WorldWideScience

Sample records for stable process conditions

  1. Normal modified stable processes

    DEFF Research Database (Denmark)

    Barndorff-Nielsen, Ole Eiler; Shephard, N.

    2002-01-01

    Gaussian (NGIG) laws. The wider framework thus established provides, in particular, for added flexibility in the modelling of the dynamics of financial time series, of importance especially as regards OU based stochastic volatility models for equities. In the special case of the tempered stable OU process......This paper discusses two classes of distributions, and stochastic processes derived from them: modified stable (MS) laws and normal modified stable (NMS) laws. This extends corresponding results for the generalised inverse Gaussian (GIG) and generalised hyperbolic (GH) or normal generalised inverse...

  2. [Startup, stable operation and process failure of EBPR system under the low temperature and low dissolved oxygen condition].

    Science.gov (United States)

    Ma, Juan; Li, Lu; Yu, Xiao-Jun; Wei, Xue-Fen; Liu, Juan-Li

    2015-02-01

    A sequencing batch reactor (SBR) was started up and operated with alternating anaerobic/oxic (An/O) to perform enhanced biological phosphorus removal (EBPR) under the condition of 13-16 degrees C. The results showed that under the condition of low temperature, the EBPR system was successfully started up in a short time (<6 d). The reactor achieved a high and stable phosphorus removal performance with an influent phosphate concentration of 20 mg x L(-1) and the dissolved oxygen (DO) concentration of 2 mg x L(-1). The effluent phosphate concentration was lower than 0.5 mg x L(-1). It was found that decreasing DO had an influence on the steady operation of EBPR system. As DO concentration of aerobic phase decreased from 2 mg x L(-1) to 1 mg x L(-1), the system could still perform EBPR and the phosphorus removal efficiency was greater than 97.4%. However, the amount of phosphate released during anaerobic phase was observed to decrease slightly compared with that of 2 mg x L(-1) DO condition. Moreover, the phosphorus removal performance of the system deteriorated immediately and the effluent phosphate concentration couldn't meet the national integrated wastewater discharge standard when DO concentration was further lowered to 0.5 mg x L(-1). The experiments of increasing DO to recover phosphorus removal performance of the EBPR suggested the process failure resulted from low DO was not reversible in the short-term. It was also found that the batch tests of anoxic phosphorus uptake using nitrite and nitrate as electron acceptors had an impact on the stable operation of EBPR system, whereas the resulting negative influence could be recovered within 6 cycles. In addition, the mixed liquid suspended solids (MLSS) of the EBPR system remained stable and the sludge volume index (SVI) decreased to a certain extend in a long run, implying long-term low temperature and low DO condition favored the sludge sedimentation.

  3. A highly stable minimally processed plant-derived recombinant acetylcholinesterase for nerve agent detection in adverse conditions.

    Science.gov (United States)

    Rosenberg, Yvonne J; Walker, Jeremy; Jiang, Xiaoming; Donahue, Scott; Robosky, Jason; Sack, Markus; Lees, Jonathan; Urban, Lori

    2015-08-13

    Although recent innovations in transient plant systems have enabled gram quantities of proteins in 1-2 weeks, very few have been translated into applications due to technical challenges and high downstream processing costs. Here we report high-level production, using a Nicotiana benthamiana/p19 system, of an engineered recombinant human acetylcholinesterase (rAChE) that is highly stable in a minimally processed leaf extract. Lyophylized clarified extracts withstand prolonged storage at 70 °C and, upon reconstitution, can be used in several devices to detect organophosphate (OP) nerve agents and pesticides on surfaces ranging from 0 °C to 50 °C. The recent use of sarin in Syria highlights the urgent need for nerve agent detection and countermeasures necessary for preparedness and emergency responses. Bypassing cumbersome and expensive downstream processes has enabled us to fully exploit the speed, low cost and scalability of transient production systems resulting in the first successful implementation of plant-produced rAChE into a commercial biotechnology product.

  4. Working conditions remain stable in the Netherlands

    NARCIS (Netherlands)

    Houtman, I.; Hooftman, W.

    2008-01-01

    Despite significant changes in the national questionnaires on work and health, the quality of work as well as health complaints in the Netherlands appear to be relatively stable. Pace of work seems to be on the increase again and more people are working in excess of their contractual hours.

  5. Exact simulation of max-stable processes.

    Science.gov (United States)

    Dombry, Clément; Engelke, Sebastian; Oesting, Marco

    2016-06-01

    Max-stable processes play an important role as models for spatial extreme events. Their complex structure as the pointwise maximum over an infinite number of random functions makes their simulation difficult. Algorithms based on finite approximations are often inexact and computationally inefficient. We present a new algorithm for exact simulation of a max-stable process at a finite number of locations. It relies on the idea of simulating only the extremal functions, that is, those functions in the construction of a max-stable process that effectively contribute to the pointwise maximum. We further generalize the algorithm by Dieker & Mikosch (2015) for Brown-Resnick processes and use it for exact simulation via the spectral measure. We study the complexity of both algorithms, prove that our new approach via extremal functions is always more efficient, and provide closed-form expressions for their implementation that cover most popular models for max-stable processes and multivariate extreme value distributions. For simulation on dense grids, an adaptive design of the extremal function algorithm is proposed.

  6. Multivariate Max-Stable Spatial Processes

    KAUST Repository

    Genton, Marc G.

    2014-01-06

    Analysis of spatial extremes is currently based on univariate processes. Max-stable processes allow the spatial dependence of extremes to be modelled and explicitly quantified, they are therefore widely adopted in applications. For a better understanding of extreme events of real processes, such as environmental phenomena, it may be useful to study several spatial variables simultaneously. To this end, we extend some theoretical results and applications of max-stable processes to the multivariate setting to analyze extreme events of several variables observed across space. In particular, we study the maxima of independent replicates of multivariate processes, both in the Gaussian and Student-t cases. Then, we define a Poisson process construction in the multivariate setting and introduce multivariate versions of the Smith Gaussian extremevalue, the Schlather extremal-Gaussian and extremal-t, and the BrownResnick models. Inferential aspects of those models based on composite likelihoods are developed. We present results of various Monte Carlo simulations and of an application to a dataset of summer daily temperature maxima and minima in Oklahoma, U.S.A., highlighting the utility of working with multivariate models in contrast to the univariate case. Based on joint work with Simone Padoan and Huiyan Sang.

  7. Multivariate Max-Stable Spatial Processes

    KAUST Repository

    Genton, Marc G.

    2014-01-01

    Analysis of spatial extremes is currently based on univariate processes. Max-stable processes allow the spatial dependence of extremes to be modelled and explicitly quantified, they are therefore widely adopted in applications. For a better understanding of extreme events of real processes, such as environmental phenomena, it may be useful to study several spatial variables simultaneously. To this end, we extend some theoretical results and applications of max-stable processes to the multivariate setting to analyze extreme events of several variables observed across space. In particular, we study the maxima of independent replicates of multivariate processes, both in the Gaussian and Student-t cases. Then, we define a Poisson process construction in the multivariate setting and introduce multivariate versions of the Smith Gaussian extremevalue, the Schlather extremal-Gaussian and extremal-t, and the BrownResnick models. Inferential aspects of those models based on composite likelihoods are developed. We present results of various Monte Carlo simulations and of an application to a dataset of summer daily temperature maxima and minima in Oklahoma, U.S.A., highlighting the utility of working with multivariate models in contrast to the univariate case. Based on joint work with Simone Padoan and Huiyan Sang.

  8. Qualification of conditioning process

    International Nuclear Information System (INIS)

    Wolf, J.

    1989-01-01

    A conditioning process is qualified by the PTB if the execution of pre-treatment and conditioning occurs so that a safe and orderly final storage of the products and waste containers produced can be assumed. All the relevant operating conditions for the plant are laid down by the producer/conditioner of the waste in a handbook. The elements of product inspection by process qualification are shown in tabular form. (DG) [de

  9. Multivariate max-stable spatial processes

    KAUST Repository

    Genton, Marc G.; Padoan, S. A.; Sang, H.

    2015-01-01

    Max-stable processes allow the spatial dependence of extremes to be modelled and quantified, so they are widely adopted in applications. For a better understanding of extremes, it may be useful to study several variables simultaneously. To this end, we study the maxima of independent replicates of multivariate processes, both in the Gaussian and Student-t cases. We define a Poisson process construction and introduce multivariate versions of the Smith Gaussian extreme-value, the Schlather extremal-Gaussian and extremal-t, and the Brown–Resnick models. We develop inference for the models based on composite likelihoods. We present results of Monte Carlo simulations and an application to daily maximum wind speed and wind gust.

  10. Multivariate max-stable spatial processes

    KAUST Repository

    Genton, Marc G.

    2015-02-11

    Max-stable processes allow the spatial dependence of extremes to be modelled and quantified, so they are widely adopted in applications. For a better understanding of extremes, it may be useful to study several variables simultaneously. To this end, we study the maxima of independent replicates of multivariate processes, both in the Gaussian and Student-t cases. We define a Poisson process construction and introduce multivariate versions of the Smith Gaussian extreme-value, the Schlather extremal-Gaussian and extremal-t, and the Brown–Resnick models. We develop inference for the models based on composite likelihoods. We present results of Monte Carlo simulations and an application to daily maximum wind speed and wind gust.

  11. Reactive gas control of non-stable plasma conditions

    International Nuclear Information System (INIS)

    Bellido-Gonzalez, V.; Daniel, B.; Counsell, J.; Monaghan, D.

    2006-01-01

    Most industrial plasma processes are dependant upon the control of plasma properties for repeatable and reliable production. The speed of production and range of properties achieved depend on the degree of control. Process control involves all the aspects of the vacuum equipment, substrate preparation, plasma source condition, power supplies, process drift, valves (inputs/outputs), signal and data processing and the user's understanding and ability. In many cases, some of the processes which involve the manufacturing of interesting coating structures, require a precise control of the process in a reactive environment [S.J. Nadel, P. Greene, 'High rate sputtering technology for throughput and quality', International Glass Review, Issue 3, 2001, p. 45. ]. Commonly in these circumstances the plasma is not stable if all the inputs and outputs of the system were to remain constant. The ideal situation is to move a process from set-point A to B in zero time and maintain the monitored signal with a fluctuation equal to zero. In a 'real' process that's not possible but improvements in the time response and energy delivery could be achieved with an appropriate algorithm structure. In this paper an advanced multichannel reactive plasma gas control system is presented. The new controller offers both high-speed gas control combined with a very flexible control structure. The controller uses plasma emission monitoring, target voltage or any process sensor monitoring as the input into a high-speed control algorithm for gas input. The control algorithm and parameters can be tuned to different process requirements in order to optimize response times

  12. Biosensors engineered from conditionally stable ligand-binding domains

    Science.gov (United States)

    Church, George M.; Feng, Justin; Mandell, Daniel J.; Baker, David; Fields, Stanley; Jester, Benjamin Ward; Tinberg, Christine Elaine

    2017-09-19

    Disclosed is a biosensor engineered to conditionally respond to the presence of specific small molecules, the biosensors including conditionally stable ligand-binding domains (LBDs) which respond to the presence of specific small molecules, wherein readout of binding is provided by reporter genes or transcription factors (TFs) fused to the LBDs.

  13. Stochastic conditional intensity processes

    DEFF Research Database (Denmark)

    Bauwens, Luc; Hautsch, Nikolaus

    2006-01-01

    model allows for a wide range of (cross-)autocorrelation structures in multivariate point processes. The model is estimated by simulated maximum likelihood (SML) using the efficient importance sampling (EIS) technique. By modeling price intensities based on NYSE trading, we provide significant evidence......In this article, we introduce the so-called stochastic conditional intensity (SCI) model by extending Russell’s (1999) autoregressive conditional intensity (ACI) model by a latent common dynamic factor that jointly drives the individual intensity components. We show by simulations that the proposed...... for a joint latent factor and show that its inclusion allows for an improved and more parsimonious specification of the multivariate intensity process...

  14. A Note on Interpolation of Stable Processes | Nassiuma | Journal of ...

    African Journals Online (AJOL)

    Interpolation procedures tailored for gaussian processes may not be applied to infinite variance stable processes. Alternative techniques suitable for a limited set of stable case with index α∈(1,2] were initially studied by Pourahmadi (1984) for harmonizable processes. This was later extended to the ARMA stable process ...

  15. Tukey max-stable processes for spatial extremes

    KAUST Repository

    Xu, Ganggang; Genton, Marc G.

    2016-01-01

    We propose a new type of max-stable process that we call the Tukey max-stable process for spatial extremes. It brings additional flexibility to modeling dependence structures among spatial extremes. The statistical properties of the Tukey max

  16. On the Hitting Probability of Max-Stable Processes

    OpenAIRE

    Hofmann, Martin

    2012-01-01

    The probability that a max-stable process {\\eta} in C[0, 1] with identical marginal distribution function F hits x \\in R with 0 < F (x) < 1 is the hitting probability of x. We show that the hitting probability is always positive, unless the components of {\\eta} are completely dependent. Moreover, we consider the event that the paths of standard MSP hit some x \\in R twice and we give a sufficient condition for a positive probability of this event.

  17. Tukey max-stable processes for spatial extremes

    KAUST Repository

    Xu, Ganggang

    2016-09-21

    We propose a new type of max-stable process that we call the Tukey max-stable process for spatial extremes. It brings additional flexibility to modeling dependence structures among spatial extremes. The statistical properties of the Tukey max-stable process are demonstrated theoretically and numerically. Simulation studies and an application to Swiss rainfall data indicate the effectiveness of the proposed process. © 2016 Elsevier B.V.

  18. Shelf-stable foods through irradiation processing

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    This survey has been produced from a database on analytical reference materials of biological and environmental origin, which is maintained at the International Atomic Energy Agency. It is an updated version of earlier reports, the last published in 1990. The information presented refers mostly to reference materials for trace element constituents; however, information is also included on a number of other selected measurands of relevance to IAEA programmes, i.e. radionuclides, stable isotopes, anions, cations, organometallic compounds and organic contaminants. The database presently contains over 10,000 analyte values for 455 measurands in 650 reference materials produced by 30 different suppliers. Additional information on the cost of the materials, the unit size supplied, and recommended minimum weight of material for analysis is also provided, if this information is available to the authors. It is expected that this survey will help analysts to select reference materials for quality assurance purposes that match as closely as possible, with respect to matrix type and concentrations of the measurands of interest, their samples to be analyzed. 22 refs, 2 tabs.

  19. Shelf-stable foods through irradiation processing

    International Nuclear Information System (INIS)

    1995-11-01

    This survey has been produced from a database on analytical reference materials of biological and environmental origin, which is maintained at the International Atomic Energy Agency. It is an updated version of earlier reports, the last published in 1990. The information presented refers mostly to reference materials for trace element constituents; however, information is also included on a number of other selected measurands of relevance to IAEA programmes, i.e. radionuclides, stable isotopes, anions, cations, organometallic compounds and organic contaminants. The database presently contains over 10,000 analyte values for 455 measurands in 650 reference materials produced by 30 different suppliers. Additional information on the cost of the materials, the unit size supplied, and recommended minimum weight of material for analysis is also provided, if this information is available to the authors. It is expected that this survey will help analysts to select reference materials for quality assurance purposes that match as closely as possible, with respect to matrix type and concentrations of the measurands of interest, their samples to be analyzed. 22 refs, 2 tabs

  20. Tempered stable distributions stochastic models for multiscale processes

    CERN Document Server

    Grabchak, Michael

    2015-01-01

    This brief is concerned with tempered stable distributions and their associated Levy processes. It is a good text for researchers interested in learning about tempered stable distributions.  A tempered stable distribution is one which takes a stable distribution and modifies its tails to make them lighter. The motivation for this class comes from the fact that infinite variance stable distributions appear to provide a good fit to data in a variety of situations, but the extremely heavy tails of these models are not realistic for most real world applications. The idea of using distributions that modify the tails of stable models to make them lighter seems to have originated in the influential paper of Mantegna and Stanley (1994). Since then, these distributions have been extended and generalized in a variety of ways. They have been applied to a wide variety of areas including mathematical finance, biostatistics,computer science, and physics.

  1. Incineration ash conditioning processes

    International Nuclear Information System (INIS)

    Jouan, A.; Ouvrier, N.; Teulon, F.

    1990-01-01

    Incinerable wastes consist of the following standard composition corresponding to projected wastes from a future mixed oxide fuel fabrication plant with an annual throughput of 1700 kg (i.e. 5.7 m 3 ) of ashes produced by the incineration facility: . 50% polyvinyl chloride (glove box sleeves), . 5% polyethylene (bags), . 35% rubber (equal amounts of latex and neoprene), . 10% cellulose (equal amounts of cotton and cleansing tissues). The work focused mainly on compaction by high-temperature isostatic pressing, is described in some detail with the results obtained. An engineering study was also carried out to compare this technology with two other ash containment processes: direct-induction (cold crucible) melting and cement-resin matrix embedding. Induction melting is considerably less costly than isostatic pressing; the operating costs are about 1.5 times higher than for cement-resin embedding, but the volume reduction is nearly 3 times greater

  2. The Fractional Poisson Process and the Inverse Stable Subordinator

    OpenAIRE

    Meerschaert, Mark; Nane, Erkan; Vellaisamy, P.

    2011-01-01

    The fractional Poisson process is a renewal process with Mittag-Leffler waiting times. Its distributions solve a time-fractional analogue of the Kolmogorov forward equation for a Poisson process. This paper shows that a traditional Poisson process, with the time variable replaced by an independent inverse stable subordinator, is also a fractional Poisson process. This result unifies the two main approaches in the stochastic theory of time-fractional diffusion equations. The equivalence extend...

  3. Conditions for maximum isolation of stable condensate during separation in gas-condensate systems

    Energy Technology Data Exchange (ETDEWEB)

    Trivus, N.A.; Belkina, N.A.

    1969-02-01

    A thermodynamic analysis is made of the gas-liquid separation process in order to determine the relationship between conditions of maximum stable condensate separation and physico-chemical nature and composition of condensate. The analysis was made by considering the multicomponent gas-condensate fluid produced from Zyrya field as a ternary system, composed of methane, an intermediate component (propane and butane) and a heavy residue, C/sub 6+/. Composition of 5 ternary systems was calculated for a wide variation in separator conditions. At each separator pressure there is maximum condensate production at a certain temperature. This occurs because solubility of condensate components changes with temperature. Results of all calculations are shown graphically. The graphs show conditions of maximum stable condensate separation.

  4. Conditioning processes for incinerator ashes

    International Nuclear Information System (INIS)

    Jouan, A.; Ouvrier, N.; Teulon, F.

    1990-01-01

    Three conditioning processes for alpha-bearing solid waste incineration ashes were investigated and compared according to technical and economic criteria: isostatic pressing, cold-crucible direct-induction melting and cement-resin matrix embedding

  5. On the joint statistics of stable random processes

    International Nuclear Information System (INIS)

    Hopcraft, K I; Jakeman, E

    2011-01-01

    A utilitarian continuous bi-variate random process whose first-order probability density function is a stable random variable is constructed. Results paralleling some of those familiar from the theory of Gaussian noise are derived. In addition to the joint-probability density for the process, these include fractional moments and structure functions. Although the correlation functions for stable processes other than Gaussian do not exist, we show that there is coherence between values adopted by the process at different times, which identifies a characteristic evolution with time. The distribution of the derivative of the process, and the joint-density function of the value of the process and its derivative measured at the same time are evaluated. These enable properties to be calculated analytically such as level crossing statistics and those related to the random telegraph wave. When the stable process is fractal, the proportion of time it spends at zero is finite and some properties of this quantity are evaluated, an optical interpretation for which is provided. (paper)

  6. The tempered stable process with infinitely divisible inverse subordinators

    International Nuclear Information System (INIS)

    Wyłomańska, Agnieszka

    2013-01-01

    In the last decade processes driven by inverse subordinators have become extremely popular. They have been used in many different applications, especially for data with observable constant time periods. However, the classical model, i.e. the subordinated Brownian motion, can be inappropriate for the description of observed phenomena that exhibit behavior not adequate for Gaussian systems. Therefore, in this paper we extend the classical approach and replace the Brownian motion by the tempered stable process. Moreover, on the other hand, as an extension of the classical model, we analyze the general class of inverse subordinators. We examine the main properties of the tempered stable process driven by inverse subordinators from the infinitely divisible class of distributions. We show the fractional Fokker–Planck equation of the examined process and the asymptotic behavior of the mean square displacement for two cases of subordinators. Additionally, we examine how an external force can influence the examined characteristics. (paper)

  7. On the Fractional Poisson Process and the Discretized Stable Subordinator

    Directory of Open Access Journals (Sweden)

    Rudolf Gorenflo

    2015-08-01

    Full Text Available We consider the renewal counting number process N = N(t as a forward march over the non-negative integers with independent identically distributed waiting times. We embed the values of the counting numbers N in a “pseudo-spatial” non-negative half-line x ≥ 0 and observe that for physical time likewise we have t ≥ 0. Thus we apply the Laplace transform with respect to both variables x and t. Applying then a modification of the Montroll-Weiss-Cox formalism of continuous time random walk we obtain the essential characteristics of a renewal process in the transform domain and, if we are lucky, also in the physical domain. The process t = t(N of accumulation of waiting times is inverse to the counting number process, in honour of the Danish mathematician and telecommunication engineer A.K. Erlang we call it the Erlang process. It yields the probability of exactly n renewal events in the interval (0; t]. We apply our Laplace-Laplace formalism to the fractional Poisson process whose waiting times are of Mittag-Leffler type and to a renewal process whose waiting times are of Wright type. The process of Mittag-Leffler type includes as a limiting case the classical Poisson process, the process of Wright type represents the discretized stable subordinator and a re-scaled version of it was used in our method of parametric subordination of time-space fractional diffusion processes. Properly rescaling the counting number process N(t and the Erlang process t(N yields as diffusion limits the inverse stable and the stable subordinator, respectively.

  8. Reflow process stabilization by chemical characteristics and process conditions

    Science.gov (United States)

    Kim, Myoung-Soo; Park, Jeong-Hyun; Kim, Hak-Joon; Kim, Il-Hyung; Jeon, Jae-Ha; Gil, Myung-Goon; Kim, Bong-Ho

    2002-07-01

    With the shrunken device rule below 130nm, the patterning of smaller contact hole with enough process margin is required for mass production. Therefore, shrinking technology using thermal reflow process has been applied for smaller contact hole formation. In this paper, we have investigated the effects of chemical characteristics such as molecular weight, blocking ratio of resin, cross-linker amount and solvent type with its composition to reflow process of resist and found the optimized chemical composition for reflow process applicable condition. And several process conditions like resist coating thickness and multi-step thermal reflow method have been also evaluated to stabilize the pattern profile and improve CD uniformity after reflow process. From the experiment results, it was confirmed that the effect of crosslinker in resist to reflow properties such as reflow temperature and reflow rate were very critical and it controlled the pattern profile during reflow processing. And also, it showed stable CD uniformity and improved resist properties for top loss, film shrinkage and etch selectivity. The application of lower coating thickness of resist induced symmetric pattern profile even at edge with wider process margin. The introduction of two-step baking method for reflow process showed uniform CD value, also. It is believed that the application of resist containing crosslinker and optimized process conditions for smaller contact hole patterning is necessary for the mass production with a design rule below 130nm.

  9. On the likelihood function of Gaussian max-stable processes

    KAUST Repository

    Genton, M. G.; Ma, Y.; Sang, H.

    2011-01-01

    We derive a closed form expression for the likelihood function of a Gaussian max-stable process indexed by ℝd at p≤d+1 sites, d≥1. We demonstrate the gain in efficiency in the maximum composite likelihood estimators of the covariance matrix from p=2 to p=3 sites in ℝ2 by means of a Monte Carlo simulation study. © 2011 Biometrika Trust.

  10. On the likelihood function of Gaussian max-stable processes

    KAUST Repository

    Genton, M. G.

    2011-05-24

    We derive a closed form expression for the likelihood function of a Gaussian max-stable process indexed by ℝd at p≤d+1 sites, d≥1. We demonstrate the gain in efficiency in the maximum composite likelihood estimators of the covariance matrix from p=2 to p=3 sites in ℝ2 by means of a Monte Carlo simulation study. © 2011 Biometrika Trust.

  11. Representation and properties of a class of conditionally Gaussian processes

    DEFF Research Database (Denmark)

    Barndorff-Nielsen, Ole Eiler; Pedersen, Jan

    2009-01-01

    It is shown that the class of conditionally Gaussian processes with independent increments is stable under marginalisation and conditioning. Moreover, in general such processes can be represented as integrals of a time changed Brownian motion where the time change and the integrand are jointly in...

  12. Polyelectrolyte brushes: a novel stable lubrication system in aqueous conditions.

    Science.gov (United States)

    Kobayashi, Motoyasu; Terada, Masami; Takahara, Atsushi

    2012-01-01

    Surface-initiated controlled radical copolymerizations of 2-dimethylaminoethyl methacrylate (DMAEMA), 2-(methacryloyloxy)ethyl phosphorylcholine (MPC), 2-(methacryloyloxy)ethyltrimethylammonium chloride) (MTAC), and 3-sulfopropyl methacrylate potassium salt (SPMK) were carried out on a silicon wafer and glass ball to prepare polyelectrolyte brushes with excellent water wettability. The frictional coefficient of the polymer brushes was recorded on a ball-on-plate type tribometer by linear reciprocating motion of the brush specimen at a selected velocity of 1.5 x 10(-3) m s-1 under a normal load of 0.49 N applied to the stationary glass ball (d = 10 mm) at 298 K. The poly(DMAEMA-co-MPC) brush partially cross-linked by bis(2-iodoethoxy)ethane maintained a relatively low friction coefficient around 0.13 under humid air (RH > 75%) even after 200 friction cycles. The poly(SPMK) brush revealed an extremely low friction coefficient around 0.01 even after 450 friction cycles. We supposed that the abrasion of the brush was prevented owing to the good affinity of the poly(SPMK) brush for water forming a water lubrication layer, and electrostatic repulsive interactions among the brushes bearing sulfonic acid groups. Furthermore, the poly(SPMK-co-MTAC) brush with a chemically cross-linked structure showed a stable low friction coefficient in water even after 1400 friction cycles under a normal load of 139 MPa, indicating that the cross-linking structure improved the wear resistance of the brush layer.

  13. Stable pelagic vertebrate community structure through extreme Paleogene greenhouse conditions

    Science.gov (United States)

    Sibert, E. C.; Friedman, M.; Hull, P. M.; Hunt, G.; Norris, R. D.

    2016-02-01

    The species composition (structure) and energy transfer (function) of an ecosystem is reflected by the presence and type of consumers that it supports. Here we use ichthyoliths, microfossil fish teeth and shark denticles, to assess the ecological variability of the pelagic fish community structure and composition from the Late Cretaceous to the middle Eocene from a drill core in the South Pacific gyre (DSDP Site 596). We find that the overall vertebrate community structure, as measured by the relative abundance of sharks to ray-finned fishes, has a punctuated change at the Cretaceous/Paleogene mass extinction. The vertebrate community structure remained stable throughout the Paleogene despite a five-fold increase in overall abundance of ichthyoliths during the extreme greenhouse of the Early Eocene. Further, we use a novel system to quantify the morphological variation in fish teeth. We find that the morphospace occupied by the tooth assemblage is conserved throughout the interval, with a slight expansion following the Cretaceous-Paleogene mass extinction, and the evolution of a distinct morphotype-group around the Paleocene-Eocene boundary. While there are elevated rates of morphotype origination and extinction following the Cretaceous-Paleogene mass extinction, the extreme greenhouse warming of the Early Eocene and associated increase in fish production produce near-zero origination and extinction rates. The relative stability in composition of the pelagic vertebrate community during intervals of extreme climate change and across large ranges of total fish accumulation, suggests that pelagic ecosystem structure is robust to climate events, and that the overall structure of the pelagic fish community may be decoupled from both climate and ecosystem function.

  14. On Stable Wall Boundary Conditions for the Hermite Discretization of the Linearised Boltzmann Equation

    Science.gov (United States)

    Sarna, Neeraj; Torrilhon, Manuel

    2018-01-01

    We define certain criteria, using the characteristic decomposition of the boundary conditions and energy estimates, which a set of stable boundary conditions for a linear initial boundary value problem, involving a symmetric hyperbolic system, must satisfy. We first use these stability criteria to show the instability of the Maxwell boundary conditions proposed by Grad (Commun Pure Appl Math 2(4):331-407, 1949). We then recognise a special block structure of the moment equations which arises due to the recursion relations and the orthogonality of the Hermite polynomials; the block structure will help us in formulating stable boundary conditions for an arbitrary order Hermite discretization of the Boltzmann equation. The formulation of stable boundary conditions relies upon an Onsager matrix which will be constructed such that the newly proposed boundary conditions stay close to the Maxwell boundary conditions at least in the lower order moments.

  15. Production of stable isotopes utilizing the plasma separation process

    Science.gov (United States)

    Bigelow, T. S.; Tarallo, F. J.; Stevenson, N. R.

    2005-12-01

    A plasma separation process (PSP) is being operated at Theragenics Corporation's®, Oak Ridge, TN, facility for the enrichment of stable isotopes. The PSP utilizes ion cyclotron mass discrimination to separate isotopes on a relatively large scale. With a few exceptions, nearly any metallic element could be processed with PSP. Output isotope enrichment factor depends on natural abundance and mass separation and can be fairly high in some cases. The Theragenics™ PSP facility is believed to be the only such process currently in operation. This system was developed and formerly operated under the US Department of Energy Advanced Isotope Separation program. Theragenics™ also has a laboratory at the PSP site capable of harvesting the isotopes from the process and a mass spectrometer system for analyzing enrichment and product purity. Since becoming operational in 2002, Theragenics™ has utilized the PSP to separate isotopes of several elements including: dysprosium, erbium, gadolinium, molybdenum and nickel. Currently, Theragenics™ is using the PSP for the separation of 102Pd, which is used as precursor for the production of 103Pd. The 103Pd radioisotope is the active ingredient in TheraSeed®, which is used in the treatment of early stage prostate cancer and being investigated for other medical applications. New industrial, medical and research applications are being investigated for isotopes that can be enriched on the PSP. Pre-enrichment of accelerator or reactor targets offers improved radioisotope production. Theragenics operates 14 cyclotrons for proton activation and has access to HFIR at ORNL for neutron activation of radioisotopes.

  16. Evaluating the consequences of salmon nutrients for riparian organisms: Linking condition metrics to stable isotopes.

    Science.gov (United States)

    Vizza, Carmella; Sanderson, Beth L; Coe, Holly J; Chaloner, Dominic T

    2017-03-01

    Stable isotope ratios (δ 13 C and δ 15 N) have been used extensively to trace nutrients from Pacific salmon, but salmon transfer more than carbon and nitrogen to stream ecosystems, such as phosphorus, minerals, proteins, and lipids. To examine the importance of these nutrients, metrics other than isotopes need to be considered, particularly when so few studies have made direct links between these nutrients and how they affect riparian organisms. Our study specifically examined δ 13 C and δ 15 N of riparian organisms from salmon and non-salmon streams in Idaho, USA, at different distances from the streams, and examined whether the quality of riparian plants and the body condition of invertebrates varied with access to these nutrients. Overall, quality and condition metrics did not mirror stable isotope patterns. Most notably, all riparian organisms exhibited elevated δ 15 N in salmon streams, but also with proximity to both stream types suggesting that both salmon and landscape factors may affect δ 15 N. The amount of nitrogen incorporated from Pacific salmon was low for all organisms (1950s. In addition, our results support those of other studies that have cautioned that inferences from natural abundance isotope data, particularly in conjunction with mixing models for salmon-derived nutrient percentage estimates, may be confounded by biogeochemical transformations of nitrogen, physiological processes, and even historical legacies of nitrogen sources. Critically, studies should move beyond simply describing isotopic patterns to focusing on the consequences of salmon-derived nutrients by quantifying the condition and fitness of organisms putatively using those resources.

  17. Bayesian Modeling of Air Pollution Extremes Using Nested Multivariate Max-Stable Processes

    KAUST Repository

    Vettori, Sabrina; Huser, Raphaë l; Genton, Marc G.

    2018-01-01

    Capturing the potentially strong dependence among the peak concentrations of multiple air pollutants across a spatial region is crucial for assessing the related public health risks. In order to investigate the multivariate spatial dependence properties of air pollution extremes, we introduce a new class of multivariate max-stable processes. Our proposed model admits a hierarchical tree-based formulation, in which the data are conditionally independent given some latent nested $\\alpha$-stable random factors. The hierarchical structure facilitates Bayesian inference and offers a convenient and interpretable characterization. We fit this nested multivariate max-stable model to the maxima of air pollution concentrations and temperatures recorded at a number of sites in the Los Angeles area, showing that the proposed model succeeds in capturing their complex tail dependence structure.

  18. Bayesian Modeling of Air Pollution Extremes Using Nested Multivariate Max-Stable Processes

    KAUST Repository

    Vettori, Sabrina

    2018-03-18

    Capturing the potentially strong dependence among the peak concentrations of multiple air pollutants across a spatial region is crucial for assessing the related public health risks. In order to investigate the multivariate spatial dependence properties of air pollution extremes, we introduce a new class of multivariate max-stable processes. Our proposed model admits a hierarchical tree-based formulation, in which the data are conditionally independent given some latent nested $\\\\alpha$-stable random factors. The hierarchical structure facilitates Bayesian inference and offers a convenient and interpretable characterization. We fit this nested multivariate max-stable model to the maxima of air pollution concentrations and temperatures recorded at a number of sites in the Los Angeles area, showing that the proposed model succeeds in capturing their complex tail dependence structure.

  19. Conditions for Stable Chip Breaking and Provision of Machined Surface Quality While Turning with Asymmetric Tool Vibrations

    OpenAIRE

    Шелег, В. К.; Молочко, В. И.; Данильчик, С. С.

    2015-01-01

    The paper considers a process of turning structural steel with asymmetric tool vibrations directed along feeding. Asymmetric vibrations characterized by asymmetry coefficient of vibration cycle, their frequency and amplitude are additionally transferred to the tool in the turning process with the purpose to crush chips. Conditions of stable chip breaking and obtaining optimum dimensions of chip elements have been determined in the paper. In order to reduce a negative impact of the vibration a...

  20. Force production during squats performed with a rotational resistance device under stable versus unstable conditions.

    Science.gov (United States)

    Moras, Gerard; Vázquez-Guerrero, Jairo

    2015-11-01

    [Purpose] Force production during a squat action on a rotational resistance device (RRD) under stable and unstable conditions. [Subjects and Methods] Twenty-one healthy males were asked to perform six sets of six repetitions of squats on an RRD on either stable or unstable surfaces. The stable and unstable sets were performed on different days. Muscular outputs were obtained from a linear encoder and a strain gauge fixed to a vest. [Results] Overall, the results showed no significant differences for any of the dependent variables across exercise modes. Forcemean outputs were higher in the concentric phase than in the eccentric phase for each condition, but there were no differences in velocity, time or displacement. The forcepeak was similar in the eccentric and concentric phases of movement under both stable and unstable conditions. There were no significant differences in forcemean between sets per condition or between conditions. [Conclusion] These results suggest that performing squats with a RRD achieves similar forcemean and forcepeak under stable and unstable conditions. The forcepeak produced is also similar in concentric and eccentric phases.

  1. Conditioned sounds enhance visual processing.

    Directory of Open Access Journals (Sweden)

    Fabrizio Leo

    Full Text Available This psychophysics study investigated whether prior auditory conditioning influences how a sound interacts with visual perception. In the conditioning phase, subjects were presented with three pure tones ( =  conditioned stimuli, CS that were paired with positive, negative or neutral unconditioned stimuli. As unconditioned reinforcers we employed pictures (highly pleasant, unpleasant and neutral or monetary outcomes (+50 euro cents, -50 cents, 0 cents. In the subsequent visual selective attention paradigm, subjects were presented with near-threshold Gabors displayed in their left or right hemifield. Critically, the Gabors were presented in synchrony with one of the conditioned sounds. Subjects discriminated whether the Gabors were presented in their left or right hemifields. Participants determined the location more accurately when the Gabors were presented in synchrony with positive relative to neutral sounds irrespective of reinforcer type. Thus, previously rewarded relative to neutral sounds increased the bottom-up salience of the visual Gabors. Our results are the first demonstration that prior auditory conditioning is a potent mechanism to modulate the effect of sounds on visual perception.

  2. A stable penalty method for the compressible Navier-Stokes equations: I. Open boundary conditions

    DEFF Research Database (Denmark)

    Hesthaven, Jan; Gottlieb, D.

    1996-01-01

    The purpose of this paper is to present asymptotically stable open boundary conditions for the numerical approximation of the compressible Navier-Stokes equations in three spatial dimensions. The treatment uses the conservation form of the Navier-Stokes equations and utilizes linearization...

  3. Entropy Stable Wall Boundary Conditions for the Three-Dimensional Compressible Navier-Stokes Equations

    Science.gov (United States)

    Parsani, Matteo; Carpenter, Mark H.; Nielsen, Eric J.

    2015-01-01

    Non-linear entropy stability and a summation-by-parts framework are used to derive entropy stable wall boundary conditions for the three-dimensional compressible Navier-Stokes equations. A semi-discrete entropy estimate for the entire domain is achieved when the new boundary conditions are coupled with an entropy stable discrete interior operator. The data at the boundary are weakly imposed using a penalty flux approach and a simultaneous-approximation-term penalty technique. Although discontinuous spectral collocation operators on unstructured grids are used herein for the purpose of demonstrating their robustness and efficacy, the new boundary conditions are compatible with any diagonal norm summation-by-parts spatial operator, including finite element, finite difference, finite volume, discontinuous Galerkin, and flux reconstruction/correction procedure via reconstruction schemes. The proposed boundary treatment is tested for three-dimensional subsonic and supersonic flows. The numerical computations corroborate the non-linear stability (entropy stability) and accuracy of the boundary conditions.

  4. Entropy Stable Wall Boundary Conditions for the Compressible Navier-Stokes Equations

    Science.gov (United States)

    Parsani, Matteo; Carpenter, Mark H.; Nielsen, Eric J.

    2014-01-01

    Non-linear entropy stability and a summation-by-parts framework are used to derive entropy stable wall boundary conditions for the compressible Navier-Stokes equations. A semi-discrete entropy estimate for the entire domain is achieved when the new boundary conditions are coupled with an entropy stable discrete interior operator. The data at the boundary are weakly imposed using a penalty flux approach and a simultaneous-approximation-term penalty technique. Although discontinuous spectral collocation operators are used herein for the purpose of demonstrating their robustness and efficacy, the new boundary conditions are compatible with any diagonal norm summation-by-parts spatial operator, including finite element, finite volume, finite difference, discontinuous Galerkin, and flux reconstruction schemes. The proposed boundary treatment is tested for three-dimensional subsonic and supersonic flows. The numerical computations corroborate the non-linear stability (entropy stability) and accuracy of the boundary conditions.

  5. Approaches to daily body condition management in patients with stable chronic obstructive pulmonary disease.

    Science.gov (United States)

    Kawada, Terue

    2016-11-01

    To clarify the characteristics of sub-groups of patients with stable chronic obstructive pulmonary disease having similar approaches to daily body condition management. Prior literature has shed light on the experience of patients with chronic obstructive pulmonary disease and revealed that these patients engage in many activities and try different things in their daily lives to regulate and manage their body condition. The research so far has all been qualitative, comprising mostly interviews, and no quantitative studies have been performed. In this study, cluster analysis was used to show that subgroups of patients with similar characteristics undertake similar approaches to body condition management. Descriptive, correlational study. Invitations to participate in the survey were extended to patients with stable chronic obstructive pulmonary disease. Cluster analysis was performed on the basis of questionnaire scores relating to nine different categories of daily body condition management actions. The characteristics of the body condition management approaches, in each subgroup, were investigated using analysis of variance and multiple comparisons. The cluster analysis produced six subgroups, each defined by the effort expended as part of their body condition management. The subgroups also differed depending on patient age and disease severity. Body condition management approaches taken by patients with stable chronic obstructive pulmonary disease are overall, comprehensive approaches. Patients with chronic obstructive pulmonary disease were subgrouped based on their engagement in body conditioning. Relationships between the subgroups and the engagement in body conditioning, age and shortness of breath severity were observed. The care of patient support should be comprehensive and depend on their age and the duration of the disease. In addition, it should be long term and recognise that the patients are living their own respective lives. Such considerations and

  6. A stable enol from a 6-substituted benzanthrone and its unexpected behaviour under acidic conditions

    Directory of Open Access Journals (Sweden)

    Marc Debeaux

    2009-06-01

    Full Text Available Treatment of benzanthrone (1 with biphenyl-2-yl lithium leads to the surprisingly stable enol 4, which is converted by dehydrogenation into the benzanthrone derivative 7. Under acidic conditions 4 isomerises to the spiro compound 11 and the bicyclo[4.3.1]decane derivative 12. Furthermore, the formation of 7 and the hydrogenated compound 13 is observed. A mechanism for the formation of the reaction products is proposed and supported by DFT calculations.

  7. Operational Markov Condition for Quantum Processes

    Science.gov (United States)

    Pollock, Felix A.; Rodríguez-Rosario, César; Frauenheim, Thomas; Paternostro, Mauro; Modi, Kavan

    2018-01-01

    We derive a necessary and sufficient condition for a quantum process to be Markovian which coincides with the classical one in the relevant limit. Our condition unifies all previously known definitions for quantum Markov processes by accounting for all potentially detectable memory effects. We then derive a family of measures of non-Markovianity with clear operational interpretations, such as the size of the memory required to simulate a process or the experimental falsifiability of a Markovian hypothesis.

  8. Generation and monitoring of a discrete stable random process

    CERN Document Server

    Hopcraft, K I; Matthews, J O

    2002-01-01

    A discrete stochastic process with stationary power law distribution is obtained from a death-multiple immigration population model. Emigrations from the population form a random series of events which are monitored by a counting process with finite-dynamic range and response time. It is shown that the power law behaviour of the population is manifested in the intermittent behaviour of the series of events. (letter to the editor)

  9. Stable image acquisition for mobile image processing applications

    Science.gov (United States)

    Henning, Kai-Fabian; Fritze, Alexander; Gillich, Eugen; Mönks, Uwe; Lohweg, Volker

    2015-02-01

    Today, mobile devices (smartphones, tablets, etc.) are widespread and of high importance for their users. Their performance as well as versatility increases over time. This leads to the opportunity to use such devices for more specific tasks like image processing in an industrial context. For the analysis of images requirements like image quality (blur, illumination, etc.) as well as a defined relative position of the object to be inspected are crucial. Since mobile devices are handheld and used in constantly changing environments the challenge is to fulfill these requirements. We present an approach to overcome the obstacles and stabilize the image capturing process such that image analysis becomes significantly improved on mobile devices. Therefore, image processing methods are combined with sensor fusion concepts. The approach consists of three main parts. First, pose estimation methods are used to guide a user moving the device to a defined position. Second, the sensors data and the pose information are combined for relative motion estimation. Finally, the image capturing process is automated. It is triggered depending on the alignment of the device and the object as well as the image quality that can be achieved under consideration of motion and environmental effects.

  10. Conditional CO2 flux analysis of a managed grassland with the aid of stable isotopes

    Science.gov (United States)

    Zeeman, M. J.; Tuzson, B.; Emmenegger, L.; Knohl, A.; Buchmann, N.; Eugster, W.

    2009-04-01

    Short statured managed ecosystems, such as agricultural grasslands, exhibit high temporal changes in carbon dioxide assimilation and respiration fluxes for which measurements of the net CO2 flux, e.g. by using the eddy covariance (EC) method, give only limited insight. We have therefore adopted a recently proposed concept for conditional EC flux analysis of forest to grasslands, in order to identify and quantify daytime sub-canopy respiration fluxes. To validate the concept, high frequency (≈5 Hz) stable carbon isotope analyis of CO2 was used. We made eddy covariance measurements of CO2 and its isotopologues during four days in August 2007, using a novel quantum cascade laser absorption spectrometer, capable of high time resolution stable isotope analysis. The effects of a grass cut during the measurement period could be detected and resulted in a sub-canopy source conditional flux classification, for which the isotope composition of the CO2 could be confirmed to be of a respiration source. However, the conditional flux method did not work for an undisturbed grassland canopy. We attribute this to the flux measurement height that was chosen well above the roughness sublayer, where the natural isotopic tracer (δ13C) of respiration was too well mixed with background air.

  11. Stable isotopes to detect food-conditioned bears and to evaluate human-bear management

    Science.gov (United States)

    Hopkins, John B.; Koch, Paul L.; Schwartz, Charles C.; Ferguson, Jake M.; Greenleaf, Schuyler S.; Kalinowski, Steven T.

    2012-01-01

    We used genetic and stable isotope analysis of hair from free-ranging black bears (Ursus americanus) in Yosemite National Park, California, USA to: 1) identify bears that consume human food, 2) estimate the diets of these bears, and 3) evaluate the Yosemite human–bear management program. Specifically, we analyzed the isotopic composition of hair from bears known a priori to be food-conditioned or non-food-conditioned and used these data to predict whether bears with an unknown management status were food-conditioned (FC) or non-food-conditioned (NFC). We used a stable isotope mixing model to estimate the proportional contribution of natural foods (plants and animals) versus human food in the diets of FC bears. We then used results from both analyses to evaluate proactive (population-level) and reactive (individual-level) human–bear management, and discussed new metrics to evaluate the overall human–bear management program in Yosemite. Our results indicated that 19 out of 145 (13%) unknown bears sampled from 2005 to 2007 were food-conditioned. The proportion of human food in the diets of known FC bears likely declined from 2001–2003 to 2005–2007, suggesting proactive management was successful in reducing the amount of human food available to bears. In contrast, reactive management was not successful in changing the management status of known FC bears to NFC bears, or in reducing the contribution of human food to the diets of FC bears. Nine known FC bears were recaptured on 14 occasions from 2001 to 2007; all bears were classified as FC during subsequent recaptures, and human–bear management did not reduce the amount of human food in the diets of FC bears. Based on our results, we suggest Yosemite continue implementing proactive human–bear management, reevaluate reactive management, and consider removing problem bears (those involved in repeated bear incidents) from the population.

  12. Muscular outputs during dynamic bench press under stable versus unstable conditions.

    Science.gov (United States)

    Koshida, Sentaro; Urabe, Yukio; Miyashita, Koji; Iwai, Kanzunori; Kagimori, Aya

    2008-09-01

    Previous studies have suggested that resistance training exercise under unstable conditions decreases the isometric force output, yet little is known about its influence on muscular outputs during dynamic movement. The objective of this study was to investigate the effect of an unstable condition on power, force, and velocity outputs during the bench press. Twenty male collegiate athletes (mean age, 21.3 +/- 1.5 years; mean height, 167.7 +/- 7.7 cm; mean weight, 75.9 +/- 17.5 kg) participated in this study. Each subject attempted 3 sets of single bench presses with 50% of 1 repetition maximum (1RM) under a stable condition with a flat bench and an unstable condition with a Swiss ball. Acceleration data were obtained with an accelerometer attached to the center of a barbell shaft, and peak outputs of power, force, and velocity were computed. Although significant loss of the peak outputs was found under the unstable condition (p velocity outputs, compared with previous findings. Such small reduction rates of muscular outputs may not compromise the training effect. Prospective studies are necessary to confirm whether the resistance training under an unstable condition permits the improvement of dynamic performance and trunk stability.

  13. Hematopoietic differentiation: a coordinated dynamical process towards attractor stable states

    Directory of Open Access Journals (Sweden)

    Rossi Simona

    2010-06-01

    Full Text Available Abstract Background The differentiation process, proceeding from stem cells towards the different committed cell types, can be considered as a trajectory towards an attractor of a dynamical process. This view, taking into consideration the transcriptome and miRNome dynamics considered as a whole, instead of looking at few 'master genes' driving the system, offers a novel perspective on this phenomenon. We investigated the 'differentiation trajectories' of the hematopoietic system considering a genome-wide scenario. Results We developed serum-free liquid suspension unilineage cultures of cord blood (CB CD34+ hematopoietic progenitor cells through erythroid (E, megakaryocytic (MK, granulocytic (G and monocytic (Mo pathways. These cultures recapitulate physiological hematopoiesis, allowing the analysis of almost pure unilineage precursors starting from initial differentiation of HPCs until terminal maturation. By analyzing the expression profile of protein coding genes and microRNAs in unilineage CB E, MK, G and Mo cultures, at sequential stages of differentiation and maturation, we observed a coordinated, fully interconnected and scalable character of cell population behaviour in both transcriptome and miRNome spaces reminiscent of an attractor-like dynamics. MiRNome and transcriptome space differed for a still not terminally committed behaviour of microRNAs. Conclusions Consistent with their roles, the transcriptome system can be considered as the state space of a cell population, while the continuously evolving miRNA space corresponds to the tuning system necessary to reach the attractor. The behaviour of miRNA machinery could be of great relevance not only for the promise of reversing the differentiated state but even for tumor biology.

  14. Impact of atmospheric release in stable night meteorological conditions; can emergency models predict dispersion

    Energy Technology Data Exchange (ETDEWEB)

    Connan, O.; Hebert, D.; Solier, L.; Voiseux, C.; Lamotte, M.; Laguionie, P.; Maro, D.; Thomas, L. [IRSN/PRP-ENV/SERIS/LRC (France)

    2014-07-01

    Atmospheric dispersion of pollutant or radionuclides in stratified meteorological condition, i.e. especially when weather conditions are very stable, mainly at night, is still poorly understood and not well apprehended by the operational atmospheric dispersion models. However, correctly predicting the dispersion of a radioactive plume, and estimating the radiological consequences for the population, following an unplanned atmospheric release of radionuclides are crucial steps in an emergency response. To better understand dispersion in these special weather conditions, IRSN performed a series of 22 air sampling campaigns between 2010 and 2013 in the vicinity of the La Hague nuclear reprocessing plant (AREVA - NC, France), at distances between 200 m and 3000 m from the facility. Krypton-85 ({sup 85}Kr), a b-and g-emitting radionuclide, released during the reprocessing of spent nuclear fuel was used as a non-reactive tracer of radioactive plumes. Experimental campaigns were realized in stability class stable or very stable (E or F according to Pasquill classification) 18 times, and in neutral conditions (D according to Pasquill classification) 4 times. During each campaign, Krypton-85 real time measurement were made to find the plume around the plant, and then integrated samples (30 min) were collected in bag perpendicularly to the assumed wind direction axis. After measurement by gamma spectrometry, we have, when it was possible, estimate the point of impact and the width of the plume. The objective was to estimate the horizontal dispersion (width) of the plume at ground level in function of the distance and be able to calculate atmospheric transfer coefficients. In a second step, objective was to conclude on the use of common model and on their uncertainties. The results will be presented in terms of impact on the near-field. They will be compared with data obtained in previous years in neutral atmospheric conditions, and finally the results will be confronted with

  15. New Polymorph of Fe3O4 Stable at Core-Mantle Boundary Conditions

    Science.gov (United States)

    Greenberg, E.; Prakapenka, V. B.

    2017-12-01

    Magnetite Fe3O4 (and its high-pressure polymorphs) is one of the most studied iron bearing minerals. One reason for the interest in magnetite is that it contains both Fe2+ and Fe3+, which is especially important for understanding the physical and chemical properties of Earth's deep interior. Early studies on magnetite debated the nature of the structural phase transition at 35 GPa [1-4]. This high-pressure structure was shown to be of the CaTi2O4-type [5], but with Fe3+ occupying multiple sites. Furthermore, at pressures above 65 GPa a second structural transition to a Pmma space group was shown to take place [5], similar to that in Fe3-xTixO4 solid solution [6]. Other studies have focused on the P-T stability of Fe3O4. Early studies by Lazor et al. [7] predicted that Fe3O4 might disproportionate into FeO and h-Fe2O3 at 50 GPa. Other studies suggested that the high-pressure phase should be stable up to 100 GPa [3]. A more recent experimental study by Ricolleau and Fei [8] revealed that Fe3O4 is stable at least up to 103 GPa. Thus far, structural studies of Fe3O4 have been limited to pressures below 105 GPa. We have studied Fe3O4 up to pressures of 175 GPa and temperatures above 4000K, using diamond anvil cells in combination with synchrotron x-ray diffraction and an online pulsed laser-heating system to study the stability of Fe3O4 at relevant pressure-temperature conditions. Our results show that Fe3O4 is stable up to at least 176 GPa and 4200 K. We have discovered a new polymorph of Fe3O4 at these high P-T conditions. This new phase is stable in the pressure range of at least 100Journal of Physics: Condensed Matter 15, 7697 (2003). [4] Xu et al. Pysical Review B 70, 174106 (2004). [5] Greenberg et al. Physical Review B 95, 195150 (2017). [6] Yamanaka et al. American Mineralogist 98, 736 (2013). [7] Lazor et al. Journal of Geophysical Research 109, B05201 (2004). [8] Ricolleau and Fei. American Mineralogist 101, 719 (2016).

  16. Air conditioning for data processing system areas

    Directory of Open Access Journals (Sweden)

    Hernando Camacho García

    1996-09-01

    Full Text Available The appropiate selection of air conditioners for data processing system areas requires the knowledge of the environmental desing conditions, the air conditioning systems succssfully used computer and the cooling loads to handle. This work contains information about a wide variety of systems designed for computer room applications. a complete example of calculation to determine the amount of heat to be removed for satisfactory operation, is also included.

  17. Levy Stable Processes. From Stationary to Self-Similar Dynamics and Back. An Application to Finance

    International Nuclear Information System (INIS)

    Burnecki, K.; Weron, A.

    2004-01-01

    We employ an ergodic theory argument to demonstrate the foundations of ubiquity of Levy stable self-similar processes in physics and present a class of models for anomalous and nonextensive diffusion. A relationship between stationary and self-similar models is clarified. The presented stochastic integral description of all Levy stable processes could provide new insights into the mechanism underlying a range of self-similar natural phenomena. Finally, this effect is illustrated by self-similar approach to financial modelling. (author)

  18. Design and optimization of food processing conditions

    OpenAIRE

    Silva, C. L. M.

    1996-01-01

    The main research objectives of the group are the design and optimization of food processing conditions. Most of the work already developed is on the use of mathematical modeling of transport phenomena and quantification of degradation kinetics as two tools to optimize the final quality of thermally processed food products. Recently, we initiated a project with the main goal of studying the effects of freezing and frozen storage on orange and melon juice pectinesterase activity and q...

  19. Process conditions and volumetric composition in composites

    DEFF Research Database (Denmark)

    Madsen, Bo

    2013-01-01

    The obtainable volumetric composition in composites is linked to the gravimetric composition, and it is influenced by the conditions of the manufacturing process. A model for the volumetric composition is presented, where the volume fractions of fibers, matrix and porosity are calculated...... as a function of the fiber weight fraction, and where parameters are included for the composite microstructure, and the fiber assembly compaction behavior. Based on experimental data of composites manufactured with different process conditions, together with model predictions, different types of process related...... effects are analyzed. The applied consolidation pressure is found to have a marked effect on the volumetric composition. A power-law relationship is found to well describe the found relations between the maximum obtainable fiber volume fraction and the consolidation pressure. The degree of fiber...

  20. Force Outputs during Squats Performed Using a Rotational Inertia Device under Stable versus Unstable Conditions with Different Loads.

    Science.gov (United States)

    Vázquez-Guerrero, Jairo; Moras, Gerard; Baeza, Jennifer; Rodríguez-Jiménez, Sergio

    2016-01-01

    The purpose of the study was to compare the force outputs achieved during a squat exercise using a rotational inertia device in stable versus unstable conditions with different loads and in concentric and eccentric phases. Thirteen male athletes (mean ± SD: age 23.7 ± 3.0 years, height 1.80 ± 0.08 m, body mass 77.4 ± 7.9 kg) were assessed while squatting, performing one set of three repetitions with four different loads under stable and unstable conditions at maximum concentric effort. Overall, there were no significant differences between the stable and unstable conditions at each of the loads for any of the dependent variables. Mean force showed significant differences between some of the loads in stable and unstable conditions (P inertia device allowed the generation of similar force outputs under stable and unstable conditions at each of the four loads. The study also provides empirical evidence of the different force outputs achieved by adjusting load conditions on the rotational inertia device when performing squats, especially in the case of peak force. Concentric force outputs were significantly higher than eccentric outputs, except for peak force under both conditions. These findings support the use of the rotational inertia device to train the squatting exercise under unstable conditions for strength and conditioning trainers. The device could also be included in injury prevention programs for muscle lesions and ankle and knee joint injuries.

  1. Polymer solar cells - Non toxic processing and stable polymer photovoltaic materials

    Energy Technology Data Exchange (ETDEWEB)

    Soendergaard, R

    2012-07-01

    high to allow processing on flexible substrates like PET. As a final result, the reduction in cleavage temperature of thermocleavable thiophene polymers with ester side chains, through acid catalysis have been examined. The study shows that substantial lowering of the temperatures can be obtained for tertiary, secondary and primary esters, but further research needs to be performed in order to transfer the reaction to solar cells. From a stability point of view, the current state of the art polymers are not stable enough to be processed by large area processing methods like roll-to-roll (R2R) coating techniques, as this has to be performed in air. This calls for the development of new materials, which can endure such processing conditions, and in this context it would be preferable to have a guideline towards which properties of a polymer that either induces stability or causes it to degrade. As part of a larger study, aiming at mapping the relative stability influence of different donors and acceptors in low-band-gap polymers, four polymers were synthesized for examination of their photochemical stabilities. Two of these were furthermore optimized for R2R processing and were tested together with other cells, in an outdoor study involving 8 countries. Panels containing the cells encapsulated in polyurethane were manufactured, measured and installed by travelling between the different locations. Following 4 1/2 months outdoor exposure the trip was done again in order to dismount the panels for shipment back to Denmark, where final characterization was made. The use of polyurethane for encapsulation showed improved conservations of the cells compared to previous studies. (Author)

  2. Force Outputs during Squats Performed Using a Rotational Inertia Device under Stable versus Unstable Conditions with Different Loads.

    Directory of Open Access Journals (Sweden)

    Jairo Vázquez-Guerrero

    Full Text Available The purpose of the study was to compare the force outputs achieved during a squat exercise using a rotational inertia device in stable versus unstable conditions with different loads and in concentric and eccentric phases. Thirteen male athletes (mean ± SD: age 23.7 ± 3.0 years, height 1.80 ± 0.08 m, body mass 77.4 ± 7.9 kg were assessed while squatting, performing one set of three repetitions with four different loads under stable and unstable conditions at maximum concentric effort. Overall, there were no significant differences between the stable and unstable conditions at each of the loads for any of the dependent variables. Mean force showed significant differences between some of the loads in stable and unstable conditions (P < 0.010 and peak force output differed between all loads for each condition (P < 0.045. Mean force outputs were greater in the concentric than in the eccentric phase under both conditions and with all loads (P < 0.001. There were no significant differences in peak force between concentric and eccentric phases at any load in either stable or unstable conditions. In conclusion, squatting with a rotational inertia device allowed the generation of similar force outputs under stable and unstable conditions at each of the four loads. The study also provides empirical evidence of the different force outputs achieved by adjusting load conditions on the rotational inertia device when performing squats, especially in the case of peak force. Concentric force outputs were significantly higher than eccentric outputs, except for peak force under both conditions. These findings support the use of the rotational inertia device to train the squatting exercise under unstable conditions for strength and conditioning trainers. The device could also be included in injury prevention programs for muscle lesions and ankle and knee joint injuries.

  3. Gaussian Process-Mixture Conditional Heteroscedasticity.

    Science.gov (United States)

    Platanios, Emmanouil A; Chatzis, Sotirios P

    2014-05-01

    Generalized autoregressive conditional heteroscedasticity (GARCH) models have long been considered as one of the most successful families of approaches for volatility modeling in financial return series. In this paper, we propose an alternative approach based on methodologies widely used in the field of statistical machine learning. Specifically, we propose a novel nonparametric Bayesian mixture of Gaussian process regression models, each component of which models the noise variance process that contaminates the observed data as a separate latent Gaussian process driven by the observed data. This way, we essentially obtain a Gaussian process-mixture conditional heteroscedasticity (GPMCH) model for volatility modeling in financial return series. We impose a nonparametric prior with power-law nature over the distribution of the model mixture components, namely the Pitman-Yor process prior, to allow for better capturing modeled data distributions with heavy tails and skewness. Finally, we provide a copula-based approach for obtaining a predictive posterior for the covariances over the asset returns modeled by means of a postulated GPMCH model. We evaluate the efficacy of our approach in a number of benchmark scenarios, and compare its performance to state-of-the-art methodologies.

  4. Highly stable and degradable multifunctional microgel for self-regulated insulin delivery under physiological conditions

    Science.gov (United States)

    Zhang, Xinjie; Lü, Shaoyu; Gao, Chunmei; Chen, Chen; Zhang, Xuan; Liu, Mingzhu

    2013-06-01

    The response to glucose, pH and temperature, high drug loading capacity, self-regulated drug delivery and degradation in vivo are simultaneously probable by applying a multifunctional microgel under a rational design in a colloid chemistry method. Such multifunctional microgels are fabricated with N-isopropylacrylamide (NIPAAm), (2-dimethylamino)ethyl methacrylate (DMAEMA) and 3-acrylamidephenylboronic acid (AAPBA) through a precipitation emulsion method and cross-linked by reductive degradable N,N'-bis(arcyloyl)cystamine (BAC). This novel kind of microgel with a narrow size distribution (~250 nm) is suitable for diabetes because it can adapt to the surrounding medium of different glucose concentrations over a clinically relevant range (0-20 mM), control the release of preloaded insulin and is highly stable under physiological conditions (pH 7.4, 0.15 M NaCl, 37 °C). When synthesized multifunctional microgels regulate drug delivery, they gradually degrade as time passes and, as a result, show enhanced biocompatibility. This exhibits a new proof-of-concept for diabetes treatment that takes advantage of the properties of each building block from a multifunctional micro-object. These highly stable and versatile multifunctional microgels have the potential to be used for self-regulated therapy and monitoring of the response to treatment, or even simultaneous diagnosis as nanobiosensors.The response to glucose, pH and temperature, high drug loading capacity, self-regulated drug delivery and degradation in vivo are simultaneously probable by applying a multifunctional microgel under a rational design in a colloid chemistry method. Such multifunctional microgels are fabricated with N-isopropylacrylamide (NIPAAm), (2-dimethylamino)ethyl methacrylate (DMAEMA) and 3-acrylamidephenylboronic acid (AAPBA) through a precipitation emulsion method and cross-linked by reductive degradable N,N'-bis(arcyloyl)cystamine (BAC). This novel kind of microgel with a narrow size

  5. Development of a setup to enable stable and accurate flow conditions for membrane biofouling studies

    KAUST Repository

    Bucs, Szilard

    2015-07-10

    Systematic laboratory studies on membrane biofouling require experimental conditions that are well defined and representative for practice. Hydrodynamics and flow rate variations affect biofilm formation, morphology, and detachment and impacts on membrane performance parameters such as feed channel pressure drop. There is a suite of available monitors to study biofouling, but systems to operate monitors have not been well designed to achieve an accurate, constant water flow required for a reliable determination of biomass accumulation and feed channel pressure drop increase. Studies were done with membrane fouling simulators operated in parallel with manual and automated flow control, with and without dosage of a biodegradable substrate to the feedwater to enhance biofouling rate. High flow rate variations were observed for the manual water flow system (up to ≈9%) compared to the automatic flow control system (<1%). The flow rate variation in the manual system was strongly increased by biofilm accumulation, while the automatic system maintained an accurate and constant water flow in the monitor. The flow rate influences the biofilm accumulation and the impact of accumulated biofilm on membrane performance. The effect of the same amount of accumulated biomass on the pressure drop increase was related to the linear flow velocity. Stable and accurate feedwater flow rates are essential for biofouling studies in well-defined conditions in membrane systems. © 2015 Balaban Desalination Publications. All rights reserved.

  6. Fuel corrosion processes under waste disposal conditions

    International Nuclear Information System (INIS)

    Shoesmith, D.W.

    2000-01-01

    The release of the majority of radionuclides from spent nuclear fuel under permanent disposal conditions will be controlled by the rate of dissolution of the UO 2 fuel matrix. In this manuscript the mechanism of the coupled anodic (fuel dissolution) and cathodic (oxidant reduction) reactions which constitute the overall fuel corrosion process is reviewed, and the many published observations on fuel corrosion under disposal conditions discussed. The primary emphasis is on summarizing the overall mechanistic behaviour and establishing the primary factors likely to control fuel corrosion. Included are discussions on the influence of various oxidants including radiolytic ones, pH, temperature, groundwater composition, and the formation of corrosion product deposits. The relevance of the data recorded on unirradiated UO 2 to the interpretation of spent fuel behaviour is included. Based on the review, the data used to develop fuel corrosion models under the conditions anticipated in Yucca Mountain (NV, USA) are evaluated

  7. Conditioning from an information processing perspective.

    Science.gov (United States)

    Gallistel, C R.

    2003-04-28

    The framework provided by Claude Shannon's [Bell Syst. Technol. J. 27 (1948) 623] theory of information leads to a quantitatively oriented reconceptualization of the processes that mediate conditioning. The focus shifts from processes set in motion by individual events to processes sensitive to the information carried by the flow of events. The conception of what properties of the conditioned and unconditioned stimuli are important shifts from the tangible properties to the intangible properties of number, duration, frequency and contingency. In this view, a stimulus becomes a CS if its onset substantially reduces the subject's uncertainty about the time of occurrence of the next US. One way to represent the subject's knowledge of that time of occurrence is by the cumulative probability function, which has two limiting forms: (1) The state of maximal uncertainty (minimal knowledge) is represented by the inverse exponential function for the random rate condition, in which the US is equally likely at any moment. (2) The limit to the subject's attainable certainty is represented by the cumulative normal function, whose momentary expectation is the CS-US latency minus the time elapsed since CS onset. Its standard deviation is the Weber fraction times the CS-US latency.

  8. Reinventing a p-type doping process for stable ZnO light emitting devices

    Science.gov (United States)

    Xie, Xiuhua; Li, Binghui; Zhang, Zhenzhong; Shen, Dezhen

    2018-06-01

    A tough challenge for zinc oxide (ZnO) as the ultraviolet optoelectronics materials is realizing the stable and reliable p-type conductivity. Self-compensation, coming from native donor-type point defects, is a big obstacle. In this work, we introduce a dynamic N doping process with molecular beam epitaxy, which is accomplished by a Zn, N-shutter periodic switch (a certain time shift between them for independent optimization of surface conditions). During the epitaxy, N adatoms are incorporated under the condition of (2  ×  2)  +  Zn vacancies reconstruction on a Zn-polar surface, at which oxygen vacancies (V O), the dominating compensating donors, are suppressed. With the p-ZnO with sufficient holes surviving, N concentration ~1  ×  1019 cm‑3, is employed in a p-i-n light emitting devices. Significant ultraviolet emission of electroluminescence spectra without broad green band (related to V O) at room-temperature are demonstrated. The devices work incessantly without intentional cooling for over 300 h at a luminous intensity reduction of one order of magnitude under the driving of a 10 mA continuous current, which are the demonstration for p-ZnO stability and reliability.

  9. Heat storage in forest biomass significantly improves energy balance closure particularly during stable conditions

    Science.gov (United States)

    Lindroth, A.; Mölder, M.; Lagergren, F.

    2009-08-01

    Temperature measurements in trunks and branches in a mature ca. 100 years-old mixed pine and spruce forest in central Sweden were used to estimate the heat storage in the tree biomass. The estimated heat flux in the sample trees and data on biomass distributions were used to scale up to stand level biomass heat fluxes. The rate of change of sensible and latent heat storage in the air layer below the level of the flux measurements was estimated from air temperature and humidity profile measurements and soil heat flux was estimated from heat flux plates and soil temperature measurements. The fluxes of sensible and latent heat from the forest were measured with an eddy covariance system in a tower. The analysis was made for a two-month period in summer of 1995. The tree biomass heat flux was the largest of the estimated storage components and varied between 40 and -35 W m-2 on summer days with nice weather. Averaged over two months the diurnal maximum of total heat storage was 45 W m-2 and the minimum was -35 W m-2. The soil heat flux and the sensible heat storage in air were out of phase with the biomass flux and they reached maximum values that were about 75% of the maximum of the tree biomass heat storage. The energy balance closure improved significantly when the total heat storage was added to the turbulent fluxes. The slope of a regression line with sum of fluxes and storage as independent and net radiation as dependent variable, increased from 0.86 to 0.95 for half-hourly data and the scatter was also reduced. The most significant finding was, however, that during nights with strongly stable conditions when the sensible heat flux dropped to nearly zero, the total storage matched the net radiation nearly perfectly. Another interesting result was that the mean energy imbalance started to increase when the Richardson number became more negative than ca. -0.1. In fact, the largest energy deficit occurred at maximum instability. Our conclusion is that eddy

  10. Attributing Climate Conditions for Stable Malaria Transmission to Human Activity in sub-Saharan Africa

    Science.gov (United States)

    Sheldrake, L.; Mitchell, D.; Allen, M. R.

