WorldWideScience

Sample records for stable radiolytic products

  1. Radiolytic gas production from tritiated waste forms

    International Nuclear Information System (INIS)

    Bibler, N.E.; Orebaugh, E.G.

    1977-07-01

    Radiolytic gas production during long-term storage of tritiated waste was estimated from gamma and alpha radiolysis tests to determine the extent of pressurization in sealed containers. Two forms of simulated wastes were irradiated with 60 Co gamma rays or 244 Cm alpha particles: concrete for solidification of tritiated water and vermiculite for solidification of tritiated octane or vacuum pump oil. For concrete, the gamma and alpha radiolysis results predicted that H 2 will be formed by tritium beta particles with an initial rate of 0.1 to 0.3 molecule for every 100 eV of energy absorbed. Also, as the H 2 pressure increases, this 100-eV yield decreases because of a reaction removing H 2 . Eventually, a steady state pressure that depends on the radiation intensity will be attained. For intensities less than 10 5 rads/h, the steady state pressure will be less than 20 psi. O 2 in the air sealed with the concrete will be almost completely depleted, and N 2 will be unaffected. For the organic materials sorbed onto vermiculite, the gamma and alpha radiolysis results predicted that H 2 and traces of CH 4 and CO 2 will be produced. For tritium beta particles, the 100-eV yields for H 2 based on energy sorbed by the organic materials are 4.4 for octane and 2.2 for vacuum pump oil. In the containers, steady state H 2 pressure will not be attained at pressures up to at least 200 psi. As with the concrete, O 2 will be nearly completely depleted and N 2 will be unaffected. The 100-eV yield for H 2 production was used to calculate pressure increases in conceptual tritiated waste packages. 13 figures

  2. Radiolytic hydrogen production in the subseafloor basaltic aquifer

    Directory of Open Access Journals (Sweden)

    Mary E Dzaugis

    2016-02-01

    Full Text Available Hydrogen (H2 is produced in geological settings by dissociation of water due to radiation from radioactive decay of naturally occurring uranium (238U, 235U, thorium (232Th and potassium (40K. To quantify the potential significance of radiolytic H2 as an electron donor for microbes within the South Pacific subseafloor basaltic aquifer, we use radionuclide concentrations of 43 basalt samples from IODP Expedition 329 to calculate radiolytic H2 production rates in basement fractures. The samples are from three sites with very different basement ages and a wide range of alteration types. U, Th and K concentrations vary by up to an order of magnitude from sample to sample at each site. Comparison of our samples to each other and to the results of previous studies of unaltered East Pacific Rise basalt suggests that significant variations in radionuclide concentrations are due to differences in initial (unaltered basalt concentrations (which can vary between eruptive events and post-emplacement alteration. In our samples, there is no clear relationship between alteration type and calculated radiolytic yields. Local maxima in U, Th, and K produce hotspots of H2 production, causing calculated radiolytic rates to differ by up to a factor of 80 from sample to sample. Fracture width also greatly influences H2 production, where microfractures are hotspots for radiolytic H2 production. For example, H2 production rates normalized to water volume are 190 times higher in 1 μm wide fractures than in fractures that are 10 cm wide. To assess the importance of water radiolysis for microbial communities in subseafloor basaltic aquifers, we compare electron transfer rates from radiolysis to rates from iron oxidation in subseafloor basalt. Radiolysis appears likely to be a more important electron donor source than iron oxidation in old (>10 Ma basement basalt. Radiolytic H2 production in the volume of water adjacent to a square cm of the most radioactive SPG basalt may

  3. Radiolytic production of chemical fuels in fusion reactor systems

    Energy Technology Data Exchange (ETDEWEB)

    Fish, J D

    1977-06-01

    Miley's energy flow diagram for fusion reactor systems is extended to include radiolytic production of chemical fuel. Systematic study of the economics and the overall efficiencies of fusion reactor systems leads to a criterion for evaluating the potential of radiolytic production of chemical fuel as a means of enhancing the performance of a fusion reactor system. The ecumenicity of the schema is demonstrated by application to (1) tokamaks, (2) mirror machines, (3) theta-pinch reactors, (4) laser-heated solenoids, and (5) inertially confined, laser-pellet devices. Pure fusion reactors as well as fusion-fission hybrids are considered.

  4. Radiolytic production of chemical fuels in fusion reactor systems

    International Nuclear Information System (INIS)

    Fish, J.D.

    1977-06-01

    Miley's energy flow diagram for fusion reactor systems is extended to include radiolytic production of chemical fuel. Systematic study of the economics and the overall efficiencies of fusion reactor systems leads to a criterion for evaluating the potential of radiolytic production of chemical fuel as a means of enhancing the performance of a fusion reactor system. The ecumenicity of the schema is demonstrated by application to (1) tokamaks, (2) mirror machines, (3) theta-pinch reactors, (4) laser-heated solenoids, and (5) inertially confined, laser-pellet devices. Pure fusion reactors as well as fusion-fission hybrids are considered

  5. Influence of radiolytic degradation products from organic phase

    International Nuclear Information System (INIS)

    Azevedo, H.L.P. de.

    1980-01-01

    The influence of primary and secondary degradation products from TBP - dodecane on zirconium extraction is studied. The presence of radiolytical degradation at organic phase, in systems of initial concentration of HNO 3 1 and 4M, and absorbed γ radiation doses from 0,5 to 4,5 Wh/l, lead to an increase of zirconium extraction, being the HDBP the main product of degradation responsable by this effect. The influence of secondary degradation products is significative in systems of HNO 3 1M initial concentration. The formation of precipitator in extractions of Zr in HNO 3 1M with irradiated TBP-dodecane was observed. (M.C.K.) [pt

  6. Detection of radiolytic products by electrochemical methods

    International Nuclear Information System (INIS)

    Gonzalez-Velasco, J.

    1979-01-01

    This study demonstrates that the values of the rest potential of a platinum electrode submerged in an alkaline electrolyte (similar behaviour is also observed for an acidic one), can give a qualitative idea of the predominance in solution of radicaloid products that are oxidant and reducing in character. A simultaneous recording of potential sweep diagrams gives more precise information on the presence and characteristics of these radicals. (author)

  7. Gamma irradiation of cytosine in aerated aqueous solution. Identification of two new radiolytic products

    International Nuclear Information System (INIS)

    Polverelli, M.

    1975-01-01

    After gamma irradiation of cytosine in aerated aqueous solutions, two new radiolytic products were isolated and identified: N-formyl-biuret and carbamoyl-l-hydroxy-5-hydantoin. The position and importance of those products in the radiolytic degradation of cytosine were examined [fr

  8. Effect of radiolytic products on bacteria in a food system

    International Nuclear Information System (INIS)

    Dickson, J.S.; Maxcy, R.B.

    1984-01-01

    Inhibitory effects of radiolytic products were studied using Escherichia coli, Pediococcus cerevisiae, and two radiation-resistant microorganisms, an isolate of Moraxella-Acinetobacter and a Micrococcus sp. End Products of an irradiation dose of 300 Krads completely inhibited resistant organisms on an experimental medium with a very low concentration of nutrients. Plate count agar, with higher nutrient concentration, required 600 Krads to produce the same inhibition. On the same medium, radiation-sensitive organisms could tolerate products generated by a 1000 Krad dose. However, no inhibition could be detected when either Escherichia coli or Moraxella-Acinetobacter was incubated at 5 0 C on the surface of fresh meat irradiated to 1500 Krad. The effects of inhibitory products in culture media could be mitigated by the addition of catalase or sodium pyruvate. 19 references, 2 figures, 4 tables

  9. Radiolytic products of irradiated authentic fatty acids and triacylglycerides

    Energy Technology Data Exchange (ETDEWEB)

    Kim, K.-S. E-mail: kskim@mail.chosun.ac.kr; Lee, Jeong-Min; Seo, Hye-Young; Kim, Jun-Hyoung; Song, Hyun-Pa; Byun, Myung-Woo; Kwon, Joong-Ho

    2004-10-01

    Radiolytic products of authentic fatty acids (palmitic, stearic, oleic, linoleic and linolenic acids) and triacylglycerides (tripalmitin, tristearin, triolein, trilinolein and trilinolenin) were determined. Concentrations of hydrocarbons from the saturated fatty acids were higher than the unsaturated fatty acids. Authentic fatty acids were mainly decomposed in the {alpha}-carbon position and C{sub n-1} hydrocarbons occurred in higher than C{sub n-2} hydrocarbons. Concentrations of 2-alkylcyclobutanones from the saturated fatty acids were lower than the unsaturated fatty acids. Concentrations of hydrocarbons from tripalmitin and tristearin were not a significant change compared with triolein, trilinolein and trilinolenin. For all triacylglycerides except triolein, C{sub n-1} hydrocarbons were higher than C{sub n-2} hydrocarbons. Radioproduction rates of 2-alkylcyclobutanones from tripalmitin and tristearin were higher than triolein, trilinolein and trilinolenin.

  10. Radiolytic products of irradiated authentic fatty acids and triacylglycerides

    International Nuclear Information System (INIS)

    Kim, K.-S.; Lee, Jeong-Min; Seo, Hye-Young; Kim, Jun-Hyoung; Song, Hyun-Pa; Byun, Myung-Woo; Kwon, Joong-Ho

    2004-01-01

    Radiolytic products of authentic fatty acids (palmitic, stearic, oleic, linoleic and linolenic acids) and triacylglycerides (tripalmitin, tristearin, triolein, trilinolein and trilinolenin) were determined. Concentrations of hydrocarbons from the saturated fatty acids were higher than the unsaturated fatty acids. Authentic fatty acids were mainly decomposed in the α-carbon position and C n-1 hydrocarbons occurred in higher than C n-2 hydrocarbons. Concentrations of 2-alkylcyclobutanones from the saturated fatty acids were lower than the unsaturated fatty acids. Concentrations of hydrocarbons from tripalmitin and tristearin were not a significant change compared with triolein, trilinolein and trilinolenin. For all triacylglycerides except triolein, C n-1 hydrocarbons were higher than C n-2 hydrocarbons. Radioproduction rates of 2-alkylcyclobutanones from tripalmitin and tristearin were higher than triolein, trilinolein and trilinolenin

  11. Structure elucidation and toxicity analyses of the radiolytic products of aflatoxin B{sub 1} in methanol-water solution

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Feng [Institute of Agro-food Science and Technology of Chinese Academy of Agricultural Sciences, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China); Key Opening Laboratory of Agricultural Products Processing and Quality Control, Ministry of Agriculture, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China); Graduate School of Chinese Academy of Agricultural Sciences, 12th Zhongguancun South Road, Hai Dian District, Beijing 100081 (China); Xie, Fang [Institute of Agro-food Science and Technology of Chinese Academy of Agricultural Sciences, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China); Key Opening Laboratory of Agricultural Products Processing and Quality Control, Ministry of Agriculture, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China); Xue, Xiaofeng [Bee Research Institute of Chinese Academy of Agricultural Sciences, 1st Xiangshan North Ditch, Hai Dian District, Beijing 100093 (China); Wang, Zhidong; Fan, Bei [Institute of Agro-food Science and Technology of Chinese Academy of Agricultural Sciences, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China); Key Opening Laboratory of Agricultural Products Processing and Quality Control, Ministry of Agriculture, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China); Ha, Yiming, E-mail: wxfay2011@hotmail.com [Institute of Agro-food Science and Technology of Chinese Academy of Agricultural Sciences, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China); Key Opening Laboratory of Agricultural Products Processing and Quality Control, Ministry of Agriculture, 2nd Yuanmingyuan West Road, Hai Dian District, Beijing 100193 (China)

    2011-09-15

    Highlights: {yields} Radiolytic products of aflatoxin B{sub 1} were produced under gamma irradiation. {yields} Seven key radiolytic products were structure-elucidated. {yields} Free-radical species in radiolytic solution resulted in the formation of products. {yields} Based on the structure-activity relationship analysis, the toxicity of radiolytic products was significantly reduced compared with that of AFB{sub 1}. {yields} The addition reaction on furan ring double bond was the reason for the reduced toxicity. - Abstract: The identification of the radiolytic products of mycotoxins is a key issue in the feasibility study of gamma ray radiation detoxification. Methanol-water solution (60:40, v/v) spiked with aflatoxin B{sub 1} (AFB{sub 1}; 20 mg L{sup -1}) was irradiated with Co{sup 60} gamma ray to generate radiolytic products. Liquid chromatography-quadruple time-of-flight mass spectrometry was applied to identify the radiolytic products of AFB{sub 1}. Accurate mass and proposed molecular formulas with a high-matching property of more than 20 radiolytic products were obtained. Seven key radiolytic products were proposed based on the molecular formulas and tandem mass spectrometry spectra. The analyses of toxicity and formation pathways were proposed based on the structure of the radiolytic products. The addition reaction caused by the free-radical species in the methanol-water solution resulted in the formation of most radiolytic products. Based on the structure-activity relationship analysis, the toxicity of radiolytic products was significantly reduced compared with that of AFB{sub 1} because of the addition reaction that occurred on the double bond in the terminal furan ring. For this reason, gamma irradiation is deemed an effective tool for the detoxification of AFB{sub 1}.

  12. Global distribution of radiolytic H2 production in marine sediment and implications for subsurface life

    Science.gov (United States)

    Sauvage, J.; Flinders, A. F.; Spivack, A. J.; D'Hondt, S.

    2017-12-01

    We present the first global estimate of radiolytic H2production in marine sediment. Knowledge of microbial electron donor production rates is critical to understand the bioenergetics of Earth's subsurface ecosystems In marine sediment, radiolysis of water by radiation from naturally occurring radionuclides leads to production of reduced (H2) and oxidized (H2O2, O2) species. Water radiolysis is catalyzed by marine sediment. The magnitude of catalysis depends on sediment composition and radiation type. Deep-sea clay is especially effective at enhancing H2 yields, increasing yield by more than an order of magnitude relative to pure water. This previously unrecognized catalytic effect of geological materials on radiolytic H2 production is important for fueling microbial life in the subseafloor, especially in sediment with high catalytic power. Our estimate of radiolytic H2 production is based on spatially integrating a previously published model and uses (i) experimentally constrained radiolytic H2 yields for the principal marine sediment types, (ii) bulk sediment radioactive element content of sediment cores in three ocean basins (N. Atlantic, N. and S. Pacific), and global distributions of (iii) seafloor lithology, (iv) sediment porosity, and (v) sediment thickness. We calculate that global radiolytic H2 production in marine sediment is 1.6E+12 mol H2 yr-1. This production rate is small relative to the annual rate of photosynthetic organic-matter production in the surface ocean. The globally integrated ratio of radiolytic H2 production relative to photosynthetic primary production is 4.1E-4, based on electron equivalences. Although small relative to global photosynthetic biomass production, sediment-catalyzed production of radiolytic products is significant in the subseafloor. Our analysis of 9 sites in the N. Atlantic, N. and S. Pacific suggests that H2 is the primary microbial fuel in organic-poor sediment older than a few million years; at these sites, calculated

  13. HPLC profiling of radiolytic products of nitrobenzene - carbon tetrachloride - water two-phase systems

    International Nuclear Information System (INIS)

    Sahoo, M.K.; Kuruc, J.; Svec, A.; Cech, R.; Hutta, M.

    1992-01-01

    Radiolytic products of the two-phase systems of nitrobenzene - carbon tetrachloride - water mixtures have been identified using HPLC adsorption chromatography on SEPARON SIX silica gel column under an elution gradient from n-hexane to ethyl acetate. That the product formation is a function of the mixture composition is indicated by the chromatograms. Para-nitrophenol constitutes one of the major radiolytic products in the system where the volume ratio of nitrobenzene is more than that of carbon tetrachloride and its radiation yield is dependent on the volume ratio of the aqueous phase. (author) 10 refs.; 4 figs.; 1 tabs

  14. Characterization of radiolytically generated degradation products in the strip section of a TRUEX flowsheet

    Energy Technology Data Exchange (ETDEWEB)

    Peterman, Dean R. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Olson, Lonnie G. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Groenewold, Gary S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); McDowell, Rocklan G. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Tillotson, Richard D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Law, Jack D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2013-08-01

    This report presents a summary of the work performed to meet the FCRD level 2 milestone M3FT-13IN0302053, “Identification of TRUEX Strip Degradation.” The INL radiolysis test loop has been used to identify radiolytically generated degradation products in the strip section of the TRUEX flowsheet. These data were used to evaluate impact of the formation of radiolytic degradation products in the strip section upon the efficacy of the TRUEX flowsheet for the recovery of trivalent actinides and lanthanides from acidic solution. The nominal composition of the TRUEX solvent used in this study is 0.2 M CMPO and 1.4 M TBP dissolved in n-dodecane and the nominal composition of the TRUEX strip solution is 1.5 M lactic acid and 0.050 M diethylenetriaminepentaacetic acid. Gamma irradiation of a mixture of TRUEX process solvent and stripping solution in the test loop does not adversely impact flowsheet performance as measured by stripping americium ratios. The observed increase in americium stripping distribution ratios with increasing absorbed dose indicates the radiolytic production of organic soluble degradation compounds.

  15. LC-MS analysis in the e-beam and gamma radiolysis of metoprolol tartrate in aqueous solution: Structure elucidation and formation mechanism of radiolytic products

    Energy Technology Data Exchange (ETDEWEB)

    Slegers, Catherine [Unite d' Analyse Chimique et Physico-chimique des Medicaments, Universite Catholique de Louvain, CHAM 72.30, Avenue E. Mounier, 72, B-1200, Brussels (Belgium)]. E-mail: catherine.slegers@skynet.be; Maquille, Aubert [Unite d' Analyse Chimique et Physico-chimique des Medicaments, Universite Catholique de Louvain, CHAM 72.30, Avenue E. Mounier, 72, B-1200, Brussels (Belgium); Deridder, Veronique [Unite d' Analyse Chimique et Physico-chimique des Medicaments, Universite Catholique de Louvain, CHAM 72.30, Avenue E. Mounier, 72, B-1200, Brussels (Belgium); Sonveaux, Etienne [Unite de Chimie Pharmaceutique et de Radiopharmacie, Universite Catholique de Louvain, Brussels (Belgium); Habib Jiwan, Jean-Louis [Laboratoire de Spectrometrie de Masse, Universite Catholique de Louvain, Louvain-La-Neuve (Belgium); Tilquin, Bernard [Unite d' Analyse Chimique et Physico-chimique des Medicaments, Universite Catholique de Louvain, CHAM 72.30, Avenue E. Mounier, 72, B-1200, Brussels (Belgium)

    2006-09-15

    E-beam and gamma products from the radiolysis of aqueous solutions of ({+-})-metoprolol tartrate, saturated in nitrogen, are analyzed by HPLC with on-line mass and UV detectors. The structures of 10 radiolytic products common to e-beam and gamma irradiations are elucidated by comparing their fragmentation pattern to that of ({+-})-metoprolol. Two of the radiolytic products are also metabolites. Different routes for the formation of the radiolytic products are proposed.

  16. Time extrapolation of radiolytic degradation product kinetics: the case of polyurethane

    International Nuclear Information System (INIS)

    Dannoux, A.

    2007-02-01

    The prediction of the environmental impact of organic materials in nuclear waste geological storage needs knowledge of radiolytic degradation mechanisms and kinetics in aerobic and anaerobic conditions. In this framework, the effect of high doses (> MGy) and the variation of dose rate have to be considered. The material studied is a polyurethane composed of polyether soft segment and aromatic hard segments. Mechanisms were built on the analysis of material submitted to irradiations of simulation (high energy electrons and gamma radiation) by FTIR spectroscopy and gaseous and liquid degradation products by gas mass spectrometry and size exclusion chromatography. The electron paramagnetic resonance study of radical process and the determination of oxygen consumption and gas formation radiolytic yields allowed us to acquire kinetic data and to estimate dose rate and high doses effects. The polyurethane radio-oxidation mainly concerns soft segments and induced cross-linkings and production by scissions of oxidised compounds (esters, alcohols, carboxylic acids). The kinetic of radical termination is rapid and the dose rate effect is limited. After 10 MGy, branching and scission reactions are in equilibrium and low molecular weight products accumulate. At last, the degradation products release in water is influenced by the oxidation rate and the temperature. After 10 MGy, the soluble fraction is stabilised at 25%. The water soluble products identified by electro-spray ionisation mass spectrometry (alcohols, aldehydes, carboxylic acids) potentially formed complexes with radionuclides. (author)

  17. Radiolytic gas production from concrete containing Savannah River Plant waste

    International Nuclear Information System (INIS)

    Bibler, N.E.

    1978-01-01

    To determine the extent of gas production from radiolysis of concrete containing radioactive Savannah River Plant waste, samples of concrete and simulated waste were irradiated by 60 Co gamma rays and 244 Cm alpha particles. Gamma radiolysis simulated radiolysis by beta particles from fission products in the waste. Alpha radiolysis indicated the effect of alpha particles from transuranic isotopes in the waste. With gamma radiolysis, hydrogen was the only significant product; hydrogen reached a steady-state pressure that increased with increasing radiation intensity. Hydrogen was produced faster, and a higher steady-state pressure resulted when an organic set retarder was present. Oxygen that was sealed with the wastes was depleted. Gamma radiolysis also produced nitrous oxide gas when nitrate or nitrite was present in the concrete. With alpha radiolysis, hydrogen and oxygen were produced. Hydrogen did not reach a steady-state pressure at 137 Cs and 90 Sr), hydrogen will reach a steady-state pressure of 8 to 28 psi, and oxygen will be partially consumed. These predictions were confirmed by measurement of gas produced over a short time in a container of concrete and actual SRP waste. The tests with simulated waste also indicated that nitrous oxide may form, but because of the low nitrate or nitrite content of the waste, the maximum pressure of nitrous oxide after 300 years will be 238 Pu and 239 Pu will predominate; the hydrogen and oxygen pressures will increase to >200 psi

  18. DOSIMETRY MODELING FOR PREDICTING RADIOLYTIC PRODUCTION AT THE SPENT FUEL - WATER INTERFACE

    International Nuclear Information System (INIS)

    W.H. Miller

    2006-01-01

    The radiolysis of water in contact with spent nuclear fuel (SNF) will produce oxidants and reductants that can affect the dissolution of the fuel in a geologic disposal site. These products are created by initial radiolytic species which are a function of the type of radiation being emitted by the SNF, i.e. alpha, beta and/or gamma, as well as the energy of this radiation, the fuel grain size (and resulting surface-to-volume ratio) and the fuel-to-water ratio. These products interact with the surface of the fuel, creating new species and ultimately affecting the dissolution rate. The objective of the work reported here is to develop a systematic dosimetry model to determine the dose to water from the SNF as a function of these variables. This dose is calculated for different radiation types as a function of decay for the average fuel composition expected at Yucca Mountain. From these dose calculations the production rate of initial radiolytic products can be estimated. This data provides the basis for subsequent determination of the resulting chemical interactions at the fuel/water interface predicted by published theoretical and experimental data

  19. DOSIMETRY MODELING FOR PREDICTING RADIOLYTIC PRODUCTION AT THE SPENT FUEL-WATER INTERFACE

    Energy Technology Data Exchange (ETDEWEB)

    W.H. Miller

    2006-03-03

    The radiolysis of water in contact with spent nuclear fuel (SNF) will produce oxidants and reductants that can affect the dissolution of the fuel in a geologic disposal site. These products are created by initial radiolytic species which are a function of the type of radiation being emitted by the SNF, i.e. alpha, beta and/or gamma, as well as the energy of this radiation, the fuel grain size (and resulting surface-to-volume ratio) and the fuel-to-water ratio. These products interact with the surface of the fuel, creating new species and ultimately affecting the dissolution rate. The objective of the work reported here is to develop a systematic dosimetry model to determine the dose to water from the SNF as a function of these variables. This dose is calculated for different radiation types as a function of decay for the average fuel composition expected at Yucca Mountain. From these dose calculations the production rate of initial radiolytic products can be estimated. This data provides the basis for subsequent determination of the resulting chemical interactions at the fuel/water interface predicted by published theoretical and experimental data.

  20. Complexation of Cu2+, Ni2+ and UO22+ by radiolytic degradation products of bitumen

    International Nuclear Information System (INIS)

    Loon, L.R. Van; Kopajtic, Z.

    1990-05-01

    The radiolytic degradation of bitumen was studied under conditions which reflect those which will exist in the near field of a cementitious radioactive waste repository. The potential complexation capacity of the degradation products was studied and complexation experiments with Cu 2+ , Ni 2+ and UO 2 2+ were performed. In general 1:1 complexes with Cu 2+ , Ni 2+ and UO 2 2+ , with log K values of between 5.7 and 6.0 for Cu 2+ , 4.2 for Ni 2+ and 6.1 for UO 2 2+ , were produced at an ionic strength of 0.1 M. The composition of the bitumen water was analysed by GC-MS and IC. The major proportion of the bitumen degradation products in solution were monocarboxylic acids (acetic acid, formic acid, myric acid, stearic acid ...), dicarboxylic acids (oxalic acid, phthalic acid) and carbonates. The experimentally derived log K data are in good agreement with the literature and suggest that oxalate determines the speciation of Cu 2+ , Ni 2+ and UO 2 2+ in the bitumen water below pH=7. However, under the high pH conditions typical of the near field of a cementitious repository, competition with OH-ligands will be large and oxalate, therefore, will not play a significant role in the speciation of radionuclides. The main conclusion of the study is that the radiolytic degradation products of bitumen will have no influence on radionuclide speciation in a cementitious near field and, as such, need not to be considered in the appropriate safety assessment models. (author) 12 figs., 11 tabs., 31 refs

  1. Calculus of radiolytic products generation in water due to alpha radiation. Determination of the spent nuclear fuels matrix alteration rate Determination of velocity of spent fuel matrix

    International Nuclear Information System (INIS)

    Quinones, J.; Serrano, J.; Diaz Arocas, P.; Rodriguez Almazan, J. L.; Bruno, J.; Cera, E.; Merino, J.; Esteban, J. A.; Martinez-Esparza, A.

    2000-01-01

    The generation of radiolytic products as a result of alpha radiation in the surface of the spent fuel is a key process in order to understand how the it becomes degraded in repository conditions. The present work has established a radiolytic model based on a set of reactions involving fuel oxidation-dissolution and radiolytic products recombination. It also includes the decrease of the dose rates as the main alpha emitters decay away. Four cases, with varying parameters of the system, have been assessed. The results show a decrease in both the concentration of the radiolytic products in the gap water and the degradation of the fuel matrix. It has been estimated that in the period of the evaluation (10''6 years) up to 52% of the pellet is altered in the conservative cases, whereas only 11% is altered in the realistic cases. No significant differences were observed when the carbonates reactions were included in the system. (Author)

  2. Radiation effects in moist-air systems and the influence of radiolytic product formation on nuclear waste glass corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Wronkiewicz, D.J.; Bates, J.K.; Buck, E.C.; Hoh, J.C.; Emery, J.W. [Argonne National Lab., IL (United States). Chemical Technology Div.; Wang, L.M. [Univ. of New Mexico, Albuquerque, NM (United States). Dept. of Geology

    1997-07-01

    Ionizing radiation may affect the performance of glass in an unsaturated repository site by interacting with air, water vapor, or liquid water to produce a variety of radiolytic products. Tests were conducted to examine the effects of radiolysis under high gas/liquid ratios. Results indicate that nitrate is the predominant radiolytic product produced following both gamma and alpha radiation exposure, with lesser amounts of nitrite and carboxylic acids. The formation of nitrogen acids during exposure to long-lived, alpha-particle-emitting transuranic elements indicates that these acids may play a role in influencing nuclear waste form reactions in a long-term unsaturated disposal scenario. Experiments were also conducted with samples that simulate the composition of Savannah River Plant nuclear waste glasses. Radiolytic product formation in batch tests (340 m{sup {minus}1}, 90 C) resulted in a small increase in the release rates of many glass components, such as alkali and alkaline earth elements, although silicon and uranium release rates were slightly reduced indicating an overall beneficial effect of radiation on waste form stability. The radiolytic acids increased the rate of ion exchange between the glass and the thin film of condensate, resulting in accelerated corrosion rates for the glass. The paragenetic sequence of alteration phases formed on both the irradiated and nonirradiated glass samples reacted in the vapor hydration tests matches closely with those developed during volcanic glass alteration in naturally occurring saline-alkaline lake systems. This correspondence suggests that the high temperatures used in these tests have not changed the underlying glass reaction mechanism relate to that which controls glass reactions under ambient surficial conditions.

  3. Radiation effects in moist-air systems and the influence of radiolytic product formation on nuclear waste glass corrosion

    International Nuclear Information System (INIS)

    Wronkiewicz, D.J.; Bates, J.K.; Buck, E.C.; Hoh, J.C.; Emery, J.W.; Wang, L.M.

    1997-07-01

    Ionizing radiation may affect the performance of glass in an unsaturated repository site by interacting with air, water vapor, or liquid water to produce a variety of radiolytic products. Tests were conducted to examine the effects of radiolysis under high gas/liquid ratios. Results indicate that nitrate is the predominant radiolytic product produced following both gamma and alpha radiation exposure, with lesser amounts of nitrite and carboxylic acids. The formation of nitrogen acids during exposure to long-lived, alpha-particle-emitting transuranic elements indicates that these acids may play a role in influencing nuclear waste form reactions in a long-term unsaturated disposal scenario. Experiments were also conducted with samples that simulate the composition of Savannah River Plant nuclear waste glasses. Radiolytic product formation in batch tests (340 m -1 , 90 C) resulted in a small increase in the release rates of many glass components, such as alkali and alkaline earth elements, although silicon and uranium release rates were slightly reduced indicating an overall beneficial effect of radiation on waste form stability. The radiolytic acids increased the rate of ion exchange between the glass and the thin film of condensate, resulting in accelerated corrosion rates for the glass. The paragenetic sequence of alteration phases formed on both the irradiated and nonirradiated glass samples reacted in the vapor hydration tests matches closely with those developed during volcanic glass alteration in naturally occurring saline-alkaline lake systems. This correspondence suggests that the high temperatures used in these tests have not changed the underlying glass reaction mechanism relate to that which controls glass reactions under ambient surficial conditions

  4. Time extrapolation of radiolytic degradation product kinetics: the case of polyurethane; Extrapolation dans le temps des cinetiques de production des produits de degradation radiolytique: application a un polyurethane

    Energy Technology Data Exchange (ETDEWEB)

    Dannoux, A

    2007-02-15

    The prediction of the environmental impact of organic materials in nuclear waste geological storage needs knowledge of radiolytic degradation mechanisms and kinetics in aerobic and anaerobic conditions. In this framework, the effect of high doses (> MGy) and the variation of dose rate have to be considered. The material studied is a polyurethane composed of polyether soft segment and aromatic hard segments. Mechanisms were built on the analysis of material submitted to irradiations of simulation (high energy electrons and gamma radiation) by FTIR spectroscopy and gaseous and liquid degradation products by gas mass spectrometry and size exclusion chromatography. The electron paramagnetic resonance study of radical process and the determination of oxygen consumption and gas formation radiolytic yields allowed us to acquire kinetic data and to estimate dose rate and high doses effects. The polyurethane radio-oxidation mainly concerns soft segments and induced cross-linkings and production by scissions of oxidised compounds (esters, alcohols, carboxylic acids). The kinetic of radical termination is rapid and the dose rate effect is limited. After 10 MGy, branching and scission reactions are in equilibrium and low molecular weight products accumulate. At last, the degradation products release in water is influenced by the oxidation rate and the temperature. After 10 MGy, the soluble fraction is stabilised at 25%. The water soluble products identified by electro-spray ionisation mass spectrometry (alcohols, aldehydes, carboxylic acids) potentially formed complexes with radionuclides. (author)

  5. Hydrogen radiolytic production in light and heavy water mixtures under conditions similar to LOCA (loss of coolant accidents)

    International Nuclear Information System (INIS)

    Garcia Rodenas, L.; Ali, S.P.; Liberman, S.J.

    1987-01-01

    H 2 , HD and D 2 radiolytic yield in heavy and light water mixtures has been determined to supply the necessary data which will allow to make a realistic estimation of the solution of such gas under LOCA conditions as a function of time. (Author)

  6. GC-FTIR-MS analysis of volatile radiolytic products in the radiolysis of nitroaniline

    International Nuclear Information System (INIS)

    Kuruc, J.; Sahoo, M.K.; Kubinec, R.

    1993-01-01

    A good deal of products formed in the γ-radiolysis of isomeric nitroaniline solutions in carbon tetrachloride have been identified using GC-FTIR-MS technique. Tetrachloroethylene, chlorobenzene, hexachloroethane isomeric di-, tri- and tetrachlorobenzenes and chloroisocyanatobenzenes are among the important products formed in the radiolysis. Formation of dichlorobenzene is the result of ipso-substitution of both the nitro and aniline group by chlorine atom and the subsequent chloration of dichlorobenzene results in the formation of polychlorobenzenes. Chloroisocyanatobenzene is proposed to be the product arising from the interaction of dichlorocarbene and the nitro group of nitroaniline followed by chlorination of the resulting product, isocyanatobenzene. A 94% yield of undissolved 1,2-aminonitrobenzene chloride salt is obtained from the radiolysis of o-nitroaniline solution in carbon tetrachloride with a radiation yield of 1.83 molecules per 100 eV absorbed energy for an irradiation dose of 267 kGy. (author) 9 refs.; 3 figs.; 2 tabs

  7. Analysis of the radiolytic products on high-dose irradiated food and packing materials

    International Nuclear Information System (INIS)

    Kim, Kyong Su; Shim, Sung Lye; Chung, In Sun

    2010-04-01

    The aims of this study were to prepare the government approval for the extension of food irradiation item to food or its products, to promote the industrial application of radiation technology, and to apply basic data in policy for introduction of irradiation. The change of hydrocarbons by irradiation was evaluated for the detection of irradiated meat. The results showed that hydrocarbons were detected in all of irradiated samples, but these hydrocarbons were not detected in non-irradiated samples. There were no difference between vacuum and N 2 - packaging. According to fatty acid compounds and degradation pathway of beef and pork, it could be deliberated that a great amount of produced hydrocarbons such as 8-heptadenene and 1,7-hexadecadien were able to be used as identification factor of irradiated meat. Effects of γ-irradiation on the volatile organic compounds in agricultural products were determined by analyzing changes of volatile composition. The composition of volatile organic compounds were little changed, but few specific compounds induced by γ-irradiation were identified. The variations of concentration in irradiated samples identified in this study could be due to the radiation sensitivity of compounds with the dose used. Effects of γ-irradiation on the volatile compounds in packaging materials were determined by analyzing changes of volatile composition. In polyethylene and polypropylene, 1,3-DBB was identified only in irradiated samples. Levels of 1,3-DBB increased with increasing irradiation doses. These results suggest may be useful in evaluation of γ-irradiation effects on food packaging materials

  8. Analysis of the radiolytic products on high-dose irradiated food and packing materials

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyong Su; Shim, Sung Lye; Chung, In Sun [Chosun University, Gwangju (Korea, Republic of)

    2010-04-15

    The aims of this study were to prepare the government approval for the extension of food irradiation item to food or its products, to promote the industrial application of radiation technology, and to apply basic data in policy for introduction of irradiation. The change of hydrocarbons by irradiation was evaluated for the detection of irradiated meat. The results showed that hydrocarbons were detected in all of irradiated samples, but these hydrocarbons were not detected in non-irradiated samples. There were no difference between vacuum and N{sub 2}- packaging. According to fatty acid compounds and degradation pathway of beef and pork, it could be deliberated that a great amount of produced hydrocarbons such as 8-heptadenene and 1,7-hexadecadien were able to be used as identification factor of irradiated meat. Effects of {gamma}-irradiation on the volatile organic compounds in agricultural products were determined by analyzing changes of volatile composition. The composition of volatile organic compounds were little changed, but few specific compounds induced by {gamma}-irradiation were identified. The variations of concentration in irradiated samples identified in this study could be due to the radiation sensitivity of compounds with the dose used. Effects of {gamma}-irradiation on the volatile compounds in packaging materials were determined by analyzing changes of volatile composition. In polyethylene and polypropylene, 1,3-DBB was identified only in irradiated samples. Levels of 1,3-DBB increased with increasing irradiation doses. These results suggest may be useful in evaluation of {gamma}-irradiation effects on food packaging materials

  9. Radiolytic gas production during long-term storage of nuclear wastes

    International Nuclear Information System (INIS)

    Bibler, N.E.

    1976-01-01

    Gases produced by in situ radiolysis of sealed solidified nuclear wastes during long-term storage could conceivably breach containment. Therefore, candidate waste forms (matrices containing simulated nuclear wastes) were irradiated with 60 Co-γ and 244 Cm-α radiation. These forms were: cement containing simulated fission product sludges, vermiculite containing organic liquids, and cellulosics contaminated with α-emitting transuranic isotopes. For cement waste forms exposed to γ-radiolysis, an equilibrium hydrogen pressure was reached that was dose rate dependent. For α-radiolysis, equilibrium was not reached. With organic wastes (n-octane on vermiculite), H 2 and traces of CO 2 and CH 4 were produced, and O 2 was consumed with both radiations. Only energy absorbed by the organic material was effective in producing H 2 . At low dose rates with both α- and γ-irradiations, G(H 2 ) was 4.5 and G(-O 2 ) was 5.0. Also, equilibrium was not obtained. For cellulosic material, H 2 , CO 2 , and CO were produced in the ratio of 1.0:0.7:0.3, and O 2 was consumed. With α-radiolysis, G(gas) was dose dependent; measured values ranged from 2.2 to 0.6 as the dose increased. Implications of all these results on long-term storage of radioactive waste are discussed. Some data from an actual nuclear wasteform are also presented

  10. Monitoring of gamma radiolytic degradation products of methoxychlor pesticide in water by solid phase micro-extraction using hplc and GC-MS (abstract)

    International Nuclear Information System (INIS)

    Butt, S.B.; Zafar, A.

    2011-01-01

    Monitoring, removal and management of toxic chemicals is an essential area of study regarding sustainable progress. Different approaches are adopted to eliminate these water born toxics from water and waste water. Among these gamma radiolytic is an emerging option. This ionization radiation generates highly reactive radicals that reacts with pollutants and hence eliminates these. A solid-phase micro-extraction (SPME) procedure has been developed for the successful preconcentration of organic pollutant irradiated water. A SPME fused-silica fiber coated with Polyacrylate was used as a probe to extract the organic pollutant after irradiation. In this reference, degradation of priority organic pollutant methoxychlor (1, 1, 1-Trichloro 2, 2-bis (p-methoxyphenyl) ethane, in water by gamma irradiation under varied experimental conditions has been investigated. The degree of gamma radiolytic degradation was monitored by HPLC-UV and GC-MS. For 4 kGy and 5 kGy gamma radiation dose at a rate of 200 kGyh/sup -1/ greater or equal to 95 % and 98 % MXC was degraded respectively. The degradation products were identified by Mass Spectrometry after comparing their MS spectras with the NIST 98 library. The major degradation occurs via dechlorination, dehydro chlorination, by the detachment of methoxyphenyl from MXC and by interaction of other radicals generated by the water radiolysis. (author)

  11. Toxicological potential of 2-alkylcyclobutanones--specific radiolytic products in irradiated fat-containing food--in bacteria and human cell lines

    NARCIS (Netherlands)

    Hartwig, A; Pelzer, A; Burnouf, D; Titéca, H; Delincée, H; Briviba, K; Soika, C; Hodapp, C; Raul, F; Miesch, M; Werner, D; Horvatovich, P; Marchioni, E

    2007-01-01

    Food irradiation has been considered as a safe processing technology to improve food safety and preservation, eliminating efficiently bacterial pathogens, parasites and insects. This study aims to characterize the toxicological potential of 2-alkylcyclobutanones (2-ACBs), radiolytic derivatives of

  12. Introduction to Radcalc: A computer program to calculate the radiolytic production of hydrogen gas from radioactive wastes in packages

    International Nuclear Information System (INIS)

    Green, J.R.; Hillesland, K.E.; Field, J.G.

    1995-04-01

    A calculational technique for quantifying the concentration of hydrogen generated by radiolysis in sealed radioactive waste containers was developed in a U.S. Department of Energy (DOE) study conducted by EG ampersand G Idaho, Inc., and the Electric Power Research Institute (EPRI) TMI-2 Technology Transfer Office. The study resulted in report GEND-041, entitled open-quotes A Calculational Technique to Predict Combustible Gas Generation in Sealed Radioactive Waste Containersclose quotes. The study also resulted in a presentation to the U.S. Nuclear Regulatory Commission (NRC) which gained acceptance of the methodology for use in ensuring compliance with NRC IE Information Notice No. 84-72 (NRC 1984) concerning the generation of hydrogen within packages. NRC IE Information Notice No. 84-72: open-quotes Clarification of Conditions for Waste Shipments Subject to Hydrogen Gas Generationclose quotes applies to any package containing water and/or organic substances that could radiolytically generate combustible gases. EPRI developed a simple computer program in a spreadsheet format utilizing GEND-041 calculational methodology to predict hydrogen gas concentrations in low-level radioactive wastes containers termed Radcalc. The computer code was extensively benchmarked against TMI-2 (Three Mile Island) EPICOR II resin bed measurements. The benchmarking showed that the model developed predicted hydrogen gas concentrations within 20% of the measured concentrations. Radcalc for Windows was developed using the same calculational methodology. The code is written in Microsoft Visual C++ 2.0 and includes a Microsoft Windows compatible menu-driven front end. In addition to hydrogen gas concentration calculations, Radcalc for Windows also provides transportation and packaging information such as pressure buildup, total activity, decay heat, fissile activity, TRU activity, and transportation classifications

  13. Calculus of radiolytic products generation in water due to alpha radiation. Determination of the spent nuclear fuels matrix alteration rate Determination of velocity of spent fuel matrix; Calculo de la generacion de productos radioliticos en agua por radiacion {alpha}. Determinacion de la velocidad de alteracion de la matriz del combustible nuclear gastado

    Energy Technology Data Exchange (ETDEWEB)

    Quinones, J.; Serrano, J.; Diaz Arocas, P.; Rodriguez Almazan, J. L. [Ciemat. Madrid (Spain); Bruno, J.; Cera, E.; Merino, J.; Esteban, J. A.; Martinez-Esparza, A. [Enresa. Madrid (Spain)

    2000-07-01

    The generation of radiolytic products as a result of alpha radiation in the surface of the spent fuel is a key process in order to understand how the it becomes degraded in repository conditions. The present work has established a radiolytic model based on a set of reactions involving fuel oxidation-dissolution and radiolytic products recombination. It also includes the decrease of the dose rates as the main alpha emitters decay away. Four cases, with varying parameters of the system, have been assessed. The results show a decrease in both the concentration of the radiolytic products in the gap water and the degradation of the fuel matrix. It has been estimated that in the period of the evaluation (10''6 years) up to 52% of the pellet is altered in the conservative cases, whereas only 11% is altered in the realistic cases. No significant differences were observed when the carbonates reactions were included in the system. (Author)

  14. Radiolytic graphite oxidation revisited

    International Nuclear Information System (INIS)

    Minshall, P.C.; Sadler, I.A.; Wickham, A.J.

    1996-01-01

    The importance of radiolytic oxidation in graphite-moderated CO 2 -cooled reactors has long been recognised, especially in the Advanced Gas-Cooled Reactors where potential rates are higher because of the higher gas pressure and ratings than the earlier Magnox designs. In all such reactors, the rate of oxidation is partly inhibited by the CO produced in the reaction and, in the AGR, further reduced by the deliberate addition of CH 4 . Significant roles are also played by H 2 and H 2 O. This paper reviews briefly the mechanisms of these processes and the data on which they are based. However, operational experience has demonstrated that these basic principles are unsatisfactory in a number of respects. Gilsocarbon graphites produced by different manufacturers have demonstrated a significant difference in oxidation rate despite a similar specification and apparent equivalence in their pore size and distribution, considered to be the dominant influence on oxidation rate for a given coolant-gas composition. Separately, the inhibiting influence of CH 4 , which for many years had been considered to arise from the formation of a sacrificial deposit on the pore walls, cannot adequately be explained by the actual quantities of such deposits found in monitoring samples which frequently contain far less deposited carbon than do samples from Magnox reactors where the only source of such deposits is the CO. The paper also describes the current status of moderator weight-loss predictions for Magnox and AGR Moderators and the validation of the POGO and DIFFUSE6 codes respectively. 2 refs, 5 figs

  15. Concentration of stable elements in food products

    Energy Technology Data Exchange (ETDEWEB)

    Montford, M.A.; Shank, K.E.; Hendricks, C.; Oakes, T.W.

    1980-01-01

    Food samples were taken from commercial markets and analyzed for stable element content. The concentrations of most stable elements (Ag, Al, As, Au, Ba, Br, Ca, Ce, Cl, Co, Cr, Cs, Cu, Fe, Hf, I, K, La, Mg, Mn, Mo, Na, Rb, Sb, Sc, Se, Sr, Ta, Th, Ti, V, Zn, Zr) were determined using multiple-element neutron activation analysis, while the concentrations of other elements (Cd, Hg, Ni, Pb) were determined using atomic absorption. The relevance of the concentrations found are noted in relation to other literature values. An earlier study was extended to include the determination of the concentration of stable elements in home-grown products in the vicinity of the Oak Ridge National Laboratory. Comparisons between the commercial and local food-stuff values are discussed.

  16. Radiolytic degradation of the herbicide dicamba for environmental protection.

    Science.gov (United States)

    Drzewicz, P; Gehringer, P; Bojanowska-Czajka, A; Zona, R; Solar, S; Nałecz-Jawecki, G; Sawicki, J; Trojanowicz, M

    2005-04-01

    The radiolytic degradation of the widely used herbicide dicamba (3,6-dichloro-2-methoxybenzoic acid), employing gamma irradiation in laboratory batch conditions and with a beam of accelerated electrons in flow-through installation, was investigated. The effects of dose magnitude, ozone or hydrogen peroxide in irradiated solution, and scavengers such as nitrate and hydrogen carbonate on the effectiveness of dicamba decomposition and the products formed were investigated. Changes in the toxicity of irradiated solutions were measured with the Microtox and Spirotox toxicity tests. The application of radiolytic degradation was also examined for decomposition of herbicides in commercial agrochemical preparations.

  17. Radiolytic degradation of sorbic acid in isolated systems

    International Nuclear Information System (INIS)

    Thakur, B.R.; Trehan, I.R.; Arya, S.S.

    1990-01-01

    Effect of Co(60) gamma-irradiation on stability of sorbic acid (SA) in solutions, dough and chapaties has been investigated. SA was highly susceptible to radiolytic degradation in aqueous systems. Rate of degradation decreased with rise in pH. Sugars, hydrocolloids except pectin, citric acid, lactic acid, malic acid, arginine and threonine, catalyzed degradation while oxalic acid, maleic acid, Cu2+, nitrite, nitrate and phthalate had protective effects. SA was more stable in alcohols and vegetable oils than in aqueous solutions. In wheat flour radiolytic degradation of SA was less at lower moisture. Relatively SA was more stable in chapaties than in dough. Gelatinization and addition of oil in dough reduced degradation of SA

  18. The production of stable isotopes in Spain

    Energy Technology Data Exchange (ETDEWEB)

    Urgel, M.; Iglesias, J.; Casas, J.; Saviron, J. M.; Quintanilla, M.

    1965-07-01

    The activities developed in the field of the production of stable isotopes by means of ion-exchange chromatography and thermal diffusion techniques are reported. The first method was used to study the separation of the nitrogen and boron isotopes, whereby the separation factor was determined by the break through method. Values ranging from 1,028 to 1,022 were obtained for the separation factor of nitrogen by using ammonium hydroxide solutions while the corresponding values as obtained for boron amounted to 1,035-1,027 using boric acid solutions. Using ammonium chloride or acetate and sodium borate, respectively, resulted in the obtention of values for the separation factor approaching unity. The isotopic separation has been carried out according to the method of development by displacement. The separation of the isotopes of the noble gases, oxygen, nitrogen and carbon has been accomplished resorting to the method of thermal diffusion. (Author) 16 refs.

  19. The production of stable isotopes in Spain

    International Nuclear Information System (INIS)

    Urgel, M.; Iglesias, J.; Casas, J.; Saviron, J. M.; Quintanilla, M.

    1965-01-01

    The activities developed in the field of the production of stable isotopes by means of ion-exchange chromatography and thermal diffusion techniques are reported. The first method was used to study the separation of the nitrogen and boron isotopes, whereby the separation factor was determined by the break through method. Values ranging from 1,028 to 1,022 were obtained for the separation factor of nitrogen by using ammonium hydroxide solutions while the corresponding values as obtained for boron amounted to 1,035-1,027 using boric acid solutions. Using ammonium chloride or acetate and sodium borate, respectively, resulted in the obtention of values for the separation factor approaching unity. The isotopic separation has been carried out according to the method of development by displacement. The separation of the isotopes of the noble gases, oxygen, nitrogen and carbon has been accomplished resorting to the method of thermal diffusion. (Author) 16 refs

  20. Molecular metal clusters synthetized by a radiolytic process

    International Nuclear Information System (INIS)

    Remita, H.; Derai, R.; Delcourt, M.O.

    1991-01-01

    The radiolytic reduction of metal ions in alcohols has been achieved under CO atmosphere. Under such conditions, metal reduction, ligation and aggregation processes compete, leading to metal complexes and molecular clusters. These products are interesting for catalytic purposes. We report here the radiolytic synthesis of compounds of Fe, Ru, Os, Co, Ir, Rh, Pt, Cu, Ag, and of some intermetallic compounds. These synthesis are carried out under very mild temperature and pressure conditions (i.e., room temperature and at most I atmosphere of CO). Factors favoring a high nuclearity are the concentration, the high atomic number, a weak ligand/metal ratio. It is shown that chloride ions are inhibitors of complete reduction [fr

  1. Radiolytic degradation and stability of polycarbonate

    International Nuclear Information System (INIS)

    Araujo, E.S. de.

    1993-01-01

    The radiolytic stability of polycarbonate was studied using national commercial additives, employed in the photo and thermo-oxidative stabilization of polymers. Among several additives tested only two showed the efficiency to radiolytic protection: one quencher and one radical scavenger. It was derived a linear relation that provides by slope of the straight line the degree of degradation (scissions), G, and the factors of radiolytic protection P (degree of protection) and CE (capture of energy) conferred by radioprotector additive easily. Therefore the method developed in this work (viscosity) to study the molecular degradation and stability of polymers is a simply and precise method. The synergic mixture of two additives (1% of weight total) confers at polycarbonate excellent radiolytic protection of 98% (20 - 40 kGy) reducing the G value of 16.7 to only 0.4. (author). 69 refs, 31 figs, 17 tabs

  2. A model to estimate volume change due to radiolytic gas bubbles and thermal expansion in solution reactors

    International Nuclear Information System (INIS)

    Souto, F.J.; Heger, A.S.

    2001-01-01

    To investigate the effects of radiolytic gas bubbles and thermal expansion on the steady-state operation of solution reactors at the power level required for the production of medical isotopes, a calculational model has been developed. To validate this model, including its principal hypotheses, specific experiments at the Los Alamos National Laboratory SHEBA uranyl fluoride solution reactor were conducted. The following sections describe radiolytic gas generation in solution reactors, the equations to estimate the fuel solution volume change due to radiolytic gas bubbles and thermal expansion, the experiments conducted at SHEBA, and the comparison of experimental results and model calculations. (author)

  3. A model to estimate volume change due to radiolytic gas bubbles and thermal expansion in solution reactors

    Energy Technology Data Exchange (ETDEWEB)

    Souto, F.J. [NIS-6: Advanced Nuclear Technology, Los Alamos National Lab., Los Alamos, NM (United States); Heger, A.S. [ESA-EA: Engineering Sciences and Application, Los Alamos National Lab., Los Alamos, NM (United States)

    2001-07-01

    To investigate the effects of radiolytic gas bubbles and thermal expansion on the steady-state operation of solution reactors at the power level required for the production of medical isotopes, a calculational model has been developed. To validate this model, including its principal hypotheses, specific experiments at the Los Alamos National Laboratory SHEBA uranyl fluoride solution reactor were conducted. The following sections describe radiolytic gas generation in solution reactors, the equations to estimate the fuel solution volume change due to radiolytic gas bubbles and thermal expansion, the experiments conducted at SHEBA, and the comparison of experimental results and model calculations. (author)

  4. Indirect detection of radiation sources through direct detection of radiolysis products

    Science.gov (United States)

    Farmer, Joseph C [Tracy, CA; Fischer, Larry E [Los Gatos, CA; Felter, Thomas E [Livermore, CA

    2010-04-20

    A system for indirectly detecting a radiation source by directly detecting radiolytic products. The radiation source emits radiation and the radiation produces the radiolytic products. A fluid is positioned to receive the radiation from the radiation source. When the fluid is irradiated, radiolytic products are produced. By directly detecting the radiolytic products, the radiation source is detected.

  5. Radiolytic decomposition of environmental contaminants using an electron accelerator

    International Nuclear Information System (INIS)

    Matthews, S.M.; Boegel, A.J.; Caufield, R.A.; Jovanovich, M.C.; Loftis, J.A.

    1993-04-01

    Halogenated and nonhalogenated hydrocarbons are components of contamination currently found in natural waterways, ground water, and soils as a result of spills and careless disposal practices. The development of proper treatment methodologies for the waste streams producing this environmental damage is now a subject of growing concern. A significant number of these waste stream compounds are chemically stable and are thus resistant to environmental degradation. Numerous researchers have investigated the use of ionizing radiation to decompose chlorinated hydrocarbons in diverse matrices and have proposed various free-radical-induced reaction mechanisms. In this paper, we present results of experimentally measured radiolytically induced decomposition using accelerator-generated bremsstrahlung sources and gamma radiation from cobalt-60. Data are presented on the radiolytically induced reduction in concentration of volatile organic compounds (VOCs) dissolved in water and in air, polychlorinated biphenyl (PCB) dissolved in oil, high explosives dissolved in ground water, and chemical weapon surrogates. The results of these studies suggest the potential use of ionizing radiation as a method of hazardous waste treatment

  6. Development of stable isotope separation technology for radioisotope production

    International Nuclear Information System (INIS)

    Jeong, Do Young; Kim, Cheol Jung; Park, Kyung Bae

    2003-05-01

    The ultimate goal of this project is to construct the domestic production system of stable isotopes O-18 and Tl-203 used as target materials in accelerator for the production of medical radioisotopes F-18 and Tl-201, respectively. In order to achieve this goal, diode laser spectroscopic analytical system was constructed and automatic measurement computer software for the direct analysis of H 2 16 O/H 2 18 O ratio were developed. Distillation process, laser process, and membrane diffusion process were analyzed for the evaluation of O-18 production. And electromagnetic process, plasma process, and laser process were analyzed for the evaluation of Tl-203 production. UV laser system, IR laser system, and detailed system Tl-203 production were designed. Finally, current and future worldwide demand/supply of stable isotopes O-18 and Tl-203 were estimated

  7. Radiolytic degradation of malathion and lindane in aqueous solutions

    International Nuclear Information System (INIS)

    Mohamed, K.A.; Basfar, A.A.; Al-Kahtani, H.A.; Al-Hamad, K.S.

    2009-01-01

    Degradation of malathion and lindane pesticides present in an aqueous solution was investigated on a laboratory scale upon gamma-irradiation from a 60 Co source. The effects of pesticide group, presence of various additives and absorbed dose on efficiency of pesticide degradation were investigated. Gamma-irradiation was carried out in distilled water solutions (malathion and lindane) and in combination with humic solution (HS), nitrous oxide (N 2 O) and HS/N 2 O (lindane) over the range 0.1-2 kGy (malathion) and 5-30 kGy (lindane). Malathion was easily degraded at low absorbed doses compared to lindane in distilled water solutions. Absorbed doses required to remove 50% and 90% of initial malathion and lindane concentrations in distilled water solutions were 0.53 and 1.77 kGy (malathion) and 17.97 and 28.79 kGy (lindane), respectively. The presence of HS, N 2 O and HS/N 2 O additives in aqueous solutions, significantly improved the effectiveness of radiolytic degradation of lindane. Chemical analysis of the pesticides and the by-products resulted from the radiolytic degradation were made using a gas chromatography associated with mass spectrometry (GC-MS). Additionally, the final degradation products of irradiation as detected by ion chromatography (IC) were acetic acid and traces of some anions (phosphate and chloride).

  8. Production and use of stable isotopes in France

    International Nuclear Information System (INIS)

    Roth, E.; Letolle, R.

    1991-01-01

    This paper can not cover the field of production and use of stable isotopes in France exhaustively within six pages. We have chosen to concentrate on highlights of the subject and on recent work, and to give references for further reading. 26 refs

  9. Underestimation of hepatic glucose production by radioactive and stable tracers

    International Nuclear Information System (INIS)

    Argoud, G.M.; Schade, D.S.; Eaton, R.P.

    1987-01-01

    Although negative hepatic glucose production rates are physiologically impossible, they have been observed when hepatic glucose production is measured with the tracer-dilution technique during the hyperinsulinemic, euglycemic glucose clamp. Because hepatic glucose production is determined from the difference between tracer-derived glucose disposal and the known exogenous glucose infusion rate, the negative values for hepatic glucose production must result from an underestimation of glucose disposal by the tracer technique. In the current investigation, tracer-derived glucose disposal was measured in 25 subjects undergoing hyperinsulinemic, euglycemic clamps. Glucose disposal was measured with both radioactive and stable isotopes that utilize different methodologies, to determine whether discriminant metabolism of the isotopes versus methodological error leads to underestimation of tracer-derived glucose disposal. Both the radioactive and stable methodologies underestimated the exogenous glucose infusion rate during the hyperinsulinemic euglycemic clamp by 27 and 17%, respectively. Mean hepatic glucose production was -2.1 +/- 0.2 and -1.3 +/- 0.2 mg X kg-1 X min-1 as determined by the radioactive and stable isotope methodologies, respectively. Methodological error was an unlikely cause of this underestimation because it occurred with two different methodologies. The most likely explanation for underestimated rates of glucose disposal determined by the two types of isotope methodologies is discrepant metabolism of glucose tracers in comparison with unlabeled glucose

  10. Radiolytic decomposition of dioxins in liquid wastes

    International Nuclear Information System (INIS)

    Zhao Changli; Taguchi, M.; Hirota, K.; Takigami, M.; Kojima, T.

    2006-01-01

    The dioxins including polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are some of the most toxic persistent organic pollutants. These chemicals have widely contaminated the air, water, and soil. They would accumulate in the living body through the food chains, leading to a serious public health hazard. In the present study, radiolytic decomposition of dioxins has been investigated in liquid wastes, including organic waste and waste-water. Dioxin-containing organic wastes are commonly generated in nonane or toluene. However, it was found that high radiation doses are required to completely decompose dioxins in the two solvents. The decomposition was more efficient in ethanol than in nonane or toluene. The addition of ethanol to toluene or nonane could achieve >90% decomposition of dioxins at the dose of 100 kGy. Thus, dioxin-containing organic wastes can be treated as regular organic wastes after addition of ethanol and subsequent γ-ray irradiation. On the other hand, radiolytic decomposition of dioxins easily occurred in pure-water than in waste-water, because the reaction species is largely scavenged by the dominant organic materials in waste-water. Dechlorination was not a major reaction pathway for the radiolysis of dioxin in water. In addition, radiolytic mechanism and dechlorinated pathways in liquid wastes were also discussed. (authors)

  11. Development of Laser Application Technology for Stable Isotope Production

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Do Young; Ko, Kwang Hoon; Kwon, Duck Hee [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)] (and others)

    2007-04-15

    Tl-203 is used as a source material to produce Tl-201 radioisotope which is produced in a cyclotron by irradiating the enriched Tl-203 target. Tl-201 is a radiopharmaceutical for SPECT (single photon emission computerized tomography) to diagnose heart diseases and tumors. This Project aim to develop laser application technology to product stable isotopes such as Tl-203, Yb-168, and Yb-176. For this, photoion extraction device, atomic beam generator, dye lasers, and high power IR lasers are developed.

  12. Radiolytic and electron-transfer reactions in supercritical CO2

    International Nuclear Information System (INIS)

    Bartels, D. M.; Dimitrijevic, N. M.; Jonah, C. D.; Takahashi, K.

    2000-01-01

    Using supercritical fluids as solvents is useful for both practical and theoretical reasons. It has been proposed to use supercritical CO 2 as a solvent for synthesis because it eliminates the air pollution arising from other solvents. The properties of supercritical fluids can be easily varied with only modest changes in temperature and density, so they provide a way of testing theories of chemical reactions. It has also been proposed to use supercritical fluids for the treatment of hazardous mixed waste. For these reasons the authors have studied the production of radiolytic species in supercritical CO 2 and have measured their reactivity as a function of density. They have shown that the C 2 O 4 + is formed. They also have shown that the electron transfer reactions of dimethylaniline to C 2 O 4 + and CO 2 (e - ) to benzoquinone are diffusion controlled over a considerable density range

  13. Search for stable stau production at the LHC

    Energy Technology Data Exchange (ETDEWEB)

    Kaschube, Kolja

    2011-10-15

    In this thesis, a search for heavy stable charge particle production, in particular a quasistable supersymmetric tau lepton (''stau'') arising in gauge-mediated supersymmetry breaking (GMSB) models, is presented. This stable stau would cross detectors without decaying, resembling a muon, and produce signatures of high momentum or high ionization energy loss. The energy loss measurement represents a direct handle on the particle mass via the Bethe-Bloch formula. Proton-proton collisions at 7 TeV center-of-mass energy produced by the Large Hadron Collider and recorded by the CMS detector are investigated. Low-momentum collision data tracks are used to predict the background of highly ionizing tracks at high momenta. A high signal-to-background ratio is achieved by separating the search into channels with differing muon or stau multiplicities and by using the transverse momentum and energy loss measurement as the discriminating variables. Using 35.8 pb{sup -1} of data recorded in the 2010 LHC run, no excess is observed with respect to the expected Standard Model background. As a result, upper limits on the mass of stable status are derived within the context of the investigated GMSB models. (orig.)

  14. Search for stable stau production at the LHC

    International Nuclear Information System (INIS)

    Kaschube, Kolja

    2011-10-01

    In this thesis, a search for heavy stable charge particle production, in particular a quasistable supersymmetric tau lepton (''stau'') arising in gauge-mediated supersymmetry breaking (GMSB) models, is presented. This stable stau would cross detectors without decaying, resembling a muon, and produce signatures of high momentum or high ionization energy loss. The energy loss measurement represents a direct handle on the particle mass via the Bethe-Bloch formula. Proton-proton collisions at 7 TeV center-of-mass energy produced by the Large Hadron Collider and recorded by the CMS detector are investigated. Low-momentum collision data tracks are used to predict the background of highly ionizing tracks at high momenta. A high signal-to-background ratio is achieved by separating the search into channels with differing muon or stau multiplicities and by using the transverse momentum and energy loss measurement as the discriminating variables. Using 35.8 pb -1 of data recorded in the 2010 LHC run, no excess is observed with respect to the expected Standard Model background. As a result, upper limits on the mass of stable status are derived within the context of the investigated GMSB models. (orig.)

  15. Stable Isotope Systematics of Coalbed Gas during Desorption and Production

    Directory of Open Access Journals (Sweden)

    Martin Niemann

    2017-06-01

    Full Text Available The stable carbon isotope ratios of coalbed methane (CBM demonstrate diagnostic changes that systematically vary with production and desorption times. These shifts can provide decisive, predictive information on the behaviour and potential performance of CBM operations. Samples from producing CBM wells show a general depletion in 13C-methane with increasing production times and corresponding shifts in δ13C-CH4 up to 35.8‰. Samples from canister desorption experiments show mostly enrichment in 13C for methane with increasing desorption time and isotope shifts of up to 43.4‰. Also, 13C-depletion was observed in some samples with isotope shifts of up to 32.1‰. Overall, the magnitudes of the observed isotope shifts vary considerably between different sample sets, but also within samples from the same source. The δ13C-CH4 values do not have the anticipated signature of methane generated from coal. This indicates that secondary processes, including desorption and diffusion, can influence the values. It is also challenging to deconvolute these various secondary processes because their molecular and isotope effects can have similar directions and/or magnitudes. In some instances, significant alteration of CBM gases has to be considered as a combination of secondary alteration effects.

  16. Water content and porosity effect on hydrogen radiolytic yields of geopolymers

    Science.gov (United States)

    Chupin, Frédéric; Dannoux-Papin, Adeline; Ngono Ravache, Yvette; d'Espinose de Lacaillerie, Jean-Baptiste

    2017-10-01

    The behavior of geopolymers under irradiation is a topic that has not been thoroughly investigated so far. However, if geopolymers are considered to be used as radioactive waste embedding matrices, their chemical and mechanical stability under ionizing radiation as well as low hydrogen production must be demonstrated. For that purpose, a particular focus is put on water radiolysis. Various formulations of geopolymers have been irradiated either with γ-rays (60Co source) or 95 MeV/amu 36Ar18+ ions beams and the hydrogen production has been quantified. This paper presents the results of radiolytic gas analysis in order to identify important structural parameters that influence confined water radiolysis. A correlation between geopolymers nature, water content on the one side, and the hydrogen radiolytic yield (G(H2)) on the other side, has been demonstrated. For both types of irradiations, a strong influence of the water content on the hydrogen radiolytic yield G(H2) is evidenced. The geopolymers porosity effect has been only highlighted under γ-rays irradiation.

  17. Modelling the radiolytic corrosion of α-doped UO2 and spent nuclear fuel

    Science.gov (United States)

    Liu, Nazhen; Qin, Zack; Noël, James J.; Shoesmith, David W.

    2017-10-01

    A model previously developed to predict the corrosion rate of spent fuel (UO2) inside a failed waste container has been adapted to simulate the rates measured on a wide range of α-doped UO2 and spent fuel specimens. This simulation confirms the validity of the model and demonstrates that the steady-state corrosion rate is controlled by the radiolytic production of H2O2 (which has been shown to be the primary oxidant driving fuel corrosion), irrespective of the reactivity of the UO2 matrix. The model was then used to determine the consequences of corrosion inside a failed container resealed by steel corrosion products. The possible accumulation of O2, produced by H2O2 decomposition, was found to accelerate the corrosion rate in a closed system. However, the simultaneous accumulation of radiolytic H2, which is activated as a reductant on the noble metal (ε) particles in the spent fuel, rapidly overcame this acceleration leading to the eventual suppression of the corrosion rate to insignificant values. Calculations also showed that, while the radiation dose rate, the H2O2 decomposition ratio, and the surface coverage of ε particles all influenced the short term corrosion rate, the influence of the radiolytically produced H2 was the overwhelming influence in reducing the rate to negligible level (i.e., <10-20 mol m-2 s-1).

  18. Production of stable isotopes utilizing the plasma separation process

    Science.gov (United States)

    Bigelow, T. S.; Tarallo, F. J.; Stevenson, N. R.

    2005-12-01

    A plasma separation process (PSP) is being operated at Theragenics Corporation's®, Oak Ridge, TN, facility for the enrichment of stable isotopes. The PSP utilizes ion cyclotron mass discrimination to separate isotopes on a relatively large scale. With a few exceptions, nearly any metallic element could be processed with PSP. Output isotope enrichment factor depends on natural abundance and mass separation and can be fairly high in some cases. The Theragenics™ PSP facility is believed to be the only such process currently in operation. This system was developed and formerly operated under the US Department of Energy Advanced Isotope Separation program. Theragenics™ also has a laboratory at the PSP site capable of harvesting the isotopes from the process and a mass spectrometer system for analyzing enrichment and product purity. Since becoming operational in 2002, Theragenics™ has utilized the PSP to separate isotopes of several elements including: dysprosium, erbium, gadolinium, molybdenum and nickel. Currently, Theragenics™ is using the PSP for the separation of 102Pd, which is used as precursor for the production of 103Pd. The 103Pd radioisotope is the active ingredient in TheraSeed®, which is used in the treatment of early stage prostate cancer and being investigated for other medical applications. New industrial, medical and research applications are being investigated for isotopes that can be enriched on the PSP. Pre-enrichment of accelerator or reactor targets offers improved radioisotope production. Theragenics operates 14 cyclotrons for proton activation and has access to HFIR at ORNL for neutron activation of radioisotopes.

  19. Contribution to the study of degradation products of spent fuel reprocessing solvents using mass spectroscopy, its different linkages and by the use of stable isotopes

    International Nuclear Information System (INIS)

    Lesage, Denis

    1995-01-01

    Tributylphosphate (TBP) is used as an extraction solvent in nuclear fuel reprocessing. The presence of uranium fission products leads to the formation of a large variety of organic compounds resulting from radiolytic degradation of TBP. Some of these compounds can complex metallic cations, and as a result, to decrease nuclear fuel extraction yields. In this work we have studied by tandem mass spectrometry the fragmentation mechanisms of different TBP and their dimers. These molecules are interesting because of the similarity of their structures to other more complex molecules formed by irradiation (functionalized TBP and TBP dimers). This work allowed to identify mixtures of degradation products and relate their structures to radiolytic mechanisms. Ail these results, including structure determination and formation mechanisms, have been validated by using specifically labeled compounds (deuterium, oxygen 18, nitrogen 15). (author) [fr

  20. Production of stable isotopes at Urenco. 10 years of progress

    International Nuclear Information System (INIS)

    Mol, C.A.; Rakhorst, H.

    2003-01-01

    In the last ten years, Urenco has built its spin-off activity of stable isotopes in a multi-million dollar business. It is a high quality, ISO certified, client oriented and profitable European business with further growth potential. (author)

  1. Observation of Radiolytic Field Alteration of the Uranyl Cation in Bicarbonate Solution

    Energy Technology Data Exchange (ETDEWEB)

    Snow, Lanee A.; McNamara, Bruce K.; Sinkov, Sergey I.; Cho, Herman M.; Friese, Judah I.

    2006-12-01

    In previous work we demonstrated that radiolysis of uranyl tris carbonate in near neutral pH to alkaline carbonate solutions, could be followed by 13C NMR. Radiolysis of the complex produced novel uranyl peroxo carbonate solution state species, whose structures depended on the pH and radiolytic dose rate. In this work, we investigate speciation of the uranyl carbonate trimer which is predominant in bicarbonate solution near pH 5.9. We observe radiolytically derived speciation to different mixed peroxy carbonate species than seen in the higher pH solutions. Auto radiolysis of uranium (VI) carbonate solutions between pH 5.9 and 7.2 is shown to alter the uranium speciation over relatively short periods of time and was followed by 13C NMR and visible spectrophotometry, using dissolved 233(UO2)3(CO3)6 6- both as the radiolysis source (D= 14.9 Gy/hr) and as a trap for the newly formed hydrogen peroxide. Direct addition of hydrogen peroxide to solutions of the uranyl-carbonate trimer is shown to reproduce the 13 C NMR signatures of the complexe(s) formed by radiolysis, but additionally a variety of new complexes are revealed. Ratios of H2O2/trimer < 1.5 produced a uranyl peroxo carbonate adduct, that is shown to be common to the radiolytically produced species. Ratios of H2O2/ trimer >1 resulted in formation of stable higher order peroxo carbonate complexes. The 13C NMR signatures and visible spectra of these complexes are described here. Rigorous characterization of the species is an ongoing effort.

