Auralization of airborne sound insulation including the influence of source room

DEFF Research Database (Denmark)

Rindel, Jens Holger

2006-01-01

The paper describes a simple and acoustically accurate method for the auralization of airborne sound insulation between two rooms by means of a room acoustic simulation software (ODEON). The method makes use of a frequency independent transparency of the transmitting surface combined...... with a frequency dependent power setting of the source in the source room. The acoustic properties in terms of volume and reverberation time as well as the area of the transmitting surface are all included in the simulation. The user only has to select the position of the source in the source room and the receiver...... of the transmitting surface is used for the simulation of sound transmission. Also the reduced clarity of the auralization due to the reverberance of the source room is inherent in the method. Currently the method is restricted to transmission loss data in octave bands....

A large angle cold neutron bender using sequential garland reflections for pulsed neutron source

Energy Technology Data Exchange (ETDEWEB)

Ebisawa, T.; Tasaki, S. [Kyoto Univ., Kumatori, Osaka (Japan). Research Reactor Inst; Soyama, K.; Suzuki, J. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2001-03-01

We discuss a basic structure and performance of a new cold neutron bender using sequential garland reflections, in order to bend a neutron beam with large divergence by large angle. Using this bender for a pulsed neutron source we could not only avoid the frame overlap for cold neutrons but also install a plural spectrometers at a cold guide and obtain polarized neutron beams if necessary. (author)

A large angle cold neutron bender using sequential garland reflections for pulsed neutron source

International Nuclear Information System (INIS)

Ebisawa, T.; Tasaki, S.; Soyama, K.; Suzuki, J.

2001-01-01

We discuss a basic structure and performance of a new cold neutron bender using sequential garland reflections, in order to bend a neutron beam with large divergence by large angle. Using this bender for a pulsed neutron source we could not only avoid the frame overlap for cold neutrons but also install a plural spectrometers at a cold guide and obtain polarized neutron beams if necessary. (author)

Guided wave imaging of oblique reflecting interfaces in pipes using common-source synthetic focusing

Science.gov (United States)

Sun, Zeqing; Sun, Anyu; Ju, Bing-Feng

2018-04-01

Cross-mode-family mode conversion and secondary reflection of guided waves in pipes complicate the processing of guided waves signals, and can cause false detection. In this paper, filters operating in the spectral domain of wavenumber, circumferential order and frequency are designed to suppress the signal components of unwanted mode-family and unwanted traveling direction. Common-source synthetic focusing is used to reconstruct defect images from the guided wave signals. Simulations of the reflections from linear oblique defects and a semicircle defect are separately implemented. Defect images, which are reconstructed from the simulation results under different excitation conditions, are comparatively studied in terms of axial resolution, reflection amplitude, detectable oblique angle and so on. Further, the proposed method is experimentally validated by detecting linear cracks with various oblique angles (10-40°). The proposed method relies on the guided wave signals that are captured during 2-D scanning of a cylindrical area on the pipe. The redundancy of the signals is analyzed to reduce the time-consumption of the scanning process and to enhance the practicability of the proposed method.

77 FR 6463 - Revisions to Labeling Requirements for Blood and Blood Components, Including Source Plasma...

Science.gov (United States)

2012-02-08

... Blood Components, Including Source Plasma; Correction AGENCY: Food and Drug Administration, HHS. ACTION..., Including Source Plasma,'' which provided incorrect publication information regarding a 60-day notice that...

Can a one-layer optical skin model including melanin and inhomogeneously distributed blood explain spatially resolved diffuse reflectance spectra?

Science.gov (United States)

Karlsson, Hanna; Pettersson, Anders; Larsson, Marcus; Strömberg, Tomas

2011-02-01

Model based analysis of calibrated diffuse reflectance spectroscopy can be used for determining oxygenation and concentration of skin chromophores. This study aimed at assessing the effect of including melanin in addition to hemoglobin (Hb) as chromophores and compensating for inhomogeneously distributed blood (vessel packaging), in a single-layer skin model. Spectra from four humans were collected during different provocations using a twochannel fiber optic probe with source-detector separations 0.4 and 1.2 mm. Absolute calibrated spectra using data from either a single distance or both distances were analyzed using inverse Monte Carlo for light transport and Levenberg-Marquardt for non-linear fitting. The model fitting was excellent using a single distance. However, the estimated model failed to explain spectra from the other distance. The two-distance model did not fit the data well at either distance. Model fitting was significantly improved including melanin and vessel packaging. The most prominent effect when fitting data from the larger separation compared to the smaller separation was a different light scattering decay with wavelength, while the tissue fraction of Hb and saturation were similar. For modeling spectra at both distances, we propose using either a multi-layer skin model or a more advanced model for the scattering phase function.

76 FR 62451 - Avon Products, Inc., Including On-Site Leased Workers From Spherion/Source Right, Springdale...

Science.gov (United States)

2011-10-07

...., Including On-Site Leased Workers From Spherion/Source Right, Springdale, Ohio; Amended Certification... workers of the subject firm. The company reports that workers leased from Spherion/Source Right were...., including on-site leased workers from Spherion/Source Right, Springdale, Ohio, who became totally or...

Polarization-based index of refraction and reflection angle estimation for remote sensing applications

Science.gov (United States)

Thilak, Vimal; Voelz, David G.; Creusere, Charles D.

2007-10-01

A passive-polarization-based imaging system records the polarization state of light reflected by objects that are illuminated with an unpolarized and generally uncontrolled source. Such systems can be useful in many remote sensing applications including target detection, object segmentation, and material classification. We present a method to jointly estimate the complex index of refraction and the reflection angle (reflected zenith angle) of a target from multiple measurements collected by a passive polarimeter. An expression for the degree of polarization is derived from the microfacet polarimetric bidirectional reflectance model for the case of scattering in the plane of incidence. Using this expression, we develop a nonlinear least-squares estimation algorithm for extracting an apparent index of refraction and the reflection angle from a set of polarization measurements collected from multiple source positions. Computer simulation results show that the estimation accuracy generally improves with an increasing number of source position measurements. Laboratory results indicate that the proposed method is effective for recovering the reflection angle and that the estimated index of refraction provides a feature vector that is robust to the reflection angle.

Bright Single-Photon Sources Based on Anti-Reflection Coated Deterministic Quantum Dot Microlenses

Directory of Open Access Journals (Sweden)

Peter Schnauber

2015-12-01

Full Text Available We report on enhancing the photon-extraction efficiency (PEE of deterministic quantum dot (QD microlenses via anti-reflection (AR coating. The AR-coating deposited on top of the curved microlens surface is composed of a thin layer of Ta2O5, and is found to effectively reduce back-reflection of light at the semiconductor-vacuum interface. A statistical analysis of spectroscopic data reveals, that the AR-coating improves the light out-coupling of respective microlenses by a factor of 1.57 ± 0.71, in quantitative agreement with numerical calculations. Taking the enhancement factor into account, we predict improved out-coupling of light with a PEE of up to 50%. The quantum nature of emission from QDs integrated into AR-coated microlenses is demonstrated via photon auto-correlation measurements revealing strong suppression of two-photon emission events with g(2(0 = 0.05 ± 0.02. As such, these bright non-classical light sources are highly attractive with respect to applications in the field of quantum cryptography.

Weak reward source memory in depression reflects blunted activation of VTA/SN and parahippocampus.

Science.gov (United States)

Dillon, Daniel G; Dobbins, Ian G; Pizzagalli, Diego A

2014-10-01

Reward responses in the medial temporal lobes and dopaminergic midbrain boost episodic memory formation in healthy adults, and weak memory for emotionally positive material in depression suggests this mechanism may be dysfunctional in major depressive disorder (MDD). To test this hypothesis, we performed a study in which unmedicated adults with MDD and healthy controls encoded drawings paired with reward or zero tokens during functional magnetic resonance imaging. In a recognition test, participants judged whether drawings were previously associated with the reward token ('reward source') or the zero token ('zero source'). Unlike controls, depressed participants failed to show better memory for drawings from the reward source vs the zero source. Consistent with predictions, controls also showed a stronger encoding response to reward tokens vs zero tokens in the right parahippocampus and dopaminergic midbrain, whereas the MDD group showed the opposite pattern-stronger responses to zero vs reward tokens-in these regions. Differential activation of the dopaminergic midbrain by reward vs zero tokens was positively correlated with the reward source memory advantage in controls, but not depressed participants. These data suggest that weaker memory for positive material in depression reflects blunted encoding responses in the dopaminergic midbrain and medial temporal lobes. © The Author (2013). Published by Oxford University Press. For Permissions, please email: journals.permissions@oup.com.

76 FR 62452 - Avon Products, Inc. Including On-Site Leased Workers From Spherion/Source Right, Springdale, OH...

Science.gov (United States)

2011-10-07

.... Including On-Site Leased Workers From Spherion/Source Right, Springdale, OH; Amended Certification Regarding... workers of the subject firm. The company reports that workers leased from Spherion/Source Right were...., including on-site leased workers from Spherion/Source Right, Springdale, Ohio, who became totally or...

Do the enigmatic ``Infrared-Faint Radio Sources'' include pulsars?

Science.gov (United States)

Hobbs, George; Middelberg, Enno; Norris, Ray; Keith, Michael; Mao, Minnie; Champion, David

2009-04-01

The Australia Telescope Large Area Survey (ATLAS) team have surveyed seven square degrees of sky at 1.4GHz. During processing some unexpected infrared-faint radio sources (IFRS sources) were discovered. The nature of these sources is not understood, but it is possible that some of these sources may be pulsars within our own galaxy. We propose to observe the IFRS sources with steep spectral indices using standard search techniques to determine whether or not they are pulsars. A pulsar detection would 1) remove a subset of the IFRS sources from the ATLAS sample so they would not need to be observed with large optical/IR telescopes to find their hosts and 2) be intrinsically interesting as the pulsar would be a millisecond pulsar and/or have an extreme spatial velocity.

Reflection seismic imaging of the upper crystalline crust for characterization of potential repository sites: Fine tuning the seismic source

Energy Technology Data Exchange (ETDEWEB)

Juhlin, C.; Palm, H.; Bergman, B. [Uppsala Univ. (Sweden). Dept. of Earth Sciences

2001-09-01

SKB is currently carrying out studies to determine which seismic techniques, and how, they will be used for investigations prior to and during the building of a high-level nuclear waste repository. Active seismic methods included in these studies are refraction seismics, reflection seismics, and vertical seismic profiling (VSP). The main goal of the active seismic methods is to locate fracture zones in the crystalline bedrock. Plans are to use longer reflection seismic profiles (3.4 km) in the initial stages of the site investigations. The target depth for these seismic profiles is 100-1500 m. Prior to carrying out the seismic surveys over actual candidate waste repository sites it has been necessary to carry out a number of tests to determine the optimum acquisition parameters. This report constitutes a summary of the tests carried out by Uppsala University. In addition, recommended acquisition and processing parameters are presented at the end of the report. A major goal in the testing has been to develop a methodology for acquiring high-resolution reflection seismic data over crystalline rock in as a cost effective manner as possible. Since the seismic source is generally a major cost in any survey, significant attention has been given to reducing the cost of the source. It was agreed upon early in the study that explosives were the best source from a data quality perspective and, therefore, only explosive source methods have been considered in this study. The charge size and shot hole dimension required to image the upper 1-1.5 km of bedrock is dependent upon the conditions at the surface. In this study two types of shot hole drilling methods have been employed depending upon whether the thickness of the loose sediments at the surface is greater or less than 0.5 m. The charge sizes and shot hole dimensions required are: Loose sediment thickness less than 0.5 m: 15 g in 90 cm deep 12 mm wide uncased shot holes. Loose sediment thickness greater than 0.5 m: 75 g

Specific features of diffuse reflection of human face skin for laser and non-laser sources of visible and near-IR light

International Nuclear Information System (INIS)

Dolotov, L E; Sinichkin, Yu P; Tuchin, Valerii V; Al'tshuler, G B; Yaroslavskii, I V

2011-01-01

The specific features of diffuse reflection from different areas of human face skin for laser and non-laser sources of visible and near-IR light have been investigated to localise the closed-eye (eyelid) region. In the visible spectral range the reflection from the eyelid skin surface can be differentiated by measuring the slope of the spectral dependence of the effective optical density of skin in the wavelength range from 650 to 700nm. In the near-IR spectral range the reflectances of the skin surface at certain wavelengths, normalised to the forehead skin reflectance, can be used as a criterion for differentiating the eyelid skin. In this case, a maximum discrimination is obtained when measuring the skin reflectances at laser wavelengths of 1310 and 1470nm, which correspond to the spectral ranges of maximum and minimum water absorption. (optical technologies in biophysics and medicine)

Pseudodynamic Source Characterization for Strike-Slip Faulting Including Stress Heterogeneity and Super-Shear Ruptures

KAUST Repository

Mena, B.

2012-08-08

Reliable ground‐motion prediction for future earthquakes depends on the ability to simulate realistic earthquake source models. Though dynamic rupture calculations have recently become more popular, they are still computationally demanding. An alternative is to invoke the framework of pseudodynamic (PD) source characterizations that use simple relationships between kinematic and dynamic source parameters to build physically self‐consistent kinematic models. Based on the PD approach of Guatteri et al. (2004), we propose new relationships for PD models for moderate‐to‐large strike‐slip earthquakes that include local supershear rupture speed due to stress heterogeneities. We conduct dynamic rupture simulations using stochastic initial stress distributions to generate a suite of source models in the magnitude Mw 6–8. This set of models shows that local supershear rupture speed prevails for all earthquake sizes, and that the local rise‐time distribution is not controlled by the overall fault geometry, but rather by local stress changes on the faults. Based on these findings, we derive a new set of relations for the proposed PD source characterization that accounts for earthquake size, buried and surface ruptures, and includes local rise‐time variations and supershear rupture speed. By applying the proposed PD source characterization to several well‐recorded past earthquakes, we verify that significant improvements in fitting synthetic ground motion to observed ones is achieved when comparing our new approach with the model of Guatteri et al. (2004). The proposed PD methodology can be implemented into ground‐motion simulation tools for more physically reliable prediction of shaking in future earthquakes.

A practical algorithm for distribution state estimation including renewable energy sources

Energy Technology Data Exchange (ETDEWEB)

Niknam, Taher [Electronic and Electrical Department, Shiraz University of Technology, Modares Blvd., P.O. 71555-313, Shiraz (Iran); Firouzi, Bahman Bahmani [Islamic Azad University Marvdasht Branch, Marvdasht (Iran)

2009-11-15

Renewable energy is energy that is in continuous supply over time. These kinds of energy sources are divided into five principal renewable sources of energy: the sun, the wind, flowing water, biomass and heat from within the earth. According to some studies carried out by the research institutes, about 25% of the new generation will be generated by Renewable Energy Sources (RESs) in the near future. Therefore, it is necessary to study the impact of RESs on the power systems, especially on the distribution networks. This paper presents a practical Distribution State Estimation (DSE) including RESs and some practical consideration. The proposed algorithm is based on the combination of Nelder-Mead simplex search and Particle Swarm Optimization (PSO) algorithms, called PSO-NM. The proposed algorithm can estimate load and RES output values by Weighted Least-Square (WLS) approach. Some practical considerations are var compensators, Voltage Regulators (VRs), Under Load Tap Changer (ULTC) transformer modeling, which usually have nonlinear and discrete characteristics, and unbalanced three-phase power flow equations. The comparison results with other evolutionary optimization algorithms such as original PSO, Honey Bee Mating Optimization (HBMO), Neural Networks (NNs), Ant Colony Optimization (ACO), and Genetic Algorithm (GA) for a test system demonstrate that PSO-NM is extremely effective and efficient for the DSE problems. (author)

Reflection and Non-Reflection of Particle Wavepackets

Science.gov (United States)

Cox, Timothy; Lekner, John

2008-01-01

Exact closed-form solutions of the time-dependent Schrodinger equation are obtained, describing the propagation of wavepackets in the neighbourhood of a potential. Examples given include zero reflection, total reflection and partial reflection of the wavepacket, for the sech[superscript 2]x/a, 1/x[superscript 2] and delta(x) potentials,…

THE VARIABLE REFLECTION NEBULA CEPHEUS A EAST

International Nuclear Information System (INIS)

Hodapp, Klaus W.; Bressert, Eli

2009-01-01

We report K'-band imaging observations of the reflection nebula associated with Cepheus A East covering the time interval from 1990 to 2004. Over this time the reflection nebula shows variations of flux distribution, which we interpret as the effect of inhomogeneous and varying extinction in the light path from the illuminating source HW2 to the reflection nebula. The obscuring material is located within typical distances of ∼ 10 AU from the illuminating source.

Reflection-artifact-free photoacoustic imaging using PAFUSion (photoacoustic-guided focused ultrasound)

Science.gov (United States)

Kuniyil Ajith Singh, Mithun; Jaeger, Michael; Frenz, Martin; Steenbergen, Wiendelt

2016-03-01

Reflection artifacts caused by acoustic inhomogeneities are a main challenge to deep-tissue photoacoustic imaging. Photoacoustic transients generated by the skin surface and superficial vasculature will propagate into the tissue and reflect back from echogenic structures to generate reflection artifacts. These artifacts can cause problems in image interpretation and limit imaging depth. In its basic version, PAFUSion mimics the inward travelling wave-field from blood vessel-like PA sources by applying focused ultrasound pulses, and thus provides a way to identify reflection artifacts. In this work, we demonstrate reflection artifact correction in addition to identification, towards obtaining an artifact-free photoacoustic image. In view of clinical applications, we implemented an improved version of PAFUSion in which photoacoustic data is backpropagated to imitate the inward travelling wave-field and thus the reflection artifacts of a more arbitrary distribution of PA sources that also includes the skin melanin layer. The backpropagation is performed in a synthetic way based on the pulse-echo acquisitions after transmission on each single element of the transducer array. We present a phantom experiment and initial in vivo measurements on human volunteers where we demonstrate significant reflection artifact reduction using our technique. The results provide a direct confirmation that reflection artifacts are prominent in clinical epi-photoacoustic imaging, and that PAFUSion can reduce these artifacts significantly to improve the deep-tissue photoacoustic imaging.

Virtual source reflection imaging of the Socorro Magma Body, New Mexico, using a dense seismic array

Science.gov (United States)

Finlay, T. S.; Worthington, L. L.; Schmandt, B.; Hansen, S. M.; Bilek, S. L.; Aster, R. C.; Ranasinghe, N. R.

2017-12-01

The Socorro Magma Body (SMB) is one of the largest known actively inflating continental magmatic intrusions. Previous studies have relied on sparse instrument coverage to determine its spatial extent, depth, and seismic signature, which characterized the body as a thin sill with a surface at 19 km below the Earth's surface. However, over the last two decades, InSAR and magneto-telluric (MT) studies have shed new light on the SMB and invigorated the scientific debate of the spatial distribution and uplift rate of the SMB. We return to seismic imaging of the SMB with the Sevilleta Array, a 12-day deployment of approximately 800 vertical component, 10-Hz geophones north of Socorro, New Mexico above and around the estimated northern half of the SMB. Teleseismic virtual source reflection profiling (TVR) employs the free surface reflection off of a teleseismic P as a virtual source in dense arrays, and has been used successfully to image basin structure and the Moho in multiple tectonic environments. The Sevilleta Array recorded 62 teleseismic events greater than M5. Applying TVR to the data collected by the Sevilleta Array, we present stacks from four events that produced the with high signal-to-noise ratios and simple source-time functions: the February 11, 2015 M6.7 in northern Argentina, the February 19, 2015 M5.4 in Kamchatka, Russia, and the February 21, 2015 M5.1 and February 22, 2015 M5.5 in western Colombia. Preliminary results suggest eastward-dipping reflectors at approximately 5 km depth near the Sierra Ladrones range in the northwestern corner of the array. Further analysis will focus on creating profiles across the area of maximum SMB uplift and constraining basin geometry.

Discharge lamp with reflective jacket

Science.gov (United States)

MacLennan, Donald A.; Turner, Brian P.; Kipling, Kent

2001-01-01

A discharge lamp includes an envelope, a fill which emits light when excited disposed in the envelope, a source of excitation power coupled to the fill to excite the fill and cause the fill to emit light, and a reflector disposed around the envelope and defining an opening, the reflector being configured to reflect some of the light emitted by the fill back into the fill while allowing some light to exit through the opening. The reflector may be made from a material having a similar thermal index of expansion as compared to the envelope and which is closely spaced to the envelope. The envelope material may be quartz and the reflector material may be either silica or alumina. The reflector may be formed as a jacket having a rigid structure which does not adhere to the envelope. The lamp may further include an optical clement spaced from the envelope and configured to reflect an unwanted component of light which exited the envelope back into the envelope through the opening in the reflector. Light which can be beneficially recaptured includes selected wavelength regions, a selected polarization, and selected angular components.

Catheter based mid-infrared reflectance and reflectance generated absorption spectroscopy

Science.gov (United States)

Holman, Hoi-Ying N

2013-10-29

A method of characterizing conditions in a tissue, by (a) providing a catheter that has a light source that emits light in selected wavenumbers within the range of mid-IR spectrum; (b) directing the light from the catheter to an area of tissue at a location inside a blood vessel of a subject; (c) collecting light reflected from the location and generating a reflectance spectra; and (d) comparing the reflectance spectra to a reference spectra of normal tissue, whereby a location having an increased number of absorbance peaks at said selected wavenumbers indicates a tissue inside the blood vessel containing a physiological marker for atherosclerosis.

Controlled Carbon Source Addition to an Alternating Nitrification-Denitrification Wastewater Treatment Process Including Biological P Removal

DEFF Research Database (Denmark)

Isaacs, Steven Howard; Henze, Mogens

1995-01-01

The paper investigates the effect of adding an external carbon source on the rate of denitrification in an alternating activated sludge process including biological P removal. Two carbon sources were examined, acetate and hydrolysate derived from biologically hydrolyzed sludge. Preliminary batch ...

Effect of reflective practice education on self-reflection, insight, and reflective thinking among experienced nurses: a pilot study.

Science.gov (United States)

Asselin, Marilyn E; Fain, James A

2013-01-01

A mixed-method study was conducted to determine whether nurses' participation in a reflective practice continuing education program using a structured reflection model makes a difference in nurses' self-reflection, insight, and reflective thinking about clinical practice situations. Findings suggested that use of structured reflection using question cues, written narratives, and peer-facilitated reflection increased nurses' engagement in self-reflection and enhanced reflective thinking in practice. Including reflective practice education in novice orientation and preceptor training may be beneficial.

Effects of temporal distribution of specular and diffuse reflections on perceived music quality

Science.gov (United States)

Smitthakorn, Pattra

The purpose of this study was to investigate the effects of the temporal distribution of diffuse and specular reflections on the perceived acoustic qualities of music performance. Sets of impulse responses were designed with different temporal distributions of early acoustic energy (specular and diffuse reflections). Then, three types of anechoic sound sources---orchestral music, trumpet, and piano---were convolved with the designed impulse responses. The results from the listening tests revealed that different room environments were needed to acoustically support different source characteristics. The results show the following: (1) specular reflections arriving within 40 msec of the direct sound improved perceived "clarity" and "intimacy"; (2) specular reflections arriving between 40-80 msec after the direct sound improved perceived "clarity" for orchestral music; (3) specular reflections arriving later than 80 msec after the direct sound are not desirable; (4) large numbers of diffuse reflections arriving within 40 and 80 msec of the direct sound improved perceived "intimacy", "texture", and "overall impression" for all sound sources, heightened perceived "clarity" for trumpet and piano, and reduced perceived "glare" for trumpet; and (5) diffuse reflections arriving between 80-160 msec of the direct sound preserved perceived "reverberance" and reduced perceived "echoes" as opposed to specular reflections arriving in the same time period. The results of this study indicate that music performance halls should be designed to include diffuse reflections from surfaces within the 80 msec time period to achieve preferred texture, intimacy, clarity and overall impression and in the 160 msec time period to reduce echoes; specular reflections arriving within the 40 msec time period should be provided to enhance perceived clarity.

Seismic reflection imaging, accounting for primary and multiple reflections

Science.gov (United States)

Wapenaar, Kees; van der Neut, Joost; Thorbecke, Jan; Broggini, Filippo; Slob, Evert; Snieder, Roel

2015-04-01

Imaging of seismic reflection data is usually based on the assumption that the seismic response consists of primary reflections only. Multiple reflections, i.e. waves that have reflected more than once, are treated as primaries and are imaged at wrong positions. There are two classes of multiple reflections, which we will call surface-related multiples and internal multiples. Surface-related multiples are those multiples that contain at least one reflection at the earth's surface, whereas internal multiples consist of waves that have reflected only at subsurface interfaces. Surface-related multiples are the strongest, but also relatively easy to deal with because the reflecting boundary (the earth's surface) is known. Internal multiples constitute a much more difficult problem for seismic imaging, because the positions and properties of the reflecting interfaces are not known. We are developing reflection imaging methodology which deals with internal multiples. Starting with the Marchenko equation for 1D inverse scattering problems, we derived 3D Marchenko-type equations, which relate reflection data at the surface to Green's functions between virtual sources anywhere in the subsurface and receivers at the surface. Based on these equations, we derived an iterative scheme by which these Green's functions can be retrieved from the reflection data at the surface. This iterative scheme requires an estimate of the direct wave of the Green's functions in a background medium. Note that this is precisely the same information that is also required by standard reflection imaging schemes. However, unlike in standard imaging, our iterative Marchenko scheme retrieves the multiple reflections of the Green's functions from the reflection data at the surface. For this, no knowledge of the positions and properties of the reflecting interfaces is required. Once the full Green's functions are retrieved, reflection imaging can be carried out by which the primaries and multiples are

Using the combination refraction-reflection solid to design omni-directional light source used in underwater wireless optical communication

Science.gov (United States)

Rao, Jionghui; Yao, Wenming; Wen, Linqiang

2015-10-01

Underwater wireless optical communication is a communication technology which uses laser as an information carrier and transmits data through water. Underwater wireless optical communication has some good features such as broader bandwidth, high transmission rate, better security, anti—interference performance. Therefore, it is promising to be widely used in the civil and military communication domains. It is also suitable for high-speed, short-range communication between underwater mobile vehicles. This paper presents a design approach of omni-directional light source used in underwater wireless optical communication, using TRACEPRO simulation tool to help design a combination solid composed of the lens, conical reflector and parabolic reflector, and using the modulated DPSS green laser in the transmitter module to output the laser beam in small divergence angles, after expanded by the combination refraction-reflection solid, the angle turns into a space divergence angle of 2π, achieving the omni-directional light source of hemisphere space, and test in the air and underwater, the result shows that the effect is fine. This paper analyzes the experimental test in the air and water, in order to make further improvement of the uniformity of light distribution, we optimize the reflector surface parameters of combination refraction-reflection solid and test in the air and water. The result shows that omni-directional light source used in underwater wireless optical communication optimized could achieve the uniformity of light distribution of underwater space divergence angle of 2π. Omni-directional light source used in underwater wireless optical communication designed in this paper has the characteristics of small size and uniformity of light distribution, it is suitable for application between UUVs, AUVs, Swimmer Delivery Vehicles (SDVs) and other underwater vehicle fleet, it realizes point-to-multipoint communications.

Development of paints with infrared radiation reflective properties

Directory of Open Access Journals (Sweden)

Eliane Coser

2015-06-01

Full Text Available AbstractLarge buildings situated in hot regions of the Globe need to be agreeable to their residents. Air conditioning is extensively used to make these buildings comfortable, with consequent energy consumption. Absorption of solar visible and infrared radiations are responsible for heating objects on the surface of the Earth, including houses and buildings. To avoid excessive energy consumption, it is possible to use coatings formulated with special pigments that are able to reflect the radiation in the near- infrared, NIR, spectrum. To evaluate this phenomenon an experimental study about the reflectivity of paints containing infrared-reflective pigments has been made. By irradiating with an IR source and by measuring the surface temperatures of the samples we evaluated: color according to ASTM D 2244-14, UV/VIS/NIR reflectance according to ASTM E 903-12 and thermal performance. Additionally, the spectral reflectance and the IR emittance were measured and the solar reflectance of the samples were calculated. The results showed that plates coated with paints containing IR-reflecting pigments displayed lower air temperature on the opposite side as compared to conventional coatings, indicating that they can be effective to reflect NIR and decrease the temperature of buildings when used in roofs and walls.

Reflecting on reflection in interprofessional education: implications for theory and practice.

Science.gov (United States)

Clark, Phillip G

2009-05-01

Interprofessional education (IPE) involves learning, and learning requires reflection. Educators need to "reflect more on reflection" if they are to be effective teachers in ensuring the learning outcomes essential for teamwork and interprofessional practice (IPP), including incorporating both theory and practice into the development of educational interventions. First, this discussion surveys the IPE-relevant literature on reflection, and then defines and refines the multidimensional concept of reflection as it relates to IPE in developing and implementing teamwork learning programs and experiences. Second, specific methods to promote reflection are presented and explored, including self-assessments, journaling, and written papers. Actual samples from student journals and assignments provide examples of the impacts of using these methods on participant reflection and learning. Finally, implications for an expanded understanding and application of reflection for IPE will be discussed, and recommendations made for educational practice and research in this area.

Apparatus including concave reflectors and a line of optical fibers

International Nuclear Information System (INIS)

Dolan, J.T.

1992-01-01

This patent describes an apparatus including a radiation source which emits in a multiplicity of directions for focusing radiation on an object which may receive radiation within a certain solid angle. It comprises a first reflector and a second reflector, the first reflector being elliptical in cross section and having a first focus and a second focus, the second reflector being circular in cross section and having a center, and a radius equal to the distance between the second reflector and the first focus, the first reflector and the second reflector being arranged so that a concave reflecting surface of the first reflector faces a concave reflecting surface of the second reflector, and so arranged that the first focus of the first reflector corresponds to the center of the second reflector, the radiation source being an elongated discharge bulb, the object being a group of two or more optical fibers defining at least one line of optical fibers which are located at the second focus of the first reflector

Sources of institutional pressure: reflections on legitimacy in the Brazilian hotel industry

Directory of Open Access Journals (Sweden)

Erick Pusch Wilke

2013-08-01

Full Text Available The rules and regulations created and consolidated in society make up a set of institutional forces that press organizations seek legitimacy in their industry (Oliver, 1988; Deephouse, 1996. Although the literature has dismissed efforts to identify the forces that contribute to the isomorphism of the organizations belonging to the service sector, such as hospitals and social services, there are still gaps to be filled specifically as it relates to the hospitality industry. In this sense, the aim of this study has centered on establishing reflections on the legitimacy in the hotel industry and the factors that determine its occurrence. Methodologically, we raise the seminal studies and recent contributions on institutional theory and strategy in hospitality. Conclusively, our premises that the main sources of institutional legitimacy of hospitality organizations, the use of managerial and technical expertise, the abide by legal requisites – imperative and optional – and the imitation organizational success, in fact originate, circumstantially, from one or from the combination of the above mentioned forces.

Retrieval of reflections from ambient noise using illumination diagnosis

Science.gov (United States)

Vidal, C. Almagro; Draganov, D.; van der Neut, J.; Drijkoningen, G.; Wapenaar, K.

2014-09-01

Seismic interferometry (SI) enables the retrieval of virtual sources at the location of receivers. In the case of passive SI, no active sources are used for the retrieval of the reflection response of the subsurface, but ambient-noise recordings only. The resulting retrieved response is determined by the illumination characteristics of the recorded ambient noise. Characteristics like geometrical distribution and signature of the noise sources, together with the complexity of the medium and the length of the noise records, determine the quality of the retrieved virtual-shot events. To retrieve body wave reflections, one needs to correlate body-wave noise. A source of such noise might be regional seismicity. In regions with notable human presence, the dominant noise sources are generally located at or close to the surface. In the latter case, the noise will be dominated by surface waves and consequently also the retrieved virtual common-source panels will contain dominant retrieved surface waves, drowning out possible retrieved reflections. In order to retrieve reflection events, suppression of the surface waves becomes the most important pre-processing goal. Because of the reasons mentioned above, we propose a fast method to evaluate the illumination characteristics of ambient noise using the correlation results from ambient-noise records. The method is based on the analysis of the so-called source function of the retrieved virtual-shot panel, and evaluates the apparent slowness of arrivals in the correlation results that pass through the position of the virtual source and at zero time. The results of the diagnosis are used to suppress the retrieval of surface waves and therefore to improve the quality of the retrieved reflection response. We explain the approach using modelled data from transient and continuous noise sources and an example from a passive field data set recorded at Annerveen, Northern Netherlands.

The reflection component in NS LMXBs

Directory of Open Access Journals (Sweden)

D’Aí A.

2014-01-01

Full Text Available Thanks to the good spectral resolution and large effective area of the EPIC/PN instrument on board of XMM-Newton, we have at hand a large number of observations of accreting low-mass X-ray binaries, that allow for the fist time a comprehensive view on the characteristics of the reflection component at different accretion regimes and to probe the effects of a magnetosphere on its formation. We focus here on a comparative analysis of the reflection component from a series of spectroscopic studies on selected sources: 4U 1705-44, observed both in the soft and hard state, the pulsating ms pulsars SAX J1808.4-3658 and IGR J17511-3057, and the intermittent pulsar HETE J1900-2455. Although the sources can present very similar accretion rates and continuum shapes, the reflection parameters do not generally result the same, moreover the effect of a magnetosphere on the formation of the reflection component appears elusive.

More than reflections: Empathy in motivational interviewing includes language style synchrony between therapist and client

Science.gov (United States)

Lord, Sarah Peregrine; Sheng, Elisa; Imel, Zac E.; Baer, John; Atkins, David C.

2016-01-01

Empathy is a basic psychological process that involves the development of synchrony in dyads. It is also a foundational ingredient in specific, evidence-based behavioral treatments like motivational interviewing (MI). Ratings of therapist empathy typically rely on a gestalt, “felt sense” of therapist understanding and the presence of specific verbal behaviors like reflective listening. These ratings do not provide a direct test of psychological processes like behavioral synchrony that are theorized to be an important component of empathy in psychotherapy. To explore a new objective indicator of empathy, we hypothesized that synchrony in language style (i.e., matching how statements are phrased) between client and therapists would predict gestalt ratings of empathy over and above the contribution of reflections. We analyzed 122 MI transcripts with high and low empathy ratings based on the Motivational Interviewing Treatment Integrity (MITI) global rating scale. Linguistic inquiry and word count was used to estimate language style synchrony (LSS) of adjacent client and therapist talk turns. High empathy sessions showed greater LSS across 11 language style categories compared to low empathy sessions (p empathy vs. low empathy sessions (d = 0.62). Regression analyses showed that LSS was predictive of empathy ratings over and above reflection counts; a 1 SD increase in LSS is associated with 2.4 times increase in the odds of a high empathy rating, controlling for therapist reflections (odds ratio = 2.4, 95% CI: 1.36, 4.24, p empathy ratings are related to synchrony in language style, over and above synchrony of content as measured by therapist reflections. Novel indicators of therapist empathy may have implications for the study of MI process as well as the training of therapists. PMID:25892166

Reflective photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Lentine, Anthony L.; Nielson, Gregory N.; Cruz-Campa, Jose Luis; Okandan, Murat; Goeke, Ronald S.

2018-03-06

A photovoltaic module includes colorized reflective photovoltaic cells that act as pixels. The colorized reflective photovoltaic cells are arranged so that reflections from the photovoltaic cells or pixels visually combine into an image on the photovoltaic module. The colorized photovoltaic cell or pixel is composed of a set of 100 to 256 base color sub-pixel reflective segments or sub-pixels. The color of each pixel is determined by the combination of base color sub-pixels forming the pixel. As a result, each pixel can have a wide variety of colors using a set of base colors, which are created, from sub-pixel reflective segments having standard film thicknesses.

Low levels of persistent organic pollutants (POPs) in New Zealand eels reflect isolation from atmospheric sources

International Nuclear Information System (INIS)

Holmqvist, Niklas; Stenroth, Patrik; Berglund, Olof; Nystroem, Per; Olsson, Karin; Jellyman, Don; McIntosh, Angus R.; Larsson, Per

2006-01-01

Polychlorinated biphenyls (PCBs) and organic pesticides (i.e., DDTs) were measured in long finned eels (Anguilla dieffenbachii) in 17 streams on the west coast of South Island, New Zealand. Very low levels of PCBs and low levels of ppDDE were found. The concentrations of PCBs and ppDDE were not correlated within sites indicating that different processes determined the levels of the two pollutants in New Zealand eels. The PCBs probably originate from atmospheric transport, ppDDE levels are determined by land use and are higher in agriculture areas. The low contamination level of these aquatic systems seems to be a function of a low input from both long and short-range transport as well as few local point sources. No correlation could be found between lipid content and persistent organic pollutants (POPs) concentration (as shown in previous studies) in the eels which could be explained by low and irregular intake of the pollutants. - Low levels of PCBs found in New Zealand eels reflect isolation from atmospheric sources while DDTs levels are determined by land use

On the reflection point where light reflects to a known destination on quadratic surfaces.

Science.gov (United States)

Gonçalves, Nuno

2010-01-15

We address the problem of determining the reflection point on a specular surface where a light ray that travels from a source to a target is reflected. The specular surfaces considered are those expressed by a quadratic equation. So far, there is no closed form explicit equation for the general solution of this determination of the reflection point, and the usual approach is to use the Snell law or the Fermat principle whose equations are derived in multidimensional nonlinear minimizations. We prove in this Letter that one can impose a set of three restrictions to the reflection point that can impose a set of three restrictions that culminates in a very elegant formalism of searching the reflection point in a unidimensional curve in space. This curve is the intersection of two quadratic equations. Some applications of this framework are also discussed.

The Play Curricular Activity Reflection Discussion Model for Game-Based Learning

Science.gov (United States)

Foster, Aroutis; Shah, Mamta

2015-01-01

This article elucidates the process of game-based learning in classrooms through the use of the Play Curricular activity Reflection Discussion (PCaRD) model. A mixed-methods study was conducted at a high school to implement three games with the PCaRD model in a year-long elective course. Data sources included interviews and observations for…

Spectral implementation of full waveform inversion based on reflections

KAUST Repository

Wu, Zedong; Alkhalifah, Tariq Ali

2014-01-01

Using the reflection imaging process as a source to model reflections for full waveform inversion (FWI), referred to as reflection FWI (RFWI), allows us to update the background component of the model, and avoid using the relatively costly migration

Description and validation of a combination of acoustical radiosity and the image source method

DEFF Research Database (Denmark)

Marbjerg, Gerd Høy; Jeong, Cheol-Ho; Brunskog, Jonas

2014-01-01

A model that combines image source modelling and acoustical radiosity with complex boundary con- ditions, thus including phase shifts on reflection, has been developed. The model is denoted Phased Acoustical Radiosity and Image Source Model (PARISM). It has been developed in order to be able...... to model both specular and diffuse reflections with complex-valued acoustical descriptions of the surfaces. This paper mainly describes the combination of the two models and the implementation of the angle dependent surface descriptions both in the image source model and in acoustical radiosity...

Influence of ionization on reflection of solitary waves in a magnetized plasma

International Nuclear Information System (INIS)

Jyoti,; Malik, Hitendra K.; Kumar, Ravinder; Dahiya, Raj P.

2013-01-01

The reflection of nonlinear solitary waves is studied in a nonuniform, magnetized plasma diffusing from an ionization source along the magnetic field lines. Contribution of the ionization term is included in the continuity equation. The behavior of solitary waves is governed by modified form of Korteweg–de Vries equation (called mKdV equation). In order to investigate the reflection of solitary waves, the mKdV equations for the right and left going waves are derived, and solved by finding new transformations coupled at the point of reflection, for obtaining the expression of reflection coefficient. Contrary to the case of usual inhomogeneous plasma, the present analysis shows that a combination of usual sech 2 structure and tanh structure (called the tail of soliton) arises due to the influence of ionization term. Interestingly, this tailing structure disappears after the reflection of the soliton and hence, the soliton is downshifted prominently

Increasing the brightness of light sources

Energy Technology Data Exchange (ETDEWEB)

Fu, Ling

2006-11-16

In this work the principle of light recycling is applied to artificial light sources in order to achieve brightness enhancement. Firstly, the feasibilities of increasing the brightness of light sources via light recycling are examined theoretically, based on the fundamental laws of thermodynamics including Kirchhoff's law on radiation, Planck's law, Lambert-Beer's law, the etendue conservation and the brightness theorem. From an experimental viewpoint, the radiation properties of three different kinds of light sources including short-arc lamps, incandescent lamps and LEDs characterized by their light-generating mechanisms are investigated. These three types of sources are used in light recycling experiments, for the purpose of 1. validating the intrinsic light recycling effect in light sources, e. g. the intrinsic light recycling effect in incandescent lamps stemming from the coiled filament structure. 2. acquiring the required parameters for establishing physical models, e.g. the emissivity/absorptivity of the short-arc lamps, the intrinsic reflectivity and the external quantum efficiency of LEDs. 3. laying the foundations for designing optics aimed at brightness enhancement according to the characteristics of the sources and applications. Based on the fundamental laws and experiments, two physical models for simulating the radiance distribution of light sources are established, one for thermal filament lamps, the other for luminescent sources, LEDs. As validation of the theoretical and experimental investigation of the light recycling effect, an optical device, the Carambola, is designed for achieving deterministic and multiple light recycling. The Carambola has the function of a concentrator. In order to achieve the maximum possible brightness enhancement with the Carambola, several combinations of sources and Carambolas are modelled in ray-tracing simulations. Sources with different light-emitting mechanisms and different radiation properties

Site Characterization of the Source Physics Experiment Phase II Location Using Seismic Reflection Data

Science.gov (United States)

Sexton, E. A.; Snelson, C. M.; Chipman, V.; Emer, D. F.; White, R. L.; Emmitt, R.; Wright, A. A.; Drellack, S.; Huckins-Gang, H.; Mercadante, J.; Floyd, M.; McGowin, C.; Cothrun, C.; Bonal, N.

2013-12-01

An objective of the Source Physics Experiment (SPE) is to identify low-yield nuclear explosions from a regional distance. Low-yield nuclear explosions can often be difficult to discriminate among the clutter of natural and man-made explosive events (e.g., earthquakes and mine blasts). The SPE is broken into three phases. Phase I has provided the first of the physics-based data to test the empirical models that have been used to discriminate nuclear events. The Phase I series of tests were placed within a highly fractured granite body. The evolution of the project has led to development of Phase II, to be placed within the opposite end member of geology, an alluvium environment, thereby increasing the database of waveforms to build upon in the discrimination models. Both the granite and alluvium sites have hosted nearby nuclear tests, which provide comparisons for the chemical test data. Phase III of the SPE is yet to be determined. For Phase II of the experiment, characterization of the location is required to develop the geologic/geophysical models for the execution of the experiment. Criteria for the location are alluvium thickness of approximately 170 m and a water table below 170 m; minimal fracturing would be ideal. A P-wave mini-vibroseis survey was conducted at a potential site in alluvium to map out the subsurface geology. The seismic reflection profile consisted of 168 geophone stations, spaced 5 m apart. The mini-vibe was a 7,000-lb peak-force source, starting 57.5 m off the north end of the profile and ending 57.5 m past the southern-most geophone. The length of the profile was 835 m. The source points were placed every 5 m, equally spaced between geophones to reduce clipping. The vibroseis sweep was from 20 Hz down to 180 Hz over 8 seconds, and four sweeps were stacked at each shot location. The shot gathers show high signal-to-noise ratios with clear first arrivals across the entire spread and the suggestion of some shallow reflectors. The data were

Tunable All Reflective Spatial Heterodyne Spectroscopy, A Technique For High Resolving Power Observation OI Defused Emission Line Sources

Science.gov (United States)

Hosseini, Seyedeh Sona

The solar system presents a challenge to spectroscopic observers, because it is an astrophysically low energy environment populated with often angularly extended targets (e.g, interplanetary medium, comets, planetary upper atmospheres, and planet and satellite near space environments). Spectroscopy is a proven tool for determining compositional and other properties of remote objects. Narrow band imaging and low resolving spectroscopic measurements provide information about composition, photochemical evolution, energy distribution and density. The extension to high resolving power provides further access to temperature, velocity, isotopic ratios, separation of blended sources, and opacity effects. The drawback of high-resolution spectroscopy comes from the instrumental limitations of lower throughput, the necessity of small entrance apertures, sensitivity, field of view, and large physical instrumental size. These limitations quickly become definitive for faint and/or extended targets and for spacecraft encounters. An emerging technique with promise for the study of faint, extended sources at high resolving power is the all-reflective form of the Spatial Heterodyne Spectrometer (SHS). SHS instruments are compact and naturally possess both high etendue and high resolving power. To achieve similar spectral grasp, grating spectrometers require big telescopes. SHS is a common-path beam Fourier transform interferometer that produces Fizeau fringe pattern for all other wavelengths except the tuned wavelength. Compared to similar Fourier transform Spectrometers (FTS), SHS has considerably relaxed optical tolerances that make it easier to use in the visible and UV spectral ranges. The large etendue of SHS instruments makes them ideal for observations of extended, low surface brightness, isolated emission line sources, while their intrinsically high spectral resolution enables the study of the dynamical and spectral characteristics described above. SHS also combines very

Detection limit calculations for different total reflection techniques

International Nuclear Information System (INIS)

Sanchez, H.J.

2000-01-01

In this work, theoretical calculations of detection limits for different total-reflection techniques are presented.. Calculations include grazing incidence (TXRF) and gracing exit (GEXRF) conditions. These calculations are compared with detection limits obtained for conventional x-ray fluorescence (XRF). In order to compute detection limits the Shiraiwa and Fujino's model to calculate x-ray fluorescence intensities was used. This model made certain assumptions and approximations to achieve the calculations, specially in the case of the geometrical conditions of the sample, and the incident and takeoff beams. Nevertheless the calculated data of detection limits for conventional XRF and total-reflection XRF show a good agreement with previous results. The model proposed here allows to analyze the different sources of background and the influence of the excitation geometry, which contribute to the understanding of the physical processes involved in the XRF analysis by total reflection. Finally, a comparison between detection limits in total-reflection analysis at grazing incidence and at grazing exit is carried out. Here a good agreement with the theoretical predictions of the reversibility principle is found, showing that detection limits are similar for both techniques. (author)

Mid infrared upconversion spectroscopy using diffuse reflectance

DEFF Research Database (Denmark)

Sanders, Nicolai Højer; Kehlet, Louis M.; Dam, Jeppe Seidelin

2014-01-01

specifically that upconversion methods can be deployed using a diffuse reflectance setup where the test sample is irradiated by a thermal light source, i.e. a globar. The diffuse reflectance geometry is particularly well suited when a transmission setup cannot be used. This situation may happen for highly...

Subjective Response to Foot-Fall Noise, Including Localization of the Source Position

DEFF Research Database (Denmark)

Brunskog, Jonas; Hwang, Ha Dong; Jeong, Cheol-Ho

2011-01-01

annoyance, using simulated binaural room impulse responses, with sources being a moving point source or a nonmoving surface source, and rooms being a room with a reverberation time of 0.5 s or an anechoic room. The paper concludes that no strong effect of the source localization on the annoyance can...

Fostering Critical Reflection: Moving From a Service to a Social Justice Paradigm.

Science.gov (United States)

Owen, Julie E

2016-06-01

This chapter explores how community engagement creates opportunities to facilitate meaningful discussions about issues including: the nature and sources of power; who benefits and who is silenced by service and leadership efforts; which community actions result in change rather than charity; and how to developmentally sequence reflective practice. © 2016 Wiley Periodicals, Inc., A Wiley Company.

Novel Method To Identify Source-Associated Phylogenetic Clustering Shows that Listeria monocytogenes Includes Niche-Adapted Clonal Groups with Distinct Ecological Preferences

DEFF Research Database (Denmark)

Nightingale, K. K.; Lyles, K.; Ayodele, M.

2006-01-01

population are identified (TreeStats test). Analysis of sequence data for 120 L. monocytogenes isolates revealed evidence of clustering between isolates from the same source, based on the phylogenies inferred from actA and inlA (P = 0.02 and P = 0.07, respectively; SourceCluster test). Overall, the Tree...... are biologically valid. Overall, our data show that (i) the SourceCluster and TreeStats tests can identify biologically meaningful source-associated phylogenetic clusters and (ii) L. monocytogenes includes clonal groups that have adapted to infect specific host species or colonize nonhost environments......., including humans, animals, and food. If the null hypothesis that the genetic distances for isolates within and between source populations are identical can be rejected (SourceCluster test), then particular clades in the phylogenetic tree with significant overrepresentation of sequences from a given source...

Supporting Teacher Reflection through Online Discussion

Directory of Open Access Journals (Sweden)

Jiening Ruan

2011-12-01

Full Text Available The purpose of this case study was to investigate online discussion as a means to promote critical reflection. The study was conducted during a semester-long graduate course on issues related to literacy instructional strategies. The participants in the study were four reading education candidates. During the semester they participated in online discussion about course readings and reflected on their own teaching experiences. The data sources were the online discussion postings, responses to questionnaires, and interviews. The results suggest that technology-mediated discussion strengthens the learning community, facilitates sharing of professional experience among participants, and enhances teacher reflection. The results also point to the multi-faceted nature of teacher reflection.

Hemispherical reflectance model for passive images in an outdoor environment.

Science.gov (United States)

Kim, Charles C; Thai, Bea; Yamaoka, Neil; Aboutalib, Omar

2015-05-01

We present a hemispherical reflectance model for simulating passive images in an outdoor environment where illumination is provided by natural sources such as the sun and the clouds. While the bidirectional reflectance distribution function (BRDF) accurately produces radiance from any objects after the illumination, using the BRDF in calculating radiance requires double integration. Replacing the BRDF by hemispherical reflectance under the natural sources transforms the double integration into a multiplication. This reduces both storage space and computation time. We present the formalism for the radiance of the scene using hemispherical reflectance instead of BRDF. This enables us to generate passive images in an outdoor environment taking advantage of the computational and storage efficiencies. We show some examples for illustration.

Infrared reflection properties and modelling of in situ reflection measurements on plasma-facing materials in Tore Supra

International Nuclear Information System (INIS)

Reichle, R; Desgranges, C; Faisse, F; Pocheau, C; Lasserre, J-P; Oelhoffen, F; Eupherte, L; Todeschini, M

2009-01-01

Tore Supra has-like ITER-reflecting internal surfaces, which can perturb the machine protection systems based on infrared (IR) thermography. To ameliorate this situation, we have measured and modelled in the 3-5 μm wavelength range the bi-directional reflection distribution function (BRDF) of wall material samples from Tore Supra and conducted in situ reflection measurements and simulated them with the CEA COSMOS code. BRDF results are presented for B 4 C and carbon fibre composite (CFC) tiles. The hemispherical integrated reflection ranges from 0.12 for the B 4 C sample to 0.39 for a CFC tile from the limiter erosion zone. In situ measurements of the IR reflection of a blackbody source off an ICRH and an LHCD antenna of Tore Supra are well reproduced by the simulation.

Infrared reflection properties and modelling of in situ reflection measurements on plasma-facing materials in Tore Supra

Energy Technology Data Exchange (ETDEWEB)

Reichle, R; Desgranges, C; Faisse, F; Pocheau, C [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Lasserre, J-P; Oelhoffen, F; Eupherte, L; Todeschini, M [CEA, DAM, CESTA, F-33114 Le Barp (France)

2009-12-15

Tore Supra has-like ITER-reflecting internal surfaces, which can perturb the machine protection systems based on infrared (IR) thermography. To ameliorate this situation, we have measured and modelled in the 3-5 {mu}m wavelength range the bi-directional reflection distribution function (BRDF) of wall material samples from Tore Supra and conducted in situ reflection measurements and simulated them with the CEA COSMOS code. BRDF results are presented for B{sub 4}C and carbon fibre composite (CFC) tiles. The hemispherical integrated reflection ranges from 0.12 for the B{sub 4}C sample to 0.39 for a CFC tile from the limiter erosion zone. In situ measurements of the IR reflection of a blackbody source off an ICRH and an LHCD antenna of Tore Supra are well reproduced by the simulation.

Hybrid Design of Electric Power Generation Systems Including Renewable Sources of Energy

Science.gov (United States)

Wang, Lingfeng; Singh, Chanan

2008-01-01

With the stricter environmental regulations and diminishing fossil-fuel reserves, there is now higher emphasis on exploiting various renewable sources of energy. These alternative sources of energy are usually environmentally friendly and emit no pollutants. However, the capital investments for those renewable sources of energy are normally high,…

Effect of reflecting modes on combined heat transfer within an anisotropic scattering slab

International Nuclear Information System (INIS)

Yi Hongliang; Tan Heping; Lu Yiping

2005-01-01

Under various interface reflecting modes, different transient thermal responses will occur in the media. Combined radiative-conductive heat transfer is investigated within a participating, anisotropic scattering gray planar slab. The two interfaces of the slab are considered to be diffuse and semitransparent. Using the ray tracing method, an anisotropic scattering radiative transfer model for diffuse reflection at boundaries is set up, and with the help of direct radiative transfer coefficients, corresponding radiative transfer coefficients (RTCs) are deduced. RTCs are used to calculate the radiative source term in energy equation. Transient energy equation is solved by the full implicit control-volume method under the external radiative-convective boundary conditions. The influences of two reflecting modes including both specular reflection and diffuse reflection on transient temperature fields and steady heat flux are examined. According to numerical results obtained in this paper, it is found that there exits great difference in thermal behavior between slabs with diffuse interfaces and that with specular interfaces for slabs with big refractive index

State-dependent cellular activity patterns of the cat paraventricular hypothalamus measured by reflectance imaging

DEFF Research Database (Denmark)

Kristensen, Morten Pilgaard; Rector, D M; Poe, G R

1996-01-01

Activity within the cat paraventricular hypothalamus (PVH) during sleep and waking states was measured by quantifying intrinsic tissue reflectivity. A fiber optic probe consisting of a 1.0 mm coherent image conduit, surrounded by plastic fibers which conducted 660 nm source light, was attached...... to a charge-coupled device camera, and positioned over the PVH in five cats. Electrodes for assessing state variables, including electroencephalographic activity, eye movement, and somatic muscle tone were also placed. After surgical recovery, reflected light intensity was measured continuously at 2.5 Hz...

