Wavelength selection in the crown splash

Science.gov (United States)

Zhang, Li V.; Brunet, Philippe; Eggers, Jens; Deegan, Robert D.

2010-12-01

The impact of a drop onto a liquid layer produces a splash that results from the ejection and dissolution of one or more liquid sheets, which expand radially from the point of impact. In the crown splash parameter regime, secondary droplets appear at fairly regularly spaced intervals along the rim of the sheet. By performing many experiments for the same parameter values, we measure the spectrum of small-amplitude perturbations growing on the rim. We show that for a range of parameters in the crown splash regime, the generation of secondary droplets results from a Rayleigh-Plateau instability of the rim, whose shape is almost cylindrical. In our theoretical calculation, we include the time dependence of the base state. The remaining irregularity of the pattern is explained by the finite width of the Rayleigh-Plateau dispersion relation. Alternative mechanisms, such as the Rayleigh-Taylor instability, can be excluded for the experimental parameters of our study.

Drop splashing: the role of surface wettability and liquid viscosity

Science.gov (United States)

Almohammadi, Hamed; Amirfazli, Alidad; -Team

2017-11-01

There are seemingly contradictory results in the literature about the role of surface wettability and drop viscosity for the splashing behavior of a drop impacting onto a surface. Motivated by such issues, we conducted a systematic experimental study where splashing behavior for a wide range of the liquid viscosity (1-100 cSt) and surface wettability (hydrophilic to hydrophobic) are examined. The experiments were performed for the liquids with both low and high surface tensions ( 20 and 72 mN/m). We found that the wettability affects the splashing threshold at high or low contact angle values. At the same drop velocity, an increase of the viscosity (up to 4 cSt) promotes the splashing; while, beyond such value, any increase in viscosity shows the opposite effect. It is also found that at a particular combination of liquid surface tension and viscosity (e.g. silicone oil, 10 cSt), an increase in the drop velocity changes the splashing to spreading. We relate such behaviors to the thickness, shape, and the velocity of the drop's lamella. Finally, to predict the splashing, we developed an empirical correlation which covers all of the previous reported data, hence clarifying the ostensible existing contradictions.

Water Quality Survey of Splash Pads After A Waterborne Salmonellosis Outbreak--Tennessee, 2014.

Science.gov (United States)

Clayton, Joshua L; Manners, Judy; Miller, Susan; Shepherd, Craig; Dunn, John R; Schaffner, William; Jones, Timothy F

2017-06-01

Waterborne outbreaks of salmonellosis are uncommon. The Tennessee Department of Health investigated a salmonellosis outbreak of 10 cases with the only common risk factor being exposure to a single splash pad. Risks included water splashed in the face at the splash pad and no free residual chlorine in the water system. We surveyed water quality and patron behaviors at splash pads statewide. Of the 29 splash pads participating in the water quality survey, 24 (83%) used a recirculating water system. Of the 24, 5 (21%) water samples were tested by polymerase chain reaction and found to be positive for E. coli, Giardia, norovirus, or Salmonella. Among 95 patrons observed, we identified common high-risk behaviors of sitting on the fountain or spray head and putting mouth to water. Water venue regulations and improved education of patrons are important to aid prevention efforts.

Partitioning washoff of manure-borne fecal indicators (Escherichia coli and stanols) into splash and hydraulic components: field rainfall simulations in a tropical agro-ecosystem.

Science.gov (United States)

Ribolzi, Olivier; Rochelle-Newall, Emma J.; Janeau, Jean-Louis; Viguier, Marion; Jardé, Emilie; Latsachack, Keooudone; Henri-Des-Tureaux, Thierry; Thammahacksac, Chanthamousone; Mugler, Claude; Valentin, Christian; Sengtaheuanghoung, Oloth

2017-04-01

Overland flow from manured fields and pastures is known to be an important mechanism by which organisms of faecal origin are transferred to streams in rural watersheds. In the tropical montane areas of South-East Asia, recent changes in land use have induced increased runoff, soil erosion, in-stream suspended sediment loads resulting in increased microbial pathogen dissemination and contamination of stream waters. The majority of enteric and environmental bacteria in aquatic systems are associated with particles such as sediments which can strongly influence their survival and transport characteristics. Escherichia coli (E. coli) has emerged as one of the most appropriate microbial indicators of faecal contamination of natural waters, with the presence of E. coli indicating that faecal contamination is present. In association with E. coli, faecal stanols can also be used as microbial source tracking tool for the identification of the origin of the faecal contamination (e.g. livestock, human, etc). Field rain simulations were used to examine how E.coli and stanols are exported from the surface of upland, agricultural soils during overland flow events. The objectives were to characterize the loss dynamics of these indicators from agricultural soils contaminated with livestock waste, and to partition total detachment into the splash and hydraulic components. Nine 1m2 microplots were divided in triplicated treatment groups: (a) controls with no amendments, (b) amended with pig manure or (c) poultry manure. Each plot was divided into two 0.5m2 rectangular subplots. For each simulation, one subplot was designated as a rain splash treatment; the other was covered with 2-mm grid size wire screen 10 cm above the soil surface to break the raindrops into fine droplets, thus drastically reducing their kinetic energy. E. coli concentrations in overland flow were estimated for both the attached and free living fractions and stanols were measured on the particulate matter washed

Roughness influence on human blood drop spreading and splashing

Science.gov (United States)

Smith, Fiona; Buntsma, Naomi; Brutin, David

2017-11-01

The impact behaviour of complex fluid droplets is a topic that has been extensively studied but with much debate. The Bloodstain Pattern Analysis (BPA) community is encountering this scientific problem with daily practical cases since they use bloodstains as evidence in crime scene reconstruction. We aim to provide fundamental explanations in the study of blood drip stains by investigating the influence of surface roughness and wettability on the splashing limit of droplets of blood, a non-Newtonian colloidal fluid. Droplets of blood impacting perpendicularly different surfaces at different velocities were recorded. The recordings were analysed as well as the surfaces characteristics in order to find an empirical solution since we found that roughness plays a major role in the threshold of the splashing/non-splashing behaviour of blood compared to the wettability. Moreover it appears that roughness alters the deformation of the drip stains. These observations are key in characterising features of drip stains with the impacting conditions, which would answer some forensic issues.

2D-SPLASH spectroscopy to determine the fat/water ratio in the muscle of the rotator cuff

International Nuclear Information System (INIS)

Koestler, H.; Kenn, W.; Huemmer, C.; Hahn, D.; Boehm, D.

2002-01-01

Aim: The degree of fatty infiltration of the rotator cuff is an important factor for the prognosis of an operative reconstruction after rotator cuff tear. The aim of this work was to develop a method using a clinical MR scanner that allows the quantification of the fat/water ratio with the necessary spatial resolution. Method: A SPLASH sequence consisting of 19 complex 2D-FLASH images was implemented on a clinical 1.5 T MR scanner. The echo time was gradually increased from 5.0 ms to 50.0 ms. A spatial in plane resolution of 1.17 mm, a spectral resolution of 0.33 ppm and a spectral width of 6.25 ppm were achieved in a total acquisition time of about 3 min. The quantitative evaluation of the spectra in arbitrarily shaped regions of interest (ROIs) was obtained using a home-built reconstruction program and the time domain fit program AMARES. Results: Phantom studies show a linear relation of the concentration determined by SPLASH spectroscopy (r=0.997). Because of the high spatial resolution and the possibility to evaluate arbitrarily shaped ROIs, the determination of the fat/water ratio in single muscles in the shoulder has been possible. Conclusions: By the use of the 2D-SPLASH sequence the degree of fatty infiltration in the rotator cuff can now be determined quantitatively for the first time. (orig.) [de

Complexities of splashing

International Nuclear Information System (INIS)

Deegan, R D; Brunet, P; Eggers, J

2008-01-01

We study the impact of a drop of liquid onto a thin layer of the same liquid. We give an overview of the sequence of events that occur as the two most important dimensionless control parameters are varied. In particular, multiple cohorts of droplets can be ejected at different stages after impact due to different mechanisms. Edgerton's famous Milkdrop Coronet is only observed for a narrow range of parameters. Outside this range, the splash is either qualitatively different, or suffers from a much lower level of regularity. (cover illustration)

Effects of Fire on Soil Splash Erosion in Semi-steppe Rangelandof Karsanak Region,Chaharmahal and Bakhtiari

Directory of Open Access Journals (Sweden)

D. Baharlooi

2016-02-01

. Detachment rate is strongly influenced by soil properties, including soil texture and thickness of the water layer at the soil surface (De Ploey and Savat, 1968; Moss and Green, 1983; Sharma et al., 1991; Kinnell, 1991, Jomaa et al., 2010, soil strength, bulk density, cohesion, soil organic matter content, moisture content, infiltration capacity (Nearing et al., 1988; Owoputi, 1994; Morgan et al., 1998, Planchon et al., 2000, Ghahramani et al., 2011, soil initial water content, surface compaction and roughness (Planchon et al., 2000, the nature of soil aggregates and crust, porosity, capacity of ionic interchange, and clay content (Poesen and Torri, 1988. Several studies have shown that splash detachment rate is mainly related to surface rock fragments in soils with sparse vegetation cover (Jomaa et al., 2012. The present study was conducted to investigate the effects of fire on splash erosion and some erosion depended properties in semi-steppe rangeland of Karsanak region in Chaharmahal and Bakhtiari province which affected by man-made fire during 2008, 2009, 2010 and 2011. Materials and Methods: Soil samples were obtained on 2012 from the mentioned regions (8 samplesfrom the burned area and 8 samples as a control (unburned in the adjacent burned area from 0-7 cm depth. Splash erosion under simulated rainfall intensity of 2 mm per minute was measured using multivariate splash cup apparatus considering the slope of 5 and 25 degree. Soil pH, soil electrical conductivity, equivalent calcium carbonate, soil organic matter, sand size fraction particulate organic matter (SSF POM, mean weight diameter and, geometric mean diameter of aggregates, percent of macro and micro-aggregates, percent of clay, silt, sand, water dispersible clay and soil bulk density were measured. Statistical data analysis was performed by t-test at 5% level. Results Discussion: The results showed that soil splashing increased significantly in treatment 1 year after the fire in both slope 5 and 25 degree and

Distribution and function of splash, an achaete-scute homolog in the adult olfactory organ of the Caribbean spiny lobster Panulirus argus

Science.gov (United States)

Tadesse, Tizeta; Schmidt, Manfred; Walthall, William W.; Tai, Phang C.; Derby, Charles D.

2011-01-01

achaete-scute complex (ASC) genes, which encode basic helix-loop-helix transcription factors, regulate embryonic and adult neurogenesis in many animals. In adult arthropods, including crustaceans, ASC homologs have been identified but rarely functionally characterized. We took advantage of the recently identified crustacean homolog, splash (spiny lobster achaete scute homolog), in the olfactory organ of the Caribbean spiny lobster Panulirus argus to examine its role in adult neurogenesis. We tested the hypothesis that splash is associated with but not restricted to sensory neuron formation in the olfactory organ, the antennular lateral flagellum (LF), of adult spiny lobsters. We demonstrated splash labeling in epithelial cells across LF developmental zones (i.e., proliferation and mature zones), in auxiliary cells surrounding dendrites of olfactory receptor neurons (ORNs), and in immature and mature ORNs, but not in granulocytes or chromatophores. Since ORN proliferation varies with molt stage, we examined splash expression across molt stages and found that molt stage affected splash expression in the ORN mature zone but not in the proliferation zone. In vivo incorporation of bromodeoxyuridine (BrdU) showed no correlation in the cellular pattern of splash expression and BrdU labeling. The intensity of splash labeling was dramatically enhanced in the proliferation zones following LF damage, suggesting enhanced splash expression during repair and/or regeneration. We conclude that splash is not closely associated with the formation of sensory neurons under normal physiological conditions, and we propose that splash is involved in repair and regeneration. We also propose that splash has additional roles other than neurogenesis in adult crustaceans. PMID:21394934

Growth and instability of the liquid rim in the crown splash regime

Science.gov (United States)

Agbaglah, G.; Deegan, R. D.

2014-08-01

We study the formation, growth, and disintegration of jets following impact of a drop on a thin film of the same liquid for We < 1000 and Re < 2000 using a combination of numerical simulations and linear stability theory (Agbaglah et al. 2013). Our simulations faithfully capture this phenomena and are in good agreement with experimental profiles obtained from high-speed X-ray imaging.We obtain scaling relations from our simulations and use these as inputs to our stability analysis. The resulting prediction for the most unstable wavelength are in excellent agreement with experimental data. Our calculations show that the dominant destabilizing mechanism is a competition between capillarity and inertia but that deceleration of the rim provides an additional boost to growth. We also predict over the entire parameter range of our study the number and timescale for formation of secondary droplets formed during a splash, based on the assumption that the most unstable mode sets the droplet number.

The shape and dynamics of the generation of the splash forms in single-phase systems after drop hitting

Science.gov (United States)

Sochan, Agata; Beczek, Michał; Mazur, Rafał; RyŻak, Magdalena; Bieganowski, Andrzej

2018-02-01

The splash phenomenon is being increasingly explored with the use of modern measurement tools, including the high-speed cameras. Recording images at a rate of several thousand frames per second facilitates parameterization and description of the dynamics of splash phases. This paper describes the impact of a single drop of a liquid falling on the surface of the same liquid. Three single-phase liquid systems, i.e., water, petrol, and diesel fuel, were examined. The falling drops were characterized by different kinetic energy values depending on the height of the fall, which ranged from 0.1 to 7.0 m. Four forms, i.e., waves, crowns, semi-closed domes, and domes, were distinguished depending on the drop energy. The analysis of the recorded images facilitated determination of the static and dynamic parameters of each form, e.g., the maximum height of each splash form, the width of the splash form at its maximum height, and the rate of growth of the splash form. We, Re, Fr, and K numbers were determined for all analyzed liquid systems. On the basis of the obtained values of dimensionless numbers, the areas of occurrence of characteristic splash forms were separated.

COVER ILLUSTRATION: Complexities of splashing

Science.gov (United States)

Deegan, R. D.; Brunet, P.; Eggers, J.

2008-01-01

We study the impact of a drop of liquid onto a thin layer of the same liquid. We give an overview of the sequence of events that occur as the two most important dimensionless control parameters are varied. In particular, multiple cohorts of droplets can be ejected at different stages after impact due to different mechanisms. Edgerton's famous Milkdrop Coronet is only observed for a narrow range of parameters. Outside this range, the splash is either qualitatively different, or suffers from a much lower level of regularity.

Drop impact splashing and air entrapment

KAUST Repository

Thoraval, Marie-Jean

2013-03-01

Drop impact is a canonical problem in fluid mechanics, with numerous applications in industrial as well as natural phenomena. The extremely simple initial configuration of the experiment can produce a very large variety of fast and complex dynamics. Scientific progress was made in parallel with major improvements in imaging and computational technologies. Most recently, high-speed imaging video cameras have opened the exploration of new phenomena occurring at the micro-second scale, and parallel computing allowed realistic direct numerical simulations of drop impacts. We combine these tools to bring a new understanding of two fundamental aspects of drop impacts: splashing and air entrapment. The early dynamics of a drop impacting on a liquid pool at high velocity produces an ejecta sheet, emerging horizontally in the neck between the drop and the pool. We show how the interaction of this thin liquid sheet with the air, the drop or the pool, can produce micro-droplets and bubble rings. Then we detail how the breakup of the air film stretched between the drop and the pool for lower impact velocities can produce a myriad of micro-bubbles.

Is splash erosion potential species specific? Measuring of splash erosion potential under forest in different succession stages along a biodiversity gradient in the humid subtropics

Science.gov (United States)

Geißler, C.; Kühn, P.; Scholten, T.

2009-04-01

It is widely accepted that (forest) vegetation is a key control for the type and intensity of soil erosion. The current paradigm is that natural or quasi-natural vegetation protects the soil from erosion and that agricultural vegetation or land use generally enhances erosion. The latter was in focus of most research during the last decades and less interest was paid on natural systems, which are more difficult to study. Nevertheless, afforestation is widely used as a measure of soil protection against soil erosion. Rainfall can be highly erosive particularly in the humid subtropics. Regarding climate change, also precipitation regime may change in direction to even more severe storms and higher rainfall intensities; it is a research field of growing importance. Key mechanisms of a vegetation cover in reducing or enhancing erosion are modifications of drop-size distribution, retention of raindrop impact on the soil and changes in amount and spatial distribution of rainfall at the ground surface. Controlling determinants are rainfall intensity, drop size distribution, drop fall velocity, height of the canopy as well as density of the canopy, crown and leaf traits, LAI and coverage by a litter layer. Large drops are supposed to be significant sources of splash detachment in forests (Brandt 1989; Vis 1986). However, the mechanisms of reducing (or enhancing?) splash detachment under forest in relation to species richness and species composition are not well understood. Some studies indicate that raindrop impact is species specific (Calder 2001; Nanko et al. 2006) and some neglect the effects of species specific impacts (Foot & Morgan 2005). Our research uses different methods of rainfall characterization (splash cups, tipping-bucket rain gauge, laser distrometer) to reveal the described mechanisms from the canopy through different vegetation layers to the ground. First results of splash cup measurements (revised after Ellison 1947) show that sand loss under vegetation

Beam Splashes seen by the CMS detector #RestartLHC 2017 (end of April 2017)

CERN Multimedia

Mc Cauley, Thomas; Zevi Della Porta, Giovanni

2017-01-01

CMS event display from LHC beam splash on Saturday, 29th April 2017. This is the first time the full detector has seen particles produced since the beginning of the Extended Year-End Technical Stop (EYETS) 2017. In contrast to proton-proton collisions where the particles come from the center of the detector, in splash events, particles traverse the detector horizontally from one side to the other.

78 FR 28492 - Special Local Regulation; Low Country Splash, Wando River, Cooper River, and Charleston Harbor...

Science.gov (United States)

2013-05-15

...-AA08 Special Local Regulation; Low Country Splash, Wando River, Cooper River, and Charleston Harbor... establishing a special local regulation on the waters of the Wando River, Cooper River, and Charleston Harbor... rulemaking (NPRM) entitled, ``Special Local Regulation; Low Country Splash, Wando River, Cooper River, and...

78 FR 18277 - Special Local Regulation; Low Country Splash, Wando River, Cooper River, and Charleston Harbor...

Science.gov (United States)

2013-03-26

...-AA08 Special Local Regulation; Low Country Splash, Wando River, Cooper River, and Charleston Harbor... proposes to issue a special local regulation on the waters of the Wando River, Cooper River, and Charleston... Country Splash is scheduled to take place on the waters of the Wando River, Cooper River, and Charleston...

Beam Splashes seen by the CMS detector #RestartLHC 2018 (end of Mar 2018)

CERN Multimedia

Mc Cauley, Thomas; Olivito, Dominick

2018-01-01

CMS event displays from LHC beam splash on Friday, 30th March 2018. In contrast to proton-proton collisions where the particles come from the center of the detector, in splash events, particles traverse the detector horizontally from one side to the other. The time sampling for the picture, which is optimized for collisions at the center of the detector, amplifies the appearance of an asymmetric energy deposit in the end that the particles traverse last.

Origin and dynamics of vortex rings in drop splashing.

Science.gov (United States)

Lee, Ji San; Park, Su Ji; Lee, Jun Ho; Weon, Byung Mook; Fezzaa, Kamel; Je, Jung Ho

2015-09-04

A vortex is a flow phenomenon that is very commonly observed in nature. More than a century, a vortex ring that forms during drop splashing has caught the attention of many scientists due to its importance in understanding fluid mixing and mass transport processes. However, the origin of the vortices and their dynamics remain unclear, mostly due to the lack of appropriate visualization methods. Here, with ultrafast X-ray phase-contrast imaging, we show that the formation of vortex rings originates from the energy transfer by capillary waves generated at the moment of the drop impact. Interestingly, we find a row of vortex rings along the drop wall, as demonstrated by a phase diagram established here, with different power-law dependencies of the angular velocities on the Reynolds number. These results provide important insight that allows understanding and modelling any type of vortex rings in nature, beyond just vortex rings during drop splashing.

Two mechanisms of droplet splashing on a solid substrate

KAUST Repository

Jian, Zhen; Josserand, Christophe; Popinet, Sté phane; Ray, Pascal; Zaleski, Sté phane

2017-01-01

related to the gas density. The two different splashing mechanisms initially suggested theoretically are observed numerically, depending on whether a jet is created before or after the impacting droplet wets the substrate. Finally, we provide a phase

77 FR 23120 - Special Local Regulations; Lowcountry Splash Open Water Swim, Wando River and Cooper River, Mount...

Science.gov (United States)

2012-04-18

...-AA08 Special Local Regulations; Lowcountry Splash Open Water Swim, Wando River and Cooper River, Mount... establishing special local regulations on the waters of the Wando River and Cooper River in Mount Pleasant... River and Cooper River along the shoreline of Mount Pleasant, South Carolina. The Lowcountry Splash...

Mutations in MITF and PAX3 Cause “Splashed White” and Other White Spotting Phenotypes in Horses

Science.gov (United States)

Blatter, Marlis; Brooks, Samantha A.; Burger, Dominik; Drögemüller, Cord; Gerber, Vincent; Henke, Diana; Janda, Jozef; Jude, Rony; Magdesian, K. Gary; Matthews, Jacqueline M.; Poncet, Pierre-André; Svansson, Vilhjálmur; Tozaki, Teruaki; Wilkinson-White, Lorna; Penedo, M. Cecilia T.; Rieder, Stefan; Leeb, Tosso

2012-01-01

During fetal development neural-crest-derived melanoblasts migrate across the entire body surface and differentiate into melanocytes, the pigment-producing cells. Alterations in this precisely regulated process can lead to white spotting patterns. White spotting patterns in horses are a complex trait with a large phenotypic variance ranging from minimal white markings up to completely white horses. The “splashed white” pattern is primarily characterized by an extremely large blaze, often accompanied by extended white markings at the distal limbs and blue eyes. Some, but not all, splashed white horses are deaf. We analyzed a Quarter Horse family segregating for the splashed white coat color. Genome-wide linkage analysis in 31 horses gave a positive LOD score of 1.6 in a region on chromosome 6 containing the PAX3 gene. However, the linkage data were not in agreement with a monogenic inheritance of a single fully penetrant mutation. We sequenced the PAX3 gene and identified a missense mutation in some, but not all, splashed white Quarter Horses. Genome-wide association analysis indicated a potential second signal near MITF. We therefore sequenced the MITF gene and found a 10 bp insertion in the melanocyte-specific promoter. The MITF promoter variant was present in some splashed white Quarter Horses from the studied family, but also in splashed white horses from other horse breeds. Finally, we identified two additional non-synonymous mutations in the MITF gene in unrelated horses with white spotting phenotypes. Thus, several independent mutations in MITF and PAX3 together with known variants in the EDNRB and KIT genes explain a large proportion of horses with the more extreme white spotting phenotypes. PMID:22511888

Splash albedo protons between 4 and 315 MeV at high and low geomagnetic latitudes

International Nuclear Information System (INIS)

Wenzel, K.; Stone, E.C.; Vogt, R.E.

1975-01-01

The differential energy spectrum of splash albedo protons has been measured at high geomagnetic latitude near Fort Churchill, Manitoba, at three periods of the solar cycle in 1966, and 1969 and at low latitude near Palestine, Texas, in 1967 by using a balloon-borne solid state detector telescope. We observed splash albedo proton fluxes between 4 and 315 MeV of 81plus-or-minus11, 70plus-or-minus11, and 48plus-or-minus8 protons/(m 2 s sr) at high latitude in 1966, 1967, and 1969 and of 37plus-or-minus9 protons/(m 2 s sr) at low latitude in 1967. The decreases from 1966 to 1969 are due to solar modulation of the cosmic ray parent nuclei. The albedo spectrum shows a similar shape for both latitudes. The difference in intensity can be explained by different local geomagnetic cutoffs; i.e., a significant contribution to the splash albedo flux arises from primary particles with rigidity below 4.5 GV. The splash albedo flux near Fort Churchill is consistent with corresponding fluxes previously reported near 53degree--55degreeN. The flux below 100 MeV near Palestine is significantly lower than that reported by Verma (1967)

ATLAS Splash event - 6 April 2018

CERN Multimedia

ATLAS Collaboration

2018-01-01

The image shows a visualization of experimental data coming from the 'beam splash' tests run in April 2018 as part of the restart process of the LHC accelerator, after the winter break for maintenance. The image shows the hits of part of the tracking detector (in red, at the center), the energy deposits in the electromagnetic calorimeter (in green), and those in the hadronic calorimeter (in yellow). The semi-transparent azure volumes are part of the hadronic calorimeter, while the grey outer structure is part of the muon spectrometer.

Splash Dynamics of Watercolors on Dry, Wet, and Cooled Surfaces

Science.gov (United States)

Baron, David; Vaidya, Ashwin; Su, Haiyan

2015-11-01

In his classic study in 1908, A.M. Worthington gave a thorough account of splashes and their formation through visualization experiments. In more recent times, there has been renewed interest in this subject, and much of the underlying physics behind Worthington's experiments has now been clarified. One specific set of such recent studies, which motivates this paper, concerns the fluid dynamics behind Jackson Pollock's drip paintings. The physical processes and the mathematical structures hidden in his works have received serious attention and made the scientific pursuit of art a compelling area of exploration. Our work explores the interaction of watercolors with watercolor paper. Specifically, we conduct experiments to analyze the settling patterns of droplets of watercolor paint on wet and frozen paper. Variations in paint viscosity, paper roughness, paper temperature, and the height of a released droplet are examined from time of impact, through its transient stages, until its final, dry state. Observable phenomena such as paint splashing, spreading, fingering, branching, rheological deposition, and fractal patterns are studied in detail and classified in terms of the control parameters.

The Effects of Mulch Cover on Splash Erosion in Makurdi Town ...

African Journals Online (AJOL)

Soil erosion has continued to be a serious environmental problem, particularly among the farming communities. In Benue State, the dominant economic activity is subsistence farming which is done under sub humid rainfall conditions. Splash erosion resulting from intense rainfall therefore poses severe problems that can be ...

Effects of Rainfall Intensity and Slope Angle on Splash Erosion in ...

African Journals Online (AJOL)

Soil erosion is a critical global environmental problem, especially in the developing countries including Nigeria. In the humid and sub-humid tropics, splash erosion resulting from intense rainfall and slope degree pose severe land degradation problems. The objective of this study is to assess the effects of some rainfall ...

LOADING SIMULATION PROGRAM C

Science.gov (United States)

LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for simulating hydrology, sediment, and general water quality

Droplet Splashing by a Slingshot Mechanism

KAUST Repository

Thoroddsen, Sigurdur T; Thoraval, M.-J.; Takehara, K.; Etoh, T. G.

2011-01-01

When a drop impacts onto a liquid pool, it ejects a thin horizontal sheet of liquid, which emerges from the neck region connecting the two liquid masses. The leading section of this ejecta bends down to meet the pool liquid. When the sheet touches the pool, at an “elbow,” it ruptures and sends off microdroplets by a slingshot mechanism, driven by surface tension. High-speed imaging of the splashing droplets suggests the liquid sheet is of submicron thickness, as thin as 300 nm. Experiments in partial vacuum show that air resistance plays the primary role in bending the sheet. We identify a parameter regime where this slingshot occurs and also present a simple model for the sheet evolution, capable of reproducing the overall shape.

Droplet Splashing by a Slingshot Mechanism

KAUST Repository

Thoroddsen, Sigurdur T.

2011-01-18

When a drop impacts onto a liquid pool, it ejects a thin horizontal sheet of liquid, which emerges from the neck region connecting the two liquid masses. The leading section of this ejecta bends down to meet the pool liquid. When the sheet touches the pool, at an “elbow,” it ruptures and sends off microdroplets by a slingshot mechanism, driven by surface tension. High-speed imaging of the splashing droplets suggests the liquid sheet is of submicron thickness, as thin as 300 nm. Experiments in partial vacuum show that air resistance plays the primary role in bending the sheet. We identify a parameter regime where this slingshot occurs and also present a simple model for the sheet evolution, capable of reproducing the overall shape.

Visualization and mechanisms of splashing erosion of electrodes in a DC air arc

International Nuclear Information System (INIS)

Wu, Yi; Cui, Yufei; Rong, Mingzhe; Yang, Fei; Sun, Hao; Niu, Chunping; Fan, Shaodi; Murphy, Anthony B

2017-01-01

The splashing erosion of electrodes in a DC atmospheric-pressure air arc has been investigated by visualization of the electrode surface and the sputtered droplets, and tracking of the droplet trajectories, using image processing techniques. A particle tracking velocimetry algorithm has been introduced to measure the sputtering velocity distribution. Erosion of both tungsten–copper and tungsten–ceria electrodes is studied; in both cases electrode erosion is found to be dominated by droplet splashing rather than metal evaporation. Erosion is directly influenced by both melting and the formation of plasma jets, and can be reduced by the tuning of the plasma jet and electrode material. The results provide an understanding of the mechanisms that lead to the long lifetime of tungsten–copper electrodes, and may provide a path for the design of the electrode system subjected to electric arc to minimize erosion. (letter)

Visualization and mechanisms of splashing erosion of electrodes in a DC air arc

Science.gov (United States)

Wu, Yi; Cui, Yufei; Rong, Mingzhe; Murphy, Anthony B.; Yang, Fei; Sun, Hao; Niu, Chunping; Fan, Shaodi

2017-11-01

The splashing erosion of electrodes in a DC atmospheric-pressure air arc has been investigated by visualization of the electrode surface and the sputtered droplets, and tracking of the droplet trajectories, using image processing techniques. A particle tracking velocimetry algorithm has been introduced to measure the sputtering velocity distribution. Erosion of both tungsten-copper and tungsten-ceria electrodes is studied; in both cases electrode erosion is found to be dominated by droplet splashing rather than metal evaporation. Erosion is directly influenced by both melting and the formation of plasma jets, and can be reduced by the tuning of the plasma jet and electrode material. The results provide an understanding of the mechanisms that lead to the long lifetime of tungsten-copper electrodes, and may provide a path for the design of the electrode system subjected to electric arc to minimize erosion.

Micro-splashing by drop impacts

KAUST Repository

Thoroddsen, Sigurdur T; Takehara, Kohsei; Etoh, Takeharugoji

2012-01-01

We use ultra-high-speed video imaging to observe directly the earliest onset of prompt splashing when a drop impacts onto a smooth solid surface. We capture the start of the ejecta sheet travelling along the solid substrate and show how it breaks up immediately upon emergence from the underneath the drop. The resulting micro-droplets are much smaller and faster than previously reported and may have gone unobserved owing to their very small size and rapid ejection velocities, which approach 100 m s-1, for typical impact conditions of large rain drops. We propose a phenomenological mechanism which predicts the velocity and size distribution of the resulting microdroplets. We also observe azimuthal undulations which may help promote the earliest breakup of the ejecta. This instability occurs in the cusp in the free surface where the drop surface meets the radially ejected liquid sheet. © 2012 Cambridge University Press.

Micro-splashing by drop impacts

KAUST Repository

Thoroddsen, Sigurdur T.

2012-07-18

We use ultra-high-speed video imaging to observe directly the earliest onset of prompt splashing when a drop impacts onto a smooth solid surface. We capture the start of the ejecta sheet travelling along the solid substrate and show how it breaks up immediately upon emergence from the underneath the drop. The resulting micro-droplets are much smaller and faster than previously reported and may have gone unobserved owing to their very small size and rapid ejection velocities, which approach 100 m s-1, for typical impact conditions of large rain drops. We propose a phenomenological mechanism which predicts the velocity and size distribution of the resulting microdroplets. We also observe azimuthal undulations which may help promote the earliest breakup of the ejecta. This instability occurs in the cusp in the free surface where the drop surface meets the radially ejected liquid sheet. © 2012 Cambridge University Press.

Experimental investigations on the contribution of the splash-zones in counter-flow cooling towers for water cooling

International Nuclear Information System (INIS)

Vladea, I.; Barbu, V.

1976-01-01

The relatively high cost of cooling tower packs has led to investigate the contribution of the splash-zones in counter-flow cooling towers, and thereby to determine whether the pack could not be reduced so far, as to be - under certain circumstance - completely eliminated. In this case, one would come to a pure splash cooling tower which would contain inside the equipment required for drop formation only. This problem was investigated experimentally, and it was found that the pack of such a cooling tower could not be eliminated without a reduction in tower effectiveness. (orig.) [de

LOADING SIMULATION PROGRAM C

Data.gov (United States)

U.S. Environmental Protection Agency — LSPC is the Loading Simulation Program in C++, a watershed modeling system that includes streamlined Hydrologic Simulation Program Fortran (HSPF) algorithms for...

The Effect of Salt Splash on Nylon 6,6

OpenAIRE

Steward, Scott D

1999-01-01

Abstract: One of the most common environmental exposures that nylon undergoes, when used for automotive applications, is that of salt splash, which commonly occurs during winter driving. This study looks at the effect of various salts (NaCl, KCl, CaCl2) on the thermal and mechanical properties of nylon when exposed to one and four molar aqueous salt solutions. It was found that the diffusion of salt solutions into nylon 6,6 occurred in a pseudo-Fickian manner. Also, it was found that the p...

Impact induced splash and spill in a quasi-confided granular medium

Science.gov (United States)

Ogale, S. B.

2005-03-01

Dissipation of the energy of impact in a granular medium and its effects has been a subject of considerable scientific for quite some time. In this work we have explored and analyzed the splash and spill effects caused by the impact of a ball dropped from a height into a granular medium in a open container. Three different granular media, namely rice, mustard seeds, and cream of wheat were used. The amount of spilled-over granular matter was measured as a function of the ball-drop height. Digital pictures of the splash process were also recorded. The quantity of spilled granular matter varies linearly with the impact energy. However additional step like structures are also noted. Specifically, a distinct and large jump is seen in the spilled quantity at a specific impact energy in the case of mustard seeds, which also exhibit obvious charging effects and repulsion. Although the parameters such as mass per grain and packing density for the case of mustard seeds are intermediate between those for rice and cream of wheat, the spill quantity for comparable impact energy is considerably higher. These data will be presented and discussed.

Model of liquid-metal splashing in the cathode spot of a vacuum arc discharge

International Nuclear Information System (INIS)

Gashkov, M. A.; Zubarev, N. M.; Zubareva, O. V.; Mesyats, G. A.; Uimanov, I. V.

2016-01-01

The formation of microjets is studied during the extrusion of a melted metal by the plasma pressure from craters formed on a cathode in a burning vacuum arc. An analytic model of liquid-metal splashing that includes two stages is proposed. At the first stage, the liquid motion has the axial symmetry and a liquid-metal wall surrounding the crater is formed. At the second stage, the axial symmetry is broken due to the development of the Plateau–Rayleigh instability in the upper part of the wall. The wall breakup process is shown to have a threshold. The minimal plasma pressure and the minimal electric current flowing through the crater required for obtaining the liquid-metal splashing regime are found. The basic spatial and temporal characteristics of the jet formation process are found using the analytic model.

SWFSC/MMTD/AK: Structure of Populations, Level of Abundance, and Status of Humpbacks (SPLASH) 2004

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This project was part of a larger international project (SPLASH) designed to estimate the abundance and determine the population structure for humpback whales...

Thermal shock and splash effects on burned gypseous soils from the Ebro Basin (NE Spain)

Science.gov (United States)

León, J.; Seeger, M.; Badía, D.; Peters, P.; Echeverría, M. T.

2014-03-01

Fire is a natural factor of landscape evolution in Mediterranean ecosystems. The middle Ebro Valley has extreme aridity, which results in a low plant cover and high soil erodibility, especially on gypseous substrates. The aim of this research is to analyze the effects of moderate heating on physical and chemical soil properties, mineralogical composition and susceptibility to splash erosion. Topsoil samples (15 cm depth) were taken in the Remolinos mountain slopes (Ebro Valley, NE Spain) from two soil types: Leptic Gypsisol (LP) in a convex slope and Haplic Gypsisol (GY) in a concave slope. To assess the heating effects on the mineralogy we burned the soils at 105 and 205 °C in an oven and to assess the splash effects we used a rainfall simulator under laboratory conditions using undisturbed topsoil subsamples (0-5 cm depth of Ah horizon). LP soil has lower soil organic matter (SOM) and soil aggregate stability (SAS) and higher gypsum content than GY soil. Gypsum and dolomite are the main minerals (>80%) in the LP soil, while gypsum, dolomite, calcite and quartz have similar proportions in GY soil. Clay minerals (kaolinite and illite) are scarce in both soils. Heating at 105 °C has no effect on soil mineralogy. However, heating to 205 °C transforms gypsum to bassanite, increases significantly the soil salinity (EC) in both soil units (LP and GY) and decreases pH only in GY soil. Despite differences in the content of organic matter and structural stability, both soils show no significant differences (P pores is reduced by heating, as derived from variations in soil water retention capacity.

Influence of Rust Permeability on Corrosion of E690 Steel in Industrial and Non-industrial Marine Splash Zones

Science.gov (United States)

Chen, Mindong; Pang, Kun; Liu, Zhiyong; Wu, Junsheng; Li, Xiaogang

2018-05-01

The corrosion behaviour of E690 steel in industrial and non-industrial marine splash environments was studied by environmental testing, morphology analysis, electrochemical measurements, and scanning Kelvin probe microscopy. Chloride and sulphide anions were found to diffuse across the rust layer following the evaporation of seawater splashed on the steel's surface. The cation-selective permeability of the rust layer resulted in an anion concentration gradient across the rust layer, which was more significant in the presence of sulphur dioxide. In addition, sulphur dioxide enhanced the formation of α-FeOOH, which led to the formation of distinct anode and cathode areas at the rust/steel interface.

LHC Beam Splash seen by the ATLAS detector - 5 Apr 2015 - run 260272 - event 6539

CERN Multimedia

ATLAS Collaboration

2015-01-01

Event display of one of the collimator "splash" events seen by the ATLAS experiment in LHC Run-2, on Tuesday April the 5th : run 260272, event 6539 . The collimator position is 140m in front of the ATLAS interaction point.

First beam splashes at the LHC

CERN Multimedia

CERN Bulletin

2015-01-01

After a two-year shutdown, the first beams of Run 2 circulated in the LHC last Sunday. On Tuesday, the LHC operators performed dedicated runs to allow some of the experiments to record their first signals coming from particles splashed out when the circulating beams hit the collimators. Powerful reconstruction software then transforms the electronic signals into colourful images.     “Splash” events are used by the experiments to test their numerous subdetectors and to synchronise them with the LHC clock. These events are recorded when the path of particles travelling in the LHC vacuum pipe is intentionally obstructed using collimators – one-metre-long graphite or tungsten jaws that are also used to catch particles that wander too far from the beam centre and to protect the accelerator against unavoidable regular and irregular beam losses. The particles sprayed out of the collision between the beam and the collimators are mostly muons. ATLAS and CMS&...

Investigation and prevention of droplet splashing during operation of a sodium free jet flow

International Nuclear Information System (INIS)

Stoppel, L.; Gordeev, S.; Wetzel, T.; Fellmoser, F.; Daubner, M.

2010-01-01

Many accelerator application concepts consider liquid metal as a windowless target, at which the particle beam does directly hit the liquid. One of such concepts is studied in the European project ''DIRAC-Secondary beams - Design Study''. This project is focused on the preliminary research work for construction of a new international particle accelerator - Facility for Antiproton and Ion Research (FAIR) in Darmstadt. The planned accelerator is aimed to work with high-energy heavy-ions, such as U 238 . One of the key elements of the FAIR facility is a liquid-metal-target, made in the form of a rectangular shaped Lithium jet aligned with the gravity vector. In the course of preliminary investigations the theoretical and practical conditions for a stable liquid-metal-jet conforming to the FAIR-requirements have been studied in the Karlsruhe Liquid Metal Laboratory (KALLA) sodium facility. The acquired scientific and technological results can be transferred to liquid-metal targets in nuclear applications, for example, the IFMIF-Target for the study of fusion reactor materials and the Myrrah/XT-ADS target. The main goals of the KALLA-part of the project were to design and build a facility for experimental research on hydrodynamic phenomena of the free surface liquid metal flow as well as to look at technological problems influencing the hydrodynamic stability of such flows. One of such problems emerged already during the startup of the facility: Splashing of liquid metal drops in the vacuum volume of the target box. As a result of such splashing process, liquid metal droplets are accumulated on various internal constructional elements of the target box, for example, on the inspection windows. This effect prohibits long term operation with the facility. The present paper describes the methods used to reduce the splashing to a minimum. (orig.)

Impact-induced splash and spill in a quasi-confined granular medium

Science.gov (United States)

Ogale, S. B.; Shinde, S. R.; Karve, P. A.; Ogale, Abhijit S.; Kulkarni, A.; Athawale, A.; Phadke, A.; Thakurdas, R.

2006-05-01

The splash and spill effects caused by the impact of a ball dropped from a height into a granular medium held in a small open container are examined. Different granular media, namely rice, mustard seeds, cream of wheat and plastic beads are used. The quantity of spilled-over granular matter ( W, grams) is measured as a function of the ball-drop height and compared for different cases. Digital pictures of the splash process are also recorded. The quantity W is seen to vary approximately linearly with the energy of impact. Interestingly, a distinct upward jump is seen in the spilled quantity at specific impact energy in the case of mustard seeds, which have spherical shape and also exhibit some charging effects. Similar jump was also confirmed for the case of plastic beads with broadly similar properties. Although the parameters such as mass per grain and packing density for the case of mustard seeds are intermediate between those for rice and cream of wheat, the spill quantity for comparable impact energy is considerably higher in the former case. The possible reasons for this non-monotonicity of behavior are discussed in terms of the differences in grain shapes and properties. Experiments are also performed using plastic beads of the same type but with four different sizes to explore the dependence of spilled quantity on bead size. The container size dependence is also examined for various bead types. Interesting systematics are seen, which are discussed qualitatively.

Ash wettability conditions splash erosion in the postfire

Science.gov (United States)

Gordillo-Rivero, Ángel J.; de Celis, Reyes; García-Moreno, Jorge; Jiménez-Compán, Elizabeth; Alanís, Nancy; Cerdà, Artemi; Pereira, Paulo; Zavala, Lorena M.; Jordán, Antonio

2015-04-01

at each point of study were collected monthly and determined gravimetrically after oven drying between November 2012 and May 2013. 3. RESULTS AND DISCUSSION Depending on the intensity of the water repellency, the ash layer fluctuated between wettable and very strongly water repellent. The ash has a high permeability and water storage. However, its hydrophilic character has been emphasized rarely (Cerdà and Doerr, 2008). Different authors have described hydrophobic behaviors depending on the burned vegetation such as oak (Gabet and Sternberg, 2008) or pine forest (Stark, 1977) in the United States, eucalyptus forest in Australia (Khanna et al., 1996 ) or Mediterranean tree and shrub species in Spain (Bodí et al., 2011). In the latter case, Bodí et al. (2011) observed that ash has different properties depending on the combustion conditions, organic carbon content and color. This variability of behavior agrees with the results obtained in the present work. Significant differences between splash erosion from wettable and water-repellent ash zones were found (p authors have suggested that ash acts protecting soil from the direct impact of raindrops and thus reduce sediment dispersion by splash (Cerdà and Doerr, 2008, Larsen et al, 2009; Woods and Balfour, 2008, Zavala et al, 2009). However, there is very little information about the effect of hydrophobicity on splash erosion. In a rainfall simulation experiment under laboratory conditions, Bodí et al. (2012) observed that splash erosion was at least two times higher in samples of water repellent soil than in hydrophilic soil, but no differences in ash loss or thickness of ash layer were observed. 4. CONCLUSIONS Our results highlight the role played by ash water repellency and the influence of burn severity on the development of a pattern of splash erosion intensities. Splash erosion was reduced in one order of magnitude on wettable ash zones. In contrast, the presence of a water-repellent ash layer increases the

Program For Parallel Discrete-Event Simulation

Science.gov (United States)

Beckman, Brian C.; Blume, Leo R.; Geiselman, John S.; Presley, Matthew T.; Wedel, John J., Jr.; Bellenot, Steven F.; Diloreto, Michael; Hontalas, Philip J.; Reiher, Peter L.; Weiland, Frederick P.

1991-01-01

User does not have to add any special logic to aid in synchronization. Time Warp Operating System (TWOS) computer program is special-purpose operating system designed to support parallel discrete-event simulation. Complete implementation of Time Warp mechanism. Supports only simulations and other computations designed for virtual time. Time Warp Simulator (TWSIM) subdirectory contains sequential simulation engine interface-compatible with TWOS. TWOS and TWSIM written in, and support simulations in, C programming language.

2D SPLASH: a new method to determine the fatty infiltration of the rotator cuff muscles

International Nuclear Information System (INIS)

Kenn, Werner; Huemmer, Christian; Koestler, Herbert; Hahn, Dietbert; Boehm, Dirk; Gohlke, Frank

2004-01-01

The objective of this paper is to quantify the fatty degeneration (infiltration) of rotator cuff muscles with a new spectroscopic FLASH (SPLASH) sequence. Before planned surgery (reconstruction or muscle transfer), 20 patients (13 men, 7 women; 35-75 years) with different stages of rotator cuff disease underwent an MR examination in a 1.5-T unit. The protocol consists of imaging sequences and a newly implemented SPLASH, which allows an exact quantification of the fat/water ratio with a high spatial resolution in an arbitrarily shaped region of interest (ROI). The percentages of fat in the rotator cuff muscles were determined. To determine statistically significant differences between the different stages of rotator cuff tear, a Kruskal-Wallis H test was used. Fatty infiltration of the supraspinatus muscle was correlated with cross-sectional area (CSA) measures (Bravais-Pearson). We found significant differences between different stages of rotator cuff disease, the fatty infiltration and the volume loss (determined by the occupation ratio) of the supraspinatus muscle. With the increasing extent of rotator cuff disease, fatty infiltration increases significantly, as does the volume loss of the supraspinatus muscle. Comparing fatty infiltration and the occupation ratio individually, there was only a moderate inverse correlation between fatty infiltration and the occupation ratio, with considerable variation of data. Fatty infiltration of the infraspinatus muscle occurred when the infraspinatus tendon was involved to a lesser extent. The SPLASH sequence allows exact quantification of fatty infiltration in an arbitrarily shaped ROI. The extent of atrophy and fatty infiltration correlates with the size of the tear. Atrophy and fatty infiltration correlate only moderately and should be evaluated separately. (orig.)

Effects of simulated rain acidified with sulfuric acid on host-parasite interactions

Science.gov (United States)

D. S. Shriner

1976-01-01

Wind-blown rain, rain splash, and films of free moisture play important roles in the epidemiology of many plant diseases. The effects of simulated rain acidified with sulfuric acid were studied on several host-parasite systems. Plants were exposed, in greenhouse or field, to simulated rain of pH 3.2 ? 0.1 or pH 6.0 ? 0.2. Simulated "rain" of pH 3.2 resulted...

Programming for a nuclear reactor instrument simulator

International Nuclear Information System (INIS)

Cohn, C.E.

1989-01-01

A new computerized control system for a transient test reactor incorporates a simulator for pre-operational testing of control programs. The part of the simulator pertinent to the discussion here consists of two microprocessors. An 8086/8087 reactor simulator calculates simulated reactor power by solving the reactor kinetics equations. An 8086 instrument simulator takes the most recent power value developed by the reactor simulator and simulates the appropriate reading on each of the eleven reactor instruments. Since the system is required to run on a one millisecond cycle, careful programming was required to take care of all eleven instruments in that short time. This note describes the special programming techniques used to attain the needed performance

A NOESY-HSQC simulation program, SPIRIT

International Nuclear Information System (INIS)

Zhu Leiming; Dyson, H. Jane; Wright, Peter E.

1998-01-01

A program SPIRIT (Simulation Program considering Incomplete Recovery of z magnetization and INEPT Transfer efficiency) has been developed to simulate three-dimensional NOESY-HSQC spectra. This program takes into account (1) different transfer efficiency during INEPT and reverse INEPT durations due to differential relaxation rates and 1 J coupling constants; (2) the different effect of the sensitivity-enhancement scheme on CH, CH 2 and CH 3 systems; and (3) incomplete recovery of longitudinal magnetization between scans. The simulation program incorporates anisotropic tumbling mode for symmetric tops, and allows for differential external relaxation rates for protons. Some well-defined internal motions, such as the fast rotation of methyl groups, are taken into account. The simulation program also allows for input of multiple conformations and their relative populations to calculate the average relaxation matrix to account for slow internal motions. With the SPIRIT program, the sensitivity-enhanced NOESY-HSQC experiment can be used directly in the evaluation of the accuracy of structures, which can potentially be improved by direct refinement against the primary data. Abbreviations: NOESY, nuclear Overhauser enhancement spectroscopy; HSQC, heteronuclear single quantum correlation; INEPT, insensitive nuclei enhanced by polarization transfer

Introduction of a theoretical splashing degree to assess the performance of low-viscosity oils in filling of capsules.

Science.gov (United States)

Niederquell, Andreas; Kuentz, Martin

2011-03-01

These days an alternative to soft capsules is liquid-filled hard capsules. Their filling technology was investigated earlier with highly viscous formulations, while hardly any academic research focused on low-viscosity systems. Accordingly, this work addressed the filling of such oils that are splashing during the dosing process. It was aimed to first study capsule filling, using middle-chain triglycerides as reference oil, in order to then evaluate the concept of a new theoretical splashing degree for different oils. A laboratory-scale filling machine was used that included capsule sealing. Thus, the liquid encapsulation by microspray technology was employed to seal the dosage form. As a result of the study with reference oil, the filling volume and the temperature were found to be significant for the rate of leaking capsules. The filling volume was also important for weight variability of the capsules. However, most critical for this variability was the diameter of the filling nozzle. We proposed a power law for the coefficient of weight variability as a function of the nozzle diameter and the obtained exponent agreed with the proposed theory. Subsequently, a comparison of different oils revealed that the relative splashing degree shared a correlation with the coefficient of the capsule weight variability (Pearson product moment correlation of r=0.990). The novel theoretical concept was therefore found to be predictive for weight variability of the filled capsules. Finally, guidance was provided for the process development of liquid-filled capsules using low-viscosity oils. © 2011 American Association of Pharmaceutical Scientists

A benchmark study for the crown-type splashing dynamics of one- and two-component droplet wall-film interactions

Science.gov (United States)

Geppert, A.; Terzis, A.; Lamanna, G.; Marengo, M.; Weigand, B.