    2015-12-01

    Temperature and precipitation limit areas of stable malaria transmission, but the effects of climate change on the disease remain controversial. Previously, studies have not separated the influence of anthropogenic climate change and natural variability, despite being an essential step in the attribution of climate change impacts. Ensembles of 2900 simulations of regional climate in sub-Saharan Africa for the year 2013, one representing realistic conditions and the other how climate might have been in the absence of human influence, were used to force a P.falciparium climate suitability model developed by the Mapping Malaria Risk in Africa project. Strongest signals were detected in areas of unstable transmission, indicating their heightened sensitivity to climatic factors. Evidently, impacts of human-induced climate change were unevenly distributed: the probability of conditions being suitable for stable malaria transmission were substantially reduced (increased) in the Sahel (Greater Horn of Africa (GHOA), particularly in the Ethiopian and Kenyan highlands). The length of the transmission season was correspondingly shortened in the Sahel and extended in the GHOA, by 1 to 2 months, including in Kericho (Kenya), where the role of climate change in driving recent malaria occurrence is hotly contested. Human-induced warming was primarily responsible for positive anomalies in the GHOA, while reduced rainfall caused negative anomalies in the Sahel. The latter was associated with anthropogenic impacts on the West African Monsoon, but uncertainty in the RCM's ability to reproduce precipitation trends in the region weakens confidence in the result. That said, outputs correspond well with broad-scale changes in observed endemicity, implying a potentially important contribution of anthropogenic climate change to the malaria burden during the past century. Results support the health-framing of climate risk and help indicate hotspots of climate vulnerability, providing

  11. Dissociable Learning Processes Underlie Human Pain Conditioning.

    Science.gov (United States)

    Zhang, Suyi; Mano, Hiroaki; Ganesh, Gowrishankar; Robbins, Trevor; Seymour, Ben

    2016-01-11

    Pavlovian conditioning underlies many aspects of pain behavior, including fear and threat detection [1], escape and avoidance learning [2], and endogenous analgesia [3]. Although a central role for the amygdala is well established [4], both human and animal studies implicate other brain regions in learning, notably ventral striatum and cerebellum [5]. It remains unclear whether these regions make different contributions to a single aversive learning process or represent independent learning mechanisms that interact to generate the expression of pain-related behavior. We designed a human parallel aversive conditioning paradigm in which different Pavlovian visual cues probabilistically predicted thermal pain primarily to either the left or right arm and studied the acquisition of conditioned Pavlovian responses using combined physiological recordings and fMRI. Using computational modeling based on reinforcement learning theory, we found that conditioning involves two distinct types of learning process. First, a non-specific "preparatory" system learns aversive facial expressions and autonomic responses such as skin conductance. The associated learning signals-the learned associability and prediction error-were correlated with fMRI brain responses in amygdala-striatal regions, corresponding to the classic aversive (fear) learning circuit. Second, a specific lateralized system learns "consummatory" limb-withdrawal responses, detectable with electromyography of the arm to which pain is predicted. Its related learned associability was correlated with responses in ipsilateral cerebellar cortex, suggesting a novel computational role for the cerebellum in pain. In conclusion, our results show that the overall phenotype of conditioned pain behavior depends on two dissociable reinforcement learning circuits. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  12. Development of shelf stable, processed, low acid food products using heat-irradiation combination treatments

    International Nuclear Information System (INIS)

    Minnaar, A.

    1998-01-01

    The amount of ionizing irradiation needed to sterilize low acid vegetable and starch products (with and without sauces) commercially impairs their sensorial and nutritive qualities, and use of thermal processes for the same purpose may also have an adverse effect on the product quality. A systematic approach to the establishment of optimized combination parameters was developed for heat-irradiation processing to produce high quality, shelf stable, low acid food products. The effects of selected heat, heat-irradiation combination and irradiation treatments on the quality of shelf stable mushrooms in brine and rice, stored at ambient temperature, were studied. From a quality viewpoint, use of heat-irradiation combination treatments favouring low irradiation dose levels offered a feasible alternative to thermally processed or radappertized mushrooms in brine. However, shelf stable rice produced by heat-irradiation combination treatments offered a feasible alternative only to radappertized rice from the standpoint of quality. The technical requirements for the heat and irradiation processing of a long grain rice cultivar from the United States of America oppose each other directly, thereby reducing the feasibility of using heat-irradiation combination processing to produce shelf stable rice. The stability of starch thickened white sauces was found to be affected severely during high dose irradiation and subsequent storage at ambient temperature. However, use of pea protein isolate as a thickener in white sauces was found to have the potential to maintain the viscosity of sauces for irradiated meat and sauce products throughout processing and storage. (author)

  13. Treatment of waste salt from the advanced spent fuel conditioning process (II) : optimum immobilization condition

    International Nuclear Information System (INIS)

    Kim, Jeong Guk; Lee, Jae Hee; Yoo, Jae Hyung; Kim, Joon Hyung

    2004-01-01

    Since zeolite is known to be stable at a high temperature, it has been reported as a promising immobilization matrix for waste salt. The crystal structure of dehydrated zeolite A breaks down above 1060 K, resulting in the formation of an amorphous solid and re-crystallization to beta-Cristobalite. This structural degradation depends on the existence of chlorides. When contacted to HCl, zeolite 4A is not stable even at 473 K. The optimum consolidation condition for LiCl salt waste from the oxide fuel reduction process based on the electrochemical method (Advanced spent fuel Conditioning Process; ACP) has been studied using zeolite A since 2001. Actually the constituents of waste salt are water-soluble. And, alkali halides are known to be readily radiolyzed to yield interstitial halogens and metal colloids. For disposal in a geological repository, the waste salt must meet the acceptance criteria. For a waste form containing chloride salt, two of the more important criteria are leach resistance and waste form durability. In this work, we prepared some samples with different mixing ratios of LiCl salt to zeolite A, and then compared some characteristics such as thermal stability, salt occlusion, free chloride content, leach resistance, mixing effect, etc

  14. Starting the universe: Stable violation of the null energy condition and non-standard cosmologies

    International Nuclear Information System (INIS)

    Creminelli, P.; Luty, M.A.; Nicolis, A.; Senatore, L.

    2006-06-01

    We present a consistent effective theory that violates the null energy condition (NEC) without developing any instabilities or other pathological features. The model is the ghost condensate with the global shift symmetry softly broken by a potential. We show that this system can drive a cosmological expansion with H-dot > 0. Demanding the absence of instabilities in this model requires H-dot or approx. H 2 . We then construct a general low-energy effective theory that describes scalar fluctuations about an arbitrary FRW background, and argue that the qualitative features found in our model are very general for stable systems that violate the NEC. Violating the NEC allows dramatically non- standard cosmological histories. To illustrate this, we construct an explicit model in which the expansion of our universe originates from an asymptotically flat state in the past, smoothing out the big-bang singularity within control of a low- energy effective theory. This gives an interesting alternative to standard inflation for solving the horizon problem. We also construct models in which the present acceleration has w < -1; a periodic ever-expanding universe; and a model with a smooth 'bounce' connecting a contracting and expanding phase. (author)

  15. Formation of stable uranium(VI) colloidal nanoparticles in conditions relevant to radioactive waste disposal.

    Science.gov (United States)

    Bots, Pieter; Morris, Katherine; Hibberd, Rosemary; Law, Gareth T W; Mosselmans, J Frederick W; Brown, Andy P; Doutch, James; Smith, Andrew J; Shaw, Samuel

    2014-12-09

    The favored pathway for disposal of higher activity radioactive wastes is via deep geological disposal. Many geological disposal facility designs include cement in their engineering design. Over the long term, interaction of groundwater with the cement and waste will form a plume of a hyperalkaline leachate (pH 10-13), and the behavior of radionuclides needs to be constrained under these extreme conditions to minimize the environmental hazard from the wastes. For uranium, a key component of many radioactive wastes, thermodynamic modeling predicts that, at high pH, U(VI) solubility will be very low (nM or lower) and controlled by equilibrium with solid phase alkali and alkaline-earth uranates. However, the formation of U(VI) colloids could potentially enhance the mobility of U(VI) under these conditions, and characterizing the potential for formation and medium-term stability of U(VI) colloids is important in underpinning our understanding of U behavior in waste disposal. Reflecting this, we applied conventional geochemical and microscopy techniques combined with synchrotron based in situ and ex situ X-ray techniques (small-angle X-ray scattering and X-ray adsorption spectroscopy (XAS)) to characterize colloidal U(VI) nanoparticles in a synthetic cement leachate (pH > 13) containing 4.2-252 μM U(VI). The results show that in cement leachates with 42 μM U(VI), colloids formed within hours and remained stable for several years. The colloids consisted of 1.5-1.8 nm nanoparticles with a proportion forming 20-60 nm aggregates. Using XAS and electron microscopy, we were able to determine that the colloidal nanoparticles had a clarkeite (sodium-uranate)-type crystallographic structure. The presented results have clear and hitherto unrecognized implications for the mobility of U(VI) in cementitious environments, in particular those associated with the geological disposal of nuclear waste.

  16. Can bread processing conditions alter glycaemic response?

    Science.gov (United States)

    Lau, Evelyn; Soong, Yean Yean; Zhou, Weibiao; Henry, Jeyakumar

    2015-04-15

    Bread is a staple food that is traditionally made from wheat flour. This study aimed to compare the starch digestibility of western baked bread and oriental steamed bread. Four types of bread were prepared: western baked bread (WBB) and oriental steamed bread (OSB), modified baked bread (MBB) made with the OSB recipe and WBB processing, and modified steamed bread (MSB) made with the WBB recipe and OSB processing. MBB showed the highest starch digestibility in vitro, followed by WBB, OSB and MSB. A similar trend was observed for glycaemic response in vivo. MBB, WBB, OSB and MSB had a glycaemic index of 75±4, 71±5, 68±5 and 65±4, respectively. Processing differences had a more pronounced effect on starch digestibility in bread, and steamed bread was healthier in terms of glycaemic response. The manipulation of processing conditions could be an innovative route to alter the glycaemic response of carbohydrate-rich foods. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Study on the flow reduction of forced flow superconducting magnet and its stable operation condition

    Energy Technology Data Exchange (ETDEWEB)

    Sugimoto, Makoto [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    2001-03-01

    The forced flow superconducting coil especially made from a Cable-in-Conduit Conductor (CICC) is applied for large-scale devices such as fusion magnets and superconducting magnet energy storage (SMES) because it has high mechanical and electrical performance potential. The flow reduction phenomena caused by AC loss generation due to the pulsed operation was found based on the experimental results of three forced flow superconducting coils. And relation between the AC loss generation and flow reduction was defined from viewpoint of the engineering design and operation of the coils. Also the mechanism of flow reduction was investigated and stable operation condition under the flow reduction was clarified for forced flow superconducting coils. First, experiments of three different large-scale superconducting coils were carried out and experimental database of the flow reduction by AC loss generation was established. It was found experimentally that the flow reduction depends on the AC loss generation (W/m{sup 3}) in all of coils. It means the stable operation condition is defined not only the electro magnetism of superconducting coil but also flow condition. Mechanism of the flow reduction was investigated based on the experimental database. Hydraulics was applied to supercritical helium as a coolant. Also performances of the cryogenic pump by which coolant are supplied to the coil and friction of the superconductor as cooling path is considered for hydraulic estimation. The flow reduction of the coil is clarified and predictable by the equations of continuity, momentum and energy balance. Also total mass flow rate of coolant was discussed. The estimation method in the design phase was developed for total mass flow rate which are required under the flow reduction by AC losses. The friction of the superconductor and performance of cryogenic pump should be required for precise prediction of flow reduction. These values were obtained by the experiment data of coil and

  18. Subsurface Conditions Controlling Uranium Incorporation in Iron Oxides: A Redox Stable Sink

    International Nuclear Information System (INIS)

    Fendorf, Scott

    2016-01-01

    Toxic metals and radionuclides throughout the U.S. Department of Energy Complex pose a serious threat to ecosystems and to human health. Of particular concern is the redox-sensitive radionuclide uranium, which is classified as a priority pollutant in soils and groundwaters at most DOE sites owing to its large inventory, its health risks, and its mobility with respect to primary waste sources. The goal of this research was to contribute to the long-term mission of the Subsurface Biogeochemistry Program by determining reactions of uranium with iron (hydr)oxides that lead to long-term stabilization of this pervasive contaminant. The research objectives of this project were thus to (1) identify the (bio)geochemical conditions, including those of the solid-phase, promoting uranium incorporation in Fe (hydr)oxides, (2) determine the magnitude of uranium incorporation under a variety of relevant subsurface conditions in order to quantify the importance of this pathway when in competition with reduction or adsorption; (3) identify the mechanism(s) of U(VI/V) incorporation in Fe (hydr)oxides; and (4) determine the stability of these phases under different biogeochemical (inclusive of redox) conditions. Our research demonstrates that redox transformations are capable of achieving U incorporation into goethite at ambient temperatures, and that this transformation occurs within days at U and Fe(II) concentrations that are common in subsurface geochemical environments with natural ferrihydrites - inclusive of those with natural impurities. Increasing Fe(II) or U concentration, or initial pH, made U(VI) reduction to U(IV) a more competitive sequestration pathway in this system, presumably by increasing the relative rate of U reduction. Uranium concentrations commonly found in contaminated subsurface environments are often on the order of 1-10 μM, and groundwater Fe(II) concentrations can reach exceed 1 mM in reduced zones of the subsurface. The redox-driven U(V) incorporation

  19. Subsurface Conditions Controlling Uranium Incorporation in Iron Oxides: A Redox Stable Sink

    Energy Technology Data Exchange (ETDEWEB)

    Fendorf, Scott [Stanford Univ., CA (United States)

    2016-04-05

    Toxic metals and radionuclides throughout the U.S. Department of Energy Complex pose a serious threat to ecosystems and to human health. Of particular concern is the redox-sensitive radionuclide uranium, which is classified as a priority pollutant in soils and groundwaters at most DOE sites owing to its large inventory, its health risks, and its mobility with respect to primary waste sources. The goal of this research was to contribute to the long-term mission of the Subsurface Biogeochemistry Program by determining reactions of uranium with iron (hydr)oxides that lead to long-term stabilization of this pervasive contaminant. The research objectives of this project were thus to (1) identify the (bio)geochemical conditions, including those of the solid-phase, promoting uranium incorporation in Fe (hydr)oxides, (2) determine the magnitude of uranium incorporation under a variety of relevant subsurface conditions in order to quantify the importance of this pathway when in competition with reduction or adsorption; (3) identify the mechanism(s) of U(VI/V) incorporation in Fe (hydr)oxides; and (4) determine the stability of these phases under different biogeochemical (inclusive of redox) conditions. Our research demonstrates that redox transformations are capable of achieving U incorporation into goethite at ambient temperatures, and that this transformation occurs within days at U and Fe(II) concentrations that are common in subsurface geochemical environments with natural ferrihydrites—inclusive of those with natural impurities. Increasing Fe(II) or U concentration, or initial pH, made U(VI) reduction to U(IV) a more competitive sequestration pathway in this system, presumably by increasing the relative rate of U reduction. Uranium concentrations commonly found in contaminated subsurface environments are often on the order of 1-10 μM, and groundwater Fe(II) concentrations can reach exceed 1 mM in reduced zones of the subsurface. The redox-driven U(V) incorporation

  20. Variations in the stable isotope ratios of specific aromatic and aliphatic hydrocarbons from coal conversion processes

    Energy Technology Data Exchange (ETDEWEB)

    McRae, C.; Snape, C.E.; Fallick, A.E. [University of Strathclyde, Glasgow (United Kingdom). Dept. of Pure and Applied Chemistry

    1998-07-01

    To establish the scope for applying gas chromatography-isotope ratio mass spectrometry ({sup {delta}-13}C GC-IRMS) to molecular recognition problems in coal utilisation, {sup 13}C/{sup 12}C isotope ratios were determined for n-alkanes and polycyclic aromatic hydrocarbons (PAHs) as a function of coal rank and process conditions. Six coals ranging from a lignite to a low volatile bituminous coal were subjected to chloroform extraction, fixed-bed pyrolysis under hydrogen pressure (hydropyrolysis) and fluidised-bed (flash) pyrolysis. No significant variations in the stable isotope ratios of n-alkanes were evident as a function of either rank or conversion regime. In contrast, the isotope ratios of PAHs show large variations with those for hydropyrolysis (-23 to -25 parts per thousand) being similar to the bulk values of the initial coals and being isotopically heavier (less negative) than their fluidised-bed pyrolysis counterparts by 2-3 parts per thousand. However, the PAHs from fluidised-bed pyrolysis, which resemble closely those obtained from high temperature coal carbonization, are still heavier (by 2-3 parts per thousand) than those from diesel particulates and coal gasification and combustion residues. This provides a firm basis for the source apportionment of airborne PAHs in the proximity of coking plants, particularly with no major variations in the PAH isotope ratios being found as a function of rank.

  1. Progresses in the stable isotope studies of microbial processes associated with wetland methane production

    International Nuclear Information System (INIS)

    Li Qing; Lin Guanghui

    2013-01-01

    Methane emissions from wetlands play a key role in regulating global atmospheric methane concentration, so better understanding of microbial processes for the methane emission in wetlands is critical for developing process models and reducing uncertainty in global methane emission inventory. In this review, we describe basic microbial processes for wetland methane production and then demonstrate how stable isotope fractionation and stable isotope probing can be used to investigate the mechanisms underlying different methanogenic pathways and to quantify microbial species involved in wetland methane production. When applying stable isotope technique to calculate contributions of different pathways to the total methane production in various wetlands, the technical challenge is how to determine isotopic fractionation factors for the acetate derived methane production and carbon dioxide derived methane production. Although the application of stable isotope probing techniques to study the actual functions of different microbial organisms to methane production process is significantly superior to the traditional molecular biology method, the combination of these two technologies will be crucial for direct linking of the microbial community and functional structure with the corresponding metabolic functions, and provide new ideas for future studies. (authors)

  2. Ruin probability with claims modeled by a stationary ergodic stable process

    NARCIS (Netherlands)

    Mikosch, T.; Samorodnitsky, G.

    2000-01-01

    For a random walk with negative drift we study the exceedance probability (ruin probability) of a high threshold. The steps of this walk (claim sizes) constitute a stationary ergodic stable process. We study how ruin occurs in this situation and evaluate the asymptotic behavior of the ruin

  3. Selective and Stable Ethylbenzene Dehydrogenation to Styrene over Nanodiamonds under Oxygen-lean Conditions.

    Science.gov (United States)

    Diao, Jiangyong; Feng, Zhenbao; Huang, Rui; Liu, Hongyang; Hamid, Sharifah Bee Abd; Su, Dang Sheng

    2016-04-07

    For the first time, significant improvement of the catalytic performance of nanodiamonds was achieved for the dehydrogenation of ethylbenzene to styrene under oxygen-lean conditions. We demonstrated that the combination of direct dehydrogenation and oxidative dehydrogenation indeed occurred on the nanodiamond surface throughout the reaction system. It was found that the active sp(2)-sp(3) hybridized nanostructure was well maintained after the long-term test and the active ketonic carbonyl groups could be generated in situ. A high reactivity with 40% ethylbenzene conversion and 92% styrene selectivity was obtained over the nanodiamond catalyst under oxygen-lean conditions even after a 240 h test, demonstrating the potential of this procedure for application as a promising industrial process for the ethylbenzene dehydrogenation to styrene without steam protection. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  4. An energy-stable method for solving the incompressible Navier-Stokes equations with non-slip boundary condition

    Science.gov (United States)

    Lee, Byungjoon; Min, Chohong

    2018-05-01

    We introduce a stable method for solving the incompressible Navier-Stokes equations with variable density and viscosity. Our method is stable in the sense that it does not increase the total energy of dynamics that is the sum of kinetic energy and potential energy. Instead of velocity, a new state variable is taken so that the kinetic energy is formulated by the L2 norm of the new variable. Navier-Stokes equations are rephrased with respect to the new variable, and a stable time discretization for the rephrased equations is presented. Taking into consideration the incompressibility in the Marker-And-Cell (MAC) grid, we present a modified Lax-Friedrich method that is L2 stable. Utilizing the discrete integration-by-parts in MAC grid and the modified Lax-Friedrich method, the time discretization is fully discretized. An explicit CFL condition for the stability of the full discretization is given and mathematically proved.

  5. A semigroup approach to the strong ergodic theorem of the multistate stable population process.

    Science.gov (United States)

    Inaba, H

    1988-01-01

    "In this paper we first formulate the dynamics of multistate stable population processes as a partial differential equation. Next, we rewrite this equation as an abstract differential equation in a Banach space, and solve it by using the theory of strongly continuous semigroups of bounded linear operators. Subsequently, we investigate the asymptotic behavior of this semigroup to show the strong ergodic theorem which states that there exists a stable distribution independent of the initial distribution. Finally, we introduce the dual problem in order to obtain a logical definition for the reproductive value and we discuss its applications." (SUMMARY IN FRE) excerpt

  6. Fuel corrosion processes under waste disposal conditions

    International Nuclear Information System (INIS)

    Shoesmith, D.W.

    1999-09-01

    Under the oxidizing conditions likely to be encountered in the Yucca Mountain Repository, fuel dissolution is a corrosion process involving the coupling of the anodic dissolution of the fuel with the cathodic reduction of oxidants available within the repository. The oxidants potentially available to drive fuel corrosion are environmental oxygen, supplied by the transport through the permeable rock of the mountain and molecular and radical species produced by the radiolysis of available aerated water. The mechanism of these coupled anodic and cathodic reactions is reviewed in detail. While gaps in understanding remain, many kinetic features of these reactions have been studied in considerable detail, and a reasonably justified mechanism for fuel corrosion is available. The corrosion rate is determined primarily by environmental factors rather than the properties of the fuel. Thus, with the exception of increase in rate due to an increase in surface area, pre-oxidation of the fuel has little effect on the corrosion rate

  7. Fuel corrosion processes under waste disposal conditions

    Energy Technology Data Exchange (ETDEWEB)

    Shoesmith, D.W. [Univ. of Western Ontario, Dept. of Chemistry, London, Ontario (Canada)

    1999-09-01

    Under the oxidizing conditions likely to be encountered in the Yucca Mountain Repository, fuel dissolution is a corrosion process involving the coupling of the anodic dissolution of the fuel with the cathodic reduction of oxidants available within the repository. The oxidants potentially available to drive fuel corrosion are environmental oxygen, supplied by the transport through the permeable rock of the mountain and molecular and radical species produced by the radiolysis of available aerated water. The mechanism of these coupled anodic and cathodic reactions is reviewed in detail. While gaps in understanding remain, many kinetic features of these reactions have been studied in considerable detail, and a reasonably justified mechanism for fuel corrosion is available. The corrosion rate is determined primarily by environmental factors rather than the properties of the fuel. Thus, with the exception of increase in rate due to an increase in surface area, pre-oxidation of the fuel has little effect on the corrosion rate.

  8. Revealing stable processing products from ribosome-associated small RNAs by deep-sequencing data analysis.

    Science.gov (United States)

    Zywicki, Marek; Bakowska-Zywicka, Kamilla; Polacek, Norbert

    2012-05-01

    The exploration of the non-protein-coding RNA (ncRNA) transcriptome is currently focused on profiling of microRNA expression and detection of novel ncRNA transcription units. However, recent studies suggest that RNA processing can be a multi-layer process leading to the generation of ncRNAs of diverse functions from a single primary transcript. Up to date no methodology has been presented to distinguish stable functional RNA species from rapidly degraded side products of nucleases. Thus the correct assessment of widespread RNA processing events is one of the major obstacles in transcriptome research. Here, we present a novel automated computational pipeline, named APART, providing a complete workflow for the reliable detection of RNA processing products from next-generation-sequencing data. The major features include efficient handling of non-unique reads, detection of novel stable ncRNA transcripts and processing products and annotation of known transcripts based on multiple sources of information. To disclose the potential of APART, we have analyzed a cDNA library derived from small ribosome-associated RNAs in Saccharomyces cerevisiae. By employing the APART pipeline, we were able to detect and confirm by independent experimental methods multiple novel stable RNA molecules differentially processed from well known ncRNAs, like rRNAs, tRNAs or snoRNAs, in a stress-dependent manner.

  9. A framework for shear driven dissolution of thermally stable particles during friction stir welding and processing

    Energy Technology Data Exchange (ETDEWEB)

    Palanivel, S. [Advanced Materials and Manufacturing Processes Institute, Center for Friction Stir Processing, Department of Materials Science and Engineering, University of North Texas, Denton, TX 76203 (United States); Arora, A. [Materials Science and Engineering, Indian Institute of Technology Gandhinagar, Palaj, Gandhinagar 382355, Gujarat (India); Doherty, K.J. [U.S. Army Research Laboratory, Materials and Manufacturing Science Division, Aberdeen Proving Ground, MD 21005 (United States); Mishra, R.S., E-mail: Rajiv.Mishra@unt.edu [Advanced Materials and Manufacturing Processes Institute, Center for Friction Stir Processing, Department of Materials Science and Engineering, University of North Texas, Denton, TX 76203 (United States)

    2016-12-15

    A framework is proposed to explain the dissolution and fragmentation of particles during friction stir welding and processing. Two major mechanisms dissolve the particle during the process: (i) thermally activated diffusion, and (ii) dislocation and grain boundary sweeping of atoms. We use a three-dimensional coupled viscoplastic flow and heat transfer model to quantify these mechanisms. For illustration purposes, calculations were done on a thermally stable Mg{sub 2}Y intermetallic that dissolved during processing. The framework is universal and applies to any second phase dissolution and fragmentation during friction stir welding and processing, thus enabling a science-based approach to tailor microstructures.

  10. Safeguardability of advanced spent fuel conditioning process

    Energy Technology Data Exchange (ETDEWEB)

    Li, T. K. (Tien K.); Lee, S. Y. (Sang Yoon); Burr, Tom; Russo, P. A. (Phyllis A.); Menlove, Howard O.; Kim, H. D.; Ko, W. I. (Won Il); Park, S. W.; Park, H. S.

    2004-01-01

    The Advanced Spent Fuel Conditioning Process (ACP) is an electro-metallurgical treatment technique to convert oxide-type spent nuclear fuel into a metallic form. The Korea Atomic Energy Research Institute (KAERI) has been developing this technology since 1977 for the purpose of spent fuel management and is planning to perform a lab-scale demonstration in 2006. By using of this technology, a significant reduction of the volume and heat load of spent fuel is expected, which would lighten the burden of final disposal in terms of disposal size, safety and economics. In the framework of collaboration agreement to develop the safeguards system for the ACP, a joint study on the safeguardability of the ACP technology has been performed by the Los Alamos National Laboratory (LANL) and the KAERI since 2002. In this study, the safeguardability of the ACP technology was examined for the pilot-scale facility. The process and material flows were conceptually designed, and the uncertainties in material accounting were estimated with international target values.

  11. Serum adiponectin level in obese and non-obese COPD patients during acute exacerbation and stable conditions

    Directory of Open Access Journals (Sweden)

    Magdy Mohammad Omar

    2014-04-01

    Conclusion: Serum adiponectin was significantly higher in obese and nonobese COPD than controls, the rising is more during exacerbation than stable condition and more in non obese than obese COPD and non significant correlation between changes in adiponectin and ventilatory functions was found.

  12. Optimal physiological structure of small neurons to guarantee stable information processing

    Science.gov (United States)

    Zeng, S. Y.; Zhang, Z. Z.; Wei, D. Q.; Luo, X. S.; Tang, W. Y.; Zeng, S. W.; Wang, R. F.

    2013-02-01

    Spike is the basic element for neuronal information processing and the spontaneous spiking frequency should be less than 1 Hz for stable information processing. If the neuronal membrane area is small, the frequency of neuronal spontaneous spiking caused by ion channel noise may be high. Therefore, it is important to suppress the deleterious spontaneous spiking of the small neurons. We find by simulation of stochastic neurons with Hodgkin-Huxley-type channels that the leakage system is critical and extremely efficient to suppress the spontaneous spiking and guarantee stable information processing of the small neurons. However, within the physiological limit the potassium system cannot do so. The suppression effect of the leakage system is super-exponential, but that of the potassium system is quasi-linear. With the minor physiological cost and the minimal consumption of metabolic energy, a slightly lower reversal potential and a relatively larger conductance of the leakage system give the optimal physiological structure to suppress the deleterious spontaneous spiking and guarantee stable information processing of small neurons, dendrites and axons.

  13. Stable non-Gaussian self-similar processes with stationary increments

    CERN Document Server

    Pipiras, Vladas

    2017-01-01

    This book provides a self-contained presentation on the structure of a large class of stable processes, known as self-similar mixed moving averages. The authors present a way to describe and classify these processes by relating them to so-called deterministic flows. The first sections in the book review random variables, stochastic processes, and integrals, moving on to rigidity and flows, and finally ending with mixed moving averages and self-similarity. In-depth appendices are also included. This book is aimed at graduate students and researchers working in probability theory and statistics.

  14. Processing Conditions, Rice Properties, Health and Environment

    Directory of Open Access Journals (Sweden)

    Nobutaka Nakamura

    2011-06-01

    Full Text Available Rice is the staple food for nearly two-thirds of the world’s population. Food components and environmental load of rice depends on the rice form that is resulted by different processing conditions. Brown rice (BR, germinated brown rice (GBR and partially-milled rice (PMR contains more health beneficial food components compared to the well milled rice (WMR. Although the arsenic concentration in cooked rice depends on the cooking methods, parboiled rice (PBR seems to be relatively prone to arsenic contamination compared to that of untreated rice, if contaminated water is used for parboiling and cooking. A change in consumption patterns from PBR to untreated rice (non-parboiled, and WMR to PMR or BR may conserve about 43–54 million tons of rice and reduce the risk from arsenic contamination in the arsenic prone area. This study also reveals that a change in rice consumption patterns not only supply more food components but also reduces environmental loads. A switch in production and consumption patterns would improve food security where food grains are scarce, and provide more health beneficial food components, may prevent some diseases and ease the burden on the Earth. However, motivation and awareness of the environment and health, and even a nominal incentive may require for a method switching which may help in building a sustainable society.

  15. Value conditioning modulates visual working memory processes.

    Science.gov (United States)

    Thomas, Paul M J; FitzGibbon, Lily; Raymond, Jane E

    2016-01-01

    Learning allows the value of motivationally salient events to become associated with stimuli that predict those events. Here, we asked whether value associations could facilitate visual working memory (WM), and whether such effects would be valence dependent. Our experiment was specifically designed to isolate value-based effects on WM from value-based effects on selective attention that might be expected to bias encoding. In a simple associative learning task, participants learned to associate the color of tinted faces with gaining or losing money or neither. Tinted faces then served as memoranda in a face identity WM task for which previously learned color associations were irrelevant and no monetary outcomes were forthcoming. Memory was best for faces with gain-associated tints, poorest for faces with loss-associated tints, and average for faces with no-outcome-associated tints. Value associated with 1 item in the WM array did not modulate memory for other items in the array. Eye movements when studying faces did not depend on the valence of previously learned color associations, arguing against value-based biases being due to differential encoding. This valence-sensitive value-conditioning effect on WM appears to result from modulation of WM maintenance processes. (c) 2015 APA, all rights reserved).

  16. CONDITIONS FOR STABLE CHIP BREAKING AND PROVISION OF MACHINED SURFACE QUALITY WHILE TURNING WITH ASYMMETRIC TOOL VIBRATIONS

    Directory of Open Access Journals (Sweden)

    V. K. Sheleh

    2015-01-01

    Full Text Available The paper considers a process of turning structural steel with asymmetric tool vibrations directed along feeding. Asymmetric vibrations characterized by asymmetry coefficient of vibration cycle, their frequency and amplitude are additionally transferred to the tool in the turning process with the purpose to crush chips. Conditions of stable chip breaking and obtaining optimum dimensions of chip elements have been determined in the paper. In order to reduce a negative impact of the vibration amplitude on a cutting process and quality of the machined surfaces machining must be carried out with its minimum value. In this case certain ratio of the tool vibration frequency to the work-piece rotation speed has been ensured in the paper. A formula has been obtained for calculation of this ratio with due account of the expected length of chip elements and coefficient of vibration cycle asymmetry.Influence of the asymmetric coefficient of the tool vibration cycle on roughness of the machined surfaces and cutting tool wear has been determined in the paper. According to the results pertaining to machining of work-pieces made of 45 and ШХ15 steel the paper presents mathematical relationships of machined surface roughness with cutting modes and asymmetry coefficient of tool vibration cycle. Tool feeding being one of the cutting modes exerts the most significant impact on the roughness value and increase of the tool feeding entails increase in roughness. Reduction in coefficient of vibration cycle asymmetry contributes to surface roughness reduction. However, the cutting tool wear occurs more intensive. Coefficient of the vibration cycle asymmetry must be increased in order to reduce wear rate. Therefore, the choice of the coefficient of the vibration cycle asymmetry is based on the parameters of surface roughness which must be obtained after machining and intensity of tool wear rate.The paper considers a process of turning structural steel with asymmetric

  17. Conceptions of ability as stable and self-evaluative processes: a longitudinal examination.

    Science.gov (United States)

    Pomerantz, E M; Saxon, J L

    2001-01-01

    It has generally been taken for granted that conceiving of ability as stable leads to negative self-evaluative processes, particularly in the face of failure. Yet, a close examination of the empirical findings suggests that the picture may be more complex. In this research, a three-wave longitudinal design spanning 12 months was employed. Older elementary school children (N = 932) indicated their conceptions of academic and social ability as stable to external forces and to internal forces. They also provided information about the importance they place on academic and social competence, their knowledge about academic and social performance, their preference for academic challenge, their perceptions of academic and social competence, and their attributions for academic and social performance. Children's grades in school and their acceptance by peers were obtained as indicators of performance. Over time, conceiving of ability as stable to external forces, particularly in the academic domain, appeared to heighten the importance placed on competence, performance knowledge, preference for challenge, perceptions of competence, and self-enhancing attributions. In contrast, conceptions of ability as stable to internal forces, particularly in the academic domain, appeared to be fostered by placing little importance on competence, a lack of performance knowledge, avoidance of challenge, negative perceptions of competence, self-deprecating attributions, and poor performance.

  18. Using stable isotopes to monitor forms of sulfur during desulfurization processes: A quick screening method

    Science.gov (United States)

    Liu, Chao-Li; Hackley, Keith C.; Coleman, D.D.; Kruse, C.W.

    1987-01-01

    A method using stable isotope ratio analysis to monitor the reactivity of sulfur forms in coal during thermal and chemical desulfurization processes has been developed at the Illinois State Geological Survey. The method is based upon the fact that a significant difference exists in some coals between the 34S/32S ratios of the pyritic and organic sulfur. A screening method for determining the suitability of coal samples for use in isotope ratio analysis is described. Making these special coals available from coal sample programs would assist research groups in sorting out the complex sulfur chemistry which accompanies thermal and chemical processing of high sulfur coals. ?? 1987.

  19. Titanium stable isotope investigation of magmatic processes on the Earth and Moon

    Science.gov (United States)

    Millet, Marc-Alban; Dauphas, Nicolas; Greber, Nicolas D.; Burton, Kevin W.; Dale, Chris W.; Debret, Baptiste; Macpherson, Colin G.; Nowell, Geoffrey M.; Williams, Helen M.

    2016-09-01

    We present titanium stable isotope measurements of terrestrial magmatic samples and lunar mare basalts with the aims of constraining the composition of the lunar and terrestrial mantles and evaluating the potential of Ti stable isotopes for understanding magmatic processes. Relative to the OL-Ti isotope standard, the δ49Ti values of terrestrial samples vary from -0.05 to +0.55‰, whereas those of lunar mare basalts vary from -0.01 to +0.03‰ (the precisions of the double spike Ti isotope measurements are ca. ±0.02‰ at 95% confidence). The Ti stable isotope compositions of differentiated terrestrial magmas define a well-defined positive correlation with SiO2 content, which appears to result from the fractional crystallisation of Ti-bearing oxides with an inferred isotope fractionation factor of ΔTi49oxide-melt = - 0.23 ‰ ×106 /T2. Primitive terrestrial basalts show no resolvable Ti isotope variations and display similar values to mantle-derived samples (peridotite and serpentinites), indicating that partial melting does not fractionate Ti stable isotopes and that the Earth's mantle has a homogeneous δ49Ti composition of +0.005 ± 0.005 (95% c.i., n = 29). Eclogites also display similar Ti stable isotope compositions, suggesting that Ti is immobile during dehydration of subducted oceanic lithosphere. Lunar basalts have variable δ49Ti values; low-Ti mare basalts have δ49Ti values similar to that of the bulk silicate Earth (BSE) while high-Ti lunar basalts display small enrichment in the heavy Ti isotopes. This is best interpreted in terms of source heterogeneity resulting from Ti stable isotope fractionation associated with ilmenite-melt equilibrium during the generation of the mantle source of high-Ti lunar mare basalts. The similarity in δ49Ti between terrestrial samples and low-Ti lunar basalts provides strong evidence that the Earth and Moon have identical stable Ti isotope compositions.

  20. Areal-averaged trace gas emission rates from long-range open-path measurements in stable boundary layer conditions

    Directory of Open Access Journals (Sweden)

    K. Schäfer

    2012-07-01

    Full Text Available Measurements of land-surface emission rates of greenhouse and other gases at large spatial scales (10 000 m2 are needed to assess the spatial distribution of emissions. This can be readily done using spatial-integrating micro-meteorological methods like flux-gradient methods which were evaluated for determining land-surface emission rates of trace gases under stable boundary layers. Non-intrusive path-integrating measurements are utilized. Successful application of a flux-gradient method requires confidence in the gradients of trace gas concentration and wind, and in the applicability of boundary-layer turbulence theory; consequently the procedures to qualify measurements that can be used to determine the flux is critical. While there is relatively high confidence in flux measurements made under unstable atmospheres with mean winds greater than 1 m s−1, there is greater uncertainty in flux measurements made under free convective or stable conditions. The study of N2O emissions of flat grassland and NH3 emissions from a cattle lagoon involves quality-assured determinations of fluxes under low wind, stable or night-time atmospheric conditions when the continuous "steady-state" turbulence of the surface boundary layer breaks down and the layer has intermittent turbulence. Results indicate that following the Monin-Obukhov similarity theory (MOST flux-gradient methods that assume a log-linear profile of the wind speed and concentration gradient incorrectly determine vertical profiles and thus flux in the stable boundary layer. An alternative approach is considered on the basis of turbulent diffusivity, i.e. the measured friction velocity as well as height gradients of horizontal wind speeds and concentrations without MOST correction for stability. It is shown that this is the most accurate of the flux-gradient methods under stable conditions.

  1. Discrete Green's Theorem, Green's Functions and Stable Radiative FDTD Boundary Conditions

    NARCIS (Netherlands)

    Arnold, J.M.; Hon, de B.P.

    2007-01-01

    We propose a radiative boundary condition for the discrete-grid formulation of Helmholtz’ equation, based on rational approximation in the frequency domain of a Green’s function for the discretised system. This boundary condition is free from instabilities.

  2. Polymer Solar Cells – Non Toxic Processing and Stable Polymer Photovoltaic Materials

    DEFF Research Database (Denmark)

    Søndergaard, Roar

    The field of polymer solar cell has experienced enormous progress in the previous years, with efficiencies of small scale devices (~1 mm2) now exceeding 8%. However, if the polymer solar cell is to achieve success as a renewable energy resource, mass production of sufficiently stable and efficient...... and development of more stable materials. The field of polymer solar cells has evolved around the use of toxic and carcinogenic solvents like chloroform, benzene, toluene, chlorobenzene, dichlorobenzene and xylene. As large scale production of organic solar cells is envisaged to production volumes corresponding...... synthesis of polymers carrying water coordinating side chains which allow for processing from semi-aqueous solution. A series of different side chains were synthesized and incorporated into the final polymers as thermocleavable tertiary esters. Using a cleavable side chain induces stability to solar cells...

  3. Modeling anomalous diffusion by a subordinated fractional Lévy-stable process

    International Nuclear Information System (INIS)

    Teuerle, Marek; Wyłomańska, Agnieszka; Sikora, Grzegorz

    2013-01-01

    Two phenomena that can be discovered in systems with anomalous diffusion are long-range dependence and trapping events. The first effect concerns events that are arbitrarily distant but still influence each other exceptionally strongly, which is characteristic for anomalous regimes. The second corresponds to the presence of constant values of the underlying process. Motivated by the relatively poor class of models that can cover these two phenomena, we introduce subordinated fractional Lévy-stable motion with tempered stable waiting times. We present in detail its main properties, propose a simulation scheme and give an estimation procedure for its parameters. The last part of the paper is a presentation, via the Monte Carlo approach, of the effectiveness of the estimation of the parameters. (paper)

  4. Gravity Waves and Wind-Farm Efficiency in Neutral and Stable Conditions

    Science.gov (United States)

    Allaerts, Dries; Meyers, Johan

    2018-02-01

    We use large-eddy simulations (LES) to investigate the impact of stable stratification on gravity-wave excitation and energy extraction in a large wind farm. To this end, the development of an equilibrium conventionally neutral boundary layer into a stable boundary layer over a period of 8 h is considered, using two different cooling rates. We find that turbulence decay has considerable influence on the energy extraction at the beginning of the boundary-layer transition, but afterwards, energy extraction is dominated by geometrical and jet effects induced by an inertial oscillation. It is further shown that the inertial oscillation enhances gravity-wave excitation. By comparing LES results with a simple one-dimensional model, we show that this is related to an interplay between wind-farm drag, variations in the Froude number and the dispersive effects of vertically-propagating gravity waves. We further find that the pressure gradients induced by gravity waves lead to significant upstream flow deceleration, reducing the average turbine output compared to a turbine in isolated operation. This leads us to the definition of a non-local wind-farm efficiency, next to a more standard wind-farm wake efficiency, and we show that both can be of the same order of magnitude. Finally, an energy flux analysis is performed to further elucidate the effect of gravity waves on the flow in the wind farm.

  5. Generation of a severe convective ionospheric storm under stable Rayleigh–Taylor conditions: triggering by meteors?

    Directory of Open Access Journals (Sweden)

    M. C. Kelley

    2016-02-01

    Full Text Available Here we report on four events detected using the Jicamarca Radio Observatory (JRO over an 18-year period, in which huge convective ionospheric storms (CISs occur in a stable ionosphere. We argue that these rare events could be initiated by meteor-induced electric fields. The meteor-induced electric fields map to the bottomside of the F region, causing radar echoes and a localized CIS. If and when a localized disturbance reaches 500 km, we argue that it becomes two-dimensionally turbulent and cascades structure to both large and small scales. This leads to long-lasting structure and, almost certainly, to scintillations over a huge range of latitudes some ±15° wide and to 3 m irregularities, which backscatter the VHF radar waves. These structures located at high altitudes are supported by vortices shed by the upwelling bubble in a vortex street.

  6. Air-stable, solution-processed oxide p-n heterojunction ultraviolet photodetector.

    Science.gov (United States)

    Kim, Do Young; Ryu, Jiho; Manders, Jesse; Lee, Jaewoong; So, Franky

    2014-02-12

    Air-stable solution processed all-inorganic p-n heterojunction ultraviolet photodetector is fabricated with a high gain (EQE, 25 300%). Solution-processed NiO and ZnO films are used as p-type and n-type ultraviolet sensitizing materials, respectively. The high gain in the detector is due to the interfacial trap-induced charge injection that occurs at the ITO/NiO interface by photogenerated holes trapped in the NiO film. The gain of the detector is controlled by the post-annealing temperature of the solution-processed NiO films, which are studied by X-ray photoelectron spectroscopy (XPS).

  7. Conditional Granger Causality of Diffusion Processes

    Czech Academy of Sciences Publication Activity Database

    Wahl, B.; Feudel, U.; Hlinka, Jaroslav; Wächter, M.; Peinke, J.; Freund, J.A.

    2017-01-01

    Roč. 90, č. 10 (2017), č. článku 197. ISSN 1434-6028 R&D Projects: GA ČR GA13-23940S; GA MZd(CZ) NV15-29835A Institutional support: RVO:67985807 Keywords : Granger causality * stochastic process * diffusion process * nonlinear dynamical systems Subject RIV: BB - Applied Statistics, Operational Research OBOR OECD: Computer sciences, information science, bioinformathics (hardware development to be 2.2, social aspect to be 5.8) Impact factor: 1.461, year: 2016

  8. In-liquid Plasma. A stable light source for advanced oxidation processes in environmental remediation

    Science.gov (United States)

    Tsuchida, Akihiro; Shimamura, Takeshi; Sawada, Seiya; Sato, Susumu; Serpone, Nick; Horikoshi, Satoshi

    2018-06-01

    A microwave-inspired device that generates stable in-liquid plasma (LP) in aqueous media and emits narrow light emission lines at 280-320 nm, 660 nm and 780 nm is examined as a light source capable of driving photochemical reactions and advanced oxidation processes in wastewater treatments. The microwave-driven lighting efficiency was improved by decompressing the inside of the reaction vessel, which resulted in lowering the incident power of the microwaves and suppressed the deterioration of the microwave irradiation antenna. This protocol made it possible to generate continuous stable plasma in water. Evaluation of the LP device was carried out by revisiting the decomposition of 1,4-dioxane in aqueous media against the use of such other conventional water treatment processes as (i) UV irradiation alone, (ii) TiO2-assisted photocatalysis with UV irradiation (UV/TiO2), (iii) oxidation with sodium hypochlorite (NaClO), and (iv) UV-assisted decomposition in the presence of NaClO (UV/NaClO). The in-liquid plasma technique proved superior to these four other methods. The influence of pH on the LP protocol was ascertained through experiments in acidified (HCl and H2SO4) and alkaline (NaOH and KOH) aqueous media. Except for H2SO4, decomposition of 1,4-dioxane was enhanced in both acidic and alkaline media.

  9. Standard test method for determination of resistance to stable crack extension under low-constraint conditions

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2006-01-01

    1.1 This standard covers the determination of the resistance to stable crack extension in metallic materials in terms of the critical crack-tip-opening angle (CTOAc), ψc and/or the crack-opening displacement (COD), δ5 resistance curve (1). This method applies specifically to fatigue pre-cracked specimens that exhibit low constraint (crack-length-to-thickness and un-cracked ligament-to-thickness ratios greater than or equal to 4) and that are tested under slowly increasing remote applied displacement. The recommended specimens are the compact-tension, C(T), and middle-crack-tension, M(T), specimens. The fracture resistance determined in accordance with this standard is measured as ψc (critical CTOA value) and/or δ5 (critical COD resistance curve) as a function of crack extension. Both fracture resistance parameters are characterized using either a single-specimen or multiple-specimen procedures. These fracture quantities are determined under the opening mode (Mode I) of loading. Influences of environment a...

  10. The effect of glaze on the quality of frozen stored Alaska pollack (Theragra chalcogramma fillets under stable and unstable conditions

    Directory of Open Access Journals (Sweden)

    Peter Žoldoš

    2011-01-01

    Full Text Available Frozen fillets (n = 288 of Alaska pollack (Theragra chalcogramma were used to evaluate the effect of glaze on lipid oxidation and microbiological indicators during 6 months of freezing storage under stable (−18 °C and unstable temperature (varying from −5 to −18 °C conditions. The amount of glaze, moisture, fat and protein content were measured. Despite the low fat content in Alaska pollack, a positive effect of glazing and stable freezing conditions of storage on the range of oxidative changes of lipids expressed as thiobarbituric acid reactive substances was found. Total counts of viable cells slightly rose before the end of the storage period in both groups with commercially glazed fish. The average counts of psychrotrophs in each group ( were at the same level, ranging from 9.1 ×103 CFU·g-1 to 1.1 × 104 CFU·g-1. According to the microbiological results fillets stored under unstable conditions were considered to be acceptable, but sensory evaluation showed that at the end of frozen storage they could not be consumed because of rancidity. Based on our results, glaze application ranged from 10 to 15% guarantee of final quality, however, prevention of temperature fluctuation during storage is important to keep the quality of the frozen fillets. This is the first similar study in Alaska pollack.

  11. A novel condition for stable nonlinear sampled-data models using higher-order discretized approximations with zero dynamics.

    Science.gov (United States)

    Zeng, Cheng; Liang, Shan; Xiang, Shuwen

    2017-05-01

    Continuous-time systems are usually modelled by the form of ordinary differential equations arising from physical laws. However, the use of these models in practice and utilizing, analyzing or transmitting these data from such systems must first invariably be discretized. More importantly, for digital control of a continuous-time nonlinear system, a good sampled-data model is required. This paper investigates the new consistency condition which is weaker than the previous similar results presented. Moreover, given the stability of the high-order approximate model with stable zero dynamics, the novel condition presented stabilizes the exact sampled-data model of the nonlinear system for sufficiently small sampling periods. An insightful interpretation of the obtained results can be made in terms of the stable sampling zero dynamics, and the new consistency condition is surprisingly associated with the relative degree of the nonlinear continuous-time system. Our controller design, based on the higher-order approximate discretized model, extends the existing methods which mainly deal with the Euler approximation. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

  12. Can common measures of core stability distinguish performance in a shoulder pressing task under stable and unstable conditions?

    Science.gov (United States)

    Keogh, Justin W L; Aickin, Sam E; Oldham, Anthony R H

    2010-02-01

    The primary purpose of this study was to determine whether a range of static core stability (CS) measures could distinguish shoulder press performance in unstable vs. stable conditions. Thirty resistance-trained men gave informed consent to participate in this study. One-repetition maximum strength (from 0.90), moderate (0.85 Core stability training (with or without a SB) may therefore only lead to significant improvements in functional dynamic performance if the postures, mode and velocity of contraction performed in training, are similar to the competitive tasks.

  13. Stable engraftment of human microbiota into mice with a single oral gavage following antibiotic conditioning.

    Science.gov (United States)

    Staley, Christopher; Kaiser, Thomas; Beura, Lalit K; Hamilton, Matthew J; Weingarden, Alexa R; Bobr, Aleh; Kang, Johnthomas; Masopust, David; Sadowsky, Michael J; Khoruts, Alexander

    2017-08-01

    Human microbiota-associated (HMA) animal models relying on germ-free recipient mice are being used to study the relationship between intestinal microbiota and human disease. However, transfer of microbiota into germ-free animals also triggers global developmental changes in the recipient intestine, which can mask disease-specific attributes of the donor material. Therefore, a simple model of replacing microbiota into a developmentally mature intestinal environment remains highly desirable. Here we report on the development of a sequential, three-course antibiotic conditioning regimen that allows sustained engraftment of intestinal microorganisms following a single oral gavage with human donor microbiota. SourceTracker, a Bayesian, OTU-based algorithm, indicated that 59.3 ± 3.0% of the fecal bacterial communities in treated mice were attributable to the donor source. This overall degree of microbiota engraftment was similar in mice conditioned with antibiotics and germ-free mice. Limited surveys of systemic and mucosal immune sites did not show evidence of immune activation following introduction of human microbiota. The antibiotic treatment protocol described here followed by a single gavage of human microbiota may provide a useful, complimentary HMA model to that established in germ-free facilities. The model has the potential for further in-depth translational investigations of microbiota in a variety of human disease states.

  14. High-order Composite Likelihood Inference for Max-Stable Distributions and Processes

    KAUST Repository

    Castruccio, Stefano; Huser, Raphaë l; Genton, Marc G.

    2015-01-01

    In multivariate or spatial extremes, inference for max-stable processes observed at a large collection of locations is a very challenging problem in computational statistics, and current approaches typically rely on less expensive composite likelihoods constructed from small subsets of data. In this work, we explore the limits of modern state-of-the-art computational facilities to perform full likelihood inference and to efficiently evaluate high-order composite likelihoods. With extensive simulations, we assess the loss of information of composite likelihood estimators with respect to a full likelihood approach for some widely-used multivariate or spatial extreme models, we discuss how to choose composite likelihood truncation to improve the efficiency, and we also provide recommendations for practitioners. This article has supplementary material online.

  15. High-order Composite Likelihood Inference for Max-Stable Distributions and Processes

    KAUST Repository

    Castruccio, Stefano

    2015-09-29

    In multivariate or spatial extremes, inference for max-stable processes observed at a large collection of locations is a very challenging problem in computational statistics, and current approaches typically rely on less expensive composite likelihoods constructed from small subsets of data. In this work, we explore the limits of modern state-of-the-art computational facilities to perform full likelihood inference and to efficiently evaluate high-order composite likelihoods. With extensive simulations, we assess the loss of information of composite likelihood estimators with respect to a full likelihood approach for some widely-used multivariate or spatial extreme models, we discuss how to choose composite likelihood truncation to improve the efficiency, and we also provide recommendations for practitioners. This article has supplementary material online.

  16. Supplementary Material for: High-Order Composite Likelihood Inference for Max-Stable Distributions and Processes

    KAUST Repository

    Castruccio, Stefano; Huser, Raphaë l; Genton, Marc G.

    2016-01-01

    In multivariate or spatial extremes, inference for max-stable processes observed at a large collection of points is a very challenging problem and current approaches typically rely on less expensive composite likelihoods constructed from small subsets of data. In this work, we explore the limits of modern state-of-the-art computational facilities to perform full likelihood inference and to efficiently evaluate high-order composite likelihoods. With extensive simulations, we assess the loss of information of composite likelihood estimators with respect to a full likelihood approach for some widely used multivariate or spatial extreme models, we discuss how to choose composite likelihood truncation to improve the efficiency, and we also provide recommendations for practitioners. This article has supplementary material online.

  17. Current techniques for the collection and processing of stable isotope data

    International Nuclear Information System (INIS)

    Goodney, D.E.; Kroopnick, P.M.

    1978-01-01

    Recent innovations in instrumentation for stable isotope mass spectrometry are reviewed. 'Off-line' automatic data collection and 'on-line' processing systems have been developed for use with the Nuclide Integrating Ratiometer (IR-2). A BASIC program detects and corrects most instrumental and operator errors and performs all necessary computations. Analysis of the effects of source gas pressure on the accuracy of delta 18 O measurement showed that our Nuclide 3inch-60 0 instrument has a slope of -1.0 0 / 00 /volt over the normal operating range (10-30V), and our Nuclide 6inch-60 0 instrument has a slope of +0.6 0 / 00 /volt. Use of the IR-2 causes the apparent slopes to change to -1.45 0 / 00 /volt and +5 0 / 00 /volt for the 3inch and 6inch instruments, respectively.(auth.)

  18. Pulsed electric fields for pasteurization: defining processing conditions

    Science.gov (United States)

    Application of pulsed electric fields (PEF) technology in food pasteurization has been extensively studied. Optimal PEF treatment conditions for maximum microbial inactivation depend on multiple factors including PEF processing conditions, production parameters and product properties. In order for...

  19. Detection of non-stationarity in precipitation extremes using a max-stable process model

    Science.gov (United States)

    Westra, S.; Sisson, S.

    2011-12-01

    The question of how extreme precipitation will change under a future climate represents an urgent research problem, not least because of the significant societal impacts that would result from an increase in precipitation-induced flooding. To better constrain future projections, an important line of evidence comes from statistical assessments of change to extreme precipitation in the observational record, as a significant amount of warming since pre-industrial times has already taken place. In this study we address this problem by applying a max-stable process model to evaluate whether extreme precipitation at sub-daily and daily timescales has changed at various locations around Australia. This max-stable process approach, which was developed to simulate spatial fields comprising observations from multiple point locations, significantly increases the precision of a statistical inference compared to standard univariate methods. Applying the technique to a field of annual maxima derived from 30 sub-daily gauges in east Australia from 1965 to 2005, we find a statistically significant increase of 18% for 6-minute rainfall over this period, with smaller increases for longer duration events. We also find an increase of 5.6% and 22.5% per degree of Australian land surface temperature and global sea surface temperature at 6-minute durations, respectively, again with smaller scaling relationships for longer durations. In contrast, limited change could be observed in daily rainfall at most locations, with the exception of a statistically significant decline of 7.4% per degree land surface temperature in southwest Western Australia. These results suggest both the importance of better understanding changes to precipitation at the sub-daily timescale, as well as the need to more precisely simulate temporal variability by accounting for the spatial nature of precipitation in any statistical model.

  20. Characterization and antibacterial properties of stable silver substituted hydroxyapatite nanoparticles synthesized through surfactant assisted microwave process

    Energy Technology Data Exchange (ETDEWEB)

    Iqbal, Nida [Medical Implant Technology Group (MEDITEG), Faculty of Bioscience and Medical Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor Darul Takzim (Malaysia); Abdul Kadir, Mohammed Rafiq, E-mail: rafiq@biomedical.utm.my [Medical Implant Technology Group (MEDITEG), Faculty of Bioscience and Medical Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor Darul Takzim (Malaysia); Nik Malek, Nik Ahmad Nazim [Faculty of Bioscience and Medical Engineering (FBME), Universiti Teknologi Malaysia, 81310 Skudai, Johor Darul Takzim (Malaysia); Mahmood, Nasrul Humaimi Bin [Medical Implant Technology Group (MEDITEG), Faculty of Bioscience and Medical Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor Darul Takzim (Malaysia); Murali, Malliga Raman; Kamarul, T. [Tissue Engineering Group, NOCERAL, Department of Orthopaedic Surgery, Faculty of Medicine, University of Malaya, 50603 Kuala Lumpur (Malaysia)

    2013-09-01

    Highlights: • Stable nano sized silver substitute hydroxyapatite is prepared under surfactant assisted microwave process at 600 W power for 7 min. • The nanoparticles are in the size range of 58–72 nm and exert uniform elongated spheroid morphology. • Increase in silver concentration resulted in better dielectric properties. • Good antibacterial activity and silver release. - Abstract: The present study reports a relatively simple method for the synthesis of stable silver substituted hydroxyapatite nanoparticles with controlled morphology and particle size. In order to achieve this, CTAB is included as a surfactant in the microwave refluxing process (600 W for 7 min). The nanoparticles produced with different silver ion concentrations (0.05, 0.1 and 0.2 wt%) were characterized using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscope (FESEM), energy dispersive X-ray (EDX) and Brunauer–Emmett–Teller (BET) analysis. XRD and FTIR analyses reveal that the Ag-HA nanoparticles were phase pure at 1000 °C. FESEM images showed that the produced nanoparticles are in the size range of 58–72 nm and exert uniform elongated spheroid morphology. The dielectric properties suggest that the increase in dielectric constant (ε′) and dissipation factor (D) values with increasing Ag concentrations. Antibacterial performance of the Ag-HA samples elucidated using disk diffusion technique (DDT) and minimum inhibitory concentration (MIC) demonstrates anti-bacterial activity against Staphylococcus aureus, Bacillus subtilis, Pseudomonas aeruginosa and Escherichia coli. This effect was dose dependent and was more pronounced against Gram-negative bacteria than Gram-positive organisms.

  1. Characterization and antibacterial properties of stable silver substituted hydroxyapatite nanoparticles synthesized through surfactant assisted microwave process

    International Nuclear Information System (INIS)

    Iqbal, Nida; Abdul Kadir, Mohammed Rafiq; Nik Malek, Nik Ahmad Nazim; Mahmood, Nasrul Humaimi Bin; Murali, Malliga Raman; Kamarul, T.

    2013-01-01

    Highlights: • Stable nano sized silver substitute hydroxyapatite is prepared under surfactant assisted microwave process at 600 W power for 7 min. • The nanoparticles are in the size range of 58–72 nm and exert uniform elongated spheroid morphology. • Increase in silver concentration resulted in better dielectric properties. • Good antibacterial activity and silver release. - Abstract: The present study reports a relatively simple method for the synthesis of stable silver substituted hydroxyapatite nanoparticles with controlled morphology and particle size. In order to achieve this, CTAB is included as a surfactant in the microwave refluxing process (600 W for 7 min). The nanoparticles produced with different silver ion concentrations (0.05, 0.1 and 0.2 wt%) were characterized using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscope (FESEM), energy dispersive X-ray (EDX) and Brunauer–Emmett–Teller (BET) analysis. XRD and FTIR analyses reveal that the Ag-HA nanoparticles were phase pure at 1000 °C. FESEM images showed that the produced nanoparticles are in the size range of 58–72 nm and exert uniform elongated spheroid morphology. The dielectric properties suggest that the increase in dielectric constant (ε′) and dissipation factor (D) values with increasing Ag concentrations. Antibacterial performance of the Ag-HA samples elucidated using disk diffusion technique (DDT) and minimum inhibitory concentration (MIC) demonstrates anti-bacterial activity against Staphylococcus aureus, Bacillus subtilis, Pseudomonas aeruginosa and Escherichia coli. This effect was dose dependent and was more pronounced against Gram-negative bacteria than Gram-positive organisms

  2. Source identification of N2O produced during simulated wastewater treatment under different oxygen conditions using stable isotopic analysis

    Directory of Open Access Journals (Sweden)

    T Azzaya

    2014-12-01

    Full Text Available Nitrous oxide (N2O, a potent greenhouse gas which is important in climate change, is predicted to be the most dominant ozone depleting substance. It is mainly produced by oxidation of hydroxylamine (NH2OH or reduction of nitrite (NO2- during microbiological processes such as nitrification and denitrification. Wastewater treatment plant (WWTP is one of the anthropogenic N2O sources because inorganic and organic nitrogen compounds are converted to nitrate (NO3-, in the case of standard system or N2 (in the case of advanced system by bacterial nitrification and denitrification in WWTP. We investigated the N2O production mechanisms during batch experiments that simulate wastewater treatment with activated sludge under various dissolved oxygen (DO concentrations by stable isotope analysis. About 125mL of water was sampled from 30L incubation chamber for several times during the incubation, and concentration and isotopomer ratios of N2O and N-containing species were measured using gas chromatography/isotope ratio mass spectrometry (GC/IRMS. Ammonium (NH4+ consumption was accompanied by increment of nitrite (NO2-, and at the same time dissolved N2O concentration gradually increased to 4850 and 5650 nmol kg-1, respectively, during the four-hour incubation when DO concentrations were 0.2 and 0.5 mg L-1. Observed low SP values (0.2-8.9‰ at DO-0.2 mg L-1, -5.3-6.3‰ at DO-0.5 mg L-1, -1.0-8.3‰ at DO-0.8 mg L-1 in N2O and relationship of nitrogen isotope ratios between N2O and its potential substrates (NH4+, NO3- suggested that N2O produced under the aerobic condition derived mainly from NO2- reduction by ammonia-oxidizing bacteria (nitrifier–denitrification.DOI: http://doi.dx.org/10.5564/mjc.v15i0.313Mongolian Journal of Chemistry  15 (41, 2014, p4-10  

  3. Post-wildfire natural restoration of riparian vegetation under stable hydro-geomorphic conditions: Nahal Grar, Northern Negev Desert, Israel

    Science.gov (United States)

    Egozi, Roey

    2015-04-01

    Wildfires are common to the Mediterranean region due to its defined dry season and long historical anthropogenic activities. Most of post-wildfire studies focus on mountains areas and thus refer to the hill-slope and its physical characteristics, e.g. morphology, length, angles, and aspect; its soil characteristics, e.g. type, infiltration rate, repellency; and its vegetative covers, e.g. planted trees vs. natural forest or native vs. exotic vegetation. In contrary there is very limited literature focusing on ecological and hydro-geomorphic aspects of post-wildfire of riparian vegetation / zone probably because of its negligible burned area relative to the spread of the fire, sometimes, over the whole watershed area. The limited literature on the topic is surprising given the fact that riparian vegetation zone has been acknowledged as a unique and important habitat supporting rich biodiversity. Herein we report on a wildfire event occurred on October 14th 2009 in a river section of Nahal Grar, Northern Negev Desert, Israel. The wildfire although was limited in its area (only 3 hectare) extended over the channel alone from bank to bank and thus provide a unique case study of completely burn down of riparian vegetation, mainly dense stands of Common Red (Australis Phragmites. Therefore a detailed study of this event provides an opportunity to tackle one of the basics questions which is determining the rate of natural restoration process that act at the immediate time after the wildfire event occurred. This type of information is most valuable to professional and stakeholders for better management of post-fire riparian zones. The results of the study suggest that under stable conditions, i.e. no major flood events occurred; disturbance time was short and ranged over 200 days due to, almost, immediate recovery of the riparian vegetation. However the re-growth of the riparian vegetation was not even but rather deferential and more complex then reported in the literature

  4. Generation and monitoring of discrete stable random processes using multiple immigration population models

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, J O; Hopcraft, K I; Jakeman, E [Applied Mathematics Division, School of Mathematical Sciences, University of Nottingham, Nottingham, NG7 2RD (United Kingdom)

    2003-11-21

    Some properties of classical population processes that comprise births, deaths and multiple immigrations are investigated. The rates at which the immigrants arrive can be tailored to produce a population whose steady state fluctuations are described by a pre-selected distribution. Attention is focused on the class of distributions with a discrete stable law, which have power-law tails and whose moments and autocorrelation function do not exist. The separate problem of monitoring and characterizing the fluctuations is studied, analysing the statistics of individuals that leave the population. The fluctuations in the size of the population are transferred to the times between emigrants that form an intermittent time series of events. The emigrants are counted with a detector of finite dynamic range and response time. This is modelled through clipping the time series or saturating it at an arbitrary but finite level, whereupon its moments and correlation properties become finite. Distributions for the time to the first counted event and for the time between events exhibit power-law regimes that are characteristic of the fluctuations in population size. The processes provide analytical models with which properties of complex discrete random phenomena can be explored, and in addition provide generic means by which random time series encompassing a wide range of intermittent and other discrete random behaviour may be generated.

  5. Generation and monitoring of discrete stable random processes using multiple immigration population models

    International Nuclear Information System (INIS)

    Matthews, J O; Hopcraft, K I; Jakeman, E

    2003-01-01

    Some properties of classical population processes that comprise births, deaths and multiple immigrations are investigated. The rates at which the immigrants arrive can be tailored to produce a population whose steady state fluctuations are described by a pre-selected distribution. Attention is focused on the class of distributions with a discrete stable law, which have power-law tails and whose moments and autocorrelation function do not exist. The separate problem of monitoring and characterizing the fluctuations is studied, analysing the statistics of individuals that leave the population. The fluctuations in the size of the population are transferred to the times between emigrants that form an intermittent time series of events. The emigrants are counted with a detector of finite dynamic range and response time. This is modelled through clipping the time series or saturating it at an arbitrary but finite level, whereupon its moments and correlation properties become finite. Distributions for the time to the first counted event and for the time between events exhibit power-law regimes that are characteristic of the fluctuations in population size. The processes provide analytical models with which properties of complex discrete random phenomena can be explored, and in addition provide generic means by which random time series encompassing a wide range of intermittent and other discrete random behaviour may be generated

  6. Designing solution-processable air-stable liquid crystalline crosslinkable semiconductors

    DEFF Research Database (Denmark)

    McCulloch, I.; Bailey, C.; Genevicius, K.

    2006-01-01

    organic light emitting diode displays, low frequency radio frequency identification tag and other low performance electronics. Organic semiconductors that offer both electrical performance and stability with respect to storage and operation under ambient conditions are required. This work describes...... the development of reactive mesogen semiconductors, which form large crosslinked LC domains on polymerization within mesophases. These crosslinked domains offer mechanical stability and are inert to solvent exposure in further processing steps. Reactive mesogens containing conjugated aromatic cores, designed...

  7. Direct stable isotope porewater equilibration and identification of groundwater processes in heterogeneous sedimentary rock

    Energy Technology Data Exchange (ETDEWEB)

    David, Katarina, E-mail: k.david@student.unsw.edu.au [School of Mining Engineering, UNSW Australia, NSW 2052 (Australia); Connected Waters Initiative Research Centre, UNSW Australia, NSW 2052 (Australia); Timms, Wendy [School of Mining Engineering, UNSW Australia, NSW 2052 (Australia); Connected Waters Initiative Research Centre, UNSW Australia, NSW 2052 (Australia); Baker, Andy [Connected Waters Initiative Research Centre, UNSW Australia, NSW 2052 (Australia)

    2015-12-15

    The off-axis integrated cavity output spectrometry (ICOS) method to analyse porewater isotopic composition has been successfully applied over the last decade in groundwater studies. This paper applies the off-axis ICOS method to analyse the porewater isotopic composition, attempts to use the isotopic shift in groundwater values along with simple geochemical mixing model to define the groundwater processes in the Sydney Basin, Australia. Complementary data included geophysical, hydrogeological, geochemical, and mineralogical investigations. Porewater from core samples were analysed for δ{sup 18}O and δ{sup 2}H from various sedimentary units in the Basin and compared to endpoint water members. Stable δ{sup 18}O and δ{sup 2}H values of porewaters in the Basin (− 9.5 to 2.8‰ for δ{sup 18}O and − 41.9 to 7.9‰ for δ{sup 2}H) covered a relatively narrow range in values. The variability in water isotopes reflects the variability of the input signal, which is the synoptic variability in isotopic composition of rainfall, and to a minor extent the subsequent evaporation. The porosity, bulk density and mineralogy data demonstrate the heterogeneity that adds the complexity to variations in the isotope profile with depth. The source of chloride in the sedimentary sequence was related to rock–water and cement/matrix–water interaction rather than to evaporation. The heterogeneous character of the sedimentary rock strata was supported by a change in pore pressures between units, density and variability in rock geochemical analyses obtained by using X-ray fluorescence (XRF) and X-ray power diffraction analyses. This research identified distinct hydrogeological zones in the Basin that were not previously defined by classic hydrogeological investigations. Isotopic signature of porewaters along the detailed vertical profile in combination with mineralogical, geochemical, geophysical and hydrogeological methods can provide useful information on groundwater movement in

  8. The minimum work required for air conditioning process

    International Nuclear Information System (INIS)

    Alhazmy, Majed M.

    2006-01-01

    This paper presents a theoretical analysis based on the second law of thermodynamics to estimate the minimum work required for the air conditioning process. The air conditioning process for hot and humid climates involves reducing air temperature and humidity. In the present analysis the inlet state is the state of the environment which has also been chosen as the dead state. The final state is the human thermal comfort fixed at 20 o C dry bulb temperature and 60% relative humidity. The general air conditioning process is represented by an equivalent path consisting of an isothermal dehumidification followed by a sensible cooling. An exergy analysis is performed on each process separately. Dehumidification is analyzed as a separation process of an ideal mixture of air and water vapor. The variations of the minimum work required for the air conditioning process with the ambient conditions is estimated and the ratio of the work needed for dehumidification to the total work needed to perform the entire process is presented. The effect of small variations in the final conditions on the minimum required work is evaluated. Tolerating a warmer or more humid final condition can be an easy solution to reduce the energy consumptions during critical load periods

  9. Toward stable nickel catalysts for aqueous phase reforming of biomass-derived feedstock under reducing and alkaline conditions

    NARCIS (Netherlands)

    Haasterecht, van T.; Ludding, C.C.I.; Jong, de K.P.; Bitter, J.H.

    2014-01-01

    Nickel nanoparticles supported on carbon nanofibers (CNF) can be stabilized in aqueous phase processes at elevated temperatures and pressures by tuning the reaction conditions to control Ni oxidation and leaching. As a showcase, Ni/CNF was used for the production of hydrogen via aqueous phase

  10. Stability of prebiotic, laminaran oligosaccharide under food processing conditions

    Science.gov (United States)

    Chamidah, A.

    2018-04-01

    Prebiotic stability tests on laminaran oligosaccharide under food processing conditions were urgently performed to determine the ability of prebiotics deal with processing. Laminaran, oligosaccharide is produced from enzymatic hydrolysis. To further apply this prebiotic, it is necessary to test its performance on food processing. Single prebiotic or in combination with probiotic can improve human digestive health. The effectiveness evaluation of prebiotic should be taken into account in regards its chemical and functional stabilities. This study aims to investigate the stability of laminaran, oligosaccharide under food processing condition.

