Nadia Shaaban

    2015-01-01

    Carboxymethyl starch (CMS) is a starch derivative formed by its reaction with sodium monochloroacetate which consist of OH-groups that are partially or completely replaced by ether substitution. Characteristic of CMSS defined by the degree of substitution (DS). DS is defined as the average number of substituents per anhydro glucose unit (AGU), the monomer unit of starch. The upgrading of CMSS production from 10L to 30L requires several experiments with different variable such as amount NaOH, amount of Sago Starch and reaction time. Each will give different DS. Quality control for the product cover moisture, viscosity and paste clarity. Therefore, SOP has been established to control the quality final product. (author)

  2. Evaluation of accelerated stability test conditions for medicated chewing gums.

    Science.gov (United States)

    Maggi, Lauretta; Conte, Ubaldo; Nhamias, Alain; Grenier, Pascal; Vergnault, Guy

    2013-10-01

    The overall stability of medicated chewing gums is investigated under different storage conditions. Active substances with different chemical stabilities in solid state are chosen as model drugs. The dosage form is a three layer tablet obtained by direct compression. The gum core contains the active ingredient while the external layers are formulated to prevent gum adhesion to the punches of the tableting machine. Two accelerated test conditions (40°C/75% RH and 30°C/65% RH) are performed for 6 months. Furthermore, a long-term stability test at room conditions is conducted to verify the predictability of the results obtained from the stress tests. Some drugs are stable in all the conditions tested, but other drugs, generally considered stable in solid dosage forms, have shown relevant stability problems particularly when stress test conditions are applied to this particular semi-solid dosage forms. For less stable drugs, the stress conditions of 40°C/75% RH are not always predictable of chewing gum stability at room temperature and may produce false negative; intermediate conditions, 30°C/65% RH, are more predictive for this purpose, the results of drug content found after 6 months at intermediate stress conditions and 12 months at room conditions are generally comparable. But the results obtained show that only long-term conditions stability tests gave consistent results. During aging, the semi solid nature of the gum base itself, may also influence the drug delivery rate during chewing and great attention should be given also to the dissolution stability.

  3. Naturalistic assessment of demand for cigarettes, snus, and nicotine gum.

    Science.gov (United States)

    Stein, Jeffrey S; Wilson, A George; Koffarnus, Mikhail N; Judd, Michael C; Bickel, Warren K

    2017-01-01

    Behavioral economic measures of demand provide estimates of tobacco product abuse liability and may predict effects of policy-related price regulation on consumption of existing and emerging tobacco products. In the present study, we examined demand for snus, a smokeless tobacco product, in comparison to both cigarettes and medicinal nicotine. We used both a naturalistic method in which participants purchased these products for use outside the laboratory, as well as laboratory-based self-administration procedures. Cigarette smokers (N = 42) used an experimental income to purchase their usual brand of cigarettes and either snus or gum (only one product available per session) across a range of prices, while receiving all products they purchased from one randomly selected price. In a separate portion of the study, participants self-administered these products during laboratory-based, progressive ratio sessions. Demand elasticity (sensitivity of purchasing to price) was significantly greater for snus than cigarettes. Elasticity for gum was intermediate between snus and cigarettes but was not significantly different than either. Demand intensity (purchasing unconstrained by price) was significantly lower for gum compared to cigarettes, with no significant difference observed between snus and cigarettes. Results of the laboratory-based, progressive ratio sessions were generally discordant with measures of demand elasticity, with significantly higher "breakpoints" for cigarettes compared to gum and no significant differences between other study products. Moreover, breakpoints and product purchasing were generally uncorrelated across tasks. Under naturalistic conditions, snus appears more sensitive to price manipulation than either cigarettes or nicotine gum in existing smokers.

  4. Radiation sterilization of potato starch and Sedonik

    International Nuclear Information System (INIS)

    Tashmetov, M.Yu.; Ismatov, N.B.; Saidov, R.P. et al.

    2016-01-01

    The raw material of pharmaceutical preparations potato starch and sedative means of Sedonik are sterilized at the electron's accelerator Electronics U-003. It is established that at 20.3 kGy absorbed dose and electron's energy 3 - 5 MeV the results of microbiological analysis showed sterility of potato starch and Sedonik and correspondence of their physical-optical properties to the requirements of normative documents. (authors)

  5. Resistant starch: an indigestible fraction of foods

    Directory of Open Access Journals (Sweden)

    Saura Calixto, F.

    1991-06-01

    Full Text Available Resistant starch (RS, the dietary starch that scape digestion in the small intestine, can yields up to 20% of the starch in cereal and legume products. Several fractions contribute to the total RS of foods: retrograded amylose, starch inaccessible to digestive enzymes because of mechanical barriers, chemically modified starch fragments, undigested starch due to α-amylase inhibitors and starch complexed with other food components. RS is formed in products processed following heat treatments (baking, extrusion, autoclaving, etc.. RS produces significant fecal bulking and is partially fermentable by anaerobic bacteria of the colon. On the other hand, the relation of resistant starch with the glucose and insulin response in human subjects is an important nutritional effect. RS analytical methods are reported.

    El almidón resistente (RS, fracción de almidón de la dieta que no es digerido en el intestino delgado, puede alcanzar hasta un 20% del almidón en productos derivados de cereales y legumbres. Varias fracciones contribuyen al contenido total de almidón resistente: amilosa retrogradada, almidón inaccesible físicamente a los enzimas digestivos, almidón indigestible debido a inhibición de α-amilasas y almidón complejado con otros constituyentes de los alimentos. El almidón resistente se forma en productos que han sufrido tratamientos térmicos (panificación, extrusión, autoclave, etc. El RS aumenta el volumen de heces y es fermentado parcialmente en el colon por bacterias anaeróbicas. Igualmente, está relacionado con los niveles de glucosa en sangre y la respuesta de insulina en humanos. Se describen los métodos analíticos para su determinación.

  6. Biodegradable starch-based polymeric materials

    Science.gov (United States)

    Suvorova, Anna I.; Tyukova, Irina S.; Trufanova, Elena I.

    2000-05-01

    The effects of low-molecular-weight additives, temperature and mechanical action on the structure and properties of starch are discussed. Special attention is given to mixtures of starch with synthetic polymers, e.g., co-polymers of ethylene with vinyl acetate, vinyl alcohol, acrylic acid, cellulose derivatives and other natural polymers. These mixtures can be used in the development of novel environmentally safe materials (films, coatings, packaging materials) and various articles for short-term use. The bibliography includes 105 references.

  7. Influence of phosphate esters on the annealing properties of starch

    DEFF Research Database (Denmark)

    Wischmann, Bente; Muhrbeck, Per

    1998-01-01

    The effects of annealing on native potato, waxy maize, and phosphorylated waxy maize starches were compared. Phosphorylated waxy maize starch responded to annealing in a manner between that of the naturally phosphorylated potato starch and that of the native waxy maize starch. The gelatinisation...... end-point temperature was increased, whereas in the native waxy maize it was decreased. On the other hand, the onset temperature change was much larger in potato starch than in the two waxy maize starches. Steeping also yielded intermediate effects on the phosphorylated waxy maize starch....... It was concluded that the phosphate groups have similar effects as they do in the native, naturally phosphorylated potato starch, although the substitution pattern is not entirely the same in the artificially phosphorylated starch....

  8. Engineering Potato Starch with a Higher Phosphate Content.

    Directory of Open Access Journals (Sweden)

    Xuan Xu

    Full Text Available Phosphate esters are responsible for valuable and unique functionalities of starch for industrial applications. Also in the cell phosphate esters play a role in starch metabolism, which so far has not been well characterized in storage starch. Laforin, a human enzyme composed of a carbohydrate-binding module and a dual-specificity phosphatase domain, is involved in the dephosphorylation of glycogen. To modify phosphate content and better understand starch (dephosphorylation in storage starch, laforin was engineered and introduced into potato (cultivar Kardal. Interestingly, expression of an (engineered laforin in potato resulted in significantly higher phosphate content of starch, and this result was confirmed in amylose-free potato genetic background (amf. Modified starches exhibited altered granule morphology and size compared to the control. About 20-30% of the transgenic lines of each series showed red-staining granules upon incubation with iodine, and contained higher phosphate content than the blue-stained starch granules. Moreover, low amylose content and altered gelatinization properties were observed in these red-stained starches. Principle component and correlation analysis disclosed a complex correlation between starch composition and starch physico-chemical properties. Ultimately, the expression level of endogenous genes involved in starch metabolism was analysed, revealing a compensatory response to the decrease of phosphate content in potato starch. This study provides a new perspective for engineering starch phosphate content in planta by making use of the compensatory mechanism in the plant itself.

  9. Starch Spherulites Prepared by a Combination of Enzymatic and Acid Hydrolysis of Normal Corn Starch.

    Science.gov (United States)

    Shang, Yaqian; Chao, Chen; Yu, Jinglin; Copeland, Les; Wang, Shuo; Wang, Shujun

    2018-06-13

    This paper describes a new method to prepare spherulites from normal corn starch by a combination of enzymatic (mixtures of α-amylase and amyloglucosidase) and acid hydrolysis followed by recrystallization of the hydrolyzed products. The resulting spherulites contained a higher proportion of chains with a degree of polymerization (DP) of 6-12 and a lower proportion of chains with DP of 25-36, compared to those of native starch. The spherulites had an even particle size of about 2 μm and a typical B-type crystallinity. The amounts of long- and short-range molecular order of double helices in starch spherulites were larger, but the quality of starch crystallites was poorer, compared to that of native starch. This study showed an efficient method for preparing starch spherulites with uniform granule morphology and small particle size from normal corn starch. The ratios of α-amylase and amyloglucosidase in enzymatic hydrolysis had little effect on the structure of the starch spherulites.

  10. Concerted suppression of all starch branching enzyme genes in barley produces amylose-only starch granules

    DEFF Research Database (Denmark)

    Carciofi, Massimiliano; Blennow, Andreas; Jensen, Susanne L

    2012-01-01

    to glucose and rapidly absorbed in the small intestine. But a portion of dietary starch, termed "resistant starch" (RS) escapes digestion and reaches the large intestine, where it is fermented by colonic bacteria producing short chain fatty acids (SCFA) which are linked to several health benefits. The RS...

  11. In vitro starch digestion correlates well with rate and extent of starch digestion in broiler chickens

    NARCIS (Netherlands)

    Weurding, R.E.; Veldman, R.; Veen, W.A.G.; Aar, van der P.J.; Verstegen, M.W.A.

    2001-01-01

    Current feed evaluation systems for poultry are based on digested components (fat, protein and nitrogen-free extracts). Digestible starch is the most important energy source in broiler chicken feeds and is part of the nitrogen-free extract fraction. Digestible starch may be predicted using an in

  12. Green starch conversions : Studies on starch acetylation in densified CO2

    NARCIS (Netherlands)

    Muljana, Henky; Picchioni, Francesco; Heeres, Hero J.; Janssen, Leon P. B. M.

    2010-01-01

    The acetylation of potato starch with acetic anhydride (AAH) and sodium acetate (NaOAc) as catalyst in densified CO2 was explored in a batch reactor setup. The effects of process variables such as pressure (6-9.8 MPa), temperature (40-90 degrees C), AAH to starch ratio (2-5 mol/mol AGU), NaOAc to

  13. Characterization of starch films containing starch nanoparticles: part 1: physical and mechanical properties.

    Science.gov (United States)

    Shi, Ai-Min; Wang, Li-Jun; Li, Dong; Adhikari, Benu

    2013-07-25

    We report, for the first time, the preparation method and characteristics of starch films incorporating spray dried and vacuum freeze dried starch nanoparticles. Physical properties of these films such as morphology, crystallinity, water vapor permeability (WVP), opacity, and glass transition temperature (Tg) and mechanical properties (strain versus temperature, strain versus stress, Young's modulus and toughness) were measured. Addition of both starch nanoparticles in starch films increased roughness of surface, lowered degree of crystallinity by 23.5%, WVP by 44% and Tg by 4.3°C, respectively compared to those of starch-only films. Drying method used in preparation of starch nanoparticles only affected opacity of films. The incorporation of nanoparticles in starch films resulted into denser films due to which the extent of variation of strain with temperature was much lower. The toughness and Young's modulus of films containing both types of starch nanoparticles were lower than those of control films especially at <100°C. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Effect of gamma irradiation on thermophysical properties of plasticized starch and starch surfactant films

    Science.gov (United States)

    Cieśla, Krystyna; Watzeels, Nick; Rahier, Hubert

    2014-06-01

    In this work the influence of gamma irradiation on the thermomechanical properties of the films formed in potato starch-glycerol and potato starch-glycerol-surfactant systems were examined by Dynamic Mechanical Analysis, DMA, and Differential Scanning Calorimetry, DSC, and the results were correlated to the amount of the volatile fraction in the films.

  15. The effect of chewing gum's flavor on salivary flow rate and pH.

    Science.gov (United States)

    Karami-Nogourani, Maryam; Kowsari-Isfahan, Raha; Hosseini-Beheshti, Mozhgan

    2011-12-01

    Chewing sugar-free gums is a convenient way to increase salivary flow. Salivary flow increases in response to both gustatory (taste) and mechanical (chewing) stimuli, and chewing gum can provide both of these stimuli. The aim of this study was to compare the effect of five different flavors of sugar-free chewing gum on the salivary flow rate (SFR) and pH. Fifteen dental students volunteered at the same time on six consecutive days, to collect one minute unstimulated saliva. After five minutes, while some volunteers continued to collect only unstimulated saliva, the others asked to start chewing one of the five flavored gums randomly. The flavors were spearmint, cinnamon, watermelon, strawberry, and apple. The whole saliva was collected over time periods of 0 - 1, 1 - 3, and 3 - 6 minutes, and the SFR and pH were also measured. The data were subjected to pair t-test, repeated-measures analysis of variance, and Duncan tests. Compared to the unstimulated rate, all five different flavored gums significantly increased the SFR within six minutes. Although the flow rate peaked during the first minute of stimulation with all five products, it reduced gradually, but still remained above the unstimulated saliva, after six minutes. In the first minute, the strawberry-flavored gums showed the highest weight, yet, it only induced a significantly higher SFR compared to the cinnamon-flavored gums. During one to three minutes, strawberry and apple-flavored gums showed significantly higher SFR, respectively, compared to cinnamon-flavored gums. There were no significant differences in the flow rates elicited by each flavored gum through the three-to-six minute interval, although the spearmint-flavored gums induced slightly higher SFR. Only the spearmint and cinnamon-flavored gum significantly increased the salivary pH. Gum flavor can affect the SFR and special flavors may be advised for different individuals according to their oral conditions.

  16. Assessment of hupu gum for its carrier property in the design and evaluation of solid mixtures of poorly water soluble drug - rofecoxib.

    Science.gov (United States)

    Vadlamudi, Harini Chowdary; Raju, Y Prasanna; Asuntha, G; Nair, Rahul; Murthy, K V Ramana; Vulava, Jayasri

    2014-01-01

    There are no reports about the pharmaceutical applications of hupu gum (HG). Hence the present study was undertaken to test its suitability in the dissolution enhancement of poorly water soluble drug. Rofecoxib (RFB) was taken as model drug. For comparison solid mixtures were prepared with carriers such as poly vinyl pyrrolidone (PVP), sodium starch glycollate (SSG) and guar gum (GG). Physical mixing (PM), co-grinding (CG), kneading (KT) and solvent evaporation (SE) techniques were used to prepare the solid mixtures, using all the carriers in different carrier and drug ratios. The solid mixtures were characterized by powder X-ray diffraction (XRD) and Fourier-transformed infrared spectroscopy (FTIR). There was a significant improvement in the dissolution rate of solid mixtures of HG, when compared with the solid mixtures of other carriers. There was an increase in dissolution rate with increase in concentration of HG upto 1:1 ratio of carrier and drug. No drug-carrier interaction was found by FTIR studies. XRD studies indicated reduction in crystallinity of the drug with increase in HG concentration. Hence HG could be a useful carrier for the dissolution enhancement of poorly water soluble drugs.

  17. Effect of starch types on properties of biodegradable polymer based on thermoplastic starch process by injection molding technique

    Directory of Open Access Journals (Sweden)

    Yossathorn Tanetrungroj

    2015-04-01

    Full Text Available In this study effects of different starch types on the properties of biodegradable polymer based on thermoplastic starch (TPS were investigated. Different types of starch containing different contents of amylose and amylopectin were used, i.e. cassava starch, mungbean starch, and arrowroot starch. The TPS polymers were compounded and shaped using an internal mixer and an injection molding machine, respectively. It was found that the amount of amylose and amylopectin contents on native starch influence the properties of the TPS polymer. A high amylose starch of TPMS led to higher strength, hardness, degree of crystallization than the high amylopectin starch of TPCS. In addition, function group analysis by Fourier transforms infrared spectrophotometer, water absorption, and biodegradation by soil burial test were also examined.

  18. Effect of waxy rice flour and cassava starch on freeze-thaw stability of rice starch gels.

    Science.gov (United States)

    Charoenrein, Sanguansri; Preechathammawong, Nutsuda

    2012-10-01

    Repeatedly frozen and thawed rice starch gel affects quality. This study investigated how incorporating waxy rice flour (WF) and cassava starch (CS) in rice starch gel affects factors used to measure quality. When rice starch gels containing 0-2% WF and CS were subjected to 5 freeze-thaw cycles, both WF and CS reduced the syneresis in first few cycles. However CS was more effective in reducing syneresis than WF. The different composite arrangement of rice starch with WF or CS caused different mechanisms associated with the rice starch gel retardation of retrogradation, reduced the spongy structure and lowered syneresis. Both swollen granules of rice starch and CS caused an increase in the hardness of the unfrozen and freeze-thawed starch gel while highly swollen WF granules caused softer gels. These results suggested that WF and CS were effective in preserving quality in frozen rice starch based products. Copyright © 2012 Elsevier Ltd. All rights reserved.

  19. Retrogradation of Maize Starch after High Hydrostatic Pressure Gelation: Effect of Amylose Content and Depressurization Rate

    KAUST Repository

    Yang, Zhi; Swedlund, Peter; Gu, Qinfen; Hemar, Yacine; Chaieb, Saharoui

    2016-01-01

    High hydrostatic pressure (HHP) has been employed to gelatinize or physically modify starch dispersions. In this study, waxy maize starch, normal maize starch, and two high amylose content starch were processed by a HHP of the order of 600 MPa

  20. High surface area starch products as filler-binder in direct compression tablets

    NARCIS (Netherlands)

    te Wierik, G.HP; Ramaker, J.S; Eissens, A.C; Bergsma, J; Arends-Scholte, A.W.; Lerk, C.F

    Amylodextrin and modified starch products were prepared from amylose-free starches and from (amylose containing) potato starch by enzymatic degradation, followed by precipitation and filtration. The intermediate retrograded starch products were dehydrated by drying at room temperature or washing

  1. Physicochemical Properties of Gamma-Irradiated Corn Starch

    International Nuclear Information System (INIS)

    Lee, Y.J.; Lim, S.T.; Kim, S.Y.; Han, S.M.; Kim, H.M.; Kang, I.J.

    2006-01-01

    Structural modification of corn starch by gamma irradiation was evaluated for under dry conditions at varied intensities from 0 to 40 kGy. Under scanning electron microscopy, the granule shape of corn starch was not significantly affected by the irradiation up to 40 kGy. In addition, X-ray diffraction and melting patterns of the irradiated starches were similar to those of the native starch, indicating that crystalline regions in the starch granules were not changed by irradiation. However, the pattern of gel permeation column chromatography showed a significant increase in partial hydrolysis of gamma irradiated starch samples

  2. Degradation of corn starch under the influence of gamma irradiation

    International Nuclear Information System (INIS)

    El Saadany, R.M.A.; El Saadany, F.M.; Foda, Y.H.

    1976-01-01

    Irradiation of corn (maize) starch with different doses of gamma irradiation ranging from 1 x 10 5 rad to 1 x 10 6 rad resulted in the increase of starch acidity and reducing power. Molecular degradation was observed as a result of marked decrease in starch viscosity and intinsic viscosity as well as swelling capacity. The gelatinization time and temperature of the irradiated starch became shorter than in the control sample. Internal changes in the irradiated starch occured as a result of lowering the number of glucose unit per segment in the irradiated starch molecules. All changes were proportional to the doses of gamma irradiation used. (orig.) [de

  3. Impact of pressure on physicochemical properties of starch dispersions

    KAUST Repository

    Yang, Zhi; Chaib, Sahraoui; Gu, Qinfen; Hemar, Yacine

    2016-01-01

    High hydrostatic pressure (HHP) can be employed as a non-thermal sterilization technique in the food industry while inducing structure and physicochemical changes of the food macromolecules like starch. The effect of HHP on starch depends on various factors including starch type and concentration, pressurization temperature, time, and suspending media. In this review, we summarize the influence of HHP on the structure, gelatinization, retrogradation, and modification of starches from different botanical origins. Suggestions for future research are provided to better understand the mechanism of HHP on starch, and on how HHP can be used in the starch industry. © 2016 Elsevier Ltd.

  4. Degradation of corn starch under the influence of gamma irradiation

    Energy Technology Data Exchange (ETDEWEB)

    El Saadany, R M.A.; El Saadany, F M; Foda, Y H

    1976-01-01

    Irradiation of corn (maize) starch with different doses of gamma irradiation ranging from 1 x 10/sup 5/ rad to 1 x 10/sup 6/ rad resulted in the increase of starch acidity and reducing power. Molecular degradation was observed as a result of marked decrease in starch viscosity and intinsic viscosity as well as swelling capacity. The gelatinization time and temperature of the irradiated starch became shorter than in the control sample. Internal changes in the irradiated starch occured as a result of lowering the number of glucose unit per segment in the irradiated starch molecules. All changes were proportional to the doses of gamma irradiation used.

  5. The future of starch bioengineering: GM microorganisms or GM plants?

    DEFF Research Database (Denmark)

    Hebelstrup, Kim; Sagnelli, Domenico; Blennow, Andreas

    2015-01-01

    , tubers and cereal grains to provide a GM crop as an alternative to the use of enzymes from GM microorganisms. We here discuss these techniques in relation to important structural features and modifications of starches such as: starch phosphorylation, starch hydrolysis, chain transfer/branching and novel...... concepts of hybrid starch-based polysaccharides. In planta starch bioengineering is generally challenged by yield penalties and inefficient production of the desired product. However, in some situations, GM crops for starch bioengineering without deleterious effects have been achieved....

  6. Impact of pressure on physicochemical properties of starch dispersions

    KAUST Repository

    Yang, Zhi

    2016-09-02

    High hydrostatic pressure (HHP) can be employed as a non-thermal sterilization technique in the food industry while inducing structure and physicochemical changes of the food macromolecules like starch. The effect of HHP on starch depends on various factors including starch type and concentration, pressurization temperature, time, and suspending media. In this review, we summarize the influence of HHP on the structure, gelatinization, retrogradation, and modification of starches from different botanical origins. Suggestions for future research are provided to better understand the mechanism of HHP on starch, and on how HHP can be used in the starch industry. © 2016 Elsevier Ltd.

  7. Concerted suppression of all starch branching enzyme genes in barley produces amylose-only starch granules

    DEFF Research Database (Denmark)

    Carciofi, Massimiliano; Blennow, Per Gunnar Andreas; Jensen, Susanne Langgård

    2012-01-01

    is preferentially derived from amylose, which can be increased by suppressing amylopectin synthesis by silencing of starch branching enzymes (SBEs). However all the previous works attempting the production of high RS crops resulted in only partly increased amylose-content and/or significant yield loss. Results...... In this study we invented a new method for silencing of multiple genes. Using a chimeric RNAi hairpin we simultaneously suppressed all genes coding for starch branching enzymes (SBE I, SBE IIa, SBE IIb) in barley (Hordeum vulgare L.), resulting in production of amylose-only starch granules in the endosperm...... yield in a living organism. This was achieved by a new method of simultaneous suppression of the entire complement of genes encoding starch branching enzymes. We demonstrate that amylopectin is not essential for starch granule crystallinity and integrity. However the slower initial growth of shoots from...

  8. Effects of water on starch-g-polystyrene and starch-g-poly(methyl acrylate) extrudates

    International Nuclear Information System (INIS)

    Henderson, A.M.; Rudin, A.

    1982-01-01

    Polystyrene and poly(methyl acrylate) were grafted onto wheat starch by gamma radiation and chemical initiation, respectively. The respective percent add-on values were 46 and 45; 68% of the polystyrene formed was grafted to starch, and corresponding proportion of poly(methyl acrylate) was 41%. The molecular weight distributions of the homopolymer and graft portions were characterized, and extrusion conditions were established for production of ribbon samples of starch-g-PS and starch-g-PMA. Both copolymer types were considerably weakened by soaking in water, and this effect was more immediate and drastic for starch-g-poly(methyl acrylate). Both graft copolymers regained their original tensile strengths on drying, but the poly(methyl acrylate) specimens did not recover their original unswollen dimensions and retained high breaking elongations characteristic of soaked specimens. Tensile and dynamic mechanical properties of extruded and molded samples of both graft polymers are reported, and plasticizing effects of water are summarized

  9. Swelling Kinetics of Waxy Maize Starch

    Science.gov (United States)

    Desam, Gnana Prasuna Reddy

    Starch pasting behavior greatly influences the texture of a variety of food products such as canned soup, sauces, baby foods, batter mixes etc. The annual consumption of starch in the U.S. is 3 million metric tons. It is important to characterize the relationship between the structure, composition and architecture of the starch granules with its pasting behavior in order to arrive at a rational methodology to design modified starch of desirable digestion rate and texture. In this research, polymer solution theory was applied to predict the evolution of average granule size of starch at different heating temperatures in terms of its molecular weight, second virial coefficient and extent of cross-link. Evolution of granule size distribution of waxy native maize starch when subjected to heating at constant temperatures of 65, 70, 75, 80, 85 and 90 C was characterized using static laser light scattering. As expected, granule swelling was more pronounced at higher temperatures and resulted in a shift of granule size distribution to larger sizes with a corresponding increase in the average size by 100 to 120% from 13 mum to 25-28 mum. Most of the swelling occurred within the first 10 min of heating. Pasting behavior of waxy maize at different temperatures was also characterized from the measurements of G' and G" for different heating times. G' was found to increase with temperature at holding time of 2 min followed by its decrease at larger holding times. This behavior is believed to be due to the predominant effect of swelling at small times. However, G" was insensitive to temperature and holding times. The structure of waxy maize starch was characterized by cryoscanning electron microscopy. Experimental data of average granule size vs time at different temperatures were compared with model predictions. Also the Experimental data of particle size distribution vs particle size at different times and temperatures were compared with model predictions.

