Surf Zone Hydrodynamics and its Utilization in Biotechnical Stabilization of Water Reservoir Banks

Directory of Open Access Journals (Sweden)

Petr Pelikán

2014-01-01

Full Text Available The water reservoir banks are eroded mainly by two factors. The first one is wave action (i.e. wave abrasion affecting the bank in direction from the reservoir. The second one is the influence of water flowing downward over the bank surface in direction from land into the reservoir (e.g. rainfall. The determination of regular altitudinal emplacement of proper designed particular biotechnical stabilization elements is the most important factor on which the right functionality of whole construction depends. Surf zone hydrodynamics solves the wave and water level changes inside the region extending from the wave breaking point to the limit of wave up-rush. The paper is focused on the utilization of piece of knowledge from a part of sea coast hydrodynamics and new approach in its application in the conditions of inland water bodies when designing the biotechnical stabilization elements along the shorelines. The “reinforced grass carpets” as a type of biotechnical method of bank stabilization are presented in the paper; whether the growth of grass root system is dependent on presence or absence of geomats in the soil structure and proceeding of their establishment on the shorelines.

Study of shifting of recombination zone in multi-emissive layer organic light emitting devices and its effect on color stability

International Nuclear Information System (INIS)

Tyagi, Priyanka; Srivastava, Ritu; Kumar, Arunandan; Tuli, Suneet; Kamalasanan, M.N.

2013-01-01

Color stability in multi-emissive layer organic light emitting devices (Me-OLEDs) has been investigated. Me-OLEDs were based on multiple emitters with a common host CBP doped with three dopants, BCzVBi, Ir(ppy) 3 and Ir(btp) 2 acac for blue, green and red emission. A major variation in CIE coordinates were found from (0.312, 0.294) to (0.236, 0.267) with increase in voltage from 6 to 9 V. This coordinate shift in Me-OLEDs has been attributed to the shifting of recombination zone with increase in voltage. In order to support our experimental observation, the EL spectrum of Me-OLEDs has been expressed as a linear combination of EL intensities of OLEDs with its individual constituting layers as emitters. In this way, the contribution of each layer in the EL spectrum of Me-OLEDs has been evaluated at each voltage. It has been observed from these calculations that the contribution of red emitter decreases from 47% to 33.33% and blue emitter increases from 38% to 51.67% with the increase in voltage from 6 to 9 V. This supports our hypothesis of shifting of recombination zone with the change in voltage. This shifting has been attributed to the field dependency of electron mobility in CBP. Me-OLED with CBP layers between the emitters was fabricated to improve the color stability. Significant improvement in color stability was achieved without changes in current efficiency in Me-OLED with interlayers. Highlights: ► Me-OLEDs have been fabricated by using three primary colors (RGB). ► CIE coordinates of these Me-OLEDs were voltage dependent. ► Analytical fitting has been performed to study the shifting of recombination zone. ► CBP interlayers have been introduced to improve the color stability. ► Color stability has been improved without any change in current efficiency

Mapping the Fluid Pathways and Permeability Barriers of a Large Gas Hydrate Reservoir

Science.gov (United States)

Campbell, A.; Zhang, Y. L.; Sun, L. F.; Saleh, R.; Pun, W.; Bellefleur, G.; Milkereit, B.

2012-12-01

An understanding of the relationship between the physical properties of gas hydrate saturated sedimentary basins aids in the detection, exploration and monitoring one of the world's upcoming energy resources. A large gas hydrate reservoir is located in the MacKenzie Delta of the Canadian Arctic and geophysical logs from the Mallik test site are available for the gas hydrate stability zone (GHSZ) between depths of approximately 850 m to 1100 m. The geophysical data sets from two neighboring boreholes at the Mallik test site are analyzed. Commonly used porosity logs, as well as nuclear magnetic resonance, compressional and Stoneley wave velocity dispersion logs are used to map zones of elevated and severely reduced porosity and permeability respectively. The lateral continuity of horizontal permeability barriers can be further understood with the aid of surface seismic modeling studies. In this integrated study, the behavior of compressional and Stoneley wave velocity dispersion and surface seismic modeling studies are used to identify the fluid pathways and permeability barriers of the gas hydrate reservoir. The results are compared with known nuclear magnetic resonance-derived permeability values. The aim of investigating this heterogeneous medium is to map the fluid pathways and the associated permeability barriers throughout the gas hydrate stability zone. This provides a framework for an understanding of the long-term dissociation of gas hydrates along vertical and horizontal pathways, and will improve the knowledge pertaining to the production of such a promising energy source.

STABILITY OF ADDITIONAL PLANETS IN AND AROUND THE HABITABLE ZONE OF THE HD 47186 PLANETARY SYSTEM

International Nuclear Information System (INIS)

Kopparapu, Ravi Kumar; Raymond, Sean N.; Barnes, Rory

2009-01-01

We study the dynamical stability of an additional, potentially habitable planet in the HD 47186 planetary system. Two planets are currently known in this system: a 'hot Neptune' with a period of 4.08 days and a Saturn-mass planet with a period of 3.7 years. Here we consider the possibility that one or more undetected planets exist between the two known planets and possibly within the habitable zone (HZ) in this system. Given the relatively low masses of the known planets, additional planets could have masses ∼ + , and hence be terrestrial-like and further improving potential habitability. We perform N-body simulations to identify the stable zone between planets b and c and find that much of the inner HZ can harbor a 10 M + planet. With the current radial velocity threshold of ∼1 m s -1 , an additional planet should be detectable if it lies at the inner edge of the habitable zone at 0.8 AU. We also show that the stable zone could contain two additional planets of 10 M + each if their eccentricities are lower than ∼0.3.

Stability Zone of Natural Gas Hydrates in a Permafrost-Bearing Region of the Beaufort-Mackenzie Basin: Study of a Feasible Energy Source (Geological Survey of Canada Contribution No.1999275)

International Nuclear Information System (INIS)

Majorowicz, J. A.; Hannigan, P. K.

2000-01-01

Analysis of geological and geophysical data from 150 wells in the Beaufort-Mackenzie region(study area between 68 deg. 30'-70 deg. 00'N and 131 deg. -39 deg. W) led to reinterpretation of the depth of methane hydrate stability and construction of the first contour maps displaying thickness of hydrate stability zones as well as hydrate stability zone thicknesses below permafrost. Calculations were based on construction of temperature-depth profiles incorporating regional heat-flow values, temperature at the base of ice-bearing permafrost, and models relating thermal conductivity with depth. Data analysis indicates the presence and extent of the methane hydrate stability zone is related mainly to the history of permafrost development and less so by the relatively small regional variations of temperature gradients. Analysis of well logs and other indicators in conjunction with knowledge of the hydrate stability zone allows reevaluation of the location of possible gas hydrate occurrences. Log analysis indicates that in the onshore and shallow sea area of the Beaufort-Mackenzie Basin, methane hydrate occurs in 27 wells. Fifteen of these locations coincides with underlying conventional hydrocarbon occurrences. Previous analyses place some of the hydrate occurrences at greater depths than proposed for the methane hydrate stability zone described in this study. Interpretation of geological cross sections reveals that hydrates are related mainly to sandy deltaic and delta-plain deposits in Iperk, Kugmallit, and Reindeer sequences although additional hydrate picks have been inferred in other sequences, such as Richards. Overlying permafrost may act as seal for hydrate accumulations; however, the thickness of permafrost and its related hydrate stability zone fluctuated during geological time. It is interpreted that only in the last tens of thousand of years (i.e., Sangamonian to Holocene), conditions for hydrates changed from nonstable to stable. During Early and Late

STABILIZING CLOUD FEEDBACK DRAMATICALLY EXPANDS THE HABITABLE ZONE OF TIDALLY LOCKED PLANETS

International Nuclear Information System (INIS)

Yang Jun; Abbot, Dorian S.; Cowan, Nicolas B.

2013-01-01

The habitable zone (HZ) is the circumstellar region where a planet can sustain surface liquid water. Searching for terrestrial planets in the HZ of nearby stars is the stated goal of ongoing and planned extrasolar planet surveys. Previous estimates of the inner edge of the HZ were based on one-dimensional radiative-convective models. The most serious limitation of these models is the inability to predict cloud behavior. Here we use global climate models with sophisticated cloud schemes to show that due to a stabilizing cloud feedback, tidally locked planets can be habitable at twice the stellar flux found by previous studies. This dramatically expands the HZ and roughly doubles the frequency of habitable planets orbiting red dwarf stars. At high stellar flux, strong convection produces thick water clouds near the substellar location that greatly increase the planetary albedo and reduce surface temperatures. Higher insolation produces stronger substellar convection and therefore higher albedo, making this phenomenon a stabilizing climate feedback. Substellar clouds also effectively block outgoing radiation from the surface, reducing or even completely reversing the thermal emission contrast between dayside and nightside. The presence of substellar water clouds and the resulting clement surface conditions will therefore be detectable with the James Webb Space Telescope.

Predictability and stability of refraction with increasing optical zone diameter in hyperopic LASIK

Directory of Open Access Journals (Sweden)

Mostafa A El-Helw

2010-05-01

Full Text Available Mostafa A El-Helw, Ahmed M EmarahCairo University, Cairo, EgyptObjective: We undertook a prospective nonrandomized study to assess refractive outcome and patient satisfaction with hyperopic laser in situ keratomileusis (LASIK using variable optical zone diameters in correction of hyperopia of more than 4.00 diopters.Methods: Fourteen adults (comprising 28 hyperopic eyes underwent hyperopic LASIK correction for hyperopia of more than 4.00 diopters. The sample was divided into two groups. Group 1 included the right eyes of the 14 patients who underwent hyperopic LASIK using a 6.5 mm optical zone diameter. Group 2 comprised the left eyes of the same patients with the only difference being that the optical zone diameter was 6.0 mm.Results: The mean age of the patients was 36.42 ± 5.10 years. Group 1 eyes had a median (range preoperative uncorrected visual acuity (UCVA of 0.79 (0.52 and best-corrected visual acuity (BCVA of 0.15 (0.08. Group 2 had a median preoperative UCVA of 0.79 (0.60 and BCVA of 0.15 (0.08. The median postoperative UCVA in Group 1 was 0.17 (0.21 and BCVA was 0.15 (0.13. In Group 2, the median postoperative UCVA was 0.30 (0.32 and BCVA was 0.15 (0.26. Group 1 had a median preoperative refraction of +5.37 (1.75 diopters and the median postoperative refraction at one week was −0.23 (1.25 diopters, at three months was +0.75 (0.75 diopters, and at six months was +0.75 (1.00 diopters. Group 2 had a median preoperative refraction of +5.00 (1.75 diopters, and the median postoperative refraction at one week was +0.13 (1.5 diopters, at three months was +1.00 (0.75 diopters and at six months +1.25 (1.25 diopters. The difference was statistically significant between groups 1 and 2. The difference within each group was also significant. Group 1 eyes were stabilizing after the three-month period in contrast with Group 2 in which the refractive changes continued throughout the follow-up period.Conclusion: Larger optical zone diameter in

Stope Stability Assessment and Effect of Horizontal to Vertical Stress Ratio on the Yielding and Relaxation Zones Around Underground Open Stopes Using Empirical and Finite Element Methods

Science.gov (United States)

Sepehri, Mohammadali; Apel, Derek; Liu, Wei

2017-09-01

Predicting the stability of open stopes can be a challenging task for underground mine engineers. For decades, the stability graph method has been used as the first step of open stope design around the world. However, there are some shortcomings with this method. For instance, the stability graph method does not account for the relaxation zones around the stopes. Another limitation of the stability graph is that this method cannot to be used to evaluate the stability of the stopes with high walls made of backfill materials. However, there are several analytical and numerical methods that can be used to overcome these limitations. In this study, both empirical and numerical methods have been used to assess the stability of an open stope located between mine levels N9225 and N9250 at Diavik diamond underground mine. It was shown that the numerical methods can be used as complementary methods along with other analytical and empirical methods to assess the stability of open stopes. A three dimensional elastoplastic finite element model was constructed using Abaqus software. In this paper a sensitivity analysis was performed to investigate the impact of the stress ratio "k" on the extent of the yielding and relaxation zones around the hangingwall and footwall of the understudy stope.

Heat flow pattern in the gas hydrate drilling areas of northern south china sea and the implication for further study

Science.gov (United States)

Wang, Lifeng; Sha, Zhibin

2015-04-01

Numerous seismic reflection profiles have been acquired by China Geological Survey (CGS) in the Northern Slope of South China Sea (SCS), clearly indicating widespread occurrence of free gases and/or gas hydrates in the sediments. In the year 2007 and 2013 respectively the gas hydrate samples are successfully recovered during two offshore drilling exploratory programs. Results of geothermal data during previous field studies along the north continental margin, however, show that the gas hydrate sites are associated with high geothermal background in contrast to the other offshore ones where the gas hydrates are more likely to be found in the low geothermal regional backgrounds. There is a common interesting heat flow pattern during the two drilling expeditions that the gas hydrate occurrences coincide with the presences of comparatively low geothermal anomalies against the high thermal background which is mainly caused by concentrated fluid upward movements into the stability zone (GHSZ) detected by the surface heat flow measurements over the studied fields. The key point for understanding the coupling between the presences of the gas hydrates and heat flow pattern at regional scale is to know the cause of high heat flows and the origin of forming gases at depth. We propose that these high heat flows are attributed to elevated shallow fault-fissure system due to the tectonic activities. A remarkable series of vertical faults and fissures are common on the upper continental slope and the forming gases are thought to have migrated with hot advective fluid flows towards seafloor mainly via fault-fissure system from underlying source rocks which are deeper levels than those of the GHSZ. The present study is based on an extensive dataset on hydrate distribution and associated temperature field measurements collected in the vicinity of studied areas during a series of field expeditions organized within the framework of national widely collaborative projects. Those

308 Building zone I stabilization and confinement

International Nuclear Information System (INIS)

Metcalf, I.L.; Schwartz, K.E.; Rich, J.W.; Benecke, M.W.; Lanham, G.W.

1994-08-01

The 308 Building located on the Hanford Site near Richland, Washington, is currently in transition to shutdown status. After this transition is complete, the facility will be maintained/surveilled and given to the U.S. Department of Energy Office of Facility Transition and Management (EM-60) for utilization, remedial action, or decontamination and decommissioning (D ampersand D). This may require that the facility be maintained in the shutdown status for as long as 30 yrs. To date, all of the special nuclear material (SNM) has been removed, potential fuel supply equipment preserved, surplus materials and equipment excessed, and enclosure cleanup and stabilization completed. A major activity in support of the 308 Building shutdown was the cleanup and stabilization of the enclosures and surface contamination areas. This document discusses the specific designs, processes, and methods used to stabilize and confine the radiological material within the enclosure and exhaust ducts to allow the shutdown of the active support systems. The process and designs employed were effective, yet simple, and maximized the use of current technologies and commercial products

Stability analysis of a heated channel cooled by supercritical water

International Nuclear Information System (INIS)

Magni, M. C.; Delmastro, D. F; Marcel, C. P

2009-01-01

A simple model to study thermal-hydraulic stability of a heated cannel under supercritical conditions is presented. Single cannel stability analysis for the SCWR (Supercritical Water Cooled Reactor) design was performed. The drastic change of fluid density in the reactor core of a SCWR may induce DWO (Density Wave Oscillations) similar to those observed in BWRs. Due to the similarities between subcritical and supercritical systems we may treat the supercritical fluid as a pseudo two-phase system. Thus, we may extend the modeling approach often used for boiling flow stability analysis to supercritical pressure operation conditions. The model developed in this work take into account three regions: a heavy fluid region, similar to an incompressible liquid; a zone where a heavy fluid and a light fluid coexist, similar to two-phase mixture; and a light fluid region which behaves like superheated steam. It was used the homogeneous equilibrium model (HEM) for the pseudo boiling zone, and the ideal gas model for the pseudo superheated steam zone. System stability maps were obtained using linear stability analysis in the frequency domain. Two possible instability mechanisms are observed: DWO and excursive Ledinegg instabilities. Also, a sensitivity analysis showed that frictions in pseudo superheated steam zone, together with acceleration effect, are the most destabilizing effects. On the other hand, frictions in pseudo liquid zone are the most important stabilizing effect. [es

Structure and properties of melt-spun high acrylonitrile copolymer fibers via continuous zone-drawing and zone-annealing processes

International Nuclear Information System (INIS)

Wu Zongquan; Zhang Anqiu; Percec, Simona; Jin Shi; Jing, Alexander J.; Ge, Jason J.; Cheng, Stephen Z.D.

2003-01-01

Continuous zone-drawing and zone-annealing processes have been utilized to probe improvements in mechanical performance of melt-spun high acrylonitrile copolymer fibers (AMLON TM ). The as-spun fibers were zone-drawn at different ratios in a narrow temperature range of 100-105 deg. C and then zone-annealed. As a result of these processes, the fibers show substantial increases in tensile strength and tensile modulus (about three times) and significant improvements in elongation-at-break (about two times) after zone annealing. The thermal transition behavior, dimensional stability and dynamic relaxation properties of the as-spun, zone-drawn and zone-annealed fibers have been studied using differential scanning calorimetry, thermal mechanical and dynamic mechanical experiments. Their mechanical and thermal property changes after the zone-drawing and zone-annealing processes can be associated with the microscopic structural evolution including crystallinity, crystal orientation and apparent crystallite size detected by wide angle X-ray diffraction experiments

Superconductor stability 90: A review

International Nuclear Information System (INIS)

Dresner, L.

1990-01-01

This paper reviews some recent developments in the field of stability of superconductors. The main topics dealt with are hydrodynamic phenomena in cable-in-conduit superconductors, namely, multiple stability, quench pressure, thermal expulsion, and thermal hydraulic quenchback, traveling normal zones in large, composite conductors, such as those intended for SMES, and the stability of vapor-cooled leads made of high-temperature superconductors. 31 refs., 5 figs

Soil moisture storage and hillslope stability

Directory of Open Access Journals (Sweden)

A. Talebi

2007-09-01

Full Text Available Recently, we presented a steady-state analytical hillslope stability model to study rain-induced shallow landslides. This model is based on kinematic wave dynamics of saturated subsurface storage and the infinite slope stability assumption. Here we apply the model to investigate the effect of neglecting the unsaturated storage on the assessment of slope stability in the steady-state hydrology. For that purpose we extend the hydrological model to compute the soil pore pressure distribution over the entire flow domain. We also apply this model for hillslopes with non-constant soil depth to compare the stability of different hillslopes and to find the critical slip surface in hillslopes with different geometric characteristics. In order to do this, we incorporate more complex approaches to compute slope stability (Janbu's non-circular method and Bishop's simplified method in the steady-state analytical hillslope stability model. We compare the safety factor (FS derived from the infinite slope stability method and the more complex approach for two cases: with and without the soil moisture profile in the unsaturated zone. We apply this extended hillslope stability model to nine characteristic hillslope types with three different profile curvatures (concave, straight, convex and three different plan shapes (convergent, parallel, divergent. Overall, we find that unsaturated zone storage does not play a critical role in determining the factor of safety for shallow and deep landslides. As a result, the effect of the unsaturated zone storage on slope stability can be neglected in the steady-state hydrology and one can assume the same bulk specific weight below and above the water table. We find that steep slopes with concave profile and convergent plan shape have the least stability. We also demonstrate that in hillslopes with non-constant soil depth (possible deep landslides, the ones with convex profiles and convergent plan shapes have

Significance of Soft Zone Sediments at the SRS

Energy Technology Data Exchange (ETDEWEB)

Aadland, R.K.

2000-02-03

The purpose of this report is to provide information on the origin, extent and stability of ''soft zones'' in the carbonate bearing strata at the Savannah River Site (SRS). As part of this study, a comprehensive historical compendium of how soft zones have been addressed during the past 47 years at SRS is reviewed.

Proportional Derivative Control with Inverse Dead-Zone for Pendulum Systems

Directory of Open Access Journals (Sweden)

José de Jesús Rubio

2013-01-01

Full Text Available A proportional derivative controller with inverse dead-zone is proposed for the control of pendulum systems. The proposed method has the characteristic that the inverse dead-zone is cancelled with the pendulum dead-zone. Asymptotic stability of the proposed technique is guaranteed by the Lyapunov analysis. Simulations of two pendulum systems show the effectiveness of the proposed technique.

Theoretical analysis of recirculation zone and buffer zone in the ADS windowless spallation target

International Nuclear Information System (INIS)

Liu, Jie; Pan, Chang-zhao; Tong, Jian-fei; Lu, Wen-qiang

2015-01-01

Highlights: • Height of recirculation zone is very important in windowless target design. • A theoretical formula for the height is derived based on the Bernoulli equation. • Numerical simulation for the LBE is performed and the height of recirculation zone is also obtained. • The theoretically-derived simulation-predicted recirculation zone heights agree with each other very well and the theoretical derivation is proved to be correct. - Abstract: The thermo-hydraulic analysis including reduction of the height of recirculation zone and stability of the free surface is very important in the design and optimization of ADS windowless spallation targets. In the present study, the Bernoulli equation is used to analyze the entire flow process in the target. Formulae for the height of the recirculation zone and the buffer zone are both obtained explicitly. Furthermore, numerical simulation for the heavy metal lead–bismuth eutectic liquid and vapor with cavitation phase change is also performed, and a novel method to calculate the height of the recirculation zone is put forward. By comparison of the theoretical formulae and numerical results, it is clearly shown that they agree with each other very well, and the heights predicted by the two methods are both determined by their own upstream flow parameters

Surface Intermediate Zone of Submerged Turbulent Buoyant Jet in Current

DEFF Research Database (Denmark)

Chen, H. B.; Larsen, Torben

1995-01-01

This paper deals with the intermediate zone between the jet and plume stages of a submerged buoyant discharge from sea outfall in current. The stability criteria, plume width and height after the intermediate zone and the dilution within the intermediate region have been studied theoretically and...

Instability Suppression in a Swirl-Stabilized Combustor Using Microjet Air Injection

KAUST Repository

LaBry, Zachary

2010-01-04

In this study, we examine the effectiveness of microjet air injection as a means of suppressing thermoacoustic instabilities in a swirl-stabilized, lean-premixed propane/air combustor. High-speed stereo PIV measurements, taken to explore the mechanism of combustion instability, reveal that the inner recirculation zone plays a dominant role in the coupling of acoustics and heat release that leads to combustion instability. Six microjet injector configurations were designed to modify the inner and outer recirculation zones with the intent of decoupling the mechanism leading to instability. Microjets that injected air into the inner recirculation zone, swirling in the opposite sense to the primary swirl were effective in suppressing combustion instability, reducing the overall sound pressure level by up to 17 dB within a certain window of operating conditions. Stabilization was achieved near an equivalence ratio of 0.65, corresponding to the region where the combustor transitions from a 40 Hz instability mode to a 110 Hz instability mode. PIV measurements made of the stabilized flow revealed significant modification of the inner recirculation zone and substantial weakening of the outer recirculation zone.

Mechanical design of multiple zone plates precision alignment apparatus for hard X-ray focusing in twenty-nanometer scale

Energy Technology Data Exchange (ETDEWEB)

Shu, Deming; Liu, Jie; Gleber, Sophie C.; Vila-Comamala, Joan; Lai, Barry; Maser, Jorg M.; Roehrig, Christian; Wojcik, Michael J.; Vogt, Franz Stefan

2017-04-04

An enhanced mechanical design of multiple zone plates precision alignment apparatus for hard x-ray focusing in a twenty-nanometer scale is provided. The precision alignment apparatus includes a zone plate alignment base frame; a plurality of zone plates; and a plurality of zone plate holders, each said zone plate holder for mounting and aligning a respective zone plate for hard x-ray focusing. At least one respective positioning stage drives and positions each respective zone plate holder. Each respective positioning stage is mounted on the zone plate alignment base frame. A respective linkage component connects each respective positioning stage and the respective zone plate holder. The zone plate alignment base frame, each zone plate holder and each linkage component is formed of a selected material for providing thermal expansion stability and positioning stability for the precision alignment apparatus.

Dredging of sand from a creek adjacent to a sand-spit for reclamation: Its impact on spit stability and coastal zone

Digital Repository Service at National Institute of Oceanography (India)

Rajagopal, M.D.; Vethamony, P.; Ilangovan, D.; Jayakumar, S.; Sudheesh, K.; Murty, K.S.R.

model to understand the flow pattern when the bathymetry is altered for dredging and (ii) GALENA to analyse the slope stability. 2. Coastal Environment of the Study Area Off Paradip, currents are of the order of 50–90 cm/s during southwest monsoon.... Assuming an average sedimentation depth of 0.5 m for a dredged area of ∼4.22 × 10 6 m 2 ,thematerial accumulated in this region (zone-I) works out to be ∼2.11×10 6 m 3 . Earlier studies proved that the mouth of JMC is a region of divergence...

Analysis of stability and adaptability of QPM hybrids of maize growing in different Colombian agroecological zones

Directory of Open Access Journals (Sweden)

Ever Andrés vargas Escobar

2016-01-01

Full Text Available Energy is maize´s biggest contribution for humans and animals. Scientist have been trying to increase its protein level since 1896, it wasn´t until the 60´s when the opaque gene O2 was discovered. In its recessive state, the gene causes the quality of the maize protein to increase, due to the growth of the Globulin protein and the reduction of Zein protein. Known as Quality Protein Maize (QPM, they can double the essential amino acids Lysine and Tryptophan´s percentages when compared with normal maize endosperm. In a commercial scenario, there is a need for high yielding genotypes adapted to different environments; it is also desirable to have a better protein quality. In the present study, 9 yellow endosperm QPM hybrids, developed by FENALCE from CIMMYT´s germoplasm and a normal commercial endosperm check were tested in 6 agro ecological zones: Wet Caribbean, Dry Caribbean, Orinoco, Valley of the Cauca River, Valley of the Magdalena River and the Coffee Growing Zone. A randomized complete block design was used in 17 environments and four repetitions. Variables concerning the plant and yield components were measured, but for this study the grain yield was the only taken. Additionally samples were taken to assess the content of Tryptophan. The stability and adaptability analysis was made using the Eberhart and Russell, Lin and Binns and AMMI models. The QPM hybrid that stood out for all the environments was QPM 303 and QPM 305 for unfavorable environments. Both retain their biochemical characteristics of protein quality and are stable in the evaluated environments according to the statistical models that were used.

Empowerment Zones and Enterprise Districts - MDC_NeighborhoodStabilizationProg

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Boundaries of Miami-Dade County's Neighborhood Stabilization Program (NSP) areas. NSP is a HUD program to provide emergency assistance to state and local governments...

CAREM-25 Steam Generator Stability Analysis

International Nuclear Information System (INIS)

Rabiti, A.; Delmastro, D.

2003-01-01

In this work the stability of a once-through CAREM-25 steam generator is analyzed.A fix nodes numerical model, that allows the modelling of the liquid, two-phase and superheated steam zones, is implemented.This model was checked against a mobile finite elements model under saturated steam conditions at the channel exit and a good agreement was obtained.Finally the stability of a CAREM steam generator is studied and the range of in let restrictions that a assure the system stability is analyzed

Development and validation of a stability-indicating capillary zone electrophoretic method for the assessment of entecavir and its correlation with liquid chromatographic methods.

Science.gov (United States)

Dalmora, Sergio Luiz; Nogueira, Daniele Rubert; D'Avila, Felipe Bianchini; Souto, Ricardo Bizogne; Leal, Diogo Paim

2011-01-01

A stability-indicating capillary zone electrophoresis (CZE) method was validated for the analysis of entecavir in pharmaceutical formulations, using nimesulide as an internal standard. A fused-silica capillary (50 µm i.d.; effective length, 40 cm) was used while being maintained at 25°C; the applied voltage was 25 kV. A background electrolyte solution consisted of a 20 mM sodium tetraborate solution at pH 10. Injections were performed using a pressure mode at 50 mbar for 5 s, with detection at 216 nm. The specificity and stability-indicating capability were proven through forced degradation studies, evaluating also the in vitro cytotoxicity test of the degraded products. The method was linear over the concentration range of 1-200 µg mL(-1) (r(2) = 0.9999), and was applied for the analysis of entecavir in tablet dosage forms. The results were correlated to those of validated conventional and fast LC methods, showing non-significant differences (p > 0.05).

Relationship between pyrite Stability and arsenic mobility during aquifer storage and recovery in southwest central Florida.

Science.gov (United States)

Jones, Gregg W; Pichler, Thomas

2007-02-01

Elevated arsenic concentrations are common in water recovered from aquifer storage and recovery (ASR) systems in west-central Florida that store surface water. Investigations of the Suwannee Limestone of the Upper Floridan aquifer, the storage zone for ASR systems, have shown that arsenic is highest in pyrite in zones of high moldic porosity. Geochemical modeling was employed to examine pyrite stability in limestone during simulated injections of surface water into wells open only to the Suwannee Limestone with known mineralogy and water chemistry. The goal was to determine if aquifer redox conditions could be altered to the degree of pyrite instability. Increasing amounts of injection water were added to native storage-zone water, and resulting reaction paths were plotted on pyrite stability diagrams. Native storage-zone water plotted within the pyrite stability field, indicating that conditions were sufficiently reducing to allow for pyrite stability. Thus, arsenic is immobilized in pyrite, and its groundwater concentration should be low. This was corroborated by analysis of water samples, none of which had arsenic concentrations above 0.036 microg/L. During simulation, however, as injection/native storage-zone water ratios increased, conditions became less reducing and pyrite became unstable. The result would be release of arsenic from limestone into storage-zone water.

EURO ZONE AND ITS MONETARY POLICY

Directory of Open Access Journals (Sweden)

Dorel Dumitru CHIRIŢESCU

2010-03-01

Full Text Available In this article I have tried to make a short presentation of the Euro Zone and it’s monetary policy. At the present moment the Euro Zone has 16 countries that have adopted the Euro as a national currency and also 4 small countries that have monetary agreements with their neighbours. The monetary policy represents all the regulations of the money supply and interest rates adopted by the European Central Bank in order to control the inflation rate and to stabilize a specific currency, in this case, the Euro. Stabilizing the inflation rate to certain levels is the main goal of the monetary policy. The monetary policy is the second policy, next to the fiscal one which in which a government, in this case the European Union’s official bodies, can impact the economic situation of the Eurozone. The fiscal policy represents the way a government spends, borrows or applies different types of taxes. The Monetary policy can be either expansionary, when unemployement and recessions needs to be combated, or contractionary, when inflation is conbated byt raising the interest rates.

Stability Enhancement of Multi machine AC Systems by Synchronverter HVDC control

Directory of Open Access Journals (Sweden)

Raouia Aouini

2016-06-01

Full Text Available This paper investigates the impact of the Synchronverter based HVDC control on power system stability. The study considers multi machine power systems, with realistic parameters. A specific tuning method of the parameters of the regulators is used. The proposed control scheme is based on the sensitivity of the poles of the HVDC neighbor zone to the control parameters, and next, on their placement using residues. The transient stability of the HVDC neighbor zone is a priori taken into account at the design stage. The new tuning method is evaluated in comparison with the standard vector control via simulation tests. Extensive tests are performed using Matlab/Simulink implementation of the IEEE 9 bus/3 machines test system. The results prove the superiority of the proposed control to the classic vector control. The synchronverter control allows to improve not only the local performances of the HVDC link, but also the overall transient stability of the AC zone in which the HVDC is inserted. (where

A Versatile Technique to Enable Sub-milli-Kelvin Instrument Stability for Precise Radial Velocity Measurements: Tests with the Habitable-zone Planet Finder

Science.gov (United States)

Stefansson, Gudmundur; Hearty, Frederick; Robertson, Paul; Mahadevan, Suvrath; Anderson, Tyler; Levi, Eric; Bender, Chad; Nelson, Matthew; Monson, Andrew; Blank, Basil; Halverson, Samuel; Henderson, Chuck; Ramsey, Lawrence; Roy, Arpita; Schwab, Christian; Terrien, Ryan

2016-12-01

Insufficient instrument thermomechanical stability is one of the many roadblocks for achieving 10 cm s-1 Doppler radial velocity precision, the precision needed to detect Earth-twins orbiting solar-type stars. Highly temperature and pressure stabilized spectrographs allow us to better calibrate out instrumental drifts, thereby helping in distinguishing instrumental noise from astrophysical stellar signals. We present the design and performance of the Environmental Control System (ECS) for the Habitable-zone Planet Finder (HPF), a high-resolution (R = 50,000) fiber-fed near-infrared (NIR) spectrograph for the 10 {{m}} Hobby-Eberly Telescope at McDonald Observatory. HPF will operate at 180 {{K}}, driven by the choice of an H2RG NIR detector array with a 1.7 μ {{m}} cutoff. This ECS has demonstrated 0.6 {mK} rms stability over 15 days at both 180 and 300 {{K}}, and maintained high-quality vacuum (\\lt {10}-7 {Torr}) over months, during long-term stability tests conducted without a planned passive thermal enclosure surrounding the vacuum chamber. This control scheme is versatile and can be applied as a blueprint to stabilize future NIR and optical high-precision Doppler instruments over a wide temperature range from ˜77 {{K}} to elevated room temperatures. A similar ECS is being implemented to stabilize NEID, the NASA/NSF NN-EXPLORE spectrograph for the 3.5 {{m}} WIYN telescope at Kitt Peak, operating at 300 {{K}}. A [full SolidWorks 3D-CAD model] and a comprehensive parts list of the HPF ECS are included with this manuscript to facilitate the adaptation of this versatile environmental control scheme in the broader astronomical community. Certain commercial equipment, instruments, or materials are identified in this paper in order to specify the experimental procedure adequately. Such identification is not intended to imply recommendation or endorsement by the National Institute of Standards and Technology, nor is it intended to imply that the materials or equipment

Origin of colour stability in blue/orange/blue stacked phosphorescent white organic light-emitting diodes

International Nuclear Information System (INIS)

Kim, Sung Hyun; Jang, Jyongsik; Yook, Kyoung Soo; Lee, Jun Yeob

2009-01-01

The origin of colour stability in phosphorescent white organic light-emitting diodes (PHWOLEDs) with a blue/orange/blue stacked emitting structure was studied by monitoring the change in a recombination zone. A balanced recombination zone shift between the blue and the orange light-emitting layers was found to be responsible for the colour stability in the blue/orange/blue stacked PHWOLEDs.

Time dependent fracture and cohesive zones

Science.gov (United States)

Knauss, W. G.

1993-01-01

This presentation is concerned with the fracture response of materials which develop cohesive or bridging zones at crack tips. Of special interest are concerns regarding crack stability as a function of the law which governs the interrelation between the displacement(s) or strain across these zones and the corresponding holding tractions. It is found that for some materials unstable crack growth can occur, even before the crack tip has experienced a critical COD or strain across the crack, while for others a critical COD will guarantee the onset of fracture. Also shown are results for a rate dependent nonlinear material model for the region inside of a craze for exploring time dependent crack propagation of rate sensitive materials.

77 FR 47558 - Extension of Border Zone in the State of New Mexico

Science.gov (United States)

2012-08-09

.... Although the border zone was intended to promote the economic stability of the border region by allowing... the economic stability of the region. On November 12, 1953, the United States and Mexico entered into... invites comments that relate to the economic, environmental, or federalism effects that might result from...

Investigating the influence of lithologic heterogeneity on gas hydrate formation and methane recycling at the base of the gas hydrate stability zone in channelized systems

Energy Technology Data Exchange (ETDEWEB)

Daigle, Hugh; Nole, Michael; Cook, Ann; Malinverno, Alberto

2017-12-14

In marine environments, gas hydrate preferentially accumulates in coarse-grained sediments. At the meso- to micro-scale, however, hydrate distribution in these coarse-grained units is often heterogeneous. We employ a methane hydrate reservoir simulator coupling heat and mass transfer as well as capillary effects to investigate how capillary controls on methane solubility affect gas and hydrate accumulations in reservoirs characterized by graded bedding and alternating sequences of coarse-grained sands and fine-grained silt and clay. Simulations bury a channelized reservoir unit encased in homogeneous, fine-grained material characterized by small pores (150 nm) and low permeability (~1 md in the absence of hydrate). Pore sizes within each reservoir bed between vary between coarse sand and fine silt. Sands have a median pore size of 35 microns and a lognormal pore size distribution. We also investigate how the amount of labile organic carbon (LOC) affects hydrate growth due to microbial methanogenesis within the sediments. In a diffusion-dominated system, methane movies into reservoir layers along spatial gradients in dissolved methane concentration. Hydrate grows in such a way as to minimize these concentration gradients by accumulating slower in finer-grained reservoir layers and faster in coarser-grained layers. Channelized, fining-upwards sediment bodies accumulate hydrate first along their outer surfaces and thence inward from top to bottom. If LOC is present in thin beds within the channel, higher saturations of hydrate will be distributed more homogeneously throughout the unit. When buried beneath the GHSZ, gas recycling can occur only if enough hydrate is present to form a connected gas phase upon dissociation. Simulations indicate that this is difficult to achieve for diffusion-dominated systems, especially those with thick GHSZs and/or small amounts of LOC. However, capillary-driven fracturing behavior may be more prevalent in settings with thick GHSZs.

Control of penetration zone GMAW

Directory of Open Access Journals (Sweden)

Віталій Петрович Iванов

2016-11-01

Full Text Available Thermal properties of the base metal, shielding medium and the nature of the electrode metal transfer to a great extent determine the penetration area formation in gas-arc welding. It is not always possible to take into account the influence of these factors on penetration front forming within the existing models. The aim of the work was to research the penetration area forming in gas-arc welding. The research of the penetration area forming in gas-arc welding of CrNi austenitic steels was made. The parameters of the regime as well as the kind of the gaseous medium influence on the formation of the penetration zone were studied. The article shows a linear proportional relationship between the electrode feed rate and the size of the base metal plate. The penetration area formation mode for welding in argon and carbon dioxide have been worked out. Diameter, feed rate and the speed of the electrode movement have been chosen as the main input parameters. Multiple regression analysis method was used to make up the modes. The relations of the third order that make it possible to take into account the electrode metal transfer and thermal properties change of the materials to be welded were used. These relationships show quite good agreement with the experimental measurements in the calculation of the fusion zone shape with consumable electrode in argon and carbon dioxide. It was determined that the shape of the melting front curve can be shown as a generalized function in which the front motion parameters depend on feed rate and the diameter of the electrode. Penetration zone growth time is determined by the welding speed and is calculated as a discrete function of the distance from the electrode with the spacing along the movement coordinate. The influence of the mode parameters on the formation of the fusion zone has been investigated and the ways to manage and stabilize the weld pool formation have been identified. The modes can be used to develop

Inside the Impossible Triangle:Monetary Policy Autonomy in a Credible Target Zone

OpenAIRE

W. Jos Jansen

2003-01-01

This paper examines the trade-off between exchange rate stability and monetary autonomy for a target zone. Using the guilder-mark target zone in the pre-EMU period as a case study, we empirically estimate how much policy discretion the Dutch central bank still enjoyed and how much had been ceded to the German central bank. The sum of these two measures is an estimate of the policy autonomy under a free float. We find that the narrow guilder-mark target zone still permitted a modest degree of ...

78 FR 35103 - Extension of Border Zone in the State of New Mexico

Science.gov (United States)

2013-06-12

..., established in 1953, was intended to promote the economic stability of the border region by allowing for freer... having to obtain a Form I-94. Although the border zone was intended to promote the economic stability of... maintain security of the border while increasing economic activity in New Mexico's border region and...

Structure and stabilization of hydrogen-rich transverse.

Energy Technology Data Exchange (ETDEWEB)

Lyra, Sgouria [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Wilde, B [Georgia Inst. of Technology, Atlanta, GA (United States); Kolla, Hemanth [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Seitzman, J. [Georgia Inst. of Technology, Atlanta, GA (United States); Lieuwen, T. C. [Georgia Inst. of Technology, Atlanta, GA (United States); Chen, Jacqueline H. [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

2014-07-01

This paper reports the results of a joint experimental and numerical study of the ow characteristics and flame stabilization of a hydrogen rich jet injected normal to a turbulent, vitiated cross ow of lean methane combustion products. Simultaneous high-speed stereoscopic PIV and OH PLIF measurements were obtained and analyzed alongside three-dimensional direct numerical simulations of inert and reacting JICF with detailed H₂/CO chemistry. Both the experiment and the simulation reveal that, contrary to most previous studies of reacting JICF stabilized in low-to-moderate temperature air cross ow, the present conditions lead to an autoigniting, burner-attached flame that initiates uniformly around the burner edge. Significant asymmetry is observed, however, between the reaction zones located on the windward and leeward sides of the jet, due to the substantially different scalar dissipation rates. The windward reaction zone is much thinner in the near field, while also exhibiting significantly higher local and global heat release than the much broader reaction zone found on the leeward side of the jet. The unsteady dynamics of the windward shear layer, which largely control the important jet/cross flow mixing processes in that region, are explored in order to elucidate the important flow stability implications arising in the reacting JICF. Vorticity spectra extracted from the windward shear layer reveal that the reacting jet is globally unstable and features two high frequency peaks, including a fundamental mode whose Strouhal number of ~0.7 agrees well with previous non-reacting JICF stability studies. The paper concludes with an analysis of the ignition, ame stabilization, and global structure of the burner-attached flame. Chemical explosive mode analysis (CEMA) shows that the entire windward shear layer, and a large region on the leeward side of the jet, are highly explosive prior to ignition and are dominated by non-premixed flame structures after

Foam - novel delivery technology for remediation of vadose zone environments - 59019

International Nuclear Information System (INIS)

Jansik, Danielle; Wellman, Dawn M.; Mattigod, Shas V.; Zhong, Lirong; Zhang, Fred; Foote, Martin; Wu, Yuxin; Hubbard, Susan

2012-01-01

Deep vadose zone environments can be a primary source and pathway for contaminant migration to groundwater. These environments present unique characterization and remediation challenges that necessitate scrutiny and research. The thickness, depth, and intricacies of the deep vadose zone, combined with a lack of understanding of the key subsurface processes (e.g., biogeochemical and hydrologic) affecting contaminant migration, make it difficult to create validated conceptual and predictive models of subsurface flow dynamics and contaminant behavior across multiple scales. These factors also make it difficult to design and deploy sustainable remedial approaches and monitor long-term contaminant behavior after remedial actions. Functionally, methods for addressing contamination must remove and/or reduce transport of contaminants. This problem is particularly challenging in the arid western United States where the vadose zone is hundreds of feet thick, rendering transitional excavation methods exceedingly costly and ineffective. Delivery of remedial amendments is one of the most challenging and critical aspects for all remedy-based approaches. The conventional approach for delivery is through injection of aqueous remedial solutions. However, heterogeneous deep vadose zone environments present hydrologic and geochemical challenges that limit the effectiveness. Because the flow of solution infiltration is dominantly controlled by gravity and suction, injected liquid preferentially percolates through highly permeable pathways, by-passing low-permeability zones that frequently contain the majority of contamination. Moreover, the wetting front can readily mobilize and enhance contaminant transport to the underlying aquifer prior to stabilization. Development of innovative in-situ technologies may be the only means to meet remedial action objectives and long-term stewardship goals. Surfactants can be used to lower the liquid surface tension and create stabile foams, which

Effects of Vojta method on trunk stability in healthy individuals.

Science.gov (United States)

Ha, Sun-Young; Sung, Yun-Hee

2016-12-01

Vojta reflex locomotion is important to main upright posture through stimulation of breast zone to patient with cerebral palsy. However, application in other diseases is no investigated. So, we determined the effects of stimulation of the breast zone on trunk stability in healthy individuals. Fourteen young healthy adults (7 males and 7 females) voluntarily participated in this study. The subjects were randomly divided into an experimental group (breast zone) and control group (arbitrary point). All groups were stimulated for 5 min on the left and right sides, respectively, for a total 10 times. We used the thickness of the external oblique abdominal muscle (EO), the internal oblique abdominal muscle, the transversus abdominis muscle (TrA), and the rectus abdominis muscles, as well as the area of the diaphragm by using ultrasonography. In the experimental group, the thickness of the TrA significantly increased during stimulation ( P <0.05) while the thickness of the EO significantly decreased ( P <0.05). Also, the area of diaphragm in inspiration was significantly different ( P <0.05). Therefore, stimulation of the breast zone may be effective to improve trunk stability through activation of the TrA muscle and the diaphragm.

Are high oil prices a threat for the price stability?

International Nuclear Information System (INIS)

Mollerus, A.

2000-01-01

The high price for oil and the decreased value of the Euro increase the risks for the stability of prices. Still, the prospects for inflation are favorable for the Euro zone. Less favorable are the consequences for the Netherlands, while the inflation difference with the Euro zone appears to become bigger, in particular as a result of the new Tax regulations in the Netherlands

Stabilization and structure of N-heptane flame on CWJ-spray burner with kHZ SPIV and OH-PLIF

KAUST Repository

Mansour, Morkous S.

2015-08-31

A curved wall-jet (CWJ) burner was employed to stabilize turbulent spray flames that utilized a Coanda effect by supplying air as annular-inward jet over a curved surface, surrounding an axisymmetric solid cone fuel spray. The stabilization characteristics and structure of n-heptane/air turbulent flames were investigated with varying fuel and air flow rates and the position of pressure atomizer (L). High-speed planar laser-induced fluorescence (PLIF) of OH radicals delineated reaction zone contours and simultaneously stereoscopic particle image velocimetry (SPIV) quantified the flow field features, involving turbulent mixing within spray, ambient air entrainment and flame-turbulence interaction. High turbulent rms velocities were generated within the recirculation zone, which improved the flame stabilization. OH fluorescence signals revealed a double flame structure near the stabilization edge of lifted flame that consisted of inner partially premixed flame and outer diffusion flame front. The inner reaction zone is highly wrinkled and folded due to significant turbulent mixing between the annular-air jet and the fuel vapor generated from droplets along the contact interface of this air jet with the fuel spray. Larger droplets, having higher momentum are able to penetrate the inner reaction zone and then vaporized in the low-speed hot region bounded by these reaction zones; this supports the outer diffusion flame. Frequent local extinctions in the inner reaction zone were observed at low air flow rate. As flow rate increases, the inner zone is more resistant to local extinction despite of its high wrinkling and corrugation degree. However, the outer reaction zone exhibits stable and mildly wrinkled features irrespective of air flow rate. The liftoff height increases with the air mass flow rate but decreases with L.

Characteristics of premixed flames stabilized in an axisymmetric curved-wall jet burner with tip modification

KAUST Repository

Kim, Daejoong

2009-11-10

The stabilization characteristics of premixed flames in an axisymmetric curved-wall jet burner have been experimentally investigated. This burner utilized the Coanda effect on top of a burner tip. The initially spherical burner tip was modified to a flat tip and a concave tip in order to improve flame stabilization by providing enough space for flow recirculation above the burner tip region. The flow characteristics have been visualized using a schlieren technique. Small-scale turbulence structure has been observed mainly in the interaction jet region (located downstream of the recirculation region) for large jet velocity (Reynolds number >11,500). An appreciable amount of air entrainment was exhibited from the half-angle of the jet spread, approximately 20. The averaged planar laser-induced fluorescence images of the flames for this large velocity demonstrated that the strong signal of OH radicals, representing reaction zones, existed in the recirculation zone, while it was weak in the interaction jet region due to intermittency and local extinction by the generation of small scale turbulence. The OH radical signals strengthened again in the merged jet region (downstream of the interaction jet region). In extreme cases of Reynolds number over 19,000, a unique flame exhibiting OH radicals only in the recirculation zone was observed for the concave tip. The flame stabilization has been mapped by varying jet velocity and equivalence ratio, and the result showed that the stabilization characteristics were improved appreciably from the initial spherical tip design, especially for rich mixtures. The flow fields measured by a laser Doppler velocimetry confirmed the existence of recirculation zone and the expansion of the recirculation zones for the modified tips. The temperature profile measured by a coherent anti-Stokes Raman spectroscopy exhibited an intermittent nature, especially near the recirculation zone.

Analysis of the stability of underground high-level nuclear waste repository in discontinuous rock mass using 3DEC

International Nuclear Information System (INIS)

Kwon, Sang Ki; Park, Jeong Hwa; Choi, Jong Won; Kang, Chul Hyung

2001-03-01

For the safe design of a high-level nuclear waste repository in deep location, it is necessary to confirm the stability of the underground excavations under the high overburden pressure and also to investigate the influence of discontinuities such as fault, fracture zone, and joints. In this study, computer simulations using 3DEC, which is a Distince Element (DEM) code, were carried out for determining important parameters on the stability of the disposal tunnel and deposition holes excavated in 500 m deep granite body. The development of plastic zone and stress and strain distributions were analyzed with various modelling conditions with variation on the parameters including joint numbers, tunnel size, joint properties, rock properties, and stress ratio. Furthermore, the influence of fracture zone, which is located around the underground excavations, on the stability of the excavation was investigated. In this study, the variation of stress and strain distribution due to the variation of fracture zone location, dip, and width was analyzed

Generalized projective chaos synchronization of gyroscope systems subjected to dead-zone nonlinear inputs

International Nuclear Information System (INIS)

Yau, H.-T.

2008-01-01

This Letter presents a robust control scheme to generalized projective synchronization between two identical two-degrees-of-freedom heavy symmetric gyroscopes with dead zone nonlinear inputs. Because of the nonlinear terms of the gyroscope system, the system exhibits complex and chaotic motions. By the Lyapunov stability theory with control terms, two suitable sliding surfaces are proposed to ensure the stability of the controlled closed-loop system in sliding mode. Then, two sliding mode controllers (SMC) are designed to guarantee the hitting of the sliding surfaces even when the control inputs contain dead-zone nonlinearity. This method allows us to arbitrarily direct the scaling factor onto a desired value. Numerical simulations show that this method works very well for the proposed controller

Trace Metals in Groundwater and the Vadose Zone Calcite: In Situ Containment and Stabilization of Strontium-90 and Other Divalent Metals and Radionuclides at Arid West DOE

International Nuclear Information System (INIS)

Smith, Robert W.

2004-01-01

Radionuclide and metal contaminants such as strontium-90 are present beneath U.S. Department of Energy (DOE) lands in both the groundwater (e.g., 100-N area at Hanford, WA) and vadose zone (e.g., Idaho Nuclear Technology and Engineering Center at the Idaho National Engineering and Environmental Laboratory). In situ containment and stabilization of these contaminants is a cost-effective treatment strategy. However, implementing in situ containment and stabilization approaches requires definition of the mechanisms that control contaminant sequestration. We are investigating the in situ immobilization of radionuclides or contaminant metals (e.g., strontium-90) by their facilitated co-precipitation with calcium carbonate in groundwater and vadose zone systems. Our facilitated approach, shown schematically in Figure 1, relies upon the hydrolysis of introduced urea to cause the acceleration of calcium carbonate precipitation (and trace metal co-precipitation) by increasing pH and alkalinity. Subsurface urea hydrolysis is catalyzed by the urease enzyme, which may be either introduced with the urea or produced in situ by ubiquitous subsurface urea hydrolyzing microorganisms. Because the precipitation process tends to be irreversible and many western aquifers are saturated with respect to calcite, the co-precipitated metals and radionuclides will be effectively removed from the aqueous phase over the long-term. Another advantage of the ureolysis approach is that the ammonium ions produced by the reaction can exchange with radionuclides sorbed to subsurface minerals, thereby enhancing the availability of the radionuclides for re-capture in a more stable solid phase (co-precipitation rather than adsorption)

Soft zone formation in dissimilar welds between two Cr-Mo steels

International Nuclear Information System (INIS)

Albert, S.K.; Gill, T.P.S.; Tyagi, A.K.; Mannan, S.L.; Rodriguez, P.; Kulkarni, S.D.

1997-01-01

Two dissimilar weldments between 9Cr-1Mo and 2.25Cr-1Mo ferritic steels have been characterized for their microstructural stability during various postweld heat treatments (PWHTs). The samples for the investigation were extracted from bead-on-plate weldments made by depositing 2.25Cr-1Mo weld metal on 9Cr-1Mo base plate and vice versa. Subsequent application of PWHT resulted in the formation of a soft zone in the low Cr ferritic steel weld or base plate. A carbide-rich hard zone, adjoining the soft zone, was also detected in the high Cr side of the weldment. Unmixed zones in the weld metal provided additional soft and hard zones in the weld metals. The migration of carbon from low-Cr steel to high-Cr steel, driven by the carbon activity gradient, has been shown to be responsible for the formation of soft and hard zones. A carbon activity diagram for 2.25Cr-1Mo/9Cr-1Mo weldments has been proposed to aid in the selection of welding consumables for reducing or preventing the soft zone formation

Equipment for manufacture of single crystals by zone overlaying

International Nuclear Information System (INIS)

Richter, O.

1981-01-01

The patented heater element for the manufacture of monocrystals by zone melting of layers consists of a heated pipe with insert slipped onto the heated pipe or consisting, in turn, of pieces fixed parallel to the heated pipe or a piece placed between two pipes. The insert is designed for stabilizing the melt surface. (Ha)

Early structure of LPG partially premixed conically stabilized flames

KAUST Repository

Elbaz, Ayman M.

2013-01-01

This paper presents experimental investigation of LPG partially premixed turbulent flames stabilized within a conical nozzle burner under constant degree of partial premixing. The stability limits and mean flame structure are presented based on the mean gas temperature and the concentration of CO, O 2, NO, and HC at the flame early region of reaction. The investigation covered the influence of the nozzle cone angle, the jet exit velocity and the jet equivalence ratio. The stability results show that the flames with cone are more stable than those without cone. For conical stabilized flames, the stability results exhibit three different sensitivity regions between the jet velocity and equivalence ratio. The inflame measurements prove that the flame stability could be attributed to the triple flame structure at the flame leading edge. The data show that the triple flame structure is influenced by cone angle, the jet velocity and the equivalence ratio. The flame is believed to be controlled by the recirculation flow inside the cone. Increasing the cone angle induced higher air entrainment to the reaction zone as depicted by a higher O 2 concentration within the flame leading edge. Increasing the jet velocity to a certain limit enhances the intensity of combustion at the flame leading edge, while excessive increase in jet velocity reduces this intensity. At a fixed jet velocity the higher the equivalence ratio, the higher the amount of fuel diffused and engulfed to the reaction zone, the more delay of the combustion completion and the higher the emission concentrations of the flame. © 2012 Elsevier Inc.

Effect of adding a swirl on flow pattern and recirculation zone in ADS windowless spallation target

Energy Technology Data Exchange (ETDEWEB)

Liu, Jie, E-mail: nauty@ucas.ac.cn [School of Physics, University of Chinese Academy of Sciences, Beijing (China); Gao, Lei [School of Physics, University of Chinese Academy of Sciences, Beijing (China); Yang, Lei [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou (China); Lu, Wen-qiang [School of Physics, University of Chinese Academy of Sciences, Beijing (China)

2014-09-15

Highlights: • The reduction of the recirculation zone and the stability of the free surface are key issues in the target. • A swirl is numerically added in the target to make the recirculation zone small and stable. • Numerical simulation with different boundary conditions is carried out. • Physical analysis is presented to explain the numerical results. - Abstract: Aiming the key issues in the accelerator driven system (ADS), windowless spallation target focus on the minimization of the recirculation zone and on the stability of the free surface, an innovation has been made by numerically adding swirl to the fluid at the inlet. At first, two phase flow pattern in the simulation is compared with the experiments and numerical method is employed correctly. The results reveal that the recirculation zone and the flow pattern are greatly influenced when the swirl strength is changed from 1.0 rad/s to 2.5 rad/s. The height of the recirculation zone decreases with increase in swirl strength and completely disappears when the swirl strength reaches 2.0 rad/s. In addition, larger swirl strength leads to different flow pattern and a new cavitation zone is generated under the recirculation zone. The Bernoulli's equation and angular momentum conservation are applied to make it clear that this phenomena is due to the decrease of the axial pressure caused by the radial velocity. Moreover, the new cavitation zone totally links to the vapor area above the recirculation zone when the swirl strength is 2.5 rad/s. The results are very helpful to the design and optimization of the ADS windowless spallation target.

Effect of adding a swirl on flow pattern and recirculation zone in ADS windowless spallation target

International Nuclear Information System (INIS)

Liu, Jie; Gao, Lei; Yang, Lei; Lu, Wen-qiang

2014-01-01

Highlights: • The reduction of the recirculation zone and the stability of the free surface are key issues in the target. • A swirl is numerically added in the target to make the recirculation zone small and stable. • Numerical simulation with different boundary conditions is carried out. • Physical analysis is presented to explain the numerical results. - Abstract: Aiming the key issues in the accelerator driven system (ADS), windowless spallation target focus on the minimization of the recirculation zone and on the stability of the free surface, an innovation has been made by numerically adding swirl to the fluid at the inlet. At first, two phase flow pattern in the simulation is compared with the experiments and numerical method is employed correctly. The results reveal that the recirculation zone and the flow pattern are greatly influenced when the swirl strength is changed from 1.0 rad/s to 2.5 rad/s. The height of the recirculation zone decreases with increase in swirl strength and completely disappears when the swirl strength reaches 2.0 rad/s. In addition, larger swirl strength leads to different flow pattern and a new cavitation zone is generated under the recirculation zone. The Bernoulli's equation and angular momentum conservation are applied to make it clear that this phenomena is due to the decrease of the axial pressure caused by the radial velocity. Moreover, the new cavitation zone totally links to the vapor area above the recirculation zone when the swirl strength is 2.5 rad/s. The results are very helpful to the design and optimization of the ADS windowless spallation target

A Dynamic Hydrology-Critical Zone Framework for Rainfall-triggered Landslide Hazard Prediction

Science.gov (United States)

Dialynas, Y. G.; Foufoula-Georgiou, E.; Dietrich, W. E.; Bras, R. L.