  11. Coupled Environmental Processes in the Mojave Desert and Implications for ET Covers as Stable Landforms

    International Nuclear Information System (INIS)

    Shafer, D.; Young, M.; Zitzer, S.; McDonald, E.; Caldwell, T.

    2006-01-01

    Monolayer evapotranspiration (ET) covers are the baseline method for closure of disposal sites for low-level radioactive waste (LLW), mixed LLW, and transuranic (TRU) waste at the Nevada Test Site (NTS). The regulatory timeline is typically 1,000 years for LLW and 10,000 years for TRU waste. Covers for such waste have different technical considerations than those with shorter timelines because they are subject to environmental change for longer periods of time, and because the environmental processes are often coupled. To evaluate these changes, four analog sites (approximately 30, 1,000 to 2,000, 7,000 to 12,500, and 125,000 years in age) on the NTS were analyzed to address the early post-institutional control period (the youngest site), the 1,000-year compliance period for disposal of LLW, and the 10,000-year period for TRU waste. Tests included soil texture, structure, and morphology; surface soil infiltration and hydraulic conductivity; vegetation and faunal surveys; and literature reviews. Separate measurements were made in plant undercanopy and intercanopy areas. The results showed a progressive increase in silt and clay content of surface soils with age. Changes in soil texture and structure led to a fivefold decline in saturated hydraulic conductivity in intercanopy areas, but no change in undercanopies, which were subject to bioturbation. These changes may have been responsible for the reduction in total plant cover, most dramatically in intercanopy areas, primarily because more precipitation either runs off the site or is held nearer to the surface where plant roots are less common. The results suggest that covers may evolve over longer timeframes to stable landforms that minimize the need for active maintenance

  12. Limiting conditional distributions for birth-death processes

    NARCIS (Netherlands)

    Kijima, M.; Nair, M.G.; Pollett, P.K.; van Doorn, Erik A.

    1997-01-01

    In a recent paper one of us identified all of the quasi-stationary distributions for a non-explosive, evanescent birth-death process for which absorption is certain, and established conditions for the existence of the corresponding limiting conditional distributions. Our purpose is to extend these

  13. Conditional Stochastic Processes Applied to Wave Load Predictions

    DEFF Research Database (Denmark)

    Jensen, Jørgen Juncher

    2015-01-01

    The concept of conditional stochastic processes provides a powerful tool for evaluation and estimation of wave loads on ships and offshore structures. This article first considers conditional waves with a focus on critical wave episodes. Then the inherent uncertainty in the results is illustrated...

  14. Archival processes of the water stable isotope signal in East Antarctic ice cores

    Science.gov (United States)

    Casado, Mathieu; Landais, Amaelle; Picard, Ghislain; Münch, Thomas; Laepple, Thomas; Stenni, Barbara; Dreossi, Giuliano; Ekaykin, Alexey; Arnaud, Laurent; Genthon, Christophe; Touzeau, Alexandra; Masson-Delmotte, Valerie; Jouzel, Jean

    2018-05-01

    The oldest ice core records are obtained from the East Antarctic Plateau. Water isotopes are key proxies to reconstructing past climatic conditions over the ice sheet and at the evaporation source. The accuracy of climate reconstructions depends on knowledge of all processes affecting water vapour, precipitation and snow isotopic compositions. Fractionation processes are well understood and can be integrated in trajectory-based Rayleigh distillation and isotope-enabled climate models. However, a quantitative understanding of processes potentially altering snow isotopic composition after deposition is still missing. In low-accumulation sites, such as those found in East Antarctica, these poorly constrained processes are likely to play a significant role and limit the interpretability of an ice core's isotopic composition. By combining observations of isotopic composition in vapour, precipitation, surface snow and buried snow from Dome C, a deep ice core site on the East Antarctic Plateau, we found indications of a seasonal impact of metamorphism on the surface snow isotopic signal when compared to the initial precipitation. Particularly in summer, exchanges of water molecules between vapour and snow are driven by the diurnal sublimation-condensation cycles. Overall, we observe in between precipitation events modification of the surface snow isotopic composition. Using high-resolution water isotopic composition profiles from snow pits at five Antarctic sites with different accumulation rates, we identified common patterns which cannot be attributed to the seasonal variability of precipitation. These differences in the precipitation, surface snow and buried snow isotopic composition provide evidence of post-deposition processes affecting ice core records in low-accumulation areas.

  15. Distributed automatic control of technological processes in conditions of weightlessness

    Science.gov (United States)

    Kukhtenko, A. I.; Merkulov, V. I.; Samoylenko, Y. I.; Ladikov-Royev, Y. P.

    1986-01-01

    Some problems associated with the automatic control of liquid metal and plasma systems under conditions of weightlessness are examined, with particular reference to the problem of stability of liquid equilibrium configurations. The theoretical fundamentals of automatic control of processes in electrically conducting continuous media are outlined, and means of using electromagnetic fields for simulating technological processes in a space environment are discussed.

  16. Biologic phosphorus elimination - influencing parameters, boundary conditions, process optimation

    International Nuclear Information System (INIS)

    Dai Xiaohu.

    1992-01-01

    This paper first presents a systematic study of the basic process of biologic phosphorus elimination as employed by the original 'Phoredox (Main Stream) Process'. The conditions governing the process and the factors influencing its performance were determined by trial operation. A stationary model was developed for the purpose of modelling biologic phosphorus elimination in such a main stream process and optimising the dimensioning. The validity of the model was confirmed by operational data given in the literature and by operational data from the authors' own semitechnical-scale experimental plant. The model permits simulation of the values to be expected for effluent phosphorus and phosphate concentrations for given influent data and boundary conditions. It is thus possible to dimension a plant for accomodation of the original Phoredox (Main Stream) Process or any similar phosphorus eliminating plant that is to work according to the principle of the main stream process. (orig./EF) [de

  17. Processing counterfactual and hypothetical conditionals: an fMRI investigation.

    Science.gov (United States)

    Kulakova, Eugenia; Aichhorn, Markus; Schurz, Matthias; Kronbichler, Martin; Perner, Josef

    2013-05-15

    Counterfactual thinking is ubiquitous in everyday life and an important aspect of cognition and emotion. Although counterfactual thought has been argued to differ from processing factual or hypothetical information, imaging data which elucidate these differences on a neural level are still scarce. We investigated the neural correlates of processing counterfactual sentences under visual and aural presentation. We compared conditionals in subjunctive mood which explicitly contradicted previously presented facts (i.e. counterfactuals) to conditionals framed in indicative mood which did not contradict factual world knowledge and thus conveyed a hypothetical supposition. Our results show activation in right occipital cortex (cuneus) and right basal ganglia (caudate nucleus) during counterfactual sentence processing. Importantly the occipital activation is not only present under visual presentation but also with purely auditory stimulus presentation, precluding a visual processing artifact. Thus our results can be interpreted as reflecting the fact that counterfactual conditionals pragmatically imply the relevance of keeping in mind both factual and supposed information whereas the hypothetical conditionals imply that real world information is irrelevant for processing the conditional and can be omitted. The need to sustain representations of factual and suppositional events during counterfactual sentence processing requires increased mental imagery and integration efforts. Our findings are compatible with predictions based on mental model theory. Copyright © 2013 Elsevier Inc. All rights reserved.

  18. Comparison of pore water samplers and cryogenic distillation under laboratory and field conditions for soil water stable isotope analysis.

    Science.gov (United States)

    Thoma, Michael; Frentress, Jay; Tagliavini, Massimo; Scandellari, Francesca

    2018-02-15

    We used pore water samplers (PWS) to sample for isotope analysis (1) only water, (2) soil under laboratory conditions, and (3) soil in the field comparing the results with cryogenic extraction (CE). In (1) and (2), no significant differences between source and water extracted with PWS were detected with a mean absolute difference (MAD) always lower than 2 ‰ for δ 2 H and 1 ‰ for δ 18 O. In (2), CE water was more enriched than PWS-extracted water, with a MAD respect to source water of roughly 8 ‰ for δ 2 H and 4 ‰ for δ 18 O. In (3), PWS water was enriched relative to CE water by 3 ‰ for δ 2 H and 0.9 ‰ for δ 18 O. The latter result may be due to the distinct water portions sampled by the two methods. Large pores, easily sampled by PWS, likely retain recent, and enriched, summer precipitation while small pores, only sampled by CE, possibly retain isotopically depleted water from previous winter precipitation or irrigation inputs. Accuracy and precision were greater for PWS relative to CE. PWS is therefore suggested as viable tool to extract soil water for stable isotope analysis, particularly for soils used in this study (sandy and silty loams).

  19. Permafrost hydrology in changing climatic conditions: seasonal variability of stable isotope composition in rivers in discontinuous permafrost

    International Nuclear Information System (INIS)

    Streletskiy, Dmitry A; Shiklomanov, Nikolay I; Nyland, Kelsey E; Tananaev, Nikita I; Opel, Thomas; Streletskaya, Irina D; Tokarev, Igor’; Shiklomanov, Alexandr I

    2015-01-01

    Role of changing climatic conditions on permafrost degradation and hydrology was investigated in the transition zone between the tundra and forest ecotones at the boundary of continuous and discontinuous permafrost of the lower Yenisei River. Three watersheds of various sizes were chosen to represent the characteristics of the regional landscape conditions. Samples of river flow, precipitation, snow cover, and permafrost ground ice were collected over the watersheds to determine isotopic composition of potential sources of water in a river flow over a two year period. Increases in air temperature over the last forty years have resulted in permafrost degradation and a decrease in the seasonal frost which is evident from soil temperature measurements, permafrost and active-layer monitoring, and analysis of satellite imagery. The lowering of the permafrost table has led to an increased storage capacity of permafrost affected soils and a higher contribution of ground water to river discharge during winter months. A progressive decrease in the thickness of the layer of seasonal freezing allows more water storage and pathways for water during the winter low period making winter discharge dependent on the timing and amount of late summer precipitation. There is a substantial seasonal variability of stable isotopic composition of river flow. Spring flooding corresponds to the isotopic composition of snow cover prior to the snowmelt. Isotopic composition of river flow during the summer period follows the variability of precipitation in smaller creeks, while the water flow of larger watersheds is influenced by the secondary evaporation of water temporarily stored in thermokarst lakes and bogs. Late summer precipitation determines the isotopic composition of texture ice within the active layer in tundra landscapes and the seasonal freezing layer in forested landscapes as well as the composition of the water flow during winter months. (letter)

  20. Kinetics of Quality Changes of Pangasius Fillets at Stable and Dynamic Temperatures, Simulating Downstream Cold Chain Conditions

    Directory of Open Access Journals (Sweden)

    Nga Mai

    2017-01-01

    Full Text Available This study was about the quality changes of Pangasius fillets during storage under simulated temperature conditions of downstream cold chain. Sensory, chemical, and microbiological analyses were conducted over storage time and bacterial growth was modelled. Sensory quality index (QI, at five stable (1, 4, 9, 15, and 19 ± 1°C and three dynamic temperatures, progressed faster at higher temperatures, especially with sooner temperature abuses. Total volatile basic nitrogen remained under the acceptable limit throughout all the storage conditions. Total viable psychrotrophic counts (TVC were around 5.68 ± 0.24 log CFU g−1 at the beginning and exceeded the limit of 6 log CFU g−1 after 216, 96, 36, 16, and 7 h at 1, 4, 9, 15, and 19 ± 1°C, respectively. Meanwhile, Pseudomonas counts started at 3.81 ± 0.53 log CFU g−1 and reached 4.60–6.36 log CFU g−1 by the time of TVC rejection. Since lower shelf lives were given by TVC rather than QI, it should be appropriate to base the product shelf life on the TVC acceptable limit. Kinetics models based on the Baranyi and Roberts and square root models, developed for TVC and Pseudomonas spp., gave acceptable bacterial estimations at dynamic temperatures, with over 80% of observed counts within the acceptable simulation zone, revealing promising model applicability as a supporting tool for cold chain management. However, further improvement and validation of the models are needed.

  1. An integrated condition-monitoring method for a milling process using reduced decomposition features

    International Nuclear Information System (INIS)

    Liu, Jie; Wu, Bo; Hu, Youmin; Wang, Yan

    2017-01-01

    Complex and non-stationary cutting chatter affects productivity and quality in the milling process. Developing an effective condition-monitoring approach is critical to accurately identify cutting chatter. In this paper, an integrated condition-monitoring method is proposed, where reduced features are used to efficiently recognize and classify machine states in the milling process. In the proposed method, vibration signals are decomposed into multiple modes with variational mode decomposition, and Shannon power spectral entropy is calculated to extract features from the decomposed signals. Principal component analysis is adopted to reduce feature size and computational cost. With the extracted feature information, the probabilistic neural network model is used to recognize and classify the machine states, including stable, transition, and chatter states. Experimental studies are conducted, and results show that the proposed method can effectively detect cutting chatter during different milling operation conditions. This monitoring method is also efficient enough to satisfy fast machine state recognition and classification. (paper)

  2. The effect of two different housing conditions on the welfare of young horses stabled for the first time

    NARCIS (Netherlands)

    Visser, E.K.; Ellis, A.D.; Reenen, van C.G.

    2008-01-01

    The effect of stabling for the first time on the behaviour and welfare of young and naïve horses has not yet been studied in detail. In this study we examined the effect of two typical housing systems on their subsequent behavioural and physiological responses upon first time stabling. Thirty-six

  3. First Passage Time for Tempered Stable Process and Its Application to Perpetual American Option and Barrier Option Pricing

    OpenAIRE

    Kim, Young Shin

    2018-01-01

    In this paper, we will discuss an approximation of the characteristic function of the first passage time for a Levy process using the martingale approach. The characteristic function of the first passage time of the tempered stable process is provided explicitly or by an indirect numerical method. This will be applied to the perpetual American option pricing and the barrier option pricing. Numerical illustrations are provided for the calibrated parameters using the market call and put prices.

  4. Evaluation of advanced hot conditioning process for PHWRS

    International Nuclear Information System (INIS)

    Chandramohan, P.; Srinivasan, M.P.; Velmurugan, S.

    2015-01-01

    Hot-conditioning/hot functional test process is carried out to the PHT system of reactor before reactor going to critical/operational. The process is aimed in checking the component functionalities at high temperature and high pressure conditions, the process also checks/removes the suspended corrosion products in heat transport circuit. This process leads to formation of a passive or corrosion oxide film on the heat transport circuit surfaces which protects/mitigates the corrosion of the system circuits during the operation of plant. Major concerned alloy in the Primary Heat Transport (PHT) system of Indian PHWRs during the hot conditioning process and also during operation is the carbon steel due to its high corrosion. Hot-conditioning process mitigates the corrosion of carbon steel by the formation of iron oxide (Fe 3 O 4 ) as major oxide phase layer on the carbon steel surface with a typical thickness of 1.0 μm with particle size of 1μm after 336 h of process at 250 °C. But this passive oxide film thickness increase with time of operation of system with c.a. 10μm for 2.2 EFYP. The protectiveness of passive layer can be further enhanced by reducing the particle sizes in the passive film to nano meter range. The process can impact on the compactness of passive oxide layer with reduced pores in the oxide layer and properties of the nano nature oxide (transport properties) impacting the corrosion mitigation. The corrosion mitigation reduce the source term in the activated corrosion product generation. To achieve this a new process 'Advanced hot conditioning' was developed in water steam chemistry division, BARC for getting a passive oxide film with a lowered particle size in the passive film. The AHC process with 1g/L of PEG-8000 at 250 °C for 336 h showed a particle size <100 nm. The process was tested under the normal operating conditions as function of the time, the corrosion parameter like oxide film thickness, corrosion rate and metal ion

  5. Experimental and numerical study of atmospheric turbulence and dispersion in stable conditions and in near field at a complex site

    International Nuclear Information System (INIS)

    Wei, Xiao

    2016-01-01

    An experimental program has been designed in order to study pollutants dispersion at a complex site with a focus on stable conditions, which are still challenging for numerical modelling. This experimental program is being conducted at the SIRTA site in a southern suburb of Paris and consists in measuring, in near field, the turbulence and the pollutants dispersion. The aim of this program is to characterize the fine structure of turbulence and associated dispersion through high temporal and spatial resolution measurements. Then, these measurements allow to validate and improve the performance of CFD simulation for turbulence and dispersion in a heterogeneous field. The instrumental set up includes 12 ultrasonic anemometers measuring continuously wind velocity and temperature at 10 Hz, and 6 photo-ionization detectors (PIDs) measuring gas concentration at 50 Hz during tracer tests. Intensive observations periods (IOPs) with gas releases have been performed since March 2012. First of all, a detailed study of flow on the site is made, because it must be characterised and properly simulated before attempting to simulate the pollutants dispersion. This study is based on two years of continuous measurements and on measurements performed during IOPs. Turbulence strong anisotropy in the surface layer is characterized by calculating variances, integral length scales and power spectra of the three wind velocity components. Propagation of turbulent structures between sensors has been characterized with velocity correlations. Energy spectra show several slopes in different frequency regions. Also, data analyses show impact of terrain heterogeneity on the measurements. The forest to the north of the experimental field modifies wind velocity and direction for a large northerly sector. It induces a strong directional wind shear and a wind deceleration below the forest height. Numerical simulations are carried out using the CFD code, Code-Saturne, in RANS mode with a standard k

  6. Utilizing Stable Isotopes and Isotopic Anomalies to Study Early Solar System Formation Processes

    Science.gov (United States)

    Simon, Justin

    2017-01-01

    Chondritic meteorites contain a diversity of particle components, i.e., chondrules and calcium-, aluminum-rich refractory inclusions (CAIs), that have survived since the formation of the Solar System. The chemical and isotopic compositions of these materials provide a record of the conditions present in the protoplanetary disk where they formed and can aid our understanding of the processes and reservoirs in which solids formed in the solar nebula, an important step leading to the accretion of planetesimals. Isotopic anomalies associated with nucleosynthetic processes are observed in these discrete materials, and can be compared to astronomical observations and astrophysical formation models of stars and more recently proplyds. The existence and size of these isotopic anomalies are typically thought to reflect a significant state of isotopic heterogeneity in the earliest Solar System, likely left over from molecular cloud heterogeneities on the grain scale, but some could also be due to late stellar injection. The homogenization of these isotopic anomalies towards planetary values can be used to track the efficiency and timescales of disk wide mixing,

  7. Predicting speech intelligibility in conditions with nonlinearly processed noisy speech

    DEFF Research Database (Denmark)

    Jørgensen, Søren; Dau, Torsten

    2013-01-01

    The speech-based envelope power spectrum model (sEPSM; [1]) was proposed in order to overcome the limitations of the classical speech transmission index (STI) and speech intelligibility index (SII). The sEPSM applies the signal-tonoise ratio in the envelope domain (SNRenv), which was demonstrated...... to successfully predict speech intelligibility in conditions with nonlinearly processed noisy speech, such as processing with spectral subtraction. Moreover, a multiresolution version (mr-sEPSM) was demonstrated to account for speech intelligibility in various conditions with stationary and fluctuating...

  8. Conditions and constraints of food processing in space

    Science.gov (United States)

    Fu, B.; Nelson, P. E.; Mitchell, C. A. (Principal Investigator)

    1994-01-01

    Requirements and constraints of food processing in space include a balanced diet, food variety, stability for storage, hardware weight and volume, plant performance, build-up of microorganisms, and waste processing. Lunar, Martian, and space station environmental conditions include variations in atmosphere, day length, temperature, gravity, magnetic field, and radiation environment. Weightlessness affects fluid behavior, heat transfer, and mass transfer. Concerns about microbial behavior include survival on Martian and lunar surfaces and in enclosed environments. Many present technologies can be adapted to meet space conditions.

  9. Experimental and numerical study of atmospheric turbulence and dispersion in stable conditions and in near field at a complex site

    International Nuclear Information System (INIS)

    Wei, Xiao

    2016-01-01

    An experimental program has been designed in order to study pollutants dispersion at a complex site with a focus on stable conditions, which are still challenging for numerical modelling. This experimental program is being conducted at the SIRTA site in a southern suburb of Paris and consists in measuring, in near field, the turbulence and the pollutants dispersion. The aim of this program is to characterize the fine structure of turbulence and associated dispersion through high temporal and spatial resolution measurements. Then, these measurements allow to validate and improve the performance of CFD simulation for turbulence and dispersion in a heterogeneous field. The instrumental set up includes 12 ultrasonic anemometers measuring continuously wind velocity and temperature at 10 Hz, and 6 photo-ionization detectors (PIDs) measuring gas concentration at 50 Hz during tracer tests. Intensive observations periods (IOPs) with gas releases have been performed since March 2012.First of all, a detailed study of flow on the site is made, because it must be characterised and properly simulated before attempting to simulate the pollutants dispersion. This study is based on two years of continuous measurements and on measurements performed during IOPs. Turbulence strong anisotropy in the surface layer is characterized by calculating variances, integral length scales and power spectra of the three wind velocity components. Propagation of turbulent structures between sensors has been characterized with velocity correlations. Energy spectra show several slopes in different frequency regions. Also, data analyses show impact of terrain heterogeneity on the measurements. The forest to the north of experimental field modifies wind velocity and direction for a large northerly sector. It induces a strong directional wind shear and a wind deceleration below the forest height. Numerical simulations are carried out using the CFD code Code-Saturne in RANS mode with a standard κ

  10. Amino acid stable isotope applications to deep-sea corals: A molecular geochemistry approach to reconstructing past ocean conditions

    Science.gov (United States)

    McMahon, K.; McCarthy, M. D.; Guilderson, T. P.; Sherwood, O.; Williams, B.; Larsen, T.; Glynn, D. S.

    2017-12-01

    Future climate change is predicted to alter ocean productivity, food web dynamics, biogeochemical cycling, and the efficacy of the biological pump. Proteinaceous deep-sea corals act as "living sediment traps," providing long-term, high-resolution records of exported surface ocean production and a window into past changes in ocean condition as a historical context for potential future changes. Here, we present recent work developing the application of compound-specific stable isotope analysis of individual amino acids to proteinaceous deep-sea corals to reconstruct past changes in phytoplankton community composition and biogeochemical cycling. We present new calibrations for molecular isotope comparisons between metabolically active coral polyp tissue and bioarchival proteinaceous skeleton. We then applied these techniques to deep-sea corals from the North Pacific Subtropical Gyre (NPSG) to reconstruct centennial to millennial time scale changes in phytoplankton community composition and biogeochemical cycling as a function of regional climate change. This work suggests that the NPSG has undergone multiple major phytoplankton regime shifts over the last millennium between prokaryotic and eukaryotic phytoplankton communities and associated sources of nitrogen fueling production. The most recent regime, which started around the end of the Little Ice Age and the onset of the Industrial era, is unprecedented in the last 1000 years and resulted in a 30-50% increase in diazotrophic cyanobacteria contribution to export production and an associated 17-27% increase in N2-fixation in the NPSG over last century. By offering the first direct phylogenetic context for long-term shifts in isotopic records of exported particulate organic matter, our data represent a major step forward in understanding the evolution of marine plankton community dynamics, food web architecture, biogeochemical cycling, and the climate feedback loops through the biological pump.

  11. Surface Passivation for 3-5 Semiconductor Processing: Stable Gallium Sulphide Films by MOCVD

    Science.gov (United States)

    Macinnes, Andrew N.; Jenkins, Phillip P.; Power, Michael B.; Kang, Soon; Barron, Andrew R.; Hepp, Aloysius F.; Tabib-Azar, Massood

    1994-01-01

    Gallium sulphide (GaS) has been deposited on GaAs to form stable, insulating, passivating layers. Spectrally resolved photoluminescence and surface recombination velocity measurements indicate that the GaS itself can contribute a significant fraction of the photoluminescence in GaS/GaAs structures. Determination of surface recombination velocity by photoluminescence is therefore difficult. By using C-V analysis of metal-insulator-semiconductor structures, passivation of the GaAs with GaS films is quantified.

  12. Preparation process of a stable non radioactive carrier intended for radiodiagnosis

    International Nuclear Information System (INIS)

    Molinski, V.J.; Wilczewski, J.A.

    1976-01-01

    The description is given of a stable non radioactive carrier with a pH of around 2 and around 4, for cardiological studies, exploring the blood in circulation and exploring the brain, after labelling with sup(99m)Tc. It includes human serum albumin (SAH) and stannous tartrate, the proportion in weight between the SAH and stannous tartrate being between around 50:1 and around 150:1 [fr

  13. Process Formulations And Curing Conditions That Affect Saltstone Properties

    Energy Technology Data Exchange (ETDEWEB)

    Reigel, M. M.; Pickenheim, B. R.; Daniel, W. E.

    2012-09-28

    The first objective of this study was to analyze saltstone fresh properties to determine the feasibility of reducing the formulation water to premix (w/p) ratio while varying the amount of extra water and admixtures used during processing at the Saltstone Production Facility (SPF). The second part of this study was to provide information for understanding the impact of curing conditions (cure temperature, relative humidity (RH)) and processing formulation on the performance properties of cured saltstone.

  14. Optimizing access to conditions data in ATLAS event data processing

    CERN Document Server

    Rinaldi, Lorenzo; The ATLAS collaboration

    2018-01-01

    The processing of ATLAS event data requires access to conditions data which is stored in database systems. This data includes, for example alignment, calibration, and configuration information that may be characterized by large volumes, diverse content, and/or information which evolves over time as refinements are made in those conditions. Additional layers of complexity are added by the need to provide this information across the world-wide ATLAS computing grid and the sheer number of simultaneously executing processes on the grid, each demanding a unique set of conditions to proceed. Distributing this data to all the processes that require it in an efficient manner has proven to be an increasing challenge with the growing needs and number of event-wise tasks. In this presentation, we briefly describe the systems in which we have collected information about the use of conditions in event data processing. We then proceed to explain how this information has been used to refine not only reconstruction software ...

  15. Effect of processing conditions on shrinkage in injection moulding

    NARCIS (Netherlands)

    Jansen, K.M.B.; van Dijk, D.J.; Husselman, M.H.

    1998-01-01

    A systematic study on the effect of processing conditions on mold shrinkage was undertaken for seven common thermoplastic polymers. It turned out that the holding pressure was always the key parameter. The effect of the melt temperature is slightly less important. Injection velocity and mold

  16. Clarification process: Resolution of decision-problem conditions

    Science.gov (United States)

    Dieterly, D. L.

    1980-01-01

    A model of a general process which occurs in both decisionmaking and problem-solving tasks is presented. It is called the clarification model and is highly dependent on information flow. The model addresses the possible constraints of individual indifferences and experience in achieving success in resolving decision-problem conditions. As indicated, the application of the clarification process model is only necessary for certain classes of the basic decision-problem condition. With less complex decision problem conditions, certain phases of the model may be omitted. The model may be applied across a wide range of decision problem conditions. The model consists of two major components: (1) the five-phase prescriptive sequence (based on previous approaches to both concepts) and (2) the information manipulation function (which draws upon current ideas in the areas of information processing, computer programming, memory, and thinking). The two components are linked together to provide a structure that assists in understanding the process of resolving problems and making decisions.

  17. Eye Movement Analysis of Information Processing under Different Testing Conditions.

    Science.gov (United States)

    Dillon, Ronna F.

    1985-01-01

    Undergraduates were given complex figural analogies items, and eye movements were observed under three types of feedback: (1) elaborate feedback; (2) subjects verbalized their thinking and application of rules; and (3) no feedback. Both feedback conditions enhanced the rule-governed information processing during inductive reasoning. (Author/GDC)

  18. Working conditions in the European meat processing industry

    NARCIS (Netherlands)

    Nossent, S.; Groot, B. de; Verschuren, R.

    1995-01-01

    This report reflects the main results of one part of the study 'Monitoring the work environment at sectorial level'. This part regards the meat processing industry in Europe. In this study, which was a project of the European Foundation for Living and Working Conditions, ten member states of the

  19. Modifying yeast tolerance to inhibitory conditions of ethanol production processes

    Directory of Open Access Journals (Sweden)

    Luis eCaspeta

    2015-11-01

    Full Text Available Saccharomyces cerevisiae strains having a broad range of substrate utilization, rapid substrate consumption and conversion to ethanol, as well as good tolerance to inhibitory conditions are ideal for cost-competitive ethanol production from lignocellulose. A major drawback to directly design S. cerevisiae tolerance to inhibitory conditions of lignocellulosic ethanol production processes is the lack of knowledge about basic aspects of its cellular signaling network in response to stress. Here we highlight the inhibitory conditions found in ethanol production processes, the targeted cellular functions, the key contributions of integrated –omics analysis to reveal cellular stress responses according to these inhibitors, and current status on design-based engineering of tolerant and efficient S. cerevisiae strains for ethanol production from lignocellulose.

  20. Modifying Yeast Tolerance to Inhibitory Conditions of Ethanol Production Processes

    DEFF Research Database (Denmark)

    Caspeta, Luis; Castillo, Tania; Nielsen, Jens

    2015-01-01

    Saccharomyces cerevisiae strains having a broad range of substrate utilization, rapid substrate consumption, and conversion to ethanol, as well as good tolerance to inhibitory conditions are ideal for cost-competitive ethanol production from lignocellulose. A major drawback to directly design S....... cerevisiae tolerance to inhibitory conditions of lignocellulosic ethanol production processes is the lack of knowledge about basic aspects of its cellular signaling network in response to stress. Here, we highlight the inhibitory conditions found in ethanol production processes, the targeted cellular...... functions, the key contributions of integrated -omics analysis to reveal cellular stress responses according to these inhibitors, and current status on design-based engineering of tolerant and efficient S. cerevisiae strains for ethanol production from lignocellulose....

  1. Mashing of Rice with Barley Malt Under Nonconventional Process Conditions for Use in Food Processes

    DEFF Research Database (Denmark)

    Moe, T.; Adler-Nissen, Jens

    1994-01-01

    Non-conventional mashing conditions are relevant in the development of a lactic acid-fermented soymilk beverage where mashed rice is the source of carbohydrates for the fermentation and sweetness of the beverage. Advantages in the process layout could be achieved by mashing at higher pH and lower...... conditions when a mashing step is integrated in other food processes....

  2. Development of safe and shelf-stable Intermediate Moisture (IM) convenience meat products through radiation processing

    International Nuclear Information System (INIS)

    Ramesh Chander; Kanatt, S.R.; Chawla, S.P.; Bongirwar, D.R.

    2001-01-01

    Ready-to-use shelf stable mutton and chicken sheek kababs, and chicken chilly were developed by reducing the water activity either by grilling or by hot air drying, vacuum packing and irradiation. Microbiological analysis revealed a dose dependent reduction in total viable count and in Staphylococcus species on irradiation treatment ( 2.5, 5.0 and 10.0 kGy). The products subjected to irradiation at 10 kGy showed absence of viable micro-organisms and also had high sensory acceptability up to 9 months at ambient temperature. (author)

  3. Influence of cycle number, temperature and manufacturing process on deformation-induced martensite in meta-stable austenitic stainless steels

    International Nuclear Information System (INIS)

    Kalkhof, D.; Niffenegger, M.; Grosse, M.; Bart, G.

    2002-01-01

    During cyclic loading of austenitic stainless steel, microstructural changes occur, which affect both the mechanical and the physical properties. Typical features are the rearrangement of dislocations and, in some cases, a deformation-induced martensitic phase transformation. In our investigation martensite formation was used as an indication for material degradation due to fatigue. Knowledge about mechanisms and influencing parameters of the martensitic transformation process is essential for the application in a lifetime monitoring system. The investigations showed that for a given meta-stable austenitic stainless steel the deformation-induced martensite depends on the applied strain amplitude, the cycle number (accumulated plastic strain) and the temperature. It was demonstrated that the volume fraction of martensite continuously increases with the cycle number. Therefore, martensite content could be used for indication of the fatigue usage. According to the Coffin-Manson relation the dependence of the martensite content on the cycle number could be described with a power law. The exponent was determined to be equal to 0.5 for the applied loading and temperature conditions. The influence of temperature on deformation-induced martensite was considered by means of a thermodynamic relation. Furthermore, the initial material state (initial defect density) played an important role for the martensite formation rate. Material properties and microstructures were characterised by metallography, neutron diffraction, and advanced magnetic non-destructive techniques. In order to investigate the correlation between the martensite content in the austenitic matrix and magnetic properties, the magnetic susceptibility was determined. Furthermore, a high sensitive Giant Magneto Resistant sensor was used to visualize the martensite distribution at the surface of the fatigue specimens. All applied techniques, neutron diffraction and advanced magnetic methods allowed the detection

  4. Stabilization process in Saccharomyces intra and interspecific hybrids in fermentative conditions.

    Science.gov (United States)

    Pérez-Través, Laura; Lopes, Christian A; Barrio, Eladio; Querol, Amparo

    2014-12-01

    We evaluated the genetic stabilization of artificial intra- (Saccharomyces cerevisiae) and interspecific (S. cerevisiae × S. kudriavzevii) hybrids under wine fermentative conditions. Large-scale transitions in genome size and genome reorganizations were observed during this process. Interspecific hybrids seem to need fewer generations to reach genetic stability than intraspecific hybrids. The largest number of molecular patterns recovered among the derived clones was observed for intraspecific hybrids, particularly for those obtained by rare-mating. Molecular marker analyses revealed that unstable clones could change during the industrial process to obtain active dry yeast. When no changes in molecular markers and ploidy were observed after this process, no changes in genetic composition were confirmed by comparative genome hybridization, considering the clone as a stable hybrid. According to our results, under these conditions, fermentation steps 3 and 5 (30-50 generations) would suffice to obtain genetically stable interspecific and intraspecific hybrids, respectively. Copyright© by the Spanish Society for Microbiology and Institute for Catalan Studies.

  5. Process for processing and conditioning radioactive effluents of low and medium activity

    International Nuclear Information System (INIS)

    Taponier, Jean; Pierlas, Rene.

    1979-01-01

    Preferably continuous process for processing radioactive effluents of low and medium activity, comprising an effluent pre-treatment: precipitation of radioactive compounds to form a stable suspension that can be concentrated. Then a mix is made of 0.6 to 2 parts of cement by weight for one part by weight of suspension, from 0.5 to 5% by weight, in relation to the cement, of asbestos fibre and, if necessary, added water for the cement to set, this suspension containing from 15 to 75% by weight of dry extract and a suspension agent. The homogeneous mix achieved is poured into a container [fr

  6. Electrostatic powder spraying process for the fabrication of stable superhydrophobic surfaces

    Science.gov (United States)

    Gu, Guotuan; Tian, Yuping; Li, Zhantie; Lu, Dongfang

    2011-03-01

    Nano-sized Al2O3 particles were modified by heptadecafluorodecyl trimethoxysilane and 2,3-epoxy propoxy propyl trimethoxysilicane to make it both hydrophobic and reactive. The reactive nano-particles were mixed with polyester resin containing curing agents and electrostatic sprayed on stainless steel substrates to obtain stable superhydrophobic coatings after curing. The water contact angle (WCA) on the hybrid coating is influenced by the content of Al2O3 particles in the coating. As the Al2O3 concentration in the coating was increased from 0% to 8%, WCA increased from 68° to 165°. Surface topography of the coatings was examined using scanning electron microscopy (SEM). Nano-particles covered on the coating surface formed continuous film with greatly enhanced roughness, which was found to be responsible for the superhydrophobicity. The method is simple and cost effective and can be used for preparing self-cleaning superhydrophobic coating on large areas.

  7. Electrostatic powder spraying process for the fabrication of stable superhydrophobic surfaces

    International Nuclear Information System (INIS)

    Gu Guotuan; Tian Yuping; Li Zhantie; Lu Dongfang

    2011-01-01

    Nano-sized Al 2 O 3 particles were modified by heptadecafluorodecyl trimethoxysilane and 2,3-epoxy propoxy propyl trimethoxysilicane to make it both hydrophobic and reactive. The reactive nano-particles were mixed with polyester resin containing curing agents and electrostatic sprayed on stainless steel substrates to obtain stable superhydrophobic coatings after curing. The water contact angle (WCA) on the hybrid coating is influenced by the content of Al 2 O 3 particles in the coating. As the Al 2 O 3 concentration in the coating was increased from 0% to 8%, WCA increased from 68 o to 165 o . Surface topography of the coatings was examined using scanning electron microscopy (SEM). Nano-particles covered on the coating surface formed continuous film with greatly enhanced roughness, which was found to be responsible for the superhydrophobicity. The method is simple and cost effective and can be used for preparing self-cleaning superhydrophobic coating on large areas.

  8. Smelting Associated with the Advanced Spent Fuel Conditioning Process

    International Nuclear Information System (INIS)

    Hur, J-M.; Jeong, M-S.; Lee, W-K.; Cho, S-H.; Seo, C-S.; Park, S-W.

    2004-01-01

    The smelting process associated with the advanced spent fuel conditioning process (ACP) of Korea Atomic Energy Research Institute was studied by using surrogate materials. Considering the vaporization behaviors of input materials, the operation procedure of smelting was set up as (1) removal of residual salts, (2) melting of metal powder, and (3) removal of dross from a metal ingot. The behaviors of porous MgO crucible during smelting were tested and the chemical stability of MgO in the salt-being atmosphere was confirmed

  9. A statistical approach to define some tofu processing conditions

    Directory of Open Access Journals (Sweden)

    Vera de Toledo Benassi

    2011-12-01

    Full Text Available The aim of this work was to make tofu from soybean cultivar BRS 267 under different processing conditions in order to evaluate the influence of each treatment on the product quality. A fractional factorial 2(5-1 design was used, in which independent variables (thermal treatment, coagulant concentration, coagulation time, curd cutting, and draining time were tested at two different levels. The response variables studied were hardness, yield, total solids, and protein content of tofu. Polynomial models were generated for each response. To obtain tofu with desirable characteristics (hardness ~4 N, yield 306 g tofu.100 g-1 soybeans, 12 g proteins.100 g-1 tofu and 22 g solids.100 g-1 tofu, the following processing conditions were selected: heating until boiling plus 10 minutes in water bath, 2% dihydrated CaSO4 w/w, 10 minutes coagulation, curd cutting, and 30 minutes draining time.

  10. Effect of Corbrin Capsule combined with routine western medicine on the airway remodeling process in patients with stable COPD

    Directory of Open Access Journals (Sweden)

    Su-Li Song

    2017-08-01

    Full Text Available Objective: To explore the effect of Corbrin Capsule combined with routine western medicine on the airway remodeling process in patients with stable COPD. Methods: A total of 120 patients with stable COPD who were treated in the hospital between May 2014 and December 2016 were collected and divided into control group and observation group according to the random number table method, 60 cases in each group. The control group received routine western medicine treatment, and the observation group received Corbrin Capsule combined with routine western medicine treatment. The differences in serum levels of inflammatory factors, growth factors and fibrosis indexes were compared between the two groups before and after treatment. Results: Before treatment, difference in serum levels of inflammatory factors, growth factors and fibrosis indexes were not statistically significant between the two groups of patients. After 8 weeks of treatment, serum IL-2, IL-4, IL-8, IL-18, VEGF, b-FGF, NGF, LN, HA, PⅢNP and C-Ⅳ levels of both groups of patients were significantly lower than those before treatment, and serum IL-2, IL-4, IL-8, IL-18, VEGF, b-FGF, NGF, LN, HA, PⅢNP and C-Ⅳ levels of observation group were lower than those of control group. Conclusion: Corbrin Capsule combined with routine western medicine treatment can effectively inhibit the fibrosis process in patients with stable COPD.

  11. Penitentiary Resocialization – three conditionings of the process

    Directory of Open Access Journals (Sweden)

    Henryk Machel

    2011-12-01

    Full Text Available Penitentiary resocialization, its form, content, organization and effectiveness depends on many conditionings. Among the most important are: the penitentiary system which makes the general decisions, conditions characteristic for the particular penitentiary, including social conditions of the prison and the human material (convicts’ community which as a subject are both within the scope of interest of those conducting the resocialization and are included in the penitentiary treatment. The goal of this treatment is to yield the expected effectiveness of resocialization. That is why the penitentiary system which is the most important to produce the expected effect has to take many conditionings under consideration and, foremost, factors characteristic for the particular penitentiary and the human material (convicts’ community which is the subject of penitentiary treatment. As many research show the nature of the penitentiary doesn’t work in favour of the process of resocialization. The interaction of conflict, the subculture of the penitentiary and other factors, including troubles of penitentiary isolation, often occurring disorders between the prisoner and his family or his close relatives amount to the reduction in the influence of the resocialization. Another of the three important conditionings described here that stymie the process are certain categories of prisoners. The subject in question are the ones addicted to alcohol and drugs, showing non-psychotic personality disorders, psychopaths and those connected with organized crime, kidnappers, assassins and hit-men and terrorists. Separate category of convicts who are hard to resocialize are those convicted of sexual offences, including paedophiles. So far no effective psycho-correction methods have been formed, especially for paedophiles. Certain difficulties are also experienced when dealing with long-term convicts: sentenced for 25 years or lifetime – sometimes it is not clear

  12. The role of proteolytic processing and the stable signal peptide in expression of the Old World arenavirus envelope glycoprotein ectodomain

    International Nuclear Information System (INIS)

    Burri, Dominique J.; Pasquato, Antonella; Ramos da Palma, Joel; Igonet, Sebastien; Oldstone, Michael B.A.; Kunz, Stefan

    2013-01-01

    Maturation of the arenavirus GP precursor (GPC) involves proteolytic processing by cellular signal peptidase and the proprotein convertase subtilisin kexin isozyme 1 (SKI-1)/site 1 protease (S1P), yielding a tripartite complex comprised of a stable signal peptide (SSP), the receptor-binding GP1, and the fusion-active transmembrane GP2. Here we investigated the roles of SKI-1/S1P processing and SSP in the biosynthesis of the recombinant GP ectodomains of lymphocytic choriomeningitis virus (LCMV) and Lassa virus (LASV). When expressed in mammalian cells, the LCMV and LASV GP ectodomains underwent processing by SKI-1/S1P, followed by dissociation of GP1 from GP2. The GP2 ectodomain spontaneously formed trimers as revealed by chemical cross-linking. The endogenous SSP, known to be crucial for maturation and transport of full-length arenavirus GPC was dispensable for processing and secretion of the soluble GP ectodomain, suggesting a specific role of SSP in the stable prefusion conformation and transport of full-length GPC.

  13. The role of proteolytic processing and the stable signal peptide in expression of the Old World arenavirus envelope glycoprotein ectodomain

    Energy Technology Data Exchange (ETDEWEB)

    Burri, Dominique J.; Pasquato, Antonella; Ramos da Palma, Joel [Institute of Microbiology, University Hospital Center and University of Lausanne, Lausanne CH-1011 (Switzerland); Igonet, Sebastien; Oldstone, Michael B.A. [Department of Immunology and Microbial Science, The Scripps Research Institute, La Jolla, CA 92037 (United States); Kunz, Stefan, E-mail: Stefan.Kunz@chuv.ch [Institute of Microbiology, University Hospital Center and University of Lausanne, Lausanne CH-1011 (Switzerland)

    2013-02-05

    Maturation of the arenavirus GP precursor (GPC) involves proteolytic processing by cellular signal peptidase and the proprotein convertase subtilisin kexin isozyme 1 (SKI-1)/site 1 protease (S1P), yielding a tripartite complex comprised of a stable signal peptide (SSP), the receptor-binding GP1, and the fusion-active transmembrane GP2. Here we investigated the roles of SKI-1/S1P processing and SSP in the biosynthesis of the recombinant GP ectodomains of lymphocytic choriomeningitis virus (LCMV) and Lassa virus (LASV). When expressed in mammalian cells, the LCMV and LASV GP ectodomains underwent processing by SKI-1/S1P, followed by dissociation of GP1 from GP2. The GP2 ectodomain spontaneously formed trimers as revealed by chemical cross-linking. The endogenous SSP, known to be crucial for maturation and transport of full-length arenavirus GPC was dispensable for processing and secretion of the soluble GP ectodomain, suggesting a specific role of SSP in the stable prefusion conformation and transport of full-length GPC.

  14. Flux behaviour under different operational conditions in osmosis process

    DEFF Research Database (Denmark)

    Korenak, Jasmina; Zarebska, Agata; Buksek, Hermina

    the active membrane layer is facing draw solution. Osmosis process can be affected by several factors, such as operating conditions (temperature and cross flow velocity), feed and draw solution properties, and membrane characteristics. These factors can significantly contribute to the efficiency......, and total dissolved solids. Taken together our results can contribute understanding of the how performance of asymmetric FO membranes can be enhanced by feed and draw properties, membrane characteristics and operational conditions.......The transport of water molecules across a semi-permeable membrane is driven by the osmotic pressure difference between feed and draw solution. Two different operational modes can be distinguished, namely FO mode when the active membrane layer is facing the wastewater (feed), and PRO mode when...

  15. Testing and modelling autoregressive conditional heteroskedasticity of streamflow processes

    Directory of Open Access Journals (Sweden)

    W. Wang

    2005-01-01

    Full Text Available Conventional streamflow models operate under the assumption of constant variance or season-dependent variances (e.g. ARMA (AutoRegressive Moving Average models for deseasonalized streamflow series and PARMA (Periodic AutoRegressive Moving Average models for seasonal streamflow series. However, with McLeod-Li test and Engle's Lagrange Multiplier test, clear evidences are found for the existence of autoregressive conditional heteroskedasticity (i.e. the ARCH (AutoRegressive Conditional Heteroskedasticity effect, a nonlinear phenomenon of the variance behaviour, in the residual series from linear models fitted to daily and monthly streamflow processes of the upper Yellow River, China. It is shown that the major cause of the ARCH effect is the seasonal variation in variance of the residual series. However, while the seasonal variation in variance can fully explain the ARCH effect for monthly streamflow, it is only a partial explanation for daily flow. It is also shown that while the periodic autoregressive moving average model is adequate in modelling monthly flows, no model is adequate in modelling daily streamflow processes because none of the conventional time series models takes the seasonal variation in variance, as well as the ARCH effect in the residuals, into account. Therefore, an ARMA-GARCH (Generalized AutoRegressive Conditional Heteroskedasticity error model is proposed to capture the ARCH effect present in daily streamflow series, as well as to preserve seasonal variation in variance in the residuals. The ARMA-GARCH error model combines an ARMA model for modelling the mean behaviour and a GARCH model for modelling the variance behaviour of the residuals from the ARMA model. Since the GARCH model is not followed widely in statistical hydrology, the work can be a useful addition in terms of statistical modelling of daily streamflow processes for the hydrological community.

  16. Data acquisition and quantitative analysis of stable hydrogen isotope in liquid and gas in the liquid phase catalytic exchange process

    International Nuclear Information System (INIS)

    Choi, H. J.; Lee, H. S.; Kim, K. R.; Cheong, H. S.; Ahn, D. H.; Lee, S. H.; Paek, S. W.; Kang, H. S.; Kim, J. G.

    2001-01-01

    A pilot plant for the Liquid Phase Catalytic Exchange process was built and has been operating to test the hydrophobic catalyst developed to remove the tritium generated at the CANDU nuclear power plants. The methods of quantitative analysis of hydrogen stable isotope were compared. Infrared spectroscopy was used for the liquid samples, and gas chromatography with hydrogen carrier gas showed the best result for gas samples. Also, a data acquisition system was developed to record the operation parameters. This record was very useful to investigate the causes of the system trip

  17. Self-similarly evolving and minimally dissipated stable states of plasmas realized after relaxation and self-organization processes

    International Nuclear Information System (INIS)

    Kondoh, Yoshiomi; Hakoiwa, Toru; Okada, Akihito; Kobayashi, Naohiro; Takahashi, Toshiki

    2006-01-01

    A novel set of simultaneous eigenvalue equations having dissipative terms are derived to find self-similarly evolving and minimally dissipated stable states of plasmas realized after relaxation and self-organization processes. By numerically solving the set of eigenvalue equations in a cylindrical model, typical spatial profiles of plasma parameters, electric and magnetic fields and diffusion factors are presented, all of which determine self-consistently with each other by physical laws and mutual relations among them, just as in experimental plasmas. (author)

  18. Structural analysis of advanced spent fuel conditioning process

    International Nuclear Information System (INIS)

    Gu, J. H.; Jung, W. M.; Jo, I. J.; Gug, D. H.; Yoo, K. S.

    2003-01-01

    An advanced spent fuel conditioning process (ACP) is developing for the safe and effective management of spent fuels which arising from the domestic nuclear power plants. And its demonstration facility is under design. This facility will be prepared by modifying IMEF's reserve hot cell facility which reserved for future usage by considering the characteristics of ACP. This study presents a basic structural architecture design and analysis results of ACP hot cell including modification of the IMEF. The results of this study will be used for the detail design of ACP demonstration facility, and utilized as basic data for the licensing of the ACP facility

  19. Radiation Monitoring System in Advanced Spent Fuel Conditioning Process Facility

    Energy Technology Data Exchange (ETDEWEB)

    You, Gil Sung; Kook, D. H.; Choung, W. M.; Ku, J. H.; Cho, I. J.; You, G. S.; Kwon, K. C.; Lee, W. K.; Lee, E. P

    2006-09-15

    The Advanced spent fuel Conditioning Process is under development for effective management of spent fuel by converting UO{sub 2} into U-metal. For demonstration of this process, {alpha}-{gamma} type new hot cell was built in the IMEF basement . To secure against radiation hazard, this facility needs radiation monitoring system which will observe the entire operating area before the hot cell and service area at back of it. This system consists of 7 parts; Area Monitor for {gamma}-ray, Room Air Monitor for particulate and iodine in both area, Hot cell Monitor for hot cell inside high radiation and rear door interlock, Duct Monitor for particulate of outlet ventilation, Iodine Monitor for iodine of outlet duct, CCTV for watching workers and material movement, Server for management of whole monitoring system. After installation and test of this, radiation monitoring system will be expected to assist the successful ACP demonstration.

  20. Radiation Monitoring System in Advanced Spent Fuel Conditioning Process Facility

    International Nuclear Information System (INIS)

    You, Gil Sung; Kook, D. H.; Choung, W. M.; Ku, J. H.; Cho, I. J.; You, G. S.; Kwon, K. C.; Lee, W. K.; Lee, E. P.

    2006-09-01

    The Advanced spent fuel Conditioning Process is under development for effective management of spent fuel by converting UO 2 into U-metal. For demonstration of this process, α-γ type new hot cell was built in the IMEF basement . To secure against radiation hazard, this facility needs radiation monitoring system which will observe the entire operating area before the hot cell and service area at back of it. This system consists of 7 parts; Area Monitor for γ-ray, Room Air Monitor for particulate and iodine in both area, Hot cell Monitor for hot cell inside high radiation and rear door interlock, Duct Monitor for particulate of outlet ventilation, Iodine Monitor for iodine of outlet duct, CCTV for watching workers and material movement, Server for management of whole monitoring system. After installation and test of this, radiation monitoring system will be expected to assist the successful ACP demonstration

  1. Uses of stable isotopes

    International Nuclear Information System (INIS)

    Axente, Damian

    1998-01-01

    The most important fields of stable isotope use with examples are presented. These are: 1. Isotope dilution analysis: trace analysis, measurements of volumes and masses; 2. Stable isotopes as tracers: transport phenomena, environmental studies, agricultural research, authentication of products and objects, archaeometry, studies of reaction mechanisms, structure and function determination of complex biological entities, studies of metabolism, breath test for diagnostic; 3. Isotope equilibrium effects: measurement of equilibrium effects, investigation of equilibrium conditions, mechanism of drug action, study of natural processes, water cycle, temperature measurements; 4. Stable isotope for advanced nuclear reactors: uranium nitride with 15 N as nuclear fuel, 157 Gd for reactor control. In spite of some difficulties of stable isotope use, particularly related to the analytical techniques, which are slow and expensive, the number of papers reporting on this subject is steadily growing as well as the number of scientific meetings organized by International Isotope Section and IAEA, Gordon Conferences, and regional meeting in Germany, France, etc. Stable isotope application development on large scale is determined by improving their production technologies as well as those of labeled compound and the analytical techniques. (author)

  2. Medial prefrontal cortex stimulation modulates the processing of conditioned fear

    Directory of Open Access Journals (Sweden)

    Anne eGuhn

    2014-02-01

    Full Text Available The extinction of conditioned fear is dependent on an efficient interplay between the amygdala and the medial prefrontal cortex (mPFC. In rats, high-frequency electrical mPFC stimulation was shown to improve extinction by a reduction of amygdala activity. However, so far it is unclear whether stimulation of homologues regions in humans might have similar beneficial effects.Healthy volunteers received one-session of either active or sham repetitive transcranial magnetic stimulation (rTMS covering the mPFC while undergoing a two-day fear conditioning and extinction paradigm. rTMS was applied offline after fear acquisition in which one of two faces (CS+ but not CS- was associated with an aversive scream (UCS. Immediate extinction learning (day 1 and extinction recall (day 2 were conducted without UCS delivery. Conditioned responses were assessed in a multimodal approach using fear-potentiated startle (FPS, skin conductance responses (SCR, functional near-infrared spectroscopy (fNIRS and self-report scales. Consistent with the hypothesis of a modulated processing of conditioned fear after high-frequency rTMS, the active group showed a reduced CS+/CS- discrimination during extinction learning as evident in FPS as well as in SCR and arousal ratings. FPS responses to CS+ further showed a linear decrement throughout both extinction sessions. This study describes the first experimental approach of influencing conditioned fear by using rTMS which can be a basis for future studies investigating a complementation of mPFC stimulation to cognitive behavioral therapy.

  3. All-solution processed polymer light-emitting diodes with air stable metal-oxide electrodes

    NARCIS (Netherlands)

    Bruyn, P. de; Moet, D.J.D.; Blom, P.W.M.

    2012-01-01

    We present an all-solution processed polymer light-emitting diode (PLED) using spincoated zinc oxide (ZnO) and vanadium pentoxide (V2O5) as electron and hole injecting contact, respectively. We compare the performance of these devices to the standard PLED design using PEDOT:PSS as anode and Ba/Al as

  4. SPITZER survey of dust grain processing in stable discs around binary post-AGB stars

    NARCIS (Netherlands)

    Gielen, C.; van Winckel, H.; Min, M.; Waters, L.B.F.M.; Lloyd Evans, T.

    2008-01-01

    Aims. We investigate the mineralogy and dust processing in the circumbinary discs of binary post-AGB stars using high-resolution TIMMI2 and SPITZER infrared spectra. Methods: We perform a full spectral fitting to the infrared spectra using the most recent opacities of amorphous and crystalline dust

  5. Batch-batch stable microbial community in the traditional fermentation process of huyumei broad bean pastes.

    Science.gov (United States)

    Zhu, Linjiang; Fan, Zihao; Kuai, Hui; Li, Qi

    2017-09-01

    During natural fermentation processes, a characteristic microbial community structure (MCS) is naturally formed, and it is interesting to know about its batch-batch stability. This issue was explored in a traditional semi-solid-state fermentation process of huyumei, a Chinese broad bean paste product. The results showed that this MCS mainly contained four aerobic Bacillus species (8 log CFU per g), including B. subtilis, B. amyloliquefaciens, B. methylotrophicus, and B. tequilensis, and the facultative anaerobe B. cereus with a low concentration (4 log CFU per g), besides a very small amount of the yeast Zygosaccharomyces rouxii (2 log CFU per g). The dynamic change of the MCS in the brine fermentation process showed that the abundance of dominant species varied within a small range, and in the beginning of process the growth of lactic acid bacteria was inhibited and Staphylococcus spp. lost its viability. Also, the MCS and its dynamic change were proved to be highly reproducible among seven batches of fermentation. Therefore, the MCS naturally and stably forms between different batches of the traditional semi-solid-state fermentation of huyumei. Revealing microbial community structure and its batch-batch stability is helpful for understanding the mechanisms of community formation and flavour production in a traditional fermentation. This issue in a traditional semi-solid-state fermentation of huyumei broad bean paste was firstly explored. This fermentation process was revealed to be dominated by a high concentration of four aerobic species of Bacillus, a low concentration of B. cereus and a small amount of Zygosaccharomyces rouxii. Lactic acid bacteria and Staphylococcus spp. lost its viability at the beginning of fermentation. Such the community structure was proved to be highly reproducible among seven batches. © 2017 The Society for Applied Microbiology.

  6. Stable Isolation of Phycocyanin from Spirulina platensis Associated with High-Pressure Extraction Process

    Directory of Open Access Journals (Sweden)

    Kyung-Hwan Jung

    2013-01-01

    Full Text Available A method for stably purifying a functional dye, phycocyanin from Spirulina platensis was developed by a hexane extraction process combined with high pressure. This was necessary because this dye is known to be very unstable during normal extraction processes. The purification yield of this method was estimated as 10.2%, whose value is 3%–5% higher than is the case from another conventional separation method using phosphate buffer. The isolated phycocyanin from this process also showed the highest purity of 0.909 based on absorbance of 2.104 at 280 nm and 1.912 at 620 nm. Two subunits of phycocyanin namely α-phycocyanin (18.4 kDa and β-phycocyanin (21.3 kDa were found to remain from the original mixtures after being extracted, based on SDS-PAGE analysis, clearly demonstrating that this process can stably extract phycocyanin and is not affected by extraction solvent, temperature, etc. The stability of the extracted phycocyanin was also confirmed by comparing its DPPH (α,α-diphenyl-β-picrylhydrazyl scavenging activity, showing 83% removal of oxygen free radicals. This activity was about 15% higher than that of commercially available standard phycocyanin, which implies that the combined extraction method can yield relatively intact chromoprotein through absence of degradation. The results were achieved because the low temperature and high pressure extraction effectively disrupted the cell membrane of Spirulina platensis and degraded less the polypeptide subunits of phycocyanin (which is a temperature/pH-sensitive chromoprotein as well as increasing the extraction yield.

  7. Development of shelf-stable radiation processed Ready-to-Cook (RTC) Indian vegetables

    International Nuclear Information System (INIS)

    Sharma, J.; Chatterjee, S.; Gupta, S.; Kumar, Vivekanand; Variyar, P.S.; Sharma, A.

    2009-01-01

    Use of radiation processing in combination with packaging and low temperature storage aided in extending shelf-life of RTC Indian vegetables without affecting their organoleptic and sensory quality. An extension in shelf-life of 15 days in case of RTC french beans and pumpkin and in RTC ash gourd and drumstick of 8 and 5 days respectively was achieved when cling wrapped, irradiated at a dose of 2 kGy and stored at 10 deg C. (author)

  8. Efficient and stable solution-processed planar perovskite solar cells via contact passivation

    KAUST Repository

    Tan, Hairen; Jain, Ankit; Voznyy, Oleksandr; Lan, Xinzheng; Garcí a de Arquer, F. Pelayo; Fan, James Z.; Quintero-Bermudez, Rafael; Yuan, Mingjian; Zhang, Bo; Zhao, Yicheng; Fan, Fengjia; Li, Peicheng; Quan, Li Na; Zhao, Yongbiao; Lu, Zheng-Hong; Yang, Zhenyu; Hoogland, Sjoerd; Sargent, Edward H.

    2017-01-01

    Planar perovskite solar cells (PSCs) made entirely via solution processing at low temperatures (<150°C) offer promise for simple manufacturing, compatibility with flexible substrates, and perovskite-based tandem devices. However, these PSCs require an electron-selective layer that performs well with similar processing. We report a contact-passivation strategy using chlorine-capped TiO2 colloidal nanocrystal film that mitigates interfacial recombination and improves interface binding in low-temperature planar solar cells. We fabricated solar cells with certified efficiencies of 20.1 and 19.5% for active areas of 0.049 and 1.1 square centimeters, respectively, achieved via low-temperature solution processing. Solar cells with efficiency greater than 20% retained 90% (97% after dark recovery) of their initial performance after 500 hours of continuous room-temperature operation at their maximum power point under 1-sun illumination (where 1 sun is defined as the standard illumination at AM1.5, or 1 kilowatt/square meter).

  9. Processed Meat Protein and Heat-Stable Peptide Marker Identification Using Microwave-Assisted Tryptic Digestion

    Directory of Open Access Journals (Sweden)

    Magdalena Montowska

    2016-01-01

    Full Text Available New approaches to rapid examination of proteins and peptides in complex food matrices are of great interest to the community of food scientists. The aim of the study is to examine the influence of microwave irradiation on the acceleration of enzymatic cleavage and enzymatic digestion of denatured proteins in cooked meat of five species (cattle, horse, pig, chicken and turkey and processed meat products (coarsely minced, smoked, cooked and semi-dried sausages. Severe protein aggregation occurred not only in heated meat under harsh treatment at 190 °C but also in processed meat products. All the protein aggregates were thoroughly hydrolyzed aft er 1 h of trypsin treatment with short exposure times of 40 and 20 s to microwave irradiation at 138 and 303 W. There were much more missed cleavage sites observed in all microwave-assisted digestions. Despite the incompleteness of microwave-assisted digestion, six unique peptide markers were detected, which allowed unambiguous identification of processed meat derived from the examined species. Although the microwave-assisted tryptic digestion can serve as a tool for rapid and high-throughput protein identification, great caution and pre-evaluation of individual samples is recommended in protein quantitation.

  10. Efficient and stable solution-processed planar perovskite solar cells via contact passivation

    KAUST Repository

    Tan, Hairen

    2017-02-03

    Planar perovskite solar cells (PSCs) made entirely via solution processing at low temperatures (<150°C) offer promise for simple manufacturing, compatibility with flexible substrates, and perovskite-based tandem devices. However, these PSCs require an electron-selective layer that performs well with similar processing. We report a contact-passivation strategy using chlorine-capped TiO2 colloidal nanocrystal film that mitigates interfacial recombination and improves interface binding in low-temperature planar solar cells. We fabricated solar cells with certified efficiencies of 20.1 and 19.5% for active areas of 0.049 and 1.1 square centimeters, respectively, achieved via low-temperature solution processing. Solar cells with efficiency greater than 20% retained 90% (97% after dark recovery) of their initial performance after 500 hours of continuous room-temperature operation at their maximum power point under 1-sun illumination (where 1 sun is defined as the standard illumination at AM1.5, or 1 kilowatt/square meter).

  11. Distribution of stable traps for thermoluminescent processes in the phosphor SrAl2O4: Eu2+, Dy3+

    International Nuclear Information System (INIS)

    Pedroza M, M.; Castaneda, B.; Arellano T, O.; Melendrez, R.; Barboza F, M.

    2007-01-01

    Full text: The phosphor of persistent luminescence (PLUM) SrAl 2 O 4 :Eu 2+ , Dy 3+ exhibits one thermoluminescence curve after exposing it to UV radiation. The curve is made up of a wide band with a maximum around 455 K. Starting from the experimental deconvolution method proposed by McKeever, it was solved the number of peaks in the TL curve and it was analyzed the position of each TL peak regarding to the cut temperature (T stop ). In this analysis five maximum TL peaks were observed (at the diagram T stop vs T max ) around the 319, 425, 457, 488 and 515 K. Also, its were also found two regions that correspond to an overlap of stable traps, the first one in the region of the 380 K at 415 K and the second of the 430 to 455 K. The existence of a distribution of stable traps can be evaluated from the curve T stop vs T max where this distribution of stable traps is presented as a monotonous lineal increase with the temperature, because the TL independent processes appear like horizontal lines exactly in the specific temperatures (319, 425, 457, 488 and 515 K) where its are liberated most of the trapped charges. Using the preheating method and initial increase for the peak in 455 K the trap depths are determined, being obtained the following values of the activation energy 0.28, 0.67, 1, 1.5 and 1.62 eV. An arrangement of stable traps plays a decisive role in the emission of the persistent luminescence. Likewise, it was determined that all the thermoluminescent processes were characterized by a re trapping of the charge, reason by which these processes followed a second order kinetics. The TL peak of low temperature 319 K is related with those electronic traps that the PLUM takes place in SrAl 2 O 4 : Eu 2+ and with the same recombination centers. The PLUM emissions and the TL are centered around 510 nm attributed to the electronic transition 4f 6 5d 1 →4f 7 corresponding to the Eu 2+ ion. In this work, it is explained the participation or contribution of the

  12. Efficient and Stable Carbon-coated Nickel Foam Cathodes for the Electro-Fenton Process

    International Nuclear Information System (INIS)

    Song, Shuqin; Wu, Mingmei; Liu, Yuhui; Zhu, Qiping; Tsiakaras, Panagiotis; Wang, Yi

    2015-01-01

    Highlights: • Carbon-coated nickel foam (C@NF) was prepared by cycle coating carbon process. • Ni leaching can be effectively controlled at C@NF4 (4 cycle coating times) cathode. • C@NF4 exhibits excellent electro-Fenton performance with desirable stability. • C@NF4 exhibits low energy consumption for DMP degradation. - Abstract: Carbon-coated nickel foam (C@NF) electrodes are prepared via a simple and effective method, hydrothermal-carbonization cycle coating process, characterized by scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and employed as the electro-Fenton (E-Fenton) cathode for degrading dimethyl phthalate (DMP) in aqueous solution. For the sake of comparison, nickel foam (NF) electrode and the conventional E-Fenton cathode (graphite gas diffusion electrode (GDE)) are also tested and compared. Experimental results indicate that nickel leaching can be effectively controlled at C@NF4 cathode (4 times cycle coating process), having great significance for promoting the application of NF in E-Fenton system. Moreover, C@NF4 cathode still presents excellent and effective performance on DMP degradation. DMP can be completely degraded within 2 h at −0.5 V and the total organic carbon (TOC) removal reaches as high as 82.1 %, which is almost 3 times as high as that at graphite GDE. Futhermore, the current efficiency for H 2 O 2 generation at C@NF4 is enhanced by 12 times compared to that at NF, and consequently the energy consumption during DMP degradation at C@NF4 is obvious lower than that at both NF cathode and graphite GDE. From the obtained results it can be deduced that C@NF4 is promising to be an attractive alternative E-Fenton cathode for removing organic pollutants in wastewater

  13. Downstream process for production of a viable and stable Bacillus cereus aquaculture biological agent

    CSIR Research Space (South Africa)

    Lalloo, R

    2010-03-01

    Full Text Available , 604 Robertson JL (1998) The use of probiotics in the diet of dogs. 605 J Nutri 128:2730S–2732S 606 Brar SK, Verma M, Tyagi RD, Valéro JR (2006) Recent advances in 607 downstream processing and formulations of Bacillus thuringien- 608 sis based..., Menasveta P (2000) Some recent issues and innovations in 630 marine shrimp pond culture. Rev Fish Sci 8:151–233 631 Gatesoupe FJ (1999) The use of probiotics in aquaculture. Aquacul- 632 ture 180:147–165 633 Guetsky R, Shtienberg Y, Elad Y, Fischer E...

  14. Computer simulation of transitional process to the final stable Brayton cycle in magnetic refrigeration

    International Nuclear Information System (INIS)

    Numasawa, T.; Hashimoto, T.

    1981-01-01

    The final working cycle in the magnetic refrigeration largely depends on the heat transfer coefficient β in the system, the parameter γ of the heat inflow from the outer system to this cycle and the period tau of the cycle. Therefore, so as to make clear this dependence, the time variation of the Brayton cycle with β, γ and tau has been investigated. In the present paper the transitional process of this cycle and the dependence of the final cooling temperature of the heat load on β, γ and tau have all been shown. (orig.)

  15. Diagnostic System of Drill Condition in Laminated Chipboard Drilling Process

    Directory of Open Access Journals (Sweden)

    Swiderski Bartosz

    2017-01-01

    Full Text Available The paper presents an on-line automatic system for recognition of the drill condition in a laminated chipboard drilling process. Two states of the drill are considered: the sharp enough (still able to drill holes acceptable for processing quality and worn out (excessive drill wear, not satisfactory from the quality point of view of the process. The automatic system requires defining the diagnostic features, which are used as the input attributes to the classifier. The features have been generated from 5 registered signals: feed force, cutting torque, noise, vibration and acoustic emission. The statistical parameters defined on the basis of the auto regression model of these signals have been used as the diagnostic features. The sequential step-wise feature selection is applied for choosing the most discriminative set of features. The final step of recognition is done by support vector machine classifier working in leave one out mode. The results of numerical experiments have confirmed good quality of the proposed diagnostic system.

  16. stableGP

    Data.gov (United States)

    National Aeronautics and Space Administration — The code in the stableGP package implements Gaussian process calculations using efficient and numerically stable algorithms. Description of the algorithms is in the...

  17. Safeguards System for the Advanced Spent Fuel Conditioning Process Facility

    International Nuclear Information System (INIS)

    Kim, Ho-dong; Lee, T.H.; Yoon, J.S.; Park, S.W; Lee, S.Y.; Li, T.K.; Menlove, H.; Miller, M.C.; Tolba, A.; Zarucki, R.; Shawky, S.; Kamya, S.

    2007-01-01

    The advanced spent fuel conditioning process (ACP) which is a part of a pyro-processing has been under development at Korean Atomic Energy Research Institute (KAERI) since 1997 to tackle the problem of an accumulation of spent fuel. The concept is to convert spent oxide fuel into a metallic form in a high temperature molten salt in order to reduce the heat energy, volume, and radioactivity of a spent fuel. Since the inactive tests of the ACP have been successfully implemented to confirm the validity of the electrolytic reduction technology, a lab-scale hot test will be undertaken in a couple of years to validate the concept. For this purpose, the KAERI has built the ACP Facility (ACPF) at the basement of the Irradiated Material Examination Facility (IMEF) of KAERI, which already has a reserved hot-cell area. Through the bilateral arrangement between US Department of Energy (DOE) and Korean Ministry of Science and Technology (MOST) for safeguards R and D, the KAERI has developed elements of safeguards system for the ACPF in cooperation with the Los Alamos National Laboratory (LANL). The reference safeguards design conditions and equipment were established for the ACPF. The ACPF safeguards system has many unique design specifications because of the particular characteristics of the pyro-process materials and the restrictions during a facility operation. For the material accounting system, a set of remote operation and maintenance concepts has been introduced for a non-destructive assay (NDA) system. The IAEA has proposed a safeguards approach to the ACPF for the different operational phases. Safeguards measures at the ACPF will be implemented during all operational phases which include a 'Cold Test', a 'Hot Test' and at the end of a 'Hot test'. Optimization of the IAEA's inspection efforts was addressed by designing an effective safeguards approach that relies on, inter alia, remote monitoring using cameras, installed NDA instrumentation, gate monitors and seals

  18. Recent results in explosive and s-process nucleosynthesis from measurements on radioactive and stable targets

    International Nuclear Information System (INIS)

    Koehler, P.E.; Kaeppeler, F.; Schatz, H.