Tunable Reflective Spatial Heterodyne Spectrometer: A Technique for High Resolving Power, Wide Field Of View Observation Of Diffuse Emission Line Sources

Science.gov (United States)

Hosseini, Seyedeh Sona

The purpose of this dissertation is to discuss the need for new technology in broadband high-resolution spectroscopy based on the emerging technique of Spatial Heterodyne Spectroscopy (SHS) and to propose new solutions that should enhance and generalize this technology to other fields. Spectroscopy is a proven tool for determining compositional and other properties of remote objects. Narrow band imaging and low resolving spectroscopic measurements provide information about composition, photochemical evolution, energy distribution and density. The extension to high resolving power provides further access to temperature, velocity, isotopic ratios, separation of blended sources, and opacity effects. In current high resolving power devices, the drawback of high-resolution spectroscopy is bound to the instrumental limitations of lower throughput, the necessity of small entrance apertures, sensitivity, field of view, and large physical instrumental size. These limitations quickly become handicapping for observation of faint and/or extended targets and for spacecraft encounters. A technique with promise for the study of faint and extended sources at high resolving power is the reflective format of the Spatial Heterodyne Spectrometer (SHS). SHS instruments are compact and naturally tailored for both high etendue (defined in section 2.2.5) and high resolving power. In contrast, to achieve similar spectral grasp, grating spectrometers require large telescopes. For reference, SHS is a cyclical interferometer that produces Fizeau fringe pattern for all other wavelengths except the tuned wavelength. The large etendue obtained by SHS instruments makes them ideal for observations of extended, low surface brightness, isolated emission line sources, while their intrinsically high spectral resolution enables one to study the dynamical and physical properties described above. This document contains four chapters. Chapter 1, introduces a class of scientific targets that formerly have

Light reflection from a rough liquid surface including wind-wave effects in a scattering atmosphere

International Nuclear Information System (INIS)

Salinas, Santo V.; Liew, S.C.

2007-01-01

Visible and near-IR images of the ocean surface, taken from remote satellites, often contain important information of near-surface or sub-surface processes, which occur on, or over the ocean. Remote measurements of near surface winds, sea surface temperature and salinity, ocean color and underwater bathymetry, all, one way or another, depend on how well we understand sea surface roughness. However, in order to extract useful information from our remote measurements, we need to construct accurate models of the transfer of solar radiation inside the atmosphere as well as, its reflection from the sea surface. To approach this problem, we numerically solve the radiative transfer equation (RTE) by implementing a model for the atmosphere-ocean system. A one-dimensional atmospheric radiation model is solved via the widely known doubling and adding method and the ocean body is treated as a boundary condition to the problem. The ocean surface is modeled as a rough liquid surface which includes wind interaction and wave states, such as wave age. The model can have possible applications to the retrieval of wind and wave states, such as wave age, near a Sun glint region

Analytic Reflected Lightcurves for Exoplanets

Science.gov (United States)

Haggard, Hal M.; Cowan, Nicolas B.

2018-04-01

The disk-integrated reflected brightness of an exoplanet changes as a function of time due to orbital and rotational motion coupled with an inhomogeneous albedo map. We have previously derived analytic reflected lightcurves for spherical harmonic albedo maps in the special case of a synchronously-rotating planet on an edge-on orbit (Cowan, Fuentes & Haggard 2013). In this letter, we present analytic reflected lightcurves for the general case of a planet on an inclined orbit, with arbitrary spin period and non-zero obliquity. We do so for two different albedo basis maps: bright points (δ-maps), and spherical harmonics (Y_l^m-maps). In particular, we use Wigner D-matrices to express an harmonic lightcurve for an arbitrary viewing geometry as a non-linear combination of harmonic lightcurves for the simpler edge-on, synchronously rotating geometry. These solutions will enable future exploration of the degeneracies and information content of reflected lightcurves, as well as fast calculation of lightcurves for mapping exoplanets based on time-resolved photometry. To these ends we make available Exoplanet Analytic Reflected Lightcurves (EARL), a simple open-source code that allows rapid computation of reflected lightcurves.

The European source-term evaluation code ASTEC: status and applications, including CANDU plant applications

International Nuclear Information System (INIS)

Van Dorsselaere, J.P.; Giordano, P.; Kissane, M.P.; Montanelli, T.; Schwinges, B.; Ganju, S.; Dickson, L.

2004-01-01

Research on light-water reactor severe accidents (SA) is still required in a limited number of areas in order to confirm accident-management plans. Thus, 49 European organizations have linked their SA research in a durable way through SARNET (Severe Accident Research and management NETwork), part of the European 6th Framework Programme. One goal of SARNET is to consolidate the integral code ASTEC (Accident Source Term Evaluation Code, developed by IRSN and GRS) as the European reference tool for safety studies; SARNET efforts include extending the application scope to reactor types other than PWR (including VVER) such as BWR and CANDU. ASTEC is used in IRSN's Probabilistic Safety Analysis level 2 of 900 MWe French PWRs. An earlier version of ASTEC's SOPHAEROS module, including improvements by AECL, is being validated as the Canadian Industry Standard Toolset code for FP-transport analysis in the CANDU Heat Transport System. Work with ASTEC has also been performed by Bhabha Atomic Research Centre, Mumbai, on IPHWR containment thermal hydraulics. (author)

The Beauty of Teachers' Work in Reflections of Ukrainian and Polish Teachers

Science.gov (United States)

Semenog, Olena

2014-01-01

The values of human labor and teacher's work have been reflected on the basis of lexicographical sources and research reflections of famous Ukrainian and Polish pedagogues, such as T. Novatskiy, N. Nychkalo, Pope Paul II, G. Skovoroda, Z. Vyatrovskiy, I. Zyazyun. Among the existing values presented in lexicographical sources the following…

Production sources and management of tritium generated by nuclear facilities. Works reporting from the reflection group 'tritium defense-in-depth'

International Nuclear Information System (INIS)

2001-01-01

This report synthesizes current knowledge of tritium, its sources of tritium and its behavior in reactors and nuclear facilities. In addition, liquid and gaseous tritiated releases and the processes of separation and possible trapping of this radionuclide are displayed. This report also provides elements of reflection on the management of tritium produced today by these facilities, both in France and abroad. It presents insights on the relevance of current management modes of tritiated liquid and solid waste and also on the associated measures to reduce releases of tritium into the environment. (author)

Manipulating acoustic wave reflection by a nonlinear elastic metasurface

Science.gov (United States)

Guo, Xinxin; Gusev, Vitalyi E.; Bertoldi, Katia; Tournat, Vincent

2018-03-01

The acoustic wave reflection properties of a nonlinear elastic metasurface, derived from resonant nonlinear elastic elements, are theoretically and numerically studied. The metasurface is composed of a two degree-of-freedom mass-spring system with quadratic elastic nonlinearity. The possibility of converting, during the reflection process, most of the fundamental incoming wave energy into the second harmonic wave is shown, both theoretically and numerically, by means of a proper design of the nonlinear metasurface. The theoretical results from the harmonic balance method for a monochromatic source are compared with time domain simulations for a wave packet source. This protocol allows analyzing the dynamics of the nonlinear reflection process in the metasurface as well as exploring the limits of the operating frequency bandwidth. The reported methodology can be applied to a wide variety of nonlinear metasurfaces, thus possibly extending the family of exotic nonlinear reflection processes.

Compton Reflection in AGN with Simbol-X

Science.gov (United States)

Beckmann, V.; Courvoisier, T. J.-L.; Gehrels, N.; Lubiński, P.; Malzac, J.; Petrucci, P. O.; Shrader, C. R.; Soldi, S.

2009-05-01

AGN exhibit complex hard X-ray spectra. Our current understanding is that the emission is dominated by inverse Compton processes which take place in the corona above the accretion disk, and that absorption and reflection in a distant absorber play a major role. These processes can be directly observed through the shape of the continuum, the Compton reflection hump around 30 keV, and the iron fluorescence line at 6.4 keV. We demonstrate the capabilities of Simbol-X to constrain complex models for cases like MCG-05-23-016, NGC 4151, NGC 2110, and NGC 4051 in short (10 ksec) observations. We compare the simulations with recent observations on these sources by INTEGRAL, Swift and Suzaku. Constraining reflection models for AGN with Simbol-X will help us to get a clear view of the processes and geometry near to the central engine in AGN, and will give insight to which sources are responsible for the Cosmic X-ray background at energies >20 keV.

Characterizing the reflectivity of handheld display devices.

Science.gov (United States)

Liu, Peter; Badano, Aldo

2014-08-01

With increased use of handheld and tablet display devices for viewing medical images, methods for consistently measuring reflectivity of the devices are needed. In this note, the authors report on the characterization of diffuse reflections for handheld display devices including mobile phones and tablets using methods recommended by the American Association of Physicists in Medicine Task Group 18 (TG18). The authors modified the diffuse reflectance coefficient measurement method outlined in the TG18 report. The authors measured seven handheld display devices (two phones and five tablets) and three workstation displays. The device was attached to a black panel with Velcro. To study the effect of the back surface on the diffuse reflectance coefficient, the authors created Styrofoam masks with different size square openings and placed it in front of the device. Overall, for each display device, measurements of illuminance and reflected luminance on the display screen were taken. The authors measured with no mask, with masks of varying size, and with display-size masks, and calculated the corresponding diffuse reflectance coefficient. For all handhelds, the diffuse reflectance coefficient measured with no back panel were lower than measurements performed with a mask. The authors found an overall increase in reflectivity as the size of the mask decreases. For workstations displays, diffuse reflectance coefficients were higher when no back panel was used, and higher than with masks. In all cases, as luminance increased, illuminance increased, but not at the same rate. Since the size of handheld displays is smaller than that of workstation devices, the TG18 method suffers from a dependency on illumination condition. The authors show that the diffuse reflection coefficients can vary depending on the nature of the back surface of the illuminating box. The variability in the diffuse coefficient can be as large as 20% depending on the size of the mask. For all measurements

Coal rank (vitrinite reflectance) data for Cretaceous/Tertiary coal measures in the Grande Cache and Hinton areas, Alberta

Energy Technology Data Exchange (ETDEWEB)

Kalkreuth, W.D.; Langenberg, W.; McMechan, M.E.; Tomica, M.A.; McDougall, W.; Burchard, K.

1996-07-01

A total of 544 vitrinite reflectance values are reported. The outcrop locations and other pertinent data are listed. Vitrinite reflectances determined in subsurface samples from two coal exploration boreholes and 13 petroleum exploration wells are tabulated. The data have been used (in other studies) to evaluate maturation levels in potential source rocks and to assess methane potential of the coal deposits. A diskette containing the data is included. 18 refs., 1 fig., 2 tabs.

DOA Estimation of Audio Sources in Reverberant Environments

DEFF Research Database (Denmark)

Jensen, Jesper Rindom; Nielsen, Jesper Kjær; Heusdens, Richard

2016-01-01

Reverberation is well-known to have a detrimental impact on many localization methods for audio sources. We address this problem by imposing a model for the early reflections as well as a model for the audio source itself. Using these models, we propose two iterative localization methods...... that estimate the direction-of-arrival (DOA) of both the direct path of the audio source and the early reflections. In these methods, the contribution of the early reflections is essentially subtracted from the signal observations before localization of the direct path component, which may reduce the estimation...

INFLUENCE OF THE ORTHOGONALLY POLARIZED BACK REFLECTIONS ON THE POWER AND RADIATION SPECTRUM OF SUPERLUMINESCENT DIODES

Directory of Open Access Journals (Sweden)

A. B. Mukhtubayev

2015-01-01

Full Text Available We have investigated the back reflections influence on the spectrum for optical radiation source of superluminescent diode type and have provided optimal operating conditions of the radiation source. The feature of the research method is the usage of a fiber polarization controller and an optical mirror coated on the end of an optical fiber. The studies were conducted with two sources of optical radiation: ThorLabs superluminescent diode series S5FC1005SXL and LED module ELED-1550-1-E-9-SM1-FA-CW. It was revealed that at the value of back reflections equal to -13 dB relative to the output power source, a negative impact on power and spectral characteristics of the source with an optical power of 2.3 µW is beginning to appear. It was also confirmed that at the increase of the radiation power by increasing the source pumping current, back reflection influence is exhibiting at a lower level of back reflections. The results obtained need to be considered when designing fiber optic sensors in order to eliminate the effect of back reflections on the sources of optical radiation having been studied in this paper.

Teens Reflect on Their Sources of Contraceptive Information

Science.gov (United States)

Jones, Rachel K.; Biddlecom, Ann E.; Hebert, Luciana; Mellor, Ruth

2011-01-01

Based on semistructured interviews with a racially and ethnically diverse sample of 58 U.S. high school students, this study examines teens' exposure to contraceptive information from a range of sources and the extent to which they trust this information. Teens report exposure to contraceptive information from many individuals and places, most…

Annual Reports: Preserving and Disseminating a Source for Business History

Science.gov (United States)

Cronin-Kardon, Cynthia L.; Halperin, Michael

2007-01-01

Lippincott Library's Historical Corporate Annual Reports Collection contains useful primary sources of information for several disciplines, including applied accounting and business history. They also are reflections of the societal and cultural mores of the times. Unfortunately, these reports are fragile, difficult to locate, and hard to access.…

Seasonal soybean crop reflectance

Science.gov (United States)

Lemaster, E. W. (Principal Investigator); Chance, J. E.

1983-01-01

Data are presented from field measurements of 1980 including 5 acquisitions of handheld radiometer reflectance measurements, 7 complete sets of parameters for implementing the Suits mode, and other biophysical parameters to characterize the soybean canopy. LANDSAT calculations on the simulated Brazilian soybean reflectance are included along with data collected during the summer and fall on 1981 on soybean single leaf optical parameters for three irrigation treatments. Tests of the Suits vegetative canopy reflectance model for the full hemisphere of observer directions as well as the nadir direction show moderate agreement for the visible channels of the MSS and poor agreement in the near infrared channel. Temporal changes in the spectral characteristics of the single leaves were seen to occur as a function of maturity which demonstrates that the absorptance of a soybean single leaf is more a function of thetransmittancee characteristics than the seasonally consistent single leaf reflectance.

Reflective Practice: Origins and Interpretations

Science.gov (United States)

Reynolds, Michael

2011-01-01

The idea of reflection is central to the theory and practice of learning--especially learning which is grounded in past or current experience. This paper proposes a working definition of reflection and reviews its origins and recent developments. The author also provides an account of "critical reflection", including its rationale and…

A Method of Retrieving BRDF from Surface-Reflected Radiance Using Decoupling of Atmospheric Radiative Transfer and Surface Reflection

Directory of Open Access Journals (Sweden)

Alexander Radkevich

2018-04-01

Full Text Available Bi-directional reflection distribution function (BRDF defines anisotropy of the surface reflection. It is required to specify the boundary condition for radiative transfer (RT modeling used in aerosol retrievals, cloud retrievals, atmospheric modeling, and other applications. Ground based measurements of reflected radiance draw increasing attention as a source of information about anisotropy of surface reflection. Derivation of BRDF from surface radiance requires atmospheric correction. This study develops a new method of retrieving BRDF on its whole domain, making it immediately suitable for further atmospheric RT modeling applications. The method is based on the integral equation relating surface-reflected radiance, BRDF, and solutions of two auxiliary atmosphere-only RT problems. The method requires kernel-based BRDF. The weights of the kernels are obtained with a quickly converging iterative procedure. RT modeling has to be done only one time before the start of iterative process.

Dissenting in Reflective Conversations

DEFF Research Database (Denmark)

Bjørn, Pernille; Boulus, Nina

2011-01-01

Reflective monitoring of research practices is essential. However, we often lack formal training in the practices of doing action research, and descriptions of actual inquiry practice are seldom included in publications. Our aim is to provide a glimpse of self-reflective practices based on our...

Recent advancements in sputter-type heavy negative ion sources

International Nuclear Information System (INIS)

Alton, G.D.

1989-01-01

Significant advancement have been made in sputter-type negative ion sources which utilize direct surface ionization, or a plasma to form the positive ion beam used to effect sputtering of samples containing the material of interest. Typically, such sources can be used to generate usable beam intensities of a few μA to several mA from all chemically active elements, depending on the particular source and the electron affinity of the element in question. The presentation will include an introduction to the fundamental processes underlying negative ion formation by sputtering from a low work function surface and several sources will be described which reflect the progress made in this technology. 21 refs., 9 figs., 1 tab

Total-reflection x-ray fluorescence with a brillant undulator x-ray source

International Nuclear Information System (INIS)

Sakurai, K.; Eba, H.; Numako, C.; Suzuki, M.; Inoue, K.; Yagi, N.

2000-01-01

Total-reflection x-ray fluorescence (TXRF) is a highly sensitive technique for analyzing trace elements, because of the very low background from the sample support. Use of third-generation synchrotron x-ray source could further enhance the detection power. However, while such high sensitivity permits the detection of signals from trace elements of interest, it also means that one can observe weak parasitic x-rays as well. If the sample surface becomes even slightly contaminated, owing to air particulates near the beamline, x-ray fluorescence lines of iron, zinc, copper, nickel, chromium, and titanium can be observed even for a blank sample. Another critical problem is the low-energy-side tail of the scattering x-rays, which ultimately restricts the detection capability of the technique using a TXRF spectrometer based on a Si(Li) detector. The present paper describes our experiments with brilliant undulator x-ray beams at BL39XU and BL40XU, at the SPring-8, Harima, Japan. The emphasis is on the development of instruments to analyze a droplet of 0.1 μl containing trace elements of ppb level. Although the beamline is not a clean room, we have employed equipment for preparing a clean sample and also for avoiding contamination during transferring the sample into the spectrometer. We will report on the successful detection of the peak from 0.8 ppb selenium in a droplet (absolute amount 80 fg). We will also present the results of recent experiments obtained from a Johansson spectrometer rather than a Si(Li) detector. (author)

Options for the Delft advanced neutron source

International Nuclear Information System (INIS)

Gibcus, H.P.M.; Leege, P.F.A. de; Labohm, F.; Vries, J.W. de; Verkooijen, A.H.M.; Valko, J.; Feltes, W.; Heinecke, J.

2003-01-01

Results of feasibility studies are presented for options for an advanced neutron source for the Delft reactor including upgrading the HOR, a 2 MW pool-type research reactor at the Delft University of Technology. The primary utilisation of the HOR focuses on beam research applications with neutrons and positrons. The aim of being scientifically competitive in that research area requires a thermal neutron flux level of at least 1x10 14 n/cm 2 /s. The feasibility of an accelerator driven neutron source and upgrading the present core to a super compact core for reaching this goal has been investigated at large from a safety and operational point of view. For the upgraded core, a 3x3 fuel assembly arrangement and beryllium reflected at all sides was chosen. Figures on the system performance, including the merits of a cold neutron source application feeding the neutron guide system, are presented. (author)

The Advanced Neutron Source liquid deuterium cold source

International Nuclear Information System (INIS)

Lucas, A.T.

1995-08-01

The Advanced Neutron Source will employ two cold sources to moderate neutrons to low energy (<10 meV). The cold neutrons produced are then passed through beam guides to various experiment stations. Each cold source moderator is a sphere of 410-mm internal diameter. The moderator material is liquid deuterium flowing at a rate of 1 kg/s and maintained at subcooled temperatures at all points of the circuit, to prevent boiling. Nuclear beat deposited within the liquid deuterium and its containment structure totals more than 30 kW. All of this heat is removed by the liquid deuterium, which raises its temperature by 5 K. The liquid prime mover is a cryogenic circulator that is situated in the return leg of the flow loop. This arrangement minimizes the heat added to the liquid between the heat exchanger and the moderator vessel, allowing the moderator to be operated at the minimum practical temperature. This report describes the latest thinking at the time of project termination. It also includes the status of various systems at that time and outlines anticipated directions in which the design would have progressed. In this regard, some detail differences between this report and official design documents reflect ideas that were not approved at the time of closure but are considered noteworthy

Enhancing Self-Practice/Self-Reflection (SP/SR) approach to cognitive behaviour training through the use of reflective blogs.

Science.gov (United States)

Farrand, Paul; Perry, Jon; Linsley, Sue

2010-07-01

Self-Practice/Self-Reflection (SP/SR) is increasingly beginning to feature as a central component of CBT training programmes (Bennett-Levy et al., 2001). Programmes including a reflective element, however, are not unproblematic and it has been documented that simply setting time aside for reflection does not necessarily result in trainees using such time to reflect. Such limitations may be overcome by including a requirement to post reflections on reflective blogs. To examine the effect that a requirement to contribute to a reflective blog had upon a SP/SR approach to CBT training. A focus group methodology was adopted with data analyzed using a general inductive qualitative approach. The requirement to use blogs to reflect upon the self-practice of CBT techniques enhanced SP/SR, established a learning community, and improved course supervision, although some technical difficulties arose. Consideration should be given towards using reflective blogs to support a SP/SR approach to CBT training. Benefits afforded by the use of reflective blogs further establish SP/SR as a valid and flexible training approach.

Reflecting reflection in supervision

DEFF Research Database (Denmark)

Lystbæk, Christian Tang

associated with reflection and an exploration of alternative conceptions that view reflection within the context of settings which have a more group- and team-based orientation. Drawing on an action research project on health care supervision, the paper questions whether we should reject earlier views...... of reflection, rehabilitate them in order to capture broader connotations or move to new ways of regarding reflection that are more in keeping with not only reflective but also emotive, normative and formative views on supervision. The paper presents a critical perspective on supervision that challenge...... the current reflective paradigm I supervision and relate this to emotive, normative and formative views supervision. The paper is relevant for Nordic educational research into the supervision and guidance...

Energy-Water Nexus Relevant to Baseload Electricity Source Including Mini/Micro Hydropower Generation

Science.gov (United States)

Fujii, M.; Tanabe, S.; Yamada, M.

2014-12-01

Water, food and energy is three sacred treasures that are necessary for human beings. However, recent factors such as population growth and rapid increase in energy consumption have generated conflicting cases between water and energy. For example, there exist conflicts caused by enhanced energy use, such as between hydropower generation and riverine ecosystems and service water, between shale gas and ground water, between geothermal and hot spring water. This study aims to provide quantitative guidelines necessary for capacity building among various stakeholders to minimize water-energy conflicts in enhancing energy use. Among various kinds of renewable energy sources, we target baseload sources, especially focusing on renewable energy of which installation is required socially not only to reduce CO2 and other greenhouse gas emissions but to stimulate local economy. Such renewable energy sources include micro/mini hydropower and geothermal. Three municipalities in Japan, Beppu City, Obama City and Otsuchi Town are selected as primary sites of this study. Based on the calculated potential supply and demand of micro/mini hydropower generation in Beppu City, for example, we estimate the electricity of tens through hundreds of households is covered by installing new micro/mini hydropower generation plants along each river. However, the result is based on the existing infrastructures such as roads and electric lines. This means that more potentials are expected if the local society chooses options that enhance the infrastructures to increase micro/mini hydropower generation plants. In addition, further capacity building in the local society is necessary. In Japan, for example, regulations by the river law and irrigation right restrict new entry by actors to the river. Possible influences to riverine ecosystems in installing new micro/mini hydropower generation plants should also be well taken into account. Deregulation of the existing laws relevant to rivers and

Reflective Practices for Teacher Education

Directory of Open Access Journals (Sweden)

Paulus Kuswandono

2017-01-01

Full Text Available Studies on reflective practice in teacher education are increasingly getting more attention at least in the last 2 decades. This article discusses concepts of reflection and how it is implemented in educating pre-service teachers on their early stage of professional learning. The purposes of doing the reflection for pre-service teachers are not only for illuminating their professional learning experiences, but also to critically reflect their vocation as teachers, including the values which may be dictated to them through rigid regulations. Reflection in teacher education is crucial as it connects well with learning in that learners use reflection to exercise their mind and to evaluate their learning experiences. Besides, this article also highlights some perceived difficulties to implement reflective practice, as well as ways how to promote reflection.   DOI: https://doi.org/10.24071/llt.2012.150102

Source-driven noise analysis measurements with neptunium metal reflected by high enriched uranium

International Nuclear Information System (INIS)

Valentine, Timothy E.; Mattingly, John K.

2003-01-01

Subcritical noise analysis measurements have been performed with neptunium ( 237 Np) sphere reflected by highly enriched uranium. These measurements were performed at the Los Alamos Critical Experiment Facility in December 2002 to provide an estimate of the subcriticality of 237 Np reflected by various amounts of high-enriched uranium. This paper provides a description of the measurements and presents some preliminary results of the analysis of the measurements. The measured and calculated spectral ratios differ by 15% whereas the 'interpreted' and calculated k eff values differ by approximately 1%. (author)

Reflection of oblique electron thermal modes in an inhomogeneous plasma

International Nuclear Information System (INIS)

Ohnuma, T.; Watanabe, T.; Sanuki, H.

1980-04-01

In an inhomogeneous magnetoplasma, reflection of an oblique electron thermal mode radiated from a local source is investigated experimentally and theoretically near the electron plasma frequency layer. The experimental observation of reflection in the lower plasma density region than the f sub(p)-layer is found to be in qualitative accord with the theoretical reflection, which is obtained from a kinetic theory in an inhomogeneous magnetoplasma. The reflection of the thermal mode is also compared with that of an electromagnetic mode at the f sub(p)-layer. (author)

Reflection Spectra of the Black Hole Binary Candidate MAXI J1535-571 in the Hard State Observed by NuSTAR

Science.gov (United States)

Xu, Yanjun; Harrison, Fiona A.; García, Javier A.; Fabian, Andrew C.; Fürst, Felix; Gandhi, Poshak; Grefenstette, Brian W.; Madsen, Kristin K.; Miller, Jon M.; Parker, Michael L.; Tomsick, John A.; Walton, Dominic J.

2018-01-01

We report on a Nuclear Spectroscopic Telescope Array (NuSTAR) observation of the recently discovered bright black hole candidate MAXI J1535-571. NuSTAR observed the source on MJD 58003 (five days after the outburst was reported). The spectrum is characteristic of a black hole binary in the hard state. We observe clear disk reflection features, including a broad Fe Kα line and a Compton hump peaking around 30 keV. Detailed spectral modeling reveals a narrow Fe Kα line complex centered around 6.5 keV on top of the strong relativistically broadened Fe Kα line. The narrow component is consistent with distant reflection from moderately ionized material. The spectral continuum is well described by a combination of cool thermal disk photons and a Comptonized plasma with the electron temperature {{kT}}{{e}}=19.7+/- 0.4 keV. An adequate fit can be achieved for the disk reflection features with a self-consistent relativistic reflection model that assumes a lamp-post geometry for the coronal illuminating source. The spectral fitting measures a black hole spin a> 0.84, inner disk radius {R}{in}lamp-post height h={7.2}-2.0+0.8 {r}{{g}} (statistical errors, 90% confidence), indicating no significant disk truncation and a compact corona. Although the distance and mass of this source are not currently known, this suggests the source was likely in the brighter phases of the hard state during this NuSTAR observation.

Transmission versus reflectance spectroscopy for quantitation

Science.gov (United States)

Gardner, Craig M.

2018-01-01

The objective of this work was to compare the accuracy of analyte concentration estimation when using transmission versus diffuse reflectance spectroscopy of a scattering medium. Monte Carlo ray tracing of light through the medium was used in conjunction with pure component absorption spectra and Beer-Lambert absorption along each ray's pathlength to generate matched sets of pseudoabsorbance spectra, containing water and six analytes present in skin. PLS regression models revealed an improvement in accuracy when using transmission compared to reflectance for a range of medium thicknesses and instrument noise levels. An analytical expression revealed the source of the accuracy degradation with reflectance was due both to the reduced collection efficiency for a fixed instrument etendue and to the broad pathlength distribution that detected light travels in the medium before exiting from the incident side.

Demystifying the reflective clinical journal

International Nuclear Information System (INIS)

Milinkovic, Danielle; Field, Nikki

2005-01-01

Student learning on clinical placement is a complex issue and cannot be defined solely by just doing things. Reflection during clinical practice is essential if the student is going to learn from the experience. Therefore it is important for educators to include as part of clinical education programs learning strategies that encourage reflection. The reflective clinical journal is an educational tool that is employed by the School of Medical Radiation Sciences at the University of Sydney to encourage reflection of undergraduate radiation therapy students whilst on clinical placement. This discussion paper explores the key concepts of reflection and the reflective clinical journal. Due to the paucity of information about this issue in radiation therapy the literature reviewed is from across all areas of the health sciences

Sputtering and reflection of self-bombardment of tungsten material

International Nuclear Information System (INIS)

Niu, Guo-jian; Li, Xiao-chun; Xu, Qian; Yang, Zhong-shi; Luo, Guang-nan

2015-01-01

In present research, the sputtering and reflection yield of self-bombardment of tungsten are investigated with the aid of molecular dynamics simulations. The source of sputtered and reflected atoms is detected by traced the original locations of sputtered and reflected atoms. Results show that for the reflected atoms no specific region exists which means cluster atoms are randomly reflected. But almost all of sputtered atoms are from a conical region under the landing point of cluster. So we can determine the sputtering yield by study the dimension of the sputtering region. Molecular dynamics shows the depth and radius of the conical are power functions of impacting energy. The effects of cluster size and temperature of target on sputtering and reflection rate are also preformed in present study. Both sputtering and reflection yield are proportion to cluster size in present cluster size, i.e. 66–2647 atoms. Higher target temperature can increase sputtering yield and deduce sputtering threshold energy, but little effect on reflection rate

Sputtering and reflection of self-bombardment of tungsten material

Energy Technology Data Exchange (ETDEWEB)

Niu, Guo-jian [University of Science and Technology of China, Hefei (China); Institute of Plasma Physics Chinese Academy of Sciences, Hefei (China); Li, Xiao-chun; Xu, Qian; Yang, Zhong-shi [Institute of Plasma Physics Chinese Academy of Sciences, Hefei (China); Luo, Guang-nan, E-mail: gnluo@ipp.ac.cn [University of Science and Technology of China, Hefei (China); Institute of Plasma Physics Chinese Academy of Sciences, Hefei (China); Hefei Center for Physical Science and Technology, Hefei (China); Hefei Science Center of CAS, Hefei (China)

2015-04-15

In present research, the sputtering and reflection yield of self-bombardment of tungsten are investigated with the aid of molecular dynamics simulations. The source of sputtered and reflected atoms is detected by traced the original locations of sputtered and reflected atoms. Results show that for the reflected atoms no specific region exists which means cluster atoms are randomly reflected. But almost all of sputtered atoms are from a conical region under the landing point of cluster. So we can determine the sputtering yield by study the dimension of the sputtering region. Molecular dynamics shows the depth and radius of the conical are power functions of impacting energy. The effects of cluster size and temperature of target on sputtering and reflection rate are also preformed in present study. Both sputtering and reflection yield are proportion to cluster size in present cluster size, i.e. 66–2647 atoms. Higher target temperature can increase sputtering yield and deduce sputtering threshold energy, but little effect on reflection rate.

Reflective Occultation Mask for Evaluation of Occulter Designs for Planet Finding

Science.gov (United States)

Hagopian, John; Lyon, Richard; Shiri, Shahram; Roman, Patrick

2011-01-01

Advanced formation flying occulter designs utilize a large occulter mask flying in formation with an imaging telescope to block and null starlight to allow imaging of faint planets in exosolar systems. A paper describes the utilization of subscale reflective occultation masks to evaluate formation flying occulter designs. The use of a reflective mask allows mounting of the occulter by conventional means and simplifies the test configuration. The innovation alters the test set-up to allow mounting of the mask using standard techniques to eliminate the problems associated with a standard configuration. The modified configuration uses a reflective set-up whereby the star simulator reflects off of a reflective occulting mask and into an evaluation telescope. Since the mask is sized to capture all rays required for the imaging test, it can be mounted directly to a supporting fixture without interfering with the beam. Functionally, the reflective occultation mask reflects light from the star simulator instead of transmitting it, with a highly absorptive carbon nanotube layer simulating the occulter blocking mask. A subscale telescope images the star source and companion dim source that represents a planet. The primary advantage of this is that the occulter can be mounted conventionally instead of using diffractive wires or magnetic levitation.

Berlin Reflectance Spectral Library (BRSL)

Science.gov (United States)

Henckel, D.; Arnold, G.; Kappel, D.; Moroz, L. V.; Markus, K.

2017-09-01

The Berlin Reflectance Spectral Library (BRSL) provides a collection of reflectance spectra between 0.3 and 17 µm. It was originally dedicated to support space missions to small solar system bodies. Meanwhile the library includes selections of biconical reflectance spectra for spectral data analysis of other planetary bodies as well. The library provides reference spectra of well-characterized terrestrial analogue materials and meteorites for interpretation of remote sensing reflectance spectra of planetary surfaces. We introduce the BRSL, summarize the data available, and access to use them for further relevant applications.

Palynofacies assemblages reflect sources of organic matter in New Zealand fjords

Science.gov (United States)

Prebble, Joseph G.; Hinojosa, Jessica L.; Moy, Christopher M.

2018-02-01

Understanding sources and transport pathways of organic carbon in fjord systems is important to quantify carbon cycling in coastal settings. Provenance of surficial sediment organic carbon in Fiordland National Park (southwestern New Zealand) has previously been estimated using a range of techniques, including mixing models derived from stable isotopes and lipid biomarker distributions. Here, we present the first application of palynofacies to explore the sources of particulate organic carbon to five fjords along the SW margin of New Zealand, to further discriminate the provenance of organic carbon in the fjords. We find good correlation between isotopic-and biomarker-derived proxies for organic carbon provenance and our new palynofacies observations. We observe strong down-fjord gradients of decreasing terrestrially derived organic carbon further from the river inflow at fjord heads. Fjords with small catchments and minor fresh water inflow exhibit reversed gradients, indicating that volume of freshwater entering at the fjord head is a primary mechanism to transport particulates down fjord rather than local transport from fjord sides. The palynofacies data also confirmed previously recorded latitudinal trends (i.e. between fjords), of less frequent and more weathered terrestrially derived organic carbon in the southern fjords, consistent with enhanced marine inflow and longer transport times in the southern catchments. Dinocyst assemblages also exhibit a strong latitudinal gradient, with assemblages dominated by heterotrophic forms in the north. In addition to providing support for previous studies, this approach allows finer discrimination of terrestrial organic carbon than previously, for example variation of leaf material. This study demonstrates that visual palynofacies analysis is a valuable tool to pinpoint origins of organic carbon in fjord systems, providing different but complementary information to other proxies.

The value of reflective journaling in undergraduate nursing education: a literature review.

Science.gov (United States)

Epp, Sheila

2008-09-01

The purpose of this literature review was to ascertain the evidence for the use of reflective journaling as a tool to promote the pedagogical strategy of reflection for the purpose of learning from practice for practice in undergraduate nursing education. Concept-centric. The literature review involved structured searches of all OVID gateway databases, EBSCO host databases, and Blackwell Synergy. Qualitative and Quantitative Studies from 1992 to 2006 were included if they focused on reflective journaling in undergraduate clinical education. Due to the vast plethora of literature on reflection, keywords were utilized to focus the search. Approximately 150 abstracts were reviewed for primary sources of research. A total of nine studies met the inclusion criteria. The review subsequently divided the literature into four content themes allowing for appraisal and analysis of the findings, followed by summary and key recommendations for nursing education and research. There was evidence that educators struggle to incorporate reflective processes into education; however, the research provided rationale and support for engaging undergraduate students in the reflective process. Researchers found reasonable levels of reflection in undergraduate students' journaling and educators reported students' learning as a result of reflective journaling. Further to this, there was evidence that writing reflectively improved over time; a learned skill also dependent on a good facilitator and trust. Unfortunately, there was a paucity of research that explored the undergraduate nurses' experiences with the process of having to create written communication, with a critical reflective focus on practice. Nursing educators are correct in pursuing the teaching and learning of the reflective process in undergraduate nursing education. Nurse educators need to utilize various tools and strategies for facilitating the growth of undergraduate students into reflective practitioners. Indeed there was

Reflective article having a sacrificial cathodic layer

Science.gov (United States)

Kabagambe, Benjamin; Buchanan, Michael J.; Scott, Matthew S.; Rearick, Brian K.; Medwick, Paul A.; McCamy, James W.

2017-09-12

The present invention relates to reflective articles, such as solar mirrors, that include a sacrificial cathodic layer. The reflective article, more particularly includes a substrate, such as glass, having a multi-layered coating thereon that includes a lead-free sacrificial cathodic layer. The sacrificial cathodic layer includes at least one transition metal, such as a particulate transition metal, which can be in the form of flakes (e.g., zinc flakes). The sacrificial cathodic layer can include an inorganic matrix formed from one or more organo-titanates. Alternatively, the sacrificial cathodic layer can include an organic polymer matrix (e.g., a crosslinked organic polymer matrix formed from an organic polymer and an aminoplast crosslinking agent). The reflective article also includes an outer organic polymer coating, that can be electrodeposited over the sacrificial cathodic layer.

Reconstruction of reflectance data using an interpolation technique.

Science.gov (United States)

Abed, Farhad Moghareh; Amirshahi, Seyed Hossein; Abed, Mohammad Reza Moghareh

2009-03-01

A linear interpolation method is applied for reconstruction of reflectance spectra of Munsell as well as ColorChecker SG color chips from the corresponding colorimetric values under a given set of viewing conditions. Hence, different types of lookup tables (LUTs) have been created to connect the colorimetric and spectrophotometeric data as the source and destination spaces in this approach. To optimize the algorithm, different color spaces and light sources have been used to build different types of LUTs. The effects of applied color datasets as well as employed color spaces are investigated. Results of recovery are evaluated by the mean and the maximum color difference values under other sets of standard light sources. The mean and the maximum values of root mean square (RMS) error between the reconstructed and the actual spectra are also calculated. Since the speed of reflectance reconstruction is a key point in the LUT algorithm, the processing time spent for interpolation of spectral data has also been measured for each model. Finally, the performance of the suggested interpolation technique is compared with that of the common principal component analysis method. According to the results, using the CIEXYZ tristimulus values as a source space shows priority over the CIELAB color space. Besides, the colorimetric position of a desired sample is a key point that indicates the success of the approach. In fact, because of the nature of the interpolation technique, the colorimetric position of the desired samples should be located inside the color gamut of available samples in the dataset. The resultant spectra that have been reconstructed by this technique show considerable improvement in terms of RMS error between the actual and the reconstructed reflectance spectra as well as CIELAB color differences under the other light source in comparison with those obtained from the standard PCA technique.

Phase resolved and coherence gated en face reflection imaging of multilayered embryonal carcinoma cells

Science.gov (United States)

Yamauchi, Toyohiko; Fukami, Tadashi; Iwai, Hidenao; Yamashita, Yutaka

2012-03-01

Embryonal carcinoma (EC) cells, which are cell lines derived from teratocarcinomas, have characteristics in common with stem cells and differentiate into many kinds of functional cells. Similar to embryonic stem (ES) cells, undifferentiated EC cells form multi-layered spheroids. In order to visualize the three-dimensional structure of multilayered EC cells without labeling, we employed full-field interference microscopy with the aid of a low-coherence quantitative phase microscope, which is a reflection-type interference microscope employing the digital holographic technique with a low-coherent light source. Owing to the low-coherency of the light-source (halogen lamp), only the light reflected from reflective surface at a specific sectioning height generates an interference image on the CCD camera. P19CL6 EC cells, derived from mouse teratocarcinomas, formed spheroids that are about 50 to 200 micrometers in diameter. Since the height of each cell is around 10 micrometers, it is assumed that each spheroid has 5 to 20 cell layers. The P19CL6 spheroids were imaged in an upright configuration and the horizontally sectioned reflection images of the sample were obtained by sequentially and vertically scanning the zero-path-length height. Our results show the threedimensional structure of the spheroids, in which plasma and nuclear membranes were distinguishably imaged. The results imply that our technique is further capable of imaging induced pluripotent stem (iPS) cells for the assessment of cell properties including their pluripotency.

Compact X-ray sources: X-rays from self-reflection

Science.gov (United States)

Mangles, Stuart P. D.

2012-05-01

Laser-based particle acceleration offers a way to reduce the size of hard-X-ray sources. Scientists have now developed a simple scheme that produces a bright flash of hard X-rays by using a single laser pulse both to generate and to scatter an electron beam.

Macro Photography for Reflectance Transformation Imaging: A Practical Guide to the Highlights Method

Directory of Open Access Journals (Sweden)

Antonino Cosentino

2014-11-01

Full Text Available Reflectance Transformation Imaging (RTI is increasingly being used for art documentation and analysis and it can be successful also for the examination of features on the order of hundreds of microns. This paper evaluates some macro scale photography methods specifically for RTI employing the Highlights method for documenting sub-millimeter details. This RTI technique consists in including one reflective sphere in the scene photographed so that the processing software can calculate for each photo the direction of the light source from its reflection on the sphere. RTI documentation can be performed also with an RTI dome, but the Highlights method is preferred because is more mobile and more affordable. This technique is demonstrated in the documentation of some prints ranging from the XV to the XX century from to the Ingels collection in Sweden. The images are here examined and discussed, showing the application of macro RTI for identifying features of prints.

Reflectance spectroscopy and asteroid surface mineralogy

International Nuclear Information System (INIS)

Gaffey, M.J.; Bell, J.F.; Cruikshank, D.P.

1989-01-01

Information available from reflectance spectroscopy on the surface mineralogy of asteroids is discussed. Current spectral interpretive procedures used in the investigations of asteroid mineralogy are described. Present understanding of the nature and history of asteroids is discussed together with some still unresolved issues such as the source of ordinary chondrites. 100 refs

Methodological Reflections: Inter- ethnic Research

DEFF Research Database (Denmark)

Singla, Rashmi

2010-01-01

with both youth and the parental generation with ethnic minority background in Denmark. These reflections include implications and challenges related to researcher’s national, ethnic background and educational, professional position in encounter with   diverse ‘researched persons’ such as youth......This article reflects on the methodological and epistemological aspects of the ethical issues involved in encounters between researcher and research participants with ethnic minority background in contexts with diversity. Specific challenges involved in longitudinal research (10 - 15 years......) are also considered. The issues related to the social relevance of the research deriving from psycho political validity implying consideration of power dynamics in the personal, relational and collective domains are included. The primary basis for these reflections is a follow-up study concerning young...

Reflection seismic investigations of western Canadian coalfields. Final report

Energy Technology Data Exchange (ETDEWEB)

Lawton, D.C.; Bertram, M.B.

1983-03-01

High resolution reflection seismic studies using a seisgun surface source were undertaken at four sites in Alberta. The objective of the project was to test the feasibility of the seismic method for the exploration and evaluation of coal deposits in a range of environments in western Canada. At Camrose, coherent reflections from a coal zone 70-110 m below the surface were recorde along a 5 km profile. Variations in reflection amplitude and character were interpreted in terms of two main seams. Channel washouts, faults with throws of 5 m or greater, and effects of differential compaction were resolved. Studies at a foothills site showed that good data can be obtained in structurally disturbed areas with mild deformation. At this site, faults with vertical throws of up to 40 m were delineated. In the mountain region, studies indicated that the seismic method is not appropriate in areas with strong deformation. Deep weathering, variable topography and rapid lateral changes in reflector dip were the main reasons for poor data quality. The seisgun is a threshold seismic source which performs well in areas with a shallow water table and a zone of interest within 350 m of the surface. Its effectiveness decreases dramatically if the overburden is both thick and dry. Careful selection of field geometry and recording parameters is critical. In data processing, important aspects are the careful muting of first breaks and evaluation of short and long wavelength weathering statics corrections. A computer program listing for static correction analysis is included. The seismic method is very appropriate for evaluation of Plains and Foothills coal deposits in Alberta. It can provide continuous subsurface coverage between drillholes and therefore reduce the density of drillholes required to delineate a prospective area. 29 refs., 33 figs., 2 tabs.

Validation of a spectral correction procedure for sun and sky reflections in above-water reflectance measurements.

Science.gov (United States)

Groetsch, Philipp M M; Gege, Peter; Simis, Stefan G H; Eleveld, Marieke A; Peters, Steef W M

2017-08-07

A three-component reflectance model (3C) is applied to above-water radiometric measurements to derive remote-sensing reflectance Rrs (λ). 3C provides a spectrally resolved offset Δ(λ) to correct for residual sun and sky radiance (Rayleigh- and aerosol-scattered) reflections on the water surface that were not represented by sky radiance measurements. 3C is validated with a data set of matching above- and below-water radiometric measurements collected in the Baltic Sea, and compared against a scalar offset correction Δ. Correction with Δ(λ) instead of Δ consistently reduced the (mean normalized root-mean-square) deviation between Rrs (λ) and reference reflectances to comparable levels for clear (Δ: 14.3 ± 2.5 %, Δ(λ): 8.2 ± 1.7 %), partly clouded (Δ: 15.4 ± 2.1 %, Δ(λ): 6.5 ± 1.4 %), and completely overcast (Δ: 10.8 ± 1.7 %, Δ(λ): 6.3 ± 1.8 %) sky conditions. The improvement was most pronounced under inhomogeneous sky conditions when measurements of sky radiance tend to be less representative of surface-reflected radiance. Accounting for both sun glint and sky reflections also relaxes constraints on measurement geometry, which was demonstrated based on a semi-continuous daytime data set recorded in a eutrophic freshwater lake in the Netherlands. Rrs (λ) that were derived throughout the day varied spectrally by less than 2 % relative standard deviation. Implications on measurement protocols are discussed. An open source software library for processing reflectance measurements was developed and is made publicly available.

X-ray reflectivity and surface roughness

International Nuclear Information System (INIS)

Ocko, B.M.

1988-01-01

Since the advent of high brightness synchrotron radiation sources there has been a phenomenal growth in the use of x-rays as a probe of surface structure. The technique of x-ray reflectivity is particularly relevant to electrochemists since it is capable of probing the structure normal to an electrode surface in situ. In this paper the theoretical framework for x-ray reflectivity is reviewed and the results from previous non-electrochemistry measurements are summarized. These measurements are from the liquid/air interface (CCl 4 ), the metal crystal vacuum interface (Au(100)), and from the liquid/solid interface(liquid crystal/silicon). 34 refs., 5 figs

Do site-specific radiocarbon measurements reflect localized distributions of 14C in biota inhabiting a wetland with point contamination sources?

Science.gov (United States)

Yankovich, T; King-Sharp, K J; Benz, M L; Carr, J; Killey, R W D; Beresford, N A; Wood, M D

2013-12-01

Duke Swamp is a wetland ecosystem that receives (14)C via a groundwater pathway originating from a waste management area on Atomic Energy Canada Limited's Chalk River Laboratories site. This groundwater reaches the surface of the swamp, resulting in relatively high (14)C levels over an area of 146 m(2). The objective of this study was to quantify (14)C concentrations in flora and fauna inhabiting areas of Duke Swamp over the gradient of (14)C activity concentrations in moss to determine whether (14)C specific activities in receptor biota reflect the localized nature of the groundwater source in the swamp. Representative receptor plants and animals, and corresponding air and soil samples were collected at six sites in Duke Swamp with (14)C specific activities in air that ranged from 1140 to 45,900 Bq/kg C. In general, it was found that specific activities of (14)C in biota tissues reflected those measured in environmental media collected from the same sampling site. The findings demonstrate that mosses could be used in monitoring programs to ensure protection of biota in areas with elevated (14)C, negating the need to capture and euthanize higher organisms. Copyright © 2013 Elsevier Ltd. All rights reserved.

Insight in schizophrenia: involvement of self-reflection networks?

Science.gov (United States)

van der Meer, Lisette; de Vos, Annerieke E; Stiekema, Annemarie P M; Pijnenborg, Gerdina H M; van Tol, Marie-José; Nolen, Willem A; David, Anthony S; Aleman, André

2013-11-01

Impaired insight is a common feature in psychosis and an important predictor of variables such as functional outcome, prognosis, and treatment adherence. A cognitive process that may underlie insight in psychosis is self-reflection, or the conscious evaluation of one's traits and characteristics. The current study aims to investigate the neural correlates of self-reflective processing and its relationship with insight in schizophrenia. Forty-seven schizophrenia patients and 21 healthy controls performed a self-reflection task in a functional magnetic resonance imaging (fMRI) scanner. The tasks comprised a self-reflection, close other-reflection, and a semantic (baseline) condition. Insight scores were obtained with the Schedule of Assessment of Insight Expanded. In addition, cognitive insight scores were obtained (Beck Cognitive Insight Scale [BCIS]). Schizophrenia patients demonstrated less activation in the posterior cingulate cortex in the self- and other-reflection conditions and less activation in the precuneus in the other-reflection condition compared with healthy controls. Better insight was associated with greater response in the inferior frontal gyrus, anterior insula, and inferior parietal lobule during self-reflection. In addition, better cognitive insight was associated with higher activation in ventromedial prefrontal cortex during self-reflection. In the current study, evidence for a relationship between self-reflection and insight in patients with schizophrenia was found in brain areas related to self-reflection, self/other distinction and source attribution. The findings support the rationale for a treatment that is currently under evaluation, which attempts to increase insight by enhancing self-reflection.

Automatic specular reflections removal for endoscopic images

Science.gov (United States)

Tan, Ke; Wang, Bin; Gao, Yuan

2017-07-01

Endoscopy imaging is utilized to provide a realistic view about the surfaces of organs inside the human body. Owing to the damp internal environment, these surfaces usually have a glossy appearance showing specular reflections. For many computer vision algorithms, the highlights created by specular reflections may become a significant source of error. In this paper, we present a novel method for restoration of the specular reflection regions from a single image. Specular restoration process starts with generating a substitute specular-free image with RPCA method. Then the specular removed image was obtained by taking the binary weighting template of highlight regions as the weighting for merging the original specular image and the substitute image. The modified template was furthermore discussed for the concealment of artificial effects in the edge of specular regions. Experimental results on the removal of the endoscopic image with specular reflections demonstrate the efficiency of the proposed method comparing to the existing methods.

Can curriculum managers' reflections produce new strategies ...

African Journals Online (AJOL)

Simon Bhekimuzi Khoza

2016-11-05

Nov 5, 2016 ... sources are defined as objects and people that communicate learning .... vision, where teachers/managers use reflections to critique their ... Accounting, English, Geography, History,. Afrikaans .... curriculum, which made us to realise [sic] that it is important to ..... and enduring concerns (2nd ed). Thousand ...

Layered magnets: polarized neutron reflection studies

Energy Technology Data Exchange (ETDEWEB)

Zabel, H; Schreyer, A [Ruhr-Univ. Bochum, Lehrstuhl fuer Experimentalphysik/Festkoerperphysik, Bochum (Germany)

1996-11-01

Neutron reflectivity measurements from extended surfaces, thin films and superlattices provide information on the chemical profile parallel to the film normal, including film thicknesses, average composition and interfacial roughness parameters. Reflectivity measurements with polarized neutrons are particularly powerful for analyzing the magnetic density profiles in thin films and superlattices in addition to chemical profiles. The basic theory of polarized neutron reflectivity is provided, followed by some examples and more recent applications concerning polarized neutron reflectivity studies from exchange coupled Fe/Cr superlattices. (author) 5 figs., 13 refs.

Towards a Theory of the Ecology of Reflection: Reflective Practice for Experiential Learning in Higher Education

Science.gov (United States)

Harvey, Marina; Coulson, Debra; McMaugh, Anne

2016-01-01

Reflective practice is widely adopted across the field of experience-based learning subjects in higher education, including practicums, work-integrated learning, internships, service learning and community participation. This adoption of reflective practice implies that it supports student learning through experience. When reviewing the evidence…

Wall reflection modeling for charge exchange recombination spectroscopy (CXRS) measurements on Textor and ITER

International Nuclear Information System (INIS)

Banerjee, Santanu; Vasu, P; Von Hellermann, M; Jaspers, R J E

2010-01-01

Contamination of optical signals by reflections from the tokamak vessel wall is a matter of great concern. For machines such as ITER and future reactors, where the vessel wall will be predominantly metallic, this is potentially a risk factor for quantitative optical emission spectroscopy. This is, in particular, the case when bremsstrahlung continuum radiation from the bulk plasma is used as a common reference light source for the cross-calibration of visible spectroscopy. In this paper the reflected contribution to the continuum level in Textor and ITER has been estimated for the detection channels meant for charge exchange recombination spectroscopy (CXRS). A model assuming diffuse reflection has been developed for the bremsstrahlung which is a much extended source. Based on this model, it is shown that in the case of ITER upper port 3, a wall with a moderate reflectivity of 20% leads to the wall reflected fraction being as high as 55-60% of the weak signals in the edge channels. In contrast, a complete bidirectional reflectance distribution function (BRDF) based model has been developed in order to estimate the reflections from more localized sources like the charge exchange (CX) emission from a neutral beam in tokamaks. The largest signal contamination of ∼15% is seen in the core CX channels, where the true CX signal level is much lower than that in the edge channels. Similar values are obtained for Textor also. These results indicate that the contributions from wall reflections may be large enough to significantly distort the overall spectral features of CX data, warranting an analysis at different wavelengths.