2017-12-01

The present paper investigates experimentally the impact dynamics of crown-type splashing for miscible two- and one-component droplet wall-film interactions over a range of Weber numbers and dimensionless film thicknesses. The splashing outcome is parametrised in terms of a set of quantifiable parameters, such as crown height, top and base diameter, wall inclination, number of fingers, and secondary droplet properties. The results show that the outcome of a splashing event is not affected by the choice of similar or dissimilar fluids, provided the dimensionless film thickness is larger than 0.1. Below this threshold, distinctive features of two-component interactions appear, such as hole formation and crown bottom breakdown. The observation of different crown shapes (e.g. V-shaped, cylindrical, and truncated-cone) confirms that vorticity production induces changes in the crown wall inclination, thus affecting the evolution of the crown height and top diameter. The evolution of the crown base diameter, instead, is mainly dependent on the relative importance of liquid inertia and viscous losses in the wall-film. The maximum number of liquid fingers decreases with increasing wall, film thickness, due to the enhanced attenuation of the effect of surface properties on the fingering process. The formation of secondary droplets is also affected by changes in the crown wall inclination. In particular, for truncated-cone shapes the occurrence of crown rim contraction induces a large scatter in the secondary droplet properties. Consequently, empirical models for the maximum number and mean diameter of the secondary droplets are derived for V-shaped crowns, as observed for the hexadecane-Hyspin interactions.

Current status of endoscopic simulation in gastroenterology fellowship training programs.

Science.gov (United States)

Jirapinyo, Pichamol; Thompson, Christopher C

2015-07-01

Recent guidelines have encouraged gastroenterology and surgical training programs to integrate simulation into their core endoscopic curricula. However, the role that simulation currently has within training programs is unknown. This study aims to assess the current status of simulation among gastroenterology fellowship programs. This questionnaire study consisted of 38 fields divided into two sections. The first section queried program directors' experience on simulation and assessed the current status of simulation at their institution. The second portion surveyed their opinion on the potential role of simulation on the training curriculum. The study was conducted at the 2013 American Gastroenterological Association Training Directors' Workshop in Phoenix, Arizona. The participants were program directors from Accreditation Council for Graduate Medical Education accredited gastroenterology training programs, who attended the workshop. The questionnaire was returned by 69 of 97 program directors (response rate of 71%). 42% of programs had an endoscopic simulator. Computerized simulators (61.5%) were the most common, followed by mechanical (30.8%) and animal tissue (7.7%) simulators, respectively. Eleven programs (15%) required fellows to use simulation prior to clinical cases. Only one program has a minimum number of hours fellows have to participate in simulation training. Current simulators are deemed as easy to use (76%) and good educational tools (65%). Problems are cost (72%) and accessibility (69%). The majority of program directors believe that there is a need for endoscopic simulator training, with only 8% disagreeing. Additionally, a majority believe there is a role for simulation prior to initiation of clinical cases with 15% disagreeing. Gastroenterology fellowship program directors widely recognize the importance of simulation. Nevertheless, simulation is used by only 42% of programs and only 15% of programs require that trainees use simulation prior to

Large and Small Droplet Impingement Data on Airfoils and Two Simulated Ice Shapes

Science.gov (United States)

Papadakis, Michael; Wong, See-Cheuk; Rachman, Arief; Hung, Kuohsing E.; Vu, Giao T.; Bidwell, Colin S.

2007-01-01

Water droplet impingement data were obtained at the NASA Glenn Icing Research Tunnel (IRT) for four wings and one wing with two simulated ice shapes. The wings tested include three 36-in. chord wings (MS(1)-317, GLC-305, and a NACA 652-415) and a 57-in. chord Twin Otter horizontal tail section. The simulated ice shapes were 22.5- and 45-min glaze ice shapes for the Twin Otter horizontal tail section generated using the LEWICE 2.2 ice accretion program. The impingement experiments were performed with spray clouds having median volumetric diameters of 11, 21, 79, 137, and 168 mm. Comparisons to the experimental data were generated which showed good agreement for the clean wings and ice shapes at lower drop sizes. For larger drop sizes LEWICE 2.2 over predicted the collection efficiencies due to droplet splashing effects which were not modeled in the program. Also for the more complex glaze ice shapes interpolation errors resulted in the over prediction of collection efficiencies in cove and shadow regions of ice shapes.

High Speed Simulation Framework for Reliable Logic Programs

International Nuclear Information System (INIS)

Lee, Wan-Bok; Kim, Seog-Ju

2006-01-01

This paper shows a case study of designing a PLC logic simulator that was developed to simulate and verify PLC control programs for nuclear plant systems. The nuclear control system requires strict restrictions rather than normal process control system does, since it works with nuclear power plants requiring high reliability under severe environment. One restriction is the safeness of the control programs which can be assured by exploiting severe testing. Another restriction is the simulation speed of the control programs, that should be fast enough to control multi devices concurrently in real-time. To cope with these restrictions, we devised a logic compiler which generates C-code programs from given PLC logic programs. Once the logic program was translated into C-code, the program could be analyzed by conventional software analysis tools and could be used to construct a fast logic simulator after cross-compiling, in fact, that is a kind of compiled-code simulation

Clinical training: a simulation program for phlebotomy

Directory of Open Access Journals (Sweden)

Araki Toshitaka

2008-01-01

Full Text Available Abstract Background Basic clinical skills training in the Japanese medical education system has traditionally incorporated on-the-job training with patients. Recently, the complementary use of simulation techniques as part of this training has gained popularity. It is not known, however, whether the participants view this new type of education program favorably; nor is the impact of this program known. In this study we developed a new simulation-based training program in phlebotomy for new medical residents and assessed their satisfaction with the program Methods The education program comprised two main components: simulator exercise sessions and the actual drawing of blood from other trainees. At the end of the session, we surveyed participant sentiment regarding the program. Results There were 43 participants in total. In general, they were highly satisfied with the education program, with all survey questions receiving scores of 3 or more on a scale of 1–5 (mean range: 4.3 – 4.8, with 5 indicating the highest level of satisfaction. Additionally, their participation as a 'patient' for their co-trainees was undertaken willingly and was deemed to be a valuable experience. Conclusion We developed and tested an education program using a simulator for blood collection. We demonstrated a high satisfaction level among the participants for this unique educational program and expect that it will improve medical training, patient safety, and quality of care. The development and dissemination of similar educational programs involving simulation for other basic clinical skills will be undertaken in the future.

LHC Beam Splash seen by the ATLAS detector, 7 Apr 2015 - Run 260466 - event 22425

CERN Multimedia

Adam Bourdarios, Claire

2015-01-01

Event display of one of the collimator "splash" event seen by the ATLAS experiment in LHC Run-2 , on Tuesday April the 7th : event 22425, run 260466. The collimator position is 140m in front of the ATLAS interaction point. The spray of particles enters ATLAS from the left hand side of the picture. The length of the yellow bars indicates the energy deposited in the ATLAS calorimeter.

G4Beamline Program for Radiation Simulations

International Nuclear Information System (INIS)

Beard, Kevin; Roberts, Thomas J.; Degtiarenko, Pavel

2008-01-01

G4beamline, a program that is an interface to the Geant4 toolkit that we have developed to simulate accelerator beamlines, is being extended with a graphical user interface to quickly and efficiently model experimental equipment and its shielding in experimental halls. The program is flexible, user friendly, and requires no programming by users, so that even complex systems can be simulated quickly. This improved user interface is of much wider application than just the shielding simulations that are the focus of this project. As an initial application, G4beamline is being extended to provide the simulations that are needed to determine the radiation sources for the proposed experiments at Jefferson Laboratory so that shielding issues can be evaluated. Since the program already has the capabilities needed to simulate the transport of all known particles, including scattering, attenuation, interactions, and decays, the extension involves implementing a user-friendly graphical user inter

Programming for a nuclear reactor instrument simulation

International Nuclear Information System (INIS)

Cohn, C.

1988-01-01

This note discusses 8086/8087 machine-language programming for simulation of nuclear reactor instrument current inputs by means of a digital-analog converter (DAC) feeding a bank of series input resistors. It also shows FORTRAN programming for generating the parameter tales used in the simulation. These techniques would be generally useful for high-speed simulation of quantities varying over many orders of magnitude

A links manipulator simulation program interim report

International Nuclear Information System (INIS)

Noble, R.A.

1987-04-01

A computer program to simulate the performance of the Heysham II rail-following manipulator has been developed. The program is being used to develop and test the rail-following control algorithms which will be used to control movements of the manipulator when it is operating below the gas baffle dome. The simulation includes the dynamic responses of the manipulator joint drives, excluding friction, backlash and compliance. It also includes full details of the manipulator's geometry. A method is given whereby the actual manipulator dynamics can be written into the program once these have been established by measurement. The program is written in FORTRAN and runs on a Perkin-Elmer 3220 mini-computer. The simulation program responds to velocity demands on the individual joints. These will normally come from the control program, in which they will be manually controlled by a joystick. A sigma 5664 colour graphics generator is programmed to display the current position of the manipulator. (UK)

HASP: human acts simulation program

International Nuclear Information System (INIS)

Asai, Kiyoshi; Kambayashi, Shaw; Higuchi, Kenji; Kume, Etsuo; Otani, Takayuki; Fujii, Minoru; Uenaka, Junji; Fujisaki, Masahide.

1990-01-01

The Human Acts Simulation Program (HASP) aims computer simulations of mechanized human acts in a nuclear plant by a human shaped intelligent robot. The HASP has started as a ten-year program at Japan Atomic Energy Research Institute since 1987. The purposes of HASP are threefold as follows; development of basic and generalized design technologies for intelligent robots, development of basic technologies for an advanced intelligent and automatic nuclear power plant, and provision of artificial intelligence techniques for researchers in the nuclear field. In this paper, the contents of the HASP are described. (author)

Fusion Simulation Program

International Nuclear Information System (INIS)

Greenwald, Martin

2011-01-01

Many others in the fusion energy and advanced scientific computing communities participated in the development of this plan. The core planning team is grateful for their important contributions. This summary is meant as a quick overview the Fusion Simulation Program's (FSP's) purpose and intentions. There are several additional documents referenced within this one and all are supplemental or flow down from this Program Plan. The overall science goal of the DOE Office of Fusion Energy Sciences (FES) Fusion Simulation Program (FSP) is to develop predictive simulation capability for magnetically confined fusion plasmas at an unprecedented level of integration and fidelity. This will directly support and enable effective U.S. participation in International Thermonuclear Experimental Reactor (ITER) research and the overall mission of delivering practical fusion energy. The FSP will address a rich set of scientific issues together with experimental programs, producing validated integrated physics results. This is very well aligned with the mission of the ITER Organization to coordinate with its members the integrated modeling and control of fusion plasmas, including benchmarking and validation activities. (1). Initial FSP research will focus on two critical Integrated Science Application (ISA) areas: ISA1, the plasma edge; and ISA2, whole device modeling (WDM) including disruption avoidance. The first of these problems involves the narrow plasma boundary layer and its complex interactions with the plasma core and the surrounding material wall. The second requires development of a computationally tractable, but comprehensive model that describes all equilibrium and dynamic processes at a sufficient level of detail to provide useful prediction of the temporal evolution of fusion plasma experiments. The initial driver for the whole device model will be prediction and avoidance of discharge-terminating disruptions, especially at high performance, which are a critical

Plasma Simulation Program

Energy Technology Data Exchange (ETDEWEB)

Greenwald, Martin

2011-10-04

Many others in the fusion energy and advanced scientific computing communities participated in the development of this plan. The core planning team is grateful for their important contributions. This summary is meant as a quick overview the Fusion Simulation Program's (FSP's) purpose and intentions. There are several additional documents referenced within this one and all are supplemental or flow down from this Program Plan. The overall science goal of the DOE Office of Fusion Energy Sciences (FES) Fusion Simulation Program (FSP) is to develop predictive simulation capability for magnetically confined fusion plasmas at an unprecedented level of integration and fidelity. This will directly support and enable effective U.S. participation in International Thermonuclear Experimental Reactor (ITER) research and the overall mission of delivering practical fusion energy. The FSP will address a rich set of scientific issues together with experimental programs, producing validated integrated physics results. This is very well aligned with the mission of the ITER Organization to coordinate with its members the integrated modeling and control of fusion plasmas, including benchmarking and validation activities. [1]. Initial FSP research will focus on two critical Integrated Science Application (ISA) areas: ISA1, the plasma edge; and ISA2, whole device modeling (WDM) including disruption avoidance. The first of these problems involves the narrow plasma boundary layer and its complex interactions with the plasma core and the surrounding material wall. The second requires development of a computationally tractable, but comprehensive model that describes all equilibrium and dynamic processes at a sufficient level of detail to provide useful prediction of the temporal evolution of fusion plasma experiments. The initial driver for the whole device model will be prediction and avoidance of discharge-terminating disruptions, especially at high performance, which are a

Use of Simulation in Canadian Neonatal-Perinatal Medicine Training Programs.

Science.gov (United States)

Wong, Jonathan; Finan, Emer; Campbell, Douglas

2017-07-08

Introduction Simulation is used for the delivery of education and on occasion assessment. Before such a tool is used routinely in neonatal training programs across Canada, a need assessment is required to determine its current usage by accredited training programs. Our aim was to characterize the type of simulation modalities used and the perceived simulation-based training needs in Canadian neonatal-perinatal medicine (NPM) training programs. Methods A 22-item and 13-item online descriptive survey was sent to all NPM program directors and fellows in Canada, respectively. The survey was modeled on a previously validated tool by Johnston, et al. and responses were collected over 30 days. Results In total, eight (63%) program directors and 24 (28%) fellows completed the survey, with all respondents indicating that simulation is being used. Both lab-based and in situ simulations are occurring, with a range of simulation modalities employed to primarily teach resuscitation, procedural and communication skills. Fellows indicated that simulation should also be used to also teach other important topics, including disease-specific management, crisis resource management, and prevention of medical error. Five (63%) programs have faculty with formal simulation training and four (50%) programs have at least one faculty involved in simulation research. Conclusion Simulation is widely used in Canadian NPM training programs, with program directors and fellows identifying this as an important tool. Simulation can be used to teach a range of skills, but programs need to align their curriculum with both training objectives and learner needs. There is an opportunity for faculty development and increased simulation research.

Module-based Simulation System for efficient development of nuclear simulation programs

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Wakabayashi, Jiro

1990-01-01

Module-based Simulation System (MSS) has been developed to realize a new software environment enabling versatile dynamic simulation of a complex nuclear power plant system flexibly. Described in the paper are (i) fundamental methods utilized in MMS and its software systemization, (ii) development of human interface system to help users in generating integrated simulation programs automatically, and (iii) development of an intelligent user support system for helping users in the two phases of automatical semantic diagnosis and consultation to automatic input data setup for the MSS-generated programs. (author)

Performance study of protective clothing against hot water splashes: from bench scale test to instrumented manikin test.

Science.gov (United States)

Lu, Yehu; Song, Guowen; Wang, Faming

2015-03-01

Hot liquid hazards existing in work environments are shown to be a considerable risk for industrial workers. In this study, the predicted protection from fabric was assessed by a modified hot liquid splash tester. In these tests, conditions with and without an air spacer were applied. The protective performance of a garment exposed to hot water spray was investigated by a spray manikin evaluation system. Three-dimensional body scanning technique was used to characterize the air gap size between the protective clothing and the manikin skin. The relationship between bench scale test and manikin test was discussed and the regression model was established to predict the overall percentage of skin burn while wearing protective clothing. The results demonstrated strong correlations between bench scale test and manikin test. Based on these studies, the overall performance of protective clothing against hot water spray can be estimated on the basis of the results of the bench scale hot water splashes test and the information of air gap size entrapped in clothing. The findings provide effective guides for the design and material selection while developing high performance protective clothing. Published by Oxford University Press on behalf of the British Occupational Hygiene Society 2014.

Cambridge Rocketry Simulator – A Stochastic Six-Degrees-of-Freedom Rocket Flight Simulator

Directory of Open Access Journals (Sweden)

Willem J. Eerland

2017-02-01

Full Text Available The Cambridge Rocketry Simulator can be used to simulate the flight of unguided rockets for both design and operational applications. The software consists of three parts: The first part is a GUI that enables the user to design a rocket. The second part is a verified and peer-reviewed physics model that simulates the rocket flight. This includes a Monte Carlo wrapper to model the uncertainty in the rocket’s dynamics and the atmospheric conditions. The third part generates visualizations of the resulting trajectories, including nominal performance and uncertainty analysis, e.g. a splash-down region with confidence bounds. The project is available on SourceForge, and is written in Java (GUI, C++ (simulation core, and Python (visualization. While all parts can be executed from the GUI, the three components share information via XML, accommodating modifications, and re-use of individual components.

Nuclear Application Programs Development and Integration for a Simulator

Energy Technology Data Exchange (ETDEWEB)

Park, Hyun-Joon; Lee, Tae-Woo [KEPCO Engineering and Construction Co., Deajeon (Korea, Republic of)

2016-10-15

KEPCO E and C participated in the NAPS (Nuclear Application Programs) development project for BNPP (Barakah Nuclear Power Plant) simulator. The 3KEY MASTER™ was adopted for this project, which is comprehensive simulation platform software developed by WSC (Western Services Corporation) for the development, and control of simulation software. The NAPS based on actual BNPP project was modified in order to meet specific requirements for nuclear power plant simulators. Considerations regarding software design for BNPP simulator and interfaces between the 3KM platform and application programs are discussed. The repeatability is one of functional requirements for nuclear power plant simulators. In order to migrate software from actual plants to simulators, software functions for storing and retrieving plant conditions and program variables should be implemented. In addition, software structures need to be redesigned to meet the repeatability, and source codes developed for actual plants would have to be optimized to reflect simulator’s characteristics as well. The synchronization is an important consideration to integrate external application programs into the 3KM simulator.

Defense Coastal/Estuarine Research Program (DCERP)

Science.gov (United States)

2007-09-19

activities, splash points and Landing Craft Air Cushion (LCAC) operations) and non-military Base activities (e.g., sewage treatment , storm water runoff and...We will measure the metabolism of benthic microalgae, the water column, eelgrass, and any dominant macroalgae by developing series of photosynthesis...activities (storm water control and sewage treatment ). Defense Coastal/Estuarine Research Program (DCERP) Research Plan DCERP Research Plan 32 September 19

Field: A Program for Simulating Ultrasound Systems

DEFF Research Database (Denmark)

Jensen, Jørgen Arendt

1997-01-01

A program for the simulation of ultrasound systems is presented.It is based on the Tupholme-Stepanishen method, and is fastbecause of the use of a far-field approximation. Any kind oftransducer geometry and excitation can be simulated, and bothpulse-echo and continuous wave fields can be calculated...... for bothtransmit and pulse-echo. Dynamic apodization and focusing arehandled through time lines, and different focusingschemes can be simulated. The versatility of the program isensured by interfacing it to Matlab. All routines are calleddirectly from Matlab, and all Matlab features can be used. Thismakes...

A study on entrapment: splashing of liquid UO2 over small sodium volumes

International Nuclear Information System (INIS)

Schins, H.; Klein, K.; Jorzik, E.

1978-01-01

Three experiments were done in which each time more than 1 kg of liqid UO 2 was splashed over a plate in which different stainless steel cups full of sodium were contained. No whatsoever indication of entrapment of sodium could be found. The pressure tests indicate up to 1,8 atm and they relax in some second time. These pressure diagrams have been satisfactorily analysed as indicating a sodium vapor formation. In the third experiment e.g. the quenching of 800 g UO 2 in 720 g of sodium in a closed volume of argon of 225 l will provide the requested maximum pressure

Development of a safety and regulation systems simulation program II

International Nuclear Information System (INIS)

1985-05-01

This report describes the development of a safety and regulation systems simulation program under contract to the Atomic Energy Control Board of Canada. A systems logic interaction simulation (SLISIM) program was developed for the AECB's HP-1000 computer which operates in the interactive simulation (INSIM) program environment. The SLISIM program simulates the spatial neutron dynamics, the regulation of the reactor power and in this version the CANDU-PHW 600 MW(e) computerized shutdown systems' trip parameters. The modular concept and interactive capability of the INSIM environment provides the user with considerable flexibility of the setup and control of the simulation

Application of Nuclear Application Programs to APR1400 Simulator

International Nuclear Information System (INIS)

Hwang, Do Hyun; Lee, Myeong Soo; Hong, Jin Hyuk

2012-01-01

Advanced Power Reactor 1400MWe (APR1400) simulator has been developed and installed at Kori Training Center for operators of ShinKori no.3, 4 nuclear power plant by Korea Hydro and Nuclear Power,s Central Research Institute (KHNP CRI). NAPS (Nuclear Application Programs) is a computerbased system which provides operators with past and real-time information for monitoring and controlling NSSS (Nuclear Steam Supply System), BOP (Balance Of Plant) and Electric system. NAPS consists of several programs such as COLSS (Core Operating Limit Supervisory System), SPADES+ (Safety Parameter Display and Evaluation System), CEA (Control Element Assembly) Application Program, and so on. Each program makes calculations based on its own algorithm and provides information available for operation. In order to use NAPS programs with a simulator even though they are being used in a real plant, they should be modified to add several simulation functions such as reset, snap, run/freeze and backtrack required by ANSI/ANS-3.5 to the original NAPS functionality. On top of that, interfacing programs should be developed for the data communication between respective NAPS programs and simulator sever. The purpose of this paper is to provide the overall architecture of the communication system between NAPS and simulator model, and to describe the method to apply NAPS to APR1400 simulator

LHC Beam Splash seen by the ATLAS detector - 7 Apr 2015 - Run 260466 - LB 731 - Event 16848

CERN Multimedia

ATLAS, EXPERIMENT

2015-01-01

Event display of a collimator "splash" event seen by the ATLAS experiment in LHC Run-2, on Tuesday April the 7th 2015: event 16848, run 260466. The collimator position is 140m in front of the ATLAS interaction point. The figure on the left shows an axial view of the various components of the ATLAS detector. The figure on the right shows the energy deposits in the cells of the ATLAS calorimeter.

Off-line programming and simulation in handling nuclear components

International Nuclear Information System (INIS)

Baker, C.P.

1993-10-01

IGRIP was used to create a simulation of the robotic workcell design for handling components at the PANTEX nuclear arms facility. This initial simulation identified problems with the customer's proposed worker layout, and allowed a correction to be proposed. Refinement of the IGRIP simulation allowed the design and construction of a workcell mock-up and accurate off-line programming of the system. IGRIP's off-line programming capabilities are being used to develop the motion control code for the workcell. PNLs success in this area suggests that simulation and off-line programming may be valuable tools for developing robotics in some automation resistant industries

Quench Simulation Studies: Program documentation of SPQR

CERN Document Server

Sonnemann, F

2001-01-01

Quench experiments are being performed on prototypes of the superconducting magnets and busbars to determine the adequate design and protection. Many tests can only be understood correctly with the help of quench simulations that model the thermo-hydraulic and electrodynamic processes during a quench. In some cases simulations are the only method to scale the experimental results of prototype measurements to match the situation of quenching superconducting elements in the LHC. This note introduces the theoretical quench model and the use of the simulation program SPQR (Simulation Program for Quench Research), which has been developed to compute the quench process in superconducting magnets and busbars. The model approximates the heat balance equation with the finite difference method including the temperature dependence of the material parameters. SPQR allows the simulation of longitudinal quench propagation along a superconducting cable, the transverse propagation between adjacent conductors, heat transfer i...

Conducting Simulation Studies in the R Programming Environment.

Science.gov (United States)

Hallgren, Kevin A

2013-10-12

Simulation studies allow researchers to answer specific questions about data analysis, statistical power, and best-practices for obtaining accurate results in empirical research. Despite the benefits that simulation research can provide, many researchers are unfamiliar with available tools for conducting their own simulation studies. The use of simulation studies need not be restricted to researchers with advanced skills in statistics and computer programming, and such methods can be implemented by researchers with a variety of abilities and interests. The present paper provides an introduction to methods used for running simulation studies using the R statistical programming environment and is written for individuals with minimal experience running simulation studies or using R. The paper describes the rationale and benefits of using simulations and introduces R functions relevant for many simulation studies. Three examples illustrate different applications for simulation studies, including (a) the use of simulations to answer a novel question about statistical analysis, (b) the use of simulations to estimate statistical power, and (c) the use of simulations to obtain confidence intervals of parameter estimates through bootstrapping. Results and fully annotated syntax from these examples are provided.

A survey of electric and hybrid vehicle simulation programs

Science.gov (United States)

Bevan, J.; Heimburger, D. A.; Metcalfe, M. A.

1978-01-01

Results of a survey conducted within the United States to determine the extent of development and capabilities of automotive performance simulation programs suitable for electric and hybrid vehicle studies are summarized. Altogether, 111 programs were identified as being in a usable state. The complexity of the existing programs spans a range from a page of simple desktop calculator instructions to 300,000 lines of a high-level programming language. The capability to simulate electric vehicles was most common, heat-engines second, and hybrid vehicles least common. Batch-operated programs are slightly more common than interactive ones, and one-third can be operated in either mode. The most commonly used language was FORTRAN, the language typically used by engineers. The higher-level simulation languages (e.g. SIMSCRIPT, GPSS, SIMULA) used by "model builders" were conspicuously lacking.

The TAO Accelerator Simulation Program

CERN Document Server

Sagan, David

2005-01-01

A new accelerator design and analysis simulation environment based on the BMAD relativistic charged particle dynamics library is in development at Cornell University. Called TAO (Tool for Accelerator Optimization), it is a machine independent program that implements the essential ingredients needed to solve simulation problems. This includes the ability to: 1. Design lattices subject to constraints, 2. Simulate errors and changes in machine parameters, and 3. Simulate machine commissioning including simulating data measurement and correction. TAO is designed to be easily customizable so that extending it to solve new and different problems is straight forward. The capability to simultaneously model multiple accelerator lattices, both linacs and storage rings, and injection from one lattice to another allows for the design and commissioning of large multi stage accelerators. It can also simultaneously model multiple configurations of a single lattice. Single particle, particle beam and macroparticle tracking i...

Conducting Simulation Studies in the R Programming Environment

Directory of Open Access Journals (Sweden)

Kevin A. Hallgren

2013-10-01

Full Text Available Simulation studies allow researchers to answer specific questions about data analysis, statistical power, and best-practices for obtainingaccurate results in empirical research. Despite the benefits that simulation research can provide, many researchers are unfamiliar with available tools for conducting their own simulation studies. The use of simulation studies need not be restricted toresearchers with advanced skills in statistics and computer programming, and such methods can be implemented by researchers with a variety of abilities and interests. The present paper provides an introduction to methods used for running simulationstudies using the R statistical programming environment and is written for individuals with minimal experience running simulation studies or using R. The paper describes the rationale and benefits of using simulations and introduces R functions relevant for many simulation studies. Three examples illustrate different applications for simulation studies, including (a the use of simulations to answer a novel question about statistical analysis, (b the use of simulations to estimate statistical power, and (c the use of simulations to obtain confidence intervals of parameter estimates throughbootstrapping. Results and fully annotated syntax from these examples are provided.

Simulator: A Pilot Interactive Simulation Program for Use in Teaching Public Relations.

Science.gov (United States)

Pavlik, John V.

An interactive simulation program was developed for use in teaching students how to handle public relations problems. The program user is placed in the role of assistant newsletter editor, facing a series of decision-making situations. Each choice the user makes affects the subsequent reality created by the program, which is designed to provide…

SimZones: An Organizational Innovation for Simulation Programs and Centers.

Science.gov (United States)

Roussin, Christopher J; Weinstock, Peter

2017-08-01

The complexity and volume of simulation-based learning programs have increased dramatically over the last decade, presenting several major challenges for those who lead and manage simulation programs and centers. The authors present five major issues affecting the organization of simulation programs: (1) supporting both single- and double-loop learning experiences; (2) managing the training of simulation teaching faculty; (3) optimizing the participant mix, including individuals, professional groups, teams, and other role-players, to ensure learning; (4) balancing in situ, node-based, and center-based simulation delivery; and (5) organizing simulation research and measuring value. They then introduce the SimZones innovation, a system of organization for simulation-based learning, and explain how it can alleviate the problems associated with these five issues.Simulations are divided into four zones (Zones 0-3). Zone 0 simulations include autofeedback exercises typically practiced by solitary learners, often using virtual simulation technology. Zone 1 simulations include hands-on instruction of foundational clinical skills. Zone 2 simulations include acute situational instruction, such as clinical mock codes. Zone 3 simulations involve authentic, native teams of participants and facilitate team and system development.The authors also discuss the translation of debriefing methods from Zone 3 simulations to real patient care settings (Zone 4), and they illustrate how the SimZones approach can enable the development of longitudinal learning systems in both teaching and nonteaching hospitals. The SimZones approach was initially developed in the context of the Boston Children's Hospital Simulator Program, which the authors use to illustrate this innovation in action.

Water Quality Analysis Simulation Program (WASP)

Science.gov (United States)

The Water Quality Analysis Simulation Program (WASP) model helps users interpret and predict water quality responses to natural phenomena and manmade pollution for various pollution management decisions.

Intelligent Flight Control Simulation Research Program

National Research Council Canada - National Science Library

Stolarik, Brian

2007-01-01

...). Under the program, entitled "Intelligent Flight Control Simulation Research Laboratory," a variety of technologies were investigated or developed during the course of the research for AFRL/VAC...

Parallel programming with Easy Java Simulations

Science.gov (United States)

Esquembre, F.; Christian, W.; Belloni, M.

2018-01-01

Nearly all of today's processors are multicore, and ideally programming and algorithm development utilizing the entire processor should be introduced early in the computational physics curriculum. Parallel programming is often not introduced because it requires a new programming environment and uses constructs that are unfamiliar to many teachers. We describe how we decrease the barrier to parallel programming by using a java-based programming environment to treat problems in the usual undergraduate curriculum. We use the easy java simulations programming and authoring tool to create the program's graphical user interface together with objects based on those developed by Kaminsky [Building Parallel Programs (Course Technology, Boston, 2010)] to handle common parallel programming tasks. Shared-memory parallel implementations of physics problems, such as time evolution of the Schrödinger equation, are available as source code and as ready-to-run programs from the AAPT-ComPADRE digital library.

Survey of outcomes in a faculty development program on simulation pedagogy.

Science.gov (United States)

Roh, Young Sook; Kim, Mi Kang; Tangkawanich, Thitiarpha

2016-06-01

Although many nursing programs use simulation as a teaching-learning modality, there are few systematic approaches to help nursing educators learn this pedagogy. This study evaluates the effects of a simulation pedagogy nursing faculty development program on participants' learning perceptions using a retrospective pre-course and post-course design. Sixteen Thai participants completed a two-day nursing faculty development program on simulation pedagogy. Thirteen questionnaires were used in the final analysis. The participants' self-perceived learning about simulation teaching showed significant post-course improvement. On a five-point Likert scale, the composite mean attitude, subjective norm, and perceived behavioral control scores, as well as intention to use a simulator, showed a significant post-course increase. A faculty development program on simulation pedagogy induced favorable learning and attitudes. Further studies must test how faculty performance affects the cognitive, emotional, and social dimensions of learning in a simulation-based learning domain. © 2015 Wiley Publishing Asia Pty Ltd.

The development of fast simulation program for marine reactor parameters

International Nuclear Information System (INIS)

Chen Zhiyun; Hao Jianli; Chen Wenzhen

2012-01-01

Highlights: ► The simplified physical and mathematical models are proposed for a marine reactor system. ► A program is developed with Simulink module and Matlab file. ► The program developed has the merit of easy input preparation, output processing and fast running. ► The program can be used for the fast simulation of marine reactor parameters on the operating field. - Abstract: The fast simulation program for marine reactor parameters is developed based on the Simulink simulating software according to the characteristics of marine reactor with requirement of maneuverability and acute and fast response. The simplified core physical and thermal model, pressurizer model, steam generator model, control rod model, reactivity model and the corresponding Simulink modules are established. The whole program is developed by coupling all the Simulink modules. Two typical transient processes of marine reactor with fast load increase at low power level and load rejection at high power level are adopted to verify the program. The results are compared with those of Relap5/Mod3.2 with good consistency, and the program runs very fast. It is shown that the program is correct and suitable for the fast and accurate simulation of marine reactor parameters on the operating field, which is significant to the marine reactor safe operation.

Program BETA for simulation of particle decays and reactions

International Nuclear Information System (INIS)

Takhtamyshev, G.G.; Merkulova, T.A.

1997-01-01

Program BETA is designed for simulation of particle decays and reactions. The program also produces integration over the phase space and decay rate or the reaction cross section are calculated as a result of such integration. At the simulation process the adaptive random number generator SMART may be used, what is found to be useful for some difficult cases

Simulation of droplet impact onto a deep pool for large Froude numbers in different open-source codes

Science.gov (United States)

Korchagova, V. N.; Kraposhin, M. V.; Marchevsky, I. K.; Smirnova, E. V.

2017-11-01

A droplet impact on a deep pool can induce macro-scale or micro-scale effects like a crown splash, a high-speed jet, formation of secondary droplets or thin liquid films, etc. It depends on the diameter and velocity of the droplet, liquid properties, effects of external forces and other factors that a ratio of dimensionless criteria can account for. In the present research, we considered the droplet and the pool consist of the same viscous incompressible liquid. We took surface tension into account but neglected gravity forces. We used two open-source codes (OpenFOAM and Gerris) for our computations. We review the possibility of using these codes for simulation of processes in free-surface flows that may take place after a droplet impact on the pool. Both codes simulated several modes of droplet impact. We estimated the effect of liquid properties with respect to the Reynolds number and Weber number. Numerical simulation enabled us to find boundaries between different modes of droplet impact on a deep pool and to plot corresponding mode maps. The ratio of liquid density to that of the surrounding gas induces several changes in mode maps. Increasing this density ratio suppresses the crown splash.

Misrepresentation of hydro-erosional processes in rainfall simulations using disturbed soil samples

Science.gov (United States)

Thomaz, Edivaldo L.; Pereira, Adalberto A.

2017-06-01

Interrill erosion is a primary soil erosion process which consists of soil detachment by raindrop impact and particle transport by shallow flow. Interill erosion affects other soil erosion sub-processes, e.g., water infiltration, sealing, crusting, and rill initiation. Interrill erosion has been widely studied in laboratories, and the use of a sieved soil, i.e., disturbed soil, has become a standard method in laboratory experiments. The aims of our study are to evaluate the hydro-erosional response of undisturbed and disturbed soils in a laboratory experiment, and to quantify the extent to which hydraulic variables change during a rainstorm. We used a splash pan of 0.3 m width, 0.45 m length, and 0.1 m depth. A rainfall simulation of 58 mm h- 1 lasting for 30 min was conducted on seven replicates of undisturbed and disturbed soils. During the experiment, several hydro-physical parameters were measured, including splashed sediment, mean particle size, runoff, water infiltration, and soil moisture. We conclude that use of disturbed soil samples results in overestimation of interrill processes. Of the nine assessed parameters, four displayed greater responses in the undisturbed soil: infiltration, topsoil shear strength, mean particle size of eroded particles, and soil moisture. In the disturbed soil, five assessed parameters displayed greater responses: wash sediment, final runoff coefficient, runoff, splash, and sediment yield. Therefore, contextual soil properties are most suitable for understanding soil erosion, as well as for defining soil erodibility.

Simulation program for multiple expansion Stirling machines

International Nuclear Information System (INIS)

Walker, G.; Weiss, M.; Fauvel, R.; Reader, G.; Bingham, E.R.

1992-01-01

Multiple expansion Stirling machines have been a topic of interest at the University of Calgary for some years. Recently a second-order computer simulation program with integral graphics package for Stirling cryocoolers with up to four stages of expansion were developed and made available to the Stirling community. Adaptation of the program to multiple expansion Stirling power systems is anticipated. This paper briefly introduces the program and presents a specimen result

Calibration of a micro simulation program for a Chinese city

NARCIS (Netherlands)

Jie, L.; Fangfang, Z.; Van Zuylen, H.J.; Shoufeng, L.

2011-01-01

Micro simulation programs are often used to assess the quality of traffic conditions. They are especially suited to evaluate possible control scenarios in advance, so that the scenarios can be selected and optimized before implementation. Of course, the simulation programs should be valid for the

A simulation model of IT risk on program trading

Science.gov (United States)

Xia, Bingying; Jiang, Wenbao; Luo, Guangxuan

2015-12-01

The biggest difficulty for Program trading IT risk measures lies in the loss of data, in view of this situation, the current scholars approach is collecting court, network and other public media such as all kinds of accident of IT both at home and abroad for data collection, and the loss of IT risk quantitative analysis based on this database. However, the IT risk loss database established by this method can only fuzzy reflect the real situation and not for real to make fundamental explanation. In this paper, based on the study of the concept and steps of the MC simulation, we use computer simulation method, by using the MC simulation method in the "Program trading simulation system" developed by team to simulate the real programming trading and get the IT risk loss of data through its IT failure experiment, at the end of the article, on the effectiveness of the experimental data is verified. In this way, better overcome the deficiency of the traditional research method and solves the problem of lack of IT risk data in quantitative research. More empirically provides researchers with a set of simulation method are used to study the ideas and the process template.

Specs: Simulation Program for Electronic Circuits and Systems

Science.gov (United States)

de Geus, Aart Jan

Simulation tools are central to the development and verification of very large scale integrated circuits. Circuit simulation has been used for over two decades to verify the behavior of designs. Recently the introduction of switch-level simulators which model MOS transistors in terms of switches has helped to overcome the long runtimes associated with full circuit simulation. Used strictly for functional verification and fault simulation, switch -level simulation can only give very rough estimates of the timing of a circuit. In this dissertation an approach is presented which adds a timing capability to switch-level simulators at relatively little extra CPU cost. A new logic state concept is introduced which consists of a set of discrete voltage steps. Signals are known only in terms of these states thus allowing all current computations to be table driven. State changes are scheduled in the same fashion as in the case of gate-level simulators, making the simulator event-driven. The simulator is of mixed-mode nature in that it can model portions of a design at either the gate or transistor level. In order to represent the "unknown" state, a signal consists of both an upper and a lower bound defining a signal envelope. Both bounds are expressed in terms of states. In order to speed up the simulation, MOS networks are subdivided in small pull-up and pull-down transistor configurations that can be preanalysed and prepared for fast evaluation during the simulation. These concepts have been implemented in the program SPECS (Simulation Program For Electronic Circuits and Systems) and examples of simulations are given.

Building Interactive Simulations in Web Pages without Programming.

Science.gov (United States)

Mailen Kootsey, J; McAuley, Grant; Bernal, Julie

2005-01-01

A software system is described for building interactive simulations and other numerical calculations in Web pages. The system is based on a new Java-based software architecture named NumberLinX (NLX) that isolates each function required to build the simulation so that a library of reusable objects could be assembled. The NLX objects are integrated into a commercial Web design program for coding-free page construction. The model description is entered through a wizard-like utility program that also functions as a model editor. The complete system permits very rapid construction of interactive simulations without coding. A wide range of applications are possible with the system beyond interactive calculations, including remote data collection and processing and collaboration over a network.

PSSGP : Program for Simulation of Stationary Gaussian Processes

DEFF Research Database (Denmark)

Sørensen, John Dalsgaard

This report describes the computer program PSSGP. PSSGP can be used to simulate realizations of stationary Gaussian stochastic processes. The simulation algorithm can be coupled with some applications. One possibility is to use PSSGP to estimate the first-passage density function of a given system...

Contrasting the capabilities of building energy performance simulation programs

Energy Technology Data Exchange (ETDEWEB)

Crawley, Drury B. [US Department of Energy, Washington, DC (United States); Hand, Jon W. [University of Strathclyde, Glasgow, Scotland (United Kingdom). Energy Systems Research Unit; Kummert, Michael [University of Wisconsin-Madison (United States). Solar Energy Laboratory; Griffith, Brent T. [National Renewable Energy Laboratory, Golden, CO (United States)

2008-04-15

For the past 50 years, a wide variety of building energy simulation programs have been developed, enhanced and are in use throughout the building energy community. This paper is an overview of a report, which provides up-to-date comparison of the features and capabilities of twenty major building energy simulation programs. The comparison is based on information provided by the program developers in the following categories: general modeling features; zone loads; building envelope and daylighting and solar; infiltration, ventilation and multizone airflow; renewable energy systems; electrical systems and equipment; HVAC systems; HVAC equipment; environmental emissions; economic evaluation; climate data availability, results reporting; validation; and user interface, links to other programs, and availability. (author)

Agent Programming Languages and Logics in Agent-Based Simulation

DEFF Research Database (Denmark)

Larsen, John

2018-01-01

and social behavior, and work on verification. Agent-based simulation is an approach for simulation that also uses the notion of agents. Although agent programming languages and logics are much less used in agent-based simulation, there are successful examples with agents designed according to the BDI...

STEM image simulation with hybrid CPU/GPU programming

International Nuclear Information System (INIS)

Yao, Y.; Ge, B.H.; Shen, X.; Wang, Y.G.; Yu, R.C.

2016-01-01

STEM image simulation is achieved via hybrid CPU/GPU programming under parallel algorithm architecture to speed up calculation on a personal computer (PC). To utilize the calculation power of a PC fully, the simulation is performed using the GPU core and multi-CPU cores at the same time to significantly improve efficiency. GaSb and an artificial GaSb/InAs interface with atom diffusion have been used to verify the computation. - Highlights: • STEM image simulation is achieved by hybrid CPU/GPU programming under parallel algorithm architecture to speed up the calculation in the personal computer (PC). • In order to fully utilize the calculation power of the PC, the simulation is performed by GPU core and multi-CPU cores at the same time so efficiency is improved significantly. • GaSb and artificial GaSb/InAs interface with atom diffusion have been used to verify the computation. The results reveal some unintuitive phenomena about the contrast variation with the atom numbers.

STEM image simulation with hybrid CPU/GPU programming

Energy Technology Data Exchange (ETDEWEB)

Yao, Y., E-mail: yaoyuan@iphy.ac.cn; Ge, B.H.; Shen, X.; Wang, Y.G.; Yu, R.C.

2016-07-15

STEM image simulation is achieved via hybrid CPU/GPU programming under parallel algorithm architecture to speed up calculation on a personal computer (PC). To utilize the calculation power of a PC fully, the simulation is performed using the GPU core and multi-CPU cores at the same time to significantly improve efficiency. GaSb and an artificial GaSb/InAs interface with atom diffusion have been used to verify the computation. - Highlights: • STEM image simulation is achieved by hybrid CPU/GPU programming under parallel algorithm architecture to speed up the calculation in the personal computer (PC). • In order to fully utilize the calculation power of the PC, the simulation is performed by GPU core and multi-CPU cores at the same time so efficiency is improved significantly. • GaSb and artificial GaSb/InAs interface with atom diffusion have been used to verify the computation. The results reveal some unintuitive phenomena about the contrast variation with the atom numbers.

Development of Simulator Maintenance Engineer Qualification Program Draft

International Nuclear Information System (INIS)

Chung, Kyung Hun

2010-01-01

As of 2009, KHNP has currently seven full scope simulators that are used for training of Nuclear Power Plant (NPP) Operators. Well-trained Simulator Maintenance Engineers (SME) are required to support these simulators. These SMEs will maintain and address any issues identified or any changes required for keep up the simulator with their respective plant sites. These issues will be identified as Simulator Discrepancy Reports (DR) or Work Order (WO) by the simulator operation personnel in KHNP. The simulator maintenance is a very complex. The simulator consists of many areas of process and requires experts in software modeling for different processes such as Neutronics, thermohydraulics, Logics, control, Electrical systems and computer systems as well as hardware subjects such as I and C, I/O, computers, etc. All these areas need experts the subject expertise need to be divided among SME's. In other word the SME's need to be trained for different expertise as well as having different level of SME's. KHNP has seen the need to outsource the maintenance work for these complex simulators. To have one company concentrating on this work will have many benefits such as: · Provides proper and well trained experts · Maintains consistent support personnel · Maintains the maintenance history for the simulator · Coordinates and Maintains the knowledge in house · The simulator maintenance will be consistent In order to accomplish the goals, KEPCO RI has recognized that there is a need for a program to adequately train and qualify the SME's. KEPCO RI and GSE, which has provided 6 simulators among 7 NPP simulators in Korea, have jointly developed this Simulator Maintenance Engineer Qualification Program (SMEQP). After issue of this plan, KEPCO RI will maintain and modify as needed periodically to meet the goals and purpose of the plan

SIMUL - a program for the simulation of interactions in the streamer chamber RISK

International Nuclear Information System (INIS)

Friebel, W.; Gajewski, J.; Halm, I.

1976-08-01

A program for the simulation of interactions in the streamer chamber RISK is described. This program allows first investigations and tests for planning and preparing experiments. In the program the trajectories of all particles taking part in the interaction are computed. Selected points are projected onto film planes serving as measurement points for the use in the geometrical reconstruction. The program is used for testing a geometry program. But it also seems to be very helpful in investigating counter and trigger constellations and in the calculation of counting rates and trigger effectivities. (author)

Gstat: a program for geostatistical modelling, prediction and simulation

Science.gov (United States)

Pebesma, Edzer J.; Wesseling, Cees G.

1998-01-01

Gstat is a computer program for variogram modelling, and geostatistical prediction and simulation. It provides a generic implementation of the multivariable linear model with trends modelled as a linear function of coordinate polynomials or of user-defined base functions, and independent or dependent, geostatistically modelled, residuals. Simulation in gstat comprises conditional or unconditional (multi-) Gaussian sequential simulation of point values or block averages, or (multi-) indicator sequential simulation. Besides many of the popular options found in other geostatistical software packages, gstat offers the unique combination of (i) an interactive user interface for modelling variograms and generalized covariances (residual variograms), that uses the device-independent plotting program gnuplot for graphical display, (ii) support for several ascii and binary data and map file formats for input and output, (iii) a concise, intuitive and flexible command language, (iv) user customization of program defaults, (v) no built-in limits, and (vi) free, portable ANSI-C source code. This paper describes the class of problems gstat can solve, and addresses aspects of efficiency and implementation, managing geostatistical projects, and relevant technical details.

Effects of a System Thinking-Based Simulation Program for Congestive Heart Failure.

Science.gov (United States)

Kim, Hyeon-Young; Yun, Eun Kyoung

2018-03-01

This study evaluated a system thinking-based simulation program for the care of patients with congestive heart failure. Participants were 67 undergraduate nursing students from a nursing college in Seoul, South Korea. The experimental group was given a 4-hour system-thinking program and a 2-hour simulation program, whereas the control group had a 4-hour case study and a 2-hour simulation program. There were significant improvements in critical thinking in both groups, but no significant group differences between educational methods (F = 3.26, P = .076). Problem-solving ability in the experimental group was significantly higher than in the control group (F = 5.04, P = .028). Clinical competency skills in the experimental group were higher than in the control group (t = 2.12, P = .038). A system thinking-based simulation program is a more effective learning method in terms of problem-solving ability and clinical competency skills compared to the existing simulation program. Further research using a longitudinal study is needed to test the long-term effect of the intervention and apply it to the nursing curriculum.

Graphical programming: On-line robot simulation for telerobotic control

International Nuclear Information System (INIS)

McDonald, M.J.; Palmquist, R.D.

1993-01-01

Sandia has developed an advanced operational control system approach, caged Graphical Programming, to design and operate robotic waste cleanup and other hazardous duty robotic systems. The Graphical Programming approach produces robot systems that are faster to develop and use, safer in operation, and cheaper overall than altemative teleoperation or autonomous robot control systems. The Graphical Programming approach uses 3-D visualization and simulation software with intuitive operator interfaces for the programming and control of complex robotic systems. Graphical Programming Supervisor software modules allow an operator to command and simulate complex tasks in a graphic preview mode and, when acceptable, command the actual robots and monitor their motions with the graphic system. Graphical Progranuning Supervisors maintain registration with the real world and allow the robot to perform tasks that cannot be accurately represented with models alone by using a combination of model and sensor-based control. This paper describes the Graphical Programming approach, several example control systems that use Graphical Programming, and key features necessary for implementing successful Graphical Programming systems

SIMPSON: A general simulation program for solid-state NMR spectroscopy

Science.gov (United States)

Bak, Mads; Rasmussen, Jimmy T.; Nielsen, Niels Chr.

2011-12-01

A computer program for fast and accurate numerical simulation of solid-state NMR experiments is described. The program is designed to emulate a NMR spectrometer by letting the user specify high-level NMR concepts such as spin systems, nuclear spin interactions, RF irradiation, free precession, phase cycling, coherence-order filtering, and implicit/explicit acquisition. These elements are implemented using the Tel scripting language to ensure a minimum of programming overhead and direct interpretation without the need for compilation, while maintaining the flexibility of a full-featured programming language. Basicly, there are no intrinsic limitations to the number of spins, types of interactions, sample conditions (static or spinning, powders, uniaxially oriented molecules, single crystals, or solutions), and the complexity or number of spectral dimensions for the pulse sequence. The applicability ranges from simple ID experiments to advanced multiple-pulse and multiple-dimensional experiments, series of simulations, parameter scans, complex data manipulation/visualization, and iterative fitting of simulated to experimental spectra. A major effort has been devoted to optimizing the computation speed using state-of-the-art algorithms for the time-consuming parts of the calculations implemented in the core of the program using the C programming language. Modification and maintenance of the program are facilitated by releasing the program as open source software (General Public License) currently at http://nmr.imsb.au.dk. The general features of the program are demonstrated by numerical simulations of various aspects for REDOR, rotational resonance, DRAMA, DRAWS, HORROR, C7, TEDOR, POST-C7, CW decoupling, TPPM, F-SLG, SLF, SEMA-CP, PISEMA, RFDR, QCPMG-MAS, and MQ-MAS experiments.

Military nuclear activities. The simulation program

International Nuclear Information System (INIS)

Delpuech, A.

2000-01-01

The durability of the French nuclear weapon dissuasion has to integrate two kind of problems: the geopolitical situation with the comprehensive nuclear test ban treaty (CTBT) and the aging of weapons. The replacement of decayed weapons requires a complete safety and reliability validation of the new weapons which is performed using simulation. This paper gives a brief presentation of the simulation program and of the technical means developed by the military division of the French atomic energy commission (CEA-DAM): the Airix X-ray radiography installation and the 'megajoule' laser facility. (J.S.)