    1993-01-01

    Measurements of (n,p) and (n,α) cross sections are crucial for a better understanding of many scenarios of nucleosynthesis. Current problems in which such reactions play a roll include the possible synthesis of heavy element during the big bang. The production of several rare isotopes in explosive nucleosynthesis, and a better understanding of the role of the s process in the synthesis of light and intermediate mass nuclei. We have recently completed measurements of several (n,p) and (n,α) cross sections of importance to nuclear astrophysics. The cross sections were measured in the range from thermal energy to approximately 1 MeV by using the white neutron source at the Manuel Lujan, Jr. Neutron Scattering Center (LANSCE) in Los Alamos. We have also made complementary measurements at the Karlsruhe Van de Graaff and at thee Oak Ridge Electron Linear Accelerator (ORELA). We discuss the impact of the results on nuclear astrophysics as well as recent improvements and future plans

  19. Thermal behaviour of used resin during conditioning process

    International Nuclear Information System (INIS)

    Arsene, C.

    2016-01-01

    In the nuclear power plants using light water and heavy water as coolant, as well as in most waste treatment installations, the ion-exchange resins are used to purify water circuits. Since the resins retain both radionuclide and chemical impurities, it represents a low- and intermediate- radioactive waste that requires special management for storage and disposal. From experimental studies it was found that the conditioning of the used resin in bitumen has several advantages. But there are some disadvantages, too, one being the significant amount of gas produced during the bituminization process because of the high temperature (1200C). Besides water vapours, the condensable gas mixture (formed by a liquid fraction and an oil fraction) contains products generated from the partial decomposition of the resin and release of degradation products of bitumen: dimethyl and trimethylamine, methanol - compounds resulting from the destruction of functional groups and hydrocarbon fraction formed by n-paraffins (C6-C32), iso-paraffins and aromatics. (authors)

  20. Research on the Combustion Characteristics of a Free-Piston Gasoline Engine Linear Generator during the Stable Generating Process

    Directory of Open Access Journals (Sweden)

    Yuxi Miao

    2016-08-01

    Full Text Available The free-piston gasoline engine linear generator (FPGLG is a new kind of power plant consisting of free-piston gasoline engines and a linear generator. Due to the elimination of the crankshaft mechanism, the piston motion process and the combustion heat release process affect each other significantly. In this paper, the combustion characteristics during the stable generating process of a FPGLG were presented using a numerical iteration method, which coupled a zero-dimensional piston dynamic model and a three-dimensional scavenging model with the combustion process simulation. The results indicated that, compared to the conventional engine (CE, the heat release process of the FPGLG lasted longer with a lower peak heat release rate. The indicated thermal efficiency of the engine was lower because less heat was released around the piston top dead centre (TDC. Very minimal difference was observed on the ignition delay duration between the FPGLG and the CE, while the post-combustion period of the FPGLG was significantly longer than that of the CE. Meanwhile, the FPGLG was found to operate more moderately due to lower peak in-cylinder gas pressure and a lower pressure rising rate. The potential advantage of the FPGLG in lower NOx emission was also proven with the simulation results presented in this paper.

  1. Dark chocolate acceptability: influence of cocoa origin and processing conditions.

    Science.gov (United States)

    Torres-Moreno, Miriam; Tarrega, Amparo; Costell, Elvira; Blanch, Consol

    2012-01-30

    Chocolate properties can vary depending on cocoa origin, composition and manufacturing procedure, which affect consumer acceptability. The aim of this work was to study the effect of two cocoa origins (Ghana and Ecuador) and two processing conditions (roasting time and conching time) on dark chocolate acceptability. Overall acceptability and acceptability for different attributes (colour, flavour, odour and texture) were evaluated by 95 consumers. Differences in acceptability among dark chocolates were mainly related to differences in flavour acceptability. The use of a long roasting time lowered chocolate acceptability in Ghanaian samples while it had no effect on acceptability of Ecuadorian chocolates. This response was observed for most consumers (two subgroups with different frequency consumption of dark chocolate). However, for a third group of consumers identified as distinguishers, the most acceptable dark chocolate samples were those produced with specific combinations of roasting time and conching time for each of the cocoa geographical origin considered. To produce dark chocolates from a single origin it is important to know the target market preferences and to select the appropriate roasting and conching conditions. Copyright © 2011 Society of Chemical Industry.

  2. Influence of processing conditions in PEA/organophilic clay nanocomposites

    International Nuclear Information System (INIS)

    Araujo, E.M.; Kojuch, L.R.; Barbosa, R.; Nobrega, K.C.; Melo, T.J.A. de

    2008-01-01

    Polymer/clay nanocomposites have attracted great interest from the industry as well as from the researches due to the need to obtain materials with desired properties. Nanocomposites with silicates layer represent an alternative for the conventional composites because they use a small amount of nanofiller. In this work, polyethylene/polyethylene grafted anhydride maleic (PE-g-MA)/montmorillonite clay (MMT) nanocomposites were prepared by melt intercalation in a Torque Rheometer. It was used an untreated clay (MMT) and a treated clay with the quaternary ammonium salt (OMMT). The influence of the processing conditions was evaluated, that is: 60 and 120rpm, 7 and 14 min, 190 and 220°C. The obtained systems were characterized by X-ray diffraction (XRD) and rheological behavior. The results from XRD and rheological behavior indicated that the system composed of polyethylene/PE-g-MA/OMMT presented intercalated nanocomposite structure, with larger basal distance and high viscosity, in the conditions of 120rpm and 7min, independent of temperature. (author)

  3. Fate of stable strontium in the sewage treatment process as an analog for radiostrontium released by nuclear accidents

    International Nuclear Information System (INIS)

    Kamei-Ishikawa, Nao; Ito, Ayumi; Umita, Teruyuki

    2013-01-01

    Highlights: • 76% of the Sr entering the plant was discharged to receiving water. • 21% of the Sr flowing through the plant was transferred to the sewage sludge. •Almost all of the Sr in the sewage sludge was concentrated in incinerated sewage sludge ash. • Activated sludge had a lower sorption capacity for Sr than metals such as Cd. -- Abstract: Radionuclides were widely released into the environment due to the nuclear accident at the Fukushima Daiichi Nuclear Power Plant. Some of these radionuclides have flowed into municipal sewage treatment plants through sewer systems. We have observed the fate of stable Sr in the sewage treatment process as a means to predict the fate of radiostrontium. Concentrations of stable Sr were determined in sewage influent, effluent, dewatered sludge, and incinerated sewage sludge ash collected from a sewage treatment plant once a month from July to December 2011. In the mass balance of Sr in the sewage treatment plant, 76% of the Sr entering the plant was discharged to the receiving water on average. Additionally, 14% of the Sr flowing through the plant was transferred to the sewage sludge and then concentrated in the sludge ash without being released to the atmosphere. We also investigated Sr sorption by activated sludge in a batch experiment. Measurements at 3 and 6 h after the contact showed Sr was sorbed in the activated sludge; however, the measurements indicated Sr desorption from activated sludge occurred 48 h after the contact

  4. Effect of Processing Delay and Storage Conditions on Urine Albumin-to-Creatinine Ratio.

    Science.gov (United States)

    Herrington, William; Illingworth, Nicola; Staplin, Natalie; Kumar, Aishwarya; Storey, Ben; Hrusecka, Renata; Judge, Parminder; Mahmood, Maria; Parish, Sarah; Landray, Martin; Haynes, Richard; Baigent, Colin; Hill, Michael; Clark, Sarah

    2016-10-07

    Because there is substantial biologic intraindividual variation in albumin excretion, randomized trials of albuminuria-reducing therapies may need multiple urine samples to estimate daily urinary albumin excretion. Mailing spot urine samples could offer a convenient and cost-effective method to collect multiple samples, but urine albumin-to-creatinine ratio stability in samples stored at ambient temperatures for several days is unknown. Patients with kidney disease provided fresh urine samples in two tubes (with and without boric acid preservative). Reference aliquots from each participant were analyzed immediately, whereas remaining aliquots were subject to different handling/storage conditions before analysis, including delayed processing for up to 7 days at three different storage temperatures (4°C, 18°C, and 30°C), multiple freeze-thaw cycles, and long-term frozen storage at -80°C, -40°C, and -20°C. We calculated the mean percentage change in urine albumin-to-creatinine ratio for each condition, and we considered samples stable if the 95% confidence interval was within a ±5% threshold. Ninety-three patients provided samples with detectable albuminuria in the reference aliquot. Median (interquartile range) urine albumin-to-creatinine ratio was 87 (20-499) mg/g. The inclusion of preservative had minimal effect on fresh urine albumin-to-creatinine ratio measurements but reduced the changes in albumin and creatinine in samples subject to processing delay and storage conditions. The urine albumin-to-creatinine ratio was stable for 7 days in samples containing preservative at 4°C and 18°C and 2 days when stored at 30°C. It was also stable in samples with preservative after three freeze-thaw cycles and in frozen storage for 6 months at -80°C or -40°C but not at -20°C. Mailed urine samples collected with preservative and received within 7 days if ambient temperature is ≤18°C, or within 2 days if the temperature is higher but does not exceed 30°C, are

  5. Effect of Processing Delay and Storage Conditions on Urine Albumin-to-Creatinine Ratio

    Science.gov (United States)

    Illingworth, Nicola; Staplin, Natalie; Kumar, Aishwarya; Storey, Ben; Hrusecka, Renata; Judge, Parminder; Mahmood, Maria; Parish, Sarah; Landray, Martin; Haynes, Richard; Baigent, Colin; Hill, Michael; Clark, Sarah

    2016-01-01

    Background and objectives Because there is substantial biologic intraindividual variation in albumin excretion, randomized trials of albuminuria-reducing therapies may need multiple urine samples to estimate daily urinary albumin excretion. Mailing spot urine samples could offer a convenient and cost-effective method to collect multiple samples, but urine albumin-to-creatinine ratio stability in samples stored at ambient temperatures for several days is unknown. Design, setting, participants, & measurements Patients with kidney disease provided fresh urine samples in two tubes (with and without boric acid preservative). Reference aliquots from each participant were analyzed immediately, whereas remaining aliquots were subject to different handling/storage conditions before analysis, including delayed processing for up to 7 days at three different storage temperatures (4°C, 18°C, and 30°C), multiple freeze-thaw cycles, and long–term frozen storage at −80°C, −40°C, and −20°C. We calculated the mean percentage change in urine albumin-to-creatinine ratio for each condition, and we considered samples stable if the 95% confidence interval was within a ±5% threshold. Results Ninety-three patients provided samples with detectable albuminuria in the reference aliquot. Median (interquartile range) urine albumin-to-creatinine ratio was 87 (20–499) mg/g. The inclusion of preservative had minimal effect on fresh urine albumin-to-creatinine ratio measurements but reduced the changes in albumin and creatinine in samples subject to processing delay and storage conditions. The urine albumin-to-creatinine ratio was stable for 7 days in samples containing preservative at 4°C and 18°C and 2 days when stored at 30°C. It was also stable in samples with preservative after three freeze-thaw cycles and in frozen storage for 6 months at −80°C or −40°C but not at −20°C. Conclusions Mailed urine samples collected with preservative and received within 7 days if

  6. Real time process algebra with time-dependent conditions

    NARCIS (Netherlands)

    Baeten, J.C.M.; Middelburg, C.A.

    We extend the main real time version of ACP presented in [6] with conditionals in which the condition depends on time. This extension facilitates flexible dependence of proccess behaviour on initialization time. We show that the conditions concerned generalize the conditions introduced earlier

  7. Stable-isotope analysis of a combined nitrification-denitrification sustained by thermophilic methanotrophs under low-oxygen conditions

    NARCIS (Netherlands)

    Pel, R; Oldenhuis, R; Brand, W; Vos, A; Gottschal, JC; Zwart, KB

    To simulate growth conditions experienced by microbiota at O-2-limited interfaces of organic matter in compost, an experimental system capable of maintaining dual limitations of oxygen and carbon for extended periods, i.e., a pO(2)-auxostat, has been used. N-15 tracer studies on thermophilic (53

  8. Stable-isotope analysis of a combined nitrification- denitrification sustained by thermophilic methanotrophs under low-oxygen conditions

    NARCIS (Netherlands)

    Pel, R.; Oldenhuis, R.; Brand, W.; Vos, A.; Gottschal, J.C.; Zwart, K.B.

    1997-01-01

    To simulate growth conditions experienced by microbiota at O-2- limited interfaces of organic matter in compost, an experimental system capable of maintaining dual limitations of oxygen and carbon for extended periods, i.e., a pO(2)-auxostat, has been used. N-15 tracer studies on thermophilic (53

  9. Near-field krypton-85 measurements in stable meteorological conditions around the AREVA NC La Hague reprocessing plant: estimation of atmospheric transfer coefficients.

    Science.gov (United States)

    Connan, O; Solier, L; Hébert, D; Maro, D; Lamotte, M; Voiseux, C; Laguionie, P; Cazimajou, O; Le Cavelier, S; Godinot, C; Morillon, M; Thomas, L; Percot, S

    2014-11-01

    The aim of this work was to study the near-field dispersion of (85)Kr around the nuclear fuel reprocessing plant at La Hague (AREVA NC La Hague - France) under stable meteorological conditions. Twenty-two (85)Kr night-time experimental campaigns were carried out at distances of up to 4 km from the release source. Although the operational Gaussian models predict for these meteorological conditions a distance to plume touchdown of several kilometers, we almost systematically observed a marked ground signal at distances of 0.5-4 km. The calculated atmospheric transfer coefficients (ATC) show values (1) higher than those observed under neutral conditions, (2) much higher than those proposed by the operational models, and (3) higher than those used in the impact assessments. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. Development of stable walking robot for accident condition monitoring on uneven floors in a nuclear power plant

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Seog; Jang, You Hyun [Central Research Institute of Korea Hydro and Nuclear Power Company, Daejeon (Korea, Republic of)

    2017-04-15

    Even though the potential for an accident in nuclear power plants is very low, multiple emergency plans are necessary because the impact of such an accident to the public is enormous. One of these emergency plans involves a robotic system for investigating accidents under conditions of high radiation and contaminated air. To develop a robot suitable for operation in a nuclear power plant, we focused on eliminating the three major obstacles that challenge robots in such conditions: the disconnection of radio communication, falling on uneven floors, and loss of localization. To solve the radio problem, a Wi-Fi extender was used in radio shadow areas. To reinforce the walking, we developed two- and four-leg convertible walking, a floor adaptive foot, a roly-poly defensive falling design, and automatic standing recovery after falling methods were developed. To allow the robot to determine its location in the containment building, a bar code landmark reading method was chosen. When a severe accident occurs, this robot will be useful for accident condition monitoring. We also anticipate the robot can serve as a workman aid in a high radiation area during normal operations.

  11. Identification of milk origin and process-induced changes in milk by stable isotope ratio mass spectrometry.

    Science.gov (United States)

    Scampicchio, Matteo; Mimmo, Tanja; Capici, Calogero; Huck, Christian; Innocente, Nadia; Drusch, Stephan; Cesco, Stefano

    2012-11-14

    Stable isotope values were used to develop a new analytical approach enabling the simultaneous identification of milk samples either processed with different heating regimens or from different geographical origins. The samples consisted of raw, pasteurized (HTST), and ultrapasteurized (UHT) milk from different Italian origins. The approach consisted of the analysis of the isotope ratio of δ¹³C and δ¹⁵N for the milk samples and their fractions (fat, casein, and whey). The main finding of this work is that as the heat processing affects the composition of the milk fractions, changes in δ¹³C and δ¹⁵N were also observed. These changes were used as markers to develop pattern recognition maps based on principal component analysis and supervised classification models, such as linear discriminant analysis (LDA), multivariate regression (MLR), principal component regression (PCR), and partial least-squares (PLS). The results give proof of the concept that isotope ratio mass spectroscopy can discriminate simultaneously between milk samples according to their geographical origin and type of processing.

  12. STATIC BALANCE MEASUREMENTS IN STABLE AND UNSTABLE CONDITIONS DO NOT DISCRIMINATE GROUPS OF YOUNG ADULTS ASSESSED BY THE FUNCTIONAL MOVEMENT SCREEN™ (FMS™).

    Science.gov (United States)

    Trindade, Matheus A; de Toledo, Aline Martins; Cardoso, Jefferson Rosa; Souza, Igor Eduardo; Dos Santos Mendes, Felipe Augusto; Santana, Luisiane A; Carregaro, Rodrigo Luiz

    2017-11-01

    The Functional Movement Screen™ (FMS™) has been the focus of recent research related to movement profiling and injury prediction. However, there is a paucity of studies examining the associations between physical performance tasks such as balance and the FMS™ screening system. The purpose of this study was to compare measures of static balance in stable and unstable conditions between different groups divided by FMS™ scores. A secondary purpose was to discern if balance indices discriminate the groups divided by FMS™ scores. Cross-sectional study. Fifty-seven physically active subjects (25 men and 32 women; mean age of 22.9 ± 3.1 yrs) participated. The outcome was unilateral stance balance indices, composed by: Anteroposterior Index; Medial-lateral Index, and Overall Balance Index in stable and unstable conditions, as provided by the Biodex balance platform. Subjects were dichotomized into two groups, according to a FMS™ cut-off score of 14: FMS1 (score > 14) and FMS2 (score ≤ 14). The independent Students t-test was used to verify differences in balance indices between FMS1 and FMS2 groups. A discriminant analysis was applied in order to identify which of the balance indices would adequately discriminate the FMS™ groups. Comparisons between FMS1 and FMS2 groups in the stable and unstable conditions demonstrated a higher unstable Anteroposterior index for FMS2 (p=0.017). No significant differences were found for other comparisons (p>0.05). The indices did not discriminate the FMS™ groups ( p  > 0.05). The balance indices adopted in this study were not useful as a parameter for identification and discrimination of healthy subjects assessed by the FMS™. 2c.

  13. Creative Industries: Development Processes Under Contemporary Conditions of Globalization

    Directory of Open Access Journals (Sweden)

    Valerija Kontrimienė

    2017-06-01

    Full Text Available The article deals with the processes of developing creative industries under conditions of a growth in the worldwide economy and globalization, discloses the role of the sector of creative industries and shows its place in the system of the modern global economy. The paper presents a comparative analysis of theories and theoretical approaches intended for the sector of creative industries and its development as well as defines regularities and specificities characteristic of the development of creative industries. Particular attention is shifted on the growth and development of creative industries considering the current challenges of globalization and on the most important specificities of the developing sector in the context of the challenges of economic globalization. The paper examines the trends reflecting the place of the sector of creative industries in the economy of the modern world, including the tendencies indicating changes in the export of the products created in this sector. The article considers the issues of developing creative industries and reveals priorities of future research.

  14. The influence of hydraulic conditions on coagulation process effectiveness

    Directory of Open Access Journals (Sweden)

    Sambor Aleksandra

    2017-01-01

    Full Text Available This paper presents the impact that small changes in the hydraulic installation between the flocculation chamber and the sedimentation tanks have on coagulation process effectiveness. This study has shown significant improvements in the parameters of the treated water. The research was conducted in two treatment systems: reference and test, in order to compare the changes that were introduced in the time period between January and May 2016. The hydraulic conditions between the flocculation chamber and the sedimentation tank were changed in the test system, leaving the reference system unchanged for comparative purposes. The height-wise positioning of the sedimentation tank relative to the flocculation chamber resulted in a formation of a cascade at the flocculation chamber drain at a height of 0.60m. Air was therefore introduced into the water, forming an air-water mixture, which disturbed the flow between the devices. It was found that floc transported by the pipeline was broken down, which hampered sedimentation in the sedimentation tank. This was confirmed by the analysis of chosen parameters from treated water. After changes in the hydraulic system, changes in water turbidity were noticed, indicating an increase in post-coagulation suspension separation effectiveness. Consequently, an increase in organic carbon removal was found relative to the reference system. This change influenced changes in UV254 absorbance to a much lesser extent.

  15. The influence of hydraulic conditions on coagulation process effectiveness

    Science.gov (United States)

    Sambor, Aleksandra; Ferenc, Zbigniew

    2017-11-01

    This paper presents the impact that small changes in the hydraulic installation between the flocculation chamber and the sedimentation tanks have on coagulation process effectiveness. This study has shown significant improvements in the parameters of the treated water. The research was conducted in two treatment systems: reference and test, in order to compare the changes that were introduced in the time period between January and May 2016. The hydraulic conditions between the flocculation chamber and the sedimentation tank were changed in the test system, leaving the reference system unchanged for comparative purposes. The height-wise positioning of the sedimentation tank relative to the flocculation chamber resulted in a formation of a cascade at the flocculation chamber drain at a height of 0.60m. Air was therefore introduced into the water, forming an air-water mixture, which disturbed the flow between the devices. It was found that floc transported by the pipeline was broken down, which hampered sedimentation in the sedimentation tank. This was confirmed by the analysis of chosen parameters from treated water. After changes in the hydraulic system, changes in water turbidity were noticed, indicating an increase in post-coagulation suspension separation effectiveness. Consequently, an increase in organic carbon removal was found relative to the reference system. This change influenced changes in UV254 absorbance to a much lesser extent.

  16. Effect of substrate availability on nitrous oxide production by deammonification processes under anoxic conditions.

    Science.gov (United States)

    Schneider, Yvonne; Beier, Maike; Rosenwinkel, Karl-Heinz

    2012-05-01

    Due to its high global warming potential, nitrous oxide (N(2)O) emissions from wastewater treatment processes have recently received a high degree of attention. Nevertheless, there is still a lack of information regarding the microbiological processes leading to N(2)O production. In this study, two lab-scale sequencing batch reactors were operated with deammonification biomass to investigate the role of denitrification and the influence of substrate availability regarding N(2)O formation during the anoxic phase of deammonification. Three different operational phases were established: within the first phase conversion by anammox was favoured and after a transition phase, denitrification activity was promoted. Low nitrous oxide production was observed during stable operation aiming for anammox conversion. Pulsed inflow of the wastewater containing ammonium (NH(4)(+)) and nitrite (NO(2)(-)) led to increased N(2)O production rates. Within the period of denitrification as dominating nitrogen conversion process, the nitrous oxide concentration level was higher during continuous inflow conditions, but the reaction to pulsed inflow was less pronounced. The results indicated that denitrification was responsible for N(2)O formation from the deammonification biomass. Operational settings to achieve suppression of denitrification processes to a large extend were deducted from the results of the experiments. © 2012 The Authors. Microbial Biotechnology © 2012 Society for Applied Microbiology and Blackwell Publishing Ltd.

  17. A Conditionally Stable Scheme for a Transient Flow of a Non-Newtonian Fluid Saturating a Porous Medium

    KAUST Repository

    El-Amin, Mohamed; Salama, Amgad; Sun, Shuyu

    2012-01-01

    The problem of thermal dispersion effects on unsteady free convection from an isothermal horizontal circular cylinder to a non-Newtonian fluid saturating a porous medium is examined numerically. The Darcy-Brinkman-Forchheimer model is employed to describe the flow field. The thermal diffusivity coefficient has been assumed to be the sum of the molecular diffusivity and the dynamic diffusivity due to mechanical dispersion. The simultaneous development of the momentum and thermal boundary layers are obtained by using finite difference method. The stability conditions are determined for each difference equation. Using an explicit finite difference scheme, solutions at each time-step have been found and then stepped forward in time until reaching steady state solution. Velocity and temperature profiles are shown graphically. It is found that as time approaches infinity, the values of friction factor and heat transfer coefficient approach the steady state values.

  18. A Conditionally Stable Scheme for a Transient Flow of a Non-Newtonian Fluid Saturating a Porous Medium

    KAUST Repository

    El-Amin, Mohamed

    2012-06-02

    The problem of thermal dispersion effects on unsteady free convection from an isothermal horizontal circular cylinder to a non-Newtonian fluid saturating a porous medium is examined numerically. The Darcy-Brinkman-Forchheimer model is employed to describe the flow field. The thermal diffusivity coefficient has been assumed to be the sum of the molecular diffusivity and the dynamic diffusivity due to mechanical dispersion. The simultaneous development of the momentum and thermal boundary layers are obtained by using finite difference method. The stability conditions are determined for each difference equation. Using an explicit finite difference scheme, solutions at each time-step have been found and then stepped forward in time until reaching steady state solution. Velocity and temperature profiles are shown graphically. It is found that as time approaches infinity, the values of friction factor and heat transfer coefficient approach the steady state values.

  19. Using stable isotopes to understand hydrochemical processes in and around a Prairie Pothole wetland in the Northern Great Plains, USA

    International Nuclear Information System (INIS)

    Mills, Christopher T.; Goldhaber, Martin B.; Stricker, Craig A.; Holloway, JoAnn M.; Morrison, Jean M.; Ellefsen, Karl J.; Rosenberry, Donald O.; Thurston, Roland S.

    2011-01-01

    Highlights: → A stable isotope study of the hydrochemistry of a Prairie Pothole wetland system. → δ 18 O H2O and δ 2 H H2O values show salt concentration by transpiration at wetland edge. → A range of δ 34 S SO4 values indicate SO 4 source and reduction processes. → Isotopic mixing lines show interaction of surface and groundwater at wetland edge. - Abstract: Millions of internally drained wetland systems in the Prairie Potholes region of the northern Great Plains (USA and Canada) provide indispensable habitat for waterfowl and a host of other ecosystem services. The hydrochemistry of these systems is complex and a crucial control on wetland function, flora and fauna. Wetland waters can have high concentrations of SO 4 2- due to the oxidation of large amounts of pyrite in glacial till that is in part derived from the Pierre shale. Water chemistry including δ 18 O H2O , δ 2 H H2O , and δ 34 S SO4 values, was determined for groundwater, soil pore water, and wetland surface water in and around a discharge wetland in North Dakota. The isotopic data for the first time trace the interaction of processes that affect wetland chemistry, including open water evaporation, plant transpiration, and microbial SO 4 reduction.

  20. Radioactive spent resins conditioning by the hot super-compaction process

    International Nuclear Information System (INIS)

    Roth, Andreas; Centner, Baudouin; Lemmens, Alain

    2007-01-01

    Spent ion exchanger media are considered to be problematic waste that, in many cases, requires special approaches and precautions during its immobilization to meet the acceptance criteria for disposal. The waste acceptance criteria define, among others, the quality of waste forms for disposal, and therefore will sometimes define appropriate treatment options. The selection of treatment options for spent ion exchange materials must consider their physical and chemical characteristics. Basically, the main methods for the treatment of spent organic ion exchange materials, following to pretreatment methods are: - Direct immobilization, producing a stable end product by using Cement, Bitumen, Polymer or High Integrity Containers, - The destruction of the organic compounds by using Thermochemical processes or Oxidation to produce an inorganic intermediate product that may or may not be further conditioned for storage and/or disposal, - The complete removal of the resin inner structural water by a thermal process. After a thorough technical economical analysis, Tractebel Engineering selected the Resin Hot Compaction Process to be installed at Tihange Nuclear Power Plant. The Resin Hot Compaction Process is used to make dense homogenous organic blocks from a wide range of particulate waste. In this process spent resins are first dewatered and dried to remove the inner structural water content. The drying takes place in a drying vessel that holds the contents of two 200 L drums (Figure). In the oil heated drying and mixing unit, the resins are heated to the necessary process temperature for the hot pressing step and then placed into special metal drums, which are automatically lidded and immediately transferred to a high force compactor. After high force compaction the pellets are transferred to a measuring unit, where the dose rate, height and weight are automatically measured and recorded. A volume reduction factor of approximately up to four (depending on the type of

  1. Sex differences in learning processes of classical and operant conditioning.

    Science.gov (United States)

    Dalla, Christina; Shors, Tracey J

    2009-05-25

    Males and females learn and remember differently at different times in their lives. These differences occur in most species, from invertebrates to humans. We review here sex differences as they occur in laboratory rodent species. We focus on classical and operant conditioning paradigms, including classical eyeblink conditioning, fear-conditioning, active avoidance and conditioned taste aversion. Sex differences have been reported during acquisition, retention and extinction in most of these paradigms. In general, females perform better than males in the classical eyeblink conditioning, in fear-potentiated startle and in most operant conditioning tasks, such as the active avoidance test. However, in the classical fear-conditioning paradigm, in certain lever-pressing paradigms and in the conditioned taste aversion, males outperform females or are more resistant to extinction. Most sex differences in conditioning are dependent on organizational effects of gonadal hormones during early development of the brain, in addition to modulation by activational effects during puberty and adulthood. Critically, sex differences in performance account for some of the reported effects on learning and these are discussed throughout the review. Because so many mental disorders are more prevalent in one sex than the other, it is important to consider sex differences in learning when applying animal models of learning for these disorders. Finally, we discuss how sex differences in learning continue to alter the brain throughout the lifespan. Thus, sex differences in learning are not only mediated by sex differences in the brain, but also contribute to them.

  2. Formation of stable Si–O–C submonolayers on hydrogen-terminated silicon(111 under low-temperature conditions

    Directory of Open Access Journals (Sweden)

    Yit Lung Khung

    2015-01-01

    Full Text Available In this letter, we report results of a hydrosilylation carried out on bifunctional molecules by using two different approaches, namely through thermal treatment and photochemical treatment through UV irradiation. Previously, our group also demonstrated that in a mixed alkyne/alcohol solution, surface coupling is biased towards the formation of Si–O–C linkages instead of Si–C linkages, thus indirectly supporting the kinetic model of hydrogen abstraction from the Si–H surface (Khung, Y. L. et al. Chem. – Eur. J. 2014, 20, 15151–15158. To further examine the probability of this kinetic model we compare the results from reactions with bifunctional alkynes carried out under thermal treatment (<130 °C and under UV irradiation, respectively. X-ray photoelectron spectroscopy and contact angle measurements showed that under thermal conditions, the Si–H surface predominately reacts to form Si–O–C bonds from ethynylbenzyl alcohol solution while the UV photochemical route ensures that the alcohol-based alkyne may also form Si–C bonds, thus producing a monolayer of mixed linkages. The results suggested the importance of surface radicals as well as the type of terminal group as being essential towards directing the nature of surface linkage.

  3. A simple condition monitoring model for a direct monitoring process

    NARCIS (Netherlands)

    Christer, A.H.; Wang, Wenbin

    1995-01-01

    This paper addresses the problem of condition monitoring of a component which has available a measure of condition called wear. Wear accumulates over time and monitoring inspections are performed at chosen times to monitor and measure the cumulative wear. If past measurements of wear are available

  4. Starch hydrolysis under low water conditions: a conceptual process design

    NARCIS (Netherlands)

    Veen, van der M.E.; Veelaert, S.; Goot, van der A.J.; Boom, R.M.

    2006-01-01

    A process concept is presented for the hydrolysis of starch to glucose in highly concentrated systems. Depending on the moisture content, the process consists of two or three stages. The two-stage process comprises combined thermal and enzymatic liquefaction, followed by enzymatic saccharification.

  5. Aerobic storage under dynamic conditions in activated sludge processes

    DEFF Research Database (Denmark)

    Majone, M.; Dircks, K.

    1999-01-01

    In activated sludge processes, several plant configurations (like plug-flow configuration of the aeration tanks, systems with selectors, contact-stabilization processes or SBR processes) impose a concentration gradient of the carbon sources to the biomass. As a consequence, the biomass grows unde...

  6. Change of body composition in process of power conditional training

    Directory of Open Access Journals (Sweden)

    D.M. Anikieiev

    2015-12-01

    Full Text Available Purpose: to work out recommendations on choosing of exercises for power conditional trainees, considering decrease of fat mass percentage as the purpose. Methods: analysis of changes of body composition of trainees, practicing different kinds of conditional power training. Results: the data about influence of different physical loads on thickness of subcutaneous fat in different parts of body have been generalized. Recommendations on choosing of exercises for power conditional trainees for body composition improving have been presented. It was found that fat loss occurs quicker in upper part of body (subcutaneous and visceral. This is observed with increasing of motor functioning and reducing calories of eating. When training any separate muscular group changes of subcutaneous fat take place not compulsory in body parts, in which the trained group is located. Conclusions: it is purposeful to mainly use basic (multi-joint exercises in power conditional training.

  7. Stable Boundary Layer Issues

    OpenAIRE

    Steeneveld, G.J.

    2012-01-01

    Understanding and prediction of the stable atmospheric boundary layer is a challenging task. Many physical processes are relevant in the stable boundary layer, i.e. turbulence, radiation, land surface coupling, orographic turbulent and gravity wave drag, and land surface heterogeneity. The development of robust stable boundary layer parameterizations for use in NWP and climate models is hampered by the multiplicity of processes and their unknown interactions. As a result, these models suffer ...

  8. Application of 13C and 15N stable isotope probing to characterize RDX degrading microbial communities under different electron-accepting conditions

    International Nuclear Information System (INIS)

    Cho, Kun-Ching; Lee, Do Gyun; Fuller, Mark E.; Hatzinger, Paul B.; Condee, Charles W.; Chu, Kung-Hui

    2015-01-01

    Highlights: • SIP characterized RDX-degrading communities under different e-accepting conditions. • Dominant RDX degradation pathways differed under different e-accepting conditions. • More complete detoxification of RDX occurred under methanogenic and sulfate-reducing conditions than under manganese(IV) and iron(III)-reducing conditions. - Abstract: This study identified microorganisms capable of using the explosive hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX) or its metabolites as carbon and/or nitrogen sources under different electron-accepting conditions using 13 C and 15 N stable isotope probing (SIP). Mesocosms were constructed using groundwater and aquifer solids from an RDX-contaminated aquifer. The mesocosms received succinate as a carbon source and one of four electron acceptors (nitrate, manganese(IV), iron(III), or sulfate) or no additional electron acceptor (to stimulate methanogenesis). When RDX degradation was observed, subsamples from each mesocosm were removed and amended with 13 C 3 - or ring- 15 N 3 -, nitro- 15 N 3 -, or fully-labeled 15 N 6 -RDX, followed by additional incubation and isolation of labeled nucleic acids. A total of fifteen 16S rRNA sequences, clustering in α- and γ-Proteobacteria, Clostridia, and Actinobacteria, were detected in the 13 C-DNA fractions. A total of twenty seven sequences were derived from different 15 N-DNA fractions, with the sequences clustered in α- and γ-Proteobacteria, and Clostridia. Interestingly, sequences identified as Desulfosporosinus sp. (in the Clostridia) were not only observed to incorporate the labeled 13 C or 15 N from labeled RDX, but also were detected under each of the different electron-accepting conditions. The data suggest that 13 C- and 15 N-SIP can be used to characterize microbial communities involved in RDX biodegradation, and that the dominant pathway of RDX biodegradation may differ under different electron-accepting conditions

  9. High-level waste processing and conditioning: vitrification

    International Nuclear Information System (INIS)

    Bonniaud, R.

    1981-02-01

    The vitrification process used to treat fission product solutions at the Marcoule Vitrification Plant is described. The type of waste processed is characterized by its very high activity and the long lifetimes of some of the emitters that it contains. The performance obtained with this process is given together with the future developments envisaged. The storage of glasses is described as well as their behavior with time [fr

  10. Fluidized-bed reactors processes and operating conditions

    CERN Document Server

    Yates, John G

    2016-01-01

    The fluidized-bed reactor is the centerpiece of industrial fluidization processes. This book focuses on the design and operation of fluidized beds in many different industrial processes, emphasizing the rationale for choosing fluidized beds for each particular process. The book starts with a brief history of fluidization from its inception in the 1940’s. The authors present both the fluid dynamics of gas-solid fluidized beds and the extensive experimental studies of operating systems and they set them in the context of operating processes that use fluid-bed reactors. Chemical engineering students and postdocs as well as practicing engineers will find great interest in this book.

  11. Study on Oxidation or Reduction Behavior of Cs-Te-O System with Gas Conditions of Voloxidation Process

    International Nuclear Information System (INIS)

    Park, Byung Heung

    2013-01-01

    Pyroprocessing has been developed for the purpose of resolving the current spent nuclear fuel management issue and enhancing the recycle of valuable resources. Pyroprocessing has been developed with the dry technologies which are performed under high temperature conditions excluding any aqueous processes. Pyro-processes which are based on the electrochemical principles require pretreatment processes and a voloxidation process is considered as a pretreatment step for an electrolytic reduction process. Various kinds of gas conditions are applicable to the voloxidation process and the understanding of Cs behavior during the process is of importance for the analyses of waste characteristics and heat load on the overall pyroprocessing. In this study, the changes of chemical compounds with the gas conditions were calculated by analyzing gas-solid reaction behavior based on the chemical equilibria on a Cs-Te-O system. Cs 2 TeO 3 and Cs 2 TeO 4 were selected after a Tpp diagram analysis and it was confirmed that they are relatively stable under oxidizing atmospheres while it was shown that Cs and Te would be removed by volatilization under reducing atmosphere at a high temperature. This work provided basic data for predicting Cs behavior during the voloxidation process at which compounds are chemically distributed as the first stage in the pyroprocessing and it is expected that the results would be used for setting up material balances and related purposes

  12. Stable isotope (δ"1"3C and δ"1"5N) based interpretation of organic matter source and paleoenvironmental conditions in Al-Azraq basin, Jordan

    International Nuclear Information System (INIS)

    Ahmad, Khaldoun; Davies, Caroline

    2017-01-01

    This study examines the stable isotopes of carbon and nitrogen from cored lacustrine sediments of the Al-Azraq, an arid lake basin on the Jordan Plateau. Lacustrine sediments contain valuable records of paleoenvironmental conditions, recording local and regional responses to environmental change. Previous paleo-reconstructions on the Jordan Plateau are based on archaeology, pollen, mineralogy, and stratigraphy. The application of organic geochemistry analyses to these lake sediments identifies multiple sources of organic matter, biological production, and contributes to understanding the paleoenvironments of the Al-Azraq basin during the mid-Pleistocene period. Organic carbon concentration (Corg) provides an overview of the organic matter distribution. Carbon isotopic composition (δ13Corg) and nitrogen isotopic composition (δ15N) are indicators of organic matter sources and paleoproductivity. Magnetic susceptibility (MGSUS) measured the concentration of ferromagnetic minerals and indicated aeolian inputs. Organic geochemistry differentiated five paleoenvironmental zones with specific sources of organic matter, both aquatic and terrestrial. It identified a long period of climate wetter than the present, punctuated by a short intense period of aridity. Diagenesis plays an important role in the decomposition of organic matter and studies indicate this degradation can alter the isotopic signals of organic matter. Analyses of the isotopic signals and statistical analyses demonstrate diagenesis is not a factor in the Al-Azraq sediments in all but Zone 4 of the paleoenvironmental zones. This Zone is defined by less negative carbon isotopic composition and the presence of thick primary gypsum layers, in addition to the influx of high peaks of aeolian sediment as reflected in the magnetic susceptibility data. Stable isotope geochemistry provides detailed information on the paleoenvironments of lake sediments, and is applicable to typically challenging arid basin sediments

  13. Modulations of the processing of line discontinuities under selective attention conditions?

    Science.gov (United States)

    Giersch, Anne; Fahle, Manfred

    2002-01-01

    We examined whether the processing of discontinuities involved in figure-ground segmentation, like line ends, can be modulated under selective attention conditions. Subjects decided whether a gap in collinear or parallel lines was located to the right or left. Two stimuli were displayed in immediate succession. When the gaps were on the same side, reaction times (RTs) for the second stimulus increased when collinear lines followed parallel lines, or the reverse, but only when the two stimuli shared the same orientation and location. The effect did not depend on the global form of the stimuli or on the relative orientation of the gaps. A frame drawn around collinear elements affected the results, suggesting a crucial role of the "amodal" orthogonal lines produced when line ends are aligned. Including several gaps in the first stimulus also eliminated RT variations. By contrast, RT variations remained stable across several experimental blocks and were significant for interstimulus intervals from 50 to 600 msec between the two stimuli. These results are interpreted in terms of a modulation of the processing of line ends or the production of amodal lines, arising when attention is selectively drawn to a gap.

  14. Stable carbon isotopic composition of tree rings from a pine tree from Augustów Wilderness, Poland, as a temperature and local environment conditions indicator.

    Science.gov (United States)

    Pawelczyk, Slawomira; Pazdur, Anna; Halas, Stanislaw

    2004-06-01

    Tree rings can be used as archives of climatic and environmental data with annual resolution. Tree rings widths, maximum late wood density and other parameters as stable composition in tree rings can be used for the reconstruction of past climatic and environmental changes. Stable carbon isotope ratios in tree rings may provide valuable information on past climatic conditions. 13C/12C ratios of plant organic matter can reflect corresponding 13C/12C ratio of atmospheric CO2 during formation of the rings. Investigations of isotopic carbon composition in tree rings from in the ecologically clean the Augustów Wilderness region in the north-eastern part of Poland (22 degrees 58'E, 53 degrees 51'N) (nowadays a sanctuary) were undertaken. Series of delta13C in alpha-cellulose and in wholewood were acquired. Those measurements constituted a part of more complex investigations of carbon isotope composition in tree rings including the measurements of radiocarbon concentration and tree ring widths. This article presents preliminary results. It is argued that contrary to the tree ring widths and delta13C in wholewood that do not reveal significant correlation with temperature, the variation of delta13C in the latewood alpha-cellulose is correlated with combined July and August temperatures. Copyright 2004 Taylor and Francis Ltd.

  15. Condition Monitoring of a Process Filter Applying Wireless Vibration Analysis

    Directory of Open Access Journals (Sweden)

    Pekka KOSKELA

    2011-05-01

    Full Text Available This paper presents a novel wireless vibration-based method for monitoring the degree of feed filter clogging. In process industry, these filters are applied to prevent impurities entering the process. During operation, the filters gradually become clogged, decreasing the feed flow and, in the worst case, preventing it. The cleaning of the filter should therefore be carried out predictively in order to avoid equipment damage and unnecessary process downtime. The degree of clogging is estimated by first calculating the time domain indices from low frequency accelerometer samples and then taking the median of the processed values. Nine different statistical quantities are compared based on the estimation accuracy and criteria for operating in resource-constrained environments with particular focus on energy efficiency. The initial results show that the method is able to detect the degree of clogging, and the approach may be applicable to filter clogging monitoring.

  16. Long-term behaviour of concrete under saline conditions for long-term stable sealing structures; Langzeitverhalten von Beton unter salinaren Bedingungen fuer langzeitstabile Verschlussbauwerke

    Energy Technology Data Exchange (ETDEWEB)

    Dahlhaus, Frank; Haucke, Joerg [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Bergbau und Spezialtiefbau

    2012-03-15

    The authors of the contribution under consideration examine the long-term behaviour of concrete under saline conditions and in particular the suitability of the dam construction materials salt concrete and brine concrete for the use as a part of a sealing system of long-term stable geotechnical sealing structures. The long-term stability of the building material mainly is determined by the corrosion of the cement paste phases. The specific shrinkage behaviour of the construction material is analyzed experimentally in order to verify the expected cracks. The mechanisms of cracking in the salt concrete and brine concrete are analyzed by means of a mesomechanical approach in numerical finite-element calculations.

  17. Gaussian Plume Model Parameters for Ground-Level and Elevated Sources Derived from the Atmospheric Diffusion Equation in the Neutral and Stable Conditions

    International Nuclear Information System (INIS)

    Essa, K.S.M.

    2009-01-01

    The analytical solution of the atmospheric diffusion equation for a point source gives the ground-level concentration profiles. It depends on the wind speed ua nd vertical dispersion coefficient σ z expressed by Pasquill power laws. Both σ z and u are functions of downwind distance, stability and source elevation, while for the ground-level emission u is constant. In the neutral and stable conditions, the Gaussian plume model and finite difference numerical methods with wind speed in power law and the vertical dispersion coefficient in exponential law are estimated. This work shows that the estimated ground-level concentrations of the Gaussian model for high-level source and numerical finite difference method are very match fit to the observed ground-level concentrations of the Gaussian model

  18. Collecting conditions usage metadata to optimize current and future ATLAS software and processing

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00064378; The ATLAS collaboration; Formica, Andrea; Gallas, Elizabeth; Oda, Susumu; Rinaldi, Lorenzo; Rybkin, Grigori; Verducci, Monica

    2017-01-01

    Conditions data (for example: alignment, calibration, data quality) are used extensively in the processing of real and simulated data in ATLAS. The volume and variety of the conditions data needed by different types of processing are quite diverse, so optimizing its access requires a careful understanding of conditions usage patterns. These patterns can be quantified by mining representative log files from each type of processing and gathering detailed information about conditions usage for that type of processing into a central repository.

  19. Stable isotope signatures in bulk samples from two soils with contrasting characteristics. What do they tell about ongoing pedogenic processes?

    Science.gov (United States)

    Jiménez-Morillo, Nicasio T.; dos Anjos Leal, Otávio; Knicker, Heike; Pinheiro Dick, Deborah; González-Vila, Francisco J.; González-Pérez, José A.

    2014-05-01

    Isotopic ratio mass spectrometry (IRMS) has been proven as a promising tool for the monitoring of biogeochemical processes in soil. In this work, stable isotope signatures of light elements δ15N, δ13C, δ18O and δD were determined for two soils with contrasting characteristics in terms of climate, vegetation, land use and management. The studied soils were a Cambisol from a subtropical area (Paraná region, South Brazil) and an Arenosol from a Mediterranean climate (Andalusia, South Spain). A Flash 2000 HT (N, C, S, H and O) elemental analyzer (Thermo Scientific) coupled to a Delta V Advantage IRMS (Thermo Scientific) was used. Isotopic ratios are reported as parts per thousand (o ) deviations from appropriate standards recognized by the international atomic energy agency (IAEA). In a first approach we took advantage of the well-known different δ13C signature between plants using either the C4 or C3 carbon fixation pathway (O'Leary, 1981). The Arenosol (Spain) revealed a δ13C signature which is clearly in the range of C3 plants (-26 to -30 o ). Different plant canopies (tree, shrubs or ferns) caused only slight variations δ13C (STD= 0.98). In contrast, the Cambisol (Brazil) showed less depletion of the heavier carbon isotope corresponding to C4 predominant vegetation. In addition an increase from -19 o in the soil surface (0 - 5 cm) to -16 o in the subsoil (20 - 30 cm) was observed in line with a recent (2 years old) shift of the land use from the predominant C4 grassland to eucalypt (C3) cultivation. Crossplots of δ15N vs. δ18O may provide information about nitrate (NO3-) sources and N cycling (Kendall, 1998). In the Mediterranean Arenosol this signal (δ18O = 30o δ15N = 2o ) was found compatible with a predominant nitrate atmospheric deposition, whereas the signal in the Brazilian Cambisol pointed to the use of a mineral N fertilization with signs of denitrification processes (δ18O = 13o δ15N = 9o ). No conclusive results could be obtained from the

  20. Solid radwaste processing and conditioning. The SGN experience

    International Nuclear Information System (INIS)

    Tucoulat, D.; Tchemitcheff, E.

    1993-01-01

    Solid wastes are generated in the operation of the installations in France. These solid wastes display different levels of radioactivity. Some of them arising from research centres or reprocessing plants even contain relatively significant quantities of alpha-bearing radionuclides. In order to produce an ultimate waste package that satisfies the requirements set by safety authorities and the organizations in charge of final waste disposal in the concerned countries, solid waste conditioning takes place in a number of successive steps

  1. Correlated initial condition for an embedded process by time partitioning

    Czech Academy of Sciences Publication Activity Database

    Velický, Bedřich; Kalvová, Anděla; Špička, Václav

    2010-01-01

    Roč. 81, č. 23 (2010), 235116/1-235116/12 ISSN 1098-0121 R&D Projects: GA ČR GA202/08/0361 Institutional research plan: CEZ:AV0Z10100520; CEZ:AV0Z10100521 Keywords : non-equilibrium * Initial conditions * decay of correlations * Green's functions * quantum transport equations Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.772, year: 2010

  2. Anterior process calcaneal fractures: a systematic evaluation of associated conditions

    Energy Technology Data Exchange (ETDEWEB)

    Petrover, David [NYU Hospital for Joint Disease, Radiology Department, New York, NY (United States); Hopital Beaujon, Service de Radiologie, Paris (France); Schweitzer, Mark E. [NYU Hospital for Joint Disease, Radiology Department, New York, NY (United States); Laredo, J.D. [Hopital Lariboisiere, Service de Radiologie, Paris (France)

    2007-07-15

    The objective was to evaluate the association, by MRI, of anterior calcaneal process fractures with tarsal coalitions, ankle sprains, and bifurcate ligament abnormalities. A retrospective review of 1,479 foot and ankle MR images was performed, over a period of 5 years, for isolated anterior process fractures of the calcaneus. Fifteen 1.5-T MR examinations were systematically evaluated by two radiologists in consensus. Marrow edema patterns, presence of a calcaneonavicular coalition, as well as bifurcate and anterior talofibular ligaments, were evaluated. There were 15 fractures of the anterior calcaneal process with an incidence of 1%. The average patient age was 51 years (range 25-82). Twelve patients were women and 3 were men. The majority of the fractures (14 out of 15) presented as an edema pattern on T2-weighted images, either diffuse (9 out of 15), or vertical (5 out of 15). One case did not show marrow edema, but rather a hypointense line. Nine patients (60%) demonstrated calcaneonavicular coalition and anterior calcaneal process fracture. In 6 patients (50%) the anterior talofibular ligament (ATFL) was thickened. Three patients did not have axial images, and were classified as non-conclusive for the ATFL evaluation. The bifurcate ligament was thickened with hyperintense signal demonstrating a sprain in 9 out of 13 (69%). Only 2 patients (16.5%) had an anterior calcaneal process fracture without any associated abnormality. We believe that there is a probable association of anterior process fractures and calcaneonavicular coalitions. We also feel, based on our results and the prior literature that there is likely also an association with both ATFL injuries and bifurcate ligament injuries. (orig.)

  3. Anterior process calcaneal fractures: a systematic evaluation of associated conditions

    International Nuclear Information System (INIS)

    Petrover, David; Schweitzer, Mark E.; Laredo, J.D.

    2007-01-01

    The objective was to evaluate the association, by MRI, of anterior calcaneal process fractures with tarsal coalitions, ankle sprains, and bifurcate ligament abnormalities. A retrospective review of 1,479 foot and ankle MR images was performed, over a period of 5 years, for isolated anterior process fractures of the calcaneus. Fifteen 1.5-T MR examinations were systematically evaluated by two radiologists in consensus. Marrow edema patterns, presence of a calcaneonavicular coalition, as well as bifurcate and anterior talofibular ligaments, were evaluated. There were 15 fractures of the anterior calcaneal process with an incidence of 1%. The average patient age was 51 years (range 25-82). Twelve patients were women and 3 were men. The majority of the fractures (14 out of 15) presented as an edema pattern on T2-weighted images, either diffuse (9 out of 15), or vertical (5 out of 15). One case did not show marrow edema, but rather a hypointense line. Nine patients (60%) demonstrated calcaneonavicular coalition and anterior calcaneal process fracture. In 6 patients (50%) the anterior talofibular ligament (ATFL) was thickened. Three patients did not have axial images, and were classified as non-conclusive for the ATFL evaluation. The bifurcate ligament was thickened with hyperintense signal demonstrating a sprain in 9 out of 13 (69%). Only 2 patients (16.5%) had an anterior calcaneal process fracture without any associated abnormality. We believe that there is a probable association of anterior process fractures and calcaneonavicular coalitions. We also feel, based on our results and the prior literature that there is likely also an association with both ATFL injuries and bifurcate ligament injuries. (orig.)

  4. Stable isotopes

    International Nuclear Information System (INIS)

    Evans, D.K.

    1986-01-01

    Seventy-five percent of the world's stable isotope supply comes from one producer, Oak Ridge Nuclear Laboratory (ORNL) in the US. Canadian concern is that foreign needs will be met only after domestic needs, thus creating a shortage of stable isotopes in Canada. This article describes the present situation in Canada (availability and cost) of stable isotopes, the isotope enrichment techniques, and related research programs at Chalk River Nuclear Laboratories (CRNL)

  5. Stable isotopes labelled compounds

    International Nuclear Information System (INIS)

    1982-09-01

    The catalogue on stable isotopes labelled compounds offers deuterium, nitrogen-15, and multiply labelled compounds. It includes: (1) conditions of sale and delivery, (2) the application of stable isotopes, (3) technical information, (4) product specifications, and (5) the complete delivery programme

  6. Three-ring stable oxygen isotope ratios indicating cooler and wetter climate conditions and high flood frequency periods in the Red River Basin, Manitoba, Canada

    International Nuclear Information System (INIS)

    Buhay, W.M.; Harms, P.; Marcino, D.; Mayer, B.; St. George, S.; Nielsen, E.

    2002-01-01

    In the Red River region of southern Manitoba, Canada, the frequency of flood events tends to increase during cooler and wetter climate conditions. Predictably, recorded Red River flood stages are primarily a result of meteorological conditions which produce an increase runoff due to excess snowmelt and heavy spring precipitation. Winter skewed precipitation periods corresponding to cooler and wetter conditions in the Red River Basin may provide traceable oxygen isotope signals in hydrologically sensitive trees occupying the basin. To test this hypothesis, three overlapping oak tree-ring chronologies (KPO1: 1990 to 1795; STVO1: 1985 to 1797; STVO2: 1990 to 1845) were annually sampled and processed for their cellulose

  7. Psychology of Personality in the Conditions of Modern Migration Processes

    Science.gov (United States)

    Artemyeva, Tatiana V.; Chernov, Sergey A.

    2016-01-01

    The relevance of the research problem due to the fact that, together with a positive influence on the demographic situation, the consequences of migration processes have a negative impact in all areas of social life and become a source of social tension and destabilization of the economic and political situation. The purpose of the article is to…

  8. Cylindric process algebras with conditionals give substitutionless $ p $ CRL

    NARCIS (Netherlands)

    S.P. Luttik (Bas)

    1999-01-01

    textabstract Theories that are designed to reason about processes and the information they exchange usually also include a construction to quantify over this information. We mention the input prefix mechanism of, e.g., the $pi$-calculus and the operation $gsum{$ for alternative quantification over

  9. Research of Polyacrylonitrile Saponification Heterophase Process Mechanism in Different Conditions

    OpenAIRE

    Oral K. Beisenbayev; Aziza B. Isa; Anastasya E. Kovaleva

    2015-01-01

    Kinetic regularities of polyacrylonitrile saponification in aqueous, aqueous-alcoholic solutions of alkali and weight were defined. At the same time the environment influence on the kinetics of the process of polyacrylonitrile saponification, the role of diffusion and adsorption saponified agent to the surface of macromolecules as well as the ability to control the depth and degree of saponification hydrophilic product were determined.

  10. Managing complexity in process digitalisation with dynamic condition response graphs

    DEFF Research Database (Denmark)

    Hildebrandt, Thomas; Debois, Søren; Slaats, Tijs

    2017-01-01

    . Sadly, it is also witnessed by a number of expensive failed digitalisation projects. In this paper we point to two key problems in state-of-The art BPM technologies: 1) the use of rigid flow diagrams as the "source code" of process digitalisation is not suitable for managing the complexity of knowledge...

  11. Modeling of hydrologic conditions and solute movement in processed oil shale waste embankments under simulated climatic conditions

    International Nuclear Information System (INIS)

    Reeves, T.L.; Turner, J.P.; Hasfurther, V.R.; Skinner, Q.D.

    1992-06-01

    The scope of this program is to study interacting hydrologic, geotechnical, and chemical factors affecting the behavior and disposal of combusted processed oil shale. The research combines bench-scale testing with large scale research sufficient to describe commercial scale embankment behavior. The large scale approach was accomplished by establishing five lysimeters, each 7.3 x 3.0 x 3.0 m deep, filled with processed oil shale that has been retorted and combusted by the Lurgi-Ruhrgas (Lurgi) process. Approximately 400 tons of Lurgi processed oil shale waste was provided by RBOSC to carry out this study. Research objectives were designed to evaluate hydrologic, geotechnical, and chemical properties and conditions which would affect the design and performance of large-scale embankments. The objectives of this research are: assess the unsaturated movement and redistribution of water and the development of potential saturated zones and drainage in disposed processed oil shale under natural and simulated climatic conditions; assess the unsaturated movement of solubles and major chemical constituents in disposed processed oil shale under natural and simulated climatic conditions; assess the physical and constitutive properties of the processed oil shale and determine potential changes in these properties caused by disposal and weathering by natural and simulated climatic conditions; assess the use of previously developed computer model(s) to describe the infiltration, unsaturated movement, redistribution, and drainage of water in disposed processed oil shale; evaluate the stability of field scale processed oil shale solid waste embankments using computer models

  12. Signal Conditioning in Process of High Speed Imaging

    Directory of Open Access Journals (Sweden)

    Libor Hargas

    2015-01-01

    Full Text Available The accuracy of cinematic analysis with camera system depends on frame rate of used camera. Specific case of cinematic analysis is in medical research focusing on microscopic objects moving with high frequencies (cilia of respiratory epithelium. The signal acquired by high speed video acquisition system has very amount of data. This paper describes hardware parts, signal condition and software, which is used for image acquiring thru digital camera, intelligent illumination dimming hardware control and ROI statistic creation. All software parts are realized as virtual instruments.

  13. Methods and Conditions for Achieving Continuous Improvement of Processes

    OpenAIRE

    Florica BADEA; Catalina RADU; Ana-Maria GRIGORE

    2010-01-01

    In the early twentieth century, the Taylor model improved, in a spectacular maner the efficiency of the production processes. This allowed obtaining high productivity by low-skilled workers, but used in large number in the execution of production. Currently this model is questioned by experts and was replaced by the concept of "continuous improvement". The first signs of change date from the '80s, with the apparition of quality circles and groups of operators on quality issues, principles whi...

  14. Physical exercise, inflammatory process and adaptive condition: an overview

    OpenAIRE

    Silva, Fernando Oliveira Catanho da; Macedo, Denise Vaz

    2011-01-01

    Physical exercise induces inflammation, a physiological response that is part of immune system activity and promotes tissue remodeling after exercise overload. The activation of the inflammatory process is local and systemic and is mediated by different cells and secreted compounds. The objective is to reestablish organ homeostasis after a single bout of exercise or after several exercise sessions. The acute-phase response involves the combined actions of activated leukocytes, cytokines, acut...

  15. Organic solution-processible electroluminescent molecular glasses for non-doped standard red OLEDs with electrically stable chromaticity

    Energy Technology Data Exchange (ETDEWEB)

    Bi, Xiaoman; Zuo, Weiwei; Liu, Yingliang, E-mail: liuylxn@sohu.com; Zhang, Zhenru; Zeng, Cen; Xu, Shengang; Cao, Shaokui, E-mail: caoshaokui@zzu.edu.cn

    2015-10-15

    Highlights: • The D–A–D electroluminescent molecular glasses are synthesized. • Non-doped red electroluminescent film is fabricated by spin-coating. • Red OLED shows stable wavelength, luminous efficiency and chromaticity. • CIE1931 coordinate is in accord with standard red light in PAL system. - Abstract: Organic light-emitting molecular glasses (OEMGs) are synthesized through the introduction of nonplanar donor and branched aliphatic chain into electroluminescent emitters. The target OEMGs are characterized by {sup 1}H NMR, {sup 13}C NMR, IR, UV–vis and fluorescent spectra as well as elemental analysis, TG and DSC. The results indicated that the optical, electrochemical and electroluminescent properties of OEMGs are adjusted successfully by the replacement of electron-donating group. The non-doped OLED device with a standard red electroluminescent emission is achieved by spin-coating the THF solution of OEMG with a triphenylamine moiety. This non-doped red OLED device takes on an electrically stable electroluminescent performance, including the stable maximum electroluminescent wavelength of 640 nm, the stable luminous efficiency of 2.4 cd/A and the stable CIE1931 coordinate of (x, y) = (0.64, 0.35), which is basically in accord with the CIE1931 coordinate (x, y) = (0.64, 0.33) of standard red light in PAL system.

  16. Magnetic manipulation device for the optimization of cell processing conditions.

    Science.gov (United States)

    Ito, Hiroshi; Kato, Ryuji; Ino, Kosuke; Honda, Hiroyuki

    2010-02-01

    Variability in human cell phenotypes make it's advancements in optimized cell processing necessary for personalized cell therapy. Here we propose a strategy of palm-top sized device to assist physically manipulating cells for optimizing cell preparations. For the design of such a device, we combined two conventional approaches: multi-well plate formatting and magnetic cell handling using magnetite cationic liposomes (MCLs). From our previous works, we showed the labeling applications of MCL on adhesive cells for various tissue engineering approaches. To feasibly transfer cells in multi-well plate, we here evaluated the magnetic response of MCL-labeled suspension type cells. The cell handling performance of Jurkat cells proved to be faster and more robust compared to MACS (Magnetic Cell Sorting) bead methods. To further confirm our strategy, prototype palm-top sized device "magnetic manipulation device (MMD)" was designed. In the device, the actual cell transportation efficacy of Jurkat cells was satisfying. Moreover, as a model of the most distributed clinical cell processing, primary peripheral blood mononuclear cells (PBMCs) from different volunteers were evaluated. By MMD, individual PBMCs indicated to have optimum Interleukin-2 (IL-2) concentrations for the expansion. Such huge differences of individual cells indicated that MMD, our proposing efficient and self-contained support tool, could assist the feasible and cost-effective optimization of cell processing in clinical facilities. Copyright (c) 2009 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  17. Dual stable isotopes of CH 4 from Yellowstone hot-springs suggest hydrothermal processes involving magmatic CO 2

    Energy Technology Data Exchange (ETDEWEB)

    Moran, James J.; Whitmore, Laura M.; Jay, Zackary J.; Jennings, Ryan deM.; Beam, Jacob P.; Kreuzer, Helen W.; Inskeep, William P.

    2017-07-01

    Volcanism and post-magmatism contribute both significant annual CH4 fluxes to the atmosphere (on par with other natural sources such as forest fire and wild animal emissions) and have been implicated in past climate-change events. The Yellowstone hot spot is one of the largest volcanic systems on Earth and is known to emit methane in addition to other greenhouse gases (e.g. carbon dioxide) but the ultimate source of this methane flux has not been elucidated. Here we use dual stable isotope analysis (δ2H and δ13C) of CH4(g) sampled from ten high-temperature geothermal pools in Yellowstone National Park to show that the predominant flux of CH4(g) is abiotic. The average δ13C and δ2H values of CH4(g) emitted from hot springs (-26.7 (±2.4) and -236.9 (±12.0) ‰, respectively) are not consistent with biotic (microbial or thermogenic) methane sources, but are within previously reported ranges for abiotic methane production. Correlation between δ13CCH4 and δ13C-dissolved inorganic C (DIC) also suggests that CO2 is a parent C source for the observed CH4(g). Moreover, CH4-CO2 isotopic geothermometry was used to estimate CH4(g) formation temperatures ranging from ~ 250 - 350°C, which is just below the temperature estimated for the hydrothermal reservoir and consistent with the hypothesis that subsurface, rock-water interactions are responsible for large methane fluxes from this volcanic system. An understanding of conditions leading to the abiotic production of methane and associated isotopic signatures are central to understanding the evolutionary history of deep carbon sources on Earth.

  18. Unconditionally stable methods for simulating multi-component two-phase interface models with Peng-Robinson equation of state and various boundary conditions

    KAUST Repository

    Kou, Jisheng

    2015-03-01

    In this paper, we consider multi-component dynamic two-phase interface models, which are formulated by the Cahn-Hilliard system with Peng-Robinson equation of state and various boundary conditions. These models can be derived from the minimum problems of Helmholtz free energy or grand potential in the realistic thermodynamic systems. The resulted Cahn-Hilliard systems with various boundary conditions are fully coupled and strongly nonlinear. A linear transformation is introduced to decouple the relations between different components, and as a result, the models are simplified. From this, we further propose a semi-implicit unconditionally stable time discretization scheme, which allows us to solve the Cahn-Hilliard system by a decoupled way, and thus, our method can significantly reduce the computational cost and memory requirements. The mixed finite element methods are employed for the spatial discretization, and the approximate errors are also analyzed for both space and time. Numerical examples are tested to demonstrate the efficiency of our proposed methods. © 2015 Elsevier B.V.

  19. Hawkes-diffusion process and the conditional probability of defaults in the Eurozone

    Science.gov (United States)

    Kim, Jungmu; Park, Yuen Jung; Ryu, Doojin

    2016-05-01

    This study examines market information embedded in the European sovereign CDS (credit default swap) market by analyzing the sovereign CDSs of 13 Eurozone countries from January 1, 2008, to February 29, 2012, which includes the recent Eurozone debt crisis period. We design the conditional probability of defaults for the CDS prices based on the Hawkes-diffusion process and obtain the theoretical prices of CDS indexes. To estimate the model parameters, we calibrate the model prices to empirical prices obtained from individual sovereign CDS term structure data. The estimated parameters clearly explain both cross-sectional and time-series data. Our empirical results show that the probability of a huge loss event sharply increased during the Eurozone debt crisis, indicating a contagion effect. Even countries with strong and stable economies, such as Germany and France, suffered from the contagion effect. We also find that the probability of small events is sensitive to the state of the economy, spiking several times due to the global financial crisis and the Greek government debt crisis.

  20. Research on Heat Exchange Process in Aircraft Air Conditioning System

    Science.gov (United States)

    Chichindaev, A. V.

    2017-11-01

    Using of heat-exchanger-condenser in the air conditioning system of the airplane Tu-204 (Boeing, Airbus, Superjet 100, MS-21, etc.) for cooling the compressed air by the cold air with negative temperature exiting the turbine results in a number of operational problems. Mainly it’s frosting of the heat exchange surface, which is the cause of live-section channels frosting, resistance increasing and airflow in the system decreasing. The purpose of this work is to analyse the known freeze-up-fighting methods for heat-exchanger-condenser, description of the features of anti-icing protection and offering solutions to this problem. For the problem of optimizing the design of heat exchangers in this work used generalized criterion that describes the ratio of thermal resistances of cold and hot sections, which include: the ratio of the initial values of heat transfer agents flow state; heat exchange surface finning coefficients; factors which describes the ratio of operating parameters and finning area. By controlling the ratio of the thermal resistances can be obtained the desired temperature of the heat exchange surface, which would prevent freezing. The work presents the results of a numerical study of the effect of different combinations of regime and geometrical factors changes on reduction of the heat-exchanger-condenser freezing surface area, including using of variable ratio of thermal resistances.

  1. Optimization of the caldasite processing conditions by alcaline melting

    International Nuclear Information System (INIS)

    Brown, A.E.P.

    1976-01-01

    A study has been done to recover economically the uranium and zirconium values of the ores at Pocos de Caldas Plateau in the state of Minas Gerais, Brazil. In a preliminar study, it was investigated the opening of the ore by alcaline fusion that were carried out in a temperature controlled furnace and the variables studied were the time, temperature and NaOH/ore ratio. The optimization procedure was based on the steepest Ascent Method developed by Box and Wilson, utilizing a complete 2 3 factorial design. The analysis of the data indicated the response optimum for the process in: time 1.52 +-0.1 hour; temperature 805 +-15degC; NaOH/ore ratio 1.7 ton/ton. Solubilizations higher than 97%ZrO 2 and recuperations nearly of 100%U 3 O 8 are obtained arouns this point [pt

  2. Finite element simulation of ironing process under warm conditions

    Directory of Open Access Journals (Sweden)

    Swadesh Kumar Singh

    2014-01-01

    Full Text Available Metal forming is one of the most important steps in manufacturing of a large variety of products. Ironing in deep drawing is done by adjusting the clearance between the punch and the die and allow the material flow over the punch. In the present investigation effect of extent of ironing behavior on the characteristics of the product like thickness distribution with respect to temperature was studied. With the help of finite element simulation using explicit finite element code LS-DYNA the stress in the drawn cup were predicted in the drawn cup. To increase the accuracy in the simulation process, numbers of integration points were increased in the thickness direction and it was found that there is very close prediction of finite element results to that of experimental ones.

  3. Stable Boundary Layer Issues

    NARCIS (Netherlands)

    Steeneveld, G.J.

    2012-01-01

    Understanding and prediction of the stable atmospheric boundary layer is a challenging task. Many physical processes are relevant in the stable boundary layer, i.e. turbulence, radiation, land surface coupling, orographic turbulent and gravity wave drag, and land surface heterogeneity. The

  4. Photochemical processes and ozone production in Finnish conditions

    Energy Technology Data Exchange (ETDEWEB)

    Laurila, T.; Hakola, H. [Finnish Meteorological Inst., Helsinki (Finland). Air Quality Dept.

    1996-12-31

    Photochemical ozone production is observed in March-September. Highest ozone concentrations and production efficiencies are observed in spring in the northern parts and in summer in the southern parts of the country. VOC concentrations are relatively low compared to continental areas in general. During the growing season a substantial part of the total reactive mass of VOCs is of biogenic origin. Large forest areas absorb ozone substantially, decreasing the ambient ozone concentrations in central and northern parts of Finland where long-range transport of ozone is relatively important compared to local production. The aim of the work conducted at Finnish Meteorological Institute has been to characterise concentrations of photochemically active species in the boundary layer and their photochemical formation and deposition including the effects on vegetation. Also interactions between the boundary layer and free troposphere of ozone have been studied. In the future, fluxes of both biogenic species and air pollutants will be measured and the models will be further developed so that the photochemical and micrometeorological processes could be better understood

  5. Continuous fermentative hydrogen production in different process conditions

    Energy Technology Data Exchange (ETDEWEB)

    Nasirian, N. [Islamic Azad Univ., Shoushtar (Iran, Islamic Republic of). Dept. of Agricultural Mechanization; Almassi, M.; Minaee, S. [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Dept. of Agricultural Mechanization; Widmann, R. [Duisburg-Essen Univ., Essen (Germany). Dept. of Environmental Engineering, Waste and Water

    2010-07-01

    This paper reported on a study in which hydrogen was produced by fermentation of biomass. A continuous process using a non-sterile substrate with a readily available mixed microflora was used on heat treated digested sewage sludge from a wastewater treatment plant. Hydrogen was produced from waste sugar at a pH of 5.2 and a temperature of 37 degrees C. An experimental setup of three 5.5 L working volume continuously stirred tank reactors (CSTR) in different stirring speeds were constructed and operated at 7 different hydraulic retention times (HRTs) and different organic loading rates (OLR). Dissolved organic carbon was examined. The results showed that the stirring speed of 135 rpm had a beneficial effect on hydrogen fermentation. The best performance was obtained in 135 rpm and 8 h of HRT. The amount of gas varied with different OLRs, but could be stabilized on a high level. Methane was not detected when the HRT was less than 16 h. The study identified the reactor in which the highest specific rate of hydrogen production occurred.