  2. Statistical optimization of thermo-alkali stable xylanase production from Bacillus tequilensis strain ARMATI

    Directory of Open Access Journals (Sweden)

    Ameer Khusro

    2016-07-01

    Conclusions: The cellulase-free xylanase showed an alkali-tolerant and thermo-stable property with potentially applicable nature at industrial scale. This statistical approach established a major contribution in enzyme production from the isolate by optimizing independent factors and represents a first reference on the enhanced production of thermo-alkali stable cellulase-free xylanase from B. tequilensis.

  3. Possibilities for the production of non-stable isotopes

    International Nuclear Information System (INIS)

    Benlliure, J.; Enqvist, T.; Junghans, A.R.; Ricciardi, V.; Schmidt, K.H.; Farget, F.

    1999-04-01

    The production of neutron-rich isotopes is discussed in terms of the two main reaction mechanisms leading to the formation of these nuclei, projectile fragmentation and fission. Production cross sections are calculated for cold-fragmentation and fission. The expected yields are estimated taking into account different technical approaches actually discussed for the production of radioactive beams. (orig.)

  4. Radiolytic and thermal generation of gases from Hanford grout samples

    Energy Technology Data Exchange (ETDEWEB)

    Meisel, D.; Jonah, C.D.; Kapoor, S.; Matheson, M.S.; Mulac, W.A.

    1993-10-01

    Gamma irradiation of WHC-supplied samples of grouted Tank 102-AP simulated nonradioactive waste has been carried out at three dose rates, 0.25, 0.63, and 130 krad/hr. The low dose rate corresponds to that in the actual grout vaults; with the high dose rate, doses equivalent to more than 40 years in the grout vault were achieved. An average G(H{sub 2}) = 0.047 molecules/100 eV was found, independent of dose rate. The rate of H2 production decreases above 80 Mrad. For other gases, G(N{sub 2}) = 0.12, G(O{sub 2}) = 0.026, G(N{sub 2}O) = 0.011 and G(CO) = 0.0042 at 130 krad/hr were determined. At lower dose rates, N{sub 2} and O{sub 2} could not be measured because of interference by trapped air. The value of G(H{sub 2}) is higher than expected, suggesting segregation of water from nitrate and nitrite salts in the grout. The total pressure generated by the radiolysis at 130 krad/h has been independently measured, and total amounts of gases generated were calculated from this measurement. Good agreement between this measurement and the sum of all the gases that were independently determined was obtained. Therefore, the individual gas measurements account for most of the major components that are generated by the radiolysis. At 90 {degree}C, H{sub 2}, N{sub 2}, and N{sub 2}O were generated at a rate that could be described by exponential formation of each of the gases. Gases measured at the lower temperatures were probably residual trapped gases. An as yet unknown product interfered with oxygen determinations at temperatures above ambient. The thermal results do not affect the radiolytic findings.

  5. Investigation of the hydrolytic and radiolytic degradation of HEH[EHP

    Energy Technology Data Exchange (ETDEWEB)

    Peterman, Dean Richard [Idaho National Lab. (INL), Idaho Falls, ID (United States); McDowell, Rocklan George [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zarzana, Christopher Andrew [Idaho National Lab. (INL), Idaho Falls, ID (United States); Johnson, Kristyn Marie [Idaho National Lab. (INL), Idaho Falls, ID (United States); Rowe, Salene Marie [Idaho National Lab. (INL), Idaho Falls, ID (United States); Groenewold, Gary Steven [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-03-01

    The extractant 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (HEH[EHP]) is a component used in both the Advanced TALSPEAK and ALSEP solvent extraction processes. The most likely compound formed via hydrolytic or radiolytic degradation of HEH[EHP] would be the phosphonic acid 2-ethylhexylphosphonic acid (H2EHP) that is formed by cleavage of the P-O-R bond. Thus far, attempts to detect H2EHP by gas chromatography or mass spectrometry have not been successful. The inability to detect this proposed degradation product in analytical samples is likely due to inadequate analysis techniques, lack of H2EHP production, further decomposition of H2EHP forming products not detectable by the employed analytical techniques, or a combination of all of the above scenarios. In order to address this problem, commercially available alkylphosphonic acids were acquired and used as surrogates for H2EHP in the gas chromatography and mass spectrometry analysis of samples. Once the ability to detect alkylphosphonic acid compounds was confirmed, these analytical techniques were used to confirm the production of H2EHP in samples of HEH[EHP] exposed to nitric acid and nitric acid plus gamma radiation. This report provides a brief summary of results and serves as documentation of the completion the level four milestone M4FT-16IN030102025 “Investigate the hydrolytic and radiolytic degradation of HEH[EHP]”.

  6. Technology for production of shelf stable fruit cubes

    International Nuclear Information System (INIS)

    Mishra, B.B.; Jain, M.P.; Sharma, A.

    2009-01-01

    A technology has been developed for the production of intermediate moisture fruit cubes using a combination of osmotic dehydration and infrared drying. Fruits like pineapple, papaya, mango, banana and apple can be successfully converted into intermediate moisture products in the form of fruit cubes using this technology. The fruit cubes can blend very well as natural nutritious supplements with breakfast cereals and in certain food preparations like ice creams, milk shakes, jellies and custards. The product is microbiologically safe for consumption and can be stored at ambient storage condition for more than six months. This technology is an effective alternative for post harvest processing and preservation of ripened fruits. Fruit jam is an additional by-product generated by the process. This technology has been transferred to TT and CD, BARC

  7. Shelf-stable egg-based products processed by high pressure thermal sterilization

    Science.gov (United States)

    Producing a thermally sterilized egg-based product with increased shelf life without losing the sensory and nutritional properties of the freshly prepared product is challenging. Until recently, all commercial shelf-stable egg-based products were sterilized using conventional thermal processing; how...

  8. Physicochemical properties and radiolytic degradation studies on tri-iso-amyl phosphate (TiAP)

    Energy Technology Data Exchange (ETDEWEB)

    Sreenivasulu, B.; Sivaraman, Nagarajan [Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India). Homi Bhabha National Inst.; Suresh, A.; Rajeswari, S.; Ramanathan, N.; Antony, M.P.; Joseph, M. [Indira Gandhi Centre for Atomic Research, Kalpakkam, Tamil Nadu (India). Chemistry Group

    2017-06-01

    The solvent composed of tri-iso-amyl phosphate (TiAP) in n-dodecane (n-DD) is regarded as a promising candidate for reprocessing of spent fuel. In this context, the radiolytic degradation of a solution of TiAP in n-dodecane was investigated by irradiating the solvent to various absorbed dose levels of γ-radiation. The neat extractant or a solution of extractant in n-dodecane was irradiated in the presence of nitric acid. Physicochemical properties such as density, viscosity and interfacial tension (IFT) were measured for unirradiated and irradiated solutions. The extent of degradation was determined by measuring the variation in extraction behavior of U(VI) and Pu(IV) with irradiated solvent systems. Uranium and plutonium retention with irradiated solvents was also measured. The distribution ratio of uranium and plutonium increased with increase in absorbed dose. Effect of alpha degradation was studied by plutonium retention as a function of time using 1.1 M TiAP/n-DD. Laser desorption/ionization mass spectrometric technique was employed to identify the possible radiolytic degradation products. Similar studies were also carried out with tri-n-butyl phosphate (TBP) based solvent system under identical experimental conditions and the results are compared.

  9. Authentication of fishery and aquaculture products by multi-element and stable isotope analysis.

    Science.gov (United States)

    Li, Li; Boyd, Claude E; Sun, Zhenlong

    2016-03-01

    The market of fishery and aquaculture products is globalized with increasing numbers of mislabeled products. This highlights the need for approaches to indentify the origin of these products. Among the measures used to identify the origin of other agro-products, multi-element and stable isotope analysis are promising approaches to identify the authenticity and traceability of fishery and aquaculture products. The present paper reviews the use of multi-element and stable isotope analysis to determine the origin of fishery and aquaculture products. Principles and limitations of each method will be illustrated and perspectives for traceability of fishery and aquaculture products will be discussed. The aim of this review is to mediate fundamental knowledge for the interpretation of experimental data on authentication of aquaculture products. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Progresses in the stable isotope studies of microbial processes associated with wetland methane production

    International Nuclear Information System (INIS)

    Li Qing; Lin Guanghui

    2013-01-01

    Methane emissions from wetlands play a key role in regulating global atmospheric methane concentration, so better understanding of microbial processes for the methane emission in wetlands is critical for developing process models and reducing uncertainty in global methane emission inventory. In this review, we describe basic microbial processes for wetland methane production and then demonstrate how stable isotope fractionation and stable isotope probing can be used to investigate the mechanisms underlying different methanogenic pathways and to quantify microbial species involved in wetland methane production. When applying stable isotope technique to calculate contributions of different pathways to the total methane production in various wetlands, the technical challenge is how to determine isotopic fractionation factors for the acetate derived methane production and carbon dioxide derived methane production. Although the application of stable isotope probing techniques to study the actual functions of different microbial organisms to methane production process is significantly superior to the traditional molecular biology method, the combination of these two technologies will be crucial for direct linking of the microbial community and functional structure with the corresponding metabolic functions, and provide new ideas for future studies. (authors)

  11. Latest developments at GANIL for stable and radioactive ion beam production

    International Nuclear Information System (INIS)

    Jardin, P.; Barue, C.; Bajeat, O.; Canet, C.; Clement, E.; Cornell, J. C.; Delahaye, P.; Dubois, M.; Dupuis, M.; Flambard, J. L.; Fraanberg, H.; Frigot, R.; Leboucher, C.; Lecesne, N.; Lecomte, P.; Leherissier, P.; Lemagnen, F.; Leroy, R.; Maunoury, L.; Mery, A.

    2010-01-01

    In the frame of the SPIRAL II (Systeme de Production d'Ions Radioactifs Acceleres en Ligne Partie II) project, several developments of stable and radioactive ion production systems have been started up. In parallel, GANIL has the ambition to preserve the existing stable and radioactive beams and also to increase its range by offering new ones. In order to identify the best directions for this development, a new group called GANISOL has been formed. Its preliminary conclusions and the latest developments at GANIL are presented.

  12. Recent developments in application of stable isotope analysis on agro-product authenticity and traceability.

    Science.gov (United States)

    Zhao, Yan; Zhang, Bin; Chen, Gang; Chen, Ailiang; Yang, Shuming; Ye, Zhihua

    2014-02-15

    With the globalisation of agro-product markets and convenient transportation of food across countries and continents, the potential for distribution of mis-labelled products increases accordingly, highlighting the need for measures to identify the origin of food. High quality food with identified geographic origin is a concern not only for consumers, but also for agriculture farmers, retailers and administrative authorities. Currently, stable isotope ratio analysis in combination with other chemical methods gradually becomes a promising approach for agro-product authenticity and traceability. In the last five years, a growing number of research papers have been published on tracing agro-products by stable isotope ratio analysis and techniques combining with other instruments. In these reports, the global variety of stable isotope compositions has been investigated, including light elements such as C, N, H, O and S, and heavy isotopes variation such as Sr and B. Several factors also have been considered, including the latitude, altitude, evaporation and climate conditions. In the present paper, an overview is provided on the authenticity and traceability of the agro-products from both animal and plant sources by stable isotope ratio analysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. Radiolytic stabilization on optical properties of polycarbonate

    International Nuclear Information System (INIS)

    Ferreira, Carlas P.R.C.; Araujo, Elmo S.; Aquino, Katia A.S.

    2011-01-01

    Polycarbonate (PC) is an engineering plastic widely used in several industrial segments. However, in medical applications, this material is required to be sterilized by ionizing radiation in doses of 25kGy. PC, when gamma irradiated, undergoes main chain scissions with consequent formation of phenoxy and phenyl radicals. The former remains trapped into the polymer matrix causing undesirable yellowness on material at room temperature. A strategy to minimize such effect is to incorporate additives into the polymer system enabling efficient phenoxy radicals and secondary electrons scavenging. Our results show that, in absorbed dose of 25kGy, change in yellowness index (ΔΥI) decreases from 15.6 to 3.9 for PC containing 0.8% of additives. The color differences (ΔE *) between the non-irradiated sample and that irradiated at 25kGy were 2.4 and 9.8, for PC with additive and PC control, respectively. Mechanical properties of gamma-irradiated PC were also evaluated and showed no significant change, even without stabilizing additives. Thus, this work establishes a new PC formulation stable to gamma irradiation at sterilizing absorbed doses. (author)

  14. Radiolytic decomposition of water-ethanol mixtures

    International Nuclear Information System (INIS)

    Baquey, Charles

    1968-07-01

    This research thesis addresses the study of the behaviour of binary mixtures submitted to ionizing radiations, and notably aims, by studying the case of water-ethanol mixtures, at verifying solutions proposed by previously published works on the origin of hydrogen atoms and of molecular hydrogen, on the intervention of excited atoms, and on the origin of products appearing under radiolysis. The experimental part of this work consists in the dosing of products formed in water-ethanol mixtures irradiated in presence or absence of nitrate, hydrogen, hydrocarbon, acetaldehyde, 2-3 butanediol and nitrite. Results are discussed and interpreted in terms of acetaldehyde efficiency, 2-3 butanediol efficiencies, and hydrocarbon efficiencies in pure ethanol, and in water-ethanol mixtures. The influence of the presence of nitrate ions in mixtures is also discussed

  15. Combined strategies for improving production of a thermo-alkali stable laccase in Pichia pastoris

    Directory of Open Access Journals (Sweden)

    Jiayi Wang

    2017-07-01

    Conclusions: The productivity of the thermo-alkali stable laccase from B. licheniformis expressed in P. pastoris was significantly improved through the combination of site-directed mutagenesis and optimization of the cultivation process. The mutant enzyme retains good stability under high temperature and alkaline conditions, and is a good candidate for industrial application in dye decolorization.

  16. Development of shelf stable, processed, low acid food products using heat-irradiation combination treatments

    International Nuclear Information System (INIS)

    Minnaar, A.

    1998-01-01

    The amount of ionizing irradiation needed to sterilize low acid vegetable and starch products (with and without sauces) commercially impairs their sensorial and nutritive qualities, and use of thermal processes for the same purpose may also have an adverse effect on the product quality. A systematic approach to the establishment of optimized combination parameters was developed for heat-irradiation processing to produce high quality, shelf stable, low acid food products. The effects of selected heat, heat-irradiation combination and irradiation treatments on the quality of shelf stable mushrooms in brine and rice, stored at ambient temperature, were studied. From a quality viewpoint, use of heat-irradiation combination treatments favouring low irradiation dose levels offered a feasible alternative to thermally processed or radappertized mushrooms in brine. However, shelf stable rice produced by heat-irradiation combination treatments offered a feasible alternative only to radappertized rice from the standpoint of quality. The technical requirements for the heat and irradiation processing of a long grain rice cultivar from the United States of America oppose each other directly, thereby reducing the feasibility of using heat-irradiation combination processing to produce shelf stable rice. The stability of starch thickened white sauces was found to be affected severely during high dose irradiation and subsequent storage at ambient temperature. However, use of pea protein isolate as a thickener in white sauces was found to have the potential to maintain the viscosity of sauces for irradiated meat and sauce products throughout processing and storage. (author)

  17. Unusual radiolytic behavior of neptunium ions in aqueous bicarbonate solutions

    International Nuclear Information System (INIS)

    Shilov, V.P.; Gogolev, A.V.; Pikaev, A.K.

    2000-01-01

    Behavior of neptunium ions in carbonate and bicarbonate aqueous solutions saturated with air, oxygen or argon during gamma radiation ( 60 Co) by doses up to 3 kGy at dose rates 10 and 25 Gy/min was studied by the method of spectrophotometry. It is shown that in neptunium (5) bicarbonate solution nearly complete (95%) neptunium ion oxidation occurs under the effect of radiation, whereas no oxidation is observed in carbonate solution. Radiation-chemical yield of neptunium (5) oxidation and stationary concentration of neptunium (6) ions depend on concentration of bicarbonate-ions. Explanation to the results obtained is made from the viewpoint of potential radiolytic reactions [ru

  18. Sulfuric acid on Europa and the radiolytic sulfur cycle

    Science.gov (United States)

    Carlson, R. W.; Johnson, R. E.; Anderson, M. S.

    1999-01-01

    A comparison of laboratory spectra with Galileo data indicates that hydrated sulfuric acid is present and is a major component of Europa's surface. In addition, this moon's visually dark surface material, which spatially correlates with the sulfuric acid concentration, is identified as radiolytically altered sulfur polymers. Radiolysis of the surface by magnetospheric plasma bombardment continuously cycles sulfur between three forms: sulfuric acid, sulfur dioxide, and sulfur polymers, with sulfuric acid being about 50 times as abundant as the other forms. Enhanced sulfuric acid concentrations are found in Europa's geologically young terrains, suggesting that low-temperature, liquid sulfuric acid may influence geological processes.

  19. Radiolytic Syntheses of Nanoparticles and Inorganic-Polymer Hybrid Microgels

    International Nuclear Information System (INIS)

    Chen, Q.; Shi, J.; Zhao, R.; Shen, X.

    2010-01-01

    In the second year of the project, we have gotten progress mainly in two directions. Firstly, for the first time, Prussian blue (PB) nanoparticles (NPs) were successfully synthesized by the partly radiolytic reduction of Fe3+ and Fe(CN)63 in the presence of poly(N-vinyl pyrrolidine) (PVP) under N2 atmospheres at room temperature. With the increase of the concentration of PVP, the size and the size distribution of the synthesized quasi-spherical PB NPs decreased obviously, leading to a hypsochromic shift on their peak position of the characteristic absorption. In the experiment, we further found that the smaller ones have a larger capacity to Cs+, suggesting that the application of PB NPs in curing thallotoxicosis may decrease the usage of PB for the patient to great extent. Secondly, through a series of preliminary experiments, we got a clear picture about the one-step radiolytic preparation of inorganic-poly(methacrylic acid-co-methyl methacrylate) hybrid microgels by surfactant-free emulsion polymerization. Besides, unpurified N-carbamothioylmethacrylamide was synthesized via the methacrylation of thiourea. These created favorable conditions for the one-step synthesis of metal sulfide-poly(methacrylic acid-co-methyl methacrylate) hybrid microgels by -irradiation and surfactant-free emulsion polymerization. (author)

  20. Radiolytic reactions in the coolant of helium cooled reactors

    International Nuclear Information System (INIS)

    Tingey, G.L.; Morgan, W.C.

    1975-01-01

    The success of helium cooled reactors is dependent upon the ability to prevent significant reaction between the coolant and the other components in the reactor primary circuit. Since the thermal reaction of graphite with oxidizing gases is rapid at temperatures of interest, the thermal reactions are limited primarily by the concentration of impurity gases in the helium coolant. On the other hand, the rates of radiolytic reactions in helium are shown to be independent of reactive gas concentration until that concentration reaches a very low level. Calculated steady-state concentrations of reactive species in the reactor coolant and core burnoff rates are presented for current U. S. designed, helium cooled reactors. Since precise base data are not currently available for radiolytic rates of some reactions and thermal reaction rate data are often variable, the accuracy of the predicted gas composition is being compared with the actual gas compositions measured during startup tests of the Fort Saint Vrain high temperature gas-cooled reactor. The current status of these confirmatory tests is discussed. 12 references

  1. Radiolytic stabilization of industrial poly(methyl methacrylate)

    International Nuclear Information System (INIS)

    Aquino, Katia Aparecida da Silva

    2005-03-01

    Poly(methyl methacrylate), PMMA, Acrigel, a Brazilian polymer, is used in the manufacture of medical supplies sterilisable by ionizing radiation. However, when PMMA is gamma-irradiated it undergoes main chain scissions, which promote molecular degradation causing reduction in its physical properties. Therefore, radiolytic stabilization of PMMA is important for to become it commercially radio sterilisable. In this work we investigated the radiolytic stabilization of PMMA by using HALS (Hindered Amine Light Stabilizer) additive, commercially used for photo and thermo oxidative stabilization of polymers. The investigation of the radiation-induced main chain scissions was carried out by viscometric method. The additive added to the polymer system at 0.3 % w/w promotes a molecular radioprotection of 61%. That means a reduction of G value (scissions/100 eV) from 2.6 to 1.0. In addition, the glassy transition temperature (Tg) of PMMA (no additive), significantly changed by radiation, does not change when PMMA (with additive) is irradiated. TGA analysis showed that the additive promotes thermal stability to the system, increasing decomposition temperature of PMMA. Spectroscopy analysis, FT-IR and RMN ( 1 H), showed that the radioprotector additive added to the system does not change the PMMA structure. Analysis on mechanical (tensile strength and elongation at break) and optical (yellowness index and refractive index) properties showed a good influence of the additive on polymer system. (author)

  2. Concerted effects in the reaction of ·OH radicals with aromatics: radiolytic oxidation of salicylic acid

    International Nuclear Information System (INIS)

    Albarran, G.; Schuler, R.H.

    2003-01-01

    Liquid chromatographic and capillary electrophoretic studies have been used to resolve the products produced in the radiolytic oxidation of salicylic acid in aqueous solution. These studies have shown that, as in the case of phenol, · OH radicals preferentially add to the positions ortho and para to the OH substituent. However, in contrast to its reaction with phenol, addition at the ortho position is favored over addition at the para position. Because · OH radical is a strong electrophile this difference suggests that the electron population at the ortho position in the salicylate anion is enhanced as a result of the hydrogen bonding in salicylic acid

  3. Perioperative plasma concentrations of stable nitric oxide products are predictive of cognitive dysfunction after laparoscopic cholecystectomy.

    LENUS (Irish Health Repository)

    Iohom, G

    2012-02-03

    In this study our objectives were to determine the incidence of postoperative cognitive dysfunction (POCD) after laparoscopic cholecystectomy under sevoflurane anesthesia in patients aged >40 and <85 yr and to examine the associations between plasma concentrations of i) S-100beta protein and ii) stable nitric oxide (NO) products and POCD in this clinical setting. Neuropsychological tests were performed on 42 ASA physical status I-II patients the day before, and 4 days and 6 wk after surgery. Patient spouses (n = 13) were studied as controls. Cognitive dysfunction was defined as deficit in one or more cognitive domain(s). Serial measurements of serum concentrations of S-100beta protein and plasma concentrations of stable NO products (nitrate\\/nitrite, NOx) were performed perioperatively. Four days after surgery, new cognitive deficit was present in 16 (40%) patients and in 1 (7%) control subject (P = 0.01). Six weeks postoperatively, new cognitive deficit was present in 21 (53%) patients and 3 (23%) control subjects (P = 0.03). Compared with the "no deficit" group, patients who demonstrated a new cognitive deficit 4 days postoperatively had larger plasma NOx at each perioperative time point (P < 0.05 for each time point). Serum S-100beta protein concentrations were similar in the 2 groups. In conclusion, preoperative (and postoperative) plasma concentrations of stable NO products (but not S-100beta) are associated with early POCD. The former represents a potential biochemical predictor of POCD.

  4. Possibility of hypothetical stable micro black hole production at future 100 TeV collider

    Energy Technology Data Exchange (ETDEWEB)

    Sokolov, A.V. [Institute for Nuclear Research of the Russian Academy of Sciences, Moscow (Russian Federation); Lomonosov Moscow State University, Physics Department, Moscow (Russian Federation); Institute of Theoretical and Experimental Physics, Moscow (Russian Federation); Pshirkov, M.S. [Institute for Nuclear Research of the Russian Academy of Sciences, Moscow (Russian Federation); Lomonosov Moscow State University, Sternberg Astronomical Institute, Moscow (Russian Federation); Pushchino Radio Astronomy Observatory, P.N. Lebedev Physical Institute, Pushchino (Russian Federation)

    2017-12-15

    We study the phenomenology of TeV-scale black holes predicted in theories with large extra dimensions, under the further assumption that they are absolutely stable. Our goal is to present an exhaustive analysis of safety of the proposed 100 TeV collider, as it was done in the case of the LHC. We consider the theories with different number of extra dimensions and identify those for which a possible accretion to macroscopic size would have timescales shorter than the lifetime of the Solar system. We calculate the cross sections of the black hole production at the proposed 100 TeV collider, the fraction of the black holes trapped inside the Earth and the resulting rate of capture inside the Earth via an improved method. We study the astrophysical consequences of stable micro black holes existence, in particular its influence on the stability of white dwarfs and neutron stars. We obtain constraints for the previously unexplored range of higher-dimensional Planck mass values. Several astrophysical scenarios of the micro black hole production, which were not considered before, are taken into account. Finally, using the astrophysical constraints we consider the implications for future 100 TeV terrestrial experiments. We exclude the possibility of the charged stable micro black holes production. (orig.)

  5. Review of the microbiological, chemical and radiolytic degradation of organic material likely to be present in intermediate level and low level radioactive wastes

    International Nuclear Information System (INIS)

    Greenfield, B.F.; Rosevear, A.; Williams, S.J.

    1990-11-01

    A review has been made of the microbiological, chemical and radiolytic degradation of the solid organic materials likely to be present in intermediate-level and low-level radioactive wastes. Possible interactions between the three routes for degradation are also discussed. Attention is focussed on the generation of water-soluble degradation products which may form complexes with radioelements. The effects of complexation on radioelement solubility and sorption are considered. Recommendations are made for areas of further research. (author)

  6. Principles and limitations of stable isotopes in differentiating organic and conventional foodstuffs: 2. Animal products.

    Science.gov (United States)

    Inácio, Caio T; Chalk, Phillip M

    2017-01-02

    In this review, we examine the variation in stable isotope signatures of the lighter elements (δ 2 H, δ 13 C, δ 15 N, δ 18 O, and δ 34 S) of tissues and excreta of domesticated animals, the factors affecting the isotopic composition of animal tissues, and whether stable isotopes may be used to differentiate organic and conventional modes of animal husbandry. The main factors affecting the δ 13 C signatures of livestock are the C3/C4 composition of the diet, the relative digestibility of the diet components, metabolic turnover, tissue and compound specificity, growth rate, and animal age. δ 15 N signatures of sheep and cattle products have been related mainly to diet signatures, which are quite variable among farms and between years. Although few data exist, a minor influence in δ 15 N signatures of animal products was attributed to N losses at the farm level, whereas stocking rate showed divergent findings. Correlations between mode of production and δ 2 H and δ 18 O have not been established, and only in one case of an animal product was δ 34 S a satisfactory marker for mode of production. While many data exist on diet-tissue isotopic discrimination values among domesticated animals, there is a paucity of data that allow a direct and statistically verifiable comparison of the differences in the isotopic signatures of organically and conventionally grown animal products. The few comparisons are confined to beef, milk, and egg yolk, with no data for swine or lamb products. δ 13 C appears to be the most promising isotopic marker to differentiate organic and conventional production systems when maize (C4) is present in the conventional animal diet. However, δ 13 C may be unsuitable under tropical conditions, where C4 grasses are abundant, and where grass-based husbandry is predominant in both conventional and organic systems. Presently, there is no universal analytical method that can be applied to differentiate organic and conventional animal products.

  7. Fractionation of Mercury Stable Isotopes during Microbial Methylmercury Production by Iron- and Sulfate-Reducing Bacteria.

    Science.gov (United States)

    Janssen, Sarah E; Schaefer, Jeffra K; Barkay, Tamar; Reinfelder, John R

    2016-08-02

    The biological production of monomethylmercury (MeHg) in soils and sediments is an important factor controlling mercury (Hg) accumulation in aquatic and terrestrial food webs. In this study we examined the fractionation of Hg stable isotopes during Hg methylation in nongrowing cultures of the anaerobic bacteria Geobacter sulfurreducens PCA and Desulfovibrio desulfuricans ND132. Both organisms showed mass-dependent, but no mass-independent fractionation of Hg stable isotopes during Hg methylation. Despite differences in methylation rates, the two bacteria had similar Hg fractionation factors (αr/p = 1.0009 and 1.0011, respectively). Unexpectedly, δ(202)Hg values of MeHg for both organisms were 0.4‰ higher than the value of initial inorganic Hg after about 35% of inorganic Hg had been methylated. These results indicate that a (202)Hg-enriched pool of inorganic Hg was preferentially utilized as a substrate for methylation by these organisms, but that multiple intra- and/or extracellular pools supplied inorganic Hg for biological methylation. Understanding the controls of the Hg stable isotopic composition of microbially produced MeHg is important to identifying bioavailable Hg in natural systems and the interpretation of Hg stable isotopes in aquatic food webs.

  8. Radiolytic decomposition of organic C-14 released from TRU waste

    International Nuclear Information System (INIS)

    Kani, Yuko; Noshita, Kenji; Kawasaki, Toru; Nishimura, Tsutomu; Sakuragi, Tomofumi; Asano, Hidekazu

    2007-01-01

    It has been found that metallic TRU waste releases considerable portions of C-14 in the form of organic molecules such as lower molecular weight organic acids, alcohols and aldehydes. Due to the low sorption ability of organic C-14, it is important to clarify the long-term behavior of organic forms under waste disposal conditions. From investigations on radiolytic decomposition of organic carbon molecules into inorganic carbonic acid, it is expected that radiation from TRU waste will decompose organic C-14 into inorganic carbonic acid that has higher adsorption ability into the engineering barriers. Hence we have studied the decomposition behavior of organic C-14 by gamma irradiation experiments under simulated disposal conditions. The results showed that organic C-14 reacted with OH radicals formed by radiolysis of water, to produce inorganic carbonic acid. We introduced the concept of 'decomposition efficiency' which expresses the percentage of OH radicals consumed for the decomposition reaction of organic molecules in order to analyze the experimental results. We estimated the effect of radiolytic decomposition on the concentration of organic C-14 in the simulated conditions of the TRU disposal system using the decomposition efficiency, and found that the concentration of organic C-14 in the waste package will be lowered when the decomposition of organic C-14 by radiolysis was taken into account, in comparison with the concentration of organic C-14 without radiolysis. Our prediction suggested that some amount of organic C-14 can be expected to be transformed into the inorganic form in the waste package in an actual system. (authors)

  9. Local radiolytic effectiveness of Auger electrons of iodine-125 in benzene-iodine solutions

    International Nuclear Information System (INIS)

    Uenak, P.; Uenak, T.

    1987-01-01

    High radiotoxicity of iodine-125 has been mainly attributed to the local radiolytic effects of Auger electrons on biological systems. In the present study, experimental and theoretical results are compared. The agreement between the experimental and theoretical results explains that the energy absorption of iodine aggregates has an important role in the radiolytic effectiveness of Auger electrons and iodine-125 in benzene-iodine solutions. (author) 18 refs.; 3 figs

  10. Principles and limitations of stable isotopes in differentiating organic and conventional foodstuffs: 1. Plant products.

    Science.gov (United States)

    Inácio, Caio Teves; Chalk, Phillip Michael; Magalhães, Alberto M T

    2015-01-01

    Among the lighter elements having two or more stable isotopes (H, C, N, O, S), δ(15)N appears to be the most promising isotopic marker to differentiate plant products from conventional and organic farms. Organic plant products vary within a range of δ(15)N values of +0.3 to +14.6%, while conventional plant products range from negative to positive values, i.e. -4.0 to +8.7%. The main factors affecting δ(15)N signatures of plants are N fertilizers, biological N2 fixation, plant organs and plant age. Correlations between mode of production and δ(13)C (except greenhouse tomatoes warmed with natural gas) or δ(34)S signatures have not been established, and δ(2)H and δ(18)O are unsuitable markers due to the overriding effect of climate on the isotopic composition of plant-available water. Because there is potential overlap between the δ(15)N signatures of organic and conventionally produced plant products, δ(15)N has seldom been used successfully as the sole criterion for differentiation, but when combined with complementary analytical techniques and appropriate statistical tools, the probability of a correct identification increases. The use of organic fertilizers by conventional farmers or the marketing of organic produce as conventional due to market pressures are additional factors confounding correct identification. The robustness of using δ(15)N to differentiate mode of production will depend on the establishment of databases that have been verified for individual plant products.

  11. Freedom: a transient fission-product release model for radioactive and stable species

    International Nuclear Information System (INIS)

    Macdonald, L.D.; Lewis, B.J.; Iglesias, F.C.

    1989-05-01

    A microstructure-dependent fission-gas release and swelling model (FREEDOM) has been developed for UO 2 fuel. The model describes the transient release behaviour for both the radioactive and stable fission-product species. The model can be applied over the full range of operating conditions, as well as for accident conditions that result in high fuel temperatures. The model accounts for lattice diffusion and grain-boundary sweeping of fusion products to the grain boundaries, where the fission gases accumulate in grain-face bubbles as a result of vacancy diffusion. Release of fission-gas to the free void of the fuel element occurs through the interlinkage of bubbles and cracks on the grain boundaries. This treatment also accounts for radioactive chain decay and neutron-induced transmutation effects. These phenomena are described by mass balance equations which are numerically solved using a moving-boundary, finite-element method with mesh refinement. The effects of grain-face bubbles on fuel swelling and fuel thermal conductivity are included in the ELESIM fuel performance code. FREEDOM has an accuracy of better than 1% when assessed against an analytic solution for diffusional release. The code is being evaluated against a fuel performance database for stable gas release, and against sweep-gas and in-cell fission-product release experiments at Chalk River for active species

  12. Development of safe and shelf-stable Intermediate Moisture (IM) convenience meat products through radiation processing

    International Nuclear Information System (INIS)

    Ramesh Chander; Kanatt, S.R.; Chawla, S.P.; Bongirwar, D.R.

    2001-01-01

    Ready-to-use shelf stable mutton and chicken sheek kababs, and chicken chilly were developed by reducing the water activity either by grilling or by hot air drying, vacuum packing and irradiation. Microbiological analysis revealed a dose dependent reduction in total viable count and in Staphylococcus species on irradiation treatment ( 2.5, 5.0 and 10.0 kGy). The products subjected to irradiation at 10 kGy showed absence of viable micro-organisms and also had high sensory acceptability up to 9 months at ambient temperature. (author)

  13. The Production of a Stable Infliximab Powder: The Evaluation of Spray and Freeze-Drying for Production

    Science.gov (United States)

    Kanojia, Gaurav; Have, Rimko ten; Bakker, Arjen; Wagner, Koen; Frijlink, Henderik W.; Kersten, Gideon F. A.; Amorij, Jean-Pierre

    2016-01-01

    In prospect of developing an oral dosage form of Infliximab, for treatment of Crohn’s disease and rheumatoid arthritis, freeze-drying (vial vs Lyoguard trays) and spray-drying were investigated as production method for stable powders. Dextran and inulin were used in combination with sucrose as stabilizing excipients. The drying processes did not affect Infliximab in these formulations, i.e. both the physical integrity and biological activity (TNF binding) were retained. Accelerated stability studies (1 month at 60°C) showed that the TNF binding ability of Infliximab was conserved in the freeze-dried formulations, whereas the liquid counterpart lost all TNF binding. After thermal treatment, the dried formulations showed some chemical modification of the IgG in the dextran-sucrose formulation, probably due to Maillard reaction products. This study indicates that, with the appropriate formulation, both spray-drying and freeze-drying may be useful for (bulk) powder production of Infliximab. PMID:27706175

  14. Study of the Potential Impact of Gamma-Induced Radiolytic Gases on Loading of Cesium Onto Crystalline Silicotitanate Sorbent at ORNL's High Flux Isotope Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Mattus, A.J.

    2001-02-12

    The use of an engineered form of crystalline silicotitanate as a potential sorbent for the removal and concentration of cesium from the high-level waste at the Savannah River Site was investigated. Results conclusively showed this sorbent to be unaffected by gamma-induced radiolytic gas formation during column loading. Closely controlled column-loading experiments were performed at the Oak Ridge National Laboratory's High Flux Isotope Reactor (HFIR) in a gamma field with a conservative dose rate expected to exceed that in a full-scale column by a factor of nearly 16. Operation of column loading under expected nominal full-scale field conditions in the HFIR pool showed that radiolytic gases were formed at a previously calculated generation rate of 0.4 mL per liter of feed solution. When the resulting cesium-loading curve in the gamma field was compared with that of a control experiment in the absence of a gamma field, no discernable difference in the curves (within analytical error) was detected. Both curves were in good agreement with the VERSE computer-generated curve. Results conclusively indicate that the production of radiolytic gases within a full-scale column is not expected to result in reduced capacity or associated gas generation problems during operation at the Savannah River Site.

  15. Room temperature stable CO x -free H2production from methanol with magnesium oxide nanophotocatalysts.

    Science.gov (United States)

    Liu, Zhengqing; Yin, Zongyou; Cox, Casandra; Bosman, Michel; Qian, Xiaofeng; Li, Na; Zhao, Hongyang; Du, Yaping; Li, Ju; Nocera, Daniel G

    2016-09-01

    Methanol, which contains 12.6 weight percent hydrogen, is a good hydrogen storage medium because it is a liquid at room temperature. However, by releasing the hydrogen, undesirable CO and/or CO 2 byproducts are formed during catalytic fuel reforming. We show that alkaline earth metal oxides, in our case MgO nanocrystals, exhibit stable photocatalytic activity for CO/CO 2 -free H 2 production from liquid methanol at room temperature. The performance of MgO nanocrystals toward methanol dehydrogenation increases with time and approaches ~320 μmol g -1 hour -1 after a 2-day photocatalytic reaction. The CO x -free H 2 production is attributed to methanol photodecomposition to formaldehyde, photocatalyzed by surface electronic states of unique monodispersed, porous MgO nanocrystals, which were synthesized with a novel facile colloidal chemical strategy. An oxygen plasma treatment allows for the removal of organic surfactants, producing MgO nanocrystals that are well dispersible in methanol.

  16. Cosmic-ray-produced stable nuclides: various production rates and their implications

    International Nuclear Information System (INIS)

    Reedy, R.C.

    1981-01-01

    The rates for a number of reactions producing certain stable nuclides, such as 3 He and 4 He, and fission in the moon are calculated for galactic-cosmic-ray particles and for solar protons. Solar-proton-induced reactions with bromine usually are not an important source of cosmogenic Kr isotopes. The 130 Ba(n,p) reaction cannot account for the undercalculation of 130 Xe production rates. Calculated production rates of 15 N, 13 C, and 2 H agree fairly well with rates inferred from measured excesses of these isotopes in samples with long exposure ages. Cosmic-ray-induced fission of U and Th can produce significant amounts of fission tracks and of 86 Kr, 134 Xe, and 136 Xe, especially in samples with long exposures to cosmic-ray particles

  17. Thermo-acid-stable phytase-mediated enhancement of bioethanol production using Colocasia esculenta.

    Science.gov (United States)

    Makolomakwa, Melvin; Puri, Adarsh Kumar; Permaul, Kugen; Singh, Suren

    2017-07-01

    Phytase production by the thermophilic mould Thermomyces lanuginosus SSBP was enhanced 8.56-fold in submerged fermentation, which was further improved in fed-batch cultivations. The protein was purified to homogeneity using ammonium sulphate precipitation, Resource Q anion exchange and Superdex gel-filtration chromatography, with an overall purification of 24.7-fold and a yield of 5.16%. The purified 49kDa protein was optimally active at 55°C and pH 5.0, and was stable between 50 and 90°C from pH 3.0-6.0, with a half-life of 138.6min at 70°C. It was moderately stimulated by Ba +2 and Mg +2 . The enzyme reduced phytate content in Colocasia esculenta starch (from 1.43mg/g to 0.05mg/g) that resulted in an improvement in the availability of fermentable sugars with a concomitant reduction in viscosity and 1.59-fold improvement in ethanol production. Thermo-acid-stable phytase from T. lanuginosus SSBP could be of major biotechnological interest, especially due to its robustness and wide applicability. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Stable Production of the Antimalarial Drug Artemisinin in the Moss Physcomitrella patens

    Directory of Open Access Journals (Sweden)

    Nur Kusaira Binti Khairul Ikram

    2017-08-01

    Full Text Available Malaria is a real and constant danger to nearly half of the world’s population of 7.4 billion people. In 2015, 212 million cases were reported along with 429,000 estimated deaths. The World Health Organization recommends artemisinin-based combinatorial therapies, and the artemisinin for this purpose is mainly isolated from the plant Artemisia annua. However, the plant supply of artemisinin is irregular, leading to fluctuation in prices. Here, we report the development of a simple, sustainable, and scalable production platform of artemisinin. The five genes involved in artemisinin biosynthesis were engineered into the moss Physcomitrella patens via direct in vivo assembly of multiple DNA fragments. In vivo biosynthesis of artemisinin was obtained without further modifications. A high initial production of 0.21 mg/g dry weight artemisinin was observed after only 3 days of cultivation. Our study shows that P. patens can be a sustainable and efficient production platform of artemisinin that without further modifications allow for industrial-scale production. A stable supply of artemisinin will lower the price of artemisinin-based treatments, hence become more affordable to the lower income communities most affected by malaria; an important step toward containment of this deadly disease threatening millions every year.

  19. Radiolytic stabilization of poly(methyl methacrylate) using commercial additives

    International Nuclear Information System (INIS)

    Aquino, Katia Aparecida da Silva

    2000-04-01

    Poly(methyl methacrylate), PMMA, Acrigel, a Brazilian polymer, is used in the manufacture of medical supplies sterelizable by ionizing radiation. However, when PMMA is gamma-irradiated it undergoes main chain scissions, which promote molecular degradation causing reduction in its mechanical properties. Therefore, radiolytic of PMMA is important for it to become commercially radiosterizable. In this work some commercial additives, originally used in photo-and thermo-oxidate stabilization of polymers, were tested. Only two additives, type HALS (Hindered Amine Light Stabilizer), denoted Scavenger, showed a good protective quality. The investigation of radiation-induced main scissions was carried out by viscosimetric method. The most effective additive, added to the polymer system at 0.3 w/w%, promotes a great molecular radioprotection of 93%. That means a reduction of G-value (scissions/100 eV) from 0.611 to 0.053. In addition, the glassy transition temperature (T g ) of PMMA (no additive) significantly changed by radiation does not change when PMMA (with additive) is irradiated. The spectroscopy analysis, FT-IR and NMR ( 1 H), showed that the radioprotector added to the system does not change the PMMA structure. (author)

  20. Partitioning of Evapotranspiration Using a Stable Water Isotope Technique in a High Temperature Agricultural Production System

    Science.gov (United States)

    Lu, X.; Liang, L.; Wang, L.; Jenerette, D.; Grantz, D. A.

    2015-12-01

    Agricultural production in the hot and arid low desert systems of southern California relies heavily on irrigation. A better understanding of how much and to what extent the irrigation water is transpired by crops relative to being lost through evaporation will contribute to better management of increasingly limited agricultural water resources. In this study, we examined the evapotranspiration (ET) partitioning over a field of forage sorghum (S. bicolor) during a growing season with several irrigation cycles. In several field campaigns we used continuous measurements of near-surface variations in the stable isotopic composition of water vapor (δ2H). We employed custom built transparent chambers coupled with a laser-based isotope analyzer and used Keeling plot and mass balance methods for surface flux partitioning. The preliminary results show that δT is more enriched than δE in the early growing season, and becomes less enriched than δE later in the season as canopy cover increases. There is an increase in the contribution of transpiration to ET as (1) leaf area index increases, and (2) as soil surface moisture declines. These results are consistent with theory, and extend these measurements to an environment that experiences extreme soil surface temperatures. The data further support the use of chamber based methods with stable isotopic analysis for characterization of ET partitioning in challenging field environments.

  1. Radiolytic degradation of gallic acid and its derivatives in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Melo, R. [Instituto Tecnologico e Nuclear, UCQR, Estrada Nacional No. 10, Apartado 21, 2686-953, Sacavem (Portugal); Leal, J.P. [Instituto Tecnologico e Nuclear, UCQR, Estrada Nacional No. 10, Apartado 21, 2686-953, Sacavem (Portugal); Centro Quimica e Bioquimica, Faculdade de Ciencias da Universidade de Lisboa, 1749-016 Lisboa (Portugal); Takacs, E., E-mail: takacs@iki.kfki.hu [Institute of Isotopes, Hungarian Academy of Sciences, P.O. Box 77, H-1525 Budapest (Hungary); Wojnarovits, L. [Institute of Isotopes, Hungarian Academy of Sciences, P.O. Box 77, H-1525 Budapest (Hungary)

    2009-12-30

    Polyphenols, like gallic acid (GA) released in the environment in larger amount, by inducing some unwanted oxidations, may constitute environmental hazard: their concentration in wastewater should be controlled. Radiolytic degradation of GA was investigated by pulse radiolysis and final product techniques in dilute aqueous solution. Subsidiary measurements were made with 3,4,5-trimethoxybenzoic acid (TMBA) and 3,4,5-trihydroxy methylbenzoate (MGA). The hydroxyl radical and hydrogen atom intermediates of water radiolysis react with the solute molecules yielding cyclohexadienyl radicals. The radicals formed in GA and MGA solutions in acid/base catalyzed water elimination decay to phenoxyl radicals. This reaction is not observed in TMBA solution. The hydrated electron intermediate of water decomposition adds to the carbonyl oxygen, the anion thus formed protonates on the ring forming cyclohexadienyl radical or on the carbonyl group forming carbonyl centred radical. The GA intermediates formed during reaction with primary water radicals in presence of oxygen transform to non-aromatic molecules, e.g., to aliphatic carboxylic acids.

  2. The development of transport and non-transport porosity in radiolytic graphite oxidation

    International Nuclear Information System (INIS)

    Blanchard, A.

    1980-01-01

    In graphite moderated, carbon dioxide cooled, reactors, radiolytic graphite oxidation arises from the production of short lived energetic species and is confined to the internal porous structure. Exponential weight loss is possible as the volume of internal porosity, absorbing radiation, increases with time. Inhibitors are added to the coolant to minimise weight and hence strength loss. Carbon monoxide and methane are the principal gas phase inhibitors, competing with the graphite for the oxidising species. Methane has the further effect of producing a sacrificial layer at the pore wall. It follows from the mechanisms of inhibition that oxidation is reduced in the larger pores. In the small pores, the probability is high that oxidising species will reach the pore wall and exponential weight loss can occur until such time as the pores become sufficiently large for the inhibitors to operate. The results from a high weight loss experiment confirm this behaviour and allow predictions to be made with some confidence for other coolants - for which initial oxidation rate data are available. In this paper the results from an earlier weight loss experiment in an 'uninhibited', nominally pure, carbon dioxide coolant are assessed. Particular attention is drawn to the information which can be obtained from a study of transport properties as they develop with graphite weight loss. The objectives in understanding more exactly the process occurring inside the complex pore structure are to allow extensions in planned life, or greater flexibility in coolant plant operation and compatibility with fuel clad. (author)

  3. Novel Radiolytic Rotenone Derivative, Rotenoisin B with Potent Anti-Carcinogenic Activity in Hepatic Cancer Cells

    Directory of Open Access Journals (Sweden)

    Srilatha Badaboina

    2015-07-01

    Full Text Available Rotenone, isolated from roots of derris plant, has been shown to possess various biological activities, which lead to attempting to develop a potent drug against several diseases. However, recent studies have demonstrated that rotenone has the potential to induce several adverse effects such as a neurodegenerative disease. Radiolytic transformation of the rotenone with gamma-irradiation created a new product, named rotenoisin B. The present work was designed to investigate the anticancer activity of rotenoisin B with low toxicity and its molecular mechanism in hepatic cancer cells compared to a parent compound, rotenone. Our results showed rotenoisin B inhibited hepatic cancer cells’ proliferation in a dose dependent manner and increased in apoptotic cells. Interestingly, rotenoisin B showed low toxic effects on normal cells compared to rotenone. Mitochondrial transmembrane potential has been decreased, which leads to cytochrome c release. Down regulation of anti-apoptotic Bcl-2 levels as well as the up regulation of proapoptotic Bax levels were observed. The cleaved PARP (poly ADP-ribose polymerase level increased as well. Moreover, phosphorylation of extracellular signal regulated kinase (ERK and p38 slightly up regulated and intracellular reactive oxygen species (ROS increased as well as cell cycle arrest predominantly at the G2/M phase observed. These results suggest that rotenoisin B might be a potent anticancer candidate similar to rotenone in hepatic cancer cells with low toxicity to normal cells even at high concentrations compared to rotenone.

  4. Carbon and nitrogen stable isotopes in U.S. milk: Insight into production process.

    Science.gov (United States)

    Bostic, Joshua N; Hagopian, William M; Jahren, A Hope

    2018-04-15

    Stable isotope analysis (SIA), a potential method of verifying the geographic origin and production method of dairy products, has not been applied to United States (U.S.) dairy samples on a national scale. To determine the potential of carbon and nitrogen SIA in authenticity assessment of U.S. dairy products, we analyzed a geographically representative collection of conventional milk samples to determine isotopic variations with (1) Purchase Location and (2) Macronutrient Content. A total of 136 milk samples spanning five commercially available varieties (3.25% [i.e., 'whole'], 2%, 1%, 0% [i.e., 'skim'] and 1% chocolate) were collected from randomly selected counties across the U.S. as part of the United States Department of Agriculture's (USDA's) National Food and Nutrient Analysis program. δ 13 C and δ 15 N values of bulk samples determined via elemental analysis/isotope ratio mass spectrometry (EA/IRMS) were used to assess the contribution of fat content, added sugar content and census-designated region of collection to isotopic variations within the dataset. There was a negative linear relationship between fat content and δ 13 C values, with average milk δ 13 C values decreasing by 0.33‰ for each 8.75% increase in dry weight (1% wet weight) fat content. The average δ 13 C value of flavored 1% chocolate milk samples, which contain an additional 12 g of added sugar, was 2.05‰ higher than that of 1% unflavored milk (-16.47‰ for chocolate milk vs -18.52‰ for unflavored milk). When controlling for macronutrient content, milk samples collected in West region supermarkets possessed significantly lower δ 13 C values than samples collected from Midwest, South, and Northeast regions. δ 15 N values did not vary with macronutrient content or region of collection. Carbon stable isotope ratios in U.S. milk samples varied with macronutrient content and region of purchase, suggesting that SIA can provide insight into production processes within the U.S. dairy

  5. Production of yeastolates for uniform stable isotope labelling in eukaryotic cell culture.

    NARCIS (Netherlands)

    Egorova-Zachernyuk, T.A.; Bosman, G.J.C.G.M.; Pistorius, A.M.A.; Grip, W.J. de

    2009-01-01

    Preparation of stable isotope-labelled yeastolates opens up ways to establish more cost-effective stable isotope labelling of biomolecules in insect and mammalian cell lines and hence to employ higher eukaryotic cell lines for stable isotope labelling of complex recombinant proteins. Therefore, we

  6. Novel Fast Pyrolysis/Catalytic Technology for the Production of Stable Upgraded Liquids

    Energy Technology Data Exchange (ETDEWEB)

    Oyama, Ted; Agblevor, Foster; Battaglia, Francine; Klein, Michael

    2013-01-18

    The objective of the proposed research is the demonstration and development of a novel biomass pyrolysis technology for the production of a stable bio-oil. The approach is to carry out catalytic hydrodeoxygenation (HDO) and upgrading together with pyrolysis in a single fluidized bed reactor with a unique two-level design that permits the physical separation of the two processes. The hydrogen required for the HDO will be generated in the catalytic section by the water-gas shift reaction employing recycled CO produced from the pyrolysis reaction itself. Thus, the use of a reactive recycle stream is another innovation in this technology. The catalysts will be designed in collaboration with BASF Catalysts LLC (formerly Engelhard Corporation), a leader in the manufacture of attrition-resistant cracking catalysts. The proposed work will include reactor modeling with state-of-the-art computational fluid dynamics in a supercomputer, and advanced kinetic analysis for optimization of bio-oil production. The stability of the bio-oil will be determined by viscosity, oxygen content, and acidity determinations in real and accelerated measurements. A multi-faceted team has been assembled to handle laboratory demonstration studies and computational analysis for optimization and scaleup.

  7. Room temperature stable COx-free H2 production from methanol with magnesium oxide nanophotocatalysts

    Science.gov (United States)

    Liu, Zhengqing; Yin, Zongyou; Cox, Casandra; Bosman, Michel; Qian, Xiaofeng; Li, Na; Zhao, Hongyang; Du, Yaping; Li, Ju; Nocera, Daniel G.

    2016-01-01

    Methanol, which contains 12.6 weight percent hydrogen, is a good hydrogen storage medium because it is a liquid at room temperature. However, by releasing the hydrogen, undesirable CO and/or CO2 byproducts are formed during catalytic fuel reforming. We show that alkaline earth metal oxides, in our case MgO nanocrystals, exhibit stable photocatalytic activity for CO/CO2-free H2 production from liquid methanol at room temperature. The performance of MgO nanocrystals toward methanol dehydrogenation increases with time and approaches ~320 μmol g−1 hour−1 after a 2-day photocatalytic reaction. The COx-free H2 production is attributed to methanol photodecomposition to formaldehyde, photocatalyzed by surface electronic states of unique monodispersed, porous MgO nanocrystals, which were synthesized with a novel facile colloidal chemical strategy. An oxygen plasma treatment allows for the removal of organic surfactants, producing MgO nanocrystals that are well dispersible in methanol. PMID:28508036

  8. Inhibition of the radiolytic hydrogen production in the nuclear waste of 'bitumen coated' type: study of the interaction between hydrogen and cobalt hydroxo-sulphide; Inhibition de la production d'hydrogene radiolytique dans les dechets nucleaires de type 'enrobes bitumineux': etude de l'interaction entre l'hydrogene et l'hydroxosulfure de cobalt

    Energy Technology Data Exchange (ETDEWEB)

    Pichon, C

    2006-11-15

    In the nuclear field in France, the bitumen is mainly used for the conditioning of the radioactive muds generated by the fuel reprocessing. However, the self-irradiation of the bitumen induces a production of hydrogen which generates safety problems. The comparison of various storage sites showed that the presence of cobalt hydroxo sulphide limited such a production. Consequently, this compound was regarded as an 'inhibitor of radiolytic hydrogen production'. However, the origin of this phenomenon was not clearly identified. In order to propose an explanation to this inhibition phenomenon, model organic molecules were used to represent the components of the bitumen. Irradiations were carried out by protons to simulate the alpha radiolysis. The organic molecules irradiations by a proton beam showed that cobalt hydroxo sulphide CoSOH, does not act as a hydrogenation catalyst of unsaturated hydrocarbons, nor as a radicals scavenger, but consists of a trap of hydrogen. Experiments of hydrogen trapping at ambient temperature were carried out according to two techniques: gravimetry and manometry. The solid was characterized before and after interaction with hydrogen (infrared and Raman spectroscopies, X-ray diffraction). The initial solid was composed of amorphous cobalt hydroxo sulphide and a minor phase of cobalt hydroxide. The gravimetry and manometry experiments showed that the maximum of hydrogen trapping capacity is equal to 0.59 {+-} 0.18 mole of hydrogen per mole of cobalt. After interaction with hydrogen, the Co(OH){sub 2} phase disappeared and a new solid phase appeared corresponding to Co{sub 9}S{sub 8}. These observations, as well as the analysis of the gas phase, made it possible to conclude with the following reaction (1): 9 CoSOH + 11/2 H{sub 2} = Co{sub 9}S{sub 8} + 9 H{sub 2}O + H{sub 2}S (1). Gravimetry experiments at temperatures between 50 and 210 C revealed the desorption of water but not of hydrogen sulphide. The absence of hydrogen

  9. Determination of yields of gaseous products of carbohydrates radiolysis by mass spectrometry method

    International Nuclear Information System (INIS)

    Ivko, A.A.; Gol'din, S.I.; Bondarenko, N.T.; Markevich, S.V.; Sharpatyj, V.A.

    1977-01-01

    Possible complications are treated involved in the mass spectral study of the radiolytic products of deuterated carbohydrates. A method is proposed suitable for the evaluation of hydrogen isotopes relations and the content of deuterium in water. It has been possible to identify the major gaseous radiolytic products of glucose, polyglucan and dextran, and also to assess their radiation-chemical yields [ru

  10. Iron release from ferritin and lipid peroxidation by radiolytically generated reducing radicals

    International Nuclear Information System (INIS)

    Reif, D.W.; Schubert, J.; Aust, S.D.

    1988-01-01

    Iron is involved in the formation of oxidants capable of damaging membranes, protein, and DNA. Using 137 Cs gamma radiation, we investigated the release of iron from ferritin and concomitant lipid peroxidation by radiolytically generated reducing radicals, superoxide and the carbon dioxide anion radical. Both radicals released iron from ferritin with similar efficiencies and iron mobilization from ferritin required an iron chelator. Radiolytically generated superoxide anion resulted in peroxidation of phospholipid liposomes as measured by malondialdehyde formation only when ferritin was included as an iron source and the released iron was found to be chelated by the phospholipid liposomes

  11. Dewatered sewage biosolids provide a productive larval habitat for stable flies and house flies (Diptera: Muscidae).

    Science.gov (United States)

    Doud, C W; Taylor, D B; Zurek, L

    2012-03-01

    Species diversity and seasonal abundance of muscoid flies (Diptera: Muscidae) developing in biosolid cake (dewatered biosolids) stored at a wastewater treatment facility in northeastern Kansas were evaluated. Emergence traps were deployed 19 May through 20 October 2009 (22 wk) and 27 May through 18 November 2010 (25 wk). In total, 11,349 muscoid flies were collected emerging from the biosolid cake. Stable flies (Stomoxys calcitrans (L.)) and house flies (Musca domestica (L.)), represented 80 and 18% of the muscoid flies, respectively. An estimated 550 stable flies and 220 house flies per square-meter of surface area developed in the biosolid cake annually producing 450,000 stable flies and 175,000 house flies. Stable fly emergence was seasonally bimodal with a primary peak in mid-July and a secondary peak in late August. House fly emergence peaked with the first stable fly emergence peak and then declined gradually for the remainder of the year. House flies tended to emerge from the biosolid cake sooner after its deposition than did stable flies. In addition, house fly emergence was concentrated around midsummer whereas stable fly emergence began earlier in the spring and continued later into the fall. Biosolid age and temperature were the most important parameters affecting emergence for house flies and stable flies, whereas precipitation was not important for either species. This study highlights the importance of biosolid cake as a larval developmental habitat for stable flies and house flies.

  12. Production of stable food-grade microencapsulated astaxanthin by vibrating nozzle technology.

    Science.gov (United States)

    Vakarelova, Martina; Zanoni, Francesca; Lardo, Piergiovanni; Rossin, Giacomo; Mainente, Federica; Chignola, Roberto; Menin, Alessia; Rizzi, Corrado; Zoccatelli, Gianni

    2017-04-15

    Astaxanthin is a carotenoid known for its strong antioxidant and health-promoting characteristics, but it is also highly degradable and thus unsuited for several applications. We developed a sustainable method for the extraction and the production of stable astaxanthin microencapsulates. Nearly 2% astaxanthin was extracted by high-pressure homogenization of dried Haematococcus pluvialis cells in soybean oil. Astaxanthin-enriched oil was encapsulated in alginate and low-methoxyl pectin by Ca 2+ -mediated vibrating-nozzle extrusion technology. The 3% pectin microbeads resulted the best compromise between sphericity and oil retention upon drying. We monitored the stability of these astaxanthin beads under four different conditions of light, temperature and oxygen exposition. After 52weeks, the microbeads showed a total-astaxanthin retention of 94.1±4.1% (+4°C/-light/+O 2 ), 83.1±3.2% (RT/-light/-O 2 ), 38.3±2.2% (RT/-light/+O2), and 57.0±0.4% (RT/+light/+O 2 ), with different degradation kinetics. Refrigeration, therefore, resulted the optimal storage condition to preserve astaxanthin stability. Copyright © 2016 Elsevier Ltd. All rights reserved.

  13. Use Of Stable Isotope To Determine Time of Red River Water Recharging To Production Groundwater Wells In Hanoi

    International Nuclear Information System (INIS)

    Trinh Van Giap; Dang Anh Minh

    2011-01-01

    Stable isotope O-18 and lump parameter models has been used to determine time of Red River water recharging to some production groundwater wells at Yen Phu station in Ha noi. Composition of stable isotope O-18 in Red River water changed on time in a year has been used as a tracer with lump parameter models to study flow of groundwater. Composition of stable isotope O-18 in production groundwater wells was measured on months in a year and the fitting of measured data and calculation data with selected flow models was carried out by lumped parameter models. The results of fitting shows resident time or time of Red River water recharging to production groundwater wells. At 4 production groundwater wells of Yen Phu station selected in this study, the time of Red River water recharging to wells H26 and H29 is following 3.5 months and 11 months. Composition of stable isotope O-18 at wells H12 and H27 do not change on time, but proportions of Red River water in production groundwater at these wells were calculated of following 99% and 97%. (author)

  14. Parametric studies of radiolytic oxidation of iodide solutions with and without paint: comparison with code calculations

    Energy Technology Data Exchange (ETDEWEB)

    Poletiko, C.; Hueber, C. [Inst. de Protection et de Surete Nucleaire, C.E. Cadarache, St. Paul-lez-Durance (France); Fabre, B. [CISI, C.E. Cadarache, St. Paul-lez-Durance (France)

    1996-12-01

    In case of severe nuclear accident, radioactive material may be released into the environment. Among the fission products involved, are the very volatile iodine isotopes. However, the chemical forms are not well known due to the presence of different species in the containment with which iodine may rapidly react to form aerosols, molecular iodine, hydroiodic acid and iodo-organics. Tentative explanations of different mechanisms were performed through benchscale tests. A series of tests has been performed at AEA Harwell (GB) to study parameters such as pH, dose rate, concentration, gas flow rate, temperature in relation to molecular iodine production, under dynamic conditions. Another set of tests has been performed in AECL Whiteshell (CA) to study the behaviour of painted coupons, standing in gas phase or liquid phase or both, with iodine compounds under radiation. The purpose of our paper is to synthesize the data and compare the results to the IODE code calculation. Some parameters of the code were studied to fit the experimental result the best. A law, concerning the reverse reaction of iodide radiolytic oxidation, has been proposed versus: pH, concentrations and gas flow-rate. This law does not apply for dose rate variations. For the study of painted coupons, it has been pointed out that molecular iodine tends to be adsorbed or chemically absorbed on the surface in gas phase, but the mechanism should be more sophisticated in the aqueous phase. The iodo-organics present in liquid phase tend to be partly or totally destroyed by oxidation under radiation (depending upon the dose delivered). These points are discussed. (author) 18 figs., 3 tabs., 15 refs.

  15. Pilot scale production of highly efficacious and stable enterovirus 71 vaccine candidates.

    Directory of Open Access Journals (Sweden)

    Ai-Hsiang Chou

    Full Text Available BACKGROUND: Enterovirus 71 (EV71 has caused several epidemics of hand, foot and mouth diseases (HFMD in Asia and now is being recognized as an important neurotropic virus. Effective medications and prophylactic vaccine against EV71 infection are urgently needed. Based on the success of inactivated poliovirus vaccine, a prototype chemically inactivated EV71 vaccine candidate has been developed and currently in human phase 1 clinical trial. PRINCIPAL FINDING: In this report, we present the development of a serum-free cell-based EV71 vaccine. The optimization at each step of the manufacturing process was investigated, characterized and quantified. In the up-stream process development, different commercially available cell culture media either containing serum or serum-free was screened for cell growth and virus yield using the roller-bottle technology. VP-SFM serum-free medium was selected based on the Vero cell growth profile and EV71 virus production. After the up-stream processes (virus harvest, diafiltration and concentration, a combination of gel-filtration liquid chromatography and/or sucrose-gradient ultracentrifugation down-stream purification processes were investigated at a pilot scale of 40 liters each. Although the combination of chromatography and sucrose-gradient ultracentrifugation produced extremely pure EV71 infectious virus particles, the overall yield of vaccine was 7-10% as determined by a VP2-based quantitative ELISA. Using chromatography as the downstream purification, the virus yield was 30-43%. To retain the integrity of virus neutralization epitopes and the stability of the vaccine product, the best virus inactivation was found to be 0.025% formalin-treatment at 37 °C for 3 to 6 days. Furthermore, the formalin-inactivated virion vaccine candidate was found to be stable for >18 months at 4 °C and a microgram of viral proteins formulated with alum adjuvant could induce strong virus-neutralizing antibody responses in mice

  16. Annealing of radiolytic damage and exchange in Co(H/sub 2/O)/sub 6/ x (CoEDTA)/sub 2/ x 4H/sub 2/O. [Gamma radiation

    Energy Technology Data Exchange (ETDEWEB)

    Albarran, G.; Archundia, C.; Maddock, A.G.

    1984-01-01

    To clarify the mechanism of cobalt exchange in irradiated Co(H/sub 2/O)/sub 6/x(CoEDTA)/sub 2/x4H/sub 2/O the radiolytic products have been investigated. The neutral, two negatively and one positively charged species formed reform the original complex on thermal annealing. This annealing process seems to be preceeded by the exchange process.

  17. Status of stable isotope enrichment, products, and services at the Oak Ridge National Laboratory

    Science.gov (United States)

    Scott Aaron, W.; Tracy, Joe G.; Collins, Emory D.

    1997-02-01

    The Oak Ridge National Laboratory (ORNL) has been supplying enriched stable and radioactive isotopes to the research, medical, and industrial communities for over 50 y. Very significant changes have occurred in this effort over the past several years, and, while many of these changes have had a negative impact on the availability of enriched isotopes, more recent developments are actually improving the situation for both the users and the producers of enriched isotopes. ORNL is still a major producer and distributor of radioisotopes, but future isotope enrichment operations to be conducted at the Isotope Enrichment Facility (IEF) will be limited to stable isotopes. Among the positive changes in the enriched stable isotope area are a well-functioning, long-term contract program, which offers stability and pricing advantages; the resumption of calutron operations; the adoption of prorated conversion charges, which greatly improves the pricing of isotopes to small users; ISO 9002 registration of the IEF's quality management system; and a much more customer-oriented business philosophy. Efforts are also being made to restore and improve upon the extensive chemical and physical form processing capablities that once existed in the enriched stable isotope program. Innovative ideas are being pursued in both technical and administrative areas to encourage the beneficial use of enriched stable isotopes and the development of related technologies.

  18. Status of stable isotope enrichment, products, and services at the Oak Ridge National Laboratory

    International Nuclear Information System (INIS)

    Aaron, W.S.; Tracy, J.G.; Collins, E.D.

    1996-01-01

    The Oak Ridge National Laboratory (ORNL) has been supplying enriched stable and radioactive isotopes to the research, medical, and industrial communities for over 50 years. Very significant changes have occurred in this effort over the past several years, and, while many of these changes have had a negative impact on the availability of enriched isotopes, more recent developments are actually improving the situation for both the users and the producers of enriched isotopes. ORNL is still a major producer and distributor of radioisotopes, but future isotope enrichment operations conducted at the Isotope Enrichment Facility (IEF) will be limited to stable isotopes. Among the positive changes in the enriched stable isotope area are a well-functioning, long-term contract program, which offers stability and pricing advantages; the resumption of calutron operations; the adoption of prorated conversion charges, which greatly improves the pricing of isotopes to small users; SIO 9002 registration of the IEF's quality management system; and a much more customer-oriented business philosophy. Efforts are also being made to restore and improve upon the extensive chemical and physical form processing capabilities that once existed in the enriched stable isotope program. Innovative ideas are being pursued in both technical and administrative areas to encourage the beneficial use of enriched stable isotopes and the development of related technologies

  19. Accelerating patient access to novel biologics using stable pool-derived product for non-clinical studies and single clone-derived product for clinical studies.

    Science.gov (United States)

    Munro, Trent P; Le, Kim; Le, Huong; Zhang, Li; Stevens, Jennitte; Soice, Neil; Benchaar, Sabrina A; Hong, Robert W; Goudar, Chetan T

    2017-11-01

    Cell cloning and subsequent process development activities are on the critical path directly impacting the timeline for advancement of next generation therapies to patients with unmet medical needs. The use of stable cell pools for early stage material generation and process development activities is an enabling technology to reduce timelines. To successfully use stable pools during development, it is important that bioprocess performance and requisite product quality attributes be comparable to those observed from clonally derived cell lines. To better understand the relationship between pool and clone derived cell lines, we compared data across recent first in human (FIH) programs at Amgen including both mAb and Fc-fusion modalities. We compared expression and phenotypic stability, bioprocess performance, and product quality attributes between material derived from stable pools and clonally derived cells. Overall, our results indicated the feasibility of matching bioprocess performance and product quality attributes between stable pools and subsequently derived clones. These findings support the use of stable pools to accelerate the advancement of novel biologics to the clinic. © 2017 The Authors Biotechnology Progress published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers Biotechnol. Prog., 33:1476-1482, 2017. © 2017 The Authors Biotechnology Progress published by Wiley Periodicals, Inc. on behalf of American Institute of Chemical Engineers.

  20. Stable Isotope and Isotopomeric Constraints on Nitrous Oxide Production in a Wastewater Treatment Plant

    Science.gov (United States)

    Bellucci, F.; Gonzalez-Meler, M. A.; Sturchio, N. C.; Bohlke, J. K.; Ostrom, N. E.; Kozak, J. A.

    2011-12-01

    Estimates of US anthropogenic greenhouse gas emissions by USEPA (Inventory of U.S. Greenhouse Gas Emissions and Sinks: 1990-2009; 2011) indicate that wastewater treatment plants are the 7th highest contributor to atmospheric nitrous oxide. This unregulated gas has an estimated global warming potential (GWP) 310 times that of carbon dioxide on a per mol basis. There is general agreement that, within wastewater treatment plants, the vast majority of the nitrous oxide emissions occur in the aerobic zones for biological ammonia oxidation and/or downstream from anoxic zones used in biological nitrogen removal. However, the exact mechanism of production is not well understood, as both incomplete nitrification and denitrification might contribute to the overall nitrous oxide emissions. Determining the dominant biological pathways responsible for these emissions is important for the development of improved treatment systems that can reduce nitrous oxide greenhouse gas emissions to the atmosphere. In this study, we determined the total nitrous oxide flux from a single tank of one of the aeration basins from a large metropolitan wastewater treatment plant in Stickney, Illinois. Furthermore, we analyzed the changes in nitrogen and oxigen stable isotopic composition for ammonium, nitrate, and nitrous oxide, as well as the intramolecular site preference (SP) for δ15N within the linear N-N-O molecule, along the 520 meter wastewater flow path within the tank. Assuming the measured tank was representative of the 32 tanks constituting the 4 aeration basins of the plant, we estimate the combined annual nitrous oxide flux from this source to be approximately 230 metric ton/y. The δ15N values for ammonium ranged between +19.9% and +6.4%, those for nitrate ranged between +20.4% and +5.3%, and those for nitrous oxide ranged between -34.4% and 0.4%. The nitrous oxide SP ranged between +11.7% and -4.5%. The concentrations and δ15N values of ammonium and nitrate showed trends along the

  1. Stable isotope composition of environmental water and food products as a tracer of origin

    International Nuclear Information System (INIS)

    Wierzchnicki, R.; Owczarczyk, A.; Soltyk, W.