2017-12-01

Watershed-scale coupled hydrologic-stability models are still in their early stages, and are characterized by important limitations: (a) either they assume steady-state or quasi-dynamic watershed hydrology, or (b) they simulate landslide occurrence based on a simple one-dimensional stability criterion. Here we develop a three-dimensional landslide prediction framework, based on a coupled hydrologic-slope stability model and incorporation of the influence of deep critical zone processes (i.e., flow through weathered bedrock and exfiltration to the colluvium) for more accurate prediction of the timing, location, and extent of landslides. Specifically, a watershed-scale slope stability model that systematically accounts for the contribution of driving and resisting forces in three-dimensional hillslope segments was coupled with a spatially-explicit and physically-based hydrologic model. The landslide prediction framework considers critical zone processes and structure, and explicitly accounts for the spatial heterogeneity of surface and subsurface properties that control slope stability, including soil and weathered bedrock hydrological and mechanical characteristics, vegetation, and slope morphology. To test performance, the model was applied in landslide-prone sites in the US, the hydrology of which has been extensively studied. Results showed that both rainfall infiltration in the soil and groundwater exfiltration exert a strong control on the timing and magnitude of landslide occurrence. We demonstrate the extent to which three-dimensional slope destabilizing factors, which are modulated by dynamic hydrologic conditions in the soil-bedrock column, control landslide initiation at the watershed scale.

76 FR 37763 - Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Cod Allocations in the Gulf of...

Science.gov (United States)

2011-06-28

...-AY53 Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Cod Allocations in the Gulf of Alaska... the uncertainty regarding the distribution of Pacific cod catch, enhance stability among the sectors... available for public review and comment. The groundfish fisheries in the exclusive economic zone of the Gulf...

X-ray microscopy with high resolution zone plates -- Recent developments

International Nuclear Information System (INIS)

Schneider, G.; Wilhein, T.; Niemann, B.; Guttmann, P.

1995-01-01

In order to expand the applications of X-ray microscopy, developments in the fields of zone plate technology, specimen preparation and imaging techniques have been made. A new cross-linked polymer chain electron beam resist allows to record zone plate pattern down to 19 nm outermost zone width. High resolution zone plates in germanium with outermost zone widths down to 19 nm have been developed. In addition, phase zone plates in nickel down to 30 nm zone width have been made by electroplating. In order to enhance the image contrast for weak absorbing objects, the phase contrast method for X-ray microscopy was developed and implemented on the Goettingen X-ray microscope at BESSY. The effects of X-ray absorption on the structure of biological specimen limits the maximum applicable radiation dose and therefore the achievable signal to noise ratio for an artifact-free X-ray image. To improve the stability especially of biological specimen, a cryogenic object chamber has been developed and tested. It turns out that at the operating temperature T ≤ 130 K unfixed biological specimen can be exposed to a radiation dose of 10 9 --10 10 Gy without any observable structural changes. A multiple-angle viewing stage allows to take stereoscopic images with the X-ray microscope, giving a 3D-impression of the object

Vertical ascending electrophoresis of cells with a minimal stabilizing medium

Science.gov (United States)

Omenyi, S. N.; Snyder, R. S.

1983-01-01

Vertical fractionation of a mixture of fixed horse and human red blood cells layered over a stabilizing support medium was done to give a valid comparison with proposed space experiments. In particular, the effects of sample thickness and concentration on zone migration rate were investigated. Electrophoretic mobilities of horse and human cells calculated from zone migration rates were compatible with those obtained by microelectrophoresis. Complete cell separation was observed when low power and effective cooling were employed.

76 FR 44699 - Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Cod Allocations in the Gulf of...

Science.gov (United States)

2011-07-26

... Atmospheric Administration 50 CFR Parts 679 and 680 Fisheries of the Exclusive Economic Zone Off Alaska... 0648-AY53 Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Cod Allocations in the Gulf of... competition among sectors and support stability in the Pacific cod fishery. This rule would also limit access...

The blow-off mechanism of a bluff-body stabilized laminar premixed flame

KAUST Repository

Kedia, Kushal S.

2015-04-01

© 2014 The Combustion Institute. The objective of this work is to investigate the dynamics leading to blow-off of a laminar premixed flame stabilized on a confined bluff-body using high fidelity numerical simulations. We used unsteady, fully resolved, two-dimensional simulations with detailed chemical kinetics and species transport for methane-air combustion. The flame-wall interaction between the hot reactants and the heat conducting bluff-body was accurately captured by incorporating the conjugate heat exchange between them. Simulations showed a shear-layer stabilized flame just downstream of the bluff-body, with a recirculation zone formed by the products of combustion. The flame was negatively stretched along its entire length, primarily dominated by the normal component of the strain. Blow-off was approached by decreasing the mixture equivalence ratio, at a fixed Reynolds number, of the incoming flow. A flame is stable (does not undergo blow-off) when (1) flame displacement speed is equal to the flow speed and (2) the gradient of the flame displacement speed normal to its surface is higher than the gradient of the flow speed along the same direction. As the equivalence ratio is reduced, the difference between the former and the latter shrinks until the dynamic stability condition (2) is violated, leading to blow-off. Blow-off initiates at a location where this is first violated along the flame. Our results showed that this location was far downstream from the flame anchoring zone, near the end of the recirculation zone. Blow-off started by flame pinching separating the flame into an upstream moving (carried within the recirculation zone) and a downstream convecting (detached from the recirculation zone) flame piece. Within the range of operating conditions investigated, the conjugate heat exchange with the bluff-body had no impact on the flame blow-off.

Improving Keyhole Stability by External Magnetic Field in Full Penetration Laser Welding

Science.gov (United States)

Li, Min; Xu, Jiajun; Huang, Yu; Rong, Youmin

2018-05-01

An external magnetic field was used to improve the keyhole stability in full penetration laser welding 316L steel. The increase of magnetic field strength gave rise to a shorter flying time of the spatter, a weaker size and brightness of the spatter, and a larger spreading area of vapor plume. This suggested that the dynamic behavior of the keyhole was stabilized by the external magnetic field. In addition, a stronger magnetic field could result in a more homogeneous distribution of laser energy, which increased the width of the weld zone, and the height of the bottom weld zone from 381 μm (0 mT) to 605 μm (50 mT). Dendrite and cellular crystal near the weld center disappeared, and grain size was refined. The external magnetic field was beneficial to the keyhole stability and improved the joint quality, because the weld pool was stirred by a Lorentz force resulting from the coupling effect of the magnetic field and inner thermocurrent.

Prospects for a nuclear-weapon-free zone in Central Asia

International Nuclear Information System (INIS)

Potter, W.C.

1997-01-01

This paper examines the concept of a Nuclear-Weapon-Free Zone (NWFZ) as an approach to nuclear nonproliferation with special reference to Central Asia . 20 More specifically, it describes the evolution of a NWFZ in the region, the potential benefits of a zone, the principal obstacles in the path of its implementation, and the practical steps that need to be taken if a NWFZ in Central Asia is to be realized. The paper concludes that a NWFZ in Central Asia, as with prior NWFZ, would likely lead to advances in the application of an important nonproliferation approach. One innovative aspect of the zone in Central Asia might be its treatment of environmental issues. Although it will not be a simple process to rally support from all of the P-5 states for a new NWFZ, all countries of Central Asia - as well as global community of nations - should profit from creation of a zone which reinforces the international nonproliferation regime improves prospects for political and economic stability in a region of growing importance

Monitoring well utility in a heterogeneous DNAPL source zone area: Insights from proximal multilevel sampler wells and sampling capture-zone modelling.

Science.gov (United States)

McMillan, Lindsay A; Rivett, Michael O; Wealthall, Gary P; Zeeb, Peter; Dumble, Peter

2018-03-01

Groundwater-quality assessment at contaminated sites often involves the use of short-screen (1.5 to 3 m) monitoring wells. However, even over these intervals considerable variation may occur in contaminant concentrations in groundwater adjacent to the well screen. This is especially true in heterogeneous dense non-aqueous phase liquid (DNAPL) source zones, where cm-scale contamination variability may call into question the effectiveness of monitoring wells to deliver representative data. The utility of monitoring wells in such settings is evaluated by reference to high-resolution multilevel sampler (MLS) wells located proximally to short-screen wells, together with sampling capture-zone modelling to explore controls upon well sample provenance and sensitivity to monitoring protocols. Field data are analysed from the highly instrumented SABRE research site that contained an old trichloroethene source zone within a shallow alluvial aquifer at a UK industrial facility. With increased purging, monitoring-well samples tend to a flow-weighted average concentration but may exhibit sensitivity to the implemented protocol and degree of purging. Formation heterogeneity adjacent to the well-screen particularly, alongside pump-intake position and water level, influence this sensitivity. Purging of low volumes is vulnerable to poor reproducibility arising from concentration variability predicted over the initial 1 to 2 screen volumes purged. Marked heterogeneity may also result in limited long-term sample concentration stabilization. Development of bespoke monitoring protocols, that consider screen volumes purged, alongside water-quality indicator parameter stabilization, is recommended to validate and reduce uncertainty when interpreting monitoring-well data within source zone areas. Generalised recommendations on monitoring well based protocols are also developed. A key monitoring well utility is their proportionately greater sample draw from permeable horizons constituting

Monitoring well utility in a heterogeneous DNAPL source zone area: Insights from proximal multilevel sampler wells and sampling capture-zone modelling

Science.gov (United States)

McMillan, Lindsay A.; Rivett, Michael O.; Wealthall, Gary P.; Zeeb, Peter; Dumble, Peter

2018-03-01

Groundwater-quality assessment at contaminated sites often involves the use of short-screen (1.5 to 3 m) monitoring wells. However, even over these intervals considerable variation may occur in contaminant concentrations in groundwater adjacent to the well screen. This is especially true in heterogeneous dense non-aqueous phase liquid (DNAPL) source zones, where cm-scale contamination variability may call into question the effectiveness of monitoring wells to deliver representative data. The utility of monitoring wells in such settings is evaluated by reference to high-resolution multilevel sampler (MLS) wells located proximally to short-screen wells, together with sampling capture-zone modelling to explore controls upon well sample provenance and sensitivity to monitoring protocols. Field data are analysed from the highly instrumented SABRE research site that contained an old trichloroethene source zone within a shallow alluvial aquifer at a UK industrial facility. With increased purging, monitoring-well samples tend to a flow-weighted average concentration but may exhibit sensitivity to the implemented protocol and degree of purging. Formation heterogeneity adjacent to the well-screen particularly, alongside pump-intake position and water level, influence this sensitivity. Purging of low volumes is vulnerable to poor reproducibility arising from concentration variability predicted over the initial 1 to 2 screen volumes purged. Marked heterogeneity may also result in limited long-term sample concentration stabilization. Development of bespoke monitoring protocols, that consider screen volumes purged, alongside water-quality indicator parameter stabilization, is recommended to validate and reduce uncertainty when interpreting monitoring-well data within source zone areas. Generalised recommendations on monitoring well based protocols are also developed. A key monitoring well utility is their proportionately greater sample draw from permeable horizons constituting a

Multiple-Time-Scales Hierarchical Frequency Stability Control Strategy of Medium-Voltage Isolated Microgrid

DEFF Research Database (Denmark)

Zhao, Zhuoli; Yang, Ping; Guerrero, Josep M.

2016-01-01

In this paper, an islanded medium-voltage (MV) microgrid placed in Dongao Island is presented, which integrates renewable-energy-based distributed generations (DGs), energy storage system (ESS), and local loads. In an isolated microgrid without connection to the main grid to support the frequency......, it is more complex to control and manage. Thus in order to maintain the frequency stability in multiple-time-scales, a hierarchical control strategy is proposed. The proposed control architecture divides the system frequency in three zones: (A) stable zone, (B) precautionary zone and (C) emergency zone...... of Zone B. Theoretical analysis, time-domain simulation and field test results under various conditions and scenarios in the Dongao Island microgrid are presented to prove the validity of the introduced control strategy....

A dynamical stabilizer in the climate system: a mechanism suggested by a simple model

Science.gov (United States)

Bates, J. R.

1999-05-01

A simple zonally averaged hemispheric model of the climate system is constructed, based on energy equations for two ocean basins separated at 30° latitude with the surface fluxes calculated explicitly. A combination of empirical input and theoretical calculation is used to determine an annual mean equilibrium climate for the model and to study its stability with respect to small perturbations. The insolation, the mean albedos and the equilibrium temperatures for the two model zones are prescribed from observation. The principal agent of interaction between the zones is the vertically integrated poleward transport of atmospheric angular momentum across their common boundary. This is parameterized using an empirical formula derived from a multiyear atmospheric data set. The surface winds are derived from the angular momentum transport assuming the atmosphere to be in a state of dynamic balance on the climatic timescales of interest. A further assumption that the air sea temperature difference and low level relative humidity remain fixed at their mean observed values then allows the surface fluxes of latent and sensible heat to be calculated. Results from a radiative model, which show a positive lower tropospheric water vapour/infrared radiative feedback on SST perturbations in both zones, are used to calculate the net upward infrared radiative fluxes at the surface. In the model's equilibrium climate, the principal processes balancing the solar radiation absorbed at the surface are evaporation in the tropical zone and net infrared radiation in the extratropical zone. The stability of small perturbations about the equilibrium is studied using a linearized form of the ocean energy equations. Ice-albedo and cloud feedbacks are omitted and attention is focussed on the competing effects of the water vapour/infrared radiative feedback and the turbulent surface flux and oceanic heat transport feedbacks associated with the angular momentum cycle. The perturbation equations

Overview of waste stabilization with cement.

Science.gov (United States)

Batchelor, B

2006-01-01

Cement can treat a variety of wastes by improving physical characteristics (solidification) and reducing the toxicity and mobility of contaminants (stabilization). Potentially adverse waste-binder interactions are an important consideration because they can limit solidification. Stabilization occurs when a contaminant is converted from the dissolved (mobile) phase to a solid (immobile) phase by reactions, such as precipitation, sorption, or substitution. These reactions are often strongly affected by pH, so the presence of components of the waste that control pH are critical to stabilization reactions. Evaluating environmental impacts can be accomplished in a tiered strategy in which simplest approach would be to measure the maximum amount of contaminant that could be released. Alternatively, the sequence of release can be determined, either by microcosm tests that attempt to simulate conditions in the disposal zone or by mechanistic models that attempt to predict behavior using fundamental characteristics of the treated waste.

ArthroBroström Lateral Ankle Stabilization Technique: An Anatomic Study.

Science.gov (United States)

Acevedo, Jorge I; Ortiz, Cristian; Golano, Pau; Nery, Caio

2015-10-01

Arthroscopic ankle lateral ligament repair techniques have recently been developed and biomechanically as well as clinically validated. Although there has been 1 anatomic study relating suture and anchor proximity to anatomic structures, none has evaluated the ArthroBroström procedure. To evaluate the proximity of anatomic structures for the ArthroBroström lateral ankle ligament stabilization technique and to define ideal landmarks and "safe zones" for this repair. Descriptive laboratory study. Ten human cadaveric ankle specimens (5 matched pairs) were screened for the study. All specimens underwent arthroscopic lateral ligament repair according to the previously described ArthroBroström technique with 2 suture anchors in the fibula. Three cadaveric specimens were used to test the protocol, and 7 were dissected to determine the proximity of anatomic structures. Several distances were measured, including those of different anatomic structures to the suture knots, to determine the "safe zones." Measurements were obtained by 2 separate observers, and statistical analysis was performed. None of the specimens revealed entrapment by either of the suture knots of the critical anatomic structures, including the superficial peroneal nerve (SPN), sural nerve, peroneus tertius tendon, peroneus brevis tendon, or peroneus longus tendon. The internervous safe zone between the intermediate branch of the SPN and sural nerve was a mean of 51 mm (range, 39-64 mm). The intertendinous safe zone between the peroneus tertius and peroneus brevis was a mean of 43 mm (range, 37-49 mm). On average, a 20-mm (range, 8-36 mm) safe distance was maintained from the most medial suture to the intermediate branch of the SPN. The amount of inferior extensor retinaculum (IER) grasped by either suture knot varied from 0 to 12 mm, with 86% of repairs including the retinaculum. The results indicate that there is a relatively wide internervous and intertendinous safe zone when performing the Arthro

Stability of infant and child feeding index over time and its association with nutritional status of HIV exposed infants in Sidama Zone, Southern Ethiopia: a longitudinal study.

Science.gov (United States)

Haile, Demewoz; Belachew, Tefera; Berhanu, Getenesh; Setegn, Tesfaye; Biadgilign, Sibhatu

2014-12-01

Even though many studies showed that infant and child feeding index has a statistically significant association with nutritional status, there is paucity of studies on stability of infant and child feeding index over time and its association with nutritional status of HIV exposed infants. This study aimed to investigate the stability of infant and child feeding index over time that is developed based on the current recommendations and its association with nutritional status of HIV exposed infants in Sidama Zone, Southern Ethiopia. A panel study design was conducted in health institutions in Sidama Zone from February to July, 2012. Three repeated measurements of data were collected from each HIV exposed infant aged 6-17 months over the 6 month follow-up period approximately per 2 month interval. The cross-sectional index was found stable overtime with the repeatability coefficient of 0.802 which differed significantly from zero (95% CI: 0.75-0.85). A longitudinal infant and child feeding index (L-ICFI) has a statistically significant association with length for age Z scores (LAZ) and weight for age Z scores (WAZ) at visit three (β=0.262, p=0.007; β=0.226, p=0.017), respectively. But the longitudinal index has no statistically significant association with WLZ score (p=0.552). There was no significant difference in change of LAZ and WAZ over time between L-ICFI tertiles for both female and male HIV exposed infants. The index is stable overtime at individual level even though one third of the index components were not stable. The L-CFI was associated with LAZ and WAZ but not with WLZ. However there was no significant difference in change of HAZ and WAZ over time between L-ICFI tertiles for both female and male HIV exposed infants. Copyright © 2014 Elsevier Ltd. All rights reserved.

Analysis of stability and quench in HTS devices-New approaches

International Nuclear Information System (INIS)

Vysotsky, V.S.; Sytnikov, V.E.; Rakhmanov, A.L.; Ilyin, Y.

2006-01-01

R and D of HTS devices are in their full steam-more magnets and devices are developed with larger sizes. But analysis of their stability and quench was still old fashioned, based on normal zone determination, analysis of its appearance and propagation. Some peculiarities of HTS make this traditional, quite impractical and inconvenient approach to consideration of HTS devices stability and quench development using normal zone origination and propagation analysis. The novel approaches were developed that consider the HTS device as a cooled medium with non-linear parameters with no mentioning of 'superconductivity' in the analysis. The approach showed its effectiveness and convenience to analyze the stability and quench development in HTS devices. In this paper the analysis of difference between HTS and LTS quench, dependent on index n and specific heat comparison, is followed by the short approach descriptions and by the consequences from it for the HTS devices design. The further development of the method is presented for the analysis of long HTS objects where 'blow-up' regimes may happen. This is important for design and analysis of HTS power cables operations under overloading conditions

Dynamics, stability analysis and quantization of β-Fermi–Pasta ...

Indian Academy of Sciences (India)

We study the well-known one-dimensional problem of particles with nonlinear interaction. The -Fermi–Pasta–Ulam model is the special case of quadratic and quartic interaction potential among nearest neighbours. We enumerate and classify the simple periodic orbits for this system and find the stability zones, ...

Soil manganese redox cycling in suboxic zones: Effects on soil carbon stability

Science.gov (United States)

Suboxic soil environments contain a disproportionately higher concentration of highly reactive free radicals relative to the surrounding soil matrix, which may have significant implications for soil organic matter cycling and stabilization. This study investigated how Mn-ozidizin...

Stabilizing Cloud Feedback Dramatically Expands the Habitable Zone of Tidally Locked Planets

OpenAIRE

Yang, Jun; Cowan, Nicolas B.; Abbot, Dorian S.

2013-01-01

The habitable zone (HZ) is the circumstellar region where a planet can sustain surface liquid water. Searching for terrestrial planets in the HZ of nearby stars is the stated goal of ongoing and planned extrasolar planet surveys. Previous estimates of the inner edge of the HZ were based on one-dimensional radiative-convective models. The most serious limitation of these models is the inability to predict cloud behavior. Here we use global climate models with sophisticated cloud schemes to sho...

Zone separator for multiple zone vessels

Science.gov (United States)

Jones, John B.

1983-02-01

A solids-gas contact vessel, having two vertically disposed distinct reaction zones, includes a dynamic seal passing solids from an upper to a lower zone and maintaining a gas seal against the transfer of the separate treating gases from one zone to the other, and including a stream of sealing fluid at the seal.

Colloid-Facilitated Transport of Radionuclides through the Vadose Zone

International Nuclear Information System (INIS)

Flury, Markus; Harsh, James B.; Zachara, John M.; McCarthy, John F.; Lichtner, Peter C.

2006-01-01

This project seeks to improve the basic understanding of the role of colloids in facilitating the transport of contaminants in the vadose zone. We focus on three major thrusts: (1) thermodynamic stability and mobility of colloids formed by reactions of sediments with highly alkaline tank waste solutions, (2) colloid-contaminant interactions, and (3) in-situ colloid mobilization and colloid facilitated contaminant transport occurring in both contaminated and uncontaminated Hanford sediments

Water-induced convection in the Earth's mantle transition zone

Science.gov (United States)

Richard, Guillaume C.; Bercovici, David

2009-01-01

Water enters the Earth's mantle by subduction of oceanic lithosphere. Most of this water immediately returns to the atmosphere through arc volcanism, but a part of it is expected as deep as the mantle transition zone (410-660 km depth). There, slabs can be deflected and linger before sinking into the lower mantle. Because it lowers the density and viscosity of the transition zone minerals (i.e., wadsleyite and ringwoodite), water is likely to affect the dynamics of the transition zone mantle overlying stagnant slabs. The consequences of water exchange between a floating slab and the transition zone are investigated. In particular, we focus on the possible onset of small-scale convection despite the adverse thermal gradient (i.e., mantle is cooled from below by the slab). The competition between thermal and hydrous effects on the density and thus on the convective stability of the top layer of the slab is examined numerically, including water-dependent density and viscosity and temperature-dependent water solubility. For plausible initial water content in a slab (≥0.5 wt %), an episode of convection is likely to occur after a relatively short time delay (5-20 Ma) after the slab enters the transition zone. However, water induced rheological weakening is seen to be a controlling parameter for the onset time of convection. Moreover, small-scale convection above a stagnant slab greatly enhances the rate of slab dehydration. Small-scale convection also facilitates heating of the slab, which in itself may prolong the residence time of the slab in the transition zone.

Parapapillary atrophy: histological gamma zone and delta zone.

Directory of Open Access Journals (Sweden)

Jost B Jonas

Full Text Available BACKGROUND: To examine histomorphometrically the parapapillary region in human eyes. METHODOLOGY/PRINCIPAL FINDINGS: The histomorphometric study included 65 human globes (axial length:21-37 mm. On anterior-posterior histological sections, we measured the distance Bruch's membrane end (BME-optic nerve margin ("Gamma zone", BME-retinal pigment epithelium (RPE ("Beta zone", BME-beginning of non-occluded choriocapillaris, and BME-beginning of photoreceptor layer. "Delta zone" was defined as part of gamma zone in which blood vessels of at least 50 µm diameter were not present over a length of >300 µm. Beta zone (mean length:0.35±0.52 mm was significantly (P = 0.01 larger in the glaucoma group than in the non-glaucomatous group. It was not significantly (P = 0.28 associated with axial length. Beta zone was significantly (P = 0.004 larger than the region with occluded choriocapillaris. Gamma zone (mean length:0.63±1.25 mm was associated with axial length (P50 µm diameter within gamma zone was present only in highly axially elongated globes and was not related with glaucoma. Beta zone (Bruch's membrane without RPE was correlated with glaucoma but not with globe elongation. Since the region with occluded choriocapillaris was smaller than beta zone, complete loss of RPE may have occurred before complete choriocapillaris closure.

[Research on Cultivation and Stability of Nitritation Granular Sludge in Integrated ABR-CSTR Reactor].

Science.gov (United States)

Wu, Kai-cheng; Wu, Peng; Shen, Yao-liang; Li, Yue-han; Wang, Han-fang; Xu, Yue-zhong

2015-11-01

Abstract: The last two compartments of the Anaerobic Baffled Readtor ( ABR) were altered into aeration tank and sedimentation tank respectively to get an integrated anaerobic-aerobic reactor, using anaerobic granular sludge in anaerobic zone and aerobic granular sludge in aerobic zone as seed sludge. The research explored the condition to cultivate nitritation granular sludge, under the condition of continuous flow. The C/N rate was decreased from 1 to 0.4 and the ammonia nitrogen volumetric loading rate was increased from 0.89 kg x ( m3 x d)(-1) to 2.23 kg x (m3 x d)(-1) while the setting time of 1 h was controlled in the aerobic zone. After the system was operated for 45 days, the mature nitritation granular sludge in aerobic zone showed a compact structure and yellow color while the nitrite accumulation rate was about 80% in the effluent. The associated inhibition of free ammonia (FA) and free nitrous acid (FNA) dominated the nitritation. Part of granules lost stability during the initial period of operation and flocs appeared in the aerobic zone. However, the flocs were transformed into newly generated small particles in the following reactor operation, demonstrating that organic carbon was benefit to granulation and the enrichment of slow-growing nitrifying played an important role in the stability of granules.

Impact of the Sea Empress oil spill on lysosomal stability in mussel blood cells.

Science.gov (United States)

Fernley, P W; Moore, M N; Lowe, D M; Donkin, P; Evans, S

2000-01-01

Coastal zones are among the most productive and vulnerable areas on the planet. An example of impact on these fragile environments was shown in the case of the "Sea Empress" oil tanker, which ran aground in the Bristol Channel in 1996, spilling 72,000 tons of "Forties" crude oil. The objective was to investigate the sub-lethal cellular pathology and tissue hydrocarbon contamination in marine mussel populations, 4 months after the initial spill, using the neutral red retention (NRR) assay for lysosomal stability in blood cells. NRR was reduced in mussels, and indicative of cell injury, from the two sites closest to the spill in comparison with more distant and reference sites. Lysosomal stability was inversely correlated with polycyclic aromatic hydrocarbon concentrations in mussel tissues. Reduced lysosomal stability has previously been shown to contribute to impaired immunocompetence and to autophagic loss of body tissues. The use of this type of technique is discussed in the context of cost-effective, ecotoxicological tools for Integrated Coastal Zone Management.

Impact of the Sea Empress oil spill on lysosomal stability in mussel blood cells

International Nuclear Information System (INIS)

Fernley, P.W.; Lowe, D.M.; Donkin, P.; Evans, S.

2000-01-01

Coastal zones are among the most productive and vulnerable areas on the planet. An example of impact on these fragile environments was shown in the case of the Sea Empress oil tanker, which ran aground in the Bristol Channel in 1996, spilling 72,000 tonnes of Forties crude oil. The objective was to investigate the sub-lethal cellular pathology and tissue hydrocarbon contamination in marine mussel populations, 4 months after the initial spill, using the neutral red retention (NRR) assay for lysosomal stability in blood cells. NRR was reduced in mussels, and indicative of cell injury, from the two sites closest to the spill in comparison with more distant and reference sites. Lysosomal stability was inversely correlated with polycyclic aromatic hydrocarbon concentrations in mussel tissues. Reduced lysosomal stability has previously been shown to contribute to impaired immunocompetence and to autophagic loss of body tissues. The use of this type of technique is discussed in the context of cost-effective, ecotoxicological tools for Integrated Coastal Zone Management. (Author)

Impact of the Sea Empress oil spill on lysosomal stability in mussel blood cells

Energy Technology Data Exchange (ETDEWEB)

Fernley, P.W.; Lowe, D.M.; Donkin, P.; Evans, S. [Plymouth Marine Lab. (United Kingdom). Centre for Coastal and Marine Sciences; Moore, M.N. [Plymouth Marine Lab. (United Kingdom). Centre for Coastal and Marine Sciences; UNIDO, SES/PEM, Vienna International Centre (Austria)

2000-07-01

Coastal zones are among the most productive and vulnerable areas on the planet. An example of impact on these fragile environments was shown in the case of the Sea Empress oil tanker, which ran aground in the Bristol Channel in 1996, spilling 72,000 tonnes of Forties crude oil. The objective was to investigate the sub-lethal cellular pathology and tissue hydrocarbon contamination in marine mussel populations, 4 months after the initial spill, using the neutral red retention (NRR) assay for lysosomal stability in blood cells. NRR was reduced in mussels, and indicative of cell injury, from the two sites closest to the spill in comparison with more distant and reference sites. Lysosomal stability was inversely correlated with polycyclic aromatic hydrocarbon concentrations in mussel tissues. Reduced lysosomal stability has previously been shown to contribute to impaired immunocompetence and to autophagic loss of body tissues. The use of this type of technique is discussed in the context of cost-effective, ecotoxicological tools for Integrated Coastal Zone Management. (Author)

Atom-Probe Tomographic Investigation of Austenite Stability and Carbide Precipitation in a TRIP-Assisted 10 Wt Pct Ni Steel and Its Weld Heat-Affected Zones

Science.gov (United States)

Jain, Divya; Seidman, David N.; Barrick, Erin J.; DuPont, John N.

2018-04-01

Newly developed low-carbon 10 wt pct Ni-Mo-Cr-V martensitic steels rely on the Ni-enriched, thermally stable austenite [formed via multistep intercritical Quench-Lamellarization-Tempering ( QLT)-treatment] for their superior mechanical properties, specifically ballistic resistance. Critical to the thermal stability of austenite is its composition, which can be severely affected in the weld heat-affected zones (HAZs) and thus needs investigations. This article represents the first study of the nanoscale redistributions of C, Ni, and Mn in single-pass HAZ microstructures of QLT-treated 10 wt pct Ni steels. Local compositions of Ni-rich regions (representative of austenite compositions) in the HAZs are determined using site-specific 3-D atom-probe tomography (APT). Martensite-start temperatures are then calculated for these compositions, employing the Ghosh-Olson thermodynamic and kinetics approach. These calculations predict that austenite (present at high temperatures) in the HAZs is susceptible to a martensitic transformation upon cooling to room temperature, unlike the austenite in the QLT-treated base-metal. While C in the QLT-treated base-metal is consumed primarily in MC and M2C-type carbide precipitates (M is Mo, Cr, V), its higher concentration in the Ni-rich regions in the HAZs indicates the dissolution of carbide precipitates, particularly M2C carbide precipitates. The role of M2C carbide precipitates and austenite stability is discussed in relation to the increase in microhardness values observed in the HAZs, relative to the QLT-treated base-metal. Insights gained from this research on austenite stability and carbide precipitation in the single-pass HAZ microstructures will assist in designing multiple weld cycles for these novel 10 wt pct Ni steels.

The constructive process in the Cimorro zone in the the Cathedral of Avila, (century XII-XIV. Hypothesis and its verification through the analysis of Structural Stability Smart and Sustainable Offices (SSO

Directory of Open Access Journals (Sweden)

Mª A. Benito Pradillo

2018-01-01

Full Text Available This paper presents a hypothesis about the order in the constructive process for the head zone in the Cathedral of Ávila, called Cimorro. The hypothesis proposed in this area considers for its construction three different stages: XII Century, XIII Century and XIV Century. The proposed hypotesis have been verified with the Analysis of Stability realised. The theoretical Framework used is the Limit Analysis to Masonry Structures. After prooving the Structural Stability for each of the building stages, the following conclusions are made: Through the XII Century, the possibility of closing the central vault without Buttress System for a short period of time and the subsequent placement of a tribune is stated. A fortification formed by the barbican and the «adarves» were built during the XIII Century. In the XIV Century, the tribune is removed and replaced with the Buttress System with buttress and double flying buttress, which we can see nowadays.

A new stabilized least-squares imaging condition

International Nuclear Information System (INIS)

Vivas, Flor A; Pestana, Reynam C; Ursin, Bjørn

2009-01-01

The classical deconvolution imaging condition consists of dividing the upgoing wave field by the downgoing wave field and summing over all frequencies and sources. The least-squares imaging condition consists of summing the cross-correlation of the upgoing and downgoing wave fields over all frequencies and sources, and dividing the result by the total energy of the downgoing wave field. This procedure is more stable than using the classical imaging condition, but it still requires stabilization in zones where the energy of the downgoing wave field is small. To stabilize the least-squares imaging condition, the energy of the downgoing wave field is replaced by its average value computed in a horizontal plane in poorly illuminated regions. Applications to the Marmousi and Sigsbee2A data sets show that the stabilized least-squares imaging condition produces better images than the least-squares and cross-correlation imaging conditions

Saline flushing fluids restricting contamination of the near-face zone

Energy Technology Data Exchange (ETDEWEB)

Weil, W

1982-01-01

Questions are covered which concern the characteristics and main properties of saline solutions without solid phase and their use as flushing fluids. Attention is drawn to the fact that these solutions are universally used in flushing and other operations of wells with high gradients of bed pressures, and also in those cases where the oil and gas levels are especially sensitive to negative influence of traditional clay solutions which cause irreversible decrease in permeability of the reservoirs through contamination and plugging of the pores in the near-face zone, and consequently, influence the decrease in bed productivity. The described methods and chemical reagents decrease the filtering of these solutions in the reservoirs, improve viscosity and stabilize the near-face zone.

Approaching hydrate and free gas distribution at the SUGAR-Site location in the Danube Delta

Science.gov (United States)

Bialas, Joerg; Dannowski, Anke; Zander, Timo; Klaeschen, Dirk; Klaucke, Ingo

2017-04-01

Gas hydrates did receive a lot of attention over the last decades when investigating their potential to serve as a possible source for Methane production. Among other world-wide programs the German SUGAR project sets out to investigate the entire chain from exploitation to production in Europe. Therefore research in the scope of the SUGAR project sets out to investigate a site in European EEZ for the detailed studies of hydrate and gas distribution in a permeable sediment matrix. Among others one aim of the project is to provide in situ samples of natural methane hydrate for further investigations by MEBO drilling. The Danube paleo-delta with its ancient canyon and levee systems was chosen as a possible candidate for hydrate formation within the available drilling range of 200 m below seafloor. In order to decide on the best drilling location cruise MSM34 (Bialas et al., 2014) of the German RV MARIA S MERIAN set out to acquire geophysical, geological and geochemical datasets for assessment of the hydrate content within the Danube paleo-delta, Black Sea. The Black Sea is well known for a significant gas content in the sedimentary column. Reports on observations of bottom simulating reflectors (BSR) by Popescu et al. (2007) and others indicate that free gas and hydrate occurrence can be expected within the ancient passive channel levee systems. A variety of inverted reflection events within the gas hydrate stability zone (GHSZ) were observed within the drilling range of MEBO and chosen for further investigation. Here we report on combined seismic investigations of high-resolution 2D & 3D multichannel seismic (MCS) acquisition accompanied by four component Ocean-Bottom-Seismometer (OBS) observations. P- and converted S-wave arrivals within the OBS datasets were analysed to provide overall velocity depth models. Due to the limited length of profiles the majority of OBS events are caused by near vertical reflections. While P-wave events have a significant lateral

Stable Heliconius butterfly hybrid zones are correlated with a local rainfall peak at the edge of the Amazon basin.

Science.gov (United States)

Rosser, Neil; Dasmahapatra, Kanchon K; Mallet, James

2014-12-01

Multilocus clines between Müllerian mimetic races of Heliconius butterflies provide a classic example of the maintenance of hybrid zones and their importance in speciation. Concordant hybrid zones in the mimics Heliconius erato and H. melpomene in northern Peru were carefully documented in the 1980s, and this prior work now permits a historical analysis of the movement or stasis of the zones. Previous work predicted that these zones might be moving toward the Andes due to selective asymmetry. Extensive deforestation and climate change might also be expected to affect the positions and widths of the hybrid zones. We show that the positions and shapes of these hybrid zones have instead remained remarkably stable between 1985 and 2012. The stability of this interaction strongly implicates continued selection, rather than neutral mixing following secondary contact. The stability of cline widths and strong linkage disequilibria (gametic correlation coefficients Rmax = 0.35-0.56 among unlinked loci) over 25 years suggest that mimetic selection pressures on each color pattern locus have remained approximately constant (s ≈ 0.13-0.40 per locus in both species). Exceptionally high levels of precipitation at the edge of the easternmost Andes may act as a population density trough for butterflies, trapping the hybrid zones at the foot of the mountains, and preventing movement. As such, our results falsify one prediction of the Pleistocene Refugium theory: That the ranges of divergent species or subspecies should be centered on regions characterized by maxima of rainfall, with hybrid zones falling in more arid regions between them. © 2014 The Author(s). Evolution © 2014 The Society for the Study of Evolution.

Dependence of stability of metastable superconductors on copper fraction

International Nuclear Information System (INIS)

Elrod, S.A.; Lue, J.W.; Miller, J.R.; Dresner, L.

1980-12-01

The stability of composite superconductors operating in the metastable regime depends upon such factors as matrix resistivity, cooled surface dimensions, fraction of critical current, and volume fraction of stabilizer. By assuming constant thermophysical properties, we developed analytic expressions for the energy and voltage of the minimum propagating zone (MPZ). With other factors held constant, these expressions have been used to predict composite superconductor stability as a function of copper fraction: lower copper fractions lead to higher MPZ energies. MPZ voltages have been measured for three NbTi/Cu composites having different copper fractions and different critical current densities for several magnetic fields and transport currents. Experimental MPZ voltages have been used to calculate an effective heat transfer coefficient, which is subsequently used to calculate the MPZ energy. The experimental MPZ energies support the theoretical expectation that lower copper fractions lead to higher stability in the metastable regime

Application of contact stabilization activated sludge for enhancing biological phosphorus removal (EBPR in domestic wastewater

Directory of Open Access Journals (Sweden)

Ehab M. Rashed

2014-04-01

Full Text Available The experiment has been performed in order to investigate the effect of using contact stabilization activated sludge as an application of enhancing biological phosphorous removal (EBPR by using contact tank as a phosphorus uptake zone and using thickening tank as a phosphorus release zone. The study involved the construction of a pilot plant which was setup in Quhafa waste water treatment plant (WWTP that included contact, final sedimentation, stabilization and thickening tanks, respectively with two returns sludge in this system one of them to contact tank and another to stabilization tank. Then observation of the uptake and release of total phosphorus by achievement through two batch test using sludge samples from thickener and final sedimentations. Results showed the removal efficiencies of COD, BOD and TP for this pilot plant with the range of 94%, 85.44% and 80.54%, respectively. On the other hand the results of batch tests showed that the reason of high ability of phosphorus removal for this pilot plant related to the high performance of microorganisms for phosphorus accumulating. Finally the mechanism of this pilot plant depends on the removal of the phosphorus from the domestic waste water as a concentrated TP solution from the supernatant above the thickening zone not through waste sludge like traditional systems.

Ecosystem health evaluation system of the water-fluctuating zone in the Three Gorges Area

Institute of Scientific and Technical Information of China (English)

WANG Li-ao; YUAN Hui; ZHANG Yan-hui; HU Gang

2004-01-01

This paper discribes the definition of ecosystem health for the water-level flutuation zone of the Three Gorges Region and puts forward an evaluation system involving indicators in three groups: 1) structural indicators comprise slope, biodiversity,environmental capacity, stability, restoration ability and damage situation; 2) functional indicators including probability of geological hazard, erosion rate, habitat rate, land use intension and days of tourist season; 3) environmental indicatiors made up of population quality, potential intension of human, ground water quality, ambient air quality, wastewater treatment rate, pesticide use rate, fertilizer use rate, environmental management and public participation. In the design of the system, the subject zone is regarded as the type similar to wetland and the impacts of human activities on the zone are attached great importance to.

Infinite slope stability under steady unsaturated seepage conditions

Science.gov (United States)

Lu, Ning; Godt, Jonathan W.

2008-01-01

We present a generalized framework for the stability of infinite slopes under steady unsaturated seepage conditions. The analytical framework allows the water table to be located at any depth below the ground surface and variation of soil suction and moisture content above the water table under steady infiltration conditions. The framework also explicitly considers the effect of weathering and porosity increase near the ground surface on changes in the friction angle of the soil. The factor of safety is conceptualized as a function of the depth within the vadose zone and can be reduced to the classical analytical solution for subaerial infinite slopes in the saturated zone. Slope stability analyses with hypothetical sandy and silty soils are conducted to illustrate the effectiveness of the framework. These analyses indicate that for hillslopes of both sandy and silty soils, failure can occur above the water table under steady infiltration conditions, which is consistent with some field observations that cannot be predicted by the classical infinite slope theory. A case study of shallow slope failures of sandy colluvium on steep coastal hillslopes near Seattle, Washington, is presented to examine the predictive utility of the proposed framework.

Interaction between drilled shaft and mechanically stabilized earth (MSE) wall : project summary.

Science.gov (United States)

2015-08-31

Drilled shafts are being constructed within the reinforced zone of mechanically stabilized earth (MSE) walls (Figure 1). The drilled shafts may be subjected to horizontal loads and push against the front of the wall. Distress of MSE wall panels has b...

Lean premixed reacting flows with swirl and wall-separation zones in a contracting chamber

Science.gov (United States)

Zhang, Yuxin; Rusak, Zvi; Wang, Shixiao

2017-11-01

Low Mach number lean premixed reacting swirling flows with wall-separation zones in a contracting circular finite-length open chamber are studied. Assuming a complete reaction with high activation energy and chemical equilibrium behind the reaction zone, a nonlinear partial differential equation is derived for the solution of the flow stream function behind the reaction zone in terms of the inlet total enthalpy for a reacting flow, specific entropy and the circulation functions. Bifurcation diagrams of steady flows are described as the inlet swirl level is increased at fixed chamber contraction and reaction heat release. The approach is applied to an inlet solid-body rotation flow with constant profiles of the axial velocity, temperature and mixture reactant mass fraction. The computed results provide predictions of the critical inlet swirl levels for the first appearance of wall-separation states and for the size of the separation zone as a function of the inlet swirl ratio, Mach number, chamber contraction and heat release of the reaction. The methodology developed in this paper provides a theoretical feasibility for the development of the technology of swirl-assisted combustion where the reaction zone is supported and stabilized by a wall-separation zone.

Evaluation of primary and secondary stability of titanium implants using different surgical techniques.

Science.gov (United States)

Tabassum, Afsheen; Meijer, Gert J; Walboomers, X Frank; Jansen, John A

2014-04-01

To investigate the influence of different surgical techniques on the primary and secondary implant stability using trabecular bone of goats as an implantation model. In the iliac crest of eight goats, 48 cylindrical-screw-type implants with a diameter of 4.2 mm (Dyna(®) ; Bergen op Zoom, the Netherlands) were installed, using three different surgical techniques: (i) 5% undersized, using a final drill diameter of 4 mm; (ii) 15% undersized, using a final drill diameter of 3.6 mm; and (iii) 25% undersized, using a final drill diameter of 3.2 mm. Peak insertion torque values were measured by a Digital(®) (MARK-10 Corporation, New York, NY, USA) torque gauge instrument during placement. At 3 weeks after implantation, removal torque was measured. Histomorphometrically, the peri-implant bone volume was measured in three zones; the inner zone (0-500 μm), the middle zone (500-1000 μm) and the outer zone (1000-1500 μm). Evaluation of the obtained data demonstrated no statistically significant difference between different surgical techniques regarding removal torque values. With respect to the percentage peri-implant bone volume (%BV), also no significant difference could be observed between all three applied surgical techniques for both the inner, middle and outer zone. However, irrespective of the surgical technique, it was noticed that the %BV was significantly higher for the inner zone as compared to middle and outer zone (P < 0.05) around the implant. At 3 weeks after implant installation, independent of the used undersized surgical technique, the %BV in the inner zone (0-500 μm) peri-implant area was improved due to both condensation of the surrounding bone as also the translocation of host bone particles along the implant surface. Surprisingly, no mechanical beneficial effect of the 25% undersized surgical technique could be observed as compared to the 5% or 15% undersized surgical technique to improve primary or secondary implant stability. © 2013

Accessory minerals and subduction zone metasomatism: a geochemical comparison of two mélanges (Washington and California, U.S.A.)

Science.gov (United States)

Sorensen, Sorena S.; Grossman, Jeffrey N.

1993-01-01

The ability of a subducted slab or subducted sediment to contribute many incompatible trace elements to arc source regions may depend on the stabilities of accessory minerals within these rocks, which can only be studied indirectly. In contrast, the role of accessory minerals in lower-T and -P metasomatic processes within paleo-subduction zones can be studied directly in subduction-zone metamorphic terranes.

Analytical Prediction of Three Dimensional Chatter Stability in Milling

Science.gov (United States)

Altintas, Yusuf

The chip regeneration mechanism during chatter is influenced by vibrations in three directions when milling cutters with ball end, bull nose, or inclined cutting edges are used. A three dimensional chatter stability is modeled analytically in this article. The dynamic milling system is formulated as a function of cutter geometry, the frequency response of the machine tool structure at the cutting zone in three Cartesian directions, cutter engagement conditions and material property. The dynamic milling system with nonlinearities and periodic delayed differential equations is reduced to a three dimensional linear stability problem by approximations based on the physics of milling. The chatter stability lobes are predicted in the frequency domain using the proposed analytical solution, and verified experimentally in milling a Titanium alloy with a face milling cutter having circular inserts.

The study of stress-strain state of stabilized layered soil foundations

Directory of Open Access Journals (Sweden)

Sokolov Mikhail V.

2017-01-01

Full Text Available Herein presented are the results of modeling and analysis of stress-strain state of layered inhomogeneous foundation soil when it is stabilised by injection to different depths. Produced qualitative and quantitative analysis of the components of the field of isolines of stresses, strains, stress concentration and the difference between the strain at the boundary of different elastic horizontal layers. Recommendations are given for the location of stabilised zones in relation to the border of different elastic layers. In particular, it found that stabilization of soil within the weak layer is inappropriate, since it practically provides no increase in the stability of the soil foundation, and when performing stabilisation of soil foundations, it is recommended to place the lower border of the stabilisation zone below the border of a stronger layer, at this the distribution of stresses and strains occurs more evenly, and load-bearing capacity of this layer is used to the maximum.

Optimal control of diarrhea transmission in a flood evacuation zone

Science.gov (United States)

Erwina, N.; Aldila, D.; Soewono, E.

2014-03-01

Evacuation of residents and diarrhea disease outbreak in evacuation zone have become serious problem that frequently happened during flood periods. Limited clean water supply and infrastructure in evacuation zone contribute to a critical spread of diarrhea. Transmission of diarrhea disease can be reduced by controlling clean water supply and treating diarrhea patients properly. These treatments require significant amount of budget, which may not be fulfilled in the fields. In his paper, transmission of diarrhea disease in evacuation zone using SIRS model is presented as control optimum problem with clean water supply and rate of treated patients as input controls. Existence and stability of equilibrium points and sensitivity analysis are investigated analytically for constant input controls. Optimum clean water supply and rate of treatment are found using optimum control technique. Optimal results for transmission of diarrhea and the corresponding controls during the period of observation are simulated numerically. The optimum result shows that transmission of diarrhea disease can be controlled with proper combination of water supply and rate of treatment within allowable budget.

Stability of black hole accretion disks

Directory of Open Access Journals (Sweden)

Czerny B.

2012-12-01

Full Text Available We discuss the issues of stability of accretion disks that may undergo the limit-cycle oscillations due to the two main types of thermal-viscous instabilities. These are induced either by the domination of radiation pressure in the innermost regions close to the central black hole, or by the partial ionization of hydrogen in the zone of appropriate temperatures. These physical processes may lead to the intermittent activity in AGN on timescales between hundreds and millions of years. We list a number of observational facts that support the idea of the cyclic activity in high accretion rate sources. We conclude however that the observed features of quasars may provide only indirect signatures of the underlying instabilities. Also, the support from the sources with stellar mass black holes, whose variability timescales are observationally feasible, is limited to a few cases of the microquasars. Therefore we consider a number of plausible mechanisms of stabilization of the limit cycle oscillations in high accretion rate accretion disks. The newly found is the stabilizing effect of the stochastic viscosity fluctuations.

Highly stabilized partially premixed flames of propane in a concentric flow conical nozzle burner with coflow

KAUST Repository

Elbaz, Ayman M.

2018-01-11

Partially premixed turbulent flames with non-homogeneous jet of propane were generated in a concentric flow conical nozzle burner in order to investigate the effect of the coflow on the stability and flame structure. The flame stability is first mapped and then high-speed stereoscopic particle image velocimetry, SPIV, plus OH planar laser-induced fluorescence, OH-PLIF, measurements were conducted on a subset of four flames. The jet equivalence ratio Φ = 2, Jet exit Reynolds number Re = 10,000, and degree of premixing are kept constant for the selected flames, while the coflow velocity, Uc, is progressively changed from 0 to 15 m/s. The results showed that the flame is stable between two extinction limits of mixture inhomogeneity, and the optimum stability is obtained at certain degree of mixture inhomogeneity. Increasing Φ, increases the span between these two extinction limits, while these limits converge to a single point (corresponding to optimum mixture inhomogeneity) with increasing Re. Regardless the value of Φ, increasing the coflow velocity improves the flame stability. The correlation between recessed distance of the burner tubes and the fluctuation of the mixture fraction, Δξ, shows that at Δξ around 40% of the flammability limits leads to optimum flame stability. The time averaged SPIV results show that the coflow induces a big annular recirculation zone surrounds the jet flames. The size and the location of this zone is seen to be sensitive to Uc. However, the instantaneous images show the existence of a small vortical structure close to the shear layer, where the flame resides there in the case of no-coflow. These small vertical structures are seen playing a vital role in the flame structure, and increasing the flame corrugation close to the nozzle exit. Increasing the coflow velocity expands the central jet at the expense of the jet velocity, and drags the flame in the early flame regions towards the recirculation zone, where the flame tracks

Monetary policy efficiency in the euro zone: some empirical evidence of money demand stability and endogeneity

Directory of Open Access Journals (Sweden)

Kapounek, S.

2010-12-01

Full Text Available The primary target of most central banks in developed economies is to maintain price stability. When there is no threat to the fulfilment of the primary target, the central bank focuses on its secondary target which is defined as support of a sustainable economic growth and full employment. Even though, a substantial part of the discussions regarding the targets of the central banks focus on price stability, the real target is to support a sustainable economic growth, especially to stabilize the fluctuation in the economic activity.This paper focuses on the current problems of monetary policy implementation in the Eurozone. Firstly, the author focus on the money demand function estimation and its stability. Another problem lies in the Postkeynesians´ assumptions of money endogeneity. Although central banks may have certain control over the money supply, they cannot fix the stock of money in a country. Different trends in monetary aggregates fluctuation contribute to reject the money exogeneity hypothesis.

Radiation protection zoning

International Nuclear Information System (INIS)

2015-01-01

Radiation being not visible, the zoning of an area containing radioactive sources is important in terms of safety. Concerning radiation protection, 2 work zones are defined by regulations: the monitored zone and the controlled zone. The ministerial order of 15 may 2006 settles the frontier between the 2 zones in terms of radiation dose rates, the rules for access and the safety standards in both zones. Radioprotection rules and the name of the person responsible for radiation protection must be displayed. The frontier between the 2 zones must be materialized and marked with adequate equipment (specific danger signs and tapes). Both zones are submitted to selective entrance, the access for the controlled zone is limited because of the radiation risk and of the necessity of confining radioactive contamination while the limitation of the access to the monitored zone is due to radiation risk only. (A.C.)

Riparian zone controls on base cation concentrations in boreal streams

Science.gov (United States)

Ledesma, J. L. J.; Grabs, T.; Futter, M. N.; Bishop, K. H.; Laudon, H.; Köhler, S. J.

2013-01-01

Forest riparian zones are a major in control of surface water quality. Base cation (BC) concentrations, fluxes, and cycling in the riparian zone merit attention because of increasing concern of negative consequences for re-acidification of surface waters from future climate and forest harvesting scenarios. We present a two-year study of BC and silica (Si) flow-weighted concentrations from 13 riparian zones and 14 streams in a boreal catchment in northern Sweden. The Riparian Flow-Concentration Integration Model (RIM) was used to estimate riparian zone flow-weighted concentrations and tested to predict the stream flow-weighted concentrations. Spatial variation in BC and Si concentrations as well as in flow-weighted concentrations was related to differences in Quaternary deposits, with the largest contribution from lower lying silty sediments and the lowest contribution from wetland areas higher up in the catchment. Temporal stability in the concentrations of most elements, a remarkably stable Mg / Ca ratio in the soil water and a homogeneous mineralogy suggest that the stable patterns found in the riparian zones are a result of distinct mineralogical upslope groundwater signals integrating the chemical signals of biological and chemical weathering. Stream water Mg / Ca ratio indicates that the signal is subsequently maintained in the streams. RIM gave good predictions of Ca, Mg, and Na flow-weighted concentrations in headwater streams. The difficulty in modelling K and Si suggests a stronger biogeochemical influence on these elements. The observed chemical dilution effect with flow in the streams was related to variation in groundwater levels and element concentration profiles in the riparian zones. This study provides a first step toward specific investigations of the vulnerability of riparian zones to changes induced by forest management or climate change, with focus on BC or other compounds.

Improving the treatment of non-aqueous phase TCE in low permeability zones with permanganate

International Nuclear Information System (INIS)

Chokejaroenrat, Chanat; Comfort, Steve; Sakulthaew, Chainarong; Dvorak, Bruce

2014-01-01

Graphical abstract: - Highlights: • Transport experiments used transmissive and low permeability zones (LPZs). • 14 C-labeled TCE was used to quantify oxidation of DNAPL in LPZs by permanganate. • Stabilization aids prevented MnO 2 rind formation. • DNAPL oxidation improved when xanthan and stabilization aids were used. - Abstract: Treating dense non-aqueous phase liquids (DNAPLs) embedded in low permeability zones (LPZs) is a particularly challenging issue for injection-based remedial treatments. Our objective was to improve the sweeping efficiency of permanganate (MnO 4 − ) into LPZs to treat high concentrations of TCE. This was accomplished by conducting transport experiments that quantified the penetration of various permanganate flooding solutions into a LPZ that was spiked with non-aqueous phase 14 C-TCE. The treatments we evaluated included permanganate paired with: (i) a shear-thinning polymer (xanthan); (ii) stabilization aids that minimized MnO 2 rind formation and (iii) a phase-transfer catalyst. In addition, we quantified the ability of these flooding solutions to improve TCE destruction under batch conditions by developing miniature LPZ cylinders that were spiked with 14 C-TCE. Transport experiments showed that MnO 4 − alone was inefficient in penetrating the LPZ and reacting with non-aqueous phase TCE, due to a distinct and large MnO 2 rind that inhibited the TCE from further oxidant contact. By including xanthan with MnO 4 − , the sweeping efficiency increased (90%) but rind formation was still evident. By including the stabilization aid, sodium hexametaphosphate (SHMP) with xanthan, permanganate penetrated 100% of the LPZ, no rind was observed, and the percentage of TCE oxidized increased. Batch experiments using LPZ cylinders allowed longer contact times between the flooding solutions and the DNAPL and results showed that SHMP + MnO 4 − improved TCE destruction by ∼16% over MnO 4 − alone (56.5% vs. 40.1%). These results support

A novel approach proposed for fractured zone detection using petrophysical logs

International Nuclear Information System (INIS)

Tokhmechi, B; Memarian, H; Noubari, H A; Moshiri, B

2009-01-01

Fracture detection is a key step in wellbore stability and fractured reservoir fluid flow simulation. While different methods have been proposed for fractured zones detection, each of them is associated with certain shortcomings that prevent their full use in different related engineering applications. In this paper, a novel combined method is proposed for fractured zone detection, using processing of petrophysical logs with wavelet, classification and data fusion techniques. Image and petrophysical logs from Asmari reservoir in eight wells of an oilfield in southwestern Iran were used to investigate the accuracy and applicability of the proposed method. Initially, an energy matching strategy was utilized to select the optimum mother wavelets for de-noising and decomposition of petrophysical logs. Parzen and Bayesian classifiers were applied to raw, de-noised and various frequency bands of logs after decomposition in order to detect fractured zones. Results show that the low-frequency bands (approximation 2, a 2 ) of de-noised logs are the best data for fractured zones detection. These classifiers considered one well as test well and the other seven wells as train wells. Majority voting, optimistic OWA (ordered weighted averaging) and pessimistic OWA methods were used to fuse the results obtained from seven train wells. Results confirmed that Parzen and optimistic OWA are the best combined methods to detect fractured zones. The generalization of method is confirmed with an average accuracy of about 72%

Arrangement for improving the strength of the bottom zones of gas wells

Energy Technology Data Exchange (ETDEWEB)

Tsaiger, M.A.; Ogneva, N.E.; Kogan, N.N.

1965-04-19

An arrangement for strengthening the incompetent zones of gas wells is based on phenol-formaldehyde resin and a catalyst (benzo-sulfo-acid). For increasing the stability of the formation without lowering its permeability, a preparation is injected into the formation which consists of 70-80% of resin and 20-30% of a water solution of benzo-sulfo-acid of 40-50% concentration.

Systematic study of formation of soft and hard zones in the dissimilar weldments of Cr-Mo steels

International Nuclear Information System (INIS)

Sudha, C.; Terrance, A.L.E.; Albert, S.K.; Vijayalakshmi, M.