ACCURATE OH MASER POSITIONS FROM THE SPLASH PILOT REGION

Energy Technology Data Exchange (ETDEWEB)

Qiao, Hai-Hua; Shen, Zhi-Qiang [Shanghai Astronomical Observatory, Chinese Academy of Sciences, 80 Nandan Road, Shanghai, 200030 (China); Walsh, Andrew J.; Jordan, Christopher H. [International Centre for Radio Astronomy Research, Curtin University, GPO Box U1987, Perth WA 6845 (Australia); Green, James A. [CSIRO Astronomy and Space Science, Australia Telescope National Facility, PO Box 76, Epping, NSW 2121 (Australia); Breen, Shari L. [Sydney Institute for Astronomy (SIfA), School of Physics, University of Sydney, NSW 2006 (Australia); Dawson, J. R. [Department of Physics and Astronomy and MQ Research Centre in Astronomy, Astrophysics and Astrophotonics, Macquarie University, NSW 2109 (Australia); Ellingsen, Simon P. [School of Physical Sciences, Private Bag 37,University of Tasmania, Hobart 7001, TAS (Australia); Gómez, José F. [Instituto de Astrofísica de Andalucía, CSIC, Glorieta de la Astronomía s/n, E-18008, Granada (Spain); Lowe, Vicki; Jones, Paul A., E-mail: qiaohh@shao.ac.cn [Department of Astrophysics and Optic, School of Physics, University of New South Wales, Sydney, NSW 2052 (Australia)

2016-12-01

We report on high spatial resolution observations, using the Australia Telescope Compact Array (ATCA), of ground-state OH masers. These observations were carried out toward 196 pointing centers previously identified in the Southern Parkes Large-Area Survey in Hydroxyl (SPLASH) pilot region, between Galactic longitudes of 334° and 344° and Galactic latitudes of −2° and +2°. Supplementing our data with data from the MAGMO (Mapping the Galactic Magnetic field through OH masers) survey, we find maser emission toward 175 of the 196 target fields. We conclude that about half of the 21 nondetections were due to intrinsic variability. Due to the superior sensitivity of the followup ATCA observations, and the ability to resolve nearby sources into separate sites, we have identified 215 OH maser sites toward the 175 fields with detections. Among these 215 OH maser sites, 111 are new detections. After comparing the positions of these 215 maser sites to the literature, we identify 122 (57%) sites associated with evolved stars (one of which is a planetary nebula), 64 (30%) with star formation, two sites with supernova remnants, and 27 (13%) of unknown origin. The infrared colors of evolved star sites with symmetric maser profiles tend to be redder than those of evolved star sites with asymmetric maser profiles, which may indicate that symmetric sources are generally at an earlier evolutionary stage.

Fusion Simulation Program Definition. Final report

International Nuclear Information System (INIS)

Cary, John R.

2012-01-01

We have completed our contributions to the Fusion Simulation Program Definition Project. Our contributions were in the overall planning with concentration in the definition of the area of Software Integration and Support. We contributed to the planning of multiple meetings, and we contributed to multiple planning documents

The implementation of full ATLAS detector simulation program

International Nuclear Information System (INIS)

Rimoldi, A.; Dell'Acqua, A.; Stavrianakou, M.; Amako, K.; Kanzaki, J.; Morita, Y.; Murakami, K.; Sasaki, T.; Saeki, T.; Ueda, I.; Tanaka, S.; Yoshida, H.

2001-01-01

The ATLAS detector is one of the most sophisticated and huge detectors ever designed up to now. A detailed, flexible and complete simulation program is needed in order to study the characteristics and possible problems of such a challenging apparatus and to answer to all raising questions in terms of physics, design optimization, etc. To cope with these needs the authors are implementing an application based on the simulation framework FADS/Goofy (Framework for ATLAS Detector Simulation /Geant4-based Object-Oriented Folly) in the Geant4 environment. The user's specific code implementation is presented in details for the different applications implemented until now, from the various components of the ATLAS spectrometer to some particular testbeam facilities. Particular emphasis is put in describing the simulation of the Muon Spectrometer and its subsystems as a test case for the implementation of the whole detector simulation program: the intrinsic complexity in the geometry description of the Muon System is one of the more demanding problems that are faced. The magnetic field handling, the physics impact in the event processing in presence of backgrounds from different sources and the implementation of different possible generators (including Pythia) are also discussed

Object oriented programming in simulation of ions transport

International Nuclear Information System (INIS)

Zhang Wenyong; Wang Tongquan; Xiao Yabin; Dai Hongyi; Chen Yuzhong

2001-01-01

Using Object Oriented Programming (OOP) method can make our program more reliable and easier to read, debug, maintain and upgrade. This paper compared FORTRAN90-the language widely used in science computing with C ++ --An Object Oriented Language, and the conclusion was made that although FORTRAN90 have many deficiencies, it can be used in Object Oriented programming. Then OOP method was used in programming of Monte Carlo simulation of ions transport and the general process of OOP was given

A computer program for scanning transmission ion microscopy simulation

International Nuclear Information System (INIS)

Wu, R.; Shen, H.; Mi, Y.; Sun, M.D.; Yang, M.J.

2005-01-01

With the installation of the Scanning Proton Microprobe system at Fudan University, we are in the process of developing a three-dimension reconstruction technique based on scanning transmission ion microscopy-computed tomography (STIM-CT). As the first step, a related computer program of STIM simulation has been established. This program is written in the Visual C++[reg], using the technique of OOP (Object Oriented Programming) and it is a standard multiple-document Windows[reg] program. It can be run with all MS Windows[reg] operating systems. The operating mode is the menu mode, using a multiple process technique. The stopping power theory is based on the Bethe-Bloch formula. In order to simplify the calculation, the improved cylindrical coordinate model was introduced in the program instead of a usual spherical or cylindrical coordinate model. The simulated results of a sample at several rotation angles are presented

LASER APPLICATIONS AND OTHER TOPICS IN QUANTUM ELECTRONICS: Dynamics of splashing of molten metals during irradiation with single CO2 laser pulses

Science.gov (United States)

Arutyunyan, R. V.; Baranov, V. Yu; Bol'shov, Leonid A.; Dolgov, V. A.; Malyuta, D. D.; Mezhevov, V. S.; Semak, V. V.

1988-03-01

An experimental investigation was made of the dynamics of the loss of the melt as a result of interaction with single-mode CO2 laser radiation pulses of 5-35 μs duration. The dynamics of splashing of the melt during irradiation with short pulses characterized by a Gaussian intensity distribution differed from that predicted by models in which the distribution of the vapor pressure was assumed to be radially homogeneous.

Validation of Multibody Program to Optimize Simulated Trajectories II Parachute Simulation with Interacting Forces

Science.gov (United States)

Raiszadeh, Behzad; Queen, Eric M.; Hotchko, Nathaniel J.

2009-01-01

A capability to simulate trajectories of multiple interacting rigid bodies has been developed, tested and validated. This capability uses the Program to Optimize Simulated Trajectories II (POST 2). The standard version of POST 2 allows trajectory simulation of multiple bodies without force interaction. In the current implementation, the force interaction between the parachute and the suspended bodies has been modeled using flexible lines, allowing accurate trajectory simulation of the individual bodies in flight. The POST 2 multibody capability is intended to be general purpose and applicable to any parachute entry trajectory simulation. This research paper explains the motivation for multibody parachute simulation, discusses implementation methods, and presents validation of this capability.

Hypofolins A - L, ent-Labdane Diterpenoids from the Roots of Hypoestes phyllostachya 'Pink Splash'.

Science.gov (United States)

Cheng, Bin; Ding, Lin-Fen; Yan, Tong; Xie, Zhang-Qiao; Zhang, Zhi-Jun; Song, Liu-Dong; Wu, Xing-De; Zhao, Qin-Shi

2018-06-01

Twelve new ent-labdane diterpenoids, hypofolins A - F (1 - 6) and hypofolins G - L (7a/7b, 8a/8b, and 9a/9b), were isolated from the roots of Hypoestes phyllostachya 'Pink Splash'. Their structures were elucidated by extensive 1D- and 2D-NMR spectroscopic and HR-MS data. The absolute configurations of 1, 2, 5, and 7a/7b were determined by single crystal X-ray diffraction and ECD analysis, as well as chemical transformations. Compounds 7a/7b, 8a/8b, and 9a/9b were isolated as three pairs of interconverting mixture of two isomers between ketone and hemiketal types. Compound 1 showed weak cytotoxicity against SMMC-7721 cell line with IC 50 value of 31.40 μm. © 2018 Wiley-VHCA AG, Zurich, Switzerland.

Nuclear Power Reactor simulator - based training program

International Nuclear Information System (INIS)

Abdelwahab, S.A.S.

2009-01-01

nuclear power stations will continue playing a major role as an energy source for electric generation and heat production in the world. in this paper, a nuclear power reactor simulator- based training program will be presented . this program is designed to aid in training of the reactor operators about the principles of operation of the plant. also it could help the researchers and the designers to analyze and to estimate the performance of the nuclear reactors and facilitate further studies for selection of the proper controller and its optimization process as it is difficult and time consuming to do all experiments in the real nuclear environment.this program is written in MATLAB code as MATLAB software provides sophisticated tools comparable to those in other software such as visual basic for the creation of graphical user interface (GUI). moreover MATLAB is available for all major operating systems. the used SIMULINK reactor model for the nuclear reactor can be used to model different types by adopting appropriate parameters. the model of each component of the reactor is based on physical laws rather than the use of look up tables or curve fitting.this simulation based training program will improve acquisition and retention knowledge also trainee will learn faster and will have better attitude

Numerical simulation of particle dynamics in storage rings using BETACOOL program

International Nuclear Information System (INIS)

Meshkov, I.N.; Pivin, R.V.; Sidorin, A.O.; Smirnov, A.V.; Trubnikov, G.V.

2006-01-01

BETACOOL program developed by JINR electron cooling group is a kit of algorithms based on common format of input and output files. The program is oriented to simulation of the ion beam dynamics in a storage ring in the presence of cooling and heating effects. The version presented in this report includes three basic algorithms: simulation of rms parameters of the ion distribution function evolution in time, simulation of the distribution function evolution using Monte-Carlo method and tracking algorithm based on molecular dynamics technique. General processes to be investigated with the program are intrabeam scattering in the ion beam, electron cooling, interaction with residual gas and internal target

BEAMPATH: a program library for beam dynamics simulation in linear accelerators

International Nuclear Information System (INIS)

Batygin, Y.K.

1992-01-01

A structured programming technique was used to develop software for space charge dominated beams investigation in linear accelerators. The method includes hierarchical program design using program independent modules and a flexible combination of modules to provide a most effective version of structure for every specific case of simulation. A modular program BEAMPATH was developed for 2D and 3D particle-in-cell simulation of beam dynamics in a structure containing RF gaps, radio-frequency quadrupoles (RFQ), multipole lenses, waveguides, bending magnets and solenoids. (author) 5 refs.; 2 figs

Modeling and simulation of melt-layer erosion during a plasma disruption

International Nuclear Information System (INIS)

Hassanein, A.; Belan, V.; Konkashbaev, I.; Nikandrov, L.; Safronov, V.; Zhitlukhin, A.; Litunovsky, V.

1997-01-01

Metallic plasma-facing components (PFCs) e.g. beryllium and tungsten, will be subjected to severe melting during plasma instabilities such as disruptions, edge-localized modes and high power excursions. Because of the greater thickness of the resulting melt layers relative to that of the surface vaporization, the potential loss of the developing melt-layer can significantly shorten PFC lifetime, severely contaminate the plasma and potentially prevent successful operation of the tokamak reactor. Mechanisms responsible for melt-layer loss during plasma instabilities are being modeled and evaluated. Of particular importance are hydrodynamic instabilities developed in the liquid layer due to various forces such as those from magnetic fields, plasma impact momentum, vapor recoil and surface tension. Another mechanism found to contribute to melt-layer splashing loss is volume bubble boiling, which can result from overheating of the liquid layer. To benchmark these models, several new experiments were designed and performed in different laboratory devices for this work; the SPLASH codes) are generally in good agreement with the experimental results. The effect of in-reactor disruption conditions, which do not exist in simulation experiments, on melt-layer erosion is discussed. (orig.)

Apollo experience report: Guidance and control systems. Engineering simulation program

Science.gov (United States)

Gilbert, D. W.

1973-01-01

The Apollo Program experience from early 1962 to July 1969 with respect to the engineering-simulation support and the problems encountered is summarized in this report. Engineering simulation in support of the Apollo guidance and control system is discussed in terms of design analysis and verification, certification of hardware in closed-loop operation, verification of hardware/software compatibility, and verification of both software and procedures for each mission. The magnitude, time, and cost of the engineering simulations are described with respect to hardware availability, NASA and contractor facilities (for verification of the command module, the lunar module, and the primary guidance, navigation, and control system), and scheduling and planning considerations. Recommendations are made regarding implementation of similar, large-scale simulations for future programs.

A simulation program for the VIRGO experiment

International Nuclear Information System (INIS)

Caron, B.; Dominjon, A.; Flaminio, R.; Marion, F.; Massonet, L.; Morand, R.; Mours, B.; Verkindt, D.; Yvert, M.

1994-07-01

Within the VIRGO experiment a simulation program is developed providing an accurate description of the interferometric antenna behaviour, taking into account all sources of noise. Besides its future use as a tool for data analysis and for the commissioning of the apparatus, the simulation helps finalizing the design of the detector. Emphasis is put at the present time on the study of the stability of optical components implied in the global feedback control system of the interferometer. (author). 5 refs., 4 figs

Massive parallel electromagnetic field simulation program JEMS-FDTD design and implementation on jasmin

International Nuclear Information System (INIS)

Li Hanyu; Zhou Haijing; Dong Zhiwei; Liao Cheng; Chang Lei; Cao Xiaolin; Xiao Li

2010-01-01

A large-scale parallel electromagnetic field simulation program JEMS-FDTD(J Electromagnetic Solver-Finite Difference Time Domain) is designed and implemented on JASMIN (J parallel Adaptive Structured Mesh applications INfrastructure). This program can simulate propagation, radiation, couple of electromagnetic field by solving Maxwell equations on structured mesh explicitly with FDTD method. JEMS-FDTD is able to simulate billion-mesh-scale problems on thousands of processors. In this article, the program is verified by simulating the radiation of an electric dipole. A beam waveguide is simulated to demonstrate the capability of large scale parallel computation. A parallel performance test indicates that a high parallel efficiency is obtained. (authors)

Developments in the electron gun simulation program, EGUN

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.

1994-11-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described

Developments in the electron gun simulation program, EGUN

Science.gov (United States)

Herrmannsfeldt, W. B.

1995-07-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described.

GENOMEPOP: A program to simulate genomes in populations

Directory of Open Access Journals (Sweden)

Carvajal-Rodríguez Antonio

2008-04-01

Full Text Available Abstract Background There are several situations in population biology research where simulating DNA sequences is useful. Simulation of biological populations under different evolutionary genetic models can be undertaken using backward or forward strategies. Backward simulations, also called coalescent-based simulations, are computationally efficient. The reason is that they are based on the history of lineages with surviving offspring in the current population. On the contrary, forward simulations are less efficient because the entire population is simulated from past to present. However, the coalescent framework imposes some limitations that forward simulation does not. Hence, there is an increasing interest in forward population genetic simulation and efficient new tools have been developed recently. Software tools that allow efficient simulation of large DNA fragments under complex evolutionary models will be very helpful when trying to better understand the trace left on the DNA by the different interacting evolutionary forces. Here I will introduce GenomePop, a forward simulation program that fulfills the above requirements. The use of the program is demonstrated by studying the impact of intracodon recombination on global and site-specific dN/dS estimation. Results I have developed algorithms and written software to efficiently simulate, forward in time, different Markovian nucleotide or codon models of DNA mutation. Such models can be combined with recombination, at inter and intra codon levels, fitness-based selection and complex demographic scenarios. Conclusion GenomePop has many interesting characteristics for simulating SNPs or DNA sequences under complex evolutionary and demographic models. These features make it unique with respect to other simulation tools. Namely, the possibility of forward simulation under General Time Reversible (GTR mutation or GTR×MG94 codon models with intra-codon recombination, arbitrary, user

MC/DC and Toggle Coverage Measurement Tool for FBD Program Simulation

Energy Technology Data Exchange (ETDEWEB)

Kim, Eui Sub; Jung, Se Jin; Kim, Jae Yeob; Yoo, Jun Beom [Konkuk University, Seoul (Korea, Republic of)

2016-05-15

The functional verification of FBD program can be implemented with various techniques such as testing and simulation. Simulation is preferable to verify FBD program, because it replicates operation of the PLC as well. The PLC is executed repeatedly as long as the controlled system is running based on scan time. Likewise, the simulation technique operates continuously and sequentially. Although engineers try to verify the functionality wholly, it is difficult to find residual errors in the design. Even if 100% functional coverage is accomplished, code coverage have 50%, which might indicate that the scenario is missing some key features of the design. Unfortunately, errors and bugs are often found in the missing points. To assure a high quality of functional verification, code coverage is important as well as functional coverage. We developed a pair tool 'FBDSim' and 'FBDCover' for FBD simulation and coverage measurement. The 'FBDSim' automatically simulates a set of FBD simulation scenarios. While the 'FBDSim' simulates the FBD program, it calculates the MC/DC and Toggle coverage and identifies unstimulated points. After FBD simulation is done, the 'FBDCover' reads the coverage results and shows the coverage with graphical feature and uncovered points with tree feature. The coverages and uncovered points can help engineers to improve the quality of simulation. We slightly dealt with the both coverages, but the coverage is dealt with more concrete and rigorous manner.

An application of object-oriented programming to process simulation

International Nuclear Information System (INIS)

Robinson, J.T.; Otaduy, P.J.

1988-01-01

This paper discusses the application of object-oriented programming to dynamic simulation of continuous processes. Processes may be modeled using this technique as a collection of objects which communicate with each other via message passing. Arriving messages invoke methods that describe the state and/or dynamic behavior of the receiving object. The objects fall into four broad categories actual plant components such as pumps, pipes, and tanks, abstract objects such as heat sources and conductors, plant systems such as flow loops, and simulation control and interface objects. This technique differs from traditional approaches to process simulation, in which the process is represented by either a system of differential equations or a block diagram of mathematical operators. The use of objects minimizes the representational gap between the model and actual process. From the users point of view, construction of a simulation model becomes equivalent to drawing a plant schematic. As an example application, a package developed for the simulation of nuclear power plants is described. The package allows users to build simulation models by selecting iconic representations of plant components from a menu and connecting them with a mouse. Objects for generating a mathematical model of the system and for controlling the simulation are automatically generated, freeing the user to concentrate on describing his process. This example illustrates the use of object-oriented programming to create a highly interactive and automated simulation environment. 2 figs

Translation of PLC Programs to x86 for Simulation and Verification

CERN Document Server

Sallai, Gyula

2017-01-01

PLC programs are written in special languages, variants of the languages defined in the IEC 61131 standard. These programs cannot be directly executed on personal computers (on x86 architecture). To perform simulation of the PLC program or diagnostics during development, either a real PLC or a PLC simulator has to be used. However, these solutions are often inflexible and they do not provide appropriate performance. By generating x86-representations (semantically equivalent programs which can be executed on PCs, e.g. written in C, C++ or Java) of the PLC programs, some of these challenges could be met. PLCverif is a PLC program verification tool developed at CERN which includes a parser for Siemens PLC programs. In this work, we describe a code generator based on this parser of PLCverif. This work explores the possibilities and challenges of generating programs in widely-used general purpose languages from PLC programs, and provides a proof-of-concept code generation implementation. The presented solution dem...

Developments in the electron gun simulation program, EGUN

International Nuclear Information System (INIS)

Herrmannsfeldt, W.B.

1995-01-01

This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described. copyright 1995 American Institute of Physics

Atributos mecânicos e erosão por salpicamento em amostras de latossolo vermelho-amarelo sob efeito de vinhaça Soil mechanical attributes and splash erosion on samples of red-yellow latosol influenced by sugarcane vinasse

Directory of Open Access Journals (Sweden)

Luiz Gustavo Fernandes Julião

2011-02-01

was obtained from an artisanal sugarcane brandy alembic. Undisturbed and disturbed soil samples were collected at 0 to 3 cm and 60 to 63 cm depths. Disturbed soil samples were used for soil characterization, determination of consistence limits and Normal Proctor essay after material incubation with plonk. Undisturbed soil samples were saturated with plonk or distilled water (control during 48 hours for testing the compressibility and resistance to splash by using simulated rainfall. The plonk altered the consistence limits of studied layers. For the 0-3 cm layer, the plonk reduced the friable range, and for the 60-63 cm layer the effect was in the opposite direction. For both layers, the plonk increased Dmax and decreased Uoptimum. Regardless of the plonk treatment, both layers presented the same load support capacity. The compaction degree of samples influenced the splash erosion. The increase of the applied pressure over the samples resulted in increase of splash material quantity. At the 60-63 cm layer, the plonk treatment reduced the splash material quantity by increasing the applied pressure, mainly when the samples were at field capacity.

Knowledge-based simulation using object-oriented programming

Science.gov (United States)

Sidoran, Karen M.

1993-01-01

Simulations have become a powerful mechanism for understanding and modeling complex phenomena. Their results have had substantial impact on a broad range of decisions in the military, government, and industry. Because of this, new techniques are continually being explored and developed to make them even more useful, understandable, extendable, and efficient. One such area of research is the application of the knowledge-based methods of artificial intelligence (AI) to the computer simulation field. The goal of knowledge-based simulation is to facilitate building simulations of greatly increased power and comprehensibility by making use of deeper knowledge about the behavior of the simulated world. One technique for representing and manipulating knowledge that has been enhanced by the AI community is object-oriented programming. Using this technique, the entities of a discrete-event simulation can be viewed as objects in an object-oriented formulation. Knowledge can be factual (i.e., attributes of an entity) or behavioral (i.e., how the entity is to behave in certain circumstances). Rome Laboratory's Advanced Simulation Environment (RASE) was developed as a research vehicle to provide an enhanced simulation development environment for building more intelligent, interactive, flexible, and realistic simulations. This capability will support current and future battle management research and provide a test of the object-oriented paradigm for use in large scale military applications.

PATH: a lumped-element beam-transport simulation program with space charge

International Nuclear Information System (INIS)

Farrell, J.A.

1983-01-01

PATH is a group of computer programs for simulating charged-particle beam-transport systems. It was developed for evaluating the effects of some aberrations without a time-consuming integration of trajectories through the system. The beam-transport portion of PATH is derived from the well-known program, DECAY TURTLE. PATH contains all features available in DECAY TURTLE (including the input format) plus additional features such as a more flexible random-ray generator, longitudinal phase space, some additional beamline elements, and space-charge routines. One of the programs also provides a simulation of an Alvarez linear accelerator. The programs, originally written for a CDC 7600 computer system, also are available on a VAX-VMS system. All of the programs are interactive with input prompting for ease of use

Tecnomatix Plant Simulation modeling and programming by means of examples

CERN Document Server

Bangsow, Steffen

2015-01-01

This book systematically introduces the development of simulation models as well as the implementation and evaluation of simulation experiments with Tecnomatix Plant Simulation. It deals with all users of Plant Simulation, who have more complex tasks to handle. It also looks for an easy entry into the program. Particular attention has been paid to introduce the simulation flow language SimTalk and its use in various areas of the simulation. The author demonstrates with over 200 examples how to combine the blocks for simulation models and how to deal with SimTalk for complex control and analys

ADAM: A computer program to simulate selective-breeding schemes for animals

DEFF Research Database (Denmark)

Pedersen, L D; Sørensen, A C; Henryon, M

2009-01-01

ADAM is a computer program that models selective breeding schemes for animals using stochastic simulation. The program simulates a population of animals and traces the genetic changes in the population under different selective breeding scenarios. It caters to different population structures......, genetic models, selection strategies, and mating designs. ADAM can be used to evaluate breeding schemes and generate genetic data to test statistical tools...

Validation studies of the DOE-2 Building Energy Simulation Program. Final Report

Energy Technology Data Exchange (ETDEWEB)

Sullivan, R.; Winkelmann, F.

1998-06-01

This report documents many of the validation studies (Table 1) of the DOE-2 building energy analysis simulation program that have taken place since 1981. Results for several versions of the program are presented with the most recent study conducted in 1996 on version DOE-2.1E and the most distant study conducted in 1981 on version DOE-1.3. This work is part of an effort related to continued development of DOE-2, particularly in its use as a simulation engine for new specialized versions of the program such as the recently released RESFEN 3.1. RESFEN 3.1 is a program specifically dealing with analyzing the energy performance of windows in residential buildings. The intent in providing the results of these validation studies is to give potential users of the program a high degree of confidence in the calculated results. Validation studies in which calculated simulation data is compared to measured data have been conducted throughout the development of the DOE-2 program. Discrepancies discovered during the course of such work has resulted in improvements in the simulation algorithms. Table 2 provides a listing of additions and modifications that have been made to various versions of the program since version DOE-2.1A. One of the most significant recent changes in the program occurred with version DOE-2.1E. An improved algorithm for calculating the outside surface film coefficient was implemented. In addition, integration of the WINDOW 4 program was accomplished resulting in improved ability in analyzing window energy performance. Validation and verification of a program as sophisticated as DOE-2 must necessarily be limited because of the approximations inherent in the program. For example, the most accurate model of the heat transfer processes in a building would include a three-dimensional analysis. To justify such detailed algorithmic procedures would correspondingly require detailed information describing the building and/or HVAC system and energy plant parameters

Trace contaminant control simulation computer program, version 8.1

Science.gov (United States)

Perry, J. L.

1994-01-01

The Trace Contaminant Control Simulation computer program is a tool for assessing the performance of various process technologies for removing trace chemical contamination from a spacecraft cabin atmosphere. Included in the simulation are chemical and physical adsorption by activated charcoal, chemical adsorption by lithium hydroxide, absorption by humidity condensate, and low- and high-temperature catalytic oxidation. Means are provided for simulating regenerable as well as nonregenerable systems. The program provides an overall mass balance of chemical contaminants in a spacecraft cabin given specified generation rates. Removal rates are based on device flow rates specified by the user and calculated removal efficiencies based on cabin concentration and removal technology experimental data. Versions 1.0 through 8.0 are documented in NASA TM-108409. TM-108409 also contains a source file listing for version 8.0. Changes to version 8.0 are documented in this technical memorandum and a source file listing for the modified version, version 8.1, is provided. Detailed descriptions for the computer program subprograms are extracted from TM-108409 and modified as necessary to reflect version 8.1. Version 8.1 supersedes version 8.0. Information on a separate user's guide is available from the author.

specsim: A Fortran-77 program for conditional spectral simulation in 3D

Science.gov (United States)

Yao, Tingting

1998-12-01

A Fortran 77 program, specsim, is presented for conditional spectral simulation in 3D domains. The traditional Fourier integral method allows generating random fields with a given covariance spectrum. Conditioning to local data is achieved by an iterative identification of the conditional phase information. A flowchart of the program is given to illustrate the implementation procedures of the program. A 3D case study is presented to demonstrate application of the program. A comparison with the traditional sequential Gaussian simulation algorithm emphasizes the advantages and drawbacks of the proposed algorithm.

Feasibility of High-Resolution Soil Erosion Measurements by Means of Rainfall Simulations and SfM Photogrammetry

Directory of Open Access Journals (Sweden)

Phoebe Hänsel

2016-11-01

Full Text Available The silty soils of the intensively used agricultural landscape of the Saxon loess province, eastern Germany, are very prone to soil erosion, mainly caused by water erosion. Rainfall simulations, and also increasingly structure-from-motion (SfM photogrammetry, are used as methods in soil erosion research not only to assess soil erosion by water, but also to quantify soil loss. This study aims to validate SfM photogrammetry determined soil loss estimations with rainfall simulations measurements. Rainfall simulations were performed at three agricultural sites in central Saxony. Besides the measured data runoff and soil loss by sampling (in mm, terrestrial images were taken from the plots with digital cameras before and after the rainfall simulation. Subsequently, SfM photogrammetry was used to reconstruct soil surface changes due to soil erosion in terms of high resolution digital elevation models (DEMs for the pre- and post-event (resolution 1 × 1 mm. By multi-temporal change detection, the digital elevation model of difference (DoD and an averaged soil loss (in mm is received, which was compared to the soil loss by sampling. Soil loss by DoD was higher than soil loss by sampling. The method of SfM photogrammetry-determined soil loss estimations also include a comparison of three different ground control point (GCP approaches, revealing that the most complex one delivers the most reliable soil loss by DoD. Additionally, soil bulk density changes and splash erosion beyond the plot were measured during the rainfall simulation experiments in order to separate these processes and associated surface changes from the soil loss by DoD. Furthermore, splash was negligibly small, whereas higher soil densities after the rainfall simulations indicated soil compaction. By means of calculated soil surface changes due to soil compaction, the soil loss by DoD achieved approximately the same value as the soil loss by rainfall simulation.

A simulation-based training program improves emergency department staff communication.

Science.gov (United States)

Sweeney, Lynn A; Warren, Otis; Gardner, Liz; Rojek, Adam; Lindquist, David G

2014-01-01

The objectives of this study were to evaluate the effectiveness of Project CLEAR!, a novel simulation-based training program designed to instill Crew Resource Management (CRM) as the communication standard and to create a service-focused environment in the emergency department (ED) by standardizing the patient encounter. A survey-based study compared physicians' and nurses' perceptions of the quality of communication before and after the training program. Surveys were developed to measure ED staff perceptions of the quality of communication between staff members and with patients. Pretraining and posttraining survey results were compared. After the training program, survey scores improved significantly on questions that asked participants to rate the overall communication between staff members and between staff and patients. A simulation-based training program focusing on CRM and standardizing the patient encounter improves communication in the ED, both between staff members and between staff members and patients.

SNOW: a digital computer program for the simulation of ion beam devices

International Nuclear Information System (INIS)

Boers, J.E.

1980-08-01

A digital computer program, SNOW, has been developed for the simulation of dense ion beams. The program simulates the plasma expansion cup (but not the plasma source itself), the acceleration region, and a drift space with neutralization if desired. The ion beam is simulated by computing representative trajectories through the device. The potentials are simulated on a large rectangular matrix array which is solved by iterative techniques. Poisson's equation is solved at each point within the configuration using space-charge densities computed from the ion trajectories combined with background electron and/or ion distributions. The simulation methods are described in some detail along with examples of both axially-symmetric and rectangular beams. A detailed description of the input data is presented

Material control system simulator program reference manual

Energy Technology Data Exchange (ETDEWEB)

Hollstien, R.B.

1978-01-24

A description is presented of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts. Although MCSS may be used independently in the design or analysis of material handling and processing systems, it has been tailored toward the determination of material accountability and the response of material control systems to adversary action sequences.

Material control system simulator program reference manual

International Nuclear Information System (INIS)

Hollstien, R.B.

1978-01-01

A description is presented of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts. Although MCSS may be used independently in the design or analysis of material handling and processing systems, it has been tailored toward the determination of material accountability and the response of material control systems to adversary action sequences

Water Hammer Simulations of MMH Propellant - New Capability Demonstration of the Generalized Fluid Flow Simulation Program

Science.gov (United States)

Burkhardt, Z.; Ramachandran, N.; Majumdar, A.

2017-01-01

Fluid Transient analysis is important for the design of spacecraft propulsion system to ensure structural stability of the system in the event of sudden closing or opening of the valve. Generalized Fluid System Simulation Program (GFSSP), a general purpose flow network code developed at NASA/MSFC is capable of simulating pressure surge due to sudden opening or closing of valve when thermodynamic properties of real fluid are available for the entire range of simulation. Specifically GFSSP needs an accurate representation of pressure-density relationship in order to predict pressure surge during a fluid transient. Unfortunately, the available thermodynamic property programs such as REFPROP, GASP or GASPAK does not provide the thermodynamic properties of Monomethylhydrazine (MMH). This paper will illustrate the process used for building a customized table of properties of state variables from available properties and speed of sound that is required by GFSSP for simulation. Good agreement was found between the simulations and measured data. This method can be adopted for modeling flow networks and systems with other fluids whose properties are not known in detail in order to obtain general technical insight. Rigorous code validation of this approach will be done and reported at a future date.

14 CFR 121.407 - Training program: Approval of airplane simulators and other training devices.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Training program: Approval of airplane... Program § 121.407 Training program: Approval of airplane simulators and other training devices. (a) Each airplane simulator and other training device that is used in a training course permitted under § 121.409...

Using Discrete Event Simulation for Programming Model Exploration at Extreme-Scale: Macroscale Components for the Structural Simulation Toolkit (SST).

Energy Technology Data Exchange (ETDEWEB)

Wilke, Jeremiah J [Sandia National Laboratories (SNL-CA), Livermore, CA (United States); Kenny, Joseph P. [Sandia National Laboratories (SNL-CA), Livermore, CA (United States)

2015-02-01

Discrete event simulation provides a powerful mechanism for designing and testing new extreme- scale programming models for high-performance computing. Rather than debug, run, and wait for results on an actual system, design can first iterate through a simulator. This is particularly useful when test beds cannot be used, i.e. to explore hardware or scales that do not yet exist or are inaccessible. Here we detail the macroscale components of the structural simulation toolkit (SST). Instead of depending on trace replay or state machines, the simulator is architected to execute real code on real software stacks. Our particular user-space threading framework allows massive scales to be simulated even on small clusters. The link between the discrete event core and the threading framework allows interesting performance metrics like call graphs to be collected from a simulated run. Performance analysis via simulation can thus become an important phase in extreme-scale programming model and runtime system design via the SST macroscale components.

Building interactive simulations in a Web page design program.

Science.gov (United States)

Kootsey, J Mailen; Siriphongs, Daniel; McAuley, Grant

2004-01-01

A new Web software architecture, NumberLinX (NLX), has been integrated into a commercial Web design program to produce a drag-and-drop environment for building interactive simulations. NLX is a library of reusable objects written in Java, including input, output, calculation, and control objects. The NLX objects were added to the palette of available objects in the Web design program to be selected and dropped on a page. Inserting an object in a Web page is accomplished by adding a template block of HTML code to the page file. HTML parameters in the block must be set to user-supplied values, so the HTML code is generated dynamically, based on user entries in a popup form. Implementing the object inspector for each object permits the user to edit object attributes in a form window. Except for model definition, the combination of the NLX architecture and the Web design program permits construction of interactive simulation pages without writing or inspecting code.

Simulation model for wind energy storage systems. Volume III. Program descriptions. [SIMWEST CODE

Energy Technology Data Exchange (ETDEWEB)

Warren, A.W.; Edsinger, R.W.; Burroughs, J.D.

1977-08-01

The effort developed a comprehensive computer program for the modeling of wind energy/storage systems utilizing any combination of five types of storage (pumped hydro, battery, thermal, flywheel and pneumatic). An acronym for the program is SIMWEST (Simulation Model for Wind Energy Storage). The level of detail of SIMWEST is consistent with a role of evaluating the economic feasibility as well as the general performance of wind energy systems. The software package consists of two basic programs and a library of system, environmental, and load components. Volume III, the SIMWEST program description contains program descriptions, flow charts and program listings for the SIMWEST Model Generation Program, the Simulation program, the File Maintenance program and the Printer Plotter program. Volume III generally would not be required by SIMWEST user.

Establishing High-Quality Prostate Brachytherapy Using a Phantom Simulator Training Program

Energy Technology Data Exchange (ETDEWEB)

Thaker, Nikhil G. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Kudchadker, Rajat J. [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Swanson, David A. [Department of Urology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Albert, Jeffrey M. [Department of Radiation Oncology, Banner Health, Loveland/Greeley, Colorado (United States); Mahmood, Usama; Pugh, Thomas J.; Boehling, Nicholas S. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Bruno, Teresa L. [Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Prestidge, Bradley R. [Department of Radiation Oncology, Bon Secours Health System, Norfolk, Virginia (United States); Crook, Juanita M. [Department of Radiation Oncology, Cancer Center for the Southern Interior, Kelowna, British Columbia (Canada); Cox, Brett W.; Potters, Louis [Department of Radiation Medicine, North Shore-LIJ Health System, New Hyde Park, New York (United States); Moran, Brian J. [Chicago Prostate Center, Westmont, Illinois (United States); Keyes, Mira [Department of Radiation Oncology, British Columbia Cancer Agency, Vancouver Center, Vancouver, British Columbia (Canada); Kuban, Deborah A. [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Frank, Steven J., E-mail: sjfrank@mdanderson.org [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States)

2014-11-01

Purpose: To design and implement a unique training program that uses a phantom-based simulator to teach the process of prostate brachytherapy (PB) quality assurance and improve the quality of education. Methods and Materials: Trainees in our simulator program were practicing radiation oncologists, radiation oncology residents, and fellows of the American Brachytherapy Society. The program emphasized 6 core areas of quality assurance: patient selection, simulation, treatment planning, implant technique, treatment evaluation, and outcome assessment. Using the Iodine 125 ({sup 125}I) preoperative treatment planning technique, trainees implanted their ultrasound phantoms with dummy seeds (ie, seeds with no activity). Pre- and postimplant dosimetric parameters were compared and correlated using regression analysis. Results: Thirty-one trainees successfully completed the simulator program during the period under study. The mean phantom prostate size, number of seeds used, and total activity were generally consistent between trainees. All trainees met the V100 >95% objective both before and after implantation. Regardless of the initial volume of the prostate phantom, trainees' ability to cover the target volume with at least 100% of the dose (V100) was not compromised (R=0.99 pre- and postimplant). However, the V150 had lower concordance (R=0.37) and may better reflect heterogeneity control of the implant process. Conclusions: Analysis of implants from this phantom-based simulator shows a high degree of consistency between trainees and uniformly high-quality implants with respect to parameters used in clinical practice. This training program provides a valuable educational opportunity that improves the quality of PB training and likely accelerates the learning curve inherent in PB. Prostate phantom implantation can be a valuable first step in the acquisition of the required skills to safely perform PB.

Establishing High-Quality Prostate Brachytherapy Using a Phantom Simulator Training Program

International Nuclear Information System (INIS)

Thaker, Nikhil G.; Kudchadker, Rajat J.; Swanson, David A.; Albert, Jeffrey M.; Mahmood, Usama; Pugh, Thomas J.; Boehling, Nicholas S.; Bruno, Teresa L.; Prestidge, Bradley R.; Crook, Juanita M.; Cox, Brett W.; Potters, Louis; Moran, Brian J.; Keyes, Mira; Kuban, Deborah A.; Frank, Steven J.

2014-01-01

Purpose: To design and implement a unique training program that uses a phantom-based simulator to teach the process of prostate brachytherapy (PB) quality assurance and improve the quality of education. Methods and Materials: Trainees in our simulator program were practicing radiation oncologists, radiation oncology residents, and fellows of the American Brachytherapy Society. The program emphasized 6 core areas of quality assurance: patient selection, simulation, treatment planning, implant technique, treatment evaluation, and outcome assessment. Using the Iodine 125 ( 125 I) preoperative treatment planning technique, trainees implanted their ultrasound phantoms with dummy seeds (ie, seeds with no activity). Pre- and postimplant dosimetric parameters were compared and correlated using regression analysis. Results: Thirty-one trainees successfully completed the simulator program during the period under study. The mean phantom prostate size, number of seeds used, and total activity were generally consistent between trainees. All trainees met the V100 >95% objective both before and after implantation. Regardless of the initial volume of the prostate phantom, trainees' ability to cover the target volume with at least 100% of the dose (V100) was not compromised (R=0.99 pre- and postimplant). However, the V150 had lower concordance (R=0.37) and may better reflect heterogeneity control of the implant process. Conclusions: Analysis of implants from this phantom-based simulator shows a high degree of consistency between trainees and uniformly high-quality implants with respect to parameters used in clinical practice. This training program provides a valuable educational opportunity that improves the quality of PB training and likely accelerates the learning curve inherent in PB. Prostate phantom implantation can be a valuable first step in the acquisition of the required skills to safely perform PB

Updating of the program for simulation of Darlington shutdown and regulation systems

International Nuclear Information System (INIS)

1988-07-01

This report describes the current status of the developments of a simulation of the Darlington Nuclear Generating Station shutdown and regulating systems, DARSIM done under contract to the Atomic Energy Control Board (AECB). The DARSIM program simulates the spatial neutron dynamics, the regulation of the reactor power, and shutdown system 1 and shutdown system 2 software. The DARSIM program operates in the interactive simulation program environment. DARSIM was installed on the APOLLO computer at the AECB and a version for an IBM-PC was also provided for the exclusive use of the AECB. Shutdown system software was updated to incorporate the latest revisions in the functional specifications. Additional developments have been provided to assist in the use and interpretation of the DARSIM results

Robot off-line programming and simulation as a true CIME-subsystem

DEFF Research Database (Denmark)

Nielsen, L.F; Trostmann, S; Trostmann, Erik

1992-01-01

A robot off-line programming and real-time simulation system, ROPSIM, which is based on the neutral interface concept and features simulation of the dynamics of both the controller and robot arm, has been developed. To avoid dependency on dedicated robot models, ROPSIM is based on generic models...... describing the robot controller, robot arm geometry, and the robot and arm kinetics. The software was developed using the C++ programming language. The key modules are discussed. The system is a true computer-integrated manufacturing and engineering subsystem which facilitates the exchange and reuse of robot...... model definition data and robot program definition data with systems of other origin or different functionality...

Video Monitoring a Simulation-Based Quality Improvement Program in Bihar, India.

Science.gov (United States)

Dyer, Jessica; Spindler, Hilary; Christmas, Amelia; Shah, Malay Bharat; Morgan, Melissa; Cohen, Susanna R; Sterne, Jason; Mahapatra, Tanmay; Walker, Dilys

2018-04-01

Simulation-based training has become an accepted clinical training andragogy in high-resource settings with its use increasing in low-resource settings. Video recordings of simulated scenarios are commonly used by facilitators. Beyond using the videos during debrief sessions, researchers can also analyze the simulation videos to quantify technical and nontechnical skills during simulated scenarios over time. Little is known about the feasibility and use of large-scale systems to video record and analyze simulation and debriefing data for monitoring and evaluation in low-resource settings. This manuscript describes the process of designing and implementing a large-scale video monitoring system. Mentees and Mentors were consented and all simulations and debriefs conducted at 320 Primary Health Centers (PHCs) were video recorded. The system design, number of video recordings, and inter-rater reliability of the coded videos were assessed. The final dataset included a total of 11,278 videos. Overall, a total of 2,124 simulation videos were coded and 183 (12%) were blindly double-coded. For the double-coded sample, the average inter-rater reliability (IRR) scores were 80% for nontechnical skills, and 94% for clinical technical skills. Among 4,450 long debrief videos received, 216 were selected for coding and all were double-coded. Data quality of simulation videos was found to be very good in terms of recorded instances of "unable to see" and "unable to hear" in Phases 1 and 2. This study demonstrates that video monitoring systems can be effectively implemented at scale in resource limited settings. Further, video monitoring systems can play several vital roles within program implementation, including monitoring and evaluation, provision of actionable feedback to program implementers, and assurance of program fidelity.

Simulation of micromegas detector by Garfield program

International Nuclear Information System (INIS)

Zhang Xiaodong; Zhang Yi; Yang Herun; Xu Hushan; Duan Limin; Li Chunyan; Li Zuyu

2007-01-01

In this paper, a batch file which describes the detailed structure and the corresponding physical process of Micro-Mesh Gaseous Structure (Micromegas) detector, the macro commands and the control structures based on the Garfield program has been developed. And using the Garfield program controlled by this batch file, the detector's gain and spatial resolution have been investigated under different conditions. These results obtained by the simulation program not only exhibit the influences of the mesh and drift voltage, the mixture gas proportion, the distance between the mesh cathode and the printed circuit board readout anode, and the Lines Per Inch of the mesh cathode on the gain and spatial resolution of the detector, but also are very important to optimize the design, shorten the experimental period, and save cost during the detector development. Additionally, they also indicate that the Garfield program is a powerful tool for the Micromegas detector design and optimization. (authors)

Computer simulation program for medium-energy ion scattering and Rutherford backscattering spectrometry

Science.gov (United States)

Nishimura, Tomoaki

2016-03-01

A computer simulation program for ion scattering and its graphical user interface (MEISwin) has been developed. Using this program, researchers have analyzed medium-energy ion scattering and Rutherford backscattering spectrometry at Ritsumeikan University since 1998, and at Rutgers University since 2007. The main features of the program are as follows: (1) stopping power can be chosen from five datasets spanning several decades (from 1977 to 2011), (2) straggling can be chosen from two datasets, (3) spectral shape can be selected as Gaussian or exponentially modified Gaussian, (4) scattering cross sections can be selected as Coulomb or screened, (5) simulations adopt the resonant elastic scattering cross section of 16O(4He, 4He)16O, (6) pileup simulation for RBS spectra is supported, (7) natural and specific isotope abundances are supported, and (8) the charge fraction can be chosen from three patterns (fixed, energy-dependent, and ion fraction with charge-exchange parameters for medium-energy ion scattering). This study demonstrates and discusses the simulations and their results.

Evaluation of the BEAM--BEAM effect in PEP using Myer's simulation program

International Nuclear Information System (INIS)

Hutton, A.

1982-09-01

The program BEAM BEAM written by Steve Myers for the LEP machine at CERN has given encouraging results in the simulation of the beam-beam effect in electron-positron storage rings. It therefore seemed worthwhile to apply the program to PEP with two main intentions. Firstly, to confirm the validity of the program by comparison with experimental data from previous PEP runs and secondly, to search for an improvement in the operating conditions of PEP. Clearly a successful prediction would also enhance the credibility of the program. The program itself has been extensively described in the literature and will not be repeated here, except for some comments of direct relevance to the present simulation. 14 refs., 15 figs., 4 tabs

A mass-conserving multiphase lattice Boltzmann model for simulation of multiphase flows

Science.gov (United States)

Niu, Xiao-Dong; Li, You; Ma, Yi-Ren; Chen, Mu-Feng; Li, Xiang; Li, Qiao-Zhong

2018-01-01

In this study, a mass-conserving multiphase lattice Boltzmann (LB) model is proposed for simulating the multiphase flows. The proposed model developed in the present study is to improve the model of Shao et al. ["Free-energy-based lattice Boltzmann model for simulation of multiphase flows with density contrast," Phys. Rev. E 89, 033309 (2014)] by introducing a mass correction term in the lattice Boltzmann model for the interface. The model of Shao et al. [(the improved Zheng-Shu-Chew (Z-S-C model)] correctly considers the effect of the local density variation in momentum equation and has an obvious improvement over the Zheng-Shu-Chew (Z-S-C) model ["A lattice Boltzmann model for multiphase flows with large density ratio," J. Comput. Phys. 218(1), 353-371 (2006)] in terms of solution accuracy. However, due to the physical diffusion and numerical dissipation, the total mass of each fluid phase cannot be conserved correctly. To solve this problem, a mass correction term, which is similar to the one proposed by Wang et al. ["A mass-conserved diffuse interface method and its application for incompressible multiphase flows with large density ratio," J. Comput. Phys. 290, 336-351 (2015)], is introduced into the lattice Boltzmann equation for the interface to compensate the mass losses or offset the mass increase. Meanwhile, to implement the wetting boundary condition and the contact angle, a geometric formulation and a local force are incorporated into the present mass-conserving LB model. The proposed model is validated by verifying the Laplace law, simulating both one and two aligned droplets splashing onto a liquid film, droplets standing on an ideal wall, droplets with different wettability splashing onto smooth wax, and bubbles rising under buoyancy. Numerical results show that the proposed model can correctly simulate multiphase flows. It was found that the mass is well-conserved in all cases considered by the model developed in the present study. The developed

tmLQCD: a program suite to simulate Wilson twisted mass lattice QCD

Energy Technology Data Exchange (ETDEWEB)

Jansen, Karl [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Urbach, Carsten [Institut fuer Physik, Humboldt-Universitaet, Berlin (Germany)

2009-05-15

We discuss a program suite for simulating Quantum Chromodynamics on a 4-dimensional space-time lattice. The basic Hybrid Monte Carlo algorithm is introduced and a number of algorithmic improvements are explained. We then discuss the implementations of these concepts as well as our parallelisation strategy in the actual simulation code. Finally, we provide a user guide to compile and run the program. (orig.)

tmLQCD: a program suite to simulate Wilson twisted mass lattice QCD

International Nuclear Information System (INIS)

Jansen, Karl; Urbach, Carsten

2009-05-01

We discuss a program suite for simulating Quantum Chromodynamics on a 4-dimensional space-time lattice. The basic Hybrid Monte Carlo algorithm is introduced and a number of algorithmic improvements are explained. We then discuss the implementations of these concepts as well as our parallelisation strategy in the actual simulation code. Finally, we provide a user guide to compile and run the program. (orig.)

Usage of I++ Simulator to Program Coordinate Measuring Machines when Common Programming Methods are difficult to apply

Directory of Open Access Journals (Sweden)

Gąska A.

2014-02-01

Full Text Available Nowadays, simulators facilitate tasks performed daily by the engineers of different branches, including coordinate metrologists. Sometimes it is difficult or almost impossible to program a Coordinate Measuring Machine (CMM using standard methods. This happens, for example, during measurements of nano elements or in cases when measurements are performed on high-precision (accurate measuring machines which work in strictly air-conditioned spaces and the presence of the operator in such room during the programming of CMM could cause an increase in temperature, which in turn could make it necessary to wait some time until conditions stabilize. This article describes functioning of a simulator and its usage during Coordinate Measuring Machine programming in the latter situation. Article also describes a general process of programming CMMs which ensures the correct machine performance after starting the program on a real machine. As an example proving the presented considerations, measurement of exemplary workpiece, which was performed on the machine working in the strictly air-conditioned room, was described

A Study on Evaluation of Training Program for MCR Operators of SMART Simulator

Energy Technology Data Exchange (ETDEWEB)

Park, Hyun Jun; Lee, Joon Ku; Jeong, Kwang Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

It is important to develop a training program by simulators in main control room of nuclear power plants because there is no an operation expert and no operating experience in the pre-construction phase of nuclear power plants. It is also necessary to develop a training program and its evaluation method taking human error into account. The purpose of this study is developing evaluation model of simulators. In a training program, once training requirements are selected, evaluation of training is as important as its implementation. Training effectiveness is available value in a simulator-based environment. The main control room of SMART (System-integrated Modular Advanced ReacTor) is consist of workstation, visual display units such as LDP and FPD based on digital systems. Cognitive behaviors of a high level are required to operators in these man-machine interface system (MMIS). Therefore, it is essential to identify training requirements and to develop its evaluation model. Virtual Environments such as a simulator have utilized by a lot of industries and companies for training and accident prevention. Simulators have three primary benefits. The first is that training by simulators is less expensive than those in real environment. The second is that simulators enable safety enhancement using systematic training program. The third is that simulators provide a preliminary to prevent human error. It is significant to apply TER, TCR, TCE in evaluation of training effect. It is expected that these could be applied to revise training criteria and enable to consider efficiency in terms of cost and benefit.