  10. Effects of cooking methods and starch structures on starch hydrolysis rates of rice.

    Science.gov (United States)

    Reed, Michael O; Ai, Yongfeng; Leutcher, Josh L; Jane, Jay-lin

    2013-07-01

    This study aimed to understand effects of different cooking methods, including steamed, pilaf, and traditional stir-fried, on starch hydrolysis rates of rice. Rice grains of 3 varieties, japonica, indica, and waxy, were used for the study. Rice starch was isolated from the grain and characterized. Amylose contents of starches from japonica, indica, and waxy rice were 13.5%, 18.0%, and 0.9%, respectively. The onset gelatinization temperature of indica starch (71.6 °C) was higher than that of the japonica and waxy starch (56.0 and 56.8 °C, respectively). The difference was attributed to longer amylopectin branch chains of the indica starch. Starch hydrolysis rates and resistant starch (RS) contents of the rice varieties differed after they were cooked using different methods. Stir-fried rice displayed the least starch hydrolysis rate followed by pilaf rice and steamed rice for each rice variety. RS contents of freshly steamed japonica, indica, and waxy rice were 0.7%, 6.6%, and 1.3%, respectively; those of rice pilaf were 12.1%, 13.2%, and 3.4%, respectively; and the stir-fried rice displayed the largest RS contents of 15.8%, 16.6%, and 12.1%, respectively. Mechanisms of the large RS contents of the stir-fried rice were studied. With the least starch hydrolysis rate and the largest RS content, stir-fried rice would be a desirable way of preparing rice for food to reduce postprandial blood glucose and insulin responses and to improve colon health of humans. © 2013 Institute of Food Technologists®

  11. Effects of starch synthase IIa gene dosage on grain, protein and starch in endosperm of wheat.

    Science.gov (United States)

    Konik-Rose, Christine; Thistleton, Jenny; Chanvrier, Helene; Tan, Ihwa; Halley, Peter; Gidley, Michael; Kosar-Hashemi, Behjat; Wang, Hong; Larroque, Oscar; Ikea, Joseph; McMaugh, Steve; Regina, Ahmed; Rahman, Sadequr; Morell, Matthew; Li, Zhongyi

    2007-11-01

    Starch synthases (SS) are responsible for elongating the alpha-1,4 glucan chains of starch. A doubled haploid population was generated by crossing a line of wheat, which lacks functional ssIIa genes on each genome (abd), and an Australian wheat cultivar, Sunco, with wild type ssIIa alleles on each genome (ABD). Evidence has been presented previously indicating that the SGP-1 (starch granule protein-1) proteins present in the starch granule in wheat are products of the ssIIa genes. Analysis of 100 progeny lines demonstrated co-segregation of the ssIIa alleles from the three genomes with the SGP-1 proteins, providing further evidence that the SGP-1 proteins are the products of the ssIIa genes. From the progeny lines, 40 doubled haploid lines representing the eight possible genotypes for SSIIa (ABD, aBD, AbD, ABd, abD, aBd, Abd, abd) were characterized for their grain weight, protein content, total starch content and starch properties. For some properties (chain length distribution, pasting properties, swelling power, and gelatinization properties), a progressive change was observed across the four classes of genotypes (wild type, single nulls, double nulls and triple nulls). However, for other grain properties (seed weight and protein content) and starch properties (total starch content, granule morphology and crystallinity, granule size distribution, amylose content, amylose-lipid dissociation properties), a statistically significant change only occurred for the triple nulls, indicating that all three genes had to be missing or inactive for a change to occur. These results illustrate the importance of SSIIa in controlling grain and starch properties and the importance of amylopectin fine structure in controlling starch granule properties in wheat.

  12. The working mechanism of Starch and Diutan gum in cementations and limestone dispersions in presence of polykarboxilate ether superplasticizers

    NARCIS (Netherlands)

    Schmidt, W.; Brouwers, H.J.H.; Kühne, H.C.; Meng, B.

    2013-01-01

    Polysaccharides provide high potential to be used as rheology modifying admixtures in mineral binder systems for the construction industry such as concrete or mortar. Since superplasticizers have become state of technology, today, concrete is more and more adjusted to flowable consistencies. This

  13. Starch Granule Re-Structuring by Starch Branching Enzyme and Glucan Water Dikinase Modulation Affects Caryopsis Physiology and Metabolism

    DEFF Research Database (Denmark)

    Shaik, Shahnoor S.; Obata, Toshihiro; Hebelstrup, Kim H

    2016-01-01

    in starch granule morphology at maturity. The results demonstrate that decreasing the storage starch branching resulted in metabolic adjustments and re-directions, tuning to evade deleterious effects on caryopsis physiology and plant performance while only little effect was evident by increasing starch......Starch is of fundamental importance for plant development and reproduction and its optimized molecular assembly is potentially necessary for correct starch metabolism. Re-structuring of starch granules in-planta can therefore potentially affect plant metabolism. Modulation of granule micro...

  14. Starch Granule Re-Structuring by Starch Branching Enzyme and Glucan Water Dikinase Modulation Affects Caryopsis Physiology and Metabolism

    DEFF Research Database (Denmark)

    Shaik, Shahnoor S.; Obata, Toshihiro; Hebelstrup, Kim H

    2016-01-01

    Starch is of fundamental importance for plant development and reproduction and its optimized molecular assembly is potentially necessary for correct starch metabolism. Re-structuring of starch granules in-planta can therefore potentially affect plant metabolism. Modulation of granule micro...... in starch granule morphology at maturity. The results demonstrate that decreasing the storage starch branching resulted in metabolic adjustments and re-directions, tuning to evade deleterious effects on caryopsis physiology and plant performance while only little effect was evident by increasing starch...

  15. Physicochemical properties of black pepper (Piper nigrum) starch.

    Science.gov (United States)

    Zhu, Fan; Mojel, Reuben; Li, Guantian

    2018-02-01

    Black pepper (Piper nigrum) is among the most popular spices around the world. Starch is the major component of black pepper. However, little is known about functional properties of this starch. In this study, swelling, solubility, thermal properties, rheology, and enzyme susceptibility of 2 black pepper starches were studied and compared with those of maize starch. Pepper starch had lower water solubility and swelling power than maize starch. It had higher viscosity during pasting event. In dynamic oscillatory analysis, pepper starch had lower storage modulus. Thermal analysis showed that pepper starch had much higher gelatinization temperatures (e.g., conclusion temperature of 94°C) than maize starch. The susceptibility to α-amylolysis of pepper starch was not very different from that of maize starch. Overall, the differences in the physicochemical properties of the 2 pepper starches are non-significant. The relationships between structure (especially amylopectin internal molecular structure) and properties of starch components are highlighted. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Sulfomethylated graft copolymers of xanthan gum and polyacrylamide

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, I.W.; Empey, R.A.; Racciato, J.S.

    1978-08-08

    A water-soluble anionic graft copolymer of xanthan gum and polyacrylamide is described in which at least part of the amide function of the acrylamide portion of the copolymer is sulfomethylated and the xanthan gum portion of the copolymer is unreacted with formaldehyde. The copolymer is sulfomethylated by reaction with formaldehyde and sodium metabisulfite. The formaldehyde does not cause any appreciable cross-linking between hydroxyl groups of the xanthan moieties. The sulfomethylation of the acrylamido group takes place at temperatures from 35 to 70 C. The pH is 10 or higher, typically from 12 to 13. The degree of anionic character may be varied by adjusting the molar ratio of formaldehyde and sodium metabisulfite with respect to the copolymer. 10 claims.

  17. Rhythm and amplitude of rhythmic masticatory muscle activity during sleep in bruxers - comparison with gum chewing.

    Science.gov (United States)

    Matsuda, Shinpei; Yamaguchi, Taihiko; Mikami, Saki; Okada, Kazuki; Gotouda, Akihito; Sano, Kazuo

    2016-07-01

    The aim of this study was to elucidate characteristics of rhythmic masticatory muscle activity (RMMA) during sleep by comparing masseteric EMG (electromyogram) activities of RMMA with gum chewing. The parts of five or more consecutive phasic bursts in RMMA of 23 bruxers were analyzed. Wilcoxon signed-rank test for matched pairs and Spearman's correlation coefficient by the rank test were used for statistical analysis. Root mean square value of RMMA phasic burst was smaller than that during gum chewing, but correlates to that of gum chewing. The cycle of RMMA was longer than that of gum chewing due to the longer burst duration of RMMA, and variation in the cycles of RMMA was wider. These findings suggest that the longer but smaller EMG burst in comparison with gum chewing is one of the characteristics of RMMA. The relation between size of RMMA phasic bursts and gum chewing is also suggested.

  18. X-ray diffraction, IR spectroscopy and thermal characterization of partially hydrolyzed guar gum.

    Science.gov (United States)

    Mudgil, Deepak; Barak, Sheweta; Khatkar, B S

    2012-05-01

    Guar gum was hydrolyzed using cellulase from Aspergillus niger at 5.6 pH and 50°C temperature. Hydrolyzed guar gum sample was characterized using Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, X-ray diffraction, dilute solution viscometry and rotational viscometry. Viscometry analysis of native guar gum showed a molecular weight of 889742.06, whereas, after enzymatic hydrolysis, the resultant product had a molecular weight of 7936.5. IR spectral analysis suggests that after enzymatic hydrolysis of guar gum there was no major transformation of functional group. Thermal analysis revealed no major change in thermal behavior of hydrolyzed guar gum. It was shown that partial hydrolysis of guar gum could be achieved by inexpensive and food grade cellulase (Aspergillus niger) having commercial importance and utilization as a functional soluble dietary fiber for food industry. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Efficacy of baking soda-containing chewing gum in removing natural tooth stain.

    Science.gov (United States)

    Mankodi, S M; Conforti, N; Berkowitz, H

    2001-07-01

    A 14-week, double-blind, randomized clinical trial was conducted with 126 healthy volunteers to compare the efficacy of twice-daily use of 3 baking soda-containing chewing gums in removing natural tooth stain when used in conjunction with a program of regular oral hygiene. All 3 chewing gums significantly reduced extrinsic stain (P Baking Soda Gum (AHDC) reduced dental stain by 70.8%, compared to reductions of 71.9% and 65.3%, after use of 2 experimental gum formulations. Whitened appearance improved by 1.73 shade tabs using AHDC gum, and up to 2.49 shade tabs with the experimental formulations. These results suggest that the use of baking soda-containing gum after meals, in conjunction with good oral hygiene, can improve both extrinsic dental staining and the whitened appearance of teeth.

  20. Influence of tragacanth gum in egg white based bioplastics: Thermomechanical and water uptake properties.

    Science.gov (United States)

    López-Castejón, María Luisa; Bengoechea, Carlos; García-Morales, Moisés; Martínez, Inmaculada

    2016-11-05

    This study aims to extend the range of applications of tragacanth gum by studying its incorporation into bioplastics formulation, exploring the influence that different gum contents (0-20wt.%) exert over the thermomechanical and water uptake properties of bioplastics based on egg white albumen protein (EW). The effect of plasticizer nature was also evaluated through the modification of the water/glycerol ratio within the plasticizer fraction (fixed at 40wt.%). The addition of tragacanth gum generally yielded an enhancement of the water uptake capacity, being doubled at the highest content. Conversely, presence of tragacanth gum resulted in a considerable decrease in the bioplastic mechanical properties: both tensile strength and maximum elongation were reduced up to 75% approximately when compared to the gum-free system. Ageing of selected samples was also studied, revealing an important effect of storage time when tragacanth gum is present, possibly due to its hydrophilic character. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Preparation and characterization of tragacanth-locust bean gum edible blend films.

    Science.gov (United States)

    Mostafavi, Fatemeh Sadat; Kadkhodaee, Rassoul; Emadzadeh, Bahareh; Koocheki, Arash

    2016-03-30

    The present work introduces the structure and physicomechanical properties of a novel blend film made from binary solutions of gum tragacanth (GT) and locust bean gum (LBG) at different mixing ratios. Apparent viscosities and surface tensions of individual and blend gum solutions were also investigated. The viscosity data indicated that there was a distinct synergism between the two gums at all mixing ratios. FTIR spectra showed the existence of noncovalent intermolecular interactions between gums. The surface tensions of binary solutions were significantly lower than those of individual gums which is advantageous for coating applications. All films had homogenous and smooth surface morphology and their transparency, water vapour barrier and mechanical properties were improved by incorporating LBG in blend. The results of this study suggest that GT-LBG blend film, owing to its desirable properties, has the potential to be used as a new degradable food packaging material. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Compositional analysis and rheological characterization of gum tragacanth exudates from six species of Iranian Astragalus

    DEFF Research Database (Denmark)

    Balaghi, Sima; Mohammadifar, Mohammad Amin; Zargaraan, Azizollaah

    2011-01-01

    The sugar composition and viscoelastic behaviour of Iranian gum tragacanth exuded by six species of Astragalus was investigated at a concentration of 1.3% and varying ionic strength using a controlled shear-rate rheometer. Compositional analysis of the six species of gum tragacanth by high...... of Astragalus, and this variation led to interesting differences in functional properties. Rheological measurements performed on dispersions of the six species of gum tragacanth demonstrated viscoelastic properties. The mechanical spectra derived from strain sweep and frequency sweep measurements indicated...... that the different gum tragacanth dispersions had distinctive viscoelastic behaviours. Investigation of the viscoelastic properties of the different gum dispersions in the presence of NaCl revealed that the addition of NaCl could lead to slight to drastic decreases in the G′, G″ or η∗ values of the various gums...

  3. Enzymic conversion of starch to glucose

    Energy Technology Data Exchange (ETDEWEB)

    1964-08-19

    Corn is steeped in a SO/sub 2/ solution for 30 to 40 hours, coarsely ground, separated from the germ, and filtered. A 35% suspension of the germ-free corn, still containing fibers, hull, and gluten, is treated with Ca(OH)/sub 2/ to raise the pH to 6.5 to 7.0. A starch-liquifying enzyme is added and after a 2 hours treatment at 85/sup 0/ the liquefied starch is cooled to 60/sup 0/ and the pH is adjusted to 4.5 to 5.0 with H/sub 2/SO/sub 4/. A saccharifying enzyme is now added. After 40 to 81 hours, a raw glucose solution is obtained and is freed from fibers and gluten by filtration. The commercial starch-liquifying enzymes are designated HT-1000 and Neozyme 3 LC (liquid). The saccharifying enzymes are Diazyme or Diazyme L 30 (liquid). The solid enzymes are used at a level up to 0.1% by weight of the starch. Up to 100% conversion of starch into glucose is achieved.

  4. Carboxy methylation of cashew nut tree exudate gum

    International Nuclear Information System (INIS)

    Silva, Durcilene A. da; Paula, Regina C.M.

    2001-01-01

    Anacardium occidentale exudate polysaccharide was carboxymethylated with monochloroacetic acid. The samples were characterized by NMR, solution viscometry, GPC and thermal analysis. Carboxymethylated cashew gum (CMGC) with a degree of substitution between 0,1-0,16 was obtained. Solution viscometry and GPC analysis showed that polymer molar mass degradation occurred. Sample with higher DS shows higher peak molar mass, intrinsic viscosity and thermal stability. NMR spectrum indicated that the carboxy methylation reaction occurs preferentially in C-6 of galactose residue. (author)

  5. Enhancement of electrical conductivity in the Gum Arabica complex

    International Nuclear Information System (INIS)

    Pradhan, Sourav S.; Sarkar, A.

    2009-01-01

    Gum Arabica is a natural biopolymer obtained from plant Acacia Arabica. In this present study the electro-active nature of its complex has been investigated. The complexes were developed using pure Gum Arabica and pure Citric acid by the sol-gel process. The scope of complex formation has been investigated and their natures were examined experimentally. The experiments which were carried out in this work are namely d.c V-I characteristics, d.c Arrhenius, ion transference number measurement, UV-VIS and IR photo-absorption. Solid specimen of the complex at various concentration of Citric acid has been developed for d.c experiments and adequate specimens were also developed for UV-VIS experiment. The result of d.c V-I characteristics on specimens at different Citric acid concentrations shows that d.c conductivity increases with concentration of the acid. The said enhancement is observed to be about 100 times that of pure hosts. The ion transference number measurement shows that the total conductivity increases with external acid concentration of which d.c conductivity enhance many times compared to that of ionic part. The result from d.c Arrhenius study shows that electro-thermal activation energy decreases with increasing acid concentration leading to enhancement of electronic conductivity of the complex. The result of UV-VIS study confirms the formation of the acid complex of Gum Arabica. The nature of photo-absorption indicates very clearly that main absorption region shows gradual shifts towards longer wavelength with increase of acid concentration. The result of FTIR absorption shows the structural concepts of electro-activity and complex formation indication of pure Gum Arabica. The overall analysis shows that the electro-activity of the mentioned biopolymer may be tailored.

  6. Effect of irradiation on functional properties of Gum Tragacanth

    Directory of Open Access Journals (Sweden)

    Neda Mollakhalili meybodi

    2017-03-01

    Full Text Available Background and objective: irradiation is a physical treatment in which products are exposed to ionized radiation such as gamma and x rays to improve the security and quality. Hydrocolloids are components that are used in food science to improve texture properties. Exposing to irradiation treatment may change structural and functional properties. By regard to the importance of irradiation on decontaminating of hydrocolloids in food application, the aim of this study is studying the effect of irradiation at different doses on functional properties of Gum Tragacanth in food application. Material and methods: effect of irradiation treatment was studied on the rheological properties, zeta potential, particle size distribution and surface tension of dispersion systems contained 0/5% w/ w gum tragacanth that is irradiated at different doses (0, 0.75. 3, 5 kGy. The effect of irradiation on rheological properties was monitored by rheometer. In order to monitor the effect of irradiation treatment on particle size distribution, zeta potential and surface tension, particle sizer, Brookhaven zeta plus and tensiometer sere used respectively. All treatments were performed three times and the data were analyzed by one way ANOVA. Significant differences between means were identified (P values < 0.05 using Duncan test. Results: Irradiation, change rheologiacal properties and particle size distribution of dispersion contained gum tragacanth. Irradiation treatment up to 0.75 kGy increase zeta potential, but irradiating at higher doses decrease it again. Results of studying parameters showed that irradiation changes the functional properties by affecting on structure. These changes depend on irradiation dose Conclusion: Gum tragacanth irradiation may improve the functional properties by affecting on structure.

  7. Molecular structure, functionality and applications of oxidized starches: A review.

    Science.gov (United States)

    Vanier, Nathan Levien; El Halal, Shanise Lisie Mello; Dias, Alvaro Renato Guerra; da Rosa Zavareze, Elessandra

    2017-04-15

    During oxidation, the hydroxyl groups of starch molecules are first oxidized to carbonyl groups, then to carboxyl groups. The contents of the carbonyl and carboxyl groups in a starch molecule therefore indicate the extent of starch oxidation. The mechanisms of starch oxidation with different oxidizing agents, including sodium hypochlorite, hydrogen peroxide, ozone and sodium periodate, are described in this review. The effects of these oxidizing agents on the molecular, physicochemical, thermal, pasting and morphological properties of starch are described as well. In addition, the main industrial applications of oxidized starches are presented. The present review is important for understanding the effects of oxidation on starch properties, and this information may facilitate the development of novel oxidized starches for both food and non-food applications. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Starch bioengineering affects cereal grain germination and seedling establishment

    DEFF Research Database (Denmark)

    Shaik, Shahnoor Sultana; Carciofi, Massimiliano; Martens, Helle Juel

    2014-01-01

    Cereal grain germination is central for plant early development, and efficient germination has a major role in crop propagation and malting. Endosperm starch is the prime energy reserve in germination and seedling establishment. In this study, it was hypothesized that optimized starch granule...... structure, and not only the endosperm starch content per se, is important for germination and seedling establishment. For that purpose, wild-type (WT), and specifically engineered degradable hyperphosphorylated (HP) starch and more resistant amylose-only (AO) starch barley lines were used. The transgenics...... showed no severe phenotypes and the WT and HP lines degraded the starch similarly, having 30% residual starch after 12 d of germination. However, the AO line showed significant resistance to degradation, having 57% residual starch. Interestingly, protein and β-glucan (BG) degradation was stimulated...

  9. Effects of processing conditions on hydrolysis of cassava starch ...

    African Journals Online (AJOL)

    amyloglucosidase using 30% initial cassava starch concentration, which produced 152 g/l reducing sugar concentration and DE of 50.9. The total effective operating time was 60 h. Keywords:Cassava starch, hydrolysis, enzyme, dextrose equivalent.

  10. Comparative studies of starch susceptibilities to α-amylase ...

    African Journals Online (AJOL)

    ayoade

    of the four starch samples varied; amylose content of starch from maize varieties was higher than ... plants as an energy store. ... staple foods as potatoes, wheat, maize (corn), rice and ... of its various chemical and physical properties, can be.

  11. High throughput screening of starch structures using carbohydrate microarrays

    DEFF Research Database (Denmark)

    Tanackovic, Vanja; Rydahl, Maja Gro; Pedersen, Henriette Lodberg

    2016-01-01

    In this study we introduce the starch-recognising carbohydrate binding module family 20 (CBM20) from Aspergillus niger for screening biological variations in starch molecular structure using high throughput carbohydrate microarray technology. Defined linear, branched and phosphorylated...

  12. Evaluation of Starch Biodegradable Plastics Derived from Cassava ...

    African Journals Online (AJOL)

    BSN

    bioplastics produced from cassava does not depend on the level of amylose and amylopectin in the starch per se ... cassava starch is a pure, natural biopolymer that is suitable for ... enzymatic action of microorganisms when disposed, is thus ...

  13. composition and physicochemical properties of starch from christ

    African Journals Online (AJOL)

    Thompson O. Izuagie

    and physicochemical properties of the extracted starch were determined using standard methods. ... water, decorticated to remove skin, dried and ground .... Starches of oval shape have been reported by Hoover et al. ... Figure 2 shows values.

  14. Preparation of Edible Corn Starch Phosphate with Highly Reactive ...

    African Journals Online (AJOL)

    1Food & Bioengineering Department, Henan University of Science and Technology, Luoyang, Henan 471003 ... Purpose: To prepare edible corn starch phosphate under optimized experimental conditions. ... In food industry, starch phosphate.

  15. Effects of Chewing Different Flavored Gums on Salivary Flow Rate and pH

    Directory of Open Access Journals (Sweden)

    Maryam Karami Nogourani

    2012-01-01

    Full Text Available Chewing gum increases salivary flow rate (SFR and pH, but differences in preferences of gum flavor may influence SFR and pH. The aim of this paper was to assess the effect of five different flavors of sucrose-free chewing gum on the salivary flow rate and pH in healthy dental students in Isfahan, Iran. Fifteen (7 men and 8 women healthy dental student volunteers collected unstimulated saliva and then chewed one of five flavored gums for 6 min. The whole saliva was collected and assessed for 6 consecutive days. After unstimulated saliva was collected, stimulated saliva was collected at interval of 0-1, 1–3, and 3–6 minutes after the start of different flavored chewing gums. The SFR and salivary pH were measured. The SFR increased in all five flavored gums at 1, 3, and 6 minutes after start of chewing gums (<0.001. The flow rate of all products reached peak in the 1st minute of stimulation, except spearmint-flavored gums which reached peak in the 6th minute. In the 1st minute, the strawberry-flavored gums showed the highest SFR. During 1–3 minutes, strawberry- and apple-flavored gums showed higher SFR, respectively. Only the spearmint- and cinnamon-flavored gum significantly increased salivary pH. Gum flavored can affect the SFR and pH and special flavors can be advised for different individuals according to their oral conditions.

  16. Chewing gum, occupational stress, work performance and wellbeing. An intervention study.

    Science.gov (United States)

    Smith, Andrew P; Chaplin, Katherine; Wadsworth, Emma

    2012-06-01

    An intervention study was carried out to examine the effects of chewing gum on occupational stress and related outcomes. 101 volunteers from Cardiff University completed the study. The results showed that chewing gum reduced stress (both at work and outside work), reduced fatigue, reduced anxiety and depression and led to a more positive mood. Chewing gum was also associated with perceptions of better performance (both at work and outside). Copyright © 2012 Elsevier Ltd. All rights reserved.

  17. Structural, Thermal, Physical, Mechanical, and Barrier Properties of Chitosan Films with the Addition of Xanthan Gum.

    Science.gov (United States)

    de Morais Lima, Maria; Carneiro, Lucia Cesar; Bianchini, Daniela; Dias, Alvaro Renato Guerra; Zavareze, Elessandra da Rosa; Prentice, Carlos; Moreira, Angelita da Silveira

    2017-03-01

    Films based on chitosan and xanthan gum were prepared using casting technique aiming to investigate the potential of these polymers as packaging materials. Six formulations of films were studied varying the proportion of chitosan and xanthan gum: 100:0 (chitosan:xanthan gum, w/w, C100XG0 film); 90:10 (chitosan:xanthan gum, w/w, C90XG10 film); 80:20 (chitosan:xanthan gum, w/w, C80XG20 film); 70:30 (chitosan:xanthan gum, w/w, C70XG30 film); 60:40 (chitosan:xanthan gum, w/w, C60XG40 film); and 50:50 (chitosan:xanthan gum, w/w, C50XG50 film). The total quantity of solids (chitosan and xanthan gum) in the filmogenic solution was 1.5 g per 100 mL of aqueous solution for all treatments, according to the proportion of each polymer. The films were evaluated by their functional groups, structural, thermal, morphological, physical, mechanical, and barrier properties. All films have presented endothermic peaks in the range of 122 to 175 °C and broad exothermic peaks above 200 °C, which were assigned to the melting temperature and thermal decomposition, respectively. These results demonstrated that films with xanthan gum have the highest T m and Δ m H. The films containing higher content of xanthan gum show also the highest tensile strength and the lowest elongation. Xanthan gum addition did not affect the water vapor permeability, solubility, and moisture of films. This set of data suggests the formation of chitosan-xanthan complexes in the films. © 2017 Institute of Food Technologists®.

  18. Gum cordia as carrier of antioxidants: effects on lipid oxidation of peanuts

    OpenAIRE

    Haq, Muhammad Abdul; Azam, Mahmood; Hasnain, Abid

    2013-01-01

    Performance of antioxidants is improved by incorporating them into polymer matrix such as polysaccharides based edible coatings. Gum cordia, an anionic polysaccharide extracted from the fruits of Cordia.myxa could be used as carrier of antioxidants by virtue of its strong adhering and emulsifying properties. This study aimed to explore the potential of gum cordia as carrier of antioxidants when applied as edible coating on peanuts. Gum Cordia was compared with carboxymethyl cellulose (CMC) in...

  19. Chewing Gum: Cognitive Performance, Mood, Well-Being, and Associated Physiology

    OpenAIRE

    Allen, Andrew P.; Smith, Andrew P.

    2015-01-01

    Recent evidence has indicated that chewing gum can enhance attention, as well as promoting well-being and work performance. Four studies (two experiments and two intervention studies) examined the robustness of and mechanisms for these effects. Study 1 investigated the acute effect of gum on mood in the absence of task performance. Study 2 examined the effect of rate and force of chewing on mood and attention performance. Study 3 assessed the effects of chewing gum during one working day on w...

  20. Chewing gum benefits sustained attention in the absence of task degradation.

    OpenAIRE

    Johnson, A.J.; Muneem, M.; Miles, C.

    2013-01-01

    OBJECTIVES: The present study examined the effect of chewing gum on sustained attention and associated changes in subjective alertness. METHODS: In a within-participants design, 20 participants completed an extended version of the sustained attention response task (SART: Robertson et al., 1997), both with and without chewing gum. Self-rated measures of alertness, contentedness, and calmness were taken before and after the SART. RESULTS: Chewing gum was associated with improved attentional tas...