Wall reflection modeling for charge exchange recombination spectroscopy (CXRS) measurements on Textor and ITER

Energy Technology Data Exchange (ETDEWEB)

Banerjee, Santanu; Vasu, P [Institute for Plasma Research, Bhat, Gandhinagar 382 428, Gujarat (India); Von Hellermann, M [FOM Institute for Plasma Physics, Rijnhuizen (Netherlands); Jaspers, R J E, E-mail: sbanerje@ipr.res.i [Applied Physics Department, Eindhoven University of Technology, Eindhoven (Netherlands)

2010-12-15

Contamination of optical signals by reflections from the tokamak vessel wall is a matter of great concern. For machines such as ITER and future reactors, where the vessel wall will be predominantly metallic, this is potentially a risk factor for quantitative optical emission spectroscopy. This is, in particular, the case when bremsstrahlung continuum radiation from the bulk plasma is used as a common reference light source for the cross-calibration of visible spectroscopy. In this paper the reflected contribution to the continuum level in Textor and ITER has been estimated for the detection channels meant for charge exchange recombination spectroscopy (CXRS). A model assuming diffuse reflection has been developed for the bremsstrahlung which is a much extended source. Based on this model, it is shown that in the case of ITER upper port 3, a wall with a moderate reflectivity of 20% leads to the wall reflected fraction being as high as 55-60% of the weak signals in the edge channels. In contrast, a complete bidirectional reflectance distribution function (BRDF) based model has been developed in order to estimate the reflections from more localized sources like the charge exchange (CX) emission from a neutral beam in tokamaks. The largest signal contamination of {approx}15% is seen in the core CX channels, where the true CX signal level is much lower than that in the edge channels. Similar values are obtained for Textor also. These results indicate that the contributions from wall reflections may be large enough to significantly distort the overall spectral features of CX data, warranting an analysis at different wavelengths.

Ideology, motivated reasoning, and cognitive reflection

Directory of Open Access Journals (Sweden)

Dan M. Kahan

2013-07-01

Full Text Available Decision scientists have identified various plausible sources of ideological polarization over climate change, gun violence, national security, and like issues that turn on empirical evidence. This paper describes a study of three of them: the predominance of heuristic-driven information processing by members of the public; ideologically motivated reasoning; and the cognitive-style correlates of political conservativism. The study generated both observational and experimental data inconsistent with the hypothesis that political conservatism is distinctively associated with either unreflective thinking or motivated reasoning. Conservatives did no better or worse than liberals on the Cognitive Reflection Test (Frederick, 2005, an objective measure of information-processing dispositions associated with cognitive biases. In addition, the study found that ideologically motivated reasoning is not a consequence of over-reliance on heuristic or intuitive forms of reasoning generally. On the contrary, subjects who scored highest in cognitive reflection were the most likely to display ideologically motivated cognition. These findings corroborated an alternative hypothesis, which identifies ideologically motivated cognition as a form of information processing that promotes individuals' interests in forming and maintaining beliefs that signify their loyalty to important affinity groups. The paper discusses the practical significance of these findings, including the need to develop science communication strategies that shield policy-relevant facts from the influences that turn them into divisive symbols of political identity.

Insight in Schizophrenia: Involvement of Self-Reflection Networks?

Science.gov (United States)

de Vos, Annerieke E.

2013-01-01

Background: Impaired insight is a common feature in psychosis and an important predictor of variables such as functional outcome, prognosis, and treatment adherence. A cognitive process that may underlie insight in psychosis is self-reflection, or the conscious evaluation of one’s traits and characteristics. The current study aims to investigate the neural correlates of self-reflective processing and its relationship with insight in schizophrenia. Methods: Forty-seven schizophrenia patients and 21 healthy controls performed a self-reflection task in a functional magnetic resonance imaging (fMRI) scanner. The tasks comprised a self-reflection, close other-reflection, and a semantic (baseline) condition. Insight scores were obtained with the Schedule of Assessment of Insight Expanded. In addition, cognitive insight scores were obtained (Beck Cognitive Insight Scale [BCIS]). Results: Schizophrenia patients demonstrated less activation in the posterior cingulate cortex in the self- and other-reflection conditions and less activation in the precuneus in the other-reflection condition compared with healthy controls. Better insight was associated with greater response in the inferior frontal gyrus, anterior insula, and inferior parietal lobule during self-reflection. In addition, better cognitive insight was associated with higher activation in ventromedial prefrontal cortex during self-reflection. Conclusion: In the current study, evidence for a relationship between self-reflection and insight in patients with schizophrenia was found in brain areas related to self-reflection, self/other distinction and source attribution. The findings support the rationale for a treatment that is currently under evaluation, which attempts to increase insight by enhancing self-reflection. PMID:23104865

The Reflective Learning Continuum: Reflecting on Reflection

Science.gov (United States)

Peltier, James W.; Hay, Amanda; Drago, William

2005-01-01

The importance of reflection to marketing educators is increasingly recognized. However, there is a lack of empirical research that considers reflection within the context of both the marketing and general business education literature. This article describes the use of an instrument that can be used to measure four identified levels of a…

Dry etching technologies for reflective multilayer

Science.gov (United States)

Iino, Yoshinori; Karyu, Makoto; Ita, Hirotsugu; Kase, Yoshihisa; Yoshimori, Tomoaki; Muto, Makoto; Nonaka, Mikio; Iwami, Munenori

2012-11-01

We have developed a highly integrated methodology for patterning Extreme Ultraviolet (EUV) mask, which has been highlighted for the lithography technique at the 14nm half-pitch generation and beyond. The EUV mask is characterized as a reflective-type mask which is completely different compared with conventional transparent-type of photo mask. And it requires not only patterning of absorber layer without damaging the underlying multi reflective layers (40 Si/Mo layers) but also etching multi reflective layers. In this case, the dry etch process has generally faced technical challenges such as the difficulties in CD control, etch damage to quartz substrate and low selectivity to the mask resist. Shibaura Mechatronics ARESTM mask etch system and its optimized etch process has already achieved the maximal etch performance at patterning two-layered absorber. And in this study, our process technologies of multi reflective layers will be evaluated by means of optimal combination of process gases and our optimized plasma produced by certain source power and bias power. When our ARES™ is used for multilayer etching, the user can choose to etch the absorber layer at the same time or etch only the multilayer.

Near infrared spectral imaging of explosives using a tunable laser source

Energy Technology Data Exchange (ETDEWEB)

Klunder, G L; Margalith, E; Nguyen, L K

2010-03-26

Diffuse reflectance near infrared hyperspectral imaging is an important analytical tool for a wide variety of industries, including agriculture consumer products, chemical and pharmaceutical development and production. Using this technique as a method for the standoff detection of explosive particles is presented and discussed. The detection of the particles is based on the diffuse reflectance of light from the particle in the near infrared wavelength range where CH, NH, OH vibrational overtones and combination bands are prominent. The imaging system is a NIR focal plane array camera with a tunable OPO/laser system as the illumination source. The OPO is programmed to scan over a wide spectral range in the NIR and the camera is synchronized to record the light reflected from the target for each wavelength. The spectral resolution of this system is significantly higher than that of hyperspectral systems that incorporate filters or dispersive elements. The data acquisition is very fast and the entire hyperspectral cube can be collected in seconds. A comparison of data collected with the OPO system to data obtained with a broadband light source with LCTF filters is presented.

A model for calculating specular and diffuse reflections in outdoor sound propagation

NARCIS (Netherlands)

Salomons, E.M.

2006-01-01

In many practical outdoor situations, the direct sound path between a noise source and a receiver is screened by an obstacle. In these situations indirect sound paths become important, in particular reflections of sound waves. Reflections may occur at objects such as a vertical wall, but also at the

A functional equation for the specular reflection of rays.

Science.gov (United States)

Le Bot, A

2002-10-01

This paper aims to generalize the "radiosity method" when applied to specular reflection. Within the field of thermics, the radiosity method is also called the "standard procedure." The integral equation for incident energy, which is usually derived for diffuse reflection, is replaced by a more appropriate functional equation. The latter is used to solve some specific problems and it is shown that all the classical features of specular reflection, for example, the existence of image sources, are embodied within this equation. This equation can be solved with the ray-tracing technique, despite the implemented mathematics being quite different. Several interesting features of the energy field are presented.

Retrieval of reflections from seismic background?noise measurements

NARCIS (Netherlands)

Draganov, D.S.; Wapenaar, K.; Mulder, W.; Singer, J.; Verdel, A.

2007-01-01

The retrieval of the earth's reflection response from cross?correlations of seismic noise recordings can provide valuable information, which may otherwise not be available due to limited spatial distribution of seismic sources. We cross?correlated ten hours of seismic background?noise data acquired

Specialized Color Targets for Spectral Reflectance Reconstruction of Magnified Images

Science.gov (United States)

Kruschwitz, Jennifer D. T.

Digital images are used almost exclusively instead of film to capture visual information across many scientific fields. The colorimetric color representation within these digital images can be relayed from the digital counts produced by the camera with the use of a known color target. In image capture of magnified images, there is currently no reliable color target that can be used at multiple magnifications and give the user a solid understanding of the color ground truth within those images. The first part of this dissertation included the design, fabrication, and testing of a color target produced with optical interference coated microlenses for use in an off-axis illumination, compound microscope. An ideal target was designed to increase the color gamut for colorimetric imaging and provide the necessary "Block Dye" spectral reflectance profiles across the visible spectrum to reduce the number of color patches necessary for multiple filter imaging systems that rely on statistical models for spectral reflectance reconstruction. There are other scientific disciplines that can benefit from a specialized color target to determine the color ground truth in their magnified images and perform spectral estimation. Not every discipline has the luxury of having a multi-filter imaging system. The second part of this dissertation developed two unique ways of using an interference coated color mirror target: one that relies on multiple light-source angles, and one that leverages a dynamic color change with time. The source multi-angle technique would be used for the microelectronic discipline where the reconstructed spectral reflectance would be used to determine a dielectric film thickness on a silicon substrate, and the time varying technique would be used for a biomedical example to determine the thickness of human tear film.

Single view reflectance capture using multiplexed scattering and time-of-flight imaging

OpenAIRE

Zhao, Shuang; Velten, Andreas; Raskar, Ramesh; Bala, Kavita; Naik, Nikhil Deepak

2011-01-01

This paper introduces the concept of time-of-flight reflectance estimation, and demonstrates a new technique that allows a camera to rapidly acquire reflectance properties of objects from a single view-point, over relatively long distances and without encircling equipment. We measure material properties by indirectly illuminating an object by a laser source, and observing its reflected light indirectly using a time-of-flight camera. The configuration collectively acquires dense angular, but l...

Ground magnetic studies along a regional seismic-reflection profile across Bare Mountain, Crater Flat and Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Langenheim, V.E.; Ponce, D.A.

1995-01-01

Ground magnetic data were collected along a 26-km-long regional seismic-reflection profile in southwest Nevada that starts in the Amargosa Desert, crosses Bare Mountain, Crater Flat and Yucca Mountain, and ends in Midway Valley. Parallel ground magnetic profiles were also collected about 100 m to either side of the western half of the seismic-reflection line. The magnetic data indicate that the eastern half of Crater Flat is characterized by closely-spaced faulting (1--2 km) in contrast to the western half of Crater Flat. Modeling of the data indicates that the Topopah Spring Tuff is offset about 250 m on the Solitario Canyon fault and about 50 m on the Ghost Dance fault. These estimates of fault offset are consistent with seismic-reflection data and geologic mapping. A broad magnetic high of about 500--600 nT is centered over Crater Flat. Modeling of the magnetic data indicates that the source of this high is not thickening and doming of the Bullfrog Tuff, but more likely lies below the Bullfrog Tuff. Possible source lithologies for this magnetic high include altered argillite of the Eleana Formation, Cretaceous or Tertiary intrusions, and mafic sills

Source term estimation during incident response to severe nuclear power plant accidents. Draft

Energy Technology Data Exchange (ETDEWEB)

McKenna, T J; Giitter, J

1987-07-01

The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. The goal is to present a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. (author)

Source term estimation during incident response to severe nuclear power plant accidents. Draft

International Nuclear Information System (INIS)

McKenna, T.J.; Giitter, J.

1987-01-01

The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. The goal is to present a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. (author)

Source term estimation during incident response to severe nuclear power plant accidents

International Nuclear Information System (INIS)

McKenna, T.J.; Glitter, J.G.

1988-10-01

This document presents a method of source term estimation that reflects the current understanding of source term behavior and that can be used during an event. The various methods of estimating radionuclide release to the environment (source terms) as a result of an accident at a nuclear power reactor are discussed. The major factors affecting potential radionuclide releases off site (source terms) as a result of nuclear power plant accidents are described. The quantification of these factors based on plant instrumentation also is discussed. A range of accident conditions from those within the design basis to the most severe accidents possible are included in the text. A method of gross estimation of accident source terms and their consequences off site is presented. 39 refs., 48 figs., 19 tabs

State-dependent cellular activity patterns of the cat paraventricular hypothalamus measured by reflectance imaging

DEFF Research Database (Denmark)

Kristensen, Morten Pilgaard; Rector, D M; Poe, G R

1996-01-01

Activity within the cat paraventricular hypothalamus (PVH) during sleep and waking states was measured by quantifying intrinsic tissue reflectivity. A fiber optic probe consisting of a 1.0 mm coherent image conduit, surrounded by plastic fibers which conducted 660 nm source light, was attached...... to a charge-coupled device camera, and positioned over the PVH in five cats. Electrodes for assessing state variables, including electroencephalographic activity, eye movement, and somatic muscle tone were also placed. After surgical recovery, reflected light intensity was measured continuously at 2.5 Hz...... changes with behavioral state in a regionally specific manner, and that overall activity increases during quiet sleep, and is even more enhanced in active sleep. PVH activation could be expected to stimulate pituitary release of adrenocorticotropic hormone (ACTH) and affect input to autonomic regulatory...

Potential Sources of Polarized Light from a Plant Canopy

Science.gov (United States)

Vanderbilt, Vern; Daughtry, Craig; Dahlgren, Robert

2016-01-01

Field measurements have demonstrated that sunlight polarized during a first surface reflection by shiny leaves dominates the optical polarization of the light reflected by shiny-leafed plant canopies having approximately spherical leaf angle probability density functions ("Leaf Angle Distributions" - LAD). Yet for other canopies - specifically those without shiny leaves and/or spherical LADs - potential sources of optically polarized light may not always be obvious. Here we identify possible sources of polarized light within those other canopies and speculate on the ecologically important information polarization measurements of those sources might contain.

Reflectance variability of surface coatings reveals characteristic eigenvalue spectra

Science.gov (United States)

Medina, José M.; Díaz, José A.; Barros, Rui

2012-10-01

We have examined the trial-to-trial variability of the reflectance spectra of surface coatings containing effect pigments. Principal component analysis of reflectances was done at each detection angle separately. A method for classification of principal components is applied based on the eigenvalue spectra. It was found that the eigenvalue spectra follow characteristic power laws and depend on the detection angle. Three different subsets of principal components were examined to separate the relevant spectral features related to the pigments from other noise sources. Reconstruction of the reflectance spectra by taking only the first subset indicated that reflectance variability was higher at near-specular reflection, suggesting a correlation with the trial-to-trial deposition of effect pigments. Reconstruction by using the second subset indicates that variability was higher at short wavelengths. Finally, reconstruction by using only the third subset indicates that reflectance variability was not totally random as a function of the wavelength. The methods employed can be useful in the evaluation of color variability in industrial paint application processes.

Free software, Open source software, licenses. A short presentation including a procedure for research software and data dissemination

OpenAIRE

Gomez-Diaz , Teresa

2014-01-01

4 pages. Spanish version: Software libre, software de código abierto, licencias. Donde se propone un procedimiento de distribución de software y datos de investigación; The main goal of this document is to help the research community to understand the basic concepts of software distribution: Free software, Open source software, licenses. This document also includes a procedure for research software and data dissemination.

Spectral implementation of full waveform inversion based on reflections

KAUST Repository

Wu, Zedong

2014-01-01

Using the reflection imaging process as a source to model reflections for full waveform inversion (FWI), referred to as reflection FWI (RFWI), allows us to update the background component of the model, and avoid using the relatively costly migration velocity analysis (MVA), which usually relies on extended images. However, RFWI requires a good image to represent the current reflectivity, as well as, some effort to obtain good smooth gradients. We develop a spectral implementation of RFWI where the wavefield extrapolations and gradient evaluation are performed in the wavenumber domain, obtaining clean dispersion free and fast extrapolations. The gradient, in this case, yields three terms, two of which provide us with each side of the rabbit ear kernel, and the third, often ignored, provides a normalization of the reflectivity within the kernel, which can be used to obtain a reflectivity free background update. Since the image is imperfect (it is an adjoint, not an inverse), an optimization process for the third term scaling is implemented to achieve the smoothest gradient update. A rare application of RFWI on the reflectivity infested Marmousi model shows some of the potential of the approach.

High-resolution seismic reflection surveying with a land streamer

Science.gov (United States)

Cengiz Tapırdamaz, Mustafa; Cankurtaranlar, Ali; Ergintav, Semih; Kurt, Levent

2013-04-01

In this study, newly designed seismic reflection data acquisition array (land streamer) is utilized to image the shallow subsurface. Our acquisition system consist of 24 geophones screwed on iron plates with 2 m spacing, moving on the surface of the earth which are connected with fire hose. Completely original, 4.5 Kg weight iron plates provides satisfactory coupling. This land-streamer system enables rapid and cost effective acquisition of seismic reflection data due to its operational facilities. First test studies were performed using various seismic sources such as a mini-vibro truck, buffalo-gun and hammer. The final fieldwork was performed on a landslide area which was studied before. Data acquisition was carried out on the line that was previously measured by the seismic survey using 5 m geophone and shot spacing. This line was chosen in order to re-image known reflection patterns obtained from the previous field study. Taking penetration depth into consideration, a six-cartridge buffalo-gun was selected as a seismic source to achieve high vertical resolution. Each shot-point drilled 50 cm for gunshots to obtain high resolution source signature. In order to avoid surface waves, the offset distance between the source and the first channel was chosen to be 50 m and the shot spacing was 2 m. These acquisition parameters provided 12 folds at each CDP points. Spatial sampling interval was 1 m at the surface. The processing steps included standard stages such as gain recovery, editing, frequency filtering, CDP sorting, NMO correction, static correction and stacking. Furthermore, surface consistent residual static corrections were applied recursively to improve image quality. 2D F-K filter application was performed to suppress air and surface waves at relatively deep part of the seismic section. Results show that, this newly designed, high-resolution land seismic data acquisition equipment (land-streamer) can be successfully used to image subsurface. Likewise

Studies of dust grain properties in infrared reflection nebulae.

Science.gov (United States)

Pendleton, Y J; Tielens, A G; Werner, M W

1990-01-20

We have developed a model for reflection nebulae around luminous infrared sources embedded in dense dust clouds. The aim of this study is to determine the sizes of the scattering grains. In our analysis, we have adopted an MRN-like power-law size distribution (Mathis, Rumpl, and Nordsieck) of graphite and silicate grains, but other current dust models would give results which were substantially the same. In the optically thin limit, the intensity of the scattered light is proportional to the dust column density, while in the optically thick limit, it reflects the grain albedo. The results show that the shape of the infrared spectrum is the result of a combination of the scattering properties of the dust, the spectrum of the illuminating source, and foreground extinction, while geometry plays a minor role. Comparison of our model results with infrared observations of the reflection nebula surrounding OMC-2/IRS 1 shows that either a grain size distribution like that found in the diffuse interstellar medium, or one consisting of larger grains, can explain the observed shape of the spectrum. However, the absolute intensity level of the scattered light, as well as the observed polarization, requires large grains (approximately 5000 angstroms). By adding water ice mantles to the silicate and graphite cores, we have modeled the 3.08 micrometers ice band feature, which has been observed in the spectra of several infrared reflection nebulae. We show that this ice band arises naturally in optically thick reflection nebulae containing ice-coated grains. We show that the shape of the ice band is diagnostic of the presence of large grains, as previously suggested by Knacke and McCorkle. Comparison with observations of the BN/KL reflection nebula in the OMC-1 cloud shows that large ice grains (approximately 5000 angstroms) contribute substantially to the scattered light.

Reflection, Interrogatory, Provocation

International Nuclear Information System (INIS)

Carnes, W.E.

2016-01-01

This invited paper advances a framing context for considering next steps in HOF and organizational culture in light of the presentations and discussions that occur during the conference. Many of the contributions during the conference will represent results of scholarly research, structured investigations, or formal organizational improvement efforts. This contribution is intended as informal reflection by a 40-year nuclear veteran on themes from other presentations considering questions such as: ''Where do we think we are?, Are we better off as an industry based on what we have done?, Where do we think we need to go?, What do we think we need to do?, and, Why do we think these things?'' Our coming together on this occasion marks 30 years since the publication of INSAG-l. As we reflect on the past, perhaps it is time to pose a series of questions. Are we sustainers of a mature technology that is in some places declining and being replaced by other energy sources? If we consider nuclear a mature technology, should we focus most on operational excellence with renewed attention to managing the unexpected? Or, is innovation still a vital part of our industry?

Use of gaseous tritium light sources (Beta lights) with respect to nocturnal illumination

International Nuclear Information System (INIS)

Solomon, D.E.

1988-01-01

A number/letter plate for use in, for example darkened buildings has spaced apart gaseous tritium light sources (beta lights) arranged centrally along the indicia on a reflective background sealed in clear translucent plastics. Uses include house numbers, name plates, telephone numbers, notices, product advertisements, vehicle registration plates and names or trade marks on products. (author)

Challenging Narcissus, or Reflecting on Reflecting.

Science.gov (United States)

Achilles, C. M.

The concept of reflective practice and teaching people to be reflective practitioners is examined. The document begins with a look at professional knowledge according to three prominent professionals in the educational administration field: Schon, Schein, and Achilles. "Reflective" strategies that could be incorporated into courses and…

Selectively reflective transparent sheets

Science.gov (United States)

Waché, Rémi; Florescu, Marian; Sweeney, Stephen J.; Clowes, Steven K.

2015-08-01

We investigate the possibility to selectively reflect certain wavelengths while maintaining the optical properties on other spectral ranges. This is of particular interest for transparent materials, which for specific applications may require high reflectivity at pre-determined frequencies. Although there exist currently techniques such as coatings to produce selective reflection, this work focuses on new approaches for mass production of polyethylene sheets which incorporate either additives or surface patterning for selective reflection between 8 to 13 μ m. Typical additives used to produce a greenhouse effect in plastics include particles such as clays, silica or hydroxide materials. However, the absorption of thermal radiation is less efficient than the decrease of emissivity as it can be compared with the inclusion of Lambertian materials. Photonic band gap engineering by the periodic structuring of metamaterials is known in nature for producing the vivid bright colors in certain organisms via strong wavelength-selective reflection. Research to artificially engineer such structures has mainly focused on wavelengths in the visible and near infrared. However few studies to date have been carried out to investigate the properties of metastructures in the mid infrared range even though the patterning of microstructure is easier to achieve. We present preliminary results on the diffuse reflectivity using FDTD simulations and analyze the technical feasibility of these approaches.

Shallow reflection seismic soundings in bedrock at Lavia

International Nuclear Information System (INIS)

Okko, Olli

1988-03-01

The well-studied granitic block at Lavia was one of the test sites of a shallow seismic development project. A portable digital seismograph and high frequency geophones were rented fro the field period. A sledge hamme and a drop weight were tested as wave sources. The sounding was carried out on outcropped area in order to record high frequency reflections from known subhorizontal fracture zones as shallow as 30 m. Large amplitude surface waves hide most of the shallow reflections, recognizable only on few traces in the data. The data processing carried out did not reveal the geometry of these reflectors. Events arriving after the ground roll were analyzed in 2-folded CDP-sections. The continuous reflective horizons in them correspond to lithological changes and fracture zones located deeper than 200 m in the bedrock

Some preliminary design considerations for the ANS [Advanced Neutron Source] reactor cold source

International Nuclear Information System (INIS)

Henderson, D.L.

1988-01-01

Two areas concerned with the design of the Advanced Neutron Source (ANS) cold source have been investigated by simple one-dimensional calculations. The gain factors computed for a possible liquid nitrogen-15 cold source moderator are considerably below those computed for the much colder liquid deuterium moderator, as is reasonable considering the difference in moderator temperature. Nevertheless, nitrogen-15 does represent a viable option should safety related issues prohibit the use of deuterium as a moderating material. The slab geometry calculations have indicated that reflection of neutrons may be the dominant moderating mechanism and should be a consideration in the design of the cold source. 9 refs., 2 figs

EEGLAB: an open source toolbox for analysis of single-trial EEG dynamics including independent component analysis.

Science.gov (United States)

Delorme, Arnaud; Makeig, Scott

2004-03-15

We have developed a toolbox and graphic user interface, EEGLAB, running under the crossplatform MATLAB environment (The Mathworks, Inc.) for processing collections of single-trial and/or averaged EEG data of any number of channels. Available functions include EEG data, channel and event information importing, data visualization (scrolling, scalp map and dipole model plotting, plus multi-trial ERP-image plots), preprocessing (including artifact rejection, filtering, epoch selection, and averaging), independent component analysis (ICA) and time/frequency decompositions including channel and component cross-coherence supported by bootstrap statistical methods based on data resampling. EEGLAB functions are organized into three layers. Top-layer functions allow users to interact with the data through the graphic interface without needing to use MATLAB syntax. Menu options allow users to tune the behavior of EEGLAB to available memory. Middle-layer functions allow users to customize data processing using command history and interactive 'pop' functions. Experienced MATLAB users can use EEGLAB data structures and stand-alone signal processing functions to write custom and/or batch analysis scripts. Extensive function help and tutorial information are included. A 'plug-in' facility allows easy incorporation of new EEG modules into the main menu. EEGLAB is freely available (http://www.sccn.ucsd.edu/eeglab/) under the GNU public license for noncommercial use and open source development, together with sample data, user tutorial and extensive documentation.

An Optical Fiber Read Out Method for a Reflective Microcantilever Biosensor

Directory of Open Access Journals (Sweden)

Feng Wen

2013-03-01

Full Text Available An effective optical read out approach based on fiber reflective is presented to detect bends of a biomaterial microcantilever. The microcantilever was fabricated on single crystalline SOI wafer using a series of side definitions and backside wet/dry etchings. A Cr/Au layer with 30 nm Cr and 50 nm Au layer was deposited for the immobilized of bimolecular on the cantilever surface and for reflecting the light back into the fiber, the different light intensities means different bimolecular concentrations. The noncoherent light source is a super luminescent LED. Gradient index lens as a collimator and 50:50 optical coupler and signal modefiber was used to transmit light. Two PINFETs were used to convert the reflecting the light intensities and the light sources into electronic signals, two ADCs convert the signal into digital signals, a MPU was used to eliminate the fluctuation of the light source error. The method can has got high sensitivity is 6507.59 mV/um. Though the experiment, the cantilever biosensor can detect glucose, measurement results clearly demonstrate that the output voltage induced by the microcantilevers bending is proportional to the glucose concentrations and the sensitivity is up to 0.1V/mM, which is enough for glucose real-time trace detection.

Variable blurred reflection in the narrow-line Seyfert 1 galaxy Mrk 493

Science.gov (United States)

Bonson, K.; Gallo, L. C.; Wilkins, D. R.; Fabian, A. C.

2018-04-01

We examine a 200 ks XMM-Newton observation of the narrow-line Seyfert 1 galaxy Mrk 493. The active galaxy was half as bright as in a previous 2003 snapshot observation and the current lower flux enables a study of the putative reflection component in detail. We determine the characteristics of the 2015 X-ray continuum by first analyzing the short-term variability using model-independent techniques. We then continue with a time-resolve analysis including spectral fitting and modelling the fractional variability. We determine that the variability arises from changes in the amount of primary flux striking the accretion disk, which induces changes in the ionization parameter and flux of the blurred reflection component. The observations seem consistent with the picture that the primary source is of roughly constant brightness and that variations arise from changes in the degree of light bending happening in the vicinity of the supermassive black hole.

Shack-Hartmann reflective micro profilometer

Science.gov (United States)

Gong, Hai; Soloviev, Oleg; Verhaegen, Michel; Vdovin, Gleb

2018-01-01

We present a quantitative phase imaging microscope based on a Shack-Hartmann sensor, that directly reconstructs the optical path difference (OPD) in reflective mode. Comparing with the holographic or interferometric methods, the SH technique needs no reference beam in the setup, which simplifies the system. With a preregistered reference, the OPD image can be reconstructed from a single shot. Also, the method has a rather relaxed requirement on the illumination coherence, thus a cheap light source such as a LED is feasible in the setup. In our previous research, we have successfully verified that a conventional transmissive microscope can be transformed into an optical path difference microscope by using a Shack-Hartmann wavefront sensor under incoherent illumination. The key condition is that the numerical aperture of illumination should be smaller than the numerical aperture of imaging lens. This approach is also applicable to characterization of reflective and slightly scattering surfaces.

Modeling the effect of reflection from metallic walls on spectroscopic measurements

International Nuclear Information System (INIS)

Zastrow, K.-D.; Keatings, S. R.; O'Mullane, M. G.; Marot, L.; Temmerman, G. de

2008-01-01

A modification of JET is presently being prepared to bring operational experience with ITER-like first wall (Be) and divertor (W) materials, geometry and plasma parameters. Reflectivity measurements of JET sample tiles have been performed and the data are used within a simplified model of the JET and ITER vessels to predict additional contributions to quantitative spectroscopic measurements. The most general method to characterize reflectivity is the bidirectional reflection distribution function (BRDF). For extended sources however, such as bremsstrahlung and edge emission of fuel and intrinsic impurities, the results obtained in the modeling are almost as accurate if the total reflectivity with ideal Lambertian angular dependence is used. This is in contrast to the experience in other communities, such as optical design, lighting design, or rendering who deal mostly with pointlike light sources. This result is so far based on a very limited set of measurements and will be reassessed when more detailed BRDF measurements of JET tiles have been made. If it is true it offers the possibility of in situ monitoring of the reflectivity of selected parts of the wall during exposure to plasma operation, while remeasurement of the BRDF is performed during interventions. For a closed vessel structure such as ITER, it is important to consider multiple reflections. This makes it more important to represent the whole of the vessel reasonably accurately in the model, which on the other hand is easier to achieve than for the more complex internal structure of JET. In both cases the dominant contribution is from the first reflection, and a detailed model of the areas intersected by lines of sight of diagnostic interest is required.

Extracellular vesicle RNAs reflect placenta dysfunction and are a biomarker source for preterm labour.

Science.gov (United States)

Fallen, Shannon; Baxter, David; Wu, Xiaogang; Kim, Taek-Kyun; Shynlova, Oksana; Lee, Min Young; Scherler, Kelsey; Lye, Stephen; Hood, Leroy; Wang, Kai

2018-05-01

Preterm birth (PTB) can lead to lifelong complications and challenges. Identifying and monitoring molecular signals in easily accessible biological samples that can diagnose or predict the risk of preterm labour (PTL) in pregnant women will reduce or prevent PTBs. A number of studies identified putative biomarkers for PTL including protein, miRNA and hormones from various body fluids. However, biomarkers identified from these studies usually lack consistency and reproducibility. Extracellular vesicles (EVs) in circulation have gained significant interest in recent years as these vesicles may be involved in cell-cell communication. We have used an improved small RNA library construction protocol and a newly developed size exclusion chromatography (SEC)-based EV purification method to gain a comprehensive view of circulating RNA in plasma and its distribution by analysing RNAs in whole plasma and EV-associated and EV-depleted plasma. We identified a number of miRNAs in EVs that can be used as biomarkers for PTL, and these miRNAs may reflect the pathological changes of the placenta during the development of PTL. To our knowledge, this is the first study to report a comprehensive picture of circulating RNA, including RNA in whole plasma, EV and EV-depleted plasma, in PTL and reveal the usefulness of EV-associated RNAs in disease diagnosis. © 2018 The Authors. Journal of Cellular and Molecular Medicine published by John Wiley & Sons Ltd and Foundation for Cellular and Molecular Medicine.

Investigating Bidirectional Reflectance in the Los Angeles Megacity Using CLARS Multiangle and Hyperspectral Measurements

Science.gov (United States)

Zeng, Z. C.; Natraj, V.; Pongetti, T.; Shia, R. L.; Sander, S. P.; Yung, Y. L.

2017-12-01

The surface reflectance is a key ingredient in the remote sensing of surface and atmospheric properties from space. The determination of atmospheric composition, including greenhouse gas (GHG) and aerosol concentrations, from reflected sunlight requires accurate knowledge of the contribution from the underlying surface. Over megacity areas, such as the Los Angeles (LA) basin, which are major sources of GHGs and anthropogenic aerosols, the quantification of surface reflectance is challenging due to the associated complex land use types. In this study, we investigate the bidirectional reflectance in the Los Angeles megacity area using multiangle and hyperspectral radiance measurements from the California Laboratory for Atmospheric Remote Sensing (CLARS). The CLARS facility is located near the top of Mt. Wilson, at an altitude of 1670 m a.s.l., overlooking the LA megacity area with an FTS operating since 2011 to continuously monitor the GHGs and near-surface aerosols in the basin. The CLARS-FTS offers continuous high-resolution spectral measurements in the visible, near infrared and shortwave infrared spectral regions. The CLARS measurements mimic the off-nadir viewing of a low-Earth orbiting instrument, such as GOSAT and OCO-2, but with daily viewing capability. Eight surface targets with different land use types, including urban parks, industrial and residential areas, are selected in this study. The surface reflectance for specific solar incident and viewing angles is calculated by dividing, for non-absorbing spectral channels on clear days (such that gas and aerosol extinction can be ignored), the observed radiance reflected from surface targets by the observed irradiance. The non-linear Rahman-Pinty-Verstraete (RPV) model is used to model the Bidirectional Reflectance Distribution Function (BRDF) by fitting the multiangle and hyperspectral measurements. By evaluating the retrieved RPV parameters, we find that the RPV model provides a good representation of the

Measurement and models of bent KAP(001) crystal integrated reflectivity and resolution (invited)

Energy Technology Data Exchange (ETDEWEB)

Loisel, G. P., E-mail: gploise@sandia.gov; Wu, M.; Lake, P.; Dunham, G. S.; Bailey, J. E.; Rochau, G. A. [Sandia National Laboratories, Albuquerque, New Mexico 87185 (United States); Stolte, W. [National Security Technologies, LLC, Livermore, California 94551 (United States); Kruschwitz, C. [National Security Technologies, LLC, Los Alamos, New Mexico 87544 (United States)

2016-11-15

The Advanced Light Source beamline-9.3.1 x-rays are used to calibrate the rocking curve of bent potassium acid phthalate (KAP) crystals in the 2.3-4.5 keV photon-energy range. Crystals are bent on a cylindrically convex substrate with a radius of curvature ranging from 2 to 9 in. and also including the flat case to observe the effect of bending on the KAP spectrometric properties. As the bending radius increases, the crystal reflectivity converges to the mosaic crystal response. The X-ray Oriented Programs (XOP) multi-lamellar model of bent crystals is used to model the rocking curve of these crystals and the calibration data confirm that a single model is adequate to reproduce simultaneously all measured integrated reflectivities and rocking-curve FWHM for multiple radii of curvature in both 1st and 2nd order of diffraction.

Room-temperature near-field reflection spectrocopy of semiconductor nanostructures

DEFF Research Database (Denmark)

Langbein, Wolfgang; Hvam, Jørn Märcher; Madsen, Steen

1999-01-01

We investigate the properties of near-field reflection spectroscopy in different polarization and detection modes using uncoated fiber probes. The results show, that cross-polarized detection suppresses to a large extent far-field contributions. Using the fiber dithering as a modulation source fo...

High resolution reflection seismic mapping of shallow coal seams

CSIR Research Space (South Africa)

Mngadi, SB

2013-10-01

Full Text Available the extent of the mine workings. Two 94 m profiles (tied to boreholes) were surveyed using a sledgehammer source. Processing was optimized to image the shallow reflections. The refraction seismic models and stacked time sections were compared and integrated...

Information content in reflected global navigation satellite system signals

DEFF Research Database (Denmark)

Høeg, Per; Carlstrom, Anders

2011-01-01

The direct signals from satellites in global satellite navigation satellites systems (GNSS) as, GPS, GLONASS and GALILEO, constitute the primary source for positioning, navigation and timing from space. But also the reflected GNSS signals contain an important information content of signal travel...

Reconstruction of Sound Source Pressures in an Enclosure Using the Phased Beam Tracing Method

DEFF Research Database (Denmark)

Jeong, Cheol-Ho; Ih, Jeong-Guon

2009-01-01

. First, surfaces of an extended source are divided into reasonably small segments. From each source segment, one beam is projected into the field and all emitted beams are traced. Radiated beams from the source reach array sensors after traveling various paths including the wall reflections. Collecting...... all the pressure histories at the field points, source-observer relations can be constructed in a matrix-vector form for each frequency. By multiplying the measured field data with the pseudo-inverse of the calculated transfer function, one obtains the distribution of source pressure. An omni......-directional sphere and a cubic source in a rectangular enclosure were taken as examples in the simulation tests. A reconstruction error was investigated by Monte Carlo simulation in terms of field point locations. When the source information was reconstructed by the present method, it was shown that the sound power...

Acoustic reflection log in transversely isotropic formations

Science.gov (United States)

Ronquillo Jarillo, G.; Markova, I.; Markov, M.

2018-01-01

We have calculated the waveforms of sonic reflection logging for a fluid-filled borehole located in a transversely isotropic rock. Calculations have been performed for an acoustic impulse source with the characteristic frequency of tens of kilohertz that is considerably less than the frequencies of acoustic borehole imaging tools. It is assumed that the borehole axis coincides with the axis of symmetry of the transversely isotropic rock. It was shown that the reflected wave was excited most efficiently at resonant frequencies. These frequencies are close to the frequencies of oscillations of a fluid column located in an absolutely rigid hollow cylinder. We have shown that the acoustic reverberation is controlled by the acoustic impedance of the rock Z = Vphρs for fixed parameters of the borehole fluid, where Vph is the velocity of horizontally propagating P-wave; ρs is the rock density. The methods of waveform processing to determine the parameters characterizing the reflected wave have been discussed.

Personal Professional Reflection as Interdisciplinary Problem

Directory of Open Access Journals (Sweden)

Rezvan Oksana

2013-08-01

Full Text Available Consideration of professional reflection as interdisciplinary problem is the necessary condition of quality analysis for personal professional becoming. Personal becoming in a profession is related to forming the necessary professional skills of a person, behaviour stereotypes which is the area of pedagogics. Reflection processes are inalienable part of self-knowledge of a person which result must lead to his self-perfection (including professional one and studying within the psychology increasingly. Thus the aim of the article is to ground the determination of professional reflection as an interdisciplinary problem in pedagogics and psychology.

Validating the Persian Version of Reflective Thinking Questionnaire and Probing Iranian University Students' Reflective Thinking and Academic Achievement

Directory of Open Access Journals (Sweden)

Afsaneh Ghanizadeh

2017-07-01

Full Text Available Scholars in higher education deem reflective thinking as integral to the development of professional disciplinary practices. One of the major issues in studying reflective thinking pivots around its conceptualization and assessment. Over the years, researchers have used several methods and scales to measure reflective thinking. One of the most widely known scales of reflective thinking was constructed and validated by Kember et al. (2000. It is entitled 'Reflective Thinking Questionnaire (RTQ' and includes 16 items measuring four types of reflective thinking: understanding (UND; reflection (REF; critical reflection (CREF; habitual action (HA. The present study aimed at validating the Persian version of RTQ among one hundred ninety six English as a foreign language (EFL university students. It then scrutinized the role of reflective thinking in academic achievements measured by grade point average (GPA. The association of learners' reflective thinking style with their educational level and gender was also estimated. To conduct the research, the scale was first translated into Persian and its validity (computed via confirmatory factor analysis, convergent, and divergent validity estimates and reliability (computed via Cronbach's alpha were substantiated. It was indicated that among the comprising factors of reflective thinking, UND received the highest mean followed by REF and CREF

Supporting Fieldwork Learning by Visual Documentation and Reflection

DEFF Research Database (Denmark)

Saltofte, Margit

2017-01-01

Photos can be used as a supplements to written fieldnotes and as a sources for mediating reflection during fieldwork and analysis. As part of a field diary, photos can support the recall of experiences and a reflective distance to the events. Photography, as visual representation, can also lead...... to reflection on learning and knowledge production in the process of learning how to conduct fieldwork. Pictures can open the way for abstractions and hidden knowledge, which might otherwise be difficult to formulate in words. However, writing and written field notes cannot be fully replaced by photos...... the role played by photos in their learning process. For students, photography is an everyday documentation form that can support their memory of field experience and serve as a vehicle for the analysis of data. The article discusses how photos and visual representations support fieldwork learning...

Improving Inquiry Teaching through Reflection on Practice

Science.gov (United States)

Lotter, Christine R.; Miller, Cory

2017-08-01

In this paper, we explore middle school science teachers' learning of inquiry-based instructional strategies through reflection on practice teaching sessions during a summer enrichment program with middle level students. The reflection sessions were part of a larger year-long inquiry professional development program in which teachers learned science content and inquiry pedagogy. The program included a 2-week summer institute in which teachers participated in science content sessions, practice teaching to middle level students, and small group-facilitated reflection sessions on their teaching. For this study, data collection focused on teachers' recorded dialogue during the facilitator - run reflection sessions, the teachers' daily written reflections, a final written reflection, and a written reflection on a videotaped teaching session. We investigated the teachers' reflection levels and the themes teachers focused on during their reflection sessions. Teachers were found to reflect at various reflection levels, from simple description to a more sophisticated focus on how to improve student learning. Recurrent themes point to the importance of providing situated learning environments, such as the practice teaching with immediate reflection for teachers to have time to practice new instructional strategies and gain insight from peers and science educators on how to handle student learning issues.

Vertical seismic profiling and integration with reflection seismic studies at Laxemar, 2000

International Nuclear Information System (INIS)

Juhlin, C.; Bergman, B.; Cosma, C.; Keskinen, J.; Enescu, N.

2002-02-01

Vertical seismic profile (VSP) data were acquired in October 2000 in the 1700 m deep KLX02 borehole, near Laxemar in southeastern Sweden. The objectives of the VSP were to image reflectors in the borehole for correlation with surface seismic and borehole data, study the signal penetration of explosive versus mechanical sources and determine the seismic velocity as a function of depth. Five principal source points were used, one located close to the KLX02 wellhead and 4 others that were offset by about 200 m to 400 m. An explosive source was only used at the wellhead and consisted of 15 grams of dynamite in 90 cm deep shot holes in bedrock. A swept impact seismic source (SIST) was also used at the wellhead, as well as at the other four offset source points. The primary SIST source consisted of a computer controlled mechanical hammer mounted on a tractor. By activating the hammer over a 15 second sweep length, the total energy transferred to the ground is on the same order as that produced by the dynamite. The recorded data are then processed to generate seismic records that are equivalent to a single impact source. A smaller hand held SIST source was also tested at the wellhead. Tests of both the tractor mounted source and dynamite were made at a location offset somewhat from the wellhead at a site containing loose sediments at the surface. Full waveform sonic, resistivity and gamma logs were also acquired in conjunction the VSP survey. A comparison between the explosive and large SIST source shows that comparable energy levels are produced by the two methods. The SIST source appears to be more stable in terms of the energy level, although the frequency content of data are somewhat lower. However, its most significant advantage is the low cost of preparation of the source points and the speed of the acquisition. Numerous reflections are observed on the VSP, as is the case on the surface seismic, implying a complex structure in the vicinity of the KLX02 borehole

Vertical seismic profiling and integration with reflection seismic studies at Laxemar, 2000

Energy Technology Data Exchange (ETDEWEB)

Juhlin, C.; Bergman, B. [Uppsala Univ. (Sweden); Cosma, C.; Keskinen, J.; Enescu, N. [Vibrometric Oy, Helsinki (Finland)

2002-02-01

Vertical seismic profile (VSP) data were acquired in October 2000 in the 1700 m deep KLX02 borehole, near Laxemar in southeastern Sweden. The objectives of the VSP were to image reflectors in the borehole for correlation with surface seismic and borehole data, study the signal penetration of explosive versus mechanical sources and determine the seismic velocity as a function of depth. Five principal source points were used, one located close to the KLX02 wellhead and 4 others that were offset by about 200 m to 400 m. An explosive source was only used at the wellhead and consisted of 15 grams of dynamite in 90 cm deep shot holes in bedrock. A swept impact seismic source (SIST) was also used at the wellhead, as well as at the other four offset source points. The primary SIST source consisted of a computer controlled mechanical hammer mounted on a tractor. By activating the hammer over a 15 second sweep length, the total energy transferred to the ground is on the same order as that produced by the dynamite. The recorded data are then processed to generate seismic records that are equivalent to a single impact source. A smaller hand held SIST source was also tested at the wellhead. Tests of both the tractor mounted source and dynamite were made at a location offset somewhat from the wellhead at a site containing loose sediments at the surface. Full waveform sonic, resistivity and gamma logs were also acquired in conjunction the VSP survey. A comparison between the explosive and large SIST source shows that comparable energy levels are produced by the two methods. The SIST source appears to be more stable in terms of the energy level, although the frequency content of data are somewhat lower. However, its most significant advantage is the low cost of preparation of the source points and the speed of the acquisition. Numerous reflections are observed on the VSP, as is the case on the surface seismic, implying a complex structure in the vicinity of the KLX02 borehole

Service Learning in Undergraduate Nursing Education: Strategies to Facilitate Meaningful Reflection.

Science.gov (United States)

Schmidt, Nola A; Brown, Janet M

2016-01-01

Service learning is recognized as a valuable pedagogy involving experiential learning, reflection, and reciprocal learning. Students develop critical thinking and social awareness by using the crucial activity of reflecting upon their experiential learning with community partners. The purpose of this paper is to demystify the process of reflection by identifying best practices to enhance reflection and offering suggestions for grading. By understanding "the what" and "the how" of reflection, educators can implement service learning experiences designed to include the essential component of reflection. Strategies for facilitating meaningful reflection are described including descriptions of what students should reflect upon and how to initiate reflection through writing, reading, doing, and telling. Grading rubrics are suggested to facilitate evaluation of student reflection. When properly implemented, service learning encourages students to be good citizens of the world. By using best practices associated with reflection, students can be challenged to think critically about the world and how their service can achieve community goals. Copyright © 2016. Published by Elsevier Inc.

On the radiative transfer problem in a spherical medium subject to Fresnel's reflective boundary conditions

International Nuclear Information System (INIS)

Mohammed, M.H.H.

2012-01-01

Radiation transfer problem for anisotropic scattering in a spherical homogeneous, turbid medium with angular dependent (specular) and diffuse reflecting boundary is considered. The angular dependent reflectivity of the boundary is considered as Fresnel's reflection probability function. The solution of the problem containing an energy source in a medium of specular and diffuse reflecting boundaries is given in terms of the solution of the source-free problem. The source-free problem for anisotropic scattering through a homogeneous solid sphere and two concentric spheres is solved by using the Pomraning- Eddington approximation method. This method transform the integro-differential equation into two differential equations for the radiance g (x) and net flux q (x) which has an analytical solution in terms of the modified Bessel function. Two different weight functions are used to verify the boundary conditions and so, find the solution constants. The partial heat fluxes at the boundaries of a solid sphere and spherical shell of transparent and reflecting boundaries are calculated. The media are taken with or without internal black-body radiation. The calculations are carried out for various values of refractive index and different radii. The results are compared with those of the Galerkin technique

Forsmark site investigation. Reflection seismic studies in the Forsmark area, 2004: Stage 2

Energy Technology Data Exchange (ETDEWEB)

Juhlin, Christopher; Palm, Hans [Uppsala Univ. (Sweden). Dept. of Earth Sciences

2005-06-15

Reflection seismic data were acquired in the Fall of 2004 in the Forsmark area, located about 140 km north of Stockholm, Sweden. The Forsmark area has been targeted by SKB as a possible storage site for spent nuclear fuel. About 25 km of high resolution (nominal source and receiver spacing of maximum 10 m and a minimum of 160 active channels) seismic data were acquired along 10 profiles, varying in length from about 1 km to over 4 km. Three of these profiles are extensions of profiles that were acquired in 2002 (Stage 1). While the 2002 Stage 1 profiles were geared towards acquiring data from within the relatively undeformed lens, the current study focused on acquiring data from the boundaries of the lens. Data acquisition was also concentrated towards the western part of the candidate area. Data were acquired using a combination of the same explosive source as in Stage 1 (1575 g of explosives) and the VIBSIST mechanical source consisting of an industrial hammer mounted on a tractor. Earlier tests in Laxemar had shown that the VIBSIST source gives comparable data to the explosive source and is less expensive. It can also be used in areas where explosives are prohibited, such as close to the nuclear power plant. At present, the source cannot be used in the terrain, therefore an explosive component is still required. About 80% of the 2100 source points were activated using the VIBSIST system. Stacked sections from the new profiles are generally consistent with the Stage 1 results. Reflections from the prominent south dipping A1 reflector can be observed on most profiles, however, it is not clear if it can be traced all the way to the surface. Neither is it clearly observed below the power plant, suggesting its lateral extent is limited to the west. Instead, a gently east dipping reflector (B8) is interpreted below the power plant. Reflections consistent with the A2 reflector are also found on two profiles, but cannot be traced very far to the south, suggesting that

Source Determination of Red Gel Pen Inks using Raman Spectroscopy and Attenuated Total Reflectance Fourier Transform Infrared Spectroscopy combined with Pearson's Product Moment Correlation Coefficients and Principal Component Analysis.

Science.gov (United States)

Mohamad Asri, Muhammad Naeim; Mat Desa, Wan Nur Syuhaila; Ismail, Dzulkiflee

2018-01-01

The potential combination of two nondestructive techniques, that is, Raman spectroscopy (RS) and attenuated total reflectance-fourier transform infrared (ATR-FTIR) spectroscopy with Pearson's product moment correlation (PPMC) coefficient (r) and principal component analysis (PCA) to determine the actual source of red gel pen ink used to write a simulated threatening note, was examined. Eighteen (18) red gel pens purchased from Japan and Malaysia from November to December 2014 where one of the pens was used to write a simulated threatening note were analyzed using RS and ATR-FTIR spectroscopy, respectively. The spectra of all the red gel pen inks including the ink deposited on the simulated threatening note gathered from the RS and ATR-FTIR analyses were subjected to PPMC coefficient (r) calculation and principal component analysis (PCA). The coefficients r = 0.9985 and r = 0.9912 for pairwise combination of RS and ATR-FTIR spectra respectively and similarities in terms of PC1 and PC2 scores of one of the inks to the ink deposited on the simulated threatening note substantiated the feasibility of combining RS and ATR-FTIR spectroscopy with PPMC coefficient (r) and PCA for successful source determination of red gel pen inks. The development of pigment spectral library had allowed the ink deposited on the threatening note to be identified as XSL Poppy Red (CI Pigment Red 112). © 2017 American Academy of Forensic Sciences.

Using children's picture books for reflective learning in nurse education.

Science.gov (United States)

Crawley, Josephine; Ditzel, Liz; Walton, Sue

2012-08-01

One way in which nursing students may build their practice is through reflective learning from stories. Stories in children's literature offer a special source of narratives that enable students to build empathy and to examine and reconstruct their personal concepts around human experience. Illustrated storybooks written for children are a particularly attractive teaching resource, as they tend to be short, interesting, colourful and easy to read. Yet, little has been written about using such books as a reflective learning tool for nursing students. In this article we describe how we use two children's books and McDrury and Alterio's (2002) 'Reflective Learning through Storytelling' model to educate first year nursing students about loss, grief and death.

How Do I Know That My Supervision Is Reflective? Identifying Factors and Validity of the Reflective Supervision Rating Scale

Science.gov (United States)

Gallen, Robert T.; Ash, Jordana; Smith, Conner; Franco, Allison; Willford, Jennifer A.

2016-01-01

Reflective supervision and consultation (RS/C) is often defined as a "relationship for learning"(Fenichel, 1992, p.9). As such, measurement tools should include the perspective of each participant in the supervisory relationship when assessing RS/C fidelity, delivery quality, and the supervisee's experience. The Reflective Supervision…

Reflection tomography from pre-stack migrated images; Tomographie de reflexion a partir des images migrees avant addition

Energy Technology Data Exchange (ETDEWEB)

Adler, F

1996-10-29

The application of reflection tomography to data from complex geological structures is very interesting in the hydrocarbons exploration. Indeed, it contributes to localize the hydrocarbons potential traps. The used reflection tomography method is faced with two major difficulties. Travel time picking is difficult or impossible in seismic time sections. The processing of multiple arrival travel times needs an adequate formulation of reflection tomography. In order to solve the first problem, we adopt the approach of the SMART (Sequential Migration Aided Reflection Tomography) method which is an original method for the implementation of migration velocity analysis. The velocity model is automatically calculated by reflection tomography. The kinematic data set for reflection tomography is constructed from pre-stack depth-migrated images that are interpreted in the chosen migration configuration. For the implementation of the SMART method in the common-offset domain, we propose an original formulation of reflection tomography that takes multiple arrival travel times, which are calculated from common-offset migrated images, into account. In this new formulation, we look for a model such that a modelling, which consists in shooting in this model from the source locations with some ray parameters at the source, matches some emergence conditions: for each offset, the rays emerge at the receiver locations (given by the offset) with the same travel times and the same travel time slopes as observed in the associated common-offset section. These conditions constitute the kinematic data set for tomographic inversion. The common-offset travel time slope is the difference between the ray parameter at the receiver and the ray parameter at the source. Therefore, the ray parameter at the source is an unknown and has to be determined together with the model parameters during inversion. (author)

Thoughts on Reflection (Editorial

Directory of Open Access Journals (Sweden)

Denise Koufogiannakis

2010-06-01

Full Text Available There has been some acknowledgement in the published literature that reflection is a crucial element of the evidence based library and information practice (EBLIP model we have adopted (Booth 2004, 2006; Grant 2007; Helliwell 2007. As we work through a problem and try to incorporate the best available evidence into our decision making, reflection is required at several stages, including the very identification of the problem through to our assessment of the process itself and what we have learned in order to inform future practice. However, reflection and reflective writing have not fully been integrated into the process we espouse, and very little has been done to look more closely at this element of the model and how it can be integrated into professional learning.In a recently published research article, Sen (2010 confirms the relationship between reflection and several aspects of professional practice. These include critical review and decision making, two aspects that are tied closely to the evidence based process. Sen notes: Students were more likely to show evidence of learning, self‐development, the ability to review issues crucially, awareness of their own mental functions, ability to make decision [sic] and being empowered when they had mastered the art of reflective practice and the more deeply analytical reflective writing. (p.84 EBLIP (the journal tries to incorporate elements of reflection within the articles we publish. While we clearly believe in the need for our profession to do quality research and publish that research so that it can be accessible to practitioners, we also know that research cannot be looked at in isolation. Our evidence summaries are one way of reflecting critically on previously published research, and in the same vein, our classics bring older research studies back to the foreground. This work needs to continue to be discussed and looked at for its impact on our profession.More directly, the Using

Some general reflections on open-quotes long pulseclose quotes neutron sources

International Nuclear Information System (INIS)

Bauer, G.S.