A Study on Evaluation of Training Program for MCR Operators of SMART Simulator

International Nuclear Information System (INIS)

Park, Hyun Jun; Lee, Joon Ku; Jeong, Kwang Il

2015-01-01

It is important to develop a training program by simulators in main control room of nuclear power plants because there is no an operation expert and no operating experience in the pre-construction phase of nuclear power plants. It is also necessary to develop a training program and its evaluation method taking human error into account. The purpose of this study is developing evaluation model of simulators. In a training program, once training requirements are selected, evaluation of training is as important as its implementation. Training effectiveness is available value in a simulator-based environment. The main control room of SMART (System-integrated Modular Advanced ReacTor) is consist of workstation, visual display units such as LDP and FPD based on digital systems. Cognitive behaviors of a high level are required to operators in these man-machine interface system (MMIS). Therefore, it is essential to identify training requirements and to develop its evaluation model. Virtual Environments such as a simulator have utilized by a lot of industries and companies for training and accident prevention. Simulators have three primary benefits. The first is that training by simulators is less expensive than those in real environment. The second is that simulators enable safety enhancement using systematic training program. The third is that simulators provide a preliminary to prevent human error. It is significant to apply TER, TCR, TCE in evaluation of training effect. It is expected that these could be applied to revise training criteria and enable to consider efficiency in terms of cost and benefit

PGOPHER: A program for simulating rotational, vibrational and electronic spectra

Science.gov (United States)

Western, Colin M.

2017-01-01

The PGOPHER program is a general purpose program for simulating and fitting molecular spectra, particularly the rotational structure. The current version can handle linear molecules, symmetric tops and asymmetric tops and many possible transitions, both allowed and forbidden, including multiphoton and Raman spectra in addition to the common electric dipole absorptions. Many different interactions can be included in the calculation, including those arising from electron and nuclear spin, and external electric and magnetic fields. Multiple states and interactions between them can also be accounted for, limited only by available memory. Fitting of experimental data can be to line positions (in many common formats), intensities or band contours and the parameters determined can be level populations as well as rotational constants. PGOPHER is provided with a powerful and flexible graphical user interface to simplify many of the tasks required in simulating, understanding and fitting molecular spectra, including Fortrat diagrams and energy level plots in addition to overlaying experimental and simulated spectra. The program is open source, and can be compiled with open source tools. This paper provides a formal description of the operation of version 9.1.

Test results of the new NSSS thermal-hydraulics program of the KNPEC-2 simulator

International Nuclear Information System (INIS)

Jeong, J. Z.; Kim, K. D.; Lee, M. S.; Hong, J. H.; Lee, Y. K.; Seo, J. S.; Kweon, K. J.; Lee, S. W.

2001-01-01

As a part of the KNPEC-2 Simulator Upgrade Project, KEPRI and KAERI have developed a new NSSS thermal-hydraulics program, which is based on the best-estimate system code, RETRAN. The RETRAN code was originally developed for realistic simulation of thermal-hydraulic transient in power plant systems. The capability of 'real-time simulation' and robustness' should be first developed before being implemented in full-scope simulators. For this purpose, we have modified the RETRAN code by (i) eliminating the correlations' discontinuities between flow regime maps, (ii) simplifying physical correlations, (iii) correcting errors in the original program, and (iv) others. This paper briefly presents the test results fo the new NSSS thermal-hydraulics program

Investigation of roughing machining simulation by using visual basic programming in NX CAM system

Science.gov (United States)

Hafiz Mohamad, Mohamad; Nafis Osman Zahid, Muhammed

2018-03-01

This paper outlines a simulation study to investigate the characteristic of roughing machining simulation in 4th axis milling processes by utilizing visual basic programming in NX CAM systems. The selection and optimization of cutting orientation in rough milling operation is critical in 4th axis machining. The main purpose of roughing operation is to approximately shape the machined parts into finished form by removing the bulk of material from workpieces. In this paper, the simulations are executed by manipulating a set of different cutting orientation to generate estimated volume removed from the machine parts. The cutting orientation with high volume removal is denoted as an optimum value and chosen to execute a roughing operation. In order to run the simulation, customized software is developed to assist the routines. Operations build-up instructions in NX CAM interface are translated into programming codes via advanced tool available in the Visual Basic Studio. The codes is customized and equipped with decision making tools to run and control the simulations. It permits the integration with any independent program files to execute specific operations. This paper aims to discuss about the simulation program and identifies optimum cutting orientations for roughing processes. The output of this study will broaden up the simulation routines performed in NX CAM systems.

Evaluating simulant materials for understanding cranial backspatter from a ballistic projectile.

Science.gov (United States)

Das, Raj; Collins, Alistair; Verma, Anurag; Fernandez, Justin; Taylor, Michael

2015-05-01

In cranial wounds resulting from a gunshot, the study of backspatter patterns can provide information about the actual incidents by linking material to surrounding objects. This study investigates the physics of backspatter from a high-speed projectile impact and evaluates a range of simulant materials using impact tests. Next, we evaluate a mesh-free method called smoothed particle hydrodynamics (SPH) to model the splashing mechanism during backspatter. The study has shown that a projectile impact causes fragmentation at the impact site, while transferring momentum to fragmented particles. The particles travel along the path of least resistance, leading to partial material movement in the reverse direction of the projectile motion causing backspatter. Medium-density fiberboard is a better simulant for a human skull than polycarbonate, and lorica leather is a better simulant for a human skin than natural rubber. SPH is an effective numerical method for modeling the high-speed impact fracture and fragmentations. © 2015 American Academy of Forensic Sciences.

PATHWAY: a simulation model of radionuclide-transport through agricultural food chains

International Nuclear Information System (INIS)

Kirchner, T.B.; Whicker, F.W.; Otis, M.D.

1982-01-01

PATHWAY simulates the transport of radionuclides from fallout through an agricultural ecosystem. The agro-ecosystem is subdivided into several land management units, each of which is used either for grazing animals, for growing hay, or for growing food crops. The model simulates the transport of radionuclides by both discrete events and continuous, time-dependent processes. The discrete events include tillage of soil, harvest and storage of crops,and deposition of fallout. The continuous processes include the transport of radionuclides due to resuspension, weathering, rain splash, percolation, leaching, adsorption and desorption of radionuclides in the soil, root uptake, foliar absorption, growth and senescence of vegetation, and the ingestion assimilation, and excretion of radionuclides by animals. Preliminary validation studies indicate that the model dynamics and simulated values of radionuclide concentrations in several agricultural products agree well with measured values when the model is driven with site specific data on deposition from world-wide fallout

Faculty Development for Simulation Programs: Five Issues for the Future of Debriefing Training

DEFF Research Database (Denmark)

Cheng, Adan; Grant, Vincent; Dieckmann, Peter

2015-01-01

STATEMENT: Debriefing is widely recognized as a critically important element of simulation-based education. Simulation educators obtain and/or seek debriefing training from various sources, including workshops at conferences, simulation educator courses, formal fellowships in debriefings, or thro...... be used to improve debriefing quality within programs? (5) How can we individualize debriefing training opportunities to the learning needs of our educators?......STATEMENT: Debriefing is widely recognized as a critically important element of simulation-based education. Simulation educators obtain and/or seek debriefing training from various sources, including workshops at conferences, simulation educator courses, formal fellowships in debriefings......, or through advanced degrees. Although there are many options available for debriefing training, little is known about how faculty development opportunities should be structured to maintain and enhance the quality of debriefing within simulation programs. In this article, we discuss 5 key issues to help shape...

A Fortran-77 program for Monte Carlo simulation of upwelling light from the sea

Digital Repository Service at National Institute of Oceanography (India)

Sathe, P.V.; Sathyendranath, S.

for Monte Carlo simulation of spectral and angular composition of upwelling light emerging from a wind-roughened sea under given physical conditions and for a given water quality. The program also simulates the light field prevailing immediately below... constituents of the sea which influence the quality of upwelling light. Because the program is a direct simulation of radiative transfer from the atmosphere to the sea and vice versa, it may be put to a variety of uses in studies in marine optics. Simulated...

PUMN: a radiation damage simulation computer program for the WINERY system

International Nuclear Information System (INIS)

Kuspa, J.P.

1976-01-01

The WINERY Radiation Damage Computer Simulation System will attempt to solve the entire radiation damage problem from the incident radiation to the property changes which occur in the material, using a set of interrelated computer programs. Computer simulation may be indispensable to the study of the radiation damage to materials in breeder and fusion reactors. WINERY is introduced with this work, and one portion of the system, the PUMN program, is developed and used to obtain important radiation damage results with Fe 3 Al crystal. PUMN is a program which simulates the response of the atoms in a crystal to a knock-on atom. It yields the damage configuration of the crystal by considering the dynamic interaction of all the atoms of the computational cell, up to 1000 atoms. The trajectories of the atoms are calculated using the Nordsieck Method, which has a prediction step based upon Taylor series expansions of the position and its first five time derivatives, and has a correction sequence which uses coefficients which have been optimized for efficiency and accuracy. Other features, such as restart files, automatic time step control, and crystal extension, make PUMN a versatile program which can simulate cases of relatively high knock-on energy, at least up to 500 eV. The PUMN program provides the WINERY system with results for the number of displacements, N/sub d/, due to knock-on atoms with various energies. This study dealt exclusively with Fe 3 Al. The values of N/sub d/ for Fe 3 Al were obtained at two different energies, 100 eV and 500 eV, for a variety of initial directions

CHEMSIMUL - A program package for numerical simulation of chemical reaction systems

International Nuclear Information System (INIS)

Lang Rasmussen, O.; Bjergbakke, E.

1984-01-01

A description is given of a program package, CHEMSIMUL, for numerical simulation of chemical reaction systems. The main components in the package are a translator of chemical equations to differential equations, a balance equation program, a differential equation solver, EPISODE, and an input/output program. The performance of the program is demonstrated by four examples. A manual for the input file and the complete program text with comments are given in Appendices I and II. (author)

Final Report: Model interacting particle systems for simulation and macroscopic description of particulate suspensions

Energy Technology Data Exchange (ETDEWEB)

Peter J. Mucha

2007-08-30

Suspensions of solid particles in liquids appear in numerous applications, from environmental settings like river silt, to industrial systems of solids transport and water treatment, and biological flows such as blood flow. Despite their importance, much remains unexplained about these complicated systems. Mucha's research aims to improve understanding of basic properties of suspensions through a program of simulating model interacting particle systems with critical evaluation of proposed continuum equations, in close collaboration with experimentalists. Natural to this approach, the original proposal centered around collaboration with studies already conducted in various experimental groups. However, as was detailed in the 2004 progress report, following the first year of this award, a number of the questions from the original proposal were necessarily redirected towards other specific goals because of changes in the research programs of the proposed experimental collaborators. Nevertheless, the modified project goals and the results that followed from those goals maintain close alignment with the main themes of the original proposal, improving efficient simulation and macroscopic modeling of sedimenting and colloidal suspensions. In particular, the main investigations covered under this award have included: (1) Sedimentation instabilities, including the sedimentation analogue of the Rayleigh-Taylor instability (for heavy, particle-laden fluid over lighter, clear fluid). (2) Ageing dynamics of colloidal suspensions at concentrations above the glass transition, using simplified interactions. (3) Stochastic reconstruction of velocity-field dependence for particle image velocimetry (PIV). (4) Stochastic modeling of the near-wall bias in 'nano-PIV'. (5) Distributed Lagrange multiplier simulation of the 'internal splash' of a particle falling through a stable stratified interface. (6) Fundamental study of velocity fluctuations in sedimentation

PVSIM{copyright}: A simulation program for photovoltaic cells, modules, and arrays

Energy Technology Data Exchange (ETDEWEB)

King, D.L.; Dudley, J.K.; Boyson, W.E.

1996-06-01

An electrical simulation model for photovoltaic cells, modules, and arrays has been developed that will be useful to a wide range of analysts in the photovoltaic industry. The Microsoft{reg_sign} Windows{trademark} based program can be used to analyze individual cells, to analyze the effects of cell mismatch or reverse bias(`hot spot`) heating in modules and to analyze the performance of large arrays of modules including bypass and blocking diodes. User defined statistical variance can be applied to the fundamental parameters used to simulate the cells and diodes. The model is most appropriate for cells that can be accurately modeled using a two-diode equivalent circuit. This paper describes the simulation program and illustrates its versatility with examples.

TRIGASIM: A computer program to simulate a TRIGA Mark I Reactor

International Nuclear Information System (INIS)

Ruby, Lawrence

1992-01-01

A Fortran-77 computer program has been written which simulates the operation of a TRIGA Mark I Reactor. The 'operator' has options at 1-second intervals, of raising rods, lowering rods, maintaining rods steady, dropping a rod, or scramming the reactor. Results are printed to the screen, and to 2 output files - a tabular record and a logarithmic plot of the power. The Point Kinetic Equations are programmed with 6 delayed groups, quasi-static power feedback, and forward differencing. A pulsing option is available, with simulation which employs the Fuchs Model. A pulse-tail model has been devised to simulate behavior for a few minutes following a pulse. Both graphic and tabular output are also available for the pulses. (author)

INDUSTRIAL ROBOT ARM SIMULATION SOFTWARE DEVELOPMENT USING JAVA-3D AND MATLAB SIMULINK PROGRAMMING LANGUAGE

OpenAIRE

Wirabhuana, Arya

2011-01-01

Robot Arms Simulation Software development using Structured Programming Languages, Third Party Language, and Artificial Intelligence Programming Language are the common techniques in simulating robot arms movement. Those three techniques are having its strengths and weaknesses depend on several constraints such as robot type, degree of operation complexity to be simulated, operator skills, and also computer capability. This paper will discuss on Robot Arms Simulation Software (RSS) developmen...

ELSHIM: Program to simulate elastic processes of heavy ions

International Nuclear Information System (INIS)

Van Ginneken, A.

1992-05-01

The Monte Carlo code ELSIM simulates elastic and quasi-elastic, i.e., of limited energy loss, processes of high energy hadrons in a thick target with particular attention to scattering off edges and the like. Its main applications concern accelerator beam loss, beam scraping, etc. Particles which only participate in elastic processes and are then reflected back into the aperture may cause problems elsewhere in the accelerator lattice -- often far removed from where the beam loss occurs. Therefore ELSIM is often run in conjunction with an accelerator tracking program. It can also be used as the first stage in energy deposition studies. For example, when beam is lost in a superconducting magnet ELSIM can provide energy deposition by the incident particles along with a file specifying coordinates and momenta of the inelastic interactions. The latter can then be processed by a program such as CASIM to complete the energy deposition simulation. A new version of this program, called ELSHIM is introduced here which extends ELSIM to include heavy ions as projectiles

Computer simulation program for medium-energy ion scattering and Rutherford backscattering spectrometry

Energy Technology Data Exchange (ETDEWEB)

Nishimura, Tomoaki, E-mail: t-nishi@hosei.ac.jp

2016-03-15

A computer simulation program for ion scattering and its graphical user interface (MEISwin) has been developed. Using this program, researchers have analyzed medium-energy ion scattering and Rutherford backscattering spectrometry at Ritsumeikan University since 1998, and at Rutgers University since 2007. The main features of the program are as follows: (1) stopping power can be chosen from five datasets spanning several decades (from 1977 to 2011), (2) straggling can be chosen from two datasets, (3) spectral shape can be selected as Gaussian or exponentially modified Gaussian, (4) scattering cross sections can be selected as Coulomb or screened, (5) simulations adopt the resonant elastic scattering cross section of {sup 16}O({sup 4}He, {sup 4}He){sup 16}O, (6) pileup simulation for RBS spectra is supported, (7) natural and specific isotope abundances are supported, and (8) the charge fraction can be chosen from three patterns (fixed, energy-dependent, and ion fraction with charge-exchange parameters for medium-energy ion scattering). This study demonstrates and discusses the simulations and their results.

PGOPHER: A program for simulating rotational, vibrational and electronic spectra

International Nuclear Information System (INIS)

Western, Colin M.

2017-01-01

The PGOPHER program is a general purpose program for simulating and fitting molecular spectra, particularly the rotational structure. The current version can handle linear molecules, symmetric tops and asymmetric tops and many possible transitions, both allowed and forbidden, including multiphoton and Raman spectra in addition to the common electric dipole absorptions. Many different interactions can be included in the calculation, including those arising from electron and nuclear spin, and external electric and magnetic fields. Multiple states and interactions between them can also be accounted for, limited only by available memory. Fitting of experimental data can be to line positions (in many common formats), intensities or band contours and the parameters determined can be level populations as well as rotational constants. PGOPHER is provided with a powerful and flexible graphical user interface to simplify many of the tasks required in simulating, understanding and fitting molecular spectra, including Fortrat diagrams and energy level plots in addition to overlaying experimental and simulated spectra. The program is open source, and can be compiled with open source tools. This paper provides a formal description of the operation of version 9.1. - Highlights: • Easy-to-use graphical interface for assigning and understanding molecular spectra. • Simulates rotational and vibrational structure of many types of molecular spectra. • Fits molecular properties to line positions or spectral contours. • Handles linear molecules and symmetric and asymmetric tops. • Handles perturbations, nuclear and electron spin, and electric and magnetic fields.

In situ pediatric trauma simulation: assessing the impact and feasibility of an interdisciplinary pediatric in situ trauma care quality improvement simulation program.

Science.gov (United States)

Auerbach, Marc; Roney, Linda; Aysseh, April; Gawel, Marcie; Koziel, Jeannette; Barre, Kimberly; Caty, Michael G; Santucci, Karen

2014-12-01

This study aimed to evaluate the feasibility and measure the impact of an in situ interdisciplinary pediatric trauma quality improvement simulation program. Twenty-two monthly simulations were conducted in a tertiary care pediatric emergency department with the aim of improving the quality of pediatric trauma (February 2010 to November 2012). Each session included 20 minutes of simulated patient care, followed by 30 minutes of debriefing that focused on teamwork, communication, and the identification of gaps in care. A single rater scored the performance of the team in real time using a validated assessment instrument for 6 subcomponents of care (teamwork, airway, intubation, breathing, circulation, and disability). Participants completed a survey and written feedback forms. A trend analysis of the 22 simulations found statistically significant positive trends for overall performance, teamwork, and intubation subcomponents; the strength of the upward trend was the strongest for the teamwork (τ = 0.512), followed by overall performance (τ = 0.488) and intubation (τ = 0.433). Two hundred fifty-one of 398 participants completed the participant feedback form (response rate, 63%), reporting that debriefing was the most valuable aspect of the simulation. An in situ interdisciplinary pediatric trauma simulation quality improvement program resulted in improved validated trauma simulation assessment scores for overall performance, teamwork, and intubation. Participants reported high levels of satisfaction with the program, and debriefing was reported as the most valuable component of the program.

Three-Dimensional Simulations of Oblique Asteroid Impacts into Water

Science.gov (United States)

Gisler, G. R.; Ferguson, J. M.; Heberling, T.; Plesko, C. S.; Weaver, R.

2016-12-01

Waves generated by impacts into oceans may represent the most significant danger from near-earth asteroids and comets. For impacts near populated shores, the crown splash and subsequent waves, accompanied by sediment lofting and high winds, could be more damaging than storm surges from the strongest hurricanes. For asteroids less than 500 m in diameter that impact into deep water far from shores, the waves produced will be detectable over large distances, but probably not significantly dangerous. We present new three-dimensional simulations of oblique impacts into deep water, with trajectory angles ranging from 20 degrees to 60 degrees (where 90 degrees is vertical). These simulations are performed with the Los Alamos Rage hydrocode, and include atmospheric effects including ablation and airbursts. These oblique impact simulations are specifically performed in order to help determine whether there are additional dangers from the obliquity of impact not covered by previous two-dimensional studies. Water surface elevation profiles, surface pressures, and depth-averaged mass fluxes within the water are prepared for use in propagation studies.

Enhancing Student Engagement through Simulation in Programming Sessions

Science.gov (United States)

Isiaq, Sakirulai Olufemi; Jamil, Md Golam

2018-01-01

Purpose: The purpose of this paper is to explore the use of a simulator for teaching programming to foster student engagement and meaningful learning. Design/methodology/approach: An exploratory mixed-method research approach was adopted in a classroom-based environment at a UK university. A rich account of student engagement dimensions…

STEFINS: a steel freezing integral simulation program

International Nuclear Information System (INIS)

Frank, M.V.

1980-09-01

STEFINS (STEel Freezing INtegral Simulation) is a computer program for the calculation of the rate of solidification of molten steel on solid steel. Such computations arize when investigating core melt accidents in fast reactors. In principle this problem involves a coupled two-dimensional thermal and hydraulic approach. However, by physically reasonable assumptions a decoupled approach has been developed. The transient solidification of molten steel on a cold wall is solved in the direction normal to the molten steel flow and independent from the solution for the molten steel temperature and Nusselt number along the direction of flow. The solutions to the applicable energy equations have been programmed in cylindrical and slab geometries. Internal gamma heating of steel is included

Eight critical factors in creating and implementing a successful simulation program.

Science.gov (United States)

Lazzara, Elizabeth H; Benishek, Lauren E; Dietz, Aaron S; Salas, Eduardo; Adriansen, David J

2014-01-01

Recognizing the need to minimize human error and adverse events, clinicians, researchers, administrators, and educators have strived to enhance clinicians' knowledge, skills, and attitudes through training. Given the risks inherent in learning new skills or advancing underdeveloped skills on actual patients, simulation-based training (SBT) has become an invaluable tool across the medical education spectrum. The large simulation, training, and learning literature was used to provide a synthesized yet innovative and "memorable" heuristic of the important facets of simulation program creation and implementation, as represented by eight critical "S" factors-science, staff, supplies, space, support, systems, success, and sustainability. These critical factors advance earlier work that primarily focused on the science of SBT success, to also include more practical, perhaps even seemingly obvious but significantly challenging components of SBT, such as resources, space, and supplies. SYSTEMS: One of the eight critical factors-systems-refers to the need to match fidelity requirements to training needs and ensure that technological infrastructure is in place. The type of learning objectives that the training is intended to address should determine these requirements. For example, some simulators emphasize physical fidelity to enable clinicians to practice technical and nontechnical skills in a safe environment that mirrors real-world conditions. Such simulators are most appropriate when trainees are learning how to use specific equipment or conduct specific procedures. The eight factors-science, staff, supplies, space, support, systems, success, and sustainability-represent a synthesis of the most critical elements necessary for successful simulation programs. The order of the factors does not represent a deliberate prioritization or sequence, and the factors' relative importance may change as the program evolves.

How a Fully Automated eHealth Program Simulates Three Therapeutic Processes: A Case Study.

Science.gov (United States)

Holter, Marianne T S; Johansen, Ayna; Brendryen, Håvar

2016-06-28

eHealth programs may be better understood by breaking down the components of one particular program and discussing its potential for interactivity and tailoring in regard to concepts from face-to-face counseling. In the search for the efficacious elements within eHealth programs, it is important to understand how a program using lapse management may simultaneously support working alliance, internalization of motivation, and behavior maintenance. These processes have been applied to fully automated eHealth programs individually. However, given their significance in face-to-face counseling, it may be important to simulate the processes simultaneously in interactive, tailored programs. We propose a theoretical model for how fully automated behavior change eHealth programs may be more effective by simulating a therapist's support of a working alliance, internalization of motivation, and managing lapses. We show how the model is derived from theory and its application to Endre, a fully automated smoking cessation program that engages the user in several "counseling sessions" about quitting. A descriptive case study based on tools from the intervention mapping protocol shows how each therapeutic process is simulated. The program supports the user's working alliance through alliance factors, the nonembodied relational agent Endre and computerized motivational interviewing. Computerized motivational interviewing also supports internalized motivation to quit, whereas a lapse management component responds to lapses. The description operationalizes working alliance, internalization of motivation, and managing lapses, in terms of eHealth support of smoking cessation. A program may simulate working alliance, internalization of motivation, and lapse management through interactivity and individual tailoring, potentially making fully automated eHealth behavior change programs more effective.

Development of a multi-media crew-training program for the terminal configured vehicle mission simulator

Science.gov (United States)

Rhouck, J. A.; Markos, A. T.

1980-01-01

This paper describes the work being done at the National Aeronautics and Space Administration's (NASA) Langley Research Center on the development of a multi-media crew-training program for the Terminal Configured Vehicle (TCV) Mission Simulator. Brief descriptions of the goals and objectives of the TCV Program and of the TCV Mission Simulator are presented. A detailed description of the training program is provided along with a description of the performance of the first group of four commercial pilots to be qualified in the TCV Mission Simulator.

Fault-Tolerant Robot Programming through Simulation with Realistic Sensor Models

Directory of Open Access Journals (Sweden)

Axel Waggershauser

2008-11-01

Full Text Available We introduce a simulation system for mobile robots that allows a realistic interaction of multiple robots in a common environment. The simulated robots are closely modeled after robots from the EyeBot family and have an identical application programmer interface. The simulation supports driving commands at two levels of abstraction as well as numerous sensors such as shaft encoders, infrared distance sensors, and compass. Simulation of on-board digital cameras via synthetic images allows the use of image processing routines for robot control within the simulation. Specific error models for actuators, distance sensors, camera sensor, and wireless communication have been implemented. Progressively increasing error levels for an application program allows for testing and improving its robustness and fault-tolerance.

General Tokamak Circuit Simulation Program-GTCSP

International Nuclear Information System (INIS)

Matsukawa, Makoto; Miura, Yushi; Aoyagi, Tetsuo.

1997-05-01

General Tokamak Circuit Simulation Program (GTCSP) was originally developed for the design work of JT-60 Power Supply System in JAERI. Therefore the prepared models (components) to be analyzed are generator, thyristor converter and coils. This is one of the unique points of GTCSP in comparison with other conventional electric circuit analysis program, because they make a circuit from the small devices such as resister, coil, condenser, transistor and so on. However, GTCSP is also clearly conventional because it is possible to construct an electric circuit freely with the prepared components. Moreover, a similar function could be realized by addition a new component to GTCSP. This report is assumed to be used as an User Manual of the GTCSP, not only to present the development and the analytical functions. Then some useful examples are described, and how to get graphic outputs are also mentioned. (author)

Lifetime prediction of structures submitted to thermal fatigue loadings; Prediction de duree de vie de structures sous chargement de fatigue thermique

Energy Technology Data Exchange (ETDEWEB)

Amiable, S

2006-01-15

The aim of this work is to predict the lifetime of structures submitted to thermal fatigue loadings. This work lies within the studies undertaken by the CEA on the thermal fatigue problems from the french reactor of Civaux. In particular we study the SPLASH test: a specimen is heated continuously and cyclically cooled down by a water spray. This loading generates important temperature gradients in space and time and leads to the initiation and the propagation of a crack network. We propose a new thermo-mechanical model to simulate the SPLASH experiment and we propose a new fatigue criterion to predict the lifetime of the SPLASH specimen. We propose and compare several numerical models with various complexity to estimate the mechanical response of the SPLASH specimen. The practical implications of this work are the reevaluation of the hypothesis used in the French code RCC, which are used to simulate thermal shock and to interpret the results in terms of fatigue. This work leads to new perspectives on the mechanical interpretation of the fatigue criterion. (author)

Lifetime prediction of structures submitted to thermal fatigue loadings

International Nuclear Information System (INIS)

Amiable, S.

2006-01-01

The aim of this work is to predict the lifetime of structures submitted to thermal fatigue loadings. This work lies within the studies undertaken by the CEA on the thermal fatigue problems from the french reactor of Civaux. In particular we study the SPLASH test: a specimen is heated continuously and cyclically cooled down by a water spray. This loading generates important temperature gradients in space and time and leads to the initiation and the propagation of a crack network. We propose a new thermo-mechanical model to simulate the SPLASH experiment and we propose a new fatigue criterion to predict the lifetime of the SPLASH specimen. We propose and compare several numerical models with various complexity to estimate the mechanical response of the SPLASH specimen. The practical implications of this work are the reevaluation of the hypothesis used in the French code RCC, which are used to simulate thermal shock and to interpret the results in terms of fatigue. This work leads to new perspectives on the mechanical interpretation of the fatigue criterion. (author)

RadSim: a program to simulate individual particle interactions for educational purposes

International Nuclear Information System (INIS)

Verhaegen, Frank; Palefsky, Steven; DeBlois, Francois

2006-01-01

A program was developed, RadSim, which can be used to simulate certain individual interactions of photons, electrons, positrons and alpha particles with a single atom for educational purposes. The program can be run in two modes: manual and simulated. In the manual mode, an individual particle undergoing a specified interaction with a target atom can be simulated, which essentially comes down to a graphical evaluation of kinematic equations. In the simulated mode, a preset number of identical particles are allowed to undergo a specified interaction type with a target atom. The exit channel of the interaction is sampled from probability distributions using Monte Carlo methods. The incoming and outgoing particles are visualized and the frequency distribution of the kinematic variables of the exit channel is displayed graphically. It has to be emphasized that RadSim was mainly developed for educational purposes. (note)

Development of the NSSS thermal-hydraulic program for YGN unit 1 simulator

Energy Technology Data Exchange (ETDEWEB)

Kim, Kyung Doo; Jeong, Jae Jun; Lee, Won Jae; Chung, Bub Dong; Ha, Kwi Seok; Kang, Kyung Ho

2000-09-01

The NSSS thermal-hydraulic programs installed in the domestic full-scope power plant simulators were provided in early 1980s by foreign vendors. Because of limited computational capability at that time, they usually adopt very simplified physical models for a real-time simulation of NSSS thermal-hydraulic phenomena, which entails inaccurate results and the possibility of so-called 'negative training', especially for complicated two-phase flows in the reactor coolant system. To resolve the problem, we developed a realistic NSSS T/H program (named 'ARTS' code) for use in YongGwang Nuclear Unit 1 full-scope simulator. The best-estimate code RETRAN03, developed by EPRI and approved by USNRC, was selected as a reference code of ARTS. For the development of ARTS, the followings have been performed: -Improvement of the robustness of RETRAN - Improvement of the real-time simulation capability of RETRAN - Optimum input data generation for the NSSS simulation - New model development that cannot be efficiently modeled by RETRAN - Assessment of the ARTS code. The systematic assessment of ARTS has been conducted in both personal computers (Windows 98, Visual fortran) and the simulator development environment (Windows NT, GSE simulator development tool). The results were resonable in terms of accuracy, real-time simulation and robustness.

Development of the NSSS thermal-hydraulic program for YGN unit 1 simulator

International Nuclear Information System (INIS)

Kim, Kyung Doo; Jeong, Jae Jun; Lee, Won Jae; Chung, Bub Dong; Ha, Kwi Seok; Kang, Kyung Ho

2000-09-01

The NSSS thermal-hydraulic programs installed in the domestic full-scope power plant simulators were provided in early 1980s by foreign vendors. Because of limited computational capability at that time, they usually adopt very simplified physical models for a real-time simulation of NSSS thermal-hydraulic phenomena, which entails inaccurate results and the possibility of so-called 'negative training', especially for complicated two-phase flows in the reactor coolant system. To resolve the problem, we developed a realistic NSSS T/H program (named 'ARTS' code) for use in YongGwang Nuclear Unit 1 full-scope simulator. The best-estimate code RETRAN03, developed by EPRI and approved by USNRC, was selected as a reference code of ARTS. For the development of ARTS, the followings have been performed: -Improvement of the robustness of RETRAN - Improvement of the real-time simulation capability of RETRAN - Optimum input data generation for the NSSS simulation - New model development that cannot be efficiently modeled by RETRAN - Assessment of the ARTS code. The systematic assessment of ARTS has been conducted in both personal computers (Windows 98, Visual fortran) and the simulator development environment (Windows NT, GSE simulator development tool). The results were resonable in terms of accuracy, real-time simulation and robustness

DESIGN OF AN EDUCATIONAL SIMULATION PROGRAM USING DIGITAL VIDEO PROCESSING TO DETERMINE THE THERMAL EXPANSION OF MATERIALS

Directory of Open Access Journals (Sweden)

V. Gökhan BÖCEKÇİ

2013-01-01

Full Text Available The present report describes the realization of an educational simulation program to determine the amount of linear thermal expansion in experimental materials. An interferogram signal derived from an interferometric measurement system was modeled as a video signal in a computer environment. A simulation program was designed from the model signal in order to detect the amount of expansion in materials. The simulation program determined the amount of to heat by detecting the number of fringes in interferogram video signals of the material. This simulation program facilitated experimental studies n academic institutions which are deprived of interferometric measurement systems.

A users guide to the SIMULATION data assembler program

International Nuclear Information System (INIS)

Goodill, D.R.; Tymons, B.J.

1984-09-01

SIMULATION is a computer program that has been developed by Central Technical Services, UKAEA, Risley, to provide a method of analysis for any radioactive waste management system. The program models a complete system by taking any number of raw waste streams through any sequence of operations, such as treatment or conditioning, packaging or transport. Results are produced in terms of the quantity of waste in each store and the waste throughput of each process on a year by year basis. (author)

Simulation of reduced breast cancer mortality in breast cancer screening programs

International Nuclear Information System (INIS)

Zamora, L. I.; Forastero, C.; Guirado, D.; Lallena, A. M.

2011-01-01

The breast cancer screening programs are an essential tool in the fight against breast cancer. Currently, many questions concerning the setup of these programs are open, namely: age range of women who undergo the same, frequency of mammography, ... The effectiveness of a program should be evaluated in terms of mortality reduction is its systematic implementation in the population. In this sense, we performed Monte Carlo simulations to assess that these reductions.

MARLOWE: a computer simulation program in the BCA and it's application

International Nuclear Information System (INIS)

Zhou Peng; Pan Zhengying; Huo Yukun

1988-01-01

MARLOWE is a computer program for simulation of atomic-displacement cascades in a variety of solids based upon binary-collision approximation. This paper briefs the program including it's theoretical background, approximation adopted, features and applicable scope. In addition, we outline a number of physical problems we studied with this code

A simple interface to computational fluid dynamics programs for building environment simulations

Energy Technology Data Exchange (ETDEWEB)

Broderick, III, C R; Chen, Q [Massachusetts Institute of Technology, Cambridge, MA (United States)

2000-07-01

It is becoming a popular practice for architects and HVAC engineers to simulate airflow in and around buildings by computational fluid dynamics (CFD) methods in order to predict indoor and outdoor environment. However, many CFD programs are crippled by a historically poor and inefficient user interface system, particularly for users with little training in numerical simulation. This investigation endeavors to create a simplified CFD interface (SCI) that allows architects and buildings engineers to use CFD without excessive training. The SCI can be easily integrated into new CFD programs. (author)

Virtual Property Manager: Providing a Simulated Learning Environment in a New University Program of Study

Directory of Open Access Journals (Sweden)

Andrew Carswell

2007-08-01

Full Text Available This paper relates the experience that students have while accessing Virtual Property Manager (VPM, a Web-based simulation learning tool designed to introduce students to a new discipline being offered at the university – Residential Property Management. The VPM simulation was designed in part to develop student interest in the new program. Results indicate that this simple simulation device did make a notable impact on student interest. Additionally, student acceptance and self-reported impact differed significantly based upon the delivery context. Adding a competitive reward element to the simulation experience improved student's evaluation of the software and self-reported interest in the field. Results indicate that educational simulation evaluation, acceptance, and performance may often be substantially influenced by the delivery context, rather than simply the program itself. Developers may do well to focus "outside the box" of program content to promote audience-specific delivery environments.

Monte Carlo and detector simulation in OOP [Object-Oriented Programming

International Nuclear Information System (INIS)

Atwood, W.B.; Blankenbecler, R.; Kunz, P.; Burnett, T.; Storr, K.M.

1990-10-01

Object-Oriented Programming techniques are explored with an eye toward applications in High Energy Physics codes. Two prototype examples are given: McOOP (a particle Monte Carlo generator) and GISMO (a detector simulation/analysis package)

Water Quality Assessment Simulation Program (WASP8): Upgrades to the Advanced Toxicant Module for Simulating Dissolved Chemicals, Nanomaterials, and Solids

Science.gov (United States)

The Water Quality Analysis Simulation Program (WASP) is a dynamic, spatially-resolved, differential mass balance fate and transport modeling framework. WASP is used to develop models to simulate concentrations of environmental contaminants in surface waters and sediments. As a mo...

SITHA program for simulating hadron transport in the 100-1010eV energy range. Simulation of neutron transport with E6 eV

International Nuclear Information System (INIS)

Daniehl', A.V.; Dushin, V.N.

1987-01-01

The methods for simulation of neutron transport with Z<20 MeV used in the SITHA (simulation transport hadron) program, the original library of group microconstants (175 groups) with subgroup description of resonance range and a set of programs for its creation are described. The results of a number of integral experiments are discussed

An intelligent environment for dynamic simulation program generation of nuclear reactor systems

International Nuclear Information System (INIS)

Ishizaka, Hiroaki; Gofuku, Akio; Yoshikawa, Hidekazu

2004-01-01

A graphical user interface system was developed for the two dynamic simulation systems based on modular programming methods: MSS and DSNP. The following works were made in conjunction with the system development: (1) conversion of the module libraries of both DSNP and MSS, (2) extension of DSNP- pre-compiler, (3) graphical interface for module integration, and (4) automatic converter of simple language descriptions for DSNP, where (1) and (2) were made on an engineering work station, while the rest (3) and (4), on Macintosh HyperCard. By using the graphical interface, a user can specify the structure of a simulation model, geometrical data, initial values of variables, etc. only by handling modules as icon on the pallet fields. The use of extended DSNP pre-compiler then generates the final product of dynamic simulation program automatically. The capability and effectiveness of the system was confirmed by a sample simulation of PWR SBLOCA transient in PORV stuck open event. (author)

The Application of Visual Basic Computer Programming Language to Simulate Numerical Iterations

Directory of Open Access Journals (Sweden)

Abdulkadir Baba HASSAN

2006-06-01

Full Text Available This paper examines the application of Visual Basic Computer Programming Language to Simulate Numerical Iterations, the merit of Visual Basic as a Programming Language and the difficulties faced when solving numerical iterations analytically, this research paper encourage the uses of Computer Programming methods for the execution of numerical iterations and finally fashion out and develop a reliable solution using Visual Basic package to write a program for some selected iteration problems.

Design and evaluation of simulation scenarios for a program introducing patient safety, teamwork, safety leadership, and simulation to healthcare leaders and managers.

Science.gov (United States)

Cooper, Jeffrey B; Singer, Sara J; Hayes, Jennifer; Sales, Michael; Vogt, Jay W; Raemer, Daniel; Meyer, Gregg S

2011-08-01

We developed a training program to introduce managers and informal leaders of healthcare organizations to key concepts of teamwork, safety leadership, and simulation to motivate them to act as leaders to improve safety within their sphere of influence. This report describes the simulation scenario and debriefing that are core elements of that program. Twelve teams of clinician and nonclinician managers were selected from a larger set of volunteers to participate in a 1-day, multielement training program. Two simulation exercises were developed: one for teams of nonclinicians and the other for clinicians or mixed groups. The scenarios represented two different clinical situations, each designed to engage participants in discussions of their safety leadership and teamwork issues immediately after the experience. In the scenarios for nonclinicians, participants conducted an anesthetic induction and then managed an ethical situation. The scenario for clinicians simulated a consulting visit to an emergency room that evolved into a problem-solving challenge. Participants in this scenario had a limited time to prepare advice for hospital leadership on how to improve observed safety and cultural deficiencies. Debriefings after both types of scenarios were conducted using principles of "debriefing with good judgment." We assessed the relevance and impact of the program by analyzing participant reactions to the simulation through transcript data and facilitator observations as well as a postcourse questionnaire. The teams generally reported positive perceptions of the relevance and quality of the simulation with varying types and degrees of impact on their leadership and teamwork behaviors. These kinds of clinical simulation exercises can be used to teach healthcare leaders and managers safety leadership and teamwork skills and behaviors.

Modelling of windmill induction generators in dynamic simulation programs

DEFF Research Database (Denmark)

Akhmatov, Vladislav; Knudsen, Hans

1999-01-01

with and without a model of the mechanical shaft. The reason for the discrepancies are explained, and it is shown that the phenomenon is due partly to the presence of DC offset currents in the induction machine stator, and partly to the mechanical shaft system of the wind turbine and the generator rotor......For AC networks with large amounts of induction generators-in case of e.g. windmills-the paper demonstrates a significant discrepancy in the simulated voltage recovery after faults in weak networks, when comparing result obtained with dynamic stability programs and transient programs, respectively....... It is shown that it is possible to include a transient model in dynamic stability programs and thus obtain correct results also in dynamic stability programs. A mechanical model of the shaft system has also been included in the generator model...

Using Software Zelio Soft in Educational Process to Simulation Control Programs for Intelligent Relays

Science.gov (United States)

Michalik, Peter; Mital, Dusan; Zajac, Jozef; Brezikova, Katarina; Duplak, Jan; Hatala, Michal; Radchenko, Svetlana

2016-10-01

Article deals with point to using intelligent relay and PLC systems in practice, to their architecture and principles of programming and simulations for education process on all types of school from secondary to universities. Aim of the article is proposal of simple examples of applications, where is demonstrated methodology of programming on real simple practice examples and shown using of chosen instructions. In practical part is described process of creating schemas and describing of function blocks, where are described methodologies of creating program and simulations of output reactions on changeable inputs for intelligent relays.

Flight simulation program for high altitude long endurance unmanned vehicle; Kokodo mujinki no hiko simulation program

Energy Technology Data Exchange (ETDEWEB)

Suzuki, H.; Hashidate, M. [National Aerospace Laboratory, Tokyo (Japan)

1995-11-01

An altitude of about 20 km has the atmospheric density too dilute for common aircraft, and the air resistance too great for satellites. Attention has been drawn in recent years on a high-altitude long-endurance unmanned vehicle that flies at this altitude for a long period of time to serve as a wave relaying base and perform traffic control. Therefore, a development was made on a flight simulation program to evaluate and discuss the guidance and control laws for the high-altitude unmanned vehicle. Equations of motion were derived for three-dimensional six freedom and three-dimensional three freedom. Aerodynamic characteristics of an unmanned vehicle having a Rectenna wing were estimated, and formulation was made according to the past research results on data of winds that the unmanned vehicle is anticipated to encounter at an altitude of 20 km. Noticing the inside of a horizontal plane, a proposal was given on a guidance law that follows a given path. A flight simulation was carried out to have attained a prospect that the unmanned vehicle may be enclosed in a limited space even if the vehicle is encountered with a relatively strong wind. 18 refs., 20 figs., 1 tab.

LIAR: A COMPUTER PROGRAM FOR THE SIMULATION AND MODELING OF HIGH PERFORMANCE LINACS

International Nuclear Information System (INIS)

Adolphsen, Chris

2003-01-01

The computer program LIAR (''LInear Accelerator Research code'') is a numerical simulation and tracking program for linear colliders. The LIAR project was started at SLAC in August 1995 in order to provide a computing and simulation tool that specifically addresses the needs of high energy linear colliders. LIAR is designed to be used for a variety of different linear accelerators. It has been applied for and checked against the existing Stanford Linear Collider (SLC) as well as the linacs of the proposed Next Linear Collider (NLC) and the proposed Linac Coherent Light Source (LCLS). The program includes wakefield effects, a 4D coupled beam description, specific optimization algorithms and other advanced features. We describe the most important concepts and highlights of the program. After having presented the LIAR program at the LINAC96 and the PAC97 conferences, we do now introduce it to the European particle accelerator community

Coaching the Debriefer: Peer Coaching to Improve Debriefing Quality in Simulation Programs.

Science.gov (United States)

Cheng, Adam; Grant, Vincent; Huffman, James; Burgess, Gavin; Szyld, Demian; Robinson, Traci; Eppich, Walter

2017-10-01

Formal faculty development programs for simulation educators are costly and time-consuming. Peer coaching integrated into the teaching flow can enhance an educator's debriefing skills. We provide a practical guide for the who, what, when, where, why, and how of peer coaching for debriefing in simulation-based education. Peer coaching offers advantages such as psychological safety and team building, and it can benefit both the educator who is receiving feedback and the coach who is providing it. A feedback form for effective peer coaching includes the following: (1) psychological safety, (2) framework, (3) method/strategy, (4) content, (5) learner centeredness, (6) co-facilitation, (7) time management, (8) difficult situations, (9) debriefing adjuncts, and (10) individual style and experience. Institutional backing of peer coaching programs can facilitate implementation and sustainability. Program leaders should communicate the need and benefits, establish program goals, and provide assessment tools, training, structure, and evaluation to optimize chances of success.

DBSSP - A computer program for simulation of controlled circulation boiler and natural circulation boiler start up behavior

International Nuclear Information System (INIS)

Li Bin; Chen Tingkuan; Yang Dong

2005-01-01

In this paper, a computer program, Drum Boiler Start-up Simulation Program (DBSSP), is developed for simulating the start up behavior of controlled circulation and natural circulation boilers. The mathematical model developed here is based on the first principles of mass, energy and momentum conservations. In the boiler model, heat transfer in the waterwall, the superheater, the reheater and the economizer is simulated by the distributing parameter method, while heat transfer in the drum and the downcomer is simulated by lumped parameter analysis. The program can provide detailed flow and thermodynamic characteristics of the boiler components. The development of this program is based only on design data, so it can be used for any subcritical, controlled or natural circulation boiler. The simulation results were compared with experimental measurements, and good agreements between them were found. This program is expected to be useful for predicting the characteristics and the performance of controlled circulation and natural circulation boilers during the start up process. It also can be used to optimize a start up system for minimum start up time

A Microcomputer Program that Simulates the Baumol-Tobin Transactions Demand for Money.

Science.gov (United States)

Beckman, Steven

1987-01-01

This article describes an economic model dealing with the demand for money and a microcomputer program which enables students to experiment with cash management techniques. By simulating personal experiences, the program teaches how changes in income, interest rates, and charges for exchanging bonds and cash affect money demand. (Author/JDH)

FD_BH: a program for simulating electromagnetic waves from a borehole antenna

Science.gov (United States)

Ellefsen, Karl J.

2002-01-01

Program FD_BH is used to simulate the electromagnetic waves generated by an antenna in a borehole. The model representing the antenna may include metallic parts, a coaxial cable as a feed to the driving point, and resistive loading. The program is written in the C programming language, and the program has been tested on both the Windows and the UNIX operating systems. This Open-File Report describes • The contents and organization of the Zip file (section 2). • The program files, the installation of the program, the input files, and the execution of the program (section 3). • Address to which suggestions for improving the program may be sent (section 4).

DSNP, Program and Data Library System for Dynamic Simulation of Nuclear Power Plant

International Nuclear Information System (INIS)

Saphier, D.; Madell, J.; Dean, E.

1988-01-01

1 - Description of problem or function: DSNP (Dynamic Simulator for Nuclear Power-Plants) is a system of programs and data files by which a nuclear power plant, or part thereof, can be simulated. The acronym DSNP is used interchangeably for the DSNP language, the DSNP libraries, the DSNP pre-compiler, and the DSNP document generator. The DSNP language is a special-purpose, block-oriented digital- simulation language developed to facilitate the preparation of dynamic simulations of a large variety of nuclear power plants. It is a user-oriented language that permits the user to prepare simulation programs directly from power plant block diagrams and flow charts by recognizing the symbolic DSNP statements for the appropriate physical components and listing these statements in a logical sequence according to the flow of physical properties in the simulated power plant. Physical components of nuclear power plants are represented by functional blocks, or modules. Many of the more complex components are represented by several modules. The nuclear reactor, for example, has a kinetic module, a power distribution module, a feedback module, a thermodynamic module, a hydraulic module, and a radioactive heat decay module. These modules are stored in DSNP libraries in the form of a DSNP subroutine or function, a block of statements, a macro, or a combination of the above. Basic functional blocks such as integrators, pipes, function generators, connectors, and many auxiliary functions representing properties of materials used in nuclear power plants are also available. The DSNP pre-compiler analyzes the DSNP simulation program, performs the appropriate translations, inserts the requested modules from the library, links these modules together, searches necessary data files, and produces a simulation program in FORTRAN. FORTRAN is considered to be a subset of DSNP and can be inserted anywhere in the simulation program without restriction. I/O statements can be located anywhere in

Transiout simulation program PHOTO for hybrid plants. Hybridilaitosten simulointi- ja mitoitusohjelmisto PHOTO; Dokumentti ja kaeyttoeohje

Energy Technology Data Exchange (ETDEWEB)

Manninen, L M; Lund, P D

1988-09-01

The sizing and design of photovoltaic and wind power systems are often approached by simple methods which employ mean monthly weather data and the autonomy time requirement as the basis for the performance predictions. These models do not provide any information on system reliability, which is a most important factor for practical installations. To give further insight on the operational reliability of photovoltaic and wind power systems, new design models and simulation tools have been developed. A leading feature in the work has been to consider the system as a whole, that is, to model all the subsystems and controls, and to account correctly for the subsystem interactions. The set of programs described in this report comprise a stochastic weather generating routine WESIM which provides hourly data from generally available monthly weather data. A parametrization procedure for solar cells is incorporated in the program set. Program FITSOL is applied to fit parameters of the model for solar cell current-coltage characteristics. The use of theoretical model instead of tabulated values simplifies the simulation procedure. Transient simulation program PHOTO is employed to calculate system performance as a function of time. Simulation program provides an accurate estimate on the various energy flows, battery performance etc. The individual subsystem models have been verified against real measurements.

Barriers to the implementation and uptake of simulation-based training programs in general surgery: a multinational qualitative study.

Science.gov (United States)

Hosny, Shady G; Johnston, Maximilian J; Pucher, Philip H; Erridge, Simon; Darzi, Ara

2017-12-01

Despite evidence demonstrating the advantages of simulation training in general surgery, it is not widely integrated into surgical training programs worldwide. The aim of this study was to identify barriers and facilitators to the implementation and uptake of surgical simulation training programs. A multinational qualitative study was conducted using semi-structured interviews of general surgical residents and experts. Each interview was audio recorded, transcribed verbatim, and underwent emergent theme analysis. All data were anonymized and results pooled. A total of 37 individuals participated in the study. Seventeen experts (Program Directors and Surgical Attendings with an interest in surgical education) and 20 residents drawn from the United States, Canada, United Kingdom, France, and Japan were interviewed. Barriers to simulation-based training were identified based on key themes including financial cost, access, and translational benefit. Participants described cost (89%) and access (76%) as principal barriers to uptake. Common facilitators included a mandatory requirement to complete simulation training (78%) and on-going assessment of skills (78%). Participants felt that simulation training could improve patient outcomes (76%) but identified a lack of evidence to demonstrate benefit (38%). There was a consensus that simulation training has not been widely implemented (70%). There are multiple barriers to the implementation of surgical simulation training programs, however, there is agreement that these programs could potentially improve patient outcomes. Identifying these barriers enable the targeted use of facilitators to deliver simulation training programs. Copyright © 2017 Elsevier Inc. All rights reserved.

Simulation of a programmed frequency shift near extraction from the Fermilab Booster

International Nuclear Information System (INIS)

Lucas, P.; Kerns, Q.