    2004-01-01

    The paper is the review of Institute of Nuclear Chemistry and Technology (INCT) activity in application of stable isotope ratios (especially D/H and 18 O/ 16 O) for environmental studies and food origin control. INCT has at disposal since 1998, a high class instrument - Isotope Ratio Mass Spectrometer, Delta Plus, Finnigan MAT, Germany - suitable to perform such measurements. (author)

  2. Systematic screening of different surface modifiers for the production of physically stable nanosuspensions.

    Science.gov (United States)

    Lestari, Maria L A D; Müller, Rainer H; Möschwitzer, Jan P

    2015-03-01

    The role of a surface modifier is important in the formation of stable nanosuspensions. In this study, a simple and systematic screening method for selecting optimum surface modifiers was performed by utilizing a low-energy wet ball milling method. Nine surface modifiers from different classes with different stabilization mechanisms were applied on six different models of active pharmaceutical ingredients (API). Particle size analysis showed that at concentration five times higher than the critical micelle concentration, SDS and sodium cholate (anionic surfactant) showed the highest percent success to produce stable nanosuspensions with particle size smaller than 250 nm. Similar findings were also shown by poloxamer 188 (nonionic surfactant) and hydroxypropylmethylcellulose E5 (polymeric stabilizer) at concentration 1% (w/v) and 0.8% (w/v), respectively. In addition, combinations of anionic surfactant and nonionic surfactant as well as combinations of anionic surfactant and polymeric stabilizer showed high percent success in the formation of stable nanosuspensions. In general, no correlation can be found between the physicochemical characteristics of the model API (molecular weight, melting point, log P, pKa, and crystallinity) with its feasibility to be nanosized. The concentration and the principle of stabilization of surface modifier determine the formation of stable nanosuspensions. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  3. The importance of variables and parameters in radiolytic chemical kinetics modeling

    International Nuclear Information System (INIS)

    Piepho, M.G.; Turner, P.J.; Reimus, P.W.

    1989-01-01

    Many of the pertinent radiochemical reactions are not completely understood, and most of the associated rate constants are poorly characterized. To help identify the important radiochemical reactions, rate constants, species, and environmental conditions, an importance theory code, SWATS (Sensitivitiy With Adjoint Theory-Sparse version)-LOOPCHEM, has been developed for the radiolytic chemical kinetics model in the radiolysis code LOOPCHEM. The LOOPCHEM code calculates the concentrations of various species in a radiolytic field over time. The SWATS-LOOPCHEM code efficiently calculates: the importance (relative to a defined response of interest) of each species concentration over time, the sensitivity of each parameter of interest, and the importance of each equation in the radiolysis model. The calculated results will be used to guide future experimental and modeling work for determining the importance of radiolysis on waste package performance. A demonstration (the importance of selected concentrations and the sensitivities of selected parameters) of the SWATS-LOOPCHEM code is provided for illustrative purposes

  4. The complex reaction sequence of the thermal and radiolytic degradation of polyvinyl chloride

    International Nuclear Information System (INIS)

    Reichert, W.

    1983-03-01

    The degradation of PVC-foils was been tested by thermal and radiolytic stress in N 2 - and O 2 -atmosphere. Additionally was determined the influence of plasticizers, Fe-, Zn- and Cu-stearates and other additives, which partially are known as stabilizators. Complex mechanisms of degradation are proposed, which were deduced from the HCl-elimination, consumption of oxygen and the shift of the molmass by the scission and crosslinking of main chains both for PVC as combination of PVC with additives. The mechanism corresponds to other known experimental results, too. It was shown, that the radiolytical degradation caused by radicals, which initiate a radical chain mechanism, if the temperature is higher than the glass temperature (Tg). The thermical degradation in a N 2 -atmosphere was explained by an ionic complex mechanism. At the presence of oxygen the ionic mechanism was superimposed by a radical chain mechanism following the oxidation of polyene structures. (author)

  5. Enhanced Production and Characterization of a Solvent Stable Amylase from Solvent Tolerant Bacillus tequilensis RG-01: Thermostable and Surfactant Resistant

    OpenAIRE

    Tiwari, Soni; Shukla, Neha; Mishra, Pooja; Gaur, Rajeeva

    2014-01-01

    Ten bacterial strains isolated from the soil samples in the presence of cyclohexane were screened for amylase production. Among them, culture RG-01 was adjudged as the best amylase producer and was identified as Bacillus tequilensis from MTCC, Chandigarh. The isolate showed maximum amylase production (8100 U/mL) in the presence of starch, peptone, and Ca2+ ions at 55°C pH 7.0 within 24 h of incubation. The enzyme was stable in the presence of n-dodecane, isooctane, n-decane, xylene, toluene, ...

  6. Using stable isotopes to follow excreta N dynamics and N2O emissions in animal production systems.

    Science.gov (United States)

    Clough, T J; Müller, C; Laughlin, R J

    2013-06-01

    Nitrous oxide (N2O) is a potent greenhouse gas and the dominant anthropogenic stratospheric ozone-depleting emission. The tropospheric concentration of N2O continues to increase, with animal production systems constituting the largest anthropogenic source. Stable isotopes of nitrogen (N) provide tools for constraining emission sources and, following the temporal dynamics of N2O, providing additional insight and unequivocal proof of N2O source, production pathways and consumption. The potential for using stable isotopes of N is underutilised. The intent of this article is to provide an overview of what these tools are and demonstrate where and how these tools could be applied to advance the mitigation of N2O emissions from animal production systems. Nitrogen inputs and outputs are dominated by fertiliser and excreta, respectively, both of which are substrates for N2O production. These substrates can be labelled with 15N to enable the substrate-N to be traced and linked to N2O emissions. Thus, the effects of changes to animal production systems to reduce feed-N wastage by animals and fertiliser wastage, aimed at N2O mitigation and/or improved animal or economic performance, can be traced. Further 15N-tracer studies are required to fully understand the dynamics and N2O fluxes associated with excreta, and the biological contribution to these fluxes. These data are also essential for the new generation of 15N models. Recent technique developments in isotopomer science along with stable isotope probing using multiple isotopes also offer exciting capability for addressing the N2O mitigation quest.

  7. Structural and behavioral characteristics of radiolytically synthesized polyacrylic acid–polyacrylonitrile copolymeric hydrogels

    International Nuclear Information System (INIS)

    Bera, Anuradha; Misra, R.K.; Singh, Shailendra K.

    2013-01-01

    Copolymeric hydrogels of polyacrylic acid (PAA) – polyacrylonitrile (PAN) was radiolytically synthesized from their respective monomers with trimethyloltrimethacrylate (TMPTMA) as the crosslinker wherein both polymerization and crosslinking could be achieved in a single step reaction using 60 Co γ-radiation under varying doses and dose rates. The formation of the hydrogels was confirmed by their FT-IR analysis, while their thermal degradation patterns were investigated through thermogravimetric analysis in both the dry and swelled state. The water sorption studies showed rapid swelling behavior of these hydrogels, where swelling (%EWC) was found to be strongly dependent on the ratio of the two monomers in the hydrogels and the swelling kinetics dependent on the dose rates of hydrogel synthesis. These radiolytically synthesized hydrogels responded to electrical stimulus both in terms of the bending speed as well as bending angle under an applied voltage. The nature of the deformation was reversible and can be controlled through switching the voltage on and off. - Highlights: • Polyacrylic acid – polyacrilonitrile copolymeric hydrogel has been radiolytically synthesized. • Trimethyloltrimethacrylate (TMPTMA) used as crosslinker. • Hydrogel has been characterized and tested for electroresponsive character. • Bending angles and bending speed were found dependent upon applied voltage

  8. Bioprocess optimization for production of thermoalkali-stable protease from Bacillus subtilis K-1 under solid-state fermentation.

    Science.gov (United States)

    Singh, Satbir; Bajaj, Bijender Kumar

    2016-10-02

    Cost-effective production of proteases, which are robust enough to function under harsh process conditions, is always sought after due to their wide industrial application spectra. Solid-state production of enzymes using agro-industrial wastes as substrates is an environment-friendly approach, and it has several advantages such as high productivity, cost-effectiveness, being less labor-intensive, and less effluent production, among others. In the current study, different agro-wastes were employed for thermoalkali-stable protease production from Bacillus subtilis K-1 under solid-state fermentation. Agricultural residues such as cotton seed cake supported maximum protease production (728 U ml(-1)), which was followed by gram husk (714 U ml(-1)), mustard cake (680 U ml(-1)), and soybean meal (653 U ml(-1)). Plackett-Burman design of experiment showed that peptone, moisture content, temperature, phosphates, and inoculum size were the significant variables that influenced the protease production. Furthermore, statistical optimization of three variables, namely peptone, moisture content, and incubation temperature, by response surface methodology resulted in 40% enhanced protease production as compared to that under unoptimized conditions (from initial 728 to 1020 U ml(-1)). Thus, solid-state fermentation coupled with design of experiment tools represents a cost-effective strategy for production of industrial enzymes.

  9. Landscape variation in the diet and productivity of reindeer in Alaska based on stable isotope analyses

    Science.gov (United States)

    Gregory L. Finstad; Knut Kielland

    2011-01-01

    Productivity of a managed grazing system is dependent upon both the grazing strategy of ungulates and decisions made by humans. Herds of domestic reindeer (Rangifer tarandus tarandus) graze on discrete ranges of the Seward Peninsula, Alaska with variable production rates. We show that the 15N natural abundance of reindeer...

  10. Stable acetate production in extreme-thermophilic (70°C) mixed culture fermentation by selective enrichment of hydrogenotrophic methanogens

    Science.gov (United States)

    Zhang, Fang; Zhang, Yan; Ding, Jing; Dai, Kun; van Loosdrecht, Mark C. M.; Zeng, Raymond J.

    2014-06-01

    The control of metabolite production is difficult in mixed culture fermentation. This is particularly related to hydrogen inhibition. In this work, hydrogenotrophic methanogens were selectively enriched to reduce the hydrogen partial pressure and to realize efficient acetate production in extreme-thermophilic (70°C) mixed culture fermentation. The continuous stirred tank reactor (CSTR) was stable operated during 100 days, in which acetate accounted for more than 90% of metabolites in liquid solutions. The yields of acetate, methane and biomass in CSTR were 1.5 +/- 0.06, 1.0 +/- 0.13 and 0.4 +/- 0.05 mol/mol glucose, respectively, close to the theoretical expected values. The CSTR effluent was stable and no further conversion occurred when incubated for 14 days in a batch reactor. In fed-batch experiments, acetate could be produced up to 34.4 g/L, significantly higher than observed in common hydrogen producing fermentations. Acetate also accounted for more than 90% of soluble products formed in these fed-batch fermentations. The microbial community analysis revealed hydrogenotrophic methanogens (mainly Methanothermobacter thermautotrophicus and Methanobacterium thermoaggregans) as 98% of Archaea, confirming that high temperature will select hydrogenotrophic methanogens over aceticlastic methanogens effectively. This work demonstrated a potential application to effectively produce acetate as a value chemical and methane as an energy gas together via mixed culture fermentation.

  11. Antibiotics-free stable polyhydroxyalkanoate (PHA) production from carbon dioxide by recombinant cyanobacteria.

    Science.gov (United States)

    Akiyama, Hideo; Okuhata, Hiroshi; Onizuka, Takuo; Kanai, Shozo; Hirano, Masahiko; Tanaka, Satoshi; Sasaki, Ken; Miyasaka, Hitoshi

    2011-12-01

    A practical antibiotics-free plasmid expression system in cyanobacteria was developed by using the complementation of cyanobacterial recA null mutation with the EscherichiacolirecA gene on the plasmid. This system was applied to the production of polyhydroxyalkanoate (PHA), a biodegradable plastic, and the transgenic cyanobacteria stably maintained the pha genes for PHA production in the antibiotics-free medium, and accumulated up to 52% cell dry weight of PHA. Copyright © 2011 Elsevier Ltd. All rights reserved.

  12. Liquid phase mass production of air-stable black phosphorus/phospholipids nanocomposite with ultralow tunneling barrier

    Science.gov (United States)

    Zhang, Qiankun; Liu, Yinan; Lai, Jiawei; Qi, Shaomian; An, Chunhua; Lu, Yao; Duan, Xuexin; Pang, Wei; Zhang, Daihua; Sun, Dong; Chen, Jian-Hao; Liu, Jing

    2018-04-01

    Few-layer black phosphorus (FLBP), a recently discovered two-dimensional semiconductor, has attracted substantial attention in the scientific and technical communities due to its great potential in electronic and optoelectronic applications. However, reactivity of FLBP flakes with ambient species limits its direct applications. Among various methods to passivate FLBP in ambient environment, nanocomposites mixing FLBP flakes with stable matrix may be one of the most promising approaches for industry applications. Here, we report a simple one-step procedure to mass produce air-stable FLBP/phospholipids nanocomposite in liquid phase. The resultant nanocomposite is found to have ultralow tunneling barrier for charge carriers which can be described by an Efros-Shklovskii variable range hopping mechanism. Devices made from such mass-produced FLBP/phospholipids nanocomposite show highly stable electrical conductivity and opto-electrical response in ambient conditions, indicating its promising applications in both electronic and optoelectronic applications. This method could also be generalized to the mass production of nanocomposites consisting of other air-sensitive 2D materials, such as FeSe, NbSe2, WTe2, etc.

  13. Stable and Highly Efficient Electrochemical Production of Formic Acid from Carbon Dioxide Using Diamond Electrodes.

    Science.gov (United States)

    Natsui, Keisuke; Iwakawa, Hitomi; Ikemiya, Norihito; Nakata, Kazuya; Einaga, Yasuaki

    2018-03-01

    High faradaic efficiencies can be achieved in the production of formic acid (HCOOH) by metal electrodes, such as Sn or Pb, in the electrochemical reduction of carbon dioxide (CO 2 ). However, the stability and environmental load in using them are problematic. The electrochemical reduction of CO 2 to HCOOH was investigated in a flow cell using boron-doped diamond (BDD) electrodes. BDD electrodes have superior electrochemical properties to metal electrodes, and, moreover, are highly durable. The faradaic efficiency for the production of HCOOH was as high as 94.7 %. Furthermore, the selectivity for the production of HCOOH was more than 99 %. The rate of the production was increased to 473 μmol m -2  s -1 at a current density of 15 mA cm -2 with a faradaic efficiency of 61 %. The faradaic efficiency and the production rate are almost the same as or larger than those achieved using Sn and Pb electrodes. Furthermore, the stability of the BDD electrodes was confirmed by 24 h operation. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Development and quality characteristics of shelf-stable soy-agushie: a residual by-product of soymilk production.

    Science.gov (United States)

    Nti, Christina A; Plahar, Wisdom A; Annan, Nana T

    2016-03-01

    A process was developed for the production of a high-protein food ingredient, soy-agushie, from the residual by-product of soymilk production. The product, with a moisture content of about 6%, was evaluated for its quality characteristics and performance in traditional dishes. The protein content was about 26% with similar amino acids content as that of the whole soybean. Lysine remained high in the dehydrated product (6.57 g/16 g N). While over 60% of the original B vitamins content in the beans was extracted with the milk, high proportions of the minerals were found to be retained in the residual by-product. The process adequately reduced the trypsin inhibitor levels in the beans from 25 to 1.5 mg/g. High sensory scores were obtained for recipes developed with soy-agushie in traditional dishes. The scope of utilization of the soy-agushie could be widened to include several traditional foods and bakery products for maximum nutritional benefits.

  15. Unbiased Spontaneous Solar Fuel Production using Stable LaFeO3 Photoelectrode.

    Science.gov (United States)

    Pawar, Govinder S; Tahir, Asif A

    2018-02-22

    Photoelectrochemical (PEC) water splitting to produce solar fuel (hydrogen) has long been considered as the Holy Grail to a carbon-free hydrogen economy. The PEC concept to produce solar fuel is to emulate the natural photosynthesis using man made materials. The bottle-neck in realising the concept practically has been the difficulty in identifying stable low-cost semiconductors that meet the thermodynamic and kinetic criteria for photoelectrolysis. We have fabricated a novel p-type LaFeO 3 photoelectrode using an inexpensive and scalable spray pyrolysis method. Our nanostructured LaFeO 3 photoelectrode results in spontaneous hydrogen evolution from water without any external bias applied. Moreover, the photoelectrode has a faradaic efficiency of 30% and showed excellent stability over 21 hours. From optical and impedance data, the constructed band diagram showed that LaFeO 3 can straddle the water redox potential with the conduction band at -1.11 V above the reduction potential of hydrogen. We have fabricated a low cost LaFeO 3 photoelectrode that can spontaneously produce hydrogen from water using sunlight, making it a strong future candidate for renewable hydrogen generation.

  16. Stable BC 2N nanostructures: low-temperature production of segregated C/BN layered materials

    Science.gov (United States)

    Kohler-Redlich, Ph.; Terrones, M.; Manteca-Diego, C.; Hsu, W. K.; Terrones, H.; Rühle, M.; Kroto, H. W.; Walton, D. R. M.

    1999-09-01

    Stable filaments of nanometer dimensions with overall chemical stoichiometry close to BC 2N were generated by pyrolysis of CH 3CN·BCl 3 over Co at 1000°C and, for the first time, their structures were investigated, at the nanometer level, using high spatial resolution electron energy-loss spectroscopy. Concentration profiles, along and across the filaments, revealed that B, C and N are not homogeneously distributed within the nanostructures but are separated into pure C and BN domains. Interestingly, pure h-BN layers are always sandwiched between graphite-like shells. A two-stage growth process is proposed involving: (a) initial extrusion of a pure carbon filament from the catalytic particle, followed by (b) subsequent thickening of the BN and C layers precipitated from the gas phase. This pyrolytic technique provides an alternative and efficient route to segregated BN/C nanomaterials, which may prove useful as robust nanocomposites and semiconductor nanodevices with enhanced resistance towards oxidation.

  17. Generation of Triple-Transgenic Forsythia Cell Cultures as a Platform for the Efficient, Stable, and Sustainable Production of Lignans.

    Science.gov (United States)

    Murata, Jun; Matsumoto, Erika; Morimoto, Kinuyo; Koyama, Tomotsugu; Satake, Honoo

    2015-01-01

    Sesamin is a furofuran lignan biosynthesized from the precursor lignan pinoresinol specifically in sesame seeds. This lignan is shown to exhibit anti-hypertensive activity, protect the liver from damages by ethanol and lipid oxidation, and reduce lung tumor growth. Despite rapidly elevating demand, plant sources of lignans are frequently limited because of the high cost of locating and collecting plants. Indeed, the acquisition of sesamin exclusively depends on the conventional extraction of particular Sesamum seeds. In this study, we have created the efficient, stable and sustainable sesamin production system using triple-transgenic Forsythia koreana cell suspension cultures, U18i-CPi-Fk. These transgenic cell cultures were generated by stably introducing an RNAi sequence against the pinoresinol-glucosylating enzyme, UGT71A18, into existing CPi-Fk cells, which had been created by introducing Sesamum indicum sesamin synthase (CYP81Q1) and an RNA interference (RNAi) sequence against pinoresinol/lariciresinol reductase (PLR) into F. koreanna cells. Compared to its transgenic prototype, U18i-CPi-Fk displayed 5-fold higher production of pinoresinol aglycone and 1.4-fold higher production of sesamin, respectively, while the wildtype cannot produce sesamin due to a lack of any intrinsic sesamin synthase. Moreover, red LED irradiation of U18i-CPi-Fk specifically resulted in 3.0-fold greater production in both pinoresinol aglycone and sesamin than production of these lignans under the dark condition, whereas pinoresinol production was decreased in the wildtype under red LED. Moreover, we developed a procedure for sodium alginate-based long-term storage of U18i-CPi-Fk in liquid nitrogen. Production of sesamin in U18i-CPi-Fk re-thawed after six-month cryopreservation was equivalent to that of non-cryopreserved U18i-CPi-Fk. These data warrant on-demand production of sesamin anytime and anywhere. Collectively, the present study provides evidence that U18i-CP-Fk is an

  18. Radiolytic oxidation of propane: Computer modeling of the reaction scheme

    Science.gov (United States)

    Gupta, Avinash K.; Hanrahan, Robert J.

    The oxidation of gaseous propane under gamma radiolysis was studied at 100 torr pressure and 25°C, at oxygen pressures from 1 to 15 torr. Major oxygen-containing products and their G-values with 10% added oxygen are as follows: acetone, 0.98; i-propyl alcohol, 0.86; propionaldehyde, 0.43; n-propyl alcohol, 0.11; acrolein, 0.14; and allyl alcohol, 0.038. Minor products include i-butyl alcohol, t-amyl alcohol, n-butyl alcohol, n-amyl alcohol, and i-amyl alcohol. Small yields of i-hexyl alcohol and n-hexyl alcohol were also observed. There was no apparent difference in the G-values at pressures of 50, 100 and 150 torr. When the oxygen concentration was decreased below 5%, the yields of acetone, i-propyl alcohol, and n-propyl alcohol increased, the propionaldehyde yield decreased, and the yields of other products remained constant. The formation of major oxygen-containing products was explained on the basis that the alkyl radicals combine with molecular oxygen to give peroxyl radicals; the peroxyl radicals react with one another to give alkoxyl radicals, which in turn react with one another to form carbonyl compounds and alcohols. The reaction scheme for the formation of major products was examined using computer modeling based on a mechanism involving 28 reactions. Yields could be brought into agreement with the data within experimental error in nearly all cases.

  19. Stable bio-oil production from proteinaceous cyanobacteria: tail gas reactive pyrolysis of spirulina

    Science.gov (United States)

    Pyrolysis of Spirulina, a cyanobacteria with high levels of protein (74 wt %) and low levels of lipid (0.8 wt %) content, has the potential to produce fuels and platform chemicals that differ from those produced from lignocellulosic materials. The yields and product distribution from fluidized-bed p...

  20. Radiolytic oxidation of propane: computer modeling of the reaction scheme

    International Nuclear Information System (INIS)

    Gupta, A.K.; Hanrahan, R.J.

    1991-01-01

    The oxidation of gaseous propane under gamma radiolysis was studied at 100 torr pressure and 25 o C, at oxygen pressures from 1 to 15 torr. Major oxygen-containing products and their G-values with 10% added oxygen are as follows: acetone, 0.98; i-propyl alcohol, 0.86; propionaldehyde, 0.43; n-propyl alcohol, 0.11; acrolein, 0.14; and allyl alcohol, 0.038. The formation of major oxygen-containing products was explained on the basis that the alkyl radicals combine with molecular oxygen to give peroxyl radicals; the peroxyl radicals react with one another to give alkoxyl radicals, which in turn react with one another to form carbonyl compounds and alcohols. The reaction scheme for the formation of major products was examined using computer modeling based on a mechanism involving 28 reactions. Yields could be brought into agreement with the data within experimental error in nearly all cases. (author)

  1. Consuming algal products: trophic interactions of bacteria and a diatom species determined by RNA stable isotope probing

    Science.gov (United States)

    Sapp, Melanie; Gerdts, Gunnar; Wellinger, Marco; Wichels, Antje

    2008-09-01

    Heterotrophic marine bacteria utilise a wide range of carbon sources. Recently, techniques were developed to link bacterial identity and physiological capacity of microorganisms within natural communities. One of these methods is stable isotope probing (SIP) which allows an identification of active microorganisms using particular growth substrates. In this study, we present the first attempt to analyse bacterial communities associated with microalgae by rRNA-SIP. This approach was used to analyse bacterial populations consuming algal products of Thalassiosira rotula by applying SIP followed by reverse transcription of 16S rRNA and denaturing gradient gel electrophoresis. Generally, our results indicate that bacteria which consume algal products can be detected by isotope arrays coupled with fingerprinting methods.

  2. Enhanced Production and Characterization of a Solvent Stable Amylase from Solvent Tolerant Bacillus tequilensis RG-01: Thermostable and Surfactant Resistant

    Directory of Open Access Journals (Sweden)

    Soni Tiwari

    2014-01-01

    Full Text Available Ten bacterial strains isolated from the soil samples in the presence of cyclohexane were screened for amylase production. Among them, culture RG-01 was adjudged as the best amylase producer and was identified as Bacillus tequilensis from MTCC, Chandigarh. The isolate showed maximum amylase production (8100 U/mL in the presence of starch, peptone, and Ca2+ ions at 55°C pH 7.0 within 24 h of incubation. The enzyme was stable in the presence of n-dodecane, isooctane, n-decane, xylene, toluene, n-hexane, n-butanol, and cyclohexane, respectively. The presence of benzene, methanol, and ethanol marginally reduced the amylase stability, respectively. The enzyme was showed it 100% activity at 55°C and pH 7.0 with 119% and 127% stability at 55°C and pH 7.0, respectively. The enzyme was also stable in the presence of SDS, Tween-40, Tween-60, and Tween-80 (1% and was found stimulatory effect, respectively. Only Triton-X-100 showed a moderate inhibitory effect (5% on amylase activity. This isolate (Bacillus tequilensis RG-01 may be useful in several industrial applications owing to its thermotolerant and organic solvents and surfactants resistance characteristics.

  3. Enhanced production and characterization of a solvent stable amylase from solvent tolerant Bacillus tequilensis RG-01: thermostable and surfactant resistant.

    Science.gov (United States)

    Tiwari, Soni; Shukla, Neha; Mishra, Pooja; Gaur, Rajeeva

    2014-01-01

    Ten bacterial strains isolated from the soil samples in the presence of cyclohexane were screened for amylase production. Among them, culture RG-01 was adjudged as the best amylase producer and was identified as Bacillus tequilensis from MTCC, Chandigarh. The isolate showed maximum amylase production (8100 U/mL) in the presence of starch, peptone, and Ca(2+) ions at 55°C pH 7.0 within 24 h of incubation. The enzyme was stable in the presence of n-dodecane, isooctane, n-decane, xylene, toluene, n-hexane, n-butanol, and cyclohexane, respectively. The presence of benzene, methanol, and ethanol marginally reduced the amylase stability, respectively. The enzyme was showed it 100% activity at 55°C and pH 7.0 with 119% and 127% stability at 55°C and pH 7.0, respectively. The enzyme was also stable in the presence of SDS, Tween-40, Tween-60, and Tween-80 (1%) and was found stimulatory effect, respectively. Only Triton-X-100 showed a moderate inhibitory effect (5%) on amylase activity. This isolate (Bacillus tequilensis RG-01) may be useful in several industrial applications owing to its thermotolerant and organic solvents and surfactants resistance characteristics.

  4. Optimizing cropland cover for stable food production in Sub-Saharan Africa using simulated yield and Modern Portfolio Theory

    Science.gov (United States)

    Bodin, P.; Olin, S.; Pugh, T. A. M.; Arneth, A.

    2014-12-01

    Food security can be defined as stable access to food of good nutritional quality. In Sub Saharan Africa access to food is strongly linked to local food production and the capacity to generate enough calories to sustain the local population. Therefore it is important in these regions to generate not only sufficiently high yields but also to reduce interannual variability in food production. Traditionally, climate impact simulation studies have focused on factors that underlie maximum productivity ignoring the variability in yield. By using Modern Portfolio Theory, a method stemming from economics, we here calculate optimum current and future crop selection that maintain current yield while minimizing variance, vs. maintaining variance while maximizing yield. Based on simulated yield using the LPJ-GUESS dynamic vegetation model, the results show that current cropland distribution for many crops is close to these optimum distributions. Even so, the optimizations displayed substantial potential to either increase food production and/or to decrease its variance regionally. Our approach can also be seen as a method to create future scenarios for the sown areas of crops in regions where local food production is important for food security.

  5. Production of ammonium sulfate doubly labeled with the 15N and 34S stable isotopes

    International Nuclear Information System (INIS)

    Maximo, Everaldo; Bendassolli, Jose Albertino; Trivelin, Paulo Cesar Ocheuze; Rossete, Alexssandra Luiza Rodrigues Molina; Oliveira, Claudineia Raquel de; Prestes, Clelber Vieira

    2005-01-01

    The purpose of this work was the production of ammonium sulfate double labeled with 15 N and 34 S ((15NH 4 ) 2 34 SO 4 )), employing the ion exchange technique in two different processes. The first one was carried out using Na 2 34 SO 4 and ( 15 NH 4 ) 2 SO 4 previously enriched. It was possible to obtain about 54g of ( 15 NH 4 ) 2 34 SO 4 from 70.0g of Na 2 34 SO 4 and 64.2g of ( 15 NH 4 ) 2 SO 4 . The second method involved the production of H 2 34 SO 4 , by ion exchange, and its subsequent reaction with 15 NH 3(aq) , using a distillation system, to yield 58 g of ( 15 NH 4 ) 2 34 SO 4 from 43.1 g of H 2 34 SO 4 . (author)

  6. Copper Oxide Nanograss for Efficient and Stable Photoelectrochemical Hydrogen Production by Water Splitting

    Science.gov (United States)

    Borkar, Rajnikant; Dahake, Rashmi; Rayalu, Sadhana; Bansiwal, Amit

    2018-03-01

    A biphasic copper oxide thin film of grass-like appendage morphology is synthesized by two-step electro-deposition method and later investigated for photoelectrochemical (PEC) water splitting for hydrogen production. Further, the thin film was characterized by UV-Visible spectroscopy, x-ray diffraction (XRD), Scanning electron microscopy (SEM) and PEC techniques. The XRD analysis confirms formation of biphasic copper oxide phases, and SEM reveals high surface area grass appendage-like morphology. These grass appendage structures exhibit a high cathodic photocurrent of - 1.44 mAcm-2 at an applied bias of - 0.7 (versus Ag/AgCl) resulting in incident to photon current efficiency (IPCE) of ˜ 10% at 400 nm. The improved light harvesting and charge transport properties of grass appendage structured biphasic copper oxides makes it a potential candidate for PEC water splitting for hydrogen production.

  7. Shelf Stable Egg-Based Products Processed By Ultra High Pressure Technology

    Science.gov (United States)

    2008-07-03

    injected with steam/air mixtures can help make the process shorter by decreasing come up time, and can eventually yield products with improved texture and...isolated from ropy bread , was kindly provided by M. Gänzle (Lehrstuhl für Technische Mikrobiologie, Technische Universität München, Freising, Germany...The bacterium was grown aerobically at 32 C for 24 h in Trypticase soy broth supplemented with 0.1% yeast extract (Difco, Becton Dickinson, Sparks

  8. A synthetic, light-driven consortium of cyanobacteria and heterotrophic bacteria enables stable polyhydroxybutyrate production.

    Science.gov (United States)

    Weiss, Taylor L; Young, Eric J; Ducat, Daniel C

    2017-11-01

    We previously reported that Synechococcus elongatus PCC 7942, engineered with the sucrose transporter CscB, can export up to 85% of its photosynthetically-fixed carbon as sucrose and shows considerable promise as an alternative carbohydrate source. One approach to effectively utilize this cyanobacterium is to generate synthetic, light-driven consortia in which sucrose-metabolizing heterotrophs catalyze the conversion of the low-value carbohydrate into higher-value compounds in co-culture. Here, we report an improved synthetic photoautotroph/chemoheterotroph consortial design in which sucrose secreted by S. elongatus CscB directly supports the bacterium Halomonas boliviensis, a natural producer of the bioplastic precursor, PHB. We show that alginate encapsulation of S. elongatus CscB enhances sucrose-export rates ~2-fold within 66h, to ~290mg sucrose L -1 d -1 OD 750 -1 and enhances the co-culture stability. Consortial H. boliviensis accumulate up to 31% of their dry-weight as PHB, reaching productivities up to 28.3mg PHB L -1 d -1 . This light-driven, alginate-partitioned co-culture platform achieves PHB productivities that match or exceed those of traditionally engineered cyanobacterial monocultures. Importantly, S. elongatus CscB/H. boliviensis co-cultures were continuously productive for over 5 months and resisted invasive microbial species without the application of antibiotics or other chemical selection agents. Copyright © 2017 International Metabolic Engineering Society. Published by Elsevier Inc. All rights reserved.

  9. Stable and High Ajmalicine or Serpentine Production of Gamma Radiation Induction Mutant Catharantus Roseus

    International Nuclear Information System (INIS)

    Sumaryati Syukur

    2004-01-01

    Catharantus roseus Mutant have been selected by gamma irradiation with 20 krad doses of radiation and characterized as biochemical mutant with anti-feed back inhibition mechanism of tritophan decarboxylase (TDR) enzyme in biosynthetic path way of indole alkaloid. Production of indole alkaloid mainly ajmalicine with high economical values as a pharmaceutical drug for heart attack have been studied by using cell suspension cultures with several variation of medium, elicitors and stress osmosis. This treatment produced variation of indole alkaloid ajmalicine and serpentine. Several induction methods using Murashige and Skoog (MS) medium and polyethylene glycol PEG (6000) 1 to 7%, with hormones concentration of 2,4-D and kinetin as (10 : 1), showed optimal results of ajmalicine range between 20 and 50 nmol/gFW, and serpentine 10 to 60 nmol/gFW. This production increases ten time in mutant (20 Krad) by stress osmotic condition and performed long term stability in culture without subculture. In this paper explanation in detail about the selection methods, stability of mutant and the production of indole alkaloid ajmalicine and serpentine during growth phase, such as adaptation, log, and stationar in suspention culture of mutan cells. (author)

  10. Changes in porosity of graphite caused by radiolytic gasification by carbon dioxide

    International Nuclear Information System (INIS)

    Murdie, Neil; Edwards, I.A.S.; Marsh, Harry

    1986-01-01

    Methods have been developed to study porosity in nuclear grade graphite. The changes induced during the radiolytic gasification of graphite in carbon dioxide have been investigated. Porosity in radiolytically gasified graphite (0-22.8% wt. loss) was examined by optical microscopy and scanning electron microscopy (SEM). Each sample was vacuum impregnated with a slow-setting resin containing a fluorescent dye. Optical microscopy was used to study pores >2 μm 2 c.s.a. A semi-automatic image analysis system linked to the optical microscope enabled pore parameter data including cross-sectional areas, perimeters, Feret's diameters and shape factors, to be collected. The results showed that radiolytic gasification produced a large increase in the number of pores 2 c.s.a. New open pores 2 c.s.a. were developed by gasification of existing open porosity into the closed porosity ( 2 c.s.a.) within the binder-coke. Open pores, 2-100 μm 2 c.s.a., which were gasified within the coarse-grained mosaics of the binder-coke. In the gasification process to 22.8% wt. loss, the apparent open pore volume increased from 6.6 to 33.8% and the apparent closed pore volumes decreased from approx. 3% to 0.1%. The increase in apparent open porosity from 6.6% (virgin) to 33.8% resulted from gasification within original open porosity and by the opening and development of closed porosity. There was no evidence for creation of porosity from within the 'bulk' graphite, it being developed from existing fine porosity. The structure of pores > 100 μm 2 c.s.a. showed no change because of the inhibition of oxidation by deposition of carbonaceous species from the CH 4 inhibitor. Such species diffuse to the pore wall and are sacrificially oxidised. (author)

  11. Radiolytic degradation of hexabromocyclododecane in waste water from thermal insulation-treatment factory with gamma ray irradiation

    International Nuclear Information System (INIS)

    Wu, Xing-Zheng; Toriyama, Keisuke; Harii, Tomoaki; Katoh, Yoshio; Taniguchi, Tetsuo

    2008-01-01

    Radiolytic, and radiolytic/biological decompositions of hexabromocyclododecane (HBCD) in primary and ultimate waste waters from a thermal insulation-treatment process and a factory of polyester process are studied with gamma ray irradiation. Concentrations and degradation ratios of HBCD, and Br - concentrations are determined before and after gamma ray irradiation. Also, total organic carbon (TOC), chemical oxygen demand (COD), and biochemical oxygen demand (BOD) are determined to evaluate the decomposition of total organic compounds. As a result, about 72.5% of HBCD in ultimate waste water were decomposed with dose of 100 kGy. Furthermore, about 98% of HBCD, nearly all organic compounds were removed after the combination of radiolytic/biological treatments. (author)

  12. Downstream process for production of a viable and stable Bacillus cereus aquaculture biological agent

    CSIR Research Space (South Africa)

    Lalloo, R

    2010-03-01

    Full Text Available , rapid mixing providing near 441isothermal conditions and uniform end product (Bayrock 442and Ingledew 1997; Larena et al. 2003; Q1Luna-Solano et al. 4432005; Mille et al. 2004). 444The high recovery of B. cereus spores through our 445agglomeration... Biotechnol JrnlID 253_ArtID 2294_Proof# 1 - 13/10/2009 AUTHOR'S PROOF! UNCORRECTE D PROO F AUTHOR QUERY AUTHOR PLEASE ANSWER QUERY. Q1. Luna-Solano et al. 2005 was cited in the body but not listed in the reference list. Please provide complete...

  13. Stable production of the antimalarial drug artemisinin in the moss Physcomitrella patens

    DEFF Research Database (Denmark)

    Binti Khairul Ikram, Nur Kusaira; Kashkooli, Arman Beyraghdar; Peramuna, Anantha Vithakshana

    2017-01-01

    Malaria is a real and constant danger to nearly half of the world’s population of 7.4 billion people. In 2015, 212 million cases were reported along with 429,000 estimated deaths. The World Health Organization recommends Artemisinin-based Combinatorial Therapies (ACTs), and the artemisinin...... for this purpose is mainly isolated from the plant Artemisia annua. However, the plant supply of artemisinin is irregular, leading to fluctuation in prices. Here we report the development of a simple, sustainable, and scalable production platform of artemisinin. The five genes involved in artemisinin biosynthesis...

  14. Stable carbon isotopes in high-productive littoral areas of Lake Constance

    International Nuclear Information System (INIS)

    Chondrogianni, C.

    1992-01-01

    The investigation attempted to extend understanding of C fractionation in aquatic systems and to facilitate the interpretation of palaeolimnological isotope data. Particular interest was taken in the aspect of bicarbonate assimilation at high productivity and in the exchange processes between water and atmosphere. Littoral areas of lakes were chosen as areas of investigation as they offer a high-productivity environment with large populations of submersed macrophytes and periphytes. To get a better picture of the factors influencing C fractionation, litteral and pellagial regions were compared on the one hand and a mesotrophic (Ueberlingersee) and a eutrophic (Gnadensee) lake section on the other hand. Further factors of differentiation between the two lake parts were: Volume, the proportional share of the litteral area, and water exchange. Two main fields of interest were investigated: - Determination of the C isotope ratio (δ 13 C) in the dissolved bicarbonate of water in the sediments of a single year for the purpose of calibrating its fractionation in the basis of the present chemical and physical status of the lake water (water programme). - Determination of δ 13 C in selected carbonate components from sedimentary cores in order to find out about palaeolimnological events in the areas of investigation (sediment programme). (orig.) [de

  15. Iron hexacyanide/cytochrome-C - intramolecular electron transfer and binding constants - (pulse radiolytic study). Progress report

    International Nuclear Information System (INIS)

    Ilan, Y.; Shafferman, A.

    Internal oxidation and reduction rates of horse cytochrome-c in the complexes, CII.Fe/sup III/(CN) -3 6 and CIII.Fe/sup II/(CN) -4 6 , are 4.6.10 4 s -1 and 3.3.10 2 s -1 , respectively. The binding sites of the iron hexacyanide ions on either CII or CIII are kinetically almost indistinguishable; binding constants range from 0.87.10 3 to 2.10 3 M -1 . The present pulse radiolytic kinetic data are compared with that from N.M.R, T-jump and equilibrium dialysis studies

  16. The radiolytic cracking decomposion of the plant cellulose materials and their chemcial properties

    International Nuclear Information System (INIS)

    Shou Hongxia

    1987-01-01

    Under the treatment with high energy radiation, plant cellulose materials undergo a series of changes in chemical and physical properties. This paper describes the chemical changes of water-soluble carbohydrate, easy-to-hydrolyse carbohydrate, hard-to-hydrolyse carbohydrate, amino acid and protein in rice straw after irradiation with 60 Co γ-ray. The content of water-soluble carbohydrate in rice straw can be increased significantly by such treatment. The combination treatment of irradiation and acid or alkali soaker can reduce the dose for the radiolytic cracking decomposition and produce a good effect

  17. Radiolytic gas generation from cement-based waste hosts for DOE low-level radioactive wastes

    International Nuclear Information System (INIS)

    Dole, L.R.; Friedman, H.A.

    1986-01-01

    Using cement-based immobilization binders with simulated radioactive waste containing sulfate, nitrate, nitrite, phosphate, and fluoride anions, the gamma- and alpha-radiolytic gas generation factors (G/sub t/, molecules/100 eV) and gas compositions were measured on specimens of cured grouts. These tests studied the effects of; (1) waste composition; (2) the sample surface-to-volume ratio; (3) the waste slurry particle size; and (4) the water content of the waste host formula. The radiolysis test vessels were designed to minimize the ''dead'' volume and to simulate the configuration of waste packages

  18. Partitioning of evapotranspiration using a stable isotope technique in an arid and high temperature agricultural production system

    KAUST Repository

    Lu, Xuefei

    2016-08-22

    Agricultural production in the hot and arid low desert systems of southern California relies heavily on irrigation. A better understanding of how much and to what extent irrigated water is transpired by crops relative to being lost through evaporation would improve the management of increasingly limited water resources. In this study, we examined the partitioning of evapotranspiration (ET) over a field of forage sorghum (Sorghum bicolor), which was under evaluation as a potential biofuel feedstock, based on isotope measurements of three irrigation cycles at the vegetative stage. This study employed customized transparent chambers coupled with a laser-based isotope analyzer to continuously measure near-surface variations in the stable isotopic composition of evaporation (E, δ), transpiration (T, δ) and ET (δ) to partition the total water flux. Due to the extreme heat and aridity, δ and δ were very similar, which makes this system highly unusual. Contrary to an expectation that the isotopic signatures of T, E, and ET would become increasingly enriched as soils became drier, our results showed an interesting pattern that δ, δ, and δ increased initially as soil water was depleted following irrigation, but decreased with further soil drying in mid to late irrigation cycle. These changes are likely caused by root water transport from deeper to shallower soil layers. Results indicate that about 46% of the irrigated water delivered to the crop was used as transpiration, with 54% lost as direct evaporation. This implies that 28 − 39% of the total source water was used by the crop, considering the typical 60 − 85% efficiency of flood irrigation. The stable isotope technique provided an effective means of determining surface partitioning of irrigation water in this unusually harsh production environment. The results suggest the potential to further minimize unproductive water losses in these production systems.

  19. Radiolytic corrosion of uranium dioxide induced by He{sup 2+} localized irradiation of water: Role of the produced H{sub 2}O{sub 2} distance

    Energy Technology Data Exchange (ETDEWEB)

    Traboulsi, Ali [SUBATECH, UMR 6457, Ecole des Mines de Nantes, CNRS/IN2P3, Université de Nantes, 4, Rue Alfred Kastler, La Chantrerie BP 20722, 44307 Nantes Cedex 3 (France); Vandenborre, Johan, E-mail: johan.vandenborre@subatech.in2p3.fr [SUBATECH, UMR 6457, Ecole des Mines de Nantes, CNRS/IN2P3, Université de Nantes, 4, Rue Alfred Kastler, La Chantrerie BP 20722, 44307 Nantes Cedex 3 (France); Blain, Guillaume [SUBATECH, UMR 6457, Ecole des Mines de Nantes, CNRS/IN2P3, Université de Nantes, 4, Rue Alfred Kastler, La Chantrerie BP 20722, 44307 Nantes Cedex 3 (France); Humbert, Bernard [Institut de Matériaux Jean Rouxel, UMR 6502, Université de Nantes – CNRS, 2 rue de la Houssinnière, BP 32229, 44340 Nantes (France); Haddad, Ferid [SUBATECH, UMR 6457, Ecole des Mines de Nantes, CNRS/IN2P3, Université de Nantes, 4, Rue Alfred Kastler, La Chantrerie BP 20722, 44307 Nantes Cedex 3 (France); Cyclotron Arronax, 1 rue Arronax, CS 10112, 44817 Saint Herblain Cedex (France); Fattahi, Massoud [SUBATECH, UMR 6457, Ecole des Mines de Nantes, CNRS/IN2P3, Université de Nantes, 4, Rue Alfred Kastler, La Chantrerie BP 20722, 44307 Nantes Cedex 3 (France)

    2015-12-15

    The short-range (few μm in water) of the α-emitting from the spent fuel involves that the radiolytic corrosion of this kind of sample occurs at the solid/solution interface. In order to establish the role of localization of H{sub 2}O{sub 2} species produced by the He{sup 2+} particle beam in water from the surface, we perform UO{sub 2} radiolytic corrosion experiment with different distance between H{sub 2}O{sub 2} production area and UO{sub 2} surface. Then, in this work, the radiolytic corrosion of UO{sub 2} particles by oxidative species produced by {sup 4}He{sup 2+} radiolysis of water was investigated in open to air atmosphere. The dose rate, the localization of H{sub 2}O{sub 2} produced by water radiolysis and the grain boundaries present on the surface of the particles were investigated. UO{sub 2} corrosion was investigated by in situ (during irradiation) characterization of the solid surface, analysis of H{sub 2}O{sub 2} produced by water radiolysis and quantification of the uranium species released into the solution during irradiation. Characterization of the UO{sub 2} particles, surface and volume, was realized by Raman spectroscopy. UV–vis spectrophotometry was used to monitor H{sub 2}O{sub 2} produced by water radiolysis and in parallel the soluble uranium species released into the solution were quantified by inductively coupled plasma mass spectrometry. During the He{sup 2+} irradiation of ultra-pure water in contact with the UO{sub 2} particles, metastudtite phase was formed on the solid surface indicating an oxidation process of the particles by the oxidative species produced by water radiolysis. This oxidation occurred essentially on the grain boundaries and was accompanied by migration of soluble uranium species (U(VI)) into the irradiated solution. Closer to the surface the localization of H{sub 2}O{sub 2} formation, higher the UO{sub 2} oxidation process occurs, whereas the dose rate had no effect on it. Simultaneously, closer to the surface

  20. Optimized production and characterization of a detergent-stable protease from Lysinibacillus fusiformis C250R.

    Science.gov (United States)

    Mechri, Sondes; Kriaa, Mouna; Ben Elhoul Berrouina, Mouna; Omrane Benmrad, Maroua; Zaraî Jaouadi, Nadia; Rekik, Hatem; Bouacem, Khelifa; Bouanane-Darenfed, Amel; Chebbi, Alif; Sayadi, Sami; Chamkha, Mohamed; Bejar, Samir; Jaouadi, Bassem

    2017-08-01

    In this study, we aimed to optimize the cultural and nutritional conditions for protease production by Lysinibacillus fusiformis strain C250R in submerged fermentation process using statistical methodology. The most significant factors (gruel, wheat bran, yeast extract, and FeSO 4 ) were identified by Plackett-Burman design. Response surface methodology (RSM) was used to determine the optimum levels of the screened factors and their interaction. Under the optimized conditions, protease yield 3100U/mL was 4.5 folds higher than those obtained by the use of the initial conditions (680U/mL). Additionally, a new extracellular 51kDa-protease, designated SAPLF, was purified and biochemically characterized from strain C250R. It shows optimum activity at 70°C and pH 10. Its half-life times at 70 and 80°C were 10 and 6-h, respectively. Irreversible inhibition of enzyme activity of SAPLF with serine protease inhibitors demonstrated that it belongs to the serine protease family. Interestingly, its catalytic efficiency was higher than that of SPVP from Aeribacillus pallidus strain VP3 and Alcalase Ultra 2.5L from Bacillus licheniformis. This study demonstrated that SAPLF has a high detergent compatibility and an excellent stain removal compared to Alcalase Ultra 2.5L; which offers an interesting potential for its application in the laundry detergent industry. Copyright © 2017 Elsevier B.V. All rights reserved.

  1. Radiolytic gas generation in plutonium contaminated waste materials

    International Nuclear Information System (INIS)

    Kazanjian, A.R.

    1976-01-01

    Many plutonium contaminated waste materials decompose into gaseous products because of exposure to alpha radiation. The gases generated (usually hydrogen) over long-storage periods may create hazardous conditions. To determine the extent of such hazards, knowing the gas generation yields is necessary. These yields were measured by contacting some common Rocky Flats Plant waste materials with plutonium and monitoring the enclosed atmospheres for extensive periods of time. The materials were Plexiglas, polyvinyl chloride, glove-box gloves, machining oil, carbon tetrachloride, chlorothene VG solvent, Kimwipes (dry and wet), polyethylene, Dowex-1 resin, and surgeon's gloves. Both 239 Pu oxide and 238 Pu oxide were used as radiation sources. The gas analyses were made by mass spectrometry and the results obtained were the total gas generation, the hydrogen generation, the oxygen consumption rate, and the gas composition over the entire storage period. Hydrogen was the major gas produced in most of the materials. The total gas yields varied from 0.71 to 16 cm 3 (standard temperature pressure) per day per curie of plutonium. The oxygen consumption rates varied from 0.0088 to 0.070 millimoles per day per gram of plutonium oxide-239 and from 0.0014 to 0.0051 millimoles per day per milligram 238 Pu

  2. Estimation of pathways of the production of greenhouse gases in the tropical swamp forest in Thailand by stable isotope investigation.

    Science.gov (United States)

    Boontanon, Narin; Ueda, Shingo; Wada, Eitaro

    2008-09-01

    Dynamics of greenhouse gases (N(2)O and CH(4)) with the dry-wet cycle along with the variation of oxidation-reduction boundaries were investigated in the tropical wetland in monsoon Asia. It was clarified that the production of N(2)O and CH(4) was closely related to the development of a redox boundary in the Bang Nara River systems. An intermittent increase in N(2)O was observed at the beginning of the rainy season, when a large amount of easily decomposable organic matter was introduced into the river. After 10 days, when dissolved oxygen was consumed completely at the middle reaches, the emission of CH(4) became maximal due to the possible occurrence of denitrification. The distribution of stable isotope ratios in N(2)O clearly demonstrated that nitrification is the major process for its production. Furthermore, the production of N(2)O in this study area was found to vary in time and space with changes in the redox boundary along the water flow.

  3. Radiolytic formation of organic iodides from organic compounds released from ripolin paint

    International Nuclear Information System (INIS)

    Attia, S.; Evans, G.J.

    2002-01-01

    The impact of a serious nuclear reactor accident is governed to a large extent by the possible release of airborne organic iodides to the environment. This research examines the identification and behavior of organic iodides formed in the containment due to the release of organic compounds from Ripolin paint, into the aqueous phase, following a nuclear reactor accident. A bench scale apparatus installed in the irradiation chamber of a Gammacell was used to analyze the formation of organic iodides. Iodo-organics, transferred to the gas phase above irradiated aqueous samples, were analyzed using a Thermal Desorption method coupled with gas chromatography and mass spectrometry. Detailed studies of the identity of the organic compounds released and the organic iodides formed were conducted. The effects of parameters such as irradiation dose were also examined. All the organic iodides formed, under radiolytic conditions, were identified as iodo-alkanes. The organic compounds that were released from the Ripolin paint, such as methyl isobutyl ketone, were found to decompose, by a series of reactions, to produce the organic iodides. The precursor organic compounds and the organic iodides formed were observed to consist of the same alkyl group. These results indicate that organic compounds released from surface paints directly influence the formation of radiolytic organic iodide. (author)

  4. The importance of variables and parameters in radiolytic chemical kinetics modeling

    International Nuclear Information System (INIS)

    Piepho, M.G.; Turner, P.J.; Reimus, P.W.

    1988-07-01

    Many pertinent radiochemical reactions are not completely understood, and most of the associated rate constants are poorly characterized. To help identify the important radiochemical reactions, rate constants, species, and environmental conditions, an importance theory code, SWATS (Sensitivity With Adjoint Theory-Sparse version)-LOOPCHEM, has been developed for the radiolytic chemical kinetics model in the radiolysis code LOOPCHEM. The LOOPCHEM code calculates the concentrations of various species in a radiolytic field over time. The SWATS-LOOPCHEM code efficiently calculates: (1) the importance (relative to a defined response of interest) of each species concentration over time, (2) the sensitivity of each parameter of interest, and (3) the importance of each equation in the radiolysis model. The calculated results will be used to guide future experimental and modeling work for determining the importance of radiolysis on waste package performance. A demonstration (the importance of selected concentrations and the sensitivities of selected parameters) of the SWATS-LOOPCHEM code is provided for illustrative purposes, and no attempt is made at this time to interpret the results for waste package performance assessment purposes. 12 refs., 1 fig., 1 tab

  5. Microbial Oxidation of Hg(0) - Its Effect on Hg Stable Isotope Fractionation and Methylmercury Production

    Energy Technology Data Exchange (ETDEWEB)

    Yee, Nathan [Rutgers Univ., New Brunswick, NJ (United States); Barkay, Tamar [Rutgers Univ., New Brunswick, NJ (United States); Reinfelder, John [Rutgers Univ., New Brunswick, NJ (United States)

    2016-06-28

    -dependent discrimination against 202Hg relative to 198Hg. G. sulfurreducens PCA and D. desulfuricans ND132 have similar kinetic reactant/product Hg fractionation factors. Using the Hg isotope data, we showed that there are multiple intra- and/or extracellular pools provide substrate inorganic Hg for methylation.

  6. Evaluation of Primary Production in the Lower Amazon River Based on a Dissolved Oxygen Stable Isotopic Mass Balance

    Energy Technology Data Exchange (ETDEWEB)

    Gagne-Maynard, William C.; Ward, Nicholas D.; Keil, Richard G.; Sawakuchi, Henrique O.; Da Cunha, Alan C.; Neu, Vania; Brito, Daimio C.; Da Silva Less, Diani F.; Diniz, Joel E. M.; De Matos Valerio, Aline; Kampel, Milton; Krusche, Alex V.; Richey, Jeffrey E.

    2017-02-07

    The Amazon River outgasses nearly an equivalent amount of CO2 as the rainforest sequesters on an annual basis due to microbial decomposition of terrigenous and aquatic organic matter. Most research performed in the Amazon has been focused on unraveling the mechanisms driving CO2 production since the recognition of a persistent state of CO2 supersaturation. However, although the river system is clearly net heterotrophic, the interplay between primary production and respiration is an essential aspect to understanding the overall metabolism of the ecosystem and potential transfer of energy up trophic levels. For example, an efficient ecosystem is capable of both decomposing high amounts of organic matter at lower trophic levels, driving CO2 emissions, and accumulating energy/biomass in higher trophic levels, stimulating fisheries production. Early studies found minimal evidence for primary production in the Amazon River mainstem and it has since been assumed that photosynthesis is strongly limited by low light penetration attributed to the high sediment load. Here, we test this assumption by measuring the stable isotopic composition of O218O-O2) and O2 saturation levels in the lower Amazon River from Óbidos to the river mouth and its major tributaries, the Xingu and Tapajós rivers, during high and low water periods. An oxygen mass balance model was developed to estimate the input of photosynthetic oxygen in the discrete reach from Óbidos to Almeirim, midway to the river mouth. Based on the oxygen mass balance we estimate that primary production occurred at a rate of 0.39 ± 0.24 g O m3 d-1 at high water and 1.02 ± 0.55 g O m3 d-1 at low water. This translates to 41 ± 24% of the rate of O2 drawdown via respiration during high water and 67 ± 33% during low water. These primary production rates are 2-7 times higher than

  7. Experimental determination and chemical modelling of radiolytic processes at the spent fuel/water interface. Experiments carried out in carbonate solutions in absence and presence of chloride

    Energy Technology Data Exchange (ETDEWEB)

    Bruno, Jordi; Cera, Esther; Grive, Mireia; Duro, Lara [Enviros Spain SL (Spain); Eriksen, Trygve [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear Chemistry

    2003-01-01

    We report on the recent experimental and modelling results of a research programme that started in 1995. The aim has been to understand the kinetic and thermodynamic processes that control the radiolytic generation of oxidants and reductants at the spent fuel water interface and their consequences for spent fuel matrix stability and radionuclide release. This has been done by carrying out well-controlled dissolution experiments of PWR Ringhals spent fuel fragments in an initially anoxic closed system and by using different solution compositions. Experimental series started with several tests carried out with deionised water as solvent, in a second phase experiments were conducted with 10 mM bicarbonate solutions. New experimental series were set up during the last two years by using the same bicarbonate content in solutions with varying NaCl concentrations in order to ascertain the role of this ligand on the radiolytic products and its consequence for radionuclide release. The selected NaCl concentrations are in the range of 0.1 to 10 mM. Experimental data shows that uranium dissolution at early contact times is controlled by the oxidation of the UO{sub 2} matrix. This process controls the co-dissolution of most of the analysed radionuclides, including Sr, Mo, Tc, Np and surprisingly enough, Cs. In the overall the release rates for U and the matrix associated radionuclides are in the range of 10{sup -6} moles/day with a clear decreasing trend with exposure time and after 2 years the initial release rates have decreased down to 3x10{sup -8} moles/day. The solubility of the released actinides appears to be limited by the formation of An(IV) hydroxide phases, although Np concentrations in solution did not reach solubility levels during the time intervals of the present tests. No secondary solid phase appears to control the solubility of the rest of the elements.

  8. Reactivity Of Radiolytically-Produced Nitrogen Oxide Radicals Toward Aromatic Compounds

    International Nuclear Information System (INIS)

    Elias, Gracy

    2010-01-01

    radiolysis of the modifier (Cs-7SB), which solvates both metal complexes, is responsible for this change. These reactions presumably occur due to reactions with radiolytically-produced nitrogen-centered radicals like (sm b ullet)NO, (sm b ullet)NO 2 and (sm b ullet)NO 3 . Anisole (C 6 H 5 -OCH 3 ) was used in this study as a surrogate for Cs-7SB, since both are aryl ethers. Toluene was used as a surrogate for Cs-7SB because of the alkyl group on the benzene ring in both molecules. Anisole, highly reactive in acids, is a small molecule compared to Cs-7SB and the nitration products are easier to identify compared to those for the larger Cs-7SB molecule. Toluene is less reactive than anisole. Therefore, the highly reactive anisole and the less reactive toluene were considered in this study as model compounds to compare the reaction mechanisms and the nitrated products in acidic media under irradiation. Experiments were designed to elucidate the mechanism of the nitration of aromatic rings in γ-irradiated aqueous nitric acid. Since a suite of radical and ionic reactive species are produced in this condensed-phase system, solutions of nitric acid, neutral nitrate and neutral nitrite were irradiated in separate experiments to isolate selected reactive species. Product nitration species were assessed by high performance liquid chromatography (HPLC) with a reversed phase C-18 column and photodiode array detector. The nitrated anisole product distributions were the same with and without radiation in acidic solution, although more products were formed with radiation. In the irradiated acidic condensed phase, radiation-enhanced nitrous acid-catalyzed nitrosonium ion electrophilic aromatic substitution followed by oxidation reactions dominated over radical addition reactions. In contrast, the distribution of nitrated derivatives for toluene showed nitronium ion electrophilic substitution in the unirradiated acidic medium as a result of thermal nitration only at elevated temperatures

  9. Combining UHPLC-High Resolution MS and Feeding of Stable Isotope Labeled Polyketide Intermediates for Linking Precursors to End Products

    DEFF Research Database (Denmark)

    Klitgaard, Andreas; Frandsen, Rasmus John Normand; Holm, Dorte Koefoed

    2015-01-01

    acid (6-MSA) and 13C14-YWA1, both produced in-house, as well as commercial 13C7-benzoic acid and 2H7-cinnamic acid, in species of Fusarium, Byssochlamys, Aspergillus, and Penicillium. Incorporation of 6-MSA into terreic acid or patulin was not observed in any of six evaluated species covering three...... genera, because the 6-MSA was shunted into (2Z,4E)-2-methyl-2,4-hexadienedioic acid. This indicates that patulin and terreic acid may be produced in a closed compartment of the cell and that (2Z,4E)-2-methyl-2,4-hexadienedioic acid is a detoxification product toward terreic acid and patulin. In Fusarium...... spp., YWA1 was shown to be incorporated into aurofusarin, rubrofusarin, and antibiotic Y. In A. niger, benzoic acid was shown to be incorporated into asperrubrol. Incorporation levels of 0.7–20% into the end-products were detected in wild-type strains. Thus, stable isotope labeling is a promising...

  10. Production of an {sup 15}O beam using a stable oxygen ion beam for in-beam PET imaging

    Energy Technology Data Exchange (ETDEWEB)

    Mohammadi, Akram, E-mail: mohammadi.akram@qst.go.jp; Yoshida, Eiji; Tashima, Hideaki; Nishikido, Fumihiko; Inaniwa, Taku; Kitagawa, Atsushi; Yamaya, Taiga

    2017-03-21

    In advanced ion therapy, the {sup 15}O ion beam is a promising candidate to treat hypoxic tumors and simultaneously monitor the delivered dose to a patient using PET imaging. This study aimed at production of an {sup 15}O beam by projectile fragmentation of a stable {sup 16}O beam in an optimal material, followed by in-beam PET imaging using a prototype OpenPET system, which was developed in the authors’ group. The study was carried out in three steps: selection of the optimal target based on the highest production rate of {sup 15}O fragments; experimental production of the beam using the optimal target in the Heavy Ion Medical Accelerator Chiba (HIMAC) secondary beam course; and realization of in-beam PET imaging for the produced beam. The optimal target evaluations were done using the Monte Carlo simulation code PHITS. The fluence and mean energy of the secondary particles were simulated and the optimal target was selected based on the production rate of {sup 15}O fragments. The highest production rate of {sup 15}O was observed for a liquid hydrogen target, 3.27% for a 53 cm thick target from the {sup 16}O beam of 430 MeV/u. Since liquid hydrogen is not practically applicable in the HIMAC secondary beam course a hydrogen-rich polyethylene material, which was the second optimal target from the simulation results, was selected as the experimental target. Three polyethylene targets with thicknesses of 5, 11 or 14 cm were used to produce the {sup 15}O beam without any degrader in the beam course. The highest production rate was measured as around 0.87% for the 11 cm thick polyethylene target from the {sup 16}O beam of 430 MeV/u when the angular acceptance and momentum acceptance were set at ±13 mrad and ±2.5%, respectively. The purity of the produced beam for the three targets were around 75%, insufficient for clinical application, but it was increased to 97% by inserting a wedge shape aluminum degrader with a thickness of 1.76 cm into the beam course and that is

  11. Production of an 15O beam using a stable oxygen ion beam for in-beam PET imaging

    Science.gov (United States)

    Mohammadi, Akram; Yoshida, Eiji; Tashima, Hideaki; Nishikido, Fumihiko; Inaniwa, Taku; Kitagawa, Atsushi; Yamaya, Taiga

    2017-03-01

    In advanced ion therapy, the 15O ion beam is a promising candidate to treat hypoxic tumors and simultaneously monitor the delivered dose to a patient using PET imaging. This study aimed at production of an 15O beam by projectile fragmentation of a stable 16O beam in an optimal material, followed by in-beam PET imaging using a prototype OpenPET system, which was developed in the authors' group. The study was carried out in three steps: selection of the optimal target based on the highest production rate of 15O fragments; experimental production of the beam using the optimal target in the Heavy Ion Medical Accelerator Chiba (HIMAC) secondary beam course; and realization of in-beam PET imaging for the produced beam. The optimal target evaluations were done using the Monte Carlo simulation code PHITS. The fluence and mean energy of the secondary particles were simulated and the optimal target was selected based on the production rate of 15O fragments. The highest production rate of 15O was observed for a liquid hydrogen target, 3.27% for a 53 cm thick target from the 16O beam of 430 MeV/u. Since liquid hydrogen is not practically applicable in the HIMAC secondary beam course a hydrogen-rich polyethylene material, which was the second optimal target from the simulation results, was selected as the experimental target. Three polyethylene targets with thicknesses of 5, 11 or 14 cm were used to produce the 15O beam without any degrader in the beam course. The highest production rate was measured as around 0.87% for the 11 cm thick polyethylene target from the 16O beam of 430 MeV/u when the angular acceptance and momentum acceptance were set at ±13 mrad and ±2.5%, respectively. The purity of the produced beam for the three targets were around 75%, insufficient for clinical application, but it was increased to 97% by inserting a wedge shape aluminum degrader with a thickness of 1.76 cm into the beam course and that is sufficiently high. In-beam PET imaging was also

  12. Sustainable production of syngas from biomass-derived glycerol by steam reforming over highly stable Ni/SiC.

    Science.gov (United States)

    Kim, Sung Min; Woo, Seong Ihl

    2012-08-01

    The production of syngas was investigated by steam reforming glycerol over Ni/Al(2)O(3), Ni/CeO(2), and Ni/SiC (which have acidic, basic, and neutral properties) at temperatures below 773 K. The complete and stable conversion of glycerol with a yield (higher than 90 %) of gaseous products (mainly syngas) was achieved over Ni/SiC during a 60 h reaction, whereas the conversion of glycerol continually decreases over Ni/Al(2)O(3) (by 49.8 %) and Ni/CeO(2) (by 77.1 %). The deactivation of Ni/Al(2)O(3) and Ni/CeO(2) is mainly caused by coke deposition because of the C-C cleavage of the byproducts produced by dehydration over acidic sites and condensation over basic sites. Gaseous products with a 1.0-1.9 syngas ratio (H(2)/CO) are produced over Ni/SiC. This ratio is required for the Fischer-Tropsch synthesis. However, a syngas ratio of more than 3.0 was observed over Ni/Al(2)O(3) and Ni/CeO(2) because of the high activity of the water-gas-shift reaction. Any dissociative or associative adsorption of water on Al(2)O(3) and CeO(2) promotes a water-gas-shift reaction and produces a higher syngas ratio. H(2) and CO were mainly produced by decomposition of glycerol through dehydrogenation and decarbonylation over Ni sites. Thus, SiC promotes an intrinsic contribution of nickel (dehydrogenation, and decarbonylation) without any byproducts from the dehydration and condensation. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  13. The radiolytic and chemical degradation of organic ion exchange resins under alkaline conditions: effect on radionuclide speciation

    International Nuclear Information System (INIS)

    Loon, L. van; Hummel, W.

    1995-10-01

    The formation of water soluble organic ligands by the radiolytic and chemical degradation of several ion exchange resins was investigated under conditions close to those of the near field of a cementitious repository. The most important degradation products were characterised and their role on radionuclide speciation evaluated thoroughly. Irradiation of strong acidic cation exchange resins (Powdex PCH and Lewatite S-100) resulted in the formation of mainly sulphate and dissolved organic carbon. A small part of the carbon (10-20%) could be identified as oxalate. The identity of the remainder is unknown. Complexation studies with Cu 2+ and Ni 2+ showed the presence of two ligands: oxalate and ligand X. Although ligand X could not be identified, it could be characterised by its concentration, a deprotonation constant and a complexation constant for the NiX complex. The influence of oxalate and ligand X on the speciation of radionuclides is examined in detail. For oxalate no significant influence on the speciation of radionuclides is expected. The stronger complexing ligand X may exert some influence depending on its concentration and the values of other parameters. These critical parameters are discussed and limiting values are evaluated. In absence of irradiation, no evidence for the formation of ligands was found. Irradiation of strong basic anion exchange resins (Powdex PAO and Lewatite M-500) resulted in the formation of mainly ammonia, amines and dissolved organic carbon. Up to 50% of the carbon could be identified as methyl-, dimethyl- and trimethylamine. Complexation studies with Eu 3+ showed that the complexing capacity under near field conditions was negligible. The speciation of cations such as Ag, Ni, Cu and Pd can be influenced by the presence of amins. The strongest amine-complexes are formed with Pd and therefore, as an example, the aqueous Pd-ammonia system is examined in great detail. (author) 30 figs., 10 tabs., refs

  14. The radiolytic and chemical degradation of organic ion exchange resins under alkaline conditions: effect on radionuclide speciation

    Energy Technology Data Exchange (ETDEWEB)

    Loon, L. van; Hummel, W. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1995-10-01

    The formation of water soluble organic ligands by the radiolytic and chemical degradation of several ion exchange resins was investigated under conditions close to those of the near field of a cementitious repository. The most important degradation products were characterised and their role on radionuclide speciation evaluated thoroughly. Irradiation of strong acidic cation exchange resins (Powdex PCH and Lewatite S-100) resulted in the formation of mainly sulphate and dissolved organic carbon. A small part of the carbon (10-20%) could be identified as oxalate. The identity of the remainder is unknown. Complexation studies with Cu{sup 2+} and Ni{sup 2+} showed the presence of two ligands: oxalate and ligand X. Although ligand X could not be identified, it could be characterised by its concentration, a deprotonation constant and a complexation constant for the NiX complex. The influence of oxalate and ligand X on the speciation of radionuclides is examined in detail. For oxalate no significant influence on the speciation of radionuclides is expected. The stronger complexing ligand X may exert some influence depending on its concentration and the values of other parameters. These critical parameters are discussed and limiting values are evaluated. In absence of irradiation, no evidence for the formation of ligands was found. Irradiation of strong basic anion exchange resins (Powdex PAO and Lewatite M-500) resulted in the formation of mainly ammonia, amines and dissolved organic carbon. Up to 50% of the carbon could be identified as methyl-, dimethyl- and trimethylamine. Complexation studies with Eu{sup 3+} showed that the complexing capacity under near field conditions was negligible. The speciation of cations such as Ag, Ni, Cu and Pd can be influenced by the presence of amins. The strongest amine-complexes are formed with Pd and therefore, as an example, the aqueous Pd-ammonia system is examined in great detail. (author) 30 figs., 10 tabs., refs.

  15. Role of eaq−, ·OH and H· in radiolytic degradation of atrazine: A kinetic and mechanistic approach

    International Nuclear Information System (INIS)

    Khan, Javed Ali; Shah, Noor S.; Nawaz, Shah; Ismail, M.; Rehman, Faiza; Khan, Hasan M.