2002-01-01

The microstructural stability and elemental redistribution in dissimilar weldments between 9Cr-1Mo and 2.25Cr-1Mo ferritic steels during various postweld heat treatments (PWHTs) have been studied using microscopy techniques ranging from optical to transmission electron microscopy and electron probe microanalyser. Application of PWHT at 1023 K for various times resulted in the formation of a soft zone in the low Cr side and a carbide rich hard zone adjoining the soft zone in the high Cr side of the weldment. The width of these zones and their hardness are influenced by the time of exposure at elevated temperature. A measurable increase in the width and a decrease in the hardness of the soft and hard zones with aging times are observed. Correlation between these observed effects and the elemental redistribution responsible for the formation of these zones is being attempted. Micromechanisms responsible for the formation of these zones are proposed. Migration of carbon from low Cr side to high Cr side driven by the gradient in the carbon activity has been found to be responsible for the formation of these zones

Evaluation of TBM tunnels with respect to stability against spalling

Science.gov (United States)

Shaalan, Heyam; Ismail, Mohd Ashraf Mohd; Azit, Romziah

2017-10-01

As the depth of tunnels and underground construction increases, instability occurs in the form of rock bursting or spalling because of the induced stresses. Spalling may appear as a strong compressive stress causing crack growth behind the excavated surface and buckling of the thin rock slabs. In this paper, we describe how to reduce the rock spalling failure to increase the underground safety and the tunnel stability. Thus, a parametric study is implemented using 2-D Elasto-plastic finite elements stress analysis software to investigate the parameters that can minimize the extent and depth of the failure zone. The critical section of Pahang Selangor Raw Water Transfer Tunnel under high overburden is analyzed. The effect of the shotcrete lining thickness, tunnel size and the removal of fallouts or scaled v-notch on the failure zone depth is investigated. The results demonstrate that the shotcrete lining thickness has less influence on the failure depth, while a small tunnel diameter minimizes the failure depth. In addition, the stability of the tunnel improves by removing the loose rock mass.

Definition of Management Zones for Enhancing Cultivated Land Conservation Using Combined Spatial Data

Science.gov (United States)

Li, Yan; Shi, Zhou; Wu, Hao-Xiang; Li, Feng; Li, Hong-Yi

2013-10-01

The loss of cultivated land has increasingly become an issue of regional and national concern in China. Definition of management zones is an important measure to protect limited cultivated land resource. In this study, combined spatial data were applied to define management zones in Fuyang city, China. The yield of cultivated land was first calculated and evaluated and the spatial distribution pattern mapped; the limiting factors affecting the yield were then explored; and their maps of the spatial variability were presented using geostatistics analysis. Data were jointly analyzed for management zone definition using a combination of principal component analysis with a fuzzy clustering method, two cluster validity functions were used to determine the optimal number of cluster. Finally one-way variance analysis was performed on 3,620 soil sampling points to assess how well the defined management zones reflected the soil properties and productivity level. It was shown that there existed great potential for increasing grain production, and the amount of cultivated land played a key role in maintaining security in grain production. Organic matter, total nitrogen, available phosphorus, elevation, thickness of the plow layer, and probability of irrigation guarantee were the main limiting factors affecting the yield. The optimal number of management zones was three, and there existed significantly statistical differences between the crop yield and field parameters in each defined management zone. Management zone I presented the highest potential crop yield, fertility level, and best agricultural production condition, whereas management zone III lowest. The study showed that the procedures used may be effective in automatically defining management zones; by the development of different management zones, different strategies of cultivated land management and practice in each zone could be determined, which is of great importance to enhance cultivated land conservation

Longitudinal propagation of the normal zone through indirectly cooled superconducting solenoids. V.2

International Nuclear Information System (INIS)

Devred, A.

1988-03-01

This work deals with the longitudinal propagation of the normal zone in large thin super-conducting solenoids like CELLO. From the theoretical point of view, we begin to explain, under the name of classical model, a synthesis of the models known in the literature. Then we study successively the influence of four phenomenons, which until then were neglected: 1) The current sharing zone; 2) The dependence on temperature of the specific heat and of the thermal conductivity; 3) The electromagnetic diffusion through a possible super-stabilizer, and 4) The thermal diffusion through a possible insulator. In each case, we re-formulate the equation of thermal and electromagnetic behaviour of the layer, we solve them analytically, and we derive a corrective factor, which is to apply to the classical formula of the propagation velocity. Finally, we investigate how to combine these corrections, and we converge on a general method of calculation of the velocity. In the experimental part, we have pointed out and measured in terms of current and field, propagation velocities along a super-stabilized conductor. Having established that the experimental conditions satisfied the hypotheses of our theoretical study, we verify that these measurements are in good agreement with the calculated velocities. Finally we concluded that our model of current redistribution through the super-stabilizer is valid [fr

Longitudinal propagation of the normal zone through indirectly cooled superconducting solenoidss. V.1

International Nuclear Information System (INIS)

Devred, A.

1988-03-01

This work deals with the longitudinal propagation of the normal zone in large thin super-conducting solenoids like CELLO. From the theoretical point of view, we begin to explain, under the name of classical model, a synthesis of the models known in the literature. Then we study successively the influence of four phenomenons, which until then were neglected: 1) The current sharing zone; 2) The dependence on temperature of the specific heat and of the thermal conductivity; 3) The electromagnetic diffusion through a possible super-stabilizer, and 4) The thermal diffusion through a possible insulator. In each case, we re-formulate the equation of thermal and electromagnetic behaviour of the layer, we solve them analytically, and we derive a corrective factor, which is to apply to the classical formula of the propagation velocity. Finally, we investigate how to combine these corrections, and we converge on a general method of calculation of the velocity. In the experimental part, we have pointed out and measured in terms of current and field, propagation velocities along a super-stabilized conductor. Having established that the experimental conditions satisfied the hypotheses of our theoretical study, we verify that these measurements are in good agreement with the calculated velocities. Finally we concluded that our model of current redistribution through the super-stabilizer is valid [fr

Cohesive zone modeling of intergranular cracking in polycrystalline aggregates

International Nuclear Information System (INIS)

Simonovski, Igor; Cizelj, Leon

2015-01-01

Highlights: • Alternative approach to cohesive elements is proposed: cohesive-zone contact. • Applicability to measured and simulated grain structures is demonstrated. • Normal and normal/shear separation as a damage initialization is explored. • Normal/shear damage initialization significantly reduces ductility. • Little difference in Voronoi aggregate size on macroscopic response. - Abstract: Understanding and controlling early damage initiation and evolution are amongst the most important challenges in nuclear power plants, occurring in ferritic, austenitic steels and nickel based alloys. In this work a meso-scale approach to modeling initiation and evolution of early intergranular cracking is presented. This damage mechanism is present in a number of nuclear power plant components and depends on the material (e.g. composition, heat treatment, microstructure), environment and load. Finite element modeling is used to explicitly model the microstructure – both the grains and the grain boundaries. Spatial Voronoi tessellation is used to obtain the grain topology. In addition, measured topology of a 0.4 mm stainless steel wire is used. Anisotropic elasticity and crystal plasticity are used as constitutive laws for the grains. Grain boundaries are modeled using the cohesive zone approach. Different modeling assumptions/parameters are evaluated against the numerical stability criteria. The biggest positive contribution to numerical stability is the use of cohesive-type contact instead of cohesive elements. A small amount of viscous regularization should be also used along with the addition of a small amount of viscous forces to the global equilibrium equations. Two cases of grain boundary damage initiation are explored: (1) initiation due to normal separation and (2) initiation due to a combination of normal and shear separation. The second criterion significantly decreases the ductility of an aggregate and slightly improves the numerical stability

Characterizing Excavation Damaged Zone and Stability of Pressurized Lined Rock Caverns for Underground Compressed Air Energy Storage

Science.gov (United States)

Kim, Hyung-Mok; Rutqvist, Jonny; Jeong, Ju-Hwan; Choi, Byung-Hee; Ryu, Dong-Woo; Song, Won-Kyong

2013-09-01

In this paper, we investigate the influence of the excavation damaged zone (EDZ) on the geomechanical performance of compressed air energy storage (CAES) in lined rock caverns. We conducted a detailed characterization of the EDZ in rock caverns that have been excavated for a Korean pilot test program on CAES in (concrete) lined rock caverns at shallow depth. The EDZ was characterized by measurements of P- and S-wave velocities and permeability across the EDZ and into undisturbed host rock. Moreover, we constructed an in situ concrete lining model and conducted permeability measurements in boreholes penetrating the concrete, through the EDZ and into the undisturbed host rock. Using the site-specific conditions and the results of the EDZ characterization, we carried out a model simulation to investigate the influence of the EDZ on the CAES performance, in particular related to geomechanical responses and stability. We used a modeling approach including coupled thermodynamic multiphase flow and geomechanics, which was proven to be useful in previous generic CAES studies. Our modeling results showed that the potential for inducing tensile fractures and air leakage through the concrete lining could be substantially reduced if the EDZ around the cavern could be minimized. Moreover, the results showed that the most favorable design for reducing the potential for tensile failure in the lining would be a relatively compliant concrete lining with a tight inner seal, and a relatively stiff (uncompliant) host rock with a minimized EDZ. Because EDZ compliance depends on its compressibility (or modulus) and thickness, care should be taken during drill and blast operations to minimize the damage to the cavern walls.

Fuel conditioning facility zone-to-zone transfer administrative controls

International Nuclear Information System (INIS)

Pope, C. L.

2000-01-01

The administrative controls associated with transferring containers from one criticality hazard control zone to another in the Argonne National Laboratory (ANL) Fuel Conditioning Facility (FCF) are described. FCF, located at the ANL-West site near Idaho Falls, Idaho, is used to remotely process spent sodium bonded metallic fuel for disposition. The process involves nearly forty widely varying material forms and types, over fifty specific use container types, and over thirty distinct zones where work activities occur. During 1999, over five thousand transfers from one zone to another were conducted. Limits are placed on mass, material form and type, and container types for each zone. Ml material and containers are tracked using the Mass Tracking System (MTG). The MTG uses an Oracle database and numerous applications to manage the database. The database stores information specific to the process, including material composition and mass, container identification number and mass, transfer history, and the operators involved in each transfer. The process is controlled using written procedures which specify the zone, containers, and material involved in a task. Transferring a container from one zone to another is called a zone-to-zone transfer (ZZT). ZZTs consist of four distinct phases, select, request, identify, and completion

Molecular differences in transition zone and peripheral zone prostate tumors

Science.gov (United States)

Sinnott, Jennifer A.; Rider, Jennifer R.; Carlsson, Jessica; Gerke, Travis; Tyekucheva, Svitlana; Penney, Kathryn L.; Sesso, Howard D.; Loda, Massimo; Fall, Katja; Stampfer, Meir J.; Mucci, Lorelei A.; Pawitan, Yudi; Andersson, Sven-Olof; Andrén, Ove

2015-01-01

Prostate tumors arise primarily in the peripheral zone (PZ) of the prostate, but 20–30% arise in the transition zone (TZ). Zone of origin may have prognostic value or reflect distinct molecular subtypes; however, it can be difficult to determine in practice. Using whole-genome gene expression, we built a signature of zone using normal tissue from five individuals and found that it successfully classified nine tumors of known zone. Hypothesizing that this signature captures tumor zone of origin, we assessed its relationship with clinical factors among 369 tumors of unknown zone from radical prostatectomies (RPs) and found that tumors that molecularly resembled TZ tumors showed lower mortality (P = 0.09) that was explained by lower Gleason scores (P = 0.009). We further applied the signature to an earlier study of 88 RP and 333 transurethral resection of the prostate (TURP) tumor samples, also of unknown zone, with gene expression on ~6000 genes. We had observed previously substantial expression differences between RP and TURP specimens, and hypothesized that this might be because RPs capture primarily PZ tumors, whereas TURPs capture more TZ tumors. Our signature distinguished these two groups, with an area under the receiver operating characteristic curve of 87% (P zones. Zone of origin may be important to consider in prostate tumor biomarker research. PMID:25870172

Degradation and stabilization of ice wedges: Implications for assessing risk of thermokarst in northern Alaska

Science.gov (United States)

Kanevskiy, Mikhail; Shur, Yuri; Jorgenson, Torre; Brown, Dana R. N.; Moskalenko, Nataliya; Brown, Jerry; Walker, Donald A.; Raynolds, Martha K.; Buchhorn, Marcel

2017-11-01

Widespread degradation of ice wedges has been observed during the last decades in numerous areas within the continuous permafrost zone of Eurasia and North America. To study ice-wedge degradation, we performed field investigations at Prudhoe Bay and Barrow in northern Alaska during 2011-2016. In each study area, a 250-m transect was established with plots representing different stages of ice-wedge degradation/stabilization. Field work included surveying ground- and water-surface elevations, thaw-depth measurements, permafrost coring, vegetation sampling, and ground-based LiDAR scanning. We described cryostratigraphy of frozen soils and stable isotope composition, analyzed environmental characteristics associated with ice-wedge degradation and stabilization, evaluated the vulnerability and resilience of ice wedges to climate change and disturbances, and developed new conceptual models of ice-wedge dynamics that identify the main factors affecting ice-wedge degradation and stabilization and the main stages of this quasi-cyclic process. We found significant differences in the patterns of ice-wedge degradation and stabilization between the two areas, and the patterns were more complex than those previously described because of the interactions of changing topography, water redistribution, and vegetation/soil responses that can interrupt or reinforce degradation. Degradation of ice wedges is usually triggered by an increase in the active-layer thickness during exceptionally warm and wet summers or as a result of flooding or disturbance. Vulnerability of ice wedges to thermokarst is controlled by the thickness of the intermediate layer of the upper permafrost, which overlies ice wedges and protects them from thawing. In the continuous permafrost zone, degradation of ice wedges rarely leads to their complete melting; and in most cases wedges eventually stabilize and can then resume growing, indicating a somewhat cyclic and reversible process. Stabilization of ice wedges

Geological modeling of a fault zone in clay rocks at the Mont-Terri laboratory (Switzerland)

Science.gov (United States)

Kakurina, M.; Guglielmi, Y.; Nussbaum, C.; Valley, B.

2016-12-01

Clay-rich formations are considered to be a natural barrier for radionuclides or fluids (water, hydrocarbons, CO2) migration. However, little is known about the architecture of faults affecting clay formations because of their quick alteration at the Earth's surface. The Mont Terri Underground Research Laboratory provides exceptional conditions to investigate an un-weathered, perfectly exposed clay fault zone architecture and to conduct fault activation experiments that allow explore the conditions for stability of such clay faults. Here we show first results from a detailed geological model of the Mont Terri Main Fault architecture, using GoCad software, a detailed structural analysis of 6 fully cored and logged 30-to-50m long and 3-to-15m spaced boreholes crossing the fault zone. These high-definition geological data were acquired within the Fault Slip (FS) experiment project that consisted in fluid injections in different intervals within the fault using the SIMFIP probe to explore the conditions for the fault mechanical and seismic stability. The Mont Terri Main Fault "core" consists of a thrust zone about 0.8 to 3m wide that is bounded by two major fault planes. Between these planes, there is an assembly of distinct slickensided surfaces and various facies including scaly clays, fault gouge and fractured zones. Scaly clay including S-C bands and microfolds occurs in larger zones at top and bottom of the Mail Fault. A cm-thin layer of gouge, that is known to accommodate high strain parts, runs along the upper fault zone boundary. The non-scaly part mainly consists of undeformed rock block, bounded by slickensides. Such a complexity as well as the continuity of the two major surfaces are hard to correlate between the different boreholes even with the high density of geological data within the relatively small volume of the experiment. This may show that a poor strain localization occurred during faulting giving some perspectives about the potential for

Stability analysis of high temperature superconducting coil in liquid hydrogen

International Nuclear Information System (INIS)

Nakayama, T.; Yagai, T.; Tsuda, M.; Hamajima, T.

2007-01-01

Recently, it is expected that hydrogen plays an important role in energy source including electric power in near future. Liquid hydrogen has high potential for cooling down superconducting coil wound with high temperature superconductors (HTS), such as BSCCO, YBCO. In this paper, we study stabilities of the coils wound with BSCCO tapes, which are immersed in the liquid hydrogen, and compare stability results with those cooled by liquid helium. We treat a minimum propagation zone (MPZ) theory to evaluate the coil stability considering boiling heat flux of the liquid hydrogen, and specific heat, heat conduction and resistivity of HTS materials as a function of temperature. It is found that the coil cooled by the liquid hydrogen has higher stability margin than that cooled by the liquid helium. We compare the stability margins of both coils wound with Bi-2223/Ag tape and Bi-2212/Ag tape in liquid hydrogen. As a result, it is found that the stability of Bi-2212 coil is equivalent to that of Bi-2223 coil in low and high magnetic field, while the maximum current of Bi-2212 coil exceeds a little bit that of Bi-2223 coil in both magnetic fields

Numerical Computation of Detonation Stability

KAUST Repository

Kabanov, Dmitry

2018-06-03

Detonation is a supersonic mode of combustion that is modeled by a system of conservation laws of compressible fluid mechanics coupled with the equations describing thermodynamic and chemical properties of the fluid. Mathematically, these governing equations admit steady-state travelling-wave solutions consisting of a leading shock wave followed by a reaction zone. However, such solutions are often unstable to perturbations and rarely observed in laboratory experiments. The goal of this work is to study the stability of travelling-wave solutions of detonation models by the following novel approach. We linearize the governing equations about a base travelling-wave solution and solve the resultant linearized problem using high-order numerical methods. The results of these computations are postprocessed using dynamic mode decomposition to extract growth rates and frequencies of the perturbations and predict stability of travelling-wave solutions to infinitesimal perturbations. We apply this approach to two models based on the reactive Euler equations for perfect gases. For the first model with a one-step reaction mechanism, we find agreement of our results with the results of normal-mode analysis. For the second model with a two-step mechanism, we find that both types of admissible travelling-wave solutions exhibit the same stability spectra. Then we investigate the Fickett’s detonation analogue coupled with a particular reaction-rate expression. In addition to the linear stability analysis of this model, we demonstrate that it exhibits rich nonlinear dynamics with multiple bifurcations and chaotic behavior.

Does the European financial stability bail out sovereigns or banks : An event study

NARCIS (Netherlands)

Horváth, Bálint; Huizinga, Harry

2015-01-01

On May 9, 2010 euro zone countries announced the creation of the European Financial Stability Facility. This paper investigates the impact of this announcement on bank share prices, bank credit default swap (CDS) spreads, and sovereign CDS spreads. The main private beneficiaries were bank creditors.

75 FR 51741 - Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Halibut and Sablefish Individual...

Science.gov (United States)

2010-08-23

... Program to provide economic stability for the Pacific halibut and sablefish commercial fisheries and.... 0906041011-91012-01 RIN 0648-AX91 Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Halibut and... designed to maintain the social character and economic benefits of the commercial, fixed-gear fisheries...

77 FR 29556 - Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Halibut and Sablefish Individual...

Science.gov (United States)

2012-05-18

... economic stability for the Pacific halibut and sablefish commercial fisheries and improve long-term.... 0906041011-2432-02] RIN 0648-AX91 Fisheries of the Exclusive Economic Zone Off Alaska; Pacific Halibut and... maintain the social character and economic benefits of the commercial, fixed-gear fisheries that Alaskan...

WorkZoneQ user guide for two-lane freeway work zones.

Science.gov (United States)

2013-06-01

WorkZoneQ was developed in Visual Basic for Applications (VBA) to implement the results of the previous study, : Queue and Users Costs in Highway Work Zones. This report contains the WorkZoneQ user guide. WorkZoneQ : consists of eight Excel ...

Influence of the spacers on the stability of channel cooled superconducting coils

International Nuclear Information System (INIS)

Meuris, C.

1980-10-01

In a previous paper, the thermal stability of channel cooled superconducting magnets was experimentally studied. Stable normal zones were observed within a range of currents and local disturbance energies. Usual theories fail to fully explain these results, owing to the fact that they take into account a heat transfer to liquid helium only function of the temperature of the conductor, whatever the position is. In a simplified theoretical analysis, it is shown that in a locally uncooled superconducting wire several stationary normal zones can exist. A criterion is derived that yields the recovery current as a function of the length of the uncooled region. Besides, a detailed numerical analysis determines the evolution of a normal zone in a channel cooled magnet. Theoretical calculations are compared with experimental results

ZoneLib

DEFF Research Database (Denmark)

Jessen, Jan Jacob; Schiøler, Henrik

2006-01-01

We present a dynamic model for climate in a livestock building divided into a number of zones, and a corresponding modular Simulink library (ZoneLib). While most literature in this area consider air flow as a control parameter we show how to model climate dynamics using actual control signals...... development of ZoneLib....

Assessment of additional impacts to environment during Ukryttya object stabilization works

International Nuclear Information System (INIS)

Klyuchnikov, A.A.; Shcherbin, V.N.; Rud'ko, V.M.; Batij, V.G.; Sizov, A.A.; Khavrus', V.G.

2004-01-01

Estimates of impact levels onto environment were made when implementing stabilization works of unstable building structures of Ukryttya object. The impact were evaluated to air water medium, as well to ground cover, social and technogenic environments. It was demonstrated, that impact levels to above environmental components under normal conditions of work implementation are negligible, and radioactive substance amount, which will penetrate into the environment, will make parts of percents to existing contamination of exclusion zone area. Estimates are also made of accident impacts onto environment, whose origination is probable during the stabilization works of Ukryttya object

Turbulent Non-Premixed Flames Stabilized on Double-Slit Curved Wall-Jet Burner with Simultaneous OH-Planar Laser-Induced Fluorescence and Particle Image Velocimetry Measurements

KAUST Repository

Mansour, Morkous S.; Chung, Suk-Ho

2015-01-01

, followed by a merged-jet region. The flames were stabilized in the recirculation zone and, in extreme cases, only a small flame seed remained in the recirculation zone. Together with the collision of the slit jets in the interaction jet region, the velocity

Microjet Injection Strategies for Mitigating Dynamics in a Lean Premixed Swirl-Stabilized Combustor

KAUST Repository

LaBry, Zachary; Shanbhogue, Santosh; Ghoniem, Ahmed

2011-01-01

Combustion dynamics remain a challenge in the development of low-emission, air-breathing combustors for power generation and aircraft propulsion. In this paper, we presenta parametric study on the use of microjet injectors for suppressing or mitigating the combustion dynamics that energize the thermoacoustic instability in a swirl-stabilized, premixed combustor. Microjet injectors consist of small inlet ports intended to inject flow with high momentum at relatively low mass flow rates into the flame-anchoring region. The microjets were configured to inject flow either axially, into the outer recirculation zone, or radially into the inner recirculation zone. Additionally, different injectors were tested with different relative senses of swirl (signs of angular momentum)with respect to the main flow: co-swirling, not swirling, or counter-swirling. We observed that injecting air or premixed fuel/air into the inner recirculation zone via counter-swirling radial microjets, we were able to reduce the overall sound pressure level in the combustor by over 20 dB in the lean end of the operating range. Other injector configurations were not observed to positively influence the combust or stability. Detailed PIV measurements are used to examine possible mechanisms of how the microjets impact the combustion dynamics, and the technology implications of our experiments are discussed.

Microjet Injection Strategies for Mitigating Dynamics in a Lean Premixed Swirl-Stabilized Combustor

KAUST Repository

LaBry, Zachary

2011-01-04

Combustion dynamics remain a challenge in the development of low-emission, air-breathing combustors for power generation and aircraft propulsion. In this paper, we presenta parametric study on the use of microjet injectors for suppressing or mitigating the combustion dynamics that energize the thermoacoustic instability in a swirl-stabilized, premixed combustor. Microjet injectors consist of small inlet ports intended to inject flow with high momentum at relatively low mass flow rates into the flame-anchoring region. The microjets were configured to inject flow either axially, into the outer recirculation zone, or radially into the inner recirculation zone. Additionally, different injectors were tested with different relative senses of swirl (signs of angular momentum)with respect to the main flow: co-swirling, not swirling, or counter-swirling. We observed that injecting air or premixed fuel/air into the inner recirculation zone via counter-swirling radial microjets, we were able to reduce the overall sound pressure level in the combustor by over 20 dB in the lean end of the operating range. Other injector configurations were not observed to positively influence the combust or stability. Detailed PIV measurements are used to examine possible mechanisms of how the microjets impact the combustion dynamics, and the technology implications of our experiments are discussed.

Influence of filling-drawdown cycles of the Vajont reservoir on Mt. Toc slope stability

Science.gov (United States)

Paronuzzi, Paolo; Rigo, Elia; Bolla, Alberto

2013-06-01

In the present work, the 1963 Vajont landslide has been back-analyzed in detail to examine the influence of reservoir operations (filling and drawdown) on Mt. Toc slope stability. The combined seepage-slope stability analyses carried out show that the main destabilizing factor that favored the 1963 Vajont landslide was the reservoir-induced water table that formed as a consequence of rapid seepage inflow within the submerged toe of the slope — decrease in the factor of safety (FOS) up to 12% compared to the initial slope stability condition, i.e., in the absence of the Vajont reservoir. Rainfall would only have been a decisive factor if the initial stability condition of the Mt. Toc slope had already been very close to failure (decrease in FOS caused by heavy or prolonged rainfall is about 3-4%, for the worst case scenario analyzed). The permeability of the shear zone material occurring at the base of the prehistoric Vajont rockslide has been evaluated at 5 × 10- 4 m/s, and back-calculated values of the friction angles Φ range from 17.5° to 27.5°. When considering mountain reservoirs, slope failures can occur during both filling and drawdown phases. In the Vajont case, owing to the highly permeable materials of the shear zone, slope stability decreased during filling and increased during drawdown. Another displacement-dependent phenomenon of a mechanical nature - progressive failure of the NE landslide constraint - has to be considered to understand the slope collapse that occurred during the last drawdown (26 September-9 October 1963). The results of the combined seepage-slope stability models indicate that permeability of bank-forming material and filling-drawdown rates of reservoirs can strongly influence slope stability. Slow lowering of the reservoir level is a necessary measure to reduce the occurrence of very dangerous transient negative peaks of FOS.

78 FR 36122 - Fisheries of the Exclusive Economic Zone Off Alaska; Bering Sea and Aleutian Islands Crab...

Science.gov (United States)

2013-06-17

... the harvesting and processing sectors'' and to monitor the ``economic stability for harvesters.... 120806311-3530-02] RIN 0648-BC25 Fisheries of the Exclusive Economic Zone Off Alaska; Bering Sea and... Tanner Crabs (FMP). These regulations revise the annual economic data reports (EDRs) currently required...

Empowerment Zones and Enterprise Districts - MDC_EnterpriseZone

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Polygon feature class of Miami Dade County Enterprise Zones. Enterprise Zones are special areas in the county where certain incentives from the State are available...

Water extraction and implications on soil moisture sensor placement in the root zone of banana

Directory of Open Access Journals (Sweden)

Alisson Jadavi Pereira da Silva

Full Text Available ABSTRACT: The knowledge on spatial and temporal variations of soil water storage in the root zone of crops is essential to guide the studies to determine soil water balance, verify the effective zone of water extraction in the soil and indicate the correct region for the management of water, fertilizers and pesticides. The objectives of this study were: (i to indicate the zones of highest root activity for banana in different development stages; (ii to determine, inside the zone of highest root activity, the adequate position for the installation of soil moisture sensors. A 5.0 m3 drainage lysimeter was installed in the center of an experimental area of 320 m2. Water extraction was quantified inside the lysimeter using a 72 TDR probe. The concept of time stability was applied to indicate the position for sensor installation within the limits of effective water extraction. There are two patterns of water extraction distribution during the development of banana and the point of installation of sensors for irrigation management inside the zone of highest root activity is not constant along the crop development.

Application Effect’s Research of Vetiver Eco Blanket in Pubugou Reservoir Fluctuating Zone

Directory of Open Access Journals (Sweden)

Lan Huijuan

2015-01-01

Full Text Available To solve the ecological disasters in Pubugou Reservoir Fluctuating Zone, ecological blanket governance model is proposed in this paper, which may provide good early environment for plants’ survival in fluctuation zone, and then play the function of greening and sustainable development to ensure the slopes’ stability. Meanwhile, based on the result of vetiver ecological blanket in Hanyuan experimental zone, we find that three kinds of typical Fluctuating Zone slope’s greening effect is good, which includes the dirt piling up slope, the whole lump of rock slope and the gravel piling up slope, and it gets an average coverage of 90.3 % as well as good strength. Due to the different geological conditions, the ecological blankets’ governance effect differs from slope to slope. Using analytic hierarchy process to calculate the weight, we get the dirt piling up slope, the whole lump of rock slope and the gravel piling up slope’s weights are 0.41, 0.17, 0.42, respectively, namely, the dirt piling up slope and the gravel piling up slope have good results overall, followed by the whole lump of rock slope.

Improving the treatment of non-aqueous phase TCE in low permeability zones with permanganate

Energy Technology Data Exchange (ETDEWEB)

Chokejaroenrat, Chanat, E-mail: chanat@sut.ac.th [Department of Civil Engineering, University of Nebraska, Lincoln, NE 68588-0531 (United States); School of Environmental Engineering, Institute of Engineering, Suranaree University of Technology, Nakhon Ratchasima 30000 (Thailand); Comfort, Steve, E-mail: scomfort1@unl.edu [School of Natural Resources, University of Nebraska, Lincoln, NE 68583-0915 (United States); Sakulthaew, Chainarong, E-mail: cvtcns@ku.ac.th [School of Natural Resources, University of Nebraska, Lincoln, NE 68583-0915 (United States); Department of Veterinary Technology, Kasetsart University, Bangkok 10900 (Thailand); Dvorak, Bruce, E-mail: bdvorak1@unl.edu [Department of Civil Engineering, University of Nebraska, Lincoln, NE 68588-0531 (United States)

2014-03-01

Graphical abstract: - Highlights: • Transport experiments used transmissive and low permeability zones (LPZs). • {sup 14}C-labeled TCE was used to quantify oxidation of DNAPL in LPZs by permanganate. • Stabilization aids prevented MnO{sub 2} rind formation. • DNAPL oxidation improved when xanthan and stabilization aids were used. - Abstract: Treating dense non-aqueous phase liquids (DNAPLs) embedded in low permeability zones (LPZs) is a particularly challenging issue for injection-based remedial treatments. Our objective was to improve the sweeping efficiency of permanganate (MnO{sub 4}{sup −}) into LPZs to treat high concentrations of TCE. This was accomplished by conducting transport experiments that quantified the penetration of various permanganate flooding solutions into a LPZ that was spiked with non-aqueous phase {sup 14}C-TCE. The treatments we evaluated included permanganate paired with: (i) a shear-thinning polymer (xanthan); (ii) stabilization aids that minimized MnO{sub 2} rind formation and (iii) a phase-transfer catalyst. In addition, we quantified the ability of these flooding solutions to improve TCE destruction under batch conditions by developing miniature LPZ cylinders that were spiked with {sup 14}C-TCE. Transport experiments showed that MnO{sub 4}{sup −} alone was inefficient in penetrating the LPZ and reacting with non-aqueous phase TCE, due to a distinct and large MnO{sub 2} rind that inhibited the TCE from further oxidant contact. By including xanthan with MnO{sub 4}{sup −}, the sweeping efficiency increased (90%) but rind formation was still evident. By including the stabilization aid, sodium hexametaphosphate (SHMP) with xanthan, permanganate penetrated 100% of the LPZ, no rind was observed, and the percentage of TCE oxidized increased. Batch experiments using LPZ cylinders allowed longer contact times between the flooding solutions and the DNAPL and results showed that SHMP + MnO{sub 4}{sup −} improved TCE destruction by �

Slip Zone versus Damage Zone Micromechanics, Arima-Takasuki Tectonic Line, Japan

Science.gov (United States)

White, J. C.; Lin, A.

2017-12-01

The Arima-Takasuki Tectonic Line (ATTL) of southern Honshu, Japan is defined by historically active faults and multiple splays producing M7 earthquakes. The damage zone of the ATTL comprises a broad zone of crushed, comminuted and pulverized granite/rhyolite1,2containing cm-scale slip zones and highly comminuted injection veins. In this presentation, prior work on the ATTL fault rocks is extending to include microstructural characterization by transmission electron microscopy (TEM) from recent trenching of the primary slip zone, as well as secondary slip zones. This is necessary to adequately characterize the extremely fine-grained material (typically less than 1mm) in both damage and core zones. Damage zone material exhibits generally random textures3 whereas slip zones are macroscopically foliated, and compositionally layered, notwithstanding a fairly homogeneous protolith. The latter reflects fluid-rock interaction during both coseismic and interseismic periods. The slip zones are microstructurally heterogeneous at all scales, comprising not only cataclasites and phyllosilicate (clay)-rich gouge zones, but Fe/Mn pellets or clasts that are contained within gouge. These structures appear to have rolled and would suggest rapid recrystallization and/or growth. A central question related to earthquake recurrence along existing faults is the nature of the gouge. In both near-surface exposures and ongoing drilling at depth, "plastic" or "viscous" gouge zones comprise ultra-fine-grained clay-siliciclastic particles that would not necessarily respond in a simple frictional manner. Depending on whether the plastic nature of these slip zones develops during or after slip, subsequent focusing of slip within them could be complicated. 1 Mitchell, T.A., Ben-Zion, Y., Shimamoto, T., 2011. Ear. Planet. Sci. Lett. 308, 284-297. 2 Lin, A., Yamashita, K, Tanaka, M. J., 2013. Struc. Geol. 48, 3-13. 3 White, J.C., Lin, A. 2016. Proc. AGU Fall Mtg., T42-02 San Francisco.

Simulation of longitudinal differential protection of transmission lines with additional stabilization and APU system

Directory of Open Access Journals (Sweden)

Rajić Tomislav D.

2016-01-01

Full Text Available This paper explains the algorithm for the longitudinal differential protection of transmission lines with automatic reclosing. Classic stabilization is not sufficient for avoiding of unnecessary operations caused by saturation of current transformer. This problem can occur during the fault plased outside of the protected zone of the transmission line. It is shown how unnecessary operation can occur during the outside fault whithout using of additional stabilization. The different types of faults were simulated and comparison of relay operations with and without additional stabilization is presented. The simulations were performed on the three-phase model of the transmission line formed by using of MATLAB/Simulink program.

Evaluation of Ohio work zone speed zones process.

Science.gov (United States)

2014-06-01

This report describes the methodology and results of analyses performed to determine the effectiveness of Ohio Department of Transportation processes for establishing work zone speed zones. Researchers observed motorists speed choice upstream of a...

Control and Stabilization of the Benjamin-Ono Equation in {L^2({{T})}}

Science.gov (United States)

Laurent, Camille; Linares, Felipe; Rosier, Lionel

2015-12-01

We study the control and stabilization of the Benjamin-Ono equation in {L^2({T})}, the lowest regularity where the initial value problem is well-posed. This problem was already initiated in Linares and Rosier (Trans Am Math Soc 367:4595-4626, 2015) where a stronger stabilization term was used (that makes the equation of parabolic type in the control zone). Here we employ a more natural stabilization term related to the L 2-norm. Moreover, by proving a theorem of controllability in L 2, we manage to prove the global controllability in large time. Our analysis relies strongly on the bilinear estimates proved in Molinet and Pilod (Anal PDE 5:365-395, 2012) and some new extension of these estimates established here.

Structural Stabilities of β-Ti Alloys Studied Using a New Mo Equivalent Derived from [ β/( α + β)] Phase-Boundary Slopes

Science.gov (United States)

Wang, Qing; Dong, Chuang; Liaw, Peter K.

2015-08-01

Structural stabilities of β-Ti alloys are generally investigated by an empirical Mo equivalent, which quantifies the stability contribution of each alloying element, M, in comparison to that of the major β-Ti stabilizer, Mo. In the present work, a new Mo equivalent (Moeq)Q is proposed, which uses the slopes of the boundary lines between the β and ( α + β) phase zones in binary Ti-M phase diagrams. This (Moeq)Q reflects a simple fact that the β-Ti stability is enhanced, when the β phase zone is enlarged by a β-Ti stabilizer. It is expressed as (Moeq)Q = 1.0 Mo + 0.74 V + 1.01 W + 0.23 Nb + 0.30 Ta + 1.23 Fe + 1.10 Cr + 1.09 Cu + 1.67 Ni + 1.81 Co + 1.42 Mn + 0.38 Sn + 0.34 Zr + 0.99 Si - 0.57 Al (at. pct), where the equivalent coefficient of each element is the slope ratio of the [ β/( α + β)] boundary line of the binary Ti-M phase diagram to that of the Ti-Mo. This (Moeq)Q is shown to reliably characterize the critical stability limit of multi-component β-Ti alloys with low Young's moduli, where the critical lower limit for β stabilization is (Moeq)Q = 6.25 at. pct or 11.8 wt pct Mo.

Application of GPR Method for Detection of Loose Zones in Flood Levee

Science.gov (United States)

Gołębiowski, Tomisław; Małysa, Tomasz

2018-02-01

In the paper the results of non-invasive georadar (GPR) surveys carried out for detection of loose zones located in the flood levee was presented. Terrain measurements were performed on the Vistula river flood levee in the village of Wawrzeńczyce near Cracow. In the investigation site, during the flood in 2010, leakages of levee were observed, so detection of inner water filtration paths was an important matter taking into account the stability of the levee during the next flood. GPR surveys had reconnaissance character, so they were carried out with the use of short-offset reflection profiling (SORP) technique and radargrams were subjected to standard signal processing. The results of surveys allowed to outline main loose zone in the levee which were the reason of leakages in 2010. Additionally gravel interbeddings in sand were detected which had an important influence, due to higher porosity of such zones, to water filtration inside of the levee. In the paper three solutions which allow to increase quality and resolution of radargrams were presented, i.e. changeable-polarisation surveys, advanced signal processing and DHA procedure.

A Unified Approach to Adaptive Neural Control for Nonlinear Discrete-Time Systems With Nonlinear Dead-Zone Input.

Science.gov (United States)

Liu, Yan-Jun; Gao, Ying; Tong, Shaocheng; Chen, C L Philip

2016-01-01

In this paper, an effective adaptive control approach is constructed to stabilize a class of nonlinear discrete-time systems, which contain unknown functions, unknown dead-zone input, and unknown control direction. Different from linear dead zone, the dead zone, in this paper, is a kind of nonlinear dead zone. To overcome the noncausal problem, which leads to the control scheme infeasible, the systems can be transformed into a m -step-ahead predictor. Due to nonlinear dead-zone appearance, the transformed predictor still contains the nonaffine function. In addition, it is assumed that the gain function of dead-zone input and the control direction are unknown. These conditions bring about the difficulties and the complicacy in the controller design. Thus, the implicit function theorem is applied to deal with nonaffine dead-zone appearance, the problem caused by the unknown control direction can be resolved through applying the discrete Nussbaum gain, and the neural networks are used to approximate the unknown function. Based on the Lyapunov theory, all the signals of the resulting closed-loop system are proved to be semiglobal uniformly ultimately bounded. Moreover, the tracking error is proved to be regulated to a small neighborhood around zero. The feasibility of the proposed approach is demonstrated by a simulation example.

Adaptive variable structure control for uncertain chaotic systems containing dead-zone nonlinearity

International Nuclear Information System (INIS)

Yan, J.-J.; Shyu, K.-K.; Lin, J.-S.

2005-01-01

This paper addresses a practical tracking problem for a class of uncertain chaotic systems with dead-zone nonlinearity in the input function. Based on the Lyapunov stability theorem and Barbalat lemma, an adaptive variable structure controller (AVSC) is proposed to ensure the occurrence of the sliding mode even though the control input contains a dead-zone. Also it is worthy of note that the proposed AVSC involves no information of the upper bound of uncertainty. Thus, the limitation of knowing the bound of uncertainty in advance is certainly released. Furthermore, in the sliding mode, the investigated uncertain chaotic system remains insensitive to the uncertainty, and behaves like a linear system. Finally, a well-known Duffing-Holmes chaotic system is used to demonstrate the feasibility of the proposed AVSC

Production of Low Cost Carbon-Fiber through Energy Optimization of Stabilization Process

Directory of Open Access Journals (Sweden)

Gelayol Golkarnarenji

2018-03-01

Full Text Available To produce high quality and low cost carbon fiber-based composites, the optimization of the production process of carbon fiber and its properties is one of the main keys. The stabilization process is the most important step in carbon fiber production that consumes a large amount of energy and its optimization can reduce the cost to a large extent. In this study, two intelligent optimization techniques, namely Support Vector Regression (SVR and Artificial Neural Network (ANN, were studied and compared, with a limited dataset obtained to predict physical property (density of oxidative stabilized PAN fiber (OPF in the second zone of a stabilization oven within a carbon fiber production line. The results were then used to optimize the energy consumption in the process. The case study can be beneficial to chemical industries involving carbon fiber manufacturing, for assessing and optimizing different stabilization process conditions at large.

Of floating-zone uranium; Sur l'uranium de zone flottante

Energy Technology Data Exchange (ETDEWEB)

Clottes, G [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1965-01-01

The floating zone method has been chosen in order to purify uranium. The various parameters occurring in this purification technique, have been studied theoretically and technologically. The speed that proves to be the most efficient is 0,7 cm/h, the direction can only upwards, and the fusion must take place under pressure of 10{sup -7} Torr or so. Besides such problems concerning purification, the study of the floating zone stability led us to define a field touching the size and diameter of uranium drops, which, on the one hand coincides with Heywang's conditions and, on the other hand, is compatible with a fusion in the core of the bar. Such field shows that the floating zone can easily apply to bars whose diameter is included between 5 and 10 mm, and that it cannot work out when the diameter exceeds 21 mm. The apparatus, consisting in a means of heating by electronic bombardment under ultra-vacuum is conditioned by the various parameters that have been studied. As the analysis results were insufficient, the uranium thus dealt with has been characterized by metallurgic and physical tests: micrographic tests, measures of microhardness, measures of electric resistivity at a low temperature, have shown a definite purification at the bar-head; these results have been confirmed by the lowering at 270 C of the temperature of recrystallization together with the definite tendency of the refined metal to polygonize. The measures of electric resistivity constitute an easy and quantitative way of figuring out the metal purity. The influence of an impurity on the electric resistivity of uranium has been studied by U-Au alloys with a weak concentration of gold. The two important following points are brought out be these experiences: 1 - the measure of electric resistivity should be worked out on anneal bars in {gamma} phase and cooled. 2 - Gold has a very strong influence on uranium; the value 500 {mu}{omega}cm per cent of gold enabled us to give a total concentration of 20

Cathodic polarization as a mean to stabilize physical parameters of underground pipelines

International Nuclear Information System (INIS)

Skritskij, R.R.

1993-01-01

Possibilities of further utilization of old gas-pipelines are determined. The investigations conducted confirm the conclusions of the previous researches on the stabilizing and improving effect of cathode polarization on the physico-mechanical properties of gas pipeline steel. Efficient and constant electrochemical protection of gas pipelines with the expired or close to expiration life time stabilizers and improves the basic physicomechanical properties of pipeline steel: ultimate strength and yield point, relative stretching. The same refers to impact strength. Degradation of physico-mechanical properties of gas pipeline steel is observed only in the zone of the welded joint

Layout Determining Features, their Influence Zones and Respect Distances at the Olkiluoto Site

International Nuclear Information System (INIS)

Pere, T.; Ahokas, H.; Vaittinen, T.; Wikstroem, L.

2012-12-01

Fault zones located at the site of an underground nuclear waste repository may pose a risk to the repository by acting as potential hosts for earthquakes during the present day or future stress fields and having the possibility to induce secondary displacements on nearby large fractures, which may damage the nuclear waste canisters, if being intersected by such fractures. The fault zones may additionally provide possible flow routes, important for the transport of radionuclides and the chemical stability of the repository. It is therefore important to identify such structures, defined as layout determining features (LDF), and to assess their influence on the surrounding host rock and to determine respect volumes to the structures, which are avoided in the layout planning in order to mitigate the possible harmful effects to the repository. Fault zones with a trace length of 3 km or more are considered as layout determining features as these can potentially host an earthquake of a magnitude of 5.5 or more and may thus induce secondary displacements larger than 5 cm on nearby fractures, which is held as the current canister damage threshold premise. Fault zones with a size less than 3 km are considered unlikely candidates to induce secondary displacements of 5 cm or larger. In addition to the earthquake potential, hydrogeological zones with high T -value (geometrical mean T ≤ 10 -6 m 2 /s) and large dimensions (at least several hundred metres) are also defined as layout determining features. For each layout determining feature an influence zone is defined, depicting a volume around a fault zone or a hydrogeological zone with increased fracture density and permeability, often also called as damage zones in the scientific literature. Influence zones are therefore considered as mechanically weak and/or transmissive parts of the host rock, which may cause harmful effects to the performance of the repository if intersecting deposition tunnels or deposition holes. In

Linear stability of microtearing modes in ASDEX

International Nuclear Information System (INIS)

Giannone, L.

1987-12-01

The linear stability of microtearing modes in typical ASDEX discharges have been calculated. In the case of Ohmic discharges it was found that unstable modes are predicted to be located towards the centre of the plasma. For L and H discharges the zone of instability shifts towards the plasma edge. The interpretation of an increase or decrease in the amplitude of broadband magnetic fluctuations during L and H discharges must be interpreted with caution, since the amplitude observed is strongly dependent on the radial position of the instability. (orig./GG)

A New Paradigm for Habitability in Planetary Systems: the Extremophilic Zone

Science.gov (United States)

Janot-Pacheco, E., Bernardes, L., Lage, C. A. S.

2014-03-01

More than a thousand exoplanets have been discovered so far. Planetary surface temperature may strongly depends on its albedo and geodynamic conditions. We have fed exoplanets from the Encyclopedia database with a comprehensive model of Earth's atmosphere and plate tectonics. As CO2 is the main agent responsible for the greenhouse effect, its partial pressure has been taken as a free parameter to estimate the surface temperature of some known planets. We also investigated the possible presence of "exomoons" belonging to giant planets in the Habitable Zone capable of harbour dynamic stability, to retain an atmosphere and to keep geodynamic activity for long time spans. Biological data on earthly micro-organisms classified as "extremophiles" indicate that such kind of microbial species could dwell on the surface of many exoplanets and exomoons. We thus propose an extension of the mainly astronomically defined "Habitable Zone" concept into the more astrobiologically one, the "Extremophililic Zone", that takes into account other parameters allowing survival of more robust life forms. This contribution comes from an ongoing project developed by a French-Brazilian colaboration in Astrophysics and Biophysics to search for living fingerprints in astrobiologically promising exoplanets.

Effects of inserted depth of wall penetration on basal stability of foundation pits

Science.gov (United States)

Zhou, Aizhao; Shen, Hao; Sun, Jinguo

2017-05-01

Evaluation of basal heave stability is one of important design checks for excavations in soft clays. The commonly used classical calculation method based on limit equilibrium theory and the safety coefficient formula recommended by the current code, do not consider the influence of supporting structure of foundation pit depth heave stability, which results in conservative. Considering the wall stiffness and strength, the effective stress changes in different depth of soil, the frictional resistance between the retaining wall and the passive zone, the vertical shear resistance of the soil behind the wall and other factors. The modified safety factor calculation formula of foundation pit stability is presented, comparison analysis of calculation method combined with examples. The calculation results show that the safety factor of foundation pit stability is improved considering the influence of supporting structure depth, the calculation results are more reasonable.

Fault zone hydrogeology

Science.gov (United States)

Bense, V. F.; Gleeson, T.; Loveless, S. E.; Bour, O.; Scibek, J.

2013-12-01

Deformation along faults in the shallow crust (research effort of structural geologists and hydrogeologists. However, we find that these disciplines often use different methods with little interaction between them. In this review, we document the current multi-disciplinary understanding of fault zone hydrogeology. We discuss surface- and subsurface observations from diverse rock types from unlithified and lithified clastic sediments through to carbonate, crystalline, and volcanic rocks. For each rock type, we evaluate geological deformation mechanisms, hydrogeologic observations and conceptual models of fault zone hydrogeology. Outcrop observations indicate that fault zones commonly have a permeability structure suggesting they should act as complex conduit-barrier systems in which along-fault flow is encouraged and across-fault flow is impeded. Hydrogeological observations of fault zones reported in the literature show a broad qualitative agreement with outcrop-based conceptual models of fault zone hydrogeology. Nevertheless, the specific impact of a particular fault permeability structure on fault zone hydrogeology can only be assessed when the hydrogeological context of the fault zone is considered and not from outcrop observations alone. To gain a more integrated, comprehensive understanding of fault zone hydrogeology, we foresee numerous synergistic opportunities and challenges for the discipline of structural geology and hydrogeology to co-evolve and address remaining challenges by co-locating study areas, sharing approaches and fusing data, developing conceptual models from hydrogeologic data, numerical modeling, and training interdisciplinary scientists.

The role of vegetation on gully erosion stabilization at a severely degraded landscape: A case study from Calhoun Experimental Critical Zone Observatory

Science.gov (United States)

Bastola, S.; Dialynas, Y. G.; Bras, R. L.; Noto, L. V.; Istanbulluoglu, E.

2018-05-01

Gully erosion was evidence of land degradation in the southern Piedmont, site of the Calhoun Critical Zone Observatory (CCZO), during the cotton farming era. Understanding of the underlying gully erosion processes is essential to develop gully erosion models that could be useful in assessing the effectiveness of remedial and soil erosion control measures such as gully backfilling, revegetation, and terracing. Development and validation of process-based gully erosion models is difficult because observations of the formation and progression of gullies are limited. In this study, analytic formulations of the two dominant gullying processes, namely, plunge pool erosion and slab failure, are utilized to simulate the gullying processes in the 4-km2 Holcombe's Branch watershed. In order to calibrate parameters of the gully erosion model, gully features (e.g., depth and area) extracted from a high-resolution LiDAR map are used. After the calibration, the gully model is able to delineate the spatial extent of gullies whose statistics are in close agreement with the gullies extracted from the LiDAR DEM. Several simulations with the calibrated model are explored to evaluate the effectiveness of various gully remedial measures, such as backfilling and revegetation. The results show that in the short-term, the reshaping of the topographical surface by backfilling and compacting gullies is effective in slowing down the growth of gullies (e.g., backfilling decreased the spatial extent of gullies by 21-46% and decreased the average depth of gullies by up to 9%). Revegetation, however, is a more effective approach to stabilizing gullies that would otherwise expand if no gully remedial measures are implemented. Analyses of our simulations show that the gully stabilization effect of revegetation varies over a wide range, i.e., leading to 23-69% reduction of the spatial extent of gullies and up to 45% reduction in the depth of gullies, depending on the selection of plant species and

Modeling foam delivery mechanisms in deep vadose-zone remediation using method of characteristics

Energy Technology Data Exchange (ETDEWEB)

Roostapour, A. [Craft and Hawkins Department of Petroleum Engineering, Louisiana State University, Baton Rouge, LA 70803 (United States); Kam, S.I., E-mail: kam@lsu.edu [Craft and Hawkins Department of Petroleum Engineering, Louisiana State University, Baton Rouge, LA 70803 (United States)

2012-12-15

Highlights: Black-Right-Pointing-Pointer A new mathematical framework established for vadose-zone foam remediation. Black-Right-Pointing-Pointer Graphical solutions presented by Method of Characteristics quantitatively. Black-Right-Pointing-Pointer Effects of design parameters in the field applications thoroughly investigated. Black-Right-Pointing-Pointer Implication of modeling study for successful field treatment discussed. - Abstract: This study investigates foam delivery mechanisms in vadose-zone remediation by using Method of Characteristics (MoC), a mathematical tool long been used for the analysis of miscible and immiscible flooding in porous media in petroleum industry. MoC converts the governing material-balance partial differential equations into a series of ordinary differential equations, and the resulting solutions are in a form of wave propagation (more specifically, for chemical species and phase saturations) through the system as a function of time and space. Deep vadose-zone remediation has special features compared to other conventional remediation applications. They include, not limited to, a high level of heterogeneity, a very dry initial condition with low water saturation (S{sub w}), pollutants such as metals and radionuclides fully dissolved in groundwater, and a serious concern about downward migration during the remediation treatments. For the vadose-zone remediation processes to be successful, the injected aqueous phase should carry chemicals to react with pollutants and precipitate them for immobilization and stabilization purposes. As a result, foams are believed to be an effective means, and understanding foam flow mechanism in situ is a key to the optimal design of field applications. Results show that foam delivery mechanism is indeed very complicated, making the optimum injection condition field-specific. The five major parameters selected (i.e., initial saturation of the medium, injection foam quality, surfactant adsorption, foam

Modeling foam delivery mechanisms in deep vadose-zone remediation using method of characteristics

International Nuclear Information System (INIS)

Roostapour, A.; Kam, S.I.

2012-01-01

Highlights: ► A new mathematical framework established for vadose-zone foam remediation. ► Graphical solutions presented by Method of Characteristics quantitatively. ► Effects of design parameters in the field applications thoroughly investigated. ► Implication of modeling study for successful field treatment discussed. - Abstract: This study investigates foam delivery mechanisms in vadose-zone remediation by using Method of Characteristics (MoC), a mathematical tool long been used for the analysis of miscible and immiscible flooding in porous media in petroleum industry. MoC converts the governing material-balance partial differential equations into a series of ordinary differential equations, and the resulting solutions are in a form of wave propagation (more specifically, for chemical species and phase saturations) through the system as a function of time and space. Deep vadose-zone remediation has special features compared to other conventional remediation applications. They include, not limited to, a high level of heterogeneity, a very dry initial condition with low water saturation (S w ), pollutants such as metals and radionuclides fully dissolved in groundwater, and a serious concern about downward migration during the remediation treatments. For the vadose-zone remediation processes to be successful, the injected aqueous phase should carry chemicals to react with pollutants and precipitate them for immobilization and stabilization purposes. As a result, foams are believed to be an effective means, and understanding foam flow mechanism in situ is a key to the optimal design of field applications. Results show that foam delivery mechanism is indeed very complicated, making the optimum injection condition field-specific. The five major parameters selected (i.e., initial saturation of the medium, injection foam quality, surfactant adsorption, foam strength, and foam stability) are shown to be all important, interacting with each other. Results also

Soil monitoring in agro-ecosystems of high mountain zone in Quindio

International Nuclear Information System (INIS)

Sadeghian, Siavosh; Orozco, O l; Murgueitio, E

2001-01-01

Were evaluated soil characteristics in 4 common agro-ecosystems of high mountain zone of Quindio department, soil forest exhibit better indicators that others systems. Low macro porosity and hydraulic conductivity were consequences more important of cattle ranching systems. In pinus plantations were registered lower value of organic matter, pH, interchanging bases, gravimetric moisture and microbial activity CO 2 . As a result of pinus establishment on pasture ground increase drainable porosity and hydraulic conductivity. In granadilla cultivation were lower organism diversity and structural stability

Operational Limitations of Arctic Waste Stabilization Ponds: Insights from Modeling Oxygen Dynamics and Carbon Removal

DEFF Research Database (Denmark)

Ragush, Colin M.; Gentleman, Wendy C.; Hansen, Lisbeth Truelstrup

2018-01-01

Presented here is a mechanistic model of the biological dynamics of the photic zone of a single-cell arctic waste stabilization pond (WSP) for the prediction of oxygen concentration and the removal of oxygen-demanding substances. The model is an exploratory model to assess the limiting environmen...

33 CFR 165.169 - Safety and Security Zones: New York Marine Inspection Zone and Captain of the Port Zone.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety and Security Zones: New... Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PORTS AND WATERWAYS SAFETY... Areas First Coast Guard District § 165.169 Safety and Security Zones: New York Marine Inspection Zone...

33 CFR 165.814 - Security Zones; Captain of the Port Houston-Galveston Zone.

Science.gov (United States)

2010-07-01

... Port Houston-Galveston Zone. 165.814 Section 165.814 Navigation and Navigable Waters COAST GUARD... § 165.814 Security Zones; Captain of the Port Houston-Galveston Zone. (a) Location. The following areas are designated as security zones: (1) Houston, Texas. The Houston Ship Channel and all associated...

Stability analysis of a recycling circuit of a BWR type reactor. Theoretical study

International Nuclear Information System (INIS)

Salinas H, J.G.; Espinosa P, G.; Gonzalez M, V.M.

2000-01-01

The Technology, Regulation and Services Management of the National Commission of Nuclear Safety and Safeguards financed and in coordinate form with the I.P.H. Department of the Metropolitan Autonomous-Iztapalapa University developed the present project with the purpose of studying the effect of the recycling system on the linear stability of a BWR reactor whose reference central is the Laguna Verde power station. The present project forms part of a work series focused to the linear stability of the nuclear reactor of the Unit 1 at Laguna Verde power station. The components of the recycling system considered for the study of stability are the recycling external circuit (recycling pumps, valves) and the internal circuit (downcomer, jet pumps, lower full, driers, separators). The mathematical model is obtained applying mass balances and movement quantity in each one of the mentioned circuits. With respect to the nucleus model two regions are considered, the first one is made of a flow in one phase and the second one of a flow in two phases. For modelling the biphasic region it is considered homogenous flow. Generally it is studied the system behavior in the frequency domain starting from the transfer function applied to four operational states which correspond to the lower stability zone in the map power-flow of the Unit 1 of Laguna Verde power station. The Nyquist diagrams corresponding to each state as well as their characteristic frequency were determined. The results show that exists a very clear dependence of the power-flow relation on the stability of the system. It was found that the boiling length is an important parameter for the linear stability of the system. The obtained results show that the characteristic frequencies in unstability zones are similar to the reported data of the Unit 1 of the Laguna Verde power station in the event of power oscillations carried out in January 1995. (Author)

Adaptive NN tracking control of uncertain nonlinear discrete-time systems with nonaffine dead-zone input.

Science.gov (United States)

Liu, Yan-Jun; Tong, Shaocheng

2015-03-01

In the paper, an adaptive tracking control design is studied for a class of nonlinear discrete-time systems with dead-zone input. The considered systems are of the nonaffine pure-feedback form and the dead-zone input appears nonlinearly in the systems. The contributions of the paper are that: 1) it is for the first time to investigate the control problem for this class of discrete-time systems with dead-zone; 2) there are major difficulties for stabilizing such systems and in order to overcome the difficulties, the systems are transformed into an n-step-ahead predictor but nonaffine function is still existent; and 3) an adaptive compensative term is constructed to compensate for the parameters of the dead-zone. The neural networks are used to approximate the unknown functions in the transformed systems. Based on the Lyapunov theory, it is proven that all the signals in the closed-loop system are semi-globally uniformly ultimately bounded and the tracking error converges to a small neighborhood of zero. Two simulation examples are provided to verify the effectiveness of the control approach in the paper.