  1. Electron beam irradiation effects on xanthan gum. Rheological aspects

    International Nuclear Information System (INIS)

    Vieira, F.F.; Del Mastro, N.L.

    2001-01-01

    The paper describes the application of electron beam irradiation to xanthum gum as used as ingredient by the food or cosmetics industry in order to establish their radiosensitivity. The edible powder of xanthum gum samples were irradiated in 1mm thick layers of Petri dishes covered by a transparent PVC of films using an EB accelerator Dynamitron (Radiation Dynamics Inc.) model JOB 188, dose rate 11.17 kGy/s, 0.637 MeV, 1.78 mA, 5 kGy per passage, 3.36 m min -1 with doses of 5, 10, 20 and 50kGy. One % aqueous solutions from irradiated and non-irradiated xanthum gum were prepared and the radiation effects were measured following viscosity changes at 25 deg. C using a Brookfield viscometer; model DVIII, spindel L, with Rheocalc software. Viscosity measurements were performed according to our previous experience and the results are the mean of at least 3 experiments

  2. Comparison of starch granule development and physicochemical properties of starches in wheat pericarp and endosperm.

    Science.gov (United States)

    Yu, Xurun; Zhou, Liang; Zhang, Jing; Yu, Heng; Xiong, Fei; Wang, Zhong

    2015-01-01

    The objectives of this study were: (i) to characterize structural development of starch granule in pericarp and endosperm during wheat caryopsis growth; (ii) to compare physicochemical properties of starches in pericarp and endosperm; (iii) to further discover the relationships between pericarp starches and endosperm starches. Wheat pericarp and endosperm at different development stages were observed by light microscopy and scanning electron microscopy, respectively. Structural properties of starches were determined using X-ray power diffraction and (13) C solid nuclear magnetic resonance. Pericarp starch granules (PSG) accumulated in amyloplasts and chloroplasts, and showed a typical accumulation peak at 5 days after fertilization (DAF), and then gradually decomposed during 5-22 DAF. PSG in the abdominal region showed a higher rate of decomposition compared to the dorsal region of pericarp. Endosperm starch granules (ESG) accumulated in amyloplasts, and occurred in endosperm cells at 5 DAF, then rapidly enriched the endosperm cells until 22 DAF. Compared with ESG, PSG were compound granules of irregular shape and small size distribution. The results also suggested lower amylose content and V-type single-helix content and higher proportions of double helices for PSG compared to ESG. Based on the structural development of PSG and ESG, we speculated that the saccharides resulting from decomposition of PSG, on one hand, enabled the pericarp to survive before maturity of wheat caryopsis and, on the other hand, provided extra nutrition for the growth of ESG. © 2014 Society of Chemical Industry.

  3. Starch behaviors and mechanical properties of starch blend films with different plasticizers.

    Science.gov (United States)

    Nguyen Vu, Hoang Phuong; Lumdubwong, Namfone

    2016-12-10

    The main objective of the study was to gain insight into structural and mechanical starch behaviors of the plasticized starch blend films. Mechanical properties and starch behaviors of cassava (CS)/and mungbean (MB) (50/50, w/w) starch blend films containing glycerol (Gly) or sorbitol (Sor) at 33% weight content were investigated. It was found that tensile strength TS and %E of the Gly-CSMB films were similar to those of MB films; but%E of all Sor-films was identical. TS of plasticized films increased when AM content and crystallinity increased. When Sor was substituted for Gly, crystallinity of starch films and their TS increased. The CSMB and MB films had somewhat a similar molecular profile and comparable mechanical properties. Therefore, it was proposed the starch molecular profile containing amylopectin with high M¯w, low M¯w of amylose, and the small size of intermediates may impart the high TS and%E of starch films. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Locust bean gum: processing, properties and food applications--a review.

    Science.gov (United States)

    Barak, Sheweta; Mudgil, Deepak

    2014-05-01

    Locust bean gum or carob gum is a galactomannan obtained from seed endosperm of carob tree i.e. Ceratonia siliqua. It is widely utilized as an additive in various industries such as food, pharmaceuticals, paper, textile, oil well drilling and cosmetics. Industrial applications of locust bean gum are due to its ability to form hydrogen bonding with water molecule. It is also beneficial in the control of many health problems like diabetes, bowel movements, heart disease and colon cancer due to its dietary fiber action. This article focuses on production, processing, composition, properties, food applications and health benefits of locust bean gum. Copyright © 2014 Elsevier B.V. All rights reserved.

  5. Fabrication of electrospun almond gum/PVA nanofibers as a thermostable delivery system for vanillin.

    Science.gov (United States)

    Rezaei, Atefe; Tavanai, Hossein; Nasirpour, Ali

    2016-10-01

    In this study, the fabrication of vanillin incorporated almond gum/polyvinyl alcohol (PVA) nanofibers through electrospinning has been investigated. Electrospinning of only almond gum was proved impossible. It was found that the aqueous solution of almond gum/PVA (80:20, concentration=7% (w/w)) containing 3% (w/w) vanillin could have successfully electrospun to uniform nanofibers with diameters as low as 77nm. According to the thermal analysis, incorporated vanillin in almond gum/PVA nanofibers showed higher thermal stability than free vanillin, making this composite especially suitable for high temperature applications. XRD and FTIR analyses proved the presence of vanillin in the almond gum/PVA nanofibers. It was also found that vanillin was dispersed as big crystallites in the matrix of almond gum/PVA nanofibers. FTIR analysis showed almond gum and PVA had chemical cross-linking by etheric bonds between COH groups of almond gum and OH groups of PVA. Also, in the nanofibers, there were no major interaction between vanillin and either almond gum or PVA. Copyright © 2016 Elsevier B.V. All rights reserved.

  6. Effect of Teucrium Polium-Containing Chewing Gum on Reducing Salivary Streptococcus Mutans Counts

    Directory of Open Access Journals (Sweden)

    Somayeh Khoramian Tusi

    2018-06-01

    Full Text Available Introduction: Several studies have reported the antibacterial effect of Teucrium polium extract. In this study, we sought to determine the effect of a chewing gum containing the aqueous extract of Teucrium polium on the level of salivary Streptococcus mutans. Materials and Methods: In this double-blind clinical trial, 20 dental students were randomly assigned to two groups of intervention and control. The intervention group received a chewing gum containing the aqueous extract of Teucrium polium, and the control group received a chewing gum without any plant extract. Each person chewed the gum for 20 minutes three times a day (after each meal for three weeks. Unstimulated saliva samples were collected at the beginning of the experiment before the use of the gums and one day after the final gum consumption. The quantitative polymerase chain reaction (qPCR technique was employed to determine the bacterial level. The colonization rate of Streptococcus mutans was compared between the two groups by using t-test in SPSS, version 21. Results: There was no significant difference between the two groups in terms of Streptococcus mutans counts before the intervention (P>0.05. The consumption of Teucrium polium extract-containing chewing gum in comparison with the placebo gum significantly diminished the number of Streptococcus mutans colonies (P=0.002. Conclusion: The results of this study showed that the chewing gum containing the aqueous extract of Teucrium polium significantly lowered the colonization rate of Streptococcus mutans in human saliva.

  7. Whole and crushed nutlets of chia (Salvia hispanica from Mexico as a source of functional gums

    Directory of Open Access Journals (Sweden)

    Maira Segura-Campos

    2014-12-01

    Full Text Available The objective of this study was to characterize the chemical and functional properties of Mexican chia (Salvia hispanica gums extracted from defatted whole and crushed nutlets using the Soxhlet and SFE-CO2 methods. Chia gums have interesting chemical and functional properties for the food industry. The oil and gum yields were in the range of 1.98-16.42% and 5.81-12.60%, respectively. The defatting procedure did not affect significantly the oil and gum extraction; the nutlet type (whole or crushed was the only parameter influencing the yield. The proximate composition and the protein and fiber contents of chia gum were evaluated. Low contents of protein and fiber and high NFE levels were found in whole nutlet gums. The functional properties of chia gum extracted from whole and crushed nutlets with the Soxhlet and SFE-COs methods showed the following ranges of water absorption capacity of 62.64 to 143.66 g/g, water adsorption capacity of 0.69 to 1.35 g/g, and water and oil holding capacity of 100 to 149.28 g/g and19.5 to 40.4 g/g, respectively. The rheological behavior exhibited by the gums was pseudoplastic or shear thinning. From a functional perspective, chia gum is an important food component due its emulsifier and stabilizer potentials.

  8. Rapid screening of guar gum using portable Raman spectral identification methods.

    Science.gov (United States)

    Srivastava, Hirsch K; Wolfgang, Steven; Rodriguez, Jason D

    2016-01-25

    Guar gum is a well-known inactive ingredient (excipient) used in a variety of oral pharmaceutical dosage forms as a thickener and stabilizer of suspensions and as a binder of powders. It is also widely used as a food ingredient in which case alternatives with similar properties, including chemically similar gums, are readily available. Recent supply shortages and price fluctuations have caused guar gum to come under increasing scrutiny for possible adulteration by substitution of cheaper alternatives. One way that the U.S. FDA is attempting to screen pharmaceutical ingredients at risk for adulteration or substitution is through field-deployable spectroscopic screening. Here we report a comprehensive approach to evaluate two field-deployable Raman methods--spectral correlation and principal component analysis--to differentiate guar gum from other gums. We report a comparison of the sensitivity of the spectroscopic screening methods with current compendial identification tests. The ability of the spectroscopic methods to perform unambiguous identification of guar gum compared to other gums makes them an enhanced surveillance alternative to the current compendial identification tests, which are largely subjective in nature. Our findings indicate that Raman spectral identification methods perform better than compendial identification methods and are able to distinguish guar gum from other gums with 100% accuracy for samples tested by spectral correlation and principal component analysis. Published by Elsevier B.V.

  9. Effects of chewing gum and time-on-task on alertness and attention.

    Science.gov (United States)

    Allen, A P; Smith, A P

    2012-07-01

    Chewing gum has been shown to reliably increase subjective alertness whereas the effects on attention are more variable. It has been suggested that chewing gum only enhances attention when the person has been performing a task for some time. The current research aimed to investigate if time-on-task trends enhancing effects of chewing gum could be observed in alertness and attention during and following chewing. Study 1 used tests of reported mood, including reported mood, and tests of attention (categoric search, focussed attention, simple reaction time, and vigilance). These tasks were performed shortly after the start of chewing. Study 2 examined effects of previous and current chewing on reported alertness and the attention tests. Study 1 showed that chewing gum increased reported alertness and hedonic tone and improved performance on the categoric search task. Chewing gum maintained reported alertness across sessions in study 2. In the first experimental session of study 2 gum improved categoric search performance, and during the second session gum broadened focus of attention and quickened vigilance reaction time. This effect on vigilance reaction time was moderated by time-on-task, with an initial negative effect being replaced by a positive effect. The results confirm the robust effect of chewing gum on reported alertness and show that changes in the effects of chewing gum on attention require further investigation. Future research may also determine underlying mechanisms for an alerting effect.

  10. Starch and starch hydrolysates are favorable carbon sources for bifidobacteria in the human gut.

    Science.gov (United States)

    Liu, Songling; Ren, Fazheng; Zhao, Liang; Jiang, Lu; Hao, Yanling; Jin, Junhua; Zhang, Ming; Guo, Huiyuan; Lei, Xingen; Sun, Erna; Liu, Hongna

    2015-03-01

    Bifidobacteria are key commensals in human gut, and their abundance is associated with the health of their hosts. Although they are dominant in infant gut, their number becomes lower in adult gut. The changes of the diet are considered to be main reason for this difference. Large amounts of whole-genomic sequence data of bifidobacteria make it possible to elucidate the genetic interpretation of their adaptation to the nutrient environment. Among the nutrients in human gut, starch is a highly fermentable substrate and can exert beneficial effects by increasing bifidobacteria and/or being fermented to short chain fatty acids. In order to determine the potential substrate preference of bifidobacteria, we compared the glycoside hydrolase (GH) profiles of a pooled-bifidobacterial genome (PBG) with a representative microbiome (RM) of the human gut. In bifidobacterial genomes, only 15% of GHs contained signal peptides, suggesting their weakness in utilization of complex carbohydrate, such as plant cell wall polysaccharides. However, compared with other intestinal bacteria, bifidobacteiral genomes encoded more GH genes for degrading starch and starch hydrolysates, indicating that they have genetic advantages in utilizing these substrates. Bifidobacterium longum subsp. longum BBMN68 isolated from centenarian's faeces was used as a model strain to further investigate the carbohydrate utilization. The pathway for degrading starch and starch hydrolysates was the only complete pathway for complex carbohydrates in human gut. It is noteworthy that all of the GH genes for degrading starch and starch hydrolysates in the BBMN68 genome were conserved in all studied bifidobacterial strains. The in silico analyses of BBMN68 were further confirmed by growth experiments, proteomic and real-time quantitative PCR (RT-PCR) analyses. Our results demonstrated that starch and starch hydrolysates were the most universal and favorable carbon sources for bifidobacteria. The low amount of these

  11. Retention of Cationic Starch onto Cellulose Fibres

    Science.gov (United States)

    Missaoui, Mohamed; Mauret, Evelyne; Belgacem, Mohamed Naceur

    2008-08-01

    Three methods of cationic starch titration were used to quantify its retention on cellulose fibres, namely: (i) the complexation of CS with iodine and measurement of the absorbency of the ensuing blue solution by UV-vis spectroscopy; (ii) hydrolysis of the starch macromolecules followed by the conversion of the resulting sugars to furan-based molecules and quantifying the ensuing mixture by measuring their absorbance at a Ι of 490 nm, using the same technique as previous one and; finally (iii) hydrolysis of starch macromolecules by trifluoro-acetic acid and quantification of the sugars in the resulting hydrolysates by high performance liquid chromatography. The three methods were found to give similar results within the range of CS addition from 0 to 50 mg per g of cellulose fibres.

  12. Examination of injection moulded thermoplastic maize starch

    Directory of Open Access Journals (Sweden)

    2007-12-01

    Full Text Available This paper focuses on the effect of the different injection moulding parameters and storing methods on injection moulded thermoplastic maize starch (TPS. The glycerol and water plasticized starch was processed in a twin screw extruder and then with an injection moulding machine to produce TPS dumbbell specimens. Different injection moulding set-ups and storing conditions were used to analyse the effects on the properties of thermoplastic starch. Investigated parameters were injection moulding pressure, holding pressure, and for the storage: storage at 50% relative humidity, and under ambient conditions. After processing the mechanical and shrinkage properties of the manufactured TPS were determined as a function of the ageing time. While conditioning, the characteristics of the TPS changed from a soft material to a rigid material. Although this main behaviour remained, the different injection moulding parameters changed the characteristics of TPS. Scanning electron microscope observations revealed the changes in the material on ageing.

  13. Fragrant starch-based films with limonene

    Directory of Open Access Journals (Sweden)

    Adrian K. Antosik

    2017-02-01

    Full Text Available Novel fragrant starch-based films with limonene were successfully prepared. Biodegradable materials of natural origin were used and the process was relatively simple and inexpensive. The effect of limonene on physicochemical properties of starch-based films (moisture absorption, solubility in water, wettability, mechanical properties were compared to glycerol plasticized system. Taking into consideration that the obtained materials could also exhibit bactericidal and fungicidal properties, the studies with Escherichia coli, Candida albicans and Aspergillus niger were performed. Such a material could potentially find application in food packaging (e.g. masking unpleasant odors, hydrophilic starch film would prevent food drying, or in agriculture (e.g. for seed encapsulated tapes.

  14. Starch deposits in Themeda triandra Forsk | WRE | African Journal of ...

    African Journals Online (AJOL)

    Themeda triandra tillers were examined microscopically at one to two-weekly intervals to determine where starch was deposited. Large numbers of starch grains were always present but the position of these deposits varied according to growth activity and flowering time of the plant. Starch deposits in the roots were usually ...

  15. Mechanical Properties of Potato- Starch Linear Low Density ...

    African Journals Online (AJOL)

    The mechanical properties of potato-starch filled LLDPE such as Young's Modulus, tensile strength and elongation at break were studied. Apart from the Young's Modulus, the tensile strength and elongation at break reduced with increased starch content. This is attributed to poor adhesion between starch and the polymer ...

  16. Composition and Physicochemical Properties of Starch from Christ ...

    African Journals Online (AJOL)

    Starch was extracted from seeds of Christ Thorn by hot water extraction method. The composition and physicochemical properties of the extracted starch were determined using standard methods. The results obtained from the analyses revealed that the % yield of starch was 43.2%, while moisture content, ash content, ...

  17. Coordination of cassava starch to metal ions and thermolysis of ...

    African Journals Online (AJOL)

    Cassava starch formed Werner-type complexes with ions of metals from the transition groups. This was proven by conductivity and electron paramagnetic resonance measurements. The coordination of starch to central metal ions influenced the thermal decomposition of starch. As a rule complexes started to decompose at ...

  18. Evaluation and Optimization of Godare Starch as a Binder and ...

    African Journals Online (AJOL)

    The binding and disintegrating properties of Godare (Colcosia esculenta) starch in paracetamol tablet formulations were evaluated in comparison with potato starch. Tablet crushing strengths (Hs), friabilities Frs), disintegration times (DTs) and porosities were determined. The results showed that Godare starch has a better ...

  19. Mechanochemical degradation of potato starch paste under ultrasonic irradiation

    Institute of Scientific and Technical Information of China (English)

    LI Jian-bin; LI Lin; LI Bing; CHEN Ling; GUI Lin

    2006-01-01

    In the paper, changes in the molecular weight, the intrinsic viscosity and the polydispersity (molecular mass distribution) of treated potato starch paste were studied under different ultrasonic conditions which include irradiation time, ultrasonic intensity, potato starch paste concentration, and distance from probe tip on the degradation of potato starch paste. Intrinsic viscosity of potato starch paste was determined following the ASTM (American Society for Testing and Materials) standard practice for dilute solution viscosity of polymers. Molecular mass and polydispersity of potato starch paste were measured on GPC (Gel Permeation Chromatography). The results showed that the average molecular mass and the intrinsic viscosity of starch strongly depended on irradiation time. Degradation increased with prolonged ultrasonic irradiation time, and the increase of ultrasonic intensity could accelerate the degradation, resulting in a faster degradation rate, a lower limiting value and a higher degradation extent. Starch samples were degraded faster in dilute solutions than in concentrated solutions. The molecular mass and the intrinsic viscosity of starch increased with the increase of distance from probe tip. Our results also showed that the polydispersity decreased with ultrasonic irradiation under all ultrasonic conditions. Ultrasonic degradation of potato starch paste occured based on the mechanism of molecular relaxation of starch paste. In the initial stage, ultrasonic degradation of potato starch paste was a random process, and the molecular mass distribution was broad. After that, ultrasonic degradation of potato starch paste changed to a nonrandom process, and the molecular mass distribution became narrower. Finally, molecular mass distribution tended toward a saturation value.

  20. Engineering potato starch with a higher phosphate content

    NARCIS (Netherlands)

    Xu, Xuan; Huang, Xing Feng; Visser, Richard G.F.; Trindade, Luisa M.

    2017-01-01

    Phosphate esters are responsible for valuable and unique functionalities of starch for industrial applications. Also in the cell phosphate esters play a role in starch metabolism, which so far has not been well characterized in storage starch. Laforin, a human enzyme composed of a

  1. The oxidation of the aldehyde groups in dialdehyde starch

    NARCIS (Netherlands)

    Haaksman, I.K.; Besemer, A.C.; Jetten, J.M.; Timmermans, J.W.; Slaghek, T.M.

    2006-01-01

    This paper describes the difference in relative reactivity of the aldehyde groups present in dialdehyde starch towards different oxidising agents. The oxidation of dialdehyde starch with peracetic acid and sodium bromide leads to only partial oxidation to give mono-aldehyde-carboxy starch, while

  2. Starch-based Foam Composite Materials: processing and bioproducts

    Science.gov (United States)

    Starch is an abundant, biodegradable, renewable and low-cost commodity that has been explored as a replacement for petroleum-based plastics. By itself, starch is a poor replacement for plastics because of its moisture sensitivity and brittle properties. Efforts to improve starch properties and funct...

  3. Isolation and Characterization of Starches from eight Dioscorea ...

    African Journals Online (AJOL)

    AJB SERVER

    2006-09-04

    Sep 4, 2006 ... temperature, with Moonshine (895.551 ± 1.051%) having the highest swelling power ... The properties of the different Dioscorea alata starches may prove useful in nutritional applications. ..... coating. Starch/Starke 44: 393-398. Ayensu ES, Coursey DG (1972). ... World production and marketing of starch. In:.

  4. Kinetics of starch digestion and performance of broiler chickens

    NARCIS (Netherlands)

    Weurding, R.E.

    2002-01-01

    Keywords: starch, digestion rate, broiler chickens, peas, tapioca

    Starch is stored in amyloplasts of various plants like cereals and legumes and seeds of these plants are used as feedstuffs for farm animals. Starch is the major energy

  5. Production of amorphous starch powders by solution spray drying

    NARCIS (Netherlands)

    Niazi, Muhammad B. K.; Broekhuis, Antonius A.

    2012-01-01

    The spray drying of starch/maltodextrin formulations was evaluated as a potential technology for the manufacturing of amorphous thermoplastic starches. Mixtures of starches with high to low amylose (Am)amylopectin (Ap) ratios were spray-dried from water-based solutions and granular dispersions. The

  6. Evaluation of the effect of ginger modified cassava starch as ...

    African Journals Online (AJOL)

    Raw cassava starch has been used as thickener and binder in the formulation of water based paint, but with a problem of loss of viscosity in a very short period. This study evaluates the modification of cassava starch using active component of ginger extract and its use as a water- based paint thickener. 150 g of starch in ...

  7. Self-healing guar gum and guar gum-multiwalled carbon nanotubes nanocomposite gels prepared in an ionic liquid.

    Science.gov (United States)

    Sharma, Mukesh; Mondal, Dibyendu; Mukesh, Chandrakant; Prasad, Kamalesh

    2013-10-15

    Guar gum is a galactomannan extracted from the seed of the leguminous shrub Cyamopsis tetragonoloba. It was found to form a soft viscoelastic gel in 1-butyl-3-methylimidazolium chloride, an ionic liquid at an optimized concentration of 10%w/v. A nanocomposite gel of the gum with enhanced strength could be prepared with 0.2%w/v of multiwalled carbon nanotubes (MWCNTs) in the ionic liquid. When the gels thus prepared were subjected to surface fractures or bisected completely, they found to self-heal at room temperature without any external interventions. The self-healing process could be repeated several times. These viscoelastic gel systems showed thixotropic nature and recovery of the storage modulus with time for several cycles was observed upon rheological investigations. The interaction took place between ionic liquid, guar gum and MWCNT was studied by SEM, TEM, FT-IR, powder XRD and rheometry. The results suggested that, upon standing at room temperature development of electrostatic interactions and the van der Waals interactions among the ionic liquid molecules facilitated the formation of reversible noncovalent bonds and eventually activated the self-healing in the gel systems through appropriate chain entanglements. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Study on plant Gums and their new development in application: with focus on tragacanth, guar and arabic Gum; a short review

    Directory of Open Access Journals (Sweden)

    F. Hassanpour

    2016-01-01

    Full Text Available Gums refer to a type of polysaccharides which are used to increase viscosity and create some other functional properties such as thickening agent, emulsifying agent, stabilizer, crystal inhibitor and so forth. They are classifying based on their nature and originality including, microbial, plant, exudate and animal Gums. This article shortly reviews a group of plant Gums and recent findings in their application. Gums or Hydrocolloids are main compounds which create stability of emulsion via entering into water phase. The importance of these compounds is on viscosity and electrostatic reactions to stabilize nonalcoholic emulsion with below properties; 1 easily soluble in cold water, 2 the lowest amount of viscosity in water, 3 having maximum level of emulsifier amount, 4 no creation of gelling. Diversity and functionality of Gums and regarding their still novelty in food industries have made Gums one of the main additives in food formulations. Since sourced of Gums are different we must focus on using them together to improve their synergistic effect but interactions among them and combined matrixes produced by them also need to be studied in details.

  9. Control of starch content in potato

    International Nuclear Information System (INIS)

    Korshunov, A.V.; Filippova, G.I.; Gaitova, N.A.; Kutovenko, L.N.

    2010-01-01

    The physiological and biochemical changes and connections defining the starch accumulation in potato tubers are showed. Using the radioisotope C14O2 are analysed data on carbohydrates accumulation in leaves, speed of their movement in tubers, synthetic and decomposing enzyme activities in plant organs, the content of starch in tubers depending on the combination of fertilizers. The necessity for dose phosphorus application level not lower than nitrogen is reasoned. Recommendations on the optimal combination of macrofertilizers, ensuring compromise between yield and tuber starchiness for sod-podzoil sandy-loam and loamy, grey forest, peat, chernozem soils in dry-farming and irrigation are given [ru

  10. Modification of potato starch granule structure and morphology in planta by expression of starch binding domain fusion proteins

    NARCIS (Netherlands)

    Huang, X.

    2010-01-01

    Producing starches with altered composition, structure and novel physico-chemical properties in planta by manipulating the enzymes which are involved in starch metabolism or (over)expressing heterologous enzymes has huge advantages such as broadening the range of starch applications and reducing the

  11. The release of vitamin C from chewing gum and its effects on supragingival calculus formation.

    Science.gov (United States)

    Lingström, Peter; Fure, Solveig; Dinitzen, Bettina; Fritzne, Christina; Klefbom, Carin; Birkhed, Dowen

    2005-02-01

    The aims of this study were to evaluate (i): whether vitamin C in chewing gum, alone or in combination with carbamide, influences calculus formation, and (ii) whether carbamide affects the release, stability and uptake of vitamin C in a chewing gum. In two test series (Series I and II), 30 subjects, all calculus formers, participated. They were instructed to chew on five (Series I) or 10 (Series II) pieces of gum per day for a period of 3 months. The chewing gums were: vitamin C (60 mg, Series I), non-vitamin C (Series I) and vitamin C + carbamide (30 mg + 30 mg, Series II). In both series, no gum was used as a negative control. Calculus formation was scored on three lingual sites on the six anterior mandibular teeth according to the Volpe-Manhold index. The effect on plaque and gingivitis was also determined. A significant reduction in the total calculus score was observed after the use of vitamin C (33%) and vitamin C + carbamide (12%) gums compared with no gum use; this reduction was most pronounced in the heavy calculus formers. A reduced amount of visible plaque was also observed after use of vitamin C and non-vitamin C gum, but only the vitamin C gum reduced the number of bleeding sites (37%). In a separate study, the release, stability and uptake of vitamin C were evaluated using the iodine titration method in both saliva and urine after exposure to the following gums: vitamin C + carbamide (30 mg + 30 mg) and vitamin C (30 mg). There was no indication that carbamide affected the release, stability or uptake of vitamin C when used in a chewing gum.