1987-03-01

The longitudinal phase space program ESME has been used to simulate the effects of a linear shift in RF frequency away from that appropriate for the accelerator guide field. This shift takes place in the new Booster low level RF and is used to position the particle bunches in Main Ring buckets in a reproducible fashion. Shifts in frequency are found to generate synchrotron oscillations; however, the simulations show that these can be reduced to acceptable levels by introduction of jumps in RF phase preceding the programmed frequency changes. Lowering the RF voltage near extraction from the Booster, a desirable operational feature, has also been investigated

Use of a surface contamination survey simulation program and its effects

International Nuclear Information System (INIS)

Onuma, Isamu; Kobayashi, Makoto; Umehara, Takashi; Shimizu, Isamu

2012-01-01

A computer simulation program has been developed to train the practitioners examining the surface contamination of objects to be carried out from the controlled area. The efficiency of the examination depends significantly on the proficiency in radiation measurement and proper perception of contamination. It has been demonstrated through the usage of the program that it helps practitioners very much suggest their weakness and promote their skill in examination. The program runs on the commonly used personal computers and users can easily experience the virtual examination by sweeping and cricking the mouse. The program is useful to radiation protection practitioners not only beginners but also experts. (author)

Nuclear Human Resources Development Program using Educational Core Simulator

International Nuclear Information System (INIS)

Choi, Yu Sun; Hong, Soon Kwan

2015-01-01

KHNP-CRI(Korea Hydro and Nuclear Power Co.-Central Research Institute) has redesigned the existing Core Simulator(CoSi) used as a sort of training tools for reactor engineers in operating nuclear power plant to support Nuclear Human Resources Development (NHRD) Program focusing on the nuclear department of Dalat university in Vietnam. This program has been supported by MOTIE in Korea and cooperated with KNA(Korea Nuclear Association for International Cooperation) and HYU(Hanyang University) for enhancing the nuclear human resources of potential country in consideration with Korean Nuclear Power Plant as a next candidate energy sources. KHNP-CRI has provided Edu-CoSi to Dalat University in Vietnam in order to support Nuclear Human Resources Development Program in Vietnam. Job Qualification Certificates Program in KHNP is utilized to design a training course for Vietnamese faculty and student of Dalat University. Successfully, knowhow on lecturing the ZPPT performance, training and maintaining Edu-CoSi hardware are transferred by several training courses which KHNP-CRI provides

Nuclear Human Resources Development Program using Educational Core Simulator

Energy Technology Data Exchange (ETDEWEB)

Choi, Yu Sun; Hong, Soon Kwan [KHNP-CRI, Daejeon (Korea, Republic of)

2015-10-15

KHNP-CRI(Korea Hydro and Nuclear Power Co.-Central Research Institute) has redesigned the existing Core Simulator(CoSi) used as a sort of training tools for reactor engineers in operating nuclear power plant to support Nuclear Human Resources Development (NHRD) Program focusing on the nuclear department of Dalat university in Vietnam. This program has been supported by MOTIE in Korea and cooperated with KNA(Korea Nuclear Association for International Cooperation) and HYU(Hanyang University) for enhancing the nuclear human resources of potential country in consideration with Korean Nuclear Power Plant as a next candidate energy sources. KHNP-CRI has provided Edu-CoSi to Dalat University in Vietnam in order to support Nuclear Human Resources Development Program in Vietnam. Job Qualification Certificates Program in KHNP is utilized to design a training course for Vietnamese faculty and student of Dalat University. Successfully, knowhow on lecturing the ZPPT performance, training and maintaining Edu-CoSi hardware are transferred by several training courses which KHNP-CRI provides.

Development of the Dutch Johne's disease control program supported by a simulation model

NARCIS (Netherlands)

Groenendaal, H.; Nielen, M.; Hesselink, J.W.

2003-01-01

The development of a simulation model, "JohneSSim", was part of a research program aimed at designing a national Johne's disease control program for The Netherlands. Initially, the focus was mainly directed towards different compulsory "test-and-cull" strategies. However, the results from the

MODLP program description: A program for solving linear optimal hydraulic control of groundwater contamination based on MODFLOW simulation. Version 1.0

International Nuclear Information System (INIS)

Ahlfeld, D.P.; Dougherty, D.E.

1994-11-01

MODLP is a computational tool that may help design capture zones for controlling the movement of contaminated groundwater. It creates and solves linear optimization programs that contain constraints on hydraulic head or head differences in a groundwater system. The groundwater domain is represented by USGS MODFLOW groundwater flow simulation model. This document describes the general structure of the computer program, MODLP, the types of constraints that may be imposed, detailed input instructions, interpretation of the output, and the interaction with the MODFLOW simulation kernel

FORMING CHONDRULES IN IMPACT SPLASHES. II. VOLATILE RETENTION

Energy Technology Data Exchange (ETDEWEB)

Dullemond, Cornelis Petrus; Harsono, Daniel; Stammler, Sebastian Markus [Institute for Theoretical Astrophysics, Heidelberg University, Albert-Ueberle-Strasse 2, D-69120 Heidelberg (Germany); Johansen, Anders [Lund Observatory, Department of Astronomy and Theoretical Physics, Lund University, Box 43, SE-22100 Lund (Sweden)

2016-11-20

Solving the mystery of the origin of chondrules is one of the most elusive goals in the field of meteoritics. Recently, the idea of planet(esimal) collisions releasing splashes of lava droplets, long considered out of favor, has been reconsidered as a possible origin of chondrules by several papers. One of the main problems with this idea is the lack of quantitative and simple models that can be used to test this scenario by directly comparing to the many known observables of chondrules. In Paper I of this series, we presented a simple thermal evolution model of a spherically symmetric expanding cloud of molten lava droplets that is assumed to emerge from a collision between two planetesimals. The production of lava could be either because the two planetesimals were already in a largely molten (or almost molten) state due to heating by {sup 26}Al, or due to impact jetting at higher impact velocities. In the present paper, number II of this series, we use this model to calculate whether or not volatile elements such as Na and K will remain abundant in these droplets or whether they will get depleted due to evaporation. The high density of the droplet cloud (e.g., small distance between adjacent droplets) causes the vapor to quickly reach saturation pressure and thus shuts down further evaporation. We show to what extent, and under which conditions, this keeps the abundances of these elements high, as is seen in chondrules. We find that for most parameters of our model (cloud mass, expansion velocity, initial temperature) the volatile elements Mg, Si, and Fe remain entirely in the chondrules. The Na and K abundances inside the droplets will initially stay mostly at their initial values due to the saturation of the vapor pressure, but at some point start to drop due to the cloud expansion. However, as soon as the temperature starts to decrease, most or all of the vapor recondenses again. At the end, the Na and K elements retain most of their initial abundances, albeit

SAFSIM: A computer program for engineering simulations of space reactor system performance

International Nuclear Information System (INIS)

Dobranich, D.

1992-01-01

SAFSIM (System Analysis Flow SIMulator) is a FORTRAN computer program that provides engineering simulations of user-specified flow networks at the system level. It includes fluid mechanics, heat transfer, and reactor dynamics capabilities. SAFSIM provides sufficient versatility to allow the simulation of almost any flow system, from a backyard sprinkler system to a clustered nuclear reactor propulsion system. In addition to versatility, speed and robustness are primary goals of SAFSIM. The current capabilities of SAFSIM are summarized, and some illustrative example results are presented

CHAP: a composite nuclear plant simulation program applied to the 3000 MW(t) HTGR

International Nuclear Information System (INIS)

Secker, P.A.; Bailey, P.G.; Gilbert, J.S.; Willcutt, G.J.E. Jr.; Vigil, J.C.

1977-01-01

The Composite HTGR Analysis Program (CHAP) is a general systems analysis program which has been developed at LASL. The program is being used for simulating large HTGR nuclear power plant operation and accident transients. The general features and analytical methods of the CHAP program are discussed. Features of the large HTGR model and results of model transients are also presented

Simulation of depth distribution of geological strata. HQSW program

International Nuclear Information System (INIS)

Czubek, J.A.; Kolakowski, L.

1987-01-01

The method of simulation of the layered geological formation for a given geological parameter is presented. The geological formation contains at least two types of layers and is given with the depth resolution Δh corresponding to the thickness of the hypothetical elementary layer. Two types of geostatistical distributions of the rock parameters are considered: modified normal and modified lognormal for which the input data are expected value and the variance. The HQSW simulation program given in the paper generates in a random way (but in a given repeatable sequence) the thicknesses of a given type of strata, their average specific radioactivity and the variance of specific radioactivity within a given layer. 8 refs., 14 figs., 1 tab. (author)

Energy consumption program: A computer model simulating energy loads in buildings

Science.gov (United States)

Stoller, F. W.; Lansing, F. L.; Chai, V. W.; Higgins, S.

1978-01-01

The JPL energy consumption computer program developed as a useful tool in the on-going building modification studies in the DSN energy conservation project is described. The program simulates building heating and cooling loads and computes thermal and electric energy consumption and cost. The accuracy of computations are not sacrificed, however, since the results lie within + or - 10 percent margin compared to those read from energy meters. The program is carefully structured to reduce both user's time and running cost by asking minimum information from the user and reducing many internal time-consuming computational loops. Many unique features were added to handle two-level electronics control rooms not found in any other program.

A study on intelligent nuclear systems, (HASP: human acts simulation program)

International Nuclear Information System (INIS)

Asai, Kiyoshi; Uenaka, Junji; Kambayashi, Shaw; Higuchi, Kenji; Kume, Etsuo; Fujisaki, Masahide; Fujii, Minoru; Yokokawa, Mitsuo

1989-03-01

In 1987 Japan Atomic Energy Research Institute has started a ten-years program named HASP, i.e., Human Acts Simulation Program, for artificial intelligence and robotics research. In the HASP, a human-shaped robot reads and understands orders written in natural language, planning and producing a required sequence of actions, accesses to a device or an instrument recognizing its entity and dose the ordered work for plant maintenance. All of these processes including calculation of the radiation exposure of the robot are simulated by logical and numerical computations. The simulated actions of the robot in three-dimensional environments are displayed using a high speed computer for graphics. The aim of the HASP project is threefold, i.e., (1) to develop fundamental technologies for design of intelligent robots, (2) to develop technologies for automated and/or intelligent plants, (3) to provide researchers and engineers in nuclear field with basic and systematized artificial intelligence techniques. The research items are natural language understanding, goal planning by LISP calculus, pattern recognitions by neural network methods, plant modelling by solid modeller, biped robot simulations, graphic display of the robot motion, and a study of design concept of a Monte Carlo vector processor for high speed calculation of the radiation exposure. In this report research results attained in the second year of the HASP project are described. (author)

The program LISE: a simulation of fragment separators

International Nuclear Information System (INIS)

Bazin, D.; Tarasov, O.; Lewitowicz, M.; Sorlin, O.

2001-01-01

The program LISE, which simulates the operation of fragment separators, used in the production of radioactive beams via fragmentation is described. Various aspects of the physical phenomenon involved in the production of such radioactive beams are discussed. They include fragmentation cross sections, energy losses in materials, ionic charge state distributions, as well as ion optics calculations and acceptance effects. Among the goals of this program is a highly user-friendly environment, designed not only to forecast intensities and purities for future experiments, but also as a tuning tool during experiments where its results can be quickly compared to on-line data. In addition, several general purpose tools such as a physical parameters calculator, a database of nuclei properties, and relativistic two-body kinematics calculations make it also attractive in experiments where radioactive beams are not involved. After a general description of fragment separators, the principles underlying the calculations are presented, followed by a practical description of the program and its many features. Finally, a few examples of calculations are compared to on-line data, both qualitatively and quantitatively

Damage to tungsten macro-brush targets under multiple ELM-like heat loads. Experiments vs. numerical simulations and extrapolation to ITER

Energy Technology Data Exchange (ETDEWEB)

Bazylev, B.; Landman, I. [Forschungszentrum Karlsruhe (Germany). IHM; Janeschitz, G. [Forschungszentrum Karlsruhe (DE). Fusion EURATOM] (and others)

2007-07-01

Operation of ITER at high fusion gain is assumed to be the H-mode. A characteristic feature of this regime is the transient release of energy from the confined plasma onto PFCs by multiple ELMs (about 104 ELMs per ITER discharge), which can play a determining role in the erosion rate and lifetime of these components. The expected energy heat loads on the ITER divertor during Type I ELM are in range 0.5-4 MJ/m{sup 2} in timescales of 0.3-0.6 ms. Tungsten macro-brush armour (W-brushes) is foreseen as one of plasma facing components (PFC) for ITER divertor and dome. During the intense transient events in ITER the surface melting, melt motion, melt splashing and evaporation are seen as the main mechanisms of W erosion. The expected erosion of the ITER plasma facing components under transient energy loads can be properly estimated by numerical simulations validated against target erosion of the experiments at the plasma gun facility QSPA-T. Within the collaboration established between EU fusion programme and the Russian Federation, W-brush targets (produced either from pure tungsten or tungsten with 1% of La{sub 2}O{sub 3}) manufactured according to the EU specifications for the ITER divertor targets, have been exposed to multiple ITER ELM-like loads in plasma gun facilities at TRINITI in the range 0.5 - 2.2 MJ/m2 with pulse duration of 0.5 ms. The measured material erosion data have been used to validate the codes MEMOS and PHEMOBRID. Numerical simulations, including 3D-simulations (codes MEMOS and PHEMOBRID), carried out for the conditions of the QSPA-T experiments with heat loads in the range 0.5-2.2 MJ/m{sup 2} and the timescale 0.5 ms demonstrated a rather good agreement with the data obtained at the plasma gun facility QSPA: melting of brush edges at low heat loads, intense melt motion and bridge formation caused by the Rayleigh-Taylor instability at heat loads Q>1.3 MJ/m{sup 2}. The melt splashing generated by the Kelvin-Helmholtz, and Rayleigh

A study on intelligent nuclear systems (HASP: Human Acts Simulation Program)

International Nuclear Information System (INIS)

Asai, Kiyoshi; Fujii, Minoru; Higuchi, Kenji; Kume, Etsuo; Ohtani, Takayuki; Far, B.H.; Kambayashi, Shaw; Akimoto, Masayuki

1991-06-01

The fourth year progress of the Human Acts Simulation Program HASP in short, has been presented in this report. The HASP started in 1987 at JAERI as a ten-year research and development program of underlying technologies for intelligent robots, intelligent nuclear plants and so on. It consists of the research and development of technologies of a knowledge-base system, robot vision, robot kinematics/kinetics, plant geometry database, dose evaluation and high speed Monte Carlo machine. (author)

Lifting simulation of an offshore supply vessel considering various operating conditions

Directory of Open Access Journals (Sweden)

Dong-Hoon Jeong

2016-06-01

Full Text Available Recently, an offshore support vessel is being widely used to install an offshore structure such as a subsea equipment which is laid on its deck. The lifting operation which is one of the installation operations includes lifting off, lifting in the air, splash zone crossing, deep submerging, and finally landing of the structure with an offshore support vessel crane. There are some major considerations during this operation. Especially, when lifting off the structure, if operating conditions such as ocean environmental loads and hoisting (or lowering speed are bad, the excess of tension of wire ropes of the crane and the collision between the offshore support vessel and the structure can be occurred due to the relative motion between them. To solve this problem, this study performs the lifting simulation while the offshore support vessel installs the structure. The simulation includes the calculation of dynamic responses of the offshore support vessel and the equipment, including the wire tension and the collision detection. To check the applicability of the simulation, it is applied to some lifting steps by varying operating conditions. As a result, it is confirmed that the conditions affect the operability of those steps.

Internal Stellar Kinematics of M32 from the SPLASH Survey: Dark Halo Constraints

Science.gov (United States)

Howley, K. M.; Guhathakurta, P.; van der Marel, R.; Geha, M.; Kalirai, J.; Yniguez, B.; Kirby, E.; Cuillandre, J.-C.; Gilbert, K.

2013-03-01

As part of the SPLASH survey of the Andromeda (M31) system, we have obtained Keck/DEIMOS spectra of the compact elliptical (cE) satellite M32. This is the first resolved-star kinematical study of any cE galaxy. In contrast to most previous kinematical studies that extended out to r information to account statistically for M31 contamination. The rotation curve and velocity dispersion profile extend well beyond the radius (r ~ 150'') where the isophotes are distorted. Unlike NGC 205, another close dwarf companion of M31, M32's kinematics appear regular and symmetric and do not show obvious sharp gradients across the region of isophotal elongation and twists. We interpret M31's kinematics using three-integral axisymmetric dynamical equilibrium models constructed using Schwarzschild's orbit superposition technique. Models with a constant mass-to-light ratio can fit the data remarkably well. However, since such a model requires an increasing tangential anisotropy with radius, invoking the presence of an extended dark halo may be more plausible. Such an extended dark halo is definitely required to bind a half-dozen fast-moving stars observed at the largest radii, but these stars may not be an equilibrium component of M32. Data herein were obtained at the W. M. Keck Observatory, which is operated as a scientific partnership among the California Institute of Technology, the University of California, and NASA. The Observatory was made possible by the generous financial support of the W. M. Keck Foundation.

Two-Dimensional Physical and CFD Modelling of Large Gas Bubble Behaviour in Bath Smelting Furnaces

Directory of Open Access Journals (Sweden)

Yuhua Pan

2010-09-01

Full Text Available The behaviour of large gas bubbles in a liquid bath and the mechanisms of splash generation due to gas bubble rupture in high-intensity bath smelting furnaces were investigated by means of physical and mathematical (CFD modelling techniques. In the physical modelling work, a two-dimensional Perspex model of the pilot plant furnace at CSIRO Process Science and Engineering was established in the laboratory. An aqueous glycerol solution was used to simulate liquid slag. Air was injected via a submerged lance into the liquid bath and the bubble behaviour and the resultant splashing phenomena were observed and recorded with a high-speed video camera. In the mathematical modelling work, a two-dimensional CFD model was developed to simulate the free surface flows due to motion and deformation of large gas bubbles in the liquid bath and rupture of the bubbles at the bath free surface. It was concluded from these modelling investigations that the splashes generated in high-intensity bath smelting furnaces are mainly caused by the rupture of fast rising large gas bubbles. The acceleration of the bubbles into the preceding bubbles and the rupture of the coalescent bubbles at the bath surface contribute significantly to splash generation.

IRFK2D: a computer program for simulating intrinsic random functions of order k

Science.gov (United States)

Pardo-Igúzquiza, Eulogio; Dowd, Peter A.

2003-07-01

IRFK2D is an ANSI Fortran-77 program that generates realizations of an intrinsic function of order k (with k equal to 0, 1 or 2) with a permissible polynomial generalized covariance model. The realizations may be non-conditional or conditioned to the experimental data. The turning bands method is used to generate realizations in 2D and 3D from simulations of an intrinsic random function of order k along lines that span the 2D or 3D space. The program generates two output files, the first containing the simulated values and the second containing the theoretical generalized variogram for different directions together with the theoretical model. The experimental variogram is calculated from the simulated values while the theoretical variogram is the specified generalized covariance model. The generalized variogram is used to assess the quality of the simulation as measured by the extent to which the generalized covariance is reproduced by the simulation. The examples given in this paper indicate that IRFK2D is an efficient implementation of the methodology.

ACCSIM - a program to simulate the accumulation of intense proton beams

International Nuclear Information System (INIS)

Jones, F.W.; MacKenzie, G.H.; Schoenauer, H.

1989-09-01

ACCSIM is a multiparticle 3-D tracking code initially written to simulate multiturn injection. It treats simultaneously, but to a certain degree of approximation, transverse and longitudinal space charge forces, lattice perturbations simulated by thin multipoles, and energy loss, Coulomb and nuclear scattering in charge exchange foils or internal targets. Output includes particle distributions in phase space and real space, loss statistics and figures of merit for the retained ensemble. The program is described in detail and examples given of its use for existing and proposed machines

A computer program for estimating the power-density spectrum of advanced continuous simulation language generated time histories

Science.gov (United States)

Dunn, H. J.

1981-01-01

A computer program for performing frequency analysis of time history data is presented. The program uses circular convolution and the fast Fourier transform to calculate power density spectrum (PDS) of time history data. The program interfaces with the advanced continuous simulation language (ACSL) so that a frequency analysis may be performed on ACSL generated simulation variables. An example of the calculation of the PDS of a Van de Pol oscillator is presented.

Design and Analysis of Solar Smartflower Simulation by Solidwork Program

Science.gov (United States)

Mulyana, Tatang; Sebayang, Darwin; Fajrina, Fildzah; Raihan; Faizal, M.

2018-03-01

The potential of solar energy that is so large in Indonesia can be a driving force for the use of renewable energy as a solution for energy needs. Government with the community can utilize and optimize this technology to increase the electrification ratio up to 100% in all corners of Indonesia. Because of its modular and practical nature, making this technology easy to apply. One of the latest imported products that have started to be offered and sold in Indonesia but not yet widely used for solar power generation is the kind of smartflower. Before using the product, it is of course very important and immediately to undertake an in-depth study of the utilization, use, maintenance, repair, component supply and fabrication. The best way to know the above is through a review of the design and simulation. To meet this need, this paper presents a solar-smartflower design and then simulated using the facilities available in the solidwork program. Solid simulation express is a tool that serves to create power simulation of a design part modelling. With the simulation is very helpful at all to reduce errors in making design. Accurate or not a design created is also influenced by several other factors such as material objects, the silent part of the part, and the load given. The simulation is static simulation and body battery drop test, and based on the results of this simulation is known that the design results have been very satisfactory.

ARTICLES: Thermohydrodynamic models of the interaction of pulse-periodic radiation with matter

Science.gov (United States)

Arutyunyan, R. V.; Baranov, V. Yu; Bol'shov, Leonid A.; Malyuta, D. D.; Mezhevov, V. S.; Pis'mennyĭ, V. D.

1987-02-01

Experimental and theoretical investigations were made of the processes of drilling and deep melting of metals by pulsed and pulse-periodic laser radiation. Direct photography of the surface revealed molten metal splashing due to interaction with single CO2 laser pulses. A proposed thermohydrodynamic model was used to account for the experimental results and to calculate the optimal parameters of pulse-periodic radiation needed for deep melting. The melt splashing processes were simulated numerically.

Use of Immersive Simulations to Enhance Graduate Student Learning: Implications for Educational Leadership Programs

Science.gov (United States)

Voelkel, Robert H.; Johnson, Christie W.; Gilbert, Kristen A.

2016-01-01

The purpose of this article is to present how one university incorporates immersive simulations through platforms which employ avatars to enhance graduate student understanding and learning in educational leadership programs. While using simulations and immersive virtual environments continues to grow, the literature suggests limited evidence of…

The Effectiveness of Simulated Robots for Supporting the Learning of Introductory Programming: A Multi-Case Case Study

Science.gov (United States)

Major, Louis; Kyriacou, Theocharis; Brereton, Pearl

2014-01-01

This work investigates the effectiveness of simulated robots as tools to support the learning of programming. After the completion of a systematic review and exploratory research, a multi-case case study was undertaken. A simulator, named Kebot, was developed and used to run four 10-hour programming workshops. Twenty-three student participants…

Automatic generation of Fortran programs for algebraic simulation models

International Nuclear Information System (INIS)

Schopf, W.; Rexer, G.; Ruehle, R.

1978-04-01

This report documents a generator program by which econometric simulation models formulated in an application-orientated language can be transformed automatically in a Fortran program. Thus the model designer is able to build up, test and modify models without the need of a Fortran programmer. The development of a computer model is therefore simplified and shortened appreciably; in chapter 1-3 of this report all rules are presented for the application of the generator to the model design. Algebraic models including exogeneous and endogeneous time series variables, lead and lag function can be generated. In addition, to these language elements, Fortran sequences can be applied to the formulation of models in the case of complex model interrelations. Automatically the generated model is a module of the program system RSYST III and is therefore able to exchange input and output data with the central data bank of the system and in connection with the method library modules can be used to handle planning problems. (orig.) [de

GITTAM program for numerical simulation of one-dimensional targets TIS. Part 2

International Nuclear Information System (INIS)

Arpishkin, Yu.P.; Basko, M.M.; Sokolovskij, M.V.

1989-01-01

A finite-difference algorithm for numeric solution of a system of one-dimensional hydrodynamics equation with heat conductivity, radiation diffusion and thermonuclear combustion is considered. The algorithm presented allows one to simulate one-dimensional thermonuclear targets for heavy-ion synthesis (HIS), irradiated with heavy ion beams. A brief description of a complex of GITTAM programs in which finite-difference algorithm for one-dimensional thermonuclear HIS target simulation is used, is given. 5 refs.; 3 figs

Development and applications of Super Monte Carlo Simulation Program for Advanced Nuclear Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Wu, Y., E-mail: yican.wu@fds.org.cn [Inst. of Nuclear Energy Safety Technology, Hefei, Anhui (China)

2015-07-01

'Full text:' Super Monte Carlo Simulation Program for Advanced Nuclear Energy Systems (SuperMC) is a CAD-based Monte Carlo (MC) program for integrated simulation of nuclear system by making use of hybrid MC-deterministic method and advanced computer technologies. The main usability features are automatic modeling of geometry and physics, visualization and virtual simulation and cloud computing service. SuperMC 2.3, the latest version, can perform coupled neutron and photon transport calculation. SuperMC has been verified by more than 2000 benchmark models and experiments, and has been applied in tens of major nuclear projects, such as the nuclear design and analysis of International Thermonuclear Experimental Reactor (ITER) and China Lead-based reactor (CLEAR). Development and applications of SuperMC are introduced in this presentation. (author)

Development and applications of Super Monte Carlo Simulation Program for Advanced Nuclear Energy Systems

International Nuclear Information System (INIS)

Wu, Y.

2015-01-01

'Full text:' Super Monte Carlo Simulation Program for Advanced Nuclear Energy Systems (SuperMC) is a CAD-based Monte Carlo (MC) program for integrated simulation of nuclear system by making use of hybrid MC-deterministic method and advanced computer technologies. The main usability features are automatic modeling of geometry and physics, visualization and virtual simulation and cloud computing service. SuperMC 2.3, the latest version, can perform coupled neutron and photon transport calculation. SuperMC has been verified by more than 2000 benchmark models and experiments, and has been applied in tens of major nuclear projects, such as the nuclear design and analysis of International Thermonuclear Experimental Reactor (ITER) and China Lead-based reactor (CLEAR). Development and applications of SuperMC are introduced in this presentation. (author)

OpenDx programs for visualization of computational fluid dynamics (CFD) simulations

International Nuclear Information System (INIS)

Silva, Marcelo Mariano da

2008-01-01

The search for high performance and low cost hardware and software solutions always guides the developments performed at the IEN parallel computing laboratory. In this context, this dissertation about the building of programs for visualization of computational fluid dynamics (CFD) simulations using the open source software OpenDx was written. The programs developed are useful to produce videos and images in two or three dimensions. They are interactive, easily to use and were designed to serve fluid dynamics researchers. A detailed description about how this programs were developed and the complete instructions of how to use them was done. The use of OpenDx as development tool is also introduced. There are examples that help the reader to understand how programs can be useful for many applications. (author)

Generalized Fluid System Simulation Program (GFSSP) - Version 6

Science.gov (United States)

Majumdar, Alok; LeClair, Andre; Moore, Ric; Schallhorn, Paul

2015-01-01

The Generalized Fluid System Simulation Program (GFSSP) is a finite-volume based general-purpose computer program for analyzing steady state and time-dependent flow rates, pressures, temperatures, and concentrations in a complex flow network. The program is capable of modeling real fluids with phase changes, compressibility, mixture thermodynamics, conjugate heat transfer between solid and fluid, fluid transients, pumps, compressors, flow control valves and external body forces such as gravity and centrifugal. The thermo-fluid system to be analyzed is discretized into nodes, branches, and conductors. The scalar properties such as pressure, temperature, and concentrations are calculated at nodes. Mass flow rates and heat transfer rates are computed in branches and conductors. The graphical user interface allows users to build their models using the 'point, drag, and click' method; the users can also run their models and post-process the results in the same environment. The integrated fluid library supplies thermodynamic and thermo-physical properties of 36 fluids, and 24 different resistance/source options are provided for modeling momentum sources or sinks in the branches. Users can introduce new physics, non-linear and time-dependent boundary conditions through user-subroutine.

Nuclear Engine System Simulation (NESS). Volume 1: Program user's guide. Final Report

International Nuclear Information System (INIS)

Pelaccio, D.G.; Scheil, C.M.; Petrosky, L.J.

1993-03-01

A Nuclear Thermal Propulsion (NTP) engine system design analysis tool is required to support current and future Space Exploration Initiative (SEI) propulsion and vehicle design studies. Currently available NTP engine design models are those developed during the NERVA program in the 1960's and early 1970's and are highly unique to that design or are modifications of current liquid propulsion system design models. To date, NTP engine-based liquid design models lack integrated design of key NTP engine design features in the areas of reactor, shielding, multi-propellant capability, and multi-redundant pump feed fuel systems. Additionally, since the SEI effort is in the initial development stage, a robust, verified NTP analysis design tool could be of great use to the community. This effort developed an NTP engine system design analysis program (tool), known as the Nuclear Engine System Simulation (NESS) program, to support ongoing and future engine system and stage design study efforts. In this effort, Science Applications International Corporation's (SAIC) NTP version of the Expanded Liquid Engine Simulation (ELES) program was modified extensively to include Westinghouse Electric Corporation's near-term solid-core reactor design model. The ELES program has extensive capability to conduct preliminary system design analysis of liquid rocket systems and vehicles. The program is modular in nature and is versatile in terms of modeling state-of-the-art component and system options as discussed. The Westinghouse reactor design model, which was integrated in the NESS program, is based on the near-term solid-core ENABLER NTP reactor design concept. This program is now capable of accurately modeling (characterizing) a complete near-term solid-core NTP engine system in great detail, for a number of design options, in an efficient manner

Development of the PARA-ID Program to Simulate a Unified Viscoplasticity Behaviour

International Nuclear Information System (INIS)

Koo, Gyeong Hoi

2009-01-01

The PARA-ID code is a general purpose computer simulation program for a nonlinear cyclic material behavior with and without viscous effects, which can simulate various constitutive models such as - Prager Model - Armstrong and Frederick Model - Chaboche 3-decomposed rule Model - Chaboche 4-decomposed rule Model - Ohno and Wang Model - Unified Chaboche Viscoplastic Model In this paper, the unified Chaboche viscoplasticity model is investigated with some examples of application for a cyclic hardening material of 316L

A Novel Approach for Modeling Chemical Reaction in Generalized Fluid System Simulation Program

Science.gov (United States)

Sozen, Mehmet; Majumdar, Alok

2002-01-01

The Generalized Fluid System Simulation Program (GFSSP) is a computer code developed at NASA Marshall Space Flight Center for analyzing steady state and transient flow rates, pressures, temperatures, and concentrations in a complex flow network. The code, which performs system level simulation, can handle compressible and incompressible flows as well as phase change and mixture thermodynamics. Thermodynamic and thermophysical property programs, GASP, WASP and GASPAK provide the necessary data for fluids such as helium, methane, neon, nitrogen, carbon monoxide, oxygen, argon, carbon dioxide, fluorine, hydrogen, water, a hydrogen, isobutane, butane, deuterium, ethane, ethylene, hydrogen sulfide, krypton, propane, xenon, several refrigerants, nitrogen trifluoride and ammonia. The program which was developed out of need for an easy to use system level simulation tool for complex flow networks, has been used for the following purposes to name a few: Space Shuttle Main Engine (SSME) High Pressure Oxidizer Turbopump Secondary Flow Circuits, Axial Thrust Balance of the Fastrac Engine Turbopump, Pressurized Propellant Feed System for the Propulsion Test Article at Stennis Space Center, X-34 Main Propulsion System, X-33 Reaction Control System and Thermal Protection System, and International Space Station Environmental Control and Life Support System design. There has been an increasing demand for implementing a combustion simulation capability into GFSSP in order to increase its system level simulation capability of a liquid rocket propulsion system starting from the propellant tanks up to the thruster nozzle for spacecraft as well as launch vehicles. The present work was undertaken for addressing this need. The chemical equilibrium equations derived from the second law of thermodynamics and the energy conservation equation derived from the first law of thermodynamics are solved simultaneously by a Newton-Raphson method. The numerical scheme was implemented as a User

BRAND program complex for neutron-physical experiment simulation by the Monte-Carlo method

International Nuclear Information System (INIS)

Androsenko, A.A.; Androsenko, P.A.

1984-01-01

Possibilities of the BRAND program complex for neutron and γ-radiation transport simulation by the Monte-Carlo method are described in short. The complex includes the following modules: geometric module, source module, detector module, modules of simulation of a vector of particle motion direction after interaction and a free path. The complex is written in the FORTRAN langauage and realized by the BESM-6 computer

Present status of an integrated software system for HASP (Human Acts Simulation Program)

International Nuclear Information System (INIS)

Otani, Takayuki; Ebihara, Ken-ichi; Kambayashi, Shaw; Kume, Etsuo; Higuchi, Kenji; Fujii, Minoru; Akimoto, Masayuki

1994-01-01

In Human Acts Simulation Program (HASP), human acts to be realized by a human-shaped intelligent robot in a nuclear power plant are simulated by computers. The major purpose of HASP is to develop basic and underlying design technologies for intelligent and automatic power plant. The objectives of this paper is to show the present status of the HASP, with particular emphasis on activities targetted at the integration of developed subsystems to simulate the important capabilities of the intelligent robot such as planning, robot dynamics, and so on. (author)

EVALUATION OF ENERGY PERFORMANCE USING DOE-2 ENERGY SIMULATION PROGRAM IN SINGAPORE

Directory of Open Access Journals (Sweden)

Po Seng Kian

2000-01-01

Full Text Available Recently, due to worldwide energy cost rising significantly, there has been an essential need to minimize the energy consumption. This global warning address many countries including Singapore realizing the important of energy efficiency in industries and buildings. This paper deals with analyzing the energy consumption of an 11-storey commercial building in Singapore using DOE-2 Energy Simulation Program. A study is made on the benefits derived from modifying the building envelope, space system setting, air-conditioning plant, and lighting. This encompasses a description of its quantitative impact on cooling load, energy consumption and energy saving achieved as compared with the original building. Following this, a life cycle costing is done to determine the economic benefits attained from this modification. This study shows that some alternative solutions can be achieved using energy simulation program to conserve the energy consumption.

TOURGHREACT: A Simulation Program for Non-isothermal Multiphase Reactive Geochemical Transport in Variably Saturated Geologic Media

OpenAIRE

Xu, Tianfu; Sonnenthal, Eric; Spycher, Nicolas; Pruess, Karsten

2004-01-01

TOUGHREACT is a numerical simulation program for chemically reactive non-isothermal flows of multiphase fluids in porous and fractured media. The program was written in Fortran 77 and developed by introducing reactive geochemistry into the multiphase fluid and heat flow simulator TOUGH2. A variety of subsurface thermo-physical-chemical processes are considered under a wide range of conditions of pressure, temperature, water saturation, ionic strength, and pH and Eh. Interactions between ...

Implementing a Cardiac Skills Orientation and Simulation Program.

Science.gov (United States)

Hemingway, Maureen W; Osgood, Patrice; Mannion, Mildred

2018-02-01

Patients with cardiac morbidities admitted for cardiac surgical procedures require perioperative nurses with a high level of complex nursing skills. Orienting new cardiac team members takes commitment and perseverance in light of variable staffing levels, high-acuity patient populations, an active cardiac surgical schedule, and the unpredictability of scheduling patients undergoing cardiac transplantation. At an academic medical center in Boston, these issues presented opportunities to orient new staff members to the scrub person role, but hampered efforts to provide active learning opportunities in a safe environment. As a result, facility personnel created a program to increase new staff members' skills, confidence, and proficiency, while also increasing the number of staff members who were proficient at scrubbing complex cardiac procedures. To address the safe learning requirement, personnel designed a simulation program to provide scrubbing experience, decrease orientees' supervision time, and increase staff members' confidence in performing the scrub person role. © AORN, Inc, 2018.

'Transitorion' program for the simulation of the liquid zone evolution against power transients

International Nuclear Information System (INIS)

Coutsiers, Ernesto; Rabiti, Arnaldo; Pomerantz, Marcelo E.; Villar, Javier

2003-01-01

This work presents a program that allows to simulate the liquid zones evolution against power transients at Embalse nuclear power plant reactor. This program takes into account the dynamic effects of plutonium, samarium, xenon and iodine. It simulates also fuel burning, coolant void and the behavior of the reactor regulating system. The validation, based in the comparison with plant's real cases, gives a maximum error of 7% in liquid zone's average in periods of around 5 days. However, the typical adjustment has a lower error, around 2% in liquid zone's average. As the main conclusions of this work the good adjustment of the results of the code as well as the building of an important economic tool for the power plant could be highlighted. (author )

Development of a simulation program to study error propagation in the reprocessing input accountancy measurements

International Nuclear Information System (INIS)

Sanfilippo, L.

1987-01-01

A physical model and a computer program have been developed to simulate all the measurement operations involved with the Isotopic Dilution Analysis technique currently applied in the Volume - Concentration method for the Reprocessing Input Accountancy, together with their errors or uncertainties. The simulator is apt to easily solve a number of problems related to the measurement sctivities of the plant operator and the inspector. The program, written in Fortran 77, is based on a particular Montecarlo technique named ''Random Sampling''; a full description of the code is reported

Electron microprobe analysis (WDS EPMA) of Zhamanshin glass reveals the impactor and a common role of accretion in the origin of splash-form impact glass

International Nuclear Information System (INIS)

Vetvicka, I; Frank, J; Drtina, J

2010-01-01

Impact glass samples collected during expeditions to the Zhamashin and Lonar craters were subjected to a morphology survey and compared to Wabar, Henbury and Darwin impact glasses to reveal that the accretion of fibres and spherules is not exclusive for irghizites but occurs in other splash form glasses over the world. WDS EPMA and LA-ICP-MS assays of Zhamanshin and Lonar glasses enabled the definition of akmurynites as Zhamanshin glass of specific morphology, chemistry and absence of extraterrestrial contamination. However, extraterrestrial contamination in irghizites was verified and further WDS EPMA analyses led to the conclusion that the Zhamanshin crater had been formed by the impact of a primitive achondrite of Lodran chemistry.

Development of user interface to support automatic program generation of nuclear power plant analysis by module-based simulation system

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Mizutani, Naoki; Nakaya, Ken-ichiro; Wakabayashi, Jiro

1988-01-01

Module-based Simulation System (MSS) has been developed to realize a new software work environment enabling versatile dynamic simulation of a complex nuclear power system flexibly. The MSS makes full use of modern software technology to replace a large fraction of human software works in complex, large-scale program development by computer automation. Fundamental methods utilized in MSS and developmental study on human interface system SESS-1 to help users in generating integrated simulation programs automatically are summarized as follows: (1) To enhance usability and 'communality' of program resources, the basic mathematical models of common usage in nuclear power plant analysis are programed as 'modules' and stored in a module library. The information on usage of individual modules are stored in module database with easy registration, update and retrieval by the interactive management system. (2) Target simulation programs and the input/output files are automatically generated with simple block-wise languages by a precompiler system for module integration purpose. (3) Working time for program development and analysis in an example study of an LMFBR plant thermal-hydraulic transient analysis was demonstrated to be remarkably shortened, with the introduction of an interface system SESS-1 developed as an automatic program generation environment. (author)

MuSim, a Graphical User Interface for Multiple Simulation Programs

Energy Technology Data Exchange (ETDEWEB)

Roberts, Thomas [MUONS Inc., Batavia; Cummings, Mary Anne [MUONS Inc., Batavia; Johnson, Rolland [MUONS Inc., Batavia; Neuffer, David [Fermilab

2016-06-01

MuSim is a new user-friendly program designed to interface to many different particle simulation codes, regardless of their data formats or geometry descriptions. It presents the user with a compelling graphical user interface that includes a flexible 3-D view of the simulated world plus powerful editing and drag-and-drop capabilities. All aspects of the design can be parametrized so that parameter scans and optimizations are easy. It is simple to create plots and display events in the 3-D viewer (with a slider to vary the transparency of solids), allowing for an effortless comparison of different simulation codes. Simulation codes: G4beamline, MAD-X, and MCNP; more coming. Many accelerator design tools and beam optics codes were written long ago, with primitive user interfaces by today's standards. MuSim is specifically designed to make it easy to interface to such codes, providing a common user experience for all, and permitting the construction and exploration of models with very little overhead. For today's technology-driven students, graphical interfaces meet their expectations far better than text-based tools, and education in accelerator physics is one of our primary goals.

A Simulation-Based Program to Train Medical Residents to Lead and Perform Advanced Cardiovascular Life Support

Science.gov (United States)

Stefan, Mihaela S.; Belforti, Raquel K.; Langlois, Gerard; Rothberg, Michael B.

2014-01-01

Background Medical residents are often responsible for leading and performing cardiopulmonary resuscitation; however, their levels of expertise and comfort as leaders of advanced cardiovascular life support (ACLS) teams vary widely. While the current American Heart Association ACLS course provides education in recommended resuscitative protocols, training in leadership skills is insufficient. In this article, we describe the design and implementation in our institution of a formative curriculum aimed at improving residents’ readiness for being leaders of ACLS teams using human patient simulation. Human patient simulation refers to a variety of technologies using mannequins with realistic features, which allows learners to practice through scenarios without putting patients at risk. We discuss the limitations of the program and the challenges encountered in implementation. We also provide a description of the initiation and organization of the program. Case scenarios and assessment tools are provided. Description of the Institutional Training Program Our simulation-based training curriculum consists of 8 simulated patient scenarios during four 1-hour sessions. Postgraduate year–2 and 3 internal medicine residents participate in this program in teams of 4. Assessment tools are utilized only for formative evaluation. Debriefing is used as a teaching strategy for the individual resident leader of the ACLS team to facilitate learning and improve performance. To evaluate the impact of the curriculum, we administered a survey before and after the intervention. The survey consisted of 10 questions answered on a 5-point Likert scale, which addressed residents’ confidence in leading ACLS teams, management of the equipment, and management of cardiac rhythms. Respondents’ mean presimulation (ie, baseline) and postsimulation (outcome) scores were compared using a 2-sample t test. Residents’ overall confidence score improved from 2.8 to 3.9 (P simulation-based training

SOLVEX: a computer program for simulation of solvent extraction processes

International Nuclear Information System (INIS)

Scotten, W.C.

1975-09-01

SOLVEX is a FORTRAN IV computer program that simulates the dynamic behavior of solvent extraction processes conducted in mixer-settlers and centrifugal contactors. Two options permit terminating dynamic phases by time or by achieving steady state, and a third option permits artificial rapid close to steady state. Thus the program is well suited to multiple phases of dynamic problems and multiple input of steady state problems. Changes from the previous problem are the only inputs required for each succeeding problem. Distribution data can be supplied by two-variable third-power polynomial equations or by three-variable tables in any one of 16 different combinations involving phase concentrations or distribution coefficients (ratio of phase concentrations) or their logarithms

A PC-based computer program for simulation of containment pressurization

International Nuclear Information System (INIS)

Seifaee, F.

1990-01-01

This paper reports that a PC-based computer program has been developed to simulate a pressurized water reactor (PWR) containment during various transients. This containment model is capable of determining pressure and temperature history of a PWR containment in the event of a loss of coolant accident, as well as main steam line breaks inside the containment. Conservation of mass and energy equations are applied to the containment model. Development of the program is based on minimization of input specified information and user friendliness. Maximization of calculation efficiency is obtained by superseding the traditional trial and error procedure for determination of the state variables and implementation of an explicit solution for pressure. The program includes simplified models for active heat removal systems. The results are in close agreement between the present model and CONTEMPT-MOD5 computer code for pressure and temperature inside the containment

BWR-plant simulator and its neural network companion with programming under mat lab environment

International Nuclear Information System (INIS)

Ghenniwa, Fatma Suleiman

2008-01-01

Stand alone nuclear power plant simulators, as well as building blocks based nuclear power simulator are available from different companies throughout the world. In this work, a review of such simulators has been explored for both types. Also a survey of the possible authoring tools for such simulators development has been performed. It is decided, in this research, to develop prototype simulator based on components building blocks. Further more, the authoring tool (Mat lab software) has been selected for programming. It has all the basic tools required for the simulator development similar to that developed by specialized companies for simulator like MMS, APROS and others. Components simulations, as well as integrated components for power plant simulation have been demonstrated. Preliminary neural network reactor model as part of a prepared neural network modules library has been used to demonstrate module order shuffling during simulation. The developed components library can be refined and extended for further development. (author)

Heat simulation via Scilab programming

Science.gov (United States)

Hasan, Mohammad Khatim; Sulaiman, Jumat; Karim, Samsul Arifin Abdul

2014-07-01

This paper discussed the used of an open source sofware called Scilab to develop a heat simulator. In this paper, heat equation was used to simulate heat behavior in an object. The simulator was developed using finite difference method. Numerical experiment output show that Scilab can produce a good heat behavior simulation with marvellous visual output with only developing simple computer code.

GITTAM program for numerical simulation of one-dimensional targets TIS. Part 3

International Nuclear Information System (INIS)

Basko, M.M.; Sokolovskij, M.V.

1989-01-01

Results of testing calculations according to GITTAM program, developed for numeric simulation of one-dimensional thermonuclear targets of heavy-ion synthesis are presented. Finite-difference method for solving a system of one-dimensional hydrodynamics equations with heat conductivity, radiation diffusion and thermonuclear combustion is used in the GITTAM program. In the tests presented, based on simple automodel solutions, adiabatic motion as well as distribution of shock, thermal and radial waves in gas with simple polytron state equation is investigated. 3 refs.; 6 figs

Development of a fast running accident analysis computer program for use in a simulator

International Nuclear Information System (INIS)

Cacciabue, P.C.

1985-01-01

This paper describes how a reactor safety nuclear computer program can be modified and improved with the aim of reaching a very fast running tool to be used as a physical model in a plant simulator, without penalizing the accuracy of results. It also discusses some ideas on how the physical theoretical model can be combined to a driving statistical tool for the build up of the entire package of software to be implemented in the simulator for risk and reliability analysis. The approach to the problem, although applied to a specific computer program, can be considered quite general if an already existing and well tested code is being used for the purpose. The computer program considered is ALMOD, originally developed for the analysis of the thermohydraulic and neutronic behaviour of the reactor core, primary circuit and steam generator during operational and special transients. (author)

PHAST--a program for simulating ground-water flow, solute transport, and multicomponent geochemical reactions

Science.gov (United States)

Parkhurst, David L.; Kipp, Kenneth L.; Engesgaard, Peter; Charlton, Scott R.

2004-01-01

The computer program PHAST simulates multi-component, reactive solute transport in three-dimensional saturated ground-water flow systems. PHAST is a versatile ground-water flow and solute-transport simulator with capabilities to model a wide range of equilibrium and kinetic geochemical reactions. The flow and transport calculations are based on a modified version of HST3D that is restricted to constant fluid density and constant temperature. The geochemical reactions are simulated with the geochemical model PHREEQC, which is embedded in PHAST. PHAST is applicable to the study of natural and contaminated ground-water systems at a variety of scales ranging from laboratory experiments to local and regional field scales. PHAST can be used in studies of migration of nutrients, inorganic and organic contaminants, and radionuclides; in projects such as aquifer storage and recovery or engineered remediation; and in investigations of the natural rock-water interactions in aquifers. PHAST is not appropriate for unsaturated-zone flow, multiphase flow, density-dependent flow, or waters with high ionic strengths. A variety of boundary conditions are available in PHAST to simulate flow and transport, including specified-head, flux, and leaky conditions, as well as the special cases of rivers and wells. Chemical reactions in PHAST include (1) homogeneous equilibria using an ion-association thermodynamic model; (2) heterogeneous equilibria between the aqueous solution and minerals, gases, surface complexation sites, ion exchange sites, and solid solutions; and (3) kinetic reactions with rates that are a function of solution composition. The aqueous model (elements, chemical reactions, and equilibrium constants), minerals, gases, exchangers, surfaces, and rate expressions may be defined or modified by the user. A number of options are available to save results of simulations to output files. The data may be saved in three formats: a format suitable for viewing with a text editor; a

Evaluation of Teaching the IS-LM Model through a Simulation Program

Science.gov (United States)

Pablo-Romero, Maria del Populo; Pozo-Barajas, Rafael; Gomez-Calero, Maria de la Palma

2012-01-01

The IS-ML model is a basic tool used in the teaching of short-term macroeconomics. Teaching is essentially done through the use of graphs. However, the way these graphs are traditionally taught does not allow the learner to easily visualise changes in the curves. The IS-LM simulation program overcomes difficulties encountered in understanding the…

Simulation of the space-time evolution of color-flux tubes (guidelines to the TERMITE program)

International Nuclear Information System (INIS)

Dyrek, A.

1990-08-01

We give the description of the computer program which simulates boost-invariant evolution of color-flux tubes in high-energy processes. The program provides a graphic demonstration of space-time trajectories of created particles and can also be used as Monte-Carlo generator of events. (author)

A Simulation Tool for tccp Programs

Directory of Open Access Journals (Sweden)

María-del-Mar Gallardo

2017-01-01

Full Text Available The Timed Concurrent Constraint Language tccp is a declarative synchronous concurrent language, particularly suitable for modelling reactive systems. In tccp, agents communicate and synchronise through a global constraint store. It supports a notion of discrete time that allows all non-blocked agents to proceed with their execution simultaneously. In this paper, we present a modular architecture for the simulation of tccp programs. The tool comprises three main components. First, a set of basic abstract instructions able to model the tccp agent behaviour, the memory model needed to manage the active agents and the state of the store during the execution. Second, the agent interpreter that executes the instructions of the current agent iteratively and calculates the new agents to be executed at the next time instant. Finally, the constraint solver components which are the modules that deal with constraints. In this paper, we describe the implementation of these components and present an example of a real system modelled in tccp.

Development of support tools for efficient construction of dynamic simulation program for engineering systems

International Nuclear Information System (INIS)

Gofuku, Akio

1993-01-01

In this study, two support tools are developed for construction of a dynamic simulation program for engineering systems (especially nuclear systems) by combining software modules. These are (1) a sub-system to support the module selection suitable for dynamic simulation and (2) a graphical user interface to support visual construction of simulation programs. The support tools are designed to be independent on the conception of software modules (data communication methods between modules). In the module selection sub-system of item 1, a module is characterized beforehand by keywords for several criteria. The similarity between the characteristic of requested module by users and that of registered modules in the module library is estimated by a weighted average of similarity indexes for criteria. In the module selection sub-system, the weights are flexibly extracted from users by applying the analytic hierarchy process. The graphical user interface helps users to specify both calling order of modules and data transfer between two modules. The availability of the support tools is evaluated by several sample problems of module selection and dynamic simulation model construction. The support tools will be a strong tool for the efficient usage of software modules. (author)

BWR Full Integral Simulation Test (FIST) program: facility description report

International Nuclear Information System (INIS)

Stephens, A.G.