    2015-01-01

    Highlights: • Atrazine was efficiently removed from aqueous solution by γ-ray irradiation. • e aq − was found to have more crucial role in removal of atrazine than ·OH. • Atrazine degradation was reduced in the presence of t-BuOH and i-PrOH. • Atrazine showed high stability at neutral pH than at very low and high pH conditions. • Potential degradation mechanism was evaluated by GC–MS analysis. - Abstract: The degradation of atrazine was investigated in aqueous solution by gamma-ray irradiation. 8.11 μM initial atrazine concentration could be completely removed in N 2 saturated solution by applying 3500 Gy radiation dose at a dose rate of 296 Gy h −1 . Significant removal of atrazine (i.e., 39.4%) was observed at an absorbed dose of 1184 Gy in air saturated solution and the removal efficiency was promoted to 50.5 and 65.4% in the presence of N 2 O and N 2 gases, respectively. The relative contributions of hydrated electron, hydroxyl radical and hydrogen radical toward atrazine degradation were determined as ratio of observed dose constant (k obs ) and found to be 5: 3: 1 for k eaq − : k ·OH : k H ·, respectively. The degradation efficiency of atrazine was 69.5, 55.6 and 37.3% at pH 12.1, 1.7 and 5.7, respectively. A degradation mechanism was proposed based on the identified degradation by-products by gas chromatography–mass spectrometry. Taking the relative contributions of oxidative and reductive species to atrazine degradation into account, reductive pathway proved to be a better approach for the radiolytic treatment of atrazine contaminated water

  16. Radiolytically-induced novel materials and their application to waste processing

    Energy Technology Data Exchange (ETDEWEB)

    Massimo Bertino, Akira Tokuhiro, Tadashi Tokuhiro

    2007-12-05

    In the present NEER project we investigated two different types of gel materials with respect to potential applications in environmental remediation, including mixed waste generated from the nuclear fuel cycles. The materials under study were: (1) silica-polymer based aerogel composites into which specific metallic cations diffuse into and remain, and (2) polymer gels made of thermo-sensitive polymer networks, whose functional groups can be ''tailored'' to have a preferred affinity for specific cations, again diffusing into and remaining in the network under a volumetrically, contractive phase-transition. The molecular, diffusion of specific cations, including those of concern in low-level waste streams, into the gel materials studied here indicates that a scaled, engineered system can be designed so that it is passive; that is, minimal (human) intervention and risk would be involved in encapsulating LLW species. In addition, the gel materials hold potential significance in environmental remediation of and recovery of metallic cations identified in respective domains and physico-chemical processes. In brief, silica gels start as aqueous/liquid solutions of base catalyzed silica hydrogels and metal ions (targeted species), such as silver. The metal ions are reduced radiolytically and migrate through the solution to form clusters. Upon post-irradiation processing, aerogel monoliths, extremely lightweight but mechanically strong, that encapsulate the metals are produced. Interestingly the radiolytic or photonic source can be gamma-rays and/or other rays from ''artificial sources'', such as reactors, or ''inherent sources'' like those characterizing mixed waste. Polymer gels, in contrast exhibit thermally-induced volumetric contraction at 20-50 C by expelling water from the gels physical state. Further, some functional groups that capture di- or tri-valent cations from aqueous solutions can be incorporated

  17. Radiolytically-induced novel materials and their application to waste processing

    International Nuclear Information System (INIS)

    Massimo Bertino; Akira Tokuhiro; Tadashi Tokuhiro

    2007-01-01

    In the present NEER project we investigated two different types of gel materials with respect to potential applications in environmental remediation, including mixed waste generated from the nuclear fuel cycles. The materials under study were: (1) silica-polymer based aerogel composites into which specific metallic cations diffuse into and remain, and (2) polymer gels made of thermo-sensitive polymer networks, whose functional groups can be ''tailored'' to have a preferred affinity for specific cations, again diffusing into and remaining in the network under a volumetrically, contractive phase-transition. The molecular, diffusion of specific cations, including those of concern in low-level waste streams, into the gel materials studied here indicates that a scaled, engineered system can be designed so that it is passive; that is, minimal (human) intervention and risk would be involved in encapsulating LLW species. In addition, the gel materials hold potential significance in environmental remediation of and recovery of metallic cations identified in respective domains and physico-chemical processes. In brief, silica gels start as aqueous/liquid solutions of base catalyzed silica hydrogels and metal ions (targeted species), such as silver. The metal ions are reduced radiolytically and migrate through the solution to form clusters. Upon post-irradiation processing, aerogel monoliths, extremely lightweight but mechanically strong, that encapsulate the metals are produced. Interestingly the radiolytic or photonic source can be gamma-rays and/or other rays from ''artificial sources'', such as reactors, or ''inherent sources'' like those characterizing mixed waste. Polymer gels, in contrast exhibit thermally-induced volumetric contraction at 20-50 C by expelling water from the gels physical state. Further, some functional groups that capture di- or tri-valent cations from aqueous solutions can be incorporated into the polymer networks on synthesis, including by radiolytic

  18. RADIOLYTIC HYDROGEN GENERATION INSAVANNAH RIVER SITE (SRS) HIGH LEVEL WASTETANKS COMPARISON OF SRS AND HANFORDMODELING PREDICTIONS

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C; Ned Bibler, N

    2009-04-15

    In the high level waste tanks at the Savannah River Site (SRS), hydrogen is produced continuously by interaction of the radiation in the tank with water in the waste. Consequently, the vapor spaces of the tanks are purged to prevent the accumulation of H{sub 2} and possible formation of a flammable mixture in a tank. Personnel at SRS have developed an empirical model to predict the rate of H{sub 2} formation in a tank. The basis of this model is the prediction of the G value for H{sub 2} production. This G value is the number of H{sub 2} molecules produced per 100 eV of radiolytic energy absorbed by the waste. Based on experimental studies it was found that the G value for H{sub 2} production from beta radiation and from gamma radiation were essentially equal. The G value for H{sub 2} production from alpha radiation was somewhat higher. Thus, the model has two equations, one for beta/gamma radiation and one for alpha radiation. Experimental studies have also indicated that both G values are decreased by the presence of nitrate and nitrite ions in the waste. These are the main scavengers for the precursors of H{sub 2} in the waste; thus the equations that were developed predict G values for hydrogen production as a function of the concentrations of these two ions in waste. Knowing the beta/gamma and alpha heat loads in the waste allows one to predict the total generation rate for hydrogen in a tank. With this prediction a ventilation rate can be established for each tank to ensure that a flammable mixture is not formed in the vapor space in a tank. Recently personnel at Hanford have developed a slightly different model for predicting hydrogen G values. Their model includes the same precursor for H{sub 2} as the SRS model but also includes an additional precursor not in the SRS model. Including the second precursor for H{sub 2} leads to different empirical equations for predicting the G values for H{sub 2} as a function of the nitrate and nitrite concentrations in

  19. Opportunities to enhance and interpret nutrient fluxes and imbalances in animal production systems by use of stable isotopes

    International Nuclear Information System (INIS)

    Jarvis, S.C.

    2002-01-01

    key areas in which there is a need for improved understanding. Methods are being developed for understanding and controlling balances and of the processes involved. Increasingly, stable isotopes are being used to help develop this understanding. Examples are given of the way that enriched sources, and particularly natural abundance levels of N are being used to determine the way that controls over the flows of N at various physical scales within particular ecosystems are operating. By way of example, three case studies are taken to illustrate opportunities to employ stable isotopes of N to better understand fluxes, provide improved model description and predictive capability and ultimately to improve the management and outputs from the farm The first is an intensively managed 76 ha temperate dairy system, in SW of England; the second is 2 farming systems in the highlands of E. Kenya where traditional soil fertility practices cannot be maintained with an increasing population and land scarcity, and the final case study is that of a balanced, productive and environmentally sound integrated farming system in which modest amounts of external inputs are used to supplement recycled nutrients within a semi-intensive, agriculture- aquaculture management in Asia. The particular general areas within livestock systems which require further definition to enable improved N utilisation and which can be probed by δ 15 N studies include: impact of dietary quality on N utilisation and partitioning into excreta, the dynamics of N turnover from excreta, plant residues and soil organic matter and effects of changes in local husbandry/management practices, spatial and temporal effects of excretal return (either at grazing or after storage/application), interactions between N, other nutrients and water availability, N sources and rates of transformation and transfers into loss pathways and construction of soil and systems nutrient balances and the identification and determination of

  20. Does the cyclohexyl cation exist in the dilute gas state. Direct evidence from a radiolytic study

    International Nuclear Information System (INIS)

    Attina, M.; Cacace, F.; Giacomello, P.

    1981-01-01

    The isomeric composition of the gaseous C 6 H 11 + cations obtained via hydride ion abstraction from c-C 6 H 12 has been investigated by allowing the charged species to react in the gas phase with water and analyzing the neutral products formed. The nature and the yields of the major products, cyclohexanol, cyclohexanone, and 1-methylcyclopentanol, and their dependence on the pressure and the composition of the gaseous system provide direct evidence for the existence of the cyclohexyl cation in the dilute gas state, with a lifetime in excess of 10 -7 s, and confirm its facile rearrangement to the more stable 1-methylcyclopentyl ion

  1. Nitrate denitrification with nitrite or nitrous oxide as intermediate products: Stoichiometry, kinetics and dynamics of stable isotope signatures.

    Science.gov (United States)

    Vavilin, V A; Rytov, S V

    2015-09-01

    A kinetic analysis of nitrate denitrification by a single or two species of denitrifying bacteria with glucose or ethanol as a carbon source and nitrite or nitrous oxide as intermediate products was performed using experimental data published earlier (Menyailo and Hungate, 2006; Vidal-Gavilan et al., 2013). Modified Monod kinetics was used in the dynamic biological model. The special equations were added to the common dynamic biological model to describe how isotopic fractionation between N species changes. In contrast to the generally assumed first-order kinetics, in this paper, the traditional Rayleigh equation describing stable nitrogen and oxygen isotope fractionation in nitrate was derived from the dynamic isotopic equations for any type of kinetics. In accordance with the model, in Vidal-Gavilan's experiments, the maximum specific rate of nitrate reduction was proved to be less for ethanol compared to glucose. Conversely, the maximum specific rate of nitrite reduction was proved to be much less for glucose compared to ethanol. Thus, the intermediate nitrite concentration was negligible for the ethanol experiment, while it was significant for the glucose experiment. In Menyailo's and Hungate's experiments, the low value of maximum specific rate of nitrous oxide reduction gives high intermediate value of nitrous oxide concentration. The model showed that the dynamics of nitrogen and oxygen isotope signatures are responding to the biological dynamics. Two microbial species instead of single denitrifying bacteria are proved to be more adequate to describe the total process of nitrate denitrification to dinitrogen. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Gamma Radiolytic Degradation of Heptachlor in Methanol and Monitoring of Degradation by HPLC

    International Nuclear Information System (INIS)

    Riaz, M.; Butt, S.B.

    2014-01-01

    Removal of known insecticide Heptachlor (HPTC) in methanol solution by gamma-rays under varied experimental conditions has been optimized. Air saturated solution of HPTC was irradiated at x-rays dose from 1 to 10 kGys. The extent of radiolytic degradation was monitored by reversed phase high performance liquid chromatography (HPLC) coupled with UV detector. At dose of 10 kGys gamma 98 % of HPTC was degraded. The degradation of HPTC occurs by CH/sub 3/O and CH/sub 2/OH radicals generated by methanol radiolysis. It is concluded that gamma-rays can remove Persistent Organic Pollutants (POPs) form environmental matrices. It can decrease the harmful properties of these POPs by their transformation into less resistant fragments to biological / natural elimination in the aquatic atmosphere. (author)

  3. Radiolytic synthesis and electrocatalytic activity of bimetallic nanoaggregates grafted upon various electrodes

    International Nuclear Information System (INIS)

    Amblard, J.; Belloni, J.; Platzer, O.

    1991-01-01

    We show how to utilize the radiolytic pathway for grafting metal nanoaggregates upon anodes or cathodes involved in the chlorine-soda process, thus enhancing their electrochemical behaviour. In both cases important overpotentials are usually measured on unmodified electrodes. The electrocatalytic efficiency of bimetallic nanoparticles (such as Pt-Ru and Ni-Ru), once grafted onto bulk metal electrodes (Ti or Ni), has been investigated by measuring the overpotential for chlorine or hydrogen evolution, respectively. Experimental conditions are similar to those of the industrial process. A synergistic effect is shown when Pt and Ru are alloyed in a 2: 1 atomic ratio. Then the chlorine overpotential is minimum. Conversely, there is no synergy between Ni and Ru, although a minimum amount of Ru in Ru-Ni (50% atomic) ensures a very low hydrogen overpotential [fr

  4. Fast repair of oxidizing OH adducts of DNA by hydroxycinnamic acid derivatives. A pulse radiolytic study

    International Nuclear Information System (INIS)

    Yue Jiang; Lin Weizhen; Yao Side; Lin Nianyun; Zhu Dayuan

    1999-01-01

    Using pulse radiolytic techniques, it has been demonstrated that the interactions of oxidizing OH adducts of DNA (ssDNA and dsDNA), polyA and polyG with hydroxycinnamic acid derivatives proceed via an electron transfer process (k=5-30x10 8 dm 3 mol -1 s -1 ). In addition, the rates for fast repair of OH adducts of dAMP, polyA and DNA (ssDNA and dsDNA) are slower than the corresponding rates for the rest OH adducts of DNA constituents. The slower rates for repair of oxidizing OH adducts of dAMP may be the rate determining step during the interaction of hydroxycinnamic acid derivatives with OH adducts of DNA containing the varieties of OH adducts of DNA constituents

  5. Safety operation of chromatography column system with discharging hydrogen radiolytically generated

    Directory of Open Access Journals (Sweden)

    Watanabe Sou

    2015-01-01

    Full Text Available In the extraction chromatography system, accumulation of hydrogen gas in the chromatography column is suspected to lead to fire or explosion. In order to prevent the hazardous accidents, it is necessary to evaluate behaviors of gas radiolytically generated inside the column. In this study, behaviors of gas inside the extraction chromatography column were investigated through experiments and Computation Fluid Dynamics (CFD simulation. N2 gas once accumulated as bubbles in the packed bed was hardly discharged by the flow of mobile phase. However, the CFD simulation and X-ray imaging on γ-ray irradiated column revealed that during operation the hydrogen gas generated in the column was dissolved into the mobile phase without accumulation and discharged.

  6. Degradation of sulfamethoxazole using ozone and chlorine dioxide - Compound-specific stable isotope analysis, transformation product analysis and mechanistic aspects.

    Science.gov (United States)

    Willach, Sarah; Lutze, Holger V; Eckey, Kevin; Löppenberg, Katja; Lüling, Michelle; Terhalle, Jens; Wolbert, Jens-Benjamin; Jochmann, Maik A; Karst, Uwe; Schmidt, Torsten C

    2017-10-01

    The sulfonamide antibiotic sulfamethoxazole (SMX) is a widely detected micropollutant in surface and groundwaters. Oxidative treatment with e.g. ozone or chlorine dioxide is regularly applied for disinfection purposes at the same time exhibiting a high potential for removal of micropollutants. Especially for nitrogen containing compounds such as SMX, the related reaction mechanisms are largely unknown. In this study, we systematically investigated reaction stoichiometry, product formation and reaction mechanisms in reactions of SMX with ozone and chlorine dioxide. To this end, the neutral and anionic SMX species, which may occur at typical pH-values of water treatment were studied. Two moles of chlorine dioxide and approximately three moles of ozone were consumed per mole SMX degraded. Oxidation of SMX with ozone and chlorine dioxide leads in both cases to six major transformation products (TPs) as revealed by high-resolution mass spectrometry (HRMS). Tentatively formulated TP structures from other studies could partly be confirmed by compound-specific stable isotope analysis (CSIA). However, for one TP, a hydroxylated SMX, it was not possible by HRMS alone to identify whether hydroxylation occurred at the aromatic ring, as suggested in literature before, or at the anilinic nitrogen. By means of CSIA and an analytical standard it was possible to identify sulfamethoxazole hydroxylamine unequivocally as one of the TPs of the reaction of SMX with ozone as well as with chlorine dioxide. H-abstraction and electron transfer at the anilinic nitrogen are suggested as likely initial reactions of ozone and chlorine dioxide, respectively, leading to its formation. Oxidation of anionic SMX with ozone did not show any significant isotopic fractionation whereas the other reactions studied resulted in a significant carbon isotope fractionation. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. Carbon Stable Isotope Values in Plankton and Mussels Reflect Changes in Carbonate Chemistry Associated with Nutrient Enhanced Net Production

    Directory of Open Access Journals (Sweden)

    Autumn Oczkowski

    2018-02-01

    Full Text Available Coastal ecosystems are inherently complex and potentially adaptive as they respond to changes in nutrient loads and climate. We documented the role that carbon stable isotope (δ13C measurements could play in understanding that adaptation with a series of three Ecostat (i.e., continuous culture experiments. We quantified linkages among δ13C, nutrients, carbonate chemistry, primary, and secondary production in temperate estuarine waters. Experimental culture vessels (9.1 L containing 33% whole and 67% filtered (0.2 μm seawater were amended with dissolved inorganic nitrogen (N and phosphorous (P in low (3 vessels; 5 μM N, 0.3 μM P, moderate (3 vessels; 25 μM N, 1.6 μM P, and high amounts (3 vessels; 50 μM N, 3.1 μM P. The parameters necessary to calculate carbonate chemistry, chlorophyll-a concentrations, and particulate δ13C values were measured throughout the 14 day experiments. Outflow lines from the experimental vessels fed 250 ml containers seeded with juvenile blue mussels (Mytilus edulis. Mussel subsamples were harvested on days 0, 7, and 14 and their tissues were analyzed for δ13C values. We consistently observed that particulate δ13C values were positively correlated with chlorophyll-a, carbonate chemistry, and to changes in the ratio of bicarbonate to dissolved carbon dioxide (HCO3-:CO2. While the relative proportion of HCO3- to CO2 increased over the 14 days, concentrations of each declined, reflecting the drawdown of carbon associated with enhanced production. Plankton δ13C values, like chlorophyll-a concentrations, increased over the course of each experiment, with the greatest increases in the moderate and high treatments. Trends in δ13C over time were also observed in the mussel tissues. Despite ecological variability and different plankton abundances the experiments consistently demonstrated how δ13C values in primary producers and consumers reflected nutrient availability, via its impact on carbonate chemistry. We

  8. Evaluate the role of organic acids in the protection of ligands from radiolytic degradation

    Energy Technology Data Exchange (ETDEWEB)

    Miller, Anneka [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mezyk, Stehpen [Idaho National Lab. (INL), Idaho Falls, ID (United States); Peterman, Dean [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-08-01

    In the Advanced TALSPEAK process, the bis(2-ethylhexyl)phosphoric acid (HDEHP) extractant used in the traditional TALSPEAK process is replaced by the extractant 2-ethylhexylphosphonic acid mono-2-ethylhexyl ester (HEH[EHP]). In addition, the aqueous phase complexant and buffer used in traditional TALSPEAK is replaced with the combination of N-(2-hydroxyethyl)ethylenediamine-N,N’,N’-triacetic acid (HEDTA) and citric acid. In order to evaluate the possible impacts of gamma radiolysis upon the efficacy of the Advanced TALSPEAK flowsheet, aqueous and organic phases corresponding to the extraction section of the proposed flowsheet were irradiated in the INL test loop under an ambient atmosphere. The results of these studies conducted at INL, led INL researchers to conclude that the scarcity of values of rate constants for the reaction of hydroxyl radical with the components of the Advanced TALSPEAK process chemistry was severely limiting the interpretation of the results of radiolysis studies performed at the INL. In this work, the rate of reaction of hydroxyl radical with citric acid at several pH values was measured using a competitive pulse radiolysis technique. This report describes those results and is written in completion of milestone M3FT-16IN030102028, the goal of which was to evaluate the role of organic acids in the protection of ligands from radiolytic degradation. The results reported here demonstrate the importance of obtaining hydroxyl radical reaction rate data for the conditions that closely resemble actual solution conditions expected to be used in an actual solvent extraction process. This report describes those results and is written in completion of milestone M3FT-16IN030102028, the goal of which was to evaluate the role of organic acids in the protection of ligands from radiolytic degradation.

  9. Chromatographic studies of gamma radiolysis products of phenols in methanolic solution

    International Nuclear Information System (INIS)

    Cordeiro, P.J.M.

    1989-10-01

    The radiolytic effects on phenolic compounds (catechol, resorcinol, hydroquinone and pyrogallol), under different doses of gamma irradiation, were studied. The results shown that the radiolytic effects are independent of the irradiation doses with almost all compounds formed from the solvent radiolysis. Analysis of the resulting products were carried out by High Performance Liquid Chromatography and Capillary Gas Chromatography. The quantification of these compounds was made by mass spectrometry. (author)

  10. Understanding the sorption behavior of Pu{sup 4+} on poly(amidoamine) dendrimer functionalized carbon nanotube. Sorption equilibrium, mechanism, kinetics, radiolytic stability, and back-extraction studies

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, Parveen [Indian Institute of Technology, Himachal Pradesh (India); Sengupta, Arijit [Bahbha Atomic Research Centre, Mumbai (India). Radiochemistry Div.; Deb, Ashish Kumar Singha; Ali, S. Musharaf [Bahbha Atomic Research Centre, Mumbai (India). Chemical Engineering Div.; Homi Bhabha National Institute, Mumbai (India); Dasgupta, Kinshuk [Bhabha National Institute, Mumbai (India). Mechanical Metallurgy Div.

    2017-07-01

    Poly(amidoamine) dendrimer functionalized carbon nanotube was demonstrated as highly efficient sorbent of the Pu{sup 4+} from radioactive waste solution. The second generation dendrimer was found to have more efficiency as compared to the 1{sup st} generation might be due to the availability of more functionality for coordinating to the Pu{sup 4+} ion. Analysis of different isotherm models revealed that, Langmuir isotherm was predominantly operating through chemi-sorption (with the sorption energy 10.07 and 16.95 kJ mol{sup -1} for 1{sup st} and 2{sup nd} generation dendrimer) with the sorption capacity 89.22 mg g{sup -1} and 92.48 mg g{sup -1} for 1{sup st} and 2{sup nd} generation dendrimer, respectively. Analysis of different sorption kinetics model revealed that the sorption proceeded via pseudo 2{sup nd} order reaction. The 2{sup nd} generation dendrimer was found to be radiolytically more stable while oxalic acid was found to be suitable for quantitative back extraction of Pu{sup 4+}.

  11. Skin autofluorescence is elevated in patients with stable coronary artery disease and is associated with serum levels of neopterin and the soluble receptor for advanced glycation end products

    NARCIS (Netherlands)

    Mulder, Douwe J.; van Haelst, Paul L.; Gross, Sascha; de Leeuw, Karina; Bijzet, Johannes; Graaff, Reindert; Gans, Rijk O.; Zijlstra, Felix; Smit, Andries J.

    Aims: To investigate whether skin autofluorescence (AF), a non-invasive marker for advanced glycation end products (AGEs), is elevated in stable coronary artery disease (sCAD) and to investigate its relationship with serum levels of the soluble receptor for AGEs (sRAGE), neopterin and C-reactive

  12. Compound-specific stable carbon isotopic signature of carbohydrate pyrolysis products from C3 and C4 plants.

    Science.gov (United States)

    González-Pérez, José A; Jiménez-Morillo, Nicasio T; de la Rosa, José M; Almendros, Gonzalo; González-Vila, Francisco J

    2016-02-01

    Pyrolysis-compound specific isotopic analysis (Py-CSIA: Py-GC-(FID)-C-IRMS) is a relatively novel technique that allows on-line quantification of stable isotope proportions in chromatographically separated products released by pyrolysis. Validation of the Py-CSIA technique is compulsory for molecular traceability in basic and applied research. In this work, commercial sucrose from C4 (sugarcane) and C3 (sugarbeet) photosystem plants and admixtures were studied using analytical pyrolysis (Py-GC/MS), bulk δ(13)C IRMS and δ(13)C Py-CSIA. Major pyrolysis compounds were furfural (F), furfural-5-hydroxymethyl (HMF) and levoglucosan (LV). Bulk and main pyrolysis compound δ(13)C (‰) values were dependent on plant origin: C3 (F, -24.65 ± 0.89; HMF, -22.07 ± 0.41‰; LV, -21.74 ± 0.17‰) and C4 (F, -14.35 ± 0.89‰; HMF, -11.22 ± 0.54‰; LV, -11.44 ± 1.26‰). Significant regressions were obtained for δ(13)C of bulk and pyrolysis compounds in C3 and C4 admixtures. Furfural (F) was found (13)C depleted with respect to bulk and HMF and LV, indicating the incorporation of the light carbon atom in position 6 of carbohydrates in the furan ring after pyrolysis. This is the first detailed report on the δ(13)C signature of major pyrolytically generated carbohydrate-derived molecules. The information provided by Py-CSIA is valuable for identifying source marker compounds of use in food science/fraud detection or in environmental research. © 2015 Society of Chemical Industry.

  13. Stable isotopes labelled compounds

    International Nuclear Information System (INIS)

    1982-09-01

    The catalogue on stable isotopes labelled compounds offers deuterium, nitrogen-15, and multiply labelled compounds. It includes: (1) conditions of sale and delivery, (2) the application of stable isotopes, (3) technical information, (4) product specifications, and (5) the complete delivery programme

  14. Stable isotopes

    International Nuclear Information System (INIS)

    Evans, D.K.

    1986-01-01

    Seventy-five percent of the world's stable isotope supply comes from one producer, Oak Ridge Nuclear Laboratory (ORNL) in the US. Canadian concern is that foreign needs will be met only after domestic needs, thus creating a shortage of stable isotopes in Canada. This article describes the present situation in Canada (availability and cost) of stable isotopes, the isotope enrichment techniques, and related research programs at Chalk River Nuclear Laboratories (CRNL)

  15. Modeling of bubble growth in complex fluids. Application to radiolytic swelling of nuclear bituminized waste products

    International Nuclear Information System (INIS)

    Marchal, Antoine

    2015-01-01

    The aim of this PhD thesis is to predict the swelling of bitumen barrels in which radioactive salts are mixed. The bitumen exposed to radioactivity undergoes a chemical reaction: the radiolysis. This implies a generation of dihydrogen. The created is solubilized until the concentration reaches a limit value which is called saturation. Over this limit nucleation of bubbles is observed. Then they will grow thank to the contribution of the gas generated by radiolysis and they will be submitted to Archimede's principle so that they will rise in the fluid. The swelling is the result of the competition between generation and evacuation of gas. A model has been built to describe the evolution of a bubble population. Because of it is not possible to solve it analytically, a numerical program was developed. The results show that an increase of the fluid viscosity, the gas generation or the container height lead to an increase of the swelling and that an increase of the diffusion coefficient contributes to a decrease of the swelling. In the particular case of a yield stress fluid, the behavior of the bubble population is modified and the evacuation of gas is done with several shots, at the opposite of the case of a Newtonian fluid for which a stationary evacuation is reached. (author)

  16. Dosimetry Modeling for Predicting Radiolytic Production at the Spent Fuel - Water Interface

    Energy Technology Data Exchange (ETDEWEB)

    Miller, William H.; Kline, Amanda J.; Hanson, Brady D.

    2006-04-30

    Modeling of the alpha, beta, and gamma dose from spent fuel as a function of particle size and fuel to water ratio was examined. These doses will be combined with modeling of G values and interactions to determine the concentration of various species formed at the fuel water interface and their affect on dissolution rates.

  17. Carbon Stable Isotope Values in Plankton and Mussels Reflect Changes in Carbonate Chemistry Associated with Nutrient Enhanced Net Production

    Science.gov (United States)

    Coastal ecosystems are inherently complex and potentially adaptive as they respond to changes in nutrient loads and climate. We documented the role that carbon stable isotope (δ13C) measurements could play in understanding that adaptation with a series of three Ecostat (i.e...

  18. Ready-to-use parenteral amiodarone : A feasibility study towards a long-term stable product formulation

    NARCIS (Netherlands)

    Jacobs, Maartje S.; Luinstra, Marianne; Moes, Jan Reindert; Chan, Tiffany C. Y.; Minovic, Isidor; Frijlink, Henderik W.; Woerdenbag, Herman J.

    Objectives To determine the feasibility of preparing a long-term stable ready-to-use parenteral amiodarone formulation using cyclodextrins as dissolution enhancer. Methods A preformulation study was performed with different molar ratios of hydroxypropyl-beta-cyclodextrin (HP-BCD) or

  19. The close relation between Lactococcus and Methanosaeta is a keystone for stable methane production from molasses wastewater in a UASB reactor.

    Science.gov (United States)

    Kim, Tae Gwan; Yun, Jeonghee; Cho, Kyung-Suk

    2015-10-01

    The up-flow anaerobic sludge blanket (UASB) reactor is a promising method for the treatment of high-strength industrial wastewaters due to advantage of its high treatment capacity and settleable suspended biomass retention. Molasses wastewater as a sugar-rich waste is one of the most valuable raw material for bioenergy production due to its high organic strength and bioavailability. Interpretation for complex interactions of microbial community structures and operational parameters can help to establish stable biogas production. RNA-based approach for biogas production systems is recommended for analysis of functionally active community members which are significantly underestimated. In this study, methane production and active microbial community were characterized in an UASB reactor using molasses wastewater as feedstock. The UASB reactor achieved a stable process performance at an organic loading rate of 1.7~13.8-g chemical oxygen demand (COD,·L(-1) day(-1); 87-95 % COD removal efficiencies), and the maximum methane production rate was 4.01 L-CH4·at 13.8 g-COD L(-1) day(-1). Lactococcus and Methanosaeta were comprised up to 84 and 80 % of the active bacterial and archaeal communities, respectively. Network analysis of reactor performance and microbial community revealed that Lactococcus and Methanosaeta were network hub nodes and positively correlated each other. In addition, they were positively correlated with methane production and organic loading rate, and they shared the other microbial hub nodes as neighbors. The results indicate that the close association between Lactococcus and Methanosaeta is responsible for the stable production of methane in the UASB reactor using molasses wastewater.

  20. Influence of concentration on the radiolytic decomposition of thiamine, riboflavin, and pyridoxine in aqueous solution

    Directory of Open Access Journals (Sweden)

    Guadalupe Albarrán

    2014-10-01

    Full Text Available Vitamin loss during irradiation has been claimed as a critical area in food irradiation technology, especially that of thiamine (B1, which has been considered as the most sensitive to radiation. Although it has been suggested that no vitamin deficiency could result from consuming irradiated food, a long debate on the loss of vitamins and other nutrients during food irradiation has been maintained by the lack of experimental studies monitoring decomposition rates at different concentrations and doses. Since thiamine, riboflavin, and pyridoxine are labile vitamins, this study has focused on their radiolytic decomposition in dilute aqueous solutions in the presence of air. The decomposition process was followed by HPLC and UV-spectroscopy. The results obtained in aqueous solutions showed a dependence of the decomposition as a nonlinear function of the dose. Of these three compounds, the decomposition was higher for thiamine than for riboflavin and even less in pyridoxine.

  1. Degradation of phenylethylamine and tyramine by gamma radiation process and docking studies of its radiolytes

    Energy Technology Data Exchange (ETDEWEB)

    Cardozo, Monique; Souza, Stefânia Priscila de; Lima, Keila dos Santos Cople; França, Tanos Celmar Costa; Lima, Antonio Luis dos Santos, E-mail: santoslima@ime.eb.br [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Departamanto de Engenharia Quimica; Oliveira, Aline Alves [Universidade de Sao Paulo (USP), São Carlos, SP (Brazil). Instituto de Quimica; Rezende, Cláudia Moraes [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Instituto de Quimica

    2014-07-01

    Biogenic amines (BA) are toxic low molecular weight organic bases with aliphatic or heterocyclic structures that can be found in several foods. The consumption of food containing large amounts of BA can result in allergic reactions, rash, vomiting, and hypertension. Besides, BA are also known as possible precursors of carcinogens. In the present study we evaluated the effect of different gamma irradiation doses on methanol and water solutions of the BA phenylethylamine and tyramine. Our best results showed that, at a dose of 5 kGy (SI unit used for measurement of absorbed dose of ionizing radiation), it was possible to reduce the content of these two BA up to 85 and 60%, respectively, suggesting that the use of the irradiation process can be an efficient tool for its degradation. Further docking studies also suggested that the radiolytes produced in the irradiation process have more affinity for the human detoxifying enzymes monoaminoxidases type A and B (MAO-A and MAO-B) being, therefore, less toxic than its precursors. (author)

  2. Surface capped fluorescent semiconductor nanoparticles: radiolytic synthesis and some of its biological applications

    International Nuclear Information System (INIS)

    Saha, A.

    2006-01-01

    Semiconductor nanocrystals or colloidal quantum dots (QD's) have generated great research interest because of their unusual properties arising out of quantum confinement effects. Many researchers in the field of nanotechnology focus on the 'high quality' semiconductor quantum dots. A good synthetic route should yield nanoparticles with narrow size distribution, good crystallinity, high photostability, desired surface properties and high photoluminescence quantum efficiency. In the domain of colloidal chemistry, reverse micellar synthesis, high temperature thermolysis using organometallic precursors and synthesis in aqueous media using polyphosphates or thiols as stabilizers are the most prominent ones. In contrast, γ-radiation assisted synthesis can offer a simplified approach to prepare size-controlled nanoparticles at room temperature. Syntheses of thiol-capped II-VI nanoparticles by radiolytic method, its characterization and some of its luminescence-based applications of biological relevance will be presented. The versatility of thiols (RSH) can be emphasized here as changing the R-group imparts different functionality to the particles and thus chemical behavior of the particles can be manipulated according to the application intended for. (authors)

  3. Size-Controlled and Optical Properties of Monodispersed Silver Nanoparticles Synthesized by the Radiolytic Reduction Method

    Science.gov (United States)

    Saion, Elias; Gharibshahi, Elham; Naghavi, Kazem

    2013-01-01

    Size-controlled and monodispersed silver nanoparticles were synthesized from an aqueous solution containing silver nitrate as a metal precursor, polyvinyl alcohol as a capping agent, isopropyl alcohol as hydrogen and hydroxyl radical scavengers, and deionized water as a solvent with a simple radiolytic method. The average particle size decreased with an increase in dose due to the domination of nucleation over ion association in the formation of the nanoparticles by gamma reduction. The silver nanoparticles exhibit a very sharp and strong absorption spectrum with the absorption maximum λmax blue shifting with an increased dose, owing to a decrease in particle size. The absorption spectra of silver nanoparticles of various particle sizes were also calculated using a quantum physics treatment and an agreement was obtained with the experimental absorption data. The results suggest that the absorption spectrum of silver nanoparticles possibly derived from the intra-band excitations of conduction electrons from the lowest energy state (n = 5, l = 0) to higher energy states (n ≥ 6; Δl = 0, ±1; Δs = 0, ±1), allowed by the quantum numbers principle. This demonstrates that the absorption phenomenon of metal nanoparticles based on a quantum physics description could be exploited to be added into the fundamentals of metal nanoparticles and the related fields of nanoscience and nanotechnology. PMID:23579953

  4. Structural, Optical and Electrical Properties of PVA/PANI/Nickel Nanocomposites Synthesized by Gamma Radiolytic Method

    Directory of Open Access Journals (Sweden)

    Abdo Mohd Meftah

    2014-09-01

    Full Text Available This article reports a simultaneous synthesis of polyaniline (PANI and nickel (Ni nanoparticles embedded in polyvinyl alcohol (PVA film matrix by gamma radiolytic method. The mechanism of formation of PANI and Ni nanoparticles were proposed via oxidation of aniline and reduction of Ni ions, respectively. The effects of dose and Ni ions concentration on structural, optical, and electrical properties of the final PVA/PANI/Ni nanocomposites film were carefully examined. The structural and morphological studies show the presence of PANI with irregular granular microstructure and Ni nanoparticles with spherical shape and diameter less than 60 nm. The average particle size of Ni nanoparticles decreased with increasing dose and decreasing of precursor concentration due to increase of nucleation process over aggregation process during gamma irradiation. The optical absorption spectra showed that the absorption peak of Ni nanoparticles at about 390 nm shifted to lower wavelength and the absorbance increased with increasing dose. The formation of PANI was also revealed at 730 nm absorption peak with the absorbance increasing by the increase of dose. The electrical conductivity increased with increasing of dose and chlorine concentration due to number of polarons formation increases in the PVA/PANI/Ni nanocomposites.

  5. A systematic study on the alteration in physiochemical and metal retention properties of radiolytically degraded TBP-DD-HNO3 and TBP-NPH-HNO3 systems

    International Nuclear Information System (INIS)

    Mishra, Satyabrata; Mallika, C.; Kamachi Mudali, U.; Natarajan, R.

    2014-01-01

    PUREX (Plutonium Uranium EXtraction) process using 30% TBP in NPH (n-paraffin hydrocarbon) or DD (dodecane) as the solvent is widely adopted for the selective extraction of Pu and U from a feed containing highly radioactive fission and activation products in about 3-4 M HNO 3 solution in the reprocessing of spent fuels of Fast Breeder Reactors. During extraction the solvent comes in contact with acid and intense radiation. Nitric acid also gets extracted into the solvent. The acid induced radiolytic transformations in the solvent result in the formation of a number of hydrophobic compounds that are normally not removed efficiently from the solvent by alkaline wash before recycling. As a consequence, the extraction and stripping behaviour of actinides as well as hydrodynamic properties such as density, viscosity, and phase disengagement time (PDT) are greatly altered. Published data on the radiation-chemical degradation of the solvent in different diluents are contradictory, as the irradiation procedures are not identical. For instance, Tripathi and Ramanujam have reported values of 0.837 and 0.841 g/cc for the density and 1.96 and 2.16 mPa.s for the viscosity of 30 % TBP-DD + 3 M HNO 3 before and after exposure to 12 MRad respectively. The density and viscosity measured by Venkatesan et al. for 30 % TBP-NPH and 30 % TBP-NPH + 4 M HNO 3 after irradiating to 10 MRad were 0.812 and 0.842 g/cc and 1.844 and 1.945 mPa.s respectively. Hence, a systematic study has been undertaken to compare the physiochemical transformations in 30 TBP-DD/NPH-HNO 3 system during accelerated radiolysis as a function of radiation dose. Radiolytic degradation of different sets of solutions comprising 30 % TBP-DD (I), 30 % TBP-DD + 4 M HNO 3 (v/v) (II), 30 % TBP-NPH (III) and 30 % TBP-NPH + 4 M HNO 3 (v/v) (IV) was carried out using 60 Co gamma source up to 20 MRad absorbed dose. Physiochemical properties and metal retention behaviour of the samples were measured after regular intervals of 5

  6. Large angle production of stable particles heavier than the proton and a search for quarks at the CERN intersecting storage rings

    CERN Document Server

    Alper, B; Booth, P; Bulos, F; Carroll, L J; Damgaard, G; Duff, Brian G; Heymann, Franz F; Jackson, J N; Jarlskog, G; Jönsson, L B; Klovning, A; Leistam, L; Lillethun, E; Lynch, G; Manning, Geoffrey; Prentice, M; Quarrie, D; von Dardel, Guy F; Weiss, J M

    1973-01-01

    Measurements have been performed on production of particles with mass >1.5 GeV/c/sup 2/ and charge >or=2/3 for theta /sub lab/=62.5 degrees and square root s=53 GeV. At p/sub T/=0.7 GeV/c the relative rate of production of antideuterons to pi /sup -/ is (5+or-1)*10/sup -5/. The deuteron to antideuteron ratio is 3.7+or-1.2. No new stable particle has been seen amongst 0.7*10/sup 8/ charged particles entering our detector. (7 refs).

  7. Stable acetate production in extreme-thermophilic (70ºC) mixed culture fermentation by selective enrichment of hydrogenotrophic methanogens

    NARCIS (Netherlands)

    Zhang, F.; Zhang, Y.; Ding, J.; Dai, K.; Van Loosdrecht, M.C.M.; Zeng, R.J.

    2014-01-01

    The control of metabolite production is difficult in mixed culture fermentation. This is particularly related to hydrogen inhibition. In this work, hydrogenotrophic methanogens were selectively enriched to reduce the hydrogen partial pressure and to realize efficient acetate production in

  8. Leaf and root pectin methylesterase activity and 13C/12C stable isotopic ratio measurements of methanol emissions give insight into methanol production in Lycopersicon esculentum.

    Science.gov (United States)

    Oikawa, Patricia Yoshino; Giebel, Brian M; Sternberg, Leonel da Silveira Lobo O'Reilly; Li, Lei; Timko, Michael P; Swart, Peter K; Riemer, Daniel D; Mak, John E; Lerdau, Manuel T

    2011-09-01

    Plant production of methanol (MeOH) is a poorly understood aspect of metabolism, and understanding MeOH production in plants is crucial for modeling MeOH emissions. Here, we have examined the source of MeOH emissions from mature and immature leaves and whether pectin methylesterase (PME) activity is a good predictor of MeOH emission. We also investigated the significance of below-ground MeOH production for mature leaf emissions. We present measurements of MeOH emission, PME activity, and MeOH concentration in mature and immature tissues of tomato (Lycopersicon esculentum). We also present stable carbon isotopic signatures of MeOH emission and the pectin methoxyl pool. Our results suggest that below-ground MeOH production was not the dominant contributor to daytime MeOH emissions from mature and immature leaves. Stable carbon isotopic signatures of mature and immature leaf MeOH were similar, suggesting that they were derived from the same pathway. Foliar PME activity was related to MeOH flux, but unexplained variance suggested PME activity could not predict emissions. The data show that MeOH production and emission are complex and cannot be predicted using PME activity alone. We hypothesize that substrate limitation of MeOH synthesis and MeOH catabolism may be important regulators of MeOH emission. © 2011 The Authors. New Phytologist © 2011 New Phytologist Trust.

  9. Radiolytic syntheses of hollow UO2 nanospheres in Triton X-100-based lyotropic liquid crystals

    International Nuclear Information System (INIS)

    Wang, Yongming; Chen, Qingde; Shen, Xinghai

    2017-01-01

    Hollow nanospheres (φ: 60-80 nm, wall thickness: 10-20 nm), consisted of UO 2 nanoparticles (φ: 3-5 nm), were successfully prepared in a Triton X-100-water (50:50, w/w) hexagonal lyotropic liquid crystal (LLC) by γ-irradiation, where water soluble ammonium uranyl tricarbonate was added as precursor. The product was stable at least up to 300 C. Furthermore, whether the nanospheres were hollow or not, and the wall thickness of the hollow nanospheres could be easily controlled via adjusting dose rate. While in the Triton X-100 based micellar systems, only solid nanospheres were obtained. At last, a possible combination mechanism containing adsorption, aggregation and fracturing processes was proposed.

  10. Stable and Efficient CuO Based Photocathode through Oxygen-Rich Composition and Au-Pd Nanostructure Incorporation for Solar-Hydrogen Production.

    Science.gov (United States)

    Masudy-Panah, Saeid; Siavash Moakhar, Roozbeh; Chua, Chin Sheng; Kushwaha, Ajay; Dalapati, Goutam Kumar

    2017-08-23

    Enhancing stability against photocorrosion and improving photocurrent response are the main challenges toward the development of cupric oxide (CuO) based photocathodes for solar-driven hydrogen production. In this paper, stable and efficient CuO-photocathodes have been developed using in situ materials engineering and through gold-palladium (Au-Pd) nanoparticles deposition on the CuO surface. The CuO photocathode exhibits a photocurrent generation of ∼3 mA/cm 2 at 0 V v/s RHE. Time-of-flight secondary ion mass spectrometry (TOF-SIMS) analysis and X-ray spectroscopy (XPS) confirm the formation of oxygen-rich (O-rich) CuO film which demonstrates a highly stable photocathode with retained photocurrent of ∼90% for 20 min. The influence of chemical composition on the photocathode performance and stability has been discussed in detail. In addition, O-rich CuO photocathodes deposited with Au-Pd nanostructures have shown enhanced photoelectrochemical performance. Linear scan voltammetry characteristic shows ∼25% enhancement in photocurrent after Au-Pd deposition and reaches ∼4 mA/cm 2 at "0" V v/s RHE. Hydrogen evolution rate significantly depends on the elemental composition of CuO and metal nanostructure. The present work has demonstrated a stable photocathode with high photocurrent for visible-light-driven water splitting and hydrogen production.

  11. High-yield production of a stable Vero cell-based vaccine candidate against the highly pathogenic avian influenza virus H5N1

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Fangye; Zhou, Jian; Ma, Lei; Song, Shaohui; Zhang, Xinwen; Li, Weidong; Jiang, Shude [No. 5, Department of Bioproducts, Institute of Medical Biology, Chinese Academy of Medical Science and Pecking Union Medical College, Jiaoling Avenue 935, Kunming, Yunnan Province 650102, People' s Republic of China (China); Wang, Yue, E-mail: euy-tokyo@umin.ac.jp [National Institute for Viral Disease Control and Prevention, China Center for Disease Control and Prevention, Yingxin Lane 100, Xicheng District, Beijing 100052, People' s Republic of China (China); Liao, Guoyang, E-mail: liaogy@21cn.com [No. 5, Department of Bioproducts, Institute of Medical Biology, Chinese Academy of Medical Science and Pecking Union Medical College, Jiaoling Avenue 935, Kunming, Yunnan Province 650102, People' s Republic of China (China)

    2012-05-18

    Highlights: Black-Right-Pointing-Pointer Vero cell-based HPAI H5N1 vaccine with stable high yield. Black-Right-Pointing-Pointer Stable high yield derived from the YNVa H3N2 backbone. Black-Right-Pointing-Pointer H5N1/YNVa has a similar safety and immunogenicity to H5N1delta. -- Abstract: Highly pathogenic avian influenza (HPAI) viruses pose a global pandemic threat, for which rapid large-scale vaccine production technology is critical for prevention and control. Because chickens are highly susceptible to HPAI viruses, the supply of chicken embryos for vaccine production might be depleted during a virus outbreak. Therefore, developing HPAI virus vaccines using other technologies is critical. Meeting vaccine demand using the Vero cell-based fermentation process has been hindered by low stability and yield. In this study, a Vero cell-based HPAI H5N1 vaccine candidate (H5N1/YNVa) with stable high yield was achieved by reassortment of the Vero-adapted (Va) high growth A/Yunnan/1/2005(H3N2) (YNVa) virus with the A/Anhui/1/2005(H5N1) attenuated influenza vaccine strain (H5N1delta) using the 6/2 method. The reassorted H5N1/YNVa vaccine maintained a high hemagglutination (HA) titer of 1024. Furthermore, H5N1/YNVa displayed low pathogenicity and uniform immunogenicity compared to that of the parent virus.

  12. High-yield production of a stable Vero cell-based vaccine candidate against the highly pathogenic avian influenza virus H5N1

    International Nuclear Information System (INIS)

    Zhou, Fangye; Zhou, Jian; Ma, Lei; Song, Shaohui; Zhang, Xinwen; Li, Weidong; Jiang, Shude; Wang, Yue; Liao, Guoyang

    2012-01-01

    Highlights: ► Vero cell-based HPAI H5N1 vaccine with stable high yield. ► Stable high yield derived from the YNVa H3N2 backbone. ► H5N1/YNVa has a similar safety and immunogenicity to H5N1delta. -- Abstract: Highly pathogenic avian influenza (HPAI) viruses pose a global pandemic threat, for which rapid large-scale vaccine production technology is critical for prevention and control. Because chickens are highly susceptible to HPAI viruses, the supply of chicken embryos for vaccine production might be depleted during a virus outbreak. Therefore, developing HPAI virus vaccines using other technologies is critical. Meeting vaccine demand using the Vero cell-based fermentation process has been hindered by low stability and yield. In this study, a Vero cell-based HPAI H5N1 vaccine candidate (H5N1/YNVa) with stable high yield was achieved by reassortment of the Vero-adapted (Va) high growth A/Yunnan/1/2005(H3N2) (YNVa) virus with the A/Anhui/1/2005(H5N1) attenuated influenza vaccine strain (H5N1delta) using the 6/2 method. The reassorted H5N1/YNVa vaccine maintained a high hemagglutination (HA) titer of 1024. Furthermore, H5N1/YNVa displayed low pathogenicity and uniform immunogenicity compared to that of the parent virus.

  13. Elucidation of oxidation and degradation products of oxygen containing fuel components by combined use of a stable isotopic tracer and mass spectrometry.

    Science.gov (United States)

    Frauscher, Marcella; Besser, Charlotte; Allmaier, Günter; Dörr, Nicole

    2017-11-15

    In order to reveal the degradation products of oxygen-containing fuel components, in particular fatty acid methyl esters, a novel approach was developed to characterize the oxidation behaviour. Combination of artificial alteration under pressurized oxygen atmosphere, a stable isotopic tracer, and gas chromatography electron impact mass spectrometry (GC-EI-MS) was used to obtain detailed information on the formation of oxidation products of (9Z), (12Z)-octadecadienoic acid methyl ester (C18:2 ME). Thereby, biodiesel simulating model compound C18:2 ME was oxidized in a rotating pressurized vessel standardized for lubricant oxidation tests (RPVOT), i.e., artificially altered, under 16 O 2 as well as 18 O 2 atmosphere. Identification of the formed degradation products, mainly carboxylic acids of various chain lengths, alcohols, ketones, and esters, was performed by means of GC-EI-MS. Comparison of mass spectra of compounds under both atmospheres revealed not only the degree of oxidation and the origin of oxygen atoms, but also the sites of oxidative attack and bond cleavage. Hence, the developed and outlined strategy based on a gas-phase stable isotopic tracer and mass spectrometry provides insight into the degradation of oxygen-containing fuels and fuel components by means of the accurate differentiation of oxygen origin in a degradation product. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Hyper production of alkali stable xylanase in lesser duration by Bacillus pumilus SV-85S using wheat bran under solid state fermentation.

    Science.gov (United States)

    Nagar, Sushil; Mittal, Anuradha; Kumar, Davender; Kumar, Lalit; Kuhad, Ramesh Chander; Gupta, Vijay Kumar

    2011-10-01

    High level production of an extracellular cellulase-poor alkali stable xylanase has been conceded from newly isolated Bacillus pumilus SV-85S under solid state fermentation using wheat bran as a substrate. Optimization of the fermentation conditions enhanced the enzyme production to 73,000 ± 1,000 IU/g dry substrate, which was 13.8-fold higher than unoptimized conditions (5,300 IU/g). The enzyme titre was highest after 48 h of incubation at 30°C with 1:3 ratios of substrate to moistening agent using wheat bran as a carbon source. The enzyme could be produced in significant levels by using either tap water or distilled water alone as a moistening agent. An elevated production of xylanase by B. pumilus SV-85S in the presence of wheat bran, a cheap and easily available agro-residue, in shorter duration would apparently reduce the enzyme cost substantially. The enzyme was completely stable over a broad pH (5-11) range and retained 52% of its activity at a temperature of 70°C for 30 min. The desired characteristics of this enzyme together with economic production would be important for its application in paper and pulp industry. Copyright © 2011 Elsevier B.V. All rights reserved.

  15. Mixing of radiolytic hydrogen generated within a containment compartment following a LOCA

    International Nuclear Information System (INIS)

    Willcutt, G.J.E. Jr.; Gido, R.G.

    1978-07-01

    The objective of this work was to determine hydrogen concentration variations with position and time in a closed containment compartment with radiolytic hydrogen generation in the water on the compartment floor following a Loss-of-Coolant-Accident (LOCA). One application is to determine the potential difference between the compartment maximum hydrogen concentration and a hydrogen detector reading, due to the detector location. Three possible mechanisms for hydrogen transport in the compartment were investigated: (1) molecular diffusion, (2) possible bubble formation and motion, and (3) natural convection flows. A base case cubic compartment with 6.55-m (21.5-ft) height was analyzed. Parameter studies were used to determine the sensitivity of results to compartment size, hydrogen generation rates, diffusion coefficients, and the temperature difference between the floor and the ceiling and walls of the compartment. Diffusion modeling indicates that if no other mixing mechanism is present for the base case, the maximum hydrogen volume percent (vol percent) concentration difference between the compartment floor and ceiling will be 4.8 percent. It will be 24.5 days before the maximum concentration difference is less than 0.5 percent. Bubbles do not appear to be a potential source of hydrogen pocketing in a containment compartment. Compartment natural convection circulation rates for a 2.8 K (5 0 F) temperature difference between the floor and the ceiling and walls are estimated to be at least the equivalent of 1 compartment volume per hour and probably in the range of 4 to 9 compartment volumes per hour. Related natural convection studies indicate there will be turbulent mixing in the compartment for a 2.8 K (5 0 F) temperature difference between the floor and the ceiling and walls

  16. Measurements of the radiolytic oxidation of aqueous CsI using a sparging apparatus

    International Nuclear Information System (INIS)

    Ashmore, C.B.; Brown, D.; Sims, H.E.; Gwyther, J.R.

    1996-01-01

    Radiolytic oxidation is considered to be the main mechanism for the formation of I 2 from aqueous CsI in containment of a water cooled reactor after a LOCA. Despite the amount of study over the last 60 years on the radiation chemistry of iodine there has been no consistent set of experiments spanning a wide enough range of conditions to verify models with confidence. This paper describes results from a set of experiments carried out in order to remedy this deficiency. In this work the rate of evolution of I 2 from sparged irradiated CsI solution labeled with 131 I was measured on-line over a range of conditions. This work involved the measurement of the effects of pH, temperature, O 2 concentration, I - concentration, phosphate concentration, dose-rate and impurities on the rate of evolution of I 2 . The range of conditions was chosen in order to span as closely as possible conditions expected in a LOCA but also to help to elucidate some of the mechanisms especially at high pH. pH was found to be a very important factor influencing iodine volatility, over the temperature range studied the extent of oxidation reduced with temperature but this was compensated for by the decrease in partition coefficient. Oxygen concentration was more important in solutions not containing phosphate. The fractional oxidation was not particularly dependent on iodide concentration but G I2 was very dependent on [I - ]. There was no effect of added impurities, Fe, Mn, Mo or organics although in separate work silver was found to have a very important effect. During attempts to interpret the data it was found that it was necessary to include the iodine atom as a volatile species with a partition coefficient of 1.9 taken from thermodynamic data. The modelling work is described in a separate paper. (author) 15 figs., 1 tab., 19 refs

  17. Radiolytic stabilization of poly(methyl methacrylate) in blends with polystyrene

    International Nuclear Information System (INIS)

    Lima, Ivania Soares de

    2002-04-01

    In this work the radiolytic stabilization of poly(methyl methacrylate) was analyzed by three radioprotective agents: polystyrene (PS) and hindered amine light stabilizers (HEALS), respectively, PMMA/PS systems, so a called polymeric blends were prepared with different compositions, where the miscibility of these blends were studied using viscometric, microscopy (SEM) and spectroscopy (FT-IR) techniques. The results show that PMMA/PS blends in the compositions below 10 wt% of PS are miscible, on films casting from solution of toluene and methyl-ethyl-ketone (1;1) mixture. On the other hand, in the composition above 10 wt% of PS, PMMA/PS blends show imminiscibility behavior. These polymer solutions were irradiated with gamma rays ( 60 Co) and viscometric, microscopic and spectroscopic experiments show gamma radiation-induced compatibilization on PMMA/PS blends on proportion 50/50 and 30/70 take place. Viscometric interaction parameters of miscible and compatibilized PMMA/PS bends were calculated in the range of - 50 kGy, with the goal to find out the polymeric interactions after irradiation of the films. G values of PMMA, PMMA/PS and PMMA+St systems were calculated in order to analyze the radioprotection of PS and St into PMMA matrix. The results show that (90/10) PMMA/PS and PMMA+1,5%St systems promote protection against the gamma the radiation-induced scissions, effect that leads to polymer degradation. Moreover, a small amount of crosslinking observed in irradiated blends has contributed to stabilize mechanical properties of PMMA films. PMMA+0,3% HALS system irradiated in doses above 60 kGy showed little stabilization of the mechanical properties of PMMA, since it was observed mechanical degradation this system. Based on these results, PS and St showed to be the best radioprotective agents to PMMA. (author)

  18. Highly stable ceria-zirconia-yttria supported Ni catalysts for syngas production by CO2 reforming of methane

    Science.gov (United States)

    Muñoz, M. A.; Calvino, J. J.; Rodríguez-Izquierdo, J. M.; Blanco, G.; Arias, D. C.; Pérez-Omil, J. A.; Hernández-Garrido, J. C.; González-Leal, J. M.; Cauqui, M. A.; Yeste, M. P.

    2017-12-01

    Ni/CeO2/YSZ and Ni/Ce0.15Zr0.85O2 have been investigated as catalysts for the dry reforming of methane at 750 °C. Ni was incorporated by the impregnation method. The supports were previously activated by using a thermo-chemical protocol consisting on a severe reduction (H2/Ar) at 950 °C followed by a mild oxidation (O2/He) at 500 °C. According to TPR results, this protocol leads to the development of unique redox properties in the case of the CeO2/YSZ oxide. Two types of CO2 + CH4 (1:1) mixtures (helium-diluted and undiluted) were used to feed the reactor. When using the Ni/Ce0.15Zr0.85O2 catalyst with undiluted feed, the reactor became plugged by coke. By contrast, Ni/CeO2/YSZ behaved as an active and stable catalyst even under the most severe operation conditions. The characterization of the spent Ni/CeO2/YSZ using TGA, TEM, Raman and XPS spectroscopy revealed that only a limited amount of graphitic carbon, in form of nanotubes, was formed. No evidences of deactivating carbonaceous forms were obtained. The singular redox properties of the activated CeO2/YSZ oxides are proposed as a key for designing Ni catalysts highly stable in reforming processes.

  19. Production of stable superhydrophilic surfaces on 316L steel by simultaneous laser texturing and SiO2 deposition

    Science.gov (United States)

    Rajab, Fatema H.; Liu, Zhu; Li, Lin

    2018-01-01

    Superhydrophilic surfaces with liquid contact angles of less than 5 ° have attracted much interest in practical applications including self-cleaning, cell manipulation, adhesion enhancement, anti-fogging, fluid flow control and evaporative cooling. Standard laser metal texturing method often result in unstable wetting characteristics, i.e. changing from super hydrophilic to hydrophobic in a few days or weeks. In this paper, a simple one step method is reported for fabricating a stable superhydrophilic metallic surface that lasted for at least 6 months. Here, 316L stainless steel substrates were textured using a nanosecond laser with in-situ SiO2 deposition. Morphology and chemistry of laser-textured surfaces were characterised using SEM, XRD, XPS and an optical 3D profiler. Static wettability analysis was carried out over a period of 6 months after the laser treatment. The effect of surface roughness on wettability was also studied. Results showed that the wettability of the textured surfaces could be controlled by changing the scanning speed of laser beam and number of passes. The main reason for the realisation of the stable superhydrophilic surface is the combination of the melted glass particles mainly Si and O with that of stainless steel in the micro-textured patterns. This study presents a useful method

  20. Identification of some OH radical-induced products of lysozyme

    International Nuclear Information System (INIS)

    Dizdaroglu, M.; Gajewski, E.; Simic, M.G.

    1983-01-01

    OH radical reactions with lysozyme in #betta#-irradiated N 2 O saturated aqueous solutions caused formation of allo-threonine, α-amino-n-butyric acid, o- and m-tyrosines, and 2- and 3-hydroxytyrosines. These identified radiolytic products were characterized by capillary gas chromatography-mass spectrometry as their trimethylsilyl derivatives after HCl-hydrolysis of irradiated lysozyme. Their initial G-values were also determined using gas chromatography. The possible use of these radiolytic products as monitors of radiation-induced damage to proteins and the sites of attack are also discussed. (author)

  1. Wheat bran as a substrate for thermo stable alpha-amylase production by gamma irradiated bacillus megaterium in solid state fermentation

    International Nuclear Information System (INIS)

    ElVatal, A.I.; Khalaf, M.A.

    2003-01-01

    Thermo stable alpha-amylase (EC 3.2.1.1) production from cheap agriculture-industrial waste wheat bran (WB) medium by superior potent gamma irradiated locally isolated strain of Bacillus megaterium in solid state fermentation (SSF) was studied. A highly yielding, stable enhanced isolated strain of bacillus megaterium in solid state fermentation (SSF) was studied. A highly yielding stable enhanced isolate B. megaterium- gamma 21F derived from the 10 kGy, treatment, exhibited the highest alpha-amylase activity under SSF, with 2.8 fold more enzyme titer as compared to the unirradiated wild strain. A vancomycin (Vm) resistant gamma irradiated enhanced isolate B. megaterium-gamma 21F2 (which was selected throughout the subsequent work) secreted (1.27 and 3.58) folds superior titers of alpha-amylase than the gamma irradiated parent isolate (B.megaterium -gamma21F) and unirradiated wild strain, respectively under SSF process. The effects of various parameters, such as moistening agent, initial moisture content level, initial ph, incubation temperature, inoculum size and incubation time on thermo stable alpha-amylase production by B.megaterium-gamma 21F2 under SSF were studied. Maximum enzyme production was recorded in WB medium moistened with (1:2, w/v) distilled water at initial ph (7.0) and inoculated with (2.24 x 10 8 cells/g WB) after 48 h incubation at 40 C degree. Between different solvents used for enzyme extraction from fermented WB mass, distilled water at ph (7.0) was the superior efficient leaching solvent. The specific activity of the precipitated partially purified crude thermo stable enzyme was (258.7 U/mg protein) with ph optima (6.5-7.0), at optimal temperatures (65-70 c degree) and it retained about 53% of its maximum activity after 12 h incubation at 70 c degree. The partially purified crude enzyme was used for starch digestion (5%0 under optimized reaction conditions, wherein (98.2%) starch hydrolysis was attained after 6 h

  2. One-pot bioprocess for lactic acid production from lignocellulosic agro-wastes by using ionic liquid stable Lactobacillus brevis.

    Science.gov (United States)

    Grewal, Jasneet; Khare, S K

    2018-03-01

    The lignocellulosic agro-wastes are an attractive renewable resource in biorefinery for production of value-added platform chemicals and biofuels. The study describes use of different agro-wastes as substrate for production of lactic acid, a C3-platform chemical and high demand industrial product by Lactobacillus brevis in a one-pot bioprocess. The simultaneous saccharification and co-fermentation (SSCF) process was achieved by L. brevis governed fermentation of sugars, derived from saccharification of ionic liquid pretreated feedstocks by nanoimmobilized cellulase, which was further recovered and used for consecutive cycle. The lactic acid yields of 0.22, 0.49, 0.52 g/g were obtained from cottonseed cake, wheat straw and sugarcane bagasse, respectively. The ionic liquid-tolerant L. brevis, cellulolytic reusable nanoimmobilized enzyme coupled with valorization of renewable feedstocks points towards a holistic approach for future biorefineries with sustainable production of bioproducts. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. A Stable, Magnetic, and Metallic Li3O4 Compound as a Discharge Product in a Li-Air Battery.

    Science.gov (United States)

    Yang, Guochun; Wang, Yanchao; Ma, Yanming

    2014-08-07

    The Li-air battery with the specific energy exceeding that of a Li ion battery has been aimed as the next-generation battery. The improvement of the performance of the Li-air battery needs a full resolution of the actual discharge products. Li2O2 has been long recognized as the main discharge product, with which, however, there are obvious failures on the understanding of various experimental observations (e.g., magnetism, oxygen K-edge spectrum, etc.) on discharge products. There is a possibility of the existence of other Li-O compounds unknown thus far. Here, a hitherto unknown Li3O4 compound as a discharge product of the Li-air battery was predicted through first-principles swarm structure searching calculations. The new compound has a unique structure featuring the mixture of superoxide O2(-) and peroxide O2(2-), the first such example in the Li-O system. The existence of superoxide O2(-) creates magnetism and hole-doped metallicity. Findings of Li3O4 gave rise to direct explanations of the unresolved experimental magnetism, triple peaks of oxygen K-edge spectra, and the Raman peak at 1125 cm(-1) of the discharge products. Our work enables an opportunity for the performance of capacity, charge overpotential, and round-trip efficiency of the Li-air battery.

  4. Different Assay Conditions for Detecting the Production and Release of Heat-Labile and Heat-Stable Toxins in Enterotoxigenic Escherichia coli Isolates

    Directory of Open Access Journals (Sweden)

    Letícia B. Rocha

    2013-12-01

    Full Text Available Enterotoxigenic Escherichia coli (ETEC produce heat-labile (LT and/or heat-stable enterotoxins (ST. Despite that, the mechanism of action of both toxins are well known, there is great controversy in the literature concerning the in vitro production and release of LT and, for ST, no major concerns have been discussed. Furthermore, the majority of published papers describe the use of only one or a few ETEC isolates to define the production and release of these toxins, which hinders the detection of ETEC by phenotypic approaches. Thus, the present study was undertaken to obtain a better understanding of ST and LT toxin production and release under laboratory conditions. Accordingly, a collection of 90 LT-, ST-, and ST/LT-producing ETEC isolates was used to determine a protocol for toxin production and release aimed at ETEC detection. For this, we used previously raised anti-LT antibodies and the anti-ST monoclonal and polyclonal antibodies described herein. The presence of bile salts and the use of certain antibiotics improved ETEC toxin production/release. Triton X-100, as chemical treatment, proved to be an alternative method for toxin release. Consequently, a common protocol that can increase the production and release of LT and ST toxins could facilitate and enhance the sensitivity of diagnostic tests for ETEC using the raised and described antibodies in the present work.

  5. High yield production of influenza virus in Madin Darby canine kidney (MDCK cells with stable knockdown of IRF7.

    Directory of Open Access Journals (Sweden)

    Itsuki Hamamoto

    Full Text Available Influenza is a serious public health problem that causes a contagious respiratory disease. Vaccination is the most effective strategy to reduce transmission and prevent influenza. In recent years, cell-based vaccines have been developed with continuous cell lines such as Madin-Darby canine kidney (MDCK and Vero. However, wild-type influenza and egg-based vaccine seed viruses will not grow efficiently in these cell lines. Therefore, improvement of virus growth is strongly required for development of vaccine seed viruses and cell-based influenza vaccine production. The aim of our research is to develop novel MDCK cells supporting highly efficient propagation of influenza virus in order to expand the capacity of vaccine production. In this study, we screened a human siRNA library that involves 78 target molecules relating to three major type I interferon (IFN pathways to identify genes that when knocked down by siRNA lead to enhanced production of influenza virus A/Puerto Rico/8/1934 in A549 cells. The siRNAs targeting 23 candidate genes were selected to undergo a second screening pass in MDCK cells. We examined the effects of knockdown of target genes on the viral production using newly designed siRNAs based on sequence analyses. Knockdown of the expression of a canine gene corresponding to human IRF7 by siRNA increased the efficiency of viral production in MDCK cells through an unknown process that includes the mechanisms other than inhibition of IFN-α/β induction. Furthermore, the viral yield greatly increased in MDCK cells stably transduced with the lentiviral vector for expression of short hairpin RNA against IRF7 compared with that in control MDCK cells. Therefore, we propose that modified MDCK cells with lower expression level of IRF7 could be useful not only for increasing the capacity of vaccine production but also facilitating the process of seed virus isolation from clinical specimens for manufacturing of vaccines.

  6. Seasonal and spatial trends in production and stable isotope signatures of primary producers in Alberta oil sands reclamation wetlands

    International Nuclear Information System (INIS)

    Boutsivongsakd, M; Chen, H.; Legg, A.; Farwell, A.; Dixon, G.

    2010-01-01

    Oil sands processing produces large amounts of waste water that contains polycyclic aromatic hydrocarbons (PAHs) and naphthenic acids (NAs). This study investigated the effects of exposure to PAHs and NA in aquatic organisms. The carbon and nitrogen dynamics in primary producers using stable isotopes in process-affected and reference wetlands were studied. Plankton and periphytic samples from artificial wetland substrates were collected and analyzed. Periphyton was collected in 14 to 20 day intervals for 5 different time periods in 2007 and 2008 in order to analyze seasonal trends in isotopic composition. Results of the study showed d15N enriched values for some consolidated tailings (CT) at sites in 2008. Other sites with mature fine tailings (MFT) as well as non-MFT sites did not have enriched d15N values. The study suggested that there are variations in ammonia levels in the CTs of different oil sands operators. Differences in the quality of the CT resulted in differences in d15N values of the periphyton-dominated by algae as well as in the periphyton dominated by microbes.

  7. Seasonal and spatial trends in production and stable isotope signatures of primary producers in Alberta oil sands reclamation wetlands

    Energy Technology Data Exchange (ETDEWEB)

    Boutsivongsakd, M; Chen, H.; Legg, A.; Farwell, A.; Dixon, G. [Waterloo Univ., ON (Canada)

    2010-07-01

    Oil sands processing produces large amounts of waste water that contains polycyclic aromatic hydrocarbons (PAHs) and naphthenic acids (NAs). This study investigated the effects of exposure to PAHs and NA in aquatic organisms. The carbon and nitrogen dynamics in primary producers using stable isotopes in process-affected and reference wetlands were studied. Plankton and periphytic samples from artificial wetland substrates were collected and analyzed. Periphyton was collected in 14 to 20 day intervals for 5 different time periods in 2007 and 2008 in order to analyze seasonal trends in isotopic composition. Results of the study showed d15N enriched values for some consolidated tailings (CT) at sites in 2008. Other sites with mature fine tailings (MFT) as well as non-MFT sites did not have enriched d15N values. The study suggested that there are variations in ammonia levels in the CTs of different oil sands operators. Differences in the quality of the CT resulted in differences in d15N values of the periphyton-dominated by algae as well as in the periphyton dominated by microbes.

  8. The detection of a synthetic Interleukin-1 receptor antagonist peptide in a seized product from a racing stable.

    Science.gov (United States)

    Levina, Vita; Timms, Mark; Vine, John; Steel, Rohan

    2016-09-01

    A synthetic Interleukin-1 receptor antagonist peptide with the sequence Acetyl-Phe-Glu-Trp-Thr-Pro-Gly-Tyr-Trp-Gln-Pro-Tyr-Ala-Leu-Pro-Leu-OH has been identified in a vial seized during a stable inspection. The use of peptide-based Interleukin-1 receptor antagonists as anti-inflammatory agents has not been previously reported, making this peptide the first in a new class of sports doping peptides. The peptide has been characterized by high-resolution mass spectrometry and a detection method developed based on solid-phase extraction and liquid chromatography - triple quadrupole mass spectrometry. Using in vitro and in vivo models to study the properties of the peptide after administration, the peptide was shown to be highly unstable in plasma and was not detected in urine after administration in a rat. The poor stability of the peptide makes detection challenging but also suggests that it has limited effectiveness as an anti-inflammatory drug. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.

  9. Radiolytic stabilization of industrial poly(methyl methacrylate); Estabilizacao radiolitica do poli(metacrilato de metila) industrial

    Energy Technology Data Exchange (ETDEWEB)

    Aquino, Katia Aparecida da Silva

    2005-03-15

    Poly(methyl methacrylate), PMMA, Acrigel, a Brazilian polymer, is used in the manufacture of medical supplies sterilisable by ionizing radiation. However, when PMMA is gamma-irradiated it undergoes main chain scissions, which promote molecular degradation causing reduction in its physical properties. Therefore, radiolytic stabilization of PMMA is important for to become it commercially radio sterilisable. In this work we investigated the radiolytic stabilization of PMMA by using HALS (Hindered Amine Light Stabilizer) additive, commercially used for photo and thermo oxidative stabilization of polymers. The investigation of the radiation-induced main chain scissions was carried out by viscometric method. The additive added to the polymer system at 0.3 % w/w promotes a molecular radioprotection of 61%. That means a reduction of G value (scissions/100 eV) from 2.6 to 1.0. In addition, the glassy transition temperature (Tg) of PMMA (no additive), significantly changed by radiation, does not change when PMMA (with additive) is irradiated. TGA analysis showed that the additive promotes thermal stability to the system, increasing decomposition temperature of PMMA. Spectroscopy analysis, FT-IR and RMN ({sup 1}H), showed that the radioprotector additive added to the system does not change the PMMA structure. Analysis on mechanical (tensile strength and elongation at break) and optical (yellowness index and refractive index) properties showed a good influence of the additive on polymer system. (author)

  10. Stable particles

    International Nuclear Information System (INIS)

    Samios, N.P.

    1994-01-01

    I have been asked to review the subject of stable particles, essentially the particles that eventually comprised the meson and baryon octets, with a few more additions - with an emphasis on the contributions made by experiments utilizing the bubble chamber technique. In this activity, much work had been done by the photographic emulsion technique and cloud chambers - exposed to cosmic rays as well as accelerator based beams. In fact, many if not most of the stable particles were found by these latter two techniques, however, the foree of the bubble chamber (coupled with the newer and more powerful accelerators) was to verify, and reinforce with large statistics, the existence of these states, to find some of the more difficult ones, mainly neutrals and further to elucidate their properties, i.e., spin, parity, lifetimes, decay parameters, etc. (orig.)

  11. Stable particles

    International Nuclear Information System (INIS)

    Samios, N.P.