  12. Inducing PLA/starch compatibility through butyl-etherification of waxy and high amylose starch

    CSIR Research Space (South Africa)

    Wokadala, OC

    2014-06-01

    Full Text Available In this study, waxy and high amylose starches were modified through butyl-etherification to facilitatecompatibility with polylactide (PLA). Fourier transform infrared spectroscopy, proton nuclear magneticresonance spectroscopy and wettability tests...

  13. Mechanical Properties of Isotactic Polypropylene Modified with Thermoplastic Potato Starch

    Science.gov (United States)

    Knitter, M.; Dobrzyńska-Mizera, M.

    2015-05-01

    In this paper selected mechanical properties of isotactic polypropylene (iPP) modified with potato starch have been presented. Thermoplastic starch (TPS) used as a modifier in the study was produced from potato starch modified with glycerol. Isotactic polypropylene/thermoplastic potato starch composites (iPP/TPS) that contained 10, 30, 50 wt.% of modified starch were examined using dynamic mechanical-thermal analysis, static tensile, Brinell hardness, and Charpy impact test. The studies indicated a distinct influence of a filler content on the mechanical properties of composites in comparison with non-modified polypropylene.

  14. The effect of starch amylose content on the morphology andproperties of melt-processed butyl-etherified starch/poly[(butylenesuccinate)-co-adipate] blends

    CSIR Research Space (South Africa)

    Maubane, Lesego T

    2017-01-01

    Full Text Available structures. Thermogravimetric analysis revealed that the thermal stability of the blends decreased with increasing starch loading for all starch types with varying amylose content; however, the nature of the starch controlled the mechanical properties...

  15. Wheat B-starch based polymeric materials

    Czech Academy of Sciences Publication Activity Database

    Kotek, Jiří; Kruliš, Zdeněk; Šárka, E.

    2011-01-01

    Roč. 105, č. 9 (2011), s. 731 ISSN 0009-2770. [International Conference on Polysaccharides-Glycoscience /7./. 02.11.2011-04.11.2011, Prague] R&D Projects: GA ČR GA525/09/0607 Institutional research plan: CEZ:AV0Z40500505 Keywords : biodegradable plastic * polycaprolactone * B- starch Subject RIV: JI - Composite Materials

  16. Starch: chemistry, microstructure, processing and enzymatic degradation

    Science.gov (United States)

    Starch is recognized as one of the most abundant and important commodities containing value added attributes for a vast number of industrial applications. Its chemistry, structure, property and susceptibility to various chemical, physical and enzymatic modifications offer a high technological value ...

  17. Starch facilitates enzymatic wheat gluten hydrolysis

    NARCIS (Netherlands)

    Hardt, N.A.; Boom, R.M.; Goot, van der A.J.

    2015-01-01

    Wheat gluten can be hydrolyzed by either using (vital) wheat gluten or directly from wheat flour. This study investigates the influence of the presence of starch, the main component of wheat, on enzymatic wheat gluten hydrolysis. Wheat gluten present in wheat flour (WFG) and vital wheat gluten (VWG)

  18. Some rheological properties of sodium caseinate-starch gels.

    Science.gov (United States)

    Bertolini, Andrea C; Creamer, Lawrence K; Eppink, Mieke; Boland, Mike

    2005-03-23

    The influence of sodium caseinate on the thermal and rheological properties of starch gels at different concentrations and from different botanical sources was evaluated. In sodium caseinate-starch gels, for all starches with the exception of potato starch, the sodium caseinate promoted an increase in the storage modulus and in the viscosity of the composite gel when compared with starch gels. The addition of sodium caseinate resulted in an increase in the onset temperature, the gelatinization temperature, and the end temperature, and there was a significant interaction between starch and sodium caseinate for the onset temperature, the peak temperature, and the end temperature. Microscopy results suggested that sodium caseinate promoted an increase in the homogeneity in the matrix of cereal starch gels.

  19. Barley starch bioengineering for high phosphate and amylose

    DEFF Research Database (Denmark)

    Blennow, Per Gunnar Andreas; Carciofi, Massimiliano; Shaik, Shahnoor Sultana

    2011-01-01

    Starch is a biological polymer that can be industrially produced in massive amounts in a very pure form. Cereals is the main source for starch production and any improvement of the starch fraction can have a tremendous impact in food and feed applications. Barley ranks number four among cereal...... crops and barley is a genetically very well characterized. Aiming at producing new starch qualities in the cereal system, we used RNAi and overexpression strategies to produce pure amylose and high-phosphate starch, respectively, using the barley kernel as a polymer factory. By simultaneous silencing...... of the three genes encoding the starch-branching enzymes SBEI, SBEIIa, and SBEIIb using a triple RNAi chimeric hairpin construct we generated a virtually amylopectin-free barley. The grains of the transgenic lines were shrunken and had a yield of around 80% of the control line. The starch granules were...

  20. Biodegradability and mechanical properties of starch films from Andean crops.

    Science.gov (United States)

    Torres, F G; Troncoso, O P; Torres, C; Díaz, D A; Amaya, E

    2011-05-01

    Different Andean crops were used to obtain starches not previously reported in literature as raw material for the production of biodegradable polymers. The twelve starches obtained were used to prepare biodegradable films by casting. Water and glycerol were used as plasticizers. The mechanical properties of the starch based films were assessed by means of tensile tests. Compost tests and FTIR tests were carried out to assess biodegradability of films. The results show that the mechanical properties (UTS, Young's modulus and elongation at break) of starch based films strongly depend on the starch source used for their production. We found that all the starch films prepared biodegrade following a three stage process and that the weight loss rate of all the starch based films tested was higher than the weight loss rate of the cellulose film used as control. Copyright © 2011 Elsevier B.V. All rights reserved.

  1. Influence of different hydrocolloids on dough thermo-mechanical properties and in vitro starch digestibility of gluten-free steamed bread based on potato flour.

    Science.gov (United States)

    Liu, Xingli; Mu, Taihua; Sun, Hongnan; Zhang, Miao; Chen, Jingwang; Fauconnier, Marie Laure

    2018-01-15

    The effects of hydrocolloids (hydroxypropylmethylcellulose (HPMC), Carboxymethylcellulose (CMC), xanthan gum (XG), and apple pectin (AP)) at different concentrations on dough thermo-mechanical properties and in vitro starch digestibility of gluten-free potato steamed bread were investigated. Results showed that hydrocolloids addition significantly increased the gelatinization temperature (from 52.0 to 64.2°C) and water absorption (from 56.22 to 66.50%) of potato dough. Moreover, hydrocolloids may be interacted with protein and starch, the density of potato protein bands was decreased by hydrocolloids addition, the reason might be that higher molecular weight complexes might be formed between proteins-hydrocolloids or proteins-proteins, thus change the protein solubility. Furthermore, steamed breads with hydrocolloids presented higher specific volume and lower hardness, and the rapidly digestible starch and estimated glycemic index were significantly decreased from 45.51 to 20.64, from 69.54 to 55.17, respectively. In conclusion, HPMC and XG could be used as improvers in the gluten-free potato steamed bread. Copyright © 2017. Published by Elsevier Ltd.

  2. PROTEIN TARGETING TO STARCH is required for localising GRANULE-BOUND STARCH SYNTHASE to starch granules and for normal amylose synthesis in Arabidopsis.

    Directory of Open Access Journals (Sweden)

    David Seung

    2015-02-01

    Full Text Available The domestication of starch crops underpinned the development of human civilisation, yet we still do not fully understand how plants make starch. Starch is composed of glucose polymers that are branched (amylopectin or linear (amylose. The amount of amylose strongly influences the physico-chemical behaviour of starchy foods during cooking and of starch mixtures in non-food manufacturing processes. The GRANULE-BOUND STARCH SYNTHASE (GBSS is the glucosyltransferase specifically responsible for elongating amylose polymers and was the only protein known to be required for its biosynthesis. Here, we demonstrate that PROTEIN TARGETING TO STARCH (PTST is also specifically required for amylose synthesis in Arabidopsis. PTST is a plastidial protein possessing an N-terminal coiled coil domain and a C-terminal carbohydrate binding module (CBM. We discovered that Arabidopsis ptst mutants synthesise amylose-free starch and are phenotypically similar to mutants lacking GBSS. Analysis of granule-bound proteins showed a dramatic reduction of GBSS protein in ptst mutant starch granules. Pull-down assays with recombinant proteins in vitro, as well as immunoprecipitation assays in planta, revealed that GBSS physically interacts with PTST via a coiled coil. Furthermore, we show that the CBM domain of PTST, which mediates its interaction with starch granules, is also required for correct GBSS localisation. Fluorescently tagged Arabidopsis GBSS, expressed either in tobacco or Arabidopsis leaves, required the presence of Arabidopsis PTST to localise to starch granules. Mutation of the CBM of PTST caused GBSS to remain in the plastid stroma. PTST fulfils a previously unknown function in targeting GBSS to starch. This sheds new light on the importance of targeting biosynthetic enzymes to sub-cellular sites where their action is required. Importantly, PTST represents a promising new gene target for the biotechnological modification of starch composition, as it is

  3. Modification of rice starch by gamma irradiation to produce soluble starch of low viscosity for industrial purposes

    International Nuclear Information System (INIS)

    El Saadany, R.M.A.; El Saadany, F.M.; Foda, Y.H.

    1974-01-01

    Because starch of low viscosity is important for industrial purposes this research was carried out to study the possibility of producing this sort of starch by treating rice starch with γ-irradiation. Results indicated than when rice starch was modified by γ-irradiation, the reducing power increased and degradation as well as molecular breakdown occured followed by sharp decrease of its viscosity, specific viscosity and intrisinc viscosity. Results showed that starch became more soluble by treating with γ-irradiation and lost its resistance to water as its swelling capacity decreased. All these changes were proportional to the doses of γ-irradiation. (orig.) [de

  4. In situ effect of CPP-ACP chewing gum upon erosive enamel loss

    Directory of Open Access Journals (Sweden)

    Catarina Ribeiro Barros de ALENCAR

    Full Text Available Abstract Casein phosphopeptide-amorphous calcium phosphate (CPP-ACP is able to increase salivary calcium and phosphate levels at an acidic pH. Previous studies demonstrated that a CPP-ACP chewing gum was able to enhance the re-hardening of erosion lesions, but could not diminish enamel hardness loss. Therefore, there is no consensus regarding the effectiveness of CPP-ACP on dental erosion. Objective This in situ study investigated the ability of a CPP-ACP chewing gum in preventing erosive enamel loss. Material and Methods: During three experimental crossover phases (one phase per group of seven days each, eight volunteers wore palatal devices with human enamel blocks. The groups were: GI – Sugar free chewing gum with CPP-ACP; GII – Conventional sugar free chewing gum; and GIII – No chewing gum (control. Erosive challenge was extraorally performed by immersion of the enamel blocks in cola drink (5 min, 4x/day. After each challenge, in groups CPP and No CPP, volunteers chewed one unit of the corresponding chewing gum for 30 minutes. Quantitative analysis of enamel loss was performed by profilometry (µm. Data were analyzed by Repeated-Measures ANOVA and Tukey’s test (p0.05. Conclusion The CPP-ACP chewing gum was not able to enhance the anti-erosive effect of conventional chewing gum against enamel loss.

  5. Effects of Chewing Different Flavored Gums on Salivary Flow Rate and pH.

    Science.gov (United States)

    Karami Nogourani, Maryam; Janghorbani, Mohsen; Kowsari Isfahan, Raha; Hosseini Beheshti, Mozhgan

    2012-01-01

    Chewing gum increases salivary flow rate (SFR) and pH, but differences in preferences of gum flavor may influence SFR and pH. The aim of this paper was to assess the effect of five different flavors of sucrose-free chewing gum on the salivary flow rate and pH in healthy dental students in Isfahan, Iran. Fifteen (7 men and 8 women) healthy dental student volunteers collected unstimulated saliva and then chewed one of five flavored gums for 6 min. The whole saliva was collected and assessed for 6 consecutive days. After unstimulated saliva was collected, stimulated saliva was collected at interval of 0-1, 1-3, and 3-6 minutes after the start of different flavored chewing gums. The SFR and salivary pH were measured. The SFR increased in all five flavored gums at 1, 3, and 6 minutes after start of chewing gums (P salivary pH. Gum flavored can affect the SFR and pH and special flavors can be advised for different individuals according to their oral conditions.

  6. Protein-free cress seed (Lepidium sativum) gum: Physicochemical characterization and rheological properties

    DEFF Research Database (Denmark)

    Razmkhah, Somayeh; Razavi, Seyed Mohammad Ali; Mohammadifar, Mohammad Amin

    2016-01-01

    Protein-free cress seed gum (PFCSG) was obtained by precipitation of crude cress seed gum (CSG) withethanol followed by treatment with protease. Molecular weight, moisture, ash and uronic acids contentdecreased after elimination of protein. Elimination of protein improved significantly rheologica...

  7. intra-species variation of the properties of gum exudates from Acacia

    African Journals Online (AJOL)

    a

    The results show that significant inter-species variation of the properties of the gum exudates from the two species exist, whereas only some parameters show significant intra-species variation. The specific optical rotations of the gum exudates have been found to vary from ---43.2o to ---52o for Acacia senegal var. senegal ...

  8. Recent advances in Rosaceae gum exudates: From synthesis to food and non-food applications.

    Science.gov (United States)

    Bouaziz, Fatma; Koubaa, Mohamed; Ellouz Ghorbel, Raoudha; Ellouz Chaabouni, Semia

    2016-05-01

    In recent years, great interest has been devoted to the development of new applications for natural gums. These molecules were used for a variety of purposes since they are chemically inert, non-toxic, less expensive, biodegradable and widely available. They represent one of the most abundant raw materials used not only in commercial food products, but also in cosmetic and pharmaceutical products. Plant gums take their advantages compared to other gums (e.g., from animal and microbial sources) mainly because of their acceptance by consumers. Despite of the well description given in literature for the features of plant gum exudates, there is a lack distinguishing the different families that are producing gums, and their potential applications. Among these gums, the ones produced by Rosaceae family (e.g., almond, apricot, cherry, peach, and plum plants) have been taking special attention. Thus, the aim of this review is to report the recent advances in Rosaceae gum exudates. An emphasis is given for the formation mechanisms of these gums, their chemical composition, functional properties and structures, beneficial properties, as well as their food/non-food applications. Copyright © 2016 Elsevier B.V. All rights reserved.

  9. Influence of gamma radiation on the physicochemical and rheological properties of sterculia gum polysaccharides

    International Nuclear Information System (INIS)

    Singh, Baljit; Sharma, Vikrant

    2013-01-01

    Keeping in view the influence of gamma radiation on the physiochemical properties of the polysaccharides and their importance in the food and pharmaceutical industry, in the present study attempt has been made to investigate the effects of absorbed dose on FTIR, XRD, SEMs, absorbance, pH, solubility, water absorption capacity, emulsion stability and rheology of sterculia gum. Increase in solubility and decrease in swellability of gum has been observed on increasing the absorbed dose. The emulsion stability has improved for the gum sample irradiated with total dose of 8.1±0.2 kGy. Apparent viscosity of gum solution first increased with increase in dose from 0 to 8.1±0.2 kGy than decreased with regular trends with further increase in total absorbed dose. Flow behavior of gum solution shifted to Newtonian from non-Newtonian with increasing the dose. - Highlights: • Solubility increased and swellability decreased of gum on increasing the total dose. • Apparent viscosity of gum solution increased upto 8.1 kGy then decreased. • Emulsion stability improved for gum irradiated with total dose of 8.1 kGy. • Flow behavior shifted to Newtonian from non-Newtonian with increasing total dose

  10. Rheological and Quality Characteristics of Taftoon Bread as Affected by Salep and Persian Gums

    Directory of Open Access Journals (Sweden)

    M. A. Sahari

    2014-01-01

    Full Text Available Effects of salep gum at concentrations of 0.5%, 1%, 3%, and 5% (w/w flour basis and the Persian gum at concentrations of 0.5%, 1%, and 3% (w/w flour basis and combination of the two gums at concentrations of 0.5% + 0.5%, 0.75% + 0.25%, and 0.25% + 0.75% on rheological properties of the wheat flour dough and quality of Taftoon bread were studied with regard to retardation of staling. Rheological (farinograph and extensograph characteristics, staling, and organoleptic evaluations were performed on the dough and the resulting Taftoon bread. Statistical results showed that the salep gum at 5% and Persian gum at 3% (w/w flour basis had a significant effect on the dough properties. Salep and Persian gums when each separately added increased and decreased dough water absorption, respectively. Both hydrocolloids increased the dough resistance to extension and decreased its extensibility. Persian gum shows dual nature in water absorption and some other baking properties. Textural studies revealed that addition of 5% salep gum (w/w flour basis reduced the bread crumb firmness and delayed the staling process of the Taftoon bread. X-ray diffraction study also confirmed this result.

  11. Rheological and Quality Characteristics of Taftoon Bread as Affected by Salep and Persian Gums.

    Science.gov (United States)

    Sahari, M A; Mohammadi, R; Hamidi Esfehani, Z

    2014-01-01

    Effects of salep gum at concentrations of 0.5%, 1%, 3%, and 5% (w/w flour basis) and the Persian gum at concentrations of 0.5%, 1%, and 3% (w/w flour basis) and combination of the two gums at concentrations of 0.5% + 0.5%, 0.75% + 0.25%, and 0.25% + 0.75% on rheological properties of the wheat flour dough and quality of Taftoon bread were studied with regard to retardation of staling. Rheological (farinograph and extensograph) characteristics, staling, and organoleptic evaluations were performed on the dough and the resulting Taftoon bread. Statistical results showed that the salep gum at 5% and Persian gum at 3% (w/w flour basis) had a significant effect on the dough properties. Salep and Persian gums when each separately added increased and decreased dough water absorption, respectively. Both hydrocolloids increased the dough resistance to extension and decreased its extensibility. Persian gum shows dual nature in water absorption and some other baking properties. Textural studies revealed that addition of 5% salep gum (w/w flour basis) reduced the bread crumb firmness and delayed the staling process of the Taftoon bread. X-ray diffraction study also confirmed this result.

  12. Dilute solution, flow behavior, thixotropy and viscoelastic characterization of cress seed (Lepidium sativum) gum fractions

    DEFF Research Database (Denmark)

    Razmkhah, Somayeh; Razavi, Seyed Mohammad Ali; Mohammadifar, Mohammad Amin

    2017-01-01

    In this study, rheological properties of cress seed gum (CSG) and its fractions (F1, F2, F3; fractionated using stepwise extraction with water) were investigated. Cress seed gum and its fractions revealed random coil conformation in dilute regimes; chain flexibility and intrinsic viscosity...... indicated that CSG and the fractions exhibited significantly different rheological properties....

  13. Unveiling the Sources of Chromium in Pictorialist Photographs: Gum-Dichromate Process or Paper Sizing?

    DEFF Research Database (Denmark)

    Vila, Anna; Centeno, Silvia A; Kennedy, Nora W

    2015-01-01

    For this issue of Hand Papermaking devoted to paper sizing, we offer a review and extension of pertinent results obtained in our investigations of the gum-dichromate photographic process, commonly known as the gum-bichromate process.1 We have published three articles to date on our findings; this...

  14. Gum chewing improves adolescents’ math performance in an SAT preparatory course

    Science.gov (United States)

    The purpose of the current study was to determine the effect of gum chewing on students’ performance in a preparatory course for the Scholastic Aptitude Test (SAT). A total of 182 adolescents enrolled in an SAT preparatory class were randomized into one of two treatments: 1) gum chewing condition (G...

  15. Gum Disease by the Numbers | NIH MedlinePlus the Magazine

    Science.gov (United States)

    ... us Gum Disease by the Numbers Gum (or periodontal) disease is one of the leading threats to dental health. It's typically caused by poor brushing and flossing habits that allow plaque—a sticky film of bacteria—to build up on teeth and harden. In ...

  16. Market-driven production with transaction costs outlook: Gum arabic collection systems in Senegal

    NARCIS (Netherlands)

    Mujawamariya, G.; Burger, C.P.J.; Haese, D' M.F.C.

    2015-01-01

    Low returns from marketing of non-timber forest products such as gum arabic restrict the collection of these products. A hypothesis is tested that access to good markets motivates collectors to harvest and market gum arabic. Analyses of the choice of participation in group marketing, sale price,

  17. Vegetation status and socio-economic importance of gum and resin ...

    African Journals Online (AJOL)

    Ethiopian Journal of Biological Sciences ... Abstract. Study on population status, socio-economic importance and threats of gum- and resin-producing plant species was made in Borena, South Wollo, (Ethiopia). ... A total of 14 gum- and resin-bearing plant species representing seven families were recorded. Five of them ...

  18. investigation of the effect of zinc oxide-modified gum arabic on polar ...

    African Journals Online (AJOL)

    BARTH EKWUEME

    Gum Arabic solution, a water-based adhesive, was modified with zinc oxide filler and the formulation was applied on wood, ceramic, glass and textile substrates. A strip of paper was used as a common adherent to all the substrates. Zinc oxide increased the viscosity of 30wt% gum Arabic solution and increased bond ...

  19. Investigation of the effect of zinc oxide-modified gum Arabic on polar ...

    African Journals Online (AJOL)

    Gum Arabic solution, a water-based adhesive, was modified with zinc oxide filler and the formulation was applied on wood, ceramic, glass and textile substrates. A strip of paper was used as a common adherent to all the substrates. Zinc oxide increased the viscosity of 30wt% gum Arabic solution and increased bond ...

  20. Economic analysis of deforestation : the case of the gum Arabic belt in Sudan

    NARCIS (Netherlands)

    Rahim, A.

    2006-01-01

    Keywords: Gum Arabic; Deforestation; Entry and Exit; Real options Drought; Socio-economic, Oligopoly; Interdependent markets; Stackelberg.The gum arabic belt inSudanoffered in the past an

  1. Gas chromatographic-mass spectrometric characterisation of plant gums in samples from painted works of art.

    Science.gov (United States)

    Bonaduce, Ilaria; Brecoulaki, Hariclia; Colombini, Maria Perla; Lluveras, Anna; Restivo, Vincenzo; Ribechini, Erika

    2007-12-21

    This paper presents an analytical GC-MS procedure to study the chemical composition of plant gums, determining aldoses and uronic acids in one step. The procedure is based on the silylation of aldoses and uronic acids, released from plant gums by microwave assisted hydrolysis, and previously converted into the corresponding diethyl-dithioacetals and diethyl-dithioacetal lactones. Using this method only one peak for each compound is obtained, thus providing simple and highly reproducible chromatograms. The analytical procedure was optimised using reference samples of raw plant gums (arabic, karaya, ghatti, guar, locust bean and tragacanth, cherry, plum and peach gums), commercial watercolours and paint layers prepared according to ancient recipes at the Opificio delle Pietre Dure of Florence (Italy). To identify gum media in samples of unknown composition, a decisional schema for the gum identification and the principal component analysis of the relative sugar percentage contents were employed. The procedure was used to study samples collected from wall paintings from Macedonian tombs (4th-3rd centuries bc) and from the Mycenaean "Palace of Nestor" (13th century bc) in Pylos, Greece. The presence of carbohydrates was ascertained and plant gum binders (fruit and a mixture of tragacanth and fruit tree gums) were identified in some of the samples.

  2. Economic incentives for abandoning or expanding gum arabic production in Sudan

    NARCIS (Netherlands)

    Rahim, A.; Ierland, van E.C.; Wesseler, J.H.H.

    2007-01-01

    In this paper we use a real options approach to analyze farmers' economic incentives to abandon gum production or expand by creating new plantations. Our results indicate that agricultural crops currently provide higher economic benefits as compared to gum agroforestry. However, we show that the

  3. Evaluation of the suspening property of Grewia gum in zinc oxide ...

    African Journals Online (AJOL)

    The suspending property of grewia gum in zinc oxide suspension was evaluated. The gum was extracted by maceration, filtration, precipitation and drying techniques. It was used at 0.3 to 1% w/v as a suspending agent for zinc oxide. Sodiumcarboxymethylcellulose (SCMC) and tragacanth were used as basis for ...

  4. The influence of excessive chewing gum use on headache frequency and severity among adolescents.

    Science.gov (United States)

    Watemberg, Nathan; Matar, Manar; Har-Gil, Miki; Mahajnah, Muhammad

    2014-01-01

    Excessive gum-chewing is underreported as a headache precipitant in children and adolescents. We evaluated the influence of daily excessive gum-chewing in older children and teenagers with chronic headache, emphasizing the impact of habit discontinuation and its reintroduction. Patients with chronic headache and excessive gum-chewing were consecutively recruited and asked to fill questionnaire pertaining headache characteristics, potential triggers, family history of headaches, and gum-chewing habits. These individuals were classified into four groups depending on the number of daily hours of gum-chewing. All children discontinued chewing for 1 month, reintroduced the habit, and were reinterviewed after 2 to 4 weeks. Thirty patients (25 girls) were recruited. Median age was 16 years. Most had migraine-like headaches. Following gum-chewing discontinuation, 26 reported significant improvement, including headache resolution in 19. All 20 patients reinstituting the habit reported symptom relapse within days. Duration of headache before discontinuation and the number of daily hours of chewing had no influence on the response to habit discontinuation. Excessive daily gum-chewing may be associated with chronic headache and should get more attention in the medical literature. Physician and patient awareness of this association could have a meaningful impact on the quality of life of children and adolescents with chronic headache who chew gum excessively. Copyright © 2014 Elsevier Inc. All rights reserved.

  5. Potential benefits of chewing gum for the delivery of oral therapeutics and its possible role in oral healthcare

    NARCIS (Netherlands)

    Wessel, Stefan W.; van der Mei, Henny C.; Maitra, Amarnath; Dodds, Michael W. J.; Busscher, Henk J.

    2016-01-01

    Introduction: Over the years, chewing gum has developed from a candy towards an oral health-promoting nutraceutical. This review summarizes evidence for the oral health benefits of chewing gum, emphasizing identification of active ingredients in gum that facilitate prevention and removal of oral

  6. Pressure production in oral vestibule during gum chewing.

    Science.gov (United States)

    Nishiura, M; Ono, T; Yoshinaka, M; Fujiwara, S; Yoshinaka, M; Maeda, Y

    2015-12-01

    The aim of this study was to record oral vestibule pressure (OVP) by the lip and cheek contraction during gum chewing, to examine the characteristics of these pressures and coordination between the OVP and jaw movement. The subjects were eight healthy adult men (mean age of 29·3 ± 3·3 years). An experimental plate that incorporated four pressure sensors on the midline of the upper jaw (Ch. 1), upper right canine (Ch. 2), upper right first molar (Ch. 3) and upper left first molar (Ch. 4) was used for measuring OVP. The right masseter electromyogram (EMG) was recorded simultaneously. Subjects chewed gum on the right side 20 times, and eight consecutive strokes were used for the analysis of the sequential order, maximal magnitude and duration of each OVP. Onset of OVP was observed at the molar on the non-chewing side (Ch. 4) before chewing side (Ch. 3), and offset was largely simultaneous at each site. On the chewing side (Chs. 1-3), OVP onset during the interval of EMG activity reached to the peak around the end of interval and offset in the duration of EMG activity. The maximal pressure was significantly larger at Chs. 1-3 than at Ch. 4, but no significant differences were observed in duration of pressure among each site. These results suggest that OVP is coordinated with jaw movement during gum chewing, and larger pressure is produced on the chewing side than on the non-chewing side. Our findings are quantitative indices for the evaluation of lip and cheek function during mastication. © 2015 John Wiley & Sons Ltd.