  6. Photochemical processes and ozone production in Finnish conditions

    Energy Technology Data Exchange (ETDEWEB)

    Laurila, T; Hakola, H [Finnish Meteorological Inst., Helsinki (Finland). Air Quality Dept.

    1997-12-31

    Photochemical ozone production is observed in March-September. Highest ozone concentrations and production efficiencies are observed in spring in the northern parts and in summer in the southern parts of the country. VOC concentrations are relatively low compared to continental areas in general. During the growing season a substantial part of the total reactive mass of VOCs is of biogenic origin. Large forest areas absorb ozone substantially, decreasing the ambient ozone concentrations in central and northern parts of Finland where long-range transport of ozone is relatively important compared to local production. The aim of the work conducted at Finnish Meteorological Institute has been to characterise concentrations of photochemically active species in the boundary layer and their photochemical formation and deposition including the effects on vegetation. Also interactions between the boundary layer and free troposphere of ozone have been studied. In the future, fluxes of both biogenic species and air pollutants will be measured and the models will be further developed so that the photochemical and micrometeorological processes could be better understood

  7. The influence of external conditions on the grain storage process

    Directory of Open Access Journals (Sweden)

    O. A. Orlovtseva

    2016-01-01

    Full Text Available .High quality grain - a pledge of his safety, reduce losses and the costs of storage. Wheat is the main source of human nutrition. Elements contained in wheat perform a fundamental role in human life. Storing grain quality is an urgent task. One of the labor-intensive operations in this process is the correct placement of parties in wheat granary and timely monitoring of key parameters (humidity and temperature. In this regard, we consider methods for determining the intensity of the grain breathing method for determining the moisture content and temperature of the grain of wheat. Humidity was determined by electrical hygrometer. To measure the temperature of wheat used mercury thermometer. In analyzing the breathing wheat energy depending on the humidity it was found that the intensity of respiration increasingly affects humidity increase than an increase in temperature. As objects of study used wheat varieties: Hordeiforme 432 and Multiroom 321. According to the results obtained in the study plot the respiratory activity of the grain from moisture. According to the schedules we concluded that the sharp increase in wheat breathing energy occurs with increasing moisture content to a value of more than 15%. Just found out that in addition to breathing in highly humid grain appears vital functions of harmful microorganisms, which under the influence of grain rots and becomes stale. Thus, ho-well-organized and skilled observation, the correct analysis of the obtained data allow to bring the maximum reduction in spending of dry matter and therefore achieve lower grain weight loss during storage.

  8. A meta-analysis of motivational interviewing process: Technical, relational, and conditional process models of change.

    Science.gov (United States)

    Magill, Molly; Apodaca, Timothy R; Borsari, Brian; Gaume, Jacques; Hoadley, Ariel; Gordon, Rebecca E F; Tonigan, J Scott; Moyers, Theresa

    2018-02-01

    In the present meta-analysis, we test the technical and relational hypotheses of Motivational Interviewing (MI) efficacy. We also propose an a priori conditional process model where heterogeneity of technical path effect sizes should be explained by interpersonal/relational (i.e., empathy, MI Spirit) and intrapersonal (i.e., client treatment seeking status) moderators. A systematic review identified k = 58 reports, describing 36 primary studies and 40 effect sizes (N = 3,025 participants). Statistical methods calculated the inverse variance-weighted pooled correlation coefficient for the therapist to client and the client to outcome paths across multiple target behaviors (i.e., alcohol use, other drug use, other behavior change). Therapist MI-consistent skills were correlated with more client change talk (r = .55, p technical hypothesis was supported. Specifically, proportion MI consistency was related to higher proportion change talk (r = .11, p = .004) and higher proportion change talk was related to reductions in risk behavior at follow up (r = -.16, p technical hypothesis path effect sizes was partially explained by inter- and intrapersonal moderators. This meta-analysis provides additional support for the technical hypothesis of MI efficacy; future research on the relational hypothesis should occur in the field rather than in the context of clinical trials. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

  9. Stable long-term pulmonary function after fludarabine, antithymocyte globulin and i.v. BU for reduced-intensity conditioning allogeneic SCT.

    Science.gov (United States)

    Dirou, S; Malard, F; Chambellan, A; Chevallier, P; Germaud, P; Guillaume, T; Delaunay, J; Moreau, P; Delasalle, B; Lemarchand, P; Mohty, M

    2014-05-01

    Lung function decline is a well-recognized complication following allogeneic SCT (allo-SCT). Reduced-intensity conditioning (RIC) and in vivo T-cell depletion by administration of antithymocyte globulin (ATG) may have a protective role in the occurrence of late pulmonary complications. This retrospective study reported the evolution of lung function parameters within the first 2 years after allo-SCT in a population receiving the same RIC regimen that included fludarabine and i.v. BU in combination with low-dose ATG. The median follow-up was 35.2 months. With a median age of 59 years at the time of transplant, at 2 years, the cumulative incidences of non-relapse mortality was as low as 9.7%. The cumulative incidence of relapse was 33%. At 2 years, the cumulative incidences of extensive chronic GVHD (cGVHD) and of pulmonary cGVHD were 23.1% and 1.9%, respectively. The cumulative incidences of airflow obstruction and restrictive pattern were 3.8% and 9.6%, respectively. Moreover, forced expiratory volume (FEV1), forced vital capacity (FVC) and FEV1/FVC ratio remained stable from baseline up to 2 years post transplantation (P=0.26, P=0.27 and P=0.07, respectively). These results correspond favorably with the results obtained with other RIC regimens not incorporating ATG, and suggest that ATG may have a protective pulmonary role after allo-SCT.

  10. Effects of steam-heating processes on a stratified volcanic aquifer: Stable isotopes and dissolved gases in thermal waters of Vulcano Island (Aeolian archipelago)

    Science.gov (United States)

    Federico, C.; Capasso, G.; Paonita, A.; Favara, R.

    2010-05-01

    We report on a comprehensive study of major-ion chemistry, dissolved gases, and stable isotopes measured in water wells at Vulcano Island since 1988. The work focuses on a quantitative model describing steam condensation and boiling phenomena in shallow water bodies. The model is based on the differences in partition coefficients between liquid water and vapor characterizing oxygen and hydrogen isotopes, as well as volcanic gases (CO 2, S species, and HCl). Based on both physical conditions of aquifers identified during drilling campaigns and the composition of the volcanic vapor, mass and enthalpy balances are applied in a multistep process of steam separation and condensation in shallower aquifers. By comparing the model results with measured data, we infer that (i) strong isotope enrichment observed in some shallow thermal waters can result from an increasing mass rate of condensing deep vapor, even in water meteoric in origin; (ii) the high CO 2 content measured in the fumarolic vapor during 1988-1993 affected the δ18O value of the steam-heated water due to CO 2-H 2O isotope exchange; (iii) the high pCO 2 measured in the coldest and peripheral waters are explained by the progressive enrichment of this gas in the vapor phase during multistep boiling; and (iv) the high Cl - and SO 42-contents in the hottest waters can be attributed to the direct condensation (single-step) of volcanic vapor. The model also takes into account both the mass fluxes and the compositions of the involved endmembers (steam and shallow groundwater), which provides important inferences on the modifications observed or expected during periods of increasing mass and heat input from depth.

  11. Unpredictably Stable

    DEFF Research Database (Denmark)

    Failla, Virgilio; Melillo, Francesca; Reichstein, Toke

    2014-01-01

    Is entrepreneurship a more stable career choice for high employment turnover individuals? We find that a transition to entrepreneurship induces a shift towards stayer behavior and identify job matching, job satisfaction and lock-in effects as main drivers. These findings have major implications...

  12. Structural Composite Supercapacitors: Electrical and Mechanical Impact of Separators and Processing Conditions

    Science.gov (United States)

    2013-09-01

    Structural Composite Supercapacitors : Electrical and Mechanical Impact of Separators and Processing Conditions by Edwin B. Gienger, James F...Proving Ground, MD 21005-5066 ARL-TR-6624 September 2013 Structural Composite Supercapacitors : Electrical and Mechanical Impact of...2012 4. TITLE AND SUBTITLE Structural Composite Supercapacitors : Electrical and Mechanical Impact of Separators and Processing Conditions 5a

  13. Extending In Vitro Conditioning in "Aplysia" to Analyze Operant and Classical Processes in the Same Preparation

    Science.gov (United States)

    Brembs, Bjorn; Baxter, Douglas A.; Byrne, John H.

    2004-01-01

    Operant and classical conditioning are major processes shaping behavioral responses in all animals. Although the understanding of the mechanisms of classical conditioning has expanded significantly, the understanding of the mechanisms of operant conditioning is more limited. Recent developments in "Aplysia" are helping to narrow the gap in the…

  14. Research on the intermediate process of a free-piston linear generator from cold start-up to stable operation: Numerical model and experimental results

    International Nuclear Information System (INIS)

    Feng, Huihua; Guo, Chendong; Jia, Boru; Zuo, Zhengxing; Guo, Yuyao; Roskilly, Tony

    2016-01-01

    Highlights: • The intermediate process of free-piston linear generator is investigated for the first time. • “Gradually switching strategy” is the best strategy in the intermediate process. • Switching at the top dead center position timing has the least influences on free-piston linear generator. • After the intermediate process, the operation parameters value is smaller than those before the intermediate process. - Abstract: The free-piston linear generator (FPLG) has more merits than the traditional reciprocating engines (TRE), and has been under extensive investigation. Researchers mainly investigated on the starting process and the stable generating process of FPLG, while there has not been any report on the intermediate process from the engine cold start-up to stable operation process. Therefore, this paper investigated the intermediate process of the FPLG in terms of switching strategy and switching position based on simulation results and test results. Results showed that when the motor force of the linear electric machine (LEM) declined gradually from 100% to 0% with an interval of 50%, and then to a resistance force in the opposite direction of piston velocity (generator mode), the operation parameters of the FPLG showed minimal changes. Meanwhile, the engine operated more smoothly when the LEM switched its working mode from a motor to a generator at the piston dead center, compared with that at the middle stroke or a random switching time. More importantly, after the intermediate process, the operation parameters of FPLG were smaller than that before the intermediate process. As a result, a gradual motor/generator switching strategy was recommended and the LEM was suggested to switch its working mode when the piston arrived its dead center in order to achieve smooth engine operation.

  15. Development of novel CO{sub 2}-stable oxygen permeable dual phase membranes for CO{sub 2} capture in an oxy-fuel process

    Energy Technology Data Exchange (ETDEWEB)

    Luo, Huixia

    2012-07-19

    The combustion of fossil fuels in power stations with pure oxygen following the oxy-fuel process allows the Sequestration of CO{sub 2}. The pure oxygen needed can be separated from air by oxygen transporting ceramics like single phase perovskites. However, most of the so far developed single phase perovskites have stability problems in a CO{sub 2} containing atmosphere. Dual phase membranes are micro-scale mixtures of an electron conducting phase and an oxygen ion conducting phase and their compositions can be tailored according to practical requirements, which are considered to be promising substitutes for the single phase perovskite materials. In my thesis the issues of phase stability for perovskite-type material with the common composition Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 3-{delta}} (BSCF) as weil as the development of a series of novel CO{sub 2}-stable dual phase membranes were studied. In Chapter 2, the phase stability and permeation behavior of a dead-end BSCF tube membrane in high-purity oxygen at temperatures below 750 C, were elucidated using powder X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDXS), high-angle annular dark-field (HAADF) and scanning transmission electron microscopy (STEM). lt was found that parts of the cubic perovskite BSCF transformed into a hexagonal perovskite Ba{sub 0.5{+-}x}Sr{sub 0.5{+-}x}CoO{sub 3-{delta}} (x {approx} 0.1) and a trigonal mixed oxide Ba{sub 1-x}Sr{sub x}CO{sub 2-y}Fe{sub y}O{sub 5{+-}{delta}} (x {approx} 0.15, y {approx} 0.25) in high-purity oxygen at 750 C. On the other hand, it was found that the partial degradation of cubic BSCF perovskite at 750 C was more pronounced under the strongly oxidizing conditions on the oxygen supply (feed) side than on the oxygen release (permeate) side of the membrane. The structural instability of BSCF is attributed to an oxidation of cobalt from Co{sup 2+} to Co{sup 3+} and Co{sup 4+}, which exhibits an ionic radius that is too small to be tolerated by

  16. The choice of process parameters to obtain a stable dispersion system of plant-based bioactivated dicotyledonous seeds

    Directory of Open Access Journals (Sweden)

    L. A. Samofalova

    2016-01-01

    Full Text Available The article dealswith the search for the unification of technological approaches to increase the efficiency of separation of the protein complex and stability of the plant foundations from seed dicotyledonous economically important crops of soybean, hemp, buckwheat. Uneven localization of nitrogenous substances in the seed largely determines the accessibility of protein complexes for extraction. Natural fermentation of spare proteins in cellular structures when the germination process starts leads to the accumulation of soluble nitrogen, and the change in the salt composition of protoplasm facilitates the transition in the solution of insoluble complexes in the form of colloids. It is shown that fine grinding of dry seeds increases the efficiency of extraction by 1.3–1.6 times, while rough grinding increases bioactivity by 1.6–1.8 times. The dispersion containing 8.1±0.7% of dry matter at buckwheat bases and 9.5±1,3% at hemp and soy bases with the water ratio 1:4 to 1:7 satisfy the requirements of taste sensations and fullness of the chemical composition. Based on the results of the extraction of protein of buckwheat seeds the conclusion has been drawn that there is a need for a differentiated approach to selecting conditions for the creation of food framework. Taking into consideration the fact that the amount of calcium in buckwheat seeds is17–25 times smaller than in oil seeds and the quantity of phosphorus is 1.6–2 times smaller, the contribution of electrostatic forces in the protein solubility is small and the additional actions to activate the protein complex are required. To predict the properties of vegetable bases of bioactivated soybean seeds and hemp, the central composite uniform-rotatable planning was applied and the full factorial experiment with factorial scheme 3×3×3 (33 was selected. The preferred combination of values of the input parameters X1, X2, X3 was discovered. They provide for the maximum of Y

  17. Stable particles

    International Nuclear Information System (INIS)

    Samios, N.P.

    1993-01-01

    I have been asked to review the subject of stable particles, essentially the particles that eventually comprised the meson and baryon octets. with a few more additions -- with an emphasis on the contributions made by experiments utilizing the bubble chamber technique. In this activity, much work had been done by the photographic emulsion technique and cloud chambers-exposed to cosmic rays as well as accelerator based beams. In fact, many if not most of the stable particles were found by these latter two techniques, however, the forte of the bubble chamber (coupled with the newer and more powerful accelerators) was to verify, and reinforce with large statistics, the existence of these states, to find some of the more difficult ones, mainly neutrals and further to elucidate their properties, i.e., spin, parity, lifetimes, decay parameters, etc

  18. Influence of organic carbon sources and isotope exchange processes between water and nitrate on the fractionation of the stable isotopes 15N/14N and 18O/16O in dissolved nitrate during microbial dentrification in groundwater

    International Nuclear Information System (INIS)

    Wunderlich, Anja A.L.

    2012-01-01

    Stable isotopes of nitrate are commonly used to determine sources and degradation of nitrate. In this study, nitrite oxidizing bacteria were found to promote an oxygen isotope exchange between water and nitrate under anoxic conditions. Also, different carbon sources were found to influence the enrichment of stable isotopes in nitrate during microbial denitrification. Both results refine the stable isotope model of nitrate in respect to nitrate source determination and microbial nitrate reduction.

  19. Strategy for research on radioactive waste processing and conditioning in France

    International Nuclear Information System (INIS)

    Cavedon, J.M.; Tallec, M.

    2001-01-01

    Research on radioactive medium level waste processing and conditioning aims at offering processing routes for waste forms and materials of potential value that are not yet provided easy handling by existing industrial processes. These studies are mandatory under the Dec 31, 1991 law and are coordinated by CEA. The strategy relies on the completion and rationalization of the existing processing routes, within acceptable technical and economic limits. Waste processing techniques aim at reducing the volume and the chemical diversity of medium activity waste, and are based on incineration-vitrification. Conditioning techniques call for high performance matrices and standardized containers, the latter keeping an ability to contain bulk waste. (author)

  20. Qualification of R.A. waste conditioning process and installations by ONDRAF/NIRAS

    International Nuclear Information System (INIS)

    Havard, P.; Faniel, L.; Voet, M.; Goeyse, A. de.

    1993-01-01

    ONDRAF/NIRAS in its role of national agency responsible for the management of radioactive waste in Belgium (including transport, intermediate storage and final disposal of the conditioned waste) has defined and enforces conditions for the acceptance (i.e. taking over) of conditioned waste packages. The waste acceptance conditions applicable at the present time are: 1. The conditioning process and installations are qualified by ONDRAF/NIRAS; 2. The waste packages are produced according to the qualified process and installations, and meet the technical specifications and acceptance criteria defined by ONDRAF/NIRAS; 3. The production of the waste packages is supervised by ONDRAF/NIRAS through an inspection and control programme specific to each conditioning process and associated installation, and has been found satisfactory. (author)

  1. The stable isotopic composition of water vapour above Corsica during the HyMeX SOP1 campaign: insight into vertical mixing processes from lower-tropospheric survey flights

    Science.gov (United States)

    Sodemann, Harald; Aemisegger, Franziska; Pfahl, Stephan; Bitter, Mark; Corsmeier, Ulrich; Feuerle, Thomas; Graf, Pascal; Hankers, Rolf; Hsiao, Gregor; Schulz, Helmut; Wieser, Andreas; Wernli, Heini

    2017-05-01

    Stable isotopes of water vapour are powerful indicators of meteorological processes on a broad range of scales, reflecting evaporation, condensation, and air mass mixing processes. With the recent advent of fast laser-based spectroscopic methods, it has become possible to measure the stable isotopic composition of atmospheric water vapour in situ at a high temporal resolution. Here we present results from such comprehensive airborne spectroscopic isotope measurements in water vapour over the western Mediterranean at a high spatial and temporal resolution. Measurements have been acquired by a customized Picarro L2130-i cavity-ring down spectrometer deployed onboard the Dornier 128 D-IBUF aircraft together with a meteorological flux measurement package during the HyMeX SOP1 (Hydrological cycle in Mediterranean Experiment special observation period 1) field campaign in Corsica, France, during September and October 2012. Taking into account memory effects of the air inlet pipe, the typical time resolution of the measurements was about 15-30 s, resulting in an average horizontal resolution of about 1-2 km. Cross-calibration of the water vapour measurements from all humidity sensors showed good agreement under most flight conditions but the most turbulent ones. In total 21 successful stable isotope flights with 59 flight hours have been performed. Our data provide quasi-climatological autumn average conditions and vertical profiles of the stable isotope parameters δD, δ18O, and d-excess during the study period. A d-excess minimum in the overall average profile is reached in the region of the boundary-layer top, possibly caused by precipitation evaporation. This minimum is bracketed by higher d-excess values near the surface caused by non-equilibrium fractionation, and a maximum above the boundary layer related to the increasing d-excess in very depleted and dry high-altitude air masses. Repeated flights along the same pattern reveal pronounced day-to-day variability

  2. Nucleation and growth process of sodalite and cancrinite from kaolinite-rich clay under low-temperature hydrothermal conditions

    Directory of Open Access Journals (Sweden)

    Carlos Alberto Ríos Reyes

    2013-04-01

    Full Text Available The synthesis of low-silica zeotypes by hydrothermal transformation of kaolinite-rich clay and the nucleation and growth processes of sodalite and cancrinite in the system Na2O-Al2O3-SiO2-H2O at 100 °C were investigated. The synthesis products were characterized by X-ray powder diffraction (XRPD, scanning electron microscopy (SEM, Fourier transform infrared spectroscopy (FT-IR, 29Si and 27Al Magic Angle Spinning Nuclear Magnetic Resonance (MAS-NMR and thermogravimetric analysis (TGA. Our data show that the sequence of the transformation of phases is: Poorly crystalline aluminosilicate → zeolite LTA → sodalite → sodalite + cancrinite → cancrinite. Synthesized materials appeared stable thermodynamically under the experimental conditions, with zeolite LTA (a metastable phase occurring as a minor phase, compared with the presence of sodalite and cancrinite.

  3. Distinct requirements for signal peptidase processing and function in the stable signal peptide subunit of the Junin virus envelope glycoprotein

    International Nuclear Information System (INIS)

    York, Joanne; Nunberg, Jack H.

    2007-01-01

    The arenavirus envelope glycoprotein (GP-C) retains a cleaved and stable signal peptide (SSP) as an essential subunit of the mature complex. This 58-amino-acid residue peptide serves as a signal sequence and is additionally required to enable transit of the assembled GP-C complex to the Golgi, and for pH-dependent membrane fusion activity. We have investigated the C-terminal region of the Junin virus SSP to study the role of the cellular signal peptidase (SPase) in generating SSP. Site-directed mutagenesis at the cleavage site (positions - 1 and - 3) reveals a pattern of side-chain preferences consistent with those of SPase. Although position - 2 is degenerate for SPase cleavage, this residue in the arenavirus SSP is invariably a cysteine. In the Junin virus, this cysteine is not involved in disulfide bonding. We show that replacement with alanine or serine is tolerated for SPase cleavage but prevents the mutant SSP from associating with GP-C and enabling transport to the cell surface. Conversely, an arginine mutation at position - 1 that prevents SPase cleavage is fully compatible with GP-C-mediated membrane fusion activity when the mutant SSP is provided in trans. These results point to distinct roles of SSP sequences in SPase cleavage and GP-C biogenesis. Further studies of the unique structural organization of the GP-C complex will be important in identifying novel opportunities for antiviral intervention against arenaviral hemorrhagic disease

  4. Stable isotope compositions of serpentinite seamounts in the Mariana forearc: Serpentinization processes, fluid sources and sulfur metasomatism

    Science.gov (United States)

    Alt, J.C.; Shanks, Wayne C.

    2006-01-01

    The Mariana and Izu-Bonin arcs in the western Pacific are characterized by serpentinite seamounts in the forearc that provide unique windows into the mantle wedge. We present stable isotope (O, H, S, and C) data for serpentinites from Conical seamount in the Mariana forearc and S isotope data for Torishima seamount in the Izu-Bonin forearc in order to understand the compositions of fluids and temperatures of serpentinization in the mantle wedge, and to investigate the transport of sulfur from the slab to the mantle wedge. Six serpentine mineral separates have a restricted range of ??18O (6.5-8.5???). Antigorite separates have ??D values of -29.5??? to -45.5??? that reflect serpentinization within the mantle wedge whereas chrysotile has low ??D values (-51.8??? to -84.0???) as the result of re-equilibration with fluids at low temperatures. Fractionation of oxygen isotopes between serpentine and magnetite indicate serpentinization temperatures of 300-375 ??C. Two late cross-fiber chrysotile veins have higher ??18O values of 8.9??? to 10.8??? and formed at lower temperatures (as low as ???100 ??C). Aqueous fluids in equilibrium with serpentine at 300-375 ??C had ??18O = 6.5-9??? and ??D = -4??? to -26???, consistent with sediment dehydration reactions at temperatures arc lavas. ?? 2006 Elsevier B.V. All rights reserved.

  5. Recovery process of wall condition in KSTAR vacuum vessel after temporal machine-vent for repair

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kwang Pyo, E-mail: kpkim@nfri.er.ke; Hong, Suk-Ho; Lee, Hyunmyung; Song, Jae-in; Jung, Nam-Yong; Lee, Kunsu; Chu, Yong; Kim, Hakkun; Park, Kaprai; Oh, Yeong-Kook

    2015-10-15

    Highlights: • Efforts have been made to obtain vacuum condition that is essential for the plasma experiments. • For example, the vacuum vessel should be vented to repair in-vessel components such as diagnostic shutter, and PFC damaged by high energy plasma. • Here, we present the recovery process of wall condition in KSTAR after temporal machine-vent for repair. • It is found that an acceptable vacuum condition has been achieved only by plasma based wall conditioning techniques such as baking, GDC, and boronization. • This study was that the proper recovering method of the vacuum condition should be developed according to the severity of the accident. - Abstract: Efforts have been made to obtain vacuum condition that is essential for the plasma experiments. Under certain situations, for example, the vacuum vessel should be vented to repair in-vessel components such as diagnostic shutter, exchange of window for diagnostic equipment, and PFC damaged by high energy plasma. For the quick restart of the campaign, a recovery process was established to make the vacuum condition acceptable for the plasma experiment. In this paper, we present the recovery process of wall condition in KSTAR after temporal machine-vent for repair. It is found that an acceptable vacuum condition has been achieved only by plasma based wall conditioning techniques such as baking, GDC, and boronization. This study was that the proper recovering method of the vacuum condition should be developed according to the severity of the accident.

  6. Optimization Of PVDF-TrFE Processing Conditions For The Fabrication Of Organic MEMS Resonators.

    Science.gov (United States)

    Ducrot, Pierre-Henri; Dufour, Isabelle; Ayela, Cédric

    2016-01-21

    This paper reports a systematic optimization of processing conditions of PVDF-TrFE piezoelectric thin films, used as integrated transducers in organic MEMS resonators. Indeed, despite data on electromechanical properties of PVDF found in the literature, optimized processing conditions that lead to these properties remain only partially described. In this work, a rigorous optimization of parameters enabling state-of-the-art piezoelectric properties of PVDF-TrFE thin films has been performed via the evaluation of the actuation performance of MEMS resonators. Conditions such as annealing duration, poling field and poling duration have been optimized and repeatability of the process has been demonstrated.

  7. Effect of processing conditions on quality of green beans subjected to reciprocating agitation thermal processing.

    Science.gov (United States)

    Singh, Anika; Singh, Anubhav Pratap; Ramaswamy, Hosahalli S

    2015-12-01

    The effect of reciprocating agitation thermal processing (RA-TP) on quality of canned beans was evaluated in a lab-scale reciprocating retort. Green beans were selected due to their soft texture and sensitive color. Green beans (2.5cm length×0.8cm diameter) were filled into 307×409 cans with carboxylmethylcellulose (0-2%) solutions and processed at different temperatures (110-130°C) and reciprocation frequency (1-3Hz) for predetermined heating times to achieve a process lethality (F o ) of 10min. Products processed at higher temperatures and higher reciprocation frequencies resulted in better retention of chlorophyll and antioxidant activity. However, high reciprocation frequency also resulted in texture losses, with higher breakage of beans, increased turbidity and higher leaching. There was total loss of product quality at the highest agitation speed, especially with low viscosity covering solutions. Results suggest that reciprocating agitation frequency needs to be adequately moderated to get the best quality. For getting best quality, particularly for canned liquid particulate foods with soft particulates and those susceptible to high impact agitation, a gentle reciprocating motion (~1Hz) would be a good compromise. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Stable optical frequency comb generation and applications in arbitrary waveform generation, signal processing and optical data mining

    Science.gov (United States)

    Ozharar, Sarper

    This thesis focuses on the generation and applications of stable optical frequency combs. Optical frequency combs are defined as equally spaced optical frequencies with a fixed phase relation among themselves. The conventional source of optical frequency combs is the optical spectrum of the modelocked lasers. In this work, we investigated alternative methods for optical comb generation, such as dual sine wave phase modulation, which is more practical and cost effective compared to modelocked lasers stabilized to a reference. Incorporating these comblines, we have generated tunable RF tones using the serrodyne technique. The tuning range was +/-1 MHz, limited by the electronic waveform generator, and the RF carrier frequency is limited by the bandwidth of the photodetector. Similarly, using parabolic phase modulation together with time division multiplexing, RF chirp extension has been realized. Another application of the optical frequency combs studied in this thesis is real time data mining in a bit stream. A novel optoelectronic logic gate has been developed for this application and used to detect an 8 bit long target pattern. Also another approach based on orthogonal Hadamard codes have been proposed and explained in detail. Also novel intracavity modulation schemes have been investigated and applied for various applications such as (a) improving rational harmonic modelocking for repetition rate multiplication and pulse to pulse amplitude equalization, (b) frequency skewed pulse generation for ranging and (c) intracavity active phase modulation in amplitude modulated modelocked lasers for supermode noise spur suppression and integrated jitter reduction. The thesis concludes with comments on the future work and next steps to improve some of the results presented in this work.

  9. Modeling of hydrologic conditions and solute movement in processed oil shale waste embankments under simulated climatic conditions

    International Nuclear Information System (INIS)

    Turner, J.P.; Hasfurther, V.

    1992-01-01

    The scope of the research program and the continuation is to study interacting hydrologic, geotechnical, and chemical factors affecting the behavior and disposal of combusted processed oil shale. The research combines bench-scale testing with large scale research sufficient to describe commercial scale embankment behavior. The large scale approach was accomplished by establishing five lysimeters, each 7.3 x 3.0 x 3.0 m deep, filled with processed oil shale that has been retorted and combusted by the Lurgi-Ruhrgas (Lurgi) process. Approximately 400 tons of Lurgi processed oil shale waste was provided by Rio Blanco Oil Shale Co., Inc. (RBOSC) through a separate cooperative agreement with the University of Wyoming (UW) to carry out this study. Three of the lysimeters were established at the RBOSC Tract C-a in the Piceance Basin of Colorado. Two lysimeters were established in the Environmental Simulation Laboratory (ESL) at UW. The ESL was specifically designed and constructed so that a large range of climatic conditions could be physically applied to the processed oil shale which was filled in the lysimeter cells

  10. Modeling of hydrologic conditions and solute movement in processed oil shale waste embankments under simulated climatic conditions

    International Nuclear Information System (INIS)

    Turner, J.P.; Reeves, T.L.; Skinner, Q.D.; Hasfurther, V.

    1992-11-01

    The scope of the original research program and of its continuation is to study interacting hydrologic, geotechnical, and chemical factors affecting the behavior and disposal of combusted processed oil shale. The research combines bench-scale testing with large-scale testing sufficient to describe commercial-scale embankment behavior. The large-scale testing was accomplished by constructing five lysimeters, each 7.3x3.0x3.0 m deep, filled with processed oil shale that has been retorted and combusted by the Lurgi-Ruhrgas (Lurgi) process (Schmalfield 1975). Approximately 400 tons of Lurgi processed oil shale waste was provided by Rio Blanco Oil Shale Co., Inc. to carry out this study. Three of the lysimeters were established at the RBOSC Tract C-a in the Piceance Basin near Rifle, Colorado. Two lysimeters were established in the Environmental Simulation Laboratory (ESL) at UW. The ESL was specifically designed and constructed so that a large range of climatic conditions could be physically applied to the processed oil shale which was placed in the lysimeter cells. This report discusses and summarizes results from scientific efforts conducted between October 1991 and September 1992 for Fiscal Year 1992

  11. Stable isotopes

    International Nuclear Information System (INIS)

    Brazier, J.L.; Guinamant, J.L.

    1995-01-01

    According to the progress which has been realised in the technology of separating and measuring isotopes, the stable isotopes are used as preferable 'labelling elements' for big number of applications. The isotopic composition of natural products shows significant variations as a result of different reasons like the climate, the seasons, or their geographic origins. So, it was proved that the same product has a different isotopic composition of alimentary and agriculture products. It is also important in detecting the pharmacological and medical chemicals. This review article deals with the technology, like chromatography and spectrophotometry, adapted to this aim, and some important applications. 17 refs. 6 figs

  12. Stable Tetraquarks

    Energy Technology Data Exchange (ETDEWEB)

    Quigg, Chris [Fermilab

    2018-04-13

    For very heavy quarks, relations derived from heavy-quark symmetry imply novel narrow doubly heavy tetraquark states containing two heavy quarks and two light antiquarks. We predict that double-beauty states will be stable against strong decays, whereas the double-charm states and mixed beauty+charm states will dissociate into pairs of heavy-light mesons. Observing a new double-beauty state through its weak decays would establish the existence of tetraquarks and illuminate the role of heavy color-antitriplet diquarks as hadron constituents.

  13. THE STUDY OF DIRECTED FERMENTATION PROCESS USING STRAINS OF LACTIC ACID BACTERIA FOR OBTAINING VEGETABLE PRODUCTS OF STABLE QUALITY

    Directory of Open Access Journals (Sweden)

    V. V. Kondratenko

    2016-01-01

    Full Text Available The objective of the research was to study the process of directed fermentation of whitehead cabbage variety ‘Slava’, using strains of lactic acid bacteria and their consortium with the degree of their mutual influence. As strains of lactic acid bacteria, we have chosen the following: VCR 536 Lactobacillus casei, Lactobacillus plantarum VKM V-578. To obtain comparable results, all experiments were performed on model mediums. For the first time we studied the dynamics of changes in quality indicators at the process of directed fermentation using strains of lactic acid bacteria (LAB including their consortiums. The mathematical model developed adequately describes the degree of destruction of glucose and fructose in the fermentation process. The raw material was undergone to homogenization and sterilization with the aim to create optimal conditionsfor the development of the target microorganisms and to detect the degree of  restruction of fructose and glucose by different strains of microorganisms. The mathematical model developed adequately described the degree of destruction of fructose and glucose in the treatment process. The use of a consortium of lactic acid bacteria (L. plantarum+L. casei to this culture medium is shown to be impractical. The addition of fructose in quantity 0.5% to weight of the model medium enabled to intensify significantly the process of white cabbage fermentation.

  14. Theoretical Background for the Decision-Making Process Modelling under Controlled Intervention Conditions

    Directory of Open Access Journals (Sweden)

    Bakanauskienė Irena

    2017-12-01

    Full Text Available This article is intended to theoretically justify the decision-making process model for the cases, when active participation of investing entities in controlling the activities of an organisation and their results is noticeable. Based on scientific literature analysis, a concept of controlled conditions is formulated, and using a rational approach to the decision-making process, a model of the 11-steps decision-making process under controlled intervention is presented. Also, there have been unified conditions, describing the case of controlled interventions thus providing preconditions to ensure the adequacy of the proposed decision-making process model.

  15. iMS2Flux – a high–throughput processing tool for stable isotope labeled mass spectrometric data used for metabolic flux analysis

    Directory of Open Access Journals (Sweden)

    Poskar C Hart

    2012-11-01

    Full Text Available Abstract Background Metabolic flux analysis has become an established method in systems biology and functional genomics. The most common approach for determining intracellular metabolic fluxes is to utilize mass spectrometry in combination with stable isotope labeling experiments. However, before the mass spectrometric data can be used it has to be corrected for biases caused by naturally occurring stable isotopes, by the analytical technique(s employed, or by the biological sample itself. Finally the MS data and the labeling information it contains have to be assembled into a data format usable by flux analysis software (of which several dedicated packages exist. Currently the processing of mass spectrometric data is time-consuming and error-prone requiring peak by peak cut-and-paste analysis and manual curation. In order to facilitate high-throughput metabolic flux analysis, the automation of multiple steps in the analytical workflow is necessary. Results Here we describe iMS2Flux, software developed to automate, standardize and connect the data flow between mass spectrometric measurements and flux analysis programs. This tool streamlines the transfer of data from extraction via correction tools to 13C-Flux software by processing MS data from stable isotope labeling experiments. It allows the correction of large and heterogeneous MS datasets for the presence of naturally occurring stable isotopes, initial biomass and several mass spectrometry effects. Before and after data correction, several checks can be performed to ensure accurate data. The corrected data may be returned in a variety of formats including those used by metabolic flux analysis software such as 13CFLUX, OpenFLUX and 13CFLUX2. Conclusion iMS2Flux is a versatile, easy to use tool for the automated processing of mass spectrometric data containing isotope labeling information. It represents the core framework for a standardized workflow and data processing. Due to its flexibility

  16. Stable Inverted Low-Bandgap Polymer Solar Cells with Aqueous Solution Processed Low-Temperature ZnO Buffer Layers

    Directory of Open Access Journals (Sweden)

    Chunfu Zhang

    2016-01-01

    Full Text Available Efficient inverted low-bandgap polymer solar cells with an aqueous solution processed low-temperature ZnO buffer layer have been investigated. The low-bandgap material PTB-7 is employed so that more solar light can be efficiently harvested, and the aqueous solution processed ZnO electron transport buffer layer is prepared at 150°C so that it can be compatible with the roll-to-roll process. Power conversion efficiency (PCE of the inverted device reaches 7.12%, which is near the control conventional device. More importantly, the inverted device shows a better stability, keeping more than 90% of its original PCE after being stored for 625 hours, while PCE of the conventional device is only 75% of what it was. In addition, it is found that the ZnO thin film annealed in N2 can obviously increase PCE of the inverted device further to 7.26%.

  17. Materials Characterisation of Glass/epoxy Composites - Focusing on Process Conditions

    DEFF Research Database (Denmark)

    Jakobsen, Johnny; Lyckegaard, Anders; Jensen, Erik Appel

    2013-01-01

    Predicting the behaviour of fibre reinforced polymer composites taking the process conditions into account involves advanced modelling techniques and an extensive materials characterisation. The materials characterisation of a chopped strand mat glass/epoxy composite has been the focus...

  18. LabData database sub-systems for post-processing and quality control of stable isotope and gas chromatography measurements

    Science.gov (United States)

    Suckow, A. O.

    2013-12-01

    Measurements need post-processing to obtain results that are comparable between laboratories. Raw data may need to be corrected for blank, memory, drift (change of reference values with time), linearity (dependence of reference on signal height) and normalized to international reference materials. Post-processing parameters need to be stored for traceability of results. State of the art stable isotope correction schemes are available based on MS Excel (Geldern and Barth, 2012; Gröning, 2011) or MS Access (Coplen, 1998). These are specialized to stable isotope measurements only, often only to the post-processing of a special run. Embedding of algorithms into a multipurpose database system was missing. This is necessary to combine results of different tracers (3H, 3He, 2H, 18O, CFCs, SF6...) or geochronological tools (Sediment dating e.g. with 210Pb, 137Cs), to relate to attribute data (submitter, batch, project, geographical origin, depth in core, well information etc.) and for further interpretation tools (e.g. lumped parameter modelling). Database sub-systems to the LabData laboratory management system (Suckow and Dumke, 2001) are presented for stable isotopes and for gas chromatographic CFC and SF6 measurements. The sub-system for stable isotopes allows the following post-processing: 1. automated import from measurement software (Isodat, Picarro, LGR), 2. correction for sample-to sample memory, linearity, drift, and renormalization of the raw data. The sub-system for gas chromatography covers: 1. storage of all raw data 2. storage of peak integration parameters 3. correction for blank, efficiency and linearity The user interface allows interactive and graphical control of the post-processing and all corrections by export to and plot in MS Excel and is a valuable tool for quality control. The sub-databases are integrated into LabData, a multi-user client server architecture using MS SQL server as back-end and an MS Access front-end and installed in four

  19. Stable beams

    CERN Multimedia

    2015-01-01

    Stable beams: two simple words that carry so much meaning at CERN. When LHC page one switched from "squeeze" to "stable beams" at 10.40 a.m. on Wednesday, 3 June, it triggered scenes of jubilation in control rooms around the CERN sites, as the LHC experiments started to record physics data for the first time in 27 months. This is what CERN is here for, and it’s great to be back in business after such a long period of preparation for the next stage in the LHC adventure.   I’ve said it before, but I’ll say it again. This was a great achievement, and testimony to the hard and dedicated work of so many people in the global CERN community. I could start to list the teams that have contributed, but that would be a mistake. Instead, I’d simply like to say that an achievement as impressive as running the LHC – a machine of superlatives in every respect – takes the combined effort and enthusiasm of everyone ...

  20. Stable isotope compositions of serpentinite seamounts in the Mariana forearc: Serpentinization processes, fluid sources and sulfur metasomatism

    Science.gov (United States)

    Alt, J.C.; Shanks, Wayne C.

    2006-01-01

    The Mariana and Izu-Bonin arcs in the western Pacific are characterized by serpentinite seamounts in the forearc that provide unique windows into the mantle wedge. We present stable isotope (O, H, S, and C) data for serpentinites from Conical seamount in the Mariana forearc and S isotope data for Torishima seamount in the Izu-Bonin forearc in order to understand the compositions of fluids and temperatures of serpentinization in the mantle wedge, and to investigate the transport of sulfur from the slab to the mantle wedge. Six serpentine mineral separates have a restricted range of ??18O (6.5-8.5???). Antigorite separates have ??D values of -29.5??? to -45.5??? that reflect serpentinization within the mantle wedge whereas chrysotile has low ??D values (-51.8??? to -84.0???) as the result of re-equilibration with fluids at low temperatures. Fractionation of oxygen isotopes between serpentine and magnetite indicate serpentinization temperatures of 300-375 ??C. Two late cross-fiber chrysotile veins have higher ??18O values of 8.9??? to 10.8??? and formed at lower temperatures (as low as ???100 ??C). Aqueous fluids in equilibrium with serpentine at 300-375 ??C had ??18O = 6.5-9??? and ??D = -4??? to -26???, consistent with sediment dehydration reactions at temperatures aragonite veins in metabasalt and siltstone clasts within the serpentinite flows have ??18O = 16.7-24.5???, consistent with the serpentinizing fluids at temperatures <250 ??C. ??13C values of 0.1-2.5??? suggest a source in subducting carbonate sediments. The ??34S values of sulfide in serpentinites on Conical Seamount (-6.7??? to 9.8???) result from metasomatism through variable reduction of aqueous sulfate (??34S = 14???) derived from slab sediments. Despite sulfur metasomatism, serpentinites have low sulfur contents (generally < 164 ppm) that reflect the highly depleted nature of the mantle wedge. The serpentinites are mostly enriched in 34S (median ??34Ssulfide = 4.5???), consistent with a 34S

  1. Attentional processing of input in explicit and implicit learning conditions : an eye-tracking study

    OpenAIRE

    Indrarathne, Bimali; Kormos, Judit

    2017-01-01

    In this study we examined language learners’ attentional processing of a target syntactic construction in written L2 input in different input conditions, the change in learners’ knowledge of the targeted construction in these conditions and the relationship between the change in knowledge and attentional processing. 100 L2 learners of English in Sri Lanka were divided into four experimental groups and control group: input flood, input enhancement, a specific instruction to pay attention to th...

  2. Computational fluid dynamics modeling of bun baking process under different oven load conditions.

    Science.gov (United States)

    Tank, A; Chhanwal, N; Indrani, D; Anandharamakrishnan, C

    2014-09-01

    A computational fluid dynamics (CFD) model was developed to study the temperature profile of the bun during baking process. Evaporation-condensation mechanism and effect of the latent heat during phase change of water was incorporated in this model to represent actual bun baking process. Simulation results were validated with experimental measurements of bun temperature at two different positions. Baking process is completed within 20 min, after the temperature of crumb become stable at 98 °C. Further, this study was extended to investigate the effect of partially (two baking trays) loaded and fully loaded (eight baking trays) oven on temperature profile of bun. Velocity and temperature profile differs in partially loaded and fully loaded oven. Bun placed in top rack showed rapid baking while bun placed in bottom rack showed slower baking due to uneven temperature distribution in the oven. Hence, placement of bun inside the oven affects temperature of bun and consequently, the quality of the product.

  3. Large-area processing of solution type metal-oxide in TFT backplanes and integration in highly stable OLED displays

    NARCIS (Netherlands)

    Marinkovic, Marko; Takata, Ryo; Neumann, Anita; Pham, Duy Vu; Anselmann, Ralf; Maas, Joris; Van Der Steen, Jan Laurens; Gelinck, Gerwin; Katsouras, Ilias

    2017-01-01

    Solution type metal-oxide semiconductor was processed on mass-production ready equipment and integrated in a backplane with ESL architecture TFTs. Excellent thickness uniformity of the semiconductor layer was obtained over the complete Gen I glass substrate (320 mm ×00D7; 352 mm), resulting in

  4. Smoothed Conditional Scale Function Estimation in AR(1-ARCH(1 Processes

    Directory of Open Access Journals (Sweden)

    Lema Logamou Seknewna

    2018-01-01

    Full Text Available The estimation of the Smoothed Conditional Scale Function for time series was taken out under the conditional heteroscedastic innovations by imitating the kernel smoothing in nonparametric QAR-QARCH scheme. The estimation was taken out based on the quantile regression methodology proposed by Koenker and Bassett. And the proof of the asymptotic properties of the Conditional Scale Function estimator for this type of process was given and its consistency was shown.

  5. Grapes from the geographical areas of the Black Sea: Agroclimatic growing conditions and evaluation of stable isotopes compositions in scientific study

    Directory of Open Access Journals (Sweden)

    Kolesnov Alexander

    2016-01-01

    Full Text Available The report considers the agroclimatic conditions in the Black Sea districts of cultivation and processing of grapes - the Black Sea Lowland, the Crimean Peninsula and the South-west coastal areas of the Greater Caucasus. The IRMS/SIRA techniques - Flash combustion (FC-IRMS/SIRA & Isotopic equilibration (EQ-IRMS/SIRA - were first applied for the evaluation of carbon and oxygen isotopes ratios in the components of grapes from the Crimean Peninsula. The 13C/12C ratios were studied by the FC-IRMS/SIRA in carbohydrates and organic acids in authentic samples of 8 grape varieties from the 2015 harvest. The EQ-IRMS/SIRA was applied to measure the 18O/16O ratios in intracellular water of grapes. The measured δ13CVPDB value ranges from − 25.01 to − 21.01‰ (for carbohydrates, and from − 25.09 to − 21.30‰ (for organic acids. To evaluate the extent of biological isotope fractionation the 18O/16O ratios were measured in ground water and water of atmospheric precipitates from the Crimean Peninsula. Compared to ground (δ18OVSMOW from − 10.85 to − 8.14‰ and atmospheric (average δ18OVSMOW− 2.85‰ waters, the intracellular water of Crimean grape varieties is found to be enriched with 18O isotope. The δ18OVSMOW value of the grape intracellular water varies from 2.34 to 5.29‰ according to agroclimatic conditions of the season in 2015.

  6. The prediction of mechanical performance of isotactic polypropylene on the basis of processing conditions

    NARCIS (Netherlands)

    Caelers, H.J.M.; Govaert, L.E.; Peters, G.W.M.

    2016-01-01

    A strategy is presented to predict the yield kinetics following from different thermomechanical histories experienced during processing in non-isothermal quiescent conditions. This strategy deals with three main parts, i.e. processing, structure and properties. In the first part the applied cooling

  7. Pedagogical conditions of maintenance of integrity of process of socialization-individualization of children-orphans

    OpenAIRE

    Pronina A. N.

    2011-01-01

    Formation of the high-grade person of children of preschool age, without parental support should be carried out in complete process of socialization-individualization that assumes working out of the pedagogical conditions directed on maintenance of interrelation of processes of socialization and an individualization.

  8. Measures of Dependence for α-Stable Distributed Processes and Its Application to Diagnostics of Local Damage in Presence of Impulsive Noise

    Directory of Open Access Journals (Sweden)

    Grzegorz Żak

    2017-01-01

    Full Text Available Local damage detection in rotating machinery is simply searching for cyclic impulsive signal in noisy observation. Such raw signal is mixture of various components with specific properties (deterministic, random, cyclic, impulsive, etc.. The problem appears when the investigated process is based on one of the heavy-tailed distributions. In this case the classical measure can not be considered. Therefore, alternative measures of dependence adequate for such processes should be considered. In this paper we examine the structure of dependence of alpha-stable based systems expressed by means of two measures, namely, codifference and covariation. The reason for using alpha-stable distribution is simple and intuitive: signal of interest is impulsive so its distribution is heavy-tailed. The main goal is to introduce a new technique for estimation of covariation. Due to the complex nature of such vibration signals applying novel methods instead of classical ones is recommended. Classical algorithms usually are based on the assumption that theoretical second moment is finite, which is not true in case of the data acquired on the faulty components. Main advantage of our proposed algorithm is independence from second moment assumption.

  9. Collecting conditions usage metadata to optimize current and future ATLAS software and processing

    CERN Document Server

    Barberis, Dario; The ATLAS collaboration; Gallas, Elizabeth; Oda, Susumu

    2016-01-01

    Conditions data (for example: alignment, calibration, data quality) are used extensively in the processing of real and simulated data in ATLAS. The volume and variety of the conditions data needed by different types of processing are quite diverse, so optimizing its access requires a careful understanding of conditions usage patterns. These patterns can be quantified by mining representative log files from each type of processing and gathering detailed information about conditions usage for that type of processing into a central repository. In this presentation, we describe the systems developed to collect this conditions usage metadata per job type and describe a few specific (but very different) ways in which it has been used. For example, it can be used to cull specific conditions data into a much more compact package to be used by jobs doing similar types of processing: these customized collections can then be shipped with jobs to be executed on isolated worker nodes (such as HPC farms) that have no netwo...

  10. On the tail behavior of a class of multivariate conditionally heteroskedastic processes

    DEFF Research Database (Denmark)

    Pedersen, Rasmus Søndergaard; Wintenberger, Olivier

    2017-01-01

    Conditions for geometric ergodicity of multivariate autoregressive conditional heteroskedasticity (ARCH) processes, with the so-called BEKK (Baba, Engle, Kraft, and Kroner) parametrization, are considered. We show for a class of BEKK-ARCH processes that the invariant distribution is regularly...... varying. In order to account for the possibility of different tail indices of the marginals, we consider the notion of vector scaling regular variation (VSRV), closely related to non-standard regular variation. The characterization of the tail behavior of the processes is used for deriving the asymptotic...

  11. Quality assessment of baby food made of different pre-processed organic raw materials under industrial processing conditions.

    Science.gov (United States)

    Seidel, Kathrin; Kahl, Johannes; Paoletti, Flavio; Birlouez, Ines; Busscher, Nicolaas; Kretzschmar, Ursula; Särkkä-Tirkkonen, Marjo; Seljåsen, Randi; Sinesio, Fiorella; Torp, Torfinn; Baiamonte, Irene

    2015-02-01

    The market for processed food is rapidly growing. The industry needs methods for "processing with care" leading to high quality products in order to meet consumers' expectations. Processing influences the quality of the finished product through various factors. In carrot baby food, these are the raw material, the pre-processing and storage treatments as well as the processing conditions. In this study, a quality assessment was performed on baby food made from different pre-processed raw materials. The experiments were carried out under industrial conditions using fresh, frozen and stored organic carrots as raw material. Statistically significant differences were found for sensory attributes among the three autoclaved puree samples (e.g. overall odour F = 90.72, p processed from frozen carrots show increased moisture content and decrease of several chemical constituents. Biocrystallization identified changes between replications of the cooking. Pre-treatment of raw material has a significant influence on the final quality of the baby food.

  12. Population processes with unbounded extinction rate conditioned to non-extinction

    OpenAIRE

    Champagnat, Nicolas; Villemonais, Denis

    2016-01-01

    This article studies the quasi-stationary behaviour of population processes with unbounded absorption rate, including one-dimensional birth and death processes with catastrophes and multi-dimensional birth and death processes, modeling biological populations in interaction. To handle this situation, we develop original non-linear Lyapunov criteria. We obtain the exponential convergence in total variation of the conditional distributions to a unique quasi-stationary distribution, uniformly wit...

  13. Theoretical Background for the Decision-Making Process Modelling under Controlled Intervention Conditions

    OpenAIRE

    Bakanauskienė Irena; Baronienė Laura

    2017-01-01

    This article is intended to theoretically justify the decision-making process model for the cases, when active participation of investing entities in controlling the activities of an organisation and their results is noticeable. Based on scientific literature analysis, a concept of controlled conditions is formulated, and using a rational approach to the decision-making process, a model of the 11-steps decision-making process under controlled intervention is presented. Also, there have been u...

  14. Calcium stable isotope geochemistry

    Energy Technology Data Exchange (ETDEWEB)

    Gausonne, Nikolaus [Muenster Univ. (Germany). Inst. fuer Mineralogie; Schmitt, Anne-Desiree [Strasbourg Univ. (France). LHyGeS/EOST; Heuser, Alexander [Bonn Univ. (Germany). Steinmann-Inst. fuer Geologie, Mineralogie und Palaeontologie; Wombacher, Frank [Koeln Univ. (Germany). Inst. fuer Geologie und Mineralogie; Dietzel, Martin [Technische Univ. Graz (Austria). Inst. fuer Angewandte Geowissenschaften; Tipper, Edward [Cambridge Univ. (United Kingdom). Dept. of Earth Sciences; Schiller, Martin [Copenhagen Univ. (Denmark). Natural History Museum of Denmark

    2016-08-01

    This book provides an overview of the fundamentals and reference values for Ca stable isotope research, as well as current analytical methodologies including detailed instructions for sample preparation and isotope analysis. As such, it introduces readers to the different fields of application, including low-temperature mineral precipitation and biomineralisation, Earth surface processes and global cycling, high-temperature processes and cosmochemistry, and lastly human studies and biomedical applications. The current state of the art in these major areas is discussed, and open questions and possible future directions are identified. In terms of its depth and coverage, the current work extends and complements the previous reviews of Ca stable isotope geochemistry, addressing the needs of graduate students and advanced researchers who want to familiarize themselves with Ca stable isotope research.

  15. Calcium stable isotope geochemistry

    International Nuclear Information System (INIS)

    Gausonne, Nikolaus; Schmitt, Anne-Desiree; Heuser, Alexander; Wombacher, Frank; Dietzel, Martin; Tipper, Edward; Schiller, Martin

    2016-01-01

    This book provides an overview of the fundamentals and reference values for Ca stable isotope research, as well as current analytical methodologies including detailed instructions for sample preparation and isotope analysis. As such, it introduces readers to the different fields of application, including low-temperature mineral precipitation and biomineralisation, Earth surface processes and global cycling, high-temperature processes and cosmochemistry, and lastly human studies and biomedical applications. The current state of the art in these major areas is discussed, and open questions and possible future directions are identified. In terms of its depth and coverage, the current work extends and complements the previous reviews of Ca stable isotope geochemistry, addressing the needs of graduate students and advanced researchers who want to familiarize themselves with Ca stable isotope research.

  16. Effect of Processing Conditions on Fracture Resistance and Cohesive Laws of Binderfree All-Cellulose Composites

    DEFF Research Database (Denmark)

    Goutianos, Stergios; Arévalo, R.; Sørensen, Bent F.

    2014-01-01

    molecules during the drying process. Defibrilation of the raw cellulose material is done in wet medium in a paper-like process. Panels with different refining time were tested and it was found than an increase in fibre fibrillation results in a lower fracture resistance. © 2014 Springer Science......The fracture properties of all-cellulose composites without matrix were studied using Double Cantilever Beam (DCB) sandwich specimens loaded with pure monotonically increasing bending moments, which give stable crack growth. The experiments were conducted in an environmental scanning electron...... microscope to a) perform accurate measurements of both the fracture energy for crack initiation and the fracture resistance and b) observe the microscale failure mechanisms especially in the the wake of the crack tip. Since the mechanical behaviour of the all-cellulose composites was non-linear, a general...

  17. Point processes statistics of stable isotopes: analysing water uptake patterns in a mixed stand of Aleppo pine and Holm oak

    Directory of Open Access Journals (Sweden)

    Carles Comas

    2015-04-01

    Full Text Available Aim of study: Understanding inter- and intra-specific competition for water is crucial in drought-prone environments. However, little is known about the spatial interdependencies for water uptake among individuals in mixed stands. The aim of this work was to compare water uptake patterns during a drought episode in two common Mediterranean tree species, Quercus ilex L. and Pinus halepensis Mill., using the isotope composition of xylem water (δ18O, δ2H as hydrological marker. Area of study: The study was performed in a mixed stand, sampling a total of 33 oaks and 78 pines (plot area= 888 m2. We tested the hypothesis that both species uptake water differentially along the soil profile, thus showing different levels of tree-to-tree interdependency, depending on whether neighbouring trees belong to one species or the other. Material and Methods: We used pair-correlation functions to study intra-specific point-tree configurations and the bivariate pair correlation function to analyse the inter-specific spatial configuration. Moreover, the isotopic composition of xylem water was analysed as a mark point pattern. Main results: Values for Q. ilex (δ18O = –5.3 ± 0.2‰, δ2H = –54.3 ± 0.7‰ were significantly lower than for P. halepensis (δ18O = –1.2 ± 0.2‰, δ2H = –25.1 ± 0.8‰, pointing to a greater contribution of deeper soil layers for water uptake by Q. ilex. Research highlights: Point-process analyses revealed spatial intra-specific dependencies among neighbouring pines, showing neither oak-oak nor oak-pine interactions. This supports niche segregation for water uptake between the two species.

  18. Radiation processing for safe, shelf-stable and ready-to-eat food. Proceedings of a final research co-ordination meeting

    International Nuclear Information System (INIS)

    2003-01-01

    The increasingly busy lifestyles of populations in many countries have driven the demand for safe, convenient and ready-to-eat food. Traditional food processes such as drying, canning or refrigeration offer a partial solution to this demand as the sensory quality of such food may be significantly affected or the products may be contaminated by pathogenic bacteria during preparation. For developing countries, safe shelf-stable food without the need for refrigeration would offer advantages. In addition, the increasing number of immuno-compromised populations in many countries requires a new approach to food safety to meet their needs. Irradiation offers a potential to enhance microbiological safety and quality of food through shelf-life extension. The benefits of irradiation as a sanitary treatment of many types of food are well known, some of which are applied commercially in several countries. Little data were available, however, on the effect of irradiation on minimally processed food and composite food including prepared meals. A Co-ordinated Research Project (CRP) on the Development of Safe, Shelf-Stable and Ready-to-Eat Food through Radiation Processing therefore was implemented by the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture in 1996 to evaluate the role of irradiation for such food. The results were encouraging as irradiation offers promise as a sanitary treatment to ensure microbiological safety and shelf-life extension of several types of food products including pre-cut vegetables and some sous-vide meals, chilled ready-prepared meals, chilled ready-to-eat meat products, food for immuno-compromised patients/populations, sterile meals, ready-to-eat-food of intermediate moisture content. This publication presents the research results reported at the final Research Co-ordination meeting on this CRP held in Saint Hyacinthe, Quebec, Canada, 10-14 July 2000

  19. Radiation processing for safe, shelf-stable and ready-to-eat food. Proceedings of a final research co-ordination meeting

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-01-01

    The increasingly busy lifestyles of populations in many countries have driven the demand for safe, convenient and ready-to-eat food. Traditional food processes such as drying, canning or refrigeration offer a partial solution to this demand as the sensory quality of such food may be significantly affected or the products may be contaminated by pathogenic bacteria during preparation. For developing countries, safe shelf-stable food without the need for refrigeration would offer advantages. In addition, the increasing number of immuno-compromised populations in many countries requires a new approach to food safety to meet their needs. Irradiation offers a potential to enhance microbiological safety and quality of food through shelf-life extension. The benefits of irradiation as a sanitary treatment of many types of food are well known, some of which are applied commercially in several countries. Little data were available, however, on the effect of irradiation on minimally processed food and composite food including prepared meals. A Co-ordinated Research Project (CRP) on the Development of Safe, Shelf-Stable and Ready-to-Eat Food through Radiation Processing therefore was implemented by the Joint FAO/IAEA Division of Nuclear Techniques in Food and Agriculture in 1996 to evaluate the role of irradiation for such food. The results were encouraging as irradiation offers promise as a sanitary treatment to ensure microbiological safety and shelf-life extension of several types of food products including pre-cut vegetables and some sous-vide meals, chilled ready-prepared meals, chilled ready-to-eat meat products, food for immuno-compromised patients/populations, sterile meals, ready-to-eat-food of intermediate moisture content. This publication presents the research results reported at the final Research Co-ordination meeting on this CRP held in Saint Hyacinthe, Quebec, Canada, 10-14 July 2000.

  20. Hydraulic retention time affects stable acetate production from tofu processing wastewater in extreme-thermophilic (70°C) mixed culture fermentation.

    Science.gov (United States)

    Chen, Yun; Zhang, Fang; Wang, Ting; Shen, Nan; Yu, Zhong-Wei; Zeng, Raymond J

    2016-09-01

    Acetate is an important industrial chemical and its production from wastes via mixed culture fermentation (MCF) is economic. In this work, the effect of hydraulic retention time (HRT) on acetate production from tofu processing wastewater (TPW) in extreme-thermophilic (70°C) MCF was first investigated. It was found that long HRT (>3days) could lead to less acetate production while stable acetate production was achieved at short HRT (3days) with the yield of 0.57g-COD/g-CODTPW. The microbial community analysis showed that hydrogenotrophic methanogens (mainly Methanothermobacter) occupied up to 90% of archaea at both HRTs of 3 and 5days. However, Coprothermobacter, the main acetate-degraders, decreased from 35.74% to 10.58% of bacteria when HRT decreased from 5 to 3days, supporting the aggravation of syntrophic acetate oxidation in long HRT. This work demonstrated that HRT was a crucial factor to maintain stable acetate production from TPW in extreme-thermophilic MCF. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. 400 years of summer climatic conditions in the N Carpathian Mts. (eastern Europe) based on O and C stable isotopes in Pinus Cembra L tree rings

    Science.gov (United States)

    Nagavciuc, Viorica; Popa, Ionel; Kern, Zoltán; Persoiu, Aurel

    2016-04-01

    For a better understanding of how the climate is changing and how the environment responds to these changes, it is necessary to understand how the climate has varied in the past. Romania's virgin forests have a great potential to obtain long tree-ring chronologies with annual resolution; but so far, only a few studies resulted in quantitative paleoclimatic reconstructions. In this context, the aim of this study is 1) to calibrate the relationship between the stable isotopes of oxygen and carbon in tree rings and the main climatic parameters and determine the potential of Pinus cembra (Cǎlimani Mts., N Romania, Eastern Europe) for paleoclimatic reconstructions; 2) to provide the first palaeoclimatic reconstitution in Romania based on the isotopic composition of oxygen and carbon in tree ring cellulose, and 3) to test the hypothesis that nearby sulphur mines have not altered the climatic signal recorded by the stable isotopic composition of tree rings, contrary to the similar signal recorded by TRW. For this study, we have analysed wood samples of Swiss stone pine (Pinus cembra L.) from living and dead trees from Cǎlimani Mts., NE Romania, aged between 1600 and 2012 AD. The isotopic composition of oxygen and carbon from the cellulose was analysed at the Institute for Geological and Geochemical Research, Budapest, Hungary, using a high-temperature pyrolysis system (Thermo Quest TC-EA) coupled to an isotope ratio mass spectrometer (Thermo Finningan Delta V) following a ring by ring (i.e., non-pooled) approach. The average level of δ18O and δ13C in cellulose for the period 1600-2012 was 28.83‰ and -22.63 ‰. The tree ring cellulose δ18O and δ13C values showed a strong positive correlation with maximum air temperature (r = 0.6 for δ18O and r = 0.5 for δ13C), mean temperature (r = 0.6 for δ18O and r = 0.45 for δ13C), and sunshine duration (r = 0.69 for δ18O) and negatively correlated with precipitation amount (r = -0.5 for δ18O and r = 0.3 for δ13C) and

  2. Influence of pulsed plasma streams processing on wear behavior of steels in different friction conditions

    International Nuclear Information System (INIS)

    Bandura, A.N.; Byrka, O.V.; Tereshin, V.I.; Bovda, A.M.; Tortika, A.S.

    2000-01-01

    Pulsed plasma streams processing was applied for surface modification of industrial steel samples. Different types of wear tests (pin-on-disk,flat-on-flat, abrasive,cavitation) were carried out for samples irradiated by pulsed nitrogen plasma streams. There was achieved essential decrease of wear and tear of processed surfaces of all kinds of steels including previously thermally quenched ones. Obtained results are of importance for both determination of optimal regimes of plasma streams processing and the most resulting use of pulsed plasma streams for technology purpose, i.e. for identification of wear modes and optimal friction conditions for steels processed by plasma streams

  3. Part of the job: the role of physical work conditions in the nurse turnover process.

    Science.gov (United States)

    Vardaman, James M; Cornell, Paul T; Allen, David G; Gondo, Maria B; Muslin, Ivan S; Mobley, Robin N; Brock, Meagan E; Sigmon, Tracy L

    2014-01-01

    Retention of nursing staff remains an important issue for health care managers. Turnover research has focused primarily on motivational and social factors as keys to retention, whereas the role of the physical work conditions has received considerably less attention. However, work design theory suggests that physical work conditions may be an important factor in fostering retention among nursing staff. The aim of this study was to integrate work design theory with turnover process models to explore the influence of perceptions of physical work conditions on the development of turnover intentions among nursing staff. Drawing on two samples of registered nurses working in cancer units in metropolitan hospitals in the southeastern United States, this study explores the impact of perceptions of physical work conditions on turnover intentions using ordinary least squares regression. Hypotheses are tested in Study 1 and replicated in Study 2. A measure of perceptions of physical work conditions is also developed and validated using exploratory (Study 1) and confirmatory (Study 2) factor analyses. Perceptions of physical work conditions explain variance in turnover intentions above than that explained by motivational and social factors. Specifically, employee perceptions of noisy work conditions are found to significantly increase turnover intentions, whereas perceptions that work conditions facilitate tasks were found to significantly reduce turnover intentions. Perceptions of temperature and health hazard did not show significant effects. Results suggest that health care managers and scholars should re-examine the role of physical work conditions in the turnover process. Investments in upgrades that facilitate tasks may foster retention better than investments that simply improve employee comfort. Negative perceptions of work conditions may have no impact if they are considered a normal "part of the job," although negative perceptions of conditions that are viewed as

  4. Stable limits for sums of dependent infinite variance random variables

    DEFF Research Database (Denmark)

    Bartkiewicz, Katarzyna; Jakubowski, Adam; Mikosch, Thomas

    2011-01-01

    The aim of this paper is to provide conditions which ensure that the affinely transformed partial sums of a strictly stationary process converge in distribution to an infinite variance stable distribution. Conditions for this convergence to hold are known in the literature. However, most of these...

  5. Interfacial engineering of solution-processed Ni nanochain-SiO{sub x} (x < 2) cermets towards thermodynamically stable, anti-oxidation solar selective absorbers

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Xiaobai; Wang, Xiaoxin; Liu, Jifeng, E-mail: Jifeng.Liu@dartmouth.edu [Thayer School of Engineering, Dartmouth College, 14 Engineering Drive, Hanover, New Hampshire 03755 (United States); Zhang, Qinglin [Department of Chemical and Materials Engineering, University of Kentucky, 177 F. Paul Anderson Tower, Lexington, Kentucky 40506 (United States)

    2016-04-07

    Cermet solar thermal selective absorber coatings are an important component of high-efficiency concentrated solar power (CSP) receivers. The oxidation of the metal nanoparticles in cermet solar absorbers is a great challenge for vacuum-free operation. Recently, we have demonstrated that oxidation is kinetically retarded in solution processed, high-optical-performance Ni nanochain-SiO{sub x} cermet system compared to conventional Ni-Al{sub 2}O{sub 3} system when annealed in air at 450–600 °C for several hours. However, for long-term, high-temperature applications in CSP systems, thermodynamically stable antioxidation behavior is highly desirable, which requires new mechanisms beyond kinetically reducing the oxidation rate. Towards this goal, in this paper, we demonstrate that pre-operation annealing of Ni nanochain-SiO{sub x} cermets at 900 °C in N{sub 2} forms the thermodynamically stable orthorhombic phase of NiSi at the Ni/SiO{sub x} interfaces, leading to self-terminated oxidation at 550 °C in air due to this interfacial engineering. In contrast, pre-operation annealing at a lower temperature of 750 °C in N{sub 2} (as conducted in our previous work) cannot achieve interfacial NiSi formation directly, and further annealing in air at 450–600 °C for >4 h only leads to the formation of the less stable (metastable) hexagonal phase of NiSi. Therefore, the high-temperature pre-operation annealing is critical to form the desirable orthorhombic phase of NiSi at Ni/SiO{sub x} interfaces towards thermodynamically stable antioxidation behavior. Remarkably, with this improved interfacial engineering, the oxidation of 80-nm-diameter Ni nanochain-SiO{sub x} saturates after annealing at 550 °C in air for 12 h. Additional annealing at 550 °C in air for as long as 20 h (i.e., 32 h air annealing at >550 °C in total) has almost no further impact on the structural or optical properties of the coatings, the latter being very sensitive to any

  6. On-line Cutting Tool Condition Monitoring in Machining Processes Using Artificial Intelligence

    OpenAIRE

    Vallejo, Antonio J.; Morales-Menéndez, Rub&#;n; Alique, J.R.

    2008-01-01

    This chapter presented new ideas for monitoring and diagnosis of the cutting tool condition with two different algorithms for pattern recognition: HMM, and ANN. The monitoring and diagnosis system was implemented for peripheral milling process in HSM, where several Aluminium alloys and cutting tools were used. The flank wear (VB) was selected as the criterion to evaluate the tool's life and four cutting tool conditions were defined to be recognized: New, half new, half worn, and worn conditio...

  7. Effect of pretreatments and processing conditions on anti-nutritional factors in climbing bean flours

    Directory of Open Access Journals (Sweden)

    Emmanuel Mugabo

    2017-04-01

    Full Text Available It is difficult for many Rwandans to utilize climbing bean seeds (Phaseolus vulgaris. L mainly because of longer cooking time (2 hours and the high consumption of basic fuel. Climbing beans also contain anti-nutritional factors such tannins, phytates, trypsin inhibitors and phytohemagglutinins that limit nutrient absorption. One way to solve this problem is to utilize the flour of climbing beans made from different treatments and processing methods. In this study, climbing beans were pre-treated by soaking them in water for 24 hours, soaking in 2% sodium bicarbonate solution and steam blanching for 10 minutes. After that, pre-treated climbing beans were processed into flours by processing methods such as roasting, cooking and germination where anti-nutritional factors were reduced. The pretreatments did not significantly (p>0.05 affect phytates in climbing bean flours but processing conditions significantly (p<0.05 reduced it. Pretreatments and processing conditions significantly (p<0.05 reduced tannin content. The pretreatments followed by different processing conditions significantly (p<0.05 decreased trypsin inhibitors content. The great significant decrease in phytohemagglutinins content was observed in pretreatment followed by different processing methods. All pretreatments and processing conditions effectively decreased anti-nutritional factors at low level. However, pretreatments or untreated followed by germination and roasting were found to be the most and the least effective respectively.  Making flour from germinated climbing bean seeds is a good option for sustainable food processing as it reduces anti-nutritional factors. It is an inexpensive method in terms of time, energy and fuel for Rwandan households, restaurants and industries where climbing bean seeds are integral part of daily meal.