    1993-01-01

    I have been asked to review the subject of stable particles, essentially the particles that eventually comprised the meson and baryon octets. with a few more additions -- with an emphasis on the contributions made by experiments utilizing the bubble chamber technique. In this activity, much work had been done by the photographic emulsion technique and cloud chambers-exposed to cosmic rays as well as accelerator based beams. In fact, many if not most of the stable particles were found by these latter two techniques, however, the forte of the bubble chamber (coupled with the newer and more powerful accelerators) was to verify, and reinforce with large statistics, the existence of these states, to find some of the more difficult ones, mainly neutrals and further to elucidate their properties, i.e., spin, parity, lifetimes, decay parameters, etc

  12. Measurements of the radiolytic oxidation of aqueous CsI using a sparging apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Ashmore, C.B.; Brown, D.; Sims, H.E. [AEA Technology, Harwell (United Kingdom); Gwyther, J.R. [NE plc Berkeley Technology Centre, Berkeley (United Kingdom)

    1996-12-01

    Radiolytic oxidation is considered to be the main mechanism for the formation of I{sub 2} from aqueous CsI in containment of a water cooled reactor after a LOCA. Despite the amount of study over the last 60 years on the radiation chemistry of iodine there has been no consistent set of experiments spanning a wide enough range of conditions to verify models with confidence. This paper describes results from a set of experiments carried out in order to remedy this deficiency. In this work the rate of evolution of I{sub 2} from sparged irradiated CsI solution labeled with {sup 131}I was measured on-line over a range of conditions. This work involved the measurement of the effects of pH, temperature, O{sub 2} concentration, I{sup -} concentration, phosphate concentration, dose-rate and impurities on the rate of evolution of I{sub 2}. The range of conditions was chosen in order to span as closely as possible conditions expected in a LOCA but also to help to elucidate some of the mechanisms especially at high pH. pH was found to be a very important factor influencing iodine volatility, over the temperature range studied the extent of oxidation reduced with temperature but this was compensated for by the decrease in partition coefficient. Oxygen concentration was more important in solutions not containing phosphate. The fractional oxidation was not particularly dependent on iodide concentration but G{sub I2} was very dependent on [I{sup -}]. There was no effect of added impurities, Fe, Mn, Mo or organics although in separate work silver was found to have a very important effect. During attempts to interpret the data it was found that it was necessary to include the iodine atom as a volatile species with a partition coefficient of 1.9 taken from thermodynamic data. The modelling work is described in a separate paper. (author) 15 figs., 1 tab., 19 refs.

  13. Degradation of graphite in gas cooled reactors due to radiolytic oxidation

    International Nuclear Information System (INIS)

    Moskovic, R.

    2014-01-01

    Magnox reactors employ pile grade A (PGA) graphite as a moderator. Reactor cores are constructed typically of twelve to thirteen layers of graphite bricks. Fuel channels (FC) are in the centre of all bricks and interstitial channels (IC) at the centre of the corners of every second set of four bricks. The reactor core is cooled by carbon dioxide, the temperature of graphite core increases from 250 °C at the bottom to 360 °C at the top of the core. The neutron dose increases progressively with the operating time of the reactor. The graphite core looses mass as a result of radiolytic oxidation. The process is dependent on both total energy deposition and temperature which correlates with core height. Fast neutron dose accumulates at the same rate as the total energy deposited and is readily available. The reduction of density of moderator graphite increases the porosity and in turn changes both the physical and mechanical properties of graphite. The mechanical properties and density of graphite are measured either on samples installed in the reactor prior to service or trepanned from graphite bricks. The data obtained on these samples are interrogated using probability modelling to establish trends with increasing service life. Results of the analyses are illustrated in the paper. PGA graphite is an aggregate of coarse needle coke filler particles within a matrix of fine coke flour particles mixed with pitch binder. The bricks are fabricated in the green condition by extrusion of dry calcinated coke impregnated with liquid pitch binder and then graphitized at 2800 °C. This produces a polygranular aggregate with orthotropic properties. The strength properties of graphite are measured using different types of tests. The most commonly used tests involve bending, uniaxial and diametral compression. The initiation and propagation of cracks was investigated to improve understanding of strength behaviour. Cracking was examined on macro-scale using optical microscopy and

  14. Methylamphetamine synthesis: does an alteration in synthesis conditions affect the δ(13) C, δ(15) N and δ(2) H stable isotope ratio values of the product?

    Science.gov (United States)

    Salouros, Helen; Collins, Michael; Cawley, Adam; Longworth, Mitchell

    2012-05-01

    Conventional chemical profiling of methylamphetamine has long been employed by national forensic laboratories to determine the synthetic route and where possible the precursor chemicals used in its manufacture. This laboratory has been studying the use of stable isotope ratio mass spectrometry (IRMS) analysis as a complementary technique to conventional chemical profiling of fully synthetic illicit drugs such as methylamphetamine. As part of these investigations the stable carbon (δ(13) C), nitrogen (δ(15) N), and hydrogen (δ(2) H) isotope values in the precursor chemicals of ephedrine and pseudoephedrine and the resulting methylamphetamine end-products have been measured to determine the synthetic origins of methylamphetamine. In this study, results are presented for δ(13) C, δ(15) N, and δ(2) H values in methylamphetamine synthesized from ephedrine and pseudoephedrine by two synthetic routes with varying experimental parameters. It was demonstrated that varying parameters, such as stoichiometry, reaction temperature, reaction time, and reaction pressure, had no effect on the δ(13) C, δ(15) N, and δ(2) H isotope values of the final methylamphetamine product, within measurement uncertainty. Therefore the value of the IRMS technique in identifying the synthetic origin of precursors, such as ephedrine and pseudoephedrine, is not compromised by the potential variation in synthetic method that is expected from one batch to the next, especially in clandestine laboratories where manufacture can occur without stringent quality control of reactions. Copyright © 2011 John Wiley & Sons, Ltd.

  15. Combining functional weed ecology and crop stable isotope ratios to identify cultivation intensity: a comparison of cereal production regimes in Haute Provence, France and Asturias, Spain.

    Science.gov (United States)

    Bogaard, Amy; Hodgson, John; Nitsch, Erika; Jones, Glynis; Styring, Amy; Diffey, Charlotte; Pouncett, John; Herbig, Christoph; Charles, Michael; Ertuğ, Füsun; Tugay, Osman; Filipovic, Dragana; Fraser, Rebecca

    This investigation combines two independent methods of identifying crop growing conditions and husbandry practices-functional weed ecology and crop stable carbon and nitrogen isotope analysis-in order to assess their potential for inferring the intensity of past cereal production systems using archaeobotanical assemblages. Present-day organic cereal farming in Haute Provence, France features crop varieties adapted to low-nutrient soils managed through crop rotation, with little to no manuring. Weed quadrat survey of 60 crop field transects in this region revealed that floristic variation primarily reflects geographical differences. Functional ecological weed data clearly distinguish the Provence fields from those surveyed in a previous study of intensively managed spelt wheat in Asturias, north-western Spain: as expected, weed ecological data reflect higher soil fertility and disturbance in Asturias. Similarly, crop stable nitrogen isotope values distinguish between intensive manuring in Asturias and long-term cultivation with minimal manuring in Haute Provence. The new model of cereal cultivation intensity based on weed ecology and crop isotope values in Haute Provence and Asturias was tested through application to two other present-day regimes, successfully identifying a high-intensity regime in the Sighisoara region, Romania, and low-intensity production in Kastamonu, Turkey. Application of this new model to Neolithic archaeobotanical assemblages in central Europe suggests that early farming tended to be intensive, and likely incorporated manuring, but also exhibited considerable variation, providing a finer grained understanding of cultivation intensity than previously available.

  16. Co-digestion of molasses or kitchen waste with high-rate activated sludge results in a diverse microbial community with stable methane production.

    Science.gov (United States)

    De Vrieze, Jo; Plovie, Kristof; Verstraete, Willy; Boon, Nico

    2015-04-01

    Kitchen waste and molasses are organic waste streams with high organic content, and therefore are interesting substrates for renewable energy production by means of anaerobic digestion. Both substrates, however, often cause inhibition of the anaerobic digestion process, when treated separately, hence, co-digestion with other substrates is required to ensure stable methane production. In this research, A-sludge (sludge harvested from a high rate activated sludge system) was used to stabilize co-digestion with kitchen waste or molasses. Lab-scale digesters were fed with A-sludge and kitchen waste or molasses for a total period of 105 days. Increased methane production values revealed a stabilizing effect of concentrated A-sludge on kitchen waste digestion. Co-digestion of molasses with A-sludge also resulted in a higher methane production. Volumetric methane production rates up to 1.53 L L(-1) d(-1) for kitchen waste and 1.01 L L(-1) d(-1) for molasses were obtained by co-digestion with A-sludge. The stabilizing effect of A-sludge was attributed to its capacity to supplement various nutrients. Microbial community results demonstrated that both reactor conditions and substrate composition determined the nature of the bacterial community, although there was no direct influence of micro-organisms in the substrate itself, while the methanogenic community profile remained constant as long as optimal conditions were maintained. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Impact of radiolysis and radiolytic corrosion on the release of {sup 13}C and {sup 37}Cl implanted into nuclear graphite: Consequences for the behaviour of {sup 14}C and {sup 36}Cl in gas cooled graphite moderated reactors

    Energy Technology Data Exchange (ETDEWEB)

    Moncoffre, N., E-mail: nathalie.moncoffre@ipnl.in2p3.fr [Université de Lyon, Université Lyon 1, CNRS/IN2P3, UMR5822, Institut de Physique Nucléaire de Lyon (IPNL) (France); Toulhoat, N. [Université de Lyon, Université Lyon 1, CNRS/IN2P3, UMR5822, Institut de Physique Nucléaire de Lyon (IPNL) (France); CEA/DEN, Centre de Saclay (France); Bérerd, N.; Pipon, Y. [Université de Lyon, Université Lyon 1, CNRS/IN2P3, UMR5822, Institut de Physique Nucléaire de Lyon (IPNL) (France); Université de Lyon, Université Lyon, IUT Lyon-1 département chimie (France); Silbermann, G. [Université de Lyon, Université Lyon 1, CNRS/IN2P3, UMR5822, Institut de Physique Nucléaire de Lyon (IPNL) (France); EDF – DPI - DIN – CIDEN, DIE - Division Environnement, Lyon (France); Blondel, A. [Université de Lyon, Université Lyon 1, CNRS/IN2P3, UMR5822, Institut de Physique Nucléaire de Lyon (IPNL) (France); Andra, Châtenay-Malabry (France); Galy, N. [Université de Lyon, Université Lyon 1, CNRS/IN2P3, UMR5822, Institut de Physique Nucléaire de Lyon (IPNL) (France); EDF – DPI - DIN – CIDEN, DIE - Division Environnement, Lyon (France); and others

    2016-04-15

    Graphite finds widespread use in many areas of nuclear technology based on its excellent moderator and reflector qualities as well as its strength and high temperature stability. Thus, it has been used as moderator or reflector in CO{sub 2} cooled nuclear reactors such as UNGG, MAGNOX, and AGR. However, neutron irradiation of graphite results in the production of {sup 14}C (dose determining radionuclide) and {sup 36}Cl (long lived radionuclide), these radionuclides being a key issue regarding the management of the irradiated waste. Whatever the management option (purification, storage, and geological disposal), a previous assessment of the radioactive inventory and the radionuclide's location and speciation has to be made. During reactor operation, the effects of radiolysis are likely to promote the radionuclide release especially at the gas/graphite interface. Radiolysis of the coolant is mainly initiated through γ irradiation as well as through Compton electrons in the graphite pores. Radiolysis can be simulated in laboratory using γ irradiation or ion irradiation. In this paper, {sup 13}C, {sup 37}Cl and {sup 14}N are implanted into virgin nuclear graphite in order to simulate respectively the presence of {sup 14}C, {sup 36}Cl and nitrogen, a {sup 14}C precursor. Different irradiation experiments were carried out using different irradiation devices on implanted graphite brought into contact with a gas simulating the coolant. The aim was to assess the effects of gas radiolysis and radiolytic corrosion induced by γ or He{sup 2+} irradiation at the gas/graphite interface in order to evaluate their role on the radionuclide release. Our results allow inferring that radiolytic corrosion has clearly promoted the release of {sup 14}C, {sup 36}Cl and {sup 14}N located at the graphite brick/gas interfaces and open pores.

  18. Accounting for cyanide and its degradation products at three Nevada gold mines; constraints from stable C- and N-isotopes

    Science.gov (United States)

    Johnson, C.A.; Grimes, D.J.; Rye, R.O.

    1998-01-01

    An understanding of the fate of cyanide (CN-) in mine process waters is important for addressing environmental concerns and for taking steps to minimize reagent costs. The utility of stable isotope methods in identifying cyanide loss pathways has been investigated in case studies at three Nevada gold mines. Freshly prepared barren solutions at the mines have cyanide d15N and d13C values averaging -4 ? and -36 ?, respectively, reflecting the nitrogen and carbon sources used by commercial manufacturers, air and natural gas methane. Pregnant solutions returning from ore heaps display small isotopic shifts to lower d15N and d13C values. The shifts are similar to those observed in laboratory experiments where cyanide was progressively precipitated as a cyanometallic compound, and are opposite in sign and much smaller in magnitude than the shifts observed in experiments where HCN was offgassed. Offgassing is inferred to be a minor cyanide loss mechanism in the heap leach operations at the three mines, and precipitation as cyanometallic compounds, and possibly coprecipitation with ferric oxides, is inferred to be an important loss mechanism. Isotopic analysis of dissolved inorganic carbon (DIC) shows that uptake of high d13C air CO2 has been important in many barren and pregnant solutions. However, DIC in reclaim pond waters at all three mines has low d13C values of -28 to -34 ? indicating cyanide breakdown either by hydrolysis or by other chemical pathways that break the C-N bond. Isotope mass balance calculations indicate that about 40 % of the DIC load in the ponds, at a minimum, was derived from cyanide breakdown. This level of cyanide hydrolysis accounts for 14-100 % of the dissolved inorganic nitrogen species present in the ponds. Overall, isotope data provide quantitative evidence that only minor amounts of cyanide are lost via offgassing and that significant amounts are destroyed via hydrolysis and related pathways. The data also highlight the possibility that

  19. Hydrolytic and radiolytic degradation of TBP in TBP.30% V/V-dodecane/UO2(NO3)2.HNO3.H2O systems

    International Nuclear Information System (INIS)

    Barreta, L.G.

    1980-01-01

    The hydrolytic and radiolytic degradation of TBP is investigated in systems of TBP 30% V/V-dodecane/H 2 O . HNO 3 . UO 2 (NO 3 ) 2 by gas chromatographic determination of HDBP. No direct relation between the concentration of HDBP formed and the quantity of HNO 3 extracted by the organic phase is observed in the studies of hydrolysis of TBP. The HDBP concentration is seen to increase non-linearly with the concentration of HNO 3 extracted by the organic phase. Radiolytic studies show that for doses greater than 1 Wh/l, the concentration of HDBP formed increases with the dose absorbed by the system. Whith doses smaller than 1 Wh/l and acid concentration greater than 2 M, two distinct patterns of behavior are observed. The concentration of HDBP as a function of the radiation dose absorbed by the system presents a minimum for uranyl nitrate concentrations smaller than 0.9 M; for uranyl nitrate concentrations greater than 1.3 M the concentration of radiolytic HDBP cannot be calculated because the concentration of the hydrolytic HDBP determined is greater than the sum of the experimental concentrations of hydrolytic and radiolytic HDBP. It is known that the dose absorbed by the process solutions during the reprocessing of light water reactor fuel elements is smaller than one Wh/l. Thus, dose rates between zero and one Wh/l should be studied for this system. (Author) [pt

  20. Stable beams

    CERN Multimedia

    2015-01-01

    Stable beams: two simple words that carry so much meaning at CERN. When LHC page one switched from "squeeze" to "stable beams" at 10.40 a.m. on Wednesday, 3 June, it triggered scenes of jubilation in control rooms around the CERN sites, as the LHC experiments started to record physics data for the first time in 27 months. This is what CERN is here for, and it’s great to be back in business after such a long period of preparation for the next stage in the LHC adventure.   I’ve said it before, but I’ll say it again. This was a great achievement, and testimony to the hard and dedicated work of so many people in the global CERN community. I could start to list the teams that have contributed, but that would be a mistake. Instead, I’d simply like to say that an achievement as impressive as running the LHC – a machine of superlatives in every respect – takes the combined effort and enthusiasm of everyone ...

  1. Water Ice Radiolytic O2, H2, and H2O2 Yields for Any Projectile Species, Energy, or Temperature: A Model for Icy Astrophysical Bodies

    Science.gov (United States)

    Teolis, B. D.; Plainaki, C.; Cassidy, T. A.; Raut, U.

    2017-10-01

    O2, H2, and H2O2 radiolysis from water ice is pervasive on icy astrophysical bodies, but the lack of a self-consistent, quantitative model of the yields of these water products versus irradiation projectile species and energy has been an obstacle to estimating the radiolytic oxidant sources to the surfaces and exospheres of these objects. A major challenge is the wide variation of O2 radiolysis yields between laboratory experiments, ranging over 4 orders of magnitude from 5 × 10-7 to 5 × 10-3 molecules/eV for different particles and energies. We revisit decades of laboratory data to solve this long-standing puzzle, finding an inverse projectile range dependence in the O2 yields, due to preferential O2 formation from an 30 Å thick oxygenated surface layer. Highly penetrating projectile ions and electrons with ranges ≳30 Å are therefore less efficient at producing O2 than slow/heavy ions and low-energy electrons (≲ 400 eV) which deposit most energy near the surface. Unlike O2, the H2O2 yields from penetrating projectiles fall within a comparatively narrow range of (0.1-6) × 10-3 molecules/eV and do not depend on range, suggesting that H2O2 forms deep in the ice uniformly along the projectile track, e.g., by reactions of OH radicals. We develop an analytical model for O2, H2, and H2O2 yields from pure water ice for electrons and singly charged ions of any mass and energy and apply the model to estimate possible O2 source rates on several icy satellites. The yields are upper limits for icy bodies on which surface impurities may be present.

  2. Role of e{sub aq}{sup −}, ·OH and H· in radiolytic degradation of atrazine: A kinetic and mechanistic approach

    Energy Technology Data Exchange (ETDEWEB)

    Khan, Javed Ali, E-mail: javed_chemistry@yahoo.com [Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry, University of Peshawar, Peshawar 25120 (Pakistan); Shah, Noor S. [Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry, University of Peshawar, Peshawar 25120 (Pakistan); Institute of Chemical Sciences, University of Swat, Swat 19130 (Pakistan); Nawaz, Shah; Ismail, M.; Rehman, Faiza [Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry, University of Peshawar, Peshawar 25120 (Pakistan); Khan, Hasan M., E-mail: hmkhan@upesh.edu.pk [Radiation Chemistry Laboratory, National Centre of Excellence in Physical Chemistry, University of Peshawar, Peshawar 25120 (Pakistan)

    2015-05-15

    Highlights: • Atrazine was efficiently removed from aqueous solution by γ-ray irradiation. • e{sub aq}{sup −} was found to have more crucial role in removal of atrazine than ·OH. • Atrazine degradation was reduced in the presence of t-BuOH and i-PrOH. • Atrazine showed high stability at neutral pH than at very low and high pH conditions. • Potential degradation mechanism was evaluated by GC–MS analysis. - Abstract: The degradation of atrazine was investigated in aqueous solution by gamma-ray irradiation. 8.11 μM initial atrazine concentration could be completely removed in N{sub 2} saturated solution by applying 3500 Gy radiation dose at a dose rate of 296 Gy h{sup −1}. Significant removal of atrazine (i.e., 39.4%) was observed at an absorbed dose of 1184 Gy in air saturated solution and the removal efficiency was promoted to 50.5 and 65.4% in the presence of N{sub 2}O and N{sub 2} gases, respectively. The relative contributions of hydrated electron, hydroxyl radical and hydrogen radical toward atrazine degradation were determined as ratio of observed dose constant (k{sub obs}) and found to be 5: 3: 1 for k{sub eaq}{sup −}: k{sub ·OH}: k{sub H}·, respectively. The degradation efficiency of atrazine was 69.5, 55.6 and 37.3% at pH 12.1, 1.7 and 5.7, respectively. A degradation mechanism was proposed based on the identified degradation by-products by gas chromatography–mass spectrometry. Taking the relative contributions of oxidative and reductive species to atrazine degradation into account, reductive pathway proved to be a better approach for the radiolytic treatment of atrazine contaminated water.

  3. Batch and continuous production of stable dense suspensions of drug nanoparticles in a wet stirred media mill

    Science.gov (United States)

    Afolabi, Afola we mi

    One way to improve the bioavailability of poorly water-soluble drugs is to reduce particle size of drug crystals down to nanoscale via wet stirred media milling. An increase in total surface area per mass loading of the drug and specific surface area as well as reduced external mass transfer resistance allow a faster dissolution of the poorly-water soluble drug from nanocrystals. To prevent aggregation of nanoparticles, polymers and surfactants are dissolved in water acting as stabilizers via adsorption onto the drug crystals. In the last two decades, ample experimental data were generated in the area of wet stirred media milling for the production of drug nanoparticle suspensions. However, a fundamental scientific/engineering understanding of various aspects of this process is still lacking. These challenges include elucidation of the governing mechanism(s) during nanoparticle formation and physical stabilization of the nanosuspension with the use of polymers and surfactants (formulation parameters), understanding the impact of process parameters in the context of first-principle-based models, and production of truly nanosized drug particles (10-100 nm) with acceptable physical stability and minimal contamination with the media. Recirculation mode of milling operation, where the drug suspension in a holding tank continuously circulates through the stirred media mill, has been commonly used in lab, pilot, and commercial scales. Although the recirculation is continuous, the recirculation operation mode is overall a batch operation, requiring significant number of batches for a large-volume pharmaceutical product. Hence, development and investigation of a truly continuous process should offer significant advantages. To explain the impact of some of the processing parameters, stress intensity and stress number concepts were widely used in literature, which do not account for the effect of suspension viscosity explicitly. The impact of the processing parameters has not

  4. Experimental determination and chemical modelling of radiolytic processes at the spent fuel/water interface. Long contact time experiments

    International Nuclear Information System (INIS)

    We report on the last experimental and modelling results of a research programme that started in 1995, corresponding in that case to the long contact time experiments. The aim of this programme has been to understand the processes that control the radiolytic generation of oxidants and reductants at the spent fuel water interface and their consequences for spent fuel stability and radionuclide release. The results of this work have been reported in different papers and technical reports during the last decade. In this series, well controlled dissolution experiments of PWR Ringhals spent fuel fragments in an initially anoxic closed system and by using different solution compositions have been carried out, the experiments have been opened after a long time period (between 1.5 and 3 years), samples have been taken and gas and solution analyses have been performed. The results indicate the following: Hydrogen and oxygen concentrations follow the same trend, an initial increase of the concentration of both compounds with time until they reach a steady state that indicates an overall balance of all the radiolytic species generated in the system. Hydrogen peroxide data show in general an initial decrease with time until it reaches a steady state for a given solution composition. This confirms the overall balance of the generated radiolytic species. The experimental data shows that uranium dissolution is controlled by the oxidation of the UO 2 matrix in 10 mM bicarbonate solutions while in the rest of the tests carried out at lower or in the absence of carbonate, uranium in the aqueous phase is governed by the precipitation of schoepite. These processes control the co-dissolution of most of the analysed radionuclides, including Sr, Cs, Mo, Tc and Np while not a clear dependency is found for Pu, Y, and Nd suggesting that other processes are governing the concentration of these radionuclides in the aqueous phase. Kinetic modelling has been performed with data from experiments

  5. Form-stable crystalline polymer pellets for thermal energy storage: high density polyethylene intermediate products. Final report, October 1, 1977--January 31, 1978

    Energy Technology Data Exchange (ETDEWEB)

    Botham, R.A.; Ball, G.L. III; Jenkins, G.H.; Salyer, I.O.

    1978-01-01

    The primary objectives of this program were to demonstrate: (1) that form-stable high density polyethylene (HDPE), which has been shown to have desirable properties as a phase-change type of thermal energy storage material, could be produced by processing in a polyethylene plant for a projected price near 26 cents/lb; and (2) that the raw material, ethylene, will be available in the very long-term from alternate sources (other than petroleum and natural gas). These objectives were accomplished. Production of useful, form-stable HDPE pellets by radiation cross-linking was demonstrated. Such pellets are estimated to be obtainable at 26 cents/lb, using large-volume (> or equal to 10,000,000 lb/yr) in-plant processing. Well-developed technologies exist for obtaining ethylene from coal and plant (or biomass) sources, thus assuring its long-term availability and therefore that of polyethylene. A cost-benefit analysis of the HDPE thermal energy storage system was conducted over its 120 to 140/sup 0/C optimum operating range which is most suited for absorption air conditioning. The HDPE is more cost effective than either rocks, ethylene glycol, or pressurized water and is even competitive with a hypothetical 5 cents/lb salt-hydrate melting in this temperature range. These results applied, as appropriate, to both air and liquid transfer systems.

  6. Submicron sized water-stable metal organic framework (bio-MOF-11) for catalytic degradation of pharmaceuticals and personal care products.

    Science.gov (United States)

    Azhar, Muhammad Rizwan; Vijay, Periasamy; Tadé, Moses O; Sun, Hongqi; Wang, Shaobin

    2018-04-01

    Water-stable and active metal organic frameworks (MOFs) are important materials for mitigation of water contaminants via adsorption and catalytic reactions. In this study, a highly water-stable Co-based MOF, namely bio-MOF-11-Co, was synthesized by a simplified benign method. Moreover, it was used as a catalyst in successful activation of peroxymonsulfate for catalytic degradation of sulfachloropyradazine (SCP) and para-hydroxybenzoic acid (p-HBA) as representatives of pharmaceuticals and personal care products, respectively. The bio-MOF-11-Co showed rapid degradation of both p-HBA and SCP and could be reused multiple times without losing the activity by simply water washing. The effects of catalyst and PMS loadings as well as temperature were further studied, showing that high catalyst and PMS loadings as well as temperature produced faster kinetic degradation of p-HBA and SCP. The generation of highly reactive and HO radicals during the degradation was investigated by quenching tests and electron paramagnetic resonance. A plausible degradation mechanism was proposed based on the functionalities in the bio-MOF-11-Co. The availability of electron rich nucleobase adenine reinforced the reaction kinetics by electron donation along with cobalt atoms in the bio-MOF-11-Co structure. Copyright © 2017 Elsevier Ltd. All rights reserved.

  7. The $1^{+}\\to n^{+}$ charge breeding method for the production of radioactive and stable continuous /pulsed multi-chargedion beams

    CERN Document Server

    Chauvin, N; Bouly, J L; Curdy, Jean Claude; Geller, R; Lamy, T; Solé, P; Sortais, P

    1999-01-01

    The principle of the 1+ -> n+ charge breeding method by injecting a mono-charged ion beam in an Electron Cyclotron Resonance Ion Source is recalled. Some 1+ ->n+ breeding efficiencies in continuous mode are given, like 9% for Ar1+ ->Ar8+ and 5% for Rb1+->Rb15+. The global capture efficiency is deduced from the whole charge state distribution spectrum. The ECRIT (ECR Ion Trap) mode that allows to produce a pulsed multi-charged beam is explained. The n+ ions are extracted in a 20 ms pulse. The breeding-bunching efficiencies are measured for Rb1+->Rb15+ (2.2%) and Pb1+->Pb22+ (1.3 %). Ion trapping time in the ECRIT plasma is evaluated to some hundreds of ms. A new application of the 1+->n+ method is developed: the production of multi-charged natural metallic ions. First experiments have been done on uranium: a 500 nA continuous current of U26+ has been measured. Finally, the future developments on the 1+->n+ experiment are discussed. A description of a 1+ ->n+ dedicated high performance ECRIS named PHOENIX (Prod...

  8. Production of putrescine-capped stable silver nanoparticle: its characterization and antibacterial activity against multidrug-resistant bacterial strains

    Science.gov (United States)

    Saha, Saswati; Gupta, Bhaskar; Gupta, Kamala; Chaudhuri, Mahua Ghosh

    2016-11-01

    Integration of biology with nanotechnology is now becoming attention-grabbing area of research. The antimicrobial potency of silver has been eminent from antiquity. Due to the recent desire for the enhancement of antibacterial efficacy of silver, various synthesis methods of silver in their nano dimensions are being practiced using a range of capping material. The present work highlights a facile biomimetic approach for production of silver nanoparticle being capped and stabilized by putrescine, possessing a diameter of 10-25 ± 1.5 nm. The synthesized nanoparticles have been analyzed spectrally and analytically. Morphological studies are carried out by high-resolution transmission electron microscopy and crystallinity by selected area electron diffraction patterns. Moreover, the elemental composition of the capped nanoparticles was confirmed by energy-dispersive X-ray spectroscopy analysis. A comparative study (zone of inhibition and minimum inhibitory concentration) regarding the interactions and antibacterial potentiality of the capped silver nanoparticles with respect to the bare ones reveal the efficiency of the capped one over the bare one. The bacterial kinetic study was executed to monitor the interference of nanoparticles with bacterial growth rate. The results also highlight the efficacy of putrescine-capped silver nanoparticles as effective growth inhibitors against multi-drug resistant human pathogenic bacterial strains, which may, thus, potentially be applicable as an effective antibacterial control system to fight diseases.

  9. Stable isotope approach to fission product element studies of soil-to-plant transfer and in vitro modelling of ruminant digestion using inductively coupled plasma mass spectrometry

    International Nuclear Information System (INIS)

    Robb, Paul; Owen, L.M.W.; Crews, H.M.

    1995-01-01

    A stable isotope approach has been used to investigate two aspects of the behaviour of fission product elements in the environment and food chains using inductively coupled plasma mass spectrometry (ICP-MS). Limits of detection (dry mass LODs) of 0.053 mg kg -1 for Sr, 0.011 mg kg -1 for Cs and 0.084 mg kg -1 for Ce were low enough to allow the determination of soil-to-plant transfer factors for soft fruit and the application of the approach to an in vitro model of ruminant digestion. The multi-element measurement capability of ICP-MS also permitted the analysis of selected nutrients, including zinc, in in vitro experiments. (author)

  10. Development of a hydrophobic catalyst for recombining radiolytically generated H2 and O2 in nuclear reactors

    International Nuclear Information System (INIS)

    Belapurkar, A.D.; Gupta, N.M.

    2000-01-01

    A catalyst is developed for efficient recombination of H 2 and O 2 in presence of water vapor and without requirement of an external heat source. The catalyst, comprising of finely dispersed platinum on a large area polymeric support, is hydrophobic in nature and is therefore resistant to water poisoning. The exothermicity of H 2 -O 2 reaction results in the rise of catalyst temperature and hence in its high and sustained catalytic activity. In order to prevent its over-heating, the catalyst sheet is sandwiched between the two metallic plates which also help in maintaining the catalyst panel at an isothermal temperature. The performance of this catalyst, evaluated both on bench and pilot plant scale, is found to be long lasting. Due to the flexible nature of this catalyst material, different convenient reactor designs may be envisaged for use in nuclear reactors for recombining radiolytically generated H 2 and O 2 . (author)

  11. Improved production and characterization of a highly stable laccase from the halophilic bacterium Chromohalobacter salexigens for the efficient delignification of almond shell bio-waste.

    Science.gov (United States)

    Jafari, Nasrin; Rezaei, Shahla; Rezaie, Rezvan; Dilmaghani, Haleh; Khoshayand, Mohammad Reza; Faramarzi, Mohammad Ali

    2017-12-01

    Extremozymes have gained importance for their ability to efficiently develop the processes in rigorous industrial conditions with incidence in the recycling of especially robust natural wastes. The production of an extracellular laccase from the halophilic bacterium Chromohalobacter salexigens aided for the bio-delignification of almond shell was optimized using response surface methodology followed by one-factor-at-a-time, resulting in an 80-fold increase in the enzyme yield. Out of 10 different medium components, CuSO 4 , ZnSO 4 , glucose, and urea were shown to have the greatest effects on the laccase production. The crude laccase was surprisingly stable against the various solvents, salts, chemicals, pH ranges, and temperatures, and it exhibited a high catalytic efficiency to a wide range of phenolic and non-phenolic substrates. Laccase reduced the kappa number of the lignin of almond shell by approximately 27% without the aid of a mediator, and the delignification efficiency strengthened by up to 58% reduction in kappa number in the used harsh conditions. Due to the high potential of the enzyme in delignification, specifically under extreme conditions, laccase from C. salexigens can be considered as an ideal alternative for chemical treatment methods in cellulose fibres extraction of lignocellulosic bio-wastes or delignification of the lignin and lignin-derived industrial wastes. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Stable production of human insulin-like growth factor 1 (IGF-1) in the milk of hemi- and homozygous transgenic rabbits over several generations.

    Science.gov (United States)

    Zinovieva, N; Lassnig, C; Schams, D; Besenfelder, U; Wolf, E; Müller, S; Frenyo, L; Seregi, J; Müller, M; Brem, G

    1998-11-01

    One transgenic rabbit line was generated carrying a fusion gene consisting of the cDNA for human IGF-1 fused to a mammary gland specific expression cassette derived from bovine alpha-S1-casein sequences. Transgene expression was shown to be strictly tissue and lactation period specific. The transgenic rabbit line was bred for six generations. All transgenic animals showed stable production of biologically active IGF-1 over the generations and no apparent effect on the physiological or reproductive performance was observed. The absence of adverse effects on homozygous transgenic rabbits suggested the absence of insertional mutagenesis. Eight hemizygous transgenic offspring analysed produced on average 363 +/- 12 micrograms/ml (ranging from 223 +/- 61 to 484 +/- 39 micrograms/ml) mature human IGF-1 in their milk, whereas three homozygous animals produced on average 543 +/- 41 micrograms/ml (ranging from 360 +/- 15 to 678 +/- 80 micrograms/ml). Homozygous hulGF-1 females clearly showed a significantly increased production performance of the recombinant protein.

  13. Fusion of the Dhfr/Mtx and IR/MAR gene amplification methods produces a rapid and efficient method for stable recombinant protein production.

    Science.gov (United States)

    Noguchi, Chiemi; Araki, Yoshio; Miki, Daisuke; Shimizu, Noriaki

    2012-01-01

    Amplification of the dihydrofolate reductase gene (Dhfr) by methotrexate (Mtx) exposure is commonly used for recombinant protein expression in Chinese hamster ovary (CHO) cells. However, this method is both time- and labor-intensive, and the high-producing cells that are generated are frequently unstable in culture. Another gene amplification method is based on using a plasmid bearing a mammalian replication initiation region (IR) and a matrix attachment region (MAR), which result in the spontaneous initiation of gene amplification in transfected cells. The IR/MAR and Dhfr/Mtx methods of gene amplification are based on entirely different principles. In this study, we combine these two methods to yield a novel method, termed the IR/MAR-Dhfr fusion method, which was used to express three proteins, the Fc receptor, GFP, and recombinant antibody. The fusion method resulted in a dramatic increase in expression of all three proteins in two CHO sub-lines, DXB-11, and DG44. The IR/MAR-Dhfr fusion amplified the genes rapidly and efficiently, and produced larger amounts of antibody than the Dhfr/Mtx or IR/MAR methods alone. While the amplified structure produced by the Dhfr/Mtx method was highly unstable, and the antibody production rate rapidly decreased with the culture time of the cells, the IR/MAR-Dhfr fusion method resulted in stable amplification and generated clonal cells that produced large amounts of antibody protein over a long period of time. In summary, the novel IR/MAR-Dhfr fusion method enables isolation of stable cells that produce larger amounts of a target recombinant protein more rapidly and easily than either the Dhfr/Mtx or IR/MAR methods alone.

  14. Production and Properties of a Thermostable, pH—Stable Exo-Polygalacturonase Using Aureobasidium pullulans Isolated from Saharan Soil of Algeria Grown on Tomato Pomace

    Directory of Open Access Journals (Sweden)

    Leila Bennamoun

    2016-10-01

    Full Text Available Polygalacturonase is a valuable biocatalyst for several industrial applications. Production of polygalacturonase using the Aureobasidium pullulans stain isolated from Saharan soil of Algeria was investigated. Its capacity to produce polygalacturonase was assessed under submerged culture using tomato pomace as an abundant agro-industrial substrate. Optimization of the medium components, which enhance polygalacturonase activity of the strain Aureobasidium pullulans, was achieved with the aid of response surface methodology. The composition of the optimized medium was as follows: tomato pomace 40 g/L, lactose 1.84 g/L, CaCl20.09 g/L and pH 5.16. Practical validation of the optimum medium provided polygalacturonase activity of 22.05 U/mL, which was 5-fold higher than in unoptimized conditions. Batch cultivation in a 20 L bioreactor performed with the optimal nutrients and conditions resulted in a high polygalacturonase content (25.75 U/mL. The enzyme showed stability over a range of temperature (5–90 °C with an optimum temperature of 60 °C with pH 5.0, exhibiting 100% residual activity after 1h at 60 °C. This enzyme was stable at a broad pH range (5.0–10. The enzyme proved to be an exo-polygalacturonase, releasing galacturonic acid by hydrolysis of polygalacturonic acid. Moreover, the exo-polygalacturonase was able to enhance the clarification of both apple and citrus juice. As a result, an economical polygalacturonase production process was defined and proposed using an industrial food by-product.

  15. Process intensification for high yield production of influenza H1N1 Gag virus-like particles using an inducible HEK-293 stable cell line.

    Science.gov (United States)

    Venereo-Sanchez, Alina; Simoneau, Melanie; Lanthier, Stéphane; Chahal, Parminder; Bourget, Lucie; Ansorge, Sven; Gilbert, Rénald; Henry, Olivier; Kamen, Amine

    2017-07-24

    Influenza virus dominant antigens presentation using virus like particle (VLP) approach is attractive for the development of new generation of influenza vaccines. Mammalian cell platform offers many advantages for VLP production. However, limited attention has been paid to the processing of mammalian cell produced VLPs. Better understanding of the production system could contribute to increasing the yields and making large-scale VLP vaccine manufacturing feasible. In a previous study, we have generated a human embryonic kidney HEK-293 inducible cell line expressing Hemagglutinin (HA) and Neuraminidase (NA), which was used to produce VLPs upon transient transfection with a plasmid containing HIV-1 Gag. In this work, to streamline the production process, we have developed a new HEK-293 inducible cell line adapted to suspension growth expressing the three proteins HA, NA (H1N1 A/PR/8/1934) and the Gag fused to GFP for monitoring the VLP production. The process was optimized to reach higher volumetric yield of VLPs by increasing the cell density at the time of induction without sacrificing the cell specific productivity. A 5-fold improvement was achieved by doing media evaluation at small scale. Furthermore, a 3-L perfusion bioreactor mirrored the performance of small-scale shake flask cultures with sequential medium replacement. The cell density was increased to 14×10 6 cells/ml at the time of induction which augmented by 60-fold the volumetric yield to 1.54×10 10 Gag-GFP fluorescent events/ml, as measured by flow cytometry. The 9.5-L harvest from the perfusion bioreactor was concentrated by tangential flow filtration at low shear rate. The electron micrographs revealed the presence of VLPs of 100-150nm with the characteristic dense core of HIV-1 particles. The developed process shows the feasibility of producing high quantity of influenza VLPs from an inducible mammalian stable cell line aiming at large scale vaccine manufacturing. Crown Copyright © 2017

  16. A top quark pair production event from proton-proton collisions recorded by ATLAS with LHC stable beams at a collision energy of 13 TeV

    CERN Multimedia

    ATLAS Collaboration

    2015-01-01

    Display of a candidate boosted top quark pair production event from proton-proton collisions recorded by ATLAS with LHC stable beams at a collision energy of 13 TeV. The red line shows the path of a muon with transverse momentum around 50 GeV through the detector. The dashed line shows the direction of the missing transverse momentum, which has a magnitude of about 470 GeV. The green and yellow bars indicate energy deposits in the liquid argon and scintillating-tile calorimeters, from these deposits 4 small-radius (R=0.4) jets are identified with transverse momenta between 70 and 300 GeV. Three of these small-radius jets are re-clustered into the leading large-radius (R=1.0) jet (not shown explicitly) with a transverse momentum of about 600 GeV and a jet mass of about 180 GeV, near the top quark mass. One of these three jets in addition to the fourth jet above 70 GeV are identified as having originated from b-quarks. Tracks reconstructed from hits in the inner tracking detector are shown as arcs curving in th...

  17. Production, Characterization, and Flocculation Mechanism of Cation Independent, pH Tolerant, and Thermally Stable Bioflocculant from Enterobacter sp. ETH-2

    Science.gov (United States)

    Tang, Wei; Song, Liyan; Li, Dou; Qiao, Jing; Zhao, Tiantao; Zhao, Heping

    2014-01-01

    Synthetic high polymer flocculants, frequently utilized for flocculating efficiency and low cost, recently have been discovered as producing increased risk to human health and the environment. Development of a more efficient and environmentally sound alternative flocculant agent is investigated in this paper. Bioflocculants are produced by microorganisms and may exhibit a high rate of flocculation activity. The bioflocculant ETH-2, with high flocculating activity (2849 mg Kaolin particle/mg ETH-2), produced by strain Enterobacter sp. isolated from activated sludge, was systematically investigated with regard to its production, characterization, and flocculation mechanism. Analyses of microscopic observation, zeta potential and ETH-2 structure demonstrates the bridging mechanism, as opposed to charge neutralization, was responsible for flocculation of the ETH-2. ETH-2 retains high molecular weight (603 to 1820 kDa) and multi-functional groups (hydroxyl, amide and carboxyl) that contributed to flocculation. Polysaccharides mainly composed of mannose, glucose, and galactose, with a molar ratio of 1∶2.9∶9.8 were identified as the active constituents in bioflocculant. The structure of the long backbone with active sites of polysaccharides was determined as a primary basis for the high flocculation activity. Bioflocculant ETH-2 is cation independent, pH tolerant, and thermally stable, suggesting a potential fit for industrial application. PMID:25485629

  18. Production, characterization, and flocculation mechanism of cation independent, pH tolerant, and thermally stable bioflocculant from Enterobacter sp. ETH-2.

    Directory of Open Access Journals (Sweden)

    Wei Tang

    Full Text Available Synthetic high polymer flocculants, frequently utilized for flocculating efficiency and low cost, recently have been discovered as producing increased risk to human health and the environment. Development of a more efficient and environmentally sound alternative flocculant agent is investigated in this paper. Bioflocculants are produced by microorganisms and may exhibit a high rate of flocculation activity. The bioflocculant ETH-2, with high flocculating activity (2849 mg Kaolin particle/mg ETH-2, produced by strain Enterobacter sp. isolated from activated sludge, was systematically investigated with regard to its production, characterization, and flocculation mechanism. Analyses of microscopic observation, zeta potential and ETH-2 structure demonstrates the bridging mechanism, as opposed to charge neutralization, was responsible for flocculation of the ETH-2. ETH-2 retains high molecular weight (603 to 1820 kDa and multi-functional groups (hydroxyl, amide and carboxyl that contributed to flocculation. Polysaccharides mainly composed of mannose, glucose, and galactose, with a molar ratio of 1:2.9:9.8 were identified as the active constituents in bioflocculant. The structure of the long backbone with active sites of polysaccharides was determined as a primary basis for the high flocculation activity. Bioflocculant ETH-2 is cation independent, pH tolerant, and thermally stable, suggesting a potential fit for industrial application.

  19. Direct Photolysis of Sulfamethoxazole Using Various Irradiation Sources and Wavelength Ranges-Insights from Degradation Product Analysis and Compound-Specific Stable Isotope Analysis.

    Science.gov (United States)

    Willach, Sarah; Lutze, Holger V; Eckey, Kevin; Löppenberg, Katja; Lüling, Michelle; Wolbert, Jens-Benjamin; Kujawinski, Dorothea M; Jochmann, Maik A; Karst, Uwe; Schmidt, Torsten C

    2018-02-06

    The environmental micropollutant sulfamethoxazole (SMX) is susceptible to phototransformation by sunlight and UV-C light which is used for water disinfection. Depending on the environmental pH conditions SMX may be present as neutral or anionic species. This study systematically investigates the phototransformation of these two relevant SMX species using four different irradiation scenarios, i.e., a low, medium, and high pressure Hg lamp and simulated sunlight. The observed phototransformation kinetics are complemented by data from compound-specific stable isotope and transformation product analysis using isotope-ratio and high-resolution mass spectrometry (HRMS). Observed phototransformation kinetics were faster for the neutral than for the anionic SMX species (from 3.4 (LP lamp) up to 6.6 (HP lamp) times). Furthermore, four phototransformation products (with m/z 189, 202, 242, and 260) were detected by HRMS that have not yet been described for direct photolysis of SMX. Isotopic fractionation occurred only if UV-B and UV-A wavelengths prevailed in the emitted irradiation and was most pronounced for the neutral species with simulated sunlight (ε C = -4.8 ± 0.1 ‰). Phototransformation of SMX with UV-C light did not cause significant isotopic fractionation. Consequently, it was possible to differentiate sunlight and UV-C light induced phototransformation of SMX. Thus, CSIA might be implemented to trace back wastewater point sources or to assess natural attenuation of SMX by sunlight photolysis. In contrast to the wavelength range, pH-dependent speciation of SMX hardly impacted isotopic fractionation.

  20. Authentication of pure L-leucine products manufactured in China by discriminating between plant and animal sources using nitrogen stable isotope technique.

    Science.gov (United States)

    Huang, Jingyu; Nkrumah, Philip N; Appiah-Sefah, Gloria; Tang, Shijiang

    2013-03-01

     L-leucine products among other branched chain amino acid supplements are highly susceptible to economically motivated adulteration. Curbing this menace is critical and timely. Hence, the δ(15) N composition of the L-leucine derived from plants and animals sources was estimated. The trophic enrichment phenomenon of δ(15) N composition was utilized to elucidate the sources. We finally established the distinction between the respective sources. Samples of plant sources (maize and soybean) and that of animal sources (pig fur and duck feather) were analyzed for δ(15) N isotopic signatures. An elemental analyzer which was connected to an isotope ratio mass spectrometer operated in the continuous flow mode was utilized. The raw materials were obtained from China. Statistical analysis was performed using descriptive statistics and one-way analysis of variance. The results indicated lower δ(15) N values of range -0.7344‰ to 2.384‰ and 1.032‰ to 2.064‰ for maize and soybean samples, respectively. Whereas, a range of 3.860‰ to 6.011‰ and 5.875‰ to 6.011‰ was, respectively, detected in pig fur and duck feather samples. The δ(15) N difference in plants and animals samples was significant (F = 165.0; P = 1.675 E-10 for maize and pig fur samples; F = 212.8; P = 0.0001284 for soybean and duck feather samples). It was observed that δ(15) N trophic enrichment is helpful in elucidating the respective sources. The authors can emphatically assert that the range of δ(15) N composition of L-leucine derived from plants sources within the study area is -1.000‰ to 3.000‰ whereas the range in animal sources is 4.000‰ to 9.000‰. Practical Application This study provides a reliable approach in verifying the authenticity of not only L-leucine products but also other branched chain amino acid supplements and thereby would help in fraud detection of any economically motivated adulteration and mislabeling of these products. When coupled with H and O stable

  1. Forensic Stable Isotope Biogeochemistry

    Science.gov (United States)

    Cerling, Thure E.; Barnette, Janet E.; Bowen, Gabriel J.; Chesson, Lesley A.; Ehleringer, James R.; Remien, Christopher H.; Shea, Patrick; Tipple, Brett J.; West, Jason B.

    2016-06-01

    Stable isotopes are being used for forensic science studies, with applications to both natural and manufactured products. In this review we discuss how scientific evidence can be used in the legal context and where the scientific progress of hypothesis revisions can be in tension with the legal expectations of widely used methods for measurements. Although this review is written in the context of US law, many of the considerations of scientific reproducibility and acceptance of relevant scientific data span other legal systems that might apply different legal principles and therefore reach different conclusions. Stable isotopes are used in legal situations for comparing samples for authenticity or evidentiary considerations, in understanding trade patterns of illegal materials, and in understanding the origins of unknown decedents. Isotope evidence is particularly useful when considered in the broad framework of physiochemical processes and in recognizing regional to global patterns found in many materials, including foods and food products, drugs, and humans. Stable isotopes considered in the larger spatial context add an important dimension to forensic science.

  2. Formation of a Colloidal CdSe and ZnSe Quantum Dots via a Gamma Radiolytic Technique

    Directory of Open Access Journals (Sweden)

    Aeshah Salem

    2016-09-01

    Full Text Available Colloidal cadmium selenide (CdSe and zinc selenide (ZnSe quantum dots with a hexagonal structure were synthesized by irradiating an aqueous solution containing metal precursors, poly (vinyl pyrrolidone, isopropyl alcohol, and organic solvents with 1.25-MeV gamma rays at a dose of 120 kGy. The radiolytic processes occurring in water result in the nucleation of particles, which leads to the growth of the quantum dots. The physical properties of the CdSe and ZnSe nanoparticles were measured by various characterization techniques. X-ray diffraction (XRD was used to confirm the nanocrystalline structure, energy-dispersive X-ray spectroscopy (EDX was used to estimate the material composition of the samples, transmission electron microscopy (TEM was used to determine the morphologies and average particle size distribution, and UV-visible spectroscopy was used to measure the optical absorption spectra, from which the band gap of the CdSe and ZnSe nanoparticles could be deduced.

  3. Studies on the thermal and radiolytic resistance of an anion exchanger with benzimidazole functional groups in nitric acid solution

    International Nuclear Information System (INIS)

    Iwasa, Satoru; Murata, Kiyoshi; Takeda, Kunihiko; Arai, Tsuyoshi; Wei, Y.Z.; Kumagai, Mikio

    2001-01-01

    Thermal and radiolytic resistance of AR-01R anion exchanger containing benzimidazole groups as exchange sites in nitric acid solution has been studied. Changes in its exchange capacity (EC), structure and shape were investigated and compared with those of a commercial Amberlite IRA-900 anion exchanger with quaternary ammonium group. Compared to the IRA-900, the AR-01R anion exchanger showed significantly higher thermal resistance and its decrease in EC was less than 10% after immersion in 9 mol·dm -3 solution for 72 h. On the other hand, it was found that the EC decrease of these two anion exchangers induced by γ-ray irradiation was almost the same; their EC decreased by 20-25% after irradiation in 9 mol·dm -3 HNO 3 solution at room temperature with absorption dose of 3.0 MGy. The change of the strong-base benzimidazole group to weak-base benzimidazole group in AR-01 was found to be the main damage by heat and γ-ray irradiation. (author)

  4. Life in Ice: Microbial Growth Dynamics and Greenhouse Gas Production During Winter in a Thermokarst Bog Revealed by Stable Isotope Probing Targeted Metagenomics

    Science.gov (United States)

    Blazewicz, S.; White, R. A., III; Tas, N.; Euskirchen, E. S.; Mcfarland, J. W.; Jansson, J.; Waldrop, M. P.

    2016-12-01

    Permafrost contains a reservoir of frozen C estimated to be twice the size of the current atmospheric C pool. In response to changing climate, permafrost is rapidly warming which could result in widespread seasonal thawing. When permafrost thaws, soils that are rich in ice and C often transform into thermokarst wetlands with anaerobic conditions and significant production of atmospheric CH4. While most C flux research in recently thawed permafrost concentrates on the few summer months when seasonal thaw has occurred, there is mounting evidence that sizeable portions of annual CO2 and CH4 efflux occurs over winter or during a rapid burst of emissions associated with seasonal thaw. A potential mechanism for such efflux patterns is microbial activity in frozen soils over winter where gasses produced are partially trapped within ice until spring thaw. In order to better understand microbial transformation of soil C to greenhouse gas over winter, we applied stable isotope probing (SIP) targeted metagenomics combined with process measurements and field flux data to reveal activities of microbial communities in `frozen' soil from an Alaskan thermokarst bog. Field studies revealed build-up of CO2 and CH4 in frozen soils suggesting that microbial activity persisted throughout the winter in soils poised just below the freezing point. Laboratory incubations designed to simulate in-situ winter conditions (-1.5 °C and anaerobic) revealed continuous CH4 and CO2 production. Strikingly, the quantity of CH4 produced in 6 months in frozen soil was equivalent to approximately 80% of CH4 emitted during the 3 month summer `active' season. Heavy water SIP targeted iTag sequencing revealed growing bacteria and archaea in the frozen anaerobic soil. Growth was primarily observed in two bacterial phyla, Firmicutes and Bacteroidetes, suggesting that fermentation was likely the major C mineralization pathway. SIP targeted metagenomics facilitated characterization of the primary metabolic

  5. Influence of solvent radiolysis on extraction, scrubbing and stripping of uranium and some fission products

    International Nuclear Information System (INIS)

    Gawlowska, W.; Nowak, M.

    1978-01-01

    Radiolytically degraded TBP-n-paraffins solvent was used in the laboratory flow-sheet to study the influence of radiation exposure on decontamination of uranium. The influence of accumulated doses on extraction, scrubbing and stripping of uranium and some fission products has been discussed. (author)

  6. Stable Isotope Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Tissue samples (skin, bone, blood, muscle) are analyzed for stable carbon, stable nitrogen, and stable sulfur analysis. Many samples are used in their entirety for...

  7. Development of detection methods for irradiated foods - Development of detection method for radiolytic products of irradiated foods

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kyong Su; Lee, Eun Ryong; Hong, Hae Jung [Chosun University, Kwangju (Korea)

    2000-07-01

    Meats, nuts, legumes and cereals were irradiated with {sup 60}Co {gamma}-ray. The detection methods included the fat extraction from samples, isolation of hydrocarbons and 2-alkylcyclobutanones by florisil column chromatography and analyses of GC-FID and GC/MS analyzers. Concentrations of hydrocarbons and 2-clobutanones increased with the irradiation dose in meat, nuts, legumes and cereals. In nuts (sesame seeds, black sesame seeds, perilla seeds, pine nuts and peanuts), legumes (white beans, black soybeans, yellow bean sprout soybeans, mouse-eyed soybeans, mung beans, kidney beans and small red beans) and cereals (brown rice, corns and wheat), 8-heptadecene and 1,7-hexadecadiene originated from oleic acid and 6,9-heptadecadiene and 1,7,10-hexadecatriene induced from linoleic acids were the major hydrocarbons due to the composition of fatty acids. Concentrations of radiation-induced hydrocarbons in nuts were slightly reduced and hydrocarbons were still significantly detectable, during 6 months at -18 deg. C. In meats and nuts, 2-(5'-tetradecenyl)cyclobutanone formed from oleic acid was found in most. 2-Dodecylcyclobutanone was detected in a large amount. The concentrations of radiation-induced 2-alkylcyclobutanones in meats slightly decreased, but relatively constant during 6 months at -18 deg. C. 62 refs., 45 figs., 25 tabs. (Author)

  8. Radiolytic syntheses of hollow UO{sub 2} nanospheres in Triton X-100-based lyotropic liquid crystals

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yongming; Chen, Qingde; Shen, Xinghai [Peking Univ., Beijing (China). Fundamental Science on Radiochemistry and Radiation Chemistry Lab.

    2017-08-01

    Hollow nanospheres (φ: 60-80 nm, wall thickness: 10-20 nm), consisted of UO{sub 2} nanoparticles (φ: 3-5 nm), were successfully prepared in a Triton X-100-water (50:50, w/w) hexagonal lyotropic liquid crystal (LLC) by γ-irradiation, where water soluble ammonium uranyl tricarbonate was added as precursor. The product was stable at least up to 300 C. Furthermore, whether the nanospheres were hollow or not, and the wall thickness of the hollow nanospheres could be easily controlled via adjusting dose rate. While in the Triton X-100 based micellar systems, only solid nanospheres were obtained. At last, a possible combination mechanism containing adsorption, aggregation and fracturing processes was proposed.

  9. Impact of herbaceous understory vegetation to ecosystem water cycle, productivity and infiltration in a semi arid oak woodland assessed by stable oxygen isotopes

    Science.gov (United States)

    Dubbert, Maren; Piayda, Arndt; Silva, Filipe Costa e.; Correia, Alexandra C.; Pereira, Joao S.; Cuntz, Matthias; Werner, Christiane

    2015-04-01

    vegetation strongly increased rain infiltration, specifically during strong rain events. In conclusion, beneficial understory vegetation effects were dominant. However, the observed vulnerability of the understory vegetation to drought and competition for water with trees suggests, that increased drought and altered precipitation pattern as predicted in future climate change scenarios for the Mediterranean basin not only threaten understory development. They also very likely decrease rain infiltration and ground water recharge by decreasing understory vegetation cover and increasing amount of heavy precipitation events with high run-off from sealed bare soils. This in turn can severely diminish cork-oak productivity and hence the resilience of the ecosystem toward drought (Costa e Silva et al., in rev.). Dubbert, M; Cuntz, M; Piayda, A; Maguas, C; Werner, C: Partitioning evapotranspiration - Testing the Craig and Gordon model with field measurements of oxygen isotope ratios of evaporative fluxes. J Hydrol (2013) Dubbert, M; Piayda, A; Cuntz, M; Correia, AC; Costa e Silva, F; Pereira, JS; Werner, C: Stable oxygen isotope and flux partitioning demonstrates understory of an oak savanna contributes up to half of ecosystem carbon and water exchange, Frontiers in Plant Science (2014a) Dubbert, M; Mosena, A; Piayda, A; Cuntz, M; Correia, AC; Pereira, JS; Werner, C: Influence of tree cover on herbaceous layer development and carbon and water fluxes in a Portuguese cork oak woodland., Acta Oecologica

  10. Diamex process: hydrolytic and radiolytic degradation of the diamide extractant DMDOHEMA

    International Nuclear Information System (INIS)

    Berthon, L.; Cames, B.

    2000-01-01

    This paper deals with the hydrolysis and radiolysis of a diamide (malonamide) which is the extractant of the DIAMEX process for the extraction of minor actinides from high level liquid radioactive waste. The semi-developed formula of the malonamides investigated is RR'NCO(CHR'')CONRR' (where R, R' and R'' are alkyl or oxy-alkyl groups). The formula of the extractant molecule has been optimized and has led to DMDOHEMA (NN'-dimethyl N,N'-di-octyl hexyl-oxy-ethyl malonamide: (C 8 H 17 (CH 3 )NCO) 2 CH(C 2 H 4 OC 6 H 13 )) which is the present reference extractant for the DIAMEX process. The aim of this study was to: -identify and quantify the main DMDOHEMA degradation products; - identify the potential degradation pathways for diamides; -correlate the concentration of the identified degradation products with the extracting properties of the spent solvents to identify the most disturbing degradation products. (authors)

  11. Radiolytic Effects on Fluoride Impurities in a U{sub 3}O{sub 8} Matrix

    Energy Technology Data Exchange (ETDEWEB)

    Icenhour, A.S.

    2000-05-01

    The safe handling and storage of radioactive materials require an understanding of the effects of radiolysis on those materials. Radiolysis may result in the production of gases (e.g., corrosives) or pressures that are deleterious to storage containers. A study has been performed to address these concerns as they relate to the radiolysis of residual fluoride compounds in uranium oxides.

  12. The transient reaction characteristic of piperonal and anthraquinone derivative: a pulse radiolytic study

    International Nuclear Information System (INIS)

    Ma Jianhua; Lin Weizhen; Wang Wenfeng; Yao Side

    2006-01-01

    Piperonal belongs to naturally organic compound and anthraquinone-2-sulfate is a important anthraquinone derivative. In this work, the transient reaction characteristic of piperonal and anthraquinone derivative has been investigated. The transient absorption spectra of the product from electron transfer reaction between piperonal and anthraquinone-2-sulfate was obtained, the electron transfer between electron donor and acceptor was observed directly. (authors)

  13. Radiolytic Effects on Fluoride Impurities in a U3O8 Matrix

    International Nuclear Information System (INIS)

    Icenhour, A.S.

    2000-01-01

    The safe handling and storage of radioactive materials require an understanding of the effects of radiolysis on those materials. Radiolysis may result in the production of gases (e.g., corrosives) or pressures that are deleterious to storage containers. A study has been performed to address these concerns as they relate to the radiolysis of residual fluoride compounds in uranium oxides

  14. The dependence of radiolytic H2 generation of the nitrate concentration in high-level solutions

    Energy Technology Data Exchange (ETDEWEB)

    Walker, D.D.; Bibler, N.E.

    1991-11-19

    The rate at which hydrogen is produced from the radiolysis of high-activity waste solutions depends on the radiation dose rate to the solution and the concentration of nitrate ion in solution. At a constant dose rate, the hydrogen generation rate decreases as the nitrate ion concentration increases. Using previously measured rates of hydrogen production, an equation has been derived which calculates the hydrogen generation rate when the nitrate ion concentration is known. The hydrogen generation rate from this equation can be used to more accurately predict hydrogen production in waste tanks than is currently obtained assuming a fixed generation rate. The current fixed rate underestimates the hydrogen produced in dilute waste solutions.

  15. Radiolytic degradation of diclofenac and 2,6-dichloroaniline in aqueous in solution

    International Nuclear Information System (INIS)

    Homlok, R.; Takacs, E.; Wojnarovits, L.

    2011-01-01

    Complete text of publication follows. The pharmaceutical companies in designing new molecules pay attention to the environmental toxicity of the drug; from the different variants they try to choose the less toxic one. However, metabolites, degradation products may also be toxic for the fauna and flora. For instance, diclofenac (DCF), a non steroid type anti inflammatory drug, is a moderately toxic compound. During its degradation 2,6-dichloroaniline (DCA) forms which is much more toxic than the initial molecule. In this work the radiation induced degradation of DCF and DCA is reported. The purpose of the work is the elimination of these compounds from water. The intermediates are studied using pulse radiolysis, while the degradation is followed by UV-VIS spectroscopy, separation by HPLC and products identification by diode array and MS-MS detection. The effect of dose, irradiation atmosphere, and additives are investigated. The change in chemical oxygen demand, in total organic carbon content and in toxicity of the solutions are also followed as a function of dose. The · OH radicals at both molecules add to the ring and this reaction initiates the degradation. In the case of DCF hydroxylated molecules, DCA, and quinone type compound form. In the presence of oxygen there is an increase in the hydroxylated product yield. Ring opening and mineralization is suggested to proceed through peroxy intermediates. In the case of DCA the hydroxy radical reaction is accompanied by chlorine atom elimination.

  16. Studies on the radiation chemistry of biomolecules in aqueous solution with specific objective of minimizing their radiolytic degradation. Coordinated programme for Asia and the Pacific Region on radiation sterilization practices significant to local medical supplies and conditions

    International Nuclear Information System (INIS)

    Narayana Rao, K.

    1979-01-01

    As part of a study of radiolytic degradation of pharmaceuticals during radiosterilization, the basic radiation chemistry of the B-group vitamins, nicotinamide, pyridoxin, riboflavin and thiamine, and the reaction of hydrogen peroxide with these same materials has been investigated. The various aspects studied were - radiolysis under controlled conditions, effects of phase, temperature, pH and nature and concentration of additives. Some of the conclusions are: 1) with oxygen saturated aqueous solutions containing glucose, the radiolytic degradation of the vitamins is reduced: 2) results a similar for N 2 O saturated aqueous solutions; 3) in glucose-containing solutions, the protective effect is considerably modified at higher temperatures; and 4) irradiation of air-saturated aqueous solutions in the frozen state leads to reduced decomposition. It is concluded that in the presence of oxygen, in frozen matrices at low temperature, it appears possible to reduce the radiolytic breakdown of vitamins to low levels

  17. Contribution to the study of solvated electrons in water and alcohols and of radiolytic processes in organic carbonates by picosecond pulse radiolysis

    International Nuclear Information System (INIS)

    Torche, Faycal

    2012-01-01

    This work is part of the study area of the interaction of radiation with polar liquids. Using the picosecond electron accelerator ELYSE, studies were conducted using the techniques of pulse radiolysis combined with absorption spectrophotometry Time-resolved in the field of a picosecond. This work is divided into two separate chapters. The first study addresses the temporal variation of the radiolytic yield of solvated electron in water and simple alcohols. Due to original detection system mounted on the accelerator ELYSE, composed of a flash lamp specifically designed for the detection and a streak-camera used for the first time in absorption spectroscopy, it was possible to record the time-dependent radiolytic yields of the solvated electron from ten picoseconds to a few hundred nanoseconds. The scavenging of the electron solvated by methyl viologen, was utilized to reevaluate the molar extinction coefficient of the absorption spectrum of solvated electron in water and ethanol from isobestic points which corresponds to the intersection of the absorption spectra of solvated electron which disappears and methyl viologen which is formed during the reaction. The second chapter is devoted to the study of liquid organic carbonates such as dimethyl carbonate (DMC), diethyl carbonate (DEC) and propylene carbonate (PC). This family of carbonate which compose the electrolytes lithium batteries, has never been investigated by pulse radiolysis. The studies were focused on the PC in the light of these physicochemical characteristics, including its very high dielectric constant and its strong dipole moment of 4.9 D. The first results were obtained on aqueous solutions containing propylene carbonate to observe the reactions of reduction and oxidation of PC by radiolytic species of water (solvated electron and OH radicals). Then, after the identification (spectral and kinetic) of the species formed by interaction with the OH radical as the PC* radical resulting from the

  18. Stable convergence and stable limit theorems

    CERN Document Server

    Häusler, Erich

    2015-01-01

    The authors present a concise but complete exposition of the mathematical theory of stable convergence and give various applications in different areas of probability theory and mathematical statistics to illustrate the usefulness of this concept. Stable convergence holds in many limit theorems of probability theory and statistics – such as the classical central limit theorem – which are usually formulated in terms of convergence in distribution. Originated by Alfred Rényi, the notion of stable convergence is stronger than the classical weak convergence of probability measures. A variety of methods is described which can be used to establish this stronger stable convergence in many limit theorems which were originally formulated only in terms of weak convergence. Naturally, these stronger limit theorems have new and stronger consequences which should not be missed by neglecting the notion of stable convergence. The presentation will be accessible to researchers and advanced students at the master's level...

  19. The chemiluminescence of luminol in aqueous solutions, a pulse radiolytic study

    International Nuclear Information System (INIS)

    Lind, J.

    1980-01-01

    The mechanism of chemiluminescence was studied when the luminol radical and superoxide were generated simultaneously. Hydroperoxide was formed at the first reaction step with a pKa value between 11 and 12. The dissociated form was found to undergo a monomolecular reaction leading to light generation and having a rate constant > 2 x 10 5 s -1 . The protonated form had the rate constant of approx. 2000 s -1 and formed a product which absorbed around 390 nm without light emission. The reaction of the two-electron oxidation product of luminol, 5-aminophthalazine-1, 4 dione (azaquinone), with hydrogenperoxide was stoichiometrically equivalent to the recombination of superoxide with the luminol radical. The pulseradiolytic generation of the chlorinedioxide radical ClO 2 in aqueous solution of sodium chlorite is described, and the oxidation of luminol by ClO 2 in two steps is reported: 1. Radical adducts are formed. 2. The reaction of ClO 2 x radical with the adduct to form azaquinone. The chemiluminescent reaction between the azaquinone and hydrogenperoxide consists of a second order reaction between HO 2 and the azaquinone to form a hydroperoxide followed by a monomolecular rearrangement of the dissociated form of the latter. Its acidbase equilibrium has a pKa of 10.6. A nitrogencentered structure is ascribed to the hydroperoxide formed by cross-recombination of the luminolradical and superoxide while the reaction between HO 2 and azaquinone yields a carboncentered hydroperoxide. The existence of two different emitters is evidenced by the following observations. 1. A slight difference in chemiluminescence spectra. 2. The formation of an endproduct with pKa approx. 10.2 in the luminolradical superoxide system. 3. The formation of an endproduct which acts as an efficient radial scavenger in the luminol radical superoxide system. (G.B.)

  20. Binding-site specificity of the radiolytically induced crosslinking of phenylalanine to glucagon

    International Nuclear Information System (INIS)

    Kim, H.J.; Mee, L.K.; Adelstein, S.J.; Taub, I.A.

    1984-01-01

    The γ-radiation-induced crosslinking of phenylalanine to glucagon, mediated by OH, has been shown to involve a limited number of binding sites on the glucagon molecule. Glucagon-phenylalanine adducts were partially separated from other radiolysis products with Sephadex gel filtration; further isolation of adducts was achieved with reverse-phase high-performance liquid chromatography (HLPC). Amino acid analysis of the isolated adducts indicates that the aromatic residues (phenylalanine and tyrosine), basic residues (histidine and lysine), and sulfur-containing residue (methionine) of glucagon are predominantly involved in crosslinking; these are essentially the same residues implicated in glucagon-glucagon crosslinking. Acid hydrolysates and chymotryptic digests of glucagon-phenylalanine adducts were examined with HPLC. The number of amino acid-phenylalanine adducts and also chymotryptic peptides observed was much greater than would have been expected based on the amino acid analysis. This observation is best accounted for by the involvement in crosslinking of radicals formed on the glucagon with more than one possible phenylalanine-derived free radical

  1. Thermal and combined thermal and radiolytic reactions involving nitrous oxide, hydrogen, nitrogen, and ammonia in contact with tank 241-SY-101 simulated waste

    International Nuclear Information System (INIS)

    Bryan, S.A.; Pederson, L.R.

    1996-02-01

    Work described in this report was conducted at Pacific Northwest National Laboratory (PNNL) for the Flammable Gas Safety Project, the purpose of which is to develop information needed to support Westinghouse Hanford Company (WHC) in their efforts to ensure the safe interim storage of wastes at the Hanford Site. Described in this report are the results of tests to evaluate the rates of thermal and combined thermal and radiolytic reactions involving flammable gases in the presence of Tank 241-SY-101 simulated waste. Flammable gases generated by the radiolysis of water and by the thermal and radiolytic decomposition of organic waste constituents may themselves participate in further reactions. Examples include the decomposition of nitrous oxide to yield nitrogen and oxygen, the reaction of nitrous oxide and hydrogen to produce nitrogen and water, and the reaction of nitrogen and hydrogen to produce ammonia. The composition of the gases trapped in bubbles in the wastes might therefore change continuously as a function of the time that the gas bubbles are retained

  2. The study of radiolytic stability of 25,27-bis(2-propyloxy)calix[4]-26,28-crown-6(iPr-C[4]C-6)

    International Nuclear Information System (INIS)

    Jianchen Wang; Xiaowen Zhu; Chongli Song

    2012-01-01

    The radiolytic stability of 25,27-bis(2-propyloxy)calix[4]-26,28-crown-6(iPr-C[4]C-6) was studied. The radiation source was 60 Co and its dose rate was 437 Gy/min and the total absorbed dose was from 10 4 to 10 6 Gy. The iPr-C[4]C-6 solid and 0.025 mol/L iPr-C[4]C-6/n-octanol which were pre-equilibrated with 0.01 and 3 mol/L nitric acid, respectively, were absorbed different dose and their extraction performance were researched. The degradation mechanism of them was investigated by mass spectrometry and infrared spectrum. The results show that radiolytic stability of the iPr-C[4]C-6 solid and 0.025 mol/L iPr-C[4]C-6/n-octanol are good when their absorbed dose was less than 10 6 Gy. The extracting system of iPr-C[4]C-6/n-octanol is promising for separating cesium from high level liquid waste. (author)

  3. stableGP

    Data.gov (United States)

    National Aeronautics and Space Administration — The code in the stableGP package implements Gaussian process calculations using efficient and numerically stable algorithms. Description of the algorithms is in the...

  4. CATALYTIC PROPERTY OF DOUBLE LAYERED PEROVSKITES A2MM’O6 FOR RADIOLYTICAL SPLIT OF WATER

    Directory of Open Access Journals (Sweden)

    Alexandru Cecal

    2009-06-01

    Full Text Available This paper deals with a study of water splitting by gamma rays in the presence of some double perovskites A2MM’O6 and also Sr2Fe1-xTa1+xO6. The irradiation is performed using 60Co as a source with 3·104 Ci activity and 8.3 kGy/h dose rate, which simulated the radioactive wastes, resulted from reprocessing of spent nuclear fuel elements much more active: 108-109 Ci. The stable products of radiolysis, as well as the other chemical species are measured by mass spectrometry. The calculated radiation yield (GH2 generally decreases in the order: Sr2Fe1-xTa1+xO6 (x=0.5; 0.4; 0.3; 0.1 > Ca2AlTaO6 > Sr2AlTaO6 > Ba2AlTaO6, under the given experimental conditions; the yield was higher in the presence of these catalysts than in their absence.