1995-01-01

A long pulse spallation neutron source (LPSS) having about 20 times more time average thermal flux than its short pulse counterpart (SPSS) at the same proton beam power and featuring a pronounced time structure not available on CW sources (CWNS) of equal time average flux can in principle host instruments typical for both classes of facilities. While the need for additional choppers introduces some restrictions on inverted time of flight techniques typical for SPSS and high incident neutron energies are not easier to use on LPSS than on CWNS, taking advantage of the pulsed nature of the neutron flux can enhance significantly the performance of direct time of flight instruments and of crystal spectrometers or diffractometers. In the paper some of the options are reviewed in a general manner and criteria are discussed which can be used to optimize the performance enhancement

Reflection and Transmission of a Focused Finite Amplitude Sound Beam Incident on a Curved Interface

Science.gov (United States)

Makin, Inder Raj Singh

Reflection and transmission of a finite amplitude focused sound beam at a weakly curved interface separating two fluid-like media are investigated. The KZK parabolic wave equation, which accounts for thermoviscous absorption, diffraction, and nonlinearity, is used to describe the high intensity focused beam. The first part of the work deals with the quasilinear analysis of a weakly nonlinear beam after its reflection and transmission from a curved interface. A Green's function approach is used to define the field integrals describing the primary and the nonlinearly generated second harmonic beam. Closed-form solutions are obtained for the primary and second harmonic beams when a Gaussian amplitude distribution at the source is assumed. The second part of the research uses a numerical frequency domain solution of the KZK equation for a fully nonlinear analysis of the reflected and transmitted fields. Both piston and Gaussian sources are considered. Harmonic components generated in the medium due to propagation of the focused beam are evaluated, and formation of shocks in the reflected and transmitted beams is investigated. A finite amplitude focused beam is observed to be modified due to reflection and transmission from a curved interface in a manner distinct from that in the case of a small signal beam. Propagation curves, beam patterns, phase plots and time waveforms for various parameters defining the source and media pairs are presented, highlighting the effect of the interface curvature on the reflected and transmitted beams. Relevance of the current work to biomedical applications of ultrasound is discussed.

Infrared reflection nebulae in Orion Molecular Cloud

International Nuclear Information System (INIS)

Pendleton, Y.; Werner, M.W.; Capps, R.; Lester, D.; Hawaii Univ., Honolulu; Texas Univ., Austin)

1986-01-01

New observations of Orion Molecular Cloud 2 have been made from 1 to 100 microns using the NASA Infrared Telescope Facility and the Kuiper Airborne Observatory. An extensive program of polarimetry, photometry, and spectrophotometry has shown that the extended emission regions associated with two of the previously known near-infrared sources, IRS 1 and IRS 4, are infrared reflection nebulae, and that the compact sources IRS 1 and IRS 4 are the main luminosity sources in the cloud. The constraints from the far-infrared observations and an analysis of the scattered light from the IRS 1 nebula show that OMC-2/IRS 1 can be characterized by L of 500 solar luminosities or less and T of roughly 1000 K. The near-infrared albedo of the grains in the IRS 1 nebula is greater than 0.08. 27 references

Methods for reducing singly reflected rays on the Wolter-I focusing mirrors of the FOXSI rocket experiment

Science.gov (United States)

Buitrago-Casas, Juan Camilo; Elsner, Ronald; Glesener, Lindsay; Christe, Steven; Ramsey, Brian; Courtade, Sasha; Ishikawa, Shin-nosuke; Narukage, Noriyuki; Turin, Paul; Vievering, Juliana; Athiray, P. S.; Musset, Sophie; Krucker, Säm.

2017-08-01

In high energy solar astrophysics, imaging hard X-rays by direct focusing offers higher dynamic range and greater sensitivity compared to past techniques that used indirect imaging. The Focusing Optics X-ray Solar Imager (FOXSI) is a sounding rocket payload that uses seven sets of nested Wolter-I figured mirrors together with seven high-sensitivity semiconductor detectors to observe the Sun in hard X-rays through direct focusing. The FOXSI rocket has successfully flown twice and is funded to fly a third time in summer 2018. The Wolter-I geometry consists of two consecutive mirrors, one paraboloid and one hyperboloid, that reflect photons at grazing angles. Correctly focused X-rays reflect once per mirror segment. For extended sources, like the Sun, off-axis photons at certain incident angles can reflect on only one mirror and still reach the focal plane, generating a background pattern of singly reflected rays (i.e., ghost rays) that can limit the sensitivity of the observation to faint, focused sources. Understanding and mitigating the impact of the singly reflected rays on the FOXSI optical modules will maximize the instruments' sensitivity to background-limited sources. We present an analysis of the FOXSI singly reflected rays based on ray-tracing simulations and laboratory measurements, as well as the effectiveness of different physical strategies to reduce them.

Developement of a Light Attenuator Based on Glassy Reflections ...

African Journals Online (AJOL)

The light intensity control of a luminous source is a very important operation in many optical applications. Several types of light attenuator exploiting different optical phenomena like diffraction, absorption, and reflection exist and they differ principally in the maximum attenuation rate, the control range, the sensitivity and the ...

Normal Reflection Characteristics of One-Dimensional Unsteady Flow Shock Waves on Rigid Walls from Pulse Discharge in Water

Directory of Open Access Journals (Sweden)

Dong Yan

2017-01-01

Full Text Available Strong shock waves can be generated by pulse discharge in water, and the characteristics due to the shock wave normal reflection from rigid walls have important significance to many fields, such as industrial production and defense construction. This paper investigates the effects of hydrostatic pressures and perturbation of wave source (i.e., charging voltage on normal reflection of one-dimensional unsteady flow shock waves. Basic properties of the incidence and reflection waves were analyzed theoretically and experimentally to identify the reflection mechanisms and hence the influencing factors and characteristics. The results indicated that increased perturbation (i.e., charging voltage leads to increased peak pressure and velocity of the reflected shock wave, whereas increased hydrostatic pressure obviously inhibited superposition of the reflection waves close to the rigid wall. The perturbation of wave source influence on the reflected wave was much lower than that on the incident wave, while the hydrostatic pressure obviously affected both incident and reflection waves. The reflection wave from the rigid wall in water exhibited the characteristics of a weak shock wave, and with increased hydrostatic pressure, these weak shock wave characteristics became more obvious.

A Study on Conjugate Heat Transfer Analysis of Reactor Vessel including Irradiated Structural Heat Source

Energy Technology Data Exchange (ETDEWEB)

Yi, Kunwoo; Cho, Hyuksu; Im, Inyoung; Kim, Eunkee [KEPCO EnC, Daejeon (Korea, Republic of)

2015-10-15

Though Material reliability programs (MRPs) have a purpose to provide the evaluation or management methodologies for the operating RVI, the similar evaluation methodologies can be applied to the APR1400 fleet in the design stage for the evaluation of neutron irradiation effects. The purposes of this study are: to predict the thermal behavior whether or not irradiated structure heat source; to evaluate effective thermal conductivity (ETC) in relation to isotropic and anisotropic conductivity of porous media for APR1400 Reactor Vessel. The CFD simulations are performed so as to evaluate thermal behavior whether or not irradiated structure heat source and effective thermal conductivity for APR1400 Reactor Vessel. In respective of using irradiated structure heat source, the maximum temperature of fluid and core shroud for isotropic ETC are 325.8 .deg. C, 341.5 .deg. C. The total amount of irradiated structure heat source is about 5.41 MWth and not effect to fluid temperature.

An Access Control Framework for Reflective Middleware

Institute of Scientific and Technical Information of China (English)

Gang Huang; Lian-Shan Sun

2008-01-01

Reflective middleware opens up the implementation details of middleware platform and applications at runtime for improving the adaptability of middleware-based systems. However, such openness brings new challenges to access control of the middleware-based systems.Some users can access the system via reflective entities, which sometimes cannot be protected by access control mechanisms of traditional middleware. To deliver high adaptability securely, reflective middleware should be equipped with proper access control mechanisms for potential access control holes induced by reflection. One reason of integrating these mechanisms in reflective middleware is that one goal of reflective middleware is to equip applications with reflection capabilities as transparent as possible. This paper studies how to design a reflective J2EE middlewarePKUAS with access control in mind. At first, a computation model of reflective system is built to identify all possible access control points induced by reflection. Then a set of access control mechanisms, including the wrapper of MBeans and a hierarchy of Java class loaders, are equipped for controlling the identified access control points. These mechanisms together with J2EE access control mechanism form the access control framework for PKUAS. The paper evaluates the security and the performance overheads of the framework in quality and quantity.

Combining inter-source seismic interferometry and source-receiver interferometry for deep local imaging

NARCIS (Netherlands)

Liu, Y.; Arntsen, B.; Wapenaar, C.P.A.; Van der Neut, J.R.

2014-01-01

The virtual source method has been applied successfully to retrieve the impulse response between pairs of receivers in the subsurface. This method is further improved by an updown separation prior to the crosscorrelation to suppress the reflections from the overburden and the free surface. In a

Gradient SiNO anti-reflective layers in solar selective coatings

Science.gov (United States)

Ren, Zhifeng; Cao, Feng; Sun, Tianyi; Chen, Gang

2017-08-01

A solar selective coating includes a substrate, a cermet layer having nanoparticles therein deposited on the substrate, and an anti-reflection layer deposited on the cermet layer. The cermet layer and the anti-reflection layer may each be formed of intermediate layers. A method for constructing a solar-selective coating is disclosed and includes preparing a substrate, depositing a cermet layer on the substrate, and depositing an anti-reflection layer on the cermet layer.

Reflective and Non-conscious Responses to Exercise Images.

Science.gov (United States)

Cope, Kathryn; Vandelanotte, Corneel; Short, Camille E; Conroy, David E; Rhodes, Ryan E; Jackson, Ben; Dimmock, James A; Rebar, Amanda L

2017-01-01

Images portraying exercise are commonly used to promote exercise behavior and to measure automatic associations of exercise (e.g., via implicit association tests). The effectiveness of these promotion efforts and the validity of measurement techniques partially rely on the untested assumption that the images being used are perceived by the general public as portrayals of exercise that is pleasant and motivating. The aim of this study was to investigate how content of images impacted people's automatic and reflective evaluations of exercise images. Participants ( N = 90) completed a response time categorization task (similar to the implicit association test) to capture how automatically people perceived each image as relevant to Exercise or Not exercise . Participants also self-reported their evaluations of the images using visual analog scales with the anchors: Exercise / Not exercise, Does not motivate me to exercise / Motivates me to exercise, Pleasant / Unpleasant , and Energizing/Deactivating . People tended to more strongly automatically associate images with exercise if the images were of an outdoor setting, presented sport (as opposed to active labor or gym-based) activities, and included young (as opposed to middle-aged) adults. People tended to reflectively find images of young adults more motivating and relevant to exercise than images of older adults. The content of exercise images is an often overlooked source of systematic variability that may impact measurement validity and intervention effectiveness.

Reflective and Non-conscious Responses to Exercise Images

Directory of Open Access Journals (Sweden)

Kathryn Cope

2018-01-01

Full Text Available Images portraying exercise are commonly used to promote exercise behavior and to measure automatic associations of exercise (e.g., via implicit association tests. The effectiveness of these promotion efforts and the validity of measurement techniques partially rely on the untested assumption that the images being used are perceived by the general public as portrayals of exercise that is pleasant and motivating. The aim of this study was to investigate how content of images impacted people's automatic and reflective evaluations of exercise images. Participants (N = 90 completed a response time categorization task (similar to the implicit association test to capture how automatically people perceived each image as relevant to Exercise or Not exercise. Participants also self-reported their evaluations of the images using visual analog scales with the anchors: Exercise/Not exercise, Does not motivate me to exercise/Motivates me to exercise, Pleasant/Unpleasant, and Energizing/Deactivating. People tended to more strongly automatically associate images with exercise if the images were of an outdoor setting, presented sport (as opposed to active labor or gym-based activities, and included young (as opposed to middle-aged adults. People tended to reflectively find images of young adults more motivating and relevant to exercise than images of older adults. The content of exercise images is an often overlooked source of systematic variability that may impact measurement validity and intervention effectiveness.

The Effects of Coaching Using a Reflective Framework on Early Childhood Science Teachers' Depth of Reflection and Change in Practice

Science.gov (United States)

Bloomquist, Debra L.

This embedded-mixed methods study examined if the use of a reflective framework with guiding prompts could support early childhood science teachers in improving their reflective practice and subsequently changing their pedagogy. It further investigated whether type of cognitive coaching group, individual or collaborative, impacted teacher depth of reflection and change in practice. Data included teacher reflections that were rated using the Level of Reflection-On-Action Assessment, reflective codes and inductive themes, as well as videos of participants lessons coded using the SCIIENCE instrument. Findings demonstrated that through guided reflection, teachers developed reflective thinking skills, and through this reflection became more critical and began to improve their pedagogical practice. Further findings supported that collaborative cognitive coaching may not be the most effective professional development for all teachers; as some teachers in the study were found to have difficulty improving their reflectivity and thus their teaching practice. Based on these findings it is recommended that coaches and designers of professional development continue to use reflective frameworks with guiding prompts to support teachers in the reflective process, but take into consideration that coaching may need to be differentiated for the various reflective levels demonstrated by teachers. Future studies will be needed to establish why some teachers have difficulty with the reflective process and how coaches or designers of professional development can further assist these teachers in becoming more critical reflectors.

Elastic reflection based waveform inversion with a nonlinear approach

KAUST Repository

Guo, Qiang

2017-08-16

Full waveform inversion (FWI) is a highly nonlinear problem due to the complex reflectivity of the Earth, and this nonlinearity only increases under the more expensive elastic assumption. In elastic media, we need a good initial P-wave velocity and even a better initial S-wave velocity models with accurate representation of the low model wavenumbers for FWI to converge. However, inverting for the low wavenumber components of P- and S-wave velocities using reflection waveform inversion (RWI) with an objective to fit the reflection shape, rather than produce reflections, may mitigate the limitations of FWI. Because FWI, performing as a migration operator, is in preference of the high wavenumber updates along reflectors. We propose a nonlinear elastic RWI that inverts for both the low wavenumber and perturbation components of the P- and S-wave velocities. To generate the full elastic reflection wavefields, we derive an equivalent stress source made up by the inverted model perturbations and incident wavefields. We update both the perturbation and propagation parts of the velocity models in a nested fashion. Applications on synthetic isotropic models and field data show that our method can efficiently update the low and high wavenumber parts of the models.

Elastic reflection based waveform inversion with a nonlinear approach

KAUST Repository

Guo, Qiang; Alkhalifah, Tariq Ali

2017-01-01

Full waveform inversion (FWI) is a highly nonlinear problem due to the complex reflectivity of the Earth, and this nonlinearity only increases under the more expensive elastic assumption. In elastic media, we need a good initial P-wave velocity and even a better initial S-wave velocity models with accurate representation of the low model wavenumbers for FWI to converge. However, inverting for the low wavenumber components of P- and S-wave velocities using reflection waveform inversion (RWI) with an objective to fit the reflection shape, rather than produce reflections, may mitigate the limitations of FWI. Because FWI, performing as a migration operator, is in preference of the high wavenumber updates along reflectors. We propose a nonlinear elastic RWI that inverts for both the low wavenumber and perturbation components of the P- and S-wave velocities. To generate the full elastic reflection wavefields, we derive an equivalent stress source made up by the inverted model perturbations and incident wavefields. We update both the perturbation and propagation parts of the velocity models in a nested fashion. Applications on synthetic isotropic models and field data show that our method can efficiently update the low and high wavenumber parts of the models.

Sensitivity of a search for cosmic ray sources including magnetic field effects

Energy Technology Data Exchange (ETDEWEB)

Urban, Martin; Erdmann, Martin; Mueller, Gero [III. Physikalisches Institut A, RWTH Aachen University (Germany)

2016-07-01

We analyze the sensitivity of a new method investigating correlations between ultra-high energy cosmic rays and extragalactic sources taking into account deflections in the galactic magnetic field. In comparisons of expected and simulated arrival directions of cosmic rays we evaluate the directional characteristics and magnitude of the field. We show that our method is capable of detecting anisotropy in data sets with a low signal fraction.

Teacher Reflective Practice in Jesuit High Schools

Science.gov (United States)

Klug, Joseph H.

2010-01-01

Teachers who engage in reflective practice are more effective and may encourage higher student achievement. The purpose of this study is to explore and describe the methods that teachers use in order to engage in reflective practice. Further, it is essential to gain an understanding of how schools, including Jesuit high schools, promote reflective…

[Sources of leader's confidence in organizations].

Science.gov (United States)

Ikeda, Hiroshi; Furukawa, Hisataka

2006-04-01

The purpose of this study was to examine the sources of confidence that organization leaders had. As potential sources of the confidence, we focused on fulfillment of expectations made by self and others, reflection on good as well as bad job experiences, and awareness of job experiences in terms of commonality, differentiation, and multiple viewpoints. A questionnaire was administered to 170 managers of Japanese companies. Results were as follows: First, confidence in leaders was more strongly related to fulfillment of expectations made by self and others than reflection on and awareness of job experiences. Second, the confidence was weakly related to internal processing of job experiences, in the form of commonality awareness and reflection on good job experiences. And finally, years of managerial experiences had almost no relation to the confidence. These findings suggested that confidence in leaders was directly acquired from fulfillment of expectations made by self and others, rather than indirectly through internal processing of job experiences. Implications of the findings for leadership training were also discussed.

Comparison of the bidirectional reflectance distribution function of various surfaces

International Nuclear Information System (INIS)

Fernandez, R.; Seasholtz, R.G.; Oberle, L.G.; Kadambi, J.R.

1989-01-01

This paper describes the development and use of a system to measure the bidirectional reflectance distribution function (BRDF) of various surfaces. The BRDF measurements are to be used in the analysis and design of optical measurement systems such as laser anemometers. An Ar-ion laser (514 nm) was the light source. Preliminary results are presented for eight samples: two glossy black paints, two flat black paints, black glass, sand-blasted Al, unworked Al, and a white paint. A BaSO4 white reflectance standard was used as the reference sample throughout the tests. 8 refs

Comparative analysis of traditional and alternative energy sources

Directory of Open Access Journals (Sweden)

Adriana Csikósová

2008-11-01

Full Text Available The presented thesis with designation of Comparing analysis of traditional and alternative energy resources includes, on basisof theoretical information source, research in firm, internal data, trends in company development and market, descriptionof the problem and its application. Theoretical information source is dedicated to the traditional and alternative energy resources,reserves of it, trends in using and development, the balance of it in the world, EU and in Slovakia as well. Analysis of the thesisis reflecting profile of the company and the thermal pump market evaluation using General Electric method. While the companyis implementing, except other products, the thermal pumps on geothermal energy base and surround energy base (air, the missionof the comparing analysis is to compare traditional energy resources with thermal pump from the ecological, utility and economic sideof it. The results of the comparing analysis are resumed in to the SWOT analysis. The part of the thesis includes he questionnaire offerfor effectiveness improvement and customer satisfaction analysis, and expected possibilities of alternative energy resources assistance(benefits from the government and EU funds.

Monte Carlo criticality source convergence in a loosely coupled fuel storage system

International Nuclear Information System (INIS)

Blomquist, Roger N.; Gelbard, Ely M.

2003-01-01

The fission source convergence of a very loosely coupled array of 36 fuel subassemblies with slightly non-symmetric reflection is studied. The fission source converges very slowly from a uniform guess to the fundamental mode in which about 40% of the fissions occur in one corner subassembly. Eigenvalue and fission source estimates are analyzed using a set of statistical tests similar to those used in MCNP, including the 'drift-in-mean' test and a new drift-in-mean test using a linear fit to the cumulative estimate drift, the Shapiro-Wilk test for normality, the relative error test, and the '1/N' test. The normality test does not detect a drifting eigenvalue or fission source. Applied to eigenvalue estimates, the other tests generally fail to detect an unconverged solution, but they are sometimes effective when evaluating fission source distributions. None of the tests provides completely reliable indication of convergence, although they can detect nonconvergence. (author)

Reduction of PM emissions from specific sources reflected on key components concentrations of ambient PM10

Science.gov (United States)

Minguillon, M. C.; Querol, X.; Monfort, E.; Alastuey, A.; Escrig, A.; Celades, I.; Miro, J. V.

2009-04-01

The relationship between specific particulate emission control and ambient levels of some PM10 components (Zn, As, Pb, Cs, Tl) was evaluated. To this end, the industrial area of Castellón (Eastern Spain) was selected, where around 40% of the EU glazed ceramic tiles and a high proportion of EU ceramic frits (middle product for the manufacture of ceramic glaze) are produced. The PM10 emissions from the ceramic processes were calculated over the period 2000 to 2007 taking into account the degree of implementation of corrective measures throughout the study period. Abatement systems (mainly bag filters) were implemented in the majority of the fusion kilns for frit manufacture in the area as a result of the application of the Directive 1996/61/CE, leading to a marked decrease in PM10 emissions. On the other hand, ambient PM10 sampling was carried out from April 2002 to July 2008 at three urban sites and one suburban site of the area and a complete chemical analysis was made for about 35 % of the collected samples, by means of different techniques (ICP-AES, ICP-MS, Ion Chromatography, selective electrode and elemental analyser). The series of chemical composition of PM10 allowed us to apply a source contribution model (Principal Component Analysis), followed by a multilinear regression analysis, so that PM10 sources were identified and their contribution to bulk ambient PM10 was quantified on a daily basis, as well as the contribution to bulk ambient concentrations of the identified key components (Zn, As, Pb, Cs, Tl). The contribution of the sources identified as the manufacture and use of ceramic glaze components, including the manufacture of ceramic frits, accounted for more than 65, 75, 58, 53, and 53% of ambient Zn, As, Pb, Cs and Tl levels, respectively (with the exception of Tl contribution at one of the sites). The important emission reductions of these sources during the study period had an impact on ambient key components levels, such that there was a high

Spatial distribution of reflected gamma rays by Monte Carlo simulation

International Nuclear Information System (INIS)

Jehouani, A.; Merzouki, A.; Boutadghart, F.; Ghassoun, J.

2007-01-01

In nuclear facilities, the reflection of gamma rays of the walls and metals constitutes an unknown origin of radiation. These reflected gamma rays must be estimated and determined. This study concerns reflected gamma rays on metal slabs. We evaluated the spatial distribution of the reflected gamma rays spectra by using the Monte Carlo method. An appropriate estimator for the double differential albedo is used to determine the energy spectra and the angular distribution of reflected gamma rays by slabs of iron and aluminium. We took into the account the principal interactions of gamma rays with matter: photoelectric, coherent scattering (Rayleigh), incoherent scattering (Compton) and pair creation. The Klein-Nishina differential cross section was used to select direction and energy of scattered photons after each Compton scattering. The obtained spectra show peaks at 0.511 * MeV for higher source energy. The Results are in good agreement with those obtained by the TRIPOLI code [J.C. Nimal et al., TRIPOLI02: Programme de Monte Carlo Polycinsetique a Trois dimensions, CEA Rapport, Commissariat a l'Energie Atomique.

POST ASYMPTOTIC GIANT BRANCH BIPOLAR REFLECTION NEBULAE: RESULT OF DYNAMICAL EJECTION OR SELECTIVE ILLUMINATION?

International Nuclear Information System (INIS)

Koning, N.; Kwok, Sun; Steffen, W.

2013-01-01

A model for post asymptotic giant branch bipolar reflection nebulae has been constructed based on a pair of evacuated cavities in a spherical dust envelope. Many of the observed features of bipolar nebulae, including filled bipolar lobes, an equatorial torus, searchlight beams, and a bright central light source, can be reproduced. The effects on orientation and dust densities are studied and comparisons with some observed examples are offered. We suggest that many observed properties of bipolar nebulae are the result of optical effects and any physical modeling of these nebulae has to take these factors into consideration.

Photoflash unit having optical system including aspheric lens to enhance light output

International Nuclear Information System (INIS)

English, G.J.

1984-01-01

A photoflash unit employing an optical system or apparatus with improved center beam candle power seconds and zonal lumen seconds from the flash lamp therein, said unit also employing a minimized utilization ratio of lamp-to-package cross-sectional area. Each individual lamp capsule comprises a reflective element, a refractive element (lens), and at least one photoflash lamp (light source). The lens provides for lamp shred magnification so as to fill the cell (capsule) width to thus provide maximum transfer of light to the subject on axis. One embodiment has the light source fused (glued) to the reflector and lens while a second embodiment has an air interface between the source and the optical elements. In both embodiments, the lens is aspheric and substantially covers both the reflector and source

Identifiable images of bystanders extracted from corneal reflections.

Directory of Open Access Journals (Sweden)

Rob Jenkins

Full Text Available Criminal investigations often use photographic evidence to identify suspects. Here we combined robust face perception and high-resolution photography to mine face photographs for hidden information. By zooming in on high-resolution face photographs, we were able to recover images of unseen bystanders from reflections in the subjects' eyes. To establish whether these bystanders could be identified from the reflection images, we presented them as stimuli in a face matching task (Experiment 1. Accuracy in the face matching task was well above chance (50%, despite the unpromising source of the stimuli. Participants who were unfamiliar with the bystanders' faces (n = 16 performed at 71% accuracy [t(15 = 7.64, p<.0001, d = 1.91], and participants who were familiar with the faces (n = 16 performed at 84% accuracy [t(15 = 11.15, p<.0001, d = 2.79]. In a test of spontaneous recognition (Experiment 2, observers could reliably name a familiar face from an eye reflection image. For crimes in which the victims are photographed (e.g., hostage taking, child sex abuse, reflections in the eyes of the photographic subject could help to identify perpetrators.

Properties of light reflected from road signs in active imaging for driving safety

Science.gov (United States)

Halstuch, Aviran; Yitzhaky, Yitzhak

2007-10-01

Night-vision systems in vehicles are a new emerging technology. A crucial problem in active (illumination-based) systems is distortion of images by saturation and blooming, due to strong retro-reflections from road signs. In this work we quantified this phenomenon. We measured the Mueller matrices and the polarization state of the reflected light from three different types of road signs commonly used. Measurements of the reflected intensity were taken also with respect to the angle of reflection. We found that different types of signs have different reflection properties. It is concluded from our measurements that the optimal solution for attenuating the retro-reflected intensity is using a linear horizontal polarized light source and a linear vertical polarizer. Unfortunately, while the performance of this solution is good for two types of road signs, it is less efficient for the third sign type.

Development and validation of a combined phased acoustical radiosity and image source model for predicting sound fields in rooms

DEFF Research Database (Denmark)

Marbjerg, Gerd Høy; Brunskog, Jonas; Jeong, Cheol-Ho

2015-01-01

A model, combining acoustical radiosity and the image source method, including phase shifts on reflection, has been developed. The model is denoted Phased Acoustical Radiosity and Image Source Method (PARISM), and it has been developed in order to be able to model both specular and diffuse...... radiosity by regarding the model as being stochastic. Three methods of implementation are proposed and investigated, and finally, recommendations are made for their use. Validation of the image source method is done by comparison with finite element simulations of a rectangular room with a porous absorber...

Worldwide Marine Seismic Reflection Profiles

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — NGDC maintains a large volume of both Analog and Digital seismic reflection data. Currently only a limited number of lines are available online. Digital data include...

Fostering nature of science teaching in elementary pre-service teachers through developing reflection on teaching and learning

Science.gov (United States)

Pongsanon, Khemmawadee

Although teacher educators have successfully helped K-12 teachers' develop adequate views of NOS, their views have not been transferred to their students. It is evident that K-12 students' understanding of NOS still does not align with the recommendation of the reforms document, indicating that holding an adequate view of NOS is insufficient for teaching NOS effectively. Instead, to teach NOS, teachers must develop the knowledge for translating their understanding of NOS into the forms accessible to students. The current study investigated the influence of four contexts of reflective practice on prospective elementary teachers' learning of how and intention to teach NOS. The participants were 18 pre-service teachers enrolled in a science methods course that was tied to a field experience course. To understand the development of the participants' intentions, knowledge of instructional strategies, and knowledge of assessment for teaching NOS, multiple data were collected throughout the science methods course and the field experience. Data sources included different versions of participants' lesson plans, video recordings of their teaching and teaching debriefings, online weekly teaching reflections, final semester reflection and other artifacts from the methods course. Content analysis was conducted with all data. The data revealed that the participants' knowledge of how and intentions to teach NOS were developed throughout the science methods course. Toward the conclusion of the semester, the participants showed intention to include NOS in their science instruction. With regard to strategies, participants planned to apply explicit reflective NOS instruction in the context of inquiry-based activities and stories from children's literature. They also planned to use age-appropriate language to refer to the targeted NOS aspects. In terms of assessment, by the conclusion of the semester the participants tended to use more formal assessment strategies. They reported

Being a reflective teacher——reflection on group management

Institute of Scientific and Technical Information of China (English)

Pan; Lehui

2015-01-01

<正>Introduction According to Pollard and Triggs(1997),reflective teaching is a process through which the capacity to make such professional judgments can be developed and maintained.Then what is a reflective teacher?Reflective teacher is someone who reflects systematically on her practice in a constant attempt to improve

The Meaning of Reflective Teaching to National Board Certified Teachers

Science.gov (United States)

Carey, Sharlotte F.

2017-01-01

This qualitative study examined how National Board certified teachers (NBCTs) perceive the meaning of reflective teaching and how their perceptions compare to the literature on reflective thinking and teaching. The study included five participants who had completed the National Board certification process. Data collection included three…

Learning Through Reflective Writing: A Teaching Strategy. A Review of: Sen, B. A. (2010. Reflective writing: A management skill. Library Management, 31(1/2, 79-93.

Directory of Open Access Journals (Sweden)

Kristen L. Young

2010-12-01

Full Text Available Objective – To explore student thought on both reflection and reflective writing as a process, and to analyze the writing by the application of clearly defined and identifiable outcomes.Design – Mixed method approach consisting of a qualitative analysis of 116 written reflections from master’s level students as well as a quantitative statistical analysis.Setting –The University of Sheffield masters-level librarianship program’s course INF6005, “Management for LIS.”Subjects – Of the 31 students registered the course during the 2007-2008 academic year, 22 (71%, allowed their reflections to be used for the purposes of research. Of these, 7 students identified themselves as male, and 15 were female. All students included were over 21 years of age and had previous library experience, with varying degrees of management experience in supervisory roles. Not all supervisory experience was gathered within the library domain.Methods –A total of 116 reflective journal entries were submitted by the participating students during the eight month period from October 2008 to May 2009. In order to identify themes, qualitative analysis was applied to the reflective writing responses. Descriptive statistics were also applied to test the hypothesis, illustrate the relationships between reflective writing and outcomes, and locate identifiable outcomes.Main Results – Practising reflection demonstrated benefits for individuals groups both in and outside of the workplace. On the whole, individuals gained the most from reflection and saw it in the most positive light when it was practised as a daily activity. Quantitatively, when students began to master the practice of reflection, they demonstrated an increase in their ability to learn and an overall improvement of self-development and critical thinking skills, and gained a defined awareness of personal mental function. When decision making became easier, students understood they had begun to master

Characterizing the oxygen isotopic composition of phosphate sources to aquatic ecosystems

Science.gov (United States)

Young, M.B.; McLaughlin, K.; Kendall, C.; Stringfellow, W.; Rollog, M.; Elsbury, K.; Donald, E.; Paytan, A.

2009-01-01

The oxygen isotopic composition of dissolved inorganic phosphate (δ18Op) in many aquatic ecosystems is not in isotopic equilibrium with ambient water and, therefore, may reflect the source δ18Op. Identification of phosphate sources to water bodies is critical for designing best management practices for phosphate load reduction to control eutrophication. In order for δ18O p to be a useful tool for source tracking, the δ18Op of phosphate sources must be distinguishable from one another; however, the δ18Op of potential sources has not been well characterized. We measured the δ18O p of a variety of known phosphate sources, including fertilizers, semiprocessed phosphorite ore, particulate aerosols, detergents, leachates of vegetation, soil, animal feces, and wastewater treatment plant effluent. We found a considerable range of δ18Op values (from +8.4 to +24.9‰) for the various sources, and statistically significant differences were found between several of the source types. δ18Op measured in three different fresh water systems was generally not in equilibrium with ambient water. Although there is overlap in δ18Op values among the groups of samples, our results indicate that some sources are isotopically distinct and δ18Op can be used for identifying phosphate sources to aquatic systems.

A reflectivity profilometer for the optical characterisation of graded reflectivity mirrors in the 250 nm - 1100 nm spectral region

International Nuclear Information System (INIS)

Colucci, Alessandro; Nichelatti, Enrico

1998-04-01

It's developed the prototype of an instrument that can be used for the optical characterisation of graded reflectivity mirrors at any wavelength in the spectral region from 250 nm to 1100 nm. The instrument utilises a high-pressure Xe arc lamp as light source. Light is spectrally filtered by means of a grating monochromator. The sample is illuminated with an image of the monochromator exit slit. After reflection from the sample, this image is projected onto a 1024-elements charge-coupled device linear array driven by a digital frame board and interfaced with a personal computer. It's tested the instrument accuracy by comparing measurement results with the corresponding ones obtained by means of a laser scanning technique. Measurement Rms repeatability has been estimated to be approximately of 0.8% [it

Reflection seismic studies in the Forsmark area - stage 1

Energy Technology Data Exchange (ETDEWEB)

Juhlin, Christopher; Bergman Bjoern; Palm, Hans [Uppsala Univ. (Sweden). Dept. of Earth Sciences

2002-10-01

Reflection seismic data were acquired in the Spring of 2002 in the Forsmark area, located about 70 km northeast of Uppsala, Sweden. The Forsmark area has been targeted by SKB as a possible storage site for high level radioactive waste. About 16 km of high resolution seismic data were acquired along five separate profiles varying in length from 2 to 5 km. Non-final source and receiver spacing was 10 m with 100 active channels when recording data from a dynamite source (15-75 g). The profiles were located within a relatively undeformed lens of bedrock that trends in the NW-SE direction. The lens is surrounded by highly deformed rock on all sides. In conjunction with the reflection component of the study, all shots were also recorded on up to eleven 3-component fixed Orion seismographs. These recordings provided long offset data from which a velocity model of the uppermost 400 m of bedrock could be derived. Results from the study show that the bedrock has been well imaged down to depths of at least 3 km. The upper 1000 m of bedrock is much more reflective in the southeastern portion of the lens compared to the northwestern part close to the Forsmark reactors. This is interpreted as the bedrock being more homogeneous in the northwest. However, a major reflective zone (the A1 reflector) is interpreted to dip to the S-SE below this homogeneous bedrock. In the southeastern portion of the lens the orientation of the reflectors is well determined where the profiles cross one another. The general strike of the major reflectors is NE-SW with dips of 20-35 degrees to the southeast.

Shipwreck in the rowing sport community in 1902: reflections on life and death in sport

Directory of Open Access Journals (Sweden)

Carolina Fernandes da Silva

2016-09-01

Full Text Available People usually start thinking about death when something tragic happens, including in the sport context. At the beginning of 20th century, in South Brazil, four rowers died while they practiced their sport, coming back from an excursion to an island near to Porto Alegre, the capital city of Rio Grande do Sul, where they lived. Following the tragedy, the newspapers published details, both of the tragedy itself, and the ensuing commotion of society, with reflections about life, its fragility and death. This sporting tragedy is a suitable example for trying to understand the way we think about death in sport, given its vast newspaper coverage and the effort to remember the event throughout the 20th century. The interpretation of newspaper sources and reflections on the event will also be considered through the lens of the philosophy of existence of Martin Heidegger. The sources revealed that the shipwreck tragedy made it possible for people to realize that being mortal affects us existentially – that we can never return back to this moment (it is fleeting, it is here and then gone, that we have to make choices that we cannot take back, and that we ourselves are finite beings.

Visual Fatigue Evaluation: Improvement of Reflected Glare on Touch Screen for Nuclear Power Plant

International Nuclear Information System (INIS)

Liu, Kang Hung; Yang, Chih Wei; Hwang, Sheue Ling; Liou, Jin Liang

2014-01-01

The purpose of this research is to evaluate the visual fatigue of operators caused by glare problems in the main control room of nuclear power plant. Within the limitation in the main control room, reflectors were set under the light source which generates reflected glare on touch screens. Through avoiding the light directly shines on touch screens, reflected glare were eliminated. This research matched up the setting process of reflectors, evaluated the visual fatigue of operators, and collected user's opinions before reflector setting, after the first setting, and after the second setting. The design of reflectors could refer the result of evaluations and the collection of opinions. Nevertheless, the improvement of reflected glare on touch screens could be verified by this evaluations. The result showed that setting reflectors under the light source could eliminate reflected glare effectively, and the visual fatigue was reduced both on subject and object evaluations. However, the setting direction of reflectors has potential effect on operators' visual fatigue, so the real setting of reflectors still need to be evaluated completely. The near point accommodation could reflect the effect of visual fatigue caused by changes of lighting environment. Thus, the verification of new lighting environment according to the near point accommodation is suggested

Characterization of the Vajont landslide (North-Eastern Italy) by means of reflection and surface wave seismics

Science.gov (United States)

Petronio, Lorenzo; Boaga, Jacopo; Cassiani, Giorgio

2016-05-01

The mechanisms of the disastrous Vajont rockslide (North-Eastern Italy, October 9, 1963) have been studied in great detail over the past five decades. Nevertheless, the reconstruction of the rockslide dynamics still presents several uncertainties, including those related to the accurate estimation of the actual landslide mass. This work presents the results of a geophysical characterization of the Vajont landslide body in terms of material properties and buried geometry. Both aspects add new information to the existing dataset and will help a better understanding of the rockslide failure mechanisms and dynamics. In addition, some general considerations concerning the intricacies of landslide characterization can be drawn, with due attention to potential pitfalls. The employed techniques are: (i) high resolution P-wave reflection, (ii) high resolution SH-wave reflection, (iii) controlled source surface wave analysis. We adopted as a seismic source a vibrator both for P waves and SH waves, using vertical and horizontal geophones respectively. For the surface wave seismic survey we used a heavy drop-weight source and low frequency receivers. Despite the high noise level caused by the fractured conditions of the large rock body, a common situation in landslide studies, we managed to achieve a satisfying imaging quality of the landslide structure thanks to the large number of active channels, the short receiver interval and the test of appropriate seismic sources. The joint use of different seismic techniques help focus the investigation on the rock mass mechanical properties. Results are in good agreement with the available borehole data, the geological sections and the mechanical properties of the rockmass estimated by other studies. In general the proposed approach is likely to be applicable successfully to similar situations where scattering and other noise sources are a typical bottleneck to geophysical data acquisition on landslide bodies.

Application of Response Surface Methodology to study the effect of different calcium sources in fish muscle-alginate restructured products

Directory of Open Access Journals (Sweden)

Helena María Moreno

2011-03-01

Full Text Available Sodium alginate needs the presence of calcium ions to gelify. For this reason, the contribution of the calcium source in a fish muscle mince added by sodium alginate, makes gelification possible, resulting a restructured fish product. The three different calcium sources considered were: Calcium Chloride (CC; Calcium Caseinate (CCa; and Calcium lactate (CLa. Several physical properties were analyzed, including mechanical properties, colour and cooking loss. Response Surface Methodology (RSM was used to determine the contribution of different calcium sources to a restructured fish muscle. The calcium source that modifies the system the most is CC. A combination of CC and sodium alginate weakened mechanical properties as reflected in the negative linear contribution of sodium alginate. Moreover, CC by itself increased lightness and cooking loss. The mechanical properties of restructured fish muscle elaborated were enhanced by using CCa and sodium alginate, as reflected in the negative linear contribution of sodium alginate. Also, CCa increased cooking loss. The role of CLa combined with sodium alginate was not so pronounced in the system discussed here.

Calculating Remote Sensing Reflectance Uncertainties Using an Instrument Model Propagated Through Atmospheric Correction via Monte Carlo Simulations

Science.gov (United States)

Karakoylu, E.; Franz, B.

2016-01-01

First attempt at quantifying uncertainties in ocean remote sensing reflectance satellite measurements. Based on 1000 iterations of Monte Carlo. Data source is a SeaWiFS 4-day composite, 2003. The uncertainty is for remote sensing reflectance (Rrs) at 443 nm.

An improved method to estimate reflectance parameters for high dynamic range imaging

Science.gov (United States)

Li, Shiying; Deguchi, Koichiro; Li, Renfa; Manabe, Yoshitsugu; Chihara, Kunihiro

2008-01-01

Two methods are described to accurately estimate diffuse and specular reflectance parameters for colors, gloss intensity and surface roughness, over the dynamic range of the camera used to capture input images. Neither method needs to segment color areas on an image, or to reconstruct a high dynamic range (HDR) image. The second method improves on the first, bypassing the requirement for specific separation of diffuse and specular reflection components. For the latter method, diffuse and specular reflectance parameters are estimated separately, using the least squares method. Reflection values are initially assumed to be diffuse-only reflection components, and are subjected to the least squares method to estimate diffuse reflectance parameters. Specular reflection components, obtained by subtracting the computed diffuse reflection components from reflection values, are then subjected to a logarithmically transformed equation of the Torrance-Sparrow reflection model, and specular reflectance parameters for gloss intensity and surface roughness are finally estimated using the least squares method. Experiments were carried out using both methods, with simulation data at different saturation levels, generated according to the Lambert and Torrance-Sparrow reflection models, and the second method, with spectral images captured by an imaging spectrograph and a moving light source. Our results show that the second method can estimate the diffuse and specular reflectance parameters for colors, gloss intensity and surface roughness more accurately and faster than the first one, so that colors and gloss can be reproduced more efficiently for HDR imaging.

Source rock

Directory of Open Access Journals (Sweden)

Abubakr F. Makky

2014-03-01

Full Text Available West Beni Suef Concession is located at the western part of Beni Suef Basin which is a relatively under-explored basin and lies about 150 km south of Cairo. The major goal of this study is to evaluate the source rock by using different techniques as Rock-Eval pyrolysis, Vitrinite reflectance (%Ro, and well log data of some Cretaceous sequences including Abu Roash (E, F and G members, Kharita and Betty formations. The BasinMod 1D program is used in this study to construct the burial history and calculate the levels of thermal maturity of the Fayoum-1X well based on calibration of measured %Ro and Tmax against calculated %Ro model. The calculated Total Organic Carbon (TOC content from well log data compared with the measured TOC from the Rock-Eval pyrolysis in Fayoum-1X well is shown to match against the shale source rock but gives high values against the limestone source rock. For that, a new model is derived from well log data to calculate accurately the TOC content against the limestone source rock in the study area. The organic matter existing in Abu Roash (F member is fair to excellent and capable of generating a significant amount of hydrocarbons (oil prone produced from (mixed type I/II kerogen. The generation potential of kerogen in Abu Roash (E and G members and Betty formations is ranging from poor to fair, and generating hydrocarbons of oil and gas prone (mixed type II/III kerogen. Eventually, kerogen (type III of Kharita Formation has poor to very good generation potential and mainly produces gas. Thermal maturation of the measured %Ro, calculated %Ro model, Tmax and Production index (PI indicates that Abu Roash (F member exciting in the onset of oil generation, whereas Abu Roash (E and G members, Kharita and Betty formations entered the peak of oil generation.

Inspiring Reflections

DEFF Research Database (Denmark)

Muchie, Mammo

2011-01-01

A numberof Chris Freeman's colleagues were asked to reflect on what they thought describes his life and work in a few words. Some of the colleagues replied including former SPRU students that were taught or supervised by Chris Freeman. Their views on what they thought were Chris Freeman's defining...... life is not free from fluctuations, cycles, disruptions, crises and destructions both human and ecological. Innovation research ought to position itself to address environmental, financial and economic crises. The third is innovation research for development by addressing not only poverty erdaication...

Seismic source characterization for the 2014 update of the U.S. National Seismic Hazard Model

Science.gov (United States)

Moschetti, Morgan P.; Powers, Peter; Petersen, Mark D.; Boyd, Oliver; Chen, Rui; Field, Edward H.; Frankel, Arthur; Haller, Kathleen; Harmsen, Stephen; Mueller, Charles S.; Wheeler, Russell; Zeng, Yuehua

2015-01-01

We present the updated seismic source characterization (SSC) for the 2014 update of the National Seismic Hazard Model (NSHM) for the conterminous United States. Construction of the seismic source models employs the methodology that was developed for the 1996 NSHM but includes new and updated data, data types, source models, and source parameters that reflect the current state of knowledge of earthquake occurrence and state of practice for seismic hazard analyses. We review the SSC parameterization and describe the methods used to estimate earthquake rates, magnitudes, locations, and geometries for all seismic source models, with an emphasis on new source model components. We highlight the effects that two new model components—incorporation of slip rates from combined geodetic-geologic inversions and the incorporation of adaptively smoothed seismicity models—have on probabilistic ground motions, because these sources span multiple regions of the conterminous United States and provide important additional epistemic uncertainty for the 2014 NSHM.

Positive Stress and Reflective Practice Among Entrepreneurs

Directory of Open Access Journals (Sweden)

Kati Tikkamäki

2016-01-01

Full Text Available While heavy stress loads seem an unavoidable aspect of entrepreneurship, the positive side of stress (often referred to as ‘eustress’ remains a neglected area of research. This paper contributes to entrepreneurship research by linking the research streams of eustress and reflective practice. As a tool for analysing and developing thoughts and actions, reflective practice plays an important role in the interpretative work essential to positive stress experiences. Following an overview of approaches to stress at work, eustress and reflective practice, the paper explores how entrepreneurs experience the role of positive stress and reflective practice in their work and describes the reflective tools utilized by entrepreneurs in promoting eustress. The research process was designed to support reflective dialogue among the 21 Finnish entrepreneurs from different fields who participated in the study, with results based mainly on qualitative interviews. Nine of the interviewed entrepreneurs also kept a positive stress diary, including a three-day physiological measurement analysing their heartbeat variability. The findings suggest that positive stress and reflective practice are intertwined in the experiences of entrepreneurs and illustrate the role of reflective practice as a crucial toolset for promoting positive stress, comprising six reflective tools: studying oneself, changing one’s point of view, putting things into perspective, harnessing a feeling of trust, regulating resources and engaging in dialogue. Individual reflective capabilities vary, and a theory-driven division of reflective practice into individual, social and contextual dimensions is considered useful in understanding those differences. The research offers a starting point for exploring how eustress and reflective practice affect the well-being of entrepreneurs

GAMMA RAY REFLECTION FACTORS FROM CONCRETE

Energy Technology Data Exchange (ETDEWEB)

Chilton, Arthur B.

1963-06-15

By means of the differential dose albedo formula, the field from a point source of gamma radiation near a concrete-air interface is mapped for those conditions in which the distances involved are larger than a meanfree-path in concrete but substantially smaller than a mean-free-path in air. Once the parameters for the albedo formula are selected, the computation of reflection factors can be carried out to any desired degree of accuracy. Computational errors are kept to substantially less than 5% of the resulting output values. (C.E.S.)

Numerical Predictions of Mode Reflections in an Open Circular Duct: Comparison with Theory

Science.gov (United States)

Dahl, Milo D.; Hixon, Ray

2015-01-01

The NASA Broadband Aeroacoustic Stator Simulation code was used to compute the acoustic field for higher-order modes in a circular duct geometry. To test the accuracy of the results computed by the code, the duct was terminated by an open end with an infinite flange or no flange. Both open end conditions have a theoretical solution that was used to compare with the computed results. Excellent comparison for reflection matrix values was achieved after suitable refinement of the grid at the open end. The study also revealed issues with the level of the mode amplitude introduced into the acoustic held from the source boundary and the amount of reflection that occurred at the source boundary when a general nonreflecting boundary condition was applied.

"The Fly on the Wall" Reflecting Team Supervision.

Science.gov (United States)

Prest, Layne E.; And Others

1990-01-01

Adapts reflecting team concept, a practical application of constructivist ideas, for use in group supervision. Evolving model includes a focus on the unique "fly on the wall" perspective of the reflecting team. Trainees are introduced to a multiverse of new ideas and perspectives in a context which integrates some of the most challenging…

Minimal BRDF Sampling for Two-Shot Near-Field Reflectance Acquisition

DEFF Research Database (Denmark)

Xu, Zexiang; Nielsen, Jannik Boll; Yu, Jiyang

2016-01-01

We develop a method to acquire the BRDF of a homogeneous flat sample from only two images, taken by a near-field perspective camera, and lit by a directional light source. Our method uses the MERL BRDF database to determine the optimal set of lightview pairs for data-driven reflectance acquisition...

Reflectance of Antarctic surfaces from multispectral radiometers: The correction of atmospheric effects

International Nuclear Information System (INIS)

Zibordi, G.; Maracci, G.

1993-01-01

Monitoring reflectance of polar icecaps has relevance in climate studies. In fact, climate changes produce variations in the morphology of ice and snow covers, which are detectable as surface reflectance change. Surface reflectance can be retrieved from remotely sensed data. However, absolute values independent of atmospheric turbidity and surface altitude can only be obtained after removing masking effects of the atmosphere. An atmospheric correction model, accounting for surface and sensor altitudes above sea level, is described and validated through data detected over Antarctic surfaces with a Barnes Modular Multispectral Radiometer having bands overlapping those of the Landsat Thematic Mapper. The model is also applied in a sensitivity analysis to investigate error induced in reflectance obtained from satellite data by indeterminacy in optical parameters of atmospheric constituents. Results show that indeterminacy in the atmospheric water vapor optical thickness is the main source of nonaccuracy in the retrieval of surface reflectance from data remotely sensed over Antarctic regions

Directional statistics-based reflectance model for isotropic bidirectional reflectance distribution functions.

Science.gov (United States)

Nishino, Ko; Lombardi, Stephen

2011-01-01

We introduce a novel parametric bidirectional reflectance distribution function (BRDF) model that can accurately encode a wide variety of real-world isotropic BRDFs with a small number of parameters. The key observation we make is that a BRDF may be viewed as a statistical distribution on a unit hemisphere. We derive a novel directional statistics distribution, which we refer to as the hemispherical exponential power distribution, and model real-world isotropic BRDFs as mixtures of it. We derive a canonical probabilistic method for estimating the parameters, including the number of components, of this novel directional statistics BRDF model. We show that the model captures the full spectrum of real-world isotropic BRDFs with high accuracy, but a small footprint. We also demonstrate the advantages of the novel BRDF model by showing its use for reflection component separation and for exploring the space of isotropic BRDFs.

Reflection seismic methods applied to locating fracture zones in crystalline rock

International Nuclear Information System (INIS)

Juhlin, C.

1998-01-01

The reflection seismic method is a potentially powerful tool for identifying and localising fracture zones in crystalline rock if used properly. Borehole sonic logs across fracture zones show that they have reduced P-wave velocities compared to the surrounding intact rock. Diagnostically important S-wave velocity log information across the fracture zones is generally lacking. Generation of synthetic reflection seismic data and subsequent processing of these data show that structures dipping up towards 70 degrees from horizontal can be reliably imaged using surface seismic methods. Two real case studies where seismic reflection methods have been used to image fracture zones in crystalline rock are presented. Two examples using reflection seismic are presented. The first is from the 5354 m deep SG-4 borehole in the Middle Urals, Russia where strong seismic reflectors dipping from 25 to 50 degrees are observed on surface seismic reflection data crossing over the borehole. On vertical seismic profile data acquired in the borehole, the observed P-wave reflectivity is weak from these zones, however, strong converted P to S waves are observed. This can be explained by the source of the reflectors being fracture zones with a high P wave to S wave velocity ratio compared to the surrounding rock resulting in a high dependence on the angle of incidence for the reflection coefficient. A high P wave to S wave velocity ratio (high Poisson's ratio) is to be expected in fluid filled fractured rock. The second case is from Aevroe, SE Sweden, where two 1 km long crossing high resolution seismic reflection lines were acquired in October 1996. An E-W line was shot with 5 m geophone and shotpoint spacing and a N-S one with 10 m geophone and shotpoint spacing. An explosive source with a charge size of 100 grams was used along both lines. The data clearly image three major dipping reflectors in the upper 200 ms (600 m). The dipping ones intersect or project to the surface at/or close to

Source Apportionment of Particle Bound Polycyclic Aromatic Hydrocarbons at an Industrial Location in Agra, India

Directory of Open Access Journals (Sweden)

Anita Lakhani

2012-01-01

Full Text Available 16 US EPA priority polycyclic aromatic hydrocarbons (PAHs were quantified in total suspended ambient particulate matter (TSPM collected from an industrial site in Agra (India using gas chromatography. The major industrial activities in Agra are foundries that previously used coal and coke as fuel in cupola furnaces. These foundries have now switched over to natural gas. In addition, use of compressed natural gas has also been promoted and encouraged in automobiles. This study attempts to apportion sources of PAH in the ambient air and the results reflect the advantages associated with the change of fuel. The predominant PAHs in TSPM include high molecular weight (HMW congeners BghiP, DbA, IP, and BaP. The sum of 16 priority PAHs had a mean value of 72.7 ± 4.7 ng m−3. Potential sources of PAHs in aerosols were identified using diagnostic ratios and principal component analysis. The results reflect a blend of emissions from diesel and natural gas as the major sources of PAH in the city along with contribution from emission of coal, coke, and gasoline.