GOVERNING EUROPEAN UNION TO FINANCIAL STABILITY

Directory of Open Access Journals (Sweden)

Ion-Lucian CATRINA

2012-09-01

Full Text Available In the last four years, a significant part of the European Union members has recorded a real decline in the sustainability of their public debt. The failure of Greece, Italy, Belgium or Spain to easily find funding at previous interest rates has induced the fear that the European Monetary Union would disintegrate. Such as scenario is not realistic because does not take into account the economic interdependencies that have been created between the countries participating at the monetary zone. Nevertheless, we can say that the Stability and Growth Pact which aimed towards the coordination of national fiscal policies for ensuring the stability and prudence of the budgetary climate, has failed. This failure was primarily due to the lack of specific sanctions for those members that have not fought against the fiscal imbalances and secondly to the stopping the steps forward towards a common fiscal policy. Thus, we can say that the European Monetary Union is driven now by the wrong rule of “no taxation with representation”. For these reasons, this paper aims at showing that the European fiscal federalism is still far away from becoming reality and that the new instruments chosen for the new stability of the European Monetary Union will be the task of the Member States themselves. This paper will also review the main rules that are projected to be the source for the future European financial stability and growth: the balanced budgets and the deficits built only on the “Golden Rule” premises, for which other amendments on European Treaties are expected.

Galactic evolution with self-regulated star formation - Stability of a simple one-zone model

International Nuclear Information System (INIS)

Parravano, A.; Rosenzweig, P.; Teran, M.

1990-01-01

In a simple one-zone model of mass exchange between three components (stars, clouds, and diffused gas), a self-regulating mechanism based on the sensitivity of the condensation of small cool clouds upon the radiation density in the 912-1100 A band is presently included. This mechanism is capable of affecting the large-scale structure of the galaxies due to the fact that it acts at a large scale in a very short time. Even in the most favorable models for the production of nonlinear oscillations, the inclusion of this mechanism of self-regulation leads, in many cases, to the progressive damping of the oscillations. 26 refs

The prevalence of serum antibodies to tick-borne infections in Mbale District, Uganda: The effect of agro-ecological zone, grazing management and age of cattle

Directory of Open Access Journals (Sweden)

C. Rubaire-Akiiki

2004-03-01

Full Text Available Between August and October 2000, a cross-sectional study was conducted in smallholder dairy farms in Mbale District, Uganda to assess the prevalence of ticks and tick-borne diseases under different grazing systems and agro-ecological zones and understand the circumstances under which farmers operated. A questionnaire was administered to obtain information on dairy farm circumstances and practices. A total of 102 farms were visited and sera and ticks were collected from 478 animals. Sero-prevalence of tick-borne diseases was determined using an enzyme-linked immunoassay. Acaricides were used indiscriminately but the intensity of their use varied with the grazing system and zone. Cattle from different farms mixed for various reasons. During the dry seasons farmers have to get additional fodder from outside their farms that can result in importation of ticks. The prevalence of ticks and serum antibodies to tick-borne infections differed across the grazing systems and zones. The highest serum antibody prevalence (>60% was recorded in the lowland zone under the free range and tethering grazing systems. The lowest tick challenge and serum antibody levels (<50% were recorded in the midland and upland zones under a zero-grazing system. These findings suggest that endemic stability to East Coast Fever, babesiosis and anaplasmosis is most likely to have existed in the lowland zone, particularly, under the tethering and free-range grazing systems. Also, endemic stability for babesiosis existed in the upland zones. Endemic instability for East Coast Fever existed in the midland and upland zones. These structured observational studies are instrumental in planning of control strategies for ticks and tick borne diseases since production systems and the cattle population at high risk of the diseases in the district have been identified.

Greece – in the centre of sovereign debt crisis. Consequences on the evolution of Euro Zone economies

Directory of Open Access Journals (Sweden)

Cristina Bâlgăr

2011-10-01

Full Text Available The purpose of this paper is to present the evolution of economic and financial crisis in Greece. We will examine the effect of Hellenic crisis on deepening the sovereign debt crisis in Euro zone and the possible consequences across the entire European economy. The research also aims to present possible scenarios of evolution for the Greek crisis and their potential consequences for the stability and economic growth perspectives in European Union. Our research concludes by highlighting the consequences of economic measures imposed to Greece by the European Union for the consolidation and fiscal stabilization of Hellenic economy.

Destabilization, Propagation, and Generation of Surfactant-Stabilized Foam during Crude Oil Displacement in Heterogeneous Model Porous Media.

Science.gov (United States)

Xiao, Siyang; Zeng, Yongchao; Vavra, Eric D; He, Peng; Puerto, Maura; Hirasaki, George J; Biswal, Sibani L

2018-01-23

Foam flooding in porous media is of increasing interest due to its numerous applications such as enhanced oil recovery, aquifer remediation, and hydraulic fracturing. However, the mechanisms of oil-foam interactions have yet to be fully understood at the pore level. Here, we present three characteristic zones identified in experiments involving the displacement of crude oil from model porous media via surfactant-stabilized foam, and we describe a series of pore-level dynamics in these zones which were not observed in experiments involving paraffin oil. In the displacement front zone, foam coalesces upon initial contact with crude oil, which is known to destabilize the liquid lamellae of the foam. Directly upstream, a transition zone occurs where surface wettability is altered from oil-wet to water-wet. After this transition takes place, a strong foam bank zone exists where foam is generated within the porous media. We visualized each zone using a microfluidic platform, and we discuss the unique physicochemical phenomena that define each zone. In our analysis, we also provide an updated mechanistic understanding of the "smart rheology" of foam which builds upon simple "phase separation" observations in the literature.

The Sorong Fault Zone, Indonesia: Mapping a Fault Zone Offshore

Science.gov (United States)

Melia, S.; Hall, R.

2017-12-01

The Sorong Fault Zone is a left-lateral strike-slip fault zone in eastern Indonesia, extending westwards from the Bird's Head peninsula of West Papua towards Sulawesi. It is the result of interactions between the Pacific, Caroline, Philippine Sea, and Australian Plates and much of it is offshore. Previous research on the fault zone has been limited by the low resolution of available data offshore, leading to debates over the extent, location, and timing of movements, and the tectonic evolution of eastern Indonesia. Different studies have shown it north of the Sula Islands, truncated south of Halmahera, continuing to Sulawesi, or splaying into a horsetail fan of smaller faults. Recently acquired high resolution multibeam bathymetry of the seafloor (with a resolution of 15-25 meters), and 2D seismic lines, provide the opportunity to trace the fault offshore. The position of different strands can be identified. On land, SRTM topography shows that in the northern Bird's Head the fault zone is characterised by closely spaced E-W trending faults. NW of the Bird's Head offshore there is a fold and thrust belt which terminates some strands. To the west of the Bird's Head offshore the fault zone diverges into multiple strands trending ENE-WSW. Regions of Riedel shearing are evident west of the Bird's Head, indicating sinistral strike-slip motion. Further west, the ENE-WSW trending faults turn to an E-W trend and there are at least three fault zones situated immediately south of Halmahera, north of the Sula Islands, and between the islands of Sanana and Mangole where the fault system terminates in horsetail strands. South of the Sula islands some former normal faults at the continent-ocean boundary with the North Banda Sea are being reactivated as strike-slip faults. The fault zone does not currently reach Sulawesi. The new fault map differs from previous interpretations concerning the location, age and significance of different parts of the Sorong Fault Zone. Kinematic

A two-dimensional time domain near zone to far zone transformation

Science.gov (United States)

Luebbers, Raymond J.; Ryan, Deirdre; Beggs, John H.; Kunz, Karl S.

1991-01-01

In a previous paper, a time domain transformation useful for extrapolating 3-D near zone finite difference time domain (FDTD) results to the far zone was presented. In this paper, the corresponding 2-D transform is outlined. While the 3-D transformation produced a physically observable far zone time domain field, this is not convenient to do directly in 2-D, since a convolution would be required. However, a representative 2-D far zone time domain result can be obtained directly. This result can then be transformed to the frequency domain using a Fast Fourier Transform, corrected with a simple multiplicative factor, and used, for example, to calculate the complex wideband scattering width of a target. If an actual time domain far zone result is required it can be obtained by inverse Fourier transform of the final frequency domain result.

Root zone effects on tracer migration in arid zones

International Nuclear Information System (INIS)

Tyler, S.W.; Walker, G.R.

1994-01-01

The study of groundwater recharge and soil water movement in arid regions has received increased attention in the search for safe disposal sites for hazardous wastes. In passing through the upper 1 to 2 m of most soil profiles, tracers indicative of recharge such as Cl, 2 H, 18 O, Br, 3 H, and 56 Cl are subjected to a wide range of processes not encountered deeper in the profile. This transition zone, where water enters as precipitation and leaves as recharge, is often ignored when environmental tracers are used to estimate deep soil water flux and recharge, yet its effect may be profound. In this work, we reexamine the processes of root extraction and its effect on the velocity and distribution of tracers. Examples are presented for idealized conditions, which show clearly the relation between the root zone processes and the deep drainage or recharge. The results indicate that, when recharge is small and root zone processes are not accounted for, tracer techniques can significantly overestimate recharge until the tracer has moved well below the root zone. By incorporating simple models of root zone processes, a clearer understanding of tracer distributions and a more accurate estimate of recharge can then be made. 11 refs., 9 figs

75 FR 50700 - Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, and Drawbridge...

Science.gov (United States)

2010-08-17

...] Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, and Drawbridge Operation... notice lists temporary safety zones, security zones, special local regulations, and drawbridge operation... responsive to the safety and security needs within their jurisdiction; therefore, District Commanders and...

Radiant zone heated particulate filter

Science.gov (United States)

Gonze, Eugene V [Pinckney, MI

2011-12-27

A system includes a particulate matter (PM) filter including an upstream end for receiving exhaust gas and a downstream end. A radiant zoned heater includes N zones, where N is an integer greater than one, wherein each of the N zones includes M sub-zones, where M is an integer greater than or equal to one. A control module selectively activates at least a selected one of the N zones to initiate regeneration in downstream portions of the PM filter from the one of the N zones, restricts exhaust gas flow in a portion of the PM filter that corresponds to the selected one of the N zones, and deactivates non-selected ones of the N zones.

The effect of effective microorganisms (EM on EBPR in modified contact stabilization system

Directory of Open Access Journals (Sweden)

Ehab M. Rashed

2015-12-01

Full Text Available Excessive phosphorus can cause eutrophication in water bodies and needs to be reduced in most wastewaters before discharge to receiving waters. The enhanced biological phosphorus removal (EBPR process has been shown to be an economical and environmentally compatible method for reducing phosphorus from wastewaters. The experiment has been performed in order to investigate the effect of using effective microorganisms (EM as an application of Enhanced Biological Phosphorous Removal (EBPR in modified contact stabilization activated sludge system by using contact tank as a phosphorus uptake zone and using thickener tank as a phosphorus release zone. The study involved the construction of a pilot plant which was setup in the Quhafa Wastewater Treatment Plant (WWTP, Al Fayoum, Egypt. Then the uptake and release of total phosphorus were determined through two batch tests using sludge samples from thickener and stabilization tanks. Results showed the removal efficiencies of Chemical Oxygen Demand (COD, Biological Oxygen Demand (BOD5 and total phosphorus (TP of this pilot plant were 93%, 93% and 90%, respectively. On the other hand the results of batch tests showed that the reason for high ability of phosphorus removal by this pilot plant is related to the high performance of microorganisms for phosphorus accumulation. Finally providing activated EM to the anaerobic zone was to improve fermentation by achieving the enhancement of the performance of phosphorus accumulating organisms (PAOs and then increase phosphorous release resulting in the decrease of the average effluent phosphorus concentration.

An alternative soil nailing system for slope stabilization: Akarpiles

Science.gov (United States)

Lim, Chun-Lan; Chan, Chee-Ming

2017-11-01

This research proposes an innovative solution for slope stabilization with less environmental footprint: AKARPILES. In Malaysia, landslide has become common civil and environmental problems that cause impacts to the economy, safety and environment. Therefore, effective slope stabilization method helps to improve the safety of public and protect the environment. This study focused on stabilizing surfacial slope failure. The idea of AKARPILES was generated from the tree roots system in slope stabilization. After the piles are installed in the slope and intercepting the slip plane, grout was pumped in and discharged through holes on the piles. The grout then filled the pores in the soil with random flow within the slip zone. SKW mixture was used to simulate the soil slope. There were two designs being proposed in this study and the prototypes were produced by a 3D printer. Trial mix of the grout was carried out to obtain the optimum mixing ratio of bentonite: cement: water. A series of tests were conducted on the single-pile-reinforced slope under vertical slope crest loading condition considering different slope gradients and nail designs. Parameters such as ultimate load, failure time and failure strain were recorded and compared. As comparison with the unreinforced slope, both designs of AKARPILES showed better but different performances in the model tests.

A note on the effect of fault gouge thickness on fault stability

Science.gov (United States)

Byerlee, J.; Summers, R.

1976-01-01

At low confining pressure, sliding on saw cuts in granite is stable but at high pressure it is unstable. The pressure at which the transition takes place increases if the thickness of the crushed material between the sliding surfaces is increased. This experimental result suggests that on natural faults the stability of sliding may be affected by the width of the fault zone. ?? 1976.

Towards stacked zone plates

International Nuclear Information System (INIS)

Werner, S; Rehbein, S; Guttman, P; Heim, S; Schneider, G

2009-01-01

Fresnel zone plates are the key optical elements for soft and hard x-ray microscopy. For short exposure times and minimum radiation load of the specimen the diffraction efficiency of the zone plate objectives has to be maximized. As the efficiency strongly depends on the height of the diffracting zone structures the achievable aspect ratio of the nanostructures determines these limits. To reach aspect ratios ≥ 20:1 for high efficient optics we propose to superimpose zone plates on top of each other. With this multiplication approach the final aspect ratio is only limited by the number of stacked zone plate layers. For the stack process several nanostructuring process steps have to be developed and/or improved. Our results show for the first time two layers of zone plates stacked on top of each other.

76 FR 70342 - Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation...

Science.gov (United States)

2011-11-14

...] Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation... published in the Federal Register. This notice lists temporary safety zones, security zones, special local... Commanders and Captains of the Port (COTP) must be immediately responsive to the safety and security needs...

76 FR 48751 - Security Zones; Captain of the Port Lake Michigan Zone

Science.gov (United States)

2011-08-09

... Jardine Water Filtration Plant security zone would encompass all U.S. navigable waters of Lake Michigan... areas near shore to Chicago's water filtration plants; the security zones have been designed to allow.... 165.910 Security Zones; Captain of the Port Lake Michigan. (a) * * * (1) Jardine Water Filtration...

Robust model reference adaptive output feedback tracking for uncertain linear systems with actuator fault based on reinforced dead-zone modification.

Science.gov (United States)

Bagherpoor, H M; Salmasi, Farzad R

2015-07-01

In this paper, robust model reference adaptive tracking controllers are considered for Single-Input Single-Output (SISO) and Multi-Input Multi-Output (MIMO) linear systems containing modeling uncertainties, unknown additive disturbances and actuator fault. Two new lemmas are proposed for both SISO and MIMO, under which dead-zone modification rule is improved such that the tracking error for any reference signal tends to zero in such systems. In the conventional approach, adaption of the controller parameters is ceased inside the dead-zone region which results tracking error, while preserving the system stability. In the proposed scheme, control signal is reinforced with an additive term based on tracking error inside the dead-zone which results in full reference tracking. In addition, no Fault Detection and Diagnosis (FDD) unit is needed in the proposed approach. Closed loop system stability and zero tracking error are proved by considering a suitable Lyapunov functions candidate. It is shown that the proposed control approach can assure that all the signals of the close loop system are bounded in faulty conditions. Finally, validity and performance of the new schemes have been illustrated through numerical simulations of SISO and MIMO systems in the presence of actuator faults, modeling uncertainty and output disturbance. Copyright © 2015 ISA. Published by Elsevier Ltd. All rights reserved.

Enhanced stability of bound pairs at nonzero lattice momenta

International Nuclear Information System (INIS)

Kornilovitch, Pavel

2004-01-01

A two-body problem on the square lattice is analyzed. The interaction potential consists of strong on-site repulsion and nearest-neighbor attraction. The exact pairing conditions are derived for s-, p-, and d-symmetric bound states. The pairing conditions are strong functions of the total pair momentum K. It is found that the stability of pairs increases with K. At weak attraction, the pairs do not form at the Γ point but stabilize at lattice momenta close to the Brillouin zone boundary. The phase boundaries in the momentum space, which separate stable and unstable pairs, are calculated. It is found that the pairs are formed easier along the (π,0) direction than along the (π,π) direction. This might lead to the appearance of 'hot pairing spots' on the K x and K y axes

Enumeration and stability analysis of simple periodic orbits in β-Fermi Pasta Ulam lattice

International Nuclear Information System (INIS)

Sonone, Rupali L.; Jain, Sudhir R.

2014-01-01

We study the well-known one-dimensional problem of N particles with a nonlinear interaction. The special case of quadratic and quartic interaction potential among nearest neighbours is the β-Fermi-Pasta-Ulam model. We enumerate and classify the simple periodic orbits for this system and find the stability zones, employing Floquet theory. Such stability analysis is crucial to understand the transition of FPU lattice from recurrences to globally chaotic behavior, energy transport in lower dimensional system, dynamics of optical lattices and also its impact on shape parameter of bio-polymers such as DNA and RNA

Enumeration and stability analysis of simple periodic orbits in β-Fermi Pasta Ulam lattice

Energy Technology Data Exchange (ETDEWEB)

Sonone, Rupali L., E-mail: vaidehisonone@gmail.com; Jain, Sudhir R., E-mail: vaidehisonone@gmail.com [Department of Physics, University of Pune, Pune-411007, India and Nuclear Physics Division, Bhabha Atomic Research Centre, Mumbai - 400085 (India)

2014-04-24

We study the well-known one-dimensional problem of N particles with a nonlinear interaction. The special case of quadratic and quartic interaction potential among nearest neighbours is the β-Fermi-Pasta-Ulam model. We enumerate and classify the simple periodic orbits for this system and find the stability zones, employing Floquet theory. Such stability analysis is crucial to understand the transition of FPU lattice from recurrences to globally chaotic behavior, energy transport in lower dimensional system, dynamics of optical lattices and also its impact on shape parameter of bio-polymers such as DNA and RNA.

Stability analysis and backward whirl investigation of cracked rotors with time-varying stiffness

Science.gov (United States)

AL-Shudeifat, Mohammad A.

2015-07-01

The dynamic stability of dynamical systems with time-periodic stiffness is addressed here. Cracked rotor systems with time-periodic stiffness are well-known examples of such systems. Time-varying area moments of inertia at the cracked element cross-section of a cracked rotor have been used to formulate the time-periodic finite element stiffness matrix. The semi-infinite coefficient matrix obtained by applying the harmonic balance (HB) solution to the finite element (FE) equations of motion is employed here to study the dynamic stability of the system. Consequently, the sign of the determinant of a scaled version of a sub-matrix of this semi-infinite coefficient matrix at a finite number of harmonics in the HB solution is found to be sufficient for identifying the major unstable zones of the system in the parameter plane. Specifically, it is found that the negative determinant always corresponds to unstable zones in all of the systems considered. This approach is applied to a parametrically excited Mathieu's equation, a two degree-of-freedom linear time-periodic dynamical system, a cracked Jeffcott rotor and a finite element model of the cracked rotor system. Compared to the corresponding results obtained by Floquet's theory, the sign of the determinant of the scaled sub-matrix is found to be an efficient tool for identifying the major unstable zones of the linear time-periodic parametrically excited systems, especially large-scale FE systems. Moreover, it is found that the unstable zones for a FE cracked rotor with an open transverse crack model only appear at the backward whirl. The theoretical and experimental results have been found to agree well for verifying that the open crack model excites the backward whirl amplitudes at the critical backward whirling rotational speeds.

The anchoring mechanism of a bluff-body stabilized laminar premixed flame

KAUST Repository

Kedia, Kushal S.

2014-09-01

The objective of this work is to investigate the mechanism of the laminar premixed flame anchoring near a heat-conducting bluff-body. We use unsteady, fully resolved, two-dimensional simulations with detailed chemical kinetics and species transport for methane-air combustion. No artificial flame anchoring boundary conditions were imposed. Simulations show a shear-layer stabilized flame just downstream of the bluff-body, with a recirculation zone formed by the products of combustion. A steel bluff-body resulted in a slightly larger recirculation zone than a ceramic bluff-body; the size of which grew as the equivalence ratio was decreased. A significant departure from the conventional two-zone flame-structure is shown in the anchoring region. In this region, the reaction zone is associated with a large negative energy convection (directed from products to reactants) resulting in a negative flame-displacement speed. It is shown that the premixed flame anchors at an immediate downstream location near the bluff-body where favorable ignition conditions are established; a region associated with (1) a sufficiently high temperature impacted by the conjugate heat exchange between the heat-conducting bluff-body and the hot reacting flow and (2) a locally maximum stoichiometry characterized by the preferential diffusion effects. © 2014 The Combustion Institute.

Evidence of Enhanced Subrosion in a Fault Zone and Characterization of Hazard Zones with Elastic Parameters derived from SH-wave reflection Seismics and VSP

Science.gov (United States)

Wadas, S. H.; Tanner, D. C.; Tschache, S.; Polom, U.; Krawczyk, C. M.

2017-12-01

Subrosion, the dissolution of soluble rocks, e.g., sulfate, salt, or carbonate, requires unsaturated water and fluid pathways that enable the water to flow through the subsurface and generate cavities. Over time, different structures can occur that depend on, e.g., rock solubility, flow rate, and overburden type. The two main structures are sinkholes and depressions. To analyze the link between faults, groundwater flow, and soluble rocks, and to determine parameters that are useful to characterize hazard zones, several shear-wave (SH) reflection seismic profiles were surveyed in Thuringia in Germany, where Permian sulfate rocks and salt subcrop close to the surface. From the analysis of the seismic sections we conclude that areas affected by tectonic deformation phases are prone to enhanced subrosion. The deformation of fault blocks leads to the generation of a damage zone with a dense fracture network. This increases the rock permeability and thus serves as a fluid pathway for, e.g., artesian-confined groundwater. The more complex the fault geometry and the more interaction between faults, the more fractures are generated, e.g., in a strike slip-fault zone. The faults also act as barriers for horizontal groundwater flow perpendicular to the fault surfaces and as conduits for groundwater flow along the fault strike. In addition, seismic velocity anomalies and attenuation of seismic waves are observed. Low velocities high attenuation may indicate areas affected by subrosion. Other parameters that characterize the underground stability are the shear modulus and the Vp/Vs ratio. The data revealed zones of low shear modulus high Vp/Vs ratio >2.5, which probably indicate unstable areas due to subrosion. Structural analysis of S-wave seismics is a valuable tool to detect near-surface faults in order to determine whether or not an area is prone to subrosion. The recognition of even small fault blocks can help to better understand the hydrodynamic groundwater conditions

A geometric criterion for the stability of forced oscillations in non-linear mechanics (1961); Un critere geometrique de stabilite des oscillations forcees en mecanique non lineaire (1961)

Energy Technology Data Exchange (ETDEWEB)

Blaquiere, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1961-07-01

The author completes the two-parameter diagram theory which he has previously explained, by giving a geometric criterion of stability for a non-linear system under forced conditions. After two simple geometric transformations of the diagram he obtains the separators which are the boundary conditions for the zones of stability. (author) [French] L'auteur complete la theorie du diagramme a deux parametres, qu'il a anterieurement exposee, par l'enonce d'un critere geometrique de stabilite, relatif aux regimes forces d'un systeme non lineaire. Il obtient, par deux transformations geometriques simples du diagramme, les separatrices qui delimitent les zones de stabilite. (auteur)

Experimental investigation of aerodynamics, combustion, and emissions characteristics within the primary zone of a gas turbine combustor

Science.gov (United States)

Elkady, Ahmed M.

2006-04-01

The present work investigates pollutant emissions production, mainly nitric oxides and carbon monoxide, within the primary zone of a highly swirling combustion and methods with which to reduce their formation. A baseline study was executed at different equivalence ratios and different inlet air temperatures. The study was then extended to investigate the effects of utilizing transverse air jets on pollutant emission characteristics at different jet locations, jet mass ratio, and overall equivalence ratio as well as to investigate the jets' overall interactions with the recirculation zone. A Fourier Transform Infrared (FTIR) spectrometer was employed to measure emissions concentrations generated during combustion of Jet-A fuel in a swirl-cup assembly. Laser Doppler Velocimetry (LDV) was employed to investigate the mean flow aerodynamics within the combustor. Particle Image Velocimetry (PIV) was utilized to capture the instantaneous aerodynamic behavior of the non-reacting primary zone. Results illustrate that NOx production is a function of both the recirculation zone and the flame length. At low overall equivalence ratios, the recirculation zone is found to be the main producer of NOx. At near stoichiometric conditions, the post recirculation zone appears to be responsible for the majority of NOx produced. Results reveal the possibility of injecting air into the recirculation zone without altering flame stability to improve emission characteristics. Depending on the jet location and strength, nitric oxides as well as carbon monoxide can be reduced simultaneously. Placing the primary air jet just downstream of the fuel rich recirculation zone can lead to a significant reduction in both nitric oxides and carbon monoxide. In the case of fuel lean recirculation zone, reduction of nitric oxides can occur by placing the jets below the location of maximum radius of the recirculation zone.

76 FR 44803 - Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation...

Science.gov (United States)

2011-07-27

... USCG-2009-1081 New Orleans, LA Safety Zone (Part 165)..... 12/23/2009 USCG-2009-1084 Rio Vista, CA...-1096 Port Portland Zone......... Safety Zone (Part 165)..... 7/3/2010 USCG-2009-0040 La Push, WA Safety...-0950 Madisonville, LA Safety Zone (Part 165)..... 12/31/2009 USCG-2009-0951 Lower Mississippi River...

Danger Zones Dead Ahead For The U.S. And China: Prospects And Challenges

OpenAIRE

Linnea B. McCord; Terry Young; Peggy J. Crawford

2013-01-01

To be successful and remain independent, every country must create a prosperous economy, keep peace among its people, maintain political stability, and ensure the security of the people and the country from internal and external threats. Doing all four at the same time is never easy and in a time of economic volatility, change, and uncertainty juggling all four becomes more difficult. This is when countries enter the danger zone where hidden cracks and fissures in a countrys organization an...

RADIATION ACCESS ZONE AND VENTILATION CONFINEMENT ZONE CRITERIA FOR THE MGR SURFACE FACILITIES

International Nuclear Information System (INIS)

D. A. Padula

2000-01-01

The objectives of this technical report are to: (1) Establish the criteria for Radiation Access Zone (RAZ) designation. (2) Establish the criteria for the Ventilation Confinement Zone (VCZ) designation. The scope will be to formulate the RAZ and VCZ zoning designation for the Monitored Geologic Repository (MGR) surface facilities and to apply the zoning designations to the current Waste Handling Building (WHB), Waste Treatment Building (WTB), and Carrier Preparation Building (CPB) configurations

Blowoff dynamics of bluff body stabilized turbulent premixed flames

Energy Technology Data Exchange (ETDEWEB)

Chaudhuri, Swetaprovo; Kostka, Stanislav; Renfro, Michael W.; Cetegen, Baki M. [Department of Mechanical Engineering, University of Connecticut, 191 Auditorium Road, U-3139, Storrs, CT 06269 (United States)

2010-04-15

This article concerns the flame dynamics of a bluff body stabilized turbulent premixed flame as it approaches lean blowoff. Time resolved chemiluminescence imaging along with simultaneous particle image velocimetry and OH planar laser-induced fluorescence were utilized in an axisymmetric bluff body stabilized, propane-air flame to determine the sequence of events leading to blowoff and provide a quantitative analysis of the experimental results. It was found that as lean blowoff is approached by reduction of equivalence ratio, flame speed decreases and the flame shape progressively changes from a conical to a columnar shape. For a stably burning conical flame away from blowoff, the flame front envelopes the shear layer vortices. Near blowoff, the columnar flame front and shear layer vortices overlap to induce high local stretch rates that exceed the extinction stretch rates instantaneously and in the mean, resulting in local flame extinction along the shear layers. Following shear layer extinction, fresh reactants can pass through the shear layers to react within the recirculation zone with all other parts of the flame extinguished. This flame kernel within the recirculation zone may survive for a few milliseconds and can reignite the shear layers such that the entire flame is reestablished for a short period. This extinction and reignition event can happen several times before final blowoff which occurs when the flame kernel fails to reignite the shear layers and ultimately leads to total flame extinguishment. (author)

The impact of hydrogen enrichment and bluff-body lip thickness on characteristics of blended propane/hydrogen bluff-body stabilized turbulent diffusion flames

International Nuclear Information System (INIS)

Kashir, Babak; Tabejamaat, Sadegh; Jalalatian, Nafiseh

2015-01-01

Highlights: • Characteristics of C 3 H 8 –H 2 bluff-body stabilized flames are investigated. • Decreasing the bluff-body lip thickness led into enhanced flame length. • CO mass fraction is increased with reducing hydrogen content in the fuel stream. • Augmenting hydrogen content increased the maximum temperature. • Jet-like zone in propane–hydrogen bluff-body stabilized flames is very unstable. - Abstract: At the beginning of this study, the well-known turbulent bluff-body stabilized diffusion flame of HM1 is simulated by a coupled flamelet/radiation approach. The HM1 flame comprises a CH 4 :H 2 [50:50 Vol.] jet flame at a Reynolds number of 15,800. The results showed reasonable agreement for the flow field and species. Afterwards, the abovementioned approach is employed to investigate the effects of hydrogen addition on bluff-body stabilized flames of propane–hydrogen. Adding hydrogen to the blended fuel of propane/hydrogen shifts the recirculation zone outwards the bluff-body and thus culminates in increased flame length. Besides this, the flame length is predicted to be enhanced with decreasing the lip thickness of the bluff-body configuration. The CO emission level is found to be decreased with hydrogen addition in near-burner and far field regions which might be attributed to the decrease of inflow carbon atoms. The local radiative heat power reveals higher values for fuel blends with decreased contents of hydrogen at the recirculation and jet-like zones. This might be attributed to the increased local heat release rate due to breaking further carbon bonds

Ballooning stability analysis of JET H-mode discharges

International Nuclear Information System (INIS)

O'Brien, D.P.; Galvao, R.; Keilhacker, M.; Lazzaro, E.; Watkins, M.L.

1989-01-01

Previous studies of the stability of a large aspect ratio model equilibrium to ideal MHD ballooning modes have shown that across the bulk of the plasma there exist two marginally stable values of the pressure gradient parameter α. These define an unstable zone which separates the first (small α) stable region from the second (large α) stable region. Close to the separatrix, however, the first and second regions can coalesce when the surface averaged current density, Λ, exceeds a critical value. The plasma in this region is then stable to ballooning modes at all values of the pressure gradient. In this paper we extend these results to JET H-mode equilibria using a finite aspect ratio ballooning formalism, and assess the relevance of ideal ballooning stability in these discharges. In particular we analyse shot 15894 at time 56 sec. which is 1.3 s into the H-phase. (author) 4 refs., 4 figs

Subduction zone earthquake probably triggered submarine hydrocarbon seepage offshore Pakistan

Science.gov (United States)

Fischer, David; José M., Mogollón; Michael, Strasser; Thomas, Pape; Gerhard, Bohrmann; Noemi, Fekete; Volkhard, Spiess; Sabine, Kasten

2014-05-01

Seepage of methane-dominated hydrocarbons is heterogeneous in space and time, and trigger mechanisms of episodic seep events are not well constrained. It is generally found that free hydrocarbon gas entering the local gas hydrate stability field in marine sediments is sequestered in gas hydrates. In this manner, gas hydrates can act as a buffer for carbon transport from the sediment into the ocean. However, the efficiency of gas hydrate-bearing sediments for retaining hydrocarbons may be corrupted: Hypothesized mechanisms include critical gas/fluid pressures beneath gas hydrate-bearing sediments, implying that these are susceptible to mechanical failure and subsequent gas release. Although gas hydrates often occur in seismically active regions, e.g., subduction zones, the role of earthquakes as potential triggers of hydrocarbon transport through gas hydrate-bearing sediments has hardly been explored. Based on a recent publication (Fischer et al., 2013), we present geochemical and transport/reaction-modelling data suggesting a substantial increase in upward gas flux and hydrocarbon emission into the water column following a major earthquake that occurred near the study sites in 1945. Calculating the formation time of authigenic barite enrichments identified in two sediment cores obtained from an anticlinal structure called "Nascent Ridge", we find they formed 38-91 years before sampling, which corresponds well to the time elapsed since the earthquake (62 years). Furthermore, applying a numerical model, we show that the local sulfate/methane transition zone shifted upward by several meters due to the increased methane flux and simulated sulfate profiles very closely match measured ones in a comparable time frame of 50-70 years. We thus propose a causal relation between the earthquake and the amplified gas flux and present reflection seismic data supporting our hypothesis that co-seismic ground shaking induced mechanical fracturing of gas hydrate-bearing sediments

Influence of lithological characters of coal bearing formation on stability of roof of coal seams

Energy Technology Data Exchange (ETDEWEB)

Meng Zhao-ping; Peng Su-ping; Li Guo-qing; Huang Wei; Lu Jun; Lei Zhi-yong [CUMT, Beijing (China). School of Resources and Safety Engineering

2003-07-01

Lithology is one of the important factors influencing the stability of roof of coal seams. In order to investigate this, the phenomenon of underground pressure and distribution of pressure were studied by using the local observation and simulation test with similar materials. The observation results show that the distance of initial weighting and periodic weighting of the mudstone roof is shorter than that of sandstone roofs. The sandstone roof with a high strength has a longer distance of initial weighting and periodic weighting, the abutment stress on the working face is big and the height of caving and fracture zone is high. The peak point of abutment stress in the sandstone roof is near to the working face and the pressure bump is inclined to occur. The result is contrary to that in case of the mudstone roof with a low strength. While in the transition zone of nipped sandstone, roof rock-mass is broken and is poor in stability, therefore, it is difficult to hold the roof.

Dynamic stability and bifurcation analysis in fractional thermodynamics

Science.gov (United States)

Béda, Péter B.

2018-02-01

In mechanics, viscoelasticity was the first field of applications in studying geomaterials. Further possibilities arise in spatial non-locality. Non-local materials were already studied in the 1960s by several authors as a part of continuum mechanics and are still in focus of interest because of the rising importance of materials with internal micro- and nano-structure. When material instability gained more interest, non-local behavior appeared in a different aspect. The problem was concerned to numerical analysis, because then instability zones exhibited singular properties for local constitutive equations. In dynamic stability analysis, mathematical aspects of non-locality were studied by using the theory of dynamic systems. There the basic set of equations describing the behavior of continua was transformed to an abstract dynamic system consisting of differential operators acting on the perturbation field variables. Such functions should satisfy homogeneous boundary conditions and act as indicators of stability of a selected state of the body under consideration. Dynamic systems approach results in conditions for cases, when the differential operators have critical eigenvalues of zero real parts (dynamic stability or instability conditions). When the critical eigenvalues have non-trivial eigenspace, the way of loss of stability is classified as a typical (or generic) bifurcation. Our experiences show that material non-locality and the generic nature of bifurcation at instability are connected, and the basic functions of the non-trivial eigenspace can be used to determine internal length quantities of non-local mechanics. Fractional calculus is already successfully used in thermo-elasticity. In the paper, non-locality is introduced via fractional strain into the constitutive relations of various conventional types. Then, by defining dynamic systems, stability and bifurcation are studied for states of thermo-mechanical solids. Stability conditions and genericity

Flame macrostructures, combustion instability and extinction strain scaling in swirl-stabilized premixed CH4/H2 combustion

KAUST Repository

Shanbhogue, S.J.

2016-01-01

© 2015 The Combustion Institute. In this paper, we report results from an experimental investigation on transitions in the average flame shape (or microstructure) under acoustically coupled and uncoupled conditions in a 50 kW swirl stabilized combustor. The combustor burns CH4/H2 mixtures at atmospheric pressure and temperature for a fixed Reynolds number of 20,000 and fixed swirl angle. For both cases, essentially four different flame shapes are observed, with the transition between flame shapes occurring at the same equivalence ratio (for the same fuel mixture) irrespective of whether the combustor is acoustically coupled or uncoupled. The transition equivalence ratio depends on the fuel mixture. For the baseline case of pure methane, the combustor is stable close to the blowoff limit and the average flame in this case is stabilized inside the inner recirculation zone. As the equivalence ratio is raised, the combustor transitions to periodic oscillations at a critical equivalence ratio of φ=0.65. If hydrogen is added to the mixture, the same transition occurs at lower equivalence ratios. For all cases that we investigated, flame shapes captured using chemiluminescence imaging show that the transition to harmonic oscillations in the acoustically coupled cases is preceded by the appearance of the flame in the outer recirculation zone. We examine the mechanism associated with the transition of the flame between different shapes and, ultimately, the propagation of the flame into the outer recirculation zone as the equivalence ratio is raised. Using the extinction strain rates for each mixture at different equivalence ratios, we show that these transitions in the flame shape and in the instability (in the coupled case) for different fuel mixtures collapse as a function of a normalized strain rate : κextDU∞. We show that the results as consistent with a mechanism in which the flame must overcome higher strains prevailing in the outer recirculation zone, in order

33 CFR 165.1315 - Safety Zones: Fireworks displays in the Captain of the Port Portland Zone.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety Zones: Fireworks displays... Coast Guard District § 165.1315 Safety Zones: Fireworks displays in the Captain of the Port Portland Zone. (a) Safety zones. The following areas are designated safety zones: (1) Cinco de Mayo Fireworks...

The working zone in the interpolar area of the Faraday balance: an approach to testing the magnetic force factor stability criterion

Directory of Open Access Journals (Sweden)

Sandulyak Alexander V.

2017-01-01

Full Text Available Due to rapid development of the scientific and applied research in magnetic control and magnetophoresis of ferro- and ferromagnetic disperse fraction of various technological, natural and industry-specific media, the Faraday method is again in high demand as it is mainly aimed at defining magnetic susceptibility of solid and heterogeneous samples of small volumes. Based on the appearing (and then measured ponderomotive force impacting the sample, the method allows accurate determining of single particles magnetic susceptibility by using the data of the sample represented by a conglomerate of the particles of such a fraction. In addition, it is mentioned that to date there is still a great gap in the methodology of the Faraday method as there are no exact recommendations on choosing both the form of the polar pieces of the Faraday balance and the positioning of the sample (the location of the working zone in the interpolar area. Owing to these drawbacks, the well-known and long-time used Faraday method cannot be considered substantiated to a satisfactory degree. Thus, in our point of view, the treatment of the results obtained earlier with the help of the method should be cautious. In our work, we experimentally defined and substantiated an approach to identifying a working (local zone, viz. the zone with stable values of the magnetic force factor – the product of the field intensity and induction by its gradient. The approach features the relative phenomenological analysis and is exemplified by polar pieces of non-traditional spherical form. It has been demonstrated that in order to state the fact of mere existence of this zone (and its location in the interpolar area, the coordinate (usually nonlinear one characteristic of intensity or induction, which is obligatorily obtained in an experiment, should have an inflexion, which guarantees a functionally extreme view of the following coordinate characteristics both of the gradient and that of

77 FR 30245 - Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone

Science.gov (United States)

2012-05-22

...'' N, 082-51'-18.70'' W (NAD 83). This proposed zone would be enforced one evening during the last week...-AA00 Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone AGENCY: Coast Guard... by adding three permanent safety zones within the Captain of the Port Detroit Zone. This action is...

Assessment of Slope Stability of Various Cut Slopes with Effects of Weathering by Using Slope Stability Probability Classification (SSPC)

Science.gov (United States)

Ersöz, Timur; Topal, Tamer

2017-04-01

Rocks containing pore spaces, fractures, joints, bedding planes and faults are prone to weathering due to temperature differences, wetting-drying, chemistry of solutions absorbed, and other physical and chemical agents. Especially cut slopes are very sensitive to weathering activities because of disturbed rock mass and topographical condition by excavation. During and right after an excavation process of a cut slope, weathering and erosion may act on this newly exposed rock material. These acting on the material may degrade and change its properties and the stability of the cut slope in its engineering lifetime. In this study, the effect of physical and chemical weathering agents on shear strength parameters of the rocks are investigated in order to observe the differences between weathered and unweathered rocks. Also, slope stability assessment of cut slopes affected by these weathering agents which may disturb the parameters like strength, cohesion, internal friction angle, unit weight, water absorption and porosity are studied. In order to compare the condition of the rock materials and analyze the slope stability, the parameters of weathered and fresh rock materials are found with in-situ tests such as Schmidt hammer and laboratory tests like uniaxial compressive strength, point load and direct shear. Moreover, slake durability and methylene blue tests are applied to investigate the response of the rock to weathering and presence of clays in rock materials, respectively. In addition to these studies, both rock strength parameters and any kind of failure mechanism are determined by probabilistic approach with the help of SSPC system. With these observations, the performances of the weathered and fresh zones of the cut slopes are evaluated and 2-D slope stability analysis are modeled with further recommendations for the cut slopes. Keywords: 2-D Modeling, Rock Strength, Slope Stability, SSPC, Weathering

Formulation design for target delivery of iron nanoparticles to TCE zones.

Science.gov (United States)

Wang, Ziheng; Acosta, Edgar

2013-12-01

Nanoparticles of zero-valent iron (NZVI) are effective reducing agents for some dense non-aqueous phase liquid (DNAPL) contaminants such as trichloroethylene (TCE). However, target delivery of iron nanoparticles to DNAPL zones in the aquifer remains an elusive feature for NZVI technologies. This work discusses three strategies to deliver iron nanoparticles to DNAPL zones. To this end, iron oxide nanoparticles coated with oleate (OL) ions were used as stable analogs for NZVI. The OL-coated iron oxide nanoparticles are rendered lipophilic via (a) the addition of CaCl2, (b) acidification, or (c) the addition of a cationic surfactant, benzethonium chloride (BC). Mixtures of OL and BC show promise as a target delivery strategy due to the high stability of the nanoparticles in water, and their preferential partition into TCE in batch experiments. Column tests show that while the OL-BC coated iron oxide nanoparticles remain largely mobile in TCE-free columns, a large fraction of these particles are retained in TCE-contaminated columns, confirming the effectiveness of this target delivery strategy. © 2013.

33 CFR 165.503 - Security Zone; Captain of the Port Hampton Roads Zone.

Science.gov (United States)

2010-07-01

... Port Hampton Roads Zone. 165.503 Section 165.503 Navigation and Navigable Waters COAST GUARD... § 165.503 Security Zone; Captain of the Port Hampton Roads Zone. (a) Definitions. As used in this... been authorized by the Captain of the Port (COTP), Hampton Roads, Virginia to act on his or her behalf...

Foam-Delivery of Remedial Amendments for Enhanced Vadose Zone Metals and Radionuclides Remediation

International Nuclear Information System (INIS)

Zhong, L.; Szecsody, J.E.; Dresel, P.E.; Zhang, Z.F.; Qafoku, N.P.

2009-01-01

The remediation of metals and radionuclides contamination, such as Cr(VI), Tc-99, and Sr-90 in the U.S. DOE Hanford Site vadose zone is a critical need. Water-based remedial amendments delivery to the deep vadose zone is facing significant technical challenges. Water-based delivery will easily leach out the highly mobile pollutants therefore contaminate the underlying aquifer. Preferential flow of the amendment-laden solution in the vadose zone due to the formation heterogeneity is difficult to overcome, resulting in bypassing of the less permeable zones. Foam has unique transport properties in the vadose zone that enable mitigation on the mobilization of mobile contaminants and enhance the sweeping over heterogeneous systems. Calcium polysulfide (CPS) is a remedial amendment that can be used to reduce and immobilize hexavalent chromium [Cr(VI)] and other redox-sensitive radionuclides/metals in the vadose zone. The delivery of CPS to the vadose zone using foam and the immobilization of Cr(VI) via reduction by the foam-delivered CPS was investigated in this study. Batch tests were conducted to select the foam-generating CPS-surfactant solutions, to determine the solution foamability and the reducing potential of CPS-containing foams, and to study the influence of foam quality, surfactant concentration, and CPS concentration on foam stability. Column experiments were performed to test the foam delivery of CPS to sediments under conditions similar to field vadose zone, to study the foam transport and interaction with sediments, and to determine the extent of Cr(VI) immobilization using this novel delivery approach. CPS-containing foams with high reducing potential were prepared based on the batch tests. Sediment reduction by foam-delivered CPS was observed in the column studies. Significant mobilization of Cr(VI) from sediments occurred when CPS was delivered in aqueous solution. The Cr(VI) mobilization was minimized when CPS was delivered by foams, resulting in

Impact of Vitiation on a Swirl-Stabilized and Premixed Methane Flame

Directory of Open Access Journals (Sweden)

Mao Li

2017-10-01

Full Text Available Vitiation refers to the condition where the oxygen concentration in the air is reduced due to the mix of dilution gas. The vitiation effects on a premixed methane flame were investigated on a swirl-stabilized gas turbine model combustor under atmospheric pressure. The main purpose is to analyze the combustion stability and CO emission performance in vitiated air and compare the results with the flame without vitiation. The N2, CO2, and H2O (steam were used as the dilution gas. Measurements were conducted in a combustor inlet temperature of 384 K and 484 K. The equivalence ratio was varied from stoichiometric conditions to the LBO (Lean Blowout limits where the flame was physically blown out from the combustor. The chemical kinetics calculation was performed with Chemkin software to analyze the vitiation effects on the flame reaction zone. Based on the calculation results, the changes in the temperature gradient, CO concentration, and active radicals across the flame reaction zone were identified. The time-averaged CH chemiluminescence images were recorded and the results indicated the features of the flame shape and location. The CH signal intensity provided the information about the heat-release zone in the combustor. The combustion LBO limits were measured and the vitiation of CO2 and H2O were found to have a stronger impact to elevate the LBO limits than N2. Near the LBO limits, the instability of the flame reaction was revealed by the high-speed chemiluminescence imaging and the results were analyzed by FFT (Fast Fourier Transfer. CO emission was measured with a water-cooled probe which is located at the exit of the combustor. The combustion vitiation has been found to have the compression effect on the operation range for low CO emission. However, this compression effect could be compensated by improving the combustor inlet temperature.

Stability considerations and a double-diffusive convection model for solar ponds

Energy Technology Data Exchange (ETDEWEB)

Lin, E.I.H.; Sha, W.T.; Soo, S.L.

1979-04-01

A brief survey is made on the basic principles, current designs and economic advantages of salinity-gradient solar ponds as solar collectors and reservoirs. Solar ponds are well-suited for various AIPH (agricultural and industrial process heat) applications, and as annual storage devices for space heating and cooling. The benefit of an efficient pond is demonstrated via a preliminary economic analysis which suggests the idea of energy farming as a profitable alternative for land usage in the face of rising fuel cost. The economy and reliability of solar-pond operation depend crucially on the stability of the nonconvective gradient zone against disturbances such as generated by a severe weather condition. Attention is focused on the subject of stability, and pertinent existing results are summarized and discussed. Details of the derivation of three-dimensional stability criteria for thermohaline convection with linear gradients are presented. Ten key questions pertaining to stability are posed, whose answers must be sought through extensive analytical and numerical studies. Possible methods of approach toward enhancing solar-pond stability are also discussed. For the numerical studies of pond behavior and stability characteristics, a double-diffusive convection model is proposed. The model can be constructed by extending the three-dimensional thermohydrodynamic computer code COMMIX-SA, following the necessary steps outlined; computational plans are described. Similarities exist between the halothermocline and the thermocline storage systems, and an extended COMMIX-SA will be a valuable tool for the investigation of both.

Formulating a coastal zone health metric for landuse impact management in urban coastal zones.

Science.gov (United States)

Anilkumar, P P; Varghese, Koshy; Ganesh, L S

2010-11-01

The need for ICZM arises often due to inadequate or inappropriate landuse planning practices and policies, especially in urban coastal zones which are more complex due to the larger number of components, their critical dimensions, attributes and interactions. A survey of literature shows that there is no holistic metric for assessing the impacts of landuse planning on the health of a coastal zone. Thus there is a need to define such a metric. The proposed metric, CHI (Coastal zone Health Indicator), developed on the basis of coastal system sustainability, attempts to gauge the health status of any coastal zone. It is formulated and modeled through an expert survey and pertains to the characteristic components of coastal zones, their critical dimensions, and relevant attributes. The proposed metric is applied to two urban coastal zones and validated. It can be used for more coast friendly and sustainable landuse planning/masterplan preparation and thereby for the better management of landuse impacts on coastal zones. Copyright 2010 Elsevier Ltd. All rights reserved.

Vertical and horizontal extension of the oxygen minimum zone in the eastern South Pacific Ocean

Science.gov (United States)

Fuenzalida, Rosalino; Schneider, Wolfgang; Garcés-Vargas, José; Bravo, Luis; Lange, Carina

2009-07-01

Recent hydrographic measurements within the eastern South Pacific (1999-2001) were combined with vertically high-resolution data from the World Ocean Circulation Experiment, high-resolution profiles and bottle casts from the World Ocean Database 2001, and the World Ocean Atlas 2001 in order to evaluate the vertical and horizontal extension of the oxygen minimum zone (oxygen minimum zone to be 9.82±3.60×10 6 km 2 and 2.18±0.66×10 6 km 3, respectively. The oxygen minimum zone is thickest (>600 m) off Peru between 5 and 13°S and to about 1000 km offshore. Its upper boundary is shallowest (zone in some places. Offshore, the thickness and meridional extent of the oxygen minimum zone decrease until it finally vanishes at 140°W between 2° and 8°S. Moving southward along the coast of South America, the zonal extension of the oxygen minimum zone gradually diminishes from 3000 km (15°S) to 1200 km (20°S) and then to 25 km (30°S); only a thin band is detected at ˜37°S off Concepción, Chile. Simultaneously, the oxygen minimum zone's maximum thickness decreases from 300 m (20°S) to less than 50 m (south of 30°S). The spatial distribution of Ekman suction velocity and oxygen minimum zone thickness correlate well, especially in the core. Off Chile, the eastern South Pacific Intermediate Water mass introduces increased vertical stability into the upper water column, complicating ventilation of the oxygen minimum zone from above. In addition, oxygen-enriched Antarctic Intermediate Water clashes with the oxygen minimum zone at around 30°S, causing a pronounced sub-surface oxygen front. The new estimates of vertical and horizontal oxygen minimum zone distribution in the eastern South Pacific complement the global quantification of naturally hypoxic continental margins by Helly and Levin [2004. Global distribution of naturally occurring marine hypoxia on continental margins. Deep-Sea Research I 51, 1159-1168] and provide new baseline data useful for studies on the

Thermal treatment system of hazardous residuals in three heating zones based on a microprocessor

International Nuclear Information System (INIS)

Luna H, C.L.

1997-01-01

Thermal treatment system consists of a high power electric oven of three heating zones where each zone works up to 1200 Centigrades; it has the capacity of rising the central zone temperature up to 1000 Centigrades in 58 minutes approximately. This configuration of three zones could be programmed to different temperatures and they will be digitally controlled by a control microprocessor, which has been controlled by its own assembler language, in function of the PID control. There are also other important controls based on this microprocessor, as a signal amplification, starting and shutdown of high power step relays, activation and deactivation of both analogic/digital and digital/analogic convertors, port activation and basic data storage of the system. Two main characteristics were looked for this oven design; the first was the possibility of controlling the three zone temperature and the second was to reduce the rising and stabilization operation time and its digitized control. The principal function of the three zone oven is to accelerate the degradation of hazardous residuals by an oxidation instead combustion, through relatively high temperatures (minimum 800 Centigrades and maximum 1200 Centigrades); this process reduces the ash and volatile particulate production. The hazardous residuals will be pumped into the degradation system and after atomized through a packaged column; this step will avoid the direct contact of the residuals with the oven cores. These features make this system as closed process, which means that the residuals can not leak to the working area, reducing the exposure risk to the personnel. This three step oven system is the first stage of the complete hazardous residuals degradation system; after this, the flow will go into a cold plasma region where the process is completed, making a closed system. (Author)

77 FR 6007 - Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation...

Science.gov (United States)

2012-02-07

...] Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation... they could be published in the Federal Register. This notice lists temporary safety zones, security... the safety and security needs within their jurisdiction; therefore, District Commanders and COTPs have...

A Two-Dimensional Numerical Study of Hydrodynamic, Heat and Mass Transfer and Stability in a Salt Gradient Solar Pond

Directory of Open Access Journals (Sweden)

Ali Ben Moussa

2012-10-01

Full Text Available In this work, the problem of hydrodynamic, heat and mass transfer and stability in a salt gradient solar pond has been numerically studied by means of computational fluid dynamics in transient regime. The body of the simulated pond is an enclosure of height H and length L wherein an artificial salinity gradient is created in order to suppress convective motions induced by solar radiation absorption and to stabilize the solar pond during the period of operation. Here we show the distribution of velocity, temperature and salt concentration fields during energy collection and storage in a solar pond filled with water and constituted by three different salinity zones. The bottom of the pond is blackened and the free-surface is subjected to heat losses by convection, evaporation and radiation while the vertical walls are adiabatic and impermeable. The governing equations of continuity, momentum, thermal energy and mass transfer are discretized by finite–volume method in transient regime. Velocity vector fields show the presence of thin convective cells in the upper convective zone (UCZ and large convective cells in the lower convective zone (LCZ. This study shows the importance of buoyancy ratio in the decrease of temperature in the UCZ and in the preservation of high temperature in the LCZ. It shows also the importance of the thickness of Non-Convective Zone (NCZ in the reduction of the upwards heat losses.

78 FR 26508 - Safety Zone; Fireworks Event in Captain of the Port New York Zone

Science.gov (United States)

2013-05-07

... Harbor located in approximate Safety Zone, 33 CFR 165.160(3.8). position 40[deg]51'58'' N, 073[deg]39'34... Zone; Fireworks Event in Captain of the Port New York Zone AGENCY: Coast Guard, DHS. ACTION: Notice of enforcement of regulation. SUMMARY: The Coast Guard will enforce safety zones in the Captain of the Port New...

The distinguishing characteristics of interlayer oxidation zone and burial ancient ground oxidation zone

International Nuclear Information System (INIS)

Zhang Zhanshi; Zhou Wenbin

1998-01-01

The author discusses the main characteristics of interlayer oxidation zones and the burial ancient ground oxidation zones of Uranium deposit No. 512 in Xinjiang Uigur municipality. The epigenetic genesis, depending on some aquifer, the tongue-like in section, having the zonation along dip direction and having certain mineral assemblage are the typical features for interlayer oxidation zones

Zoning Districts - Volusia County HUB Zones

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Historically Underutilized Business (HUB) Zones in Volusia County. Go to http://www.sba.gov/hubzone or contact the Department of Economic Development (386) 248-8048...

VT Data - Zoning 20120709, Huntington

Data.gov (United States)

Vermont Center for Geographic Information — Zoning district data for the Town of Huntington, Vermont. For details regarding each zoning district refer to the current zoning regulations on town of Huntington's...

Single crystal growth of 67%BiFeO3-33%BaTiO3 solution by the floating zone method

Science.gov (United States)

Rong, Y.; Zheng, H.; Krogstad, M. J.; Mitchell, J. F.; Phelan, D.

2018-01-01

The growth conditions and the resultant grain morphologies and phase purities from floating-zone growth of 67%BiFeO3-33%BaTiO3 (BF-33BT) single crystals are reported. We find two formidable challenges for the growth. First, a low-melting point constituent leads to a pre-melt zone in the feed-rod that adversely affects growth stability. Second, constitutional super-cooling (CSC), which was found to lead to dendritic and columnar features in the grain morphology, necessitates slow traveling rates during growth. Both challenges were addressed by modifications to the floating-zone furnace that steepened the temperature gradient at the melt-solid interfaces. Slow growth was also required to counter the effects of CSC. Single crystals with typical dimensions of hundreds of microns have been obtained which possess high quality and are suitable for detailed structural studies.

Single crystal growth of 67%BiFeO 3 -33%BaTiO 3 solution by the floating zone method

Energy Technology Data Exchange (ETDEWEB)

Rong, Y.; Zheng, H.; Krogstad, M. J.; Mitchell, J. F.; Phelan, D.

2018-01-01

The growth conditions and the resultant grain morphologies and phase purities from floating-zone growth of 67%BiFeO3-33%BaTiO3 (BF-33BT) single crystals are reported. We find two formidable challenges for the growth. First, a low-melting point constituent leads to a pre-melt zone in the feed-rod that adversely affects growth stability. Second, constitutional super-cooling (CSC), which was found to lead to dendritic and columnar features in the grain morphology, necessitates slow traveling rates during growth. Both challenges were addressed by modifications to the floating-zone furnace that steepened the temperature gradient at the melt-solid interfaces. Slow growth was also required to counter the effects of CSC. Single crystals with typical dimensions of hundreds of microns have been obtained which possess high quality and are suitable for detailed structural studies.