  5. Productivity, facies and stable-isotope records of OAE2 (Cenomanian - Turonian) in the NW European epicontinental sea: from the English Chalk to North Sea black shales

    Science.gov (United States)

    Jarvis, Ian; Olde, Kate; Trabucho-Alexandre, João; Gröcke, Darren

    2013-04-01

    The Late Cretaceous (100.5 - 66.0 Ma) provides perhaps the best example of how the Earth System may function under long-term extreme greenhouse conditions. Rapidly rising global temperatures indicate that we are heading 'back to the Cretaceous' within a few hundred years, so a better understanding of this time interval is essential. The beginning of the Late Cretaceous was characterized by a period of rapidly rising eustatic sea level, the Cenomanian transgression, which flooded continental margins and established large areas of new epicontinental sea that accumulated thick sequences of pelagic and hemipelagic carbonate (chalk). Highest global temperatures were reached during the early part of the Turonian Stage (93.9 - 89.8 Ma). This period of dramatic palaeoenvironmental change was accompanied by one the largest perturbations of the global carbon cycle in the Mesozoic: Oceanic Anoxic Event 2 (OAE2), which was characterized by a 500 kyr episode of oceanic anoxia, widespread black shale deposition, biotic turnover, and a large global positive carbon stable-isotope excursion (2 - 6 ‰ ∂13C) recorded in marine carbonates and both marine and terrestrial organic matter. The Cenomanian-Turonian boundary interval exposed at Eastbourne, southern England, has become established as a European reference section for OAE2. Here, and elsewhere in Europe, the base of the ∂13C excursion is coincident with a marked facies change from rhythmically bedded grey chalks and marls, to a >8 m thick package of dark greenish-grey marl - the Plenus Marl. The termination of OAE2 occurs 6 m above, in a package of pale-yellow-weathering nodular chalks with prominent marl seams. Sediments are organic lean (10 wt%. The onshore equivalent in eastern England (the Black Band) is similarly organic-rich, as are comparable sections in northern Germany (e.g. Wunstorf), indicating likely fully anoxic episodes within some NW European basins. The exact stratigraphic equivalence between the onshore

  6. Stable Carbon Isotope Composition (δ13C), Water Use Efficiency, and Biomass Productivity of Lycopersicon esculentum, Lycopersicon pennellii, and the F1 Hybrid

    Science.gov (United States)

    Martin, Bjorn; Thorstenson, Yvonne R.

    1988-01-01

    Three tomatoes, Lycopersicon esculentum Mill. cv UC82B, a droughttolerant wild related species, Lycopersicon pennellii (Cor.) D'Arcy, and their F1 hybrid, were grown in containers maintained at three levels of soil moisture. Season-long water use was obtained by summing over the season daily weight losses of each container corrected for soil evaporation. Plant biomass was determined by harvesting and weighing entire dried plants. Season-long water use efficiency (gram dry weight/kilogram H2O) was calculated by dividing the dry biomass by the season-long water use. The season-long water use efficiency was greatest in the wild parent, poorest in the domestic parent, and intermediate (but closer to the wild parent) in the F1 hybrid. Instantaneous water-use efficiency (micromole CO2/millimole H2O) determined by gas exchange measurements on individual leaves was poorly correlated with season-long water use efficiency. However, the relative abundance of stable carbon isotopes of leaf tissue samples was strongly correlated with the season-long water use efficiency. Also, the isotopic composition and the season-long water use efficiency of each genotype alone were strongly negatively correlated with plant dry weight when the dry weight varied as a function of soil moisture. PMID:16666269

  7. Stable carbon isotope composition (δ13C), water use efficiency, and biomass productivity of Lycopersicon esculentum, Lycopersicon pennellii, and the F1 hybrid

    International Nuclear Information System (INIS)

    Martin, B.; Thorstenson, Y.R.

    1988-01-01

    Three tomatoes, Lycopersicon esculentum Mill. cv UC82B, a droughttolerant wild related species, Lycopersicon pennellii (Cor.) D'Arcy, and their F 1 , hybrid, were grown in containers maintained at three levels of soil moisture. Season-long water use was obtained by summing over the season daily weight losses of each container corrected for soil evaporation. Plant biomass was determined by harvesting and weighing entire dried plants. Season-long water use efficiency (gram dry weight/kilogram H 2 O) was calculated by dividing the dry biomass by the season-long water use. The season-long water use efficiency was greatest in the wild parent, poorest in the domestic parent, and intermediate (but closer to the wild parent) in the F, hybrid. Instantaneous water-use efficiency (micromole CO 2 /millimole H 2 O) determined by gas exchange measurements on individual leaves was poorly correlated with season-long water use efficiency. However, the relative abundance of stable carbon isotopes of leaf tissue samples was strongly correlated with the season-long water use efficiency. Also, the isotopic composition and the season-long water use efficiency of each genotype alone were strongly negatively correlated with plant dry weight when the dry weight varied as a function of soil moisture. (author)

  8. Ultrathin MoS2-coated Ag@Si nanosphere arrays as an efficient and stable photocathode for solar-driven hydrogen production

    Science.gov (United States)

    Zhou, Qingwei; Su, Shaoqiang; Hu, Die; Lin, Lin; Yan, Zhibo; Gao, Xingsen; Zhang, Zhang; Liu, Jun-Ming

    2018-03-01

    Solar-driven photoelectrochemical (PEC) water splitting has attracted a great deal of attention recently. Silicon (Si) is an ideal light absorber for solar energy conversion. However, the poor stability and inefficient surface catalysis of Si photocathodes for the hydrogen evolution reaction (HER) have remained key challenges. Alternatively, MoS2 has been reported to exhibit excellent catalysis performance if sufficient active sites for the HER are available. Here, ultrathin MoS2 nanoflakes are directly synthesized to coat arrays of Ag-core Si-shell nanospheres (Ag@Si NSs) by using chemical vapor deposition. Due to the high surface area ratio and large curvature of these NSs, the as-grown MoS2 nanoflakes can accommodate more active sites. In addition, the high-quality coating of MoS2 nanoflakes on the Ag@Si NSs protects the photocathode from damage during the PEC reaction. An photocurrent density of 33.3 mA cm-2 at a voltage of -0.4 V is obtained versus the reversible hydrogen electrode. The as-prepared nanostructure as a hydrogen photocathode is evidenced to have high stability over 12 h PEC performance. This work opens up opportunities for composite photocathodes with high activity and stability using cheap and stable co-catalysts.

  9. Pulse radiolytic study of the oxidation reaction of uric acid in presence of bovine serum albumin: evidence of possible complex formation in the transient state

    International Nuclear Information System (INIS)

    Adhikari, S.; Gopinathan, C.

    1996-01-01

    The pulse radiolytic and spectrophotometric study of uric acid in presence of bovine serum albumin (BSA) has been carried out. In the spectrophotometric study there is no evidence for ground state interaction between BSA and uric acid. The reaction of CCl 3 OO . radical with uric acid produces a transient having absorption maximum at 330 nm and that with BSA produces transient having absorption maximum at 410 nm. In a composition of equal concentration of uric acid and BSA the CCl 3 OO . radical produces a transient absorption spectrum which shows two peaks at 330 nm and 350 nm and a shoulder at 410 nm. The peak at 350 nm is ascribed due to weak complex formation between BSA and uric acid radicals. The rate constant of CCl 3 OO . radical with uric acid increases with the increase in BSA concentration which is explained as protection of BSA by uric acid from radical attack. (author). 4 refs., 2 figs., 1 tab

  10. Thermally induced solid-state transformation of cimetidine. A multi-spectroscopic/chemometrics determination of the kinetics of the process and structural elucidation of one of the products as a stable N{sub 3}-enamino tautomer

    Energy Technology Data Exchange (ETDEWEB)

    Calvo, Natalia L.; Simonetti, Sebastian O.; Maggio, Rubén M.; Kaufman, Teodoro S., E-mail: kaufman@iquir-conicet.gov.ar

    2015-05-22

    Highlights: • Thermally stressed cimetidine above its melting point affords a stable N{sub 3} tautomer. • Multi-spectroscopic/chemometric approach developed to monitor tautomerization. • First combined use of NMR, UV and IR spectroscopies with chemometrics. • Solid cimetidine suffers first order degradation upon submission to dry heat. • Theoretical chemistry analysis confirmed the relative stability of cimetidine tautomer. - Abstract: Exposure of cimetidine (CIM) to dry heat (160–180 °C) afforded, upon cooling, a glassy solid containing new and hitherto unknown products. The kinetics of this process was studied by a second order chemometrics-assisted multi-spectroscopic approach. Proton and carbon-13 nuclear magnetic resonance (NMR), as well as ultraviolet and infrared spectroscopic data were jointly used, whereas multivariate curve resolution with alternating least squares (MCR-ALS) was employed as the chemometrics method to extract process information. It was established that drug degradation follows a first order kinetics. One of the products was structurally characterized by mono- and bi-dimensional NMR experiments. It was found to be the N{sub 3}-enamino tautomer (TAU) of CIM, resulting from the thermal isomerization of the double bond of the cyanoguanidine moiety of the drug, from the imine form to its N{sub 3}-enamine state. The thus generated tautomer demonstrated to be stable for months in the glassy solid and in methanolic solutions. A theoretical study of CIM and TAU revealed that the latter is less stable; however, the energy barrier for tautomer interconversion is high enough, precluding the process to proceed rapidly at room temperature.

  11. Development of a Safety Management Web Tool for Horse Stables.

    Science.gov (United States)

    Leppälä, Jarkko; Kolstrup, Christina Lunner; Pinzke, Stefan; Rautiainen, Risto; Saastamoinen, Markku; Särkijärvi, Susanna

    2015-11-12

    Managing a horse stable involves risks, which can have serious consequences for the stable, employees, clients, visitors and horses. Existing industrial or farm production risk management tools are not directly applicable to horse stables and they need to be adapted for use by managers of different types of stables. As a part of the InnoEquine project, an innovative web tool, InnoHorse, was developed to support horse stable managers in business, safety, pasture and manure management. A literature review, empirical horse stable case studies, expert panel workshops and stakeholder interviews were carried out to support the design. The InnoHorse web tool includes a safety section containing a horse stable safety map, stable safety checklists, and examples of good practices in stable safety, horse handling and rescue planning. This new horse stable safety management tool can also help in organizing work processes in horse stables in general.

  12. Stable Boundary Layer Issues

    NARCIS (Netherlands)

    Steeneveld, G.J.

    2012-01-01

    Understanding and prediction of the stable atmospheric boundary layer is a challenging task. Many physical processes are relevant in the stable boundary layer, i.e. turbulence, radiation, land surface coupling, orographic turbulent and gravity wave drag, and land surface heterogeneity. The

  13. Evolutionary Stable Strategy

    Indian Academy of Sciences (India)

    IAS Admin

    After Maynard-Smith and Price [1] mathematically derived why a given behaviour or strategy was adopted by a certain proportion of the population at a given time, it was shown that a strategy which is currently stable in a population need not be stable in evolutionary time (across generations). Additionally it was sug-.

  14. Determination of mycotoxins in milk-based products and infant formula using stable isotope dilution assay and liquid chromatography tandem mass spectrometry.

    Science.gov (United States)

    Zhang, Kai; Wong, Jon W; Hayward, Douglas G; Vaclavikova, Marta; Liao, Chia-Ding; Trucksess, Mary W

    2013-07-03

    A stable isotope dilution assay and liquid chromatography tandem mass spectrometry (LC-MS/MS) method was developed and validated for the determination of 12 mycotoxins, aflatoxins B₁, B₂, G₁, G₂, and M₁, deoxynivalenol, fumonisins B₁, B₂, and B₃, ochratoxin A, T-2 toxin, and zearalenone, in milk-based infant formula and foods. Samples were fortified with 12 ¹³C uniformly labeled mycotoxins ([¹³C]-mycotoxins) that correspond to the 12 target mycotoxins and prepared by dilution and filtration, followed by LC-MS/MS analysis. Quantitation was achieved using the relative response factors of [¹³C]-mycotoxins and target mycotoxins. The average recoveries in fortified milk, milk-based infant formula, milk powder, and baby yogurt of aflatoxins B₁, B₂, G₁, and G₂ (2, 10, and 50 μg/kg), aflatoxin M₁ (0.5, 2.5, and 12.5 μg/kg), deoxynivalenol, fumonisins B₁, B₂, and B₃ (40, 200, and 1000 μg/kg), ochratoxin A, T-2 toxin, and zearalenone (20, 100, and 500 μg/kg), range from 89 to 126% with RSDs of milk-based infant formula) to 136% (T-2 toxin, 20 μg/kg, milk powder), with RSDs ranging from 2 to 25%. The limits of quantitation (LOQs) were from 0.01 μg/kg (aflatoxin M₁) to 2 (fumonisin B₁) μg/kg. Aflatoxin M₁ was detected in two European Reference materials at 0.127 ± 0.013 μg/kg (certified value = 0.111 ± 0.018 μg/kg) and 0.46 ± 0.04 μg/kg (certified value = 0.44 ± 0.06 μg/kg), respectively. In 60 local market samples, aflatoxins B₁ (1.14 ± 0.10 μg/kg) and B₂ (0.20 ± 0.03 μg/kg) were detected in one milk powder sample. Aflatoxin M₁ was detected in three imported samples (condensed milk, milk-based infant formula, and table cream), ranging from 0.10 to 0.40 μg/kg. The validated method provides sufficient selectivity, sensitivity, accuracy, and reproducibility to screen for aflatoxin M₁ at nanograms per kilogram concentrations and other mycotoxins, without using standard addition or matrix-matched calibration

  15. A pilot study of a non-invasive oral nitrate stable isotopic method suggests that arginine and citrulline supplementation increases whole-body NO production in Tanzanian children with sickle cell disease.

    Science.gov (United States)

    Marealle, Alphonce I; Siervo, Mario; Wassel, Sara; Bluck, Les; Prentice, Andrew M; Minzi, Omary; Sasi, Philip; Kamuhabwa, Appolinary; Soka, Deogratias; Makani, Julie; Cox, Sharon E

    2018-04-01

    Low bioavailability of nitric oxide (NO) is implicated in the pathophysiology of sickle cell disease (SCD). We designed a nested pilot study to be conducted within a clinical trial testing the effects of a daily ready-to-use supplementary food (RUSF) fortified with arginine (Arg) and citrulline (Citr) vs. non-fortified RUSF in children with SCD. The pilot study evaluated 1) the feasibility of a non-invasive stable isotope method to measure whole-body NO production and 2) whether Arg+Citr supplementation was associated with increased whole-body NO production. Twenty-nine children (70% male, 9-11years, weight 16.3-31.3 kg) with SCD. Sixteen children received RUSF+Arg/Citr (Arg, 0.2  g/kg/day; Citr, 0.1  g/kg/day) in combination with daily chloroquine (50 mg) and thirteen received the base RUSF in combination with weekly chloroquine (150 mg). Plasma amino acids were assessed using ion-exchange elution (Biochrom-30, Biochrom, UK) and whole-body NO production was measured using a non-invasive stable isotopic method. The RUSF+Arg/Citr intervention increased plasma arginine (P = .02) and ornithine (P = .003) and decreased the ratio of asymmetric dimethylarginine to arginine (P = .01), compared to the base RUSF. A significant increase in whole-body NO production was observed in the RUSF-Arg/Citr group compared to baseline (weight-adjusted systemic NO synthesis 3.38 ± 2.29 μmol/kg/hr vs 2.35 ± 1.13 μmol/kg/hr, P = .04). No significant changes were detected in the base RUSF group (weight-adjusted systemic NO synthesis 2.64 ± 1.14 μmol/kg/hr vs 2.53 ± 1.12 μmol/kg/hr, P = .80). The non-invasive stable isotopic method was acceptable and the results provided supporting evidence that Arg/Citr supplementation may increase systemic NO synthesis in children with SCD. Copyright © 2018 The Authors. Published by Elsevier Inc. All rights reserved.

  16. Production and characterization of an acido-thermophilic, organic solvent stable cellulase from Bacillus sonorensis HSC7 by conversion of lignocellulosic wastes

    Directory of Open Access Journals (Sweden)

    Fatemeh Azadian

    2017-06-01

    Full Text Available The acidophilic and thermophilic cellulase would facilitate the conversion of lignocellulosic biomass to biofuel. In this study, Bacillus sonorensis HSC7 isolated as the best thermophilic cellulose degrading bacterium from Gorooh hot spring. 16S rRNA gene sequencing showed that, this strain closely related to the B. sonorensis. CMCase production was considered under varying environmental parameters. Results showed that, sucrose and (NH42SO4 were obtained as the best carbon and nitrogen sources for CMCase production. B. sonorensis HSC7 produced CMCase during the growth in optimized medium supplemented with agricultural wastes as sole carbon sources. The enzyme was active with optimum temperature of 70 °C and the optimum CMCase activity and stability observed at pH 4.0 and 5.0, respectively. These are characteristics indicating that, this enzyme could be an acidophilic and thermophilic CMCase. Furthermore, the CMCase activity improved by methanol (166%, chloroform (152%, while it was inhibited by DMF (61%. The CMCase activity was enhanced in the presence of Mg+2 (110%, Cu+2 (116%, Triton X-100 (118% and it retained 57% of its activity at 30% NaCl. The compatibility of HSC7 CMCase varied for each laundry detergent, with higher stability being observed in the presence of Taj® and darya®. This enzyme, that is able to work under extreme conditions, has potential applications in various industries.

  17. Scale-Up of Agrobacterium rhizogenes-Mediated Hairy Root Cultures of Rauwolfia serpentina: A Persuasive Approach for Stable Reserpine Production.

    Science.gov (United States)

    Mehrotra, Shakti; Srivastava, Vikas; Goel, Manoj K; Kukreja, Arun K

    2016-01-01

    Roots of Rauwolfia serpentina, also known as "Sarpagandha" possess high pharmaceutical value due to the presence of reserpine and other medicinally important terpene indole alkaloids. Ever increasing commercial demand of R. serpentina roots is the major reason behind the unsystematic harvesting and fast decline of the species from its natural environment. Considering Agrobacterium rhizogenes-mediated hairy root cultures as an alternative source for the production of plant-based secondary metabolites, the present optimized protocol offers a commercially feasible method for the production of reserpine, the most potent alkaloid from R. serpentina roots. This end-to-end protocol presents the establishment of hairy root culture from the leaf explants of R. serpentina through the infection of A. rhizogenes strain A4 in liquid B5 culture medium and its up-scaling in a 5 L bench top, mechanically agitated bioreactor. The transformed nature of roots was confirmed through PCR-based rol A gene amplification in genomic DNA of putative hairy roots. The extraction and quantification of reserpine in bioreactor grown roots has been done using monolithic reverse phase high-performance liquid chromatography (HPLC).

  18. The Characterisation of an Alkali-Stable Maltogenic Amylase from Bacillus lehensis G1 and Improved Malto-Oligosaccharide Production by Hydrolysis Suppression

    Science.gov (United States)

    Abdul Manas, Nor Hasmaliana; Pachelles, Samson; Mahadi, Nor Muhammad; Illias, Rosli Md.

    2014-01-01

    A maltogenic amylase (MAG1) from alkaliphilic Bacillus lehensis G1 was cloned, expressed in Escherichia coli, purified and characterised for its hydrolysis and transglycosylation properties. The enzyme exhibited high stability at pH values from 7.0 to 10.0. The hydrolysis of β-cyclodextrin (β-CD) produced malto-oligosaccharides of various lengths. In addition to hydrolysis, MAG1 also demonstrated transglycosylation activity for the synthesis of longer malto-oligosaccharides. The thermodynamic equilibrium of the multiple reactions was shifted towards synthesis when the reaction conditions were optimised and the water activity was suppressed, which resulted in a yield of 38% transglycosylation products consisting of malto-oligosaccharides of various lengths. Thin layer chromatography and high-performance liquid chromatography analyses revealed the presence of malto-oligosaccharides with a higher degree of polymerisation than maltoheptaose, which has never been reported for other maltogenic amylases. The addition of organic solvents into the reaction further suppressed the water activity. The increase in the transglycosylation-to-hydrolysis ratio from 1.29 to 2.15 and the increased specificity toward maltopentaose production demonstrated the enhanced synthetic property of the enzyme. The high transglycosylation activity of maltogenic amylase offers a great advantage for synthesising malto-oligosaccharides and rare carbohydrates. PMID:25221964

  19. Normal modified stable processes

    DEFF Research Database (Denmark)

    Barndorff-Nielsen, Ole Eiler; Shephard, N.

    2002-01-01

    This paper discusses two classes of distributions, and stochastic processes derived from them: modified stable (MS) laws and normal modified stable (NMS) laws. This extends corresponding results for the generalised inverse Gaussian (GIG) and generalised hyperbolic (GH) or normal generalised inverse...... Gaussian (NGIG) laws. The wider framework thus established provides, in particular, for added flexibility in the modelling of the dynamics of financial time series, of importance especially as regards OU based stochastic volatility models for equities. In the special case of the tempered stable OU process...

  20. Applications of stable isotopes

    International Nuclear Information System (INIS)

    Letolle, R.; Mariotti, A.; Bariac, T.

    1991-06-01

    This report reviews the historical background and the properties of stable isotopes, the methods used for their measurement (mass spectrometry and others), the present technics for isotope enrichment and separation, and at last the various present and foreseeable application (in nuclear energy, physical and chemical research, materials industry and research; tracing in industrial, medical and agronomical tests; the use of natural isotope variations for environmental studies, agronomy, natural resources appraising: water, minerals, energy). Some new possibilities in the use of stable isotope are offered. A last chapter gives the present state and forecast development of stable isotope uses in France and Europe

  1. Investigation of production method, geographical origin and species authentication in commercially relevant shrimps using stable isotope ratio and/or multi-element analyses combined with chemometrics: an exploratory analysis.

    Science.gov (United States)

    Ortea, Ignacio; Gallardo, José M

    2015-03-01

    Three factors defining the traceability of a food product are production method (wild or farmed), geographical origin and biological species, which have to be checked and guaranteed, not only in order to avoid mislabelling and commercial fraud, but also to address food safety issues and to comply with legal regulations. The aim of this study was to determine whether these three factors could be differentiated in shrimps using stable isotope ratio analysis of carbon and nitrogen and/or multi-element composition. Different multivariate statistics methods were applied to different data subsets in order to evaluate their performance in terms of classification or predictive ability. Although the success rates varied depending on the dataset used, the combination of both techniques allowed the correct classification of 100% of the samples according to their actual origin and method of production, and 93.5% according to biological species. Even though further studies including a larger number of samples in each group are needed in order to validate these findings, we can conclude that these methodologies should be considered for studies regarding seafood product authenticity. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. Simultaneous determination of heat stable peptides for eight animal and plant species in meat products using UPLC-MS/MS method.

    Science.gov (United States)

    Li, Yingying; Zhang, Yingying; Li, Huichen; Zhao, Wentao; Guo, Wenping; Wang, Shouwei

    2018-04-15

    Food adulteration and fraud is driven by economic interests; it is thus necessary to establish a high-through method that allows quantitative identification of familiar animal and plant proteins for global use. In this study, a sensitive mass spectrometric approach for the detection of eight species, including pork, beef, lamb, chicken, duck, soy, peanut, and pea, is presented and the heat stability and specificity of screened peptides are verified. To improve screening efficiency of specific peptides, several key data searching parameters, including peptides, sequence lengths, sequence coverage, and unique peptides, are investigated. Using this approach, it is possible to detect a 0.5% contamination of any of the eight species. The method is proven to have high sensitivity, specificity, repeatability, and a low quantitative detection limit with respect to adulteration of diverse types of meat products. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. Analysing Stable Time Series

    National Research Council Canada - National Science Library

    Adler, Robert

    1997-01-01

    We describe how to take a stable, ARMA, time series through the various stages of model identification, parameter estimation, and diagnostic checking, and accompany the discussion with a goodly number...

  4. Production of methoxynitrones and stable nitroxyl radicals with gem-dimethoxy groups attached to the. cap alpha. -carbon atom by the oxidation of aldonitrones in methanol

    Energy Technology Data Exchange (ETDEWEB)

    Shchukin, G.I.; Starichenko, V.F.; Grigor' ev, I.A.; Dikanov, S.A.; Gulin, V.I.; Volodarskii, L.B.

    1987-07-20

    Cyclic and acyclic aldonitrones (AN) are oxidized by a variety of reagents to hydroxamic acids and their derivatives, or more extensively with cleavage of the C-N bond. For example, Pb(OAc)/sub 4/ and MnO/sub 2/ in benzene oxidize 1-pyrroline 1-oxides to 1-acetoxy-2-pyrrolidones and 1-hydroxy-2-pyrrolidones, respectively, and oxidation with aqueous solutions of NaIO/sub 4/, KMnO/sub 4/, or NaOBr give the further oxidation products 1-hydroxy-2-pyrrolidones. On the other hand, cyclic AN give spin adducts with short-lived free radicals, and are used extensively as spin traps. The spin trap of the cyclic AN type most commonly used is 5,5-dimethyl-1-pyrroline 1-oxide (DMPO). Short-lived free radicals are frequently generated by redox reactions, commonly using Pb(OAc)/sub 4/ as the oxidant. The resulting spin adducts are converted by oxidants to substituted nitrones, but this reaction is complicated by the oxidation of the AN to hydroxamic acids or their derivatives. The aim of this investigation was to examine the behavior of imidazoline AN in comparison with DMPO in the presence of oxidants (Pb(OAc)/sub 4/, PbO/sub 2/, and MnO/sub 2/) in benzene and methanol.

  5. Combination of sugar analysis and stable isotope ratio mass spectrometry to detect the use of artificial sugars in royal jelly production.

    Science.gov (United States)

    Wytrychowski, Marine; Daniele, Gaëlle; Casabianca, Hervé

    2012-05-01

    The effects of feeding bees artificial sugars and/or proteins on the sugar compositions and (13)C isotopic measurements of royal jellies (RJs) were evaluated. The sugars fed to the bees were two C4 sugars (cane sugar and maize hydrolysate), two C3 sugars (sugar beet, cereal starch hydrolysate), and honey. The proteins fed to them were pollen, soybean, and yeast powder proteins. To evaluate the influence of the sugar and/or protein feeding over time, samples were collected during six consecutive harvests. (13)C isotopic ratio measurements of natural RJs gave values of around -25 ‰, which were also seen for RJs obtained when the bees were fed honey or C3 sugars. However, the RJs obtained when the bees were fed cane sugar or corn hydrolysate (regardless of whether they were also fed proteins) gave values of up to -17 ‰. Sugar content analysis revealed that the composition of maltose, maltotriose, sucrose, and erlose varied significantly over time in accordance with the composition of the syrup fed to the bees. When corn and cereal starch hydrolysates were fed to the bees, the maltose and maltotriose contents of the RJs increased up to 5.0 and 1.3 %, respectively, compared to the levels seen in authentic samples (i.e., samples obtained when the bees were fed natural food: honey and pollen) that were inferior to 0.2% and not detected, respectively. The sucrose and erlose contents of natural RJs were around 0.2 %, whereas those in RJs obtained when the bees were fed cane or beet sugar were as much as 4.0 and 1.3 %, respectively. The combination of sugar analysis and (13)C isotopic ratio measurements represents a very efficient analytical methodology for detecting (from early harvests onward) the use of C4 and C3 artificial sugars in the production of RJ.

  6. Protein retention assessment of four levels of poultry by-product substitution of fishmeal in rainbow trout (Oncorhynchus mykiss diets using stable isotopes of nitrogen (δ15N as natural tracers.

    Directory of Open Access Journals (Sweden)

    Daniel Badillo

    Full Text Available This is second part from an experiment where the nitrogen retention of poultry by-product meal (PBM compared to fishmeal (FM was evaluated using traditional indices. Here a quantitative method using stable isotope ratios of nitrogen (δ(15N values as natural tracers of nitrogen incorporation into fish biomass is assessed. Juvenile rainbow trout (Oncorhynchus mykiss were fed for 80 days on isotopically distinct diets in which 0, 33, 66 and 100% of FM as main protein source was replaced by PBM. The diets were isonitrogenous, isolipidic and similar in gross energy content. Fish in all treatments reached isotopic equilibrium by the end of the experiment. Two-source isotope mixing models that incorporated the isotopic composition of FM and PBM as well as that of formulated feeds, empirically derived trophic discrimination factors and the isotopic composition of fish that had reached isotopic equilibrium to the diets were used to obtain a quantitative estimate of the retention of each source of nitrogen. Fish fed the diets with 33 and 66% replacement of FM by PBM retained poultry by-product meal roughly in proportion to its level of inclusion in the diets, whereas no differences were detected in the protein efficiency ratio. Coupled with the similar biomass gain of fishes fed the different diets, our results support the inclusion of PBM as replacement for fishmeal in aquaculture feeds. A re-feeding experiment in which all fish were fed a diet of 100% FM for 28 days indicated isotopic turnover occurred very fast, providing further support for the potential of isotopic ratios as tracers of the retention of specific protein sources into fish tissues. Stable isotope analysis is a useful tool for studies that seek to obtain quantitative estimates of the retention of different protein sources.

  7. Stable agents for imaging investigations

    International Nuclear Information System (INIS)

    Tofe, A.J.

    1976-01-01

    This invention concerns highly stable compounds useful in preparing technetium 99m based scintiscanning exploration agents. The compounds of this invention include a pertechnetate reducing agent or a solution of oxidized pertechnetate and an efficient proportion, sufficient to stabilize the compounds in the presence of oxygen and of radiolysis products, of ascorbic acid or a pharmaceutically acceptable salt or ester of this acid. The invention also concerns a perfected process for preparing a technetium based exploration agent, consisting in codissolving the ascorbic acid or a pharmaceutically acceptable salt or ester of such an acid and a pertechnetate reducing agent in a solution of oxidized pertechnetate [fr

  8. Calcium stable isotope geochemistry

    Energy Technology Data Exchange (ETDEWEB)

    Gausonne, Nikolaus [Muenster Univ. (Germany). Inst. fuer Mineralogie; Schmitt, Anne-Desiree [Strasbourg Univ. (France). LHyGeS/EOST; Heuser, Alexander [Bonn Univ. (Germany). Steinmann-Inst. fuer Geologie, Mineralogie und Palaeontologie; Wombacher, Frank [Koeln Univ. (Germany). Inst. fuer Geologie und Mineralogie; Dietzel, Martin [Technische Univ. Graz (Austria). Inst. fuer Angewandte Geowissenschaften; Tipper, Edward [Cambridge Univ. (United Kingdom). Dept. of Earth Sciences; Schiller, Martin [Copenhagen Univ. (Denmark). Natural History Museum of Denmark

    2016-08-01

    This book provides an overview of the fundamentals and reference values for Ca stable isotope research, as well as current analytical methodologies including detailed instructions for sample preparation and isotope analysis. As such, it introduces readers to the different fields of application, including low-temperature mineral precipitation and biomineralisation, Earth surface processes and global cycling, high-temperature processes and cosmochemistry, and lastly human studies and biomedical applications. The current state of the art in these major areas is discussed, and open questions and possible future directions are identified. In terms of its depth and coverage, the current work extends and complements the previous reviews of Ca stable isotope geochemistry, addressing the needs of graduate students and advanced researchers who want to familiarize themselves with Ca stable isotope research.

  9. Evolutionary Stable Strategy

    Indian Academy of Sciences (India)

    2016-08-26

    Aug 26, 2016 ... Home; Journals; Resonance – Journal of Science Education; Volume 21; Issue 9. Evolutionary Stable Strategy: Application of Nash Equilibrium in Biology. General ... Using some examples of classical games, we show how evolutionary game theory can help understand behavioural decisions of animals.

  10. The Stable Concordance Genus

    OpenAIRE

    Kearney, M. Kate

    2013-01-01

    The concordance genus of a knot is the least genus of any knot in its concordance class. Although difficult to compute, it is a useful invariant that highlights the distinction between the three-genus and four-genus. In this paper we define and discuss the stable concordance genus of a knot, which describes the behavior of the concordance genus under connected sum.

  11. Manifolds admitting stable forms

    Czech Academy of Sciences Publication Activity Database

    Le, Hong-Van; Panák, Martin; Vanžura, Jiří

    2008-01-01

    Roč. 49, č. 1 (2008), s. 101-11 ISSN 0010-2628 R&D Projects: GA ČR(CZ) GP201/05/P088 Institutional research plan: CEZ:AV0Z10190503 Keywords : stable forms * automorphism groups Subject RIV: BA - General Mathematics

  12. Stable isotope studies

    International Nuclear Information System (INIS)

    Ishida, T.

    1992-01-01

    The research has been in four general areas: (1) correlation of isotope effects with molecular forces and molecular structures, (2) correlation of zero-point energy and its isotope effects with molecular structure and molecular forces, (3) vapor pressure isotope effects, and (4) fractionation of stable isotopes. 73 refs, 38 figs, 29 tabs

  13. Interactive Stable Ray Tracing

    DEFF Research Database (Denmark)

    Dal Corso, Alessandro; Salvi, Marco; Kolb, Craig

    2017-01-01

    Interactive ray tracing applications running on commodity hardware can suffer from objectionable temporal artifacts due to a low sample count. We introduce stable ray tracing, a technique that improves temporal stability without the over-blurring and ghosting artifacts typical of temporal post-pr...

  14. The stable subgroup graph

    Directory of Open Access Journals (Sweden)

    Behnaz Tolue

    2018-07-01

    Full Text Available In this paper we introduce stable subgroup graph associated to the group $G$. It is a graph with vertex set all subgroups of $G$ and two distinct subgroups $H_1$ and $H_2$ are adjacent if $St_{G}(H_1\\cap H_2\

  15. Stable massive particles at colliders

    Energy Technology Data Exchange (ETDEWEB)

    Fairbairn, M.; /Stockholm U.; Kraan, A.C.; /Pennsylvania U.; Milstead, D.A.; /Stockholm U.; Sjostrand, T.; /Lund U.; Skands, P.; /Fermilab; Sloan, T.; /Lancaster U.

    2006-11-01

    We review the theoretical motivations and experimental status of searches for stable massive particles (SMPs) which could be sufficiently long-lived as to be directly detected at collider experiments. The discovery of such particles would address a number of important questions in modern physics including the origin and composition of dark matter in the universe and the unification of the fundamental forces. This review describes the techniques used in SMP-searches at collider experiments and the limits so far obtained on the production of SMPs which possess various colour, electric and magnetic charge quantum numbers. We also describe theoretical scenarios which predict SMPs, the phenomenology needed to model their production at colliders and interactions with matter. In addition, the interplay between collider searches and open questions in cosmology such as dark matter composition are addressed.

  16. Radiolytic Synthesis of Pt-Ru Catalysts Based on Functional Polymer-Grafted MWNT and Their Catalytic Efficiency for CO and MeOH

    Directory of Open Access Journals (Sweden)

    Dae-Soo Yang

    2011-01-01

    Full Text Available Pt-Ru catalysts based on functional polymer-grafted MWNT (Pt-Ru@FP-MWNT were prepared by radiolytic deposition of Pt-Ru nanoparticles on functional polymer-grafted multiwalled carbon nanotube (FP-MWNT. Three different types of functional polymers, poly(acrylic acid (PAAc, poly(methacrylic acid (PMAc, and poly(vinylphenyl boronic acid (PVPBAc, were grafted on the MWNT surface by radiation-induced graft polymerization (RIGP. Then, Pt-Ru nanoparticles were deposited onto the FP-MWNT supports by the reduction of metal ions using γ-irradiation to obtain Pt-Ru@FP-MWNT catalysts. The Pt-Ru@FP-MWNT catalysts were then characterized by XRD, XPS, TEM ,and elemental analysis. The catalytic efficiency of Pt-Ru@FP-MWNT catalyst was examined for CO stripping and MeOH oxidation for use in a direct methanol fuel cell (DMFC. The Pt-Ru@PVPBAc-MWNT catalyst shows enhanced activity for electro-oxidation of CO and MeOH oxidation over that of the commercial E-TEK catalyst.

  17. The application of the pore population balance method to the calculation of the radiolytic weight loss and gas transport property changes of nuclear graphites

    International Nuclear Information System (INIS)

    Johnson, P.A.V.

    1982-01-01

    A pore population balance equation, previously used to describe the physical property changes of porous carbons during thermal oxidation in carbon dioxide, has been modified to treat the radiolytic oxidation of graphite in CO 2 /CO/CH 4 gas mixtures. Good agreement has been obtained between theory and experiment for the variation in the gas transport coefficients B, K and lambda of gilsonite graphite with absorbed radiation dose. Calculations indicate that the addition of blind pores to the transport porosity, and an allowance for the opening of closed pores with burn-off, do not account for the experimental fractional weight loss curve. An excellent fit is obtained, however, if a small volume of cylindrical pores of a mean radius approximately equal to the diffusion length of oxidising species in the coolant are present in the pore size spectrum. Gilsonite graphite therefore behaves as if the pore size distribution function is trimodal, with mean radii at about 0.5μm, 2.48μm and greater than or equal to 10.57μm. (author)

  18. Radiolytic degradation of TBP-HNO3 system: gas chromatographic determination of radiation chemical yields of n-butanol and nitrobutane

    International Nuclear Information System (INIS)

    Krishnamurthy, M.V.; Sipahimalani, A.T.

    1995-01-01

    Radiolytic degradation of the TBP-HNO 3 system has been studied for the radiation dose range of 19.8 to 262 kGy by the gas chromatographic method. n-Butanol and nitrobutane formed due to irradiation have been identified and estimated in pure TBP, TBP-3M HNO 3 extract and TBP-5M HNO 3 extract. The G-values (radiation chemical yields) of n-butanol are determined to be 0.28, 0.77 and 0.47 for a pure TBP, TBP-3M HNO 3 extract and TBP-5M HNO 3 extract, respectively. The G-values of nitrobutane (1-nitrobutane) are 0.55 and 1.09 for TBP-3M HNO 3 extract and TBP-5M HNO 3 extract. It is found that G(n-butanol) is less for TBP-5M HNO 3 extract than for TBP-3M HNO 3 extract, while G(nitrobutane) is grater for TBP-5M HNO 3 extract than for TBP-3M HNO 3 extract. This is explained on the basis of the formation of TBP.HNO 3 species and the role played by nitric acid in the TBP phase. (author) 12 refs.; 2 figs

  19. Radiolytic stabilization of poly(methyl methacrylate) using commercial additives; Estabilizacao radiolitica do poli(metacrilato de metila) usando aditivos comerciais

    Energy Technology Data Exchange (ETDEWEB)

    Aquino, Katia Aparecida da Silva

    2000-04-01

    Poly(methyl methacrylate), PMMA, Acrigel, a Brazilian polymer, is used in the manufacture of medical supplies sterelizable by ionizing radiation. However, when PMMA is gamma-irradiated it undergoes main chain scissions, which promote molecular degradation causing reduction in its mechanical properties. Therefore, radiolytic of PMMA is important for it to become commercially radiosterizable. In this work some commercial additives, originally used in photo-and thermo-oxidate stabilization of polymers, were tested. Only two additives, type HALS (Hindered Amine Light Stabilizer), denoted Scavenger, showed a good protective quality. The investigation of radiation-induced main scissions was carried out by viscosimetric method. The most effective additive, added to the polymer system at 0.3 w/w%, promotes a great molecular radioprotection of 93%. That means a reduction of G-value (scissions/100 eV) from 0.611 to 0.053. In addition, the glassy transition temperature (T{sub g}) of PMMA (no additive) significantly changed by radiation does not change when PMMA (with additive) is irradiated. The spectroscopy analysis, FT-IR and NMR ({sup 1}H), showed that the radioprotector added to the system does not change the PMMA structure. (author)

  20. On the identification of complexing radiolysis products in the Purex system. (20%TBP - Dodecane - HNO3)

    International Nuclear Information System (INIS)

    Becker, R.; Baumgartner, F.; Steiglitz, L.

    1978-09-01

    The lifetime of the extraction system TBP Dodecane-aqueous HNO. In the Purex process is limited by radiolytic and hydrolytic decomposition of the extracting and diluting agent which is indicated by an increased retention of fission products, especially zirconium. In this work, the radiolytically formed complexing agents responsible for this are enriched (molecular distillation) and separated in several fractions by liquid chromatography. The chemical composition of these fractions was identified by a combination of gas chromatography and mass spectrometry, supplemented by infra-red spectroscopy. As for doubtful complexing agents, they are mainly long-chain phosphoric acid esters, and, to a lesser extent, the existence of polycarbonyl compounds is suspected. The high molecular weight components of the phosphate ester fraction could be separated by gas chromatography and identified as oligomeric phosphate esters. (author)

  1. Applications of stable isotopes in clinical pharmacology

    Science.gov (United States)

    Schellekens, Reinout C A; Stellaard, Frans; Woerdenbag, Herman J; Frijlink, Henderik W; Kosterink, Jos G W

    2011-01-01

    This review aims to present an overview of the application of stable isotope technology in clinical pharmacology. Three main categories of stable isotope technology can be distinguished in clinical pharmacology. Firstly, it is applied in the assessment of drug pharmacology to determine the pharmacokinetic profile or mode of action of a drug substance. Secondly, stable isotopes may be used for the assessment of drug products or drug delivery systems by determination of parameters such as the bioavailability or the release profile. Thirdly, patients may be assessed in relation to patient-specific drug treatment; this concept is often called personalized medicine. In this article, the application of stable isotope technology in the aforementioned three areas is reviewed, with emphasis on developments over the past 25 years. The applications are illustrated with examples from clinical studies in humans. PMID:21801197

  2. Stable isotope analysis

    International Nuclear Information System (INIS)

    Tibari, Elghali; Taous, Fouad; Marah, Hamid

    2014-01-01

    This report presents results related to stable isotopes analysis carried out at the CNESTEN DASTE in Rabat (Morocco), on behalf of Senegal. These analyzes cover 127 samples. These results demonstrate that Oxygen-18 and Deuterium in water analysis were performed by infrared Laser spectroscopy using a LGR / DLT-100 with Autosampler. Also, the results are expressed in δ values (‰) relative to V-SMOW to ± 0.3 ‰ for oxygen-18 and ± 1 ‰ for deuterium.

  3. Apple Pollination Biology for Stable and Novel Fruit Production: Search System for Apple Cultivar Combination Showing Incompatibility, Semicompatibility, and Full-Compatibility Based on the S-RNase Allele Database

    Directory of Open Access Journals (Sweden)

    Shogo Matsumoto

    2014-01-01

    Full Text Available Breeding and cultivation of new apple cultivars are among the most attractive and important issues for apple researchers. As almost all apple cultivars exhibit gametophytic self-incompatibility (GSI, cross-pollination between genetically different cultivars and species is essential not only for stable fruit production, but also for breeding of new cultivars. For cross-pollination by insect or hand pollination, pollen viability and pistil fertility are key factors, but also the mechanism of GSI has to be taken into account. This paper reviews the germination rate of pollen after storage in different conditions, at different periods of flowering, and in combination with pistil fertility and cross-compatibility among wild-, crab-, and cultivated apples. Furthermore, suitable cultivar combinations for new attractive apple cultivars based on GSI are explored. Especially, details about S-genotypes of apple cultivars, which are present in recent cultivar catalogues, are introduced together with a newly established on-line searchable database of S-genotypes of cultivars, wild apples and crab apples that shows incompatibility, semicompatibility, and full-compatibility.

  4. Alkaline cation complexing with calixarenes in electro-spray / mass spectrometry. Specificity for cesium, influence of solvation on ion species and radiolytic stability of the complexing media

    International Nuclear Information System (INIS)

    Allain, Francoise

    2000-01-01

    Radioactive waste management is a rather difficult issue. In order to reduce the volume of waste storage, particularly the Cs 135 (radioactive half-life 2.3 10 6 years), liquid-liquid extraction experiments have shown that crown calixarenes were able to selectively extract cesium cation in wastes. However, the stability under radiolysis of this type of macrocycle is unknown and is the theme of this thesis. Through the coupling of electro-spray and mass spectrometry, the selectivity of crown calixarenes for cesium has been confirmed. The necessity to optimize operating conditions during the utilization of this ionization mode was acknowledged for a correct interpretation of mass spectrum. The solvent nature, source temperature, applied voltage on the cone, gaseous phase stability and species ionization desorption rate are indeed parameters that should be taken into account. Experiments show that the solution species stability is inverse to the one in gaseous phase. In a solution, species stability is linked to the nature of the solvent (solvating power) whereas in gaseous phase, it is linked to the cationic affinity. In the current radiolysis conditions it has been demonstrated that calixarenes have a stable structure. Degradation products are very largely substitution products and do not hinder the caesium cation complexing. Concerning the quantitative aspect, an estimation was produced, however results are not satisfying: reference product synthesis is in fact necessary in order to establish calibration curves that will allow to precisely dose the various components derived from radiolysis [fr

  5. Periodicity of the stable isotopes

    CERN Document Server

    Boeyens, J C A

    2003-01-01

    It is demonstrated that all stable (non-radioactive) isotopes are formally interrelated as the products of systematically adding alpha particles to four elementary units. The region of stability against radioactive decay is shown to obey a general trend based on number theory and contains the periodic law of the elements as a special case. This general law restricts the number of what may be considered as natural elements to 100 and is based on a proton:neutron ratio that matches the golden ratio, characteristic of biological and crystal growth structures. Different forms of the periodic table inferred at other proton:neutron ratios indicate that the electronic configuration of atoms is variable and may be a function of environmental pressure. Cosmic consequences of this postulate are examined. (author)

  6. Unconditionally stable perfectly matched layer boundary conditions

    NARCIS (Netherlands)

    De Raedt, H.; Michielsen, K.

    2007-01-01

    A brief review is given of a systematic, product-formula based approach to construct unconditionally stable algorithms for solving the time-dependent Maxwell equations. The fundamental difficulties that arise when we want to incorporate uniaxial perfectly matched layer boundary conditions into this

  7. Radiolytic stabilization of poly(methyl methacrylate) in blends with polystyrene; Estabilizacao radiolitica do poli(metacrilato de metila) em misturas fisicas com poliestireno

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Ivania Soares de

    2002-04-01

    In this work the radiolytic stabilization of poly(methyl methacrylate) was analyzed by three radioprotective agents: polystyrene (PS) and hindered amine light stabilizers (HEALS), respectively, PMMA/PS systems, so a called polymeric blends were prepared with different compositions, where the miscibility of these blends were studied using viscometric, microscopy (SEM) and spectroscopy (FT-IR) techniques. The results show that PMMA/PS blends in the compositions below 10 wt% of PS are miscible, on films casting from solution of toluene and methyl-ethyl-ketone (1;1) mixture. On the other hand, in the composition above 10 wt% of PS, PMMA/PS blends show imminiscibility behavior. These polymer solutions were irradiated with gamma rays ({sup 60} Co) and viscometric, microscopic and spectroscopic experiments show gamma radiation-induced compatibilization on PMMA/PS blends on proportion 50/50 and 30/70 take place. Viscometric interaction parameters of miscible and compatibilized PMMA/PS bends were calculated in the range of - 50 kGy, with the goal to find out the polymeric interactions after irradiation of the films. G values of PMMA, PMMA/PS and PMMA+St systems were calculated in order to analyze the radioprotection of PS and St into PMMA matrix. The results show that (90/10) PMMA/PS and PMMA+1,5%St systems promote protection against the gamma the radiation-induced scissions, effect that leads to polymer degradation. Moreover, a small amount of crosslinking observed in irradiated blends has contributed to stabilize mechanical properties of PMMA films. PMMA+0,3% HALS system irradiated in doses above 60 kGy showed little stabilization of the mechanical properties of PMMA, since it was observed mechanical degradation this system. Based on these results, PS and St showed to be the best radioprotective agents to PMMA. (author)

  8. Flammable gas production in Land 2 and Land 3/4 radioactive waste repositories

    International Nuclear Information System (INIS)

    1988-02-01

    Geological, radiolytic and microbiological sources of gas are considered in relation to Land 2 and Land 3/4 type radioactive waste repositories. Geological sources are potentially the most troublesome and it is concluded that site investigation work should be designed to detect gas trap structures, reservoir lithologies or source rocks. Known source and reservoir lithologies should not be considered as suitable for the siting of waste repositories. Radiolytic and microbiological sources will depend on waste characteristics. A detailed review of the literature on radiolytic gas generation is presented and conclusions from this work indicate that water in waste and matrix should be kept to a minimum. Similarly, the level of radioactivity stored in each waste container should be kept to the minimum compatible with the storage design. Microbiological gas sources will be reduced by maintaining the cellulose content of the waste at a minimum. It is suggested that the removal of organics from the waste stream would be beneficial in terms of potential gas production. (author)

  9. Marginally Stable Nuclear Burning

    Science.gov (United States)

    Strohmayer, Tod E.; Altamirano, D.

    2012-01-01

    Thermonuclear X-ray bursts result from unstable nuclear burning of the material accreted on neutron stars in some low mass X-ray binaries (LMXBs). Theory predicts that close to the boundary of stability oscillatory burning can occur. This marginally stable regime has so far been identified in only a small number of sources. We present Rossi X-ray Timing Explorer (RXTE) observations of the bursting, high- inclination LMXB 4U 1323-619 that reveal for the first time in this source the signature of marginally stable burning. The source was observed during two successive RXTE orbits for approximately 5 ksec beginning at 10:14:01 UTC on March 28, 2011. Significant mHz quasi- periodic oscillations (QPO) at a frequency of 8.1 mHz are detected for approximately 1600 s from the beginning of the observation until the occurrence of a thermonuclear X-ray burst at 10:42:22 UTC. The mHz oscillations are not detected following the X-ray burst. The average fractional rms amplitude of the mHz QPOs is 6.4% (3 - 20 keV), and the amplitude increases to about 8% below 10 keV.This phenomenology is strikingly similar to that seen in the LMXB 4U 1636-53. Indeed, the frequency of the mHz QPOs in 4U 1323-619 prior to the X-ray burst is very similar to the transition frequency between mHz QPO and bursts found in 4U 1636-53 by Altamirano et al. (2008). These results strongly suggest that the observed QPOs in 4U 1323-619 are, like those in 4U 1636-53, due to marginally stable nuclear burning. We also explore the dependence of the energy spectrum on the oscillation phase, and we place the present observations within the context of the spectral evolution of the accretion-powered flux from the source.

  10. Proliferating effect of radiolytically depolymerized carrageenan on physiological attributes, plant water relation parameters, essential oil production and active constituents of Cymbopogon flexuosus Steud. under drought stress.

    Directory of Open Access Journals (Sweden)

    Minu Singh

    Full Text Available Carrageenan has been proved as potent growth promoting substance in its depolymerized form. However, relatively little is known about its role in counteracting the adverse effects of drought stress on plants. In a pot experiment, lemongrass (Cymbopogon flexuosus Steud., grown under different water stress regimes [(100% field capacity (FC, 80% FC and 60% FC], was sprayed with 40, 80 and 120 mg L-1 of gamma irradiated carrageenan (ICA. Foliar application of ICA mitigated the harmful effects of drought stress to various extents and improved the biochemical characteristics, quality attributes and active constituents (citral and geraniol of lemongrass significantly. Among the applied treatments, ICA-80 mg L-1 proved the best in alleviating detrimental effects of drought. However, drought stress (80 and 60% FC, irrespective of the growth stages, had an adverse impact on most of the studied attributes. Generally, 60% FC proved more deleterious than 80% FC. At 80% FC, application of ICA-80 mg L-1 elevated the essential oil (EO content by 18.9 and 25%, citral content by 7.33 and 8.19% and geraniol content by 9.2 and 8.9% at 90 and 120 days after planting (DAP, respectively, as compared to the deionized-water (DW spray treatment (80% FC+ DW. Whereas, at 60% FC, foliar application of 80 mg L-1 ICA significantly augmented the EO content by 15.4 and 17.8% and active constituents viz. citral and geraniol, by 5.01 and 5.62% and by 6.06 and 5.61% at 90 and 120 DAP, respectively, as compared to the control (water-spray treatment.

  11. Assessment of gamma radiolytic degradation in waste lubricating oil by GC/MS and UV/VIS

    Science.gov (United States)

    Scapin, Marcos A.; Duarte, Celina L.; Bustillos, José Oscar W. V.; Sato, Ivone M.

    2009-07-01

    The hydrocarbons degradation by gamma irradiation of the waste automotive lubricating oil at different absorbed doses has was investigated. The waste automotive oil in a Brazilian oil recycling company was collected. This sample was fractioned and 50% and 70% (v/v) Milli-Q water were added. Each sample was irradiated with 100, 200 and 500 kGy doses using a gamma source Co-60—GAMMACELL type, with 5×10 3 Ci total activity. Gas chromatography-mass spectrometry (GC/MS) was used to identify degraded organic compounds. The mass spectra were analyzed using the mass spectral library from NIST, installed in the spectrometer. The sample irradiated at 500 kGy dose with 70% (v/v) Milli-Q water addition formed eight degradation products, namely diethanolmethylamine (C 5H 13NO), diethyldiethylene glycol (C 8H 18O 3), 1-octyn-3-ol, 4-ethyl (C 10H 18O) and 1.4-pentanediamine, N1, N1-diethyl (C 9H 22N 2). The color changing of the waste lubricating oil, for different absorbed doses, was determined by UV/VIS spectrophotometer. The related sample showed the lowest absorbance value evidencing the formation of 2-ethoxyethyl ether (C 8H 18O 3) compound.

  12. Structural, optical, opto-thermal and thermal properties of ZnS-PVA nanofluids synthesized through a radiolytic approach.

    Science.gov (United States)

    Kharazmi, Alireza; Faraji, Nastaran; Mat Hussin, Roslina; Saion, Elias; Yunus, W Mahmood Mat; Behzad, Kasra

    2015-01-01

    This work describes a fast, clean and low-cost approach to synthesize ZnS-PVA nanofluids consisting of ZnS nanoparticles homogeneously distributed in a PVA solution. The ZnS nanoparticles were formed by the electrostatic force between zinc and sulfur ions induced by gamma irradiation at a dose range from 10 to 50 kGy. Several experimental characterizations were conducted to investigate the physical and chemical properties of the samples. Fourier transform infrared spectroscopy (FTIR) was used to determine the chemical structure and bonding conditions of the final products, transmission electron microscopy (TEM) for determining the shape morphology and average particle size, powder X-ray diffraction (XRD) for confirming the formation and crystalline structure of ZnS nanoparticles, UV-visible spectroscopy for measuring the electronic absorption characteristics, transient hot wire (THW) and photoacoustic measurements for measuring the thermal conductivity and thermal effusivity of the samples, from which, for the first time, the values of specific heat and thermal diffusivity of the samples were then calculated.

  13. Structural, optical, opto-thermal and thermal properties of ZnS–PVA nanofluids synthesized through a radiolytic approach

    Science.gov (United States)

    Faraji, Nastaran; Mat Hussin, Roslina; Saion, Elias; Yunus, W Mahmood Mat; Behzad, Kasra

    2015-01-01

    Summary This work describes a fast, clean and low-cost approach to synthesize ZnS–PVA nanofluids consisting of ZnS nanoparticles homogeneously distributed in a PVA solution. The ZnS nanoparticles were formed by the electrostatic force between zinc and sulfur ions induced by gamma irradiation at a dose range from 10 to 50 kGy. Several experimental characterizations were conducted to investigate the physical and chemical properties of the samples. Fourier transform infrared spectroscopy (FTIR) was used to determine the chemical structure and bonding conditions of the final products, transmission electron microscopy (TEM) for determining the shape morphology and average particle size, powder X-ray diffraction (XRD) for confirming the formation and crystalline structure of ZnS nanoparticles, UV–visible spectroscopy for measuring the electronic absorption characteristics, transient hot wire (THW) and photoacoustic measurements for measuring the thermal conductivity and thermal effusivity of the samples, from which, for the first time, the values of specific heat and thermal diffusivity of the samples were then calculated. PMID:25821695

  14. Structural, optical, opto-thermal and thermal properties of ZnS–PVA nanofluids synthesized through a radiolytic approach

    Directory of Open Access Journals (Sweden)

    Alireza Kharazmi

    2015-02-01

    Full Text Available This work describes a fast, clean and low-cost approach to synthesize ZnS–PVA nanofluids consisting of ZnS nanoparticles homogeneously distributed in a PVA solution. The ZnS nanoparticles were formed by the electrostatic force between zinc and sulfur ions induced by gamma irradiation at a dose range from 10 to 50 kGy. Several experimental characterizations were conducted to investigate the physical and chemical properties of the samples. Fourier transform infrared spectroscopy (FTIR was used to determine the chemical structure and bonding conditions of the final products, transmission electron microscopy (TEM for determining the shape morphology and average particle size, powder X-ray diffraction (XRD for confirming the formation and crystalline structure of ZnS nanoparticles, UV–visible spectroscopy for measuring the electronic absorption characteristics, transient hot wire (THW and photoacoustic measurements for measuring the thermal conductivity and thermal effusivity of the samples, from which, for the first time, the values of specific heat and thermal diffusivity of the samples were then calculated.

  15. Gaining Control over Radiolytic Synthesis of Uniform Sub-3-nanometer Palladium Nanoparticles: Use of Aromatic Liquids in the Electron Microscope.

    Science.gov (United States)

    Abellan, Patricia; Parent, Lucas R; Al Hasan, Naila; Park, Chiwoo; Arslan, Ilke; Karim, Ayman M; Evans, James E; Browning, Nigel D

    2016-02-16

    Synthesizing nanomaterials of uniform shape and size is of critical importance to access and manipulate the novel structure-property relationships arising at the nanoscale, such as catalytic activity. In this work, we synthesize Pd nanoparticles with well-controlled size in the sub-3 nm range using scanning transmission electron microscopy (STEM) in combination with an in situ liquid stage. We use an aromatic hydrocarbon (toluene) as a solvent that is very resistant to high-energy electron irradiation, which creates a net reducing environment without the need for additives to scavenge oxidizing radicals. The primary reducing species is molecular hydrogen, which is a widely used reductant in the synthesis of supported metal catalysts. We propose a mechanism of particle formation based on the effect of tri-n-octylphosphine (TOP) on size stabilization, relatively low production of radicals, and autocatalytic reduction of Pd(II) compounds. We combine in situ STEM results with insights from in situ small-angle X-ray scattering (SAXS) from alcohol-based synthesis, having similar reduction potential, in a customized microfluidic device as well as ex situ bulk experiments. This has allowed us to develop a fundamental growth model for the synthesis of size-stabilized Pd nanoparticles and demonstrate the utility of correlating different in situ and ex situ characterization techniques to understand, and ultimately control, metal nanostructure synthesis.

  16. Radiolytically depolymerized sodium alginate improves physiological activities, yield attributes and composition of essential oil of Eucalyptus citriodora Hook.

    Science.gov (United States)

    Ali, Akbar; Khan, M Masroor A; Uddin, Moin; Naeem, M; Idrees, Mohd; Hashmi, Nadeem; Dar, Tariq Ahmad; Varshney, Lalit

    2014-11-04

    Eucalyptus citriodora Hook. is highly valued for its citronellal-rich essential oil (EO) extracted from its leaves. Hence, escalated EO production of eucalyptus is the need of hour. Marine polysaccharides (sodium alginate) are processed through gamma radiation of particular intensity, to obtain the irradiated sodium alginate (ISA). A pot experiment was conducted to study the effect of foliar application of ISA on growth, biochemical, physiological, EO yield and composition of E. citriodora. The treatments were applied as: foliar spray of deionized water only (control), seed soaked with ISA (90 mg L(-1)) and foliar spray of ISA with 30, 60, 120 and 240 mg L(-1). The treatment 6 (spray of ISA at 120 mg L(-1)) showed the highest value for most of the parameters studied. It also enhanced the EO content (33.3%), EO yield (86.7%), citronellal content (63.4%) and citronellal yield (205.5%) as compared to the control. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Giant-Planet Chemistry: Ammonium Hydrosulfide (NH4SH), Its IR Spectra and Thermal and Radiolytic Stabilities

    Science.gov (United States)

    Loeffler, Mark J.; Hudson, Reggie L.; Chanover, Nancy J.; Simon, Amy A.

    2015-01-01

    Here we present our recent studies of proton-irradiated and unirradiated ammonium hydrosulfide, NH4SH, a compound predicted to be an important tropospheric cloud component of Jupiter and other giant planets. We irradiated both crystalline and amorphous NH4SH at 10-160 K and used IR spectroscopy to observe and identify reaction products in the ice, specifically NH3 and long-chained sulfur-containing ions. Crystalline NH4SH was amorphized during irradiation at all temperatures studied with the rate being the fastest at the lowest temperatures. Irradiation of amorphous NH4SH at approximately 10-75 K showed that 60-80% of the NH4 + remained when equilibrium was reached, and that NH4SH destruction rates were relatively constant within this temperature range. Irradiations at higher temperatures produced different dose dependence and were accompanied by pressure outbursts that, in some cases, fractured the ice. The thermal stability of irradiated NH4SH was found to be greater than that of unirradiated NH4SH, suggesting that an irradiated giant-planet cloud precipitate can exist at temperatures and altitudes not previously considered.

  18. Stable isotope analysis of dynamic lipidomics.

    Science.gov (United States)

    Brandsma, Joost; Bailey, Andrew P; Koster, Grielof; Gould, Alex P; Postle, Anthony D

    2017-08-01

    Metabolic pathway flux is a fundamental element of biological activity, which can be quantified using a variety of mass spectrometric techniques to monitor incorporation of stable isotope-labelled substrates into metabolic products. This article contrasts developments in electrospray ionisation mass spectrometry (ESI-MS) for the measurement of lipid metabolism with more established gas chromatography mass spectrometry and isotope ratio mass spectrometry methodologies. ESI-MS combined with diagnostic tandem MS/MS scans permits the sensitive and specific analysis of stable isotope-labelled substrates into intact lipid molecular species without the requirement for lipid hydrolysis and derivatisation. Such dynamic lipidomic methodologies using non-toxic stable isotopes can be readily applied to quantify lipid metabolic fluxes in clinical and metabolic studies in vivo. However, a significant current limitation is the absence of appropriate software to generate kinetic models of substrate incorporation into multiple products in the time domain. Finally, we discuss the future potential of stable isotope-mass spectrometry imaging to quantify the location as well as the extent of lipid synthesis. This article is part of a Special Issue entitled: BBALIP_Lipidomics Opinion Articles edited by Sepp Kohlwein. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Dynamical attraction to stable processes

    OpenAIRE

    Fisher, Albert M.; Talet, Marina

    2012-01-01

    We apply dynamical ideas within probability theory, proving an almost-sure invariance principle in log density for stable processes. The familiar scaling property (self-similarity) of the stable process has a stronger expression, that the scaling flow on Skorokhod path space is a Bernoulli flow. We prove that typical paths of a random walk with i.i.d. increments in the domain of attraction of a stable law can be paired with paths of a stable process so that, after applying a non-random regula...

  20. Hydrolytically stable titanium-45

    DEFF Research Database (Denmark)

    Severin, Gregory; Fonslet, Jesper; Zhuravlev, Fedor

    2014-01-01

    . The high cross-section and production rates on an unenriched metal foil target contribute to make 45Ti an ideal PET radionuclide. In order to bring 45Ti to even a preclinical plat-form, the hydrolytic instability of aqueous Ti(IV) needs to be addressed. Recently, the groups of Edit Tshuva (Hebrew...... to ion-pairing, and eluted with isopropanol. iv. 45Ti was extracted onto a polystyrene based 1,3 diol resin (RAPP polymers) and labeling commenced on the column. Radiolabeling was slightly different in each condition, but in general the salan and dipic ligands were added to the 45Ti in pyridine...

  1. Productivity

    DEFF Research Database (Denmark)

    Spring, Martin; Johnes, Geraint; Hald, Kim Sundtoft

    Productivity is increasingly critical for developed economies. It has always been important: as Paul Krugman puts it, “Productivity isn’t everything, but in the long run it is almost everything. A country’s ability to improve its standard of living over time depends almost entirely on its ability...... to raise its output per worker”(Krugman, 1994). Analyses of productivity have, by and large, been the preserve of economists. Operations Management (OM) is rooted in a similar concern for the efficient use of scarce resources; Management Accounting (MA) is concerned with the institutionalised measurement...... and management of productivity. Yet the three perspectives are rarely connected. This paper is a sketch of a literature review seeking to identify, contrast and reconcile these three perspectives. In so doing, it aims to strengthen the connections between policy and managerial analyses of productivity....

  2. Advanced thermally stable jet fuels

    Energy Technology Data Exchange (ETDEWEB)

    Schobert, H.H.

    1999-01-31

    The Pennsylvania State University program in advanced thermally stable coal-based jet fuels has five broad objectives: (1) Development of mechanisms of degradation and solids formation; (2) Quantitative measurement of growth of sub-micrometer and micrometer-sized particles suspended in fuels during thermal stressing; (3) Characterization of carbonaceous deposits by various instrumental and microscopic methods; (4) Elucidation of the role of additives in retarding the formation of carbonaceous solids; (5) Assessment of the potential of production of high yields of cycloalkanes by direct liquefaction of coal. Future high-Mach aircraft will place severe thermal demands on jet fuels, requiring the development of novel, hybrid fuel mixtures capable of withstanding temperatures in the range of 400--500 C. In the new aircraft, jet fuel will serve as both an energy source and a heat sink for cooling the airframe, engine, and system components. The ultimate development of such advanced fuels requires a thorough understanding of the thermal decomposition behavior of jet fuels under supercritical conditions. Considering that jet fuels consist of hundreds of compounds, this task must begin with a study of the thermal degradation behavior of select model compounds under supercritical conditions. The research performed by The Pennsylvania State University was focused on five major tasks that reflect the objectives stated above: Task 1: Investigation of the Quantitative Degradation of Fuels; Task 2: Investigation of Incipient Deposition; Task 3: Characterization of Solid Gums, Sediments, and Carbonaceous Deposits; Task 4: Coal-Based Fuel Stabilization Studies; and Task 5: Exploratory Studies on the Direct Conversion of Coal to High Quality Jet Fuels. The major findings of each of these tasks are presented in this executive summary. A description of the sub-tasks performed under each of these tasks and the findings of those studies are provided in the remainder of this volume

  3. Stable isotope separation

    International Nuclear Information System (INIS)

    Botter, F.; Molinari, Ph.; Dirian, G.

    1964-01-01

    circulates. Studies are going forward to increase the separation factor of the cascade by using an auxiliary gas. Isotopic Exchange: A series of experiments has been performed to determine the isotopic separation factor between a lithium amalgam and an organic solvent containing a lithium salt. The various parameters which may enter into this exchange were studied: the influence of the type of solvent (the two solvents used were dimethylformamide and tetrahydrofurane), of the temperature, of the concentration and of the nature of the associated halogen. Solutions of Li metal and liquid NH 3 were studied also. A number of tests were carried out to see whether there was a difference between the isotopic compositions of the Li present in the two liquid layers obtained by the dissolution of Li metal in ammonia. No difference was observed between the Li isotopic ratios in the two phases. This was also true in the case of a layer of of Li in liquid NH 3 and a layer of Li I in a similar solvent. Electromigration: The method of counter current electro Migration in fused salts is a powerful isotopic enrichment technique. It can be used successfully to separate the isotopes of elements with strongly metallic character. In the case of alkalis, small quantities of isotopically pure 7 Li have been obtained, while the enrichment factors obtained for potassium are of the order of 10. With regard to the alkaline earths, it has been possible to produce small quantities of calcium enriched 5 times in 46 Ca. However considerable technological difficulties rise up in the way of production on a semi-industrial scale. (authors) [fr

  4. Shelf-Stable Food Safety

    Science.gov (United States)

    ... is an MRE? Is an MRE shelf stable? What foods are packaged in retort packages? What is aseptic ... type of package is used for aseptic processing? What foods are packaged in aseptic packages? Can I microwave ...

  5. Pharmaceuticals labelled with stable isotopes

    International Nuclear Information System (INIS)

    Krumbiegel, P.

    1986-11-01

    The relatively new field of pharmaceuticals labelled with stable isotopes is reviewed. Scientific, juridical, and ethical questions are discussed concerning the application of these pharmaceuticals in human medicine. 13 C, 15 N, and 2 H are the stable isotopes mainly utilized in metabolic function tests. Methodical contributions are given to the application of 2 H, 13 C, and 15 N pharmaceuticals showing new aspects and different states of development in the field under discussion. (author)

  6. Stable isotope research pool inventory

    International Nuclear Information System (INIS)

    1984-03-01

    This report contains a listing of electromagnetically separated stable isotopes which are available at the Oak Ridge National Laboratory for distribution for nondestructive research use on a loan basis. This inventory includes all samples of stable isotopes in the Research Materials Collection and does not designate whether a sample is out on loan or is in reprocessing. For some of the high abundance naturally occurring isotopes, larger amounts can be made available; for example, Ca-40 and Fe-56

  7. production

    African Journals Online (AJOL)

    answered satisfactorily. An additional important factor in discouraging collaborative work in animal and grassland production is, without doubt, the complexity of work in this field compared with much of that in the individual discipline and, in particular, the com- plexity of work on forage as a source of nutrients for live- stock.

  8. Stable Boundary Layer Education (STABLE) Final Campaign Summary

    Energy Technology Data Exchange (ETDEWEB)

    Turner, David D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2016-03-01

    The properties of, and the processes that occur in, the nocturnal stable boundary layer are not well understood, making it difficult to represent adequately in numerical models. The nocturnal boundary layer often is characterized by a temperature inversion and, in the Southern Great Plains region, a low-level jet. To advance our understanding of the nocturnal stable boundary layer, high temporal and vertical resolution data on the temperature and wind properties are needed, along with both large-eddy simulation and cloud-resolving modeling.

  9. Reaction of H atoms with chelators in highly basic solution: H2 production in high level liquid waste simulants

    International Nuclear Information System (INIS)

    Barnabas, F.; Cerny, E.; Jonah, C.D.; Meisel, D.; Sauer, M.C. Jr.

    1995-01-01

    The rate constants for hydrogen abstraction by H from ethylene-diamine tetracetic acid (EDTA), N-(2-hydroxyethyl)-ethylenediaminetriacetic acid (HEDTA), nitrilotriacetic acid (NTA), iminodiacetic acid (IDA), glycolic acid and citric acid were measured at pH 13. The predominant product of these reactions is H 2 . The rate constants obtained are more than an order of magnitude larger than the literature rates that had been measured at pH 1. These measurements are of significance for understanding the radiolytic production of H 2 in nuclear waste storage tanks. (Author)

  10. Use of stable isotopes in human nutrition in Senegal

    International Nuclear Information System (INIS)

    2016-01-01

    In Senegal, the Laboratory of Nutrition of the Department of Animal Biology of the Faculty of Science and Technology of UCAD has been using stable isotopic techniques for nearly twenty years. Stable isotopes were applied to different target populations to measure milk production, exclusive breastfeeding, body composition, micronutrient bioavailability and total energy expenditure.The application of stable isotopic techniques in nutrition has contributed to advocacy for exclusive breastfeeding for up to 6 months in Senegal. It enabled government decision-makers to obtain essential information on the quality of foods needed for optimal effect during pregnancy and for infant growth and the results were reflected in the national policy on micronutrient supplementation.