Reflection-mode x-ray powder diffraction cell for in situ studies of electrochemical reactions

International Nuclear Information System (INIS)

Roberts, G.A.; Stewart, K.D.

2004-01-01

The design and operation of an electrochemical cell for reflection-mode powder x-ray diffraction experiments are discussed. The cell is designed for the study of electrodes that are used in rechargeable lithium batteries. It is designed for assembly in a glove box so that air-sensitive materials, such as lithium foil electrodes and carbonate-based electrolytes with lithium salts, can be used. The cell uses a beryllium window for x-ray transmission and electrical contact. A simple mechanism for compressing the electrodes is included in the design. Sample results for the cell are shown with a Cu Kα source and a position-sensitive detector

Reflectance spectroscopy of pigmented cutaneous benign and malignant lesions

Science.gov (United States)

Borisova, E.; Jeliazkova, Al.; Pavlova, E.; Troyanova, P.; Kundurdjiev, T.; Pavlova, P.; Avramov, L.

2014-10-01

For the DRS measurements of skin benign, dysplastic and malignant lesions in vivo we applied halogen lamp (LS-1, OceanOptics Inc, Dunedin, Fl, USA) as a continuous light source in the region of 400-900 nm, optical probe (6+1 fibers) for the delivery of illumination and diffuse reflected light from the skin investigated and microspectrometer USB4000 (OceanOptics Inc., Dunedin, Fl, USA) for a storage and display of the spectra detected. As a diffuse reflectance standard Spectralon® plate was used to calibrate the spectrometer. The reflectance spectra obtained from normal skin in identical anatomic sites of different patients have similar spectral shape features, slightly differ by the reflectance intensity at different wavelengths, depending on the particular patient' skin phototype. One could find diagnostically important spectral features, related to specific intensity changes for a given wavelength due to specific pigments appearance, slope changes by value and sign for the reflectance spectra curves in a specific spectral range, disappearance or manifestation of minima, related to hemoglobin absorption at 410-420 nm, 543, 575 nm. Based on the observed peculiarities multispectral analysis of the reflectance spectra of the different lesions was used and diagnostically specific features are found. Discrimination using the DRS data obtained between benign compound and dermal nevi (45 cases), dysplastic nevi (17 cases) and pigmented malignant melanoma (41 cases) lesions is achieved with a diagnostic accuracy of 96 % for the benign nevi vs. MM, and 90 % for the dysplastic nevi vs. MM.

Nitrogen enrichment regulates calcium sources in forests

Science.gov (United States)

Hynicka, Justin D.; Pett-Ridge, Julie C.; Perakis, Steven

2016-01-01

Nitrogen (N) is a key nutrient that shapes cycles of other essential elements in forests, including calcium (Ca). When N availability exceeds ecosystem demands, excess N can stimulate Ca leaching and deplete Ca from soils. Over the long term, these processes may alter the proportion of available Ca that is derived from atmospheric deposition vs. bedrock weathering, which has fundamental consequences for ecosystem properties and nutrient supply. We evaluated how landscape variation in soil N, reflecting long-term legacies of biological N fixation, influenced plant and soil Ca availability and ecosystem Ca sources across 22 temperate forests in Oregon. We also examined interactions between soil N and bedrock Ca using soil N gradients on contrasting basaltic vs. sedimentary bedrock that differed 17-fold in underlying Ca content. We found that low-N forests on Ca-rich basaltic bedrock relied strongly on Ca from weathering, but that soil N enrichment depleted readily weatherable mineral Ca and shifted forest reliance toward atmospheric Ca. Forests on Ca-poor sedimentary bedrock relied more consistently on atmospheric Ca across all levels of soil N enrichment. The broad importance of atmospheric Ca was unexpected given active regional uplift and erosion that are thought to rejuvenate weathering supply of soil minerals. Despite different Ca sources to forests on basaltic vs. sedimentary bedrock, we observed consistent declines in plant and soil Ca availability with increasing N, regardless of the Ca content of underlying bedrock. Thus, traditional measures of Ca availability in foliage and soil exchangeable pools may poorly reflect long-term Ca sources that sustain soil fertility. We conclude that long-term soil N enrichment can deplete available Ca and cause forests to rely increasingly on Ca from atmospheric deposition, which may limit ecosystem Ca supply in an increasingly N-rich world.

Sources of Self-Esteem in Work: What's Important for Whom?

Science.gov (United States)

Schwalbe, Michael L.

1988-01-01

A survey of 250 workers in five manufacturing firms examined sources of self-esteem in work. Responses suggest that, in the workplace, self-perceived competence is the most important source of self-esteem, followed by reflected appraisals and social comparisons. (JOW)

The effects of core-reflected waves on finite fault inversions with teleseismic body wave data

Science.gov (United States)

Qian, Yunyi; Ni, Sidao; Wei, Shengji; Almeida, Rafael; Zhang, Han

2017-11-01

Teleseismic body waves are essential for imaging rupture processes of large earthquakes. Earthquake source parameters are usually characterized by waveform analyses such as finite fault inversions using only turning (direct) P and SH waves without considering the reflected phases from the core-mantle boundary (CMB). However, core-reflected waves such as ScS usually have amplitudes comparable to direct S waves due to the total reflection from the CMB and might interfere with the S waves used for inversion, especially at large epicentral distances for long duration earthquakes. In order to understand how core-reflected waves affect teleseismic body wave inversion results, we develop a procedure named Multitel3 to compute Green's functions that contain turning waves (direct P, pP, sP, direct S, sS and reverberations in the crust) and core-reflected waves (PcP, pPcP, sPcP, ScS, sScS and associated reflected phases from the CMB). This ray-based method can efficiently generate synthetic seismograms for turning and core-reflected waves independently, with the flexibility to take into account the 3-D Earth structure effect on the timing between these phases. The performance of this approach is assessed through a series of numerical inversion tests on synthetic waveforms of the 2008 Mw7.9 Wenchuan earthquake and the 2015 Mw7.8 Nepal earthquake. We also compare this improved method with the turning-wave only inversions and explore the stability of the new procedure when there are uncertainties in a priori information (such as fault geometry and epicentre location) or arrival time of core-reflected phases. Finally, a finite fault inversion of the 2005 Mw8.7 Nias-Simeulue earthquake is carried out using the improved Green's functions. Using enhanced Green's functions yields better inversion results as expected. While the finite source inversion with conventional P and SH waves is able to recover large-scale characteristics of the earthquake source, by adding PcP and ScS phases

Students' reflections in a portfolio pilot: highlighting professional issues.

Science.gov (United States)

Haffling, Ann-Christin; Beckman, Anders; Pahlmblad, Annika; Edgren, Gudrun

2010-01-01

Portfolios are highlighted as potential assessment tools for professional competence. Although students' self-reflections are considered to be central in the portfolio, the content of reflections in practice-based portfolios is seldom analysed. To investigate whether students' reflections include sufficient dimensions of professional competence, notwithstanding a standardized portfolio format, and to evaluate students' satisfaction with the portfolio. Thirty-five voluntary final-year medical students piloted a standardized portfolio in a general practice (GP) attachment at Lund University, Sweden. Students' portfolio reflections were based upon documentary evidence from practice, and aimed to demonstrate students' learning. The reflections were qualitatively analysed, using a framework approach. Students' evaluations of the portfolio were subjected to quantitative and qualitative analysis. Among professional issues, an integration of cognitive, affective and practical dimensions in clinical practice was provided by students' reflections. The findings suggested an emphasis on affective issues, particularly on self-awareness of feelings, attitudes and concerns. In addition, ethical problems, clinical reasoning strategies and future communication skills training were subjects of several reflective commentaries. Students' reflections on their consultation skills demonstrated their endeavour to achieve structure in the medical interview by negotiation of an agenda for the consultation, keeping the interview on track, and using internal summarizing. The importance of active listening and exploration of patient's perspective was also emphasized. In students' case summaries, illustrating characteristic attributes of GP, the dominating theme was 'patient-centred care', including the patient-doctor relationship, holistic modelling and longitudinal continuity. Students were satisfied with the portfolio, but improved instructions were needed. A standardized portfolio in a

Geologic sources and concentrations of selenium in the West-Central Denver Basin, including the Toll Gate Creek watershed, Aurora, Colorado, 2003-2007

Science.gov (United States)

Paschke, Suzanne S.; Walton-Day, Katherine; Beck, Jennifer A.; Webbers, Ank; Dupree, Jean A.

2014-01-01

Toll Gate Creek, in the west-central part of the Denver Basin, is a perennial stream in which concentrations of dissolved selenium have consistently exceeded the Colorado aquatic-life standard of 4.6 micrograms per liter. Recent studies of selenium in Toll Gate Creek identified the Denver lignite zone of the non-marine Cretaceous to Tertiary-aged (Paleocene) Denver Formation underlying the watershed as the geologic source of dissolved selenium to shallow ground-water and surface water. Previous work led to this study by the U.S. Geological Survey, in cooperation with the City of Aurora Utilities Department, which investigated geologic sources of selenium and selenium concentrations in the watershed. This report documents the occurrence of selenium-bearing rocks and groundwater within the Cretaceous- to Tertiary-aged Denver Formation in the west-central part of the Denver Basin, including the Toll Gate Creek watershed. The report presents background information on geochemical processes controlling selenium concentrations in the aquatic environment and possible geologic sources of selenium; the hydrogeologic setting of the watershed; selenium results from groundwater-sampling programs; and chemical analyses of solids samples as evidence that weathering of the Denver Formation is a geologic source of selenium to groundwater and surface water in the west-central part of the Denver Basin, including Toll Gate Creek. Analyses of water samples collected from 61 water-table wells in 2003 and from 19 water-table wells in 2007 indicate dissolved selenium concentrations in groundwater in the west-central Denver Basin frequently exceeded the Colorado aquatic-life standard and in some locations exceeded the primary drinking-water standard of 50 micrograms per liter. The greatest selenium concentrations were associated with oxidized groundwater samples from wells completed in bedrock materials. Selenium analysis of geologic core samples indicates that total selenium

Beyond seismic interferometry: imaging the earth's interior with virtual sources and receivers inside the earth

Science.gov (United States)

Wapenaar, C. P. A.; Van der Neut, J.; Thorbecke, J.; Broggini, F.; Slob, E. C.; Snieder, R.

2015-12-01

Imagine one could place seismic sources and receivers at any desired position inside the earth. Since the receivers would record the full wave field (direct waves, up- and downward reflections, multiples, etc.), this would give a wealth of information about the local structures, material properties and processes in the earth's interior. Although in reality one cannot place sources and receivers anywhere inside the earth, it appears to be possible to create virtual sources and receivers at any desired position, which accurately mimics the desired situation. The underlying method involves some major steps beyond standard seismic interferometry. With seismic interferometry, virtual sources can be created at the positions of physical receivers, assuming these receivers are illuminated isotropically. Our proposed method does not need physical receivers at the positions of the virtual sources; moreover, it does not require isotropic illumination. To create virtual sources and receivers anywhere inside the earth, it suffices to record the reflection response with physical sources and receivers at the earth's surface. We do not need detailed information about the medium parameters; it suffices to have an estimate of the direct waves between the virtual-source positions and the acquisition surface. With these prerequisites, our method can create virtual sources and receivers, anywhere inside the earth, which record the full wave field. The up- and downward reflections, multiples, etc. in the virtual responses are extracted directly from the reflection response at the surface. The retrieved virtual responses form an ideal starting point for accurate seismic imaging, characterization and monitoring.

Seismic reflection response from cross-correlations of ambient vibrations on non-conventional hidrocarbon reservoir

Science.gov (United States)

Huerta, F. V.; Granados, I.; Aguirre, J.; Carrera, R. Á.

2017-12-01

Nowadays, in hydrocarbon industry, there is a need to optimize and reduce exploration costs in the different types of reservoirs, motivating the community specialized in the search and development of alternative exploration geophysical methods. This study show the reflection response obtained from a shale gas / oil deposit through the method of seismic interferometry of ambient vibrations in combination with Wavelet analysis and conventional seismic reflection techniques (CMP & NMO). The method is to generate seismic responses from virtual sources through the process of cross-correlation of records of Ambient Seismic Vibrations (ASV), collected in different receivers. The seismic response obtained is interpreted as the response that would be measured in one of the receivers considering a virtual source in the other. The acquisition of ASV records was performed in northern of Mexico through semi-rectangular arrays of multi-component geophones with instrumental response of 10 Hz. The in-line distance between geophones was 40 m while in cross-line was 280 m, the sampling used during the data collection was 2 ms and the total duration of the records was 6 hours. The results show the reflection response of two lines in the in-line direction and two in the cross-line direction for which the continuity of coherent events have been identified and interpreted as reflectors. There is certainty that the events identified correspond to reflections because the time-frequency analysis performed with the Wavelet Transform has allowed to identify the frequency band in which there are body waves. On the other hand, the CMP and NMO techniques have allowed to emphasize and correct the reflection response obtained during the correlation processes in the frequency band of interest. The results of the processing and analysis of ASV records through the seismic interferometry method have allowed us to see interesting results in light of the cross-correlation process in combination with

Quantifying Reflection

DEFF Research Database (Denmark)

Alcock, Gordon Lindsay

2013-01-01

´ These are all based on Blooms taxonomy and levels of competence and form a major part of individual student and group learning portfolios. Key Words :Project-Based learning, Reflective Portfolios, Self assessment, Defining learning gains, Developing learning strategies , Reflections on and for learning....... It contrasts the students’ self-assessment in a range of ‘product’ skills such as Revit, Structural Design, Mathematics of construction, Technical Installations; as well as ‘process’ competencies such as ‘Working in a team’, Sharing knowledge, Maintaining a portfolio and Reflecting ON learning and FOR learning......This paper documents 1st semester student reflections on “learning to learn” in a team-based PBL environment with quantitative and qualitative student reflective feedback on the learning gains of 60 Architectural Technology and Construction Management students at VIA University College, Denmark...

Functional magnetic resonance imaging study of external source memory and its relation to cognitive insight in non-clinical subjects.

Science.gov (United States)

Buchy, Lisa; Hawco, Colin; Bodnar, Michael; Izadi, Sarah; Dell'Elce, Jennifer; Messina, Katrina; Lepage, Martin

2014-09-01

Previous research has linked cognitive insight (a measure of self-reflectiveness and self-certainty) in psychosis with neurocognitive and neuroanatomical disturbances in the fronto-hippocampal neural network. The authors' goal was to use functional magnetic resonance imaging (fMRI) to investigate the neural correlates of cognitive insight during an external source memory paradigm in non-clinical subjects. At encoding, 24 non-clinical subjects travelled through a virtual city where they came across 20 separate people, each paired with a unique object in a distinct location. fMRI data were then acquired while participants viewed images of the city, and completed source recognition memory judgments of where and with whom objects were seen, which is known to involve prefrontal cortex. Cognitive insight was assessed with the Beck Cognitive Insight Scale. External source memory was associated with neural activity in a widespread network consisting of frontal cortex, including ventrolateral prefrontal cortex (VLPFC), temporal and occipital cortices. Activation in VLPFC correlated with higher self-reflectiveness and activation in midbrain correlated with lower self-certainty during source memory attributions. Neither self-reflectiveness nor self-certainty significantly correlated with source memory accuracy. By means of virtual reality and in the context of an external source memory paradigm, the study identified a preliminary functional neural basis for cognitive insight in the VLPFC in healthy people that accords with our fronto-hippocampal theoretical model as well as recent neuroimaging data in people with psychosis. The results may facilitate the understanding of the role of neural mechanisms in psychotic disorders associated with cognitive insight distortions. © 2014 The Authors. Psychiatry and Clinical Neurosciences © 2014 Japanese Society of Psychiatry and Neurology.

Temperature-reflection I

DEFF Research Database (Denmark)

McGady, David A.

2017-01-01

-temperature path integrals for quantum field theories (QFTs) should be T-reflection invariant. Because multi-particle partition functions are equal to Euclidean path integrals for QFTs, we expect them to be T-reflection invariant. Single-particle partition functions though are often not invariant under T......In this paper, we revisit the claim that many partition functions are invariant under reflecting temperatures to negative values (T-reflection). The goal of this paper is to demarcate which partition functions should be invariant under T-reflection, and why. Our main claim is that finite...... that T-reflection is unrelated to time-reversal. Finally, we study the interplay between T-reflection and perturbation theory in the anharmonic harmonic oscillator in quantum mechanics and in Yang-Mills in four-dimensions. This is the first in a series of papers on temperature-reflections....

The seismic reflection inverse problem

International Nuclear Information System (INIS)

Symes, W W

2009-01-01

The seismic reflection method seeks to extract maps of the Earth's sedimentary crust from transient near-surface recording of echoes, stimulated by explosions or other controlled sound sources positioned near the surface. Reasonably accurate models of seismic energy propagation take the form of hyperbolic systems of partial differential equations, in which the coefficients represent the spatial distribution of various mechanical characteristics of rock (density, stiffness, etc). Thus the fundamental problem of reflection seismology is an inverse problem in partial differential equations: to find the coefficients (or at least some of their properties) of a linear hyperbolic system, given the values of a family of solutions in some part of their domains. The exploration geophysics community has developed various methods for estimating the Earth's structure from seismic data and is also well aware of the inverse point of view. This article reviews mathematical developments in this subject over the last 25 years, to show how the mathematics has both illuminated innovations of practitioners and led to new directions in practice. Two themes naturally emerge: the importance of single scattering dominance and compensation for spectral incompleteness by spatial redundancy. (topical review)

The SEA-change Model in Information Literacy: Assessing Information Literacy Development with Reflective Writing

Directory of Open Access Journals (Sweden)

Barbara Anne Sen

2014-07-01

Full Text Available Reflective writing is a key professional skill, and the University of Sheffield Information School seeks to develop this skill in our students through the use of reflective assessments. Reflection has been used as a means of supporting Information Literacy development in the Higher Education context and recent pedagogical IL frameworks highlight the important role of reflection. This paper presents an analysis of Undergraduate students’ reflective writing on one module. The writing is mapped against two models of reflection to understand the nature and depth of the students’ reflection and through this understand their Information literacy development, with the overall aim of improving the teaching and learning experience for the future. Key findings are that students did reflect deeply and identified a number of ways in which they felt their IL had developed (e.g. developing a knowledge of specialist sources, ways they could have improved their information literacy practices (e.g. through storing information in a more organised fashion, and ways that we could improve our teaching (e.g. by providing appropriate scaffolding for the activities.

Multi-frequency acoustic metasurface for extraordinary reflection and sound focusing

Directory of Open Access Journals (Sweden)

Yi-Fan Zhu

2016-12-01

Full Text Available We theoretically and numerically present the design of multi-frequency acoustic metasurfaces (MFAMs with simple structure that can work not only at fundamental frequency, but also at their harmonic frequencies, which breaks the single frequency limitation in conventional resonance-based acoustic metasurfaces. The phase matched condition for achromatic manipulation is discussed. We demonstrate achromatic extraordinary reflection and sound focusing at 1700Hz, 3400Hz, and 5100Hz, that is, they have the same reflection direction and the same focusing position. This significant feature may pave the way to new type of acoustic metasurface, and will also extend acoustic metasurface applications to strongly nonlinear source cases.

Radio-isotope powered light source

International Nuclear Information System (INIS)

Spottiswoode, N.L.; Ryden, D.J.

1979-01-01

The light source described comprises a radioisotope fuel source, thermal insulation against heat loss, a biological shield against the escape of ionizing radiation and a material having a surface which attains incandescence when subject to isotope decay heat. There is then a means for transferring this heat to produce incandescence of the surface and thus emit light. A filter associated with the surface permits a relatively high transmission of visible radiation but has a relatively high reflectance in the infra red spectrum. Such light sources require the minimum of attention and servicing and are therefore suitable for use in navigational aids such as lighthouses and lighted buoys. The isotope fuel sources and thus the insulation and shielding and the incandescent material can be chosen for the use required and several sources, materials, means of housing etc. are detailed. Operation and efficiency are discussed. (U.K.)

Biodiversity Measurement Using Indices Based on Hyperspectral Reflectance on the Coast of Lagos

Science.gov (United States)

Omodanisi, E. O.; Salami, A. T.

2013-12-01

Hyperspectral measurements provide explicit measurements which can be used in the analysis of biodiversity change. This study was carried out in the coastal area of Lagos State, Nigeria. The objective of this study was to determine if gasoline seepage affects vegetation species distribution and reflectance; with the view to analyzing the vegetation condition. To evaluate the potential of different reflectance spectroscopy of species, the ASD Handheld2 Spectrometer was used. Three identified impacted plots of 30m by 30m were selected randomly and a control plot established in relatively undisturbed vegetated areas away from but perpendicular to the source of seepage. Each identified plot and the control consisted of five transects and measurement were taken at every 2m with about four reflectance measurement per sample point, to average out differences in reflectance as a result of different leaf angles. The radiance output of the spectrometer was converted into reflectance using the reflectance of a white reference over a standardized white spectralon panel. Indices such as Normalized Differential Vegetation Index, RedEdge Normalized Difference Vegetation Index, Soil Adjusted Vegetation Index, Ratio Vegetation Index and Volgelmann RedEdge Index 1 were calculated to accurately estimate the chlorophyll content in the vegetation within optimal band wavelength. Shannon-Weiner's index, Spearman's rank correlation and Analysis of Variance were used to analyze the data. Cocos nucifera was observed to be the most dominant species with a relative abundance of 47.27% while Ananas comosus recorded the lowest relative abundance of 21.8%. In the control plot, Cocos nucifera had the highest relative abundance of 42.3% and Mangifera indica with the least relative abundance of 16.7%. The relationship between the indices and chlorophyll content of the vegetation were significantly higher at (p>0.01) for all the indices in all the plots; however, RedEdgeNDVI and VOG1 indices had the

Theory of reflection reflection and transmission of electromagnetic, particle and acoustic waves

CERN Document Server

Lekner, John

2016-01-01

This book deals with the reflection of electromagnetic and particle waves by interfaces. The interfaces can be sharp or diffuse. The topics of the book contain absorption, inverse problems, anisotropy, pulses and finite beams, rough surfaces, matrix methods, numerical methods,  reflection of particle waves and neutron reflection. Exact general results are presented, followed by long wave reflection, variational theory, reflection amplitude equations of the Riccati type, and reflection of short waves. The Second Edition of the Theory of Reflection is an updated and much enlarged revision of the 1987 monograph. There are new chapters on periodically stratified media, ellipsometry, chiral media, neutron reflection and reflection of acoustic waves. The chapter on anisotropy is much extended, with a complete treatment of the reflection and transmission properties of arbitrarily oriented uniaxial crystals. The book gives a systematic and unified treatment reflection and transmission of electromagnetic and particle...

Ultrahigh precision nonlinear reflectivity measurement system for saturable absorber mirrors with self-referenced fluence characterization.

Science.gov (United States)

Orsila, Lasse; Härkönen, Antti; Hyyti, Janne; Guina, Mircea; Steinmeyer, Günter

2014-08-01

Measurement of nonlinear optical reflectivity of saturable absorber devices is discussed. A setup is described that enables absolute accuracy of reflectivity measurements better than 0.3%. A repeatability within 0.02% is shown for saturable absorbers with few-percent modulation depth. The setup incorporates an in situ knife-edge characterization of beam diameters, making absolute reflectivity estimations and determination of saturation fluences significantly more reliable. Additionally, several measures are discussed to substantially improve the reliability of the reflectivity measurements. At its core, the scheme exploits the limits of state-of-the-art digital lock-in technology but also greatly benefits from a fiber-based master-oscillator power-amplifier source, the use of an integrating sphere, and simultaneous comparison with a linear reflectivity standard.

Modification of UV absorption profile of polymer film reflectors to increase solar-weighted reflectance

Science.gov (United States)

Jorgensen, Gary; Gee, Randall C.; White, David

2017-05-02

Provided are reflective thin film constructions including a reduced number of layers, which provides for increased solar-weighted hemispherical reflectance and durability. Reflective films include those comprising an ultraviolet absorbing abrasion resistant coating over a metal layer. Also provided are ultraviolet absorbing abrasion resistant coatings and methods for optimizing the ultraviolet absorption of an abrasion resistant coating. Reflective films disclosed herein are useful for solar reflecting, solar collecting, and solar concentrating applications, such as for the generation of electrical power.

The Reipurth 50 - north infrared source

International Nuclear Information System (INIS)

Casali, M.M.

1991-01-01

Near-infrared imaging, imaging polarimetry and CVF spectroscopy of Re50N reveal the presence of a single illuminating source, IRS1. The extinction around IRS1 seems to be distributed anisotropically, with a lower extinction path to the reflection nebula than in the line-of-sight. IRS1 appears to be a young steep-spectrum object, with the bulk of its IR emission coming from hot dust. Multiple scattering in the tail of the reflection nebula could explain its relatively blue colours away from IRS1. (author)

Cultivating Reflective Practitioners in Technology Preparation: Constructing TPACK through Reflection

Directory of Open Access Journals (Sweden)

Liangyue Lu

2013-12-01

Full Text Available Teaching is a complex profession, which is further complicated by the integration of technology into classrooms. Reflection can help teachers unpack the complexity in their practice. Reflection can be an effective instructional strategy in helping preservice teachers develop technological pedagogical content knowledge (TPACK, the complex and dynamic knowledge necessary for effective technology integration into instruction. In this study, reflective activities were integrated into a Learning By Design (LBD environment, which was created to help preservice teachers develop TPACK. This paper investigated the participants’ TPACK development and examined how reflection helped them construct TPACK. Through content analysis of the participants’ reflective journals, the researcher found that the preservice teachers developed initial TPACK awareness. However, their reflection in technology knowledge and the content aspects of TPACK were limited and superficial. Interviews with the participants showed reflection helped the preservice teachers remember what they learned by describing and elaborating on their in-class experiences, pushed them to think about how to apply what they learned in their future classrooms, and helped them become more reflective and open-minded about using technology in classrooms. Finally, the researcher discussed this study’s implications for teacher educators and researchers.

A direct reflection OLVF debris detector based on dark-field imaging

Science.gov (United States)

Li, Bo; Xi, Yinhu; Feng, Song; Mao, Junhong; Xie, You-Bai

2018-06-01

To solve the problems of monitoring wear debris in black oil, a direct reflection online visual ferrograph (OLVF) debris detector is presented. In current OLVF detectors, a reflected light source is used. The emitted light is reflected by wear debris directly instead of passing through the lube oil. Therefore, the transparency of the lube oil ceases to matter. Two experiments were conducted to validate the wear debris imaging feasibility and effectiveness of the newly developed detector. The results show that the visual feature information of the wear debris can be reliably obtained from black oil by this detector, and it can also be used to track the fast-changing wear of tribopairs at different wear stages. To the best of our knowledge, to date there is no other report for solving this issue.

Applicability of reflection seismic measurements in detailed characterization of crystalline bedrock

International Nuclear Information System (INIS)

Sireni, S.

2011-03-01

Posiva carried out a seismic survey in the access tunnel of the underground research facility ONKALO in 2009. The survey contributes the detailed characterization of the bedrock in the final disposal of spent nuclear fuel. The aim of this work was to examine the geophysical and geological properties of the chosen tunnel intersections to clarify the important characteristics for reflection generation, and evaluate applicability of this survey for characterization of crystalline bedrock. The seismic result consists of 24 projected amplitude images in 12 different angles. The size of an image is 260*300 m. The amount of digitized reflectors is over 100 and all of them could not be included in this work. The study was limited to 14 intersections that were considered important: brittle fault intersections, tunnel-crosscutting fractures, or lithological contacts. Presence of a brittle fault zone or a tunnel-crosscutting fracture limits the suitable bedrock volume for depositing the nuclear fuel canisters, and wide lithological contacts are a common source of reflection. The seismic data was compared to the existing geological, hydrogeological and geophysical data got from the pilot holes and the tunnel. The most important characteristics were fractures: orientation, fillings, and thickness of the fillings, alteration and water leakage. Geophysically interesting was density, seismic velocities and their products: acoustic impedance and synthetic seismograms. Calculated acoustic impedances showed some differences between cases, but they did not indicate the presence of a reflector. The most common cause of reflector was undulating slickensided, highly altered, tunnel-crosscutting fracture that had thick fracture-fillings and water present. Water was included five times in interpreted reflectors. Also few reflectors were connected to varying mineralogy. Few problematic cases occurred, where a geological feature and a reflection did not correlate, and three of the cases with

A climatology of visible surface reflectance spectra

International Nuclear Information System (INIS)

Zoogman, Peter; Liu, Xiong; Chance, Kelly; Sun, Qingsong; Schaaf, Crystal; Mahr, Tobias; Wagner, Thomas

2016-01-01

We present a high spectral resolution climatology of visible surface reflectance as a function of wavelength for use in satellite measurements of ozone and other atmospheric species. The Tropospheric Emissions: Monitoring of Pollution (TEMPO) instrument is planned to measure backscattered solar radiation in the 290–740 nm range, including the ultraviolet and visible Chappuis ozone bands. Observation in the weak Chappuis band takes advantage of the relative transparency of the atmosphere in the visible to achieve sensitivity to near-surface ozone. However, due to the weakness of the ozone absorption features this measurement is more sensitive to errors in visible surface reflectance, which is highly variable. We utilize reflectance measurements of individual plant, man-made, and other surface types to calculate the primary modes of variability of visible surface reflectance at a high spectral resolution, comparable to that of TEMPO (0.6 nm). Using the Moderate-resolution Imaging Spectroradiometer (MODIS) Bidirection Reflectance Distribution Function (BRDF)/albedo product and our derived primary modes we construct a high spatial resolution climatology of wavelength-dependent surface reflectance over all viewing scenes and geometries. The Global Ozone Monitoring Experiment–2 (GOME-2) Lambertian Equivalent Reflectance (LER) product provides complementary information over water and snow scenes. Preliminary results using this approach in multispectral ultraviolet+visible ozone retrievals from the GOME-2 instrument show significant improvement to the fitting residuals over vegetated scenes. - Highlights: • Our goals was visible surface reflectance for satellite trace gas measurements. • Captured the range of surface reflectance spectra through EOF analysis. • Used satellite surface reflectance products for each given scene to anchor EOFs. • Generated a climatology of time/geometry dependent surface reflectance spectra. • Demonstrated potential to

A fiberoptic reflection oximeter.

Science.gov (United States)

Landsman, M L; Knop, N; Kwant, G; Mook, G A; Zijlstra, W G

1978-03-20

A catheter tip oximeter is described consisting of a cardiac catheter containing optical fibers, and incandescent light source, a light detection unit and a processing unit. Half of the optical fibers guide the light to the blood at the tip of the catheter, the other half the backscattered (reflected) light to the detection unit. The detection unit contains a dichroic mirror, transmitting most of the light with lambda less than 800 nm and reflecting most of the light with lambda greater than 900 nm, thus splitting the light into two beams. These pass through interference filters with nominal wavelengths of 640 and 920 nm respectively, and are focused on silicium barrier layer photocells. The photocell signals are amplified and fed into a divider giving the ratio of measuring (R640) and compensating (R920) photocell output. The relationship between log R640/R920 and oxygen saturation is represented by a slightly curved line. The relation may be linearized by subtracting a constant voltage from the divided output before taking the logarithm. The slope of the calibration line is dependent on the total haemoglobin concentration. Nonetheless an average calibration line can be used between 70 and 100% oxygen saturation. For 78 measurements of pig blood samples in this range (haemoglobin concentration between 96 and 161 g.1(-1)), the standard deviation of the difference between the fiberoptic oximeter and a Radiometer OSM1 oxygen saturation meter was 1.9% saturation, for 152 samples over the entire saturation range the standard deviation of the difference was 3.1% saturation. The influence of the flow velocity of blood on the light reflection depends on wavelength as well as on oxygen saturation. Therefore, complete compensation for the flow effect is not possible by simple means.

Methods for measuring the spectral reflectivity of advanced materials at high temperature

International Nuclear Information System (INIS)

Salikhov, T.P.; Kan, V.V.

1993-01-01

For investigation in the domain of advanced materials as well as for new technologies there is an urgent need for knowledge of the spectral reflectivity of the materials specially at high temperatures. However the methods available are mostly intended for measuring the model materials with specular or diffuse reflection surface. This is not quite correct since advanced materials have mixed specular diffuse reflection surfaces. New methods for reflectivity measurements of materials in the visible, near and middle infrared range at high temperature, regardless of surface texture, have been developed. The advantages of the methods proposed are as flows: (a) the facility of performing the reflectivity measurements for materials with mixed specular diffuse reflectance; (b) wide spectral range 0,38-8 micro m; (c) wide temperature range 300-3000 K; (d) high accuracy and rapid measurements. The methods are based on the following principals (i) Diffuse irradiation of the sample surface and the use of Helkholtz reciprocity principle to determine the directional hemispherical reflectivity ii) Pulse polychromatic probing of the sample by additional light source. The first principle excludes the influence of the angular reflection distribution of sample surface on data obtained. The second principle gives the possibility of simultaneous measurements of the reflectivity. The second principle gives the possibility of simultaneous measurements of the reflectivity in wide spectral range. On the basis of these principles for high temperature reflectometers have been developed and discussed here. (author)

Generating Land Surface Reflectance for the New Generation of Geostationary Satellite Sensors with the MAIAC Algorithm

Science.gov (United States)

Wang, W.; Wang, Y.; Hashimoto, H.; Li, S.; Takenaka, H.; Higuchi, A.; Lyapustin, A.; Nemani, R. R.

2017-12-01

The latest generation of geostationary satellite sensors, including the GOES-16/ABI and the Himawari 8/AHI, provide exciting capability to monitor land surface at very high temporal resolutions (5-15 minute intervals) and with spatial and spectral characteristics that mimic the Earth Observing System flagship MODIS. However, geostationary data feature changing sun angles at constant view geometry, which is almost reciprocal to sun-synchronous observations. Such a challenge needs to be carefully addressed before one can exploit the full potential of the new sources of data. Here we take on this challenge with Multi-Angle Implementation of Atmospheric Correction (MAIAC) algorithm, recently developed for accurate and globally robust applications like the MODIS Collection 6 re-processing. MAIAC first grids the top-of-atmosphere measurements to a fixed grid so that the spectral and physical signatures of each grid cell are stacked ("remembered") over time and used to dramatically improve cloud/shadow/snow detection, which is by far the dominant error source in the remote sensing. It also exploits the changing sun-view geometry of the geostationary sensor to characterize surface BRDF with augmented angular resolution for accurate aerosol retrievals and atmospheric correction. The high temporal resolutions of the geostationary data indeed make the BRDF retrieval much simpler and more robust as compared with sun-synchronous sensors such as MODIS. As a prototype test for the geostationary-data processing pipeline on NASA Earth Exchange (GEONEX), we apply MAIAC to process 18 months of data from Himawari 8/AHI over Australia. We generate a suite of test results, including the input TOA reflectance and the output cloud mask, aerosol optical depth (AOD), and the atmospherically-corrected surface reflectance for a variety of geographic locations, terrain, and land cover types. Comparison with MODIS data indicates a general agreement between the retrieved surface reflectance

Studies of the infrared source CRL 2688

International Nuclear Information System (INIS)

Ney, E.P.; Merrill, K.M.; Becklin, E.E.; Neugebauer, G.; Wynn-Williams, C.G.

1975-01-01

Infrared, optical, and radio observations are descirbed of a newly discovered galactic infrared source. Most of the radiation comes from 1/sup double-prime/./sub /5 diameter infrared source at a temperature of about 150 K, but some visible emission in the form of a symmetrical highly polarized reflection nebulosity is also seen. The object could represent either a very early or a very late stage in stellar evolution

THE CHANDRA SOURCE CATALOG

International Nuclear Information System (INIS)

Evans, Ian N.; Primini, Francis A.; Glotfelty, Kenny J.; Anderson, Craig S.; Bonaventura, Nina R.; Chen, Judy C.; Doe, Stephen M.; Evans, Janet D.; Fabbiano, Giuseppina; Galle, Elizabeth C.; Gibbs, Danny G.; Grier, John D.; Hain, Roger M.; Harbo, Peter N.; He Xiangqun; Karovska, Margarita; Kashyap, Vinay L.; Davis, John E.; Houck, John C.; Hall, Diane M.

2010-01-01

The Chandra Source Catalog (CSC) is a general purpose virtual X-ray astrophysics facility that provides access to a carefully selected set of generally useful quantities for individual X-ray sources, and is designed to satisfy the needs of a broad-based group of scientists, including those who may be less familiar with astronomical data analysis in the X-ray regime. The first release of the CSC includes information about 94,676 distinct X-ray sources detected in a subset of public Advanced CCD Imaging Spectrometer imaging observations from roughly the first eight years of the Chandra mission. This release of the catalog includes point and compact sources with observed spatial extents ∼<30''. The catalog (1) provides access to the best estimates of the X-ray source properties for detected sources, with good scientific fidelity, and directly supports scientific analysis using the individual source data; (2) facilitates analysis of a wide range of statistical properties for classes of X-ray sources; and (3) provides efficient access to calibrated observational data and ancillary data products for individual X-ray sources, so that users can perform detailed further analysis using existing tools. The catalog includes real X-ray sources detected with flux estimates that are at least 3 times their estimated 1σ uncertainties in at least one energy band, while maintaining the number of spurious sources at a level of ∼<1 false source per field for a 100 ks observation. For each detected source, the CSC provides commonly tabulated quantities, including source position, extent, multi-band fluxes, hardness ratios, and variability statistics, derived from the observations in which the source is detected. In addition to these traditional catalog elements, for each X-ray source the CSC includes an extensive set of file-based data products that can be manipulated interactively, including source images, event lists, light curves, and spectra from each observation in which a

The Chandra Source Catalog

Science.gov (United States)

Evans, Ian N.; Primini, Francis A.; Glotfelty, Kenny J.; Anderson, Craig S.; Bonaventura, Nina R.; Chen, Judy C.; Davis, John E.; Doe, Stephen M.; Evans, Janet D.; Fabbiano, Giuseppina; Galle, Elizabeth C.; Gibbs, Danny G., II; Grier, John D.; Hain, Roger M.; Hall, Diane M.; Harbo, Peter N.; He, Xiangqun Helen; Houck, John C.; Karovska, Margarita; Kashyap, Vinay L.; Lauer, Jennifer; McCollough, Michael L.; McDowell, Jonathan C.; Miller, Joseph B.; Mitschang, Arik W.; Morgan, Douglas L.; Mossman, Amy E.; Nichols, Joy S.; Nowak, Michael A.; Plummer, David A.; Refsdal, Brian L.; Rots, Arnold H.; Siemiginowska, Aneta; Sundheim, Beth A.; Tibbetts, Michael S.; Van Stone, David W.; Winkelman, Sherry L.; Zografou, Panagoula

2010-07-01

The Chandra Source Catalog (CSC) is a general purpose virtual X-ray astrophysics facility that provides access to a carefully selected set of generally useful quantities for individual X-ray sources, and is designed to satisfy the needs of a broad-based group of scientists, including those who may be less familiar with astronomical data analysis in the X-ray regime. The first release of the CSC includes information about 94,676 distinct X-ray sources detected in a subset of public Advanced CCD Imaging Spectrometer imaging observations from roughly the first eight years of the Chandra mission. This release of the catalog includes point and compact sources with observed spatial extents lsim30''. The catalog (1) provides access to the best estimates of the X-ray source properties for detected sources, with good scientific fidelity, and directly supports scientific analysis using the individual source data; (2) facilitates analysis of a wide range of statistical properties for classes of X-ray sources; and (3) provides efficient access to calibrated observational data and ancillary data products for individual X-ray sources, so that users can perform detailed further analysis using existing tools. The catalog includes real X-ray sources detected with flux estimates that are at least 3 times their estimated 1σ uncertainties in at least one energy band, while maintaining the number of spurious sources at a level of lsim1 false source per field for a 100 ks observation. For each detected source, the CSC provides commonly tabulated quantities, including source position, extent, multi-band fluxes, hardness ratios, and variability statistics, derived from the observations in which the source is detected. In addition to these traditional catalog elements, for each X-ray source the CSC includes an extensive set of file-based data products that can be manipulated interactively, including source images, event lists, light curves, and spectra from each observation in which a

Transport synthetic acceleration with opposing reflecting boundary conditions

Energy Technology Data Exchange (ETDEWEB)

Zika, M R; Adams, M L

2000-02-01

The transport synthetic acceleration (TSA) scheme is extended to problems with opposing reflecting boundary conditions. This synthetic method employs a simplified transport operator as its low-order approximation. A procedure is developed that allows the use of the conjugate gradient (CG) method to solve the resulting low-order system of equations. Several well-known transport iteration algorithms are cast in a linear algebraic form to show their equivalence to standard iterative techniques. Source iteration in the presence of opposing reflecting boundary conditions is shown to be equivalent to a (poorly) preconditioned stationary Richardson iteration, with the preconditioner defined by the method of iterating on the incident fluxes on the reflecting boundaries. The TSA method (and any synthetic method) amounts to a further preconditioning of the Richardson iteration. The presence of opposing reflecting boundary conditions requires special consideration when developing a procedure to realize the CG method for the proposed system of equations. The CG iteration may be applied only to symmetric positive definite matrices; this condition requires the algebraic elimination of the boundary angular corrections from the low-order equations. As a consequence of this elimination, evaluating the action of the resulting matrix on an arbitrary vector involves two transport sweeps and a transmission iteration. Results of applying the acceleration scheme to a simple test problem are presented.

Optical fringe-reflection deflectometry with bundle adjustment

Science.gov (United States)

Xiao, Yong-Liang; Li, Sikun; Zhang, Qican; Zhong, Jianxin; Su, Xianyu; You, Zhisheng

2018-06-01

Liquid crystal display (LCD) screens are located outside of a camera's field of view in fringe-reflection deflectometry. Therefore, fringes that are displayed on LCD screens are obtained through specular reflection by a fixed camera. Thus, the pose calibration between the camera and LCD screen is one of the main challenges in fringe-reflection deflectometry. A markerless planar mirror is used to reflect the LCD screen more than three times, and the fringes are mapped into the fixed camera. The geometrical calibration can be accomplished by estimating the pose between the camera and the virtual image of fringes. Considering the relation between their pose, the incidence and reflection rays can be unified in the camera frame, and a forward triangulation intersection can be operated in the camera frame to measure three-dimensional (3D) coordinates of the specular surface. In the final optimization, constraint-bundle adjustment is operated to refine simultaneously the camera intrinsic parameters, including distortion coefficients, estimated geometrical pose between the LCD screen and camera, and 3D coordinates of the specular surface, with the help of the absolute phase collinear constraint. Simulation and experiment results demonstrate that the pose calibration with planar mirror reflection is simple and feasible, and the constraint-bundle adjustment can enhance the 3D coordinate measurement accuracy in fringe-reflection deflectometry.

CFD Analysis of Water Solitary Wave Reflection

Directory of Open Access Journals (Sweden)

K. Smida

2011-12-01

Full Text Available A new numerical wave generation method is used to investigate the head-on collision of two solitary waves. The reflection at vertical wall of a solitary wave is also presented. The originality of this model, based on the Navier-Stokes equations, is the specification of an internal inlet velocity, defined as a source line within the computational domain for the generation of these non linear waves. This model was successfully implemented in the PHOENICS (Parabolic Hyperbolic Or Elliptic Numerical Integration Code Series code. The collision of two counter-propagating solitary waves is similar to the interaction of a soliton with a vertical wall. This wave generation method allows the saving of considerable time for this collision process since the counter-propagating wave is generated directly without reflection at vertical wall. For the collision of two solitary waves, numerical results show that the run-up phenomenon can be well explained, the solution of the maximum wave run-up is almost equal to experimental measurement. The simulated wave profiles during the collision are in good agreement with experimental results. For the reflection at vertical wall, the spatial profiles of the wave at fixed instants show that this problem is equivalent to the collision process.

NUSTAR and Suzaku x-ray spectroscopy of NGC 4151: Evidence for reflection from the inner accretion disk

Energy Technology Data Exchange (ETDEWEB)

Keck, M. L.; Brenneman, L. W.; Ballantyne, D. R.; Bauer, F.; Boggs, S. E.; Christensen, F. E.; Craig, W. W.; Dauser, T.; Elvis, M.; Fabian, A. C.; Fuerst, F.; García, J.; Grefenstette, B. W.; Hailey, C. J.; Harrison, F. A.; Madejski, G.; Marinucci, A.; Matt, G.; Reynolds, C. S.; Stern, D.; Walton, D. J.; Zoghbi, A.

2015-06-15

We present X-ray timing and spectral analyses of simultaneous 150 ks Nuclear Spectroscopic Telescope Array (NuSTAR) and Suzaku X-ray observations of the Seyfert 1.5 galaxy NGC 4151. We disentangle the continuum emission, absorption, and reflection properties of the active galactic nucleus (AGN) by applying inner accretion disk reflection and absorption-dominated models. With a time-averaged spectral analysis, we find strong evidence for relativistic reflection from the inner accretion disk. We find that relativistic emission arises from a highly ionized inner accretion disk with a steep emissivity profile, which suggests an intense, compact illuminating source. We find a preliminary, near-maximal black hole spin $a\\gt 0.9$ accounting for statistical and systematic modeling errors. We find a relatively moderate reflection fraction with respect to predictions for the lamp post geometry, in which the illuminating corona is modeled as a point source. Through a time-resolved spectral analysis, we find that modest coronal and inner disk reflection (IDR) flux variation drives the spectral variability during the observations. We discuss various physical scenarios for the IDR model and we find that a compact corona is consistent with the observed features.

Spectral reflectance relationships to leaf water stress

Science.gov (United States)

Ripple, William J.

1986-01-01

Spectral reflectance data were collected from detached snapbean leaves in the laboratory with a multiband radiometer. Four experiments were designed to study the spectral response resulting from changes in leaf cover, relative water content of leaves, and leaf water potential. Spectral regions included in the analysis were red (630-690 nm), NIR (760-900 nm), and mid-IR (2.08-2.35 microns). The red and mid-IR bands showed sensitivity to changes in both leaf cover and relative water content of leaves. The NIR was only highly sensitive to changes in leaf cover. Results provided evidence that mid-IR reflectance was governed primarily by leaf moisture content, although soil reflectance was an important factor when leaf cover was less than 100 percent. High correlations between leaf water potentials and reflectance were attributed to covariances with relative water content of leaves and leaf cover.

VALUATION OF OPEN SOURCE SOFTWARE: HOW DO YOU PUT A VALUE ON FREE?

Directory of Open Access Journals (Sweden)

Jesús García-García

2013-04-01

Full Text Available The aim of this study is to assess the financial reporting framework applied to open source software. Open sourcing software developments means sharing technology and resources with communities worldwide to help eliminate the digital divide, create economic opportunity, and support equal access to technology. Therefore, a methodological approach is needed to assess properly the performance and the value generation potential and to put such measure into organizational reports. International financial reporting framework is checked over conditions to allow value recognition of open sourced assets. Linux kernel development value is estimated to reflect worth of open source developments despite absence of book value due to inexistence of a single cost source. Several attempts to estimate a valuation of open source software have been performed previously. However, this study is the first to judge suitability of accounting framework to report on this value. The main finding is that open sourced assets do not fully accomplish conditions to be included in financial reports. We seek to stimulate academic and professional debate about the pursuit of valuation of a large and efficient ecosystem of software innovation, freely available to society.

Negative ion sources

International Nuclear Information System (INIS)

Ishikawa, Junzo; Takagi, Toshinori

1983-01-01

Negative ion sources have been originally developed at the request of tandem electrostatic accelerators, and hundreds of nA to several μA negative ion current has been obtained so far for various elements. Recently, the development of large current hydrogen negative ion sources has been demanded from the standpoint of the heating by neutral particle beam injection in nuclear fusion reactors. On the other hand, the physical properties of negative ions are interesting in the thin film formation using ions. Anyway, it is the present status that the mechanism of negative ion action has not been so fully investigated as positive ions because the history of negative ion sources is short. In this report, the many mechanisms about the generation of negative ions proposed so far are described about negative ion generating mechanism, negative ion source plasma, and negative ion generation on metal surfaces. As a result, negative ion sources are roughly divided into two schemes, plasma extraction and secondary ion extraction, and the former is further classified into the PIG ion source and its variation and Duoplasmatron and its variation; while the latter into reflecting and sputtering types. In the second half of the report, the practical negative ion sources of each scheme are described. If the mechanism of negative ion generation will be investigated more in detail and the development will be continued under the unified know-how as negative ion sources in future, the development of negative ion sources with which large current can be obtained for any element is expected. (Wakatsuki, Y.)

Implementing reflection: insights from pre-registration mental health students.

Science.gov (United States)

Donovan, Moira O

2007-08-01

Reflection and reflective practice continues to be contentious issues in nursing. The focus of this article is the use of reflection by pre-registration mental health students. The broad aim of this preliminary study was to discover student mental health nurses' perceptions of reflection as a learning strategy during clinical placement. Using a constructivist grounded theory methodology [Charmaz, K., 2000. Grounded theory: Objectivist and Constructivist Methods. In: Denzin, N., Lincoln, Y. (Eds.), Handbook of Qualitative Research, second ed. Sage, Thousand Oaks, California], five students were interviewed individually in their clinical placements. Data analysis revealed three major categories: understanding the process of reflection, using reflection in clinical practice, and needing support and guidance. Findings indicated that students were primarily using reflection-on-action, but to varying extents. Overall, students felt that reflection facilitated their learning. Factors were discovered that both helped and hindered students' use of reflection. These included level of preparation to reflect, a limited culture of reflection and the level of support from preceptors, clinical staff, clinical placement co-ordinators, and lecturers. In conclusion, it appears that a collaborative approach between students, Health Service Providers and institutes of nursing is vital for the successful development and implementation of reflective learning strategies in clinical placement. Suggestions are made as to how a collaborative approach may be developed to enhance this process.

The cuticle modulates ultraviolet reflectance of avian eggshells

Directory of Open Access Journals (Sweden)

Daphne C. Fecheyr-Lippens

2015-07-01

Full Text Available Avian eggshells are variedly coloured, yet only two pigments, biliverdin and protoporphyrin IX, are known to contribute to the dramatic diversity of their colours. By contrast, the contributions of structural or other chemical components of the eggshell are poorly understood. For example, unpigmented eggshells, which appear white to the human eye, vary in their ultraviolet (UV reflectance, which may be detectable by birds. We investigated the proximate mechanisms for the variation in UV-reflectance of unpigmented bird eggshells using spectrophotometry, electron microscopy, chemical analyses, and experimental manipulations. We specifically tested how UV-reflectance is affected by the eggshell cuticle, the outermost layer of most avian eggshells. The chemical dissolution of the outer eggshell layers, including the cuticle, increased UV-reflectance for only eggshells that contained a cuticle. Our findings demonstrate that the outer eggshell layers, including the cuticle, absorb UV-light, probably because they contain higher levels of organic components and other chemicals, such as calcium phosphates, compared to the predominantly calcite-based eggshell matrix. These data highlight the need to examine factors other than the known pigments in studies of avian eggshell colour.

Source term reduction at DAEC (including stellite ball recycling)

International Nuclear Information System (INIS)

Smith, R.; Schebler, D.

1995-01-01

The Duane Arnold Energy Center was seeking methods to reduce dose rates from the drywell due to Co-60. Duane Arnold is known in the industry to have one of the highest drywell dose rates from the industry standardized 'BRAC' point survey. A prime method to reduce dose rates due to Co-60 is the accelerated replacement of stellite pins and rollers in control rod blades due to their high stellite (cobalt) content. Usually the cobalt content in alloys of stellite is greater than 60% cobalt by weight. During the RFO-12 refueling outage at Duane Arnold, all of the remaining cobalt bearing control rod blades were replaced and new stellite free control rod blades were installed in the core. This left Duane Arnold with the disposal of highly radioactive stellite pins and rollers. The processing of control rod blades for disposal is a very difficult evolution. First, the velocity limiter (a bottom portion of the component) and the highly radioactive upper stellite control rod blade ins and rollers are separated from the control rod blade. Next, the remainder of the control rod blade is processed (chopped and/or crushed) to aid packaging the waste for disposal. The stellite bearings are then often carefully placed in with the rest of the waste in a burial liner to provide shielding for disposal or more often are left as 'orphans' in the spent fuel pool because their high specific activity create shipping and packaging problems. Further investigation by the utility showed that the stellite balls and pins could be recycled to a source manufacturer rather than disposed of in a low-level burial site. The cost savings to the utility was on the order of $200,000 with a gross savings of $400,000 in savings in burial site charges. A second advantage of the recycling of the stellite pins and rollers was a reduction in control in radioactive waste shipments

Low-reflection beam refractions by ultrathin Huygens metasurface

International Nuclear Information System (INIS)

Jia, Sheng Li; Wan, Xiang; Fu, Xiao Jian; Zhao, Yong Jiu; Cui, Tie Jun

2015-01-01

We propose a Huygens source unit cell to develop an ultrathin low-reflection metasurface, which could provide extreme controls of phases of the transmitted waves. Both electric and magnetic currents are supported by the proposed unit cell, thus leading to highly efficient and full controls of phases. The coupling between electric and magnetic responses is negligible, which will significantly reduce the difficulty of design. Since the unit cell of metasurface is printed on two bonded boards, the fabrication process is simplified and the thickness of metasurface is reduced. Based on the proposed unit cell, a beam-refracting metasurface with low-reflection is designed and manufactured. Both near-field and far-field characteristics of the beam-refracting metasurface are investigated by simulations and measurements, which indicate that the proposed Huygens metasurface performs well in controlling electromagnetic waves

Does the cognitive reflection test measure cognitive reflection? A mathematical modeling approach.