  7. Manilkara zapota (Linn.) Seeds: A Potential Source of Natural Gum.

    Science.gov (United States)

    Singh, Sudarshan; Bothara, Sunil B

    2014-01-01

    Mucilage isolated from seeds of Manilkara zapota (Linn.) P. Royen syn. is a plant growing naturally in the forests of India. This mucilage is yet to be commercially exploited, and characterized as polymer. Various physicochemical methods like particle size analysis, scanning electron microscopy, thermal analysis, gel permeation chromatography, X-ray diffraction spectrometry, zeta potential, Fourier transform infrared spectroscopy, and nuclear magnetic resonance spectroscopy have been employed to characterize this gum in the present study. Particle size analyses suggest that mucilage has particle size in nanometer. Scanning electron microscopy analysis suggests that the mucilage has irregular particle size. The glass transition temperature of the gum was observed to be 138°C and 136°C by differential scanning calorimetry and differential thermal analysis, respectively. The thermogravimetric analysis suggested that mucilage had good thermal stability. The average molecular weight of mucilage was determined to be 379180, by gel permeation chromatography, while the viscosity of mucilage was observed to be 219.1 cP. The X-ray diffraction spectrometry pattern of the mucilage indicates a completely amorphous structure. Elemental analysis of the gum revealed the contents of carbon, hydrogen, nitrogen, and sulfur to be 80.9 (%), 10.1 (%), 1.58 (%), and 512 (mg/kg), respectively. Mucilage had specific content of calcium, magnesium, potassium, lower concentrations of aluminum, cadmium, cobalt, lead, and nickel. The major functional groups identified from FT-IR spectrum include 3441 cm(-1) (-OH), 1660 cm(-1) (Alkenyl C-H & C=C Stretch), 1632 cm(-1) (-COO-), 1414 cm(-1) (-COO-), and 1219 cm(-1) (-CH3CO). Analysis of mucilage by paper chromatography and 1D NMR, indicated the presence of rhamnose, xylose, arabinose, mannose, and fructose.

  8. Hydrolysis of native and heat-treated starches at sub-gelatinization temperature using granular starch hydrolyzing enzyme.

    Science.gov (United States)

    Uthumporn, U; Shariffa, Y N; Karim, A A

    2012-03-01

    The effect of heat treatment below the gelatinization temperature on the susceptibility of corn, mung bean, sago, and potato starches towards granular starch hydrolysis (35°C) was investigated. Starches were hydrolyzed in granular state and after heat treatment (50°C for 30 min) by using granular starch hydrolyzing enzyme for 24 h. Hydrolyzed heat-treated starches showed a significant increase in the percentage of dextrose equivalent compared to native starches, respectively, with corn 53% to 56%, mung bean 36% to 47%, sago 15% to 26%, and potato 12% to 15%. Scanning electron microscopy micrographs showed the presence of more porous granules and surface erosion in heat-treated starch compared to native starch. X-ray analysis showed no changes but with sharper peaks for all the starches, suggested that hydrolysis occurred on the amorphous region. The amylose content and swelling power of heat-treated starches was markedly altered after hydrolysis. Evidently, this enzyme was able to hydrolyze granular starches and heat treatment before hydrolysis significantly increased the degree of hydrolysis.

  9. Selective depression behavior of guar gum on talc-type scheelite flotation

    Science.gov (United States)

    Zhang, Yong-zhong; Gu, Guo-hua; Wu, Xiang-bin; Zhao, Kai-le

    2017-08-01

    The depression behavior and mechanism of guar gum on talc-type scheelite flotation were systematically investigated by flotation experiments, adsorption tests, zeta-potential measurements, and infrared spectroscopic analyses. The flotation results for monominerals, mixed minerals, and actual mineral samples indicated that guar gum exhibited much higher selective depression for talc than for scheelite. Bench-scale closed-circuit tests showed that a tungsten concentrate with a WO3 grade of 51.43% and a WO3 recovery of 76.18% was obtained. Adsorption tests, zeta-potential measurements, and infrared spectral analyses confirmed that guar gum absorbed more strongly onto the talc surface than onto the scheelite surface because of chemisorption between guar gum and talc. This chemisorption is responsible for the guar gum's highly selective depression for talc and small depression for scheelite. The flotation results provide technical support for talc-type scheelite flotation.

  10. Influence of gamma radiation on the physicochemical and rheological properties of sterculia gum polysaccharides

    Science.gov (United States)

    Singh, Baljit; Sharma, Vikrant

    2013-11-01

    Keeping in view the influence of gamma radiation on the physiochemical properties of the polysaccharides and their importance in the food and pharmaceutical industry, in the present study attempt has been made to investigate the effects of absorbed dose on FTIR, XRD, SEMs, absorbance, pH, solubility, water absorption capacity, emulsion stability and rheology of sterculia gum. Increase in solubility and decrease in swellability of gum has been observed on increasing the absorbed dose. The emulsion stability has improved for the gum sample irradiated with total dose of 8.1±0.2 kGy. Apparent viscosity of gum solution first increased with increase in dose from 0 to 8.1±0.2 kGy than decreased with regular trends with further increase in total absorbed dose. Flow behavior of gum solution shifted to Newtonian from non-Newtonian with increasing the dose.

  11. [Analysis of constituents of ester-type gum bases used as natural food additives].

    Science.gov (United States)

    Tada, Atsuko; Masuda, Aino; Sugimoto, Naoki; Yamagata, Kazuo; Yamazaki, Takeshi; Tanamoto, Kenichi

    2007-12-01

    The differences in the constituents of ten ester-type gum bases used as natural food additives in Japan (urushi wax, carnauba wax, candelilla wax, rice bran wax, shellac wax, jojoba wax, bees wax, Japan wax, montan wax, and lanolin) were investigated. Several kinds of gum bases showed characteristic TLC patterns of lipids. In addition, compositions of fatty acid and alcohol moieties of esters in the gum bases were analyzed by GC/MS after methanolysis and hydrolysis, respectively. The results indicated that the varieties of fatty acids and alcohols and their compositions were characteristic for each gum base. These results will be useful for identification and discrimination of the ester-type gum bases.

  12. The management of xerostomia in patients on haemodialysis: comparison of artificial saliva and chewing gum.

    Science.gov (United States)

    Bots, Casper P; Brand, Henk S; Veerman, Enno C I; Valentijn-Benz, Marianne; Van Amerongen, Barbara M; Nieuw Amerongen, Arie V; Valentijn, Robert M; Vos, Pieter F; Bijlsma, Joost A; Bezemer, Pieter D; ter Wee, Piet M

    2005-04-01

    Many patients on haemodialysis (HD) therapy suffer from a dry mouth and xerostomia. This can be relieved by mechanical and gustatory stimulation or palliative care. The aim of this crossover study was to investigate the effect and preferences of a sugar-free chewing gum (Freedent White) and a xanthan gum-based artificial saliva (Xialine) in the management of xerostomia in chronic HD patients. Sixty-five HD patients participated in a 6-week crossover trial. The artificial saliva was rated significantly lower than the chewing gum for effectiveness, taste and a global assessment. No preference differences were found for gender and age, although older subjects rated the artificial saliva with a higher mark. Thirty-nine subjects (60%) preferred chewing gum, 15% (n=10) preferred the artificial saliva. Therefore, both chewing gum and artificial saliva could play an important role in the palliative care of xerostomia in HD patients.

  13. Study of the nanostructure of Gum Metal using energy-filtered transmission electron microscopy

    International Nuclear Information System (INIS)

    Yano, T.; Murakami, Y.; Shindo, D.; Kuramoto, S.

    2009-01-01

    The nanostructure of Gum Metal, which has many anomalous mechanical properties, was investigated using transmission electron microscopy with energy filtering. A precise analysis of the weak diffuse electron scattering that was observed in the electron diffraction patterns of the Gum Metal specimen revealed that Gum Metal contains a substantial amount of the nanometer-sized ω phase. The morphology of the ω phase appeared to have a correlation with the faulting in the {2 1 1} planes, which are one of the characteristic lattice imperfections of the Gum Metal specimen. It is likely that the nanometer-sized ω phase may be a type of obstacle related to the restriction of the dislocation movement, which has been a significant problem in research on Gum Metal

  14. Synthesis, physico-chemical and biomedical applications of sulfated Aegle marmelos gum: Green chemistry approach

    Directory of Open Access Journals (Sweden)

    Manish Jindal

    2017-05-01

    Full Text Available The present investigation was aimed at obtaining a sulfated derivative of gum obtained from partially ripe fruits of Aegle marmelos employing the ultrasonication technique. Elemental analysis and FTIR-ATR studies confirmed successful sulfation. The molarity of sulfuric acid exerted maximum influence on the degree of substitution followed by reaction temperature and reaction time. The sulfated derivative showed higher swelling in both acidic and alkaline pH as compared to the unmodified gum. It also possessed higher negative zeta potential, higher viscosity, work of shear, firmness, consistency, cohesiveness and index of viscosity as compared to both unmodified gum as well as sodium alginate. Sulfated derivative was superior to unmodified gum and sodium alginate in terms of antimicrobial and anticoagulant activities. The sulfated sample appears to be a potential substitute over the unmodified gum sample and sodium alginate for modulating the physicochemical properties of food and drug release dosage forms.

  15. Enzymatic depolymerization of gum Tragacanth: Bifidogenic potential of low molecular weight oligosaccharides

    DEFF Research Database (Denmark)

    Ahmadi Gavlighi, Hassan; Michalak, Malwina; Meyer, Anne S.

    2013-01-01

    Gum tragacanth derived from the plant “goat’s horn” (Astragalus sp.) has a long history of use as a stabilizing, viscosity-enhancing agent in food emulsions. The gum contains pectinaceous arabinogalactans and fucose-substituted xylogalacturonans. In this work, gum tragacanth from Astragalus...... and galactose content. The growth-stimulating potential of the three enzymatically produced gum tragacanth fractions was evaluated via growth assessment on seven different probiotic strains in single culture fermentations on: Bifidobacterium longum subsp. longum (2 strains), B. longum subsp. infantis (3 strains...... that on galactan (control). HAG3 completely inhibited the growth of the Cl. perfringens strain. Tragacanth gum is thus a potential source of prebiotic carbohydrates that exert no viscosity effects and which may find use as natural functional food ingredients....

  16. The mechanism of strength and deformation in Gum Metal

    International Nuclear Information System (INIS)

    Furuta, T.; Kuramoto, S.; Morris, J.W.; Nagasako, N.; Withey, E.; Chrzan, D.C.

    2013-01-01

    Gum Metal” refers to β-Ti alloys that achieve exceptional elastic elongation and, with a specific alloy composition, appear to deform via a dislocation-free mechanism involving elastic instability at the limit of strength. This paper describes the current status of research on its strength, deformation mechanism and the possible role of stress-induced martensite. The theoretical basis for deformation at ideal strength is presented. The relevant experimental data is then discussed, including ex situ nanoindentation behavior and in situ pillar compression observed by transmission electron microscopy

  17. Estimative of relative stiffness of the exudate gum polysaccharides

    International Nuclear Information System (INIS)

    Oliveira, Marilia A.; Paula, Regina C.M.

    2001-01-01

    The Smidsrod empirical stiffness parameter (B) of A. occidentale and A. lebbeck gum were determined using the correlation of intrinsic viscosity [η] with ionic strength. The B value of 0.204 and 0.193 found respectively for A. occidentale and A. lebbeck suggests a flexible the molecule. The ionic strength has a greater influence on the [η]. The decrease of [η] increase of I, from 0.01 M to 0.1 M of NaCl, is higher for A. lebbeck (89%) than for A. occidentale (19%). (author)

  18. Switching between chewing-gum and no-gum at learning and retrieval does not accentuate error production in free recall

    OpenAIRE

    Miles, C.; Johnson, A.J.

    2010-01-01

    Three experiments compared chewing gum to a no gum condition to examine further the finding (Anderson, Berry, Morse & Diotte, 2005) that switching flavour between learning and recall encourages error production independently of free recall. In order to encourage error production, participants in Experiment 1 were told to guess responses at recall, participants in Experiment 2 were required to recall categorised word lists and in Experiment 3 participants repeated the same learning-recall comb...

  19. KARAKTERISTIK EMULSI SANTAN DAN MINYAK KEDELAI YANG DITAMBAH GUM ARAB DAN SUKROSA ESTER [Emulsion Characteristics of Coconut Milk and Soybean Oil Added with Gum Arabic and Sucrose Ester

    Directory of Open Access Journals (Sweden)

    Laksmi Hartayanie

    2015-07-01

    Full Text Available High saturated fatty acid content in coconut milk can be reduced by adding unsaturated fat. Pretreatment such as pasteurisation, homogenization or stabilizer and emulsifier addition are essential to prevent emulsion deterioration that could happen in few hours. This study aimed to determine the most appropriate combination of gum arabic and sucrose ester to produce good emulsion stability based on its physical and chemical characteristics. Furthermore this study also aimed to determine correlation between creaming index and other characteristics of coconut milk emulsion. Emulsion stability of mixed coconut milk in sterile glass bottles was observed for 7 days under 23-24°C. Stabilizer and emulsifier added were gum arabic and sucrose ester in five combinations, i.e. 6% gum arabic, 0.3% sucrose ester, 6% gum arabic + 0.3% sucrose ester, 3% gum arabic + 0.15% sucrose ester and 4.5% gum arabic + 0.225% sucrose ester. The physical characteristics evaluated were creaming index, total color change, viscosity and droplet distribution, while the chemical characteristics observed included pH, TBA value, and protein content. Data were analyzed by One Way Anova at 95% significant level to determine the differences among treatments. Bivariate Pearson Correlation was used in order to determine the interaction among sample characteristics. The data showed that, gum arabic and sucrose ester can maintain the emulsion stability. A combination of 4.5% gum arabic and 0.225% sucrose ester provided the best physicochemical characteristics with the lowest creaming index and decreased viscosit, and uniform droplet distribution.

  20. Características físico-químicas e utilização em alimentos de amidos modificados por tratamento oxidativo Obtention, physicochemical characterization and applications in foods of starches modified by oxidative treatment

    Directory of Open Access Journals (Sweden)

    Marianne Ayumi Shirai

    2007-06-01

    Full Text Available A utilização de amidos modificados em alimentos tem sido uma alternativa para melhorar as características que os amidos nativos não podem conferir. Os objetivos deste trabalho foram: avaliar características físico-químicas de amidos modificados com peróxido de hidrogênio, utilizar os amidos obtidos para a elaboração de doce de leite e bala de goma americana e verificar a aceitação sensorial destes produtos. Para obtenção das amostras modificadas, os amidos foram suspensos em solução de Fe2SO4.7H2O 0,01% e, em seguida, adicionou-se peróxido de hidrogênio 1,25%, ajustou-se o pH para 3,0, deixou-se reagir a 45 °C/15 minutos, lavou-se e secou-se a amostra em estufa de ventilação forçada a 45 °C/24 horas. Os amidos modificados apresentaram maior expansão, conteúdo de carboxilas, poder redutor e susceptibilidade à sinérese. Em relação à viscosidade aparente, verificou-se que com a modificação química houve diminuição no pico de viscosidade, especialmente quando as amostras foram analisadas em pH 7,0. A análise sensorial do doce de leite revelou que houve preferência pelas amostras elaboradas com amido de mandioquinha-salsa modificado e com o amido de milho regular ácido-modificado. A bala de goma produzida com amido de mandioquinha-salsa modificado ocupou o segundo lugar entre a preferência dos julgadores.The use of modified starches in foods is made to improve characteristics that the native cannot confer. The objective of this work was to evaluate physicochemical characteristics of starches from several botanical sources after chemical modification with H2O2 considering technological properties of interest to the food industry. The modified starches were used in dulce de leche and starch gum and the sensorial acceptance of these products was verified. The chemical treatment included the suspension of the native starches in a 0.01% Fe2SO4, followed by addition of 1.25% H2O2 at pH 3.0 and reaction time of 15 min

  1. Effect of maize starch concentration in the diet on starch and cell wall digestion in the dairy cow.

    Science.gov (United States)

    van Vuuren, A M; Hindle, V A; Klop, A; Cone, J W

    2010-06-01

    An in vivo experiment was performed to determine the effect of level of maize starch in the diet on digestion and site of digestion of organic matter, starch and neutral detergent fibre (NDF). In a repeated change-over design experiment, three cows fitted with a rumen cannula and T-piece cannulae in duodenum and ileum received a low-starch (12% of ration dry matter) and a high-starch (33% of ration dry matter) diet. Starch level was increased by exchanging dried sugar beet pulp by ground maize. After a 2-week adaptation period, feed intake, rumen fermentation parameters (in vivo and in situ), intestinal flows, faecal excretion of organic matter, starch and NDF were estimated. When the high-starch diet was fed, dry matter intake was higher (19.0 kg/day vs. 17.8 kg/day), and total tract digestibility of organic matter, starch and NDF was lower when the low-starch diet was fed. Maize starch concentration had no significant effect on rumen pH and volatile fatty acid concentration nor on the site of digestion of organic matter and starch and rate of passage of ytterbium-labelled forage. On the high-starch diet, an extra 1.3 kg of maize starch was supplied at the duodenum in relation to the low-starch diet, but only an extra 0.3 kg of starch was digested in the small intestine. Digestion of NDF was only apparent in the rumen and was lower on the high-starch diet than on the low-starch diet, mainly attributed to the reduction in sugar beet pulp in the high-starch diet. It was concluded that without the correction for the reduction in NDF digestion in the rumen, the extra supply of glucogenic (glucose and propionic acid) and ketogenic nutrients (acetic and butyric acid) by supplemented starch will be overestimated. The mechanisms responsible for these effects need to be addressed in feed evaluation.

  2. Development of oxidised and heat-moisture treated potato starch film.

    Science.gov (United States)

    Zavareze, Elessandra da Rosa; Pinto, Vânia Zanella; Klein, Bruna; El Halal, Shanise Lisie Mello; Elias, Moacir Cardoso; Prentice-Hernández, Carlos; Dias, Alvaro Renato Guerra

    2012-05-01

    This study investigated the effects of sodium hypochlorite oxidation and a heat-moisture treatment of potato starch on the physicochemical, pasting and textural properties of potato starches in addition to the water vapour permeability (WVP) and mechanical properties of potato starch films produced from these starches. The carbonyl contents, carboxyl contents, swelling power, solubility, pasting properties and gel texture of the native, oxidised and heat-moisture treated (HMT) starches were evaluated. The films made of native, oxidised and HMT starches were characterised by thickness, water solubility, colour, opacity, mechanical properties and WVP. The oxidised and HMT starches had lower viscosity and swelling power compared to the native starch. The films produced from oxidised potato starch had decreased solubility, elongation and WVP values in addition to increased tensile strength compared to the native starch films. The HMT starch increased the tensile strength and WVP of the starch films compared to the native starch. Copyright © 2011 Elsevier Ltd. All rights reserved.

  3. Graft polymerization of vinyl acetate onto starch. Saponification to starch-g-poly(vinyl alcohol)

    International Nuclear Information System (INIS)

    Fanta, G.F.; Burr, R.C.; Doane, W.M.; Russell, C.R.

    1979-01-01

    Graft polymerizations of vinyl acetate onto granular cornstarch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinyl acetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. Over half of the polymer was present as ungrafted poly(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficency. Grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate--methyl methacrylate was carried out near 0 0 C; although conversion of monomers to polymer was low and grafted polymer contained 40 to 50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch-g-poly(vinyl acetate) to starch-g-poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch-g-poly(vinyl alcohol) in hot water was less than 50; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch-g-poly

  4. Studies on rye starch properties and modification. Pt. 1. Composition and properties of rye starch granules

    Energy Technology Data Exchange (ETDEWEB)

    Schierbaum, F; Radosta, S; Richter, M; Kettlitz, B [Zentralinstitut fuer Ernaehrung, Potsdam (Germany); Gernat, C [Zentralinstitut fuer Molekularbiologie, Berlin (Germany)

    1991-09-01

    Rye is considered as a potential raw material for starch industry. Starting from a survey of technical procedures of isolating starches from rye-flour and -grits investigations will be reported, which were performed on pilot plant- and laboratory-isolated rye starches. The present paper deals with its granule appearance and composition. A distribution of granule size between small granules ({<=} 10 {mu}m - 15%) and large granules ({>=} 11 ... {<=} 40 {mu}m = 85%) is typical for the totality of the starches. Differing distributions depend on the conditions of isolation: The entity of starch containing samples resulted from the latoratory procedures under investigation. Large-granule starch preparations were isolated in the pilot plant: The centrifuge-overflow contains the small-granule fraction which is high in impurities. Granule crystallinity amounts to 16%. The crystalline component - like in wheat and triticale starches - consists predominantly of A-polymorph - with up to 9% of the B-type. The isotherms of water exchange are of the cereal type. The contents of minor constituents largely relate to the small granule fraction which assembles the majority of crude protein, pentosans and lipids, which are difficult to remove. Lipid components in all fractions influence the results of linear chain-iodine interactions and they must be removed to proceed from apparent to absolute polysaccharide indices. The absolute amylose contents amount to {approx equal} 25% for large granule samples and to 20-21% for small granule samples. The average chain-length of iodine binding helical regions was determined with 220-240 AGU. (orig.).

  5. Antinociceptive activity of Astragalus gummifer gum (gum tragacanth) through the adrenergic system: A in vivo study in mice.

    Science.gov (United States)

    Bagheri, Seyyed Majid; Keyhani, Leila; Heydari, Mehrangiz; Dashti-R, Mohammad Hossein

    2015-01-01

    In Iranian traditional medicine, gum obtained from Astragalus gummifer and some other species of Astragalus was used as analgesic agent. In this study, we investigated the antinociceptive effect of several concentrations (125, 250, and 500 μg/kg body weight) of Astragalus gummifer gum (AGG) on thermal and acetic acid induced pain in mice. AGG was dissolved in distillated water and injected i.p to male mice 15 minute before the onset of experiment. Writhing and hot-plate tests were applied to study the analgesic effect of AGG and compared with that of diclofenac sodium (30 mg/kg, i.p.) or morphine (8 mg/kg, i.p). To investigate the mechanisms involved in antinociception, yohimbine, naloxone, glibenclamide, and theophylline were used in writhing test. These drugs were injected intraperitoneally 15 min before the administration of AGG. The number of writhes were counted in 30 minutes and analyzed. AGG exhibited a significant antinociceptive effect and the most effective dose of AGG was 500 μg/kg. The most maximum possible effect (%MPE) was observed (117.4%) 15 min after drug administration. The %inhibition of acetic acid-induced writhing in AGG 125, 250 and 500 was 47%, 50% and 54% vs %15 of control and 66.3% of diclofenac sodium group. The antinociceptive effect induced by this gum in the writhing test was reversed by the systemic administration of yohimbine (α2-adrenergic antagonist), but naloxone, glibenclamide, and theophylline did not reverse this effect. The findings of this study indicated that AGG induced its antinociceptive through the adrenergic system.

  6. Antinociceptive activity of Astragalus gummifer gum (gum tragacanth through the adrenergic system: A in vivo study in mice

    Directory of Open Access Journals (Sweden)

    Seyyed Majid Bagheri

    2015-01-01

    Full Text Available Background: In Iranian traditional medicine, gum obtained from Astragalus gummifer and some other species of Astragalus was used as analgesic agent. Objective: In this study, we investigated the antinociceptive effect of several concentrations (125, 250, and 500 μg/kg body weight of Astragalus gummifer gum (AGG on thermal and acetic acid induced pain in mice. Materials and Methods: AGG was dissolved in distillated water and injected i.p to male mice 15 minute before the onset of experiment. Writhing and hot-plate tests were applied to study the analgesic effect of AGG and compared with that of diclofenac sodium (30 mg/kg, i.p. or morphine (8 mg/kg, i.p. To investigate the mechanisms involved in antinociception, yohimbine, naloxone, glibenclamide, and theophylline were used in writhing test. These drugs were injected intraperitoneally 15 min before the administration of AGG. The number of writhes were counted in 30 minutes and analyzed. Results: AGG exhibited a significant antinociceptive effect and the most effective dose of AGG was 500 μg/kg. The most maximum possible effect (%MPE was observed (117.4% 15 min after drug administration. The %inhibition of acetic acid-induced writhing in AGG 125, 250 and 500 was 47%, 50% and 54% vs %15 of control and 66.3% of diclofenac sodium group. The antinociceptive effect induced by this gum in the writhing test was reversed by the systemic administration of yohimbine (α2 -adrenergic antagonist, but naloxone, glibenclamide, and theophylline did not reverse this effect. Conclusions: The findings of this study indicated that AGG induced its antinociceptive through the adrenergic system.

  7. Structure, morphology and functionality of acetylated and oxidised barley starches.

    Science.gov (United States)

    El Halal, Shanise Lisie Mello; Colussi, Rosana; Pinto, Vânia Zanella; Bartz, Josiane; Radunz, Marjana; Carreño, Neftali Lenin Villarreal; Dias, Alvaro Renato Guerra; Zavareze, Elessandra da Rosa

    2015-02-01

    Acetylation and oxidation are chemical modifications which alter the properties of starch. The degree of modification of acetylated and oxidized starches is dependent on the catalyst and active chlorine concentrations, respectively. The objective of this study was to evaluate the effect of acetylation and oxidation on the structural, morphological, physical-chemical, thermal and pasting properties of barley starch. Barley starches were acetylated at different catalyst levels (11%, 17%, and 23% of NaOH solution) and oxidized at different sodium hypochlorite concentrations (1.0%, 1.5%, and 2.0% of active chlorine). Fourier-transformed infrared spectroscopy (FTIR), X-ray diffractograms, thermal, morphological, and pasting properties, swelling power and solubility of starches were evaluated. The degree of substitution (DS) of the acetylated starches increased with the rise in catalyst concentration. The percentage of carbonyl (CO) and carboxyl (COOH) groups in oxidized starches also increased with the rise of active chlorine level. The presence of hydrophobic acetyl groups, carbonyl and carboxyl groups caused a partial disorganization and depolymerization of starch granules. The structural, morphological and functional changes in acetylated and oxidized starches varied according to reaction conditions. Acetylation makes barley starch more hydrophobic by the insertion of acetyl groups. Also the oxidation promotes low retrogradation and viscosity. All these characteristics are important for biodegradable film production. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Microstructure, thermal properties and crystallinity of amadumbe starch nanocrystals.