Evaluation of long-term mechanical stability of near field

International Nuclear Information System (INIS)

Takaji, Kazuhiko; Sugino, Hiroyuki; Okutsu, Kazuo; Miura, Kazuhiko; Tabei, Kazuto; Noda, Masaru; Takahashi, Shinichi; Sugie, Shigehiko

1999-11-01

In the near field, as tunnels and pits are excavated, a redistribution of stresses in the surrounding rock will occur. For a long period of time after the emplacement of waste packages various events will take place, such as the swelling of the buffer, sinking of the overpack under its own weight, deformation arising from expansion of overpack corrosion products and the creep deformation of the rock mass. The evaluation of what effects these changes in the stress-state will have on the buffer and rock mass is a major issue from the viewpoint of safety assessment. Therefore, rock creep analysis, overpack corrosion expansion analysis and overpack sinking analysis have been made in order to examine the long-term mechanical stability of the near field and the interaction of various events that may affect the stability of the near field over a long period of time. As the results, rock creep behavior, the variations of the stress-state and the range of the influence zone differ from the rock strength, strength of buffer in the tunnel and side pressure coefficient etc. about the hard rock system and soft rock system established as basic cases. And the magnitude of the stress variations for buffer by the overpack sinking and rock creep deformation is negligible compared with it by the overpack corrosion expansion. Furthermore, though very limited zone of buffer around the overpack is close to the critical state by the overpack corrosion expansion, the engineered barrier system attains a comparatively stable state for a long period of time. (author)

In situ quantification of ultra-low O2 concentrations in oxygen minimum zones

DEFF Research Database (Denmark)

Larsen, Morten; Lehner, Philipp; Borisov, Sergey M.

2016-01-01

based on the palladium(II)-benzoporphyrin luminophore, immobilized in a perfluorinated matrix with high O2 permeability. The trace sensor has a detection limit of ∼5 nmol L−1 with a dynamic range extending up to ∼2 μmol L−1. The sensor demonstrates a response time ..., and fully reversible response to hydrostatic pressure and temperature. The sensor showed excellent stability for continuously measurements during depth profiling in Oxygen Minimum Zones (OMZ). The novel sensor was deployed in situ using a Trace Oxygen Profiler instrument (TOP) equipped with two additional O...

Improving the calculated core stability by the core nuclear design optimization

International Nuclear Information System (INIS)

Partanen, P.

1995-01-01

Three different equilibrium core loadings for TVO II reactor have been generated in order to improve the core stability properties at uprated power level. The reactor thermal power is assumed to be uprated from 2160 MW th to 2500 MW th , which moves the operating point after a rapid pump rundown where the core stability has been calculated from 1340 MW th and 3200 kg/s to 1675 MW th and 4000 kg/s. The core has been refuelled with ABB Atom Svea-100 -fuel, which has 3,64% w/o U-235 average enrichment in the highly enriched zone. PHOENIX lattice code has been used to provide the homogenized nuclear constants. POLCA4 static core simulator has been used for core loadings and cycle simulations and RAMONA-3B program for simulating the dynamic response to the disturbance for which the stability behaviour has been evaluated. The core decay ratio has been successfully reduced from 0,83 to 0,55 mainly by reducing the power peaking factors. (orig.) (7 figs., 1 tab.)

33 CFR 147.847 - Safety Zone; BW PIONEER Floating Production, Storage, and Offloading System Safety Zone.

Science.gov (United States)

2010-07-01

... Production, Storage, and Offloading System Safety Zone. 147.847 Section 147.847 Navigation and Navigable... ZONES § 147.847 Safety Zone; BW PIONEER Floating Production, Storage, and Offloading System Safety Zone. (a) Description. The BW PIONEER, a Floating Production, Storage and Offloading (FPSO) system, is in...

Thermal stability and haemolytic effects of depolymerized guar gum derivatives.

Science.gov (United States)

Hussain, Majid; Zahoor, Tahir; Akhtar, Saeed; Ismail, Amir; Hameed, Aneela

2018-03-01

The purpose of current study was to purify and partially depolymerize guar gum by β-mannanase, HCl, Ba(OH) 2 actions and subjected to inspect compositional, thermogravimetric analysis (TGA) and haemolytic activity. Chemical composition revealed mannose and galactose ratio remained un-altered even after process of purification and hydrolysis. TGA thermograms affirmed initial and final decomposition temperature in various zones. Major decomposition stages apparently revealed partially hydrolyzed guar gum (PHGG) exhibited better heat stable properties having more zones of degradation than crude one. Furthermore, all guar fractions (2.5-250 mg/mL) were subjected to haemolysis to evaluate toxic effects during process of hydrolysis. The crude and hydrolyzed guar galactomannans exhibited minor haemolytic activity (1.9 ± 0.03-7.24 ± 0.02%) when compared to 0.1% Triton-X 100 (100% haemolysis) showing no toxic effects to human RBC's. Conclusively, hydrolyzed guar-galactomannans are safe and can be used in food products with improved heat stability.

Vadose zone process that control landslide initiation and debris flow propagation

Science.gov (United States)

Sidle, Roy C.

2015-04-01

Advances in the areas of geotechnical engineering, hydrology, mineralogy, geomorphology, geology, and biology have individually advanced our understanding of factors affecting slope stability; however, the interactions among these processes and attributes as they affect the initiation and propagation of landslides and debris flows are not well understood. Here the importance of interactive vadose zone processes is emphasized related to the mechanisms, initiation, mode, and timing of rainfall-initiated landslides that are triggered by positive pore water accretion, loss of soil suction and increase in overburden weight, and long-term cumulative rain water infiltration. Both large- and small-scale preferential flow pathways can both contribute to and mitigate instability, by respectively concentrating and dispersing subsurface flow. These mechanisms are influenced by soil structure, lithology, landforms, and biota. Conditions conducive to landslide initiation by infiltration versus exfiltration are discussed relative to bedrock structure and joints. The effects of rhizosphere processes on slope stability are examined, including root reinforcement of soil mantles, evapotranspiration, and how root structures affect preferential flow paths. At a larger scale, the nexus between hillslope landslides and in-channel debris flows is examined with emphasis on understanding the timing of debris flows relative to chronic and episodic infilling processes, as well as the episodic nature of large rainfall and related stormflow generation in headwater streams. The hydrogeomorphic processes and conditions that determine whether or not landslides immediately mobilize into debris flows is important for predicting the timing and extent of devastating debris flow runout in steep terrain. Given the spatial footprint of individual landslides, it is necessary to assess vadose zone processes at appropriate scales to ascertain impacts on mass wasting phenomena. Articulating the appropriate

The effect of the height of the extraction solution zone on the effectiveness of phenol purification of oils

Energy Technology Data Exchange (ETDEWEB)

Shwetsov, A M; Petrov, V N; Plaksina, R V

1982-01-01

Studies are conducted in order to investigate the effect of the location of the interface level on the quality and output of a refinate (Rf) during phenol purification of oils in an industrial installation. During purification of deasphaltizate from a mixture of Romashkinsk and Tuymazinsk oils the height of the solution extraction (ER) zone was altered, while the solution extracted from the lower part of the column was sent to a tank settler for separating the second refinate phase (VRF) from it. In order to observe the position of the interface between the second refinate phase and the extraction solution, the tank was equipped with electrodes. It is shown that with an extraction solution zone height of 5.5 meters, intensive isolation of the second refinate phase in the tank is observed; here, the quality and output of the refinate are low. An increase in the extraction solution zone to 9.5 meters improves the quality of the refinate, but its output remains low. With an increase in the extraction solution zone height to 12.3 meters, the operation of the column is stabilized.

78 FR 5717 - Safety Zone; Military Ocean Terminal Concord Safety Zone, Suisun Bay, Military Ocean Terminal...

Science.gov (United States)

2013-01-28

...-AA00 Safety Zone; Military Ocean Terminal Concord Safety Zone, Suisun Bay, Military Ocean Terminal... Guard is establishing a safety zone in the navigable waters of Suisun Bay near Military Ocean Terminal Concord, CA in support of military onload and offload operations. This safety zone is established to...

Possible gas hydrates on the Bjarmeland Platform; seismic expression and stability modelling

OpenAIRE

Løvaas, John Sverre

2016-01-01

Seismic evidence of shallow gas anomalies are prominent at Ververis Dome structure and Hoop Fault Complex in Bjarmeland Platform. Ubiquitous high amplitude anomalies at the same depth as these shallow gas anomalies infer a possible relation to gas hydrates. A wide range of fluid flow structures within the two study areas have previously been discovered and reported, and may possibly feed the base of the gas hydrate stability zone (BGHSZ) with upward migrating thermogenic gas. This thesis f...

Corrosion Behavior of Heat Affected Zone of AISI 321 stainless steel

International Nuclear Information System (INIS)

Ahn, Yong Sik; Park, Hwa Soon; Kim, Yeong Hwan; Won, Tae Yeon; Lee, Sang Lae

1994-01-01

Intergranular corrosion behavior of heat affected zone(HAZ) has been investigated for Ti-stabilized austenitic stainless steel AISI 321. It was observed that grain boundaries at HAZ of the steel with Ti/C ratio of 6.2 were corroded significantly after sensitization heat treatment. The increase of the Ti/C ratio up to 9.6 results in the evident decrease of intergranular corrosion. Weld simulation and intergranular corrosion test in 65% HNO 3 was performed. Influence of various thermal cycles on the intergranular corrosion was investigated. These results are discussed in terms of the behavior of TiC and Cr 23 C 6 precipitates

Manipulation of recombination zone by utilizing the donor of electroplex as a spacer

Energy Technology Data Exchange (ETDEWEB)

Lü, Zhaoyue, E-mail: lvzhaoyue@ecust.edu.cn [Department of Physics, School of Science, East China University of Science & Technology, Shanghai 200237 (China); Yin, Yuehong [Department of Applied Physics, Institute of Physical Chemistry, Henan Polytechnic University, Jiaozuo, Henan Province 454000 (China); Xiao, Jing [Physics and Electronic Engineering College, Taishan University, Shandong Province 271021,China (China)

2016-11-15

The emission of electroplex is varied with applied voltages, leading to poor color stability of devices. In this work, the recombination region was investigated in organic light-emitting diodes (OLEDs) based on the electroplex between N,N’-diphenyl-N,N’-bis(1-naphthyl-phenyl)-1,1′-biphenyl-4,4′-diamine(NPB) and 2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,2,4-oxadiazole (PBD). Color stability was manipulated by introducing the donor of electroplex as a spacer, which plays an important role of recombination zone for electroplex-based OLEDs. The 5-nm-spacer-device brought out a tolerable chromaticity coordinate shift of less than 0.01 for both x- and y-value. White light emission with CIE coordinates of (0.37,0.28) and (0.33,0.26) at 12 V was achieved when the thickness of spacer was 7 and 10 nm, respectively. The 7-nm-spacer-device exhibited better color stability than the 10-nm-spacer-device. This proves that adjusting spacer thickness is a simple and efficient method to control recombination region and can be useful for fulfilling color-stable electroplex-based white emission.

Manipulation of recombination zone by utilizing the donor of electroplex as a spacer

International Nuclear Information System (INIS)

Lü, Zhaoyue; Yin, Yuehong; Xiao, Jing

2016-01-01

The emission of electroplex is varied with applied voltages, leading to poor color stability of devices. In this work, the recombination region was investigated in organic light-emitting diodes (OLEDs) based on the electroplex between N,N’-diphenyl-N,N’-bis(1-naphthyl-phenyl)-1,1′-biphenyl-4,4′-diamine(NPB) and 2-(4-biphenylyl)-5-(4-tert-butylphenyl)-1,2,4-oxadiazole (PBD). Color stability was manipulated by introducing the donor of electroplex as a spacer, which plays an important role of recombination zone for electroplex-based OLEDs. The 5-nm-spacer-device brought out a tolerable chromaticity coordinate shift of less than 0.01 for both x- and y-value. White light emission with CIE coordinates of (0.37,0.28) and (0.33,0.26) at 12 V was achieved when the thickness of spacer was 7 and 10 nm, respectively. The 7-nm-spacer-device exhibited better color stability than the 10-nm-spacer-device. This proves that adjusting spacer thickness is a simple and efficient method to control recombination region and can be useful for fulfilling color-stable electroplex-based white emission.

78 FR 24679 - Safety Zones; Fireworks Displays in Captain of the Port Long Island Sound Zone

Science.gov (United States)

2013-04-26

...-AA00 Safety Zones; Fireworks Displays in Captain of the Port Long Island Sound Zone AGENCY: Coast Guard... zones for fireworks displays within the Captain of the Port (COTP) Long Island Sound (LIS) Zone. This... Sector Long Island Sound. DATES: This rule is effective from April 27, 2013, until June 22, 2013. This...

76 FR 34867 - Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone

Science.gov (United States)

2011-06-15

....941(a)(51) Target Fireworks, Detroit, MI The first safety zone will be enforced from 7 a.m. on June 24... Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone AGENCY: Coast Guard, DHS. ACTION: Notice of enforcement of regulation. SUMMARY: The Coast Guard will enforce various safety zones for...

Electrical Grid Stability Enhancement using Smart Home Frequency-response Grid -Friendly Appliance System

Directory of Open Access Journals (Sweden)

Muawiya A. Kaigama

2016-03-01

Full Text Available Load shedding is a powerful scheme used for corrective and preventive measures; corrective to restore system’s stability and preventive to avoid catastrophic failure. However, the affected end users are deprived of power supply absolutely with no choice. This paper presents the design, development, feasibility and merits of Frequency-response Grid -Friendly Appliance System (FRGFAS in a smart home. FRGFAS is a decentralized Adaptive Load Shaving(ALS device that supports grid’s system stability by sensing grid’s frequency deterioration level and turns ON/OFF loads accordingly. The FRGFAS permits end users to carry out load shaving at their scale of preference in smart homes via flexible demand responses and automates outdoor lighting to optimum operational hours. FRGFAS obviate load shedding by shaving loads whenever the system is in distress and reset loads supply to the normal state when it stabilizes, this Consequently increases the end user comfort zone and averts a blackout.

Foam-film-stabilized liquid bridge networks in evaporative lithography and wet granular matter

KAUST Repository

Vakarelski, Ivan Uriev

2013-04-23

Evaporative lithography using latex particle templates is a novel approach for the self-assembly of suspension-dispersed nanoparticles into ordered microwire networks. The phenomenon that drives the self-assembly process is the propagation of a network of interconnected liquid bridges between the template particles and the underlying substrate. With the aid of video microscopy, we demonstrate that these liquid bridges are in fact the border zone between the underlying substrate and foam films vertical to the substrate, which are formed during the evaporation of the liquid from the suspension. The stability of the foam films and thus the liquid bridge network stability are due to the presence of a small amount of surfactant in the evaporating solution. We show that the same type of foam-film-stabilized liquid bridge network can also propagate in 3D clusters of spherical particles, which has important implications for the understanding of wet granular matter. © 2013 American Chemical Society.

76 FR 42048 - Safety Zones; Swimming Events in Captain of the Port Boston Zone

Science.gov (United States)

2011-07-18

...-AA00 Safety Zones; Swimming Events in Captain of the Port Boston Zone AGENCY: Coast Guard, DHS. ACTION... events within the Captain of the Port (COTP) Boston Zone for swimming events. This action is necessary to... property on navigable waters from the hazardous nature of swimming events such as large numbers of swimmers...

Habitable Zones in the Universe

OpenAIRE

Gonzalez, G.

2005-01-01

Habitability varies dramatically with location and time in the universe. This was recognized centuries ago, but it was only in the last few decades that astronomers began to systematize the study of habitability. The introduction of the concept of the habitable zone was key to progress in this area. The habitable zone concept was first applied to the space around a star, now called the Circumstellar Habitable Zone. Recently, other, vastly broader, habitable zones have been proposed. We review...

Practical Methodology for the Inclusion of Nonlinear Slosh Damping in the Stability Analysis of Liquid-Propelled Space Vehicles

Science.gov (United States)

Ottander, John A.; Hall, Robert A.; Powers, J. F.

2018-01-01

A method is presented that allows for the prediction of the magnitude of limit cycles due to adverse control-slosh interaction in liquid propelled space vehicles using non-linear slosh damping. Such a method is an alternative to the industry practice of assuming linear damping and relying on: mechanical slosh baffles to achieve desired stability margins; accepting minimal slosh stability margins; or time domain non-linear analysis to accept time periods of poor stability. Sinusoidal input describing functional analysis is used to develop a relationship between the non-linear slosh damping and an equivalent linear damping at a given slosh amplitude. In addition, a more accurate analytical prediction of the danger zone for slosh mass locations in a vehicle under proportional and derivative attitude control is presented. This method is used in the control-slosh stability analysis of the NASA Space Launch System.

Development and testing of a compartmentalized reaction network model for redox zones in contaminated aquifers

Science.gov (United States)

Abrams , Robert H.; Loague, Keith; Kent, Douglas B.

1998-01-01

The work reported here is the first part of a larger effort focused on efficient numerical simulation of redox zone development in contaminated aquifers. The sequential use of various electron acceptors, which is governed by the energy yield of each reaction, gives rise to redox zones. The large difference in energy yields between the various redox reactions leads to systems of equations that are extremely ill-conditioned. These equations are very difficult to solve, especially in the context of coupled fluid flow, solute transport, and geochemical simulations. We have developed a general, rational method to solve such systems where we focus on the dominant reactions, compartmentalizing them in a manner that is analogous to the redox zones that are often observed in the field. The compartmentalized approach allows us to easily solve a complex geochemical system as a function of time and energy yield, laying the foundation for our ongoing work in which we couple the reaction network, for the development of redox zones, to a model of subsurface fluid flow and solute transport. Our method (1) solves the numerical system without evoking a redox parameter, (2) improves the numerical stability of redox systems by choosing which compartment and thus which reaction network to use based upon the concentration ratios of key constituents, (3) simulates the development of redox zones as a function of time without the use of inhibition factors or switching functions, and (4) can reduce the number of transport equations that need to be solved in space and time. We show through the use of various model performance evaluation statistics that the appropriate compartment choice under different geochemical conditions leads to numerical solutions without significant error. The compartmentalized approach described here facilitates the next phase of this effort where we couple the redox zone reaction network to models of fluid flow and solute transport.

Mechanical properties of fracture zones

International Nuclear Information System (INIS)

Leijon, B.

1993-05-01

Available data on mechanical characteristics of fracture zones are compiled and discussed. The aim is to improve the basis for adequate representation of fracture zones in geomechanical models. The sources of data researched are primarily borehole investigations and case studies in rock engineering, involving observations of fracture zones subjected to artificial load change. Boreholes only yield local information about the components of fracture zones, i.e. intact rock, fractures and various low-strength materials. Difficulties are therefore encountered in evaluating morphological and mechanical properties of fracture zones from borehole data. Although often thought of as macroscopically planar features, available field data consistently show that fracture zones are characterized by geometrical irregularities such as thickness variations, surface undulation and jogs. These irregularities prevail on all scales. As a result, fracture zones are on all scales characterized by large, in-plane variation of strength- and deformational properties. This has important mechanical consequences in terms of non-uniform stress transfer and complex mechanisms of shear deformation. Field evidence for these findings, in particular results from the underground research laboratory in Canada and from studies of induced fault slip in deep mines, is summarized and discussed. 79 refs

Trapped particle stability for the kinetic stabilizer

Science.gov (United States)

Berk, H. L.; Pratt, J.

2011-08-01

A kinetically stabilized axially symmetric tandem mirror (KSTM) uses the momentum flux of low-energy, unconfined particles that sample only the outer end-regions of the mirror plugs, where large favourable field-line curvature exists. The window of operation is determined for achieving magnetohydrodynamic (MHD) stability with tolerable energy drain from the kinetic stabilizer. Then MHD stable systems are analysed for stability of the trapped particle mode. This mode is characterized by the detachment of the central-cell plasma from the kinetic-stabilizer region without inducing field-line bending. Stability of the trapped particle mode is sensitive to the electron connection between the stabilizer and the end plug. It is found that the stability condition for the trapped particle mode is more constraining than the stability condition for the MHD mode, and it is challenging to satisfy the required power constraint. Furthermore, a severe power drain may arise from the necessary connection of low-energy electrons in the kinetic stabilizer to the central region.

Study of tunnelling through water-bearing fracture zones. Baseline study on technical issues with NE-1 as reference

International Nuclear Information System (INIS)

Yanting Chang; Swindell, Robert; Bogdanoff, Ingvar; Lindstroem, Beatrice; Termen, Jens; Starsec, Peter

2005-04-01

, based on the review of the geological and hydrogeological characteristics of the deformation zone NE-1. In the descriptive model, the water-bearing fracture zone consists of an 8 metre wide central core zone and a 15 meter wide transition zone sited on either side of the core zone. Rock mechanical and hydrogeological properties of the rock mass as well as in situ rock stresses are assigned in the descriptive model. To highlight the important technical issues in tunnelling through water-bearing fracture zones, system analysis and problem identification based on a literature review of relevant case histories are conducted. The identified important technical issues, namely large water inflow and tunnel stability, will be the objects to be analysed in this study. Control of water inflows is the key issue for the safe passage of a tunnel through a water-bearing fracture zone with the characteristics of NE-1. Technical issues associated with the two most used methods for water inflow control, namely grouting and ground freezing are discussed. The analyses regarding water inflows associated with grouting are presented. The degree of difficulty for water inflow control increases with depth. The study indicates that control of water inflows at all the depths could be achieved by grouting with current technology. But ground freezing might be an alternative for the core zone, for instance at a depth of 600 metres. Due to the high water pressure that may be encountered at a depth of 600 metres, precautions must be taken in the decision making process in selecting the most appropriate methods of groundwater control. The deformation analysis indicates that large deformations are unlikely to occur in the transition zone, even at a depth of 600 metres. The reduction in rock mass quality in the core zone, however, is likely to result in large deformations at great depths. The estimated mean values of deformation for an unsupported tunnel in the core zone are 60 mm and 130 mm at depths

Study of tunnelling through water-bearing fracture zones. Baseline study on technical issues with NE-1 as reference

Energy Technology Data Exchange (ETDEWEB)

Yanting Chang; Swindell, Robert; Bogdanoff, Ingvar; Lindstroem, Beatrice; Termen, Jens [WSP Sweden, Stockholm (Sweden) ; Starsec, Peter [SGI, Linkoeping (Sweden)

2005-04-01

established, based on the review of the geological and hydrogeological characteristics of the deformation zone NE-1. In the descriptive model, the water-bearing fracture zone consists of an 8 metre wide central core zone and a 15 meter wide transition zone sited on either side of the core zone. Rock mechanical and hydrogeological properties of the rock mass as well as in situ rock stresses are assigned in the descriptive model. To highlight the important technical issues in tunnelling through water-bearing fracture zones, system analysis and problem identification based on a literature review of relevant case histories are conducted. The identified important technical issues, namely large water inflow and tunnel stability, will be the objects to be analysed in this study. Control of water inflows is the key issue for the safe passage of a tunnel through a water-bearing fracture zone with the characteristics of NE-1. Technical issues associated with the two most used methods for water inflow control, namely grouting and ground freezing are discussed. The analyses regarding water inflows associated with grouting are presented. The degree of difficulty for water inflow control increases with depth. The study indicates that control of water inflows at all the depths could be achieved by grouting with current technology. But ground freezing might be an alternative for the core zone, for instance at a depth of 600 metres. Due to the high water pressure that may be encountered at a depth of 600 metres, precautions must be taken in the decision making process in selecting the most appropriate methods of groundwater control. The deformation analysis indicates that large deformations are unlikely to occur in the transition zone, even at a depth of 600 metres. The reduction in rock mass quality in the core zone, however, is likely to result in large deformations at great depths. The estimated mean values of deformation for an unsupported tunnel in the core zone are 60 mm and 130 mm at

Track treeing mechanism and plastic zone in solid Part 1: Initial development of plastic zone

International Nuclear Information System (INIS)

Li Boyang

2008-01-01

After neutron exposure and chemical etching in advance, latent tracks of recoil nucleon develop into pits on CR39 surface. During electrochemical etching, plastic zone is formed at top of pits. Some pits develop into tree cracks in the initial stage of plastic zone development. Physical and mathematical model of crack and plastic zone is proposed; parameter of development free path of plastic zone is presented. Based on integration of elementary theories the stress analysis is build up; based on analyses of measured parameters, a set of common relations between parameters is obtained. Integrate parameter analysis and stress analysis, depth of plastic zone development, law and phenomenon in experimental data can be interpreted completely

77 FR 42176 - Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone

Science.gov (United States)

2012-07-18

... fireworks launch site located at position 41-34'-18.10'' N, 082-51'-18.70'' W (NAD 83). This zone will be... at position 41-34'-18.10'' N, 082- 51'-18.70'' W (NAD 83). (ii) Expected date. This safety zone will...-AA00 Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone AGENCY: Coast Guard...

Effects of hydrated lime on radionuclides stabilization of Hanford tank residual waste.

Science.gov (United States)

Wang, Guohui; Um, Wooyong; Cantrell, Kirk J; Snyder, Michelle M V; Bowden, Mark E; Triplett, Mark B; Buck, Edgar C

2017-10-01

Chemical stabilization of tank residual waste is part of a Hanford Site tank closure strategy to reduce overall risk levels to human health and the environment. In this study, a set of column leaching experiments using tank C-104 residual waste were conducted to evaluate the leachability of uranium (U) and technetium (Tc) where grout and hydrated lime were applied as chemical stabilizing agents. The experiments were designed to simulate future scenarios where meteoric water infiltrates through the vadose zones into the interior of the tank filled with layers of grout or hydrated lime, and then contacts the residual waste. Effluent concentrations of U and Tc were monitored and compared among three different packing columns (waste only, waste + grout, and waste + grout + hydrated lime). Geochemical modeling of the effluent compositions was conducted to determine saturation indices of uranium solid phases that could control the solubility of uranium. The results indicate that addition of hydrated lime strongly stabilized the uranium through transforming uranium to a highly insoluble calcium uranate (CaUO 4 ) or similar phase, whereas no significant stabilization effect of grout or hydrated lime was observed on Tc leachability. The result implies that hydrated lime could be a great candidate for stabilizing Hanford tank residual wastes where uranium is one of the main concerns. Published by Elsevier Ltd.

Sound Zones

DEFF Research Database (Denmark)

Møller, Martin Bo; Olsen, Martin

2017-01-01

Sound zones, i.e. spatially confined regions of individual audio content, can be created by appropriate filtering of the desired audio signals reproduced by an array of loudspeakers. The challenge of designing filters for sound zones is twofold: First, the filtered responses should generate...... an acoustic separation between the control regions. Secondly, the pre- and post-ringing as well as spectral deterioration introduced by the filters should be minimized. The tradeoff between acoustic separation and filter ringing is the focus of this paper. A weighted L2-norm penalty is introduced in the sound...

Conical quarl swirl stabilized non-premixed flames: flame and flow field interaction

KAUST Repository

Elbaz, Ayman M.; Roberts, William L.

2017-01-01

The flame-flow field interaction is studied in non-premixed methane swirl flames stabilized in quartz quarl via simultaneous measurements of the flow field using a stereo PIV and OH-PLIF at 5 KHz repetition rate. Under the same swirl intensity, two flames with different fuel jet velocity were investigated. The time-averaged flow field shows a unique flow pattern at the quarl exit, where two recirculation vortices are formed; a strong recirculation zone formed far from the quarl exit and a larger recirculation zone extending inside the quarl. However, the instantaneous images show that, the flow pattern near the quarl exit plays a vital role in the spatial location and structure of the reaction zone. In the low fuel jet velocity flame, a pair of vortical structures, located precisely at the corners of the quarl exit, cause the flame to roll up into the central region of low speed flow, where the flame sheet then tracks the axial velocity fluctuations. The vorticity field reveals a vortical structure surrounding the reaction zones, which reside on a layer of low compressive strain adjacent to that vortical structure. In the high fuel jet velocity flame, initially a laminar flame sheet resides at the inner shear layer of the main jet, along the interface between incoming fresh gas and high temperature recirculating gas. Further downstream, vortex breakdown alters the flame sheet path toward the central flame region. The lower reaction zones show good correlation to the regions of maximum vorticity and track the regions of low compressive strain associated with the inner shear layer of the jet flow. In both flames the reactions zones conform the passage of the large structure while remaining inside the low speed regions or at the inner shear layer.

Conical quarl swirl stabilized non-premixed flames: flame and flow field interaction

KAUST Repository

Elbaz, Ayman M.

2017-09-19

The flame-flow field interaction is studied in non-premixed methane swirl flames stabilized in quartz quarl via simultaneous measurements of the flow field using a stereo PIV and OH-PLIF at 5 KHz repetition rate. Under the same swirl intensity, two flames with different fuel jet velocity were investigated. The time-averaged flow field shows a unique flow pattern at the quarl exit, where two recirculation vortices are formed; a strong recirculation zone formed far from the quarl exit and a larger recirculation zone extending inside the quarl. However, the instantaneous images show that, the flow pattern near the quarl exit plays a vital role in the spatial location and structure of the reaction zone. In the low fuel jet velocity flame, a pair of vortical structures, located precisely at the corners of the quarl exit, cause the flame to roll up into the central region of low speed flow, where the flame sheet then tracks the axial velocity fluctuations. The vorticity field reveals a vortical structure surrounding the reaction zones, which reside on a layer of low compressive strain adjacent to that vortical structure. In the high fuel jet velocity flame, initially a laminar flame sheet resides at the inner shear layer of the main jet, along the interface between incoming fresh gas and high temperature recirculating gas. Further downstream, vortex breakdown alters the flame sheet path toward the central flame region. The lower reaction zones show good correlation to the regions of maximum vorticity and track the regions of low compressive strain associated with the inner shear layer of the jet flow. In both flames the reactions zones conform the passage of the large structure while remaining inside the low speed regions or at the inner shear layer.

Numerical studies of gas production from several CH4 hydrate zones at the Mallik site, Mackenzie Delta, Canada

Science.gov (United States)

Moridis, G.J.; Collett, T.S.; Dallimore, S.R.; Satoh, T.; Hancock, S.; Weatherill, B.

2004-01-01

The Mallik site represents an onshore permafrost-associated gas hydrate accumulation in the Mackenzie Delta, Northwest Territories, Canada. A gas hydrate research well was drilled at the site in 1998. The objective of this study is the analysis of various gas production scenarios from five methane hydrate-bearing zones at the Mallik site. In Zone #1, numerical simulations using the EOSHYDR2 model indicated that gas production from hydrates at the Mallik site was possible by depressurizing a thin free gas zone at the base of the hydrate stability field. Horizontal wells appeared to have a slight advantage over vertical wells, while multiwell systems involving a combination of depressurization and thermal stimulation offered superior performance, especially when a hot noncondensible gas was injected. Zone #2, which involved a gas hydrate layer with an underlying aquifer, could yield significant amounts of gas originating entirely from gas hydrates, the volumes of which increased with the production rate. However, large amounts of water were also produced. Zones #3, #4 and #5 were lithologically isolated gas hydrate-bearing deposits with no underlying zones of mobile gas or water. In these zones, thermal stimulation by circulating hot water in the well was used to induce dissociation. Sensitivity studies indicated that the methane release from the hydrate accumulations increased with the gas hydrate saturation, the initial formation temperature, the temperature of the circulating water in the well, and the formation thermal conductivity. Methane production appears to be less sensitive to the specific heat of the rock and of the hydrate, and to the permeability of the formation. ?? 2004 Published by Elsevier B.V.

Experimental study of stress-induced localized transformation plastic zones in tetragonal zirconia polycrystalline ceramics

International Nuclear Information System (INIS)

Sun, Q.; Zhao, Z.; Chen, W.; Qing, X.; Xu, X.; Dai, F.

1994-01-01

Stress-induced martensitic transformation plastic zones in ceria-stabilized tetragonal zirconia polycrystalline ceramics (Ce-TZP), under loading conditions of uniaxial tension, compression, and three-point bending, are studied by experiments. The transformed monoclinic phase volume fraction distribution and the corresponding plastic strain distribution and the surface morphology (surface uplift) are measured by means of moire interferometry, Raman microprobe spectroscopy, and the surface measurement system. The experimental results from the above three kinds of specimens and methods consistently show that the stress-induced transformation at room temperature of the above specimen is not uniform within the transformation zone and that the plastic deformation is concentrated in some narrow band; i.e., macroscopic plastic flow localization proceeds during the initial stage of plastic deformation. Flow localization phenomena are all observed in uniaxial tension, compression, and three-point bending specimens. Some implications of the flow localization to the constitutive modeling and toughening of transforming thermoelastic polycrystalline ceramics are explored

Characterizing the physical and genetic structure of the lodgepole pine × jack pine hybrid zone: mosaic structure and differential introgression.

Science.gov (United States)

Cullingham, Catherine I; James, Patrick M A; Cooke, Janice E K; Coltman, David W

2012-12-01

Understanding the physical and genetic structure of hybrid zones can illuminate factors affecting their formation and stability. In north-central Alberta, lodgepole pine (Pinus contorta Dougl. ex Loud. var. latifolia) and jack pine (Pinus banksiana Lamb) form a complex and poorly defined hybrid zone. Better knowledge of this zone is relevant, given the recent host expansion of mountain pine beetle into jack pine. We characterized the zone by genotyping 1998 lodgepole, jack pine, and hybrids from British Columbia, Alberta, Saskatchewan, Ontario, and Minnesota at 11 microsatellites. Using Bayesian algorithms, we calculated genetic ancestry and used this to model the relationship between species occurrence and environment. In addition, we analyzed the ancestry of hybrids to calculate the genetic contribution of lodgepole and jack pine. Finally, we measured the amount of gene flow between the pure species. We found the distribution of the pine classes is explained by environmental variables, and these distributions differ from classic distribution maps. Hybrid ancestry was biased toward lodgepole pine; however, gene flow between the two species was equal. The results of this study suggest that the hybrid zone is complex and influenced by environmental constraints. As a result of this analysis, range limits should be redefined.

33 CFR 165.154 - Safety and Security Zones: Long Island Sound Marine Inspection Zone and Captain of the Port Zone.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety and Security Zones: Long... Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PORTS AND WATERWAYS SAFETY... Areas First Coast Guard District § 165.154 Safety and Security Zones: Long Island Sound Marine...

Compact and Light-Weight Solar Spaceflight Instrument Designs Utilizing Newly Developed Miniature Free-Standing Zone Plates: EUV Radiometer and Limb-Scanning Monochromator

Science.gov (United States)

Seely, J. F.; McMullin, D. R.; Bremer, J.; Chang, C.; Sakdinawat, A.; Jones, A. R.; Vest, R.

2014-12-01

Two solar instrument designs are presented that utilize newly developed miniature free-standing zone plates having interconnected Au opaque bars and no support membrane resulting in excellent long-term stability in space. Both instruments are based on a zone plate having 4 mm outer diameter and 1 to 2 degree field of view. The zone plate collects EUV radiation and focuses a narrow bandpass through a pinhole aperture and onto a silicon photodiode detector. As a miniature radiometer, EUV irradiance is accurately determined from the zone plate efficiency and the photodiode responsivity that are calibrated at the NIST SURF synchrotron facility. The EUV radiometer is pointed to the Sun and measures the absolute solar EUV irradiance in high time cadence suitable for solar physics and space weather applications. As a limb-scanning instrument in low earth orbit, a miniature zone-plate monochromator measures the extinction of solar EUV radiation by scattering through the upper atmosphere which is a measure of the variability of the ionosphere. Both instruments are compact and light-weight and are attractive for CubeSats and other missions where resources are extremely limited.

A comparative study to evaluate the effect of two different abutment designs on soft tissue healing and stability of mucosal margins

NARCIS (Netherlands)

Patil, Ratnadeep; van Brakel, Ralph; Iyer, Kavita; Huddleston Slater, James; de Putter, Cornelis; Cune, Marco

Aim To evaluate the effect of two different abutment designs on soft tissue healing and the stability of the mucosal margin in vivo. Materials and methods Twenty-nine subjects received two, non-adjacent endosseous implants in the esthetic zone. Subsequently, conventional (control) and curved

33 CFR 165.20 - Safety zones.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety zones. 165.20 Section 165... WATERWAYS SAFETY REGULATED NAVIGATION AREAS AND LIMITED ACCESS AREAS Safety Zones § 165.20 Safety zones. A Safety Zone is a water area, shore area, or water and shore area to which, for safety or environmental...

Zone distillation: a new purification method

International Nuclear Information System (INIS)

Kravchenko, A.I.

2011-01-01

The features of zone distillation (with zone melting of refined material and with pulling of condensate) as a new purification method are shown. The method is based on similarity of equations of distillation and crystallization refining. The analogy between some distillation and condensation methods (particularly between zone distillation and zone recrystallization) is should up

Climate stability and sensitivity in some simple conceptual models

Energy Technology Data Exchange (ETDEWEB)

Bates, J. Ray [University College Dublin, Meteorology and Climate Centre, School of Mathematical Sciences, Dublin (Ireland)

2012-02-15

A theoretical investigation of climate stability and sensitivity is carried out using three simple linearized models based on the top-of-the-atmosphere energy budget. The simplest is the zero-dimensional model (ZDM) commonly used as a conceptual basis for climate sensitivity and feedback studies. The others are two-zone models with tropics and extratropics of equal area; in the first of these (Model A), the dynamical heat transport (DHT) between the zones is implicit, in the second (Model B) it is explicitly parameterized. It is found that the stability and sensitivity properties of the ZDM and Model A are very similar, both depending only on the global-mean radiative response coefficient and the global-mean forcing. The corresponding properties of Model B are more complex, depending asymmetrically on the separate tropical and extratropical values of these quantities, as well as on the DHT coefficient. Adopting Model B as a benchmark, conditions are found under which the validity of the ZDM and Model A as climate sensitivity models holds. It is shown that parameter ranges of physical interest exist for which such validity may not hold. The 2 x CO{sub 2} sensitivities of the simple models are studied and compared. Possible implications of the results for sensitivities derived from GCMs and palaeoclimate data are suggested. Sensitivities for more general scenarios that include negative forcing in the tropics (due to aerosols, inadvertent or geoengineered) are also studied. Some unexpected outcomes are found in this case. These include the possibility of a negative global-mean temperature response to a positive global-mean forcing, and vice versa. (orig.)

46 CFR 76.23-5 - Zoning.

Science.gov (United States)

2010-10-01

... deck, large common areas may be zoned in accordance with table 76.23-5(b). All such zones within one common area shall be of approximately the same size. Zones of this type shall overlap in such a manner that the end sprinkler heads of both adjoining zones will cover the identical area. Table 76.23-5(b...

Ecology-genetic consequences of the chronic irradiation of animals in Chernobyl alienation zone

International Nuclear Information System (INIS)

Glazko, V.I.; Grodzinskij, D.M.; Glazko, T.T.

2006-01-01

The investigation with the use of different molecular-genetic markers and the cytogenetic analysis of genetic-population consequences in different species of voles and experimental cattle herd reproduced in Chernobyl's alienation zone is carried out. The decrease in the number of animals with cytogenetic anomalies in bone marrow cells in voles, was revealed, that testified to the selection by the radioresistance. The obtained data allow us to make conclusion that the increase of ionizing radiation is a particular case of ecological changes leading to the microevolution events connected with the selection by the stability to new conditions of the reproduction of populations

Effect of Silicon on Intergranular Corrosion Resistance of Ti-stabilized 11 wt% Cr Ferritic Stainless Steels

International Nuclear Information System (INIS)

Hyun, Youngmin; Kim, Heesan

2013-01-01

Ti-stabilized 11 wt% Cr ferritic stainless steels (FSSs) for automotive exhaust systems have been experienced intergranular corrosion (IC) in some heat-affected zone (HAZ). The effects of sensitizing heat-treatment and silicon on IC were studied. Time-Temperature-Sensitization (TTS) curves showed that sensitization to IC was observed at the steels heat-treated at the temperature lower than 650 .deg. C and that silicon improved IC resistance. The sensitization was explained by chromium depletion theory, where chromium is depleted by precipitation of chromium carbide during sensitizing heat-treatment. It was confirmed with the results from the analysis of precipitates as well as the thermodynamical prediction of stable phases. In addition, the role of silicon on IC was explained with the stabilization of grain boundary. In other words, silicon promoted the formation of the grain boundaries with low energy where precipitation was suppressed and consequently, the formation of Cr-depleted zone was retarded. The effect of silicon on the formation of grain boundaries with low energy was proved by the analysis of coincidence site lattice (CSL) grain boundary, which is a typical grain boundary with low energy

Effect of Silicon on Intergranular Corrosion Resistance of Ti-stabilized 11 wt% Cr Ferritic Stainless Steels

Energy Technology Data Exchange (ETDEWEB)

Hyun, Youngmin; Kim, Heesan [Hongik Univ., Sejong (Korea, Republic of)

2013-06-15

Ti-stabilized 11 wt% Cr ferritic stainless steels (FSSs) for automotive exhaust systems have been experienced intergranular corrosion (IC) in some heat-affected zone (HAZ). The effects of sensitizing heat-treatment and silicon on IC were studied. Time-Temperature-Sensitization (TTS) curves showed that sensitization to IC was observed at the steels heat-treated at the temperature lower than 650 .deg. C and that silicon improved IC resistance. The sensitization was explained by chromium depletion theory, where chromium is depleted by precipitation of chromium carbide during sensitizing heat-treatment. It was confirmed with the results from the analysis of precipitates as well as the thermodynamical prediction of stable phases. In addition, the role of silicon on IC was explained with the stabilization of grain boundary. In other words, silicon promoted the formation of the grain boundaries with low energy where precipitation was suppressed and consequently, the formation of Cr-depleted zone was retarded. The effect of silicon on the formation of grain boundaries with low energy was proved by the analysis of coincidence site lattice (CSL) grain boundary, which is a typical grain boundary with low energy.

Chemical stabilization of metals and arsenic in contaminated soils using oxides – A review

International Nuclear Information System (INIS)

Komárek, Michael; Vaněk, Aleš; Ettler, Vojtěch

2013-01-01

Oxides and their precursors have been extensively studied, either singly or in combination with other amendments promoting sorption, for in situ stabilization of metals and As in contaminated soils. This remediation option aims at reducing the available fraction of metal(loid)s, notably in the root zone, and thus lowering the risks associated with their leaching, ecotoxicity, plant uptake and human exposure. This review summarizes literature data on mechanisms involved in the immobilization process and presents results from laboratory and field experiments, including the subsequent influence on higher plants and aided phytostabilization. Despite the partial successes in the field, recent knowledge highlights the importance of long-term and large-scale field studies evaluating the stability of the oxide-based amendments in the treated soils and their efficiency in the long-term. - In situ stabilization of metals and As in contaminated soils using oxides combined with phytostabilization is a potential alternative to conventional remediation techniques.

33 CFR 3.25-10 - Sector Hampton Roads Marine Inspection Zone and Captain of the Port Zone.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Sector Hampton Roads Marine... ZONES, AND CAPTAIN OF THE PORT ZONES Fifth Coast Guard District § 3.25-10 Sector Hampton Roads Marine Inspection Zone and Captain of the Port Zone. Sector Hampton Roads' office is located in Portsmouth, VA. The...

The role of heat transfer time scale in the evolution of the subsea permafrost and associated methane hydrates stability zone during glacial cycles

Science.gov (United States)

Malakhova, Valentina V.; Eliseev, Alexey V.

2017-10-01

Climate warming may lead to degradation of the subsea permafrost developed during Pleistocene glaciations and release methane from the hydrates, which are stored in this permafrost. It is important to quantify time scales at which this release is plausible. While, in principle, such time scale might be inferred from paleoarchives, this is hampered by considerable uncertainty associated with paleodata. In the present paper, to reduce such uncertainty, one-dimensional simulations with a model for thermal state of subsea sediments forced by the data obtained from the ice core reconstructions are performed. It is shown that heat propagates in the sediments with a time scale of ∼ 10-20 kyr. This time scale is longer than the present interglacial and is determined by the time needed for heat penetration in the unfrozen part of thick sediments. We highlight also that timings of shelf exposure during oceanic regressions and flooding during transgressions are important for simulating thermal state of the sediments and methane hydrates stability zone (HSZ). These timings should be resolved with respect to the contemporary shelf depth (SD). During glacial cycles, the temperature at the top of the sediments is a major driver for moving the HSZ vertical boundaries irrespective of SD. In turn, pressure due to oceanic water is additionally important for SD ≥ 50 m. Thus, oceanic transgressions and regressions do not instantly determine onsets of HSZ and/or its disappearance. Finally, impact of initial conditions in the subsea sediments is lost after ∼ 100 kyr. Our results are moderately sensitive to intensity of geothermal heat flux.

About the walking machine motion stability

Directory of Open Access Journals (Sweden)

V. V. Lapshin

2014-01-01

Full Text Available The use of legs as propulsive devices of the machine will increase its capability to cross rough and deformable terrain as compared with wheeled and trucked machines. Today it is already possible to speak about design of statically stable walking robots to be used in the certain areas of application. The most promising areas of their application are exploration and emergency-rescue operations in extremely complicated situations (e.g. in the zone of destruction after earthquakes, technogenic catastrophe, etc..In such dangerous situations there is a possibility for the walking machine to be overturned either because of loosing a support to one or several legs or due to significant displacement of the leg support points, which are caused by deformation or destruction of the terrain in the points of the legs support. Therefore, it is necessary to design motion control algorithms that enable teaching the motion control system of a walking robot: How to decrease the possibility of the robot overturning? How to stop the robot as quickly as possible keeping its static stability? What must be done if static stability is lost? Note that the loss of static stability does not inevitably result in the robot falling down. How to fall down better (with minimal robot destruction in inevitable case?This work investigates the first abovementioned problems, i.e. preventing a walking machine from overturning in dangerous situations. For this purpose it suggests to use a special cautious (safe gait, which allows the machine to remain statically stable if it suddenly looses support to its any leg. The natural price for the increased safety to prevent from overturning is the reduced capabilities of robot kinematics and, as a consequence, its capability to cross rough terrain. It is also suggested to reconsider the general definition of a walking machine static stability margin in order to obtain an adequate estimation of the robot overturning possibility

Irradiation damage 'displacement zone'; Dommages sous irradiation zone de deplacements

Energy Technology Data Exchange (ETDEWEB)

Genthon, J P [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1969-07-01

It is well known that a charged particle (ion, primary atom, etc...) moving in a solid slows down and can cause a cascade of displacements of the atoms in the solid. A study is made here of the extent to which the cascade is made up, or not, of independent collisions, as a function of the energy of the initial charged particle. When the distance between the collisions is small, these latter are no longer independent; the cascade, which then has to be considered as a whole, perturbs and locates, in the irradiated solid , a zone which has been named a 'displacement zone'. It is shown that the proportion of displacement zones increases with increasing atom size (high atomic number Z), with decreasing atomic distance D in the substance considered and with decreasing energy of the ion undergoing the slowing down process (although always remaining above a few hundred eV). The proportions obtained are higher than those corresponding to the calculations of J. A. Brinkman [3]. An interatomic potential required for this work has also been determined. (author) [French] On sait qu'une particule chargee (ions, atomes primaires, etc...) en mouvement dans un solide se ralentit, avec eventuellement deplacement en cascade d'atomes du solide. On etudie ici dans quelle proportion, en fonction de l'energie de la particule chargee initiale, la cascade est constituee, ou non, de 'chocs independants'. Lorsque la distance entre chocs est petite, ceux-ci ne sont plus independants; la cascade, qui doit alors etre consideree dans son ensemble, perturbe et definit dans le solide irradie, une zone qu'on a appele zone de deplacements. On montre que la proportion de zones de deplacements est d'autant plus grande que les atomes sont gros (nombre atomique Z grand), que la distance interatomique D est petite dans le corps considere, et que l'energie de l'ion en ralentissement est petite (tout en restant superieure a quelques centaines d'eV). Les proportions obtenues sont superieures a celles qui

Numerical estimation of stability and improvement for coolant passage design in Hollow type CICC; Hollow gata CICC no reikyaku ryuro kaizen to anteisei no suchiteki kento

Energy Technology Data Exchange (ETDEWEB)

Miyauchi, M. [Yamagata Univ., Yamagata (Japan); Yoshiki, H. [The Univ. of Tokyo, Tokyo (Japan)

1999-06-07

The Hollow type CICC has a central channel (Hole) and is separated from surrounding bundle by a spiral tape with a gap, heat of a strand can effectively be convected to the Hole zone. However, even strong convection currents are induced in two ends of a thermal generating zone, but the heat is accumulated in the central part, and stability margin drops while relatively a long time heat has input for about 100 msec. In this study, the helium deposit inside the heating zone is reduced by a little design changing of the spiral tape that separates the bundle and the hole and efforts of improving stability of low energy density against heating are attempted. The instability caused by low energy and a long time heat invasion of the CICC appears also in simulation of Zanino at el. using a MITHRANDIR code. At this time, a method for calculating overflow of helium flowing to the bundle/Hole taking references of a branch current model and a joint flow model that are used in engine simulations is developed. (NEDO)

Oxygenated gasoline release in the unsaturated zone - Part 1: Source zone behavior.

Science.gov (United States)

Freitas, Juliana G; Barker, James F

2011-11-01

Oxygenates present in gasoline, such as ethanol and MTBE, are a concern in subsurface contamination related to accidental spills. While gasoline hydrocarbon compounds have low solubility, MTBE and ethanol are more soluble, ethanol being completely miscible with water. Consequently, their fate in the subsurface is likely to differ from that of gasoline. To evaluate the fate of gasoline containing oxygenates following a release in the unsaturated zone shielded from rainfall/recharge, a controlled field test was performed at Canadian Forces Base Borden, in Ontario. 200L of a mixture composed of gasoline with 10% ethanol and 4.5% MTBE was released in the unsaturated zone, into a trench 20cm deep, about 32cm above the water table. Based on soil cores, most of the ethanol was retained in the source, above the capillary fringe, and remained there for more than 100 days. Ethanol partitioned from the gasoline to the unsaturated pore-water and was retained, despite the thin unsaturated zone at the site (~35cm from the top of the capillary fringe to ground surface). Due to its lower solubility, most of the MTBE remained within the NAPL as it infiltrated deeper into the unsaturated zone and accumulated with the gasoline on top of the depressed capillary fringe. Only minor changes in the distribution of ethanol were noted following oscillations in the water table. Two methods to estimate the capacity of the unsaturated zone to retain ethanol are explored. It is clear that conceptual models for sites impacted by ethanol-fuels must consider the unsaturated zone. Copyright © 2011 Elsevier B.V. All rights reserved.

Work zone safety analysis.

Science.gov (United States)

2013-11-01

This report presents research performed analyzing crashes in work zones in the state of New Jersey so as to : identify critical areas in work zones susceptible to crashes and key factors that contribute to these crashes. A field : data collection on ...

Site-specific to local-scale shallow landslides triggering zones assessment using TRIGRS

Science.gov (United States)

Bordoni, M.; Meisina, C.; Valentino, R.; Bittelli, M.; Chersich, S.

2015-05-01

Rainfall-induced shallow landslides are common phenomena in many parts of the world, affecting cultivation and infrastructure and sometimes causing human losses. Assessing the triggering zones of shallow landslides is fundamental for land planning at different scales. This work defines a reliable methodology to extend a slope stability analysis from the site-specific to local scale by using a well-established physically based model (TRIGRS-unsaturated). The model is initially applied to a sample slope and then to the surrounding 13.4 km2 area in Oltrepo Pavese (northern Italy). To obtain more reliable input data for the model, long-term hydro-meteorological monitoring has been carried out at the sample slope, which has been assumed to be representative of the study area. Field measurements identified the triggering mechanism of shallow failures and were used to verify the reliability of the model to obtain pore water pressure trends consistent with those measured during the monitoring activity. In this way, more reliable trends have been modelled for past landslide events, such as the April 2009 event that was assumed as a benchmark. The assessment of shallow landslide triggering zones obtained using TRIGRS-unsaturated for the benchmark event appears good for both the monitored slope and the whole study area, with better results when a pedological instead of geological zoning is considered at the regional scale. The sensitivity analyses of the influence of the soil input data show that the mean values of the soil properties give the best results in terms of the ratio between the true positive and false positive rates. The scheme followed in this work allows us to obtain better results in the assessment of shallow landslide triggering areas in terms of the reduction in the overestimation of unstable zones with respect to other distributed models applied in the past.

Interfacial Reduction-Oxidation Mechanisms Governing Fate and Transport of Contaminants in the Vadose Zone

Energy Technology Data Exchange (ETDEWEB)

Principal Investigator: Baolin Deng, University of Missouri, Columbia, MO; Co-Principal Investigator: Silvia Sabine Jurisson, University of Missouri, Columbia, MO; Co-Principal Investigator: Edward C. Thornton, Pacific Northwest National Laboratory Richland, WA; Co-Principal Investigator: Jeff Terry, Illinois Institute of Technology, Chicago, IL

2008-05-12

There are many soil contamination sites at the Department of Energy (DOE) installations that contain radionuclides and toxic metals such as uranium (U), technetium (Tc), and chromium (Cr). Since these contaminants are the main 'risk drivers' at the Hanford site (WA) and some of them also pose significant risk at other DOE facilities (e.g., Oak Ridge Reservation - TN; Rocky Flats - CO), development of technologies for cost effective site remediation is needed. Current assessment indicates that complete removal of these contaminants for ex-situ disposal is infeasible, thus in-situ stabilization through reduction to insoluble species is considered one of the most important approaches for site remediation. In Situ Gaseous Reduction (ISGR) is a technology developed by Pacific Northwest National Laboratory (PNNL) for vadose zone soil remediation. The ISGR approach uses hydrogen sulfide (H{sub 2}S) for reductive immobilization of contaminants that show substantially lower mobility in their reduced forms (e.g., Tc, U, and Cr). The technology can be applied in two ways: (i) to immobilize or stabilize pre-existing contaminants in the vadose zone soils by direct H{sub 2}S treatment, or (ii) to create a permeable reactive barrier (PRB) that prevents the migration of contaminants. Direct treatment involves reduction of the contaminants by H{sub 2}S to less mobile species. Formation of a PRB is accomplished through reduction of ferric iron species in the vadose zone soils by H{sub 2}S to iron sulfides (e.g., FeS), which provides a means for capturing the contaminants entering the treated zone. Potential future releases may occur during tank closure activities. Thus, the placement of a permeable reactive barrier by ISGR treatment can be part of the leak mitigation program. Deployment of these ISGR approaches, however, requires a better understanding of the immobilization kinetics and mechanisms, and a better assessment of the long-term effectiveness of treatment. The

Unsaturated Zone and Saturated Zone Transport Properties (U0100)

Energy Technology Data Exchange (ETDEWEB)

J. Conca

2000-12-20

This Analysis/Model Report (AMR) summarizes transport properties for the lower unsaturated zone hydrogeologic units and the saturated zone at Yucca Mountain and provides a summary of data from the Busted Butte Unsaturated Zone Transport Test (UZTT). The purpose of this report is to summarize the sorption and transport knowledge relevant to flow and transport in the units below Yucca Mountain and to provide backup documentation for the sorption parameters decided upon for each rock type. Because of the complexity of processes such as sorption, and because of the lack of direct data for many conditions that may be relevant for Yucca Mountain, data from systems outside of Yucca Mountain are also included. The data reported in this AMR will be used in Total System Performance Assessment (TSPA) calculations and as general scientific support for various Process Model Reports (PMRs) requiring knowledge of the transport properties of different materials. This report provides, but is not limited to, sorption coefficients and other relevant thermodynamic and transport properties for the radioisotopes of concern, especially neptunium (Np), plutonium (Pu), Uranium (U), technetium (Tc), iodine (I), and selenium (Se). The unsaturated-zone (UZ) transport properties in the vitric Calico Hills (CHv) are discussed, as are colloidal transport data based on the Busted Butte UZTT, the saturated tuff, and alluvium. These values were determined through expert elicitation, direct measurements, and data analysis. The transport parameters include information on interactions of the fractures and matrix. In addition, core matrix permeability data from the Busted Butte UZTT are summarized by both percent alteration and dispersion.

Unsaturated Zone and Saturated Zone Transport Properties (U0100)

International Nuclear Information System (INIS)

Conca, J.

2000-01-01

This Analysis/Model Report (AMR) summarizes transport properties for the lower unsaturated zone hydrogeologic units and the saturated zone at Yucca Mountain and provides a summary of data from the Busted Butte Unsaturated Zone Transport Test (UZTT). The purpose of this report is to summarize the sorption and transport knowledge relevant to flow and transport in the units below Yucca Mountain and to provide backup documentation for the sorption parameters decided upon for each rock type. Because of the complexity of processes such as sorption, and because of the lack of direct data for many conditions that may be relevant for Yucca Mountain, data from systems outside of Yucca Mountain are also included. The data reported in this AMR will be used in Total System Performance Assessment (TSPA) calculations and as general scientific support for various Process Model Reports (PMRs) requiring knowledge of the transport properties of different materials. This report provides, but is not limited to, sorption coefficients and other relevant thermodynamic and transport properties for the radioisotopes of concern, especially neptunium (Np), plutonium (Pu), Uranium (U), technetium (Tc), iodine (I), and selenium (Se). The unsaturated-zone (UZ) transport properties in the vitric Calico Hills (CHv) are discussed, as are colloidal transport data based on the Busted Butte UZTT, the saturated tuff, and alluvium. These values were determined through expert elicitation, direct measurements, and data analysis. The transport parameters include information on interactions of the fractures and matrix. In addition, core matrix permeability data from the Busted Butte UZTT are summarized by both percent alteration and dispersion

Correlation Between Intercritical Heat-Affected Zone and Type IV Creep Damage Zone in Grade 91 Steel

Science.gov (United States)

Wang, Yiyu; Kannan, Rangasayee; Li, Leijun

2018-04-01

A soft zone in Cr-Mo steel weldments has been reported to accompany the infamous Type IV cracking, the highly localized creep damage in the heat-affected zone of creep-resistant steels. However, the microstructural features and formation mechanism of this soft zone are not well understood. In this study, using microhardness profiling and microstructural verification, the initial soft zone in the as-welded condition was identified to be located in the intercritical heat-affected zone of P91 steel weldments. It has a mixed structure, consisting of Cr-rich re-austenitized prior austenite grains and fine Cr-depleted, tempered martensite grains retained from the base metal. The presence of these further-tempered retained grains, originating from the base metal, is directly responsible for the hardness reduction of the identified soft zone in the as-welded condition. The identified soft zone exhibits a high location consistency at three thermal stages. Local chemistry analysis and thermodynamic calculation show that the lower chromium concentrations inside these retained grains thermodynamically decrease their potentials for austenitic transformation during welding. Heterogeneous grain growth is observed in the soft zone during postweld heat treatment. The mismatch of strengths between the weak Cr-depleted grains and strong Cr-rich grains enhances the creep damage. Local deformation of the weaker Cr-depleted grains accelerates the formation of creep cavities.