Science.gov (United States)

Campitelli, Guillermo; Gerrans, Paul

2014-04-01

We used a mathematical modeling approach, based on a sample of 2,019 participants, to better understand what the cognitive reflection test (CRT; Frederick In Journal of Economic Perspectives, 19, 25-42, 2005) measures. This test, which is typically completed in less than 10 min, contains three problems and aims to measure the ability or disposition to resist reporting the response that first comes to mind. However, since the test contains three mathematically based problems, it is possible that the test only measures mathematical abilities, and not cognitive reflection. We found that the models that included an inhibition parameter (i.e., the probability of inhibiting an intuitive response), as well as a mathematical parameter (i.e., the probability of using an adequate mathematical procedure), fitted the data better than a model that only included a mathematical parameter. We also found that the inhibition parameter in males is best explained by both rational thinking ability and the disposition toward actively open-minded thinking, whereas in females this parameter was better explained by rational thinking only. With these findings, this study contributes to the understanding of the processes involved in solving the CRT, and will be particularly useful for researchers who are considering using this test in their research.

A Test Beamline on Diamond Light Source

International Nuclear Information System (INIS)

Sawhney, K. J. S.; Dolbnya, I. P.; Tiwari, M. K.; Alianelli, L.; Scott, S. M.; Preece, G. M.; Pedersen, U. K.; Walton, R. D.

2010-01-01

A Test beamline B16 has been built on the 3 GeV Diamond synchrotron radiation source. The beamline covers a wide photon energy range from 2 to 25 keV. The beamline is highly flexible and versatile in terms of the available beam size (a micron to 100 mm) and the range of energy resolution and photon flux; by virtue of its several operational modes, and the different inter-changeable instruments available in the experiments hutch. Diverse experimental configurations can be flexibly configured using a five-circle diffractometer, a versatile optics test bench, and a suite of detectors. Several experimental techniques including reflectivity, diffraction and imaging are routinely available. Details of the beamline and its measured performance are presented.

Distribution and sources of bioaccumulative air pollutants at Mezquital Valley, Mexico, as reflected by the atmospheric plant Tillandsia recurvata L.

Science.gov (United States)

Zambrano García, A.; Medina Coyotzin, C.; Rojas Amaro, A.; López Veneroni, D.; Martínez, L. Chang; Sosa Iglesias, G.

2009-09-01

Mezquital Valley (MV), a Mexican wastewater-based agricultural and industrial region, is a "hot spot" of regulated air pollutants emissions, but the concurrent unregulated ones, like hazardous metals and polycyclic aromatic hydrocarbons (PAH), remain undocumented. A biomonitoring survey with the epiphytic Tillandsia recurvata was conducted there to detect spatial patterns and potential sources of 20 airborne elements and 15 PAH. The natural δ13C and δ15N ratios of this plant helped in source identification. The regional mean concentration of most elements was two (Cr) to over 40 times (Ni, Pb, V) higher than reported for Tillandsia in other countries. Eleven elements, pyrene and chrysene had 18-214% higher mean concentration at the industrial south than at the agricultural north of MV. The total quantified PAH (mean, 572 ng g-1; range, 143-2568) were composed by medium (65%, phenanthrene to chrysene), low (28%, naphthalene to fluorene) and high molecular weight compounds (7%, Benzo(b)fluoranthene to indeno(1,2,3-cd)pyrene). The δ13C (mean, -14.6‰; range, -15.7‰ to -13.7‰) was consistently lower than -15‰ near the major petroleum combustion sources. The δ15N (mean, -3.0‰; range, -9.9‰ to 3.3‰) varied from positive at agriculture/industrial areas to negative at rural sites. Factor analysis provided a five-factor solution for 74% of the data variance: 1) crustal rocks, 39.5% (Al, Ba, Cu, Fe, Sr, Ti); 2) soils, 11.3%, contrasting contributions from natural (Mg, Mn, Zn) and saline agriculture soils (Na); 3) cement production and fossil fuel combustion, 9.8% (Ca, Ni, V, chrysene, pyrene); 4) probable agricultural biomass burning, 8.1% (K and benzo(g,h,i)perylene), and 5) agriculture with wastewater, 5.2% (δ15N and P). These results indicated high deposition of bioaccumulative air pollutants at MV, especially at the industrial area. Since T. recurvata reflected the regional differences in exposition, it is recommended as a biomonitor for comparisons

Total reflection X-ray photoelectron spectroscopy: A review

International Nuclear Information System (INIS)

Kawai, Jun

2010-01-01

Total reflection X-ray photoelectron spectroscopy (TRXPS) is reviewed and all the published papers on TRXPS until the end of 2009 are included. Special emphasis is on the historical development. Applications are also described for each report. The background reduction is the most important effect of total reflection, but interference effect, relation to inelastic mean free path, change of probing depth are also discussed.

Portable, Fiber-Based, Diffuse Reflection Spectroscopy (DRS) Systems for Estimating Tissue Optical Properties.

Science.gov (United States)

Vishwanath, Karthik; Chang, Kevin; Klein, Daniel; Deng, Yu Feng; Chang, Vivide; Phelps, Janelle E; Ramanujam, Nimmi

2011-02-01

Steady-state diffuse reflection spectroscopy is a well-studied optical technique that can provide a noninvasive and quantitative method for characterizing the absorption and scattering properties of biological tissues. Here, we compare three fiber-based diffuse reflection spectroscopy systems that were assembled to create a light-weight, portable, and robust optical spectrometer that could be easily translated for repeated and reliable use in mobile settings. The three systems were built using a broadband light source and a compact, commercially available spectrograph. We tested two different light sources and two spectrographs (manufactured by two different vendors). The assembled systems were characterized by their signal-to-noise ratios, the source-intensity drifts, and detector linearity. We quantified the performance of these instruments in extracting optical properties from diffuse reflectance spectra in tissue-mimicking liquid phantoms with well-controlled optical absorption and scattering coefficients. We show that all assembled systems were able to extract the optical absorption and scattering properties with errors less than 10%, while providing greater than ten-fold decrease in footprint and cost (relative to a previously well-characterized and widely used commercial system). Finally, we demonstrate the use of these small systems to measure optical biomarkers in vivo in a small-animal model cancer therapy study. We show that optical measurements from the simple portable system provide estimates of tumor oxygen saturation similar to those detected using the commercial system in murine tumor models of head and neck cancer.

From Intensity Profile to Surface Normal: Photometric Stereo for Unknown Light Sources and Isotropic Reflectances.

Science.gov (United States)

Lu, Feng; Matsushita, Yasuyuki; Sato, Imari; Okabe, Takahiro; Sato, Yoichi

2015-10-01

We propose an uncalibrated photometric stereo method that works with general and unknown isotropic reflectances. Our method uses a pixel intensity profile, which is a sequence of radiance intensities recorded at a pixel under unknown varying directional illumination. We show that for general isotropic materials and uniformly distributed light directions, the geodesic distance between intensity profiles is linearly related to the angular difference of their corresponding surface normals, and that the intensity distribution of the intensity profile reveals reflectance properties. Based on these observations, we develop two methods for surface normal estimation; one for a general setting that uses only the recorded intensity profiles, the other for the case where a BRDF database is available while the exact BRDF of the target scene is still unknown. Quantitative and qualitative evaluations are conducted using both synthetic and real-world scenes, which show the state-of-the-art accuracy of smaller than 10 degree without using reference data and 5 degree with reference data for all 100 materials in MERL database.

Primordial condensation of meteorite components - experimental evidence of the state of the source medium

International Nuclear Information System (INIS)

Arrhenius, G.; McCrumb, J.L.; Friedman, N.

1979-01-01

Mineral grains and grain aggregates in meteorites carry potential information on the conditions in the environment where they formed. To avoid model-dependent interpretations it is necessary to develop experimental criteria that uniquely reflect the environmental parameters of interest. These parameters include the various temperatures of the source medium and the temperature of grains at growth all of which are observed to be highly differentiated in the space medium in accordance with the radiation laws. (orig./WL)

Influence of climate on alpine stream chemistry and water sources

Science.gov (United States)

Foks, Sydney; Stets, Edward; Singha, Kamini; Clow, David W.

2018-01-01

The resilience of alpine/subalpine watersheds may be viewed as the resistance of streamflow or stream chemistry to change under varying climatic conditions, which is governed by the relative size (volume) and transit time of surface and subsurface water sources. Here, we use end‐member mixing analysis in Andrews Creek, an alpine stream in Rocky Mountain National Park, Colorado, from water year 1994 to 2015, to explore how the partitioning of water sources and associated hydrologic resilience change in response to climate. Our results indicate that four water sources are significant contributors to Andrews Creek, including snow, rain, soil water, and talus groundwater. Seasonal patterns in source‐water contributions reflected the seasonal hydrologic cycle, which is driven by the accumulation and melting of seasonal snowpack. Flushing of soil water had a large effect on stream chemistry during spring snowmelt, despite making only a small contribution to streamflow volume. Snow had a large influence on stream chemistry as well, contributing large amounts of water with low concentrations of weathering products. Interannual patterns in end‐member contributions reflected responses to drought and wet periods. Moderate and significant correlations exist between annual end‐member contributions and regional‐scale climate indices (the Palmer Drought Severity Index, the Palmer Hydrologic Drought Index, and the Modified Palmer Drought Severity Index). From water year 1994 to 2015, the percent contribution from the talus‐groundwater end member to Andrews Creek increased an average of 0.5% per year (p < 0.0001), whereas the percent contributions from snow plus rain decreased by a similar amount (p = 0.001). Our results show how water and solute sources in alpine environments shift in response to climate variability and highlight the role of talus groundwater and soil water in providing hydrologic resilience to the system.

Measurement of an Evaporating Drop on a Reflective Substrate

Science.gov (United States)

Chao, David F.; Zhang, Nengli

2004-01-01

A figure depicts an apparatus that simultaneously records magnified ordinary top-view video images and laser shadowgraph video images of a sessile drop on a flat, horizontal substrate that can be opaque or translucent and is at least partially specularly reflective. The diameter, contact angle, and rate of evaporation of the drop as functions of time can be calculated from the apparent diameters of the drop in sequences of the images acquired at known time intervals, and the shadowgrams that contain flow patterns indicative of thermocapillary convection (if any) within the drop. These time-dependent parameters and flow patterns are important for understanding the physical processes involved in the spreading and evaporation of drops. The apparatus includes a source of white light and a laser (both omitted from the figure), which are used to form the ordinary image and the shadowgram, respectively. Charge-coupled-device (CCD) camera 1 (with zoom) acquires the ordinary video images, while CCD camera 2 acquires the shadowgrams. With respect to the portion of laser light specularly reflected from the substrate, the drop acts as a plano-convex lens, focusing the laser beam to a shadowgram on the projection screen in front of CCD camera 2. The equations for calculating the diameter, contact angle, and rate of evaporation of the drop are readily derived on the basis of Snell s law of refraction and the geometry of the optics.

See, reflect, learn more: qualitative analysis of breaking bad news reflective narratives.

Science.gov (United States)

Karnieli-Miller, Orit; Palombo, Michal; Meitar, Dafna

2018-05-01

Breaking bad news (BBN) is a challenge that requires multiple professional competencies. BBN teaching often includes didactic and group role-playing sessions. Both are useful and important, but exclude another critical component of students' learning: day-to-day role-model observation in the clinics. Given the importance of observation and the potential benefit of reflective writing in teaching, we have incorporated reflective writing into our BBN course. The aim of this study was to enhance our understanding of the learning potential in reflective writing about BBN encounters and the ability to identify components that inhibit this learning. This was a systematic qualitative immersion/crystallization analysis of 166 randomly selected BBN narratives written by 83 senior medical students. We analysed the narratives in an iterative consensus-building process to identify the issues discussed, the lessons learned and the enhanced understanding of BBN. Having previously been unaware of, not invited to or having avoided BBN encounters, the mandatory assignment led students to search for or ask their mentors to join them in BBN encounters. Observation and reflective writing enhanced students' awareness that 'bad news' is relative and subjective, while shedding light on patients', families', physicians' and their own experiences and needs, revealing the importance of the different components of the BBN protocol. We identified diversity among the narratives and the extent of students' learning. Narrative writing provided students with an opportunity for a deliberative learning process. This led to deeper understanding of BBN encounters, of how to apply the newly taught protocol, or of the need for it. This process connected the formal and informal or hidden curricula. To maximise learning through reflective writing, students should be encouraged to write in detail about a recent observed encounter, analyse it according to the protocol, address different participants

System and method for determination of the reflection wavelength of multiple low-reflectivity bragg gratings in a sensing optical fiber

Science.gov (United States)

Moore, Jason P. (Inventor)

2009-01-01

A system and method for determining a reflection wavelength of multiple Bragg gratings in a sensing optical fiber comprise: (1) a source laser; (2) an optical detector configured to detect a reflected signal from the sensing optical fiber; (3) a plurality of frequency generators configured to generate a signal having a frequency corresponding to an interferometer frequency of a different one of the plurality of Bragg gratings; (4) a plurality of demodulation elements, each demodulation element configured to combine the signal produced by a different one of the plurality of frequency generators with the detected signal from the sensing optical fiber; (5) a plurality of peak detectors, each peak detector configured to detect a peak of the combined signal from a different one of the demodulation elements; and (6) a laser wavenumber detection element configured to determine a wavenumber of the laser when any of the peak detectors detects a peak.

A cryogenic thermal source for detector array characterization

Science.gov (United States)

Chuss, David T.; Rostem, Karwan; Wollack, Edward J.; Berman, Leah; Colazo, Felipe; DeGeorge, Martin; Helson, Kyle; Sagliocca, Marco

2017-10-01

We describe the design, fabrication, and validation of a cryogenically compatible quasioptical thermal source for characterization of detector arrays. The source is constructed using a graphite-loaded epoxy mixture that is molded into a tiled pyramidal structure. The mold is fabricated using a hardened steel template produced via a wire electron discharge machining process. The absorptive mixture is bonded to a copper backplate enabling thermalization of the entire structure and measurement of the source temperature. Measurements indicate that the reflectance of the source is <0.001 across a spectral band extending from 75 to 330 GHz.

Ion Dynamics at Shocks: Ion Reflection and Beam Formation at Quasi-perpendicular Shocks

International Nuclear Information System (INIS)

Kucharek, Harald; Moebius, Eberhard

2005-01-01

The physics of collisionless shocks is controlled by the ion dynamics. The generation of gyrating ions by reflection as well as the formation of field-aligned ion beams are essential parts of this dynamic. On the one hand reflection is most likely the first interaction of ions with the shock before they undergo the downstream thermalization process. On the other hand field-aligned ion beams, predominately found at the quasi-perpendicular bow shock, propagate into the distant foreshock region and may create wave activity. We revisit ion reflection, the source and basic production mechanism of field-aligned ion beams, by using multi-spacecraft measurements and contrast these observations with existing theories. Finally, we propose an alternative production mechanism

How to reduce scientific irreproducibility: the 5-year reflection.

Science.gov (United States)

Fiala, Clare; Diamandis, Eleftherios P

2017-10-26

We discuss in depth six causes of scientific irreproducibility and their ramifications for the clinical sciences: fraud, unfounded papers published by prominent authorities, bias, technical deficiencies, fragmented science and problems with big data. Some proposed methods to combat this problem are briefly described, including an effort to replicate results from some high impact papers and a proposal that authors include detailed preclinical data in papers with supposedly high translational value. We here advocate for a 5-year reflection on papers with seemingly high clinical/translational potential, published alongside the original paper where authors reflect on the quality, reproducibility and impact of their findings. These reflections can be used as a benchmark for credibility, and begin a virtuous cycle of improving the quality of published findings in the literature.

Reconstruction of MODIS Spectral Reflectance under Cloudy-Sky Condition

Directory of Open Access Journals (Sweden)

Bo Gao

2016-09-01

Full Text Available Clouds usually cause invalid observations for sensors aboard satellites, which corrupts the spatio-temporal continuity of land surface parameters retrieved from remote sensing data (e.g., MODerate Resolution Imaging Spectroradiometer (MODIS data and prevents the fusing of multi-source remote sensing data in the field of quantitative remote sensing. Based on the requirements of spatio-temporal continuity and the necessity of methods to restore bad pixels, primarily resulting from image processing, this study developed a novel method to derive the spectral reflectance for MODIS band of cloudy pixels in the visual–near infrared (VIS–NIR spectral channel based on the Bidirectional Reflectance Distribution Function (BRDF and multi-spatio-temporal observations. The proposed method first constructs the spatial distribution of land surface reflectance based on the corresponding BRDF and the solar-viewing geometry; then, a geographically weighted regression (GWR is introduced to individually derive the spectral surface reflectance for MODIS band of cloudy pixels. A validation of the proposed method shows that a total root-mean-square error (RMSE of less than 6% and a total R2 of more than 90% are detected, which indicates considerably better precision than those exhibited by other existing methods. Further validation of the retrieved white-sky albedo based on the spectral reflectance for MODIS band of cloudy pixels confirms an RMSE of 3.6% and a bias of 2.2%, demonstrating very high accuracy of the proposed method.

Analysis of Smith-Purcell BWO with end reflections

International Nuclear Information System (INIS)

Kumar, V.; Kim, K.-J.

2006-01-01

We present a one-dimensional time-dependent analysis and simulation of Smith-Purcell (SP) backward wave oscillator (BWO) taking end reflections and attenuation into account. In the linear regime, we obtain an analytic solution and calculate the start current. The dependence of start current on end reflections is studied taking the attenuation due to finite conductivity into account. In this paper, we have set up Maxwell-Lorentz equations for the one-dimensional time-dependent analysis of SP-BWO including end reflection and attenuation due to finite conductivity. We have obtained a solution in the linear regime and extended the analysis to the nonlinear regime by solving the Maxwell-Lorentz equations numerically. Our analysis can be used for detailed optimization of outcoupled power and start current in SP-BWO taking end reflection and attenuation into account.

GREEN PRICES – A REFLECTION OF ENVIRONMETAL PROTECTION

Directory of Open Access Journals (Sweden)

Daniela SIMTION

2014-10-01

Full Text Available The price is generally a very important factor in taking the purchase decision; it will influence the acceptance or rejection of organic products. For those who believe market forces represent a path to sustainability, it is vital to include eco-costs in the product costs and, further, in their prices. Otherwise, consumption growth will result in a continuous degradation of ecosystems, taking into consideration that environmental costs are not reflected in the price. To what extent a company is considering the ecological policy will be reflected in its cost structure. Organic products, most of the times, will incur additional costs generated by preservation and improvement expenses for environmental. These expenses will be reflected in costs, the price will reflect the value of the main benefits required by the consumer.

Excitation of anodized alumina films with a light source

DEFF Research Database (Denmark)

Aggerbeck, Martin; Canulescu, Stela; Rechendorff, K.

Optical properties of anodized aluminium alloys were determined by optical diffuse reflectance spectroscopy of such films. Samples with different concentrations of dopants were excited with a white-light source combined with an integrating sphere for fast determination of diffuse reflectance....... The UV-VIS reflectance of Ti-doped anodized aluminium films was measured over the wavelength range of 200 nm to 900 nm. Titanium doped-anodized aluminium films with 5-15 wt% Ti were characterized. Changes in the diffuse light scattering of doped anodized aluminium films, and thus optical appearance......, with doping are discussed. Using the Kubelka-Munk model on the diffuse reflectance spectra of such films, the bandgap Eg of the oxide alloys can be determined....

Global sourcing - performance and integration : reflections on performance, implications from cross-functional and external integration

NARCIS (Netherlands)

Horn, Philipp

2013-01-01

Despite the fact that firms and individuals have been sourcing on a global basis since ancient times, global sourcing as a topic has received considerable attention from managers and scholars in recent years. Global business has been reported to be growing considerably during the last decades and

Peer group reflection helps clinical teachers to critically reflect on their teaching.

Science.gov (United States)

Boerboom, Tobias B B; Jaarsma, Debbie; Dolmans, Diana H J M; Scherpbier, Albert J J A; Mastenbroek, Nicole J J M; Van Beukelen, Peter

2011-01-01

Student evaluations can help clinical teachers to reflect on their teaching skills and find ways to improve their teaching. Studies have shown that the mere presentation of student evaluations is not a sufficient incentive for teachers to critically reflect on their teaching. We evaluated and compared the effectiveness of two feedback facilitation strategies that were identical except for a peer reflection meeting. In this study, 54 clinical teachers were randomly assigned to two feedback strategies. In one strategy, a peer reflection was added as an additional step. All teachers completed a questionnaire evaluating the strategy that they had experienced. We analysed the reflection reports and the evaluation questionnaire. Both strategies stimulated teachers to reflect on feedback and formulate alternative actions for their teaching practice. The teachers who had participated in the peer reflection meeting showed deeper critical reflection and more concrete plans to change their teaching. All feedback strategies were considered effective by the majority of the teachers. Strategies with student feedback and self-assessment stimulated reflection on teaching and helped clinical teachers to formulate plans for improvement. A peer reflection meeting seemed to enhance reflection quality. Further research should establish whether it can have lasting effects on teaching quality.

Adaptive infrared-reflecting systems inspired by cephalopods

Science.gov (United States)

Xu, Chengyi; Stiubianu, George T.; Gorodetsky, Alon A.

2018-03-01

Materials and systems that statically reflect radiation in the infrared region of the electromagnetic spectrum underpin the performance of many entrenched technologies, including building insulation, energy-conserving windows, spacecraft components, electronics shielding, container packaging, protective clothing, and camouflage platforms. The development of their adaptive variants, in which the infrared-reflecting properties dynamically change in response to external stimuli, has emerged as an important unmet scientific challenge. By drawing inspiration from cephalopod skin, we developed adaptive infrared-reflecting platforms that feature a simple actuation mechanism, low working temperature, tunable spectral range, weak angular dependence, fast response, stability to repeated cycling, amenability to patterning and multiplexing, autonomous operation, robust mechanical properties, and straightforward manufacturability. Our findings may open opportunities for infrared camouflage and other technologies that regulate infrared radiation.

Pigments which reflect infrared radiation from fire

Science.gov (United States)

Berdahl, Paul H.

1998-01-01

Conventional paints transmit or absorb most of the intense infrared (IR) radiation emitted by fire, causing them to contribute to the spread of fire. The present invention comprises a fire retardant paint additive that reflects the thermal IR radiation emitted by fire in the 1 to 20 micrometer (.mu.m) wavelength range. The important spectral ranges for fire control are typically about 1 to about 8 .mu.m or, for cool smoky fires, about 2 .mu.m to about 16 .mu.m. The improved inventive coatings reflect adverse electromagnetic energy and slow the spread of fire. Specific IR reflective pigments include titanium dioxide (rutile) and red iron oxide pigments with diameters of about 1 .mu.m to about 2 .mu.m and thin leafing aluminum flake pigments.

Reflections on researching rape resistance.

Science.gov (United States)

Ullman, Sarah E

2014-03-01

This article provides a retrospective account of my experience embarking on research about women's resistance to rape, including reflections on personal and professional experiences related to studying this topic. I discuss factors inspiring my interest, including pioneering feminist rape researchers, my experience as a woman living with the reality and fear of rape, and influential mentors who facilitated my career development as a scholar in graduate school and beyond. I weave this narrative together with my thoughts about how the study of resistance relates to other important issues in the field of sexual assault including alcohol, recovery, and prevention.

Media for Reflection

DEFF Research Database (Denmark)

Knudsen, Morten

2016-01-01

This article develops the concept media for reflection in the interest of conceptualizing the interpretative frames that enable and limit reflection in management and leadership education. The concept ‘media for reflection’ allows us to conceptualize the social and cultural mediation of reflection...... without reducing reflection to an effect of the social structures and cultural norms in which it is embedded. Based on the developed theoretical framework, this article analyses how a renaissance ‘mirror for princes’ and contemporary research-based management education mediate reflection. The content...... of the mediations is analysed as well as the societal and organizational background. Furthermore, the means by which the two media enable and limit reflection in different ways is compared. Finally, the article discusses possible implications of the analysis in terms of management and leadership education....

Ethical reflection and psychotherapy.

Science.gov (United States)

Vyskocilová, Jana; Prasko, Jan

2013-01-01

Theories of ethics and ethical reflection may be applied to both theory and practice in psychotherapy. There is a natural affinity between ethics and psychotherapy. Psychotherapy practice is concerned with human problems, dilemmas and emotions related to both one's own and other people's values. Ethics is also concerned with dilemmas in human thinking and with how these dilemmas reflect other individuals' values. Philosophical reflection itself is not a sufficient basis for the ethics of psychotherapy but it may aid in exploring attitudes related to psychotherapy, psychiatry and health care. PubMed, Web of Science and Scopus databases were searched for articles containing the keywords "psychotherapy", "ethics", "therapeutic relationship" and "supervision". The search was conducted by repeating the terms in various combinations without language or time restrictions. Also included were data from monographs cited in reviews. The resulting text is a review with conclusions concerning ethical aspects of psychotherapy. The ability to behave altruistically, sense for justice and reciprocity and mutual help are likely to be genetically determined as dispositions to be later developed by upbringing or to be formed or deformed by upbringing. Early experiences lead to formation of ethical attitudes which are internalized and then applied to both one's own and other people's behavior. Altruistic behavior has a strong impact on an individual's health and its acceptance may positively influence the pathophysiological mechanisms underlying numerous diseases. Ethical theory and reflection, however, may be applied to both theory and practice of psychotherapy in a conscious, targeted and thoughtful manner. In everyday practice, psychotherapists and organizations must necessarily deal with conscious conflicts between therapeutic possibilities, clients' wishes, their own as well as clients' ideas and the real world. Understanding one's own motives in therapy is one of the aims of a

Seismic and electromagnetic interferometry : Retrieval of the earth's reflection response using crosscorrelation

NARCIS (Netherlands)

Draganov, D.

2007-01-01

One of the goals of exploration geophysics is to obtain an image of the subsurface. In petroleum exploration and near-surface geophysics, this is best achieved using reflected waves. For this, a controlled seismic or electromagnetic source is placed at the surface, activated, and the wavefields that

Do Staphylococcus epidermidis Genetic Clusters Predict Isolation Sources?

Science.gov (United States)

Tolo, Isaiah; Thomas, Jonathan C.; Fischer, Rebecca S. B.; Brown, Eric L.; Gray, Barry M.

2016-01-01

Staphylococcus epidermidis is a ubiquitous colonizer of human skin and a common cause of medical device-associated infections. The extent to which the population genetic structure of S. epidermidis distinguishes commensal from pathogenic isolates is unclear. Previously, Bayesian clustering of 437 multilocus sequence types (STs) in the international database revealed a population structure of six genetic clusters (GCs) that may reflect the species' ecology. Here, we first verified the presence of six GCs, including two (GC3 and GC5) with significant admixture, in an updated database of 578 STs. Next, a single nucleotide polymorphism (SNP) assay was developed that accurately assigned 545 (94%) of 578 STs to GCs. Finally, the hypothesis that GCs could distinguish isolation sources was tested by SNP typing and GC assignment of 154 isolates from hospital patients with bacteremia and those with blood culture contaminants and from nonhospital carriage. GC5 was isolated almost exclusively from hospital sources. GC1 and GC6 were isolated from all sources but were overrepresented in isolates from nonhospital and infection sources, respectively. GC2, GC3, and GC4 were relatively rare in this collection. No association was detected between fdh-positive isolates (GC2 and GC4) and nonhospital sources. Using a machine learning algorithm, GCs predicted hospital and nonhospital sources with 80% accuracy and predicted infection and contaminant sources with 45% accuracy, which was comparable to the results seen with a combination of five genetic markers (icaA, IS256, sesD [bhp], mecA, and arginine catabolic mobile element [ACME]). Thus, analysis of population structure with subgenomic data shows the distinction of hospital and nonhospital sources and the near-inseparability of sources within a hospital. PMID:27076664

Seismic explosion sources on an ice cap

DEFF Research Database (Denmark)

Shulgin, Alexey; Thybo, Hans

2015-01-01

crustal model can be modelled. A crucial challenge for applying the technique is to control the sources. Here, we present data that describe the efficiency of explosive sources in the ice cover. Analysis of the data shows, that the ice cap traps a significant amount of energy, which is observed......Controlled source seismic investigation of crustal structure below ice covers is an emerging technique. We have recently conducted an explosive refraction/wide-angle reflection seismic experiment on the ice cap in east-central Greenland. The data-quality is high for all shot points and a full...

Reflectance Confocal Microscopy in Lentigo Maligna.

Science.gov (United States)

Gamo, R; Pampín, A; Floristán, U

2016-12-01

Lentigo maligna is the most common type of facial melanoma. Diagnosis is complicated, however, as it shares clinical and dermoscopic characteristics with other cutaneous lesions of the face. Reflectance confocal microscopy is an imaging technique that permits the visualization of characteristic features of lentigo maligna. These include a disrupted honeycomb pattern and pagetoid cells with a tendency to show folliculotropism. These cells typically have a dendritic morphology, although they may also appear as round cells measuring over 20μm with atypical nuclei. Poorly defined dermal papillae and atypical cells may be seen at the dermal-epidermal junction and can form bridges resembling mitochondrial structures. Other characteristic findings include junctional swelling with atypical cells located around the follicles, resembling caput medusae. Reflectance confocal microscopy is a very useful tool for diagnosing lentigo maligna. Copyright © 2016 AEDV. Publicado por Elsevier España, S.L.U. All rights reserved.

Beyond the Margins: Reflective Writing and Development of Reflective Capacity in Medical Education

Science.gov (United States)

Reis, Shmuel P.

2010-01-01

Reflective capacity has been described as an essential characteristic of professionally competent clinical practice, core to ACGME competencies. Reflection has been recently linked to promoting effective use of feedback in medical education and associated with improved diagnostic accuracy, suggesting promising outcomes. There has been a proliferation of reflective writing pedagogy within medical education to foster development of reflective capacity, extend empathy with deepened understanding of patients’ experience of illness, and promote practitioner well-being. At Alpert Med, “interactive” reflective writing with guided individualized feedback from interdisciplinary faculty to students’ reflective writing has been implemented in a Doctoring course and Family Medicine clerkship as an educational method to achieve these aims. Such initiatives, however, raise fundamental questions of reflection definition, program design, efficacy of methods, and outcomes assessment. Within this article, we consider opportunities and challenges associated with implementation of reflective writing curricula for promotion of reflective capacity within medical education. We reflect upon reflection. PMID:20407840

The sources of Gessner's pictures for the Historia animalium.

Science.gov (United States)

Kusukawa, S

2010-07-01

Gessner's sources for the pictures in his Historia animalium were varied in kind and in quality. This should be understood within the larger context of the Historia animalium in which Gessner sought to collect everything ever written about animals, an enterprise that could not be completed by a single individual. Just as Gessner did not distil or reduce similar texts but retained these as well as contradictory or false textual descriptions as part of a repository of knowledge, so also Gessner included several pictures of the same animal, false or badly drawn ones, and juxtaposed erroneous and 'true' images. The attribution of images to witnesses and correspondences also reflects Gessner's strategy to credit those who drew his attention to new information first. The sources of Gessner's images thus indicate how his visual world encompassed more than the strictly self-observable, and a pictorial practice that was intimately connected with textual traditions and intellectual networks.

Analysis of the Structure Ratios of the Funding Sources

Directory of Open Access Journals (Sweden)

Maria Daniela Bondoc

2014-06-01

Full Text Available The funding sources of the assets and liabilities in the balance sheet include equity capitals and the debts of the entity. The analysis of the structure rates of the funding sources allows for making assessments related to the funding policy, highlighting the financial autonomy and how resources are provided. Using the literature specializing in economic and financial analysis, this paper aims at presenting these rates that focus, on the one hand, to reflect the degree of financial dependence (the rate of financial stability, the rate of global financial autonomy, the rate of on-term financial autonomy and on the other hand the debt structure (the rate of short-term debts, the global indebtedness rate, the on-term indebtedness rate. Based on the financial statements of an entity in the Argeş County, I analysed these indicators, and I drew conclusions and made assessments related to the autonomy, indebtedness and financial stability of the studied entity.

Density, ultrasound velocity, acoustic impedance, reflection and absorption coefficient determination of liquids via multiple reflection method.

Science.gov (United States)

Hoche, S; Hussein, M A; Becker, T

2015-03-01

The accuracy of density, reflection coefficient, and acoustic impedance determination via multiple reflection method was validated experimentally. The ternary system water-maltose-ethanol was used to execute a systematic, temperature dependent study over a wide range of densities and viscosities aiming an application as inline sensor in beverage industries. The validation results of the presented method and setup show root mean square errors of: 1.201E-3 g cm(-3) (±0.12%) density, 0.515E-3 (0.15%) reflection coefficient and 1.851E+3 kg s(-1) m(-2) (0.12%) specific acoustic impedance. The results of the diffraction corrected absorption showed an average standard deviation of only 0.12%. It was found that the absorption change shows a good correlation to concentration variations and may be useful for laboratory analysis of sufficiently pure liquids. The main part of the observed errors can be explained by the observed noise, temperature variation and the low signal resolution of 50 MHz. In particular, the poor signal-to-noise ratio of the second reflector echo was found to be a main accuracy limitation. Concerning the investigation of liquids the unstable properties of the reference material PMMA, due to hygroscopicity, were identified to be an additional, unpredictable source of uncertainty. While dimensional changes can be considered by adequate methodology, the impact of the time and temperature dependent water absorption on relevant reference properties like the buffer's sound velocity and density could not be considered and may explain part of the observed deviations. Copyright © 2014 Elsevier B.V. All rights reserved.

Source-system windowing for speech analysis

NARCIS (Netherlands)

Yegnanarayana, B.; Satyanarayana Murthy, P.; Eggen, J.H.

1993-01-01

In this paper we propose a speech-analysis method to bring out characteristics of the vocal tract system in short segments which are much less than a pitch period. The method performs windowing in the source and system components of the speech signal and recombines them to obtain a signal reflecting

TESTING RELATIVISTIC REFLECTION AND RESOLVING OUTFLOWS IN PG 1211+143 WITH XMM-NEWTON AND NuSTAR

Energy Technology Data Exchange (ETDEWEB)

Lobban, A. P.; Pounds, K.; Vaughan, S. [University of Leicester, Department of Physics and Astronomy, University Road, Leicester LE1 7RH (United Kingdom); Reeves, J. N., E-mail: al394@le.ac.uk [Astrophysics Group, Keele University, Staffordshire, ST5 5BG (United Kingdom)

2016-11-10

We analyze the broad-band X-ray spectrum (0.3–50 keV) of the luminous Seyfert 1/quasar PG 1211+143—the archetypal source for high-velocity X-ray outflows—using near-simultaneous XMM-Newton and NuSTAR observations. We compare pure relativistic reflection models with a model including the strong imprint of photoionized emission and absorption from a high-velocity wind, finding a spectral fit that extrapolates well over the higher photon energies covered by NuSTAR . Inclusion of the high signal-to-noise ratio XMM-Newton spectrum provides much tighter constraints on the model parameters, with a much harder photon index/lower reflection fraction compared to that from the NuSTAR data alone. We show that pure relativistic reflection models are not able to account for the spectral complexity of PG 1211+143 and that wind absorption models are strongly required to match the data in both the soft X-ray and Fe K spectral regions. In confirming the significance of previously reported ionized absorption features, the new analysis provides a further demonstration of the power of combining the high throughput and resolution of long-look XMM-Newton observations with the unprecedented spectral coverage of NuSTAR .

Enabling self-reflection with LifelogExplorer : generating simple views from complex data

NARCIS (Netherlands)

Kocielnik, R.D.; Maggi, F.M.; Sidorova, N.

2013-01-01

Nowadays, people are overwhelmed with multiple tasks and responsibilities, resulting in increasing stress level. At the same time, it becomes harder to find time for self-reflection and diagnostics of problems that can be source of stress. In this paper, we propose a tool that supports a person in

Newly graduated nurses' use of knowledge sources in clinical decision-making

DEFF Research Database (Denmark)

Voldbjerg, Siri Lygum; Grønkjaer, Mette; Wiechula, Rick

2017-01-01

AIMS AND OBJECTIVES: To explore which knowledge sources newly graduated nurses' use in clinical decision-making and why and how they are used. BACKGROUND: In spite of an increased educational focus on skills and competencies within evidence based practice newly graduated nurses' ability to use...... approaches to strengthen the knowledgebase used in clinical decision-making. DESIGN AND METHODS: Ethnographic study using participant-observation and individual semi-structured interviews of nine Danish newly graduated nurses in medical and surgical hospital settings. RESULTS: Newly graduates use...... in clinical decision-making. If newly graduates are to be supported in an articulate and reflective use of a variety of sources, they have to be allocated to experienced nurses who model a reflective, articulate and balanced use of knowledge sources. This article is protected by copyright. All rights reserved....

Plasmonically Enhanced Reflectance of Heat Radiation from Low-Bandgap Semiconductor Microinclusions.

Science.gov (United States)

Tang, Janika; Thakore, Vaibhav; Ala-Nissila, Tapio

2017-07-18

Increased reflectance from the inclusion of highly scattering particles at low volume fractions in an insulating dielectric offers a promising way to reduce radiative thermal losses at high temperatures. Here, we investigate plasmonic resonance driven enhanced scattering from microinclusions of low-bandgap semiconductors (InP, Si, Ge, PbS, InAs and Te) in an insulating composite to tailor its infrared reflectance for minimizing thermal losses from radiative transfer. To this end, we compute the spectral properties of the microcomposites using Monte Carlo modeling and compare them with results from Fresnel equations. The role of particle size-dependent Mie scattering and absorption efficiencies, and, scattering anisotropy are studied to identify the optimal microinclusion size and material parameters for maximizing the reflectance of the thermal radiation. For composites with Si and Ge microinclusions we obtain reflectance efficiencies of 57-65% for the incident blackbody radiation from sources at temperatures in the range 400-1600 °C. Furthermore, we observe a broadbanding of the reflectance spectra from the plasmonic resonances due to charge carriers generated from defect states within the semiconductor bandgap. Our results thus open up the possibility of developing efficient high-temperature thermal insulators through use of the low-bandgap semiconductor microinclusions in insulating dielectrics.

Surface-water nutrient conditions and sources in the United States Pacific Northwest

Science.gov (United States)

Wise, D.R.; Johnson, H.M.

2011-01-01

The SPAtially Referenced Regressions On Watershed attributes (SPARROW) model was used to perform an assessment of surface-water nutrient conditions and to identify important nutrient sources in watersheds of the Pacific Northwest region of the United States (U.S.) for the year 2002. Our models included variables representing nutrient sources as well as landscape characteristics that affect nutrient delivery to streams. Annual nutrient yields were higher in watersheds on the wetter, west side of the Cascade Range compared to watersheds on the drier, east side. High nutrient enrichment (relative to the U.S. Environmental Protection Agency's recommended nutrient criteria) was estimated in watersheds throughout the region. Forest land was generally the largest source of total nitrogen stream load and geologic material was generally the largest source of total phosphorus stream load generated within the 12,039 modeled watersheds. These results reflected the prevalence of these two natural sources and the low input from other nutrient sources across the region. However, the combined input from agriculture, point sources, and developed land, rather than natural nutrient sources, was responsible for most of the nutrient load discharged from many of the largest watersheds. Our results provided an understanding of the regional patterns in surface-water nutrient conditions and should be useful to environmental managers in future water-quality planning efforts.

A status report on the Advanced Neutron Source project

International Nuclear Information System (INIS)

West, C.D.

1993-01-01

The Advanced Neutron Source (ANS) will be a new laboratory for neutron research, centered around a 330 MW(f) research reactor cooled and reflected by heavy water and including extensive experiment systems and support facilities. The major components of the baseline design, occupying about 16 heetares, are a guide hall/research support area, containing most of the neutron beam experiment systems, shops and supporting laboratories; a 60 m diameter containment building housing the reactor and its pimary coolant system, and selected scientific research facilities; an operations support building with the majority of the remaining plant systems, an office/interface complex providing a carefully designed, user friendly entry point for access control; and several other major facilities including user housing, an electrical substation, a diesel generator building, a cryorefrigerator building, and heavy water cleanup and upgrade systems

Investigating murals with terahertz reflective tomography

Science.gov (United States)

Yuan, Minjie; Sun, Wenfeng; Wang, Xinke; Wang, Sen; Zhang, Qunxi; Ye, Jiasheng; Zhang, Yan

2015-08-01

Terahertz time-domain spectroscopy (THz-TDS) imaging technology has been proposed to be used in the non-invasive detection of murals. THz-TDS images provide structural data of the sample that cannot be obtained with other complementary techniques. In this paper, two types of defects hidden in the plaster used to simulate the cases of defects in the murals, have been investigated by the terahertz reflected time domain spectroscopy imaging system. These preset defects include a leaf slice and a slit built in the plaster. With the terahertz reflective tomography, information about defects has been determined involving the thickness from the surface of sample to the built-in defect, the profile and distribution of the defect. With this THz tomography, different defects with the changes of optical thickness and their relative refractive index have been identified. The application of reflective pulsed terahertz imaging has been extended to the defect detection of the murals.

Reflection groups

International Nuclear Information System (INIS)

Eggermont, G.

2006-01-01

In 2005, PISA organised proactive meetings of reflection groups on involvement in decision making, expert culture and ethical aspects of radiation protection.All reflection group meetings address particular targeted audiences while the output publication in book form is put forward

[Around biological evolution. Reflections of a physicist].

Science.gov (United States)

Sanchez-Palencia, Evariste

2016-01-01

This text is the written version of a talk at the Société de Biologie on February 17, 2016. It contains reflections of a non-biologist scientist on general problems of biological evolution, including the kind of causality involved, the ideas emerging from it, in particular the constructive and structuring character of phenomena such as predation, the role of stability and attractors. This leads to a larger reflection on dialectics, the general framework of evolving processes, which overpasses formal logic and instantaneousness. © Société de Biologie, 2016.

Release path temperatures of shock-compressed tin from dynamic reflectance and radiance measurements

Energy Technology Data Exchange (ETDEWEB)

La Lone, B. M., E-mail: lalonebm@nv.doe.gov; Stevens, G. D.; Turley, W. D. [National Security Technologies, LLC, Special Technologies Laboratory, Santa Barbara, California 93111 (United States); Holtkamp, D. B. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); Iverson, A. J. [National Security Technologies, LLC, Los Alamos Operations, Los Alamos, New Mexico 87544 (United States); Hixson, R. S.; Veeser, L. R. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States); National Security Technologies, LLC, Los Alamos Operations, Los Alamos, New Mexico 87544 (United States)

2013-08-14

Dynamic reflectance and radiance measurements were conducted for tin samples shock compressed to 35 GPa and released to 15 GPa using high explosives. We determined the reflectance of the tin samples glued to lithium fluoride windows using an integrating sphere with an internal xenon flashlamp as an illumination source. The dynamic reflectance (R) was determined at near normal incidence in four spectral bands with coverage in visible and near-infrared spectra. Uncertainties in R/R{sub 0} are <2%, and uncertainties in absolute reflectance are <5%. In complementary experiments, thermal radiance from the tin/glue/lithium fluoride interface was recorded with similar shock stress and spectral coverage as the reflectance measurements. The two sets of experiments were combined to obtain the temperature history of the tin surface with an uncertainty of <2%. The stress at the interface was determined from photonic Doppler velocimetry and combined with the temperatures to obtain temperature-stress release paths for tin. We discuss the relationship between the experimental release paths and release isentropes that begin on the principal shock Hugoniot.

Active multispectral reflection fingerprinting of persistent chemical agents

Science.gov (United States)

Tholl, H. D.; Münzhuber, F.; Kunz, J.; Raab, M.; Rattunde, M.; Hugger, S.; Gutty, F.; Grisard, A.; Larat, C.; Papillon, D.; Schwarz, M.; Lallier, E.; Kastek, M.; Piatkowski, T.; Brygo, F.; Awanzino, C.; Wilsenack, F.; Lorenzen, A.

2017-10-01

Remote detection of toxic chemicals of very low vapour pressure deposited on surfaces in form of liquid films, droplets or powder is a capability that is needed to protect operators and equipment in chemical warfare scenarios and in industrial environments. Infrared spectroscopy is a suitable means to support this requirement. Available instruments based on passive emission spectroscopy have difficulties in discriminating the infrared emission spectrum of the surface background from that of the contamination. Separation of background and contamination is eased by illuminating the surface with a spectrally tune-able light source and by analyzing the reflectivity spectrum. The project AMURFOCAL (Active Multispectral Reflection Fingerprinting of Persistent Chemical Agents) has the research topic of stand-off detection and identification of chemical warfare agents (CWAs) with amplified quantum cascade laser technology in the long-wave infrared spectral range. The project was conducted under the Joint Investment Programme (JIP) on CBRN protection funded through the European Defence Agency (EDA). The AMURFOCAL instrument comprises a spectrally narrow tune-able light source with a broadband infrared detector and chemometric data analysis software. The light source combines an external cavity quantum cascade laser (EC-QCL) with an optical parametric amplifier (OPA) to boost the peak output power of a short laser pulse tune-able over the infrared fingerprint region. The laser beam is focused onto a target at a distance between 10 and 20 m. A 3D data cube is registered by tuning the wavelength of the laser emission while recording the received signal scattered off the target using a multi-element infrared detector. A particular chemical is identified through the extraction of its characteristic spectral fingerprint out of the measured data. The paper describes the AMURFOCAL instrument, its functional units, and its principles of operation.

Crustal structure in the Kiruna area, northern Sweden, based on seismic reflection profiling

Science.gov (United States)

Juhojuntti, Niklas; Bergman, Stefan; Olsson, Sverker

2013-04-01

Northernmost Sweden is currently one of the most active mining areas in Europe. In order to better understand the regional three-dimensional crustal structure and to support deep ore exploration, we have acquired a 74 km long seismic reflection profile in the Kiruna area. The upper crust in this area is largely composed of various supracrustal units, which are dominated by metabasalts, acidic metavolcanics and clastic metasedimentary rocks, resting on an Archaean metagranitoid complex. All of these units have been intruded by plutonic rocks, and to variable degrees folded, sheared and metamorphosed, during the Svecokarelian orogeny. The profile crosses several steep ductile shear zones, some of which extend for hundreds of kilometres along strike. Many of the lithological contacts and deformation zones are expected to be seismically reflective. The profile is located only a few kilometres from the world's largest underground iron-ore mine in Kiruna, and closer to the profile there are several known ore bodies, some of which are active exploration targets. For the seismic recording we used approximately 350 geophones in split-spread configuration, at a separation of 25 m. The main seismic source was the Vibsist system (an impact source), which normally was employed at every geophone station. We also fired explosive charges (8-16 kg) at a few locations distributed along the profile to image deeper structures, although at very low resolution. Wireless seismometers were placed along and to the side of the profile, mainly in order to achieve better velocity control and to study out-of-the-plane reflections. Some mining blasts in Kiruna were also recorded. The upper crust in the area is quite reflective, most clearly demonstrated by the dynamite shot records. Some of the reflections appear to originate from steeply dipping structures. The dynamite shot records show a set of reflections at 3-4 s twt, corresponding to a depth of roughly 10 km, the explanation for which is

High gain durable anti-reflective coating

Energy Technology Data Exchange (ETDEWEB)

Maghsoodi, Sina; Brophy, Brenor L.; Colson, Thomas E.; Gonsalves, Peter R.; Abrams, Ze' ev R.

2017-06-27

Disclosed herein are polysilsesquioxane-based anti-reflective coating (ARC) compositions, methods of preparation, and methods of deposition on a substrate. In one embodiment, the polysilsesquioxane of this disclosure is prepared in a two-step process of acid catalyzed hydrolysis of organoalkoxysilane followed by addition of tetralkoxysilane that generates silicone polymers with >40 mol % silanol based on Si-NMR. These high silanol siloxane polymers are stable and have a long shelf-life in polar organic solvents at room temperature. Also disclosed are low refractive index ARC made from these compositions with and without additives such as porogens, templates, thermal radical initiator, photo radical initiators, crosslinkers, Si--OH condensation catalyst and nano-fillers. Also disclosed are methods and apparatus for applying coatings to flat substrates including substrate pre-treatment processes, coating processes and coating curing processes including skin-curing using hot-air knives. Also disclosed are coating compositions and formulations for highly tunable, durable, highly abrasion-resistant functionalized anti-reflective coatings.

Reflective journaling and development of cultural humility in students.

Science.gov (United States)

Schuessler, Jenny B; Wilder, Barbara; Byrd, Linda W

2012-01-01

Cultural humility requires self-evaluation and the awareness that one's own culture is not the only or best one. Teaching health care providers to become culturally humble includes the development of critical thinking skills and the ability to reflect on practice. Journaling as a teaching strategy helps students develop these skills. This article describes the use of reflective journaling as students progressed through four semesters of a community clinical experience. This qualitative, descriptive study was based on the principles of naturalistic inquiry with person-centered written reflections.Two hundred journal entries from 50 students were reviewed, and II themes were identified. Cultural humility cannot be learned merely in the classroom with traditional teaching methods. Reflection on experiences over time leads to the development of cultural humility.

Investigation of rf plasma light sources for dye laser excitation

International Nuclear Information System (INIS)

Kendall, J.S.; Jaminet, J.F.

1975-06-01

Analytical and experimental studies were performed to assess the applicability of radio frequency (rf) induction heated plasma light sources for potential excitation of continuous dye lasers. Experimental efforts were directed toward development of a continuous light source having spectral flux and emission characteristics approaching that required for pumping organic dye lasers. Analytical studies were performed to investigate (1) methods of pulsing the light source to obtain higher radiant intensity and (2) methods of integrating the source with a reflective cavity for pumping a dye cell. (TFD)

Field Measurements of Trace Gases and Aerosols Emitted by Undersampled Combustion Sources Including Wood and Dung Cooking Fires, Garbage and Crop Residue Burning, and Indonesian Peat Fires

Science.gov (United States)

Stockwell, C.; Jayarathne, T. S.; Goetz, D.; Simpson, I. J.; Selimovic, V.; Bhave, P.; Blake, D. R.; Cochrane, M. A.; Ryan, K. C.; Putra, E. I.; Saharjo, B.; Stone, E. A.; DeCarlo, P. F.; Yokelson, R. J.

2017-12-01

Field measurements were conducted in Nepal and in the Indonesian province of Central Kalimantan to improve characterization of trace gases and aerosols emitted by undersampled combustion sources. The sources targeted included cooking with a variety of stoves, garbage burning, crop residue burning, and authentic peat fires. Trace gas and aerosol emissions were studied using a land-based Fourier transform infrared spectrometer, whole air sampling, photoacoustic extinctiometers (405 and 870nm), and filter samples that were analyzed off-line. These measurements were used to calculate fuel-based emission factors (EFs) for up to 90 gases, PM2.5, and PM2.5 constituents. The aerosol optical data measured included EFs for the scattering and absorption coefficients, the single scattering albedo (at 870 and 405 nm), as well as the absorption Ångström exponent. The emissions varied significantly by source, although light absorption by both brown and black carbon (BrC and BC, respectively) was important for all non-peat sources. For authentic peat combustion, the emissions of BC were negligible and absorption was dominated by organic aerosol. The field results from peat burning were in reasonable agreement with recent lab measurements of smoldering Kalimantan peat and compare well to the limited data available from other field studies. The EFs can be used with estimates of fuel consumption to improve regional emissions inventories and assessments of the climate and health impacts of these undersampled sources.

Residual stress measurement using the pulsed neutron source at LANSCE

International Nuclear Information System (INIS)

Bourke, M.A.M.; Goldstone, J.A.; Holden, T.M.

1991-01-01

The presence of residual stress in engineering components can effect their mechanical properties and structural integrity. Neutron diffraction is the only measuring technique which can make spatially resolved non-destructive strain measurements in the interior of components. By recording the change in the crystalline interplanar spacing, elastic strains can be measured for individual lattice reflections. Using a pulsed neutron source, all the lattice reflections are recorded in each measurement which allows anisotropic effects to be studied. Measurements made at the Manuel Lujan Jr Neutron Scattering Centre (LANSCE) demonstrate the potential for stress measurements on a pulsed source and indicate the advantages and disadvantages over measurements made on a reactor. 15 refs., 7 figs

High-performance control of a three-phase voltage-source converter including feedforward compensation of the estimated load current

International Nuclear Information System (INIS)

Leon, Andres E.; Solsona, Jorge A.; Busada, Claudio; Chiacchiarini, Hector; Valla, Maria Ines

2009-01-01

In this paper a new control strategy for voltage-source converters (VSC) is introduced. The proposed strategy consists of a nonlinear feedback controller based on feedback linearization plus a feedforward compensation of the estimated load current. In our proposal an energy function and the direct-axis current are considered as outputs, in order to avoid the internal dynamics. In this way, a full linearization is obtained via nonlinear transformation and feedback. An estimate of the load current is feedforwarded to improve the performance of the whole system and to diminish the capacitor size. This estimation allows to obtain a more rugged and cheaper implementation. The estimate is calculated by using a nonlinear reduced-order observer. The proposal is validated through different tests. These tests include performance in presence of switching frequency, measurement filters delays, parameters uncertainties and disturbances in the input voltage.

Intercultural Education and the Crisis of Globalisation: Some Reflections

Science.gov (United States)

Coulby, David

2011-01-01

In this essay I reflect on the role of intercultural education in an emerging global crisis. Education systems are characterised by both divergent and convergent impulses. Divergent impulses include tradition, nationalism and religion. Convergent impulses (isomorphism) include science and technology, culture (including the English language),…

Liberating Moral Reflection

Science.gov (United States)

Horell, Harold D.

2013-01-01

The author argues that if we are to foster life-giving and liberating moral reflection, we must first liberate moral reflection from distortions; specifically, from the distorting effects of moral insensitivity, destructive moral relativism, and confusions resulting from a failure to understand the dynamics of moral reflection. The author proposes…

Newly graduated nurses' use of knowledge sources: a meta-ethnography.