    Science.gov (United States)

    Mukurumbira, Agnes; Mariano, Marcos; Dufresne, Alain; Mellem, John J; Amonsou, Eric O

    2017-09-01

    Amadumbe (Colocasia esculenta), commonly known as taro is a tropical tuber that produces starch-rich underground corms. In this study, the physicochemical properties of starch nanocrystals (SNC) prepared by acid hydrolysis of amadumbe starches were investigated. Two varieties of amadumbe corms were used for starch extraction. Amadumbe starches produced substantially high yield (25%) of SNC's. These nanocrystals appeared as aggregated and individual particles and possessed square-like platelet morphology with size: 50-100nm. FTIR revealed high peak intensities corresponding to OH stretch, CH stretch and H 2 O bending vibrations for SNCs compared to their native starch counterparts. Both the native starch and SNC exhibited the A-type crystalline pattern. However, amadumbe SNCs showed higher degree of crystallinity and slightly reduced melting temperatures than their native starches. Amadumbe SNCs presented similar thermal decomposition property as their native starches. Amadumbe starch nanocrystals may have potential application in biocomposite films due to their square-like platelet morphology. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. The future of starch bioengineering: GM microorganisms or GM plants?

    Directory of Open Access Journals (Sweden)

    Kim Henrik eHebelstrup

    2015-04-01

    Full Text Available Plant starches regularly require extensive modification to permit subsequent applications. Such processing is usually done by the use of chemical and/or physical treatments. The use of recombinant enzymes produced by large-scale fermentation of GM microorganisms is increasingly used in starch processing and modification, sometimes as an alternative to chemical or physical treatments. However, as a means to impart the modifications as early as possible in the starch production chain, similar recombinant enzymes may also be expressed in planta in the developing starch storage organ such as in roots, tubers and cereal grains to provide a GM crop as an alternative to the use of enzymes from GM microorganisms. We here discuss these techniques in relation to important structural features and modifications of starches such as: starch phosphorylation, starch hydrolysis, chain transfer/branching and novel concepts of hybrid starch-based polysaccharides. In planta starch bioengineering is generally challenged by yield penalties and inefficient production of the desired product. However in some situations, GM crops for starch bioengineering without deleterious effects have been achieved.

  10. Starch Characteristics Linked to Gluten-Free Products

    Directory of Open Access Journals (Sweden)

    Stefan W. Horstmann

    2017-04-01

    Full Text Available The increasing prevalence of coeliac disease (CD and gluten-related disorders has led to increasing consumer demand for gluten-free products with quality characteristics similar to wheat bread. The replacement of gluten in cereal-based products remains a challenge for scientists, due to its unique role in network formation, which entraps air bubbles. When gluten is removed from a flour, starch is the main component left. Starch is used as gelling, thickening, adhesion, moisture-retention, stabilizing, film forming, texturizing and anti-staling ingredient. The extent of these properties varies depending on the starch source. The starches can additionally be modified increasing or decreasing certain properties of the starch, depending on the application. Starch plays an important role in the formulation of bakery products and has an even more important role in gluten-free products. In gluten-free products, starch is incorporated into the food formulation to improve baking characteristics such as the specific volume, colour and crumb structure and texture. This review covers a number of topics relating to starch; including; an overview of common and lesser researched starches; chemical composition; morphology; digestibility; functionality and methods of modification. The emphasis of this review is on starch and its properties with respect to the quality of gluten-free products.

  11. Starch Characteristics Linked to Gluten-Free Products.

    Science.gov (United States)

    Horstmann, Stefan W; Lynch, Kieran M; Arendt, Elke K

    2017-04-06

    The increasing prevalence of coeliac disease (CD) and gluten-related disorders has led to increasing consumer demand for gluten-free products with quality characteristics similar to wheat bread. The replacement of gluten in cereal-based products remains a challenge for scientists, due to its unique role in network formation, which entraps air bubbles. When gluten is removed from a flour, starch is the main component left. Starch is used as gelling, thickening, adhesion, moisture-retention, stabilizing, film forming, texturizing and anti-staling ingredient. The extent of these properties varies depending on the starch source. The starches can additionally be modified increasing or decreasing certain properties of the starch, depending on the application. Starch plays an important role in the formulation of bakery products and has an even more important role in gluten-free products. In gluten-free products, starch is incorporated into the food formulation to improve baking characteristics such as the specific volume, colour and crumb structure and texture. This review covers a number of topics relating to starch; including; an overview of common and lesser researched starches; chemical composition; morphology; digestibility; functionality and methods of modification. The emphasis of this review is on starch and its properties with respect to the quality of gluten-free products.

  12. Application of oxidized starch in bake-only chicken nuggets.

    Science.gov (United States)

    Purcell, Sarah; Wang, Ya-Jane; Seo, Han-Seok

    2014-05-01

    There is a need to reduce the fat content in fried foods because of increasing health concerns from consumers. Oxidized starches have been utilized in many coating applications for their adhesion ability. However, it is not known if they perform similarly in bake-only products. This study investigated the application of oxidized starch in bake-only chicken nuggets. Oxidized starches were prepared from 7 starches and analyzed for gelatinization and pasting properties. Chicken nuggets were prepared using batter containing wheat flour, oxidized starch, salt, and leavening agents prior to steaming, oven baking, freezing, and final oven baking for sensory evaluation. All nuggets were analyzed for hardness by a textural analyzer, crispness by an acoustic sound, and sensory characteristics by a trained panel. The oxidation level used in the study did not alter the gelatinization temperature of most starches, but increased the peak pasting viscosity of both types of corn and rice starches and decreased that of tapioca and potato starches. There were slight differences in peak force and acoustic reading between some treatments; however, the differences were not consistent with starch type or amylose content. There was no difference among the treatments as well as between the control with wheat flour and the treatments partially replaced with oxidized starches in all sensory attributes of bake-only nuggets evaluated by the trained panel. There is a need to reduce the fat content in fried food, such as chicken nuggets, because of increasing childhood obesity. Oxidized starches are widely used in coating applications for their adhesion ability. This study investigated the source of oxidized starches in steam-baked coated nuggets for their textural and sensorial properties. The findings from this research will provide an understanding of the contributions of starch source and oxidation to the texture and sensory attributes of bake-only nuggets, and future directions to improve

  13. Preparation and Characterization of Some Polyethylene Modified- Starch Biodegradable Films

    International Nuclear Information System (INIS)

    Badrana, A.S.; Ramadanb, A.M.; Ibrahim, N.A.; Kahild, T.; Hussienc, H.A.

    2005-01-01

    Blends of LDPE with soluble starch, wheat flour and commercial starch were prepared by mixing starch (or flour) with styrene then blending the mixture with LDPE, The starch percents vary between 5 and 50% of the total weight. Their physical and mechanical properties were recorded and compared with pure LDPE. It was observed that the increase in starch or wheat flour contents of the mixture was reversibly proportional to the tensile strength and % elongation. Samples were tested for water absorption. All of the samples were insoluble in cold and boiling water. Moisture uptake increased with immersion time and increasing starch content. The changes in the tensile strength of LDPE/starch (or wheat flour) after the course of thermal oxidation was measured. These results show negligible changes in the tensile strength of the control sample as compared to that of the samples containing the additives. Oxidation processes take advantage of the high temperatures (40-50 degree C) and the time. It was also observed that after 10 weeks of soil burial, the mechanical properties of the films decrease, mainly, due to starch removal from the films. Also, for the weight loss a drastic decrease was observed after 10 weeks of soil burial thereafter it preceded slowly. The LDPE/ starch strips showed weight loss after treating with a-amylase this due to hydrolysis and leaching of the starch. The rate of starch hydrolysis increases with the increase in starch content of the sample. The influence of addition of starch on the overall migration of these films, with different food simulant, was studied, at different temperatures (-4 degree. 25 degree and 40 degree C). All values were significantly lower than the upper limit for overall migration set by the EU (10 mg/dirf) for food grade plastics packaging materials

  14. Properties of foam and composite materials made o starch and cellulose fiber

    Science.gov (United States)

    Composite materials were made of starch and cellulose fibers. Pre-gelatinized starch was effective in dispersing pulp fiber in a starch matrix to form a viscous starch/fiber dough. The starch/fiber dough was a useful feedstock for various composite foam and plastic materials. Viscous blends of star...

  15. Gum arabic based composite edible coating on green chillies

    Science.gov (United States)

    Valiathan, Sreejit; Athmaselvi, K. A.

    2018-04-01

    Green chillies were coated with a composite edible coating composed of gum arabic (5%), glycerol (1%), thyme oil (0.5%) and tween 80 (0.05%) to preserve the freshness and quality of green chillies and thus reduce the cost of preservation. In the present work, the chillies were coated with the composite edible coating using the dipping method with three dipping times (1, 3 and 5 min). The physicochemical parameters of the coated and control chillies stored at room temperature (28±2ºC) were evaluated at regular intervals of storage. There was a significant difference (p≤0.05) in the physicochemical properties between the control chillies and coated chillies with 1, 3 and 5 min dipping times. The coated green chillies showed significantly (p≤0.05) lower weight loss, phenolic acid production, capsaicin production and significantly (p≤0.05) higher retention of ascorbic acid, total chlorophyll content, colour, firmness and better organoleptic properties. The composite edible coating of gum arabic and thyme oil with 3 min dipping was effective in preserving the desirable physico-chemical and organoleptic properties of the green chillies up to 12 days, compared to the uncoated chillies that had a shelf life of 6 days at room temperature.

  16. Franšīzes līgums

    OpenAIRE

    Bērziņš, Artūrs

    2011-01-01

    Bakalaura darba "Franšīzes līgums" mērķis ir jaunā nacionālā tiesiskā regulējuma izpēte, tā atbilstības starptautiskajam regulējumam konstatēšana. Bakalaura darbs sastāv no četrām nodaļām, kurās tiek aplūkots franšīzes līgums un tā būtība, tā atšķirība no citiem civiltieskiem līgumiem, franšīzes attīstība Latvijā un tiesiskā regulējuma pilnveidošana Eiropas Savienības tiesiskā regulējuma ietvaros, kā arī problēmjautājumi un to risinājums. Darba autors nonāk pie secinājuma, ka nolūkā past...

  17. Development of lamivudine containing multiple emulsions stabilized by gum odina

    Directory of Open Access Journals (Sweden)

    Aditya Kumar Jena

    2018-06-01

    Full Text Available In the current study, a multiple emulsion (W/O/W of lamivudine was developed using a new biopolymer, gum odina (GOd to increase bioavailability and patient compliances. GOd was employed to stabilize both the interfaces of liquid membrane in both the external and internal aqueous phases. The developed W/O/W multiple emulsion of lamivudine was characterized by analyzing droplet size, zeta potential, polydispersity index (PDI, sedimentation, viscosity, rheological properties, drug entrapment efficiency, in-vitro drug release and stability at various storage conditions. The results obtained were also compared with W/O/W multiple emulsion of lamivudine prepared using Tween 80 (a standard emulsion stabilizer. The drug entrapment efficiency of W/O/W multiple emulsion stabilized using GOd was measured as 91.60 ± 3.66% with sustained lamivudine release over a period of 6 h. Rheological and microscopic examinations indicated long term stability of the developed emulsion prepared using GOd. The results of the current study provide a promising scope to attain sustained drug release through the W/O/W multiple emulsions stabilized by GOd in antiviral therapies. Keywords: Gum odina, Lamivudine, Multiple emulsions

  18. Thermal stability and haemolytic effects of depolymerized guar gum derivatives.

    Science.gov (United States)

    Hussain, Majid; Zahoor, Tahir; Akhtar, Saeed; Ismail, Amir; Hameed, Aneela

    2018-03-01

    The purpose of current study was to purify and partially depolymerize guar gum by β-mannanase, HCl, Ba(OH) 2 actions and subjected to inspect compositional, thermogravimetric analysis (TGA) and haemolytic activity. Chemical composition revealed mannose and galactose ratio remained un-altered even after process of purification and hydrolysis. TGA thermograms affirmed initial and final decomposition temperature in various zones. Major decomposition stages apparently revealed partially hydrolyzed guar gum (PHGG) exhibited better heat stable properties having more zones of degradation than crude one. Furthermore, all guar fractions (2.5-250 mg/mL) were subjected to haemolysis to evaluate toxic effects during process of hydrolysis. The crude and hydrolyzed guar galactomannans exhibited minor haemolytic activity (1.9 ± 0.03-7.24 ± 0.02%) when compared to 0.1% Triton-X 100 (100% haemolysis) showing no toxic effects to human RBC's. Conclusively, hydrolyzed guar-galactomannans are safe and can be used in food products with improved heat stability.

  19. Study of chemical and physical properties of irradiated Guar Gum

    International Nuclear Information System (INIS)

    Hussein, H. A. S.

    2012-07-01

    This study was carried out to evaluate the effect of different gamma radiation doses to decontamination of micro-organisms present in Guar Gum powder. As well as to study the effect of radiation on the chemical and physical properties of the carbohydrate components of the Gum's material. Two types of samples were used in this study (powder and liquid). All samples were collected from commercially available Guar Gum (G G), which were obtained from the company (Sudanese Guar Gum ltd). Samples putted in polyethylene tightly closed container, then irradiated by applying different doses (2.5, 5, 7.5, 10, 20,30,40,and 50 kGy) from Co-60 source at room temperature in air. And take zero kGy as control. Irradiated powder samples of (2.5, 5, 7.5, 10 kGy) were investigated for contamination by using growth media agar and the result showed that 2.5 kGy is appropriate dose to remove the contamination of the samples. And then analyzed using fourier transform infrared (FTTR) x-ray fluorescence (X RF) and spectroscopy. The FTIR spectroscopy results suggested that there were no major chemical functional group transformation during irradiation. No change occurs by using low dose as 2.5 kGy. Also evaluation impact of radiation on liquid Samples (Aqueous solutions prepared in tow concentration of 1% and 5% wv that is by exposing the samples to the same dose of gamma rays) the effect of irradiation on it were investigated by using ultra violet spectroscopy ( UV.Vis), results showed that low dose has steeply effect in solutions specially in low concentration, it was more pronoun than that in high concentration, high dose has made change similar to that it made in powder. Also for both concentrations of liquid samples and for solutions made of irradiated powder pH measured and viscosity which used in investigations of molecular weight of liquid and powder, comparing the results of impact in the form of powder with the results of effects in the solutions found that the effects of

  20. Characterisation of hydroxypropylated crosslinked sago starch as compared to commercial modified starches

    Directory of Open Access Journals (Sweden)

    Saowakon Wattanachant

    2002-07-01

    Full Text Available The characteristics of hydroxypropylated crosslinked sago starch (HPST were determined and compared with five types of commercial modified starches (CMST in order to evaluate its quality for further applications. The HPST was prepared on a large scale having molar substitution (MS and degree substitution (DS values in the range of 0.038 to 0.045 and 0.004 to 0.005, respectively. The properties of HPST in terms of sediment volume, swelling power, solubility and paste clarity were 15.75%, 16.7, 8.62% and 5.18%T650 , respectively. The MS value, phosphorus content, paste clarity, swelling power and syneresis after six freeze-thaw cycles of HPST when compared to that of commercially available modified starches which are normally used or incorporated in acidic, frozen and canned foods did not differ significantly. The pasting characteristic of HPST exhibited thin to thick viscosity which was similar (P>0.05 to that of commercial hydroxypropylated crosslinked tapioca starch (NAT 8. The acid stability, solubility and freeze-thaw stability of both starches were also similar (P>0.05 but the swelling power of HPST was slightly lower (P<0.05 than that of NAT 8 .

  1. Characteristics of cassava starch fermentation wastewater based on structural degradation of starch granules

    Directory of Open Access Journals (Sweden)

    Juliane Mascarenhas Pereira

    2016-01-01

    Full Text Available ABSTRACT: Sour cassava starch is a naturally modified starch produced by fermentation and sun drying, achieving the property of expansion upon baking. Sour cassava starch' bakery products can be prepared without the addition of yeast and it is gluten free. The fermentation process associated with this product has been well studied, but the wastewater, with high acidity and richness in other organic compounds derived from starch degradation, requires further investigation. In this study, the structure of solids present in this residue was studied, seeking to future applications for new materials. The solids of the wastewater were spray dried with maltodextrin (MD with dextrose equivalent (DE of 5 and 15 and the structure of the powder was evaluated by scanning electron microscopy. A regular structure with a network arrangement was observed for the dried material with MD of 5 DE, in contrast to the original and fermented starches structure, which suggests a regular organization of this new material, to be studied in future applications.

  2. The effect of starch-garlic powder ratio on degradation rate of Gadung starch bioplastic

    Science.gov (United States)

    Mairiza, L.; Mariana; Ramadhany, M.; Feviyussa, C. A.

    2018-03-01

    Bioplastic is one of the solutions for environmental problems caused by plastics waste. Utilization of toxic gadung starch in the manufacturing of bioplastic would be as an alternative, due to gadung bulb has high starch content, and it is still not used optimally. This research aimed to learn about the using of gadung starch-mixed with garlic powder of making biodegradable plastic packaging. Also, to observe the duration of degradation, as a level of biodegradability of plastic film produced. The method used making this bioplastic was casting method. The variables used in this study were the ratios of starch and powdered garlic, were 10:0; 8:2; 6:4, and the concentration of garlic powder were 2%; 4%; 6%; and 8 %. The degradation test was done by soil burial test. The results of the soil burial test shown that the film was more rapidly degraded at ratio of 6: 4 compared to the ratio of 8: 2 and 10: 0. The results shown that bioplastic at the starch-garlic powder ratio of 10: 0 was decomposed in 21 days, at the the ratio of 8:2 was 15 days, while at the ratio of 6:4, the plastic film was degraded in the 11 days.

  3. Cassava starch films containing acetylated starch nanoparticles as reinforcement: Physical and mechanical characterization.

    Science.gov (United States)

    Teodoro, Ana Paula; Mali, Suzana; Romero, Natália; de Carvalho, Gizilene Maria

    2015-08-01

    This paper reports the use of acetylated starch nanoparticles (NPAac) as reinforcement in thermoplastic starch films. NPAac with an average size of approximately 500 nm were obtained by nanoprecipitation. Fourier transform infrared (FTIR) and thermogravimetric analysis (TGA) indicated that NPAac are more thermally stable and essentially amorphous when compared with acetylated starch. Thermoplastic starch films with different proportions of NPAac (0.5, 1.0, 1.5, 10.0%, w/w) were obtained and characterized by scanning electron microscopy (SEM), water vapor permeability (WVP), adsorption isotherms, TGA and mechanical tests. The inclusion of reinforcement caused changes in film properties: WVP was lowered by 41% for film with 1.5% (w/w) of NPAac and moisture adsorption by 33% for film with 10% (w/w) of NPAac; and the Young's modulus and thermal stability were increased by 162% and 15%, respectively, for film with 0.5% (w/w) of NPAac compared to the starch film without the addition of NPAac. Copyright © 2015 Elsevier Ltd. All rights reserved.

  4. Partial characterization of chayotextle starch-based films added with ascorbic acid encapsulated in resistant starch.

    Science.gov (United States)

    Martínez-Ortiz, Miguel A; Vargas-Torres, Apolonio; Román-Gutiérrez, Alma D; Chavarría-Hernández, Norberto; Zamudio-Flores, Paul B; Meza-Nieto, Martín; Palma-Rodríguez, Heidi M

    2017-05-01

    Chayotextle starch was modified by subjecting it to a dual treatment with acid and heating-cooling cycles. This caused a decrease in the content of amylose, which showed values of 30.22%, 4.80%, 3.27% and 3.57% for native chayotextle starch (NCS), starch modified by acid hydrolysis (CMS), and CMS with one (CMS1AC) and three autoclave cycles (CMS3AC), respectively. The percentage of crystallinity showed an increase of 36.9%-62% for NCS and CMS3AC. The highest content of resistant starch (RS) was observed in CMS3AC (37.05%). The microcapsules were made with CMS3AC due to its higher RS content; the total content of ascorbic acid of the microcapsules was 82.3%. The addition of different concentrations of CMS3AC microcapsules (0%, 2.5%, 6.255% and 12.5%) to chayotextle starch-based films (CSF) increased their tensile strength and elastic modulus. The content of ascorbic acid and RS in CSF was ranged from 0% to 59.4% and from 4.84% to 37.05% in the control film and in the film mixed with CMS3AC microcapsules, respectively. Water vapor permeability (WVP) values decreased with increasing concentrations of microcapsules in the films. Microscopy observations showed that higher concentrations of microcapsules caused agglomerations due their poor distribution in the matrix of the films. Copyright © 2017 Elsevier B.V. All rights reserved.

  5. Mixture design of rice flour, maize starch and wheat starch for optimization of gluten free bread quality.

    Science.gov (United States)

    Mancebo, Camino M; Merino, Cristina; Martínez, Mario M; Gómez, Manuel

    2015-10-01

    Gluten-free bread production requires gluten-free flours or starches. Rice flour and maize starch are two of the most commonly used raw materials. Over recent years, gluten-free wheat starch is available on the market. The aim of this research was to optimize mixtures of rice flour, maize starch and wheat starch using an experimental mixture design. For this purpose, dough rheology and its fermentation behaviour were studied. Quality bread parameters such as specific volume, texture, cell structure, colour and acceptability were also analysed. Generally, starch incorporation reduced G* and increased the bread specific volume and cell density, but the breads obtained were paler than the rice flour breads. Comparing the starches, wheat starch breads had better overall acceptability and had a greater volume than maize-starch bread. The highest value for sensorial acceptability corresponded to the bread produced with a mixture of rice flour (59 g/100 g) and wheat starch (41 g/100 g).

  6. Characterization of chestnut (Castanea sativa, mill starch for industrial utilization

    Directory of Open Access Journals (Sweden)

    Demiate Ivo Mottin

    2001-01-01

    Full Text Available Studies were conducted to characterize the chestnut and its starch. Chemical composition of the chestnuts showed high level of starch. Moisture level in the raw nuts was around 50g/100g in wet basis and starch content, around 80g/100g in dry basis; other nut flour components were protein (5.58 g/100g, lipid (5.39 g/100g, crude fiber (2.34 g/100g and ash (2.14 g/100g. Starch fraction was chemically characterized in order to identify the granule quality as compared with those of cassava and corn. This fraction showed more lipids and proteins than the other starches. Chestnut starch granules showed peculiar shape, smaller than the control starches and low amount of damaged units. Chemical composition concerning amylose : amylopectin ratio was intermediate to that presented by cassava and corn starch granules. Water absorption at different temperatures as well as solubility were also intermediate but closer to that presented by cassava granules. The same behavior was observed in the interaction with dimethyl-sulfoxide. Native starch granules and those submitted to enzymatic treatment with commercial alpha-amylase and also with enzymes from germinated wheat were observed by scanning electronic microscopy. Water suspensions of chestnut starch granules were heated to form pastes that were studied comparatively to those obtained with cassava and corn starches. Viscographic pattern of chestnut starch pastes showed a characteristic profile with high initial viscosity but peak absence, high resistance to mechanical stirring under hot conditions and high final viscosity. There was no way to compare it with the paste viscographic profiles obtained with the control starches. Chestnut starch pastes were stable down to pH 4 but unstable at pH 3. The water losses observed in the chestnut starch pastes after freeze-thaw cycles showed more similarity to the pattern observed in corn starch pastes as well as clarity and strength of the gel. In general the results

  7. Computational modeling of biodegradable starch based polymer composites

    Science.gov (United States)

    Joshi, Sachin Sudhakar

    2007-12-01

    Purpose. The goal of this study is to improve the favorable molecular interactions between starch and PPC by addition of grafting monomers MA and ROM as compatibilizers, which would advance the mechanical properties of starch/PPC composites. Methodology. DFT and semi-empirical methods based calculations were performed on three systems: (a) starch/PPC, (b) starch/PPC-MA, and (c) starch-ROM/PPC. Theoretical computations involved the determination of optimal geometries, binding-energies and vibrational frequencies of the blended polymers. Findings. Calculations performed on five starch/PPC composites revealed hydrogen bond formation as the driving force behind stable composite formation, also confirmed by the negative relative energies of the composites indicating the existence of binding forces between the constituent co-polymers. The interaction between starch and PPC is also confirmed by the computed decrease in stretching CO and OH group frequencies participating in hydrogen bond formation, which agree qualitatively with the experimental values. A three-step mechanism of grafting MA on PPC was proposed to improve the compatibility of PPC with starch. Nine types of 'blends' produced by covalent bond formation between starch and MA-grafted PPC were found to be energetically stable, with blends involving MA grafted at the 'B' and 'C' positions of PPC indicating a binding-energy increase of 6.8 and 6.2 kcal/mol, respectively, as compared to the non-grafted starch/PPC composites. A similar increase in binding-energies was also observed for three types of 'composites' formed by hydrogen bond formation between starch and MA-grafted PPC. Next, grafting of ROM on starch and subsequent blend formation with PPC was studied. All four types of blends formed by the reaction of ROM-grafted starch with PPC were found to be more energetically stable as compared to the starch/PPC composite and starch/PPC-MA composites and blends. A blend of PPC and ROM grafted at the '

  8. Improvement of rice starch by gamma irradiation

    International Nuclear Information System (INIS)

    Duan Zhiying; Wu Dianxing; Shen Shengquan; Han Juanying; Xia Yingwu

    2003-01-01

    Three types of rice cultivars, Indica, Japonica and hybrid rice, with similar intermediate apparent amylose content (AAC) as well as early Indica rice cultivars with different amounts of AAC were selected for studying the effects of gamma irradiation on starch viscosity, physico-chemical properties and starch granule structure. Four major parameters of RVA profile, peak viscosity (PKV), hot paste viscosity (HPV), cool paste viscosity (CPV), setback viscosity (SBV) and consistence viscosity (CSV) were considerably decreased with increasing dose levels. Gamma irradiation reduced the amylose contents in the cultivars with low AAC, intermediate AAC, and glutinous rice, but had no effects on the high AAC cultivar. No visible changes in alkali spreading value (ASV) were detected after irradiation, but the peak time (PKT) were reduced with the dose level. Gel consistency (GC) were significantly increased in the tested cultivars, especially in the high AAC Indica rice, suggesting that it is promising to use gamma irradiation to improve eating and cooking quality of rice

  9. Analytical Aspects of Total Starch Polarimetric Determination in Some Cereals

    Directory of Open Access Journals (Sweden)

    Rodica Caprita

    2016-10-01

    Full Text Available Starch is the most important digestible polysaccharide present in foods and feeds. The starch concentration in cereals cannot be determined directly, because the starch is contained within a structurally and chemically complex matrix. Fine grinding and boiling in dilute HCl are preparative steps necessary for complete release of the starch granules from the protein matrix. Starch can be determined using simple and inexpensive physical methods, such as density, refractive index or optical rotation assessment. The polarimetric method allows the determination even of small starch contents due to its extremely high specific rotation. For more accurate results, the contribution of free sugars is eliminated by dissolution in 40% (V/V ethanol. The influence of other optically active substances, which might interfere, is removed by filtration/clarification prior to the optical rotation measurement.