Women in Chernobyl Exclusion Zone

International Nuclear Information System (INIS)

Balashevska, Y.; Kireev, S.; Navalikhin, V.

2015-01-01

Today, 29 years after the Chernobyl accident, the Exclusion Zone still remains an areal unsealed radiation source of around 2600 km"2. It is not just a gigantic radioactive waste storage facility (the amount of radioactive waste accumulated within the Zone, except for the Shelter, is estimated at about 2.8 million m"3), but also a unique research and engineering platform for biologists, radiologists, chemists and physicists. Taking into account the amount of the radionuclides released during the accident, it becomes quite understood that the radiological environment in the Exclusion Zone is far from favorable. However, among the Exclusion Zone personnel who numbers 5000, there are female workers. The poster represents the results of the research performed among the female employees of the largest enterprise of the Exclusion Zone, “Chornobyl Spetskombinat”. The survey was performed with the view to knowing what makes women work in the most radioactively contaminated area in Europe, and what their role is, to revealing their fears and hopes, and to estimating the chances of the brave women of Chernobyl Exclusion Zone to succeed in their careers. (author)

Problems of Chernobyl Exclusion Zone

International Nuclear Information System (INIS)

Kholosha, V.Yi.

2014-01-01

The collection comprises the results of researches and design activity in the ChNPP exclusion zone, aimed at the development of technologies, equipment and devices for radioactive waste management and ChNPP accident clean-up, at studying the composition and structure of the Exclusion zone soil activity solid bearers, form transformation of the fission products of fuel fallout radionuclide composition in the ChNPP near zone, the spatial distribution of radionuclides and other radioecological issues.. Much attention is paid to medical and biological aspects of the accident influence on the flora, fauna and people's health, labour conditions and incidence of the workers of the Exclusion zone

75 FR 19304 - Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone

Science.gov (United States)

2010-04-14

... previously published in Coast Guard regulations. These safety zones are necessary to protect spectators...-AA00 Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone AGENCY: Coast Guard, DHS. ACTION: Notice of proposed rulemaking. SUMMARY: The Coast Guard proposes establishment of safety...

A viscoplastic shear-zone model for episodic slow slip events in oceanic subduction zones

Science.gov (United States)

Yin, A.; Meng, L.

2016-12-01

Episodic slow slip events occur widely along oceanic subduction zones at the brittle-ductile transition depths ( 20-50 km). Although efforts have been devoted to unravel their mechanical origins, it remains unclear about the physical controls on the wide range of their recurrence intervals and slip durations. In this study we present a simple mechanical model that attempts to account for the observed temporal evolution of slow slip events. In our model we assume that slow slip events occur in a viscoplastic shear zone (i.e., Bingham material), which has an upper static and a lower dynamic plastic yield strength. We further assume that the hanging wall deformation is approximated as an elastic spring. We envision the shear zone to be initially locked during forward/landward motion but is subsequently unlocked when the elastic and gravity-induced stress exceeds the static yield strength of the shear zone. This leads to backward/trenchward motion damped by viscous shear-zone deformation. As the elastic spring progressively loosens, the hanging wall velocity evolves with time and the viscous shear stress eventually reaches the dynamic yield strength. This is followed by the termination of the trenchward motion when the elastic stress is balanced by the dynamic yield strength of the shear zone and the gravity. In order to account for the zig-saw slip-history pattern of typical repeated slow slip events, we assume that the shear zone progressively strengthens after each slow slip cycle, possibly caused by dilatancy as commonly assumed or by progressive fault healing through solution-transport mechanisms. We quantify our conceptual model by obtaining simple analytical solutions. Our model results suggest that the duration of the landward motion increases with the down-dip length and the static yield strength of the shear zone, but decreases with the ambient loading velocity and the elastic modulus of the hanging wall. The duration of the backward/trenchward motion depends

Sediment-stabilizing and Destabilizing Ecoengineering Species from River to Estuary: the Case of the Scheldt System

Science.gov (United States)

Selakovic, S.; Cozzoli, F.; Leuven, J.; Van Braeckel, A.; Speybroeck, J.; Kleinhans, M. G.; Bouma, T.

2017-12-01

Interactions between organisms and landscape forming processes play an important role in evolution of coastal landscapes. In particular, biota has a strong potential to interact with important geomorphological processes such as sediment dynamics. Although many studies worked towards quantifying the impact of different species groups on sediment dynamics, information has been gathered on an ad hoc base. Depending on species' traits and distribution, functional groups of ecoengineering species may have differential effects on sediment deposition and erosion. We hypothesize that the spatial distributions of sediment-stabilizing and destabilizing species across the channel and along the whole salinity gradient of an estuary partly determine the planform shape and channel-shoal morphology of estuaries. To test this hypothesis, we analyze vegetation and macrobenthic data taking the Scheldt river-estuarine continuum as model ecosystem. We identify species traits with important effects on sediment dynamics and use them to form functional groups. By using linearized mixed modelling, we are able to accurately describe the distributions of the different functional groups. We observe a clear distinction of dominant ecosystem engineering functional groups and their potential effects on the sediment in the river-estuarine continuum. The first results of longitudinal cross section show the highest effects of stabilizing plant species in riverine and sediment bioturbators in weak polyhaline part of continuum. The distribution of functional groups in transverse cross sections shows dominant stabilizing effect in supratidal zone compared to dominant destabilizing effect in the lower intertidal zone. This analysis offers a new and more general conceptualization of distributions of sediment stabilizing and destabilizing functional groups and their potential impacts on sediment dynamics, shoal patterns, and planform shapes in river-estuarine continuum. We intend to test this in future

Coastal zone

International Nuclear Information System (INIS)

2002-01-01

The report entitled Climate Change Impacts and Adaptation : A Canadian Perspective, presents a summary of research regarding the impacts of climate change on key sectors over the past five years as it relates to Canada. This chapter on the coastal zone focuses on the impact of climate change on Canada's marine and Great Lakes coasts with tips on how to deal with the impacts associated with climate change in sensitive environments. This report is aimed at the sectors that will be most affected by adaptation decisions in the coastal zone, including fisheries, tourism, transportation and water resources. The impact of climate change in the coastal zone may include changes in water levels, wave patterns, storm surges, and thickness of seasonal ice cover. The Intergovernmental Panel on Climate Change projects global average sea level will rise between 9 and 88 centimetres between 1990 to 2100, but not all areas of Canada will experience the same rate of future sea level change. The main physical impact would be shoreline change that could result in a range of biophysical and socio-economic impacts, some beneficial, some negative. The report focuses on issues related to infrastructure and communities in coastal regions. It is noted that appropriate human adaptation will play a vital role in reducing the extent of potential impacts by decreasing the vulnerability of average zone to climate change. The 3 main trends in coastal adaptation include: (1) increase in soft protection, retreat and accommodation, (2) reliance on technology such as geographic information systems to manage information, and (3) awareness of the need for coastal adaptation that is appropriate for local conditions. 61 refs., 7 figs

Louisiana Speaks Regional Plan Vision Special Economic Zones, UTM Zone 15N NAD83, Louisiana Recovery Authority (2007), [louisiana_speaks_vision_special_economic_zones

Data.gov (United States)

Louisiana Geographic Information Center — This GIS shapefile data illustrates special economic zones included in the Louisiana Speaks Regional Plan Vision. Special economic zones include existing national,...

Influence of Metal Transfer Stability and Shielding Gas Composition on CO and CO2 Emissions during Short-circuiting MIG/MAG Welding

Directory of Open Access Journals (Sweden)

Valter Alves de Meneses

Full Text Available Abstract: Several studies have demonstrated the influence of parameters and shielding gas on metal transfer stability or on the generation of fumes in MIG/MAG welding, but little or nothing has been discussed regarding the emission of toxic and asphyxiating gases, particularly as it pertains to parameterization of the process. The purpose of this study was to analyze and evaluate the effect of manufacturing aspects of welding processes (short-circuit metal transfer stability and shielding gas composition on the gas emission levels during MIG/MAG welding (occupational health and environmental aspects. Using mixtures of Argon with CO2 and O2 and maintaining the same average current and the same weld bead volume, short-circuit welding was performed with carbon steel welding wire in open (welder’s breathing zone and confined environments. The welding voltage was adjusted to gradually vary the transfer stability. It was found that the richer the composition of the shielding gas is in CO2, the more CO and CO2 are generated by the arc. However, unlike fume emission, voltage and transfer stability had no effect on the generation of these gases. It was also found that despite the large quantity of CO and CO2 emitted by the arc, especially when using pure CO2 shielding gas, there was no high level residual concentration of CO and CO2 in or near the worker’s breathing zone, even in confined work cells.

77 FR 9528 - Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound

Science.gov (United States)

2012-02-17

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket No. USCG-2012-0087] Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound AGENCY: Coast Guard, DHS... Waterway Security Zone in Commencement Bay, Tacoma, Washington from 6 a.m. on February 17, 2012, through 11...

78 FR 40396 - Safety Zone; America's Cup Safety Zone and No Loitering Area, San Francisco, CA

Science.gov (United States)

2013-07-05

...-AA00 Safety Zone; America's Cup Safety Zone and No Loitering Area, San Francisco, CA AGENCY: Coast... America's Cup races. This safety zone and no loitering area are established to enhance the safety of spectators and mariners near the north east corner of the America's Cup regulated area. All persons or...

Turbulent piloted partially-premixed flames with varying levels of O2/N2: stability limits and PDF calculations

Science.gov (United States)

Juddoo, Mrinal; Masri, Assaad R.; Pope, Stephen B.

2011-12-01

This paper reports measured stability limits and PDF calculations of piloted, turbulent flames of compressed natural gas (CNG) partially-premixed with either pure oxygen, or with varying levels of O2/N2. Stability limits are presented for flames of CNG fuel premixed with up to 20% oxygen as well as CNG-O2-N2 fuel where the O2 content is varied from 8 to 22% by volume. Calculations are presented for (i) Sydney flame B [Masri et al. 1988] which uses pure CNG as well as flames B15 to B25 where the CNG is partially-premixed with 15-25% oxygen by volume, respectively and (ii) Sandia methane-air (1:3 by volume) flame E [Barlow et al. 2005] as well as new flames E15 and E25 that are partially-premixed with 'reconstituted air' where the O2 content in nitrogen is 15 and 25% by volume, respectively. The calculations solve a transported PDF of composition using a particle-based Monte Carlo method and employ the EMST mixing model as well as detailed chemical kinetics. The addition of oxygen to the fuel increases stability, shortens the flames, broadens the reaction zone, and shifts the stoichiometric mixture fraction towards the inner side of the jet. It is found that for pure CNG flames where the reaction zone is narrow (∼0.1 in mixture fraction space), the PDF calculations fail to reproduce the correct level of local extinction on approach to blow-off. A broadening in the reaction zone up to about 0.25 in mixture fraction space is needed for the PDF/EMST approach to be able to capture these finite-rate chemistry effects. It is also found that for the same level of partial premixing, increasing the O2/N2 ratio increases the maximum levels of CO and NO but shifts the peak to richer mixture fractions. Over the range of oxygenation investigated here, stability limits have shown to improve almost linearly with increasing oxygen levels in the fuel and with increasing the contribution of release rate from the pilot.

Plutonium inventories for stabilization and stabilized materials

Energy Technology Data Exchange (ETDEWEB)

Williams, A.K.

1996-05-01

The objective of the breakout session was to identify characteristics of materials containing plutonium, the need to stabilize these materials for storage, and plans to accomplish the stabilization activities. All current stabilization activities are driven by the Defense Nuclear Facilities Safety Board Recommendation 94-1 (May 26, 1994) and by the recently completed Plutonium ES&H Vulnerability Assessment (DOE-EH-0415). The Implementation Plan for accomplishing stabilization of plutonium-bearing residues in response to the Recommendation and the Assessment was published by DOE on February 28, 1995. This Implementation Plan (IP) commits to stabilizing problem materials within 3 years, and stabilizing all other materials within 8 years. The IP identifies approximately 20 metric tons of plutonium requiring stabilization and/or repackaging. A further breakdown shows this material to consist of 8.5 metric tons of plutonium metal and alloys, 5.5 metric tons of plutonium as oxide, and 6 metric tons of plutonium as residues. Stabilization of the metal and oxide categories containing greater than 50 weight percent plutonium is covered by DOE Standard {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides{close_quotes} December, 1994 (DOE-STD-3013-94). This standard establishes criteria for safe storage of stabilized plutonium metals and oxides for up to 50 years. Each of the DOE sites and contractors with large plutonium inventories has either started or is preparing to start stabilization activities to meet these criteria.

Aespoe HRL - Geoscientific evaluation 1997/3. Results from pre-investigation and detailed site characterization. Comparison of predictions and observations. Geology and mechanical stability

International Nuclear Information System (INIS)

Stanfors, R.; Olsson, Paer; Stille, H.

1997-05-01

Prior to excavation of the laboratory in 1990 predictions were made for the excavation phase. The predictions concern five key issues: Geology, groundwater flow, groundwater chemistry, transport of solutes, and mechanical stability. Comparisons between predictions and observations were made during excavation in order to verify the reliability of the pre-investigations. This report presents a comparison between the geological and mechanical stability predictions and observations and an evaluation of data and investigation methods used for the 700-2874 m section of the tunnel. The report is specially highlighting the following conclusions: It is possible to localize major fracture zones during the pre-investigation at shallow (<200 m) depths; A number of minor fracture zones striking NNW-NNE were predicted to be hydraulically important and penetrate the southern area. A number of narrow fracture zone indications - 0.1-1 m wide - striking WNW-NE were mapped in the tunnel and pre-grouted sections confirm hydraulic conductors; It has not been possible to confirm the gently dipping zone EW-5, which was predicted as 'possible', with data from the tunnel; Predictions of the amount of different rock types were generally reliable as regards the major rocks, but the prediction of the distribution in space were poor as regards the minor rock types; The prediction of rock stress orientation corresponds well to the outcome; The prediction of rock quality for the tunnel, while applying the RMR-system, shows good correspondence to the observations made in the tunnel

Sea surface stability parameters

International Nuclear Information System (INIS)

Weber, A.H.; Suich, J.E.

1978-01-01

A number of studies dealing with climatology of the Northwest Atlantic Ocean have been published in the last ten years. These published studies have dealt with directly measured meteorological parameters, e.g., wind speed, temperature, etc. This information has been useful because of the increased focus on the near coastal zone where man's activities are increasing in magnitude and scope, e.g., offshore power plants, petroleum production, and the subsequent environmental impacts of these activities. Atmospheric transport of passive or nonpassive material is significantly influenced by the turbulence structure of the atmosphere in the region of the atmosphere-ocean interface. This research entails identification of the suitability of standard atmospheric stability parameters which can be used to determine turbulence structure; the calculation of these parameters for the near-shore and continental shelf regions of the U.S. east coast from Cape Hatteras to Miami, Florida; and the preparation of a climatology of these parameters. In addition, a climatology for average surface stress for the same geographical region is being prepared

78 FR 54588 - Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound

Science.gov (United States)

2013-09-05

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket No. USCG-2012-0087] Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound AGENCY: Coast Guard, DHS... Security Zone in Commencement Bay, Tacoma, Washington from 6:00 a.m. on September 2, 2013 through 11:59 p.m...

78 FR 57485 - Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound

Science.gov (United States)

2013-09-19

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket No. USCG-2012-0087] Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound AGENCY: Coast Guard, DHS... Security Zone in Commencement Bay, Tacoma, Washington from 6 a.m. on September 12, 2013 through 11:59 p.m...

Global correlations between maximum magnitudes of subduction zone interface thrust earthquakes and physical parameters of subduction zones

NARCIS (Netherlands)

Schellart, W. P.; Rawlinson, N.

2013-01-01

The maximum earthquake magnitude recorded for subduction zone plate boundaries varies considerably on Earth, with some subduction zone segments producing giant subduction zone thrust earthquakes (e.g. Chile, Alaska, Sumatra-Andaman, Japan) and others producing relatively small earthquakes (e.g.

A broader classification of damage zones

Science.gov (United States)

Peacock, D. C. P.; Dimmen, V.; Rotevatn, A.; Sanderson, D. J.

2017-09-01

Damage zones have previously been classified in terms of their positions at fault tips, walls or areas of linkage, with the latter being described in terms of sub-parallel and synchronously active faults. We broaden the idea of linkage to include structures around the intersections of non-parallel and/or non-synchronous faults. These interaction damage zones can be divided into approaching damage zones, where the faults kinematically interact but are not physically connected, and intersection damage zones, where the faults either abut or cross-cut. The damage zone concept is applied to other settings in which strain or displacement variations are taken up by a range of structures, such as at fault bends. It is recommended that a prefix can be added to a wide range of damage zones, to describe the locations in which they formed, e.g., approaching, intersection and fault bend damage zone. Such interpretations are commonly based on limited knowledge of the 3D geometries of the structures, such as from exposure surfaces, and there may be spatial variations. For example, approaching faults and related damage seen in outcrop may be intersecting elsewhere on the fault planes. Dilation in intersection damage zones can represent narrow and localised channels for fluid flow, and such dilation can be influenced by post-faulting stress patterns.

33 CFR 2.30 - Exclusive Economic Zone.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Exclusive Economic Zone. 2.30... JURISDICTION Jurisdictional Terms § 2.30 Exclusive Economic Zone. (a) With respect to the United States... States exercises sovereignty, exclusive economic zone means the zone seaward of and adjacent to the...

The formation of the economic mechanism of stabilization of enterprise’s activity

Directory of Open Access Journals (Sweden)

L. A. Zaporozhtseva

2018-01-01

Full Text Available The authors bring the research of regularities of enterprise’s economic development; bring the research of change sequence of life cycle stages in the article. There is established that a stage of maturity not always gives way to decline stage and in the next to crisis stage. Life processes of "ageing" of the enterprise can be successfully resisted. It is proved that the stage of maturity of the enterprise is associated with a "crisis of stability". Getting into the stages of recession, growth or maintaining stability becomes the way out of the crisis. The authors prove that there are such zones of staying on the life cycle’s curve in the practice of commercial organizations functioning when it is necessary to use the mechanism of stabilization (at detection of "crisis of stability", at transfer from the stage of maturity to the stage of recession and at diagnostics of hit to the stage of recession. In this regard the authors elaborate an economic mechanism for stabilization of the enterprise’s activity as a system of measures aimed at maintaining the achieved financial balance of the enterprise in a long period, which includes the following blocks: information support of the assessment of financial condition; assessment of the level of payment, business and capital stability of the enterprise; determination of the stage of the enterprise’s life cycle; characteristics of the applicable strategy; the need to use the tools for adjust the strategy to stabilize the enterprise’s activity and evaluate the results. At the same time, it is important to focus on maintaining achievable growth rates through the using of special management decisions, along with monitoring the life cycle and controlling the financial condition of the enterprise. The introduction of the economic stabilization mechanism in the enterprise’s activity jointly with the existing organizational and economic mechanism will correct the elements of the basic mechanism and

Realization of the Zone Length Measurement during Zone Refining Process via Implementation of an Infrared Camera

Directory of Open Access Journals (Sweden)

Danilo C. Curtolo

2018-05-01

Full Text Available Zone refining, as the currently most common industrial process to attain ultrapure metals, is influenced by a variety of factors. One of these parameters, the so-called “zone length”, affects not only the ultimate concentration distribution of impurities, but also the rate at which this distribution is approached. This important parameter has however neither been investigated experimentally, nor ever varied for the purpose of optimization. This lack of detections may be due to the difficult temperature measurement of a moving molten area in a vacuum system, of which the zone refining methodology is comprised. Up to now, numerical simulation as a combination of complex mathematical calculations, as well as many assumptions has been the only way to reveal it. This paper aims to propose an experimental method to accurately measure the molten zone length and to extract helpful information on the thermal gradient, temperature profile and real growth rate in the zone refining of an exemplary metal, in this case aluminum. This thermographic method is based on the measurement of the molten surface temperature via an infrared camera, as well as further data analysis through the mathematical software MATLAB. The obtained results show great correlation with the visual observations of zone length and provide helpful information to determine the thermal gradient and real growth rate during the whole process. The investigations in this paper approved the application of an infrared camera for this purpose as a promising technique to automatically control the zone length during a zone refining process.

VT Data - Zoning 20070306, Marlboro

Data.gov (United States)

Vermont Center for Geographic Information — Zoning districts, Marlboro, Vermont. Surface water buffer overlay is in a separate shapefile. Data were originally created by WRC in 2005. Marlboro's zoning bylaw...

Reductive dechlorination of trichloroethene DNAPL source zones: source zone architecture versus electron donor availability

Science.gov (United States)

Krol, M.; Kokkinaki, A.; Sleep, B.

2014-12-01

The persistence of dense-non-aqueous-phase liquids (DNAPLs) in the subsurface has led practitioners and regulatory agencies to turn towards low-maintenance, low-cost remediation methods. Biological degradation has been suggested as a possible solution, based on the well-proven ability of certain microbial species to break down dissolved chlorinated ethenes under favorable conditions. However, the biodegradation of pure phase chlorinated ethenes is subject to additional constraints: the continuous release of electron acceptor at a rate governed by mass transfer kinetics, and the temporal and spatial heterogeneity of DNAPL source zones which leads to spatially and temporally variable availability of the reactants for reductive dechlorination. In this work, we investigate the relationship between various DNAPL source zone characteristics and reaction kinetics using COMPSIM, a multiphase groundwater model that considers non-equilibrium mass transfer and Monod-type kinetics for reductive dechlorination. Numerical simulations are performed for simple, homogeneous trichloroethene DNAPL source zones to demonstrate the effect of single source zone characteristics, as well as for larger, more realistic heterogeneous source zones. It is shown that source zone size, and mass transfer kinetics may have a decisive effect on the predicted bio-enhancement. Finally, we evaluate the performance of DNAPL bioremediation for realistic, thermodynamically constrained, concentrations of electron donor. Our results indicate that the latter may be the most important limitation for the success of DNAPL bioremediation, leading to reduced bio-enhancement and, in many cases, comparable performance with water flooding.

Multichannel imager for littoral zone characterization

Science.gov (United States)

Podobna, Yuliya; Schoonmaker, Jon; Dirbas, Joe; Sofianos, James; Boucher, Cynthia; Gilbert, Gary

2010-04-01

This paper describes an approach to utilize a multi-channel, multi-spectral electro-optic (EO) system for littoral zone characterization. Advanced Coherent Technologies, LLC (ACT) presents their EO sensor systems for the surf zone environmental assessment and potential surf zone target detection. Specifically, an approach is presented to determine a Surf Zone Index (SZI) from the multi-spectral EO sensor system. SZI provides a single quantitative value of the surf zone conditions delivering an immediate understanding of the area and an assessment as to how well an airborne optical system might perform in a mine countermeasures (MCM) operation. Utilizing consecutive frames of SZI images, ACT is able to measure variability over time. A surf zone nomograph, which incorporates targets, sensor, and environmental data, including the SZI to determine the environmental impact on system performance, is reviewed in this work. ACT's electro-optical multi-channel, multi-spectral imaging system and test results are presented and discussed.

The fracture zone project - final report

International Nuclear Information System (INIS)

Andersson, Peter

1993-09-01

This report summarizes the work and the experiences gained during the fracture zone project at the Finnsjoen study site. The project is probably the biggest effort, so far, to characterize a major fracture zone in crystalline bedrock. The project was running between 1984-1990 involving a large number of geological, geohydrological, geochemical, and geomechanical investigation. The methods used for identification and characterization are reviewed and discussed in terms of applicability and possible improvements for future investigations. The discussion is exemplified with results from the investigation within the project. Flow and transport properties of the zone determined from hydraulic tests and tracer tests are discussed. A large number of numerical modelling efforts performed within the fracture zone project, the INTRAVAL project, and the SKB91-study are summarized and reviewed. Finally, occurrence of similar zones and the relevance of major low angle fracture zones in connection to the siting of an underground repository is addressed

Chemical stabilization of metals and arsenic in contaminated soils using oxides--a review.

Science.gov (United States)

Komárek, Michael; Vaněk, Aleš; Ettler, Vojtěch

2013-01-01

Oxides and their precursors have been extensively studied, either singly or in combination with other amendments promoting sorption, for in situ stabilization of metals and As in contaminated soils. This remediation option aims at reducing the available fraction of metal(loid)s, notably in the root zone, and thus lowering the risks associated with their leaching, ecotoxicity, plant uptake and human exposure. This review summarizes literature data on mechanisms involved in the immobilization process and presents results from laboratory and field experiments, including the subsequent influence on higher plants and aided phytostabilization. Despite the partial successes in the field, recent knowledge highlights the importance of long-term and large-scale field studies evaluating the stability of the oxide-based amendments in the treated soils and their efficiency in the long-term. Copyright © 2012 Elsevier Ltd. All rights reserved.

Modelling of diamagnetic stabilization of ideal MHD eigenmodes associated with the transport barrier

International Nuclear Information System (INIS)

Huysmans, G.; Sharapov, S.; Mikhailovskii, A.; Kerner, W.

2001-01-01

A new code, MISHKA-D (Drift MHD), has been developed as an extension of the ideal MHD code MISHKA-1 in order to investigate the finite gyroradius stabilizing effect of ion diamagnetic drift frequency, ω *i , on linear ideal MHD eigenmodes in tokamaks with shaped plasma cross-section. The MISHKA-D code gives a self-consistent computation of both stable and unstable eigenmodes with eigenvalues [γ] ≅ ω *i in plasmas with strong radial variation in the ion diamagnetic frequency. Test results of the MISHKA-D code show good agreement with the analytically obtained ω *i -spectrum and stability limits of the internal kink mode, n/m=1/1, used as a benchmark case. Finite-n ballooning and low-n kink (peeling) modes in the edge transport barrier just inside the separatrix are studied for H-mode plasma with the ω *i -effect included. The ion diamagnetic stabilization of the ballooning modes is found to be most effective for narrow edge pedestals. For low enough plasma density the ω *i - stabilization can lead to a second zone of ballooning stability, in which all the ballooning modes are stable for any value of the pressure gradient. For internal transport barriers typical of JET optimised shear discharges, the stabilizing influence of ion diamagnetic frequency on the n=1 global pressure driven disruptive mode is studied. A strong radial variation of ω *i is found to significantly decrease the stabilizing ω *i - effect on the n=1 mode, in comparison with the case of constant ω *i estimated at the foot of the internal transport barrier. (author)

Flow Hydrodynamics across Open Channel Flows with Riparian Zones: Implications for Riverbank Stability

Directory of Open Access Journals (Sweden)

Da Liu

2017-09-01

Full Text Available Riverbank vegetation is of high importance both for preserving the form (morphology and function (ecology of natural river systems. Revegetation of riverbanks is commonly used as a means of stream rehabilitation and management of bank instability and erosion. In this experimental study, the effect of different riverbank vegetation densities on flow hydrodynamics across the channel, including the riparian zone, are reported and discussed. The configuration of vegetation elements follows either linear or staggered arrangements as vegetation density is progressively increased, within a representative range of vegetation densities found in nature. Hydrodynamic measurements including mean streamwise velocity and turbulent intensity flow profiles are recorded via acoustic Doppler velocimetry (ADV—both at the main channel and within the riverbank. These results show that for the main channel and the toe of riverbank, turbulence intensity for the low densities (λ ≈ 0 to 0.12 m−1 can increase up to 40% compared the case of high densities (λ = 0.94 to 1.9 m−1. Further analysis of these data allowed the estimation of bed-shear stresses, demonstrating 86% and 71% increase at the main channel and near the toe region, for increasing densities (λ = 0 to 1.9 m−1. Quantifying these hydrodynamic effects is important for assessing the contribution of physically representative ranges of riparian vegetation densities on hydrogeomorphologic feedback.

Autogenous bone grafts in the esthetic zone: optimizing the procedure using piezosurgery.

Science.gov (United States)

Majewski, Piotr

2012-12-01

Soft and hard tissue defects pose a therapeutic challenge in modern implant dentistry. There are a multitude of surgical techniques available, and it is necessary to match the problem with the solution. This report describes the reconstruction of the alveolar ridge in the esthetic zone with the help of autogenous bone blocks harvested from the chin that were shaped to fit and stabilized at the recipient site. The procedures were performed using Piezosurgery, which made it possible to introduce surgical modifications and had a significant impact on the accuracy of the procedure. An observation period of 2 to 7 years showed positive stable results for treatment in terms of function and esthetics.

Fault system and thermal regime in the vicinity of site NGHP-01-10, Krishna-Godavari basin, Bay of Bengal

Digital Repository Service at National Institute of Oceanography (India)

Dewangan, P.; Srirama, G.; Ramprasad, T.; Ramana, M.V.; Jaiswal, P.

driven (Milkov and Sassen, 2002). In structural accumulation gases are transported to the GHSZ through features such as faults and mud 3 volcanoes, e.g. northwestern Gulf of Mexico (Brooks et al., 1986; MacDonald et al., 1994; Milkov and Sassen, 2000... horizons, e.g., Blake ridge (Xu and Ruppel, 1999; Dickens et al., 1997), Gulf of Mexico minibasins (Milkov and Sassen, 2001; Pflaum et al., 1986), Nankai trough (Matsumoto et al., 2001), and Mallik (Dallimore et al., 1999). A combination of both...

Do "Some" Enterprise Zones Create Jobs?

Science.gov (United States)

Kolko, Jed; Neumark, David

2010-01-01

We study how the employment effects of enterprise zones vary with their location, implementation, and administration, based on evidence from California. We use new establishment-level data and geographic mapping methods, coupled with a survey of enterprise zone administrators. Overall, the evidence indicates that enterprise zones do not increase…

SEMIAUTOMATIC DETECTION OF TUMORAL ZONE

Directory of Open Access Journals (Sweden)

Ezzeddine Zagrouba

2011-05-01

Full Text Available This paper describes a robust method based on the cooperation of fuzzy classification and regions segmentation algorithms, in order to detect the tumoral zone in the brain Magnetic Resonance Imaging (MRI. On one hand, the classification in fuzzy sets is done by the Fuzzy C-Means algorithm (FCM, where a study of its different parameters and its complexity has been previously realised, which led us to improve it. On the other hand, the segmentation in regions is obtained by an hierarchical method through adaptive thresholding. Then, an operator expert selects a germ in the tumoral zone, and the class containing the sick zone is localised in return for the FCM algorithm. Finally, the superposition of the two partitions of the image will determine the sick zone. The originality of our approach is the parallel exploitation of different types of information in the image by the cooperation of two complementary approaches. This allows us to carry out a pertinent approach for the detection of sick zone in MRI images.

Splenic marginal zone lymphoma.

Science.gov (United States)

Piris, Miguel A; Onaindía, Arantza; Mollejo, Manuela

Splenic marginal zone lymphoma (SMZL) is an indolent small B-cell lymphoma involving the spleen and bone marrow characterized by a micronodular tumoral infiltration that replaces the preexisting lymphoid follicles and shows marginal zone differentiation as a distinctive finding. SMZL cases are characterized by prominent splenomegaly and bone marrow and peripheral blood infiltration. Cells in peripheral blood show a villous cytology. Bone marrow and peripheral blood characteristic features usually allow a diagnosis of SMZL to be performed. Mutational spectrum of SMZL identifies specific findings, such as 7q loss and NOTCH2 and KLF2 mutations, both genes related with marginal zone differentiation. There is a striking clinical variability in SMZL cases, dependent of the tumoral load and performance status. Specific molecular markers such as 7q loss, p53 loss/mutation, NOTCH2 and KLF2 mutations have been found to be associated with the clinical variability. Distinction from Monoclonal B-cell lymphocytosis with marginal zone phenotype is still an open issue that requires identification of precise and specific thresholds with clinical meaning. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cornell Mixing Zone Expert System

Science.gov (United States)

This page provides an overview Cornell Mixing Zone Expert System water quality modeling and decision support system designed for environmental impact assessment of mixing zones resulting from wastewater discharge from point sources

Drug-Free School Zones: Taking Charge.

Science.gov (United States)

Thomas, Carol F.

Information for planning and implementing drug-free school zones within a broader school-community prevention and intervention program is provided in this guidebook. The first section provides background information on drug-free school zone legislation and common elements of drug-free school zones. The risk and protective factors for alcohol and…

State Enterprise Zone Programs: Have They Worked?

Science.gov (United States)

Peters, Alan H.; Fisher, Peter S.

The effectiveness of state enterprise zone programs was examined by using a hypothetical-firm model called the Tax and Incentives Model-Enterprise Zones (TAIM-ez) model to analyze the value of enterprise zone incentives to businesses across the United States and especially in the 13 states that had substantial enterprise zone programs by 1990. The…

Dead zone characteristics of a gas counter

International Nuclear Information System (INIS)

Nohtomi, Akihiro; Sakae, Takeji; Matoba, Masaru; Koori, Norihiko.

1990-01-01

The dead zone was recently defined as the product of dead length and dead time in order to describe the characteristics of the self-quenching streamer (SQS) mode of a gas counter. Investigation of the dead zone characteristics has been extended for the proportional and GM modes, and the measured dead zone has been compared with that of the SQS mode. Accurate values for the dead zone could be determined by means of a newly developed method with a pulse interval time to amplitude converter. Each operation mode indicates distinct dead zone characteristics. Properties of gas counters for high counting rates may be improved on the basis of measurements of the dead zone. (author)

Using SST and land cover data from EO Missions for improved mesoscale modelling of the coastal zone

DEFF Research Database (Denmark)

Karagali, Ioanna; Floors, Rogier Ralph; Lea, Guillaume

was to evaluate the uncertainty of the modelled wind in the coastal zone and further improve it. Moreover LIDAR measurements were used to evaluate the wind speed retrieval from high resolution SAR systems (Sentinel-1 and TerraSAR-X). The WRF model used a high-resolution satellite SST reanalysis product from...... be implemented in the meso-scale model to better represent the actual conditions in the study area. Such improvements are expected to strengthen the model’s ability to represent land- sea and air-sea interactions, the atmospheric stability and the local topographic features that partly affect the coastal zone......Existing wind measurements in near-shore and offshore areas are sparse and scarce, therefore simulations from state-of-the-art meso-scale models are used for wind resource predictions. In coastal and near-shore areas, models are inaccurate and uncertain, mainly because of numerical approximations...

Street Prostitution Zones and Crime

OpenAIRE

Bisschop, Paul; Kastoryano, Stephen; van der Klaauw, Bas

2015-01-01

This paper studies the effects of introducing legal street prostitution zones on both registered and perceived crime. We exploit a unique setting in the Netherlands where legal street prostitution zones were opened in nine cities under different regulation systems. We provide evidence that the opening of these zones was not in response to changes in crime. Our difference-in-difference analysis using data on the largest 25 Dutch cities between 1994 and 2011 shows that opening a legal street pr...

76 FR 3014 - Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound, WA

Science.gov (United States)

2011-01-19

... Coast Guard will enforce the Blair Waterway security zone in Commencement Bay, WA for protection of... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket No. USCG-2011-0015] Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound, WA AGENCY: Coast Guard, DHS...

Simultaneous use of two prostaglandin radioimmunoassays employing two antisera of differing specificity. II. Relative stability of prostaglandins E1, E2, and F1alpha in cell cultures of BALB/c 3T3 and SV3T3 mouse fibroblasts

International Nuclear Information System (INIS)

Ritzi, E.M.; Stylos, W.A.

1976-01-01

The relative stability of Prostaglandins (PGs) E1, E2 and F1α in cultures of BALB/c 3T3 and SV3T3 cells has been evaluated using 3 different approaches. First, total recovery of tritium in the ethyl acetate phase following incubation and extraction of PGF1α and PGE1 demonstrated greater stability for PGF1α (88.8 percent) than PGE1 (65.9 percent). Second, analysis of incubated, extracted, tritiated PGs by thin layer chromatography revealed decreases of up to 23 percent in the PGE zone following incubation of 3H-PGE1. With increasing time of incubation, decreases in the PGE zone were accompanied by increase in PGA-like compounds. 3H-PGF1α demonstrated greater stability, having greater than 90 percent recovery of the tritium in the PGF zone. A third approach to the assessment of PG stability in culture was the comparison of the production of individual PGs by radioimmunoassay (RIA). The data obtained by RIA indicated a lag in the increase of PGA and PGB, until an initial rise in PGE was noted, suggesting that PGA and PGB may be secondary products arising from PGE which exhibits only partial stability in culture. By employing two RIAs, one for total PGE and one for PGA and PGB, the composite determination PG [E + (A + B)] can be used to provide a more meaningful determination of PG production because of the instability of the PGs. On the other hand, individual determinations are helpful in assessing the stability of PGEs in cell cultures

Radiation danger of exclusion zone objects

International Nuclear Information System (INIS)

Kholosha, V.I.; Proskura, N.I.; Ivanov, Yu.A.; Kazakov, S.V.; Arkhipov, A.N.

2001-01-01

The analysis of radiation danger of the Exclusion Zone objects was made. Here, the Zone is defined as the territory from which the population has been evacuated in 1986 owing to the Chernobyl accident and possible outflow of the contaminated substances out of the borders is potentially dangerous to the Ukraine. In the present work were analyzed such problems as sources of radiation danger in the Zone, ways of radionuclide migration out of the borders of the Zone in normal and emergency situations, the non-radiation (ecological) danger factors of the Zone objects, doses (individual and collective) from various sources and on separate ways of their formation, and the characteristics of radiation danger of the Zone objects. The conclusions are: (1) Radionuclide flows both from technologic and natural sources exceed those from Shelter objects, (2) Under emergency conditions, radionuclide flows and doze loading remain comparable with those from emergency sources, (3) To solve some management tasks in radiation situation, the basic works on the Shelter objects should be oriented to decrease probability of emergency occurrence and to reduce radiation influence (prevention wash-outs during high waters, fire-prevention measures in forests and strengthening of the control behind non-authorized use of objects in the Zone). (S. Ohno)

76 FR 9646 - Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation...

Science.gov (United States)

2011-02-22

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Parts 100, 117, 147, and 165 [USCG-2010-0399] Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation Regulations and Regulated Navigation Areas AGENCY: Coast Guard, DHS. ACTION: Notice of expired temporary rules...

Tracing the influence of the Trans-European Suture Zone into the mantle transition zone

Czech Academy of Sciences Publication Activity Database

Knapmeyer-Endrun, B.; Krüger, F.; Legendre, C. P.; Geissler, W.H.; Plomerová, Jaroslava; Babuška, Vladislav; Gaždová, Renata; Jedlička, Petr; Kolínský, Petr; Málek, Jiří; Novotný, Oldřich; Růžek, Bohuslav

2013-01-01

Roč. 363, FEB 1 (2013), s. 73-87 ISSN 0012-821X Institutional support: RVO:67985530 ; RVO:67985891 Keywords : mantle transition zone * Trans-European Suture Zone * East European Craton Subject RIV: DC - Siesmology, Volcanology, Earth Structure Impact factor: 4.724, year: 2013

VT Data - Zoning Stream Buffers 20081014, Hartford

Data.gov (United States)

Vermont Center for Geographic Information — OVERLAY DISTRICT. Models a municipality’s zoning zones and related information. Final boundary determinations must be obtained from the town Zoning Administrator....

GAMMA RAYS FROM THE TYCHO SUPERNOVA REMNANT: MULTI-ZONE VERSUS SINGLE-ZONE MODELING

Energy Technology Data Exchange (ETDEWEB)

Atoyan, Armen [Department of Mathematics, Concordia University, 1455 de Maisonneuve Blvd. West, Montreal, Quebec H3G 1M8 (Canada); Dermer, Charles D., E-mail: atoyan@mathstat.concordia.ca, E-mail: charles.dermer@nrl.navy.mil [Code 7653, Naval Research Laboratory, Washington, DC 20375-5352 (United States)

2012-04-20

Recent Fermi and VERITAS observations of the prototypical Type Ia supernova remnant (SNR) Tycho have discovered {gamma}-rays with energies E in the range 0.4 GeV {approx}< E {approx}< 10 TeV. Crucial for the theory of Galactic cosmic-ray origin is whether the {gamma}-rays from SNRs are produced by accelerated hadrons (protons and ions) or by relativistic electrons. Here we show that strong constraints on the leptonic model imposed in the framework of the commonly used single-zone model are essentially removed if the analysis of the broadband radiation spectrum of Tycho is done in the two-zone (or, in general, multi-zone) approach, which is likely to apply to every SNR. Importantly, we show that the single-zone approach may underpredict the {gamma}-ray fluxes by an order of magnitude. A hadronic model can, however, also fit the detected {gamma}-ray spectrum. The difference between {gamma}-ray fluxes of hadronic and leptonic origins becomes significant only at {approx}<300 MeV, which could be revealed by spectral measurements of Tycho and other SNRs at these energies.

Chaotic Zones around Rotating Small Bodies

Energy Technology Data Exchange (ETDEWEB)

Lages, José; Shevchenko, Ivan I. [Institut UTINAM, Observatoire des Sciences de l’Univers THETA, CNRS, Université de Franche-Comté, Besançon F-25030 (France); Shepelyansky, Dima L., E-mail: jose.lages@utinam.cnrs.fr [Laboratoire de Physique Théorique du CNRS, IRSAMC, Université de Toulouse, UPS, Toulouse F-31062 (France)

2017-06-01

Small bodies of the solar system, like asteroids, trans-Neptunian objects, cometary nuclei, and planetary satellites, with diameters smaller than 1000 km usually have irregular shapes, often resembling dumb-bells or contact binaries. The spinning of such a gravitating dumb-bell creates around it a zone of chaotic orbits. We determine its extent analytically and numerically. We find that the chaotic zone swells significantly if the rotation rate is decreased; in particular, the zone swells more than twice if the rotation rate is decreased 10 times with respect to the “centrifugal breakup” threshold. We illustrate the properties of the chaotic orbital zones in examples of the global orbital dynamics about asteroid 243 Ida (which has a moon, Dactyl, orbiting near the edge of the chaotic zone) and asteroid 25143 Itokawa.

76 FR 55566 - Safety Zones; Fireworks Displays and Surfing Events in Captain of the Port Long Island Sound Zone

Science.gov (United States)

2011-09-08

...-AA00 Safety Zones; Fireworks Displays and Surfing Events in Captain of the Port Long Island Sound Zone... zones for marine events within the Captain of the Port (COTP) Long Island Sound Zone for a surfing event... unless authorized by the COTP Sector Long Island Sound. DATES: This rule is effective in the CFR on...

Light-zone(s: as Concept and Tool

Directory of Open Access Journals (Sweden)

Merete Madsen

2012-11-01

Full Text Available Daylight is essential to the experience of an architectural space. Nevertheless, amongst the handful of predominantly scientific methods available to assess daylight in architecture, there are only a few considering the spatial and form-giving characteristics of daylight. This paper investigates light-zone(s as concept and tool, which can be taken as a point of departure for a new method to perceive, consider and analyse daylight in architecture. As concept, light-zone(s are areas, fields or zones of light. It is a way of considering a space’s daylight as (forms of bubbles or spheres of light, which as light-zones can be compressed, expanded, combined, exploded, etc., all according to the character of 'the meeting' between the light-zone(s and the space itself (inclusive of the space’scontent. Thus, the daylight in a space can be regarded asa composition of light-zones.As tool, light-zone(s are (spatial groupings of the lightingvariables (intensity, direction, distribution and colour, whichare significant to the space and form-giving characteristicsof light. That is to say, the light-zone(s tool is the point ofdeparture for a method of creating a spatial ‘grasp’ on daylighting variables in a given space. The relation between the light-zone(s concept and tool respectively can be described as follows: On the one level light-zone(s can be explored as an architectural idea or notion, thus belonging more to the field of architectural theory. On another more practice-driven level, light-zone(s can be articulated and specified in relation to lighting technology.

Quantifying the Variation in Shear Zone Character with Depth: a Case Study from the Simplon Shear Zone, Central Alps

Science.gov (United States)

Cawood, T. K.; Platt, J. P.

2017-12-01

A widely-accepted model for the rheology of crustal-scale shear zones states that they comprise distributed strain at depth, in wide, high-temperature shear zones, which narrow to more localized, high-strain zones at lower temperature and shallower crustal levels. We test and quantify this model by investigating how the width, stress, temperature and deformation mechanisms change with depth in the Simplon Shear Zone (SSZ). The SSZ marks a major tectonic boundary in the central Alps, where normal-sense motion and rapid exhumation of the footwall have preserved evidence of older, deeper deformation in rocks progressively further into the currently-exposed footwall. As such, microstructures further from the brittle fault (which represents the most localized, most recently-active part of the SSZ) represent earlier, higher- temperature deformation from deeper crustal levels, while rocks closer to the fault have been overprinted by successively later, cooler deformation at shallower depths. This study uses field mapping and microstructural studies to identify zones representing deformation at various crustal levels, and characterize each in terms of zone width (representing width of the shear zone at that time and depth) and dominant deformation mechanism. In addition, quartz- (by Electron Backscatter Diffraction, EBSD) and feldspar grain size (measured optically) piezometry are used to calculate the flow stress for each zone, while the Ti-in-quartz thermometer (TitaniQ) is used to calculate the corresponding temperature of deformation. We document the presence of a broad zone in which quartz is recrystallized by the Grain Boundary Migration (GBM) mechanism and feldspar by Subgrain Rotation (SGR), which represents the broad, deep zone of deformation occurring at relatively high temperatures and low stresses. In map view, this transitions to successively narrower zones, respectively characterized by quartz SGR and feldspar Bulge Nucleation (BLG); quartz BLG and brittle

Empowerment Zones and Enterprise Districts - Volusia County Enterprise Zones

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Florida's Enterprise Zone Program encourages economic growth and investment in distressed areas by offering tax advantages and incentives to businesses that are...

78 FR 7265 - Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound, WA

Science.gov (United States)

2013-02-01

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket No. USCG-2012-0087] Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound, WA AGENCY: Coast Guard, DHS... Security Zone in Commencement Bay, Tacoma, Washington from 6 a.m. on February 1, 2013, through 11:59 p.m...

78 FR 11981 - Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound, WA

Science.gov (United States)

2013-02-21

... DEPARTMENT OF HOMELAND SECURITY Coast Guard 33 CFR Part 165 [Docket No. USCG-2012-0087] Security Zone; Protection of Military Cargo, Captain of the Port Zone Puget Sound, WA AGENCY: Coast Guard, DHS... Security Zone in Commencement Bay, Tacoma, Washington from 6 a.m. on February 23, 2013, through 11:59 p.m...

Colloid-Facilitated Transport of Radionuclides Through The Vadose Zone

International Nuclear Information System (INIS)

Markus Flury; James B. Harsh; John F. McCarthy' Peter C. Lichtner; John M. Zachara

2007-01-01

The main purpose of this project was to advance the basic scientific understanding of colloid and colloid-facilitated Cs transport of radionuclides in the vadose zone. We focused our research on the hydrological and geochemical conditions beneath the leaking waste tanks at the USDOE Hanford reservation. Specific objectives were (1) to determine the lability and thermodynamic stability of colloidal materials, which form after reacting Hanford sediments with simulated Hanford Tank Waste, (2) to characterize the interactions between colloidal particles and contaminants, i.e., Cs and Eu, (3) to determine the potential of Hanford sediments for in situ mobilization of colloids, (4) to evaluate colloid-facilitated radionuclide transport through sediments under unsaturated flow, (5) to implement colloid-facilitated contaminant transport mechanisms into a transport model, and (6) to improve conceptual characterization of colloid-contaminant-soil interactions and colloid-facilitated transport for clean-up procedures and long-term risk assessment

Automatic detection and classification of damage zone(s) for incorporating in digital image correlation technique

Science.gov (United States)

Bhattacharjee, Sudipta; Deb, Debasis

2016-07-01

Digital image correlation (DIC) is a technique developed for monitoring surface deformation/displacement of an object under loading conditions. This method is further refined to make it capable of handling discontinuities on the surface of the sample. A damage zone is referred to a surface area fractured and opened in due course of loading. In this study, an algorithm is presented to automatically detect multiple damage zones in deformed image. The algorithm identifies the pixels located inside these zones and eliminate them from FEM-DIC processes. The proposed algorithm is successfully implemented on several damaged samples to estimate displacement fields of an object under loading conditions. This study shows that displacement fields represent the damage conditions reasonably well as compared to regular FEM-DIC technique without considering the damage zones.

Characteristics of a paleosol and its implication for the Critical Zone development, Rocky Mountain Front Range of Colorado, USA

Energy Technology Data Exchange (ETDEWEB)

Leopold, Matthias, E-mail: leopold@wzw.tum.de [Geomorphology and Soil Science, Technische Universitaet Muenchen, D-85354 Freising-Weihenstephan (Germany); Voelkel, Joerg [Geomorphology and Soil Science, Technische Universitaet Muenchen, D-85354 Freising-Weihenstephan (Germany); Dethier, David [Williams College, Dept. Geoscience, Williamstown, MA 01267 (United States); Huber, Juliane [Geomorphology and Soil Science, Technische Universitaet Muenchen, D-85354 Freising-Weihenstephan (Germany); Steffens, Markus [Soil Science, Technische Universitaet Muenchen, D-85354 Freising-Weihenstephan (Germany)

2011-06-15

Highlights: > We dated a sediment section (USA) including an 8000 years old paleosol by OSL and Radiocarbon. > Nuclear magnetic resonance spectroscopy is used to characterize the paleosols' organic matter. > High amounts of aromatic structures (charcoal) indicate fire events that influenced the soil. > The section represents geomorphic stability and instability phases. > We use these geomorphic changes to reconstruct the Critical Zone development. - Abstract: Activity and stability phases as well as geomorphic processes within the Critical Zone are well known. Erosion and deposition of sediments represent activity; soils represent geomorphic stability phases. Data are presented from a 4 m deep sediment section that was dated by luminescence techniques. Upslope erosion and resulting sedimentation started in the late Pleistocene around 18 ka until 12 ka. Conditions at the study site then changed, which led to the formation of a well-developed soil. Radiocarbon dating of the organic matter yielded ages between 8552 and 8995 cal. BP. From roughly 6.2 to 5.4 ka another activity phase accompanied by according sediment deposition buried the soil and a new soil, a Cambisol, was formed at the surface. The buried soil is a strongly developed Luvisol. The black colors in the upper part of the buried soil are not the result of pedogenic accumulation of normal organic matter within an A-horizon. Nuclear magnetic resonance spectroscopy clearly documents the high amount of aromatic components (charcoal), which is responsible for the dark color. This indicates severe burning events at the site and the smaller charcoal dust (black carbon) was transported to deeper parts of the profile during the process of clay translocation.

Characteristics of a paleosol and its implication for the Critical Zone development, Rocky Mountain Front Range of Colorado, USA

International Nuclear Information System (INIS)

Leopold, Matthias; Voelkel, Joerg; Dethier, David; Huber, Juliane; Steffens, Markus

2011-01-01

Highlights: → We dated a sediment section (USA) including an 8000 years old paleosol by OSL and Radiocarbon. → Nuclear magnetic resonance spectroscopy is used to characterize the paleosols' organic matter. → High amounts of aromatic structures (charcoal) indicate fire events that influenced the soil. → The section represents geomorphic stability and instability phases. → We use these geomorphic changes to reconstruct the Critical Zone development. - Abstract: Activity and stability phases as well as geomorphic processes within the Critical Zone are well known. Erosion and deposition of sediments represent activity; soils represent geomorphic stability phases. Data are presented from a 4 m deep sediment section that was dated by luminescence techniques. Upslope erosion and resulting sedimentation started in the late Pleistocene around 18 ka until 12 ka. Conditions at the study site then changed, which led to the formation of a well-developed soil. Radiocarbon dating of the organic matter yielded ages between 8552 and 8995 cal. BP. From roughly 6.2 to 5.4 ka another activity phase accompanied by according sediment deposition buried the soil and a new soil, a Cambisol, was formed at the surface. The buried soil is a strongly developed Luvisol. The black colors in the upper part of the buried soil are not the result of pedogenic accumulation of normal organic matter within an A-horizon. Nuclear magnetic resonance spectroscopy clearly documents the high amount of aromatic components (charcoal), which is responsible for the dark color. This indicates severe burning events at the site and the smaller charcoal dust (black carbon) was transported to deeper parts of the profile during the process of clay translocation.

Prediction of Ship Resonant Rolling - Related Dangerous Zones with Regard to the Equivalent Metacentric Height Governing Natural Frequency of Roll

Directory of Open Access Journals (Sweden)

Przemyslaw Krata

2017-12-01

Full Text Available Potentially dangerous zones corresponding to dynamical stability phenomena, possibly encountered by ships sailing in rough sea, are estimated nowadays with the use of the method recommended by IMO in the guidance coded MSC.1/Circ.1228. In this IMO method the parameter governing the natural period of roll is the initial metacentric height. Some earlier studies revealed that the initial metacentric height which is commonly in use on-board ships for the purpose of performing the MSC.1/Circ.1228-recommended calculations, may significantly vary from the so called equivalent metacentric height obtained for large amplitudes of ship’s roll. In the light of such ascertainment, the paper deals with resultant resonance roll zones locations with regard to the equivalent metacentric height concept remaining appropriate for large amplitudes of roll. The noteworthy transfer of the resonance zones location is disclosed which reflects the distinct configurations of potentially dangerous ship’s course and speed configurations than could be predicted on the basis the initial metacentric height.

New geometrical compactness measures for zones design

Directory of Open Access Journals (Sweden)

Eric Alfredo Rincón-García

2012-07-01

Full Text Available The design of compact zones has been studied because of its influence in the creation of zones with regular forms, which are easier to analyze, to investigate or to administer. This paper propose a new method to measure compactness,by means of the transformation of the original geographical spaces, into figures formed with square cells, which are used to measure the similarity between the original zone and an ideal zone with straight forms. The proposed method was applied to design electoral zones, which must satisfy constraints of compactness, contiguity and population balance, in a topographical configuration that favors the creation of twisted and diffuse shapes. The results show that the new method favors the creation of zones with straight forms, without an important effect to the population balance, which are considered zones of high quality. Keywords: Redistricting, compactness, simulated annealing, GIS. Mathematics Subject Classification: 90C59, 90C29, 68T20.

Trading Zones in Early Modern Europe.

Science.gov (United States)

Long, Pamela O

2015-12-01

This essay adopts the concept of trading zones first developed for the history of science by Peter Galison and redefines it for the early modern period. The term "trading zones" is used to mean arenas in which substantive and reciprocal communication occurred between individuals who were artisanally trained and learned (university-trained) individuals. Such trading zones proliferated in the sixteenth century. They tended to arise in certain kinds of places and not in others, but their existence must be determined empirically. The author's work on trading zones differs from the ideas of Edgar Zilsel, who emphasized the influence of artisans on the scientific revolution. In contrast, in this essay, the mutual influence of artisans and the learned on each other is stressed, and translation is used as a modality that was important to communication within trading zones.

Distributed Adaptive Neural Network Output Tracking of Leader-Following High-Order Stochastic Nonlinear Multiagent Systems With Unknown Dead-Zone Input.

Science.gov (United States)

Hua, Changchun; Zhang, Liuliu; Guan, Xinping

2017-01-01

This paper studies the problem of distributed output tracking consensus control for a class of high-order stochastic nonlinear multiagent systems with unknown nonlinear dead-zone under a directed graph topology. The adaptive neural networks are used to approximate the unknown nonlinear functions and a new inequality is used to deal with the completely unknown dead-zone input. Then, we design the controllers based on backstepping method and the dynamic surface control technique. It is strictly proved that the resulting closed-loop system is stable in probability in the sense of semiglobally uniform ultimate boundedness and the tracking errors between the leader and the followers approach to a small residual set based on Lyapunov stability theory. Finally, two simulation examples are presented to show the effectiveness and the advantages of the proposed techniques.

Main principles of the Chernobyl' NPP zone development

International Nuclear Information System (INIS)

Ignatenko, E.I.; Komarov, V.I.; Zverkov, V.V.; Proskuryakov, A.G.

1989-01-01

It is suggested to divide the Chernobyl' NPP zone into two parts, which are the alienation and evacuation (buffer) zones. The alienation zone includes the areas with greatest contamination around the Chernobyl' NPP. The population residence in this zone is forbidden. The watching method of working with short-time personnel residence is suggested to be used in this zone. The buffer zone is the territory out of the alienation zone boundaries including all settlements, from which the population is evacuated. Constant residence is permitted in the buffer zone for persons 50 and more years old with introduction of restrictions for diet and residence organization. The production activity in this zone includes operation of three units of the Chernobyl' NPP, works with the Ukrytie object and researches. Operations connected with radioactive waste processing and redisposal from places of storage is not recommended to be done. It is suggested to develop methods for local radioactive waste processing

Planktonic Subsidies to Surf-Zone and Intertidal Communities

Science.gov (United States)

Morgan, Steven G.; Shanks, Alan L.; MacMahan, Jamie H.; Reniers, Ad J. H. M.; Feddersen, Falk

2018-01-01

Plankton are transported onshore, providing subsidies of food and new recruits to surf-zone and intertidal communities. The transport of plankton to the surf zone is influenced by wind, wave, and tidal forcing, and whether they enter the surf zone depends on alongshore variation in surf-zone hydrodynamics caused by the interaction of breaking waves with coastal morphology. Areas with gently sloping shores and wide surf zones typically have orders-of-magnitude-higher concentrations of plankton in the surf zone and dense larval settlement in intertidal communities because of the presence of bathymetric rip currents, which are absent in areas with steep shores and narrow surf zones. These striking differences in subsidies have profound consequences; areas with greater subsidies support more productive surf-zone communities and possibly more productive rocky intertidal communities. Recognition of the importance of spatial subsidies for rocky community dynamics has recently advanced ecological theory, and incorporating surf-zone hydrodynamics would be an especially fruitful line of investigation.