Science.gov (United States)

Voldbjerg, Siri Lygum; Grønkjaer, Mette; Sørensen, Erik Elgaard; Hall, Elisabeth O C

2016-08-01

To advance evidence on newly graduated nurses' use of knowledge sources. Clinical decisions need to be evidence-based and understanding the knowledge sources that newly graduated nurses use will inform both education and practice. Qualitative studies on newly graduated nurses' use of knowledge sources are increasing though generated from scattered healthcare contexts. Therefore, a metasynthesis of qualitative research on what knowledge sources new graduates use in decision-making was conducted. Meta-ethnography. Nineteen reports, representing 17 studies, published from 2000-2014 were identified from iterative searches in relevant databases from May 2013-May 2014. Included reports were appraised for quality and Noblit and Hare's meta-ethnography guided the interpretation and synthesis of data. Newly graduated nurses' use of knowledge sources during their first 2-year postgraduation were interpreted in the main theme 'self and others as knowledge sources,' with two subthemes 'doing and following' and 'knowing and doing,' each with several elucidating categories. The metasynthesis revealed a line of argument among the report findings underscoring progression in knowledge use and perception of competence and confidence among newly graduated nurses. The transition phase, feeling of confidence and ability to use critical thinking and reflection, has a great impact on knowledge sources incorporated in clinical decisions. The synthesis accentuates that for use of newly graduated nurses' qualifications and skills in evidence-based practice, clinical practice needs to provide a supportive environment which nurtures critical thinking and questions and articulates use of multiple knowledge sources. © 2016 John Wiley & Sons Ltd.

Newly graduated nurses' use of knowledge sources

DEFF Research Database (Denmark)

Voldbjerg, Siri Lygum; Grønkjaer, Mette; Sørensen, Erik Elgaard

2016-01-01

AIM: To advance evidence on newly graduated nurses' use of knowledge sources. BACKGROUND: Clinical decisions need to be evidence-based and understanding the knowledge sources that newly graduated nurses use will inform both education and practice. Qualitative studies on newly graduated nurses' use...... underscoring progression in knowledge use and perception of competence and confidence among newly graduated nurses. CONCLUSION: The transition phase, feeling of confidence and ability to use critical thinking and reflection, has a great impact on knowledge sources incorporated in clinical decisions....... The synthesis accentuates that for use of newly graduated nurses' qualifications and skills in evidence-based practice, clinical practice needs to provide a supportive environment which nurtures critical thinking and questions and articulates use of multiple knowledge sources....

A nonlinear approach of elastic reflection waveform inversion

KAUST Repository

Guo, Qiang

2016-09-06

Elastic full waveform inversion (EFWI) embodies the original intention of waveform inversion at its inception as it is a better representation of the mostly solid Earth. However, compared with the acoustic P-wave assumption, EFWI for P- and S-wave velocities using multi-component data admitted mixed results. Full waveform inversion (FWI) is a highly nonlinear problem and this nonlinearity only increases under the elastic assumption. Reflection waveform inversion (RWI) can mitigate the nonlinearity by relying on transmissions from reflections focused on inverting low wavenumber components of the model. In our elastic endeavor, we split the P- and S-wave velocities into low wavenumber and perturbation components and propose a nonlinear approach to invert for both of them. The new optimization problem is built on an objective function that depends on both background and perturbation models. We utilize an equivalent stress source based on the model perturbation to generate reflection instead of demigrating from an image, which is applied in conventional RWI. Application on a slice of an ocean-bottom data shows that our method can efficiently update the low wavenumber parts of the model, but more so, obtain perturbations that can be added to the low wavenumbers for a high resolution output.

A nonlinear approach of elastic reflection waveform inversion

KAUST Repository

Guo, Qiang; Alkhalifah, Tariq Ali

2016-01-01

Elastic full waveform inversion (EFWI) embodies the original intention of waveform inversion at its inception as it is a better representation of the mostly solid Earth. However, compared with the acoustic P-wave assumption, EFWI for P- and S-wave velocities using multi-component data admitted mixed results. Full waveform inversion (FWI) is a highly nonlinear problem and this nonlinearity only increases under the elastic assumption. Reflection waveform inversion (RWI) can mitigate the nonlinearity by relying on transmissions from reflections focused on inverting low wavenumber components of the model. In our elastic endeavor, we split the P- and S-wave velocities into low wavenumber and perturbation components and propose a nonlinear approach to invert for both of them. The new optimization problem is built on an objective function that depends on both background and perturbation models. We utilize an equivalent stress source based on the model perturbation to generate reflection instead of demigrating from an image, which is applied in conventional RWI. Application on a slice of an ocean-bottom data shows that our method can efficiently update the low wavenumber parts of the model, but more so, obtain perturbations that can be added to the low wavenumbers for a high resolution output.

Analysing and Correcting the Differences between Multi-Source and Multi-Scale Spatial Remote Sensing Observations

Science.gov (United States)

Dong, Yingying; Luo, Ruisen; Feng, Haikuan; Wang, Jihua; Zhao, Jinling; Zhu, Yining; Yang, Guijun

2014-01-01

Differences exist among analysis results of agriculture monitoring and crop production based on remote sensing observations, which are obtained at different spatial scales from multiple remote sensors in same time period, and processed by same algorithms, models or methods. These differences can be mainly quantitatively described from three aspects, i.e. multiple remote sensing observations, crop parameters estimation models, and spatial scale effects of surface parameters. Our research proposed a new method to analyse and correct the differences between multi-source and multi-scale spatial remote sensing surface reflectance datasets, aiming to provide references for further studies in agricultural application with multiple remotely sensed observations from different sources. The new method was constructed on the basis of physical and mathematical properties of multi-source and multi-scale reflectance datasets. Theories of statistics were involved to extract statistical characteristics of multiple surface reflectance datasets, and further quantitatively analyse spatial variations of these characteristics at multiple spatial scales. Then, taking the surface reflectance at small spatial scale as the baseline data, theories of Gaussian distribution were selected for multiple surface reflectance datasets correction based on the above obtained physical characteristics and mathematical distribution properties, and their spatial variations. This proposed method was verified by two sets of multiple satellite images, which were obtained in two experimental fields located in Inner Mongolia and Beijing, China with different degrees of homogeneity of underlying surfaces. Experimental results indicate that differences of surface reflectance datasets at multiple spatial scales could be effectively corrected over non-homogeneous underlying surfaces, which provide database for further multi-source and multi-scale crop growth monitoring and yield prediction, and their corresponding

From the Atlas to the Rif a Crustal seismic image across Morocco: The SIMA & RIFSEIS control source wide-angle seismic reflection data

Science.gov (United States)

Carbonell, Ramon; Ayarza, Puy; Gallart, Josep; Diaz, Jordi; Harnafi, Mimoun; Levander, Alan; Teixell, Antonio

2014-05-01

The velocity structure of the crust and the geometry of the Moho across Morocco has been the main target of two recently acquired wide-angle seismic reflection transects. One is the SIMA experiment which provided seismic constraints beneath the Atlas Mountains and the second has been the RIFSEIS experiment which sampled the RIF orogen. Jointly these controlled source wide-angle seismic reflection data results in an almost 700 km, seismic profile going from the the Sahara craton across the High and Middle Atlas and Rif Mountain till the Gibraltar-Arc (Alboran). Current work on the interpretation of the seismic data-set is based on forward modeling, ray-tracing, as well as low fold wide-angle stacking. The data has resulted in a detailed crustal structure and velocity model for the Atlas Mountains and a 700 km transect revealing the irregular topography of the Moho beneath these two mountain orogens. Results indicate that the High Atlas features a moderate crustal thickness and that shortening is resolved at depth through a crustal root where the Saharan crust under-thrusts below the Moroccan crust, defining a lower crust imbrication which locally places the Moho boundary at, approximately, 40 km depth. The P-wave velocity model is characterized, in averaged, by relatively low velocities. These low deep crustal velocities together with other geophysical observables such as: conductivity estimates derived from Mt measurements; moderate Bouguer gravity anomaly; surface exposures of recent alkaline volcanics; lead the interpretation to propose that partial melts are currently emplaced in the deep crustal levels and in the upper mantle. The Moho discontinuity defines a crust which is in average relatively thin beneath the Atlas which is almost a 4000 m high orogenic belt. The resulting model supports existence of mantle upwelling as a possible mechanism that contributes, significantly, to maintain the High Atlas topography.

Pacemakers lower sources

International Nuclear Information System (INIS)

Greatbatch, W.

1984-01-01

Energy sources for cardiac facing are considered including radioisotope sources, in a broad conceptual and historical framework.The main guidelines for future development of energy sources are assessed

Reflection ciphers

DEFF Research Database (Denmark)

Boura, Christina; Canteaut, Anne; Knudsen, Lars Ramkilde

2017-01-01

study the necessary properties for this coupling permutation. Special care has to be taken of some related-key distinguishers since, in the context of reflection ciphers, they may provide attacks in the single-key setting.We then derive some criteria for constructing secure reflection ciphers...

Regression-based model of skin diffuse reflectance for skin color analysis

Science.gov (United States)

Tsumura, Norimichi; Kawazoe, Daisuke; Nakaguchi, Toshiya; Ojima, Nobutoshi; Miyake, Yoichi

2008-11-01

A simple regression-based model of skin diffuse reflectance is developed based on reflectance samples calculated by Monte Carlo simulation of light transport in a two-layered skin model. This reflectance model includes the values of spectral reflectance in the visible spectra for Japanese women. The modified Lambert Beer law holds in the proposed model with a modified mean free path length in non-linear density space. The averaged RMS and maximum errors of the proposed model were 1.1 and 3.1%, respectively, in the above range.

Theory of reflectivity blurring in seismic depth imaging

Science.gov (United States)

Thomson, C. J.; Kitchenside, P. W.; Fletcher, R. P.

2016-05-01

A subsurface extended image gather obtained during controlled-source depth imaging yields a blurred kernel of an interface reflection operator. This reflectivity kernel or reflection function is comprised of the interface plane-wave reflection coefficients and so, in principle, the gather contains amplitude versus offset or angle information. We present a modelling theory for extended image gathers that accounts for variable illumination and blurring, under the assumption of a good migration-velocity model. The method involves forward modelling as well as migration or back propagation so as to define a receiver-side blurring function, which contains the effects of the detector array for a given shot. Composition with the modelled incident wave and summation over shots then yields an overall blurring function that relates the reflectivity to the extended image gather obtained from field data. The spatial evolution or instability of blurring functions is a key concept and there is generally not just spatial blurring in the apparent reflectivity, but also slowness or angle blurring. Gridded blurring functions can be estimated with, for example, a reverse-time migration modelling engine. A calibration step is required to account for ad hoc band limitedness in the modelling and the method also exploits blurring-function reciprocity. To demonstrate the concepts, we show numerical examples of various quantities using the well-known SIGSBEE test model and a simple salt-body overburden model, both for 2-D. The moderately strong slowness/angle blurring in the latter model suggests that the effect on amplitude versus offset or angle analysis should be considered in more realistic structures. Although the description and examples are for 2-D, the extension to 3-D is conceptually straightforward. The computational cost of overall blurring functions implies their targeted use for the foreseeable future, for example, in reservoir characterization. The description is for scalar

Entanglement characteristics of subharmonic modes reflected from a cavity for type-II second-harmonic generation

International Nuclear Information System (INIS)

Zhai Zehui; Li Yongming; Gao Jiangrui

2004-01-01

Quantum fluctuation and quantum entanglement of the pump fields reflected from an optical cavity for type-II second-harmonic generation are theoretically analyzed. The correlation spectra of quadrature components between the reflected subharmonic fields are interpreted in terms of pump parameter, intracavity losses, and normalized frequency. High correlation of both amplitude and phase quadratures can be accessed in a triple resonant cavity before the pitchfork bifurcation occurs. The two reflected subharmonic fields are in an entangled state with quantum correlation of phase quadratures and anticorrelation of amplitude quadratures. The proposed system can be exploited as a source for generating entangled states of continuous variables

Fragments on teachers' reflective practicum

Directory of Open Access Journals (Sweden)

Živković Predrag Ž.

2013-01-01

Full Text Available in many historical and comparative overviews of the works, in which there is an analytical discussion of the dominant pedagogical theories in the twentieth century, John Dewey (Dewey, 1933 is referred to as the founder and creator of the concept of reflection (reflective thought and knowledge in practice. Reflection as a concept is understood as the forms and the form of problem solving, as well as continuously thinking about the causes of problems in situations in situ, including active and systematically and consistently changing connecting ideas with solutions to the problems and situations that preceded them (Hatton & Smith, 1995. Reflective thinking is the most general level to tackle practical problems, allowing the ''recommended'' doubts and confusion before proposing possible solutions to the problem. Dewey wrote about a reflective action which refers to the use of solutions to the problem and to thinking through the course of the action. in later works of the authors who have dealt with this problem, an unambiguous link can be observed between the so-called ''professional'' action and the reflection on action which, in this cyclical relationship, leads to visible changes (Zeichner & Gore, 1984. Already at first glance, this implies a connection with experiential learning and adult position of observation and reflection in various models of experiential learning, which will be discussed later. it would be useful to compare this method with a cyclic action of routine as an expression of impulse, tradition and authority. Reflective action, as opposed to the routine, is a consistently and carefully thought-out action (practice reflection, which is an ''awakened'' knowledge and belief, and that is an expression of openness, accountability and commitment. We are ready for reflection, says Schon, when the ''knowledge-in-action'' - a kind of knowledge that professionals notice when it is acted spontaneously - occurs suddenly and unintentionally

Source criticism and cultural models: constructing life histories of women missionaries

Directory of Open Access Journals (Sweden)

Eila Helander

1999-01-01

Full Text Available Research work is an interpretive enterprise. The variety of sources poses some central methodological questions for constructing religious life histories. There is an apparent discrepancy between the source categories concerning the content of the information. Private diaries and letters provide information on women's work and life which is not available in official reports and letters. They reveal dates, events and individuals which are not mentioned elsewhere. In histography the question of discrepancy is normally solved by comparing the sources with an aim to arrive at the "true picture" of how things have been. Such a picture is believed to portray not only the true life situation of the individual or group in question but, depending on the nature of the data, also the epoch and time situation itself. From the viewpoint of social sciences and comparative religion one will ask: could the variety of sources be approached and utilized in some other way? The second question posed by the data concerns the content of each source category. The information can be located on the continuum "highly subjective — stereotyped". Subjective information, including reflections on personal experiences may not be the best source e.g. for constructing the flow of historical events, but it is of uttermost importance if we want to show how individuals respond to social constraints and actively assemble social worlds.

Cell sources for in vitro human liver cell culture models

Science.gov (United States)

Freyer, Nora; Damm, Georg; Seehofer, Daniel; Knöspel, Fanny

2016-01-01

In vitro liver cell culture models are gaining increasing importance in pharmacological and toxicological research. The source of cells used is critical for the relevance and the predictive value of such models. Primary human hepatocytes (PHH) are currently considered to be the gold standard for hepatic in vitro culture models, since they directly reflect the specific metabolism and functionality of the human liver; however, the scarcity and difficult logistics of PHH have driven researchers to explore alternative cell sources, including liver cell lines and pluripotent stem cells. Liver cell lines generated from hepatomas or by genetic manipulation are widely used due to their good availability, but they are generally altered in certain metabolic functions. For the past few years, adult and pluripotent stem cells have been attracting increasing attention, due their ability to proliferate and to differentiate into hepatocyte-like cells in vitro. However, controlling the differentiation of these cells is still a challenge. This review gives an overview of the major human cell sources under investigation for in vitro liver cell culture models, including primary human liver cells, liver cell lines, and stem cells. The promises and challenges of different cell types are discussed with a focus on the complex 2D and 3D culture approaches under investigation for improving liver cell functionality in vitro. Finally, the specific application options of individual cell sources in pharmacological research or disease modeling are described. PMID:27385595

Plasma sources for EUV lithography exposure tools

International Nuclear Information System (INIS)

Banine, Vadim; Moors, Roel

2004-01-01

The source is an integral part of an extreme ultraviolet lithography (EUVL) tool. Such a source, as well as the EUVL tool, has to fulfil extremely high demands both technical and cost oriented. The EUVL tool operates at a wavelength in the range 13-14 nm, which requires a major re-thinking of state-of-the-art lithography systems operating in the DUV range. The light production mechanism changes from conventional lamps and lasers to relatively high temperature emitting plasmas. The light transport, mainly refractive for DUV, should become reflective for EUV. The source specifications are derived from the customer requirements for the complete tool, which are: throughput, cost of ownership (CoO) and imaging quality. The EUVL system is considered as a follow up of the existing DUV based lithography technology and, while improving the feature resolution, it has to maintain high wafer throughput performance, which is driven by the overall CoO picture. This in turn puts quite high requirements on the collectable in-band power produced by an EUV source. Increased, due to improved feature resolution, critical dimension (CD) control requirements, together with reflective optics restrictions, necessitate pulse-to-pulse repeatability, spatial stability control and repetition rates, which are substantially better than those of current optical systems. All together the following aspects of the source specification will be addressed: the operating wavelength, the EUV power, the hot spot size, the collectable angle, the repetition rate, the pulse-to-pulse repeatability and the debris induced lifetime of components

Sources of tropospheric ozone along the Asian Pacific Rim: An analysis of ozonesonde observations

Science.gov (United States)

Liu, Hongyu; Jacob, Daniel J.; Chan, Lo Yin; Oltmans, Samuel J.; Bey, Isabelle; Yantosca, Robert M.; Harris, Joyce M.; Duncan, Bryan N.; Martin, Randall V.

2002-11-01

The sources contributing to tropospheric ozone over the Asian Pacific Rim in different seasons are quantified by analysis of Hong Kong and Japanese ozonesonde observations with a global three-dimensional (3-D) chemical transport model (GEOS-CHEM) driven by assimilated meteorological observations. Particular focus is placed on the extensive observations available from Hong Kong in 1996. In the middle-upper troposphere (MT-UT), maximum Asian pollution influence along the Pacific Rim occurs in summer, reflecting rapid convective transport of surface pollution. In the lower troposphere (LT) the season of maximum Asian pollution influence shifts to summer at midlatitudes from fall at low latitudes due to monsoonal influence. The UT ozone minimum and high variability observed over Hong Kong in winter reflects frequent tropical intrusions alternating with stratospheric intrusions. Asian biomass burning makes a major contribution to ozone at pollution influence (pollution influence exceeds European influence in the UT-MT, reflecting the uplift from convection and the warm conveyor belts over the eastern seaboard of North America. African outflow makes a major contribution to ozone in the low-latitude MT-UT over the Pacific Rim during November-April. Lightning influence over the Pacific Rim is minimum in summer due to westward UT transport at low latitudes associated with the Tibetan anticyclone. The Asian outflow flux of ozone to the Pacific is maximum in spring and fall and includes a major contribution from Asian anthropogenic sources year-round.

Evaluation of retro-reflective coating performance by reflectance and perceived relative brightness measurements

International Nuclear Information System (INIS)

Luse, Kaiva; Pausus, Anete; Karitans, Varis; Ozolins, Maris; Tukisa, Madara

2011-01-01

Retro-reflective properties of six types and five different colors or retro-reflective materials were discussed in this paper. Reflectance optical indicatrix of samples was determined and compared to obtained psychophyisical data of perceived brightness of human observer. Microscopic structure of the retro-reflective active regions of RR's was studied. Statistically significant differences in reflectivity and brightness of various types and colors of RR's were found.

Diffuse reflectance infrared Fourier-Transform spectra of selected organic compounds

Energy Technology Data Exchange (ETDEWEB)

Harmon, S.H.; Caton, J.E.

1982-05-01

Diffuse reflectance infrared spectra of a variety of different organic compounds have been determined. Profiles of the spectra along with the location and relative intensity of the principal bands have been included for each compound studied. In addition both diffuse reflectance and transmittance infrared spectra were obtained for the same samples, and the spectral results were compared. Although some minor variations are observed between a diffuse reflectance spectrum and the corresponding transmittance spectrum, the diffuse reflectance is quite useful and may be a superior technique for the study of many samples because it possesses an inherently higher signal-to-noise response, requires less sample preparation and allows a very wide range of samples (solids, liquids of low volatility, neat sample, or sample diluted in a reflecting medium) to be studied under very similar conditions.

Discovery of source fault in the region without obvious active fault. Geophysical survey in the source area of the 1984 western Nagano prefecture earthquake

International Nuclear Information System (INIS)

Aoyagi, Yasuhira; Abe, Shintaro

2009-01-01

The 1984 Western Nagano Prefecture Earthquake (MJ6.8) occurred at shallow part of the southern foot of Mt. Ontake volcano, central Japan. Despite the large magnitude neither clear surface rupture nor active fault has been found around the source area. Therefore the earthquake is an issue for seismic assessment based on active fault survey. The purpose of this study is to find any tectonic geomorphologic features in the source area and to elucidate its relation to the source fault. In order to achieve it, an integrated survey with (1) micro earthquake observation, (2) airborne LIDAR, and (3) seismic reflection survey was demonstrated in the source area from 2006 to 2008. The survey area of airborne LIDAR (18 km x 4 km) covers main part of the aftershock distribution just after the mainshock. A linear zone with abrupt change of topographic roughness was found in ENE-WSW direction at the center of the LIDAR target area. River valleys flowing down to SSE direction change their directions and widths abruptly across the linear zone. Seismic reflection survey across the source region detect deformation zone just beneath the linear zone. These features of topographic and crustal deformation coincide well with the aftershock distribution. Therefore they indicate an active structure formed by the cumulative displacement of the source fault. (author)

Reflective writing: the student nurse's perspective on reflective writing and poetry writing.

Science.gov (United States)

Coleman, Dawn; Willis, Diane S

2015-07-01

Reflective writing is a mandatory part of nurse education but how students develop their skills and use reflection as part of their experiential learning remains relatively unknown. Understanding reflective writing in all forms from the perspective of a student nurse is therefore important. To explore the use of reflective writing and the use of poetry in pre-registered nursing students. A qualitative design was employed to explore reflective writing in pre-registered nursing students. A small university in Scotland. BSc (Hons) Adult and Mental Health Pre-registration Student Nurses. Two focus groups were conducted with 10 student nurses during March 2012. Data was analysed thematically using the framework of McCarthy (1999). Students found the process of reflective writing daunting but valued it over time. Current educational methods, such as assessing reflective accounts, often lead to the 'narrative' being watered down and the student feeling judged. Despite this, reflection made students feel responsible for their own learning and research on the topic. Some students felt the use of models of reflection constricting, whilst poetry freed up their expression allowing them to demonstrate the compassion for their patient under their care. Poetry writing gives students the opportunity for freedom of expression, personal satisfaction and a closer connection with their patients, which the more formal approach to reflective writing did not offer. There is a need for students to have a safe and supportive forum in which to express and have their experiences acknowledged without the fear of being judged. Crown Copyright © 2015. Published by Elsevier Ltd. All rights reserved.

Evaluation of retro-reflective coating performance by reflectance and perceived relative brightness measurements

Energy Technology Data Exchange (ETDEWEB)

Luse, Kaiva; Pausus, Anete; Karitans, Varis; Ozolins, Maris; Tukisa, Madara, E-mail: kaiva.luse@gmail.com [University of Latvia, Optometry and Vision Science Department, Kengaraga street 8, Riga LV-1063 (Latvia)

2011-06-23

Retro-reflective properties of six types and five different colors or retro-reflective materials were discussed in this paper. Reflectance optical indicatrix of samples was determined and compared to obtained psychophyisical data of perceived brightness of human observer. Microscopic structure of the retro-reflective active regions of RR's was studied. Statistically significant differences in reflectivity and brightness of various types and colors of RR's were found.

Laser driven white light source for BRDF measurement

DEFF Research Database (Denmark)

Amdemeskel, Mekbib Wubishet; Thorseth, Anders; Dam-Hansen, Carsten

2017-01-01

In this paper, we will present a setup with laser driven light source (LDLS) for measuring a 2D bidirectional reflectance distribution function (BRDF). We have carried out measurements to acquire the BRDF of different samples based on our setup: which consists of a new laser driven broadband light...... source (UV-VIS-NIR), spectroradiometer and sample holder stepper motor in a dark UV-protected environment. Here, we introduced a special kind of light source which has a bright, stable, broad spectral range and well collimated light output to give a very good angular resolution. The experimental results...

A revised dosimetric characterization of the model S700 electronic brachytherapy source containing an anode-centering plastic insert and other components not included in the 2006 model.

Science.gov (United States)

Hiatt, Jessica R; Davis, Stephen D; Rivard, Mark J

2015-06-01

The model S700 Axxent electronic brachytherapy source by Xoft, Inc., was characterized by Rivard et al. in 2006. Since then, the source design was modified to include a new insert at the source tip. Current study objectives were to establish an accurate source model for simulation purposes, dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and determine dose differences between the original simulation model and the current model S700 source design. Design information from measurements of dissected model S700 sources and from vendor-supplied CAD drawings was used to aid establishment of an updated Monte Carlo source model, which included the complex-shaped plastic source-centering insert intended to promote water flow for cooling the source anode. These data were used to create a model for subsequent radiation transport simulations in a water phantom. Compared to the 2006 simulation geometry, the influence of volume averaging close to the source was substantially reduced. A track-length estimator was used to evaluate collision kerma as a function of radial distance and polar angle for determination of TG-43 dosimetry parameters. Results for the 50 kV source were determined every 0.1 cm from 0.3 to 15 cm and every 1° from 0° to 180°. Photon spectra in water with 0.1 keV resolution were also obtained from 0.5 to 15 cm and polar angles from 0° to 165°. Simulations were run for 10(10) histories, resulting in statistical uncertainties on the transverse plane of 0.04% at r = 1 cm and 0.06% at r = 5 cm. The dose-rate distribution ratio for the model S700 source as compared to the 2006 model exceeded unity by more than 5% for roughly one quarter of the solid angle surrounding the source, i.e., θ ≥ 120°. The radial dose function diminished in a similar manner as for an (125)I seed, with values of 1.434, 0.636, 0.283, and 0.0975 at 0.5, 2, 5, and 10 cm, respectively. The radial dose function ratio between the current

Evaluating Multispectral Snowpack Reflectivity With Changing Snow Correlation Lengths

Science.gov (United States)

Kang, Do Hyuk; Barros, Ana P.; Kim, Edward J.

2016-01-01

This study investigates the sensitivity of multispectral reflectivity to changing snow correlation lengths. Matzler's ice-lamellae radiative transfer model was implemented and tested to evaluate the reflectivity of snow correlation lengths at multiple frequencies from the ultraviolet (UV) to the microwave bands. The model reveals that, in the UV to infrared (IR) frequency range, the reflectivity and correlation length are inversely related, whereas reflectivity increases with snow correlation length in the microwave frequency range. The model further shows that the reflectivity behavior can be mainly attributed to scattering rather than absorption for shallow snowpacks. The largest scattering coefficients and reflectivity occur at very small correlation lengths (approximately 10(exp -5 m) for frequencies higher than the IR band. In the microwave range, the largest scattering coefficients are found at millimeter wavelengths. For validation purposes, the ice-lamella model is coupled with a multilayer snow physics model to characterize the reflectivity response of realistic snow hydrological processes. The evolution of the coupled model simulated reflectivities in both the visible and the microwave bands is consistent with satellite-based reflectivity observations in the same frequencies. The model results are also compared with colocated in situ snow correlation length measurements (Cold Land Processes Field Experiment 2002-2003). The analysis and evaluation of model results indicate that the coupled multifrequency radiative transfer and snow hydrology modeling system can be used as a forward operator in a data-assimilation framework to predict the status of snow physical properties, including snow correlation length.

Reflection as Self-Assessment

Science.gov (United States)

Pappas, Marjorie L.

2010-01-01

In this article, the author discusses how reflection can be used as self-assessment. Reflection involves not only thinking about a learning experience, but also questioning parts of the experience. Reflection is thinking about what one knows from the learning experience, what one might do differently the next time. Reflection is wondering about…

Research Needs: Glass Solar Reflectance and Vinyl Siding

Energy Technology Data Exchange (ETDEWEB)

Hart, Robert; Curcija, Charlie; Arasteh, Dariush; Goudey, Howdy; Kohler, Christian; Selkowitz, Stephen

2011-07-07

The subject of glass solar reflectance and its contribution to permanent vinyl siding distortion has not been extensively studied, and some phenomena are not yet well understood. This white paper presents what is known regarding the issue and identifies where more research is needed. Three primary topics are discussed: environmental factors that control the transfer of heat to and from the siding surface; vinyl siding properties that may affect heat build-up and permanent distortion; and factors that determine the properties of reflected solar radiation from glass surfaces, including insulating window glass. Further research is needed to fully characterize the conditions associated with siding distortion, the scope of the problem, physical properties of vinyl siding, insulating window glass reflection characteristics, and possible mitigation or prevention strategies.

Issues in reflection and debriefing: how nurse educators structure experiential activities.

Science.gov (United States)

Brackenreg, Jenni

2004-12-01

Experiential learning is particularly useful in vocational education programs where theory needs to be linked to practice. Although experiential learning is often advocated in nursing education and the importance of debriefing and reflection is almost always espoused, the focus in the literature has tended to be on detailed descriptions of the action phase with little close analysis of how the reflective phase is facilitated. The Lewinian model described by Kolb [Experiential Learning. Experience as Source of Learning and Development, Prentice-Hall, New Jersey, 1984] and the structuring approach suggested by Thiagarajan [Experiential Learning Packages, Prentice-Hall, Englewood Cliffs, NJ, 1980] have been used as the theoretical context for an exploration of how nurse teachers describe their facilitation of the debriefing and reflective phases of experiential learning activities. Explication of the entire planned experiential learning experience is important for increasing the chances of the student being able to close the experiential learning loop. The more covert reflective phases for facilitating experiential learning are crucial and if neglected, or inexpertly and insensitively handled, may at best lead to poor learning outcomes or at worst lead to emotional damage and ;unfinished business' for the student. Interviews with eight experienced university educators elicited descriptions of how they constructed experiential activities with special reference to their descriptions of how the debriefing or reflective phases were structured.

Exploring Planetary Analogs With an Ultracompact Near-Infrared Reflectance Instrument

Science.gov (United States)

Sobron, P.; Wang, A.

2017-12-01

Orbital reflectance spectrometers provide unique measurements of mineralogical features globally and repeatedly on planets and moons of our solar system. Mounted on landed spacecraft, reflectance sensors enable fine-scale investigations and can provide ground truth analyses to assess the validity of spectral remote sensing. We have developed a miniaturized, field-ready, active source NIR (1.14-4.76 μm) reflectance spectrometer (WIR) WIR enables in-situ, near real-time identification of water (structural or adsorbed), carbonates, sulfates, hydrated silicates, as well as C-H & N-H bonds in organic species. WIR is suited for lander/rover deployment in two modes: 1) In Traverse Survey Mode WIR is integrated into a rover wheel and performs nonstop synchronized data collection with every revolution of the wheel; large amounts of data points can be collected during a rover traverse that inform the spatial distribution of mineral phases; 2) In Point-Check Mode WIR is mounted on a robotic arm of a rover/lander and deployed on selected targets at planetary surfaces, or installed inside an analytical lab where samples from a drill/scoop are delivered for detailed analysis. Over the past 10 years we have deployed WIR in planetary analog settings, including hydrothermal springs in Svalbard (Norway) and High Andes (Chile); Arctic volcanoes in Svalbard; Arctic springs and permafrost in Axel Heiberg (Canada); Antarctic ice-covered lakes; saline playas in hyperarid deserts in the Tibetan Plateau (China) and the Atacama; high elevation ore deposits in the Andes and the Abitibi gold belt region (Canada); lava tubes in California; and acidic waters in Rio Tinto (Spain). We have recorded in-situ NIR reflectance spectra from these analogues and used improved spectral unmixing algorithms to determine the mineralogical composition at these sites. We have observed minerals consistent with sedimentary, mineralogical, morphological, and geochemical processes, some of which have been

Student Reflection Papers on a Global Clinical Experience: A Qualitative Study.

Science.gov (United States)

Margolis, Carmi Z; Rohrbaugh, Robert M; Tsang, Luisa; Fleischer, Jennifer; Graham, Mark J; Kellett, Anne; Hafler, Janet P

Many of the 70,000 graduating US medical students [per year] have reported participating in a global health activity at some stage of medical school. This case study design provided a method for understanding the student's experience that included student's learning about culture, health disparities, exposure and reaction to a range of diseases actually encountered. The broad diversity of themes among students indicated that the GCE provided a flexible, personalized experience. We need to understand the student's experience in order to help design appropriate curricular experiences [and valid student assessment]. Our research aim was to analyze medical student reflection papers to understand how they viewed their Global Clinical Experience (GCE). A qualitative case study design was used to analyze student reflection papers. All 28 students who participated in a GCE from 2008-2010 and in 2014-2015 and submitted a reflection paper on completion of the GCE were eligible to participate in the study. One student did not submit a reflection paper and was not included in the study. All 27 papers were coded by paragraph for reflection and for themes. System of Care/Range of Care was mentioned most often, Aids to Adjustment Process was mentioned least. The theme, "Diseases," referred to any mention of a disease in the reflection papers, and 44 diseases were mentioned in the papers. The analysis for depth of reflection yielded the following data: Observation, 81/248 paragraphs; Observation and Interpretation, 130/248 paragraphs; and Observation, Interpretation, and Suggestions for change, 36/248 paragraphs; 9 reflection papers contained 27 separate accounts of a transformational experience. This study provided a method for understanding the student's experience that included student's learning about culture, health disparities, and exposure and reaction to a range of diseases actually encountered. The broad diversity of themes among students indicated that the GCE provided a

Designing a Reflective Teacher Education Course and Its Contribution to ELT Teachers' Reflectivity

Science.gov (United States)

Tajik, Leila; Pakzad, Kazem

2016-01-01

Researchers in the present study planned a reflective teacher education course and documented the contribution of such a course to improving teachers' reflectivity. Five English teachers took part in the reflective teacher education course designed by the researchers. To record how the course could help improve reflective teaching, researchers…

tomo3d: a new 3-D joint refraction and reflection travel-time tomography code for active-source seismic data

Science.gov (United States)

Meléndez, A.; Korenaga, J.; Sallares, V.; Ranero, C. R.

2012-12-01

We present the development state of tomo3d, a code for three-dimensional refraction and reflection travel-time tomography of wide-angle seismic data based on the previous two-dimensional version of the code, tomo2d. The core of both forward and inverse problems is inherited from the 2-D version. The ray tracing is performed by a hybrid method combining the graph and bending methods. The graph method finds an ordered array of discrete model nodes, which satisfies Fermat's principle, that is, whose corresponding travel time is a global minimum within the space of discrete nodal connections. The bending method is then applied to produce a more accurate ray path by using the nodes as support points for an interpolation with beta-splines. Travel time tomography is formulated as an iterative linearized inversion, and each step is solved using an LSQR algorithm. In order to avoid the singularity of the sensitivity kernel and to reduce the instability of inversion, regularization parameters are introduced in the inversion in the form of smoothing and damping constraints. Velocity models are built as 3-D meshes, and velocity values at intermediate locations are obtained by trilinear interpolation within the corresponding pseudo-cubic cell. Meshes are sheared to account for topographic relief. A floating reflector is represented by a 2-D grid, and depths at intermediate locations are calculated by bilinear interpolation within the corresponding square cell. The trade-off between the resolution of the final model and the associated computational cost is controlled by the relation between the selected forward star for the graph method (i.e. the number of nodes that each node considers as its neighbors) and the refinement of the velocity mesh. Including reflected phases is advantageous because it provides a better coverage and allows us to define the geometry of those geological interfaces with velocity contrasts sharp enough to be observed on record sections. The code also

Using Online Learning Platforms to Enhance Students' Reflective and Critical Thinking

Science.gov (United States)

Lennon, Sean M.

2010-01-01

A working paper on how to use common E-Learning platforms to incorporate critical thinking and reflection into traditional and hybrid formatted curriculums. Definitions and conceptual framework of both constructs are discussed and their benefits towards cognitions and reflection are highlighted. Best practices, including examples of previous…

Soft X-ray reflectivity: from quasi-perfect mirrors to accelerator walls

CERN Document Server

Schäfers, F.

2013-04-22

Reflection of light from surfaces is a very common, but complex phenomenon not only in science and technology, but in every day life. The underlying basic optical principles have been developed within the last five centuries using visible light available from the sun or other laboratory light sources. X-rays were detected in 1895, and the full potential of soft- and hard-x ray radiation as a probe for the electronic and geometric properties of matter, for material analysis and its characterisation is available only since the advent of synchrotron radiation sources some 50 years ago. On the other hand high-brilliance and high power synchrotron radiation of present-days 3rd and 4th generation light sources is not always beneficial. Highenergy machines and accelerator-based light sources can suffer from a serious performance drop or limitations due to interaction of the synchrotron radiation with the accelerator walls, thus producing clouds of photoelectrons (e-cloud) which in turn interact with the accelerated ...

Self-Reflection

DEFF Research Database (Denmark)

Fausing, Bent

2016-01-01

will take a look at the establishing of the modern self and possibilities of self-reflection, too. My examples will be from the so-called dark-selfies and from a new selfie form, which merge the present with the previous progressing into the future. I will discuss the media reflections as loos and/or gain...

Personal Reflections

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education. Personal Reflections. Articles in Resonance – Journal of Science Education. Volume 6 Issue 3 March 2001 pp 90-93 Personal Reflections. Why did I opt for Career in Science? Jayant V Narlikar · More Details Fulltext PDF. Volume 9 Issue 8 August 2004 pp 89-89 ...

Selenium speciation from food source to metabolites: a critical review

Energy Technology Data Exchange (ETDEWEB)

Dumont, Emmie; Vanhaecke, Frank; Cornelis, Rita [Ghent University, Department of Analytical Chemistry, Ghent (Belgium)

2006-08-15

Especially in the last decade, a vast number of papers on Se and its role in health issues have been published. This review gives a brief, critical overview of the main analytical findings reported in these papers. Of particular interest is the Se content in different food sources worldwide and the extent to which their consumption is reflected in the Se content of human tissues and body fluids. Several food sources, both natural (Brazil nuts, garlic, Brassica juncea) and Se-enriched (yeast-based supplements), are discussed as to origin, characteristics, Se metabolism and impact of their consumption on the human body. The continuous development of new and improvement of existing analytical techniques has provided different powerful tools to unravel the Se species and their function. An up-to-date literature study on Se speciation analysis is given, illustrating how analytical chemistry in its different facets aids in the identification of Se compounds and provides insight into the complete metabolic pathway of Se throughout the human body. This review includes a detailed image of the current state-of-the-art of Se speciation analysis in these food sources and in human tissues and body fluids. (orig.)

26 CFR 31.3402(e)-1 - Included and excluded wages.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 15 2010-04-01 2010-04-01 false Included and excluded wages. 31.3402(e)-1... SOURCE Collection of Income Tax at Source § 31.3402(e)-1 Included and excluded wages. (a) If a portion of... not more than 31 consecutive days constitutes wages, and the remainder does not constitute wages, all...

Method of Detecting Coliform Bacteria from Reflected Light

Science.gov (United States)

Vincent, Robert K. (Inventor)

2014-01-01

The present invention relates to a method of detecting coliform bacteria in water from reflected light, and also includes devices for the measurement, calculation and transmission of data relating to that method.

Irradiation facilities at the advanced neutron source

International Nuclear Information System (INIS)

West, C.D.

1992-01-01

The Advanced Neutron Source (ANS) is a facility, centered around a new 330MW(f) heavy-water cooled and reflected research reactor, proposed for construction at Oak Ridge. The main scientific justification for the new source is the United States' need for increased capabilities in neutron scattering and other neutron beam research, but the technical objectives of the project also cater for the need to replace the irradiation facilities at the aging High Flux Isotope Reactor and to provide other research capabilities to the scientific community. This document provides a description of the ANS facilities

A Precise Visual Method for Narrow Butt Detection in Specular Reflection Workpiece Welding

Directory of Open Access Journals (Sweden)

Jinle Zeng

2016-09-01

Full Text Available During the complex path workpiece welding, it is important to keep the welding torch aligned with the groove center using a visual seam detection method, so that the deviation between the torch and the groove can be corrected automatically. However, when detecting the narrow butt of a specular reflection workpiece, the existing methods may fail because of the extremely small groove width and the poor imaging quality. This paper proposes a novel detection method to solve these issues. We design a uniform surface light source to get high signal-to-noise ratio images against the specular reflection effect, and a double-line laser light source is used to obtain the workpiece surface equation relative to the torch. Two light sources are switched on alternately and the camera is synchronized to capture images when each light is on; then the position and pose between the torch and the groove can be obtained nearly at the same time. Experimental results show that our method can detect the groove effectively and efficiently during the welding process. The image resolution is 12.5 μm and the processing time is less than 10 ms per frame. This indicates our method can be applied to real-time narrow butt detection during high-speed welding process.

Qualitative evaluation of the implementation of the Interdisciplinary Management Tool: a reflective tool to enhance interdisciplinary teamwork using Structured, Facilitated Action Research for Implementation.

Science.gov (United States)

Nancarrow, Susan A; Smith, Tony; Ariss, Steven; Enderby, Pamela M

2015-07-01

Reflective practice is used increasingly to enhance team functioning and service effectiveness; however, there is little evidence of its use in interdisciplinary teams. This paper presents the qualitative evaluation of the Interdisciplinary Management Tool (IMT), an evidence-based change tool designed to enhance interdisciplinary teamwork through structured team reflection. The IMT incorporates three components: an evidence-based resource guide; a reflective implementation framework based on Structured, Facilitated Action Research for Implementation methodology; and formative and summative evaluation components. The IMT was implemented with intermediate care teams supported by independent facilitators in England. Each intervention lasted 6 months and was evaluated over a 12-month period. Data sources include interviews, a focus group with facilitators, questionnaires completed by team members and documentary feedback from structured team reports. Data were analysed qualitatively using the Framework approach. The IMT was implemented with 10 teams, including 253 staff from more than 10 different disciplines. Team challenges included lack of clear vision; communication issues; limited career progression opportunities; inefficient resource use; need for role clarity and service development. The IMT successfully engaged staff in the change process, and resulted in teams developing creative strategies to address the issues identified. Participants valued dedicated time to focus on the processes of team functioning; however, some were uncomfortable with a focus on teamwork at the expense of delivering direct patient care. The IMT is a relatively low-cost, structured, reflective way to enhance team function. It empowers individuals to understand and value their own, and others' roles and responsibilities within the team; identify barriers to effective teamwork, and develop and implement appropriate solutions to these. To be successful, teams need protected time to take

Do writing and storytelling skill influence assessment of reflective ability in medical students' written reflections?

Science.gov (United States)

Aronson, Louise; Niehaus, Brian; DeVries, Charlie D; Siegel, Jennifer R; O'Sullivan, Patricia S

2010-10-01

Increasingly, students are asked to write reflections as part of their medical education, but some question the influence of other factors on the evaluation of these reflections. In this pilot study, the investigators determined whether scores from a validated rubric to measure reflective ability were affected by irrelevant variance resulting from writing or storytelling ability. Students in clerkships wrote reflections on professionalism. All were given identical prompts, with half receiving additional structured guidelines on reflection. Sixty reflections, 30 from each group, were randomly chosen and scored for reflection, writing, and storytelling by trained raters using validated rubrics. There was no correlation between reflection and either writing (r = 0.049, P = .35) or storytelling (r = 0.14, P = .13). The guidelines increased reflection, but not writing or storytelling scores. Reflection is a distinct construct unaffected by learners' writing or storytelling skills. These findings support reflective ability as a distinct skill.

Elementary school science teachers' reflection for nature of science: Workshop of NOS explicit and reflective on force and motion learning activity

Science.gov (United States)

Patho, Khanittha; Yuenyong, Chokchai; Chamrat, Suthida

2018-01-01

The nature of science has been part of Thailand's science education curriculum since 2008. However, teachers lack of understanding about the nature of science (NOS) and its teaching, particularly element school science teachers. In 2012, the Science Institute of Thailand MOE, started a project of Elementary Science Teacher Professional Development to enhance their thinking about the Nature of Science. The project aimed to enhance teachers' understanding of NOS, science teaching for explicit and reflective NOS, with the aim of extending their understanding of NOS to other teachers. This project selected 366 educational persons. The group was made up of a teacher and a teacher supervisor from 183 educational areas in 74 provinces all Thailand. The project provided a one week workshop and a year's follow up. The week-long workshop consisted of 11 activities of science teaching for explicit reflection on 8 aspects of NOS. Workshop of NOS explicit and reflective on force and motion learning activity is one of eight activities. This activity provided participants to learn force and motion and NOS from the traditional toy "Bang-Poh". The activity tried to enhance participants to explicit NOS for 5 aspects including empirical basis, subjectivity, creativity, observation and inference, and sociocultural embeddedness. The explicit NOS worksheet provided questions to ask participants to reflect their existing ideas about NOS. The paper examines elementary school science teachers' understanding of NOS from the force and motion learning activity which provided explicit reflection on 5 NOS aspects. An interpretive paradigm was used to analyse the teachers' reflections in a NOS worksheet. The findings indicated that majority of them could reflect about the empirical basis of science and creativity but few reflected on observation and inference, or sociocultural embeddedness. The paper will explain the teachers' NOS thinking and discuss the further enhancing of their understanding

Radiation sources working group summary

International Nuclear Information System (INIS)

Fazio, M.V.

1998-01-01

The Radiation Sources Working Group addressed advanced concepts for the generation of RF energy to power advanced accelerators. The focus of the working group included advanced sources and technologies above 17 GHz. The topics discussed included RF sources above 17 GHz, pulse compression techniques to achieve extreme peak power levels, components technology, technology limitations and physical limits, and other advanced concepts. RF sources included gyroklystrons, magnicons, free-electron masers, two beam accelerators, and gyroharmonic and traveling wave devices. Technology components discussed included advanced cathodes and electron guns, high temperature superconductors for producing magnetic fields, RF breakdown physics and mitigation, and phenomena that impact source design such as fatigue in resonant structures due to RF heating. New approaches for RF source diagnostics located internal to the source were discussed for detecting plasma and beam phenomena existing in high energy density electrodynamic systems in order to help elucidate the reasons for performance limitations

A revised dosimetric characterization of the model S700 electronic brachytherapy source containing an anode-centering plastic insert and other components not included in the 2006 model

International Nuclear Information System (INIS)

Hiatt, Jessica R.; Davis, Stephen D.; Rivard, Mark J.

2015-01-01

Purpose: The model S700 Axxent electronic brachytherapy source by Xoft, Inc., was characterized by Rivard et al. in 2006. Since then, the source design was modified to include a new insert at the source tip. Current study objectives were to establish an accurate source model for simulation purposes, dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and determine dose differences between the original simulation model and the current model S700 source design. Methods: Design information from measurements of dissected model S700 sources and from vendor-supplied CAD drawings was used to aid establishment of an updated Monte Carlo source model, which included the complex-shaped plastic source-centering insert intended to promote water flow for cooling the source anode. These data were used to create a model for subsequent radiation transport simulations in a water phantom. Compared to the 2006 simulation geometry, the influence of volume averaging close to the source was substantially reduced. A track-length estimator was used to evaluate collision kerma as a function of radial distance and polar angle for determination of TG-43 dosimetry parameters. Results for the 50 kV source were determined every 0.1 cm from 0.3 to 15 cm and every 1° from 0° to 180°. Photon spectra in water with 0.1 keV resolution were also obtained from 0.5 to 15 cm and polar angles from 0° to 165°. Simulations were run for 10 10 histories, resulting in statistical uncertainties on the transverse plane of 0.04% at r = 1 cm and 0.06% at r = 5 cm. Results: The dose-rate distribution ratio for the model S700 source as compared to the 2006 model exceeded unity by more than 5% for roughly one quarter of the solid angle surrounding the source, i.e., θ ≥ 120°. The radial dose function diminished in a similar manner as for an 125 I seed, with values of 1.434, 0.636, 0.283, and 0.0975 at 0.5, 2, 5, and 10 cm, respectively. The radial dose function

A revised dosimetric characterization of the model S700 electronic brachytherapy source containing an anode-centering plastic insert and other components not included in the 2006 model

Energy Technology Data Exchange (ETDEWEB)

Hiatt, Jessica R. [Department of Radiation Oncology, Rhode Island Hospital, The Warren Alpert Medical School of Brown University, Providence, Rhode Island 02903 (United States); Davis, Stephen D. [Department of Medical Physics, McGill University Health Centre, Montreal, Quebec H3G 1A4 (Canada); Rivard, Mark J., E-mail: mark.j.rivard@gmail.com [Department of Radiation Oncology, Tufts University School of Medicine, Boston, Massachusetts 02111 (United States)

2015-06-15

Purpose: The model S700 Axxent electronic brachytherapy source by Xoft, Inc., was characterized by Rivard et al. in 2006. Since then, the source design was modified to include a new insert at the source tip. Current study objectives were to establish an accurate source model for simulation purposes, dosimetrically characterize the new source and obtain its TG-43 brachytherapy dosimetry parameters, and determine dose differences between the original simulation model and the current model S700 source design. Methods: Design information from measurements of dissected model S700 sources and from vendor-supplied CAD drawings was used to aid establishment of an updated Monte Carlo source model, which included the complex-shaped plastic source-centering insert intended to promote water flow for cooling the source anode. These data were used to create a model for subsequent radiation transport simulations in a water phantom. Compared to the 2006 simulation geometry, the influence of volume averaging close to the source was substantially reduced. A track-length estimator was used to evaluate collision kerma as a function of radial distance and polar angle for determination of TG-43 dosimetry parameters. Results for the 50 kV source were determined every 0.1 cm from 0.3 to 15 cm and every 1° from 0° to 180°. Photon spectra in water with 0.1 keV resolution were also obtained from 0.5 to 15 cm and polar angles from 0° to 165°. Simulations were run for 10{sup 10} histories, resulting in statistical uncertainties on the transverse plane of 0.04% at r = 1 cm and 0.06% at r = 5 cm. Results: The dose-rate distribution ratio for the model S700 source as compared to the 2006 model exceeded unity by more than 5% for roughly one quarter of the solid angle surrounding the source, i.e., θ ≥ 120°. The radial dose function diminished in a similar manner as for an {sup 125}I seed, with values of 1.434, 0.636, 0.283, and 0.0975 at 0.5, 2, 5, and 10 cm, respectively. The radial dose

Including estimates of the future in today's financial statements

OpenAIRE

Mary Barth

2006-01-01

This paper explains why the question is how, not if, today's financial statements should include estimates of the future. Including such estimates is not new, but their use is increasing. This increase results primarily because standard setters believe asset and liability measures that reflect current economic conditions and up-to-date expectations of the future will result in more useful information for making economic decisions, which is the objective of financial reporting. This is why sta...

Effect of reflection on Hα emissions in Alcator C-MOD

International Nuclear Information System (INIS)

Karney, C.F.; Stotler, D.P.; Skinner, C.H.; Terry, J.L.; Pappas, D.A.

1999-01-01

In order to explain anomalous intensity ratios which have been observed in Alcator C-MOD, the H α emissions in that experiment have been modeled with the DEGAS 2 code including the effects of wall reflection. By assuming that the first wall has different reflection coefficients for the two polarizations, we have qualitatively reproduced the observed anomaly. copyright 1999 American Institute of Physics

The high resolution shear wave seismic reflection technique

International Nuclear Information System (INIS)

Johnson, W.J.; Clark, J.C.

1991-04-01

This report presents the state-of-the-art of the high resolution S-wave reflection technique. Published and unpublished literature has been reviewed and discussions have been held with experts. Result is to confirm that the proposed theoretical and practical basis for identifying aquifer systems using both P- and S-wave reflections is sound. Knowledge of S-wave velocity and P-wave velocity is a powerful tool for assessing the fluid characteristics of subsurface layers. Material properties and lateral changes in material properties such as change from clay to sand, can be inferred from careful dual evaluation of P and S-wave records. The high resolution S-wave reflection technique has seen its greatest application to date as part of geotechnical studies for building foundations in the Far East. Information from this type of study has been evaluated and will be incorporated in field studies. In particular, useful information regarding S-wave sources, noise suppression and recording procedures will be incorporated within the field studies. Case histories indicate that the best type of site for demonstrating the power of the high resolution S-wave technique will be in unconsolidated soil without excessive structural complexities. More complex sites can form the basis for subsequent research after the basic principles of the technique can be established under relatively uncomplicated conditions

Reflection of Alfven waves at an open magnetopause

International Nuclear Information System (INIS)

Cao, F.; Kan, J.R.

1990-01-01

Reflection of an Alfven wave incident on an open magnetopause form the magnetospheric side is examined. An open magnetopause, whose structure is different from the standard rotational discontinuity, is assumed to be a parameterized discontinuity with a nonzero normal field component. When an Alfven wave is incident on the open magnetopause, reflected and transmitted waves are generated. The emanating waves can be analyzed using linearized MHD conservation relations across the magnetopause, together with Snell's law. Under the assumption that the magnetic fields on the two sides of the open magnetopause are coplanar with the normal direction of the magnetopause, the governing equations are solved numerically. The results show that the electric fields of emanating Alfven waves depend mainly on the number density and the magnetic field jumps across the magnetopause. Under conditions representing the open magnetopause, it turns out that the open magnetopause behaves like a near perfect reflector. The corresponding reflection coefficient for the wave electric field can be approximated by R E = E r /E i ∼ -1 as has been deduced by Kan and Sun (1985) based on physical arguments. In other words, the solar wind flow is more or less unchanged by the loading effect of the Alfven wave incident on the magnetopause from the magnetospheric side. Therefore, under the assumptions of the model, the open magnetopause can be viewed as a constant voltage source

Highly directive Fabry-Perot leaky-wave nanoantennas based on optical partially reflective surfaces

Energy Technology Data Exchange (ETDEWEB)

Lorente-Crespo, M.; Mateo-Segura, C., E-mail: C.Mateo-Segura@hw.ac.uk [Institute of Sensors, Signals and Systems, Heriot-Watt University, EH14 4AS Edinburgh (United Kingdom)

2015-05-04

Nanoantennas enhance the conversion between highly localized electromagnetic fields and far-field radiation. Here, we investigate the response of a nano-patch partially reflective surface backed with a silver mirror to an optical source embedded at the centre of the structure. Using full wave simulations, we demonstrate a two orders of magnitude increased directivity compared to the isotropic radiator, 50% power confinement to a 13.8° width beam and a ±16 nm bandwidth. Our antenna does not rely on plasmonic phenomena thus reducing non-radiative losses and conserving source coherence.