  10. Synthesis of supermacroporous cryogel for bioreactors continuous starch hydrolysis.

    Science.gov (United States)

    Guilherme, Ederson Paulo Xavier; de Oliveira, Jocilane Pereira; de Carvalho, Lorendane Millena; Brandi, Igor Viana; Santos, Sérgio Henrique Sousa; de Carvalho, Gleidson Giordano Pinto; Cota, Junio; Mara Aparecida de Carvalho, Bruna

    2017-11-01

    A bioreactor was built by means of immobilizing alpha-amylase from Aspergillus oryzae by encapsulation, through cryopolymerization of acrylamide monomers for the continuous starch hydrolysis. The starch hydrolysis was evaluated regarding pH, the concentration of immobilized amylase on cryogel, the concentration of starch solution and temperature. The maximum value for starch hydrolysis was achieved at pH 5.0, concentration of immobilized enzyme 111.44 mg amylase /g cryogel , concentration of starch solution 45 g/L and temperature of 35°C. The immobilized enzyme showed a conversion ratio ranging from 68.2 to 97.37%, depending on the pH and temperature employed. Thus, our results suggest that the alpha-amylase from A. oryzae immobilized on cryogel monoliths represents a potential process for industrial production of maltose from starch hydrolysis. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Reduction of acrylamide content in bread crust by starch coating.

    Science.gov (United States)

    Liu, Jie; Liu, Xiaojie; Man, Yong; Liu, Yawei

    2018-01-01

    A technique of starch coating to reduce acrylamide content in bread crust was proposed. Bread was prepared in accordance with a conventional procedure and corn or potato starch coating was brushed on the surface of the fermented dough prior to baking. Corn starch coating caused a decrease in acrylamide of 66.7% and 77.1% for the outer and inner crust, respectively. The decrease caused by the potato starch coating was 68.4% and 77.4%, respectively. Starch coating reduced asparagine content significantly (43.4-82.9%; P coating, which effectively shortened the time span (4-8 min) over which acrylamide could form and accumulate. The present study demonstrates that starch coating could be a simple, effective and practical application for reducing acrylamide levels in bread crust without changing the texture and crust color of bread. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  12. Preparation and Properties of Cassava Starch-based Wood Adhesives

    Directory of Open Access Journals (Sweden)

    Qing Xu

    2016-06-01

    Full Text Available A biodegradable, environmentally friendly starch-based wood adhesive with cassava starch as a raw material and butyl acrylate (BA as a co-monomer was synthesized. Results revealed that this cassava starch-based wood adhesive (SWA was more stable than corn starch-based wood adhesive, and its bonding performance was close to that of commercial PVAc emulsion, even after 90 days of storage. Further analysis found that the improved stability of the adhesive could be attributed to its low minimum film forming temperature (MFFT and glass transition temperature (Tg of cassava starch. Moreover, the amount of total volatile organic compounds (TVOCs emitted by the cassava starch-based wood adhesive were much lower than the Chinese national standard control criteria. Therefore, cassava SWA might be a potential alternative to traditional petrochemical-based wood adhesives.

  13. Rheological properties of concentrated solutions of carboxymethyl starch

    Directory of Open Access Journals (Sweden)

    Stojanović Željko

    2003-01-01

    Full Text Available Carboxymethyl starch was synthesized by the esterification of starch with monochloroacetic acid in ethanol as a reaction medium. Three samples of carboxymethyl starch having different degrees of substitution were prepared. The influence of temperature on the viscosity of concentrated carboxymethyl starch solutions, as well as the dynamic-mechanical properties of the concentrated solutions were investigated. The activation energy of viscous flow was determined and it was found that it decreased with increasing degree of substitution. The results of the dynamic-mechanical measurements showed that solutions of starch and carboxymethyl starches with higher degrees of substitution behave as gels. Values of the storage modulus in the rubbery plateau were used to calculate the molar masses between two points of physical crosslinking, the density of crosslinking and the distance between two points of crosslinking.

  14. Development of highly-transparent protein/starch-based bioplastics.

    Science.gov (United States)

    Gonzalez-Gutierrez, J; Partal, P; Garcia-Morales, M; Gallegos, C

    2010-03-01

    Striving to achieve cost-competitive biomass-derived materials for the plastics industry, the incorporation of starch (corn and potato) to a base formulation of albumen and glycerol was considered. To study the effects of formulation and processing, albumen/starch-based bioplastics containing 0-30 wt.% starch were prepared by thermo-plastic and thermo-mechanical processing. Transmittance measurements, DSC, DMTA and tensile tests were performed on the resulting bioplastics. Optical and tensile properties were strongly affected by starch concentration. However, DMTA at low deformation proved to be insensitive to starch addition. Thermo-mechanical processing led to transparent albumen/starch materials with values of strength at low deformation comparable to commodity plastics. Consequently, albumen biopolymers may become a biodegradable alternative to oil-derived plastics for manufacturing transparent packaging and other plastic stuffs. Copyright (c) 2009 Elsevier Ltd. All rights reserved.

  15. Thiol derivatization of Xanthan gum and its evaluation as a mucoadhesive polymer.

    Science.gov (United States)

    Bhatia, Meenakshi; Ahuja, Munish; Mehta, Heena

    2015-10-20

    Thiol-derivatization of xanthan gum polysaccharide was carried out by esterification with mercaptopropionic acid and thioglycolic acid. Thiol-derivatization was confirmed by Fourier-transformed infra-red spectroscopy. Xanthan-mercaptopropionic acid conjugate and xanthan-thioglycolic acid conjugate were found to possess 432.68mM and 465.02mM of thiol groups as determined by Ellman's method respectively. Comparative evaluation of mucoadhesive property of metronidazole loaded buccal pellets of xanthan and thiolated xanthan gum using chicken buccal pouch membrane revealed higher ex vivo bioadhesion time of thiolated xanthan gum as compared to xanthan gum. Improved mucoadhesive property of thiolated xanthan gum over the xanthan gum can be attributed to the formation of disulfide bond between mucus and thiolated xanthan gum. In vitro release study conducted using phosphate buffer (pH 6.8) revealed a sustained release profile of metronidazole from thiolated xanthan pellets as compared to xanthan pellets. In conclusion, thiolation of xanthan improves its mucoadhesive property and sustained the release of metronidazole over a prolonged period. Copyright © 2015 Elsevier Ltd. All rights reserved.

  16. Chewing Gum: Cognitive Performance, Mood, Well-Being, and Associated Physiology

    Science.gov (United States)

    Allen, Andrew P.; Smith, Andrew P.

    2015-01-01

    Recent evidence has indicated that chewing gum can enhance attention, as well as promoting well-being and work performance. Four studies (two experiments and two intervention studies) examined the robustness of and mechanisms for these effects. Study 1 investigated the acute effect of gum on mood in the absence of task performance. Study 2 examined the effect of rate and force of chewing on mood and attention performance. Study 3 assessed the effects of chewing gum during one working day on well-being and performance, as well as postwork mood and cognitive performance. In Study 4, performance and well-being were reported throughout the workday and at the end of the day, and heart rate and cortisol were measured. Under experimental conditions, gum was associated with higher alertness regardless of whether performance tasks were completed and altered sustained attention. Rate of chewing and subjective force of chewing did not alter mood but had some limited effects on attention. Chewing gum during the workday was associated with higher productivity and fewer cognitive problems, raised cortisol levels in the morning, and did not affect heart rate. The results emphasise that chewing gum can attenuate reductions in alertness, suggesting that chewing gum enhances worker performance. PMID:26075253

  17. Gum cordia as carrier of antioxidants: effects on lipid oxidation of peanuts.

    Science.gov (United States)

    Haq, Muhammad Abdul; Azam, Mahmood; Hasnain, Abid

    2015-04-01

    Performance of antioxidants is improved by incorporating them into polymer matrix such as polysaccharides based edible coatings. Gum cordia, an anionic polysaccharide extracted from the fruits of Cordia.myxa could be used as carrier of antioxidants by virtue of its strong adhering and emulsifying properties. This study aimed to explore the potential of gum cordia as carrier of antioxidants when applied as edible coating on peanuts. Gum Cordia was compared with carboxymethyl cellulose (CMC) in delivering of antioxidants: butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT) and ascorbic acid (AA). Coated and uncoated peanuts were stored at 35 °C for 126 days and coating carrier effectiveness was measured by following lipid oxidation using chemical parameters (peroxide value and thiobarbituric acid reactive species) and sensory evaluation (oxidized flavor). Significant differences (p cordia was found better than CMC to deliver the antioxidants. Gum cordia based coating in combination with BHA/BHT exhibited highest protection (290 % higher shelf life than control) based on peroxide value (40 meq.O2 kg(-1)) followed by gum codia plus BHT (244 %), gum cordia plus BHA (232 %), CMC plus BHA/BHT (184 %), CMC plus BHA (139 %), CMC plus BHT (119 %), gum cordia plus AA (96 %) and CMC plus AA (46 %).

  18. Guar gum effects on food intake, blood serum lipids and glucose levels of Wistar rats.

    Science.gov (United States)

    Frias, A C; Sgarbieri, V C

    1998-01-01

    The effects of guar gum derived from the endosperm of Cyamopsis tetragonoloba (75% soluble fiber, 7.6% insoluble fiber, 2.16% crude protein, 0.78% total lipids, 0.54% ash and 9.55% moisture) on food intake, levels of blood serum cholesterol, triacylglycerols, glucose and LDL and HDL-cholesterol were studied. The effects of guar gum on indices of protein absorption and utilization were also investigated. Diets containing 0%, 10% and 20% (w/w) guar gum or 10% and 20% cellulose powder (reference) were fed to normal rats for 60 days. The rats fed the guar gum diets showed significantly (p Guar gum decreased blood serum glucose only during the first month of the experiment, and no changes in the indices of protein absorption and utilization were found. The guar gum caused a 10% increase in the small intestine length and a 25% retardation in the intestinal transit. The results of this research suggested that guar gum could potentially be effective in the treatment of hypercholesterolemia and obesity in humans.

  19. Effect of Guar Gum with Sorbitol Coating on the Properties and Oil Absorption of French Fries.

    Science.gov (United States)

    Jia, Bo; Fan, Daming; Li, Jinwei; Duan, Zhenhua; Fan, Liuping

    2017-12-13

    This paper investigated the effects of guar gum with sorbitol coating on the oil absorption of French fries by combined dye oil methods, confocal laser scanning microscopy (CLSM) and scanning electron microscopy (SEM). The results showed that pretreatment of blanching with calcium ions and coating with guar gum and sorbitol could significantly reduce the structural oil (STO) and penetrated surface oil (PSO) of French fries and have no negative effects on its texture and also effectively control the final moisture content ( p French fries with guar gum and sorbitol reduced by 50.8%, 33.1% and 30.6%, respectively. CLSM photographs confirmed that STO significantly reduced after coating with guar gum and sorbitol, followed by PSO. In the process of frying, the coatings of guar gum or guar gum with sorbitol could effectively prevent oil from infiltrating the potato tissue, which can be seen in the SEM photographs. The barrier properties of French fries were enhanced by coating guar gum, and sorbitol was added to avoid pores and cracks. Blanching with calcium ion can significantly reduce the final moisture content of coating French fries.

  20. Chewing gum benefits sustained attention in the absence of task degradation.

    Science.gov (United States)

    Johnson, Andrew J; Muneem, Mohammed; Miles, Christopher

    2013-07-01

    The present study examined the effect of chewing gum on sustained attention and associated changes in subjective alertness. In a within-participants design, 20 participants completed an extended version of the sustained attention response task (SART: Robertson et al., 1997), both with and without chewing gum. Self-rated measures of alertness, contentedness, and calmness were taken before and after the SART. Chewing gum was associated with improved attentional task performance. This finding was not contingent upon a general decrease in attentional performance and was apparent at all stages of the task. Subjective measures of alertness, contentedness, and calmness were higher following the chewing of gum. Changes in sustained attention co-varied with subjective alertness. The effects of chewing gum on attention and alertness are consistent with past literature and were not contingent on declines in attention. Additionally, we found evidence that gum-induced changes in self-rated alertness and attention are related. We found no support for the proposition that chewing gum can impair attention due to the division of resources.

  1. Chewing Gum: Cognitive Performance, Mood, Well-Being, and Associated Physiology

    Directory of Open Access Journals (Sweden)

    Andrew P. Allen

    2015-01-01

    Full Text Available Recent evidence has indicated that chewing gum can enhance attention, as well as promoting well-being and work performance. Four studies (two experiments and two intervention studies examined the robustness of and mechanisms for these effects. Study 1 investigated the acute effect of gum on mood in the absence of task performance. Study 2 examined the effect of rate and force of chewing on mood and attention performance. Study 3 assessed the effects of chewing gum during one working day on well-being and performance, as well as postwork mood and cognitive performance. In Study 4, performance and well-being were reported throughout the workday and at the end of the day, and heart rate and cortisol were measured. Under experimental conditions, gum was associated with higher alertness regardless of whether performance tasks were completed and altered sustained attention. Rate of chewing and subjective force of chewing did not alter mood but had some limited effects on attention. Chewing gum during the workday was associated with higher productivity and fewer cognitive problems, raised cortisol levels in the morning, and did not affect heart rate. The results emphasise that chewing gum can attenuate reductions in alertness, suggesting that chewing gum enhances worker performance.

  2. Chewing gum: cognitive performance, mood, well-being, and associated physiology.

    Science.gov (United States)

    Allen, Andrew P; Smith, Andrew P

    2015-01-01

    Recent evidence has indicated that chewing gum can enhance attention, as well as promoting well-being and work performance. Four studies (two experiments and two intervention studies) examined the robustness of and mechanisms for these effects. Study 1 investigated the acute effect of gum on mood in the absence of task performance. Study 2 examined the effect of rate and force of chewing on mood and attention performance. Study 3 assessed the effects of chewing gum during one working day on well-being and performance, as well as postwork mood and cognitive performance. In Study 4, performance and well-being were reported throughout the workday and at the end of the day, and heart rate and cortisol were measured. Under experimental conditions, gum was associated with higher alertness regardless of whether performance tasks were completed and altered sustained attention. Rate of chewing and subjective force of chewing did not alter mood but had some limited effects on attention. Chewing gum during the workday was associated with higher productivity and fewer cognitive problems, raised cortisol levels in the morning, and did not affect heart rate. The results emphasise that chewing gum can attenuate reductions in alertness, suggesting that chewing gum enhances worker performance.

  3. Detrimental effects of gum chewing on vigilance in children with attention deficit hyperactivity disorder.

    Science.gov (United States)

    Tucha, Lara; Simpson, William; Evans, Lynsay; Birrel, Laura; Sontag, Thomas A; Lange, Klaus W; Tucha, Oliver

    2010-12-01

    Impairments of attention are cardinal features of attention deficit hyperactivity disorder (ADHD) and can seriously affect the daily life of children with ADHD. Despite effective treatment strategies, there is a need of further treatment options that can be added to available and well established treatments. Further treatment options are needed since available treatments are often time consuming, expensive and limited regarding their external validity. Recent research demonstrated that gum chewing has beneficial effects on cognition including certain aspects of attention. Therefore, gum chewing may benefit children with ADHD in situations requiring particular cognitive efforts. In a crossover study, attentional functioning of 32 children with ADHD and 32 children without the condition was examined. All participants were assessed with chewing gum and without chewing gum. A computerized test was used for the assessment of vigilance and sustained attention. The findings of the present study suggest that gum chewing during task execution has detrimental effects on vigilance of both healthy children and children with ADHD. Sustained attention was not affected by gum chewing. Chewing gum, therefore, appears not to improve attentional performance in children with ADHD. Copyright © 2010 Elsevier Ltd. All rights reserved.

  4. Development of nanocomposites based on potato starch

    International Nuclear Information System (INIS)

    Brito, Luciana Macedo; Tavares, Maria Ines Bruno

    2013-01-01

    Nanocomposites of potato starch were prepared by the solution intercalation method with the addition of organically modified montmorillonite clay (Viscogel B and unmodified sodic clay (NT25) as well as modified and unmodified silica (R972 and A200, respectively), using water as the solvent. The nanocomposites were characterized by conventional techniques of X-ray diffraction and thermogravimetric analysis. They were also characterized using the non-conventional low-field nuclear magnetic resonance, which is an effective alternative technique for characterizing nanocomposites. This technique allows one to investigate dispersion of nanofillers by the degree of intercalation and/or exfoliation, in addition to determine the distribution of nanoparticles in the polymer matrix and modifications of the molecular mobility of these fillers. The nanostructured materials obtained with the clays presented good dispersion and formation of mixed nanomaterials, with different degrees of intercalation and exfoliation. The mobility of the material decreased upon adding silica in the starch matrix, which applied to both types of silica. From the TGA technique, a slight increase in thermal stability of the nanocomposite was noted in relation to the starch matrix. (author)

  5. Enzymatic transformation of nonfood biomass to starch

    Science.gov (United States)

    You, Chun; Chen, Hongge; Myung, Suwan; Sathitsuksanoh, Noppadon; Ma, Hui; Zhang, Xiao-Zhou; Li, Jianyong; Zhang, Y.-H. Percival

    2013-01-01

    The global demand for food could double in another 40 y owing to growth in the population and food consumption per capita. To meet the world’s future food and sustainability needs for biofuels and renewable materials, the production of starch-rich cereals and cellulose-rich bioenergy plants must grow substantially while minimizing agriculture’s environmental footprint and conserving biodiversity. Here we demonstrate one-pot enzymatic conversion of pretreated biomass to starch through a nonnatural synthetic enzymatic pathway composed of endoglucanase, cellobiohydrolyase, cellobiose phosphorylase, and alpha-glucan phosphorylase originating from bacterial, fungal, and plant sources. A special polypeptide cap in potato alpha-glucan phosphorylase was essential to push a partially hydrolyzed intermediate of cellulose forward to the synthesis of amylose. Up to 30% of the anhydroglucose units in cellulose were converted to starch; the remaining cellulose was hydrolyzed to glucose suitable for ethanol production by yeast in the same bioreactor. Next-generation biorefineries based on simultaneous enzymatic biotransformation and microbial fermentation could address the food, biofuels, and environment trilemma. PMID:23589840

  6. Transfer action of cyclodextrin glycosyltransferase on starch

    Energy Technology Data Exchange (ETDEWEB)

    Kitahata, S; Okada, S [Osaka City Technical Research Inst. (Japan)

    1975-11-01

    The transglycosylation reaction of the cyclodextrin glycosyltransferase from Bacillus megaterium (No. 5 enzyme) and Bacillus macerans (BMA) were examined. No.5 enzyme was more efficient in transglycosylation reaction than BMA in the every acceptor employed in the present study. The order of the efficient acceptors for No. 5 enzyme was maltose (G2), glucose (G1), maltotriose (G3) and sucrose (GF). On the other hand, that found for BMA was G1, G2, GF and G3. The transglycosylation products to glucose formed by the action of No. 5 enzyme on starch were G2, G3, maltotetraose (G4), maltopentaose (G5), maltohexaose (G6) and maltoheptaose (G7) in the order of their quantities, while, in the case of BMA, they were G2, G3, G5, G7 = G4 and G6. The larger transglycosylation products to sucrose formed by the action of No. 5 enzyme on starch were maltosylfructose. On the other hand, that formed by the action of BMA was maltoheptaosylfructose. It was suggested that cyclodextrin glycosyltransferase could transfer the glucosyl residues to an acceptor directly from starch, as well as through cyclodextrin.

  7. Compatibility of chewing gum excipients with the amino acid L-cysteine and stability of the active substance in directly compressed chewing gum formulation.

    Science.gov (United States)

    Kartal, Alma; Björkqvist, Mikko; Lehto, Vesa-Pekka; Juppo, Anne Mari; Marvola, Martti; Sivén, Mia

    2008-09-01

    Using L-cysteine chewing gum to eliminate carcinogenic acetaldehyde in the mouth during smoking has recently been introduced. Besides its efficacy, optimal properties of the gum include stability of the formulation. However, only a limited number of studies exist on the compatibility of chewing gum excipients and stability of gum formulations. In this study we used the solid-state stability method, Fourier transform infrared spectroscopy and isothermal microcalorimetry to investigate the interactions between L-cysteine (as a free base or as a salt) and excipients commonly used in gum. These excipients include xylitol, sorbitol, magnesium stearate, Pharmagum S, Every T Toco and Smily 2 Toco. The influence of temperature and relative humidity during a three-month storage period on gum formulation was also studied. Cysteine alone was stable at 25 degrees C/60% RH and 45 degrees C/75% RH whether stored in open or closed glass ambers. As a component of binary mixtures, cysteine base remained stable at lower temperature and humidity but the salt form was incompatible with all the studied excipients. The results obtained with the different methods corresponded with each other. At high temperature and humidity, excipient incompatibility with both forms of cysteine was obvious. Such sensitivity to heat and humidity during storage was also seen in studies on gum formulations. It was also found that cysteine is sensitive to high pressure and increase in temperature induced by compression. The results suggest that the final product should be well protected from temperature and humidity and, for example, cooling process before compression should be considered.

  8. Remineralization of enamel subsurface lesions by chewing gum with added calcium.

    Science.gov (United States)

    Cai, Fan; Shen, Peiyan; Walker, Glenn D; Reynolds, Coralie; Yuan, Yi; Reynolds, Eric C

    2009-10-01

    Chewing sugar-free gum has been shown to promote enamel remineralization. Manufacturers are now adding calcium to the gum in an approach to further promote enamel remineralization. The aim of this study was to compare the remineralization efficacy of four sugar-free chewing gums, two containing added calcium, utilizing a double-blind, randomized, crossover in situ model. The sugar-free gums were: Trident Xtra Care, Orbit Professional, Orbit and Extra. Ten subjects wore removable palatal appliances with four human-enamel half-slab insets containing subsurface demineralized lesions. For four times a day for 14 consecutive days subjects chewed one of the chewing gums for 20min. After each treatment the enamel slabs were removed, paired with their respective demineralized control slabs, embedded, sectioned and mineral level determined by microradiography. After 1-week rest the subjects chewed another of the four gums and this was repeated until each subject had used the four gum products. Chewing with Trident Xtra Care resulted in significantly higher remineralization (20.67+/-1.05%) than chewing with Orbit Professional (12.43+/-0.64%), Orbit (9.27+/-0.59%) or Extra (9.32+/-0.35%). The form of added calcium in Trident Xtra Care was CPP-ACP and that in Orbit Professional calcium carbonate with added citric acid/citrate for increased calcium solubility. Although saliva analysis confirmed release of the citrate and calcium from the Orbit Professional gum the released calcium did not result in increased enamel remineralization over the normal sugar-free gums. These results highlight the importance of calcium ion bioavailability in the remineralization of enamel subsurface lesions in situ.

  9. Effects of chewing gum on cognitive function, mood and physiology in stressed and non-stressed volunteers.

    Science.gov (United States)

    Smith, Andrew

    2010-02-01

    Recent research suggests that chewing gum may improve aspects of cognitive function and mood. There is also evidence suggesting that chewing gum reduces stress. It is important, therefore, to examine these two areas and to determine whether contextual factors (chewing habit, type of gum, and personality) modify such effects. The aims of the present study were: (i) to determine whether chewing gum improved mood and mental performance; (ii) to determine whether chewing gum had benefits in stressed individuals; and (iii) to determine whether chewing habit, type of gum and level of anxiety modified the effects of gum. A cross-over study involving 133 volunteers was carried out. Each volunteer carried out a test session when they were chewing gum and without gum, with order of gum conditions counterbalanced across subjects. Baseline sessions were conducted prior to each test session. Approximately half of the volunteers were tested in 75 dBA noise (the stress condition) and the rest in quiet. Volunteers were stratified on chewing habit and anxiety level. Approximately, half of the volunteers were given mint gum and half fruit gum. The volunteers rated their mood at the start and end of each session and had their heart rate monitored over the session. Saliva samples were taken to allow cortisol levels (good indicator of alertness and stress) to be assayed. During the session, volunteers carried out tasks measuring a range of cognitive functions (aspects of memory, selective and sustained attention, psychomotor speed and accuracy). Chewing gum was associated with greater alertness and a more positive mood. Reaction times were quicker in the gum condition, and this effect became bigger as the task became more difficult. Chewing gum also improved selective and sustained attention. Heart rate and cortisol levels were higher when chewing which confirms the alerting effect of chewing gum. Overall, the results suggest that chewing gum produces a number of benefits that are

  10. Effect of Drying Method and Variety on Quality of Cassava Starch ...

    African Journals Online (AJOL)

    Effect of Drying Method and Variety on Quality of Cassava Starch Extracts. ... Cassava starch is one of the main industrial products of cassava processing. ... Also, cassava starch samples dried at lower temperature have better functional and ...

  11. Effects of citric acid esterification on digestibility, structural and physicochemical properties of cassava starch.

    Science.gov (United States)

    Mei, Ji-Qiang; Zhou, Da-Nian; Jin, Zheng-Yu; Xu, Xue-Ming; Chen, Han-Qing

    2015-11-15

    In this study, citric acid was used to react with cassava starch in order to compare the digestibility, structural and physicochemical properties of citrate starch samples. The results indicated that citric acid esterification treatment significantly increased the content of resistant starch (RS) in starch samples. The swelling power and solubility of citrate starch samples were lower than those of native starch. Compared with native starch, a new peak at 1724 cm(-1) was appeared in all citrate starch samples, and crystalline peaks of all starch citrates became much smaller or even disappeared. Differential scanning calorimetry results indicated that the endothermic peak of citrate starches gradually shrank or even disappeared. Moreover, the citrate starch gels exhibited better freeze-thaw stability. These results suggested that citric acid esterification induced structural changes in cassava starch significantly affected its digestibility and it could be a potential method for the preparation of RS with thermal stability. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. 40 CFR 427.30 - Applicability; description of the asbestos paper (starch binder) subcategory.

    Science.gov (United States)

    2010-07-01

    ... asbestos paper (starch binder) subcategory. 427.30 Section 427.30 Protection of Environment ENVIRONMENTAL... Asbestos Paper (Starch Binder) Subcategory § 427.30 Applicability; description of the asbestos paper... asbestos paper (starch binder). ...

  13. Effect of ionizing radiation on starch and cellulose

    International Nuclear Information System (INIS)

    Klenha, J.; Bockova, J.

    1973-09-01

    The investigation is reported of the effects of ionizing radiation both on macromolecular systems generally and on polysaccharides, starch and cellulose. Attention is focused on changes in the physical and physico-chemical properties of starch and cellulose, such as starch swelling, gelation, viscosity, solubility, reaction with iodine, UV, IR and ESR spectra, chemical changes resulting from radiolysis and from the effect of amylases on irradiated starch, changes in cellulose fibre strength, water absorption, stain affinity, and also the degradation of cellulose by radiation and the effect of cellulases on irradiated cellulose. Practical applications of the findings concerning cellulose degradation are discussed. (author)

  14. Starch bioengineering in Brachypodium distachyon

    DEFF Research Database (Denmark)

    Tanackovic, Vanja; Svensson, Jan Tommy; Buleon, A

    2011-01-01

    Brachypodium distachyon was recently introduced as a model plant for temperate cereals (Opanowicz et al., 2008). We aim to establish Brachypodium as a model for cereal starch metabolism. Grain starch from two lines: Bd21 and Bd21-3 are being characterized. Microscopic, chemical and structural data...... including amylopectin chain length distribution, phosphate content and amylose content provided further evidence for the close relationship to temperate cereals even though starch content and starch granule size were considerably lower than that for barley (Hordeum vulgare). Bioinformatics analyses...... in temperate cereals....

  15. Supply of avocado starch (Persea americana mill) as bioplastic material

    Science.gov (United States)

    Ginting, M. H. S.; Hasibuan, R.; Lubis, M.; Alanjani, F.; Winoto, F. A.; Siregar, R. C.