Problems of Chernobyl exclusion zone

International Nuclear Information System (INIS)

1996-01-01

The collection comprises the results of researches and design activity in the ChNPP exclusion zone with the aim to develop technology, equipment and instruments for RAW management and accident clean-up, studying of the composition and structure of the activity solid bearers in the soil of the exclusion zone and transformation of the radionuclides in the nearest zone of ChNPP. Much attention is paid to medical and biological problems of the accident influence on the flora, fauna and people's health labour conditions and incidence of the people involved

Problems of Chornobyl Exclusion Zone

International Nuclear Information System (INIS)

Kashparov, V.A.

2009-01-01

The collection comprises the results of researches and design activity in the ChNPP exclusion zone with the aim to develop technology, equipment and instruments for RAW management and accident clean-up, studying of the composition and structure of the activity solid bearers in the soil of the exclusion zone and transformation of the radionuclides in the nearest zone of ChNPP. Much attention is paid to medical and biological problems of the accident influence on the flora, fauna and people's health, labour conditions and incidence of the people involved.

Numerical calculation procedure for criticality parameters of the two-zone reflected reactor with flat central zone

International Nuclear Information System (INIS)

Bosevski, T.; Strugar, P.

1966-10-01

In determining the criticality parameters of a two-zone reactor with flat central zone one encounters a numerical problem requiring the solution of a system of two non-linear equations. To solve them the Newton method, which proved convenient, was used n this work. By comparing our results with those reported one obtains about 5% smaller values of both the radius of the flat zone and of the radial buckling of the outer zone. This discrepancy probably results from some approximations used in solving the same system of equations used in solving the same system of equations where the procedure form was applied, whereas the calculation time is by one order of magnitude smaller

Nuclear weapons free zones

International Nuclear Information System (INIS)

Stahl, K.

1990-01-01

The article analyses the concept and problems of the two nuclear weapons free zones in Latin America and in the South Pacific established by the Treaty of Tlatelolco and the Treaty of Rarotonga. So far the nuclear weapons states except China have refused to sign the additional protocols of the Treaties or have signed them only with considerable provisos. Therefore they don't fully recognize the nuclear weapons free status of those zones, or they don't recognize it at all. Both Treaties contain no provisions to regulate the transit of nuclear weapons through the zones. This allows de facto the stationing of nuclear weapons in the military bases of the US which are located within the nuclear weapons free zone of Latin America. The Treaty of Tlatelolco contains also the right of the states, party to the Treaty, to explode nuclear devices for peaceful purposes. Since peaceful and military nuclear explosions cannot be distinguished technically, this right could also undermine the nuclear weapons free status of the region. Important nuclear threshold countries like Argentina and Brazil have furthermore refrained from putting the Treaty into force. (orig.) [de

Association of Stability Parameters and Yield Stability of Sesame ...

African Journals Online (AJOL)

Association of Stability Parameters and Yield Stability of Sesame ( Sesamum ... Information on phenotypic stability is useful for the selection of crop varieties as well as for ... as an alternative to parametric stability measurements is important.

Aespoe HRL - Geoscientific evaluation 1997/3. Results from pre-investigation and detailed site characterization. Comparison of predictions and observations. Geology and mechanical stability

Energy Technology Data Exchange (ETDEWEB)

Stanfors, R. [RS Consulting, Lund (Sweden); Olsson, Paer [Skanska AB Stockholm (Sweden); Stille, H. [Royal Inst. of Tech., Stockholm (Sweden)

1997-05-01

Prior to excavation of the laboratory in 1990 predictions were made for the excavation phase. The predictions concern five key issues: Geology, groundwater flow, groundwater chemistry, transport of solutes, and mechanical stability. Comparisons between predictions and observations were made during excavation in order to verify the reliability of the pre-investigations. This report presents a comparison between the geological and mechanical stability predictions and observations and an evaluation of data and investigation methods used for the 700-2874 m section of the tunnel. The report is specially highlighting the following conclusions: It is possible to localize major fracture zones during the pre-investigation at shallow (<200 m) depths; A number of minor fracture zones striking NNW-NNE were predicted to be hydraulically important and penetrate the southern area. A number of narrow fracture zone indications - 0.1-1 m wide - striking WNW-NE were mapped in the tunnel and pre-grouted sections confirm hydraulic conductors; It has not been possible to confirm the gently dipping zone EW-5, which was predicted as `possible`, with data from the tunnel; Predictions of the amount of different rock types were generally reliable as regards the major rocks, but the prediction of the distribution in space were poor as regards the minor rock types; The prediction of rock stress orientation corresponds well to the outcome; The prediction of rock quality for the tunnel, while applying the RMR-system, shows good correspondence to the observations made in the tunnel. 59 refs, 51 figs, 21 tabs.

Comparing the New Madrid Seismic Zone with the Osning Thrust: implications for GIA-induced intraplate tectonics in northern Germany

Science.gov (United States)

Brandes, Christian; Steffen, Holger; Wu, Patrick; Tanner, David; Winsemann, Jutta

2013-04-01

Continental intraplate tectonics is a widespread phenomenon that causes significant earthquakes. These earthquakes even occur in areas that are characterized by low strain rates and there are often long intervals between the individual seismic events (Gangopadhyay & Talwani, 2003) that result in a hazard potential. To better understand the controlling factors of intraplate plate earthquakes in northern Germany, we compare the Osning Thrust with the intensively-studied New Madrid Seismic Zone in the Midwest USA. Both areas share major similarities such as a failed rift-basin setting, the presence of intrusive magmatic bodies in the subsurface, tectonic reactivation during the Late Cretaceous, paleo- and historic seismicity and comparable fault parameters. In addition, both areas have a very similar Late Pleistocene deglaciation history. New Madrid was c. 340 km south of the Laurentide ice sheet and ice retreat started around 21 ka and was completed by 8.5 ka (Grollimund & Zoback, 2001). The Osning Thrust was c. 310 km south of the Scandinavian ice sheet and deglaciation began at 24 ka. Both areas show historic seismicity in a similar time frame (New Madrid Seismic Zone: 1811-1812, Johnston & Schweig, 1996); Osning Thrust: 1612 and 1767, Grünthal & Bosse, 1997). We use numerical simulations to identify the timing of potentially GIA-induced fault activity, which are based on the fault stability margin concept of Wu & Hasegawa (1996). From our modelling results it is evident that the fault stability margin changed to negative between 16 and 13 ka for the Osning Thrust, which matches the OSL data of fault-related growth strata (Brandes et al., 2012). For the New Madrid Seismic Zone, the fault stability margin becomes zero between 2.5 ka BP (before 1812) to about 2 ka after the 1812 event, depending on the parameters of the model. This indicates that for both seismic zones, seismicity due to deglaciation was and still is very likely. From this study it can be derived

Two decades of spatiotemporal variations in subduction zone coupling offshore Japan

Science.gov (United States)

Loveless, John P.; Meade, Brendan J.

2016-02-01

the 1994 event until 2011, coseismic-sense slip precedes the Tohoku-oki event, and coupling offshore northern Honshu is reduced after the 2011 earthquake. Despite the occurrence of the 2003 Tokachi-oki earthquake, persistent coupling offshore Hokkaido suggests ongoing seismic hazard, possibly similar to past MW ∼ 9-class earthquakes interpreted from coastal paleoseismic records. This time-dependent analysis of interseismic deformation illuminates rich diversity in the distribution of subduction zone coupling, including spatiotemporal stability in coupling, effective reduction in strongly coupled regions due to aseismic thrust-sense slip events, and broad changes in the distribution of coupling following major earthquakes.

Instrumentation for coastal zone management

Digital Repository Service at National Institute of Oceanography (India)

Joseph, A.

stream_size 11 stream_content_type text/plain stream_name Trg_Course_Coast_Zone_Manage_1993_91.pdf.txt stream_source_info Trg_Course_Coast_Zone_Manage_1993_91.pdf.txt Content-Encoding ISO-8859-1 Content-Type text/plain; charset...

Management of coastal zone vegetation

Digital Repository Service at National Institute of Oceanography (India)

Untawale, A.G.

stream_size 14 stream_content_type text/plain stream_name Trg_Course_Coast_Zone_Manage_1993_22.pdf.txt stream_source_info Trg_Course_Coast_Zone_Manage_1993_22.pdf.txt Content-Encoding ISO-8859-1 Content-Type text/plain; charset...

The normal zone propagation in ATLAS B00 model coil

CERN Document Server

Boxman, E W; ten Kate, H H J

2002-01-01

The B00 model coil has been successfully tested in the ATLAS Magnet Test Facility at CERN. The coil consists of two double pancakes wound with aluminum stabilized cables of the barrel- and end-cap toroids conductors for the ATLAS detector. The magnet current is applied up to 24 kA and quenches are induced by firing point heaters. The normal zone velocity is measured over a wide range of currents by using pickup coils, voltage taps and superconducting quench detectors. The signals coming from various sensors are presented and analyzed. The results extracted from the various detection methods are in good agreement. It is found that the characteristic velocities vary from 5 to 20 m/s at 15 and 24 kA respectively. In addition, the minimum quench energies at different applied magnet currents are presented. (6 refs).

Effect of ion entry acceptance conditions on the performance of a quadrupole mass spectrometer operated in upper and lower stability regions

International Nuclear Information System (INIS)

Turner, P.; Taylor, S.; Gibson, J.R.

2005-01-01

Computer simulation of ion motion in a quadrupole mass spectrometer has been used to examine the effect of initial ion conditions on performance when operated in the first and third zones of the Mathieu stability diagram. Commercial instruments frequently use round electrodes instead of the better-performing hyperbolic electrodes because the cost of manufacturing is lower. However, adverse features are seen when using round electrodes. Here further insight is provided and a possible method of correction is suggested. For the first time, ion origin for the first stability region for a round electrode quadrupole has been reported

The controversy around the Stability and Growth Pact

Directory of Open Access Journals (Sweden)

Jolanta Ciak

2011-12-01

Full Text Available Pact for Stability and Growth was to be a reliable way to ensure public finances. It commits the Economic Union countries to presenting a monetary budget in the medium term. The idea is to achieve a situation close to a balance in the budget, even a surplus. The deterioration of the fiscal situation of the European Union countries, including the euro area countries, especially in recent times, forcing the introduction of changes to the existing rules of the Pact. Undoubtedly, the introduction of the changes proposed by the European Commission should impact positively on the change in the approach to the problems of excessive deficits and public debt to GDP for the euro area, as well as for the future members of this zone in connection with ongoing processes of European integration.

Normal zone soliton in large composite superconductors

International Nuclear Information System (INIS)

Kupferman, R.; Mints, R.G.; Ben-Jacob, E.

1992-01-01

The study of normal zone of finite size (normal domains) in superconductors, has been continuously a subject of interest in the field of applied superconductivity. It was shown that in homogeneous superconductors normal domains are always unstable, so that if a normal domain nucleates, it will either expand or shrink. While testing the stability of large cryostable composite superconductors, a new phenomena was found, the existence of stable propagating normal solitons. The formation of these propagating domains was shown to be a result of the high Joule power generated in the superconductor during the relatively long process of current redistribution between the superconductor and the stabilizer. Theoretical studies were performed in investigate the propagation of normal domains in large composite super conductors in the cryostable regime. Huang and Eyssa performed numerical calculations simulating the diffusion of heat and current redistribution in the conductor, and showed the existence of stable propagating normal domains. They compared the velocity of normal domain propagation with the experimental data, obtaining a reasonable agreement. Dresner presented an analytical method to solve this problem if the time dependence of the Joule power is given. He performed explicit calculations of normal domain velocity assuming that the Joule power decays exponentially during the process of current redistribution. In this paper, the authors propose a system of two one-dimensional diffusion equations describing the dynamics of the temperature and the current density distributions along the conductor. Numerical simulations of the equations reconfirm the existence of propagating domains in the cryostable regime, while an analytical investigation supplies an explicit formula for the velocity of the normal domain

White Light Photorefractive Phase Zone Plates

International Nuclear Information System (INIS)

Yuan-Mei, Gao; Si-Min, Liu

2008-01-01

Incoherent white light from an incandescent source is employed to fabricate volume phase zone plates in LiNbO 3 : Fe, for the first time to our knowledge, which can guide and modulate the input white light or laser light. The diffractive efficiency of the white light volume phase zone plates fabricated can reach as high as 12%. In addition, we test the volume phase zone plates by a probe beam and find that the volume phase zone plate is present in the direction perpendicular to the c-axis and absent in the direction parallel to the c-axis. This directly proves the existence of photovoltaic photorefractive anisotropy of white light

Radiopaque zones in the dentin beneath amalgam restorations

International Nuclear Information System (INIS)

You, Young Jun; Ahn, Hyung Kyu

1978-01-01

The purpose of the present investigation is determine how frequently radiopaque zones are seen on standard intraoral film and to research some other things about radiopaque bones. This study obtained the following results: 1. According to the standard intraoral films of the charts that were kept at the Dept. of Oral Diagnosis in Seoul National University Hospital, radiopaque zones were found in the rate of 4.1% among 1150 cases of amalgam-restored teeth that were treated at least two years ago. 2. Out of teeth that possessed radiopaque zones, 38.3% had radiolucent area between amalgam restoration and radiopaque zone. 3. Out of teeth that possessed radiopaque zones, 36.2% had cement base between amalgam restoration and radiopaque zone. 4. Out of teeth that possessed radiopaque zones, no tooth had periapical radiolucency. 5. Radiopaque zones were found more frequently in the mandibular teeth than the maxillary teeth. 6. According to the result of direct x-ray taking of 50 teeth that were treated at least 2 years ago, 6% had radiopaque zone.

Seismotectonic zoning of Azerbaijan territory

Science.gov (United States)

Kangarli, Talat; Aliyev, Ali; Aliyev, Fuad; Rahimov, Fuad

2017-04-01

Studying of the space-time correlation and consequences effect between tectonic events and other geological processes that have created modern earth structure still remains as one of the most important problems in geology. This problem is especially important for the East Caucasus-South Caspian geodynamic zone. Being situated at the eastern part of the Caucasian strait, this zone refers to a center of Alpine-Himalayan active folded belt, and is known as a complex tectonic unit with jointing heterogeneous structural-substantial complexes arising from different branches of the belt (Doburja-Caucasus-Kopetdag from the north and Pyrenean-Alborz from the south with Kura and South Caspian zone). According to GPS and precise leveling data, activity of regional geodynamic processes shows intensive horizontal and vertical movements of the Earth's crust as conditioned by collision of the Arabian and Eurasian continental plates continuing since the end of Miocene. So far studies related to the regional of geology-geophysical data, periodically used for the geological and tectonic modeling of the environment mainly based on the fixing ideology. There still remains a number of uncertainties in solution of issues related to regional geology, tectonics and magmatism, structure and interrelation of different structural zones, space-time interrelations between onshore and offshore complexes, etc. At the same time large dataset produced by surface geological surveys, deep geological mapping of on- and offshore areas with the use of seismic and electrical reconnaissance and geophysical field zoning methods, deep well drilling and remote sensing activities. Conducted new studies produced results including differentiation of formerly unknown nappe complexes of the different ages and scales within the structure of mountain-fold zones, identification of new zones containing ophiolites in their section, outlining of currently active faulting areas, geophysical interpretation of the deep

Application of the zone-melting technique to metal chelate systems-VI A new apparatus for zone-melting chromatography.

Science.gov (United States)

Maeda, S; Kobayashi, H; Ueno, K

1973-07-01

An improved apparatus has been constructed for zone-melting chromatography. An essential feature of the apparatus is that the length of the molten zone can be kept constant during a zone-melting operation, by employing heating and cooling compartments which are separated from each other by double partition plates. Each compartment is heated or cooled with jets of hot or cold air. The apparatus is suitable for organic materials melting in the range between 40 degrees and 180 degrees . The distribution of metal ion along the column after zone melting of copper acetylacetonate in 2-methoxynaphthalene was a smooth curve. The plot of the position of maximum concentration, x(max), against the number of zone passes, n, gave a relationship in accordance with theoretical prediction.

Strengthening carbonate roof rock of workings by the use of resins in Karst disturbance zones

Energy Technology Data Exchange (ETDEWEB)

Timofeev, O.V.; Gerovich, E.G.

1977-12-01

Test results are given for a proposed method of injection strengthening of rock in sinkhole areas in order to stabilize the rock of mining areas. Tests were made of appropriately selected NaOH solutions to act as catalysts in the injection of resins. Relationships are given between the hardening time of the aqueous resin solutions and the concentration of the NaOH catalyst, the relationship between the viscosity of the resin solutions and the temperature at specific ratios, between the hardness of the polymer materials and age, and between the resinous mixture compression strength and its age at specific temperatures. A diagram is presented of the injection equipment, and data are presented on the number of boreholes receiving the injected resin in relation to physical measurements. The tests of the resinated areas indicate that the rock hardness of the treated zones approaches that of the fissured zones so that props with less supporting power can be used, and work safety is increased. 3 references, 6 figures, 1 table.

Calcium-dependent depletion zones in the cortical microtubule array coincide with sites of, but do not regulate, wall ingrowth papillae deposition in epidermal transfer cells

Science.gov (United States)

Zhang, Hui-ming; Talbot, Mark J.; McCurdy, David W.; Patrick, John W.; Offler, Christina E.

2015-01-01

Trans-differentiation to a transfer-cell morphology is characterized by the localized deposition of wall ingrowth papillae that protrude into the cytosol. Whether the cortical microtubule array directs wall ingrowth papillae formation was investigated using a Vicia faba cotyledon culture system in which their adaxial epidermal cells were spontaneously induced to trans-differentiate to transfer cells. During deposition of wall ingrowth papillae, the aligned cortical microtubule arrays in precursor epidermal cells were reorganized into a randomized array characterized by circular depletion zones. Concurrence of the temporal appearance, spatial pattern, and size of depletion zones and wall ingrowth papillae was consistent with each papilla occupying a depletion zone. Surprisingly, microtubules appeared not to regulate construction of wall ingrowth papillae, as neither depolymerization nor stabilization of cortical microtubules changed their deposition pattern or morphology. Moreover, the size and spatial pattern of depletion zones was unaltered when the formation of wall ingrowth papillae was blocked by inhibiting cellulose biosynthesis. In contrast, the depletion zones were absent when the cytosolic calcium plumes, responsible for directing wall ingrowth papillae formation, were blocked or dissipated. Thus, we conclude that the depletion zones within the cortical microtubule array result from localized depolymerization of microtubules initiated by elevated cytosolic Ca2+ levels at loci where wall ingrowth papillae are deposited. The physiological significance of the depletion zones as a mechanism to accommodate the construction of wall ingrowth papillae without compromising maintenance of the plasma membrane–microtubule inter-relationship is discussed. PMID:26136268

Stability Performance of Inductively Coupled Plasma Mass Spectrometry-Phenotyped Kernel Minerals Concentration and Grain Yield in Maize in Different Agro-Climatic Zones.

Science.gov (United States)

Mallikarjuna, Mallana Gowdra; Thirunavukkarasu, Nepolean; Hossain, Firoz; Bhat, Jayant S; Jha, Shailendra K; Rathore, Abhishek; Agrawal, Pawan Kumar; Pattanayak, Arunava; Reddy, Sokka S; Gularia, Satish Kumar; Singh, Anju Mahendru; Manjaiah, Kanchikeri Math; Gupta, Hari Shanker

2015-01-01

Deficiency of iron and zinc causes micronutrient malnutrition or hidden hunger, which severely affects ~25% of global population. Genetic biofortification of maize has emerged as cost effective and sustainable approach in addressing malnourishment of iron and zinc deficiency. Therefore, understanding the genetic variation and stability of kernel micronutrients and grain yield of the maize inbreds is a prerequisite in breeding micronutrient-rich high yielding hybrids to alleviate micronutrient malnutrition. We report here, the genetic variability and stability of the kernel micronutrients concentration and grain yield in a set of 50 maize inbred panel selected from the national and the international centres that were raised at six different maize growing regions of India. Phenotyping of kernels using inductively coupled plasma mass spectrometry (ICP-MS) revealed considerable variability for kernel minerals concentration (iron: 18.88 to 47.65 mg kg(-1); zinc: 5.41 to 30.85 mg kg(-1); manganese: 3.30 to 17.73 mg kg(-1); copper: 0.53 to 5.48 mg kg(-1)) and grain yield (826.6 to 5413 kg ha(-1)). Significant positive correlation was observed between kernel iron and zinc within (r = 0.37 to r = 0.52, p kernel minerals concentration and grain yield. Most of the variation was contributed by genotype main effect for kernel iron (39.6%), manganese (41.34%) and copper (41.12%), and environment main effects for both kernel zinc (40.5%) and grain yield (37.0%). Genotype main effect plus genotype-by-environment interaction (GGE) biplot identified several mega environments for kernel minerals and grain yield. Comparison of stability parameters revealed AMMI stability value (ASV) as the better representative of the AMMI stability parameters. Dynamic stability parameter GGE distance (GGED) showed strong and positive correlation with both mean kernel concentrations and grain yield. Inbreds (CM-501, SKV-775, HUZM-185) identified from the present investigation will be useful in

The quantitative soil quality assessment tobacco plant in Sindoro mountainous zone

Directory of Open Access Journals (Sweden)

Supriyadi

2014-04-01

Full Text Available The long-term cultivation of tobacco (Nicotiana tabacum plant in the Sindoro mountainous zone of Central Java has resulted in soil quality degradation that could affect economic development in the region if sustainable production practices are not identified. The objective of the study was to identify appropriate indicators for assessing soil quality on tobacco plant. The quantitative soil quality indicators were total organic-C, pH, available P and available K (chemical, soil depth, bulk density, AWC (available water capacity and soil aggregate stability (physical, and qCO2 (soil respiration, MBC (microbial biomass carbon (biological. The decreases in the soil aggregate stability, available water capacity, cation exchange capacity, soil respiration, microbial biomass carbon and total organic-C; or increases in bulk density (compaction, available P, available K and total nitrogen indicated the decrease in soil quality due to long-term tobacco production. The result of this research showed that the change of soil quality had occurred in Sindoro Mountain. The Soil Quality Index (SQI for three land use systems in Sindoro mountain (forest, mixed farm, and tobacco were 0.60, 0.47, and 0.57, respectively. The comparison of these rates with soil quality classes showed that the soil quality presented moderate to good level of quality; class SQI.

Stability of spanwise-modulated flows behind backward-facing steps

Science.gov (United States)

Boiko, A. V.; Dovgal, A. V.; Sorokin, A. M.

2017-10-01

An overview and synthesis of researches on development of local vortical disturbances in laminar separated flows downstream of backward-facing steps, in which the velocity field depends essentially on two variables are given. Peculiarities of transition to turbulence in such spatially inhomogeneous separated zones are discussed. The experimental data are supplemented by the linear stability characteristics of model velocity profiles of the separated flow computed using both the classical local formulation and the nonlocal approach based on the Floquet theory for partial differential equations with periodic coefficients. The results clarify the response of the local separated flows to their modulation with stationary geometrical and temperature inhomogeneities. The results can be useful for the development of new methods of laminar separation control.

Differences in quantitative assessment of myocardial scar and gray zone by LGE-CMR imaging using established gray zone protocols.

Science.gov (United States)

Mesubi, Olurotimi; Ego-Osuala, Kelechi; Jeudy, Jean; Purtilo, James; Synowski, Stephen; Abutaleb, Ameer; Niekoop, Michelle; Abdulghani, Mohammed; Asoglu, Ramazan; See, Vincent; Saliaris, Anastasios; Shorofsky, Stephen; Dickfeld, Timm

2015-02-01

Late gadolinium enhancement cardiac magnetic resonance (LGE-CMR) imaging is the gold standard for myocardial scar evaluation. Heterogeneous areas of scar ('gray zone'), may serve as arrhythmogenic substrate. Various gray zone protocols have been correlated to clinical outcomes and ventricular tachycardia channels. This study assessed the quantitative differences in gray zone and scar core sizes as defined by previously validated signal intensity (SI) threshold algorithms. High quality LGE-CMR images performed in 41 cardiomyopathy patients [ischemic (33) or non-ischemic (8)] were analyzed using previously validated SI threshold methods [Full Width at Half Maximum (FWHM), n-standard deviation (NSD) and modified-FWHM]. Myocardial scar was defined as scar core and gray zone using SI thresholds based on these methods. Scar core, gray zone and total scar sizes were then computed and compared among these models. The median gray zone mass was 2-3 times larger with FWHM (15 g, IQR: 8-26 g) compared to NSD or modified-FWHM (5 g, IQR: 3-9 g; and 8 g. IQR: 6-12 g respectively, p zone extent (percentage of total scar that was gray zone) also varied significantly among the three methods, 51 % (IQR: 42-61 %), 17 % (IQR: 11-21 %) versus 38 % (IQR: 33-43 %) for FWHM, NSD and modified-FWHM respectively (p zone and scar core. Infarct core and total myocardial scar mass also differ using these methods. Further evaluation of the most accurate quantification method is needed.

Site characterization and evaluation of the stability of the Yesilyurt Landslide (Trabzon, NE Turkey) using back analysis method

Science.gov (United States)

Kul Yahşi, Bilgehan; Ersoy, Hakan

2018-06-01

The aim of this study was to determine the soil profile of the Yeşilyurt Landslide Area (NE Turkey) and to investigate the stability of the landslide area after the excavation planned by back analysis for support design. For these purposes, after the 1/1000 scaled engineering geological map was prepared, seismic refraction, electrical resistivity tomography and ground penetrating radar measurements were performed on different profiles to understand vertical and horizontal homogeneity of the landslide materials and undisturbed/disturbed soil samples were obtained from the test pits to determine the geotechnical properties of the soil. The results of the geophysical measurements showed that the landslide material was composed of two different soil zones. While the maximum thickness of the upper zone is 2.5, the thickness of the lower zone is about 5 m. The depth of dasidic rock mass is about 7 m. Residual cohesions of the soil samples obtained upper and lower zones were determined as 38 kPa and 44 kPa, and their residual friction angles were determined as 18° and 15° respectively. Unit weight values of the soil samples obtained from both zones were 16.9 kN m-3. The data obtained from laboratory tests showed that the landslide material is a uniform lithology. The geophysical measurements indicate that the wave velocity and resistivity values of these profiles differ from each other due to groundwater at a depth of 2.5 m. Limit equilibrium analysis were carried out with Slide v5.0 software using data obtained from the field measurements and laboratory tests to evaluate current and supported cases of the studied area. Because the safety factor of the slope obtained from the LE analyses is 0.99 and the studied soil environment is considered as unstable, the reliable and economical reinforcement was suggested using the retaining wall. The back-analysis method was evaluated to ensure the stability for a 1.5 safety factor and finally the lateral active forces for the

Fracture zones constrained by neutral surfaces in a fault-related fold: Insights from the Kelasu tectonic zone, Kuqa Depression

Science.gov (United States)

Sun, Shuai; Hou, Guiting; Zheng, Chunfang

2017-11-01

Stress variation associated with folding is one of the controlling factors in the development of tectonic fractures, however, little attention has been paid to the influence of neutral surfaces during folding on fracture distribution in a fault-related fold. In this study, we take the Cretaceous Bashijiqike Formation in the Kuqa Depression as an example and analyze the distribution of tectonic fractures in fault-related folds by core observation and logging data analysis. Three fracture zones are identified in a fault-related fold: a tensile zone, a transition zone and a compressive zone, which may be constrained by two neutral surfaces of fold. Well correlation reveals that the tensile zone and the transition zone reach the maximum thickness at the fold hinge and get thinner in the fold limbs. A 2D viscoelastic stress field model of a fault-related fold was constructed to further investigate the mechanism of fracturing. Statistical and numerical analysis reveal that the tensile zone and the transition zone become thicker with decreasing interlimb angle. Stress variation associated with folding is the first level of control over the general pattern of fracture distribution while faulting is a secondary control over the development of local fractures in a fault-related fold.

Separate zones of sulfate and sulfide release from subducted mafic oceanic crust

Science.gov (United States)

Tomkins, Andrew G.; Evans, Katy A.

2015-10-01

Liberation of fluids during subduction of oceanic crust is thought to transfer sulfur into the overlying sub-arc mantle. However, despite the importance of sulfur cycling through magmatic arcs to climate change, magma oxidation and ore formation, there has been little investigation of the metamorphic reactions responsible for sulfur release from subducting slabs. Here, we investigate the relative stability of anhydrite (CaSO4) and pyrite (FeS2) in subducted basaltic oceanic crust, the largest contributor to the subducted sulfur budget, to place constraints on the processes controlling sulfur release. Our analysis of anhydrite stability at high pressures suggests that this mineral should dominantly dissolve into metamorphic fluids released across the transition from blueschist to eclogite facies (∼450-650 °C), disappearing at lower temperatures on colder geothermal trajectories. In contrast, we suggest that sulfur release via conversion of pyrite to pyrrhotite occurs at temperatures above 750 °C. This higher temperature stability is indicated by the preservation of pyrite-bornite inclusions in coesite-bearing eclogites from the Sulu Belt in China, which reached temperatures of at least 750 °C. Thus, sulfur may be released from subducting slabs in two separate pulses; (1) varying proportions of SO2, HSO4- and H2S are released via anhydrite breakdown at the blueschist-eclogite transition, promoting oxidation of remaining silicates in some domains, and (2) H2S is released via pyrite breakdown well into the eclogite facies, which may in some circumstances coincide with slab melting or supercritical liquid generation driven by influx of serpentinite-derived fluids. These results imply that the metallogenic potential in the sub-arc mantle above the subducting slab varies as a function of subduction depth, having the greatest potential above the blueschist-eclogite transition given the association between oxidised magmas and porphyry Cu(-Au-Mo) deposits. We speculate

76 FR 7107 - Quarterly Listings; Safety Zones, Security Zones, Special Local Regulations, Drawbridge Operation...

Science.gov (United States)

2011-02-09

... defined boundary for which regulations for vessels navigating within the area have been established by the...)...... 9/19/2008 USCG-2008-0814 San Diego, CA Safety Zones (Part 165)...... 9/6/2008 USCG-2008-0827 Ocean... (Part 165). USCG-2009-0402 Ocean City, NJ Safety Zones (Part 165)...... 10/10/2009 USCG-2009-0403...

Seasonal Ice Zone Reconnaissance Surveys Coordination

Science.gov (United States)

2016-03-30

Chukchi sea seasonal sea ice zone (SIZ) utilizing US Coast Guard Arctic Domain Awareness ( ADA ) flights of opportunity in the summers of 2012- 2014. In...measurements across the Beaufort-Chukchi sea seasonal sea ice zone (SIZ) utilizing US Coast Guard Arctic Domain Awareness ( ADA ) flights of...such, it contains the full range of positions of the marginal ice zone (MIZ) where sea ice interacts with open water. In addition to SIZRS

Flow structures in a lean-premixed swirl-stabilized combustor with microjet air injection

KAUST Repository

LaBry, Zachary A.

2011-01-01

The major challenge facing the development of low-emission combustors is combustion instability. By lowering flame temperatures, lean-premixed combustion has the potential to nearly eliminate emissions of thermally generated nitric oxides, but the chamber acoustics and heat release rate are highly susceptible to coupling in ways that lead to sustained, high-amplitude pressure oscillations, known as combustion instability. At different operating conditions, different modes of instability are observed, corresponding to particular flame shapes and resonant acoustic modes. Here we show that in a swirl-stabilized combustor, these instability modes also correspond to particular interactions between the flame and the inner recirculation zone. Two stable and two unstable modes are examined. At lean equivalence ratios, a stable conical flame anchors on the upstream edge of the inner recirculation zone and extends several diameters downstream along the wall. At higher equivalence ratios, with the injection of counter-swirling microjet air flow, another stable flame is observed. This flame is anchored along the upstream edge of a stronger recirculation zone, extending less than one diameter downstream along the wall. Without the microjets, a stationary instability coupled to the 1/4 wave mode of the combustor shows weak velocity oscillations and a stable configuration of the inner and outer recirculation zones. Another instability, coupled to the 3/4 wave mode of the combustor, exhibits periodic vortex breakdown in which the core flow alternates between a columnar mode and a vortex breakdown mode. © 2010 Published by Elsevier Inc. on behalf of The Combustion Institute. All rights reserved.

Environmental Zoning: Some methodological implications

NARCIS (Netherlands)

Ike, Paul; Voogd, Henk

1991-01-01

The purpose of this article is to discuss some methodological problems of environmental zoning. The principle of environmental zoning will be elaborated. In addition an overview is given of a number of approaches that have been followed in practice to arrive at an integral judgement. Finally some

Growth with Time Zone Differences

OpenAIRE

Toru Kikuchi; Sugata Marjit

2010-01-01

We propose a two-country growth model of intermediate business-services trade that captures the role of time zone differences. It is shown that a time-saving improvement in intermediate business-services trade involving production in different time zones can have a permanent impact on productivity.

The segmentation of zones with increased autofluorescence in the junctional zone of parapapillary atrophy

International Nuclear Information System (INIS)

Kolář, R; Jan, J; Laemmer, R; Mardin, Ch Y

2009-01-01

The autofluorescence (AF) derived from the retinal pigment epithelium has the potential to be used as a feature for early glaucoma diagnosis. The aim of this paper is to design and evaluate the method used for semi-automatic segmentation of the zones with increased autofluorescence. A randomized sample of 20 patients (age: 56 ± 10 years) with open angle glaucoma was used. A new method for semi-automatic detection and segmentation of the zones with a higher level of autofluorescence in the junctional zone of parapapillary atrophy has been evaluated. Good agreement has been observed between manually and semi-automatically segmented zones for most of the images, but higher differences may occur for larger hyperfluorescent regions. The data were evaluated using the limits of agreement, with a 2σ border. The described method allows fast and objective evaluation of AF images, preventing undesirable inter-expert variance. A large proportion of AF images could be evaluated successfully by the developed procedure, and the obtained results are comparable to the manual procedure in most cases

Double seismic zone for deep earthquakes in the izu-bonin subduction zone.

Science.gov (United States)

Iidaka, T; Furukawa, Y

1994-02-25

A double seismic zone for deep earthquakes was found in the Izu-Bonin region. An analysis of SP-converted phases confirms that the deep seismic zone consists of two layers separated by approximately 20 kilometers. Numerical modeling of the thermal structure implies that the hypocenters are located along isotherms of 500 degrees to 550 degrees C, which is consistent with the hypothesis that deep earthquakes result from the phase transition of metastable olivine to a high-pressure phase in the subducting slab.

Purification by using the zone melting technique; Purification par la technique de la zone fondue

Energy Technology Data Exchange (ETDEWEB)

Clerc, Michel

1962-06-22

The zone melting technique has first been used in metallurgy, and has been developed for the preparation of silicon and germanium for semiconductors, and then for the preparation of organic bodies of high purity. In this research thesis, the author first presents the principle of this technique, and then discusses the influence of agitation in liquid phase, and the influence of the number of passages over the zone. He discusses issues related to matter transport, and some technical details which intervene in the design of an apparatus for purification by zone melting. He finally presents examples.

Mechanisms of stabilization and blowoff of a premixed flame downstream of a heat-conducting perforated plate

KAUST Repository

Kedia, Kushal S.

2012-03-01

The objective of this work is to investigate the flame stabilization mechanism and the conditions leading to the blowoff of a laminar premixed flame anchored downstream of a heat-conducting perforated-plate/multi-hole burner, with overall nearly adiabatic conditions. We use unsteady, fully resolved, two-dimensional simulations with detailed chemical kinetics and species transport for methane-air combustion. Results show a bell-shaped flame stabilizing above the burner plate hole, with a U-shaped section anchored between neighboring holes. The base of the positively curved U-shaped section of the flame is positioned near the stagnation point, at a location where the flame displacement speed is equal to the flow speed. This location is determined by the combined effect of heat loss and flame stretch on the flame displacement speed. As the mass flow rate of the reactants is increased, the flame displacement speed at this location varies non-monotonically. As the inlet velocity is increased, the recirculation zone grows slowly, the flame moves downstream, and the heat loss to the burner decreases, strengthening the flame and increasing its displacement speed. As the inlet velocity is raised, the stagnation point moves downstream, and the flame length grows to accommodate the reactants mass flow. Concomitantly, the radius of curvature of the flame base decreases until it reaches an almost constant value, comparable to the flame thickness. While the heat loss decreases, the higher flame curvature dominates thereby reducing the displacement speed of the flame base. For a stable flame, the gradient of the flame base displacement speed normal to the flame is higher than the gradient of the flow speed along the same direction, leading to dynamic stability. As inlet velocity is raised further, the former decreases while the latter increases until the stability condition is violated, leading to blowoff. The flame speed during blow off is determined by the feedback between the

ZONING DESIGN FOR HAND­WRITTEN NUMERAL RECOGNITION

NARCIS (Netherlands)

Lecce Di, V.; Dimauro, G.; Guerriero, A.; Impedovo, S.; Pirlo, G.; Salzo, A.

2004-01-01

In the field of Optical Character Recognition (OCR), zoning is used to extract topological information from patterns. In this paper zoning is considered as the result of an optimisation problem and a new technique is presented for automatic zoning. More precisely, local analysis of feature

Critical Zone services as environmental assessment criteria in intensively managed landscapes

Science.gov (United States)

Richardson, Meredith; Kumar, Praveen

2017-06-01

The Critical Zone (CZ) includes the biophysical processes occurring from the top of the vegetation canopy to the weathering zone below the groundwater table. CZ services provide a measure for the goods and benefits derived from CZ processes. In intensively managed landscapes, cropland is altered through anthropogenic energy inputs to derive more productivity, as agricultural products, than would be possible under natural conditions. However, the actual costs of alterations to CZ functions within landscape profiles are unknown. Through comparisons of corn feed and corn-based ethanol, we show that valuation of these CZ services in monetary terms provides a more concrete tool for characterizing seemingly abstract environmental damages from agricultural production systems. Multiple models are combined to simulate the movement of nutrients throughout the soil system, enabling the measurement of agricultural anthropogenic impacts to the CZ's regulating services. Results indicate water quality and atmospheric stabilizing services, measured by soil carbon storage, carbon respiration, and nitrate leaching, among others, can cost more than double that of emissions estimated in previous studies. Energy efficiency in addition to environmental impact is assessed to demonstrate how the inclusion of CZ services is necessary in accounting for the entire life cycle of agricultural production systems. These results conclude that feed production systems are more energy efficient and less environmentally costly than corn-based ethanol.

Structural and Stratigraphic Controls on Methane Hydrate occurrence and distribution: Gulf of Mexico, Walker Ridge 313 and Green Canyon 955: Final Report

Energy Technology Data Exchange (ETDEWEB)

Jaiswal, Priyank [Oklahoma State Univ., Stillwater, OK (United States)

2017-09-01

The goal of this project was to determine structural and stratigraphic controls on hydrate occurrence and distribution in Green Canyon (GC) 955 and Walker Ridge (WR) 313 blocks using seismic and well data. Gas hydrate was discovered in these blocks in coarse- and fine-grained sediments during the 2009 Joint Industrial project (JIP) Leg 11 drilling expedition. Although the immediate interest of the exploration community is exclusively hydrate which is present in coarse–grained sediments, factors that control hydrate and free gas distribution in the two blocks and whether coarse and fine-grained hydrate-bearing units are related in any manner, formed the core of this research. The project spanned from 10/01/2012 to 07/31/2016. In the project, in both the leased blocks, the interval spanning the gas hydrate stability zone (GHSZ) was characterized using a joint analysis of sparse Ocean Bottom Seismic (OBS) and dense, surface–towed multichannel seismic (MCS) data. The project team had the luxury of calibrating their results with two well logs. Advance processing methods such as depth migration and full-waveform inversion (FWI) were used for seismic data analysis. Hydrate quantification was achieved through interpretation of the FWI velocity field using appropriate rock physics models at both blocks. The seismic modeling/inversion methodology (common to both GC955 and WR313 blocks) was as follows. First, the MCS data were depth migrated using a P-wave velocity (VP) model constructed using inversion of reflection arrival times of a few (four in both cases) key horizons carefully picked in the OBS data to farthest possible offsets. Then, the resolution of the traveltime VP model was improved to wavelength scale by inverting OBS gathers up to the highest frequency possible (21.75 Hz for GC955 and 17.5 for WR313) using FWI. Finally, the hydrate saturation (or the volume fraction) was estimated at the well location assuming one of the other hydrate morphology (filling the

Radially converging tracer test in a low-angle fracture zone at the Finnsjoen site, central Sweden. The fracture zone project - phase 3

International Nuclear Information System (INIS)

Gustafsson, E.; Nordqvist, R.

1993-10-01

The performance and results of a radially converging tracer test in a low-angle major fracture zone in crystalline rock are described. The extensive, about 100 m thick, zone 2 was encountered by means of borehole investigations at depths ranging from 100 to 250 metres at the Finnsjon site, central eastern Sweden. The zone studied (zone 2) consists of highly conductive, metre thick interconnected minor shear and fracture zones (sub-zones) with low conductive rock in between. The objective of the tracer test was primarily to determine flow and transport characteristics in a major fracture zone. Secondly new equipment, experimental design and methods of interpretation were developed, tested and improved. The converging flow field was created by pumping in a central borehole from a packed-off interval enclosing the whole thickness of zone 2. Tracer breakthrough was registered from all nine injection points, with first arrivals ranging from 24 to 3200 hours. Evaluated flow and transport parameters included; flow porosity, dispersivity, flow wetted surface, fracture aperture and hydraulic conductivity in fracture flow paths. Directional variations were found in the flow and transport parameters determined, which is concluded to be due to heterogeneity and/or anisotropy. This conditions is more pronounced at depth in zone 2. The results from the tracer test also clearly show that the upper boundary of zone 2 is highly conductive and consistent over hundreds of metres. Within zone 2, and between upper and lower margins, interconnected discrete minor shear and fracture zones (sub-zones) constitute flow paths of considerable variable residence times. The dispersion within the sub-zones of zone 2, expressed as Peclet numbers ranged from 16 to 40. Flow porosity was determined to be 0.001-0.05 in the upper sub-zone and 0.01-0.1 in the intermediate and lower ones and flow wetted surface area per volume of rock was calculated to be within 1-92 m 2 /m 3 . 68 refs, 61 figs, 40 tabs

Structure of a swirl-stabilized spray flame by imaging, laser Doppler velocimetry, and phase Doppler anemometry

Science.gov (United States)

Edwards, C. F.; Rudoff, R. C.

1991-01-01

Data are presented which describe the mean structure of a steady, swirl-stabilized, kerosene spray flame in the near-injector region of a research furnace. The data presented include ensemble-averaged results of schlieren, luminosity, and extinction imaging, measurement of the gas phase velocity field by laser Doppler velocimetry, and characterization of the condensed phase velocity by phase Doppler anemometry. The results of these studies define six key regions in the flame: the dense spray region; the rich, two-phase, fuel jet; the main air jet; the internal product recirculation zone; the external product recirculation zone; and the gaseous diffusion flame zone. The first five of these regions form a conical mixing layer which prepares the air and fuel for combustion. The air and fuel jets comprise the central portion of this mixing layer and are bounded on either side by the hot product gases of the internal and external recirculation zones. Entrainment of these product gases into the air/fuel streams provides the energy required to evaporate the fuel spray and initiate combustion. Intermittency of the internal recirculation and spray jet flows accounts for unexpected behavior observed in the aerodynamics of the two phases. The data reported herein are part of the database being accumulated on this spray flame for the purpose of detailed comparison with numerical modeling.

Agar agar-stabilized milled zerovalent iron particles for in situ groundwater remediation

Energy Technology Data Exchange (ETDEWEB)

Velimirovic, Milica; Schmid, Doris; Wagner, Stephan; Micić, Vesna; Kammer, Frank von der; Hofmann, Thilo, E-mail: thilo.hofmann@univie.ac.at

2016-09-01

Submicron-scale milled zerovalent iron (milled ZVI) particles produced by grinding macroscopic raw materials could provide a cost-effective alternative to nanoscale zerovalent iron (nZVI) particles for in situ degradation of chlorinated aliphatic hydrocarbons in groundwater. However, the aggregation and settling of bare milled ZVI particles from suspension presents a significant obstacle to their in situ application for groundwater remediation. In our investigations we reduced the rapid aggregation and settling rate of bare milled ZVI particles from suspension by stabilization with a “green” agar agar polymer. The transport potential of stabilized milled ZVI particle suspensions in a diverse array of natural heterogeneous porous media was evaluated in a series of well-controlled laboratory column experiments. The impact of agar agar on trichloroethene (TCE) removal by milled ZVI particles was assessed in laboratory-scale batch reactors. The use of agar agar significantly enhanced the transport of milled ZVI particles in all of the investigated porous media. Reactivity tests showed that the agar agar-stabilized milled ZVI particles were reactive towards TCE, but that their reactivity was an order of magnitude less than that of bare, non-stabilized milled ZVI particles. Our results suggest that milled ZVI particles could be used as an alternative to nZVI particles as their potential for emplacement into contaminated zone, their reactivity, and expected longevity are beneficial for in situ groundwater remediation. - Highlights: • Rapid aggregation and sedimentation were observed in bare milled ZVI particles. • Agar agar improved the stability of milled ZVI particle suspensions. • Agar agar enhanced the transport of milled ZVI particles in heterogeneous sands. • Agar agar reduced the reactivity of milled ZVI particles towards TCE.

Agar agar-stabilized milled zerovalent iron particles for in situ groundwater remediation

International Nuclear Information System (INIS)

Velimirovic, Milica; Schmid, Doris; Wagner, Stephan; Micić, Vesna; Kammer, Frank von der; Hofmann, Thilo

2016-01-01

Submicron-scale milled zerovalent iron (milled ZVI) particles produced by grinding macroscopic raw materials could provide a cost-effective alternative to nanoscale zerovalent iron (nZVI) particles for in situ degradation of chlorinated aliphatic hydrocarbons in groundwater. However, the aggregation and settling of bare milled ZVI particles from suspension presents a significant obstacle to their in situ application for groundwater remediation. In our investigations we reduced the rapid aggregation and settling rate of bare milled ZVI particles from suspension by stabilization with a “green” agar agar polymer. The transport potential of stabilized milled ZVI particle suspensions in a diverse array of natural heterogeneous porous media was evaluated in a series of well-controlled laboratory column experiments. The impact of agar agar on trichloroethene (TCE) removal by milled ZVI particles was assessed in laboratory-scale batch reactors. The use of agar agar significantly enhanced the transport of milled ZVI particles in all of the investigated porous media. Reactivity tests showed that the agar agar-stabilized milled ZVI particles were reactive towards TCE, but that their reactivity was an order of magnitude less than that of bare, non-stabilized milled ZVI particles. Our results suggest that milled ZVI particles could be used as an alternative to nZVI particles as their potential for emplacement into contaminated zone, their reactivity, and expected longevity are beneficial for in situ groundwater remediation. - Highlights: • Rapid aggregation and sedimentation were observed in bare milled ZVI particles. • Agar agar improved the stability of milled ZVI particle suspensions. • Agar agar enhanced the transport of milled ZVI particles in heterogeneous sands. • Agar agar reduced the reactivity of milled ZVI particles towards TCE.

Drivers׳ merging behavior data in highway work zones

Directory of Open Access Journals (Sweden)

Mahmoud Shakouri

2016-03-01

Full Text Available There have been growing research interests in finding a suitable work zone layout to improve work zone safety and traffic efficiency. This paper contains data supporting the research article entitled: Effects of work zone configurations and traffic density on performance variables and subjective workload (Shakouri et al., 2014 [1]. A full factorial experiment was conducted to compare the efficiency of two work zone configurations by using a driving simulator with two levels of work zone configuration, two levels of traffic density and three levels of sign placement as fixed factors. Seven female and 23 male participants completed the experiment. In this paper we present the data relating to demographic information of participants, driving simulator data and subjective workload evaluation of participants for each work zone. Keywords: Work zone, Merging behavior, Subjective workload, Safety

Cable Stability

Energy Technology Data Exchange (ETDEWEB)

Bottura, L [European Organization for Nuclear Research, Geneva (Switzerland)

2014-07-01

Superconductor stability is at the core of the design of any successful cable and magnet application. This chapter reviews the initial understanding of the stability mechanism, and reviews matters of importance for stability such as the nature and magnitude of the perturbation spectrum and the cooling mechanisms. Various stability strategies are studied, providing criteria that depend on the desired design and operating conditions.

Export Processing Zones and Global Class Formation

NARCIS (Netherlands)

Neveling, Patrick

2015-01-01

This chapter is concerned with one of the most striking developments in the global political economy of capitalism after the Second World War; the rise of export processing zones and special economic zones. Building on long-term ethnohistorical research on the zones’ global spread from one zone in

Nuclear free zone

International Nuclear Information System (INIS)

Christoffel, T.

1987-01-01

Health professionals have played a leading role in alerting and educating the public regarding the danger of nuclear war which has been described as the last epidemic our civilization will know. Having convinced most people that the use of nuclear weapons would mean intolerable consequences, groups such as Physicians for Social Responsibility have focused on the second critical question how likely is it that these weapons will be used? The oultlook is grim. This article describes the nuclear free zone movement, explores relevant legal questions, and shows how the political potential of nuclear free zones threatens to open a deep rift in the American constitutional system

A geophysical cross-section of the Hockai Fault Zone (Eastern Belgium): imaging an intraplate weak crustal zone.

Science.gov (United States)

Lecocq, T.; Camelbeeck, T.

2016-12-01

The Hockai Fault Zone (HFZ) is a NNW-SSE trending structure visible in the regional geomorphology in the Ardennes, Eastern-Belgium. It is situated, between the Pays de Herve (Graben de la Minerie) to the North and the Amblève river, to the South. It crosses the Stavelot Massif, almost perpendicular to the Crête de la Vecquée (Vecquée crest), i.e. the highest crest of the Venn. Faults have been identified or suspected on a contour map of the base of the Tertiary cover (Eocene or Oligocene) in the north western and central Rhenish Massif. These faults are necessary to account for the altitude difference of the base of the cover. The deflection or capture of local rivers show a remarkable alignments on more than 42 km N-S. The alignments are mostly trending SSE-NNW, between N140 and N170, with some potential segments with slightly different orientations. This general orientation has been also evidenced from the analyses of Landsat-1 imagery products. At its crossing with the Vecquée Crest, Demoulin locates the HFZ where the Hoëgne river turns sharply towards the north and crosscuts the quarzitic crest. Demoulin identifies three subparallel faults or fault zones on the Hautes-Fagnes plateau, from East to West: the Eupen faulting zone, the Baelen faulting zone and Hockai faulted zone. In this communication, we report on a large-scale geophysical survey that was conducted in order to search of the Hockai fault zone expression at the surface. The locations to search for the Hockai Fault Zone are based on the surface projection of the 1989/1990 seismic swarm that occurred under the Stavelot Massif, geomorphological evidences and past geophysical surveys in the region. Our objective is not to prove a Quaternary movement of faults, but rather to find reliable evidences of their presence and to analyse their lateral extension. In total, 31 ERT profiles were executed almost parallel to the Vecquée Crest, i.e. a total of 10679 meters of profiles. Four zones are imaged

Advanced Vadose Zone Simulations Using TOUGH

Energy Technology Data Exchange (ETDEWEB)

Finsterle, S.; Doughty, C.; Kowalsky, M.B.; Moridis, G.J.; Pan,L.; Xu, T.; Zhang, Y.; Pruess, K.

2007-02-01

The vadose zone can be characterized as a complex subsurfacesystem in which intricate physical and biogeochemical processes occur inresponse to a variety of natural forcings and human activities. Thismakes it difficult to describe, understand, and predict the behavior ofthis specific subsurface system. The TOUGH nonisothermal multiphase flowsimulators are well-suited to perform advanced vadose zone studies. Theconceptual models underlying the TOUGH simulators are capable ofrepresenting features specific to the vadose zone, and of addressing avariety of coupled phenomena. Moreover, the simulators are integratedinto software tools that enable advanced data analysis, optimization, andsystem-level modeling. We discuss fundamental and computationalchallenges in simulating vadose zone processes, review recent advances inmodeling such systems, and demonstrate some capabilities of the TOUGHsuite of codes using illustrative examples.

Metasomatic zoning at some stratiform rare metal deposits

International Nuclear Information System (INIS)

Altyntsev, Yu.V.; Bazhenov, M.I.; Bepeshov, G.V.; Komarnitskij, G.M.; Petrov, I.Ya.; Serykh, A.S.

1985-01-01

Metasomatic zoning of stratiform deposits of rare metals (Mo, Pb, As, V, Se, U, etc.) in intermontane depresions, deposited at the postorogenic stage of Paleozoic geosyncline region development, is considered. Geochemical and geophysical characteristics of metasomatic zoning in the case of sloping and steep rock deposition are given. It is established, that in rare metal deposits in variegated deposits of molassoid formation of Middle-Upper Paleozoic the external and internal zones of metasomatic alterations are distinctly separated. The external zone is presented by mineral association: quartz + -albile + -calcite + -epidote; the internal one - by hydromica + -chlorite + -analcite, laumontite + -hematite + -ankerite + -kaolinite. Geochemical zoning is manifested quite regularly at all the deposits and it is subjected to metasomatic zoning. Changes in physical properties of rocks reflect the metasomatic zoning. The character of metasomatic alterations of rocks, geochemical zoning of metasomatites at rare metal deposits in molassoid deposits and spatially contiguous deposits in volcanogenic complexes have common features. A supposition is made on polygenic ore formation in sedimentary rocks of the depressions

Abnormal Grain Growth in the Heat Affected Zone of Friction Stir Welded Joint of 32Mn-7Cr-1Mo-0.3N Steel during Post-Weld Heat Treatment

Directory of Open Access Journals (Sweden)

Yijun Li

2018-04-01

Full Text Available The abnormal grain growth in the heat affected zone of the friction stir welded joint of 32Mn-7Cr-1Mo-0.3N steel after post-weld heat treatment was confirmed by physical simulation experiments. The microstructural stability of the heat affected zone can be weakened by the welding thermal cycle. It was speculated to be due to the variation of the non-equilibrium segregation state of solute atoms at the grain boundaries. In addition, the pressure stress in the welding process can promote abnormal grain growth in the post-weld heat treatment.

Control of locomotor stability in stabilizing and destabilizing environments.

Science.gov (United States)

Wu, Mengnan/Mary; Brown, Geoffrey; Gordon, Keith E

2017-06-01

To develop effective interventions targeting locomotor stability, it is crucial to understand how people control and modify gait in response to changes in stabilization requirements. Our purpose was to examine how individuals with and without incomplete spinal cord injury (iSCI) control lateral stability in haptic walking environments that increase or decrease stabilization demands. We hypothesized that people would adapt to walking in a predictable, stabilizing viscous force field and unpredictable destabilizing force field by increasing and decreasing feedforward control of lateral stability, respectively. Adaptations in feedforward control were measured using after-effects when fields were removed. Both groups significantly (pfeedforward adaptions to increase control of lateral stability. In contrast, in the destabilizing field, non-impaired subjects increased movement variability (p0.05). When the destabilizing field was removed, increases in movement variability persisted (pfeedforward decreases in resistance to perturbations. Published by Elsevier B.V.

Recent findings relating to firefighter safety zones

Science.gov (United States)

Bret Butler; Russ Parsons; William Mell

2015-01-01

Designation of safety zones is a primary duty of all wildland firefighters. Unfortunately, information regarding what constitutes an adequate safety zone is inadequately defined. Measurements of energy release from wildland fires have been used to develop an empirically based safety zone guideline. The basis for this work is described here.

78 FR 15883 - Standard Time Zone Boundaries

Science.gov (United States)

2013-03-13

...] RIN 2105-AE20 Standard Time Zone Boundaries AGENCY: Office of the Secretary (OST), Department of... time zone boundaries regulations to reflect changes that Congress made to the Uniform Time Act. The... regulations on standard time zone boundaries, 49 CFR Part 71, need to be updated in order to ensure their...

32 CFR 643.33 - Policy-Coastal zone management.

Science.gov (United States)

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Policy-Coastal zone management. 643.33 Section... PROPERTY REAL ESTATE Policy § 643.33 Policy—Coastal zone management. (a) The Coastal Zone Management Act of... affecting the coastal zone of a state, to conduct or support those activities in a manner which is, to the...

Zoning Districts, The zoning districts dataset includes the towns in Manitowoc County, WI that have adopted the county's zoning ordinance., Published in 2013, 1:2400 (1in=200ft) scale, Manitowoc County Government.

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Zoning Districts dataset current as of 2013. The zoning districts dataset includes the towns in Manitowoc County, WI that have adopted the county's zoning ordinance..

Stability Performance of Inductively Coupled Plasma Mass Spectrometry-Phenotyped Kernel Minerals Concentration and Grain Yield in Maize in Different Agro-Climatic Zones.