  8. Influence of Processing Conditions on the Mechanical Behavior of MWCNT Reinforced Thermoplastic Nanocomposites

    DEFF Research Database (Denmark)

    Doagou Rad, Saeed; Islam, Aminul; Jensen, Jakob Søndergaard

    2017-01-01

    The influence of the processing conditions and MWCNT content on the mechanical properties of PA6,6-based nanocomposites areinvestigated. In addition to the composition of the composites, the impact of manufacturing conditions such as dilution mechanism, twin-screwextruder mixing specifications......, and injection molding parameters on the behavior of the nanocomposites are evaluated. Results show that whilethe increase in the content of MWCNTs can lead to 40.0 % enhancement in the mechanical properties, changing the processing parametersvaries the values by 30.0 % in the same content. The mechanisms...... involved in the modulation of the nanocomposites properties are alsodiscussed...

  9. Intrinsic colony conditions affect the provisioning and oviposition process in the stingless bee Melipona scutellaris.

    Science.gov (United States)

    Pereira, R A; Morais, M M; Nascimento, F S; Bego, L R

    2009-01-01

    The cell provisioning and oviposition process (POP) is a unique characteristic of stingless bees (Meliponini), in which coordinated interactions between workers and queen regulate the filling of brood cells with larval resources and subsequent egg laying. Environmental conditions seem to regulate reproduction in stingless bees; however, little is known about how the amount of food affects quantitative sequences of the process. We examined intrinsic variables by comparing three colonies in distinct conditions (strong, intermediate and weak state). We predicted that some of these variables are correlated with temporal events of POP in Melipona scutellaris colonies. The results demonstrated that the strong colony had shorter periods of POP.

  10. Enhanced performance of denitrifying sulfide removal process under micro-aerobic condition.

    Science.gov (United States)

    Chen, Chuan; Ren, Nanqi; Wang, Aijie; Liu, Lihong; Lee, Duu-Jong

    2010-07-15

    The denitrifying sulfide removal (DSR) process with bio-granules comprising both heterotrophic and autotrophic denitrifiers can simultaneously convert nitrate, sulfide and acetate into di-nitrogen gas, elementary sulfur and carbon dioxide, respectively, at high loading rates. This study determines the reaction rate of sulfide oxidized into sulfur, as well as the reduction of nitrate to nitrite, would be enhanced under a micro-aerobic condition. The presence of limited oxygen mitigated the inhibition effects of sulfide on denitrifier activities, and enhanced the performance of DSR granules. The advantages and disadvantages of applying the micro-aerobic condition to the DSR process are discussed. 2010 Elsevier B.V. All rights reserved.

  11. Enhanced performance of denitrifying sulfide removal process under micro-aerobic condition

    International Nuclear Information System (INIS)

    Chen Chuan; Ren Nanqi; Wang Aijie; Liu Lihong; Lee, Duu-Jong

    2010-01-01

    The denitrifying sulfide removal (DSR) process with bio-granules comprising both heterotrophic and autotrophic denitrifiers can simultaneously convert nitrate, sulfide and acetate into di-nitrogen gas, elementary sulfur and carbon dioxide, respectively, at high loading rates. This study determines the reaction rate of sulfide oxidized into sulfur, as well as the reduction of nitrate to nitrite, would be enhanced under a micro-aerobic condition. The presence of limited oxygen mitigated the inhibition effects of sulfide on denitrifier activities, and enhanced the performance of DSR granules. The advantages and disadvantages of applying the micro-aerobic condition to the DSR process are discussed.

  12. Modeling the Process of Event Sequence Data Generated for Working Condition Diagnosis

    Directory of Open Access Journals (Sweden)

    Jianwei Ding

    2015-01-01

    Full Text Available Condition monitoring systems are widely used to monitor the working condition of equipment, generating a vast amount and variety of telemetry data in the process. The main task of surveillance focuses on analyzing these routinely collected telemetry data to help analyze the working condition in the equipment. However, with the rapid increase in the volume of telemetry data, it is a nontrivial task to analyze all the telemetry data to understand the working condition of the equipment without any a priori knowledge. In this paper, we proposed a probabilistic generative model called working condition model (WCM, which is capable of simulating the process of event sequence data generated and depicting the working condition of equipment at runtime. With the help of WCM, we are able to analyze how the event sequence data behave in different working modes and meanwhile to detect the working mode of an event sequence (working condition diagnosis. Furthermore, we have applied WCM to illustrative applications like automated detection of an anomalous event sequence for the runtime of equipment. Our experimental results on the real data sets demonstrate the effectiveness of the model.

  13. Intensive heat method for using non-segregate fine tailings for generating hot process water and stable solids that can support traffic

    Energy Technology Data Exchange (ETDEWEB)

    Betzer-Zilevitch, M. [Ex-Tar Technologies Inc., AB (Canada)

    2010-07-01

    This power point presentation described a method developed to extract energy from non-segregated fine tailings for generating hot process water. The method produced stable solids that were able to support traffic. Discharged non-segregated tailings passed through a zero liquid discharge direct contact steam generator (DCSG) and were then further treated and returned to the oil sands mine and bitumen extraction facility. A direct contact heat exchanger and condenser removed contaminates. Laboratory analyses confirmed that the DCSG condensate was toxic. Light organics were not destroyed. The method was then simulated in order to investigate the impact of pressure on performance. The study demonstrated that the method is both simple and robust. Non-segregated asphaltene-rich fine tailing streams can be used, and no changes to extraction, oil separation, or froth treatment equipment is needed. A cost benefit analysis was included. tabs., figs.

  14. Intensity effects in the formation of stable islands in phase space during the multi-turn extraction process at the CERN PS

    CERN Document Server

    Machida, Shinji; Prior, Chris; Gilardoni, Simone; Giovannozzi, Massimo; Hirlander, Simon; Huschauer, Alexander

    2016-01-01

    The CERN PS utilises a Multi-Turn Extraction (MTE) scheme to stretch the beam pulse length to optimise the filling process of the SPS. MTE is a novel technique to split a beam in transverse phase space into nonlinear stable islands. The recent experimental results indicate that the positions of the islands depend on the total beam intensity. Particle simulations have been performed to understand the detailed mechanism of the intensity dependence. The analysis carried out so far suggests space charge effects through image charges and image currents on the vacuum chamber and the magnets iron cores dominate the observed behaviour. In this talk, the latest analysis with realistic modelling of the beam environment is discussed and it is shown how this further improves the understanding of intensity effects in MTE.

  15. Integration of an optical coherence tomography (OCT) system into an examination incubator to facilitate in vivo imaging of cardiovascular development in higher vertebrate embryos under stable physiological conditions

    DEFF Research Database (Denmark)

    Happel, Christoph M.; Thrane, Lars; Thommes, Jan

    2011-01-01

    High-resolution in vivo imaging of higher vertebrate embryos over short or long time periods under constant physiological conditions is a technically challenging task for researchers working on cardiovascular development. In chick embryos, for example, various studies have shown that without...... significance, should be documented under physiological conditions. However, previous studies were mostly carried out outside of an incubator or under suboptimal environmental conditions. Here we present, to the best of our knowledge, the first detailed description of an optical coherence tomography (OCT......) system integrated into an examination incubator to facilitate real-time in vivo imaging of cardiovascular development under physiological environmental conditions. We demonstrate the suitability of this OCT examination incubator unit for use in cardiovascular development studies by examples of proof...

  16. Development of diagnostic process for abnormal conditions of Ulchin units 1 and 2

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Hyun Soo; Kwak, Jeong Keun; Yun, Jung Hyun; Kim, Jong Hyun [KEPCO International Nuclear Graduate School, Ulsan (Korea, Republic of)

    2012-10-15

    Diagnosis of abnormal conditions during operation is one of difficult tasks to nuclear power plant operators. Operators may have trouble in handling abnormal conditions due to various reasons such as 1) many alarms (around 2,000 alarms in the Ulchin units 1 and 2 each) and multi alarms occurrences, 2) the same alarms occurrences in different abnormal conditions, and 3) a number of Abnormal Operating Procedures (AOPs). For these reasons, the first diagnosis on abnormal conditions largely relies on operator's experiences and pattern recognition. Then, this difficulty may be highlighted for inexperienced operators. This paper suggests an approach to develop the optimal diagnostic process for appropriate selection of AOPs by using the Elimination by Aspect (EBA) method. The EBA method uses a heuristic followed by decision makers during a process of sequential choice and which constitutes a good balance between the cost of a decision and its quality. At each stage of decision, the individuals eliminate all the options not having an expected given attribute, until only one option remains. This approach is applied to steam generator level control system abnormal procedure for Ulchin units 1 and 2. The result indicates that the EBA method is applicable to the development of optimal process on diagnosis of abnormal conditions.

  17. Air Conditioning Compressor Air Leak Detection by Image Processing Techniques for Industrial Applications

    Directory of Open Access Journals (Sweden)

    Pookongchai Kritsada

    2015-01-01

    Full Text Available This paper presents method to detect air leakage of an air conditioning compressor using image processing techniques. Quality of air conditioning compressor should not have air leakage. To test an air conditioning compressor leak, air is pumped into a compressor and then submerged into the water tank. If air bubble occurs at surface of the air conditioning compressor, that leakage compressor must be returned for maintenance. In this work a new method to detect leakage and search leakage point with high accuracy, fast, and precise processes was proposed. In a preprocessing procedure to detect the air bubbles, threshold and median filter techniques have been used. Connected component labeling technique is used to detect the air bubbles while blob analysis is searching technique to analyze group of the air bubbles in sequential images. The experiments are tested with proposed algorithm to determine the leakage point of an air conditioning compressor. The location of the leakage point was presented as coordinated point. The results demonstrated that leakage point during process could be accurately detected. The estimation point had error less than 5% compared to the real leakage point.

  18. The Orexin Component of Fasting Triggers Memory Processes Underlying Conditioned Food Selection in the Rat

    Science.gov (United States)

    Ferry, Barbara; Duchamp-Viret, Patricia

    2014-01-01

    To test the selectivity of the orexin A (OXA) system in olfactory sensitivity, the present study compared the effects of fasting and of central infusion of OXA on the memory processes underlying odor-malaise association during the conditioned odor aversion (COA) paradigm. Animals implanted with a cannula in the left ventricle received ICV infusion…

  19. A cyano-terminated dithienyldiketopyrrolopyrrole dimer as a solution processable ambipolar semiconductor under ambient conditions.

    Science.gov (United States)

    Wang, Li; Zhang, Xiaojie; Tian, Hongkun; Lu, Yunfeng; Geng, Yanhou; Wang, Fosong

    2013-12-14

    A cyano-terminated dimer of dithienyldiketopyrrolopyrrole (TDPP), DPP2-CN, is a solution processable ambipolar semiconductor with field-effect hole and electron mobilities of 0.066 and 0.033 cm(2) V(-1) s(-1), respectively, under ambient conditions.

  20. Statistical Analysis of Deep Drilling Process Conditions Using Vibrations and Force Signals

    Directory of Open Access Journals (Sweden)

    Syafiq Hazwan

    2016-01-01

    Full Text Available Cooling systems is a key point for hot forming process of Ultra High Strength Steels (UHSS. Normally, cooling systems is made using deep drilling technique. Although deep twist drill is better than other drilling techniques in term of higher productivity however its main problem is premature tool breakage, which affects the production quality. In this paper, analysis of deep twist drill process parameters such as cutting speed, feed rate and depth of cut by using statistical analysis to identify the tool condition is presented. The comparisons between different two tool geometries are also studied. Measured data from vibrations and force sensors are being analyzed through several statistical parameters such as root mean square (RMS, mean, kurtosis, standard deviation and skewness. Result found that kurtosis and skewness value are the most appropriate parameters to represent the deep twist drill tool conditions behaviors from vibrations and forces data. The condition of the deep twist drill process been classified according to good, blunt and fracture. It also found that the different tool geometry parameters affect the performance of the tool drill. It believe the results of this study are useful in determining the suitable analysis method to be used for developing online tool condition monitoring system to identify the tertiary tool life stage and helps to avoid mature of tool fracture during drilling process.

  1. Acoustic Signal Processing for Pipe Condition Assessment (WaterRF Report 4360)

    Science.gov (United States)

    Unique to prestressed concrete cylinder pipe (PCCP), individual wire breaks create an excitation in the pipe wall that may vary in response to the remaining compression of the pipe core. This project was designed to improve acoustic signal processing for pipe condition assessment...

  2. Knowledge lost in data : Organizational impediments to condition-based maintenance in the process industry

    NARCIS (Netherlands)

    van de Kerkhof, Roland; Akkermans, Henk; Noorderhaven, Niels; Zijm, H.; Klumpp, M.; Clausen, U.; Ten Hompel, M.

    2016-01-01

    In this chapter we report on a pilot study of Condition-Based Maintenance (CBM) in the process industries, such as the steelmaking- and chemical industries, and propose a diagnostic instrument for systematically analysing the challenges to the successful implementation and execution of a CBM

  3. Working conditions and effects of ISO 9000 in six furniture-making companies: implementation and processes.

    Science.gov (United States)

    Karltun, J; Axelsson, J; Eklund, J

    1998-08-01

    What effects will the implementation of the quality standard ISO 9000 have regarding working conditions and competitive advantages? Which are the most important change process characteristics for assuring improved working conditions and other desired effects? These are the main questions behind this study of six furniture-making companies which implemented ISO 9000 during the period 1991-1994. The results show that customer requirement was the dominant goal to implement ISO 9000. Five of the six companies succeeded in gaining certification. The influence on working conditions was limited, but included better order and housekeeping, more positive attitudes towards discussing quality shortcomings, a few workplace improvements, work enrichment caused by additional tasks within the quality system and a better understanding of external customer demands. Among the negative effects were new, apparently meaningless, tasks for individual workers as well as more stress and more physically strenuous work. The effects on the companies included a decrease in external quality-related costs and improved delivery precision. The study confirms the importance for efficient change of the design of the change process, and identifies 'improvement methodology' as the most important process characteristic. Improved working conditions are enhanced by added relevant strategic goals and by a participative implementation process.

  4. Effects of hydrologic conditions on biogeochemical processes and organic pollutant degradation in salt marsh sediments

    Science.gov (United States)

    W. James Catallo

    2000-01-01

    This work addressed the influence of tidal vs. static hydrologic conditions on biogeochemical processes and the transformation of pollutant organic chemicals (eight representative N-, O-, and S-heterocycles (NOSHs) from coal chemicals, crude oils, and pyrogenic mixtures) in salt marsh sediments. The goals were to: (1) determine the effects of static (flooded, drained)...

  5. Nuclear structure and weak rates of heavy waiting point nuclei under rp-process conditions

    Science.gov (United States)

    Nabi, Jameel-Un; Böyükata, Mahmut

    2017-01-01

    The structure and the weak interaction mediated rates of the heavy waiting point (WP) nuclei 80Zr, 84Mo, 88Ru, 92Pd and 96Cd along N = Z line were studied within the interacting boson model-1 (IBM-1) and the proton-neutron quasi-particle random phase approximation (pn-QRPA). The energy levels of the N = Z WP nuclei were calculated by fitting the essential parameters of IBM-1 Hamiltonian and their geometric shapes were predicted by plotting potential energy surfaces (PESs). Half-lives, continuum electron capture rates, positron decay rates, electron capture cross sections of WP nuclei, energy rates of β-delayed protons and their emission probabilities were later calculated using the pn-QRPA. The calculated Gamow-Teller strength distributions were compared with previous calculation. We present positron decay and continuum electron capture rates on these WP nuclei under rp-process conditions using the same model. For the rp-process conditions, the calculated total weak rates are twice the Skyrme HF+BCS+QRPA rates for 80Zr. For remaining nuclei the two calculations compare well. The electron capture rates are significant and compete well with the corresponding positron decay rates under rp-process conditions. The finding of the present study supports that electron capture rates form an integral part of the weak rates under rp-process conditions and has an important role for the nuclear model calculations.

  6. Thermal processing of conditioned waste and fuel substitutes; Thermische Behandlung vorbehandelter Abfaelle und Ersatzbrennstoffe

    Energy Technology Data Exchange (ETDEWEB)

    Velden, F. van der; Engweiler, J. [Von Roll Umwelttechnik AG, Zurich (Switzerland)

    1998-12-31

    Different technologies for the thermal processing of mechanical-biologically conditioned waste are described and compared in terms of cost and flexibility. (orig.) [Deutsch] Es werden verschiedene Technologien der thermischen Behandlung mechanisch-biologisch vorbehandelter Abfaelle vorgestellt und im Hinblick auf Kosten und Flexibilitaet verglichen. (orig.)

  7. The improving of the heat networks operating process under the conditions of the energy efficiency providing

    Directory of Open Access Journals (Sweden)

    Blinova Tatiana

    2016-01-01

    Full Text Available Among the priorities it is important to highlight the modernization and improvement of energy efficiency of housing and communal services, as well as the transition to the principle of using the most efficient technologies used in reproduction (construction, creation of objects of municipal infrastructure and housing modernization. The main hypothesis of this study lies in the fact that in modern conditions the realization of the most important priorities of the state policy in the sphere of housing and communal services, is possible in the conditions of use of the most effective control technologies for the reproduction of thermal networks. It is possible to raise the level of information security Heat Distribution Company, and other market participants by improving business processes through the development of organizational and economic mechanism in the conditions of complex monitoring of heat network operation processes

  8. Influence of high gravity process conditions on the environmental impact of ethanol production from wheat straw

    DEFF Research Database (Denmark)

    Janssen, Matty; Tillman, Anne-Marie; Cannella, David

    2014-01-01

    Biofuel production processes at high gravity are currently under development. Most of these processes however use sugars or first generation feedstocks as substrate. This paper presents the results of a life cycle assessment (LCA) of the production of bio-ethanol at high gravity conditions from...... of the ethanol production, but this can be compensated by reducing the impact of enzyme production and use, and by polyethylene glycol addition at high dry matter content. The results also show that the renewable and non-renewable energy use resulting from the different process configurations ultimately...

  9. Computational science simulation of laser materials processing and provision of their irradiation conditions

    International Nuclear Information System (INIS)

    Muramatsu, Toshiharu

    2016-01-01

    In laser processing, it is necessary for achieving the intended performance and product, to understand the complex physical courses including melting and solidification phenomena occurring in laser processing, and thus to set proper laser irradiation conditions. This condition optimization work requires an enormous amount of overhead due to repeated efforts, and has become a cause for inhibiting the introduction of laser processing technology into the industrial field that points to the small lot production of many products. JAEA tried to make it possible to quantitatively handle the complex physical course from the laser light irradiation to the fabricating material until the completion of processing, and is under development of the computational science simulation code SPLICE that connects micro behavior and macro behavior through a multi-level scale model. This SPLICE is able to visualize the design space and to reduce the overhead associated with the setting of laser irradiation conditions and the like, which gives the prospect of being effective as a tool for front-loading. This approach has been confirmed to be effective for the welding and fusing process. (A.O.)

  10. Optimization of the thermal conditions for processing hatchery waste eggs as meal for feed.

    Science.gov (United States)

    Chiu, W Z; Wei, H W

    2011-05-01

    The purpose of this study was to optimize the thermal conditions for processing hatchery waste eggs (HWE) into rich feedstuff with lower electricity consumption by using response surface methodology. In the study, the effects of processing temperature and time on HWE meal (HWEM) quality and production were evaluated. As the results indicate, optimization was obtained when the processing lasted for 23 h at the fixed temperature of 65°C, resulting in higher protein digestibility in vitro (89.6%) and DM (88.5%) content of HWEM with lower electricity consumption (82.4 kWh/60 kg of HWE). No significant differences existed between the quality values predicted by mathematical formulae and those obtained through practical analyses in DM (87 vs. 88.5%), CP (39.2 vs. 38.3%), protein digestibility in vitro (90.7 vs. 89.6%), and electricity consumed (80.8 vs. 82.4 kWh/60 kg of HWE). Furthermore, the product derived from the optimized processing conditions had better biosecurity; Salmonella spp. were not found and Escherichia coli levels were substantially reduced (from 10(7) to 10(4) cfu/g). In summary, HWEM of superior quality can be produced when the processing conditions optimized in the current research are utilized.

  11. Enzymatic Phorbol Esters Degradation using the Germinated Jatropha Curcas Seed Lipase as Biocatalyst: Optimization Process Conditions by Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    Avita Kusuma Wardhani

    2016-10-01

    Full Text Available Utilization of Jatropha curcas seed cake is limited by the presence of phorbol esters (PE, which are the main toxic compound and heat stable. The objective of this research was to optimize the reaction conditions of the enzymatic PE degradation of the defatted Jatropha curcas seed cake (DJSC using the acetone-dried lipase from the germinated Jatropha curcas seeds as a biocatalyst. Response Surface Methodology (RSM using three-factors-three-levels Box-Behnken design was used to evaluate the effects of the reaction time, the ratio of buffer volume to DJSC, and the ratio of enzyme to DJSC on PE degradation. The results showed that the optimum conditions of PE degradation were 29.33 h, 51.11 : 6 (mL/g, and 30.10 : 5 (U/g cake for the reaction time, the ratio of buffer volume to DJSC, and the ratio of enzyme to DJSC, respectively. The predicted degradation of PE was 98.96% and not significantly different with the validated data of PE degradation. PE content was 0.035 mg/g, in which it was lower than PE in non-toxic Jatropha seeds. The results indicated that enzymatic degradation of PE might be a promising method for degradation of PE.  Copyright © 2016 BCREC GROUP. All rights reserved Received: 22nd December 2015; Revised: 1st April 2016; Accepted: 14th April 2016 How to Cite: Wardhani, A.K., Hidayat, C., Hastuti, P. (2016. Enzymatic Phorbol Esters Degradation using the Germinated Jatropha Curcas Seed Lipase as Biocatalyst: Optimization Process Conditions by Response Surface Methodology. Bulletin of Chemical Reaction Engineering & Catalysis, 11 (3: 346-353 (doi:10.9767/bcrec.11.3.574.346-353 Permalink/DOI: http://doi.org/10.9767/bcrec.11.3.574.346-353

  12. Alternative assessment of nano-TiO{sub 2} sedimentation under different conditions based on sedimentation efficiency at quasi-stable state

    Energy Technology Data Exchange (ETDEWEB)

    He, Guang’an; Chen, Rui; Lu, Shushen [Sun Yat-sen University, School of Chemistry and Chemical Engineering (China); Jiang, Chengchun [Shenzhen Polytechnic, School of Civil and Environmental Engineering (China); Liu, Hong, E-mail: liuhong@cigit.ac.cn [Sun Yat-sen University, School of Chemistry and Chemical Engineering (China); Wang, Chuan [Chinese Academy of Sciences, Chongqing Institute of Green and Intelligent Technology (China)

    2015-11-15

    The predictable significant increase in manufacture and use of engineered nanoparticles (ENPs) will cause their inevitable release into environment, and the potential harmful effects of ENPs have been confirmed. As representative ENPs, sedimentation behavior of nano-titanium dioxide (n-TiO{sub 2}) should be better understood to control its environmental risk. In this study, an experimental methodology was established to set the sampling area and sampling time of n-TiO{sub 2} sedimentation. In addition, we defined a quasi-stable state and a precise index, i.e., sedimentation efficiency (SE) at this state, to describe the n-TiO{sub 2} sedimentation behavior. Both alternative concentration determination and conventional size measurement were applied to evaluate the sedimentation behavior of n-TiO{sub 2} with fulvic acid. Results showed that the sedimentation behavior described by SE was more precise and in disagreement with those predicted by particle size. Moreover, sedimentation experiments with salicylic acid (SA), under an electric field and different water temperatures or with sulfosalicylic acid under light irradiation were also performed. When the total organic carbon concentration of SA, the voltage of working electrodes, and water temperature increased, or the wavelength of light source decreased, the SE of n-TiO{sub 2} increased and n-TiO{sub 2} showed a tendency to settle in water. These findings might be important for deepening the understanding of n-TiO{sub 2} environmental behavior and exploring sedimentation behavior of other ENPs.

  13. thermo-stable alpha-amylase(S) from irradiated microbial origin utilizing agricultural and environmental wastes under solid state fermentation conditions

    International Nuclear Information System (INIS)

    Moustafa, O.E.A.

    2002-01-01

    an investigation concerning the production of thermo-stable α-amylases by thermophilic bacterial and fungal isolates has been undertaken. nine thermophilic bacteria and five teen fungi were isolated from different localities viz. phyllosphere of water hyacinth, different desert plants leaves, fermented dough, oven dust, garbage , and soil. their amylolytic activities were tested by dinitrosalicylic acid color reagent (Dns) method when grown on some environmental pollutants (garbage and water hyacinth) as well as industrial wastes (Bagasse, biscuit, corn flex and dough residues ) as the sole carbon source at 65 o C for bacterial and at 50 o C for fungal isolates . isolates No. B 1 ,B 2 ,B 5 ,B 6 ,B 7 ,B 8 ,B 9 , and F 4 ,F 6 ,F 8 ,F 1 2,F 1 3 and F 1 5, exhibited the highest α -amylase production when grown on water hyacinth, while B 4 ,F 3 ,F 1 1 and F 1 3, on dough ; (B 3 ,F 9 and F 1 0 ) on bagasse and ( F 1 ,F 2 ,F 5 ,F 7 ,F 1 1 and F 1 4) on garbage. Out of the nine identified bacterial isolated, only two isolates viz; actinobacillus actinomycetemcomitans, B1 and strepto bacillus moniliformis, B 7 , exhibited the ability to produce high percentages of α amylases at 55 o C (while still able to produce the enzyme within 45-70 o C)

  14. Adding complex terrain and stable atmospheric condition capability to the OpenFOAM-based flow solver of the simulator for on/offshore wind farm applications (SOWFA

    Directory of Open Access Journals (Sweden)

    Churchfield Matthew J.

    2014-01-01

    Full Text Available The National Renewable Energy Laboratory's Simulator for On/Offshore Wind Farm Applications contains an OpenFOAM-based flow solver for performing large-eddy simulation of flow through wind plants. The solver computes the atmospheric boundary layer flow and models turbines with actuator lines. Until recently, the solver was limited to flows over flat terrain and could only use the standard Smagorinsky subgrid-scale model. In this work, we present our improvements to the flow solver that enable us to 1 use any OpenFOAM-standard subgrid-scale model and 2 simulate flow over complex terrain. We used the flow solver to compute a stably stratified atmospheric boundary layer using both the standard and the Lagrangian-averaged scale-independent dynamic Smagorinsky models. Surprisingly, the results using the standard Smagorinsky model compare well to other researchers' results of the same case, although it is often said that the standard Smagorinsky model is too dissipative for accurate stable stratification calculations. The scale-independent dynamic subgrid-scale model produced poor results, probably due to the spikes in model constant with values as high as 4.6. We applied a simple bounding of the model constant to remove these spikes, which caused the model to produce results much more in line with other researchers' results. We also computed flow over a simple hilly terrain and performed some basic qualitative analysis to verify the proper operation of the terrain-local surface stress model we employed.

  15. A protocol for pressurized liquid extraction and processing methods to isolate modern and ancient bone cholesterol for compound-specific stable isotope analysis.

    Science.gov (United States)

    Laffey, Ann O; Krigbaum, John; Zimmerman, Andrew R

    2017-02-15

    Bone lipid compound-specific isotope analysis (CSIA) and bone collagen and apatite stable isotope ratio analysis are important sources of ecological and paleodietary information. Pressurized liquid extraction (PLE) is quicker and utilizes less solvent than traditional methods of lipid extraction such as soxhlet and ultrasonication. This study facilitates dietary analysis by optimizing and testing a standardized methodology for PLE of bone cholesterol. Modern and archaeological bones were extracted by PLE using varied temperatures, solvent solutions, and sample weights. The efficiency of PLE was assessed via quantification of cholesterol yields. Stable isotopic ratio integrity was evaluated by comparing isotopic signatures (δ 13 C and δ 18 O values) of cholesterol derived from whole bone, bone collagen and bone apatite. Gas chromatography/mass spectrometry (GC/MS) and gas chromatography isotope ratio mass spectrometry (GC/IRMS) were conducted on purified collagen and lipid extracts to assess isotopic responses to PLE. Lipid yield was optimized at two PLE extraction cycles of 75 °C using dichloromethane/methanol (2:1 v/v) as a solvent with 0.25-0.75 g bone sample. Following lipid extraction, saponification combined with the derivatization of the neutral fraction using trimethylsilylation yielded nearly twice the cholesterol of non-saponified or non-derivatized samples. It was also found that lipids extracted from purified bone collagen and apatite could be used for cholesterol CSIA. There was no difference in the bulk δ 13 C values of collagen extracted from bone with or without lipid. However, there was a significant depletion in 18 O of bone apatite due to lipid presence or processing. These results should assist sample selection and provide an effective, alternative extraction method for bone cholesterol that may be used for isotopic and paleodietary analysis. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

  16. Process-conditioned bias correction for seasonal forecasting: a case-study with ENSO in Peru

    Science.gov (United States)

    Manzanas, R.; Gutiérrez, J. M.

    2018-05-01

    This work assesses the suitability of a first simple attempt for process-conditioned bias correction in the context of seasonal forecasting. To do this, we focus on the northwestern part of Peru and bias correct 1- and 4-month lead seasonal predictions of boreal winter (DJF) precipitation from the ECMWF System4 forecasting system for the period 1981-2010. In order to include information about the underlying large-scale circulation which may help to discriminate between precipitation affected by different processes, we introduce here an empirical quantile-quantile mapping method which runs conditioned on the state of the Southern Oscillation Index (SOI), which is accurately predicted by System4 and is known to affect the local climate. Beyond the reduction of model biases, our results show that the SOI-conditioned method yields better ROC skill scores and reliability than the raw model output over the entire region of study, whereas the standard unconditioned implementation provides no added value for any of these metrics. This suggests that conditioning the bias correction on simple but well-simulated large-scale processes relevant to the local climate may be a suitable approach for seasonal forecasting. Yet, further research on the suitability of the application of similar approaches to the one considered here for other regions, seasons and/or variables is needed.

  17. Implementation of decommissioning materials conditional clearance process to the OMEGA calculation code

    International Nuclear Information System (INIS)

    Zachar, Matej; Necas, Vladimir; Daniska, Vladimir

    2011-01-01

    The activities performed during nuclear installation decommissioning process inevitably lead to the production of large amount of radioactive material to be managed. Significant part of materials has such low radioactivity level that allows them to be released to the environment without any restriction for further use. On the other hand, for materials with radioactivity slightly above the defined unconditional clearance level, there is a possibility to release them conditionally for a specific purpose in accordance with developed scenario assuring that radiation exposure limits for population not to be exceeded. The procedure of managing such decommissioning materials, mentioned above, could lead to recycling and reuse of more solid materials and to save the radioactive waste repository volume. In the paper an a implementation of the process of conditional release to the OMEGA Code is analyzed in details; the Code is used for calculation of decommissioning parameters. The analytical approach in the material parameters assessment, firstly, assumes a definition of radiological limit conditions, based on the evaluation of possible scenarios for conditionally released materials, and their application to appropriate sorter type in existing material and radioactivity flow system. Other calculation procedures with relevant technological or economical parameters, mathematically describing e.g. final radiation monitoring or transport outside the locality, are applied to the OMEGA Code in the next step. Together with limits, new procedures creating independent material stream allow evaluation of conditional material release process during decommissioning. Model calculations evaluating various scenarios with different input parameters and considering conditional release of materials to the environment are performed to verify the implemented methodology. Output parameters and results of the model assessment are presented, discussed and conduced in the final part of the paper

  18. Efficient and stable CH3NH3PbI3-x(SCN)x planar perovskite solar cells fabricated in ambient air with low-temperature process

    Science.gov (United States)

    Zhang, Zongbao; Zhou, Yang; Cai, Yangyang; Liu, Hui; Qin, Qiqi; Lu, Xubing; Gao, Xingsen; Shui, Lingling; Wu, Sujuan; Liu, Jun-Ming

    2018-02-01

    Planar perovskite solar cells (PSCs) based on CH3NH3PbI3-x(SCN)x (SCN: thiocyanate) active layer and low-temperature processed TiO2 films are fabricated by a sequential two-step method in ambient air. Here, alkali thiocyanates (NaSCN, KSCN) are added into Pb(SCN)2 precursor to improve the microstructure of CH3NH3PbI3-x(SCN)x perovskite layers and performance of the as-prepared PSCs. At the optimum concentrations of alkali thiocyanates as additives, the as-prepared NaSCN-modified and KSCN-modified PSCs demonstrate the efficiencies of 16.59% and 15.63% respectively, being much higher than 12.73% of the reference PSCs without additives. This improvement is primarily ascribed to the enhanced electron transport, reduced recombination rates and much improved microstructures with large grain size and low defect density at grain boundaries. Importantly, it is revealed that the modified PSCs at the optimized concentrations of alkali thiocyanates additives exhibit remarkably improved stability than the reference PSCs against humid circumstance, and a continuous exposure to humid air without encapsulation over 45 days only records about 5% degradation of the efficiency. These findings provide a facile approach to fabricate efficient and stable PSCs by low processing temperature in ambient air, both of which are highly preferred for future practical applications of PSCs.

  19. Rate-Independent Processes with Linear Growth Energies and Time-Dependent Boundary Conditions

    Czech Academy of Sciences Publication Activity Database

    Kružík, Martin; Zimmer, J.

    2012-01-01

    Roč. 5, č. 3 (2012), s. 591-604 ISSN 1937-1632 R&D Projects: GA AV ČR IAA100750802 Grant - others:GA ČR(CZ) GAP201/10/0357 Institutional research plan: CEZ:AV0Z10750506 Keywords : concentrations * oscillations * time - dependent boundary conditions * rate-independent evolution Subject RIV: BA - General Mathematics http://library.utia.cas.cz/separaty/2011/MTR/kruzik-rate-independent processes with linear growth energies and time - dependent boundary conditions.pdf

  20. Thermal processing of bone: in vitro response of mesenchymal cells to bone-conditioned medium.

    Science.gov (United States)

    Sawada, K; Caballé-Serrano, J; Schuldt Filho, G; Bosshardt, D D; Schaller, B; Buser, D; Gruber, R

    2015-08-01

    The autoclaving, pasteurization, and freezing of bone grafts to remove bacteria and viruses, and for preservation, respectively, is considered to alter biological properties during graft consolidation. Fresh bone grafts release paracrine-like signals that are considered to support tissue regeneration. However, the impact of the autoclaving, pasteurization, and freezing of bone grafts on paracrine signals remains unknown. Therefore, conditioned medium was prepared from porcine cortical bone chips that had undergone thermal processing. The biological properties of the bone-conditioned medium were assessed by examining the changes in expression of target genes in oral fibroblasts. The data showed that conditioned medium obtained from bone chips that had undergone pasteurization and freezing changed the expression of adrenomedullin, pentraxin 3, BTB/POZ domain-containing protein 11, interleukin 11, NADPH oxidase 4, and proteoglycan 4 by at least five-fold in oral fibroblasts. Bone-conditioned medium obtained from autoclaved bone chips, however, failed to change the expression of the respective genes. Also, when bone-conditioned medium was prepared from fresh bone chips, autoclaving blocked the capacity of bone-conditioned medium to modulate gene expression. These in vitro results suggest that pasteurization and freezing of bone grafts preserve the release of biologically active paracrine signals, but autoclaving does not. Copyright © 2015 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  1. Weak interaction rates for Kr and Sr waiting-point nuclei under rp-process conditions

    International Nuclear Information System (INIS)

    Sarriguren, P.

    2009-01-01

    Weak interaction rates are studied in neutron deficient Kr and Sr waiting-point isotopes in ranges of densities and temperatures relevant for the rp process. The nuclear structure is described within a microscopic model (deformed QRPA) that reproduces not only the half-lives but also the Gamow-Teller strength distributions recently measured. The various sensitivities of the decay rates to both density and temperature are discussed. Continuum electron capture is shown to contribute significantly to the weak rates at rp-process conditions.

  2. Mechanical Behaviour of Conventional Materials at Experimental Conditions of Deep Drawing Technological Process

    Science.gov (United States)

    Nikolov, N.; Pashkouleva, D.; Kavardzhikov, V.

    2012-09-01

    The paper deals with experimental investigations on the mechanical behaviour of body-centred-cubic (BCC) and face-centred-cubic (FCC)-conventionally structured sheet metalic-metalic materials under stress-strain conditions of a deep drawing process determined by a coefficient close to the limiting one for Steel 08 and punch diameter of 50 mm. The mechanical characteristics of the investigated materials are identified by one-dimensional tension tests. The materials' responses, as results of identical loading conditions, are described by the change of blank sizes and characteristics of the forming processes. The chosen deformation path ensures obtaining a qualitative steel piece and leads to failures of aluminium and brass blanks. The reported results could be useful for investigations and predictions of the mechanical responses of such type metallic structures applying microscopic instrumented observations and numerical simulations.

  3. Effect of processing conditions on the mechanical and thermal properties of high-impact polypropylene nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Furlan, L G [Federal Institute of Rio Grande do Sul, IFRS, Campus Restinga, Estrada Joao Antonio da Silveira, 351, Porto Alegre 91790-400 (Brazil); Ferreira, C I; Dal Castel, C; Santos, K S; Mello, A C.E. [Chemistry Institute, Federal University of Rio Grande do Sul, UFRGS, Av. Bento Goncalves, 9500, Porto Alegre 91501-970 (Brazil); Liberman, S A; Oviedo, M A.S. [Braskem S.A., III Polo Petroquimico, Via Oeste, Lote 5, Triunfo 95853-000 (Brazil); Mauler, R.S., E-mail: mauler@iq.ufrgs.br [Chemistry Institute, Federal University of Rio Grande do Sul, UFRGS, Av. Bento Goncalves, 9500, Porto Alegre 91501-970 (Brazil)

    2011-08-25

    Highlights: {yields} Polypropylene montmorillonite (PP-MMT) produced at different processing conditions. {yields} Polypropylene Nanocomposites with higher increase on impact resistance. {yields} Higher enhancement on mechanical properties. - Abstract: Polypropylene montmorillonite (PP-MMT) nanocomposites have been prepared by using a co-rotating twin screw extruder. The effects of processing conditions at fixed clay content (5 wt%) on polymer properties were investigated by means of transmission electron microscopy (TEM), flexural modulus, izod impact, dynamic mechanical analysis (DMA), and differential scanning calorimetry (DSC). It was noticed that the morphology and the mechanical properties of polypropylene nanocomposites were affected by different screw shear configuration. The results showed that the higher enhancement on mechanical properties was obtained by medium shear intensity profile instead of high configuration. An exceptional increase (maximum of 282%) on impact resistance was observed.

  4. Effect of processing conditions on the mechanical and thermal properties of high-impact polypropylene nanocomposites

    International Nuclear Information System (INIS)

    Furlan, L.G.; Ferreira, C.I.; Dal Castel, C.; Santos, K.S.; Mello, A.C.E.; Liberman, S.A.; Oviedo, M.A.S.; Mauler, R.S.

    2011-01-01

    Highlights: → Polypropylene montmorillonite (PP-MMT) produced at different processing conditions. → Polypropylene Nanocomposites with higher increase on impact resistance. → Higher enhancement on mechanical properties. - Abstract: Polypropylene montmorillonite (PP-MMT) nanocomposites have been prepared by using a co-rotating twin screw extruder. The effects of processing conditions at fixed clay content (5 wt%) on polymer properties were investigated by means of transmission electron microscopy (TEM), flexural modulus, izod impact, dynamic mechanical analysis (DMA), and differential scanning calorimetry (DSC). It was noticed that the morphology and the mechanical properties of polypropylene nanocomposites were affected by different screw shear configuration. The results showed that the higher enhancement on mechanical properties was obtained by medium shear intensity profile instead of high configuration. An exceptional increase (maximum of 282%) on impact resistance was observed.

  5. Organic priority substances and microbial processes in river sediments subject to contrasting hydrological conditions.

    Science.gov (United States)

    Zoppini, Annamaria; Ademollo, Nicoletta; Amalfitano, Stefano; Casella, Patrizia; Patrolecco, Luisa; Polesello, Stefano

    2014-06-15

    Flood and drought events of higher intensity and frequency are expected to increase in arid and semi-arid regions, in which temporary rivers represent both a water resource and an aquatic ecosystem to be preserved. In this study, we explored the variation of two classes of hazardous substances (Polycyclic Aromatic Hydrocarbons and Nonylphenols) and the functioning of the microbial community in river sediments subject to hydrological fluctuations (Candelaro river basin, Italy). Overall, the concentration of pollutants (∑PAHs range 8-275ngg(-1); ∑NPs range 299-4858ngg(-1)) suggests a moderate degree of contamination. The conditions in which the sediments were tested, flow (high/low) and no flow (wet/dry/arid), were associated to significant differences in the chemical and microbial properties. The total organic carbon contribution decreased together with the stream flow reduction, while the contribution of C-PAHs and C-NPs tended to increase. NPs were relatively more concentrated in sediments under high flow, while the more hydrophobic PAHs accumulated under low and no flow conditions. Passing from high to no flow conditions, a gradual reduction of microbial processes was observed, to reach the lowest specific bacterial carbon production rates (0.06fmolCh(-1)cell(-1)), extracellular enzyme activities, and the highest doubling time (40h) in arid sediments. In conclusion, different scenarios for the mobilization of pollutants and microbial processes can be identified under contrasting hydrological conditions: (i) the mobilization of pollutants under high flow and a relatively higher probability for biodegradation; (ii) the accumulation of pollutants during low flow and lower probability for biodegradation; (iii) the drastic reduction of pollutant concentrations under dry and arid conditions, probably independently from the microbial activity (abiotic processes). Our findings let us infer that a multiple approach has to be considered for an appropriate water

  6. Effects of microbial processes on gas generation under expected WIPP repository conditions: Annual report through 1992

    International Nuclear Information System (INIS)

    Francis, A.J.; Gillow, J.B.

    1993-09-01

    Microbial processes involved in gas generation from degradation of the organic constituents of transuranic waste under conditions expected at the Waste Isolation Pilot Plant (WIPP) repository are being investigated at Brookhaven National Laboratory. These laboratory studies are part of the Sandia National Laboratories -- WIPP Gas Generation Program. Gas generation due to microbial degradation of representative cellulosic waste was investigated in short-term ( 6 months) experiments by incubating representative paper (filter paper, paper towels, and tissue) in WIPP brine under initially aerobic (air) and anaerobic (nitrogen) conditions. Samples from the WIPP surficial environment and underground workings harbor gas-producing halophilic microorganisms, the activities of which were studied in short-term experiments. The microorganisms metabolized a variety of organic compounds including cellulose under aerobic, anaerobic, and denitrifying conditions. In long-term experiments, the effects of added nutrients (trace amounts of ammonium nitrate, phosphate, and yeast extract), no nutrients, and nutrients plus excess nitrate on gas production from cellulose degradation

  7. Conductivity enhancement of surface-polymerized polyaniline films via control of processing conditions

    Science.gov (United States)

    Park, Chung Hyoi; Jang, Sung Kyu; Kim, Felix Sunjoo

    2018-01-01

    We investigate a fast and facile approach for the simultaneous synthesis and coating of conducting polyaniline (PANI) onto a substrate and the effects of processing conditions on the electrical properties of the fabricated films. Simultaneous polymerizing and depositing on the substrate forms a thin film with the average thickness of 300 nm and sheet resistance of 304 Ω/sq. Deposition conditions such as polymerization time (3-240 min), temperature (-10 to 40 °C), concentrations of monomer and oxidant (0.1-0.9 M), and type of washing solvents (acetone, water, and/or HCl solution) affect the film thickness, doping state, absorption characteristics, and solid-state nanoscale morphology, therefore affecting the electrical conductivity. Among the conditions, the surface-polymerized PANI film deposited at room temperature with acetone washing showed the highest conductivity of 22.2 S/cm.

  8. Ocean circulation and shelf processes in the Arctic, Mediterranean traced by radiogenic neodymium isotopes, rare earth elements and stable oxygen isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Laukert, Georgi

    2017-02-20

    Disentangling the sources, distribution and mixing of water masses involved in the transport and transfer of heat and freshwater in the Arctic Mediterranean (i.e. the Arctic Ocean and the Nordic Seas, AM) is critical for the understanding of present and future hydrological changes in the high-latitude regions. This study refines the knowledge of water mass circulation in the AM and provides new insights into the processes occurring on the Arctic shelves and in high-latitude estuaries. A multi-proxy approach is used combining dissolved radiogenic Nd isotopes (ε{sub Nd}), rare earth elements (REEs) and stable oxygen isotopes (δ{sup 18}O) together with standard hydrographic tracers. The sources, distribution and mixing of water masses that circulate in the AM and pass the Fram Strait are assessed through evaluation of dissolved ε{sub Nd} and REE, and δ{sup 18}O data obtained from samples recovered in 2012, 2014 and 2015, and through a compilation and reassessment of literature Nd isotope and concentration data previously reported for other sites within the AM. The Nd isotope and REE distribution in the central Fram Strait and the open AM is shown to primarily reflect the lateral advection of water masses and their mixing, whereas seawater-particle interactions exert important control only above the shelf regions. New insights into the processes occurring in high latitude estuaries are provided by dissolved Nd isotope and REE compositions together with δ{sup 18}O data for the Laptev Sea based on filtered samples recovered in 2012, 2013 and 2014. A combination of REE removal through coagulation of nanoparticles and colloids and REE redistribution within the water column through formation and melting of sea ice and river ice is suggested to account for the distribution of all REEs, while no REE release from particles is observed. The ice-related processes contribute to the redistribution of other elements and ultimately may also affect primary productivity in high

  9. Low-temperature, solution-processed aluminum-doped zinc oxide as electron transport layer for stable efficient polymer solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Qianqian [College of Materials Science and Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao 266101 (China); Bao, Xichang, E-mail: baoxc@qibebt.ac.cn [Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao 266101 (China); Yu, Jianhua [College of Materials Science and Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Zhu, Dangqiang [Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao 266101 (China); Zhang, Qian [College of Materials Science and Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Gu, Chuantao [Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao 266101 (China); Dong, Hongzhou [College of Materials Science and Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Yang, Renqiang [Qingdao Institute of Bioenergy and Bioprocess Technology, Chinese Academy of Sciences, Qingdao 266101 (China); Dong, Lifeng, E-mail: DongLifeng@qust.edu.cn [College of Materials Science and Engineering, Qingdao University of Science and Technology, Qingdao 266042 (China); Department of Physics, Hamline University, St. Paul, MN 55104 (United States)

    2016-04-30

    A simple low-temperature solution-processed zinc oxide (ZnO) and aluminum-doped ZnO (AZO) were synthesized and investigated as an electron transport layer (ETL) for inverted polymer solar cells. A solar cell with a blend of poly(4,8-bis-alkyloxy-benzo[1,2-b:4,5-b′] dithiophene-alt-alkylcarbonyl-thieno [3,4-b] thiophene) and (6,6)-phenyl-C71-butyric acid methyl ester as an active layer and AZO as ETL demonstrates a high power conversion efficiency (PCE) of 7.36% under the illumination of AM 1.5G, 100 mW/cm{sup 2}. Compared to the cells with ZnO ETL (PCE of 6.85%), the PCE is improved by 7.45% with the introduction of an AZO layer. The improved PCE is ascribed to the enhanced short circuit current density, which results from the electron transport property of the AZO layer. Moreover, AZO is a more stable interfacial layer than ZnO. The PCE of the solar cells with AZO as ETL retain 85% of their original value after storage for 120 days, superior to the 39% of cells with ZnO ETL. The results above indicate that a simple low-temperature solution-processed AZO film is an efficient and economical ETL for high-performance inverted polymer solar cells. Due to its environmental friendliness, good electrical properties, and simple preparation approach, AZO has the potential to be applied in high-performance, large-scale industrialization of solar cells and other electronic devices. - Highlights: • ZnO and AZO were synthesized by a simple low-temperature solution-processed method. • AZO films show high transmittance and conductivity. • The photovoltaic performance can be improved with AZO as ETL. • AZO-based devices demonstrate excellent stability, with 85% retained after 120 days.

  10. A novel hyper-viscoelastic model for consolidation of toughened prepregs under processing conditions

    OpenAIRE

    Belnoue, J.P.-H.; Nixon-Pearson, O.J.; Ivanov, D.; Hallett, S.R.

    2016-01-01

    The paper presents a new modelling concept for describing the compressibility of toughened uncured prepregs over a wide range of processing conditions (i.e. automatic fibre deposition, hot debulking and pre-curing consolidation). The primary challenge of the work is to simulate the material response due complex flow and deformation mechanisms. This generation of prepreg systems exhibits both percolation (bleeding) flow typical for conventional thermosets, where the pressure gradient causes re...

  11. Conditions for the existence of quasi-stationary distributions for birth–death processes with killing

    OpenAIRE

    van Doorn, Erik A.

    2012-01-01

    We consider birth-death processes on the nonnegative integers, where $\\{1,2,...\\}$ is an irreducible class and $0$ an absorbing state, with the additional feature that a transition to state $0$ (killing) may occur from any state. Assuming that absorption at $0$ is certain we are interested in additional conditions on the transition rates for the existence of a quasi-stationary distribution. Inspired by results of M. Kolb and D. Steinsaltz (Quasilimiting behaviour for one-dimensional diffusion...

  12. Effect of stable and fluctuating temperatures on the life history traits of Anopheles arabiensis and An. quadriannulatus under conditions of inter- and intra-specific competition.

    Science.gov (United States)

    Davies, Craig; Coetzee, Maureen; Lyons, Candice L

    2016-06-14

    Constant and fluctuating temperatures influence important life-history parameters of malaria vectors which has implications for community organization and the malaria disease burden. The effects of environmental temperature on the hatch rate, survivorship and development rate of Anopheles arabiensis and An. quadriannulatus under conditions of inter- and intra-specific competition are studied. The eggs and larvae of laboratory established colonies were reared under controlled conditions at one constant (25 °C) and two fluctuating (20-30 °C and 18-35 °C) temperature treatments at a ratio of 1:0 or 1:1 (An. arabiensis: An. quadriannulatus). Monitoring of hatch rate, development rate and survival was done at three intervals, 6 to 8 h apart depending on developmental stage. Parametric ANOVAs were used where assumptions of equal variances and normality were met, and a Welch ANOVA where equal variance was violated (α = 0.05). Temperature significantly influenced the measured life-history traits and importantly, this was evident when these species co-occurred. A constant temperature resulted in a higher hatch rate in single species, larval treatments (P competitor (P < 0.05). The influence of temperature treatment on the development rate and survival from egg/larvae to adult differed across species treatments. Fluctuating temperatures incorporating the extremes influence the key life-history parameters measured here with An. arabiensis outcompeting An. quadriannulatus under these conditions. The quantification of the response variables measured here improve our knowledge of the link between temperature and species interactions and provide valuable information for modelling of vector population dynamics.

  13. Stable symbiotic nitrogen fixation under water-deficit field conditions by a stress-tolerant alfalfa microsymbiont and its complete genome sequence.

    Science.gov (United States)

    Jozefkowicz, Cintia; Brambilla, Silvina; Frare, Romina; Stritzler, Margarita; Piccinetti, Carlos; Puente, Mariana; Berini, Carolina Andrea; Pérez, Pedro Reyes; Soto, Gabriela; Ayub, Nicolás

    2017-12-10

    We here characterized the stress-tolerant alfalfa microsymbiont Sinorhizobium meliloti B401. B401-treated plants showed high nitrogen fixation rates under humid and semiarid environments. The production of glycine betaine in isolated bacteroids positively correlated with low precipitation levels, suggesting that this compound acts as a critical osmoprotectant under field conditions. Genome analysis revealed that strain B401 contains alternative pathways for the biosynthesis and uptake of glycine betaine and its precursors. Such genomic information will offer substantial insight into the environmental physiology of this biotechnologically valuable nitrogen-fixing bacterium. Copyright © 2017 Elsevier B.V. All rights reserved.

  14. Understanding Nutrient Processing Under Similar Hydrologic Conditions Along a River Continuum

    Science.gov (United States)

    Garayburu-Caruso, V. A.; Mortensen, J.; Van Horn, D. J.; Gonzalez-Pinzon, R.

    2015-12-01

    Eutrophication is one of the main causes of water impairment across the US. The fate of nutrients in streams is typically described by the dynamic coupling of physical processes and biochemical processes. However, isolating each of these processes and determining its contribution to the whole system is challenging due to the complexity of the physical, chemical and biological domains. We conducted column experiments seeking to understand nutrient processing in shallow sediment-water interactions along representative sites of the Jemez River-Rio Grande continuum (eight stream orders), in New Mexico (USA). For each stream order, we used a set of 6 columns packed with 3 different sediments, i.e., Silica Cone Density Sand ASTM D 1556 (0.075-2.00 mm), gravel (> 2mm) and native sediments from each site. We incubated the sediments for three months and performed tracer experiments in the laboratory under identical flow conditions, seeking to normalize the physical processes along the river continuum. We added a short-term pulse injection of NO3, resazurin and NaCl to each column and determined metabolism and NO3 processing using the Tracer Additions for Spiraling Curve Characterization method (TASCC). Our methods allowed us to study how changes in bacterial communities and sediment composition along the river continuum define nutrient processing.

  15. Feasibility Study for Monitoring Actinide Elements in Process Materials Using FO-LIBS at Advanced spent fuel Conditioning Process Facility

    Energy Technology Data Exchange (ETDEWEB)

    Han, Bo-Young; Choi, Daewoong; Park, Se Hwan; Kim, Ho-Dong [Nonproliferation System Research Division, Korea Atomic Energy Research Institute, Daejeon, 305-353 (Korea, Republic of); Dae, Dongsun [Department of Chemistry, Mokpo National University, Jeonnam 534-729 (Korea, Republic of); Whitehouse, Andrew I. [Applied Photonics Ltd., Unit 8 Carleton Business Park, Skipton, North Yorkshire BD23 2DE (United Kingdom)

    2015-07-01

    Korea Atomic Energy Research Institute (KAERI) have been developing the design and deployment methodology of Laser- Induced Breakdown Spectroscopy (LIBS) instrument for safeguards application within the argon hot cell environment at Advanced spent fuel Conditioning Process Facility (ACPF), where ACPF is a facility being refurbished for the laboratory-scaled demonstration of advanced spent fuel conditioning process. LIBS is an analysis technology used to measure the emission spectra of excited elements in the local plasma of a target material induced by a laser. The spectra measured by LIBS are analyzed to verify the quality and quantity of the specific element in the target matrix. Recently LIBS has been recognized as a promising technology for safeguards purposes in terms of several advantages including a simple sample preparation and in-situ analysis capability. In particular, a feasibility study of LIBS to remotely monitor the nuclear material in a high radiation environment has been carried out for supporting the IAEA safeguards implementation. Fiber-Optic LIBS (FO-LIBS) deployment was proposed by Applied Photonics Ltd because the use of fiber optics had benefited applications of LIBS by delivering the laser energy to the target and by collecting the plasma light. The design of FO-LIBS instrument for the measurement of actinides in the spent fuel and high temperature molten salt at ACPF had been developed in cooperation with Applied Photonics Ltd. FO-LIBS has some advantages as followings: the detectable plasma light wavelength range is not limited by the optical properties of the thick lead-glass shield window and the potential risk of laser damage to the lead-glass shield window is not considered. The remote LIBS instrument had been installed at ACPF and then the feasibility study for monitoring actinide elements such as uranium, plutonium, and curium in process materials has been carried out. (authors)

  16. Feasibility Study for Monitoring Actinide Elements in Process Materials Using FO-LIBS at Advanced spent fuel Conditioning Process Facility

    International Nuclear Information System (INIS)

    Han, Bo-Young; Choi, Daewoong; Park, Se Hwan; Kim, Ho-Dong; Dae, Dongsun; Whitehouse, Andrew I.

    2015-01-01

    Korea Atomic Energy Research Institute (KAERI) have been developing the design and deployment methodology of Laser- Induced Breakdown Spectroscopy (LIBS) instrument for safeguards application within the argon hot cell environment at Advanced spent fuel Conditioning Process Facility (ACPF), where ACPF is a facility being refurbished for the laboratory-scaled demonstration of advanced spent fuel conditioning process. LIBS is an analysis technology used to measure the emission spectra of excited elements in the local plasma of a target material induced by a laser. The spectra measured by LIBS are analyzed to verify the quality and quantity of the specific element in the target matrix. Recently LIBS has been recognized as a promising technology for safeguards purposes in terms of several advantages including a simple sample preparation and in-situ analysis capability. In particular, a feasibility study of LIBS to remotely monitor the nuclear material in a high radiation environment has been carried out for supporting the IAEA safeguards implementation. Fiber-Optic LIBS (FO-LIBS) deployment was proposed by Applied Photonics Ltd because the use of fiber optics had benefited applications of LIBS by delivering the laser energy to the target and by collecting the plasma light. The design of FO-LIBS instrument for the measurement of actinides in the spent fuel and high temperature molten salt at ACPF had been developed in cooperation with Applied Photonics Ltd. FO-LIBS has some advantages as followings: the detectable plasma light wavelength range is not limited by the optical properties of the thick lead-glass shield window and the potential risk of laser damage to the lead-glass shield window is not considered. The remote LIBS instrument had been installed at ACPF and then the feasibility study for monitoring actinide elements such as uranium, plutonium, and curium in process materials has been carried out. (authors)

  17. Effect of processing conditions on oil point pressure of moringa oleifera seed.

    Science.gov (United States)

    Aviara, N A; Musa, W B; Owolarafe, O K; Ogunsina, B S; Oluwole, F A

    2015-07-01

    Seed oil expression is an important economic venture in rural Nigeria. The traditional techniques of carrying out the operation is not only energy sapping and time consuming but also wasteful. In order to reduce the tedium involved in the expression of oil from moringa oleifera seed and develop efficient equipment for carrying out the operation, the oil point pressure of the seed was determined under different processing conditions using a laboratory press. The processing conditions employed were moisture content (4.78, 6.00, 8.00 and 10.00 % wet basis), heating temperature (50, 70, 85 and 100 °C) and heating time (15, 20, 25 and 30 min). Results showed that the oil point pressure increased with increase in seed moisture content, but decreased with increase in heating temperature and heating time within the above ranges. Highest oil point pressure value of 1.1239 MPa was obtained at the processing conditions of 10.00 % moisture content, 50 °C heating temperature and 15 min heating time. The lowest oil point pressure obtained was 0.3164 MPa and it occurred at the moisture content of 4.78 %, heating temperature of 100 °C and heating time of 30 min. Analysis of Variance (ANOVA) showed that all the processing variables and their interactions had significant effect on the oil point pressure of moringa oleifera seed at 1 % level of significance. This was further demonstrated using Response Surface Methodology (RSM). Tukey's test and Duncan's Multiple Range Analysis successfully separated the means and a multiple regression equation was used to express the relationship existing between the oil point pressure of moringa oleifera seed and its moisture content, processing temperature, heating time and their interactions. The model yielded coefficients that enabled the oil point pressure of the seed to be predicted with very high coefficient of determination.

  18. Effect of process operating conditions in the biomass torrefaction: A simulation study using one-dimensional reactor and process model

    International Nuclear Information System (INIS)

    Park, Chansaem; Zahid, Umer; Lee, Sangho; Han, Chonghun

    2015-01-01

    Torrefaction reactor model is required for the development of reactor and process design for biomass torrefaction. In this study, a one-dimensional reactor model is developed based on the kinetic model describing volatiles components and solid evolution and the existing thermochemical model considering the heat and mass balance. The developed reactor model used the temperature and flow rate of the recycled gas as the practical manipulated variables instead of the torrefaction temperature. The temperature profiles of the gas and solid phase were generated, depending on the practical thermal conditions, using developed model. Moreover, the effect of each selected operating variables on the parameters of the torrefaction process and the effect of whole operating variables with particular energy yield were analyzed. Through the results of sensitivity analysis, it is shown that the residence time insignificantly influenced the energy yield when the flow rate of recycled gas is low. Moreover, higher temperature of recycled gas with low flow rate and residence time produces the attractive properties, including HHV and grindability, of torrefied biomass when the energy yield is specified. - Highlights: • A one-dimensional reactor model for biomass torrefaction is developed considering the heat and mass balance. • The developed reactor model uses the temperature and flow rate of the recycled gas as the practical manipulated variables. • The effect of operating variables on the parameters of the torrefaction process is analyzed. • The results of sensitivity analysis represent notable discussions which were not done by the previous researches

  19. An atmospheric dispersion model for linear sources in calm wind, stable conditions; Un modello di dispersione atmosferica per sorgenti lineari in condizioni di vento debole

    Energy Technology Data Exchange (ETDEWEB)

    Cirillo, M. C. [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dipt. Ambiente; Buratti, D. [Rome Univ. La Sapienza, Rome (Italy). Facolta' di Scienze Statistiche; Metallo, M. C.; Poli, A.A. [ESA s.a.s., Bracciano, RM (Italy)

    1999-07-01

    In this report a dispersion model is proposed that provides an estimate of concentration of gaseous pollutants emitted by an highway, or in general by a line source, in presence of low wind speed. This aim was pursued because available models have not a satisfactory behaviour in such conditions, which is critical for dispersion of gaseous pollutants. This lack is due to difficulty of simulating dispersion turbulent component which is determined by fluctuation of wind speed and wind direction, and in presence of calm conditions it assumes values comparable with transport component. The proposed model overcomes this difficulty, as it is shown by sensitivity analysis and comparison with experimental data. The capability of simulating dispersion eve in critical conditions, like the presence of low level inversion, and the absence of source geometrical approximations make the model a tool that, properly used, may contribute to the efficient planning and management of environmental resources. [Italian] In questo rapporto viene proposto un modello per la stima delle concentrazioni di inquinanti aeriformi emessi da un'arteria stradale, o in generale da una sorgente lineare, in presenza di vento debole. Questo scopo e' stato perseguito in quanto in questa condizione, nonostante la dispersione degli inquinanti risulti fortemente problematica, i modelli disponibili in letteratura non hanno un comportamento soddisfacente. Questa mancanca e' attribuibile alla difficolta' di simulare la componente turbolenta della dispersione, dovuta alla fluttuazione della direzione e della velocita' del vento che, in presenza di vento debole, assume valori confrontabili alla componente di trasporto. Il modello qui di seguito proposto supera questa difficolta', come dimostrano l'analisi di sensibilita' e il confronto con un caso reale; la capacita' di simulare la dispersione anche in condizioni fisicamente critiche quali la presenza di inversione a

  20. Existence conditions of optimal trajectories in dynamic control processes; Conditions d'existence de trajectoires optimales des processus dynamiques commandes

    Energy Technology Data Exchange (ETDEWEB)

    Bonnemay-Juricek, L [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1968-07-01

    The existence of solutions in the optimal control problems with free endpoints is studied in this report and existence conditions are established without the usual assumption that the control region is convex. Furthermore the results, in order to be of some utility in physical applications, are expressed only by means of conditions on the parameters defining the system. (author) [French] Ce rapport etudie l'existence de solutions optimales dans les problemes de commande ou le point terminal est libre et ou la duree de l'evolution du systeme a optimiser est connue. Des conditions d'existence y sont formulees sans recourir a l'hypothese usuelle de convexite du domaine des valeurs des commandes. De plus on a cherche a rendre utilisables les resultats en ne faisant porter les conditions que sur les parametres directement accessibles du systeme. (auteur)

  1. MANAGEMENT SYSTEM OF THE ORGANIZATION PERFORMANCE INDICATORS IN THE CONDITIONS OF BUSINESS PROCESSES REALIZATION

    Directory of Open Access Journals (Sweden)

    Aleksandr Vladimirovich Gagarinskii

    2016-12-01

    Full Text Available This article discusses the problem of the effective work of managers of industrial enterprises, which is the basis of economic development in modern Russia. The authors suggest that the management of the system of performance indicators in managers in the conditions of realization of various business processes can reduce the risk of crises in the enterprise, and improve the efficiency of labour management and productivity in the company in a whole. According to the authors, improving the efficiency of management in the conditions of implementation of the various business processes of industrial enterprises is an integral element of the overall strategic development of the company. The article presents the results of work performance assessment of managers in the implementation of business process management. In this article there is developed performance business process management on the example of the metal cutting enterprise management levels: the corporate level, the first operational level, the second operational level, and the line level. For these indicators the performers are defined and criteria are given.

  2. Safer operating conditions and optimal scaling-up process for cyclohexanone peroxide reaction

    International Nuclear Information System (INIS)

    Zang, Na; Qian, Xin-Ming; Liu, Zhen-Yi; Shu, Chi-Min

    2015-01-01

    Highlights: • Thermal hazard of cyclohexanone peroxide reaction was measured by experimental techniques. • Levenberg–Marquardt algorithm was adopted to evaluate kinetic parameters. • Safer operating conditions at laboratory scale were acquired by BDs and TDs. • The verified safer operating conditions were used to obtain the optimal scale-up parameters applied in industrial plants. - Abstract: The cyclohexanone peroxide reaction process, one of the eighteen hazardous chemical processes identified in China, is performed in indirectly cooled semibatch reactors. The peroxide reaction is added to a mixture of hydrogen peroxide and nitric acid, which form heterogeneous liquid–liquid systems. A simple and general procedure for building boundary and temperature diagrams of peroxide process is given here to account for the overall kinetic expressions. Such a procedure has been validated by comparison with experimental data. Thermally safer operating parameters were obtained at laboratory scale, and the scaled-up procedure was performed to give the minimum dosing time in an industrial plant, which is in favor of maximizing industrial reactor productivity. The results are of great significance for governing the peroxide reaction process apart from the thermal runaway region. It also greatly aids in determining optimization on operating parameters in industrial plants.

  3. Towards a Kieselguhr- and PVPP-Free Clarification and Stabilization Process of Rough Beer at Room-Temperature Conditions.

    Science.gov (United States)

    Cimini, Alessio; Moresi, Mauro

    2018-01-01

    In this work, the main constraint (that is, beer chilling and chill haze removing) of the current beer conditioning techniques using Kieselguhr filtration and Polyvinylpolypyrrolidone (PVPP) treatment was overcome by developing a novel higher-throughput conditioning process, operating at room temperatures with no use of filter aids. The effect of filtration temperature (T F ) in the range of 0 to 40 °C on the hydraulic permeability of ceramic hollow-fiber (HF) membranes with nominal pore size of 0.2 to 1.4 μm, as well as on their limiting permeation flux (J * ) when feeding precentrifuged rough beer, was preliminarily assessed. When using the 1.4-μm HF membrane operating at T F ≥ 20 °C, it was possible to enhance the average permeation flux at values (676 to 1844 L/m 2 /h), noticeably higher than those (250 to 500 L/m 2 /h) characteristics of conventional powder filtration. Despite its acceptable permanent haze, the resulting beer permeate still exhibited colloidal instability. By resorting to the commercial enzyme preparation Brewers Clarex® before beer clarification, it was possible to significantly improve its colloidal stability as measured using a number of European Brewing Convention forcing tests, especially with respect to that of precentrifuged rough beer by itself. By combining the above enzymatic treatment with membrane clarification at 30 °C across the ceramic 1.4-μm HF membrane module, it was possible to limit the haze development due to chilling, sensitive proteins, and alcohol addition to as low as 0.78, 4.1, and 4.0 EBC-U, respectively, the enzymatic treatment being by far more effective than that using PVPP. A novel Kieselguhr- and PVPP-free rough beer conditioning process at room temperatures was set up. By submitting precentrifuged rough beer to commercial preparation Brewers Clarex ® and then to membrane clarification at 30 °C across a ceramic 1.4-μm hollow-fiber membrane module, it was possible to obtain a clear and stable beer with

  4. Panorama Image Processing for Condition Monitoring with Thermography in Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Jeon, Byoung Joon; Kim, Tae Hwan; Kim, Soon Geol; Mo, Yoon Syub [UNETWARE, Seoul (Korea, Republic of); Kim, Won Tae [Kongju National University, Gongju (Korea, Republic of)

    2010-04-15

    In this paper, imaging processing study obtained from CCD image and thermography image was performed in order to treat easily thermographic data without any risks of personnel who conduct the condition monitoring for the abnormal or failure status occurrable in industrial power plants. This imaging processing is also applicable to the predictive maintenance. For confirming the broad monitoring, a methodology producting single image from the panorama technique was developed no matter how many cameras are employed, including fusion method for discrete configuration for the target. As results, image fusion from quick realtime processing was obtained and it was possible to save time to track the location monitoring in matching the images between CCTV and thermography

  5. Panorama Image Processing for Condition Monitoring with Thermography in Power Plant

    International Nuclear Information System (INIS)

    Jeon, Byoung Joon; Kim, Tae Hwan; Kim, Soon Geol; Mo, Yoon Syub; Kim, Won Tae

    2010-01-01

    In this paper, imaging processing study obtained from CCD image and thermography image was performed in order to treat easily thermographic data without any risks of personnel who conduct the condition monitoring for the abnormal or failure status occurrable in industrial power plants. This imaging processing is also applicable to the predictive maintenance. For confirming the broad monitoring, a methodology producting single image from the panorama technique was developed no matter how many cameras are employed, including fusion method for discrete configuration for the target. As results, image fusion from quick realtime processing was obtained and it was possible to save time to track the location monitoring in matching the images between CCTV and thermography

  6. Effect of UHT processing and storage conditions on physico-chemical characteristics of buffalo skim milk

    International Nuclear Information System (INIS)

    Hussain, I.