1984-09-01

A new boiling water reactor safety test facility (FIST, Full Integral Simulation Test) is described. It will be used to investigate small breaks and operational transients and to tie results from such tests to earlier large-break test results determined in the TLTA. The new facility's full height and prototypical components constitute a major scaling improvement over earlier test facilities. A heated feedwater system, permitting steady-state operation, and a large increase in the number of measurements are other significant improvements. The program background is outlined and program objectives defined. The design basis is presented together with a detailed, complete description of the facility and measurements to be made. An extensive component scaling analysis and prediction of performance are presented

A Dynamic Simulation Program for a Hydriodic Acid Concentration and Decomposition Process in the VHTR-SI Process

International Nuclear Information System (INIS)

Chang, Ji Woon; Shin, Young Joon; Lee, Tae Hoon; Lee, Ki Young; Kim, Yong Wan; Chang, Jong Hwa; Youn, Cheung

2011-01-01

The Sulfur-Iodine (SI) cycle which can produce hydrogen by using nuclear heat consists of a Bunsen reaction (Section 1), a sulfur acid concentration and decomposition (Section 2), and a hydriodic acid concentration and decomposition (Section 3). The heat required in the SI process can be supplied through an intermediate heat exchanger (IHX) by a Very High Temperature Gas Cooled Reactor (VHTR). The Korea Atomic Energy Research Institute-Dynamic Simulation Code (KAERI-DySCo) based on the Visual C++ is an integration application software that simulates the dynamic behavior of the SI process. KAERI-DySCo was prepared to solve dynamic problem of the seven chemical reactors which consist of Sections 2 and 3. Section 3 is the key part of the SI process, because the strong non-ideality and the partial immiscibility of the binary HI.H 2 O and the ternary HI.I 2 .H 2 O (HIX solution) mixture make it difficult to model and simulate the dynamic behavior of the system. Therefore, it is necessary to compose separately a dynamic simulation program for Section 3 in KAERI-DySCo optimization. In this paper, a simulation program to analyze the dynamic behavior of Section 3 is introduced using the prepared KAERI-DySCo, and results of dynamic simulation are represented by running the program

Research use of the AIDA www.2aida.org diabetes software simulation program: a review--part 2. Generating simulated blood glucose data for prototype validation.

Science.gov (United States)

Lehmann, Eldon D

2003-01-01

The purpose of this review is to describe research applications of the AIDA diabetes software simulator. AIDA is a computer program that permits the interactive simulation of insulin and glucose profiles for teaching, demonstration, and self-learning purposes. Since March/April 1996 it has been made freely available on the Internet as a noncommercial contribution to continuing diabetes education. Up to May 2003 well over 320,000 visits have been logged at the main AIDA Website--www.2aida.org--and over 65,000 copies of the AIDA program have been downloaded free-of-charge. This review (the second of two parts) overviews research projects and ventures, undertaken for the most part by other research workers in the diabetes computing field, that have made use of the freeware AIDA program. As with Part 1 of the review (Diabetes Technol Ther 2003;5:425-438) relevant research work was identified in three main ways: (i) by personal (e-mail/written) communications from researchers, (ii) via the ISI Web of Science citation database to identify published articles which referred to AIDA-related papers, and (iii) via searches on the Internet. Also, in a number of cases research students who had sought advice about AIDA, and diabetes computing in general, provided copies of their research dissertations/theses upon the completion of their projects. Part 2 of this review highlights some more of the research projects that have made use of the AIDA diabetes simulation program to date. A wide variety of diabetes computing topics are addressed. These range from learning about parameter interactions using simulated blood glucose data, to considerations of dietary assessments, developing new diabetes models, and performance monitoring of closed-loop insulin delivery devices. Other topics include evaluation/validation research usage of such software, applying simulated blood glucose data for prototype training/validation, and other research uses of placing technical information on the Web

MathModelica - An Extensible Modeling and Simulation Environment with Integrated Graphics and Literate Programming

OpenAIRE

Fritzson, Peter; Gunnarsson, Johan; Jirstrand, Mats

2002-01-01

MathModelica is an integrated interactive development environment for advanced system modeling and simulation. The environment integrates Modelica-based modeling and simulation with graphic design, advanced scripting facilities, integration of program code, test cases, graphics, documentation, mathematical type setting, and symbolic formula manipulation provided via Mathematica. The user interface consists of a graphical Model Editor and Notebooks. The Model Editor is a graphical user interfa...

A systematic review of the effectiveness of simulation-based education on satisfaction and learning outcomes in nurse practitioner programs.

Science.gov (United States)

Warren, Jessie N; Luctkar-Flude, Marian; Godfrey, Christina; Lukewich, Julia

2016-11-01

High-fidelity simulation (HFS) is becoming an integral component in healthcare education programs. There is considerable evidence demonstrating the effectiveness of HFS on satisfaction and learning outcomes within undergraduate nursing programs; however, there are few studies that have investigated its use and effectiveness within nurse practitioner (NP) programs. To synthesize the best available evidence about the effectiveness of HFS within NP education programs worldwide. The specific review question was: what is the effect of HFS on learner satisfaction, knowledge, attitudes, and skill performance in NP education? Joanna Briggs Institute systematic review methodology was utilized. The following databases were searched: MEDLINE, CINAHL, EMBASE, Epistemonikos, PROSPERO, HealthSTAR, AMED, Cochrane, Global Health and PsycINFO. Studies were included if they were quantitative in nature and reported on any aspect HFS within a NP program. Ten studies were included in the review. All studies were conducted in the United States and published between 2007 and 2014. Outcomes explored included: knowledge, attitudes, skills and satisfaction. The majority of studies compared HFS to online learning or traditional classroom lecture. Most study scenarios featured high acuity, low frequency events within acute care settings; only two studies utilized scenarios simulated within primary care. There is limited evidence supporting the use of HFS within NP programs. In general, HFS increases students' knowledge and confidence, and students are more satisfied with simulation-based teaching in comparison to other methods. Future studies should explore the effectiveness of simulation training within NP programs in reducing the theory to practice gap, and evaluate knowledge retention, transferability to real patient situations, and impact of simulation on patient outcomes. Copyright © 2016 Elsevier Ltd. All rights reserved.

A STUDY ON USING 3D VISUALIZATION AND SIMULATION PROGRAM (OPTITEX 3D ON LEATHER APPAREL

Directory of Open Access Journals (Sweden)

Ork Nilay

2016-05-01

Full Text Available Leather is a luxury garment. Design, material, labor, fitting and time costs are very effective on the production cost of the consumer leather good. 3D visualization and simulation programs which are getting popular in textile industry can be used for material, labor and time saving in leather apparel. However these programs have a very limited use in leather industry because leather material databases are not sufficient as in textile industry. In this research, firstly material properties of leather and textile fabric were determined by using both textile and leather physical test methods, and interpreted and introduced in the program. Detailed measures of an experimental human body were measured from a 3D body scanner. An avatar was designed according to these measurements. Then a prototype dress was made by using Computer Aided Design-CAD program for designing the patterns. After the pattern making, OptiTex 3D visualization and simulation program was used to visualize and simulate the dresses. Additionally the leather and cotton fabric dresses were sewn in real life. Then the visual and real life dresses were compared and discussed. 3D virtual prototyping seems a promising potential in future manufacturing technologies by evaluating the fitting of garments in a simple and quick way, filling the gap between 3D pattern design and manufacturing, providing virtual demonstrations to customers.

Generalized Fluid System Simulation Program, Version 5.0-Educational

Science.gov (United States)

Majumdar, A. K.

2011-01-01

The Generalized Fluid System Simulation Program (GFSSP) is a finite-volume based general-purpose computer program for analyzing steady state and time-dependent flow rates, pressures, temperatures, and concentrations in a complex flow network. The program is capable of modeling real fluids with phase changes, compressibility, mixture thermodynamics, conjugate heat transfer between solid and fluid, fluid transients, pumps, compressors and external body forces such as gravity and centrifugal. The thermofluid system to be analyzed is discretized into nodes, branches, and conductors. The scalar properties such as pressure, temperature, and concentrations are calculated at nodes. Mass flow rates and heat transfer rates are computed in branches and conductors. The graphical user interface allows users to build their models using the point, drag and click method; the users can also run their models and post-process the results in the same environment. The integrated fluid library supplies thermodynamic and thermo-physical properties of 36 fluids and 21 different resistance/source options are provided for modeling momentum sources or sinks in the branches. This Technical Memorandum illustrates the application and verification of the code through 12 demonstrated example problems.

TITAN: a computer program for accident occurrence frequency analyses by component Monte Carlo simulation

Energy Technology Data Exchange (ETDEWEB)

Nomura, Yasushi [Department of Fuel Cycle Safety Research, Nuclear Safety Research Center, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Tamaki, Hitoshi [Department of Safety Research Technical Support, Tokai Research Establishment, Japan Atomic Energy Research Institute, Tokai, Ibaraki (Japan); Kanai, Shigeru [Fuji Research Institute Corporation, Tokyo (Japan)

2000-04-01

In a plant system consisting of complex equipments and components for a reprocessing facility, there might be grace time between an initiating event and a resultant serious accident, allowing operating personnel to take remedial actions, thus, terminating the ongoing accident sequence. A component Monte Carlo simulation computer program TITAN has been developed to analyze such a complex reliability model including the grace time without any difficulty to obtain an accident occurrence frequency. Firstly, basic methods for the component Monte Carlo simulation is introduced to obtain an accident occurrence frequency, and then, the basic performance such as precision, convergence, and parallelization of calculation, is shown through calculation of a prototype accident sequence model. As an example to illustrate applicability to a real scale plant model, a red oil explosion in a German reprocessing plant model is simulated to show that TITAN can give an accident occurrence frequency with relatively good accuracy. Moreover, results of uncertainty analyses by TITAN are rendered to show another performance, and a proposal is made for introducing of a new input-data format to adapt the component Monte Carlo simulation. The present paper describes the calculational method, performance, applicability to a real scale, and new proposal for the TITAN code. In the Appendixes, a conventional analytical method is shown to avoid complex and laborious calculation to obtain a strict solution of accident occurrence frequency, compared with Monte Carlo method. The user's manual and the list/structure of program are also contained in the Appendixes to facilitate TITAN computer program usage. (author)

TITAN: a computer program for accident occurrence frequency analyses by component Monte Carlo simulation

International Nuclear Information System (INIS)

Nomura, Yasushi; Tamaki, Hitoshi; Kanai, Shigeru

2000-04-01

In a plant system consisting of complex equipments and components for a reprocessing facility, there might be grace time between an initiating event and a resultant serious accident, allowing operating personnel to take remedial actions, thus, terminating the ongoing accident sequence. A component Monte Carlo simulation computer program TITAN has been developed to analyze such a complex reliability model including the grace time without any difficulty to obtain an accident occurrence frequency. Firstly, basic methods for the component Monte Carlo simulation is introduced to obtain an accident occurrence frequency, and then, the basic performance such as precision, convergence, and parallelization of calculation, is shown through calculation of a prototype accident sequence model. As an example to illustrate applicability to a real scale plant model, a red oil explosion in a German reprocessing plant model is simulated to show that TITAN can give an accident occurrence frequency with relatively good accuracy. Moreover, results of uncertainty analyses by TITAN are rendered to show another performance, and a proposal is made for introducing of a new input-data format to adapt the component Monte Carlo simulation. The present paper describes the calculational method, performance, applicability to a real scale, and new proposal for the TITAN code. In the Appendixes, a conventional analytical method is shown to avoid complex and laborious calculation to obtain a strict solution of accident occurrence frequency, compared with Monte Carlo method. The user's manual and the list/structure of program are also contained in the Appendixes to facilitate TITAN computer program usage. (author)

Fusion Simulation Program Execution Plan

International Nuclear Information System (INIS)

Brooks, Jeffrey

2011-01-01

The overall science goal of the FSP is to develop predictive simulation capability for magnetically confined fusion plasmas at an unprecedented level of integration and fidelity. This will directly support and enable effective U.S. participation in research related to the International Thermonuclear Experimental Reactor (ITER) and the overall mission of delivering practical fusion energy. The FSP will address a rich set of scientific issues together with experimental programs, producing validated integrated physics results. This is very well aligned with the mission of the ITER Organization to coordinate with its members the integrated modeling and control of fusion plasmas, including benchmarking and validation activities. [1]. Initial FSP research will focus on two critical areas: 1) the plasma edge and 2) whole device modeling including disruption avoidance. The first of these problems involves the narrow plasma boundary layer and its complex interactions with the plasma core and the surrounding material wall. The second requires development of a computationally tractable, but comprehensive model that describes all equilibrium and dynamic processes at a sufficient level of detail to provide useful prediction of the temporal evolution of fusion plasma experiments. The initial driver for the whole device model (WDM) will be prediction and avoidance of discharge-terminating disruptions, especially at high performance, which are a critical impediment to successful operation of machines like ITER. If disruptions prove unable to be avoided, their associated dynamics and effects will be addressed in the next phase of the FSP. The FSP plan targets the needed modeling capabilities by developing Integrated Science Applications (ISAs) specific to their needs. The Pedestal-Boundary model will include boundary magnetic topology, cross-field transport of multi-species plasmas, parallel plasma transport, neutral transport, atomic physics and interactions with the plasma wall

Implementation and evaluation of a simulation curriculum for paediatric residency programs including just-in-time in situ mock codes.

Science.gov (United States)

Sam, Jonathan; Pierse, Michael; Al-Qahtani, Abdullah; Cheng, Adam

2012-02-01

To develop, implement and evaluate a simulation-based acute care curriculum in a paediatric residency program using an integrated and longitudinal approach. Curriculum framework consisting of three modular, year-specific courses and longitudinal just-in-time, in situ mock codes. Paediatric residency program at BC Children's Hospital, Vancouver, British Columbia. The three year-specific courses focused on the critical first 5 min, complex medical management and crisis resource management, respectively. The just-in-time in situ mock codes simulated the acute deterioration of an existing ward patient, prepared the actual multidisciplinary code team, and primed the surrounding crisis support systems. Each curriculum component was evaluated with surveys using a five-point Likert scale. A total of 40 resident surveys were completed after each of the modular courses, and an additional 28 surveys were completed for the overall simulation curriculum. The highest Likert scores were for hands-on skill stations, immersive simulation environment and crisis resource management teaching. Survey results also suggested that just-in-time mock codes were realistic, reinforced learning, and prepared ward teams for patient deterioration. A simulation-based acute care curriculum was successfully integrated into a paediatric residency program. It provides a model for integrating simulation-based learning into other training programs, as well as a model for any hospital that wishes to improve paediatric resuscitation outcomes using just-in-time in situ mock codes.

Modelling of reactor control and protection systems in the core simulator program GARLIC

International Nuclear Information System (INIS)

Beraha, D.; Lupas, O.; Ploegert, K.

1984-01-01

For analysis of the interaction between control and limitation systems and the power distribution in the reactor core, a valuable tool is provided by the joint simulation of the core and the interacting systems. To this purpose, the core simulator GARLIC has been enhanced by models of the systems for controlling and limiting the reactor power and the power distribution in the core as well as by modules for calculating safety related core parameters. The computer-based core protection system, first installed in the Grafenrheinfeld NPP, has been included in the simulation. In order to evaluate the accuracy of GARLIC-simulations, the code has been compared with a design code in the train of a verification phase. The report describes the program extensions and the results of the verification. (orig.) [de

A development of simulation and analytical program for through-diffusion experiments for a single layer of diffusion media

International Nuclear Information System (INIS)

Sato, Haruo

2001-01-01

A program (TDROCK1. FOR) for simulation and analysis of through-diffusion experiments for a single layer of diffusion media was developed. This program was made by Pro-Fortran language, which was suitable for scientific and technical calculations, and relatively easy explicit difference method was adopted for an analysis. In the analysis, solute concentration in the tracer cell as a function of time that we could not treat to date can be input and the decrease in the solute concentration as a function of time by diffusion from the tracer cell to the measurement cell, the solute concentration distribution in the porewater of diffusion media and the solute concentration in the measurement cell as a function of time can be calculated. In addition, solution volume in both cells and diameter and thickness of the diffusion media are also variable as an input condition. This simulation program could well explain measured result by simulating solute concentration in the measurement cell as a function of time for case which apparent and effective diffusion coefficients were already known. Based on this, the availability and applicability of this program to actual analysis and simulation were confirmed. This report describes the theoretical treatment for the through-diffusion experiments for a single layer of diffusion media, analytical model, an example of source program and the manual. (author)

Users manual for Aerospace Nuclear Safety Program six-degree-of-freedom reentry simulation (TMAGRA6C)

International Nuclear Information System (INIS)

Sharbaugh, R.C.

1990-02-01

This report documents the updated six-degree-of-freedom reentry simulation TMAGRA6C used in the Aerospace Nuclear Safety Program, ANSP. The simulation provides for the inclusion of the effects of ablation on the aerodynamic stability and drag of reentry bodies, specifically the General Purpose Heat Source, GPHS. The existing six-degree-of-freedom reentry body simulations (TMAGRA6A and TMAGRA6B) used in the JHU/APL Nuclear Safety Program do not include aerodynamic effects resulting from geometric changes to the configuration due to ablation from reentry flights. A wind tunnel test was conducted in 1989 to obtain the effects of ablation on the hypersonic aerodynamics of the GPHS module. The analyzed data were used to form data sets which are included herein in tabular form. These are used as incremental aerodynamic inputs in the new TMAGRA6C six-degree-of-freedom reentry simulation. 20 refs., 13 figs., 2 tabs

Changes in micro-relief during different water erosive stages of purple soil under simulated rainfall.

Science.gov (United States)

Luo, Jian; Zheng, Zicheng; Li, Tingxuan; He, Shuqin

2018-02-22

This study investigated the variation characteristics of micro-topography during successive erosive stages of water erosion: splash erosion (SpE), sheet erosion (ShE), and rill erosion (RE). Micro-topography was quantified using surface elevation change, soil roughness (SR) and multifractal model. Results showed that the area of soil surface elevation decay increased gradually with the development of water erosion. With rainfall, the combined effects of the detachment by raindrop impact and the transport of runoff decreased SR, whereas rill erosion contributed to increase SR. With the increase in slope gradient, soil erosion area gradually decreased at the splash erosion stage. By contrast, soil erosion area initially decreased and then increased at the sheet and rill erosion stages. The width of the D q spectra (ΔD) values increased at the splash erosion stage and then decreased at the sheet and rill erosion stages on the 10° slope, opposite to that on the 15° slope. The ΔD values decreased with the evolution of water erosive stages on the 20° slope. The slope had an enhancing effect on the evolution of water erosion. In this study, we clarified the essence of micro-topography and laid a theoretical foundation for further understanding diverse hydrological processes.

Educational program in crisis management for cardiac surgery teams including high realism simulation.

Science.gov (United States)

Stevens, Louis-Mathieu; Cooper, Jeffrey B; Raemer, Daniel B; Schneider, Robert C; Frankel, Allan S; Berry, William R; Agnihotri, Arvind K

2012-07-01

Cardiac surgery demands effective teamwork for safe, high-quality care. The objective of this pilot study was to develop a comprehensive program to sharpen performance of experienced cardiac surgical teams in acute crisis management. We developed and implemented an educational program for cardiac surgery based on high realism acute crisis simulation scenarios and interactive whole-unit workshop. The impact of these interventions was assessed with postintervention questionnaires, preintervention and 6-month postintervention surveys, and structured interviews. The realism of the acute crisis simulation scenarios gradually improved; most participants rated both the simulation and whole-unit workshop as very good or excellent. Repeat simulation training was recommended every 6 to 12 months by 82% of the participants. Participants of the interactive workshop identified 2 areas of highest priority: encouraging speaking up about critical information and interprofessional information sharing. They also stressed the importance of briefings, early communication of surgical plan, knowing members of the team, and continued simulation for practice. The pre/post survey response rates were 70% (55/79) and 66% (52/79), respectively. The concept of working as a team improved between surveys (P = .028), with a trend for improvement in gaining common understanding of the plan before a procedure (P = .075) and appropriate resolution of disagreements (P = .092). Interviewees reported that the training had a positive effect on their personal behaviors and patient care, including speaking up more readily and communicating more clearly. Comprehensive team training using simulation and a whole-unit interactive workshop can be successfully deployed for experienced cardiac surgery teams with demonstrable benefits in participant's perception of team performance. Copyright © 2012 The American Association for Thoracic Surgery. Published by Mosby, Inc. All rights reserved.

A testing program to evaluate the effects of simulant mixed wastes on plastic transportation packaging components

International Nuclear Information System (INIS)

Nigrey, P.J.; Dickens, T.G.

1997-01-01

Based on regulatory requirements for Type A and B radioactive material packaging, a Testing Program was developed to evaluate the effects of mixed wastes on plastic materials which could be used as liners and seals in transportation containers. The plastics evaluated in this program were butadiene-acrylonitrile copolymer (Nitrile rubber), cross-linked polyethylene, epichlorohydrin, ethylene-propylene rubber (EPDM), fluorocarbons, high-density polyethylene (HDPE), butyl rubber, polypropylene, polytetrafluoroethylene, and styrene-butadiene rubber (SBR). These plastics were first screened in four simulant mixed wastes. The liner materials were screened using specific gravity measurements and seal materials by vapor transport rate (VTR) measurements. For the screening of liner materials, Kel-F, HDPE, and XLPE were found to offer the greatest resistance to the combination of radiation and chemicals. The tests also indicated that while all seal materials passed exposure to the aqueous simulant mixed waste, EPDM and SBR had the lowest VTRs. In the chlorinated hydrocarbon simulant mixed waste, only Viton passed the screening tests. In both the simulant scintillation fluid mixed waste and the ketone mixture waste, none of the seal materials met the screening criteria. Those materials which passed the screening tests were subjected to further comprehensive testing in each of the simulant wastes. The materials were exposed to four different radiation doses followed by exposure to a simulant mixed waste at three temperatures and four different exposure times (7, 14, 28, 180 days). Materials were tested by measuring specific gravity, dimensional, hardness, stress cracking, VTR, compression set, and tensile properties. The second phase of this Testing Program involving the comprehensive testing of plastic liner has been completed and for seal materials is currently in progress

Modeling a Naturally Ventilated Double Skin Façade with a Building Thermal Simulation Program

DEFF Research Database (Denmark)

Jensen, Rasmus Lund; Kalyanova, Olena; Heiselberg, Per

2008-01-01

to predict. This is manly due to the very transient and complex air flow in the naturally ventilated double skin façade cavity. In this paper the modelling of the DSF using a thermal simulation program, BSim, is discussed. The simulations are based on the measured weather boundary conditions...

Results from the Splash Survey: Spectroscopic and Photometric Landscape of Andromeda's Stellar Halo

Science.gov (United States)

Guhathakurta, Puragra; SPLASH Collaboration

2009-01-01

Detailed studies of nearby galaxies provide vital clues about their formation and evolutionary history. This "fossil record" approach is complementary to direct look-back studies of distant galaxies. Our Galaxy and the Andromeda spiral galaxy (M31) have long been cornerstones in the former category. M31 provides an external perspective on a large galaxy similar to our own and yet is close enough to allow detailed studies of individual stars. In my talk, I will present results from the SPLASH collaboration: Spectroscopic and Photometric Landscape of Andromeda's Stellar Halo. The collective data set from this large international team includes thousands of Keck/DEIMOS spectra of individual red giant branch stars, ground-based deep wide-field imaging and photometry with KPNO/Mosaic, CFHT/MegaCam, and Subaru/Suprime-Cam, and ultra-deep pencil-beam probes with HST/ACS imaging reaching below the main-sequence turnoff. Our recent discovery of an extended stellar halo in M31 (R > 150 kpc) shows that most previous studies of its spheroid have been sampling its inner bulge-like spheroidal component, not its halo. In my talk I will touch upon several related topics related to the general theme of hierarchical galaxy formation including: M31's global structure and subcomponents (halo, bulge/central bar, and disk), stellar dynamics, statistical properties of substructure, detailed chemical abundance measurements, detailed forensic reconstruction of recent collision events, dwarf satellites as tracers and building blocks of larger galaxies, and empirical constraints on the tangential motion of the M31 system. I will also discuss recent results on the chemical abundance of the lowest luminosity Galactic satellites (recently discovered by SDSS) and implications for the formation of the Milky Way halo. This research was supported by funds from the National Science Foundation, NASA, and the Institute for Geophysics and Planetary Physics.

Simulation of Water Percolation in a FEBEX Bentonite Block using TOUGH2 Program

International Nuclear Information System (INIS)

Bru, A.

2001-01-01

We use Tough2 program to simulate the water percolation in a Febex bentonite Block. From obtained results, we conclude that mean field approximation does not describe this process because the heterogeneity of the medium it is not include in mathematical formalism. (Author) 17 refs

Toward a Monte Carlo program for simulating vapor-liquid phase equilibria from first principles

Energy Technology Data Exchange (ETDEWEB)

McGrath, M; Siepmann, J I; Kuo, I W; Mundy, C J; Vandevondele, J; Sprik, M; Hutter, J; Mohamed, F; Krack, M; Parrinello, M

2004-10-20

Efficient Monte Carlo algorithms are combined with the Quickstep energy routines of CP2K to develop a program that allows for Monte Carlo simulations in the canonical, isobaric-isothermal, and Gibbs ensembles using a first principles description of the physical system. Configurational-bias Monte Carlo techniques and pre-biasing using an inexpensive approximate potential are employed to increase the sampling efficiency and to reduce the frequency of expensive ab initio energy evaluations. The new Monte Carlo program has been validated through extensive comparison with molecular dynamics simulations using the programs CPMD and CP2K. Preliminary results for the vapor-liquid coexistence properties (T = 473 K) of water using the Becke-Lee-Yang-Parr exchange and correlation energy functionals, a triple-zeta valence basis set augmented with two sets of d-type or p-type polarization functions, and Goedecker-Teter-Hutter pseudopotentials are presented. The preliminary results indicate that this description of water leads to an underestimation of the saturated liquid density and heat of vaporization and, correspondingly, an overestimation of the saturated vapor pressure.

[Training of residents in obstetrics and gynecology: Assessment of an educational program including formal lectures and practical sessions using simulators].

Science.gov (United States)

Jordan, A; El Haloui, O; Breaud, J; Chevalier, D; Antomarchi, J; Bongain, A; Boucoiran, I; Delotte, J

2015-01-01

Evaluate an educational program in the training of residents in gynecology-obstetrics (GO) with a theory session and a practical session on simulators and analyze their learning curve. Single-center prospective study, at the university hospital (CHU). Two-day sessions were leaded in April and July 2013. An evaluation on obstetric and gynecological surgery simulator was available to all residents. Theoretical knowledge principles of obstetrics were evaluated early in the session and after formal lectures was taught to them. At the end of the first session, a satisfaction questionnaire was distributed to all participants. Twenty residents agreed to participate to the training sessions. Evaluation of theoretical knowledge: at the end of the session, the residents obtained a significant improvement in their score on 20 testing knowledge. Obstetrical simulator: a statistically significant improvement in scores on assessments simulator vaginal delivery between the first and second session. Subjectively, a larger increase feeling was seen after breech delivery simulation than for the cephalic vaginal delivery. However, the confidence level of the resident after breech delivery simulation has not been improved at the end of the second session. Simulation in gynecological surgery: a trend towards improvement in the time realized on the peg-transfer between the two sessions was noted. In the virtual simulation, no statistically significant differences showed, no improvement for in salpingectomy's time. Subjectively, the residents felt an increase in the precision of their gesture. Satisfaction: All residents have tried the whole program. They considered the pursuit of these sessions on simulators was necessary and even mandatory. The approach chosen by this structured educational program allowed a progression for the residents, both objectively and subjectively. This simulation program type for the resident's training would use this tool in assessing their skills and develop

A flexible simulation program for multitasking operating systems to investigate controllers in thermal solar systems

Energy Technology Data Exchange (ETDEWEB)

Wittwer, C.; Horlitz, O.; Rommel, M. [Fraunhofer Inst. for Solar Energy Systems ISE, Freiburg (Germany)

1996-12-31

This paper describes a new program CoISim to simulate systems with complex controllers which is based on a principle similar to the wide-spread modular program TRNSYS. To get an accurate response of this dynamic system, small time are used steps. A numerical integration algorithm is used which is especially suitable for solving a system of nonlinear equations. With time steps of 1 second, it is possible to observe the dynamic effect of ``matched flow systems`` where the flow is a continous function of the state. An important motivation for the development of this dynamic simulation model is the validation of system models. This will be possible by comparing simulations with real measurement data having different time steps. One of the main aims is to determine the dependence of the heat transfer in the collector and the heat exchanger and the flow speed of the fluid. The energy demand of the pump is greatly influenced very much by this dependency. The mass flow controller can be a simple ``two-position controller`` or, as well, a complex ``fuzzy controller``. To describe the fuzzy controller, a separate, commercially available development program may be used. The controller is usually implemented in ANSI-C. (orig.)

Method and simulation program informed decisions in the early stages of building design

DEFF Research Database (Denmark)

Petersen, Steffen; Svendsen, Svend

2010-01-01

variations. The program then presents the output in a way that enables designers to make informed decisions. The method and the program reduce the need for design iterations, reducing time consumption and construction costs, to obtain the intended energy performance and indoor environment....... for making informed decisions in the early stages of building design to fulfil performance requirements with regard to energy consumption and indoor environment. The method is operationalised in a program that utilises a simple simulation program to make performance predictions of user-defined parameter......The early stages of building design include a number of decisions which have a strong influence on the performance of the building throughout the rest of the process. It is therefore important that designers are aware of the consequences of these design decisions. This paper presents a method...

Simulation programs for ph.D. study of analysis, modeling and optimum design of solar domestic hot water systems

Energy Technology Data Exchange (ETDEWEB)

Lin Qin

1998-12-31

The design of solar domestic hot water (DHW) systems is a complex process, due to characteristics inherent in the solar heating technology. Recently, computer simulation has become a widely used technique to improve the understanding of the thermal processes in such systems. One of the main objects of the Ph.D. study of `Analysis, Modelling and optimum Design of Solar Domestic Hot Water Systems` is to develop and verify programs for carrying out the simulation and evaluation of the dynamic performance of solar DHW systems. During this study, simulation programs for hot water distribution networks and for certain types of solar DHW systems were developed. (au)

HEXBU-3D, a three-dimensional PWR-simulator program for hexagonal fuel assemblies

International Nuclear Information System (INIS)

Karvinen, E.

1981-06-01

HEXBU-3D is a three-dimensional nodal simulator program for PWR reactors. It is designed for a reactor core that consists of hexagonal fuel assemblies and of big follower-type control assemblies. The program solves two-group diffusion equations in homogenized fuel assembly geometry by a sophisticated nodal method. The treatment of feedback effects from xenon-poisoning, fuel temperature, moderator temperature and density and soluble boron concentration are included in the program. The nodal equations are solved by a fast two-level iteration technique and the eigenvalue can be either the effective multiplication factor or the boron concentration of the moderator. Burnup calculations are performed by tabulated sets of burnup-dependent cross sections evaluated by a cell burnup program. HEXBY-3D has been originally programmed in FORTRAN V for the UNIVAC 1108 computer, but there is also another version which is operable on the CDC CYBER 170 computer. (author)

Parameter identification using optimization techniques in the continuous simulation programs FORSIM and MACKSIM

International Nuclear Information System (INIS)

Carver, M.B.; Austin, C.F.; Ross, N.E.

1980-02-01

This report discusses the mechanics of automated parameter identification in simulation packages, and reviews available integration and optimization algorithms and their interaction within the recently developed optimization options in the FORSIM and MACKSIM simulation packages. In the MACKSIM mass-action chemical kinetics simulation package, the form and structure of the ordinary differential equations involved is known, so the implementation of an optimizing option is relatively straightforward. FORSIM, however, is designed to integrate ordinary and partial differential equations of abritrary definition. As the form of the equations is not known in advance, the design of the optimizing option is more intricate, but the philosophy could be applied to most simulation packages. In either case, however, the invocation of the optimizing interface is simple and user-oriented. Full details for the use of the optimizing mode for each program are given; specific applications are used as examples. (O.T.)

IGUN-A program for the simulation of positive ion extraction including magnetic fields

International Nuclear Information System (INIS)

Becker, R.; Herrmannsfeldt, W.B.

1992-01-01

IGUN is a program for the simulation of positive ion extraction from plasmas. It is based on the well known program EGUN for the calculation of electron and ion trajectories in electron guns and lenses. The mathematical treatment of the plasma sheath is based on a simple analytical model, which provides a numerically stable calculation of the sheath potentials. In contrast to other ion extraction programs, IGUN is able to determine the extracted ion current in succeeding cycles of iteration by itself. However, it is also possible to set values of current, plasma density, or ion current density. Either axisymmetric or rectangular coordinates can be used, including axisymmetric or transverse magnetic fields

igun - A program for the simulation of positive ion extraction including magnetic fields

Science.gov (United States)

Becker, R.; Herrmannsfeldt, W. B.

1992-04-01

igun is a program for the simulation of positive ion extraction from plasmas. It is based on the well known program egun for the calculation of electron and ion trajectories in electron guns and lenses. The mathematical treatment of the plasma sheath is based on a simple analytical model, which provides a numerically stable calculation of the sheath potentials. In contrast to other ion extraction programs, igun is able to determine the extracted ion current in succeeding cycles of iteration by itself. However, it is also possible to set values of current, plasma density, or ion current density. Either axisymmetric or rectangular coordinates can be used, including axisymmetric or transverse magnetic fields.

PSOD: an interactive Fortran program to simulate the radiation dose response of membrane populations

International Nuclear Information System (INIS)

Perry, K.A.; Szekely, J.G.

1982-04-01

Program PSOD was written to simulate the distribution in responses of membrane populations subjected to random radiation doses and dose rates. It computes the response (damage) according to one of three formulas selected by the user, and outputs statistical results to the terminal. It will plot simulated dose- and response-frequency distributions in two or three dimensions. Doses and dose rates are selected from the log normal distribution; other distributions can be incorporated as the need arises. A true log normal curve with defined mean and standard deviation can also be generated. The purpose of this documentation is to provide a complete operating manual for the program. A user guide is available on-line after initiating a session of PSOD. Detailed examinations of the statistical validity of various steps have been included to aid future modifications and updating

Comparison of Cardiopulmonary Resuscitation Quality Between Standard Versus Telephone-Basic Life Support Training Program in Middle-Aged and Elderly Housewives: A Randomized Simulation Study.

Science.gov (United States)

Kim, Tae Han; Lee, Yu Jin; Lee, Eui Jung; Ro, Young Sun; Lee, KyungWon; Lee, Hyeona; Jang, Dayea Beatrice; Song, Kyoung Jun; Shin, Sang Do; Myklebust, Helge; Birkenes, Tonje Søraas

2018-02-01

For cardiac arrests witnessed at home, the witness is usually a middle-aged or older housewife. We compared the quality of cardiopulmonary resuscitation (CPR) performance of bystanders trained with the newly developed telephone-basic life support (T-BLS) program and those trained with standard BLS (S-BLS) training programs. Twenty-four middle-aged and older housewives without previous CPR education were enrolled and randomized into two groups of BLS training programs. The T-BLS training program included concepts and current instruction protocols for telephone-assisted CPR, whereas the S-BLS training program provided training for BLS. After each training course, the participants simulated CPR and were assisted by a dispatcher via telephone. Cardiopulmonary resuscitation quality was measured and recorded using a mannequin simulator. The primary outcome was total no-flow time (>1.5 seconds without chest compression) during simulation. Among 24 participants, two (8.3%) who experienced mechanical failure of simulation mannequin and one (4.2%) who violated simulation protocols were excluded at initial simulation, and two (8.3%) refused follow-up after 6 months. The median (interquartile range) total no-flow time during initial simulation was 79.6 (66.4-96.9) seconds for the T-BLS training group and 147.6 (122.5-184.0) seconds for the S-BLS training group (P trained with the T-BLS training program showed shorter no-flow time and fewer interruptions during bystander CPR simulation assisted by a dispatcher.

Case report: a work simulation program for a manual worker with a fracture injury.

Science.gov (United States)

Chan, Chi-Chung; Chow, Jonathan H.W.

2000-01-01

Work rehabilitation programs targeting different client groups are available in nearly all major hospital occupational therapy departments in Hong Kong. Clients receiving work rehabilitation are referred from various out-patient clinics and other occupational therapists. Those clients experience limitation in work after their injuries or diseases and plan to return to work after rehabilitation. Program objectives are 1) to assist clients to reach maximum work capacity as rapidly as possible 2) to ensure clients return to work safely 3) to improve clients' work readiness. This case report describes an individualized work simulation program at a general hospital in Hong Kong provided for a typical client who is preparing to return to his worker role. Specific job analysis, goals and program rationale for the client are discussed.

Follow 1.1 - a program for visualization of Thermal-Hydraulic computer simulations. User's manual

International Nuclear Information System (INIS)

Hyvarinen, J.

1990-04-01

FOLLOW is a computer program designed to function as an analyst's aid when performing large thermalhydraulic and related safety calculations using the well known simulation codes RELAP5, MELCOR, SMABRE and TRAB. The code is a by-product of the effort to improve the analysis capabilities of the Finnish Centre for Radiation and Nuclear Safety (STUK). FOLLOW's most important application is as an on-line 'window' into the progress of the simulation calculation. The thermal-hydraulic analyses related to nuclear safety routinely require very long calculation times. FOLLOW provides a possibility to follow the course of the simulation and thus make observations of the results already during the simulation. FOLLOW's various outputs have been designed to mimic those available at nuclear power plant operators' console. Thus FOLLOW can also be used much like a nuclear power plant simulator. This manual describes the usages, features and input requirements of FOLLOW version 1.1, including a sample problem input and various outputs. (orig.)

Evaluating Outcomes of High Fidelity Simulation Curriculum in a Community College Nursing Program

Science.gov (United States)

Denlea, Gregory Richard

2017-01-01

This study took place at a Wake Technical Community College, a multi-campus institution in Raleigh, North Carolina. An evaluation of the return on investment in high fidelity simulation used by an associate degree of nursing program was conducted with valid and reliable instruments. The study demonstrated that comparable student outcomes are…

Extension of Generalized Fluid System Simulation Program's Fluid Property Database

Science.gov (United States)

Patel, Kishan

2011-01-01

This internship focused on the development of additional capabilities for the General Fluid Systems Simulation Program (GFSSP). GFSSP is a thermo-fluid code used to evaluate system performance by a finite volume-based network analysis method. The program was developed primarily to analyze the complex internal flow of propulsion systems and is capable of solving many problems related to thermodynamics and fluid mechanics. GFSSP is integrated with thermodynamic programs that provide fluid properties for sub-cooled, superheated, and saturation states. For fluids that are not included in the thermodynamic property program, look-up property tables can be provided. The look-up property tables of the current release version can only handle sub-cooled and superheated states. The primary purpose of the internship was to extend the look-up tables to handle saturated states. This involves a) generation of a property table using REFPROP, a thermodynamic property program that is widely used, and b) modifications of the Fortran source code to read in an additional property table containing saturation data for both saturated liquid and saturated vapor states. Also, a method was implemented to calculate the thermodynamic properties of user-fluids within the saturation region, given values of pressure and enthalpy. These additions required new code to be written, and older code had to be adjusted to accommodate the new capabilities. Ultimately, the changes will lead to the incorporation of this new capability in future versions of GFSSP. This paper describes the development and validation of the new capability.

PHAST Version 2-A Program for Simulating Groundwater Flow, Solute Transport, and Multicomponent Geochemical Reactions

Science.gov (United States)

Parkhurst, David L.; Kipp, Kenneth L.; Charlton, Scott R.

2010-01-01

The computer program PHAST (PHREEQC And HST3D) simulates multicomponent, reactive solute transport in three-dimensional saturated groundwater flow systems. PHAST is a versatile groundwater flow and solute-transport simulator with capabilities to model a wide range of equilibrium and kinetic geochemical reactions. The flow and transport calculations are based on a modified version of HST3D that is restricted to constant fluid density and constant temperature. The geochemical reactions are simulated with the geochemical model PHREEQC, which is embedded in PHAST. Major enhancements in PHAST Version 2 allow spatial data to be defined in a combination of map and grid coordinate systems, independent of a specific model grid (without node-by-node input). At run time, aquifer properties are interpolated from the spatial data to the model grid; regridding requires only redefinition of the grid without modification of the spatial data. PHAST is applicable to the study of natural and contaminated groundwater systems at a variety of scales ranging from laboratory experiments to local and regional field scales. PHAST can be used in studies of migration of nutrients, inorganic and organic contaminants, and radionuclides; in projects such as aquifer storage and recovery or engineered remediation; and in investigations of the natural rock/water interactions in aquifers. PHAST is not appropriate for unsaturated-zone flow, multiphase flow, or density-dependent flow. A variety of boundary conditions are available in PHAST to simulate flow and transport, including specified-head, flux (specified-flux), and leaky (head-dependent) conditions, as well as the special cases of rivers, drains, and wells. Chemical reactions in PHAST include (1) homogeneous equilibria using an ion-association or Pitzer specific interaction thermodynamic model; (2) heterogeneous equilibria between the aqueous solution and minerals, ion exchange sites, surface complexation sites, solid solutions, and gases; and

Simulating Vito

CERN Document Server

Fragapane, Alexander

2013-01-01

This paper discusses the techniques used to simulate the proposed upgrade to the ASPIC line at ISOLDE, VITO. It discusses the process used in the program SIMION by explaining how to start with an Autodesk Inventor drawing and import this into SIMION to get a working simulation. It then goes on to discuss the pieces of VITO which have been simulated in the program and how they were simulated. Finally, it explains a little about the simulations of the full beamline which have been done and discusses what still needs to be done.

Simulation Activity in Otolaryngology Residencies.

Science.gov (United States)

Deutsch, Ellen S; Wiet, Gregory J; Seidman, Michael; Hussey, Heather M; Malekzadeh, Sonya; Fried, Marvin P

2015-08-01

Simulation has become a valuable tool in medical education, and several specialties accept or require simulation as a resource for resident training or assessment as well as for board certification or maintenance of certification. This study investigates current simulation resources and activities in US otolaryngology residency programs and examines interest in advancing simulation training and assessment within the specialty. Web-based survey. US otolaryngology residency training programs. An electronic web-based survey was disseminated to all US otolaryngology program directors to determine their respective institutional and departmental simulation resources, existing simulation activities, and interest in further simulation initiatives. Descriptive results are reported. Responses were received from 43 of 104 (43%) residency programs. Simulation capabilities and resources are available in most respondents' institutions (78.6% report onsite resources; 73.8% report availability of models, manikins, and devices). Most respondents (61%) report limited simulation activity within otolaryngology. Areas of simulation are broad, addressing technical and nontechnical skills related to clinical training (94%). Simulation is infrequently used for research, credentialing, or systems improvement. The majority of respondents (83.8%) expressed interest in participating in multicenter trials of simulation initiatives. Most respondents from otolaryngology residency programs have incorporated some simulation into their curriculum. Interest among program directors to participate in future multicenter trials appears high. Future research efforts in this area should aim to determine optimal simulators and simulation activities for training and assessment as well as how to best incorporate simulation into otolaryngology residency training programs. © American Academy of Otolaryngology—Head and Neck Surgery Foundation 2015.

Purdue Contribution of Fusion Simulation Program

Energy Technology Data Exchange (ETDEWEB)

Jeffrey Brooks

2011-09-30

The overall science goal of the FSP is to develop predictive simulation capability for magnetically confined fusion plasmas at an unprecedented level of integration and fidelity. This will directly support and enable effective U.S. participation in research related to the International Thermonuclear Experimental Reactor (ITER) and the overall mission of delivering practical fusion energy. The FSP will address a rich set of scientific issues together with experimental programs, producing validated integrated physics results. This is very well aligned with the mission of the ITER Organization to coordinate with its members the integrated modeling and control of fusion plasmas, including benchmarking and validation activities. [1]. Initial FSP research will focus on two critical areas: 1) the plasma edge and 2) whole device modeling including disruption avoidance. The first of these problems involves the narrow plasma boundary layer and its complex interactions with the plasma core and the surrounding material wall. The second requires development of a computationally tractable, but comprehensive model that describes all equilibrium and dynamic processes at a sufficient level of detail to provide useful prediction of the temporal evolution of fusion plasma experiments. The initial driver for the whole device model (WDM) will be prediction and avoidance of discharge-terminating disruptions, especially at high performance, which are a critical impediment to successful operation of machines like ITER. If disruptions prove unable to be avoided, their associated dynamics and effects will be addressed in the next phase of the FSP. The FSP plan targets the needed modeling capabilities by developing Integrated Science Applications (ISAs) specific to their needs. The Pedestal-Boundary model will include boundary magnetic topology, cross-field transport of multi-species plasmas, parallel plasma transport, neutral transport, atomic physics and interactions with the plasma wall

Development of intelligent interface for simulation execution by module-based simulation system

International Nuclear Information System (INIS)

Yoshikawa, Hidekazu; Mizutani, Naoki; Shimoda, Hiroshi; Wakabayashi, Jiro

1988-01-01

An intelligent user support for the two phases of simulation execution was newly developed for Module-based Simulation System (MSS). The MSS has been in development as a flexible simulation environment to improve software productivity in complex, large-scale dynamic simulation of nuclear power plant. The AI programing by Smalltalk-80 was applied to materialize the two user-interface programs for (i) semantic diagnosis of the simulation program generated automatically by MSS, and (ii) consultation system by which user can set up consistent numerical input data files necessary for executing a MSS-generated program. Frame theory was utilized in those interface programs to represent the four knowledge bases, which are (i) usage information on module library in MSS and MSS-generated program, and (ii) expertise knowledge on nuclear power plant analysis such as material properties and reactor system configuration. Capabilities of those interface programs were confirmed by some example practice on LMFBR reactor dynamic calculation, and it was demonstrated that the knowledge-based systemization was effective to improve software work environment. (author)

Application of Compressible Volume of Fluid Model in Simulating the Impact and Solidification of Hollow Spherical ZrO2 Droplet on a Surface

Science.gov (United States)

Safaei, Hadi; Emami, Mohsen Davazdah; Jazi, Hamidreza Salimi; Mostaghimi, Javad

2017-12-01

Applications of hollow spherical particles in thermal spraying process have been developed in recent years, accompanied by attempts in the form of experimental and numerical studies to better understand the process of impact of a hollow droplet on a surface. During such process, volume and density of the trapped gas inside droplet change. The numerical models should be able to simulate such changes and their consequent effects. The aim of this study is to numerically simulate the impact of a hollow ZrO2 droplet on a flat surface using the volume of fluid technique for compressible flows. An open-source, finite-volume-based CFD code was used to perform the simulations, where appropriate subprograms were added to handle the studied cases. Simulation results were compared with the available experimental data. Results showed that at high impact velocities ( U 0 > 100 m/s), the compression of trapped gas inside droplet played a significant role in the impact dynamics. In such velocities, the droplet splashed explosively. Compressibility effects result in a more porous splat, compared to the corresponding incompressible model. Moreover, the compressible model predicted a higher spread factor than the incompressible model, due to planetary structure of the splat.

A 2-dimensional RBS simulation program for studying the edges of multilayer integrated circuit components

Energy Technology Data Exchange (ETDEWEB)

Guo, X.S.; Lanford, W.A. (Dept. of Physics, State Univ. of New York, Albany, NY (USA)); Rodbell, K.P. (IBM East Fishkill, Hopewell Junction, NY (USA))

1990-01-01

A computer program has been written to simulate the RBS spectrum from a sample consisting of many parallel three-layer stripes on a substrate (e.g. Al/Hf/Al stripes on SiO{sub 2}). The simulated RBS spectrum depends on the thickness of the different layers, the width of the stripes, the angle of the stripe side wall, the ion beam angle, the detector angle and the size and position of the ion beam on the stripe. The simulation fits experimental data well and can be used to determine diffusion in horizontal directions. It also provides an accurate way of measuring the angle of the stripe side wall. (orig.).

Early MIMD experience with a plasma physics simulation program on the CRAY X-MP

International Nuclear Information System (INIS)

Rhoades, C.E. Jr.

1986-02-01

This paper describes some early experience with converting a plasma physics simulation program to the CRAY X-MP, a current multiple instruction, multiple data (MIMD) computer consisting of two processors with architecture similar to that of the CRAY-1. The computer program used in this study is an all Fortran version of SELF, a two species, one space, two velocity, electromagnetic, Newtonian, particle in cell, plasma simulation code. The approach to converting SELF to use both processors of the CRAY X-MP is described in some detail. The resulting multiprocessor version of SELF is nearly a factor of two faster in real time than the single processor version. The multiprocessor version obtains 58.2+-.1 seconds of central processor time in 30+-.5 seconds of real time. For comparison, the CRAY-1 execution time if 74.5 seconds. For SELF, which is mostly scalar coding, the CRAY X-MP is about 2.5 times faster overall than the CRAY-1

The Analysis of Simulation Based Acquisition (SBA) Economic Breakpoints in the Life Cycle of Major Programs

National Research Council Canada - National Science Library

Hunt, George

2002-01-01

...). Application of SBA initiatives relies upon the use of modeling and simulation, among other methods, to effectively use scarce resources funds, manpower, equipment in the life cycle of major programs...

The development of WIPPVENT, a windows based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

McDaniel, K.H.

1995-01-01

An interactive mine ventilation simulation software program (WIPPVENT) was developed at the Waste Isolation Pilot Plant (WIPP). The WIPP is a US Department of Energy (DOE) research and development project located near Carlsbad, New Mexico. The facility is designed to provide a permanent, safe underground disposal of US defense generated transuranic waste in bedded salt. In addition to it's regular functions, the underground ventilation system is engineered to prevent the uncontrolled spread of radioactive materials in the unlikely event of a release. To enhance the operability system, Westinghouse Electric Corporation has developed an interactive mine ventilation simulation software program (WIPPVENT). While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC (copyright 1991 Mine Ventilation Services, Inc.), the user interface has been completely rewritten as a Windows reg-sign application and screen graphics have been added. WIPPVENT is designed to interact with the WIPP ventilation monitoring systems through the site wide Central Monitoring System

Cryogenic process simulation

International Nuclear Information System (INIS)

Panek, J.; Johnson, S.

1994-01-01

Combining accurate fluid property databases with a commercial equation-solving software package running on a desktop computer allows simulation of cryogenic processes without extensive computer programming. Computer simulation can be a powerful tool for process development or optimization. Most engineering simulations to date have required extensive programming skills in languages such as Fortran, Pascal, etc. Authors of simulation code have also usually been responsible for choosing and writing the particular solution algorithm. This paper describes a method of simulating cryogenic processes with a commercial software package on a desktop personal computer that does not require these traditional programming tasks. Applications include modeling of cryogenic refrigerators, heat exchangers, vapor-cooled power leads, vapor pressure thermometers, and various other engineering problems

Computerized Clinical Simulations.