Reflection as a Learning Tool in Graduate Medical Education: A Systematic Review.

Science.gov (United States)

Winkel, Abigail Ford; Yingling, Sandra; Jones, Aubrie-Ann; Nicholson, Joey

2017-08-01

Graduate medical education programs employ reflection to advance a range of outcomes for physicians in training. However, the most effective applications of this tool have not been fully explored. A systematic review of the literature examined interventions reporting the use of reflection in graduate medical education. The authors searched Medline/PubMed, Embase, Cochrane CENTRAL, and ERIC for studies of reflection as a teaching tool to develop medical trainees' capacities. Key words and subject headings included reflection , narrative , residents/GME , and education / teaching / learning . No language or date limits were applied. The search yielded 1308 citations between inception for each database and June 15, 2015. A total of 16 studies, encompassing 477 residents and fellows, met eligibility criteria. Study quality was assessed using the Critical Appraisal Skills Programme Qualitative Checklist. The authors conducted a thematic analysis of the 16 articles. Outcomes studied encompassed the impact of reflection on empathy, comfort with learning in complex situations, and engagement in the learning process. Reflection increased learning of complex subjects and deepened professional values. It appears to be an effective tool for improving attitudes and comfort when exploring difficult material. Limitations include that most studies had small samples, used volunteers, and did not measure behavioral outcomes. Critical reflection is a tool that can amplify learning in residents and fellows. Added research is needed to understand how reflection can influence growth in professional capacities and patient-level outcomes in ways that can be measured.

The space-time outside a source of gravitational radiation: the axially symmetric null fluid

Energy Technology Data Exchange (ETDEWEB)

Herrera, L. [Universidad Central de Venezuela, Escuela de Fisica, Facultad de Ciencias, Caracas (Venezuela, Bolivarian Republic of); Universidad de Salamanca, Instituto Universitario de Fisica Fundamental y Matematicas, Salamanca (Spain); Di Prisco, A. [Universidad Central de Venezuela, Escuela de Fisica, Facultad de Ciencias, Caracas (Venezuela, Bolivarian Republic of); Ospino, J. [Universidad de Salamanca, Departamento de Matematica Aplicada and Instituto Universitario de Fisica Fundamental y Matematicas, Salamanca (Spain)

2016-11-15

We carry out a study of the exterior of an axially and reflection symmetric source of gravitational radiation. The exterior of such a source is filled with a null fluid produced by the dissipative processes inherent to the emission of gravitational radiation, thereby representing a generalization of the Vaidya metric for axially and reflection symmetric space-times. The role of the vorticity, and its relationship with the presence of gravitational radiation is put in evidence. The spherically symmetric case (Vaidya) is, asymptotically, recovered within the context of the 1 + 3 formalism. (orig.)

NuSTAR Reveals Relativistic Reflection but no Ultra-fast Outflow in the Quasar PG1211+143

DEFF Research Database (Denmark)

Zoghbi, A.; Miller, J. M.; Walton, D. J.

2015-01-01

We report on four epochs of observations of the quasar PG 1211+143 using NuSTAR. The net exposure time is 300 ks. Prior work on this source found suggestive evidence of an ultra-fast outflow ( UFO) in the Fe K band with a velocity of approximately 0.1c. The putative flow would carry away a high...... a broad Fe K emission line and Compton back-scattering curvature. The data offer only weak constraints on the spin of the black hole. A careful search for UFOs shows no significant absorption feature above 90% confidence. The limits are particularly tight when relativistic reflection is included. We...

Justifying the Use of Internet Sources in School Assignments on Controversial Issues

Science.gov (United States)

Mikkonen, Teemu

2018-01-01

Introduction: This study concerns students' criteria in the evaluation of Internet sources for a school assignment requiring reflections on a controversial issue. The findings are elaborated by analysing students' discursive accounts in justifying the use or non-use of sources. Method: The interview data was collected in a Finnish upper secondary…

13 CFR 120.102 - Funds not available from alternative sources, including personal resources of principals.

Science.gov (United States)

2010-01-01

... source) when that owner's liquid assets exceed the amounts specified in paragraphs (a) (1) through (3) of... applicant must inject any personal liquid assets which are in excess of two times the total financing... the applicant must inject any personal liquid assets which are in excess of one and one-half times the...

High-reflective colorful films fabricated by all-solid multi-layer cholesteric structures

Science.gov (United States)

Li, Y.; Luo, D.

2018-02-01

We demonstrate all-solid-state film with high-reflectivity based on cholesteric template. The adhesive (NOA81) is both filler and an adhesive, which can be avoids interfacial losses. The reflected right- and left-circularly polarized light has been developed by roll-to-roll method, and the reflectance of the films is more than 78%. Here, the all-solid film was used in distribute feedback laser with dye-doped. In addition, this films also used in include flexible reflective display, color pixels in digital photographs, printing and colored cladding of variety of objects.

SO2 frost - UV-visible reflectivity and Io surface coverage

Science.gov (United States)

Nash, D. B.; Fanale, F. P.; Nelson, R. M.

1980-01-01

The reflectance spectrum in the range 0.24-0.85 microns of SO2 frost is measured in light of the discovery of SO2 gas in the atmosphere of Io and the possible discovery of the frost on its surface. Frost deposits up to 1.5 mm thick were grown in vacuum at 130 K and bi-directional reflectance spectra were obtained. Typical SO2 frost is found to exhibit very low reflectivity (2-5%) at 0.30 microns, rising steeply at 0.32 microns to attain a maximum reflectivity (75-80%) at 4.0 microns and uniformly high reflectivity throughout the visible and near infrared. Comparison with the full disk spectrum of Io reveals that no more than 20% of the surface can be covered with optically thick SO2 frost. Combinations of surface materials including SO2 frost which can produce the observed spectrum are indicated.

Numerical Study on Critical Wedge Angle of Cellular Detonation Reflections

International Nuclear Information System (INIS)

Gang, Wang; Kai-Xin, Liu; De-Liang, Zhang

2010-01-01

The critical wedge angle (CWA) for the transition from regular reflection (RR) to Mach reflection (MR) of a cellular detonation wave is studied numerically by an improved space-time conservation element and solution element method together with a two-step chemical reaction model. The accuracy of that numerical way is verified by simulating cellular detonation reflections at a 19.3° wedge. The planar and cellular detonation reflections over 45°–55° wedges are also simulated. When the cellular detonation wave is over a 50° wedge, numerical results show a new phenomenon that RR and MR occur alternately. The transition process between RR and MR is investigated with the local pressure contours. Numerical analysis shows that the cellular structure is the essential reason for the new phenomenon and the CWA of detonation reflection is not a certain angle but an angle range. (fundamental areas of phenomenology(including applications))

MILDOS-AREA: An enhanced version of MILDOS for large-area sources

International Nuclear Information System (INIS)

Yuan, Y.C.; Wang, J.H.C.; Zielen, A.

1989-06-01

The MILDOS-AREA computer code is a modified version of the MILDOS code, which estimates the radiological impacts of airborne emissions from uranium mining and milling facilities or any other large-area source involving emissions of radioisotopes of the uranium-238 series. MILDOS-AREA is designed for execution on personal computers. The modifications incorporated in the MILDOS-AREA code provide enhanced capabilities for calculating doses from large-area sources and update dosimetry calculations. The major revision from the original MILDOS code is the treatment of atmospheric dispersion from area sources: MILDOS-AREA substitutes a finite element integration approach for the virtual-point method (the algorithm used in the original MILDOS code) when specified by the user. Other revisions include the option of using Martin-Tickvart dispersion coefficients in place of Briggs coefficients for a given source, consideration of plume reflection, and updated internal dosimetry calculations based on the most recent recommendations of the International Commission on Radiation Protection and the age-specific dose calculation methodology developed by Oak Ridge National Laboratory. This report also discusses changes in computer code structure incorporated into MILDOS-AREA, summarizes data input requirements, and provides instructions for installing and using the program on personal computers. 15 refs., 9 figs., 26 tabs

Imaging Shallow Aquitard Breaches with P waves: Results from a Walk-away test and a Reflection Survey at two Sites in Memphis, Tennessee, USA

Science.gov (United States)

Ge, J.; Magnani, M.; Waldron, B. A.

2006-12-01

We present the results of two seismic reflection experiments conducted in the Great Memphis area in April and July 2006. The two experiments consisted in a walk-away test and in the acquisition of a 1 km seismic reflection profile. The acquisition of the seismic data is part of a larger effort aimed at imaging the lateral continuity of the Upper Claiborne confining clay that separates the Memphis aquifer, the region's primary drinking water source, from the upper unconfined aquifer and protects the drinking aquifer from exposure to potential contamination. During the walk-away test, four P-wave sources, a 7.5 kg sledge hammer, a 20 kg weight drop, a 12-gauge Buffalo gun, and a Minivibe source were tested at two sites with the goal of selecting the best P-wave seismic source and acquisition parameters for shallow reflection surveys. Boreholes nearby both sites encountered the Upper Claiborne unit at a depth ranging from 10 m to 40 m. One site is located within a 100-meter length of road median that can be considered an urban environment. The second site is located at Shelby Farms within the City of Memphis yet reflects a rural setting with minimal noise and no subsurface infrastructure. Performing identical walk-away tests at both sites, the results indicate that the energy source selection is site dependent. At the urban site, the energy generated by the weight drop source is more coherent and can be interpreted with more confidence on the recorded data. However the Shelby Farms site the 12-gauge shotgun produced the strongest recorded energy, the highest dominant frequency and the broadest frequency band (6- 110 Hz). Strong attenuations are observed at both sites with a much higher attenuation in the urban road median site, where the near surface materials consisted of gravels, sands, clays, and pebbles. For both sites, surface waves and refractions dominate the seismic recordings. Filtering and gain of the data revealed the presence of shallow reflections related

Reflections on science and the communication sector

Science.gov (United States)

Raes, Frank

2015-04-01

Reflections on science and the communication sector. In this contribution I will reflect about successes and failures in communicating climate change and air pollution sciences to the general public. These communication efforts included writing popular articles, giving public presentations, working with people from the social scientists and artists. Giving the fact that communication is a very important (economic) sector on its own, the question is to what extent scientists should enter that sector, whether scientists are at all accepted in that sector, whether they should use the expertise in that sector, or whether they should merely provide the knowledge to be used by that sector.

Near zero reflection by nanostructured anti-reflection coating design for Si substrates

Science.gov (United States)

Al-Fandi, Mohamed; Makableh, Yahia F.; Khasawneh, Mohammad; Rabady, Rabi

2018-05-01

The nanostructure design of near zero reflection coating for Si substrates by using ZnO Nanoneedles (ZnONN) is performed and optimized for the visible spectral range. The design investigates the ZnONN tip to body ratio effect on the anti-reflection coating properties. Different tip to body ratios are used on Si substrates. Around zero reflection is achieved by the Nanoneedles structure design presented in this work, leading to minimal reflection losses from the Si surface. The current design evolves a solution to optical losses and surface contamination effects associated with Si solar cells.

Propagation characteristics of audible noise generated by single corona source under positive DC voltage

Directory of Open Access Journals (Sweden)

Xuebao Li

2017-10-01

Full Text Available The directivity and lateral profile of corona-generated audible noise (AN from a single corona source are measured through experiments carried out in the semi-anechoic laboratory. The experimental results show that the waveform of corona-generated AN consists of a series of random sound pressure pulses whose pulse amplitudes decrease with the increase of measurement distance. A single corona source can be regarded as a non-directional AN source, and the A-weighted SPL (sound pressure level decreases 6 dB(A as doubling the measurement distance. Then, qualitative explanations for the rationality of treating the single corona source as a point source are given on the basis of the Ingard’s theory for sound generation in corona discharge. Furthermore, we take into consideration of the ground reflection and the air attenuation to reconstruct the propagation features of AN from the single corona source. The calculated results agree with the measurement well, which validates the propagation model. Finally, the influence of the ground reflection on the SPL is presented in the paper.

Reflection processing of the large-N seismic data from the Source Physics Experiment (SPE)

Energy Technology Data Exchange (ETDEWEB)

Paschall, Olivia C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-07-18

The purpose of the SPE is to develop a more physics-based model for nuclear explosion identification to understand the development of S-waves from explosion sources in order to enhance nuclear test ban treaty monitoring.

Characterization of reflectance variability in the industrial paint application of automotive metallic coatings by using principal component analysis

Science.gov (United States)

Medina, José M.; Díaz, José A.

2013-05-01

We have applied principal component analysis to examine trial-to-trial variability of reflectances of automotive coatings that contain effect pigments. Reflectance databases were measured from different color batch productions using a multi-angle spectrophotometer. A method to classify the principal components was used based on the eigenvalue spectra. It was found that the eigenvalue spectra follow distinct power laws and depend on the detection angle. The scaling exponent provided an estimation of the correlation between reflectances and it was higher near specular reflection, suggesting a contribution from the deposition of effect pigments. Our findings indicate that principal component analysis can be a useful tool to classify different sources of spectral variability in color engineering.

A system for the obtention and analysis of diffuse reflection spectra from biological tissue

International Nuclear Information System (INIS)

La Cadena, A. de; La Rosa, J. de; Stolik, S.

2012-01-01

The diffuse reflection spectroscopy is a technique with is possible to study biological tissue. In the field of the biomedical applications is useful for diagnostic purposes, since is possible to analyze biological tissue in a non invasive way. also, can be used with therapeutical purposes, for example in photodynamic therapy or laser surgery because with this technique it can be determined the biological effects produced by these treatments. In this paper is shown the development of a system to obtain and analyze diffuse reflection spectra of biological tissues, using a LED as a light source, that emits light between 400-700nm. The system has an interface for the regulation of the emittance of the LED. For diffuse reflectance spectra analysis, we use an HR4000CG-UV-NIR spectrometer. (Author)

A STRUGGLE FOR LOVE OF BELLA SWAN REFLECTED IN NEW MOON MOVIE: AN INDIVIDUAL PSYCHOLOGICAL APPROACH

Directory of Open Access Journals (Sweden)

Ayu Riska Lestari

2012-12-01

Full Text Available This paper described the struggle for love of Bella Swan reflected in New Moon movie by using Alfred Adler’s individual psychology and analyzed the plot of the movie. It used qualitative research method and the object of this study was a major character named Bella Swan. Primary data sources were the New Moon movie directed by Christopher Weitz and the script of the movie, while secondary data sources were collected from many sources such as dictionary, articles from internet, and books related to this study. Methods of data collecting were observation and library research. The method of data analysis was descriptive analysis. Based on the analysis, It reflected the condition of a person who had a goal and struggle to get it. It concluded that Bella had high struggles to reach her goals. The plot of New Moon movie is complicated and stimulating, therefore it made the story was not flat and boring. By analyzing the plot, the viewers could easily understand the story and the message of the movie and catch up the moral lesson of it.

Contribution of PAHs from coal-tar pavement sealcoat and other sources to 40 U.S. lakes

Science.gov (United States)

Van Metre, Peter C.; Mahler, Barbara J.

2010-01-01

Contamination of urban lakes and streams by polycyclic aromatic hydrocarbons (PAHs) has increased in the United States during the past 40 years. We evaluated sources of PAHs in post-1990 sediments in cores from 40 lakes in urban areas across the United States using a contaminant mass-balance receptor model and including as a potential source coal-tar-based (CT) sealcoat, a recently recognized source of urban PAH. Other PAH sources considered included several coal- and vehicle-related sources, wood combustion, and fuel-oil combustion. The four best modeling scenarios all indicate CT sealcoat is the largest PAH source when averaged across all 40 lakes, contributing about one-half of PAH in sediment, followed by vehicle-related sources and coal combustion. PAH concentrations in the lakes were highly correlated with PAH loading from CT sealcoat (Spearman's rho=0.98), and the mean proportional PAH profile for the 40 lakes was highly correlated with the PAH profile for dust from CT-sealed pavement (r=0.95). PAH concentrations and mass and fractional loading from CT sealcoat were significantly greater in the central and eastern United States than in the western United States, reflecting regional differences in use of different sealcoat product types. The model was used to calculate temporal trends in PAH source contributions during the last 40 to 100 years to eight of the 40 lakes. In seven of the lakes, CT sealcoat has been the largest source of PAHs since the 1960s, and in six of those lakes PAH trends are upward. Traffic is the largest source to the eighth lake, located in southern California where use of CT sealcoat is rare.

Experience with the UHV box coater and the evaporation procedure for VUV reflective coatings on the HADES RICH mirror

CERN Document Server

Maier-Komor, P; Wieser, J; Ulrich, A

1999-01-01

An UHV box coater was set up for the deposition of highly reflective layers in the vacuum ultraviolet (VUV) wavelength range on large-area mirror substrates. The VUV mirrors are needed for the ring imaging Cherenkov (RICH) detector of the high-acceptance di-electron spectrometer (HADES). The complete dry vacuum system is described. The spatial deposition distribution from the evaporation sources was measured. The reflectivity of the Al mirror layer was optimized for the wavelength range of 145-210 nm by varying the thickness of the MgF sub 2 protective layer. The setup for measuring the reflectivity in the VUV range is described and reflectivity data are presented.

Postgraduate Education to Support Organisation Change: A Reflection on Reflection

Science.gov (United States)

Stewart, Jim; Keegan, Anne; Stevens, Pam

2008-01-01

Purpose: This paper aims to explore how teaching and assessing reflective learning skills can support postgraduate practitioners studying organisational change and explores the challenges for tutors in assessing these journals. Design/methodology/approach: Assessment criteria were developed from the literature on reflective practice and…

Geochemical evidence for diversity of dust sources in the southwestern United States

Science.gov (United States)

Reheis, M.C.; Budahn, J.R.; Lamothe, P.J.

2002-01-01

Several potential dust sources, including generic sources of sparsely vegetated alluvium, playa deposits, and anthropogenic emissions, as well as the area around Owens Lake, California, affect the composition of modern dust in the southwestern United States. A comparison of geochemical analyses of modern and old (a few thousand years) dust with samples of potential local sources suggests that dusts reflect four primary sources: (1) alluvial sediments (represented by Hf, K, Rb, Zr, and rare-earth elements, (2) playas, most of which produce calcareous dust (Sr, associated with Ca), (3) the area of Owens (dry) Lake, a human-induced playa (As, Ba, Li, Pb, Sb, and Sr), and (4) anthropogenic and/or volcanic emissions (As, Cr, Ni, and Sb). A comparison of dust and source samples with previous analyses shows that Owens (dry) Lake and mining wastes from the adjacent Cerro Gordo mining district are the primary sources of As, Ba, Li, and Pb in dusts from Owens Valley. Decreases in dust contents of As, Ba, and Sb with distance from Owens Valley suggest that dust from southern Owens Valley is being transported at least 400 km to the east. Samples of old dust that accumulated before European settlement are distinctly lower in As, Ba, and Sb abundances relative to modern dust, likely due to modern transport of dust from Owens Valley. Thus, southern Owens Valley appears to be an important, geochemically distinct, point source for regional dust in the southwestern United States. Copyright ?? 2002 Elsevier Science Ltd.

Source-based neurofeedback methods using EEG recordings: training altered brain activity in a functional brain source derived from blind source separation

Science.gov (United States)

White, David J.; Congedo, Marco; Ciorciari, Joseph

2014-01-01

A developing literature explores the use of neurofeedback in the treatment of a range of clinical conditions, particularly ADHD and epilepsy, whilst neurofeedback also provides an experimental tool for studying the functional significance of endogenous brain activity. A critical component of any neurofeedback method is the underlying physiological signal which forms the basis for the feedback. While the past decade has seen the emergence of fMRI-based protocols training spatially confined BOLD activity, traditional neurofeedback has utilized a small number of electrode sites on the scalp. As scalp EEG at a given electrode site reflects a linear mixture of activity from multiple brain sources and artifacts, efforts to successfully acquire some level of control over the signal may be confounded by these extraneous sources. Further, in the event of successful training, these traditional neurofeedback methods are likely influencing multiple brain regions and processes. The present work describes the use of source-based signal processing methods in EEG neurofeedback. The feasibility and potential utility of such methods were explored in an experiment training increased theta oscillatory activity in a source derived from Blind Source Separation (BSS) of EEG data obtained during completion of a complex cognitive task (spatial navigation). Learned increases in theta activity were observed in two of the four participants to complete 20 sessions of neurofeedback targeting this individually defined functional brain source. Source-based EEG neurofeedback methods using BSS may offer important advantages over traditional neurofeedback, by targeting the desired physiological signal in a more functionally and spatially specific manner. Having provided preliminary evidence of the feasibility of these methods, future work may study a range of clinically and experimentally relevant brain processes where individual brain sources may be targeted by source-based EEG neurofeedback. PMID

Seismic reflection survey conducted in Benton County, Washinton

International Nuclear Information System (INIS)

Beggs, H.G.; Heineck, R.L.

1980-01-01

The massive Columbia River Basalt group that underlies the Hanford Site is being considered as a potential geologic repository for spent nuclear fuel. As part of the effort to ascertain and better understand the physical and geological properties of these basalt flows, a multiphased seismic reflection program has been undertaken. This phase was designed to more thoroughly define geologic features and structural attitudes in an areas in the central part of the Hanford Site. The specific feature of interest is known as the Cold Creek Syncline. This seismic survey, utilized the ''VIBROSEIS'' energy source and multifold common depth point recording. 2 figs

Reflection seismic studies over the end-glacial Burträsk fault, Skellefteå, Sweden

Directory of Open Access Journals (Sweden)

C. Juhlin

2011-01-01

Full Text Available Reflection seismic data were acquired along a ca. 22 km long profile over the end-glacial Burträsk fault with a nominal receiver and source spacing of 20 m. A steeply dipping reflection can be correlated to the Burträsk fault, indicating that the fault dips at about 55° to the southeast near the surface. The reflection from the fault is rather poorly imaged, probably due to a lateral offset in the fault of about 1 km at this location and the crookedness of the seismic profile in the vicinity of the fault. A more pronounced steeply dipping reflection is observed about 4 km southeast of the Burträsk fault. Based on its correlation with a topographic low at the surface this reflection is interpreted to originate from a fracture zone. There are no signs of large displacements along this zone as the glacial ice receded, but earthquakes could be associated with it today. Other reflections on the processed seismic section may originate from changes in lithological variations in the supra-crustal rocks or from intrusions of more mafic rock. Constraints on the fault geometry provided by the reflection seismic data will help determine what stresses were required to activate the fault when the major rupture along it occurred ca. 9500 years ago.

[Self-reflection, interpersonal behavior and psychoanalytic ethics].

Science.gov (United States)

Bürgy, M

1997-05-01

In the middle ages, ethical practice included a metaphysical theory of value. In comparison with that, self-reflection and interpersonality should be described as principles of more individual ethics and proceeding from philosophy to psychoanalysis in modern times. Drawing a borderline between human philosophy and metaphysies, Kant defined his so-called categorial imperative as a basic phenomenon of human reciprocity. Ethical relationship to another person, however, requires realization of one's own self, i.e. self-reflection. Hegel's subsequent association of intersubjectivity and selfreflection supplied the basis for Sarte's constitution of consciousness: Existence as existing for the good of the fellow-being. Self-reflection, basing on the sight of one's own self by the other person, leads to Sartre's concept of existential psychoanalysis and to his understanding of ethics. His concept illustrates the decline of significance of philosophy for the analysis of human relationship. Habermas describes self-reflection and interpersonality as fundamental principles of the psychoanalytic therapy and its ethical demands. With the historical concept of the super-ego, Freud established therapeutical one-sidedness and abstinence from ethics; however, as therapeutical interrelationship continued to intensity, ethics of depth psychology also began to develop. This ethical demand was not expressly formulated within the context of psychoanalysis, with the exception of jung and his epigones. Nevertheless, psychoanalytic interaction implies the development of self-reflection, which definitely represents a step forward in the sense of "ethical enlightenment" represented by Kant.

Quality Assessment of Landsat Surface Reflectance Products Using MODIS Data

Science.gov (United States)

Feng, Min; Huang, Chengquan; Channan, Saurabh; Vermote, Eric; Masek, Jeffrey G.; Townshend, John R.

2012-01-01

Surface reflectance adjusted for atmospheric effects is a primary input for land cover change detection and for developing many higher level surface geophysical parameters. With the development of automated atmospheric correction algorithms, it is now feasible to produce large quantities of surface reflectance products using Landsat images. Validation of these products requires in situ measurements, which either do not exist or are difficult to obtain for most Landsat images. The surface reflectance products derived using data acquired by the Moderate Resolution Imaging Spectroradiometer (MODIS), however, have been validated more comprehensively. Because the MODIS on the Terra platform and the Landsat 7 are only half an hour apart following the same orbit, and each of the 6 Landsat spectral bands overlaps with a MODIS band, good agreements between MODIS and Landsat surface reflectance values can be considered indicators of the reliability of the Landsat products, while disagreements may suggest potential quality problems that need to be further investigated. Here we develop a system called Landsat-MODIS Consistency Checking System (LMCCS). This system automatically matches Landsat data with MODIS observations acquired on the same date over the same locations and uses them to calculate a set of agreement metrics. To maximize its portability, Java and open-source libraries were used in developing this system, and object-oriented programming (OOP) principles were followed to make it more flexible for future expansion. As a highly automated system designed to run as a stand-alone package or as a component of other Landsat data processing systems, this system can be used to assess the quality of essentially every Landsat surface reflectance image where spatially and temporally matching MODIS data are available. The effectiveness of this system was demonstrated using it to assess preliminary surface reflectance products derived using the Global Land Survey (GLS) Landsat

Sequential fitting-and-separating reflectance components for analytical bidirectional reflectance distribution function estimation.

Science.gov (United States)

Lee, Yu; Yu, Chanki; Lee, Sang Wook

2018-01-10

We present a sequential fitting-and-separating algorithm for surface reflectance components that separates individual dominant reflectance components and simultaneously estimates the corresponding bidirectional reflectance distribution function (BRDF) parameters from the separated reflectance values. We tackle the estimation of a Lafortune BRDF model, which combines a nonLambertian diffuse reflection and multiple specular reflectance components with a different specular lobe. Our proposed method infers the appropriate number of BRDF lobes and their parameters by separating and estimating each of the reflectance components using an interval analysis-based branch-and-bound method in conjunction with iterative K-ordered scale estimation. The focus of this paper is the estimation of the Lafortune BRDF model. Nevertheless, our proposed method can be applied to other analytical BRDF models such as the Cook-Torrance and Ward models. Experiments were carried out to validate the proposed method using isotropic materials from the Mitsubishi Electric Research Laboratories-Massachusetts Institute of Technology (MERL-MIT) BRDF database, and the results show that our method is superior to a conventional minimization algorithm.

Method of Detecting Coliform Bacteria and Escherichia Coli Bacteria from Reflected Light

Science.gov (United States)

Vincent, Robert (Inventor)

2013-01-01

The present invention relates to a method of detecting coliform bacteria in water from reflected light and a method of detecting Eschericha Coli bacteria in water from reflected light, and also includes devices for the measurement, calculation and transmission of data relating to that method.

Genotypic and phenotypic diversity of Ralstonia pickettii and Ralstonia insidiosa isolates from clinical and environmental sources including High-purity Water.

LENUS (Irish Health Repository)

Ryan, Michael P

2011-08-30

Abstract Background Ralstonia pickettii is a nosocomial infectious agent and a significant industrial contaminant. It has been found in many different environments including clinical situations, soil and industrial High Purity Water. This study compares the phenotypic and genotypic diversity of a selection of strains of Ralstonia collected from a variety of sources. Results Ralstonia isolates (fifty-nine) from clinical, industrial and environmental origins were compared genotypically using i) Species-specific-PCR, ii) PCR and sequencing of the 16S-23S rRNA Interspatial region (ISR) iii) the fliC gene genes, iv) RAPD and BOX-PCR and v) phenotypically using biochemical testing. The species specific-PCR identified fifteen out of fifty-nine designated R. pickettii isolates as actually being the closely related species R. insidiosa. PCR-ribotyping of the 16S-23S rRNA ISR indicated few major differences between the isolates. Analysis of all isolates demonstrated different banding patterns for both the RAPD and BOX primers however these were found not to vary significantly. Conclusions R. pickettii species isolated from wide geographic and environmental sources appear to be reasonably homogenous based on genotypic and phenotypic characteristics. R. insidiosa can at present only be distinguished from R. pickettii using species specific PCR. R. pickettii and R. insidiosa isolates do not differ significantly phenotypically or genotypically based on environmental or geographical origin.

Multilayer supermirrors: broadband reflection coatings for the 15- to 100-keV range

DEFF Research Database (Denmark)

Joensen, K. D.; Gorenstein, P.; Christensen, Finn Erland

1994-01-01

reflectivity for X-rays. For hard X-rays (>= 15 keV), the absorption, however, is low enough that it is possible to design supermirrors with 10 - 70% reflectivity in a band approximately equals 3 times the width of the total reflection regime. Supermirrors of W/Si and Ni/C have been successfully fabricated...... and characterized. The measured X-ray reflectivities are well accounted for by the standard dynamical theories of multilayer reflection. Hard X-ray applications that could benefit from X-ray supermirror coatings include focusing and imaging instrumentation for astrophysics, and collimating and focusing device...

Protein Data Bank Depositions from Synchrotron Sources

International Nuclear Information System (INIS)

Jiang, J.; Sweet, R.

2004-01-01

A survey and analysis of Protein Data Bank (PDB) depositions from international synchrotron radiation facilities, based on the latest released PDB entries, are reported. The results ( ) show that worldwide, every year since 1999, more than 50% of the deposited X-ray structures have used synchrotron facilities, reaching 75% by 2003. In this web-based database, all PDB entries among individual synchrotron beamlines are archived, synchronized with the weekly PDB release. Statistics regarding the quality of experimental data and the refined model for all structures are presented, and these are analysed to reflect the impact of synchrotron sources. The results confirm the common impression that synchrotron sources extend the size of structures that can be solved with equivalent or better quality than home sources

Buckling determination in reflected systems, program FLUXFIT

Energy Technology Data Exchange (ETDEWEB)

Sotic, O [Boris Kidric Institute of Nuclear Sciences Vinca, Beograd (Yugoslavia)

1971-07-01

An improvement in accuracy of determining radial and axial buckling from foil activation distributions measured in reflected cylindrical systems is given. resultant activities are fitted to radial and axial spatial functions derived from homogeneous diffusion theory. A Fortran program FLUXFIT based on the derived method is included. (author)

Reflectance dependence of polytetrafluoroethylene on thickness for xenon scintillation light

Energy Technology Data Exchange (ETDEWEB)

Haefner, J.; Neff, A.; Arthurs, M.; Batista, E.; Morton, D.; Okunawo, M.; Pushkin, K.; Sander, A. [Randall Laboratory of Physics, University of Michigan, Ann Arbor, MI 48109-1040 (United States); Stephenson, S. [Randall Laboratory of Physics, University of Michigan, Ann Arbor, MI 48109-1040 (United States); University of California Davis, Department of Physics, One Shields Ave., Davis, CA 95616 (United States); Wang, Y. [Randall Laboratory of Physics, University of Michigan, Ann Arbor, MI 48109-1040 (United States); Lorenzon, W., E-mail: lorenzon@umich.edu [Randall Laboratory of Physics, University of Michigan, Ann Arbor, MI 48109-1040 (United States)

2017-06-01

Many rare event searches including dark matter direct detection and neutrinoless double beta decay experiments take advantage of the high VUV reflective surfaces made from polytetrafluoroethylene (PTFE) reflector materials to achieve high light collection efficiency in their detectors. As the detectors have grown in size over the past decade, there has also been an increased need for ever thinner detector walls without significant loss in reflectance to reduce dead volumes around active noble liquids, outgassing, and potential backgrounds. We report on the experimental results to measure the dependence of the reflectance on thickness of two PTFE samples at wavelengths near 178 nm. No change in reflectance was observed as the wall thickness of a cylindrically shaped PTFE vessel immersed in liquid xenon was varied between 1 mm to 9.5 mm.

Projects of SR sources including research and development for insertion devices in the USSR

International Nuclear Information System (INIS)

Kulipanov, G.

1990-01-01

Some technical information on the electron and positron storage rings - SR sources that are being constructed, used or developed at the Novosibirsk Institute of Nuclear Physics (INP), is given. The parameters and construction of wigglers and undulators (electromagnetic, superconducting, and based on permanent magnets) that are intended to be used at such storage rings are described. Various schemes of installation of wigglers, undulators and FEL at storage rings is considered. The ways of minimizing the influence of their magnetic fields on particle motion in storage rings are treated. (author)

Reflection and Reflective Practice Discourses in Coaching: A Critical Analysis

Science.gov (United States)

Cushion, Christopher J.

2018-01-01

Reflection and reflective practice is seen as an established part of coaching and coach education practice. It has become a "taken-for-granted" part of coaching that is accepted enthusiastically and unquestioningly, and is assumed to be "good" for coaching and coaches. Drawing on sociological concepts, a primarily Foucauldian…

Combination of acoustical radiosity and the image source method

DEFF Research Database (Denmark)

Koutsouris, Georgios I; Brunskog, Jonas; Jeong, Cheol-Ho

2013-01-01

A combined model for room acoustic predictions is developed, aiming to treat both diffuse and specular reflections in a unified way. Two established methods are incorporated: acoustical radiosity, accounting for the diffuse part, and the image source method, accounting for the specular part...

[Self-Reflection From Group Dialogue: The Lived Experience of Psychiatric/Mental Health Nurses].

Science.gov (United States)

Chiang, Hsien-Hsien

2015-08-01

Self-reflection is an essential element of reflective practice for group facilitators. However, this element typically exists largely at the personal level and is not addressed in group dialogues of nurses. The purpose of this study was to explore the self-reflection of psychiatric nurses in a supervision group. A phenomenological approach was used to investigate the dialogues across 12 sessions in terms of discussion content and the reflective journals of the psychiatric nurse participants. The findings showed that two forms of self-reflection included: Embodied self-reflection derived from the physical sensibility and discursive self-reflection derived from the group dialogues. The embodied and discursive self-reflections promote self-awareness in nurses. The embodiment and initiation in the group facilitates the process of self-becoming through the group dialogue, which promotes self-examination and self-direction in healthcare professionals.

Analysis of Specular Reflections Off Geostationary Satellites

Science.gov (United States)

Jolley, A.

2016-09-01

Many photometric studies of artificial satellites have attempted to define procedures that minimise the size of datasets required to infer information about satellites. However, it is unclear whether deliberately limiting the size of datasets significantly reduces the potential for information to be derived from them. In 2013 an experiment was conducted using a 14 inch Celestron CG-14 telescope to gain multiple night-long, high temporal resolution datasets of six geostationary satellites [1]. This experiment produced evidence of complex variations in the spectral energy distribution (SED) of reflections off satellite surface materials, particularly during specular reflections. Importantly, specific features relating to the SED variations could only be detected with high temporal resolution data. An update is provided regarding the nature of SED and colour variations during specular reflections, including how some of the variables involved contribute to these variations. Results show that care must be taken when comparing observed spectra to a spectral library for the purpose of material identification; a spectral library that uses wavelength as the only variable will be unable to capture changes that occur to a material's reflected spectra with changing illumination and observation geometry. Conversely, colour variations with changing illumination and observation geometry might provide an alternative means of determining material types.

Obtaining local reflectivity at two-way travel time by filtering acoustic reflection data

NARCIS (Netherlands)

Slob, E.C.; Zhang, L.; Wapenaar, C.P.A.; Mihai Popovici, A.; Fomel, S.

2017-01-01

A modified implementation of Marchenko redatuming leads to a filter that removes internal multiples from reflection data. It produces local reflectivity at two-way travel time. The method creates new primary reflections resulting from emitted events that eliminate internal multiples. We call these

Hewlett-Packard's Approaches to Full Color Reflective Displays

Science.gov (United States)

Gibson, Gary

2012-02-01

Reflective displays are desirable in applications requiring low power or daylight readability. However, commercial reflective displays are currently either monochrome or capable of only dim color gamuts. Low cost, high-quality color technology would be rapidly adopted in existing reflective display markets and would enable new solutions in areas such as retail pricing and outdoor digital signage. Technical breakthroughs are required to enable bright color gamuts at reasonable cost. Pixel architectures that rely on pure reflection from a single layer of side-by-side primary-color sub-pixels use only a fraction of the display area to reflect incident light of a given color and are, therefore, unacceptably dark. Reflective devices employing stacked color primaries offer the possibility of a somewhat brighter color gamut but can be more complex to manufacture. In this talk, we describe HP's successes in addressing these fundamental challenges and creating both high performance stacked-primary reflective color displays as well as inexpensive single layer prototypes that provide good color. Our stacked displays utilize a combination of careful light management techniques, proprietary high-contrast electro-optic shutters, and highly transparent active-matrix TFT arrays based on transparent metal oxides. They also offer the possibility of relatively low cost manufacturing through roll-to-roll processing on plastic webs. To create even lower cost color displays with acceptable brightness, we have developed means for utilizing photoluminescence to make more efficient use of ambient light in a single layer device. Existing reflective displays create a desired color by reflecting a portion of the incident spectrum while absorbing undesired wavelengths. We have developed methods for converting the otherwise-wasted absorbed light to desired wavelengths via tailored photoluminescent composites. Here we describe a single active layer prototype display that utilizes these materials

HARDERSEN IRTF ASTEROID NIR REFLECTANCE SPECTRA V1.0

Data.gov (United States)

National Aeronautics and Space Administration — This dataset includes average near-infrared (NIR) reflectance spectra for 68 main-belt asteroids that were observed at the NASA Infrared Telescope Facility (IRTF),...

Development and validation of a combined phased acoustical radiosity and image source model for predicting sound fields in rooms.

Science.gov (United States)

Marbjerg, Gerd; Brunskog, Jonas; Jeong, Cheol-Ho; Nilsson, Erling

2015-09-01

A model, combining acoustical radiosity and the image source method, including phase shifts on reflection, has been developed. The model is denoted Phased Acoustical Radiosity and Image Source Method (PARISM), and it has been developed in order to be able to model both specular and diffuse reflections with complex-valued and angle-dependent boundary conditions. This paper mainly describes the combination of the two models and the implementation of the angle-dependent boundary conditions. It furthermore describes how a pressure impulse response is obtained from the energy-based acoustical radiosity by regarding the model as being stochastic. Three methods of implementation are proposed and investigated, and finally, recommendations are made for their use. Validation of the image source method is done by comparison with finite element simulations of a rectangular room with a porous absorber ceiling. Results from the full model are compared with results from other simulation tools and with measurements. The comparisons of the full model are done for real-valued and angle-independent surface properties. The proposed model agrees well with both the measured results and the alternative theories, and furthermore shows a more realistic spatial variation than energy-based methods due to the fact that interference is considered.

Studies of the Reflection, Refraction and Internal Reflection of Light

Science.gov (United States)

Lanchester, P. C.

2014-01-01

An inexpensive apparatus and associated experiments are described for studying the basic laws of reflection and refraction of light at an air-glass interface, and multiple internal reflections within a glass block. In order to motivate students and encourage their active participation, a novel technique is described for determining the refractive…

Groundwater exploration in a Quaternary sediment body by shear-wave reflection seismics

Science.gov (United States)

Pirrung, M.; Polom, U.; Krawczyk, C. M.

2008-12-01

The detailed investigation of a shallow aquifer structure is the prerequisite for choosing a proper well location for groundwater exploration drilling for human drinking water supply and subsequent managing of the aquifer system. In the case of shallow aquifers of some 10 m in depth, this task is still a challenge for high-resolution geophysical methods, especially in populated areas. In areas of paved surfaces, shallow shear-wave reflection seismics is advantageous compared to conventional P-wave seismic methods. The sediment body of the Alfbach valley within the Vulkaneifel region in Germany, partly covered by the village Gillenfeld, was estimated to have a maximum thickness of nearly 60 m. It lies on top of a complicated basement structure, constituted by an incorporated lava flow near the basement. For the positioning of new well locations, a combination of a SH-wave land streamer receiver system and a small, wheelbarrow-mounted SH-wave source was used for the seismic investigations. This equipment can be easily applied also in residential areas without notable trouble for the inhabitants. The results of the 2.5D profiling show a clear image of the sediment body down to the bedrock with high resolution. Along a 1 km seismic profile, the sediment thickness varies between 20 to more than 60 m in the centre of the valley. The reflection behaviour from the bedrock surface corroborates the hypothesis of a basement structure with distinct topography, including strong dipping events from the flanks of the valley and strong diffractions from subsurface discontinuities. The reflection seismic imaging leads to an estimation of the former shape of the valley and a reconstruction of the flow conditions at the beginning of the sedimentation process.

Professional development through attending conferences: reflections of a health librarian.

Science.gov (United States)

Jenkins, Ruth

2015-06-01

In this article, guest writer Ruth Jenkins from Berkshire Heathcare Foundation Trust reflects on two conferences she attended in 2014, LILAC and SLA. Through the process of reflection, she considers the benefits that attending conferences can have to library and information professionals in the health sector. In particular, she discusses the opportunities and areas for learning and professional development that conferences can offer including evidence-based practice and current awareness, gaining new knowledge and objectivity, and networking and the unexpected benefits of conferences. Ruth also offers some practical hints and tips on ways to facilitate your attendance at conferences, including through awards and funding. H.S. © 2015 Health Libraries Group.

Sources

International Nuclear Information System (INIS)

Duffy, L.P.

1991-01-01

This paper discusses the sources of radiation in the narrow perspective of radioactivity and the even narrow perspective of those sources that concern environmental management and restoration activities at DOE facilities, as well as a few related sources. Sources of irritation, Sources of inflammatory jingoism, and Sources of information. First, the sources of irritation fall into three categories: No reliable scientific ombudsman to speak without bias and prejudice for the public good, Technical jargon with unclear definitions exists within the radioactive nomenclature, and Scientific community keeps a low-profile with regard to public information. The next area of personal concern are the sources of inflammation. This include such things as: Plutonium being described as the most dangerous substance known to man, The amount of plutonium required to make a bomb, Talk of transuranic waste containing plutonium and its health affects, TMI-2 and Chernobyl being described as Siamese twins, Inadequate information on low-level disposal sites and current regulatory requirements under 10 CFR 61, Enhanced engineered waste disposal not being presented to the public accurately. Numerous sources of disinformation regarding low level radiation high-level radiation, Elusive nature of the scientific community, The Federal and State Health Agencies resources to address comparative risk, and Regulatory agencies speaking out without the support of the scientific community

Self-rumination, self-reflection, and depression: self-rumination counteracts the adaptive effect of self-reflection.

Science.gov (United States)

Takano, Keisuke; Tanno, Yoshihiko

2009-03-01

Self-focused attention has adaptive and maladaptive aspects: self-reflection and self-rumination [Trapnell, P. D., & Campbell, J. D. (1999). Private self-consciousness and the Five-Factor Model of personality: distinguishing rumination from reflection. Journal of Personality and Social Psychology, 76, 284-304]. Although reflection is thought to be associated with problem solving and the promotion of mental health, previous researches have shown that reflection does not always have an adaptive effect on depression. Authors have examined the causes behind this inconsistency by modeling the relationships among self-reflection, self-rumination, and depression. One hundred and eleven undergraduates (91 men and 20 women) participated in a two-time point assessment with a 3-week interval. Statistical analysis with structural equation modeling showed that self-reflection significantly predicted self-rumination, whereas self-rumination did not predict self-reflection. With regard to depression, self-reflection was associated with a lower level of depression; self-rumination, with a higher level of depression. The total effect of self-reflection on depression was almost zero. This result indicates that self-reflection per se has an adaptive effect, which is canceled out by the maladaptive effect of self-rumination, because reflectors are likely to ruminate and reflect simultaneously.

Medial prefrontal cortex subserves diverse forms of self-reflection.

Science.gov (United States)

Jenkins, Adrianna C; Mitchell, Jason P

2011-01-01

The ability to think about oneself--to self--reflect--is one of the defining features of the human mind. Recent research has suggested that this ability may be subserved by a particular brain region: the medial prefrontal cortex (MPFC). However, although humans can contemplate a variety of different aspects of themselves, including their stable personality traits, current feelings, and physical attributes, no research has directly examined the extent to which these different forms of self-reflection are subserved by common mechanisms. To address this question, participants were scanned using functional magnetic resonance imaging (fMRI) while making judgments about their own personality traits, current mental states, and physical attributes as well as those of another person. Whereas some brain regions responded preferentially during only one form of self-reflection, a robust region of MPFC was engaged preferentially during self-reflection across all three types of judgment. These results suggest that--although dissociable--diverse forms of self-referential thought draw on a shared cognitive process subserved by MPFC.

Designing museum exhibits that facilitate visitor reflection and discussion

DEFF Research Database (Denmark)

Skydsgaard, Morten Arnika; Andersen, Hanne Møller; King, Heather

2016-01-01

This paper explores how four design principles (curiosity, challenge, narratives and participation) facilitate reflection and discussion among young visitors in the issues-based exhibition Dear, Difficult Body. The investigation is based on a mixed-method approach combining questionnaire and inte......This paper explores how four design principles (curiosity, challenge, narratives and participation) facilitate reflection and discussion among young visitors in the issues-based exhibition Dear, Difficult Body. The investigation is based on a mixed-method approach combining questionnaire...... and interview data. The implementation of design principles resulted in a variety of exhibits which variously prompted reflection and discussion on the part of visitors. Exhibits with narratives, for example, here defined as both personal and expert narratives, were found to be effective in facilitating...... personal reflection but also prompted discussion. Participation, defined as including both physical interaction with exhibits, and dialogic interaction between visitors, facilitated the sharing of ideas and feelings between visitors. Exhibits with elements of curiosity and challenge were found to attract...

Nd:YAG-laser-based time-domain reflectometry measurements of the intrinsic reflection signature from PMMA fiber splices

Science.gov (United States)

Lawson, Christopher M.; Michael, Robert R., Jr.; Dressel, Earl M.; Harmony, David W.

1991-12-01

Optical time domain reflectometry (OTDR) measurements have been performed on polished polymethylmethacrylate (PMMA) plastic fiber splices. After the dominant splice reflection sources due to surface roughness, inexact index matching, and fiber core misalignment were eliminated, an intrinsic OTDR signature 3 - 8 dB above the Rayleigh backscatter floor remained with all tested fibers. This minimum splice reflectivity exhibits characteristics that are consistent with sub-surface polymer damage and can be used for detection of PMMA fiber splices.

NuSTAR Reveals Relativistic Reflection But No Ultra-Fast Outflow in the Quasar Pg∼1211+143

Science.gov (United States)

Zoghbi, A.; Miller, J. M.; Walton, D. J.; Harrison, F. A.; Fabian, A. C.; Reynolds, C. S.; Boggs, S. E.; Christensen, F. E.; Craig, W.; Hailey, C. J.; Stern, D.; Zhang, W. W.

2015-01-01

We report on four epochs of observations of the quasar PG 1211+143 using NuSTAR. The net exposure time is 300 ks. Prior work on this source found suggestive evidence of an ultra-fast outflow (UFO) in the Fe K band with a velocity of approximately 0.1c. The putative flow would carry away a high-mass flux and kinetic power, with broad implications for feedback and black hole--galaxy co-evolution. NuSTAR detects PG 1211+143 out to 30 keV, meaning that the continuum is well-defined both through and above the Fe K band. A characteristic relativistic disk reflection spectrum is clearly revealed via a broad Fe K emission line and Compton back-scattering curvature. The data offer only weak constraints on the spin of the black hole. A careful search for UFOs shows no significant absorption feature above 90% confidence. The limits are particularly tight when relativistic reflection is included. We discuss the statistics and the implications of these results in terms of connections between accretion onto quasars, Seyferts, and stellar-mass black holes, and feedback into their host environments.

NuSTAR REVEALS RELATIVISTIC REFLECTION BUT NO ULTRA-FAST OUTFLOW IN THE QUASAR PG 1211+143

International Nuclear Information System (INIS)

Zoghbi, A.; Miller, J. M.; Walton, D. J.; Stern, D.; Harrison, F. A.; Fabian, A. C.; Reynolds, C. S.; Boggs, S. E.; Craig, W.; Christensen, F. E.; Hailey, C. J.; Zhang, W. W.

2015-01-01

We report on four epochs of observations of the quasar PG 1211+143 using NuSTAR. The net exposure time is 300 ks. Prior work on this source found suggestive evidence of an ultra-fast outflow (UFO) in the Fe K band with a velocity of approximately 0.1c. The putative flow would carry away a high-mass flux and kinetic power, with broad implications for feedback and black hole--galaxy co-evolution. NuSTAR detects PG 1211+143 out to 30 keV, meaning that the continuum is well-defined both through and above the Fe K band. A characteristic relativistic disk reflection spectrum is clearly revealed via a broad Fe K emission line and Compton back-scattering curvature. The data offer only weak constraints on the spin of the black hole. A careful search for UFOs shows no significant absorption feature above 90% confidence. The limits are particularly tight when relativistic reflection is included. We discuss the statistics and the implications of these results in terms of connections between accretion onto quasars, Seyferts, and stellar-mass black holes, and feedback into their host environments

NuSTAR REVEALS RELATIVISTIC REFLECTION BUT NO ULTRA-FAST OUTFLOW IN THE QUASAR PG 1211+143

Energy Technology Data Exchange (ETDEWEB)

Zoghbi, A.; Miller, J. M. [Department of Astronomy, University of Michigan, 1085 South University Avenue, Ann Arbor, MI 48109 (United States); Walton, D. J.; Stern, D. [Jet Propulsion Laboratory, California Institute of Technology, Pasadena, CA 91109 (United States); Harrison, F. A. [Space Radiation Laboratory, California Institute of Technology, Pasadena, CA 91125 (United States); Fabian, A. C. [Institute of Astronomy, University of Cambridge, Madingley Road, Cambridge, CB3 OHA (United Kingdom); Reynolds, C. S. [Department of Astronomy, University of Maryland, College Park, MD 20742-2421 (United States); Boggs, S. E.; Craig, W. [Space Science Laboratory, University of California, Berkeley, CA 94720 (United States); Christensen, F. E. [DTU Space. National Space Institute, Technical University of Denmark, Elektrovej 327, DK-2800 Lyngby (Denmark); Hailey, C. J. [Columbia Astrophysics Laboratory, Columbia University, New York, NY 10027 (United States); Zhang, W. W., E-mail: abzoghbi@umich.edu [NASA Goddard Space Flight Center, Greenbelt, MD 20771 (United States)

2015-02-01

We report on four epochs of observations of the quasar PG 1211+143 using NuSTAR. The net exposure time is 300 ks. Prior work on this source found suggestive evidence of an ultra-fast outflow (UFO) in the Fe K band with a velocity of approximately 0.1c. The putative flow would carry away a high-mass flux and kinetic power, with broad implications for feedback and black hole--galaxy co-evolution. NuSTAR detects PG 1211+143 out to 30 keV, meaning that the continuum is well-defined both through and above the Fe K band. A characteristic relativistic disk reflection spectrum is clearly revealed via a broad Fe K emission line and Compton back-scattering curvature. The data offer only weak constraints on the spin of the black hole. A careful search for UFOs shows no significant absorption feature above 90% confidence. The limits are particularly tight when relativistic reflection is included. We discuss the statistics and the implications of these results in terms of connections between accretion onto quasars, Seyferts, and stellar-mass black holes, and feedback into their host environments.

Born reflection kernel analysis and wave-equation reflection traveltime inversion in elastic media

KAUST Repository

Wang, Tengfei

2017-08-17

Elastic reflection waveform inversion (ERWI) utilize the reflections to update the low and intermediate wavenumbers in the deeper part of model. However, ERWI suffers from the cycle-skipping problem due to the objective function of waveform residual. Since traveltime information relates to the background model more linearly, we use the traveltime residuals as objective function to update background velocity model using wave equation reflected traveltime inversion (WERTI). The reflection kernel analysis shows that mode decomposition can suppress the artifacts in gradient calculation. We design a two-step inversion strategy, in which PP reflections are firstly used to invert P wave velocity (Vp), followed by S wave velocity (Vs) inversion with PS reflections. P/S separation of multi-component seismograms and spatial wave mode decomposition can reduce the nonlinearity of inversion effectively by selecting suitable P or S wave subsets for hierarchical inversion. Numerical example of Sigsbee2A model validates the effectiveness of the algorithms and strategies for elastic WERTI (E-WERTI).

Principles of neutron reflection

International Nuclear Information System (INIS)

Felcher, G.P.

1988-08-01

Neutron reflection is perhaps the most developed branch of slow neutrons optics, which in itself is a direct consequence of the undulatory nature of the neutron. After reviewing the basic types of interactions (nuclear and magnetic) between neutrons and matter, the formalism is introduced to calculate the reflectivity from a sample composed of stacked flat layers and, inversely, to calculate the stacking from reflectivity measurements. Finally, a brief survey of the applications of neutron reflection is given, both in technology and in fundamental research. 32 refs., 6 figs

Storage array reflection considerations

International Nuclear Information System (INIS)

Haire, M.J.; Jordan, W.C.; Taylor, R.G.

1997-01-01

The assumptions used for reflection conditions of single containers are fairly well established and consistently applied throughout the industry in nuclear criticality safety evaluations. Containers are usually considered to be either fully water-reflected (i.e. surrounded by 6 to 12 in. of water) for safety calculations or reflected by 1 in. of water for nominal (structural material and air) conditions. Tables and figures are usually available for performing comparative evaluations of containers under various loading conditions. Reflection considerations used for evaluating the safety of storage arrays of fissile material are not as well established

Global anthropogenic emissions of particulate matter including black carbon

Science.gov (United States)