    2011-01-01

    The obtained results indicated that physico-chemical and nutritional changes in UHT processed buffalo skimmed milk were more pronounced at 45 deg. C than 25 deg. C and 10 deg. C. Duration of storage adversely affected the chemical and nutritional quality of processed milk. A slight decrease in pH, total ash and lactose contents, was observed, whereas acidity was increased on the mentioned storage conditions. Total nitrogen and casein nitrogen contents gradually decreased during storage, whereas non-casein nitrogen (NCN) and non-protein nitrogen (NPN) increased to a great extent in samples stored at higher temperatures. A significant increase in hydroxyl methyl furfural (HMF) values occurred in UHT processed buffalo skim milk at 25 deg. C and 45 deg. C after of 90 days storage. Storage at high temperature (45 deg. C) caused undesirable effects on sensory properties, general quality characteristics and acceptability of UHT buffalo skimmed milk. (author)

  7. Effect of processing conditions on the mechanical properties of polypropylene/bentonite nano composites

    International Nuclear Information System (INIS)

    Alves, Tatianny S.; Cipriano, Pamela B.; Lira, Vanize F.; Canedo, Eduardo L.; Carvalho, Laura H. de

    2009-01-01

    This work dealt with the effect of processing conditions on the properties of polypropylene/bentonite compounds, using natural clay and an organoclay prepared with hexadecyl trimethyl ammonium bromide. Compounds with 1% clay were prepared by melt compounding in a single-screw extruder and in a counter-rotating twin-screw extruder, and characterized x-ray diffraction; tensile and impact mechanical tests. X ray diffraction results on clays and compounds show that the surfactant was incorporated within the clay galleries and that intercalated nano composites were obtained with the organoclay processed in either the single or the twin-screw extruder. The data also indicated that, without the addition of a compatibilizer, no significant variation of mechanical properties was observed for the composites processed in either extruder. (author)

  8. A study on the manufacturing conditions of metal matrix composites by low pressure infiltration process

    Energy Technology Data Exchange (ETDEWEB)

    Park, Won Jo; Hessian, Md Anowar; Park, Sung Ho [Gyeongsang National University, Tongyoung (Korea, Republic of); Huh, Sun Chul [Gyeongsang National University, JinJu (Korea, Republic of)

    2007-10-15

    Metal fiber preform reinforced aluminum alloy composite as made by the infiltration of molten metal under low pressure casting process. The infiltration behavior of filling pattern and the velocity profile with low-pressure casting process was investigated. The thermocouple was inserted into the preform in order to observe the infiltration behavior. The infiltration of applied pressure time, 1, 2 and 5 s under constant pressure of 0.4 MPa was completely filled during 0.4 s. In these conditions, molten aluminum alloy has successfully infiltrated to FeCrSi metal fiber preform by low-pressure casting process. It was observed the porosity of composites for reliability of composites. The automobile piston was developed with FeCrSi reinforced aluminum alloy that is 0% porosity by the optimal applied pressure and applied pressure time.

  9. Effects of reaction conditions on nuclear laundry water treatment in Fenton process

    International Nuclear Information System (INIS)

    Vilve, Miia; Hirvonen, Arja; Sillanpaeae, Mika

    2009-01-01

    This study presents the efficiency of Fenton process in the degradation of organic compounds of nuclear laundry water. The influence of Fe 2+ and hydrogen peroxide ratio, hydrogen peroxide dose, pH and treatment time were investigated. The degradation of non-ionic surfactant and other organic compounds was analysed as COD, TOC and molecular weight distribution (MWD). The most cost-effective degradation conditions were at H 2 O 2 /Fe 2+ stoichiometric molar ratio of 2 with 5 min mixing and H 2 O 2 dose of 1000 mg l -1 . With the initial pH of 6, the reductions of COD and TOC were 85% and 69%, respectively. However, the removal of the organic compounds was mainly carried out by Fenton-based Fe 3+ coagulation rather than Fenton oxidation. Fenton process proved to be much more efficient than previously performed ozone-based oxidation processes.

  10. Green synthesis of silver nanoparticles using Beta vulgaris: Role of process conditions on size distribution and surface structure

    Energy Technology Data Exchange (ETDEWEB)

    Parameshwaran, R., E-mail: parameshviews@gmail.com [Department of Mechanical Engineering, Anna University, Chennai 600 025 (India); Centre for Nanoscience and Technology, Anna University, Chennai 600 025 (India); Kalaiselvam, S., E-mail: kalai@annauniv.edu [Centre for Nanoscience and Technology, Anna University, Chennai 600 025 (India); Department of Applied Science and Technology, Anna University, Chennai 600 025 (India); Jayavel, R., E-mail: rjvel@annauniv.edu [Centre for Nanoscience and Technology, Anna University, Chennai 600 025 (India)

    2013-06-15

    The present work reports the green synthesis of silver nanoparticles, using Beta vulgaris peel extract with a subsequent investigation on the size distribution and surface structure of nanoparticles formed under various process conditions. The green-chemical reduction mechanism of silver ions to nanoparticles by the active organic functional groups present in the extract was characterized, using the respective spectroscopic techniques. The effects of various process parameters, including induced intraparticle ripening, were attributed to the controlled formation of anisotropic silver nanoparticles within the supporting matrix of the extract. The plasmon absorption and resonance scattering properties were expected to be favourable for small and larger size nanoparticles (below 25 nm and above 75 nm) respectively, which was considered to be an indicative aspect for synthesizing nanoparticles of narrow size distribution. The zeta potential and dynamic light scattering (DLS) results suggest the good stability and mono-dispersed size distribution of the silver nanoparticles. The transmission electron microscope, selective area electron diffraction (SAED) and X-ray diffraction studies infer that the nanoparticles formed were spherical/quasi-spherical in shape, which primarily exhibited a face centred cubic crystal (FCC) structure. The green-chemical reduction of organic phases in the extract (especially amine (NH{sub 2}) groups) as reflected through shifts observed in the Fourier-transform infra red (FTIR) peaks, reveal the possible interaction of the organic molecules with the silver ions in the effective formation, surface modification and stabilization of the silver nanoparticles. - Highlights: • Functionally stable and crystalline silver nanoparticles were green synthesized. • Beta vulgaris peel extract was used as potential reducing and stabilizing agent. • Amine groups in extract were expected to reduce Ag{sup +} and stabilize nanoparticles. • Induced

  11. Green synthesis of silver nanoparticles using Beta vulgaris: Role of process conditions on size distribution and surface structure

    International Nuclear Information System (INIS)

    Parameshwaran, R.; Kalaiselvam, S.; Jayavel, R.

    2013-01-01

    The present work reports the green synthesis of silver nanoparticles, using Beta vulgaris peel extract with a subsequent investigation on the size distribution and surface structure of nanoparticles formed under various process conditions. The green-chemical reduction mechanism of silver ions to nanoparticles by the active organic functional groups present in the extract was characterized, using the respective spectroscopic techniques. The effects of various process parameters, including induced intraparticle ripening, were attributed to the controlled formation of anisotropic silver nanoparticles within the supporting matrix of the extract. The plasmon absorption and resonance scattering properties were expected to be favourable for small and larger size nanoparticles (below 25 nm and above 75 nm) respectively, which was considered to be an indicative aspect for synthesizing nanoparticles of narrow size distribution. The zeta potential and dynamic light scattering (DLS) results suggest the good stability and mono-dispersed size distribution of the silver nanoparticles. The transmission electron microscope, selective area electron diffraction (SAED) and X-ray diffraction studies infer that the nanoparticles formed were spherical/quasi-spherical in shape, which primarily exhibited a face centred cubic crystal (FCC) structure. The green-chemical reduction of organic phases in the extract (especially amine (NH 2 ) groups) as reflected through shifts observed in the Fourier-transform infra red (FTIR) peaks, reveal the possible interaction of the organic molecules with the silver ions in the effective formation, surface modification and stabilization of the silver nanoparticles. - Highlights: • Functionally stable and crystalline silver nanoparticles were green synthesized. • Beta vulgaris peel extract was used as potential reducing and stabilizing agent. • Amine groups in extract were expected to reduce Ag + and stabilize nanoparticles. • Induced intraparticle

  12. Impacts of Combustion Conditions and Photochemical Processing on the Light Absorption of Biomass Combustion Aerosol.

    Science.gov (United States)

    Martinsson, J; Eriksson, A C; Nielsen, I Elbæk; Malmborg, V Berg; Ahlberg, E; Andersen, C; Lindgren, R; Nyström, R; Nordin, E Z; Brune, W H; Svenningsson, B; Swietlicki, E; Boman, C; Pagels, J H

    2015-12-15

    The aim was to identify relationships between combustion conditions, particle characteristics, and optical properties of fresh and photochemically processed emissions from biomass combustion. The combustion conditions included nominal and high burn rate operation and individual combustion phases from a conventional wood stove. Low temperature pyrolysis upon fuel addition resulted in "tar-ball" type particles dominated by organic aerosol with an absorption Ångström exponent (AAE) of 2.5-2.7 and estimated Brown Carbon contributions of 50-70% to absorption at the climate relevant aethalometer-wavelength (520 nm). High temperature combustion during the intermediate (flaming) phase was dominated by soot agglomerates with AAE 1.0-1.2 and 85-100% of absorption at 520 nm attributed to Black Carbon. Intense photochemical processing of high burn rate flaming combustion emissions in an oxidation flow reactor led to strong formation of Secondary Organic Aerosol, with no or weak absorption. PM1 mass emission factors (mg/kg) of fresh emissions were about an order of magnitude higher for low temperature pyrolysis compared to high temperature combustion. However, emission factors describing the absorption cross section emitted per kg of fuel consumed (m(2)/kg) were of similar magnitude at 520 nm for the diverse combustion conditions investigated in this study. These results provide a link between biomass combustion conditions, emitted particle types, and their optical properties in fresh and processed plumes which can be of value for source apportionment and balanced mitigation of biomass combustion emissions from a climate and health perspective.

  13. Performance evaluation of the DCMD desalination process under bench scale and large scale module operating conditions

    KAUST Repository

    Francis, Lijo; Ghaffour, NorEddine; Alsaadi, Ahmad Salem; Nunes, Suzana Pereira; Amy, Gary L.

    2014-01-01

    The flux performance of different hydrophobic microporous flat sheet commercial membranes made of poly tetrafluoroethylene (PTFE) and poly propylene (PP) was tested for Red Sea water desalination using the direct contact membrane distillation (DCMD) process, under bench scale (high δT) and large scale module (low δT) operating conditions. Membranes were characterized for their surface morphology, water contact angle, thickness, porosity, pore size and pore size distribution. The DCMD process performance was optimized using a locally designed and fabricated module aiming to maximize the flux at different levels of operating parameters, mainly feed water and coolant inlet temperatures at different temperature differences across the membrane (δT). Water vapor flux of 88.8kg/m2h was obtained using a PTFE membrane at high δT (60°C). In addition, the flux performance was compared to the first generation of a new locally synthesized and fabricated membrane made of a different class of polymer under the same conditions. A total salt rejection of 99.99% and boron rejection of 99.41% were achieved under extreme operating conditions. On the other hand, a detailed water characterization revealed that low molecular weight non-ionic molecules (ppb level) were transported with the water vapor molecules through the membrane structure. The membrane which provided the highest flux was then tested under large scale module operating conditions. The average flux of the latter study (low δT) was found to be eight times lower than that of the bench scale (high δT) operating conditions.

  14. Performance evaluation of the DCMD desalination process under bench scale and large scale module operating conditions

    KAUST Repository

    Francis, Lijo

    2014-04-01

    The flux performance of different hydrophobic microporous flat sheet commercial membranes made of poly tetrafluoroethylene (PTFE) and poly propylene (PP) was tested for Red Sea water desalination using the direct contact membrane distillation (DCMD) process, under bench scale (high δT) and large scale module (low δT) operating conditions. Membranes were characterized for their surface morphology, water contact angle, thickness, porosity, pore size and pore size distribution. The DCMD process performance was optimized using a locally designed and fabricated module aiming to maximize the flux at different levels of operating parameters, mainly feed water and coolant inlet temperatures at different temperature differences across the membrane (δT). Water vapor flux of 88.8kg/m2h was obtained using a PTFE membrane at high δT (60°C). In addition, the flux performance was compared to the first generation of a new locally synthesized and fabricated membrane made of a different class of polymer under the same conditions. A total salt rejection of 99.99% and boron rejection of 99.41% were achieved under extreme operating conditions. On the other hand, a detailed water characterization revealed that low molecular weight non-ionic molecules (ppb level) were transported with the water vapor molecules through the membrane structure. The membrane which provided the highest flux was then tested under large scale module operating conditions. The average flux of the latter study (low δT) was found to be eight times lower than that of the bench scale (high δT) operating conditions.

  15. Analysis of metal forming processes by using physical modeling and new plastic similarity condition

    International Nuclear Information System (INIS)

    Gronostajski, Z.; Hawryluk, M.

    2007-01-01

    In recent years many advances have been made in numerical methods, for linear and non-linear problems. However the success of them depends very much on the correctness of the problem formulation and the availability of the input data. Validity of the theoretical results can be verified by an experiment using the real or soft materials. An essential reduction of time and costs of the experiment can be obtained by using soft materials, which behaves in a way analogous to that of real metal during deformation. The advantages of using of the soft materials are closely connected with flow stress 500 to 1000 times lower than real materials. The accuracy of physical modeling depend on the similarity conditions between physical model and real process. The most important similarity conditions are materials similarity in the range of plastic and elastic deformation, geometrical, frictional and thermal similarities. New original plastic similarity condition for physical modeling of metal forming processes is proposed in the paper. It bases on the mathematical description of similarity of the flow stress curves of soft materials and real ones

  16. Effects of Processing Conditions During Manufacture on Retronasal-Aroma Compounds from a Milk Coffee Drink.

    Science.gov (United States)

    Ikeda, Michio; Akiyama, Masayuki; Hirano, Yuta; Miyazi, Kazuhiro; Kono, Masaya; Imayoshi, Yuriko; Iwabuchi, Hisakatsu; Onodera, Takeshi; Toko, Kiyoshi

    2018-03-01

    To develop a ready-to-drink (RTD) milk coffee retaining the original coffee flavor, the effects of processing conditions during manufacture on retronasal-arma (RA) compounds from the milk coffee were investigated by gas chromatography-mass spectrometry using an RA simulator (RAS). Thirteen of 46 detected compounds in the RAS effluent (RAS compounds) decreased significantly following pH adjustment of coffee (from pH 5.1 to 6.8) and 5 compounds increased. RAS compounds from coffee tended to decrease through the pH adjustment and subsequent sterilization. Significantly higher amounts of 13 RAS compounds were released from the milk coffee produced using a blending-after-sterilization (BAS) process without the pH adjustment than from that using a blending-before-sterilization (BBS) process with the pH adjustment. In BAS-processed milk coffee, significantly lower amounts of 8 high-volatility compounds and 1H-pyrrole were released from coffee containing infusion-sterilized (INF) milk than from coffee containing plate-sterilized (PLT) milk, whereas 3 low-volatility compounds were released significantly more from coffee using PLT milk. Principal component analysis revealed that the effect of the manufacturing process (BAS, BBS, or homemade (blending unsterilized coffee without pH adjustment with sterilized milk)) on milk coffee volatiles was larger than that of the sterilization method (INF or PLT) for milk, and that the sterilization method could result in different RAS volatile characteristics in BAS and homemade processes. In conclusion, a BAS process was found to be superior to a BBS process for the manufacture of an RTD milk coffee that retains volatile characteristics similar to that of a homemade milk coffee. Ready-to-drink (RTD) milk coffee manufactured using the conventional blending-before-sterilization process does not retain its original coffee flavor due to pH adjustment of the coffee during the process. The new blending-after-sterilization (BAS) process

  17. Mathematical Modelling of Thermal Process to Aquatic Environment with Different Hydrometeorological Conditions

    Directory of Open Access Journals (Sweden)

    Alibek Issakhov

    2014-01-01

    Full Text Available This paper presents the mathematical model of the thermal process from thermal power plant to aquatic environment of the reservoir-cooler, which is located in the Pavlodar region, 17 Km to the north-east of Ekibastuz town. The thermal process in reservoir-cooler with different hydrometeorological conditions is considered, which is solved by three-dimensional Navier-Stokes equations and temperature equation for an incompressible flow in a stratified medium. A numerical method based on the projection method, divides the problem into three stages. At the first stage, it is assumed that the transfer of momentum occurs only by convection and diffusion. Intermediate velocity field is solved by fractional steps method. At the second stage, three-dimensional Poisson equation is solved by the Fourier method in combination with tridiagonal matrix method (Thomas algorithm. Finally, at the third stage, it is expected that the transfer is only due to the pressure gradient. Numerical method determines the basic laws of the hydrothermal processes that qualitatively and quantitatively are approximated depending on different hydrometeorological conditions.

  18. Lipolysis and lipid oxidation in fermented sausages depending on different processing conditions and different antioxidants.

    Science.gov (United States)

    Zanardi, Emanuela; Ghidini, Sergio; Battaglia, Alessandra; Chizzolini, Roberto

    2004-02-01

    Lipolysis and lipid oxidation in Mediterranean and North Europe type sausages were studied in relation to raw material, processing conditions and additives. In particular the effect of ascorbic acid, nitrites and spices was evaluated. Lipolysis was measured by the determination of total and free fatty acids of fresh minces and matured products and lipid oxidation was evaluated by thiobarbituric acid reactive substances and cholesterol oxidation products. The increase of free fatty acids during maturation appears to be independent from processing conditions and the differences in polyunsaturated fatty acids increment found among the formulations appear to be due to inherent variations of raw materials. The presence of ascorbic acid and/or nitrite seems important for cholesterol protection and, as a consequence, for the safety of fermented meat products while spices at doses up to 0.1% do not seem to have a remarkable effect. The effect on fatty acid oxidation of the same additives and of the different processing technologies is not significantly different and the variations linked to raw material may play the greatest role.

  19. A study on optimum conditions for reducing Polonium-210 ion in electrolysis process

    International Nuclear Information System (INIS)

    Yii Mei Wo

    2006-01-01

    Polonium-210 is one of the most important radionuclide to be study while studying radioactive contaminants on marine lives. It usually be self-deposited on a pure silver foil and counted using an Alpha Spectrometry System. However, using pure silver foil involves high cost. Therefore, study had been conducted to find the suitability of using stainless steel disc to deposit polonium-210 using electrolysis process and the optimum conditions for such process. This was carry out by using pure polonium-210 standard solution and the ready disc was counted using Zinc Sulphite Counter. Results show that reduction of polonium ion on stainless steel disc can be done but the efficiency of the process only around 70 percent. Besides this, studies also show that, at 1.1 ampere constant current and cathode to anode distance at 8 mm, the optimum conditions to reduce polonium ion were at pH 2.2-2.3 with the electrolysis time of 5 hours. (Author)

  20. Depolarization current relaxation process of insulating dielectrics after corona poling under different charging conditions

    Directory of Open Access Journals (Sweden)

    J. W. Zhang

    2017-10-01

    Full Text Available As an insulating dielectric, polyimide is favorable for the application of optoelectronics, electrical insulation system in electric power industry, insulating, and packaging materials in space aircraft, due to its excellent thermal, mechanical and electrical insulating stability. The charge storage profile of such insulating dielectric is utmost important to its application, when it is exposed to electron irradiation, high voltage corona discharge or other treatments. These treatments could induce changes in physical and chemical properties of treated samples. To investigate the charge storage mechanism of the insulating dielectrics after high-voltage corona discharge, the relaxation processes responsible for corona charged polyimide films under different poling conditions were analyzed by the Thermally Stimulated Discharge Currents method (TSDC. In the results of thermal relaxation process, the appearance of various peaks in TSDC spectra provided a deep insight into the molecular status in the dielectric material and reflected stored space charge relaxation process in the insulating polymers after corona discharge treatments. Furthermore, the different space charge distribution status under various poling temperature and different discharge voltage level were also investigated, which could partly reflect the influence of the ambiance condition on the functional dielectrics after corona poling.

  1. Depolarization current relaxation process of insulating dielectrics after corona poling under different charging conditions

    Science.gov (United States)

    Zhang, J. W.; Zhou, T. C.; Wang, J. X.; Yang, X. F.; Zhu, F.; Tian, L. M.; Liu, R. T.

    2017-10-01

    As an insulating dielectric, polyimide is favorable for the application of optoelectronics, electrical insulation system in electric power industry, insulating, and packaging materials in space aircraft, due to its excellent thermal, mechanical and electrical insulating stability. The charge storage profile of such insulating dielectric is utmost important to its application, when it is exposed to electron irradiation, high voltage corona discharge or other treatments. These treatments could induce changes in physical and chemical properties of treated samples. To investigate the charge storage mechanism of the insulating dielectrics after high-voltage corona discharge, the relaxation processes responsible for corona charged polyimide films under different poling conditions were analyzed by the Thermally Stimulated Discharge Currents method (TSDC). In the results of thermal relaxation process, the appearance of various peaks in TSDC spectra provided a deep insight into the molecular status in the dielectric material and reflected stored space charge relaxation process in the insulating polymers after corona discharge treatments. Furthermore, the different space charge distribution status under various poling temperature and different discharge voltage level were also investigated, which could partly reflect the influence of the ambiance condition on the functional dielectrics after corona poling.

  2. Application of Fourier transform near-infrared spectroscopy to optimization of green tea steaming process conditions.

    Science.gov (United States)

    Ono, Daiki; Bamba, Takeshi; Oku, Yuichi; Yonetani, Tsutomu; Fukusaki, Eiichiro

    2011-09-01

    In this study, we constructed prediction models by metabolic fingerprinting of fresh green tea leaves using Fourier transform near-infrared (FT-NIR) spectroscopy and partial least squares (PLS) regression analysis to objectively optimize of the steaming process conditions in green tea manufacture. The steaming process is the most important step for manufacturing high quality green tea products. However, the parameter setting of the steamer is currently determined subjectively by the manufacturer. Therefore, a simple and robust system that can be used to objectively set the steaming process parameters is necessary. We focused on FT-NIR spectroscopy because of its simple operation, quick measurement, and low running costs. After removal of noise in the spectral data by principal component analysis (PCA), PLS regression analysis was performed using spectral information as independent variables, and the steaming parameters set by experienced manufacturers as dependent variables. The prediction models were successfully constructed with satisfactory accuracy. Moreover, the results of the demonstrated experiment suggested that the green tea steaming process parameters could be predicted on a larger manufacturing scale. This technique will contribute to improvement of the quality and productivity of green tea because it can objectively optimize the complicated green tea steaming process and will be suitable for practical use in green tea manufacture. Copyright © 2011 The Society for Biotechnology, Japan. Published by Elsevier B.V. All rights reserved.

  3. [Process development for continuous ethanol fermentation by the flocculating yeast under stillage backset conditions].

    Science.gov (United States)

    Zi, Lihan; Liu, Chenguang; Bai, Fengwu

    2014-02-01

    Propionic acid, a major inhibitor to yeast cells, was accumulated during continuous ethanol fermentation from corn meal hydrolysate by the flocculating yeast under stillage backset conditions. Based on its inhibition mechanism in yeast cells, strategies were developed for alleviating this effect. Firstly, high temperature processes such as medium sterilization generated more propionic acid, which should be avoided. Propionic acid was reduced significantly during ethanol fermentation without medium sterilization, and concentrations of biomass and ethanol increased by 59.3% and 7.4%, respectively. Secondly, the running time of stillage backset should be controlled so that propionic acid accumulated would be lower than its half inhibition concentration IC50 (40 mmol/L). Finally, because low pH augmented propionic acid inhibition in yeast cells, a higher pH of 5.5 was validated to be suitable for ethanol fermentation under the stillage backset condition.

  4. Cognitive processing load across a wide range of listening conditions: insights from pupillometry.

    Science.gov (United States)

    Zekveld, Adriana A; Kramer, Sophia E

    2014-03-01

    The pupil response to speech masked by interfering speech was assessed across an intelligibility range from 0% to 99% correct. In total, 37 participants aged between 18 and 36 years and with normal hearing were included. Pupil dilation was largest at intermediate intelligibility levels, smaller at high intelligibility, and slightly smaller at very difficult levels. Participants who reported that they often gave up listening at low intelligibility levels had smaller pupil dilations in these conditions. Participants who were good at reading masked text had relatively large pupil dilation when intelligibility was low. We conclude that the pupil response is sensitive to processing load, and possibly reflects cognitive overload in difficult conditions. It seems affected by methodological aspects and individual abilities, but does not reflect subjective ratings. Copyright © 2014 Society for Psychophysiological Research.

  5. Conditional analysis of mixed Poisson processes with baseline counts: implications for trial design and analysis.

    Science.gov (United States)

    Cook, Richard J; Wei, Wei

    2003-07-01

    The design of clinical trials is typically based on marginal comparisons of a primary response under two or more treatments. The considerable gains in efficiency afforded by models conditional on one or more baseline responses has been extensively studied for Gaussian models. The purpose of this article is to present methods for the design and analysis of clinical trials in which the response is a count or a point process, and a corresponding baseline count is available prior to randomization. The methods are based on a conditional negative binomial model for the response given the baseline count and can be used to examine the effect of introducing selection criteria on power and sample size requirements. We show that designs based on this approach are more efficient than those proposed by McMahon et al. (1994).

  6. Investigation of heat treatment conditions of structural material for blanket fabrication process

    International Nuclear Information System (INIS)

    Hirose, Takanori; Suzuki, Satoshi; Akiba, Masato; Shiba, Kiyoyuki; Sawai, Tomotsugu; Jitsukawa, Shiro

    2004-01-01

    This paper presents recent results of thermal hysteresis effects on ceramic breeder blanket structural material. Reduced activation ferritic/martensitic (RAF) steel is the leading candidates for the first wall structural materials of breeding blankets. RAF steel demonstrates superior resistance to high dose neutron irradiation, because the steel has tempered martensite structure which contains the number of sink site for radiation defects. This microstructure obtained by two-step heat treatment, first is normalizing at temperature above 1200 K and the second is tempering at temperature below 1100 K. Recent study revealed the thermal hysteresis has significant impacts on the post-irradiation mechanical properties. The breeding blanket has complicated structure, which consists of tungsten armor and thin first wall with cooling pipe. The blanket fabrication requires some high temperature joining processes. Especially hot isostatic pressing (HIP) is examined as a near-net-shape fabrication process for this structure. The process consists of heating above 1300 K and isostatic pressing at the pressure above 150 MPa followed by tempering. Moreover ceramics pebbles are packed into blanket module and the module is to be seamed by welding followed by post weld heat treatment in the final assemble process. Therefore the final microstructural features of RAFs strongly depend on the blanket fabrication process. The objective of this work is to evaluate the effects of thermal hysteresis corresponding to blanket fabrication process on RAFs microstructure in order to establish appropriate blanket fabrication process. Japanese RAFs F82H (Fe-0.1C-8Cr-2W-0.2V-0.05Ta) was investigated by metallurgical method after isochronal heat treatment up to 1473 K simulating high temperature bonding process. Although F82H showed significant grain growth after conventional solid HIP conditions (1313 K x 2 hr.), this coarse grained microstructure was refined by the post HIP normalizing at

  7. In-soil radon anomalies as precursors of earthquakes: a case study in the SE slope of Mt. Etna in a period of quite stable weather conditions

    International Nuclear Information System (INIS)

    Vizzini, Fabio; Brai, Maria

    2012-01-01

    In-soil radon concentrations as well as climatic parameters (temperature, atmospheric pressure and relative humidity) were collected in St. Venerina (Eastern Sicily – Italy) from March 19th to May 22nd 2009, close to an active fault system called Timpe Fault System (TFS), which is strictly linked to the geodynamics of Mt. Etna. During the monitoring period no drastic climatic variations were observed and, on the other hand, important seismic events were recorded close to the monitoring site. A seismic swarm composed of 5 earthquakes was observed in the Milo area on March 25th (M max = 2.7) at just 5.1 km from the site, and on May 13th an earthquake of 3.6 magnitude was recorded in the territory of St. Venerina, at just 3.2 km from the site; the earthquake was felt by the population and reported by all local and regional media. The in-soil radon concentrations have shown anomalous increases possibly linked to the earthquakes recorded, but certainly not attributable to local meteorology. To verify this assumption the average radon concentration and the standard deviation (σ) have been calculated and the regions of ±1.5σ and ±2σ deviation from the average concentration have been investigated. Moreover, to further minimise the contribution of the meteorological parameters on the in-soil radon fluctuations, a multiple regressions method has been used. To distinguish those earthquakes which could generate in-soil radon anomalies as precursors, the Dobrovolsky radius has been applied. The results obtained suggests that a clear correlation between earthquakes and in-soil radon increases exist, and that the detection of the in-soil radon anomalies becomes surely simpler in particular favourable conditions: weather stability, earthquakes within the Dobrovolsky radius and close to the monitoring area. Moreover, the absence of large variations of the climatic parameters, which could generate incoherent noise components to the radon signal, has made the radon

  8. In-soil radon anomalies as precursors of earthquakes: a case study in the SE slope of Mt. Etna in a period of quite stable weather conditions.

    Science.gov (United States)

    Vizzini, Fabio; Brai, Maria

    2012-11-01

    In-soil radon concentrations as well as climatic parameters (temperature, atmospheric pressure and relative humidity) were collected in St. Venerina (Eastern Sicily - Italy) from March 19th to May 22nd 2009, close to an active fault system called Timpe Fault System (TFS), which is strictly linked to the geodynamics of Mt. Etna. During the monitoring period no drastic climatic variations were observed and, on the other hand, important seismic events were recorded close to the monitoring site. A seismic swarm composed of 5 earthquakes was observed in the Milo area on March 25th (M(max) = 2.7) at just 5.1 km from the site, and on May 13th an earthquake of 3.6 magnitude was recorded in the territory of St. Venerina, at just 3.2 km from the site; the earthquake was felt by the population and reported by all local and regional media. The in-soil radon concentrations have shown anomalous increases possibly linked to the earthquakes recorded, but certainly not attributable to local meteorology. To verify this assumption the average radon concentration and the standard deviation (σ) have been calculated and the regions of ±1.5σ and ±2σ deviation from the average concentration have been investigated. Moreover, to further minimise the contribution of the meteorological parameters on the in-soil radon fluctuations, a multiple regressions method has been used. To distinguish those earthquakes which could generate in-soil radon anomalies as precursors, the Dobrovolsky radius has been applied. The results obtained suggests that a clear correlation between earthquakes and in-soil radon increases exist, and that the detection of the in-soil radon anomalies becomes surely simpler in particular favourable conditions: weather stability, earthquakes within the Dobrovolsky radius and close to the monitoring area. Moreover, the absence of large variations of the climatic parameters, which could generate incoherent noise components to the radon signal, has made the radon fluctuations

  9. Site-condition map for Portugal, Western Iberia: methodology and constraints on the performance of Vs30 proxies for stable continental regions in Europe.

    Science.gov (United States)

    Vilanova, S. P.; Narciso, J.; Carvalho, J. P.; Cancela, C.; Lopes, I.; Nemser, E. S.; Borges, J.

    2014-12-01

    Information on the amplification characteristics of the near-surface formations in a regional sense is essential to adequately represent both seismic hazard maps and ground shaking maps. Due to the scarceness of shear-wave velocity data in most regions, several methods have been proposed in order to obtain first order representations of Vs30. These include the surface geology method and the topographic slope method. The latter method has become the standard way for incorporating site effects into regional studies worldwide given the convenience provided by the global Vs30 Internet server. In the framework of project SCENE we developed a shear wave velocity database for Portugal. The database consists of 87 shear-wave velocity depth profiles from a variety of lithological and geological formations. We used an iterative three-step procedure to develop the Vs30 based site-condition map: 1) to define a preliminary set of geologically defined units based on the literature; 2) to calculate the distribution of Vs30 for each unit; and 3) to perform statistical tests in order to estimate the significance of the difference in the Vs30 distribution characteristics between the units. The units were merged according to the results of the statistical tests and the procedure was repeated. We started by classifying the sites into six generalized geological units. The final set consists of three units only: F1 (igneous, metamorphic and old sedimentary rocks); F2 (Neogene and Pleistocene formations); and F3 (Holocene deposits). We used the database to evaluate the performance of Vs30 proxies. The use of proxies based either on geological units or on correlations with the topographic slope shows relatively unbiased total residual distributions of the logarithm of Vs30. However, the performance of the methods varies significantly with the generalized geological unit analyzed. Both methods are biased towards lower values of Vs30 for rock formations. The topographic-slope method is

  10. Stable Isotope Data

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Tissue samples (skin, bone, blood, muscle) are analyzed for stable carbon, stable nitrogen, and stable sulfur analysis. Many samples are used in their entirety for...

  11. Influence of stress on fear memory processes in an aversive differential conditioning paradigm in humans.

    Science.gov (United States)

    Bentz, Dorothée; Michael, Tanja; Wilhelm, Frank H; Hartmann, Francina R; Kunz, Sabrina; von Rohr, Isabelle R Rudolf; de Quervain, Dominique J-F

    2013-07-01

    It is widely assumed that learning and memory processes play an important role in the pathogenesis, expression, maintenance and therapy of anxiety disorders, such as phobias or post-traumatic stress disorder (PTSD). Memory retrieval is involved in symptom expression and maintenance of these disorders, while memory extinction is believed to be the underlying mechanism of behavioral exposure therapy of anxiety disorders. There is abundant evidence that stress and stress hormones can reduce memory retrieval of emotional information, whereas they enhance memory consolidation of extinction training. In this study we aimed at investigating if stress affects these memory processes in a fear conditioning paradigm in healthy human subjects. On day 1, fear memory was acquired through a standard differential fear conditioning procedure. On day 2 (24h after fear acquisition), participants either underwent a stressful cold pressor test (CPT) or a control condition, 20 min before memory retrieval testing and extinction training. Possible prolonged effects of the stress manipulation were investigated on day 3 (48 h after fear acquisition), when memory retrieval and extinction were tested again. On day 2, men in the stress group showed a robust cortisol response to stress and showed lower unconditioned stimulus (US) expectancy ratings than men in the control group. This reduction in fear memory retrieval was maintained on day 3. In women, who showed a significantly smaller cortisol response to stress than men, no stress effects on fear memory retrieval were observed. No group differences were observed with respect to extinction. In conclusion, the present study provides evidence that stress can reduce memory retrieval of conditioned fear in men. Our findings may contribute to the understanding of the effects of stress and glucocorticoids on fear symptoms in anxiety disorders and suggest that such effects may be sex-specific. Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. The Evolving Role of Coliforms as Indicators of Unhygienic Processing Conditions in Dairy Foods

    Directory of Open Access Journals (Sweden)

    Nicole Helen Martin

    2016-09-01

    Full Text Available Testing for coliforms has a long history in the dairy industry and has helped to identify raw milk and dairy products that may have been exposed to unsanitary conditions. Coliform standards are included in a number of regulatory documents (e.g., the U. S. Food and Drug Administration’s Grade A Pasteurized Milk Ordinance. As a consequence, detection above a threshold of members of this method-defined, but diverse, group of bacteria can result in a wide range of regulatory outcomes. Coliforms are defined as aerobic or facultatively anaerobic, Gram negative, non-sporeforming rods capable of fermenting lactose to produce gas and acid within 48 hours at 32-35°C; 19 genera currently include at least some strains that represent coliforms. Most bacterial genera that comprise the coliform group (e.g., Escherichia, Klebsiella and Serratia are within the family Enterobacteriaceae, while at least one genus with strains recognized as coliforms, Aeromonas, is in the family Aeromonadaceae. The presence of coliforms has long been thought to indicate fecal contamination, however, recent discoveries regarding this diverse group of bacteria indicates that only a fraction are fecal in origin, while the majority are environmental contaminants. In the US dairy industry in particular, testing for coliforms as indicators of unsanitary conditions and post-processing contamination is widespread. While coliforms are easily and rapidly detected, and are not found in pasteurized dairy products that have not been exposed to post-processing contamination, advances in knowledge of bacterial populations most commonly associated with post-processing contamination in dairy foods has led to questions regarding the utility of coliforms as indicators of unsanitary conditions for dairy products. For example, Pseudomonas spp. frequently contaminate dairy products after pasteurization, yet they are not detected by coliform tests. This review will address the role that coliforms play

  13. The Evolving Role of Coliforms As Indicators of Unhygienic Processing Conditions in Dairy Foods

    Science.gov (United States)

    Martin, Nicole H.; Trmčić, Aljoša; Hsieh, Tsung-Han; Boor, Kathryn J.; Wiedmann, Martin

    2016-01-01

    Testing for coliforms has a long history in the dairy industry and has helped to identify raw milk and dairy products that may have been exposed to unsanitary conditions. Coliform standards are included in a number of regulatory documents (e.g., the U.S. Food and Drug Administration’s Grade “A” Pasteurized Milk Ordinance). As a consequence, detection above a threshold of members of this method-defined, but diverse, group of bacteria can result in a wide range of regulatory outcomes. Coliforms are defined as aerobic or facultatively anaerobic, Gram negative, non-sporeforming rods capable of fermenting lactose to produce gas and acid within 48 h at 32–35°C; 19 genera currently include at least some strains that represent coliforms. Most bacterial genera that comprise the coliform group (e.g., Escherichia, Klebsiella, and Serratia) are within the family Enterobacteriaceae, while at least one genus with strains recognized as coliforms, Aeromonas, is in the family Aeromonadaceae. The presence of coliforms has long been thought to indicate fecal contamination, however, recent discoveries regarding this diverse group of bacteria indicates that only a fraction are fecal in origin, while the majority are environmental contaminants. In the US dairy industry in particular, testing for coliforms as indicators of unsanitary conditions and post-processing contamination is widespread. While coliforms are easily and rapidly detected, and are not found in pasteurized dairy products that have not been exposed to post-processing contamination, advances in knowledge of bacterial populations most commonly associated with post-processing contamination in dairy foods has led to questions regarding the utility of coliforms as indicators of unsanitary conditions for dairy products. For example, Pseudomonas spp. frequently contaminate dairy products after pasteurization, yet they are not detected by coliform tests. This review will address the role that coliforms play in raw and

  14. Monitoring growth condition of spring maize in Northeast China using a process-based model

    Science.gov (United States)

    Wang, Peijuan; Zhou, Yuyu; Huo, Zhiguo; Han, Lijuan; Qiu, Jianxiu; Tan, Yanjng; Liu, Dan

    2018-04-01

    Early and accurate assessment of the growth condition of spring maize, a major crop in China, is important for the national food security. This study used a process-based Remote-Sensing-Photosynthesis-Yield Estimation for Crops (RS-P-YEC) model, driven by satellite-derived leaf area index and ground-based meteorological observations, to simulate net primary productivity (NPP) of spring maize in Northeast China from the first ten-day (FTD) of May to the second ten-day (STD) of August during 2001-2014. The growth condition of spring maize in 2014 in Northeast China was monitored and evaluated spatially and temporally by comparison with 5- and 13-year averages, as well as 2009 and 2013. Results showed that NPP simulated by the RS-P-YEC model, with consideration of multi-scattered radiation inside the crop canopy, could reveal the growth condition of spring maize more reasonably than the Boreal Ecosystem Productivity Simulator. Moreover, NPP outperformed other commonly used vegetation indices (e.g., Normalized Difference Vegetation Index (NDVI) and Enhanced Vegetation Index (EVI)) for monitoring and evaluating the growth condition of spring maize. Compared with the 5- and 13-year averages, the growth condition of spring maize in 2014 was worse before the STD of June and after the FTD of August, and it was better from the third ten-day (TTD) of June to the TTD of July across Northeast China. Spatially, regions with slightly worse and worse growth conditions in the STD of August 2014 were concentrated mainly in central Northeast China, and they accounted for about half of the production area of spring maize in Northeast China. This study confirms that NPP is a good indicator for monitoring and evaluating growth condition because of its capacity to reflect the physiological characteristics of crops. Meanwhile, the RS-P-YEC model, driven by remote sensing and ground-based meteorological data, is effective for monitoring crop growth condition over large areas in a near real

  15. Conceptual structure design of experimental facility for advanced spent fuel conditioning process

    International Nuclear Information System (INIS)

    Joo, J. S.; Koo, J. H.; Jung, W. M.; Jo, I. J.; Kook, D. H.; Yoo, K. S.

    2003-01-01

    A study on the advanced spent fuel conditioning process (ACP) is carring out for the effective management of spent fuels of domestic nuclear power plants. This study presents basic shielding design, modification of IMEF's reserve hot cell facility which reserved for future usage, conceptual and structural architecture design of ACP hot cell and its contents, etc. considering the characteristics of ACP. The results of this study will be used for the basic and detail design of ACP demonstration facility, and utilized as basic data for the safety evaluation as essential data for the licensing of the ACP facility

  16. Processes of Metastudy: A Study of Psychosocial Adaptation to Childhood Chronic Health Conditions

    Directory of Open Access Journals (Sweden)

    David B. Nichola

    2006-03-01

    Full Text Available Metastudy introduces a systematically aggregated interpretive portrayal of a body of literature, based on saturation and the synthesis of findings. In this metastudy, the authors examined qualitative studies addressing psychosocial adaptation to childhood chronic health conditions, published over a 30-year period (1970–2000. They describe metastudy processes, including study identification, strategies for study search and retrieval, adjudication of difference in study design and rigor, and analysis of findings. They also illustrate metastudy components through examples drawn from this project and discuss implications for practice and recommendations.

  17. Shocks induced by junctions in totally asymmetric simple exclusion processes under periodic boundary condition

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Xiaoyan, E-mail: sunxiaoyan1@gmail.com [College of Physics and Electronic Engineering, Guangxi Teacher Education University, Nanning 530001 (China); Xie, Yanbo [Department of Modern Physics, University of Science and Technology of China, Hefei 230026 (China); He, Zhiwei [College of Science, China Agricultural University, Beijing 100083 (China); Wang, Binghong [Department of Modern Physics, University of Science and Technology of China, Hefei 230026 (China)

    2011-07-11

    This Letter investigates a totally asymmetric simple exclusion process (TASEP) with junctions in a one-dimensional transport system. Parallel update rules and periodic boundary condition are adopted. Two cases corresponding to different update rules are studied. The results show that the stationary states of system mainly depend on the selection behavior of particle at the bifurcation point. -- Highlights: → For no preference case, the system exists three stationary phases. → For preference case, the system exists five stationary phases. → The road lengths have not qualitative influence on the fundamental diagram.

  18. The maximum power condition of the brayton cycle with heat exchange processes

    International Nuclear Information System (INIS)

    Jung, Pyung Suk; Cha, Jin Girl; Ro, Sung Tack

    1985-01-01

    The ideal brayton cycle has been analyzed with the heat exchange processes between the working fluid and the heat source and the sink while their heat capacity rates are constant. The power of the cycle can be expressed in terms of a temperature of the cycle and the heat capacity rate of the working fluid. There exists an optimum power condition where the heat capacity rate of the working fluid has a value between those of the heat source and the heat sink, and the cycle efficiency is determined by the inlet temperatures of the heat source and the sink. (Author)

  19. The effect of austenitizing conditions in the ductile iron hardening process on longitudinal ultrasonic wave velocity

    Directory of Open Access Journals (Sweden)

    A. W. Orłowicz

    2014-04-01

    Full Text Available The paper presents results of a research on the effect of austenitizing temperature and time adopted in the hardening operation on the ultrasonic wave velocity in ductile iron. It has been found that with increasing austenitizing temperature and with the passage of the austenitizing time, a monotonic decrease of the ultrasonic longitudinal wave velocity value occurred. Implementation of ultrasonic testing of results obtained in the course of the cast iron hardening process both in production and as-cast conditions, requires development of a test methodology that must take into account the influence of base material structure (degree of nodularization, graphite precipitation count on the ultrasound wave velocity.

  20. The Operator's Diagnosis Task under Abnormal Operating Conditions in Industrial Process Plant

    DEFF Research Database (Denmark)

    Goodstein, L.P.; Pedersen, O.M.; Rasmussen, Jens

    1974-01-01

    Analysis of serious accidents in connection with the operation of technical installations demonstrate that the diagnosis task which confronts personnel under non-normal plant conditions is a critical one. This report presents a preliminary outline of characteristic traits connected with the task...... of diagnosis for use in discussions of (a) the studies which are necessary in order to formulate the operator's diagnostic procedures and (b) the possibilities which exists for supporting these procedures through appropriate data processing and display in the control system. At the same time, attempts are made...

  1. Working Conditions, Occupational Injuries, and Health Among Filipino Fish Processing Workers in Dutch Harbor, Alaska.

    Science.gov (United States)

    Garcia, Gabriel Macasiray; de Castro, Butch

    2017-05-01

    This study explored how unique environmental conditions in Alaska influenced occupational health and safety for Filipino fish processing workers, many of whom migrated from warm locations (e.g., the Philippines, California, and Nevada). In-depth interviews were conducted with 26 Filipino workers in one commercial fish processing company in Dutch Harbor. Results indicated that cold weather interferes with workers' job performance, increasing their risk for injury and illness, whereas the community's isolation and rural nature causes loneliness and boredom, resulting in more high-risk behaviors. Other non-environmental factors affecting worker health include roommate and supervisor concerns and culture-specific practices. Findings suggest the importance of job rotation to avoid long exposures to cold temperatures, the value of a designated individual to inform workers about company and community resources that promote healthy lifestyles, and the possible utility of a joint worker-management safety committee.

  2. Experimental Investigation into Suitable Process Conditions for Plastic Injection Molding of Thin-Sheet Parts

    Directory of Open Access Journals (Sweden)

    Dyi-Cheng Chen

    2014-04-01

    Full Text Available This study performs an experimental investigation into the effects of the process parameters on the surface quality of injection molded thin-sheet thermoplastic components. The investigations focus specifically on the shape, number and position of the mold gates, the injection pressure and the injection rate. It can be seen that the gravity force entering point improved filling of the cavity for the same forming time and injection pressure. Moreover, it shows the same injection pressure and packing time, the taper-shape gate yields a better surface appearance than the sheet-shape gate. The experimental results provide a useful source of reference in suitable the process conditions for the injection molding of thin-sheet plastic components.

  3. Spent nuclear fuel project cold vacuum drying facility process water conditioning system design description

    International Nuclear Information System (INIS)

    IRWIN, J.J.

    1998-01-01

    This document provides the System Design Description (SDD) for the Cold Vacuum Drying Facility (CVDF) Process Water Conditioning (PWC) System. The SDD was developed in conjunction with HNF-SD-SNF-SAR-002, Safety Analysis Report for the Cold Vacuum Drying Facility, Phase 2, Supporting Installation of Processing Systems (Garvin 1998), the HNF-SD-SNF-DRD-O02, 1998, Cold Vacuum Drying Facility Design Requirements, and the CVDF Design Summary Report. The SDD contains general descriptions of the PWC equipment, the system functions, requirements and interfaces. The SDD provides references for design and fabrication details, operation sequences and maintenance. This SDD has been developed for the SNFP Operations Organization and shall be updated, expanded, and revised in accordance with future design, construction and startup phases of the CVDF until the CVDF final ORR is approved

  4. The orexin component of fasting triggers memory processes underlying conditioned food selection in the rat.

    Science.gov (United States)

    Ferry, Barbara; Duchamp-Viret, Patricia

    2014-03-14

    To test the selectivity of the orexin A (OXA) system in olfactory sensitivity, the present study compared the effects of fasting and of central infusion of OXA on the memory processes underlying odor-malaise association during the conditioned odor aversion (COA) paradigm. Animals implanted with a cannula in the left ventricle received ICV infusion of OXA or artificial cerebrospinal fluid (ACSF) 1 h before COA acquisition. An additional group of intact rats were food-deprived for 24 h before acquisition. Results showed that the increased olfactory sensitivity induced by fasting and by OXA infusion was accompanied by enhanced COA performance. The present results suggest that fasting-induced central OXA release influenced COA learning by increasing not only olfactory sensitivity, but also the memory processes underlying the odor-malaise association.

  5. Forensic Stable Isotope Biogeochemistry

    Science.gov (United States)

    Cerling, Thure E.; Barnette, Janet E.; Bowen, Gabriel J.; Chesson, Lesley A.; Ehleringer, James R.; Remien, Christopher H.; Shea, Patrick; Tipple, Brett J.; West, Jason B.

    2016-06-01

    Stable isotopes are being used for forensic science studies, with applications to both natural and manufactured products. In this review we discuss how scientific evidence can be used in the legal context and where the scientific progress of hypothesis revisions can be in tension with the legal expectations of widely used methods for measurements. Although this review is written in the context of US law, many of the considerations of scientific reproducibility and acceptance of relevant scientific data span other legal systems that might apply different legal principles and therefore reach different conclusions. Stable isotopes are used in legal situations for comparing samples for authenticity or evidentiary considerations, in understanding trade patterns of illegal materials, and in understanding the origins of unknown decedents. Isotope evidence is particularly useful when considered in the broad framework of physiochemical processes and in recognizing regional to global patterns found in many materials, including foods and food products, drugs, and humans. Stable isotopes considered in the larger spatial context add an important dimension to forensic science.

  6. Optimization of Electrochemical Treatment Process Conditions for Distillery Effluent Using Response Surface Methodology

    Directory of Open Access Journals (Sweden)

    P. Arulmathi

    2015-01-01

    Full Text Available Distillery industry is recognized as one of the most polluting industries in India with a large amount of annual effluent production. In this present study, the optimization of electrochemical treatment process variables was reported to treat the color and COD of distillery spent wash using Ti/Pt as an anode in a batch mode. Process variables such as pH, current density, electrolysis time, and electrolyte dose were selected as operation variables and chemical oxygen demand (COD and color removal efficiency were considered as response variable for optimization using response surface methodology. Indirect electrochemical-oxidation process variables were optimized using Box-Behnken response surface design (BBD. The results showed that electrochemical treatment process effectively removed the COD (89.5% and color (95.1% of the distillery industry spent wash under the optimum conditions: pH of 4.12, current density of 25.02 mA/cm2, electrolysis time of 103.27 min, and electrolyte (NaCl concentration of 1.67 g/L, respectively.

  7. Conditioning matrices from high level waste resulting from pyrochemical processing in fluorine salt

    International Nuclear Information System (INIS)

    Grandjean, Agnes; Advocat, Thierry; Bousquet, Nicolas; Jegou, Christophe

    2007-01-01

    Separating the actinides from the fission products through reductive extraction by aluminium in a LiF/AlF 3 medium is a process investigated for pyrometallurgical reprocessing of spent fuel. The process involves separation by reductive salt-metal extraction. After dissolving the fuel or the transmutation target in a salt bath, the noble metal fission products are first extracted by contacting them with a slightly reducing metal. After extracting the metal fission products, then the actinides are selectively separated from the remaining fission products. In this hypothesis, all the unrecoverable fission products would be conditioned as fluorides. Therefore, this process will generate first a metallic waste containing the 'reducible' fission products (Pd, Mo, Ru, Rh, Tc, etc.) and a fluorine waste containing alkali-metal, alkaline-earth and rare earth fission products. Immobilization of these wastes in classical borosilicate glasses is not feasible due to the very low solubility of noble metals, and of fluoride in these hosts. Alternative candidates have therefore been developed including silicate glass/ceramic system for fluoride fission products and metallic ones for noble metal fission products. These waste-forms were evaluated for their confinement properties like homogeneity, waste loading, volatility during the elaboration process, chemical durability, etc. using appropriate techniques. (authors)

  8. Processing of masked and unmasked emotional faces under different attentional conditions: an electrophysiological investigation.

    Directory of Open Access Journals (Sweden)

    Marzia eDel Zotto

    2015-10-01

    Full Text Available In order to investigate the interactions between non-spatial selective attention, awareness and emotion processing, we carried out an ERP study using a backward masking paradigm, in which angry, fearful, happy and neutral facial expressions were presented, while participants attempted to detect the presence of one or the other category of facial expressions in the different experimental blocks. ERP results showed that negative emotions enhanced an early N170 response over temporal-occipital leads in both masked and unmasked conditions, independently of selective attention. A later effect arising at the P2 was linked to awareness. Finally, selective attention was found to affect the N2 and N3 components over occipito-parietal leads. Our findings reveal that i the initial processing of facial expressions arises prior to attention and awareness; ii attention and awareness give rise to temporally distinct periods of activation independently of the type of emotion with only a partial degree of overlap; and iii selective attention appears to be influenced by the emotional nature of the stimuli, which in turn impinges on unconscious processing at a very early stage. This study confirms previous reports that negative facial expressions can be processed rapidly, in absence of visual awareness and independently of selective attention. On the other hand, attention and awareness may operate in a synergistic way, depending on task demand.

  9. A Big Spatial Data Processing Framework Applying to National Geographic Conditions Monitoring

    Directory of Open Access Journals (Sweden)

    F. Xiao

    2018-04-01

    Full Text Available In this paper, a novel framework for spatial data processing is proposed, which apply to National Geographic Conditions Monitoring project of China. It includes 4 layers: spatial data storage, spatial RDDs, spatial operations, and spatial query language. The spatial data storage layer uses HDFS to store large size of spatial vector/raster data in the distributed cluster. The spatial RDDs are the abstract logical dataset of spatial data types, and can be transferred to the spark cluster to conduct spark transformations and actions. The spatial operations layer is a series of processing on spatial RDDs, such as range query, k nearest neighbor and spatial join. The spatial query language is a user-friendly interface which provide people not familiar with Spark with a comfortable way to operation the spatial operation. Compared with other spatial frameworks, it is highlighted that comprehensive technologies are referred for big spatial data processing. Extensive experiments on real datasets show that the framework achieves better performance than traditional process methods.

  10. Torrefaction of oil palm frond: The effect of process condition to calorific value and proximate analysis

    Science.gov (United States)

    Susanty, W.; Helwani, Z.; Zulfansyah

    2018-04-01

    Oil palm frond can be used as alternative energy source by torrefaction process. Torrefaction is a treatment process of biomass into solid fuel by heating within temperature range of 200-300°C in an inert environment. This research aims to result solid fuel through torrefaction and to study the effect of process variable interaction. Torrefaction of oil palm frond was using fixed bed horizontal reactor with operation condition of temperature (225-275 °C), time (15-45 minutes) and nitrogen flow rate (50-150 ml/min). Responses resulted were calorific value and proximate (moisture, ash, volatile matter and fixed carbon). Analysis result was processed by using Design Expert v7.0.0. Result obtained for calorific value was 17.700-19.600 kJ/kg and for the proximate were moisture range of 3-4%; ash range of 1.5-4%; volatile matter of 45-55% and fixed carbon of 37-46%. The most affecting factor signficantly towards the responses was temperature then followed by time and nitrogen flow rate.

  11. A Big Spatial Data Processing Framework Applying to National Geographic Conditions Monitoring

    Science.gov (United States)

    Xiao, F.

    2018-04-01

    In this paper, a novel framework for spatial data processing is proposed, which apply to National Geographic Conditions Monitoring project of China. It includes 4 layers: spatial data storage, spatial RDDs, spatial operations, and spatial query language. The spatial data storage layer uses HDFS to store large size of spatial vector/raster data in the distributed cluster. The spatial RDDs are the abstract logical dataset of spatial data types, and can be transferred to the spark cluster to conduct spark transformations and actions. The spatial operations layer is a series of processing on spatial RDDs, such as range query, k nearest neighbor and spatial join. The spatial query language is a user-friendly interface which provide people not familiar with Spark with a comfortable way to operation the spatial operation. Compared with other spatial frameworks, it is highlighted that comprehensive technologies are referred for big spatial data processing. Extensive experiments on real datasets show that the framework achieves better performance than traditional process methods.

  12. Plasma processing conditions substantially influence circulating microRNA biomarker levels.

    Science.gov (United States)

    Cheng, Heather H; Yi, Hye Son; Kim, Yeonju; Kroh, Evan M; Chien, Jason W; Eaton, Keith D; Goodman, Marc T; Tait, Jonathan F; Tewari, Muneesh; Pritchard, Colin C

    2013-01-01

    Circulating, cell-free microRNAs (miRNAs) are promising candidate biomarkers, but optimal conditions for processing blood specimens for miRNA measurement remain to be established. Our previous work showed that the majority of plasma miRNAs are likely blood cell-derived. In the course of profiling lung cancer cases versus healthy controls, we observed a broad increase in circulating miRNA levels in cases compared to controls and that higher miRNA expression correlated with higher platelet and particle counts. We therefore hypothesized that the quantity of residual platelets and microparticles remaining after plasma processing might impact miRNA measurements. To systematically investigate this, we subjected matched plasma from healthy individuals to stepwise processing with differential centrifugation and 0.22 µm filtration and performed miRNA profiling. We found a major effect on circulating miRNAs, with the majority (72%) of detectable miRNAs substantially affected by processing alone. Specifically, 10% of miRNAs showed 4-30x variation, 46% showed 30-1,000x variation, and 15% showed >1,000x variation in expression solely from processing. This was predominantly due to platelet contamination, which persisted despite using standard laboratory protocols. Importantly, we show that platelet contamination in archived samples could largely be eliminated by additional centrifugation, even in frozen samples stored for six years. To minimize confounding effects in microRNA biomarker studies, additional steps to limit platelet contamination for circulating miRNA biomarker studies are necessary. We provide specific practical recommendations to help minimize confounding variation attributable to plasma processing and platelet contamination.

  13. In Situ Visualization of the Phase Behavior of Oil Samples Under Refinery Process Conditions.

    Science.gov (United States)

    Laborde-Boutet, Cedric; McCaffrey, William C

    2017-02-21

    To help address production issues in refineries caused by the fouling of process units and lines, we have developed a setup as well as a method to visualize the behavior of petroleum samples under process conditions. The experimental setup relies on a custom-built micro-reactor fitted with a sapphire window at the bottom, which is placed over the objective of an inverted microscope equipped with a cross-polarizer module. Using reflection microscopy enables the visualization of opaque samples, such as petroleum vacuum residues, or asphaltenes. The combination of the sapphire window from the micro-reactor with the cross-polarizer module of the microscope on the light path allows high-contrast imaging of isotropic and anisotropic media. While observations are carried out, the micro-reactor can be heated to the temperature range of cracking reactions (up to 450 °C), can be subjected to H2 pressure relevant to hydroconversion reactions (up to 16 MPa), and can stir the sample by magnetic coupling. Observations are typically carried out by taking snapshots of the sample under cross-polarized light at regular time intervals. Image analyses may not only provide information on the temperature, pressure, and reactive conditions yielding phase separation, but may also give an estimate of the evolution of the chemical (absorption/reflection spectra) and physical (refractive index) properties of the sample before the onset of phase separation.

  14. Optimum Condition for Plutonium Electrodeposition Process in Radiochemistry and Environment Laboratory, Nuclear Malaysia

    International Nuclear Information System (INIS)

    Yii, Mei-Wo; Abdullah Siddiqi Ismail

    2014-01-01

    Determination of alpha emitting plutonium radionuclides such as Pu-238, Pu-239 and Pu-240 concentrations inside a sample require lots of radiochemistry purification process to separate them from other interfering alpha emitters. These pure isotopes are then been electrodeposited onto a stainless steel disc and quantified using alpha spectrometry counter. In Radiochemistry and Environment Laboratory (RAS), Nuclear Malaysia, the quantification is done by comparing these isotopes with the recovery of known amount plutonium tracer, Pu-242, that been added into the sample prior analysis. This study been conducted to find the optimum conditions for the electrolysis process used at RAS. Four variable parameters that may interfere the percentage recovery of tracer hence the current, cathode to anode distance, pH and electrolysis duration had been identify and studied. Study was carry out using Pu-242 standard solution and the deposition disc was counted using Zinc Sulphite (silver) counter. Studies outcome suggested that the optimum conditions to reduce plutonium ion happens at 1-1.1 ampere of current, 3-5 mm of electrodes distance, pH 2.2-2.5 and a minimal electrolysis duration of 2 hours. (author)

  15. Optimal periodic inspection of a deterioration process with sequential condition states

    International Nuclear Information System (INIS)

    Kallen, M.J.; Noortwijk, J.M. van

    2006-01-01

    The condition of components subject to visual inspections is often evaluated on a discrete scale. If at each inspection a decision is made to do nothing or to perform preventive or corrective maintenance, the proposed decision model allows us to determine the optimal time between periodic inspections, such that the expected average costs per unit of time are minimized. The model which describes the uncertain condition over time is based on a Markov process with sequential phases. The key quantities involved in the model are the probabilities of having to perform either preventive or corrective maintenance before or after an inspection. The costs functions for two scenarios are presented: a scenario in which failure is immediately detected without the need to perform an inspection and a scenario in which failure is only detected by inspection of the object. Analytical results for a special case and algorithmic results for a broad class of Markov processes are derived. The model is illustrated using an application to the periodic inspection of road bridges

  16. Optimal condition for fabricating superhydrophobic Aluminum surfaces with controlled anodizing processes

    Science.gov (United States)

    Saffari, Hamid; Sohrabi, Beheshteh; Noori, Mohammad Reza; Bahrami, Hamid Reza Talesh

    2018-03-01

    A single step anodizing process is used to produce micro-nano structures on Aluminum (1050) substrates with sulfuric acid as electrolyte. Therefore, surface energy of the anodized layer is reduced using stearic acid modification. Undoubtedly, effects of different parameters including anodizing time, electrical current, and type and concentration of electrolyte on the final contact angle are systemically studied and optimized. Results show that anodizing current of 0.41 A, electrolyte (sulfuric acid) concentration of 15 wt.% and anodizing time of 90 min are optimal conditions which give contact angle as high as 159.2° and sliding angle lower than 5°. Moreover, the study reveals that adding oxalic acid to the sulfuric acid cannot enhance superhydrophobicity of the samples. Also, scanning electron microscopy images of samples show that irregular (bird's nest) structures present on the surface instead of high-ordered honeycomb structures expecting from normal anodizing process. Additionally, X-ray diffraction analysis of the samples shows that only amorphous structures present on the surface. The Brunauer-Emmett-Teller (BET) specific surface area of the anodized layer is 2.55 m2 g-1 in optimal condition. Ultimately, the surface keeps its hydrophobicity in air and deionized water (DIW) after one week and 12 weeks, respectively.

  17. Effect of inlet and outlet flow conditions on natural gas parameters in supersonic separation process.

    Directory of Open Access Journals (Sweden)

    Yan Yang

    Full Text Available A supersonic separator has been introduced to remove water vapour from natural gas. The mechanisms of the upstream and downstream influences are not well understood for various flow conditions from the wellhead and the back pipelines. We used a computational model to investigate the effect of the inlet and outlet flow conditions on the supersonic separation process. We found that the shock wave was sensitive to the inlet or back pressure compared to the inlet temperature. The shock position shifted forward with a higher inlet or back pressure. It indicated that an increasing inlet pressure declined the pressure recovery capacity. Furthermore, the shock wave moved out of the diffuser when the ratio of the back pressure to the inlet one was greater than 0.75, in which the state of the low pressure and temperature was destroyed, resulting in the re-evaporation of the condensed liquids. Natural gas would be the subsonic flows in the whole supersonic separator, if the mass flow rate was less than the design value, and it could not reach the low pressure and temperature for the condensation and separation of the water vapor. These results suggested a guidance mechanism for natural gas supersonic separation in various flow conditions.

  18. Simulate speleogenesis processes with an approach based on fracturing and hydrogeological processes: effect of various hydraulic boundary conditions

    Science.gov (United States)

    Lafare, A.; Jourde, H.; Leonardi, V.; Pistre, S.; Dörfliger, N.

    2012-04-01

    Several numerical modeling approaches attempted to simulate the processes of karst conduit genesis. These existing methods are mainly based on the physical and chemical laws driving the carbonate dissolution processes (taking account of calcite saturation of the water and the partial pressure of carbon dioxide). As a consequence, these works bring a well-documented knowledge on the kinetics of the carbonate dissolution processes in karst systems. Nevertheless, these models are mainly applied on simplified initial void networks, which do not match the fracturing and geological reality. Considering that the initial geometry of the void network (fractures, bedding planes) would have an influence on the final pattern of the speleological network, taking account of it could improve the understanding of speleogenesis. In the aim to take into account the geometry of the initial void network (fracture networks of several orders), a numerical model is developed, which involves a pseudo-statistic fracturing generator (REZO3D, Jourde 1999, Josnin et al. 2002, Jourde et al. 2002) coupled to a finite element groundwater simulator (GROUNDWATER, F. Cornaton, CHYN, University of Neuchâtel). The principle of the modeling of the genesis of the karst drainage system is based on an analogical empirical polynomial equation considering the pore velocity and the mean age of the water as main parameters. The computation is carried out on the basis of a time step, whose duration depends on the simulated scenario (from 100 to 5000 years). The mean age of the water is used in order to simulate the decrease of the chemical dissolving potential of the water within the aquifer, in contact with the carbonate rock. The first simulator -REZO3D- allows producing three-dimensional discrete fracture networks constituted by plane fractures, whose spatial distribution respects mechanical and statistical laws. These networks are then processed in order to write finite element meshes which constitute

  19. Use of a ring-shaped, passively stable, superconducting magnetic bearing in the ring spinning process; Einsatz eines ringfoermigen, passiv stabilen, supraleitenden Magnetlagers im Ringspinnprozess

    Energy Technology Data Exchange (ETDEWEB)

    Berger, Anne; Sparing, Maria; Berger, Dietmar; Fuchs, Guenter; Schultz, Ludwig [IFW Dresden (Germany). Inst. fuer Metallische Werkstoffe; Hossain, Mahmud; Abdkader, Anwar; Cherif, Chokri [TU Dresden (Germany). ITM

    2015-07-01

    For the integration of a superconducting magnetic bearing in a ring spinning machine a LN{sub 2} continuous flow cryostat was developed, which is needed to cool the superconductor below its transition temperature of ∝91 K and simultaneously ensures that the spinning process takes place at room temperature. The ring spinning process is the most widely used process for spinning yarn. In this case, a loose fiber connection is first stretched in a roller system, then twisted by the so-called spinning ring-ring traveler system, and finally wound on a spindle. The spinning ring is a circular guide, which is mounted around the spindle. On this the ring traveler rotates as yarn guide. The yarn is driven by the rotation of the spindle and there is a balloon-shaped movement of the yarn which results the twist. The productivity of the process is limited by the systematic frictional heat between the yarn, spinning ring and ring travelers. This leads at high speeds to yarn breakage and limits the maximum spindle speed depending on the type of fiber to a maximum of 25,000 U/min. To increase the speed and thus the productivity of the process, the conventional spinning ring-ring rotor system is replaced by a superconducting magnetic bearing. Here floats a NdFeB permanent magnet passively stable over the LN{sub 2} cooled ceramic high-temperature superconductor YBa{sub 2}Cu{sub 3}O{sub 7-x}. Driven by the yarn the permanent magnet rotates, thus ensuring the necessary balloon-shaped yarn movement to twist. Such a bearing has been successfully tested in a ring spinning machine. Preliminary results show a similar yarn quality. [German] Fuer die Integration eines supraleitenden Magnetlagers in eine Ringspinnmaschine wurde ein LN{sub 2}-Durchflusskryostat entwickelt, der noetig ist, um den Supraleiter unter seine Sprungtemperatur von ∝91 K zu kuehlen und gleichzeitig dafuer sorgt, dass der Spinnprozess bei Raumtemperatur ablaeuft. Der Ringspinnprozess ist der am weitesten verbreitete

  20. Design, development and test of the gearbox condition monitoring system using sound signal processing

    Directory of Open Access Journals (Sweden)

    M Zamani

    2016-09-01

    format and MATLAB R2014a software used for data processing. Data processing: Signal processing method in the frequency domain is used in order to reveal the defects. Fast Fourier Transform: Fast Fourier Transform FFT for application in electronic equipment specially analyzers have great importance. In this condition, sampling number is chosen exponentially as 2N which decreases the calculation volume significantly. Determination of defect kind of gearwheel using frequency spectrum analysis: In mentioned gearwheel, errors were generated synthetically. Defect kind of these errors was generated in separate gearwheels in order to investigate the defects more precisely and a gearwheel was considered as control gearwheel. Despite of this, the sound of all of the gearwheels in correct condition was stored. Results and Discussion Comparison of processed acoustic signals from gearwheels of gearbox in two correct and incorrect conditions was indicative of gearwheel involvement, frequency, their harmony and the changes resulted from defects. Gearwheel defect detection tests showed that at the speeds of 1496, 1050 and 749 rpm, investigated defects are recognizable with a comparison of the frequency spectrum of obtained signals in correct and incorrect conditions and according to the involvement frequency of gearwheel, its harmony and sided spectrum. Results of the frequency spectrum of signal analysis in speed of 1496 rpm pinion showed the defect of one tooth fracture in involvement frequency of gearwheels by 489, 350 and 249 Hz respectively which became apparent with a mentioned frequency domain increment. A worn tooth defect in a gearwheel was completely determinable as sided bands with equal distance around gearwheel involvement frequency in the signal frequency determination of the speeds of 1496 and 105 rpm pinion, but became a bit harder in less speeds. Investigation of frequency spectrum of acoustic signal resulted from gearwheel, is indicative of the ability of this method

  1. [CO2 response process and its simulation of Prunus sibirica photosynthesis under different soil moisture conditions].

    Science.gov (United States)

    Wu, Qin; Zhang, Guang-Can; Pei, Bin; Xu, Zhi-Qiang; Zhao, Yu; Fang, Li-Dong

    2013-06-01

    Taking the two-year old potted Prunus sibirica seedlings as test materials, and using CIRAS-2 photosynthetic system, this paper studied the CO2 response process of P. sibirica photosynthesis in semi-arid loess hilly region under eight soil moisture conditions. The CO2 response data of P. sibirica were fitted and analyzed by rectangular hyperbola model, exponential equation, and modified rectangular hyperbola model. Meanwhile, the quantitative relationships between the photosynthesis and the soil moisture were discussed. The results showed that the CO2 response process of P. sibirica photosynthesis had obvious response characteristics to the soil moisture threshold. The relative soil water content (RWC) required to maintain the higher photosynthetic rate (P(n)) and carboxylation efficiency (CE) of P. sibirica was in the range of 46.3%-81.9%. In this RWC range, the photosynthesis did not appear obvious CO2 saturated inhibition phenomenon. When the RWC exceeded this range, the photosynthetic capacity (P(n max)), CE, and CO2 saturation point (CSP) decreased evidently. Under different soil moisture conditions, there existed obvious differences among the three models in simulating the CO2 response data of P. sibirica. When the RWC was in the range of 46.3%-81.9%, the CO2 response process and the characteristic parameters such as CE, CO2 compensation point (see symbol), and photorespiration rate (R(p)) could be well fitted by the three models, and the accuracy was in the order of modified rectangular hyperbola model > exponential equation > rectangular hyperbola model. When the RWC was too high or too low, namely, the RWC was > 81.9% or CO2 response process and the characteristic parameters. It was suggested that when the RWC was from 46.3% to 81.9%, the photosynthetic efficiency of P. sibirica was higher, and, as compared with rectangular hyperbola model and exponential equation, modified rectangular hyperbola model had more applicability to fit the CO2 response data of

  2. Retrofit of heat exchanger networks with pressure recovery of process streams at sub-ambient conditions

    International Nuclear Information System (INIS)

    Onishi, Viviani C.; Ravagnani, Mauro A.S.S.; Caballero, José A.