    2018-02-01

    The purpose of this study was to determine the effect of time precipitation of avocado slurry seed to yield of starch. Starch analysis included starch content, moisture content, amylose content, amylopectin content, ash content, protein content, fat content, Fourier transform infra red analysis and rapid visco analyzer. Supply of starch from avocado seeds was used by extraction method. Every one hundred grams of avocado slurry was precipitated by gravity with variations for 4 hours, 8 hours, 12 hours, 16 hours, 20 hours and 24 hours. The Starch yield was washed, and dried using oven at 70°C for 30 minutes. Starch yield was the highest as 24.20 gram at 24 hours. The result of starch characterization was 73.62%, water content 16.6%, amylose 0.07%, amylopectin 73.55%, ash content 0.23%, protein content 2.16%, fat content 1.09%. Rapid visco analyzer obtained at 91.33°C of gelatinization temperature. Scanning electron microscopy analyzes obtained 20 μm oval-shaped starch granules. Fourier Transform Infra Red analysis of starch obtained the peak spectrum of O-H group of alcohols, C-H alkanes and C-O ether.

  16. Size Controlled Synthesis of Starch Nanoparticles by a Microemulsion Method

    Directory of Open Access Journals (Sweden)

    Suk Fun Chin

    2014-01-01

    Full Text Available Controllable particles sizes of starch nanoparticles were synthesized via a precipitation in water-in-oil microemulsion approach. Microemulsion method offers the advantages of ultralow interfacial tension, large interfacial area, and being thermodynamically stable and affords monodispersed nanoparticles. The synthesis parameters such as stirring rates, ratios of oil/cosurfactant, oil phases, cosurfactants, and ratios of water/oil were found to affect the mean particle size of starch nanoparticles. Starch nanoparticles with mean particles sizes of 109 nm were synthesized by direct nanoprecipitation method, whereas by using precipitation in microemulsion approach, starch nanoparticles with smaller mean particles sizes of 83 nm were obtained.

  17. Optimization of enzymatic hydrolysis of guar gum using response surface methodology

    OpenAIRE

    Mudgil, Deepak; Barak, Sheweta; Khatkar, B. S.

    2012-01-01

    Guar gum is a polysaccharide obtained from guar seed endosperm portion. Enzymatically hydrolyzed guar gum is low in viscosity and has several health benefits as dietary fiber. In this study, response surface methodology was used to determine the optimum conditions for hydrolysis that give minimum viscosity of guar gum. Central composite was employed to investigate the effects of pH (3–7), temperature (20–60 °C), reaction time (1–5 h) and cellulase concentration (0.25–1.25 mg/g) on viscosity d...

  18. Chewing gum does not induce context-dependent memory when flavor is held constant.

    Science.gov (United States)

    Overman, Amy A; Sun, Justin; Golding, Abbe C; Prevost, Darius

    2009-10-01

    This study examined the effect of chewing gum on memory when flavor is held constant. Four separate groups of participants (total n=101) completed a word recall task. At learning and recall, participants either chewed a piece of gum or sucked a sweet. Each participant completed the memory task twice, once with abstract words and once with concrete words. A significant effect of word type (concrete vs. abstract) was found, however recall performance was not improved by matched oral activity at learning and recall. The results cast further doubt on the ability of chewing gum to induce context-dependent memory effects.

  19. Effect of chewing gums containing the probiotic bacterium Lactobacillus reuteri on oral malodour

    DEFF Research Database (Denmark)

    Keller, Mette K; Bardow, Allan; Jensdottir, Thorbjörg

    2012-01-01

    OBJECTIVE: To evaluate the effect of chewing gums containing probiotic bacteria on oral malodour. The null hypothesis was that no difference would be displayed compared with placebo gums. MATERIALS AND METHODS: Twenty-five healthy young adults with self-reported malodorous morning breath completed...... this randomized double-blind placebo-controlled cross-over trial. The design included run-in and wash-out periods interspersed by two intervention periods of 14 days each. The subjects were instructed to chew one gum in the morning and one in the evening containing either two strains of probiotic lactobacilli (L...... lower in the probiotic group compared with the placebo group (p chewing...

  20. Relative bioavailability of methadone hydrochloride administered in chewing gum and tablets

    DEFF Research Database (Denmark)

    Christrup, Lona Louring; Angelo, H.R.; Bonde, J.

    1990-01-01

    Methadone administered in chewing gum in doses of 16.7-22.6 mg to seven patients in a study using an open balanced cross-over design, was compared with 20 mg of methadone given perorally as tablets. There was no significant difference in the AUC/D obtained after administration of chewing gum...... and tablets (p>0.05). It is concluded that the chewing gum formulation should be considered for further testing with respect to suppression of abstinence syndrome in narcotic addicts....

  1. Trace element evaluation of different varieties of chewing gum by radiochemical neutron activation analysis

    International Nuclear Information System (INIS)

    Zaidi, J.H.; Arif, M.; Fatima, I.; Ahmad, S.; Qureshi, I.H.

    2000-01-01

    Extensive use of chewing gums, by children in particular, entails the evaluation of trace element contents in them. Radiochemical neutron activation analysis (RNAA) was successfully employed to determine the concentration of 35 trace elements (essential, toxic and nonessential) in eight different brands of chewing gum generally consumed in Rawalpindi/Islamabad area. Comparison of trace element data of our work with literature has been presented. None of the elements detected in the brands of chewing gum examined was found to be present at a level representing a substantial contribution to the total dietary intake of the element. (author)

  2. Relative bioavailability of methadone hydrochloride administered in chewing gum and tablets.

    Science.gov (United States)

    Christrup, L L; Angelo, H R; Bonde, J; Kristensen, F; Rasmussen, S N

    1990-01-01

    Methadone administered in chewing gum in doses of 16.7-22.6 mg to seven patients in a study using an open balanced cross-over design, was compared with 20 mg of methadone given perorally as tablets. There was no significant difference in the AUC/D obtained after administration of chewing gum and tablets (p greater than 0.05). It is concluded that the chewing gum formulation should be considered for further testing with respect to suppression of abstinence syndrome in narcotic addicts.

  3. Natural gums of plant origin as edible coatings for food industry applications.

    Science.gov (United States)

    Saha, Anuradha; Tyagi, Shvetambri; Gupta, Rajinder K; Tyagi, Yogesh K

    2017-12-01

    Natural plant-based gums and their derivatives are widely utilized in food industries, however, their applications as edible coatings to extend fresh fruits and vegetable shelf-life has been explored recently. These natural polymeric polysaccharides have many advantages as compared to synthetic polymers, because they are biodegradable, nontoxic, economical and easily available in the environment. Natural gums can also be semi synthetically modified to produce derivatives, which can easily compete with the synthetic preservatives available on the food market. In this review, the recent developments in the use of natural gums and their derivatives as edible coatings have been explored and discussed.

  4. The amino acid composition of the proteinaceous component of gum tragacanth (Asiatic Astragalus spp.).

    Science.gov (United States)

    Anderson, D M; Howlett, J F; McNab, C G

    1985-01-01

    Six Iranian and seven Turkish samples of commercial gum tragacanth, and a sample of Turkish 'gum traganton', have been studied. Their nitrogen content varied from 0.17 to 0.58%. Their amino acid compositions are characterized by the presence of very large but variable proportions of hydroxyproline and substantial proportions of serine, proline and valine. The data presented may be useful for extending the current specifications for identity and purity, at present based solely on polysaccharide parameters, for gum tragacanth (E413).

  5. Composite wheat-plantain starch salted noodles: Preparation, proximal composition and in vitro starch digestibility

    OpenAIRE

    Rendón-Villalobos, Rodolfo; Osorio-Díaz, Perla; Agama-Acevedo, Edith; Tovar, Juscelino; Bello-Pérez, Luis A

    2008-01-01

    Salted noodles were prepared with different contents of wheat grits and plantain starch (PS). The blends were hydrated with 2% NaCl (w/v), homogenized, and the resulting doughs were sheeted through a pasta machine, cut into strips ~30cm in length, cooked, and their composition and in vitro starch digestibility was assessed. Moisture (6.43-7.60%) and ash contents (2.08-3.12%) increased by the addition of PS. Fat level decreased from 0.41 to 0.31% as the substitution of wheat grits increased. R...

  6. Novel polymer blends with thermoplastic starch

    Science.gov (United States)

    Taghizadeh, Ata

    A new class of polymers known as "bioplastics" has emerged and is expanding rapidly. This class consists of polymers that are either bio-based or biodegradable, or both. Among these, polysaccharides, namely starch, are of great interest for several reasons. By gelatinizing starch via plasticizers, it can be processed in the same way as thermoplastic polymers with conventional processing equipment. Hence, these bio-based and biodegradable plastics, with their low source and refinery costs, as well as relatively easy processability, have made them ideal candidates for incorporation into various current plastic products. Four different plasticizers have been chosen here for gelatinization of thermoplastic starch (TPS): glycerol, sorbitol, diglycerol and polyglycerol, with the latter two being used for the first time in such a process. Two methodological categories are used. The first involves a calorimetric method (Differential Scanning Calorimetry) as well as optical microscopy; these are "static" methods where no shear is applied A wide range of starch/water/plasticizer compositions were prepared to explore the gelatinization regime for each plasticizer. The onset and conclusion gelatinization temperatures for sorbitol and glycerol were found to be in the same vicinity, while diglycerol and polyglycerol showed significantly higher transition temperatures. The higher molecular weight and viscosity of polyglycerol allow this transition to occur at an even higher temperature than with diglycerol. This is due to the increase in molecular weight and viscosity of the two new plasticizers, as well as their significant decrease in water solubility. It is demonstrated that the water/plasticizer ratio has a pronounced effect on gelatinization temperatures. When plasticizer content was held constant and water content was increased, it was found that the gelatinization temperature decreased for all the plasticizers. Meanwhile, when the water content was held constant and the

  7. 13CO2 breath test to measure the hydrolysis of various starch formulations in healthy subjects.

    OpenAIRE

    Hiele, M; Ghoos, Y; Rutgeerts, P; Vantrappen, G; de Buyser, K

    1990-01-01

    13CO2 starch breath test was used to study the effect of physicochemical characteristics of starch digestion. As starch is hydrolysed to glucose, which is subsequently oxidised to CO2, differences in 13CO2 excretion after ingestion of different starch products must be caused by differences in hydrolysis rate. To study the effect of the degree of chain branching, waxy starch, containing 98% amylopectin, was compared with high amylose starch, containing 30% amylopectin, and normal crystalline s...

  8. Preparation and characterization of a chemically sulfated cashew gum polysaccharide

    Energy Technology Data Exchange (ETDEWEB)

    Moura Neto, Erico de; Maciel, Jeanny da S.; Cunha, Pablyana L. R.; Paula, Regina Celia M. de; Feitosa, Judith P.A., E-mail: judith@dqoi.ufc.br [Departamento de Quimica Organica e Inorganica, Universidade Federal do Ceara, Fortaleza (Brazil)

    2011-09-15

    Cashew gum (CG) was sulfated in pyridine:formamide using chlorosulfonic acid as the reagent. Confirmation of sulfation was obtained by Fourier transform infrared (FTIR) spectroscopy through the presence of an asymmetrical S=O stretching vibration at 1259 cm{sup -1}. The degrees of substitution were 0.02, 0.24 and 0.88 determined from the sulfur percentage. 1D and 2D nuclear magnetic resonance (NMR) data showed that the sulfation occurred at primary carbons. An increase of at least 4% of the solution viscosity was observed due to sulfation. The thermal gravimetric curves (TGA) indicate that the derivatives are stable up to ca. 200 deg C. The sulfated CG is compared to carboxymethylated CG in order to verify the possibility of the use of the former in the preparation of polyelectrolyte complexes; the latter is already being used for this application. (author)

  9. Surface Modification of Magnetic Nanoparticles Using Gum Arabic

    International Nuclear Information System (INIS)

    Williams, Darryl N.; Gold, Katie A.; Holoman, Tracey R. Pulliam; Ehrman, Sheryl H.; Wilson, Otto C.

    2006-01-01

    Magnetite nanoparticles were synthesized and functionalized by coating the particle surfaces with gum arabic (GA) to improve particle stability in aqueous suspensions (i.e. biological media). Particle characterization was performed using transmission electron microscopy (TEM) and dynamic light scattering (DLS) to analyze the morphology and quantify the size distribution of the nanoparticles, respectively. The results from DLS indicated that the GA-treated nanoparticles formed smaller agglomerates as compared to the untreated samples over a 30-h time frame. Thermogravimetric analyses indicated an average weight loss of 23%, showing that GA has a strong affinity toward the iron oxide surface. GA most likely contributes to colloid stability via steric stabilization. It was determined that the adsorption of GA onto magnetite exhibits Langmuir behavior

  10. The cereal starch endosperm development and its relationship with other endosperm tissues and embryo.

    Science.gov (United States)

    Zheng, Yankun; Wang, Zhong

    2015-01-01

    The cereal starch endosperm is the central part of endosperm, and it is rich in starch and protein which are the important resources for human food. The starch and protein are separately accumulated in starch granules and protein bodies. Content and configuration of starch granules and protein bodies affect the quality of the starch endosperm. The development of starch endosperm is mediated by genes, enzymes, and hormones, and it also has a close relationship with other endosperm tissues and embryo. This paper reviews the latest investigations on the starch endosperm and will provide some useful information for the future researches on the development of cereal endosperm.

  11. Development of postcompressional textural tests to evaluate the mechanical properties of medicated chewing gum tablets with high drug loadings.

    Science.gov (United States)

    Al Hagbani, Turki; Nazzal, Sami

    2018-02-01

    Medicated chewing gum tablets (CGTs) represent a unique platform for drug delivery. Loading directly compressible gums with high concentrations of powdered medication, however, results in compacts with hybrid properties between a chewable gum and a brittle tablet. The aim of the present study was to develop textural tests that can identify the point at which CGTs begin to behave like a solid tablet upon drug incorporation. Curcumin (CUR) CGTs made with Health in gum were prepared with increasing CUR load from 0 to 100% and were characterized for their mechanical properties by a single-bite (knife) and a two-bite tests. From each test several parameters were extracted and correlated with drug loading. In the single-bite test, the change in the resistance of the compacts to plastic deformation was found to give a definitive guide on whether they behave as gums or tablets. A more in depth analysis of the impact of CUR loading on the chewability of the CGTs was provided by the two-bite test where CUR loading was found to have a nonlinear impact on the mechanical properties of compacts. An upper limit of 10% was found to yield compacts with gum-like properties, which were abolished at higher CUR loads. The textural test procedure outlined in this study are expected to assist those involved in the formulation of medicated gums for pharmaceutical applications in making an informed decision on the impact of drug loading on gum behavior before proceeding with clinical testing. There is a growing interest in utilizing medicated chewing gums for drug delivery, especially those made using directly compressible gum bases, such as Health in gum. Directly compressing a gum base with high amounts of solid drug powder, however, poses a challenge as it may result in compressed compacts with hybrid properties between a chewing gum and a hard tablet. Currently, official Pharmacopeias do not specify a testing procedure for the estimation of the mechanical and textural properties of

  12. VAPOR MIXER FOR GELATINIZATION OF STARCH IN LIQUEFYING STATION

    Directory of Open Access Journals (Sweden)

    V. V. Ananskikh

    2015-01-01

    Full Text Available Starch hydrolysis is main technological process in production of starch sweeteners. Acid hydrolysis of starch using hydrochloric acid is carried out very fast but it does not allow to carry out full hydrolysis and to produce products with given carbohydrate composition. Bioconversion of starch allows to eliminate these limitations. At production of starch sweeteners from starch using enzymes starch hydrolysis is carried out in two stages At first starchstarch liquefaction the rapid increase of viscosity takes place which requires intensive mixing. Liquefying station consists of jet-cooker, holder, pressure regulator and evaporator. Jet-cooker of starch is its main part, starch is quickly turns into soluble (gelatinized state and it is partially liquefied by injection of starch suspension by flow of water vapor under pressure not less than 0,8 MPa. Heat and hydraulic calculation were carried out in order to determine constructive sizes of mixer for cooking of starch. The main hydraulic definable parameters are pressure drop in mixer, vapor pressure at mixer inlet, daily capacity of station by glucose syrup M, product consumption (starch suspension, diameter of inlet section of vapor nozzle. The goal of calculation was to determine vapor consumption M1, diameter d2 of outlet section of confuser injector, length l2 of gelatinization section. For heat calculation there was used Shukhov’s formula along with heat balance equation for gelatinization process. The numerical solution obtained with adopted assumptions given in applied mathematical package MATHCAD, for M = 50 t/day gives required daily vapor consumption M1 = 14,446 т. At hydraulic calculation of pressure drop in mixer there was used Bernoulli’s theorem. Solving obtained equations using MATHCAD found diameter of outlet section of consufer d2 = 0,023 м, vapor pressure inside of mixer p2 = 3,966·105 Па, l2 = 0,128 м. Developed method of calculation is used to determine

  13. Enhancement of photoassimilate utilization by manipulation of starch regulatory enzymes

    Energy Technology Data Exchange (ETDEWEB)

    Okita, Thomas W. [Washington State Univ., Pullman, WA (United States)

    2016-05-11

    ADPglucose pyrophosphorylase (AGPase) and the plastidial starch phosphorylase1 (Pho1) are two regulatory enzymes whose catalytic activities are essential for starch granule synthesis. Conversion of the pre-starch granule to the mature form is dependent on AGPase, which produces ADPglucose, the substrate used by starch synthases. The catalytic activity of AGPase is controlled by small effector molecules and a prime goal of this project was to decipher the role of the two subunit types that comprise the heterotetrameric enzyme structure. Extensive genetic and biochemical studies showed that catalysis was contributed mainly by the small subunit although the large subunit was required for maximum activity. Both subunits were needed for allosteric regulatory properties. We had also demonstrated that the AGPase catalyzed reaction limits the amount of starch accumulation in developing rice seeds and that carbon flux into rice seed starch can be increased by expression of a cytoplasmic-localized, up-regulated bacterial AGPase enzyme form. Results of subsequent physiological and metabolite studies showed that the AGPase reaction is no longer limiting in the AGPase transgenic rice lines and that one or more downstream processes prevent further increases in starch biosynthesis. Further studies showed that over-production of ADPglucose dramatically alters the gene program during rice seed development. Although the expression of nearly all of the genes are down-regulated, levels of a starch binding domain containing protein (SBDCP) are elevated. This SBDCP was found to bind to and inhibit the catalytic activity of starch synthase III and, thereby preventing maximum starch synthesis from occurring. Surprisingly, repression of SBDCP elevated expression of starch synthase III resulting in increasing rice grain weight. A second phase of this project examined the structure-function of Pho1, the enzyme required during the initial phase of pre-starch granule formation and its

  14. Silver nanoparticle (AgNPs) doped gum acacia-gelatin-silica nanohybrid: an effective support for diastase immobilization.

    Science.gov (United States)

    Singh, Vandana; Ahmed, Shakeel

    2012-03-01

    An effective carrier matrix for diastase alpha amylase immobilization has been fabricated by gum acacia-gelatin dual templated polymerization of tetramethoxysilane. Silver nanoparticle (AgNp) doping to this hybrid could significantly enhance the shelf life of the impregnated enzyme while retaining its full bio-catalytic activity. The doped nanohybrid has been characterized as a thermally stable porous material which also showed multipeak photoluminescence under UV excitation. The immobilized diastase alpha amylase has been used to optimize the conditions for soluble starch hydrolysis in comparison to the free enzyme. The optimum pH for both immobilized and free enzyme hydrolysis was found to be same (pH=5), indicating that the immobilization made no major change in enzyme conformation. The immobilized enzyme showed good performance in wide temperature range (from 303 to 323 K), 323 K being the optimum value. The kinetic parameters for the immobilized, (K(m)=10.30 mg/mL, V(max)=4.36 μmol mL(-1)min(-1)) and free enzyme (K(m)=8.85 mg/mL, V(max)=2.81 μmol mL(-1)min(-1)) indicated that the immobilization improved the overall stability and catalytic property of the enzyme. The immobilized enzyme remained usable for repeated cycles and did not lose its activity even after 30 days storage at 40°C, while identically synthesized and stored silver undoped hybrid lost its ~31% activity in 48 h. Present study revealed the hybrids to be potentially useful for biomedical and optical applications. Copyright © 2011 Elsevier B.V. All rights reserved.

  15. Matrix Effect on the Spray Drying Nanoencapsulation of Lippia sidoides Essential Oil in Chitosan-Native Gum Blends.

    Science.gov (United States)

    Paula, Haroldo C B; Oliveira, Erick F; Carneiro, Maria J M; de Paula, Regina C M

    2017-03-01

    Essential oils have many applications in the pharmaceutical, chemical, and food fields, however, their use is limited to the fact that they are very labile, requiring their a priori encapsulation, aiming to preserve their properties.This work reports on the preparation of chitosan-gum nanoparticles loaded with thymol containing Lippia sidoides essential oil, using exudates of Anacardium Occidentale (cashew gum), Sterculia striata (chichá gum), and Anadenanthera macrocarpa trees (angico gum). Nanoparticles were produced by spray drying an emulsion of L. sidoides essential oil and aqueous solution of gums with different chitosan : gum ratios. Samples were characterized by FTIR and UV/VIS spectroscopy, particle size, volume distribution, and zeta potential. The FTIR spectrum showed the main signals of chitosan and the gums. Data obtained revealed that the samples had sizes in the nano range, varying from 17 nm to 800 nm. The zeta potential varied from + 30 mV to - 40 mV. Nanoparticle loading values varied from 6.7 % to 15.6 %, with an average encapsulating efficiency of 62 %, where the samples with high ratios of cashew gum and chichá gum presented high oil loading values. The data revealed that both the chitosan : gum ratio and polysaccharide characteristics play major roles in nanoencapsulation processes. Georg Thieme Verlag KG Stuttgart · New York.

  16. Nicotine chewing gum (2 mg, 4 mg) and cigarette smoking: comparative effects upon vigilance and heart rate.

    Science.gov (United States)

    Parrott, A C; Winder, G

    1989-01-01

    Sixteen male smokers, abstinent the morning before testing, were assessed under four conditions: placebo chewing gum, 2 mg nicotine chewing gum, 4 mg nicotine gum, and cigarette smoking. Placebo gum was administered in the cigarette condition, while sham smoking occurred in the gum conditions. Pre-drug administration and post-drug difference scores were calculated for each assessment measure: rapid visual information processing (RVIP), memory for new information, and heart rate. Nicotine raised heart rate in a significant monotonic dose-related manner (P less than 0.001): placebo +0.2; 2 mg gum +5.1; 4 mg gum +9.8; cigarette +17.5 bpm. Rapid visual information processing target detections were also significantly related to dose (P less than 0.01), with this increased vigilance significant under 4 mg nicotine gum and cigarette smoking. Memory task performance was not significantly affected. Self-reported feelings of alertness/energy were higher while smoking than under placebo or 4 mg gum. Complaints about the taste of the 4 mg nicotine gum were frequent.

  17. Immunogenicity, immunological cross reactivity and non-specific irritant properties of the exudate gums, arabic, karaya and tragacanth.

    Science.gov (United States)

    Strobel, S; Ferguson, A; Anderson, D M

    1986-01-01

    An animal model has been used to investigate the immunogenicity and non-specific irritant properties of exudate gums. The materials studied were four preparations of gum arabic (Acacia spp.), two of gum karaya (Sterculia spp.), two of gum tragacanth (Astralagus spp.) and a residue obtained after ethanol extraction of gum arabic. Groups of animals were intradermally immunized with the gum in complete Freund's adjuvant. Serum antibody levels were measured by an ELISA technique and delayed hypersensitivity responses by a footpad swelling test. Antigenic cross-reactivity within each gum species was tested in a crossover fashion. All gum preparations elicited systemic immune responses after immunization. Further processing reduced immunogenicity, although there was no evidence that systemic immunity to these complex polysaccharide antigens responses could be completely abolished by processing or purification. The ethanolic extract, and some of the gum preparations, particularly tragacanth and karaya, caused considerable footpad swelling when injected intradermally. It is concluded that processing and awareness of subspecies differences can reduce the inherent immunogenicity and potential irritant effects of exudate gums.

  18. Preparation of Acetylated Guar Gum – Unsaturated Polyester Composites & Effect of Water on Their Properties

    Directory of Open Access Journals (Sweden)

    David D’Melo

    2012-07-01

    Full Text Available Guar gum has seen extensive use in blends, however, its application as a filler in thermoset composites has as yet not been investigated. The effect of the addition of guar gum and its acetyl derivatives on the kinetics of water diffusion in unsaturated polyester composites was studied. The effect of water on the mechanical properties of the composites was studied with respect to the nature of filler, filler concentration and time of immersion. All the mechanical properties were observed to decrease on exposure to water. Further, it was observed that acetylated guar gum, with a degree of substitution of 0.21, showed the best mechanical properties, surpassing the other filled composites and that of the pure unsaturated polyester. Thus, acetylated guar gum showed promise as eco-friendly filler in composite formulation.

  19. The relative bioavailability of loratadine administered as a chewing gum formulation in healthy volunteers

    DEFF Research Database (Denmark)

    Nøhr-Jensen, Lene; Damkier, Per; Bidstrup, Tanja Busk

    2006-01-01

    OBJECTIVE: The aim of this study was to investigate the pharmacokinetics of loratadine and its active metabolite desloratadine after single-dose administration of loratadine as a conventional tablet, orally disintegrating tablet (smelt tablet) and a chewing gum formulation with and without...... of medicated chewing gum without collection of saliva and a 30-mg portion of medicated chewing gum with collection of saliva. Blood samples were taken at predefined sampling points 0-24 h after medication, and the plasma concentrations of loratadine and desloratadine were determined by high-performance liquid...... chromatography. Each study period was separated by a wash-out period of at least 7 days. RESULTS: The mean dose-corrected area under the plasma concentration-time curve extrapolated to infinity AUC(0-infinity) for the chewing gum formulation was statistically significantly increased compared to the tablet...

  20. Gum forming olefinic precursors in motor gasoline: a model compound study

    Energy Technology Data Exchange (ETDEWEB)

    Nagpal, J.M.; Joshi, G.C.; Singh, J.; Rastogi, S.N. (Indian Institute of Petroleum, Dehradun (India))

    1994-01-01

    The source of the cracked components in motor gasoline are generally (Fluid Catalytic Cracking) FCC and thermal cracking naphthas incorporated in the gasoline pool. The FCC olefins are predominant in isostructures, while thermal cracking naphthas obtained from visbreaking and coking operations contain substantial amounts of cyclic structures. The contribution of various olefinic structures present in these naphthas are likely to vary. The gum forming tendencies of different types of olefinic structures have been studied by taking model compounds in a known sample matrix through potential gum measurements under accelerated test conditions. Peroxide number values have also been determined on aged sample. Cyclic and dicyclic structures have been found to contribute maximum, towards gum formation tendencies. Branching generally increases the gum formation. However, position of branching plays an important role besides the double bond. Synergistic effects of dienes with straight chain and branched olefins have also been studied. 11 refs., 10 figs., 2 tabs.