Science.gov (United States)

Reinecker, Lynn

1985-01-01

Describes technique involved in designing a clinical simulation problem for the allied health field of respiratory therapy; discusses the structure, content, and scoring categories of the simulation; and provides a sample program which illustrates a programming technique in BASIC, including a program listing and a sample flowchart. (MBR)

Generalized Fluid System Simulation Program, Version 6.0

Science.gov (United States)

Majumdar, A. K.; LeClair, A. C.; Moore, R.; Schallhorn, P. A.

2016-01-01

The Generalized Fluid System Simulation Program (GFSSP) is a general purpose computer program for analyzing steady state and time-dependent flow rates, pressures, temperatures, and concentrations in a complex flow network. The program is capable of modeling real fluids with phase changes, compressibility, mixture thermodynamics, conjugate heat transfer between solid and fluid, fluid transients, pumps, compressors, and external body forces such as gravity and centrifugal. The thermofluid system to be analyzed is discretized into nodes, branches, and conductors. The scalar properties such as pressure, temperature, and concentrations are calculated at nodes. Mass flow rates and heat transfer rates are computed in branches and conductors. The graphical user interface allows users to build their models using the 'point, drag, and click' method; the users can also run their models and post-process the results in the same environment. Two thermodynamic property programs (GASP/WASP and GASPAK) provide required thermodynamic and thermophysical properties for 36 fluids: helium, methane, neon, nitrogen, carbon monoxide, oxygen, argon, carbon dioxide, fluorine, hydrogen, parahydrogen, water, kerosene (RP-1), isobutene, butane, deuterium, ethane, ethylene, hydrogen sulfide, krypton, propane, xenon, R-11, R-12, R-22, R-32, R-123, R-124, R-125, R-134A, R-152A, nitrogen trifluoride, ammonia, hydrogen peroxide, and air. The program also provides the options of using any incompressible fluid with constant density and viscosity or ideal gas. The users can also supply property tables for fluids that are not in the library. Twenty-four different resistance/source options are provided for modeling momentum sources or sinks in the branches. These options include pipe flow, flow through a restriction, noncircular duct, pipe flow with entrance and/or exit losses, thin sharp orifice, thick orifice, square edge reduction, square edge expansion, rotating annular duct, rotating radial duct

LIAR -- A new program for the modeling and simulation of linear accelerators with high gradients and small emittances

International Nuclear Information System (INIS)

Assmann, R.; Adolphsen, C.; Bane, K.; Raubenheimer, T.O.; Siemann, R.; Thompson, K.

1996-09-01

Linear accelerators are the central components of the proposed next generation of linear colliders. They need to provide acceleration of up to 750 GeV per beam while maintaining very small normalized emittances. Standard simulation programs, mainly developed for storage rings, do not meet the specific requirements for high energy linear accelerators. The authors present a new program LIAR (LInear Accelerator Research code) that includes wakefield effects, a 4D coupled beam description, specific optimization algorithms and other advanced features. Its modular structure allows to use and to extend it easily for different purposes. They present examples of simulations for SLC and NLC

A survey of electric and hybrid vehicles simulation programs. Volume 2: Questionnaire responses

Science.gov (United States)

Bevan, J.; Heimburger, D. A.; Metcalfe, M. A.

1978-01-01

The data received in a survey conducted within the United States to determine the extent of development and capabilities of automotive performance simulation programs suitable for electric and hybrid vehicle studies are presented. The survey was conducted for the Department of Energy by NASA's Jet Propulsion Laboratory. Volume 1 of this report summarizes and discusses the results contained in Volume 2.

Particle transport patterns of short-distance soil erosion by wind-driven rain, rain and wind

Science.gov (United States)

Marzen, Miriam; Iserloh, Thomas; de Lima, João L. M. P.; Ries, Johannes B.

2015-04-01

Short distance erosion of soil surface material is one of the big question marks in soil erosion studies. The exact measurement of short-distance transported soil particles, prior to the occurrence of overland flow, is a challenge to soil erosion science due to the particular requirements of the experimental setup and test procedure. To approach a quantification of amount and distance of each type of transport, we applied an especially developed multiple-gutter system installed inside the Trier Portable Wind and Rainfall Simulator (PWRS). We measured the amount and travel distance of soil particles detached and transported by raindrops (splash), wind-driven rain (splash-saltation and splash-drift) and wind (saltation). The test setup included three different erosion agents (rain/ wind-driven rain/ wind), two substrates (sandy/ loamy), three surface structures (grain roughness/ rills lengthwise/ rills transversal) and three slope angles (0°/+7°/-7°). The results present detailed transport patterns of the three erosion agents under the varying soil and surface conditions up to a distance of 1.6 m. Under the applied rain intensity and wind velocity, wind-driven rain splash generates the highest erosion. The erodibility and travel distance of the two substrates depend on the erosion agent. The total erosion is slightly higher for the slope angle -7° (downslope), but for wind-driven rain splash, the inclination is not a relevant factor. The effect of surface structures (rills) changes with traveling distance. The wind driven rain splash generates a much higher amount of erosion and a further travel distance of the particles due to the combined action of wind and rain. The wind-driven rain factor appears to be much more significant than the other factors. The study highlights the effects of different erosion agents and surface parameters on short-distance particle transport and the powerful impact of wind-driven rain on soil erosion.

C++QEDv2 Milestone 10: A C++/Python application-programming framework for simulating open quantum dynamics

Science.gov (United States)

Sandner, Raimar; Vukics, András

2014-09-01

The v2 Milestone 10 release of C++QED is primarily a feature release, which also corrects some problems of the previous release, especially as regards the build system. The adoption of C++11 features has led to many simplifications in the codebase. A full doxygen-based API manual [1] is now provided together with updated user guides. A largely automated, versatile new testsuite directed both towards computational and physics features allows for quickly spotting arising errors. The states of trajectories are now savable and recoverable with full binary precision, allowing for trajectory continuation regardless of evolution method (single/ensemble Monte Carlo wave-function or Master equation trajectory). As the main new feature, the framework now presents Python bindings to the highest-level programming interface, so that actual simulations for given composite quantum systems can now be performed from Python. Catalogue identifier: AELU_v2_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AELU_v2_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: yes No. of lines in distributed program, including test data, etc.: 492422 No. of bytes in distributed program, including test data, etc.: 8070987 Distribution format: tar.gz Programming language: C++/Python. Computer: i386-i686, x86 64. Operating system: In principle cross-platform, as yet tested only on UNIX-like systems (including Mac OS X). RAM: The framework itself takes about 60MB, which is fully shared. The additional memory taken by the program which defines the actual physical system (script) is typically less than 1MB. The memory storing the actual data scales with the system dimension for state-vector manipulations, and the square of the dimension for density-operator manipulations. This might easily be GBs, and often the memory of the machine limits the size of the simulated system. Classification: 4.3, 4.13, 6.2. External routines: Boost C

The computer program LIAR for the simulation and modeling of high performance linacs

International Nuclear Information System (INIS)

Assmann, R.; Adolphsen, C.; Bane, K.; Emma, P.; Raubenheimer, T.O.; Siemann, R.; Thompson, K.; Zimmermann, F.

1997-07-01

High performance linear accelerators are the central components of the proposed next generation of linear colliders. They must provide acceleration of up to 750 GeV per beam while maintaining small normalized emittances. Standard simulation programs, mainly developed for storage rings, did not meet the specific requirements for high performance linacs with high bunch charges and strong wakefields. The authors present the program. LIAR (LInear Accelerator Research code) that includes single and multi-bunch wakefield effects, a 6D coupled beam description, specific optimization algorithms and other advanced features. LIAR has been applied to and checked against the existing Stanford Linear Collider (SLC), the linacs of the proposed Next Linear Collider (NLC) and the proposed Linac Coherent Light Source (LCLS) at SLAC. Its modular structure allows easy extension for different purposes. The program is available for UNIX workstations and Windows PC's

State, space relay modeling and simulation using the electromagnetic Transients Program and its transient analysis of control systems capability

International Nuclear Information System (INIS)

Domijan, A.D. Jr.; Emami, M.V.

1990-01-01

This paper reports on a simulation of a MHO distance relay developed to study the effect of its operation under various system conditions. Simulation is accomplished using a state space approach and a modeling technique using ElectroMagnetic Transient Program (Transient Analysis of Control Systems). Furthermore, simulation results are compared with those obtained in another independent study as a control, to validate the results. A data code for the practical utilization of this simulation is given

Integration of simulation in postgraduate studies in Saudi Arabia: The current practice in anesthesia training program

Directory of Open Access Journals (Sweden)

Abeer Arab

2017-01-01

Full Text Available The educational programs in the Saudi Commission for Health Specialties are developing rapidly in the fields of technical development. Such development is witnessed, particularly in the scientific areas related to what is commonly known as evidence-based medicine. This review highlights the critical need and importance of integrating simulation into anesthesia training and assessment. Furthermore, it describes the current utilization of simulation in anesthesia and critical care assessment process.

CAD-based Monte Carlo program for integrated simulation of nuclear system SuperMC

International Nuclear Information System (INIS)

Wu, Yican; Song, Jing; Zheng, Huaqing; Sun, Guangyao; Hao, Lijuan; Long, Pengcheng; Hu, Liqin

2015-01-01

Highlights: • The new developed CAD-based Monte Carlo program named SuperMC for integrated simulation of nuclear system makes use of hybrid MC-deterministic method and advanced computer technologies. SuperMC is designed to perform transport calculation of various types of particles, depletion and activation calculation including isotope burn-up, material activation and shutdown dose, and multi-physics coupling calculation including thermo-hydraulics, fuel performance and structural mechanics. The bi-directional automatic conversion between general CAD models and physical settings and calculation models can be well performed. Results and process of simulation can be visualized with dynamical 3D dataset and geometry model. Continuous-energy cross section, burnup, activation, irradiation damage and material data etc. are used to support the multi-process simulation. Advanced cloud computing framework makes the computation and storage extremely intensive simulation more attractive just as a network service to support design optimization and assessment. The modular design and generic interface promotes its flexible manipulation and coupling of external solvers. • The new developed and incorporated advanced methods in SuperMC was introduced including hybrid MC-deterministic transport method, particle physical interaction treatment method, multi-physics coupling calculation method, geometry automatic modeling and processing method, intelligent data analysis and visualization method, elastic cloud computing technology and parallel calculation method. • The functions of SuperMC2.1 integrating automatic modeling, neutron and photon transport calculation, results and process visualization was introduced. It has been validated by using a series of benchmarking cases such as the fusion reactor ITER model and the fast reactor BN-600 model. - Abstract: Monte Carlo (MC) method has distinct advantages to simulate complicated nuclear systems and is envisioned as a routine

Development of the Simulation Program for the In-Vessel Fuel Handling System of Double Rotating Plug Type

International Nuclear Information System (INIS)

Kim, S. H.; Kim, J. B.

2011-01-01

In-vessel fuel handling machines are the main equipment of the in-vessel fuel handling system, which can move the core assembly inside the reactor vessel along with the rotating plug during refueling. The in vessel fuel handling machines for an advanced sodium cooled fast reactor(SFR) demonstration plant are composed of a direct lift machine(DM) and a fixed arm machine(FM). These machines should be able to access all areas above the reactor core by means of the rotating combination of double rotating plugs. Thus, in the in vessel fuel handling system of the double rotating plug type, it is necessary to decide the rotating plug size and evaluate the accessibility of in-vessel fuel handling machines in given core configuration. In this study, the simulation program based on LABVIEW which can effectively perform the arrangement design of the in vessel fuel handling system and simulate the rotating plug motion was developed. Fig. 1 shows the flow chart of the simulation program

Generalized Fluid System Simulation Program (GFSSP) Version 6 - General Purpose Thermo-Fluid Network Analysis Software

Science.gov (United States)

Majumdar, Alok; Leclair, Andre; Moore, Ric; Schallhorn, Paul

2011-01-01

GFSSP stands for Generalized Fluid System Simulation Program. It is a general-purpose computer program to compute pressure, temperature and flow distribution in a flow network. GFSSP calculates pressure, temperature, and concentrations at nodes and calculates flow rates through branches. It was primarily developed to analyze Internal Flow Analysis of a Turbopump Transient Flow Analysis of a Propulsion System. GFSSP development started in 1994 with an objective to provide a generalized and easy to use flow analysis tool for thermo-fluid systems.

Automating Embedded Analysis Capabilities and Managing Software Complexity in Multiphysics Simulation, Part I: Template-Based Generic Programming

Directory of Open Access Journals (Sweden)

Roger P. Pawlowski

2012-01-01

Full Text Available An approach for incorporating embedded simulation and analysis capabilities in complex simulation codes through template-based generic programming is presented. This approach relies on templating and operator overloading within the C++ language to transform a given calculation into one that can compute a variety of additional quantities that are necessary for many state-of-the-art simulation and analysis algorithms. An approach for incorporating these ideas into complex simulation codes through general graph-based assembly is also presented. These ideas have been implemented within a set of packages in the Trilinos framework and are demonstrated on a simple problem from chemical engineering.

Virtual Environment Computer Simulations to Support Human Factors Engineering and Operations Analysis for the RLV Program

Science.gov (United States)

Lunsford, Myrtis Leigh

1998-01-01

The Army-NASA Virtual Innovations Laboratory (ANVIL) was recently created to provide virtual reality tools for performing Human Engineering and operations analysis for both NASA and the Army. The author's summer research project consisted of developing and refining these tools for NASA's Reusable Launch Vehicle (RLV) program. Several general simulations were developed for use by the ANVIL for the evaluation of the X34 Engine Changeout procedure. These simulations were developed with the software tool dVISE 4.0.0 produced by Division Inc. All software was run on an SGI Indigo2 High Impact. This paper describes the simulations, various problems encountered with the simulations, other summer activities, and possible work for the future. We first begin with a brief description of virtual reality systems.

Performance demonstration program plan for analysis of simulated headspace gases

International Nuclear Information System (INIS)

1995-06-01

The Performance Demonstration Program (PDP) for analysis of headspace gases will consist of regular distribution and analyses of test standards to evaluate the capability for analyzing VOCs, hydrogen, and methane in the headspace of transuranic (TRU) waste throughout the Department of Energy (DOE) complex. Each distribution is termed a PDP cycle. These evaluation cycles will provide an objective measure of the reliability of measurements performed for TRU waste characterization. Laboratory performance will be demonstrated by the successful analysis of blind audit samples of simulated TRU waste drum headspace gases according to the criteria set within the text of this Program Plan. Blind audit samples (hereinafter referred to as PDP samples) will be used as an independent means to assess laboratory performance regarding compliance with the QAPP QAOs. The concentration of analytes in the PDP samples will encompass the range of concentrations anticipated in actual waste characterization gas samples. Analyses which are required by the WIPP to demonstrate compliance with various regulatory requirements and which are included in the PDP must be performed by laboratories which have demonstrated acceptable performance in the PDP

A quality assurance program of simulators in radiotherapy. Pt. 2. Extent and results of long-term quality assurance tests on a therapy simulator

International Nuclear Information System (INIS)

Mueller-Sievers, K.; Kober, B.

1997-01-01

Background: Since 1990 we follow a quality assurance program with periodical tests of functional performance values of a 16-year-old simulator. Material and Method: For this purpose we adopted and modified German standards for quality assurance on linear accelerators and international standards elaborated for simulators (International Electrotechnical Commission). The tests are subdivided into daily visual checks (light field indication, optical distance indicator, isocentre-indicating devices, indication of gantry and collimator angles) and monthly and annually tests of relevant simulator parameters. Some important examples demonstrate the small variation of parameters over 6 years: Position of the light field centre when rotating the collimator, diameter of the isocentre circle when rotating the gantry, accuracy of the isocentre indication device, and coincidence of light field and simulated radiation field. Results: As an important result we can state, that by these rigid periodic tests it was possible to detect and compensate deteriorations of simulators quality rapidly. Conclusions: Technical improvements and specific calling-in of maintenance personnel whenever felt appropriate provided performance characteristics of our old simulator which are required by international recommendations as a basis for modern radiotherapy. (orig.) [de

Comprehensive Performance Evaluation for Hydrological and Nutrients Simulation Using the Hydrological Simulation Program-Fortran in a Mesoscale Monsoon Watershed, China.

Science.gov (United States)

Li, Zhaofu; Luo, Chuan; Jiang, Kaixia; Wan, Rongrong; Li, Hengpeng

2017-12-19

The Hydrological Simulation Program-Fortran (HSPF) is a hydrological and water quality computer model that was developed by the United States Environmental Protection Agency. Comprehensive performance evaluations were carried out for hydrological and nutrient simulation using the HSPF model in the Xitiaoxi watershed in China. Streamflow simulation was calibrated from 1 January 2002 to 31 December 2007 and then validated from 1 January 2008 to 31 December 2010 using daily observed data, and nutrient simulation was calibrated and validated using monthly observed data during the period from July 2009 to July 2010. These results of model performance evaluation showed that the streamflows were well simulated over the study period. The determination coefficient ( R ²) was 0.87, 0.77 and 0.63, and the Nash-Sutcliffe coefficient of efficiency (Ens) was 0.82, 0.76 and 0.65 for the streamflow simulation in annual, monthly and daily time-steps, respectively. Although limited to monthly observed data, satisfactory performance was still achieved during the quantitative evaluation for nutrients. The R ² was 0.73, 0.82 and 0.92, and the Ens was 0.67, 0.74 and 0.86 for nitrate, ammonium and orthophosphate simulation, respectively. Some issues may affect the application of HSPF were also discussed, such as input data quality, parameter values, etc. Overall, the HSPF model can be successfully used to describe streamflow and nutrients transport in the mesoscale watershed located in the East Asian monsoon climate area. This study is expected to serve as a comprehensive and systematic documentation of understanding the HSPF model for wide application and avoiding possible misuses.

SAFSIM theory manual: A computer program for the engineering simulation of flow systems

Energy Technology Data Exchange (ETDEWEB)

Dobranich, D.

1993-12-01

SAFSIM (System Analysis Flow SIMulator) is a FORTRAN computer program for simulating the integrated performance of complex flow systems. SAFSIM provides sufficient versatility to allow the engineering simulation of almost any system, from a backyard sprinkler system to a clustered nuclear reactor propulsion system. In addition to versatility, speed and robustness are primary SAFSIM development goals. SAFSIM contains three basic physics modules: (1) a fluid mechanics module with flow network capability; (2) a structure heat transfer module with multiple convection and radiation exchange surface capability; and (3) a point reactor dynamics module with reactivity feedback and decay heat capability. Any or all of the physics modules can be implemented, as the problem dictates. SAFSIM can be used for compressible and incompressible, single-phase, multicomponent flow systems. Both the fluid mechanics and structure heat transfer modules employ a one-dimensional finite element modeling approach. This document contains a description of the theory incorporated in SAFSIM, including the governing equations, the numerical methods, and the overall system solution strategies.

An evolutionary programming based simulated annealing method for solving the unit commitment problem

Energy Technology Data Exchange (ETDEWEB)

Christober Asir Rajan, C. [Department of EEE, Pondicherry Engineering College, Pondicherry 605014 (India); Mohan, M.R. [Department of EEE, Anna University, Chennai 600 025 (India)

2007-09-15

This paper presents a new approach to solve the short-term unit commitment problem using an evolutionary programming based simulated annealing method. The objective of this paper is to find the generation scheduling such that the total operating cost can be minimized, when subjected to a variety of constraints. This also means that it is desirable to find the optimal generating unit commitment in the power system for the next H hours. Evolutionary programming, which happens to be a global optimisation technique for solving unit commitment Problem, operates on a system, which is designed to encode each unit's operating schedule with regard to its minimum up/down time. In this, the unit commitment schedule is coded as a string of symbols. An initial population of parent solutions is generated at random. Here, each schedule is formed by committing all the units according to their initial status (''flat start''). Here the parents are obtained from a pre-defined set of solution's, i.e. each and every solution is adjusted to meet the requirements. Then, a random recommitment is carried out with respect to the unit's minimum down times. And SA improves the status. The best population is selected by evolutionary strategy. The Neyveli Thermal Power Station (NTPS) Unit-II in India demonstrates the effectiveness of the proposed approach; extensive studies have also been performed for different power systems consists of 10, 26, 34 generating units. Numerical results are shown comparing the cost solutions and computation time obtained by using the Evolutionary Programming method and other conventional methods like Dynamic Programming, Lagrangian Relaxation and Simulated Annealing and Tabu Search in reaching proper unit commitment. (author)

LIAR -- A computer program for the modeling and simulation of high performance linacs

International Nuclear Information System (INIS)

Assmann, R.; Adolphsen, C.; Bane, K.; Emma, P.; Raubenheimer, T.; Siemann, R.; Thompson, K.; Zimmermann, F.

1997-04-01

The computer program LIAR (LInear Accelerator Research Code) is a numerical modeling and simulation tool for high performance linacs. Amongst others, it addresses the needs of state-of-the-art linear colliders where low emittance, high-intensity beams must be accelerated to energies in the 0.05-1 TeV range. LIAR is designed to be used for a variety of different projects. LIAR allows the study of single- and multi-particle beam dynamics in linear accelerators. It calculates emittance dilutions due to wakefield deflections, linear and non-linear dispersion and chromatic effects in the presence of multiple accelerator imperfections. Both single-bunch and multi-bunch beams can be simulated. Several basic and advanced optimization schemes are implemented. Present limitations arise from the incomplete treatment of bending magnets and sextupoles. A major objective of the LIAR project is to provide an open programming platform for the accelerator physics community. Due to its design, LIAR allows straight-forward access to its internal FORTRAN data structures. The program can easily be extended and its interactive command language ensures maximum ease of use. Presently, versions of LIAR are compiled for UNIX and MS Windows operating systems. An interface for the graphical visualization of results is provided. Scientific graphs can be saved in the PS and EPS file formats. In addition a Mathematica interface has been developed. LIAR now contains more than 40,000 lines of source code in more than 130 subroutines. This report describes the theoretical basis of the program, provides a reference for existing features and explains how to add further commands. The LIAR home page and the ONLINE version of this manual can be accessed under: http://www.slac.stanford.edu/grp/arb/rwa/liar.htm

PRoMoTo 2013 proceedings

OpenAIRE

Bishop, Judith; Tillmann, Nikolai; Puder, Arno; Naik, Vinayak

2013-01-01

Programming for Mobile and Touch (PRoMoTo'13) was held at the 2013 ACM SIGPLAN conference on Systems, Programming, Languages and Applications (SPLASH 2013), October 2013 in Indianapolis, USA. Submissions for this event were invited in the general area of mobile and touch-oriented programming languages and programming environments, and teaching of programming for mobile devices. These are proceedings of the PRoMoTo'13.

von Kármán Vortex Street within an Impacting Drop

KAUST Repository

Thoraval, Marie-Jean

2012-06-29

The splashing of a drop impacting onto a liquid pool produces a range of different sized microdroplets. At high impact velocities, the most significant source of these droplets is a thin liquid jet emerging at the start of the impact from the neck that connects the drop to the pool. We use ultrahigh-speed video imaging in combination with high-resolution numerical simulations to show how this ejecta gives way to irregular splashing. At higher Reynolds numbers, its base becomes unstable, shedding vortex rings into the liquid from the free surface in an axisymmetric von Kármán vortex street, thus breaking the ejecta sheet as it forms.

von Kármán Vortex Street within an Impacting Drop

KAUST Repository

Thoraval, Marie-Jean; Takehara, Kohsei; Etoh, Takeharu Goji; Popinet, Sté phane; Ray, Pascal; Josserand, Christophe; Zaleski, Sté phane; Thoroddsen, Sigurdur T

2012-01-01

The splashing of a drop impacting onto a liquid pool produces a range of different sized microdroplets. At high impact velocities, the most significant source of these droplets is a thin liquid jet emerging at the start of the impact from the neck that connects the drop to the pool. We use ultrahigh-speed video imaging in combination with high-resolution numerical simulations to show how this ejecta gives way to irregular splashing. At higher Reynolds numbers, its base becomes unstable, shedding vortex rings into the liquid from the free surface in an axisymmetric von Kármán vortex street, thus breaking the ejecta sheet as it forms.

SEDRX: A computer program for the simulation Si(Li) and Ge(Hp) x-ray detectors efficiency

International Nuclear Information System (INIS)

Benamar, M.A.; Benouali, A.; Tchantchane, A.; Azbouche, A.; Tobbeche, S. Centre de Developpement des Techniques Nucleaires, Algiers; Labo. des Techniques Nucleaires)

1992-12-01

The difficulties encountered in measuring the x-ray detectors efficiency has motivated to develop a computer program to simulate this parameter. this program computes the efficiency of detectors as a function of energy. the computation of this parameter is based on the fitting coefficients of absorption in the case of photoelectric, coherent and incoherent factors. These coefficients are given by Mc Master library or may be determined by the interpolation based on cubic splines

Splash M-knife versus Flush Knife BT in the technical outcomes of endoscopic submucosal dissection for early gastric cancer: a propensity score matching analysis.

Science.gov (United States)

Esaki, Mitsuru; Suzuki, Sho; Hayashi, Yasuyo; Yokoyama, Azusa; Abe, Shuichi; Hosokawa, Taizo; Ogino, Haruei; Akiho, Hirotada; Ihara, Eikichi; Ogawa, Yoshihiro

2018-02-27

Endoscopic submucosal dissection (ESD) is a standard treatment for early gastric cancer. A new multi-functional ESD device was developed to achieve complete ESD with a single device. A metal plate attached to its distal sheath achieves better hemostasis during the procedure than the other needle-knife device, Flush Knife BT®, that has been conventionally used. The aim of this study was to compare the technical outcomes of ESD for early gastric cancer using the Splash M-Knife® with those using the Flush Knife BT. We conducted a retrospective review of the case records of 149 patients with early gastric cancer treated with ESD using the needle-type ESD knives between January 2012 and August 2016 at Kitakyushu Municipal Medical Center. Lesions treated with ESD using the Splash M-knife (ESD-M) and the Flush Knife BT (ESD-F) were compared. Multivariate analyses and propensity score matching were used to compensate for the differences in age, gender, underlying disease, antithrombotic drug use, lesion location, lesion position, macroscopic type, tumor size, presence of ulceration, operator level and types of electrosurgical unit used. The primary endpoint was the requirement to use hemostatic forceps in the two groups. The secondary endpoints of procedure time, en bloc and complete resection rates, and adverse events rates were evaluated for the two groups. There were 73 patients in the ESD-M group, and 76 patients in the ESD-F group. Propensity score matching analysis created 45 matched pairs. Adjusted comparisons between the two groups showed a significantly lower usage rate of hemostatic forceps in the ESD-M group than in the ESD-F group (6.7% vs 84.4%, p < 0.001). Treatment outcomes showed an en bloc resection rate of 100% in both groups; complete resection rate of 95.6% vs 100%, p = 0.49; median procedure time of 74.0 min vs 71.0 min, p = 0.90; post-procedure bleeding of 2.2% vs 2.2%, p = 1, in the ESD-M and ESD-F groups, respectively. There were

Ordinary Chondrites Viewed as Reassembled 'Splash Ejecta'

Science.gov (United States)

Sanders, I. S.

1995-09-01

A case has already been made favouring chondrites as re-assembled "splash ejecta" following low velocity collisions between molten planetesimals[1]. Here I briefly review this hypothesis, then develop further arguments in its support. The scenario envisaged may be summarized as follows. Planetesimals grew to radii greater than 30 km in less than 1 Ma after the formation of CAIs, and they were heated rapidly by the decay of 26Al. By 2 Ma each planetesimal had a molten interior insulated by a cool, dusty carapace. Low velocity collisions at this stage released enormous, turbulent, expanding clouds of incandescent spray mixed with dust and solid grains from the carapace. The cloud constituted a rather special, transient nebular environment; as it cooled the melt droplets became chondrules. Much of the cloud's contents re-assembled under gravity onto the surface of the hot, residual planetesimal and the accumulated debris became re-heated and metamorphosed. Collisions recurred over the few million years that relative velocities remained low and planetesimals remained molten. Thus, the cumulative debris contained many recycled and broken chondrules. This scenario is apparently reconcilable with chondrule cooling rates, the preservation of clasts of "planetary" rock in chondrites, the retention of volatiles in chondrules, the preservation of solar chemistry and more than a dozen other features. Is it reasonable to claim that 30 km radius bodies existed by 1 Ma, and were substantially molten by 2 Ma? Cameron[2] argued that CAIs were saved from drifting into the sun by their incorporation, soon after formation, into planetesimals whose mass was sufficient to hold them in orbits, decoupled from the drag of nebular gas. Wetherill's models [3] show that many bodies >100 km radius may have formed on a timescale of 10^5 years. In these terms, the proposed 30 km by 1 Ma is quite conservative. Regarding 26Al heating, the remarkably constant initial ratio of 26Al/27Al (5 x 10

Beam trajectory simulation program at the National Institute of Nuclear Research Tandem Accelerator facility

International Nuclear Information System (INIS)

Murillo C, G.

1996-01-01

The main object of this thesis is to show in a clear and simple way to the people in general, the function of the Tandem Accelerator located on site the ININ facilities. For this presentation, a computer program was developed. The software written in C language in a structural form, simulates the ion production and its trajectory in a schematic and in an easy way to comprehend. According to the goals of this work, the simulation also shows details of some of the machine components like the source, the accelerator cavity, ,and the bombarding chamber. Electric and magnetic fields calculations are included for the 90 degrees bending magnet and quadrupoles. (Author)

Parallel Object Oriented MD Simulation Program for Long Time Simulations of Metallic Glasses and Undercooled Liquids

Science.gov (United States)

Böddeker, B.; Teichler, H.

The MD simulation program TABB is motivated by the need of long time simulations for the investigation of slow processes near the glass transition of glass forming alloys. TABB is written in C++ with a high degree of flexibility: TABB allows the use of any short ranged pair potentials or EAM potentials, by generating and using a spline representation of all functions and their derivatives. TABB supports several numerical integration algorithms like the Runge-Kotta or the modified Gear-predictor-corrector algorithm of order five. The boundary conditions can be chosen to resemble the geometry of bulk materials or films. The simulation box length or the pressure can be fixed for each dimension separately. TABB may be used in isokinetic, isoenergeric or canonic (with random forces) mode. TABB contains a simple instruction interpreter to easily control the parameters and options during the simulation. The same source code can be compiled either for workstations or for parallel computers. The main optimization goal of TABB is to allow long time simulations of medium or small sized systems. To make this possible, much attention is spent on the optimized communication between the nodes. TABB uses a domain decomposition procedure. To use many nodes with a small system, the domain size has to be small compared to the range of particle interactions. In the limit of many nodes for only few atoms, the bottle neck of communication is the latency time. TABB minimizes the number of pairs of domains containing atoms that interact between these domains. This procedure minimizes the need of communication calls between pairs of nodes. TABB decides automatically, to how many, and to which directions the decomposition shall be applied. E.g., in the case of one dimensional domain decomposition, the simulation box is only split into "slabs" along a selected direction. The three dimensional domain decomposition is best with respect to the number of interacting domains only for simulations

Expansive development of a decommissioning program 'recycle simulator' in nuclear power station

International Nuclear Information System (INIS)

Nishiuchi, T.; Ozaki, S.; Hironaga, M.

2004-01-01

A decommissioning program 'Recycle Simulator' should be put into practice in careful consideration of both recycle of non-radioactive wastes and reduce of radioactive wastes in the coming circulatory social system. Nevertheless current support systems for decommissioning planning mainly deal with decontamination, safety storage and dismantlement, so-called the prior part of the total decommissioning process. Authors emphasize the necessity of total planning of decommissioning including recycle or reuse of a large amount of demolition materials and are propelling the development of the multi expert system named 'Recycle Simulator'. This paper presents an algorithm of the recycling and reusing scenario of demolition materials and a summarized configuration. 'Recycle Simulator' for the demolished concrete was developed in 2000 and presented at a previous International Conference on Nuclear Engineering. Construction of a supporting multi expert system for the totally planning of decommissioning projects is objected by expansive development of the previous version. 3 main conclusions obtained from this paper are the following. (1) The previously developed expert system was advanced in its estimation function toward the satisfaction of decommissioning planners. (2) The applicability of the system was enlarged to all the radioactive and non-radioactive wastes, demolished metal and concrete products, in a corresponding site of decommissioning. (3) Finally decommissioning recycle simulator was completed in a harmonized unification. (authors)

Electric-car simulation

Science.gov (United States)

Chapman, C. P.; Slusser, R. A.

1980-01-01

PARAMET, interactive simulation program for parametric studies of electric vehicles, guides user through simulation by menu and series of prompts for input parameters. Program considers aerodynamic drag, rolling resistance, linear and rotational acceleration, and road gradient as forces acting on vehicle.

Education and training for operators using a full scope simulator and an its upgrading program in JOYO

International Nuclear Information System (INIS)

Sawada, Makoto; Terano, Toshihiro; Hunaki, Isao

1996-01-01

A JOYO full scope operator training simulator installed in 1983, is being used with high average unit availability factor of more than 70% per annum. The education and training for the operators using it has been greatly contributing to safety operation of the experimental fast reactor JOYO. The simulator mainly consisting of five control panels, a computer system having two computers and an instructor's console, is able to simulate the plant behaviors and the sequential processes with real time under normal or anomaly conditions. Now, according as the JOYO MK-ILL project which enhances the irradiation capability of JOYO, an upgrading program of the simulator is proceeding with the aim of advancing its efficient usage by improving the training function and the analytical accuracy of the simulator. (author)

Trends in programming languages for neuroscience simulations.

Science.gov (United States)

Davison, Andrew P; Hines, Michael L; Muller, Eilif

2009-01-01

Neuroscience simulators allow scientists to express models in terms of biological concepts, without having to concern themselves with low-level computational details of their implementation. The expressiveness, power and ease-of-use of the simulator interface is critical in efficiently and accurately translating ideas into a working simulation. We review long-term trends in the development of programmable simulator interfaces, and examine the benefits of moving from proprietary, domain-specific languages to modern dynamic general-purpose languages, in particular Python, which provide neuroscientists with an interactive and expressive simulation development environment and easy access to state-of-the-art general-purpose tools for scientific computing.

Trends in Programming Languages for Neuroscience Simulations

Science.gov (United States)

Davison, Andrew P.; Hines, Michael L.; Muller, Eilif

2009-01-01

Neuroscience simulators allow scientists to express models in terms of biological concepts, without having to concern themselves with low-level computational details of their implementation. The expressiveness, power and ease-of-use of the simulator interface is critical in efficiently and accurately translating ideas into a working simulation. We review long-term trends in the development of programmable simulator interfaces, and examine the benefits of moving from proprietary, domain-specific languages to modern dynamic general-purpose languages, in particular Python, which provide neuroscientists with an interactive and expressive simulation development environment and easy access to state-of-the-art general-purpose tools for scientific computing. PMID:20198154

Trends in programming languages for neuroscience simulations

Directory of Open Access Journals (Sweden)

Andrew P Davison

2009-12-01

Full Text Available Neuroscience simulators allow scientists to express models in terms of biological concepts, without having to concern themselves with low-level computational details of their implementation. The expressiveness, power and ease-of-use of the simulator interface is critical in efficiently and accurately translating ideas into a working simulation. We review long-term trends in the development of programmable simulator interfaces, and examine the benefits of moving from proprietary, domain-specific languages to modern dynamic general-purpose languages, in particular Python, which provide neuroscientists with an interactive and expressive simulation development environment and easy access to state-of-the-art general-purpose tools for scientific computing.

Multi-coupling dynamic model and 3d simulation program for in-situ leaching of uranium mining

International Nuclear Information System (INIS)

Tan Kaixuan; Zeng Sheng; Sang Xiao; Sun Bing

2010-01-01

The in-situ leaching of uranium mining is a very complicated non-linear dynamic system, which involves couplings and positive/negative feedback among many factors and processes. A comprehensive, coupled multi-factors and processes dynamic model and simulation method was established to study the in-situ leaching of uranium mining. The model accounts for most coupling among various processes as following: (1) rock texture mechanics and its evolution, (2)the incremental stress rheology of rock deformation, (3) 3-D viscoelastic/ plastic multi-deformation processes, (4) hydrofracturing, (5) tensorial (anisotropic) fracture and rock permeability, (6) water-rock interactions and mass-transport (both advective and diffusive), (7) dissolution-induced chemical compaction, (8) multi-phase fluid flow. A 3-D simulation program was compiled based on Fortran and C++. An example illustrating the application of this model to simulating acidification, production and terminal stage of in situ leaching of uranium mining is presented for the some mine in Xinjiang, China. This model and program can be used for theoretical study, mine design, production management, the study of contaminant transport and restoration in groundwater of in-situ leaching of uranium mining. (authors)

Modelling and simulating the transitory regimes in NPP using the MMS package programs

International Nuclear Information System (INIS)

Prisecaru, I.; Dupleac, Daniel; Constantinescu, Adrian Cornel

2003-01-01

This paper introduces a brief presentation of the preoccupation of modelling and simulating group at the Nuclear Power Plant Department of the Faculty of Power Plant Engineering in 'Politehnica' University of Bucharest in using the Modular Modeling System, MMS, package programs for the simulation of NPP transitory regimes. Nuclear power plants are large, non-linear systems with numerous interactions between its components. In the analysis of such complex systems, dynamic simulation is recognized as a powerful method of keeping track of the myriad of interactions. The MMS is a simulation tool that has built in models for plant components using a modular approach to dynamic simulation. The MMS software modules were developed to correspond to plant components that are familiar to power plant engineers. The interface specifications of the modules were defined so that the modules can be interconnected analogously to components in the actual plant. For some components, several modules of differing complexity are available. These alternative modules allow the user to choose the module appropriate to his application, i.e. a detailed model or a more economical model with less detail. The modular nature of the MMS allows the user to tailor the goal of his simulation to the complexity of the application and allows the user to develop independent subsystems that can be integrated into a larger simulation. The MMS module library contains modules for components for fossil and nuclear power plants. Each module is a mathematical model of a type of plant component formulated from first principles. The MMS uses a simulation language that provides features to simplify the development of simulations. Features important to the development of the MMS are the macro capability, automatic sorting of modeling equations, and integration algorithms. The macro capability is used to express the modeling equations for an MMS module. Since modules may be used more than once in the same simulation

An adaptive maneuvering logic computer program for the simulation of one-on-one air-to-air combat. Volume 1: General description

Science.gov (United States)

Burgin, G. H.; Fogel, L. J.; Phelps, J. P.

1975-01-01

A technique for computer simulation of air combat is described. Volume 1 decribes the computer program and its development in general terms. Two versions of the program exist. Both incorporate a logic for selecting and executing air combat maneuvers with performance models of specific fighter aircraft. In the batch processing version the flight paths of two aircraft engaged in interactive aerial combat and controlled by the same logic are computed. The realtime version permits human pilots to fly air-to-air combat against the adaptive maneuvering logic (AML) in Langley Differential Maneuvering Simulator (DMS). Volume 2 consists of a detailed description of the computer programs.

Simulations, Imaging, and Modeling: A Unique Theme for an Undergraduate Research Program in Biomechanics.

Science.gov (United States)

George, Stephanie M; Domire, Zachary J

2017-07-01

As the reliance on computational models to inform experiments and evaluate medical devices grows, the demand for students with modeling experience will grow. In this paper, we report on the 3-yr experience of a National Science Foundation (NSF) funded Research Experiences for Undergraduates (REU) based on the theme simulations, imaging, and modeling in biomechanics. While directly applicable to REU sites, our findings also apply to those creating other types of summer undergraduate research programs. The objective of the paper is to examine if a theme of simulations, imaging, and modeling will improve students' understanding of the important topic of modeling, provide an overall positive research experience, and provide an interdisciplinary experience. The structure of the program and the evaluation plan are described. We report on the results from 25 students over three summers from 2014 to 2016. Overall, students reported significant gains in the knowledge of modeling, research process, and graduate school based on self-reported mastery levels and open-ended qualitative responses. This theme provides students with a skill set that is adaptable to other applications illustrating the interdisciplinary nature of modeling in biomechanics. Another advantage is that students may also be able to continue working on their project following the summer experience through network connections. In conclusion, we have described the successful implementation of the theme simulation, imaging, and modeling for an REU site and the overall positive response of the student participants.

Qualitative Assessment of a 3D Simulation Program: Faculty, Students, and Bio-Organic Reaction Animations

Science.gov (United States)

Günersel, Adalet B.; Fleming, Steven A.

2013-01-01

Research shows that computer-based simulations and animations are especially helpful in fields such as chemistry where concepts are abstract and cannot be directly observed. Bio-Organic Reaction Animations (BioORA) is a freely available 3D visualization software program developed to help students understand the chemistry of biomolecular events.…

Improving Nurses' Peripheral Intravenous Catheter Insertion Knowledge, Confidence, and Skills Using a Simulation-Based Blended Learning Program

Science.gov (United States)

Keleekai, Nowai L.; Schuster, Catherine A.; Murray, Connie L.; King, Mary Anne; Stahl, Brian R.; Labrozzi, Laura J.; Gallucci, Susan; LeClair, Matthew W.; Glover, Kevin R.

2016-01-01

Introduction Peripheral intravenous catheter (PIVC) insertion is one of the most common invasive procedures performed in a hospital, but most nurses receive little formal training in this area. Blended PIVC insertion training programs that incorporate deliberate simulated practice have the potential to improve clinical practice and patient care. Methods The study was a randomized, wait-list control group with crossover using nurses on three medical/surgical units. Baseline PIVC knowledge, confidence, and skills assessments were completed for both groups. The intervention group then received a 2-hour PIVC online course, followed by an 8-hour live training course using a synergistic mix of three simulation tools. Both groups were then reassessed. After crossover, the wait-list group received the same intervention and both groups were reassessed. Results At baseline, both groups were similar for knowledge, confidence, and skills. Compared with the wait-list group, the intervention group had significantly higher scores for knowledge, confidence, and skills upon completing the training program. After crossover, the wait-list group had similarly higher scores for knowledge, confidence, and skills than the intervention group. Between the immediate preintervention and postintervention periods, the intervention group improved scores for knowledge by 31%, skills by 24%, and decreased confidence by 0.5%, whereas the wait-list group improved scores for knowledge by 28%, confidence by 16%, and skills by 15%. Conclusions Results demonstrate significant improvements in nurses' knowledge, confidence, and skills with the use of a simulation-based blended learning program for PIVC insertion. Transferability of these findings from a simulated environment into clinical practice should be further explored. PMID:27504890

Biofuels policy and the US market for motor fuels: Empirical analysis of ethanol splashing

Energy Technology Data Exchange (ETDEWEB)

Walls, W.D., E-mail: wdwalls@ucalgary.ca [Department of Economics, University of Calgary, 2500 University Drive NW, Calgary, Alberta, T2N 1N4 (Canada); Rusco, Frank; Kendix, Michael [US GAO (United States)

2011-07-15

Low ethanol prices relative to the price of gasoline blendstock, and tax credits, have resulted in discretionary blending at wholesale terminals of ethanol into fuel supplies above required levels-a practice known as ethanol splashing in industry parlance. No one knows precisely where or in what volume ethanol is being blended with gasoline and this has important implications for motor fuels markets: Because refiners cannot perfectly predict where ethanol will be blended with finished gasoline by wholesalers, they cannot know when to produce and where to ship a blendstock that when mixed with ethanol at 10% would create the most economically efficient finished motor gasoline that meets engine standards and has comparable evaporative emissions as conventional gasoline without ethanol blending. In contrast to previous empirical analyses of biofuels that have relied on highly aggregated data, our analysis is disaggregated to the level of individual wholesale fuel terminals or racks (of which there are about 350 in the US). We incorporate the price of ethanol as well as the blendstock price to model the wholesaler's decision of whether or not to blend additional ethanol into gasoline at any particular wholesale city-terminal. The empirical analysis illustrates how ethanol and gasoline prices affect ethanol usage, controlling for fuel specifications, blend attributes, and city-terminal-specific effects that, among other things, control for differential costs of delivering ethanol from bio-refinery to wholesale rack. - Research Highlights: > Low ethanol prices and tax credits have resulted in discretionary blending of ethanol into fuel supplies above required levels. > This has important implications for motor fuels markets and vehicular emissions. > Our analysis incorporates the price of ethanol as well as the blendstock price to model the wholesaler's decision of whether or not to blend additional ethanol into gasoline at any particular wholesale city

Biofuels policy and the US market for motor fuels: Empirical analysis of ethanol splashing

International Nuclear Information System (INIS)

Walls, W.D.; Rusco, Frank; Kendix, Michael

2011-01-01

Low ethanol prices relative to the price of gasoline blendstock, and tax credits, have resulted in discretionary blending at wholesale terminals of ethanol into fuel supplies above required levels-a practice known as ethanol splashing in industry parlance. No one knows precisely where or in what volume ethanol is being blended with gasoline and this has important implications for motor fuels markets: Because refiners cannot perfectly predict where ethanol will be blended with finished gasoline by wholesalers, they cannot know when to produce and where to ship a blendstock that when mixed with ethanol at 10% would create the most economically efficient finished motor gasoline that meets engine standards and has comparable evaporative emissions as conventional gasoline without ethanol blending. In contrast to previous empirical analyses of biofuels that have relied on highly aggregated data, our analysis is disaggregated to the level of individual wholesale fuel terminals or racks (of which there are about 350 in the US). We incorporate the price of ethanol as well as the blendstock price to model the wholesaler's decision of whether or not to blend additional ethanol into gasoline at any particular wholesale city-terminal. The empirical analysis illustrates how ethanol and gasoline prices affect ethanol usage, controlling for fuel specifications, blend attributes, and city-terminal-specific effects that, among other things, control for differential costs of delivering ethanol from bio-refinery to wholesale rack. - Research highlights: → Low ethanol prices and tax credits have resulted in discretionary blending of ethanol into fuel supplies above required levels. → This has important implications for motor fuels markets and vehicular emissions. → Our analysis incorporates the price of ethanol as well as the blendstock price to model the wholesaler's decision of whether or not to blend additional ethanol into gasoline at any particular wholesale city-terminal. �

HIGHTEX: a computer program for the steady-state simulation of steam-methane reformers used in a nuclear process heat plant

International Nuclear Information System (INIS)

Tadokoro, Yoshihiro; Seya, Toko

1977-08-01

This report describes a computational model and the input procedure of HIGHTEX, a computer program for steady-state simulation of the steam-methane reformers used in a nuclear process heat plant. The HIGHTEX program simulates rapidly a single reformer tube, and treats the reactant single-phase in the two-dimensional catalyst bed. Output of the computer program is radial distributions of temperature and reaction products in the catalyst-packed bed, pressure loss of the packed bed, stress in the reformer tube, hydrogen permeation rate through the reformer tube, heat rate of reaction, and heat-transfer rate between helium and process gas. The running time (cpu) for a 9m-long bayonet type reformer tube is 12 min with FACOM-230/75. (auth.)

Genetic Gain and Inbreeding from Genomic Selection in a Simulated Commercial Breeding Program for Perennial Ryegrass

Directory of Open Access Journals (Sweden)

Zibei Lin

2016-03-01

Full Text Available Genomic selection (GS provides an attractive option for accelerating genetic gain in perennial ryegrass ( improvement given the long cycle times of most current breeding programs. The present study used simulation to investigate the level of genetic gain and inbreeding obtained from GS breeding strategies compared with traditional breeding strategies for key traits (persistency, yield, and flowering time. Base population genomes were simulated through random mating for 60,000 generations at an effective population size of 10,000. The degree of linkage disequilibrium (LD in the resulting population was compared with that obtained from empirical studies. Initial parental varieties were simulated to match diversity of current commercial cultivars. Genomic selection was designed to fit into a company breeding program at two selection points in the breeding cycle (spaced plants and miniplot. Genomic estimated breeding values (GEBVs for productivity traits were trained with phenotypes and genotypes from plots. Accuracy of GEBVs was 0.24 for persistency and 0.36 for yield for single plants, while for plots it was lower (0.17 and 0.19, respectively. Higher accuracy of GEBVs was obtained for flowering time (up to 0.7, partially as a result of the larger reference population size that was available from the clonal row stage. The availability of GEBVs permit a 4-yr reduction in cycle time, which led to at least a doubling and trebling genetic gain for persistency and yield, respectively, than the traditional program. However, a higher rate of inbreeding per cycle among varieties was also observed for the GS strategy.

Genetic Gain and Inbreeding from Genomic Selection in a Simulated Commercial Breeding Program for Perennial Ryegrass.

Science.gov (United States)

Lin, Zibei; Cogan, Noel O I; Pembleton, Luke W; Spangenberg, German C; Forster, John W; Hayes, Ben J; Daetwyler, Hans D

2016-03-01

Genomic selection (GS) provides an attractive option for accelerating genetic gain in perennial ryegrass () improvement given the long cycle times of most current breeding programs. The present study used simulation to investigate the level of genetic gain and inbreeding obtained from GS breeding strategies compared with traditional breeding strategies for key traits (persistency, yield, and flowering time). Base population genomes were simulated through random mating for 60,000 generations at an effective population size of 10,000. The degree of linkage disequilibrium (LD) in the resulting population was compared with that obtained from empirical studies. Initial parental varieties were simulated to match diversity of current commercial cultivars. Genomic selection was designed to fit into a company breeding program at two selection points in the breeding cycle (spaced plants and miniplot). Genomic estimated breeding values (GEBVs) for productivity traits were trained with phenotypes and genotypes from plots. Accuracy of GEBVs was 0.24 for persistency and 0.36 for yield for single plants, while for plots it was lower (0.17 and 0.19, respectively). Higher accuracy of GEBVs was obtained for flowering time (up to 0.7), partially as a result of the larger reference population size that was available from the clonal row stage. The availability of GEBVs permit a 4-yr reduction in cycle time, which led to at least a doubling and trebling genetic gain for persistency and yield, respectively, than the traditional program. However, a higher rate of inbreeding per cycle among varieties was also observed for the GS strategy. Copyright © 2016 Crop Science Society of America.

A simulation program for electronics experiments

International Nuclear Information System (INIS)

Brun, R.; Hagelberg, R.; Hansroul, M.; Lassalle, Jc.

1978-01-01

A general description of the GEANT program is given. The GEANT program has been designed to cover a wide variety of particle detectors. The program is separated into 4 independent parts: kinematics generation, trackina in space, tracks intersection with detectors and digitization of detector information. The tracking requires the introduction of the experimental set-up description in terms of media. The detectors are described independently of the media in a separate way. The media and detector description have to be furnished by the user. The implementation of the GEANT program is based on 2 sets of subprograms: a fixed set of subprograms, which are independent of the experimental situation and thus transparent to the user; a set of user subprograms which should be written by the user. The GEANT program produces results stored in data banks, which the user can convert into his own format. In addition the GEANT program provides printed and graphical outputs

MONTEC, an interactive fortran program to simulate radiation dose and dose-rate responses of populations

International Nuclear Information System (INIS)

Perry, K.A.; Szekely, J.G.