  11. What can Fe stable isotopes tell us about magmas?

    DEFF Research Database (Denmark)

    Stausberg, Niklas

    The majority of the Earth’s crust is formed by magmas, and understanding their production and differentiation is important to interpret the geologic rock record. A powerful tool to investigate magmatic processes is the distribution of the stable isotopes of the major redox-sensitive element...... the differentiation of magmas from the perspective of Fe stable isotopes, integrated with petrology, by studying igneous rocks and their constituent phases (minerals and glasses) from the Bushveld Complex, South Africa, Thingmuli, Iceland, Pantelleria, Italy, and the Bishop Tuff, USA. The findings are interpreted...... and for more quantitative model of the magmatic processes producing enigmatic stable isotope compositions of rhyolitic and granite magmas....

  12. Considerations in the design of a high power medical isotope production reactor

    International Nuclear Information System (INIS)

    Ball, Russell M.; Nordyke, William H.; Brown, Roy

    2002-01-01

    For the low enriched aqueous homogeneous reactor to be economic in the production of medical isotopes, such as Mo-99 and Sr-89, the power level should be of the order of 100 kWth. This is double the earlier designs and this paper discusses the design changes which must be considered to meet this goal. The topics considered are: 1. Heat removal from the reactor solution; 2. Recombination of radiolytic gases; 3. Adequate radiation shielding; 4. Stability of reactor power with fluctuating reactivity; 5. Adequate cooling of the reflector; 6. Independent shutdown mechanisms; 7. Required volume of the reactor; 8. Economic implementation. (author)

  13. Assay of brines for common radiolysis products

    International Nuclear Information System (INIS)

    MacDougall, C.S.

    1981-01-01

    Brines are assayed for four common products of radiolytic reaction. Free chlorine is determined spectrophotometrically after reaction with o-tolidine. The test is specific for chlorine, and quantities of chlorine from 0.1 to 6 μg in the test aliquot are determined with a precision of about +- 5%. Hydrogen peroxide is reacted with xylenol orange and determined spectrophotometrically with a precision of +- 5% on 2-μg quantities of peroxide. A spectrophotometric method using thiocyanate is employed in the chlorate assay. After subtracting the bias caused by any H 2 O 2 or Cl 2 , 1-μg quantities of chlorate can be determined with a precision of +- 10%. Perchlorate ion quantities of 1 ppM can be determined directly in brines by ion chromatography with a precision of about +- 15%

  14. Volatile profile, lipid oxidation and protein oxidation of irradiated ready-to-eat cured turkey meat products

    International Nuclear Information System (INIS)

    Feng, Xi; Ahn, Dong Uk

    2016-01-01

    Irradiation had little effects on the thiobarbituric acid reactive substances (TBARS) values in ready-to-eat (RTE) turkey meat products, while it increased protein oxidation at 4.5 kGy. The volatile profile analyses indicated that the amount of sulfur compounds increased linearly as doses increased in RTE turkey meat products. By correlation analysis, a positive correlation was found between benzene/ benzene derivatives and alcohols with lipid oxidation, while aldehydes, ketones and alkane, alkenes and alkynes were positively correlated with protein oxidation. Principle component analysis showed that irradiated meat samples can be discriminated by two categories of volatile compounds: Strecker degradation products and radiolytic degradation products. The cluster analysis of volatile data demonstrated that low-dose irradiation had minor effects on the volatile profile of turkey sausages (<1.5 kGy). However, as the doses increased, the differences between the irradiated and non-irradiated cured turkey products became significant. - Highlights: • Irradiation had little effects on lipid oxidation of ready-to-eat cured turkey. • 4.5 kGy irradiation increased protein oxidation. • Irradiated samples were isolated due to Strecker/radiolytic degradation products. • 1.5 kGy irradiation had limited effects on the volatile profile of turkey sausages. • Dimethyl disulfide can be used as a potential marker for irradiated meat products.

  15. Radiation-stable polyolefin compositions

    International Nuclear Information System (INIS)

    Rekers, J.W.

    1986-01-01

    This invention relates to compositions of olefinic polymers suitable for high energy radiation treatment. In particular, the invention relates to olefinic polymer compositions that are stable to sterilizing dosages of high energy radiation such as a gamma radiation. Stabilizers are described that include benzhydrol and benzhydrol derivatives; these stabilizers may be used alone or in combination with secondary antioxidants or synergists

  16. Monitoring of stable glaucoma patients

    NARCIS (Netherlands)

    K.M. Holtzer-Goor (Kim); N.S. Klazinga (Niek); M.A. Koopmanschap (Marc); H.G. Lemij (Hans); T. Plochg; E. van Sprundel (Esther)

    2010-01-01

    textabstractA high workload for ophthalmologists and long waiting lists for patients challenge the organization of ophthalmic care. Tasks that require less specialized skills, like the monitoring of stable (well controlled) glaucoma patients could be substituted from ophthalmologists to other

  17. Purification and biochemical characterization of a 22-kDa stable cysteine- like protease from the excretory-secretory product of the liver fluke Fasciola hepatica by using conventional techniques.

    Science.gov (United States)

    Hemici, Ahmed; Benerbaiha, Roumaila Sabrina; Bendjeddou, Dalila

    2017-11-15

    This study describes the purification and characterization of a stable protease activity isolated from Fasciola hepatica adult worms maintained in vitro by employing acetone precipitation (40-60%) followed by a gel filtration through Sephadex G-100 and DEAE- cellulose ion exchange column. Through this three-step purification, the enzyme was purified 11-fold with a specific activity of 1893.9U/mg and 31.5% recovery. After the final ultrafiltration step, the purification fold was increased up to 13.1 and the overall activity yield reached a rate of 18.8%. The MW of the purified protease was estimated by reducing SDS-PAGE to be 22kDa while the proteolytic activity detection was carried out by zymography on non-denaturing SDS-PAGE containing the casein as substrate. Using this substrate, the protease showed extreme proteolytic activity at pH 5.5 and temperature 35-40°C and was highly stable over a wide range of pH, from 5.0 to 10.0. In addition to its preference for the Z-Phe-Arg-AMC fluorogenic substrate resulting in maximum proteolytic activity (99.7%) at pH 7.0, the pure protease exhibited highest cleavage activity against hemoglobin and casein substrates at pH 5.5 (85.6% and 82.8%, respectively). The K m values obtained for this protease were 5.4, 13, 160 and approximately 1000μM using respectively the fluorogenic substrate Z-Phe-Arg-AMC, hemoglobin, casein and albumin. The protease activity was completely inhibited either by E-64 inhibitor (5mM) or iodoacetamide (10mM), indicating its cysteine nature. The usefulness of the purified protease as an antigen was studied by immunoblotting. Thus, sera from sheep experimentally infected with F. hepatica recognized the protease band at 2 weeks post-infection (WPI) and strongly at 7 WPI. The early detection of antibodies anti- F. hepatica suggests the application of this molecule as a specific epitope for the serodiagnosis of fascioliasis disease. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Construction of energy-stable Galerkin reduced order models.

    Energy Technology Data Exchange (ETDEWEB)

    Kalashnikova, Irina; Barone, Matthew Franklin; Arunajatesan, Srinivasan; van Bloemen Waanders, Bart Gustaaf

    2013-05-01

    This report aims to unify several approaches for building stable projection-based reduced order models (ROMs). Attention is focused on linear time-invariant (LTI) systems. The model reduction procedure consists of two steps: the computation of a reduced basis, and the projection of the governing partial differential equations (PDEs) onto this reduced basis. Two kinds of reduced bases are considered: the proper orthogonal decomposition (POD) basis and the balanced truncation basis. The projection step of the model reduction can be done in two ways: via continuous projection or via discrete projection. First, an approach for building energy-stable Galerkin ROMs for linear hyperbolic or incompletely parabolic systems of PDEs using continuous projection is proposed. The idea is to apply to the set of PDEs a transformation induced by the Lyapunov function for the system, and to build the ROM in the transformed variables. The resulting ROM will be energy-stable for any choice of reduced basis. It is shown that, for many PDE systems, the desired transformation is induced by a special weighted L2 inner product, termed the %E2%80%9Csymmetry inner product%E2%80%9D. Attention is then turned to building energy-stable ROMs via discrete projection. A discrete counterpart of the continuous symmetry inner product, a weighted L2 inner product termed the %E2%80%9CLyapunov inner product%E2%80%9D, is derived. The weighting matrix that defines the Lyapunov inner product can be computed in a black-box fashion for a stable LTI system arising from the discretization of a system of PDEs in space. It is shown that a ROM constructed via discrete projection using the Lyapunov inner product will be energy-stable for any choice of reduced basis. Connections between the Lyapunov inner product and the inner product induced by the balanced truncation algorithm are made. Comparisons are also made between the symmetry inner product and the Lyapunov inner product. The performance of ROMs constructed

  19. Toward Practical Secure Stable Matching

    Directory of Open Access Journals (Sweden)

    Riazi M. Sadegh

    2017-01-01

    Full Text Available The Stable Matching (SM algorithm has been deployed in many real-world scenarios including the National Residency Matching Program (NRMP and financial applications such as matching of suppliers and consumers in capital markets. Since these applications typically involve highly sensitive information such as the underlying preference lists, their current implementations rely on trusted third parties. This paper introduces the first provably secure and scalable implementation of SM based on Yao’s garbled circuit protocol and Oblivious RAM (ORAM. Our scheme can securely compute a stable match for 8k pairs four orders of magnitude faster than the previously best known method. We achieve this by introducing a compact and efficient sub-linear size circuit. We even further decrease the computation cost by three orders of magnitude by proposing a novel technique to avoid unnecessary iterations in the SM algorithm. We evaluate our implementation for several problem sizes and plan to publish it as open-source.

  20. Towards stable acceleration in LINACS

    CERN Document Server

    Dubrovskiy, A D

    2014-01-01

    Ultra-stable and -reproducible high-energy particle beams with short bunches are needed in novel linear accelerators and, in particular, in the Compact Linear Collider CLIC. A passive beam phase stabilization system based on a bunch compression with a negative transfer matrix element R56 and acceleration at a positive off-crest phase is proposed. The motivation and expected advantages of the proposed scheme are outlined.

  1. Relative contribution of natural productivity and compound feed to tissue growth in blue shrimp (Litopenaeus stylirostris) reared in biofloc: Assessment by C and N stable isotope ratios and effect on key digestive enzymes

    OpenAIRE

    Cardona, Emilie; Lorgeoux, Benedicte; Geffroy, Claire; Richard, Pierre; Saulnier, Denis; Gueguen, Yannick; Guillou, Gael; Chim, Liet

    2015-01-01

    The aim of this study was to assess the relative contribution of natural productivity and compound food to the growth of the juvenile blue shrimp Litopenaeus stylirostris reared in a biofloc system. Two experiments were carried out based on the same protocol with three treatments: clear water with experimental diet (CW), biofloc with experimental diet (BF) and biofloc unfed (BU). Shrimp survival was significantly higher in biofloc rearing than in CW rearing. The contribution of the biofloc to...

  2. Production of thermo-alkali-stable laccase and xylanase by co-culturing of Bacillus sp. and B. halodurans for biobleaching of kraft pulp and deinking of waste paper.

    Science.gov (United States)

    Gupta, Vijaya; Garg, Shruti; Capalash, Neena; Gupta, Naveen; Sharma, Prince

    2015-05-01

    To reduce pollution and cost of treatment for fresh and recycled paper, co-production of xylanase and laccase was carried out in the same production medium using two compatible species of Bacillus. These co-produced enzymes were used for deinking of old newsprint (ONP) and biobleaching of eucalyptus Kraft pulp. Solid-state co-cultivation of Bacillus sp. and B. halodurans FNP135 was optimized statistically by response surface methodology for the co-production of xylanase (X) and laccase (L). A significant increase in production of xylanase (2.1-fold, 1,685 IU/g) and laccase (2.04-fold, 2,270 nkat/g) was observed under optimized conditions viz. pH (10.5), inoculum size (10 + 10 %) and moisture:substrate ratio (0.8:1). Both the enzymes showed identical temperature and pH optima of 70 °C and 9, respectively, and were used for deinking of ONP pulp and biobleaching of kraft pulp. In case of ONP pulp deinking, the XL treatment increased brightness (11.8 %), freeness (17.8 %), breaking length (34.8 %), burst factor (2.77 %) and tear factor (2.4 %). In case of kraft pulp biobleaching, XL treatment showed a significant increase in brightness (13 %), whiteness (106.15 %) breaking length (49 %), burst factor (6.9 %), tear factor (23 %), and viscosity (11.68 %) and reduction in kappa number (15 %) after alkali extraction and peroxide stage. This enhancement of pulp properties revealed a synergistic effect of xylanase and laccase produced in one setup.

  3. Biotechnological Potential of Agro Residues for Economical Production of Thermoalkali-Stable Pectinase by Bacillus pumilus dcsr1 by Solid-State Fermentation and Its Efficacy in the Treatment of Ramie Fibres

    Directory of Open Access Journals (Sweden)

    Deepak Chand Sharma

    2012-01-01

    Full Text Available The production of a thermostable and highly alkaline pectinase by Bacillus pumilus dcsr1 was optimized in solid-state fermentation (SSF and the impact of various treatments (chemical, enzymatic, and in combination on the quality of ramie fibres was investigated. Maximum enzyme titer (348.0±11.8 Ug−1 DBB in SSF was attained, when a mixture of agro-residues (sesame oilseed cake, wheat bran, and citrus pectin, 1 : 1 : 0.01 was moistened with mineral salt solution ( 0.92, pH 9.0 at a substrate-to-moistening agent ratio of 1 : 2.5 and inoculated with 25% of 24 h old inoculum, in 144 h at 40°C. Parametric optimization in SSF resulted in 1.7-fold enhancement in the enzyme production as compared to that recorded in unoptimized conditions. A 14.2-fold higher enzyme production was attained in SSF as compared to that in submerged fermentation (SmF. The treatment with the enzyme significantly improved tensile strength and Young’s modulus, reduction in brittleness, redness and yellowness, and increase in the strength and brightness of ramie fibres.

  4. Constraining the role of iron in environmental nitrogen transformations. Dual stable isotope systematics of abiotic NO2- reduction by Fe(II) and its production of N2O

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, David [Harvard Univ., Cambridge, MA (United States); Wankel, Scott David [Woods Hole Oceanographic Inst., MA (United States); Buchwald, Carolyn [Woods Hole Oceanographic Inst., MA (United States); Hansel, Colleen [Woods Hole Oceanographic Inst., MA (United States)

    2015-09-16

    Redox reactions involving nitrogen and iron have been shown to have important implications for mobilization of priority contaminants. Thus, an understanding of the linkages between their biogeochemical cycling is critical for predicting subsurface mobilization of radionuclides such as uranium. Despite mounting evidence for biogeochemical interactions between iron and nitrogen, our understanding of their environmental importance remains limited. Here we present an investigation of abiotic nitrite (NO2-) reduction by Fe(II) or ‘chemodenitrification,’ and its relevance to the production of nitrous oxide (N2O), specifically focusing on dual (N and O) isotope systematics under a variety of environmentally relevant conditions. We observe a range of kinetic isotope effects that are regulated by reaction rates, with faster rates at higher pH (~8), higher concentrations of Fe(II) and in the presence of mineral surfaces. A clear non-linear relationship between rate constant and kinetic isotope effects of NO2- reduction was evident (with larger isotope effects at slower rates) and is interpreted as reflecting the dynamics of Fe(II)-N reaction intermediates. N and O isotopic composition of product N2O also suggests a complex network of parallel and/or competing pathways. Our findings suggest that NO2- reduction by Fe(II) may represent an important abiotic source of environmental N2O, especially in iron-rich environments experiencing dynamic redox variations. This study provides a multi-compound, multi-isotope framework for evaluating the environmental occurrence of abiotic NO2- reduction and N2O formation, helping future studies constrain the relative roles of abiotic and biological N2O production pathways.

  5. Embedded Controller Design for Pig Stable Ventilation Systems

    DEFF Research Database (Denmark)

    Jessen, Jan Jacob

    present an early result for performing system identification for zone based climate dynamics, based on an idea of guaranteed internal flow directions. Paper 6 presents a verified stable distributed temperature controller for pig stables divided into zones. Paper 7 is an expanded journal version of paper 6......This thesis focuses on zone based climate control in pig stables and how to implement climate controllers in a new range of products. The presented controllers are based on simple models of climate dynamics and simple models of actuators. The implementation uses graphical point and click features...... from the Mathworks' range of products and automatic code generation. It is furthermore shown how to build new climate control systems based on cheap and readily available hardware and software. An early result for performing system identification for zone based climate dynamics is also presented...

  6. Production of ammonium sulfate doubly labeled with the {sup 15}N and {sup 34}S stable isotopes; Producao de sulfato de amonio duplamente marcado com os isotopos estaveis {sup 15}N e {sup 34}S

    Energy Technology Data Exchange (ETDEWEB)

    Maximo, Everaldo; Bendassolli, Jose Albertino; Trivelin, Paulo Cesar Ocheuze; Rossete, Alexssandra Luiza Rodrigues Molina; Oliveira, Claudineia Raquel de; Prestes, Clelber Vieira [Centro de Energia Nuclear na Agricultura (CENA), Piracicaba, SP (Brazil)]. E-mail: jab@cena.usp.br

    2005-04-01

    The purpose of this work was the production of ammonium sulfate double labeled with {sup 15}N and {sup 34}S ((15NH{sub 4}){sub 2}{sup 34}SO{sub 4})), employing the ion exchange technique in two different processes. The first one was carried out using Na{sub 2}{sup 34}SO{sub 4} and ({sup 15}NH{sub 4}){sub 2}SO{sub 4} previously enriched. It was possible to obtain about 54g of ({sup 15}NH{sub 4}){sub 2}{sup 34}SO{sub 4} from 70.0g of Na{sub 2}{sup 34}SO{sub 4} and 64.2g of ({sup 15}NH{sub 4}){sub 2}SO{sub 4} . The second method involved the production of H{sub 2}{sup 34}SO{sub 4}, by ion exchange, and its subsequent reaction with {sup 15}NH{sub 3(aq)}, using a distillation system, to yield 58 g of ({sup 15}NH{sub 4}){sub 2}{sup 34}SO{sub 4} from 43.1 g of H{sub 2}{sup 34}SO{sub 4}. (author)

  7. Stable Hemiaminals: 2-Aminopyrimidine Derivatives

    Directory of Open Access Journals (Sweden)

    Anna Kwiecień

    2015-08-01

    Full Text Available Stable hemiaminals can be obtained in the one-pot reaction between 2-aminopyrimidine and nitrobenzaldehyde derivatives. Ten new hemiaminals have been obtained, six of them in crystal state. The molecular stability of these intermediates results from the presence of both electron-withdrawing nitro groups as substituents on the phenyl ring and pyrimidine ring, so no further stabilisation by intramolecular interaction is required. Hemiaminal molecules possess a tetrahedral carbon atom constituting a stereogenic centre. As the result of crystallisation in centrosymmetric space groups both enantiomers are present in the crystal structure.

  8. Organic synthesis with stable isotopes

    International Nuclear Information System (INIS)

    Daub, G.H.; Kerr, V.N.; Williams, D.L.; Whaley, T.W.

    1978-01-01

    Some general considerations concerning organic synthesis with stable isotopes are presented. Illustrative examples are described and discussed. The examples include DL-2-amino-3-methyl- 13 C-butanoic-3,4- 13 C 2 acid (DL-valine- 13 C 3 ); methyl oleate-1- 13 C; thymine-2,6- 13 C 2 ; 2-aminoethanesulfonic- 13 C acid (taurine- 13 C); D-glucose-6- 13 C; DL-2-amino-3-methylpentanoic-3,4- 13 C 2 acid (DL-isoleucine- 13 C 2 ); benzidine- 15 N 2 ; and 4-ethylsulfonyl-1-naphthalene-sulfonamide- 15 N

  9. MixSIAR: advanced stable isotope mixing models in R

    Science.gov (United States)

    Background/Question/Methods The development of stable isotope mixing models has coincided with modeling products (e.g. IsoSource, MixSIR, SIAR), where methodological advances are published in parity with software packages. However, while mixing model theory has recently been ex...

  10. Stable cosmology in chameleon bigravity

    Science.gov (United States)

    De Felice, Antonio; Mukohyama, Shinji; Oliosi, Michele; Watanabe, Yota

    2018-02-01

    The recently proposed chameleonic extension of bigravity theory, by including a scalar field dependence in the graviton potential, avoids several fine-tunings found to be necessary in usual massive bigravity. In particular it ensures that the Higuchi bound is satisfied at all scales, that no Vainshtein mechanism is needed to satisfy Solar System experiments, and that the strong coupling scale is always above the scale of cosmological interest all the way up to the early Universe. This paper extends the previous work by presenting a stable example of cosmology in the chameleon bigravity model. We find a set of initial conditions and parameters such that the derived stability conditions on general flat Friedmann background are satisfied at all times. The evolution goes through radiation-dominated, matter-dominated, and de Sitter eras. We argue that the parameter space allowing for such a stable evolution may be large enough to encompass an observationally viable evolution. We also argue that our model satisfies all known constraints due to gravitational wave observations so far and thus can be considered as a unique testing ground of gravitational wave phenomenologies in bimetric theories of gravity.

  11. Stable isotope mass spectrometry in petroleum exploration

    International Nuclear Information System (INIS)

    Mathur, Manju

    1997-01-01

    The stable isotope mass spectrometry plays an important role to evaluate the stable isotopic composition of hydrocarbons. The isotopic ratios of certain elements in petroleum samples reflect certain characteristics which are useful for petroleum exploration

  12. Stable rotating dipole solitons in nonlocal media

    DEFF Research Database (Denmark)

    Lopez-Aguayo, Servando; Skupin, Stefan; Desyatnikov, Anton S.

    2006-01-01

    We present the first example of stable rotating two-soliton bound states in nonlinear optical media with nonlocal response. We show that, in contrast to media with local response, nonlocality opens possibilities to generate stable azimuthons.......We present the first example of stable rotating two-soliton bound states in nonlinear optical media with nonlocal response. We show that, in contrast to media with local response, nonlocality opens possibilities to generate stable azimuthons....

  13. Uses of stable isotopes in fish ecology

    Science.gov (United States)

    Analyses of fish tissues (other than otoliths) for stable isotope ratios can provide substantial information on fish ecology, including physiological ecology. Stable isotopes of nitrogen and carbon frequently are used to determine the mix of diet sources for consumers. Stable i...

  14. Stable States of Biological Organisms

    Science.gov (United States)

    Yukalov, V. I.; Sornette, D.; Yukalova, E. P.; Henry, J.-Y.; Cobb, J. P.

    2009-04-01

    A novel model of biological organisms is advanced, treating an organism as a self-consistent system subject to a pathogen flux. The principal novelty of the model is that it describes not some parts, but a biological organism as a whole. The organism is modeled by a five-dimensional dynamical system. The organism homeostasis is described by the evolution equations for five interacting components: healthy cells, ill cells, innate immune cells, specific immune cells, and pathogens. The stability analysis demonstrates that, in a wide domain of the parameter space, the system exhibits robust structural stability. There always exist four stable stationary solutions characterizing four qualitatively differing states of the organism: alive state, boundary state, critical state, and dead state.

  15. Theory of stable allocations II

    Directory of Open Access Journals (Sweden)

    Pantelić Svetlana

    2015-01-01

    Full Text Available The Swedish Royal Academy awarded the 2012 Nobel Prize in Economics to Lloyd Shapley and Alvin Roth, for the theory of stable allocations and the practice of market design. These two American researchers worked independently from each other, combining basic theory and empirical investigations. Through their experiments and practical design they generated a flourishing field of research and improved the performance of many markets. Shapley provided the fundamental theoretical contribution to this field of research, whereas Roth, a professor at the Harvard University in Boston, developed and upgraded these theoretical investigations by applying them to the American market of medical doctors. Namely, their research helps explain the market processes at work, for instance, when doctors are assigned to hospitals, students to schools and human organs for transplant to recipients.

  16. Exploring cancer metabolism using stable isotope-resolved metabolomics (SIRM).

    Science.gov (United States)

    Bruntz, Ronald C; Lane, Andrew N; Higashi, Richard M; Fan, Teresa W-M

    2017-07-14

    Metabolic reprogramming is a hallmark of cancer. The changes in metabolism are adaptive to permit proliferation, survival, and eventually metastasis in a harsh environment. Stable isotope-resolved metabolomics (SIRM) is an approach that uses advanced approaches of NMR and mass spectrometry to analyze the fate of individual atoms from stable isotope-enriched precursors to products to deduce metabolic pathways and networks. The approach can be applied to a wide range of biological systems, including human subjects. This review focuses on the applications of SIRM to cancer metabolism and its use in understanding drug actions. © 2017 by The American Society for Biochemistry and Molecular Biology, Inc.

  17. Stable Treemaps via Local Moves.

    Science.gov (United States)

    Sondag, Max; Speckmann, Bettina; Verbeek, Kevin

    2018-01-01

    Treemaps are a popular tool to visualize hierarchical data: items are represented by nested rectangles and the area of each rectangle corresponds to the data being visualized for this item. The visual quality of a treemap is commonly measured via the aspect ratio of the rectangles. If the data changes, then a second important quality criterion is the stability of the treemap: how much does the treemap change as the data changes. We present a novel stable treemapping algorithm that has very high visual quality. Whereas existing treemapping algorithms generally recompute the treemap every time the input changes, our algorithm changes the layout of the treemap using only local modifications. This approach not only gives us direct control over stability, but it also allows us to use a larger set of possible layouts, thus provably resulting in treemaps of higher visual quality compared to existing algorithms. We further prove that we can reach all possible treemap layouts using only our local modifications. Furthermore, we introduce a new measure for stability that better captures the relative positions of rectangles. We finally show via experiments on real-world data that our algorithm outperforms existing treemapping algorithms also in practice on either visual quality and/or stability. Our algorithm scores high on stability regardless of whether we use an existing stability measure or our new measure.

  18. Study on the plutonium extraction and reextraction in radiolytic degraded system 30 % TBP-n-dodecane/HNO3-H2O

    International Nuclear Information System (INIS)

    Hoffmann, P.M.; Wronska, T.

    1980-01-01

    The degree of the complexation of plutonium(4) by the products of radiolysis of the system 30 % TBP-n-dodecane/HNO 3 -H 2 O as a function of radiation dose and concentration of nitric acid has been studied. The special method of calculation based on extraction equilibria was used. The retention of plutonium in the organic phase after single reductive reextraction has been determined. (author)

  19. Properties of bituminization product from Olkiluoto power plant

    International Nuclear Information System (INIS)

    Valkiainen, M.; Vuorinen, U.

    1985-09-01

    In Finland, disposal into repositories excavated into bedrock on the present power plant sites is considered to be the most feasible alternative for the low- and intermediate level wastes. The Nuclear Waste Commission of the Finnish power companies has sponsored mainly experimental research work on long-term properties of bituminized ion exchange resin performed in the Reactor Laboratory of the Technical Research Centre of Finland since 1981. This report presents results on follow-up measurements of the leach tests started in 1981 and results on new leach tests with cement equilibrated water. Swelling of the bituminization product caused by water uptake is considered important. Both unrestricted and restricted swelling measurements were performed and are reported here. In addition to leaching and swelling also radiolytic gas generation and pH-changes of the leachant are discussed

  20. Production of oxidatively stable fish oil enriched food emulsions

    DEFF Research Database (Denmark)

    Bruni Let, Mette

    Purpose: The objective of the project is to determine how a number of selected fish oil enriched foods can be protected against oxidation by the right choice of antioxidants, emulsifiers and optimal process conditions. Furthermore the influence of antioxidant addition to the fish oil it......-self on the effect of antioxidants added to the foods will also be investigated. Background: Fish oils are rich sources of the long-chain polyunsaturated fatty acids EPA and DHA of which DHA is a vital component of the phospholipids of human cellular membranes, especially those in the brain and retina. Fish oils...... have many other health benefiting properties such as preventing heart diseases. Addition of fish oils to foods is therefore of interest. The many double bonds in the fatty acids are however susceptible to oxidation. Collaboration partners: The project is a collaborative project between DFU-FF, Bio...

  1. Quality Improvement Project for Shelf Stable Bakery Products

    Science.gov (United States)

    2009-07-01

    more slowly than others. PTS formed unswollen starch granules that increased firmness. Starch (Osella et al., 2005) Bread (corn starch, cassava ...1992) Amylose-lipid complex in wheat flour, starch, and isolated complex DSC, X-ray diffractometer Multiple endotherms in flour and starch but... Multiple range test analysis for toughness of cake samples stored at 37 0C and cycled to lower temperatures (4 and 25 0C) Different formulations Count LS

  2. Unit of stable isotopic N15 analysis

    International Nuclear Information System (INIS)

    Cabrera de Bisbal, Evelin; Paredes U, Maria

    1997-01-01

    The continuous and growing demand of crops and cattle for the domestic inhabitants, forces the search of technical solutions in agriculture. One of the solutions able to be covered in a near future it is the escalation of agricultural production in lands already being cultivated, either by means of an intensification of cultivation and / or increasing the unitary yields. In the intensive cropping systems, the crops extract substantial quantities of nutriments that is recovered by means of the application of fertilizers. Due to the lack of resources and to the increase of commercial inputs prices, it has been necessary to pay attention to the analysis and improvement of low inputs cropping systems and to the effective use of resources. Everything has made to establish a concept of plant nutrition focused system, which integrate the sources of nutriments for plants and the production factors of crops in a productive cropping system, to improve the fertility of soils, the agricultural productivity and profitability. This system includes the biggest efficiency of chemical fertilizers as the maximum profit of alternative sources of nutriments, such as organic fertilizers, citrate-phosphate rocks and biological nitrogen fixation. By means of field experiments under different environmental conditions (soils and climate) it can be determined the best combination of fertilizers practice (dose, placement, opportunity and source) for selected cropping systems. The experimentation with fertilizer, marked with stable and radioactive isotopes, provides a direct and express method to obtain conclusive answers to the questions: where, when and how should be applied. The fertilizers marked with N 1 5 have been used to understand the application of marked fertilizer to the cultivations, and the determination of the proportion of crops nutritious element derived from fertilizer. The isotopic techniques offer a fast and reliable mean to obtain information about the distribution of

  3. Population Games, Stable Games, and Passivity

    Directory of Open Access Journals (Sweden)

    Michael J. Fox

    2013-10-01

    Full Text Available The class of “stable games”, introduced by Hofbauer and Sandholm in 2009, has the attractive property of admitting global convergence to equilibria under many evolutionary dynamics. We show that stable games can be identified as a special case of the feedback-system-theoretic notion of a “passive” dynamical system. Motivated by this observation, we develop a notion of passivity for evolutionary dynamics that complements the definition of the class of stable games. Since interconnections of passive dynamical systems exhibit stable behavior, we can make conclusions about passive evolutionary dynamics coupled with stable games. We show how established evolutionary dynamics qualify as passive dynamical systems. Moreover, we exploit the flexibility of the definition of passive dynamical systems to analyze generalizations of stable games and evolutionary dynamics that include forecasting heuristics as well as certain games with memory.

  4. Volatile profile, lipid oxidation and protein oxidation of irradiated ready-to-eat cured turkey meat products

    Science.gov (United States)

    Feng, Xi; Ahn, Dong Uk

    2016-10-01

    Irradiation had little effects on the thiobarbituric acid reactive substances (TBARS) values in ready-to-eat (RTE) turkey meat products, while it increased protein oxidation at 4.5 kGy. The volatile profile analyses indicated that the amount of sulfur compounds increased linearly as doses increased in RTE turkey meat products. By correlation analysis, a positive correlation was found between benzene/ benzene derivatives and alcohols with lipid oxidation, while aldehydes, ketones and alkane, alkenes and alkynes were positively correlated with protein oxidation. Principle component analysis showed that irradiated meat samples can be discriminated by two categories of volatile compounds: Strecker degradation products and radiolytic degradation products. The cluster analysis of volatile data demonstrated that low-dose irradiation had minor effects on the volatile profile of turkey sausages (turkey products became significant.

  5. Influence of the diluent on the radiolytic degradation of TBP in TBP systems, 30% (V/V) - diluent-nitric acid

    International Nuclear Information System (INIS)

    Rubenich, M.N.

    1976-03-01

    The influence of the diluent on the degradation of TBP was studied by a gas chromatographic technique. The results obtained have shown that the aromatic diluents decrease markedly the HDBP production in the radiolysis of TBP, while n-dodecane, which is being used as diluent, promotes this radiolysis. However, the influence of the diluent become not too significant on the total (radiolysis + hydrolysis) solutions containing nitric acid. In view of foreseeing applications of aromatic diluents or their mixtures with aliphatic diluents on nuclear fuel reprocessing, it would be advisable to carry out more research on the system TBP/diluent, particularly on the kinetics of the hydrolysis of TBP and the influence of the diluent on the TBP degradation under conditions similar to those verified in the Purex Process [pt

  6. LHC Report: Towards stable beams and collisions

    CERN Multimedia

    CERN Bulletin

    2011-01-01

    Over the past two weeks, the LHC re-commissioning with beam has continued at a brisk pace. The first collisions of 2011 were produced on 2 March, with stable beams and collisions for physics planned for the coming days. Low intensity beams with just a few bunches of particles were used to test the energy ramp to 3.5 TeV and the squeeze. The results were successful and, as a by-product, the first collisions of 2011 were recorded 2 March. One of the main activities carried out by the operation teams has been the careful set-up of the collimation system, and the injection and beam dump protection devices. The collimation system provides essential beam cleaning, preventing stray particles from impacting other elements of the machine, particularly the superconducting magnets. In addition to the collimation system, also the injection and beam dump protection devices perform a vital machine protection role, as they detect any beam that might be mis-directed during rare, but not totally unavoidable, hardware hiccups...

  7. Highly enriched stable and actinide isotopes for scientific investigation in Russian Federal Nuclear Center Arzamas-16

    International Nuclear Information System (INIS)

    Vesnovskii, S.P.; Shulzhenko, P.F.

    1997-01-01

    The paper describes the production of highly enriched isotopes of uranium and transuranium elements by electromagnetic separation and same stable isotopes for scientific and applied research in physics and environment, for reference materials and standard sources

  8. The iron stable isotope fingerprint of the human diet.

    Science.gov (United States)

    von Blanckenburg, Friedhelm; Noordmann, Janine; Guelke-Stelling, Monika

    2013-12-11

    The stable isotopes of iron disclose the metabolic pathways of iron within the human food chain. We have measured with precise multicollector ICP-MS the iron concentrations and stable isotope composition of 60 food products that are representative of the average German diet. We find that vegetables fall within the range typical of strategy I plants (-0.1 to -1.4‰ in δ(56)Fe), crop products and processed crop foods into the range typical of strategy II plants (-0.6 to +0.4‰), and animal products into the (54)Fe-enriched range known for animal tissue and blood (-1.1 to -2.7‰). Weighting these isotope compositions by the average iron dietary sources, we find a representative composition of European vegetarian diet of -0.45‰, whereas that of omnivores is -0.82‰. For human blood, known to be enriched in light iron isotopes, we find fractionation factors for iron absorption of -2.0 and -2.3‰ for vegetarians (female and male, respectively) and -1.3 and -1.5‰ for omnivores (female and male, respectively). Knowing these fractionation factors is a prerequisite for using stable iron isotope ratios in blood as monitors of intestinal iron uptake regulation.

  9. Radiation-chemical effects in the near-field of a final disposal site: role of bromine on the radiolytic processes in NaCl-solutions

    Energy Technology Data Exchange (ETDEWEB)

    Ershov, B.G.; Gordeev, A.V. [Inst. of Physical Chemistry, Russian Academy of Sciences, Moscow (Russian Federation); Kelm, M.; Bohnert, E. [Inst. fuer Nukleare Entsorgung, Forschungszentrum Karlsruhe, Karlsruhe (Germany); Janata, E. [Hahn-Meitner-Inst., Berlin (Germany)

    2002-07-01

    The oxidation of Br{sup -} by Cl{sub 2}{sup -} is investigated by gamma pulse radiolysis in aqueous solutions of NaCl and NaBr. Depending on the ratio of the concentration of Br{sup -} to Cl{sup -}, the main product being observed is either Cl{sub 2}{sup -}, ClBr{sup -} or Br{sub 2}{sup -}. The mixed radical anion ClBr{sup -} exhibits a broad absorption band at 350 nm with {epsilon}{sub 350} = 9300 dm{sup 3} mol{sup -1} cm{sup -1}. The rate constants of the equilibrium Cl{sub 2}{sup -} + Br{sup -} <=> ClBr{sup -} + Cl{sup -} are determined to be k{sub f} = 4 x 10{sup 9} dm{sup 3} mol{sup -1} s{sup -1} and k{sub b} = 1.1 x 10{sup 2} dm{sup 3} mol{sup -1} s{sup -1}. The formation of the Cl{sub 3}{sup -} ({lambda}{sub max} = 220 nm), Cl{sub 2}Br{sup -} ({lambda}{sub max} = 230 nm) and ClBr{sub 2}{sup -} ({lambda}{sub max} = 245 nm) ions in the radiation-chemical oxidation of Cl{sup -} and Br{sup -} ions in an aqueous solution was observed by pulse radiolysis, and its mechanisms of appearance and the equilibrium constants were determined. (orig.)

  10. Gas phase thermal diffusion of stable isotopes

    International Nuclear Information System (INIS)

    Eck, C.F.

    1979-01-01

    The separation of stable isotopes at Mound Facility is reviewed from a historical perspective. The historical development of thermal diffusion from a laboratory process to a separation facility that handles all the noble gases is described. In addition, elementary thermal diffusion theory and elementary cascade theory are presented along with a brief review of the uses of stable isotopes

  11. physico-chemical and stable isotopes

    African Journals Online (AJOL)

    This paper details the mineralogical, chemical and stable isotope abundances of calcrete in the Letlhakeng fossil valley. The stable isotope abundances (O and C) of calcretes yielded some values which were tested against the nature of the calcretes – pedogenic or groundwater type. The Kgalagadi (Kalahari) is a vast ...

  12. Modelling stable atmospheric boundary layers over snow

    NARCIS (Netherlands)

    Sterk, H.A.M.

    2015-01-01

    Thesis entitled:

    Modelling Stable Atmospheric Boundary Layers over Snow

    H.A.M. Sterk

    Wageningen, 29th of April, 2015

    Summary

    The emphasis of this thesis is on the understanding and forecasting of the Stable Boundary Layer (SBL) over snow-covered surfaces. SBLs

  13. Modelling stable atmospheric boundary layers over snow

    NARCIS (Netherlands)

    Sterk, H.A.M.

    2015-01-01

    Thesis entitled: Modelling Stable Atmospheric Boundary Layers over Snow H.A.M. Sterk Wageningen, 29th of April, 2015 Summary The emphasis of this thesis is on the understanding and forecasting of the Stable Boundary Layer (SBL) over snow-covered surfaces. SBLs typically form at night and in polar

  14. Stable isotopes and biomarkers in microbial ecology

    NARCIS (Netherlands)

    Boschker, H.T.S.; Middelburg, J.J.

    2002-01-01

    The use of biomarkers in combination with stable isotope analysis is a new approach in microbial ecology and a number of papers on a variety of subjects have appeared. We will first discuss the techniques for analysing stable isotopes in biomarkers, primarily gas chromatography-combustion-isotope

  15. Stable Agrobacterium -mediated transformation of the halophytic ...

    African Journals Online (AJOL)

    Stable Agrobacterium-mediated transformation of the halophytic Leymus chinensis (Trin.) Yan-Lin Sun, Soon-Kwan Hong. Abstract. In this study, an efficient procedure for stable Agrobacterium-mediated transformation of Leymus chinensis (Trin.) was established. Agrobacterium tumefaciens strain EHA105, harboring a ...

  16. Irradiation of Oil / Water Biphasic Systems: the Importance of Interfacial Surface Area on the Production of Hydrogen and Other Deleterious Products

    International Nuclear Information System (INIS)

    Causey, Patrick-W.; Stuart, Craig-R.

    2012-09-01

    Occasionally, organic materials, such as lubricating oils, can enter irradiated aqueous reactor systems. This can upset the chemistry control of the reactor, resulting in elevated hydrogen gas concentrations, changes in system pH and the formation of unwanted degradation products. Most available information on the radiation chemistry of oil is extrapolated from irradiations of neat simple hydrocarbons like hexane; there is little information available as to the radiolytic breakdown of larger hydrocarbons in the presence of water. In the absence of water, the general radiation effects on hydrocarbons can be divided into fragmentation and polymerizations reactions. Some factors that can influence the degradation of hydrocarbons include the extent of hydrocarbon branching, the degree of bond-saturation, and the presence of scavenging molecules and dissolved gases. The mechanism of water radiolysis is well understood and tools are available to simulate such radiation chemistry. Additionally, irradiations of aqueous systems containing trace quantities of soluble organic species and ion exchange resins have also been studied. However, at least initially, oils that enter irradiated aqueous systems are essentially insoluble in water. This leads to a non-homogeneous system where radiation energy is deposited in both water and organic phases, each of which will have distinct irradiation behaviours. In addition to the irradiation effects in the aqueous and organic phases, the effects of irradiation on the chemistry at the interface between the phases and the rate of production of soluble hydrocarbon fragments from the degradation of the oil are unknown. A program was initiated to examine the radiation chemistry effects on aqueous systems contaminated with insoluble hydrocarbon-based oils. A unique vessel has been designed and fabricated for the irradiation of hydrocarbon-water mixtures in a Gammacell 60 Co γ-irradiator. The design allows for variation of the hydrocarbon

  17. Gamma radiation treatment of pentachlorophenol, 2,4-dichlorophenol and 2-chlorophenol in water

    International Nuclear Information System (INIS)

    He Yongke; Liu Jun; Wu Jilan

    2001-01-01

    The aim of this work was to investigate γ radiation treatment of pentachlorophenol (PCP), 2,4- dichlorophenol (DCP) and o-chlorophenol (o-CP) in water. The dechlorination of PCP, DCP and o-CP has been studied using γ radiation as well as ozonization. G(CI-) is always much higher than the corresponding G(-PCP),this means that some primary radiolytic products are unstable during post irradiation. PCP is much easier to be decomposed under irradiation than that of simple chlorophenol. Some stable radiolytic intermediates were be detected. Primary analysis reveals some quinones among the final products with toxicity that remains unclear. In the pulse radiolytic experiment, it was determined that about 53% of radicals undergo electrotransfer and others undergo addition when OH radicals react with PCP. The values of COD(Mn) after irradiating PCP in dosage were determined. It is recommended to bubble ozone simultaneously when radiation (or electron beam) treat CPs contaminating water. (author)

  18. Temperature and radiolytic corrosion effects on the chlorine behaviour in nuclear graphite: consequences for the disposable of irradiated graphite from UNGG reactors; Effets de la temperature et de la corrosion radiolytique sur le comportement du chlore dans le graphite nucleaire: consequences pour le stockage des graphites irradies des reacteurs UNGG

    Energy Technology Data Exchange (ETDEWEB)

    Vaudey, C.E.

    2010-10-15

    This work concerns the dismantling of the UNGG reactor which have produced around 23 000 t of graphite wastes that ave to be disposed of according to the French law of June 206. These wastes contain two long-lived radionuclides ({sup 14}C and {sup 36}Cl) which are the main long term dose contributors. In order to get information about their inventory and their long term behaviour in case of water ingress into the repository, it is necessary to determine their location and speciation in the irradiated graphite after the reactor shutdown. This work concerns the study of {sup 36}Cl. The main objective is to reproduce its behaviour during reactor operation. For that purpose, we have studied the effects of temperature and radiolytic corrosion independently. Our results show a rapid release of around 20% {sup 36}Cl during the first hours of reactor operation whereas a much slower release occurs afterwards. We have put in evidence two types of chlorine corresponding to two different chemical forms (of different thermal stabilities) or to two locations (of different accessibilities). We have also shown that the radiolytic corrosion seems to enhance chlorine release, whatever the irradiation dose. Moreover, the major chemical form of chlorine is inorganic. (author)

  19. Structure of acid-stable carmine.

    Science.gov (United States)

    Sugimoto, Naoki; Kawasaki, Yoko; Sato, Kyoko; Aoki, Hiromitsu; Ichi, Takahito; Koda, Takatoshi; Yamazaki, Takeshi; Maitani, Tamio

    2002-02-01

    Acid-stable carmine has recently been distributed in the U.S. market because of its good acid stability, but it is not permitted in Japan. We analyzed and determined the structure of the major pigment in acid-stable carmine, in order to establish an analytical method for it. Carminic acid was transformed into a different type of pigment, named acid-stable carmine, through amination when heated in ammonia solution. The features of the structure were clarified using a model compound, purpurin, in which the orientation of hydroxyl groups on the A ring of the anthraquinone skeleton is the same as that of carminic acid. By spectroscopic means and the synthesis of acid-stable carmine and purpurin derivatives, the structure of the major pigment in acid-stable carmine was established as 4-aminocarminic acid, a novel compound.

  20. Stable Fly, (L., Dispersal and Governing Factors

    Directory of Open Access Journals (Sweden)

    Allan T. Showler

    2015-01-01

    Full Text Available Although the movement of stable fly, Stomoxys calcitrans (L., has been studied, its extent and significance has been uncertain. On a local scale (13 km is mainly wind-driven by weather fronts that carry stable flies from inland farm areas for up to 225 km to beaches of northwestern Florida and Lake Superior. Stable flies can reproduce for a short time each year in washed-up sea grass, but the beaches are not conducive to establishment. Such movement is passive and does not appear to be advantageous to stable fly's survival. On a regional scale, stable flies exhibit little genetic differentiation, and on the global scale, while there might be more than one “lineage”, the species is nevertheless considered to be panmictic. Population expansion across much of the globe likely occurred from the late Pleistocene to the early Holocene in association with the spread of domesticated nomad livestock and particularly with more sedentary, penned livestock.

  1. Towards effective and stable probiotics.

    Science.gov (United States)

    Yarullina, D R; Damshkaln, L G; Bruslik, N L; Konovalova, O A; Ilinskaya, O N; Lozinsky, V I

    2015-01-01

    Probiotics are live microorganisms, generally either lactobacilli or bifidobacteria, which when administered in adequate amounts confer a health benefit to the host [1]. Due to the growing evidence of health benefits associated with their use, probiotics are of increasing interest and represent now a significant growth area in the functional foods industry [2]. However, to be effective, orally administered probiotics should survive preparation of dosage forms and passage through acidic environment of the gastrointestinal tract (GIT). Reaching the intestine, these microorganisms should be able to establish themselves, remain viable and perform their beneficial actions. In this context, oral formulations have to protect probiotic bacteria from gastric acidity and delay their release in the small intestine in order to allow their complete release in the colon. To evaluate effects of starch formulations of lactobacilli on their survival in gastric environment and probiotic properties. Nineteen Lactobacillus strains belonging to the species L. fermentum (14 strains), L. plantarum (4 strains), and L. rhamnosus (1 strain), were isolated from dairy products and probiotics, and were used in this study. Lactobacilli were cultured in de Man, Rogosa, Sharpe (MRS) broth (Merck, Germany) under microaerobic conditions at 37°C.Amylolytic activity of lactobacilli, cultured for 3-5 days on MRS agar supplemented with 1% soluble potato starch (SPS), was determined with iodine reagent (0.01 M I2-KI solution).Loading in starch was performed with L. plantarum 8PA3 bacteria ("Dry lactobacterin", Perm, Russia), which were resuspended to the concentration 1010 cells/mL in 10 mL of 0.85% NaCl solution and added to 90 mL of 2.5% SPS solution. Resulting mixture was frozen at -18°C and then lyophilized (Martin Christ Alpha 1-2 LDplus, Germany).Atomic force microscopy (AFM) images of formulated L. plantarum 8PA3 cells were acquired in air by a Solver P47H atomic force microscope (NT

  2. A review of literature relevant to gas production in radioactive waste

    International Nuclear Information System (INIS)

    Norris, G.H.

    1987-11-01

    A review of relevant recent papers on gas generation in low-level wastes and intermediate-level wastes is presented. Chemical, microbiological, radiolytic and thermal reactions are considered for both unconditioned wastes and wastes conditioned in cement, or bitumen, or polymer. Possible reaction mechanisms are identified and the effects of temperature and pressure are evaluated. Estimations of the production of combustible gases (which also have the potential to form explosive mixtures) have been taken from the literature. The implications of gas production for pressurisation (and possible rupture) of waste drums and of a repository are assessed. Waste-treatment schemes for the reduction of gas-generation capacity of several waste-types are highlighted. Recommendations for further work are summarised. (author)

  3. Extraction of actinides and fission products ions by non-chelating N,N'-tetraalkyldiamides

    International Nuclear Information System (INIS)

    Charbonnel, M.C.; Musikas, C.

    1986-09-01

    N,N-dialkylmonoamides, are good extractants of metallic ions. They were considered as alternative to TBP in nuclear fuels reprocessing. The present paper deals with the extractive properties of N,N'-tetrabutylglutaramide. N,N'-tetraalkyldiamides of dicarboxylic acids except malonamides do not extract the trivalent actinides and lanthanides from aqueous HNO, solutions probably because there is no favourable ligand conformation to chelate the metallic ions. This feature is interesting for the nuclear fuel reprocessing since the presence of a second amide group could lead to new selectivities and to radiolytic and solvolytic degradation products easier to handle. We will present the investigation results of HNO 3 U(VI), Pu(IV) and fission products extraction by TBGA in toluene from HNO 3 aqueous solution. 5 figs, 6 refs

  4. Stable Organic Neutral Diradical via Reversible Coordination.

    Science.gov (United States)

    Lu, Zhenpin; Quanz, Henrik; Burghaus, Olaf; Hofmann, Jonas; Logemann, Christian; Beeck, Sebastian; Schreiner, Peter R; Wegner, Hermann A

    2017-12-27

    We report the formation of a stable neutral diboron diradical simply by coordination of an aromatic dinitrogen compound to an ortho-phenyldiborane. This process is reversible upon addition of pyridine. The diradical species is stable above 200 °C. Computations are consistent with an open-shell triplet diradical with a very small open-shell singlet-triplet energy gap that is indicative of the electronic disjointness of the two radical sites. This opens a new way of generating stable radicals with fascinating electronic properties useful for a large variety of applications.

  5. The separation of stable water-in-oil emulsions

    International Nuclear Information System (INIS)

    Velicogna, D.; Koundakjiian, A.; Beausejour, I.

    1993-01-01

    Stable oil-in-water emulsions are a major problem in the recovery of spilled oils. Such emulsions can contain as little as 10% oil and can have properties very different from the original oils, making their storage and disposal difficult. These problems have led to experiments testing the feasibility of a process for separating these stable emulsions into dischargeable water and reusable oil. The technique investigated involves use of a recyclable solvent to remove the oil and subsequent distillation and/or membrane treatment to recover the oil and recycle the solvent. Results of preliminary tests show that stable water-in-oil emulsions can be separated quite readily with a regenerated solvent system. The only products of these systems are oil, which can be sent to a refinery, and dischargeable water. The recycled solvent can be used many times without any significant decrease in separation efficiency. In order to enhance the throughput of the system, a solvent vapor stripping method was invented. This stripping method also improves the quality of the products and the recycled solvent. Membrane methods can be used as a post-treatment for the produced water in order to achieve more adequate compliance with discharge limits. 4 refs., 3 figs., 5 tabs

  6. A simple route to prepare stable hydroxyapatite nanoparticles suspension

    Science.gov (United States)

    Han, Yingchao; Wang, Xinyu; Li, Shipu

    2009-07-01

    A simple ultrasound assisted precipitation method with addition of glycosaminoglycans (GAGs) is proposed to prepare stable hydroxyapatite (HAP) nanoparticles suspension from the mixture of Ca(H2PO4)2 solution and Ca(OH)2 solution. The product was characterized by XRD, FT-IR, TEM, HRTEM and particle size, and zeta potential analyzer. TEM observation shows that the suspension is composed of 10-20 nm × 20-50 nm short rod-like and 10-30 nm similar spherical HAP nanoparticles. The number-averaged particle size of stable suspension is about 30 nm between 11.6 and 110.5 nm and the zeta potential is -60.9 mV. The increase of stability of HAP nanoparticles suspension mainly depends on the electrostatic effect and steric effect of GAGs. The HAP nanoparticles can be easily transported into the cancer cells and exhibit good potential as gene or drug carrier system.

  7. Application of Stable Isotope Signatures in Food Traceability

    International Nuclear Information System (INIS)

    Nazaratul Ashifa Abdullah Salim; Roslanzairi Mostapha; Zainon Othman; Nor Afiqah Harun; Mohd Suhaimi Hamzah; Shamsiah Abdul Rahman; Md Suhaimi Elias; Salmah Moosa

    2015-01-01

    Stable isotope analysis has widely been used to trace the origin of organic materials in various fields, such as geochemistry, biochemistry, archaeology and petroleum. In past a decade, it has also become an important tool for food traceability study. The globalization of food markets and the relative ease with which food commodities are transported through and between countries and continents, means that consumers are increasingly concerned about the origin of the foods they eat. The natural abundance isotope variation such as carbon, nitrogen, hydrogen and oxygen are use as geographic tracers or marker to determine the geographic origin of fruits, crop, vegetables and food products from animal. The isotopic compositions of plant materials reflect various factors such as isotopic compositions of source materials and their assimilation processes as well as growth environments. This paper will discuss on stable carbon and nitrogen isotopic compositions in rice, advantages, limitations and potential of other analysis applications that can be incorporated in food traceability system. (author)

  8. Neutron inelastic scattering measurements on the stable isotopes of titanium

    Science.gov (United States)

    Olacel, A.; Belloni, F.; Borcea, C.; Boromiza, M.; Dessagne, P.; Henning, G.; Kerveno, M.; Negret, A.; Nyman, M.; Pirovano, E.; Plompen, A. J. M.

    2017-07-01

    The results of a neutron inelastic scattering experiment performed at the Geel Electron Linear Accelerator pulsed white neutron source of the European Commission Joint Research Centre are reported. The neutrons with energies up to 18 MeV interacted with a natTi sample and the γ rays resulting from inelastic scattering reactions on the stable isotopes were detected using the Gamma Array for Inelastic Neutron Scattering (GAINS) spectrometer. We were able to measure the γ -production cross sections for 21 transitions in the five stable Ti isotopes. From these, the level cross sections and the total inelastic cross sections were determined. Our experimental results are compared with theoretical calculations performed using the talys 1.8 code, evaluated nuclear data libraries, and also with previously reported results.

  9. On the stable Mg-Zn-Y quasicrystals

    Science.gov (United States)

    Luo, Z. P.; Sui, H. X.; Zhang, S. Q.

    1996-07-01

    By the conventional air-cooled casting method, bulk ingots with a large fraction of stable Mg-Zn-Y icosahedral quasicrystals, both simple and face-centered, were obtained. The quasicrystal structures were directly confirmed by high-resolution electron microscopy (HREM) observations. The electron diffraction patterns from the quasicrystals were studied by computer simulations. A coexisting crys-talline phase of the quasicrystals was identified as the Mg7Zn3 phase, which was proved to be the (1/1) approximant of the quasicrystals. The quasicrystals were stable during a continuous heating process. However, at high temperature, oxidation occurred, and thus, Y2O3 and MgO products were formed. Oxidation at high temperatures is characteristic for the Mg-Zn-Y alloys and differs from Al-base alloys.

  10. Development of O-18 stable isotope separation technology using membrane

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae Woo; Kim, Taek Soo; Choi, Hwa Rim; Park, Sung Hee; Lee, Ki Tae; Chang, Dae Shik

    2006-06-15

    The ultimate goal of this investigation is to develop the separation technology for O-18 oxygen stable isotope used in a cyclotron as a target for production of radioisotope F-18. F-18 is a base material for synthesis of [F-18]FDG radio-pharmaceutical, which is one of the most important tumor diagnostic agent used in PET (Positron Emission Tomography). More specifically, this investigation is focused on three categories as follow, 1) development of the membrane distillation isotope separation process to re-enrich O-18 stable isotope whose isotopic concentration is reduced after used in a cyclotron, 2) development of organic impurity purification technology to remove acetone, methanol, ethanol, and acetonitrile contained in a used cyclotron O-18 enriched target water, and 3) development of a laser absorption spectroscopic system for analyzing oxygen isotopic concentration in water.

  11. Stable Isotope Group 1983 progress report

    International Nuclear Information System (INIS)

    Stewart, M.K.

    1984-06-01

    The work of the Stable Isotope Group of the Institute of Nuclear Sciences in the fields of isotope geology, isotope hydrology, geochronology, isotope biology and related fields, and mass spectrometer instrumentation, during 1983, is described

  12. Stable Isotope Group 1982 progress report

    International Nuclear Information System (INIS)

    Stewart, M.K.

    1983-06-01

    The work of the Stable Isotope Group of the Institute of Nuclear Sciences during 1982, in the fields of isotope geology, isotope hydrology, geochronology, isotope biology and mass spectrometer instrumentation, is described

  13. Bartolome Island, Galapagos Stable Oxygen Calibration Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Galapagos Coral Stable Oxygen Calibration Data. Sites: Bartolome Island: 0 deg, 17'S, 90 deg 33' W. Champion Island: 1 deg, 15'S, 90 deg, 05' W. Urvina Bay (Isabela...

  14. Allan Hills Stable Water Isotopes, Version 1

    Data.gov (United States)

    National Aeronautics and Space Administration — This data set includes stable water isotope values at 10 m resolution along an approximately 5 km transect through the main icefield of the Allan Hills Blue Ice...

  15. Tannaka duality and stable infinity-categories

    OpenAIRE

    Iwanari, Isamu

    2014-01-01

    We introduce the notion of fine tannakian infinity-categories and prove Tannaka duality results for symmetric monoidal stable infinity-categories over a field of characteristic zero. We also discuss several examples.

  16. On Stable Marriages and Greedy Matchings

    Energy Technology Data Exchange (ETDEWEB)

    Manne, Fredrik; Naim, Md; Lerring, Hakon; Halappanavar, Mahantesh

    2016-12-11

    Research on stable marriage problems has a long and mathematically rigorous history, while that of exploiting greedy matchings in combinatorial scientific computing is a younger and less developed research field. In this paper we consider the relationships between these two areas. In particular we show that several problems related to computing greedy matchings can be formulated as stable marriage problems and as a consequence several recently proposed algorithms for computing greedy matchings are in fact special cases of well known algorithms for the stable marriage problem. However, in terms of implementations and practical scalable solutions on modern hardware, the greedy matching community has made considerable progress. We show that due to the strong relationship between these two fields many of these results are also applicable for solving stable marriage problems.

  17. The Reactivity of Stable Metallacyclobutenes and Vinylcarbenes

    OpenAIRE

    Holland, Ryan Lynn

    2016-01-01

    Chapter 1. Historical Development of Stable Metallacyclobutenes Fred Tebbe and co-workers synthesized the first stable metallacyclobutene complexes in the late 1970’s by treatment of an intermediate titanium methylene species – later popularized as the “Tebbe reagent” – with acetylenes. Robert Grubbs at Caltech further studied this system, using it to detail a degenerate metathesis reaction and to isolate a metallacyclobutane complex – which was implicated in the emerging field of alkene meta...

  18. Stable atomic hydrogen: Polarized atomic beam source

    International Nuclear Information System (INIS)

    Niinikoski, T.O.; Penttilae, S.; Rieubland, J.M.; Rijllart, A.

    1984-01-01

    We have carried out experiments with stable atomic hydrogen with a view to possible applications in polarized targets or polarized atomic beam sources. Recent results from the stabilization apparatus are described. The first stable atomic hydrogen beam source based on the microwave extraction method (which is being tested ) is presented. The effect of the stabilized hydrogen gas density on the properties of the source is discussed. (orig.)

  19. Properties of stable nonstoichiometric nanoceria produced by thermal plasma

    Science.gov (United States)

    Lan, Yuan-Pei; Sohn, Hong Yong; Mohassab, Yousef; Liu, Qingcai; Xu, Baoqiang

    2017-08-01

    Thermally stable blue nonstoichiometric nanoceria was produced by feeding nanoceria with an average size of 50 nm into a DC thermal plasma reactor. The effects of different plasma power levels and atmospheres were investigated. XRD results showed the ceria lattice parameter increased with plasma power. SEM and TEM results showed that the shape of nanoparticles changed after plasma treatment; the blue nonstoichiometric nanoceria had highly regular shapes such as triangular pyramids and polyhedral in contrast to the irregular shape of the raw nanoceria. Significant downshift was found in the Raman spectra of the plasma products, with a 7.9-cm-1 shift compared with raw nanoceria, which was explained by the reduction of Ce4+. X-ray photoelectron spectroscopy results showed that the Ce3+ fraction increased from 14% in the raw nanoceria to 38-39% for the product CeO2- x , indicating the high reduction state on the ceria surface. It was determined that this blue nonstoichiometric nanoceria was stable up to 400 °C in air, but the color changed to pale yellow after 4 h at 500 °C in air indicating oxidation to CeO2. Additionally, this novel stable nano-CeO2- x caused a red shift in the UV-visible absorption results; a 48-nm red shift occurred for the nonstoichiometric nanoceria produced at 15 kW compared with the raw nanoceria. The band gap was calculated to be 2.5 eV while it was 3.2 eV for the raw nanoceria, indicating that this novel stable blue nonstoichiometric nanoceria should be a promising material for optical application.

  20. On the habitability of universes without stable deuterium

    Science.gov (United States)

    Adams, Fred C.; Grohs, Evan

    2017-05-01

    In both stars and in the early universe, the production of deuterium is the first step on the way to producing heavier nuclei. If the strong force were slightly weaker, then deuterium would not be stable, and many authors have noted that nuclesynthesis would be compromised so that helium production could not proceed through standard reaction chains. Motivated by the possibility that other regions of space-time could have different values for the fundamental constants, this paper considers stellar evolution in universes without stable deuterium and argues that such universes can remain habitable. Even in universes with no stellar nucleosynthesis, stars can form and will generate energy through gravitational contraction. Using both analytic estimates and a state-of-the-art stellar evolution code, we show that such stars can be sufficiently luminous and long-lived to support life. Stars with initial masses that exceed the Chandrasekhar mass cannot be supported by degeneracy pressure and will explode at the end of their contraction phase. The resulting explosive nucleosynthesis can thus provide the universe with some heavy elements. We also explore the possibility that helium can be produced in stellar cores through a triple-nucleon reaction that is roughly analogous to the triple-alpha reaction that operates in our universe. Stars burning hydrogen through this process are somewhat hotter than those in our universe, but otherwise play the same role. Next we show that with even trace amounts (metallicity Z ∼10-10) of heavy elements - produced through the triple-nucleon process or by explosive nucleosynthesis - the CNO cycle can operate and allow stars to function. Finally, we consider Big Bang Nucleosynthesis without stable deuterium and find that only trace amounts of helium are produced, with even smaller abundances of other nuclei. With stars evolving through gravitational contraction, explosive nucleosynthesis, the triple-nucleon reaction, and the CNO cycle

  1. Radiolytic removal of trihalomethane in chlorinated seawater

    International Nuclear Information System (INIS)

    Rajamohan, R.; Rajesh, Puspalata; Venugopalan, V.P.; Rangarajan, S.; Natesan, Usha

    2015-01-01

    Biofouling is one of the major operational problems in seawater cooling systems. It is controlled by application of chlorine based biocides in the range of 0.5-2.0 mg L -1 . The bromide in seawater reacts with the added chlorine and forms hypobromous acid. The brominated residual biocides react with natural organic matter present in the seawater, resulting in the formation of trihalomethanes (THM) such as bromoform (CHBr 3 ), dibromochloromethane (CHBr 2 Cl) bromodichloromethane (CHBrCl 2 ). Though THMs represent a small fraction of the added chlorine, they are relatively more persistent than residual chlorine, and hence pose a potential hazard to marine life because of their reported mutagenicity. There have been few reports on removal of THMs from chlorinated seawater. In this work, the efficacy of gamma irradiation technique for the removal of THMs from chlorine-dosed seawater was investigated. Experiments were carried out using seawater collected from Kalpakkam. Irradiation study was conducted in chlorinated (1, 3, and 5 mg L -1 of Cl 2 ) seawater by applying various dosages (0.4-5.0 kGy) of gamma radiation using a 60 Co Gamma Chamber 5000. Bromoform showed a faster rate of degradation as compared to other halocarbons like bromodichloromethane and dibromochloromethane. This shows the change in total THM concentration with variation in the radiation dose and initial Cl 2 dosing. When the percentage degradation of all the three trihalomethane species was compared with applied doses, it was found that the maximum reduction occurred at a dose of 2.5 kGy. The reduction was almost similar for all the three doses (1, 3, 5 ppm of Cl 2 ) used for chlorination. With a further increase in radiation dose to 5.0 kGy, a slight increase in reduction was observed

  2. Radiolytic and thermolytic bubble gas hydrogen composition

    Energy Technology Data Exchange (ETDEWEB)

    Woodham, W. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-12-11

    This report describes the development of a mathematical model for the estimation of the hydrogen composition of gas bubbles trapped in radioactive waste. The model described herein uses a material balance approach to accurately incorporate the rates of hydrogen generation by a number of physical phenomena and scale the aforementioned rates in a manner that allows calculation of the final hydrogen composition.

  3. Radiolytic and hydrolytic stability of extractant molecules

    Energy Technology Data Exchange (ETDEWEB)

    Cames, B.; Caniffi, B.; Rudloff, D. [CEA Marcoule - DRCP/SCPS/LCSE: BP 17171, Bagnols-sur-Ceze, 30207 cedex (France)

    2008-07-01

    In nuclear spent fuel reprocessing industry, actinide partitioning processes are based on solvent extraction and organic phase recycling. It is well-known that both radiolysis and acidic hydrolysis leads to degradation of extractant molecules. To have more information on the stability of extractant molecules used in a reprocessing plant, batch studies have been carried out to determine parameters governing the extractant consumption kinetic under hydrolysis and radiolysis effects (dose rate, degradation time and nitric acidity of the organic phase). For gamma radiation, results about DMDOHEMA (N,N'-dimethyl-N,N'-di-octyl-hexyl-ethoxy-malonamide) and DEHiBA (N,N'-di(ethyl-2-hexyl)iso-butanamide) show that degradation of DMDOHEMA and DEHiBA depends only on nitric acidity of the organic phase, dose rate and radiolysis time (DMDOHEMA consumption kinetic constant is 2 times slower than for DEHiBA). For same degradation conditions, it has been shown that {alpha}-radiolysis of DMDOHEMA is 4 times slower than {gamma}-radiolysis, and acidic hydrolysis of DMDOHEMA is effective whereas that of DEHiBA is not. (authors)

  4. Local Search Approaches in Stable Matching Problems

    Directory of Open Access Journals (Sweden)

    Toby Walsh

    2013-10-01

    Full Text Available The stable marriage (SM problem has a wide variety of practical applications, ranging from matching resident doctors to hospitals, to matching students to schools or, more generally, to any two-sided market. In the classical formulation, n men and n women express their preferences (via a strict total order over the members of the other sex. Solving an SM problem means finding a stable marriage where stability is an envy-free notion: no man and woman who are not married to each other would both prefer each other to their partners or to being single. We consider both the classical stable marriage problem and one of its useful variations (denoted SMTI (Stable Marriage with Ties and Incomplete lists where the men and women express their preferences in the form of an incomplete preference list with ties over a subset of the members of the other sex. Matchings are permitted only with people who appear in these preference lists, and we try to find a stable matching that marries as many people as possible. Whilst the SM problem is polynomial to solve, the SMTI problem is NP-hard. We propose to tackle both problems via a local search approach, which exploits properties of the problems to reduce the size of the neighborhood and to make local moves efficiently. We empirically evaluate our algorithm for SM problems by measuring its runtime behavior and its ability to sample the lattice of all possible stable marriages. We evaluate our algorithm for SMTI problems in terms of both its runtime behavior and its ability to find a maximum cardinality stable marriage. Experimental results suggest that for SM problems, the number of steps of our algorithm grows only as O(n log(n, and that it samples very well the set of all stable marriages. It is thus a fair and efficient approach to generate stable marriages. Furthermore, our approach for SMTI problems is able to solve large problems, quickly returning stable matchings of large and often optimal size, despite the

  5. Biosynthesis of stable isotope 15N labeled spirulina

    International Nuclear Information System (INIS)

    Ren Zheng; Du Xiaoning; Hou Jinghua; Zhang Jingmei

    2010-01-01

    The spirulina is a phototrophic organism. It was considered as the best of nutritional health product. The nitrogen atoms of spirulina was replaced with 15 N stable isotope by the method of biosynthesis. So 15 N labeled spirulina is a nutritional health product and stable isotope tracer product. As a tracer, 15 N labeled spirulina plays an irreplaceable part in bioscience, medicine metabolism and pathology metabolism and so on. 15 N label spirulina is cultivated only in a small scale because of expensive 15 N material. The culture temperature, shine intensity, pH for spirulina were studied. Some feasible conditions were obtained such as 25℃, 3000-4000 lux, initial pH9.0 in the room. 15 N label spirulin prescription was obtained via orthogonal experiment. The optimize prescription of spirulina was that sodium bicarbonate was 13 g · L-1, 15 N-urea was 0.2 g · L -1 , potassium phosphate dibasic was 0.6 g · L -1 , and glucose was 2 g · L -1 . The cost of 15 N material has a significant reduction. The abundance was more than 98%. (authors)

  6. Air-stable ink for scalable, high-throughput layer deposition

    Science.gov (United States)

    Weil, Benjamin D; Connor, Stephen T; Cui, Yi

    2014-02-11

    A method for producing and depositing air-stable, easily decomposable, vulcanized ink on any of a wide range of substrates is disclosed. The ink enables high-volume production of optoelectronic and/or electronic devices using scalable production methods, such as roll-to-roll transfer, fast rolling processes, and the like.

  7. Stable chaos in fluctuation driven neural circuits

    International Nuclear Information System (INIS)

    Angulo-Garcia, David; Torcini, Alessandro

    2014-01-01

    Highlights: • Nonlinear instabilities in fluctuation driven (balanced) neural circuits are studied. • Balanced networks display chaos and stable phases at different post-synaptic widths. • Linear instabilities coexists with nonlinear ones in the chaotic regime. • Erratic motion appears also in linearly stable phase due to stable chaos. - Abstract: We study the dynamical stability of pulse coupled networks of leaky integrate-and-fire neurons against infinitesimal and finite perturbations. In particular, we compare mean versus fluctuations driven networks, the former (latter) is realized by considering purely excitatory (inhibitory) sparse neural circuits. In the excitatory case the instabilities of the system can be completely captured by an usual linear stability (Lyapunov) analysis, whereas the inhibitory networks can display the coexistence of linear and nonlinear instabilities. The nonlinear effects are associated to finite amplitude instabilities, which have been characterized in terms of suitable indicators. For inhibitory coupling one observes a transition from chaotic to non chaotic dynamics by decreasing the pulse-width. For sufficiently fast synapses the system, despite showing an erratic evolution, is linearly stable, thus representing a prototypical example of stable chaos

  8. Metabolic studies in man using stable isotopes

    International Nuclear Information System (INIS)

    Faust, H.; Jung, K.; Krumbiegel, P.