    2015-01-01

    Highlights: • New mathematical model for heat exchanger networks retrofit with pressure recovery. • Optimal heat and work integration applied to the retrofit of sub-ambient processes. • Streams pressure manipulation is used to enhance heat integration of the system. • Compressors and turbines can act on a coupling shaft and/or as stand-alone equipment. • Use of smaller amount of cold utilities, reducing significantly the operational costs. - Abstract: This paper presents a new mathematical programming model for the retrofit of heat exchanger networks (HENs), wherein the pressure recovery of process streams is conducted to enhance heat integration. Particularly applied to cryogenic processes, HENs retrofit with combined heat and work integration is mainly aimed at reducing the use of expensive cold services. The proposed multi-stage superstructure allows the increment of the existing heat transfer area, as well as the use of new equipment for both heat exchange and pressure manipulation. The pressure recovery of streams is carried out simultaneously with the HEN design, such that the process conditions (streams pressure and temperature) are variables of optimization. The mathematical model is formulated using generalized disjunctive programming (GDP) and is optimized via mixed-integer nonlinear programming (MINLP), through the minimization of the retrofit total annualized cost, considering the turbine and compressor coupling with a helper motor. Three case studies are performed to assess the accuracy of the developed approach, including a real industrial example related to liquefied natural gas (LNG) production. The results show that the pressure recovery of streams is efficient for energy savings and, consequently, for decreasing the HEN retrofit total cost especially in sub-ambient processes

  3. Influence of postharvest processing and storage conditions on key antioxidants in pūhā (Sonchus oleraceus L.)

    DEFF Research Database (Denmark)

    Ou, Zong-Quan; Schmierer, David M; Strachan, Clare J

    2014-01-01

    To investigate effects of different postharvest drying processes and storage conditions on key antioxidants in Sonchus oleraceus L. leaves.......To investigate effects of different postharvest drying processes and storage conditions on key antioxidants in Sonchus oleraceus L. leaves....

  4. Safety evaluation report of hot cell facilities for demonstration of advanced spent fuel conditioning process

    International Nuclear Information System (INIS)

    You, Gil Sung; Choung, W. M.; Ku, J. H.; Cho, I. J.; Kook, D. H.; Park, S. W.; Bek, S. Y.; Lee, E. P.

    2004-10-01

    The advanced spent fuel conditioning process(ACP) proposed to reduce the overall volume of the PWR spent fuel and improve safety and economy of the long-term storage of spent fuel. In the next phase(2004∼2006), the hot test will be carried out for verification of the ACP in a laboratory scale. For the hot test, the hot cell facilities of α- type and auxiliary facilities are required essentially for safe handling of high radioactive materials. As the hot cell facilities for demonstration of the ACP, a existing hot cell of β- type will be refurbished to minimize construction expenditures of hot cell facility. Up to now, the detail design of hot cell facilities and process were completed, and the safety analysis was performed to substantiate secure of conservative safety. The design data were submitted for licensing which was necessary for construction and operation of hot cell facilities. The safety investigation of KINS on hot cell facilities was completed, and the license for construction and operation of hot cell facilities was acquired already from MOST. In this report, the safety analysis report submitted to KINS was summarized. And also, the questionnaires issued from KINS and answers of KAERI in process of safety investigation were described in detail

  5. Performance Evaluation of the Neutron Coincidence Counter for the Advanced Spent Fuel Conditioning Process

    International Nuclear Information System (INIS)

    Lee, S.Y.; Li, T.K.; Menlove, Howard O.; Kim, H.D.; Ko, W.I.; Park, S.W.

    2005-01-01

    The Advanced Spent Fuel Conditioning Process (ACP) is a pyrochemical dry reprocessing technique to convert oxide-type spent nuclear fuel into a metallic form. The Korea Atomic Energy Research Institute (KAERI) has been developing this technology for the purpose of spent fuel management and is planning to perform a lab-scale demonstration in 2006. With this technology, a significant reduction of the volume and heat load of spent fuel is expected, which could decrease the burden of safety and economics. In this study, MCNPX code calculations were carried out to estimate the performance of a neutron coincidence counter designed for measruement of the process materials in the pilot-scale ACP facility. To verify the design requirement, the singles and doubles counting rates of the detectors were simulated with the latest coincidence capability of the MCNPX code. Then, the precision of the coincidence measurements were evaluated on various process materials from the ACP. It was verified that the performance of the neutron coincidence counter could meet the design criteria for all samples in the ACP, and the material accounting system for the pilot-scale ACP facility could meet the IAEA safeguards goals.

  6. Sensory reactivity, empathizing and systemizing in autism spectrum conditions and sensory processing disorder

    Directory of Open Access Journals (Sweden)

    Teresa Tavassoli

    2018-01-01

    Full Text Available Although the DSM-5 added sensory symptoms as a criterion for ASC, there is a group of children who display sensory symptoms but do not have ASC; children with sensory processing disorder (SPD. To be able to differentiate these two disorders, our aim was to evaluate whether children with ASC show more sensory symptomatology and/or different cognitive styles in empathy and systemizing compared to children with SPD and typically developing (TD children. The study included 210 participants: 68 children with ASC, 79 with SPD and 63 TD children. The Sensory Processing Scale Inventory was used to measure sensory symptoms, the Autism Spectrum Quotient (AQ to measure autistic traits, and the Empathy Quotient (EQ and Systemizing Quotient (SQ to measure cognitive styles. Across groups, a greater sensory symptomatology was associated with lower empathy. Further, both the ASC and SPD groups showed more sensory symptoms than TD children. Children with ASC and SPD only differed on sensory under-reactivity. The ASD group did, however, show lower empathy and higher systemizing scores than the SPD group. Together, this suggest that sensory symptoms alone may not be adequate to differentiate children with ASC and SPD but that cognitive style measures could be used for differential diagnosis. Keywords: Autism spectrum conditions, Sensory processing disorder, Sensory symptoms, Empathy, Systemizing

  7. Analysis of the kinetics of decohesion process in the conditions of cyclic temperature variations

    International Nuclear Information System (INIS)

    Zuchowski, R.

    1981-01-01

    Specimens made of four types of heat-resistant steels were used in the investigation. Various variants of loading process were applied, resulting in thermal fatigue, cyclic creep and isothermal fatigue. Stress or strain variation as well as intensity of acoustic emission were recorded during the tests as a function of time. Cyclic variations of strain or stress amplitude were found to occur one full period covering few to several cycles. Comparing the relative number of acoustic emission impulses with the variation of stress or strain leads to the conclusion that cyclic character of strain or stress variation results from cyclic character of damage cumulation process. This statement is confirmed by the results of material damage degree determination based on specific strain work measurements. Results of investigation testify to the equivalence of action (in terms of energy) of cyclically variable force field at constant temperature and of constant force field in the conditions of cyclic temperature variations. Damage mechanism can be different in each case, because it depends (for a given material) on loading process parameters and in particular - on temperature and stress value. (orig./HP)

  8. Optimal control of the process of cultivation in the conditions of infection

    Directory of Open Access Journals (Sweden)

    N. V. Sukhanova

    2016-01-01

    Full Text Available The article presents a way of solving of the optimal control problem of antibiotic feeding under condition of infection, consisting in the selection of the optimal control in the field of admissible control, with the aim of achieving a compromise between the losses in production due to the presence of foreign microflora, and the cost of its suppression due to the application of antibiotic. The presence of other microorganisms in the finished product, in particular of the “wild“ ones, considerably impairs the quality indicators of the final product (in particular, it reduces the storage time. In peculiar conditions of production it is possible to improve the quality of target product due to elimination of infection, including, when used antibiotics in the process of cultivation, but due to the lack of efficient algorithms and control systems of their supply the question is still open. We use the system of Lotka-Volterra adapted for microbiological process as a mathematical model adequately describing the situation of competitive interaction of two populations of microorganisms (useful and “wild“ ones due to the consumption of one resource. The aim is to find a control law U(t belonging to the field of admissible control. The control that affords minimum to the optimization criterion in accordance with the principle of maximum is defined by the condition of the maximum of Hamilton function and the resulting canonical system of equations. The modified conjugated system of equations in matrix form is obtained. The solution of system of differential-different equations in the analytical form is found using the method of coordinate transformation. As a result an optimal control law is found (with regard to the selected criterion. This is the control law of application of the antibiotic, allowing to control the concentration of foreign microflora in the process of cultivation of microorganisms and accounting for the specific

  9. Production and processing of fuel by the forest industry - opportunities and conditions

    International Nuclear Information System (INIS)

    Magnusson, L.

    1991-01-01

    The purpose of this study was to illustrate the opportunities for the forest industry to establish a system of handling and processing biofuels in conjunction with their existing activities, and which would supply a future market for biofuels in, for example, electricity generation. The sawmills report that it is difficult today to find a market for fuel products, especially for sawmills at greater distances from larger biofuel-consuming plants. The sawmills show great interest in cogeneration in their own plants, but report difficulties in achieving profitability. The main problem is reported to be that the price of the surplus electricity delivered to the grid is too low, but also that the electricity prices today are so low that it is difficult to justify even generating electricity for the mill's own use. There is an interest in the paper and pulp industry for integrated methods and production of biofuels since the part-tree methods used, at least in some parts of Sweden, are considered to contribute also to an increase in the availability of pulp wood to the industry. A fundamental viewpoint is, however, that the plants are built for the primary purpose of producing pulp or paper. It is unlikely that the industry would give priority to investments for production of a new secondary product in the form of fuel products, particularly when the conditions today imply that there are few possibilities to achieve any particular profitability. The most probable solution is that the fuel is processed outside the industry by other parties, e.g., the forest divisions. In the long term, increased efficiency in the processes may lead to a primary heat surplus which could be used to produce processed fuels

  10. Stable convergence and stable limit theorems

    CERN Document Server

    Häusler, Erich

    2015-01-01

    The authors present a concise but complete exposition of the mathematical theory of stable convergence and give various applications in different areas of probability theory and mathematical statistics to illustrate the usefulness of this concept. Stable convergence holds in many limit theorems of probability theory and statistics – such as the classical central limit theorem – which are usually formulated in terms of convergence in distribution. Originated by Alfred Rényi, the notion of stable convergence is stronger than the classical weak convergence of probability measures. A variety of methods is described which can be used to establish this stronger stable convergence in many limit theorems which were originally formulated only in terms of weak convergence. Naturally, these stronger limit theorems have new and stronger consequences which should not be missed by neglecting the notion of stable convergence. The presentation will be accessible to researchers and advanced students at the master's level...

  11. Mixing process in the preparation of feed pellets at technological conditions rational parametres choice

    Directory of Open Access Journals (Sweden)

    E. S. Shentsova

    2016-01-01

    Full Text Available The mixing of ingredients – the most important process step in the manufacture of fodder pellets. The technology involves using molasses (warmed to 30–40 °C as a binder. In its composition is administered a mixture of salts of trace elements (copper sulfate, zinc sulfate, cobalt carbonate, potassium iodide, ferrous sulfate, manganese sulfate, sodium selenite, vitamins, salt, magnesium oxide, feed limestone, mono calcium phosphate and lime. Research on the development of feed pellets were carried out in laboratory conditions using experimental equipment. Mixer-reactor created the conditions for heating and temperature control of mass be mixed due to the occurring chemical reaction between water contained in the molasses, and the presence of oxides of calcium and magnesium. The choice of rational parameters of the mixing process upon receipt of fodder pellets allows to provide the high quality product with minimal energy costs. The ranges of the input information factors selected with the aid of a central rotatable uniforms-planning allowed with 56 experiments in a third-multiple replication to obtain the regression equation adequately describing the mixing process. The main factors were: the content of molasses, %; the content of calcium oxide, %; frequency of rotation of the stirrer, rpm; the content of salt in the recipe, %; the temperature of blending, °C. Output factors – productivity, kg/h; energy consumption, kWh; homogeneity of mixing, %. In the result of experiments impact factors and mathematical model of the process that allows to define output parameters within chosen ranges of variation of input factors are obtained. Greatest influence – the content of molasses in the product, the lowest – content of salt in the recipe. Efficiency of mixing hard distributed components pertaining to the most important biologically active substances was evaluated. Content (% of entered of vitamins and minerals in the pellets did not differ

  12. Stable isotope labeling strategy based on coding theory

    Energy Technology Data Exchange (ETDEWEB)

    Kasai, Takuma; Koshiba, Seizo; Yokoyama, Jun; Kigawa, Takanori, E-mail: kigawa@riken.jp [RIKEN Quantitative Biology Center (QBiC), Laboratory for Biomolecular Structure and Dynamics (Japan)

    2015-10-15

    We describe a strategy for stable isotope-aided protein nuclear magnetic resonance (NMR) analysis, called stable isotope encoding. The basic idea of this strategy is that amino-acid selective labeling can be considered as “encoding and decoding” processes, in which the information of amino acid type is encoded by the stable isotope labeling ratio of the corresponding residue and it is decoded by analyzing NMR spectra. According to the idea, the strategy can diminish the required number of labelled samples by increasing information content per sample, enabling discrimination of 19 kinds of non-proline amino acids with only three labeled samples. The idea also enables this strategy to combine with information technologies, such as error detection by check digit, to improve the robustness of analyses with low quality data. Stable isotope encoding will facilitate NMR analyses of proteins under non-ideal conditions, such as those in large complex systems, with low-solubility, and in living cells.

  13. Stable isotope labeling strategy based on coding theory

    International Nuclear Information System (INIS)

    Kasai, Takuma; Koshiba, Seizo; Yokoyama, Jun; Kigawa, Takanori

    2015-01-01

    We describe a strategy for stable isotope-aided protein nuclear magnetic resonance (NMR) analysis, called stable isotope encoding. The basic idea of this strategy is that amino-acid selective labeling can be considered as “encoding and decoding” processes, in which the information of amino acid type is encoded by the stable isotope labeling ratio of the corresponding residue and it is decoded by analyzing NMR spectra. According to the idea, the strategy can diminish the required number of labelled samples by increasing information content per sample, enabling discrimination of 19 kinds of non-proline amino acids with only three labeled samples. The idea also enables this strategy to combine with information technologies, such as error detection by check digit, to improve the robustness of analyses with low quality data. Stable isotope encoding will facilitate NMR analyses of proteins under non-ideal conditions, such as those in large complex systems, with low-solubility, and in living cells

  14. Thermalydraulic processes in the reactor coolant system of a BWR under severe accident conditions

    International Nuclear Information System (INIS)

    Hodge, S.A.

    1990-01-01

    Boiling water reactors (BWRs) incorporate many unique structural features that make their expected response under severe accident conditions very different from that predicted in the case of pressurized water reactor accident sequences. Automatic main steam isolation valve (MIV) closure as the vessel water level approaches the top of the core would cause reactor vessel isolation while automatic recirculation pump trip would limit the in-vessel flows to those characteristic of natural circulation (as disturbed by vessel relief valve actuation). This paper provides a discussion of the BWR control blade, channel box, core plate, control rod guide tube, and reactor vessel safety relief valve (SRV) configuration and the effects of these structural components upon thermal hydraulic processes within the reactor vessel under severe accident conditions. The dominant BWR severe accident sequences as determined by probabilistic risk assessment are described and the expected timing of events for the unmitigated short-term station blackout severe accident sequence at the Peach Bottom atomic power station is presented

  15. Optimization of Processing Conditions of Traditional Cured Tuna Loins–Muxama

    Directory of Open Access Journals (Sweden)

    Eduardo Esteves

    2018-01-01

    Full Text Available Muxama is a traditional highly-valued food product prepared from dry-cured tuna loins in southern Portugal and Spain. The production procedure has seen little change over the last centuries. The muxama’s stability is due to reduced water activity. In addition, the drying method has secondary effects on characteristics of flavor, color, and the nutritional value of the product. Our objectives were to describe the dynamics of important physicochemical parameters such as moisture content, water activity (aW, NaCl concentration (as water–phase salt, ZNaCl, pH and color, during the salting and drying stages of muxama production, and to test the effect(s of changes in the traditional processing conditions followed in southern Portugal, aiming at optimizing the production procedure. The lowest values of moisture and aW and highest ZNaCl obtained after drying tuna loins for seven days at 20 °C exceeded the values reported for commercial products and have impact on the appearance (color of the product. Therefore, drying tuna loins at lower temperatures (ca. 14 °C is probably more appropriate. The results obtained in this study could be used in the design of future experiments at other conditions and to assess other quality parameters, e.g., total volatile base nitrogen (TVB-N, thiobarbituric acid reactive substances (TBA-RS, microorganism abundance and sensory attributes, and subsequent validation trials.

  16. Both the "What" and "Why" of Youth Sports Participation Matter; a Conditional Process Analysis.

    Science.gov (United States)

    Gjesdal, Siv; Appleton, Paul R; Ommundsen, Yngvar

    2017-01-01

    This study builds on previous research combining achievement goal orientation from Achievement Goal Theory and motivational regulation from Self-Determination Theory. The aim was to assess the combination of the "what" and "why" of youth sport activity, and how it relates to the need for competence and self-esteem. Achievement goal orientation, specifically task and ego, was employed to represent the "what", whilst intrinsic and external regulation reflected the "why". Based on a sample of 496 youth sports participants, structural equation modeling with a bootstrapping procedure was used to examine whether the indirect relationship between achievement goal orientation and self-esteem was conditional to motivational regulation. The results show partial support for the conditional process models. Specifically, task orientation was indirectly linked with self-esteem through competence need, and the relationship was stronger with higher levels of intrinsic regulation for sport. Furthermore, ego orientation was negatively associated with self-esteem through a positive relationship with competence frustration. However, this relationship emerged only for those higher in intrinsic regulation. External regulation did not emerge as a moderator, but presented a positive relationship with competence frustration. Findings are discussed in light of both Achievement Goal Theory and Self-Determination Theory, and underline the importance of considering both the "what" and "why" when attempting to understand motivation in youth sport.

  17. Super-emitters in natural gas infrastructure are caused by abnormal process conditions

    Science.gov (United States)

    Zavala-Araiza, Daniel; Alvarez, Ramón A.; Lyon, David R.; Allen, David T.; Marchese, Anthony J.; Zimmerle, Daniel J.; Hamburg, Steven P.

    2017-01-01

    Effectively mitigating methane emissions from the natural gas supply chain requires addressing the disproportionate influence of high-emitting sources. Here we use a Monte Carlo simulation to aggregate methane emissions from all components on natural gas production sites in the Barnett Shale production region (Texas). Our total emission estimates are two-thirds of those derived from independent site-based measurements. Although some high-emitting operations occur by design (condensate flashing and liquid unloadings), they occur more than an order of magnitude less frequently than required to explain the reported frequency at which high site-based emissions are observed. We conclude that the occurrence of abnormal process conditions (for example, malfunctions upstream of the point of emissions; equipment issues) cause additional emissions that explain the gap between component-based and site-based emissions. Such abnormal conditions can cause a substantial proportion of a site's gas production to be emitted to the atmosphere and are the defining attribute of super-emitting sites.

  18. When congruence breeds preference: the influence of selective attention processes on evaluative conditioning.

    Science.gov (United States)

    Blask, Katarina; Walther, Eva; Frings, Christian

    2017-09-01

    We investigated in two experiments whether selective attention processes modulate evaluative conditioning (EC). Based on the fact that the typical stimuli in an EC paradigm involve an affect-laden unconditioned stimulus (US) and a neutral conditioned stimulus (CS), we started from the assumption that learning might depend in part upon selective attention to the US. Attention to the US was manipulated by including a variant of the Eriksen flanker task in the EC paradigm. Similarly to the original Flanker paradigm, we implemented a target-distracter logic by introducing the CS as the task-relevant stimulus (i.e. the target) to which the participants had to respond and the US as a task-irrelevant distracter. Experiment 1 showed that CS-US congruence modulated EC if the CS had to be selected against the US. Specifically, EC was more pronounced for congruent CS-US pairs as compared to incongruent CS-US pairs. Experiment 2 disentangled CS-US congruence and CS-US compatibility and suggested that it is indeed CS-US stimulus congruence rather than CS-US response compatibility that modulates EC.

  19. Effect of ohmic heating processing conditions on color stability of fungal pigments.

    Science.gov (United States)

    Aguilar-Machado, Diederich; Morales-Oyervides, Lourdes; Contreras-Esquivel, Juan C; Aguilar, Cristóbal; Méndez-Zavala, Alejandro; Raso, Javier; Montañez, Julio

    2017-06-01

    The aim of this work was to analyze the effect of ohmic heating processing conditions on the color stability of a red pigment extract produced by Penicillium purpurogenum GH2 suspended in a buffer solution (pH 6) and in a beverage model system (pH 4). Color stability of pigmented extract was evaluated in the range of 60-90 ℃. The degradation pattern of pigments was well described by the first-order (fractional conversion) and Bigelow model. Degradation rate constants ranged between 0.009 and 0.088 min -1 in systems evaluated. Significant differences in the rate constant values of the ohmic heating-treated samples in comparison with conventional thermal treatment suggested a possible effect of the oscillating electric field generated during ohmic heating. The thermodynamic analysis also indicated differences in the color degradation mechanism during ohmic heating specifically when the pigment was suspended in the beverage model system. In general, red pigments produced by P. purpurogenum GH2 presented good thermal stability under the range of the evaluated experimental conditions, showing potential future applications in pasteurized food matrices using ohmic heating treatment.

  20. Effect of cooking or handling conditions on the furan levels of processed foods.

    Science.gov (United States)

    Kim, T-K; Lee, Y-K; Park, Y S; Lee, K-G

    2009-06-01

    The aim of this study was to investigate the possible effects of cooking or handling conditions on the concentration of furan in processed foods. The analytical method used to analyse furan levels in foods was optimized based on solid-phase microextraction-gas chromatography-mass spectrometry (SPME-GC-MS). In baby soups, the concentration of furan decreased by up to 22% after opening a lid for 10 min. In the baby food in retort packaging, the level of furan was reduced by 15-33% after heating the foods at 50 degrees C without a lid. Furan in rice seasonings was evaporated completely after heating the foods at 60 degrees C. Regarding powered milk, the levels of furan were too low to be compared under various conditions. The levels of furan decreased to 58% in beverage products for babies, after storing them at 4 degrees C for 1 day without a lid. The levels of furan in canned foods such as cereal and vegetable were reduced by zero to 52% when they were stored without stirring in a refrigerator at 4 degrees C for 1 day. When we boiled canned fish, the furan present was almost completely evaporated. It is recommended that canned meats be heated up to 50-70 degrees C for the reduction (26-46%) of furan levels. The levels of furan in instant and brewed coffee samples were significantly reduced after storing for 11 to 20 min at room temperature without a lid (p < 0.05).

  1. Fermentation Process of Cocoa Based on Optimum Condition of Pulp PectinDepolymerization by Endogenous Pectolityc Enzymes

    OpenAIRE

    Ganda-Putra, G.P; Wrasiati, L.P; Wartini, N.M

    2010-01-01

    Pulp degradation during cocoa fermentation can be carried out by depolymerization process of pulp pectin using endogenous pectolytic enzymes at optimum condition. The objectives of this research were to study the effect of fermentation process based on optimum condition in terms of temperature and pH of pulp pectin depolymerization using endogenous pectolytic enzymes polygalakturonase (PG) and pectin metyl esterase (PME) and fermentation period in cocoa processing on quality characteristics o...

  2. Tempered stable laws as random walk limits

    OpenAIRE

    Chakrabarty, Arijit; Meerschaert, Mark M.

    2010-01-01

    Stable laws can be tempered by modifying the L\\'evy measure to cool the probability of large jumps. Tempered stable laws retain their signature power law behavior at infinity, and infinite divisibility. This paper develops random walk models that converge to a tempered stable law under a triangular array scheme. Since tempered stable laws and processes are useful in statistical physics, these random walk models can provide a basic physical model for the underlying physical phenomena.

  3. Oxidation of adsorbed ferrous iron: kinetics and influence of process conditions.

    Science.gov (United States)

    Buamah, R; Petrusevski, B; Schippers, J C

    2009-01-01

    For the removal of iron from groundwater, aeration followed with rapid (sand) filtration is frequently applied. Iron removal in this process is achieved through oxidation of Fe(2 + ) in aqueous solution followed by floc formation as well as adsorption of Fe(2 + ) onto the filter media. The rate of oxidation of the adsorbed Fe(2 + ) on the filter media plays an important role in this removal process. This study focuses on investigating the effect of pH on the rate of oxidation of adsorbed Fe(2 + ). Fe(2 + ) has been adsorbed, under anoxic conditions, on iron oxide coated sand (IOCS) in a short filter column and subsequently oxidized by feeding the column with aerated water. Ferrous ions adsorbed at pH 5, 6, 7 and 8 demonstrated consumption of oxygen, when aerated water was fed into the column. The oxygen uptake at pH 7 and 8 was faster than at pH 5 and 6. However the difference was less pronounced than expected. The difference is attributed to the pH buffering effect of the IOCS. At feedwater pH 5, 6 and 7 the pH in the effluent was higher than in the influent, while a pH drop should occur because of oxidation of adsorbed Fe(2 + ). At pH 8, the pH dropped. These phenomena are attributed to the presence of calcium and /or ferrous carbonate in IOCS.

  4. Preliminary assessment of safeguardability on the concepture design of advanced spent fuel conditioning process

    International Nuclear Information System (INIS)

    Lee, Sang Yoon; Ha, Jang Ho; Ko, Won Il; Song, Dae Yong; Kim, Ho Dong

    2003-04-01

    In this report, a preliminary study on the safeguardability of ACP (Advanced spent fuel Conditioning Process) was conducted with Los Alamos National Laboratory. The proposed ACP concept is an electrometallurgical treatment technique to convert oxide-type spent nuclear fuels into metal forms, which can achieve significant reduction of the volume and heat load of spent fuel to be stored and disposed of. For the safeguardability analysis of the ACP facility, sub-processes and their KMPs (Key Measurement Points) were defined first, and then their material flows were analyzed. Finally, the standard deviation of the Inventory Difference (ID) value of the facility was estimated with assumption by assuming international target values for the uncertainty of measurement methods and their uncertainty. From the preliminary calculation, we concluded that if the assumptions regarding measurement instruments can be achieved in a safeguards system for the ACP facility, the safeguards goals of International Atomic Energy Agency (IAEA) could be met. In the second phase of this study, further study on sensitivity analyses considering various factors such as measurement errors, facility capacities, MBA periods etc. may be needed

  5. Influence of thermal processing conditions on flavor stability in fluid milk: benzaldehyde.

    Science.gov (United States)

    Potineni, R V; Peterson, D G

    2005-01-01

    Flavor loss in dairy products has been associated with enzymatic degradation by xanthine oxidase. This study was conducted to investigate the influence of milk thermal processing conditions (or xanthine oxidase inactivation) on benzaldehyde stability. Benzaldehyde was added to whole milk which had been thermally processed at 4 levels: (1) none or raw, (2) high temperature, short time (HTST) pasteurization, (3) HTST pasteurization, additionally heated to 100 degrees C (PAH), and (4) UHT sterilized. Additionally, PAH and UHT milk samples containing benzaldehyde (with and without ferrous sulfate) were spiked with xanthine oxidase. Azide was added as an antimicrobial agent (one additional pasteurized sample without) and the microbial load (total plate count) was determined on d 0, 2, and 6. The concentration of benzaldehyde and benzoic acid in all milk samples were determined at d 0, 1, 2, 4, and 6 (stored at 5 degrees C) by gas chromatography/mass spectrometry in selective ion monitory mode. Over the 6-d storage period, more than 80% of the benzaldehyde content was converted (oxidized) to benzoic acid in raw and pasteurized milk, whereas no change in the benzaldehyde concentration was found in PAH or UHT milk samples. Furthermore, the addition of xanthine oxidase or xanthine oxidase plus ferrous sulfate to PAH or UHT milk samples did not result in benzaldehyde degradation over the storage period.

  6. Preliminary assessment of safeguardability on the concepture design of advanced spent fuel conditioning process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Sang Yoon; Ha, Jang Ho; Ko, Won Il; Song, Dae Yong; Kim, Ho Dong

    2003-04-01

    In this report, a preliminary study on the safeguardability of ACP (Advanced spent fuel Conditioning Process) was conducted with Los Alamos National Laboratory. The proposed ACP concept is an electrometallurgical treatment technique to convert oxide-type spent nuclear fuels into metal forms, which can achieve significant reduction of the volume and heat load of spent fuel to be stored and disposed of. For the safeguardability analysis of the ACP facility, sub-processes and their KMPs (Key Measurement Points) were defined first, and then their material flows were analyzed. Finally, the standard deviation of the Inventory Difference (ID) value of the facility was estimated with assumption by assuming international target values for the uncertainty of measurement methods and their uncertainty. From the preliminary calculation, we concluded that if the assumptions regarding measurement instruments can be achieved in a safeguards system for the ACP facility, the safeguards goals of International Atomic Energy Agency (IAEA) could be met. In the second phase of this study, further study on sensitivity analyses considering various factors such as measurement errors, facility capacities, MBA periods etc. may be needed.

  7. Placement of the radiochemical processing plant at Oak Ridge National Laboratory into a safe standby condition

    International Nuclear Information System (INIS)

    Holladay, D.W.; Bopp, C.D.; Farmer, A.J.; Johnson, J.K.; Miller, C.H.; Powers, B.A.; Collins, E.D.

    1986-01-01

    Extensive upgrade, cleanup, and decontamination efforts are being conducted for appropriate areas in the Radiochemical Processing Plant (RPP) with the goal of achieving safe standby condition by the end of FY 1989. The ventilation system must maintain containment thus, it is being upgraded via demolition and replacement of marginally adequate ductwork, fans, and control systems. Areas that are being decontaminated and stripped of various services (e.g., piping, ductwork, and process tanks) include hot cells, makeup rooms, and pipe tunnels. Operating equipment that is being decontaminated includes glove boxes and hoods. Replacement of the ventilation system and removal of equipment from pipe tunnels, cells, and makeup rooms are accomplished by contact labor by workers using proper attire, safety rules, and shielding, Removal of contaminated ductwork and piping is conducted with containment enclosures that are strategically located at breakpoints, and methods of separation are chosen to conform with health physics requirements. The methods of cutting contaminated piping and ductwork include portable reciprocating saws, pipe cutters, burning, and plasma torch. Specially designed containment enclosures will be used to prevent the spread of radioactive contamination while maintaining adequate ventilation

  8. Numerical simulation of the shot peening process under previous loading conditions

    International Nuclear Information System (INIS)

    Romero-Ángeles, B; Urriolagoitia-Sosa, G; Torres-San Miguel, C R; Molina-Ballinas, A; Benítez-García, H A; Vargas-Bustos, J A; Urriolagoitia-Calderón, G

    2015-01-01

    This research presents a numerical simulation of the shot peening process and determines the residual stress field induced into a component with a previous loading history. The importance of this analysis is based on the fact that mechanical elements under shot peening are also subjected to manufacturing processes, which convert raw material into finished product. However, material is not provided in a virgin state, it has a previous loading history caused by the manner it is fabricated. This condition could alter some beneficial aspects of the residual stress induced by shot peening and could accelerate the crack nucleation and propagation progression. Studies were performed in beams subjected to strain hardening in tension (5ε y ) before shot peening was applied. Latter results were then compared in a numerical assessment of an induced residual stress field by shot peening carried out in a component (beam) without any previous loading history. In this paper, it is clearly shown the detrimental or beneficial effect that previous loading history can bring to the mechanical component and how it can be controlled to improve the mechanical behavior of the material

  9. Influence of processing conditions on the glass-crystal transition into borosilicate glasses

    Energy Technology Data Exchange (ETDEWEB)

    Deschanels, X.; Cachia, J.N.; Lopez, C.; Peuget, S. [CEA Marcoule, BP 17171, 30207 Bagnols sur Ceze (France)

    2008-07-01

    The precipitation of a crystalline phase in glass is observed when one element exceeds its loading limit (i.e.: solubility limit). In this work we have studied the solubility of different actinides and surrogates (lanthanides and hafnium) in borosilicate glass used for the immobilization of the high-level nuclear waste (HLW glasses). The results obtained show an increase of the solubility limits of these elements with the processing temperature and the redox potential of the melt. The elements at the oxidation state (III) exhibit a higher solubility than the element at oxidation state (IV). In this framework, cerium is an interesting element because its oxidation state tunes from (IV) to (III) as a function of the processing conditions. It is shown that the solubility of cerium can be multiplied by a factor of 20 at 1100 C. degrees. In order to have a better understanding of the mechanisms that underline the evolution of the solubility, XAFS and NMR investigation has been undertaken. Trivalent elements present the characteristics of network-modified cations while tetravalent elements look like network-former cations.

  10. Placement of the radiochemical processing plant at Oak Ridge National Laboratory into a safe standby condition

    International Nuclear Information System (INIS)

    Holladay, D.W.; Bopp, C.D.; Farmer, A.J.; Johnson, J.K.; Miller, C.H.; Powers, B.A.; Collins, E.D.

    1986-01-01

    Extensive upgrade, cleanup, and decontamination efforts are being conducted for appropriate areas in the Radiochemical Processing Plant (RPP) with the goal of achieving ''safe standby'' condition by the end of FY 1989. The ventilation system must maintain containment; thus, it is being upgraded via demolition and replacement of marginally adequate ductwork, fans, and control systems. Areas that are being decontaminated and stripped of various services (e.g., piping, ductwork, and process tanks) include hot cells, makeup rooms, and pipe tunnels. Operating equipment that is being decontaminated includes glove boxes and hoods. Replacement of the ventilation system and removal of equipment from pipe tunnels, cells, and makeup rooms are accomplished by contact labor by workers using proper attire, safety rules, and shielding. Removal of contaminated ductwork and piping is conducted with containment enclosures that are strategically located at breakpoints, and methods of separation are chosen to conform with health physics requirements. The methods of cutting contaminated piping and ductwork include portable reciprocating saws, pipe cutters, burning, and plasma torch. Specially designed containment enclosures will be used to prevent the spread of radioactive contamination while maintaining adequate ventilation. 6 figs

  11. Cosmic ray processing of N2-containing interstellar ice analogues at dark cloud conditions

    Science.gov (United States)

    Fedoseev, G.; Scirè, C.; Baratta, G. A.; Palumbo, M. E.

    2018-04-01

    N2 is believed to lock considerable part of nitrogen elemental budget and, therefore, to be one of the most abundant ice constituent in cold dark clouds. This laboratory-based research utilizes high energetic processing of N2 containing interstellar ice analogues using 200 keV H+ and He+ ions that mimics cosmic ray processing of the interstellar icy grains. It aims to investigate the formation of (iso)cyanates and cyanides in the ice mantles at the conditions typical for cold dark clouds and prestellar cores. Investigation of cosmic ray processing as a chemical trigger mechanism is explained by the high stability of N2 molecules that are chemically inert in most of the atom- and radical-addition reactions and cannot be efficiently dissociated by cosmic ray induced UV-field. Two sets of experiments are performed to closer address solid-state chemistry occurring in two distinct layers of the ice formed at different stages of dark cloud evolution, i.e. `H2O-rich' and `CO-rich' ice layers. Formation of HNCO and OCN- is discussed in all of the performed experiments. Corresponding kinetic curves for HNCO and OCN- are obtained. Furthermore, a feature around 2092 cm-1 assigned to the contributions of 13CO, CN-, and HCN is analysed. The kinetic curves for the combined HCN/CN- abundance are derived. In turn, normalized formation yields are evaluated by interpolation of the obtained results to the low irradiation doses relevant to dark cloud stage. The obtained values can be used to interpret future observations towards cold dark clouds using James Webb Space Telescope.

  12. Extraversion, Neuroticism, and Verbal Conditioning of Affective Self-Disclosures

    Science.gov (United States)

    Hekmat, Hamid

    1971-01-01

    Subjects were assigned to four experimental groups: neurotic extraverts, stable extraverts, neurotic introverts, stable introverts, and a control group. Results indicated that introversion, and not neuroticism, facilitated conditioning processes. Neuroticism, however, did not interact on the conditioning of affective self disclosures. Introverted…

  13. Insights from stable S and O isotopes into biogeochemical processes and genesis of Lower Cambrian barite–pyrite concretions of South China

    Digital Repository Service at National Institute of Oceanography (India)

    Goldberg, T.; Mazumdar, A.; Strauss, H.; Shields, G.

    water trace metal chemistry of laminated sediments from the Gulf of California, Mexico. Marine Chemistry 14, 89-106. Canfield, D.E., 2001. Biogeochemistry of sulphur isotopes. In: Valley, J.W. & Cole, D.R. (Eds.), Stable Isotope Geochemistry. Reviews.... Age curves of sulphur and oxygen isotopes in marine sulphate and their mutual interpretation. Chemical Geology 28, 199-206. Coleman, M.L. & Raiswell, R., 1981. Carbon, oxygen and sulphur isotope variations in concretions from the Upper Lias of N...

  14. Transportability Class of Americium in K Basin Sludge under Ambient and Hydrothermal Processing Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Delegard, Calvin H.; Schmitt, Bruce E.; Schmidt, Andrew J.

    2006-08-01

    of the K Basin sludge characterization data is derived spent nuclear fuel corroded within the K Basins at 10-15?C. The STP process will place water-laden sludges from the K Basin in process vessels at {approx}150-180 C. Therefore, published studies with other irradiated (uranium oxide) fuel were examined. From these studies, the affinity of plutonium and americium for uranium in irradiated UO2 also was demonstrated at hydrothermal conditions (150 C anoxic liquid water) approaching those proposed for the STP process and even for hydrothermal conditions outside of the STP operating envelope (e.g., 150 C oxic and 100 C oxic and anoxic liquid water). In summary, by demonstrating that the chemical and physical behavior of 241Am in the sludge matrix is similar to that of the predominant species (uranium and for the plutonium from which it originates), a technical basis is provided for using the slow uptake transportability factor for 241Am that is currently used for plutonium and uranium oxides. The change from moderate to slow uptake for 241Am could reduce the overall analyzed dose consequences for the STP by more than 30%.

  15. Polyhydroxyalkanoate Production on Waste Water Treatment Plants: Process Scheme, Operating Conditions and Potential Analysis for German and European Municipal Waste Water Treatment Plants

    Directory of Open Access Journals (Sweden)

    Timo Pittmann

    2017-06-01

    Full Text Available This work describes the production of polyhydroxyalkanoates (PHA as a side stream process on a municipal waste water treatment plant (WWTP and a subsequent analysis of the production potential in Germany and the European Union (EU. Therefore, tests with different types of sludge from a WWTP were investigated regarding their volatile fatty acids (VFA production-potential. Afterwards, primary sludge was used as substrate to test a series of operating conditions (temperature, pH, retention time (RT and withdrawal (WD in order to find suitable settings for a high and stable VFA production. In a second step, various tests regarding a high PHA production and stable PHA composition to determine the influence of substrate concentration, temperature, pH and cycle time of an installed feast/famine-regime were conducted. Experiments with a semi-continuous reactor operation showed that a short RT of 4 days and a small WD of 25% at pH = 6 and around 30 °C is preferable for a high VFA production rate (PR of 1913 mgVFA/(L×d and a stable VFA composition. A high PHA production up to 28.4% of cell dry weight (CDW was reached at lower substrate concentration, 20 °C, neutral pH-value and a 24 h cycle time. A final step a potential analysis, based on the results and detailed data from German waste water treatment plants, showed that the theoretically possible production of biopolymers in Germany amounts to more than 19% of the 2016 worldwide biopolymer production. In addition, a profound estimation regarding the EU showed that in theory about 120% of the worldwide biopolymer production (in 2016 could be produced on European waste water treatment plants.

  16. Evaluative Processing of Food Images: A Conditional Role for Viewing in Preference Formation

    Directory of Open Access Journals (Sweden)

    Alexandra Wolf

    2018-06-01

    Full Text Available Previous research suggested a role of gaze in preference formation, not merely as an expression of preference, but also as a causal influence. According to the gaze cascade hypothesis, the longer subjects look at an item, the more likely they are to develop a preference for it. However, to date the connection between viewing and liking has been investigated predominately with self-paced viewing conditions in which the subjects were required to select certain items from simultaneously presented stimuli on the basis of perceived visual attractiveness. Such conditions might promote a default, but non-mandatory connection between viewing and liking. To explore whether the connection is separable, we examined the evaluative processing of single naturalistic food images in a 2 × 2 design, conducted completely within subjects, in which we varied both the type of exposure (self-paced versus time-controlled and the type of evaluation (non-exclusive versus exclusive. In the self-paced exclusive evaluation, longer viewing was associated with a higher likelihood of a positive evaluation. However, in the self-paced non-exclusive evaluation, the trend reversed such that longer viewing durations were associated with lesser ratings. Furthermore, in the time-controlled tasks, both with non-exclusive and exclusive evaluation, there was no significant relationship between the viewing duration and the evaluation. The overall pattern of results was consistent for viewing times measured in terms of exposure duration (i.e., the duration of stimulus presentation on the screen and in terms of actual gaze duration (i.e., the amount of time the subject effectively gazed at the stimulus on the screen. The data indicated that viewing does not intrinsically lead to a higher evaluation when evaluating single food images; instead, the relationship between viewing duration and evaluation depends on the type of task. We suggest that self-determination of exposure duration may

  17. Extraction of red cabbage anthocyanins: optimization of the operation conditions of the column process

    Directory of Open Access Journals (Sweden)

    Marcelo Fonseca Xavier

    2008-02-01

    Full Text Available The aim of this work was to extract anthocyanins from the red cabbage. Batch studies under several extraction conditions indicated that acetic acid in aqueous solution (10% V/V was the best solvent, used in the proportion of 0.25 g of red cabbage mL-1. At this condition, column assays were carried out to evaluate the influence of the ionic force, pH, solvent flow rate, recirculated volume of red cabbage juice and the mass of red cabbage. Results showed that the pH, recirculation and mass of red cabbage had statistically significant effects, where the optimum operation conditions found for the process were pH 2.3, recirculation volume of the solvent 0.83 L and mass of red cabbage 50 g.Desde os primórdios dos tempos as antocianinas são extraídas de vegetais, mas avanços que garantam um processo viável e rentável exigem conhecimento, quantificação e controle das condições de operação. Estudos em batelada sob várias condições de extração indicaram que ácido acético em solução aquosa (10% V/V foi o melhor solvente, quando usado na proporção de 0,25 g de repolho roxo mL-1. Nesta condição de operação foram feitos ensaios em coluna para avaliar a influência da força iônica, pH, taxa de escoamento do solvente, volume recirculado da solução de extração e massa de repolho roxo. Os resultados mostraram que o pH, recirculação e massa de repolho foram estatisticamente significativos, e as condições ótimas de operação encontradas para o processo foram pH 2,3, volume de solvente recirculado de 0,83 L e massa de repolho roxo igual a 50g.

  18. Angina Pectoris (Stable Angina)

    Science.gov (United States)

    ... Peripheral Artery Disease Venous Thromboembolism Aortic Aneurysm More Angina Pectoris (Stable Angina) Updated:Aug 21,2017 You may have heard the term “angina pectoris” or “stable angina” in your doctor’s office, ...

  19. Autolytic degradation of skipjack tuna during heating as affected by initial quality and processing conditions.

    Science.gov (United States)

    Stagg, Nicola J; Amato, Penny M; Giesbrecht, Francis; Lanier, Tyre C

    2012-02-01

    Several factors were studied as affecting protein degradation and texture of skipjack tuna muscle following ambient pressure thermal processing (precooking). These included degree of mushy tuna syndrome (MTS) evidenced in the raw meat, raw meat pH, abusive thawing/holding, and precooking temperature/time. Slurries and intact pieces from frozen skipjack tuna, either tempered for 2 h or thawed and held at 25 °C for 22 h (abusive treatment) were heated at temperatures ranging from 40 to 80 °C for up to 2 h, and also at 90 °C for 1 h, with or without prior adjustment of pH to 5 or 7 to favor cathepsin or calpain activity, respectively. Proteolysis of precooked samples was monitored by Lowry assay and SDS-PAGE; cooked texture of intact meat was measured using a Kramer shear press and by sensory profile analysis. Proteolysis maximally occurred in slurries of skipjack tuna muscle that had been abusively stored (22 h at 25 °C) and adjusted to pH 5 prior to heating at 55 °C. Intact pieces of tuna abusively thawed/held for 22 h with subsequent heating at 55 °C also evidenced the most proteolysis and were the least firm in texture. Raw fish that evidenced higher severity of MTS when raw displayed higher levels of proteolysis prior to cooking, which were further increased after cooking at 55 °C. The kinetic data presented here can be used to optimize processing conditions for skipjack tuna canning to minimize textural degradation and optimize quality. © 2012 Institute of Food Technologists®

  20. Operating Conditions of Coagulation-Flocculation Process for High Turbidity Ceramic Wastewater

    Directory of Open Access Journals (Sweden)

    Sameer Al-Asheh

    2017-04-01

    Full Text Available This work attempted to determine the optimum conditions required for the coagulation and flocculation process as an essential stage of the ceramic wastewater treatment. Coagulation and flocculation is a very necessary step in industries as it lessens turbidity, color, and odor of wastewater. The experimental work was performed in several runs. The volume of wastewater used in each run was 200 mL and was kept at this value throughout. In certain runs, the speed of the mixer was varied while keeping the quantity of coagulant and flocculant constant in order to determine the optimum speed that resulted in the least turbidity. A speed of 5% was chosen as the ideal process speed according to the results obtained. Next, experiments were operated at this optimum speed while changing the dosage of coagulant and flocculant in order to decide the optimum dosage. Coagulant and flocculent amounts of 0.4 g (without booster and 0.2 g (with booster selected after the readings were taken. For all the readings, a turbidity meter was used providing results in Nephelometric Turbidity Units (NTU. Lowest turbidity was achieved when using 5% speed with 0.4 grams of coagulant and 0.4 grams of flocculant, or 5% speed with 0.2 grams of coagulant, 0.2 grams of flocculant and 0.25 g/L of booster coagulant. According to factorial design analysis, such as parameters as impeller speed and dosage have an influential impact on the turbidity; while the booster has insignificant influence and other interactions between parameters are important.

  1. Know the risk, take the win: how executive functions and probability processing influence advantageous decision making under risk conditions.

    Science.gov (United States)

    Brand, Matthias; Schiebener, Johannes; Pertl, Marie-Theres; Delazer, Margarete

    2014-01-01

    Recent models on decision making under risk conditions have suggested that numerical abilities are important ingredients of advantageous decision-making performance, but empirical evidence is still limited. The results of our first study show that logical reasoning and basic mental calculation capacities predict ratio processing and that ratio processing predicts decision making under risk. In the second study, logical reasoning together with executive functions predicted probability processing (numeracy and probability knowledge), and probability processing predicted decision making under risk. These findings suggest that increasing an individual's understanding of ratios and probabilities should lead to more advantageous decisions under risk conditions.

  2. Processing conditions and microstructural features of porous 316L stainless steel components by DMLS

    Energy Technology Data Exchange (ETDEWEB)

    Gu Dongdong [College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, 29 Yudao Street, 210016 Nanjing (China)], E-mail: dongdonggu@nuaa.edu.cn; Shen Yifu [College of Materials Science and Technology, Nanjing University of Aeronautics and Astronautics, 29 Yudao Street, 210016 Nanjing (China)

    2008-12-30

    Direct metal laser sintering (DMLS), due to its flexibility in materials and shapes, would be especially interesting to produce complex shaped porous metallic components. In the present work, processing conditions and microstructural characteristics of direct laser sintered porous 316L stainless steel components were studied. It was found that a partial melting mechanism of powders gave a high feasibility in obtaining porous sintered structures possessing porosities of {approx}21-{approx}55%. Linear energy density (LED), which was defined by the ratio of laser power to scan speed, was used to tailor the laser sintering mechanism. A moderate LED of {approx}3400-{approx}6000 J/m and a lower scan speed less than 0.06 m/s proved to be feasible. With the favorable sintering mechanism prevailed, lowering laser power or increasing scan speed, scan line spacing, and powder layer thickness generally led to a higher porosity. Metallurgical mechanisms of pore formation during DMLS were addressed. It showed that the presence of pores was through: (i) the formation of liquid bridges between partially melted particles during laser irradiation; and (ii) the growth of sintering necks during solidification, leaving residual pores between solidified metallic agglomerates.

  3. Processing conditions and microstructural features of porous 316L stainless steel components by DMLS

    Science.gov (United States)

    Gu, Dongdong; Shen, Yifu

    2008-12-01

    Direct metal laser sintering (DMLS), due to its flexibility in materials and shapes, would be especially interesting to produce complex shaped porous metallic components. In the present work, processing conditions and microstructural characteristics of direct laser sintered porous 316L stainless steel components were studied. It was found that a partial melting mechanism of powders gave a high feasibility in obtaining porous sintered structures possessing porosities of ˜21-˜55%. Linear energy density (LED), which was defined by the ratio of laser power to scan speed, was used to tailor the laser sintering mechanism. A moderate LED of ˜3400-˜6000 J/m and a lower scan speed less than 0.06 m/s proved to be feasible. With the favorable sintering mechanism prevailed, lowering laser power or increasing scan speed, scan line spacing, and powder layer thickness generally led to a higher porosity. Metallurgical mechanisms of pore formation during DMLS were addressed. It showed that the presence of pores was through: (i) the formation of liquid bridges between partially melted particles during laser irradiation; and (ii) the growth of sintering necks during solidification, leaving residual pores between solidified metallic agglomerates.

  4. The Effect of Selected Conditions in a Thermoforming Process on Wall Thickness Variations

    Directory of Open Access Journals (Sweden)

    Emil Sasimowski

    2017-12-01

    Full Text Available The paper reports the results of a study on the effect of selected conditions in a thermoforming process for thin polystyrene sheet by vacuum assisted drape forming on the wall thickness non-uniformity of finished parts. The investigation was performed using Statistica’s DOE module for three variables: temperatures in the external and internal zones of the heater as well as heating time of the plastic sheet. The results demonstrate that the wall thickness in the finished parts at the measuring points is primarily affected by the heating time and the temperature in the internal zone of the heater, while the temperature in the external zone only affects some regions of the finished part. The results demonstrate that a short heating time and hence a lower temperature of the plastic sheet lead to a more uniform deformation of both the bottom and the side walls of the finished part, and as a consequence, to smaller variations in the wall thickness. The shortening of the heating time is however limited by the necessity of accurate reproduction of the shape of the finished part.

  5. Effect of process parameters on optimum welding condition of DP590 steel by friction stir welding

    International Nuclear Information System (INIS)

    Kim, Young Gon; Kim, Ji Sun; Kim, In Ju

    2014-01-01

    In the automotive industry, vehicle weight reduction techniques have been actively studied to improve the rate of fuel consumption and to cope with the regulation restricting exhaust gas. For this reason, advanced high-strength steel (AHSS) is preferred in the automobile industry as its tensile strength is 590 MPa and over. In this study, to obtain the optimum welding condition, the friction stir welding (FSW) process applied to AHSS was considered. The FSW experiment was performed on a stir plate using a Si 3 N 4 tool and a 1.4-mm thick DP590 steel sheet manufactured by cold rolling. In addition, to investigate the temperature distribution of the advancing and retreating sides in the welding state, the tool rotation speed of 800 rpm, and the welding speed of 180 mm/min, a K-type thermocouple was inserted in the backing plate, and the peak temperature was evaluated at each point. Especially, the correlation between the heat input per unit length and the formation of the FSW zone was minutely analyzed.

  6. Swarm motility inhibitory and antioxidant activities of pomegranate peel processed under three drying conditions.

    Science.gov (United States)

    John, K M Maria; Bhagwat, Arvind A; Luthria, Devanand L

    2017-11-15

    During processing of ready-to-eat fresh fruits, large amounts of peel and seeds are discarded as waste. Pomegranate (Punicagranatum) peels contain high amounts of bioactive compounds which inhibit migration of Salmonella on wet surfaces. The metabolic distribution of bioactives in pomegranate peel, inner membrane, and edible aril portion was investigated under three different drying conditions along with the anti-swarming activity against Citrobacter rodentium. Based on the multivariate analysis, 29 metabolites discriminated the pomegranate peel, inner membrane, and edible aril portion, as well as the three different drying methods. Punicalagins (∼38.6-50.3mg/g) were detected in higher quantities in all fractions as compared to ellagic acid (∼0.1-3.2mg/g) and punicalins (∼0-2.4mg/g). The bioactivity (antioxidant, anti-swarming) and phenolics content was significantly higher in peels than the edible aril portion. Natural anti-swarming agents from food waste may have promising potential for controlling food borne pathogens. Published by Elsevier Ltd.

  7. [Is it possible to "cancel" aging process of cell cultures under optimal conditions for cultivation?].

    Science.gov (United States)

    Bozhkov, A I; Kovaleva, M K; Menzianova, N G

    2011-01-01

    The characteristics of the cells epigenotypes Dunaliella viridis Teod. in the process of chronological and replicative aging were investigated. By 40th day of accumulative cultivation (which coincided with the stationary growth phase) DNA content in the cells of Dunaliella viridis increased 2 times, triacylglycerides 3 times, beta-carotene and carbonyl proteins 2 times, RNA content decreased in comparison with cells in exponential growth phase, i. e., the 40th day of growth of culture forms the age-related epigenotype. 4 received subcultures were being transplanted during 2 years in mid-logarithmic growth phase (subculture-10), early stationary phase of growth (subculture-20), in the mid-stationary growth phase (subculture-30), and late stationary growth phase (subculture-40). It is shown that epigenotype of subculture-10 remained unchanged over 2 years of cultivation, i. e., it does not manifest replicative aging. At the same time, the subculture-20, although long enough (at least 40 passages), maintained epigenotype characteristic of young cultures, and showed age-related changes. Pronounced age-dependent changes of epigenotype in the course of cultivation were identified for subculture-30, and subculture-40 was characterized by unstable epigenotype. Thus, cultivation conditions determine the intensity of replicative aging in Dunaliella viridis.

  8. Vaccinium meridionale Swartz Supercritical CO2 Extraction: Effect of Process Conditions and Scaling Up

    Directory of Open Access Journals (Sweden)

    Alexis López-Padilla

    2016-06-01

    Full Text Available Vaccinium meridionale Swartz (Mortiño or Colombian blueberry is one of the Vaccinium species abundantly found across the Colombian mountains, which are characterized by high contents of polyphenolic compounds (anthocyanins and flavonoids. The supercritical fluid extraction (SFE of Vaccinium species has mainly focused on the study of V. myrtillus L. (blueberry. In this work, the SFE of Mortiño fruit from Colombia was studied in a small-scale extraction cell (273 cm3 and different extraction pressures (20 and 30 MPa and temperatures (313 and 343 K were investigated. Then, process scaling-up to a larger extraction cell (1350 cm3 was analyzed using well-known semi-empirical engineering approaches. The Broken and Intact Cell (BIC model was adjusted to represent the kinetic behavior of the low-scale extraction and to simulate the large-scale conditions. Extraction yields obtained were in the range 0.1%–3.2%. Most of the Mortiño solutes are readily accessible and, thus, 92% of the extractable material was recovered in around 30 min. The constant CO2 residence time criterion produced excellent results regarding the small-scale kinetic curve according to the BIC model, and this conclusion was experimentally validated in large-scale kinetic experiments.

  9. Effect of process parameters on optimum welding condition of DP590 steel by friction stir welding

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Young Gon; Kim, Ji Sun; Kim, In Ju [Korea Institute of Industrial Technology, Gwangju (Korea, Republic of)

    2014-12-15

    In the automotive industry, vehicle weight reduction techniques have been actively studied to improve the rate of fuel consumption and to cope with the regulation restricting exhaust gas. For this reason, advanced high-strength steel (AHSS) is preferred in the automobile industry as its tensile strength is 590 MPa and over. In this study, to obtain the optimum welding condition, the friction stir welding (FSW) process applied to AHSS was considered. The FSW experiment was performed on a stir plate using a Si{sub 3}N{sub 4} tool and a 1.4-mm thick DP590 steel sheet manufactured by cold rolling. In addition, to investigate the temperature distribution of the advancing and retreating sides in the welding state, the tool rotation speed of 800 rpm, and the welding speed of 180 mm/min, a K-type thermocouple was inserted in the backing plate, and the peak temperature was evaluated at each point. Especially, the correlation between the heat input per unit length and the formation of the FSW zone was minutely analyzed.

  10. Optimizing fermentation process miscanthus-to-ethanol biorefinery scale under uncertain conditions

    International Nuclear Information System (INIS)

    Bomberg, Matthew; Sanchez, Daniel L; Lipman, Timothy E

    2014-01-01

    Ethanol produced from cellulosic feedstocks has garnered significant interest for greenhouse gas abatement and energy security promotion. One outstanding question in the development of a mature cellulosic ethanol industry is the optimal scale of biorefining activities. This question is important for companies and entrepreneurs seeking to construct and operate cellulosic ethanol biorefineries as it determines the size of investment needed and the amount of feedstock for which they must contract. The question also has important implications for the nature and location of lifecycle environmental impacts from cellulosic ethanol. We use an optimization framework similar to previous studies, but add richer details by treating many of these critical parameters as random variables and incorporating a stochastic sub-model for land conversion. We then use Monte Carlo simulation to obtain a probability distribution for the optimal scale of a biorefinery using a fermentation process and miscanthus feedstock. We find a bimodal distribution with a high peak at around 10–30 MMgal yr −1 (representing circumstances where a relatively low percentage of farmers elect to participate in miscanthus cultivation) and a lower and flatter peak between 150 and 250 MMgal yr −1 (representing more typically assumed land-conversion conditions). This distribution leads to useful insights; in particular, the asymmetry of the distribution—with significantly more mass on the low side—indicates that developers of cellulosic ethanol biorefineries may wish to exercise caution in scale-up. (letters)

  11. Optimizing fermentation process miscanthus-to-ethanol biorefinery scale under uncertain conditions

    Science.gov (United States)

    Bomberg, Matthew; Sanchez, Daniel L.; Lipman, Timothy E.

    2014-05-01

    Ethanol produced from cellulosic feedstocks has garnered significant interest for greenhouse gas abatement and energy security promotion. One outstanding question in the development of a mature cellulosic ethanol industry is the optimal scale of biorefining activities. This question is important for companies and entrepreneurs seeking to construct and operate cellulosic ethanol biorefineries as it determines the size of investment needed and the amount of feedstock for which they must contract. The question also has important implications for the nature and location of lifecycle environmental impacts from cellulosic ethanol. We use an optimization framework similar to previous studies, but add richer details by treating many of these critical parameters as random variables and incorporating a stochastic sub-model for land conversion. We then use Monte Carlo simulation to obtain a probability distribution for the optimal scale of a biorefinery using a fermentation process and miscanthus feedstock. We find a bimodal distribution with a high peak at around 10-30 MMgal yr-1 (representing circumstances where a relatively low percentage of farmers elect to participate in miscanthus cultivation) and a lower and flatter peak between 150 and 250 MMgal yr-1 (representing more typically assumed land-conversion conditions). This distribution leads to useful insights; in particular, the asymmetry of the distribution—with significantly more mass on the low side—indicates that developers of cellulosic ethanol biorefineries may wish to exercise caution in scale-up.

  12. The interactive biotic and abiotic processes of DDT transformation under dissimilatory iron-reducing conditions.

    Science.gov (United States)

    Jin, Xin; Wang, Fang; Gu, Chenggang; Yang, Xinglun; Kengara, Fredrick O; Bian, Yongrong; Song, Yang; Jiang, Xin

    2015-11-01

    The objective of the study was to elucidate the biotic and abiotic processes under dissimilatory iron reducing conditions involved in reductive dechlorination and iron reduction. DDT transformation was investigated in cultures of Shewanella putrefaciens 200 with/without α-FeOOH. A modified first-order kinetics model was developed and described DDT transformation well. Both the α-FeOOH reduction rate and the dechlorination rate of DDT were positively correlated to the biomass. Addition of α-FeOOH enhanced reductive dechlorination of DDT by favoring the cell survival and generating Fe(II) which was absorbed on the surface of bacteria and iron oxide. 92% of the absorbed Fe(II) was Na-acetate (1M) extractable. However, α-FeOOH also played a negative role of competing for electrons as reflected by the dechlorination rate of DDT was inhibited when increasing the α-FeOOH from 1 g L(-1) to 5 g L(-1). DDT was measured to be toxic to S. putrefaciens 200. The metabolites DDD, DDE and DDMU were recalcitrant to S. putrefaciens 200. The results suggested that iron oxide was not the key factor to promote the dissipation of DDX (DDT and the metabolites), whereas the one-electron reduction potential (E1) of certain organochlorines is the main factor and that the E1 higher than the threshold of the reductive driving forces of DIRB probably ensures the occur of reductive dechlorination. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Study of labor accidents in the rural environment: analysis of processes and conditions of work

    Directory of Open Access Journals (Sweden)

    Thaís Alves Brito

    2009-01-01

    Full Text Available The modernization of agriculture, that broadenned the mechanization of farming and the agrotoxic use, potentially increased some risks of accidents. The agriculture workers and cattle raising are constantly exposed to several physical, chemical and biological agents, like machine, implements, handly tools, agrotoxics, ectoparaziticides, domestic animals and poisonous animals, which can to bring accidents. The aiming the importance of this working class to economic developing of country, this study was done to identify the working process and accidents that strike the rural population. This article is composed by a specialized literature review between September and December of 2007, which was made consultations to periodical and scientific articles selected through searches in the database of Scielo and Bireme. It was founded few studies related to rural workers, as well as the main articles had as setting of investigation the Southern and Southeastern, mainly in state of São Paulo and Rio Grande do Sul. In relation to work conditions was noticed a high degree of insalubrities which the workers are exposed, such as handly tools, poisonous animals, insecure attitudes because of lack of training and the no use of equipments of individual protection. There are a prevalence of accidents among men, occurring predominantly the typical accidents, the occupational disease and commute accidents. The relationships of work have been modified along the years, being the outsourcing outstanding point, however this work relationship causes legal losses to workers, which in most of the time get without social welfare right

  14. Effect of processing conditions on the interfacial zone of high performances thermoplastic composites

    International Nuclear Information System (INIS)

    Verdeau, Caroline

    1988-01-01

    This study concerns the microstructural and mechanical characterization performances thermoplastic unidirectional composites. Two semi-crystalline composites, APC2 (Peek/Carbon) and AC 40.60 (Pps/carbon) and one amorphous composite FC.PEI (PEI/Carbon) have been studied. Different processing conditions for the APC2 and AC 40.60 specimens have been employed. Amorphous matrix composites (fast cooling rates), crystalline matrix composites (slow cooling rates) and the effects of heat treatments on the matrix (lengthy hold time at the melting point followed by slow cooling) have been studied. Static test (3 points bending tests, transverse tensile tests - ±45 deg., tensile tests) allowed the different interfacial qualities to be revealed. If the fiber/matrix adhesion is excellent for APC2, it is poor for the FCPEI and AC 40.60 composites. The dynamic tests conducted on the torsion pendulum (forced oscillations; low frequencies) have shown for APC2 the existence of trans-crystallinity (mono-dimensional growth, perpendicular to the fiber surface) in the vicinity of the fiber. It has been shown that the fraction of trans-crystallinity is most important for treated specimens. In this study, an approach of the modelization of the viscoelastic behaviour of composites materials has been proposed. (author) [fr

  15. The effect of reactive ion etch (RIE) process conditions on ReRAM device performance

    Science.gov (United States)

    Beckmann, K.; Holt, J.; Olin-Ammentorp, W.; Alamgir, Z.; Van Nostrand, J.; Cady, N. C.

    2017-09-01

    The recent surge of research on resistive random access memory (ReRAM) devices has resulted in a wealth of different materials and fabrication approaches. In this work, we describe the performance implications of utilizing a reactive ion etch (RIE) based process to fabricate HfO2 based ReRAM devices, versus a more unconventional shadow mask fabrication approach. The work is the result of an effort to increase device yield and reduce individual device size. Our results show that choice of RIE etch gas (SF6 versus CF4) is critical for defining the post-etch device profile (cross-section), and for tuning the removal of metal layers used as bottom electrodes in the ReRAM device stack. We have shown that etch conditions leading to a tapered profile for the device stack cause poor electrical performance, likely due to metal re-deposition during etching, and damage to the switching layer. These devices exhibit nonlinear I-V during the low resistive state, but this could be improved to linear behavior once a near-vertical etch profile was achieved. Device stacks with vertical etch profiles also showed an increase in forming voltage, reduced switching variability and increased endurance.

  16. A comparison of facial emotion processing in neurological and psychiatric conditions

    Directory of Open Access Journals (Sweden)

    Benoit eBediou

    2012-04-01

    Full Text Available Investigating the relative severity of emotion recognition deficit across different clinical and high-risk populations has potential implications not only for the prevention, diagnosis and treatment of these diseases, but also for our understanding of the neurobiological mechanisms of emotion perception itself. We reanalyzed data from 4 studies in which we examined facial expression and gender recognition using the same tasks and stimuli. We used a standardized and bias-corrected measure of effect size (Cohen’s D to assess the extent of impairments in frontotemporal dementia (FTD, Parkinson’s disease treated by L-DOPA (PD-ON or not (PD-OFF, amnestic Mild Cognitive Impairment (aMCI, Alzheimer’s disease at mild dementia stage (AD, major depressive disorder (MDD, remitted schizophrenia (SCZ-rem, first-episode schizophrenia before (SCZ-OFF and after (SCZ-ON medication, as well as unaffected siblings of partients with schizophrenia (SIB. Analyses revealed a pattern of differential impairment of emotion (but not gender recognition, consistent with the extent of impairment of the fronto-temporal neural networks involved in the processing of faces and facial expressions. Our transnosographic approach combining clinical and high-risk populations with the impact of medication brings new information on the trajectory of impaired emotion perception in neuropsychiatric conditions, and on the neural networks and neurotransmitter systems subserving emotion perception.

  17. Light-induced magnetoresistance in solution-processed planar hybrid devices measured under ambient conditions

    Directory of Open Access Journals (Sweden)

    Sreetama Banerjee

    2017-07-01

    Full Text Available We report light-induced negative organic magnetoresistance (OMAR measured in ambient atmosphere in solution-processed 6,13-bis(triisopropylsilylethynylpentacene (TIPS-pentacene planar hybrid devices with two different device architectures. Hybrid electronic devices with trench-isolated electrodes (HED-TIE having a channel length of ca. 100 nm fabricated in this work and, for comparison, commercially available pre-structured organic field-effect transistor (OFET substrates with a channel length of 20 µm were used. The magnitude of the photocurrent as well as the magnetoresistance was found to be higher for the HED-TIE devices because of the much smaller channel length of these devices compared to the OFETs. We attribute the observed light-induced negative magnetoresistance in TIPS-pentacene to the presence of electron–hole pairs under illumination as the magnetoresistive effect scales with the photocurrent. The magnetoresistance effect was found to diminish over time under ambient conditions compared to a freshly prepared sample. We propose that the much faster degradation of the magnetoresistance effect as compared to the photocurrent was due to the incorporation of water molecules in the TIPS-pentacene film.

  18. Shield wall evaluation of hot cell facility for advanced spent fuel conditioning process

    International Nuclear Information System (INIS)

    Cho, I. J.; Kuk, D. H.; Ko, J. H.; Jung, W. M.; Yoo, G. S.; Lee, E. P.; Park, S. W.

    2002-01-01

    The future hot cell is located in the Irradiated Material Experiment Facility (IMEF) at the Korea Atomic Energy Research Institute (KAERI). It is β-γ type hot cell that was constructed on the base floor in IMEF building for irradiated material testing. And this hot cell will be used for carrying out the Advanced spent fuel Conditioning Process (ACP). The radiation shielding capability of hot cell should be sufficient to meet the radiation dose requirements in the related regulations. Because the radioactive sources of ACP are expected to be higher than radioactive sources of IMEF design criteria, the future hot cell in current status is unsatisfactory to hot test of ACP. So the shielding analysis of the future hot cell is performed to evaluate shielding ability of concrete shield wall. The shielding analysis included (a) identification of ACP source term; (b) photon source spectrum; (c) shielding analysis by QADS and MCNP-4C; and (d) enhancement of concrete shield wall. In this research, dose rates are obtained according to ACP source, geometry and hot cell shield wall thickness. And the evaluation and reinforcement thickness of the shield wall about future hot cell are concluded

  19. Monitoring and analysis of air emissions based on condition models derived from process history

    Directory of Open Access Journals (Sweden)

    M. Liukkonen

    2016-12-01

    Full Text Available Evaluation of online information on operating conditions is necessary when reducing air emissions in energy plants. In this respect, automated monitoring and control are of primary concern, particularly in biomass combustion. As monitoring of emissions in power plants is ever more challenging because of low-grade fuels and fuel mixtures, new monitoring applications are needed to extract essential information from the large amount of measurement data. The management of emissions in energy boilers lacks economically efficient, fast, and competent computational systems that could support decision-making regarding the improvement of emission efficiency. In this paper, a novel emission monitoring platform based on the self-organizing map method is presented. The system is capable, not only of visualizing the prevailing status of the process and detecting problem situations (i.e. increased emission release rates, but also of analyzing these situations automatically and presenting factors potentially affecting them. The system is demonstrated using measurement data from an industrial circulating fluidized bed boiler fired by forest residue as the primary fuel and coal as the supporting fuel.

  20. Light-induced magnetoresistance in solution-processed planar hybrid devices measured under ambient conditions.

    Science.gov (United States)

    Banerjee, Sreetama; Bülz, Daniel; Reuter, Danny; Hiller, Karla; Zahn, Dietrich R T; Salvan, Georgeta

    2017-01-01

    We report light-induced negative organic magnetoresistance (OMAR) measured in ambient atmosphere in solution-processed 6,13-bis(triisopropylsilylethynyl)pentacene (TIPS-pentacene) planar hybrid devices with two different device architectures. Hybrid electronic devices with trench-isolated electrodes (HED-TIE) having a channel length of ca. 100 nm fabricated in this work and, for comparison, commercially available pre-structured organic field-effect transistor (OFET) substrates with a channel length of 20 µm were used. The magnitude of the photocurrent as well as the magnetoresistance was found to be higher for the HED-TIE devices because of the much smaller channel length of these devices compared to the OFETs. We attribute the observed light-induced negative magnetoresistance in TIPS-pentacene to the presence of electron-hole pairs under illumination as the magnetoresistive effect scales with the photocurrent. The magnetoresistance effect was found to diminish over time under ambient conditions compared to a freshly prepared sample. We propose that the much faster degradation of the magnetoresistance effect as compared to the photocurrent was due to the incorporation of water molecules in the TIPS-pentacene film.