1983-09-01

The computer program MONTEC was written to simulate the distribution of responses in a population whose members are exposed to multiple radiation doses at variable dose rates. These doses and dose rates are randomly selected from lognormal distributions. The individual radiation responses are calculated from three equations, which include dose and dose-rate terms. Other response-dose/rate relationships or distributions can be incorporated by the user as the need arises. The purpose of this documentation is to provide a complete operating manual for the program. This version is written in FORTRAN-10 for the DEC system PDP-10

Ecological impact in ditch mesocosms of simulated spray drift from a crop protection program for potatoes

NARCIS (Netherlands)

Arts, G.H.P.; Buijse-Bogdan, L.L.; Belgers, J.D.M.; Rhenen-Kersten, van C.H.; Wijngaarden, van R.P.A.; Roessink, I.; Maund, S.J.; Brink, van den P.J.; Brock, T.C.M.

2006-01-01

Outdoor aquatic ditch mesocosms were treated with a range of pesticides to simulate various spray drift rates resulting from a typical crop protection program used in the cultivation of potatoes in The Netherlands. The main experimental aims of the present study were to provide information on the

SAGRAD: A Program for Neural Network Training with Simulated Annealing and the Conjugate Gradient Method.

Science.gov (United States)

Bernal, Javier; Torres-Jimenez, Jose

2015-01-01

SAGRAD (Simulated Annealing GRADient), a Fortran 77 program for computing neural networks for classification using batch learning, is discussed. Neural network training in SAGRAD is based on a combination of simulated annealing and Møller's scaled conjugate gradient algorithm, the latter a variation of the traditional conjugate gradient method, better suited for the nonquadratic nature of neural networks. Different aspects of the implementation of the training process in SAGRAD are discussed, such as the efficient computation of gradients and multiplication of vectors by Hessian matrices that are required by Møller's algorithm; the (re)initialization of weights with simulated annealing required to (re)start Møller's algorithm the first time and each time thereafter that it shows insufficient progress in reaching a possibly local minimum; and the use of simulated annealing when Møller's algorithm, after possibly making considerable progress, becomes stuck at a local minimum or flat area of weight space. Outlines of the scaled conjugate gradient algorithm, the simulated annealing procedure and the training process used in SAGRAD are presented together with results from running SAGRAD on two examples of training data.

Scientific and Computational Challenges of the Fusion Simulation Program (FSP)

International Nuclear Information System (INIS)

Tang, William M.

2011-01-01

This paper highlights the scientific and computational challenges facing the Fusion Simulation Program (FSP) a major national initiative in the United States with the primary objective being to enable scientific discovery of important new plasma phenomena with associated understanding that emerges only upon integration. This requires developing a predictive integrated simulation capability for magnetically-confined fusion plasmas that are properly validated against experiments in regimes relevant for producing practical fusion energy. It is expected to provide a suite of advanced modeling tools for reliably predicting fusion device behavior with comprehensive and targeted science-based simulations of nonlinearly-coupled phenomena in the core plasma, edge plasma, and wall region on time and space scales required for fusion energy production. As such, it will strive to embody the most current theoretical and experimental understanding of magnetic fusion plasmas and to provide a living framework for the simulation of such plasmas as the associated physics understanding continues to advance over the next several decades. Substantive progress on answering the outstanding scientific questions in the field will drive the FSP toward its ultimate goal of developing the ability to predict the behavior of plasma discharges in toroidal magnetic fusion devices with high physics fidelity on all relevant time and space scales. From a computational perspective, this will demand computing resources in the petascale range and beyond together with the associated multi-core algorithmic formulation needed to address burning plasma issues relevant to ITER - a multibillion dollar collaborative experiment involving seven international partners representing over half the world's population. Even more powerful exascale platforms will be needed to meet the future challenges of designing a demonstration fusion reactor (DEMO). Analogous to other major applied physics modeling projects (e

Scientific and computational challenges of the fusion simulation program (FSP)

International Nuclear Information System (INIS)

Tang, William M.

2011-01-01

This paper highlights the scientific and computational challenges facing the Fusion Simulation Program (FSP) - a major national initiative in the United States with the primary objective being to enable scientific discovery of important new plasma phenomena with associated understanding that emerges only upon integration. This requires developing a predictive integrated simulation capability for magnetically-confined fusion plasmas that are properly validated against experiments in regimes relevant for producing practical fusion energy. It is expected to provide a suite of advanced modeling tools for reliably predicting fusion device behavior with comprehensive and targeted science-based simulations of nonlinearly-coupled phenomena in the core plasma, edge plasma, and wall region on time and space scales required for fusion energy production. As such, it will strive to embody the most current theoretical and experimental understanding of magnetic fusion plasmas and to provide a living framework for the simulation of such plasmas as the associated physics understanding continues to advance over the next several decades. Substantive progress on answering the outstanding scientific questions in the field will drive the FSP toward its ultimate goal of developing the ability to predict the behavior of plasma discharges in toroidal magnetic fusion devices with high physics fidelity on all relevant time and space scales. From a computational perspective, this will demand computing resources in the petascale range and beyond together with the associated multi-core algorithmic formulation needed to address burning plasma issues relevant to ITER - a multibillion dollar collaborative experiment involving seven international partners representing over half the world's population. Even more powerful exascale platforms will be needed to meet the future challenges of designing a demonstration fusion reactor (DEMO). Analogous to other major applied physics modeling projects (e

Study protocol for the evaluation of an Infant Simulator based program delivered in schools: a pragmatic cluster randomised controlled trial

OpenAIRE

Brinkman, Sally A; Johnson, Sarah E; Lawrence, David; Codde, James P; Hart, Michael B; Straton, Judith AY; Silburn, Sven

2010-01-01

Abstract Background This paper presents the study protocol for a pragmatic randomised controlled trial to evaluate the impact of a school based program developed to prevent teenage pregnancy. The program includes students taking care of an Infant Simulator; despite growing popularity and an increasing global presence of such programs, there is no published evidence of their long-term impact. The aim of this trial is to evaluate the Virtual Infant Parenting (VIP) program by investigating pre-c...

Multi-Phase Modeling of Rainbird Water Injection

Science.gov (United States)

Vu, Bruce T.; Moss, Nicholas; Sampson, Zoe

2014-01-01

This paper describes the use of a Volume of Fluid (VOF) multiphase model to simulate the water injected from a rainbird nozzle used in the sound suppression system during launch. The simulations help determine the projectile motion for different water flow rates employed at the pad, as it is critical to know if water will splash on the first-stage rocket engine during liftoff.

Bourbaki's structure theory in the problem of complex systems simulation models synthesis and model-oriented programming

Science.gov (United States)

Brodsky, Yu. I.

2015-01-01

The work is devoted to the application of Bourbaki's structure theory to substantiate the synthesis of simulation models of complex multicomponent systems, where every component may be a complex system itself. An application of the Bourbaki's structure theory offers a new approach to the design and computer implementation of simulation models of complex multicomponent systems—model synthesis and model-oriented programming. It differs from the traditional object-oriented approach. The central concept of this new approach and at the same time, the basic building block for the construction of more complex structures is the concept of models-components. A model-component endowed with a more complicated structure than, for example, the object in the object-oriented analysis. This structure provides to the model-component an independent behavior-the ability of standard responds to standard requests of its internal and external environment. At the same time, the computer implementation of model-component's behavior is invariant under the integration of models-components into complexes. This fact allows one firstly to construct fractal models of any complexity, and secondly to implement a computational process of such constructions uniformly-by a single universal program. In addition, the proposed paradigm allows one to exclude imperative programming and to generate computer code with a high degree of parallelism.

A dialogue simulator program TREDI

International Nuclear Information System (INIS)

Bezruk, A.I.; Gaevenko, A.B.; Ivanov, Yu.V.

1989-01-01

A specialized program providing in a dialogue with an operator the calculation and representation of beam envelopes by passing the transport channel was described. The possibility of optimality visual evaluation of the seting up of optical element conditions, the condition correction and the whole problem complex in operator training on channel control procedure was envisaged. The program provides for the operation at IVK-2 SM 1420 complex. 5 refs

AESS: Accelerated Exact Stochastic Simulation

Science.gov (United States)

Jenkins, David D.; Peterson, Gregory D.

2011-12-01

The Stochastic Simulation Algorithm (SSA) developed by Gillespie provides a powerful mechanism for exploring the behavior of chemical systems with small species populations or with important noise contributions. Gene circuit simulations for systems biology commonly employ the SSA method, as do ecological applications. This algorithm tends to be computationally expensive, so researchers seek an efficient implementation of SSA. In this program package, the Accelerated Exact Stochastic Simulation Algorithm (AESS) contains optimized implementations of Gillespie's SSA that improve the performance of individual simulation runs or ensembles of simulations used for sweeping parameters or to provide statistically significant results. Program summaryProgram title: AESS Catalogue identifier: AEJW_v1_0 Program summary URL:http://cpc.cs.qub.ac.uk/summaries/AEJW_v1_0.html Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland Licensing provisions: University of Tennessee copyright agreement No. of lines in distributed program, including test data, etc.: 10 861 No. of bytes in distributed program, including test data, etc.: 394 631 Distribution format: tar.gz Programming language: C for processors, CUDA for NVIDIA GPUs Computer: Developed and tested on various x86 computers and NVIDIA C1060 Tesla and GTX 480 Fermi GPUs. The system targets x86 workstations, optionally with multicore processors or NVIDIA GPUs as accelerators. Operating system: Tested under Ubuntu Linux OS and CentOS 5.5 Linux OS Classification: 3, 16.12 Nature of problem: Simulation of chemical systems, particularly with low species populations, can be accurately performed using Gillespie's method of stochastic simulation. Numerous variations on the original stochastic simulation algorithm have been developed, including approaches that produce results with statistics that exactly match the chemical master equation (CME) as well as other approaches that approximate the CME. Solution

Simulation and Digitization of a Gas Electron Multiplier Detector Using Geant4 and an Object-Oriented Digitization Program

Science.gov (United States)

McMullen, Timothy; Liyanage, Nilanga; Xiong, Weizhi; Zhao, Zhiwen

2017-01-01

Our research has focused on simulating the response of a Gas Electron Multiplier (GEM) detector using computational methods. GEM detectors provide a cost effective solution for radiation detection in high rate environments. A detailed simulation of GEM detector response to radiation is essential for the successful adaption of these detectors to different applications. Using Geant4 Monte Carlo (GEMC), a wrapper around Geant4 which has been successfully used to simulate the Solenoidal Large Intensity Device (SoLID) at Jefferson Lab, we are developing a simulation of a GEM chamber similar to the detectors currently used in our lab. We are also refining an object-oriented digitization program, which translates energy deposition information from GEMC into electronic readout which resembles the readout from our physical detectors. We have run the simulation with beta particles produced by the simulated decay of a 90Sr source, as well as with a simulated bremsstrahlung spectrum. Comparing the simulation data with real GEM data taken under similar conditions is used to refine the simulation parameters. Comparisons between results from the simulations and results from detector tests will be presented.

From bricks to buildings: adapting the Medical Research Council framework to develop programs of research in simulation education and training for the health professions.

Science.gov (United States)

Haji, Faizal A; Da Silva, Celina; Daigle, Delton T; Dubrowski, Adam

2014-08-01

Presently, health care simulation research is largely conducted on a study-by-study basis. Although such "project-based" research generates a plethora of evidence, it can be chaotic and contradictory. A move toward sustained, thematic, theory-based programs of research is necessary to advance knowledge in the field. Recognizing that simulation is a complex intervention, we present a framework for developing research programs in simulation-based education adapted from the Medical Research Council (MRC) guidance. This framework calls for an iterative approach to developing, refining, evaluating, and implementing simulation interventions. The adapted framework guidance emphasizes: (1) identification of theory and existing evidence; (2) modeling and piloting interventions to clarify active ingredients and identify mechanisms linking the context, intervention, and outcomes; and (3) evaluation of intervention processes and outcomes in both the laboratory and real-world setting. The proposed framework will aid simulation researchers in developing more robust interventions that optimize simulation-based education and advance our understanding of simulation pedagogy.

Desktop Modeling and Simulation: Parsimonious, yet Effective Discrete-Event Simulation Analysis

Science.gov (United States)

Bradley, James R.

2012-01-01

This paper evaluates how quickly students can be trained to construct useful discrete-event simulation models using Excel The typical supply chain used by many large national retailers is described, and an Excel-based simulation model is constructed of it The set of programming and simulation skills required for development of that model are then determined we conclude that six hours of training are required to teach the skills to MBA students . The simulation presented here contains all fundamental functionallty of a simulation model, and so our result holds for any discrete-event simulation model. We argue therefore that Industry workers with the same technical skill set as students having completed one year in an MBA program can be quickly trained to construct simulation models. This result gives credence to the efficacy of Desktop Modeling and Simulation whereby simulation analyses can be quickly developed, run, and analyzed with widely available software, namely Excel.

Medical Simulation Practices 2010 Survey Results

Science.gov (United States)

McCrindle, Jeffrey J.

2011-01-01

Medical Simulation Centers are an essential component of our learning infrastructure to prepare doctors and nurses for their careers. Unlike the military and aerospace simulation industry, very little has been published regarding the best practices currently in use within medical simulation centers. This survey attempts to provide insight into the current simulation practices at medical schools, hospitals, university nursing programs and community college nursing programs. Students within the MBA program at Saint Joseph's University conducted a survey of medical simulation practices during the summer 2010 semester. A total of 115 institutions responded to the survey. The survey resus discuss overall effectiveness of current simulation centers as well as the tools and techniques used to conduct the simulation activity

An Agent-Based Monetary Production Simulation Model

DEFF Research Database (Denmark)

Bruun, Charlotte

2006-01-01

An Agent-Based Simulation Model Programmed in Objective Borland Pascal. Program and source code is downloadable......An Agent-Based Simulation Model Programmed in Objective Borland Pascal. Program and source code is downloadable...

EGS code system: computer programs for the Monte Carlo simulation of electromagnetic cascade showers. Version 3

International Nuclear Information System (INIS)

Ford, R.L.; Nelson, W.R.

1978-06-01

A code to simulate almost any electron--photon transport problem conceivable is described. The report begins with a lengthy historical introduction and a description of the shower generation process. Then the detailed physics of the shower processes and the methods used to simulate them are presented. Ideas of sampling theory, transport techniques, particle interactions in general, and programing details are discussed. Next, EGS calculations and various experiments and other Monte Carlo results are compared. The remainder of the report consists of user manuals for EGS, PEGS, and TESTSR codes; options, input specifications, and typical output are included. 38 figures, 12 tables

Development of a hot water tank simulation program with improved prediction of thermal stratification in the tank

DEFF Research Database (Denmark)

Fan, Jianhua; Furbo, Simon; Yue, Hongqiang

2015-01-01

A simulation program SpiralSol was developed in previous investigations to calculate thermal performance of a solar domestic hot water (SDHW) system with a hot water tank with a built-in heat exchanger spiral [1]. The simulation program is improved in the paper in term of prediction of thermal...... stratification in the tank. The transient fluid flow and heat transfer in the hot water tank during cooling caused by standby heat loss are investigated by validated computational fluid dynamics (CFD) calculations. Detailed CFD investigations are carried out to determine the influence of thickness and material...... property of the tank wall on thermal stratification in the tank. It is elucidated how thermal stratification in the tank is influenced by the natural convection and how the heat loss from the tank sides will be distributed at different levels of the tank at different thermal conditions. The existing...

The pillars of well-constructed simulated patient programs: A qualitative study with experienced educators.

Science.gov (United States)

Pritchard, Shane A; Blackstock, Felicity C; Keating, Jennifer L; Nestel, Debra

2017-11-01

The inclusion of simulated patients (SPs) in health professional education is growing internationally. However, there is limited evidence for best practice in SP methodology. This study investigated how experienced SP educators support SPs in providing SP-based education for health professional students. Experienced SP educators were identified via relevant professional associations, peer-reviewed publications, and peer referral. Semi-structured individual interviews were conducted via telephone. Data were analyzed independently by three researchers using principles of inductive thematic analysis. Four themes were identified that represent the key structural components of SP programs considered by educators seeking to optimize learning for health professional students in SP programs: managing SPs by operationalizing an effective program, selecting SPs by rigorously screening for suitability, preparing SPs by educating for a specific scenario, and directing SPs by leading safe and meaningful interactions. Within these components, subthemes were described, with considerable variation in approaches. Key structural components to SP programs were consistently described by experienced SP educators who operationalize them. A framework has been proposed to assist educators in designing high-quality SP programs that support SPs and learners. Future research is required to evaluate and refine this framework and other evidence-based resources for SP educators.

SARDAN- A program for the transients simulation in a typical PWR plant

International Nuclear Information System (INIS)

Mattos Santos, R.L.P. de.

1979-10-01

A program in FORTRAN-IV language was developed that simulates the behaviour of the primary circuit in a typical PWR plant during condition II transients, in particular uncontrolled withdrawal of a control rod set, control rod set drops and uncontrolled boron dilution. It the mathematical model adopted the reactor core, the hot piping to which a pressurizer is coupled, the steam generator and the cold piping are considered. The results obtained in the analysis of the mentioned accidents are compared to those present at the Final Safety Analysis Report (FSAR) of the Angra-1 reactor and are considered satisfactory. (F.E.) [pt

Evaluation of an antimicrobial resistance monitoring program for campylobacter in poultry by simulation

DEFF Research Database (Denmark)

Regula, G.; Wong, Danilo Lo Fo; Ledergerber, U.

2005-01-01

An ideal national resistance monitoring program should deliver a precise estimate of the resistance situation for a given combination of bacteria and antimicrobial at a low cost. To achieve this, decisions need to be made on the number of samples to be collected at each of different possible...... sampling points. Existing methods of sample size calculation can not be used to solve this problem, because sampling decisions do not only depend on the prevalence of resistance and sensitivity and specificity of resistance testing, but also on the prevalence of the bacteria, and test characteristics...... of isolation of these bacteria. Our aim was to develop a stochastic simulation model that optimized a national resistance monitoring program, taking multi-stage sampling, imperfect sensitivity and specificity of diagnostic tests, and cost-effectiveness considerations into account. The process of resistance...

A research on applications of qualitative reasoning techniques in Human Acts Simulation Program

International Nuclear Information System (INIS)

Far, B.H.

1992-04-01

Human Acts Simulation Program (HASP) is a ten-year research project of the Computing and Information Systems Center of JAERI. In HASP the goal is developing programs for an advanced intelligent robot to accomplish multiple instructions (for instance, related to surveillance, inspection and maintenance) in nuclear power plants. Some recent artificial intelligence techniques can contribute to this project. This report introduces some original contributions concerning application of Qualitative Reasoning (QR) techniques in HASP. The focus is on the knowledge-intensive tasks, including model-based reasoning, analytic learning, fault diagnosis and functional reasoning. The multi-level extended qualitative modeling for the Skill-Rule-Knowledge (S-R-K) based reasoning, that included the coordination and timing of events, Qualitative Sensitivity analysis (Q S A), Subjective Qualitative Fault Diagnosis (S Q F D) and Qualitative Function Formation (Q F F ) techniques are introduced. (author) 123 refs

Disruption simulation experiments in a pulsed plasma accelerator - energy absorption and damage evolution on plasma facing materials

International Nuclear Information System (INIS)

Bolt, H.; Barabash, V.; Gervash, A.; Linke, J.; Lu, L.P.; Ovchinnikov, I.; Roedig, M.

1995-01-01

Plasma accelerators are used as test beds for disruption simulation experiments on plasma facing materials, because the incident energy fluxes and the discharge duration are of similar order as those expected during disruptions in ITER. The VIKA facility was used for the testing of materials under incident energies up to 5 kJ/cm 2 . Different carbon materials, SiC, stainless steel, TZM and tungsten have been tested. From the experimental results a scaling of the ablation with incident energy density was derived. The resulting ablation depth on carbon materials is roughly 2 μm per kJcm -2 of incident energy density. For metals this ablation is much higher due to the partial loss of the melt layer from splashing. For stainless steel an ablation depth of 9.5 μm per kJcm -2 was determined. The result of a linear scaling of the ablation depth with incident energy density is consistent with a previous calorimetric study. (orig.)

Simulation language of DSNP: dynamic simulator for nuclear power-plants

International Nuclear Information System (INIS)

Saphier, D.

1978-09-01

The Dynamic Simulator for Nuclear Power-plants (DSNP) is a system of programs and data sets by which a nuclear power plant or part thereof can be simulated at different levels of sophistication. The acronym DSNP is used interchangeably for the DSNP language, for the DSNP precompiler, for the DSNP libraries, and for the DSNP document generator. The DSNP language is a set of simple block oriented statements, which together with the appropriate data, comprise a simulation of a nuclear power plant. The majority of the DSNP statements will result in the inclusion of a simulated physical module into the program. FORTRAN statements can be inserted with no restrictions among DSNP statements

Program package for multicanonical simulations of U(1) lattice gauge theory-Second version

Science.gov (United States)

Bazavov, Alexei; Berg, Bernd A.

2013-03-01

A new version STMCMUCA_V1_1 of our program package is available. It eliminates compatibility problems of our Fortran 77 code, originally developed for the g77 compiler, with Fortran 90 and 95 compilers. New version program summaryProgram title: STMC_U1MUCA_v1_1 Catalogue identifier: AEET_v1_1 Licensing provisions: Standard CPC license, http://cpc.cs.qub.ac.uk/licence/licence.html Programming language: Fortran 77 compatible with Fortran 90 and 95 Computers: Any capable of compiling and executing Fortran code Operating systems: Any capable of compiling and executing Fortran code RAM: 10 MB and up depending on lattice size used No. of lines in distributed program, including test data, etc.: 15059 No. of bytes in distributed program, including test data, etc.: 215733 Keywords: Markov chain Monte Carlo, multicanonical, Wang-Landau recursion, Fortran, lattice gauge theory, U(1) gauge group, phase transitions of continuous systems Classification: 11.5 Catalogue identifier of previous version: AEET_v1_0 Journal Reference of previous version: Computer Physics Communications 180 (2009) 2339-2347 Does the new version supersede the previous version?: Yes Nature of problem: Efficient Markov chain Monte Carlo simulation of U(1) lattice gauge theory (or other continuous systems) close to its phase transition. Measurements and analysis of the action per plaquette, the specific heat, Polyakov loops and their structure factors. Solution method: Multicanonical simulations with an initial Wang-Landau recursion to determine suitable weight factors. Reweighting to physical values using logarithmic coding and calculating jackknife error bars. Reasons for the new version: The previous version was developed for the g77 compiler Fortran 77 version. Compiler errors were encountered with Fortran 90 and Fortran 95 compilers (specified below). Summary of revisions: epsilon=one/10**10 is replaced by epsilon/10.0D10 in the parameter statements of the subroutines u1_bmha.f, u1_mucabmha.f, u1wl

An Intelligent Robot Programing

Energy Technology Data Exchange (ETDEWEB)

Hong, Seong Yong

2012-01-15

This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

An Intelligent Robot Programing

International Nuclear Information System (INIS)

Hong, Seong Yong

2012-01-01

This book introduces an intelligent robot programing with background of the begging, introduction of VPL, and SPL, building of environment for robot platform, starting of robot programing, design of simulation environment, robot autonomy drive control programing, simulation graphic. Such as SPL graphic programing graphical image and graphical shapes, and graphical method application, application of procedure for robot control, robot multiprogramming, robot bumper sensor programing, robot LRF sencor programing and robot color sensor programing.

A Simple Spreadsheet Program to Simulate and Analyze the Far-UV Circular Dichroism Spectra of Proteins

Science.gov (United States)

Abriata, Luciano A.

2011-01-01

A simple algorithm was implemented in a spreadsheet program to simulate the circular dichroism spectra of proteins from their secondary structure content and to fit [alpha]-helix, [beta]-sheet, and random coil contents from experimental far-UV circular dichroism spectra. The physical basis of the method is briefly reviewed within the context of…

Implementation and evaluation of an interprofessional simulation-based education program for undergraduate nursing students in operating room nursing education: a randomized controlled trial.

Science.gov (United States)

Wang, Rongmei; Shi, Nianke; Bai, Jinbing; Zheng, Yaguang; Zhao, Yue

2015-07-09

The present study was designed to implement an interprofessional simulation-based education program for nursing students and evaluate the influence of this program on nursing students' attitudes toward interprofessional education and knowledge about operating room nursing. Nursing students were randomly assigned to either the interprofessional simulation-based education or traditional course group. A before-and-after study of nursing students' attitudes toward the program was conducted using the Readiness for Interprofessional Learning Scale. Responses to an open-ended question were categorized using thematic content analysis. Nursing students' knowledge about operating room nursing was measured. Nursing students from the interprofessional simulation-based education group showed statistically different responses to four of the nineteen questions in the Readiness for Interprofessional Learning Scale, reflecting a more positive attitude toward interprofessional learning. This was also supported by thematic content analysis of the open-ended responses. Furthermore, nursing students in the simulation-based education group had a significant improvement in knowledge about operating room nursing. The integrated course with interprofessional education and simulation provided a positive impact on undergraduate nursing students' perceptions toward interprofessional learning and knowledge about operating room nursing. Our study demonstrated that this course may be a valuable elective option for undergraduate nursing students in operating room nursing education.

Cardiovascular Surgery Residency Program: Training Coronary Anastomosis Using the Arroyo Simulator and UNIFESP Models.

Science.gov (United States)

Maluf, Miguel Angel; Gomes, Walter José; Bras, Ademir Massarico; Araújo, Thiago Cavalcante Vila Nova de; Mota, André Lupp; Cardoso, Caio Cesar; Coutinho, Rafael Viana dos S

2015-01-01

Engage the UNIFESP Cardiovascular Surgery residents in coronary anastomosis, assess their skills and certify results, using the Arroyo Anastomosis Simulator and UNIFESP surgical models. First to 6th year residents attended a weekly program of technical training in coronary anastomosis, using 4 simulation models: 1. Arroyo simulator; 2. Dummy with a plastic heart; 3. Dummy with a bovine heart; and 4. Dummy with a beating pig heart. The assessment test was comprised of 10 items, using a scale from 1 to 5 points in each of them, creating a global score of 50 points maximum. The technical performance of the candidate showed improvement in all items, especially manual skill and technical progress, critical sense of the work performed, confidence in the procedure and reduction of the time needed to perform the anastomosis after 12 weeks practice. In response to the multiplicity of factors that currently influence the cardiovascular surgeon training, there have been combined efforts to reform the practices of surgical medical training. 1 - The four models of simulators offer a considerable contribution to the field of cardiovascular surgery, improving the skill and dexterity of the surgeon in training. 2 - Residents have shown interest in training and cooperate in the development of innovative procedures for surgical medical training in the art.

Studying Turbulence Using Numerical Simulation Databases. No. 7; Proceedings of the Summer Program

Science.gov (United States)

1998-01-01

The Seventh Summer Program of the Center for Turbulence Research took place in the four-week period, July 5 to July 31, 1998. This was the largest CTR Summer Program to date, involving thirty-six participants from the U. S. and nine other countries. Thirty-one Stanford and NASA-Ames staff members facilitated and contributed to most of the Summer projects. A new feature, and perhaps a preview of the future programs, was that many of the projects were executed on non-NASA computers. These included supercomputers located in Europe as well as those operated by the Departments of Defense and Energy in the United States. In addition, several simulation programs developed by the visiting participants at their home institutions were used. Another new feature was the prevalence of lap-top personal computers which were used by several participants to carry out some of the work that in the past were performed on desk-top workstations. We expect these trends to continue as computing power is enhanced and as more researchers (many of whom CTR alumni) use numerical simulations to study turbulent flows. CTR's main role continues to be in providing a forum for the study of turbulence for engineering analysis and in facilitating intellectual exchange among the leading researchers in the field. Once again the combustion group was the largest. Turbulent combustion has enjoyed remarkable progress in using simulations to address increasingly complex and practically more relevant questions. The combustion group's studies included such challenging topics as fuel evaporation, soot chemistry, and thermonuclear reactions. The latter study was one of three projects related to the Department of Energy's ASCI Program (www.llnl.gov/asci); the other two (rocket propulsion and fire safety) were carried out in the turbulence modeling group. The flow control and acoustics group demonstrated a successful application of the so-called evolution algorithms which actually led to a previously unknown

Simulation of CIFF (Centralized IFF) remote control displays

Science.gov (United States)

Tucker, D. L.; Leibowitz, L. M.

1986-06-01

This report presents the software simulation of the Remote-Control-Display (RCS) proposed to be used in the Centralized IFF (CIFF) system. A description of the simulation programs along with simulated menu formats are presented. A sample listing of the simulation programs and a brief description of the program operation are also included.

Significant differences. What owners of photovoltaic plants should know about simulation programs; Deutliche Unterschiede. Was man als Anlagenbetreiber ueber Simulationsprogramme wissen sollte

Energy Technology Data Exchange (ETDEWEB)

Podewils, Christoph

2011-04-15

Owners of photovoltaic plants are naturally most interested in the solar gain that is to be expected. Simulation programs can answer this question. Their results vary from product to product, so it is recommended to use more than one program.

Development and evaluation of a simulator-based laparoscopic training program for surgical novices.

Science.gov (United States)

Nugent, Emmeline; Shirilla, Nicole; Hafeez, Adnan; O'Riordain, Diarmuid S; Traynor, Oscar; Harrison, Anthony M; Neary, Paul

2013-01-01

The use of simulation to train novice surgeons in laparoscopic skills is becoming increasingly popular. To maximize benefit from simulation, training needs to be delivered and assessed in a structured manner. This study aimed to define performance goals, demonstrate construct validity of the training program, and evaluate whether novice surgeons could reach the preset performance goals. Nine expert laparoscopic surgeons established performance goals for three basic modules of an augmented-reality laparoscopic simulator. The three laparoscopic modules were used by 40 novice surgeons and 40 surgical trainees (postgraduate years [PGYs] 1-4). The performance outcomes were analyzed across the different groups (novice, PGYs 1 and 2, PGYs 3 and 4, expert) to determine construct validity. Then 26 recruited novices trained on the three modules with the aim of reaching the performance goals. The results demonstrated a significant difference in performance between all levels of experience for time (p < 0.001), motion analysis (p < 0.001), and error score (p < 0.001), thus demonstrating construct validity. All 26 novice surgeons significantly improved in performance with repetition for the metrics of time (p < 0.001) and motion analysis (p < 0.001). For two of the modules, the proficiency goals were reached in fewer than 10 trials by 80% of the study participants. Basic skills in laparoscopic surgery can be learned and improved using proficiency-based simulation training. It is possible for novice surgeons to achieve predefined performance goals in a reasonable time frame.

Simulation of trickle irrigation, an extension to the US Geological Survey's computer program VS2D

Science.gov (United States)

Healy, R.W.

1987-01-01

A method is presented for simulating water movement through unsaturated porous media in response to a constant rate of application from a surface source. Because the rate at which water can be absorbed by soil is limited, the water will pond; therefore the actual surface area over which the water is applied may change with time and in general will not be known beforehand. An iterative method is used to determine the size of this ponded area at any time. This method will be most useful for simulating trickling irrigation, but also may be of value for simulating movement of water is soils as the result of an accidental spill. The method is an extension to the finite difference computer program VS2D developed by the U.S. Geological Survey, which simulates water movement through variably saturated porous media. The simulated region can be a vertical, 2-dimensional cross section for treatment of a surface line source or an axially symmetric, 3-dimensional cylinder for a point source. Five test problems, obtained from the literature , are used to demonstrate the ability of the method to accurately match analytical and experimental results. (Author 's abstract)

The Effect of Model Fidelity on Learning Outcomes of a Simulation-Based Education Program for Central Venous Catheter Insertion.

Science.gov (United States)

Diederich, Emily; Mahnken, Jonathan D; Rigler, Sally K; Williamson, Timothy L; Tarver, Stephen; Sharpe, Matthew R

2015-12-01

Simulation-based education for central venous catheter (CVC) insertion has been repeatedly documented to improve performance, but the impact of simulation model fidelity has not been described. The aim of this study was to examine the impact of the physical fidelity of the simulation model on learning outcomes for a simulation-based education program for CVC insertion. Forty consecutive residents rotating through the medical intensive care unit of an academic medical center completed a simulation-based education program for CVC insertion. The curriculum was designed in accordance with the principles of deliberate practice and mastery learning. Each resident underwent baseline skills testing and was then randomized to training on a commercially available CVC model with high physical fidelity (High-Fi group) or a simply constructed model with low physical fidelity (Low-Fi group) in a noninferiority trial. Upon completion of their medical intensive care unit rotation 4 weeks later, residents returned for repeat skills testing on the high-fidelity model using a 26-item checklist. The mean (SD) posttraining score on the 26-item checklist for the Low-Fi group was 23.8 (2.2) (91.5%) and was not inferior to the mean (SD) score for the High-Fi group of 22.5 (2.6) (86.5%) (P Simulation-based education using equipment with low physical fidelity can achieve learning outcomes comparable with those with high-fidelity equipment, as long as other aspects of fidelity are maintained and robust educational principles are applied during the design of the curriculum.

Cooperation in simulating a pressurized coal dust reactor with different simulation programs; Kooperation bei der Simulation eines Druckkohlenstaubreaktors mit unterschiedlichen Simulationsprogrammen

Energy Technology Data Exchange (ETDEWEB)

Ayar, A.; Hecken, M. [Technische Hochschule Aachen (Germany). Lehrstuhl fuer Waermeuebertragung und Klimatechnik; Mohr, M.; Murza, S. [Bochum Univ. (Germany). Lehrstuhl fuer Energieanlagentechnik; Richter, S.; Stroehle, J. [Stuttgart Univ. (Germany). Inst. fuer Verfahrenstechnik und Dampfkesselwesen

1999-09-01

The contribution presents the results of a cooperative project of three different universities - Department of Heat Transfer and Air Conditioning Engineering (WUeK) of RWTH Aachen, Department of Power Sytems Engineering (LEAT) of Ruhr-Universitaet Bochum, Institute of Chemical Engineering and Steam Boiler Engineering (IVD) of Stuttgart University - which involved modellilng a benchmark flame of the pressurized coal dust reactor of the Departmentof Heat Transfer and Air Conditioning Engineering. The conditions of the benchmark flame reflect a real firnace condition which so far has never been investigated experimentally. The contribution compares the results of the three different simulation programs and presents an outlook to the necessary further developments of the programs for modelling plants for pressurized coal dust combustion. [Deutsch] Es werden die Ergebnisse der Zusammenarbeit der drei beteiligten Institute - Lehrstuhl fuer Waermeuebertragung und Klimatechnik (WUeK) der RWTH Aachen, Lehrstuhl fuer Energieanlagentechnik (LEAT) der Ruhr-Uni Bochum und Institut fuer Verfahrenstechnik und Dampfkesselwesen (IVD) der Uni Stuttgart - bei der Modellierung einer Benchmarkflamme des Druckkohlenstaubreaktors am Lehrstuhl fuer Waermeuebertragung und Klimatechnik dargestellt. Diese Bedingungen fuer diese Benchmarkflamme sind einem realen, bis dato noch nicht experimentell untersuchten Feuerungszustand nachempfunden. Der Beitrag beinhaltet den Vergleich der mit drei unterschiedlichen Simulationsprogrammen erzielten Ergebnisse und gibt einen Ausblick auf die notwendigen Weiterentwicklungen der Programme hinsichtlich der Modellierung druckkohlenstaubgefeuerter Anlagen. (orig.)

40 CFR 180.108 - Acephate; tolerances for residues.

Science.gov (United States)

2010-07-01

... establishments, including food service, manufacturing and processing establishments, such as restaurants... avoid atomization or splashing of the spray. Contamination of food or food-contact surfaces shall be... PROGRAMS TOLERANCES AND EXEMPTIONS FOR PESTICIDE CHEMICAL RESIDUES IN FOOD Specific Tolerances § 180.108...

Simulation and off-line programming at Sandia`s Intelligent Systems and Robotics Center

Energy Technology Data Exchange (ETDEWEB)

Xavier, P.G.; Fahrenholtz, J.C.; McDonald, M. [Sandia National Labs., Albuquerque, NM (United States). Intelligent Systems and Robotics Center] [and others

1997-11-01

One role of the Intelligent Robotics and System Center (ISRC) at Sandia National Laboratories is to address certain aspects of Sandia`s mission to design, manufacture, maintain, and dismantle nuclear weapon components. Hazardous materials, devices, and environments are often involved. Because of shrinking resources, these tasks must be accomplished with a minimum of prototyping, while maintaining high reliability. In this paper, the authors describe simulation, off-line programming/planning, and related tools which are in use, under development, and being researched to solve these problems at the ISRC.

GROSS- GAMMA RAY OBSERVATORY ATTITUDE DYNAMICS SIMULATOR

Science.gov (United States)

Garrick, J.

1994-01-01

The Gamma Ray Observatory (GRO) spacecraft will constitute a major advance in gamma ray astronomy by offering the first opportunity for comprehensive observations in the range of 0.1 to 30,000 megaelectronvolts (MeV). The Gamma Ray Observatory Attitude Dynamics Simulator, GROSS, is designed to simulate this mission. The GRO Dynamics Simulator consists of three separate programs: the Standalone Profile Program; the Simulator Program, which contains the Simulation Control Input/Output (SCIO) Subsystem, the Truth Model (TM) Subsystem, and the Onboard Computer (OBC) Subsystem; and the Postprocessor Program. The Standalone Profile Program models the environment of the spacecraft and generates a profile data set for use by the simulator. This data set contains items such as individual external torques; GRO spacecraft, Tracking and Data Relay Satellite (TDRS), and solar and lunar ephemerides; and star data. The Standalone Profile Program is run before a simulation. The SCIO subsystem is the executive driver for the simulator. It accepts user input, initializes parameters, controls simulation, and generates output data files and simulation status display. The TM subsystem models the spacecraft dynamics, sensors, and actuators. It accepts ephemerides, star data, and environmental torques from the Standalone Profile Program. With these and actuator commands from the OBC subsystem, the TM subsystem propagates the current state of the spacecraft and generates sensor data for use by the OBC and SCIO subsystems. The OBC subsystem uses sensor data from the TM subsystem, a Kalman filter (for attitude determination), and control laws to compute actuator commands to the TM subsystem. The OBC subsystem also provides output data to the SCIO subsystem for output to the analysts. The Postprocessor Program is run after simulation is completed. It generates printer and CRT plots and tabular reports of the simulated data at the direction of the user. GROSS is written in FORTRAN 77 and

Perceived Barriers to the Use of High-Fidelity Hands-On Simulation Training for Contrast Reaction Management: Why Programs are Not Using It.

Science.gov (United States)

Chinnugounder, Sankar; Hippe, Daniel S; Maximin, Suresh; O'Malley, Ryan B; Wang, Carolyn L

2015-01-01

Although subjective and objective benefits of high-fidelity simulation have been reported in medicine, there has been slow adoption in radiology. The purpose of our study was to identify the perceived barriers in the use of high-fidelity hands-on simulation for contrast reaction management training. An IRB exempt 32 questions online web survey was sent to 179 non-military radiology residency program directors listed in the Fellowship and Residency Electronic Interactive Database Access system (FREIDA). Survey questions included the type of contrast reaction management training, cost, time commitment of residents and faculty, and the reasons for not using simulation training. Responses from the survey were summarized as count (percentage), mean ± standard deviation (SD), or median (range). 84 (47%) of 179 programs responded, of which 88% offered CRM training. Most (72%) conducted the CRM training annually while only 4% conducted it more frequently. Didactic lecture was the most frequently used training modality (97%), followed by HFS (30%) and computer-based simulation (CBS) (19%); 5.5% used both HFS and CBS. Of the 51 programs that offer CRM training but do not use HFS, the most common reason reported was insufficient availability (41%). Other reported reasons included cost (33%), no access to simulation centers (33%), lack of trained faculty (27%) and time constraints (27%). Although high-fidelity hands-on simulation training is the best way to reproduce real-life contrast reaction scenarios, many institutions do not provide this training due to constraints such as cost, lack of access or insufficient availability of simulation labs, and lack of trained faculty. As a specialty, radiology needs to better address these barriers at both an institutional and national level. Copyright © 2015 Mosby, Inc. All rights reserved.

Experiential learning: using virtual simulation in an online RN-to-BSN program.

Science.gov (United States)

Breen, Henny; Jones, Melissa

2015-01-01

This article highlights the innovative experiential learning used by an online RN-to-BSN program through the use of simulation that takes place in an online classroom. Three experiential learning activities using a virtual community are described. These learning activities engage the students in thinking about social justice and health policy, as well as teaching concepts that include community, leadership, influence, advocacy, networking, collaboration, and vulnerable populations. These concepts are critical to the learning needs of diploma and associate degree-prepared nurses who wish to continue their education to be better prepared to meet the complex needs of today's health care environment. Copyright 2015, SLACK Incorporated.

Simulation of Darlington shutdown and regulation systems

International Nuclear Information System (INIS)

1986-10-01

This report describes the development of a simulation of the Darlington Nuclear Generating Station shutdown and regulating systems, DARSIM. The DARSIM program simulates the spatial neutron dynamics, the regulation of the reactor power, and Shutdown System 1, SDS1, and Shutdown System 2, SDS2, software. The DARSIM program operates in the interactive simulation (INSIM) program environment

Waves Generated by Asteroid Impacts and Their Hazard Consequences on The Shorelines

Science.gov (United States)

Ezzedine, S. M.; Miller, P. L.; Dearborn, D. S.

2014-12-01

We have performed numerical simulations of a hypothetical asteroid impact onto the ocean in support of an emergency preparedness, planning, and management exercise. We addressed the scenario from asteroid entry; to ocean impact (splash rim); to wave generation, propagation, and interaction with the shoreline. For the analysis we used GEODYN, a hydrocode, to simulate the impact and generate the source wave for the large-scale shallow water wave program, SWWP. Using state-of-the-art, high-performance computing codes we simulated three impact areas — two are located on the West Coast near Los Angeles's shoreline and the San Francisco Bay, respectively, and the third is located in the Gulf of Mexico, with a possible impact location between Texas and Florida. On account of uncertainty in the exact impact location within the asteroid risk corridor, we examined multiple possibilities for impact points within each area. Uncertainty in the asteroid impact location was then convolved and represented as uncertainty in the shoreline flooding zones. This work performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344, and partially funded by the Laboratory Directed Research and Development Program at LLNL under tracking code 12-ERD-005.

Systemic Analysis, Mapping, Modeling, and Simulation of the Advanced Accelerator Applications Program

International Nuclear Information System (INIS)

Guan, Yue; Laidler, James J.; Morman, James A.

2002-01-01

Advanced chemical separations methods envisioned for use in the Department of Energy Advanced Accelerator Applications (AAA) program have been studied using the Systemic Analysis, Mapping, Modeling, and Simulation (SAMMS) method. This integrated and systematic method considers all aspects of the studied process as one dynamic and inter-dependent system. This particular study focuses on two subjects: the chemical separation processes for treating spent nuclear fuel, and the associated non-proliferation implications of such processing. Two levels of chemical separation models are developed: level 1 models treat the chemical process stages by groups; and level 2 models depict the details of each process stage. Models to estimate the proliferation risks based on proliferation barrier assessment are also developed. This paper describes the research conducted for the single-stratum design in the AAA program. Further research conducted for the multi-strata designs will be presented later. The method and models described in this paper can help in the design of optimized processes that fulfill the chemical separation process specifications and non-proliferation requirements. (authors)

Improving Nurses' Peripheral Intravenous Catheter Insertion Knowledge, Confidence, and Skills Using a Simulation-Based Blended Learning Program: A Randomized Trial.

Science.gov (United States)

Keleekai, Nowai L; Schuster, Catherine A; Murray, Connie L; King, Mary Anne; Stahl, Brian R; Labrozzi, Laura J; Gallucci, Susan; LeClair, Matthew W; Glover, Kevin R

2016-12-01

Peripheral intravenous catheter (PIVC) insertion is one of the most common invasive procedures performed in a hospital, but most nurses receive little formal training in this area. Blended PIVC insertion training programs that incorporate deliberate simulated practice have the potential to improve clinical practice and patient care. The study was a randomized, wait-list control group with crossover using nurses on three medical/surgical units. Baseline PIVC knowledge, confidence, and skills assessments were completed for both groups. The intervention group then received a 2-hour PIVC online course, followed by an 8-hour live training course using a synergistic mix of three simulation tools. Both groups were then reassessed. After crossover, the wait-list group received the same intervention and both groups were reassessed. At baseline, both groups were similar for knowledge, confidence, and skills. Compared with the wait-list group, the intervention group had significantly higher scores for knowledge, confidence, and skills upon completing the training program. After crossover, the wait-list group had similarly higher scores for knowledge, confidence, and skills than the intervention group. Between the immediate preintervention and postintervention periods, the intervention group improved scores for knowledge by 31%, skills by 24%, and decreased confidence by 0.5%, whereas the wait-list group improved scores for knowledge by 28%, confidence by 16%, and skills by 15%. Results demonstrate significant improvements in nurses' knowledge, confidence, and skills with the use of a simulation-based blended learning program for PIVC insertion. Transferability of these findings from a simulated environment into clinical practice should be further explored.

Powderspec, a program for the efficient simulation of spectra of electron paramagnetic resonance of powders with orthorhombic symmetry

International Nuclear Information System (INIS)

Gonzalez T, L.; Beltran L, V.

1991-09-01

In this report a FORTRAN source program which simulates the second order powder pattern and spectrum of electron paramagnetic resonance (EPR) in crystal fields with orthorhombic symmetry using Gauss-Legendre quadratures is given. Also the commentaries which describe each step in detail are presented. (Author)

Simulation Use in Paramedic Education Research (SUPER): A Descriptive Study.

Science.gov (United States)

McKenna, Kim D; Carhart, Elliot; Bercher, Daniel; Spain, Andrew; Todaro, John; Freel, Joann

2015-01-01

The purpose of this research was to characterize the use of simulation in initial paramedic education programs in order assist stakeholders' efforts to target educational initiatives and resources. This group sought to provide a snapshot of what simulation resources programs have or have access to and how they are used; faculty perceptions about simulation; whether program characteristics, resources, or faculty training influence simulation use; and if simulation resources are uniform for patients of all ages. This was a cross-sectional census survey of paramedic programs that were accredited or had a Letter of Review from the Committee on Accreditation of Educational Programs for the EMS Professions at the time of the study. The data were analyzed using descriptive statistics and chi-square analyses. Of the 638 surveys sent, 389 valid responses (61%) were analyzed. Paramedic programs reported they have or have access to a wide range of simulation resources (task trainers [100%], simple manikins [100%], intermediate manikins [99%], advanced/fully programmable manikins [91%], live simulated patients [83%], computer-based [71%], and virtual reality [19%]); however, they do not consistently use them, particularly advanced (71%), live simulated patients (66%), computer-based (games, scenarios) (31%), and virtual reality (4%). Simulation equipment (of any type) reportedly sits idle and unused in (31%) of programs. Lack of training was cited as the most common reason. Personnel support specific to simulation was available in 44% of programs. Programs reported using simulation to replace skills more frequently than to replace field or clinical hours. Simulation goals included assessment, critical thinking, and problem-solving most frequently, and patient and crew safety least often. Programs using advanced manikins report manufacturers as their primary means of training (87%) and that 19% of faculty had no training specific to those manikins. Many (78%) respondents felt

Modification of the RTMTRACE program for numerical simulation of particle dynamics at racetrack microtrons with account of space charge forces

International Nuclear Information System (INIS)

Surma, I.V.; Shvedunov, V.I.

1993-01-01

The paper presents modification results of the program for simulation of particle dynamics in cyclic accelerators with RTMTRACE linear gap. The program was modified with regard for the effect of space charge effect on particle dynamics. Calculation results of particle dynamics in 1 MeV energy continuous-duty accelerator with 10 kw beam were used to develop continuous powerful commercial accelerator. 3 refs., 2 figs

Budget Impact Analysis of Switching to Digital Mammography in a Population-Based Breast Cancer Screening Program: A Discrete Event Simulation Model

Science.gov (United States)

Comas, Mercè; Arrospide, Arantzazu; Mar, Javier; Sala, Maria; Vilaprinyó, Ester; Hernández, Cristina; Cots, Francesc; Martínez, Juan; Castells, Xavier

2014-01-01

Objective To assess the budgetary impact of switching from screen-film mammography to full-field digital mammography in a population-based breast cancer screening program. Methods A discrete-event simulation model was built to reproduce the breast cancer screening process (biennial mammographic screening of women aged 50 to 69 years) combined with the natural history of breast cancer. The simulation started with 100,000 women and, during a 20-year simulation horizon, new women were dynamically entered according to the aging of the Spanish population. Data on screening were obtained from Spanish breast cancer screening programs. Data on the natural history of breast cancer were based on US data adapted to our population. A budget impact analysis comparing digital with screen-film screening mammography was performed in a sample of 2,000 simulation runs. A sensitivity analysis was performed for crucial screening-related parameters. Distinct scenarios for recall and detection rates were compared. Results Statistically significant savings were found for overall costs, treatment costs and the costs of additional tests in the long term. The overall cost saving was 1,115,857€ (95%CI from 932,147 to 1,299,567) in the 10th year and 2,866,124€ (95%CI from 2,492,610 to 3,239,638) in the 20th year, representing 4.5% and 8.1% of the overall cost associated with screen-film mammography. The sensitivity analysis showed net savings in the long term. Conclusions Switching to digital mammography in a population-based breast cancer screening program saves long-term budget expense, in addition to providing technical advantages. Our results were consistent across distinct scenarios representing the different results obtained in European breast cancer screening programs. PMID:24832200

Simulation of a combined-cycle engine

Science.gov (United States)

Vangerpen, Jon

1991-01-01

A FORTRAN computer program was developed to simulate the performance of combined-cycle engines. These engines combine features of both gas turbines and reciprocating engines. The computer program can simulate both design point and off-design operation. Widely varying engine configurations can be evaluated for their power, performance, and efficiency as well as the influence of altitude and air speed. Although the program was developed to simulate aircraft engines, it can be used with equal success for stationary and automative applications.

simulate_CAT: A Computer Program for Post-Hoc Simulation for Computerized Adaptive Testing

Directory of Open Access Journals (Sweden)

İlker Kalender

2015-06-01

Full Text Available This paper presents a computer software developed by the author. The software conducts post-hoc simulations for computerized adaptive testing based on real responses of examinees to paper and pencil tests under different parameters that can be defined by user. In this paper, short information is given about post-hoc simulations. After that, the working principle of the software is provided and a sample simulation with required input files is shown. And last, output files are described