Directory of Open Access Journals (Sweden)

Mallana Gowdra Mallikarjuna

Full Text Available Deficiency of iron and zinc causes micronutrient malnutrition or hidden hunger, which severely affects ~25% of global population. Genetic biofortification of maize has emerged as cost effective and sustainable approach in addressing malnourishment of iron and zinc deficiency. Therefore, understanding the genetic variation and stability of kernel micronutrients and grain yield of the maize inbreds is a prerequisite in breeding micronutrient-rich high yielding hybrids to alleviate micronutrient malnutrition. We report here, the genetic variability and stability of the kernel micronutrients concentration and grain yield in a set of 50 maize inbred panel selected from the national and the international centres that were raised at six different maize growing regions of India. Phenotyping of kernels using inductively coupled plasma mass spectrometry (ICP-MS revealed considerable variability for kernel minerals concentration (iron: 18.88 to 47.65 mg kg(-1; zinc: 5.41 to 30.85 mg kg(-1; manganese: 3.30 to 17.73 mg kg(-1; copper: 0.53 to 5.48 mg kg(-1 and grain yield (826.6 to 5413 kg ha(-1. Significant positive correlation was observed between kernel iron and zinc within (r = 0.37 to r = 0.52, p < 0.05 and across locations (r = 0.44, p < 0.01. Variance components of the additive main effects and multiplicative interactions (AMMI model showed significant genotype and genotype × environment interaction for kernel minerals concentration and grain yield. Most of the variation was contributed by genotype main effect for kernel iron (39.6%, manganese (41.34% and copper (41.12%, and environment main effects for both kernel zinc (40.5% and grain yield (37.0%. Genotype main effect plus genotype-by-environment interaction (GGE biplot identified several mega environments for kernel minerals and grain yield. Comparison of stability parameters revealed AMMI stability value (ASV as the better representative of the AMMI stability parameters. Dynamic stability

Denuded zone in Czochralski silicon wafer with high carbon content

International Nuclear Information System (INIS)

Chen Jiahe; Yang Deren; Ma Xiangyang; Que Duanlin

2006-01-01

The thermal stability of the denuded zone (DZ) created by high-low-high-temperature annealing in high carbon content (H[C]) and low carbon content (L[C]) Czochralski silicon (Cz-Si) has been investigated in a subsequent ramping and isothermal 1050 deg. C annealing. The tiny oxygen precipitates which might occur in the DZ were checked. It was found in the L[C] Cz-Si that the DZ shrank and the density of bulk micro-defects (BMDs) reduced with the increase of time spent at 1050 deg. C. Also, the DZs above 15 μm of thickness present in the H[C] Cz-Si wafers continuously and the density and total volume of BMDs first decreased then increased and finally decreased again during the treatments. Moreover, tiny oxygen precipitates were hardly generated inside the DZs, indicating that H[C] Cz-Si wafers could support the fabrication of integrated circuits

Denuded zone in Czochralski silicon wafer with high carbon content

Science.gov (United States)

Chen, Jiahe; Yang, Deren; Ma, Xiangyang; Que, Duanlin

2006-12-01

The thermal stability of the denuded zone (DZ) created by high-low-high-temperature annealing in high carbon content (H[C]) and low carbon content (L[C]) Czochralski silicon (Cz-Si) has been investigated in a subsequent ramping and isothermal 1050 °C annealing. The tiny oxygen precipitates which might occur in the DZ were checked. It was found in the L[C] Cz-Si that the DZ shrank and the density of bulk micro-defects (BMDs) reduced with the increase of time spent at 1050 °C. Also, the DZs above 15 µm of thickness present in the H[C] Cz-Si wafers continuously and the density and total volume of BMDs first decreased then increased and finally decreased again during the treatments. Moreover, tiny oxygen precipitates were hardly generated inside the DZs, indicating that H[C] Cz-Si wafers could support the fabrication of integrated circuits.

Improving the treatment of non-aqueous phase TCE in low permeability zones with permanganate.

Science.gov (United States)

Chokejaroenrat, Chanat; Comfort, Steve; Sakulthaew, Chainarong; Dvorak, Bruce

2014-03-15

Treating dense non-aqueous phase liquids (DNAPLs) embedded in low permeability zones (LPZs) is a particularly challenging issue for injection-based remedial treatments. Our objective was to improve the sweeping efficiency of permanganate (MnO4(-)) into LPZs to treat high concentrations of TCE. This was accomplished by conducting transport experiments that quantified the penetration of various permanganate flooding solutions into a LPZ that was spiked with non-aqueous phase (14)C-TCE. The treatments we evaluated included permanganate paired with: (i) a shear-thinning polymer (xanthan); (ii) stabilization aids that minimized MnO2 rind formation and (iii) a phase-transfer catalyst. In addition, we quantified the ability of these flooding solutions to improve TCE destruction under batch conditions by developing miniature LPZ cylinders that were spiked with (14)C-TCE. Transport experiments showed that MnO4(-) alone was inefficient in penetrating the LPZ and reacting with non-aqueous phase TCE, due to a distinct and large MnO2 rind that inhibited the TCE from further oxidant contact. By including xanthan with MnO4(-), the sweeping efficiency increased (90%) but rind formation was still evident. By including the stabilization aid, sodium hexametaphosphate (SHMP) with xanthan, permanganate penetrated 100% of the LPZ, no rind was observed, and the percentage of TCE oxidized increased. Batch experiments using LPZ cylinders allowed longer contact times between the flooding solutions and the DNAPL and results showed that SHMP+MnO4(-) improved TCE destruction by ∼16% over MnO4(-) alone (56.5% vs. 40.1%). These results support combining permanganate with SHMP or SHMP and xanthan as a means of treating high concentrations of TCE in low permeable zones. Copyright © 2014 Elsevier B.V. All rights reserved.

The influence of fuel-air swirl intensity on flame structures of syngas swirl-stabilized diffusion flame

Science.gov (United States)

Shao, Weiwei; Xiong, Yan; Mu, Kejin; Zhang, Zhedian; Wang, Yue; Xiao, Yunhan

2010-06-01

Flame structures of a syngas swirl-stabilized diffusion flame in a model combustor were measured using the OH-PLIF method under different fuel and air swirl intensity. The flame operated under atmospheric pressure with air and a typical low heating-value syngas with a composition of 28.5% CO, 22.5% H2 and 49% N2 at a thermal power of 34 kW. Results indicate that increasing the air swirl intensity with the same fuel, swirl intensity flame structures showed little difference except a small reduction of flame length; but also, with the same air swirl intensity, fuel swirl intensity showed great influence on flame shape, length and reaction zone distribution. Therefore, compared with air swirl intensity, fuel swirl intensity appeared a key effect on the flame structure for the model combustor. Instantaneous OH-PLIF images showed that three distinct typical structures with an obvious difference of reaction zone distribution were found at low swirl intensity, while a much compacter flame structure with a single, stable and uniform reaction zone distribution was found at large fuel-air swirl intensity. It means that larger swirl intensity leads to efficient, stable combustion of the syngas diffusion flame.

High exhaust temperature, zoned, electrically-heated particulate matter filter

Science.gov (United States)

Gonze, Eugene V.; Paratore, Jr., Michael J.; Bhatia, Garima

2015-09-22

A system includes a particulate matter (PM) filter, an electric heater, and a control circuit. The electric heater includes multiple zones, which each correspond to longitudinal zones along a length of the PM filter. A first zone includes multiple discontinuous sub-zones. The control circuit determines whether regeneration is needed based on an estimated level of loading of the PM filter and an exhaust flow rate. In response to a determination that regeneration is needed, the control circuit: controls an operating parameter of an engine to increase an exhaust temperature to a first temperature during a first period; after the first period, activates the first zone; deactivates the first zone in response to a minimum filter face temperature being reached; subsequent to deactivating the first zone, activates a second zone; and deactivates the second zone in response to the minimum filter face temperature being reached.

77 FR 38484 - Safety Zones; Annual Fireworks Events in the Captain of the Port Detroit Zone

Science.gov (United States)

2012-06-28

... zone will be enforced from 10:00 p.m. to 11:00 p.m. on July 5, 2012. (8) Grosse Isle Yacht Club.... (16) Grosse Pointe Yacht Club 4th of July Fireworks, Grosse Pointe Shores, MI. The safety zone listed...

Fabrication techniques of X-ray spiral zone plates

International Nuclear Information System (INIS)

Gao Nan; Zhu Xiaoli; Li Hailiang; Xie Changqing

2010-01-01

The techniques to make X-ray spiral zone plates using electron beam and X-ray lithography were studied. A master mask was fabricated on polyimide membrane by E-beam lithography and micro-electroplating. Spiral zone plates were efficiently replicated by X-ray lithography and micro-electroplating. By combining the techniques, spiral zone plates at 1 keV were successfully fabricate. With an outermost zone width of the 200 nm, and the gold absorbers thickness of 700 nm, the high quality zone plates can be used for X-ray phase contrast microscopy.(authors)

United States Stateplane Zones - NAD83

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — U.S. State Plane Zones (NAD 1983) represents the State Plane Coordinate System (SPCS) Zones for the 1983 North American Datum within United States.

United States Stateplane Zones - NAD27

Data.gov (United States)

Earth Data Analysis Center, University of New Mexico — U.S. State Plane Zones (NAD 1927) represents the State Plane Coordinate System (SPCS) Zones for the 1927 North American Datum within United States.

Zone Denmark - gasell Taanist / Reet Krause

Index Scriptorium Estoniae

Krause, Reet, 1967-

2006-01-01

Taanis Viborgis asuva firma Zone Company Denmark, kaubamärgi Zone Denmark ja firma disainerite tutvustus. Ettevõte valmistab disainitooteid roostevabast terasest, klaasist, puidust, kummist jm. Disainer Naja Utzon Popov endast, oma loomingust

U Plant Geographic Zone Cleanup Prototype

International Nuclear Information System (INIS)

Romine, L.D.; Leary, K.D.; Lackey, M.B.; Robertson, J.R.

2006-01-01

The U Plant geographic zone (UPZ) occupies 0.83 square kilometers on the Hanford Site Central Plateau (200 Area). It encompasses the U Plant canyon (221-U Facility), ancillary facilities that supported the canyon, soil waste sites, and underground pipelines. The UPZ cleanup initiative coordinates the cleanup of the major facilities, ancillary facilities, waste sites, and contaminated pipelines (collectively identified as 'cleanup items') within the geographic zone. The UPZ was selected as a geographic cleanup zone prototype for resolving regulatory, technical, and stakeholder issues and demonstrating cleanup methods for several reasons: most of the area is inactive, sufficient characterization information is available to support decisions, cleanup of the high-risk waste sites will help protect the groundwater, and the zone contains a representative cross-section of the types of cleanup actions that will be required in other geographic zones. The UPZ cleanup demonstrates the first of 22 integrated zone cleanup actions on the Hanford Site Central Plateau to address threats to groundwater, the environment, and human health. The UPZ contains more than 100 individual cleanup items. Cleanup actions in the zone will be undertaken using multiple regulatory processes and decision documents. Cleanup actions will include building demolition, waste site and pipeline excavation, and the construction of multiple, large engineered barriers. In some cases, different cleanup actions may be taken at item locations that are immediately adjacent to each other. The cleanup planning and field activities for each cleanup item must be undertaken in a coordinated and cohesive manner to ensure effective execution of the UPZ cleanup initiative. The UPZ zone cleanup implementation plan (ZCIP) [1] was developed to address the need for a fundamental integration tool for UPZ cleanup. As UPZ cleanup planning and implementation moves forward, the ZCIP is intended to be a living document that will

Restoring ecosystem services to littoral zones of rivers in the urban core of Chongqing, China.

Science.gov (United States)

Xian, Xu-Dong; Feng, Yi-Long; Willison, J H Martin; Ai, Li-Jiao; Wang, Ping; Wu, Zhi-Neng

2015-08-01

Two examples of the creation of naturalized areas in the littoral zone of the Three Gorges Reservoir in the urban core of Chongqing City, China, are described. The areas were created for the purpose of restoring ecological functions and services. Plants were selected based on surveys of natural wetland vegetation in the region, and experiments were conducted to discover the capacity of species of interest to survive the sometimes extreme hydrological regimes at the sites. Novel methods were developed to stabilize the plants against the rigors of extreme summer floods and constant swash, notably zigzag berms of rocks wrapped in iron mesh. The areas include native reeds, grasses, shrubs, and trees. Plant communities in the areas are zoned according to flooding stress, and their structure is less stable at lower elevations that are subjected to greater stress. The tall grass Saccharum spontaneum (widespread in Southern Asia) and the tree Pterocarya stenoptera (native to Southwest China) are notable for their utility at these sites in the center of a large city. Communities of tall reeds and grasses have become so dense and stable that they now provide the ecosystem services of capturing river sediments and resisting erosion of the river banks. It is recommended that extensive greening of the riparian zones in urban areas of the Three Gorges Reservoir be conducted for the purpose of providing ecosystem services, based in part on the experiences described here.

Problems of Chernobyl exclusion zone

International Nuclear Information System (INIS)

1996-01-01

The collection comprises the results of researches and design activity in the ChNPP exclusion zone with the aim to develop technology, equipment and instruments for RAW management and accident clean-up, studying of the composition and structure of the activity solid bearers in the soil of the exclusion zone and transformation of the radionuclides in the nearest zone of ChNPP. Much attention is paid to medical and biological problems of the accident influence on the flora, fauna and people's health, labour conditions and incidence of the people involved. The collection comprises the information for scientists, experts, postgraduates and students in gaged in ecology, radioecology, nuclear engineering, radiology, radiochemistry and radiobiology

Standardized precipitation index zones for Mexico

Energy Technology Data Exchange (ETDEWEB)

Giddings, L.; Soto, M. [Instituto de Ecologia, A.C., Xalapa, Veracruz (Mexico); Rutherford, B.M.; Maarouf, A. [Faculty of Environmental Studies, York University, Toronto, Ontario (Canada)

2005-01-01

Precipitation zone systems exists for Mexico based on seasonality, quantity of precipitation, climates and geographical divisions, but none are convenient for the study of the relation of precipitation with phenomena such as El nino. An empirical set of seven exclusively Mexican and six shared zones was derived from three series of Standardized Precipitation Index (SPI) images, from 1940 through 1989: a whole year series (SPI-12) of 582 monthly images, a six month series (SPI-6) of 50 images for winter months (November through April), and a six month series (SPI-6) of 50 images for summer months (May through October). By examination of principal component and unsupervised classification images, it was found that all three series had similar zones. A set of basic training fields chosen from the principal component images was used to classify all three series. The resulting thirteen zones, presented in this article, were found to be approximately similar, varying principally at zones edges. A set of simple zones defined by just a few vertices can be used for practical operations. In general the SPI zones are homogeneous, with almost no mixture of zones and few outliers of one zone in the area of others. They are compared with a previously published map of climatic regions. Potential applications for SPI zones are discussed. [Spanish] Existen varios sistemas de zonificacion de Mexico basados en la estacionalidad, cantidad de precipitacion, climas y divisiones geograficas, pero ninguno es conveniente para el estudio de la relacion de la precipitacion con fenomenos tales como El Nino. En este trabajo se presenta un conjunto de siete zonas empiricas exclusivamente mexicanas y seis compartidas, derivadas de tres series de imagenes de SPI (Indice Estandarizado de la Precipitacion), desde 1940 a 1989: una serie de 582 imagenes mensuales (SPI-12), una series de 50 imagenes (SPI-6) de meses de invierno (noviembre a abril), y otra de 50 imagenes (SPI-6) de meses de verano

Preface: Research advances in vadose zone hydrology through simulations with the TOUGH codes

International Nuclear Information System (INIS)

Finsterle, Stefan; Oldenburg, Curtis M.

2004-01-01

symposium, with special attention to issues related to the vadose zone and unsaturated flow systems. The first paper, written by the original developer of TOUGH, Karsten Pruess, provides an overview of the history of the TOUGH codes, the main physical processes considered, their mathematical and numerical implementation, and case studies. That paper is followed by a review article summarizing inverse modeling applications performed by iTOUGH2. A subsequent group of papers deals with diverse unsaturated zone systems, highlighting the versatility of the code to handle a variety of processes in different geologic settings. Simulation capabilities of the TOUGH codes are increasingly used for geologic carbon sequestration studies as testified by the next group of papers. The final series of papers demonstrates the use of the TOUGH codes in support of remediation and engineering applications. These studies discuss biological and reactive chemical transport simulations, the design of clean-up operations and landfill management, and the analysis of engineered soil stabilization. As guest editors, we thank the authors for their interesting contributions, and the many reviewers for their careful and constructive review comments. Finally, on behalf of all of the authors and ourselves, we express our sincerest appreciation to Rien van Genuchten for providing the opportunity to publish these papers together in a Special Section of ''Vadose Zone Journal''

Optimal exploration target zones

CSIR Research Space (South Africa)

Debba, Pravesh

2008-09-01

Full Text Available -of-evidence (WofE) method logistic regression canonical favorability analysis neural networks evidential belief functions Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote Sensing Background and Objective of the study... for the following equation: n∑ i=r ( n i ) pi(1− p)n−i = 0.95 . (1) Optimal Exploration Target Zones Debba, Carranza, Stein, van der Meer Introduction to Remote Sensing Background and Objective of the study Methodology Results METHODS (cont. . . ): FITNESS FUNCTION...

System zones in capillary zone electrophoresis: Moving boundaries caused by freely migrating hydrogen ions

Czech Academy of Sciences Publication Activity Database

Beckers, J. L.; Boček, Petr

2005-01-01

Roč. 26, č. 2 (2005), s. 446-452 ISSN 0173-0835 R&D Projects: GA ČR(CZ) GA203/02/0023; GA AV ČR(CZ) IAA4031401; GA AV ČR(CZ) IAA4031103 Institutional research plan: CEZ:AV0Z40310501 Keywords : capillary zone electrophoresis * system zone s Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 3.850, year: 2005

Spectral zone selection methodology for pebble bed reactors

International Nuclear Information System (INIS)

Mphahlele, Ramatsemela; Ougouag, Abderrafi M.; Ivanov, Kostadin N.; Gougar, Hans D.

2011-01-01

A methodology is developed for determining boundaries of spectral zones for pebble bed reactors. A spectral zone is defined as a region made up of a number of nodes whose characteristics are collectively similar and that are assigned the same few-group diffusion constants. The spectral zones are selected in such a manner that the difference (error) between the reference transport solution and the diffusion code solution takes a minimum value. This is achieved by choosing spectral zones through optimally minimizing this error. The objective function for the optimization algorithm is the total reaction rate error, which is defined as the sum of the leakage, absorption and fission reaction rates errors in each zone. The selection of these spectral zones is such that the core calculation results based on diffusion theory are within an acceptable tolerance as compared to a proper transport reference solution. Through this work, a consistent approach for identifying spectral zones that yield more accurate diffusion results is introduced.

ZONES OF STEADY CAPACITOR EXCITATION IN A MODE OF GENERATION OF TYPICAL ASYNCHRONOUS MACHINES

Directory of Open Access Journals (Sweden)

Postoronca Sv.

2009-12-01

Full Text Available In work some features of a mode of capacitor excitation of industrial asynchronous electric motors, and also generators made on their base which can be used in wind installations of low power are considered. Borders of zones of steady capacitor excitation of asynchronous electric motors in rated power of 0,25-22,0 kW and generators made on their base, and also character of influence of own losses and active capacity of loading of the equivalent circuit of the asynchronous machine resulted in parameters have been determined. Some recommendations after maintenance of stability of capacitor excitation of asynchronous machines for work in a mode of generation of electric energy are given.

33 CFR 165.103 - Safety and Security Zones; LPG Vessel Transits in Portland, Maine, Captain of the Port Zone...

Science.gov (United States)

2010-07-01

... within a 500-yard radius of any Liquefied Petroleum Gas (LPG) vessel while it is moored at the LPG... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety and Security Zones; LPG... and Security Zones; LPG Vessel Transits in Portland, Maine, Captain of the Port Zone, Portsmouth...

Saturated Zone Colloid-Facilitated Transport

International Nuclear Information System (INIS)

Wolfsberg, A.; Reimus, P.

2001-01-01

The purpose of the Saturated Zone Colloid-Facilitated Transport Analysis and Modeling Report (AMR), as outlined in its Work Direction and Planning Document (CRWMS MandO 1999a), is to provide retardation factors for colloids with irreversibly-attached radionuclides, such as plutonium, in the saturated zone (SZ) between their point of entrance from the unsaturated zone (UZ) and downgradient compliance points. Although it is not exclusive to any particular radionuclide release scenario, this AMR especially addresses those scenarios pertaining to evidence from waste degradation experiments, which indicate that plutonium and perhaps other radionuclides may be irreversibly attached to colloids. This report establishes the requirements and elements of the design of a methodology for calculating colloid transport in the saturated zone at Yucca Mountain. In previous Total Systems Performance Assessment (TSPA) analyses, radionuclide-bearing colloids were assumed to be unretarded in their migration. Field experiments in fractured tuff at Yucca Mountain and in porous media at other sites indicate that colloids may, in fact, experience retardation relative to the mean pore-water velocity, suggesting that contaminants associated with colloids should also experience some retardation. Therefore, this analysis incorporates field data where available and a theoretical framework when site-specific data are not available for estimating plausible ranges of retardation factors in both saturated fractured tuff and saturated alluvium. The distribution of retardation factors for tuff and alluvium are developed in a form consistent with the Performance Assessment (PA) analysis framework for simulating radionuclide transport in the saturated zone. To improve on the work performed so far for the saturated-zone flow and transport modeling, concerted effort has been made in quantifying colloid retardation factors in both fractured tuff and alluvium. The fractured tuff analysis used recent data

SMAS Fusion Zones Determine the Subfascial and Subcutaneous Anatomy of the Human Face: Fascial Spaces, Fat Compartments, and Models of Facial Aging.

Science.gov (United States)

Pessa, Joel E

2016-05-01

Fusion zones between superficial fascia and deep fascia have been recognized by surgical anatomists since 1938. Anatomical dissection performed by the author suggested that additional superficial fascia fusion zones exist. A study was performed to evaluate and define fusion zones between the superficial and the deep fascia. Dissection of fresh and minimally preserved cadavers was performed using the accepted technique for defining anatomic spaces: dye injection combined with cross-sectional anatomical dissection. This study identified bilaminar membranes traveling from deep to superficial fascia at consistent locations in all specimens. These membranes exist as fusion zones between superficial and deep fascia, and are referred to as SMAS fusion zones. Nerves, blood vessels and lymphatics transition between the deep and superficial fascia of the face by traveling along and within these membranes, a construct that provides stability and minimizes shear. Bilaminar subfascial membranes continue into the subcutaneous tissues as unilaminar septa on their way to skin. This three-dimensional lattice of interlocking horizontal, vertical, and oblique membranes defines the anatomic boundaries of the fascial spaces as well as the deep and superficial fat compartments of the face. This information facilitates accurate volume augmentation; helps to avoid facial nerve injury; and provides the conceptual basis for understanding jowls as a manifestation of enlargement of the buccal space that occurs with age. © 2016 The American Society for Aesthetic Plastic Surgery, Inc. Reprints and permission: journals.permissions@oup.com.

Calcium-dependent depletion zones in the cortical microtubule array coincide with sites of, but do not regulate, wall ingrowth papillae deposition in epidermal transfer cells.

Science.gov (United States)

Zhang, Hui-ming; Talbot, Mark J; McCurdy, David W; Patrick, John W; Offler, Christina E

2015-09-01

Trans-differentiation to a transfer-cell morphology is characterized by the localized deposition of wall ingrowth papillae that protrude into the cytosol. Whether the cortical microtubule array directs wall ingrowth papillae formation was investigated using a Vicia faba cotyledon culture system in which their adaxial epidermal cells were spontaneously induced to trans-differentiate to transfer cells. During deposition of wall ingrowth papillae, the aligned cortical microtubule arrays in precursor epidermal cells were reorganized into a randomized array characterized by circular depletion zones. Concurrence of the temporal appearance, spatial pattern, and size of depletion zones and wall ingrowth papillae was consistent with each papilla occupying a depletion zone. Surprisingly, microtubules appeared not to regulate construction of wall ingrowth papillae, as neither depolymerization nor stabilization of cortical microtubules changed their deposition pattern or morphology. Moreover, the size and spatial pattern of depletion zones was unaltered when the formation of wall ingrowth papillae was blocked by inhibiting cellulose biosynthesis. In contrast, the depletion zones were absent when the cytosolic calcium plumes, responsible for directing wall ingrowth papillae formation, were blocked or dissipated. Thus, we conclude that the depletion zones within the cortical microtubule array result from localized depolymerization of microtubules initiated by elevated cytosolic Ca(2+) levels at loci where wall ingrowth papillae are deposited. The physiological significance of the depletion zones as a mechanism to accommodate the construction of wall ingrowth papillae without compromising maintenance of the plasma membrane-microtubule inter-relationship is discussed. © The Author 2015. Published by Oxford University Press on behalf of the Society for Experimental Biology.

Geometry of the Aegean Benioff zones

Directory of Open Access Journals (Sweden)

M. Knapmeyer

1999-06-01

Full Text Available The morphology of the Aegean Benioff zone was reconstructed using 1366 hypocentres from the PDE catalogue 1973-1997. Two such zones are identified under the Aegean area, a large one (Main Aegean Subduction, MAS spanning the whole Hellenic arc and a smaller and younger one under the Western Peloponnesus. The geometry of the MAS suggests that it blocks its own subduction and, therefore, causes the development of the smaller western zone as a result of a step back process in the Pliocene.

The habitable zone and extreme planetary orbits.

Science.gov (United States)

Kane, Stephen R; Gelino, Dawn M

2012-10-01

The habitable zone for a given star describes the range of circumstellar distances from the star within which a planet could have liquid water on its surface, which depends upon the stellar properties. Here we describe the development of the habitable zone concept, its application to our own solar system, and its subsequent application to exoplanetary systems. We further apply this to planets in extreme eccentric orbits and show how they may still retain life-bearing properties depending upon the percentage of the total orbit which is spent within the habitable zone. Key Words: Extrasolar planets-Habitable zone-Astrobiology.

Focused Fluid Flow along Convergent Plate Boundaries - Deriving Flow Rates along Faults from Local Upwarping of the Base of the Gas Hydrate Stability Zone

Science.gov (United States)

Kunath, P.; Chi, W. C.; Liu, C. S.

2017-12-01

Convergent plate boundaries provide the ideal opportunity to examine the interactions of deformation, fluid flow and gas hydrate stability. However, there are still processes and parameters that remain unclear or scarce. This may be in part due to the fact that in situ determination of fluid flow rate is very difficult. Here, we present a newly developed 2-D hydrothermal model for (1) simulating the steady state, thermal effect of forced heat advection along a thin and shallow dipping fault and (2) quantifying fluid velocities required to deliver a thermal anomalies manifested at the bottom-simulating reflector (BSR) at its intersection with the fault zone. Assuming the horizontal thermal conduction is negligible, we derive our model using only a few crucial parameters: (a) the thermal conductivity structure between seafloor and fault; (b) the temperature at BSR depth and the seafloor; (c) fluid flow rate; (d) geometry of the fault conduit, including depth and thickness. Temperature disturbance is then described as a function of Peclet number and of the dip of the fault. Application of our model to Site 892 at Cascadia accretionary wedge (ODP Leg 146), where borehole data provide excellent thermal constraints on the hydrology, shows consistent results. By comparing the temperatures derived at the BSRs with the temperature field of our model, the results demonstrate that the temperature discrepancy is about 0 - 0.5 oC. We propose that this simple approach can provide, on the basis of a few parameters, rough estimate of the disturbance of the temperature caused by advecting fluid. Localized lateral BSR-based heat flow variations have been observed near thrust faults along many convergent plate boundaries around the world and are associated with strong localized fluid flow. We wish to further testing this approach using other seismic datasets to estimate first order of magnitude fluid migration patterns in other convergent boundaries.

76 FR 38077 - Special Local Regulations and Safety Zones; Recurring Events in Captain of the Port New York Zone

Science.gov (United States)

2011-06-29

...: All Zone. waters of Long Island Sound in an area bound by the following points: 40[deg]51'43.5'' N 073... Zone. located in approximate position 40[deg]51'52'' N 073[deg]56'24'' W (NAD 1983), approximately 1750...] RIN 1625-AA00; 1625-AA08 Special Local Regulations and Safety Zones; Recurring Events in Captain of...

49 CFR 222.41 - How does this rule affect Pre-Rule Quiet Zones and Pre-Rule Partial Quiet Zones?

Science.gov (United States)

2010-10-01

...-Rule Quiet Zone may be established by automatic approval and remain in effect, subject to § 222.51, if... Zone may be established by automatic approval and remain in effect, subject to § 222.51, if the Pre... 49 Transportation 4 2010-10-01 2010-10-01 false How does this rule affect Pre-Rule Quiet Zones and...

Study of the thermo-electronic stability of LTS conductors and contribution to the study of the thermo-electric stability of HTS conductors. Novel techniques to simulate quench precursors in superconducting electro-magnets

International Nuclear Information System (INIS)

Trillaud, F.

2005-09-01

Most of this work deals with the development of new heater technology to simulate quench precursors in super-conducting electro-magnets. The carbon paste point heater and 2 alternative technologies have been used: induction coils and the diode laser. 2 main experimental setups with 2 different heaters have been used to study the stability of Cu/NbTi composite wires. The order of magnitude of the results obtained with the charged point heater and the diode laser is consistent. Our work covered both low critical temperature (LTS) conductors and high critical temperature (HTS) conductors. A large body of data has been gathered on quench energies and normal zone propagation velocities (NZPV). Concerning quench energy: LTS conductors appear largely more sensitive to heat disturbances than HTS conductors. NZPV enables one to define the criteria for which a magnet can be considered as self-protected. It is commonly assumed that, below 1 m/s, active protection is necessary to ensure safe quenches. This is the case for HTS conductors whose NZPV is of the order of a few centimeters per seconds, at most. However, the NZPVs of LTS conductors are above a few meters per seconds. While HTS conductors can suffer from local hot spots which diffuse slowly resulting in damaging overheating, LTS conductors spread the normal zone quickly enough owing to their good thermal conductivity to minimize local overheating. In addition, this gives enough time to dump the energy of the magnet. This work clears a new path to carry out accurate and reproducible experiment on superconductors. It demonstrates the powerfulness of diode laser technology for stability studies. Numerical simulations of the thermal behaviour of a Cu/NbTi multi-filament composite wire have been performed, they are based on a simplified transient liquid helium heat exchange model. This model appears to be not accurate enough to simulate the early time evolution of the voltage between the current sharing temperature and the

Risk-based zoning for urbanizing floodplains.

Science.gov (United States)

Porse, Erik

2014-01-01

Urban floodplain development brings economic benefits and enhanced flood risks. Rapidly growing cities must often balance the economic benefits and increased risks of floodplain settlement. Planning can provide multiple flood mitigation and environmental benefits by combining traditional structural measures such as levees, increasingly popular landscape and design features (green infrastructure), and non-structural measures such as zoning. Flexibility in both structural and non-structural options, including zoning procedures, can reduce flood risks. This paper presents a linear programming formulation to assess cost-effective urban floodplain development decisions that consider benefits and costs of development along with expected flood damages. It uses a probabilistic approach to identify combinations of land-use allocations (residential and commercial development, flood channels, distributed runoff management) and zoning regulations (development zones in channel) to maximize benefits. The model is applied to a floodplain planning analysis for an urbanizing region in the Baja Sur peninsula of Mexico. The analysis demonstrates how (1) economic benefits drive floodplain development, (2) flexible zoning can improve economic returns, and (3) cities can use landscapes, enhanced by technology and design, to manage floods. The framework can incorporate additional green infrastructure benefits, and bridges typical disciplinary gaps for planning and engineering.

Methylation patterns in marginal zone lymphoma.

Science.gov (United States)

Arribas, Alberto J; Bertoni, Francesco

Promoter DNA methylation is a major regulator of gene expression and transcription. The identification of methylation changes is important for understanding disease pathogenesis, for identifying prognostic markers and can drive novel therapeutic approaches. In this review we summarize the current knowledge regarding DNA methylation in MALT lymphoma, splenic marginal zone lymphoma, nodal marginal zone lymphoma. Despite important differences in the study design for different publications and the existence of a sole large and genome-wide methylation study for splenic marginal zone lymphoma, it is clear that DNA methylation plays an important role in marginal zone lymphomas, in which it contributes to the inactivation of tumor suppressors but also to the expression of genes sustaining tumor cell survival and proliferation. Existing preclinical data provide the rationale to target the methylation machinery in these disorders. Copyright © 2016 Elsevier Ltd. All rights reserved.

Width of surface rupture zone for thrust earthquakes: implications for earthquake fault zoning

Science.gov (United States)

Boncio, Paolo; Liberi, Francesca; Caldarella, Martina; Nurminen, Fiia-Charlotta

2018-01-01

The criteria for zoning the surface fault rupture hazard (SFRH) along thrust faults are defined by analysing the characteristics of the areas of coseismic surface faulting in thrust earthquakes. Normal and strike-slip faults have been deeply studied by other authors concerning the SFRH, while thrust faults have not been studied with comparable attention. Surface faulting data were compiled for 11 well-studied historic thrust earthquakes occurred globally (5.4 ≤ M ≤ 7.9). Several different types of coseismic fault scarps characterize the analysed earthquakes, depending on the topography, fault geometry and near-surface materials (simple and hanging wall collapse scarps, pressure ridges, fold scarps and thrust or pressure ridges with bending-moment or flexural-slip fault ruptures due to large-scale folding). For all the earthquakes, the distance of distributed ruptures from the principal fault rupture (r) and the width of the rupture zone (WRZ) were compiled directly from the literature or measured systematically in GIS-georeferenced published maps. Overall, surface ruptures can occur up to large distances from the main fault ( ˜ 2150 m on the footwall and ˜ 3100 m on the hanging wall). Most of the ruptures occur on the hanging wall, preferentially in the vicinity of the principal fault trace ( > ˜ 50 % at distances guidelines). In the absence of such a very detailed study (basic SM, i.e. Level 1 SM of Italian guidelines) a width of ˜ 840 m (90 % probability from "simple thrust" database of distributed ruptures, excluding B-M, F-S and Sy fault ruptures) is suggested to be sufficiently precautionary. For more detailed SM, where the fault is carefully mapped, one must consider that the highest SFRH is concentrated in a narrow zone, ˜ 60 m in width, that should be considered as a fault avoidance zone (more than one-third of the distributed ruptures are expected to occur within this zone). The fault rupture hazard zones should be asymmetric compared to the trace

Zone memories and pseudorandom addressing

International Nuclear Information System (INIS)

Marino, D.; Mirizzi, N.; Stella, R.; Visaggio, G.

1975-01-01

A quantitative comparison between zone memories, pseudorandom addressed memories and an alternative special purpose memory (spread zone memory) in which the distance between any two transformed descriptors, at first adjacent, is independent of the descriptors pair and results the maximum one is presented. This memory has not been particularly considered at present in spite of its efficiency and its simple implementation

Improving the effectiveness of smart work zone technologies.

Science.gov (United States)

2016-11-01

This project evaluates the effectiveness of sensor network systems for work zone traffic estimation. The comparative analysis is : performed on a work zone modeled in microsimulation and calibrated with field data from two Illinois work zones. Realis...

A relation between Liapunov stability, non-wanderingness and Poisson stability

International Nuclear Information System (INIS)

Ahmad, K.H.

1985-07-01

In this work, some of the relations among Liapunov stability, non-wanderingness and Poisson stability are considered. In particular it is shown that for a non-wandering point in a set, positive (resp. negative) Liapunov stability in that set implies positive (resp. negative) Poisson stability in the same set. (author)

Shear zones between rock units with no relative movement

DEFF Research Database (Denmark)

Koyi, Hemin; Schmeling, Harro; Burchardt, Steffi

2013-01-01

Shear zones are normally viewed as relatively narrow deformation zones that accommodate relative displacement between two "blocks" that have moved past each other in opposite directions. This study reports localized zones of shear between adjacent blocks that have not moved past each other. Such ...... given credit for and may be responsible for some reverse kinematics reported in shear zones....... or wakes, elongated bodies (vertical plates or horizontal rod-like bodies) produce tabular shear zones or wakes. Unlike conventional shear zones across which shear indicators usually display consistent symmetries, shear indicators on either side of the shear zone or wake reported here show reverse...... kinematics. Thus profiles exhibit shear zones with opposed senses of movement across their center-lines or -planes.We have used field observations and results from analytical and numerical models to suggest that examples of wakes are the transit paths that develop where denser blocks sink within salt...

The Development Evaluation of Economic Zones in China

Science.gov (United States)

Shi, Hong-Bo; Zhang, Zhe; Zhai, Yuming; Chen, Quan; Wang, Jiangtao

2018-01-01

After the Chinese reform and opening up, the construction of economic zones, such as Special Economic Zones, Hi-tech Zones and Bonded Zones, has played an irreplaceable role in China’s economic development. Currently, against the background of Chinese economic transition, research on development evaluation of economic zones has become popular and necessary. Similar research usually focuses on one specific field, and the methods that are used to evaluate it are simple. This research aims to analyse the development evaluation of zones by synthesis. A new hybrid multiple criteria decision making (MCDM) model that combines the DEMATEL technique and the DANP method is proposed. After establishing the evaluation criterion system and acquiring data, the influential weights of dimensions and criteria can be calculated, which will be a guide for forming measures of development. Shandong Peninsula Blue Economic Zone is used in the empirical case analysis. The results show that Transportation Conditions, Industrial Structure and Business Climate are the main influencing criteria and measures based on these criteria are proposed. PMID:29301304

Work Zone Intrusion Report Interface Design

Science.gov (United States)

2018-02-02

While necessary for roadways, work zones present a safety risk to crew. Half of road workers deaths between 2005 and 2010 were due to collisions with motorists intruding on the work zone. Therefore, addressing intrusions is an important step for ensu...

Work zone performance measures pilot test.

Science.gov (United States)

2011-04-01

Currently, a well-defined and validated set of metrics to use in monitoring work zone performance do not : exist. This pilot test was conducted to assist state DOTs in identifying what work zone performance : measures can and should be targeted, what...

FIGHT ZONE WITH POINTS OF THE SHOTOKAN KARATE FEMALE COMPETITION

Directory of Open Access Journals (Sweden)

Nelson Kautzner Marques Junior

2014-04-01

Full Text Available The objective of the study was to determine the fight zone with point during the female kumite of competition. This study used a quantitative research for identify the fight zone with point (ippon or waza-ari or not during the female kumite of competition. Were selected on the Internet several championship of kumite of the JKA and of the ITKF. The study detected a high probability of point in the zone 7 and in the zone 2. The study determined that the most points at the corner occurred when the karateka practiced the attack in fight zone. Kruskal-Wallis ANOVA verified significant difference between the fight zone with points, H (10 = 29,49, p = 0,001. The Mann Whitney U test detected significant difference between the zone 5 with waza-ari versus all the zone. The greatest number of points in the fight zone was in agreement with the size of the fight zone. The central zone or zone 5 has 6x6 m, during the female kumite occurred more points, total of 68 waza-aris and 5 ippons. The study on the fight zone with points of the female kumite permits that the karateka has knowledge about the combat zones and guides the karateka before, during and after the female kumite. However, more studies should be done to confirm these findings.

75 FR 16370 - Regulated Navigation Areas, Safety Zones, Security Zones; Deepwater Ports in Boston Captain of...

Science.gov (United States)

2010-04-01

... rule under Executive Order 13045, Protection of Children from Environmental Health Risks and Safety Risks. This rule is not an economically significant rule and would not create an environmental risk to...] RIN 1625-AA00, RIN 1625-AA11 Regulated Navigation Areas, Safety Zones, Security Zones; Deepwater Ports...

Width of surface rupture zone for thrust earthquakes: implications for earthquake fault zoning

Directory of Open Access Journals (Sweden)

P. Boncio

2018-01-01

Full Text Available The criteria for zoning the surface fault rupture hazard (SFRH along thrust faults are defined by analysing the characteristics of the areas of coseismic surface faulting in thrust earthquakes. Normal and strike–slip faults have been deeply studied by other authors concerning the SFRH, while thrust faults have not been studied with comparable attention. Surface faulting data were compiled for 11 well-studied historic thrust earthquakes occurred globally (5.4 ≤ M ≤ 7.9. Several different types of coseismic fault scarps characterize the analysed earthquakes, depending on the topography, fault geometry and near-surface materials (simple and hanging wall collapse scarps, pressure ridges, fold scarps and thrust or pressure ridges with bending-moment or flexural-slip fault ruptures due to large-scale folding. For all the earthquakes, the distance of distributed ruptures from the principal fault rupture (r and the width of the rupture zone (WRZ were compiled directly from the literature or measured systematically in GIS-georeferenced published maps. Overall, surface ruptures can occur up to large distances from the main fault ( ∼ 2150 m on the footwall and  ∼  3100 m on the hanging wall. Most of the ruptures occur on the hanging wall, preferentially in the vicinity of the principal fault trace ( >   ∼  50 % at distances  <   ∼  250 m. The widest WRZ are recorded where sympathetic slip (Sy on distant faults occurs, and/or where bending-moment (B-M or flexural-slip (F-S fault ruptures, associated with large-scale folds (hundreds of metres to kilometres in wavelength, are present. A positive relation between the earthquake magnitude and the total WRZ is evident, while a clear correlation between the vertical displacement on the principal fault and the total WRZ is not found. The distribution of surface ruptures is fitted with probability density functions, in order to define a criterion to

Presynaptic Active Zone Density during Development and Synaptic Plasticity.

Science.gov (United States)

Clarke, Gwenaëlle L; Chen, Jie; Nishimune, Hiroshi

2012-01-01

Neural circuits transmit information through synapses, and the efficiency of synaptic transmission is closely related to the density of presynaptic active zones, where synaptic vesicles are released. The goal of this review is to highlight recent insights into the molecular mechanisms that control the number of active zones per presynaptic terminal (active zone density) during developmental and stimulus-dependent changes in synaptic efficacy. At the neuromuscular junctions (NMJs), the active zone density is preserved across species, remains constant during development, and is the same between synapses with different activities. However, the NMJ active zones are not always stable, as exemplified by the change in active zone density during acute experimental manipulation or as a result of aging. Therefore, a mechanism must exist to maintain its density. In the central nervous system (CNS), active zones have restricted maximal size, exist in multiple numbers in larger presynaptic terminals, and maintain a constant density during development. These findings suggest that active zone density in the CNS is also controlled. However, in contrast to the NMJ, active zone density in the CNS can also be increased, as observed in hippocampal synapses in response to synaptic plasticity. Although the numbers of known active zone proteins and protein interactions have increased, less is known about the mechanism that controls the number or spacing of active zones. The following molecules are known to control active zone density and will be discussed herein: extracellular matrix laminins and voltage-dependent calcium channels, amyloid precursor proteins, the small GTPase Rab3, an endocytosis mechanism including synaptojanin, cytoskeleton protein spectrins and β-adducin, and a presynaptic web including spectrins. The molecular mechanisms that organize the active zone density are just beginning to be elucidated.

Zones of emotional labour

DEFF Research Database (Denmark)

Strøbæk, Pernille Solveig

2011-01-01

The paper suggests that due to the difficult nature of their work public family law caseworkers are to be included in the definition of emotional labour even though they are omitted by Hochschild. Based upon a review of the structures involved in emotional labour an explorative qualitative study...... is put forth among 25 Danish public family law caseworkers. The study points to personal, professional, and social zones of emotional labour through which the caseworkers carry out their work. Emotional labour zones mark emotion structures that may be challenging due to complex emotional intersections...

Dike zones on Venus

Science.gov (United States)

Markov, M. S.; Sukhanov, A. L.

1987-01-01

Venusian dike zone structures were identified from Venera 15 and 16 radar images. These include: a zone of subparallel rows centered at 30 deg N, 7 deg E; a system of intersecting bands centered at 67 deg N, 284 deg E; polygonal systems in lavas covering the structural base uplift centered at 47 deg N, 200 deg E; a system of light bands in the region of the ring structure centered at 43 deg N, 13 deg E; and a dike band centered at 27 deg N, 36 deg E.

THEORETICAL CONSIDERATIONS OF PRICE STABILITY AS PART OF THE FINANCIAL STABILITY

Directory of Open Access Journals (Sweden)

Magdalena RĂDULESCU

2012-09-01

Full Text Available Currently there are many authors who consider that the only objective of the central bank should be the price stability and between the respective objective and financial stability there is incompatibility. As far we are concerned, we subscribe the idea that between price stability and financial stability there are complementarities. And a strong argument in the favour of this position is also historical. Actually, many older or newer facts show that banking crises were often caused by the unfavourable macroeconomic situation coupled with the bad macroeconomic policies carried by the authorities. But, a monetary policy that aims the price stability reduces this risk. The truth is that the central banks have a series of tools that allow them to act for achieving both the objective of price stability, and that of the stability of financial sector. Although the financial stability is not, usually, an explicit objective for the modern central bank, the systematic financial instability can cancel their performances in achieving their major final objective: the price stability. Being that, because of the need that it creates to inject additional liquidity into the banking system, a crisis of the banking sector may directly affect the monetary stability. Here the mentioned complementarities arise between price stability and financial stability, although the achievement of the first does not necessarily involve the assurance of the last.

Identification and adaptive neural network control of a DC motor system with dead-zone characteristics.

Science.gov (United States)

Peng, Jinzhu; Dubay, Rickey

2011-10-01

In this paper, an adaptive control approach based on the neural networks is presented to control a DC motor system with dead-zone characteristics (DZC), where two neural networks are proposed to formulate the traditional identification and control approaches. First, a Wiener-type neural network (WNN) is proposed to identify the motor DZC, which formulates the Wiener model with a linear dynamic block in cascade with a nonlinear static gain. Second, a feedforward neural network is proposed to formulate the traditional PID controller, termed as PID-type neural network (PIDNN), which is then used to control and compensate for the DZC. In this way, the DC motor system with DZC is identified by the WNN identifier, which provides model information to the PIDNN controller in order to make it adaptive. Back-propagation algorithms are used to train both neural networks. Also, stability and convergence analysis are conducted using the Lyapunov theorem. Finally, experiments on the DC motor system demonstrated accurate identification and good compensation for dead-zone with improved control performance over the conventional PID control. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

Long-term stability of sodium caseinate-stabilized nanoemulsions.

Science.gov (United States)

Yerramilli, Manispuritha; Ghosh, Supratim

2017-01-01

Oil-in-water (5 wt%) nanoemulsions were prepared with different concentration (2.5-10 wt%) of sodium caseinate as a sole emulsifier and their long-term storage stability was investigated for 6 months. Previous studies associated with sodium caseinate looked only into nanoemulsion formation; hence the challenges with long-term stability were not addressed. All nanoemulsions displayed an average droplet size sodium caseinate-stabilized nanoemulsions.

Subsurface Characterization using Geophysical Seismic Refraction Survey for Slope Stabilization Design with Soil Nailing

Science.gov (United States)

Ashraf Mohamad Ismail, Mohd; Ng, Soon Min; Hazreek Zainal Abidin, Mohd; Madun, Aziman

2018-04-01

The application of geophysical seismic refraction for slope stabilization design using soil nailing method was demonstrated in this study. The potential weak layer of the study area is first identify prior to determining the appropriate length and location of the soil nail. A total of 7 seismic refraction survey lines were conducted at the study area with standard procedures. The refraction data were then analyzed by using the Pickwin and Plotrefa computer software package to obtain the seismic velocity profiles distribution. These results were correlated with the complementary borehole data to interpret the subsurface profile of the study area. It has been identified that layer 1 to 3 is the potential weak zone susceptible to slope failure. Hence, soil nails should be installed to transfer the tensile load from the less stable layer 3 to the more stable layer 4. The soil-nail interaction will provide a reinforcing action to the soil mass thereby increasing the stability of the slope.

ZONE: a finite element mesh generator

International Nuclear Information System (INIS)

Burger, M.J.

1976-05-01

The ZONE computer program is a finite-element mesh generator which produces the nodes and element description of any two-dimensional geometry. The geometry is subdivided into a mesh of quadrilateral and triangular zones arranged sequentially in an ordered march through the geometry. The order of march can be chosen so that the minimum bandwidth is obtained. The node points are defined in terms of the x and y coordinates in a global rectangular coordinate system. The zones generated are quadrilaterals or triangles defined by four node points in a counterclockwise sequence. Node points defining the outside boundary are generated to describe pressure boundary conditions. The mesh that is generated can be used as input to any two-dimensional as well as any axisymmetrical structure program. The output from ZONE is essentially the input file to NAOS, HONDO, and other axisymmetric finite element programs. 14 figures

78 FR 11798 - Safety Zones; Annual Fireworks Events in the Captain of the Port Buffalo Zone

Science.gov (United States)

2013-02-20

... later notice in the Federal Register. B. Regulatory History and Information On June 18, 2008, the Coast... coordinates for the safety zones corresponding with the Browns Football Half time Fireworks and the Lorain... Football Half time and the Lorain Port Fest safety zones, to include changing the format of the coordinates...

77 FR 35852 - Safety Zones; Multiple Firework Displays in Captain of the Port, Puget Sound Zone

Science.gov (United States)

2012-06-15

... 13045, Protection of Children from Environmental Health Risks and Safety Risks. This rule is not an economically significant rule and does not create an environmental risk to health or risk to safety that may... 1625-AA00 Safety Zones; Multiple Firework Displays in Captain of the Port, Puget Sound Zone AGENCY...

77 FR 8219 - Coastal Zone Management Program: Illinois

Science.gov (United States)

2012-02-14

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration Coastal Zone Management... ICMP constitutes an approvable program and that requirements of the Coastal Zone Management Act (CZMA..., submitted a coastal management program to NOAA for approval under the Coastal Zone Management Act (CZMA), 16...

33 CFR 165.755 - Safety Zone; Guayanilla, Puerto Rico

Science.gov (United States)

2010-07-01

... Zone; Guayanilla, Puerto Rico (a) The following area is established as a safety zone during the... the Eco-Electrica waterfront facility in Guayanilla Bay, Puerto Rico. The safety zone remains in... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety Zone; Guayanilla, Puerto...

Deficiencies in Vadose Zone Understanding at the INEEL

Energy Technology Data Exchange (ETDEWEB)

Wood, Thomas Ronald; Bates, Dona Louise; Bishop, Carolyn Wagoner; Heard, Robert Eugene; Hubbell, Joel Michael; Hull, Laurence Charles; Lehman, Richard Michael; Magnuson, Swen O; Mattson, Earl Douglas; Mccarthy, James Michael; Porro, Indrek; Ritter, Paul David; Roddy, Michael Scott; Singler, Robert Edward; Smith, Richard Paul

2000-08-01

Subsurface contamination in the vadose zone, that portion of the subsurface pathway between land surface and an underlying aquifer, poses environmental problems at the Idaho National Engineering and Environmental Laboratory (INEEL) in eastern Idaho and across the U.S. Department of Energy complex. Assessing potential adverse impacts from these contaminated sites requires an understanding of the mechanisms controlling contaminant transport. Currently, vadose zone experts at the INEEL cannot with confidence predict the movement of water and contaminants in the complex, heterogeneous, fractured subsurface at the INEEL, especially within the vadose zone. In the draft version (Revision 1) of the Vadose Zone Deficiencies document, deficiencies in scientific understanding of flow and transport processes in the vadose zone at the INEEL were identified and grouped into 13 categories and recommendations were provided to address each of the deficiencies. The draft document provided the basis for an INEEL Vadose Zone Workshop that was conducted October 20 and 21, 1999, in Idaho Falls, Idaho. The workshop was conducted to group and rank the previously identified deficiencies and for the subsequent development of science plans to address the deficiencies that limit reliable predictions of water and contaminant movement in the subsurface. The workshop participants, comprising INEEL and scientists and project managers and non-INEEL scientists knowledgeable about the vadose zone, developed science- and technology-based recommendations derived through a series of technical sessions at the workshop. In this document, the final version of the Vadose Zone Deficiencies document, the draft document has been incorporated, largely intact, as well as the results from the workshop. The workshop participants grouped the deficiencies in vadose zone understanding at the INEEL into seven categories. These seven categories will be the focus areas of five science plans that are being developed to

Analysis of stability to cheaters in models of antibiotic degrading microbial communities.

Science.gov (United States)

Szilágyi, András; Boza, Gergely; Scheuring, István

2017-06-21

Antibiotic resistance carried out by antibiotic degradation has been suggested recently as a new mechanism to maintain coexistence of microbial species competing on a single limiting resource, even in well-mixed homogeneous environments. Species diversity and community stability, however, critically depend on resistance against social cheaters, mutants that do not invest in production, but still enjoy the benefits provided by others. Here we investigate how different mutant cheaters affect the stability of antibiotic producing and degrading microbial communities. We consider two cheater types, production and degradation cheaters. We generalize the mixed inhibition-zone and chemostat models introduced previously [Kelsic, E. D., Zhao, J., Vetsigian, K., Kishony, R., 2015. Counteraction of an tibiotic production and degradation stabilizes microbial communities. Nature521, 516-519.] to study the population dynamics of microbial communities in well-mixed environment, and analyze the invasion of different cheaters in these models. We show that production cheaters, mutants that cease producing antibiotics, always destroy coexistence whenever there is a cost of producing these antibiotics. Degradation cheaters, mutants that loose their function of producing extracellular antibiotic degrading molecules, induce community collapse only if the cost of producing the degradation factors is above a critical level. Our analytical studies, supported by numerical simulations, highlight the sensitivity of antibiotic producing and degrading communities to loss-of-function mutants. Copyright © 2017 Elsevier Ltd. All rights reserved.

Fifty years of shear zones

Science.gov (United States)

Graham, Rodney

2017-04-01

We are here, of course, because 1967 saw the publication of John Ramsay's famous book. Two years later a memorable field trip from Imperial College to the Outer Hebrides saw John on a bleak headland on the coast of North Uist where a relatively undeformed metadolerite within Lewisian (Precambrian) gneisses contained ductile shear zones with metamorphic fabrics in amphibolite facies. One particular outcrop was very special - a shear zone cutting otherwise completely isotropic, undeformed metadolerite, with an incremental foliation starting to develop at 45° to the deformation zone, and increasing in intensity as it approached the shear direction. Here was proof of the process of simple shear under ductile metamorphic conditions - the principles of simple shear outlined in John Ramsay's 1967 book clearly visible in nature, and verified by Ramsay's mathematical proofs in the eventual paper (Ramsay and Graham, 1970). Later work on the Lewisian on the mainland of Scotland, in South Harris, in Africa, and elsewhere applied Ramsay's simple shear principles more liberally, more imprecisely and on larger scale than at Caisteal Odair, but in retrospect it documented what seems now to be the generality of mid and lower crustal deformation. Deep seismic reflection data show us that on passive margins hyper-stretched continental crust (whether or not cloaked by Seaward Dipping Reflectors) seems to have collapsed onto the mantle. Crustal faults mostly sole out at or above the mantle - so the Moho is a detachment- an 'outer marginal detachment', if you like, and, of course, it must be a ductile shear. On non-volcanic margins this shear zone forms the first formed ocean floor before true sea floor spreading gets going to create real oceanic crust. Gianreto Manatschal, Marcel Lemoine and others realised that the serpentinites described in parts of the Alps are exposed remnants of this ductile shear zone. Associated ophicalcite breccias tell of sea floor exposure, while high

The Devils Mountain Fault zone: An active Cascadia upper plate zone of deformation, Pacific Northwest of North America

Science.gov (United States)

Barrie, J. Vaughn; Greene, H. Gary

2018-02-01

The Devils Mountain Fault Zone (DMFZ) extends east to west from Washington State to just south of Victoria, British Columbia, in the northern Strait of Juan de Fuca of Canada and the USA. Recently collected geophysical data were used to map this fault zone in detail, which show the main fault trace, and associated primary and secondary (conjugate) strands, and extensive northeast-southwest oriented folding that occurs within a 6 km wide deformation zone. The fault zone has been active in the Holocene as seen in the offset and disrupted upper Quaternary strata, seafloor displacement, and deformation within sediment cores taken close to the seafloor expression of the faults. Data suggest that the present DMFZ and the re-activated Leech River Fault may be part of the same fault system. Based on the length and previously estimated slip rates of the fault zone in Washington State, the DMFZ appears to have the potential of producing a strong earthquake, perhaps as large as magnitude 7.5 or greater, within 2 km of the city of Victoria.

A viscoplastic shear-zone model for deep (15-50 km) slow-slip events at plate convergent margins

Science.gov (United States)

Yin, An; Xie, Zhoumin; Meng, Lingsen

2018-06-01

A key issue in understanding the physics of deep (15-50 km) slow-slip events (D-SSE) at plate convergent margins is how their initially unstable motion becomes stabilized. Here we address this issue by quantifying a rate-strengthening mechanism using a viscoplastic shear-zone model inspired by recent advances in field observations and laboratory experiments. The well-established segmentation of slip modes in the downdip direction of a subduction shear zone allows discretization of an interseismic forearc system into the (1) frontal segment bounded by an interseismically locked megathrust, (2) middle segment bounded by episodically locked and unlocked viscoplastic shear zone, and (3) interior segment that slips freely. The three segments are assumed to be linked laterally by two springs that tighten with time, and the increasing elastic stress due to spring tightening eventually leads to plastic failure and initial viscous shear. This simplification leads to seven key model parameters that dictate a wide range of mechanical behaviors of an idealized convergent margin. Specifically, the viscoplastic rheology requires the initially unstable sliding to be terminated nearly instantaneously at a characteristic velocity, which is followed by stable sliding (i.e., slow-slip). The characteristic velocity, which is on the order of <10-7 m/s for the convergent margins examined in this study, depends on the (1) effective coefficient of friction, (2) thickness, (3) depth, and (4) viscosity of the viscoplastic shear zone. As viscosity decreases exponentially with temperature, our model predicts faster slow-slip rates, shorter slow-slip durations, more frequent slow-slip occurrences, and larger slow-slip magnitudes at warmer convergent margins.

76 FR 80342 - Coastal Zone Management Program: Illinois

Science.gov (United States)

2011-12-23

... DEPARTMENT OF COMMERCE National Oceanic and Atmospheric Administration Coastal Zone Management... program under the Coastal Zone Management Act (CZMA), as amended at 16 U.S.C. 1451-1466, and the...). SUPPLEMENTARY INFORMATION: The Coastal Zone Management Act authorizes the Secretary of Commerce (Secretary) to...

Resistive stability of the cylindrical spheromak

International Nuclear Information System (INIS)