    1993-01-01

    In this project, stable isotope compounds and stable isotope pharmaceuticals were used (with emphasis on the application of 15 N) to study several aspects of nitrogen metabolism in man. Of the many methods available, the 15 N stable isotope tracer technique holds a special position because the methodology for application and nitrogen isotope analysis is proven and reliable. Valid routine methods using 15 N analysis by emission spectrometry have been demonstrated. Several methods for the preparation of biological material were developed during our participation in the Coordinated Research Programme. In these studies, direct procedures (i.e. use of diluted urine as a samples without chemical preparation) or rapid isolation methods were favoured. Within the scope of the Analytical Quality Control Service (AQCS) enriched stable isotope reference materials for medical and biological studies were prepared and are now available through the International Atomic Energy Agency. The materials are of special importance as the increasing application of stable isotopes as tracers in medical, biological and agricultural studies has focused interest on reliable measurements of biological material of different origin. 24 refs

  9. Radioactive and stable elements' concentration in medicinal plants from Brazil

    International Nuclear Information System (INIS)

    Sussa, F.V.; Silva, P.S.C.; Damatto, S.R.; Favaro, D.I.T.; Mazzilli, B.P.

    2009-01-01

    Since the early days of mankind, plants have been used as food and for medicinal purposes. Still, little information exists in literature about the activity concentration of 238 U and 232 Th decay products, as well as stable element concentrations in Brazilian plants. Activity concentrations of 226 Ra, 228 Ra and 210 Pb, and chemical concentrations of As, Ba, Br, Cs, Co, Cr, Cu, Eu, Fe, Hf, La, Lu, Rb, Sb, Sc, Sm, Ta, Tb, Yb, Zn and Zr were determined in ten samples commonly used in Brazilian medicinal plants. (author)

  10. 5-Hydroxymethylcytosine is a predominantly stable DNA modification

    OpenAIRE

    Bachman, Martin; Uribe-Lewis, Santiago; Yang, Xiaoping; Williams, Michael; Murrell, Adele; Balasubramanian, Shankar

    2014-01-01

    5-Hydroxymethylcytosine (hmC) is an oxidation product of 5-methylcytosine (mC) present in DNA of most mammalian cells. Reduction of hmC levels in DNA is a hallmark of cancers. Elucidating the dynamics of this oxidation reaction and the lifetime of hmC in DNA is fundamental to understanding hmC function. Using stable isotope labeling of cytosine derivatives in the DNA of mammalian cells and ultrasensitive tandem liquid-chromatography mass spectrometry (LCMS), we show that the majority of hmC i...

  11. Extraordinarily stable disulfide-linked homodimer of human growth hormone

    OpenAIRE

    Grigorian, Alexei L.; Bustamante, Juan J.; Hernandez, Peter; Martinez, Andrew O.; Haro, Luis S.

    2005-01-01

    Although a 22-kDa human growth hormone (hGH) is the predicted protein product of the hGH-N gene, a pleiotropic collection of uncharacterized molecular weight and charge isoforms is also produced. Using chromatography and preparative SDS-PAGE under reducing conditions we isolated an unusually stable mercaptoethanol-resistant (MER) 45-kDa hGH. A 5-h incubation at 100°C in the presence of 2-mercaptoethanol was required to convert approximately 90% of MER-45-kDa hGH into a 22-kDa hGH. Other reduc...

  12. Policy on stable iodine prophylaxis following nuclear reactor accidents (1989)

    International Nuclear Information System (INIS)

    1989-09-01

    This policy considers the alleviation of possible hazards that may arise from any radioiodines inhaled from a plume of fission products emanating from a nuclear reactor accident. Such a nuclear reactor may be land or ship-based. In any accident that releases radioiodines to the environment, one countermeasure that may need to be considered to reduce the effect of inhalation of radioiodines by persons downwind of the point of release is to provide those persons with tablets containing stable iodine. Both potassium iodide (KI) and potassium iodate (KIO 3 ) are recommended as effective prophylactics tablets for this purpose in Australia. Action levels, doses and contraindicatories are briefly outlined

  13. Stable Superstring Relics and Ultrahigh Energy Cosmic Rays

    CERN Document Server

    Coriano, Claudio; Plumacher, Michael; Coriano, Claudio; Faraggi, Alon E.; Plumacher, Michael

    2001-01-01

    One of the most intriguing experimental results of recent years is the observation of Ultrahigh Energy Cosmic Rays (UHECRs) above the GZK cutoff. Plausible candidates for the UHECR primaries are the decay products of a meta--stable matter state with mass of order O(10^{12-15 GeV}), which simultaneously is a good cold dark matter candidate. We study possible meta-stable matter states that arise from Wilson line breaking of GUT symmetries in semi-realistic heterotic string models. In the models that we study the exotic matter states can be classified according to patterns of SO(10) symmetry breaking. We show that cryptons, which are states that carry fractional electric charge $\\pm1/2$, and are confined by a hidden gauge group cannot produce viable dark matter. This is due to the fact that, in addition to the lightest neutral bound state, cryptons give rise to meta-stable charged bound states. However, these states may still account for the UHECR events. We argue that the uniton, which is an exotic Standard Mod...

  14. Application of Stable Isotope Signatures in Food Traceability

    International Nuclear Information System (INIS)

    Nazaratul Ashifa Abdullah Salim; Roslanzairi Mostapha; Zainon Othman

    2016-01-01

    Stable isotope analysis has widely been used to trace the origin of organic materials in various fields, such as geochemistry, biochemistry, archaeology and petroleum. In past a decade, it has also become an important tool for food traceability study. The globalisation of food markets and the relative ease which food commodities are transported through and between countries and continents means that consumers are increasingly concerned about the origin of the foods they eat. The natural abundance of stable isotope variation such as carbon, nitrogen, hydrogen and oxygen are used as geographic tracers or marker to determine the geographic origin of fruits, crop, vegetables and food products from animal. The isotopic compositions of plant materials reflect various factors such as isotopic compositions of source materials and their assimilation processes as well as growth environments. This paper will discuss on stable carbon and nitrogen isotopic compositions in rice that been determined by Isotope Ratio Mass Spectrometry, advantages, limitations and potential of other analysis applications that can be incorporated in food traceability system. (author)

  15. Identification of stable fly attractant compounds in vinasse, a byproduct of sugarcane-ethanol distillation.

    Science.gov (United States)

    Jelvez Serra, N S; Goulart, H F; Triana, M F; Dos Santos Tavares, S; Almeida, C I M; DA Costa, J G; Santana, A E G; Zhu, J J

    2017-12-01

    The stable fly, Stomoxys calcitrans (Diptera: Muscidae), is a worldwide pest of livestock. Recent outbreaks of stable flies in sugarcane fields in Brazil have become a serious problem for livestock producers. Larvae and pupae found inside sugarcane stems after harvesting may indicate that stable flies use these stems as potential oviposition or larval development sites. Field observations suggest that outbreaks of stable flies are associated with the vinasse and filter cake derived from biomass distillation in sugarcane ethanol production that are used as fertilizers in sugarcane fields. Adult stable flies are attracted to vinasse, which appears to present an ideal larval development site. The primary goal of the present study is to demonstrate the role of vinasse in influencing the sensory physiological and behavioural responses of stable flies, and to identify its associated volatile attractant compounds. Both laboratory and field studies showed that vinasse is extremely attractive to adult stable flies. Chemical analyses of volatiles collected revealed a wide range of carboxylic acids, alcohols, phenols and aldehydes as potential attractant compounds. These newly identified attractants could be used to develop a tool for the attractant-baited mass trapping of stable flies in order to reduce infestations. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

  16. Nanocomposites from Stable Dispersions of Carbon Nanotubes in Polymeric Matrices Using Dispersion Interaction

    Science.gov (United States)

    Wise, Kristopher Eric (Inventor); Park, Cheol (Inventor); Kang, Jin Ho (Inventor); Siochi, Emilie J. (Inventor); Harrison, Joycelyn S. (Inventor)

    2016-01-01

    Stable dispersions of carbon nanotubes (CNTs) in polymeric matrices include CNTs dispersed in a host polymer or copolymer whose monomers have delocalized electron orbitals, so that a dispersion interaction results between the host polymer or copolymer and the CNTs dispersed therein. Nanocomposite products, which are presented in bulk, or when fabricated as a film, fiber, foam, coating, adhesive, paste, or molding, are prepared by standard means from the present stable dispersions of CNTs in polymeric matrices, employing dispersion interactions, as presented hereinabove.

  17. Temperature and Humidity Control in Livestock Stables

    DEFF Research Database (Denmark)

    Hansen, Michael; Andersen, Palle; Nielsen, Kirsten M.

    2010-01-01

    The paper describes temperature and humidity control of a livestock stable. It is important to have a correct air flow pattern in the livestock stable in order to achieve proper temperature and humidity control as well as to avoid draught. In the investigated livestock stable the air flow...... is controlled using wall mounted ventilation flaps. In the paper an algorithm for air flow control is presented meeting the needs for temperature and humidity while taking the air flow pattern in consideration. To obtain simple and realisable controllers a model based control design method is applied....... In the design dynamic models for temperature and humidity are very important elements and effort is put into deriving and testing the models. It turns out that non-linearities are dominating in both models making feedback linearization the natural design method. The air controller as well as the temperature...

  18. On some topological properties of stable measures

    DEFF Research Database (Denmark)

    Nielsen, Carsten Krabbe

    1996-01-01

    Summary The paper shows that the set of stable probability measures and the set of Rational Beliefs relative to a given stationary measure are closed in the strong topology, but not closed in the topology of weak convergence. However, subsets of the set of stable probability measures which...... are characterized by uniformity of convergence of the empirical distribution are closed in the topology of weak convergence. It is demonstrated that such subsets exist. In particular, there is an increasing sequence of sets of SIDS measures who's union is the set of all SIDS measures generated by a particular...... system and such that each subset consists of stable measures. The uniformity requirement has a natural interpretation in terms of plausibility of Rational Beliefs...

  19. Manual for the Use of Stable Isotopes in Entomology

    International Nuclear Information System (INIS)

    2009-06-01

    result of problem driven inquisitiveness and technological advances, and are framed by the social and political environment. Although the external environment may mould the technological path, a technology will only become obsolete if there are viable substitution products or methods. Stable isotope methods are a substitute for many radionuclide methods. The progress made in stable isotope science over the past twenty years is a direct result of the interplay of the above factors. Stable isotopes are omnipresent in the environment and pose no health or environmental risks. Advances in isotope ratio mass spectrometry in terms of detection, accuracy and automation have broadened experimental possibilities immensely over the past twenty years. It was recognised that there was significant potential for answering many of the entomologist?s biological and ecological questions using stable isotopes, an expertise the Soil Science Unit of the FAO/IAEA Agriculture and Biotechnology Laboratory in Seibersdorf had long fostered; therefore collaboration with the Entomology Unit at the same Laboratory was established. A number of collaborative experiments were carried and subsequently published. It was soon recognised that stable isotopes have tremendous potential in entomological research and although there were numerous studies using stable isotopes in ecology, their use in entomology per se was limited. Thus it was felt that a publication was required to make stable isotope techniques more widely known among entomologists. This manual will attempt to provide an introduction to the use of stable isotopes in entomological research. It will strive to communicate the basic principles and techniques of stable isotope science and provide a springboard for further interest and research in this area

  20. Gas production due to alpha particle degradation of polyethylene and polyvinylchloride

    International Nuclear Information System (INIS)

    Reed, D.T.; Hoh, J.; Emery, J.; Okajima, S.; Krause, T.

    1998-07-01

    Alpha particle degradation experiments were performed on polyethylene (PE) and polyvinylchloride (PVC) plastic samples typical of Westinghouse Savannah River Company (WSRC) transuranic (TRU) waste. This was done to evaluate the effects of sealing TRU waste during shipment. Experiments were conducted at three temperatures using low dose rates. Predominant products from both plastics were hydrogen, carbon dioxide, and various organic species, with the addition of hydrochloric acid from PVC. In all experiments, the total pressure decreased. Irradiation at 30 and 60 C and at various dose rates caused small changes for both plastics, but at 100 C coupled thermal-radiolytic effects included discoloration of the material as well as large differences in the gas phase composition

  1. Faster and Simpler Approximation of Stable Matchings

    Directory of Open Access Journals (Sweden)

    Katarzyna Paluch

    2014-04-01

    Full Text Available We give a 3 2 -approximation algorithm for finding stable matchings that runs in O(m time. The previous most well-known algorithm, by McDermid, has the same approximation ratio but runs in O(n3/2m time, where n denotes the number of people andm is the total length of the preference lists in a given instance. In addition, the algorithm and the analysis are much simpler. We also give the extension of the algorithm for computing stable many-to-many matchings.

  2. Stable isotopes in Lithuanian bioarcheological material

    Science.gov (United States)

    Skipityte, Raminta; Jankauskas, Rimantas; Remeikis, Vidmantas

    2015-04-01

    Investigation of bioarcheological material of ancient human populations allows us to understand the subsistence behavior associated with various adaptations to the environment. Feeding habits are essential to the survival and growth of ancient populations. Stable isotope analysis is accepted tool in paleodiet (Schutkowski et al, 1999) and paleoenvironmental (Zernitskaya et al, 2014) studies. However, stable isotopes can be useful not only in investigating human feeding habits but also in describing social and cultural structure of the past populations (Le Huray and Schutkowski, 2005). Only few stable isotope investigations have been performed before in Lithuanian region suggesting a quite uniform diet between males and females and protein intake from freshwater fish and animal protein. Previously, stable isotope analysis has only been used to study a Stone Age population however, more recently studies have been conducted on Iron Age and Late medieval samples (Jacobs et al, 2009). Anyway, there was a need for more precise examination. Stable isotope analysis were performed on human bone collagen and apatite samples in this study. Data represented various ages (from 5-7th cent. to 18th cent.). Stable carbon and nitrogen isotope analysis on medieval populations indicated that individuals in studied sites in Lithuania were almost exclusively consuming C3 plants, C3 fed terrestrial animals, and some freshwater resources. Current investigation demonstrated social differences between elites and country people and is promising in paleodietary and daily life reconstruction. Acknowledgement I thank prof. dr. G. Grupe, Director of the Anthropological and Palaeoanatomical State Collection in Munich for providing the opportunity to work in her laboratory. The part of this work was funded by DAAD. Antanaitis-Jacobs, Indre, et al. "Diet in early Lithuanian prehistory and the new stable isotope evidence." Archaeologia Baltica 12 (2009): 12-30. Le Huray, Jonathan D., and Holger

  3. Bordism, stable homotopy and adams spectral sequences

    CERN Document Server

    Kochman, Stanley O

    1996-01-01

    This book is a compilation of lecture notes that were prepared for the graduate course "Adams Spectral Sequences and Stable Homotopy Theory" given at The Fields Institute during the fall of 1995. The aim of this volume is to prepare students with a knowledge of elementary algebraic topology to study recent developments in stable homotopy theory, such as the nilpotence and periodicity theorems. Suitable as a text for an intermediate course in algebraic topology, this book provides a direct exposition of the basic concepts of bordism, characteristic classes, Adams spectral sequences, Brown-Peter

  4. Modelling stable water isotopes: Status and perspectives

    Directory of Open Access Journals (Sweden)

    Werner M.

    2010-12-01

    Full Text Available Modelling of stable water isotopes H2 18O and HDO within various parts of the Earth’s hydrological cycle has clearly improved our understanding of the interplay between climatic variations and related isotope fractionation processes. In this article key principles and major research results of stable water isotope modelling studies are described. Emphasis is put on research work using explicit isotope diagnostics within general circulation models as this highly complex model setup bears many resemblances with studies using simpler isotope modelling approaches.

  5. Impact of β- radiolysis and transient products on irradiation-enhanced corrosion of zirconium alloys

    International Nuclear Information System (INIS)

    Lemaignan, C.

    1992-01-01

    An analysis has been undertaken of the various cases of local enhancement of the corrosion rate of zirconium alloys under irradiation. It is observed that in most cases a strong emission of energetic β - is present leading to a local energy desorption rate higher than the core average. This suggests that the local transient radiolytic oxidising species produced in the coolant by the β - particles could contribute to corrosion enhancement, by increasing the local corrosion potential. This process is applicable to the local enhanced corrosion found in front of stainless steels structural parts, due to the contribution of Mn, in front of Pt inserts and Cu-rich cruds. It explains also the irradiation corrosion enhancement of Cu-rich Zr alloys. Enhanced corrosion around neutron absorbing material is explained similarly by pair production from conversion of high energy capture photons in the cladding, leading to energetic electrons. The same process was found to be active with other highly ionising species like α in Ni-rich alloys and fission products in homogeneous reactors. This mechanism, applicable for an explanation of localised irradiation-enhanced corrosion, is proposed to be extended to the reactor core, where the general enhancement of Zr-alloy corrosion under irradiation would be due to the general radiolysis. It suggests that care should be taken to avoid any source of β - emission or other ionising species in the reactor core that could give an increase of energy deposition rate for radiolysis. Also the corrosion testing conditions for the materials to be used in reactors have to be relevant to the radiolytic environments found in the reactor cores. (orig.)

  6. Petrography, compositional characteristics and stable isotope ...

    African Journals Online (AJOL)

    Petrography, compositional characteristics and stable isotope geochemistry of the Ewekoro formation from Ibese Corehole, eastern Dahomey basin, southwestern Nigeria. ME Nton, MO ... Preserved pore types such as; intercrystaline, moldic and vuggy pores were observed as predominant conduits for fluids. The major ...

  7. petrography, compositional characteristics and stable isotope ...

    African Journals Online (AJOL)

    PROF EKWUEME

    Subsurface samples of the predominantly carbonate Ewekoro Formation, obtained from Ibese core hole within the Dahomey basin were used in this study. Investigations entail petrographic, elemental composition as well as stable isotopes (carbon and oxygen) geochemistry in order to deduce the different microfacies and ...

  8. Substitution of stable isotopes in Chlorella

    Science.gov (United States)

    Flaumenhaft, E.; Katz, J. J.; Uphaus, R. A.

    1969-01-01

    Replacement of biologically important isotopes in the alga Chlorella by corresponding heavier stable isotopes produces increasingly greater deviations from the normal cell size and changes the quality and distribution of certain cellular components. The usefulness of isotopically altered organisms increases interest in the study of such permuted organisms.

  9. Champion Island, Galapagos Stable Oxygen Calibration Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Galapagos Coral Stable Oxygen Calibration Data. Sites: Bartolome Island: 0 deg, 17 min S, 90 deg 33 min W. Champion Island: 1 deg, 15 min S, 90 deg, 05 min W. Urvina...

  10. Stable propagation of 'selfish'genetic elements

    Indian Academy of Sciences (India)

    Unknown

    viruses such as the Epstein-Barr virus (Harris et al 1985;. Kanda et al 2001) and bovine papilloma virus (Lehman and Botchan 1998; Ilves et al 1999), which exist pre- dominantly as extrachromosomal episomes, have been shown to utilize chromosome tethering as a means for stable segregation. The tethering mechanism ...

  11. Facies, dissolution seams and stable isotope compositions

    Indian Academy of Sciences (India)

    Stable isotope analysis of the limestone shows that 13C and 18O values are compatible with the early Mesoproterozoic open seawater composition. The ribbon limestone facies in the Rohtas Limestone is characterized by micritic beds, each decoupled in a lower band enriched and an upper band depleted in dissolution ...

  12. Connected domination stable graphs upon edge addition ...

    African Journals Online (AJOL)

    A set S of vertices in a graph G is a connected dominating set of G if S dominates G and the subgraph induced by S is connected. We study the graphs for which adding any edge does not change the connected domination number. Keywords: Connected domination, connected domination stable, edge addition ...

  13. Stable magnetic remanence in antiferromagnetic goethite.

    Science.gov (United States)

    Strangway, D W; McMahon, B E; Honea, R M

    1967-11-10

    Goethite, known to be antiferromagnetic, acquires thermoremanent magnetization at its Neel temperature of 120 degrees C. This remanence, extremely stable, is due to the presence of unbalanced spins in the antiferromagnetic structure; the spins may result from grain size, imperfections, or impurities.

  14. Strontium stable isotope behaviour accompanying basalt weathering

    Science.gov (United States)

    Burton, K. W.; Parkinson, I. J.; Gíslason, S. G. R.

    2016-12-01

    The strontium (Sr) stable isotope composition of rivers is strongly controlled by the balance of carbonate to silicate weathering (Krabbenhöft et al. 2010; Pearce et al. 2015). However, rivers draining silicate catchments possess distinctly heavier Sr stable isotope values than their bedrock compositions, pointing to significant fractionation during weathering. Some have argued for preferential release of heavy Sr from primary phases during chemical weathering, others for the formation of secondary weathering minerals that incorporate light isotopes. This study presents high-precision double-spike Sr stable isotope data for soils, rivers, ground waters and estuarine waters from Iceland, reflecting both natural weathering and societal impacts on those environments. The bedrock in Iceland is dominantly basaltic, d88/86Sr ≈ +0.27, extending to lighter values for rhyolites. Geothermal waters range from basaltic Sr stable compositions to those akin to seawater. Soil pore waters reflect a balance of input from primary mineral weathering, precipitation and litter recycling and removal into secondary phases and vegetation. Rivers and ground waters possess a wide range of d88/86Sr compositions from +0.101 to +0.858. Elemental and isotope data indicate that this fractionation primarily results from the formation or dissolution of secondary zeolite (d88/86Sr ≈ +0.10), but also carbonate (d88/86Sr ≈ +0.22) and sometimes anhydrite (d88/86Sr ≈ -0.73), driving the residual waters to heavier or lighter values, respectively. Estuarine waters largely reflect mixing with seawater, but are also be affected by adsorption onto particulates, again driving water to heavy values. Overall, these data indicate that the stability and nature of secondary weathering phases, exerts a strong control on the Sr stable isotope composition of silicate rivers. [1] Krabbenhöft et al. (2010) Geochim. Cosmochim. Acta 74, 4097-4109. [2] Pearce et al. (2015) Geochim. Cosmochim. Acta 157, 125-146.

  15. Shelf-stable food through high dose irradiation

    International Nuclear Information System (INIS)

    Placek, V.; Svobodova, V.; Bartonicek, B.; Rosmus, J.; Camra, M.

    2004-01-01

    Irradiation of food with high doses (radappertization) is a way, how to prepare shelf-stable ready-to-eat food. The radappertization process requires that the food be heated at first to an internal temperature of at least 75 deg. C to inactivate autolytic enzyme, which could cause the spoilage during storage without refrigeration. In order to prevent radiation induced changes in sensory properties (off flavors, odors, undesirable color change, etc.) the food was vacuum packed and irradiated in frozen state at -30 deg. C or less to a minimum dose of 35 kGy. Such products have characteristics of fresh food prepared for eating even if they are stored for long time under tropical conditions. The wholesomeness (safety for consumption) has been confirmed during 40 years of testing. Within the NRI Rez 10 kinds of shelf-stable meat products have been prepared. The meat was cooked, vacuum packed in SiO x -containing pouch, freezed in liquid nitrogen and irradiated with electron beam accelerator. The microbial, chemical, and organoleptic properties have been tested

  16. A model to secure a stable iodine concentration in milk

    Directory of Open Access Journals (Sweden)

    Gisken Trøan

    2015-12-01

    Full Text Available Background: Dairy products account for approximately 60% of the iodine intake in the Norwegian population. The iodine concentration in cow's milk varies considerably, depending on feeding practices, season, and amount of iodine and rapeseed products in cow fodder. The variation in iodine in milk affects the risk of iodine deficiency or excess in the population. Objective: The first goal of this study was to develop a model to predict the iodine concentration in milk based on the concentration of iodine and rapeseed or glucosinolate in feed, as a tool to securing stable iodine concentration in milk. A second aim was to estimate the impact of different iodine levels in milk on iodine nutrition in the Norwegian population. Design: Two models were developed on the basis of results from eight published and two unpublished studies from the past 20 years. The models were based on different iodine concentrations in the fodder combined with either glucosinolate (Model 1 or rapeseed cake/meal (Model 2. To illustrate the impact of different iodine concentrations in milk on iodine intake, we simulated the iodine contribution from dairy products in different population groups based on food intake data in the most recent dietary surveys in Norway. Results: The models developed could predict iodine concentration in milk. Cross-validation showed good fit and confirmed the explanatory power of the models. Our calculations showed that dairy products with current iodine level in milk (200 µg/kg cover 68, 49, 108 and 56% of the daily iodine requirements for men, women, 2-year-old children, and pregnant women, respectively. Conclusions: Securing a stable level of iodine in milk by adjusting iodine concentration in different cow feeds is thus important for preventing excess intake in small children and iodine deficiency in pregnant and non-pregnant women.

  17. Production yields of 2-alkylcyclobutanones in irradiated foods

    International Nuclear Information System (INIS)

    Marchioni, E.; Ennahar, S.

    2009-01-01

    2-alkycyclobutanones are formed by irradiation exclusively, and are considered as unique radiolytic product (URP). Because of the URP character of the 2-alkycyclobutanones, these compounds are good marker of irradiation treatment. The European Committee for Standardization (CEN) developed an analytical method (EN 1785) for detection of 2-alkycyclobutanones having a detection limit of 0.2 pmol, limiting the application to foodstuffs treated for microbial disinfection (doses > 0.5 kGy), with fat content higher than 1.0 g %. The use of this EN 1785 and the supercritical extraction analytical methods allowed the determination of the production yields of 2-alkycyclobutanones in broad range of foodstuffs. The obtained production yields were between 0.20 and 12.21 nmol/mmol fatty acid/kGy), and showed strong dependency from he nature of the food matrix. The amount 2-alkycyclobutanones intake from irradiated foodstuffs by consumer calculated based on production yields determined in this work show, that the doses used in toxicological studies were much higher, than that are consumed by human through eating irradiated foods. (author)

  18. Laboratory and field methods for stable isotope analysis in human biology.

    Science.gov (United States)

    Reitsema, Laurie J

    2015-01-01

    Stable isotope analysis (SIA; carbon, hydrogen, nitrogen, sulfur, and oxygen) of human tissues offers a means for assessing diet among living humans. Stable isotope ratios of broad categories of food and drink food vary systematically, and stable isotope ratios in consumer tissues represent a composite of the isotopic ratios of food and drink consumed during an individual's life. Isotopic evidence for diet is independent of errors in informant recall, and accrues during time periods when researchers are absent. Beyond diet reconstruction, tissue stable isotope ratios are sensitive to excursions from homeostasis, such as starvation and rapid growth. Because of their relationship to diet, geographic location, hydration, and nutritional status, stable isotope signatures in human tissues offer a window into human biocultural adaptations, past and present. This article describes methods for SIA that may be usefully applied in studies of living humans, with emphasis placed on carbon and nitrogen. Some of the ecological, physiological, and evolutionary applications of stable isotope data among living humans are discussed. By incorporating SIA in research, human biologists facilitate a productive dialog with bioarchaeologists, who routinely use stable isotope evidence, mingling different perspectives on human biology and behavior. © 2015 Wiley Periodicals, Inc.

  19. On The Roman Domination Stable Graphs

    Directory of Open Access Journals (Sweden)

    Hajian Majid

    2017-11-01

    Full Text Available A Roman dominating function (or just RDF on a graph G = (V,E is a function f : V → {0, 1, 2} satisfying the condition that every vertex u for which f(u = 0 is adjacent to at least one vertex v for which f(v = 2. The weight of an RDF f is the value f(V (G = Pu2V (G f(u. The Roman domination number of a graph G, denoted by R(G, is the minimum weight of a Roman dominating function on G. A graph G is Roman domination stable if the Roman domination number of G remains unchanged under removal of any vertex. In this paper we present upper bounds for the Roman domination number in the class of Roman domination stable graphs, improving bounds posed in [V. Samodivkin, Roman domination in graphs: the class RUV R, Discrete Math. Algorithms Appl. 8 (2016 1650049].

  20. Design of optically stable image reflector system.

    Science.gov (United States)

    Tsai, Chung-Yu

    2013-08-01

    The design of a partially optically stable (POS) reflector system, in which the exit ray direction and image pose are unchanged as the reflector system rotates about a specific directional vector, was presented in an earlier study by the current group [Appl. Phys. B100, 883-890 (2010)]. The present study further proposes an optically stable image (OSI) reflector system, in which not only is the optical stability property of the POS system retained, but the image position and total ray path length are also fixed. An analytical method is proposed for the design of OSI reflector systems comprising multiple reflectors. The validity of the proposed approach is demonstrated by means of two illustrative examples.

  1. Stable microfluidic flow focusing using hydrostatics.

    Science.gov (United States)

    Gnyawali, Vaskar; Saremi, Mohammadali; Kolios, Michael C; Tsai, Scott S H

    2017-05-01

    We present a simple technique to generate stable hydrodynamically focused flows by driving the flow with hydrostatic pressure from liquid columns connected to the inlets of a microfluidic device. Importantly, we compare the focused flows generated by hydrostatic pressure and classical syringe pump driven flows and find that the stability of the hydrostatic pressure driven technique is significantly better than the stability achieved via syringe pumps, providing fluctuation-free focused flows that are suitable for sensitive microfluidic flow cytometry applications. We show that the degree of flow focusing with the hydrostatic method can be accurately controlled by the simple tuning of the liquid column heights. We anticipate that this approach to stable flow focusing will find many applications in microfluidic cytometry technologies.

  2. Utilization of stable isotopes in medicine

    International Nuclear Information System (INIS)

    1980-11-01

    The ten lectures given at this round table are presented together with a discussion. Five lectures, relating to studies in which deuterium oxide was employed as a tracer of body water, dealt with pulmonary water measurements in man and animals, the total water pool in adipose subjects, and liquid compartments in children undergoing hemodyalisis. The heavy water is analysed by infrared spectrometry and a new double spectrodoser is described. Two studies using 13 C as tracer, described the diagnosis of liver troubles and diabetes respectively. A general review of the perspectives of the application of stable isotopes in clinical medicine is followed by a comparison of the use of stable and radioactive isotopes in France [fr

  3. Thermally Stable, Latent Olefin Metathesis Catalysts

    OpenAIRE

    Thomas, Renee M.; Fedorov, Alexey; Keitz, Benjamin K.; Grubbs, Robert H.

    2011-01-01

    Highly thermally stable N-aryl,N-alkyl N-heterocyclic carbene (NHC) ruthenium catalysts were designed and synthesized for latent olefin metathesis. These catalysts showed excellent latent behavior toward metathesis reactions, whereby the complexes were inactive at ambient temperature and initiated at elevated temperatures, a challenging property to achieve with second generation catalysts. A sterically hindered N-tert-butyl substituent on the NHC ligand of the ruthenium complex was found to i...

  4. The nature of stable insomnia phenotypes.

    Science.gov (United States)

    Pillai, Vivek; Roth, Thomas; Drake, Christopher L

    2015-01-01

    We examined the 1-y stability of four insomnia symptom profiles: sleep onset insomnia; sleep maintenance insomnia; combined onset and maintenance insomnia; and neither criterion (i.e., insomnia cases that do not meet quantitative thresholds for onset or maintenance problems). Insomnia cases that exhibited the same symptom profile over a 1-y period were considered to be phenotypes, and were compared in terms of clinical and demographic characteristics. Longitudinal. Urban, community-based. Nine hundred fifty-four adults with Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition based current insomnia (46.6 ± 12.6 y; 69.4% female). None. At baseline, participants were divided into four symptom profile groups based on quantitative criteria. Follow-up assessment 1 y later revealed that approximately 60% of participants retained the same symptom profile, and were hence judged to be phenotypes. Stability varied significantly by phenotype, such that sleep onset insomnia (SOI) was the least stable (42%), whereas combined insomnia (CI) was the most stable (69%). Baseline symptom groups (cross-sectionally defined) differed significantly across various clinical indices, including daytime impairment, depression, and anxiety. Importantly, however, a comparison of stable phenotypes (longitudinally defined) did not reveal any differences in impairment or comorbid psychopathology. Another interesting finding was that whereas all other insomnia phenotypes showed evidence of an elevated wake drive both at night and during the day, the 'neither criterion' phenotype did not; this latter phenotype exhibited significantly higher daytime sleepiness despite subthreshold onset and maintenance difficulties. By adopting a stringent, stability-based definition, this study offers timely and important data on the longitudinal trajectory of specific insomnia phenotypes. With the exception of daytime sleepiness, few clinical differences are apparent across stable phenotypes.

  5. A belief-based evolutionarily stable strategy

    OpenAIRE

    Deng, Xinyang; Wang, Zhen; Liu, Qi; Deng, Yong; Mahadevan, Sankaran

    2014-01-01

    As an equilibrium refinement of the Nash equilibrium, evolutionarily stable strategy (ESS) is a key concept in evolutionary game theory and has attracted growing interest. An ESS can be either a pure strategy or a mixed strategy. Even though the randomness is allowed in mixed strategy, the selection probability of pure strategy in a mixed strategy may fluctuate due to the impact of many factors. The fluctuation can lead to more uncertainty. In this paper, such uncertainty involved in mixed st...

  6. Stable iodine prophylaxis. Recommendations of the 2nd UK Working Group on Stable Iodine Prophylaxis

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    The Working Group reviewed the revised Who guidance and the information published since 1991 on the risks of thyroid cancer in children from radioiodine and the risks of side effects from stable iodine. In particular, it reviewed data compiled on the incidence of thyroid cancers in children following the accident at the Chernobyl nuclear power plant in 1986. It considered whether the NRPB Earls were still appropriate, in the light of the new data. It also reviewed a range of other recommendations given by the 1st Working Group, concerning the chemical form of stable iodine tablets and practical issues concerning implementation of stable iodine prophylaxis. Finally, it reviewed the Patient Information Leaflet that is required, by law, to be included in each box of tablets and provided suggestions for information to be included in a separate information leaflet to be handed out to the public when stable iodine tablets are distributed.

  7. Detonation of Meta-stable Clusters

    Energy Technology Data Exchange (ETDEWEB)

    Kuhl, Allen; Kuhl, Allen L.; Fried, Laurence E.; Howard, W. Michael; Seizew, Michael R.; Bell, John B.; Beckner, Vincent; Grcar, Joseph F.

    2008-05-31

    We consider the energy accumulation in meta-stable clusters. This energy can be much larger than the typical chemical bond energy (~;;1 ev/atom). For example, polymeric nitrogen can accumulate 4 ev/atom in the N8 (fcc) structure, while helium can accumulate 9 ev/atom in the excited triplet state He2* . They release their energy by cluster fission: N8 -> 4N2 and He2* -> 2He. We study the locus of states in thermodynamic state space for the detonation of such meta-stable clusters. In particular, the equilibrium isentrope, starting at the Chapman-Jouguet state, and expanding down to 1 atmosphere was calculated with the Cheetah code. Large detonation pressures (3 and 16 Mbar), temperatures (12 and 34 kilo-K) and velocities (20 and 43 km/s) are a consequence of the large heats of detonation (6.6 and 50 kilo-cal/g) for nitrogen and helium clusters respectively. If such meta-stable clusters could be synthesized, they offer the potential for large increases in the energy density of materials.

  8. Two stable steady states in the Hodgkin-Huxley axons

    OpenAIRE

    Aihara, K.; Matsumoto, G.

    1983-01-01

    Two stable steady states were found in the numerical solution of the Hodgkin-Huxley equations for the intact squid axon bathed in potassium-rich sea water with an externally applied inward current. Under the conditions the two stable steady-states exist, the Hodgkin-Huxley equations have a complex bifurcation structure including, in addition to the two stable steady-states, a stable limit cycle, two unstable equilibrium points, and one asymptotically stable equilibrium point. It was also conc...

  9. Stable isotopes for improving human nutrition

    International Nuclear Information System (INIS)

    Uauy, Ricardo

    2001-01-01

    Full text: The developing regions of the world are undergoing a rapid demographic and epidemiological transition. The number of child deaths and disease, and their causes, are important markers for this change and serve as indices of human development. More important to society at large is the change in the pattern of child growth of the survivors. Although they survive, a large proportion of children in developing countries fail to grow physically and develop mentally, thereby affecting not only health but also educational performance and economic productivity. National development is retarded at its root. In societies undergoing demographic transition, decreases in fertility rates usually lag behind changes in mortality by several decades. Thus, rapid population growth is typical of this transition. Dietary determinants of nutrition and health of populations undergoing transition also change. Typically, predominantly cereal-based food consumption patterns change to ones incorporating a greater proportion of animal food products, higher total fat and saturated fats, and a progressive inclusion of industrially processed food in the diet. The rural poor come to the cities and become the urban poor. They tend to live in precarious housing in unsanitary environments. Working merely for subsistence, they place great demands on governments to provide health and education services. The political dimension of these unsatisfied demands, in terms of unmet basic human needs, characterises life in developing societies. This situation not only fuels political struggles but is also the cause of great frustration to concerned scientists and health professionals. The impact of nutrition on infant survival and child growth is at the heart of what matters in the developing regions of the world. Most countries undergoing the nutrition transition have supplementary feeding programs and other major nutrition interventions targeted mainly at the urban and rural poor. For example, a

  10. Biological factors of natural and artificial ecosystems stable (unstable) functioning

    Science.gov (United States)

    Pechurkin, Nikolai S.

    The problem of sustainable development of humanity on Earth and the problem of supporting human life in space have the same scientific and methodological bases. The key to solve both problems is a long term maintenance of balanced material cycle. As a whole, natural or artificial ecosystems are to be more closed than open, but their elements (links of systems) are to be substantially open in interactions with each other. Prolonged stable interactions of different links have to have unique joint results - closed material cycling or biotic turnover. It is necessary to include, at least, three types of main links into any system to support real material cycling: producers, consumers, reducers. Producer links are now under studies in many laboratories. It is evident that the higher productivity of link, the lower link stability. Especially, it concerns with parasite impact to plants. As usual, artificial ecosystems are more simple (incomplete) than natural ecosystems, sometimes, they have not enough links for prolonged stable functioning. For example, life support system for space flight can be incomplete in consumer link, having only some crew persons, instead of interacting populations of consumers. As for reducer link, it is necessary to "organize" a special coordinated work of microbial biocenoses to fulfill proper cycling. Possible evolution of links, their self development is a matter of special attention for the maintenance of prolonged stable functioning. It's the most danger for systems with populations of quickly reproducing, so-called, R - strategists, according to symbols of logistic equation. From another side, quick reproduction of R - strategists is able to increase artificial ecosystems and their links functioning. After some damages of system, R - strategist's link can be quickly "self repaired" up to level of normal functioning. Some experimental data of this kind and mathematical models are to be discussed in the paper. This work is supported by

  11. Vegetation engineers marsh morphology through multiple competing stable states

    Science.gov (United States)

    Marani, Marco; Da Lio, Cristina; D’Alpaos, Andrea

    2013-01-01

    Marshes display impressive biogeomorphic features, such as zonation, a mosaic of extensive vegetation patches of rather uniform composition, exhibiting sharp transitions in the presence of extremely small topographic gradients. Although generally associated with the accretion processes necessary for marshes to keep up with relative sea level rise, competing environmental constraints, and ecologic controls, zonation is still poorly understood in terms of the underlying biogeomorphic mechanisms. Here we find, through observations and modeling interpretation, that zonation is the result of coupled geomorphological–biological dynamics and that it stems from the ability of vegetation to actively engineer the landscape by tuning soil elevation within preferential ranges of optimal adaptation. We find multiple peaks in the frequency distribution of observed topographic elevation and identify them as the signature of biologic controls on geomorphodynamics through competing stable states modulated by the interplay of inorganic and organic deposition. Interestingly, the stable biogeomorphic equilibria correspond to suboptimal rates of biomass production, a result coherent with recent observations. The emerging biogeomorphic structures may display varying degrees of robustness to changes in the rate of sea level rise and sediment availability, with implications for the overall resilience of marsh ecosystems to climatic changes. PMID:23401529

  12. Optical bi-stable shutter development/improvement

    Science.gov (United States)

    Lizon, J. L.; Haddad, N.; Castillo, R.

    2012-09-01

    Two of the VLT instruments (Giraffe and VIMOS) are using the large magnetic E/150 from Prontor (with an aperture diameter of 150 mm). As we were facing an unacceptable number of failures with this component some improvement plan was discussed already in 2004. The final decision for starting this program was conditioned by the decision from the constructor to stop the production. The opportunity was taken to improve the design building a fully bi-stable mechanism in order to reduce the thermal dissipation. The project was developed in collaboration between the two main ESO sites doing the best use of the manpower and of the technical capability available at the two centers. The project took advantage of the laser Mask Manufacturing Unit and the invar sheets used to prepare the VIMOS MOS mask to fabricate the shutter petals. Our paper describes the development including the intensive and long optimization period. To conclude this optimization we proceed with a long life test on two units. These units have demonstrate a very high level of reliability (up to 100 000 cycles without failure which can be estimated to an equivalent 6 years of operation of the instrument) A new bi-stable shutter driver and controller have also been developed. Some of the highlights of this unit are the fully configurable coil driving parameters, usage of braking strategy to dump mechanical vibration and reduce mechanical wearing, configurable usage of OPEN and CLOSE sensors, non volatile storage of parameters, user friendly front panel interface.

  13. Chemistry of Stable Carbenes and «Green» Technologies

    Directory of Open Access Journals (Sweden)

    Korotkikh, N.I.

    2015-11-01

    Full Text Available Brief analysis of fundamental research in the chemistry of stable carbenes and applications in the field of «green» chemistry on their basis carried out at the L.M. Litvinenko Institute of Physical Organic & Coal Chemistry of NAS of Ukraine over the last decade is given. Carbene versions of ester Claisen condensation to form zwitterionic compounds, the Leuckart-Wallach reaction with the autoreduction of carbenoid azolium salts, Hofmann cleavage of aminocarbene insertion products, an induced tandem autotransformation of 1,2,4-triazol-5-ylidenes into 5-amidino-1,2,4-triazoles were found. New carbene reactions of ad dition, deesterification, oxidation and complexation were revealed. Effective methods of obtaining stable carbenes and carbenoids were suggested. New types of carbenes, namely benzimidazolylidenes, superstable conjugated biscarbenes and new types of carbenoids were synthesized. The existence of hypernucleophilic carbenes was theoretically predicted and experimentally confirmed. The prospects of the use of carbenes and their derivatives, in particular, carbene complexes of transition metals in catalysis of organic reactions and the search of biologically active compounds were shown.

  14. Biomedical research applications of electromagnetically separated enriched stable isotopes

    International Nuclear Information System (INIS)

    Lambrecht, R.M.

    1982-01-01

    The current and projected annual requirements through 1985 for stable isotopes enriched by electromagnetic separation methods were reviewed for applications in various types of biomedical research: (1) medical radiosotope production, labeled compounds, and potential radiopharmaceuticals; (2) nutrition, food science, and pharmacology; (3) metallobiochemistry and environmental toxicology; (4) nuclear magnetic resonance, electron paramagnetic resonance, and Moessbauer spectroscopy in biochemical, biophysical, and biomedical research; and (5) miscellaneous advances in radioactive and non-radioactive tracer technology. Radioisotopes available from commercial sources or routinely used in clinical nuclear medicine were excluded. Priorities and summaries are based on statements in the references and from answers to a survey conducted in the fall of 1981. Current requirements for enriched stable isotopes in biomedical research are not being satisfied. Severe shortages exist for 26 Mg, 43 Ca, 70 Zn, 76 Se, 78 Se, 102 Pd, 111 Cd, 113 Cd, and 190 Os. Many interesting and potentially important investigations in biomedical research require small quantities of specific elements at high isotopic enrichments

  15. 5-Hydroxymethylcytosine is a predominantly stable DNA modification

    Science.gov (United States)

    Bachman, Martin; Uribe-Lewis, Santiago; Yang, Xiaoping; Williams, Michael; Murrell, Adele; Balasubramanian, Shankar

    2015-01-01

    5-Hydroxymethylcytosine (hmC) is an oxidation product of 5-methylcytosine (mC) present in DNA of most mammalian cells. Reduction of hmC levels in DNA is a hallmark of cancers. Elucidating the dynamics of this oxidation reaction and the lifetime of hmC in DNA is fundamental to understanding hmC function. Using stable isotope labeling of cytosine derivatives in the DNA of mammalian cells and ultrasensitive tandem liquid-chromatography mass spectrometry (LCMS), we show that the majority of hmC is a stable modification, as opposed to a transient intermediate. In contrast with DNA methylation, which occurs immediately during replication, hmC forms slowly over the first 30 h following DNA synthesis. Isotopic labeling of DNA in mouse tissues confirmed the stability of hmC in vivo and demonstrated a relationship between global levels of hmC and cell proliferation. These insights have important implications for understanding the states of chemically modified DNA bases in health and disease. PMID:25411882

  16. Stable isotope applications in biomolecular structure and mechanisms. A meeting to bring together producers and users of stable-isotope-labeled compounds to assess current and future needs

    Energy Technology Data Exchange (ETDEWEB)

    Trewhella, J.; Cross, T.A.; Unkefer, C.J. [eds.

    1994-12-01

    Knowledge of biomolecular structure is a prerequisite for understanding biomolecular function, and stable isotopes play an increasingly important role in structure determination of biological molecules. The first Conference on Stable Isotope Applications in Biomolecular Structure and Mechanisms was held in Santa Fe, New Mexico, March 27--31, 1994. More than 120 participants from 8 countries and 44 institutions reviewed significant developments, discussed the most promising applications for stable isotopes, and addressed future needs and challenges. Participants focused on applications of stable isotopes for studies of the structure and function of proteins, peptides, RNA, and DNA. Recent advances in NMR techniques neutron scattering, EPR, and vibrational spectroscopy were highlighted in addition to the production and synthesis of labeled compounds. This volume includes invited speaker and poster presentations as well as a set of reports from discussion panels that focused on the needs of the scientific community and the potential roles of private industry, the National Stable Isotope Resource, and the National High Magnetic Field Laboratory in serving those needs. This is the leading abstract. Individual papers are processed separately for the database.

  17. Stable isotope applications in biomolecular structure and mechanisms. A meeting to bring together producers and users of stable-isotope-labeled compounds to assess current and future needs

    International Nuclear Information System (INIS)

    Trewhella, J.; Cross, T.A.; Unkefer, C.J.

    1994-12-01

    Knowledge of biomolecular structure is a prerequisite for understanding biomolecular function, and stable isotopes play an increasingly important role in structure determination of biological molecules. The first Conference on Stable Isotope Applications in Biomolecular Structure and Mechanisms was held in Santa Fe, New Mexico, March 27--31, 1994. More than 120 participants from 8 countries and 44 institutions reviewed significant developments, discussed the most promising applications for stable isotopes, and addressed future needs and challenges. Participants focused on applications of stable isotopes for studies of the structure and function of proteins, peptides, RNA, and DNA. Recent advances in NMR techniques neutron scattering, EPR, and vibrational spectroscopy were highlighted in addition to the production and synthesis of labeled compounds. This volume includes invited speaker and poster presentations as well as a set of reports from discussion panels that focused on the needs of the scientific community and the potential roles of private industry, the National Stable Isotope Resource, and the National High Magnetic Field Laboratory in serving those needs. This is the leading abstract. Individual papers are processed separately for the database

  18. Microbiological characterization of stable resuspended dust

    Directory of Open Access Journals (Sweden)

    Nora Kováts

    2016-06-01

    Full Text Available Objectives: Air quality in the stables is characterized by elevated level of dust and aeroallergens which are supposed to directly cause or exacerbate several respiratory disorders. The most often recognized problem is recurrent airway obstruction (RAO, previously known as chronic obstructive pulmonary disease (COPD. There is some indication that aeroallergens (among them endotoxins may also cause inflammation in human airways and may exceed safe levels in stables. Monitoring studies have covered mainly the determination of the concentration of respirable particles and of culturable fungi and their toxins. However, these particles do not only directly affect the respiratory system, but might act as a carrier conveying toxic contaminants and biological agents such as bacteria. In a typical, 20-horse Hungarian stable, microbial community of respirable fraction of resuspended dust has been characterized to reveal if these particles convey hazardous pathogenic bacteria, posing risk to either horses or staff. Material and Methods: Resuspended dust was sampled using a mobile instrument. The instrument contains a PARTISOL-FRM model 2000 sampler that was operated at a flow rate of 16.7 l/min and a cyclone separator which collected the particulate matter with an aerodynamic size between 1 μm and 10 μm (PM1–10 fraction. Microbial taxa were identified by culture-independent next generation sequencing (NGS of variable 16S ribosomal ribonucleic acid (rRNA gene regions. Results: In total, 1491 different taxa were identified, of them 384 were identified to species level, 961 to genus level. The sample was dominated by common ubiquitous soil and organic material-dwelling taxa. Conclusions: Pathogens occurred at low abundance, and were represented by mostly facultative human pathogens, with the prevalence of Staphylococcus species.

  19. Stable channel of reclaimed tidal lowland

    Science.gov (United States)

    Syarifudin, Achmad; Imanuddin, Momon S.; Moerwanto, Arie S.; Suryadi, F. X.

    2017-11-01

    This study aimed to develop models of the Operation and Maintenance in the reclaimed tidal marsh area to get a stable channel. The research location is reclaimed tidal delta area Telang I Primary 8 representing land typology A/B and a survey conducted in 13 South Secondary Schemes following existing tertiary Telang I. MIKE - 11 computer models used used to analyze the movement of sediment in the channel in both the Primary channel 8, SPD, SDU and tertiary channels in block 13 South. Calibration model with multiple channels in the field of physical parameters has been performed to obtain results close to the results of measurement modeling sediment movement in the channel. The integration models of MIKE - 11 models with various scenarios are used to model the operation and maintenance of the channel in the tidal marsh area to get a stable channel. According to the scheme P8 - 13S, OM models obtained 75 percent, in which the secondary channel (SPD/SDU) and built flap gate in tertiary channel, get a well prototype model of the stable channel (equilibriums), where the average erosion on P8 at a distance of 3,200 m in the amount of 4,472,049 m3 and the mean sedimentation in the SPD of 963,836 m3 and mean of sedimentation in the tertiary channel of 3,508,213 m3. Similarly, on average erosion P8 by 4,135,649 m3 and the mean sedimentation in the SDU of 681,304 m3 and the mean sedimentation in the tertiary channel of 3,454,345 m3.

  20. Preservation of food products by irradiation

    International Nuclear Information System (INIS)

    McGivney, W.T.

    1988-01-01

    The use of irradiation to preserve food has the potential to significantly enhance our capacity to maximize the quality and quantity of the food we consume. In a world in which distribution of food occurs across continents and in which malnourished populations are in dire need of basic food products, any safe, effective, and efficient means of preserving food is more than welcome. Irradiation, as a method for food preservation, has been studied for more than 30 years. This discussion focuses on this most recent method for the preservation of food with particular emphasis on its effects on the safety, nutritive, and aesthetic values of the food preserved by irradiation. The use of ionizing radiation as a method to preserve foods is one that has been demonstrated to be effective for a variety of food classes. Irradiation offers a means to decontaminate, disinfest, and retard the spoilage of the food supply. At the same time, it appears that the wholesomeness of these food products is maintained. Nutritive value can be sustained by use of effective doses of radiation. Concerns over the safety of irradiated food are rooted in questions regarding the potential induction of radioactivity, harmful radiolytic products, and pathogenic radiation-resistant or mutant strains of microorganisms. Research findings have allayed concerns over safety. However, more research is necessary to conclusively resolve these safety issues. Food irradiation is a promising technology that has and will contribute to our ability to feed the people of this world. This technology is but one of many available ways to preserve our greatest natural resource, the food supply. Enhancement of the ability to preserve food by irradiation will facilitate the distribution of food from fertile developed regions to the malnourished peoples of underdeveloped countries. 21 references

  1. Aggressive Fibromatosis: Evidence for a Stable Phase

    Directory of Open Access Journals (Sweden)

    Gillian Mitchell

    1998-01-01

    Full Text Available Purpose. Aggressive fibromatosis (AF is an uncommon locally infiltrating benign disease of soft tissue for which treatment comprises complete surgical resection. Radiotherapy can be given postoperatively if the margin is incompletely resected. If the tumour is inoperable radiotherapy provides an alternative treatment. Hormone therapy and cytotoxic chemotherapy have also been used for unresectable or recurrent disease. All treatment modalities carry an associated morbidity. We believe that the natural history of aggressive fibromatosis may include a period of stable disease without progression, during which time, treatment is not always necessary.

  2. Stable isogeometric analysis of trimmed geometries

    Science.gov (United States)

    Marussig, Benjamin; Zechner, Jürgen; Beer, Gernot; Fries, Thomas-Peter

    2017-04-01

    We explore extended B-splines as a stable basis for isogeometric analysis with trimmed parameter spaces. The stabilization is accomplished by an appropriate substitution of B-splines that may lead to ill-conditioned system matrices. The construction for non-uniform knot vectors is presented. The properties of extended B-splines are examined in the context of interpolation, potential, and linear elasticity problems and excellent results are attained. The analysis is performed by an isogeometric boundary element formulation using collocation. It is argued that extended B-splines provide a flexible and simple stabilization scheme which ideally suits the isogeometric paradigm.

  3. Remarks on stable and quasi-stable k-strings at large N

    International Nuclear Information System (INIS)

    Armoni, A.; Shifman, M.

    2003-01-01

    We discuss k-strings in the large-N Yang-Mills theory and its supersymmetric extension. Whereas the tension of the bona fide (stable) QCD string is expected to depend only on the N-ality of the representation, tensions that depend on specific representation R are often reported in the lattice literature. In particular, adjoint strings are discussed and found in certain simulations. We clarify this issue by systematically exploiting the notion of the quasi-stable strings which becomes well-defined at large N. The quasi-stable strings with representation-dependent tensions decay, but the decay rate (per unit length per unit time) is suppressed as Λ 2 F(N) where F(N) falls off as a function of N. It can be determined on the case-by-case basis. The quasi-stable strings eventually decay into stable strings whose tension indeed depends only on the N-ality. We also briefly review large-N arguments showing why the Casimir formula for the string tension cannot be correct, and present additional arguments in favor of the sine formula. Finally, we comment on the relevance of our estimates to Euclidean lattice measurements

  4. Towards stable catalysts by control over the collective features of supported metal nanoparticles

    NARCIS (Netherlands)

    Prieto, G.; Zecevic, J.|info:eu-repo/dai/nl/341386715; Friedrich, H.|info:eu-repo/dai/nl/304837350; de Jong, K.P.|info:eu-repo/dai/nl/06885580X; de Jongh, P.E.|info:eu-repo/dai/nl/186125372

    2013-01-01

    Supported metal nanoparticles play a pivotal role in areas such as nanoelectronics, energy storage/conversion1 and as catalysts for the sustainable production of fuels and chemicals2–4. However, the tendency of nanoparticles to grow into larger crystallites is an impediment for stable

  5. Heterologous stable expression of terpenoid biosynthetic genes using the moss Physcomitrella patens

    DEFF Research Database (Denmark)

    Bach, Søren Spanner; King, Brian Christopher; Zhan, Xin

    2014-01-01

    , such as streamlining of large scale Agrobacterium infiltration and upregulation of the upstream pathways, transient in planta heterologous expression quickly reaches limitations when used for production of terpenoids. Stable integration of transgenes into the nuclear genome of the moss Physcomitrella patens has...

  6. Towards stable access to EU markets for the Beninese shrimp chain

    NARCIS (Netherlands)

    Adékambi, S.A.; Dabade, D.S.; Kindji, K.; Besten, den H.M.W.; Faure, M.; Nout, M.J.R.; Sogbossi, B.; Ingenbleek, P.T.M.

    2016-01-01

    Traditionally, the economy of Benin has strongly depended on a single crop, namely cotton. Since 2006, the Beninese government has aimed to diversify exports, in particular focussing on high-value export products such as shrimp. Stable market access for shrimps is, however, hindered by their

  7. Highly thermal-stable and functional cellulose nanocrystals and nanofibrils produced using fully recyclable organic acids

    Science.gov (United States)

    Liheng Chen; Junyong Zhu; Carlos Baez; Peter Kitin; Thomas Elder

    2016-01-01

    Here we report the production of highly thermal stable and functional cellulose nanocrystals (CNC) and nanofibrils (CNF) by hydrolysis using concentrated organic acids. Due to their low water solubility, these solid organic acids can be easily recovered after hydrolysis reactions through crystallization at a lower or ambient temperature. When dicarboxylic acids were...

  8. Combining Stable Isotope Labeling and Molecular Networking for Biosynthetic Pathway Characterization

    DEFF Research Database (Denmark)

    Klitgaard, Andreas; Nielsen, Jakob Blæsbjerg; Frandsen, Rasmus John Normand

    2015-01-01

    Filamentous fungi are a rich source of bioactive compounds, ranging from statins over immunosuppressants to antibiotics. The coupling of genes to metabolites is of large commercial interest for production of the bioactives of the future. To this end, we have investigated the use of stable isotope...... of the peptide sequence, which could be used to provide information on biosynthesis of bioactive compounds....

  9. Stable aqueous dispersions of optically and electronically active phosphorene.

    Science.gov (United States)

    Kang, Joohoon; Wells, Spencer A; Wood, Joshua D; Lee, Jae-Hyeok; Liu, Xiaolong; Ryder, Christopher R; Zhu, Jian; Guest, Jeffrey R; Husko, Chad A; Hersam, Mark C

    2016-10-18

    Understanding and exploiting the remarkable optical and electronic properties of phosphorene require mass production methods that avoid chemical degradation. Although solution-based strategies have been developed for scalable exfoliation of black phosphorus, these techniques have thus far used anhydrous organic solvents in an effort to minimize exposure to known oxidants, but at the cost of limited exfoliation yield and flake size distribution. Here, we present an alternative phosphorene production method based on surfactant-assisted exfoliation and postprocessing of black phosphorus in deoxygenated water. From comprehensive microscopic and spectroscopic analysis, this approach is shown to yield phosphorene dispersions that are stable, highly concentrated, and comparable to micromechanically exfoliated phosphorene in structure and chemistry. Due to the high exfoliation efficiency of this process, the resulting phosphorene flakes are thinner than anhydrous organic solvent dispersions, thus allowing the observation of layer-dependent photoluminescence down to the monolayer limit. Furthermore, to demonstrate preservation of electronic properties following solution processing, the aqueous-exfoliated phosphorene flakes are used in field-effect transistors with high drive currents and current modulation ratios. Overall, this method enables the isolation and mass production of few-layer phosphorene, which will accelerate ongoing efforts to realize a diverse range of phosphorene-based applications.

  10. Discovery of microRNAs of the stable fly (Diptera: Muscidae) by High-throughput sequencing.

    Science.gov (United States)

    Tuckow, Alexander P; Temeyer, Kevin B; Olafson, Pia U; Pérez de Léon, Adalberto A

    2013-07-01

    The stable fly, Stomoxys calcitrans (L.), is a serious ectoparasite affecting animal production and health of both animals and humans. Stable fly control relies largely on chemical insecticides; however, the development of insecticide resistance as well as environmental considerations requires continued discovery research to develop novel control technologies. MicroRNAs (miRNAs) are a class of short noncoding RNAs that have been shown to be important regulators of gene expression across a wide variety of organisms, and may provide an innovative approach with regard to development of safer more targeted control technologies. The current study reports discovery ad initial comparative analysis of 88 presumptive miRNA sequences from the stable fly, obtained using high-throughput sequencing of small RNAs. The majority of stable fly miRNAs were 22-23 nt in length. Many miRNAs were arthropod specific, and several mature miRNA sequences showed greater sequence identity to miRNAs from other blood-feeding dipterans such as mosquitoes rather than to Drosophilids. This initial step in characterizing the stable fly microRNAome provides a basis for further analyses of life stage-specific and tissue-specific expression to elucidate their functional roles in stable fly biology.

  11. Multivariate Max-Stable Spatial Processes

    KAUST Repository

    Genton, Marc G.

    2014-01-06

    Analysis of spatial extremes is currently based on univariate processes. Max-stable processes allow the spatial dependence of extremes to be modelled and explicitly quantified, they are therefore widely adopted in applications. For a better understanding of extreme events of real processes, such as environmental phenomena, it may be useful to study several spatial variables simultaneously. To this end, we extend some theoretical results and applications of max-stable processes to the multivariate setting to analyze extreme events of several variables observed across space. In particular, we study the maxima of independent replicates of multivariate processes, both in the Gaussian and Student-t cases. Then, we define a Poisson process construction in the multivariate setting and introduce multivariate versions of the Smith Gaussian extremevalue, the Schlather extremal-Gaussian and extremal-t, and the BrownResnick models. Inferential aspects of those models based on composite likelihoods are developed. We present results of various Monte Carlo simulations and of an application to a dataset of summer daily temperature maxima and minima in Oklahoma, U.S.A., highlighting the utility of working with multivariate models in contrast to the univariate case. Based on joint work with Simone Padoan and Huiyan Sang.

  12. Application of stable isotope to breath test

    International Nuclear Information System (INIS)

    Sasaki, Yasuto

    1988-01-01

    Needles to say, radioisotopes have good characteristics as a tracer for examining biological functions. In fact, scyntigraphy is widely used over Japan. It is true, however, that there are some difficulties in applying radioisotopes to humans. Thus, greater attention began to be attracted to stable isotopes in the late 1960s, because these substances can be used for infants and pregnant women. They can be stored for a long period of time since they do not suffer damping as in the case of radioisotopes. In addition to serving as a tracer, stable isotopes can provide structural-chemical information including the position of isotope labels, and the mass and atomic composition of fragment ions. Such techniques as NMR spectroscopy is employed for this purpose. The method is currently used to perform examinations of congenital metabolic disorders. The carbon isotopes of 13 C and 14 C are used for breath test. Compounds labeled with these isotopes are administered and their ratio to the total CO 2 in breath is measured to diagnose diseases. In the early 1970s, 13 C has come into use for breath test. Similar breath test is applied to diagnosis of the bacterial overgrowth syndrome and ileal dysfunction syndrome. (Nogami, K.)

  13. Stable states in a strong IR field

    Science.gov (United States)

    Zhong, Changchun; Robicheaux, Francis

    2015-05-01

    It is found that 10% of atoms stay in the quasi-stable states after being exposed to intense laser or microwave (MW) pulses, even though the pulses' intensity is much stronger than that needed for static fields ionization. The reason why atoms survive those strong pulses has attracted growing attentions. A. Arakelyan et al. have observed the optical spectra of the surviving Lithium atoms after interaction with intense 38-GHz MW fields for more than 1000 cycles, and the spectra exhibit a periodic train of peaks 38 GHz apart. It suggests that those weakly bound Rydberg electrons seldom go back to the ionic core, where the cycle average energy exchange happens. In this study, we are interested in the electron behavior in the presence of intense infrared fields with a much shorter wavelength (1000 nm). By solving the full 3D time dependent Schrodinger equation, we calculate the spectra of the surviving atoms under intense IR fields. Our numerical calculations show atoms survive the intense field in quasi-stable states for a long time, and the optical spectra are obviously modulated by the IR frequency. Through tuning the ponderomotive energy, we see how field parameters affect the behavior of electrons. Different atoms, such as Hydrogen, Helium, Lithium, and Sodium, are tested to see how atom's energy structures influence the results.

  14. Color stable manganese-doped phosphors

    Science.gov (United States)

    Lyons, Robert Joseph [Burnt Hills, NY; Setlur, Anant Achyut [Niskayuna, NY; Deshpande, Anirudha Rajendra [Twinsburg, OH; Grigorov, Ljudmil Slavchev [Sofia, BG

    2012-08-28

    A process for preparing color stable Mn.sup.+4 doped phosphors includes providing a phosphor of formula I; A.sub.x[MF.sub.y]:Mn.sup.+4 I and contacting the phosphor in particulate form with a saturated solution of a composition of formula II in aqueous hydrofluoric acid; A.sub.x[MF.sub.y]; II wherein A is Li, Na, K, Rb, Cs, NR.sub.4 or a combination thereof; M is Si, Ge, Sn, Ti, Zr, Al, Ga, In, Sc, Y, La, Nb, Ta, Bi, Gd, or a combination thereof; R is H, lower alkyl, or a combination thereof; x is the absolute value of the charge of the [MF.sub.y] ion; and y is 5, 6 or 7. In particular embodiments, M is Si, Ge, Sn, Ti, Zr, or a combination thereof. A lighting apparatus capable of emitting white light includes a semiconductor light source; and a phosphor composition radiationally coupled to the light source, and which includes a color stable Mn.sup.+4 doped phosphor.

  15. Dietary Heterogeneity among Western Industrialized Countries Reflected in the Stable Isotope Ratios of Human Hair

    OpenAIRE

    Valenzuela, Luciano O.; Chesson, Lesley A.; Bowen, Gabriel J.; Cerling, Thure E.; Ehleringer, James R.

    2012-01-01

    Although the globalization of food production is often assumed to result in a homogenization of consumption patterns with a convergence towards a Western style diet, the resources used to make global food products may still be locally produced (glocalization). Stable isotope ratios of human hair can quantify the extent to which residents of industrialized nations have converged on a standardized diet or whether there is persistent heterogeneity and glocalization among countries as a result of...

  16. Stable producer cell lines for adeno-associated virus (AAV) assembly.

    Science.gov (United States)

    Chadeuf, Gilliane; Salvetti, Anna

    2010-10-01

    Stable producer cell lines containing both the rep and cap genes and recombinant adeno-associated virus (rAAV) vectors can be infected with a helper virus to provide reliable and efficient production of rAAV stocks. However, the development of these cell lines is time-consuming. The procedure described here is therefore recommended only for studies requiring the production of high amounts of rAAV, such as preclinical studies performed in large animals.

  17. Estimation of Time-Varying Autoregressive Symmetric Alpha Stable

    Data.gov (United States)

    National Aeronautics and Space Administration — In the last decade alpha-stable distributions have become a standard model for impulsive data. Especially the linear symmetric alpha-stable processes have found...

  18. A New Stable Isotope Record From the Subantarctic Southeastern Pacific

    Science.gov (United States)

    Waddell, L. M.; Hendy, I. L.; Moore, T. C.; Lyle, M. W.

    2007-12-01

    Few stable isotope records exist from the southeast Pacific Ocean due to its remote location, low sedimentation rates, and shallow carbonate compensation depth (CCD). The CCD in the southeast Pacific, however, has been found to be unusually deep (~4750 m), thereby allowing for the preservation of Neogene carbonates at abyssal depths. Herein we present stable isotope results from MV0502-4JC, which was recently recovered from the subantarctic region of the Southwest Pacific (50°20S, 148°08W, 4286 m). Dating the record with radiolarian biostratigraphy, we have generated a benthic stable isotope record back to the Middle Miocene from Cibicidoides spp. and a planktic record from Globigerina bulloides into the Late Pliocene. These stable isotope records, in conjunction with carbonate contents and counts of ice-rafted debris (IRD) and manganese micronodules show the effect of global ice sheet build up on this poorly understood region. A prominent negative δ13C shift of ~1‰ (from ~1 to ~0.2‰) in the benthic record occurs at ~15.3 MBSF (Middle Miocene) as carbonate contents in the core decrease from ~80% to ~20%, and significant changes in the bottom water are indicated by changes in the dominant Cibicidoides spp. at the site from C. robertsonianus to C. wuellerstorfi. Trace amounts of IRD and abundant manganese micronodules also appear at the site at this time. A significant hiatus (from the Late Miocene to the Middle Pliocene) occurs somewhere between 11.4 and 9.8 MBSF. From 9.8 to 8 MBSF (Late Pliocene) benthic δ18O increases and δ13C decreases by ~1‰. Also, IRD increases, manganese micronodules decrease, and there is a dramatic increase in the preservation of planktic foraminifera at the site. A planktic δ13C shift of >1‰ (from 0 to 1‰) occurs at ~5 MBSF (Pleistocene) coincident with a 20% increase in carbonate concentration. After this interval, the variability in both benthic δ18O and δ13C and planktic δ18O increases significantly. We interpret the

  19. Stable CSR in Storage Rings: A Model

    International Nuclear Information System (INIS)

    Sannibale, F.

    2005-01-01

    A comprehensive historical view of the work done on coherent synchrotron radiation (CSR) in storage rings is given in reference [1]. Here we want just to point out that even if the issue of CSR in storage rings was already discussed over 50 years ago, it is only recently that a considerable number of observations have been reported. In fact, intense bursts of coherent synchrotron radiation with a stochastic character were measured in the terahertz frequency range, at several synchrotron light source storage rings [2-8]. It has been shown [8-11], that this bursting emission of CSR is associated with a single bunch instability, usually referred as microbunching instability (MBI), driven by the fields of the synchrotron radiation emitted by the bunch itself. Of remarkably different characteristics was the CSR emission observed at BESSY II in Berlin, when the storage ring was tuned into a special low momentum compaction mode [12, 13]. In fact, the emitted radiation was not the quasi-random bursting observed in the other machines, but a powerful and stable flux of broadband CSR in the terahertz range. This was an important result, because it experimentally demonstrated the concrete possibility of constructing a stable broadband source with extremely high power in the terahertz region. Since the publication of the first successful experiment using the ring as a CSR source [14], BESSY II has regular scheduled user's shifts dedicated to CSR experiments. At the present time, several other laboratories are investigating the possibility of a CSR mode of operation [15-17] and a design for a new ring optimized for CSR is at an advanced stage [18]. In what follows, we describe a model that first accounts for the BESSY II observations and then indicates that the special case of BESSY II is actually quite general and typical when relativistic electron storage rings are tuned for short bunches. The model provides a scheme for predicting and optimizing the performance of ring

  20. Stable CSR in storage rings: A model

    International Nuclear Information System (INIS)

    Sannibale, Fernando; Byrd, John M.; Loftsdottir, Agusta; Venturini, Marco; Abo-Bakr, Michael; Feikes, Jorge; Holldack, Karsten; Kuske, Peter; Wustefeld, Godehart; Hubers, Heinz-Willerm; Warnock, Robert

    2005-01-01

    A comprehensive historical view of the work done on coherent synchrotron radiation (CSR) in storage rings is given in reference [1]. Here we want just to point out that even if the issue of CSR in storage rings was already discussed over 50 years ago, it is only recently that a considerable number of observations have been reported. In fact, intense bursts of coherent synchrotron radiation with a stochastic character were measured in the terahertz frequency range, at several synchrotron light source storage rings [2-8]. It has been shown [8-11], that this bursting emission of CSR is associated with a single bunch instability, usually referred as microbunching instability (MBI), driven by the fields of the synchrotron radiation emitted by the bunch itself. Of remarkably different characteristics was the CSR emission observed at BESSY II in Berlin, when the storage ring was tuned into a special low momentum compaction mode [12, 13]. In fact, the emitted radiation was not the quasi-random bursting observed in the other machines, but a powerful and stable flux of broadband CSR in the terahertz range. This was an important result, because it experimentally demonstrated the concrete possibility of constructing a stable broadband source with extremely high power in the terahertz region. Since the publication of the first successful experiment using the ring as a CSR source [14], BESSY II has regular scheduled user s shifts dedicated to CSR experiments. At the present time, several other laboratories are investigating the possibility of a CSR mode of operation [15-17] and a design for a new ring optimized for CSR is at an advanced stage [18]. In what follows, we describe a model that first accounts for the BESSY II observations and then indicates that the special case of BESSY II is actually quite general and typical when relativistic electron storage rings are tuned for short bunches. The model provides a scheme for predicting and optimizing the performance of ring